Viscoelastic Multicomponent Fluids in confined Flow-Focusing Devices
Gupta, Anupam
2015-01-01
The effects of elasticity on the break-up of liquid threads in microfluidic cross-junctions is investigated using numerical simulations based on the "lattice Boltzmann models" (LBM). Working at small Capillary numbers, we investigate the effects of non-Newtonian phases in the transition from droplet formation at the cross-junction (DCJ) and droplet formation downstream of the cross-junction (DC) (Liu & Zhang, ${\\it Phys. Fluids.}$ ${\\bf 23}$, 082101 (2011)). Viscoelasticity is found to influence the break-up point of the threads, which moves closer to the cross-junction and stabilizes. This is attributed to an increase of the polymer feedback stress forming in the corner flows, where the side channels of the device meet the main channel.
GIOVANGIGLI; Vincent
2012-01-01
We present multicomponent flow models derived from the kinetic theory of gases and investigate the symmetric hyperbolic-parabolic structure of the resulting system of partial differential equations.We address the Cauchy problem for smooth solutions as well as the existence of deflagration waves,also termed anchored waves.We further discuss related models which have a similar hyperbolic-parabolic structure,notably the SaintVenant system with a temperature equation as well as the equations governing chemical equilibrium flows.We next investigate multicomponent ionized and magnetized flow models with anisotropic transport fluxes which have a different mathematical structure.We finally discuss numerical algorithms specifically devoted to complex chemistry flows,in particular the evaluation of multicomponent transport properties,as well as the impact of multicomponent transport.
Multicomponent model of deformation and detachment of a biofilm under fluid flow
Tierra, Giordano; Pavissich, Juan P.; Nerenberg, Robert; Xu, Zhiliang; Alber, Mark S.
2015-01-01
A novel biofilm model is described which systemically couples bacteria, extracellular polymeric substances (EPS) and solvent phases in biofilm. This enables the study of contributions of rheology of individual phases to deformation of biofilm in response to fluid flow as well as interactions between different phases. The model, which is based on first and second laws of thermodynamics, is derived using an energetic variational approach and phase-field method. Phase-field coupling is used to model structural changes of a biofilm. A newly developed unconditionally energy-stable numerical splitting scheme is implemented for computing the numerical solution of the model efficiently. Model simulations predict biofilm cohesive failure for the flow velocity between and m s−1 which is consistent with experiments. Simulations predict biofilm deformation resulting in the formation of streamers for EPS exhibiting a viscous-dominated mechanical response and the viscosity of EPS being less than . Higher EPS viscosity provides biofilm with greater resistance to deformation and to removal by the flow. Moreover, simulations show that higher EPS elasticity yields the formation of streamers with complex geometries that are more prone to detachment. These model predictions are shown to be in qualitative agreement with experimental observations. PMID:25808342
Chemical-potential route for multicomponent fluids
Santos, Andrés; Rohrmann, René D.
2013-05-01
The chemical potentials of multicomponent fluids are derived in terms of the pair correlation functions for arbitrary number of components, interaction potentials, and dimensionality. The formally exact result is particularized to hard-sphere mixtures with zero or positive nonadditivity. As a simple application, the chemical potentials of three-dimensional additive hard-sphere mixtures are derived from the Percus-Yevick theory and the associated equation of state is obtained. This Percus-Yevick chemical-route equation of state is shown to be more accurate than the virial equation of state. An interpolation between the chemical-potential and compressibility routes exhibits a better performance than the well-known Boublík-Mansoori-Carnahan-Starling-Leland equation of state.
Spinodal decomposition in multicomponent fluid mixtures: A molecular dynamics study
Laradji, Mohamed; Mouritsen, Ole G.; Toxvaerd, Søren
1996-01-01
We have investigated the effect of the number p of components on the dynamics of phase separation in two-dimensional symmetric multicomponent fluids. In contrast to concentrated two-dimensional binary fluids, where the growth dynamics is controlled by the coupling of the velocity held to the orde...
Time-derivative preconditioning method for multicomponent flow
Housman, Jeffrey Allen
A time-derivative preconditioned system of equations suitable for the numerical simulation of single component and multicomponent inviscid flows at all speeds is formulated. The system is shown to be hyperbolic in time and remain well-posed at low Mach numbers, allowing an efficient time marching solution strategy to be utilized from transonic to incompressible flow speeds. For multicomponent flow at low speed, a preconditioned nonconservative discretization scheme is described which preserves pressure and velocity equilibrium across fluid interfaces, handles sharp liquid/gas interfaces with large density ratios, while remaining well-conditioned for time marching methods. The method is then extended to transonic and supersonic flows using a hybrid conservative/nonconservative formulation which retains the pressure/velocity equilibrium property and converges to the correct weak solution when shocks are present. In order to apply the proposed model to complex flow applications, the overset grid methodology is used where the equations are transformed to a nonorthogonal curvilinear coordinate system and discretized on structured body-fitted curvilinear grids. The multicomponent model and its extension to homogeneous multiphase mixtures is discussed and the hyperbolicity of the governing equations is demonstrated. Low Mach number perturbation analysis is then performed on the system of equations and a local time-derivative preconditioning matrix is derived allowing time marching numerical methods to remain efficient at low speeds. Next, a particular time marching numerical method is presented along with three discretization schemes for the convective terms. These include a conservative preconditioned Roe type method, a nonconservative preconditioned Split Coefficient Matrix (SCM) method, and hybrid formulation which combines the conservative and nonconservative schemes using a simple switching function. A characteristic boundary treatment which includes time
Lattice Boltzmann Models for Multicomponent Fluids
2007-11-02
between multiphase fluids. Two specific physical problems investigated: the shape of a sessile drop on a horizontal surface subjected to a gravitational field, and the effect of surface tension on contact angle .
Fluid description of multi-component solar partially ionized plasma
Khomenko, Elena; Diaz, Antonio; Vitas, Nikola
2014-01-01
We derive self-consistent formalism for the description of multi-component partially ionized solar plasma, by means of the coupled equations for the charged and neutral components for an arbitrary number of chemical species, and the radiation field. All approximations and assumptions are carefully considered. Generalized Ohm's law is derived for the single-fluid and two-fluid formalism. Our approach is analytical with some order-of-magnitude support calculations. After general equations are developed we particularize to some frequently considered cases as for the interaction of matter and radiation.
Fluid description of multi-component solar partially ionized plasma
Khomenko, E., E-mail: khomenko@iac.es; Collados, M.; Vitas, N. [Instituto de Astrofísica de Canarias, 38205 La Laguna, Tenerife (Spain); Departamento de Astrofísica, Universidad de La Laguna, 38205 La Laguna, Tenerife (Spain); Díaz, A. [Departament de Física, Universitat de les Illes Balears, E-07122 Palma de Mallorca (Spain)
2014-09-15
We derive self-consistent formalism for the description of multi-component partially ionized solar plasma, by means of the coupled equations for the charged and neutral components for an arbitrary number of chemical species, and the radiation field. All approximations and assumptions are carefully considered. Generalized Ohm's law is derived for the single-fluid and two-fluid formalism. Our approach is analytical with some order-of-magnitude support calculations. After general equations are developed, we particularize to some frequently considered cases as for the interaction of matter and radiation.
Cueto-Felgueroso, L.; Fu, X.; Juanes, R.
2016-12-01
The description of multicomponent flows with complex phase behavior remains an open challenge in pore-scale modeling. Darcy-scale general purpose simulators assume local thermodynamic equilibrium, and perform equation-of-state-based calculations to make phase equilibrium predictions; that is, to determine the phase volume fractions and their compositions from overall component mole fractions. What remains unclear is whether the thermodynamic equilibrium assumption is valid given the flow conditions, complex structure of the pore space and characteristic time scales for flow. Diffuse-interface theories of multiphase flow have recently emerged as promising tools to understand and simulate complex processes involving the simultaneous flow of two or more immiscible fluid phases. The common goal in these approaches is to formulate thermodynamically consistent stress tensors and mesoscale balance laws, including the impact of surface tension on the momentum balance, as well as properly tracking interfacial dynamics and mass transfer. We propose a phase-field model of multiphase, multicomponent flow, which we use to address the following research questions: What is the impact of the wetting conditions at the pore scale on upscaled descriptions of multiphase flow? What is the impact of the displacement dynamics, pore space structure and wetting conditions on the phase behavior of multicomponent mixtures? We finally investigate upscaling procedures to incorporate non-equilibrium phase behavior at the continuum scale.
Geophysical fluid flow experiment
Broome, B. G.; Fichtl, G.; Fowlis, W.
1979-01-01
The essential fluid flow processes associated with the solar and Jovian atmospheres will be examined in a laboratory experiment scheduled for performance on Spacelab Missions One and Three. The experimental instrumentation required to generate and to record convective fluid flow is described. Details of the optical system configuration, the lens design, and the optical coatings are described. Measurement of thermal gradient fields by schlieren techniques and measurement of fluid flow velocity fields by photochromic dye tracers is achieved with a common optical system which utilizes photographic film for data recording. Generation of the photochromic dye tracers is described, and data annotation of experimental parameters on the film record is discussed.
Equivalence of two models in single-phase multicomponent flow simulations
Wu, Yuanqing
2016-02-28
In this work, two models to simulate the single-phase multicomponent flow in reservoirs are introduced: single-phase multicomponent flow model and two-phase compositional flow model. Because the single-phase multicomponent flow is a special case of the two-phase compositional flow, the two-phase compositional flow model can also simulate the case. We compare and analyze the two models when simulating the single-phase multicomponent flow, and then demonstrate the equivalence of the two models mathematically. An experiment is also carried out to verify the equivalence of the two models.
Basniev, Kaplan S; Chilingar, George V 0
2012-01-01
The mechanics of fluid flow is a fundamental engineering discipline explaining both natural phenomena and human-induced processes, and a thorough understanding of it is central to the operations of the oil and gas industry. This book, written by some of the world's best-known and respected petroleum engineers, covers the concepts, theories, and applications of the mechanics of fluid flow for the veteran engineer working in the field and the student, alike. It is a must-have for any engineer working in the oil and gas industry.
Chella R.
2006-12-01
Full Text Available The flow of several components and several phases through a porous medium is generally described by introducing macroscopic mass-balance equations under the form of generalized dispersion equations. This model raises several questions that are discussed in this paper on the basis of results obtained from the volume averaging method, coupled with pore-scale simulations of the multiphase flow. The study is limited to a binary, two-phase system, and we assume that the momentum equations can be solved independently from the diffusion/advection equations. The assumption of local-equilibrium is discussed and several length-scale and time-scale constraints are provided. A key issue concerns the impact on the dispersion tensors of the pore-scale equilibrium condition at the interface between the different phases. Our results show that this phenomenon may lead to significant variations of the dispersion coefficients with respect to passive dispersion, i. e. , dispersion without interfacial mass fluxes. Macroscopic equations are then obtained in the general case, and several local closure problems are provided that allow one to calculate the dispersion tensors and others properties, from the pore-scale geometry, velocities, and fluid characteristics. Examples of solutions of these closure problems are given in the case of two-dimensional representative unit cells. The two-phase flow equations are solved in two different ways : a boundary element technique, or a modified lattice Boltzmann approach. Solutions of the closure problems associated with the dispersion equations are then given using a finite volume element formulation of the partial differential equations. The results show the influence of velocity and saturation on the effective parameters. They emphasize the importance of geometry on the behavior of the dispersion tensor. Extension of these results to a larger-scale including the effect of heterogeneities is proposed in a limited case
Immiscible multicomponent lattice Boltzmann model for fluids with high relaxation time ratio
Tao Jiang; Qiwei Gong; Ruofan Qiu; Anlin Wang
2014-10-01
An immiscible multicomponent lattice Boltzmann model is developed for fluids with high relaxation time ratios, which is based on the model proposed by Shan and Chen (SC). In the SC model, an interaction potential between particles is incorporated into the discrete lattice Boltzmann equation through the equilibrium velocity. Compared to the SC model, external forces in our model are discretized directly into the discrete lattice Boltzmann equation, as proposed by Guo et al. We develop it into a new multicomponent lattice Boltzmann (LB) model which has the ability to simulate immiscible multicomponent fluids with relaxation time ratio as large as 29.0 and to reduce `spurious velocity’. In this work, the improved model is validated and studied using the central bubble case and the rising bubble case. It finds good applications in both static and dynamic cases for multicomponent simulations with different relaxation time ratios.
Equilibrium structure of the multi-component screened charged hard-sphere fluid.
Sánchez-Díaz, Luis E; Mendez-Maldonado, Gloria A; González-Melchor, Minerva; Ruiz-Estrada, Honorina; Medina-Noyola, Magdaleno
2011-07-07
The generalized mean spherical approximation of the structural properties of the binary charge-symmetric fluid of screened charged hard-spheres of the same diameter, i.e., the screened restricted primitive model, is extended to include binary charge-asymmetric and multi-component fluids. Molecular dynamics simulation data are generated to assess the accuracy of the corresponding theoretical predictions.
Scaled Particle Theory for Multicomponent Hard Sphere Fluids Confined in Random Porous Media.
Chen, W; Zhao, S L; Holovko, M; Chen, X S; Dong, W
2016-06-23
The formulation of scaled particle theory (SPT) is presented for a quite general model of fluids confined in a random porous media, i.e., a multicomponent hard sphere (HS) fluid in a multicomponent hard sphere or a multicomponent overlapping hard sphere (OHS) matrix. The analytical expressions for pressure, Helmholtz free energy, and chemical potential are derived. The thermodynamic consistency of the proposed theory is established. Moreover, we show that there is an isomorphism between the SPT for a multicomponent system and that for a one-component system. Results from grand canonical ensemble Monte Carlo simulations are also presented for a binary HS mixture in a one-component HS or a one-component OHS matrix. The accuracy of various variants derived from the basic SPT formulation is appraised against the simulation results. Scaled particle theory, initially formulated for a bulk HS fluid, has not only provided an analytical tool for calculating thermodynamic properties of HS fluid but also helped to gain very useful insight for elaborating other theoretical approaches such as the fundamental measure theory (FMT). We expect that the general SPT for multicomponent systems developed in this work can contribute to the study of confined fluids in a similar way.
Non-Isothermal, Multi-phase, Multi-component Flows through Deformable Methane Hydrate Reservoirs
Gupta, Shubhangi; Wohlmuth, Barbara
2015-01-01
We present a hydro-geomechanical model for subsurface methane hydrate systems. Our model considers kinetic hydrate phase change and non-isothermal, multi-phase, multi-component flow in elastically deforming soils. The model accounts for the effects of hydrate phase change and pore pressure changes on the mechanical properties of the soil, and also for the effect of soil deformation on the fluid-solid interaction properties relevant to reaction and transport processes (e.g., permeability, capillary pressure, reaction surface area). We discuss a 'cause-effect' based decoupling strategy for the model and present our numerical discretization and solution scheme. We then identify the important model components and couplings which are most vital for a hydro-geomechanical hydrate simulator, namely, 1) dissociation kinetics, 2) hydrate phase change coupled with non-isothermal two phase two component flow, 3) two phase flow coupled with linear elasticity (poroelasticity coupling), and finally 4) hydrate phase change c...
Multicomponent fluid of hard spheres near a wall.
Malijevský, Alexandr; Yuste, Santos B; Santos, Andrés; López de Haro, Mariano
2007-06-01
The rational function approximation method, density functional theory, and NVT Monte Carlo simulation are used to obtain the density profiles of multicomponent hard-sphere mixtures near a planar hard wall. Binary mixtures with a size ratio 1:3 in which both components occupy a similar volume are specifically examined. The results indicate that the present version of density functional theory yields an excellent overall performance. A reasonably accurate behavior of the rational function approximation method is also observed, except in the vicinity of the first minimum, where it may even predict unphysical negative values.
Moortgat, J.; Amooie, M. A.; Soltanian, M. R.
2016-12-01
Problems in hydrogeology and hydrocarbon reservoirs generally involve the transport of solutes in a single solvent phase (e.g., contaminants or dissolved injection gas), or the flow of multiple phases that may or may not exchange mass (e.g., brine, NAPL, oil, gas). Often, flow is viscously and gravitationally unstable due to mobility and density contrasts within a phase or between phases. Such instabilities have been studied in detail for single-phase incompressible fluids and for two-phase immiscible flow, but to a lesser extent for multiphase multicomponent compressible flow. The latter is the subject of this presentation. Robust phase stability analyses and phase split calculations, based on equations of state, determine the mass exchange between phases and the resulting phase behavior, i.e., phase densities, viscosities, and volumes. Higher-order finite element methods and fine grids are used to capture the small-scale onset of flow instabilities. A full matrix of composition dependent coefficients is considered for each Fickian diffusive phase flux. Formation heterogeneity can have a profound impact and is represented by realistic geostatistical models. Qualitatively, fingering in multiphase compositional flow is different from single-phase problems because 1) phase mobilities depend on rock wettability through relative permeabilities, and 2) the initial density and viscosity ratios between phases may change due to species transfer. To quantify mixing rates in different flow regimes and for varying degrees of miscibility and medium heterogeneities, we define the spatial variance, scalar dissipation rate, dilution index, skewness, and kurtosis of the molar density of introduced species. Molar densities, unlike compositions, include compressibility effects. The temporal evolution of these measures shows that, while transport at the small-scale (cm) is described by the classical advection-diffusion-dispersion relations, scaling at the macro-scale (> 10 m) shows
Finite-volume WENO scheme for viscous compressible multicomponent flows
Coralic, Vedran; Colonius, Tim
2014-01-01
We develop a shock- and interface-capturing numerical method that is suitable for the simulation of multicomponent flows governed by the compressible Navier-Stokes equations. The numerical method is high-order accurate in smooth regions of the flow, discretely conserves the mass of each component, as well as the total momentum and energy, and is oscillation-free, i.e. it does not introduce spurious oscillations at the locations of shockwaves and/or material interfaces. The method is of Godunov-type and utilizes a fifth-order, finite-volume, weighted essentially non-oscillatory (WENO) scheme for the spatial reconstruction and a Harten-Lax-van Leer contact (HLLC) approximate Riemann solver to upwind the fluxes. A third-order total variation diminishing (TVD) Runge-Kutta (RK) algorithm is employed to march the solution in time. The derivation is generalized to three dimensions and nonuniform Cartesian grids. A two-point, fourth-order, Gaussian quadrature rule is utilized to build the spatial averages of the reconstructed variables inside the cells, as well as at cell boundaries. The algorithm is therefore fourth-order accurate in space and third-order accurate in time in smooth regions of the flow. We corroborate the properties of our numerical method by considering several challenging one-, two- and three-dimensional test cases, the most complex of which is the asymmetric collapse of an air bubble submerged in a cylindrical water cavity that is embedded in 10% gelatin. PMID:25110358
Multicomponent fluid of nonadditive hard spheres near a wall.
Fantoni, Riccardo; Santos, Andrés
2013-04-01
A recently proposed rational-function approximation [Phys. Rev. E 84, 041201 (2011)] for the structural properties of nonadditive hard spheres is applied to evaluate analytically (in Laplace space) the local density profiles of multicomponent nonadditive hard-sphere mixtures near a planar nonadditive hard wall. The theory is assessed by comparison with NVT Monte Carlo simulations of binary mixtures with a size ratio 1:3 in three possible scenarios: a mixture with either positive or negative nonadditivity near an additive wall, an additive mixture with a nonadditive wall, and a nonadditive mixture with a nonadditive wall. It is observed that, while the theory tends to underestimate the local densities at contact (especially in the case of the big spheres) it captures very well the initial decay of the densities with increasing separation from the wall and the subsequent oscillations.
He, Ping; Ghoniem, Ahmed F.
2017-03-01
Mixing of partially miscible fluids plays an important role in many physical and chemical processes. The modeling complexities lie in the tight coupling of the multiphase flow, heat transfer and multicomponent mass transfer, as well as diffusions across the phase interface. We present a sharp interface method for modeling such process. The non-ideal equation of state is used to compute the fluid properties such as density, fugacity and enthalpy, and to predict phase equilibrium composition. The phase interface location is tracked using the phase propagation velocity. A third-order one-sided finite difference scheme using a variable grid size according to the interface location is utilized to discretize the partial derivatives immediately next to the interface, while a second-order central scheme is used for the bulk of fluids. An optimization method, the Nelder-Mead method, is applied to search for (1) the phase compositions on both sides of the interface, and (2) the phase propagation velocity based on the coupling of the multicomponent phase equilibrium and the species' balance across the interface. The temperature at the interface is determined by the energy balance. Numerical results are used to demonstrate the convergence of our method and show its capability to simulate the mixing of multicomponent partially miscible fluids.
Acoustic concentration of particles in fluid flow
Ward, Michael D.; Kaduchak, Gregory
2010-11-23
An apparatus for acoustic concentration of particles in a fluid flow includes a substantially acoustically transparent membrane and a vibration generator that define a fluid flow path therebetween. The fluid flow path is in fluid communication with a fluid source and a fluid outlet and the vibration generator is disposed adjacent the fluid flow path and is capable of producing an acoustic field in the fluid flow path. The acoustic field produces at least one pressure minima in the fluid flow path at a predetermined location within the fluid flow path and forces predetermined particles in the fluid flow path to the at least one pressure minima.
Acoustic concentration of particles in fluid flow
Ward, Michael W.; Kaduchak, Gregory
2017-08-15
Disclosed herein is a acoustic concentration of particles in a fluid flow that includes a substantially acoustically transparent membrane and a vibration generator that define a fluid flow path therebetween. The fluid flow path is in fluid communication with a fluid source and a fluid outlet and the vibration generator is disposed adjacent the fluid flow path and is capable of producing an acoustic field in the fluid flow path. The acoustic field produces at least one pressure minima in the fluid flow path at a predetermined location within the fluid flow path and forces predetermined particles in the fluid flow path to the at least one pressure minima.
Dynamic p-enrichment schemes for multicomponent reactive flows
Michoski, C; Dawson, C; Kubatko, E J; Wirasaet, D; Westerink, J J
2011-01-01
We present a family of p-enrichment schemes. These schemes may be separated into two basic classes: the first, called \\emph{fixed tolerance schemes}, rely on setting global scalar tolerances on the local regularity of the solution, and the second, called \\emph{dioristic schemes}, rely on time-evolving bounds on the local variation in the solution. Each class of $p$-enrichment scheme is further divided into two basic types. The first type (the Type I schemes) enrich along lines of maximal variation, striving to enhance stable solutions in "areas of highest interest." The second type (the Type II schemes) enrich along lines of maximal regularity in order to maximize the stability of the enrichment process. Each of these schemes are tested over a pair of model problems arising in coastal hydrology. The first is a contaminant transport model, which addresses a declinature problem for a contaminant plume with respect to a bay inlet setting. The second is a multicomponent chemically reactive flow model of estuary e...
Multi-phase multi-component reactive flow in Geodynamics
Oliveira, Beñat; Afonso, Juan Carlos; Zlotnik, Sergio
2016-04-01
Multi-phase multi-component reactive flow (MPMCRF) controls a number of important complex geodynamic/geochemical problems, such as melt generation and percolation, metasomatism, rheological weakening, magmatic differentiation, ore emplacement, and fractionation of chemical elements, to name a few. These interacting processes occur over very different spatial and temporal scales and under very different physico-chemical conditions. Therefore, there is a strong motivation in geodynamics for investigating the equations governing MPMCRF, their mathematical structure and properties, and the numerical techniques necessary to obtain reliable and accurate results. In this contribution we present results from a novel numerical framework to solve multiscale MPMCRF problems in geodynamic contexts. Our approach is based on the effective tracking of the most basic building blocks: internal energy and chemical composition. This is achieved through the combination of rigorous solutions to the conservation equations (mass, energy and momentum) for each dynamic phase (instead of the more common "mixture-type" approach) and the transport equation for the chemical species, within the context of classical irreversible thermodynamics. Interfacial processes such as phase changes, chemical diffusion+reaction, and surface tension effects are explicitly incorporated in the context of ensemble averaging. Phase assemblages, mineral and melt compositions, and all other physical parameters of multi-phase systems are obtained through dynamic free-energy minimization procedures.
SHU BiFen; SHEN Hui; CHEN MeiYuan; XIA JianHan; WANG Xiang; SUN JianWei
2008-01-01
In this study, experiments are carried out on the effects of magnetic fluids on the crystallization char- acterizations in a multi-component and multiphase system, which contains the liquid and the vapor of HCFC141b, water, water vapor, and gas hydrates. The mass transfer phenomena between the phase interfaces of water-HCFC141b and water-vapor are also researched. The experimental results show that in the presence of a rotary magnetic field, magnetic fluids can remarkably enhance the heat and mass transfer between phase interfaces and, therefore, improve the performance of crystallization, especially in improving the formation temperature and velocity.
Non-adiabatic perturbations in multi-component perfect fluids
Koshelev, N.A., E-mail: koshna71@inbox.ru [Ulyanovsk State University, Leo Tolstoy str 42, 432970 (Russian Federation)
2011-04-01
The evolution of non-adiabatic perturbations in models with multiple coupled perfect fluids with non-adiabatic sound speed is considered. Instead of splitting the entropy perturbation into relative and intrinsic parts, we introduce a set of symmetric quantities, which also govern the non-adiabatic pressure perturbation in models with energy transfer. We write the gauge invariant equations for the variables that determine on a large scale the non-adiabatic pressure perturbation and the rate of changes of the comoving curvature perturbation. The analysis of evolution of the non-adiabatic pressure perturbation has been made for several particular models.
Multicomponent transport in membranes for redox flow batteries
Monroe, Charles
2015-03-01
Redox flow batteries (RFBs) incorporate separator membranes, which ideally prevent mixing of electrochemically active species while permitting crossover of inactive supporting ions. Understanding crossover and membrane selectivity may require multicomponent transport models that account for solute/solute interactions within the membrane, as well as solute/membrane interactions. Application of the Onsager-Stefan-Maxwell formalism allows one to account for all the dissipative phenomena that may accompany component fluxes through RFB membranes. The magnitudes of dissipative interactions (diffusional drag forces) are quantified by matching experimentally established concentration transients with theory. Such transients can be measured non-invasively using DC conductometry, but the accuracy of this method requires precise characterization of the bulk RFB electrolytes. Aqueous solutions containing both vanadyl sulfate (VOSO4) and sulfuric acid (H2SO4) are relevant to RFB technology. One of the first precise characterizations of aqueous vanadyl sulfate has been implemented and will be reported. To assess the viability of a separator for vanadium RFB applications with cell-level simulations, it is critical to understand the tendencies of various classes of membranes to absorb (uptake) active species, and to know the relative rates of active-species and supporting-electrolyte diffusion. It is also of practical interest to investigate the simultaneous diffusion of active species and supports, because interactions between solutes may ultimately affect the charge efficiency and power efficiency of the RFB system as a whole. A novel implementation of Barnes's classical model of dialysis-cell diffusion [Physics 5:1 (1934) 4-8] is developed to measure the binary diffusion coefficients and sorption equilibria for single solutes (VOSO4 or H2SO4) in porous membranes and cation-exchange membranes. With the binary diffusion and uptake measurement in hand, a computer simulation that
Dahms, Rainer N.; Oefelein, Joseph C.
2013-09-01
A theory that explains the operating pressures where liquid injection processes transition from exhibiting classical two-phase spray atomization phenomena to single-phase diffusion-dominated mixing is presented. Imaging from a variety of experiments have long shown that under certain conditions, typically when the pressure of the working fluid exceeds the thermodynamic critical pressure of the liquid phase, the presence of discrete two-phase flow processes become diminished. Instead, the classical gas-liquid interface is replaced by diffusion-dominated mixing. When and how this transition occurs, however, is not well understood. Modern theory still lacks a physically based model to quantify this transition and the precise mechanisms that lead to it. In this paper, we derive a new model that explains how the transition occurs in multicomponent fluids and present a detailed analysis to quantify it. The model applies a detailed property evaluation scheme based on a modified 32-term Benedict-Webb-Rubin equation of state that accounts for the relevant real-fluid thermodynamic and transport properties of the multicomponent system. This framework is combined with Linear Gradient Theory, which describes the detailed molecular structure of the vapor-liquid interface region. Our analysis reveals that the two-phase interface breaks down not necessarily due to vanishing surface tension forces, but due to thickened interfaces at high subcritical temperatures coupled with an inherent reduction of the mean free molecular path. At a certain point, the combination of reduced surface tension, the thicker interface, and reduced mean free molecular path enter the continuum length scale regime. When this occurs, inter-molecular forces approach that of the multicomponent continuum where transport processes dominate across the interfacial region. This leads to a continuous phase transition from compressed liquid to supercritical mixture states. Based on this theory, a regime diagram for
Novitskiy, Alexander A; Ke, Jie; Comak, Gurbuz; Poliakoff, Martyn; George, Michael W
2011-08-01
A new continuous flow method using attenuated total reflection infrared (ATR-IR) spectroscopy has been developed for monitoring phase transitions in multicomponent fluids at high pressures and temperatures. Our approach uses Fourier transform infrared (FT-IR) and a modified Golden Gate attenuated total reflection (ATR) cell and exploits the fact that the absorbance of a vapor is much lower than that of the corresponding liquid to monitor the phase transition between vapor and liquid. We demonstrate that this method can provide quantitative measurements on both the dew point and the bubble point. We have validated our approach using three single-component systems (EtOH, MeOH, and H(2)O) and a binary system of EtOH + H(2)O, monitoring phase transitions at temperature up to 300 °C and pressure up to 10 MPa.
Saar, M. O.; Randolph, J. B.
2011-12-01
In a carbon dioxide plume geothermal (CPG) system, carbon dioxide (CO2) is pumped into existing high-permeability geologic formations that are overlain by a low-permeability caprock. The resulting CO2 plume largely displaces native formation fluid and is heated by the natural in-situ heat and background geothermal heat flux. A portion of the heated CO2 is piped to the surface to produce power and/or to provide heat for direct use before being returned to the geologic reservoir. Non-recoverable CO2 in the subsurface is geologically sequestered, serving as a CO2 sink. As such, this approach results in a geothermal power plant with a negative carbon footprint. We present results of calculations concerning geothermal power plant efficiencies and energy production rates in both traditional reservoir-based systems and engineered geothermal systems (EGS) when CO2, rather than water, is used as the subsurface working fluid. While our previous studies have examined geologic systems with established CO2 plumes, we focus here on multicomponent (CO2 + brine) systems. Numerical simulations (e.g., Randolph and Saar, Geophysical Research Letters, 2011) indicate that CPG systems provide several times the heat energy recovery of similar water-based systems. Furthermore, the CPG method results in higher geothermal heat extraction efficiencies than both water- and CO2-based EGS. Therefore, CPG should further extend the applicability of geothermal energy utilization to regions with subsurface temperatures and heat flow rates that are even lower than those that may be added due to switching from water- to CO2-based EGS. Finally, simulations at present suggest that multicomponent effects - e.g., buoyant flow as CO2 rises over denser brine - may enhance heat extraction in CPG systems compared to traditional water-based geothermal approaches.
Swati Mukhopadhyay
2013-12-01
Full Text Available The unsteady two-dimensional flow of a non-Newtonian fluid over a stretching surface having a prescribed surface temperature is investigated. The Casson fluid model is used to characterise the non-Newtonian fluid behaviour. Similarity transformations are employed to transform the governing partial differential equations into ordinary differential equations. The transformed equations are then solved numerically by shooting method. Exact solution corresponding to momentum equation for steady case is obtained. The flow features and heat transfer characteristics for different values of the governing parameters viz. unsteadiness parameter, Casson parameter and Prandtl number are analysed and discussed in detail. Fluid velocity initially decreases with increasing unsteadiness parameter and temperature decreases significantly due to unsteadiness. The effect of increasing values of the Casson parameter is to suppress the velocity field. But the temperature is enhanced with increasing Casson parameter.
Zhen-Hua Chai; Tian-Shou Zhao
2012-01-01
In this paper,a pseudopotential-based multiplerelaxation-time lattice Boltzmann model is proposed for multicomponent/multiphase flow systems.Unlike previous models in the literature,the present model not only enables the study of multicomponent flows with different molecular weights,different viscosities and different Schmidt numbers,but also ensures that the distribution function of each component evolves on the same square lattice without invoking additional interpolations.Furthermore,the Chapman-Enskog analysis shows that the present model results in the correct hydrodynamic equations,and satisfies the indifferentiability principle.The numerical validation exercises further demonstrate that the favorable performance of the present model.
Mechanistic insights into flow induced segregation in blood and other multicomponent suspensions
Kumar, Amit; Graham, Michael
2012-11-01
Blood is a multicomponent suspension comprising mostly of red-blood-cells (RBCs) along with trace amounts of leukocytes and platelets. Under normal flow conditions both the leukocytes and the platelets segregate near the vessel walls, a phenomenon commonly known as margination. The key physical differences between RBCs, leukocytes, and platelets are their relative size and rigidity: leukocytes are larger than RBCs and platelets smaller, but both are considerably stiffer than RBCs. In this work we study the blood flow problem using a model system of fluid-filled elastic capsule mixtures. Using boundary integral (BI) simulations we delineate the effect of size and rigidity on the segregation behavior, and relate these to the observations of leukocyte and platelet margination in blood. Further, we introduce a novel Monte Carlo simulation technique, which incorporates two of the key transport mechanisms in confined suspensions: the wall-induced migration and hydrodynamic pair collisions. The model accurately reproduces the results of BI simulations and provides a mechanistic understanding of the margination phenomena. In particular, it clarifies the important role of heterogeneous pair collisions (collisions between two different species) on the observed margination behavior.
Mao, X.; Prommer, H.; Barry, D.A.; Langevin, C.D.; Panteleit, B.; Li, L.
2006-01-01
PHWAT is a new model that couples a geochemical reaction model (PHREEQC-2) with a density-dependent groundwater flow and solute transport model (SEAWAT) using the split-operator approach. PHWAT was developed to simulate multi-component reactive transport in variable density groundwater flow. Fluid density in PHWAT depends not on only the concentration of a single species as in SEAWAT, but also the concentrations of other dissolved chemicals that can be subject to reactive processes. Simulation results of PHWAT and PHREEQC-2 were compared in their predictions of effluent concentration from a column experiment. Both models produced identical results, showing that PHWAT has correctly coupled the sub-packages. PHWAT was then applied to the simulation of a tank experiment in which seawater intrusion was accompanied by cation exchange. The density dependence of the intrusion and the snow-plough effect in the breakthrough curves were reflected in the model simulations, which were in good agreement with the measured breakthrough data. Comparison simulations that, in turn, excluded density effects and reactions allowed us to quantify the marked effect of ignoring these processes. Next, we explored numerical issues involved in the practical application of PHWAT using the example of a dense plume flowing into a tank containing fresh water. It was shown that PHWAT could model physically unstable flow and that numerical instabilities were suppressed. Physical instability developed in the model in accordance with the increase of the modified Rayleigh number for density-dependent flow, in agreement with previous research. ?? 2004 Elsevier Ltd. All rights reserved.
Multi-scale diffuse interface modeling of multi-component two-phase flow with partial miscibility
Kou, Jisheng
2016-05-10
In this paper, we introduce a diffuse interface model to simulate multi-component two-phase flow with partial miscibility based on a realistic equation of state (e.g. Peng-Robinson equation of state). Because of partial miscibility, thermodynamic relations are used to model not only interfacial properties but also bulk properties, including density, composition, pressure, and realistic viscosity. As far as we know, this effort is the first time to use diffuse interface modeling based on equation of state for modeling of multi-component two-phase flow with partial miscibility. In numerical simulation, the key issue is to resolve the high contrast of scales from the microscopic interface composition to macroscale bulk fluid motion since the interface has a nanoscale thickness only. To efficiently solve this challenging problem, we develop a multi-scale simulation method. At the microscopic scale, we deduce a reduced interfacial equation under reasonable assumptions, and then we propose a formulation of capillary pressure, which is consistent with macroscale flow equations. Moreover, we show that Young-Laplace equation is an approximation of this capillarity formulation, and this formulation is also consistent with the concept of Tolman length, which is a correction of Young-Laplace equation. At the macroscopical scale, the interfaces are treated as discontinuous surfaces separating two phases of fluids. Our approach differs from conventional sharp-interface two-phase flow model in that we use the capillary pressure directly instead of a combination of surface tension and Young-Laplace equation because capillarity can be calculated from our proposed capillarity formulation. A compatible condition is also derived for the pressure in flow equations. Furthermore, based on the proposed capillarity formulation, we design an efficient numerical method for directly computing the capillary pressure between two fluids composed of multiple components. Finally, numerical tests
Unsteady unidirectional micropolar fluid flow
无
2011-01-01
This paper considers the unsteady unidirectional flow of a micropolar fluid, produced by the sudden application of an arbitrary time dependent pressure gradient, between two parallel plates. The no-slip and the no-spin boundary conditions are used. Exact solutions for the velocity and microrotation distributions are obtained based on the use of the complex inversion formula of Laplace transform. The solution of the problem is also considered if the upper boundary of the flow is a free surface. The particula...
Bonilla, Mauricio R; Bhatia, Suresh K
2012-01-10
Molecular transport in nanoconfined spaces plays a key role in many emerging technologies for gas separation and storage, as well as in nanofluidics. The infiltration of fluid mixtures into the voids of porous frameworks having complex topologies is common place to these technologies, and optimizing their performance entails developing a deeper understanding of how the flow of these mixtures is affected by the morphology of the pore space, particularly its pore size distribution and pore connectivity. Although several techniques have been developed for the estimation of the effective diffusivity characterizing the transport of single fluids through porous materials, this is not the case for fluid mixtures, where the only alternatives rely on a time-consuming solution of the pore network equations or adaptations of the single fluid theories which are useful for a limited type of systems. In this paper, a hybrid multicomponent effective medium-correlated random walk theory for the calculation of the effective transport coefficients matrix of fluid mixtures diffusing through porous materials is developed. The theory is suitable for those systems in which component fluxes at the single pore level can be related to the potential gradients of the different species through linear flux laws and corresponds to a generalization of the classical single fluid effective medium theory for the analysis of random resistor networks. Comparison with simulation of the diffusion of binary CO(2)/H(2)S and ternary CO(2)/H(2)S/C(3)H(8) gas mixtures in membranes modeled as large networks of randomly oriented pores with both continuous and discrete pore size distributions demonstrates the power of the theory, which was tested using the well-known generalized Maxwell-Stefan model for surface diffusion at the single pore level.
Hermanska, M.; Stefansson, A.
2014-12-01
Many active volcanic systems are associated with high-enthalpy geothermal systems. For systems characterized by shallow magmatic intrusions, liquid water often predominates at depth with two-phase fluids, vapor and liquid water, occurring at shallower depth due to depressurization boiling. Close to the intrusion, superheated or supercritical vapor may also occur. The Krafla high-enthalpy geothermal system provides an ideal opportunity to study such volcanic geothermal systems. Over forty wells have been drilled into the system with fluid discharge temperatures of 3200 kJ/kg. In this study, geochemical modelling of multicomponent fluid phases associated with shallow magmatic intrusions were conducted across variable temperature, pressure and enthalpy conditions and the results compared with the fluid geochemistry of the Krafla system. Within the reservoir at geothermal temperatures (250-300°C) liquid water predominates. Under these conditions, the concentrations of most major elements are controlled by equilibrium with secondary minerals. Geochemical modelling and observations at Krafla support these findings. Around the magma intrusions believed to be at shallow depth at Krafla, superheated vapor is formed. Such fluid was discharged by the IDDP-1 well at 450°C and 140 bar. According to the geochemical modelling, superheated vapor is produced upon heat addition by the intrusion to the surrounding geothermal water resulting in boiling to dryness, precipitation of non-volatiles (Si, Fe, Mg, Al, SO4, Na, K, Ca) whereas volatiles (CO2, H2S, Cl, F, B) are unaffected. By mass, quartz is the predominant secondary mineral around the intrusions. The chemical composition of the modelled and observed superheated vapor compared well. Upon ascent and depressurization of the liquid geothermal water and the superheated vapor various processes may occur, including superheated vapor condensation, mixing and depressurization boiling. This leads to formation of two-phase liquid and
Multi-Component Integrable Systems and Invariant Curve Flows in Certain Geometries
Changzheng Qu
2013-01-01
Full Text Available In this paper, multi-component generalizations to the Camassa-Holm equation, the modified Camassa-Holm equation with cubic nonlinearity are introduced. Geometric formulations to the dual version of the Schrödinger equation, the complex Camassa-Holm equation and the multi-component modified Camassa-Holm equation are provided. It is shown that these equations arise from non-streching invariant curve flows respectively in the three-dimensional Euclidean geometry, the two-dimensional Möbius sphere and n-dimensional sphere S^n(1. Integrability to these systems is also studied.
Multi-Component Integrable Systems and Invariant Curve Flows in Certain Geometries
Qu, Changzheng; Song, Junfeng; Yao, Ruoxia
2013-01-01
In this paper, multi-component generalizations to the Camassa-Holm equation, the modified Camassa-Holm equation with cubic nonlinearity are introduced. Geometric formulations to the dual version of the Schrödinger equation, the complex Camassa-Holm equation and the multi-component modified Camassa-Holm equation are provided. It is shown that these equations arise from non-streching invariant curve flows respectively in the three-dimensional Euclidean geometry, the two-dimensional Möbius sphere and n-dimensional sphere Sn(1). Integrability to these systems is also studied.
A lattice Boltzmann method for axisymmetric multicomponent flows with high viscosity ratio
Liu, Haihu; Wu, Lei; Ba, Yan; Xi, Guang; Zhang, Yonghao
2016-12-01
A color-gradient lattice Boltzmann method (LBM) is proposed to simulate axisymmetric multicomponent flows. This method uses a collision operator that is a combination of three separate parts, namely single-component collision operator, perturbation operator, and recoloring operator. A source term is added into the single-component collision operator such that in each single-component region the axisymmetric continuity and momentum equations can be exactly recovered. The interfacial tension effect is realized by the perturbation operator, in which an interfacial force of axisymmetric form is derived using the concept of continuum surface force. A recoloring operator proposed by Latva-Kokko and Rothman is extended to the axisymmetric case for phase segregation and maintenance of the interface. To enhance the method's numerical stability for handling binary fluids with high viscosity ratio, a multiple-relaxation-time model is used for the collision operator. Several numerical examples, including static droplet test, oscillation of a viscous droplet, and breakup of a liquid thread, are presented to test the capability and accuracy of the proposed color-gradient LBM. It is found that the present method is able to accurately capture the phase interface and produce low spurious velocities. Also, the LBM results are all in good agreement with the analytical solutions and/or available experimental data for a very broad range of viscosity ratios.
Moortgat, Joachim; Soltanian, Mohamad Reza
2016-01-01
We present a new implicit higher-order finite element (FE) approach to efficiently model compressible multicomponent fluid flow on unstructured grids and in fractured porous subsurface formations. The scheme is sequential implicit: pressures and fluxes are updated with an implicit Mixed Hybrid Finite Element (MHFE) method, and the transport of each species is approximated with an implicit second-order Discontinuous Galerkin (DG) FE method. Discrete fractures are incorporated with a cross-flow equilibrium approach. This is the first investigation of all-implicit higher-order MHFE-DG for unstructured triangular, quadrilateral (2D), and hexahedral (3D) grids and discrete fractures. A lowest-order implicit finite volume (FV) transport update is also developed for the same grid types. The implicit methods are compared to an Implicit-Pressure-Explicit-Composition (IMPEC) scheme. For fractured domains, the unconditionally stable implicit transport update is shown to increase computational efficiency by orders of mag...
Parkhurst, David L.; Kipp, Kenneth L.; Charlton, Scott R.
2010-01-01
The computer program PHAST (PHREEQC And HST3D) simulates multicomponent, reactive solute transport in three-dimensional saturated groundwater flow systems. PHAST is a versatile groundwater flow and solute-transport simulator with capabilities to model a wide range of equilibrium and kinetic geochemical reactions. The flow and transport calculations are based on a modified version of HST3D that is restricted to constant fluid density and constant temperature. The geochemical reactions are simulated with the geochemical model PHREEQC, which is embedded in PHAST. Major enhancements in PHAST Version 2 allow spatial data to be defined in a combination of map and grid coordinate systems, independent of a specific model grid (without node-by-node input). At run time, aquifer properties are interpolated from the spatial data to the model grid; regridding requires only redefinition of the grid without modification of the spatial data. PHAST is applicable to the study of natural and contaminated groundwater systems at a variety of scales ranging from laboratory experiments to local and regional field scales. PHAST can be used in studies of migration of nutrients, inorganic and organic contaminants, and radionuclides; in projects such as aquifer storage and recovery or engineered remediation; and in investigations of the natural rock/water interactions in aquifers. PHAST is not appropriate for unsaturated-zone flow, multiphase flow, or density-dependent flow. A variety of boundary conditions are available in PHAST to simulate flow and transport, including specified-head, flux (specified-flux), and leaky (head-dependent) conditions, as well as the special cases of rivers, drains, and wells. Chemical reactions in PHAST include (1) homogeneous equilibria using an ion-association or Pitzer specific interaction thermodynamic model; (2) heterogeneous equilibria between the aqueous solution and minerals, ion exchange sites, surface complexation sites, solid solutions, and gases; and
Meroni, Andrea; Andreasen, Jesper Graa; Pierobon, Leonardo;
2016-01-01
engine onboard a large ship, and the latter is representative of a low-temperature geothermal, solar or waste heat recovery application. Multi-component working fluids are investigated, as they allow improving the match between the temperature pro-files in the heat exchangers and, consequently, reducing...
Viscous Flow with Large Fluid-Fluid Interface Displacement
Rasmussen, Henrik Koblitz; Hassager, Ole; Saasen, Arild
1998-01-01
The arbitrary Lagrange-Euler (ALE) kinematic description has been implemented in a 3D transient finite element program to simulate multiple fluid flows with fluid-fluid interface or surface displacements. The description of fluid interfaces includes variable interfacial tension, and the formulation...
Phase Equilibrium Calculations for Multi-Component Polar Fluid Mixtures with tPC-PSAFT
Karakatsani, Eirini; Economou, Ioannis
2007-01-01
The truncated Perturbed-Chain Polar Statistical Associating Fluid Theory (tPC-PSAFT) is applied to a number of different mixtures, including binary, ternary and quaternary mixtures of components that differ substantially in terms of intermolecular interactions and molecular size. In contrast...... to most other SAFT versions, tPC-PSAFT accounts explicitly for polar forces. Three pure-component parameters are required for non-polar and non-associating compounds, two additional parameters characterize the association contribution and one parameter is needed to account for polar interactions....... The experimental dipole and/or quadrupole moment and/or polarizability of the component are used to calculate polar interactions. Using a temperature-independent interaction parameter kij for each binary system, tPC-PSAFT provides accurate prediction of multi-component phase behavior over a wide range...
Hammond, Glenn E.; Lichtner, Peter C.; Lu, Chuan
2007-08-01
Numerical modeling has become a critical tool to the Department of Energy for evaluating the environmental impact of alternative energy sources and remediation strategies for legacy waste sites. Unfortunately, the physical and chemical complexity of many sites overwhelms the capabilities of even most “state of the art” groundwater models. Of particular concern are the representation of highly-heterogeneous stratified rock/soil layers in the subsurface and the biological and geochemical interactions of chemical species within multiple fluid phases. Clearly, there is a need for higher-resolution modeling (i.e. more spatial, temporal, and chemical degrees of freedom) and increasingly mechanistic descriptions of subsurface physicochemical processes. We present research being performed in the development of PFLOTRAN, a parallel multiphase flow and multicomponent reactive transport model. Written in Fortran90, PFLOTRAN is founded upon PETSc data structures and solvers and has exhibited impressive strong scalability on up to 4000 processors on the ORNL Cray XT3. We are employing PFLOTRAN in the simulation of uranium transport at the Hanford 300 Area, a contaminated site of major concern to the Department of Energy, the State of Washington, and other government agencies where overly-simplistic historical modeling erroneously predicted decade removal times for uranium by ambient groundwater flow. By leveraging the billions of degrees of freedom available through high-performance computation using tens of thousands of processors, we can better characterize the release of uranium into groundwater and its subsequent transport to the Columbia River, and thereby better understand and evaluate the effectiveness of various proposed remediation strategies.
Kou, Jisheng
2015-08-01
Surface tension significantly impacts subsurface flow and transport, and it is the main cause of capillary effect, a major immiscible two-phase flow mechanism for systems with a strong wettability preference. In this paper, we consider the numerical simulation of the surface tension of multi-component mixtures with the gradient theory of fluid interfaces. Major numerical challenges include that the system of the Euler-Lagrange equations is solved on the infinite interval and the coefficient matrix is not positive definite. We construct a linear transformation to reduce the Euler-Lagrange equations, and naturally introduce a path function, which is proven to be a monotonic function of the spatial coordinate variable. By using the linear transformation and the path function, we overcome the above difficulties and develop the efficient methods for calculating the interface and its interior compositions. Moreover, the computation of the surface tension is also simplified. The proposed methods do not need to solve the differential equation system, and they are easy to be implemented in practical applications. Numerical examples are tested to verify the efficiency of the proposed methods. © 2014 Elsevier B.V.
Katyal, A. K.; Kaluarachchi, J. J.; Parker, J. C.
1991-05-01
The manual describes a two-dimensional finite element model for coupled multiphase flow and multicomponent transport in planar or radially symmetric vertical sections. Flow and transport of three fluid phases, including water, nonaqueous phase liquid (NAPL), and gas are considered by the program. The program can simulate flow only or coupled flow and transport. The flow module can be used to analyze two phases, water and NAPL, with the gas phase held at constant pressure, or explicit three-phase flow of water, NAPL, and gas at various pressures. The transport module can handle up to five components which partition among water, NAPL, gas and solid phases assuming either local equilibrium or first-order mass transfer. Three phase permeability-saturation-capillary pressure relations are defined by an extension of the van Genuchten model. The governing equations are solved using an efficient upstream-weighted finite element scheme. The required inputs for flow and transport analysis are described. Detailed instructions for creating data files needed to run the program and examples of input and output files are given in appendices.
Flow of polymer fluids through porous media
Zami-Pierre, Frédéric; Davit, Yohan; Loubens, Romain de; Quintard, Michel
2016-01-01
Non-Newtonian fluids are extensively used in enhanced oil recovery. However, understanding the flow of such fluids in complex porous media remains a challenging problem. In the presented study, we use computational fluid dynamics to investigate the creeping flow of a particular non-Newtonian fluid through porous media, namely a power-law fluid with a newtonian behavior below a critical shear rate. We show that the nonlinear effects induced by the rheology only weakly impact the topological st...
Many-body dissipative particle dynamics modeling of fluid flow in fine-grained nanoporous shales
Xia, Yidong; Goral, Jan; Huang, Hai; Miskovic, Ilija; Meakin, Paul; Deo, Milind
2017-05-01
A many-body dissipative particle dynamics model, namely, MDPD, is applied for simulation of pore-scale, multi-component, multi-phase fluid flows in fine-grained, nanoporous shales. Since this model is able to simultaneously capture the discrete features of fluid molecules in nanometer size pores and continuum fluid dynamics in larger pores, and is relatively easy to parameterize, it has been recognized as being particularly suitable for simulating complex fluid flow in multi-length-scale nanopore networks of shales. A remarkable feature of this work is the integration of a high-resolution FIB-SEM (focused ion beam scanning electron microscopy) digital imaging technique to the MDPD model for providing 3D voxel data that contain the invaluable geometrical and compositional information of shale samples. This is the first time that FIB-SEM is seamlessly linked to a Lagrangian model like MDPD for fluid flow simulation, which offers a robust approach to bridging gaps between the molecular- and continuum-scales, since the relevant spatial and temporal scales are too big for molecular dynamics, and too small for computational fluid dynamics with known constitutive models. Simulations ranging from a number of benchmark problems to a forced two-fluid flow in a Woodford shale sample are presented. Results indicate that this model can be used to deliver reasonable simulations for multi-component, multi-phase fluid flows in arbitrarily complex pore networks in shales.
LATTICE BOLTZMANN METHOD SIMULATION ON THE FLOW OF TWO IMMISCIBLE FLUIDS IN COMPLEX GEOMETRY
Fang Hai-ping; Wan Rong-zheng; Fan Le-wen
2000-01-01
The multicomponent nonideal gas lattice Boltzmann model byShan and Chen (S-C) can be used to simulate the immiscible fluidflow. In this paper, weshow that the relaxation constant 1 is a necessarycondition for the immiscible fluid flow in the S-C model. In asystem with very complex boundary geometry, for 0.8 1, the S-C model describes the immiscible flow quite well, and=1 is the best.
Steady laminar flow of fractal fluids
Balankin, Alexander S.; Mena, Baltasar; Susarrey, Orlando; Samayoa, Didier
2017-02-01
We study laminar flow of a fractal fluid in a cylindrical tube. A flow of the fractal fluid is mapped into a homogeneous flow in a fractional dimensional space with metric induced by the fractal topology. The equations of motion for an incompressible Stokes flow of the Newtonian fractal fluid are derived. It is found that the radial distribution for the velocity in a steady Poiseuille flow of a fractal fluid is governed by the fractal metric of the flow, whereas the pressure distribution along the flow direction depends on the fractal topology of flow, as well as on the fractal metric. The radial distribution of the fractal fluid velocity in a steady Couette flow between two concentric cylinders is also derived.
Parkhurst, David L.; Kipp, Kenneth L.; Engesgaard, Peter; Charlton, Scott R.
2004-01-01
The computer program PHAST simulates multi-component, reactive solute transport in three-dimensional saturated ground-water flow systems. PHAST is a versatile ground-water flow and solute-transport simulator with capabilities to model a wide range of equilibrium and kinetic geochemical reactions. The flow and transport calculations are based on a modified version of HST3D that is restricted to constant fluid density and constant temperature. The geochemical reactions are simulated with the geochemical model PHREEQC, which is embedded in PHAST. PHAST is applicable to the study of natural and contaminated ground-water systems at a variety of scales ranging from laboratory experiments to local and regional field scales. PHAST can be used in studies of migration of nutrients, inorganic and organic contaminants, and radionuclides; in projects such as aquifer storage and recovery or engineered remediation; and in investigations of the natural rock-water interactions in aquifers. PHAST is not appropriate for unsaturated-zone flow, multiphase flow, density-dependent flow, or waters with high ionic strengths. A variety of boundary conditions are available in PHAST to simulate flow and transport, including specified-head, flux, and leaky conditions, as well as the special cases of rivers and wells. Chemical reactions in PHAST include (1) homogeneous equilibria using an ion-association thermodynamic model; (2) heterogeneous equilibria between the aqueous solution and minerals, gases, surface complexation sites, ion exchange sites, and solid solutions; and (3) kinetic reactions with rates that are a function of solution composition. The aqueous model (elements, chemical reactions, and equilibrium constants), minerals, gases, exchangers, surfaces, and rate expressions may be defined or modified by the user. A number of options are available to save results of simulations to output files. The data may be saved in three formats: a format suitable for viewing with a text editor; a
Streamwise transport in multi-component granular flows
Johnson, Chris; Hogg, Andrew; Phillips, Jeremy
2016-11-01
Thin free-surface avalanches of granular material occur widely in nature and industry. In these contexts the flows often contain particles of a wide range of sizes, which separate from one another due to particle size segregation. This segregation is troublesome in industry (where a well-mixed state is usually desired) and is an important mechanism for determining the runout and morphology of natural avalanches and debris flows. In this talk we develop a model for the spatial and temporal evolution of the particle size distribution in a granular flow, due to particle segregation, diffusion and advection processes. We use asymptotic solutions of this model to formulate equations governing the depth-integrated particle size distribution. These equations naturally extend the shallow-water models often used to predict the dynamics of monodisperse avalanches. Our modelling shows that particles in granular avalanches may strongly segregate in the direction of flow, even when the segregation is relatively weak compared to diffusive mixing and the avalanche is nearly homogeneous throughout its depth. We demonstrate this surprising phenomenon through comparison with discrete particle simulations.
Fluid Flow Experiment for Undergraduate Laboratory.
Vilimpochapornkul, Viroj; Obot, Nsima T.
1986-01-01
The undergraduate fluid mechanics laboratory at Clarkson University consists of three experiments: mixing; drag measurements; and fluid flow and pressure drop measurements. The latter experiment is described, considering equipment needed, procedures used, and typical results obtained. (JN)
Steady laminar flow of fractal fluids
Balankin, Alexander S., E-mail: abalankin@ipn.mx [Grupo Mecánica Fractal, ESIME, Instituto Politécnico Nacional, México D.F., 07738 (Mexico); Mena, Baltasar [Laboratorio de Ingeniería y Procesos Costeros, Instituto de Ingeniería, Universidad Nacional Autónoma de México, Sisal, Yucatán, 97355 (Mexico); Susarrey, Orlando; Samayoa, Didier [Grupo Mecánica Fractal, ESIME, Instituto Politécnico Nacional, México D.F., 07738 (Mexico)
2017-02-12
We study laminar flow of a fractal fluid in a cylindrical tube. A flow of the fractal fluid is mapped into a homogeneous flow in a fractional dimensional space with metric induced by the fractal topology. The equations of motion for an incompressible Stokes flow of the Newtonian fractal fluid are derived. It is found that the radial distribution for the velocity in a steady Poiseuille flow of a fractal fluid is governed by the fractal metric of the flow, whereas the pressure distribution along the flow direction depends on the fractal topology of flow, as well as on the fractal metric. The radial distribution of the fractal fluid velocity in a steady Couette flow between two concentric cylinders is also derived. - Highlights: • Equations of Stokes flow of Newtonian fractal fluid are derived. • Pressure distribution in the Newtonian fractal fluid is derived. • Velocity distribution in Poiseuille flow of fractal fluid is found. • Velocity distribution in a steady Couette flow is established.
EXACT SOLUTIONS OF A DIPOLAR FLUID FLOW
T. HAYAT
2003-01-01
Exact solutions for three canonical flow problems of a dipolar fluid are obtained: (i)The flow of a dipolar fluid due to a suddenly accelerated plate, (ii) The flow generated by periodic oscillation of a plate, (iii) The flow due to plate oscillation in the presence of a transverse magnetic field. The solutions of some interesting flows caused by an arbitrary velocity of the plate and of certain special oscillations are also obtained.
Meroni, Andrea; Andreasen, Jesper Graa; Pierobon, Leonardo
2016-01-01
the irreversibility in the ORC system. This work considers mixtures of R245fa/pentane and propane/isobutane. The use of multi-component working fluids typically results in increased heat transfer areas and different expander designs compared to purefluids. In order to properly account for turbine performance...... for an organic Rankine cycle unit utilizing waste heat from low temperature heat sources. The study addresses a case where the minimum temperature of the heat source is constrained and a case where no constraint is imposed. The former case is the wasteheat recovery from jacket cooling water of a marine diesel...... engine onboard a large ship, and the latter is representative of a low-temperature geothermal, solar or waste heat recovery application. Multi-component working fluids are investigated, as they allow improving the match between the temperature pro-files in the heat exchangers and, consequently, reducing...
Moortgat, Joachim; Amooie, Mohammad Amin; Soltanian, Mohamad Reza
2016-10-01
We present a new implicit higher-order finite element (FE) approach to efficiently model compressible multicomponent fluid flow on unstructured grids and in fractured porous subsurface formations. The scheme is sequential implicit: pressures and fluxes are updated with an implicit Mixed Hybrid Finite Element (MHFE) method, and the transport of each species is approximated with an implicit second-order Discontinuous Galerkin (DG) FE method. Discrete fractures are incorporated with a cross-flow equilibrium approach. This is the first investigation of all-implicit higher-order MHFE-DG for unstructured triangular, quadrilateral (2D), and hexahedral (3D) grids and discrete fractures. A lowest-order implicit finite volume (FV) transport update is also developed for the same grid types. The implicit methods are compared to an Implicit-Pressure-Explicit-Composition (IMPEC) scheme. For fractured domains, the unconditionally stable implicit transport update is shown to increase computational efficiency by orders of magnitude as compared to IMPEC, which has a time-step constraint proportional to the pore volume of discrete fracture grid cells. However, when lowest-order Euler time-discretizations are used, numerical errors increase linearly with the larger implicit time-steps, resulting in high numerical dispersion. Second-order Crank-Nicolson implicit MHFE-DG and MHFE-FV are therefore presented as well. Convergence analyses show twice the convergence rate for the DG methods as compared to FV, resulting in two to three orders of magnitude higher computational efficiency. Numerical experiments demonstrate the efficiency and robustness in modeling compressible multicomponent flow on irregular and fractured 2D and 3D grids, even in the presence of fingering instabilities.
Introduction to compressible fluid flow
Oosthuizen, Patrick H
2013-01-01
IntroductionThe Equations of Steady One-Dimensional Compressible FlowSome Fundamental Aspects of Compressible FlowOne-Dimensional Isentropic FlowNormal Shock WavesOblique Shock WavesExpansion Waves - Prandtl-Meyer FlowVariable Area FlowsAdiabatic Flow with FrictionFlow with Heat TransferLinearized Analysis of Two-Dimensional Compressible FlowsHypersonic and High-Temperature FlowsHigh-Temperature Gas EffectsLow-Density FlowsBibliographyAppendices
Kou, Jisheng
2016-01-01
A general diffuse interface model with a realistic equation of state (e.g. Peng-Robinson equation of state) is proposed to describe the multi-component two-phase fluid flow based on the principles of the NVT-based framework which is a latest alternative over the NPT-based framework to model the realistic fluids. The proposed model uses the Helmholtz free energy rather than Gibbs free energy in the NPT-based framework. Different from the classical routines, we combine the first law of thermodynamics and related thermodynamical relations to derive the entropy balance equation, and then we derive a transport equation of the Helmholtz free energy density. Furthermore, by using the second law of thermodynamics, we derive a set of unified equations for both interfaces and bulk phases that can describe the partial miscibility of two fluids. A relation between the pressure gradient and chemical potential gradients is established, and this relation leads to a new formulation of the momentum balance equation, which dem...
Computational fluid dynamics incompressible turbulent flows
Kajishima, Takeo
2017-01-01
This textbook presents numerical solution techniques for incompressible turbulent flows that occur in a variety of scientific and engineering settings including aerodynamics of ground-based vehicles and low-speed aircraft, fluid flows in energy systems, atmospheric flows, and biological flows. This book encompasses fluid mechanics, partial differential equations, numerical methods, and turbulence models, and emphasizes the foundation on how the governing partial differential equations for incompressible fluid flow can be solved numerically in an accurate and efficient manner. Extensive discussions on incompressible flow solvers and turbulence modeling are also offered. This text is an ideal instructional resource and reference for students, research scientists, and professional engineers interested in analyzing fluid flows using numerical simulations for fundamental research and industrial applications. • Introduces CFD techniques for incompressible flow and turbulence with a comprehensive approach; • Enr...
Hydromagnetic rotating flow of third grade fluid
T. HAYAT; R. NAZ; A. ALSAEDI; M. M. RASHIDI
2013-01-01
This work investigates the flow of a third grade fluid in a rotating frame of reference. The fluid is incompressible and magnetohydrodynamic (MHD). The flow is bounded between two porous plates, the lower of which is shrinking linearly. Mathematical modelling of the considered flow leads to a nonlinear problem. The solution of this nonlinear problem is computed by the homotopy analysis method (HAM). Graphs are presented to demonstrate the effect of several emerging parameters, which clearly describe the flow characteristics.
Mathematical theory of compressible fluid flow
Von Mises, Richard
2012-01-01
Mathematical Theory of Compressible Fluid Flow covers the conceptual and mathematical aspects of theory of compressible fluid flow. This five-chapter book specifically tackles the role of thermodynamics in the mechanics of compressible fluids. This text begins with a discussion on the general theory of characteristics of compressible fluid with its application. This topic is followed by a presentation of equations delineating the role of thermodynamics in compressible fluid mechanics. The discussion then shifts to the theory of shocks as asymptotic phenomena, which is set within the context of
Oostrom, Martinus; Zhang, Z. F.; Freedman, Vicky L.; Tartakovsky, Guzel D.
2008-09-29
Carbon tetrachloride (CT) was discharged to waste sites that are included in the 200-PW-1 Operable Unit in Hanford 200 West Area. Fluor Hanford, Inc. is conducting a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) remedial investigation/feasibility study (RI/FS) for the 200-PW-1 Operable Unit. The RI/FS process and remedial investigations for the 200-PW-1, 200 PW-3, and 200-PW-6 Operable Units are described in the Plutonium/Organic-Rich Process Condensate/Process Waste Groups Operable Unit RI/FS Work Plan. As part of this overall effort, Pacific Northwest National Laboratory (PNNL) was contracted to improve the STOMP simulator (White and Oostrom, 2006) by incorporating kinetic volatilization of nonaqueous phase liquids (NAPL) and multicomponent flow and transport. This work supports the U.S. Department of Energy's (DOE's) efforts to characterize the nature and distribution of CT in the 200 West Area and subsequently select an appropriate final remedy. Previous numerical simulation results with the STOMP simulator have overestimated the effect of soil vapor extraction (SVE) on subsurface CT, showing rapid removal of considerably more CT than has actually been recovered so far. These previous multiphase simulations modeled CT mass transfer between phases based on equilibrium partitioning. Equilibrium volatilization can overestimate volatilization because mass transfer limitations present in the field are not considered. Previous simulations were also conducted by modeling the NAPL as a single component, CT. In reality, however, the NAPL mixture disposed of at the Hanford site contained several non-volatile and nearly insoluble organic components, resulting in time-variant fluid properties as the CT component volatilized or dissolved over time. Simulation of CT removal from a DNAPL mixture using single-component DNAPL properties typically leads to an overestimation of CT removal. Other possible reasons for the discrepancy
AEROFROSH: a shock condition calculator for multi-component fuel aerosol-laden flows
Campbell, M. F.; Haylett, D. R.; Davidson, D. F.; Hanson, R. K.
2016-07-01
This article introduces an algorithm that determines the thermodynamic conditions behind incident and reflected shocks in aerosol-laden flows. Importantly, the algorithm accounts for the effects of droplet evaporation on post-shock properties. Additionally, this article describes an algorithm for resolving the effects of multiple-component-fuel droplets. This article presents the solution methodology and compares the results to those of another similar shock calculator. It also provides examples to show the impact of droplets on post-shock properties and the impact that multi-component fuel droplets have on shock experimental parameters. Finally, this paper presents a detailed uncertainty analysis of this algorithm's calculations given typical experimental uncertainties.
Bifurcated SEN with Fluid Flow Conditioners
F. Rivera-Perez
2014-01-01
Full Text Available This work evaluates the performance of a novel design for a bifurcated submerged entry nozzle (SEN used for the continuous casting of steel slabs. The proposed design incorporates fluid flow conditioners attached on SEN external wall. The fluid flow conditioners impose a pseudosymmetric pattern in the upper zone of the mold by inhibiting the fluid exchange between the zones created by conditioners. The performance of the SEN with fluid flow conditioners is analyzed through numerical simulations using the CFD technique. Numerical results were validated by means of physical simulations conducted on a scaled cold water model. Numerical and physical simulations confirmed that the performance of the proposed SEN is superior to a traditional one. Fluid flow conditioners reduce the liquid free surface fluctuations and minimize the occurrence of vortexes at the free surface.
Khattri, Sanjay Kumar
2006-07-01
The thesis is concerned with numerically simulating multicomponent, multiphase, reactive transport in heterogeneous porous medium. Such processes are ubiquitous, for example, deposition of green house gases, flow of hydrocarbons and groundwater remediation. Understanding such processes is important from social and economic point of view. For the success of geological sequestration, an accurate estimation of migration patterns of green-house gases is essential. Due to an ever increasing computer power, computational mathematics has become an important tool for predicting dynamics of porous media fluids. Numerical and mathematical modelling of processes in a domain requires grid generation in the domain, discretization of the continuum equations on the generated grid, solution of the formed linear or nonlinear system of discrete equations and finally visualization of the results. The thesis is composed of three chapters and eight papers. Chapter 2 presents two techniques for generating structured quadrilateral and hexahedral meshes. These techniques are called algebraic and elliptic methods. Algebraic techniques are by far the most simple and computationally efficient method for grid generation. Transfinite interpolation operators are a kind of algebraic grid generation technique. In this chapter, many transfinite interpolation operators for grid generation are derived from 1D projection operators. In this chapter, some important properties of hexahedral elements are also mentioned. These properties are useful in discretization of partial differential equations on hexahedral mesh, improving quality of the hexahedral mesh, mesh generation and visualization. Chapter 3 is about CO{sub 2} flow in porous media. In this chapter, we present the mathematical models and their discretization for capturing major physical processes associated with CO{sub 2} deposition in geological formations. Some important simulations of practical applications in 2D and 3D are presented
Khattri, Sanjay Kumar
2006-07-01
The thesis is concerned with numerically simulating multicomponent, multiphase, reactive transport in heterogeneous porous medium. Such processes are ubiquitous, for example, deposition of green house gases, flow of hydrocarbons and groundwater remediation. Understanding such processes is important from social and economic point of view. For the success of geological sequestration, an accurate estimation of migration patterns of green-house gases is essential. Due to an ever increasing computer power, computational mathematics has become an important tool for predicting dynamics of porous media fluids. Numerical and mathematical modelling of processes in a domain requires grid generation in the domain, discretization of the continuum equations on the generated grid, solution of the formed linear or nonlinear system of discrete equations and finally visualization of the results. The thesis is composed of three chapters and eight papers. Chapter 2 presents two techniques for generating structured quadrilateral and hexahedral meshes. These techniques are called algebraic and elliptic methods. Algebraic techniques are by far the most simple and computationally efficient method for grid generation. Transfinite interpolation operators are a kind of algebraic grid generation technique. In this chapter, many transfinite interpolation operators for grid generation are derived from 1D projection operators. In this chapter, some important properties of hexahedral elements are also mentioned. These properties are useful in discretization of partial differential equations on hexahedral mesh, improving quality of the hexahedral mesh, mesh generation and visualization. Chapter 3 is about CO{sub 2} flow in porous media. In this chapter, we present the mathematical models and their discretization for capturing major physical processes associated with CO{sub 2} deposition in geological formations. Some important simulations of practical applications in 2D and 3D are presented
Computation of two-fluid, flowing equilibria
Steinhauer, Loren; Kanki, Takashi; Ishida, Akio
2006-10-01
Equilibria of flowing two-fluid plasmas are computed for realistic compact-toroid and spherical-tokamak parameters. In these examples the two-fluid parameter ɛ (ratio of ion inertial length to overall plasma size) is small, ɛ ˜ 0.03 -- 0.2, but hardly negligible. The algorithm is based on the nearby-fluids model [1] which avoids a singularity that otherwise occurs for small ɛ. These representative equilibria exhibit significant flows, both toroidal and poloidal. Further, the flow patterns display notable flow shear. The importance of two-fluid effects is demonstrated by comparing with analogous equilibria (e.g. fixed toroidal and poloidal current) for a static plasma (Grad-Shafranov solution) and a flowing single-fluid plasma. Differences between the two-fluid, single-fluid, and static equilibria are highlighted: in particular with respect to safety factor profile, flow patterns, and electrical potential. These equilibria are computed using an iterative algorithm: it employs a successive-over-relaxation procedure for updating the magnetic flux function and a Newton-Raphson procedure for updating the density. The algorithm is coded in Visual Basic in an Excel platform on a personal computer. The computational time is essentially instantaneous (seconds). [1] L.C. Steinhauer and A. Ishida, Phys. Plasmas 13, 052513 (2006).
Fluid Mechanics An Introduction to the Theory of Fluid Flows
Durst, Franz
2008-01-01
Advancements of fluid flow measuring techniques and of computational methods have led to new ways to treat laminar and turbulent flows. These methods are extensively used these days in research and engineering practise. This also requires new ways to teach the subject to students at higher educational institutions in an introductory manner. The book provides the knowledge to students in engineering and natural science needed to enter fluid mechanics applications in various fields. Analytical treatments are provided, based on the Navier-Stokes equations. Introductions are also given into numerical and experimental methods applied to flows. The main benefit the reader will derive from the book is a sound introduction into all aspects of fluid mechanics covering all relevant subfields.
A review of interaction mechanisms in fluid-solid flows
Johnson, G.; Rajagopal, K.R. (Pittsburgh Univ., PA (USA). Dept. of Mechanical Engineering); Massoudi, M. (USDOE Pittsburgh Energy Technology Center, PA (USA))
1990-09-01
Multiphase flows have become the subject of considerable attention because of their importance in many industrial applications, such as fluidized beds, pneumatic transport of solids, coal combustion, etc. Fundamental research into the nature of pneumatic transport has made significant progress in identifying key parameters controlling the characteristics of these processes. The emphasis of this study is on a mixture composed of spherical particles of uniform size and a linearly viscous fluid. Section 1 introduces our approach and the importance of this study. In Section 2, the dynamics of a single particle as studied in classical hydrodynamics and fluid dynamics is presented. This has been a subject of study for more than 200 years. In Section 3, we review the literature for the constitutive relations as given in multiphase studies, i.e., generalization of single particle and as given in literature concerning the continuum theories of mixtures or multicomponent systems. In Section 4, a comparison between these representations and the earlier approach, i.e., forces acting on a single particle will be made. The importance of flow regimes, particle concentration, particle size and shape, rotation of the particle, effect of solid walls, etc. are discussed. 141 refs.
Fluid flow control with transformation media
Urzhumov, Yaroslav A
2011-01-01
We introduce a new concept for the manipulation of fluid flow around three-dimensional bodies. Inspired by transformation optics, the concept is based on a mathematical idea of coordinate transformations, and physically implemented with anisotropic porous media permeable to the flow of fluids. In two different situations - for an impermeable object situated either in a free-flowing fluid or in a fluid-filled porous medium - we show that the object can be coated with a properly chosen inhomogeneous, anisotropic permeable medium, such as to preserve the streamlines of flow and the pressure distribution that would have existed in the absence of the object. The proposed fluid flow cloak completely eliminates any disturbance of the flow by the object, including the downstream wake. Consequently, the structure helps prevent the onset of turbulence by keeping the flow laminar even above the typical critical Reynolds number for the object of the same shape and size. The cloak also cancels the viscous drag force. This...
Mechanics of coupled granular/fluid flows
Vinningland, J.; Toussaint, R.; Johnsen, O.; Flekkoy, E. G.; Maloy, K. J.
2006-12-01
We introduce a hybrid numerical model for coupled flow of solid grains and intersticial fluid, which renders for complex hydrodynamic interactions between mobile grains. This model treats the solid phase as discrete particles, interacting mechanically with the other particles and with the intersticial flowing fluid. The fluid is described by continuum equations rendering for its advection by the local grains, superposed to a pressure diffusion ruled by a Darcy flow with a permeability depending on the local solid fraction. This model is aimed at describing accurately such coupled flow. This model is tested for two model situations, where it is compared to experimental results: 1/ Injection of a localized overpressure in a grain/fluid filled cell lying horizontally, where gravity is unimportant. 2/ Sedimentation of heavy grains falling into an initially grain-free fluid region. The development of pattern-forming instabilities is obtained in these two situations, corresponding to granular/fluid equivalents of the two-fluids Saffman-Taylor and Rayleigh-Taylor instabilities. Numerical and experimental results are shown to be consistent with each other.
vanVlimmeren, BAC; Fraaije, JGEM
1996-01-01
We present a simple method for the numerical calculation of the noise distribution in multicomponent functional Langevin models. The topic is of considerable importance, in view of the increased interest in the application of mesoscopic dynamics simulation models to phase separation of complex
Apparatus for measuring fluid flow
Smith, J.E.; Thomas, D.G.
Flow measuring apparatus includes a support loop having strain gages mounted thereon and a drag means which is attached to one end of the support loop and which bends the sides of the support loop and induces strains in the strain gages when a flow stream impacts thereon.
Simulation based engineering in fluid flow design
Rao, J S
2017-01-01
This volume offers a tool for High Performance Computing (HPC). A brief historical background on the subject is first given. Fluid Statics dealing with Pressure in fluids at rest, Buoyancy and Basics of Thermodynamics are next presented. The Finite Volume Method, the most convenient process for HPC, is explained in one-dimensional approach to diffusion with convection and pressure velocity coupling. Adiabatic, isentropic and supersonic flows in quasi-one dimensional flows in axisymmetric nozzles is considered before applying CFD solutions. Though the theory is restricted to one-dimensional cases, three-dimensional CFD examples are also given. Lastly, nozzle flows with normal shocks are presented using turbulence models. Worked examples and exercises are given in each chapter. Fluids transport thermal energy for its conversion to kinetic energy, thus playing a major role that is central to all heat engines. With the advent of rotating machinery in the 20th century, Fluid Engineering was developed in the form o...
Sin, Irina; Lagneau, Vincent; Corvisier, Jérôme
2017-02-01
This work aims to incorporate compressible multiphase flow into the conventional reactive transport framework using an operator splitting approach. This new approach would allow us to retain the general paradigm of the flow module independent of the geochemical processes and to model complex multiphase chemical systems, conserving the versatile structure of conventional reactive transport. The phase flow formulation is employed to minimize the number of mass conservation nonlinear equations arising from the flow module. Applying appropriate equations of state facilitated precise descriptions of the compressible multicomponent phases, their thermodynamic properties and relevant fluxes. The proposed flow coupling method was implemented in the reactive transport software HYTEC. The entire framework preserves its flexibility for further numerical developments. The verification of the coupling was achieved by modeling a problem with a self-similar solution. The simulation of a 2D CO2-injection problem demonstrates the pertinent physical results and computational efficiency of this method. The coupling method was employed for modeling injection of acid gas mixture in carbonated reservoir.
Tracer technology modeling the flow of fluids
Levenspiel, Octave
2012-01-01
A vessel’s behavior as a heat exchanger, absorber, reactor, or other process unit is dependent upon how fluid flows through the vessel. In early engineering, the designer would assume either plug flow or mixed flow of the fluid through the vessel. However, these assumptions were oftentimes inaccurate, sometimes being off by a volume factor of 100 or more. The result of this unreliable figure produced ineffective products in multiple reaction systems. Written by a pioneering researcher in the field of chemical engineering, the tracer method was introduced to provide more accurate flow data. First, the tracer method measured the actual flow of fluid through a vessel. Second, it developed a suitable model to represent the flow in question. Such models are used to follow the flow of fluid in chemical reactors and other process units, like in rivers and streams, or solid and porous structures. In medicine, the tracer method is used to study the flow of chemicals—harmful and harmless—in the...
Fluid flow in carbon nanotubes and nanopipes
Whitby, M.; Quirke, N.
2007-02-01
Nanoscale carbon tubes and pipes can be readily fabricated using self-assembly techniques and they have useful electrical, optical and mechanical properties. The transport of liquids along their central pores is now of considerable interest both for testing classical theories of fluid flow at the nanoscale and for potential nanofluidic device applications. In this review we consider evidence for novel fluid flow in carbon nanotubes and pipes that approaches frictionless transport. Methods for controlling such flow and for creating functional device architectures are described and possible applications are discussed.
Mathematical theory of compressible fluid flow
von Mises, Richard
2004-01-01
A pioneer in the fields of statistics and probability theory, Richard von Mises (1883-1953) made notable advances in boundary-layer-flow theory and airfoil design. This text on compressible flow, unfinished upon his sudden death, was subsequently completed in accordance with his plans, and von Mises' first three chapters were augmented with a survey of the theory of steady plane flow. Suitable as a text for advanced undergraduate and graduate students - as well as a reference for professionals - Mathematical Theory of Compressible Fluid Flow examines the fundamentals of high-speed flows, with
Topology of helical fluid flow
Andersen, Morten; Brøns, Morten
2014-01-01
the zeroes of a single real function of one variable, and we show that three different flow topologies can occur, depending on a single dimensionless parameter. By including the self-induced velocity on the vortex filament by a localised induction approximation, the stream function is slightly modified...
Unsteady fluid flow in smart material actuated fluid pumps
John, Shaju; Cadou, Christopher
2005-05-01
Smart materials' ability to deliver large block forces in a small package while operating at high frequencies makes them extremely attractive for converting electrical to mechanical power. This has led to the development of hybrid actuators consisting of co-located smart material actuated pumps and hydraulic cylinders that are connected by a set of fast-acting valves. The overall success of the hybrid concept hinges on the effectiveness of the coupling between the smart material and the fluid. This, in turn, is strongly dependent on the resistance to fluid flow in the device. This paper presents results from three-dimensional unsteady simulations of fluid flow in the pumping chamber of a prototype hybrid actuator powered by a piezo-electric stack. The results show that the forces associated with moving the fluid into and out of the pumping chamber already exceed 10% of the piezo stack blocked force at relatively low frequencies ~120 Hz and approach 40% of the blocked force at 800 Hz. This reduces the amplitude of the piston motion in such a way that the volume flow rate remains approximately constant above operating frequencies of 500 Hz while the efficiency of the pump decreases rapidly.
Kamonpatana, Pitiya; Mohamed, Hussein M H; Shynkaryk, Mykola; Heskitt, Brian; Yousef, Ahmed E; Sastry, Sudhir K
2013-11-01
To accomplish continuous flow ohmic heating of a low-acid food product, sufficient heat treatment needs to be delivered to the slowest-heating particle at the outlet of the holding section. This research was aimed at developing mathematical models for sterilization of a multicomponent food in a pilot-scale ohmic heater with electric-field-oriented parallel to the flow and validating microbial inactivation by inoculated particle methods. The model involved 2 sets of simulations, one for determination of fluid temperatures, and a second for evaluating the worst-case scenario. A residence time distribution study was conducted using radio frequency identification methodology to determine the residence time of the fastest-moving particle from a sample of at least 300 particles. Thermal verification of the mathematical model showed good agreement between calculated and experimental fluid temperatures (P > 0.05) at heater and holding tube exits, with a maximum error of 0.6 °C. To achieve a specified target lethal effect at the cold spot of the slowest-heating particle, the length of holding tube required was predicted to be 22 m for a 139.6 °C process temperature with volumetric flow rate of 1.0 × 10(-4) m3/s and 0.05 m in diameter. To verify the model, a microbiological validation test was conducted using at least 299 chicken-alginate particles inoculated with Clostridium sporogenes spores per run. The inoculated pack study indicated the absence of viable microorganisms at the target treatment and its presence for a subtarget treatment, thereby verifying model predictions.
Singh, Ashok
2015-01-01
The present book provides guidance to understanding complicated coupled processes based on the experimental data available and implementation of developed algorithms in numerical codes. Results of selected test cases in the fields of closed-form solutions (e.g., deformation processes), single...... processes (such as groundwater flow) as well as coupled processes are presented. It is part of the OpenGeoSys initiative - an open source project to share knowledge and experience in environmental analysis and scientific computation with the community....
Zheng, L.; Samper, J.; Montenegro, L.; Major, J.C.
2008-10-15
During the construction and operational phases of a high-level radioactive waste (HLW) repository constructed in a clay formation, ventilation of underground drifts will cause desaturation and oxidation of the rock. The Ventilation Experiment (VE) was performed in a 1.3 m diameter unlined horizontal microtunnel on Opalinus clay at Mont Terri underground research laboratory in Switzerland to evaluate the impact of desaturation on rock properties. A multiphase flow and reactive transport model of VE is presented here. The model accounts for liquid, vapor and air flow, evaporation/condensation and multicomponent reactive solute transport with kinetic dissolution of pyrite and siderite and local-equilibrium dissolution/precipitation of calcite, ferrihydrite, dolomite, gypsum and quartz. Model results reproduce measured vapor flow, liquid pressure and hydrochemical data and capture the trends of measured relative humidities, although such data are slightly overestimated near the rock interface due to uncertainties in the turbulence factor. Rock desaturation allows oxygen to diffuse into the rock and triggers pyrite oxidation, dissolution of calcite and siderite, precipitation of ferrihydrite, dolomite and gypsum and cation exchange. pH in the unsaturated rock varies from 7.8 to 8 and is buffered by calcite. Computed changes in the porosity and the permeability of Opalinus clay in the unsaturated zone caused by oxidation and mineral dissolution/precipitation are smaller than 5%. Therefore, rock properties are not expected to be affected significantly by ventilation of underground drifts during construction and operational phases of a HLW repository in clay.
FLUID FLOW IN ROTATING HELICAL SQUARE DUCTS
Chen Hua-jun; Zhang Ben-zhao; Zhang Jin-suo
2003-01-01
A numerical study is made for a fully developed laminar flow in rotating helical pipes.Due to the rotation, the Coriolis force can also contribute to the secondary flow.The interaction between rotation, torsion, and curvature complicates the flow characteristics.The effects of rotation and torsion on the flow transitions are studied in details.The results show that there are obvious differences between the flow in rotating ducts and in helical ducts without rotation.Certain hitherto unknown flow patterns are found.The effects of rotation and torsion on the friction factor are also examined.Present results show the characteristics of the fluid flow in rotating helical square ducts.
Katyal, A.K.; Kaluarachchi, J.J.; Parker, J.C.
1991-05-01
The manual describes a two-dimensional finite element model for coupled multiphase flow and multicomponent transport in planar or radially symmetric vertical sections. Flow and transport of three fluid phases, including water, nonaqueous phase liquid (NAPL), and gas are considered by the program. The program can simulate flow only or coupled flow and transport. The flow module can be used to analyze two phases, water and NAPL, with the gas phase held at constant pressure, or explicit three-phase flow of water, NAPL, and gas at various pressures. The transport module can handle up to five components which partition among water, NAPL, gas and solid phases assuming either local equilibrium or first-order mass transfer. Three phase permeability-saturation-capillary pressure relations are defined by an extension of the van Genuchten model. The governing equations are solved using an efficient upstream-weighted finite element scheme. The report describes the required inputs for flow analysis and transport analysis. Time dependent boundary conditions for flow and transport analysis can be handled by the program and are described in the report. Detailed instructions for creating data files needed to run the program and example input and output files are given in appendices.
Yuen, Po Ki
2013-05-07
This article presents a simple method for controlling fluid in microfluidic devices without the need for valves or pumps. A fluid conveyance extension is fluidly coupled to the enclosed outlet chamber of a microfluidic device. After a fluid is introduced into the microfluidic device and saturates the fluid conveyance extension, a fluid flow in the microfluidic device is generated by contacting an absorbent microfluidic flow modulator with the fluid conveyance extension to absorb the fluid from the fluid conveyance extension through capillary action. Since the fluid in the microfluidic device is fluidly coupled with the fluid conveyance extension and the fluid conveyance extension is fluidly coupled with the absorbent microfluidic flow modulator, the absorption rate of the absorbent microfluidic flow modulator, which is the rate at which the absorbent microfluidic flow modulator absorbs fluid, matches the fluid flow rate in the microfluidic device. Thus, the fluid flow rate in the microfluidic device is set by the absorption rate of the absorbent microfluidic flow modulator. Sheath flow and fluid switching applications are demonstrated using this simple fluid control method without the need for valves or pumps. Also, the ability to control the fluid flow rate in the microfluidic device is demonstrated using absorbent microfluidic flow modulators with various absorbent characteristics and dimensions.
Topological fluid dynamics of interfacial flows
Brøns, Morten
1994-01-01
The topological description of flows in the vicinity of a solid boundary, that is familiar from the aerodynamics literature, has recently been extended to the case of flow at a liquid–gas interface or a free surface by Lugt [Phys. Fluids 30, 3647 (1987)]. Lugt's work is revisited in a more general...... setting, including nonconstant curvature of the interface and gradients of surface tension, using tools of modern nonlinear dynamics. Bifurcations of the flow pattern occur at degenerate configurations. Using the theory of unfolding, this paper gives a complete description of the bifurcations that depend...... on terms up to the second order. The general theory of this paper is applied to the topology of streamlines during the breaking of a wave and to the flow below a stagnant surface film. Physics of Fluids is copyrighted by The American Institute of Physics....
Henríquez Rivera, Rafael G.; Zhang, Xiao; Graham, Michael D.
2016-10-01
A mechanistic model, derived from kinetic theory, is developed to describe segregation in confined multicomponent suspensions such as blood. It incorporates the two key phenomena arising in these systems at low Reynolds number: hydrodynamic pair collisions and hydrodynamic migration. Two flow profiles are considered: simple shear flow (plane Couette flow) and plane Poiseuille flow. The theory begins by writing the evolution of the number density of each component in the suspension as a master equation with contributions from migration and collisions. By making judicious approximations for the collisions, this system of integrodifferential equations is reduced to a set of drift-diffusion equations. We focus attention on the case of a binary suspension with a deformable primary component that completely dominates the collision dynamics in the system and a trace component that has no effect on the primary. The model captures the phenomena of depletion layer formation and margination observed in confined multicomponent suspensions of deformable particles. The depletion layer thickness of the primary component is predicted to follow a master curve relating it in a specific way to confinement ratio and volume fraction. Results from various sources (experiments, detailed simulations, master equation solutions) with different parameters (flexibility of different components in the suspension, viscosity ratio, confinement, among others) collapse onto the same curve. For sufficiently dilute suspensions the analytical form predicted by the drift-diffusion theory for this curve is in excellent agreement with results from these other sources with only one adjustable parameter. In a binary suspension, several regimes of segregation arise, depending on the value of a "margination parameter" M . Most importantly, in both Couette and Poiseuille flows there is a critical value of M below which a sharp "drainage transition" occurs: one component is completely depleted from the bulk
Fluid Flows driven by Oscillating Body Force
Vladimirov, V A
2016-01-01
In this note we consider general formulation of Euler's equations for an inviscid incompressible homogeneous fluid with an oscillating body force. Our aim is to derive the averaged equations for these flows with the help of two-timing method. Our main result is the general and simple form of the equation describing the averaged flows, which are derived without making any additional assumptions. The presented results can have many interesting applications.
Corner Flow of Power Law Fluids
Henriksen, P.; Hassager, Ole
1989-01-01
A local analysis of the flow of power law fluids near corners is performed. The equation for the stream function is shown to allow separated solutions in plane polar coordinates. The radial behavior is shown to be algebraic and results are given for the exponent for different values of corner ang...
Topological fluid mechanics of Axisymmetric Flow
Brøns, Morten
1998-01-01
to the authors knowledge has not been used systematically to high orders in topological fluid mechanics. We compare the general results with experimental and computational results on the Vogel-Ronneberg flow. We show that the topology changes observed when recirculating bubbles on the vortex axis are created...
Hodograph method in MHD orthogonal fluid flows
P. V. Nguyen
1992-01-01
Full Text Available Equations for steady plane MHD orthogonal flows of a viscous incompressible fluid of finite electrical conductivity are recast in the hodograph plane by using the Legendre transform function of the streamfunction. Three examples are studied to illustrate the developed theory. Solutions and geometries for these examples are determined.
Fluid flow for chemical and process engineers
Holland, F
1995-01-01
This major new edition of a popular undergraduate text covers topics of interest to chemical engineers taking courses on fluid flow. These topics include non-Newtonian flow, gas-liquid two-phase flow, pumping and mixing. It expands on the explanations of principles given in the first edition and is more self-contained. Two strong features of the first edition were the extensive derivation of equations and worked examples to illustrate calculation procedures. These have been retained. A new extended introductory chapter has been provided to give the student a thorough basis to understand the methods covered in subsequent chapters.
Oscillatory Couette flow of rotating Sisko fluid
T.HAYAT; S.ABELMAN; M.HAMESE
2014-01-01
The oscillatory Couette flow of a magnetohydrodynamic (MHD) Sisko fluid between two infinite non-conducting parallel plates is explored in a rotating frame. The lower plate is fixed, and the upper plate is oscillating in its own plane. Using MATLAB, a numerical solution to the resulting nonlinear system is presented. The influence of the physical parameters on the velocity components is analyzed. It is found that the effect of rotation on the primary velocity is more significant than that on the secondary velocity. Further, the oscillatory character in the flow is also induced by rotation. The considered flow situation behaves inertialess when the Reynolds number is small.
Cerebrospinal fluid flow. Pt. 3; Pathological cerebrospinal fluid pulsations
Schroth, G. (Dept. of Neuradiology, Tuebingen Univ. (Germany)); Klose, U. (Dept. of Neuradiology, Tuebingen Univ. (Germany))
1992-12-01
Cardiac- and respiration-related movements of the cerebrospinal fluid (CSF) were investigated by MRI in 71 patients. In most patients with arteriosclerotic occlusive vascular disease CSF pulsations are normal. Decreased pulsatile flow is detectable in those with arteriovenous malformations, intracranial air and following lumbar puncture and withdrawal of CSF. Increased pulsatile flow in the cerebral aqueduct was found in 2 patients with large aneurysms, idiopathic communicating syringomyelia and in most cases of normal pressure hydrocephalus (NPH). CSF flow in the cervical spinal canal is, however, reduced or normal in NPH, indicating reduction of the unfolding ability of the surface of the brain and/or inhibition of rapid CSF movements in the subrachnoid space over its convexity. (orig.)
LAMINAR FLUID FLOW IN HELICAL ELLIPTICAL PIPE
无
2000-01-01
In this paper, using an orthogonal curvilinear coordinate system and solving the complete N-S equations, we analyzed the flow in a helical elliptical duct by the perturbation method. The first-order solutions of the stream function Ψ, axial velocity w and the velocity of secondary flow (u, v) were obtained. The effects of torsion, curvature and the axial pressure gradient on the secondary flow were discussed in detail. The study indicates that the torsion has first-order effect on the secondary flow in a helical elliptical pipe, the secondary flow is dominated by torsion when the axial pressure gradient is small and for increasing gradient the secondary flow is eventually dominated by the effect due to curvature. The fact that the torsion has no effect on fluid flow in a helical pipe with a circular cross section was also confirmed. The most important conclusion is that the flow in a helical elliptical pipe to the first-order can be obtained as a combination of the flow in a toroidal pipe and the flow in a twisted pipe.
Modeling Tools Predict Flow in Fluid Dynamics
2010-01-01
"Because rocket engines operate under extreme temperature and pressure, they present a unique challenge to designers who must test and simulate the technology. To this end, CRAFT Tech Inc., of Pipersville, Pennsylvania, won Small Business Innovation Research (SBIR) contracts from Marshall Space Flight Center to develop software to simulate cryogenic fluid flows and related phenomena. CRAFT Tech enhanced its CRUNCH CFD (computational fluid dynamics) software to simulate phenomena in various liquid propulsion components and systems. Today, both government and industry clients in the aerospace, utilities, and petrochemical industries use the software for analyzing existing systems as well as designing new ones."
An implicit numerical model for multicomponent compressible two-phase flow in porous media
Zidane, Ali; Firoozabadi, Abbas
2015-11-01
We introduce a new implicit approach to model multicomponent compressible two-phase flow in porous media with species transfer between the phases. In the implicit discretization of the species transport equation in our formulation we calculate for the first time the derivative of the molar concentration of component i in phase α (cα, i) with respect to the total molar concentration (ci) under the conditions of a constant volume V and temperature T. The species transport equation is discretized by the finite volume (FV) method. The fluxes are calculated based on powerful features of the mixed finite element (MFE) method which provides the pressure at grid-cell interfaces in addition to the pressure at the grid-cell center. The efficiency of the proposed model is demonstrated by comparing our results with three existing implicit compositional models. Our algorithm has low numerical dispersion despite the fact it is based on first-order space discretization. The proposed algorithm is very robust.
Full-Eulerian fluid-structure coupling simulation of hyperelastic channel flow
Nagano, Naohiro; Sugiyama, Kazuyasu; Takeuchi, Shintaro; Satoshi, II; Takagi, Shu; Matsumoto, Yoichiro
2010-11-01
A full-Eulerian simulation for coupling a Newtonian fluid and hyperelastic material is conducted. The system involves an interaction problem between the fluid and hyperelastic walls and is driven by pressure difference, mimicking a blood flow in a blood vessel. A single set of the governing equations for the fluid and solid is employed, and a volume-of-fluid idea is employed to describe a multi-component geometry. The solid stress is defined in Eulerian frame by using a left Cauchy-Green deformation tensor, and the temporal change in the solid deformation is described by updating the tensor. The method employs a uniform fixed grid system for both fluid and solid and it does not require any mesh generation or reconstruction, aiming at facilitating the practical bio-mechanical fluid-structure analysis based on a medical image. The validity of the simulation results is established through comparison with a theoretical prediction. As an application of the present method, pulsating flows are simulated to demonstrate a nonlinear behavior of the flow rate on the pulsating amplitude, and an effect of employing an anisotropic hyperelastic material is discussed.
Amooie, Mohammad Amin; Soltanian, Mohammad Reza; Moortgat, Joachim
2016-11-01
Fluid mixing and its interplay with viscous fingering as well as flow channeling through heterogeneous media have been traditionally studied for fully (im)miscible conditions in which a (two-) single-phase system is represented by two components, e.g. a solvent and a solute, with (zero) infinite mutual solubility. However, many subsurface problems, e.g. gas injection/migration in hydrocarbon reservoirs, involve multiple species transfer. Multicomponent fluid properties behave non-linearly, through an equation of state, as a function of temperature, pressure, and compositions. Depending on the minimum miscibility pressure, a two-phase region with finite, non-zero mutual solubility may develop, e.g. in a partially-miscible system. Here we study mixing of fluids with partial mutual solubility, induced by viscous flow fingering, channeling, and species transport within and between phases. We uncover non-linear mixing dynamics of a finite-size slug of a less viscous fluid attenuated by a carrier fluid during rectilinear displacement. We perform accurate numerical simulations that are thermodynamically-consistent to capture fingering patterns and complex phase behavior of mixtures. The results provide a broad perspective into how multiphase flow can alter fluid mixing in porous media.
Visualization of working fluid flow in gravity assisted heat pipe
Nemec Patrik
2015-01-01
Full Text Available Heat pipe is device working with phase changes of working fluid inside hermetically closed pipe at specific pressure. The phase changes of working fluid from fluid to vapor and vice versa help heat pipe to transport high heat flux. The article deal about construction and processes casing in heat pipe during operation. Experiment visualization of working fluid flow is performed with glass heat pipe filed with ethanol. The visualization of working fluid flow explains the phenomena as working fluid boiling, nucleation of bubbles, vapor flow, vapor condensation on the wall, vapor and condensate flow interaction, flow down condensate film thickness on the wall, occurred during the heat pipe operation.
Visualization of working fluid flow in gravity assisted heat pipe
Nemec, Patrik; Malcho, Milan
2015-05-01
Heat pipe is device working with phase changes of working fluid inside hermetically closed pipe at specific pressure. The phase changes of working fluid from fluid to vapor and vice versa help heat pipe to transport high heat flux. The article deal about construction and processes casing in heat pipe during operation. Experiment visualization of working fluid flow is performed with glass heat pipe filed with ethanol. The visualization of working fluid flow explains the phenomena as working fluid boiling, nucleation of bubbles, vapor flow, vapor condensation on the wall, vapor and condensate flow interaction, flow down condensate film thickness on the wall, occurred during the heat pipe operation.
Fully non-linear cosmological perturbations of multicomponent fluid and field systems
Hwang, Jai-chan; Noh, Hyerim; Park, Chan-Gyung
2016-09-01
We present fully non-linear and exact cosmological perturbation equations in the presence of multiple components of fluids and minimally coupled scalar fields. We ignore the tensor-type perturbation. The equations are presented without taking the temporal gauge condition in the Friedmann background with general curvature and the cosmological constant. We include the anisotropic stress. Even in the absence of anisotropic stress of individual component, the multiple component nature introduces the anisotropic stress in the collective fluid quantities. We prove the Newtonian limit of multiple fluids in the zero-shear gauge and the uniform-expansion gauge conditions, present the Newtonian hydrodynamic equations in the presence of general relativistic pressure in the zero-shear gauge, and present the fully non-linear equations and the third-order perturbation equations of the non-relativistic pressure fluids in the CDM-comoving gauge.
Piezoelectric Energy Harvesting in Internal Fluid Flow
Hyeong Jae Lee
2015-10-01
Full Text Available We consider piezoelectric flow energy harvesting in an internal flow environment with the ultimate goal powering systems such as sensors in deep oil well applications. Fluid motion is coupled to structural vibration via a cantilever beam placed in a converging-diverging flow channel. Two designs were considered for the electromechanical coupling: first; the cantilever itself is a piezoelectric bimorph; second; the cantilever is mounted on a pair of flextensional actuators. We experimentally investigated varying the geometry of the flow passage and the flow rate. Experimental results revealed that the power generated from both designs was similar; producing as much as 20 mW at a flow rate of 20 L/min. The bimorph designs were prone to failure at the extremes of flow rates tested. Finite element analysis (FEA showed fatigue failure was imminent due to stress concentrations near the bimorph’s clamped region; and that robustness could be improved with a stepped-joint mounting design. A similar FEA model showed the flextensional-based harvester had a resonant frequency of around 375 Hz and an electromechanical coupling of 0.23 between the cantilever and flextensional actuators in a vacuum. These values; along with the power levels demonstrated; are significant steps toward building a system design that can eventually deliver power in the Watts range to devices down within a well.
Thermodynamics of Fluids Under Flow Second Edition
Jou, David; Criado-Sancho, Manuel
2011-01-01
This is the second edition of the book “Thermodynamics of Fluids under Flow,” which was published in 2000 and has now been corrected, expanded and updated. This is a companion book to our other title Extended irreversible thermodynamics (D. Jou, J. Casas-Vázquez and G. Lebon, Springer, 4th edition 2010), and of the textbook Understanding non-equilibrium thermodynamics (G. Lebon, D. Jou and J. Casas-Vázquez, Springer, 2008. The present book is more specialized than its counterpart, as it focuses its attention on the non-equilibrium thermodynamics of flowing fluids, incorporating non-trivial thermodynamic contributions of the flow, going beyond local equilibrium theories, i.e., including the effects of internal variables and of external forcing due to the flow. Whereas the book's first edition was much more focused on polymer solutions, with brief glimpses into ideal and real gases, the present edition covers a much wider variety of systems, such as: diluted and concentrated polymer solutions, polymer ble...
Fluids in crustal deformation: Fluid flow, fluid-rock interactions, rheology, melting and resources
Lacombe, Olivier; Rolland, Yann
2016-11-01
Fluids exert a first-order control on the structural, petrological and rheological evolution of the continental crust. Fluids interact with rocks from the earliest stages of sedimentation and diagenesis in basins until these rocks are deformed and/or buried and metamorphosed in orogens, then possibly exhumed. Fluid-rock interactions lead to the evolution of rock physical properties and rock strength. Fractures and faults are preferred pathways for fluids, and in turn physical and chemical interactions between fluid flow and tectonic structures, such as fault zones, strongly influence the mechanical behaviour of the crust at different space and time scales. Fluid (over)pressure is associated with a variety of geological phenomena, such as seismic cycle in various P-T conditions, hydrofracturing (including formation of sub-horizontal, bedding-parallel veins), fault (re)activation or gravitational sliding of rocks, among others. Fluid (over)pressure is a governing factor for the evolution of permeability and porosity of rocks and controls the generation, maturation and migration of economic fluids like hydrocarbons or ore forming hydrothermal fluids, and is therefore a key parameter in reservoir studies and basin modeling. Fluids may also help the crust partially melt, and in turn the resulting melt may dramatically change the rheology of the crust.
Special-relativistic model flows of viscous fluid
Rogava, A D
1996-01-01
Two, the most simple cases of special-relativistic flows of a viscous, incompressible fluid are considered: plane Couette flow and plane Poiseuille flow. Considering only the regular motion of the fluid we found the distribution of velocity in the fluid (velocity profiles) and the friction force, acting on immovable wall. The results are expressed through simple analytical functions for the Couette flow, while for the Poiseiulle flow they are expressed by higher transcendental functions (Jacobi's elliptic functions).
Quantitative evaluation fo cerebrospinal fluid shunt flow
Chervu, S.; Chervu, L.R.; Vallabhajosyula, B.; Milstein, D.M.; Shapiro, K.M.; Shulman, K.; Blaufox, M.D.
1984-01-01
The authors describe a rigorous method for measuring the flow of cerebrospinal fluid (CSF) in shunt circuits implanted for the relief of obstructive hydrocephalus. Clearance of radioactivity for several calibrated flow rates was determined with a Harvard infusion pump by injecting the Rickham reservoir of a Rickham-Holter valve system with 100 ..mu..Ci of Tc-99m as pertechnetate. The elliptical and the cylindrical Holter valves used as adjunct valves with the Rickham reservoir yielded two different regression lines when the clearances were plotted against flow rats. The experimental regression lines were used to determine the in vivo flow rates from clearances calculated after injecting the Rickham reservoirs of the patients. The unique clearance characteristics of the individual shunt systems available requires that calibration curves be derived for an entire system identical to one implanted in the patient being evaluated, rather than just the injected chamber. Excellent correlation between flow rates and the clinical findings supports the reliability of this method of quantification of CSF shunt flow, and the results are fully accepted by neurosurgeons.
Flow acoustics in solid-fluid structures
Willatzen, Morten; Mads, Mikhail Vladimirovich Deryabin
2008-01-01
along the x direction. In the first part of the paper, the governing set of differential equations are derived as well as the imposed boundary conditions. Solutions are provided using Hamilton's equations for the wavenumber vs. frequency as a function of the number and thickness of solid layers....... A wavenumber condition for an arbitrary set of consecutive solid and fluid layers, involving four propagating waves in each solid region, is obtained again using the monodromy matrix method. Case examples are finally discussed.......The governing two-dimensional equations of a heterogeneous material composed of a fluid (allowed to flow in the absence of acoustic excitations) and a crystalline piezoelectric cubic solid stacked one-dimensionally (along the z direction) are derived and special emphasis is given to the discussion...
Flow of viscoplastic fluids in a rotating concentric annulus
Hassager, Ole; Bittleston, Simon H.
1992-01-01
A difficulty in any flow calculation with viscoplastic fluids such as Bingham fluids is the determination of possible plug zones in which no deformation occurs. This paper investigates the flow in a concentric annulus when there is both an axial and tangential flow, the tangent flow arising from ...
Visualization of working fluid flow in gravity assisted heat pipe
Nemec Patrik; Malcho Milan
2015-01-01
Heat pipe is device working with phase changes of working fluid inside hermetically closed pipe at specific pressure. The phase changes of working fluid from fluid to vapor and vice versa help heat pipe to transport high heat flux. The article deal about construction and processes casing in heat pipe during operation. Experiment visualization of working fluid flow is performed with glass heat pipe filed with ethanol. The visualization of working fluid flow explains the phenomena as working fl...
Modeling Fluid Flow in Faulted Basins
Faille I.
2014-07-01
Full Text Available This paper presents a basin simulator designed to better take faults into account, either as conduits or as barriers to fluid flow. It computes hydrocarbon generation, fluid flow and heat transfer on the 4D (space and time geometry obtained by 3D volume restoration. Contrary to classical basin simulators, this calculator does not require a structured mesh based on vertical pillars nor a multi-block structure associated to the fault network. The mesh follows the sediments during the evolution of the basin. It deforms continuously with respect to time to account for sedimentation, erosion, compaction and kinematic displacements. The simulation domain is structured in layers, in order to handle properly the corresponding heterogeneities and to follow the sedimentation processes (thickening of the layers. In each layer, the mesh is unstructured: it may include several types of cells such as tetrahedra, hexahedra, pyramid, prism, etc. However, a mesh composed mainly of hexahedra is preferred as they are well suited to the layered structure of the basin. Faults are handled as internal boundaries across which the mesh is non-matching. Different models are proposed for fault behavior such as impervious fault, flow across fault or conductive fault. The calculator is based on a cell centered Finite Volume discretisation, which ensures conservation of physical quantities (mass of fluid, heat at a discrete level and which accounts properly for heterogeneities. The numerical scheme handles the non matching meshes and guaranties appropriate connection of cells across faults. Results on a synthetic basin demonstrate the capabilities of this new simulator.
Fluid flow dynamics in MAS systems.
Wilhelm, Dirk; Purea, Armin; Engelke, Frank
2015-08-01
The turbine system and the radial bearing of a high performance magic angle spinning (MAS) probe with 1.3mm-rotor diameter has been analyzed for spinning rates up to 67kHz. We focused mainly on the fluid flow properties of the MAS system. Therefore, computational fluid dynamics (CFD) simulations and fluid measurements of the turbine and the radial bearings have been performed. CFD simulation and measurement results of the 1.3mm-MAS rotor system show relatively low efficiency (about 25%) compared to standard turbo machines outside the realm of MAS. However, in particular, MAS turbines are mainly optimized for speed and stability instead of efficiency. We have compared MAS systems for rotor diameter of 1.3-7mm converted to dimensionless values with classical turbomachinery systems showing that the operation parameters (rotor diameter, inlet mass flow, spinning rate) are in the favorable range. This dimensionless analysis also supports radial turbines for low speed MAS probes and diagonal turbines for high speed MAS probes. Consequently, a change from Pelton type MAS turbines to diagonal turbines might be worth considering for high speed applications. CFD simulations of the radial bearings have been compared with basic theoretical values proposing considerably smaller frictional loss values. The discrepancies might be due to the simple linear flow profile employed for the theoretical model. Frictional losses generated inside the radial bearings result in undesired heat-up of the rotor. The rotor surface temperature distribution computed by CFD simulations show a large temperature gradient over the rotor.
Flow Diode and Method for Controlling Fluid Flow Origin of the Invention
Dyson, Rodger W (Inventor)
2015-01-01
A flow diode configured to permit fluid flow in a first direction while preventing fluid flow in a second direction opposite the first direction is disclosed. The flow diode prevents fluid flow without use of mechanical closures or moving parts. The flow diode utilizes a bypass flowline whereby all fluid flow in the second direction moves into the bypass flowline having a plurality of tortuous portions providing high fluidic resistance. The portions decrease in diameter such that debris in the fluid is trapped. As fluid only travels in one direction through the portions, the debris remains trapped in the portions.
Statistic fluid dynamic of multiphase flow
Lim, Hyunkyung; Glimm, James; Zhou, Yijie; Jiao, Xiangmin
2012-11-01
We study a turbulent two-phase fluid mixing problem from a statistical point of view. The test problem is high speed turbulent two-phase Taylor-Couette flow. We find extensive mixing in a transient state between an initial unstable and a final stable configuration. With chemical processing as a motivation, we estimate statistically surface area, droplet size distribution and transient droplet duration. This work is supported in part by the Nuclear Energy University Program of the Department of Energy, Battelle Energy Alliance LLC 00088495.
Helical flows of fractionalized Burgers' fluids
Muhammad Jamil
2012-03-01
Full Text Available The unsteady flows of Burgers’ fluid with fractional derivatives model, through a circular cylinder, is studied by means of the Laplace and finite Hankel transforms. The motion is produced by the cylinder that at the initial moment begins to rotate around its axis with an angular velocity Ωt, and to slide along the same axis with linear velocity Ut. The solutions that have been obtained, presented in series form in terms of the generalized Ga,b,c(•, t functions, satisfy all imposed initial and boundary conditions. Moreover, the corresponding solutions for fractionalized Oldroyd-B, Maxwell and second grade fluids appear as special cases of the present results. Furthermore, the solutions for ordinary Burgers’, Oldroyd-B, Maxwell, second grade and Newtonian performing the same motion, are also obtained as special cases of general solutions by substituting fractional parameters α = β = 1. Finally, the influence of the pertinent parameters on the fluid motion, as well as a comparison among models, is shown by graphical illustrations.
Optical density measurements in a multiphase cryogenic fluid flow system
Korman, Valentin; Wiley, John; Gregory, Don A.
2006-05-01
An accurate determination of fluid flow in a cryogenic propulsion environment is difficult under the best of circumstances. The extreme thermal environment increases the mechanical constraints, and variable density conditions create havoc with traditional flow measurement schemes. Presented here are secondary results of cryogenic testing of an all-optical sensor capable of a mass flow measurement by directly interrogating the fluid's density state and a determination of the fluid's velocity. The sensor's measurement basis does not rely on any inherent assumptions as to the state of the fluid flow (density or otherwise). The fluid sensing interaction model will be discussed. Current test and evaluation data and future development work will be presented.
14 CFR 23.1095 - Carburetor deicing fluid flow rate.
2010-01-01
... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Carburetor deicing fluid flow rate. 23.1095 Section 23.1095 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... Induction System § 23.1095 Carburetor deicing fluid flow rate. (a) If a carburetor deicing fluid system...
Numerical simulation of two-component flow fluid - fluid in the microchannel T- type
Shebeleva A.A.
2015-01-01
Full Text Available Results of testing methodology for calculating two-phase flows based on the method of fluid in the cells (VOF method, and the procedure for CSF accounting of surface tension forces in the microchannel are considered in the work. Mathematical modeling of two-component flow fluid -fluid in the T- microchannel conducted using this methodology. The following flow regimes studied slug flow, rivulet flow, parallel flow, dispersed (droplet flow, plug flow. Comparison of numerical results with experimental data done. Satisfactory agreement between the calculated values with the experimental data obtained.
Reactive fluid flow models and applications to diagenesis, mineral deposits and crustal rocks
Lasaga, A.C.; Rye, D.M.
1993-08-01
Funds are requested for a combined theoretical and field study of coupled fluid flow, heat and mass transport, and chemical reaction in hydrothermal and metamorphic systems. An existing computer code developed by the applicants which numerically treats multi-component, finite-rate reactions combined with advective and dispersive transport in one and two dimensions and which incorporates isotopic exchange and heat and mass transfer will continue to be developed and applied in a variety of geological settings. The code we have developed simultaneously solves for mass transport and reaction, thus offering a significant improvement in computational efficiency over existing ``batch`` reaction path codes. By coupling flow and chemical reaction in a hydrothermal system, we can explicitly investigate the extent to which characteristic flow-reaction paths govern the chemical evolution of the fluids in a hydrothermal system. The concept of a flow-reaction path is particularly important where certain portions of mature hydrothermal systems may exhaust the buffer capacity of the rock as the primary mineralogy is consumed. In these instances 7 fluids traversing distinct regions within the hydrothermal system may experience very different reaction histories, even where the system can be described as nearly isothermal. The study of paleo-hydrothermal systems can yield some important insights into the chemical dynamics of hydrothermal systems in general. As an example of a paleo-hydrothermal system, we have considered the geochemical evolution of ``porphyry-copper`` type mineralization.
On spherically symmetric solutions with horizon in model with multicomponent anisotropic fluid
Dehnen, H
2003-01-01
A family of spherically symmetric solutions in the model with m-component anisotropic fluid is considered. The metric of the solution depends on parameters q_s, s = 1,...,m, relating radial pressures and the densities and contains (n -1)m parameters corresponding to Ricci-flat "internal space" metrics and obeying certain m(m-1)/2 ("orthogonality") relations. For q_s = 1 (for all s) and certian equations of state (p_i^s = \\pm \\rho^s) the metric coincides with the metric of intersecting black brane solution in the model with antisymmetric forms. A family of solutions with (regular) horizon corresponding to natural numbers q_s = 1,2,... is singled out. Certain examples of "generalized simulation" of intersecting M-branes in D=11 supergravity are considered. The post-Newtonian parameters \\beta and \\gamma corresponding to the 4-dimensional section of the metric are calculated.
Performance analysis a of solar driven organic Rankine cycle using multi-component working fluids
Baldasso, E.; Andreasen, J. G.; Modi, A.
2015-01-01
Among the different renewable sources of energy, solar power could play a primary role in the development of a more sustainable electricity generation system. While large scale concentrated solar power plants based on the steam Rankine cycle have already been proved to be cost effective, research...... cycle. The purpose of this paper is to optimize a low temperature organic Rankine cycle tailored for solar applications. The objective of the optimization is the maximization of the solar to electrical efficiency and the optimization parameters are the working fluid and the turbine inlet temperature...... is still under progress for small scale low temperature solar-driven power plants. The steam Rankine cycle is suitable for high temperature applications, but its efficiency drastically decreases as the heat source temperature drops. In these cases a much more promising configuration is the organic Rankine...
Heat transfer and fluid flow in microchannels
Mala, Ghulam Mohiuddin
Fluid flow and heat transfer characteristics in microchannels of different cross-sections; parallel plate, cylindrical and trapezoidal microchannels were studied. The trapezoidal microchannels were etched in silicon and glass by photolithographic techniques. The cylindrical microchannels of fused silica and stainless steel were readily available. Channels with depths of 18 μm to 300 μm were studied. The study was divided into three parts viz. theoretical modeling, numerical simulation and experimentation. Electrokinetic effects such as the effects of electrical double layer (EDL) at the solid-liquid interface and surface roughness effects were considered. An experimental apparatus was constructed and a procedure devised to measure the flow rate, pressure drop, temperatures and electrokinetic parameters like streaming potential, streaming current, and conductivity of the working fluid. Great care was taken so that the measurements were accurate and repeatable. For steady state laminar flow and heat transfer in microchannels, mathematical models were developed that consider the effects of electrical double layer and surface roughness at the microchannel walls. The non- linear, 2-D, Poisson-Boltzmann equation that describes the potential distribution at the solid liquid interface was solved numerically and results were compared with a linear approximate solution that overestimates the potential distribution for higher values of zeta potential. Effects of the EDL field at the solid-liquid interface, surface roughness at the microchannel walls and the channel size, on the velocity distribution, streaming potential, apparent viscosity, temperature distribution and heat transfer characteristics are discussed. The experimental results indicate significant departure in flow characteristics from the predictions of the Navier-Stokes equations, referred to as conventional theory. The difference between the experimental results and theoretical predictions decreases as the
Multiple-component lattice Boltzmann equation for fluid-filled vesicles in flow.
Halliday, I; Lishchuk, S V; Spencer, T J; Pontrelli, G; Care, C M
2013-02-01
We document the derivation and implementation of extensions to a two-dimensional, multicomponent lattice Boltzmann equation model, with Laplace law interfacial tension. The extended model behaves in such a way that the boundary between its immiscible drop and embedding fluid components can be shown to describe a vesicle of constant volume bounded by a membrane with conserved length, specified interface compressibility, bending rigidity, preferred curvature, and interfacial tension. We describe how to apply this result to several, independent vesicles. The extended scheme is completely Eulerian, and it represents a two-way coupled vesicle membrane and flow within a single framework. Unlike previous methods, our approach dispenses entirely with the need explicitly to track the membrane, or boundary, and makes no use whatsoever of computationally expensive and intricate interface tracking and remeshing. Validation data are presented, which demonstrate the utility of the method in the simulation of the flow of high volume fraction suspensions of deformable objects.
Developments in the flow of complex fluids in tubes
Siginer, Dennis A
2015-01-01
This book is dedicated to the tube flow of viscoelastic fluids and Newtonian single and multi-phase particle-laden fluids. This succinct volume collects the most recent analytical developments and experimental findings, in particular in predicting the secondary field, highlighting the historical developments which led to the progress made. This book brings a fresh and unique perspective and covers and interprets efforts to model laminar flow of viscoelastic fluids in tubes and laminar and turbulent flow of single and multi-phase particle-laden flow of linear fluids in light of the latest findings. This book also: Presents a thorough account of successes and failures in modeling and predicting tube flow of viscoelastic fluids and concentrated particle-laden flow of Newtonian fluids with specific explanations throughout Emphasizes the most up-to-date challenges in the field without requiring the reader to wade through detailed treatment of various theories Bridges the latest research results and established kno...
Linear stability of plane creeping Couette flow for Burgers fluid
Hu, Kai-Xin; Peng, Jie; Zhu, Ke-Qin
2013-02-01
It is well known that plane creeping Couette flow of UCM and Oldroy-B fluids are linearly stable. However, for Burges fluid, which includes UCM and Oldroyd-B fluids as special cases, unstable modes are detected in the present work. The wave speed, critical parameters and perturbation mode are studied for neutral waves. Energy analysis shows that the sustaining of perturbation energy in Poiseuille flow and Couette flow is completely different. At low Reynolds number limit, analytical solutions are obtained for simplified perturbation equations. The essential difference between Burgers fluid and Oldroyd-B fluid is revealed to be the fact that neutral mode exists only in the former.
Perfect fluid flow from granular jet impact
Ellowitz, Jake; Zhang, Wendy W
2012-01-01
Experiments on the impact of a densely-packed jet of non-cohesive grains onto a fixed target show that the impact produces an ejecta sheet comprised of particles in collimated motion. The ejecta sheet leaves the target at a well-defined angle whose value agrees quantitatively with the sheet angle produced by water jet impact. Motivated by these experiments, we examine the idealized problem of dense granular jet impact onto a frictionless target in two dimensions. Numerical results for the velocity and pressure fields within the granular jet agree quantitatively with predictions from an exact solution for 2D perfect-fluid impact. This correspondence demonstrates that the continuum limit controlling the coherent collective motion in dense granular impact is Euler flow.
On stability and turbulence of fluid flows
Heisenberg, Werner
1951-01-01
This investigation is divided into two parts, the treatment of the stability problem of fluid flows on the one hand, and that of the turbulent motion on the other. The first part summarizes all previous investigations under a unified point of view, that is, sets up as generally as possible the conditions under which a profile possesses unstable or stable characteristics, and indicates the methods for solution of the stability equation for any arbitrary velocity profile and for calculation of the critical Reynolds number for unstable profiles. In the second part, under certain greatly idealizing assumptions, differential equations for the turbulent motions are derived and from them qualitative information about several properties of the turbulent velocity distribution is obtained.
Laminar flow of two miscible fluids in a simple network
Karst, Casey M; Geddes, John B
2012-01-01
When a fluid comprised of multiple phases or constituents flows through a network, non-linear phenomena such as multiple stable equilibrium states and spontaneous oscillations can occur. Such behavior has been observed or predicted in a number of networks including the flow of blood through the microcirculation, the flow of picoliter droplets through microfluidic devices, the flow of magma through lava tubes, and two-phase flow in refrigeration systems. While the existence of non-linear phenomena in a network with many inter-connections containing fluids with complex rheology may seem unsurprising, this paper demonstrates that even simple networks containing Newtonian fluids in laminar flow can demonstrate multiple equilibria. The paper describes a theoretical and experimental investigation of the laminar flow of two miscible Newtonian fluids of different density and viscosity through a simple network. The fluids stratify due to gravity and remain as nearly distinct phases with some mixing occurring only by d...
Magnetic resonance imaging of cerebrospinal fluid flow in pediatrics
Heroux, R. [Children' s Hospital of Eastern Ontario, Magnetic Resonance Imaging Dept., Ottawa, Ontario (Canada)
2000-06-30
Magnetic Resonance Imaging of flowing protons in cerebrospinal fluid is useful for demonstrating areas of obstruction or stenosis of the ventricular system causing hydrocephalus. This is used in pediatric patients to assess the circulation of the cerebrospinal fluid. This article discusses two studies. In the first, the cerebrospinal fluid flow study helped the neurosurgeon assess the patency after a third ventriculocisternostomy. The second study evaluated the cerebrospinal fluid flowing through the foramen magnum in a patient with cerebellar tonsilar descent (Chiari malformation) and a syringomyelia. Different techniques to evaluate the flow studies are also discussed. (author)
Some applications of magnetic resonance imaging in fluid mechanics: Complex flows and complex fluids
Bonn, D.; Rodts, S.; Groenink, M.; Rafaï, S.; Shahidzadeh-Bonn, N.; Coussot, P.
2008-01-01
The review deals with applications of magnetic resonance imaging (MRI) techniques to study flow. We first briefly discuss the principles of flow measurement by MRI and give examples of some applications, such as multiphase flows, the MRI rheology of complex fluid flows, and blood flows in the human
Exact solutions for steady flows of second-grade fluids
ZHANG Dao-xiang; FENG Su-xiao; LU Zhi-ming; LIU Yu-lu
2009-01-01
This paper aims to investigate exact solutions for a second-grade fluid flow with the inverse method.By assuming the relation between the vorticity field and the streamfunction,the exact solutions of the motion of plane second-grade fluids are investigated and obtained.The solutions obtained include simple Couette flows,slit jet flows and uniform flows over a series of distributed obstacles.
Two-fluid oscillatory flow in a channel
C.Y.Wang
2011-01-01
The validity of Navier's partial slip condition is investigated by studying the oscillatory flow in a coated channel.The two-fluid model is used to solve the unsteady viscous equations exactly.Partial slip is experienced by the core fluid.It is found that Naviers condition does not hold for an unsteady core fluid.
New nodal methods for fluid flow equations
Michael, Edward-Pierre Edward
Several new highly accurate and highly efficient computational methods, called nodal integral methods (NIMs), for solving steady-state and time-dependent fluid flow equations have been developed. First, a new third order nodal integral method for solving the linear, two-dimensional, steady-state, convection-diffusion equation was developed without introducing Legendre moments of the dependent variable higher than the zeroth moment. Numerical comparisons of the new method with the second order NIM, the upwind difference scheme (UWDS) and the locally exact consistent upwind scheme of second order (LECUSSO) showed that, in the important 1% error range, the new method is more efficient than the UWDS, and the LECUSSO scheme, but, less efficient than the second order NIM. Also two new methods for solving the generic, two-dimensional, time-dependent, convection-diffusion equation were developed. One is a full space-time NIM in which both the spatial and temporal operators are discretized using the nodal integral approach. The other is a hybrid finite-difference/NIM method in which the temporal operator is discretized using a backward finite-difference approximation, and the spatial operator is discretized using the nodal integral approach. It was found, as expected, that the full space-time NIM is second order in both space and time while the hybrid finite-difference/NIM is second order in space but only first order in time. Finally, two new methods for solving the conservation of mass and the Navier-Stokes equations for incompressible fluid flow were developed. One is for the steady-state mass and Navier-Stokes equations while the other solves the time-dependent equations. The spatial stencils that result from these new formulations for the mass and the Navier-Stokes equations are similar to those obtained by traditional staggered-grid finite-difference methods. However, the new methods use second order approximations for both the velocities and the pressures. These
Herschel-Bulkley fluid flow through narrow tubes
Nallapu, Santhosh
2014-01-01
A two-fluid model of Herschel-Bulkley fluid flow through tubes of small diameters is studied. It is assumed that the core region consists of Herschel-Bulkley fluid and Newtonian fluid in the peripheral region. The analytical solutions for velocity, flow flux, effective viscosity, core hematocrit and mean hematocrit have been derived and the effects of various relevant parameters on these flow variables have been studied. It has been observed that the effective viscosity and mean hematocrit increase with yield stress, power-law index, hematocrit and tube radius. Further, the core hematocrit decreases with hematocrit and tube radius.
Some specific features of the NMR study of fluid flows
Davydov, V. V.
2016-07-01
Some specific features of studying fluid flows with a NMR spectrometer are considered. The consideration of these features in the NMR spectrometer design makes it possible to determine the relative concentrations of paramagnetic ions and measure the longitudinal and transverse relaxation times ( T 1 and T 2, respectively) in fluid flows with an error no larger than 0.5%. This approach allows one to completely avoid errors in determining the state of a fluid from measured relaxation constants T 1 and T 2, which is especially urgent when working with medical suspensions and biological solutions. The results of an experimental study of fluid flows are presented.
The friction control of magnetic fluid in the Couette flow
Labkovich, O. N.; Reks, A. G.; Chernobai, V. A.
2017-06-01
In the work characteristic areas of magnetic fluid flow are experimentally determined in the gap between the cylinders: the area of strong dipole-dipole interaction between magnetite particles 041,2. For areas with high flow losses in viscous friction is shown the possibility of reducing the introduction of magnetic fluid of carbon nanotubes and creating a rotating magnetic field.
Boundary control of fluid flow through porous media
Hasan, Agus; Foss, Bjarne; Sagatun, Svein Ivar
2010-01-01
The flow of fluids through porous media can be described by the Boussinesq’s equation with mixed boundary conditions; a Neumann’s boundary condition and a nonlinear boundary condition. The nonlinear boundary condition provides a means to control the fluid flow through porous media. In this paper,......, some stabilizing controllers are constructed for various cases using Lyapunov design....
Simulations of flow induced ordering in viscoelastic fluids
Santos de Oliveira, I.S.
2012-01-01
In this thesis we report on simulations of colloidal ordering phenomena in shearthinning viscoelastic fluids under shear flow. Depending on the characteristics of the fluid, the colloids are observed to align in the direction of the flow. These string-like structures remain stable as long as the she
Working fluid flow visualization in gravity heat pipe
Nemec Patrik
2016-01-01
Full Text Available Heat pipe is device working with phase changes of working fluid inside hermetically closed pipe at specific pressure. The phase changes of working fluid from fluid to vapour and vice versa help heat pipe to transport high heat flux. The article deal about gravity heat pipe construction and processes casing inside during heat pipe operation. Experiment working fluid flow visualization is performed with two glass heat pipes with different inner diameter (13 mm and 22 mm and filled with water. The working fluid flow visualization explains the phenomena as a working fluid boiling, nucleation of bubbles, and vapour condensation on the wall, vapour and condensate flow interaction, flow down condensate film thickness on the wall occurred during the heat pipe operation.
Working fluid flow visualization in gravity heat pipe
Nemec, Patrik; Malcho, Milan
2016-03-01
Heat pipe is device working with phase changes of working fluid inside hermetically closed pipe at specific pressure. The phase changes of working fluid from fluid to vapour and vice versa help heat pipe to transport high heat flux. The article deal about gravity heat pipe construction and processes casing inside during heat pipe operation. Experiment working fluid flow visualization is performed with two glass heat pipes with different inner diameter (13 mm and 22 mm) and filled with water. The working fluid flow visualization explains the phenomena as a working fluid boiling, nucleation of bubbles, and vapour condensation on the wall, vapour and condensate flow interaction, flow down condensate film thickness on the wall occurred during the heat pipe operation.
Microfluidic flow switching design using volume of fluid model.
Chein, Reiyu; Tsai, S H
2004-03-01
In this study, a volume of fluid (VOF) model was employed for microfluidic switch design. The VOF model validity in predicting the interface between fluid streams with different viscosities co-flowing in a microchannel was first verified by experimental observation. It was then extended to microfluidic flow switch design. Two specific flow switches, one with a guided fluid to one of five desired outlet ports, and another with a guided fluid flows into one, two, or three outlet ports equally distributed along the outlet channel of a Y-shaped channel. The flow switching was achieved by controlling the flow rate ratios between tested and buffer fluids. The numerical results showed that the VOF model could successfully predict the flow switching phenomena in these flow switches. The numerical results also showed that the flow rate ratio required for flow switching depends on the viscosity ratio between the tested and buffer fluids. The numerical simulation was verified by experimental study and the agreement was good.
Instability criteria for steady flows of a perfect fluid.
Friedlander, Susan; Vishik, Misha M.
1992-07-01
An instability criterion based on the positivity of a Lyapunov-type exponent is used to study the stability of the Euler equations governing the motion of an inviscid incompressible fluid. It is proved that any flow with exponential stretching of the fluid particles is unstable. In the case of an arbitrary axisymmetric steady integrable flow, a sufficient condition for instability is exhibited in terms of the curvature and the geodesic torsion of a stream line and the helicity of the flow.
Thermodynamics and flow-frames for dissipative relativistic fluids
Ván, P. [Dept. of Theoretical Physics, Wigner Research Centre for Physics, Institute for Particle and Nuclear Physics, H-1525 Budapest, Konkoly Thege Miklós út 29-33, Hungary and Dept. of Energy Engineering, Budapest Univ. of Technology and Econ (Hungary); Biró, T. S. [Dept. of Theoretical Physics, Wigner Research Centre for Physics, Institute for Particle and Nuclear Physics, H-1525 Budapest, Konkoly Thege Miklós út 29-33 (Hungary)
2014-01-14
A general thermodynamic treatment of dissipative relativistic fluids is introduced, where the temperature four vector is not parallel to the velocity field of the fluid. Generic stability and kinetic equilibrium points out a particular thermodynamics, where the temperature vector is parallel to the enthalpy flow vector and the choice of the flow fixes the constitutive functions for viscous stress and heat. The linear stability of the homogeneous equilibrium is proved in a mixed particle-energy flow-frame.
Martinez, M.J.; Hopkins, P.L.; Shadid, J.N.
1997-07-01
This document reports on the accomplishments of a laboratory-directed research and development (LDRD) project whose objective was to initiate a research program for developing a fundamental understanding of multiphase multicomponent subsurface transport in heterogeneous porous media and to develop parallel processing computational tools for numerical simulation of such problems. The main achievement of this project was the successful development of a general-purpose, unstructured grid, multiphase thermal simulator for subsurface transport in heterogeneous porous media implemented for use on massively parallel (MP) computers via message-passing and domain decomposition techniques. The numerical platform provides an excellent base for new and continuing project development in areas of current interest to SNL and the DOE complex including, subsurface nuclear waste disposal and cleanup, groundwater availability and contamination studies, fuel-spill transport for accident analysis, and DNAPL transport and remediation.
Lattice Boltzmann implementation for Fluids Flow Simulation in Porous Media
Xinming Zhang
2011-06-01
Full Text Available In this paper, the lattice-Boltzmann method is developed to investigate the behavior of isothermal two-phase fluid flow in porous media. The method is based on the Shan–Chen multiphase model of nonideal fluids that allow coexistence of two phases of a single substance. We reproduce some different idealized situations (phase separation, surface tension, contact angle, pipe flow, and fluid droplet motion, et al in which the results are already known from theory or laboratory measurements and show the validity of the implementation for the physical two-phase flow in porous media. Application of the method to fluid intrusion in porous media is discussed and shows the effect of wettability on the fluid flow. The capability of reproducing critical flooding phenomena under strong wettability conditions is also proved.
Flow of viscoplastic fluids in a rotating concentric annulus
Hassager, Ole; Bittleston, Simon H.
1992-01-01
pressure gradient is small compared to the yield stress of the fluid then the full solution predicts the existence of plugs attached to the outer wall of the annulus. The slot approximation fails to predict this feature. For larger pressure gradients the two solutions are in good agreement. The analytical......A difficulty in any flow calculation with viscoplastic fluids such as Bingham fluids is the determination of possible plug zones in which no deformation occurs. This paper investigates the flow in a concentric annulus when there is both an axial and tangential flow, the tangent flow arising from...... rotation of the inner cylinder of the annulus. The flow is analyzed by considering flow in a slot, for which an analytical solution is given, and by solving the full problem numerically. It is shown that when the boundary is set in motion an applied pressure gradient will always cause flow. If the applied...
Flow and Diffusion Equations for Fluid Flow in Porous Rocks for the Multiphase Flow Phenomena
Mohammad Miyan
2015-07-01
Full Text Available The multiphase flow in porous media is a subject of great complexities with a long rich history in the field of fluid mechanics. This is a subject with important technical applications, most notably in oil recovery from petroleum reservoirs and so on. The single-phase fluid flow through a porous medium is well characterized by Darcy’s law. In the petroleum industry and in other technical applications, transport is modeled by postulating a multiphase generalization of the Darcy’s law. In this connection, distinct pressures are defined for each constituent phase with the difference known as capillary pressure, determined by the interfacial tension, micro pore geometry and surface chemistry of the solid medium. For flow rates, relative permeability is defined that relates the volume flow rate of each fluid to its pressure gradient. In the present paper, there is a derivation and analysis about the diffusion equation for the fluid flow in porous rocks and some important results have been founded. The permeability is a function of rock type that varies with stress, temperature etc., and does not depend on the fluid. The effect of the fluid on the flow rate is accounted for by the term of viscosity. The numerical value of permeability for a given rock depends on the size of the pores in the rock as well as on the degree of interconnectivity of the void space. The pressure pulses obey the diffusion equation not the wave equation. Then they travel at a speed which continually decreases with time rather than travelling at a constant speed. The results shown in this paper are much useful in earth sciences and petroleum industry.
Estimation of fluid flow fields and their stagnation points
Larsen, Rasmus
Given a temporal sequence of images of fluids we will use local polynomials to regularise obser-vations of normal flows into smooth flow fields. This technique furthermore allows us to give a qualitative local description of the flow field and to estimate the position of stagnation points...
Streamline topology: Patterns in fluid flows and their bifurcations
Brøns, Morten
2007-01-01
Using dynamical systems theory, we consider structures such as vortices and separation in the streamline patterns of fluid flows. Bifurcation of patterns under variation of external parameters is studied using simplifying normal form transformations. Flows away from boundaries, flows close to fixed...
Conjugate Compressible Fluid Flow and Heat Transfer in Ducts
Cross, M. F.
2011-01-01
A computational approach to modeling transient, compressible fluid flow with heat transfer in long, narrow ducts is presented. The primary application of the model is for analyzing fluid flow and heat transfer in solid propellant rocket motor nozzle joints during motor start-up, but the approach is relevant to a wide range of analyses involving rapid pressurization and filling of ducts. Fluid flow is modeled through solution of the spatially one-dimensional, transient Euler equations. Source terms are included in the governing equations to account for the effects of wall friction and heat transfer. The equation solver is fully-implicit, thus providing greater flexibility than an explicit solver. This approach allows for resolution of pressure wave effects on the flow as well as for fast calculation of the steady-state solution when a quasi-steady approach is sufficient. Solution of the one-dimensional Euler equations with source terms significantly reduces computational run times compared to general purpose computational fluid dynamics packages solving the Navier-Stokes equations with resolved boundary layers. In addition, conjugate heat transfer is more readily implemented using the approach described in this paper than with most general purpose computational fluid dynamics packages. The compressible flow code has been integrated with a transient heat transfer solver to analyze heat transfer between the fluid and surrounding structure. Conjugate fluid flow and heat transfer solutions are presented. The author is unaware of any previous work available in the open literature which uses the same approach described in this paper.
Instability of Taylor-Couette Flow of Electrorheological Fluid
PENG Jie; ZHU Ke-Qin
2004-01-01
A linearized instability analysis of Taylor-Couette flow between two rotating concentric cylinders of an electrorheological (ER) fluid is carried out. The ER fluid exhibits a yield stress in addition to the plastic viscosity when an extra electric-field is applied. It can be found that the yield stress plays a dual role in the flow instability.The possibility of the yield surface falling between the cylinders is analysed. Although small waves appeared on the yielded surface is considered, the yielded surface, which has been treated as a free surface, has little effect on the flow instability. The effects of axisymmetric perturbation on the flow instability are presented due to the axisymmetric of the basic flow. The parameterβ in the yield stress formula of the ER fluid is shown to have distinct effects on the flow instability characteristics.
Linear stability of plane creeping Couette flow for Burgers fluid
Kai-Xin Hu; Jie Peng; Ke-Qin Zhu
2013-01-01
It is well known that plane creeping Couette flow of UCM and Oldroy-B fluids are linearly stable.However,for Burges fluid,which includes UCM and Oldroyd-B fluids as special cases,unstable modes are detected in the present work.The wave speed,critical parameters and perturbation mode are studied for neutral waves.Energy analysis shows that the sustaining of perturbation energy in Poiseuille flow and Couette flow is completely different.At low Reynolds number limit,analytical solutions are obtained for simplified perturbation equations.The essential difference between Burgers fluid and Oldroyd-B fluid is revealed to be the fact that neutral mode exists only in the former.
Simulation of uncompressible fluid flow through a porous media
Ramirez, A. [Instituto Politecnico Nacional (SEPI-ESIQIE-IPN), Unidad Profesional Zacatenco, Laboratorio de Analisis Met. (Edif. ' Z' y Edif. ' 6' P.B.), Mexico City (Mexico)], E-mail: adaramil@yahoo.com.mx; Gonzalez, J.L. [Instituto Politecnico Nacional (SEPI-ESIQIE-IPN), Unidad Profesional Zacatenco, Laboratorio de Analisis Met. (Edif. ' Z' y Edif. ' 6' P.B.), Mexico City (Mexico); Carrillo, F. [Instituto Politecnico Nacional (SEPI-CICATA-IPN), Unidad Altamira Tamaulipas, Mexico (Mexico); Lopez, S. [Instituto Mexicano del Petroleo (I.M.P.-D.F.), Mexico (Mexico)
2009-02-28
Recently, a great interest has been focused for investigations about transport phenomena in disordered systems. One of the most treated topics is fluid flow through anisotropic materials due to the importance in many industrial processes like fluid flow in filters, membranes, walls, oil reservoirs, etc. In this work is described the formulation of a 2D mathematical model to simulate the fluid flow behavior through a porous media (PM) based on the solution of the continuity equation as a function of the Darcy's law for a percolation system; which was reproduced using computational techniques reproduced using a random distribution of the porous media properties (porosity, permeability and saturation). The model displays the filling of a partially saturated porous media with a new injected fluid showing the non-defined advance front and dispersion of fluids phenomena.
Destabilization of confined granular packings due to fluid flow
Monloubou, Martin; Sandnes, Bjørnar
2016-04-01
Fluid flow through granular materials can cause fluidization when fluid drag exceeds the frictional stress within the packing. Fluid driven failure of granular packings is observed in both natural and engineered settings, e.g. soil liquefaction and flowback of proppants during hydraulic fracturing operations. We study experimentally the destabilization and flow of an unconsolidated granular packing subjected to a point source fluid withdrawal using a model system consisting of a vertical Hele-Shaw cell containing a water-grain mixture. The fluid is withdrawn from the cell at a constant rate, and the emerging flow patterns are imaged in time-lapse mode. Using Particle Image Velocimetry (PIV), we show that the granular flow gets localized in a narrow channel down the center of the cell, and adopts a Gaussian velocity profile similar to those observed in dry grain flows in silos. We investigate the effects of the experimental parameters (flow rate, grain size, grain shape, fluid viscosity) on the packing destabilization, and identify the physical mechanisms responsible for the observed complex flow behaviour.
Drag flow analysis of Oldroyd eight constant fluid
A.M. Siddiqui
2016-09-01
Full Text Available This article presents the steady drag flow problems. The incompressible Oldroyd eight constant fluid flow is considered between two infinite parallel plates. Three flow problems including the Couette flow, Poiseuille flow and Couette–Poiseuille flow are modeled. The source term appearing in the nonlinear differential equation for each case is simplified with the application of modified homotopy perturbation method, and thus the general solution is obtained. The validity of second order approximate analytic solutions is tested with the aid of a numerical technique. The order of accuracy has been obtained in tabular form and the graphs are presented to demonstrate the difference between the three flow regimes.
Two-Fluid Equilibrium for Transonic Poloidal Flows
Guazzotto, Luca; Betti, Riccardo
2012-03-01
Much analytical and numerical work has been done in the past on ideal MHD equilibrium in the presence of macroscopic flow. In recent years, several authors have worked on equilibrium formulations for a two-fluid system, in which inertial ions and massless electrons are treated as distinct fluids. In this work, we present our approach to the formulation of the two-fluid equilibrium problem. Particular attention is given to the relation between the two-fluid equations and the equilibrium equations for the single-fluid ideal MHD system. Our purpose is to reconsider the results of one-fluid calculation with the more accurate two-fluid model, referring in particular to the so-called transonic discontinuities, which occur when the poloidal velocity spans a range crossing the poloidal sound speed (i.e., the sound speed reduced by a factor Bp/B). It is expected that the one-fluid discontinuity will be resolved into a sharp gradient region by the two-fluid model. Also, contrary to the ideal MHD case, in the two-fluid model the equations governing the equilibrium are elliptic in the whole range of interest for transonic equilibria. The numerical solution of the two-fluid system of equations is going to be based on a code built on the structure of the existing ideal-MHD code FLOW.
Hunt, J. C. R.
1981-05-01
The ways in which advances in fluid mechanics have led to improvements in engineering design are discussed, with attention to the stimulation of fluid mechanics research by industrial and environmental problems. The development of many practical uses of fluid flow without the benefit of scientific study is also emphasized. Among the topics discussed are vortices and coherent structures in turbulent flows, lubrication, jet and multiphase flows, the control and exploitation of waves, the effect of unsteady forces on structures, and dispersion phenomena. Among the practical achievements covered are the use of bluff shields to control separated flow over truck bodies and reduce aerodynamic drag, ink-jet printing, hovercraft stability, fluidized-bed combustion, the fluid/solid instabilities caused by air flow around a computer memory floppy disc, and various wind turbines.
Superconfinement tailors fluid flow at microscales.
Setu, Siti Aminah
2015-06-15
Understanding fluid dynamics under extreme confinement, where device and intrinsic fluid length scales become comparable, is essential to successfully develop the coming generations of fluidic devices. Here we report measurements of advancing fluid fronts in such a regime, which we dub superconfinement. We find that the strong coupling between contact-line friction and geometric confinement gives rise to a new stability regime where the maximum speed for a stable moving front exhibits a distinctive response to changes in the bounding geometry. Unstable fronts develop into drop-emitting jets controlled by thermal fluctuations. Numerical simulations reveal that the dynamics in superconfined systems is dominated by interfacial forces. Henceforth, we present a theory that quantifies our experiments in terms of the relevant interfacial length scale, which in our system is the intrinsic contact-line slip length. Our findings show that length-scale overlap can be used as a new fluid-control mechanism in strongly confined systems.
Ultrasonic Doppler Velocity Profiler for Fluid Flow
2012-01-01
The ultrasonic velocity profile (UVP) method, first developed in medical engineering, is now widely used in clinical settings. The fluid mechanical basis of UVP was established in investigations by the author and his colleagues with work demonstrating that UVP is a powerful new tool in experimental fluid mechanics. There are diverse examples, ranging from problems in fundamental fluid dynamics to applied problems in mechanical, chemical, nuclear, and environmental engineering. In all these problems, the methodological principle in fluid mechanics was converted from point measurements to spatio-temporal measurements along a line. This book is the first monograph on UVP that offers comprehensive information about the method, its principles, its practice, and applied examples, and which serves both current and new users. Current users can confirm that their application configurations are correct, which will help them to improve the configurations so as to make them more efficient and effective. New users will be...
Superconfinement tailors fluid flow at microscales
Setu, Siti Aminah; Dullens, Roel P.A.; Hernández-Machado, Aurora; Pagonabarraga, Ignacio; Aarts, Dirk G.A.L.; Ledesma-Aguilar, Rodrigo
2015-01-01
Understanding fluid dynamics under extreme confinement, where device and intrinsic fluid length scales become comparable, is essential to successfully develop the coming generations of fluidic devices. Here we report measurements of advancing fluid fronts in such a regime, which we dub superconfinement. We find that the strong coupling between contact-line friction and geometric confinement gives rise to a new stability regime where the maximum speed for a stable moving front exhibits a distinctive response to changes in the bounding geometry. Unstable fronts develop into drop-emitting jets controlled by thermal fluctuations. Numerical simulations reveal that the dynamics in superconfined systems is dominated by interfacial forces. Henceforth, we present a theory that quantifies our experiments in terms of the relevant interfacial length scale, which in our system is the intrinsic contact-line slip length. Our findings show that length-scale overlap can be used as a new fluid-control mechanism in strongly confined systems. PMID:26073752
A two-fluid model for avalanche and debris flows.
Pitman, E Bruce; Le, Long
2005-07-15
Geophysical mass flows--debris flows, avalanches, landslides--can contain O(10(6)-10(10)) m(3) or more of material, often a mixture of soil and rocks with a significant quantity of interstitial fluid. These flows can be tens of meters in depth and hundreds of meters in length. The range of scales and the rheology of this mixture presents significant modelling and computational challenges. This paper describes a depth-averaged 'thin layer' model of geophysical mass flows containing a mixture of solid material and fluid. The model is derived from a 'two-phase' or 'two-fluid' system of equations commonly used in engineering research. Phenomenological modelling and depth averaging combine to yield a tractable set of equations, a hyperbolic system that describes the motion of the two constituent phases. If the fluid inertia is small, a reduced model system that is easier to solve may be derived.
Flow of viscoplastic fluids in eccentric annular geometries
Szabo, Peter; Hassager, Ole
1992-01-01
A classification of flowfields for the flow of a Bingham fluid in general eccentric annular geometries is presented. Simple arguments show that a singularity can exist in the stress gradient on boundaries between zones with yielded and un-yielded fluid respectively. A Finite Element code is used...... to verify this property of the Bingham fluid. An analytical solution for the flowfield in case of small eccentricities is derived....
Chen, Li; Tang, Qing; Robinson, Bruce A; He, Ya-Ling; Tao, Wen-Quan
2014-01-01
Multicomponent multiphase reactive transport processes with dissolution-precipitation are widely encountered in energy and environment systems. A pore-scale two-phase multi-mixture model based on the lattice Boltzmann method (LBM) is developed for such complex transport processes, where each phase is considered as a mixture of miscible components in it. The liquid-gas fluid flow with large density ratio is simulated using the multicomponent multiphase pseudo-potential LB model; the transport of certain solute in the corresponding solvent is solved using the mass transport LB model; and the dynamic evolutions of the liquid-solid interface due to dissolution-precipitation are captured by an interface tracking scheme. The model developed can predict coupled multiple physicochemical processes including multiphase flow, multicomponent mass transport, homogeneous reactions in the bulk fluid and heterogeneous dissolution-precipitation reactions at the fluid-solid interface, and dynamic evolution of the solid matrix ...
Thermo-Fluid Dynamics of Two-Phase Flow
Ishii, Mamrou
2011-01-01
"Thermo-fluid Dynamics of Two-Phase Flow, Second Edition" is focused on the fundamental physics of two-phase flow. The authors present the detailed theoretical foundation of multi-phase flow thermo-fluid dynamics as they apply to: Nuclear reactor transient and accident analysis; Energy systems; Power generation systems; Chemical reactors and process systems; Space propulsion; Transport processes. This edition features updates on two-phase flow formulation and constitutive equations and CFD simulation codes such as FLUENT and CFX, new coverage of the lift force model, which is of part
Generation of zonal flows in rotating fluids and magnetized plasmas
Juul Rasmussen, J.; Garcia, O.E.; Naulin, V.
2006-01-01
contribution the generation of zonal flows will be illustrated in a simple fluid experiment performed in a rotating container with radial symmetric bottom topography. An effective mixing that homogenizes the potential vorticity in the fluid layer will lead to the replacement of the high-potential vorticity...
A variational approach to estimate incompressible fluid flows
2017-02-01
A variational approach is used to recover fluid motion governed by Stokes and Navier–Stokes equations. Unlike previous approaches where optical flow method is used to track rigid body motion, this new framework aims at investigating incompressible flows using optical flow techniques. We formulate a minimization problem and determine conditions under which unique solution exists. Numerical results using finite element method not only support theoretical results but also show that Stokes flow forced by a potential are recovered almost exactly.
EXACT SOLUTIONS FOR MAGNETOHYDRODYNAMIC FLOW IN A ROTATING FLUID
S.Asghar; Masood Khan; A.M.Siddiqui; T.Hayat
2002-01-01
An analytical solution is obtained for the flow due to solid-body rotations of an oscillating porous disk and of a fluid at infinity. Neglecting the induced magnetic field, the effects of the transversely applied magnetic field on the flow are studied. Further, the flow confined between two disks is also discussed. It is found that an infinite number of solutions exist for the flow confined between two disks.
Near critical swirling flow of a viscoelastic fluid
Ly, Nguyen; Rusak, Zvi; Tichy, John; Wang, Shixiao
2016-11-01
The interaction between flow inertia and elasticity in high Re, axisymmetric, and near-critical swirling flows of a viscoelastic fluid in a finite-length straight circular pipe is studied. The viscous stresses are described by the Giesekus constitutive model. The application of this model to columnar streamwise vortices is first investigated. Then, a nonlinear small-disturbance analysis is developed from the governing equations of motion. It explores the complicated interactions between flow inertia, swirl, and fluid viscosity and elasticity. An effective Re that links between steady states of swirling flows of a viscoelastic fluid and those of a Newtonian fluid is revealed. The effects of the fluid viscosity, relaxation time, retardation time and mobility parameter on the flow development and on the critical swirl for the appearance of vortex breakdown are explored. Decreasing the ratio of the viscoelastic characteristic times from one increases the critical swirl for breakdown. Increasing the Weissenberg number from zero or increasing the fluid mobility parameter from zero cause a similar effect. Results may explain changes in the appearance of breakdown zones as a function of swirl level that were observed in Stokes et al. (2001) experiments, where Boger fluids were used.
Viscoelastic fluid-structure interaction between a non-Newtonian fluid flow and flexible cylinder
Dey, Anita; Modarres-Sadeghi, Yahya; Rothstein, Jonathan
2016-11-01
It is well known that when a flexible or flexibly-mounted structure is placed perpendicular to the flow of a Newtonian fluid, it can oscillate due to the shedding of separated vortices at high Reynolds numbers. If the same flexible object is placed in non-Newtonian flows, however, the structure's response is still unknown. Unlike Newtonian fluids, the flow of viscoelastic fluids can become unstable at infinitesimal Reynolds numbers due to a purely elastic flow instability. In this talk, we will present a series of experiments investigating the response of a flexible cylinder placed in the cross flow of a viscoelastic fluid. The elastic flow instabilities occurring at high Weissenberg numbers can exert fluctuating forces on the flexible cylinder thus leading to nonlinear periodic oscillations of the flexible structure. These oscillations are found to be coupled to the time-dependent state of viscoelastic stresses in the wake of the flexible cylinder. The static and dynamic responses of the flexible cylinder will be presented over a range of flow velocities, along with measurements of velocity profiles and flow-induced birefringence, in order to quantify the time variation of the flow field and the state of stress in the fluid.
Deployable Emergency Shutoff Device Blocks High-Velocity Fluid Flows
Nabors, Sammy A.
2015-01-01
NASA's Marshall Space Flight Center has developed a device and method for blocking the flow of fluid from an open pipe. Motivated by the sea-bed oil-drilling catastrophe in the Gulf of Mexico in 2010, NASA innovators designed the device to plug, control, and meter the flow of gases and liquids. Anchored with friction fittings, spikes, or explosively activated fasteners, the device is well-suited for harsh environments and high fluid velocities and pressures. With the addition of instrumentation, it can also be used as a variable area flow metering valve that can be set based upon flow conditions. With robotic additions, this patent-pending innovation can be configured to crawl into a pipe then anchor and activate itself to block or control fluid flow.
Optimum solar collector fluid flow rates
Furbo, Simon; Shah, Louise Jivan
1996-01-01
the energy consumption of a normal ciculation pump in the solar heating system.Calculations showed that the highest thermal performances for small SDHW systems based on mantle tanks with constant volume flow rates in the solar collector loops are achieved if the flow rate is situated in the interval from 0...... to the temperature difference between the solar collector and the bottom of the mantle - an increase of about 1% of the thermal performance is possible.Finally, calculations showed that the highest thermal performance for large SDHW systems with constant volume flow rates in the solar collector loops are achieved....... The flow rate is increasing for increasing temperature.The flow rate at the high temperature level is typically 70 % greater than the flow rate at the low temperature level.Further, the energy consumption for the electronically controlled pump in a solar heating system will be somewhat smaller than...
Surface tension driven flow in glass melts and model fluids
Mcneil, T. J.; Cole, R.; Subramanian, R. S.
1982-01-01
Surface tension driven flow has been investigated analytically and experimentally using an apparatus where a free column of molten glass or model fluids was supported at its top and bottom faces by solid surfaces. The glass used in the experiments was sodium diborate, and the model fluids were silicone oils. In both the model fluid and glass melt experiments, conclusive evidence was obtained to prove that the observed flow was driven primarily by surface tension forces. The experimental observations are in qualitative agreement with predictions from the theoretical model.
Progress in modeling of fluid flows in crystal growth processes
Qisheng Chen; Yanni Jiang; Junyi Yan; Ming Qin
2008-01-01
Modeling of fluid flows in crystal growth processes has become an important research area in theoretical and applied mechanics.Most crystal growth processes involve fluid flows,such as flows in the melt,solution or vapor.Theoretical modeling has played an important role in developing technologies used for growing semiconductor crystals for high performance electronic and optoelectronic devices.The application of devices requires large diameter crystals with a high degree of crystallographic perfection,low defect density and uniform dopant distribution.In this article,the flow models developed in modeling of the crystal growth processes such as Czochralski,ammono-thermal and physical vapor transport methods are reviewed.In the Czochralski growth modeling,the flow models for thermocapillary flow,turbulent flow and MHD flow have been developed.In the ammonothermal growth modeling,the buoyancy and porous media flow models have been developed based on a single-domain and continuum approach for the composite fluid-porous layer systems.In the physical vapor transport growth modeling,the Stefan flow model has been proposed based on the flow-kinetics theory for the vapor growth.In addition,perspectives for future studies on crystal growth modeling are proposed.
Numerical modeling of fluid flow with rafts: An application to lava flows
Tsepelev, Igor; Ismail-Zadeh, Alik; Melnik, Oleg; Korotkii, Alexander
2016-07-01
Although volcanic lava flows do not significantly affect the life of people, its hazard is not negligible as hot lava kills vegetation, destroys infrastructure, and may trigger a flood due to melting of snow/ice. The lava flow hazard can be reduced if the flow patterns are known, and the complexity of the flow with debris is analyzed to assist in disaster risk mitigation. In this paper we develop three-dimensional numerical models of a gravitational flow of multi-phase fluid with rafts (mimicking rigid lava-crust fragments) on a horizontal and topographic surfaces to explore the dynamics and the interaction of lava flows. We have obtained various flow patterns and spatial distribution of rafts depending on conditions at the surface of fluid spreading, obstacles on the way of a fluid flow, raft landing scenarios, and the size of rafts. Furthermore, we analyze two numerical models related to specific lava flows: (i) a model of fluid flow with rafts inside an inclined channel, and (ii) a model of fluid flow from a single vent on an artificial topography, when the fluid density, its viscosity, and the effusion rate vary with time. Although the studied models do not account for lava solidification, crust formation, and its rupture, the results of the modeling may be used for understanding of flows with breccias before a significant lava cooling.
Distributed thermal micro sensors for fluid flow
Baar, van John Joannes Jacobus
2002-01-01
In this thesis the framework of thermal sensor-actuator structures is proposed for measuring the parameters pressure p, dynamic viscosity μ, thermal conductivity , specific heat c, density and fluid velocity v. All structures are based on simple resistive elements that can be used as actuator and s
Fluid flows in a librating cylinder
Sauret, Alban; Bars, Michael Le; Dizès, Stéphane Le; 10.1063/1.3680874
2012-01-01
The flow in a cylinder driven by time harmonic oscillations of the rotation rate, called longitudinal librations, is investigated. Using a theoretical approach and axisymmetric numerical simulations, we study two distinct phenomena appearing in this librating flow. First, we investigate the occurrence of a centrifugal instability near the oscillating boundary, leading to the so-called Taylor-G\\"ortler vortices. A viscous stability criterion is derived and compared to numerical results obtained for various libration frequencies and Ekman numbers. The strongly nonlinear regime well above the instability threshold is also documented. We show that a new mechanism of spontaneous generation of inertial waves in the bulk could exist when the sidewall boundary layer becomes turbulent. Then, we analyse the librating flow below the instability threshold and characterize the mean zonal flow correction induced by the nonlinear interaction of the boundary layer flow with itself. In the frequency regime where inertial mode...
Flow networks: A characterization of geophysical fluid transport
Ser-Giacomi, Enrico; Lopez, Cristobal; Hernandez-Garcia, Emilio
2014-01-01
We represent transport between different regions of a fluid domain by flow networks, constructed from the discrete representation of the Perron-Frobenius or transfer operator associated to the fluid advection dynamics. The procedure is useful to analyze fluid dynamics in geophysical contexts, as illustrated by the construction of a flow network associated to the surface circulation in the Mediterranean sea. We use network-theory tools to analyze the flow network and gain insights into transport processes. In particular we quantitatively relate dispersion and mixing characteristics, classically quantified by Lyapunov exponents, to the degree of the network nodes. A family of network entropies is defined from the network adjacency matrix, and related to the statistics of stretching in the fluid, in particular to the Lyapunov exponent field. Finally we use a network community detection algorithm, Infomap, to partition the Mediterranean network into coherent regions, i.e. areas internally well mixed, but with lit...
Characterization and Low-Dimensional Modeling of Urban Fluid Flow
2014-10-06
dimensional description of this urban flow. On the computational side, a new spectral -element code was developed that was demonstrated to produce accurate...contaminant transport. 15. SUBJECT TERMS Urban fluid flow, Spectral element method, Particle Image Velocitmetry 16. SECURITY CLASSIFICATION OF: 17...number and part number, if applicable. On classified documents, enter the title classification in parentheses. 5a. CONTRACT NUMBER. Enter all
System proportions fluid-flow in response to demand signals
1966-01-01
Control system provides proportioned fluid flow rates in response to demand signals. It compares a digital signal, representing a flow demand, with a reference signal to yield a control voltage to one or more solenoid valves connected to orifices of a predetermined size.
Multiphase flow of immiscible fluids on unstructured moving meshes
Misztal, Marek Krzysztof; Erleben, Kenny; Bargteil, Adam
2012-01-01
In this paper, we present a method for animating multiphase flow of immiscible fluids using unstructured moving meshes. Our underlying discretization is an unstructured tetrahedral mesh, the deformable simplicial complex (DSC), that moves with the flow in a Lagrangian manner. Mesh optimization op...
Hydromechanical Modeling of Fluid Flow in the Lower Crust
Connolly, J.
2011-12-01
The lower crust lies within an ambiguous rheological regime between the brittle upper crust and ductile sub-lithospheric mantle. This ambiguity has allowed two schools of thought to develop concerning the nature of fluid flow in the lower crust. The classical school holds that lower crustal rocks are inviscid and that any fluid generated by metamorphic devolatilization is squeezed out of rocks as rapidly as it is produced. According to this school, permeability is a dynamic property and fluid flow is upward. In contrast, the modern school uses concepts from upper crustal hydrology that presume implicitly, if not explicitly, that rocks are rigid or, at most, brittle. For the modern school, the details of crustal permeability determine fluid flow and as these details are poorly known almost anything is possible. Reality, to the extent that it is reflected by inference from field studies, offers some support to both schools. In particular, evidence of significant lateral and channelized fluid flow are consistent with flow in rigid media, while evidence for short (104 - 105 y) grain-scale fluid-rock interaction during much longer metamorphic events, suggests that reaction-generated grain-scale permeability is sealed rapidly by compaction; a phenomenon that is also essential to prevent extensive retrograde metamorphism. These observations provide a compelling argument for recognizing in conceptual models of lower crustal fluid flow that rocks are neither inviscid nor rigid, but compact by viscous mechanisms on a finite time-scale. This presentation will review the principle consequences of, and obstacles to, incorporating compaction in such models. The role of viscous compaction in the lower crust is extraordinarily uncertain, but ignoring this uncertainty in models of lower crustal fluid flow does not make the models any more certain. Models inevitably invoke an initial steady state hydraulic regime. This initial steady state is critical to model outcomes because it
Fluid migration in the subduction zone: a coupled fluid flow approach
Wang, Hongliang; Huismans, Ritske; Rondenay, Stéphane
2016-04-01
Subduction zone are the main entry point of water into earth's mantle and play an important role in the global water cycle. The progressive release of water by metamorphic dehydration induce important physical-chemical process in the subduction zone, such as hydrous melting, hydration and weakening of the mantle wedge, creation of pore fluid pressures that may weaken the subduction interface and induce earthquakes. Most previous studies on the role of fluids in subduction zones assume vertical migration or migration according to the dynamic pressure in the solid matrix without considering the pore fluid pressure effect on the deformation of the solid matrix. Here we investigate this interaction by explicitly modeling two-phase coupled poro-plastic flow during subduction. In this approach, the fluid migrates by compaction and decompaction of the solid matrix and affects the subduction dynamics through pore fluid pressure dependent frictional-plastic yield. Our preliminary results indicate that: 1) the rate of fluid migration depends strongly on the permeability and the bulk viscosity of the solid matrix, 2) fluid transfer occurs preferentially along the slab and then propagates into the mantle wedge by viscous compaction driven fluid flow, 3) fluid transport from the surface to depth is a prerequisite for producing high fluid pore pressures and associated hydration induced weakening of the subduction zone interface.
A numerical model for dynamic crustal-scale fluid flow
Sachau, Till; Bons, Paul; Gomez-Rivas, Enrique; Koehn, Daniel
2015-04-01
Fluid flow in the crust is often envisaged and modeled as continuous, yet minimal flow, which occurs over large geological times. This is a suitable approximation for flow as long as it is solely controlled by the matrix permeability of rocks, which in turn is controlled by viscous compaction of the pore space. However, strong evidence (hydrothermal veins and ore deposits) exists that a significant part of fluid flow in the crust occurs strongly localized in both space and time, controlled by the opening and sealing of hydrofractures. We developed, tested and applied a novel computer code, which considers this dynamic behavior and couples it with steady, Darcian flow controlled by the matrix permeability. In this dual-porosity model, fractures open depending on the fluid pressure relative to the solid pressure. Fractures form when matrix permeability is insufficient to accommodate fluid flow resulting from compaction, decompression (Staude et al. 2009) or metamorphic dehydration reactions (Weisheit et al. 2013). Open fractures can close when the contained fluid either seeps into the matrix or escapes by fracture propagation: mobile hydrofractures (Bons, 2001). In the model, closing and sealing of fractures is controlled by a time-dependent viscous law, which is based on the effective stress and on either Newtonian or non-Newtonian viscosity. Our simulations indicate that the bulk of crustal fluid flow in the middle to lower upper crust is intermittent, highly self-organized, and occurs as mobile hydrofractures. This is due to the low matrix porosity and permeability, combined with a low matrix viscosity and, hence, fast sealing of fractures. Stable fracture networks, generated by fluid overpressure, are restricted to the uppermost crust. Semi-stable fracture networks can develop in an intermediate zone, if a critical overpressure is reached. Flow rates in mobile hydrofractures exceed those in the matrix porosity and fracture networks by orders of magnitude
Modelling fluid flow in a reciprocating compressor
Tuhovcak Jan
2015-01-01
Full Text Available Efficiency of reciprocating compressor is strongly dependent on the valves characteristics, which affects the flow through the suction and discharge line. Understanding the phenomenon inside the compressor is necessary step in development process. Commercial CFD tools offer wide capabilities to simulate the flow inside the reciprocating compressor, however they are too complicated in terms of computational time and mesh creation. Several parameters describing compressor could be therefore examined without the CFD analysis, such is valve characteristic, flow through the cycle and heat transfer. The aim of this paper is to show a numerical tool for reciprocating compressor based on the energy balance through the cycle, which provides valve characteristics, flow through the cycle and heat losses from the cylinder. Spring-damping-mass model was used for the valve description. Boundary conditions were extracted from the performance test of 4-cylinder semihermetic compressor and numerical tool validation was performed with indicated p-V diagram comparison.
Modelling fluid flow in a reciprocating compressor
Tuhovcak, Jan; Hejčík, Jiří; Jícha, Miroslav
2015-05-01
Efficiency of reciprocating compressor is strongly dependent on the valves characteristics, which affects the flow through the suction and discharge line. Understanding the phenomenon inside the compressor is necessary step in development process. Commercial CFD tools offer wide capabilities to simulate the flow inside the reciprocating compressor, however they are too complicated in terms of computational time and mesh creation. Several parameters describing compressor could be therefore examined without the CFD analysis, such is valve characteristic, flow through the cycle and heat transfer. The aim of this paper is to show a numerical tool for reciprocating compressor based on the energy balance through the cycle, which provides valve characteristics, flow through the cycle and heat losses from the cylinder. Spring-damping-mass model was used for the valve description. Boundary conditions were extracted from the performance test of 4-cylinder semihermetic compressor and numerical tool validation was performed with indicated p-V diagram comparison.
Fluid dynamics: Water flows out of touch
Hof, Björn
2017-01-01
Superhydrophobic surfaces reduce the frictional drag between water and solid materials, but this effect is often temporary. The realization of sustained drag reduction has applications for water vehicles and pipeline flows.
Direct numerical simulation of solidification microstructures affected by fluid flow
Juric, D.
1997-12-01
The effects of fluid flow on the solidification morphology of pure materials and solute microsegregation patterns of binary alloys are studied using a computational methodology based on a front tracking/finite difference method. A general single field formulation is presented for the full coupling of phase change, fluid flow, heat and solute transport. This formulation accounts for interfacial rejection/absorption of latent heat and solute, interfacial anisotropies, discontinuities in material properties between the liquid and solid phases, shrinkage/expansion upon solidification and motion and deformation of the solid. Numerical results are presented for the two dimensional dendritic solidification of pure succinonitrile and the solidification of globulitic grains of a plutonium-gallium alloy. For both problems, comparisons are made between solidification without fluid flow and solidification within a shear flow.
Friedman, Morton H; Krams, Rob; Chandran, Krishnan B
2010-03-01
Interactions between flow and biological cells and tissues are intrinsic to the circulatory, respiratory, digestive and genitourinary systems. In the circulatory system, an understanding of the complex interaction between the arterial wall (a living multi-component organ with anisotropic, nonlinear material properties) and blood (a shear-thinning fluid with 45% by volume consisting of red blood cells, platelets, and white blood cells) is vital to our understanding of the physiology of the human circulation and the etiology and development of arterial diseases, and to the design and development of prosthetic implants and tissue-engineered substitutes. Similarly, an understanding of the complex dynamics of flow past native human heart valves and the effect of that flow on the valvular tissue is necessary to elucidate the etiology of valvular diseases and in the design and development of valve replacements. In this paper we address the influence of biomechanical factors on the arterial circulation. The first part presents our current understanding of the impact of blood flow on the arterial wall at the cellular level and the relationship between flow-induced stresses and the etiology of atherosclerosis. The second part describes recent advances in the application of fluid-structure interaction analysis to arterial flows and the dynamics of heart valves.
Heat transfer and fluid flow in minichannels and microchannels
Kandlikar, Satish; Li, Dongqing; Colin, Stephane; King, Michael R
2013-01-01
Heat exchangers with minichannel and microchannel flow passages are becoming increasingly popular due to their ability to remove large heat fluxes under single-phase and two-phase applications. Heat Transfer and Fluid Flow in Minichannels and Microchannels methodically covers gas, liquid, and electrokinetic flows, as well as flow boiling and condensation, in minichannel and microchannel applications. Examining biomedical applications as well, the book is an ideal reference for anyone involved in the design processes of microchannel flow passages in a heat exchanger. Each chapter is accompan
Active Learning in Fluid Mechanics: Youtube Tube Flow and Puzzling Fluids Questions
Hrenya, Christine M.
2011-01-01
Active-learning exercises appropriate for a course in undergraduate fluid mechanics are presented. The first exercise involves an experiment in gravity-driven tube flow, with small groups of students partaking in a contest to predict the experimental flow rates using the mechanical energy balance. The second exercise takes the form of an…
Active Learning in Fluid Mechanics: Youtube Tube Flow and Puzzling Fluids Questions
Hrenya, Christine M.
2011-01-01
Active-learning exercises appropriate for a course in undergraduate fluid mechanics are presented. The first exercise involves an experiment in gravity-driven tube flow, with small groups of students partaking in a contest to predict the experimental flow rates using the mechanical energy balance. The second exercise takes the form of an…
The fluid mechanics of continuous flow electrophoresis
Saville, D. A.
1990-01-01
The overall objective is to establish theoretically and confirm experimentally the ultimate capabilities of continuous flow electrophoresis chambers operating in an environment essentially free of particle sedimentation and buoyancy. The efforts are devoted to: (1) studying the effects of particle concentration on sample conductivity and dielectric constant. The dielectric constant and conductivity were identified as playing crucial roles in the behavior of the sample and on the resolving power and throughput of continuous flow devices; and (2) improving the extant mathematical models to predict flow fields and particle trajectories in continuous flow electrophoresis. A dielectric spectrometer was designed and built to measure the complex dielectric constant of a colloidal dispersion as a function of frequency between 500 Hz and 200 kHz. The real part of the signal can be related to the sample's conductivity and the imaginary part to its dielectric constant. Measurements of the dielectric constants of several different dispersions disclosed that the dielectric constants of dilute systems of the sort encountered in particle electrophoresis are much larger than would be expected based on the extant theory. Experiments were carried out to show that, in many cases, this behavior is due to the presence of a filamentary structure of small hairs on the particle surface. A technique for producing electrokinetically ideal synthetic latex particles by heat treating was developed. Given the ubiquitous nature of hairy surfaces with both cells and synthetic particles, it was deemed necessary to develop a theory to explain their behavior. A theory for electrophoretic mobility of hairy particles was developed. Finally, the extant computer programs for predicting the structure of electro-osmotically driven flows were extended to encompass flow channels with variable wall mobilities.
黄世军; 李秋; 程林松; 朱国金; 张萌
2015-01-01
稠油储量占渤海总石油储量的60%，是中国石油接替储量的重要组成部分。多元热流体的应用克服了海上平台承载能力有限的难题，是海上稠油热采的新方向。首次考虑井口注入条件变化及海水流动的影响，以一段时间内注入到管线中的多元热流体为控制体，分别考虑平台、海水段和地层注汽管柱结构的影响，建立了多组分热流体沿程热物性评价模型。计算结果与中国某油田实际热采井沿程热物性参数吻合较好。基于模块计算，评价了多元热流体组成，海水深度对其沿程热利用率的影响，为多元热流体在海上稠油油藏热采中的应用提供了一定的理论支持。%Heavy oil covers about 60%of the total reserve in Bohai Bay,which is a significant part in the succeeding petroleum industry in China. The application of multi-component heat fluid(MCHF)overcomes the problem of limited load of offshore platforms,serving as a new break through in offshore oil production. Considering the impact of various injection conditions and sea water flow for the first time,the model takes the amount of fluid injected within a certain period of time as control volume and concludes the influence of pipeline structures of platform,sea water section and sub-surface section. With Visual Basic program language,the results of the model show a good agreement with the field test data. Based on the model,the impact of the composition of multi-component heat fluid and the depth of sea water on the efficiency along the injection line are studied. Curves and conclusions of this essay would provide some support for the application of this new technology.
Topological Fluid Mechanics with Applications to Free Surfaces and Axisymmetric Flows
Brøns, Morten
1996-01-01
Topological fluid mechanics is the study of qualitative features of fluid patterns. We discuss applications to the flow beneath a stagnant surface film, and to patterns in axisymmetric flow.......Topological fluid mechanics is the study of qualitative features of fluid patterns. We discuss applications to the flow beneath a stagnant surface film, and to patterns in axisymmetric flow....
Network-Theoretic Modeling of Fluid Flow
2015-07-29
connections. Identifying such locations is especially critical when containment 3 measures are designed to control outbreaks of HIV [5], SARS [6...intuitive explanation that turbulent flows will be resilient against small-scale forcing while the global behavior can be easily modified by large-scale
On statistical equilibrium in helical fluid flows
M. V. Kurgansky
2006-01-01
Full Text Available The statistical mechanics of 3-D helical flows is re-examined for a continuum truncated at a top wavenumber. Based on the principle of equipartition of the flow enstrophy between helical modes, the emerging (i energy spectrum law '–2' and (ii formal mathematical analogy between the helicity and the thermodynamic entropy are discussed. It is noted that the '–2' scaling law is consistent with both spectral equilibrium and spectral cascade paradigms. In an attempt to apply the obtained results to a turbulent flow regime within the Earth's outer liquid core, where the net helicity of a turbulent flow component is presumably explained by Earth's rotation, it has been noticed that it is the energy spectral law '–1', but not '–2', which is likely realized there and within the logarithmic accuracy corresponds to the case of the velocity structure function [u(l]2 independency on the spatial scale l, the latter is consistent with observations. It is argued that the '–1' scaling law can also be interpreted in terms of the spectral equilibrium and it is emphasized that the causes of the likely dominance of the spectral law '–1' over the spectral law '–2' in this geophysical application deserve further investigation and clarification.
Optimization of micropillar sequences for fluid flow sculpting
Stoecklein, Daniel; Kim, Dongyuk; Di Carlo, Dino; Ganapathysubramanian, Baskar
2015-01-01
Inertial fluid flow deformation around pillars in a microchannel is a new method for controlling fluid flow. Sequences of pillars have been shown to produce a rich phase space with a wide variety of flow transformations. Previous work has successfully demonstrated manual design of pillar sequences to achieve desired transformations of the flow cross-section, with experimental validation. However, such a method is not ideal for seeking out complex sculpted shapes as the search space quickly becomes too large for efficient manual discovery. We explore fast, automated optimization methods to solve this problem. We formulate the inertial flow physics in microchannels with different micropillar configurations as a set of state transition matrix operations. These state transition matrices are constructed from experimentally validated streamtraces. This facilitates modeling the effect of a sequence of micropillars as nested matrix-matrix products, which have very efficient numerical implementations. With this new fo...
Fluid flow sensing with ionic polymer-metal composites
Stalbaum, Tyler; Trabia, Sarah; Shen, Qi; Kim, Kwang J.
2016-04-01
Ionic polymer-metal composite (IPMC) actuators and sensors have been developed and modeled over the last two decades for use as soft-robotic deformable actuators and sensors. IPMC devices have been suggested for application as underwater actuators, energy harvesting devices, and medical devices such as in guided catheter insertion. Another interesting application of IPMCs in flow sensing is presented in this study. IPMC interaction with fluid flow is of interest to investigate the use of IPMC actuators as flow control devices and IPMC sensors as flow sensing devices. An organized array of IPMCs acting as interchanging sensors and actuators could potentially be designed for both flow measurement and control, providing an unparalleled tool in maritime operations. The underlying physics for this system include the IPMC ion transport and charge fundamental framework along with fluid dynamics to describe the flow around IPMCs. An experimental setup for an individual rectangular IPMC sensor with an externally controlled fluid flow has been developed to investigate this phenomenon and provide further insight into the design and application of this type of device. The results from this portion of the study include recommendations for IPMC device designs in flow control.
Computerized tomographic analysis of fluid flow in fractured tuff
Felice, C.W.; Sharer, J.C. (Terra Tek, Inc., Salt Lake City, UT (United States)); Springer, E.P. (Los Alamos National Lab., NM (United States))
1992-01-01
The purpose of this summary is to demonstrate the usefulness of X-ray computerized tomography to observe fluid flow down a fracture and rock matrix imbibition in a sample of Bandelier tuff. This was accomplished by using a tuff sample 152.4 mm long and 50.8 mm in diameter. A longitudinal fracture was created by cutting the core with a wire saw. The fractured piece was then coupled to its adjacent section to that the fracture was not expected. Water was injected into a dry sample at five flow rates and CT scanning performed at set intervals during the flow. Cross sectional images and longitudinal reconstructions were built and saturation profiles calculated for the sample at each time interval at each flow rate. The results showed that for the test conditions, the fracture was not a primary pathway of fluid flow down the sample. At a slow fluid injection rate into the dry sample, the fluid was imbibed into the rock uniformly down the length of the core. With increasing injection rates, the flow remained uniform over the core cross section through complete saturation.
Vertically aligned carbon nanotubes for sensing unidirectional fluid flow
Kiani, Keivan, E-mail: k_kiani@kntu.ac.ir
2015-05-15
From applied mechanics points of view, potential application of ensembles of single-walled carbon nanotubes (SWCNTs) as fluid flow sensors is aimed to be examined. To this end, useful nonlocal analytical and numerical models are developed. The deflection of the ensemble of SWCNTs at the tip is introduced as a measure of its sensitivity. The influences of the length and radius of the SWCNT, intertube distance, fluid flow velocity, and distance of the ensemble from the leading edge of the rigid base on the deflection field of the ensemble are comprehensively examined. The obtained results display how calibration of an ensemble of SWCNTs can be methodically carried out in accordance with the characteristics of the ensemble and the external fluid flow.
Hornung, R.D. [Duke Univ., Durham, NC (United States)
1996-12-31
An adaptive local mesh refinement (AMR) algorithm originally developed for unsteady gas dynamics is extended to multi-phase flow in porous media. Within the AMR framework, we combine specialized numerical methods to treat the different aspects of the partial differential equations. Multi-level iteration and domain decomposition techniques are incorporated to accommodate elliptic/parabolic behavior. High-resolution shock capturing schemes are used in the time integration of the hyperbolic mass conservation equations. When combined with AMR, these numerical schemes provide high resolution locally in a more efficient manner than if they were applied on a uniformly fine computational mesh. We will discuss the interplay of physical, mathematical, and numerical concerns in the application of adaptive mesh refinement to flow in porous media problems of practical interest.
Graham, Michael
2015-11-01
Blood is a suspension of objects of various shapes, sizes and mechanical properties, whose distribution during flow is important in many contexts. Red blood cells tend to migrate toward the center of a blood vessel, leaving a cell-free layer at the vessel wall, while white blood cells and platelets are preferentially found near the walls, a phenomenon called margination that is critical for the physiological responses of inflammation and hemostasis. Additionally, drug delivery particles in the bloodstream will also undergo segregation - the influence of these phenomena on the efficacy of such particles is unknown. This talk describes efforts to gain a systematic understanding of flow-induced segregation phenomena in blood and other complex mixtures, using a combination of theory and direct simulations. Contrasts in size, deformability and shape can all lead to segregation. A kinetic theory model based on pair collisions and wall-induced hydrodynamic migration can capture the key effects observed in direct simulations, including a ``drainage transition'' in which one component is completely depleted from the bulk of the flow. Experiments performed in the laboratory of Wilbur Lam indicate the physiological and clinical importance of these observations. This talk is based upon work supported by the National Science Foundation under Grants No. CBET- 1132579 and No. CBET-1436082.
Fluid flow modeling in complex areas*, **
Poullet Pascal
2012-04-01
Full Text Available We show first results of 3D simulation of sea currents in a realistic context. We use the full Navier–Stokes equations for incompressible viscous fluid. The problem is solved using a second order incremental projection method associated with the finite volume of the staggered (MAC scheme for the spatial discretization. After validation on classical cases, it is used in a numerical simulation of the Pointe à Pitre harbour area. The use of the fictious domain method permits us to take into account the complexity of bathymetric data and allows us to work with regular meshes and thus preserves the efficiency essential for a 3D code. Dans cette étude, nous présentons les premiers résultats de simulation d’un écoulement d’un fluide incompressible visqueux dans un contexte environnemental réel. L’approche utilisée utilise une méthode de domaines fictifs pour une prise en compte d’un domaine physique tridimensionnel très irrégulier. Le schéma numérique combine un schéma de projection incrémentale et des volumes finis utilisant des volumes de contrôle adaptés à un maillage décalé. Les tests de validation sont menés pour les cas tests de la cavité double entraînée ainsi que l’écoulement dans un canal avec un obstacle placé de manière asymmétrique.
Taylor-Couette flow with radial fluid injection
Wilkinson, Nikolas; Dutcher, Cari S.
2017-08-01
Taylor-Couette cells have been shown to improve a number of industrial processes due to the wide variety of hydrodynamic flow states accessible. Traditional designs, however, limit the ability to introduce new fluids into the annulus during device operation due to geometric confinement and complexity. In this paper, a co- and counter-rotating Taylor-Couette cell with radial fluid injection has been constructed. The incorporation of 16 ports in the inner cylinder enables radial fluid injection during rotation of both cylinders. The design is also capable of continuous axial flow, enabling large injection volumes. The new inner cylinder design does not modify the critical Re for flow instabilities and can precisely inject a desired mass at a desired flow rate. A range of injection rates and masses were explored to quantify the effect of radial injection on the stability of the turbulent Taylor vortex structure. Only the highest injection rate and total mass studied (5.9 g/s, 100 g) modified the turbulent Taylor vortex structure after injection for a sustained period. The post-injection vortices remained larger than the pre-injection vortices, whereas at lower injection rates or masses, the vortex structure quickly returned to the pre-injection structure. This new system allows for in situ study of hydrodynamic effects on fluid-fluid (gas and liquid) mixing and multiphase complexation, growth, and structure. We demonstrated this new design's potential for studying the flocculation of bentonite using cationic polyacrylamide for enhancing water treatment operations.
FLUID FLOW INTERACTIONS IN OGUN RIVER, NIGERIA
Dr.Amartya Kumar Bhattacharya and G.Akin Bolaji
2010-02-01
Full Text Available Surface and groundwater interaction is an important aspect of the hydrologic cycle that borders on the watershed assessment, protection and restoration. In groundwater/surface water interactions, the groundwater component is much greater than the surface water but is much less visible and attracts less public interest. The mixing between surface and groundwater enables them to import their characteristics upon one another thereby counting a change in their parameters. Groundwater interacts with surface water in nearly all landscapes, ranging from small streams to major river valleys. Many scientists have studied the physical aspects of groundwater/surface water interactions, but it is in recent times that these interactions have been looked upon in relation to their ecological implications. With the coming of a more holistic approach to environmental flows and environmental protection, surface water/groundwater (SW/GW interactions should receive heightened attention at multidisciplinary scale and more so, by policy makers and watershed managers. It is generally understood in conceptual form that surface water therefore has the ability to enhance or detract from groundwater quality and vice versa, yet little is known about the processes by which these two entities interact (Gardener, 1988. In the past, emphasis has been placed on studying the physical and chemical effects that groundwater has on surface water but it is also important to look at the ecological role surface water and groundwater interactions can play in maintenance of environmental flows in a river basin. In area where surface water and groundwater directly interacts, the important issue commonly raised in recent times are not only concern with water quality but related with ecology and biodiversity. Therefore, there is a need for thorough understanding of the surface water and groundwater interactions within catchments so as to enhance the sustainable development and management of
Fluid flow behaviour of gas-condensate and near-miscible fluids at the pore scale
Dawe, Richard A. [Department of Chemical Engineering, University of West Indies, St. Augustine (Trinidad and Tobago); Grattoni, Carlos A. [Department of Earth Science and Engineering, Imperial College, London, SW7 2BP (United Kingdom)
2007-02-15
Retrograde condensate reservoir behaviour is complex with much of the detailed mechanisms of the multiphase fluid transport and mass transfer between the phases within the porous matrix still speculative. Visual modelling of selected processes occurring at the pore level under known and controlled boundary conditions can give an insight to fluid displacements at the core scale and help the interpretation of production behaviour at reservoir scale. Visualisation of the pore scale two-phase flow mechanisms has been studied experimentally at low interfacial tensions, < 0.5 mN/m, using a partially miscible fluid system in glass visual micro models. As the interfacial tension decreases the balance between fluid-fluid forces (interfacial, spreading and viscous) and fluid-solid interactions (wettability and viscous interactions) changes. Data measurements in the laboratory, particularly relative permeability, will therefore always be difficult especially for condensate fluids just below their dew point. What is certain is that gas production from a gas-condensate leads to condensate dropout when pressure falls below the dew point, either within the wellbore or, more importantly, in the reservoir. This paper illustrates some pore scale physics, particularly interfacial phenomena at low interfacial tension, which has relevance to appreciating the flow of condensate fluids close to their dew point either near the wellbore (which affects well productivity) or deep inside the reservoir (which affects condensate recovery). (author)
Fluid flow and heat transfer in rotating porous media
Vadasz, Peter
2016-01-01
This Book concentrates the available knowledge on rotating fluid flow and heat transfer in porous media in one single reference. Dr. Vadasz develops the fundamental theory of rotating flow and heat transfer in porous media and introduces systematic classification and identification of the relevant problems. An initial distinction between rotating flows in isothermal heterogeneous porous systems and natural convection in homogeneous non-‐isothermal porous systems provides the two major classes of problems to be considered. A few examples of solutions to selected problems are presented, highlighting the significant impact of rotation on the flow in porous media.
FLUID FLOW SEPARATION CHARACTER ON NOVEL HYBRID JOURNAL BEARING
CHEN Shujiang; LU Changhou; LI Lei
2006-01-01
The influence of the structure and running parameters of a novel spiral oil wedge hybrid journal bearing on the fluid flow trace is investigated. The governing equation of the flow trace of lubricant is set up, and the simulation is carried out by using finite difference method. The results show that the lubricant flow status and end leakage quantity are greatly influenced by spiral angle,and that the rotating speed has little influence on the flow status. With advisable geometry design,the separation of lubricant between different oil wedges can be obtained, which can decrease the temperature rise effectively.
Using artificial intelligence to control fluid flow computations
Gelsey, Andrew
1992-01-01
Computational simulation is an essential tool for the prediction of fluid flow. Many powerful simulation programs exist today. However, using these programs to reliably analyze fluid flow and other physical situations requires considerable human effort and expertise to set up a simulation, determine whether the output makes sense, and repeatedly run the simulation with different inputs until a satisfactory result is achieved. Automating this process is not only of considerable practical importance but will also significantly advance basic artificial intelligence (AI) research in reasoning about the physical world.
Analytical heat and fluid flow in microchannels and microsystems
Cotta, Renato M; Naveira-Cotta, Carolina P
2016-01-01
This book focuses on the modeling and analysis of heat and fluid flow in microchannels and micro-systems, compiling a number of analytical and hybrid numerical-analytical solutions for models that account for the relevant micro-scale effects, with the corresponding experimental analysis validation when applicable. The volume stands as the only available compilation of easy to use analytically-based solutions for micro-scale heat and fluid flow problems, that systematically incorporates the most relevant micro-scale effects into the mathematical models, followed by their physical interpretation on the micro-system behavior.
Multiphase flow of immiscible fluids on unstructured moving meshes
Misztal, Marek Krzysztof; Erleben, Kenny; Bargteil, Adam;
2012-01-01
In this paper, we present a method for animating multiphase flow of immiscible fluids using unstructured moving meshes. Our underlying discretization is an unstructured tetrahedral mesh, the deformable simplicial complex (DSC), that moves with the flow in a Lagrangian manner. Mesh optimization...... that the underlying discretization matches the physics and avoids the additional book-keeping required in grid-based methods where multiple fluids may occupy the same cell. Our Lagrangian approach naturally leads us to adopt a finite element approach to simulation, in contrast to the finite volume approaches adopted...
Stochastic analysis of particle-fluid two-phase flows
无
2000-01-01
This paper is devoted to exploring approaches to understanding the stochastic characteristics of particle-fluid two-phase flow. By quantifying the forces dominating the particle motion and modelling the less important and/or unclear forces as random forces, a stochastic differential equation is proposed to describe the complex behavior of a particle motion. An exploratory simulation has shown satisfactory agreement with phase doppler particle analyzer (PDPA) measurements, which indicates that stochastic analysis is a potential approach for revealing the details of particle-fluid flow phenomena.
ZHANG Li-feng; ZHI Jian-jun; MOU Ji-ning; CUI Jian
2005-01-01
The κ-ε two-equation model is used to simulate the fluid flow in the continuous casting tundish coupling with the effect of thermal buoyancy. The natural convection induced by the thermal buoyancy generates an upward flow pattern especially at the outlet zone, and has little effect on the fluid flow in the inlet zone. The maximum viscosity is 700 times larger than the laminar viscosity, which indicates the strong turbulent flow in the tundish. The maximum temperature difference in the whole tundish is 8.2 K. The temperature near the stopper rod and the short wall is obviously lower than that in the inlet zone. The existence of the stopper rod has a big effect on the fluid flow entering the SEN and the mold. All the characteristics of the tundish geometry should be considered to accurately simulate the fluid flow in the tundish.
A thermal stack structure for measurement of fluid flow
Zhao, Hao; Mitchell, S. J. N.; Campbell, D. H.; Gamble, Harold S.
2003-03-01
A stacked thermal structure for fluid flow sensing has been designed, fabricated, and tested. A double-layer polysilicon process was employed in the fabrication. Flow measurement is based on the transfer of heat from a temperature sensor element to the moving fluid. The undoped or lightly doped polysilicon temperature sensor is located on top of a heavily doped polysilicon heater element. A dielectric layer between the heater and the sensor elements provides both thermal coupling and electrical isolation. In comparison to a hot-wire flow sensor, the heating and sensing functions are separated, allowing the electrical characteristics of each to be optimized. Undoped polysilicon has a large temperature coefficient of resistance (TCR) up to 7 %/K and is thus a preferred material for the sensor. However, heavily doped polysilicon is preferred for the heater due to its lower resistance. The stacked flow sensor structure offers a high thermal sensitivity making it especially suitable for medical applications where the working temperatures are restricted. Flow rates of various fluids can be measured over a wide range. The fabricated flow sensors were used to measure the flow rate of water in the range μl - ml/min and gas (Helium) in the range 10 - 100ml/min.
Beyond Poiseuille: Preservation Fluid Flow in an Experimental Model
Saurabh Singh
2013-01-01
Full Text Available Poiseuille’s equation describes the relationship between fluid viscosity, pressure, tubing diameter, and flow, yet it is not known if cold organ perfusion systems follow this equation. We investigated these relationships in an ex vivo model and aimed to offer some rationale for equipment selection. Increasing the cannula size from 14 to 20 Fr increased flow rate by a mean (SD of 13 (12%. Marshall’s hyperosmolar citrate was three times less viscous than UW solution, but flows were only 45% faster. Doubling the bag pressure led to a mean (SD flow rate increase of only 19 (13%, not twice the rate. When external pressure devices were used, 100 mmHg of continuous pressure increased flow by a mean (SD of 43 (17% when compared to the same pressure applied initially only. Poiseuille’s equation was not followed; this is most likely due to “slipping” of preservation fluid within the plastic tubing. Cannula size made little difference over the ranges examined; flows are primarily determined by bag pressure and fluid viscosity. External infusor devices require continuous pressurisation to deliver high flow. Future studies examining the impact of perfusion variables on graft outcomes should include detailed equipment descriptions.
Thomsen, C; Ståhlberg, F; Stubgaard, M;
1990-01-01
An interleaved pseudocinematographic FLASH (fast low-angle shot) sequence with additional pulsed gradients for flow encoding was used to quantify cerebrospinal fluid (CSF) flow velocities and CSF production. Flow-dependent phase information was obtained by subtracting two differently encoded phase...
Fluid flow near the surface of earth's outer core
Bloxham, Jeremy; Jackson, Andrew
1991-01-01
This review examines the recent attempts at extracting information on the pattern of fluid flow near the surface of the outer core from the geomagnetic secular variation. Maps of the fluid flow at the core surface are important as they may provide some insight into the process of the geodynamo and may place useful constraints on geodynamo models. In contrast to the case of mantle convection, only very small lateral variations in core density are necessary to drive the flow; these density variations are, by several orders of magnitude, too small to be imaged seismically; therefore, the geomagnetic secular variation is utilized to infer the flow. As substantial differences exist between maps developed by different researchers, the possible underlying reasons for these differences are examined with particular attention given to the inherent problems of nonuniqueness.
Computational Fluid Dynamics Simulation of Multiphase Flow in Structured Packings
Saeed Shojaee
2012-01-01
Full Text Available A volume of fluid multiphase flow model was used to investigate the effective area and the created liquid film in the structured packings. The computational results revealed that the gas and liquid flow rates play significant roles in the effective interfacial area of the packing. In particular, the effective area increases as the flow rates of both phases increase. Numerical results were compared with the Brunazzi and SRP models, and a good agreement between them was found. Attention was given to the process of liquid film formation in both two-dimensional (2D and three-dimensional (3D models. The current study revealed that computational fluid dynamics (CFD can be used as an effective tool to provide information on the details of gas and liquid flows in complex packing geometries.
Fluid flow near the surface of earth's outer core
Bloxham, Jeremy; Jackson, Andrew
1991-01-01
This review examines the recent attempts at extracting information on the pattern of fluid flow near the surface of the outer core from the geomagnetic secular variation. Maps of the fluid flow at the core surface are important as they may provide some insight into the process of the geodynamo and may place useful constraints on geodynamo models. In contrast to the case of mantle convection, only very small lateral variations in core density are necessary to drive the flow; these density variations are, by several orders of magnitude, too small to be imaged seismically; therefore, the geomagnetic secular variation is utilized to infer the flow. As substantial differences exist between maps developed by different researchers, the possible underlying reasons for these differences are examined with particular attention given to the inherent problems of nonuniqueness.
Seals/Secondary Fluid Flows Workshop 1997; Volume I
Hendricks, Robert C. (Editor)
2006-01-01
The 1997 Conference provided discussions and data on (a) program overviews, (b) developments in seals and secondary air management systems, (c) interactive seals flows with secondary air or fluid flows and powerstream flows, (d) views of engine externals and limitations, (e) high speed engine research sealing needs and demands, and (f) a short course on engine design development margins. Sealing concepts discussed include, mechanical rim and cavity seals, leaf, finger, air/oil, rope, floating-brush, floating-T-buffer, and brush seals. Engine externals include all components of engine fluid systems, sensors and their support structures that lie within or project through the nacelle. The clean features of the nacelle belie the minefield of challenges and opportunities that lie within. Seals; Secondary air flows; Rotordynamics; Gas turbine; Aircraft; CFD; Testing; Turbomachinery
Kou, Jisheng
2016-02-25
In this paper, we propose an energy-stable evolution method for the calculation of the phase equilibria under given volume, temperature, and moles (VT-flash). An evolution model for describing the dynamics of two-phase fluid system is based on Fick’s law of diffusion for multi-component fluids and the Peng-Robinson equation of state. The mobility is obtained from diffusion coefficients by relating the gradient of chemical potential to the gradient of molar density. The evolution equation for moles of each component is derived using the discretization of diffusion equations, while the volume evolution equation is constructed based on the mechanical mechanism and the Peng-Robinson equation of state. It is proven that the proposed evolution system can well model the VT-flash problem, and moreover, it possesses the property of total energy decay. By using the Euler time scheme to discretize this evolution system, we develop an energy stable algorithm with an adaptive choice strategy of time steps, which allows us to calculate the suitable time step size to guarantee the physical properties of moles and volumes, including positivity, maximum limits, and correct definition of the Helmhotz free energy function. The proposed evolution method is also proven to be energy-stable under the proposed time step choice. Numerical examples are tested to demonstrate efficiency and robustness of the proposed method.
Fluid flow in the juxtaglomerular interstitium visualized in vivo.
Rosivall, László; Mirzahosseini, Shahrokh; Toma, Ildikó; Sipos, Arnold; Peti-Peterdi, János
2006-12-01
Earlier electron microscopy studies demonstrated morphological signs of fluid flow in the juxtaglomerular apparatus (JGA), including fenestrations of the afferent arteriole (AA) endothelium facing renin granular cells. We aimed to directly visualize fluid flow in the JGA, the putative function of the fenestrated endothelium, using intravital multiphoton microscopy of Munich-Wistar rats and C57BL6 mice. Renin content of the AA correlated strongly with the length of the fenestrated, filtering AA segment. Fluorescence of the extracellular fluid marker lucifer yellow (LY) injected into the cannulated femoral vein in bolus was followed in the renal cortex by real-time imaging. LY was detected in the interstitium around the JG AA before the plasma LY filtered into Bowman's capsule and early proximal tubule. The fluorescence intensity of LY in the JGA interstitium was 17.9 +/- 3.5% of that in the AA plasma (n = 6). The JGA fluid flow was oscillatory, consisting of two components: a fast (one every 5-10 s) and a slow (one every 45-50 s) oscillation, most likely due to the rapid transmission of both the myogenic and tubuloglomerular feedback (TGF)-mediated hemodynamic changes. LY was also detected in the distal tubular lumen about 2-5 s later than in the AA, indicating the flow of JGA interstitial fluid through the macula densa. In the isolated microperfused JGA, blocking the early proximal tubule with a micropipette caused significant increases in MD cell volume by 62 +/- 4% (n = 4) and induced dilation of the intercellular lateral spaces. In summary, significant and dynamic fluid flow exists in the JGA which may help filter the released renin into the renal interstitium (endocrine function). It may also modulate TGF and renin signals in the JGA (hemodynamic function).
Yabusaki, Steven B; Fang, Yilin; Williams, Kenneth H; Murray, Christopher J; Ward, Andy L; Dayvault, Richard D; Waichler, Scott R; Newcomer, Darrell R; Spane, Frank A; Long, Philip E
2011-11-01
Three-dimensional, coupled variably saturated flow and biogeochemical reactive transport modeling of a 2008 in situ uranium bioremediation field experiment is used to better understand the interplay of transport and biogeochemical reactions controlling uranium behavior under pulsed acetate amendment, seasonal water table variation, spatially variable physical (hydraulic conductivity, porosity) and geochemical (reactive surface area) material properties. While the simulation of the 2008 Big Rusty acetate biostimulation field experiment in Rifle, Colorado was generally consistent with behaviors identified in previous field experiments at the Rifle IFRC site, the additional process and property detail provided several new insights. A principal conclusion from this work is that uranium bioreduction is most effective when acetate, in excess of the sulfate-reducing bacteria demand, is available to the metal-reducing bacteria. The inclusion of an initially small population of slow growing sulfate-reducing bacteria identified in proteomic analyses led to an additional source of Fe(II) from the dissolution of Fe(III) minerals promoted by biogenic sulfide. The falling water table during the experiment significantly reduced the saturated thickness of the aquifer and resulted in reactants and products, as well as unmitigated uranium, in the newly unsaturated vadose zone. High permeability sandy gravel structures resulted in locally high flow rates in the vicinity of injection wells that increased acetate dilution. In downgradient locations, these structures created preferential flow paths for acetate delivery that enhanced local zones of TEAP reactivity and subsidiary reactions. Conversely, smaller transport rates associated with the lower permeability lithofacies (e.g., fine) and vadose zone were shown to limit acetate access and reaction. Once accessed by acetate, however, these same zones limited subsequent acetate dilution and provided longer residence times that resulted
A splitting technique for analytical modelling of two-phase multicomponent flow in porous media
Pires, A.P.; Bedrikovetsky, P.G.; Shapiro, Alexander
2006-01-01
In this paper we discuss one-dimensional models for two-phase Enhanced Oil Recovery (EOR) floods (oil displacement by gases, polymers, carbonized water, hot water, etc.). The main result presented here is the splitting of the EOR mathematical model into thermodynamical and hydrodynamical parts....... The introduction of a potential associated with one of the conservation laws and its use as a new independent coordinate reduces the number of equations by one. The (n)x(n) conservation law model for two-phase n-component EOR flows in new coordinates is transformed into a reduced (n-1)x(n-1) auxiliary system...... containing just thermodynamical variables (equilibrium fractions of components, sorption isotherms) and one lifting equation containing just hydrodynamical parameters (phase relative permeabilities and viscosities). The algorithm to solve analytically the problem includes solution of the reduced auxiliary...
Two-Fluid Couette Flow between Concentric Cylinders.
1984-01-01
CONCENTRIC CYLINDERS Yuriko Renardy and Daniel D. Joseph* Technical Summary Report #2622 January 1984 ABSTRACT -1W considers,he flow of two immiscible...CYLINDERS Yuriko Renardy and Daniel D. Joseph* Introduction We consider linear stability of the flow of two immiscible fluids separated by an interface...AUTiOR(,) 8. CONTRACT OR GRANT NUMBER(@) Yuriko Renardy and Daniel D. Joseph DAAGZ9-80-C-0041 11. PERFORMING ORGANIZATION NAME AND ADDRESS 10
The Finiteness of vortices in steady incompressible viscous fluid flow
Kalita, Jiten C; Panda, Swapnendu
2016-01-01
In this work, we provide two novel approaches to show that incompressible fluid flow in a finite domain contains at most a finite number vortices. We use a recently developed geometric theory of incompressible viscous flows along with an existing mathematical analysis concept to establish the finiteness. We also offer a second proof of finiteness by roping in the Kolmogorov's length scale criterion in conjunction with the notion of diametric disks.
Multiphase Flow of Immiscible Fluids on Unstructured Moving Meshes
Misztal, Marek Krzysztof; Erleben, Kenny; Bargteil, Adam;
2013-01-01
In this paper, we present a method for animating multiphase flow of immiscible fluids using unstructured moving meshes. Our underlying discretization is an unstructured tetrahedral mesh, the deformable simplicial complex (DSC), that moves with the flow in a Lagrangian manner. Mesh optimization op...... complement and solve our optimization on the GPU. We provide the results of parameter studies as well as a performance analysis of our method, together with suggestions for performance optimization....
Wave front distortion based fluid flow imaging
Iffa, Emishaw; Heidrich, Wolfgang
2013-03-01
In this paper, a transparent flow surface reconstruction based on wave front distortion is investigated. A camera lens is used to focus the image formed by the micro-lens array to the camera imaging plane. The irradiance of the captured image is transformed to frequency spectrum and then the x and y spatial components are separated. A rigid spatial translation followed by low pass filtering yields a single frequency component of the image intensity. Index of refraction is estimated from the inverse Fourier transform of the spatial frequency spectrum of the irradiance. The proposed method is evaluated with synthetic data of a randomly generated index of refraction value and used to visualize a fuel injection volumetric data.
A Generalized Fluid System Simulation Program to Model Flow Distribution in Fluid Networks
Majumdar, Alok; Bailey, John W.; Schallhorn, Paul; Steadman, Todd
1998-01-01
This paper describes a general purpose computer program for analyzing steady state and transient flow in a complex network. The program is capable of modeling phase changes, compressibility, mixture thermodynamics and external body forces such as gravity and centrifugal. The program's preprocessor allows the user to interactively develop a fluid network simulation consisting of nodes and branches. Mass, energy and specie conservation equations are solved at the nodes; the momentum conservation equations are solved in the branches. The program contains subroutines for computing "real fluid" thermodynamic and thermophysical properties for 33 fluids. The fluids are: helium, methane, neon, nitrogen, carbon monoxide, oxygen, argon, carbon dioxide, fluorine, hydrogen, parahydrogen, water, kerosene (RP-1), isobutane, butane, deuterium, ethane, ethylene, hydrogen sulfide, krypton, propane, xenon, R-11, R-12, R-22, R-32, R-123, R-124, R-125, R-134A, R-152A, nitrogen trifluoride and ammonia. The program also provides the options of using any incompressible fluid with constant density and viscosity or ideal gas. Seventeen different resistance/source options are provided for modeling momentum sources or sinks in the branches. These options include: pipe flow, flow through a restriction, non-circular duct, pipe flow with entrance and/or exit losses, thin sharp orifice, thick orifice, square edge reduction, square edge expansion, rotating annular duct, rotating radial duct, labyrinth seal, parallel plates, common fittings and valves, pump characteristics, pump power, valve with a given loss coefficient, and a Joule-Thompson device. The system of equations describing the fluid network is solved by a hybrid numerical method that is a combination of the Newton-Raphson and successive substitution methods. This paper also illustrates the application and verification of the code by comparison with Hardy Cross method for steady state flow and analytical solution for unsteady flow.
Experimental study on fluid flow in arciform clearance
邵俊鹏; 汤卉; 贾慧娟
2002-01-01
The system damping and dynamic characteristics can be further improved by properly increasing thedamping coefficient ξh. For a special hydraulic damping structure, an arciform damping clearance often used inFCS, a mathematical model has been established for fluid flow using the theory of laminar flow in the clearanceof parallel plates. Analytical calculations are made for fluid flow in the arciform clearance and relational expres-sion is deduced for flow rate along the arciform cleaance height, pressure difference, maximum arciform clear-ance height, the flow rate for the fluid flow in arciform clearance as well, and its simplified formula is obtainedby using the theory of hydrodynamics and the curve - fitting method. This paper consists of two sections: the firstsection focuses on the theoretical analysis by using the simplified mathematical model and the second sectionmainly describes experimental analysis. The simplified formula is corrected with experimental results by consid-erig various boundary conditions of the damping clearance. Experimental results show that this study of arciformdamping clearance is reliable and practical.
A quantitative analysis of cerebrospinal fluid flow in posttraumatic syringomyelia
Tobimatsu, Yoshiko; Nihei, Ryuuichi; Kimura, Tetsuhiko; Suyama, Tetsuo; Tobimatsu, Haruki (National Rehabilitation Center for the Disabled Hospital, Tokorozawa, Saitama (Japan))
1991-08-01
Cerebrospinal fluid (CSF) flow within the spinal canal and syrinx in posttraumatic syringomyelia were studied by cardiac-gated phase images of magnetic resonance imaging in 12 normal volunteers and 8 patients with syringomyelia. The cardiac-gated phase method was simple and useful for detection of CSF flow. Phase modulation was in direct proportion to flow velocity. Phase modulation was not affected by the T1 or T2 relaxation time. In normal volunteers, CSF flows caudally during systole and cranially during diastole. The maximum caudal CSF flow velocity at C2 level was from 0.45 cm/sec to 1.71 cm/sec, average; 1.27 cm/sec. All of symptomatic posttraumatic syringomyelia patients had the flow in the syrinx. (author).
Experimental observation of fluid flow channels in a single fracture
Brown, Stephen; Caprihan, Arvind; Hardy, Robert
1998-03-01
A method for obtaining precise replicas of real fracture surfaces using transparent epoxy resins was developed, allowing detailed study of fluid flow paths within a fracture plane. A natural rock fracture was collected from the field and prepared for study. Silicon rubber molds of the fracture surfaces were used to make a transparent epoxy replica of the original fracture. Clear and dyed water were injected into the fracture pore space allowing examination of the flow field. Digitized optical images were used to observe wetting, saturated flow, and drying of the specimen. Nuclear magnetic resonance imaging was used for quantitative measurements of flow velocity. Both video imaging and nuclear magnetic resonance imaging techniques show distinct and strong channeling of the flow at the submillimeter to several-centimeter scale. Each phenomenon, including wetting, drying, dye transport, and velocity channeling, has its own distinct geometric structure and scale. We find that fluid velocities measured simultaneously at various locations in the fracture plane during steady state flow range over several orders of magnitude, with the maximum velocity a factor of 5 higher than the mean velocity. This suggests that flow channeling in fractured rock can cause the breakthrough velocity of contaminants to far exceed the mean flow.
Moeck, Christian; Radny, Dirk; Borer, Paul; Rothardt, Judith; Auckenthaler, Adrian; Berg, Michael; Schirmer, Mario
2016-11-01
A combined approach of multivariate statistical analysis, namely factor analysis (FA) and hierarchical cluster analysis (HCA), interpretation of geochemical processes, stable water isotope data and organic micropollutants enabling to assess spatial patterns of water types was performed for a study area in Switzerland, where drinking water production is close to different potential input pathways for contamination. To avoid drinking water contamination, artificial groundwater recharge with surface water into an aquifer is used to create a hydraulic barrier between potential intake pathways for contamination and drinking water extraction wells. Inter-aquifer mixing in the subsurface is identified, where a high amount of artificial infiltrated surface water is mixed with a lesser amount of water originating from the regional flow pathway in the vicinity of drinking water extraction wells. The spatial distribution of different water types can be estimated and a conceptual system understanding is developed. Results of the multivariate statistical analysis are comparable with gained information from isotopic data and organic micropollutants analyses. The integrated approach using different kinds of observations can be easily transferred to a variety of hydrological settings to synthesise and evaluate large hydrochemical datasets. The combination of additional data with different information content is conceivable and enabled effective interpretation of hydrological processes. Using the applied approach leads to more sound conceptual system understanding acting as the very basis to develop improved water resources management practices in a sustainable way.
Computational fluid dynamics analysis of a mixed flow pump impeller
ATHARVA
results of CFD analysis, the velocity and pressure in the outlet of the impeller is predicted. ... The numerical simulation can provide quite accurate information on the fluid ... of the computational domain the mass flow rate, the turbulence intensity, and a reference pressure are specified. .... Averaged velocity distribution.
Numerical analysis of complex fluid-flow systems
Holland, R. L.
1980-01-01
Very flexible computer-assisted numerical analysis is used to solve dynamic fluid-flow equations characterizing computer-controlled heat dissipation system developed for Space lab. Losses caused by bends, ties, fittings, valves, and like are easily included, and analysis can solve both steady-state and transient cases. It can also interact with parallel thermal analysis.
Numerical Modeling of Fluid Flow in the Tape Casting Process
Jabbari, Masoud; Hattel, Jesper Henri
2011-01-01
The flow behavior of the fluid in the tape casting process is analyzed. A simple geometry is assumed for running the numerical calculations in ANSYS Fluent and the main parameters are expressed in non-dimensional form. The effect of different values for substrate velocity and pressure force...
Eigenvalues of the time—dependent fluid flow problem I
El-Sayed M. Zayed
1990-01-01
Full Text Available The direct and inverse boundary value problems for the linear unsteady viscous fluid flow through a closed conduit of a circular annular cross-section Ω with arbitrary time-dependent pressure gradient under the third boundary conditions have been investigated.
Flow Curve Determination for Non-Newtonian Fluids.
Tjahjadi, Mahari; Gupta, Santosh K.
1986-01-01
Describes an experimental program to examine flow curve determination for non-Newtonian fluids. Includes apparatus used (a modification of Walawender and Chen's set-up, but using a 50cc buret connected to a glass capillary through a Tygon tube), theoretical information, procedures, and typical results obtained. (JN)
Fluid Flow and Heat Transfer over a Permeable Stretching Cylinder
K Vajravelu
2014-01-01
Full Text Available In this paper, we analyze the effects of thermo-physical properties on the axisymmetric flow of a viscous fluid induced by a stretching cylinder in the presence of internal heat generation/absorption. It is assumed that the cylinder is stretched in the axial direction with a linear velocity and the surface temperature of the cylinder is subjected to vary linearly. Here, the temperature dependent thermo-physical properties namely, the fluid viscosity and the fluid thermal conductivity are respectively assumed to vary as an inverse function of the temperature and a linear function of the temperature. The governing system of partial differential equations is converted into a system of coupled non-linear ordinary differential equations with variable coefficients. The resulting system is solved numerically using a second order finite difference scheme known as the Keller-box method. The governing equations of the problem show that the flow and heat transfer characteristics depend on six parameters, namely the curvature parameter, fluid viscosity parameter, injection/suction parameter, variable thermal conductivity parameter, heat source/sink parameter and the Prandtl number. The numerical values obtained for the velocity, temperature, skin friction, and the Nusselt number are presented through graphs and tables for several sets of values of the pertinent parameters. The results obtained for the flow and heat transfer characteristics reveal many interesting behaviors that warrant further study on the axisymmetric flow phenomena. Comparisons with the available results in the literature are presented as special cases.
Analysis of fluid flow around a beating artificial cilium
Mojca Vilfan
2012-02-01
Full Text Available Biological cilia are found on surfaces of some microorganisms and on surfaces of many eukaryotic cells where they interact with the surrounding fluid. The periodic beating of the cilia is asymmetric, resulting in directed swimming of unicellular organisms or in generation of a fluid flow above a ciliated surface in multicellular ones. Following the biological example, externally driven artificial cilia have recently been successfully implemented as micropumps and mixers. However, biomimetic systems are useful not only in microfluidic applications, but can also serve as model systems for the study of fundamental hydrodynamic phenomena in biological samples. To gain insight into the basic principles governing propulsion and fluid pumping on a micron level, we investigated hydrodynamics around one beating artificial cilium. The cilium was composed of superparamagnetic particles and driven along a tilted cone by a varying external magnetic field. Nonmagnetic tracer particles were used for monitoring the fluid flow generated by the cilium. The average flow velocity in the pumping direction was obtained as a function of different parameters, such as the rotation frequency, the asymmetry of the beat pattern, and the cilium length. We also calculated the velocity field around the beating cilium by using the analytical far-field expansion. The measured average flow velocity and the theoretical prediction show an excellent agreement.
Control of Low Reynolds Number Flows with Fluid Structure Interactions
2014-02-02
public release; distribution is unlimited. 27 the direct numerical simulations of Andro and Jacquin [37] for a plunging NACA 0012 airfoil at Re...34Bifurcating Flows of Plunging Airfoils at High Strouhal Numbers," Journal of Fluid Mechanics, Vol. 708, 2012, pp. 349-376. [37] Andro , J.Y
Reduced order modeling of some fluid flows of industrial interest
Alonso, D; Terragni, F; Velazquez, A; Vega, J M, E-mail: josemanuel.vega@upm.es [E.T.S.I. Aeronauticos, Universidad Politecnica de Madrid, 28040 Madrid (Spain)
2012-06-01
Some basic ideas are presented for the construction of robust, computationally efficient reduced order models amenable to be used in industrial environments, combined with somewhat rough computational fluid dynamics solvers. These ideas result from a critical review of the basic principles of proper orthogonal decomposition-based reduced order modeling of both steady and unsteady fluid flows. In particular, the extent to which some artifacts of the computational fluid dynamics solvers can be ignored is addressed, which opens up the possibility of obtaining quite flexible reduced order models. The methods are illustrated with the steady aerodynamic flow around a horizontal tail plane of a commercial aircraft in transonic conditions, and the unsteady lid-driven cavity problem. In both cases, the approximations are fairly good, thus reducing the computational cost by a significant factor. (review)
Tracing fluid flow in geothermal reservoirs
Rose, P.E.; Adams, M.C. [Univ. of Utah, Salt Lake City, UT (United States)
1997-12-31
A family of fluorescent compounds, the polycyclic aromatic sulfonates, were evaluated for application in intermediate- and high-temperature geothermal reservoirs. Whereas the naphthalene sulfonates were found to be very thermally stable and reasonably detectable, the amino-substituted naphthalene sulfonates were found to be somewhat less thermally stable, but much more detectable. A tracer test was conducted at the Dixie Valley, Nevada, geothermal reservoir using one of the substituted naphthalene sulfonates, amino G, and fluorescein. Four of 9 production wells showed tracer breakthrough during the first 200 days of the test. Reconstructed tracer return curves are presented that correct for the thermal decay of tracer assuming an average reservoir temperature of 227{degrees}C. In order to examine the feasibility of using numerical simulation to model tracer flow, we developed simple, two-dimensional models of the geothermal reservoir using the numerical simulation programs TETRAD and TOUGH2. By fitting model outputs to measured return curves, we show that numerical reservoir simulations can be calibrated with the tracer data. Both models predict the same order of elution, approximate tracer concentrations, and return curve shapes. Using these results, we propose a method for using numerical models to design a tracer test.
Fluid flow and dissipation in intersecting counter-flow pipes
Pekkan, Kerem
2005-11-01
Intersecting pipe junctions are common in industrial and biomedical flows. For the later application, standard surgical connections of vessel lumens results a ``+'' shaped topology through a side-to-side or end-to-side anastomosis. Our earlier experimental/computational studies have compared different geometries quantifying the hydrodynamic power loss through the junction where dominant coherent structures are identified. In this study we have calculated the contribution of these structures to the total energy dissipation and its spatial distribution in the connection. A large set of idealized models are studied in which the basic geometric configuration is parametrically varied (from side-to-side to end-to-side anastomosis) which quantified the strength of the secondary flows and coherent structures as a function of the geometric configuration. Steady-state, 3D, incompressible computations are performed using the commercial CFD code FIDAP with unstructured tetrahedral grids. Selected cases are compared with the in-house code results (in Cartesian and structured grids). Grid verification and experimental validation with flow-vis and PIV are presented. Identifying the dissipation hot-spots will enable a targeted inverse design of the junction by reducing the degree of optimization with a focused parameter space.
Steady State Stokes Flow Interpolation for Fluid Control
Bhatacharya, Haimasree; Nielsen, Michael Bang; Bridson, Robert
2012-01-01
Fluid control methods often require surface velocities interpolated throughout the interior of a shape to use the velocity as a feedback force or as a boundary condition. Prior methods for interpolation in computer graphics — velocity extrapolation in the normal direction and potential flow...... — suffer from a common problem. They fail to capture the rotational components of the velocity field, although extrapolation in the normal direction does consider the tangential component. We address this problem by casting the interpolation as a steady state Stokes flow. This type of flow captures...... the rotational components and is suitable for controlling liquid animations where tangential motion is pronounced, such as in a breaking wave...
HYDROMAGNETIC DIVERGENT CHANNEL FLOW OF A VISCOELASTIC ELECTRICALLY CONDUCTING FLUID
RITA CHOUDHURY
2011-10-01
Full Text Available A theoretical study for the two-dimensional boundary layer flow through a divergent channel of a visco-elastic electrically conducting fluid in presence of transverse magnetic field has been considered. Similarity solutions are obtained by considering a special form of magnetic field. The analytical expressions for velocity and skin friction at the wall have been obtained and numerically worked out for different values of the flow parametersinvolved in the solution. The velocity and the skin friction coefficient have been presented graphically to observe the visco-elastic effects for various values of the flow parameters across the boundary layer.
Review of coaxial flow gas core nuclear rocket fluid mechanics
Weinstein, H.
1976-01-01
Almost all of the fluid mechanics research associated with the coaxial flow gas core reactor ended abruptly with the interruption of NASA's space nuclear program because of policy and budgetary considerations in 1973. An overview of program accomplishments is presented through a review of the experiments conducted and the analyses performed. Areas are indicated where additional research is required for a fuller understanding of cavity flow and of the factors which influence cold and hot flow containment. A bibliography is included with graphic material.
Localized microstructures induced by fluid flow in directional solidification.
Jamgotchian, H; Bergeon, N; Benielli, D; Voge, P; Billia, B; Guérin, R
2001-10-15
The dynamical process of microstructure localization by multiscale interaction between instabilities is uncovered in directional solidification of transparent alloy. As predicted by Chen and Davis, morphological instability of the interface is observed at inward flow-stagnation regions of the cellular convective field. Depending on the driving force of fluid flow, focus-type and honeycomb-type localized patterns form in the initial transient of solidification, that then evolves with time. In the case of solute-driven flow, the analysis of the onset of thermosolutal convection in initial transient of solidification enables a complete understanding of the dynamics and of the localization of morphological instability.
3D couette flow of dusty fluid with transpiration cooling
GOVINDARAJAN A.; RAMAMURTHY V.; SUNDARAMMAL K.
2007-01-01
The couette dusty flow between two horizontal parallel porous flat plates with transverse sinusoidal injection of the dusty fluid at the stationary plate and its corresponding removal by constant suction through the plate in uniform motion was analyzed. Due to this type of injection velocity the dusty flow becomes 3D. Perturbation method is used to obtain the expressions for the velocity and temperature fields of both the fluid and dust. It was found that the velocity profiles of both the fluid and dust in the main flow direction decrease with the increase of the mass concentration of the dust panicles, and those in cross flow direction increase with an increase in the mass concentration of the dust particles up to the middle of the channel and thereafter decrease with increase in mass concentration of the dust particles. The skin friction components Tx and Tz in the main flow and transverse directions respectively increase with an increase in the mass concentration of the dust particles (or) injection parameter. The heat transfer coefficient decreases with the increase of the injection parameter and increases with the increase in the mass concentration of the dust particles.
Squeeze flow of a Carreau fluid during sphere impact
Uddin, J.
2012-07-19
We present results from a combined numerical and experimental investigation into the squeeze flow induced when a solid sphere impacts onto a thin, ultra-viscous film of non-Newtonian fluid. We examine both the sphere motion through the liquid as well as the fluid flow field in the region directly beneath the sphere during approach to a solid plate. In the experiments we use silicone oil as the model fluid, which is well-described by the Carreau model. We use high-speed imaging and particle tracking to achieve flow visualisation within the film itself and derive the corresponding velocity fields. We show that the radial velocity either diverges as the gap between the sphere and the wall diminishes (Z tip → 0) or that it reaches a maximum value and then decays rapidly to zero as the sphere comes to rest at a non-zero distance (Z tip = Z min ) away from the wall. The horizontal shear rate is calculated and is responsible for significant viscosity reduction during the approach of the sphere. Our model of this flow, based on lubrication theory, is solved numerically and compared to experimental trials. We show that our model is able to correctly describe the physical features of the flow observed in the experiments.
无
2001-01-01
The continuum approach in fluid flow modeling is generally applied to porous geological media,but has limitel applicability to fractured rocks. With the presence of a discrete fracture network relatively sparsely distributed in the matrix, it may be difficult or erroneous to use a porous medium fluid flow model with continuum assumptions to describe the fluid flow in fractured rocks at small or even large field scales. A discrete fracture fluid flow approach incorporating a stochastic fracture network with numerical fluid flow simulations could have the capability of capturing fluid flow behaviors such as inhomogeneity and anisotropy while reflecting the changes of hydraulic features at different scales.Moreover, this approach can be implemented to estimate the size of the representative elementary volume (REV) in order to find out the scales at which a porous medium flow model could be applied, and then to determine the hydraulic conductivity tensor for fractured rocks. The following topics are focused on in this study: (a) conceptual discrete fracture fluid flow modeling incorporating a stochastic fracture network with numerical flow simulations; (b) estimation of REVand hydraulic conductivity tensor for fractured rocks utilizing a stochastic fracture network with numerical fluid flow simulations; (c) investigation of the effect of fracture orientation and density on the hydraulic conductivity and REV by implementing a stochastic fracture network with numerical fluid flow simulations, and (d) fluid flow conceptual models accounting for major and minor fractures in the 2-D or 3-D flow fields incorporating a stochastic fracture network with numerical fluid flow simulations.``
Neutron radigoraphy of fluid flow for geothermal energy research
Bingham, Philip R [ORNL; Polsky, Yarom [ORNL; Anovitz, Lawrence {Larry} M [ORNL; Carmichael, Justin R [ORNL; Bilheux, Hassina Z [ORNL; Hussey, Dan [NIST Center for Neutron Research (NCRN), Gaithersburg, MD; Jacobson, David [National Institute of Standards and Technology (NIST)
2015-01-01
Enhanced geothermal systems seek to expand the potential for geothermal energy by engineering heat exchange systems within the earth. A neutron radiography imaging method has been developed for the study of fluid flow through rock under environmental conditions found in enhanced geothermal energy systems. For this method, a pressure vessel suitable for neutron radiography was designed and fabricated, modifications to imaging instrument setups were tested, multiple contrast agents were tested, and algorithms developed for tracking of flow. The method has shown success for tracking of single phase flow through a manufactured crack in a 3.81 cm (1.5 inch) diameter core within a pressure vessel capable of confinement up to 69 MPa (10,000 psi) using a particle tracking approach with bubbles of fluorocarbon-based fluid as the “particles” and imaging with 10 ms exposures.
Mathematical Modelling of Fluid Flow in Cone and Cavitation Formation
Milada KOZUBKOVÁ
2011-06-01
Full Text Available Problem of cavitation is the undesirable phenomena occuring in the fluid flow in many hydraulic application (pumps, turbines, valves, etc.. Therefore this is in the focus of interest using experimental and mathematical methods. Based on cavitation modelling in Laval nozzle results and experience [1], [2], [4], following problem described as the water flow at the outlet from turbine blade wheel was solved. Primarily the problem is simplified into modelling of water flow in cone. Profiles of axial, radial and tangential velocity are defined on inlet zone. The value of pressure is defined on the outlet. Boundary conditions were defined by main investigator of the grant project – Energy Institute, Victor Kaplan’s Department of Fluid Engineering, Faculty of Mechanical Engineering, Brno University of Technology. The value of air volume was insignificant. Cavitation was solved by Singhal model of cavitation.
Hydrodynamic Fluctuations in Laminar Fluid Flow. II. Fluctuating Squire Equation
Ortiz de Zárate, José M.; Sengers, Jan V.
2013-02-01
We use fluctuating hydrodynamics to evaluate the enhancement of thermally excited fluctuations in laminar fluid flow using plane Couette flow as a representative example. In a previous publication (J. Stat. Phys. 144:774, 2011) we derived the energy amplification arising from thermally excited wall-normal fluctuations by solving a fluctuating Orr-Sommerfeld equation. In the present paper we derive the energy amplification arising from wall-normal vorticity fluctuation by solving a fluctuating Squire equation. The thermally excited wall-normal vorticity fluctuations turn out to yield the dominant contribution to the energy amplification. In addition, we show that thermally excited streaks, even in the absence of any externally imposed perturbations, are present in laminar fluid flow.
An improved model for reduced-order physiological fluid flows
San, Omer; 10.1142/S0219519411004666
2012-01-01
An improved one-dimensional mathematical model based on Pulsed Flow Equations (PFE) is derived by integrating the axial component of the momentum equation over the transient Womersley velocity profile, providing a dynamic momentum equation whose coefficients are smoothly varying functions of the spatial variable. The resulting momentum equation along with the continuity equation and pressure-area relation form our reduced-order model for physiological fluid flows in one dimension, and are aimed at providing accurate and fast-to-compute global models for physiological systems represented as networks of quasi one-dimensional fluid flows. The consequent nonlinear coupled system of equations is solved by the Lax-Wendroff scheme and is then applied to an open model arterial network of the human vascular system containing the largest fifty-five arteries. The proposed model with functional coefficients is compared with current classical one-dimensional theories which assume steady state Hagen-Poiseuille velocity pro...
FLUENT/BFC - A general purpose fluid flow modeling program for all flow speeds
Dvinsky, Arkady S.
FLUENT/BFC is a fluid flow modeling program for a variety of applications. Current capabilities of the program include laminar and turbulent flows, subsonic and supersonic viscous flows, incompressible flows, time-dependent and stationary flows, isothermal flows and flows with heat transfer, Newtonian and power-law fluids. The modeling equations in the program have been written in coordinate system invariant form to accommodate the use of boundary-conforming, generally nonorthogonal coordinate systems. The boundary-conforming coordinate system can be generated using both an internal grid generator, which is an integral part of the code, and external application-specific grid generators. The internal grid generator is based on a solution of a system of elliptic partial differential equations and can produce grids for a wide variety of two- and three-dimensional geometries.
Flow in the well: computational fluid dynamics is essential in flow chamber construction.
Vogel, Markus; Franke, Jörg; Frank, Wolfram; Schroten, Horst
2007-09-01
A perfusion system was developed to generate well defined flow conditions within a well of a standard multidish. Human vein endothelial cells were cultured under flow conditions and cell response was analyzed by microscopy. Endothelial cells became elongated and spindle shaped. As demonstrated by computational fluid dynamics (CFD), cells were cultured under well defined but time varying shear stress conditions. A damper system was introduced which reduced pulsatile flow when using volumetric pumps. The flow and the wall shear stress distribution were analyzed by CFD for the steady and unsteady flow field. Usage of the volumetric pump caused variations of the wall shear stresses despite the controlled fluid environment and introduction of a damper system. Therefore the use of CFD analysis and experimental validation is critical in developing flow chambers and studying cell response to shear stress. The system presented gives an effortless flow chamber setup within a 6-well standard multidish.
Computation of Internal Fluid Flows in Channels Using the CFD Software Tool FlowVision
Kochevsky, A N
2004-01-01
The article describes the CFD software tool FlowVision (OOO "Tesis", Moscow). The model equations used for this research are the set of Reynolds and continuity equations and equations of the standard k - e turbulence model. The aim of the paper was testing of FlowVision by comparing the computational results for a number of simple internal channel fluid flows with known experimental data. The test cases are non-swirling and swirling flows in pipes and diffusers, flows in stationary and rotating bends. Satisfactory correspondence of results was obtained both for flow patterns and respective quantitative values.
Crystal growth in fluid flow: Nonlinear response effects
Peng, H. L.; Herlach, D. M.; Voigtmann, Th.
2017-08-01
We investigate crystal-growth kinetics in the presence of strong shear flow in the liquid, using molecular-dynamics simulations of a binary-alloy model. Close to the equilibrium melting point, shear flow always suppresses the growth of the crystal-liquid interface. For lower temperatures, we find that the growth velocity of the crystal depends nonmonotonically on the shear rate. Slow enough flow enhances the crystal growth, due to an increased particle mobility in the liquid. Stronger flow causes a growth regime that is nearly temperature-independent, in striking contrast to what one expects from the thermodynamic and equilibrium kinetic properties of the system, which both depend strongly on temperature. We rationalize these effects of flow on crystal growth as resulting from the nonlinear response of the fluid to strong shearing forces.
Development of a Laminar Flow Bioreactor by Computational Fluid Dynamics
Meir Israelowitz
2012-01-01
Full Text Available The purpose of this study is to improve the design of a bioreactor for growing bone and other three-dimensional tissues using a computational fluid dynamics (CFD software to simulate flow through a porous scaffold, and to recommend design changes based on the results. Basic requirements for CFD modeling were that the flow in the reactor should be laminar and any flow stagnation should be avoided in order to support cellular growth within the scaffold. We simulated three different designs with different permeability values of the scaffold and tissue. Model simulation addressed flow patterns in combination with pressure distribution within the bioreactor. Pressure build-up and turbulent flow within the reactor was solved by introduction of an integrated bypass system for pressure release. The use of CFD afforded direct feedback to optimize the bioreactor design.
Cerroni, D.; Fancellu, L.; Manservisi, S.; Menghini, F.
2016-06-01
In this work we propose to study the behavior of a solid elastic object that interacts with a multiphase flow. Fluid structure interaction and multiphase problems are of great interest in engineering and science because of many potential applications. The study of this interaction by coupling a fluid structure interaction (FSI) solver with a multiphase problem could open a large range of possibilities in the investigation of realistic problems. We use a FSI solver based on a monolithic approach, while the two-phase interface advection and reconstruction is computed in the framework of a Volume of Fluid method which is one of the more popular algorithms for two-phase flow problems. The coupling between the FSI and VOF algorithm is efficiently handled with the use of MEDMEM libraries implemented in the computational platform Salome. The numerical results of a dam break problem over a deformable solid are reported in order to show the robustness and stability of this numerical approach.
Seafloor Geomorphology as a Possible Indicator to Fluid Flow.
Greene, H. G.; Paull, C. K.
2002-12-01
Multibeam bathymetric data collected by MBARI and the USGS show numerous features marking the seafloor along parts of the California continental margin that suggest they may have been generated by offshore groundwater discharge or would be logical sites for focused fluid venting. These features include pockmarks, carbonate build-ups, steep slide-scars, and depression-studded rills. In addition, the heads of submarine canyons located near the Outer Santa Cruz Basin (northwest of Santa Cruz) and the Santa Maria Basin (near Point Conception), exhibit collapsed features that could result from the flow and possible venting of gas-charged fluids that escaped from a hydrocarbon reservoir. These areas are all associated with either major hydrocarbon reservoirs or onshore groundwater basins and aquifers that may crop out on the seafloor. ROV observations using MBARI's Ventana and Tiburon vehicles were conducted in five areas (Ascension slope northwest of Santa Cruz, Monterey Bay, the Point Lobos pockmark field, northern Santa Barbara Channel and San Pedro-Long Beach slope) where these features occur. While little evidence of active fluid flow was found, some methane-derived carbonates consistent with past flow were discovered. Although some of the morphologic features suggestive of a fluid-induced origin lie on the continental shelf and may have formed during a low-stand of sea level, many features are located on the continental slope and most likely formed in the marine environment.
Numerical modelling of structural controls on fluid flow and mineralization
Yanhua Zhang
2011-07-01
Full Text Available This paper presents the results of a set of numerical models focussing on structural controls on hydrothermal mineralization. We first give an overview of natural phenomena of structurally-controlled ore formation and the background theory and mechanisms for such controls. We then provide the results of a group of simple 2D numerical models validated through comparison with Cu-vein structure observed near the Shilu Copper deposit (Yangchun, Guangdong Province, China and finally a case study of 3D numerical modelling applied to the Hodgkinson Province in North Queensland (Australia. Two modelling approaches, discrete deformation modelling and continuum coupled deformation and fluid flow modelling, are involved. The 2D model-derived patterns are remarkably consistent with the Cu-vein structure from the Shilu Copper deposit, and show that both modelling approaches can realistically simulate the mechanical behaviours of shear and dilatant fractures. The continuum coupled deformation and fluid flow model indicates that pattern of the Cu-veins near the Shilu deposit is the result of shear strain localization, development of dilation and fluid focussing into the dilatant fracture segments. The 3D case-study models (with deformation and fluid flow coupling on the Hodgkinson Province generated a number of potential gold mineralization targets.
Deformation and Fluid Flow in the Etendeka Plateau, NW Namibia
Salomon, Eric; Koehn, Daniel; Passchier, Cees; Davis, Jennifer; Salvona, Aron; Chung, Peter
2014-05-01
We studied deformation bands in sandstone and breccia veins in overlying basalts of the Etendeka Plateau, NW Namibia, regarding their development and history of fluid flow within. The studied deformation bands can be divided into disaggregation bands and cataclastic bands. The former appear to develop in unsorted sandstone, whereas the latter form in well sorted sandstone. We estimated the porosity of the bands and host rock in thin sections using a simple image analysis software (ImageJ). Results show, that no or only a minor decrease in porosity occur in disaggregation bands, while the porosity in cataclastic bands is decreased by up to 82 % with respect to the host rock. These observations are in agreement with results of existing studies (e.g. Fossen et al., 2007). Hence the cataclastic bands form a seal to fluid flow in the host rock, yet it is observed in outcrops that deformation bands can develop into open fractures which in turn increase the permeability of the rock. Breccia veins in the overlying basalts show intense fracturing where the basalt is locally fractured into elongated chips. Mineral precipitation in these breccia veins indicates a hydrothermal origin of the fluids since the precipitates consist of extremely fine-grained quartz aggregates. Secondary mineralization with large crystals indicates that a long-lived fluid circulation through tubular networks was active at a later stage, which eventually sealed the veins completely. We propose that the Etendeka basalts on top of the sandstone formation produced a localized deformation along deformation bands and heated up fluid below the lavas. At a later stage fluid pressures were either high enough to break through the basalt or fracturing due to ongoing extension produced fluid pathways. References Fossen, H., Schultz, R., Shipton, Z. and Mair, K. (2007). Deformation bands in sandstone: a review. J. Geol. Soc., 164, 755-769.
Highly viscous fluid flow in a spinning and nutating cylinder
Herbert, T.
1985-02-01
Spin-stabilized projectiles with liquid payloads can experience a severe flight instability characterized by a rapid yaw angle growth and a simultaneous loss in spin rate. Laboratory experiments and field tests have shown that this instability originates from the internal fluid motion in the range of high viscosity. Evaluation of the experimental data and analysis of the equations for the fluid motion in a spinning and nutating cylinder suggest a theoretical approach in three major steps: (1) analysis of the steady viscous flow in an infinitely long cylinder, (2) hydrodynamic stability analysis of this basic flow, and (3) analysis of the end effects. The basic flow has been found in analytical form. At low Reynolds number, this flow agrees well with computational results for the center section of a cylinder of aspect ratio 4.3. The despin moment caused by this flow largely agrees with experimental data for a wide range of Reynolds numbers. Current work aims at the stability of this flow.
Laminar flow of micropolar fluid in rectangular microchannels
Shangjun Ye; Keqin Zhu; Wen Wang
2006-01-01
Compared with the classic flow on macroscale, flows in microchannels have some new phenomena such as the friction increase and the flow rate reduction. Papautsky and co-workers explained these phenomena by using a micropolar fluid model where the effects of micro-rotation of fluid molecules were taken into account. But both the curl of velocity vector and the curl of micro-rotation gyration vector were given incorrectly in the Cartesian coordinates and then the micro-rotation gyration vector had only one component in the (z)-direction. Besides, the gradient term of the divergence of micro-rotation gyration vector was missed improperly in the angular moment equation. In this paper. the governing equations for laminar flows of micropolar fluid in rectangular microchannels are reconstructed. The numerical results of velocity profiles and micro-rotation gyrations are obtained by a procedure based on the Chebyshev collocation method. The micropolar effects on velocity and micro-rotation gyration are discussed in detail.
A solution algorithm for fluid-particle flows across all flow regimes
Kong, Bo; Fox, Rodney O.
2017-09-01
Many fluid-particle flows occurring in nature and in technological applications exhibit large variations in the local particle volume fraction. For example, in circulating fluidized beds there are regions where the particles are close-packed as well as very dilute regions where particle-particle collisions are rare. Thus, in order to simulate such fluid-particle systems, it is necessary to design a flow solver that can accurately treat all flow regimes occurring simultaneously in the same flow domain. In this work, a solution algorithm is proposed for this purpose. The algorithm is based on splitting the free-transport flux solver dynamically and locally in the flow. In close-packed to moderately dense regions, a hydrodynamic solver is employed, while in dilute to very dilute regions a kinetic-based finite-volume solver is used in conjunction with quadrature-based moment methods. To illustrate the accuracy and robustness of the proposed solution algorithm, it is implemented in OpenFOAM for particle velocity moments up to second order, and applied to simulate gravity-driven, gas-particle flows exhibiting cluster-induced turbulence. By varying the average particle volume fraction in the flow domain, it is demonstrated that the flow solver can handle seamlessly all flow regimes present in fluid-particle flows.
Madlener, K.
2008-07-01
In the present study gelled fluids are investigated concerning their application as propellants in storable and thrust controllable rocket propulsion systems. The correlations between the non-Newtonian viscosity properties and the flow and spray characteristics are discussed. Based on the proposed viscosity model Herschel-Bulkley-Extended (HBE) the laminar pipe flow is calculated for the investigated propellants. With the introduction of a generalized form of the Reynolds number and the presentation of a possibility to determine the critical values of this number it is possible to calculate the laminar-turbulent transition in a pipe flow. The theoretical results are evaluated with experimental data. The spray characteristics of various gelled fluids are examined using an experimental setup with impinging-jet-injectors. (orig.)
Magneto-polar fluid flow through a porous medium of variable permeability in slip flow regime
Gaur P.K.
2016-05-01
Full Text Available A theoretical study is carried out to obtain an analytical solution of free convective heat transfer for the flow of a polar fluid through a porous medium with variable permeability bounded by a semi-infinite vertical plate in a slip flow regime. A uniform magnetic field acts perpendicular to the porous surface. The free stream velocity follows an exponentially decreasing small perturbation law. Using the approximate method the expressions for the velocity, microrotation, and temperature are obtained. Further, the results of the skin friction coefficient, the couple stress coefficient and the rate of heat transfer at the wall are presented with various values of fluid properties and flow conditions.
Do seismic waves and fluid flow sense the same permeability in fluid-saturated porous rocks?
Rubino, J. G.; Monachesi, L. B.; Guarracino, L.; Müller, T. M.; Holliger, K.
2012-04-01
Wave-induced flow due to the the presence of mesoscopic heterogeneities, that is, heterogeneities that are larger than the pore size but smaller than the prevailing seismic wavelengths, represents an important seismic attenuation mechanism in fluid-saturated porous rocks. In this context, it is known that in the presence of strong permeability fluctuations, there is a discrepancy between the effective flow permeability and the effective seismic permeability, that is, the effective permeability controlling seismic attenuation due to wave-induced fluid flow. While this subject has been analyzed for the case of random 1D media, the corresponding 2D and 3D cases remain unexplored, mainly due to the fact that, as opposed to the 1D case, there is no simple expression for the effective flow permeability. In this work we seek to address this problem through the numerical analysis of 2D rock samples having strong permeability fluctuations. In order to do so, we employ a numerical oscillatory compressibility test to determine attenuation and velocity dispersion due to wave-induced fluid flow in these kinds of media and compare the responses with those obtained by replacing the heterogeneous permeability field by homogeneous fields, with permeability values given by the average permeability as well as the effective flow permeability of the sample. The latter is estimated in a separate upscaling procedure by solving the steady-state flow equation in the rock sample under study. Numerical experiments let us verify that the attenuation levels are less significant and the attenuation peak gets broader in the presence of such strong permeability fluctuations. Moreover, we observe that for very low frequencies the effective seismic permeability is similar to the effective flow permeability, while for very high frequencies it approaches the arithmetic average of the permeability field.
Coupling two-phase fluid flow with two-phase darcy flow in anisotropic porous media
Chen, J.
2014-06-03
This paper reports a numerical study of coupling two-phase fluid flow in a free fluid region with two-phase Darcy flow in a homogeneous and anisotropic porous medium region. The model consists of coupled Cahn-Hilliard and Navier-Stokes equations in the free fluid region and the two-phase Darcy law in the anisotropic porous medium region. A Robin-Robin domain decomposition method is used for the coupled Navier-Stokes and Darcy system with the generalized Beavers-Joseph-Saffman condition on the interface between the free flow and the porous media regions. Obtained results have shown the anisotropic properties effect on the velocity and pressure of the two-phase flow. 2014 Jie Chen et al.
Selected topics on the topology of ideal fluid flows
Peralta-Salas, Daniel
2016-08-01
This is a survey of certain geometric aspects of inviscid and incompressible fluid flows, which are described by the solutions to the Euler equations. We will review Arnold’s theorem on the topological structure of stationary fluids in compact manifolds, and Moffatt’s theorem on the topological interpretation of helicity in terms of knot invariants. The recent realization theorem by Enciso and Peralta-Salas of vortex lines of arbitrarily complicated topology for stationary solutions to the Euler equations will also be introduced. The aim of this paper is not to provide detailed proofs of all the stated results but to introduce the main ideas and methods behind certain selected topics of the subject known as Topological Fluid Mechanics. This is the set of lecture notes, the author gave at the XXIV International Fall Workshop on Geometry and Physics held in Zaragoza (Spain) during September 2015.
Characteristics of Electrorheological Fluid Flow in Journal Bearings
张准; 朱克勤
2002-01-01
Under the influence of an applied electric field, the variation of apparent viscosity of electrorheological (ER) fluid flow causes ER effects. According to the Bingham model, which is widely used for describing the rheological properties of ER fluids, this variation should be very weak at high shear rates. To clarify the ER effects in ER journal bearings at high shear rate, a numerical study is presented. It is found that under the influence of the applied electric field, ER effects in ER journal bearings can be affected by not only the apparent viscosity of ER fluids but also the movement of yield surface in the clearance of ER journal bearing. In the case of low shear rate, both are effective on the lubricant film pressure of ER journal bearings. In the case of high shear rates, the main factor is the extension of non-yield region in the bearing clearance.
Vortex generated fluid flows in multiply connected domains
Zemlyanova, Anna; Handley, Demond
2016-01-01
A fluid flow in a multiply connected domain generated by an arbitrary number of point vortices is considered. A stream function for this flow is constructed as a limit of a certain functional sequence using the method of images. The convergence of this sequence is discussed, and the speed of convergence is determined explicitly. The presented formulas allow for the easy computation of the values of the stream function with arbitrary precision in the case of well-separated cylinders. The considered problem is important for applications such as eddy flows in the oceans. Moreover, since finding the stream function of the flow is essentially identical to finding the modified Green's function for Laplace's equation, the presented method can be applied to a more general class of applied problems which involve solving the Dirichlet problem for Laplace's equation.
Gérard J. Poitras; L.-Emmanuel Brizzi; Yves Gagnon
2001-01-01
The results of different numerical algorithms for the computation of unsteady fluid flows are used to visualize different variables of the flow. In particular, the instantaneous vorticity, velocity and pressure fields, along with streamline plots, are presented as a function of time inside a visualization window of the computational domain.The different forms of visualization are used to analyze the flow inside a two-dimensional channel incorporating an obstacle, which can represent several interesting flows such as the flow over electronic components, heat transfer devices and buildings.
Least Squares Shadowing for Sensitivity Analysis of Turbulent Fluid Flows
Blonigan, Patrick; Wang, Qiqi
2014-01-01
Computational methods for sensitivity analysis are invaluable tools for aerodynamics research and engineering design. However, traditional sensitivity analysis methods break down when applied to long-time averaged quantities in turbulent fluid flow fields, specifically those obtained using high-fidelity turbulence simulations. This is because of a number of dynamical properties of turbulent and chaotic fluid flows, most importantly high sensitivity of the initial value problem, popularly known as the "butterfly effect". The recently developed least squares shadowing (LSS) method avoids the issues encountered by traditional sensitivity analysis methods by approximating the "shadow trajectory" in phase space, avoiding the high sensitivity of the initial value problem. The following paper discusses how the least squares problem associated with LSS is solved. Two methods are presented and are demonstrated on a simulation of homogeneous isotropic turbulence and the Kuramoto-Sivashinsky (KS) equation, a 4th order c...
Buoy Relay Method for Instantaneous Fluid Flow with Free Surface
无
2000-01-01
Several methods have been used to approximate free surface boundaries in finite-difference numerical simulations. Each of these methods has its advantages and disadvantages. This paper presents a new technique for the numerical solution of transient incompressible free surface fluid flows. This powerful method, which is based on the concepts of "Buoy positioning" and "Buoy relaying", successfully represents the free surface using a Lagrangian method on a Eulerian grid by directly solving the free surface evolution equation. The Eulerian finite-difference forms of the full Navier-Stokes equations are solved by the Successive over Relaxation (SOR) method with a set of buoys to keep track of the free surface. The capabilities of the analysis procedure are demonstrated through viscous free surface fluid flow examples. The method is simpler and more efficient than other methods especially in treating complicated free boundary configurations.
Laminar boundary-layer flow of non-Newtonian fluid
Lin, F. N.; Chern, S. Y.
1979-01-01
A solution for the two-dimensional and axisymmetric laminar boundary-layer momentum equation of power-law non-Newtonian fluid is presented. The analysis makes use of the Merk-Chao series solution method originally devised for the flow of Newtonian fluid. The universal functions for the leading term in the series are tabulated for n from 0.2 to 2. Equations governing the universal functions associated with the second and the third terms are provided. The solution together with either Lighthill's formula or Chao's formula constitutes a simple yet general procedure for the calculation of wall shear and surface heat transfer rate. The theory was applied to flows over a circular cylinder and a sphere and the results compared with published data.
Measuring fluid flow and heat output in seafloor hydrothermal environments
Germanovich, Leonid N.; Hurt, Robert S.; Smith, Joshua E.; Genc, Gence; Lowell, Robert P.
2015-12-01
We review techniques for measuring fluid flow and advective heat output from seafloor hydrothermal systems and describe new anemometer and turbine flowmeter devices we have designed, built, calibrated, and tested. These devices allow measuring fluid velocity at high- and low-temperature focused and diffuse discharge sites at oceanic spreading centers. The devices perform at ocean floor depths and black smoker temperatures and can be used to measure flow rates ranging over 2 orders of magnitude. Flow velocity is determined from the rotation rate of the rotor blades or paddle assembly. These devices have an open bearing design that eliminates clogging by particles or chemical precipitates as the fluid passes by the rotors. The devices are compact and lightweight enough for deployment from either an occupied or remotely operated submersible. The measured flow rates can be used in conjunction with vent temperature or geochemical measurements to obtain heat outputs or geochemical fluxes from both vent chimneys and diffuse flow regions. The devices have been tested on 30 Alvin dives on the Juan de Fuca Ridge and 3 Jason dives on the East Pacific Rise (EPR). We measured an anomalously low entrainment coefficient (0.064) and report 104 new measurements over a wide range of discharge temperatures (5°-363°C), velocities (2-199 cm/s), and depths (1517-2511 m). These include the first advective heat output measurements at the High Rise vent field and the first direct fluid flow measurement at Middle Valley. Our data suggest that black smoker heat output at the Main Endeavour vent field may have declined since 1994 and that after the 2005-2006 eruption, the high-temperature advective flow at the EPR 9°50'N field may have become more channelized, predominately discharging through the Bio 9 structure. We also report 16 measurements on 10 Alvin dives and 2 Jason dives with flow meters that predate devices described in this work and were used in the process of their development
Optimization of micropillar sequences for fluid flow sculpting
Stoecklein, Daniel; Ganapathysubramanian, Baskar [Department of Mechanical Engineering, Iowa State University, Ames, Iowa 50011 (United States); Wu, Chueh-Yu; Kim, Donghyuk; Di Carlo, Dino [Department of Bioengineering, University of California at Los Angeles, Los Angeles, California 90095 (United States)
2016-01-15
Inertial fluid flow deformation around pillars in a microchannel is a new method for controlling fluid flow. Sequences of pillars have been shown to produce a rich phase space with a wide variety of flow transformations. Previous work has successfully demonstrated manual design of pillar sequences to achieve desired transformations of the flow cross section, with experimental validation. However, such a method is not ideal for seeking out complex sculpted shapes as the search space quickly becomes too large for efficient manual discovery. We explore fast, automated optimization methods to solve this problem. We formulate the inertial flow physics in microchannels with different micropillar configurations as a set of state transition matrix operations. These state transition matrices are constructed from experimentally validated streamtraces for a fixed channel length per pillar. This facilitates modeling the effect of a sequence of micropillars as nested matrix-matrix products, which have very efficient numerical implementations. With this new forward model, arbitrary micropillar sequences can be rapidly simulated with various inlet configurations, allowing optimization routines quick access to a large search space. We integrate this framework with the genetic algorithm and showcase its applicability by designing micropillar sequences for various useful transformations. We computationally discover micropillar sequences for complex transformations that are substantially shorter than manually designed sequences. We also determine sequences for novel transformations that were difficult to manually design. Finally, we experimentally validate these computational designs by fabricating devices and comparing predictions with the results from confocal microscopy.
Optimization of micropillar sequences for fluid flow sculpting
Stoecklein, Daniel; Wu, Chueh-Yu; Kim, Donghyuk; Di Carlo, Dino; Ganapathysubramanian, Baskar
2016-01-01
Inertial fluid flow deformation around pillars in a microchannel is a new method for controlling fluid flow. Sequences of pillars have been shown to produce a rich phase space with a wide variety of flow transformations. Previous work has successfully demonstrated manual design of pillar sequences to achieve desired transformations of the flow cross section, with experimental validation. However, such a method is not ideal for seeking out complex sculpted shapes as the search space quickly becomes too large for efficient manual discovery. We explore fast, automated optimization methods to solve this problem. We formulate the inertial flow physics in microchannels with different micropillar configurations as a set of state transition matrix operations. These state transition matrices are constructed from experimentally validated streamtraces for a fixed channel length per pillar. This facilitates modeling the effect of a sequence of micropillars as nested matrix-matrix products, which have very efficient numerical implementations. With this new forward model, arbitrary micropillar sequences can be rapidly simulated with various inlet configurations, allowing optimization routines quick access to a large search space. We integrate this framework with the genetic algorithm and showcase its applicability by designing micropillar sequences for various useful transformations. We computationally discover micropillar sequences for complex transformations that are substantially shorter than manually designed sequences. We also determine sequences for novel transformations that were difficult to manually design. Finally, we experimentally validate these computational designs by fabricating devices and comparing predictions with the results from confocal microscopy.
Fluid dynamics in airway bifurcations: I. Primary flows.
Martonen, T B; Guan, X; Schreck, R M
2001-04-01
The subject of fluid dynamics within human airways is of great importance for the risk assessment of air pollutants (inhalation toxicology) and the targeted delivery of inhaled pharmacologic drugs (aerosol therapy). As cited herein, experimental investigations of flow patterns have been performed on airway models and casts by a number of investigators. We have simulated flow patterns in human lung bifurcations and compared the results with the experimental data of Schreck (1972). The theoretical analyses were performed using a third-party software package, FIDAP, on the Cray T90 supercomputer. This effort is part of a systematic investigation where the effects of inlet conditions, Reynolds numbers, and dimensions and orientations of airways were addressed. This article focuses on primary flows using convective motion and isovelocity contour formats to describe fluid dynamics; subsequent articles in this issue consider secondary currents (Part II) and localized conditions (Part III). The agreement between calculated and measured results, for laminar flows with either parabolic or blunt inlet conditions to the bifurcations, was very good. To our knowledge, this work is the first to present such detailed comparisons of theoretical and experimental flow patterns in airway bifurcations. The agreement suggests that the methodologies can be employed to study factors affecting airflow patterns and particle behavior in human lungs.
Yield Hardening of Electrorheological Fluids in Channel Flow
Helal, Ahmed; Qian, Bian; McKinley, Gareth H.; Hosoi, A. E.
2016-06-01
Electrorheological fluids offer potential for developing rapidly actuated hydraulic devices where shear forces or pressure-driven flow are present. In this study, the Bingham yield stress of electrorheological fluids with different particle volume fractions is investigated experimentally in wall-driven and pressure-driven flow modes using measurements in a parallel-plate rheometer and a microfluidic channel, respectively. A modified Krieger-Dougherty model can be used to describe the effects of the particle volume fraction on the yield stress and is in good agreement with the viscometric data. However, significant yield hardening in pressure-driven channel flow is observed and attributed to an increase and eventual saturation of the particle volume fraction in the channel. A phenomenological physical model linking the densification and consequent microstructure to the ratio of the particle aggregation time scale compared to the convective time scale is presented and used to predict the enhancement in yield stress in channel flow, enabling us to reconcile discrepancies in the literature between wall-driven and pressure-driven flows.
Lagrangian analysis of fluid transport in empirical vortex ring flows
Shadden, Shawn C.; Dabiri, John O.; Marsden, Jerrold E.
2006-01-01
In this paper we apply dynamical systems analyses and computational tools to fluid transport in empirically measured vortex ring flows. Measurements of quasisteadily propagating vortex rings generated by a mechanical piston-cylinder apparatus reveal lobe dynamics during entrainment and detrainment that are consistent with previous theoretical and numerical studies. In addition, the vortex ring wake of a free-swimming Aurelia aurita jellyfish is measured and analyzed in the framework of dynami...
Partitioned fluid-solid coupling for cardiovascular blood flow: left-ventricular fluid mechanics.
Krittian, Sebastian; Janoske, Uwe; Oertel, Herbert; Böhlke, Thomas
2010-04-01
We present a 3D code-coupling approach which has been specialized towards cardiovascular blood flow. For the first time, the prescribed geometry movement of the cardiovascular flow model KaHMo (Karlsruhe Heart Model) has been replaced by a myocardial composite model. Deformation is driven by fluid forces and myocardial response, i.e., both its contractile and constitutive behavior. Whereas the arbitrary Lagrangian-Eulerian formulation (ALE) of the Navier-Stokes equations is discretized by finite volumes (FVM), the solid mechanical finite elasticity equations are discretized by a finite element (FEM) approach. Taking advantage of specialized numerical solution strategies for non-matching fluid and solid domain meshes, an iterative data-exchange guarantees the interface equilibrium of the underlying governing equations. The focus of this work is on left-ventricular fluid-structure interaction based on patient-specific magnetic resonance imaging datasets. Multi-physical phenomena are described by temporal visualization and characteristic FSI numbers. The results gained show flow patterns that are in good agreement with previous observations. A deeper understanding of cavity deformation, blood flow, and their vital interaction can help to improve surgical treatment and clinical therapy planning.
Oscillatory fluid flow influences primary cilia and microtubule mechanics.
Espinha, Lina C; Hoey, David A; Fernandes, Paulo R; Rodrigues, Hélder C; Jacobs, Christopher R
2014-07-01
Many tissues are sensitive to mechanical stimuli; however, the mechanotransduction mechanism used by cells remains unknown in many cases. The primary cilium is a solitary, immotile microtubule-based extension present on nearly every mammalian cell which extends from the basal body. The cilium is a mechanosensitive organelle and has been shown to transduce fluid flow-induced shear stress in tissues, such as the kidney and bone. The majority of microtubules assemble from the mother centriole (basal body), contributing significantly to the anchoring of the primary cilium. Several studies have attempted to quantify the number of microtubules emanating from the basal body and the results vary depending on the cell type. It has also been shown that cellular response to shear stress depends on microtubular integrity. This study hypothesizes that changing the microtubule attachment of primary cilia in response to a mechanical stimulus could change primary cilia mechanics and, possibly, mechanosensitivity. Oscillatory fluid flow was applied to two different cell types and the microtubule attachment to the ciliary base was quantified. For the first time, an increase in microtubules around primary cilia both with time and shear rate in response to oscillatory fluid flow stimulation was demonstrated. Moreover, it is presented that the primary cilium is required for this loading-induced cellular response. This study has demonstrated a new role for the cilium in regulating alterations in the cytoplasmic microtubule network in response to mechanical stimulation, and therefore provides a new insight into how cilia may regulate its mechanics and thus the cells mechanosensitivity.
Interfacial instabilities in a stratified flow of two superposed fluids
Schaflinger, Uwe
1994-06-01
Here we shall present a linear stability analysis of a laminar, stratified flow of two superposed fluids which are a clear liquid and a suspension of solid particles. The investigation is based upon the assumption that the concentration remains constant within the suspension layer. Even for moderate flow-rates the base-state results for a shear induced resuspension flow justify the latter assumption. The numerical solutions display the existence of two different branches that contribute to convective instability: long and short waves which coexist in a certain range of parameters. Also, a range exists where the flow is absolutely unstable. That means a convectively unstable resuspension flow can be only observed for Reynolds numbers larger than a lower, critical Reynolds number but still smaller than a second critical Reynolds number. For flow rates which give rise to a Reynolds number larger than the second critical Reynolds number, the flow is absolutely unstable. In some cases, however, there exists a third bound beyond that the flow is convectively unstable again. Experiments show the same phenomena: for small flow-rates short waves were usually observed but occasionally also the coexistence of short and long waves. These findings are qualitatively in good agreement with the linear stability analysis. Larger flow-rates in the range of the second critical Reynolds number yield strong interfacial waves with wave breaking and detached particles. In this range, the measured flow-parameters, like the resuspension height and the pressure drop are far beyond the theoretical results. Evidently, a further increase of the Reynolds number indicates the transition to a less wavy interface. Finally, the linear stability analysis also predicts interfacial waves in the case of relatively small suspension heights. These results are in accordance with measurements for ripple-type instabilities as they occur under laminar and viscous conditions for a mono-layer of particles.
Topographic instability of flow in a rotating fluid
K. I. Patarashvili
2006-01-01
Full Text Available Here are presented the results of experimental and theoretical studies on a stability of zonal geostrophic flows in the rotating layer of the shallow water. In the experiments, a special apparatus by Abastumani Astrophysical Observatory Georgian Academy of Science was used. This apparatus represents a paraboloid of rotation, which can be set in a regulable rotation around the vertical axis. Maximal diameter of the paraboloid is 1.2 m, radius of curvature in the pole is 0.698 m. In the paraboloid, water spreads on walls as a layer uniform on height under the period of rotation 1.677 s. Against a background of the rotating fluid, the zonal flows are formed by the source-sink system. It consists of two concentric circular perforations on the paraboloid bottom (width is 0.3 cm, radiuses are 8.4 and 57.3 cm, respectively; water can be pumped through them with various velocities and in all directions. It has been established that under constant vertical depth of the rotating fluid the zonal flows are stable. There are given the measurements of the radial profiles for the water level and velocity in the stationary regime. It has been found that zonal flows may lose stability under the presence of the radial gradient of full depth formed by a change of angular velocity of paraboloid rotation. An instability origin results in the loss of flow axial symmetry and in the appearance of self-excited oscillations in the zonal flow. At the given angular velocity of rotation, instability is observed only in the definite range of intensities of the source-sink system. The theoretical estimations are performed in the framework of the equations of the shallow water theory, including the terms describing the bottom friction. It has been shown that the instability of zonal flows found experimentally has a topographical nature and is related with non-monotone dependence of the potential vorticity on radius.
Traveling hairpin-shaped fluid vortices in plane Couette flow.
Deguchi, K; Nagata, M
2010-11-01
Traveling-wave solutions are discovered in plane Couette flow. They are obtained when the so-called steady hairpin vortex state found recently by Gibson [J. Fluid Mech. 638, 243 (2009)] and Itano and Generalis [Phys. Rev. Lett. 102, 114501 (2009)] is continued to sliding Couette flow geometry between two concentric cylinders by using the radius ratio as a homotopy parameter. It turns out that in the plane Couette flow geometry two traveling waves having the phase velocities with opposite signs are associated with their appearance from the steady hairpin vortex state, where the amplitude of the phase velocities increases gradually from zero as the Reynolds number is increased. The solutions obviously inherit the streaky structure of the hairpin vortex state, but shape preserving flow patterns propagate in the streamwise direction. Other striking features of the solution are asymmetric mean flow profiles and strong quasistreamwise vortices which occupy the vicinity of only the top or bottom moving boundary, depending on the sign of the phase velocity. Furthermore, we find that the pitchfork bifurcation associated with the appearance of the solution becomes imperfect when the flow is perturbed by a Poiseuille flow component.
Energy amplification in channel flows of viscoelastic fluids
Hoda, Nazish; Jovanovi?, Mihailo R.; Kumar, Satish
Energy amplification in channel flows of Oldroyd-B fluids is studied from an input-output point of view by analysing the ensemble-average energy density associated with the velocity field of the linearized governing equations. The inputs consist of spatially distributed and temporally varying body forces that are harmonic in the streamwise and spanwise directions and stochastic in the wall-normal direction and in time. Such inputs enable the use of powerful tools from linear systems theory that have recently been applied to analyse Newtonian fluid flows. It is found that the energy density increases with a decrease in viscosity ratio (ratio of solvent viscosity to total viscosity) and an increase in Reynolds number and elasticity number. In most of the cases, streamwise-constant perturbations are most amplified and the location of maximum energy density shifts to higher spanwise wavenumbers with an increase in Reynolds number and elasticity number and a decrease in viscosity ratio. For similar parameter values, the maximum in the energy density occurs at a higher spanwise wavenumber for Poiseuille flow, whereas the maximum energy density achieves larger maxima for Couette flow. At low Reynolds numbers, the energy density decreases monotonically when the elasticity number is sufficiently small, but shows a maximum when the elasticity number becomes sufficiently large, suggesting that elasticity can amplify disturbances even when inertial effects are weak.
Human red blood cells deformed under thermal fluid flow.
Foo, Ji-Jinn; Chan, Vincent; Feng, Zhi-Qin; Liu, Kuo-Kang
2006-03-01
The flow-induced mechanical deformation of a human red blood cell (RBC) during thermal transition between room temperature and 42.0 degrees C is interrogated by laser tweezer experiments. Based on the experimental geometry of the deformed RBC, the surface stresses are determined with the aid of computational fluid dynamics simulation. It is found that the RBC is more deformable while heating through 37.0 degrees C to 42.0 degrees C, especially at a higher flow velocity due to a thermal-fluid effect. More importantly, the degree of RBC deformation is irreversible and becomes softer, and finally reaches a plateau (at a uniform flow velocity U > 60 microm s(-1)) after the heat treatment, which is similar to a strain-hardening dominated process. In addition, computational simulated stress is found to be dependent on the progression of thermotropic phase transition. Overall, the current study provides new insights into the highly coupled temperature and hydrodynamic effects on the biomechanical properties of human erythrocyte in a model hydrodynamic flow system.
Molecular dynamics of fluid flow at solid surfaces
Koplik, Joel; Banavar, Jayanth R.; Willemsen, Jorge F.
1989-05-01
Molecular dynamics techniques are used to study the microscopic aspects of several slow viscous flows past a solid wall, where both fluid and wall have a molecular structure. Systems of several thousand molecules are found to exhibit reasonable continuum behavior, albeit with significant thermal fluctuations. In Couette and Poiseuille flow of liquids it is found that the no-slip boundary condition arises naturally as a consequence of molecular roughness, and that the velocity and stress fields agree with the solutions of the Stokes equations. At lower densities slip appears, which can be incorporated into a flow-independent slip-length boundary condition. The trajectories of individual molecules in Poiseuille flow are examined, and it is also found that their average behavior is given by Taylor-Aris hydrodynamic dispersion. An immiscible two-fluid system is simulated by a species-dependent intermolecular interaction. A static meniscus is observed whose contact angle agrees with simple estimates and, when motion occurs, velocity-dependent advancing and receding angles are observed. The local velocity field near a moving contact line shows a breakdown of the no-slip condition and, up to substantial statistical fluctuations, is consistent with earlier predictions of Dussan [AIChE J. 23, 131 (1977)].
Turbulent characteristics of shear-thinning fluids in recirculating flows
Pereira, A.S. [Inst. Superior de Engenharia do Porto (Portugal). Dept. de Engenharia Quimica; Pinho, F.T. [Centro de Estudos de Fenomenos de Transporte, Departamento de Engenharia Mecanica e Gestao Industrial, Faculdade de Engenharia da Universidade do Porto, Rua dos Bragas, 4050-123 Porto (Portugal)
2000-03-01
A miniaturised fibre optic laser-Doppler anemometer was used to carry out a detailed hydrodynamic investigation of the flow downstream of a sudden expansion with 0.1-0.2% by weight shear-thinning aqueous solutions of xanthan gum. Upstream of the sudden expansion the pipe flow was fully-developed and the xanthan gum solutions exhibited drag reduction with corresponding lower radial and tangential normal Reynolds stresses, but higher axial Reynolds stress near the wall and a flatter axial mean velocity profile in comparison with Newtonian flow. The recirculation bubble length was reduced by more than 20% relative to the high Reynolds number Newtonian flow, and this was attributed to the occurrence further upstream of high turbulence for the non-Newtonian solutions, because of advection of turbulence and earlier high turbulence production in the shear layer. Comparisons with the measurements of Escudier and Smith (1999) with similar fluids emphasized the dominating role of inlet turbulence. The present was less anisotropic, and had lower maximum axial Reynolds stresses (by 16%) but higher radial turbulence (20%) than theirs. They reported considerably longer recirculating bubble lengths than we do for similar non-Newtonian fluids and Reynolds numbers. (orig.)
Local mesh refinement for incompressible fluid flow with free surfaces
Terasaka, H.; Kajiwara, H.; Ogura, K. [Tokyo Electric Power Company (Japan)] [and others
1995-09-01
A new local mesh refinement (LMR) technique has been developed and applied to incompressible fluid flows with free surface boundaries. The LMR method embeds patches of fine grid in arbitrary regions of interest. Hence, more accurate solutions can be obtained with a lower number of computational cells. This method is very suitable for the simulation of free surface movements because free surface flow problems generally require a finer computational grid to obtain adequate results. By using this technique, one can place finer grids only near the surfaces, and therefore greatly reduce the total number of cells and computational costs. This paper introduces LMR3D, a three-dimensional incompressible flow analysis code. Numerical examples calculated with the code demonstrate well the advantages of the LMR method.
Convective flow of sisko fluid over a bidirectional stretching sheet
Munir, Asif; Khan, Masood
2014-01-01
The present investigation discusses the flow and heat transfer characteristics of a steady three dimensional Sisko fluid. The flow is induced due to bidirectional stretching sheet. The influence of power-law index and stretching ratio on flow and heat transfer is studied thoroughly. Governing partial differential equations are reduced to coupled ordinary differential equations by suitable similarity variable. The resulting equations are then solved numerically by shooting method using adaptive Runge Kutta algorithm in combination with Broyden's method in the domain . The numerical results for the velocity and temperature fields are graphically presented and effects of the relevant parameters are discussed in detail. Moreover, the skin-friction coefficient and local Nusselt number for different values of the power-law index and stretching ratio are presented through tabulated data. The numerical results are verified with the results obtained by HAM. Additionally, the results are also validated with previously ...
Fluid mechanics relevant to flow through pretreatment of cellulosic biomass.
Archambault-Léger, Véronique; Lynd, Lee R
2014-04-01
The present study investigates fluid mechanical properties of cellulosic feedstocks relevant to flow through (FT) pretreatment for biological conversion of cellulosic biomass. The results inform identifying conditions for which FT pretreatment can be implemented in a practical context. Measurements of pressure drop across packed beds, viscous compaction and water absorption are reported for milled and not milled sugarcane bagasse, switchgrass and poplar, and important factors impacting viscous flow are deduced. Using biomass knife-milled to pass through a 2mm sieve, the observed pressure drop was highest for bagasse, intermediate for switchgrass and lowest for poplar. The highest pressure drop was associated with the presence of more fine particles, greater viscous compaction and the degree of water absorption. Using bagasse without particle size reduction, the instability of the reactor during pretreatment above 140kg/m(3) sets an upper bound on the allowable concentration for continuous stable flow.
Flow behaviour of negatively buoyant jets in immiscible ambient fluid
Geyer, A. [CIMNE International Center for Numerical Models in Engineering, Barcelona (Spain); CSIC, Institute of Earth Sciences Jaume Almera, Barcelona (Spain); Phillips, J.C. [University of Bristol, Department of Earth Sciences, Bristol (United Kingdom); Mier-Torrecilla, M.; Idelsohn, S.R.; Onate, E. [CIMNE International Center for Numerical Models in Engineering, Barcelona (Spain)
2012-01-15
In this paper we investigate experimentally the injection of a negatively buoyant jet into a homogenous immiscible ambient fluid. Experiments are carried out by injecting a jet of dyed fresh water through a nozzle in the base of a cylindrical tank containing rapeseed oil. The fountain inlet flow rate and nozzle diameter were varied to cover a wide range of Richardson Ri (8 x 10{sup -4}
Estimation of flow velocity for a debris flow via the two-phase fluid model
S. Guo
2014-06-01
Full Text Available The two-phase fluid model is applied in this study to calculate the steady velocity of a debris flow along a channel bed. By using the momentum equations of the solid and liquid phases in the debris flow together with an empirical formula to describe the interaction between two phases, the steady velocities of the solid and liquid phases are obtained theoretically. The comparison of those velocities obtained by the proposed method with the observed velocities of two real-world debris flows shows that the proposed method can estimate accurately the velocity for a debris flow.
UNIFORMLY ACCURATE KFVS METHODS FOR MULTI-COMPONENT FLOW CALCULATIONS%一致高精度KFVS方法用于多分量流的计算
汤华中; 邬华谟
2001-01-01
This paper is to study extension of high resolution kinetic flux-vector splitting (KFVS) methods.In this new method,two Maxwellians are first introduced to recover the Euler equations with an additional conservative equation.Next,based on the well-known connection between the Euler equations and Boltzmann equations,a class of high resolution KFVS methods are presented to solve numerically multicomponent flows.Our method does not solve any Riemann problems,and add any nonconservative corrections.The numerical results are also presented to show the accuracy and robustness of our methods.These include one-dimensional shock tube problem,and two-dimensional interface motion in compressible flows.The computed solutions are oscillation-free near material fronts,and produce correct shock speeds.
Effects of fluid thermophysical properties on cavitating flows
Chen, Tairan; Huang, Biao; Wang, Guoyu; Wang, Kun [Beijing Institute of Technology, Beijing (China)
2015-10-15
We studied the thermo-fluid cavitating flows and evaluated the effects of physical properties on cavitation behaviors. The thermo-fluid (including liquid nitrogen, liquid hydrogen and hot water) cavitating flows around a 2D hydrofoil were numerically investigated. The Favre-averaged Navier-Stokes equations with the enthalpy-based energy equation, transport equation-based cavitation model, and the k- ω SST turbulence model were applied. The thermodynamic parameter ∑, defined as ∑=(P{sub v}{sup 2}L{sup 2})/(P{sub l}{sup 2}C{sub v}T{sub ∞} √ε{sub I}) was used to assess the thermodynamic effects on cavitating flows. The results manifest that the thermal energy solution case yields a substantially shorter and mushier cavity attached on the hydrofoil due to the thermodynamic effects, which shows better agreement with the experimental data. The temperature drop inside the cavity decreases the local saturated vapor pressure and hence increases the local cavitation number; it could delay or suppress the occurrence and development of the cavitation behavior. The thermodynamic effects can be evaluated by thermophysical properties under the same free-stream conditions; the thermodynamic parameter ∑ is shown to be critical in accurately predicting the thermodynamic effects on cavitating flows. The surrogate-based global sensitivity analysis of liquid nitrogen cavitating flow suggests that ρ{sub v}, C{sub l} and L could significantly influence temperature drop and cavity structure in the existing numerical framework, while ρv plays the dominant role on temperature drop when properties vary with changing temperature. The liquid viscosity ml slightly affects the flow structure but hardly affects the temperature distribution.
Visualization periodic flows in a continuously stratified fluid.
Bardakov, R.; Vasiliev, A.
2012-04-01
To visualize the flow pattern of viscous continuously stratified fluid both experimental and computational methods were developed. Computational procedures were based on exact solutions of set of the fundamental equations. Solutions of the problems of flows producing by periodically oscillating disk (linear and torsion oscillations) were visualized with a high resolutions to distinguish small-scale the singular components on the background of strong internal waves. Numerical algorithm of visualization allows to represent both the scalar and vector fields, such as velocity, density, pressure, vorticity, stream function. The size of the source, buoyancy and oscillation frequency, kinematic viscosity of the medium effects were traced in 2D an 3D posing problems. Precision schlieren instrument was used to visualize the flow pattern produced by linear and torsion oscillations of strip and disk in a continuously stratified fluid. Uniform stratification was created by the continuous displacement method. The buoyancy period ranged from 7.5 to 14 s. In the experiments disks with diameters from 9 to 30 cm and a thickness of 1 mm to 10 mm were used. Different schlieren methods that are conventional vertical slit - Foucault knife, vertical slit - filament (Maksoutov's method) and horizontal slit - horizontal grating (natural "rainbow" schlieren method) help to produce supplementing flow patterns. Both internal wave beams and fine flow components were visualized in vicinity and far from the source. Intensity of high gradient envelopes increased proportionally the amplitude of the source. In domains of envelopes convergence isolated small scale vortices and extended mushroom like jets were formed. Experiments have shown that in the case of torsion oscillations pattern of currents is more complicated than in case of forced linear oscillations. Comparison with known theoretical model shows that nonlinear interactions between the regular and singular flow components must be taken
Fluid Flow Prediction with Development System Interwell Connectivity Influence
Bolshakov, M.; Deeva, T.; Pustovskikh, A.
2016-03-01
In this paper interwell connectivity has been studied. First of all, literature review of existing methods was made which is divided into three groups: Statistically-Based Methods, Material (fluid) Propagation-Based Methods and Potential (pressure) Change Propagation-Based Method. The disadvantages of the first and second groups are as follows: methods do not involve fluid flow through porous media, ignore any changes of well conditions (BHP, skin factor, etc.). The last group considers changes of well conditions and fluid flow through porous media. In this work Capacitance method (CM) has been chosen for research. This method is based on material balance and uses weight coefficients lambdas to assess well influence. In the next step synthetic model was created for examining CM. This model consists of an injection well and a production well. CM gave good results, it means that flow rates which were calculated by analytical method (CM) show matching with flow rate in model. Further new synthetic model was created which includes six production and one injection wells. This model represents seven-spot pattern. To obtain lambdas weight coefficients, the delta function was entered using by minimization algorithm. Also synthetic model which has three injectors and thirteen producer wells was created. This model simulates seven-spot pattern production system. Finally Capacitance method (CM) has been adjusted on real data of oil Field Ω. In this case CM does not give enough satisfying results in terms of field data liquid rate. In conclusion, recommendations to simplify CM calculations were given. Field Ω is assumed to have one injection and one production wells. In this case, satisfying results for production rates and cumulative production were obtained.
Fluid flow in nanopores: An examination of hydrodynamic boundary conditions
Sokhan, V. P.; Nicholson, D.; Quirke, N.
2001-08-01
Steady-state Poiseuille flow of a simple fluid in carbon slit pores under a gravity-like force is simulated using a realistic empirical many-body potential model for carbon. In this work we focus on the small Knudsen number regime, where the macroscopic equations are applicable, and simulate different wetting conditions by varying the strength of fluid-wall interactions. We show that fluid flow in a carbon pore is characterized by a large slip length even in the strongly wetting case, contrary to the predictions of Tolstoi's theory. When the surface density of wall atoms is reduced to values typical of a van der Waals solid, the streaming velocity profile vanishes at the wall, in accordance with earlier findings. From the velocity profiles we have calculated the slip length and by analyzing temporal profiles of the velocity components of particles colliding with the wall we obtained values of the Maxwell coefficient defining the fraction of molecules thermalized by the wall.
Microscopic and continuum descriptions of Janus motor fluid flow fields
Reigh, Shang Yik; Huang, Mu-Jie; Schofield, Jeremy; Kapral, Raymond
2016-11-01
Active media, whose constituents are able to move autonomously, display novel features that differ from those of equilibrium systems. In addition to naturally occurring active systems such as populations of swimming bacteria, active systems of synthetic self-propelled nanomotors have been developed. These synthetic systems are interesting because of their potential applications in a variety of fields. Janus particles, synthetic motors of spherical geometry with one hemisphere that catalyses the conversion of fuel to product and one non-catalytic hemisphere, can propel themselves in solution by self-diffusiophoresis. In this mechanism, the concentration gradient generated by the asymmetric catalytic activity leads to a force on the motor that induces fluid flows in the surrounding medium. These fluid flows are studied in detail through microscopic simulations of Janus motor motion and continuum theory. It is shown that continuum theory is able to capture many, but not all, features of the dynamics of the Janus motor and the velocity fields of the fluid. This article is part of the themed issue 'Multiscale modelling at the physics-chemistry-biology interface'.
Modeling of dilute and dense dispersed fluid-particle flow
Laux, Harald
1998-08-01
A general two-fluid model is derived and applied in CFD computations to various test cases of important industrial multiphase flows. It is general in the sense of its applicability to dilute and dense dispersed fluid-particle flows. The model is limited to isothermal flow without mass transfer and only one particle phase is described. The instantaneous fluid phase equations, including the phase interaction terms, are derived from a volume averaging technique, and the instantaneous particle phase equations are derived from the kinetic theory of granular material. Whereas the averaging procedure, the treatment of the interaction terms, and the kinetic theory approach have been reported in literature prior to this work the combination of the approaches is new. The resulting equations are derived without ambiguity in the interpretation of the particle phase pressure (equation-of-state of particle phase). The basic modeling for the particle phase is improved in two steps. Because in the basic modeling only stresses due to kinetic and collisional interactions are included, a simple model for an effective viscosity is developed in order to allow also frictional stresses within the particle phase. Moreover, turbulent stresses and turbulent dispersion of particles play often an important role for the transport processes. Therefore in a second step, a two-equation turbulence model for both fluid and particle phase turbulence is derived by applying the phasic average to the instantaneous equations. The resulting k-{epsilon}-k{sup d}-{epsilon}{sup d} model is new. Mathematical closure is attempted such that the resulting set of equations is valid for both dilute arid dense flows. During the development of the closure relations a clear distinction is made between granular or ''viscous'' microscale fluctuations and turbulent macro scale fluctuations (true particle turbulence) within the particle phase. The set of governing equations is discretized by using a
Observing Behavior of Fluid Flow through Carbon Nanotube Arrays
Jensen, Anna T.
This work establishes a platform technique for visualizing fluid transport through Anoidisc Alumina Oxide (AAO) membranes, which can be applied to Carbon Nanotube (CNT) arrays, and allow for the testing of the effects of other parameters on flow. Arrays of CNTs have shown significant promise for delivering biomolecules into cells with high efficiency while maintaining cell viability. In these applications, biomolecules flow through CNT arrays manufactured in our lab using Template-Based Chemical Vapor Deposition. By culturing cells on the opposite side of the array, they can be used to transfect biomolecules into cells. In this research, it was discovered that the transfection rate was dependent on the type of biomolecule being delivered into the cells. It was also inferred that the number of CNTs the cells covered would affect the transfection rate. In order to characterize flow through the CNT arrays, an experiment was designed and conducted to test the effect of changing the number of active CNTs. Preliminary testing showed the occurrence of an unknown error in the CNT array manufacturing process which prevented material from flowing through the CNT arrays. As a result, the study was modified to characterize flow through AAO membranes, which serve as the template for the CNTs. To accomplish this, a flow device was developed which restricted flow to a predefined circular area. Three different diameters were tested 6 mm, 4 mm, and 2 mm. Flow data was taken using fluorescent dye, as it diffused through the AAO into a volume of water on the opposite side, fluorescent intensity would increase. This data was plotted against time and used to model flow for the three tested diameters. The results indicated that the total time for diffusion increased as the diameters decreased. However, the relationship between the number of exposed pores and the flow time were not directly related, meaning the amount of flow through one pore changes with the total number of exposed
Flow of a viscous nematic fluid around a sphere
Gómez-González, Manuel
2013-01-01
We analyze the creeping flow generated by a spherical particle moving through a viscous fluid with nematic directional order, in which momentum diffusivity is anisotropic and which opposes resistance to bending. Specifically, we provide closed-form analytical expressions for the response function, i.e. the equivalent to Stokes's drag formula for nematic fluids. Particular attention is given to the rotationally pseudo-isotropic condition defined by zero resistance to bending, and to the strain pseudo-isotropic condition defined by isotropic momentum diffusivity. We find the former to be consistent with the rheology of biopolymer networks and the latter to be closer to the rheology of nematic liquid crystals. These "pure" anisotropic conditions are used to benchmark existing particle tracking microrheology methods that provide effective directional viscosities by applying Stokes's drag law separately in different directions. We find that the effective viscosity approach is phenomenologically justified in rotati...
Thermodynamic optimization of fluid flow over an isothermal moving plate
A. Malvandi
2013-09-01
Full Text Available In this paper, entropy generation minimization (EGM was employed in order to achieve a thermodynamic optimization of fluid flow and heat transfer over a flat plate. The basic boundary layer equations including continuity, momentum, energy, and entropy generation have been reduced to a two-point boundary value problem via similarity variables and solved numerically via Runge–Kutta–Fehlberg scheme. The novelty of this study was to consider the effects of velocity ratio λ – which represents the ratio of the wall velocity to the free stream fluid velocity – in a thermodynamic system. Focusing on the velocity ratio as a pivotal parameter, in view of minimizing the entropy generation, the optimum value of λ=λo was achieved. Moreover, considering Bejan number, it was shown that the region, in which the maximum entropy generates, gets closer to the plate as λ increases.
Fluid flow and permeabilities in basement fault zones
Hollinsworth, Allan; Koehn, Daniel
2017-04-01
Fault zones are important sites for crustal fluid flow, specifically where they cross-cut low permeability host rocks such as granites and gneisses. Fluids migrating through fault zones can cause rheology changes, mineral precipitation and pore space closure, and may alter the physical and chemical properties of the host rock and deformation products. It is therefore essential to consider the evolution of permeability in fault zones at a range of pressure-temperature conditions to understand fluid migration throughout a fault's history, and how fluid-rock interaction modifies permeability and rheological characteristics. Field localities in the Rwenzori Mountains, western Uganda and the Outer Hebrides, north-west Scotland, have been selected for field work and sample collection. Here Archaean-age TTG gneisses have been faulted within the upper 15km of the crust and have experienced fluid ingress. The Rwenzori Mountains are an anomalously uplifted horst-block located in a transfer zone in the western rift of the East African Rift System. The north-western ridge is characterised by a tectonically simple western flank, where the partially mineralised Bwamba Fault has detached from the Congo craton. Mineralisation is associated with hydrothermal fluids heated by a thermal body beneath the Semliki rift, and has resulted in substantial iron oxide precipitation within porous cataclasites. Non-mineralised faults further north contain foliated gouges and show evidence of leaking fluids. These faults serve as an analogue for faults associated with the Lake Albert oil and gas prospects. The Outer Hebrides Fault Zone (OHFZ) was largely active during the Caledonian Orogeny (ca. 430-400 Ma) at a deeper crustal level than the Ugandan rift faults. Initial dry conditions were followed by fluid ingress during deformation that controlled its rheological behaviour. The transition also altered the existing permeability. The OHFZ is a natural laboratory in which to study brittle fault
Langevin and diffusion equation of turbulent fluid flow
Brouwers, J. J. H.
2010-08-01
A derivation of the Langevin and diffusion equations describing the statistics of fluid particle displacement and passive admixture in turbulent flow is presented. Use is made of perturbation expansions. The small parameter is the inverse of the Kolmogorov constant C 0 , which arises from Lagrangian similarity theory. The value of C 0 in high Reynolds number turbulence is 5-6. To achieve sufficient accuracy, formulations are not limited to terms of leading order in C0 - 1 including terms next to leading order in C0 - 1 as well. Results of turbulence theory and statistical mechanics are invoked to arrive at the descriptions of the Langevin and diffusion equations, which are unique up to truncated terms of O ( C0 - 2 ) in displacement statistics. Errors due to truncation are indicated to amount to a few percent. The coefficients of the presented Langevin and diffusion equations are specified by fixed-point averages of the Eulerian velocity field. The equations apply to general turbulent flow in which fixed-point Eulerian velocity statistics are non-Gaussian to a degree of O ( C0 - 1 ) . The equations provide the means to calculate and analyze turbulent dispersion of passive or almost passive admixture such as fumes, smoke, and aerosols in areas ranging from atmospheric fluid motion to flows in engineering devices.
SPH numerical simulation of fluid flow through a porous media
Klapp-Escribano, Jaime; Mayoral-Villa, Estela; Rodriguez-Meza, Mario Alberto; de La Cruz-Sanchez, Eduardo; di G Sigalotti, Leonardo; Inin-Abacus Collaboration; Ivic Collaboration
2013-11-01
We have tested an improved a method for 3D SPH simulations of fluid flow through a porous media using an implementation of this method with the Dual-Physics code. This improvement makes it possible to simulate many particles (of the order of several million) in reasonable computer times because its execution on GPUs processors makes it possible to reduce considerably the simulation cost for large systems. Modifications in the initial configuration have been implemented in order to simulate different arrays and geometries for the porous media. The basic tests were reproduced and the performance was analyzed. Our 3D simulations of fluid flow through a saturated homogeneous porous media shows a discharge velocity proportional to the hydraulic gradient reproducing Darcy's law at small body forces. The results are comparable with values obtained in previous work and published in the literature for simulations of flow through periodic porous media. Our simulations for a non saturated porous media produce adequate qualitative results showing that a non steady state is generated. The relaxation time for these systems were obtained. Work partially supported by Cinvestav-ABACUS, CONACyT grant EDOMEX-2011-C01-165873.
Combining multiblock and detailed fluid flow models (LOVI) - MASIT17
Alopaeus, V.; Moilanen, P.; Visuri, O.; Laakkonen, M.; Aittamaa, J. (Helsinki University of Technology, Faculty of Chemistry and Materials Sciences, Department of Biotechnology and Chemical Technology, Espoo (Finland)); Heiskanen, K.; Wierink, G. (Helsinki University of Technology, Faculty of Chemistry and Materials Sciences, Department of Materials Science and Engineering, Espoo (Finland)); Manninen, M.; Seppaelae, M. (VTT Technical Research Centre of Finland, Espoo (Finland))
2008-07-01
The goal of this research project is to develop models for scale-up, design and operation of heterogeneous reactors. By computing a detailed fluid flow field and using it in a multiblock-model the computing times can be kept reasonable. Our modelling is based on phenomenological models verified on experimental results. Several experimental apparatuses have been used to study gas-liquid flow (tapered channel, 14/200dm3 stirred vessels and the 'giraffe') and bubble-particle interactions. A particle imaging velocimetry (PIV) apparatus is being purchased during 2008 to study fluid flow fields. There has been extensive experimental activity. During this project phenomenological models have been verified, numerical methods for the calculation of population balances have been improved, a novel local mixing time analysis method has been developed and automated multiblock generation algorithms have been developed. A method of evaluating CFD results with a single glance with a two-block model has been introduced. Fermentation process of Galilaeus and the flotation cell of Outotec have been modelled. (orig.)
Mechanics of fluid flow over compliant wrinkled polymeric surfaces
Raayai, Shabnam; McKinley, Gareth; Boyce, Mary
2014-03-01
Skin friction coefficients (based on frontal area) of sharks and dolphins are lower than birds, fish and swimming beetles. By either exploiting flow-induced changes in their flexible skin or microscale textures, dolphins and sharks can change the structure of the fluid flow around them and thus reduce viscous drag forces on their bodies. Inspired by this ability, investigators have tried using compliant walls and riblet-like textures as drag reduction methods in aircraft and marine industries and have been able to achieve reductions up to 19%. Here we investigate flow-structure interaction and wrinkling of soft polymer surfaces that can emulate shark riblets and dolphin's flexible skin. Wrinkling arises spontaneously as the result of mismatched deformation of a thin stiff coating bound to a thick soft elastic substrate. Wrinkles can be fabricated by controlling the ratio of the stiffness of the coating and substrate, the applied displacement and the thickness of the coating. In this work we will examine the evolution in the kinematic structures associated with steady viscous flow over the polymer wrinkled surfaces and in particular compare the skin friction with corresponding results for flow over non-textured and rigid surfaces.
Fluctuating multicomponent lattice Boltzmann model.
Belardinelli, D; Sbragaglia, M; Biferale, L; Gross, M; Varnik, F
2015-02-01
Current implementations of fluctuating lattice Boltzmann equations (FLBEs) describe single component fluids. In this paper, a model based on the continuum kinetic Boltzmann equation for describing multicomponent fluids is extended to incorporate the effects of thermal fluctuations. The thus obtained fluctuating Boltzmann equation is first linearized to apply the theory of linear fluctuations, and expressions for the noise covariances are determined by invoking the fluctuation-dissipation theorem directly at the kinetic level. Crucial for our analysis is the projection of the Boltzmann equation onto the orthonormal Hermite basis. By integrating in space and time the fluctuating Boltzmann equation with a discrete number of velocities, the FLBE is obtained for both ideal and nonideal multicomponent fluids. Numerical simulations are specialized to the case where mean-field interactions are introduced on the lattice, indicating a proper thermalization of the system.
An annotation system for 3D fluid flow visualization
Loughlin, Maria M.; Hughes, John F.
1995-01-01
Annotation is a key activity of data analysis. However, current systems for data analysis focus almost exclusively on visualization. We propose a system which integrates annotations into a visualization system. Annotations are embedded in 3D data space, using the Post-it metaphor. This embedding allows contextual-based information storage and retrieval, and facilitates information sharing in collaborative environments. We provide a traditional database filter and a Magic Lens filter to create specialized views of the data. The system has been customized for fluid flow applications, with features which allow users to store parameters of visualization tools and sketch 3D volumes.
Fluid flow and solute segregation in EFG crystal growth process
Bunoiu, O.; Nicoara, I.; Santailler, J. L.; Duffar, T.
2005-02-01
The influence of the die geometry and various growth conditions on the fluid flow and on the solute distribution in EFG method has been studied using numerical simulation. The commercial FIDAP software has been used in order to solve the momentum and mass transfer equations in the capillary channel and in the melt meniscus. Two types of shaper design are studied and the results are in good agreement with the void distribution observed in rod-shaped sapphire crystals grown by the EFG method in the various configurations.
Characteristics of Electrorheological Fluid Flow Between Two Concentric Cylinders
PENG Jie; ZHU Ke-Qin; XI Bao-Shu
2000-01-01
The characteristics of Couette flow of electrorheological fluid (ERF) between concentric cylinders is dependent on the parameter β, which is in the yield stress formula of ERF. In the case of β ＞ 2, the yield region locates between the yield surface and the outer cylinder. In the case of β ＜ 2, the yield region locates between the yield surface and the inner cylinder. When β=2, there is no yield surface. Steady and time dependent numerical results in relation to different β are presented and discussed.
Linear Inviscid Damping for Couette Flow in Stratified Fluid
Yang, Jincheng
2016-01-01
We study the inviscid damping of Coutte flow with an exponentially stratified density. The optimal decay rates of the velocity field and density are obtained for general perturbations with minimal regularity. For Boussinesq approximation model, the decay rates we get are consistent with the previous results in the literature. We also study the decay rates for the full equations of stratified fluids, which were not studied before. For both models, the decay rates depend on the Richardson number in a very similar way. Besides, we also study the inviscid damping of perturbations due to the exponential stratification when there is no shear.
k Spectrum of Passive Scalars in Lagrangian Chaotic Fluid Flows
Antonsen, Thomas M., Jr.; Fan, Zhencan Frank; Ott, Edward
1995-08-01
An eikonal-type description for the evolution of k spectra of passive scalars convected in a Lagrangian chaotic fluid flow is shown to accurately reproduce results from orders of magnitude more time consuming computations based on the full passive scalar partial differential equation. Furthermore, the validity of the reduced description, combined with concepts from chaotic dynamics, allows new theoretical results on passive scalar k spectra to be obtained. Illustrative applications are presented to long-time passive scalar decay, and to Batchelor's law k spectrum and its diffusive cutoff.
Heat transfer and fluid flow in nuclear systems
Fenech, Henri
1982-01-01
Heat Transfer and Fluid in Flow Nuclear Systems discusses topics that bridge the gap between the fundamental principles and the designed practices. The book is comprised of six chapters that cover analysis of the predicting thermal-hydraulics performance of large nuclear reactors and associated heat-exchangers or steam generators of various nuclear systems. Chapter 1 tackles the general considerations on thermal design and performance requirements of nuclear reactor cores. The second chapter deals with pressurized subcooled light water systems, and the third chapter covers boiling water reacto
A Study on Viscoelastic Fluid Flow in a Square-Section 90-Degrees Bend
Mizue Munekata; Kazuyoshi Matsuzaki; Hideki Ohba
2003-01-01
It is well known that the drag-reducing effect is obtained in a surfactant solution flow in a straight pipe. We investigate about a viscoelastic fluid flow such as a surfactant solution flow in a square-section 90° bend. In the experimental study, drag-reducing effect and velocity field in a surfactant solution flow are investigated by measurements of wall pressure loss and LDV measurements. For the numerical method, LES with FENE-P model is used in the viscoelastic fluid flow in the bend. The flow characteristics of viscoelastic fluid are discussed compared with that of a Newtonian fluid.
Fluid flow of incompressible viscous fluid through a non-linear elastic tube
Lazopoulos, A.; Tsangaris, S. [National Technical University of Athens, Fluids Section, School of Mechanical Engineering, Zografou, Athens (Greece)
2008-11-15
The study of viscous flow in tubes with deformable walls is of specific interest in industry and biomedical technology and in understanding various phenomena in medicine and biology (atherosclerosis, artery replacement by a graft, etc) as well. The present work describes numerically the behavior of a viscous incompressible fluid through a tube with a non-linear elastic membrane insertion. The membrane insertion in the solid tube is composed by non-linear elastic material, following Fung's (Biomechanics: mechanical properties of living tissue, 2nd edn. Springer, New York, 1993) type strain-energy density function. The fluid is described through a Navier-Stokes code coupled with a system of non linear equations, governing the interaction with the membrane deformation. The objective of this work is the study of the deformation of a non-linear elastic membrane insertion interacting with the fluid flow. The case of the linear elastic material of the membrane is also considered. These two cases are compared and the results are evaluated. The advantages of considering membrane nonlinear elastic material are well established. Finally, the case of an axisymmetric elastic tube with variable stiffness along the tube and membrane sections is studied, trying to substitute the solid tube with a membrane of high stiffness, exhibiting more realistic response. (orig.)
Complex fluid flow modeling with SPH on GPU
Bilotta, Giuseppe; Hérault, Alexis; Del Negro, Ciro; Russo, Giovanni; Vicari, Annamaria
2010-05-01
We describe an implementation of the Smoothed Particle Hydrodynamics (SPH) method for the simulation of complex fluid flows. The algorithm is entirely executed on Graphic Processing Units (GPUs) using the Compute Unified Device Architecture (CUDA) developed by NVIDIA and fully exploiting their computational power. An increase of one to two orders of magnitude in simulation speed over equivalent CPU code is achieved. A complete modeling of the flow of a complex fluid such as lava is challenging from the modelistic, numerical and computational points of view. The natural topography irregularities, the dynamic free boundaries and phenomena such as solidification, presence of floating solid bodies or other obstacles and their eventual fragmentation make the problem difficult to solve using traditional numerical methods (finite volumes, finite elements): the need to refine the discretization grid in correspondence of high gradients, when possible, is computationally expensive and with an often inadequate control of the error; for real-world applications, moreover, the information needed by the grid refinement may not be available (e.g. because the Digital Elevation Models are too coarse); boundary tracking is also problematic with Eulerian discretizations, more so with complex fluids due to the presence of internal boundaries given by fluid inhomogeneity and presence of solidification fronts. An alternative approach is offered by mesh-free particle methods, that solve most of the problems connected to the dynamics of complex fluids in a natural way. Particle methods discretize the fluid using nodes which are not forced on a given topological structure: boundary treatment is therefore implicit and automatic; the movement freedom of the particles also permits the treatment of deformations without incurring in any significant penalty; finally, the accuracy is easily controlled by the insertion of new particles where needed. Our team has developed a new model based on the
Timing of Fluid Flow During Exhumation of Deeply Subducted Continent
Zheng, Y.; Gao, T.; Wu, Y.; Gong, B.
2005-12-01
Quartz veins are common within UHP eclogites in the Dabie-Sulu orogenic belt of China. While their formation has been linked to dehydration reactions, time of veining has been uncertain during either subduction or exhumation. SHRIMP U-Pb dating for zircons from kyanite-quartz vein and its host eclogite in the Dabie orogen yields two groups of age at 212±7 Ma and 181±13 Ma, respectively. They are significant younger not only than SHRIMP zircon U-Pb ages of 243±4 and 224±3 Ma for host eclogite, but also than known UHP metamorphic ages of 234±4 to 227±2 Ma as dated by the SHRIMP U-Pb technique for coesite-bearing domains of zircon. The U-Pb age of 224±3 Ma for the eclogite dates zircon growth at the onset of HP eclogite-facies recrystallization during exhumation. Corresponding temperatures may be about 670°C as estimated for both eclogite-facies recrystallization and veining from a petrological study. The second group of zircon U-Pb age at 181±13 Ma is much later than the HP-UHP-HP metamorphic events during the orogenic cycle and thus may not be relevant to post-collisional exhumation. Therefore, the two groups of vein age date the two episodes of fluid flow, respectively, due to decompression dehydration during exhumation and heating dehydration in response to breakup of supercontinent Pangea. This provides for the first time the radiometric dates for timing of fracture fluid flow that transports both mass and heat during plate collision. Laser fluorination O isotope analyses show the almost same δ18O values for the minerals of both vein and eclogite, indicating the same origin of fluid and material for them and thus internally derived fluid for veining. High O isotope temperatures of 695±20 to 715±35°C are obtained for Qz-Ky and Qz-Gt pairs, suggesting the attainment of O isotope reequilibration during the HP eclogite-facies recrystallization. On the other hand, low O isotope temperatures of 490±10 to 510±15°C occur in Qz-Rt and Qz-Zo pairs
Characterization of Fluid Flow in Paper-Based Microfluidic Systems
Walji, Noosheen; MacDonald, Brendan
2014-11-01
Paper-based microfluidic devices have been presented as a viable low-cost alternative with the versatility to accommodate many applications in disease diagnosis and environmental monitoring. Current microfluidic designs focus on the use of silicone and PDMS structures, and several models have been developed to describe these systems; however, the design process for paper-based devices is hindered by a lack of prediction capability. In this work we simplify the complex underlying physics of the capillary-driven flow mechanism in a porous medium and generate a practical numerical model capable of predicting the flow behaviour. We present our key insights regarding the properties that dictate the behaviour of fluid wicking in paper-based microfluidic devices. We compare the results from our model to experiments and discuss the application of our model to design of paper-based microfluidic devices for arsenic detection in drinking water in Bangladesh.
Fluid Flow in Continuous Casting Mold with a Configured Nozzle
王镭; 沈厚发; 柳百成
2004-01-01
The influence of a configured nozzle on the turbulent fluid flow in a continuous casting mold was investigated using the simulation program Visual Cast, which used the finite difference method and the SIMPLER algorithm. CAD software was used to construct the complicated nozzle in the calculational region. The simulation accuracy was validated by comparison with the classic driven cavity flow problem. The simulation results agree well with water modeling experiments. The simulations show that the velocity distribution at the nozzle port is uneven and the jet faces downward more than the nozzle outlet. Simulations with a configured nozzle and the inlet velocity at the nozzle entrance give precise results and overcome the traditional difficulty in determining the nozzle outlet velocity.
Fluid dynamics in airway bifurcations: III. Localized flow conditions.
Martonen, T B; Guan, X; Schreck, R M
2001-04-01
Localized flow conditions (e.g., backflows) in transition regions between parent and daughter airways of bifurcations were investigated using a computational fluid dynamics software code (FIDAP) with a Cray T90 supercomputer. The configurations of the bifurcations were based on Schreck s (1972) laboratory models. The flow intensities and spatial regions of reversed motion were simulated for different conditions. The effects of inlet velocity profiles, Reynolds numbers, and dimensions and orientations of airways were addressed. The computational results showed that backflow was increased for parabolic inlet conditions, larger Reynolds numbers, and larger daughter-to-parent diameter ratios. This article is the third in a systematic series addressed in this issue; the first addressed primary velocity patterns and the second discussed secondary currents.
Mapping flow distortion on oceanographic platforms using computational fluid dynamics
N. O'Sullivan
2013-10-01
Full Text Available Wind speed measurements over the ocean on ships or buoys are affected by flow distortion from the platform and by the anemometer itself. This can lead to errors in direct measurements and the derived parametrisations. Here we computational fluid dynamics (CFD to simulate the errors in wind speed measurements caused by flow distortion on the RV Celtic Explorer. Numerical measurements were obtained from the finite-volume CFD code OpenFOAM, which was used to simulate the velocity fields. This was done over a range of orientations in the test domain from −60 to +60° in increments of 10°. The simulation was also set up for a range of velocities, ranging from 5 to 25 m s−1 in increments of 0.5 m s−1. The numerical analysis showed close agreement to experimental measurements.
Extensional bundle waveguide techniques for measuring flow of hot fluids.
Lynnworth, Lawrence C; Liu, Yi; Umina, John A
2005-04-01
A bundle of acoustically slender metal rods, each thin compared to wavelength, tightly packed within a sheath, and welded closed at each end, provides a dispersion-free waveguide assembly that acts as a thermal buffer between a transducer and the hot fluid medium the flow of which is to be measured. Gas and steam flow applications have ranged up to 600 degrees C. Liquid applications have ranged from cryogenic (-160 degrees C) to 500 degrees C and include intermittent two-phase flows. The individual rods comprising the bundle usually are approximately one millimeter in diameter. The sheath, made of a pipe or tube, typically has an outside diameter of 12.7 to about 33 mm and usually is about 300 mm long. Materials for the sheath and bundle are selected to satisfy requirements of compatibility with the fluid as well as for acoustic properties. Corrosion-resistant alloys such as 316SS and titanium are commonly used. The buffers are used with transducers that are metal-encapsulated and certified for use in hazardous areas. They operate at a frequency in the range of 0.1 to 1 MHz. The radiating end of the buffer is usually flat and perpendicular to the buffer's main axis. In some cases the end of the buffer is stepped or angled. Angling the radiating faces at approximately 2 degrees to overcome beam drift at Mach 0.1 recently contributed to solving a high-temperature high-velocity flow measurement problem. The temperature in this situation was 300 degrees C, and the gas molecular weight was about 95, with pressure 0.9 to 1.1 bar.
Fluid mechanics experiments in oscillatory flow. Volume 1: Report
Seume, J.; Friedman, G.; Simon, T. W.
1992-01-01
Results of a fluid mechanics measurement program in oscillating flow within a circular duct are presented. The program began with a survey of transition behavior over a range of oscillation frequency and magnitude and continued with a detailed study at a single operating point. Such measurements were made in support of Stirling engine development. Values of three dimensionless parameters, Re(sub max), Re(sub w), and A(sub R), embody the velocity amplitude, frequency of oscillation and mean fluid displacement of the cycle, respectively. Measurements were first made over a range of these parameters which included operating points of all Stirling engines. Next, a case was studied with values of these parameters that are representative of the heat exchanger tubes in the heater section of NASA's Stirling cycle Space Power Research Engine (SPRE). Measurements were taken of the axial and radial components of ensemble-averaged velocity and rms-velocity fluctuation and the dominant Reynolds shear stress, at various radial positions for each of four axial stations. In each run, transition from laminar to turbulent flow, and its reverse, were identified and sufficient data was gathered to propose the transition mechanism. Models of laminar and turbulent boundary layers were used to process the data into wall coordinates and to evaluate skin friction coefficients. Such data aids in validating computational models and is useful in comparing oscillatory flow characteristics to those of fully-developed steady flow. Data were taken with a contoured entry to each end of the test section and with flush square inlets so that the effects of test section inlet geometry on transition and turbulence are documented. Volume 1 contains the text of the report including figures and supporting appendices. Volume 2 contains data reduction program listings and tabulated data (including its graphical presentation).
Fluid Flow Phenomenon in a Three-Bladed Power-Generating Archimedes Screw Turbine
Tineke Saroinsong; Rudy Soenoko; Slamet Wahyudi; Mega N Sasongko
2016-01-01
Experimental studies of the Archimedes screw turbine are applied as a micro hydro power plant for low head focused on the fluid flow. Fluid flow on a screw turbine is not completely filled water flow there is still a free surface between the water fluid and atmospheric air. Except the screw geometry, the turbine screw free surface allows the flow phenomena that are important in the process of turbine screw power generation. The Archimedes screw turbine main driving force is the fl...
Fluid Flow Phenomenon in a Three-Bladed Power-Generating Archimedes Screw Turbine
2016-01-01
Experimental studies of the Archimedes screw turbine are applied as a micro hydro power plant for low head focused on the fluid flow. Fluid flow on a screw turbine is not completely filled water flow there is still a free surface between the water fluid and atmospheric air. Except the screw geometry, the turbine screw free surface allows the flow phenomena that are important in the process of turbine screw power generation. The Archimedes screw turbine main driving force is the fl...
Modeling of dilute and dense dispersed fluid-particle flow
Laux, Harald
1998-08-01
A general two-fluid model is derived and applied in CFD computations to various test cases of important industrial multiphase flows. It is general in the sense of its applicability to dilute and dense dispersed fluid-particle flows. The model is limited to isothermal flow without mass transfer and only one particle phase is described. The instantaneous fluid phase equations, including the phase interaction terms, are derived from a volume averaging technique, and the instantaneous particle phase equations are derived from the kinetic theory of granular material. Whereas the averaging procedure, the treatment of the interaction terms, and the kinetic theory approach have been reported in literature prior to this work the combination of the approaches is new. The resulting equations are derived without ambiguity in the interpretation of the particle phase pressure (equation-of-state of particle phase). The basic modeling for the particle phase is improved in two steps. Because in the basic modeling only stresses due to kinetic and collisional interactions are included, a simple model for an effective viscosity is developed in order to allow also frictional stresses within the particle phase. Moreover, turbulent stresses and turbulent dispersion of particles play often an important role for the transport processes. Therefore in a second step, a two-equation turbulence model for both fluid and particle phase turbulence is derived by applying the phasic average to the instantaneous equations. The resulting k-{epsilon}-k{sup d}-{epsilon}{sup d} model is new. Mathematical closure is attempted such that the resulting set of equations is valid for both dilute arid dense flows. During the development of the closure relations a clear distinction is made between granular or ''viscous'' microscale fluctuations and turbulent macro scale fluctuations (true particle turbulence) within the particle phase. The set of governing equations is discretized by using a
Two-Fluid Mathematical Models for Blood Flow in Stenosed Arteries: A Comparative Study
Sankar DS
2009-01-01
Full Text Available The pulsatile flow of blood through stenosed arteries is analyzed by assuming the blood as a two-fluid model with the suspension of all the erythrocytes in the core region as a non-Newtonian fluid and the plasma in the peripheral layer as a Newtonian fluid. The non-Newtonian fluid in the core region of the artery is assumed as a (i Herschel-Bulkley fluid and (ii Casson fluid. Perturbation method is used to solve the resulting system of non-linear partial differential equations. Expressions for various flow quantities are obtained for the two-fluid Casson model. Expressions of the flow quantities obtained by Sankar and Lee (2006 for the two-fluid Herschel-Bulkley model are used to get the data for comparison. It is found that the plug flow velocity and velocity distribution of the two-fluid Casson model are considerably higher than those of the two-fluid Herschel-Bulkley model. It is also observed that the pressure drop, plug core radius, wall shear stress and the resistance to flow are significantly very low for the two-fluid Casson model than those of the two-fluid Herschel-Bulkley model. Hence, the two-fluid Casson model would be more useful than the two-fluid Herschel-Bulkley model to analyze the blood flow through stenosed arteries.
Flow of fluids from matrix to fractures in rock
Lupo, M.J.
1987-01-01
The flow of a single-phase compressible fluid from the rock matrix to fractures was modeled using the pressure diffusion equation. Pressure histories are presented for homogeneous isotropic blocks bounded by planar fractures. The case of an infinite slab bounded by planes of constant pore pressure was studied. The slab was divided by a planar fracture perpendicular to the planes. Lateral flow was found to cease once equilibrium is reached between the fracture and the matrix. Disequilibrium is found to be short-lived for laboratory-sized specimens of typical reservoir rock. The most-important parameter in cross-flow is the distance l between the two planes of constan pore pressure. When a second fracture was added, parallel to the first, the cross-flow behavior was nearly identical to the one fracture case if the spacing of the fractures is greater than l. The pressure history of the blocks of the continuum model of naturally fractured reservoirs was examined with a discrete mathematical model. An analytical solution to the pressure diffusion equation with time dependent boundary conditions is presented for blocks in both a finite and infinite reservoir.
Meshless lattice Boltzmann method for the simulation of fluid flows.
Musavi, S Hossein; Ashrafizaadeh, Mahmud
2015-02-01
A meshless lattice Boltzmann numerical method is proposed. The collision and streaming operators of the lattice Boltzmann equation are separated, as in the usual lattice Boltzmann models. While the purely local collision equation remains the same, we rewrite the streaming equation as a pure advection equation and discretize the resulting partial differential equation using the Lax-Wendroff scheme in time and the meshless local Petrov-Galerkin scheme based on augmented radial basis functions in space. The meshless feature of the proposed method makes it a more powerful lattice Boltzmann solver, especially for cases in which using meshes introduces significant numerical errors into the solution, or when improving the mesh quality is a complex and time-consuming process. Three well-known benchmark fluid flow problems, namely the plane Couette flow, the circular Couette flow, and the impulsively started cylinder flow, are simulated for the validation of the proposed method. Excellent agreement with analytical solutions or with previous experimental and numerical results in the literature is observed in all the simulations. Although the computational resources required for the meshless method per node are higher compared to that of the standard lattice Boltzmann method, it is shown that for cases in which the total number of nodes is significantly reduced, the present method actually outperforms the standard lattice Boltzmann method.
Computational fluid flow and heat transfer. An engineering tool
Salcudean, Martha
1991-05-01
The purpose, method, and potential of computational fluid dynamics (CFD) are discussed. Some examples of CFD and heat transfer applied to engineering problems are described. Simulation of casting in a permanent mold, gallium arsenide crystal growth, and the computation of discharge coefficients in film cooling of turbine blades are briefly described. It is shown the the CFD methods help to improve the understanding of the physics involved. They allow the influence of various parameters on the product or process to be investigated in a relatively inexpensive way. CFD constitutes a predictive tool which allows for product or process optimization. Discretization and solution methods used in the present examples are briefly described. Some limitations of the CFD methods are illustrated. The error introduced by false diffusion is shown for laminar flow around a bluff body. The improvement obtained by a higher order scheme is discussed. Some difficulties related to turbulence modelling are illustrated for the flow and heat transfer around the same bluff body. Turbulent swirling flow between concentric annuli is also discussed. Problems related to the slow convergence rate and major improvements obtained through applying multigrid convergence acceleration methods are shown for two and three dimensional opposing jets penetrating into a main flow.
Geothermal heat exchanger with coaxial flow of fluids
Pejić Dragan M.
2005-01-01
Full Text Available The paper deals with a heat exchanger with coaxial flow. Two coaxial pipes of the secondary part were placed directly into a geothermal boring in such a way that geothermal water flows around the outer pipe. Starting from the energy balance of the exchanger formed in this way and the assumption of a study-state operating regime, a mathematical model was formulated. On the basis of the model, the secondary circle output temperature was determined as a function of the exchanger geometry, the coefficient of heat passing through the heat exchange areas, the average mass isobaric specific heats of fluid and mass flows. The input temperature of the exchanger secondary circle and the temperature of the geothermal water at the exit of the boring were taken as known values. Also, an analysis of changes in certain factors influencing the secondary water temperature was carried out. The parameters (flow temperature of the deep boring B-4 in Sijarinska Spa, Serbia were used. The theoretical results obtained indicate the great potential of this boring and the possible application of such an exchanger.
Vibrational shear flow of anisotropic viscoelastic fluid with small amplitudes
韩式方
2008-01-01
Using the constitutive equation of co-rotational derivative type for anisotropic viscoelastic fluid-liquid crystalline(LC),polymer liquids was developed.Two relaxation times are introduced in the equation:λn represents relaxation of the normal-symmetric stress components;λs represents relaxation of the shear-unsymmetric stress components.A vibrational rotating flow in gap between cylinders with small amplitudes is studied for the anisotropic viscoelastic fluid-liquid crystalline polymer.The time-dependent constitutive equation are linearized with respect to parameter of small amplitude.For the normal-symmetric part of stress tensor analytical expression of the shear stress is obtained by the constitutive equation.The complex viscosity,complex shear modulus,dynamic and imaginary viscosities,storage modulus and loss modulus are obtained for the normal-symmetric stress case which are defined by the common shear rate.For the shear-unsymmetric stress part,two shear stresses are obtained thus two complex viscosities and two complex shear modulus(i.e.first and second one) are given by the constitutive equation which are defined by rotating shear rate introduced by author.The dynamic and imaginary viscosities,storage modulus and loss modulus are given for each complex viscosities and complex shear modulus.Using the constituive equation the rotating flow with small amplitudes in gap between two coaxial cylinders is studied.
Variational formulation of ideal fluid flows according to gauge principle
Kambe, Tsutomu [IDS, Higashi-yama 2-11-3, Meguro-ku, Tokyo 153-0043 (Japan)], E-mail: kambe@ruby.dti.ne.jp
2008-06-30
On the basis of the gauge principle of field theory, a new variational formulation is presented for flows of an ideal fluid. The fluid is defined thermodynamically by mass density and entropy density, and its flow fields are characterized by symmetries of translation and rotation. The rotational transformations are regarded as gauge transformations as well as the translational ones. In addition to the Lagrangians representing the translation symmetry, a structure of rotation symmetry is equipped with a Lagrangian {lambda}{sub A} including the vorticity and a vector potential bilinearly. Euler's equation of motion is derived from variations according to the action principle. In addition, the equations of continuity and entropy are derived from the variations. Equations of conserved currents are deduced as the Noether theorem in the space of Lagrangian coordinate a. Without {lambda}{sub A}, the action principle results in the Clebsch solution with vanishing helicity. The Lagrangian {lambda}{sub A} yields non-vanishing vorticity and provides a source term of non-vanishing helicity. The vorticity equation is derived as an equation of the gauge field, and the {lambda}{sub A} characterizes topology of the field. The present formulation is comprehensive and provides a consistent basis for a unique transformation between the Lagrangian a space and the Eulerian x space. In contrast, with translation symmetry alone, there is an arbitrariness in the transformation between these spaces.
On numerical modelling of contact lines in fluid flows
Pelinovsky, Dmitry E
2013-01-01
We study numerically a reduced model proposed by Benilov and Vynnycky (J. Fluid Mech. 718 (2013), 481), who examined the behavior of a contact line with a 180-degree contact angle between liquid and a moving plate, in the context of a two-dimensional Couette flow. The model is given by a linear fourth-order advection-diffusion equation with an unknown velocity, which is to be determined dynamically from an additional boundary condition at the contact line. The main claim of Benilov and Vynnycky is that for any physically relevant initial condition, there is a finite positive time at which the velocity of the contact line tends to negative infinity, whereas the profile of the fluid flow remains regular. Additionally, it is claimed that the velocity behaves as the logarithmic function of time near the blow-up time. We simulate dynamics of this model under different initial conditions and confirm the first claim. However, we also show that the blow-up behavior is better approximated by a power function, compared...
Fluid mechanics experiments in oscillatory flow. Volume 2: Tabulated data
Seume, J.; Friedman, G.; Simon, T. W.
1992-01-01
Results of a fluid mechanics measurement program in oscillating flow within a circular duct are presented. The program began with a survey of transition behavior over a range of oscillation frequency and magnitude and continued with a detailed study at a single operating point. Such measurements were made in support of Stirling engine development. Values of three dimensionless parameters, Re sub max, Re sub w, and A sub R, embody the velocity amplitude, frequency of oscillation, and mean fluid displacement of the cycle, respectively. Measurements were first made over a range of these parameters that are representative of the heat exchanger tubes in the heater section of NASA's Stirling cycle Space Power Research Engine (SPRE). Measurements were taken of the axial and radial components of ensemble-averaged velocity and rms velocity fluctuation and the dominant Reynolds shear stress, at various radial positions for each of four axial stations. In each run, transition from laminar to turbulent flow, and its reverse, were identified and sufficient data was gathered to propose the transition mechanism. Volume 2 contains data reduction program listings and tabulated data (including its graphics).
Bridges, Craig; Rajagopal, K R
2010-01-01
We study the flow of a shear-thinning, chemically-reacting fluid that could be used to model the flow of the synovial fluid. The actual geometry where the flow of the synovial fluid takes place is very complicated, and therefore the governing equations are not amenable to simple mathematical analysis. In order to understand the response of the model, we choose to study the flow in a simple geometry. While the flow domain is not a geometry relevant to the flow of the synovial fluid in the human body it yet provides a flow which can be used to assess the efficacy of different models that have been proposed to describe synovial fluids. We study the flow in the annular region between two cylinders, one of which is undergoing unsteady oscillations about their common axis, in order to understand the quintessential behavioral characteristics of the synovial fluid. We use the three models suggested by Hron et al. [ J. Hron, J. M\\'{a}lek, P. Pust\\v{e}jovsk\\'{a}, K. R. Rajagopal, On concentration dependent shear-thinni...
Large-eddy simulation of supercritical fluid flow and combustion
Huo, Hongfa
The present study focuses on the modeling and simulation of injection, mixing, and combustion of real fluids at supercritical conditions. The objectives of the study are: (1) to establish a unified theoretical framework that can be used to study the turbulent combustion of real fluids; (2) to implement the theoretical framework and conduct numerical studies with the aim of improving the understanding of the flow and combustion dynamics at conditions representative of contemporary liquid-propellant rocket engine operation; (3) to identify the key design parameters and the flow variables which dictate the dynamics characteristics of swirl- and shear- coaxial injectors. The theoretical and numerical framework is validated by simulating the Sandia Flame D. The calculated axial and radial profiles of velocity, temperature, and mass fractions of major species are in reasonably good agreement with the experimental measurements. The conditionally averaged mass fraction profiles agree very well with the experimental results at different axial locations. The validated model is first employed to examine the flow dynamics of liquid oxygen in a pressure swirl injector at supercritical conditions. Emphasis is placed on analyzing the effects of external excitations on the dynamic response of the injector. The high-frequency fluctuations do not significantly affect the flow field as they are dissipated shortly after being introduced into the flow. However, the lower-frequency fluctuations are amplified by the flow. As a result, the film thickness and the spreading angle at the nozzle exit fluctuate strongly for low-frequency external excitations. The combustion of gaseous oxygen/gaseous hydrogen in a high-pressure combustion chamber for a shear coaxial injector is simulated to assess the accuracy and the credibility of the computer program when applied to a sub-scale model of a combustor. The predicted heat flux profile is compared with the experimental and numerical studies. The
Occurrence of turbulent flow conditions in supercritical fluid chromatography.
De Pauw, Ruben; Choikhet, Konstantin; Desmet, Gert; Broeckhoven, Ken
2014-09-26
Having similar densities as liquids but with viscosities up to 20 times lower (higher diffusion coefficients), supercritical CO2 is the ideal (co-)solvent for fast and/or highly efficient separations without mass-transfer limitations or excessive column pressure drops. Whereas in liquid chromatography the flow remains laminar in both the packed bed and tubing, except in extreme cases (e.g. in a 75 μm tubing, pure acetonitrile at 5 ml/min), a supercritical fluid can experience a transition from laminar to turbulent flow in more typical operation modes. Due to the significant lower viscosity, this transition for example already occurs at 1.3 ml/min for neat CO2 when using connection tubing with an ID of 127 μm. By calculating the Darcy friction factor, which can be plotted versus the Reynolds number in a so-called Moody chart, typically used in fluid dynamics, higher values are found for stainless steel than PEEK tubing, in agreement with their expected higher surface roughness. As a result turbulent effects are more pronounced when using stainless steel tubing. The higher than expected extra-column pressure drop limits the kinetic performance of supercritical fluid chromatography and complicates the optimization of tubing ID, which is based on a trade-off between extra-column band broadening and pressure drop. One of the most important practical consequences is the non-linear increase in extra-column pressure drop over the tubing downstream of the column which leads to an unexpected increase in average column pressure and mobile phase density, and thus decrease in retention. For close eluting components with a significantly different dependence of retention on density, the selectivity can significantly be affected by this increase in average pressure. In addition, the occurrence of turbulent flow is also observed in the detector cell and connection tubing. This results in a noise-increase by a factor of four when going from laminar to turbulent flow (e.g. going
Sylolites in carbonate rock: barriers to fluid flow?
Heap, M. J.; Baud, P.; Meredith, P. G.; Reuschlé, T.
2012-04-01
Stylolites, products of intergranular pressure-solution, form laterally-extensive, clay-enriched, planar features in porous sedimentary rocks. While mechanical strain localisation has been shown to dramatically decrease permeability in sedimentary rock (Baud et al., 2012), little attention has focused on the impact of chemical strain localisation. Potentially, stylolites could significantly influence regional fluid flow, an important consideration in, for example, geotechnical engineering and petroleum geoscience. To this end, we have performed a systematic study of the influence of stylolites (both parallel and perpendicular to the imposed flow direction) on the water and gas permeability of three oolitic limestones with porosities ranging from 6 to 16 %. Our experimental data show that the presence of stylolites increased the permeability of our limestone samples by about a factor of two (when compared to the adjacent stylolite-free material). However, the magnitude of the permeability increase was found to be independent of stylolite orientation and number. Porosity measurements demonstrated that core samples containing stylolites were consistently more porous than the adjacent stylolite-free material. We therefore suggest that it is the increase in porosity (or "stylolitic porosity", as a result of the presence of a stylolite) that is responsible for the observed modest increase in permeability. This conclusion is supported by x-ray computed tomographic images of the samples that show that sample density is unperturbed by the presence of a stylolite. We can further conclude that the impact of mechanical strain localisation (e.g., compaction bands, see Baud et al., 2012) has a much greater impact on fluid flow than chemical strain localisation (e.g., stylolites, this study).
Metamorphic fluid flow - a question of scale, crustal depth and bulk rock composition
Tracy, R.J.; Rye, D.M.
1985-01-01
Recent studies have indicated that certain metamorphic rocks interacted with significant volumes of aqueous fluid during their time-integrated mineral reaction history. Rather than demonstrating that pervasive fluid flow is general in metamorphic rocks, these documented cases instead suggest the likelihood of pronounced to extreme channelization of through-going in fluids in deep-seated metamorphic terranes (P>3 kbar). In rocks more shallowly buried, and therefore under low lithostatic stress, pervasive flow along grain boundaries and open microfractures probably occurred, as at Skye and the Skaergaard Complex. In higher pressure metamorphic environments, documented cases of high fluid/rock ratio make a strong case for flow channelized in veins or in impure marble aquifers where pore space and permeability were created by decarbonation reactions driven by infiltration of aqueous fluid. The source of this fluid may commonly be traced to a nearby wet granitic intrusion or quartz vein. As long as the pressurized source of aqueous fluid continued, outward flow was possible as fluid held open the intergranular pore space which was created only at the infiltration/reaction front where a reduction in solid volume accompanied reaction. Cessation or interruption of fluid flow would allow the pore space to close due to porous-rock strength being exceeded by lithostatic stress. Pervasive flow or aqueous fluid in deepseated metamorphic terranes is therefore probably limited to carbonate-bearing lithologies adjacent to sources of major volumes of fluid; otherwise, fluid flow is likely to be localized in fractures or veins.
Lundgren, P.; Lanari, R.; Manzo, M.; Sansosti, E.; Tizzani, P.; Hutnak, M.; Hurwitz, S.
2008-12-01
Campi Flegrei caldera, Italy, located along the Bay of Naples, has a long history of significant vertical deformation, with the most recent large uplift (>1.5m) occurring in 1983-1984. Each episode of uplift has been followed by a period of subsidence that decreases in rate with time and may be punctuated by brief episodes of lesser uplift. The large amplitude of the major uplifts that occur without volcanic activity, and the subsequent subsidence has been argued as evidence for hydrothermal amplification of any magmatic source. The later subsidence and its temporal decay have been argued as due to diffusion of the pressurized caldera fill material into the less porous surrounding country rock. We present satellite synthetic aperture radar (SAR) interferometry (InSAR) time series analysis of ERS and Envisat data from the European Space Agency, based on exploiting the Small Baseline Subset (SBAS) approach [Berardino et al., 2002]; this allows us to generate maps of relative surface deformation though time, beginning in 1992 through 2007, that are relevant to both ascending and descending satellite orbits. The general temporal behavior is one of subsidence punctuated by several lesser uplift episodes. The spatial pattern of deformation can be modeled through simple inflation/deflation sources in an elastic halfspace. Given the evidence to suggest that fluids may play a significant role in the temporal deformation of Campi Flegrei, rather than a purely magmatic or magma chamber-based interpretation, we model the temporal and spatial evolution of surface deformation as a hydrothermal fluid flow process. We use the TOUGH2-BIOT2 set of numerical codes [Preuss et al., 1999; Hsieh, 1996], which couple multi-phase (liquid-gas) and multi-component (H2O-CO2) fluid flow in a porous or fractured media with plane strain deformation and fluid flow in a linearly elastic porous medium. We explore parameters related to the depth and temporal history of fluid injection, fluid
Advanced tomographic flow diagnostics for opaque multiphase fluids
Torczynski, J.R.; O`Hern, T.J.; Adkins, D.R.; Jackson, N.B.; Shollenberger, K.A.
1997-05-01
This report documents the work performed for the ``Advanced Tomographic Flow Diagnostics for Opaque Multiphase Fluids`` LDRD (Laboratory-Directed Research and Development) project and is presented as the fulfillment of the LDRD reporting requirement. Dispersed multiphase flows, particularly gas-liquid flows, are industrially important to the chemical and applied-energy industries, where bubble-column reactors are employed for chemical synthesis and waste treatment. Due to the large range of length scales (10{sup {minus}6}-10{sup 1}m) inherent in real systems, direct numerical simulation is not possible at present, so computational simulations are forced to use models of subgrid-scale processes, the accuracy of which strongly impacts simulation fidelity. The development and validation of such subgrid-scale models requires data sets at representative conditions. The ideal measurement techniques would provide spatially and temporally resolved full-field measurements of the distributions of all phases, their velocity fields, and additional associated quantities such as pressure and temperature. No technique or set of techniques is known that satisfies this requirement. In this study, efforts are focused on characterizing the spatial distribution of the phases in two-phase gas-liquid flow and in three-phase gas-liquid-solid flow. Due to its industrial importance, the bubble-column geometry is selected for diagnostics development and assessment. Two bubble-column testbeds are utilized: one at laboratory scale and one close to industrial scale. Several techniques for measuring the phase distributions at conditions of industrial interest are examined: level-rise measurements, differential-pressure measurements, bulk electrical impedance measurements, electrical bubble probes, x-ray tomography, gamma-densitometry tomography, and electrical impedance tomography.
Stagnation-point flow of the Walters' B' fluid with slip
Labropulu, F.; Husain, I; Chinichian, M.
2004-01-01
The steady two-dimensional stagnation point flow of a non-Newtonian Walters' B' fluid with slip is studied. The fluid impinges on the wall either orthogonally or obliquely. A finite difference technique is employed to obtain solutions.
Aoki, Shigehisa, E-mail: aokis@cc.saga-u.ac.jp [Department of Pathology and Microbiology, Faculty of Medicine, Saga University, Saga (Japan); Ikeda, Satoshi [Department of Pathology and Microbiology, Faculty of Medicine, Saga University, Saga (Japan); Takezawa, Toshiaki [Transgenic Animal Research Center, National Institute of Agrobiological Sciences, Ibaraki (Japan); Kishi, Tomoya [Department of Internal Medicine, Saga University, Saga (Japan); Makino, Junichi [Makino Clinic, Saga (Japan); Uchihashi, Kazuyoshi; Matsunobu, Aki [Department of Pathology and Microbiology, Faculty of Medicine, Saga University, Saga (Japan); Noguchi, Mitsuru [Department of Urology, Faculty of Medicine, Saga University, Saga (Japan); Sugihara, Hajime [Department of Physical Therapy, International University of Health and Welfare, Fukuoka (Japan); Toda, Shuji [Department of Pathology and Microbiology, Faculty of Medicine, Saga University, Saga (Japan)
2011-12-16
Highlights: Black-Right-Pointing-Pointer Late-onset peritoneal fibrosis leading to EPS remains to be elucidated. Black-Right-Pointing-Pointer Fluid streaming is a potent factor for peritoneal fibrosis in PD. Black-Right-Pointing-Pointer We focused on the prolonged effect of fluid streaming on mesothelial cell kinetics. Black-Right-Pointing-Pointer A history of fluid streaming exposure promoted mesothelial proliferative activity. Black-Right-Pointing-Pointer We have thus identified a potent new factor for late-onset peritoneal fibrosis. -- Abstract: Encapsulating peritoneal sclerosis (EPS) often develops after transfer to hemodialysis and transplantation. Both termination of peritoneal dialysis (PD) and transplantation-related factors are risks implicated in post-PD development of EPS, but the precise mechanism of this late-onset peritoneal fibrosis remains to be elucidated. We previously demonstrated that fluid flow stress induced mesothelial proliferation and epithelial-mesenchymal transition via mitogen-activated protein kinase (MAPK) signaling. Therefore, we speculated that the prolonged bioactive effect of fluid flow stress may affect mesothelial cell kinetics after cessation of fluid streaming. To investigate how long mesothelial cells stay under the bioactive effect brought on by fluid flow stress after removal of the stress, we initially cultured mesothelial cells under fluid flow stress and then cultured the cells under static conditions. Mesothelial cells exposed to fluid flow stress for a certain time showed significantly high proliferative activity compared with static conditions after stoppage of fluid streaming. The expression levels of protein phosphatase 2A, which dephosphorylates MAPK, in mesothelial cells changed with time and showed a biphasic pattern that was dependent on the duration of exposure to fluid flow stress. There were no differences in the fluid flow stress-related bioactive effects on mesothelial cells once a certain time had passed
Spatial and temporal resolution of fluid flows: LDRD final report
Tieszen, S.R.; O`Hern, T.J.; Schefer, R.W.; Perea, L.D.
1998-02-01
This report describes a Laboratory Directed Research and Development (LDRD) activity to develop a diagnostic technique for simultaneous temporal and spatial resolution of fluid flows. The goal is to obtain two orders of magnitude resolution in two spatial dimensions and time simultaneously. The approach used in this study is to scale up Particle Image Velocimetry (PIV) and Planar Laser Induced Fluorescence (PLIF) to acquire meter-size images at up to 200 frames/sec. Experiments were conducted in buoyant, fully turbulent, non-reacting and reacting plumes with a base diameter of one meter. The PIV results were successful in the ambient gas for all flows, and in the plume for non-reacting helium and reacting methane, but not reacting hydrogen. No PIV was obtained in the hot combustion product region as the seed particles chosen vaporized. Weak signals prevented PLIF in the helium. However, in reacting methane flows, PLIF images speculated to be from Poly-Aromatic-Hydrocarbons were obtained which mark the flame sheets. The results were unexpected and very insightful. A natural fluorescence from the seed particle vapor was also noted in the hydrogen tests.
Wu, Binxin
2010-12-01
In this paper, 12 turbulence models for single-phase non-newtonian fluid flow in a pipe are evaluated by comparing the frictional pressure drops obtained from computational fluid dynamics (CFD) with those from three friction factor correlations. The turbulence models studied are (1) three high-Reynolds-number k-ε models, (2) six low-Reynolds-number k-ε models, (3) two k-ω models, and (4) the Reynolds stress model. The simulation results indicate that the Chang-Hsieh-Chen version of the low-Reynolds-number k-ε model performs better than the other models in predicting the frictional pressure drops while the standard k-ω model has an acceptable accuracy and a low computing cost. In the model applications, CFD simulation of mixing in a full-scale anaerobic digester with pumped circulation is performed to propose an improvement in the effective mixing standards recommended by the U.S. EPA based on the effect of rheology on the flow fields. Characterization of the velocity gradient is conducted to quantify the growth or breakage of an assumed floc size. Placement of two discharge nozzles in the digester is analyzed to show that spacing two nozzles 180° apart with each one discharging at an angle of 45° off the wall is the most efficient. Moreover, the similarity rules of geometry and mixing energy are checked for scaling up the digester.
Controlling Subsurface Fractures and Fluid Flow: A Basic Research Agenda
Pyrak-Nolte, Laura J [Purdue Univ., West Lafayette, IN (United States); DePaolo, Donald J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Univ. of California, Berkeley, CA (United States); Pietraß, Tanja [USDOE Office of Science, Washington, DC (United States)
2015-05-22
From beneath the surface of the earth, we currently obtain about 80-percent of the energy our nation consumes each year. In the future we have the potential to generate billions of watts of electrical power from clean, green, geothermal energy sources. Our planet’s subsurface can also serve as a reservoir for storing energy produced from intermittent sources such as wind and solar, and it could provide safe, long-term storage of excess carbon dioxide, energy waste products and other hazardous materials. However, it is impossible to underestimate the complexities of the subsurface world. These complexities challenge our ability to acquire the scientific knowledge needed for the efficient and safe exploitation of its resources. To more effectively harness subsurface resources while mitigating the impacts of developing and using these resources, the U.S. Department of Energy established SubTER – the Subsurface Technology and Engineering RD&D Crosscut team. This DOE multi-office team engaged scientists and engineers from the national laboratories to assess and make recommendations for improving energy-related subsurface engineering. The SubTER team produced a plan with the overall objective of “adaptive control of subsurface fractures and fluid flow.”This plan revolved around four core technological pillars—Intelligent Wellbore Systems that sustain the integrity of the wellbore environment; Subsurface Stress and Induced Seismicity programs that guide and optimize sustainable energy strategies while reducing the risks associated with subsurface injections; Permeability Manipulation studies that improve methods of enhancing, impeding and eliminating fluid flow; and New Subsurface Signals that transform our ability to see into and characterize subsurface systems. The SubTER team developed an extensive R&D plan for advancing technologies within these four core pillars and also identified several areas where new technologies would require additional basic research
THE FLOW PROBLEM OF FLUIDS FLOW IN A FRACTAL RESERVOIR WITH DOUBLE POROSITY
同登科; 张鸿庆
2001-01-01
The effective radius of oil well is introduced in the inner boundary in the problem of fluids flow through fractal reservoir with double porosity, and thus a new model is established. Taking the wellbore storage and steady-state skin effect into consideration, the exact solutions of the pressure distribution of fluids flow in fractal reservoirs with double porosity are given for the cases of an infinite outer boundary, a finite closed outer boundary and a bounded domain with the constant pressure outer boundary conditions. The pressure behavior of fractal reservoir with double porosity is analyzed by using a numerical inversion of the Laplace transform solution. The pressure responses of changing various parameters are discussed.
Lei, Hongwu; Li, Jun; Li, Xiaochun; Jiang, Zhenjiao
2016-09-01
Understanding the non-isothermal multiphase and multicomponent flow in a CO2-H2S-CH4-brine system is of critical importance in projects such as CO2 storage in deep saline aquifers, natural gas extraction using CO2 as the displacement fluid, and heat extraction from hot dry rocks using CO2 as the working fluid. Numerical simulation is a necessary tool to evaluate the chemical evolution in these systems. However, an accurate thermodynamic model for CO2-H2S-CH4-brine systems appropriate for high pressure, temperature, and salinity is still lacking. This study establishes the mutual solubility model for CO2-H2S-CH4-brine systems based on the fugacity-activity method for phase equilibrium. The model can predict mutual solubilities for pressure up to 1000 bar for CO2 and CH4, and 200 bar for H2S, for temperature up to 200 °C, and for salinity up to 6 mol/kg water. We incorporated the new model into TOUGH2/EOS7C, forming a new improved module we call EOS7Cm. Compared to the original EOS7C, EOS7Cm considers the effects of H2S and covers a larger range of temperature and salinity. EOS7Cm is employed in five examples, including CO2 injection with and without impurities (CH4 and/or H2S) into deep aquifers, CH4 extraction from aquifers by CO2 injection, and heat extraction from hot dry rock. The results are compared to those from TOUGH2/ECO2N, EOS7C and CMG, agreement among which serves to verify EOS7Cm.
Experimental stand for investigation of fluid flow in heat exchangers with cross-flow arrangement
Łopata Stanisław
2017-01-01
Full Text Available The operation analysis of high-performance heat exchanger with tubes elliptical indicated that the heat exchangers can be subject to damage. The reason for this is probably improper distribution of working fluid in tubular space of heat exchanger. Therefore, a part of the tubes may be improperly cooled and subject to compressible stresses. The paper presents an experimental stand allowing to confirm the given assumption. The experimental investigation enables to examine the mass flow rate in heat exchanger tubes. Also, it is possible to assess the impact of the construction of inlet, intermediate and outlet chambers on the flow distribution within the heat exchanger tubes.
Biosensor Arrays for Estimating Molecular Concentration in Fluid Flows
Abolfath-Beygi, Maryam
2011-01-01
This paper constructs dynamical models and estimation algorithms for the concentration of target molecules in a fluid flow using an array of novel biosensors. Each biosensor is constructed out of protein molecules embedded in a synthetic cell membrane. The concentration evolves according to an advection-diffusion partial differential equation which is coupled with chemical reaction equations on the biosensor surface. By using averaging theory methods and the divergence theorem, an approximate model is constructed that describes the asymptotic behaviour of the concentration as a system of ordinary differential equations. The estimate of target molecules is then obtained by solving a nonlinear least squares problem. It is shown that the estimator is strongly consistent and asymptotically normal. An explicit expression is obtained for the asymptotic variance of the estimation error. As an example, the results are illustrated for a novel biosensor built out of protein molecules.
Fluid-plasma interaction in compressible unstable flows
Massa, Luca
2014-11-01
The receptivity of the boundary layer discrete modes to dielectric barrier discharge (DBD) actuation is studied to improve the understanding of the interaction between non-equilibrium plasma and fluid in convectively amplified vortical layers. The momentum transfer induced by a DBD patch at various Reynolds numbers is evaluated using an adaptive mesh refinement computational solver in the Mach number regime 0.8-2.0. The energy of the induced modal perturbation is determined by weighting such a source term with the corresponding adjoint eigenfunctions. Conditions of maximum overlapping between the adjoint and the source term define the regimes of maximum receptivity and the locations of optimal placement of the DBD patch at different Mach and Reynolds numbers. The interaction between non-equilibrium plasma and the jet in cross flow is also being studied to determine the ability of DBD patches to influence mixing in the compressible regime, thus improving flame-holding in plasma assisted ignition and combustion.
Analytical methods for heat transfer and fluid flow problems
Weigand, Bernhard
2015-01-01
This book describes useful analytical methods by applying them to real-world problems rather than solving the usual over-simplified classroom problems. The book demonstrates the applicability of analytical methods even for complex problems and guides the reader to a more intuitive understanding of approaches and solutions. Although the solution of Partial Differential Equations by numerical methods is the standard practice in industries, analytical methods are still important for the critical assessment of results derived from advanced computer simulations and the improvement of the underlying numerical techniques. Literature devoted to analytical methods, however, often focuses on theoretical and mathematical aspects and is therefore useless to most engineers. Analytical Methods for Heat Transfer and Fluid Flow Problems addresses engineers and engineering students. The second edition has been updated, the chapters on non-linear problems and on axial heat conduction problems were extended. And worked out exam...
THE HEAT AND FLUID FLOW ANALYSIS FOR WATER HEATER
Chien-Nan Lin
2011-01-01
Full Text Available In this paper, the heat transfer and fluid flow are studied for the water heater of RV cars, in which the hot water is heated by the combustion energy of liquefied petroleum gases. Three types of combustion tubes are performed in this investigation, which are circular tube, elliptic tube and elliptic tube with screwed wire inserted. The heat transfer performances of numerical simulation results are compared with those of the experimental works; they are in good trend agreement. The elliptic combustion tube performs better than the circular one, which indicates the average 7% energy saving for the elliptic combustion tube and 12% energy saving for the elliptic combustion tube with screwed wire under static heating.
The transient behavior of electrorheological fluid in tensile flow
Tian, Yu; Zhang, Minliang; Zhu, Xuli; Jiang, Jile; Meng, Yonggang; Wen, Shizhu
2009-12-01
Transient behaviors of (ER) fluids in tensile flow and applied stepwise voltages were experimentally studied. The transient tensile stress rises exponentially with time. The characteristic rising time of tensile stress is independent of the amplitude of the applied voltage and the tensile velocity, while the amplitude of tensile yield stress is significantly affected by the two factors. The transient tension applied as a stepwise voltage is different from a stable tension pre-applied at constant voltage in different particle chain structure forming processes. Because of the chain aggregation during an intermittent voltage on-off test, the achieved tensile yield stress showed an exponent of 2.75 to the applied electric field at low separation velocities (0.2 mm s-1), higher than the square relationship predicted by traditional polarization models, and the exponent of 1.5 predicted by the conduction model. The results achieved in this study show that the mechanical properties of ER fluids are greatly affected by the method of applying the electric field, the strain rate, and the gap geometry between electrodes. These factors should be properly considered in the design and control of ER actuators.
A two-fluid model for violent aerated flows
Dias, Frédéric; Ghidaglia, Jean-Michel
2008-01-01
In the study of ocean wave impact on structures, one often uses Froude scaling since the dominant force is gravity. However the presence of trapped or entrained air in the water can significantly modify wave impacts. When air is entrained in water in the form of small bubbles, the acoustic properties in the water change dramatically. While some work has been done to study small-amplitude disturbances in such mixtures, little work has been done on large disturbances in air-water mixtures. We propose a basic two-fluid model in which both fluids share the same velocities and analyze some of its properties. It is shown that this model can successfully mimic water wave impacts on coastal structures. The governing equations are discretized by a second-order finite volume method. Numerical results are presented for two examples: the dam break problem and the drop test problem. It is shown that this basic model can be used to study violent aerated flows, especially by providing fast qualitative estimates.
Studies of Tracer Dispersion and Fluid Flow in Porous Media
Rage, T.
1996-12-31
This doctoral thesis explores the connection between the topology of a porous medium and its macroscopic transport properties and is based on computerized simulation. In porous media, both diffusion and convection contribute to the dispersion of a tracer and their combined effect is emphasized. The governing equations are solved numerically, using finite differences and Monte Carlo technique. The influence of finite Reynolds number on the outcome of echo-experiments is discussed. Comparing experiments and simulations it is found that nonlinear inertial forces lead to a visible deformation of a returned tracer at surprisingly small Reynolds numbers. In a study of tracer dispersion and fluid flow in periodic arrays of discs it is demonstrated that the mechanisms of mechanical dispersion in periodic media and in natural (non-periodic) porous media are essentially different. Measurements of the percolation probability distribution of a sandstone sample is presented. Local porosity theory predicts that this simple geometric function of a porous medium is of dominant importance for its macroscopic transport properties. It is demonstrated that many aspects of transport through fractures can be studied by using simple but realistic models and readily available computer resources. An example may be the transport of hydrocarbon fluids from the source rock to a reservoir. 165 refs., 44 figs., 1 table
Flow Field of Metallic Fluid Acted by Electromagnetic and Centrifugal Force
QIU Yi-qing; LUO Zong-an; JIA Guang-lin; LIU Xiang-hua; WANG Guo-dong
2004-01-01
According to the principle of electromagnetism and hydrodynamics, a mathematical model of flow field for metallic fluid acted by electromagnetic and centrifugal forces was established. The calculation results showed that the relative velocity between metallic fluid layers rises and the absolute rotational velocity of metallic fluid falls with the increase of magnetic induction intensity. The increase of centrifugal revolution hardly affects the relative velocity between metallic fluid layers, but can enhance the absolute rotational velocity of metallic fluid.
Pennell, Thomas; Yi, Juneyoung L; Kaufman, Bruce A; Krishnamurthy, Satish
2016-03-01
OBJECT Mechanical failure-which is the primary cause of CSF shunt malfunction-is not readily diagnosed, and the specific reasons for mechanical failure are not easily discerned. Prior attempts to measure CSF flow noninvasively have lacked the ability to either quantitatively or qualitatively obtain data. To address these needs, this preliminary study evaluates an ultrasonic transit time flow sensor in pediatric and adult patients with external ventricular drains (EVDs). One goal was to confirm the stated accuracy of the sensor in a clinical setting. A second goal was to observe the sensor's capability to record real-time continuous CSF flow. The final goal was to observe recordings during instances of flow blockage or lack of flow in order to determine the sensor's ability to identify these changes. METHODS A total of 5 pediatric and 11 adult patients who had received EVDs for the treatment of hydrocephalus were studied in a hospital setting. The primary EVD was connected to a secondary study EVD that contained a fluid-filled pressure transducer and an in-line transit time flow sensor. Comparisons were made between the weight of the drainage bag and the flow measured via the sensor in order to confirm its accuracy. Data from the pressure transducer and the flow sensor were recorded continuously at 100 Hz for a period of 24 hours by a data acquisition system, while the hourly CSF flow into the drip chamber was recorded manually. Changes in the patient's neurological status and their time points were noted. RESULTS The flow sensor demonstrated a proven accuracy of ± 15% or ± 2 ml/hr. The flow sensor allowed real-time continuous flow waveform data recordings. Dynamic analysis of CSF flow waveforms allowed the calculation of the pressure-volume index. Lastly, the sensor was able to diagnose a blocked catheter and distinguish between the blockage and lack of flow. CONCLUSIONS The Transonic flow sensor accurately measures CSF output within ± 15% or ± 2 ml
NUMERICAL ANALYSIS OF FLUID FLOW AND ADDED MASS INDUCED BY VIBRATION OF STRUCTURE
SU Li; LI Shu-juan; TANG Guo-an
2005-01-01
The fluid flow induced by light-density, low-stiffness structures was treated as inviscid, incompressible irrotational and steady plane flow. On the basis of the dipole configuration method, a singularity distribution method of distributing sources/sinks and dipoles on interfaces of the structure and fluid was developed to solve the problem of fluid flow induced by the vibration of common structures, such as columns and columns with fins,deduce the expression of kinetic energy of the fluid flow, and obtain the added mass finally.The calculational instances with analytical solutions prove the reliability of this method.
Souza Netto, Wilson F. de; Brito, Marcio F. P.; Dantas, Carlos C.; Silva, Jose Marcos F. da; Freitas, Romero B., E-mail: wilson.netto@ufpe.br, E-mail: jmfs5@yahoo.com.br, E-mail: romero.borgesf@gmail.com, E-mail: ccd@ufpe.br, E-mail: marciopaixaobrito@hotmail.com [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil); Santos, Valdemir A. dos, E-mail: vas@unicap.br [Universidade Catolica de Pernambuco (UNICAP), Recife, PE (Brazil). Dept. de Quimica; Barbosa, Enivaldo S., E-mail: enivaldo@dem.ufcg.edu.br [Universidade Federal de Campina Grande (UFCG), Campina Grande, PB (Brazil). Unidade Academica de Engenharia Mecanica
2013-07-01
An one-dimensional model was previously used to describe solid flow and operational conditions tests. By radial gamma ray profile a two-dimensional model was evaluated taken volumetric solid fraction as experimental parameters. Literature data provide a first test for solution of the two-dimensional model equations. Then, Axial and radial catalyst profiles were measured by gamma ray transmission in the riser of the Cold Flow Pilot Unit. For fluid flow, the mathematical model is established based on the equations of conservation of momentum and mass. However, in multicomponent flows, one should have a correction factor in these equations taking into account the influence of each component in the flow. This factor is the volumetric fraction of each component. The volumetric fraction of solids was obtained by measuring the pressure profile and calculating the solids specific mass relative to riser volume. With the technique of gamma transmission radiation could be measured in one single point of the riser, direct measurement, then several points to get a more precise axial profile and better definition. The data obtained were used as parameters for the differential equations of fluid dynamic model and MATLAB solved. (author)
Grabski, Jakub Krzysztof; Kołodziej, Jan Adam
2016-06-01
In the paper an analysis of fluid flow and heat transfer of a power-law fluid in an internally finned tube with different fin length is conducted. Nonlinear momentum equation of a power-law fluid flow and nonlinear energy equation are solved using the Picard iteration method. Then on each iteration step the solution of inhomogeneous equation consists of two parts: the general solution and the particular solution. Firstly the particular solution is obtained by interpolation of the inhomogeneous term by means of the radial basis functions and monomials. Then the general solution is obtained using the method of fundamental solutions and by fulfilling boundary conditions.
Effect of asynchrony on numerical simulations of fluid flow phenomena
Konduri, Aditya; Mahoney, Bryan; Donzis, Diego
2015-11-01
Designing scalable CFD codes on massively parallel computers is a challenge. This is mainly due to the large number of communications between processing elements (PEs) and their synchronization, leading to idling of PEs. Indeed, communication will likely be the bottleneck in the scalability of codes on Exascale machines. Our recent work on asynchronous computing for PDEs based on finite-differences has shown that it is possible to relax synchronization between PEs at a mathematical level. Computations then proceed regardless of the status of communication, reducing the idle time of PEs and improving the scalability. However, accuracy of the schemes is greatly affected. We have proposed asynchrony-tolerant (AT) schemes to address this issue. In this work, we study the effect of asynchrony on the solution of fluid flow problems using standard and AT schemes. We show that asynchrony creates additional scales with low energy content. The specific wavenumbers affected can be shown to be due to two distinct effects: the randomness in the arrival of messages and the corresponding switching between schemes. Understanding these errors allow us to effectively control them, rendering the method's feasibility in solving turbulent flows at realistic conditions on future computing systems.
Fluid Flow Simulation and Energetic Analysis of Anomalocarididae Locomotion
Mikel-Stites, Maxwell; Staples, Anne
2014-11-01
While an abundance of animal locomotion simulations have been performed modeling the motions of living arthropods and aquatic animals, little quantitative simulation and reconstruction of gait parameters has been done to model the locomotion of extinct animals, many of which bear little physical resemblance to their modern descendants. To that end, this project seeks to analyze potential swimming patterns used by the anomalocaridid family, (specifically Anomalocaris canadensis, a Cambrian Era aquatic predator), and determine the most probable modes of movement. This will serve to either verify or cast into question the current assumed movement patterns and properties of these animals and create a bridge between similar flexible-bodied swimmers and their robotic counterparts. This will be accomplished by particle-based fluid flow simulations of the flow around the fins of the animal, as well as an energy analysis of a variety of sample gaits. The energy analysis will then be compared to the extant information regarding speed/energy use curves in an attempt to determine which modes of swimming were most energy efficient for a given range of speeds. These results will provide a better understanding of how these long-extinct animals moved, possibly allowing an improved understanding of their behavioral patterns, and may also lead to a novel potential platform for bio-inspired underwater autonomous vehicles (UAVs).
唐力君; 劳昌玲; 范凡; 王健; 王广
2015-01-01
Both in-site real-time fluid analysis and off-site drilling mud analysis were used to detect the multi-components in the depth of drill hole WFSD and the profiles of multi-components in the drilling mud and other media during drilling. Through the comparison of fluid profile in the depth of the drill hole, the underground fluid geochemistry was discussed in the paper. The fluid from deep underground would be kept in the cycling mud during the drilling process. The further study of drilling mud gas, liquid and solid samples would be helpful to the determination of invasion of underground fluids in various ways. At the same time, the real-time fluid analysis during drilling would record the distinct signal change of components in the cycling mud. The lithologic variation of drilling core would easily cause the change of drilling mud gas, especially the change of multi-components in drilling mud gas. The lithologic section of relatively abundant fissures in the drill hole is the interval of greater drilling mud gas change. The indistinct correlation between multi-components of drilling mud gas and lithology of drilling core was comparatively studied, and the result could indicate the exact region and period in which the correlation of drilling fluid and aftershock was stronger, and this could be helpful to achieving the real degree of correlation between drilling fluid and aftershock.%采用场内钻探流体实时分析和场外钻探泥浆分析的方法，获得汶川地震断裂带科学钻探工程4号钻孔(WFSD-4)中深部井段流体多组分分析结果。研究钻孔深部井段的流体剖面地球化学特征，认为来自地下深部流体在钻探过程中会保存在钻探循环泥浆中，随钻流体实时分析可记录明显的组分变化信号。钻孔岩心的岩性变化易引起钻探泥浆气体的变化，特别是钻探泥浆气体中的多组分变化，在钻孔岩性裂隙较为丰富的井段，是钻探泥浆气体组分变化强度
Faizan-Ur-Rab, M.; Zahiri, S. H.; Masood, S. H.; Jahedi, M.; Nagarajah, R.
2017-06-01
This study presents the validation of a developed three-dimensional multicomponent model for cold spray process using two particle image velocimetry (PIV) experiments. The k- ɛ type 3D model developed for spherical titanium particles was validated with the measured titanium particle velocity within a nitrogen and helium supersonic jet. The 3D model predicted lower values of particle velocity than the PIV experimental study that used irregularly shaped titanium particles. The results of the 3D model were consistent with the PIV experiment that used spherical titanium powder. The 3D model simulation of particle velocity within the helium and nitrogen jet was coupled with an estimation of titanium particle temperature. This was achieved with the consideration of the fact that cold spray particle temperature is difficult and expensive to measure due to considerably lower temperature of particles than thermal spray. The model predicted an interesting pattern of particle size distribution with respect to the location of impact with a concentration of finer particles close to the jet center. It is believed that the 3D model outcomes for particle velocity, temperature and location could be a useful tool to optimize system design, deposition process and mechanical properties of the additively manufactured cold spray structures.
Modeling study on fluid flow and inclusion motion in 6-strand bloom caster tundishes
Guanghua Wen; Lifeng Zhang; Ping Tang; Zhenjiang Su; Mingmei Zhu; Wuan Gu; Kewen Zhao
2004-01-01
The behavior of fluid flow and particle motion in a 6-strand bloom caster tundish was investigated by a water model and numerical simulation. Compared with a device without flow control, the tundish with flow control has an important effect on the fluid flow pattern and inclusion removal. It is revealed that by non-isothermal process, which is real production condition, the fluid flow in tundish shows a strong buoyancy pattem, which drives particles to move upwards. The particle removal was quantitatively studied by mathematical and physical simulations.
Analytical solutions for the flow of Carreau and Cross fluids in circular pipes and thin slits
Sochi, Taha
2015-01-01
In this paper, analytical expressions correlating the volumetric flow rate to the pressure drop are derived for the flow of Carreau and Cross fluids through straight rigid circular uniform pipes and long thin slits. The derivation is based on the application of Weissenberg-Rabinowitsch-Mooney-Schofield method to obtain flow solutions for generalized Newtonian fluids through pipes and our adaptation of this method to the flow through slits. The derived expressions are validated by comparing th...
Jordan, Amy
, moisture, and porosity after heating by 750W waste canisters, assuming hydrous mineral mass fractions from 0--10%. The formation of a three-phase heat pipe (with counter-circulation of vapor and brine) occurs as water vapor is driven away from the heat source, condenses, and flows back towards the heat source, leading to changes in porosity, permeability, temperature, saturation, and thermal conductivity of the backfill salt surrounding the waste canisters. Heat pipe formation depends on temperature, moisture availability and fluid mobility. In certain cases, dehydration of hydrous minerals provided sufficient additional moisture to push the system into a sustained heat pipe where simulations neglecting this process did not. A laboratory-scale experiment (˜1 m3) using granular salt was conducted to gain a better understanding of the complex coupled processes involved in liquid, vapor, and solid transport occurring around heated nuclear waste in crushed salt, which could be a mode of disposal for HGNW. The experiment was designed to study transport processes in the system that have not been satisfactorily quantified in prior work. Initial results from the experimental effort offer promising insights. (Abstract shortened by UMI.).
Interstitial fluid flow:simulation of mechanical environment of cells in the interosseous membrane
Wei Yao; Guang-Hong Ding
2011-01-01
In vitro experiments have shown that subtle fluid flow environment plays a significant role in living biological tissues,while there is no in vivo practical dynamical measurement of the interstitial fluid flow velocity. On the basis of a new finding that capillaries and collagen fibrils in the interosseous membrane form a parallel array,we set up a porous media model simulating the flow field with FLUENT software,studied the shear stress on interstitial cells' surface due to the interstitial fluid flow,and analyzed the effect of flow on protein space distribution around the cells. The numerical simulation results show that the parallel nature of capillaries could lead to directional interstitial fluid flow in the direction of capillaries. Interstitial fluid flow would induce shear stress on the membrane of interstitial cells,up to 30 Pa or so,which reaches or exceeds the threshold values of cells' biological response observed in vitro. Interstitial fluid flow would induce nonuniform spacial distribution of secretion protein of mast cells. Shear tress on cells could be affected by capillary parameters such as the distance between the adjacent capillaries,blood pressure and the permeability coefficient of capillary's wall. The interstitial pressure and the interstitial porosity could also affect the shear stress on cells. In conclusion,numerical simulation provides an effective way for in vivo dynamic interstitial velocity research,helps to set up the vivid subtle interstitial flow environment of cells,and is beneficial to understanding the physiological functions of interstitial fluid flow.
Mathematical modeling for laminar flow of power law fluid in porous media
Silva, Renato A.; Mesquita, Maximilian S. [Universidade Federal do Espirito Santo (UFES), Sao Mateus, ES (Brazil). Centro Universitario Norte do Espirito Santo. Dept. de Engenharias e Computacao
2010-07-01
In this paper, the macroscopic equations for laminar power-law fluid flow is obtained for a porous medium starting from traditional equations (Navier-Stokes). Then, the volume averaging is applied in traditional transport equations with the power-law fluid model. This procedure leads to macroscopic transport equations set for non-Newtonian fluid. (author)
Tsamopoulos, John; Fraggedakis, Dimitris; Dimakopoulos, Yiannis
2015-11-01
We study the flow of two immiscible, Newtonian fluids in a periodically constricted tube driven by a constant pressure gradient. Our Volume-of-Fluid algorithm is used to solve the governing equations. First the code is validated by comparing its predictions to previously reported results for stratified and pulsing flow. Then it is used to capture accurately all the significant topological changes that take place. Initially, the fluids have a core-annular arrangement, which is found to either remain the same or change to a different arrangement depending on the fluid properties, the pressure driving the flow or the flow geometry. The flow-patterns that appear are the core-annular, segmented, churn, spray and segregated flow. The predicted scalings near pinching of the core fluid concur with similarity predictions and earlier numerical results (Cohen et al. (1999)). Flow-pattern maps are constructed in terms of the Reynolds and Weber numbers. Our results provide deeper insights in the mechanism of the pattern transitions and are in agreement with previous studies on core-annular flow (Kouris & Tsamopoulos (2001 & 2002)), segmented flow (Lac & Sherwood (2009)) and churn flow (Bai et al. (1992)). GSRT of Greece through the program ``Excellence'' (Grant No. 1918, entitled ``FilCoMicrA'').
Abolhasani, Milad
Flowing trains of uniformly sized bubbles/droplets (i.e., segmented flows) and the associated mass transfer enhancement over their single-phase counterparts have been studied extensively during the past fifty years. Although the scaling behaviour of segmented flow formation is increasingly well understood, the predictive adjustment of the desired flow characteristics that influence the mixing and residence times, remains a challenge. Currently, a time consuming, slow and often inconsistent manual manipulation of experimental conditions is required to address this task. In my thesis, I have overcome the above-mentioned challenges and developed an experimental strategy that for the first time provided predictive control over segmented flows in a hands-off manner. A computer-controlled platform that consisted of a real-time image processing module within an integral controller, a silicon-based microreactor and automated fluid delivery technique was designed, implemented and validated. In a first part of my thesis I utilized this approach for the automated screening of physical mass transfer and solubility characteristics of carbon dioxide (CO2) in a physical solvent at a well-defined temperature and pressure and a throughput of 12 conditions per hour. Second, by applying the segmented flow approach to a recently discovered CO2 chemical absorbent, frustrated Lewis pairs (FLPs), I determined the thermodynamic characteristics of the CO2-FLP reaction. Finally, the segmented flow approach was employed for characterization and investigation of CO2-governed liquid-liquid phase separation process. The second part of my thesis utilized the segmented flow platform for the preparation and shape control of high quality colloidal nanomaterials (e.g., CdSe/CdS) via the automated control of residence times up to approximately 5 minutes. By introducing a novel oscillatory segmented flow concept, I was able to further extend the residence time limitation to 24 hours. A case study of a
Lacroix, Brice; Travé, Anna; Buatier, Martine; Labaume, Pierre
2013-04-01
During compressive events, deformation in sedimentary basins is mainly accommodated by thrust faults emplacement and related fold growth. In such a structure, thrust faults are generally rooted in the basement and may act as conduits or barriers for crustal fluid flow. However, most of recent studies suggest that fluid flow through such discontinuities is not so evident and depends on the structural levels of the thrust inside the fold-and-thrust belt. In order to constrain the paleofluid flow through the Jaca thrust-sheet-top basin (Paleogene southwest-Pyrenean fold-and-thrust belt) we focus our study on different thrust faults located at different structural levels. The microstructures observed in the different studied fault zones are similar and consist of pervasive cleavage, calcite shear and extension veins and late dilatation veins. In order to constrain the nature and the source of fluids involved in fluid-rock interactions in fault zones, a geochemical approach, based on oxygen and carbon stable isotopes and trace elements on calcite, was adopted on the different vein generations and host rocks. The results suggest a high complexity in the paleo-hydrological behaviors of thrust faults evidencing a fluid-flow compartmentalization of the basin. North of the Jaca basin, previous studies in the southern part of the Axial Zones showed the contribution of deep metamorphic water, probably derived from the Paleozoic basement, along along fault zones related the major Gavarnie thrust. Contrarily, in the northern part of the Jaca basin, we evidence the contribution of formation water during the Monte Perdido thrust fault activity. These data suggest a closed hydrological fluid system where distance of fluid flow did not exceeded 70 m. On the other hand, the Jaca and Cotiella thrust faults, both located more to the south in the basin, are characterized by a composite fluid flow system. Indeed, stable isotopes and trace elements compositions of the first generation of
Heat Transfer and Fluid Flow of Nanofluids in Laminar Radial Flow Cooling Systems
Gilles ROY; Samy Joseph PALM; Cong Tam NGUYEN
2005-01-01
Nanofluids are considered as interesting alternatives to conventional coolants. It is well known that traditional fluids have limited heat transfer capabilities when compared to common metals. It is therefore quite conceivable that a small amount of extremely fine metallic particles placed in suspension in traditional fluids will considerably increase their heat transfer performances. A numerical investigation into the heat transfer enhancement capabilities of coolants with suspended metallic nanoparticles inside a radial, laminar flow cooling configuration is presented. Temperature dependant nanofluid properties are evaluated from experimental data available in recent literature. Results indicate that considerable heat transfer increases are possible with the use of relatively small volume fractions of nanoparticles. Generally, however, these are accompanied by considerable increases in wall shear-stress. Results also show that predictions obtained with temperature variable nanofluid properties yield greater heat transfer capabilities and lower wall shear stresses when compared to predictions using constant properties.
Free surface flow of a suspension of rigid particles in a non-Newtonian fluid
Svec, Oldrich; Skocek, Jan; Stang, Henrik
2012-01-01
A numerical framework capable of predicting the free surface flow of a suspension of rigid particles in a non-Newtonian fluid is described. The framework is a combination of the lattice Boltzmann method for fluid flow, the mass tracking algorithm for free surface representation, the immersed...
Space-time discontinuous Galerkin finite element method for two-fluid flows
Sollie, Warnerius Egbert Hendrikus
2010-01-01
The aim of this research project was to develop a discontinuous Galerkin method for two-fluid flows, which is accurate, versatile and can alleviate some of the problems commonly encountered with existing methods. A novel numerical method for two-fluid flow computations is presented, which combines t
A New Numerical Solution of Fluid Flow in Stratigraphic Porous Media
XU You-Sheng; LI Hua-Mei; GUO Shang-Ping; HUANG Guo-Xiang
2004-01-01
A new numerical technique based on a lattice-Boltzmann method is presented for analyzing the fluid flow in stratigraphic porous media near the earth's surface. The results obtained for the relations between porosity, pressure,and velocity satisfy well the requirements of stratigraphic statistics and hence are helpful for a further study of the evolution of fluid flow in stratigraphic media.
A physical five-equation model for compressible two-fluid flow, and its numerical treatment
Kreeft, J.J.; Koren, B.
2009-01-01
A novel five-equation model for inviscid, non-heat-conducting, compressible two-fluid flow is derived, together with an appropriate numerical method. The model uses flow equations based on conservation laws and exchange laws only. The two fluids exchange momentum and energy, for which source terms a
On specific features of investigation of fluid flows by photometric techniques
Vologdin, V. A.; Davydov, V. V.; Velichko, E. N.
2016-08-01
Specific features of investigation of the fluid flow structure in a pipeline by photometric techniques are considered. The applicability of the photometric techniques based on the Doppler effect to such studies is discussed. A new method for detecting defects on inner walls of a pipeline that involves the use of the laser radiation scattered from particles in a flowing fluid is suggested.
Tutorial on Feedback Control of Flows, Part I: Stabilization of Fluid Flows in Channels and Pipes
Ole M. Aamo
2002-07-01
Full Text Available The field of flow control has picked up pace over the past decade or so, on the promise of real-time distributed control on turbulent scales being realizable in the near future. This promise is due to the micromachining technology that emerged in the 1980s and developed at an amazing speed through the 1990s. In lab experiments, so called micro-electro-mechanical systems (MEMS that incorporate the entire detection-decision-actuation process on a single chip, have been batch processed in large numbers and assembled into flexible skins for gluing onto body-fluid interfaces for drag reduction purposes. Control of fluid flows span a wide variety of specialities. In Part I of this tutorial, we focus on the problem of reducing drag in channel and pipe flows by stabilizing the parabolic equilibrium profile using boundary feedback control. The control strategics used for this problem include classical control, based on the Nyquist criteria, and various optimal control techniques (H2, H-Infinity, as well as applications of Lyapunov stability theory.
A simple and rapid one-step continuous-flow synthesis route has been developed for the preparation of chromene derivatives from the reaction of aromatic aldehydes, α-cyanomethylene compounds and naphthols. In this contribution, a one-step continuous-flow protocol in a continuous ...
Advanced Fluid Reduced Order Models for Compressible Flow.
Tezaur, Irina Kalashnikova; Fike, Jeffrey A.; Carlberg, Kevin Thomas; Barone, Matthew F.; Maddix, Danielle; Mussoni, Erin E.; Balajewicz, Maciej (UIUC)
2017-09-01
This report summarizes fiscal year (FY) 2017 progress towards developing and implementing within the SPARC in-house finite volume flow solver advanced fluid reduced order models (ROMs) for compressible captive-carriage flow problems of interest to Sandia National Laboratories for the design and qualification of nuclear weapons components. The proposed projection-based model order reduction (MOR) approach, known as the Proper Orthogonal Decomposition (POD)/Least- Squares Petrov-Galerkin (LSPG) method, can substantially reduce the CPU-time requirement for these simulations, thereby enabling advanced analyses such as uncertainty quantification and de- sign optimization. Following a description of the project objectives and FY17 targets, we overview briefly the POD/LSPG approach to model reduction implemented within SPARC . We then study the viability of these ROMs for long-time predictive simulations in the context of a two-dimensional viscous laminar cavity problem, and describe some FY17 enhancements to the proposed model reduction methodology that led to ROMs with improved predictive capabilities. Also described in this report are some FY17 efforts pursued in parallel to the primary objective of determining whether the ROMs in SPARC are viable for the targeted application. These include the implemen- tation and verification of some higher-order finite volume discretization methods within SPARC (towards using the code to study the viability of ROMs on three-dimensional cavity problems) and a novel structure-preserving constrained POD/LSPG formulation that can improve the accuracy of projection-based reduced order models. We conclude the report by summarizing the key takeaways from our FY17 findings, and providing some perspectives for future work.
周义军; 蒲仁海; 强敏; 游佩林; 古兰军; 冯小敏
2012-01-01
To study the multicomponent seismic technique to enhance seismic prediction. Methods Based on detailed physical property analysis, the sensitive elastic properties for reservoir characterization is selected. The marking of PS data and matching of PP and PS data, the interpretation and joint inversion of PP and PS data is discussed. The PS AVO is thoroughly analyzed based on different types of wells. Results By combining the techniques of multicomponent seismic data, the success ratio has been increased more than 10% compared with P-wave seismic alone. Conclusion The accuracy of lithology and fluids prediction with multi-component seismic is effectively improved because PS data is available.%目的 探索利用多波分量技术提高地震储层测精度.方法 在精细岩石物理分析和岩性、流体敏感因子优选的基础上,通过PS波标定,纵横波精细对齐进行纵横波联合解释、联合反演;利用实测全波列测井数据对PS波AVO响应特征和储层及流体的关系进行定量研究.结果 在研究区进行含气性预测,预测符合率较单一纵波提高10％以上.结论 多波勘探技术因增加了横波信息,有效提高了岩性和流体预测精度.
Exact Solution of Unsteady Flow of Viscoelastic Fluid in a Pipe with Fractional Maxwell Model
无
2007-01-01
The unsteady flow of viscoelastic fluid in a cylindrical pipe was investigated using the fractional Maxwell model. Two special cases of unsteady pipe flow were expressed. The first is start-up flow, and the second is oscillating flow. The exact solution of start-up flow under a constant pressure gradient was obtained by using the theories of Laplace transform and Fourier-Bessel series for fractional derivatives. The exact solution of oscillating flow was obtained by utilizing the separation of variables.
Numerical Modeling of Porous Structure of Biomaterial and Fluid Flowing Through Biomaterial
无
2005-01-01
A Cellular Automata model of simulating body fluid flowing into porous bioceramic implants generated with stochastic methods is described, of which main parameters and evolvement rule are determined in terms of flow behavior of body fluid in porous biomaterials. The model is implemented by GUI( Graphical User Interface) program in MATLAB, and the results of numerical modeling show that the body fluid percolation is related to the size of pores and porosity.
Flow study in channel with the use computational fluid dynamics (CFD)
Oliveira, W. D.; Pires, M. S. G.; Canno, L. M.; Ribeiro, L. C. L. J.
2016-08-01
The Computational Fluid Dynamics (CFD) is a tool used to numerically simulate fluid flow behavior, and all the laws that govern the study of fluids is the mass transfer and energy, chemical reactions, hydraulic behaviors, among others applications. This tool mathematical equation solves the problem in a specific manner over a region of interest, with predetermined boundary conditions on this region. This work is to study the flow channel through the CFD technique.
Unsteady Boundary-Layer Flow over Jerked Plate Moving in a Free Stream of Viscoelastic Fluid
Sufian Munawar
2014-01-01
Full Text Available This study aims to investigate the unsteady boundary-layer flow of a viscoelastic non-Newtonian fluid over a flat surface. The plate is suddenly jerked to move with uniform velocity in a uniform stream of non-Newtonian fluid. Purely analytic solution to governing nonlinear equation is obtained. The solution is highly accurate and valid for all values of the dimensionless time 0≤τ<∞. Flow properties of the viscoelastic fluid are discussed through graphs.
Controlling Subsurface Fractures and Fluid Flow: A Basic Research Agenda
Pyrak-Nolte, Laura J [Purdue Univ., West Lafayette, IN (United States); DePaolo, Donald J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Univ. of California, Berkeley, CA (United States); Pietraß, Tanja [USDOE Office of Science, Washington, DC (United States)
2015-05-22
From beneath the surface of the earth, we currently obtain about 80-percent of the energy our nation consumes each year. In the future we have the potential to generate billions of watts of electrical power from clean, green, geothermal energy sources. Our planet’s subsurface can also serve as a reservoir for storing energy produced from intermittent sources such as wind and solar, and it could provide safe, long-term storage of excess carbon dioxide, energy waste products and other hazardous materials. However, it is impossible to underestimate the complexities of the subsurface world. These complexities challenge our ability to acquire the scientific knowledge needed for the efficient and safe exploitation of its resources. To more effectively harness subsurface resources while mitigating the impacts of developing and using these resources, the U.S. Department of Energy established SubTER – the Subsurface Technology and Engineering RD&D Crosscut team. This DOE multi-office team engaged scientists and engineers from the national laboratories to assess and make recommendations for improving energy-related subsurface engineering. The SubTER team produced a plan with the overall objective of “adaptive control of subsurface fractures and fluid flow.”This plan revolved around four core technological pillars—Intelligent Wellbore Systems that sustain the integrity of the wellbore environment; Subsurface Stress and Induced Seismicity programs that guide and optimize sustainable energy strategies while reducing the risks associated with subsurface injections; Permeability Manipulation studies that improve methods of enhancing, impeding and eliminating fluid flow; and New Subsurface Signals that transform our ability to see into and characterize subsurface systems. The SubTER team developed an extensive R&D plan for advancing technologies within these four core pillars and also identified several areas where new technologies would require additional basic research
Mathematical Model of Fluid Flow and Solidification in Mold Region of Continuous Slab Casting
谭利坚; 沈厚发; 柳百成
2003-01-01
To simulate the phenomena in the mold region of continuous casting by coupling fluid flow and solidification, a three-dimensional mathematical model has been developedbased on the K-ε turbulence equations and the SIMPLER algorithm. A pseudo source term was introduced into the energy equation to account for the latent heat and kinetic energy. The fluid flow in the mushy zone was calculated by defining the fluid viscosity as a function of the solid fraction in the mushy zone. Fine meshes in the solid region improve convergence and reduce iteration time. Comparison of the fluid flow and temperature distribution with and without solidification shows that although the solid shell in the mold is thin, it still greatly affects the flow pattern. The numerical results obtained provide details of the fluid flow and solidification phenomena which can be used to optimize the nozzle structure and other process parameters in continuous casting.
Heat transfer and fluid flow in biological processes advances and applications
Becker, Sid
2015-01-01
Heat Transfer and Fluid Flow in Biological Processes covers emerging areas in fluid flow and heat transfer relevant to biosystems and medical technology. This book uses an interdisciplinary approach to provide a comprehensive prospective on biofluid mechanics and heat transfer advances and includes reviews of the most recent methods in modeling of flows in biological media, such as CFD. Written by internationally recognized researchers in the field, each chapter provides a strong introductory section that is useful to both readers currently in the field and readers interested in learning more about these areas. Heat Transfer and Fluid Flow in Biological Processes is an indispensable reference for professors, graduate students, professionals, and clinical researchers in the fields of biology, biomedical engineering, chemistry and medicine working on applications of fluid flow, heat transfer, and transport phenomena in biomedical technology. Provides a wide range of biological and clinical applications of fluid...
Separation mechanisms and fluid flow in oil/water separation
Celius, H.K.; Knudsen, B. [IKU Petroleumsforskning A/S, Trondheim (Norway); Hafskjold, B.; Hansen, E.W. [Selskapet for Industriell og Teknisk Forskning, Trondheim (Norway)
1996-12-31
This paper describes work aimed at physical and numerical modeling of separation rates of oil/water systems in order to establish better tools for design and operation of offshore operators. This work aims to integrate the chemical and physical phenomena behind coalescence and settling with those of fluid flow in the system, in order to develop tools for design and operational analysis of separation equipment. The work includes the development of a high pressure, bench-scale test rig to perform separation tests on live oil and water samples, and a rationale in the form of a computer code that can be used to interpret the test results and transform them to a form siutable for operational purposes. This involves a formulation of a mathematical description of the chemical and physical mechanisms behind the emulsification and separation process, and to establish a link to the hydrdynamic properties of the separator vessel. The Emucol computer program is used in the analysis. 12 refs., 5 figs.
Sankar, D. S. [Universiti Teknologi Brunei, Bandar Seri Begawan (Brunei Darussalam); Lee, U Sik [Inha University, Incheon (Korea, Republic of)
2016-07-15
This theoretical study investigates three types of basic flows of viscous incompressible Herschel-Bulkley fluid such as (i) plane Couette flow, (ii) Poiseuille flow and (iii) generalized Couette flow with slip velocity at the boundary. The analytic solutions to the nonlinear boundary value problems have been obtained. The effects of various physical parameters on the velocity, flow rate, wall shear stress and frictional resistance to flow are analyzed through appropriate graphs. It is observed that in plane Poiseuille flow and generalized Couette flow, the velocity and flow rate of the fluid increase considerably with the increase of the slip parameter, power law index, pressure gradient. The fluid velocity is significantly higher in plane Poiseuille flow than in plane Couette flow. The wall shear stress and frictional resistance to flow decrease considerably with the increase of the power law index and increase significantly with the increase of the yield stress of the fluid. The wall shear stress and frictional resistance to flow are considerably higher in plane Poiseuille flow than in generalized Couette flow.
Boundary layer flow and heat transfer to Carreau fluid over a nonlinear stretching sheet
Masood Khan; Hashim
2015-01-01
This article studies the Carreau viscosity model (which is a generalized Newtonian model) and then use it to obtain a formulation for the boundary layer equations of the Carreau fluid. The boundary layer flow and heat transfer to a Carreau model over a nonlinear stretching surface is discussed. The Carreau model, adequate for many non-Newtonian fluids, is used to characterize the behavior of the fluids having shear thinning properties and fluids with shear thickening properties for numerical ...
Flow of a non-Newtonian fluid through channels with permeable wall
Martins-Costa, Maria Laura [Universidade Federal Fluminense, Niteroi, RJ (Brazil). Dept. de Engenharia Mecanica. Lab. de Matematica Teorica e Aplicada]. E-mail: laura@mec.uff.br; Gama, Rogerio M. Saldanha da [Laboratorio Nacional de Computacao Cientifica (LNCC), Petropolis, RJ (Brazil)]. E-mail: rsgama@domain.com.br; Frey, Sergio [Rio Grande do Sul Univ., Porto Alegre, RS (Brazil). Dept. de Engenharia Mecanica. Grupo de Estudos Termicos e Energeticos
2000-07-01
In the present work the momentum transport in two adjacent flow regions is described by means of a continuum theory of mixtures, specially developed to model multiphase phenomena. A generalized Newtonian fluid flows through the permeable wall channel, originating a pure fluid region and a mixture region - where the fluid saturates the porous matrix. The fluid and the porous matrix are treated as continuous constituents of a binary mixture coexisting superposed, each of them occupying simultaneously the whole volume of the mixture. An Ostwald-de Waele behavior is assumed for both the fluid constituent (in the mixture region) and the fluid (in the so-called pure fluid region), while the porous matrix, represented by the solid constituent, is assumed rigid, homogeneous, isotropic and at rest. Compatibility conditions at the interface (pure fluid-mixture) for momentum transfer are proposed and discussed. Assuming no flow across the interface, the velocity should be zero on the solid parts of the boundary and should match the fluid diffusing velocity on the fluid parts of the boundary. Also the shear stress at the pure fluid region is to be balanced by a multiple of the partial shear stress at the mixture region. A minimum principle for the above-described problem, assuming fully developed flow in both regions, is presented, providing an easy and reliable way for carrying out numerical simulations. (author)
Intermittent flow in yield-stress fluids slows down chaotic mixing.
Wendell, D M; Pigeonneau, F; Gouillart, E; Jop, P
2013-08-01
We present experimental results of chaotic mixing of Newtonian fluids and yield-stress fluids using a rod-stirring protocol with a rotating vessel. We show how the mixing of yield-stress fluids by chaotic advection is reduced compared to the mixing of Newtonian fluids and explain our results, bringing to light the relevant mechanisms: the presence of fluid that only flows intermittently, a phenomenon enhanced by the yield stress, and the importance of the peripheral region. This finding is confirmed via numerical simulations. Anomalously slow mixing is observed when the synchronization of different stirring elements leads to the repetition of slow stretching for the same fluid particles.
Numerical simulation of fluid flow in a reheating furnace with multi-swirling-burners
Baowei Li; Zengwu Zhao; Yike Li; Wenfei Wu; Daqiang Cang
2003-01-01
A general numerical simulating program for three-dimensional (3-D) and time-dependent fluid flow for a reheating furnace with multi-swirling-burners has been developed based upon an arbitrary Lagrangian-Eulerian scheme (ALE) with the finite volume method. The parameters of fluid flow in a reheating furnace with multi-swirling-burners was calculated and the 3-D velocity distributions were obtained. The design of the burners was optimized for forming better swirling flow. The simulation shows that the fluid flow in the reheating furnace with the optimized burners is reasonable.
Mohamad-Saleh, J.; Hoyle, B. S.
2002-12-01
Artificial neural networks (ANNs) have been used to investigate their capabilities at estimating key parameters for the characterization of flow processes, based on electrical capacitance-sensed tomographic (ECT) data. The estimations of the parameters are made directly, without recourse to tomographic images. The parameters of interest include component height and interface orientation of two-component flows, and component fractions of two-component and three-component flows. Separate multi-layer perceptron networks were trained with patterns consisting of pairs of simulated ECT data and the corresponding component heights, interface orientations and component fractions. The networks were then tested with patterns consisting of unlearned simulated ECT data of various flows and with real ECT data of gas-water flows. The neural systems provided estimations having mean absolute errors of less than 1% for oil and water heights and fractions and less than 10° for interface orientations. When tested with real plant ECT data, the mean absolute errors were less than 4% for water height, less than 15° for gas-water interface orientation and less than 3% for water fraction, respectively. The results demonstrate the feasibility of the application of ANNs for flow process parameter estimations based upon tomography data.
Sentman, L.H.; Nayfeh, M.H.
1983-12-01
This research is an integrated theoretical and experimental investigation of the nonlinear interactions which may occur between the chemical kinetics, the fluid dynamics and the unstable resonator of a continuous wave fluid flow laser. The objectives of this grant were to measure the frequency and amplitude of the time dependent pulsations in the power spectral output which have been predicted to occur in cw chemical lasers employing unstable resonators to extract power.
Simulation of horizontal pipe two-phase slug flows using the two-fluid model
Ortega Malca, Arturo J. [Pontificia Univ. Catolica do Rio de Janeiro, RJ (Brazil). Dept. de Engenharia Mecanica. Nucleo de Simulacao Termohidraulica de Dutos (SIMDUT); Nieckele, Angela O. [Pontificia Univ. Catolica do Rio de Janeiro, RJ (Brazil). Dept. de Engenharia Mecanica
2005-07-01
Slug flow occurs in many engineering applications, mainly in the transport of hydrocarbon fluids in pipelines. The intermittency of slug flow causes severe unsteady loading on the pipelines carrying the fluids, which gives rise to design problems. Therefore, it is important to be able to predict the onset and development of slug flow as well as slug characteristics. The present work consists in the simulation of two-phase flow in slug pattern through horizontal pipes using the two-fluid model in its transient and one-dimensional form. The advantage of this model is that the flow field is allowed to develop naturally from a given initial conditions as part of the transient calculation; the slug evolves automatically as a product of the computed flow development. Simulations are then carried out for a large number of flow conditions that lead a slug flow. (author)
Shuqing HAO; Hongwei HUANG; Kun YIN
2007-01-01
By simplifying the characters in the air reverse circulation bit interior fluid field, the authors used air dynamics and fluid mechanics to calculate the air distribution in the bit and obtained an equation of flow distribution with a unique resolution. This study will provide help for making certain the bit parameters of the bit structure effectively and study the air reverse circulation bit interior fluid field character deeply.
Exact solutions for MHD flow of couple stress fluid with heat transfer
Najeeb Alam Khan
2016-01-01
Full Text Available This paper aims at presenting exact solutions for MHD flow of couple stress fluid with heat transfer. The governing partial differential equations (PDEs for an incompressible MHD flow of couple stress fluid are reduced to ordinary differential equations by employing wave parameter. The methodology is implemented for linearizing the flow equations without extra transformation and restrictive assumptions. Comparison is made with the result obtained previously.
A Tightly Coupled Particle-Fluid Model for DNA-Laden Flows in Complex Microscale Geometries
Trebotich, D; Miller, G H; Colella, P; Graves, D T; Martin, D F; Schwartz, P O
2004-11-18
We present a stable and convergent method for the computation of flows of DNA-laden fluids in microchannels with complex geometry. The numerical strategy combines a ball-rod model representation for polymers tightly coupled with a projection method for incompressible viscous flow. We use Cartesian grid embedded boundary methods to discretize the fluid equations in the presence of complex domain boundaries. A sample calculation is presented showing flow through a packed array microchannel in 2D.
Simulating Cerebrospinal Fluid Flow and Spinal Cord Movement Associated with Syringomyelia
Vinje, Vegard
2016-01-01
Syringomyelia is a progressive disease where fluid filled cavities develop inside the spinal cord, and is frequently seen together with Chiari Malformation I (CMI). CMI is characterized by downwards displacements of the Cerebellar Tonsils obstructing flow in the Subarachnoid space, (SAS) which causes abnormal Cerebrospinal fluid (CSF) flow. Many theories on the pathogenesis of syringomyelia have been proposed, many related to abnormal CSF flow, but a full explanation has not yet been given. I...
Coupling Analysis of Fluid-Structure Interaction and Flow Erosion of Gas-Solid Flow in Elbow Pipe
Hongjun Zhu; Hongnan Zhao; Qian Pan; Xue Li
2014-01-01
A numerical simulation has been conducted to investigate flow erosion and pipe deformation of elbow in gas-solid two-phase flow. The motion of the continuous fluid phase is captured based on calculating three-dimensional Reynolds-averaged-Navier-Stokes (RANS) equations, while the kinematics and trajectory of the discrete particles are evaluated by discrete phase model (DPM), and a fluid-structure interaction (FSI) computational model is adopted to calculate the pipe deformation. The effects o...
Film Flow Dominated Simultaneous Flow of Two Viscous Incompressible Fluids Through a Porous Medium
Olav eAursjø
2014-11-01
Full Text Available We present an experimental study of two-phase flow in a quasi-two-dimensional porous medium. The two phases, a water-glycerol solution and a commercial food grade rapeseed/canola oil, having an oil to water-glycerol viscosity ratio of 1.3, are injected simultaneously into a Hele-Shaw cell with a mono-layer of randomly distributed glass beads. The two liquids are injected into the model from alternating point inlets. Initially, the porous model is filled with the water-glycerol solution. We observe that after an initial transient state, an overall static cluster configuration is obtained. While the oil is found to create a connected system spanning cluster, a large part of the water-glycerol clusters left behind the initial invasion front is observed to remain immobile throughout the rest of the experiment. This could suggest that the water-glycerol flow-dynamics is largely dominated by film flow. The flow pathways are thus given through the dynamics of the initial invasion. This behavior is quite different from that observed in systems with large viscosity differences between the two fluids, and where compressibility plays an important part of the process.
Fluid flow and mineralization of Youjiang Basin in the Yunnan-Guizhou-Guangxi area, China
王国芝; 胡瑞忠; 苏文超; 朱赖民
2003-01-01
Comprehensive studies, based on isotope geochemistry of C, H, O, S and Sr, chronology, common element and trace element geochemistry of fluid inclusions for the epithermal Au, As, Sb and Hg deposits in the Youjiang Basin and its peripheral areas, suggested that the ore fluid was the basin fluid with abundant metallic elements and the large-scale fluid flow of the same source in the late Yenshan stage was responsible for huge epithermal mineralization and silicification. The ore fluid flowed from the basin to the platform between the basin and the platform and migrated from the inter-platform basin to the isolated platform in the Youjiang Basin. The synsedimentary faults and paleokast surface acted respectively as main conduits for vertical and lateral fluid flow.
Distribution of flowing fluids in a confined porous medium under microgravity conditions
Guo, Boyun; Holder, Donald W.; Carter, Layne
2004-08-01
Predicting distribution of flowing fluids in confined porous media under microgravity conditions is vitally important for optimal design of packed bubble column reactors in space stations. Existing correlations have been found inaccurate when applied to microgravity conditions. On the basis of Darcy's law for two-phase flow, a simple mathematical model has been developed in this study. Sensitivity analyses with the model indicate that for a given combination of wetting and nonwetting fluid flow rates, fluid holdups are controlled by relative permeabilities. The effect of gravity on fluid holdup is influenced by the absolute permeability of the porous medium. Fluid distribution is affected by the temperature-dependent fluid properties and wall effect.
Predicting phase shift of elastic waves in pipes due to fluid flow and imperfections
Thomsen, Jon Juel; Dahl, Jonas; Fuglede, Niels
2009-01-01
Flexural vibrations of a fluid-conveying pipe is investigated, with special consideration to the spatial shift in phase caused by fluid flow and various imperfections, e.g., non-ideal supports, non-uniform stiffness or mass, non-proportional damping, weak nonlinearity, and flow pulsation. This is......Flexural vibrations of a fluid-conveying pipe is investigated, with special consideration to the spatial shift in phase caused by fluid flow and various imperfections, e.g., non-ideal supports, non-uniform stiffness or mass, non-proportional damping, weak nonlinearity, and flow pulsation....... This is relevant for understanding wave propagation in elastic media in general, and for the design and trouble-shooting of phase-shift measuring devices such as Coriolis mass flowmeters in particular. A multiple time scaling perturbation analysis is employed for a simple model of a fluid-conveying pipe...
Animation of interactive fluid flow visualization tools on a data parallel machine
Sethian, J.A. (California Univ., Berkeley, CA (USA). Dept. of Mathematics); Salem, J.B. (Thinking Machines Corp., Cambridge, MA (USA))
1989-01-01
The authors describe a new graphics environment for essentially real-time interactive visualization of computational fluid mechanics. The researcher may interactively examine fluid data on a graphics display using animated flow visualization diagnostics that mimic those in the experimental laboratory. These tools include display of moving color contours for scalar fields, smoke or dye injection of passive particles to identify coherent flow structures, and bubble wire tracers for velocity profiles, as well as three-dimensional interactive rotation and zoom and pan. The system is implemented on a data parallel supercomputer attached to a framebuffer. Since most fluid visualization techniques are highly parallel in nature, this allows rapid animation of fluid motion. The authors demonstrate our interactive graphics fluid flow system by analyzing data generated by numerical simulations of viscous, incompressible, laminar and turbulent flow over a backward-facing step and in a closed cavity. Input parameters are menu-driven, and images are updated at nine frames per second.
Chaos analysis of viscoelastic chaotic flows of polymeric fluids in a micro-channel
Lim, C. P.; Lam, Y. C., E-mail: myclam@ntu.edu.sg [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 639798 (Singapore); BioSystems and Micromechanics (BioSyM) IRG, Singapore-MIT Alliance for Research and Technology (SMART) Centre, 138602 (Singapore); Han, J. [BioSystems and Micromechanics (BioSyM) IRG, Singapore-MIT Alliance for Research and Technology (SMART) Centre, 138602 (Singapore); Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Department of Biological Engineering, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States)
2015-07-15
Many fluids, including biological fluids such as mucus and blood, are viscoelastic. Through the introduction of chaotic flows in a micro-channel and the construction of maps of characteristic chaos parameters, differences in viscoelastic properties of these fluids can be measured. This is demonstrated by creating viscoelastic chaotic flows induced in an H-shaped micro-channel through the steady infusion of a polymeric fluid of polyethylene oxide (PEO) and another immiscible fluid (silicone oil). A protocol for chaos analysis was established and demonstrated for the analysis of the chaotic flows generated by two polymeric fluids of different molecular weight but with similar relaxation times. The flows were shown to be chaotic through the computation of their correlation dimension (D{sub 2}) and the largest Lyapunov exponent (λ{sub 1}), with D{sub 2} being fractional and λ{sub 1} being positive. Contour maps of D{sub 2} and λ{sub 1} of the respective fluids in the operating space, which is defined by the combination of polymeric fluids and silicone oil flow rates, were constructed to represent the characteristic of the chaotic flows generated. It was observed that, albeit being similar, the fluids have generally distinct characteristic maps with some similar trends. The differences in the D{sub 2} and λ{sub 1} maps are indicative of the difference in the molecular weight of the polymers in the fluids because the driving force of the viscoelastic chaotic flows is of molecular origin. This approach in constructing the characteristic maps of chaos parameters can be employed as a diagnostic tool for biological fluids and, more generally, chaotic signals.
Chaos analysis of viscoelastic chaotic flows of polymeric fluids in a micro-channel
C. P. Lim
2015-07-01
Full Text Available Many fluids, including biological fluids such as mucus and blood, are viscoelastic. Through the introduction of chaotic flows in a micro-channel and the construction of maps of characteristic chaos parameters, differences in viscoelastic properties of these fluids can be measured. This is demonstrated by creating viscoelastic chaotic flows induced in an H-shaped micro-channel through the steady infusion of a polymeric fluid of polyethylene oxide (PEO and another immiscible fluid (silicone oil. A protocol for chaos analysis was established and demonstrated for the analysis of the chaotic flows generated by two polymeric fluids of different molecular weight but with similar relaxation times. The flows were shown to be chaotic through the computation of their correlation dimension (D2 and the largest Lyapunov exponent (λ1, with D2 being fractional and λ1 being positive. Contour maps of D2 and λ1 of the respective fluids in the operating space, which is defined by the combination of polymeric fluids and silicone oil flow rates, were constructed to represent the characteristic of the chaotic flows generated. It was observed that, albeit being similar, the fluids have generally distinct characteristic maps with some similar trends. The differences in the D2 and λ1 maps are indicative of the difference in the molecular weight of the polymers in the fluids because the driving force of the viscoelastic chaotic flows is of molecular origin. This approach in constructing the characteristic maps of chaos parameters can be employed as a diagnostic tool for biological fluids and, more generally, chaotic signals.
Homotopy perturbation method for heat transfer flow of a third grade fluid between parallel plates
Siddiqui, A.M. [Pennsylvania State University, York Campus, York, PA 17403 (United States); Zeb, A. [COMSATS Institute of Information Technology, 30 H-8/1, Islamabad (Pakistan)], E-mail: amtaz56@yahoo.co.uk; Ghori, Q.K. [COMSATS Institute of Information Technology, 30 H-8/1, Islamabad (Pakistan); Benharbit, A.M. [Pennsylvania State University, York Campus, York, PA 17403 (United States)
2008-04-15
The present paper studies the heat transfer flow of a third grade fluid between two heated parallel plates for the constant viscosity model. Three flow problems, namely plane Couette flow, plane Poiseuille flow and plane Couette-Poiseuille flow have been considered. In each case the non-linear momentum equation and the energy equation have been solved using the homotopy perturbation method. Explicit analytical expressions for the velocity field and the temperature distribution have been derived.
Some analytical solutions for flows of Casson fluid with slip boundary conditions
K. Ramesh
2015-09-01
Full Text Available In the present paper, we have studied three fundamental flows namely Couette, Poiseuille and generalized Couette flows of an incompressible Casson fluid between parallel plates using slip boundary conditions. The equations governing the flow of Casson fluid are non-linear in nature. Analytical solutions of the non-linear governing equations with non-linear boundary conditions are obtained for each case. The effect of the various parameters on the velocity and volume flow rate for each problem is studied and the results are presented through graphs. It is observed that, the presence of Casson number decreases the velocity and volume flow rate of the fluid. Increasing of slip parameter increases the velocity and volume flow rate in both Poiseuille and generalized Couette flows.
Chen, Yong; Huang, Yiyong; Chen, Xiaoqian
2013-02-01
Ultrasonic flow meter with non-invasive no-moving-parts construction has good prospective application for space on-orbit fluid gauging. In traditional pulse transit time flow meter, inconsistency of ultrasonic transducers leads to measurement error and plane wave theory, bases of transit time flow meter, is valuable only for low-frequency wave propagation in inviscid fluid and will lose feasibility when fluid viscosity is considered. In this paper, based on the hydrodynamics of viscous fluid, wave propagation with uniform flow profile is mathematically formulated and a novel solution for viscous fluid using potential theory is firstly presented. Then a novel design methodology of continuous ultrasonic flow meter is proposed, where high measurement rangeability and accuracy are guaranteed individually by solving the integral ambiguity using multi-tone wide laning strategy and the fractional phase shift using phase lock loop tracking method. A comparison with transit time ultrasonic flow meter shows the advantage of proposed methodology. In the end, parametric analysis of viscosity on wave propagation and ultrasonic flow meter is compressively investigated.
Weinstein, H.; Lavan, Z.
1975-01-01
Analytical investigations of fluid dynamics problems of relevance to the gaseous core nuclear reactor program are presented. The vortex type flow which appears in the nuclear light bulb concept is analyzed along with the fluid flow in the fuel inlet region for the coaxial flow gaseous core nuclear reactor concept. The development of numerical methods for the solution of the Navier-Stokes equations for appropriate geometries is extended to the case of rotating flows and almost completes the gas core program requirements in this area. The investigations demonstrate that the conceptual design of the coaxial flow reactor needs further development.
MHD Flow of an Oldroyd-B Fluid through a Porous Space Induced by Sawtooth Pulses
Masood Khan; Zeeshan
2011-01-01
@@ We investigate the unsteady magnetohydrodynamic (MHD) flow of an Oldroyd-B fluid through a porous space inducedby sawtooth pulses.The fluid is assumed to be electrically conducting in the presence of a transverse uniform magnetic field.The porous space is taken into account using modified Darcy's law for the Oldroyd-B fluid.Exact solutions of the governing problem are obtained by using the Laplace transform method.The effects of the magnetic parameter, the permeability of the porous space and the elasticity parameter of the fluid are studied on the flow characteristics.
Analysis of general second-order fluid flow in double cylinder rheometer
黄军旗; 何光渝; 刘慈群
1997-01-01
The fractional calculus approach in the constitutive relationship model of second-order fluid is introduced and the flow characteristics of the viscoelastic fluid in double cylinder rheometer are studied. First, the analytical solution of which the derivative order is 1/2 is derived with the analytical solution and the reliability of Laplace numerical inversion based on Crump algorithm for the problem is verified, then the characteristics of second-order fluid flow in the rheometer by using Crump method is analyzed. The results indicate that the more obvious the viscoelastic properties of fluid are, the more sensitive the dependence of velocity and stress on fractional derivative order is.
Detailed finite element method modeling of evaporating multi-component droplets
Diddens, Christian, E-mail: C.Diddens@tue.nl
2017-07-01
The evaporation of sessile multi-component droplets is modeled with an axisymmetic finite element method. The model comprises the coupled processes of mixture evaporation, multi-component flow with composition-dependent fluid properties and thermal effects. Based on representative examples of water–glycerol and water–ethanol droplets, regular and chaotic examples of solutal Marangoni flows are discussed. Furthermore, the relevance of the substrate thickness for the evaporative cooling of volatile binary mixture droplets is pointed out. It is shown how the evaporation of the more volatile component can drastically decrease the interface temperature, so that ambient vapor of the less volatile component condenses on the droplet. Finally, results of this model are compared with corresponding results of a lubrication theory model, showing that the application of lubrication theory can cause considerable errors even for moderate contact angles of 40°. - Graphical abstract:.
INFLUENCE OF SURFACE-ACTIVE ELEMENTS ON FLUID FLOW OF MIG WELDPOOL
J.S.Sun; J.Q.Gao; Y.Fcng; Y.W.Luan
2004-01-01
A mathematical model describing the behavior of metal inert gas(MIG)welding is formulated in the paper.By means of numerical simulation,the influence of surfaceactive elements on fluid flow of MIG weldpool is studied.The calculation results show that by adding surface-active elements,the fluid flow behavior is drastically changed and the flow fluid flows from lower to upper in vertical direction at the rear of weldpool(w＞0).The physical phenomenon is explained from the viewpoint of fluid flow behavior of weldpool that the properties of weld metal is greatly improved and the content of diffused hydrogen is reduced,thus providing a basis for developing new welding materials.
Limiting flows of a viscous fluid with stationary separation zones with Re approaching infinity
Taganov, G. I.
1982-01-01
The limiting flows of a viscous noncondensable fluid, which are approached by flows with stationary separation zones behind planar symmetrical bodies, with an unlimited increase in the Reynolds number are studied. Quantitative results are obtained in the case of a circulation flow inside of a separation zone.
Intra-articular psoas tendon release alters fluid flow during hip arthroscopy.
Hanypsiak, Bryan T; Stoll, Marc A; Gerhardt, Michael B; DeLong, Jeffrey M
2012-01-01
While not proven definitively, the hypothesis that intra-articular psoas tendon release allows fluid to track into the retroperitoneal space has been widely accepted. This study attempts to identify the path through which fluid enters the pelvis and retroperitoneal space. Six hemi-pelvis human cadaveric specimens were utilized for this study. 3 specimens underwent a capsulotomy and psoas tendon release, while 3 had only a capsulotomy. Arthroscopy fluid was combined with Barium and Methylene blue, and fluid was run at 50 mmHg for 2 hours. A gross dissection was performed at the end of the arthroscopy and the path of fluid flow into the pelvis and throughout the thigh was identified. All 6 specimens showed extravasation of fluid into the pelvis at the 5 minute mark. Specimens with a psoas tendon release showed an altered pattern of fluid flow. In all three of these specimens, the psoas muscle belly was bright blue, along with the remaining tendon. Two of the 3 specimens showed tracking of fluid along the vasculature in both directions. The volume of fluid tracking into the pelvis was increased following a psoas release. Arthroscopy fluid rapidly enters the pelvis following the initiation of hip arthroscopy, regardless of the status of the psoas tendon. Release of the psoas tendon allows fluid to diffuse into the psoas muscle and anterior medial thigh, tracking both proximally and distally along the neurovascular structures, and the volume of fluid tracking into the pelvis is increased following a psoas release.
Desosamine in multicomponent reactions
Achatz, Sepp; Dömling, Alexander
2006-01-01
Desosamine occurring ubiquitously in natural products is introduced into isocyanide based multicomponent reaction chemistry. Corresponding products are of potential interest for the design of novel antibiotics. © 2006.
Desosamine in multicomponent reactions
Achatz, Sepp; Dömling, Alexander
2006-01-01
Desosamine occurring ubiquitously in natural products is introduced into isocyanide based multicomponent reaction chemistry. Corresponding products are of potential interest for the design of novel antibiotics. © 2006.
毛在砂; 杨超; Vassilios C. Kelessidis
2012-01-01
Numerical solution of yield viscoplastic fluid flow is hindered by the singularity inherent to the Herschel-Bulkley model. A finite difference method over the boundary-fitted orthogonal coordinate system is util- ized to investigate numerically the fully developed steady flow of non-Newtonian yield viscoplastic fluid through concentric and eccentric annuli. The fluid rheology is described with the Herschel-Bulkley model. The numerical simulation based on a continuous viscoplastic approach to the Herschel-Bulkley model is found in poor accordance with the experimental data on volumetric flow rate of a bentonite suspension. A strict mathematical model for Herschel-Bulkley fluid flow is established and the corresponding numerical procedures are proposed. However, only the case of flow of a Herschel-Bulkley fluid in a concentric annulus is resolved based on the presumed flow stnicture by using the common optimization technique. Possible flow structures in an eccentric afinulus are presumed, and further challenges in numerical simulation of the Herschel-Bulkley fluid flow are suggested.
Stationary and nonstationary fluid flow of a bose-einstein condensate through a penetrable barrier.
Engels, P; Atherton, C
2007-10-19
We experimentally study the fluid flow induced by a broad, penetrable barrier moving through an elongated dilute gaseous Bose-Einstein condensate. The barrier is created by a laser beam swept through the condensate, and the resulting dipole potential can be either attractive or repulsive. We examine both cases and find regimes of stable and unstable fluid flow: At slow speeds of the barrier, the fluid flow is steady due to the superfluidity of the condensate. At intermediate speeds, we observe an unsteady regime in which the condensate gets filled with dark solitons. At faster speeds, soliton formation completely ceases, and a remarkable absence of excitation in the condensate is seen again.
Stagnation point flow of an non-Newtonian visco-elastic fluid
Teipel, I. [Univ. of Hannover, Inst. of Mechanics, Hannover (Germany)
1985-07-01
In this paper the flow near a two-dimensional stagnation point for a particular non-Newtonian fluid has been studied. Non-Newtonian fluids form a wide class of different materials, which will be used very often in chemical industries. From a practical point of view it is of great importance to obtain some results for example concerning the flow rate and the losses in a tube, the drag and the separation point of a boundary layer flow etc. for such fluids. Therefore it is necessary to assume a particular constitutive equation to calculate various aspects. (author)
Hodographic study of non-Newtonian MHD aligned steady plane fluid flows
P. V. Nguyen
1990-01-01
Full Text Available A study is made of non-Newtonian HHD aligned steady plane fluid flows to find exact solutions for various flow configurations. The equations of motion have been transformed to the hodograph plane. A Legendre-transform function is used to recast the equations in the hodograph plane in terms of this transform function. Solutions for various flow configurations are obtained. Applications are investigated for the fluids of finite and infinite electrical conductivity bringing out the similarities and contrasts in the solutions of these types of fluids.
MUKHOPADHYAY Swati; VAJRAVELU Kuppalapalle
2013-01-01
In this paper we investigate the two-dimensional flow of a non-Newtonian fluid over an unsteady stretching permeable surface.The Casson fluid model is used to characterize the non-Newtonian fluid behavior.First-order constructive/destructive chemical reaction is considered.With the help of a shooting method,numerical solutions for a class of nonlinear coupled differential equations subject to appropriate boundary conditions are obtained.For the steady flow,the exact solution is obtained.The flow features and the mass transfer characteristics for different values of the governing parameters are analyzed and discussed in detail.
Extended Lubrication Theory: Estimation of Fluid Flow in Channels with Variable Geometry
Tavakol, Behrouz; Froehlicher, Guillaume; Stone, Howard A
2014-01-01
Lubrication theory is broadly applicable to the flow characterization of thin fluid films and the motion of particles near surfaces. We offer an extension to lubrication theory by considering higher-order terms of the analytical approximation to describe the fluid flow in a channel with features of a modest aspect ratio. We find good agreement between our analytical results and numerical simulations. We show that the extended lubrication theory is a robust tool for an accurate estimate of laminar fluid flow in channels with features on the order of the channel height, accounting for both smooth and sharp changes in geometry.
Deplano, Valérie; Knapp, Yannick; Bailly, Lucie; Bertrand, Eric
2014-04-11
The aim of this work is to develop a unique in vitro set-up in order to analyse the influence of the shear thinning fluid-properties on the flow dynamics within the bulge of an abdominal aortic aneurysm (AAA). From an experimental point of view, the goals are to elaborate an analogue shear thinning fluid mimicking the macroscopic blood behaviour, to characterise its rheology at low shear rates and to propose an experimental device able to manage such an analogue fluid without altering its feature while reproducing physiological flow rate and pressure, through compliant AAA. Once these experimental prerequisites achieved, the results obtained in the present work show that the flow dynamics is highly dependent on the fluid rheology. The main results point out that the propagation of the vortex ring, generated in the AAA bulge, is slower for shear thinning fluids inducing a smaller travelled distance by the vortex ring so that it never impacts the anterior wall in the distal region, in opposition to Newtonian fluids. Moreover, scalar shear rate values are globally lower for shear thinning fluids inducing higher maximum stress values than those for the Newtonian fluids. Consequently, this work highlights that a Newtonian fluid model is finally inadequate to obtain a reliable prediction of the flow dynamics within AAA.
Influence of the enclosed fluid on the flow over a microstructured surface in the Cassie state
Schönecker, Clarissa; Hardt, Steffen
2013-01-01
Analytical expressions for the flow field as well as for the effective slip length of a shear flow over a surface with periodic rectangular grooves are derived. The primary fluid is in the Cassie state with the grooves being filled with a secondary immiscible fluid. The coupling of both fluids is reflected in a locally varying slip distribution along the fluid-fluid interface, which models the effect of the secondary fluid on the outer flow. The obtained closed-form analytical expressions for the flow field and effective slip length of the primary fluid explicitly contain the influence of the viscosities of the two fluids as well as the magnitude of the local slip, which is a function of the surface geometry. They agree well with results from numerical computations of the full geometry. The analytical expressions allow investigating the influence of the viscous stresses inside the secondary fluid for arbitrary geometries of the rectangular grooves. For classic superhydrophobic surfaces, the deviations in the ...
Hydraulic study of drilling fluid flow in circular and annular tubes
Scheid, C.M.; Calcada, L.A.; Braga, E.R.; Paraiso, E.C.H. [Universidade Federal Rural do Rio de Janeiro (PPGEQ/UFRRJ), Seropedica, RJ (Brazil). Programa de Pos-Graduacao em Engenharia Quimica. Dept. de Engenharia Qumica], E-mail: calcada@ufrrj.br; Martins, A. L. [Petroleo Brasileiro S.A. (CENPES/PETROBRAS), Rio de Janeiro, RJ (Brazil). Centro de Pesquisas
2011-10-15
This study investigates the drilling fluid flow behavior of two water-based drilling fluids in circular and annular tubes. The study has four main objectives: 1) to evaluate correlations between the Power Law and the Casson rheological models, 2) to characterize the flow behavior, 3) to evaluate five hydraulic-diameter equations, and 4) to evaluate the correlations of five turbulent flow-friction factors. The experimental fluid flow loop consisted of one positive displacement pump of 25 HP connected to a 500-liter tank agitated by a 3-HP mixer. The fluids passed through six meters long tubes, arranged in three horizontal rows with independent inlets and outlets. The circular tubes had a 1 inch diameter and were configured as two concentric annular tubes. Annular Tube I had an outer diameter of 1 1/4 inch and an inner diameter of 1/2 inch. Annular Tube II had an outer diameter of 2 inches and an inner diameter of 3/4 inch. The results show that, for the fluids in exam, correlations proposed in the literature were inaccurate as far as predicting hydraulic diameter, estimating pressure drop, and defining the flow regime. In general, the performance of those correlations depended on the fluid properties and on the system's geometry. Finally, literature parameters for some of the correlations were estimated for the two drilling fluids studied. These estimations improved the predictive capacity of calculating the friction factor for real drilling fluids applications for both circular and annular tubes. (author)
Unsteady flow of viscoelastic fluid between two cylinders using fractional Maxwell model
Muhammad Jamil; Constantin Fetecau; Corina Fetecau
2012-01-01
The unsteady flow of an incompressible fractional Maxwell fluid between two infinite coaxial cylinders is studied by means of integral transforms.The motion of the fluid is due to the inner cylinder that applies a time dependent torsional shear to the fluid.The exact solutions for velocity and shear stress are presented in series form in terms of some generalized functions.They can easily be particularized to give similar solutions for Maxwell and Newtonian fluids.Finally,the influence of pertinent parameters on the fluid motion,as well as a comparison between models,is highlighted by graphical illustrations.
Modelling of fluid-structure interaction with multiphase viscous flows using an immersed-body method
Yang, P.; Xiang, J.; Fang, F.; Pavlidis, D.; Latham, J.-P.; Pain, C. C.
2016-09-01
An immersed-body method is developed here to model fluid-structure interaction for multiphase viscous flows. It does this by coupling a finite element multiphase fluid model and a combined finite-discrete element solid model. A coupling term containing the fluid stresses is introduced within a thin shell mesh surrounding the solid surface. The thin shell mesh acts as a numerical delta function in order to help apply the solid-fluid boundary conditions. When used with an advanced interface capturing method, the immersed-body method has the capability to solve problems with fluid-solid interfaces in the presence of multiphase fluid-fluid interfaces. Importantly, the solid-fluid coupling terms are treated implicitly to enable larger time steps to be used. This two-way coupling method has been validated by three numerical test cases: a free falling cylinder in a fluid at rest, elastic membrane and a collapsing column of water moving an initially stationary solid square. A fourth simulation example is of a water-air interface with a floating solid square being moved around by complex hydrodynamic flows including wave breaking. The results show that the immersed-body method is an effective approach for two-way solid-fluid coupling in multiphase viscous flows.
Bernini, Diego; Wiedenbeck, Michael; Dolejš, David; Keppler, Hans
2013-01-01
We have performed phase equilibrium experiments in the system forsterite-enstatite-pyrope-H2O with MgCl2 or MgF2 at 1,100 °C and 2.6 GPa to constrain the solubility of halogens in the peridotite mineral assemblage and the fluid-mineral partition coefficients. The chlorine solubility in forsterite, enstatite and in pyrope is very low, 2.1-3.9 and 4.0-11.4 ppm, respectively, and it is independent of the fluid salinity (0.3-30 wt% Cl), suggesting that some intrinsic saturation limit in the crystal is reached already at very low chlorine concentrations. Chlorine is therefore exceedingly incompatible in upper-mantle minerals. The fluorine solubility is 170-336 ppm in enstatite and 510-1,110 ppm in pyrope, again independent of fluid salinity. Forsterite dissolves 1,750-1,900 ppm up to a fluid salinity of 1.6 wt% F. At higher fluorine contents in the system, forsterite is replaced by the minerals of the humite group. The lower solubility of chlorine by three orders of magnitude when compared to fluorine is consistent with increasing lattice strain. Fluid-mineral partition coefficients are 100-102 for fluorine and 103-105 for chlorine. Since the latter values are orders of magnitude higher than those for hydroxyl partitioning, fluid flow from the subducting slab through the mantle wedge will lead to an efficient sequestration of H2O into the nominally anhydrous minerals in the wedge, whereas chlorine becomes enriched in the residual fluid. Simple mass balance calculations reveal that rock-fluid ratios of up to >3,000 are required to produce the elevated Cl/H2O ratios observed in some primitive arc magmas. Accordingly, fluid flow from the subducted slab into the zone of melting in the mantle wedge does not only occur rapidly in narrow channels, but at least in some subduction zones, fluid pervasively infiltrates the mantle peridotite and interacts with a large volume of the mantle wedge. Together with the Cl/H2O ratios of primitive arc magmas, our data therefore constrain
M Soltani
Full Text Available Modeling of interstitial fluid flow involves processes such as fluid diffusion, convective transport in extracellular matrix, and extravasation from blood vessels. To date, majority of microvascular flow modeling has been done at different levels and scales mostly on simple tumor shapes with their capillaries. However, with our proposed numerical model, more complex and realistic tumor shapes and capillary networks can be studied. Both blood flow through a capillary network, which is induced by a solid tumor, and fluid flow in tumor's surrounding tissue are formulated. First, governing equations of angiogenesis are implemented to specify the different domains for the network and interstitium. Then, governing equations for flow modeling are introduced for different domains. The conservation laws for mass and momentum (including continuity equation, Darcy's law for tissue, and simplified Navier-Stokes equation for blood flow through capillaries are used for simulating interstitial and intravascular flows and Starling's law is used for closing this system of equations and coupling the intravascular and extravascular flows. This is the first study of flow modeling in solid tumors to naturalistically couple intravascular and extravascular flow through a network. This network is generated by sprouting angiogenesis and consisting of one parent vessel connected to the network while taking into account the non-continuous behavior of blood, adaptability of capillary diameter to hemodynamics and metabolic stimuli, non-Newtonian blood flow, and phase separation of blood flow in capillary bifurcation. The incorporation of the outlined components beyond the previous models provides a more realistic prediction of interstitial fluid flow pattern in solid tumors and surrounding tissues. Results predict higher interstitial pressure, almost two times, for realistic model compared to the simplified model.
A Theoretical and Experimental Study for a Developing Flow in a Thin Fluid Gap
Wu, Qianhong; Lang, Ji; Jen, Kei-Peng; Nathan, Rungun; Vucbmss Team
2016-11-01
In this paper, we report a novel theoretical and experimental approach to examine a fast developing flow in a thin fluid gap. Although the phenomena are widely observed in industrial applications and biological systems, there is a lack of analytical approach that captures the instantaneous fluid response to a sudden impact. An experimental setup was developed that contains a piston instrumented with a laser displacement sensor and a pressure transducer. A sudden impact was imposed on the piston, creating a fast compaction on the thin fluid gap underneath. The motion of the piston was captured by the laser displacement sensor, and the fluid pressure build-up and relaxation was recorded by the pressure transducer. For this dynamic process, a novel analytical approach was developed. It starts with the inviscid limit when the viscous fluid effect has no time to appear. This short process is followed by a developing flow, in which the inviscid core flow region decreases and the viscous wall region increases until the entire fluid gap is filled with viscous fluid flow. A boundary layer integral method is used during the process. Lastly, the flow is completely viscous dominant featured by a typical squeeze flow in a thin gap. Excellent agreement between the theory and the experiment was achieved. The study presented herein, filling the gap in the literature, will have broad impact in industrial and biomedical applications. This research was supported by the National Science Foundation under Award #1511096.
Beyond Darcy's law: The role of phase topology and ganglion dynamics for two-fluid flow
Armstrong, Ryan T.; McClure, James E.; Berrill, Mark A.; Rücker, Maja; Schlüter, Steffen; Berg, Steffen
2016-10-01
In multiphase flow in porous media the consistent pore to Darcy scale description of two-fluid flow processes has been a long-standing challenge. Immiscible displacement processes occur at the scale of individual pores. However, the larger scale behavior is described by phenomenological relationships such as relative permeability, which typically uses only fluid saturation as a state variable. As a consequence pore scale properties such as contact angle cannot be directly related to Darcy scale flow parameters. Advanced imaging and computational technologies are closing the gap between the pore and Darcy scale, supporting the development of new theory. We utilize fast x-ray microtomography to observe pore-scale two-fluid configurations during immiscible flow and initialize lattice Boltzmann simulations that demonstrate that the mobilization of disconnected nonwetting phase clusters can account for a significant fraction of the total flux. We show that fluid topology can undergo substantial changes during flow at constant saturation, which is one of the underlying causes of hysteretic behavior. Traditional assumptions about fluid configurations are therefore an oversimplification. Our results suggest that the role of fluid connectivity cannot be ignored for multiphase flow. On the Darcy scale, fluid topology and phase connectivity are accounted for by interfacial area and Euler characteristic as parameters that are missing from our current models.
Beyond Darcy's law: The role of phase topology and ganglion dynamics for two-fluid flow.
Armstrong, Ryan T; McClure, James E; Berrill, Mark A; Rücker, Maja; Schlüter, Steffen; Berg, Steffen
2016-10-01
In multiphase flow in porous media the consistent pore to Darcy scale description of two-fluid flow processes has been a long-standing challenge. Immiscible displacement processes occur at the scale of individual pores. However, the larger scale behavior is described by phenomenological relationships such as relative permeability, which typically uses only fluid saturation as a state variable. As a consequence pore scale properties such as contact angle cannot be directly related to Darcy scale flow parameters. Advanced imaging and computational technologies are closing the gap between the pore and Darcy scale, supporting the development of new theory. We utilize fast x-ray microtomography to observe pore-scale two-fluid configurations during immiscible flow and initialize lattice Boltzmann simulations that demonstrate that the mobilization of disconnected nonwetting phase clusters can account for a significant fraction of the total flux. We show that fluid topology can undergo substantial changes during flow at constant saturation, which is one of the underlying causes of hysteretic behavior. Traditional assumptions about fluid configurations are therefore an oversimplification. Our results suggest that the role of fluid connectivity cannot be ignored for multiphase flow. On the Darcy scale, fluid topology and phase connectivity are accounted for by interfacial area and Euler characteristic as parameters that are missing from our current models.
Zhu, Hongjun, E-mail: ticky863@126.com [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu 610500, Sichuan (China); State Key Laboratory of Hydraulics and Mountain River Engineering, Sichuan University, Chengdu 610065, Sichuan (China); Pan, Qian; Zhang, Wenli; Feng, Guang; Li, Xue [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu 610500, Sichuan (China)
2014-07-01
Highlights: • A combined FSI–CFD and DPM computational method is used to investigate flow erosion and deformation of needle valve. • The numerical model is validated with the comparison of measured and predicted erosion rate. • Effects of operation, structure and fluid parameters on flow erosion and flow-induced deformation are discussed. • Particle diameter has the most significant effect on flow erosion. • Inlet rate has the most obvious effect on flow-induced deformation. - Abstract: A three-dimensional fluid–structure interaction (FSI) computational model coupling with a combined continuum and discrete model has been used to predict the flow erosion rate and flow-induced deformation of needle valve. Comparisons with measured data demonstrate good agreement with the predictions of erosion rate. The flow field distribution of gas-particle flow and the erosion rate and deformation of valve core are captured under different operating and structural conditions with different fluid parameters. The effects of inlet velocity, valve opening and inlet valve channel size, particle concentration, particle diameter and particle phase components are discussed in detail. The results indicate that valve tip has the most severe erosion and deformation, and flow field, erosion rate and deformation of valve are all sensitive to inlet condition changes, structural changes and fluid properties changes. The effect of particle diameter on erosion is the most significant, while the influence of inlet rate on deformation is the greatest one.
Numerical Investigation on Fluid Flow in a 90-Degree Curved Pipe with Large Curvature Ratio
Yan Wang
2015-01-01
Full Text Available In order to understand the mechanism of fluid flows in curved pipes, a large number of theoretical and experimental researches have been performed. As a critical parameter of curved pipe, the curvature ratio δ has received much attention, but most of the values of δ are very small (δ<0.1 or relatively small (δ≤0.5. As a preliminary study and simulation this research studied the fluid flow in a 90-degree curved pipe of large curvature ratio. The Detached Eddy Simulation (DES turbulence model was employed to investigate the fluid flows at the Reynolds number range from 5000 to 20000. After validation of the numerical strategy, the pressure and velocity distribution, pressure drop, fluid flow, and secondary flow along the curved pipe were illustrated. The results show that the fluid flow in a curved pipe with large curvature ratio seems to be unlike that in a curved pipe with small curvature ratio. Large curvature ratio makes the internal flow more complicated; thus, the flow patterns, the separation region, and the oscillatory flow are different.
Studies of fluid instabilities in flows of lava and debris
Fink, Jonathan H.
1987-01-01
At least two instabilities have been identified and utilized in lava flow studies: surface folding and gravity instability. Both lead to the development of regularly spaced structures on the surfaces of lava flows. The geometry of surface folds have been used to estimate the rheology of lava flows on other planets. One investigation's analysis assumed that lava flows have a temperature-dependent Newtonian rheology, and that the lava's viscosity decreased exponentially inward from the upper surface. The author reviews studies by other investigators on the analysis of surface folding, the analysis of Taylor instability in lava flows, and the effect of surface folding on debris flows.
On the Study of Viscoelastic Walters' B Fluid in Boundary Layer Flows
Seyed Ali Madani Tonekaboni
2012-01-01
Full Text Available Viscoelastic Walters' B fluid flows for three problems, stagnation-point flow, Blasius flow, and Sakiadis flow, have been investigated. In each problem, Cauchy equations are changed to a nondimensional differential equations using stream functions and with assumption of boundary layer flow. The fourth-order predictor-corrector finite-difference method for solving these nonlinear differential equations has been employed. The results that have been obtained using this method are compared with the results of the last studies, and it is clarified that this method is more accurate. It is also shown that the results of last study about Sakiadis flow of Walter's B fluid are not true. In addition, the effects of order of discretization in the boundaries are investigated. Moreover, it has been discussed about the valid region of Weissenberg numbers for the second-order approximation of viscoelastic fluids in each case of study.
Regional Fluid Flow and Basin Modeling in Northern Alaska
Kelley, Karen D.
2007-01-01
INTRODUCTION The foothills of the Brooks Range contain an enormous accumulation of zinc (Zn) in the form of zinc sulfide and barium (Ba) in the form of barite in Carboniferous shale, chert, and mudstone. Most of the resources and reserves of Zn occur in the Red Dog deposit and others in the Red Dog district; these resources and reserves surpass those of most deposits worldwide in terms of size and grade. In addition to zinc and lead sulfides (which contain silver, Ag) and barite, correlative strata host phosphate deposits. Furthermore, prolific hydrocarbon source rocks of Carboniferous and Triassic to Early Jurassic age generated considerable amounts of petroleum that may have contributed to the world-class petroleum resources of the North Slope. Deposits of Zn-Pb-Ag or barite as large as those in the Brooks Range are very rare on a global basis and, accordingly, multiple coincident favorable factors must be invoked to explain their origins. To improve our understanding of these factors and to contribute to more effective assessments of resources in sedimentary basins of northern Alaska and throughout the world, the Mineral Resources Program and the Energy Resources Program of the U.S. Geological Survey (USGS) initiated a project that was aimed at understanding the petroleum maturation and mineralization history of parts of the Brooks Range that were previously poorly characterized. The project, titled ?Regional Fluid Flow and Basin Modeling in Northern Alaska,? was undertaken in collaboration with industry, academia, and other government agencies. This Circular contains papers that describe the results of the recently completed project. The studies that are highlighted in these papers have led to a better understanding of the following: *The complex sedimentary facies relationships and depositional settings and the geochemistry of the sedimentary rocks that host the deposits (sections 2 and 3). *The factors responsible for formation of the barite and zinc deposits
EFFECT OF NON-SPHERICAL PARTICLES ON THE FLUID TURBULENCE IN A PARTICULATE PIPE FLOW
SUN Lei; LIN Jian-zhong; WU Fa-li; CHEN Yi-min
2004-01-01
In the non-spherical particulate turbulent flows, a set of new fluid fluctuating velocity equations with the non-spherical particle source term were derived, then a new method, which treats the slowly varying functions and rapidly varying functions separately, was proposed to solve the equations, and finally the turbulent intensity and the Reynolds stress of the fluid were obtained by calculating the fluctuating velocity statistically. The equations and method were used to a particulate turbulent pipe flow. The results show that the turbulent intensity and the Reynolds stress are decreased almost inverse proportionally to the fluctuating velocity ratio of particle to fluid. Non-spherical particles have a greater suppressing effect on the turbulence than the spherical particles. The particles with short relaxation time reduce the turbulence intensity of fluid, while the particles with long relaxation time increase the turbulence intensity of fluid. For fixed particle and fluid, the small particles suppress the turbulence and the large particles increase the turbulence.
Stability of fluid flow in a cylindrical annulus
Ludwieg, H.
1984-01-01
Helical flow in an annulus between two coaxial cylinders is investigated with regard to its stability against the formation of helical vortices of the type known as Taylor's annular vortices. Assuming the annulus to be small and the velocities to vary linearly with radius, it is shown that the problem can be reduced to the classical case of flow between two rotating cylinders. An appropriate stability criterion for helical flows is derived from Rayleigh's stability criterion applicable to such flows.
Influence of mechanical rock properties and fracture healing rate on crustal fluid flow dynamics
Sachau, Till; Bons, Paul; Gomez-Rivas, Enrique; Koehn, Daniel; de Riese, Tamara
2016-04-01
Fluid flow in the Earth's crust is very slow over extended periods of time, during which it occurs within the connected pore space of rocks. If the fluid production rate exceeds a certain threshold, matrix permeability alone is insufficient to drain the fluid volume and fluid pressure builds up, thereby reducing the effective stress supported by the rock matrix. Hydraulic fractures form once the effective pressure exceeds the tensile strength of the rock matrix and act subsequently as highly effective fluid conduits. Once local fluid pressure is sufficiently low again, flow ceases and fractures begin to heal. Since fluid flow is controlled by the alternation of fracture permeability and matrix permeability, the flow rate in the system is strongly discontinuous and occurs in intermittent pulses. Resulting hydraulic fracture networks are largely self-organized: opening and subsequent healing of hydraulic fractures depends on the local fluid pressure and on the time-span between fluid pulses. We simulate this process with a computer model and describe the resulting dynamics statistically. Special interest is given to a) the spatially and temporally discontinuous formation and closure of fractures and fracture networks and b) the total flow rate over time. The computer model consists of a crustal-scale dual-porosity setup. Control parameters are the pressure- and time-dependent fracture healing rate, and the strength and the permeability of the intact rock. Statistical analysis involves determination of the multifractal properties and of the power spectral density of the temporal development of the total drainage rate and hydraulic fractures. References Bons, P. D. (2001). The formation of large quartz veins by rapid ascent of fluids in mobile hydrofractures. Tectonophysics, 336, 1-17. Miller, S. a., & Nur, A. (2000). Permeability as a toggle switch in fluid-controlled crustal processes. Earth and Planetary Science Letters, 183(1-2), 133-146. Sachau, T., Bons, P. D
Thermo-fluid dynamics of two-phase flow
Ishii, Mamoru; Ishii, Mamoru; Ishii, M
2006-01-01
Provides a very systematic treatment of two phase flow problems from a theoretical perspectiveProvides an easy to follow treatment of modeling and code devlopemnt of two phase flow related phenomenaCovers new results of two phase flow research such as coverage of fuel cells technology.
Estimation of Dense Image Flow Fields in Fluids
Larsen, Rasmus; Conradsen, Knut; Ersbøll, Bjarne Kjær
1998-01-01
The estimation of flow fields from time sequences of satellite imagery has a number of important applications. For visualisation of cloud or sea ice movements in sequences of crude temporal sampling a satisfactory non-blurred temporal interpolation can be performed only when the flow field...... images. The estimated flow fields are used in a temporal interpolation scheme....
Jamming of particles in a two-dimensional fluid-driven flow
Guariguata, Alfredo; Pascall, Masika A.; Gilmer, Matthew W.; Sum, Amadeu K.; Sloan, E. Dendy; Koh, Carolyn A.; Wu, David T.
2012-12-01
The jamming of particles under flow is of critical importance in a broad range of natural and industrial settings, such as the jamming of ice in rivers, or the plugging of suspended solids in pipeline transport. Relatively few studies have been carried out on jamming of suspended particles under flow, in comparison to the many studies on jamming in gravity-driven flows that have revealed various features of the jamming process. Fluid-driven particle flows differ in several aspects from gravity-driven flows, particularly in being compatible with a range of particle concentrations and velocities. Additionally, there are fluid-particle interactions and hydrodynamic effects. To investigate particle jamming in fluid-driven flows, we have performed both experiments and computer simulations on the flow of circular particles floating over water in an open channel with a restriction. We determined the flow-rate boundary for a dilute-to-dense flow transition, similar to that seen in gravity-driven flows. The maximum particle throughput increased for larger restriction sizes consistent with a Beverloo equation form over the entire range of particle mixtures and restriction sizes. The exponent of ˜3/2 in the Beverloo equation is consistent with approximately constant acceleration of grains due to fluid drag in the immediate region of the opening. We verified that the jamming probability from the dense flow gave a geometric distribution in the number of particles escaping before a jam. The probability of jamming in both experiments and simulations was found to be dependent on the ratio of channel opening to particle size, but only weakly dependent on the fluid flow velocity. Flow entrance effects were measured and observed to affect the jamming probability, and dependence on particle friction coefficient was determined from simulation. A comprehensive model for the jamming probability integrating these observations from the different flow regimes was shown to be in good
One-fluid description of turbulently flowing suspension
L'vov, Victor S.; Pomyalov, Anna
2002-01-01
We suggested a one-fluid model of a turbulent dilute suspension which accounts for the ``two-way'' fluid-particle interactions by $k$-dependent effective density of suspension and additional damping term in the Navier-Stokes equation. We presented analytical description of the particle modification of turbulence including scale invariant suppression of a small $k$ part of turbulent spectrum (independent of the particle response time) and possible enhancemenent of large $k$ region [up to the f...
Scales and effects of fluid flow in the upper crust.
Cathles, L M
1990-04-20
Two of the most important agents of geological change, solar energy and internal heat from the mantle, meet and battle for dominance in propelling aqueous and related fluids in the earth's upper crust. Which prevails and how they interact are subjects of active research. Recent work has demonstrated that both agents can propel fluids over nearly continental-scale distances in a fashion that influences a host of important geological processes and leaves a record in chemical alteration, mineral deposits, and hydrocarbon resources.
Radial flow of slightly compressible fluids: A finite element-finite ...
Journal of the Nigerian Association of Mathematical Physics ... Open Access DOWNLOAD FULL TEXT Subscription or Fee Access. Radial flow of slightly compressible fluids: A finite element-finite differences approach. JA Akpobi, ED Akpobi ...
Existence of solutions of a nonlinear system modelling fluid flow in porous media
dam Besenyei
2006-12-01
Full Text Available We investigate the existence of weak solutions for nonlinear differential equations that describe fluid flow through a porous medium. Existence is proved using the theory of monotone operators, and some examples are given.
Non-newtonian fluid flow through three-dimensional disordered porous media.
Morais, Apiano F; Seybold, Hansjoerg; Herrmann, Hans J; Andrade, José S
2009-11-06
We investigate the flow of various non-newtonian fluids through three-dimensional disordered porous media by direct numerical simulation of momentum transport and continuity equations. Remarkably, our results for power-law (PL) fluids indicate that the flow, when quantified in terms of a properly modified permeability-like index and Reynolds number, can be successfully described by a single (universal) curve over a broad range of Reynolds conditions and power-law exponents. We also study the flow behavior of Bingham fluids described in terms of the Herschel-Bulkley model. In this case, our simulations reveal that the interplay of (i) the disordered geometry of the pore space, (ii) the fluid rheological properties, and (iii) the inertial effects on the flow is responsible for a substantial enhancement of the macroscopic hydraulic conductance of the system at intermediate Reynolds conditions.
Mixed Finite Element Formulation for Magnetic Fluid Oil Flow in Electromagnetic Field
Tan Phey Hoon
2017-01-01
Full Text Available Pressure depletion and high viscosity of crude oil in oil reservoir are the main challenges in oil recovery process. A potential solution is to employ electromagnetic heating coupled with magnetic fluid injection. The present work delivers a fundamental study on the interaction between magnetic fluid flow with electromagnetic field. The two-dimensional, incompressible flow is solved numerically using mixed finite element method. The velocity fields, temperature and pressure are the variables of interest, to be obtained by solving mass, momentum and energy equations coupled with Maxwell’ equations. The fluid stress arises simultaneously with the external magnetic force which mobilises and increases the temperature of the oil flow. Verification is made against available data obtained from different numerical method reported in literature. The results justify feasibility of the mixed finite element formulation as an alternative for the modelling of the magnetic fluid flow.
The impact of fluid flow on force chains in granular media
Mahabadi, Nariman; Jang, Jaewon
2017-01-01
Fluid flow through granular media is an important process found in nature and various engineering applications. The effect of fluid flow on the evolution of force chains in the granular media is explored using the photoelasticity theory. A transparent cell is designed to contain several photoelastic disks of different sizes and to allow fluid flow through the particle packing. Water is injected into the cell while the particle packing is under confining stress. Several images are taken for the conditions of different confining stresses and fluid injection rates. An algorithm of an image processing technique is developed to detect the orientation and magnitude of contact forces. The results show that forces in parallel and transverse to the flow direction increase with increasing water velocity, while parallel force shows a higher increasing rate.
Temperature gradients drive radial fluid flow in Petri dishes and multiwell plates.
Lindsay, Stephen M; Yin, John
2016-06-01
Liquid in a Petri dish spontaneously circulates in a radial pattern, even when the dish is at rest. These fluid flows have been observed and utilized for biological research, but their origins have not been well-studied. Here we used particle-tracking to measure velocities of radial fluid flows, which are shown to be linked to evaporation. Infrared thermal imaging was used to identify thermal gradients at the air-liquid interface and at the bottom of the dish. Two-color ratiometric fluorescence confocal imaging was used to measure thermal gradients in the vertical direction within the fluid. A finite-element model of the fluid, incorporating the measured temperature profiles, shows that buoyancy forces are sufficient to produce flows consistent with the measured particle velocity results. Such flows may arise in other dish or plate formats, and may impact biological research in positive or negative ways.
Star-Shaped Fluid Flow Tool for Use in Making Differential Measurements
England, John Dwight (Inventor); Kelley, Anthony R. (Inventor); Cronise, Raymond J. (Inventor)
2014-01-01
A fluid flow tool's plate-like structure has a ring portion defining a flow hole, a support portion extending radially away from the ring portion and adapted to be coupled to conduit wall, and extensions extending radially away from the ring portion such that a periphery of the plate-like structure is defined by the extensions and trough regions between adjacent extensions. One or more ports formed in the ring portion are in fluid communication with the flow hole. A first manifold in the plate-like structure is in fluid communication with each port communicating with the flow hole. One or more ports are formed in the periphery of the plate-like structure. A second manifold in the plate-like structure is in fluid communication with each port formed in the periphery. The first and second manifolds extend through the plate-like structure to terminate and be accessible at the conduit wall.
Numerical analysis of fluid flow and heat transfer in a helical ...
DR OKE
numerical study to investigate three-dimensional turbulent developing convective ... numerical study on double-pipe helical heat exchanger modeled for laminar fluid flow and ... Boundary layer mesh was generated for both nozzle and helix.
Fluid-particle flow and validation using two-way-coupled mesoscale SPH-DEM
Robinson, Martin; Luding, Stefan; Ramaioli, Marco
2013-01-01
First, a meshless simulation method is presented for multiphase fluid-particle flows with a two-way coupled Smoothed Particle Hydrodynamics (SPH) for the fluid and the Discrete Element Method (DEM) for the solid phase. The unresolved fluid model, based on the locally averaged Navier Stokes equations, is expected to be considerably faster than fully resolved models. Furthermore, in contrast to similar mesh-based Discrete Particle Methods (DPMs), our purely particle-based method enjoys the flex...
Fluid flows through fractured porous media along Beavers-Joseph interfaces
Gruais, Isabelle; Polisevski, Dan
2014-01-01
We study a fluid flow traversing a porous medium and obeying the Darcy's law in the case when this medium is fractured in blocks by an $\\veps$-periodic ($\\veps>0$) distribution of fissures filled with a Stokes fluid. These two flows are coupled by a Beavers-Joseph type interface condition. The existence and uniqueness of this flow in our $\\veps$-periodic structure are proved. As the small period of the distribution shrinks to zero, we study the asymptotic behaviour of the flow when the permea...
Unsteady flow of a thixotropic fluid in a slowly varying pipe
Croudace, Andrew I.; Pritchard, David; Wilson, Stephen K.
2017-08-01
We analyse the unsteady axisymmetric flow of a thixotropic or antithixotropic fluid in a slowly varying cylindrical pipe. We derive general perturbation solutions in regimes of small Deborah numbers, in which thixotropic or antithixotropic effects enter as perturbations to generalised Newtonian flow. We present results for the viscous Moore-Mewis-Wagner model and the viscoplastic Hou\\vska model, and we use these results to elucidate what can be predicted in general about the behaviour of thixotropic and antithixotropic fluids in lubrication flow. The range of behaviour we identify casts doubt on the efficacy of model reduction approaches that postulate a generic cross-pipe flow structure.
A General Approach to Time Periodic Incompressible Viscous Fluid Flow Problems
Geissert, Matthias; Hieber, Matthias; Nguyen, Thieu Huy
2016-06-01
This article develops a general approach to time periodic incompressible fluid flow problems and semilinear evolution equations. It yields, on the one hand, a unified approach to various classical problems in incompressible fluid flow and, on the other hand, gives new results for periodic solutions to the Navier-Stokes-Oseen flow, the Navier-Stokes flow past rotating obstacles, and, in the geophysical setting, for Ornstein-Uhlenbeck and various diffusion equations with rough coefficients. The method is based on a combination of interpolation and topological arguments, as well as on the smoothing properties of the linearized equation.
Longitudinal and transversal flow over a cavity containing a second immiscible fluid
Schönecker, Clarissa
2012-01-01
An analytical solution for the flow field of a shear flow over a rectangular cavity containing a second immiscible fluid is derived. While flow of a single-phase fluid over a cavity is a standard case investigated in fluid dynamics, flow over a cavity which is filled with a second immiscible fluid, has received little attention. The flow filed inside the cavity is considered to define a boundary condition for the outer flow which takes the form of a Navier slip condition with locally varying slip length. The slip-length function is determined from the related problem of lid-driven cavity flow. Based on the Stokes equations and complex analysis it is then possible to derive a closed analytical expression for the flow field over the cavity for both the transversal and the longitudinal case. The result is a comparatively simple function, which displays the dependence of the flow field on the cavity geometry and the medium filling the cavity. The analytically computed flow field agrees well with results obtained ...
Fluid mechanics of dynamic stall. I - Unsteady flow concepts
Ericsson, L. E.; Reding, J. P.
1988-01-01
Advanced military aircraft 'supermaneuverability' requirements entail the sustained operation of airfoils at stalled flow conditions. The present work addresses the effects of separated flow on vehicle dynamics; an analytic method is presented which employs static experimental data to predict the separated flow effect on incompressible unsteady aerodynamics. The key parameters in the analytic relationship between steady and nonsteady aerodynamics are the time-lag before a change of flow conditions can affect the separation-induced aerodynamic loads, the accelerated flow effect, and the moving wall effect.
CFD Study of Fluid Flow in an All-glass Evacuated Tube Solar Water Heater
Ai, Ning; Fan, Jianhua; Li, Yumin
2008-01-01
Abstract: The all-glass evacuated tube solar water heater is one of the most widely used solar thermal technologies. The aim of the paper is to investigate fluid flow in the solar water heater by means of computational fluid dynamics (CFD). The investigation was carried out with a focus...
Stagnation-point flow of the Walters' B' fluid with slip
F. Labropulu
2004-01-01
Full Text Available The steady two-dimensional stagnation point flow of a non-Newtonian Walters' B' fluid with slip is studied. The fluid impinges on the wall either orthogonally or obliquely. A finite difference technique is employed to obtain solutions.
Validation of a new blood-mimicking fluid for use in Doppler flow test objects
Ramnarine, KV; Nassiri, DK; Hoskins, PR; Lubbers, J
1998-01-01
A blood-mimicking fluid (BMF) suitable for use in Doppler flow test objects is described and characterised, The BMF consists of 5 mu m diameter nylon scattering particles suspended in a fluid base of water, glycerol, dextran and surfactant, The acoustical properties of various BMF preparations were
Some new parallel flows due to Lorentz forces in electrically conducting fluids
Pantokratoras, A
2007-01-01
We investigate the fully developed flow between two parallel plates and the film flow over a plate in an electrically conducting fluid under the action of a parallel Lorentz force. Exact analytical solutions are derived for velocity, flow rate and wall shear stress at the plates. The velocity results are presented in figures. All these flows are new and are presented for the first time in the literature.
Simulation of Fluid Flow and Heat Transfer in Porous Medium Using Lattice Boltzmann Method
Wijaya, Imam; Purqon, Acep
2017-07-01
Fluid flow and heat transfer in porous medium are an interesting phenomena to study. One kind example of porous medium is geothermal reservoir. By understanding the fluid flow and heat transfer in porous medium, it help us to understand the phenomena in geothermal reservoir, such as thermal change because of injection process. Thermal change in the reservoir is the most important physical property to known since it has correlation with performance of the reservoir, such as the electrical energy produced by reservoir. In this simulation, we investigate the fluid flow and heat transfer in geothermal reservoir as a simple flow in porous medium canal using Lattice Boltzmann Method. In this simulation, we worked on 2 dimension with nine vectors velocity (D2Q9). To understand the fluid flow and heat transfer in reservoir, we varied the fluid temperature that inject into the reservoir and set the heat source constant at 410°C. The first variation we set the fluid temperature 45°C, second 102.5°C, and the last 307.5°C. Furthermore, we also set the parameter of reservoir such as porosity, density, and injected fluid velocity are constant. Our results show that for the first temperature variation distribution between experiment and simulation is 92.86% match. From second variation shows that there is one pick of thermal distribution and one of turbulence zone, and from the last variation show that there are two pick of thermal distribution and two of turbulence zone.
Experimental study on moving boundaries of fluid flow in porous media
ZHOU HongWei; ZHANG YaHeng; LI AiMin; QIU DaYong
2008-01-01
Researches on the boundary shape of fluid flow in porous media play an important role in engineering practices,such as petroleum exploitation,nuclear waste disposal and groundwater contamination.In this paper,six types of artificial porous samples (emery jade) with different porosities are manufactured.With the background of slow flow in porous media,laboratory experiments are carried out by observing the movement of five types of fluids with different dynamic viscosities in various types of porous media.A digital video recorder is employed to record the complete process of the fluid flow in the porous media.Based on the digital photos of the moving boundaries of fluid flow in porous media,the average displacement and fractal dimension of the moving boundary are estimated for different combinations of porosity and dynamic viscosity.Moreover,the evolution behavior of the average velocity and fractal dimension of the moving boundary with time is known.The statistical relations of the average velocity,the fractal dimension of the moving boundary and the porosity of porous media and the dynamic vis-cosity of fluids are proposed in this paper.It is shown that the front shape of the moving boundary of fluid flow in porous media is an integrated result of the porosity of porous media and the dynamic viscosity of fluids.
Parametric study of fluid flow manipulation with piezoelectric macrofiber composite flaps
Sadeghi, O.; Tarazaga, P.; Stremler, M.; Shahab, S.
2017-04-01
Active Fluid Flow Control (AFFC) has received great research attention due to its significant potential in engineering applications. It is known that drag reduction, turbulence management, flow separation delay and noise suppression through active control can result in significantly increased efficiency of future commercial transport vehicles and gas turbine engines. In microfluidics systems, AFFC has mainly been used to manipulate fluid passing through the microfluidic device. We put forward a conceptual approach for fluid flow manipulation by coupling multiple vibrating structures through flow interactions in an otherwise quiescent fluid. Previous investigations of piezoelectric flaps interacting with a fluid have focused on a single flap. In this work, arrays of closely-spaced, free-standing piezoelectric flaps are attached perpendicular to the bottom surface of a tank. The coupling of vibrating flaps due to their interacting with the surrounding fluid is investigated in air (for calibration) and under water. Actuated flaps are driven with a harmonic input voltage, which results in bending vibration of the flaps that can work with or against the flow-induced bending. The size and spatial distribution of the attached flaps, and the phase and frequency of the input actuation voltage are the key parameters to be investigated in this work. Our analysis will characterize the electrohydroelastic dynamics of active, interacting flaps and the fluid motion induced by the system.
High order methods for incompressible fluid flow: Application to moving boundary problems
Bjoentegaard, Tormod
2008-04-15
Fluid flows with moving boundaries are encountered in a large number of real life situations, with two such types being fluid-structure interaction and free-surface flows. Fluid-structure phenomena are for instance apparent in many hydrodynamic applications; wave effects on offshore structures, sloshing and fluid induced vibrations, and aeroelasticity; flutter and dynamic response. Free-surface flows can be considered as a special case of a fluid-fluid interaction where one of the fluids are practically inviscid, such as air. This type of flows arise in many disciplines such as marine hydrodynamics, chemical engineering, material processing, and geophysics. The driving forces for free-surface flows may be of large scale such as gravity or inertial forces, or forces due to surface tension which operate on a much smaller scale. Free-surface flows with surface tension as a driving mechanism include the flow of bubbles and droplets, and the evolution of capillary waves. In this work we consider incompressible fluid flow, which are governed by the incompressible Navier-Stokes equations. There are several challenges when simulating moving boundary problems numerically, and these include - Spatial discretization - Temporal discretization - Imposition of boundary conditions - Solution strategy for the linear equations. These are some of the issues which will be addressed in this introduction. We will first formulate the problem in the arbitrary Lagrangian-Eulerian framework, and introduce the weak formulation of the problem. Next, we discuss the spatial and temporal discretization before we move to the imposition of surface tension boundary conditions. In the final section we discuss the solution of the resulting linear system of equations. (Author). refs., figs., tabs
Pressure development due to viscous fluid flow through a converging gap
Imhamed, Ahmed
2004-01-01
The behaviour of fluid flow in industrial processes is essential for numerous applications and there have been vast amount of work on the hydrodynamic pressure generated due to the flow of viscous fluid. One major manifestation of hydrodynamic pressure application is the wire coating/drawing process, where the wire is pulled through a unit either conical or cylindrical bore filled with a polymer melt that gives rise to the hydrodynamic pressure inside the unit. The hydrodynamic pressure distr...
The development of an intelligent interface to a computational fluid dynamics flow-solver code
Williams, Anthony D.
1988-01-01
Researchers at NASA Lewis are currently developing an 'intelligent' interface to aid in the development and use of large, computational fluid dynamics flow-solver codes for studying the internal fluid behavior of aerospace propulsion systems. This paper discusses the requirements, design, and implementation of an intelligent interface to Proteus, a general purpose, three-dimensional, Navier-Stokes flow solver. The interface is called PROTAIS to denote its introduction of artificial intelligence (AI) concepts to the Proteus code.
AD JOINT SYMMETRY CONSTRAINTS OF MULTICOMPONENT AKNS EQUATIONS
无
2002-01-01
A soliton hierarchy of multicomponent AKNS equations is generated from an arbitrary order matrix spectral problem,along with its bi-Hamiltonian formulation.Adjoint symmetry constraints are presented to manipulate binary nonlinearization for the associated arbitrary order matrix spectral problem.The resulting spatial and temporal constrained flows are shown to provide integrable decompositions of the multicomponent AKNS equations.
Stachel, T.; Chacko, T.; Luth, R. W.
2017-09-01
Because of the inability of depleted cratonic peridotites to effectively buffer oxygen fugacities when infiltrated by CHO or carbonatitic fluids, it has been proposed recently (Luth and Stachel, 2014) that diamond formation in peridotites typically does not occur by rock-buffered redox reactions as previously thought but by an oxygen-conserving reaction in which minor coexisting CH4 and CO2 components in a water-rich fluid react to form diamond (CO2 + CH4 = 2C + 2H2O). In such fluid-buffered systems, carbon isotope fractionation during diamond precipitation occurs in the presence of two dominant fluid carbon species. Carbon isotope modelling of diamond precipitation from mixed CH4- and CO2-bearing fluids reveals unexpected fundamental differences relative to diamond crystallization from a single carbon fluid species: (1) irrespective of which carbon fluid species (CH4 or CO2) is dominant in the initial fluid, diamond formation is invariably associated with progressive minor (water-rich fluids responsible for diamond formation. Specifically, precipitation of diamonds with δ13C values in the range -4 to -6‰ from mantle-derived fluids with an average δ13C value of -5‰ (derived from evidence not related to diamonds) requires that diamond-forming fluids were relatively reduced and had methane as the dominant carbon species (XCO2 = 0.1-0.5). Application of our model to a recently published set of in-situ carbon isotope analyses for peridotitic diamonds from Marange, Zimbabwe (Smit et al., 2016), which contain CH4 fluid inclusions, allows us to perfectly match the observed co-variations in δ13 C, δ15 N and N content and at the same time explain the previously counter-intuitive observation of progressive 13C enrichment in diamonds that appear to have grown from a fluid with methane as the dominant carbon species. Similarly, the almost complete absence in the published record of progressive 13C depletion trends within diamonds likely reflects ubiquitous
Modeling of movement-induced and flow-induced fluid forces in fast switching valves
Roemer, Daniel Beck; Johansen, Per; Schmidt, Lasse
2015-01-01
Fast switching fluid power valves set strict requirements on performance, size and energy efficiency and simulation models are therefore needed to obtain good designs of such components. The valve moving member is subject to fluid forces depending on the valve flow rate and movement of the valve...... valve design. Simulated results of the total fluid force are presented showing the movement-induced fluid force to be significant for a reference application. The model form established is useful for valve designers during development and for accurate operation simulation....... member itself. These fluid forces may be accurately simulated using Computational Fluid Dynamics (CFD) analysis, but such models suffer from being computationally expensive and is not suited for optimization routines. In this paper, a computationally inexpensive method for modeling the fluid forces...
Krautkramer, C.; Rend, R. R.
2014-12-01
Menstrual flow, which is a result of shedding of uterus endometrium, occurs periodically in sync with a women's hormonal cycle. Management of this flow while allowing women to pursue their normal daily lives is the purpose of many commercial products. Some of these products, e.g. feminine hygiene pads and tampons, utilize porous materials in achieving their goal. In this paper we will demonstrate different phenomena that have been observed in flow of menstrual fluid through these porous materials, share some of the advances made in experimental and analytical study of these phenomena, and also present some of the unsolved challenges and difficulties encountered while studying this kind of flow. Menstrual fluid is generally composed of four main components: blood plasma, blood cells, cervical mucus, and tissue debris. This non-homogeneous, multiphase fluid displays very complex rheological behavior, e. g., yield stress, thixotropy, and visco-elasticity, that varies throughout and between menstrual cycles and among women due to various factors. Flow rates are also highly variable during menstruation and across the population and the rheological properties of the fluid change during the flow into and through the product. In addition to these phenomena, changes to the structure of the porous medium within the product can also be seen due to fouling and/or swelling of the material. This paper will, also, share how the fluid components impact the flow and the consequences for computer simulation, the creation of a simulant fluid and testing methods, and for designing products that best meet consumer needs. We hope to bring to light the challenges of managing this complex flow to meet a basic need of women all over the world. An opportunity exists to apply learnings from research in other disciplines to improve the scientific knowledge related to the flow of this complex fluid through the porous medium that is a sanitary product.
Seismic swarms and fluid flow offshore Central America
Dzierma, Yvonne; Thorwart, Martin; Hensen, Christian; Rabbel, Wolfgang; Wolf, Florian
2010-05-01
Offshore Nicaragua and Northern Costa Rica, the Cocos Plate subducts beneath the Caribbean Plate, carrying with it a large amount of fluids and volatiles. While some of these are set free at great depth beneath the volcanic arc, causing the extremely high water content observed in Nicaraguan mafic magmas (Carr et al., 2003; Kutterolf et al., 2007), some early dehydration reactions already release fluids from the subducting plate underneath the continental slope. Unlike in accretionary margins, where these fluids migrate up along the decollement towards the deformation front, fluid release at erosional margins seems to occur through fractures in the overriding plate (Ranero et al., 2008). Fluid seeps in this region have be observed at seafloor mounds, appearing as side-scan sonar backscatter anomalies or revealed by the presence of chemosynthetic communities (Sahling et al., 2008). In the framework of the General Research Area SFB 574 "Volatiles and Fluids in Subduction Zones", a network of 20 ocean-bottom-stations was deployed offshore Sta Elena Peninsula, Northern Costa Rica, from December 2005 to June 2006. Several distinct swarms of small earthquakes were observed at the seismic stations, which occurred clustered over a time period of several days and have very similar seismic waveforms. Since a correlation of fluid-release sites with the occurrence of sporadic seismic swarms would indicate that fluid migration and fracturing is the mechanism responsible for triggering the earthquake swarms, the events are re-analysed by double-difference localisation to enhance the resolution of the earthquake locations. The results are then considered to estimate the migration velocity and direction and compare the localisations with the known mound sites. Carr, M., Feigenson, M. D., Patino, L. C., and Walker, J. A., 2003: Volcanism and geochemistry in Central America: Progress and problems, in Eiler, J. (ed.), Inside the subduction factory, pp. 153-179, American Geophysical
Dynamic fluid connectivity during steady-state multiphase flow in a sandstone
Reynolds, Catriona A.; Menke, Hannah; Andrew, Matthew; Blunt, Martin J.; Krevor, Samuel
2017-08-01
The current conceptual picture of steady-state multiphase Darcy flow in porous media is that the fluid phases organize into separate flow pathways with stable interfaces. Here we demonstrate a previously unobserved type of steady-state flow behavior, which we term “dynamic connectivity,” using fast pore-scale X-ray imaging. We image the flow of N2 and brine through a permeable sandstone at subsurface reservoir conditions, and low capillary numbers, and at constant fluid saturation. At any instant, the network of pores filled with the nonwetting phase is not necessarily connected. Flow occurs along pathways that periodically reconnect, like cars controlled by traffic lights. This behavior is consistent with an energy balance, where some of the energy of the injected fluids is sporadically converted to create new interfaces.
Adaptive methods in computational fluid dynamics of chemically reacting flows
Rogg, B.
1991-09-01
Possible approaches to fully implicit adaptive algorithms suitable for the numerical simulation of unsteady two-dimensional reactive flows are examined. Emphasis is placed on self-adaptive gridding procedures applicable to time-dependent two-dimensional reactive flows. Pulsating flame propagation, autoignition in a nonpremixed flow, flame propagation in a strained mixing layer, and hot-spot-like self-ignition are considered as examples.
The fluid mechanics of continuous flow electrophoresis in perspective
Saville, D. A.
1980-01-01
Buoyancy alters the flow in continuous flow electrophoresis chambers through the mechanism of hydrodynamic instability and, when the instability is supressed by careful cooling of the chamber boundaries, by restructuring the axial flow. The expanded roles of buoyancy follow upon adapting the size of the chamber and the electric field so as to fractionate certain sorts of cell populations. Scale-up problems, hydrodynamic stability and the altered flow fields are discussed to show how phenomena overlooked in the design and operations of narrow-gap devices take on an overwhelming importance in wide-gap chambers