Analog integrated circuit for micro-gyro interface realized by multi-chip service in Japan; Multi chip service ni yoru micro gyro interface shuseki kairo no sekkei to shisaku

Energy Technology Data Exchange (ETDEWEB)

Maenaka, K.; Fujita, T.; Okamoto, K.; Maeda, M. [Himeji Institute of Technology, Hyogo (Japan)

1998-10-01

This paper deals with an analog integrated circuit for micro-machined gyroscopes with capacitive output. The Integrated circuit was fabricated as a part of the first project from the `Micromachining Multi-Chip Service Cooperative Re-search Committee` organized by The Institute of Electrical Engineers Japan. This multi-chip service project offers a master slice chip with an equivalent of 9 blocks of operational amplifier circuits. Our integrated circuit includes a modulator, demodulator and synchronous rectifier for detecting small changes in the capacitance of a silicon gyroscope. In the paper, the experimental results of fabricated samples will be described. 13 refs., 15 figs.

A wafer-level multi-chip module process with thick photosensitive benzocyclobutene as the dielectric for microwave application

International Nuclear Information System (INIS)

Tang, Jiajie; Sun, Xiaowei; Luo, Le

2011-01-01

A wafer-level microwave multi-chip module (MMCM) packaging process is presented. Thick photosensitive-benzocyclobutene (photo-BCB) polymer (about 25 µm/layer) is used as the dielectric for its simplified process and the capability of obtaining desirable electrical, chemical and mechanical properties at high frequencies. The MMCM packaging structure contains a monolithic microwave integrated circuit (MMIC) chip embedded in a lossy-silicon wafer, a microwave band-pass filter (BPF) and two layers of BCB/Au interconnection. Key processes of fabrication are described in detail. The non-uniformity of BCB film and the sidewall angle of the via-holes for inter-layer connection are tested. Via-chains prepared by metal/BCB multilayer structures are tested through the Kelvin test structure to investigate the resistances of inter-layer connection. The average value is measured to be 73.5 mΩ. The electrical characteristic of this structure is obtained by a microwave transmission performance test from 15 to 30 GHz. The measurement results show good consistency between the bare MMIC die and the packaged die in the test frequency band. The gain of the MMIC chip after packaging is better than 18 dB within the designed operating frequency range (from 23 to 25 GHz). When the packaged MMIC chip is connected to a BPF, the maximum gain is still measured to reach 11.95 dB at 23.8 GHz

A wafer-level 3D packaging structure with Benzocyclobutene as a dielectric for multichip module fabrication

International Nuclear Information System (INIS)

Geng Fei; Ding Xiaoyun; Xu Gaowei; Luo Le

2009-01-01

A new wafer-level 3D packaging structure with Benzocyclobutene (BCB) as interlayer dielectrics (ILDs) for multichip module fabrication is proposed for application in the Ku-band wave. The packaging structure consists of two layers of BCB films and three layers of metallized films, in which the monolithic microwave IC (MMIC), thin film resistors, striplines and microstrip lines are integrated. Wet etched cavities fabricated on the silicon substrate are used for mounting active and passive components. BCB layers cover the components and serve as ILDs for interconnections. Gold bumps are used as electric interconnections between different layers, which eliminates the need to prepare vias by costly dry etching and deposition processes. In order to get high-quality BCB films for the subsequent chemical mechanical planarization (CMP) and multilayer metallization processes, the BCB curing profile is optimized and the roughness of the BCB film after the CMP process is kept lower than 10 nm. The thermal, mechanical and electrical properties of the packaging structure are investigated. The thermal resistance can be controlled below 2 0 C/W. The average shear strength of the gold bumps on the BCB surface is around 70 N/mm 2 . The performances of MMIC and interconnection structure at high frequencies are optimized and tested. The S-parameters curves of the packaged MMIC shift slightly showing perfect transmission character. The insertion loss change after the packaging process is less than 1 dB range at the operating frequency and the return loss is less than -8 dB from 10 to 15 GHz.

Studies on MCM-D pixel-detector-modules

CERN Document Server

Flick, T; Gerlach, P; Grah, C; Mättig, P; Rohe, T

2003-01-01

In the context of the development of the ATLAS-pixel-detector, a technology for building up the high density interconnects has been studied, the MCM-D (multichip module deposited) technology. Results of building up first assemblies have been reported. MCM-D technology allows to build up assemblies with uniformly segmented sensors. Especially the use of 'equal-sized(-bricked)' sensor geometry has been studied.

Technology transfer of military space microprocessor developments

Science.gov (United States)

Gorden, C.; King, D.; Byington, L.; Lanza, D.

1999-01-01

Over the past 13 years the Air Force Research Laboratory (AFRL) has led the development of microprocessors and computers for USAF space and strategic missile applications. As a result of these Air Force development programs, advanced computer technology is available for use by civil and commercial space customers as well. The Generic VHSIC Spaceborne Computer (GVSC) program began in 1985 at AFRL to fulfill a deficiency in the availability of space-qualified data and control processors. GVSC developed a radiation hardened multi-chip version of the 16-bit, Mil-Std 1750A microprocessor. The follow-on to GVSC, the Advanced Spaceborne Computer Module (ASCM) program, was initiated by AFRL to establish two industrial sources for complete, radiation-hardened 16-bit and 32-bit computers and microelectronic components. Development of the Control Processor Module (CPM), the first of two ASCM contract phases, concluded in 1994 with the availability of two sources for space-qualified, 16-bit Mil-Std-1750A computers, cards, multi-chip modules, and integrated circuits. The second phase of the program, the Advanced Technology Insertion Module (ATIM), was completed in December 1997. ATIM developed two single board computers based on 32-bit reduced instruction set computer (RISC) processors. GVSC, CPM, and ATIM technologies are flying or baselined into the majority of today's DoD, NASA, and commercial satellite systems.

Selective Attention in Multi-Chip Address-Event Systems

Directory of Open Access Journals (Sweden)

Giacomo Indiveri

2009-06-01

Full Text Available Selective attention is the strategy used by biological systems to cope with the inherent limits in their available computational resources, in order to efficiently process sensory information. The same strategy can be used in artificial systems that have to process vast amounts of sensory data with limited resources. In this paper we present a neuromorphic VLSI device, the “Selective Attention Chip” (SAC, which can be used to implement these models in multi-chip address-event systems. We also describe a real-time sensory-motor system, which integrates the SAC with a dynamic vision sensor and a robotic actuator. We present experimental results from each component in the system, and demonstrate how the complete system implements a real-time stimulus-driven selective attention model.

Selective attention in multi-chip address-event systems.

Science.gov (United States)

Bartolozzi, Chiara; Indiveri, Giacomo

2009-01-01

Selective attention is the strategy used by biological systems to cope with the inherent limits in their available computational resources, in order to efficiently process sensory information. The same strategy can be used in artificial systems that have to process vast amounts of sensory data with limited resources. In this paper we present a neuromorphic VLSI device, the "Selective Attention Chip" (SAC), which can be used to implement these models in multi-chip address-event systems. We also describe a real-time sensory-motor system, which integrates the SAC with a dynamic vision sensor and a robotic actuator. We present experimental results from each component in the system, and demonstrate how the complete system implements a real-time stimulus-driven selective attention model.

A multichip aVLSI system emulating orientation selectivity of primary visual cortical cells.

Science.gov (United States)

Shimonomura, Kazuhiro; Yagi, Tetsuya

2005-07-01

In this paper, we designed and fabricated a multichip neuromorphic analog very large scale integrated (aVLSI) system, which emulates the orientation selective response of the simple cell in the primary visual cortex. The system consists of a silicon retina and an orientation chip. An image, which is filtered by a concentric center-surround (CS) antagonistic receptive field of the silicon retina, is transferred to the orientation chip. The image transfer from the silicon retina to the orientation chip is carried out with analog signals. The orientation chip selectively aggregates multiple pixels of the silicon retina, mimicking the feedforward model proposed by Hubel and Wiesel. The chip provides the orientation-selective (OS) outputs which are tuned to 0 degrees, 60 degrees, and 120 degrees. The feed-forward aggregation reduces the fixed pattern noise that is due to the mismatch of the transistors in the orientation chip. The spatial properties of the orientation selective response were examined in terms of the adjustable parameters of the chip, i.e., the number of aggregated pixels and size of the receptive field of the silicon retina. The multichip aVLSI architecture used in the present study can be applied to implement higher order cells such as the complex cell of the primary visual cortex.

Influences of Device and Circuit Mismatches on Paralleling Silicon Carbide MOSFETs

DEFF Research Database (Denmark)

Li, Helong; Munk-Nielsen, Stig; Wang, Xiongfei

2016-01-01

This paper addresses the influences of device and circuit mismatches on paralleling the Silicon Carbide (SiC) MOSFETs. Comprehensive theoretical analysis and experimental validation from paralleled discrete devices to paralleled dies in multichip power modules are first presented. Then, the influ......This paper addresses the influences of device and circuit mismatches on paralleling the Silicon Carbide (SiC) MOSFETs. Comprehensive theoretical analysis and experimental validation from paralleled discrete devices to paralleled dies in multichip power modules are first presented. Then......, the influence of circuit mismatch on paralleling SiC MOSFETs is investigated and experimentally evaluated for the first time. It is found that the mismatch of the switching loop stray inductance can also lead to on-state current unbalance with inductive output current, in addition to the on-state resistance...... of the device. It further reveals that circuit mismatches and a current coupling among the paralleled dies exist in a SiC MOSFET multichip power module, which is critical for the transient current distribution in the power module. Thus, a power module layout with an auxiliary source connection is developed...

Custom chipset and compact module design for a 75–110 GHz laboratory signal source

International Nuclear Information System (INIS)

Morgan, Matthew A; Boyd, Tod A; Castro, Jason J

2016-01-01

We report on the development and characterization of a compact, full-waveguide bandwidth (WR-10) signal source for general-purpose testing of mm-wave components. The monolithic microwave integrated circuit (MMIC) based multichip module is designed for compactness and ease-of-use, especially in size-constrained test sets such as a wafer probe station. It takes as input a cm-wave continuous-wave (CW) reference and provides a factor of three frequency multiplication as well as amplification, output power adjustment, and in situ output power monitoring. It utilizes a number of custom MMIC chips such as a Schottky-diode limiter and a broadband mm-wave detector, both designed explicitly for this module, as well as custom millimeter-wave multipliers and amplifiers reported in previous papers. (paper)

Application of Thermal Network Model to Transient Thermal Analysis of Power Electronic Package Substrate

Directory of Open Access Journals (Sweden)

Masaru Ishizuka

2011-01-01

Full Text Available In recent years, there is a growing demand to have smaller and lighter electronic circuits which have greater complexity, multifunctionality, and reliability. High-density multichip packaging technology has been used in order to meet these requirements. The higher the density scale is, the larger the power dissipation per unit area becomes. Therefore, in the designing process, it has become very important to carry out the thermal analysis. However, the heat transport model in multichip modules is very complex, and its treatment is tedious and time consuming. This paper describes an application of the thermal network method to the transient thermal analysis of multichip modules and proposes a simple model for the thermal analysis of multichip modules as a preliminary thermal design tool. On the basis of the result of transient thermal analysis, the validity of the thermal network method and the simple thermal analysis model is confirmed.

Compact electro-thermal modeling of a SiC MOSFET power module under short-circuit conditions

DEFF Research Database (Denmark)

Ceccarelli, Lorenzo; Reigosa, Paula Diaz; Bahman, Amir Sajjad

2017-01-01

A novel physics-based, electro-thermal model which is capable of estimating accurately the short-circuit behavior and thermal instabilities of silicon carbide MOSFET multi-chip power modules is proposed in this paper. The model has been implemented in PSpice and describes the internal structure.......2 kV breakdown voltage and about 300 A rated current. The short-circuit behavior of the module is investigated experimentally through a non-destructive test setup and the model is validated. The estimation of overcurrent and temperature distribution among the chips can provide useful information...

Packaging Aspects of Photodetector Modules for 100 Gbit/s Ethernet Applications

DEFF Research Database (Denmark)

Jiang, Chenhui; Mekonnen, G.G.; Krozer, Viktor

2008-01-01

Packaging is a major problem at millimetre-wave frequencies approaching 100 GHz. In this paper we present that insertion losses in a multi-chip module (MCM) can be less IL ...-backed coplanar waveguides (CBCPWs) with vias is accurately analyzed using 3D electromagnetic (EM) simulation over a wide frequency range. Patch antenna mode resonances are identified as a major origin of resonances in simulated and measured transmission characteristics of the CBCPW with vias. Based on EM...

Tunneling Accelerometer Multichip Module

Science.gov (United States)

Boyadzhyan, V. V.; Choma, J., Jr.

1998-01-01

This paper summarizes and reports a radiation hardened Spacecraft Integrated Sensor/Circut Technology that has been delivered for flight applications to be flown on board STRV-2 (Space Technology Research Vehicle-2).

Switching current imbalance mitigation in power modules with parallel connected SiC MOSFETs

DEFF Research Database (Denmark)

Beczkowski, Szymon; Jørgensen, Asger Bjørn; Li, Helong

2017-01-01

Multichip power modules use parallel connected chips to achieve high current rating. Due to a finite flexibility in a DBC layout, some electrical asymmetries will occur in the module. Parallel connected transistors will exhibit uneven static and dynamic current sharing due to these asymmetries....... Especially important are the couplings between gate and power loops of individual transistors. Fast changing source currents cause gate voltage imbalances yielding uneven switching currents. Equalizing gate voltages seen by paralleled transistors, done by adjusting source bond wires, is proposed...... in this paper. Analysis is performed on an industry standard DBC layout using numerically extracted module parasitics. The method of tuning individual source inductances shows clear improvement in dynamic current balancing and prevents excessive current overshoot during transistors turn-on....

Analysis of Design of Mixed-Signal Electronic Packaging

National Research Council Canada - National Science Library

Pileggi, Lawrence

1999-01-01

The objective of this project is to develop innovative algorithms and prototype tools that will help facilitate the design of mixed signal multi-chip modules and packaging in a manner that is similar...

Parallel Connection of Silicon Carbide MOSFETs for Multichip Power Modules

DEFF Research Database (Denmark)

Li, Helong

challenges from the manufacture and application points of view. The less mature manufacture process limits the yield and the single die size of the SiC MOSFETs, which results a smaller current capability of a single SiC MOSFET die. Consequently, in high current application, the paralleled connections of Si...... connections for the paralleled dies are presented and the source of the transient current imbalance is concluded. To mitigate the transient current imbalance in the traditional DBC layout, a novel DBC layout with split output is proposed. First, the working mechanism of the split output topology is studied...... the current sharing performance among the paralleled SiC MOSFET dies in the power module. The proposed DBC layout is not only limited for SiC MOSFETs, but also for Si IGBTs and other voltage controlled devices. of the circuit mismatch on the paralleled connection of SiC MOSFETs. It reveals the circuit...

The Advances, Challenges and Future Possibilities of Millimeter-Wave Chip-to-Chip Interconnections for Multi-Chip Systems

Directory of Open Access Journals (Sweden)

Amlan Ganguly

2018-02-01

Full Text Available With aggressive scaling of device geometries, density of manufacturing faults is expected to increase. Therefore, yield of complex Multi-Processor Systems-on-Chips (MP-SoCs will decrease due to higher probability of manufacturing defects especially, in dies with large area. Therefore, disintegration of large SoCs into smaller chips called chiplets will improve yield and cost of complex platform-based systems. This will also provide functional flexibility, modular scalability as well as the capability to integrate heterogeneous architectures and technologies in a single unit. However, with scaling of the number of chiplets in such a system, the shared resources in the system such as the interconnection fabric and memory modules will become performance bottlenecks. Additionally, the integration of heterogeneous chiplets operating at different frequencies and voltages can be challenging. State-of-the-art inter-chip communication requires power-hungry high-speed I/O circuits and data transfer over long wired traces on substrates. This increases energy consumption and latency while decreasing data bandwidth for chip-to-chip communication. In this paper, we explore the advances and the challenges of interconnecting a multi-chip system with millimeter-wave (mm-wave wireless interconnects from a variety of perspectives spanning multiple aspects of the wireless interconnection design. Our discussion on the recent advances include aspects such as interconnection topology, physical layer, Medium Access Control (MAC and routing protocols. We also present some potential paradigm-shifting applications as well as complementary technologies of wireless inter-chip communications.

FE-I4 pixel chip characterization with USBpix3 test system

Energy Technology Data Exchange (ETDEWEB)

Filimonov, Viacheslav; Gonella, Laura; Hemperek, Tomasz; Huegging, Fabian; Janssen, Jens; Krueger, Hans; Pohl, David-Leon; Wermes, Norbert [University of Bonn, Bonn (Germany)

2015-07-01

The USBpix readout system is a small and light weighting test system for the ATLAS pixel readout chips. It is widely used to operate and characterize FE-I4 pixel modules in lab and test beam environments. For multi-chip modules the resources on the Multi-IO board, that is the central control unit of the readout system, are coming to their limits, which makes the simultaneous readout of more than one chip at a time challenging. Therefore an upgrade of the current USBpix system has been developed. The upgraded system is called USBpix3 - the main focus of the talk. Characterization of single chip FE-I4 modules was performed with USBpix3 prototype (digital, analog, threshold and source scans; tuning). PyBAR (Bonn ATLAS Readout in Python scripting language) was used as readout software. PyBAR consists of FEI4 DAQ and Data Analysis Libraries in Python. The presentation describes the USBpix3 system, results of FE-I4 modules characterization and preparation for the multi-chip module and multi-module readout with USBpix3.

Electroless Ni-B plating on SiO2 with 3-aminopropyl-triethoxysilane as a barrier layer against Cu diffusion for through-Si via interconnections in a 3-dimensional multi-chip package

International Nuclear Information System (INIS)

Ikeda, Akihiro; Sakamoto, Atsushi; Hattori, Reiji; Kuroki, Yukinori

2009-01-01

Electroless Ni-B was plated on SiO 2 as a barrier layer against Cu diffusion for through-Si via (TSV) interconnections in a 3-dimensional multi-chip package. The electroless Ni-B was deposited on the entire area of the SiO 2 side wall of a deep via with vapor phase pre-deposition of 3-aminopropyl-triethoxysilane on the SiO 2 . The carrier lifetimes in the Si substrates plated with Ni-B/Cu did not decrease with an increase in annealing temperature up to 400 deg. C . The absence of degradation of carrier lifetimes indicates that Cu atoms did not diffuse into the Si through the Ni-B. The advantages of electroless Ni-B (good conformal deposition and forming an effective diffusion barrier against Cu) make it useful as a barrier layer for TSV interconnections in a 3-dimensional multi-chip package

PSpice Modeling Platform for SiC Power MOSFET Modules with Extensive Experimental Validation

DEFF Research Database (Denmark)

Ceccarelli, Lorenzo; Iannuzzo, Francesco; Nawaz, Muhammad

2016-01-01

to simulate the performance of high current rating (above 100 A), multi-chip SiC MOSFET modules both for static and switching behavior. Therefore, the simulation results have been validated experimentally in a wide range of operating conditions, including high temperatures, gate resistance and stray elements....... The whole process has been repeated for three different modules with voltage rating of 1.2 kV and 1.7 kV, manufactured by three different companies. Lastly, a parallel connection of two modules of the same type has been performed in order to observe the unbalancing and mismatches experimentally......The aim of this work is to present a PSpice implementation for a well-established and compact physics-based SiC MOSFET model, including a fast, experimental-based parameter extraction procedure in a MATLAB GUI environment. The model, originally meant for single-die devices, has been used...

Neuromorphic VLSI Models of Selective Attention: From Single Chip Vision Sensors to Multi-chip Systems.

Science.gov (United States)

Indiveri, Giacomo

2008-09-03

Biological organisms perform complex selective attention operations continuously and effortlessly. These operations allow them to quickly determine the motor actions to take in response to combinations of external stimuli and internal states, and to pay attention to subsets of sensory inputs suppressing non salient ones. Selective attention strategies are extremely effective in both natural and artificial systems which have to cope with large amounts of input data and have limited computational resources. One of the main computational primitives used to perform these selection operations is the Winner-Take-All (WTA) network. These types of networks are formed by arrays of coupled computational nodes that selectively amplify the strongest input signals, and suppress the weaker ones. Neuromorphic circuits are an optimal medium for constructing WTA networks and for implementing efficient hardware models of selective attention systems. In this paper we present an overview of selective attention systems based on neuromorphic WTA circuits ranging from single-chip vision sensors for selecting and tracking the position of salient features, to multi-chip systems implement saliency-map based models of selective attention.

Neuromorphic VLSI Models of Selective Attention: From Single Chip Vision Sensors to Multi-chip Systems

Directory of Open Access Journals (Sweden)

Giacomo Indiveri

2008-09-01

Full Text Available Biological organisms perform complex selective attention operations continuously and effortlessly. These operations allow them to quickly determine the motor actions to take in response to combinations of external stimuli and internal states, and to pay attention to subsets of sensory inputs suppressing non salient ones. Selective attention strategies are extremely effective in both natural and artificial systems which have to cope with large amounts of input data and have limited computational resources. One of the main computational primitives used to perform these selection operations is the Winner-Take-All (WTA network. These types of networks are formed by arrays of coupled computational nodes that selectively amplify the strongest input signals, and suppress the weaker ones. Neuromorphic circuits are an optimal medium for constructing WTA networks and for implementing efficient hardware models of selective attention systems. In this paper we present an overview of selective attention systems based on neuromorphic WTA circuits ranging from single-chip vision sensors for selecting and tracking the position of salient features, to multi-chip systems implement saliency-map based models of selective attention.

A multi-chip module for physics experiments

CERN Document Server

Benso, A; Giovannetti, S; Mariani, R; Motto, S; Prinetto, P

1999-01-01

MCMs are widely adopted as assembly solutions for multi-die based systems, where area, performance, and costs are critical constraints. This paper describes both the project strategies and production flow that are to be adopted to realize an MCM-D for data acquisition in high-energy physics experiments. The activity starts from the results of RD/16 CERN project, and is part of the LAP Esprit project. The paper details the most critical issues faced in the production phase, and analyzes how they influenced system partitioning and component design. Moreover, it presents the design-for-testability methodologies adopted at both chip and MCM levels to achieve low defect levels and high production yields, minimizing the overhead in terms of system performance and area occupation. This work should demonstrate the feasibility of the MCM technology in such high speed data processing systems, where both size and cost constraints are important. (10 refs).

Materials Research for GHz Multi-Chip Modules

Science.gov (United States)

1993-09-30

Publications: Laursen, K., Hertling, D., Berry, N., Bidstrup, S.A., Kohl, P., and Arroz , A., "Measurement of the Electrical Properties of Hligh Performance...Materials, Fall 1992. Herding, D.R., Laursen, K., Bidstrup, S.A., Kohl, P.A., Arroz , G.S.., "Measurement of the Electrical Properties of High

FFT Based VLSI Digital One Bit Electronic Warfare Receiver

National Research Council Canada - National Science Library

Chien-In, Henry

1998-01-01

... (1 GHz) digital receiver designed for electronic warfare applications. The receiver can process two simultaneous signals and has the potential for fabrication on a single multi-chip module (MCM...

Development of 10kW SOFC module

Energy Technology Data Exchange (ETDEWEB)

Hisatome, N.; Nagata, K. [Mitsubishi Heavy Industries, Ltd., Nagasaki (Japan); Kakigami, S. [Electric Power Development Co., Inc., Tokyo (Japan)] [and others

1996-12-31

Mitsubishi Heavy industries, Ltd. (MHI) has been developing tubular type Solid Oxide Fuel Cells (SOFC) since 1984. A 1 kW module of SOFC has been continuously operated for 3,000 hours with 2 scheduled thermal cycles at Electric Power Development Co., Inc. (EPDC) Wakamatsu Power Station in 1993. We have obtained of 34% (HHV as H{sub 2}) module efficiency and deterioration rate of 2% Per 1,000 hours in this field test. As for next step, we have developed 10 kW module in 1995. The 10 kW module has been operated for 5,000 hours continuously. This module does not need heating support to maintain the operation temperature, and the module efficiency was 34% (HHV as H{sub 2}). On the other hand, we have started developing the technology of pressurized SOFC. In 1996, pressurized MW module has been tested at MHI Nagasaki Shipyard & Machinery, Works. We are now planning the development of pressurized 10 kW module.

Module Integrated GaN Power Stage for High Switching Frequency Operation

DEFF Research Database (Denmark)

Nour, Yasser; Knott, Arnold

2017-01-01

is integrated on a high glass transition temperature 0.4 mmthick FR4 substrate configured as a 70 pin ball grid arraypackage. The power stage is tested up to switching frequency of12 MHz. The power stage achieved 88.5 % peak efficiency whenconfigured as a soft switching buck converter operating at 7MHz......An increased attention has been detected todevelop smaller and lighter high voltage power converters in therange of 50 V to 400 V domains. The applications for theseconverters are mainly focused for Power over Ethernet (PoE),LED lighting and ac adapters. Design for high power density isone...... of the targets for next generation power converters. Thispaper presents an 80 V input capable multi-chip moduleintegration of enhancement mode gallium nitride (GaN) fieldeffect transistors (FETs) based power stage. The module design ispresented and validated through experimental results. The powerstage...

Photovoltaic module energy rating methodology development

Energy Technology Data Exchange (ETDEWEB)

Kroposki, B.; Myers, D.; Emery, K.; Mrig, L. [National Renewable Energy Lab., Golden, CO (United States); Whitaker, C.; Newmiller, J. [Endecon Engineering, San Ramon, CA (United States)

1996-05-01

A consensus-based methodology to calculate the energy output of a PV module will be described in this paper. The methodology develops a simple measure of PV module performance that provides for a realistic estimate of how a module will perform in specific applications. The approach makes use of the weather data profiles that describe conditions throughout the United States and emphasizes performance differences between various module types. An industry-representative Technical Review Committee has been assembled to provide feedback and guidance on the strawman and final approach used in developing the methodology.

NRL 12-Bit, 213 Msps ADC HSAD9 MCM Evaluation Board

National Research Council Canada - National Science Library

Thai, Khanh

1999-01-01

The MCM Evaluation Board is a 6" by 6" test fixture designed for evaluating the HSAD9 MCM, a completely self contained ADC multichip module that digitizes incoming differential analog signals to 12...

Model Development of Degradation of PV Modules Backsheet with Locating Place of Module

Energy Technology Data Exchange (ETDEWEB)

Kempe, Michael D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wang, Yu [Case Western Reserve University; Fairbrother, Andrew [National Institute of Standards and Technology (NIST); Merzlic, Sebastien [Arkema; Julien, Scott [Northeastern University; Fridman, Lucas S. [Case Western Reserve University; Loyer, Camille [Arkema; Lefebvre, Amy L. [Arkema; O' Brien, Gregory [Arkema; Gu, Xiaohong [National Institute of Standards and Technology (NIST); Ji, Liang [Underwriters Laboratories; Boyce, Kenneth P. [Underwriters Laboratories; Wan, Kai-tak [Northeastern University; French, Roger H. [Case Western Reserve University; Bruckman, Laura S. [Case Western Reserve University

2017-08-23

Performance of a photovoltaic (PV) module is related to the micro-environment around the module. The position of photovoltaic modules in an array row have a large effect on the yellowing and gloss of PV module backsheet exposed in Dfa climatic zone (Gaithersburg, MD) with a polyethylene naphthalate (PEN) outer layer. Stress/Response models of yellowing and gloss-losing as function of location parameters of module, including the shed, row, measurement position in a same module and the distance of module location to the row center, are under development. The module installation height had the greatest influence on degradation of PEN PV backsheet in the Dfa climatic zone. The module backsheets at the end of an array have higher degradation rate (edge effect). The edge effect decreases with increasing of module installation heights.

Getting started with OpenCart module development

CERN Document Server

Nepali, Rupak

2013-01-01

Written as a step-by-step guide, Getting Started with OpenCart Module Development will teach you all you need to know about OpenCart, from custom extensions to module development.This book is for developers who want to develop OpenCart extensions and for those who want to learn more about the code workflow of OpenCart. Basic knowledge of OpenCart would be an added advantage.

Differential Amplitude Pulse-Position Modulation for Indoor Wireless Optical Communications

Directory of Open Access Journals (Sweden)

Sethakaset Ubolthip

2005-01-01

Full Text Available We propose a novel differential amplitude pulse-position modulation (DAPPM for indoor optical wireless communications. DAPPM yields advantages over PPM, DPPM, and DH-PIM in terms of bandwidth requirements, capacity, and peak-to-average power ratio (PAPR. The performance of a DAPPM system with an unequalized receiver is examined over nondispersive and dispersive channels. DAPPM can provide better bandwidth and/or power efficiency than PAM, PPM, DPPM, and DH-PIM depending on the number of amplitude levels and the maximum length of a symbol. We also show that, given the same maximum length, DAPPM has better bandwidth efficiency but requires about and more power than PPM and DPPM, respectively, at high bit rates over a dispersive channel. Conversely, DAPPM requires less power than DH-PIM . When the number of bits per symbol is the same, PAM requires more power, and DH-PIM less power, than DAPPM. Finally, it is shown that the performance of DAPPM can be improved with MLSD, chip-rate DFE, and multichip-rate DFE.

Development of an electro-optic super modulator

International Nuclear Information System (INIS)

Cusack, B; Shaddock, D.

2002-01-01

Full text: Optical phase modulators and amplitude modulators are commonplace in modern laser laboratories. In this talk, we present the development of a device that produces both amplitude modulation (AM) and phase modulation (PM), with a selectable phase relation between the two, on a single free-space Gaussian beam. We term this device a 'super modulator. The device is a version of the Mach-Zehnder modulator, where a beam is split, then separately phase modulated and recombined. Previous work has concentrated on one specific operating point, where the relative modulation phases and the interferometer phase are set to generate single sideband modulation, equivalent to an equal amount of AM and PM in quadrature. Here we are interested in the entire parameter space of amplitude modulation strength, phase modulation strength, and the phase relation between the two. The need for such a super modulator has arisen in the context of control systems for gravitational wave detection interferometers. Typical locking systems are based on the Pound-Drever-Hall method of locking which uses phase modulation. In principle, a super modulator could be used in a PDH configuration, when the locking point of the device will be tunable according to the quantity of AM injected (along with the obligatory PM) into the device

FERMI: a digital Front End and Readout MIcrosystem for high resolution calorimetry

International Nuclear Information System (INIS)

Alexanian, H.; Appelquist, G.; Bailly, P.

1995-01-01

We present a digital solution for the front-end electronics of high resolution calorimeters at future colliders. It is based on analogue signal compression, high speed A/D converters, a fully programmable pipeline and a digital signal processing (DSP) chain with local intelligence and system supervision. This digital solution is aimed at providing maximal front-end processing power by performing waveform analysis using DSP methods. For the system integration of the multichannel device a multi-chip, silicon-on-silicon multi-chip module (MCM) has been adopted. This solution allows a high level of integration of complex analogue and digital functions, with excellent flexibility in mixing technologies for the different functional blocks. This type of multichip integration provides a high degree of reliability and programmability at both the function and the system level, with the additional possibility of customising the microsystem to detector-specific requirements. For enhanced reliability in high radiation environments, fault tolerance strategies, i.e. redundancy, reconfigurability, majority voting and coding for error detection and correction, are integrated into the design. ((orig.))

Developing the impact testing module with labVIEW

International Nuclear Information System (INIS)

Choi, Ki Soo; Jeon, Soo Hong; Jeong, Weui Bong

2007-01-01

Fast Fourier Transformation (FFT) is one of the most useful way to analyze response signal for the purpose of grasping the dynamic characteristics of system. Vibration test using impact hammer is typical and simple experimental method widely used for catching hold of dynamic peculiar characters and modal behaviors of system. In this thesis, impact testing module for NI-PXI equipment is developed. The analyzing and visualizing module are developed with labVIEW tool. A user can see quickly and easily modal shape of system after analyzing acquired data. This developed module will be expected to build up more convenient and serviceable measurement system

Multiplicity-Vertex Detector Electronics Development for Heavy-Ion Detectors

Energy Technology Data Exchange (ETDEWEB)

Britton, C.L., Jr.; Bryan, W.L.; Emery, M.S. [and others

1995-12-31

This paper presents the electronics work performed to date for the Multiplicity-Vertex Detector (MVD) for the PHENIX collaboration at RHIC. The detector consists of approximately 34,000 channels of both silicon strips and silicon pads. The per-channel signal processing chain consists of a pre-amplifier gain stage, a current mode summed multiplicity discriminator, a 64 deep analog memory (simultaneous read/write), an analog correlator, and a 10-bit microsecs ADC. The system controller or Heap Manager, supplies all timing control, data buffering, and data formatting for a single 256-channel multi-chip module (MCM). Each chip set is partitioned into 32-channel sets. Prototype performance for the various blocks will be presented as well as the ionizing radiation damage performance of the 1.2 mu nwell CMOS process used for fabrication.

A Corrosion Investigation of Solder Candidates for High-Temperature Applications

DEFF Research Database (Denmark)

Chidambaram, Vivek; Hald, John; Ambat, Rajan

2009-01-01

The step soldering approach is being employed in the Multi-Chip module (MCM) technology. High lead containing alloys is one of the solders currently being used in this approach. Au-Sn and Au-Ge based candidate alloys have been proposed as alternative solders for this application. In this work...

Development of training modules for magnetic particle inspection

Science.gov (United States)

Kosaka, Daigo; Eisenmann, David J.; Enyart, Darrel; Nakagawa, Norio; Lo, Chester; Orman, David

2015-03-01

Magnetic particle inspection (MPI) is a nondestructive evaluation technique used with ferromagnetic materials. Although the application of this method may appear straightforward, MPI combines the complicated nature of electromagnetics, metallurgical material effects, fluid-particle motion dynamics, and physiological human factors into a single inspection. To fully appreciate industry specifications such as ASTM E-1444, users should develop a basic understanding of the many factors that are involved in MPI. We have developed a series of MPI training modules that are aimed at addressing this requirement. The modules not only offer qualitative explanations, but also show quantitative explanations in terms of measurement and numerical simulation data in many instances. There are five modules in all. Module ♯1 shows characteristics of waveforms and magnetizing methods. This allows MPI practitioners to make optimum choice of waveform and magnetizing method. Module ♯2 explains how material properties relate to the magnetic characteristics. Module ♯3 shows the strength of the excitation field or the flux leakage from a crack and how it compares to the detectability of a crack by MPI. Module ♯4 shows how specimen status may influence defect detection. Module ♯5 shows the effects of particle properties on defect detection.

Getting started with Magento module development

CERN Document Server

Ajzele, Branko

2013-01-01

This project-based tutorial gives you a strong foundation and guides you through practical, real-world examples.This book contains valuable insights for both newbies and already established Magento developers. This book is targeted at new and intermediate PHP developers starting afresh with Magento module development.

Pulse modulator developments in support of klystron testing at SLAC

International Nuclear Information System (INIS)

Koontz, R.F.; Cassel, R.; Lamare, J. de; Ficklin, D.; Gold, S.; Harris, K.

1993-01-01

Several families of high power klystrons in S- and X-Band are being developed in the Klystron Laboratory at SLAC. To support these developments, a number of new pulse modulators are being designed from scratch, or upgraded from existing laboratory test modulators. This paper outlines the modulator parameters available in the SLAC Klystron Laboratory, and discuss two new modulators that are under construction

Instructor's Guide for Human Development Student Modules.

Science.gov (United States)

South Carolina State Dept. of Education, Columbia. Office of Vocational Education.

This instructor's guide is designed for use with an accompanying set of 61 student learning modules on human development. Included among the topics covered in the individual modules are the following: consumer and homemaking education (health and nutrition, personal appearance and grooming, puberty, menstruation, the human reproductive system,…

The ALICE Silicon Pixel Detector System (SPD)

CERN Document Server

Kluge, A; Antinori, Federico; Burns, M; Cali, I A; Campbell, M; Caselle, M; Ceresa, S; Dima, R; Elias, D; Fabris, D; Krivda, Marian; Librizzi, F; Manzari, Vito; Morel, M; Moretto, Sandra; Osmic, F; Pappalardo, G S; Pepato, Adriano; Pulvirenti, A; Riedler, P; Riggi, F; Santoro, R; Stefanini, G; Torcato De Matos, C; Turrisi, R; Tydesjo, H; Viesti, G; PH-EP

2007-01-01

The ALICE silicon pixel detector (SPD) comprises the two innermost layers of the ALICE inner tracker system. The SPD includes 120 detector modules (half-staves) each consisting of 10 ALICE pixel chips bump bonded to two silicon sensors and one multi-chip read-out module. Each pixel chip contains 8192 active cells, so that the total number of pixel cells in the SPD is ≈ 107. The on-detector read-out is based on a multi-chip-module containing 4 ASICs and an optical transceiver module. The constraints on material budget and detector module dimensions are very demanding.

Development and deployment of innovative distance education modules

Energy Technology Data Exchange (ETDEWEB)

Hsu, Wen-Hsing [Nuclear Science Centre, Texas A and M University, 1095 Nuclear Science RD, College Station, Texas 77843 (United States); Reece, W. Daniel [Nuclear Engineering Department, Texas A and M University, College Station, Texas 77843 (United States)

2010-07-01

The potential of distance education/learning to deliver knowledge to learners outside the classroom is increasing dramatically as the technologies evolve. Through the past seven years at Texas A and M University Nuclear Science Centre, media-rich distance learning modules of lectures has been developed using the cutting edge technology available. Accordingly, the framework of modularised distance education modules has been established as well. Each module, closed caption enabled, consists of short interactive videos with animations and quizzes embedded. Those individual videos can be regrouped to form a new module depending on the contents of the lecture. The framework of this system was explained and the procedures of creating those modules were detailed. Different deployment methodologies of those modules were also discussed. (authors)

Development and deployment of innovative distance education modules

International Nuclear Information System (INIS)

Hsu, Wen-Hsing; Reece, W. Daniel

2010-01-01

The potential of distance education/learning to deliver knowledge to learners outside the classroom is increasing dramatically as the technologies evolve. Through the past seven years at Texas A and M University Nuclear Science Centre, media-rich distance learning modules of lectures has been developed using the cutting edge technology available. Accordingly, the framework of modularised distance education modules has been established as well. Each module, closed caption enabled, consists of short interactive videos with animations and quizzes embedded. Those individual videos can be regrouped to form a new module depending on the contents of the lecture. The framework of this system was explained and the procedures of creating those modules were detailed. Different deployment methodologies of those modules were also discussed. (authors)

DEVELOPMENT OF VACUUM SUBLIMATION DRYERS USING THERMOELECTRIC MODULES

Directory of Open Access Journals (Sweden)

R. A. Barykin

2014-01-01

Full Text Available Summary. The main directions of use of freeze-dryed products and ingredients are revealed. The analysis of sales markets of freeze-dryed products is provided. It is shown that introduction of innovative production technologies will allow to develop dynamically not only to the large companies, but also small firms that will create prerequisites for growth of the Russian market of freeze-dryed products. Tendencies of development of the freeze-drying equipment are analysed. Relevance of development of energy saving freeze-dryers is proved The integrated approach to creation of competitive domestic technologies and the equipment for sublimation dehydration of thermolabile products consists in use of the effective combined remedies of a power supply, a process intensification, reduction of specific energy consumption and, as a result, decrease in product cost at achievement of high quality indicators. Advantages of thermoelectric modules as alternative direction to existing vapor-compression and absorbing refrigerating appliances are given. Researches of process of freeze-drying dehydration with use of thermoelectric modules are conducted. It is scientifically confirmed, that the thermoelectric module working at Peltier effect, promotes increase in refrigerating capacity due to use of the principle of the thermal pump. Options of use of thermoelectric modules in designs of dryers are offered. Optimum operating modes and number of modules in section are defined. Ways of increase of power efficiency of freeze-dryers with use of thermoelectric modules are specified. The received results will allow to make engineering calculations and design of progressive freeze-drying installations with various ways of a power supply.

The MARX Modulator Development Program for the International Linear Collider

International Nuclear Information System (INIS)

Leyh, G.E.

2006-01-01

The International Linear Collider (ILC) Marx Modulator Development Program at SLAC is working towards developing a full-scale ILC Marx ''Reference Design'' modulator prototype, with the goal of significantly reducing the size and cost of the ILC modulator while improving overall modulator efficiency and availability. The ILC Reference Design prototype will provide a proof-of-concept model to industry in advance of Phase II SBIR funding, and also allow operation of the new 10MW L-Band Klystron prototypes immediately upon their arrival at SLAC

Development of photovoltaic array and module safety requirements

Science.gov (United States)

1982-01-01

Safety requirements for photovoltaic module and panel designs and configurations likely to be used in residential, intermediate, and large-scale applications were identified and developed. The National Electrical Code and Building Codes were reviewed with respect to present provisions which may be considered to affect the design of photovoltaic modules. Limited testing, primarily in the roof fire resistance field was conducted. Additional studies and further investigations led to the development of a proposed standard for safety for flat-plate photovoltaic modules and panels. Additional work covered the initial investigation of conceptual approaches and temporary deployment, for concept verification purposes, of a differential dc ground-fault detection circuit suitable as a part of a photovoltaic array safety system.

Low power signal processing research at Stanford

Science.gov (United States)

Burr, J.; Williamson, P. R.; Peterson, A.

1991-01-01

This paper gives an overview of the research being conducted at Stanford University's Space, Telecommunications, and Radioscience Laboratory in the area of low energy computation. It discusses the work we are doing in large scale digital VLSI neural networks, interleaved processor and pipelined memory architectures, energy estimation and optimization, multichip module packaging, and low voltage digital logic.

Development of Scientific Approach Based on Discovery Learning Module

Science.gov (United States)

Ellizar, E.; Hardeli, H.; Beltris, S.; Suharni, R.

2018-04-01

Scientific Approach is a learning process, designed to make the students actively construct their own knowledge through stages of scientific method. The scientific approach in learning process can be done by using learning modules. One of the learning model is discovery based learning. Discovery learning is a learning model for the valuable things in learning through various activities, such as observation, experience, and reasoning. In fact, the students’ activity to construct their own knowledge were not optimal. It’s because the available learning modules were not in line with the scientific approach. The purpose of this study was to develop a scientific approach discovery based learning module on Acid Based, also on electrolyte and non-electrolyte solution. The developing process of this chemistry modules use the Plomp Model with three main stages. The stages are preliminary research, prototyping stage, and the assessment stage. The subject of this research was the 10th and 11th Grade of Senior High School students (SMAN 2 Padang). Validation were tested by the experts of Chemistry lecturers and teachers. Practicality of these modules had been tested through questionnaire. The effectiveness had been tested through experimental procedure by comparing student achievement between experiment and control groups. Based on the findings, it can be concluded that the developed scientific approach discovery based learning module significantly improve the students’ learning in Acid-based and Electrolyte solution. The result of the data analysis indicated that the chemistry module was valid in content, construct, and presentation. Chemistry module also has a good practicality level and also accordance with the available time. This chemistry module was also effective, because it can help the students to understand the content of the learning material. That’s proved by the result of learning student. Based on the result can conclude that chemistry module based on

Silicon-Carbide (SIC) Multichip Power Modules (MCPMS) For Power Building Block Applications, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This Small Business Innovation Research Phase I project seeks to prove the feasibility of developing high power density modular power electronic building blocks...

Development of PSA module for computerized accident management support (CAMS)

International Nuclear Information System (INIS)

Iguchi, Yukihiro

1996-10-01

CAMS (Computerised Accident Management Support) is a system that will provide assistance in case of the accidents in a nuclear power plant. The PSA module was developed in order to give useful information in this situation applying the PSA method, which is a comprehensive source of safety knowledge. This module contains plant-specific PSA data, comprising event trees, failure probabilities etc. It has several event trees categorised according to the initiating events. Each event tree has an initiating event frequency and branching probabilities. The various support systems for branches are considered and their dependencies are calculated logically. This module can be activated by data from the state identification (SI) module of CAMS. If an initiating event occurs, the event tree is re-calculated and the PSA module shows which systems of the plant should be activated to bring the plant to a safe state. If the plant responds to the event in the normal way, the plant will be shut down and come to a safe state. However, if some functions do not work, the PSA module generates another path and gives information about the critical systems. If the state of the plant is changed, either by the operators or automatically by the control system, the PSA module follows the new path. Because the estimation of the core damage frequency should be very quick in the accident situation, a simplified model of the event tree and fault trees was adopted. It enabled the PSA module to calculates the CDF within 5 seconds on a standard type work station. The development of the module has been successful. However, further development of the functionality of the module is suggested like real connection to a plant and to the strategy generator module of CAMS, applications for operational support, low power operation optimisation, etc. (author)

Developing Project Based Learning E-Module for the Course of Video Editing

Directory of Open Access Journals (Sweden)

Ketut Krisnayuni

2017-04-01

Full Text Available This study examined the development of an electronic module for the course of video editing and analyzed the students’ response of the e-module. A waterfall model was adopted in the development process of the e-module that consisted of five stages namely (1 analysis; (2 design; (3 implementation; (4 evaluation; and (5 maintenance. The subjects of this study were the students of class XI at SMK Negeri 1 Sukasada. Project Based Learning was used as the basis of the e-module development as the most relevant learning model to meet the students’needs and the schools’ situation. The data of the students’ response about the e-module were collected through a questionnaire. The students’ response was very positive indicated by the mean score of 94,37. It was concluded that the developed e-modul was categorized as very good.

The development of form two mathematics i-Think module (Mi-T2)

Science.gov (United States)

Yao, Foo Jing; Abdullah, Mohd Faizal Nizam Lee; Tien, Lee Tien

2017-05-01

This study aims to develop a training module i-THINK Mathematics Form Two (Mi-T2) to increase the higher-order thinking skills of students. The Mi-T2 training module was built based on the Sidek Module Development Model (2001). Constructivist learning theory, cognitive learning theory, i-THINK map and higher order thinking skills were the building blocks of the module development. In this study, researcher determined the validity and reliability of Mi-T2 module. The design being used in this study was descriptive study. To determine the needs of Mi-T2 module, questionnaires and literature review were used to collect data. When the need of the module was determined, the module was built and a pilot study was conducted to test the reliability of the Mi-T2 module. The pilot study was conducted at a secondary school in North Kinta, Perak. A Form Two class was selected to be the sample study through clustered random sampling. The pilot study was conducted for two months and one topic had been studied. The Mi-T2 module was evaluated by five expert panels to determine the content validity of the module. The instruments being used in the study were questionnaires about the necessity of the Mi-T2 module for guidance, questionnaires about the validity of the module and questionnaires concerning the reliability of the module. Statistical analysis was conducted to determine the validity and reliability coefficients of the Mi-T2 module. The content validity of Mi-T2 module was determined by Cohen's Kappa's (1968) agreement coefficient and the reliability of Mi-T2 module was determined by Cronbach Alpha's value scale. The content validity of Mi-T2 module was 0.89 and the Cronbach Alpha's value of Mi-T2 module was 0.911.

Developing workshop module of realistic mathematics education: Follow-up workshop

Science.gov (United States)

Palupi, E. L. W.; Khabibah, S.

2018-01-01

Realistic Mathematics Education (RME) is a learning approach which fits the aim of the curriculum. The success of RME in teaching mathematics concepts, triggering students’ interest in mathematics and teaching high order thinking skills to the students will make teachers start to learn RME. Hence, RME workshop is often offered and done. This study applied development model proposed by Plomp. Based on the study by RME team, there are three kinds of RME workshop: start-up workshop, follow-up workshop, and quality boost. However, there is no standardized or validated module which is used in that workshops. This study aims to develop a module of RME follow-up workshop which is valid and can be used. Plopm’s developmental model includes materials analysis, design, realization, implementation, and evaluation. Based on the validation, the developed module is valid. While field test shows that the module can be used effectively.

Flexible manufacturing for photonics device assembly

International Nuclear Information System (INIS)

Lu, Shin-yee; Young, K.D.

1994-01-01

The assembly of photonics devices such as laser diodes, optical modulators, and optoelectronics (OE) multi-chip modules usually requires the placement of micron-size devices, and sub-micron precision attachment between optical fibers and diodes or waveguide modulators (pigtailing). This is a labor-intensive process. Studies done by the OE industry have shown that 95% of the cost of a pigtailed photonic device is attributed to the current practice of manual alignment and bonding techniques. At Lawrence Livermore National Laboratory, the authors are working to reduce the cost of packaging OE devices, through the use of automation

Design and development of high voltage MARX modulator technology for long pulse application

International Nuclear Information System (INIS)

Acharya, Mahesh; Shrivastava, Purushottam

2013-01-01

High power pulse modulators are used for powering the RF amplifier like klystrons. This paper describes the development of a 10 kV, 10 A, 1 ms Marx modulator for technology demonstration. The modulator is developed using four no. of main modules each of 2.5 kV. To reduce the over sizing factor of capacitors, the allowed drop of main Marx cell is 9%. A droop compensation circuit has been developed to reduce the output pulse voltage droop from 9% to within ±1%. Droop compensation consists of 10 numbers of corrector modules each of 200 V. A microcontroller based trigger circuit was used for simultaneous triggering of main modules and for staggered triggering of corrector modules. A 25 kV, 10 A, 1 ms Marx modulator is being developed. The advantages of this scheme are oil free design, low DC voltage, adjustable pulse width, adjustable rise time/fall time and modular design etc. (author)

Development of a multi-purpose logic module with the FPGA

International Nuclear Information System (INIS)

Nanbu, K.; Ishikawa, T.; Shimizu, H.

2008-01-01

We have developed a multi-purpose logic module (MPLM) with an FPGA. The internal circuit of this module can be modified easily with the FPGA. This kind of module enables trigger pulse processing for nuclear science. As a first step, the MPLM is used as an event tag generator in experiments with the FOREST detector system. (author)

Development of GREET Catalyst Module

Energy Technology Data Exchange (ETDEWEB)

Wang, Zhichao [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Dunn, Jennifer B. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Cronauer, Donald C. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division

2014-09-01

Catalysts are critical inputs for many pathways that convert biomass into biofuels. Energy consumption and greenhouse gas (GHG) emissions during the production of catalysts and chemical inputs influence the life-cycle energy consumption, and GHG emissions of biofuels and need to be considered in biofuel life-cycle analysis (LCA). In this report, we develop energy and material flows for the production of three different catalysts (tar reforming, alcohol synthesis, Zeolite Socony Mobil-5 [ZSM-5]) and two chemicals (olivine, dimethyl ether of polyethylene glycol [DEPG]). These compounds and catalysts are now included in the Greenhouse Gases, Regulated Emissions and Energy Use in Transportation (GREET™) catalyst module. They were selected because they are consumed in existing U.S. Department of Energy (DOE) analyses of biofuel processes. For example, a thermochemical ethanol production pathway (indirect gasification and mixed alcohol synthesis) developed by the National Renewable Energy Laboratory (NREL) uses olivine, DEPG, and tar reforming and alcohol synthesis catalysts (Dutta et al., 2011). ZSM-5 can be used in biofuel production pathways such as catalytic upgrading of sugars into hydrocarbons (Biddy and Jones, 2013). Other uses for these compounds and catalysts are certainly possible. In this report, we document the data sources and methodology we used to develop material and energy flows for the catalysts and compounds in the GREET catalyst module. In Section 2 we focus on compounds used in the model Dutta et al. (2011) developed. In Section 3, we report material and energy flows associated with ZSM-5 production. Finally, in Section 4, we report results.

Development of a Flipped Medical School Dermatology Module.

Science.gov (United States)

Fox, Joshua; Faber, David; Pikarsky, Solomon; Zhang, Chi; Riley, Richard; Mechaber, Alex; O'Connell, Mark; Kirsner, Robert S

2017-05-01

The flipped classroom module incorporates independent study in advance of in-class instructional sessions. It is unproven whether this methodology is effective within a medical school second-year organ system module. We report the development, implementation, and effectiveness of the flipped classroom methodology in a second-year medical student dermatology module at the University of Miami Leonard M. Miller School of Medicine. In a retrospective cohort analysis, we compared attitudinal survey data and mean scores for a 50-item multiple-choice final examination of the second-year medical students who participated in this 1-week flipped course with those of the previous year's traditional, lecture-based course. Each group comprised nearly 200 students. Students' age, sex, Medical College Admission Test scores, and undergraduate grade point averages were comparable between the flipped and traditional classroom students. The flipped module students' mean final examination score of 92.71% ± 5.03% was greater than that of the traditional module students' 90.92% ± 5.51% ( P flipped methodology to attending live lectures or watching previously recorded lectures. The flipped classroom can be an effective instructional methodology for a medical school second-year organ system module.

Development of control system for the electron gun modulator

International Nuclear Information System (INIS)

Hasegawa, T.; Nagasawa, S.; Kobayashi, T.; Hanaki, H.

2004-01-01

We have been developing a compact and inexpensive electron gun modulator for the SPring-8 Linac. The modulator was redesigned and manufactured to achieve good maintainability and high controllability. A control system of the modulator and a high voltage station is composed mainly of PLCs as a controller and touch panels for human interface. This simplified construction will result in enhancement of its reliability. The rich graphical user interface on the touch panels greatly extends the function of the control system. (author)

Development of a Burnup Module DECBURN Based on the Krylov Subspace Method

Energy Technology Data Exchange (ETDEWEB)

Cho, J. Y.; Kim, K. S.; Shim, H. J.; Song, J. S

2008-05-15

This report is to develop a burnup module DECBURN that is essential for the reactor analysis and the assembly homogenization codes to trace the fuel composition change during the core burnup. The developed burnup module solves the burnup equation by the matrix exponential method based on the Krylov Subspace method. The final solution of the matrix exponential is obtained by the matrix scaling and squaring method. To develop DECBURN module, this report includes the followings as: (1) Krylov Subspace Method for Burnup Equation, (2) Manufacturing of the DECBURN module, (3) Library Structure Setup and Library Manufacturing, (4) Examination of the DECBURN module, (5) Implementation to the DeCART code and Verification. DECBURN library includes the decay constants, one-group cross section and the fission yields. Examination of the DECBURN module is performed by manufacturing a driver program, and the results of the DECBURN module is compared with those of the ORIGEN program. Also, the implemented DECBURN module to the DeCART code is applied to the LWR depletion benchmark and a OPR-1000 pin cell problem, and the solutions are compared with the HELIOS code to verify the computational soundness and accuracy. In this process, the criticality calculation method and the predictor-corrector scheme are introduced to the DeCART code for a function of the homogenization code. The examination by a driver program shows that the DECBURN module produces exactly the same solution with the ORIGEN program. DeCART code that equips the DECBURN module produces a compatible solution to the other codes for the LWR depletion benchmark. Also the multiplication factors of the DeCART code for the OPR-1000 pin cell problem agree to the HELIOS code within 100 pcm over the whole burnup steps. The multiplication factors with the criticality calculation are also compatible with the HELIOS code. These results mean that the developed DECBURN module works soundly and produces an accurate solution

Cost effective second generation AC-modules: Development and testing aspects

International Nuclear Information System (INIS)

Islam, Saiful; Woyte, Achim; Belmans, Ronnie; Heskes, Peter; Rooij, P.M.; Hogedoorn, Ron

2006-01-01

In the framework of the European research project PV2GO, a new AC-module inverter was developed, taking into account all relevant aspects from a European market's point of view (standards, market, application, and research and development goals). The project goal was to achieve the overall system costs of 3 Euro per Wp for a modular plug-and-play photovoltaic system. For the photovoltaic-module, a standard 130-Wp Eurosolare module was chosen. The research and development (R and D) goal was to develop an advanced DC-control system consisting of a state-of-the-art programmable digital device and an Application Specific Integrated Circuit (ASIC) for the AC-control of the inverter. According to the topology concept, thermal and magnetic designs were optimized with regard to production technology and packaging for large-scale production. The new AC-modules were tested in a number of field-test sites in various parts of Europe and their reliability was assessed through Highly Accelerated Stress Tests. Efficiency and power quality have been tested in the laboratory. Further in the PV2GO project an optimization study of the manufacturing process of the new generation of AC-modules for high volume output was done. Another task was the pre-certification procedure to assure compliance with the European guidelines and standards

Advancing clinical development pathways for new CFTR modulators in cystic fibrosis.

Science.gov (United States)

Mayer-Hamblett, Nicole; Boyle, Michael; VanDevanter, Donald

2016-05-01

Cystic fibrosis (CF) is a life-shortening genetic disease affecting approximately 70,000 individuals worldwide. Until recently, drug development efforts have emphasised therapies treating downstream signs and symptoms resulting from the underlying CF biological defect: reduced function of the CF transmembrane conductance regulator (CFTR) protein. The current CF drug development landscape has expanded to include therapies that enhance CFTR function by either restoring wild-type CFTR protein expression or increasing (modulating) the function of mutant CFTR proteins in cells. To date, two systemic small-molecule CFTR modulators have been evaluated in pivotal clinical trials in individuals with CF and specific mutant CFTR genotypes that have led to regulatory review and/or approval. Advances in the discovery of CFTR modulators as a promising new class of therapies have been impressive, yet work remains to develop highly effective, disease-modifying modulators for individuals of all CF genotypes. The objectives of this review are to outline the challenges and opportunities in drug development created by systemic genotype-specific CFTR modulators, highlight the advantages of sweat chloride as an established biomarker of CFTR activity to streamline early-phase development and summarise options for later phase clinical trial designs that respond to the adoption of approved genotype-specific modulators into standard of care. An optimal development framework will be needed to move the most promising therapies efficiently through the drug development pipeline and ultimately deliver efficacious and safe therapies to all individuals with CF. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Recommendations for the development of e-modules for the continuing professional development of European dentists.

Science.gov (United States)

Kavadella, A; Kossioni, A E; Tsiklakis, K; Cowpe, J; Bullock, A; Barnes, E; Bailey, S; Thomas, H; Thomas, R; Karaharju-Suvanto, T; Suomalainen, K; Kersten, H; Povel, E; Giles, M; Walmsley, D; Soboleva, U; Liepa, A; Akota, I

2013-05-01

To provide evidence-based and peer-reviewed recommendations for the development of dental continuing professional development (CPD) learning e-modules. The present recommendations are consensus recommendations of the DentCPD project team and were informed by a literature research, consultations from e-learning and IT expert, discussions amongst the participants attending a special interest group during the 2012 ADEE meeting, and feedback from the evaluation procedures of the exemplar e-module (as described in a companion paper within this Supplement). The main focus of these recommendations is on the courses and modules organised and offered by dental schools. E-modules for dental CPD, as well as for other health professionals' continuing education, have been implemented and evaluated for a number of years. Research shows that the development of e-modules is a team process, undertaken by academics, subject experts, pedagogists, IT and web designers, learning technologists and librarians. The e-module must have clear learning objectives (outcomes), addressing the learners' individual needs, and must be visually attractive, relevant, interactive, promoting critical thinking and providing feedback. The text, graphics and animations must support the objectives and enable the learning process by creating an attractive, easy to navigate and interactive electronic environment. Technology is usually a concern for learners and tutors; therefore, it must be kept simple and interoperable within different systems and software. The pedagogical and technological proficiency of educators is of paramount importance, yet remains a challenge in many instances. The development of e-courses and modules for dental CPD is an endeavour undertaken by a group of professionals. It must be underpinned by sound pedagogical and e-learning principles and must incorporate elements for effective visual learning and visual design and a simple, consistent technology. © 2013 John Wiley & Sons A/S.

Design and development of CAMAC test module

International Nuclear Information System (INIS)

Kulkarni, S.G.; Gore, J. A.; Gupta, A.K.; Saxena, A.

2015-01-01

Various Computer automated measurement and control (CAMAC) modules are used in control and monitoring of Pelletron Accelerator. 24 channels CAMAC Input Gate is used for getting the ON/OFF status of various devices in the Pelletron Accelerator. If a channel has 24 V then the status is 'ON' and if the channel receives 0 V then the status is 'OFF'. Hence we can get the status of 24 different channels though one CAMAC Input Gate module. The status is transported to the PC via CAMAC controller. The manual testing of CAMAC Input Gate involves connection of 24 V to each channel and checking the status of each channel with Graphical user interface (GUI) software. This process of checking input gate is automated by developing a CAMAC Test module which is connected to CAMAC Input Gate with a 50 pin ribbon cable. The Test module automatically generates 24 V /0 V on each channel to be tested depending on the software GUI buttons labeled as 'ON'/'OFF' in labview. The status of CAMAC Input Gate is displayed on GUI for all 24 channels. Hence the user can check the working of each channel on GUI written in labview. This automated process of checking the CAMAC Input Gate saves time to debug problems in module and identifying the bad channel which can be subsequently repaired. The CAMAC Test module uses Spartan 2 FPGA which is connected to 24 transistors which in turn operates 24 relays. 24 V supply is connected to the relay secondary contacts which open/close as per the transistor inputs. The 24 V contacts are connected to the module output connector which should be connected to CAMAC Input Gate which is to be tested. (author)

Development of performance analysis support modules in Younggwang NPP unit 3 and 4

International Nuclear Information System (INIS)

Heo, G. Y.; Lee, S. J.; Jang, S. H.; Choi, S. S.; Choi, Q. H.; Gee, M. H.; Heo, I.

2003-01-01

This paper covers the unmeasured parameter estimation module, the performance degradation estimation module, and the performance degradation diagnosis module that are the supporting modules of the thermal performance analysis program of Younggwang nuclear power plant unit 3 and 4, PERUPS (PERformance UPgrade System), which was developed by KHNP, KEPRI, Hoseo university, and ACT. The unmeasured parameter estimation module plays a role in the generation of estimated values for the parameters that are necessary but there are no sensors. The performance degradation estimation module shows the impact for electric gain and loss according to the parameters related to turbine cycle performance. The performance degradation diagnosis module provides the belief according degradation causes considering the measurement uncertainty, analysis uncertainty, and correlation among parameters. Reference data for the development of each module was prepared by a turbine cycle simulation tool, PEPSE. The unmeasured parameter estimation module and the performance degradation estimation module make the estimation correlations by the regression analysis using the reference data. In the performance degradation diagnosis module, Bayesian network is used for the modeling of uncertainty and knowledge-base. The validation of the developed modules was performed by the test data generated by PEPSE, and accomplished by the actual data again

Development of bouncer-type pulse modulator for the ILC

International Nuclear Information System (INIS)

Akemoto, Mitsuo; Honma, Hiroyuki; Nakajima, Hiromitsu; Shidara, Tetsuo; Fukuda, Shigeki

2009-01-01

This paper describes a long-pulse 1.3 GHz klystron modulator that was recently developed for the Superconducting RF Test Facility (STF) at High Energy Accelerator Research Organization (KEK). The modulator has a direct-switched-type design with a 1:15 step-up transformer and a bouncer circuit to compensate the output phase droop within ±0.5%; it can drive a klystron up to 10 MW peak power, 1.5 ms rf pulse width, and 5 pps repetition rate. The main features of this modulator are four 50 kW switching power supplies in parallel to charge storage capacitors to 10 kV, self-healing-type storage capacitors to realize a compact capacitor bank, and a highly reliable IGBT switch which enables elimination of a crowbar circuit. Design considerations and its performance are presented. An IEGT (Injection Enhanced Gate Transistor) switch, composed of six series devices with a rating of 4.5 kV and 2100 A-DC, has been also developed and tested for R and D to realize a compact modulator. (author)

Development of GREET Catalyst Module

Energy Technology Data Exchange (ETDEWEB)

Wang, Zhichao [Argonne National Lab. (ANL), Argonne, IL (United States); Benavides, Pahola T. [Argonne National Lab. (ANL), Argonne, IL (United States); Dunn, Jennifer B. [Argonne National Lab. (ANL), Argonne, IL (United States); Cronauer, Donald C. [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-09-01

In this report, we develop energy and material flows for the production of five different catalysts (tar reforming, alcohol synthesis, Zeolite Socony Mobil-5 [ZSM-5], Mo/Co/ γ-Al₂O3, and Pt/ γ-Al₂O₃) and two chemicals (olivine, dimethyl ether of polyethylene glycol [DEPG]). These compounds and catalysts are now included in the Greenhouse Gases, Regulated Emissions and Energy Use in Transportation (GREET™) catalyst module.

Mechanical Integrity Issues at MCM-Cs for High Reliability Applications

International Nuclear Information System (INIS)

Morgenstern, H.A.; Tarbutton, T.J.; Becka, G.A.; Uribe, F.; Monroe, S.; Burchett, S.

1998-01-01

During the qualification of a new high reliability low-temperature cofired ceramic (LTCC) multichip module (MCM), two issues relating to the electrical and mechanical integrity of the LTCC network were encountered while performing qualification testing. One was electrical opens after aging tests that were caused by cracks in the solder joints. The other was fracturing of the LTCC networks during mechanical testing. Through failure analysis, computer modeling, bend testing, and test samples, changes were identified. Upon implementation of all these changes, the modules passed testing, and the MCM was placed into production

Development of allosteric modulators of GPCRs for treatment of CNS disorders.

Science.gov (United States)

Nickols, Hilary Highfield; Conn, P Jeffrey

2014-01-01

The discovery of allosteric modulators of G protein-coupled receptors (GPCRs) provides a promising new strategy with potential for developing novel treatments for a variety of central nervous system (CNS) disorders. Traditional drug discovery efforts targeting GPCRs have focused on developing ligands for orthosteric sites which bind endogenous ligands. Allosteric modulators target a site separate from the orthosteric site to modulate receptor function. These allosteric agents can either potentiate (positive allosteric modulator, PAM) or inhibit (negative allosteric modulator, NAM) the receptor response and often provide much greater subtype selectivity than orthosteric ligands for the same receptors. Experimental evidence has revealed more nuanced pharmacological modes of action of allosteric modulators, with some PAMs showing allosteric agonism in combination with positive allosteric modulation in response to endogenous ligand (ago-potentiators) as well as "bitopic" ligands that interact with both the allosteric and orthosteric sites. Drugs targeting the allosteric site allow for increased drug selectivity and potentially decreased adverse side effects. Promising evidence has demonstrated potential utility of a number of allosteric modulators of GPCRs in multiple CNS disorders, including neurodegenerative diseases such as Alzheimer's disease, Parkinson's disease, and Huntington's disease, as well as psychiatric or neurobehavioral diseases such as anxiety, schizophrenia, and addiction. © 2013.

Developing disaster management modules: a collaborative approach.

Science.gov (United States)

Douglas, Valerie

Disasters, whether natural or human induced, can strike when least expected. The events of 9/11 in the US, the 7/7 bombings in the UK, and the anthrax incident in the US on 10th October 2001 indicate that there is a need to have a nursing workforce who is able to respond effectively to mass casualty events and incidents involving chemical, biological, radiological and nuclear substances. Multi-agency collaboration is one of the fundamental principles of disaster preparedness and response. It was therefore necessary to take a similar multi-agency collaborative approach to develop modules on the management of mass casualty events and incidents involving hazardous substances. The modules are offered to registered nurses and registered paramedics. They can be taken independently or as part of a BSc in nursing or health pathway, on a part-time basis. Since the commencement of the modules in September 2004, registered paramedics and registered nurses who work in a wide range of specialties have accessed them.

Development of RF non-IQ sampling module for Helium RFQ LLRF system

Energy Technology Data Exchange (ETDEWEB)

Jeong, Hae-Seong; Ahn, Tae-Sung; Kim, Seong-Gu; Kwon, Hyeok-Jung; Kim, Han-Sung; Song, Young-Gi; Seol, Kyung-Tae; Cho, Yong-Sub [KOMAC, Gyeongju (Korea, Republic of)

2015-05-15

KOMAC (Korea Multi-purpose Accelerator Complex) has a plan to develop the helium irradiation system. This system includes the Ion source, LEBT, RFQ, MEBT systems to transport helium particles to the target. Especially, the RFQ (Radio Frequency Quadrupole) system should receive the 200MHz RF within 1% amplitude error stability. For supplying stable 200MHz RF to the RFQ, the low-level radio frequency (LLRF) should be controlled by control system. The helium RFQ LLRF control system adopted non- IQ sampling method to sample the analog input RF. Sampled input data will be calculated to get the I, Q values. These I, Q values will be used to monitor the amplitude and phase of the RF signal. In this paper, non-IQ sampling logic and amplitude and phase calculating logic of the FPGA will be introduced. Using Xilinx ISE design suite which is tool for developing the FPGA logic module, non-IQ sampling module and amplitude and phase computing module developed. In the future, PI gain module and frequency error computing module will be developed.

Development of Smartphone e-Modul by Problem Solving Method for Biot-Savart Theory

Science.gov (United States)

Prastyaningrum, Ihtiari; Handhika, Jeffry

2017-11-01

Biot-Savart law is an equation that describes the magnetic field created by a current-carrying wire and allows you to calculate its strength at various points. Biot-Savart law is too difficult to be understood, especially about the mathematics concept. Based on the situation, developed an interactive media that’s an Electronic Module. This module based on the problem-solving method and can be accessed by smartphone. This research by using a development method, where is, an electronic module is created by Adobe Flash software. By the development of this module is expected that can improve the ability of mathematics concept analytical.

Perancangan SIMRS Terintegrasi Modul Human Resource Development Pada Rumah Sakit Pendidikan

Directory of Open Access Journals (Sweden)

A.A Primaningrat Gita Puspita

2015-11-01

Full Text Available Human resources at the hospital consists of many kind of disciplines and professions that can be divided into Medical and Non-Medical Personnel. Management Information System Human Resource Development Module needed to accelerate and facilitate the processing of employee data and helpful for management decision making. The module also needs to be integrated with the Payroll Module to facilitate the process of Payroll and remuneration in the hospital. Stage of the system design was conducted by TAS (Total Architecture Syntesis, they are the determination of initial scope, determination of needs, determination of business processes, system design, and evaluation. Human Resource Development Module contains the data collection process, transfer, performance assessment, absences, schedulin, hiring, and reporting. Payroll module contains Payroll and remuneration. This work described by Data Flow Diagrams, Database Structure, and User Interface Design. This design can be used as guidelines for programmers in the manufacture of Hospital Information System are integrated.

Development and validation status of the IFMIF High Flux Test Module

International Nuclear Information System (INIS)

Arbeiter, Frederik; Abou-Sena, Ali; Chen Yuming; Dolensky, Bernhard; Heupel, Tobias; Klein, Christine; Scheel, Nicola; Schlindwein, Georg

2011-01-01

The development of the IFMIF (International Fusion Material Irradiation Facility) High Flux Test Module in the EVEDA (Engineering Validation and Engineering Design Activities) phase up to 2013 includes conceptual design, engineering analyses, as well as design and engineering validation by building of prototypes and their testing. The High Flux Test Module is the device to facilitate the irradiation of SSTT samples of RAFM steels at temperatures 250-550 deg. C and up to an accumulated irradiation damage of 150 dpa. The requirements, the current design and the performance of the module are discussed, and the development process is outlined.

Development and validation status of the IFMIF High Flux Test Module

Energy Technology Data Exchange (ETDEWEB)

Arbeiter, Frederik, E-mail: frederik.arbeiter@kit.edu [Karlsruhe Institute of Technology, Institute for Neutron Physics and Reactor Technology (KIT-INR), Karlsruhe (Germany); Abou-Sena, Ali; Chen Yuming; Dolensky, Bernhard; Heupel, Tobias; Klein, Christine; Scheel, Nicola; Schlindwein, Georg [Karlsruhe Institute of Technology, Institute for Neutron Physics and Reactor Technology (KIT-INR), Karlsruhe (Germany)

2011-10-15

The development of the IFMIF (International Fusion Material Irradiation Facility) High Flux Test Module in the EVEDA (Engineering Validation and Engineering Design Activities) phase up to 2013 includes conceptual design, engineering analyses, as well as design and engineering validation by building of prototypes and their testing. The High Flux Test Module is the device to facilitate the irradiation of SSTT samples of RAFM steels at temperatures 250-550 deg. C and up to an accumulated irradiation damage of 150 dpa. The requirements, the current design and the performance of the module are discussed, and the development process is outlined.

Development of the module inspection system for new standardized radiation monitoring modules

International Nuclear Information System (INIS)

Furukawa, Masami; Shimizu, Kazuaki; Hiruta, Toshihito; Mizugaki, Toshio; Ohi, Yoshihiro; Chida, Tooru.

1994-10-01

This report mentions about the module inspection system which does the maintenance check of the monitoring modules adapted the new monitoring standard, as well as the result of the verification of the modules. The module inspection system is the automatic measurement system with the computer. The system can perform the functional and the characteristic examination of the monitoring modules, the calibration with radiation source and inspection report. In the verification of the monitoring module, three major items were tested, the adaptability for the new monitoring standard, the module functions and each characteristics. All items met the new monitoring standard. (author)

Multichannel CdZnTe Gamma Ray Spectrometer

International Nuclear Information System (INIS)

Doty, F.P.; Lingren, C. L.; Apotovsky, B. A.; Brunsch, J.; Butler, J. F.; Collins, T.; Conwell, R.L.; Friesenhahn, S.; Gormley, J.; Pi, B.; Zhao, S.; Augustine, F.L.; Bennet, B. A.; Cross, E.; James, R. B.

1998-01-01

A 3 cm 3 multichannel gamma spectrometer for DOE applications is under development by Digirad Corporation. The device is based on a position sensitive detector packaged in a compact multi-chip module (MCM) with integrated readout circuitry. The modular, multichannel design will enable identification and quantitative analysis of radionuclides in extended sources, or sources containing low levels of activity. The MCM approach has the advantages that the modules are designed for imaging applications, and the sensitivity can be arbitrarily increased by increasing the number of pixels, i.e. adding modules to the instrument. For a high sensitivity probe, the outputs for each pixel can be corrected for gain and offset variations, and summed digitally. Single pixel results obtained with discrete low noise readout indicate energy resolution of 3 keV can be approached with currently available CdZnTe. The energy resolution demonstrated to date with MCMs for 511 keV gamma rays is 10 keV

Status of development of the HTR module

International Nuclear Information System (INIS)

Weisbrodt, I.A.

1989-01-01

Growing concern about the rising global temperature of the earth due to the ''Greenhouse Effect'' is increasingly focussing worldwide interest on passively safe reactors for heat and power production. In this context the development status of the HTR-Module designed by the Siemens-Group merits strong interest. The HTR-Module has a high degree of passive safety features. Even in case of hypothetical accidents the decay heat is dissipated from the primary system to the environment by passive measures alone i.e. by heat conduction, convection and radiation. The detailed engineering for the HTR-Module continues to progress. In addition to the engineering for the layout considerable progress has been made in the detailed engineering for specific components - e.g. pressure vessel, steam generator, hot gas duct, blower etc. - and specific systems - e.g. first core, helium purification system, reactor safety system, reactor control etc. The procedure for the conceptual licence has been continued. A large number of supplementary analyses and reports have been elaborated and submitted for this procedure. Many workshop meetings have been held with the nominated experts. The hypothetical accidents have been analysed and a special report on these accidents has been submitted. The safety analyses report has been revised, taking into account the results and achievements reached during the ongoing licensing procedure. Parallel to these engineering activities outstanding in R and D work for the HTR-Module, e.g. in the field of fuel elements etc. has been continued. The HTR-Module has found worldwide interest. Respective activities are going on in Bangladesh, PR China, USSR, Indonesia etc. Relevant application studies have been carried out and/or initiated. (author). 15 refs, 16 figs

Development of Active External Network Topology Module for Floodlight SDN Controller

Directory of Open Access Journals (Sweden)

A. A. Noskov

2015-01-01

Full Text Available Traditional network architecture is inflexible and complicated. This observation has led to a paradigm shift towards software-defined networking (SDN, where network management level is separated from data forwarding level. This change was made possible by control plane transfer from the switching equipment to software modules that run on a dedicated server, called the controller (or network operating system, or network applications, that work with this controller. Methods of representation, storage and communication interfaces with network topology elements are the most important aspects of network operating systems available to SDN user because performance of some key controller modules is heavily dependent on internal representation of the network topology. Notably, firewall and routing modules are examples of such modules. This article describes the methods used for presentation and storage of network topologies, as well as interface to the corresponding Floodlight modules. An alternative algorithm has been suggested and developed for message exchange conveying network topology alterations between the controller and network applications. Proposed algorithm makes implementation of module alerting based on subscription to the relevant events. API for interaction between controller and network applications has been developed. This algorithm and API formed the base for Topology Tracker module capable to inform network applications about the changes that had occurred in the network topology and also stores compact representation of the network to speed up the interaction process.

Outsourcing R&D Modules of a New Developing Technology

DEFF Research Database (Denmark)

Pedersen, Jørgen Lindgaard; Perunovic, Zoran

2004-01-01

The paper explores some of the dimensions of the R&D processes: modularity, uncertainty and outsourcing. Ways to divide R&D effort into modules and to argue, either in direction of its modularity, or interdependency, are presented. Further on, uncertainties are segmented into the majors and minors......, and reasons to outsource R&D modules, in the light of these uncertainties, have been investigated. The R&D process has been observed from insulin technologies development over time....

Upgrade of the PreProcessor System for the ATLAS Level-1 Calorimeter Trigger

CERN Document Server

Khomich, A

2010-01-01

The ATLAS Level-1 Calorimeter Trigger is a hardware-based pipelined system designed to identify high-pT objects in the ATLAS calorimeters within a fixed latency of 2.5\\,us. It consists of three subsystems: the PreProcessor which conditions and digitizes analogue signals and two digital processors. The majority of the PreProcessor's tasks are performed on a dense Multi-Chip Module(MCM) consisting of FADCs, a time-adjustment and digital processing ASICs, and LVDS serialisers designed and implemented in ten years old technologies. An MCM substitute, based on today's components (dual channel FADCs and FPGA), is being developed to profit from state-of-the-art electronics and to enhance the flexibility of the digital processing. Development and first test results are presented.

Upgrade of the PreProcessor System for the ATLAS LVL1 Calorimeter Trigger

CERN Document Server

Khomich, A; The ATLAS collaboration

2010-01-01

The ATLAS Level-1 Calorimeter Trigger is a hardware-based pipelined system designed to identify high-pT objects in the ATLAS calorimeters within a fixed latency of 2.5us. It consists of three subsystems: the PreProcessor which conditions and digitizes analogue signals and two digital processors. The majority of the PreProcessor's tasks are performed on a dense Multi-Chip Module(MCM) consisting of FADCs, a time-adjustment and digital processing ASICs, and LVDS serializers designed and implemented in ten years old technologies. An MCM substitute, based on today's components (dual channel FADCs and FPGA), is being developed to profit from state-of-the-art electronics and to enhance the flexibility of the digital processing. Development and first test results are presented.

Superconductive crossbar system for communication applications

International Nuclear Information System (INIS)

Murdock, B.; Kwong, Y.K.; Gimlett, J.

1994-01-01

This paper reviews current efforts toward the integration of a high-speed crossbar switch for digital communication applications. This system is an intelligent switching matrix for 128 inputs and 128 outputs, each capable of 2 Gbs (10 9 bits per second). An array of Josephson junction integrated circuits are interconnected with the use of a superconductive multichip module maintained at 4.2 K. This module is connected to room-temperature electronics by means of flexible cables, each containing impedance-matched microstrip transmission lines. Room-temperature interface electronics will permit interconversion between standard level input/output signals and Josephson junction logic levels. (orig.)

Effect of Career Education Module on Career Development of Community College Students

Science.gov (United States)

Talib, Jasmi A.; Salleh, Amla; Amat, Salleh; Ghavifekr, Simin; Ariff, Azlinda M.

2015-01-01

Using a pre-post and control group design, we examined the effect of a career education module on career development among a group of 122 community college students in Malaysia. The effect of gender and the interaction effect of gender and career education module on career development were also investigated. MANOVA analyses showed significant…

A Development of the Calibration Tool Applied on Analog I/O Modules for Safety-related Controller

International Nuclear Information System (INIS)

Kim, Jong-Kyun; Yun, Dong-Hwa; Lee, Myeong-Kyun; Yoo, Kwan-Woo

2016-01-01

The purpose of this paper is to develop the calibration tool for analog input/output(I/O) modules. Those modules are components in POSAFE-Q which is a programmable logic controller(PLC) that has been developed for the evaluation of safety-related. In this paper, performance improvement of analog I/O modules is presented by developing and applying the calibration tool for each channel in analog I/O modules. With this tool, the input signal to an analog input module and the output signal from an analog output module are able to be satisfied with a reference value of sensor type and an accuracy of all modules. With RS-232 communication, the manual calibration tool is developed for analog I/O modules of an existing and up-to-date version in POSAFE-Q PLC. As a result of applying this tool, the converted value is performant for a type of input sensor and an accuracy of analog I/O modules

Handling Uncertainties within R&D Modules of a developing Technology

DEFF Research Database (Denmark)

Pedersen, Jørgen Lindgaard; Perunovic, Zoran

2004-01-01

. Third, the modules that have had always been present in the insulin's R&D, enabled companies to develop mechanism for internal learning and are able to master that part of the process. Finally, in the R&D, outsourcing is related to the whole knowledge acquisition while it seems that minor uncertainties...... and an interview conducted have generated following. First, the further along the process train a module is, it accumulates uncertainties from previous modules. Second, with the growth of complexity, uncertainties grew as well, resulting in the necessity for companies to seek for knowledge on them externally...

Development of modulators against degenerative aging using radiation fusion technology

Energy Technology Data Exchange (ETDEWEB)

Jo, S. K.; Park, H. R.; Jang, B. S.; Roh, C. H.; Eom, H. S.; Choi, N. H.; Seol, M. A.; Kim, S. H.; Choi, H. M.; Park, M. K.; Shin, H. J.; Ryu, D. K.; Oh, W. J.; Kim, S. H; Yee, S. T.

2012-04-15

1. Objectives Establishment of modelling of degenerative aging using radiation technology Development of aging modulators using radiation degenerative aging model 2. Project results Establishment of the modeling of degenerative aging using radiation technology - The systematic study on the comparison of radiation-induced degeneration and natural aging process in animals and cells confirmed the biological similarity between these two degeneration models - The effective biomarkers were selected for the modelling of degenerative aging using radiation (10 biomarkers for immune/hematopoiesis, 1 for oxidative stress, 6 for molecular signaling, 3 for lipid metabolism) - The optimal irradiation condition was established for the modelling of degerative aging (total 5Gy with fractionation by over 10 times, lapse of over 4 months) - The molecular mechanisms of radiation-induced degeneration were studied including chronic inflammation (lung), inflammation-related lipid metabolism disturbance, mitochondria biogenesis and dynamics - The radiation degenerative model was evaluated with previously known natural substances (resveratrol, EGCG, etc) Development of aging modulators using radiation degenerative aging model - After the screening of about 800 natural herb extracts, 5 effective substances were selected for aging modulation. - 3 candidate compositions were selected from 20 compositions made from effective substances by in vitro evaluation (WAH2, WAH6, WAH7) - 1 composition (WAH6) was selected as the best aging modulator by in vivo evaluation in radiation-induced aging models and degenerative disease models. 3. Expected benefits and plan of application The modelling of degenerative aging using radiation can facilitate the aging research by providing the useful cell/animal models for aging research A large economic benefits are expected by the commercialization of developed aging modulators (over 10 billion KW in 2015.

Development of modulators against degenerative aging using radiation fusion technology

International Nuclear Information System (INIS)

Jo, S. K.; Park, H. R.; Jang, B. S.; Roh, C. H.; Eom, H. S.; Choi, N. H.; Seol, M. A.; Kim, S. H.; Choi, H. M.; Park, M. K.; Shin, H. J.; Ryu, D. K.; Oh, W. J.; Kim, S. H; Yee, S. T.

2012-04-01

1. Objectives Establishment of modelling of degenerative aging using radiation technology Development of aging modulators using radiation degenerative aging model 2. Project results Establishment of the modeling of degenerative aging using radiation technology - The systematic study on the comparison of radiation-induced degeneration and natural aging process in animals and cells confirmed the biological similarity between these two degeneration models - The effective biomarkers were selected for the modelling of degenerative aging using radiation (10 biomarkers for immune/hematopoiesis, 1 for oxidative stress, 6 for molecular signaling, 3 for lipid metabolism) - The optimal irradiation condition was established for the modelling of degerative aging (total 5Gy with fractionation by over 10 times, lapse of over 4 months) - The molecular mechanisms of radiation-induced degeneration were studied including chronic inflammation (lung), inflammation-related lipid metabolism disturbance, mitochondria biogenesis and dynamics - The radiation degenerative model was evaluated with previously known natural substances (resveratrol, EGCG, etc) Development of aging modulators using radiation degenerative aging model - After the screening of about 800 natural herb extracts, 5 effective substances were selected for aging modulation. - 3 candidate compositions were selected from 20 compositions made from effective substances by in vitro evaluation (WAH2, WAH6, WAH7) - 1 composition (WAH6) was selected as the best aging modulator by in vivo evaluation in radiation-induced aging models and degenerative disease models. 3. Expected benefits and plan of application The modelling of degenerative aging using radiation can facilitate the aging research by providing the useful cell/animal models for aging research A large economic benefits are expected by the commercialization of developed aging modulators (over 10 billion KW in 2015

Development of coincidence processing module for PEM

International Nuclear Information System (INIS)

Feng Baotong; Shuai Lei; Li Ke

2011-01-01

For the breast cancer diagnosis and therapy, a prototype of positron emission mammography (PEM) was developed in Institute of High Energy Physics, Chinese Academy of Sciences. In this paper, the design of coincidence processing module (CPM) for this PEM was presented. Both the hardware architecture and the software logic were introduced. In this design, the CPM used the Rocket IO fast interface in FPGA and fiber technology to acquire the preprocessed data from the continuous sampling module (CSM) and then selected the valid event with the coincidence timing window method, which was performed in the FPGA on the daughter board. The CPM transmits the processed data to host computer via gigabit Ethernet. The whole system was controlled by CAN bus. The primary tests indicate that the performance of this design is good. (authors)

Development of 24GHz Rectenna for Receiving and Rectifying Modulated Waves

International Nuclear Information System (INIS)

Shinohara, Naoki; Hatano, Ken

2014-01-01

In this paper, we show experimental results of RF-DC conversion with modulated 24GHz waves. We have already developed class-F MMIC rectenna with resonators for higher harmonics at no modulated 24GHz microwave for RF energy transfer. Dimensions of the MMIC rectifying circuit is 1 mm × 3 mm on GaAs. Maximum RF-DC conversion efficiency is measured 47.9% for a 210 mW microwave input of 24 GHz with a 120 Ω load. The class-F rectenna is based on a single shunt full-wave rectifier. For future application of a simultaneous energy and information transfer system or an energy harvesting from broadcasting waves, input microwave will be modulated. In this paper, we show an experimental result of RF-DC conversion of the class-F rectenna with 24GHz waves modulated by 16QAM as 1st modulation and OFDM as 2nd modulation

Development of 24GHz Rectenna for Receiving and Rectifying Modulated Waves

Science.gov (United States)

Shinohara, Naoki; Hatano, Ken

2014-11-01

In this paper, we show experimental results of RF-DC conversion with modulated 24GHz waves. We have already developed class-F MMIC rectenna with resonators for higher harmonics at no modulated 24GHz microwave for RF energy transfer. Dimensions of the MMIC rectifying circuit is 1 mm × 3 mm on GaAs. Maximum RF-DC conversion efficiency is measured 47.9% for a 210 mW microwave input of 24 GHz with a 120 Ω load. The class-F rectenna is based on a single shunt full-wave rectifier. For future application of a simultaneous energy and information transfer system or an energy harvesting from broadcasting waves, input microwave will be modulated. In this paper, we show an experimental result of RF-DC conversion of the class-F rectenna with 24GHz waves modulated by 16QAM as 1st modulation and OFDM as 2nd modulation.

Development of the integrated system reliability analysis code MODULE

International Nuclear Information System (INIS)

Han, S.H.; Yoo, K.J.; Kim, T.W.

1987-01-01

The major components in a system reliability analysis are the determination of cut sets, importance measure, and uncertainty analysis. Various computer codes have been used for these purposes. For example, SETS and FTAP are used to determine cut sets; Importance for importance calculations; and Sample, CONINT, and MOCUP for uncertainty analysis. There have been problems when the codes run each other and the input and output are not linked, which could result in errors when preparing input for each code. The code MODULE was developed to carry out the above calculations simultaneously without linking input and outputs to other codes. MODULE can also prepare input for SETS for the case of a large fault tree that cannot be handled by MODULE. The flow diagram of the MODULE code is shown. To verify the MODULE code, two examples are selected and the results and computation times are compared with those of SETS, FTAP, CONINT, and MOCUP on both Cyber 170-875 and IBM PC/AT. Two examples are fault trees of the auxiliary feedwater system (AFWS) of Korea Nuclear Units (KNU)-1 and -2, which have 54 gates and 115 events, 39 gates and 92 events, respectively. The MODULE code has the advantage that it can calculate the cut sets, importances, and uncertainties in a single run with little increase in computing time over other codes and that it can be used in personal computers

Design of a two-phase loop thermosyphon for telecommunications system(I): experiments and visualization

Energy Technology Data Exchange (ETDEWEB)

Kim, Won Tae [Kongju National Univ., Kongju (Korea, Republic of); Song, Kyu Sub [Electronics and Telecommunications Research Institute, Taejon (Korea, Republic of); Lee, Young [Univ. of Ottawa, Ontario (Canada)

1998-10-01

A two-phase loop thermosyphon system is developed for the B-ISDN telecommunications system and its performance is evaluated both experimentally and by visualization techniques. The design of the thermosyphon system proposed is aimed to cool MultiChip Modules (MCM) upto heat flux of 8 W/cm{sup 2}. The results indicate that in the loop thermosyphon system cooling heat flux is capable of 12 W/cm{sup 2} with two condensers under the forced convection cooling of the condenser section with acetone or FC-87 as the working fluid. The instability of the working fluid flow within the loop is observed using the visualization techniques and temperature fluctuation is stabilized with orifice insertion.

Design of a two-phase loop thermosyphon for telecommunications system(I): experiments and visualization

International Nuclear Information System (INIS)

Kim, Won Tae; Song, Kyu Sub; Lee, Young

1998-01-01

A two-phase loop thermosyphon system is developed for the B-ISDN telecommunications system and its performance is evaluated both experimentally and by visualization techniques. The design of the thermosyphon system proposed is aimed to cool MultiChip Modules (MCM) upto heat flux of 8 W/cm 2 . The results indicate that in the loop thermosyphon system cooling heat flux is capable of 12 W/cm 2 with two condensers under the forced convection cooling of the condenser section with acetone or FC-87 as the working fluid. The instability of the working fluid flow within the loop is observed using the visualization techniques and temperature fluctuation is stabilized with orifice insertion

Developing a servicelearning module for oral health: A needs assessment

Directory of Open Access Journals (Sweden)

R Ebrahim

2017-03-01

Full Text Available Background. Service learning (SL as a pedagogy in higher education must be differentiated from other services with a primarily philanthropic intent. Dental therapy and oral hygiene students at Sefako Makgatho Health Sciences University, School of Oral Health Sciences, Pretoria, South Africa visit community sites during their 2nd year of study. However, the current curricula would need restructuring for alignment with the espoused pedagogy and standards of SL. Such an SL curriculum design would thus allow for the provision of meaningful services to communities as an integral component of these programmes.Objective. To explore (i perceptions of 2nd-year oral health students; and (ii opinions of academics with regard to the need for an SL module.Methods. Purposive sampling was used to conduct two focus group discussions with academics involved in curriculum development (n=11 and students who had previous exposure to communities (n=10. A survey containing open-ended questions was completed by 9 academics, who would implement the proposed SL module. Frequencies were calculated and data from the open questions were analysed for emergent themes.Results. Most academics (89%, n=8 indicated that working effectively with others as members of a team and developing cultural sensitivity were achievable from an SL module. Two themes emerged from the focus groups, i.e. (i enhanced teaching and learning – students could apply theoretical and clinical training in an authentic setting; and (ii standardisation of training – an SL module would ensure consistency when engaging with communities.Conclusion. The needs assessment was valuable to inform the development and implementation of the SL module.

Development of an e-Learning Research Module Using Multimedia Instruction Approach.

Science.gov (United States)

Kowitlawakul, Yanika; Chan, Moon Fai; Tan, Sharon Swee Lin; Soong, Alan Swee Kit; Chan, Sally Wai Chi

2017-03-01

Students nowadays feel more comfortable with new technologies, which increase their motivation and, as a result, improve their academic performance. In the last two decades, the use of information communication technology has been increasing in many disciplines in higher education. Online learning or e-learning has been used and integrated into the curriculum around the world. A team of nursing faculty and educational technology specialists have developed an e-learning research module and integrate it into the nursing curriculum. The aim was to assist master of nursing and postgraduate nursing students in developing their research knowledge before and throughout their enrollment in the research course. This e-learning module includes interactive multimedia such as audiovisual presentation, graphical theme, animation, case-based learning, and pretest and posttest for each topic area. The module focuses on three main topic areas: (1) basic research principles (for review), (2) quantitative method, and (3) qualitative method. The e-learning module is an innovative use of the information and communication technology to enhance student engagement and learning outcomes in a local context. This article discusses the development journey, piloting process, including the variety of evaluation perspectives, and the ways in which the results influenced the e-learning resource before its wider distribution.

A study on development of monitoring and assessment module for sites

International Nuclear Information System (INIS)

Park, Se Moon; Yoon, Bong Yo; Kim, Dae Jung; Park, Joo Wan; Kim, Chang Lak

2006-01-01

As the development of total management systems for sites along with site environmental information is becoming standard, the system known as the Site Information and Total Environmental database management System (SITES) has been developed over the last two years. The first result was a database management system for storing data obtained from facilities, and a site characterization in addition to an environmental assessment of a site. The SITES database is designed to be effective and practical for use with facility management and safety assessment in relation to Geographic Information Systems. SITES is a total management program, which includes its database, its data analysis system required for site characterization, a safety assessment modeling system and an environment monitoring system. I can contribute to the institutional management of the facility and to its safety reassessment. SITES is composed of two main modules: the SITES Database Module (SDM) and the Monitoring and Assessment (M and A) module. The M and A module is subdivided into two sub-modules: the Safety Assessment System (SAS) and the Site Environmental Monitoring System (SEMS). SAS controls the data (input and output) from the SITES DB for the site safety assessment, whereas SEMS controls the data obtained from the records of the measuring sensors and facilities. The on-line site and environmental monitoring data is managed in SEMS. The present paper introduces the procedure and function of the M and A modules

Orion European Service Module (ESM) Development, Integration and Qualification Status

Science.gov (United States)

Berthe, Philippe; Over, Ann P.; Picardo, Michelle; Byers, Anthony W.

2017-01-01

ESA and the European Industry are supplying the European Service Module for Orion. An overview of the system and subsystem configuration of the Orion European Service Module (ESM) as designed and built for the EM-1 mission is provided as well as an outline of its development, assembly, integration and verification process performed by ESA and NASA in coordination with their respective Industrial prime contractors, Airbus Defence and Space and Lockheed Martin.

Development of a Web-Based 3D Module for Enhanced Neuroanatomy Education.

Science.gov (United States)

Allen, Lauren K; Ren, He Zhen; Eagleson, Roy; de Ribaupierre, Sandrine

2016-01-01

Neuroanatomy is a challenging subject, with novice medical students often experiencing difficulty grasping the intricate 3D spatial relationships. Most of the anatomical teaching in undergraduate medicine utilizes conventional 2D resources. E-learning technologies facilitate the development of learner-centered educational tools that can be tailored to meet each student's educational needs, and may foster improved learning in neuroanatomy, however this has yet to be examined fully in the literature. An interactive 3D e-learning module was developed to complement gross anatomy laboratory instruction. Incorporating such 3D modules may provide additional support for students in areas of anatomy that are spatially challenging, such as neuroanatomy. Specific anatomical structures and their relative spatial positions to other structures can be clearly defined in the 3D virtual environment from viewpoints that may not readily be available using cadaveric or 2D image modalities. Providing an interactive user interface for the 3D module in which the student controls many factors may enable the student to develop an improved understanding of the spatial relationships. This work outlines the process for the development of a 3D interactive module of the cerebral structures included in the anatomy curriculum for undergraduate medical students in their second year of study.

Recommendations for the development of e-modules for the continuing professional development of European dentists

NARCIS (Netherlands)

Kavadella, A.; Kossioni, A.E.; Tsiklakis, K.; Cowpe, J.; Bullock, A.; Barnes, E.; Bailey, S.; Thomas, H.; Thomas, R.; Karaharju-Suvanto, T.; Suomalainen, K.; Kersten, H.; Povel, E.; Giles, M.; Walmsley, D.; Soboleva, U.; Liepa, A.; Akota, I.

2013-01-01

Aims To provide evidence-based and peer-reviewed recommendations for the development of dental continuing professional development (CPD) learning e-modules. Methods The present recommendations are consensus recommendations of the DentCPD project team and were informed by a literature research,

Equipment development for automated assembly of solar modules

Science.gov (United States)

Hagerty, J. J.

1982-01-01

Prototype equipment was developed which allows for totally automated assembly in the three major areas of module manufacture: cell stringing, encapsulant layup and cure and edge sealing. The equipment is designed to be used in conjunction with a standard Unimate 2000B industrial robot although the design is adaptable to other transport systems.

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of building material integrated solar cell modules - modules with new multi-layer structure); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (shinfukuso kozo module))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Development is being made on a panel type module that can be used together with an air bubble concrete board (ALC board), and is provided with design characteristics. The development work includes trial fabrication and evaluation of a module with new multi-layer structure, and development of a technology to unitize cells and submodules, and a systematizing method. In the trial fabrication and evaluation, flame retardant and uninflammable modules using fluororesin, and modules with as large area as 4 m{sup 2} were fabricated on a trial basis, in addition to the modules with the basic structure. These modules were given evaluations on such wall material properties as wind pressure resistance, heat and cracking resistance, and fire resistance. In a deformation resistance test considering the integrated use with the ALC board, the developed modules showed a good result. In developing the cells with design characteristics, discussions were given on the inter-cell wiring methods. Development was made on a method to establish a unit structure based on the design and size of a building. In developing the systematization method, the trial fabrication method was applied to a module with lamination structure, a module integrated with the ALC board, and a large-area hollow module to have fabricated the top-light spandrels. (NEDO)

Development of whole core thermal-hydraulic analysis program ACT. 3. Coupling core module with primary heat transport system module

International Nuclear Information System (INIS)

Ohtaka, Masahiko; Ohshima, Hiroyuki

1998-10-01

A whole core thermal-hydraulic analysis program ACT is being developed for the purpose of evaluating detailed in-core thermal hydraulic phenomena of fast reactors including inter-wrapper flow under various reactor operation conditions. In this work, the core module as a main part of the ACT developed last year, which simulates thermal-hydraulics in the subassemblies and the inter-subassembly gaps, was coupled with an one dimensional plant system thermal-hydraulic analysis code LEDHER to simulate transients in the primary heat transport system and to give appropriate boundary conditions to the core model. The effective algorithm to couple these two calculation modules was developed, which required minimum modification of them. In order to couple these two calculation modules on the computing system, parallel computing technique using PVM (Parallel Virtual Machine) programming environment was applied. The code system was applied to analyze an out-of-pile sodium experiment simulating core with 7 subassemblies under transient condition for code verification. It was confirmed that the analytical results show a similar tendency of experimental results. (author)

Research and development of peripheral technology for photovoltaic power systems. Research and development of photovoltaic modules integrated with construction materials (detachable plane panel); Shuhen gijutsu no kenkyu kaihatsu. Kenzai ittaigata module no kenkyu kaihatsu (chakudatsushiki heiban panel)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of photovoltaic modules integrated with construction materials in fiscal 1994. (1) On development of technology for module structures, specifications of the horizontal muntin system module were newly determined in addition to the improved muntin system module, and the prototype pseudo-module integrated with construction material was prepared. The comparison results of the basic performance of both system modules clarified superior waterproofing and module temperature uniformity of the horizontal muntin system. Based on this specifications, integration technology of modules with back metal plates was studied. Formation of the integrated module close to final specifications was ascertained to be possible by use of passivation equipment to irregular form. (2) On development of construction and installation methods of modules, improvement of the waterproofing and workability of both system modules was studied. (3) On the study on practical use of modules, their design and ventilation/cooling structure were studied. 38 figs., 13 tabs.

Development of Hybrid Courses Utilizing Modules as an Objective in ATE Projects

Science.gov (United States)

Payne, James E.; Murphy, Richard M.; Payne, Linda L.

2017-01-01

Orangeburg-Calhoun Technical College (OCtech) has been awarded two National Science Foundation Advanced Technological Education (NSF-ATE) grants since 2011 that have the development of module-based hybrid courses in Engineering Technology and Mechatronics as objectives. In this article, the advantages and challenges associated with module-based…

Developing a service-learning module for oral health: A needs assessment

Directory of Open Access Journals (Sweden)

R Ebrahim

2017-03-01

Full Text Available Background. Service learning (SL as a pedagogy in higher education must be differentiated from other services with a primarily philanthropic intent. Dental therapy and oral hygiene students at Sefako Makgatho Health Sciences University, School of Oral Health Sciences, Pretoria, South Africa visit community sites during their 2nd year of study. However, the current curricula would need restructuring for alignment with the espoused pedagogy and standards of SL. Such an SL curriculum design would thus allow for the provision of meaningful services to communities as an integral component of these programmes. Objective. To explore (i perceptions of 2nd-year oral health students; and (ii opinions of academics with regard to the need for an SL module. Methods. Purposive sampling was used to conduct two focus group discussions with academics involved in curriculum development (n=11 and students who had previous exposure to communities (n=10. A survey containing open-ended questions was completed by 9 academics, who would implement the proposed SL module. Frequencies were calculated and data from the open questions were analysed for emergent themes. Results. Most academics (89%, n=8 indicated that working effectively with others as members of a team and developing cultural sensitivity were achievable from an SL module. Two themes emerged from the focus groups, i.e. (i enhanced teaching and learning – students could apply theoretical and clinical training in an authentic setting; and (ii standardisation of training – an SL module would ensure consistency when engaging with communities. Conclusion. The needs assessment was valuable to inform the development and implementation of the SL module.

Development and Impact Evaluation of an E-Learning Radiation Oncology Module

Energy Technology Data Exchange (ETDEWEB)

Alfieri, Joanne, E-mail: Joanne.alfieri@mail.mcgill.ca [Department of Radiation Oncology, McGill University Health Centre, Montreal, QC (Canada); Portelance, Lorraine; Souhami, Luis [Department of Radiation Oncology, McGill University Health Centre, Montreal, QC (Canada); Steinert, Yvonne; McLeod, Peter [Centre for Medical Education, McGill University, Montreal, QC (Canada); Gallant, Fleure [Department of Radiation Oncology, McGill University Health Centre, Montreal, QC (Canada); Artho, Giovanni [Department of Radiology, McGill University Health Centre, Montreal, QC (Canada)

2012-03-01

Purpose: Radiation oncologists are faced with the challenge of irradiating tumors to a curative dose while limiting toxicity to healthy surrounding tissues. This can be achieved only with superior knowledge of radiologic anatomy and treatment planning. Educational resources designed to meet these specific needs are lacking. A web-based interactive module designed to improve residents' knowledge and application of key anatomy concepts pertinent to radiotherapy treatment planning was developed, and its effectiveness was assessed. Methods and Materials: The module, based on gynecologic malignancies, was developed in collaboration with a multidisciplinary team of subject matter experts. Subsequently, a multi-centre randomized controlled study was conducted to test the module's effectiveness. Thirty-six radiation oncology residents participated in the study; 1920 were granted access to the module (intervention group), and 17 in the control group relied on traditional methods to acquire their knowledge. Pretests and posttests were administered to all participants. Statistical analysis was carried out using paired t test, analysis of variance, and post hoc tests. Results: The randomized control study revealed that the intervention group's pretest and posttest mean scores were 35% and 52%, respectively, and those of the control group were 37% and 42%, respectively. The mean improvement in test scores was 17% (p < 0.05) for the intervention group and 5% (p = not significant) for the control group. Retrospective pretest and posttest surveys showed a statistically significant change on all measured module objectives. Conclusions: The use of an interactive e-learning teaching module for radiation oncology is an effective method to improve the radiologic anatomy knowledge and treatment planning skills of radiation oncology residents.

Development and Impact Evaluation of an E-Learning Radiation Oncology Module

International Nuclear Information System (INIS)

Alfieri, Joanne; Portelance, Lorraine; Souhami, Luis; Steinert, Yvonne; McLeod, Peter; Gallant, Fleure; Artho, Giovanni

2012-01-01

Purpose: Radiation oncologists are faced with the challenge of irradiating tumors to a curative dose while limiting toxicity to healthy surrounding tissues. This can be achieved only with superior knowledge of radiologic anatomy and treatment planning. Educational resources designed to meet these specific needs are lacking. A web-based interactive module designed to improve residents' knowledge and application of key anatomy concepts pertinent to radiotherapy treatment planning was developed, and its effectiveness was assessed. Methods and Materials: The module, based on gynecologic malignancies, was developed in collaboration with a multidisciplinary team of subject matter experts. Subsequently, a multi-centre randomized controlled study was conducted to test the module's effectiveness. Thirty-six radiation oncology residents participated in the study; 1920 were granted access to the module (intervention group), and 17 in the control group relied on traditional methods to acquire their knowledge. Pretests and posttests were administered to all participants. Statistical analysis was carried out using paired t test, analysis of variance, and post hoc tests. Results: The randomized control study revealed that the intervention group's pretest and posttest mean scores were 35% and 52%, respectively, and those of the control group were 37% and 42%, respectively. The mean improvement in test scores was 17% (p < 0.05) for the intervention group and 5% (p = not significant) for the control group. Retrospective pretest and posttest surveys showed a statistically significant change on all measured module objectives. Conclusions: The use of an interactive e-learning teaching module for radiation oncology is an effective method to improve the radiologic anatomy knowledge and treatment planning skills of radiation oncology residents.

Development and validation of I x V curve tracer for photovoltaic modules

OpenAIRE

MÃrcio Leal Macedo Luna

2016-01-01

The IxV curves tracers for PV modules are used as a method of diagnosis of problems such as shadowing, faulty connections and degradation conditions. There are several types and brands tracers commercially available, but their costs are quite high in the Brazilian market due to the need to import. This thesis describes the development and validation of a IxV curve tracer for PV modules based on the electronic load method using MOSFET as load to the module. By appropriate variation of the MOSF...

Development and investigation of a CPV module with Cassegrain mirror optics

Science.gov (United States)

Dreger, Max; Wiesenfarth, Maike; Kisser, Arne; Schmid, Tobias; Bett, Andreas W.

2014-09-01

One approach to concentrate the sunlight in concentrating photovoltaic (CPV) modules is using Cassegrain mirror optics. The advantage is that a passively cooled solar cell can be mounted to a large heat spreader that does not shade the primary optics. In addition, the height of the module, hence weight, can be low. The design was selected on the basis of the results of a design study comparing different CPV module approaches presented in [1]. In this work, we present the development of a new prototype micro dish module. First results of the characterization are shown. Besides of the electrical performance, a machined optics and an injection molded was investigated regarding sensitivity to misalignment errors between the optical elements as well as measurement of the acceptance angle in- and outdoors. The machined optics was used as reference.

High Flux Heat Exchanger

Science.gov (United States)

1993-01-01

maximum jet velocity (6.36 m/s), and maximum number of jets (nine). Wadsworth and Mudawar [49] describe the use of a single slotted nozzle to provide...H00503 (ASME), pp. 121-128, 1989. 40 49. D. C. Wadsworth and I. Mudawar , "Cooling of a Multichip Electronic Module by Means of Confined Two-Dimensional...Jets of Dielectric Liquid," HTD-Vol. 111, Heat Transfer in Electrglif, Book No. H00503 (ASME), pp. 79-87, 1989. 50. D.C. Wadsworth and I. Mudawar

Classroom Modules for Nanotechnology Undergraduate Education: Development, Implementation and Evaluation

Science.gov (United States)

Shabani, R.; Massi, L.; Zhai, L.; Seal, S.; Cho, H. J.

2011-01-01

In order to address the challenges and restrictions given by a traditional classroom lecture environment, the top-down and bottom-up nanotechnology teaching modules were developed, implemented and evaluated. Then based on the hypothesis that instructors could further develop students' interest in this emerging area through the introduction of the…

EPICS IOC module development and implementation for the ISTTOK machine subsystem operation and control

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Paulo, E-mail: pricardofc@ipfn.ist.utl.pt [Associacao EURATOM/IST, Instituto de Plasmas e Fusao Nuclear-Laboratorio Associado, Instituto Superior Tecnico, P-1049-001 Lisboa (Portugal); Duarte, Andre; Pereira, Tiago; Carvalho, Bernardo; Sousa, Jorge; Fernandes, Horacio [Associacao EURATOM/IST, Instituto de Plasmas e Fusao Nuclear-Laboratorio Associado, Instituto Superior Tecnico, P-1049-001 Lisboa (Portugal); Correia, Carlos [Grupo de Electronica e Instrumentacao-Centro de Instrumentacao, Departamento de Fisica, Universidade de Coimbra, P-3004-516 Coimbra (Portugal); Goncalves, Bruno; Varandas, Carlos [Associacao EURATOM/IST, Instituto de Plasmas e Fusao Nuclear-Laboratorio Associado, Instituto Superior Tecnico, P-1049-001 Lisboa (Portugal)

2011-10-15

This paper presents a developed, tested and integrated EPICS IOC (I/O controller) module solution for the ISTTOK tokamak machine operation and control for the vacuum and gas injection systems. The work is organized in two software layers which communicate through a serial RS-232 communication protocol. The first software layer is an EPICS IOC module running as a computer server application capable of receiving requests from remote or local clients providing driver interface to the system by forwarding requested commands and receiving system and control operation status. The second software layer is the firmware running in Microchip dsPIC microcontroller modules which performs the interface from RS-232 optical fiber serial protocol to EPICS IOC module. The dsPIC module communicates to the ISTTOK tokamak sensors and actuators via RS-485 and is programmed with a new protocol developed for this purpose that allows EPICS IOC module command sending/receiving, machine operation control and monitoring and system status information. Communication between EPICS IOC module and clients is achieved via a TCP/IP and UDP protocol referred as Channel Access. In addition, the EPICS IOC module provides user client applications access allowing operators to perform remote or local monitoring, operation and control.

Design and development of line type modulators for high impedance electron gun

Energy Technology Data Exchange (ETDEWEB)

Dixit, Kavita P.; Tillu, Abhijit; Chavan, Ramchandra; Yadav, Vivek; Sarukte, Hemant, E-mail: kavidi@barc.gov.in [Accelerator and Pulse Power Division, Bhabha Atomic Research Centre, Mumbai (India)

2014-07-01

Conventional line type modulators are routinely used for powering pulsed power microwave devices such as magnetrons and klystrons used for radar, medical and scientific applications. The load impedance (operating point) is fairly well defined in these cases, and makes the design of the discharging circuit of the modulator straight forward. This paper describes the Line type modulators that have been developed and being routinely used for powering the Triode Electron Gun of industrial electron linacs. The beam parameters of such guns are user defined and the pulse current varies from few mA to 800mA (typ). The beam energies requirement varies from 40 keV to 80 keV. Hence the impedance offered by the electron gun to the power source (modulator) is not well defined. The load capacitance which is inclusive of the various stray capacitances along with the intrinsic gun capacitance is ∼ 200-400 pF. This capacitance, which depends on the configuration, shunts the load and makes the effective load highly capacitive with the resistive part varying over a wide range. The paper describes the design and development of conventional line type modulators for powering Electron gun load of the type described above. (author)

Developing Media Module Proposed to Editor in Editorial Division

Science.gov (United States)

Kristanto, A.; Mustaji; Mariono, A.; Sulistiowati; Nuryati, D. W.

2018-01-01

In this era of technology in Indonesia, various publishers introduce themselves and participate in advancing the quality of education through the publication of various books as the learning sources. One of the publishers is PT. JP Press. In compiling the learning sources, we found some problems that are left unresolved by the editor. The purpose of this research is to overcome the problems that exist in PT. JP Press by developing media module. This development research uses the ADDIE model. The types of data used in this study are qualitative and quantitative data obtained based on the results of structured interviews with material experts and media experts, as well as the editorial response questionnaire provided for individual try-out and small group try-out. Therefore, it can be concluded that the medium of elementary school supplementary module proposed to the editors of PT. JP Press is valuable to be used in the teaching and learning activities.

Development of a NIM module for time-to-digital conversion

International Nuclear Information System (INIS)

Lin Yanchang; Wang Xiaobin; Chen Shaomin; Gao Yuanning; Jiang Chunhua; Qian Wenbin

2008-01-01

A developed single slot wide NIM module for time-to-digital conversion (TDC) is presented in this paper. This TDC module consists of a CPLD based double edge trigger counter with logic function circuit, a high speed comparator based NIM-to-TTL logic level converter, a processor ARM based data access and communication control unit, and voltage regulators for power supply. There are two input groups available, separately for accepting start and stop signal between two input ports or just from the same input port in sequence. With a 50 MHz reference clock, the available input ranges from 0 to 81.91 μs, and the resolution can reach 10 ns level. This module was tested in a muon lifetime measurement experiment, showing good linearity, simple configuration, low power consumption, good reliability, low cost, and easy upgrade as well. (authors)

Development and application of visual support module for remote operator in 3D virtual environment

International Nuclear Information System (INIS)

Choi, Kyung Hyun; Cho, Soo Jeong; Yang, Kyung Boo; Bae, Chang Hyun

2006-02-01

In this research, the 3D graphic environment was developed for remote operation, and included the visual support module. The real operation environment was built by employing a experiment robot, and also the identical virtual model was developed. The well-designed virtual models can be used to retrieve the necessary conditions for developing the devices and processes. The integration of 3D virtual models, the experimental operation environment, and the visual support module was used for evaluating the operation efficiency and accuracy by applying different methods such as only monitor image and with visual support module

Development and application of visual support module for remote operator in 3D virtual environment

Energy Technology Data Exchange (ETDEWEB)

Choi, Kyung Hyun; Cho, Soo Jeong; Yang, Kyung Boo [Cheju Nat. Univ., Jeju (Korea, Republic of); Bae, Chang Hyun [Pusan Nat. Univ., Busan (Korea, Republic of)

2006-02-15

In this research, the 3D graphic environment was developed for remote operation, and included the visual support module. The real operation environment was built by employing a experiment robot, and also the identical virtual model was developed. The well-designed virtual models can be used to retrieve the necessary conditions for developing the devices and processes. The integration of 3D virtual models, the experimental operation environment, and the visual support module was used for evaluating the operation efficiency and accuracy by applying different methods such as only monitor image and with visual support module.

Development of a 3 tesla - 10 Hz pulsed magnet-modulator system

International Nuclear Information System (INIS)

Krausse, G.J.; Butterfield, K.B.

1984-01-01

In order to support the experimental work done at the Los Alamos Meson Physics Facility new instrumentation and data collection systems of advanced design are developed on a regular basis. Within the instrumentation system for an experiment at LAMPF, The Photo-Excitation of the H - Ion Resonances, there exists a need for a pulsed air-core electromagnet and modulator system. The magnet must be capable of producing a field strength of 0 to 3T in a volume of 3.5 cm 3 . In addition it must be radiation resistant, have a uniform field, operate in a high vacuum with little or no outgassing, and the physical layout of the magnet must provide minimal azimuthal obstruction to both the ion and laser beams. The modulator must be capable of producing up to a 15KA pulse with duration of two μs at a maximum repetition rate of 10 Hz. Modulator layout must be extremely reliable so that data collection time is not lost during the experiment. This paper describes in detail the development of the system

Development of core thermal-hydraulics module for intelligent reactor design system (IRDS)

International Nuclear Information System (INIS)

Kugo, Teruhiko; Nakagawa, Masayuki; Fujii, Sadao.

1994-08-01

We have developed an innovative reactor core thermal-hydraulics module where a designer can easily and efficiently evaluate his design concept of a new type reactor in the thermal-hydraulics field. The main purpose of this module is to decide a feasible range of basic design parameters of a reactor core in a conceptual design stage of a new type reactor. The module is to be implemented in Intelligent Reactor Design System (IRDS). The module has the following characteristics; 1) to deal with several reactor types, 2) four thermal hydraulics and fuel behavior analysis codes are installed to treat different type of reactors and design detail, 3) to follow flexibly modification of a reactor concept, 4) to provide analysis results in an understandable way so that a designer can easily evaluate feasibility of his concept, and so on. The module runs on an engineering workstation (EWS) and has a user-friendly man-machine interface on a pre- and post-processing. And it is equipped with a function to search a feasible range called as Design Window, for two design parameters by artificial intelligence (AI) technique and knowledge engineering. In this report, structure, guidance for users of an usage of the module and instruction of input data for analysis modules are presented. (author)

Development of a Precise Polarization Modulator for UV Spectropolarimetry

Science.gov (United States)

Ishikawa, S.; Shimizu, T.; Kano, R.; Bando, T.; Ishikawa, R.; Giono, G.; Tsuneta, S.; Nakayama, S.; Tajima, T.

2015-10-01

We developed a polarization modulation unit (PMU) to rotate a waveplate continuously in order to observe solar magnetic fields by spectropolarimetry. The non-uniformity of the PMU rotation may cause errors in the measurement of the degree of linear polarization (scale error) and its angle (crosstalk between Stokes-Q and -U), although it does not cause an artificial linear polarization signal (spurious polarization). We rotated a waveplate with the PMU to obtain a polarization modulation curve and estimated the scale error and crosstalk caused by the rotation non-uniformity. The estimated scale error and crosstalk were {PMU will be used as a waveplate motor for the Chromospheric Lyman-Alpha SpectroPolarimeter (CLASP) rocket experiment. We confirm that the PMU performs and functions sufficiently well for CLASP.

Multidisciplinary Modelling Tools for Power Electronic Circuits

DEFF Research Database (Denmark)

Bahman, Amir Sajjad

in reliability assessment of power modules, a three-dimensional lumped thermal network is proposed to be used for fast, accurate and detailed temperature estimation of power module in dynamic operation and different boundary conditions. Since an important issue in the reliability of power electronics...... environment to be used for optimization of cooling system layout with respect to thermal resistance and pressure drop reductions. Finally extraction of electrical parasitics in the multi-chip power modules will be investigated. As the switching frequency of power devices increases, the size of passive...... components are reduced considerably that leads to increase of power density and cost reduction. However, electrical parasitics become more challenging with increasing the switching frequency and paralleled chips in the integrated and denser packages. Therefore, electrical parasitic models are analyzed based...

Development of Modal Aerosol Module in CAM5 for Biogeochemical Cycles

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiaohong [Univ. of Wyoming, Laramie, WY (United States)

2017-11-18

This project aims at developing new capabilities for the Modal Aerosol Module in the DOE’s E3SM model with the applications to the global biogeochemical cycle. The impacts of the new developments on model simulations of clouds and climate will be examined. There are thee objectives for this project study: Implementing primary marine organic aerosols into the modal aerosol module (MAM) and investigate effects of primary marine organic aerosols on climate in E3SM; Implementing dust speciation in MAM and investigate the effect of dust species on mixed-phase clouds through indirect effects in E3SM; Writing papers documenting the new MAM developments (e.g., MAM4 documentation paper, marine organic aerosol paper, dust speciation); These objectives will be accomplished in collaborations with Drs. Phil Rasch, Steve Ghan, and Susannah Burrows at Pacific Northwest National Laboratory.

Development of conductor feedthrough module of LV electrical penetration assembly for research reactors

International Nuclear Information System (INIS)

Luo Zhiyuan; Wang Guangjin; Zhou Bin

2007-01-01

A LV electrical penetration assembly with perfusion sealing conductor feedthrough module was developed, which can be used for the connection of internal and external cables through the wall of the research reactor workshop. The LV electrical penetration assembly was combined with several independent modules. The maintenance and replacement of the assembly can be easily done in service. The sealing of conductor feedthrough module was achieved with the perfusion of self-extinguishing epoxy. The leakage between the conductor feedthrough module and the end plate module was blocked with rubber rings. The result of the leakage test and the electrical performance test for the samples of conductor feedthrough module satisfied the requirement of research reactor. The structure of the new electrical penetration assembly is simple and compact. It can be manufactured with mature technology and cost low price. The performance of the assembly is steady. It can be used widely in research reactors. (authors)

Retinoic acid modulates chondrogenesis in the developing mouse cranial base.

Science.gov (United States)

Kwon, Hyuk-Jae; Shin, Jeong-Oh; Lee, Jong-Min; Cho, Kyoung-Won; Lee, Min-Jung; Cho, Sung-Won; Jung, Han-Sung

2011-12-15

The retinoic acid (RA) signaling pathway is known to play important roles during craniofacial development and skeletogenesis. However, the specific mechanism involving RA in cranial base development has not yet been clearly described. This study investigated how RA modulates endochondral bone development of the cranial base by monitoring the RA receptor RARγ, BMP4, and markers of proliferation, programmed cell death, chondrogenesis, and osteogenesis. We first examined the dynamic morphological and molecular changes in the sphenooccipital synchondrosis-forming region in the mouse embryo cranial bases at E12-E16. In vitro organ cultures employing beads soaked in RA and retinoid-signaling inhibitor citral were compared. In the RA study, the sphenooccipital synchondrosis showed reduced cartilage matrix and lower BMP4 expression while hypertrophic chondrocytes were replaced with proliferating chondrocytes. Retardation of chondrocyte hypertrophy was exhibited in citral-treated specimens, while BMP4 expression was slightly increased and programmed cell death was induced within the sphenooccipital synchondrosis. Our results demonstrate that RA modulates chondrocytes to proliferate, differentiate, or undergo programmed cell death during endochondral bone formation in the developing cranial base. Copyright © 2011 Wiley Periodicals, Inc., A Wiley Company.

Development of a diagnostic system for Klystron modulators using a neural network

International Nuclear Information System (INIS)

Mutoh, M.; Oonuma, T.; Shibasaki, Y.; Abe, I.; Nakahara, K.

1992-01-01

The diagnostic system for klystron modulators using a neural network has been developed. Large changes in the voltage and current of the main circuit in a klystron modulator were observed just several ten milli-seconds before the modulator experienced trouble. These changes formed a peculiar pattern that depended on the parts with problems. Diagnosis was possible by means of pattern recognition. The recognition test of patterns using a neutral network has shown good results. This system, which is built in a linac control system, is presently being operated so as to collect new trouble patterns and to carry out tests for practical use. (author)

Cell module and fuel conditioner development

Science.gov (United States)

Hoover, D. Q., Jr.

1980-01-01

Components for the first 5 cell stack (no cooling plates) of the MK-2 design were fabricated. Preliminary specfications and designs for the components of a 23 cell MK-1 stack with four DIGAS cooling plates were developed. The MK-2 was selected as a bench mark design and a preliminary design of the facilities required for high rate manufacture of fuel cell modules was developed. Two stands for testing 5 cell stacks were built and design work for modifying existing stands and building new stands for 23 and 80 cell stacks was initiated. Design and procurement of components and materials for the catalyst test stand were completed and construction initiated. Work on the specifications of pipeline gas, tap water and recovered water and definition of equipment required for treatment was initiated. An innovative geometry for the reformer was conceived and modifications of the computer program to be used in its design were stated.

Development of 700 pps high-duty-cycle line-type pulse modulator

Energy Technology Data Exchange (ETDEWEB)

Baba, H.; Satoh, K.; Miura, A. [NIHON KOSHUHA Co., LTD., Yokohama, Kanagawa (Japan)] [and others

1997-04-01

The high-duty-cycle line-type pulse modulator has been developed to drive the 5.5 MW S-band klystron at the 700 pps maximum repetition-rate and the 14 {mu}sec flat-top pulse-width. To keep an enough recovery time to the thyratron-tube, the command charging scheme was adopted. To do this, a charging SCR-bank has been developed, which is capable of handling the peak charging current of 50 A. The system achieved the world wide highest average output-power of 205 kW. Two modulators have been installed in a new high-duty-cycle electron linear accelerator, which has been started its business operation in March 1996 as an electron-beam-sterilization facility. (J.P.N)

Seed-vectored endophytic bacteria modulate development of rice seedlings.

Science.gov (United States)

Verma, S K; Kingsley, K; Irizarry, I; Bergen, M; Kharwar, R N; White, J F

2017-06-01

The aim of the present study was to evaluate the effects of the removal of indigenous bacteria from rice seeds on seedling growth and development. Here we report the presence of three indigenous endophytic bacteria in rice seeds that play important roles in modulating seedling development (shoot and root lengths, and formation of root hairs and secondary roots) and defence against pathogens. Seed-associated bacteria were removed using surface sterilization with NaOCl (bleach) followed by antibiotic treatment. When bacteria were absent, growth of seedlings in terms of root hair development and overall seedling size was less than that of seedlings that contained bacteria. Reactive oxygen staining of seedlings showed that endophytic bacteria became intracellular in root parenchyma cells and root hairs. Roots containing endophytic bacteria were seen to stain densely for reactive oxygen, while roots free of bacteria stained lightly for reactive oxygen. Bacteria were isolated and identified as Enterobacter asburiae (VWB1), Pantoea dispersa (VWB2) and Pseudomonas putida (VWB3) by 16S rDNA sequencing. Bacteria were found to produce indole acetic acid (auxins), inhibited the pathogen Fusarium oxysporum and solubilized phosphate. Reinoculation of bacteria onto seedlings derived from surface-disinfected rice and Bermuda grass seeds significantly restored seedling growth and development. Rice seeds harbour indigenous bacterial endophytes that greatly influence seedling growth and development, including root and shoot lengths, root hair formation and disease susceptibility of rice seedlings. This study shows that seeds of rice naturally harbour bacterial endophytes that play key roles in modulation of seedling development. © 2017 The Society for Applied Microbiology.

Development of a compact 25-channel preamplifier module for Si-pad detectors of the BARC-CPDA

International Nuclear Information System (INIS)

Inkar, A.; John, Bency; Vind, R.P.; Kinage, L.; Jangale, R.V.; Biswas, D.C.; Nayak, B.K.

2011-01-01

The BARC Charged Particle Detector Array modules use indigenously developed Si pad detectors as their first element. Total number of charge sensitive pre-amplifiers required for the Si-pad detectors is 250. One of the main ideas here is a layout of five pre-amplifiers connected with one Si-pad detector (called a bank of preamplifiers). In the present work, a 25-channel pre-amplifier module that can cater to 5 independent Si-pad detectors, or a five-bank module, has been developed. This module uses pre-amp hybrid chips A1422H from CAEN S.p.A. and is housed in a double width NIM standard box. The module has been tested for performance using proton and ''7Li beams from FOTIA facility, Trombay

Fast Convolution Module (Fast Convolution Module)

National Research Council Canada - National Science Library

Bierens, L

1997-01-01

This report describes the design and realisation of a real-time range azimuth compression module, the so-called 'Fast Convolution Module', based on the fast convolution algorithm developed at TNO-FEL...

Identifying the 'right' supplier for module developments-a cross-industrial case analysis

NARCIS (Netherlands)

Eggers, Justus Erich; Hofman, Erwin; Schiele, Holger; Holschbach, Elmar

2017-01-01

Relational view argues that buying companies should integrate supplier resources in new product development (NPD) projects to realise competitive advantages. Due to decoupling of modules and the associated opportunity to allocate development activities to upstream suppliers, modular product

Development of ultracapacitor modules for 42-V automotive electrical systems

Science.gov (United States)

Jung, Do Yang; Kim, Young Ho; Kim, Sun Wook; Lee, Suck-Hyun

Two types of ultracapacitor modules have been developed for use as energy-storage devices for 42-V systems in automobiles. The modules show high performance and good reliability in terms of discharge and recharge capability, long-term endurance, and high energy and power. During a 42-V system simulation test of 6-kW power boosting/regenerative braking, the modules demonstrate very good performance. In high-power applications such as 42-V and hybrid vehicle systems, ultracapacitors have many merits compared with batteries, especially with respect to specific power at high rate, thermal stability, charge-discharge efficiency, and cycle-life. Ultracapacitors are also very safe, reliable and environmentally friendly. The cost of ultracapacitors is still high compared with batteries because of the low production scale, but is decreasing very rapidly. It is estimated that the cost of ultracapacitors will decrease to US$ 300 per 42-V module in the near future. Also, the maintenance cost of the ultracapacitor is nearly zero because of its high cycle-life. Therefore, the combined cost of the capacitor and maintenance will be lower than that of batteries in the near future. Overall, comparing performance, price and other parameters of ultracapacitors with batteries, ultracapacitors are the most likely candidate for energy-storage in 42-V systems.

DEVELOPMENT OF A LOW COST INFERENTIAL NATURAL GAS ENERGY FLOW RATE PROTOTYPE RETROFIT MODULE

Energy Technology Data Exchange (ETDEWEB)

E. Kelner; D. George; T. Morrow; T. Owen; M. Nored; R. Burkey; A. Minachi

2005-05-01

In 1998, Southwest Research Institute began a multi-year project to develop a working prototype instrument module for natural gas energy measurement. The module will be used to retrofit a natural gas custody transfer flow meter for energy measurement, at a cost an order of magnitude lower than a gas chromatograph. Development and evaluation of the prototype energy meter in 2002-2003 included: (1) refinement of the algorithm used to infer properties of the natural gas stream, such as heating value; (2) evaluation of potential sensing technologies for nitrogen content, improvements in carbon dioxide measurements, and improvements in ultrasonic measurement technology and signal processing for improved speed of sound measurements; (3) design, fabrication and testing of a new prototype energy meter module incorporating these algorithm and sensor refinements; and (4) laboratory and field performance tests of the original and modified energy meter modules. Field tests of the original energy meter module have provided results in close agreement with an onsite gas chromatograph. The original algorithm has also been tested at a field site as a stand-alone application using measurements from in situ instruments, and has demonstrated its usefulness as a diagnostic tool. The algorithm has been revised to use measurement technologies existing in the module to measure the gas stream at multiple states and infer nitrogen content. The instrumentation module has also been modified to incorporate recent improvements in CO{sub 2} and sound speed sensing technology. Laboratory testing of the upgraded module has identified additional testing needed to attain the target accuracy in sound speed measurements and heating value.

Electronics cooling of Phenix multiplicity and vertex detector

International Nuclear Information System (INIS)

Chen, Z.; Gregory, W.S.

1996-08-01

The Multiplicity and Vertex Detector (MVD) uses silicon strip sensors arranged in two concentric barrels around the beam pipe of the PHENIX detector that will be installed at Brookhaven National Laboratory. Each silicon sensor is connected by a flexible kapton cable to its own front-end electronics printed circuit board that is a multi-chip module or MCM. The MCMs are the main heat source in the system. To maintain the MVD at optimized operational status, the maximum temperature of the multi-chip modules must be below 40 C. Using COSMOS/M HSTAR for the Heat Transfer analysis, a finite element model of a typical MCM plate was created to simulate a 9m/s airflow and 9m/s mixed flow composed of 50% helium and 50% air respectively, with convective heat transfer on both sides of the plate. The results using a mixed flow of helium and air show that the average maximum temperature reached by the MCMs is 37.5 C. The maximum temperature which is represented by the hot spots on the MCM is 39.43 C for the helium and air mixture which meets the design temperature requirement 40 C. To maintain the Multiplicity and Vertex Detector at optimized operational status, the configuration of the plenum chamber, the power dissipated by the silicon chips, the fluid flow velocity and comparison on the MCM design parameters will be discussed

Design and development of a work robot to place ATLAS SCT modules onto barrel cylinders

International Nuclear Information System (INIS)

Terada, S.; Kobayashi, H.; Sengoku, H.; Kato, Y.; Hara, K.; Honma, F.; Ikegami, Y.; Iwata, Y.; Kohriki, T.; Kondo, T.; Nakano, I.; Takashima, R.; Tanaka, R.; Ujiie, N.; Unno, Y.; Yasuda, S.

2005-01-01

More than 2000 silicon modules need to be placed and fastened on the ATLAS SCT barrel tracker. A semi-automatic pick-and-place work robot was designed and developed to cope with the module placement for the SCT barrel assembly. We found that this robot could place modules to a mechanical precision of better than 25 μm

Design and development of a work robot to place ATLAS SCT modules onto barrel cylinders

CERN Document Server

Terada, S; Honma, F; Ikegami, Y; Iwata, Y; Kato, Y; Kobayashi, H; Kohriki, T; Kondo, T; Nakano, I; Sengoku, H; Takashima, R; Tanaka, R; Ujiie, N; Unno, Y; Yasuda, S

2005-01-01

More than 2000 silicon modules need to be placed and fastened on the ATLAS SCT barrel tracker. A semi-automatic pick-and-place work robot was designed and developed to cope with the module placement for the SCT barrel assembly. We found that this robot could place modules to a mechanical precision of better than 25 mum.

A Pc-interface module has been developed that provides an easy way to interface PC

International Nuclear Information System (INIS)

Rifai, Ahmad; Gunawan, Usep Setia

2003-01-01

A pc-interface module has been developed that provides an easy way to interface PC with I/O devices. This MSC51 micro controller based module accepts series of commands from a personal computer through a serial port. The commands are defined to easily control 24 I/O lines available on the module. These lines can be individually used as either input or output that make the module very verstile. A command is received by the module on ASCII string basis. Each character sent to the module will give an interrupt. The firmware's interrupt handler will store the character in a buffer until end of command character arrives. The firmware then parses and interpreters the command and responses accordingly

Development of thin-film Si HYBRID solar module

Energy Technology Data Exchange (ETDEWEB)

Nakajima, Akihiko; Gotoh, Masahiro; Sawada, Toru; Fukuda, Susumu; Yoshimi, Masashi; Yamamoto, Kenji; Nomura, Takuji [Kaneka Corporation, 2-1-1, Hieitsuji, Otsu, Shiga 520-0104 (Japan)

2009-06-15

The device current-voltage (I-V) characteristics of thin-film silicon stacked tandem solar modules (HYBRID modules), consisting of a hydrogenated amorphous silicon (a-Si:H) cell and a thin-film crystalline silicon solar cell ({mu}c-Si), have been investigated under various spectral irradiance distributions. The performance of the HYBRID module varied periodically in natural sunlight due to the current-limiting property of the HYBRID module and the environmental effects. The behavior based on the current-limiting property was demonstrated by the modelling of the I-V curves using the linear interpolation method for each component cell. The improvement of the performance for the HYBRID module in natural sunlight will also be discussed from the viewpoint of the device design of the component cells. (author)

Photovoltaic module certification/laboratory accreditation criteria development

Energy Technology Data Exchange (ETDEWEB)

Osterwald, C.R. [National Renewable Energy Lab., Golden, CO (United States); Hammond, R.L.; Wood, B.D.; Backus, C.E.; Sears, R.L. [Arizona State Univ., Tempe, AZ (United States); Zerlaut, G.A. [SC-International Inc., Phoenix, AZ (United States); D`Aiello, R.V. [RD Associates, Tempe, AZ (United States)

1995-04-01

This document provides an overview of the structure and function of typical product certification/laboratory accreditation programs. The overview is followed by a model program which could serve as the basis for a photovoltaic (PV) module certification/laboratory accreditation program. The model covers quality assurance procedures for the testing laboratory and manufacturer, third-party certification and labeling, and testing requirements (performance and reliability). A 30-member Criteria Development Committee was established to guide, review, and reach a majority consensus regarding criteria for a PV certification/laboratory accreditation program. Committee members represented PV manufacturers, end users, standards and codes organizations, and testing laboratories.

Development of volume rendering module for real-time visualization system

International Nuclear Information System (INIS)

Otani, Takayuki; Muramatsu, Kazuhiro

2000-03-01

Volume rendering is a method to visualize the distribution of physical quantities in the three dimensional space from any viewpoint by tracing the ray direction on the ordinary two dimensional monitoring display. It enables to provide the interior information as well as the surfacial one by producing the translucent images. Therefore, it is regarded as a very useful means as well as an important one in the analysis of the computational results of the scientific calculations, although it has, unfortunately, disadvantage to need a large amount of computing time. This report describes algorithm and its performance of the volume rendering soft-ware which was developed as an important functional module in the real-time visualization system PATRAS. This module can directly visualize the computed results on BFC grid. Moreover, it has already realized the speed-up in some parts of the software by the use of a newly developed heuristic technique. This report includes the investigation on the speed-up of the software by parallel processing. (author)

The development and preliminary testing of a multimedia patient–provider survivorship communication module for breast cancer survivors

Science.gov (United States)

Wen, Kuang-Yi; Miller, Suzanne M.; Stanton, Annette L.; Fleisher, Linda; Morra, Marion E.; Jorge, Alexandra; Diefenbach, Michael A.; Ropka, Mary E.; Marcus, Alfred C.

2012-01-01

Objective This paper describes the development of a theory-guided and evidence-based multimedia training module to facilitate breast cancer survivors’ preparedness for effective communication with their health care providers after active treatment. Methods The iterative developmental process used included: (1) theory and evidence-based content development and vetting; (2) user testing; (3) usability testing; and (4) participant module utilization. Results Formative evaluation of the training module prototype occurred through user testing (n = 12), resulting in modification of the content and layout. Usability testing (n = 10) was employed to improve module functionality. Preliminary web usage data (n = 256, mean age = 53, 94.5% White, 75% college graduate and above) showed that 59% of the participants accessed the communication module, for an average of 7 min per login. Conclusion The iterative developmental process was informative in enhancing the relevance of the communication module. Preliminary web usage results demonstrate the potential feasibility of such a program. Practice implications Our study demonstrates survivors’ openness to the use of a web-based communication skills training module and outlines a systematic iterative user and interface program development and testing process, which can serve as a prototype for others considering such an approach. PMID:22770812

The development and preliminary testing of a multimedia patient-provider survivorship communication module for breast cancer survivors.

Science.gov (United States)

Wen, Kuang-Yi; Miller, Suzanne M; Stanton, Annette L; Fleisher, Linda; Morra, Marion E; Jorge, Alexandra; Diefenbach, Michael A; Ropka, Mary E; Marcus, Alfred C

2012-08-01

This paper describes the development of a theory-guided and evidence-based multimedia training module to facilitate breast cancer survivors' preparedness for effective communication with their health care providers after active treatment. The iterative developmental process used included: (1) theory and evidence-based content development and vetting; (2) user testing; (3) usability testing; and (4) participant module utilization. Formative evaluation of the training module prototype occurred through user testing (n = 12), resulting in modification of the content and layout. Usability testing (n = 10) was employed to improve module functionality. Preliminary web usage data (n = 256, mean age = 53, 94.5% White, 75% college graduate and above) showed that 59% of the participants accessed the communication module, for an average of 7 min per login. The iterative developmental process was informative in enhancing the relevance of the communication module. Preliminary web usage results demonstrate the potential feasibility of such a program. Our study demonstrates survivors' openness to the use of a web-based communication skills training module and outlines a systematic iterative user and interface program development and testing process, which can serve as a prototype for others considering such an approach. Copyright © 2012. Published by Elsevier Ireland Ltd.

Evaluation of a Team Project Based Learning Module for Developing Employability Skills

OpenAIRE

Janice Whatley

2012-01-01

This paper presents a case study, in which a new module, aimed at enhancing students’ employ-ability skills, is evaluated. Employability skills for graduates from higher education are regarded as essential outcomes from their degree programmes, but it can be difficult to provide appropriate opportunities to develop these skills in the context of their studies. This paper describes a new module, called Live Projects, designed to provide project based learning on campus, but involv-ing local bu...

Developing the fun and educative module in plant morphology and anatomy learning for tenth graders

Directory of Open Access Journals (Sweden)

Alfi Suciyati

2018-03-01

Full Text Available This research aims to examine the eligibility of and responses from expert media, expert material, practitioners and students’ on the ‘Fun and Educative’ biology module. The module was developed in a fun and educative way presenting various educative games. The research development model is using ADDIE model that consists of five phases: Analysis, Design, Development, Implementation, and Evaluation. The data collection technique employed examination of learning media experts, material experts, practitioners (biology teachers, and students. The data of research was analyzed in descriptive-qualitative and descriptive-qualitative ways. The results of evaluation on the module’s eligibility convey that the learning media expert gave 87.69% with the category of ‘highly eligible’, the material expert gave 86.00% with the category of ‘highly eligible', and the practitioners gave 83.68% with the category of ‘eligible'. The students' responses to questionnaires given related to the developed module gave 90.00% with the category of ‘highly interesting'. Based on the results of examination by the media expert, material expert, practitioners, and students, conclude that the module has fulfilled the criteria of good and eligible learning material and can be used for studying biology.

Intensity Modulated Radiation Therapy. Development of the technique

International Nuclear Information System (INIS)

Rafailovici, L.; Alva, R.; Chiozza, J.; Donato, H.; Falomo, S.; Cardiello, C.; Furia, O.; Martinez, A.; Filomia, M.L.; Sansogne, R.; Arbiser, S.; Dosoretz, B.

2008-01-01

Full text: Introduction: Intensity Modulated Radiation Therapy (IMRT) is a result of advances in computer sciences that allowed the development of new technology related to planning and radiation therapy. IMRT was developed to homogenize the dose in the target volumes and decrease the dose in the surrounding healthy tissue. Using a software with high calculation capacity a simultaneous irradiation with different doses in a given volume is achieved. IMRT is based on internal planning. Material and methods: 628 patients were treated with IMRT in prostate lesions, head and neck, breast, thorax, abdomen and brain since August 2008. The software for IMRT is the XIO CMS and the accelerator used is a Varian Clinac 6 / 100. IMRT requires a first simulation, where immobilization systems are selected (mats, thermoplastic masks, among others) and the demarcation of the target structures, healthy tissue and dose prescription by a tattoo. Images of CT / MRI are merged when necessary. Once the system made the treatment optimization, this one is regulated by modulators. These are produced by numerical control machines from digital files produced by software. In a second modulation the planned irradiation is checked and tattoo is carried out according with this. We have a strict process of quality assurance to assess the viability of the plan before its implementation. We use the Map Check it possible to compare the dose on the central axis and the distribution in the whole plane regarding to that generated by the planning system. From 03/2008 the virtual simulation process was implemented integrating the described stages. Results and Conclusions: IMRT is a complex technique. The meticulous planning, implementation of process and quality control allows the use of this technique in a reliable and secure way. With IMRT we achieved a high level of dose conformation, less irradiation of healthy tissue, lower rates of complications and the dose escalation for some tumors. (authors) [es

Development of contextual teaching and learning based science module for junior high school for increasing creativity of students

Science.gov (United States)

Kurniasari, H.; Sukarmin; Sarwanto

2018-03-01

The purpose of this research are to analyze the the properness of contextual teaching and learning (CTL)-based science module for Junior High School for increasing students’ creativity and using CTL-based science module to increase students’ learning creativity. Development of CTL-based science module for Junior High School is Research and Development (R&D) using 4D Model consist of 4 steps: define, design, develop, and disseminate. Module is validated by 3 expert validators (Material, media, and language experts), 2 reviewer and 1 peer reviewer. . Based on the results of data analysis, it can be concluded that: the results of the validation, the average score of CTL-based science module is 88.28%, the value exceeded the value of the cut off score of 87.5%, so the media declared eligible for the study. Research shows that the gain creativity class that uses CTL-based science module has a gain of 0.72. Based on the results of the study showed that CTL-based science module effectively promotes creativity of students

Development of module-based simulation system for nuclear power plant

International Nuclear Information System (INIS)

Yoshikawa, H.

1990-01-01

Module-based Simulation System (MSS) has been developed to realize a new software environment enabling versatile dynamic simulation of a complex nuclear power plant system flexibly. Described in the paper are (i) fundamental methods utilized in MMS and its software systemization, (ii) development of human interface system to help users in generating integrated simulation programs automatically, and (iii) development of an intelligent user support system for helping users in the two phases of automatical semantic diagnosis and consultation to automatic input data setup for the MSS-generated programs

Broadening Student Perspectives on Marketing Research Ethics: Development and Applications of a Teaching Module

Science.gov (United States)

Handlin, Amy

2012-01-01

This paper describes an ethics module developed by the author to engage marketing research students during the fall semester, when they are bombarded by political polls. The module matches ethically questionable polling practices to similarly troubling practices in marketing research. The goals are to show that ethical principles are not topic- or…

Development Modules for Specification of Requirements for a System of Verification of Parallel Algorithms

Directory of Open Access Journals (Sweden)

Vasiliy Yu. Meltsov

2012-05-01

Full Text Available This paper presents the results of the development of one of the modules of the system verification of parallel algorithms that are used to verify the inference engine. This module is designed to build the specification requirements, the feasibility of which on the algorithm is necessary to prove (test.

Development of an Ethernet enabled microcontroller based module for Superconducting Cyclotron ECR beam line control

International Nuclear Information System (INIS)

Chatterjee, M.; Koley, D.; Nabhiraj, P.Y.

2012-01-01

An Ethernet enabled control and data acquisition module is developed for remote control and monitoring of the ECR beam line equipment of the Superconducting Cyclotron. The PIC microcontroller based module supports multiple general purpose analog and digital inputs and outputs for interfacing with various equipments and an embedded web server. The remote monitoring and control of the equipment are achieved through the web based user interface. The user authenticated access to control parameters and module configuration parameters ensures the operational safety of the equipment under control. This module is installed in Superconducting Cyclotron ECR beam line for the control and monitoring of vacuum pumping modules, comprising of pumps, gate valves and dual vacuum gauges. The installation of these modules results in a distributed control with localised field cabling and hence better fault diagnosis. (author)

Decoupled Modulation Control

Energy Technology Data Exchange (ETDEWEB)

Wang, Shaobu; Huang, Renke; Huang, Zhenyu; Diao, Ruisheng

2016-06-03

The objective of this research work is to develop decoupled modulation control methods for damping inter-area oscillations with low frequencies, so the damping control can be more effective and easier to design with less interference among different oscillation modes in the power system. A signal-decoupling algorithm was developed that can enable separation of multiple oscillation frequency contents and extraction of a “pure” oscillation frequency mode that are fed into Power System Stabilizers (PSSs) as the modulation input signals. As a result, instead of introducing interferences between different oscillation modes from the traditional approaches, the output of the new PSS modulation control signal mainly affects only one oscillation mode of interest. The new decoupled modulation damping control algorithm has been successfully developed and tested on the standard IEEE 4-machine 2-area test system and a minniWECC system. The results are compared against traditional modulation controls, which demonstrates the validity and effectiveness of the newly-developed decoupled modulation damping control algorithm.

Accounting Training Module Development to Boost Agriculture Financial Literacy on Palm Farmers

Science.gov (United States)

Hasibuan, Henny Triyana; Murwani, Danardana; Widjaja, Sri Umi Mientarti; Witjaksono, Mit

2017-01-01

This research aims to develop agriculture accounting training module in order to increase palm oil farmer financial literacy, in this case farmers in Donomulyo, Malang Regency, Indonesia. The method utilized in model development is Design Based Research using the following progression: problem identification, explanation of goals, design and…

Student-Centered Modules to Support Active Learning in Hydrology: Development Experiences and Users' Perspectives

Science.gov (United States)

Tarboton, D. G.; Habib, E. H.; Deshotel, M.; Merck, M. F.; Lall, U.; Farnham, D. J.

2016-12-01

Traditional approaches to undergraduate hydrology and water resource education are textbook based, adopt unit processes and rely on idealized examples of specific applications, rather than examining the contextual relations in the processes and the dynamics connecting climate and ecosystems. The overarching goal of this project is to address the needed paradigm shift in undergraduate education of engineering hydrology and water resources education to reflect parallel advances in hydrologic research and technology, mainly in the areas of new observational settings, data and modeling resources and web-based technologies. This study presents efforts to develop a set of learning modules that are case-based, data and simulation driven and delivered via a web user interface. The modules are based on real-world case studies from three regional hydrologic settings: Coastal Louisiana, Utah Rocky Mountains and Florida Everglades. These three systems provide unique learning opportunities on topics such as: regional-scale budget analysis, hydrologic effects of human and natural changes, flashflood protection, climate-hydrology teleconnections and water resource management scenarios. The technical design and contents of the modules aim to support students' ability for transforming their learning outcomes and skills to hydrologic systems other than those used by the specific activity. To promote active learning, the modules take students through a set of highly engaging learning activities that are based on analysis of hydrologic data and model simulations. The modules include user support in the form of feedback and self-assessment mechanisms that are integrated within the online modules. Module effectiveness is assessed through an improvement-focused evaluation model using a mixed-method research approach guiding collection and analysis of evaluation data. Both qualitative and quantitative data are collected through student learning data, product analysis, and staff interviews

ATLAS pixel IBL modules construction experience and developments for future upgrade

Energy Technology Data Exchange (ETDEWEB)

Gaudiello, A.

2015-10-01

The first upgrade of the ATLAS Pixel Detector is the Insertable B-Layer (IBL), installed in May 2014 in the core of ATLAS. Two different silicon sensor technologies, planar n-in-n and 3D, are used. Sensors are connected with the new generation 130 nm IBM CMOS FE-I4 read-out chip via solder bump-bonds. Production quality control tests were set up to verify and rate the performance of the modules before integration into staves. An overview of module design and construction, the quality control results and production yield will be discussed, as well as future developments foreseen for future detector upgrades.

Development of a Compact Wireless Laplacian Electrode Module for Electromyograms and Its Human Interface Applications

Directory of Open Access Journals (Sweden)

Akira Ichikawa

2013-02-01

Full Text Available In this study, we developed a compact wireless Laplacian electrode module for electromyograms (EMGs. One of the advantages of the Laplacian electrode configuration is that EMGs obtained with it are expected to be sensitive to the firing of the muscle directly beneath the measurement site. The performance of the developed electrode module was investigated in two human interface applications: character-input interface and detection of finger movement during finger Braille typing. In the former application, the electrode module was combined with an EMG-mouse click converter circuit. In the latter, four electrode modules were used for detection of finger movements during finger Braille typing. Investigation on the character-input interface indicated that characters could be input stably by contraction of (a the masseter, (b trapezius, (c anterior tibialis and (d flexor carpi ulnaris muscles. This wide applicability is desirable when the interface is applied to persons with physical disabilities because the disability differs one to another. The investigation also demonstrated that the electrode module can work properly without any skin preparation. Finger movement detection experiments showed that each finger movement was more clearly detectable when comparing to EMGs recorded with conventional electrodes, suggesting that the Laplacian electrode module is more suitable for detecting the timing of finger movement during typing. This could be because the Laplacian configuration enables us to record EMGs just beneath the electrode. These results demonstrate the advantages of the Laplacian electrode module.

Development of DKB ETL module in case of data conversion

Science.gov (United States)

Kaida, A. Y.; Golosova, M. V.; Grigorieva, M. A.; Gubin, M. Y.

2018-05-01

Modern scientific experiments involve the producing of huge volumes of data that requires new approaches in data processing and storage. These data themselves, as well as their processing and storage, are accompanied by a valuable amount of additional information, called metadata, distributed over multiple informational systems and repositories, and having a complicated, heterogeneous structure. Gathering these metadata for experiments in the field of high energy nuclear physics (HENP) is a complex issue, requiring the quest for solutions outside the box. One of the tasks is to integrate metadata from different repositories into some kind of a central storage. During the integration process, metadata taken from original source repositories go through several processing steps: metadata aggregation, transformation according to the current data model and loading it to the general storage in a standardized form. The R&D project of ATLAS experiment on LHC, Data Knowledge Base, is aimed to provide fast and easy access to significant information about LHC experiments for the scientific community. The data integration subsystem, being developed for the DKB project, can be represented as a number of particular pipelines, arranging data flow from data sources to the main DKB storage. The data transformation process, represented by a single pipeline, can be considered as a number of successive data transformation steps, where each step is implemented as an individual program module. This article outlines the specifics of program modules, used in the dataflow, and describes one of the modules developed and integrated into the data integration subsystem of DKB.

Development of Nanosatellite Technology with APRS Module for Disaster Mitigation

Science.gov (United States)

Prahyang, S. Y.; Dhiya’Ulhaq, M. Z.; Golim, O. P.; Gunawan, R.; Suhandinata; Jahja, E.; Nelwan, E. R. G.; Ananta, C.; Chow, I. M.; Mali, N. D. F.

2018-05-01

Development of nanosatellite technology has enabled satellites to be developed with multiple capabilities for a specific mission in a short time with a low cost. Satellite communications are proved to be more effective in delivering information due to its large coverage area. Surya Satellite-1 will become the first Indonesian nanosatellite developed by undergraduate students. It is designed with low-cost commercial payloads, including an APRS module for communication and operated on VHF and UHF amateur radio frequencies. The mission of the satellites focused on disaster mitigation through APRS communication network with remote stations located on disaster-prone areas.

Development of severe accident guidance module for the SATS simulator

International Nuclear Information System (INIS)

Kim, K.R.; Park, S.H.; Kim, D.H.; Song, Y.M.

2004-01-01

Recently KAERI has developed the severe accident management guidance to establish Korea standard severe accident management system. On the other hand the PC-based severe accident training simulator SATS has been developed, which uses MELCOR code as the simulation engine. SATS graphically displays and simulates the severe accidents with interactive user commands. The control capability of SATS could make severe accident training course more interesting and effective. In this paper we will describe the development and functions of the electrical hypertext guidance module HyperKAMG and the SATS-HyperKAMG linkage system for the severe accident management. (author)

Low cost solar array project production process and equipment task. A Module Experimental Process System Development Unit (MEPSDU)

Science.gov (United States)

1981-01-01

Technical readiness for the production of photovoltaic modules using single crystal silicon dendritic web sheet material is demonstrated by: (1) selection, design and implementation of solar cell and photovoltaic module process sequence in a Module Experimental Process System Development Unit; (2) demonstration runs; (3) passing of acceptance and qualification tests; and (4) achievement of a cost effective module.

NASA/First Materials Science Research Rack (MSRR-1) Module Inserts Development for the International Space Station

Science.gov (United States)

Crouch, Myscha; Carswell, Bill; Farmer, Jeff; Rose, Fred; Tidwell, Paul

1999-01-01

The Material Science Research Rack 1 (MSRR-1) of the Material Science Research Facility (MSRF) contains an Experiment Module (EM) being developed collaboratively by NASA and the European Space Agency (ESA). This NASA/ESA EM will accommodate several different removable and replaceable Module Inserts (MIs) which are installed on orbit. Two of the NASA MIs being developed for specific material science investigations are described herein.

Develop railway engineering modules in UTK civil engineering undergraduate and graduate courses.

Science.gov (United States)

2015-05-31

The importance of railway transport has long been recognized. However, no railway : engineering courses have been provided in the UTK civil engineering curricula. The : objective of this education project is to develop some railway engineering module...

Development of Hydrogen Separation Module with Structured Catalyst for Use in Membrane Reformer

International Nuclear Information System (INIS)

Isamu Yasuda; Tatsuya Tsuneki; Yoshinori Shirasaki; Toru Shimamori; Hidekazu Shigaki; Hiroyuki Tanaka

2006-01-01

A new type of hydrogen separation module for use in a membrane reformer was proposed and developed. The new module, what we call MOC (Membrane On Catalyst), was designed to have a membrane of palladium-based alloy prepared on the surface of the tubular structured catalyst that has catalytic activity for steam reforming reaction, thermal expansion matching with the membrane material, proper porosity, mechanical strength and thermal conductivity. The best composition of the structured catalyst was identified in the composites of metallic Ni and YSZ (Yttria-Stabilized Zirconia). A hydrogen separation module was manufactured by electroless plating of Pd with thickness of 7 to 15 microns on the surface of porous sintered tube of Ni-YSZ with an approximate size of 9 mm in diameter and 100 mm in length. The hydrogen permeability measurements have shown hydrogen flux of 25 to 35 cc/min at 550 to 600 C, which is higher than the permeability of the conventional modules using rolled Pd film. (authors)

Development of Ultrasonic Modulation Probe for Fluorescence Tomography Based on Acousto-Optic Effect

Directory of Open Access Journals (Sweden)

Trinh Quang Duc

2011-01-01

Full Text Available We have developed an ultrasonic probe for fluorescence modulation to image fluorescence within biological tissues. The probe consists of a focused ultrasonic transducer mounted on actuators for mechanical fan scanning, which can be used in contact with the measuring object aiming for clinical application. The mechanical fan scanning employed in the probe has a beneficial feature of portability. As a result, fluorescent beads, which were localized with the diameter of 2 mm at 20 mm depth in a pork meat tissue, were detected with resolution of 3 mm. The system performance denotes the feasibility of development towards the final goal of ultrasonic fluorescence modulation tomography for clinical applications.

Development of Automated Production Line Processes for Solar Brightfield Modules: Final Annual Technical Progress Report, 1 July 2004 -- 15 October 2005

Energy Technology Data Exchange (ETDEWEB)

Nowlan, M. J.; Murach, J. M.; Sutherland, S. F.; Miller, D. C.; Moore S. B.; Hogan, S. J.

2006-08-01

Spire Corporation is addressing the Photovoltaic Manufacturing R&D project goals of improving photovoltaic (PV) manufacturing processes and products while reducing costs and providing a technology foundation that supports significant manufacturing scale-up. To accomplish this, we are focusing our efforts on the design of a large-area utility-scale module and the development of the necessary manufacturing techniques and equipment to manufacture such a module in a high-volume production environment. A three-phase program is under way for developing and demonstrating new automated systems for fabricating very large PV modules ideal for use in multi-megawatt grid-connected applications. We designed a large-area (1.57 m x 3.68 m) 800-W module, and we are developing associated module production equipment that will minimize the total installed system cost for utility-scale PV arrays. Activities in Phase 2 focused on the development of automation for module materials lay-up, cell string busing, and module lamination; enhancements to the cell stringing and lamination processes; and performance testing of large-area modules.

Development of RFS. NUCIRC Interaction Module

International Nuclear Information System (INIS)

Choi, Geun Suk; Park, Joo Hwan

2010-01-01

For heavy water reactor core analysis and thermal hydraulic analysis, RFSP code and the NUCIRC code should be used consecutively. In this case the result of computation of one program is used for input data and information of the other program. For example, it is determining the channel flow distribution of 100% power from the NUCIRC code by using time-averaged bundle power distribution data of 100% power calculated from the RFSP code. However, a result of coming out of the RFSP code don't give converged input data about bundle power. Because of that, it calculates many times and it has to deliver with NUCIRC input. The troublesome process calculated by the PYTHON program. PYTHON is the script language. The connected python module of the RFSP code and NUCIRC code were developed in order to overcome this disadvantage. The Modeling is CANDU 6 reactor

Enhanced thermaly managed packaging for III-nitride light emitters

Science.gov (United States)

Kudsieh, Nicolas

In this Dissertation our work on `enhanced thermally managed packaging of high power semiconductor light sources for solid state lighting (SSL)' is presented. The motivation of this research and development is to design thermally high stable cost-efficient packaging of single and multi-chip arrays of III-nitrides wide bandgap semiconductor light sources through mathematical modeling and simulations. Major issues linked with this technology are device overheating which causes serious degradation in their illumination intensity and decrease in the lifetime. In the introduction the basics of III-nitrides WBG semiconductor light emitters are presented along with necessary thermal management of high power cingulated and multi-chip LEDs and laser diodes. This work starts at chip level followed by its extension to fully packaged lighting modules and devices. Different III-nitride structures of multi-quantum well InGaN/GaN and AlGaN/GaN based LEDs and LDs were analyzed using advanced modeling and simulation for different packaging designs and high thermal conductivity materials. Study started with basic surface mounted devices using conventional packaging strategies and was concluded with the latest thermal management of chip-on-plate (COP) method. Newly discovered high thermal conductivity materials have also been incorporated for this work. Our study also presents the new approach of 2D heat spreaders using such materials for SSL and micro LED array packaging. Most of the work has been presented in international conferences proceedings and peer review journals. Some of the latest work has also been submitted to well reputed international journals which are currently been reviewed for publication. .

Development and Evaluation of an Undergraduate Science Communication Module

Science.gov (United States)

Yeoman, Kay H.; James, Helen A.; Bowater, Laura

2011-01-01

This paper describes the design and evaluation of an undergraduate final year science communication module for the Science Faculty at the University of East Anglia. The module focuses specifically on science communication and aims to bring an understanding of how science is disseminated to the public. Students on the module are made aware of the…

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of thin-film polycrystalline solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to realize the practical application of the above-named solar module expected to exhibit higher efficiency and reliability and achieve cost reduction through consumption of less materials. In fiscal 1998, 1) technologies were developed to reduce substrate warpage during recrystallization for the higher-throughput fabrication of high-quality thin films and 2) technologies were also developed for the realization of higher-throughput fabrication of thin films and for efficiency improvement for thin-film modules. Under item 1), experiments were conducted by simulation for reducing warpage to occur in thin-film polycrystalline Si substrates during fabrication by melting and recrystallization. Under item 2), for the development of thin-film cell high-throughput technologies, studies were started on a more practical hydrogen plasma process to challenge the conventional process of crystal defect inactivation by hydrogen ion injection with which achievement of high throughputs is difficult. For the development of technologies for the enhancement of thin-film module efficiency, efforts were exerted to realize a 10cm times 10cm square shape for the enhancement of efficiency in the process of filling modules with cells. These efforts achieved a great step toward future practical application. (NEDO)

"Scaffolding" of Action Learning within a Part-Time Management Development Module

Science.gov (United States)

Joesbury, Mark

2015-01-01

This Account of Practice describes the introduction and development of action learning within a level 5 module of "Communications at Work" delivered as part of a Business & Technology Education Council (BTEC) Professional Certificate in Management (CMS) between 2005/2006 and 2009/2010. This will commence with a personal narrative and…

Developing an Implementation Plan. The Administration of Career Education: Module 8.

Science.gov (United States)

Drier, Harry N., Jr., Ed.; Martinez, Nancy S., Ed.

The module is one of a series of eight developed to provide inservice education training for administrators of career education programs. An examination of basic scientific planning approaches and procedures is presented to provide the administrator with a basic tool to implement career education. Various scientific management techniques and their…

Development of Automated Production Line Processes for Solar Brightfield Modules: Annual Technical Progress Report, 1 January 2003 -- 30 June 2004

Energy Technology Data Exchange (ETDEWEB)

Nowlan, M. J.; Murach, J. M.; Sutherland, S. F.; Miller, D. C.; Moore, S. B.; Hogan, S. J.

2005-06-01

This report describes how Spire Corporation is addressing the PV Manufacturing R&D project goals of improving photovoltaic (PV) manufacturing processes and products while reducing costs and providing a technology foundation that supports significant manufacturing scale-up. To accomplish this, we are focusing our efforts on the design of a large-area utility-scale module and the development of the necessary manufacturing techniques and equipment to manufacture such a module in a high-volume production environment. A three-phase program is under way for developing and demonstrating new automated systems for fabricating very large PV modules ideal for use in multi-megawatt grid-connected applications. We designed a large-area 800 W module and we are developing associated module production equipment that will minimize the total installed system cost for utility-scale PV arrays. Unique features of the module design include a cantilevered glass superstrate to reduce the glass thickness a nd internally laminated bypass diodes that simplify internal busing and junction-box designs. Other program activities include the development of automation for solar cell string inspections, string busing, materials lay-up, and lamination; enhancements to the lamination process; and performance testing of large-area modules.

Design and development of neutral beam module components

International Nuclear Information System (INIS)

Holl, P.M.; Bulmer, R.H.; Dilgard, L.W.; Horvath, J.A.; Molvik, A.W.; Porter, G.D.; Shearer, J.W.; Slack, D.S.; Colonias, J.S.

1979-01-01

The Mirror Fusion Test Facility (MFTF) injection system consists of twenty 20 keV start-up, and twenty-four 80 keV sustaining neutral beam source modules. The neutral beam modules are mounted in four clusters equally spaced around the waist of the vacuum vessel which contains the superconducting magnets. A module is defined here as an assembly consisting of a beam source and the interfacing components between that beam source and the vacuum chamber. Six major interfacing components are the subject of this paper. They are the magnetic shield, the neutralizer duct, the isolation valve, mounting gimbals, aiming bellows and actuators

Towards developing high-fidelity simulated learning environment training modules in audiology.

Science.gov (United States)

Dzulkarnain, A A; Rahmat, S; Mohd Puzi, N A F; Badzis, M

2017-02-01

This discussion paper reviews and synthesises the literature on simulated learning environment (SLE) from allied health sciences, medical and nursing in general and audiology specifically. The focus of the paper is on discussing the use of high-fidelity (HF) SLE and describing the challenges for developing a HF SLE for clinical audiology training. Through the review of the literature, this paper discusses seven questions, (i) What is SLE? (ii) What are the types of SLEs? (iii) How is SLE classified? (iv) What is HF SLE? (v) What types of SLEs are available in audiology and their level of fidelity? (vi) What are the components needed for developing HF SLE? (vii) What are the possible types of HF SLEs that are suitable for audiology training? Publications were identified by structured searches from three major databases PubMed, Web of Knowledge and PsychInfo and from the reference lists of relevant articles. The authors discussed and mapped the levels of fidelity of SLE audiology training modules from the literature and the learning domains involved in the clinical audiology courses. The discussion paper has highlighted that most of the existing SLE audiology training modules consist of either low- or medium-fidelity types of simulators. Those components needed to achieve a HF SLE for audiology training are also highlighted. Overall, this review recommends that the combined approach of different levels and types of SLE could be used to obtain a HF SLE training module in audiology training.

Using Instructional Design, Analyze, Design, Develop, Implement, and Evaluate, to Develop e-Learning Modules to Disseminate Supported Employment for Community Behavioral Health Treatment Programs in New York State.

Science.gov (United States)

Patel, Sapana R; Margolies, Paul J; Covell, Nancy H; Lipscomb, Cristine; Dixon, Lisa B

2018-01-01

Implementation science lacks a systematic approach to the development of learning strategies for online training in evidence-based practices (EBPs) that takes the context of real-world practice into account. The field of instructional design offers ecologically valid and systematic processes to develop learning strategies for workforce development and performance support. This report describes the application of an instructional design framework-Analyze, Design, Develop, Implement, and Evaluate (ADDIE) model-in the development and evaluation of e-learning modules as one strategy among a multifaceted approach to the implementation of individual placement and support (IPS), a model of supported employment for community behavioral health treatment programs, in New York State. We applied quantitative and qualitative methods to develop and evaluate three IPS e-learning modules. Throughout the ADDIE process, we conducted formative and summative evaluations and identified determinants of implementation using the Consolidated Framework for Implementation Research (CFIR). Formative evaluations consisted of qualitative feedback received from recipients and providers during early pilot work. The summative evaluation consisted of levels 1 and 2 (reaction to the training, self-reported knowledge, and practice change) quantitative and qualitative data and was guided by the Kirkpatrick model for training evaluation. Formative evaluation with key stakeholders identified a range of learning needs that informed the development of a pilot training program in IPS. Feedback on this pilot training program informed the design document of three e-learning modules on IPS: Introduction to IPS, IPS Job development, and Using the IPS Employment Resource Book . Each module was developed iteratively and provided an assessment of learning needs that informed successive modules. All modules were disseminated and evaluated through a learning management system. Summative evaluation revealed that

Development of intergrated accident management assessment technology; development of interface modules of risk-monitoring system

Energy Technology Data Exchange (ETDEWEB)

Kang, S. K.; Park, S. K.; Seok, H.; Kim, D. K.; Han, J. K.; Park, B. R. [KOPEC, Taejeon (Korea)

2002-03-01

Based on the development of interface modules with FORTE.- DynaRM can quantify risk model very fast (Very frequent risk model quantification is needed for configuration risk management).- risk monitoring system technology transfer to foreign NPPs. Contribution to component failure and maintenance control automation with the development of Tagging control System. On-Line risk monitoring system development by joint team between Korea Atomic Energy Research Institute and KOPEC is a request by KEPCO. The softwares developed in this study is easily implemented at domestic NPPs without extra study or cost. Economic benefit and Software export to foreign NPPs are expected because of the development of technology related to risk monitoring system and its management. 6 refs., 3 figs., 1 tab. (Author)

Module-based Simulation System for efficient development of nuclear simulation programs

International Nuclear Information System (INIS)

Yoshikawa, Hidekazu; Wakabayashi, Jiro

1990-01-01

Module-based Simulation System (MSS) has been developed to realize a new software environment enabling versatile dynamic simulation of a complex nuclear power plant system flexibly. Described in the paper are (i) fundamental methods utilized in MMS and its software systemization, (ii) development of human interface system to help users in generating integrated simulation programs automatically, and (iii) development of an intelligent user support system for helping users in the two phases of automatical semantic diagnosis and consultation to automatic input data setup for the MSS-generated programs. (author)

Status Report on NEAMS System Analysis Module Development

Energy Technology Data Exchange (ETDEWEB)

Hu, R. [Argonne National Lab. (ANL), Argonne, IL (United States); Fanning, T. H. [Argonne National Lab. (ANL), Argonne, IL (United States); Sumner, T. [Argonne National Lab. (ANL), Argonne, IL (United States); Yu, Y. [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-12-01

Under the Reactor Product Line (RPL) of DOE-NE’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, an advanced SFR System Analysis Module (SAM) is being developed at Argonne National Laboratory. The goal of the SAM development is to provide fast-running, improved-fidelity, whole-plant transient analyses capabilities. SAM utilizes an object-oriented application framework MOOSE), and its underlying meshing and finite-element library libMesh, as well as linear and non-linear solvers PETSc, to leverage modern advanced software environments and numerical methods. It also incorporates advances in physical and empirical models and seeks closure models based on information from high-fidelity simulations and experiments. This report provides an update on the SAM development, and summarizes the activities performed in FY15 and the first quarter of FY16. The tasks include: (1) implement the support of 2nd-order finite elements in SAM components for improved accuracy and computational efficiency; (2) improve the conjugate heat transfer modeling and develop pseudo 3-D full-core reactor heat transfer capabilities; (3) perform verification and validation tests as well as demonstration simulations; (4) develop the coupling requirements for SAS4A/SASSYS-1 and SAM integration.

Development and implementation of quality control strategies for CMS silicon strip tracker modules

International Nuclear Information System (INIS)

Dirkes, G.

2003-01-01

The CMS group in Karlsruhe is involved in the construction of the silicon trackers end-caps and will produce and qualify the 1 600 modules of ring 5. Therefore automatic test systems for module qualification are developed and test strategies are worked out. For the electrical tests a complete readout system is developed, based on readout modules available within the collaboration and extended by home build modules. These are based on a modular approach with less complex functional units attached to a motherboard and includes key functionalities like clock and trigger generation and their distribution, high and low voltage supply and test signal generation usable with lasers or infrared LEDs. The motherboard is connected to a standard PC, hosting a fast ADC, interface cards to the motherboard and the front-end electronics. Already during the R and D phase of this readout system, first prototype tests were performed and some weak points of the design were uncovered, resulting in changes of the electronics design of the front end hybrids. Two test stations are built. The first one focuses on a fast functionality test, which includes an active thermal cycle with readout at -10 C performed for each individual module. The other test station focuses on debugging and repair requirements. It disposes of sufficient space for a flexible use of the system, including the possibility of additional test options with lasers, radioactive sources, probes and LEDs. For quality control measurements at module level it turned out, that LEDs are of good use: Besides external signal generation by running them in a pulsed way, they can be used for constant illumination of sensors, inducing an artificial leakage current. This led to the discovery of gain losses of complete readout chips induced by shorted AC coupling capacitances of several readout channels, which are called pinholes. Therefore pinholes must be unbonded from the front end preamplifier, which requires faultless

THE DEVELOPMENT OF SCIENCE LEARNING MODULE FOR CHILDRENT WITH HEARING IMPAIRMENT

Directory of Open Access Journals (Sweden)

Ahmad Marzuqi

2017-02-01

Full Text Available There are the absence of teaching materials in accordance with the characteristics and conditions of a hearing impairment children in terms of learning, especially science subjects. The characteristics of hearing impairment children is poor in their vocabularies, so that, the teaching materials emphasizing the visual aspect is necessary. This study used a Research and Development (R & D adapted by the Sugiyono model in order to produce teaching materials in the form of pictorial modules and to test their effectiveness. The result of the research showed that it was a very valid criteria with a score of 97% of the materials experts, 85% of media experts, and 93% of skilled practitioners. The score of the effectiveness of the modules was 75% with the effective criteria.

Development of Instructional Materials for Electrochemical Module Class XII Science High School Students with Guided Inquiry Learning Approach

Directory of Open Access Journals (Sweden)

Lilik Fatmawati

2014-06-01

Full Text Available Pengembangan Bahan Ajar Modul Elektrokimia untuk Siswa SMA Kelas XII IPA dengan Pendekatan Pembelajaran Inkuiri Terbimbing Abstract: The aim of this study was to determine the feasibility and effectiveness of the electrochemical module for high school students of class XII results of development. Electrochemical module of the development consists of two learning activities, ie to the material Volta cells and electrolysis cells for the material. Results of the assessment by two chemistry lecturer, State University of Malang and two chemistry teachers XII as an expert content / learning material for eligibility contents was 92.9%, for eligibility and completeness of presentation is 91.1%, and for the eligibility of language is 92.3% , which is classified as very feasible criteria. Overall the average value was 92.1 feasibility. Effectiveness module is indicated by the results of the development of perception and student learning outcomes. Students' perceptions obtained from student assessment results to module development. In the limited field trials obtained average value is 81.8 for all aspects of the maximum value of 100. Obtaining the average value of student learning outcomes for the cognitive aspect is 83.3, for the affective aspect is 82.3, and for the psychomotor aspect is 83.8 out of 100. The maximum value of the overall results of the study showed that the electrochemical module for high school students Class XII Science development results are very decent and very effectively used in the learning process. Key Words: guided inquiry, electrochemical module, model 4-D Abstrak: Tujuan penelitian ini adalah mengetahui kelayakan, dan keefektifan modul elektrokimia untuk siswa SMA kelas XII hasil pengembangan. Modul Elektrokimia hasil pengembangan terdiri dari dua kegiatan belajar, yaitu untuk materi sel Volta dan untuk materi sel elektrolisis. Hasil penilaian oleh dua dosen kimia Universitas Negeri Malang dan dua guru kimia kelas XII sebagai

A study on embedded resistor components fabricated by laser micro-cladding and rapid prototype

International Nuclear Information System (INIS)

Li Huiling; Zeng Xiaoyan

2006-01-01

With the rapid development of IC and packaging, electronic devices are required to be smaller, to have a high-density integration, to become multifunction and to be of lower cost and high-reliability. Thick-film technology is not able to meet the current developing demands because of its shortcomings, such as the limit of pattern resolution, the severe torsion and delay of high-speed signal transmission. The speed and quality of signal transmission will be improved if embedded resistor components are directly integrated in the multiplayer substrate of multi-chip or laminated module, and high-density integration and reliability are achieved because the short interconnection and the less soldering point. In this paper, a technique named laser micro-cladding and rapid prototype is used to directly fabricate embedded resistor units on the multiplayer ceramic substrate without using a mask and high-temperature sintering, and without trimming resistor, which will simplify processing and decrease cost as well as improving high-speed and reliable performance

Development of user interface to support automatic program generation of nuclear power plant analysis by module-based simulation system

International Nuclear Information System (INIS)

Yoshikawa, Hidekazu; Mizutani, Naoki; Nakaya, Ken-ichiro; Wakabayashi, Jiro

1988-01-01

Module-based Simulation System (MSS) has been developed to realize a new software work environment enabling versatile dynamic simulation of a complex nuclear power system flexibly. The MSS makes full use of modern software technology to replace a large fraction of human software works in complex, large-scale program development by computer automation. Fundamental methods utilized in MSS and developmental study on human interface system SESS-1 to help users in generating integrated simulation programs automatically are summarized as follows: (1) To enhance usability and 'communality' of program resources, the basic mathematical models of common usage in nuclear power plant analysis are programed as 'modules' and stored in a module library. The information on usage of individual modules are stored in module database with easy registration, update and retrieval by the interactive management system. (2) Target simulation programs and the input/output files are automatically generated with simple block-wise languages by a precompiler system for module integration purpose. (3) Working time for program development and analysis in an example study of an LMFBR plant thermal-hydraulic transient analysis was demonstrated to be remarkably shortened, with the introduction of an interface system SESS-1 developed as an automatic program generation environment. (author)

Documentation of the Oil and Gas Supply Module (OGSM). Appendix, Model developers report

International Nuclear Information System (INIS)

1995-01-01

The Office of Integrated Analysis and Forecasting (OIAF) is required to provide complete model documentation to meet the EIA Model Acceptance Standards. The Documentation for the Oil and Gas Supply Module (OGSM) provides a complete description of the OGSM methodology, structure, and relation to other modules in the National Energy Modeling System (NEMS). This Model Developers Report (MDR) serves as an appendix to the methodology documentation. This report provides an overview of the model and an assessment of the sensitivity of OGSM results to changes in input data or parameters

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development of novel type solar cell module integratable with building materials - Novel multilayer structure module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu - shinfukuso kozo module)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The project aims to develop solar cell modules of a novel multilayer structure, based on the resin filling structure, hollow structure, and the laminate structure, and integratable with building materials. In fiscal 1999, for the development of cells and submodule structures, cells and submodules were fabricated which were usable with various specimens. In the case of design oriented cells, electrode structures and linkage methods were improved for the enhancement of power generation performance, and a hollow structure and a laminate structure were fabricated. As for the 4m{sup 2}-large module (laminate structure), a specimen with dummy cells arranged along its periphery was fabricated. For cost reduction, a study was made about a module (laminate structure) integrated with an ALC (autoclaved lightweight concrete) board, and the kind of surface glass, cell arrangement, and back sheet types and their respective designs were evaluated. It was then concluded that the module was fit for practical application. The module was then checked for wind endurance in a wind endurance test, for electric characteristics, and for flame inhibition capability in a fire prevention/resistance test. (NEDO)

Inspiring Climate Education Excellence(ICEE): Developing Elearning professional development modules - secondary science teachers

Science.gov (United States)

Kellagher, E.; Buhr, S. M.; Lynds, S. E.; McCaffrey, M. S.; Cires Education Outreach

2011-12-01

Inspiring Climate Education Excellence (ICEE) is a NASA-funded project to develop content knowledge and knowledge of effective teaching strategies in climate education among secondary science teachers. ICEE resources are aligned with the Essential Principles of Climate Science. Building upon a needs assessment and face to face workshop, ICEE resources include iTunesU videos, an ICEE 101 resource site with videos and peer-reviewed learning activities, and a moderated online forum. Self-directed modules and an online course are being developed around concepts and topics in which teachers express the most interest and need for instruction. ICEE resources include attention to effective teaching strategies, such as awareness of student misconceptions, strategies for forestalling controversy and advice from master teachers on implementation and curriculum development. The resources are being developed in partnership with GLOBE, and the National Science Digital Library (NSDL) and are informed by the work of the Climate Literacy and Energy Awareness Network (CLEAN) project. ICEE will help to meet the professional development needs of teachers, including those participating in the GLOBE Student Climate Research Campaign.

Development and Applicability Demonstration of a Remote Inspection Module for Inspection of Reactor Internals in an SFR

International Nuclear Information System (INIS)

Kim, Hoewoong; Joo, Youngsang; Park, Changgyu; Kim, Jongbum; Bae, Jinho

2014-01-01

Since liquid sodium is optically opaque, the ultrasonic inspection technique has been mainly employed for inspection of reactor internals in a Sodium-cooled Fast Reactor (SFR). Until now, two types of ultrasonic sensors have been mainly developed; immersion and waveguide sensors. An immersion sensor can provide a high-resolution image, but it may have problems in terms of reliability and life time because the sensor is exposed to high temperature during inspection. On the other hand, a waveguide sensor can maintain its performance during long-term inspection in high temperature because it installs an ultrasonic transducer in a cold region even though such a high-frequency ultrasonic wave cannot be used owing to the long propagation distance [4-6]. In this work, a remote inspection module employing four 10 m long waveguide sensors was newly developed and several performance tests were carried out in water to demonstrate the applicability of the developed remote inspection module to inspection of reactor internals in an SFR. In this work, a remote inspection module for inspection of reactor internals in an SFR was newly developed. The developed remote inspection module employs four 10 m long waveguide sensors for multiple inspection applications: a horizontal beam waveguide sensor for ranging inspection, two vertical beam waveguide sensors for viewing inspection and a 45 .deg. angle beam waveguide sensor for identification inspection. Several performance tests such as ranging, viewing and identification inspections were carried out for simulated nuclear fuel assembly specimens in water, and the applicability of the developed remote inspection module to inspection of reactor internals in an SFR was demonstrated

Development and Applicability Demonstration of a Remote Inspection Module for Inspection of Reactor Internals in an SFR

Energy Technology Data Exchange (ETDEWEB)

Kim, Hoewoong; Joo, Youngsang; Park, Changgyu; Kim, Jongbum [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Bae, Jinho [National Fusion Research Institute, Daejeon (Korea, Republic of)

2014-05-15

Since liquid sodium is optically opaque, the ultrasonic inspection technique has been mainly employed for inspection of reactor internals in a Sodium-cooled Fast Reactor (SFR). Until now, two types of ultrasonic sensors have been mainly developed; immersion and waveguide sensors. An immersion sensor can provide a high-resolution image, but it may have problems in terms of reliability and life time because the sensor is exposed to high temperature during inspection. On the other hand, a waveguide sensor can maintain its performance during long-term inspection in high temperature because it installs an ultrasonic transducer in a cold region even though such a high-frequency ultrasonic wave cannot be used owing to the long propagation distance [4-6]. In this work, a remote inspection module employing four 10 m long waveguide sensors was newly developed and several performance tests were carried out in water to demonstrate the applicability of the developed remote inspection module to inspection of reactor internals in an SFR. In this work, a remote inspection module for inspection of reactor internals in an SFR was newly developed. The developed remote inspection module employs four 10 m long waveguide sensors for multiple inspection applications: a horizontal beam waveguide sensor for ranging inspection, two vertical beam waveguide sensors for viewing inspection and a 45 .deg. angle beam waveguide sensor for identification inspection. Several performance tests such as ranging, viewing and identification inspections were carried out for simulated nuclear fuel assembly specimens in water, and the applicability of the developed remote inspection module to inspection of reactor internals in an SFR was demonstrated.

The development of a valid discovery-based learning module to improve students' mathematical connection

Science.gov (United States)

Kuneni, Erna; Mardiyana, Pramudya, Ikrar

2017-08-01

Geometry is the most important branch in mathematics. The purpose of teaching this material is to develop students' level of thinking for a better understanding. Otherwise, geometry in particular, has contributed students' failure in mathematics examinations. This problem occurs due to special feature in geometry which has complexity of correlation among its concept. This relates to mathematical connection. It is still difficult for students to improve this ability. This is because teachers' lack in facilitating students towards it. Eventhough, facilitating students can be in the form of teaching material. A learning module can be a solution because it consists of series activities that should be taken by students to achieve a certain goal. A series activities in this case is adopted by the phases of discovery-based learning model. Through this module, students are facilitated to discover concept by deep instruction and guidance. It can build the mathematical habits of mind and also strengthen the mathematical connection. Method used in this research was ten stages of research and development proposed by Bord and Gall. The research purpose is to create a valid learning module to improve students' mathematical connection in teaching quadrilateral. The retrieved valid module based on media expert judgment is 2,43 for eligibility chart aspect, 2,60 for eligibility presentation aspect, and 3,00 for eligibility contents aspect. Then the retrieved valid module based on material expert judgment is 3,10 for eligibility content aspect, 2,87 for eligibility presentation aspect, and 2,80 for eligibility language and legibility aspect.

Development of a CMOS time memory cell VLSI and CAMAC module with 0.5 ns resolution

International Nuclear Information System (INIS)

Arai, Y.; Ikeno, M.; Matsumura, T.

1992-01-01

A CMOS time-to-digital converter chip, the Time Memory Cell (TMC), for high-rate wire chamber application has been developed. The chip has a timing resolution of 0.52 ns, dissipates only 7 mW/channel, and contains 4 channels in a chip. Each channel has 1024 memory locations which act as a buffer 1μs deep. The chip was fabricated in a 0.8 μm CMOS process and is 5.0 mm by 5.6 mm. Using the TMC chip, a CAMAC module with 32 input channels was developed. This module is designed to operate in both 'Common Start' and 'Common Stop' modes. The circuit of the module and test results are described in this paper

VLSI 'smart' I/O module development

Science.gov (United States)

Kirk, Dan

The developmental history, design, and operation of the MIL-STD-1553A/B discrete and serial module (DSM) for the U.S. Navy AN/AYK-14(V) avionics computer are described and illustrated with diagrams. The ongoing preplanned product improvement for the AN/AYK-14(V) includes five dual-redundant MIL-STD-1553 channels based on DSMs. The DSM is a front-end processor for transferring data to and from a common memory, sharing memory with a host processor to provide improved 'smart' input/output performance. Each DSM comprises three hardware sections: three VLSI-6000 semicustomized CMOS arrays, memory units to support the arrays, and buffers and resynchronization circuits. The DSM hardware module design, VLSI-6000 design tools, controlware and test software, and checkout procedures (using a hardware simulator) are characterized in detail.

Using Instructional Design, Analyze, Design, Develop, Implement, and Evaluate, to Develop e-Learning Modules to Disseminate Supported Employment for Community Behavioral Health Treatment Programs in New York State

Directory of Open Access Journals (Sweden)

Sapana R. Patel

2018-05-01

Full Text Available BackgroundImplementation science lacks a systematic approach to the development of learning strategies for online training in evidence-based practices (EBPs that takes the context of real-world practice into account. The field of instructional design offers ecologically valid and systematic processes to develop learning strategies for workforce development and performance support.ObjectiveThis report describes the application of an instructional design framework—Analyze, Design, Develop, Implement, and Evaluate (ADDIE model—in the development and evaluation of e-learning modules as one strategy among a multifaceted approach to the implementation of individual placement and support (IPS, a model of supported employment for community behavioral health treatment programs, in New York State.MethodsWe applied quantitative and qualitative methods to develop and evaluate three IPS e-learning modules. Throughout the ADDIE process, we conducted formative and summative evaluations and identified determinants of implementation using the Consolidated Framework for Implementation Research (CFIR. Formative evaluations consisted of qualitative feedback received from recipients and providers during early pilot work. The summative evaluation consisted of levels 1 and 2 (reaction to the training, self-reported knowledge, and practice change quantitative and qualitative data and was guided by the Kirkpatrick model for training evaluation.ResultsFormative evaluation with key stakeholders identified a range of learning needs that informed the development of a pilot training program in IPS. Feedback on this pilot training program informed the design document of three e-learning modules on IPS: Introduction to IPS, IPS Job development, and Using the IPS Employment Resource Book. Each module was developed iteratively and provided an assessment of learning needs that informed successive modules. All modules were disseminated and evaluated through a learning

Ultra-Wideband Optical Modulation Spectrometer (OMS) Development

Science.gov (United States)

Gardner, Jonathan (Technical Monitor); Tolls, Volker

2004-01-01

The optical modulation spectrometer (OMS) is a novel, highly efficient, low mass backend for heterodyne receiver systems. Current and future heterodyne receiver systems operating at frequencies up to a few THz require broadband spectrometer backends to achieve spectral resolutions of R approximately 10(exp 5) to 10(exp 6) to carry out many important astronomical investigations. Among these are observations of broad emission and absorption lines from extra-galactic objects at high redshifts, spectral line surveys, and observations of planetary atmospheres. Many of these lines are pressure or velocity broadened with either large half-widths or line wings extending over several GHz. Current backend systems can cover the needed bandwidth only by combining the output of several spectrometers, each with typically up to 1 GHz bandwidth, or by combining several frequency-shifted spectra taken with a single spectrometer. An ultra-wideband optical modulation spectrometer with 10 - 40 GHz bandwidth will enable broadband ob- servations without the limitations and disadvantages of hybrid spectrometers. Spectrometers like the OMS will be important for both ground-based observatories and future space missions like the Single Aperture Far-Infrared Telescope (SAFIR) which might carry IR/submm array heterodyne receiver systems requiring a spectrometer for each array pixel. Small size, low mass and small power consumption are extremely important for space missions. This report summarizes the specifications developed for the OMS and lists already identified commercial parts. The report starts with a review of the principle of operation, then describes the most important components and their specifications which were derived from theory, and finishes with a conclusion and outlook.

Assessment of microelectronics packaging for high temperature, high reliability applications

Energy Technology Data Exchange (ETDEWEB)

Uribe, F.

1997-04-01

This report details characterization and development activities in electronic packaging for high temperature applications. This project was conducted through a Department of Energy sponsored Cooperative Research and Development Agreement between Sandia National Laboratories and General Motors. Even though the target application of this collaborative effort is an automotive electronic throttle control system which would be located in the engine compartment, results of this work are directly applicable to Sandia`s national security mission. The component count associated with the throttle control dictates the use of high density packaging not offered by conventional surface mount. An enabling packaging technology was selected and thermal models defined which characterized the thermal and mechanical response of the throttle control module. These models were used to optimize thick film multichip module design, characterize the thermal signatures of the electronic components inside the module, and to determine the temperature field and resulting thermal stresses under conditions that may be encountered during the operational life of the throttle control module. Because the need to use unpackaged devices limits the level of testing that can be performed either at the wafer level or as individual dice, an approach to assure a high level of reliability of the unpackaged components was formulated. Component assembly and interconnect technologies were also evaluated and characterized for high temperature applications. Electrical, mechanical and chemical characterizations of enabling die and component attach technologies were performed. Additionally, studies were conducted to assess the performance and reliability of gold and aluminum wire bonding to thick film conductor inks. Kinetic models were developed and validated to estimate wire bond reliability.

Development of a 33 kV, 20 A long pulse converter modulator for high average power klystron

International Nuclear Information System (INIS)

Reghu, T.; Mandloi, V.; Shrivastava, Purushottam

2014-01-01

Research, design, and development of high average power, long pulse modulators for the proposed Indian Spallation Neutron Source are underway at Raja Ramanna Centre for Advanced Technology. With this objective, a prototype of long pulse modulator capable of delivering 33 kV, 20 A at 5 Hz repetition rate has been designed and developed. Three Insulated Gate Bipolar Transistors (IGBT) based switching modules driving high frequency, high voltage transformers have been used to generate high voltage output. The IGBT based switching modules are shifted in phase by 120° with respect to each other. The switching frequency is 25 kHz. Pulses of 1.6 ms pulse width, 80 μs rise time, and 70 μs fall time have been achieved at the modulator output. A droop of ±0.6% is achieved using a simple segmented digital droop correction technique. The total fault energy transferred to the load during fault has been measured by conducting wire burn tests and is found to be within 3.5 J

Development of a 33 kV, 20 A long pulse converter modulator for high average power klystron

Science.gov (United States)

Reghu, T.; Mandloi, V.; Shrivastava, Purushottam

2014-05-01

Research, design, and development of high average power, long pulse modulators for the proposed Indian Spallation Neutron Source are underway at Raja Ramanna Centre for Advanced Technology. With this objective, a prototype of long pulse modulator capable of delivering 33 kV, 20 A at 5 Hz repetition rate has been designed and developed. Three Insulated Gate Bipolar Transistors (IGBT) based switching modules driving high frequency, high voltage transformers have been used to generate high voltage output. The IGBT based switching modules are shifted in phase by 120° with respect to each other. The switching frequency is 25 kHz. Pulses of 1.6 ms pulse width, 80 μs rise time, and 70 μs fall time have been achieved at the modulator output. A droop of ±0.6% is achieved using a simple segmented digital droop correction technique. The total fault energy transferred to the load during fault has been measured by conducting wire burn tests and is found to be within 3.5 J.

Development of a 33 kV, 20 A long pulse converter modulator for high average power klystron

Energy Technology Data Exchange (ETDEWEB)

Reghu, T.; Mandloi, V.; Shrivastava, Purushottam [Pulsed High Power Microwave Section, Raja Ramanna Centre for Advanced Technology, Indore 452013, M.P. (India)

2014-05-15

Research, design, and development of high average power, long pulse modulators for the proposed Indian Spallation Neutron Source are underway at Raja Ramanna Centre for Advanced Technology. With this objective, a prototype of long pulse modulator capable of delivering 33 kV, 20 A at 5 Hz repetition rate has been designed and developed. Three Insulated Gate Bipolar Transistors (IGBT) based switching modules driving high frequency, high voltage transformers have been used to generate high voltage output. The IGBT based switching modules are shifted in phase by 120° with respect to each other. The switching frequency is 25 kHz. Pulses of 1.6 ms pulse width, 80 μs rise time, and 70 μs fall time have been achieved at the modulator output. A droop of ±0.6% is achieved using a simple segmented digital droop correction technique. The total fault energy transferred to the load during fault has been measured by conducting wire burn tests and is found to be within 3.5 J.

Development of Web-Based Common Cause Failure (CCF) Database Module for Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Lee, Hyun-Gyo; Hwang, Seok-Won; Shin, Tae-young [Korea Hydro and Nuclear Power Co. Ltd., Daejeon (Korea, Republic of)

2015-05-15

Probabilistic safety assessment (PSA) has been used to identify risk vulnerabilities and derive the safety improvement measures from construction to operation stages of nuclear power plants. In addition, risk insights from PSA can be applied to improve the designs and operation requirements of plants. However, reliability analysis methods for quantitative PSA evaluation have essentially inherent uncertainties, and it may create a distorted risk profiles because of the differences among the PSA models, plant designs, and operation status. Therefore, it is important to ensure the quality of the PSA model so that analysts identify design vulnerabilities and utilize risk information. Especially, the common cause failure (CCF) has been pointed out as one of major issues to be able to cause the uncertainty related to the PSA analysis methods and data because CCF has a large influence on the PSA results. Organization for economic cooperation and development /nuclear energy agent (OECD/NEA) has implemented an international common cause failure data exchange (ICDE) project for the CCF quality assurance through the development of the detailed analysis methodologies and data sharing. However, Korea Hydro and Nuclear Power company (KHNP) does not have the basis for the data gathering and analysis for CCF analyses. In case of methodology, the Alpha Factor parameter estimation, which can analyze uncertainties and estimate an interface factor (Impact Vector) with an ease, is ready to be applied rather than the Multi Greek Letter (MGL) method. This article summarizes the development of the plant-specific CCF database (DB) module considering the raw data collection and the analysis procedure based on the CCF parameter calculation method of ICDE. Although the portion affected by CCF in the PSA model is quite a large, the development efforts of the tools to collect and analyze data were insufficient. Currently, KHNP intends to improve PSA quality and ensure CCF data reliability by

Development of Web-Based Common Cause Failure (CCF) Database Module for Nuclear Power Plants

International Nuclear Information System (INIS)

Lee, Hyun-Gyo; Hwang, Seok-Won; Shin, Tae-young

2015-01-01

Probabilistic safety assessment (PSA) has been used to identify risk vulnerabilities and derive the safety improvement measures from construction to operation stages of nuclear power plants. In addition, risk insights from PSA can be applied to improve the designs and operation requirements of plants. However, reliability analysis methods for quantitative PSA evaluation have essentially inherent uncertainties, and it may create a distorted risk profiles because of the differences among the PSA models, plant designs, and operation status. Therefore, it is important to ensure the quality of the PSA model so that analysts identify design vulnerabilities and utilize risk information. Especially, the common cause failure (CCF) has been pointed out as one of major issues to be able to cause the uncertainty related to the PSA analysis methods and data because CCF has a large influence on the PSA results. Organization for economic cooperation and development /nuclear energy agent (OECD/NEA) has implemented an international common cause failure data exchange (ICDE) project for the CCF quality assurance through the development of the detailed analysis methodologies and data sharing. However, Korea Hydro and Nuclear Power company (KHNP) does not have the basis for the data gathering and analysis for CCF analyses. In case of methodology, the Alpha Factor parameter estimation, which can analyze uncertainties and estimate an interface factor (Impact Vector) with an ease, is ready to be applied rather than the Multi Greek Letter (MGL) method. This article summarizes the development of the plant-specific CCF database (DB) module considering the raw data collection and the analysis procedure based on the CCF parameter calculation method of ICDE. Although the portion affected by CCF in the PSA model is quite a large, the development efforts of the tools to collect and analyze data were insufficient. Currently, KHNP intends to improve PSA quality and ensure CCF data reliability by

Using scale and feather traits for module construction provides a functional approach to chicken epidermal development.

Science.gov (United States)

Bao, Weier; Greenwold, Matthew J; Sawyer, Roger H

2017-11-01

Gene co-expression network analysis has been a research method widely used in systematically exploring gene function and interaction. Using the Weighted Gene Co-expression Network Analysis (WGCNA) approach to construct a gene co-expression network using data from a customized 44K microarray transcriptome of chicken epidermal embryogenesis, we have identified two distinct modules that are highly correlated with scale or feather development traits. Signaling pathways related to feather development were enriched in the traditional KEGG pathway analysis and functional terms relating specifically to embryonic epidermal development were also enriched in the Gene Ontology analysis. Significant enrichment annotations were discovered from customized enrichment tools such as Modular Single-Set Enrichment Test (MSET) and Medical Subject Headings (MeSH). Hub genes in both trait-correlated modules showed strong specific functional enrichment toward epidermal development. Also, regulatory elements, such as transcription factors and miRNAs, were targeted in the significant enrichment result. This work highlights the advantage of this methodology for functional prediction of genes not previously associated with scale- and feather trait-related modules.

Classes of modules

CERN Document Server

Dauns, John

2006-01-01

Because traditional ring theory places restrictive hypotheses on all submodules of a module, its results apply only to small classes of already well understood examples. Often, modules with infinite Goldie dimension have finite-type dimension, making them amenable to use with type dimension, but not Goldie dimension. By working with natural classes and type submodules (TS), Classes of Modules develops the foundations and tools for the next generation of ring and module theory. It shows how to achieve positive results by placing restrictive hypotheses on a small subset of the complement submodules, Furthermore, it explains the existence of various direct sum decompositions merely as special cases of type direct sum decompositions. Carefully developing the foundations of the subject, the authors begin by providing background on the terminology and introducing the different module classes. The modules classes consist of torsion, torsion-free, s[M], natural, and prenatural. They expand the discussion by exploring...

Development and Implementation of High School Chemistry Modules Using Touch-Screen Technologies

Science.gov (United States)

Lewis, Maurica S.; Zhao, Jinhui; Montclare, Jin Kim

2012-01-01

Technology was employed to motivate and captivate students while enriching their in-class education. An outreach program is described that involved college mentors introducing touch-screen technology into a high school chemistry classroom. Three modules were developed, with two of them specifically tailored to encourage comprehension of molecular…

New development of neutron spectral modulation data analysis

International Nuclear Information System (INIS)

Ito, Y.

1988-01-01

A study is made on procedures for obtaining desired scattering function information. The neutron spectral modulation technique incorporates both the low (including DC) and high frequency Fourier components in its incident spectrum. Lake's procedure increases the Fourier components of the doconvoluted scattering function by using the existing Fourier components as nucleus, thereby bridges the Fourier gap and extends the Fourier region. Since the Lake's procedure takes care of the missing Fourier components, a single measurement using an appropriate NSM modulation suffices to recover the S(W) line shape. Deep modulation depth is not essential to reproduce the scattering function. This should be contrasted to the previous NSM treatment as well as to the neutron spin echo method, both of which require the several repeat of measurements with the varying modulation frequency under the high degree of beam polarization condition. Although the computer simulation of the present paper does not include the statistical fluctuation encountered in the experimental data, these analyses show a great promise of the NSM method, which can now be used with much flexibility in the field of both cold and ultracold neutron scattering experiment. (N.K.)

Pulse position modulation for compact all-fiber vehicle laser rangefinder development

Science.gov (United States)

Mao, Xuesong; Cheng, Yongzhi; Xiong, Ying; Inoue, Daisuke; Kagami, Manabu

2017-10-01

We propose a method for developing small all-fiber vehicle laser rangefinders that is based on pulse position modulation (PPM) and data integration and present a theoretical study on its performance. Compared with spatial coupling, which is employed by most of the current commercial vehicle laser rangefinders, fiber coupling has the advantage that it can guide laser echoes into the interior of a car, so the electronic components following the photodiode can operate in a moderate-temperature environment. However, optical fibers have numerical apertures (NAs), which means that a laser beam from a receiving lens cannot be coupled into an optical fiber if its incident angle exceeds the critical value. Therefore, the effective size of the receiving lens is typically small since it is limited by its focal length and the NA of the fiber, causing the power of the laser echoes gathered by the receiving lens to be insufficient for performing target identification. Instead of increasing the peak transmitting laser power unrestrictedly, PPM and data integration effectively compensate for the low signal-to-noise ratio that results from the effective receiving lens size reduction. We validated the proposed method by conducting numerical simulations and performance analysis. Finally, we compared the proposed method with pseudorandom noise (PN) code modulation and found that, although the two methods perform equally well in single-target measurement scenarios, PPM is more effective than PN code modulation for multitarget measurement. In addition, PPM enables the transmission of laser beams with higher peak powers and requires less computation than PN code modulation does.

Broad Frequency LTCC Vertical Interconnect Transition for Multichip Modules and System on Package Applications

Science.gov (United States)

Decrossas, Emmanuel; Glover, Michael D.; Porter, Kaoru; Cannon, Tom; Mantooth, H. Alan; Hamilton, M. C.

2013-01-01

Various stripline structures and flip chip interconnect designs for high-speed digital communication systems implemented in low temperature co-fired ceramic (LTCC) substrates are studied in this paper. Specifically, two different transition designs from edge launch 2.4 millimeter connectors to stripline transmission lines embedded in LTCC are discussed. After characterizing the DuPont (sup trademark) 9K7 green tape, different designs are proposed to improve signal integrity for high-speed digital data. The full-wave simulations and experimental data validate the presented designs over a broad frequency band from Direct Current to 50 gigahertz and beyond.

Flexible manufacturing for photonics device assembly

Science.gov (United States)

Lu, Shin-Yee; Pocha, Michael D.; Strand, Oliver T.; Young, K. David

1994-01-01

The assembly of photonics devices such as laser diodes, optical modulators, and opto-electronics multi-chip modules (OEMCM), usually requires the placement of micron size devices such as laser diodes, and sub-micron precision attachment between optical fibers and diodes or waveguide modulators (usually referred to as pigtailing). This is a very labor intensive process. Studies done by the opto-electronics (OE) industry have shown that 95 percent of the cost of a pigtailed photonic device is due to the use of manual alignment and bonding techniques, which is the current practice in industry. At Lawrence Livermore National Laboratory, we are working to reduce the cost of packaging OE devices through the use of automation. Our efforts are concentrated on several areas that are directly related to an automated process. This paper will focus on our progress in two of those areas, in particular, an automated fiber pigtailing machine and silicon micro-technology compatible with an automated process.

Medical telesensors

Science.gov (United States)

Ferrell, Trinidad L.; Crilly, P. B.; Smith, S. F.; Wintenberg, Alan L.; Britton, Charles L., Jr.; Morrison, Gilbert W.; Ericson, M. N.; Hedden, D.; Bouldin, Donald W.; Passian, A.; Downey, Todd R.; Wig, A. G.; Meriaudeau, Fabrice

1998-05-01

Medical telesensors are self-contained integrated circuits for measuring and transmitting vital signs over a distance of approximately 1-2 meters. The circuits are unhoused and contain a sensor, signal processing and modulation electronics, a spread-spectrum transmitter, an antenna and a thin-film battery. We report on a body-temperature telesensor, which is sufficiently small to be placed on a tympanic membrane in a child's ear. We also report on a pulse-oximeter telesensor and a micropack receiver/long- range transmitter unit, which receives form a telesensor array and analyzes and re-transmits the vital signs over a longer range. Signal analytics are presented for the pulse oximeter, which is currently in the form of a finger ring. A multichip module is presented as the basic signal-analysis component. The module contains a microprocessor, a field=programmable gate array, memory elements and other components necessary for determining trauma and reporting signals.

Development of high-efficiency solar cells and modules. Optimised production processes and more durable modules can reduce the costs for producing solar power by a third; Hocheffiziente Solarzellen und Module entwickeln. Optimierte Fertigungsablaeufe und langlebigere Module koennen die Erzeugung von Solarstrom um ein Drittel billiger machen

Energy Technology Data Exchange (ETDEWEB)

Hirn, Gerhard

2013-09-01

Research institutes, photovoltaic producers, system manufacturers and solar industry suppliers are working together to produce more powerful and durable modules in a more efficient manner. In the SONNE project, companies and researchers are optimising the output and production of modules made of crystalline silicon cells, whereby they are covering the entire production chain and are making the new developments ready for production in a short time. With their developments they want to reduce the costs of solar power by a third.

The Iterative Development and Use of an Online Problem-Based Learning Module for Preservice and Inservice Teachers

Science.gov (United States)

Rillero, Peter; Camposeco, Laurie

2018-01-01

Teachers' problem-based learning knowledge, abilities, and attitudes are important factors in successful K--12 PBL implementations. This article describes the development and use of a free, online module entitled "Design a Problem-Based Learning Experience." The module production, aligned with theories of andragogy, was a partnership…

The Role of Research in Online Curriculum Development: The Case of "EarthLabs" Climate Change and Earth System Modules

Science.gov (United States)

McNeal, Karen S.; Libarkin, Julie C.; Ledley, Tamara Shapiro; Bardar, Erin; Haddad, Nick; Elins, Kathy; Dutta, Saranee

2014-01-01

This study reports on an effort to illustrate the coupling of educational research with ongoing curriculum development to promote effective and evidence-based online learning. The research findings have been used to inform the "EarthLabs" curriculum development team as they revise existing modules and create new modules, in order to…

Design and development of FPGA based TCP/IP module for real time computers in nuclear power plants

International Nuclear Information System (INIS)

Balasri, G. Janani; Santhana Raj, A.; Gour, Aditya; Murali, N.; Manikandan, J.

2013-01-01

An VME (Virtual Module Europa) bus based Real Time Computer's (RTC's) are being developed for Prototype Fast Breeder Reactor (PFBR) which is in an advanced stage of construction at Kalpakkam, where the RTC's have to communicate to the central process computer on the data collected from the field instrument and receive data from the central process computer. A Distributed Digital Control System (DDSC) architecture has been designed for this communication which is based on Transfer Communication Protocol/Internet Protocol (TCP/IP) over Ethernet. Currently the RTC's uses 'Wiznet Module', a bought out chip which implements the TCP/IP stack in hardware. This project concentrates on the design and development of Field Programmable Gate Array (FPGA) based TCP/IP module that runs on Microblaze, a 32-bit softcore processor, to take care of the communication as that of Wiznet module. Advantage of switching over to FPGA based system are its reconfigurability, desired number of sockets, and the design is stable even if the FPGA's get obsolete. (author)

ATLAS calorimeter and topological trigger upgrades for Phase 1

CERN Document Server

Silverstein, S

2011-01-01

The ATLAS Level-1 Calorimeter Trigger (L1Calo) collaboration is pursuing two hardware upgrade programs for Phase 1 of the LHC upgrade. The first of these is development of a new mixed-signal multi-chip module (MCM) for the PreProcessor system. based on faster FADCs and a modern FPGA. Designed as a drop-in replacement for the existing MCM, the FPGA also enables future upgrades to the PreProcessor algorithms, including enhanced digital filtering and compensation for time-variation of pedestals. It is also planned to augment the current multiplicity-based trigger by adding topology-based algorithms. This is made possible by adding jet and EM/hadron Regions of Interest (ROIs) to the L1Calo real time data path. A synchronous, pipelined topological processor (TP) based on high-density FPGAs and multi-Gbit optical links gathers all ROI information and performs topological algorithms.

arXiv Characterization and Verification Environment for the RD53A Pixel Readout Chip in 65 nm CMOS

CERN Document Server

Vogt, M.; Hemperek, T.; Janssen, J.; Pohl, D.L.; Daas, M.

2018-02-02

The RD53 collaboration is currently designing a large scale prototype pixel readout chip in 65 nm CMOS technology for the phase 2 upgrades at the HL-LHC. The RD53A chip will be available by the end of the year 2017 and will be extensively tested to confirm if the circuit and the architecture make a solid foundation for the final pixel readout chips for the experiments at the HL-LHC. A test and data acquisition system for the RD53A chip is currently under development to perform single-chip and multi-chip module measurements. In addition, the verification of the RD53A design is performed in a dedicated simulation environment. The concept and the implementation of the test and data acquisition system and the simulation environment, which are based on a modular data acquisition and system testing framework, are presented in this work.

Automatically changing modules in modular ontology development and management

CSIR Research Space (South Africa)

Khan, Zubeida C

2017-09-01

Full Text Available Modularity has been proposed as a solution to deal with large ontologies. This requires, various module management tasks, such as swapping an outdated module for a new one or a computationally costly one for a leaner fragment. No mechanism exists...

Assessing upper limb function in nonambulant SMA patients: development of a new module.

Science.gov (United States)

Mazzone, Elena; Bianco, Flaviana; Martinelli, Diego; Glanzman, Allan M; Messina, Sonia; De Sanctis, Roberto; Main, Marion; Eagle, Michelle; Florence, Julaine; Krosschell, Kristin; Vasco, Gessica; Pelliccioni, Marco; Lombardo, Marilena; Pane, Marika; Finkel, Richard; Muntoni, Francesco; Bertini, Enrico; Mercuri, Eugenio

2011-06-01

We report the development of a module specifically designed for assessing upper limb function in nonambulant SMA patients, including young children and those with severe contractures. The application of the module to a preschool cohort of 40 children (age 30-48 months) showed that all the items could be completed by 30 months. The module was also used in 45 nonambulant SMA patients (age 30 months to 27 years). Their scores were more variable than in the preschool cohort, ranging from 0 to 18. The magnitude of scores was not related to age (r=-0.19). The upper limb scores had a good correlation with the Hammersmith Functional Motor Scale, r=0.75, but the upper limb function did not always strictly follow the overall gross motor function. These findings suggest that even some of the very weak nonambulant children possess upper limb skills that can be measured. Copyright © 2011 Elsevier B.V. All rights reserved.

Development and implementation of quality control strategies for CMS silicon strip tracker modules

CERN Document Server

Dirkes, Guido

The LHC will explore physics at the energy frontier and will address many open questions in particle physics, like the search for the Higgs boson or Supersymmetry. For both high resolution track and vertex reconstruction is vital. The CMS silicon tracker consists of 15232 detector modules. Production and assembly of these will span two and a half years period, during which the quality control chain has to ensure functionality and reliability of the modules produced. The CMS group in Karlsruhe will produce and qualify 1600 modules. Therefore automatic test systems are developed and test strategies are worked out. Already during the RnD phase, first prototype tests were performed and some weak points of the design were uncovered. Two test stations are built. One focuses on a fast functionality test, including an active thermal cycle. The other focuses on debugging and repair requirements, including additional test options with lasers, radioactive sources, probes and infrared LEDs. For quality control measuremen...

Developing, Implementing, and Evaluating the Educational Module Students Active Learning via Internet Observations (SALIO) in Undergraduate Nursing Education.

Science.gov (United States)

Salzmann-Erikson, Martin; Bjuhr, Marie; Mårtensson, Gunilla

2017-04-01

This study aimed not only to describe the development and implementation of the module but also to evaluate the nursing students' perceptions. A cross-sectional design including 101 students who were asked to participate and answer a survey. We describe the development of the pedagogic module Students Active Learning via Internet Observations based on situated learning. The findings show that learning about service users' own lived experiences via web-based platforms was instructive according to the students: 81% agreed to a high or very high degree. Another important finding was that 96% of students responded that the module had clinical relevance for nursing work. We argue that learning that engages students with data that are contextually and culturally situated is important for developing competence in caregiving. © 2015 Wiley Periodicals, Inc.

Development of the PedsQL™ Epilepsy Module: Focus group and cognitive interviews.

Science.gov (United States)

Follansbee-Junger, Katherine W; Mann, Krista A; Guilfoyle, Shanna M; Morita, Diego A; Varni, James W; Modi, Avani C

2016-09-01

Youth with epilepsy have impaired health-related quality of life (HRQOL). Existing epilepsy-specific HRQOL measures are limited by not having parallel self- and parent-proxy versions, having a restricted age range, not being inclusive of children with developmental disabilities, or being too lengthy for use in a clinical setting. Generic HRQOL measures do not adequately capture the idiosyncrasies of epilepsy. The purpose of the present study was to develop items and content validity for the PedsQL™ Epilepsy Module. An iterative qualitative process of conducting focus group interviews with families of children with epilepsy, obtaining expert input, and conducting cognitive interviews and debriefing was utilized to develop empirically derived content for the instrument. Eleven health providers with expertise in pediatric epilepsy from across the country provided feedback on the conceptual model and content, including epileptologists, nurse practitioners, social workers, and psychologists. Ten pediatric patients (age 4-16years) with a diagnosis of epilepsy and 11 parents participated in focus groups. Thirteen pediatric patients (age 5-17years) and 17 parents participated in cognitive interviews. Focus groups, expert input, and cognitive debriefing resulted in 6 final domains including restrictions, seizure management, cognitive/executive functioning, social, sleep/fatigue, and mood/behavior. Patient self-report versions ranged from 30 to 33 items and parent proxy-report versions ranged from 26 to 33 items, with the toddler and young child versions having fewer items. Standardized qualitative methodology was employed to develop the items and content for the novel PedsQL™ Epilepsy Module. The PedsQL™ Epilepsy Module has the potential to enhance clinical decision-making in pediatric epilepsy by capturing and monitoring important patient-identified contributors to HRQOL. Copyright © 2016 Elsevier Inc. All rights reserved.

Developing Reading Comprehension Modules to Facilitate Reading Comprehension among Malaysian Secondary School ESL Students

Science.gov (United States)

Javed, Muhammad; Eng, Lin Siew; Mohamed, Abdul Rashid

2015-01-01

The study aims to develop a set of 6 Reading Comprehension Modules (RCMs) for Malaysian ESL teachers to facilitate different reading abilities of ESL students effectively. Different skill categories were selected for developing the RCMs. This article describes how and why diverse texts of varying length were adopted and adapted from various…

Development of intelligent interface for simulation execution by module-based simulation system

International Nuclear Information System (INIS)

Yoshikawa, Hidekazu; Mizutani, Naoki; Shimoda, Hiroshi; Wakabayashi, Jiro

1988-01-01

An intelligent user support for the two phases of simulation execution was newly developed for Module-based Simulation System (MSS). The MSS has been in development as a flexible simulation environment to improve software productivity in complex, large-scale dynamic simulation of nuclear power plant. The AI programing by Smalltalk-80 was applied to materialize the two user-interface programs for (i) semantic diagnosis of the simulation program generated automatically by MSS, and (ii) consultation system by which user can set up consistent numerical input data files necessary for executing a MSS-generated program. Frame theory was utilized in those interface programs to represent the four knowledge bases, which are (i) usage information on module library in MSS and MSS-generated program, and (ii) expertise knowledge on nuclear power plant analysis such as material properties and reactor system configuration. Capabilities of those interface programs were confirmed by some example practice on LMFBR reactor dynamic calculation, and it was demonstrated that the knowledge-based systemization was effective to improve software work environment. (author)

Development of an MR-compatible DOI-PET detector module

Energy Technology Data Exchange (ETDEWEB)

Wei, Qingyang [Department of Electrical Engineering, Tsinghua University, Beijing (China); Key Laboratory of Particle and Radiation Imaging, Ministry of Education (Tsinghua University), Beijing (China); Wang, Shi; Xu, Tianpeng; Gao, Yunpeng; Liu, Yaqiang; Ma, Tianyu [Department of Engineering Physics, Tsinghua University, Beijing (China); Key Laboratory of Particle and Radiation Imaging, Ministry of Education (Tsinghua University), Beijing (China)

2015-05-18

Silicon Photomultiplier (SiPM) is a promising sensor for MR-compatible PET systems. In this paper, we developed a compact 2-layer DOI-PET detector. The top layer is a 15×15 LYSO array, and the crystal size is 2x2x7mm{sup 3}. The bottom layer is a 16×16 array with the same size crystals. There is half-crystal offset between two layers in both transverse directions. The detector is coupled to an 8×8 SiPM array (MicroFB-30035-SMT, Sensl). Sixty-four channels of SiPMs are read out by an ASIC chip with in-chip multiplexing resistor networks in the form of two position and one energy analog signals, and are then converted to wave-form digital signals with 80 MHz 12-bit ADC chips. The energy is calculated by averaging the 3 points around the peak of the pulse. Flood images with two 22Na point sources irradiated on the top and at the bottom of the detector module were acquired. The results show that the detector module achieves good crystal identification capability in both layers with an average energy resolution of 17.1% at 511 keV.

Development of an MR-compatible DOI-PET detector module

International Nuclear Information System (INIS)

Wei, Qingyang; Wang, Shi; Xu, Tianpeng; Gao, Yunpeng; Liu, Yaqiang; Ma, Tianyu

2015-01-01

Silicon Photomultiplier (SiPM) is a promising sensor for MR-compatible PET systems. In this paper, we developed a compact 2-layer DOI-PET detector. The top layer is a 15×15 LYSO array, and the crystal size is 2x2x7mm 3 . The bottom layer is a 16×16 array with the same size crystals. There is half-crystal offset between two layers in both transverse directions. The detector is coupled to an 8×8 SiPM array (MicroFB-30035-SMT, Sensl). Sixty-four channels of SiPMs are read out by an ASIC chip with in-chip multiplexing resistor networks in the form of two position and one energy analog signals, and are then converted to wave-form digital signals with 80 MHz 12-bit ADC chips. The energy is calculated by averaging the 3 points around the peak of the pulse. Flood images with two 22Na point sources irradiated on the top and at the bottom of the detector module were acquired. The results show that the detector module achieves good crystal identification capability in both layers with an average energy resolution of 17.1% at 511 keV.

Engineering study, development and prototype fabrication of the supporting system for the CLIC Two-Beam Module

CERN Document Server

AUTHOR|(CDS)2068725; Karyotakis, Yannis; Dahoo, Pierre Richard; Alexopoulos, Theo; MEIS, Costantin; De Conto, Jean Marie; Jeremie, Andrea; Puzot, Patrique

CERN, the European Organization for Nuclear Research, is based on the international collaboration in the field of high-energy particle physics research. The experiments carried out in its facilities are achieved through the existing particle accelerators. In addition, advanced accelerator research and development is one of the goals of CERN. For this reason, CLIC (the Compact LInear Collider) a new electron-positron linear accelerator is being studied at CERN. CLIC is built by the assembly of the Two-Beam Modules and takes advantage of an innovative acceleration principle, the Two-Beam acceleration. Each Module contains several technical systems that contribute to its successful operation. This thesis presents the development of the prototype supporting system for the CLIC Two-Beam Module. At first, the physics requirements are translated into technical specifications and the fundamental parts of the supporting system are defined. The CLIC operational conditions are identified and the corresponding boundaries...

Space station common module power system network topology and hardware development

Science.gov (United States)

Landis, D. M.

1985-01-01

Candidate power system newtork topologies for the space station common module are defined and developed and the necessary hardware for test and evaluation is provided. Martin Marietta's approach to performing the proposed program is presented. Performance of the tasks described will assure systematic development and evaluation of program results, and will provide the necessary management tools, visibility, and control techniques for performance assessment. The plan is submitted in accordance with the data requirements given and includes a comprehensive task logic flow diagram, time phased manpower requirements, a program milestone schedule, and detailed descriptions of each program task.

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of thin film poly-crystalline solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been performed on a high throughput forming technology and a modularization technology for thin film poly-crystalline solar cell modules. This paper summarizes the achievements in fiscal 1999. In developing the high throughput forming technology for a high-quality thin film, research has been made on a low-cost VEST process to re-utilize substrates by separating the thin film from the substrate. In the melting re-crystallization process, it was discovered that plasticity deformation of the substrate can be reduced greatly by raising the substrate heating temperatures. It was also found out that substrate warping amount can be reduced to about one-fifth of the conventional amount by making the thickness greater than 1.5 mm and raising the heating temperatures higher than 1300 degree C. In developing the thin film modularization technology, it was indicated that the property improving effect remains the same even if the hydrogen passivation method is changed from the hydrogen ion injection to the hydrogen plasma processing. In the trial fabrication of the thin film modules, a conversion efficiency of 13.1% was achieved in nine-cell structured modules. (NEDO)

Development of a NSSS T/H Module for the YGN 1/2 NPP Simulator Using a Best-Estimate Code, RETRAN

International Nuclear Information System (INIS)

Seo, I. Y.; Lee, Y. K.; Jeun, G. D.; Suh, J. S.

2005-01-01

KEPRI(Korea Electric Power Research Institute) developed a realistic nuclear steam supply system thermal-hydraulic module, named ARTS code, based on the best-estimate code RETRAN for the improvement of the KNPEC(Korea Nuclear Plant Education Center) unit 2 full-scope simulator. In this work, we make a nuclear steam supply system thermal-hydraulic module for the YGN 1/2 nuclear power plant simulator using a practical application of a experience of ARTS code development. The ARTS code was developed based on RETRAN, which is a best estimate code developed by EPRI(Electric Power Research Institute) for various transient analyses of NPP(Nuclear Power Plants). Robustness and the real time calculation capability have been improved by simplifications, removing of discontinuities of the physical correlations of the RETRAN code and some other modifications. And its scope for the simulation has been extended by supplementation of new calculation modules such as a dedicated pressurizer relief tank model and a backup model. The supplement is developed so that users cannot recognize the model change from the main ARTS module

Development and pilot testing of an online module for ethics education based on the Nigerian National Code for Health Research Ethics

Science.gov (United States)

2013-01-01

Background The formulation and implementation of national ethical regulations to protect research participants is fundamental to ethical conduct of research. Ethics education and capacity are inadequate in developing African countries. This study was designed to develop a module for online training in research ethics based on the Nigerian National Code of Health Research Ethics and assess its ease of use and reliability among biomedical researchers in Nigeria. Methodology This was a three-phased evaluation study. Phase one involved development of an online training module based on the Nigerian Code of Health Research Ethics (NCHRE) and uploading it to the Collaborative Institutional Training Initiative (CITI) website while the second phase entailed the evaluation of the module for comprehensibility, readability and ease of use by 45 Nigerian biomedical researchers. The third phase involved modification and re-evaluation of the module by 30 Nigerian biomedical researchers and determination of test-retest reliability of the module using Cronbach’s alpha. Results The online module was easily accessible and comprehensible to 95% of study participants. There were significant differences in the pretest and posttest scores of study participants during the evaluation of the online module (p = 0.001) with correlation coefficients of 0.9 and 0.8 for the pretest and posttest scores respectively. The module also demonstrated excellent test-retest reliability and internal consistency as shown by Cronbach’s alpha coefficients of 0.92 and 0.84 for the pretest and posttest respectively. Conclusion The module based on the Nigerian Code was developed, tested and made available online as a valuable tool for training in cultural and societal relevant ethical principles to orient national and international biomedical researchers working in Nigeria. It would complement other general research ethics and Good Clinical Practice modules. Participants suggested that awareness of the

Development and pilot testing of an online module for ethics education based on the Nigerian National Code for Health Research Ethics

Directory of Open Access Journals (Sweden)

Ogunrin Olubunmi A

2013-01-01

Full Text Available Abstract Background The formulation and implementation of national ethical regulations to protect research participants is fundamental to ethical conduct of research. Ethics education and capacity are inadequate in developing African countries. This study was designed to develop a module for online training in research ethics based on the Nigerian National Code of Health Research Ethics and assess its ease of use and reliability among biomedical researchers in Nigeria. Methodology This was a three-phased evaluation study. Phase one involved development of an online training module based on the Nigerian Code of Health Research Ethics (NCHRE and uploading it to the Collaborative Institutional Training Initiative (CITI website while the second phase entailed the evaluation of the module for comprehensibility, readability and ease of use by 45 Nigerian biomedical researchers. The third phase involved modification and re-evaluation of the module by 30 Nigerian biomedical researchers and determination of test-retest reliability of the module using Cronbach’s alpha. Results The online module was easily accessible and comprehensible to 95% of study participants. There were significant differences in the pretest and posttest scores of study participants during the evaluation of the online module (p = 0.001 with correlation coefficients of 0.9 and 0.8 for the pretest and posttest scores respectively. The module also demonstrated excellent test-retest reliability and internal consistency as shown by Cronbach’s alpha coefficients of 0.92 and 0.84 for the pretest and posttest respectively. Conclusion The module based on the Nigerian Code was developed, tested and made available online as a valuable tool for training in cultural and societal relevant ethical principles to orient national and international biomedical researchers working in Nigeria. It would complement other general research ethics and Good Clinical Practice modules. Participants

Development and pilot testing of an online module for ethics education based on the Nigerian National Code for Health Research Ethics.

Science.gov (United States)

Ogunrin, Olubunmi A; Ogundiran, Temidayo O; Adebamowo, Clement

2013-01-02

The formulation and implementation of national ethical regulations to protect research participants is fundamental to ethical conduct of research. Ethics education and capacity are inadequate in developing African countries. This study was designed to develop a module for online training in research ethics based on the Nigerian National Code of Health Research Ethics and assess its ease of use and reliability among biomedical researchers in Nigeria. This was a three-phased evaluation study. Phase one involved development of an online training module based on the Nigerian Code of Health Research Ethics (NCHRE) and uploading it to the Collaborative Institutional Training Initiative (CITI) website while the second phase entailed the evaluation of the module for comprehensibility, readability and ease of use by 45 Nigerian biomedical researchers. The third phase involved modification and re-evaluation of the module by 30 Nigerian biomedical researchers and determination of test-retest reliability of the module using Cronbach's alpha. The online module was easily accessible and comprehensible to 95% of study participants. There were significant differences in the pretest and posttest scores of study participants during the evaluation of the online module (p = 0.001) with correlation coefficients of 0.9 and 0.8 for the pretest and posttest scores respectively. The module also demonstrated excellent test-retest reliability and internal consistency as shown by Cronbach's alpha coefficients of 0.92 and 0.84 for the pretest and posttest respectively. The module based on the Nigerian Code was developed, tested and made available online as a valuable tool for training in cultural and societal relevant ethical principles to orient national and international biomedical researchers working in Nigeria. It would complement other general research ethics and Good Clinical Practice modules. Participants suggested that awareness of the online module should be increased through seminars

Development of efficient air-cooling strategies for lithium-ion battery module based on empirical heat source model

International Nuclear Information System (INIS)

Wang, Tao; Tseng, K.J.; Zhao, Jiyun

2015-01-01

Thermal modeling is the key issue in thermal management of lithium-ion battery system, and cooling strategies need to be carefully investigated to guarantee the temperature of batteries in operation within a narrow optimal range as well as provide cost effective and energy saving solutions for cooling system. This article reviews and summarizes the past cooling methods especially forced air cooling and introduces an empirical heat source model which can be widely applied in the battery module/pack thermal modeling. In the development of empirical heat source model, three-dimensional computational fluid dynamics (CFD) method is employed, and thermal insulation experiments are conducted to provide the key parameters. A transient thermal model of 5 × 5 battery module with forced air cooling is then developed based on the empirical heat source model. Thermal behaviors of battery module under different air cooling conditions, discharge rates and ambient temperatures are characterized and summarized. Varies cooling strategies are simulated and compared in order to obtain an optimal cooling method. Besides, the battery fault conditions are predicted from transient simulation scenarios. The temperature distributions and variations during discharge process are quantitatively described, and it is found that the upper limit of ambient temperature for forced air cooling is 35 °C, and when ambient temperature is lower than 20 °C, forced air-cooling is not necessary. - Highlights: • An empirical heat source model is developed for battery thermal modeling. • Different air-cooling strategies on module thermal characteristics are investigated. • Impact of different discharge rates on module thermal responses are investigated. • Impact of ambient temperatures on module thermal behaviors are investigated. • Locations of maximum temperatures under different operation conditions are studied.

Nice module. Apollon Solar present their new line of solar modules; Nettes Modul. Apollon Solar stellt Linie fuer neuartige Modultechnologie vor

Energy Technology Data Exchange (ETDEWEB)

Podewils, C.

2008-06-15

Solar modules, TGV engines and perfume Zerstaeuber seem to have nothing in common. The new solar module developed by French producer Apollon Solar makes use of both technologies in the construction process. The contribution presents the 'Nice' module which has many new features. (orig.)

Designing electronic module based on learning content development system in fostering students’ multi representation skills

Science.gov (United States)

Resita, I.; Ertikanto, C.

2018-05-01

This study aims to develop electronic module design based on Learning Content Development System (LCDS) to foster students’ multi representation skills in physics subject material. This study uses research and development method to the product design. This study involves 90 students and 6 physics teachers who were randomly chosen from 3 different Senior High Schools in Lampung Province. The data were collected by using questionnaires and analyzed by using quantitative descriptive method. Based on the data, 95% of the students only use one form of representation in solving physics problems. Representation which is tend to be used by students is symbolic representation. Students are considered to understand the concept of physics if they are able to change from one form to the other forms of representation. Product design of LCDS-based electronic module presents text, image, symbolic, video, and animation representation.

Development of a PET detector module incorporating a silicon photodiode array

International Nuclear Information System (INIS)

Rosenfeld, A.B.; Takacs, G.J.; Lerch, M.L.F.; Simmonds, P.E.

2000-01-01

Full text: We are developing a new Positron Emission Tomography (PET) detection sub-module with depth of interaction capability. The new sub-module is simple and robust to minimise module assembly complications and is completely independent of photomultiplier tubes. The new sub-module has also been designed to maximise its flexibility for easy sub-module coupling so as to form a complete, customised, detection module to be used in PET scanners dedicated to human brain and breast, and small animal studies. Blue enhanced, silicon 8x8 detector arrays are used to read out the scintillation crystals, and form the basis of the new module. The new detectors were designed by the Centre for Medical Radiation Physics (CMRP) at the University of Wollongong in collaboration with the High Energy Physics Department, University of Melbourne and produced by SPO D etector , Ukraine. Complementing the work on the silicon photodetectors, we have also carried out simulations of the propagation of the scintillation light in the crystals, and the effect of crystal dimensions and surface treatment on the distribution of light detected by the photodiode array. The distribution of light over the photodiodes has then been used to test various algorithms for calculating the point of interaction of the gamma ray in the crystal. Simulations of the light propagation show that for a crystal of dimensions 25mm x 25mm x 3mm, it is possible to determine the point of interaction in 2 dimensions with an average accuracy of just over 0.5mm. The resulting photon distribution detected by the array. The surface treatment, while having a large effect on the light output, does not have a great effect on the accuracy. If these dimensions change to 25mm x 25mm x 6mm then the surface conditions have a greater effect on the accuracy. It is possible however, with careful surface treatment, to achieve an accuracy of around 0.6mm, only marginally worse than the case for the 3mm thick crystal. Gamma ray

Revised upper limb module for spinal muscular atrophy: Development of a new module.

Science.gov (United States)

Mazzone, Elena S; Mayhew, Anna; Montes, Jacqueline; Ramsey, Danielle; Fanelli, Lavinia; Young, Sally Dunaway; Salazar, Rachel; De Sanctis, Roberto; Pasternak, Amy; Glanzman, Allan; Coratti, Giorgia; Civitello, Matthew; Forcina, Nicola; Gee, Richard; Duong, Tina; Pane, Marika; Scoto, Mariacristina; Pera, Maria Carmela; Messina, Sonia; Tennekoon, Gihan; Day, John W; Darras, Basil T; De Vivo, Darryl C; Finkel, Richard; Muntoni, Francesco; Mercuri, Eugenio

2017-06-01

There is a growing need for a robust clinical measure to assess upper limb motor function in spinal muscular atrophy (SMA), as the available scales lack sensitivity at the extremes of the clinical spectrum. We report the development of the Revised Upper Limb Module (RULM), an assessment specifically designed for upper limb function in SMA patients. An international panel with specific neuromuscular expertise performed a thorough review of scales currently available to assess upper limb function in SMA. This review facilitated a revision of the existing upper limb function scales to make a more robust clinical scale. Multiple revisions of the scale included statistical analysis and captured clinically relevant changes to fulfill requirements by regulators and advocacy groups. The resulting RULM scale shows good reliability and validity, making it a suitable tool to assess upper extremity function in the SMA population for multi-center clinical research. Muscle Nerve 55: 869-874, 2017. © 2016 Wiley Periodicals, Inc.

Test module development to detect the flase call probe pins on microeprocessor test equipment

Science.gov (United States)

Tang, L. W.; Ong, N. R.; Mohamad, I. S. B.; Alcain, J. B.; Retnasamy, V.

2017-09-01

Probe pins are useful for electrical testing of microelectronic components, printed circuit board assembly (PCBA), microprocessors and other electronic devices due to it provides the conductivity test based on specific device circuit design. During the repeatable test runs, the load of test modules, contact failures and the current conductivity induces layer wear off all the tip of probe pins contact. Contamination will be build-up on probe pins and increased contact resistivity which results of cost loss and time loss for rectifying programs, rectifying testers and exchanging new probe pins. In this study, a resistivity approach will be developed to provide "Testing of Test Probes". The test module based on "Four-wire Ohm measurement" method with two alternative ways of applying power supply, that are 9V from a single power supply and 5V from Arduino UNO power supply were demonstrated to measure the small resistance value of microprocessor probe pin. A microcontroller with VEE Pro software was used to record the measurement data. The accuracy of both test modules were calibrated under different temperature conditions and result shows that 9V from a single power supply test module has higher measurement accuracy.

Development and preliminary verification of 2-D transport module of radiation shielding code ARES

International Nuclear Information System (INIS)

Zhang Penghe; Chen Yixue; Zhang Bin; Zang Qiyong; Yuan Longjun; Chen Mengteng

2013-01-01

The 2-D transport module of radiation shielding code ARES is two-dimensional neutron and radiation shielding code. The theory model was based on the first-order steady state neutron transport equation, adopting the discrete ordinates method to disperse direction variables. Then a set of differential equations can be obtained and solved with the source iteration method. The 2-D transport module of ARES was capable of calculating k eff and fixed source problem with isotropic or anisotropic scattering in x-y geometry. The theoretical model was briefly introduced and series of benchmark problems were verified in this paper. Compared with the results given by the benchmark, the maximum relative deviation of k eff is 0.09% and the average relative deviation of flux density is about 0.60% in the BWR cells benchmark problem. As for the fixed source problem with isotropic and anisotropic scattering, the results of the 2-D transport module of ARES conform with DORT very well. These numerical results of benchmark problems preliminarily demonstrate that the development process of the 2-D transport module of ARES is right and it is able to provide high precision result. (authors)

Principles of Practical Training Organization in a Networking (Development of the Module "Psychological Prevention of Behavioral Disorders and Abnormalities in Development" as Example

Directory of Open Access Journals (Sweden)

Bogdanovich N. V.

2016-01-01

Full Text Available The article presents principles of inserting study subjects and practices in educational modules running with network organizations (internship sites. We proposed a methodological basis of the modular organization of educational process in the framework of the master's program, combied the activity, competence and psychotechnical approaches. Networking of leading chair and specially selected organizations providing the base for practical training solves the problem of organizing activity-related content of educational module. We discussed the main options for networking with the databases of practice and offered methodological principles of designing the educational practice-oriented module, wherein the main principle is the reflexive and activity character of networking. We proposed activity-based content of educational module "Psychological prevention of behavioral disorders and abnormalities in development", based on the substantial psychological definition of psychoprophylaxis as a directions of professional activity of the psychologist.

Development and Assessment of Modules to Integrate Quantitative Skills in Introductory Biology Courses.

Science.gov (United States)

Hoffman, Kathleen; Leupen, Sarah; Dowell, Kathy; Kephart, Kerrie; Leips, Jeff

2016-01-01

Redesigning undergraduate biology courses to integrate quantitative reasoning and skill development is critical to prepare students for careers in modern medicine and scientific research. In this paper, we report on the development, implementation, and assessment of stand-alone modules that integrate quantitative reasoning into introductory biology courses. Modules are designed to improve skills in quantitative numeracy, interpreting data sets using visual tools, and making inferences about biological phenomena using mathematical/statistical models. We also examine demographic/background data that predict student improvement in these skills through exposure to these modules. We carried out pre/postassessment tests across four semesters and used student interviews in one semester to examine how students at different levels approached quantitative problems. We found that students improved in all skills in most semesters, although there was variation in the degree of improvement among skills from semester to semester. One demographic variable, transfer status, stood out as a major predictor of the degree to which students improved (transfer students achieved much lower gains every semester, despite the fact that pretest scores in each focus area were similar between transfer and nontransfer students). We propose that increased exposure to quantitative skill development in biology courses is effective at building competency in quantitative reasoning. © 2016 K. Hoffman, S. Leupen, et al. CBE—Life Sciences Education © 2016 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

Perancangan Modul Penggajian Berbasis Odoo

OpenAIRE

Koeswanto, Vincent K. Edison; Yulia, Yulia; Adipranata, Rudy

2016-01-01

Human Resource Module is one of the modules owned by Odoo. One of the feature of this module is payroll. However, the features is not in accordance with the needs of companies in Indonesia in general. This causes the payroll system in Odoo not suitable to be implemented directly in the company.To solve these problems, author develop the payroll system in Human Resource module in Odoo. The development of this system is preceded by designing and analyze the payroll system at PT X. It also condu...

Teaching Concepts to Young Children Through Cultural Cooking Experiences. Bilingual/Bicultural Child Development Associate Pilot Project: Module XIV.

Science.gov (United States)

Smith, Teresa R.

This Child Development Associate (CDA) module, the fourteenth in a series of 16, suggests ways concepts can be taught by involving preschool children in carefully planned classroom cooking activities. Designed for bilingual/bicultural preschool teacher trainees, the module provides tips on food preparation as a learning experience. Required…

Children's Food and Drink Purchasing Behaviour "Beyond the School Gate": The Development of a Survey Module.

Science.gov (United States)

Wills, Wendy J; Macdiarmid, Jennie I; Masson, Lindsey F; Bromley, Catherine; Craig, Leone; McNeill, Geraldine

2013-01-01

Many children eat a diet which supplies a higher than recommended amount of nonmilk extrinsic sugars and saturated fatty acids. The school setting is often targeted for nutrition intervention as many children consume food at school. In Scotland, attempts have been made to improve the nutritional content of food in schools and attention has now turned to food and drink available "beyond the school gate." This paper describes the development of a module on food and drink purchasing behaviour. The Food Purchasing Module was designed to collect data, for the first time, from a representative sample of children aged 8-16 years about food and drinks purchased on the way to/from school, during break time/free periods, and at lunchtime, from outlets around schools. Cognitive testing of the module highlighted that younger children find self-completion questionnaires problematic. Older children have fewer problems with self-completion questionnaires but many do not follow question routing, which has implications for the delivery of future surveys. Development of this survey module adds much needed evidence about effectively involving children in surveys. Further research exploring food and drinks purchased beyond the school gate is needed to continue to improve the nutritional quality of children's diets.

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of building material integrated solar cell modules - high-durability roof modules); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (kotaikyusei yane module))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With the target set on a system with a roof array efficiency of 8.5%, and a system cost of 170 yen/W, development is being made on a large roof panel and its construction technology, which is capable of AC output by integrating into a large roof panel the compound thin film solar cells having glass/CdS/CdTe/rear air chamber/rear metal, and the inverter. In the cell constituting materials and the structure design, sealants were evaluated, the painting process was developed, and two kinds of structures were prepared. The frameless type has a lamination structure, and a prototype module of 886 times 664 mm was fabricated, and the frame type has a double sealing structure, and a prototype module 600 times 900 mm was fabricated. Prototype modules that can be fixed on a rail type fixing stand were fabricated and constructed, having demonstrated sufficient workability. In addition, a prototype small inverter with system coordination protection was operated actually, and the initial stage malfunctions were corrected. Two demonstration buildings were built, and the whole process was performed from assembly and transportation of the modules and to the installation thereof at the construction site. (NEDO)

The State of the Art Report on the Development and Manufacturing Technology of Test Blanket Module

International Nuclear Information System (INIS)

Lee, J. S.; Jeong, Y. H.; Park, S. Y.; Lee, M. H.; Choi, B. K.; Baek, J. H.; Park, J. Y.; Kim, J. H.; Kim, H. G.; Kim, K. H.

2006-07-01

The main objective of the present R and D on breeder blanket is the development of test blanket modules (TBMs) to be installed and tested in International Thermonuclear Experimental Reactor (ITER). In the program of the blanket development, a blanket module test in the ITER is scheduled from the beginning of the ITER operation, and the performance test of TBM in ITER is the most important milestone for the development of the DEMO blanket. The fabrication of TBMs has been required to test the basic performance of the DEMO blanket, i.e., tritium production/recovery, high-grade heat generation and radiation shielding. Therefore, the integration of the TBM systems into ITER has been investigated with the aim to check the safety, reliability and compatibility under nuclear fusion state. For this reason, in the Test Blanket Working Group (TBWG) as an activity of the International Energy Association (IEA), a variety of ITER TBMs have been proposed and investigated by each party: helium-cooled ceramic (WSG-1), helium-cooled LiPb (WSG-2), water-cooled ceramic (WSG-3), self-cooled lithium (WSG-4) and self-cooled molten salt (WSG-5) blanket systems. Because we are still deficient in investigation of TBM development, the need of development became pressing. In this report, for the development of TBM sub-module and mock-up, it is necessary to analyze and examine the state of the art on the development of manufacturing technology of TBM in other countries. And we will be applied as basic data to establish a manufacturing technology

Modulation of GABAergic Transmission in Development and Neurodevelopmental Disorders: Investigating Physiology and Pathology to Gain Therapeutic Perspectives

Directory of Open Access Journals (Sweden)

Gabriele eDeidda

2014-05-01

Full Text Available During mammalian ontogenesis, the neurotransmitter GABA is a fundamental regulator of neuronal networks. In neuronal development, GABAergic signaling regulates neural proliferation, migration, differentiation, and neuronal-network wiring. In the adult, GABA orchestrates the activity of different neuronal cell-types largely interconnected, by powerfully modulating synaptic activity. GABA exerts these functions by binding to chloride-permeable ionotropic GABAA receptors and metabotropic GABAB receptors. According to its functional importance during development, GABA is implicated in a number of neurodevelopmental disorders such as autism, Fragile X, Rett syndrome, Down syndrome, schizophrenia, Tourette's syndrome and neurofibromatosis.The strength and polarity of GABAergic transmission is continuously modulated during physiological, but also pathological conditions. For GABAergic transmission through GABAA receptors, strength regulation is achieved by different mechanisms such as modulation of GABAA receptors themselves, variation of intracellular chloride concentration, and alteration in GABA metabolism. In the never-ending effort to find possible treatments for GABA-related neurological diseases, of great importance would be modulating GABAergic transmission in a safe and possibly physiological way, without the dangers of either silencing network activity or causing epileptic seizures. In this review, we will discuss the different ways to modulate GABAergic transmission normally at work both during physiological and pathological conditions. Our aim is to highlight new research perspectives for therapeutic treatments that reinstate natural and physiological brain functions in neuro-pathological conditions.

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development of novel type solar cell module integratable with building materials - Highly durable roof module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu - kotaikyusei yane module)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A thin-film solar array, a large roof panel, and an interconnecting power conditioner are integrated into one and single structural member for the development of a residential photovoltaic power system in which a unit AC (alternating current) output is collected from each panel. In fiscal 1999, in the study of highly durable materials for solar cell modules and of their structure, a thin film compound solar cell module was enlarged to 82cm times 71cm, evaluated for performance, and installed on the third test house. In the study of collecting AC power from the solar cell module, a compact power conditioner for a roof panel which had been in test operation on the roof of the laboratory since 1998 was checked for practical performance, improved, and evaluated for system generation efficiency. In the study of a highly durable roof module structure, problems pertaining to heat radiation from the rear side steel sheet, the burning of the junction box, etc., were solved, and the module passed a verification test under the Building Standard Law. In the validation of the roof module for which power generation performance and meteorological conditions had already been continuously measured for 19 months, it was found that the roof module suffered no troubles such as water leak or deformation. (NEDO)

Magneto-optic and electro-optic modulators

International Nuclear Information System (INIS)

Hutchinson, D.P.; Ma, C.H.; Price, T.R.; Staats, P.A.; Vander Sluis, K.L.

1982-01-01

An important aspect of the Faraday rotation diagnostic for tokamak plasma measurements has been the development of suitable polarization modulators for submillimeter wavelengths. The problems are to obtain high optical transmission and fast modulation frequencies. At ORNL we have developed both a magneto-optic and an electro-optic submillimeter-wave modulators. These devices have been operated at modulation frequencies of approximately 100 kHz and both have high transmission

Development of Ethnoscience Approach in The Module Theme Substance Additives to Improve the Cognitive Learning Outcome and Student’s entrepreneurship

Science.gov (United States)

Sudarmin; Febu, R.; Nuswowati, M.; Sumarni, W.

2017-04-01

Ethnoscience approach is an interesting research today. The purpose of this research is to develop approaches ethnoscience and modules ethnoscience theme additives based ethnoscience; as well as assess the feasibility and effectiveness of module theme additives based ethnoscience to improve learning outcomes and the entrepreneurial character of students. This type of research is the Research and Development (R & D). In this research consist of four stages, namely define, design, development and implementation. The subjects of this study were students of the School of MTs Maarif NU Brebes. Data were analyzed by descriptive qualitative and quantitative. The results showed that ethnoscience approach and the module theme substance additives used declared worthy of National Education Standards Agency (BNSP) with an average percentage of validation on the feasibility aspect of the content, language feasibility, and feasibility of presenting respectively for 94.3%, 86 % and 92% and a very decent entry criteria. The effect of the application modules substance additive based ethnoscience can improve on the cognitive learning classical amounted to 90.63%, and increased learning outcomes category was based on the scores of N-gain. Influence ethnoscience approach application and module theme substances additives based ethnoscience able to improve the entrepreneurial character of students. Based on the results of this study concluded that the ethnoscience approach and module theme substance additives based ethnoscience effective to improve learning outcomes and students’ entrepreneurship.

Dual Arm Work Module Development and Appplications

Energy Technology Data Exchange (ETDEWEB)

Noakes, M.W.

1999-04-25

The dual arm work module (DAWM) was developed at Oak Ridge National Laboratory (ORNL) by the Robotics Technology Development Program (RTDP) as a development test bed to study issues related to dual arm manipulation, including platform cotilguration, controls, automation, operations, and tooling. The original platform was based on two Schilling Titan II manipulators mounted to a 5-degree-of- freedom (DOF) base fabricated by RedZone Robotics, Inc. The 5-DOF articulation provided a center torso rotation, linear actuation to change the separation between the arms, and arm base rotation joints to provide "elbows up," elbows down," or "elbows out" orientation. A series of tests were conducted on operations, tooling, and task space scene analysis (TSSA)-driven robotics for overhead transporter- mounted and crane hook-deployed scenarios. A concept was developed for DAWM deployment from a large remote work vehicle, but the project was redirected to support dismantlement of the Chicago Pile #5 (CP-5) reactor at Argonne National Laboratory in fiscal year (FY) 1997. Support of CP-5 required a change in focus of the dual arm technology from that of a development test bed to a system focussed for a specific end user. ORNL teamed with the Idaho National Environmental ,Engineering Laboratory, Sandia National Laboratory, and the Savannah River Technology Center to deliver a crane-deployed derivative of the DAWM, designated the dual arm work platform (DAWP). RTDP staff supported DAWP at CP-5 for one FY; Argonne staff continued operation through to dismantlement of the reactor internals. Lessons learned from this interaction were extensive. Beginning in FY 1999, dual arm development activities are again being pursued in the context of those lessons learned. This paper describes the progression of philosophy of the DAWM from initial test bed to lessons learned through interaction at CP-5 and to the present investigation of telerobotic assist of teleoperation and TSSA- driven robotics.

Development of a novel fast frequency modulation scheme for the JET multi-channel reflectometer

International Nuclear Information System (INIS)

Deliyanakis, N.

1999-10-01

A novel frequency modulation scheme has been developed for the multi-channel reflectometer used to measure density profiles and density fluctuations on the JET tokamak. This reflectometer normally uses slow frequency sweeping, combined with fixed-frequency operation, to measure the group delay, as well as plasma fluctuations, at 10 different microwave frequencies. The novel scheme uses continuous frequency modulation on a time-scale much faster than that of plasma fluctuations, the main aim being to make the group delay measurement more robust against plasma fluctuations. This paper discusses the theoretical background of the scheme, gives a detailed description of the system, and presents results from plasma measurements. (author)

Development of a 64-channel 100 ps TDC module

International Nuclear Information System (INIS)

Liu Xiaohua; An Qi; Liu Shubin; Su Hong; Zhan Wenlong

2009-01-01

Multi-wire drift chamber at external target experiment in HIRFL-CSR measures drift time of charged particles to obtain the track information. A 64-channel TDC module hosting high density connectors and high performance TDC chips (HPTDC) are used to perform the time digitization. Data of the module is transferred to computer through PXI bus. The test results show that a 100 ps resolution has been achieved. (authors)

An innovative "ChemicalVia" process for the production of high density interconnect printed circuit boards The ATLAS muon chamber quality control with the X-ray tomograph at CERN

CERN Document Server

Da Silva, Vitor; Watts, David; Van der Bij, Erik; Banhidi, Z; Berbiers, Julien; Lampl, W; Marchesotti, M; Rangod, Stephane; Sbrissa, E; Schuh, S; Voss, Rüdiger; Zhuravlov, V

2004-01-01

The ChemicalVia process, patented by CERN, provides a new method of making microvias in high-density multilayer printed circuit boards of different types, such as sequential build-up (SBU), high density interconnected (HDI), or laminated multi-chip modules (MCM-L). The process uses chemical etching instead of laser, plasma or other etching techniques and can be implemented in a chain production line. This results in an overall reduced operation and maintenance cost and a much shorter hole production time as compared with other microvia processes. copy Emerald Group Publishing Limited. 4 Refs.4 An essential part of the Muon Spectrometer of the ATLAS experiment is based on the Monitored Drift Tube (MDT) technology. About 1200 muon drift chambers are being built at 13 institutes all over the world. The MDT chambers require an exceptional mechanical construction accuracy of better than 20 mu m. A dedicated X-ray tomograph has been developed at CERN since 1996 to control the mechanical quality of the chambers. The...

ATLAS calorimetry: Trigger, simulation and jet calibration

CERN Document Server

Weber, Pavel

2008-01-01

The Pre-Processor system of the ATLAS Level-1 Calorimeter Trigger performs complex processing of analog trigger tower signals from electromagnetic and hadronic calorimeters. The main processing block of the Pre-Processor System is the Multi-Chip Module (MCM). The first part of this thesis describes MCM quality assurance tests that have been developed, their use in the MCM large scale production and the results that have been obtained. In the second part of the thesis a validation of a shower parametrisation model for the ATLAS fast simulation package ATLFAST based on QCD dijet events is performed. A detailed comparison of jet response and jet energy resolution between the fast and the full simulation is presented. The uniformity of the calorimeter response has a significant impact on the accuracy of the jet energy measurement. A study of the calorimeter intercalibration using QCD dijet events is presented in the last part of the thesis. The intercalibration study is performed in azimuth angle phi and in pseud...

Development of an x-ray klystron modulator with a pulse-forming line and magnetic switch

International Nuclear Information System (INIS)

Akemoto, M.; Takeda, S.

1992-01-01

A new type of klystron modulator has been developed for the Japan Linear Collider. It consists of a pulse-forming line (PFL), a pulse transformer and a magnetic switch. In order to realize a compact modulator, a triplate strip transmission line using deionized water as a dielectric was adapted. An Fe amorphous core was used for the magnetic switch and the pulse transformer to reduce the size and cost. A preliminary test has shown that an output pulse with a peak voltage of 550 kV, a pulse length (flat-top) of 440 ns and a rise time of 165 ns can be generated for a dummy load with an impedance of 412Ω. It was also experimentally confirmed that the power efficiency of the modulator is approximately 83%. (Author) 7 figs., 3 tabs., 2 refs

Development of active learning modules in pharmacology for small group teaching.

Science.gov (United States)

Tripathi, Raakhi K; Sarkate, Pankaj V; Jalgaonkar, Sharmila V; Rege, Nirmala N

2015-01-01

Current teaching in pharmacology in undergraduate medical curriculum in India is primarily drug centered and stresses imparting factual knowledge rather than on pharmacotherapeutic skills. These skills would be better developed through active learning by the students. Hence modules that will encourage active learning were developed and compared with traditional methods within the Seth GS Medical College, Mumbai. After Institutional Review Board approval, 90 second year undergraduate medical students who consented were randomized into six sub-groups, each with 15 students. Pre-test was administered. The three sub-groups were taught a topic using active learning modules (active learning groups), which included problems on case scenarios, critical appraisal of prescriptions and drug identification. The remaining three sub-groups were taught the same topic in a conventional tutorial mode (tutorial learning groups). There was crossover for the second topic. Performance was assessed using post-test. Questionnaires with Likert-scaled items were used to assess feedback on teaching technique, student interaction and group dynamics. The active and tutorial learning groups differed significantly in their post-test scores (11.3 ± 1.9 and 15.9 ± 2.7, respectively, P active learning session as interactive (vs. 37/90 students in tutorial group) and enhanced their understanding vs. 56/90 in tutorial group), aroused intellectual curiosity (47/90 students of active learning group vs. 30/90 in tutorial group) and provoked self-learning (41/90 active learning group vs. 14/90 in tutorial group). Sixty-four students in the active learning group felt that questioning each other helped in understanding the topic, which was the experience of 25/90 students in tutorial group. Nevertheless, students (55/90) preferred tutorial mode of learning to help them score better in their examinations. In this study, students preferred an active learning environment, though to pass examinations, they

Development of prototype luminosity detector modules for future experiments on linear colliders

CERN Document Server

AUTHOR|(CDS)2081248; Idzik, Marek

The main objective of this dissertation is to develop and validate the prototype module of the LumiCal luminosity detector. The dissertation presents the works executed from the first detector concept, through all subsequent R&D stages, ending with the test beam results obtained using the complete detector module. Firstly, the linear electron positron colliders and planned experiments are introduced, together with their role in our understanding of the basis of matter and sensing for the New Physics. The signal extraction from radiation sensors and further signal processing techniques are discussed in chapter 2. Besides the commonly accepted techniques of amplitude and time measurements, a novel readout implementation, utilizing digital signal processing and deconvolution principle, is proposed, and its properties are analyzed in details. The architecture, design, and measurements of the LumiCal readout chain components are presented in chapter 3. A dedicated test setups prepared for their parameterizatio...

Progress on the WOM (Wavelength-shifting optical module) development for IceCube

Energy Technology Data Exchange (ETDEWEB)

Hebecker, Dustin [DESY Zeuthen (Germany)

2015-07-01

For ongoing studies for the extension of the IceCube neutrino observatory to low energies (PINGU) and high energies the noise rate of the optical modules should be decreased and the effective area increased in order to improve energy resolution and overall sensitivity. The WOM (Wavelength-shifting optical module) targets this points by expanding the capture area while decreasing the size of the PMT and thus decreasing the noise rate. Photons are first captured in an organic wavelength-shifting material (WLS) that is coated on light guiding material to guide the light to two smaller PMTs. This allows to achieve a very large collection area and reduces the noise to the order of 10 Hz in comparison to 600-800 Hz (IceCube DOM). The progress on the necessary WLS paint development and substrate selection will be presented. Also a brief status / outlook on the prototype assembly will be given.

SUPPORT CARD FOR THE FORWARD SCT MODULE

CERN Document Server

Greenall, A

2002-01-01

Previously in the development and testing stage of ATLAS SCT Forward modules support cards have been used which interface the module to the DAQ by using only the Redundant inputs for the module configuration and the 'spying' of the ABCD Master chip(s) data. As module development has matured there is now a necessity to be able to test modules in the laboratory using also their Primary input/output data routes i.e. using the optical chips DORIC [1] and VDC [2] but without the need of optical fibres. A Forward Kapton Support Card, FKSC, has been developed so that both Primary and Redundant data routes can be used for module testing.

Development of an advanced static feed water electrolysis module. [for spacecraft

Science.gov (United States)

Schubert, F. H.; Wynveen, R. A.; Jensen, F. C.; Quattrone, P. D.

1975-01-01

A Static Feed Water Electrolysis Module (SFWEM) was developed to produce 0.92 kg/day (2.0 lb/day) of oxygen (O2). Specific objectives of the program's scope were to (1) eliminate the need for feed water cavity degassing, (2) eliminate the need for subsystem condenser/separators, (3) increase current density capability while decreasing electrolysis cell power (i.e., cell voltage) requirements, and (4) eliminate subsystem rotating parts and incorporate control and monitor instrumentation. A six-cell, one-man capacity module having an active area of 0.00929 sq m (0.10 sq ft) per cell was designed, fabricated, assembled, and subjected to 111 days (2664 hr) of parametric and endurance testing. The SFWEM was successfully operated over a current density range of 0 to 1076 mA/sq cm (0 to 1000 ASF), pressures of ambient to 2067 kN/sq m (300 psia), and temperatures of ambient to 366 K (200 F). During a 94-day endurance test, the SFWEM successfully demonstrated operation without the need for feed water compartment degassing.

Design and Development of Multi-Transceiver Lorafi Board consisting LoRa and ESP8266-Wifi Communication Module

Science.gov (United States)

Azmi, Noraini; Sudin, Sukhairi; Munirah Kamarudin, Latifah; Zakaria, Ammar; Visvanathan, Retnam; Chew Cheik, Goh; Mamduh Syed Zakaria, Syed Muhammad; Abdullah Alfarhan, Khudhur; Badlishah Ahmad, R.

2018-03-01

The advancement of Micro-Electro-Mechanical-Systems (MEMS), microcontroller technologies and the idea of Internet of Things (IoT) motivates the development of wireless modules (e.g. WiFi, Bluetooth, Zigbee, and LoRa) that are small and affordable. This paper aims to provide detailed information on the development of the LoRaFi board. The LoRaFi 1.0 is a multi-protocol communication board developed by Centre of Excellence for Advanced Sensor Technology (CEASTech). The board was developed for but not limited to monitor the indoor air quality. The board comprises two different wireless communication modules namely, Long-range technology (LoRa) and WiFi (using ESP8266). The board can be configured to communicate either using LoRa or WiFi or both. The board has been tested and the wireless communication operates successfully. Apart from LoRa, WiFi enables data to be forwarded to the cloud/server where the data can be stored for further data analysis. This helps provide users with real-time information on their smartphones or other applications. In the future, researchers will conduct tests to investigate the communication link quality. Newer version with reduced board size and additional wireless communication module will be developed in the future as to increase board flexibility and widen the range of applications that can use the board.

Development of the severe accident management guidance module for the SATS training simulator

International Nuclear Information System (INIS)

Kim, K. R.; Park, S. H.; Kim, D. H.

2004-01-01

Recently KAERI has developed severe accident management guidance to establish Korea standard severe accident management system. On the other hand PC-based severe accident training simulator SATS has been developed, which uses MELCOR computing code as the simulation engine. SATS graphically displays and simulates the severe accident progression with interactive user inputs. The control capability of SATS makes a severe accident training course more interesting and effective. In this paper the development and functions of HyperKAMG module are explained. Furthermore easiness and effectiveness of the HyperKAMG-SATS system in severe accident management are described

Development of Calculation Module for Intake Retention Functions based on Occupational Intakes of Radionuclides

Energy Technology Data Exchange (ETDEWEB)

Noh, Siwan; Kwon, Tae-Eun; Lee, Jai-Ki [Hanyang Univ., Seoul (Korea, Republic of); Lee, Jong-Il; Kim, Jang-Lyul [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-10-15

In internal dosimetry, intake retention and excretion functions are essential to estimate intake activity using bioassay sample such as whole body counter, lung counter, and urine sample. Even though ICRP (International Commission on Radiological Protection)provides the functions in some ICRP publications, it is needed to calculate the functions because the functions from the publications are provided for very limited time. Thus, some computer program are generally used to calculate intake retention and excretion functions and estimate intake activity. OIR (Occupational Intakes of Radionuclides) will be published soon by ICRP, which totally replaces existing internal dosimetry models and relevant data including intake retention and excretion functions. Thus, the calculation tool for the functions is needed based on OIR. In this study, we developed calculation module for intake retention and excretion functions based on OIR using C++ programming language with Intel Math Kernel Library. In this study, we developed the intake retention and excretion function calculation module based on OIR using C++ programing language.

Development of Calculation Module for Intake Retention Functions based on Occupational Intakes of Radionuclides

International Nuclear Information System (INIS)

Noh, Siwan; Kwon, Tae-Eun; Lee, Jai-Ki; Lee, Jong-Il; Kim, Jang-Lyul

2014-01-01

In internal dosimetry, intake retention and excretion functions are essential to estimate intake activity using bioassay sample such as whole body counter, lung counter, and urine sample. Even though ICRP (International Commission on Radiological Protection)provides the functions in some ICRP publications, it is needed to calculate the functions because the functions from the publications are provided for very limited time. Thus, some computer program are generally used to calculate intake retention and excretion functions and estimate intake activity. OIR (Occupational Intakes of Radionuclides) will be published soon by ICRP, which totally replaces existing internal dosimetry models and relevant data including intake retention and excretion functions. Thus, the calculation tool for the functions is needed based on OIR. In this study, we developed calculation module for intake retention and excretion functions based on OIR using C++ programming language with Intel Math Kernel Library. In this study, we developed the intake retention and excretion function calculation module based on OIR using C++ programing language

Development of a remotely maintainable radio-frequency module for the Compact Ignition Tokamak

International Nuclear Information System (INIS)

Snider, J.D.

1988-01-01

The Compact Ignition Tokamak (CIT) will require reliable remote handling (RH) systems to overcome failures in diagnostic and operational equipment. Oak Ridge National laboratory (ORNL) is responsible for the ex-vessel remote maintenance systems for the CIT. Part of this effort is performing remote maintenance demonstrations on replicas of various CIT equipment. To ensure successful RH, the machine must be designed with proven remote maintenance features. In the demonstrations, critical remote maintenance features are tested before actual CIT equipment designs are finalized. Designs and procedures required to remotely remove and install a radio-frequency (rf) module from a modplane port on the tokamak were recently demonstrated at ORNL. This testing identified both successful design features for remote maintenance of the rf module and areas that require further development. 1 ref., 11 figs

Selective androgen receptor modulators in preclinical and clinical development.

Science.gov (United States)

Narayanan, Ramesh; Mohler, Michael L; Bohl, Casey E; Miller, Duane D; Dalton, James T

2008-01-01

Androgen receptor (AR) plays a critical role in the function of several organs including primary and accessory sexual organs, skeletal muscle, and bone, making it a desirable therapeutic target. Selective androgen receptor modulators (SARMs) bind to the AR and demonstrate osteo- and myo-anabolic activity; however, unlike testosterone and other anabolic steroids, these nonsteroidal agents produce less of a growth effect on prostate and other secondary sexual organs. SARMs provide therapeutic opportunities in a variety of diseases, including muscle wasting associated with burns, cancer, or end-stage renal disease, osteoporosis, frailty, and hypogonadism. This review summarizes the current standing of research and development of SARMs, crystallography of AR with SARMs, plausible mechanisms for their action and the potential therapeutic indications for this emerging class of drugs.

Research and development of system to utilize photovoltaic energy. Survey on the specific purpose modules; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoto module ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on the specific purpose modules for photovoltaic power generation in fiscal 1994. (1) On the feasibility survey on new application fields, it was clarified that photovoltaic power generation is applicable to extensive areas such as farmland, road, railway and public facility as latent demand sites. (2) On the optimum modules for various specific purposes, the structure, production method, cost estimation and issues of various modules were studied for desert, wasteland, coast, ocean, river, embankment, railway, road, mobile facility and arcade. (3) On the survey on new materials and material development, various conventional materials and materials promising for required performance were surveyed for every application. (4) On the survey on technology trends, the survey members participated in the first international photovoltaic energy conversion conference and the photovoltaic power generation workshop, while the members held the 1st-5th specific purpose module subcommittees. 1 tab.

Low-cost solar module manufacturing

International Nuclear Information System (INIS)

Little, Roger G.; Nowlan, Michael J.; Matthei, Keith W.; Darkazalli, Ghazi

1997-01-01

As the market for terrestrial photovoltaic modules expands beyond the 80 MW per year level, module manufacturers are adopting a number of cost-reduction strategies, including the use of higher throughput equipment, increased process automation, and the fabrication of larger area cells and modules. This paper reviews recent activities at Spire Corporation in the development of advanced module manufacturing and testing equipment

Characterization and Diagnostics for Photovoltaic Modules and Arrays

DEFF Research Database (Denmark)

Spataru, Sergiu

part of this work were developed based on two well-known module characterization techniques, namely current-voltage (I-V) characterization, and electroluminescence imaging. he I-V based module diagnostic methods were developed by combining the strengths of light I-V and dark I-V characterization......, characterization and diagnostic methods are increasingly important in identifying and understanding the failures and degradation modes affecting PV modules and arrays, as well as developing relevant tools and tests for assessing the reliability and lifetime of PV modules. This thesis investigates diagnostic...... methods for characterizing and detecting degradation modes in crystalline silicon photovoltaic modules and arrays, and is structured into two parts. The first part of this work is focused on developing PV module characterization and diagnostic methods for use in module diagnostics and failure...

Space station common module network topology and hardware development

Science.gov (United States)

Anderson, P.; Braunagel, L.; Chwirka, S.; Fishman, M.; Freeman, K.; Eason, D.; Landis, D.; Lech, L.; Martin, J.; Mccorkle, J.

1990-01-01

Conceptual space station common module power management and distribution (SSM/PMAD) network layouts and detailed network evaluations were developed. Individual pieces of hardware to be developed for the SSM/PMAD test bed were identified. A technology assessment was developed to identify pieces of equipment requiring development effort. Equipment lists were developed from the previously selected network schematics. Additionally, functional requirements for the network equipment as well as other requirements which affected the suitability of specific items for use on the Space Station Program were identified. Assembly requirements were derived based on the SSM/PMAD developed requirements and on the selected SSM/PMAD network concepts. Basic requirements and simplified design block diagrams are included. DC remote power controllers were successfully integrated into the DC Marshall Space Flight Center breadboard. Two DC remote power controller (RPC) boards experienced mechanical failure of UES 706 stud-mounted diodes during mechanical installation of the boards into the system. These broken diodes caused input to output shorting of the RPC's. The UES 706 diodes were replaced on these RPC's which eliminated the problem. The DC RPC's as existing in the present breadboard configuration do not provide ground fault protection because the RPC was designed to only switch the hot side current. If ground fault protection were to be implemented, it would be necessary to design the system so the RPC switched both the hot and the return sides of power.

Development and evaluation of learning module on clinical decision-making in Prosthodontics.

Science.gov (United States)

Deshpande, Saee; Lambade, Dipti; Chahande, Jayashree

2015-01-01

Best practice strategies for helping students learn the reasoning skills of problem solving and critical thinking (CT) remain a source of conjecture, particularly with regard to CT. The dental education literature is fundamentally devoid of research on the cognitive components of clinical decision-making. This study was aimed to develop and evaluate the impact of blended learning module on clinical decision-making skills of dental graduates for planning prosthodontics rehabilitation. An interactive teaching module consisting of didactic lectures on clinical decision-making and a computer-assisted case-based treatment planning software was developed Its impact on cognitive knowledge gain in clinical decision-making was evaluated using an assessment involving problem-based multiple choice questions and paper-based case scenarios. Mean test scores were: Pretest (17 ± 1), posttest 1 (21 ± 2) and posttest 2 (43 ± 3). Comparison of mean scores was done with one-way ANOVA test. There was overall significant difference in between mean scores at all the three points (P posttest 1 > pretest. Blended teaching methods employing didactic lectures on the clinical decision-making as well as computer assisted case-based learning can be used to improve quality of clinical decision-making in prosthodontic rehabilitation for dental graduates.

Developing effective web-based regional anesthesia education: a randomized study evaluating case-based versus non-case-based module design.

Science.gov (United States)

Kopp, Sandra L; Smith, Hugh M

2011-01-01

. Although residents believe that online learning should be used in anesthesia training, the results of this study do not demonstrate improved learning or justify the time and expense of developing complex case-based training modules. While there may be practical benefits of Web-based education, educators in regional anesthesia should be cautious about developing curricula based on learner preference data.

Method for Backplane Data Communication with the VME Rear Transition Modules Developed for the ATLAS FTK Project

CERN Document Server

Bogdan, M; The ATLAS collaboration; Piendibene, M; Shochet, M; Tompkins, L

2013-01-01

This paper presents a method to achieve backplane data transfer capabilities to and from a VME Rear Transition Module (RTM), while being in full compliance with the VME64/VIPA Specification. The VMEbus is specified for data transfers only with boards plugged on the front side of the subrack. The RTMs receive power from the crate, but are not part of the actual data transfer bus. They do not plug into the J1 connector, and have no access to backplane interface logic. In this implementation, the RTM uses the feed-through pins located in the J2 connector to communicate with the corresponding front module. The front module's internal data, address, and control buses are extended to the rear. This allows the front module's interface block to control data transfers for logic devices on both sides of the same slot. All usual VME protocols to logic devices on the RTM become possible without any software adaptation. This method was implemented on several prototype modules developed for the ATLAS FTK Project. The full ...

Evaluation of a personal and professional development module in an undergraduate medical curriculum in India

Directory of Open Access Journals (Sweden)

Ramnarayan Komattil

2016-03-01

Full Text Available The study aimed at evaluating the personal and professional development (PPD module in the undergraduate medical curriculum in Melaka Manipal Medical College, India. PPD hours were incorporated in the curriculum. A team of faculty members and a faculty coordinator identified relevant topics and students were introduced to topics such as medical humanities, leadership skills, communication skills, ethics, professional behavior, and patient narratives. The module was evaluated using a prevalidated course feedback questionnaire which was administered to three consecutive batches of students from March 2011 to March 2013. To analyze faculty perspectives, one to one in-depth interviews and focus group discussions were conducted by the coordinators with faculty members who conducted the PPD classes. Analysis of the course feedback form revealed that majority (80% of students agreed that the module was well prepared and was "highly relevant" to the profession. Faculty found the topics new and interdisciplinary and there was a sense of sharing responsibility and workload by the faculty. PPD modules are necessary components of the curriculum and help to mould students while they are still acquiescent as they assume their roles as doctors of the future.

Intrathymic immune modulation prevents acute rejection but not the development of graft arteriosclerosis (chronic rejection)

NARCIS (Netherlands)

Hillebrands, JL; Raue, HP; Klatter, FA; Hylkema, MN; Platteel, [No Value; Hardonk-Wubbena, A; Nieuwenhuis, P; Rozing, J

2001-01-01

Background. We showed previously that our intrathymic immune modulation protocol induces virtually permanent graft survival of simultaneously transplanted cardiac allografts in MHC-incompatible rat strain combinations. It is, however, unknown whether this procedure prevents the development of graft

Children's Food and Drink Purchasing Behaviour “Beyond the School Gate”: The Development of a Survey Module

Science.gov (United States)

Wills, Wendy J.; Macdiarmid, Jennie I.; Masson, Lindsey F.; McNeill, Geraldine

2013-01-01

Many children eat a diet which supplies a higher than recommended amount of nonmilk extrinsic sugars and saturated fatty acids. The school setting is often targeted for nutrition intervention as many children consume food at school. In Scotland, attempts have been made to improve the nutritional content of food in schools and attention has now turned to food and drink available “beyond the school gate.” This paper describes the development of a module on food and drink purchasing behaviour. The Food Purchasing Module was designed to collect data, for the first time, from a representative sample of children aged 8–16 years about food and drinks purchased on the way to/from school, during break time/free periods, and at lunchtime, from outlets around schools. Cognitive testing of the module highlighted that younger children find self-completion questionnaires problematic. Older children have fewer problems with self-completion questionnaires but many do not follow question routing, which has implications for the delivery of future surveys. Development of this survey module adds much needed evidence about effectively involving children in surveys. Further research exploring food and drinks purchased beyond the school gate is needed to continue to improve the nutritional quality of children's diets. PMID:24959546

Digital front-end module (DFEM) series; Digital front end module (DFEM) series

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The digital front-end module (DFEM) is a module in which the processes ranging from the reception of digitally modulated radiofrequencies to the output of digital IF (Intermediate Frequency) signals or data streams are integrated. Beginning with a module for the MCNS (Multimedia Cable Network System) cable modem which was the first module in this business field approved by the Cable Labs, U.S., Toshiba has developed a series of DFEMs for various digital media for satellites, ground waves, and CATV (Cable Television) systems. The series is characterized by (1) the serialization of DFEMs compatible with various digital modulation techniques such as 8 PSK (Phase Shift Keying), OFDM (Orthogonal Frequency Division Multiplexing), and 256 QAM (Quadrature Amplitude Modulation), (2) easy connection with digital circuits thanks to the high shielding effect, and (3) the achievement of smaller size, higher performance, and lower power consumption. (translated by NEDO)

Development of CAD-Based Geometry Processing Module for a Monte Carlo Particle Transport Analysis Code

International Nuclear Information System (INIS)

Choi, Sung Hoon; Kwark, Min Su; Shim, Hyung Jin

2012-01-01

As The Monte Carlo (MC) particle transport analysis for a complex system such as research reactor, accelerator, and fusion facility may require accurate modeling of the complicated geometry. Its manual modeling by using the text interface of a MC code to define the geometrical objects is tedious, lengthy and error-prone. This problem can be overcome by taking advantage of modeling capability of the computer aided design (CAD) system. There have been two kinds of approaches to develop MC code systems utilizing the CAD data: the external format conversion and the CAD kernel imbedded MC simulation. The first approach includes several interfacing programs such as McCAD, MCAM, GEOMIT etc. which were developed to automatically convert the CAD data into the MCNP geometry input data. This approach makes the most of the existing MC codes without any modifications, but implies latent data inconsistency due to the difference of the geometry modeling system. In the second approach, a MC code utilizes the CAD data for the direct particle tracking or the conversion to an internal data structure of the constructive solid geometry (CSG) and/or boundary representation (B-rep) modeling with help of a CAD kernel. MCNP-BRL and OiNC have demonstrated their capabilities of the CAD-based MC simulations. Recently we have developed a CAD-based geometry processing module for the MC particle simulation by using the OpenCASCADE (OCC) library. In the developed module, CAD data can be used for the particle tracking through primitive CAD surfaces (hereafter the CAD-based tracking) or the internal conversion to the CSG data structure. In this paper, the performances of the text-based model, the CAD-based tracking, and the internal CSG conversion are compared by using an in-house MC code, McSIM, equipped with the developed CAD-based geometry processing module

Developing and investigating a pure Monte-Carlo module for transient neutron transport analysis

International Nuclear Information System (INIS)

Mylonakis, Antonios G.; Varvayanni, M.; Grigoriadis, D.G.E.; Catsaros, N.

2017-01-01

Highlights: • Development and investigation of a Monte-Carlo module for transient neutronic analysis. • A transient module developed on the open-source Monte-Carlo static code OpenMC. • Treatment of delayed neutrons is inserted. • Simulation of precursors’ decay process is performed. • Transient analysis of simplified test-cases. - Abstract: In the field of computational reactor physics, Monte-Carlo methodology is extensively used in the analysis of static problems while the transient behavior of the reactor core is mostly analyzed using deterministic algorithms. However, deterministic algorithms make use of various approximations mainly in the geometric and energetic domain that may induce inaccuracy. Therefore, Monte-Carlo methodology which generally does not require significant approximations seems to be an attractive candidate tool for the analysis of transient phenomena. One of the most important constraints towards this direction is the significant computational cost; however since nowadays the available computational resources are continuously increasing, the potential use of the Monte-Carlo methodology in the field of reactor core transient analysis seems feasible. So far, very few attempts to employ Monte-Carlo methodology to transient analysis have been reported. Even more, most of those few attempts make use of several approximations, showing the existence of an “open” research field of great interest. It is obvious that comparing to static Monte-Carlo, a straight-forward physical treatment of a transient problem requires the temporal evolution of the simulated neutrons; but this is not adequate. In order to be able to properly analyze transient reactor core phenomena, the proper simulation of delayed neutrons together with other essential extensions and modifications is necessary. This work is actually the first step towards the development of a tool that could serve as a platform for research and development on this interesting but also

Development of a new lower hybrid antenna module using a poloidal power divider

International Nuclear Information System (INIS)

Maebara, Sunao; Seki, Masami; Suganuma, Kazuaki

1996-07-01

The antenna using poloidal power divider is an effective method for simplification of Lower Hybrid Current Drive (LHCD) antenna system. This method should allow to reduce the power density in the antenna while maintaining a good flexibility of N parallel spectrum of waves. For this purpose, three types of poloidal power divider which split the power in three, and the 3 x 6 multi-junction module were developed. r.f. properties and outgassing of these components were evaluated using the CEA Cadarache RF Test Facility. A good power dividing ratio of 33 ± 4% was obtained for each of these poloidal dividers, and the reflection coefficient was lower value than 1.5%. For the 3 x 6 multi-junction, reflection coefficient was less than 1.3% and r.f. losses lower than 1.0% were measured. On the other hand, it was found in the scattering matrix analysis that reflection coefficient at plasma has to be less than a few % in order to operate these components under available conditions. In combination with two poloidal power dividers connected to the 3 x 6 multi-junction module, quasi stationary operation for r.f. injection time of 1000 sec at 300 kW was demonstrated under water cooling. In this case, it was found that the outgassing rate is in the lower range of 10 -7 Pam 3 s -1 m -2 within the maximum module temperature of ∼100degC. This report describes the experimental and analytical results of a new lower hybrid (LH) antenna module using the poloidal power divider. (author)

Development of Prototype Outcomes-Based Training Modules for Aesthetic Dentistry

Science.gov (United States)

Andres, Maricar Joy T.; Borabo, Milagros L.

2015-01-01

The objective of the study is to know the essential components of Aesthetic Dentistry that will be a basis for prototype Outcomes-based training modules. Using a 5-point Likert scale, the researcher-made questionnaire assessed the different elements of Aesthetic Dentistry which are needed in the designing of the training module, the manner of…

TXESS Revolution: Utilizing TERC's EarthLabs Cryosphere Module to Support Professional Development of Texas Teachers

Science.gov (United States)

Odell, M.; Ellins, K. K.; Polito, E. J.; Castillo Comer, C. A.; Stocks, E.; Manganella, K.; Ledley, T. S.

2010-12-01

TERC’s EarthLabs project provides rigorous and engaging Earth and environmental science labs. Four existing modules illustrate sequences for learning science concepts through data analysis activities and hands-on experiments. A fifth module, developed with NSF, comprises a series of linked inquiry based activities focused on the cryosphere to help students understand concepts around change over time on multiple and embedded time scales. Teachers recruited from the NSF-OEDG-sponsored Texas Earth and Space Science (TXESS) Revolution teacher professional development program conducted a pedagogical review of the Cryosphere EarthLabs module and provided feedback on how well the materials matched high school needs in Texas and were aligned with state and national standards. Five TXESS Revolution teachers field tested the materials in their classrooms and then trained other TXESS Revolution teachers on their implementation during spring and summer 2010. Here we report on the results of PD delivery during the summer 2010 TXESS Revolution summer institute as determined by (1) a set of evaluation instruments that included a pre-post concept map activity to assess changes in workshop teachers’ understanding of the concepts presented, a pre-post test content knowledge test, and a pre-post survey of teachers’ comfort in teaching the Texas Earth and Space Science standards addressed by the module; (2) teacher reflections; and (3) focus group responses. The findings reveal that the teachers liked the module activities and felt they could use them to teach Environmental and Earth Science. They appreciated that the sequence of activities contributed to a deeper understanding and observed that the variety of methods used to present the information accommodates different learning styles. Information about the cryosphere was new to all the teachers. The content knowledge tests reveal that although teachers made appreciable gains, their understanding of cryosphere, how it changes

The Strip Module

DEFF Research Database (Denmark)

Pedersen, Tommy

1996-01-01

When the behaviour of a ship in waves is to be predicted it is convenient to have a tool which includes different approaches to the problem.The aim of this project is to develop such a tool named the strip theory module. The strip theory module will consist of submodules dependent on the I...

Development of high-resolution detector module with depth of interaction identification for positron emission tomography

International Nuclear Information System (INIS)

Niknejad, Tahereh; Pizzichemi, Marco; Stringhini, Gianluca; Auffray, Etiennette; Bugalho, Ricardo; Da Silva, Jose Carlos; Di Francesco, Agostino; Ferramacho, Luis; Lecoq, Paul; Leong, Carlos; Paganoni, Marco; Rolo, Manuel; Silva, Rui; Silveira, Miguel; Tavernier, Stefaan; Varela, Joao; Zorraquino, Carlos

2017-01-01

We have developed a Time-of-flight high resolution and commercially viable detector module for the application in small PET scanners. A new approach to depth of interaction (DOI) encoding with low complexity for a pixelated crystal array using a single side readout and 4-to-1 coupling between scintillators and photodetectors was investigated. In this method the DOI information is estimated using the light sharing technique. The detector module is a 1.53×1.53×15 mm"3 matrix of 8×8 LYSO scintillator with lateral surfaces optically depolished separated by reflective foils. The crystal array is optically coupled to 4×4 silicon photomultipliers (SiPM) array and readout by a high performance front-end ASIC with TDC capability (50 ps time binning). The results show an excellent crystal identification for all the scintillators in the matrix, a timing resolution of 530 ps, an average DOI resolution of 5.17 mm FWHM and an average energy resolution of 18.29% FWHM. - Highlights: • A new method for DOI encoding for PET detectors based on light sharing is proposed. • A prototype module with LYSO scintillator matrix coupled to SiPMs array is produced. • The module has one side readout and 4-to-1 coupling between scintillators and SiPMs. • A compact TOF front-end ASIC is used. • Excellent performances are shown by the prototype module.

Development of high-resolution detector module with depth of interaction identification for positron emission tomography

Energy Technology Data Exchange (ETDEWEB)

Niknejad, Tahereh, E-mail: tniknejad@lip.pt [Laboratory of Instrumentation and Experimental Particles Physics, Lisbon (Portugal); Pizzichemi, Marco [University of Milano-Bicocca (Italy); Stringhini, Gianluca [University of Milano-Bicocca (Italy); CERN, Geneve (Switzerland); Auffray, Etiennette [CERN, Geneve (Switzerland); Bugalho, Ricardo; Da Silva, Jose Carlos; Di Francesco, Agostino [Laboratory of Instrumentation and Experimental Particles Physics, Lisbon (Portugal); Ferramacho, Luis [PETsys Electronics, Oeiras (Portugal); Lecoq, Paul [CERN, Geneve (Switzerland); Leong, Carlos [PETsys Electronics, Oeiras (Portugal); Paganoni, Marco [University of Milano-Bicocca (Italy); Rolo, Manuel [Laboratory of Instrumentation and Experimental Particles Physics, Lisbon (Portugal); INFN, Turin (Italy); Silva, Rui [Laboratory of Instrumentation and Experimental Particles Physics, Lisbon (Portugal); Silveira, Miguel [PETsys Electronics, Oeiras (Portugal); Tavernier, Stefaan [PETsys Electronics, Oeiras (Portugal); Vrije Universiteit Brussel (Belgium); Varela, Joao [Laboratory of Instrumentation and Experimental Particles Physics, Lisbon (Portugal); CERN, Geneve (Switzerland); Zorraquino, Carlos [Biomedical Image Technologies Lab, Universidad Politécnica de Madrid (Spain); CIBER-BBN, Universidad Politécnica de Madrid (Spain)

2017-02-11

We have developed a Time-of-flight high resolution and commercially viable detector module for the application in small PET scanners. A new approach to depth of interaction (DOI) encoding with low complexity for a pixelated crystal array using a single side readout and 4-to-1 coupling between scintillators and photodetectors was investigated. In this method the DOI information is estimated using the light sharing technique. The detector module is a 1.53×1.53×15 mm{sup 3} matrix of 8×8 LYSO scintillator with lateral surfaces optically depolished separated by reflective foils. The crystal array is optically coupled to 4×4 silicon photomultipliers (SiPM) array and readout by a high performance front-end ASIC with TDC capability (50 ps time binning). The results show an excellent crystal identification for all the scintillators in the matrix, a timing resolution of 530 ps, an average DOI resolution of 5.17 mm FWHM and an average energy resolution of 18.29% FWHM. - Highlights: • A new method for DOI encoding for PET detectors based on light sharing is proposed. • A prototype module with LYSO scintillator matrix coupled to SiPMs array is produced. • The module has one side readout and 4-to-1 coupling between scintillators and SiPMs. • A compact TOF front-end ASIC is used. • Excellent performances are shown by the prototype module.

Maternal modulation of paternal effects on offspring development.

Science.gov (United States)

Mashoodh, Rahia; Habrylo, Ireneusz B; Gudsnuk, Kathryn M; Pelle, Geralyn; Champagne, Frances A

2018-03-14

The paternal transmission of environmentally induced phenotypes across generations has been reported to occur following a number of qualitatively different exposures and appear to be driven, at least in part, by epigenetic factors that are inherited via the sperm. However, previous studies of paternal germline transmission have not addressed the role of mothers in the propagation of paternal effects to offspring. We hypothesized that paternal exposure to nutritional restriction would impact male mate quality and subsequent maternal reproductive investment with consequences for the transmission of paternal germline effects. In the current report, using embryo transfer in mice, we demonstrate that sperm factors in adult food restricted males can influence growth rate, hypothalamic gene expression and behaviour in female offspring. However, under natural mating conditions females mated with food restricted males show increased pre- and postnatal care, and phenotypic outcomes observed during embryo transfer conditions are absent or reversed. We demonstrate that these compensatory changes in maternal investment are associated with a reduced mate preference for food restricted males and elevated gene expression within the maternal hypothalamus. Therefore, paternal experience can influence offspring development via germline inheritance, but mothers can serve as a modulating factor in determining the impact of paternal influences on offspring development. © 2018 The Author(s).

Development and Application of High-Content Biological Screening for Modulators of NET Production

Directory of Open Access Journals (Sweden)

Ilaria J. Chicca

2018-03-01

Full Text Available Neutrophil extracellular traps (NETs are DNA-based antimicrobial web-like structures whose release is predominantly mediated by reactive oxygen species (ROS; their purpose is to combat infections. However, unbalanced NET production and clearance is involved in tissue injury, circulation of auto-antibodies and development of several chronic diseases. Currently, there is lack of agreement regarding the high-throughput methods available for NET investigation. This study, therefore, aimed to develop and optimize a high-content analysis (HCA approach, which can be applied for the assay of NET production and for the screening of compounds involved in the modulation of NET release. A suitable paraformaldehyde fixation protocol was established to enable HCA of neutrophils and NETs. Bespoke and in-built bioinformatics algorithms were validated by comparison with standard low-throughput approaches for application in HCA of NETs. Subsequently, the optimized protocol was applied to high-content screening (HCS of a pharmaceutically derived compound library to identify modulators of NETosis. Of 56 compounds assessed, 8 were identified from HCS for further characterization of their effects on NET formation as being either inducers, inhibitors or biphasic modulators. The effects of these compounds on naïve neutrophils were evaluated by using specific assays for the induction of ROS and NET production, while their modulatory activity was validated in phorbol 12-myristate 13-acetate-stimulated neutrophils. Results indicated the involvement of glutathione reductase, Src family kinases, molecular-target-of-Rapamycin, and mitogen-activated-protein-kinase pathways in NET release. The compounds and pathways identified may provide targets for novel therapeutic approaches for treating NET-associated pathologies.

Development of the MCM-D technique for pixel detector modules

International Nuclear Information System (INIS)

Grah, C.

2005-03-01

This thesis treats a copper--polymer based thin film technology, the MCM-D technique and its application when building hybrid pixel detector modules. The ATLAS experiment at the LHC will be equipped with a pixel detector system. The basic mechanical units of the pixel detector are multi chip modules. The main components of these modules are: 16 electronic chips, a controller chip and a large sensor tile, featuring more than 46000 sensor cells. MCM-D is a superior technique to build the necessary signal bus system and the power distribution system directly on the active sensor tile. In collaboration with the Fraunhofer Institute for Reliability and Microintegration, IZM, the thin film process is reviewed and enhanced. The multi layer system was designed and optimized for the interconnection system as well as for the 46000 pixel contacts. Laboratory measurements on prototypes prove that complex routing schemes for geometrically optimized single chips are suitable and have negligible influence on the front--end chips performance. A full scale MCM-D module has been built and it is shown that the technology is suitable to build pixel detector modules. Further tests include the investigation of the impact of hadronic irradiation on the thin film layers. Single chip assemblies have been operated in a test beam environment and the feasibility of the optimization of the sensors could be shown. A review on the potential as well as the perspective for the MCM-D technique in future experiments is given

Development of a wireless nonlinear wave modulation spectroscopy (NWMS) sensor node for fatigue crack detection

Science.gov (United States)

Liu, Peipei; Yang, Suyoung; Lim, Hyung Jin; Park, Hyung Chul; Ko, In Chang; Sohn, Hoon

2014-03-01

Fatigue crack is one of the main culprits for the failure of metallic structures. Recently, it has been shown that nonlinear wave modulation spectroscopy (NWMS) is effective in detecting nonlinear mechanisms produced by fatigue crack. In this study, an active wireless sensor node for fatigue crack detection is developed based on NWMS. Using PZT transducers attached to a target structure, ultrasonic waves at two distinctive frequencies are generated, and their modulation due to fatigue crack formation is detected using another PZT transducer. Furthermore, a reference-free NWMS algorithm is developed so that fatigue crack can be detected without relying on history data of the structure with minimal parameter adjustment by the end users. The algorithm is embedded into FPGA, and the diagnosis is transmitted to a base station using a commercial wireless communication system. The whole design of the sensor node is fulfilled in a low power working strategy. Finally, an experimental verification has been performed using aluminum plate specimens to show the feasibility of the developed active wireless NWMS sensor node.

Stochastic temperature modulation: A new technique in temperature-modulated DSC

International Nuclear Information System (INIS)

Schawe, J.E.K.; Huetter, T.; Heitz, C.; Alig, I.; Lellinger, D.

2006-01-01

A new temperature-modulated differential scanning calorimetry (TMDSC) technique is introduced. The technique is based on stochastic temperature modulation and has been developed as a consequence of a generalized theory of a temperature-modulated DSC. The quasi-static heat capacity and the frequency-dependent complex heat capacity can be determined over a wide frequency range in one single measurement without further calibration. Furthermore, the reversing and non-reversing heat flows are determined directly from the measured data. Examples show the frequency dependence of the glass transition, the isothermal curing of thermosets and a solid-solid transition

Development of a lower extremity wearable exoskeleton with double compact elastic module: preliminary experiments

Directory of Open Access Journals (Sweden)

Y. Long

2017-08-01

Full Text Available In this paper, a double compact elastic module is designed and implemented in the lower extremity exoskeleton. The double compact elastic module is composed of two parts, i.e., physical human robot interaction (pHRI measurement and the elastic actuation system (EAS, which are called proximal elastic module (PEM and distal elastic module (DEM respectively. The PEM is used as the pHRI information collection device while the DEM is used as the compliance device. A novel compact parallelogram-like structure based torsional spring is designed and developed. An iterative finite element analysis (FEA based optimization process was conducted to find the optimal parameters in the search space. In the PEM, the designed torsional spring has an outer circle with a diameter of 60 mm and an inner hole with a diameter of 12 mm, while in the DEM, the torsional spring has the outer circle with a diameter of 80 mm and the inner circle with a diameter of 16 mm. The torsional spring in the PEM has a thickness of 5 mm and a weight of 60 g, while that in the DEM has a thickness of 10 mm and a weight of 80 g. The double compact elastic module prototype is embedded in the mechanical joint directly. Calibration experiments were conducted on those two elastic modules to obtain the linear torque versus angle characteristic. The calibration experimental results show that this torsional spring in the PEM has a stiffness of 60.2 Nm rad−1, which is capable of withstanding a maximum torque of 4 Nm, while that in the DEM has a stiffness of 80.2 Nm rad−1, which is capable of withstanding a maximum torque of 30 Nm. The experimental results and the simulation data show that the maximum resultant errors are 6 % for the PEM and 4 % for the DEM respectively. In this paper, an assumed regression algorithm is used to learn the human motion intent (HMI based on the pHRI collection. The HMI is defined as the angular position of the human limb joint. A

Radiation effect characterization and test methods of single-chip and multi-chip stacked 16Mbit DRAMs

International Nuclear Information System (INIS)

LaBel, K.A.; Gates, M.M.; Moran, A.K.; Kim, H.S.; Seidleck, C.M.; Marshall, P.; Kinnison, J.; Carkhuff, B.

1996-01-01

This paper presents radiation effects characterization performed by the NASA Goddard Space Flight Center (GSFC) on spaceflight candidate 16Mbit DRAMs. This includes heavy ion, proton, and Co60 irradiations on single-chip devices as well as proton irradiation of a stacked DRAM module. Lastly, a discussion of test methodology is undertaken

Development of a control system for a heavy object handling manipulator. Application to a remote maintenance system for ITER blanket module

International Nuclear Information System (INIS)

Yoshimi, Takashi; Tsuji, Kouichi; Miyagawa, Shinichi; Kubo, Tomomi; Kakudate, Satoshi; Tada, Eisuke

2001-01-01

This paper describes a control system for the heavy object handling manipulator. It has been developed for the blanket module remote maintenance system of ITER (International Thermonuclear Fusion Experimental Reactor). A rail-mounted vehicle-type manipulator is proposed for the precise handling of a blanket module which is about 4 tons in weight. Basically, this manipulator is controlled by teaching-playback technique. When grasping or releasing the module, the manipulator sags and the position of the end-effector changes about 50 [mm]. Applying only the usual teaching-playback control makes the smooth operation of setting/removing modules to/from the vacuum vessel wall difficult due to this position change. To solve this proper problem of heavy object handling manipulator, we have developed a system which uses motion patterns generated from two kinds of teaching points. These motion patterns for setting/removing heavy objects are generated by combining teaching points for positioning the manipulator with and without grasping the object. When these motion patterns are applied, the manipulator can transfer the object's weight smoothly at the setting/removing point. This developed system has been applied to the real-scale mock-up of the vehicle manipulator and through the actual module setting/removing experiments, we have verified its effectiveness and realized smooth maintenance operation. (author)

Module-Integrated Power Converters Based on Universal Dock

Energy Technology Data Exchange (ETDEWEB)

Chapman, Patrick; Rodriguez, Fernando

2015-03-13

Solar power installations using alternating current photovoltaic (ACPV) modules have significant cost and performance advantages over systems using conventional solar modules and string inverters. ACPV modules have improved energy harvest due to module-level power point tracking and redundancy. More importantly, ACPV modules are easier and cheaper to install, lowering the total installed cost, indirect costs, and barriers to market entry. Furthermore, ACPV modules have communications and data logging capability, yielding module-level telemetry data that is useful in site diagnostics and other data applications. The products of these efforts were threefold. First, an advanced microinverter power topology was developed, modeled, simulated, and tested. Second, new microinverter enclosure concepts were developed and tested. Third, a new ACPV module prototype was constructed, combining the power topology and the enclosure concepts. SolarBridge filed for patents in each of these areas and is transitioning the project from a concept phase to full development.

The European DISABKIDS project: development of seven condition-specific modules to measure health related quality of life in children and adolescents

Directory of Open Access Journals (Sweden)

Bullinger Monika

2005-11-01

Full Text Available Abstract Background The European DISABKIDS project aims to enhance the Health Related Quality of Life (HRQoL of children and adolescents with chronic medical conditions and their families. We describe the development of the seven cross-nationally tested condition-specific modules of the European DISABKIDS HRQoL instrument in a population of children and adolescents. The condition-specific modules are intended for use in conjunction with the DISABKIDS chronic generic module. Methods Focus groups were used to construct the pilot version of the DISABKIDS condition-specific HRQoL modules for asthma, juvenile idiopathic arthritis, atopic dermatitis, cerebral palsy, cystic fibrosis, diabetes and epilepsy. Analyses were conducted on pilot test data in order to construct field test versions of the modules. A series of factor analyses were run, first, to determine potential structures for each condition-specific module, and, secondly, to select a reduced number of items from the pilot test to be included in the field test. Post-field test analyses were conducted to retest the domain structure for the final DISABKIDS condition-specific modules. Results The DISABKIDS condition-specific modules were tested in a pilot study of 360 respondents, and subsequently in a field test of 1152 respondents in 7 European countries. The final condition-specific modules consist of an 'Impact' domain and an additional domain (e.g. worry, stigma, treatment with between 10 to 12 items in total. The Cronbach's alpha of the final domains was found to vary from 0.71 to 0.90. Conclusion The condition-specific modules of the DISABKIDS instrument were developed through a step-by-step process including cognitive interview, clinical expertise, factor analysis, correlations and internal consistency. A cross-national pilot and field test were necessary to collect these data. In general, the internal consistency of the domains was satisfactory to high. In future, the DISABKIDS

GREET Pretreatment Module

Energy Technology Data Exchange (ETDEWEB)

Adom, Felix K. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Dunn, Jennifer B. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Han, Jeongwoo [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division

2014-09-01

A wide range of biofuels and biochemicals can be produced from cellulosic biomass via different pretreatment technologies that yield sugars. Process simulations of dilute acid and ammonia fiber expansion pretreatment processes and subsequent hydrolysis were developed in Aspen Plus for four lignocellulosic feedstocks (corn stover, miscanthus, switchgrass, and poplar). This processing yields sugars that can be subsequently converted to biofuels or biochemical. Material and energy consumption data from Aspen Plus were then compiled in a new Greenhouses Gases, Regulated Emissions, and Energy Use in Transportation (GREET^TM) pretreatment module. The module estimates the cradle-to-gate fossil energy consumption (FEC) and greenhouse gas (GHG) emissions associated with producing fermentable sugars. This report documents the data and methodology used to develop this module and the cradle-to-gate FEC and GHG emissions that result from producing fermentable sugars.

FASTBUS Snoop Diagnostic Module

International Nuclear Information System (INIS)

Walz, H.V.; Downing, R.

1980-11-01

Development of the FASTBUS Snoop Module, undertaken as part of the prototype program for the new interlaboratory data bus standard, is described. The Snoop Module resides on a FASTBUS crate segment and provides diagnostic monitoring and testing capability. Communication with a remote host computer is handled independent of FASTBUS through a serial link. The module consists of a high-speed ECL front-end to monitor and single-step FASTBUS cycles, a master-slave interface, and a control microprocessor with serial communication ports. Design details and performance specifications of the prototype module are reported. 9 figures, 1 table

Model theory and modules

CERN Document Server

Prest, M

1988-01-01

In recent years the interplay between model theory and other branches of mathematics has led to many deep and intriguing results. In this, the first book on the topic, the theme is the interplay between model theory and the theory of modules. The book is intended to be a self-contained introduction to the subject and introduces the requisite model theory and module theory as it is needed. Dr Prest develops the basic ideas concerning what can be said about modules using the information which may be expressed in a first-order language. Later chapters discuss stability-theoretic aspects of module

Modulation of Rhamm (CD168) for selective adipose tissue development

Science.gov (United States)

Turley, Eva A; Bissell, Mina J

2014-05-06

Herein is described the methods and compositions for modulation of Rhamm, also known as CD 186, and its effects on wound repair, muscle differentiation, bone density and adipogeneisis through its ability to regulate mesenchymal stem cell differentiation. Compositions and methods are provided for blocking Rhamm function for selectively increasing subcutaneous, but not, visceral fat. Compositions and methods for modulating Rhamm in wound repair are also described.

Process development for automated solar cell and module production. Task 4. Automated array assembly. Quarterly report No. 1

Energy Technology Data Exchange (ETDEWEB)

Hagerty, J. J.

1980-10-15

Work has been divided into five phases. The first phase is to modify existing hardware and controlling computer software to: (1) improve cell-to-cell placement accuracy, (2) improve the solder joint while reducing the amount of solder and flux smear on the cell's surface, and (3) reduce the system cycle time to 10 seconds. The second phase involves expanding the existing system's capabilities to be able to reject broken cells and make post-solder electrical tests. Phase 3 involves developing new hardware to allow for the automated encapsulation of solar modules. This involves three discrete pieces of hardware: (1) a vacuum platen end effector for the robot which allows it to pick up the 1' x 4' array of 35 inter-connected cells. With this, it can also pick up the cover glass and completed module, (2) a lamination preparation station which cuts the various encapsulation components from roll storage and positions them for encapsulation, and (3) an automated encapsulation chamber which interfaces with the above two and applies the heat and vacuum to cure the encapsulants. Phase 4 involves the final assembly of the encapsulated array into a framed, edge-sealed module completed for installation. For this we are using MBA's Glass Reinforced Concrete (GRC) in panels such as those developed by MBA for JPL under contract No. 955281. The GRC panel plays the multiple role of edge frame, substrate and mounting structure. An automated method of applying the edge seal will also be developed. The final phase (5) is the fabrication of six 1' x 4' electrically active solar modules using the above developed equipment. Progress is reported. (WHK)

ANTICIPATORY GUIDANCE MODULE CHANGES THE AUTHORITARITATIVE PARENTING OF PARENTS IN STIMULATING CHILDREN DEVELOPMENT

Directory of Open Access Journals (Sweden)

M. Hasinuddin

2017-04-01

Full Text Available Introduction: Anticipatory guidance is a method used by nurses to help parents provide the development of behavior change towards a better understanding of their children. The purpose of this study was to analyze the provision modul of anticipatory guidance to parents and their effects on patterns of authoritarian parenting in stimulating development in kindergarten Dharmawanita Bangkalan Regency. Method: The design in this study was experimental pre post test with control group. The population was the parents of students in Dharmawanita Bangkalan kindergarten in 2010. Respondents were 15 people in the treatment group and 15 people in control group who meet the inclusion criteria. Data collected by using a questionnaire. Data then analyzed using Wilcoxon and Mann Whitney test. Result: The result showed that the differences in upbringing the parents before and after the anticipatory guidance given p value of 0.001, whereas in the control group there was no difference with a p value of 0.083. To find out the difference of counselling terms between treatment and control groups were performed by mann whitney test with p-value (0,004 < α (0.05. Discussion: Based on these results we can conclude that modul of anticipatory guidance has an impact on the upbringing of parents in stimulating growth in children in kindergarten Dharmawanita Bangkalan. Research on the effect of anticipatory guidance by the nurse to child development is necessary as a follow up of this research by considering the factors that in fl uence the development of the child itself.

Development and pilot testing of full-scale membrane distillation modules for deployment of waste heat

NARCIS (Netherlands)

Jansen, A.E.; Assink, J.W.; Hanemaaijer, J.H.; Medevoort, J. van; Sonsbeek, E. van

2013-01-01

Membrane distillation is an attractive technology for extracting fresh water from seawater. Newly developed modules have been used in pilot tests and bench scale tests to demonstrate the potential of producing excellent product water quality in a single step, little need for water pretreatment and a

A Module Experimental Process System Development Unit (MEPSDU). [flat plate solar arrays

Science.gov (United States)

1981-01-01

The development of a cost effective process sequence that has the potential for the production of flat plate photovoltaic modules which meet the price goal in 1986 of 70 cents or less per Watt peak is described. The major accomplishments include (1) an improved AR coating technique; (2) the use of sand blast back clean-up to reduce clean up costs and to allow much of the Al paste to serve as a back conductor; and (3) the development of wave soldering for use with solar cells. Cells were processed to evaluate different process steps, a cell and minimodule test plan was prepared and data were collected for preliminary Samics cost analysis.

Deep sub-micron FD-SOI for front-end application

International Nuclear Information System (INIS)

Ikeda, H.; Arai, Y.; Hara, K.; Hayakawa, H.; Hirose, K.; Ikegami, Y.; Ishino, H.; Kasaba, Y.; Kawasaki, T.; Kohriki, T.; Martin, E.; Miyake, H.; Mochizuki, A.; Tajima, H.; Tajima, O.; Takahashi, T.; Takashima, T.; Terada, S.; Tomita, H.; Tsuboyama, T.

2007-01-01

In order to confirm benefits of a deep sub-micron FD-SOI and to identify possible issues concerning front-end circuits with the FD-SOI, we have submitted a small design to Oki Electric Industry Co., Ltd. via the multi-chip project service of VDEC, the University of Tokyo. The initial test results and future plans for development are presented

Development of Power Supply Management Module for Radio Signal Repeaters of Automatic Metering Reading System in Variable Solar Density Conditions

Directory of Open Access Journals (Sweden)

Kondratjevs K.

2016-02-01

Full Text Available In recent years, there has been significant research focus that revolves around harvesting and minimising energy consumption by wireless sensor network nodes. When a sensor node is depleted of energy, it becomes unresponsive and disconnected from the network that can significantly influence the performance of the whole network. The purpose of the present research is to create a power supply management module in order to provide stable operating voltage for autonomous operations of radio signal repeaters, sensors or gateways of WSN. The developed management module is composed of a solar panel, lithium battery and power supply management module. The novelty of the research is the management module, which ensures stable and uninterrupted operations of electronic equipment in various power supply modes in different situations, simultaneously ensuring energy protection and sustainability of the module components. The management module is able to provide power supply of 5 V for electronics scheme independently, without power interruption switching between power sources and power flows in different directions.

Development of Power Supply Management Module for Radio Signal Repeaters of Automatic Metering Reading System in Variable Solar Density Conditions

Science.gov (United States)

Kondratjevs, K.; Zabasta, A.; Selmanovs-Pless, V.

2016-02-01

In recent years, there has been significant research focus that revolves around harvesting and minimising energy consumption by wireless sensor network nodes. When a sensor node is depleted of energy, it becomes unresponsive and disconnected from the network that can significantly influence the performance of the whole network. The purpose of the present research is to create a power supply management module in order to provide stable operating voltage for autonomous operations of radio signal repeaters, sensors or gateways of WSN. The developed management module is composed of a solar panel, lithium battery and power supply management module. The novelty of the research is the management module, which ensures stable and uninterrupted operations of electronic equipment in various power supply modes in different situations, simultaneously ensuring energy protection and sustainability of the module components. The management module is able to provide power supply of 5 V for electronics scheme independently, without power interruption switching between power sources and power flows in different directions.

The Status of Thermophotovoltaic Energy Conversion Technology at Lockheed Martin Corporation

Energy Technology Data Exchange (ETDEWEB)

EJ Brown; PF Baldasaro; SR Burger; LR Danielson; DM DePoy; JM Dolatowski; PM Fourspring; GJ Nichols; WF Topper; TD Rahmlow

2004-07-29

In a thermophotovoltaic (TPV) energy conversion system, a heated surface radiates in the mid-infrared range onto photocells which are sensitive at these energies. Part of the absorbed energy is converted into electric output. Conversion efficiency is maximized by reducing the absorption of non-convertible energy with some form of spectral control. In a TPV system, many technology options exist. Our development efforts have concentrated on flat-plate geometries with greybody radiators, front surface tandem filters and a multi-chip module (MCM) approach that allows selective fabrication processes to match cell performance. Recently, we discontinued development of GaInAsSb quaternary cell semiconductor material in favor of ternary GaInAs material. In our last publication (Ref. 1), the authors reported conversion efficiencies of about 20% (radiator 950 C, cells 22 C) for small modules (1-4 cm{sup 2}) tested in a prototypic cavity test environment. Recently, we have achieved measured conversion efficiencies of about 12.5% in larger ({approx}100 cm{sup 2}) test arrays. The efficiency reduction in the larger arrays was probably due to quality and variation of the cells as well as non-uniform illumination from the hot radiator to the cold plate. Modules in these tests used GaInAsSb cells with 0.52 eV bandgap and front surface filters for spectral control. This paper provides details of the individual system components and the rationale for our technical decisions. It also describes the measurement techniques used to record these efficiencies.

WE-AB-204-11: Development of a Nuclear Medicine Dosimetry Module for the GPU-Based Monte Carlo Code ARCHER

Energy Technology Data Exchange (ETDEWEB)

Liu, T; Lin, H; Xu, X [Rensselaer Polytechnic Institute, Troy, NY (United States); Stabin, M [Vanderbilt Univ Medical Ctr, Nashville, TN (United States)

2015-06-15

Purpose: To develop a nuclear medicine dosimetry module for the GPU-based Monte Carlo code ARCHER. Methods: We have developed a nuclear medicine dosimetry module for the fast Monte Carlo code ARCHER. The coupled electron-photon Monte Carlo transport kernel included in ARCHER is built upon the Dose Planning Method code (DPM). The developed module manages the radioactive decay simulation by consecutively tracking several types of radiation on a per disintegration basis using the statistical sampling method. Optimization techniques such as persistent threads and prefetching are studied and implemented. The developed module is verified against the VIDA code, which is based on Geant4 toolkit and has previously been verified against OLINDA/EXM. A voxelized geometry is used in the preliminary test: a sphere made of ICRP soft tissue is surrounded by a box filled with water. Uniform activity distribution of I-131 is assumed in the sphere. Results: The self-absorption dose factors (mGy/MBqs) of the sphere with varying diameters are calculated by ARCHER and VIDA respectively. ARCHER’s result is in agreement with VIDA’s that are obtained from a previous publication. VIDA takes hours of CPU time to finish the computation, while it takes ARCHER 4.31 seconds for the 12.4-cm uniform activity sphere case. For a fairer CPU-GPU comparison, more effort will be made to eliminate the algorithmic differences. Conclusion: The coupled electron-photon Monte Carlo code ARCHER has been extended to radioactive decay simulation for nuclear medicine dosimetry. The developed code exhibits good performance in our preliminary test. The GPU-based Monte Carlo code is developed with grant support from the National Institute of Biomedical Imaging and Bioengineering through an R01 grant (R01EB015478)

Modeling Tolerance Development for the Effect on Heart Rate of the Selective S1P1 Receptor Modulator Ponesimod.

Science.gov (United States)

Lott, Dominik; Lehr, Thorsten; Dingemanse, Jasper; Krause, Andreas

2017-09-15

Ponesimod is a selective sphingosine-1-phosphate-1 (S1P 1 ) receptor modulator currently under investigation for the treatment of multiple sclerosis. S1P receptor modulators reduce heart rate following treatment initiation. This effect disappears with repeated dosing, enabling development of innovative uptitration regimens to optimize patient safety. There are currently no published pharmacokinetic/pharmacodynamic models describing the heart rate reduction of S1P receptor modulators in humans. The model developed here provides quantification of this effect for ponesimod. A direct-effect I max model with estimated maximum reduction of 45%, tolerance development, and circadian variation best described this effect. The pooled data from nine clinical studies enabled characterization of interindividual variability. The model was used to simulate different treatment regimens to compare the effect of high initial doses vs. gradual uptitration with respect to the occurrence of bradycardia. The results indicate a better safety profile when using gradual uptitration. The model allows studying dosing regimens not clinically tested in silico. © 2017 American Society for Clinical Pharmacology and Therapeutics.

Evolutionary and developmental modules.

Science.gov (United States)

Lacquaniti, Francesco; Ivanenko, Yuri P; d'Avella, Andrea; Zelik, Karl E; Zago, Myrka

2013-01-01

The identification of biological modules at the systems level often follows top-down decomposition of a task goal, or bottom-up decomposition of multidimensional data arrays into basic elements or patterns representing shared features. These approaches traditionally have been applied to mature, fully developed systems. Here we review some results from two other perspectives on modularity, namely the developmental and evolutionary perspective. There is growing evidence that modular units of development were highly preserved and recombined during evolution. We first consider a few examples of modules well identifiable from morphology. Next we consider the more difficult issue of identifying functional developmental modules. We dwell especially on modular control of locomotion to argue that the building blocks used to construct different locomotor behaviors are similar across several animal species, presumably related to ancestral neural networks of command. A recurrent theme from comparative studies is that the developmental addition of new premotor modules underlies the postnatal acquisition and refinement of several different motor behaviors in vertebrates.

Development and evaluation of a time-dependent radiographic technology by using a muon read out module

Science.gov (United States)

Kusagaya, T.; Uchida, T.; Tanaka, H. K. M.; Tanaka, M.

2012-04-01

We will present a real-time monitoring system for cosmic-ray muon radiography as an application of a readout module developed by T. Uchida et al [1,2]. The readout module was developed originally for probing the internal structure of volcanoes in 2008 [3]. Its features are small in size, low power consumption, and the capability to access remotely via Ethernet. The current statistics data of cosmic-ray muons can be read from a PC placed far from the module at anytime. By using this feature, we constructed a real-time monitoring system. As a test experiment, we observed fluid movement in a cylinder with a diameter of 112 meters water equivalent. In this work, we succeeded to resolve the fluid movement in the cylinder. We varied the fluid level inside the cylinder and measured the muon intensity. We found that the muon intensity correlates inversely with the fluid level: the muon intensity increases for the lower fluid level and decreases for the higher fluid level. Although the time resolution of muon radiography was sufficient to resolve changes in the fluid level, an adequate time window has to be chosen for different operating conditions. We anticipate that this system will be applicable to exploring high-speed phenomena in a gigantic object.

Development of a multi-channel front-end electronics module based on ASIC for silicon strip array detectors

International Nuclear Information System (INIS)

Zhao Xingwen; Yan Duo; Su Hong; Qian Yi; Kong Jie; Zhang Xueheng; Li Zhankui; Li Haixia

2014-01-01

The silicon strip array detector is one of external target facility subsystems in the Cooling Storage Ring on the Heavy Ion Research Facility at Lanzhou (HIRFL-CSR). Using the ASICs, the front-end electronics module has been developed for the silicon strip array detectors and can implement measurement of energy of 96 channels. The performance of the front-end electronics module has been tested. The energy linearity of the front-end electronics module is better than 0.3% for the dynamic range of 0.1∼0.7 V. The energy resolution is better than 0.45%. The maximum channel crosstalk is better than 10%. The channel consistency is better than 1.3%. After continuously working for 24 h at room temperature, the maximum drift of the zero-peak is 1.48 mV. (authors)

Requirements for a Dynamic Solvent Extraction Module to Support Development of Advanced Technologies for the Recycle of Used Nuclear Fuel

International Nuclear Information System (INIS)

Law, Jack; Rutledge, Veronica; Pereira, Candido; Copple, Jackie; Frey, Kurt; Krebs, John; Maggos, Laura; Nichols, Kevin; Wardle, Kent; Sadasivan, Pratap; DeAlmieda, Valmor; Depaoli, David

2011-01-01

The Department of Energy's Nuclear Energy Advanced Modeling and Simulation (NEAMS) Program has been established to create and deploy next generation, verified and validated nuclear energy modeling and simulation capabilities for the design, implementation, and operation of future nuclear energy systems to improve the U.S. energy security. As part of the NEAMS program, Integrated Performance and Safety Codes (IPSC's) are being produced to significantly advance the status of modeling and simulation of energy systems beyond what is currently available to the extent that the new codes be readily functional in the short term and extensible in the longer term. The four IPSC areas include Safeguards and Separations, Reactors, Fuels, and Waste Forms. As part of the Safeguards and Separations (SafeSeps) IPSC effort, interoperable process models are being developed that enable dynamic simulation of an advanced separations plant. A SafeSepss IPSC 'toolkit' is in development to enable the integration of separation process modules and safeguards tools into the design process by providing an environment to compose, verify and validate a simulation application to be used for analysis of various plant configurations and operating conditions. The modules of this toolkit will be implemented on a modern, expandable architecture with the flexibility to explore and evaluate a wide range of process options while preserving their stand-alone usability. Modules implemented at the plant-level will initially incorporate relatively simple representations for each process through a reduced modeling approach. Final versions will incorporate the capability to bridge to subscale models to provide required fidelity in chemical and physical processes. A dynamic solvent extraction model and its module implementation are needed to support the development of this integrated plant model. As a stand-alone application, it will also support solvent development of extraction flowsheets and integrated

Development of a Study Module on and Pedagogical Approaches to Industrial Environmental Engineering and Sustainability in Mozambique

Science.gov (United States)

Husgafvel, Roope; Martikka, Mikko; Egas, Andrade; Ribiero, Natasha; Dahl, Olli

2017-01-01

Addressing the sustainability challenges in the forest sector in Mozambique requires capacity building for higher education and training of new skilled expert and future decision-makers. Our approach was to develop a study module on and pedagogical approaches to industrial environmental engineering and sustainability. The idea was to develop a…

Responding empathically to patients: Development, implementation, and evaluation of a communication skills training module for oncology nurses.

Science.gov (United States)

Pehrson, Cassandra; Banerjee, Smita C; Manna, Ruth; Shen, Megan Johnson; Hammonds, Stacey; Coyle, Nessa; Krueger, Carol A; Maloney, Erin; Zaider, Talia; Bylund, Carma L

2016-04-01

The purpose of this paper is to report on the development, implementation, and evaluation of a Communication Skills Training (CST) module for inpatient oncology nurses on how to respond empathically to patients. 248 nurses from a USA cancer center participated in a CST module on responding empathically to patients. Nurses completed pre- and post-training Standardized Patient Assessments (SPAs), a survey on their confidence in and intent to utilize skills taught, and a six-month post-training survey of self-reported use of skills. Results indicate that nurses were satisfied with the module, reporting that agreement or strong agreement to 5 out of 6 items assessing satisfaction 96.7%-98.0% of the time. Nurses' self-efficacy in responding empathically significantly increased pre- to post-training. Additionally, nurses showed empathy skill improvement in the post-SPAs. Finally, 88.2% of nurses reported feeling confident in using the skills they learned post-training and reported an increase of 42-63% in the use of specific empathic skills. A CST module for nurses in responding empathically to patients showed feasibility, acceptability, and improvement in self-efficacy as well as skill uptake. This CST module provides an easily targeted intervention for improving nurse-patient communication and patient-centered care. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Module theory, extending modules and generalizations

CERN Document Server

Tercan, Adnan

2016-01-01

The main focus of this monograph is to offer a comprehensive presentation of known and new results on various generalizations of CS-modules and CS-rings. Extending (or CS) modules are generalizations of injective (and also semisimple or uniform) modules. While the theory of CS-modules is well documented in monographs and textbooks, results on generalized forms of the CS property as well as dual notions are far less present in the literature. With their work the authors provide a solid background to module theory, accessible to anyone familiar with basic abstract algebra. The focus of the book is on direct sums of CS-modules and classes of modules related to CS-modules, such as relative (injective) ejective modules, (quasi) continuous modules, and lifting modules. In particular, matrix CS-rings are studied and clear proofs of fundamental decomposition results on CS-modules over commutative domains are given, thus complementing existing monographs in this area. Open problems round out the work and establish the...

Toward the development of a low-cost laser Doppler module for ophthalmic microscopes

Science.gov (United States)

Cattini, Stefano; Rovati, Luigi

2012-03-01

A laser Doppler module easily integrated into a commercial ophthalmic microscope is proposed. Such setup adds flow measurement capability to standard visual inspection of the fundus. The proposed instrument may provide important clinical information such as the detection of vessel occlusion provided by surgical treatments (i.e. photocoagulation). The measuring system is based on a self-mixing laser diode Doppler flowmeter (SM-DF). Reduced costs, easy implementation and small size represent the main features of SM-DF. Moreover, this technique offers the advantage to have the excitation and measurement beams spatially overlapped, thus both overcoming the alignment difficulty of traditional laser Doppler flowmeter and, well fitting with to limited optical aperture of the pupil. Thanks to an on-board DSP-microcontroller, the optoelectronic module directly estimates the blood flow; USB connection and an ad-hoc developed user-friendly software interface allow displaying the result on a personal computer. Preliminary test demonstrates the applicability of the proposed measuring system.

Development of 8 MW Power Supply Based on Pulse Step Modulation Technique for Auxiliary Heating System on HL-2A

International Nuclear Information System (INIS)

Xu Weidong; Xuan Weimin; Yao Lieying; Wang Yingqiao

2012-01-01

The high voltage power supply (HVPS) based on pulse step modulation (PSM) has already been developed for the auxiliary heating system on HL-2A. This power supply consists of many switch power supplies, and its output voltage can be obtained by modulating their delay time and pulse widths. The PSM topology and control principle are presented in this paper. The simple algorithms for the control system are explained clearly. The switch power supply (SPS) module has been built and the test results show it can meet the requirements of the auxiliary heating system. Now, 112 SPS modules and the whole system have already been developed. Its maximum output is about 72 kV/93 A. The protection time is less than 5 μs. The different outputs of this power supply are used for the electron cyclotron resonant heating (ECRH) system with different duty ratios. The experimental results of the entire system are presented. The results indicate that the whole system can meet the requirements of the auxiliary heating system on HL-2A.

Development of Mole Concept Module Based on Structured Inquiry with Interconection of Macro, Submicro, and Symbolic Representation for Grade X of Senior High School

Science.gov (United States)

Sagita, R.; Azra, F.; Azhar, M.

2018-04-01

The research has created the module of mole concept based on structured inquiry with interconection of macro, submicro, and symbolic representation and determined the validity and practicality of the module. The research type was Research and Development (R&D). The development model was 4-D models that consist of four steps: define, design, develop, and disseminate. The research was limited on develop step. The instrument of the research was questionnaire form that consist of validity and practicality sheets. The module was validated by 5 validators. Practicality module was tested by 2 chemistry teachers and 28 students of grade XI MIA 5 at SMAN 4 of Padang. Validity and practicality data were analysed by using the kappa Cohen formula. The moment kappa average of 5 validators was 0,95 with highest validity category. The moment kappa average of teachers and students were 0,89 and 0,91 praticality with high category. The result of the research showed that the module of mole concept based on structured inquiry with interconection of macro, submicro, and symbolic representation was valid and practice to be used on the learning chemistry.

Dry-film polymer waveguide for silicon photonics chip packaging.

Science.gov (United States)

Hsu, Hsiang-Han; Nakagawa, Shigeru

2014-09-22

Polymer waveguide made by dry film process is demonstrated for silicon photonics chip packaging. With 8 μm × 11.5 μm core waveguide, little penalty is observed up to 25 Gbps before or after the light propagate through a 10-km long single-mode fiber (SMF). Coupling loss to SMF is 0.24 dB and 1.31 dB at the polymer waveguide input and output ends, respectively. Alignment tolerance for 0.5 dB loss increase is +/- 1.0 μm along both vertical and horizontal directions for the coupling from the polymer waveguide to SMF. The dry-film polymer waveguide demonstrates promising performance for silicon photonics chip packaging used in next generation optical multi-chip module.

Development of New Low-Cost, High-Performance, PV Module Encapsulant/Packaging Materials: Final Technical Progress Report, 22 October 2002 - 15 November 2007

Energy Technology Data Exchange (ETDEWEB)

Tucker, R.

2008-04-01

Report on objectives to work with U.S.-based PV module manufacturers (c-Si, a-Si, CIS, other thin films) to develop/qualify new low-cost, high-performance PV module encapsulant/packaging materials, and processes using the packaging materials.

Pre-attentive and attentive vision module

NARCIS (Netherlands)

Nyamsuren, Enkhbold; Taatgen, Niels A.

This paper introduces a new vision module, called PAAV, developed for the cognitive architecture ACT-R. Unlike ACT-R's default vision module that was originally developed for top-down perception only, PAAV was designed to model a wide range of tasks, such as visual search and scene viewing, where

Development of active edge pixel sensors and four-side buttable modules using vertical integration technologies

CERN Document Server

INSPIRE-00219560; Moser, H.-G.; Nisius, R.; Richter, R.H.; Terzo, S.; Weigell, P.

2014-01-01

We present an R&D activity focused on the development of novel modules for the upgrade of the ATLAS pixel system at the High Luminosity LHC (HL-LHC). The modules consist of n-in-p pixel sensors, 100 or 200 $\\mu$m thick, produced at VTT (Finland) with an active edge technology, which considerably reduces the dead area at the periphery of the device. The sensors are interconnected with solder bump-bonding to the ATLAS FE-I3 and FE-I4 read-out chips, and characterized with radioactive sources and beam tests at the CERN-SPS and DESY. The results of these measurements will be discussed for devices before and after irradiation up to a fluence of $5\\times 10^{15}$ \

SU-F-T-184: 3D Range-Modulator for Scanned Particle Therapy: Development, Monte Carlo Simulations and Measurements

Energy Technology Data Exchange (ETDEWEB)

Simeonov, Y; Penchev, P; Ringbaek, T Printz [University of Applied Sciences, Institute of Medical Physics and Radiation Protection, Giessen (Germany); Brons, S [Heidelberg Ion-Beam Therapy Center (HIT), Heidelberg (Germany); Weber, U [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, Darmstadt (Germany); Zink, K [University of Applied Sciences, Institute of Medical Physics and Radiation Protection, Giessen (Germany); University Hospital Giessen-Marburg, Marburg (Germany)

2016-06-15

Purpose: Active raster scanning in particle therapy results in highly conformal dose distributions. Treatment time, however, is relatively high due to the large number of different iso-energy layers used. By using only one energy and the so called 3D range-modulator irradiation times of a few seconds only can be achieved, thus making delivery of homogeneous dose to moving targets (e.g. lung cancer) more reliable. Methods: A 3D range-modulator consisting of many pins with base area of 2.25 mm2 and different lengths was developed and manufactured with rapid prototyping technique. The form of the 3D range-modulator was optimised for a spherical target volume with 5 cm diameter placed at 25 cm in a water phantom. Monte Carlo simulations using the FLUKA package were carried out to evaluate the modulating effect of the 3D range-modulator and simulate the resulting dose distribution. The fine and complicated contour form of the 3D range-modulator was taken into account by a specially programmed user routine. Additionally FLUKA was extended with the capability of intensity modulated scanning. To verify the simulation results dose measurements were carried out at the Heidelberg Ion Therapy Center (HIT) with a 400.41 MeV 12C beam. Results: The high resolution measurements show that the 3D range-modulator is capable of producing homogeneous 3D conformal dose distributions, simultaneously reducing significantly irradiation time. Measured dose is in very good agreement with the previously conducted FLUKA simulations, where slight differences were traced back to minor manufacturing deviations from the perfect optimised form. Conclusion: Combined with the advantages of very short treatment time the 3D range-modulator could be an alternative to treat small to medium sized tumours (e.g. lung metastasis) with the same conformity as full raster-scanning treatment. Further simulations and measurements of more complex cases will be conducted to investigate the full potential of the 3D

The research and development of module 3D designing system for nuclear power project based on the PDMS

International Nuclear Information System (INIS)

Lu Qinwu; Li Yi; Wu Xiangyong

2012-01-01

In order to meet the demand of implementing Modularization design in CPR1000 nuclear power projects, this study aims to develop, relying on CPR1000 nuclear power project, the self-reliant module 3D design system based on the PDMS. so as to offer a convenient and effective module 3D design tool for the designers. Satisfactory results have been achieved through the test and application of two design projects. The research and application have entered the domestic advanced level. (authors)

Development of the MCM-D technique for pixel detector modules

CERN Document Server

Grah, Christian

2005-01-01

This thesis treats a copper--polymer based thin film technology, the MCM-D technique and its application when building hybrid pixel detector modules. The ATLAS experiment at the LHC will be equipped with a pixel detector system. The basic mechanical units of the pixel detector are multi chip modules. The main components of these modules are: 16 electronic chips, a controller chip and a large sensor tile, featuring more than 46000 sensor cells. MCM-D is a superior technique to build the necessary signal bus system and the power distribution system directly on the active sensor tile. In collaboration with the Fraunhofer Institute for Reliability and Microintegration, IZM, the thin film process is reviewed and enhanced. The multi layer system was designed and optimized for the interconnection system as well as for the 46000 pixel contacts. Laboratory measurements on prototypes prove that complex routing schemes for geometrically optimized single chips are suitable and have negligible influence on the front--end ...

Magneto-optic and electro-optic modulators

International Nuclear Information System (INIS)

Hutchinson, D.P.; Ma, C.H.; Price, T.R.; Staats, P.A.; Sluis, K.L.V.

1982-01-01

An important aspect of the Faraday rotation diagnostic for tokamak plasma measurement has been the development of suitable polarization modulators for submillimeter wavelength. The problems are to obtain high optical transmission and fast modulation frequencies. In ORNL, the authors have developed both a magneto-optic and an electro-optic submillimeter-wave modulators. These devices have been operated at modulation frequency of approximately 100 kHz, and both have high transmission. The original magneto-optic modulator consists of a 3 mm thick by 1.4 cm diameter 2-111 ferrite disk mounted at the center of an air core coil. Recently, a new ferrite modulator has been tested, which allows a much higher modulation frequency than the original device. A laboratory set-up designed to simulate a plasma heterodyne interferometer/polarimeter experiment has been used to determine the modulator characteristics. A mechanical polarization rotor was used to simulate the rotation by plasma. The transmission of the ferrite disk was 80 % at a wavelength of 0.447 mm. The authors have also performed preliminary measurement on an electro-optic modulator first demonstrated by Fetterman at Lincoln Laboratory, U.S. This device is a classical electro-optic modulator using a cryogenically cooled (4.2 K) LiTaO 3 crystal. Experiments are underway to determine the electro-optic properties of the crystal over the temperature range from 4.2 K to 77 K and over the range of wavelength from 0.118 mm to 0.447 mm. (Wakatsuki, Y.)

The CRESST-III detector module

Energy Technology Data Exchange (ETDEWEB)

Wuestrich, Marc [Max-Planck-Institut f. Physik (Werner-Heisenberg-Institut) (Germany); Collaboration: CRESST-Collaboration

2016-07-01

The direct dark matter experiment CRESST uses scintillating calorimeters to detected WIMP induced nuclear scattering in CaWO{sub 4} single crystals. Equipped with transition edge sensors (TESs), these detectors can achieve detection thresholds well below 1 keV. The last physics run of CRESST-II proved the high potential of the experiment especially for small WIMP masses and triggered the development of a new detector module using much smaller CaWO{sub 4} main absorbers. The upcoming CRESST-III run will mainly be equipped with these newly developed modules, which combine a fully scintillating detector housing with an improved detection threshold (<100 keV). While many features of the new module were adapted from previous module designs in an improved way, also new features are implemented like instrumented sticks (iSticks) holding the crystals and optimized TES structures for phonon and light detectors. First tests above ground validated the improved performance of these detector modules and promise to explore new regions in the WIMP parameter space in the next CRESST-III run.

Standard Chinese: A Modular Approach. Student Workbook. Module 3: Money; Module 4: Directions.

Science.gov (United States)

Defense Language Inst., Monterey, CA.

Texts in spoken Standard Chinese were developed to improve and update Chinese materials and to reflect current usage in Beijing and Taipei. The focus is on communicating in Chinese in practical situations. The overall course is organized into 10 situational modules, student workbooks, and resource modules. This workbook covers the money and…

Standard Chinese: A Modular Approach. Student Text. Module 3: Money; Module 4: Directions.

Science.gov (United States)

Defense Language Inst., Monterey, CA.

Texts in spoken Standard Chinese were developed to improve and update Chinese materials to reflect current usage in Beijing and Taipei. The focus is on communicating in practical situations, and the texts summarize and supplement tapes. The overall course is organized into 10 situational modules, student workbooks, and resource modules. This text…

Development of Nanofiller-Modulated Polymeric Oxygen Enrichment Membranes for Reduction of Nitrogen Oxides in Coal Combustion

Energy Technology Data Exchange (ETDEWEB)

Jianzhong Lou; Shamsuddin Ilias

2010-12-31

North Carolina A&T State University in Greensboro, North Carolina, has undertaken this project to develop the knowledge and the material to improve the oxygen-enrichment polymer membrane, in order to provide high-grade oxygen-enriched streams for coal combustion and gasification applications. Both experimental and theoretical approaches were used in this project. The membranes evaluated thus far include single-walled carbon nano-tube, nano-fumed silica polydimethylsiloxane (PDMS), and zeolite-modulated polyimide membranes. To document the nanofiller-modulated polymer, molecular dynamics simulations have been conducted to calculate the theoretical oxygen molecular diffusion coefficient and nitrogen molecular coefficient inside single-walled carbon nano-tube PDMS membranes, in order to predict the effect of the nano-tubes on the gas-separation permeability. The team has performed permeation and diffusion experiments using polymers with nano-silica particles, nano-tubes, and zeolites as fillers; studied the influence of nano-fillers on the self diffusion, free volume, glass transition, oxygen diffusion and solubility, and perm-selectivity of oxygen in polymer membranes; developed molecular models of single-walled carbon nano-tube and nano-fumed silica PDMS membranes, and zeolites-modulated polyimide membranes. This project partially supported three graduate students (two finished degrees and one transferred to other institution). This project has resulted in two journal publications and additional publications will be prepared in the near future.

Development of the air module for the work information management system. Environmental subsystem (WIMS-ES). Master's thesis

Energy Technology Data Exchange (ETDEWEB)

Cantwell, R.A.; Davis, J.S.

1992-09-01

The primary objective of this research was to develop the air module for the Work Information Management System Environmental Subsystem (WIMSES). The air module will provide Air Force environmental managers with a management information system (MIS) to control the growing amount of air pollution data required to stay in compliance with the newly amended Clean Air Act. To develop the air module, the Air Force's air pollution management requirements were researched first. These requirements were then compared to the capabilities of existing air pollution MISs used in the Department of Defense, the Environmental Protection Agency, and in commercial industry. The research led to a draft air nodule that tracks a base's source inventory and associated permit, control equipment, and emission information. Each base's data will be fully accessible to headquarters personnel through the fully networked WIMS-ES. The draft air nodule was validated through an Air Staff review, an Air Force review, and finally, a workshop with Air Force air pollution experts. The finalized air module has been forwarded to the WIMS-ES programmers and will become the Air Force-wide air pollution MIS in early 1993.... Air pollution, Environmental management, Data management, Data bases, Management information systems, Information systems.

Welding techniques development of CLAM steel for Test Blanket Module

Energy Technology Data Exchange (ETDEWEB)

Li Chunjing [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui, 230027 (China)], E-mail: lcj@ipp.ac.cn; Huang Qunying; Wu Qingsheng; Liu Shaojun [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui, 230027 (China); Lei Yucheng [Jiangsu University, Zhenjiang, Jiangsu, 212013 (China); Muroga, Takeo; Nagasaka, Takuya [National Institute for Fusion Science, Toki, Jifu, 509-5292 (Japan); Zhang Jianxun [Xi' an Jiaotong University, Xi' an, Shanxi, 710049 (China); Li Jinglong [Northwestern Polytechnical University, Xi' an, Shanxi, 710072 (China)

2009-06-15

Fabrication techniques for Test Blanket Module (TBM) with CLAM are being under development. Effect of surface preparation on the HIP diffusion bonding joints was studied and good joints with Charpy impact absorbed energy close to that of base metal have been obtained. The mechanical properties test showed that effect of HIP process on the mechanical properties of base metal was little. Uniaxial diffusion bonding experiments were carried out to study the effect of temperature on microstructure and mechanical properties. And preliminary experiments on Electron Beam Welding (EBW), Tungsten Inert Gas (TIG) Welding and Laser Beam Welding (LBW) were performed to find proper welding techniques to assemble the TBM. In addition, the thermal processes assessed with a Gleeble thermal-mechanical machine were carried out as well to assist the fusion welding research.

Research on modulated structure alloys

International Nuclear Information System (INIS)

Tsujimoto, Tokuzo; Saito, Kazuo; Hashimoto, Kenki

1982-01-01

Research was carried out for the purposes of clarifying the cause of modulated structure formation, developing the structure control method utilizing modulated structure and clarifying the suitability of modulated structure alloys as radiation damage-resisting materials. The research on structure control method encountered a difficulty in the analysis of experimental results, bu the following results were obtained in the other items. The method of solving a diffusion equation including a nonlinear term was found in course of the clarification of the cause of modulated structure formation. As a means of detecting faint unevenness in solid solution, of which the deviation of composition is a few %, the structure analysis method utilizing magnetic property was developed. This method was applied to Ni-9.6 at.% Ti alloy, and the process of expanding amplitude in composition variation in spinodal decomposition and the formation of solute atomshort region at the time of nucleation-growth were confirmed. Utilizing the high energy electron beam generated in a superhigh voltage electron microscope, electron beam irradiation experiment was carried out on precipitation hardening alloys with modulated structure. As the result, it was found that in Ni-Ti alloy, the amount of void swelling resistance showed the change with the increase of modulated structure period. (Kako, I.)

Photovoltaic module certification/laboratory accreditation criteria development: Implementation handbook

Energy Technology Data Exchange (ETDEWEB)

Osterwald, C.R. [National Renewable Energy Laboratory, Golden, CO (United States); Hammond, R.L.; Wood, B.D.; Backus, C.E.; Sears, R.L. [Arizona State Univ., Tempe, AZ (United States); Zerlaut, G.A. [SC-International, Inc., Tempe, AZ (United States); D`Aiello, R.V. [RD Associates, Tempe, AZ (United States)

1996-08-01

This document covers the second phase of a two-part program. Phase I provided an overview of the structure and function of typical product certification/laboratory accreditation programs. This report (Phase H) provides most of the draft documents that will be necessary for the implementation of a photovoltaic (PV) module certification/laboratory accreditation program. These include organizational documents such as articles of incorporation, bylaws, and rules of procedure, as well as marketing and educational program documents. In Phase I, a 30-member criteria development committee was established to guide, review and reach a majority consensus regarding criteria for a PV certification/laboratory accreditation program. Committee members represented PV manufacturers, end users, standards and codes organizations, and testing laboratories. A similar committee was established for Phase II; the criteria implementation committee consisted of 29 members. Twenty-one of the Phase I committee members also served on the Phase II committee, which helped to provide program continuity during Phase II.

Requirements for a Dynamic Solvent Extraction Module to Support Development of Advanced Technologies for the Recycle of Used Nuclear Fuel

Energy Technology Data Exchange (ETDEWEB)

Jack Law; Veronica Rutledge; Candido Pereira; Jackie Copple; Kurt Frey; John Krebs; Laura Maggos; Kevin Nichols; Kent Wardle; Pratap Sadasivan; Valmor DeAlmieda; David Depaoli

2011-06-01

The Department of Energy's Nuclear Energy Advanced Modeling and Simulation (NEAMS) Program has been established to create and deploy next generation, verified and validated nuclear energy modeling and simulation capabilities for the design, implementation, and operation of future nuclear energy systems to improve the U.S. energy security. As part of the NEAMS program, Integrated Performance and Safety Codes (IPSC's) are being produced to significantly advance the status of modeling and simulation of energy systems beyond what is currently available to the extent that the new codes be readily functional in the short term and extensible in the longer term. The four IPSC areas include Safeguards and Separations, Reactors, Fuels, and Waste Forms. As part of the Safeguards and Separations (SafeSeps) IPSC effort, interoperable process models are being developed that enable dynamic simulation of an advanced separations plant. A SafeSepss IPSC 'toolkit' is in development to enable the integration of separation process modules and safeguards tools into the design process by providing an environment to compose, verify and validate a simulation application to be used for analysis of various plant configurations and operating conditions. The modules of this toolkit will be implemented on a modern, expandable architecture with the flexibility to explore and evaluate a wide range of process options while preserving their stand-alone usability. Modules implemented at the plant-level will initially incorporate relatively simple representations for each process through a reduced modeling approach. Final versions will incorporate the capability to bridge to subscale models to provide required fidelity in chemical and physical processes. A dynamic solvent extraction model and its module implementation are needed to support the development of this integrated plant model. As a stand-alone application, it will also support solvent development of extraction flowsheets

Irreducible Specht modules are signed Young modules

OpenAIRE

Hemmer, David J.

2005-01-01

Recently Donkin defined signed Young modules as a simultaneous generalization of Young and twisted Young modules for the symmetric group. We show that in odd characteristic, if a Specht module $S^\\lambda$ is irreducible, then $S^\\lambda$ is a signed Young module. Thus the set of irreducible Specht modules coincides with the set of irreducible signed Young modules. This provides evidence for our conjecture that the signed Young modules are precisely the class of indecomposable self-dual module...

Development of a head and neck companion module for the quality of life-radiation therapy instrument (QOL-RTI)

International Nuclear Information System (INIS)

Trotti, Andy; Johnson, Darlene J.; Gwede, Clement; Casey, Linda; Sauder, Bonnie; Cantor, Alan; Pearlman, James

1998-01-01

Purpose/Objective: A review of available head and neck quality of life (QOL) instruments reveals them to inadequately address important radiation related side effects, or to be too cumbersome for routine use. The purpose of this study was to develop a head and neck disease specific module as a companion to the previously developed quality of life - radiation therapy instrument (QOL-RTI). The goal was to create a more complete, yet concise, head and neck site-specific module geared toward patients receiving radiation therapy for head and neck cancer. Methods and Materials: This exploratory study included 34 consecutive patients undergoing definitive radiotherapy over a 6-7 week course (60-79.8 Gy). We developed and administered a 14-item questionnaire to all eligible patients treated with radiotherapy for head and neck cancer who were not already registered in another research study assessing quality of life (e.g., RTOG). During the treatment period, the QOL-RTI general tool and the head and neck (H and N) module were administered as follows: at baseline, at week four (for test-retest), and at the end of the treatment period. For validation purposes the QOL-RTI/H and N was compared to the functional assessment cancer tool head and neck (FACT-H and N) questionnaire. The FACT-H and N was administered one time at week 4, on the same day as the QOL-RTI/H and N. This report includes the treatment phase of the study (during the course of radiation). Results: Mean age was 62 years (range 40-75). Internal consistency of the module was satisfactory (Chronbach's α = 0.85). Test-retest yielded a correlation coefficient of 0.90 (p < 0.001). Concurrent validity, established by comparing the module to the FACT/H and N , yielded a correlation coefficient of 0.85. Significant changes in quality of life scores during a course of radiation was noted for both general quality of life tool and the site specific module. For the head and neck module, the difference in the mean baseline

Development of an empirical dynamic model for a Nexa PEM fuel cell power module

Energy Technology Data Exchange (ETDEWEB)

Soltani, Mehdi; Mohammad Taghi Bathaee, S. [Power Systems Laboratory, Department of Electrical Engineering, K.N. Toosi University of Technology, 16317-14191 Tehran (Iran)

2010-12-15

The goal of this study is to develop a fuel cell model which is capable of characterizing fuel cell steady-state performance as well as dynamic behavior. In this paper a new dynamic model of a 1.2 kW Polymer Electrolyte Membrane Fuel Cell (PEMFC) is developed and validated through a series of experiments. The experimental results have been obtained from a Nexa trademark PEM fuel cell power module under different load conditions. Based on this model, a simulator software package has been developed using the MATLAB {sup registered} and Simulink {sup registered} software and simulation results have been carried out. The proposed model exhibits good agreement with experiment results in steady-state and dynamic performance. (author)

Design development of the Apollo command and service module thrust vector attitude control systems

Science.gov (United States)

Peters, W. H.

1978-01-01

Development of the Apollo thrust vector control digital autopilot (TVC DAP) was summarized. This is the control system that provided pitch and yaw attitude control during velocity change maneuvers using the main rocket engine on the Apollo service module. A list of ten primary functional requirements for this control system are presented, each being subordinate to a more general requirement appearing earlier on the list. Development process functions were then identified and the essential information flow paths were explored. This provided some visibility into the particular NASA/contractor interface, as well as relationships between the many individual activities.

Quantum model for electro-optical amplitude modulation.

Science.gov (United States)

Capmany, José; Fernández-Pousa, Carlos R

2010-11-22

We present a quantum model for electro-optic amplitude modulation, which is built upon quantum models of the main photonic components that constitute the modulator, that is, the guided-wave beamsplitter and the electro-optic phase modulator and accounts for all the different available modulator structures. General models are developed both for single and dual drive configurations and specific results are obtained for the most common configurations currently employed. Finally, the operation with two-photon input for the control of phase-modulated photons and the important topic of multicarrier modulation are also addressed.

Development of technology for thin substrate polycrystalline solar cells for practical use. Development of elementary technologies for low-cost polycrystalline cell modules; Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Takessho cell module tei cost ka yoso gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on development of elementary technologies for low-cost polycrystalline cell modules in fiscal 1994. (1) On development of elementary technologies for mass production, fast surface machining, fast electrode forming and fast forming of junctions and antireflection films were studied. Surface machining by rotating grindstone was studied as fast cutting of fine grooves on Si substrates, resulting in possible fast machining superior in shape accuracy. Electrode properties equivalent or superior to previous ones were obtained by fast electrode forming using a fast printing/sintering equipment even at transfer speed 7.5 times as high as that of conventional methods. Simultaneous fast forming of junctions and antireflection films were achieved by heat treatment after deposition on Si substrate surfaces while heat-decomposing Ti and P compound gas. (2) On development of module structure, an optimum cell group angle, low reflection rate at glass surface, and fast wiring were studied. 5 figs., 2 tabs.

Standard Chinese: A Modular Approach. Student Workbook. Module 1: Orientation; Module 2: Biographic Information.

Science.gov (United States)

Defense Language Inst., Monterey, CA.

Texts in spoken Standard Chinese were developed to improve and update Chinese materials to reflect current usage in Beijing and Taipei. The focus is on communicating in Chinese in practical situations. The overall course is organized into 10 modules, student workbooks, and resource modules. This workbook covers the orientation and biographic…

Towards co-packaging of photonics and microelectronics in existing manufacturing facilities

Science.gov (United States)

Janta-Polczynski, Alexander; Cyr, Elaine; Bougie, Jerome; Drouin, Alain; Langlois, Richard; Childers, Darrell; Takenobu, Shotaro; Taira, Yoichi; Lichoulas, Ted W.; Kamlapurkar, Swetha; Engelmann, Sebastian; Fortier, Paul; Boyer, Nicolas; Barwicz, Tymon

2018-02-01

The impact of integrated photonics on optical interconnects is currently muted by challenges in photonic packaging and in the dense integration of photonic modules with microelectronic components on printed circuit boards. Single mode optics requires tight alignment tolerance for optical coupling and maintaining this alignment in a cost-efficient package can be challenging during thermal excursions arising from downstream microelectronic assembly processes. In addition, the form factor of typical fiber connectors is incompatible with the dense module integration expected on printed circuit boards. We have implemented novel approaches to interfacing photonic chips to standard optical fibers. These leverage standard high throughput microelectronic assembly tooling and self-alignment techniques resulting in photonic packaging that is scalable in manufacturing volume and in the number of optical IOs per chip. In addition, using dense optical fiber connectors with space-efficient latching of fiber patch cables results in compact module size and efficient board integration, bringing the optics closer to the logic chip to alleviate bandwidth bottlenecks. This packaging direction is also well suited for embedding optics in multi-chip modules, including both photonic and microelectronic chips. We discuss the challenges and rewards in this type of configuration such as thermal management and signal integrity.

Adolescence Education: Physical Aspect, Module One; Social Aspects, Module Two; Sex Roles, Module Three; Sexually Transmitted Diseases, Module Four.

Science.gov (United States)

United Nations Educational, Scientific and Cultural Organization, Bangkok (Thailand). Principal Regional Office for Asia and the Pacific.

Adolescence Education is a family life education training program designed to assist young people in their physical, social, emotional, and moral development as they prepare for adulthood, marriage, parenthood, aging, and social relationships in the context of family and society. This package consists of four individually bound modules: (1)…

The ALICE silicon pixel detector front-end and read-out electronics

CERN Document Server

Kluge, A

2006-01-01

The ALICE silicon pixel detector (SPD) comprises the two innermost barrel layers of the ALICE inner tracker system. The SPD includes 120 half staves each of which consists of a linear array of 10 ALICE pixel chips bump bonded to two silicon sensors. Each pixel chip contains 8192 active cells, so the total number of pixel cells in the SPD is ≈107. The tight material budget and the limitation in physical dimensions required by the detector design introduce new challenges for the integration of the on-detector electronics. An essential part of the half stave is a low-mass multi-layer flex that carries power, ground, and signals to the pixel chips. Each half stave is read out using a multi-chip module (MCM). The MCM contains three radiation hard ASICs and an 800 Mbit/s custom developed optical link for the data transfer between the detector and the control room. The detector components are less than 3 mm thick. The production of the half-staves and MCMs is currently under way. Test results as well as on overvie...

ATLAS calorimetry. Trigger, simulation and jet calibration

Energy Technology Data Exchange (ETDEWEB)

Weber, P

2007-02-06

The Pre-Processor system of the ATLAS Level-1 Calorimeter Trigger performs complex processing of analog trigger tower signals from electromagnetic and hadronic calorimeters. The main processing block of the Pre-Processor System is the Multi-Chip Module (MCM). The first part of this thesis describes MCM quality assurance tests that have been developed, their use in the MCM large scale production and the results that have been obtained. In the second part of the thesis a validation of a shower parametrisation model for the ATLAS fast simulation package ATLFAST based on QCD dijet events is performed. A detailed comparison of jet response and jet energy resolution between the fast and the full simulation is presented. The uniformity of the calorimeter response has a significant impact on the accuracy of the jet energy measurement. A study of the calorimeter intercalibration using QCD dijet events is presented in the last part of the thesis. The intercalibration study is performed in azimuth angle {phi} and in pseudorapidity {eta}. The performance of the calibration methods including possible systematic and statistical effects is described. (orig.)

Development of e-module combining science process skills and dynamics motion material to increasing critical thinking skills and improve student learning motivation senior high school

Directory of Open Access Journals (Sweden)

Fengky Adie Perdana

2017-02-01

Full Text Available Learning media is one of the most components in the teaching and learning process. This research was conducted to design and develop the electronic modules combining science process skills and dynamics motion content for increasing critical thinking skills and improve student learning motivation for senior high school. The Methods used in this research is Research and Development (R&D. Model research and development using a research 4D Thiagarajan model. Physics module was developed using science process skills approach: observing, formulating the problem, formulating a hypothesis, identify variables, conduct experiments, analyse the data, summarise and communicate. The results showed that: 1 the electronics module has been developed by integrating the science process skills for enhancing critical thinking skills and student motivation. 2 Electronic Module Physics-based science process skills meet the criteria very well, judging from the results of validation content, validation media, validation of peer education and practitioners, with an average value of 3.80 is greater than the minimum eligibility 3.78. 3 effectiveness the modules of science process skills got N-gain value obtained from a large trial in grade samples of 0.67 and 0.59 in the control group were categorised as moderate. 4 Implementation of electronic modules Physics-based science process skills is considered an effective to enhance the students' motivation. Statistical analysis showed a significance value of 0.027 is lower than the significance level α = 0.05, this means that there are significant differences between learning motivation grade sample and the control class. As a result of analysis data obtained from the research, it was seen that the students' motivation that uses Physics module based science process skills better than conventional learning.

Unilateral deafness in children affects development of multi-modal modulation and default mode networks

Directory of Open Access Journals (Sweden)

Vincent eSchmithorst

2014-03-01

Full Text Available Monaural auditory input due to congenital or acquired unilateral hearing loss (UHL may have neurobiological effects on the developing brain. Using fMRI, we investigated the effect of UHL on the development of functional brain networks used for cross-modal processing. Children ages 7-12 with moderate or greater unilateral hearing loss of sensorineural origin (UHL-SN; N = 21 and normal-hearing controls (N = 23 performed an fMRI-compatible adaptation of the Token Test involving listening to a sentence such as touched the small green circle and the large blue square and simultaneously viewing an arrow touching colored shapes on a video. Children with right or severe-to-profound UHL-SN displayed smaller activation in a region encompassing the right inferior temporal, middle temporal, and middle occipital gyrus (BA 19/37/39, evidencing differences due to monaural hearing in cross-modal modulation of the visual processing pathway. Children with UHL-SN displayed increased activation in the left posterior superior temporal gyrus, likely the result either of more effortful low-level processing of auditory stimuli or differences in cross-modal modulation of the auditory processing pathway. Additionally, children with UHL-SN displayed reduced deactivation of anterior and posterior regions of the default mode network. Results suggest that monaural hearing affects the development of brain networks related to cross-modal sensory processing and the regulation of the default network during processing of spoken language.

Plant Growth Research for Food Production: Development and Testing of Expandable Tuber Growth Module

Science.gov (United States)

Cordova, Brennan A.

2017-01-01

Controlled and reliable growth of a variety of vegetable crops is an important capability for manned deep space exploration systems for providing nutritional supplementation and psychological benefits to crew members. Because current systems have been limited to leafy vegetables that require minimal root space, a major goal for these systems is to increase their ability to grow new types of crops, including tuber plants and root vegetables that require a large root space. An expandable root zone module and housing was developed to integrate this capability into the Veggie growth system. The expandable module uses a waterproof, gas-permeable bag with a structure that allows for root space to increase vertically throughout the growth cycle to accommodate for expanding tuber growth, while minimizing the required media mass. Daikon radishes were chosen as an ideal tuber crop for their subterraneous tuber size and rapid growth cycle, and investigations were done to study expanding superabsorbent hydrogels as a potential growth media. These studies showed improved water retention, but restricted oxygen availability to roots with pure gel media. It was determined that these hydrogels could be integrated in lower proportions into standard soil to achieve media expansion and water retention desired. Using the constructed module prototype and ideal gel and soil media mixture, Daikon radishes were grown in the system to test the capability and success of the system through a full growth cycle.

The Needs Analysis in Self-Concept Module Development

Science.gov (United States)

Yusop, Yusni Mohamad; Sumari, Melati; Mohamed, Fatanah; Said, Shahriza; Azeez, Mohd Ibrahim K.; Jamil, Mohd Ridhuan Mohd

2015-01-01

This research studies needs analyses conducted to examine the need for a self-concept module. Two types of analyses had been conducted; content analysis and experts' consensus. Content analysis was conducted to explore the issues of self-concept from the theory and literature perspective. Later, needs analysis had also been carried out to observe…

Spatial Terahertz Modulator

Science.gov (United States)

Xie, Zhenwei; Wang, Xinke; Ye, Jiasheng; Feng, Shengfei; Sun, Wenfeng; Akalin, Tahsin; Zhang, Yan

2013-11-01

Terahertz (THz) technology is a developing and promising candidate for biological imaging, security inspection and communications, due to the low photon energy, the high transparency and the broad band properties of the THz radiation. However, a major encountered bottleneck is lack of efficient devices to manipulate the THz wave, especially to modulate the THz wave front. A wave front modulator should allow the optical or electrical control of the spatial transmission (or reflection) of an input THz wave and hence the ability to encode the information in a wave front. Here we propose a spatial THz modulator (STM) to dynamically control the THz wave front with photo-generated carriers. A computer generated THz hologram is projected onto a silicon wafer by a conventional spatial light modulator (SLM). The corresponding photo-generated carrier spatial distribution will be induced, which forms an amplitude hologram to modulate the wave front of the input THz beam. Some special intensity patterns and vortex beams are generated by using this method. This all-optical controllable STM is structure free, high resolution and broadband. It is expected to be widely used in future THz imaging and communication systems.

Development Module Oriented Science Technology Society Indue Science Literacy Assessment for 7th-Grade Junior High School Students in 2nd -Semester

Science.gov (United States)

Arbi, Y. R.; Sumarmin, R.; Putri, D. H.

2018-04-01

The problem in the science learning process is the application of the scientific approach takes a long time in order to provide conceptual understanding to the students, there is no teaching materials that can measure students reasoning and thinking ability, and the assessment has not measured students reasoning and literacy skills.The effort can be done is to develop science technology society module indue science literacy assessment. The purpose of the research was to produce a module oriented society indue science science technology literacy assessment. The research is development research using Plomp model, consist of preliminary, prototyping, and assessment phase. Data collect by questionnare and documantion. The result there is science technology society module indue science literacy assessment is very valid.

Standard Chinese: A Modular Approach. Student Text. Module 1: Orientation; Module 2: Biographic Information.

Science.gov (United States)

Defense Language Inst., Monterey, CA.

Texts in spoken Standard Chinese were developed to improve and update Chinese materials to reflect current usage in Beijing and Taipei. The focus is on communicating in Chinese in practical situations, and the texts summarize and supplement tapes. The overall course is organized into 10 situational modules, student workbooks, and resource modules.…

Signed Young Modules and Simple Specht Modules

OpenAIRE

Danz, Susanne; Lim, Kay Jin

2015-01-01

By a result of Hemmer, every simple Specht module of a finite symmetric group over a field of odd characteristic is a signed Young module. While Specht modules are parametrized by partitions, indecomposable signed Young modules are parametrized by certain pairs of partitions. The main result of this article establishes the signed Young module labels of simple Specht modules. Along the way we prove a number of results concerning indecomposable signed Young modules that are of independent inter...

Growth Modulation in Achondroplasia.

Science.gov (United States)

McClure, Philip K; Kilinc, Eray; Birch, John G

2017-09-01

Achondroplasia is the most common skeletal dysplasia with a rate of nearly 1/10,000. The development of lower extremity deformity is well documented, and various modes of correction have been reported. There are no reports on the use of growth modulation to correct angular deformity in achondroplasia. Medical Records from 1985 to 2015 were reviewed for the diagnosis of achondroplasia and growth modulation procedures. Patients who had been treated for angular deformity of the legs by growth modulation were identified. A detailed analysis of their medical record and preoperative and final lower extremity radiographs was completed. Four patients underwent growth modulation procedures, all to correct existing varus deformity of the legs. Three of the 4 patients underwent bilateral distal femoral and proximal tibial growth modulation. The remaining patient underwent tibial correction only. Two of the 4 patients had a combined proximal fibular epiphysiodesis. All limbs had some improvement of alignment; however, 1 patient went on to bilateral osteotomies. Only 1 limb corrected to a neutral axis with growth modulation alone at last follow-up, initial implantation was done before 5 years of age. Growth modulation is an effective means for deformity correction in the setting of achondroplasia. However implantation may need to be done earlier than would be typical for patients without achondroplasia. Osteotomy may still be required after growth modulation for incomplete correction.

Acquisition system for the CLIC Module

CERN Document Server

Vilalte, Sebastien

2011-01-01

The status of R&D activities for CLIC module acquisition are discussed [1]. LAPP is involved in the design of the local CLIC module acquisition crate, described in the document Study of the CLIC Module Front-End Acquisition and Evaluation Electronics [2]. This acquisition system is a project based on a local crate, assigned to the CLIC module, including several mother boards. These motherboards are foreseen to hold mezzanines dedicated to the different subsystems. This system has to work in radiation environment. LAPP is involved in the development of Drive Beam stripline position monitors read-out, described in the document Drive Beam Stripline BPM Electronics and Acquisition [3]. LAPP also develops a generic acquisition mezzanine that allows to perform all-around acquisition and components tests for drive beam stripline BPM read-out.

Development of additional module to neutron-physic and thermal-hydraulic computer codes for coolant acoustical characteristics calculation

Energy Technology Data Exchange (ETDEWEB)

Proskuryakov, K.N.; Bogomazov, D.N.; Poliakov, N. [Moscow Power Engineering Institute (Technical University), Moscow (Russian Federation)

2007-07-01

The new special module to neutron-physic and thermal-hydraulic computer codes for coolant acoustical characteristics calculation is worked out. The Russian computer code Rainbow has been selected for joint use with a developed module. This code system provides the possibility of EFOCP (Eigen Frequencies of Oscillations of the Coolant Pressure) calculations in any coolant acoustical elements of primary circuits of NPP. EFOCP values have been calculated for transient and for stationary operating. The calculated results for nominal operating were compared with results of measured EFOCP. For example, this comparison was provided for the system: 'pressurizer + surge line' of a WWER-1000 reactor. The calculated result 0.58 Hz practically coincides with the result of measurement (0.6 Hz). The EFOCP variations in transients are also shown. The presented results are intended to be useful for NPP vibration-acoustical certification. There are no serious difficulties for using this module with other computer codes.

Development of additional module to neutron-physic and thermal-hydraulic computer codes for coolant acoustical characteristics calculation

International Nuclear Information System (INIS)

Proskuryakov, K.N.; Bogomazov, D.N.; Poliakov, N.

2007-01-01

The new special module to neutron-physic and thermal-hydraulic computer codes for coolant acoustical characteristics calculation is worked out. The Russian computer code Rainbow has been selected for joint use with a developed module. This code system provides the possibility of EFOCP (Eigen Frequencies of Oscillations of the Coolant Pressure) calculations in any coolant acoustical elements of primary circuits of NPP. EFOCP values have been calculated for transient and for stationary operating. The calculated results for nominal operating were compared with results of measured EFOCP. For example, this comparison was provided for the system: 'pressurizer + surge line' of a WWER-1000 reactor. The calculated result 0.58 Hz practically coincides with the result of measurement (0.6 Hz). The EFOCP variations in transients are also shown. The presented results are intended to be useful for NPP vibration-acoustical certification. There are no serious difficulties for using this module with other computer codes

Development of microstrip gas chamber and application to imaging gamma-ray detector

International Nuclear Information System (INIS)

Tanimori, T.; Minami, S.; Nagae, T.; Takahashi, T.; Miyagi, T.

1992-07-01

We have developed Microstrip Gas Chamber (MSGC) by using Multi-Chip technology which enables high-density assembly of bare LSI chips on a silicon board. Our MSGC was operated steadily with ∼ 10 3 gain more than one week. An energy resolution of 15% (FWHM) for 5.9 keV X-ray of 55 Fe was obtained. With very thin polyimide substrate of 16 μm thickness, two interesting phenomena were observed; one is a strong dependence of gains on the back plane potential, and the other is little time variation of gains. New type of MSGC with a guarding mask of a thin polyimide layer on the cathode edges has been examined to reduce incidental electrical discharges between anode and cathode strips. Furthermore, new approach to reduce the resistivity of the substrate has been examined. By these approaches, the stability of the high gain operation of ∼ 10 4 has been drastically improved. In addition, we discuss the possibility of the application of MSGC to the coded mask X-ray imaging detector for astrophysics. (author)

Development of Health Education Learning Module in Bac.TSE-LDPE Programme in TTI: Needs Analysis Study

Science.gov (United States)

Ujang, Alijah; Alias, Norlidah; Siraj, Saedah

2015-01-01

This study is to explore the need to develop learning modules of health education for trainee teachers in the Bachelor Of Teaching (Hons)(Special Education-Learning Disabilities For Primary Education) Programme (Bac.TSE-LDPE) in the Teacher Training Institute (TTI). The questionnaire uses the Likert scale with the close ended questions analysed by…

Application of high power modulated intense relativistic electron beams for development of Wake Field Accelerator

International Nuclear Information System (INIS)

Friedman, M.

1989-01-01

This final Progress Report addresses DOE-sponsored research on the development of future high-gradient particle accelerators. The experimental and the theoretical research, which lasted three years, investigated the Two Beam Accelerator (TBA). This high-voltage-gradient accelerator was powered by a modulated intense relativistic electron beam (MIREB) of power >10 10 watts. This research was conceived after a series of successful experiments performed at NRL generating and using MIREBs. This work showed that an RF structure could be built which was directly powered by a modulated intense relativistic electron beam. This structure was then used to accelerate a second electron beam. At the end of the three year project the proof-of-principle accelerator demonstrated the generation of a high current beam of electrons with energy >60 MeV. Scaling laws needed to design practical devices for future applications were also derived

Development of Modulators Against Degenerative Aging Using Radiation Fusion Technology

International Nuclear Information System (INIS)

Jo, Sung Kee; Jung, U.; Park, H. R.

2010-04-01

In this study, we selected final 20 biomarkers for the degenerative aging to develop radiation aging modeling, and validated a few of selected markers to utilize them in the screening of aging modulators. To select the biomarkers of the degenerative aging, 4 categories of aging-related markers (immune/hematopoiesis, oxidative damage, signaling molecule, lipid metabolism) were comparatively analyzed in irradiated and normally aged biosystems (cell lines or mice). In result, most of the biomarkers showed similar changes by irradiation and normal aging. Regarding the immune/hematopoiesis, the decline of immune cell functions (lymphocyte, NK cell) and Th1/Th2 imbalance, and decreased antigen-presenting of dendritic cells were observed and 10 biomarkers were selected in this category. mtDNA deletion was selected for the oxidative damage marker, 6 biomarkers including p21 and p-FOXO3a for signaling molecule biomarkers, and 3 biomarkers including the adipose tissue weight were selected for lipid metabolism. In addition, the various radiation application conditions by single/factionated irradiation and the periods after the irradiation were investigated for the optimal induction of changes of biomarker, which revealed that total 5Gy of 10 or more fractionated irradiations and 4 months or greather period were observed to be optimal. To found the basis for the screening of natural aging modulators, some selected aging biomarkers were validated by their inhibition by well-known natural agents (EGCG, HemoHIM, etc) in aged cell or mouse model. Additionally, by evaluating the reductive efficacy of 5 natural agents on the degeneration of skin and reproductive organs induced by radiation and chemicals (cyclophosphamide, etc), we established the base for the screening of degenerative diseases by various factors

Development of Modulators Against Degenerative Aging Using Radiation Fusion Technology

Energy Technology Data Exchange (ETDEWEB)

Jo, Sung Kee; Jung, U.; Park, H. R.

2010-04-15

In this study, we selected final 20 biomarkers for the degenerative aging to develop radiation aging modeling, and validated a few of selected markers to utilize them in the screening of aging modulators. To select the biomarkers of the degenerative aging, 4 categories of aging-related markers (immune/hematopoiesis, oxidative damage, signaling molecule, lipid metabolism) were comparatively analyzed in irradiated and normally aged biosystems (cell lines or mice). In result, most of the biomarkers showed similar changes by irradiation and normal aging. Regarding the immune/hematopoiesis, the decline of immune cell functions (lymphocyte, NK cell) and Th1/Th2 imbalance, and decreased antigen-presenting of dendritic cells were observed and 10 biomarkers were selected in this category. mtDNA deletion was selected for the oxidative damage marker, 6 biomarkers including p21 and p-FOXO3a for signaling molecule biomarkers, and 3 biomarkers including the adipose tissue weight were selected for lipid metabolism. In addition, the various radiation application conditions by single/factionated irradiation and the periods after the irradiation were investigated for the optimal induction of changes of biomarker, which revealed that total 5Gy of 10 or more fractionated irradiations and 4 months or greather period were observed to be optimal. To found the basis for the screening of natural aging modulators, some selected aging biomarkers were validated by their inhibition by well-known natural agents (EGCG, HemoHIM, etc) in aged cell or mouse model. Additionally, by evaluating the reductive efficacy of 5 natural agents on the degeneration of skin and reproductive organs induced by radiation and chemicals (cyclophosphamide, etc), we established the base for the screening of degenerative diseases by various factors

Designing Interactive Electronic Module in Chemistry Lessons

Science.gov (United States)

Irwansyah, F. S.; Lubab, I.; Farida, I.; Ramdhani, M. A.

2017-09-01

This research aims to design electronic module (e-module) oriented to the development of students’ chemical literacy on the solution colligative properties material. This research undergoes some stages including concept analysis, discourse analysis, storyboard design, design development, product packaging, validation, and feasibility test. Overall, this research undertakes three main stages, namely, Define (in the form of preliminary studies); Design (designing e-module); Develop (including validation and model trial). The concept presentation and visualization used in this e-module is oriented to chemical literacy skills. The presentation order carries aspects of scientific context, process, content, and attitude. Chemists and multi media experts have done the validation to test the initial quality of the products and give a feedback for the product improvement. The feasibility test results stated that the content presentation and display are valid and feasible to be used with the value of 85.77% and 87.94%. These values indicate that this e-module oriented to students’ chemical literacy skills for the solution colligative properties material is feasible to be used.

Modulation of ovarian steroidogenesis by adiponectin during delayed embryonic development of Cynopterus sphinx.

Science.gov (United States)

Anuradha; Krishna, Amitabh

2014-09-01

The aim of present study was to evaluate role of adiponectin in ovarian steroidogenesis during delayed embryonic development of Cynopterus sphinx. This study showed significantly low circulating adiponectin level and a decline in expression of adiponectin receptor 1 (AdipoR1) in the ovary during the period of delayed embryonic development as compared with the normal development. The adiponectin treatment in vivo during the period of delayed development caused significantly increased in circulating progesterone and estradiol levels together with increased expression of AdipoR1 in the ovary. The in vitro study confirmed the stimulatory effect of adiponectin on progesterone synthesis. Both in vivo and in vitro studies showed that the effects of adiponectin on ovarian steroidogenesis were mediated through increased expression of luteinizing hormone-receptor, steroidogenic acute regulatory protein and 3β-hydroxyl steroid dehydrogenase enzyme. The adiponectin treatment may also promote progesterone synthesis by modulating ovarian angiogenesis, cell survival and rate of apoptosis. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development of High Performance Cooling Modules in Notebook PC's

Science.gov (United States)

Tanahashi, Kosei

The CPU power consumption in Notebook PCs is increasing every year. Video chips and HDDs are also continually using larger power for higher performance. In addition, since miniaturization is desired, the mounting of components is becoming more and more dense. Accordingly, the cooling mechanisms are increasingly important. The cooling modules have to dissipate larger amounts of heat in the same environmental conditions. Therefore, high capacity cooling capabilities is needed, while low costs and high reliability must be retained. Available cooling methods include air or water cooling systems and the heat conduction method. The air cooling system is to transmit heat by a cooling fan often using a heat pipe. The water cooling one employs the water to carry heat to the back of the display, which offers a comparatively large cooling area. The heat conduction method is to transfer the heat by thermal conduction to the case. This article describes the development of new and comparatively efficient cooling devices offering low cost and high reliability for air cooling system. As one of the development techniques, the heat resistance and performance are measured for various parts and layouts. Each cooling system is evaluated in the same measurement environment. With regards to the fans, an optimal shape of the fan blades to maximize air flow is found by using CFD simulation, and prototypes were built and tested.

Development of welding technologies for the manufacturing of European Tritium Breeder blanket modules

Energy Technology Data Exchange (ETDEWEB)

Poitevin, Y., E-mail: yves.poitevin@f4e.europa.eu [Fusion for Energy (F4E), Barcelona (Spain); Aubert, Ph. [CEA Saclay, DEN/DM2S and DEN/DMN, F-91191 Gif-sur-Yvette (France); Diegele, E. [Fusion for Energy (F4E), Barcelona (Spain); Dinechin, G. de [CEA Saclay, DEN/DM2S and DEN/DMN, F-91191 Gif-sur-Yvette (France); Rey, J. [Institut fuer Neutronenphysik und Reaktortechnik, FZK, Karlsruhe (Germany); Rieth, M. [Institut fuer Materialforschung I, FZK, Karlsruhe (Germany); Rigal, E. [CEA Grenoble, DRT/DTH, F-38000 Grenoble (France); Weth, A. von der [Institut fuer Neutronenphysik und Reaktortechnik, FZK, Karlsruhe (Germany); Boutard, J.-L. [European Fusion Development Agreement (EFDA), Garching (Germany); Tavassoli, F. [CEA Saclay, DEN/DM2S and DEN/DMN, F-91191 Gif-sur-Yvette (France)

2011-10-01

Europe has developed two reference Tritium Breeder Blankets concepts for a DEMO fusion reactor: the Helium-Cooled Lithium-Lead and the Helium-Cooled Pebble-Bed. Both are using the reduced-activation ferritic-martensitic EUROFER-97 steel as structural material and will be tested in ITER under the form of test blanket modules. The fabrication of their EUROFER structures requires developing welding processes like laser, TIG, EB and diffusion welding often beyond the state-of-the-art. The status of European achievements in this area is reviewed, illustrating the variety of processes and key issues behind retained options, in particular with respect to metallurgical aspects and mechanical properties. Fabrication of mock-ups is highlighted and their characterization and performances with respect to design requirements are reviewed.

Passive cooling of standalone flat PV module with cotton wick structures

International Nuclear Information System (INIS)

Chandrasekar, M.; Suresh, S.; Senthilkumar, T.; Ganesh karthikeyan, M.

2013-01-01

Highlights: • A simple passive cooling system is developed for standalone flat PV modules. • 30% Reduction in module temperature is observed with developed cooling system. • 15.61% Increase in output power of PV module is found with developed cooling system. • Module efficiency is increased by 1.4% with cooling arrangement. • Lower thermal degradation due to narrow range of temperature characteristics. - Abstract: In common, PV module converts only 4–17% of the incoming solar radiation into electricity. Thus more than 50% of the incident solar energy is converted as heat and the temperature of PV module is increased. The increase in module temperature in turn decreases the electrical yield and efficiency of the module with a permanent structural damage of the module due to prolonged period of thermal stress (also known as thermal degradation of the module). An effective way of improving efficiency and reducing the rate of thermal degradation of a PV module is to reduce the operating temperature of PV module. This can be achieved by cooling the PV module during operation. Hence in the present work, a simple passive cooling system with cotton wick structures is developed for standalone flat PV modules. The thermal and electrical performance of flat PV module with cooling system consisting of cotton wick structures in combination with water, Al 2 O 3 /water nanofluid and CuO/water nanofluid are investigated experimentally. The experimental results are also compared with the thermal and electrical performance of flat PV module without cooling system

Development of a multifunction module for the neutron electric dipole moment experiment at PSI

Energy Technology Data Exchange (ETDEWEB)

Bourrion, O., E-mail: olivier.bourrion@lpsc.in2p3.fr [Laboratoire de Physique Subatomique et de Cosmologie, Université Joseph Fourier Grenoble 1, CNRS/IN2P3, Institut Polytechnique de Grenoble, 53, Rue des Martyrs, Grenoble (France); Pignol, G. [Laboratoire de Physique Subatomique et de Cosmologie, Université Joseph Fourier Grenoble 1, CNRS/IN2P3, Institut Polytechnique de Grenoble, 53, Rue des Martyrs, Grenoble (France); Rebreyend, D. [Laboratoire de Physique Subatomique et de Cosmologie, Université Joseph Fourier Grenoble 1, CNRS/IN2P3, Institut Polytechnique de Grenoble, 53, Rue des Martyrs, Grenoble (France); Paul Scherrer Institut (PSI), CH-5232 Villigen PSI (Switzerland); Vescovi, C. [Laboratoire de Physique Subatomique et de Cosmologie, Université Joseph Fourier Grenoble 1, CNRS/IN2P3, Institut Polytechnique de Grenoble, 53, Rue des Martyrs, Grenoble (France)

2013-02-11

Experiments aiming at measuring the neutron electric dipole moment (nEDM) are at the forefront of precision measurements and demand instrumentation of increasing sensitivity and reliability. In this paper, we report on the development of a dedicated acquisition and control electronics board for the nEDM experiment at the Paul Scherrer Institute (PSI) in Switzerland. This multifunction module is based on a FPGA (Field Programmable Gate Array) which allows an optimal combination of versatility and evolution capacities.

PENGEMBANGAN MODUL LATIHAN FORGIVENESS UNTUK SISWA SMA DI KOTA MALANG

Directory of Open Access Journals (Sweden)

Ari Dwi Yudhianto

2016-12-01

Full Text Available This research aims to develop a training modules forgiveness based on the appraisement of experts (reviewers and high school student's response to the training modules forgiveness that have been developed. This study adapting the model development of Borg and Gall (1983, while the structure of the writing module refers to the guide preparation of module which prepared by the Director General module PMPTK (2008. The results of this study are drafting a training module forgiveness for senior high school students in Malang. Based appraisement materials experts, media specialists, and linguists classified as good, according to school counselors classified very good and yield response of students classified as good. So, that these modules worthy be used in the awarding of guidance services in schools. Penelitian ini bertujuan untuk mengembangkan modul latihan forgiveness  berdasarkan penilaian para ahli (reviewer dan respon siswa SMA terhadap Modul latihan forgiveness yang telah dikembangkan. Penelitian ini mengadaptasi model pengembangan Borg and gall (1983, sedangkan struktur penulisan modul mengacu pada panduan penyusunan modul yang disusun oleh dirjen PMPTK (2008. Hasil penelitian ini adalah tersusunnya modul latihan forgiveness untuk siswa SMA di Kota Malang yang berdasarkan penilaian ahli materi, ahli media, dan ahli bahasa tergolong baik, menurut konselor sekolah tergolong sangat baik dan hasil respon siswa tergolong baik. sehingga modul ini layak digunakan dalam pemberian layanan bimbingan di sekolah.

Development of a Schottky CdTe Medipix3RX hybrid photon counting detector with spatial and energy resolving capabilities

Energy Technology Data Exchange (ETDEWEB)

Gimenez, E.N., E-mail: Eva.Gimenez@diamond.ac.uk [Diamond Light Source, Harwell Campus, Oxforshire OX11 0DE (United Kingdom); Astromskas, V. [University of Surrey (United Kingdom); Horswell, I.; Omar, D.; Spiers, J.; Tartoni, N. [Diamond Light Source, Harwell Campus, Oxforshire OX11 0DE (United Kingdom)

2016-07-11

A multichip CdTe-Medipix3RX detector system was developed in order to bring the advantages of photon-counting detectors to applications in the hard X-ray range of energies. The detector head consisted of 2×2 Medipix3RX ASICs bump-bonded to a 28 mm×28 mm e{sup −} collection Schottky contact CdTe sensor. Schottky CdTe sensors undergo performance degrading polarization which increases with temperature, flux and the longer the HV is applied. Keeping the temperature stable and periodically refreshing the high voltage bias supply was used to minimize the polarization and achieve a stable and reproducible detector response. This leads to good quality images and successful results on the energy resolving capabilities of the system. - Highlights: • A high atomic number (CdTe sensor based) photon-counting detector was developed. • Polarization effects affected the image were minimized by regularly refreshing the bias voltage and stabilizing the temperature. • Good spatial resolution and image quality was achieved following this procedure.

Development of a European Organization for Research and Treatment of Cancer Module to Assess the Quality of Life of Patients With Proctitis After Pelvic Radiotherapy for Malignancy

International Nuclear Information System (INIS)

Spry, Nigel; Halkett, Georgia; Aoun, Samar; Spry, Jane; Yeoh, Eric

2008-01-01

Purpose: To describe the development of a proctitis-specific quality-of-life module to supplement the European Organization for Research and Treatment of Cancer Quality of Life Questionnaire (EORTC QLQ-C30). Methods and Materials: The module was developed according to EORTC guidelines, which consisted of an extensive literature review to identify previously described issues and interviews conducted with seven health professionals and 10 patients to rationalize the item list for construction into a provisional module. The module developed was then pretested with 28 patients and five health professionals. Results: The final module contains 21-items that are suitable to obtain information about the patients' quality of life after high-dose pelvic irradiation. The questionnaire has now been translated into four languages and commenced field testing in late 2007. Conclusions: The EORTC QLQ-C30, supplemented by EORTC QLQ-PRT21, will enable health professionals to more accurately monitor the side effects that patients experience after pelvic irradiation

The Development Of Learning Sets And Research Methodology Module Using Problem Based Learning For Accounting Education Students

OpenAIRE

Thomas, Partono; Nurkhin, Ahmad

2016-01-01

Improving the learning process is very important for every lecturer by implement innovative learning methods or media. The purpose of this study is to develop a research methodology learning instruction and module based of problem based learning for accounting education students. This research applied research and development design in the research methodology course in Economics Education (Accounting) Department, Faculty Of Economics, Semarang State University. Data analysis was used to test...

Optical readout and control interface for the BTeV pixel vertex detector

CERN Document Server

Vergara-Limon, S; Sheaff, M; Vargas, M A

2002-01-01

Optical links will be used for sending data back and forth from the counting room to the detector in the data acquisition systems for future high energy physics experiments, including ATLAS and CMS in the LHC at CERN (Switzerland) and BTeV at Fermilab (USA). This is because they can be ultra-high speed and are relatively immune to electro-magnetic interference (EMI). The baseline design for the BTeV Pixel Vertex Detector includes two types of optical link, one to control and monitor and the other to read out the hit data from the multi-chip modules on each half-plane of the detector. The design and performance of the first prototype of the Optical Readout and Control Interface for the BTeV Pixel Vertex Detector is described.

Final Design of the SLAC P2 Marx Klystron Modulator

Energy Technology Data Exchange (ETDEWEB)

Kemp, M.A.; Benwell, A.; Burkhart, C.; Larsen, R.; MacNair, D.; Nguyen, M.; Olsen, J.; /SLAC

2011-11-08

The SLAC P2 Marx has been under development for two years, and follows on the P1 Marx as an alternative to the baseline klystron modulator for the International Linear Collider. The P2 Marx utilizes a redundant architecture, air-insulation, a control system with abundant diagnostic access, and a novel nested droop correction scheme. This paper is an overview of the design of this modulator. There are several points of emphasis for the P2 Marx design. First, the modulator must be compatible with the ILC two-tunnel design. In this scheme, the modulator and klystron are located within a service tunnel with limited access and available footprint for a modulator. Access to the modulator is only practical from one side. Second, the modulator must have high availability. Robust components are not sufficient alone to achieve availability much higher than 99%. Therefore, redundant architectures are necessary. Third, the modulator must be relatively low cost. Because of the large number of stations in the ILC, the investment needed for the modulator components is significant. High-volume construction techniques which take advantage of an economy of scale must be utilized. Fourth, the modulator must be simple and efficient to maintain. If a modulator does become inoperable, the MTTR must be small. Fifth, even though the present application for the modulator is for the ILC, future accelerators can also take advantage of this development effort. The hardware, software, and concepts developed in this project should be designed such that further development time necessary for other applications is minimal.

Development of GPCR modulation of GABAergic transmission in chicken nucleus laminaris neurons.

Directory of Open Access Journals (Sweden)

Zheng-Quan Tang

Full Text Available Neurons in the nucleus laminaris (NL of birds act as coincidence detectors and encode interaural time difference to localize the sound source in the azimuth plane. GABAergic transmission in a number of CNS nuclei including the NL is subject to a dual modulation by presynaptic GABA(B receptors (GABA(BRs and metabotropic glutamate receptors (mGluRs. Here, using in vitro whole-cell patch clamp recordings from acute brain slices of the chick, we characterized the following important but unknown properties pertaining to such a dual modulation: (1 emergence of functional GABA synapses in NL neurons; (2 the temporal onset of neuromodulation mediated by GABA(BRs and mGluRs; and (3 the physiological conditions under which GABA(BRs and mGluRs are activated by endogenous transmitters. We found that (1 GABA(AR-mediated synaptic responses were observed in about half of the neurons at embryonic day 11 (E11; (2 GABA(BR-mediated modulation of the GABAergic transmission was detectable at E11, whereas the modulation by mGluRs did not emerge until E15; and (3 endogenous activity of GABA(BRs was induced by both low- (5 or 10 Hz and high-frequency (200 Hz stimulation of the GABAergic pathway, whereas endogenous activity of mGluRs was induced by high- (200 Hz but not low-frequency (5 or 10 Hz stimulation of the glutamatergic pathway. Furthermore, the endogenous activity of mGluRs was mediated by group II but not group III members. Therefore, autoreceptor-mediated modulation of GABAergic transmission emerges at the same time when the GABA synapses become functional. Heteroreceptor-mediated modulation appears at a later time and is receptor type dependent in vitro.

Actuator Module of Robot Manipulator for Nuclear Power Plants Inspection, Maintenance and Decommission

Energy Technology Data Exchange (ETDEWEB)

Lee, Sung Uk; Jung, Kyung Min; Seo, Young Chil; Choi, Byung Seon; Moon, Jei Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-10-15

For nuclear facility decommissioning, there are many different electrical manipulators to remotely dismantle a nuclear facility. Various manipulators will be necessary for inspection, maintenance and decommission. Only one manipulator cannot response to many required tasks. Therefore, several manipulators are necessary, depending on the payload capacity, their number of axes and their dexterity. Each manipulator was developed for a specific task. The actuators used at manipulator are varied and many companies sell actuators depending on power, torque and speed. However, the commercial product is not standardized. Therefore, the development of the manipulator is time consuming and expensive. The essential item of the manipulators is the actuator module. If actuator module is standardized, it is easier to develop manipulator. In this paper, we developed two electrical actuator modules to standardize the actuator module and easily develop a manipulator using the proposed actuator modules. The electrical actuator module has a motor, gear and rotary sensor, and is also waterproof. The electrically driven manipulator being used in the proposed actuator modules will be shown. Two modularized electrical actuator modules were developed for inspection, maintenance and decommission. Using the two developed actuator modules, the manipulator inspecting the welding area of reactor vessel is easily developed. Various modularized electrical actuator modules will be developed in terms of size and power.

Solar cell junction temperature measurement of PV module

KAUST Repository

Huang, B.J.; Yang, P.E.; Lin, Y.P.; Lin, B.Y.; Chen, H.J.; Lai, R.C.; Cheng, J.S.

2011-01-01

The present study develops a simple non-destructive method to measure the solar cell junction temperature of PV module. The PV module was put in the environmental chamber with precise temperature control to keep the solar PV module as well

Module and electronics developments for the ATLAS ITK pixel system

CERN Document Server

Munoz Sanchez, Francisca Javiela; The ATLAS collaboration

2017-01-01

The ATLAS experiment is preparing for an extensive modification of its detectors in the course of the planned HL-LHC accelerator upgrade around 2025. The ATLAS upgrade includes the replacement of the entire tracking system by an all-silicon detector (Inner Tracker, ITk). The five innermost layers of ITk will be a pixel detector built of new sensor and readout electronics technologies to improve the tracking performance and cope with the severe HL-LHC environment in terms of occupancy and radiation. The total area of the new pixel system could measure up to 14 m2, depending on the final layout choice, which is expected to take place in 2017. In this paper an overview of the ongoing R\\&D activities on modules and electronics for the ATLAS ITk is given including the main developments and achievements in silicon planar and 3D sensor technologies, readout and power challenges.

Automatic modulation recognition of communication signals

CERN Document Server

Azzouz, Elsayed Elsayed

1996-01-01

Automatic modulation recognition is a rapidly evolving area of signal analysis. In recent years, interest from the academic and military research institutes has focused around the research and development of modulation recognition algorithms. Any communication intelligence (COMINT) system comprises three main blocks: receiver front-end, modulation recogniser and output stage. Considerable work has been done in the area of receiver front-ends. The work at the output stage is concerned with information extraction, recording and exploitation and begins with signal demodulation, that requires accurate knowledge about the signal modulation type. There are, however, two main reasons for knowing the current modulation type of a signal; to preserve the signal information content and to decide upon the suitable counter action, such as jamming. Automatic Modulation Recognition of Communications Signals describes in depth this modulation recognition process. Drawing on several years of research, the authors provide a cr...

Design and development of CAMAC 12 bit ADC/DAC dual purpose module

International Nuclear Information System (INIS)

Kulkarni, S.G.; Gore, J.A.; Ramlal, V.; Matkar, U.V.; Lokare, R.N.; Yadav, M.L.; Ekambaram, M.; Gupta, A.K.; Datar, V.M.

2013-01-01

A dual function CAMAC module is designed for Pelletron Accelerator which can function as 12 bit 8 channels DAC or 12 bit 16 channels ADC. Spartan 2 series of FPGA is used for implementing the CAMAC interface logic as well as logic for ADC/DAC interface. The PCB has both the ADC and DAC mounted but the module can have only one function selected due to wiring constraint. Two different VHDL programs (one for the ADC and other for the DAC) reside on the EEPROM permitting selection of any one as per the functionality required. The module is working as a 12 bit DAC at BARC-TIFR Pelletron Linac Facility, successfully. (author)

Module for Interns in Medical Ethics: A Developmental Diegesis.

Science.gov (United States)

Mahajan, Rajiv; Goyal, Parmod Kumar; Sidhu, Tanvir Kaur; Kaur, Upinder; Kaur, Sandeep; Gupta, Vitull

2017-12-01

Media report is rife with incidences of doctor-patients' conflict, and this partly is due to communication gap and unethical practices being adopted by the doctors. Our regular curriculum fails to impart any training in ethical issues in patient care. Imparting training to students in these soft-skills is the need of the hour. To develop a module for interns in medical ethics (MIME) in patient care, validate it and pilot run the module for standardization. After conducting faculty development workshop in curriculum designing and three rounds of Delphi with alumni, a module in medical ethics was developed and peer validated. The questionnaire for pilot run, questionnaire for future use of module delivery and pre- and post-test were also peer validated. The module was delivered to 17 interns as pilot run in the form of 4 days' workshop. After pilot run, the module was standardized to 10 broad topics and 3 days' workshop. The questionnaire for future delivery of module in regular routine was also validated during pilot run. Twenty-five faculty members participated in 1 day faculty development workshop and 59 alumni completed three rounds of Delphi. After peer review by five experts, a module of 11 broad areas was developed and was pilot run on 17 interns. Based on the feedback from pilot run, a standardized, validated 18 h teaching MIME in patient care was developed. Pilot study proves that curriculum innovation in the form of medical ethics training to interns; when as undergraduate students, they actively participate in patient care under supervision will go a long way in inculcating soft skills like ethics, compassion and communication in them.

On staggered indecomposable Virasoro modules

International Nuclear Information System (INIS)

Kytoelae, Kalle; Ridout, David

2009-01-01

In this article, certain indecomposable Virasoro modules are studied. Specifically, the Virasoro mode L 0 is assumed to be nondiagonalizable, possessing Jordan blocks of rank 2. Moreover, the module is further assumed to have a highest weight submodule, the 'left module', and that the quotient by this submodule yields another highest weight module, the 'right module'. Such modules, which have been called staggered, have appeared repeatedly in the logarithmic conformal field theory literature, but their theory has not been explored in full generality. Here, such a theory is developed for the Virasoro algebra using rather elementary techniques. The focus centers on two different but related questions typically encountered in practical studies: How can one identify a given staggered module, and how can one demonstrate the existence of a proposed staggered module. Given just the values of the highest weights of the left and right modules, themselves subject to simple necessary conditions, invariants are defined which together with the knowledge of the left and right modules uniquely identify a staggered module. The possible values of these invariants form a vector space of dimension 0, 1, or 2, and the structures of the left and right modules limit the isomorphism classes of the corresponding staggered modules to an affine subspace (possibly empty). The number of invariants and affine restrictions is purely determined by the structures of the left and right modules. Moreover, in order to facilitate applications, the expressions for the invariants and restrictions are given by formulas as explicit as possible (they generally rely on expressions for Virasoro singular vectors). Finally, the text is liberally peppered throughout with examples illustrating the general concepts. These have been carefully chosen for their physical relevance or for the novel features they exhibit.

On staggered indecomposable Virasoro modules

Energy Technology Data Exchange (ETDEWEB)

Kytoelae, Kalle [Geneve Univ. (Switzerland); Ridout, David [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

2009-06-15

In this article, certain indecomposable Virasoro modules are studied. Specifically, the Virasoro mode L0 is assumed to be non-diagonalisable, possessing Jordan blocks of rank two. Moreover, the module is further assumed to have a highest weight submodule, the ''left module'', and that the quotient by this submodule yields another highest weight module, the ''right module''. Such modules, which have been called staggered, have appeared repeatedly in the logarithmic conformal field theory literature, but their theory has not been explored in full generality. Here, such a theory is developed for the Virasoro algebra using rather elementary techniques. The focus centres on two different but related questions typically encountered in practical studies: How can one identify a given staggered module, and how can one demonstrate the existence of a proposed staggered module. Given just the values of the highest weights of the left and right modules, themselves subject to simple necessary conditions, invariants are defined which together with the knowledge of the left and right modules uniquely identify a staggered module. The possible values of these invariants form a vector space of dimension zero, one or two, and the structures of the left and right modules limit the isomorphism classes of the corresponding staggered modules to an affine subspace (possibly empty). The number of invariants and affine restrictions is purely determined by the structures of the left and right modules. Moreover, in order to facilitate applications, the expressions for the invariants and restrictions are given by formulae as explicit as possible (they generally rely on expressions for Virasoro singular vectors). Finally, the text is liberally peppered throughout with examples illustrating the general concepts. These have been carefully chosen for their physical relevance or for the novel features they exhibit. (orig.)

On staggered indecomposable Virasoro modules

International Nuclear Information System (INIS)

Kytoelae, Kalle; Ridout, David

2009-06-01

In this article, certain indecomposable Virasoro modules are studied. Specifically, the Virasoro mode L0 is assumed to be non-diagonalisable, possessing Jordan blocks of rank two. Moreover, the module is further assumed to have a highest weight submodule, the ''left module'', and that the quotient by this submodule yields another highest weight module, the ''right module''. Such modules, which have been called staggered, have appeared repeatedly in the logarithmic conformal field theory literature, but their theory has not been explored in full generality. Here, such a theory is developed for the Virasoro algebra using rather elementary techniques. The focus centres on two different but related questions typically encountered in practical studies: How can one identify a given staggered module, and how can one demonstrate the existence of a proposed staggered module. Given just the values of the highest weights of the left and right modules, themselves subject to simple necessary conditions, invariants are defined which together with the knowledge of the left and right modules uniquely identify a staggered module. The possible values of these invariants form a vector space of dimension zero, one or two, and the structures of the left and right modules limit the isomorphism classes of the corresponding staggered modules to an affine subspace (possibly empty). The number of invariants and affine restrictions is purely determined by the structures of the left and right modules. Moreover, in order to facilitate applications, the expressions for the invariants and restrictions are given by formulae as explicit as possible (they generally rely on expressions for Virasoro singular vectors). Finally, the text is liberally peppered throughout with examples illustrating the general concepts. These have been carefully chosen for their physical relevance or for the novel features they exhibit. (orig.)

On staggered indecomposable Virasoro modules

Science.gov (United States)

Kytölä, Kalle; Ridout, David

2009-12-01

In this article, certain indecomposable Virasoro modules are studied. Specifically, the Virasoro mode L0 is assumed to be nondiagonalizable, possessing Jordan blocks of rank 2. Moreover, the module is further assumed to have a highest weight submodule, the "left module," and that the quotient by this submodule yields another highest weight module, the "right module." Such modules, which have been called staggered, have appeared repeatedly in the logarithmic conformal field theory literature, but their theory has not been explored in full generality. Here, such a theory is developed for the Virasoro algebra using rather elementary techniques. The focus centers on two different but related questions typically encountered in practical studies: How can one identify a given staggered module, and how can one demonstrate the existence of a proposed staggered module. Given just the values of the highest weights of the left and right modules, themselves subject to simple necessary conditions, invariants are defined which together with the knowledge of the left and right modules uniquely identify a staggered module. The possible values of these invariants form a vector space of dimension 0, 1, or 2, and the structures of the left and right modules limit the isomorphism classes of the corresponding staggered modules to an affine subspace (possibly empty). The number of invariants and affine restrictions is purely determined by the structures of the left and right modules. Moreover, in order to facilitate applications, the expressions for the invariants and restrictions are given by formulas as explicit as possible (they generally rely on expressions for Virasoro singular vectors). Finally, the text is liberally peppered throughout with examples illustrating the general concepts. These have been carefully chosen for their physical relevance or for the novel features they exhibit.

Development and testing of shingle-type solar cell modules. Quarterly report No. 2

Energy Technology Data Exchange (ETDEWEB)

Shepard, N.F.

1978-01-05

The details of a shingle module design which produces in excess of 97 watts/m/sup 2/ of module area at 1 kW/m/sup 2/ insolation and at 60/sup 0/C are reported. This selected design employs a tempered glass coverplate to provide the primary solar cell structural support. The use of the B.F. Goodrich FLEXSEAL roofing system as the outer skin of the shingle substrate provides a high confidence of achieving the 15 year service life goal. The fabrication and testing of a preproduction module of this design has demonstrated that this selected approach will meet the environmental testing requirements imposed by the contract. Attempts to fabricate a preproduction module of an alternative design, which embeds the solar cell assembly within a methyl methacrylate casting, proved unsuccessful.

Development of measurement device for evaluation of solar cell module output. 2; Taiyo denchi module shutsuryoku hyokayo sokuteiki no kaihatsu. 2

Energy Technology Data Exchange (ETDEWEB)

Minoda, M.; Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

1996-10-27

Enhancement in design efficiency may be attained as well as utilization in maintenance if on-the-spot data is made available, for the purpose of flexibly dealing with changes in design or matching with a house structure, in calculating the power generation output of a solar cell (PV) module. Under the circumstances, a small-sized compound measuring device was produced as a prototype which, using an I-V curve tracer, measured output and condition of a roof at the time of installation, compared with the optimum operation and predicted the power generation. The device was structured with the main body consisting of a computing part, measurement controller and power supply and with various sensor modules. The electron load control method was employed in order to measure I-V characteristics of the PV module, since it was desirable to use a variable load and to cover the range from the release voltage of a solar cell to the short-circuit state through the maximum output point. The reference module method was used for the system evaluation. The device was presumably applicable to a PV system design by incorporating a sensor module for measuring design environment data, which was essential at the time of a system design, in addition to those for measuring output. 9 refs., 4 figs., 3 tabs.

Development, Implementation, and Assessment of Climate Curricular Materials for Introductory Undergraduates: Lessons Learned from the InTeGrate Project's Climate of Change Module

Science.gov (United States)

Walker, B.; Fadem, C. M.; Shellito, L. J.

2014-12-01

Designing climate change curricular materials suitable for wide adoption across institutions and academic disciplines (including those outside of the geosciences) requires collaboration among faculty at different types of institutions and consideration of a variety of student populations, learning styles, and course formats. The Interdisciplinary Teaching of Geoscience for a Sustainable Future (InTeGrate) project, an NSF STEP Center program, provides opportunities for faculty to develop 2-3 week teaching modules to engage students in understanding the intersections between geoscience topics and societal issues. From 2012-2014, a team of 3 faculty from a liberal arts college, comprehensive university, and community college developed, implemented, assessed, and revised a 2-3 week module for introductory undergraduates entitled "Climate of change: interactions and feedbacks between water, air, and ice". The module uses authentic atmosphere, ocean, and cryosphere data from several regions to illustrate how climate impacts human societies and that the climate system has interacting components complicated by feedbacks, uncertainties, and human behavioral decisions. Students also consider past and present human adaptations to climate fluctuations. The module was piloted in introductory geology, meteorology, and oceanography courses during the 2012-2013 academic year, during which time formative and summative assessments were administered and used to modify the curricular materials. We will provide an overview of the module's content, instructional strategies involved in implementing the module, and methods of formative and summative assessment. We will also report on lessons learned during the development, piloting, revision, and publishing process, the importance of fostering partnerships between faculty from different institution types, and design approaches that promote widespread adoption of climate curricular materials.

Web-based Learning Modules using Research Data

Science.gov (United States)

Pilachowski, Catherine A.; Hamper, R.; Morris, F.

2011-01-01

Three web-based learning modules for introductory undergraduate astronomy courses are available at Indiana University Bloomington. The NovaSearch module allows students to view images of the core of the Andromeda Galaxy to discover novae and monitor their light curves. The Proper Pair module allows students to examine proper motion and parallax data from Hipparcos to determine if pairs of stars close together on the sky are true binary star systems. A third module, Astronomy in Color, allows students to produce color images using multi-wavelength data. The pedagogical goals of these curriculum materials are to teach that science is a process of discovery, not just a body of knowledge, to increase positive attitudes towards science by engaging students in discovery, and to motivate students towards pursuing STEM careers by giving students an opportunity to develop skills such as critical thinking, teamwork, and task focus that are important in any career path. The learning modules may be accessed at www.astro.indiana.edu/catyp/rbseu The development of these curriculum modules has been funded by the national Science Foundation through grant DUE-0618441.

Development of Bone-Conducted Ultrasonic Hearing Aid for the Profoundly Deaf: Assessments of the Modulation Type with Regard to Intelligibility and Sound Quality

Science.gov (United States)

Nakagawa, Seiji; Fujiyuki, Chika; Kagomiya, Takayuki

2012-07-01

Bone-conducted ultrasound (BCU) is perceived even by the profoundly sensorineural deaf. A novel hearing aid using the perception of amplitude-modulated BCU (BCU hearing aid: BCUHA) has been developed; however, further improvements are needed, especially in terms of articulation and sound quality. In this study, the intelligibility and sound quality of BCU speech with several types of amplitude modulation [double-sideband with transmitted carrier (DSB-TC), double-sideband with suppressed carrier (DSB-SC), and transposed modulation] were evaluated. The results showed that DSB-TC and transposed speech were more intelligible than DSB-SC speech, and transposed speech was closer than the other types of BCU speech to air-conducted speech in terms of sound quality. These results provide useful information for further development of the BCUHA.

Photovoltaic module and interlocked stack of photovoltaic modules

Science.gov (United States)

Wares, Brian S.

2014-09-02

One embodiment relates to an arrangement of photovoltaic modules configured for transportation. The arrangement includes a plurality of photovoltaic modules, each photovoltaic module including a frame. A plurality of individual male alignment features and a plurality of individual female alignment features are included on each frame. Adjacent photovoltaic modules are interlocked by multiple individual male alignment features on a first module of the adjacent photovoltaic modules fitting into and being surrounded by corresponding individual female alignment features on a second module of the adjacent photovoltaic modules. Other embodiments, features and aspects are also disclosed.

Student's Need Analysis for the Development of Chemistry Modules Based Guided Inquiry to Improve Science Process Skill

Directory of Open Access Journals (Sweden)

Jane Arantika

2018-04-01

Full Text Available Science process skills (SPS are an important aspect of learning science. SPS help students to develop creativity in learning. Process skills such as observing, formulating questions, interpreting, experimenting, hypothesizing, applying concepts, and communicating. This study aims to analyze the need for development resources needs of science filled with science process skills. Requirement analysis of the development of teaching materials with the skill of the process of science needs to be done because the textbook is the reference a teacher in the class. The subjects matter of chemistry the study was three senior high schools in Sambas, West Borneo. Needs analysis conducted using a qualitative approach, in terms of needs in classroom learning and content of process skills on teaching materials. Data were collected by interviews and questionnaires were analyzed descriptively. The results showed that as many as 27 percents of students perceive the book used in learning has not yet trained the science process skills. As many as 73 percents of students perceive that they need instructional materials in the form of inquiry-based chemistry modules to improve science process skills. Modules are developed based guided inquiry for having guided inquiry learning stages that can practice students' science process skills.

Overview of the TFTB lithium blanket module program

International Nuclear Information System (INIS)

Jassby, D.L.

1986-01-01

The Lithium Blanket Module (LBM) is an ∼ 80-cm 3 module, representative of a helium-cooled lithium oxide fusion reactor blanket module. This paper summarizes the design, development, and construction of the LBM, and indicates the present status of the LBM program

Overview of radar intra-pulse modulation recognition

Science.gov (United States)

Zang, Hanlin; Li, Yanling

2018-05-01

This paper introduces the current radar intra-pulse modulation method, describes the status quo and development direction of the intentional modulation and unintentional modulation in the pulse, and summarizes the existing problems and prospects for the future. Looking forward to the future, and providing a reference direction for the research on radar signal recognition in the next step.

Analyzing Thermal Module Developments and Trends in High-Power LED

Directory of Open Access Journals (Sweden)

Jung-Chang Wang

2014-01-01

Full Text Available The solid-state light emitting diode (SSLED has been verified as consumer-electronic products and attracts attention to indoor and outdoor lighting lamp, which has a great benefit in saving energy and environmental protection. However, LED junction temperature will influence the luminous efficiency, spectral color, life cycle, and stability. This study utilizes thermal performance experiments with the illumination-analysis method and window program (vapour chamber thermal module, VCTM V1.0 to investigate and analyze the high-power LED (Hi-LED lighting thermal module, in order to achieve the best solution of the fin parameters under the natural convection. The computing core of the VCTM program employs the theoretical thermal resistance analytical approach with iterative convergence stated in this study to obtain a numerical solution. Results showed that the best geometry of thermal module is 4.4 mm fin thickness, 9.4 mm fin pitch, and 37 mm fin height with the LED junction temperature of 58.8°C. And the experimental thermal resistances are in good agreement with the theoretical thermal resistances; calculating error between measured data and simulation results is no more than ±7%. Thus, the Hi-LED illumination lamp has high life cycle and reliability.

Prinsip-Prinsip Dasar Pengembangan Modul Berpendekatan Hypercontent

Directory of Open Access Journals (Sweden)

Dewi Salma Prawiradilaga

2018-01-01

Full Text Available Artikel ini menguraikan prinsip-prinsip dasar pengembangan modul dengan pendekatan hypercontent. Berbeda dengan modul konvensional yang berlogika linier, prosedural, dan relatif kaku, modul berpendekatan hypercontent didesain menggunakan logika postmodern yang relatif non-linier, acak, dan fleksibel. Dengan demikian desain modul berpendekatan hypercontent memberikan kesempatan bagi penggunanya untuk mempelajari dari sisi mana saja sesuai kebutuhan belajar. Tidak diharuskan memulai dari materi yang berada pada urutan pertama. Pendekatan hypercontent mengarahkan desain modul diperkaya oleh sumber-sumber belajar di dunia maya. Caranya dengan membuat tautan ke laman website, saluran YouTube, dan lainnya melalui URL, QR code dan sejenisnya. Pendekatan hypercontent dipadukan dengan pendekatan technological, pedagogical, content-knowledge menjadikan substansi modul yang dikembangkan lengkap dilihat dari sisi kesesuaian dan kekayaan materi serta kesesuaian pendekatan pedagogiknya. This article describes the basic foundations of the module development using hypercontent approach. Different from the conventional one wich is more linier, procedural, and rigid, hypercontent approach module are developed under postmodern logic of thinking which is more non-linear, non-sequential, and flexible. Thus, hypercontent modul open an opportunity for the student to use it in non-sequential and non-procedural ways according to their own learning need wich are different from one another. In this case there is no obligation to start the learning process from the first chapter. Hypercontent module approach also enriched its content by lots of learning resources from the internet by creating linkages to several appropriates webpages, YouTube channels, and others via URL, QR code and etc. Hypercontent approach combined with technological, pedagogical, content-knowledge approach make the substance of the modul more complete in terms of its pedagogical appropriateness and

Modulation of gene expression made easy

DEFF Research Database (Denmark)

Solem, Christian; Jensen, Peter Ruhdal

2002-01-01

A new approach for modulating gene expression, based on randomization of promoter (spacer) sequences, was developed. The method was applied to chromosomal genes in Lactococcus lactis and shown to generate libraries of clones with broad ranges of expression levels of target genes. In one example...... that the method can be applied to modulating the expression of native genes on the chromosome. We constructed a series of strains in which the expression of the las operon, containing the genes pfk, pyk, and ldh, was modulated by integrating a truncated copy of the pfk gene. Importantly, the modulation affected...

Weyl modules, demazure modules, KR-modules, crystals, fusion products and limit constructions

OpenAIRE

Fourier, G.; Littelmann, P.

2007-01-01

We study finite dimensional representations of current algebras, loop algebras and their quantized versions. For the current algebra of a simple Lie algebra of type {\\tt ADE}, we show that Kirillov-Reshetikhin modules and Weyl modules are in fact all Demazure modules. As a consequence one obtains an elementary proof of the dimension formula for Weyl modules for the current and the loop algebra. Further, we show that the crystals of the Weyl and the Demazure module are the same up to some addi...

Development of a Respiratory Inductive Plethysmography Module Supporting Multiple Sensors for Wearable Systems

Directory of Open Access Journals (Sweden)

Zhengbo Zhang

2012-09-01

Full Text Available In this paper, we present an RIP module with the features of supporting multiple inductive sensors, no variable frequency LC oscillator, low power consumption, and automatic gain adjustment for each channel. Based on the method of inductance measurement without using a variable frequency LC oscillator, we further integrate pulse amplitude modulation and time division multiplexing scheme into a module to support multiple RIP sensors. All inductive sensors are excited by a high-frequency electric current periodically and momentarily, and the inductance of each sensor is measured during the time when the electric current is fed to it. To improve the amplitude response of the RIP sensors, we optimize the sensing unit with a matching capacitor parallel with each RIP sensor forming a frequency selection filter. Performance tests on the linearity of the output with cross-sectional area and the accuracy of respiratory volume estimation demonstrate good linearity and accurate lung volume estimation. Power consumption of this new RIP module with two sensors is very low. The performance of respiration measurement during movement is also evaluated. This RIP module is especially desirable for wearable systems with multiple RIP sensors for long-term respiration monitoring.

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of CIS solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihtsu (CIS taiyo denchi module no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been performed on a technology to manufacture CIS-based thin film solar cells. This paper summarizes the achievements in fiscal 1999. In the research of a large-area light absorbing layer manufacturing technology, investigation was made on light absorbing layers in manufacturing sub-modules with a size of 30 cm times 30 cm. With regard to the temperature condition in the light absorbing layer forming process, it was found that the cooling rate affects particularly the adhesion in the connecting interface of the light absorbing layer and the Mo rear electrode layer. In addition, it was revealed that the sulfur take-in amount can be increases by extending the retention time at the sulfurizing temperature and by decreasing the temperature to turn the gas phase into selenium. In the research of elementary technologies to establish the mass production process, developments were performed on the high-resistance buffer layer manufacturing technology, the high-quality window layer film manufacturing technology, and the technology to manufacture rear electrode layer made of high-quality metals. In developing the patterning technology, two kinds of the existing patterning devices were modified and adjusted for patterning the substrates with a size of 30 cm times 30 cm. In addition, a processing device was installed in the conventional manually operated process for module finishing. (NEDO)

Dynamic simulator for nuclear power plants (DSNP): development, verification, and expansion of modules

International Nuclear Information System (INIS)

Larson, H.A.; Dean, E.M.; Koenig, J.F.; Gale, J.G.; Lehto, W.K.

1984-01-01

The DSNP Simulation Language facilitates whole reactor plant simulation and design. Verification includes DSNP dynamic modeling of Experimental Breeder Reactor No. 2 (EBR-II) plant experiments as well as comparisons with verified simulation programs. Great flexibility is allowed in expanding the DSNP language and accommodate other computer languages. The component modules of DSNP, contained in libraries, are continually updated with new, improved, and verified modules. The modules are used to simulate the dynamic response of LMFBR reactor systems to upset and transient conditions, with special emphasis on investigations of inherent shutdown mechanisms

Research: Designing interprofessional modules for undergraduate ...

African Journals Online (AJOL)

... financial constraints, administrative support, logistical issues and resistance to change. The designing and implementing of new modules were intense and time consuming, and required commitment. The development of the modules was an excellent example of interprofessional teamwork that needs to be transferred to ...

Development of a new lower hybrid antenna module using a poloidal power divider

International Nuclear Information System (INIS)

Maebara, S.; Imai, T.; Seki, M.; Suganuma, K.; Goniche, M.; Bibet, Ph.; Berio, S.; Brossaud, J.; Rey, G.; Tonon, G.

1997-03-01

A realistic antenna module using a poloidal divider for lower hybrid current drive (LHCD) experiment, is modelled and fabricated. In this antenna module test II, three types of poloidal dividers, which split the power in 3, are tested. (author)

Superstability for Generalized Module Left Derivations and Generalized Module Derivations on a Banach Module (I

Directory of Open Access Journals (Sweden)

Rassias JM

2009-01-01

Full Text Available We discuss the superstability of generalized module left derivations and generalized module derivations on a Banach module. Let be a Banach algebra and a Banach -module, and . The mappings , and are defined and it is proved that if (resp., is dominated by then is a generalized (resp., linear module- left derivation and is a (resp., linear module- left derivation. It is also shown that if (resp., is dominated by then is a generalized (resp., linear module- derivation and is a (resp., linear module- derivation.

ATLAS SCT - Progress on the Silicon Modules

CERN Multimedia

Tyndel, M.

The ATLAS SCT consists of 4088 silicon modules. Each module is made up of 4 silicon sensors with 1536 readout strips. Individual strips are connected to FE amplifiers, discriminators and pipelines on the module, i.e. there are 12 radiation hard ASICs, each containing 128 channels on the module. The sensors and the ASICs were developed for the ATLAS experiment and production is proceeding smoothly with over half the components delivered. The components of a module - 4 silicon sensors, a Cu/polyimide hybrid and pitch adaptor, and 12 ASICs - need to be carefully and precisely assembled onto a carbon and ceramic framework, which supports the module and removes the heat. Eleven production clusters are preparing to carry this out over the next two years. An important milestone for the barrel modules has been passed with the first cluster (KEK) now in production (~40 modules produced). A second cluster UK-B has qualified by producing five modules within specification (see below) and is about to start production. T...

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, development of technologies to manufacture next-generation thin film solar cells (development of technologies to manufacture CIS solar cell modules); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (CIS taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development was made with an objective to achieve conversion efficiency of 13% in a 30 cm times 30 cm size submodule of a CIS-based thin film solar cell, and to develop a manufacturing technology that can achieve 140 yen/Wp. This paper describes the achievements attained during fiscal 1997. In fiscal 1997, based on the achievements reached during the previous year, a submodule with a size of 10 cm times 30 cm was fabricated for an attempt of improving the open voltage and short circuit current density. Simultaneously, the applicability thereof to a module with an area as large as 30 cm times 30 cm was evaluated. As a result of experimental discussions, enhancement in the open voltage was verified by increasing amount of Ga or sulfur, but it was not possible to achieve 600 mV or higher. In the research of component technologies to establish a mass production process, research and development was made on a high-resistance buffer layer film forming technology, a high-quality window layer film forming technology, a high-quality metallic rear electrode film forming technology, and patterning technologies. The outdoor exposure test was continued on laminated mini-modules with a size of 10 cm times 10 cm. (NEDO)

A Learning Module for BA Students to Develop ICT Skills for their Learning Activities | Un module de formation visant le développement des compétences TICE chez les étudiants en baccalauréat

Directory of Open Access Journals (Sweden)

Hervé Platteaux

2015-11-01

Full Text Available This case illustrates the process of developing a learning module to support BA students in their use of ICT (Information and Communication Technology tools in their learning. At the university where this case occurred, the skill level of ICT use among students in a learning context was very heterogeneous. The E-learning Competency Centre, or ECC, which was in charge of techno-pedagogical development at the institution, created a hybrid learning module that offered students learning materials and activities with both face-to-face workshops and online tutorials for autonomous learning. The students were able to choose subjects they wanted to learn "à la carte" by taking tutorials on their own and/or by participating in face-to-face workshops. The module described in this case is currently under construction. The design phase of this project is the focus of this case study.

Development of a Smart Mobile Data Module for Fetal Monitoring in E-Healthcare.

Science.gov (United States)

Houzé de l'Aulnoit, Agathe; Boudet, Samuel; Génin, Michaël; Gautier, Pierre-François; Schiro, Jessica; Houzé de l'Aulnoit, Denis; Beuscart, Régis

2018-03-23

The fetal heart rate (FHR) is a marker of fetal well-being in utero (when monitoring maternal and/or fetal pathologies) and during labor. Here, we developed a smart mobile data module for the remote acquisition and transmission (via a Wi-Fi or 4G connection) of FHR recordings, together with a web-based viewer for displaying the FHR datasets on a computer, smartphone or tablet. In order to define the features required by users, we modelled the fetal monitoring procedure (in home and hospital settings) via semi-structured interviews with midwives and obstetricians. Using this information, we developed a mobile data transfer module based on a Raspberry Pi. When connected to a standalone fetal monitor, the module acquires the FHR signal and sends it (via a Wi-Fi or a 3G/4G mobile internet connection) to a secure server within our hospital information system. The archived, digitized signal data are linked to the patient's electronic medical records. An HTML5/JavaScript web viewer converts the digitized FHR data into easily readable and interpretable graphs for viewing on a computer (running Windows, Linux or MacOS) or a mobile device (running Android, iOS or Windows Phone OS). The data can be viewed in real time or offline. The application includes tools required for correct interpretation of the data (signal loss calculation, scale adjustment, and precise measurements of the signal's characteristics). We performed a proof-of-concept case study of the transmission, reception and visualization of FHR data for a pregnant woman at 30 weeks of amenorrhea. She was hospitalized in the pregnancy assessment unit and FHR data were acquired three times a day with a Philips Avalon® FM30 fetal monitor. The prototype (Raspberry Pi) was connected to the fetal monitor's RS232 port. The emission and reception of prerecorded signals were tested and the web server correctly received the signals, and the FHR recording was visualized in real time on a computer, a tablet and smartphones

SLAC FASTBUS Snoop Module: test results and support software

International Nuclear Information System (INIS)

Gustavson, D.B.; Walz, H.V.

1985-09-01

The development of a diagnostic module for FASTBUS has been completed. The Snoop Module is designed to reside on a Crate Segment and provide high-speed diagnostic monitoring and testing capabilities. Final hardware details and testing of production prototype modules are reported. Features of software under development for a stand-alone single Snoop diagnostic system and Multi-Snoop networks will be discussed. 3 refs., 2 figs

Designing interprofessional modules for undergraduate healthcare learners

Directory of Open Access Journals (Sweden)

C Maree

2017-12-01

Full Text Available Background. Interprofessional education aims to prepare learners to collaborate across specialties to provide high-quality healthcare. Internationally and nationally, the emerging need for integrated healthcare and education has been emphasised. The current education programme at the School of Health Care Sciences, University of Pretoria, South Africa primarily follows a uniprofessional approach.Objectives. To describe the development of interprofessional modules over 4 years between the departments of Human Nutrition, Nursing Science, Occupational Therapy, Physiotherapy and Radiography.Methods. The Knowledge-to-Action model guided the module development process. The planning phase comprised three steps: (i problem identification (e.g. national and international policy focus on interprofessional education; (ii review of existing knowledge (e.g. common learning outcomes; and (iii adaptation of knowledge to the local context (e.g. syllabi and logistics.Results. The development of interprofessional modules can be guided by the above-mentioned model to meet the needs of the faculty, departments, students and community and to contribute to interprofessional education, while overcoming the associated challenges.Conclusion. Challenges included clashes in timetable schedules, financial constraints, administrative support, logistical issues and resistance to change. The designing and implementing of new modules were intense and time consuming, and required commitment. The development of the modules was an excellent example of interprofessional teamwork that needs to be transferred to the implementation and role modelling of interprofessional education.

An online module series to prepare pharmacists to facilitate student engagement in patient-centered care delivery: development and evaluation