WorldWideScience

Sample records for motor truck engineering

  1. 75 FR 43975 - California State Motor Vehicle and Nonroad Engine Pollution Control Standards; Truck Idling...

    Science.gov (United States)

    2010-07-27

    ... standards) for the control of emissions from new motor vehicles or new motor vehicle engines prior to March... approval relating to the control of emissions from any new motor vehicle or new motor vehicle engine as... relating to the control of emissions from new nonroad spark-ignition engines smaller than 50 horsepower...

  2. Heavy Truck Engine Program

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Christopher

    2009-01-08

    The Heavy Duty Truck Engine Program at Cummins embodied three significant development phases. All phases of work strove to demonstrate a high level of diesel engine efficiency in the face of increasingly stringent emission requirements. Concurrently, aftertreatment system development and refinement was pursued in support of these efficiency demonstrations. The program's first phase focused on the demonstration in-vehicle of a high level of heavy duty diesel engine efficiency (45% Brake Thermal Efficiency) at a typical cruise condition while achieving composite emissions results which met the 2004 U.S. EPA legislated standards. With a combination of engine combustion calibration tuning and the development and application of Urea-based SCR and particulate aftertreatment, these demonstrations were successfully performed by Q4 of 2002. The second phase of the program directed efforts towards an in-vehicle demonstration of an engine system capable of meeting 2007 U.S. EPA legislated emissions requirements while achieving 45% Brake Thermal Efficiency at cruise conditions. Through further combustion optimization, the refinement of Cummins Cooled EGR architecture, the application of a high pressure common rail fuel system and the incorporation of optimized engine parasitics, Cummins Inc. successfully demonstrated these deliverables in Q2 of 2004. The program's final phase set a stretch goal of demonstrating 50% Brake Thermal Efficiency from a heavy duty diesel engine system capable of meeting 2010 U.S. EPA legislated emissions requirements. Cummins chose to pursue this goal through further combustion development and refinement of the Cooled EGR system architecture and also applied a Rankine cycle Waste Heat Recovery technique to convert otherwise wasted thermal energy to useful power. The engine and heat recovery system was demonstrated to achieve 50% Brake Thermal Efficiency while operating at a torque peak condition in second quarter, 2006. The 50% efficient

  3. 77 FR 9239 - California State Motor Vehicle and Nonroad Engine Pollution Control Standards; Truck Idling...

    Science.gov (United States)

    2012-02-16

    ... routed into the truck's exhaust system and PM trap; (b) a level 3 verified PM control strategy; or (c) use of other procedures to demonstrate an equivalent level of emissions compliance. B. Clean Air Act... passes the threshold test of materiality and * * * thereafter assess such material evidence against a...

  4. Diesel Engine Light Truck Application

    Energy Technology Data Exchange (ETDEWEB)

    None

    2007-12-31

    The Diesel Engine Light Truck Application (DELTA) program consists of two major contracts with the Department of Energy (DOE). The first one under DE-FC05-97-OR22606, starting from 1997, was completed in 2001, and consequently, a final report was submitted to DOE in 2003. The second part of the contract was under DE-FC05-02OR22909, covering the program progress from 2002 to 2007. This report is the final report of the second part of the program under contract DE-FC05-02OR22909. During the course of this contract, the program work scope and objectives were significantly changed. From 2002 to 2004, the DELTA program continued working on light-duty engine development with the 4.0L V6 DELTA engine, following the accomplishments made from the first part of the program under DE-FC05-97-OR22606. The program work scope in 2005-2007 was changed to the Diesel Particulate Filter (DPF) soot layer characterization and substrate material assessment. This final report will cover two major technical tasks. (1) Continuation of the DELTA engine development to demonstrate production-viable diesel engine technologies and to demonstrate emissions compliance with significant fuel economy advantages, covering progress made from 2002 to 2004. (2) DPF soot layer characterization and substrate material assessment from 2005-2007.

  5. Cummins Light Truck Diesel Engine Progress Report

    International Nuclear Information System (INIS)

    John H. Stang

    2000-01-01

    The Automotive Market in the United States is moving in the direction of more Light Trucks and fewer Small Cars. The customers for these vehicles have not changed, only their purchase decisions. Cummins has studied the requirements of this emerging market. Design and development of an engine system that will meet these customer needs has started. The engine system is a difficult one, since the combined requirements of a very fuel-efficient commercial diesel, and the performance and sociability requirements of a gasoline engine are needed. Results of early testing are presented which show that the diesel is possibly a good solution

  6. 75 FR 3252 - Ford Motor Company, Dearborn Truck Plant, Dearborn, MI; Notice of Negative Determination on...

    Science.gov (United States)

    2010-01-20

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-70,326] Ford Motor Company... workers and former workers of Ford Motor Company, Dearborn Truck Plant, Dearborn, Michigan. The Department... separations were not related to an increase in imports of like or directly competitive products with Ford F...

  7. Detroit Diesel Engine Technology for Light Duty Truck Applications - DELTA Engine Update

    Energy Technology Data Exchange (ETDEWEB)

    Freese, Charlie

    2000-08-20

    The early generation of the DELTA engine has been thoroughly tested and characterized in the virtual lab, during engine dynamometer testing, and on light duty trucks for personal transportation. This paper provides an up-to-date account of program findings. Further, the next generation engine design and future program plans will be briefly presented.

  8. Honda Motor Company's CVCC Engine

    Science.gov (United States)

    1980-01-01

    From 1968 to 1972, Honda Motor Co. of Japan designed, tested, and massproduced a stratified charge engine, the CVCC, which was lower in carbon monoxide, hydrocarbon, and nitrogen oxide emissions and higher in fuel economy than contemporary convention...

  9. 75 FR 38168 - Federal Motor Vehicle Theft Prevention Standard; Final Listing of 2011 Light Duty Truck Lines...

    Science.gov (United States)

    2010-07-01

    ... Theft Prevention Standard; Final Listing of 2011 Light Duty Truck Lines Subject to the Requirements of... light-duty truck lines subject to the requirements of the Federal motor vehicle theft prevention... exemption from the parts marking requirements of the Theft Prevention Standard for the Jaguar XJ vehicle...

  10. Clean Diesel Engine Component Improvement Program Diesel Truck Thermoelectric Generator

    Energy Technology Data Exchange (ETDEWEB)

    Elsner, N. B. [Hi-Z Technology, Inc., San Diego, CA (United States); Bass, J. C. [Hi-Z Technology, Inc., San Diego, CA (United States); Ghamaty, S. [Hi-Z Technology, Inc., San Diego, CA (United States); Krommenhoek, D. [Hi-Z Technology, Inc., San Diego, CA (United States); Kushch, A. [Hi-Z Technology, Inc., San Diego, CA (United States); Snowden, D. [Hi-Z Technology, Inc., San Diego, CA (United States); Marchetti, S. [Hi-Z Technology, Inc., San Diego, CA (United States)

    2005-03-16

    Hi-Z Technology, Inc. (Hi-Z) is currently developing four different auxiliary generator designs that are used to convert a portion (5 to 20%) of the waste heat from vehicle engines exhaust directly to electricity. The four designs range from 200 Watts to 10 kW. The furthest along is the 1 kW Diesel Truck Thermoelectric Generator (DTTEG) for heavy duty Class 8 Diesel trucks, which, under this program, has been subjected to 543,000 equivalent miles of bouncing and jarring on PACCAR's test track. Test experience on an earlier version of the DTTEG on the same track showed the need for design modifications incorporated in DTTEG Mod 2, such as a heavy duty shock mounting system and reinforcement of the electrical leads mounting system, the thermocouple mounting system and the thermoelectric module restraints. The conclusion of the 543,000 mile test also pointed the way for an upgrading to heavy duty hose or flex connections for the internal coolant connections for the TEG, and consideration of a separate lower temperature cooling loop with its own radiator. Fuel savings of up to $750 per year and a three to five year payback are believed to be possible with the 5 % efficiency modules. The economics are expected to improve considerably to approach a two year payback when the 5 kW to 10 kW generators make it to the market in a few years with a higher efficiency (20%) thermoelectric module system called Quantum Wells, which are currently under development by Hi-Z. Ultimately, as automation takes over to reduce material and labor costs in the high volume production of QW modules, a one year payback for the 5 kW to10 kW generator appears possible. This was one of the stated goals at the beginning of the project. At some future point in time, with the DTTEG becoming standard equipment on all trucks and automobiles, fuel savings from the 25% conversion of exhaust heat to useable electricity nationwide equates to a 10% reduction in the 12 to 15 million barrels per day of

  11. Engineering Task Plan for Water Supply for Spray Washers on the Support Trucks

    International Nuclear Information System (INIS)

    BOGER, R.M.

    2000-01-01

    This Engineering Task Plan (ETP) defines the task and deliverables associated with the design, fabrication and testing of an improved spray wash system for the Rotary Mode Core Sampling (RMCS) System Support Trucks

  12. Development of Diesel Engine Operated Forklift Truck for Explosive Gas Atmospheres

    Science.gov (United States)

    Vishwakarma, Rajendra Kumar; Singh, Arvind Kumar; Ahirwal, Bhagirath; Sinha, Amalendu

    2018-02-01

    For the present study, a prototype diesel engine operated Forklift truck of 2 t capacity is developed for explosive gas atmosphere. The parts of the Forklift truck are assessed against risk of ignition of the explosive gases, vapors or mist grouped in Gr. IIA and having ignition temperature more than 200°C. Identification of possible sources of ignition and their control or prevention is the main objective of this work. The design transformation of a standard Forklift truck into a special Forklift truck is made on prototype basis. The safety parameters of the improved Forklift truck are discussed in this paper. The specially designed Forklift truck is useful in industries where explosive atmospheres may present during normal working conditions and risk of explosion is a concern during handling or transportation of materials. This indigenous diesel engine based Forklift truck for explosive gas atmosphere classified as Zone 1 and Zone 2 area and gas group IIA is developed first time in India in association with the Industry.

  13. CAFE compliance by light trucks: economic impacts of clean diesel engine

    International Nuclear Information System (INIS)

    Teotia, A.; Vyas, A.; Cuenca, R.; Stodolsky, F.

    1999-01-01

    With the popularity of light trucks increasing in the United States, their share of the US light vehicle market had doubled between 1980 and 1996, climbing from 20 to 40%. By 1996, annual energy consumption for light trucks had risen to 5.97 x 10 15 Btu [5.97 quadrillion Btu, or ''quad'', or 6.30 x 10 18 joule (J)], compared to 7.94 quad (8.38 x 10 18 J) for cars. In recent years (since 1995), the fuel economy of US-manufactured light trucks (almost 99% of which use gasoline engines) has been below the Corporate Average Fuel Economy (CAFE) standards. This paper analyzes a strategy to reduce the CAFE shortfalls by adopting the new, highly energy-efficient clean diesel engine. Research on such engines has been funded by the US Department of Energy, Office of Heavy Vehicle Technologies, under its Light Truck Clean Diesel Engine Program. A clean diesel engine market penetration trajectory is developed, representing an industry response to meet the CAFE standards. Whether the engine will be produced inside the country or imported remains uncertain, so two cases are defined. Values of exports/imports of clean diesel engines/trucks under these cases are estimated. The macroeconomic benefits are estimated by using a model of the US economy developed by Standard and Poor's Data Resources, Inc. On the basis of gains in the gross domestic product projected under the alternative cases, domestic production of the clean diesel engine is favored over importing it. (author)

  14. Engineering task plan for the development, fabrication and installation of rotary mode core sample truck bellows

    International Nuclear Information System (INIS)

    BOGER, R.M.

    1999-01-01

    The Rotary Mode Core Sampling Trucks (RMSCTs) currently use a multi-sectioned bellows between the grapple box and the quill rod to compensate for drill head motion and to provide a path for purge gas. The current bellows, which is detailed on drawing H-2-690059, is expensive to procure, has a lengthy procurement cycle, and is prone to failure. Therefore, a task has been identified to design, fabricate, and install a replacement bellows. This Engineering Task Plan (ETP) is the management plan document for accomplishing the identified tasks. Any changes in scope of the ETP shall require formal direction by the Characterization Engineering manager. This document shall also be considered the work planning document for developmental control per Development Control Requirements (HNF 1999a). This Engineering Task Plan (ETP) is the management plan document for accomplishing the design, fabrication, and installation of a replacement bellows assembly for the Rotary Mode Core Sampling Trucks 3 and 4 (RMCST)

  15. Lift truck safety review

    International Nuclear Information System (INIS)

    Cadwallader, L.C.

    1997-03-01

    This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter's Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given

  16. Lift truck safety review

    Energy Technology Data Exchange (ETDEWEB)

    Cadwallader, L.C.

    1997-03-01

    This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter`s Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given.

  17. MODELING OF DYNAMIC PROCESSES IN PLANETARY IN-WHEEL MOTOR GEARBOXES OF MINE TRUCKS DURING ITS STARTING AND ACCELERATION

    Directory of Open Access Journals (Sweden)

    V. V. Mikhailov

    2012-01-01

    Full Text Available The paper describes a mathematical model for planetary double-row in-wheel motor gear box. Main parameters of its dynamic system have been determined in the paper. The paper reveals simulation of transition processes during starting and acceleration of a mine truck with electric motor wheels. Its own gear box frequency has been established theoretically and experimentally in the paper. The paper proposes an algorithm and program for calculations as an alternative to high-cost tests while investigating gear mechanism dynamics of large-size planetary gearboxes.

  18. Human factors engineering applications in the testing of the legal weight truck cask transportation system

    International Nuclear Information System (INIS)

    Smith, T.C.; Peck, M. III; Sealock, R.A.

    1994-01-01

    The Department of Energy's Office of Civilian Radioactive Waste Management (OCRWM) will collect performance data to be used in limited human factors engineering analysis of the light weight tractor as a component of the legal weight truck cask transport system. The Management and Operating contractor will provide an analysis and comparison of limited data on driver behavior and subjective driver evaluations of the light weight tractor performance versus that of a heavier baseline tractor. A significant difference in performance data would suggest that given tractor configurations affect driver behavior differently

  19. Final Rule for Control of Air Pollution From New Motor Vehicles and New Motor Vehicle Engines: Evaporative and Refueling Emission Regulations for Gasolineand Methanol-Fueled Light-Duty Vehicles and Light-Duty Trucks and Heavy-Duty Vehicles; Technical Amen

    Science.gov (United States)

    On March 24, 1993 EPA finalized a new test procedure to measure evaporative emissions from motor vehicles. The amendments modify several of the test procedure’s tolerances, equipment specifications, and procedural steps.

  20. Ride comfort optimization of a multi-axle heavy motorized wheel dump truck based on virtual and real prototype experiment integrated Kriging model

    Directory of Open Access Journals (Sweden)

    Bian Gong

    2015-06-01

    Full Text Available The optimization of hydro-pneumatic suspension parameters of a multi-axle heavy motorized wheel dump truck is carried out based on virtual and real prototype experiment integrated Kriging model in this article. The root mean square of vertical vibration acceleration, in the center of sprung mass, is assigned as the optimization objective. The constraints are the natural frequency, the working stroke, and the dynamic load of wheels. The suspension structure for the truck is the adjustable hydro-pneumatic suspension with ideal vehicle nonlinear characteristics, integrated with elastic and damping elements. Also, the hydraulic systems of two adjacent hydro-pneumatic suspension are interconnected. Considering the high complexity of the engineering model, a novel kind of meta-model called virtual and real prototype experiment integrated Kriging is proposed in this article. The interpolation principle and the construction of virtual and real prototype experiment integrated Kriging model were elucidated. Being different from traditional Kriging, virtual and real prototype experiment integrated Kriging combines the respective advantages of actual test and Computer Aided Engineering simulation. Based on the virtual and real prototype experiment integrated Kriging model, the optimization results, obtained by experimental verification, showed significant improvement in the ride comfort by 12.48% for front suspension and 11.79% for rear suspension. Compared with traditional Kriging, the optimization effect was improved by 3.05% and 3.38% respectively. Virtual and real prototype experiment integrated Kriging provides an effective way to approach the optimal solution for the optimization of high-complexity engineering problems.

  1. The Detroit Diesel DELTA Engine for Light Trucks and SUVs - Year 2000 Update

    Energy Technology Data Exchange (ETDEWEB)

    Nabil S. Hakim; Charles E. Freese; Stanley P. Miller

    2000-06-19

    Detroit Diesel Corporation (DDC) is developing the DELTA 4.0L V6 engine, specifically for the North American light truck market. This market poses unique requirements for a diesel engine, necessitating a clean sheet engine design. DELTA was developed from a clean sheet of paper, with the first engine firing just 228 days later. The process began with a Quality Function Deployment (QFD) analysis, which prioritized the development criteria. The development process integrated a co-located, fully cross-functional team. Suppliers were fully integrated and maintained on-site representation. The first demonstration vehicle moved under its own power 12 weeks after the first engine fired. It was demonstrated to the automotive press 18 days later. DELTA has repeatedly demonstrated its ability to disprove historical North American diesel perceptions and compete directly with gasoline engines. This paper outlines the Generation 0.0 development process and briefly defines the engine. A brief indication of the Generation 0.5 development status is given.

  2. The Detroit Diesel DELTA Engine for Light Trucks and SUVs - Year 2000 Update

    International Nuclear Information System (INIS)

    Nabil S. Hakim; Charles E. Freese; Stanley P. Miller

    2000-01-01

    Detroit Diesel Corporation (DDC) is developing the DELTA 4.0L V6 engine, specifically for the North American light truck market. This market poses unique requirements for a diesel engine, necessitating a clean sheet engine design. DELTA was developed from a clean sheet of paper, with the first engine firing just 228 days later. The process began with a Quality Function Deployment (QFD) analysis, which prioritized the development criteria. The development process integrated a co-located, fully cross-functional team. Suppliers were fully integrated and maintained on-site representation. The first demonstration vehicle moved under its own power 12 weeks after the first engine fired. It was demonstrated to the automotive press 18 days later. DELTA has repeatedly demonstrated its ability to disprove historical North American diesel perceptions and compete directly with gasoline engines. This paper outlines the Generation 0.0 development process and briefly defines the engine. A brief indication of the Generation 0.5 development status is given

  3. Simulations of Multi Combustion Modes Hydrogen Engines for Heavy Duty Trucks

    Directory of Open Access Journals (Sweden)

    Alberto A. Boretti

    2012-01-01

    Full Text Available The paper presents the numerical study of a diesel direct injection heavy duty truck engine converted to hydrogen. The engine has a power turbine connected through a clutch and a continuously variable transmission to the crankshaft. The power turbine may be disconnected and by-passed when it is inefficient or inconvenient to use. The conversion is obtained by replacing the Diesel injector with a hydrogen injector and the glow plug with a jet ignition device. The hydrogen engine operates different modes of combustion depending on the relative phasing of the main injection and the jet ignition. The engine generally operates mostly in Diesel-like mode, with the most part of the main injection following the suitable creation in cylinder conditions by jet ignition. For medium-low loads, better efficienciy is obtained with the gasoline-like mode jet igniting the premixed homogeneous mixture at top dead centre. It’s permitted at higher loads or at very low loads for the excessive peak pressure or the mixture too lean to burn rapidly. The hydrogen engine has better efficiency than Diesel outputs and fuel conversion. Thanks to the larger rate of heat release, it has the opportunity to run closer to stoichiometry and the multi mode capabilities. The critical area for this engine development is found in the design of a hydrogen injector delivering the amount of fuel needed to the large volume cylinder within a Diesel-like injection time.

  4. 40 CFR Appendix X to Part 86 - Sampling Plans for Selective Enforcement Auditing of Heavy-Duty Engines and Light-Duty Trucks

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Sampling Plans for Selective Enforcement Auditing of Heavy-Duty Engines and Light-Duty Trucks X Appendix X to Part 86 Protection of... Plans for Selective Enforcement Auditing of Heavy-Duty Engines and Light-Duty Trucks Table 1—Sampling...

  5. Development of the New Light-Duty Hybrid Truck

    OpenAIRE

    Yamaguchi, Koichi

    2008-01-01

    Hino Motors, Ltd., developed the new light-duty hybrid truck whose traction motor, inverter, and traction battery were completely redesigned for maximizing output and efficiency. It also succeeds in balancing low fuel economy and low exhaust emissions by utilizing a combination of a new hybrid system control with a specially developed diesel engine.

  6. A novel cascade organic Rankine cycle (ORC) system for waste heat recovery of truck diesel engines

    International Nuclear Information System (INIS)

    Chen, Tao; Zhuge, Weilin; Zhang, Yangjun; Zhang, Lei

    2017-01-01

    Highlights: • A confluent cascade expansion ORC (CCE-ORC) system is proposed. • Cyclopentane is considered as the most suitable fluid for this system. • The CCE-ORC system performance under full operating conditions is analyzed. • The BSFC of diesel engine can be reduced by 9.2% with the CCE-ORC system. • Performance comparison of CCE-ORC and dual-loop ORC is conducted. - Abstract: Waste heat recovery (WHR) of engines has attracted increasingly more concerns recently, as it can improve engine thermal efficiency and help truck manufacturers meet the restrictions of CO_2 emission. The organic Rankine cycle (ORC) has been considered as the most potential technology of WHR. To take full advantage of waste heat energy, the waste heat in both exhaust gases and the coolant need to be recovered; however, conventional multi-source ORC systems are too complex for vehicle applications. This paper proposed a confluent cascade expansion ORC (CCE-ORC) system for engine waste heat recovery, which has simpler architecture, a smaller volume and higher efficiency compared with conventional dual-loop ORC systems. Cyclopentane is analyzed to be regarded as the most suitable working fluid for this novel system. A thermodynamic simulation method is established for this system, and off-design performance of main components and the working fluid side pressure drop in the condenser have been taken into consideration. System performance simulations under full engine operating conditions are conducted for the application of this system on a heavy-duty truck diesel engine. Results show that the engine peak thermal efficiency can be improved from 45.3% to 49.5% where the brake specific fuel consumption (BSFC) decreases from 185.6 g/(kW h) to 169.9 g/(kW h). The average BSFC in the frequently operating region can decrease by 9.2% from 187.9 g/(kW h) to 172.2 g/(kW h). Compared with the conventional dual-loop ORC system, the CCE-ORC system can generate 8% more net power, while the

  7. Analytical solution to energy management guaranteeing battery life for hybrid trucks

    NARCIS (Netherlands)

    Pham, H.T.; Kessels, J.T.B.A.; van den Bosch, P.P.J.; Huisman, R.G.M.

    2016-01-01

    This paper considers a parallel hybrid electric truck where the tractive force delivered to the wheels can be provided by a conventional internal combustion engine (ICE) and/or a motor generator (MG). This hybrid truck is equipped with a clutch system that is capable of decoupling the ICE and the MG

  8. Engineering task plan for upgrades to the leveling jacks on core sample trucks number 3 and 4; TOPICAL

    International Nuclear Information System (INIS)

    KOSTELNIK, A.J.

    1999-01-01

    Characterizing the waste in underground storage tanks at the Hanford Site is accomplished by obtaining a representative core sample for analysis. Core sampling is one of the numerous techniques that have been developed for use given the environmental and field conditions at the Hanford Site. Core sampling is currently accomplished using either Push Mode Core Sample Truck No.1 or; Rotary Mode Core Sample Trucks No.2, 3 or 4. Past analysis (WHC 1994) has indicated that the Core Sample Truck (CST) leveling jacks are structurally inadequate when lateral loads are applied. WHC 1994 identifies many areas where failure could occur. All these failures are based on exceeding the allowable stresses listed in the American Institute of Steel Construction (AISC) code. The mode of failure is for the outrigger attachments to the truck frame to fail resulting in dropping of the CST and possible overturning (Ref. Ziada and Hundal, 1996). Out of level deployment of the truck can exceed the code allowable stresses in the structure. Calculations have been performed to establish limits for maintaining the truck level when lifting. The calculations and the associated limits are included in appendix A. The need for future operations of the CSTS is limited. Sampling is expected to be complete in FY-2001. Since there is limited time at risk for continued use of the CSTS with the leveling controls without correcting the structural problems, there are several design changes that could give incremental improvements to the operational safety of the CSTS with limited impact on available operating time. The improvements focus on making the truck easier to control during lifting and leveling. Not all of the tasks identified in this ETP need to be performed. Each task alone can improve the safety. This engineering task plan is the management plan document for implementing the necessary additional structural analysis. Any additional changes to meet requirements of standing orders shall require a

  9. DELTA-DIESEL ENGINE LIGHT TRUCK APPLICATION Contract DE-FC05-97OR22606 Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Hakim, Nabil Balnaves, Mike

    2003-05-27

    DELTA Diesel Engine Light Truck Application End of Contract Report DE-FC05-97-OR22606 EXECUTIVE SUMMARY This report is the final technical report of the Diesel Engine Light Truck Application (DELTA) program under contract DE-FC05-97-OR22606. During the course of this contract, Detroit Diesel Corporation analyzed, designed, tooled, developed and applied the ''Proof of Concept'' (Generation 0) 4.0L V-6 DELTA engine and designed the successor ''Production Technology Demonstration'' (Generation 1) 4.0L V-6 DELTA engine. The objectives of DELTA Program contract DE-FC05-97-OR22606 were to: Demonstrate production-viable diesel engine technologies, specifically intended for the North American LDT and SUV markets; Demonstrate emissions compliance with significant fuel economy advantages. With a clean sheet design, DDC produced the DELTA engine concept promising the following attributes: 30-50% improved fuel economy; Low cost; Good durability and reliability; Acceptable noise, vibration and harshness (NVH); State-of-the-art features; Even firing, 4 valves per cylinder; High pressure common rail fuel system; Electronically controlled; Turbocharged, intercooled, cooled EGR; Extremely low emissions via CLEAN Combustion{copyright} technology. To demonstrate the engine technology in the SUV market, DDC repowered a 1999 Dodge Durango with the DELTA Generation 0 engine. Fuel economy improvements were approximately 50% better than the gasoline engine replaced in the vehicle.

  10. Speed limiter integrated fatigue analyzer (SLIFA) for speed and fatigue control on diesel engine truck and bus

    Science.gov (United States)

    Wahyudi, Haris; Pranoto, Hadi; Leman, A. M.; Sebayang, Darwin; Baba, I.

    2017-09-01

    Every second, the number of road traffic deaths is increased globally with millions more sustaining severe injuries and living with long-term adverse health consequences. Jakarta alone in year 2015 had recorded 556 people died due to road accidents, approximately reached 6.231 road accident cases. The identified major contributory factors of such unfortunate events are both driver fatigue and over speeding habit especially related to the driving of truck and bus. This paper presents the idea on how to control the electronic system from input fuel system of injection pump and the combustion chamber engine will control the valve solenoid in injection pump which can lock and fuel will stop for moment, and speed limit can be success, by using sensor heart rate we can input reduce speed limit when fatigue detection driver. Integration process this tool can be relevant when Speed Limiter Integrated Fatigue Analyser (SLIFA) trial in the diesel engine for truck and bus, the result of this research Speed Limiter Integrated Fatigue Analyser (SLIFA) able to control speed of diesel engine for truck and bus almost 30km/h, 60km/h, and until 70 km/h. The installation of the sensor heart rate as the input speed limit SLIFA would work when the driver is detected to be in the fatigue condition. We make Speed Limiter Integrated Fatigue Analyser (SLIFA) for control and monitoring system for diesel engine in truck and bus. Speed Limiter Integrated Fatigue Analyser (SLIFA) system can save the historical of the speed record, fatigue, rpm, and body temperature of the driver.

  11. Reduced friction in engine sealing system for truck engines; Reibungsreduzierende Motorabdichtung bei Nutzfahrzeugmotoren

    Energy Technology Data Exchange (ETDEWEB)

    Reichert, Joachim [Kaco GmbH und Co. KG, Heilbronn (Germany). RADIA-Dichtsysteme; Schaefer, Peter [Kaco GmbH und Co. KG, Heilbronn (Germany). Nutzfahrzeuganwendungen

    2010-04-15

    The mechanical efficiency of the drive unit components, e.g. the prevention of friction loss, becomes more the focus point of many new developments in engines and drive trains. Radia rotary shaft seal rings as commonly used in utility vehicles cause an accordingly high friction, particularly when in big dimensions. Kaco has engineered a tailor made design of state of the art friction reducing sealing system generation called Fred. In the acronym ''F'' stands for friction and ''red'' stands for reduced. Kaco has defined three focus points of the performance profile from the already established Fred sealing system generation for further engineering when applied in utility vehicles. (orig.)

  12. EVALUATION METHOD OF FUEL-EFFICIENT DRIVING IN DUMP TRUCK USING VEHICLE SPEED AND ENGINE ROTATIONAL SPEED

    Science.gov (United States)

    Hirata, Masafumi; Yamamoto, Tatsuo; Yasui, Toshiaki; Hayashi, Mayu; Takebe, Atsuji; Funahashi, Masashi

    In the construction site, the light oil that the construction vehicle such as dump trucks uses accounts for 70 percent of the amount of the energy use. Therefore, the eco-driving education of the construction vehicle is effective in the fuel cost improvement and the CO2 reduction. The eco-driving education can be executed cheap and easily, and a high effect can be expected. However, it is necessary to evaluate the eco-driving situation of the construction vehicle exactly to maintain the educative effect for a long term. In this paper, the method for evaluating the effect of the fuel cost improvement was examined by using the vehicle speed and the engine rotational speed of the dump truck. In this method, "Ideal eco-driving model" that considers the difference between the vehicle model and the running condition (traffic jam etc.) is made. As a result, it is possible to evaluate the fuel consumption improvement effect of a dump truck by the same index.

  13. Controllable molecular motors engineered from myosin and RNA

    Science.gov (United States)

    Omabegho, Tosan; Gurel, Pinar S.; Cheng, Clarence Y.; Kim, Laura Y.; Ruijgrok, Paul V.; Das, Rhiju; Alushin, Gregory M.; Bryant, Zev

    2018-01-01

    Engineering biomolecular motors can provide direct tests of structure-function relationships and customized components for controlling molecular transport in artificial systems1 or in living cells2. Previously, synthetic nucleic acid motors3-5 and modified natural protein motors6-10 have been developed in separate complementary strategies to achieve tunable and controllable motor function. Integrating protein and nucleic-acid components to form engineered nucleoprotein motors may enable additional sophisticated functionalities. However, this potential has only begun to be explored in pioneering work harnessing DNA scaffolds to dictate the spacing, number and composition of tethered protein motors11-15. Here, we describe myosin motors that incorporate RNA lever arms, forming hybrid assemblies in which conformational changes in the protein motor domain are amplified and redirected by nucleic acid structures. The RNA lever arm geometry determines the speed and direction of motor transport and can be dynamically controlled using programmed transitions in the lever arm structure7,9. We have characterized the hybrid motors using in vitro motility assays, single-molecule tracking, cryo-electron microscopy and structural probing16. Our designs include nucleoprotein motors that reversibly change direction in response to oligonucleotides that drive strand-displacement17 reactions. In multimeric assemblies, the controllable motors walk processively along actin filaments at speeds of 10-20 nm s-1. Finally, to illustrate the potential for multiplexed addressable control, we demonstrate sequence-specific responses of RNA variants to oligonucleotide signals.

  14. 40 CFR 80.522 - May used motor oil be dispensed into diesel motor vehicles or nonroad diesel engines?

    Science.gov (United States)

    2010-07-01

    ... diesel motor vehicles or nonroad diesel engines? 80.522 Section 80.522 Protection of Environment... vehicles or nonroad diesel engines? No person may introduce used motor oil, or used motor oil blended with... later nonroad diesel engines (not including locomotive or marine diesel engines), unless both of the...

  15. The impact of hybrid engines on fuel consumption and emissions of heavy-duty trucks

    NARCIS (Netherlands)

    Bal, F; Vleugel, J.M.; Brebbia, CA; Sendra, J

    2017-01-01

    Overland transport of goods mainly goes by road. Road freight transport, trucking in particular, has a large share in the energy consumption, CO2-emissions and air pollution by human activities. This will become an even bigger issue with the expected massive growth of road freight

  16. Solar hydrogen for urban trucks

    Energy Technology Data Exchange (ETDEWEB)

    Provenzano, J.: Scott, P.B.; Zweig, R. [Clean Air Now, Northridge, CA (United States)

    1997-12-31

    The Clean Air Now (CAN) Solar Hydrogen Project, located at Xerox Corp., El Segundo, California, includes solar photovoltaic powered hydrogen generation, compression, storage and end use. Three modified Ford Ranger trucks use the hydrogen fuel. The stand-alone electrolyzer and hydrogen dispensing system are solely powered by a photovoltaic array. A variable frequency DC-AC converter steps up the voltage to drive the 15 horsepower compressor motor. On site storage is available for up to 14,000 standard cubic feet (SCF) of solar hydrogen, and up to 80,000 SCF of commercial hydrogen. The project is 3 miles from Los Angeles International airport. The engine conversions are bored to 2.9 liter displacement and are supercharged. Performance is similar to that of the Ranger gasoline powered truck. Fuel is stored in carbon composite tanks (just behind the driver`s cab) at pressures up to 3600 psi. Truck range is 144 miles, given 3600 psi of hydrogen. The engine operates in lean burn mode, with nil CO and HC emissions. NO{sub x} emissions vary with load and rpm in the range from 10 to 100 ppm, yielding total emissions at a small fraction of the ULEV standard. Two trucks have been converted for the Xerox fleet, and one for the City of West Hollywood. A public outreach program, done in conjunction with the local public schools and the Department of Energy, introduces the local public to the advantages of hydrogen fuel technologies. The Clean Air Now program demonstrates that hydrogen powered fleet development is an appropriate, safe, and effective strategy for improvement of urban air quality, energy security and avoidance of global warming impact. Continued technology development and cost reduction promises to make such implementation market competitive.

  17. EFFECTS OF ENGINE SPEED AND ACCESSORY LOAD ON IDLING EMISSIONS FROM HEAVY-DUTY DIESEL TRUCK ENGINES

    Science.gov (United States)

    A nontrivial portion of heavy-duty vehicle emissions of nitrogen oxides (NOx) and particulate matter (PM) occurs during idling. Regulators and the environmental community are interested in curtailing truck idling emissions, but current emissions models do not characterize them ac...

  18. Thermodynamic analysis of a Rankine cycle applied on a diesel truck engine using steam and organic medium

    International Nuclear Information System (INIS)

    Katsanos, C.O.; Hountalas, D.T.; Pariotis, E.G.

    2012-01-01

    Highlights: ► ORC improves bsfc from 10.7% to 8.4% as engine load increases from 25% to 100%. ► Increasing ORC high pressure increases thermodynamic efficiency and power output. ► Operating at high pressure the ORC is favorable for the engine cooling system. ► The low temperature values of the ORC favors heat extraction from the EGR gas. ► The impact of the exhaust gas heat exchanger on engine backpressure is limited. - Abstract: A theoretical study is conducted to investigate the potential improvement of the overall efficiency of a heavy-duty truck diesel engine equipped with a Rankine bottoming cycle for recovering heat from the exhaust gas. To this scope, a newly developed thermodynamic simulation model has been used, considering two different working media: water and the refrigerant R245ca. As revealed from the analysis, due to the variation of exhaust gas temperature with engine load it is necessary to modify the Rankine cycle parameters i.e. high pressure and superheated vapor temperature. For this reason, a new calculation procedure is applied for the estimation of the optimum Rankine cycle parameters at each operating condition. The calculation algorithm is conducted by taking certain design criteria into account, such as the exhaust gas heat exchanger size and its pinch point requirement. From the comparative evaluation between the two working media examined, using the optimum configuration of the cycle for each operating condition, it has been revealed that the brake specific fuel consumption improvement ranges from 10.2% (at 25% engine load) to 8.5% (at 100% engine load) for R245ca and 6.1% (at 25% engine load) to 7.5% (at 100% engine load) for water.

  19. Development and experimental testing of a hybrid Stirling engine-adsorption chiller auxiliary power unit for heavy trucks

    International Nuclear Information System (INIS)

    Flannery, Barry; Lattin, Robert; Finckh, Oliver; Berresheim, Harald; Monaghan, Rory F.D.

    2017-01-01

    Highlights: • Free-piston Stirling engine for truck APU. • Waste heat driven adsorption chiller for cab air conditioning. • Reduced-order model comparing proposed system to existing technology. • Experimental test data from prototype test rig. - Abstract: This paper identifies the key technical requirements for a heavy truck auxiliary power unit (APU) and explores a potential alternative technology for use in a next-generation APU which could eliminate key problems related to emissions, noise and maintenance experienced today by conventional diesel engine-vapour compression APUs. The potential performance of a novel hybrid Stirling engine-adsorption chiller concept is investigated and benchmarked against the incumbent technology using a reduced-order model based on experimental data. Experimental results from a Stirling-adsorption system (SAS) prototype test rig are also presented which highlight system integration dynamics and overall performance. The adsorption chiller achieved an average COP of 0.42 ± 0.06 and 2.3 ± 0.1 kW_t of cooling capacity at the baseline test condition. The prototype SAS test rig demonstrates that there appear to be no major technology barriers remaining that would prevent adoption of the SAS concept in a next-generation APU. Such a system could offer a reduction of exhaust emissions, greenhouse gases (GHG), ozone-depleting substances, noise, low maintenance and the potential for fuel flexibility and higher reliability. Preliminary modelling results indicate that the proposed system could offer superior overall electrical and cooling efficiencies compared to incumbent APUs and demonstrate a payback period of 4.6 years.

  20. Program Guide for Diesel Engine Mechanics 8742000 (IN47.060500) and Heavy Duty Truck and Bus Mechanics DIM0991 (IN47.060501).

    Science.gov (United States)

    University of South Florida, Tampa. Coll. of Education.

    This competency-based program guide provides course content information and procedures for secondary schools, postsecondary vocational schools, and community colleges in Florida that conduct programs in diesel engine mechanics and heavy duty truck and bus mechanics. The first section is on legal authority, which applies to all vocational education…

  1. Norcal Prototype LNG Truck Fleet: Final Results

    Energy Technology Data Exchange (ETDEWEB)

    2004-07-01

    U.S. DOE and National Renewable Energy Laboratory evaluated Norcal Waste Systems liquefied natural gas (LNG) waste transfer trucks. Trucks had prototype Cummins Westport ISXG engines. Report gives final evaluation results.

  2. Engineering controllable bidirectional molecular motors based on myosin

    Science.gov (United States)

    Chen, Lu; Nakamura, Muneaki; Schindler, Tony D.; Parker, David; Bryant, Zev

    2012-04-01

    Cytoskeletal motors drive the transport of organelles and molecular cargoes within cells and have potential applications in molecular detection and diagnostic devices. Engineering molecular motors with controllable properties will allow selective perturbation of mechanical processes in living cells and provide optimized device components for tasks such as molecular sorting and directed assembly. Biological motors have previously been modified by introducing activation/deactivation switches that respond to metal ions and other signals. Here, we show that myosin motors can be engineered to reversibly change their direction of motion in response to a calcium signal. Building on previous protein engineering studies and guided by a structural model for the redirected power stroke of myosin VI, we have constructed bidirectional myosins through the rigid recombination of structural modules. The performance of the motors was confirmed using gliding filament assays and single fluorophore tracking. Our strategy, in which external signals trigger changes in the geometry and mechanics of myosin lever arms, should make it possible to achieve spatiotemporal control over a range of motor properties including processivity, stride size and branchpoint turning.

  3. Engineering controllable bidirectional molecular motors based on myosin

    Science.gov (United States)

    Chen, Lu; Nakamura, Muneaki; Schindler, Tony D.; Parker, David; Bryant, Zev

    2012-01-01

    Cytoskeletal motors drive the transport of organelles and molecular cargoes within cells1, and have potential applications in molecular detection and diagnostic devices2,3. Engineering molecular motors with dynamically controllable properties will allow selective perturbation of mechanical processes in living cells, and yield optimized device components for complex tasks such as molecular sorting and directed assembly3. Biological motors have previously been modified by introducing activation/deactivation switches that respond to metal ions4,5 and other signals6. Here we show that myosin motors can be engineered to reversibly change their direction of motion in response to a calcium signal. Building on previous protein engineering studies7–11 and guided by a structural model12 for the redirected power stroke of myosin VI, we constructed bidirectional myosins through the rigid recombination of structural modules. The performance of the motors was confirmed using gliding filament assays and single fluorophore tracking. Our general strategy, in which external signals trigger changes in the geometry and mechanics of myosin lever arms, should enable spatiotemporal control over a range of motor properties including processivity, stride size13, and branchpoint turning14. PMID:22343382

  4. Motor vehicles and internal combustion engines; Kraftfahrwesen und Verbrennungsmotoren

    Energy Technology Data Exchange (ETDEWEB)

    Bargende, M.; Wiedemann, J. [eds.

    1999-07-01

    The book comprises the papers presented at the 3rd Stuttgart symposium. It reviews the state of the art in science and engineering and outlines future perspectives in the fields of motor vehicles and internal combustion engines. As the conference, the book comprises three sections: 'Engines' on DI spark ignition engines and diesel engines, mixing, combustion and exhaust purification. 'Motor cars' discusses acoustics and aeroacoustics, aerodynamics and wind tunnel technology, comfort, driving gear and stability control. 'Motor vehicle systems' contains papers on thermomanagement, control and automation, real-time applications in motor car simulation, software tools in the control systems development process, and simulation in motor vehicle systems development. Finally, the plenary paper 'Fuel cells, a solution for non-polluting motor car drives' by Dr.-Ing. F. Panik is also contained in the book. [German] Das vorliegende Buch enthaelt die Vortraege des 3. Stuttgarter Symposiums. Es gibt einen Ueberblick ueber den aktuellen Stand von Wissenschaft und Technik und zeigt zukuenftige Perspektiven im Bereich Kraftfahrwesen und Verbrennungsmotoren. Entsprechend der Tagung gliedert sich das Buch in drei Teile. Teil 1 'Motoren' besteht aus Vortraegen ueber Ottomotoren mit Direkteinspritzung und Dieselmotoren, Gemischbildung, Verbrennung und Abgasnachbehandlung, Analyse, Simulation und Motorkomponenten. Teil 2 'Kraftfahrzeuge' enthaelt Arbeiten ueber Fahrzeugakustik und Aeroakustik, Fahrzeug-Aerodynamik und Windkanaltechnik, Fahrzeugkomfort, Fahrwerk und Fahrdynamik. Teil 3 'Kraftfahrzeugsystemtechnik' enthaelt Beitraege ueber Thermomanagement, Regelungs- und Automatisierungstechnik, Echtzeitanwendungen in der Kfz-Simulationstechnik, Softwaretools im Steuergeraete-Entwicklungsprozess und Simulation in der Kraftfahrzeug-Systementwicklung. Der abschliessende Plenarvortrag des Symposiums &apos

  5. 40 CFR 85.1506 - Inspection and testing of imported motor vehicles and engines.

    Science.gov (United States)

    2010-07-01

    ... motor vehicles and engines. 85.1506 Section 85.1506 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Importation of Motor Vehicles and Motor Vehicle Engines § 85.1506 Inspection and testing of imported motor vehicles and...

  6. The homopolar motor: A true relativistic engine

    Science.gov (United States)

    Guala-Valverde, Jorge; Mazzoni, Pedro; Achilles, Ricardo

    2002-10-01

    This article discusses experiments which enable the identification of the seat of mechanical forces in homopolar-machines reported earlier in this journal [J. Guala-Valverde and P. Mazzoni, Am. J. Phys. 63, 228-229 (1995); J. Guala-Valverde, P. Mazzoni, and K. Blas, ibid. 65, 147-148 (1997)]. We provide a suitable variation on a recent work "The Unipolar Dynamotor: A Genuine Relational Engine" [J. Guala-Valverde and P. Mazzoni, Apeiron 8, 41-52 (2001)], where "relational" implies "absolutely relativistic." Our view agrees with both Weber's recognition in the 19th century of the importance of relative motion in electromagnetic phenomena [A. K. T. Assis, Electrodynamics (Kluwer, Dordrecht, 1994)] and Einstein's 1905 statement concerning electromagnetism [Ann. Phys. 17, 891-921 (1905)].

  7. Demonstration of fleet trucks fueled with PV hydrogen

    International Nuclear Information System (INIS)

    Provenzano, J.; Scott, P.B.; Zweig, R.

    1998-01-01

    The Clean Air Now (CAN) Solar Hydrogen Project has been installed at the Xerox Corporation, El Segundo, California site. Three Ford Ranger trucks have been converted to use hydrogen fuel. The ''stand- alone'' electrolyzer and hydrogen dispensing system is powered by a photovoltaic array with no connection to the power grid. A variable frequency DC/AC converter steps up the voltage to drive the 15 hp motor for the hydrogen compressor. Up to 400 standard cubic meters (SCM) of solar hydrogen is stored, and storage of up to 2300 SCM of commercial hydrogen is collocated. As the hydrogen storage is within 5km of Los Angeles International Airport, pilot operation of a hydrogen fuel cell bus for airport shuttle service has been demonstrated with fueling at the CAN facility. The truck engine conversions are bored to 2.91 displacement, use a Roots type supercharger and CVI (constant volume injection) fuel induction to allow performance similar to that of the gasoline powered truck. Truck fuel storage is done with carbon composite tanks at pressures up to 24.8 MPa (3600 psi). Two tanks are located just behind the driver's cab, and take up nearly half of the truck bed space. The truck highway range is approximately 140 miles. The engine operates in lean burn mode, with nil emissions of CO and HC. NO x emissions vary with load and rpm in the range from 10 to 100 ppm, yielding total emissions at a small fraction of the ULEV standard. Two Xerox fleet trucks have been converted, and one for the City of West Hollywood. The Clean Air Now Program demonstrates that hydrogen powered fleet development is an appropriate safe, and effective strategy for improvement of urban air quality. It further demonstrates that continued technological development and cost reduction will make such implementation competitive. (Author)

  8. Engineering task plan for the development, fabrication and installation of rotary mode core sample truck grapple hoist box level wind system

    International Nuclear Information System (INIS)

    BOGER, R.M.

    1999-01-01

    This Engineering Task Plan is to design, generate fabrication drawings, fabricate, test, and install the grapple hoist level wind system for Rotary Mode Core Sample Trucks (RMCST) 3 and 4. Deliverables will include generating fabrication drawings, fabrication of one level wind system, updating fabrication drawings as required, and installation of level wind systems on RMCST 3 or 4. The installation of the level wind systems will be done during a preventive maintenance outage

  9. Modeling and Simulation of Truck Engine Cooling System for Onboard Diagnosis

    Institute of Scientific and Technical Information of China (English)

    朱正礼; 张建武; 包继华

    2004-01-01

    A cooling system model of a selected internal combustion engine has been built for onboard diagnosis. The model uses driving cycle data available within the production Engine Control Module (ECM): vehicle speed, engine speed, and fuel flow rate for the given ambient temperature and pressure, etc. Based on the conservation laws for heat transfer and mass flow process, the mathematical descriptions for the components involved in the cooling circuit are obtained and all the components are integrated into a model on Matlab/Simulink platform. The model can simulate the characteristics of thermostat (e.g. time-lag, hysteresis effect).The changes of coolant temperature, heat transfer flow rate, and pressure at individual component site are also shown.

  10. Use of diesel engines in industrial trucks operated in enclosed spaces

    Energy Technology Data Exchange (ETDEWEB)

    Dietrich, W; Reibold, G

    1981-01-01

    Report on emission investigations on a fork-lifter equipped with a low-pollutant MWM-engine, tests were carried out in enclosed spaces. The aim was to clarify if the maximum MPC at a place of work listed in a table of waste gas components can be observed even under unfavourable operating conditions of the fork lifter. The test is described, results are analysed. It is proved that there are no health hazards for the staff even under the extreme conditions chosen for the test.

  11. 76 FR 20251 - Federal Motor Vehicle Theft Prevention Standard; Final Listing of 2012 Light Duty Truck Lines...

    Science.gov (United States)

    2011-04-12

    ... the incidence of motor vehicle theft by facilitating the tracing and recovery of parts from stolen vehicles. The standard seeks to facilitate such tracing by requiring that vehicle identification numbers... all exemptions on our Web site. However, we believe that re-publishing a list containing vehicle lines...

  12. 77 FR 32903 - Federal Motor Vehicle Theft Prevention Standard; Final Listing of 2013 Light Duty Truck Lines...

    Science.gov (United States)

    2012-06-04

    ... the incidence of motor vehicle theft by facilitating the tracing and recovery of parts from stolen vehicles. The standard seeks to facilitate such tracing by requiring that vehicle identification numbers... exemptions on our Web site. However, we believe that republishing a list containing vehicle lines that have...

  13. 75 FR 34946 - Federal Motor Vehicle Theft Prevention Standard; Final Listing of 2011 Light Duty Truck Lines...

    Science.gov (United States)

    2010-06-21

    ... the incidence of motor vehicle theft by facilitating the tracing and recovery of parts from stolen vehicles. The standard seeks to facilitate such tracing by requiring that vehicle identification numbers... continue to maintain a comprehensive database of all exemptions on our Web site. However, we believe that...

  14. 77 FR 9916 - California State Motor Vehicle and Nonroad Engine Pollution Control Standards; Mobile Cargo...

    Science.gov (United States)

    2012-02-21

    ... performance standards for engines equipped in newly purchased, leased, or rented (collectively known as... section 209 proceeding is to: Consider all evidence that passes the threshold test of materiality and... regulations also set forth in- use performance standards applicable to non-new yard and non-yard trucks. To...

  15. Technical and economic study of Stirling and Rankine cycle bottoming systems for heavy truck diesel engines

    Science.gov (United States)

    Kubo, I.

    1987-01-01

    Bottoming cycle concepts for heavy duty transport engine applications were studied. In particular, the following tasks were performed: (1) conceptual design and cost data development for Stirling systems; (2) life-cycle cost evaluation of three bottoming systems - organic Rankine, steam Rankine, and Stirling cycles; and (3) assessment of future directions in waste heat utilization research. Variables considered for the second task were initial capital investments, fuel savings, depreciation tax benefits, salvage values, and service/maintenance costs. The study shows that none of the three bottoming systems studied are even marginally attractive. Manufacturing costs have to be reduced by at least 65%. As a new approach, an integrated Rankine/Diesel system was proposed. It utilizes one of the diesel cylinders as an expander and capitalizes on the in-cylinder heat energy. The concept eliminates the need for the power transmission device and a sophisticated control system, and reduces the size of the exhaust evaporator. Results of an economic evaluation indicate that the system has the potential to become an attractive package for end users.

  16. THE INJURY SEVERITY RATE DIFFERENCES IN PASSENGER CARS AND PICK UP TRUCKS RELATED TWO VEHICLE INVOLVED MOTOR VEHICLE CRASHES IN BRITISH COLUMBIA, CANADA

    Directory of Open Access Journals (Sweden)

    E.B.R. DESAPRIYA

    2004-01-01

    Full Text Available The effect of large vehicle involvement on motor vehicle crash (MVC rates and severity has long been a concern in MVC analysis literature. Injuries in drivers and occupants are related to several key factors: the mass of the case vehicle and mass of its collision partner and speed of case vehicle and collision partner at the time of the crash. Objective: To evaluate the relative risk of injury occurrence in collisions between picks up trucks (PU and passenger sedan cars (PS. Methods: Data from the Insurance Corporation of British Columbia (ICBC crash data base was used to determine MVC rates and injury occurrence. Descriptive characteristics of the injury location and injury type were analyzed comparing the Odds Ratios and chi-squares. Results: PS occupants received more injuries; Odds Ratio was 2.49 (95% confidence interval: 2.15–2.88. Conclusion: Occupants in PS which collide with PU were at twice the risk of injuries. Concussion, whiplash, lacerations and abrasion were more frequent in PS drivers and occupants than in PU drivers and occupants. Overall, PS drivers/occupants experienced greater injuries than PU drivers/occupants in PU-PS collisions. In this paper, results are shown as odds ratios comparing occupants injuries in PS (case group with occupant injuries in PU (control group.

  17. Luggage truck

    NARCIS (Netherlands)

    Oosterhuis, E.J.; Luttekes, E.; Rijsenbrij, J.C.

    2004-01-01

    The present invention relates to a luggage truck (2) comprising a loading space for luggage and provided with a conveyor belt (14) disposed in the loading space for the supply and removal of luggage, which conveyor belt is at the same time a storage unit for the luggage, wherein the conveyor belts

  18. Large Truck Crash Causation Study (LTCCS)

    Data.gov (United States)

    Department of Transportation — The Large Truck* Crash Causation Study (LTCCS) is based on a three-year data collection project conducted by the Federal Motor Carrier Safety Administration (FMCSA)...

  19. Reducing truck emissions at container terminals in a low carbon economy

    DEFF Research Database (Denmark)

    Chen, Gang; GOVINDAN, Kannan; Golias, Mihalis M.

    2013-01-01

    This study proposes a methodology to optimize truck arrival patterns to reduce emissions from idling truck engines at marine container terminals. A bi-objective model is developed minimizing both truck waiting times and truck arrival pattern change. The truck waiting time is estimated via...... a queueing network. Based on the waiting time, truck idling emissions are estimated. The proposed methodology is evaluated with a case study, where truck arrival rates vary over time. We propose a Genetic Algorithm based heuristic to solve the resulting problem. Result shows that, a small shift of truck...... arrivals can significantly reduce truck emissions, especially at the gate....

  20. 78 FR 25525 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-05-01

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration..., which applied to participate in the Agency's long-haul pilot program to test and demonstrate the ability... long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled motor carriers...

  1. Numerical Evaluation ofThe Performance ofA Compression Ignition Cng Engine For Heavy DutyTrucksWithAn Optimum Speed PowerTurbine

    Directory of Open Access Journals (Sweden)

    Alberto A. Boretti

    2011-10-01

    Full Text Available The turbocharged direct injection lean burn Diesel engine is the most efficient engine now in production for transport applications. CNG is an alternative fuel with a better carbon to hydrogen ratio therefore permitting reduced carbon dioxide emissions. It is injected in gaseous form for a much cleaner combustion almost cancelling some of the emissions of the Diesel and it permits a much better energy security within Australia. The paper discusses the best options currently available to convert Diesel engine platforms to CNG, with particular emphasis to the use of these CNG engines within Australia where the refuelling network is scarce. This option is determined in the dual fuel operation with a double injector design that couples a second CNG injector to the Diesel injector. This configuration permits the operation Diesel only or Diesel pilot and CNG main depending on the availability of refuelling stations where the vehicle operates. Results of engine performance simulations are performed for a straight six cylinder 13 litres truck engine with a novel power turbine connected to the crankshaft through a constant variable transmission that may be by-passed when non helpful to increase the fuel economy of the vehicle or when damaging the performances of the after treatment system.

  2. Technologies for simulation improvement of NOx and PM emissions and fuel consumption of future diesel engines for heavy-duty trucks; Shorai no ogatasha diesel engine ni okeru NOx, PM, nenryo shohi no kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Shimoda, M.; Shimokawa, K.; Uchida, N.; Tsuji, Y.; Yokotaa, H.; Hosoya, M. [Hino Motors, Ltd., Tokyo (Japan)

    1999-01-01

    Future diesel engines for heavy-duty trucks are required to have significantly low NO{sub x} and PM emissions and fuel consumption characteristics. In order to improve these characteristics, various technologies including high pressure fuel injection systems, combustion optimization. high boost pressure turbocharging, EGR homogeneous charge compression ignition combined with multiple injections, and aftertreatment are discussed. As each technology has a number of challenges to overcome, it will take long before engines with these technologies are commercially available. In this paper, the research activities accomplished to date are reported. (author)

  3. Final Rule for Control of Air Pollution From New Motor Vehicles and New Motor Vehicle Engines; Non-Conformance Penalties for 2004 and later Model Year Emission Standards for Heavy-Duty Diesel Engines and Heavy-Duty Diesel Vehicles

    Science.gov (United States)

    Final Rule for Control of Air Pollution From New Motor Vehicles and New Motor Vehicle Engines; Non-Conformance Penalties for 2004 and later Model Year Emission Standards for Heavy-Duty Diesel Engines and Heavy-Duty Diesel Vehicles

  4. AC, DC or EC motor? What type of engine for what purpose?; AC-, DC- oder EC-Motor? Welche Motorausfuehrung fuer welchen Zweck

    Energy Technology Data Exchange (ETDEWEB)

    Zeiff, Andreas; Homburg, Dietrich

    2009-01-15

    Electronics is the key technology in control engineering, but even the best control system requires reliable modules to transmit signals. Modern electric motors have become indispensable here. There are nearly as many motor types as there are applications. Electromagnetic conversion of electric into mechanical power is directly related to motor design. There are AC and DC motors, one-speed motors and variable-speed motors. Rotary momentum and synchronisation can be optimized by selecting the appropriate motor type, as can dynamics and detent torque. Correct selection of the electric motor therefore is essential for an optimal drive concept. (orig.)

  5. Controller for computer control of brushless dc motors. [automobile engines

    Science.gov (United States)

    Hieda, L. S. (Inventor)

    1981-01-01

    A motor speed and torque controller for brushless d.c. motors provides an unusually smooth torque control arrangement. The controller provides a means for controlling a current waveform in each winding of a brushless dc motor by synchronization of an excitation pulse train from a programmable oscillator. Sensing of torque for synchronization is provided by a light beam chopper mounted on the motor rotor shaft. Speed and duty cycle are independently controlled by controlling the frequency and pulse width output of the programmable oscillator. A means is also provided so that current transitions from one motor winding to another is effected without abrupt changes in output torque.

  6. Truck Thermoacoustic Generator and Chiller

    Energy Technology Data Exchange (ETDEWEB)

    Keolian, Robert

    2011-03-31

    This Final Report describes the accomplishments of the US Department of Energy (DOE) cooperative agreement project DE-FC26-04NT42113 - Truck Thermoacoustic Generator and Chiller - whose goal is to design, fabricate and test a thermoacoustic piezoelectric generator and chiller system for use on over-the-road heavy-duty-diesel trucks, driven alternatively by the waste heat of the main diesel engine exhaust or by a burner integrated into the thermoacoustic system. The thermoacoustic system would utilize engine exhaust waste heat to generate electricity and cab air conditioning, and would also function as an auxiliary power unit (APU) for idle reduction. The unit was to be tested in Volvo engine performance and endurance test cells and then integrated onto a Class 8 over-the-road heavy-duty-diesel truck for further testing on the road. The project has been a collaboration of The Pennsylvania State University Applied Research Laboratory, Los Alamos National Laboratory, Clean Power Resources Inc., and Volvo Powertrain (Mack Trucks Inc.). Cost share funding was provided by Applied Research Laboratory, and by Clean Power Resources Inc via its grant from Innovation Works - funding that was derived from the Commonwealth of Pennsylvania. Los Alamos received its funding separately through DOE Field Work Proposal 04EE09.

  7. Solid propellant ignition motors for LH_2/LOX rocket engine system

    OpenAIRE

    ARAKI, Tetsuo; AKIBA, Ryojiro; HASHIMOTO, Yasunari; AIHARA, Kenji; TOMITA, Etsu; YASUDA, Seiichi; 荒木, 哲夫; 秋葉, 鐐二郎; 橋本, 保成; 相原, 賢二; 富田, 悦; 安田, 誠一

    1983-01-01

    Solid propellant ignition motors are used in the series of experiments of the 10 ton LH_2/LOX engine featured by the channel wall thrust chamber, This paper presents design specification, experiments and results obtained by actual applications of those ignition motors.

  8. Technology for semi-endless use of lubricating oil, no waste oil, improvement of reliability and keeping high thermal efficiency in engines; Jinzo kino seijo gijutsu ni yoru engine oil no han`eikyu shiyo to haiyu zero, oyobi shinraisei kojo to netsukoritsu teika no boshi (joyosha ni yoru shiken oyobi truck ni okeru jitsuyoka)

    Energy Technology Data Exchange (ETDEWEB)

    Azuma, T [Teikyo University, Tokyo (Japan); Sumimoto, M; Kimura, I

    1997-10-01

    The authors have developed a new technology which enables it to use lubricating oil almost forever without any waste oil, only compensating lost oil and additives. The system has been working well in many marine and co-generation diesel engines. These engines have been also free from most of engine troubles. This paper reports the test results made on a car and some trucks. Besides above mentioned advantages, the results show that high thermal efficiency has been kept for more than ten years in the car tested and that the exhaust gas brake is much improved in the trucks. 8 refs., 4 figs.

  9. A Qualitative Study of the European Trucking Industry and Logistics Strategies Using the United States Motor Carrier Industry as a Guide

    Science.gov (United States)

    1992-09-01

    interpretation of the data (Rommerskirchen, 1986:14). In addition to tax differences, the basic costs of operations vary among EC-member states. License fees...aggregation impossible" (Aberle, 1985:18). 4. "Not only are special statistics on nationally specific transport expenditure incomplete, but even the basic ...industry. Various studies concluded that the trucking industry’s collective ratemaking system, composed of regional rate bureaus, resulted in rates in the

  10. Investigating impact of motor oil quality on vehicles engine induced noise level

    Directory of Open Access Journals (Sweden)

    I. Arefian

    2015-09-01

    Full Text Available Introduction: Vehicle engine id one of the main sources of noise which its level is influenced by various parameters. The aim of this study was to investigate the impact of motor oils quality before and after oil change on the variability of vehicle engine induced noise level. In this study it is tried to follow-up the efficacy of motor oil quality on engines sound level. Material and Method: First, engine noise of 94 vehicles were recorded for 30 seconds before and after oil change and all the vehicles technical information including mileage, type of motor oil, and type of vehicle were registered. Following, the recorded noises were calibrated in semi-anechoic chamber and the sound pressure levels were measured with A and C-weighting network and main octav bands, using a sound level meters. The obtained results analyzed using SPSS software version 17. Results: The effects of motor oil quality on different noise levels of engines were determined and a significant reduction in noise level of vehicles engine was observed. Investigation of the relationship between mileage and motor oil quality on various engines sound level manifested that vehicles with mileage ranged 100000-150000 miles had significant reduction in their sound pressure levels in comparison with other vehicles. Conclusion: The results revealed that engine oil is among factors reducing the vehicle engine induced noise level. Moreover, the engine oil type and the vehicle mileage are key variables which determine the impact of engine oil quality on reduction of the sound level of vehicles engine.

  11. Comparative Analysis of Miniature Internal Combustion Engine and Electric Motor for UAV Propulsion

    Science.gov (United States)

    Chiclana, Branden Mark

    This thesis compares the performance of an engine/fuel tank based propulsion system to a motor/battery based propulsion system of equal total mass. The results show that the endurance of the engine/fuel system at the same thrust output is approximately 5 times greater than that of the motor/battery system. This is a direct result of the fact that the specific energy of the fuel is 20 times that of the lithium-polymer batteries used to power the motor. A method is also developed to account for the additional benefits of fuel consumption (and hence weight reduction) over the course of the flight. Accounting for this effect can increase endurance exponentially. Taken together, the results also demonstrate the dramatic performance improvements that are possible simply by replacing motor/battery systems with engine/fuel systems on small unmanned air vehicles.

  12. 76 FR 56868 - Pilot Project on NAFTA Trucking Provisions

    Science.gov (United States)

    2011-09-14

    ...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that have applied to participate in the Agency's long- haul pilot program to test and demonstrate the... proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot program to test and...

  13. 77 FR 12356 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2012-02-29

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that applied to participate in the Agency's long-haul pilot program to test and demonstrate the ability... cross-border long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled...

  14. 77 FR 40938 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2012-07-11

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... Morales Guevara (DBA Fletes Morales) which applied to participate in the Agency's long-haul pilot program...] its intent to proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot...

  15. 77 FR 27837 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2012-05-11

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... carriers that applied to participate in the Agency's long- haul pilot program to test and demonstrate the... intent to proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot program to...

  16. 78 FR 24293 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-04-24

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... in the Agency's long-haul pilot program to test and demonstrate the ability of Mexico- domiciled... cross-border long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled...

  17. 76 FR 56272 - Pilot Project on NAFTA Trucking Provisions

    Science.gov (United States)

    2011-09-12

    ...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that have applied to participate in the Agency's long- haul pilot program to test and demonstrate the... cross-border long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled...

  18. 76 FR 73765 - Pilot Project on NAFTA Trucking Provisions

    Science.gov (United States)

    2011-11-29

    ...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that have applied to participate in the Agency's long- haul pilot program to test and demonstrate the... proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot program to test and...

  19. Investigation of a Novel Coaxial Power-Split Hybrid Powertrain for Mining Trucks

    Directory of Open Access Journals (Sweden)

    Weiwei Yang

    2018-01-01

    Full Text Available Due to the different working conditions and specification requirements of mining trucks when compared to commercial passenger vehicles, better fuel efficiency of mining trucks could lead to more significant economic benefits. Therefore, investigating a hybrid transmission system becomes essential. A coaxial power-split hybrid powertrain system for mining trucks is presented in this paper. The system is characterized as comprising an engine, a generator (MG1, a motor (MC2, two sets of planetary gears, and a clutch (CL1. There are six primary operation modes for the hybrid system including the electric motor mode, the engine mode, the hybrid electric mode, the hybrid and assist mode, the regenerative mode, and the stationary charging mode. The mathematical model of the coaxial power-split hybrid system is established according to the requirements of vehicle dynamic performance and fuel economy performance in a given driving cycle. A hybrid vehicle model based on a rule-based control strategy is established to evaluate the fuel economy. Compared with the Toyota Hybrid System (THS and the conventional mechanical vehicle system using a diesel engine, the simulation results based on an enterprise project indicate that the proposed hybrid system can enhance the vehicle’s fuel economy by 8.21% and 22.45%, respectively, during the given mining driving cycle. The simulation results can be used as a reference to study the feasibility of the proposed coaxial hybrid system whose full potential needs to be further investigated by adopting non-causal control strategies.

  20. 76 FR 78 - Federal Motor Vehicle Safety Standard; Engine Control Module Speed Limiter Device

    Science.gov (United States)

    2011-01-03

    ... [Docket No. NHTSA-2007-26851] Federal Motor Vehicle Safety Standard; Engine Control Module Speed Limiter... occupants. IIHS stated that on-board electronic engine control modules (ECM) will maintain the desired speed... be equipped with an electronic control module (ECM) that is capable of limiting the maximum speed of...

  1. 46 CFR 11.522 - Service requirements for assistant engineer (limited oceans) of steam and/or motor vessels.

    Science.gov (United States)

    2010-10-01

    ... oceans) of steam and/or motor vessels. 11.522 Section 11.522 Shipping COAST GUARD, DEPARTMENT OF HOMELAND... Requirements for Engineer Officer § 11.522 Service requirements for assistant engineer (limited oceans) of... assistant engineer (limited oceans) of steam and/or motor vessels is three years of service in the...

  2. Modernization of gas-turbine engines with high-frequency induction motors

    Science.gov (United States)

    Abramovich, B. N.; Sychev, Yu A.; Kuznetsov, P. A.

    2018-03-01

    Main tendencies of growth of electric energy consumption in general and mining industries were analyzed in the paper. A key role of electric drive in this process was designated. A review about advantages and disadvantages of unregulated gearboxes with mechanical units that are commonly used in domestically produced gas-turbine engines was made. This review allows one to propose different gas-turbine engines modernization schemes with the help of PWM-driven high-frequency induction motors. Induction motors with the double rotor winding were examined. A simulation of high-frequency induction motors with double rotor windings in Matlab-Simulink software was carried out based on equivalent circuit parameters. Obtained characteristics of new motors were compared with serially produced analogues. After the simulation, results were implemented in the real prototype.

  3. Internal combustion engines for alcohol motor fuels: a compilation of background technical information

    Energy Technology Data Exchange (ETDEWEB)

    Blaser, Richard

    1980-11-01

    This compilation, a draft training manual containing technical background information on internal combustion engines and alcohol motor fuel technologies, is presented in 3 parts. The first is a compilation of facts from the state of the art on internal combustion engine fuels and their characteristics and requisites and provides an overview of fuel sources, fuels technology and future projections for availability and alternatives. Part two compiles facts about alcohol chemistry, alcohol identification, production, and use, examines ethanol as spirit and as fuel, and provides an overview of modern evaluation of alcohols as motor fuels and of the characteristics of alcohol fuels. The final section compiles cross references on the handling and combustion of fuels for I.C. engines, presents basic evaluations of events leading to the use of alcohols as motor fuels, reviews current applications of alcohols as motor fuels, describes the formulation of alcohol fuels for engines and engine and fuel handling hardware modifications for using alcohol fuels, and introduces the multifuel engines concept. (LCL)

  4. Study of transient in-cylinder air motion under motoring condition with diesel engine; Diesel engine no motoring ji no tonai ryudo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Kitasei, T; Nakagawa, T [Mitsubishi Motors Co., Tokyo (Japan); Yamazumi, N [Ryoyu Keisan Co., Tokyo (Japan)

    1997-10-01

    The transient in-cylinder air motion have been investigated for reducing exhaust emissions and improving engine performance. A commercial CFD code was used for this purpose. For analyzing under engine motoring condition, the numerical model has a moving piston, intake and exhaust ports with moving valves. As result, exhaust port performance may be analyzed under steady condition, but intake port performance have to be analyzed under unsteady condition. Because transient in-cylinder air motion during intake process is different from steady in-cylinder air motion under influence of piston surface and air viscosity. 4 refs., 11 figs.

  5. The Stirling engine accelerates.; Der Stirling-Motor gibt Gas.

    Energy Technology Data Exchange (ETDEWEB)

    Pfannstiel, Dieter [DiWiTech - Ingenieurpraxis fuer technische und wissenschaftliche Dienstleistungen, Breitenbach a.H. (Germany)

    2010-01-15

    At this moment, Stirling engines are the most outstanding micro technology of combined heat and power generation. The free piston machine combines the principle of the conventional Stirling engine with a modern linear generator for power generation utilizing waste heat for the heating of houses or hot water tanks. All large manufacturers concern themselves with this technology and develop devices based on the Stirling engine. The overview contribution under consideration describes the current level of development of the Stirling devices of different manufacturers. In nearly two years, these devices will serially be produced in the market.

  6. Raley's LNG Truck Site Final Data Report

    Energy Technology Data Exchange (ETDEWEB)

    Battelle

    1999-07-01

    Raley's is a 120-store grocery chain with headquarters in Sacramento, California, that has been operating eight heavy-duty LNG trucks (Kenworth T800 trucks with Cummins L10-300G engines) and two LNG yard tractors (Ottawa trucks with Cummins B5.9G engines) since April 1997. This report describes the results of data collection and evaluation of the eight heavy-duty LNG trucks compared to similar heavy-duty diesel trucks operating at Raley's. The data collection and evaluation are a part of the U.S. Department of Energy (DOE)/National Renewable Energy Laboratory (NREL) Alternative Fuel Truck Evaluation Project.

  7. Sandia and General Motors: Advancing Clean Combustion Engines with

    Science.gov (United States)

    , storage, and disposal. Defense Waste Management Programs Advanced Nuclear Energy Nuclear Energy Safety Components and Systems Improving battery performance, economics, and safety for transportation. Batteries Sciences and Engineering Chemical Sciences Geosciences Fusion Energy Sciences Advanced Scientific Computing

  8. Kogi Truck Culture

    OpenAIRE

    Choy, Vivian

    2011-01-01

    Food trucks have become a large phenomenon in many parts of Southern California. In fact, the University of California, Los Angeles had begun permitting several food trucks to park on campus for hungry students, in response to the closure of the Bombshelter, a major campus food court. These trucks’ budding popularity has been spurred by the notable Kogi Trucks, which began its business serving those in Los Angeles. To explore the heart of this Kogi hype, I took two trips to the intersectio...

  9. Study on MnCl_2/CaCl_2–NH_3 two-stage solid sorption freezing cycle for refrigerated trucks at low engine load in summer

    International Nuclear Information System (INIS)

    Gao, P.; Zhang, X.F.; Wang, L.W.; Wang, R.Z.; Li, D.P.; Liang, Z.W.; Cai, A.F.

    2016-01-01

    Graphical abstract: A MnCl_2/CaCl_2–NH_3 two-stage solid sorption freezing cycle driven by the engine exhaust gas is proposed for refrigerated trucks. - Highlights: • A two-stage adsorption freezing system is designed and constructed for the refrigerated truck. • Composite adsorbents of MnCl_2 and CaCl_2 with the matrix of ENG-TSA are developed. • The average refrigerating capacity of 2.2 kW in the adsorption process is obtained. • The chilled air outlet temperature of the evaporator is controlled at about −5 °C. • The COP is 0.13 when the heating and refrigerating temperatures are 230 °C and −5 °C. - Abstract: A novel MnCl_2/CaCl_2–NH_3 two-stage solid sorption freezing cycle is designed and established for the refrigerated truck with the rated power of 80 kW. The conventional sorption/desorption process and the resorption process are combined in the two-stage cycle. Theoretical analysis shows that such a cycle could adapt to the low heat source temperature and the high cooling temperature of the sorption beds very well, which is quite essential for the truck when the running speed and the load are low in summer. The expanded natural graphite treated with sulfuric acid (ENG-TSA) is chosen as the matrix, and composite adsorbents of MnCl_2/ENG-TSA and CaCl_2/ENG-TSA are developed. The hot air heated by the electric heater is used to simulate the engine exhaust gas to drive the system. When the hot air, the ambient air and the refrigerating temperature are 230 °C, 30 °C and −5 °C, respectively, the average refrigerating capacity is 2.2 kW in the sorption process. Correspondingly, the COP and SCP are 0.13 and 91.7 W/kg, respectively. The average refrigerating capacity of 1.1 kW in one cycle is gotten, which could meet the required refrigerating capacity of the light refrigerated truck at the low engine load engine in summer.

  10. Visualization of flows in a motored rotary combustion engine using holographic interferometry

    Science.gov (United States)

    Hicks, Y. R.; Schock, H. J.; Craig, J. E.; Umstatter, H. L.; Lee, D. Y.

    1986-01-01

    The use of holographic interferometry to view the small- and large-scale flow field structures in the combustion chamber of a motored Wankel engine assembly is described. In order that the flow patterns of interest could be observed, small quantities of helium were injected with the intake air. Variation of the air flow patterns with engine speed, helium flow rate, and rotor position are described. The air flow at two locations within the combustion chamber was examined using this technique.

  11. 78 FR 64394 - Airworthiness Directives; Lycoming Engines and Continental Motors, Inc. Reciprocating Engines

    Science.gov (United States)

    2013-10-29

    ... turbine wheel failure, reduction or complete loss of engine power, loss of engine oil, oil fire, and... after receipt. FOR FURTHER INFORMATION CONTACT: Christopher Richards, Aerospace Engineer, Chicago... failure, reduction or complete loss of engine power, loss of engine oil, oil fire, and damage to the...

  12. 77 FR 72203 - Airworthiness Directives; Lycoming Engines and Continental Motors, Inc. Reciprocating Engines

    Science.gov (United States)

    2012-12-05

    ..., reduction or complete loss of engine power, loss of engine oil, oil fire, and damage to the airplane. DATES... after receipt. FOR FURTHER INFORMATION CONTACT: Christopher Richards, Aerospace Engineer, Chicago... wheel failure, reduction or complete loss of engine power, loss of engine oil, oil fire, and damage to...

  13. 78 FR 48828 - Airworthiness Directives; Continental Motors, Inc. Reciprocating Engines

    Science.gov (United States)

    2013-08-12

    ... cylinder. We identified two independent failure modes resulting in the cylinder head separations; however... cylinders to be $82,620,000. Our cost estimate is exclusive of possible warranty coverage. Authority for... any other maintenance event, or were installed when the engine was modified and are currently...

  14. COOPERATIVE MODE OF ELECTRIC MOTOR AND INTERNAL COMBUSTION ENGINE OPERATION IN THE CONVERSION HYBRID CAR

    Directory of Open Access Journals (Sweden)

    V. Dvadnenko

    2016-12-01

    Full Text Available In the given article the authors proposed a method to control the car, which is converted into a hybrid one. The electric motor and combustion engine operate alternately in the car. They proposed a device for implementing this method and a circuit design for the device in question. They also calculated the dynamics of the vehicle under the joint acceleration.

  15. 46 CFR 11.518 - Service requirements for chief engineer (limited oceans) of steam and/or motor vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Service requirements for chief engineer (limited oceans... Requirements for Engineer Officer § 11.518 Service requirements for chief engineer (limited oceans) of steam... engineer (limited oceans) of steam and/or motor vessels is five years total service in the engineroom of...

  16. 76 FR 63988 - Pilot Project on NAFTA Trucking Provisions; Pre-Authorization Safety Audits

    Science.gov (United States)

    2011-10-14

    ...-0097] Pilot Project on NAFTA Trucking Provisions; Pre-Authorization Safety Audits AGENCY: Federal Motor... motor carriers that applied to participate in the Agency's long-haul pilot program to test and... intent to proceed with the initiation of a United States- Mexico cross-border long-haul trucking pilot...

  17. ProMotor - a technology programme of internal combustion engines; Moottoritekniikan teknologiaohjelma ProMOTOR 1999-2003. Loppuraportti

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    The technology program ProMOTOR, related to the technology of internal combustion engines, covered the whole chain from fuels to engine, and from engine combustion to exhaust gas clean-up. One of the main challenges in the engine sector is to decrease emissions significantly. In order to meet this challenge, the whole chain has to be considered. The program was designed in close cooperation with the national industry of this sector. The main objective of the program was to support product development of the engine- related industry in order to develop and maintain international competitiveness. Corporate projects formed a substantial part of the program, amounting to about 70% of the whole budget volume. Good results were achieved in every sector of the program. In the sector of 'Engine Theory' great efforts were directed to the development of calculation and simulation procedures and protocols. The efforts paid off, and significant progress was achieved. Close international cooperation and academic theses give indication of the high level. In addition to computational work optical method to study incylinder phenomena was developed. Research infrastructure was improved in many different areas. A new research engine, EVE (Extreme Value Engine), makes it possible to vary the operational parameters and the engine process in such ways which are not possible in ordinary engines. A very high boost pressure and freely selectable valve timing are important new features providing more freedom in testing. The mechanical structure of this engine, which is designed for extremely high mean effective pressures, is unique. A research device for piston ring tribology and a large bearing test rig were also designed and constructed for tribology research. The research facilities for work on heavy vehicles and engines improved significantly. Today it is possible to run complete heavy-duty vehicles on a chassis dynamometer and test engines, for example, according to

  18. Liquid sprays and flow studies in the direct-injection diesel engine under motored conditions

    Science.gov (United States)

    Nguyen, Hung Lee; Carpenter, Mark H.; Ramos, Juan I.; Schock, Harold J.; Stegeman, James D.

    1988-01-01

    A two dimensional, implicit finite difference method of the control volume variety, a two equation model of turbulence, and a discrete droplet model were used to study the flow field, turbulence levels, fuel penetration, vaporization, and mixing in diesel engine environments. The model was also used to study the effects of engine speed, injection angle, spray cone angle, droplet distribution, and intake swirl angle on the flow field, spray penetration and vaporization, and turbulence in motored two-stroke diesel engines. It is shown that there are optimum conditions for injection, which depend on droplet distribution, swirl, spray cone angle, and injection angle. The optimum conditions result in good spray penetration and vaporization and in good fuel mixing. The calculation presented clearly indicates that internal combustion engine models can be used to assess, at least qualitatively, the effects of injection characteristics and engine operating conditions on the flow field and on the spray penetration and vaporization in diesel engines.

  19. Engines/motor fuels: possible long-term trends

    Energy Technology Data Exchange (ETDEWEB)

    Bensaid, B.; Gruson, J.F

    2004-07-01

    All energy forecasts for the period between now and 2030 agree: oil should continue to represent 40% share of the world energy balance and oil demand should grow sharply (+60%), driven by the developing countries. In an environment marked by rising world oil consumption, the oil and automobile industries face a major challenge: how to limit the increase in the CO{sub 2} emissions due to road transport by implementing innovative technical solutions with respect to engine technologies and energy sources. (authors)

  20. Engines/motor fuels: possible long-term trends

    International Nuclear Information System (INIS)

    Bensaid, B.; Gruson, J.F.

    2004-01-01

    All energy forecasts for the period between now and 2030 agree: oil should continue to represent 40% share of the world energy balance and oil demand should grow sharply (+60%), driven by the developing countries. In an environment marked by rising world oil consumption, the oil and automobile industries face a major challenge: how to limit the increase in the CO 2 emissions due to road transport by implementing innovative technical solutions with respect to engine technologies and energy sources. (authors)

  1. Effort to increase an engine performance using electrical ignition system for motor vehicle

    Directory of Open Access Journals (Sweden)

    I Wayan Bandem Adnyana

    2012-11-01

    Full Text Available Increasing engine performances using electrical ignition system on motor vehicle. In accordance with the development oftechnology, improvisation of automotive is created in order to increase the performance of engine. The method to increase thisperformance has been done by modify the ignition system, where the conventional method of ignition system which uses contactbreaker substituted by using capacitor. The improvisation of ignition system has been tested by increasing the speed and load onstationary condition. Results show that the improvisation of ignition system by using capacitor increases the effective power andreduce the specific fuel consumption of engine and reduce the gas emission of CO.

  2. Fluid flow and fuel-air mixing in a motored two-dimensional Wankel rotary engine

    Science.gov (United States)

    Shih, T. I.-P.; Nguyen, H. L.; Stegeman, J.

    1986-01-01

    The implicit-factored method of Beam and Warming was employed to obtain numerical solutions to the conservation equations of mass, species, momentum, and energy to study the unsteady, multidimensional flow and mixing of fuel and air inside the combustion chambers of a two-dimensional Wankel rotary engine under motored conditions. The effects of the following engine design and operating parameters on fluid flow and fuel-air mixing during the intake and compression cycles were studied: engine speed, angle of gaseous fuel injection during compression cycle, and speed of the fuel leaving fuel injector.

  3. A study of a direct-injection stratified-charge rotary engine for motor vehicle application

    Science.gov (United States)

    Kagawa, Ryoji; Okazaki, Syunki; Somyo, Nobuhiro; Akagi, Yuji

    1993-03-01

    A study of a direct-injection stratified-charge system (DISC), as applied to a rotary engine (RE) for motor vehicle usage, was undertaken. The goals of this study were improved fuel consumption and reduced exhaust emissions. These goals were thought feasible due to the high thermal efficiency associated with the DISC-RE. This was the first application of this technology to a motor vehicle engine. Stable ignition and ideal stratification systems were developed by means of numerical calculations, air-fuel mixture measurements, and actual engine tests. The use of DISC resulted in significantly improved fuel consumption and reduced exhaust emissions. The use of an exhaust gas recirculating system was studied and found to be beneficial in NOx reduction.

  4. Research on Building Education & Workforce Capacity in Systems Engineering

    Science.gov (United States)

    2011-10-31

    engineered a hybrid vehicle (mail truck) with an electric motor capable of regenerative braking . At other institutions, student teams worked...SPRDE- SE/PSE Competency Model into lower (definitional) or higher (development, deployment) categories of analysis (Sage, 2000, p. 166). For the...entire set of matched responses, statistically significant increases were recorded for all categories of competencies combined, and for categories B

  5. 78 FR 26106 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-05-03

    ... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration (FMCSA). ACTION: Notice; correction. SUMMARY: The FMCSA published a document in the Federal Register of...

  6. 75 FR 22317 - Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety

    Science.gov (United States)

    2010-04-28

    ... 1300 [Docket No. NHTSA-2010-0054] Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety AGENCY: National Highway Traffic Safety Administration (NHTSA), Department of..., multipurpose passenger vehicles, trucks, buses, trailers, incomplete vehicles, motorcycles, and motor vehicle...

  7. Motor Carrier Crash Data -

    Data.gov (United States)

    Department of Transportation — Contains data on large trucks and buses involved in Federally reportable crashes as per Title 49 U.S.C. Part 390.5 (crashes involving a commercial motor vehicle, and...

  8. The Myth - Food Truck

    OpenAIRE

    Otálora Salgado, Esteban

    2015-01-01

    Food truck de comida típica colombiana fusión que espera solucionar la percepción que se tiene acerca de la comida callejera. Para ello, se ha realizado un estudio donde se identifica el problema y se plantea como solución la creación de un food truck que cumpla con todos los estándares de calidad y a su vez innove.

  9. Experimental assessment for instantaneous temperature and heat flux measurements under Diesel motored engine conditions

    International Nuclear Information System (INIS)

    Torregrosa, A.J.; Bermúdez, V.; Olmeda, P.; Fygueroa, O.

    2012-01-01

    Higlights: ► We measured in-cylinder wall heat fluxes. ► We examine the effects of different engine parameters. ► Increasing air mass flow increase heat fluxes. ► The effect of engine speed can be masked by the effect of volumetric efficiency. ► Differences among the different walls have been found. - Abstract: The main goal of this work is to validate an innovative experimental facility and to establish a methodology to evaluate the influence of some of the engine parameters on local engine heat transfer behaviour under motored steady-state conditions. Instantaneous temperature measurements have been performed in order to estimate heat fluxes on a modified Diesel single cylinder combustion chamber. This study was divided into two main parts. The first one was the design and setting on of an experimental bench to reproduce Diesel conditions and perform local-instantaneous temperature measurements along the walls of the combustion chamber by means of fast response thermocouples. The second one was the development of a procedure for temperature signal treatment and local heat flux calculation based on one-dimensional Fourier analysis. A thermodynamic diagnosis model has been employed to characterise the modified engine with the new designed chamber. As a result of the measured data coherent findings have been obtained in order to understand local behaviour of heat transfer in an internal combustion engine, and the influence of engine parameters on local instantaneous temperature and heat flux, have been analysed.

  10. The influence of engine speed and load on the heat transfer between gases and in-cylinder walls at fired and motored conditions of an IDI diesel engine

    International Nuclear Information System (INIS)

    Sanli, Ali; Ozsezen, Ahmet N.; Kilicaslan, Ibrahim; Canakci, Mustafa

    2008-01-01

    In this study, the heat transfer characteristics between gases and in-cylinder walls at fired and motored conditions in a diesel engine were investigated by using engine data obtained experimentally. For this investigation, a four-cylinder, indirect injection (IDI) diesel engine was tested under different engine speeds and loads. The heat transfer coefficient was calculated by using Woschni expression correlated for the IDI diesel engines, and also using Annand and Hohenberg expressions. The temperature of in-cylinder gases were determined from a basic model based on the first law of thermodynamics after measuring in-cylinder pressure experimentally. The results show that the heat transfer characteristics of the IDI diesel engine strongly depend on the engine speed and load as a function of crank angle at fired and motored conditions

  11. The influence of engine speed and load on the heat transfer between gases and in-cylinder walls at fired and motored conditions of an IDI diesel engine

    Energy Technology Data Exchange (ETDEWEB)

    Sanli, Ali; Kilicaslan, Ibrahim [Department of Mechanical Education, Kocaeli University, 41380 Izmit (Turkey); Ozsezen, Ahmet N.; Canakci, Mustafa [Department of Mechanical Education, Kocaeli University, 41380 Izmit (Turkey); Alternative Fuels R and D Center, Kocaeli University, 41040 Izmit (Turkey)

    2008-08-15

    In this study, the heat transfer characteristics between gases and in-cylinder walls at fired and motored conditions in a diesel engine were investigated by using engine data obtained experimentally. For this investigation, a four-cylinder, indirect injection (IDI) diesel engine was tested under different engine speeds and loads. The heat transfer coefficient was calculated by using Woschni expression correlated for the IDI diesel engines, and also using Annand and Hohenberg expressions. The temperature of in-cylinder gases were determined from a basic model based on the first law of thermodynamics after measuring in-cylinder pressure experimentally. The results show that the heat transfer characteristics of the IDI diesel engine strongly depend on the engine speed and load as a function of crank angle at fired and motored conditions. (author)

  12. Enhancements to the Idaho National Engineering Laboratory motor-operated valve assessment software

    International Nuclear Information System (INIS)

    Holbrook, M.R.; Watkins, J.C.

    1994-01-01

    In January 1991, the U.S. Nuclear Regulatory Commission (USNRC) commenced Part 1 inspections to review licensee's motor-operated valve (MOV) programs that were developed to address Generic Letter 89-10, open-quotes Safety-Related Motor-Operated Valve Testing and Surveillanceclose quotes. In support, of this effort, the Isolation Valve Assessment (IVA) software, Version 3.10, was developed by the Idaho National Engineering Laboratory (INEL) to enable rapid in-depth review of MOV sizing and torque switch setting calculations. In 1994, the USNRC commenced Part 2 inspections, which involve a more in-depth review of MOV in situ testing relative to design-basis assumptions. The purpose of this paper is to describe the latest INEL and industry research that has been incorporated into Version 4.00 of the IVA software to support the latest round of inspections. Major improvements include (a) using dynamic and static test results to determine MOV performance parameters and validate design-basis engineering assumptions, (b) determining the stem/stem-nut coefficient of friction using new research-based techniques, (c) adding the ability to evaluate globe valves, and (d) incorporating new methods to account for the effects of high ambient temperature on the output torque of alternating current (ac) motors

  13. Three-dimensional simulation of a novel rotary-piston engine in the motoring mode

    Directory of Open Access Journals (Sweden)

    Mohammadreza Khani

    2017-09-01

    Full Text Available In this simulation study, the flow and thermal characteristics of a novel rotary-piston engine, which is a kind of internal combustion engines, were investigated by computational fluid dynamics and the finite volume method. The structure of this engine is different to others, mainly for having 24 cylinders during the motoring mode. As a novel engine, creation of numerical models based on Reynolds average Navier Stokes (RANS simulation and analysis of various speed engines on the flow and thermal fields during intake and compression strokes are the focus of this work. The results were illustrated in term of the streamline patterns, in-cylinder temperature and pressure profile, swirl ratio (SR, wall heat flux, and turbulent velocity fluctuation. The present study indicates that, the mean pressure, temperature trace, and heat loss from the wall increase when switching to a higher engine speed. The temperature distribution reveals that the maximum temperature is restricted in the center of the combustion chamber near top dead center (TDC. Also, the maximum amount of turbulent velocity and swirl ratio are achieved at the beginning of the intake stroke and near TDC. It is observed that the obtained numerical results are in general agreement with the available experimental data.

  14. 76 FR 5586 - California State Motor Vehicle and Nonroad Engine Pollution Control Standards; Mobile Cargo...

    Science.gov (United States)

    2011-02-01

    ... requirements are designed to use best available control technologies to reduce public exposure to emissions of...-use yard trucks to meet BACT performance standards primarily through accelerated turnover of older...

  15. UPS CNG Truck Fleet Start Up Experience: Alternative Fuel Truck Evaluation Project

    International Nuclear Information System (INIS)

    Walkowicz, K.

    2001-01-01

    UPS operates 140 Freightliner Custom Chassis compressed natural gas (CNG)-powered vehicles with Cummins B5.9G engines. Fifteen are participating in the Alternative Fuel Truck Evaluation Project being funded by DOE's Office of Transportation Technologies and the Office of Heavy Vehicle Technologies

  16. Active Suspension of Truck Seat

    Directory of Open Access Journals (Sweden)

    Masaaki Kawana

    1998-01-01

    Full Text Available The driver’s seat of a heavy duty truck is usually mounted on a spring–damper assembly anchored to the cab floor. To improve riding comfort, this study investigated the effects of mounting a computer-controlled actuator in parallel with the traditional spring–damper assembly. A dynamic model of the seat is represented by a two degree-of-freedom system, including a cushion. In this paper, a control system is designed, using optimal control theory, which minimizes rms vertical acceleration at a point representing the driver’s hip point. In this system, accelerations of the hip point, the seat frame and the cab floor are picked up and integrated to obtain the state variables to be fed back and fed forward to the actuator through a digital computer. The actuator is constructed with electric servo-motor and ball-screw mechanism. The experimental study was carried out on a shaker, which simulates the vibrations of the cab floor in actual service. Results were obtained for both a dummy and a real human body. The vibration test produced rms accelerations of the seat and the hip point of about 1.0 m/s2 without the actuator, while the rms accelerations were suppressed to about 0.5 m/s2 at a rms input voltage to the servo-motor of 1.0 V.

  17. Experimental Investigation of Sulfuric Acid Condensation and Corrosion Rate in Motored Bukh DV24 Diesel Engine

    DEFF Research Database (Denmark)

    Kjemtrup, Lars; Cordtz, Rasmus Faurskov; Meyer, Martin

    2017-01-01

    The work conducted in this paper presents a novel experimental setup to study sulfuric acid cold corrosion of cylinder liners in large two-stroke marine diesel engines. The process is simulated in a motored light duty BUKH DV24 diesel engine where the charge air contain known amounts of H2SO4 and H......2O vapor. Liner corrosion is measured as iron accumulation in the lubeoil. Similarly sulfuric acid condensation is assessed by measuring the accumulation of sulfur in the lube oil. To clarify the corrosive effect of sulfuric acid the lube oil utilized for experiments is a sulfur free neutral oil...... without alkaline additives (Chevron Neutral Oil 600R). Iron and sulfur accumulation in the lube oil is analyzed withan Energy Dispersive X-Ray Fluorescence (ED-XRF) apparatus. Three test cases with different H2SO4 concentrations are run. Results reveal good agreement between sulfuric acid injection flow...

  18. The Aerodynamics of Heavy Vehicles III : Trucks, Buses and Trains

    CERN Document Server

    Orellano, Alexander

    2016-01-01

    This volume contains papers presented at the International conference “The Aerodynamics of Heavy Vehicles III: Trucks, Buses and Trains” held in Potsdam, Germany, September 12-17, 2010 by Engineering Conferences International (ECI). Leading scientists and engineers from industry, universities and research laboratories, including truck and high-speed train manufacturers and operators were brought together to discuss computer simulation and experimental techniques to be applied for the design of more efficient trucks, buses and high-speed trains in the future.   This conference was the third in the series after Monterey-Pacific Groove in 2002 and Lake Tahoe in 2007.  The presentations address different aspects of train aerodynamics (cross wind effects, underbody flow, tunnel aerodynamics and aeroacoustics, experimental techniques), truck aerodynamics (drag reduction, flow control, experimental and computational techniques) as well as computational fluid dynamics and bluff body, wake and jet flows.

  19. Truckstop - and Truck - Electrification

    International Nuclear Information System (INIS)

    Skip Yeakel

    2001-01-01

    The conclusions of this paper are: 0.5-1.5 G/H and/or BUSG/Y-how much time and money will it take to quantify and WHY BOTHER TO DO SO? No shortage of things to do re truckstop-+ truck - electrification; Better that government and industry should put many eggs in lots of baskets vs. all in one or few; Best concepts will surface as most viable; Economic appeal better than regulation or brute force; Launch Ground Freight Partnership and give it a chance to work; Demonstration is an effective means to educate, and learn from, customers-learning is a two way street; Research, Development, Demonstration, and Deployment (RD 3) are all important but only deployment gets results; TSE can start small in numbers of spaces to accommodate economically inspired growth but upfront plans should be made for expansion if meaningful idle reduction is to follow via TE; 110VAC 15A service/ parking space is minimal-if infrastructure starts like this, upfront plans must be made to increase capacity; Increased electrification of truckstop and truck alike will result in much better life on the road; Improved sleep will improve driver alertness and safety; Reduced idling will significantly reduce fuel use and emissions; Universal appeal for DOD, DOE, DOT, EPA, OEMs, and users alike; Clean coal, gas, hydro, nuclear, or wind energy sources are all distinctly American means by which to generate electricity; Nothing can compete with diesel fuel to serve mobile truck needs; stationary trucks are like power plants-they don't move and should NOT be powered by petroleum products whenever possible; Use American fueled power plants-electricity-to serve truck idling needs wherever practical to do so; encourage economic aspect; Create and reward industry initiatives to reduce fuel use; Eliminate FET on new trucks, provide tax credits (non highway fuel use and investment), provide incentives based on results; Encourage newer/ cleaner truck use; solicit BAAs with mandatory OEM/ fleet participation/ lead

  20. Using 3D Multi-Body Simulation to Evaluate Future Truck Technologies

    National Research Council Canada - National Science Library

    Gunter, Dave; Bylsma, Wes; Letherwood, Mike; Dennis, Stacey; Argeropoulos, Kris; Teschendorf, Dan; Gorsich, Dave

    2004-01-01

    ... steering, and in-hub electric drive motors. Fully three-dimensional Future Truck models were created using a commercially available modeling and simulation methodology and limited validation studies were performed by comparing model...

  1. Transformation of a car diesel engine with direct injection and common rail into a dual fuel engine; Trasformazione di un motore automobilistico diesel ad iniezione diretta dotato di common rail in un motore dual fuel

    Energy Technology Data Exchange (ETDEWEB)

    De Risi, A.; Laforgia, D. [Lecce Univ. (Italy). Dipt. di Scienza dei Materiali

    1999-08-01

    The reduced polluting emissions make natural gas a quite interesting alternative fuel for automotive applications. Therefore a car diesel engine has been transformed into a dual fuel engine with pilot injection via the common rail injection system used to ignite the methane-air charge. Standard injection pumps show a certain instability at low flow rates and high engine speed. On the opposite the new common rail system allows to ignite the fuel in all conditions with an amount of gas oil less than 8% of the entire energy required by the engine was enough to ignite the fuel. Furthermore, a power increase has been obtained, with an overall efficiency equal to or even higher than a conventional engine. The article deals with a series of test carried out on 1929 cm{sup 3} direct injection turbo-charged engine and presents the preliminary results. [Italian] La riduzione delle emissioni inquinanti rende il metano un combustibile alternativo piuttosto interessante per applicazioni automobilistiche. Per quasta ragione e' stata realizzata la trasformazione di un motore automobilitico diesel ad iniezione diretta in un motore dual fuel con iniezione pilota prodotta da un sistema common rail. L'adozione del sistema common rail consente l'accensione in ogni condizione con una quantita' di combustibile inferiore all'8% dell'intera energia richiesta alla potenza nominale del motore risolvendo i problemi di instabilita' che una pompa normale presenta a basse portate e ad alta velocita'. In alcuni casi e' stato sufficiente il 3% dell'energia totale richiesta dal motore per accendere la carica. Inoltre si e' ottenuto un aumento della potenza con un'efficienza globale analoga a qualla del motore tradizionale o addirittura migliore. Si riportano i risultati di una campagna di prove condotta su un motore sovralimentato ad iniezione diretta (1929 cm{sup 3}).

  2. Space Launch System Base Heating Test: Sub-Scale Rocket Engine/Motor Design, Development & Performance Analysis

    Science.gov (United States)

    Mehta, Manish; Seaford, Mark; Kovarik, Brian; Dufrene, Aaron; Solly, Nathan

    2014-01-01

    ATA-002 Technical Team has successfully designed, developed, tested and assessed the SLS Pathfinder propulsion systems for the Main Base Heating Test Program. Major Outcomes of the Pathfinder Test Program: Reach 90% of full-scale chamber pressure Achieved all engine/motor design parameter requirements Reach steady plume flow behavior in less than 35 msec Steady chamber pressure for 60 to 100 msec during engine/motor operation Similar model engine/motor performance to full-scale SLS system Mitigated nozzle throat and combustor thermal erosion Test data shows good agreement with numerical prediction codes Next phase of the ATA-002 Test Program Design & development of the SLS OML for the Main Base Heating Test Tweak BSRM design to optimize performance Tweak CS-REM design to increase robustness MSFC Aerosciences and CUBRC have the capability to develop sub-scale propulsion systems to meet desired performance requirements for short-duration testing.

  3. Iowa truck information guide.

    Science.gov (United States)

    2011-07-22

    The Iowa Department of Transportation and the offices of Motor : Vehicle Enforcement, Motor Carrier Services, Vehicle Services, : and Driver Services want to make your travels into and through : our state safer, legal and less complicated. : This boo...

  4. Vieweg manual of motor car engineering. 3. tot. new rev. and enl. ed.; Vieweg Handbuch Kraftfahrzeugtechnik

    Energy Technology Data Exchange (ETDEWEB)

    Braess, H.H.; Seiffert, U. (eds.)

    2003-07-01

    This is the 3rd, revised and re-edited edition. Current trends are considered, i.e. DI and variable valve operation, particulate filters, double clutch gears, ESP-Plus, SUN-Fuel, and variable adaptive lighting. There are new chapters on standardisation (e.g. telematics and interface problems), accident research, internals, software, service-friendly design, maintenance and diagnosis, as well as sports and racing cars. Contents: Requirements on motor cars; Innovative technologies; Aerodynamics; Air conditioning; Acoustics; Design; Package; Fuel cell; Electric vehicles; Gas turbine; Spark ignition engine; Diesel engine; Superchargers; Couplings and gears; Four-wheel drives; Brakes and control systems; Two-stroke engines; Car bodies; Materials; Surface protection; Passenger compartment; Safety; Brakes; Tyres; Chassis; Fuels; Electric and electronic systems; Software; Driver assistant systems; Lighting; Sensors; Onboard network; EMP; Materials; Simultaneous engineering; Simulations; Experimental technologies; Motor cars and transportation in the future; Legislation and standardisation; Accident research; Diagnosis and maintenance; Racing cars and sports cars. [German] Fahrzeugingenieure in Praxis und Ausbildung benoetigen den raschen und sicheren Zugriff auf Grundlagen und Details der Fahrzeugtechnik sowie wesentliche zugehoerige industrielle Prozesse. Solche Informationen, die in ganz unterschiedlichen Quellen abgelegt sind, systematisch und bewertend zusammenzufuehren, hat sich dieses Handbuch zum Ziel gesetzt. Die Autoren sind bedeutende Fachleute der deutschen Automobil- und Zuliefererindustrie, sie stellen sicher, dass Theorie und Praxis vernetzt vermittelt werden. Die dritte Auflage wurde neu bearbeitet, aktualisiert und erweitert. Damit haben die aktuellen Entwicklungen von Benzindirekteinspritzung und variabler Ventilbetrieb, sowie Partikelfilter, Doppelkupplungsgetriebe, ESP-Plus, SUN-Fuel oder variable adaptive Beleuchtungssysteme Eingang gefunden. Neu

  5. ANFO truck burn trials

    Energy Technology Data Exchange (ETDEWEB)

    Rosen von, B.; Contestabile, E. [Natural Resources Canada, CANMET Canadian Explosives Research Laboratory, Ottawa, ON (Canada)

    2003-10-01

    This report describes the investigation of a tractor-trailer explosion. A truck loaded with 18,000 kg of commercial explosives, of which 13,000 kg was ammonium nitrate with fuel oil (ANFO), caught fire when it struck a rockcut near Walden, Ontario on August 5, 1998. The fire resulted in the detonation of the load. The Canadian Explosives Research Laboratory (CERL) conducted a test program to examine the suitability of existing explosive transportation regulations. Unconfined burns of ANFO were performed. The accident was recreated in two burn trials in an attempt to identify the mechanism that led from fire to detonation. Two full-scale tests were conducted using complete tractor-trailers, each in a jack-knifed position with most of the explosives placed on the ground in front of the trailer. ANFO was used in the first test to determine its response to thermal stimulus and the likelihood of detonation or explosion. The second test involved ANFO, a slurry and an emulsion. Thermocouples and video cameras were used to observe the burning characteristics of the explosives, the truck and its components. The explosives burned steadily for 80 minutes in each test. Many truck components, such as tires, spring brake chambers and the fuel tank ruptured violently due to the heat. Although no detonation occurred in the test trials, it was concluded that under favourable conditions, many truck components, might produce fragments with enough energy to initiate heat-sensitized explosives. It was suggested that a fragment impact caused the detonation at Walden. 4 refs., 7 tabs., 8 figs.

  6. 77 FR 20480 - Volvo Trucks North America and Mack Trucks, Inc., Grant of Petition for Decision of...

    Science.gov (United States)

    2012-04-04

    ... GU model trucks that were built with certain Meritor WABCO Vehicle Control Systems (Meritor WABCO... equipment requirements for motor vehicles equipped with air brake systems. Paragraph S5.3.4.1(a) of FMVSS No... vehicle's braking performance. The tests and analyses were performed by an independent test lab, Link...

  7. Idle emissions from medium heavy-duty diesel and gasoline trucks.

    Science.gov (United States)

    Khan, A B M S; Clark, Nigel N; Gautam, Mridul; Wayne, W Scott; Thompson, Gregory J; Lyons, Donald W

    2009-03-01

    Idle emissions data from 19 medium heavy-duty diesel and gasoline trucks are presented in this paper. Emissions from these trucks were characterized using full-flow exhaust dilution as part of the Coordinating Research Council (CRC) Project E-55/59. Idle emissions data were not available from dedicated measurements, but were extracted from the continuous emissions data on the low-speed transient mode of the medium heavy-duty truck (MHDTLO) cycle. The four gasoline trucks produced very low oxides of nitrogen (NOx) and negligible particulate matter (PM) during idle. However, carbon monoxide (CO) and hydrocarbons (HCs) from these four trucks were approximately 285 and 153 g/hr on average, respectively. The gasoline trucks consumed substantially more fuel at an hourly rate (0.84 gal/hr) than their diesel counterparts (0.44 gal/hr) during idling. The diesel trucks, on the other hand, emitted higher NOx (79 g/hr) and comparatively higher PM (4.1 g/hr), on average, than the gasoline trucks (3.8 g/hr of NOx and 0.9 g/hr of PM, on average). Idle NOx emissions from diesel trucks were high for post-1992 model year engines, but no trends were observed for fuel consumption. Idle emissions and fuel consumption from the medium heavy-duty diesel trucks (MHDDTs) were marginally lower than those from the heavy heavy-duty diesel trucks (HHDDTs), previously reported in the literature.

  8. Vehicle test report: Battronic pickup truck

    Science.gov (United States)

    Price, T. W.; Shain, T. W.; Freeman, R. J.; Pompa, M. F.

    1982-01-01

    An electric pickup truck was tested to characterize certain parameters and to provide baseline data that can be used for the comparison of improved batteries that may be incorporated into the vehicle at a later time. The vehicle tests were concentrated on the electrical drive subsystem; i.e., the batteries, controller, and motor. The tests included coastdowns to characterize the road load and range evaluations for both cyclic and constant speed conditions. A qualitative evaluation of the vehicle's performance was made by comparing its constant speed range performance with other vehicles.

  9. Laser-Doppler velocimetry measurements in a motored IC engine simulator

    Science.gov (United States)

    Gany, A.; Sirignano, W. A.; Larrea, J.-J.

    1980-01-01

    A measurement technique and experimental results are presented for mean velocity and velocity fluctuations in a motored, axisymmetric engine chamber simulation. Three valve configurations are considered: open orifice, open valve, and operating valve. Measurements of axial and tangential velocity components have been taken at various axial and radial positions for one compression ratio (7:1) and one rpm level (31). The measurements show that the intake stroke (in both two and four stroke operations) result in a recirculating flow with substantial turbulence generation even at the low rpm value. The four-stroke results in an axisymmetric design are novel and especially significant since the ability exists to make comparisons with theoretical, axisymmetric, turbulent results.

  10. Optimization of Interior Permanent Magnet Motor by Quality Engineering and Multivariate Analysis

    Science.gov (United States)

    Okada, Yukihiro; Kawase, Yoshihiro

    This paper has described the method of optimization based on the finite element method. The quality engineering and the multivariable analysis are used as the optimization technique. This optimizing method consists of two steps. At Step.1, the influence of parameters for output is obtained quantitatively, at Step.2, the number of calculation by the FEM can be cut down. That is, the optimal combination of the design parameters, which satisfies the required characteristic, can be searched for efficiently. In addition, this method is applied to a design of IPM motor to reduce the torque ripple. The final shape can maintain average torque and cut down the torque ripple 65%. Furthermore, the amount of permanent magnets can be reduced.

  11. Particles and emissions from a diesel engine equipped with a humid air motor system

    Energy Technology Data Exchange (ETDEWEB)

    Nord, Kent; Zurita, Grover; Tingvall, Bror; Haupt, Dan [Luleaa Univ. of Technology (Sweden). Div. of Environmental Technology

    2002-02-01

    A system for reduction of NO{sub x}, humid air motor system (HAM), has been connected to an eleven liters diesel engine. Earlier studies have demonstrated the system's capacity to lower NO{sub x}-emissions from diesel engines. The present study is directed to investigate their influence of the system on the emissions of particles, aldehydes and noise while at the same time monitoring essential engine parameters, water consumption and verifying the NO{sub x} reducing ability. The system has been tested under the various conditions stated in 13-mode cycle ECE R-49. Additional tests have been necessary for sampling and measurements of particles and noise. The results show that HAM caused a large reduction of the NO{sub x} emissions while the engine performance was almost unaffected. Average reduction of NO{sub x} during the different modes of ECE R-49 was 51,1%. The reduction was directly related to the humidity of the inlet air and a further reduction can be anticipated with higher humidity. Samples have also been taken for acetaldehydes and formaldehyde. The results suggest a large reduction of aldehydes, in the range of 78 to 100%, when using HAM. Unfortunately it cannot be excluded that the results obtained are a result of a combination of high air humidity and the sampling technique used. The influence of the system on the emission of hydrocarbons was negligible while a moderate increase in the emission of carbon monoxide was noticed. No confident relationship between air humidity and the observed effects could be detected. Particle number concentrations and size distribution have also been measured. The measurements showed that the particle number concentrations was usually increased when HAM was coupled to the engine. The increase in particle number concentration, observed in five out of six running modes, varied between 46 and 148%. There was no trend indicating a shift in mean particle diameter when using HAM. Noise level and cylinder pressure have also

  12. Vehicle to vehicle communications for trucks.

    Science.gov (United States)

    2014-01-01

    The trucking industry is a critical component of American commerce. The American : Trucking Association estimates that over 80 percent of U.S. communities depend : exclusively on trucking for delivery of their goods and commodities

  13. Mitigating Wind Induced Truck Crashes

    Science.gov (United States)

    2009-12-25

    Dangerous weather and high wind in particular, is a common contributing factor in truck crashes. High wind speeds have been documented as a perennial cause of truck crashes in Kansas and other Great Plains states. The possibility of reducing such cra...

  14. Simulated Fuel Economy and Emissions Performance during City and Interstate Driving for a Heavy-Duty Hybrid Truck

    Energy Technology Data Exchange (ETDEWEB)

    Daw, C. Stuart; Gao, Zhiming; Smith, David E.; Laclair, Tim J.; Pihl, Josh A.; Edwards, K. Dean

    2013-04-08

    We compare simulated fuel economy and emissions for both conventional and hybrid class 8 heavy-duty diesel trucks operating over multiple urban and highway driving cycles. Both light and heavy freight loads were considered, and all simulations included full aftertreatment for NOx and particulate emissions controls. The aftertreatment components included a diesel oxidation catalyst (DOC), urea-selective catalytic NOx reduction (SCR), and a catalyzed diesel particulate filter (DPF). Our simulated hybrid powertrain was configured with a pre-transmission parallel drive, with a single electric motor between the clutch and gearbox. A conventional HD truck with equivalent diesel engine and aftertreatment was also simulated for comparison. Our results indicate that hybridization can significantly increase HD fuel economy and improve emissions control in city driving. However, there is less potential hybridization benefit for HD highway driving. A major factor behind the reduced hybridization benefit for highway driving is that there are fewer opportunities to utilize regenerative breaking. Our aftertreatment simulations indicate that opportunities for passive DPF regeneration are much greater for both hybrid and conventional trucks during highway driving due to higher sustained exhaust temperatures. When passive DPF regeneration is extensively utilized, the fuel penalty for particulate control is virtually eliminated, except for the 0.4%-0.9% fuel penalty associated with the slightly higher exhaust backpressure.

  15. Development of Servo Motor Trainer for Basic Control System in Laboratory of Electrical Engineering Control System Faculty of Engineering Universitas Negeri Surabaya

    Science.gov (United States)

    Endryansyah; Wanarti Rusimamto, Puput; Ridianto, Adam; Sugiarto, Hariyadi

    2018-04-01

    In the Department of Electrical Engineering FT Unesa, there are 3 majors: S1 Electrical Engineering Education, S1 Electrical Engineering, and D3 Electrical Engineering. Courses the Basic System Settings go to in the curriculum of the three programs. Team lecturer college of basic system settings seek learning innovation, focused on the development of trainer to student practicum at the laboratory of systems control. Trainer developed is a servo motor along with the lab module that contains a wide variety of theories about the servo motor and guide the practicum. This research type is development research using methods Research & development (R & D). In which the steps are applied in this study is as follows: pay attention to the potential and existing problems, gather information and study the literature, design the product, validate the design, revise the design, a limited trial. The results of the validation of learning device in the form of modules and trainer obtained as follows: score validation of learning device is 3,64; score validation lab module Servo Motor is 3,47; and questionnaire responses of students is 3,73. The result of the whole validation value is located in the interval >of 3.25 s/d 4 with the category of “Very Valid”, so it can be concluded that all instruments have a level of validity “Very Valid” and worthy of use for further learning.

  16. The numerical assessment of motion strategies for integrated linear motor during starting of a free-piston engine generator

    Science.gov (United States)

    Razali Hanipah, M.; Razul Razali, Akhtar

    2017-10-01

    Free-piston engine generator (FPEG) provides a novel method for electrical power generation in hybrid electric vehicle applications with scarcely reported prototype development and testing. This paper is looking into the motion control strategy for motoring the FPEG during starting. There are two motion profiles investigated namely, trapezoidal velocity and Scurve velocity. Both motion profiles were investigated numerically and the results have shown that the S-curve motion can only achieve 80% of the stroke when operated at the proposed motoring speed of 10Hz.

  17. Alternative-fueled truck demonstration natural gas program: Caterpillar G3406LE development and demonstration

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    In 1990, the California Energy Commission, the South Coast Air Quality Management District, and the Southern California Gas Company joined together to sponsor the development and demonstration of compressed natural gas engines for Class 8 heavy-duty line-haul trucking applications. This program became part of an overall Alternative-Fueled Truck Demonstration Program, with the goal of advancing the technological development of alternative-fueled engines. The demonstration showed natural gas to be a technically viable fuel for Class 8 truck engines.

  18. Effects of Surface Irregularities on Piston Ring-Cylinder Tribo Pair of a Two Stroke Motor Engine in Hydrodynamic Lubrication

    Directory of Open Access Journals (Sweden)

    A. Zavos

    2015-03-01

    Full Text Available Tribological parameters such as friction, lubrication and wear influence strongly the engine component's life. In this study, a piston ring-cylinder system simulated taking into account the surface modifications under fully flooded lubrication and normal engine conditions. The hydrodynamic pressure field solved based on the Navier Stokes equations by Fluid Structure Interaction analysis. A real experimental data of piston ring-cylinder was used from a two stroke motor engine 50 cc. The surface irregularities are measured by 3D coordinate measurement machine while the engine has been worked about 4000 hours. The friction force, the hydrodynamic pressure, the oil film and the mechanical stresses were predicted for different engine conditions. Results show that the worn profile ring reduces the friction as well as the mechanical stresses increased. Surface condition of worn top ring was observed after a metallurgical profile analysis.

  19. The analysis of loading losses from tank trucks

    Directory of Open Access Journals (Sweden)

    Jovanović Ana P.

    2006-01-01

    Full Text Available The quantity of loading losses, which are the primary source of evaporative emissions from tank cars and trucks was analyzed in this paper. Loading losses occur as organic vapors in "empty" cargo tanks are displaced to the atmosphere by the liquid being loaded into the tanks. Emissions from loading petroleum liquid were estimated using three methods: the API (American Petroleum Institute method, the VDI (Verein Deutscher Ingenieure -Association of German Engineers method and the Yugoslav Standard JUS B.HO.531 method. The mass of evaporative losses from loading operations is a function of the following parameters: the method of loading the cargo, the physical and chemical characteristics of the cargo and the ambient temperature during loading. Evaporation losses from the loading of motor gasoline (MB-95, BMB-95, MB-98 and MB-86 and diesel fuels (D-2, Euro D-2 were calculated. Losses on a monthly and annual basis were presented for an assumed amount of loaded cargo. It was estimated that the highest loading losses occur in the summer period because of high ambient daily temperatures and in the period of higher transporting levels. It should be pointed out that the loading losses of diesel fuel calculated using an empirical coefficient according to JUS B.HO.531 are significantly higher in comparison with the loading losses calculated using emission factors from the EPA and the VDI method. The gasoline loading losses calculated using emission factors derived from the three methods are similar.

  20. Medium Truck Duty Cycle Data from Real-World Driving Environments: Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Lascurain, Mary Beth [ORNL; Franzese, Oscar [ORNL; Capps, Gary J [ORNL; Siekmann, Adam [ORNL; Thomas, Neil [ORNL; LaClair, Tim J [ORNL; Barker, Alan M [ORNL; Knee, Helmut E [ORNL

    2012-11-01

    Since the early part of the 20th century, the US trucking industry has provided a safe and economical means of moving commodities across the country. At present, nearly 80% of US domestic freight movement involves the use of trucks. The US Department of Energy (DOE) is spearheading a number of research efforts to improve heavy vehicle fuel efficiencies. This includes research in engine technologies (including hybrid and fuel cell technologies), lightweight materials, advanced fuels, and parasitic loss reductions. In addition, DOE is developing advanced tools and models to support heavy vehicle research and is leading the 21st Century Truck Partnership and the SuperTruck development effort. Both of these efforts have the common goal of decreasing the fuel consumption of heavy vehicles. In the case of SuperTruck, a goal of improving the overall freight efficiency of a combination tractor-trailer has been established. This Medium Truck Duty Cycle (MTDC) project is a critical element in DOE s vision for improved heavy vehicle energy efficiency; it is unique in that there is no other existing national database of characteristic duty cycles for medium trucks based on collecting data from Class 6 and 7 vehicles. It involves the collection of real-world data on medium trucks for various situational characteristics (e.g., rural/urban, freeway/arterial, congested/free-flowing, good/bad weather) and looks at the unique nature of medium trucks drive cycles (stop-and-go delivery, power takeoff, idle time, short-radius trips). This research provides a rich source of data that can contribute to the development of new tools for FE and modeling, provide DOE a sound basis upon which to make technology investment decisions, and provide a national archive of real-world-based medium-truck operational data to support energy efficiency research. The MTDC project involved a two-part field operational test (FOT). For the Part-1 FOT, three vehicles each from two vocations (urban transit and

  1. Engineering of a novel Ca2+-regulated kinesin molecular motor using a calmodulin dimer linker

    International Nuclear Information System (INIS)

    Shishido, Hideki; Maruta, Shinsaku

    2012-01-01

    Highlights: ► Engineered kinesin–M13 and calmodulin involving single cysteine were prepared. ► CaM mutant was cross-linked to dimer by bifunctional thiol reactive reagent. ► Kinesin–M13 was dimerized via CaM dimer in the presence of calcium. ► Function of the engineered kinesin was regulated by a Ca 2+ -calmodulin dimer linker. -- Abstract: The kinesin–microtubule system holds great promise as a molecular shuttle device within biochips. However, one current barrier is that such shuttles do not have “on–off” control of their movement. Here we report the development of a novel molecular motor powered by an accelerator and brake system, using a kinesin monomer and a calmodulin (CaM) dimer. The kinesin monomer, K355, was fused with a CaM target peptide (M13 peptide) at the C-terminal part of the neck region (K355–M13). We also prepared CaM dimers using CaM mutants (Q3C), (R86C), or (A147C) and crosslinkers that react with cysteine residues. Following induction of K355–M13 dimerization with CaM dimers, we measured K355–M13 motility and found that it can be reversibly regulated in a Ca 2+ -dependent manner. We also found that velocities of K355–M13 varied depending on the type and crosslink position of the CaM dimer used; crosslink length also had a moderate effect on motility. These results suggest Ca 2+ -dependent dimerization of K355–M13 could be used as a novel molecular shuttle, equipped with an accelerator and brake system, for biochip applications.

  2. Truck shovel users group

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, J. [Surface Mining Association for Research and Technology, AB (Canada)

    2008-07-01

    The Truck Shovel Users Group (TSUG) was developed as part of the Surface Mining Association for Research and Technology (SMART), an association of companies that meet to coordinate technology developments for the mining industry. The TSUG meet regularly to discuss equipment upgrades, maintenance planning systems, and repair techniques. The group strives to maximize the value of its assets through increased safety, equipment performance and productivity. This presentation provided administrative details about the TSUG including contact details and admission costs. It was concluded that members of the group must be employed by companies that use heavy mining equipment, and must also be willing to host meetings, make presentations, and support the common goals of the group. tabs., figs.

  3. Acceptance test report for core sample trucks 3 and 4

    International Nuclear Information System (INIS)

    Corbett, J.E.

    1996-01-01

    The purpose of this Acceptance Test Report is to provide documentation for the acceptance testing of the rotary mode core sample trucks 3 and 4, designated as HO-68K-4600 and HO-68K-4647, respectively. This report conforms to the guidelines established in WHC-IP-1026, ''Engineering Practice Guidelines,'' Appendix M, ''Acceptance Test Procedures and Reports.'' Rotary mode core sample trucks 3 and 4 were based upon the design of the second core sample truck (HO-68K-4345) which was constructed to implement rotary mode sampling of the waste tanks at Hanford. Successful completion of acceptance testing on June 30, 1995 verified that all design requirements were met. This report is divided into four sections, beginning with general information. Acceptance testing was performed on trucks 3 and 4 during the months of March through June, 1995. All testing was performed at the ''Rock Slinger'' test site in the 200 West area. The sequence of testing was determined by equipment availability, and the initial revision of the Acceptance Test Procedure (ATP) was used for both trucks. Testing was directed by ICF-KH, with the support of WHC Characterization Equipment Engineering and Characterization Project Operations. Testing was completed per the ATP without discrepancies or deviations, except as noted

  4. 49 CFR 399.207 - Truck and truck-tractor access requirements.

    Science.gov (United States)

    2010-10-01

    .... Exception. If air and electrical connections necessary to couple or uncouple a truck-tractor from a trailer... 49 Transportation 5 2010-10-01 2010-10-01 false Truck and truck-tractor access requirements. 399... Vehicles § 399.207 Truck and truck-tractor access requirements. (a) General rule. Any person entering or...

  5. Analysis of Engine Propeller Matching of DC Motor as a Main Propulsion

    Directory of Open Access Journals (Sweden)

    Eddy Setyo Koenhardono

    2017-12-01

    Full Text Available The development of ship always searches through the most benefits system for reducing costs of propulsion system without increase pollution. Diesel propulsion system or also known as conventional propulsion system is efficient but requires high operating costs and increase high level of marine pollution. Electrical propulsion system is using electric motors as the prime mover of the propeller. There are 2 types of electric motors that will be used for research of electric propulsion system, there are; DC motors and three-phases induction motor. As the use of DC motor as a prime mover for this electrical propulsion system, this study determines the characteristic between voltage terminal with torque and also field current with torque. It results that torque produced by the DC motor is in the same magnitude with the speed (RPM. The higher the speed have shaped the value of the torque. The input and terminal voltages adjusts all variables and results. In this study, different field voltage creates different pattern of motor envelope. Its manner to propeller curve occurs total different results. With field voltage of 50 V, the ranges of motor envelope immoveable in the point of 150% of present speed and 160%. While field voltage of 60 V serves larger ranges of motor envelope which possible to reach further than 50 V curve.

  6. The first of a new generation of diesel engines from General Motors - the efficient and powerful 1.6 liter Euro6 midsize diesel engine

    Energy Technology Data Exchange (ETDEWEB)

    Boretto, Gianmarco; Golisano, Roberto; Scotti, Michele; Antonioli, Pierpaolo; Frank, Richard M.; Rovatti, Giovanni [General Motors Powertrain Europe s.r.l., Turin (Italy); Wesslau, Markus [Adam Opel AG, Ruesselsheim (Germany)

    2013-08-01

    The major challenge the automotive industry will face in the next decade is undoubtedly the reduction of CO{sub 2} emissions. Conventional powertrains with internal combustion engines will still play a predominant role: in particular, the diesel engine will be a major contributor to the solution thanks to its intrinsic high thermodynamic efficiency and low-end torque which is a key enabler for downsizing engine displacement and downspeeding. In this context, General Motors has developed an entirely new 1.6 liter four-cylinder Midsize Diesel Engine (MDE), the first of a new generation of efficient and powerful diesel engines. Its development has been focused on the achievement of high power and torque density, superior fuel efficiency and state-of-the-art noise and vibration, while meeting the Euro6 emission standard in a wide range of B-, C- and D-segment vehicles, utilizing different exhaust aftertreatment solutions. The key technical features of the base engine, combustion system and emission reduction technologies, together with the innovative engine control unit, are described in this paper. (orig.)

  7. Implementation of exclusive truck facilities

    Energy Technology Data Exchange (ETDEWEB)

    Fekpe, E. [Battelle Memorial Inst., Columbus, OH (United States). Transportation Market Sector

    2007-07-01

    This paper discussed the issue of highway congestion, safety, and efficiency in freight movement on highways, with particular reference to the challenge of supporting increasing capacity demand from truck traffic. Innovative and practical solutions are needed to address the growing need for more efficient freight movement while maintaining acceptable levels of safety on highways. The concept of exclusive truck facilities (ETFs) is becoming an attractive option as a feasible strategy to help stabilize traffic flow, reduce congestion, improve safety, enhance transportation system management, improve access to freight facilities, and improve efficiency in freight movement along corridors of national importance. ETFs can either be truck only lanes or truckways. Passenger cars may not use ETFs. However, the use of ETFs could involve high costs of construction, maintenance, and acquisition of additional right of way. A cost-benefit analysis was performed for alternative ETF configurations under different traffic and site characteristics. A set of criteria was then proposed for identifying suitable locations for exclusive truck lanes. It was proposed that ETFs are economically feasible at locations with traffic volume of 100,000 vehicles per day or more and with a truck volume of at least 25 per cent of the traffic. In addition, the rate of truck-involved fatal crashes and level of service should be used to prioritize preliminary candidate locations that satisfy the traffic criteria. Consideration should also be given to the existence of freight terminals, ports, processing centers or regional distribution centres that are close to highways. 11 refs., 1 tab.

  8. Can cars and trucks coexist peacefully on highways? Analyzing the effectiveness of road safety policies in Europe.

    Science.gov (United States)

    Castillo-Manzano, José I; Castro-Nuño, Mercedes; Fageda, Xavier

    2015-04-01

    We examine the impact on the traffic accident rate of the interaction between trucks and cars on Europe's roads using a panel data set that covers the period 1999-2010. We find that rising motorization rates for trucks lead to higher traffic fatalities, while rising motorization rates for cars do not. Empirically, the model we build predicts the positive impact of stricter speed limit legislation for trucks in the reduction of road fatalities. These findings lend support to European strategies and aimed at promoting alternative modes of freight transport, including rail and maritime transport. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Cummins L10G in Kenworth truck 'viable today'

    International Nuclear Information System (INIS)

    Anon.

    1996-01-01

    As the culmination of five years of developmental work by Cummins Engines, BC Research Inc., and BC Gas Utility Ltd., a T800 Kenworth truck was outfitted with a new Cummins L10G natural gas engine, and two lightweight fully -wrapped Dynetek cylinders; it was pronounced to be 'a viable clean truck today'. The L10G spark-ignited engine operates at a relatively high peak efficiency of 37 per cent and is commercially available to meet the current California Air Resources Board heavy duty vehicle emission standards without the use of a catalytic converter. The L10G engine produces no particulate emissions, a very significant advantage, in view of the fact that particulate emissions have been identified as major contributors to respiratory ailments

  10. Engineering evaluation of the General Motors (GM) diesel rating and capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Gross, R.E.

    1992-04-01

    K-Reactor`s number one GM diesel (GM-lK) suffered recurrent, premature piston pin bushing failures between July 1990 and January 1991. These failures raised a concern that the engine`s original design capabilities were being exceeded. Were we asking old engines to do too much by powering 1200 kw (continuous) rated electrical generators? Was excessive wear of the piston pin bushings a result of having exceeded the engine`s capabilities (overload), or were the recent failures a direct result of poor quality, poor design, or defective replacement parts? Considering the engine`s overall performance for the past 30 years, during which an engine failure of this nature had never occurred, and the fact that 1200 kw was approximately 50% of the engine`s original tested capability, Reactor Engineering did not consider it likely that an overloaded engine caused bushing failures. What seemed more plausible was that the engine`s failure to perform was caused by deficiencies in, or poor quality of, replacement parts.The following report documents: (1) the results of K-Reactor EDG failure analysis; (2) correlation of P- and C-Reactor GM diesel teardowns; (3) the engine rebuild to blueprint specification; (4) how the engine was determined ready for test; (5) testing parameters that were developed; (6) a summary of test results and test insights; (7) how WSRC determined engine operation was acceptable; (8) independent review of 1200 kw operational data; (9) approval of the engines` 12OOkw continuous rating.

  11. French intensive truck garden

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, T D

    1983-01-01

    The French Intensive approach to truck gardening has the potential to provide substantially higher yields and lower per acre costs than do conventional farming techniques. It was the intent of this grant to show that there is the potential to accomplish the gains that the French Intensive method has to offer. It is obvious that locally grown food can greatly reduce transportation energy costs but when there is the consideration of higher efficiencies there will also be energy cost reductions due to lower fertilizer and pesticide useage. As with any farming technique, there is a substantial time interval for complete soil recovery after there have been made substantial soil modifications. There were major crop improvements even though there was such a short time since the soil had been greatly disturbed. It was also the intent of this grant to accomplish two other major objectives: first, the garden was managed under organic techniques which meant that there were no chemical fertilizers or synthetic pesticides to be used. Second, the garden was constructed so that a handicapped person in a wheelchair could manage and have a higher degree of self sufficiency with the garden. As an overall result, I would say that the garden has taken the first step of success and each year should become better.

  12. Safety climate and the distracted driving experiences of truck drivers.

    Science.gov (United States)

    Swedler, David I; Pollack, Keshia M; Agnew, Jacqueline

    2015-07-01

    For truck drivers, distracted driving is a workplace behavior that increases occupational injury risk. We propose safety climate as an appropriate lens through which researchers can examine occupational distracted driving. Using a mixed methods study design, we surveyed truck drivers using the Safety Climate Questionnaire (SCQ) complemented by semi-structured interviews of experts on distracted driving and truck safety. Safety climate was assessed by using the entire SCQ as an overall climate score, followed by factor analysis that identified the following safety climate factors: Communications and Procedures; Management Commitment; and Work Pressure. In multivariate regression, the overall safety climate scale was associated with having ever experienced a crash and/or distraction-involved swerving. Interview participants described how these SCQ constructs could affect occupational distracted driving. To reduce distraction-related crashes in their organizations, management can adhere to safe policies and procedures, invest in engineering controls, and develop safer communication procedures. © 2015 Wiley Periodicals, Inc.

  13. Results of the motor-operated valve engineering and testing program

    International Nuclear Information System (INIS)

    Black, B.R.

    1994-01-01

    The Texas Utilities Electric Company (TU Electric) motor-operated valve (MOV) program for implementing the recommendations of Generic Letter 89-10 has typically included the following: refurbishing each actuator, verifying each actuator's as-built configuration, testing each actuator's motor on a dynamometer, testing each actuator's torque spring pack (which is used to control the torque developed), testing each fully refurbished and reassembled actuator on a torque test stand, and testing as many MOVs as practicable both without fluid flow through the valve and with the maximum test conditions reasonably achievable (static and differential pressures (DP) conditions, respectively). Test data are acquired at 1,000 samples per second for stem thrust, stem torque, stem position, actuator compensator spring pack deflection, actuator torque spring pack deflection, motor current, motor voltage, motor three-phase power, valve upstream pressure, and valve downstream pressure, wherever practicable

  14. Modelling Truck Weigh Stations’ Locations based on Truck Traffic Flow and Overweight Violation: A Case Study in Bosnia and Herzegovina

    Directory of Open Access Journals (Sweden)

    Mirsad Kulović

    2018-04-01

    Full Text Available The number of registered commercial freight vehicles is constantly increasing, increasing therefore as well the traffic load on the roads in Bosnia and Herzegovina. A significant part of freight vehicles moving along the main and regional roads are overloaded and cause significant damage to road infrastructure, affect road safety and result in an increase of emissions of harmful gases for people and the environment. The overloading rate is extremely high, in particular with 5-axle trucks representing 58.7%. The research showed that the increased overload level ranges from 10-20% of the maximum permissible weight. The importance of load limits was recognized early in the history of road development. This interrelation led directly to limitations on vehicle loads, and laws were enacted in many countries to establish the maximum allowable motor vehicle sizes and weights. Strict enforcement of motor vehicle size and weight laws is a step toward reducing motor vehicle size and weight violations, heavy truck accidents, and, even more, improving road maintenance, rehabilitation expenditures and road safety. Thus, based on the applied model the objective of this paper is to evaluate and optimize the locations of truck weigh stations on the road network of Bosnia and Herzegovina.

  15. Optimum layout of engine thermal management; Optimale Auslegung des Motor-Thermomanagements

    Energy Technology Data Exchange (ETDEWEB)

    Beykirch, Ruediger; Knauf, Juergen; Lehmann, Joerg [FEV GmbH, Aachen (Germany). Simulation Ottomotoren; Beulshausen, Johannes [RWTH Aachen Univ. (Germany). Lehrstuhl fuer Verbrennungskraftmaschinen

    2013-05-01

    Optimising an engine's thermal management on the basis of different driving cycles and vehicle and engine tests is both time-consuming and costly. FEV GmbH, in cooperation with the Institute for Combustion Engines at RWTH Aachen University, has developed a holistic simulation model that enables the thermal management of an individual engine to be optimised.

  16. Transient and Steady-state Tests of the Space Power Research Engine with Resistive and Motor Loads

    Science.gov (United States)

    Rauch, Jeffrey S.; Kankam, M. David

    1995-01-01

    The NASA Lewis Research Center (LeRC) has been testing free-piston Stirling engine/linear alternators (FPSE/LA) to develop advanced power convertors for space-based electrical power generation. Tests reported herein were performed to evaluate the interaction and transient behavior of FPSE/LA-based power systems with typical user loads. Both resistive and small induction motor loads were tested with the space power research engine (SPRE) power system. Tests showed that the control system could maintain constant long term voltage and stable periodic operation over a large range of engine operating parameters and loads. Modest resistive load changes were shown to cause relatively large voltage and, therefore, piston and displacer amplitude excursions. Starting a typical small induction motor was shown to cause large and, in some cases, deleterious voltage transients. The tests identified the need for more effective controls, if FPSE/LAs are to be used for stand-alone power systems. The tests also generated a large body of transient dynamic data useful for analysis code validation.

  17. Transient and steady-state tests of the space power research engine with resistive and motor loads

    Science.gov (United States)

    Rauch, Jeffrey S.; Kankam, M. David

    1995-01-01

    The NASA Lewis Research Center (LeRC) has been testing free-piston Stirling engine/linear alternators (FPSE/LA) to develop advanced power convertors for space-based electrical power generation. Tests reported herein were performed to evaluate the interaction and transient behavior of FPSE/LA-based power systems with typical user loads. Both resistive and small induction motor loads were tested with the space power research engine (SPRE) power system. Tests showed that the control system could maintain constant long term voltage and stable periodic operation over a large range of engine operating parameters and loads. Modest resistive load changes were shown to cause relatively large voltage and, therefore, piston and displacer amplitude excursions. Starting a typical small induction motor was shown to cause large and, in some cases, deleterious voltage transients. The tests identified the need for more effective controls, if FPSE/LAs are to be used for stand-alone power systems. The tests also generated a large body of transient dynamic data useful for analysis code validation.

  18. Demonstration Project 111, ITS/CVO Technology Truck, Final Project Report

    Energy Technology Data Exchange (ETDEWEB)

    Gambrell, KP

    2002-01-11

    In 1995, the planning and building processes began to design and develop a mobile demonstration unit that could travel across the nation and be used as an effective outreach tool. In 1997, the unit was completed; and from June 1997 until December 2000, the Federal Highway Administration (FHWA)/Federal Motor Carrier Safety Administration (FMCSA) mobilized the Technology Truck, also known as Demonstration Project No. 111, ''Advanced Motor Carrier Operations and Safety Technologies.'' The project featured the latest available state-of-the-practice intelligent transportation systems (ITS) technologies designed to improve both the efficiency and safety of commercial vehicle operations (CVO). The Technology Truck was designed to inform and educate the motor carrier community and other stakeholders regarding ITS technologies, thus gaining support and buy-in for participation in the ITS program. The primary objective of the project was to demonstrate new and emerging ITS/CVO technologies and programs, showing their impact on motor carrier safety and productivity. In order to meet the objectives of the Technology Truck project, the FHWA/FMCSA formed public/private partnerships with industry and with Oak Ridge National Laboratory to demonstrate and display available ITS/CVO technologies in a cooperative effort. The mobile demonstration unit was showcased at national and regional conferences, symposiums, universities, truck shows and other venues, in an effort to reach as many potential users and decision makers as possible. By the end of the touring phase, the ITS/CVO Technology Truck had been demonstrated in 38 states, 4 Canadian provinces, 88 cities, and 114 events; been toured by 18,099 people; and traveled 115,233 miles. The market penetration for the Technology Truck exceeded 4,000,000, and the website received more than 25,000 hits. In addition to the Truck's visits, the portable ITS/CVO kiosk was demonstrated at 31 events in 23 cites in 15

  19. Engineering evaluation of the General Motors (GM) diesel rating and capabilities

    International Nuclear Information System (INIS)

    Gross, R.E.

    1992-04-01

    K-Reactor's number one GM diesel (GM-lK) suffered recurrent, premature piston pin bushing failures between July 1990 and January 1991. These failures raised a concern that the engine's original design capabilities were being exceeded. Were we asking old engines to do too much by powering 1200 kw (continuous) rated electrical generators? Was excessive wear of the piston pin bushings a result of having exceeded the engine's capabilities (overload), or were the recent failures a direct result of poor quality, poor design, or defective replacement parts? Considering the engine's overall performance for the past 30 years, during which an engine failure of this nature had never occurred, and the fact that 1200 kw was approximately 50% of the engine's original tested capability, Reactor Engineering did not consider it likely that an overloaded engine caused bushing failures. What seemed more plausible was that the engine's failure to perform was caused by deficiencies in, or poor quality of, replacement parts.The following report documents: (1) the results of K-Reactor EDG failure analysis; (2) correlation of P- and C-Reactor GM diesel teardowns; (3) the engine rebuild to blueprint specification; (4) how the engine was determined ready for test; (5) testing parameters that were developed; (6) a summary of test results and test insights; (7) how WSRC determined engine operation was acceptable; (8) independent review of 1200 kw operational data; (9) approval of the engines' 12OOkw continuous rating

  20. Experimental Measurement of the Flow Field of Heavy Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Fred Browand; Charles Radovich

    2005-05-31

    Flat flaps that enclose the trailer base on the sides and top are known to reduce truck drag and reduce fuel consumption. Such flapped-truck geometries have been studied in laboratory wind tunnels and in field tests. A recent review of wind tunnel data for a variety of truck geometries and flow Reynolds numbers show roughly similar values of peak drag reduction, but differ in the determination of the optimum flap angle. Optimum angles lie in the range 12 degrees-20 degrees, and may be sensitive to Reynolds number and truck geometry. The present field test is undertaken to provide additional estimates of the magnitude of the savings to be expected on a typical truck for five flap angles 10, 13, 16, 19, and 22 degrees. The flaps are constructed from a fiberglass-epoxy-matrix material and are one-quarter of the base width in length (about 61 cm, or 2 feet). They are attached along the rear door hinge lines on either side of the trailer, so that no gap appears at the joint between the flap and the side of the trailer The flap angle is adjusted by means of two aluminum supports. The present test is performed on the NASA Crows Landing Flight Facility at the northern end of the San Joaquin valley in California. The main runway is approximately 2400 meters in length, and is aligned approximately in a north-south direction The test procedure is to make a series of runs starting at either end of the runway. All runs are initiated under computer control to accelerate the truck to a target speed of 60 mph (96 6 km/hr), to proceed at the target speed for a fixed distance, and to decelerate at the far end of the runway. During a run, the broadcast fuel rate, the engine rpm, forward speed, elapsed time--as well as several other parameters (10 in all)--are digitized at a rate of 100 digitizations per second. Various flapped-conditions are interspersed with the ''no flaps'' control, and are sequenced in a different order on different days. Approximately 310 runs

  1. Large truck and bus crash facts, 2010.

    Science.gov (United States)

    2012-09-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2010. Selected crash statistics on passenger : vehicles are also presen...

  2. Large truck and bus crash facts, 2012.

    Science.gov (United States)

    2014-06-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2012. Selected crash statistics on passenger vehicles are also presented ...

  3. Large truck and bus crash facts, 2013.

    Science.gov (United States)

    2015-04-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2013. Selected crash statistics on passenger vehicles are also presented ...

  4. Large truck and bus crash facts, 2009.

    Science.gov (United States)

    2011-10-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2009. Selected crash statistics on passenger : vehicles are also presen...

  5. Large truck and bus crash facts, 2011.

    Science.gov (United States)

    2013-10-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2011. Selected crash statistics on passenger : vehicles are also presen...

  6. Naturalistic Study of Truck Following Behavior

    Science.gov (United States)

    2016-04-01

    Volpe conducted the Naturalistic study of truck following behavior to gain a better understanding of how trucks follow other vehicles in the real world, with the ultimate goal of supporting the Federal Highway Administration in the development of aut...

  7. Commercial truck parking and other safety issues.

    Science.gov (United States)

    2015-10-01

    Commercial truck parking is a safety issue, since trucks are involved in approximately 10% of all fatal accidents on interstates and : parkways in Kentucky. Drivers experience schedule demands and long hours on the road, yet they cannot easily determ...

  8. Papers on vehicle size : cars and trucks

    Science.gov (United States)

    1988-06-01

    The four papers in this volume describe analyses of car size : trends and truck occupant injuries and fatalities. All four were : written between June 1985 and December 1987. The topics : addressed include where heavy truck accidents occur, injury an...

  9. Trucks involved in fatal accidents factbook 2008.

    Science.gov (United States)

    2011-03-01

    This document presents aggregate statistics on trucks involved in traffic accidents in 2008. The : statistics are derived from the Trucks Involved in Fatal Accidents (TIFA) file, compiled by the : University of Michigan Transportation Research Instit...

  10. Trucks involved in fatal accidents factbook 2007.

    Science.gov (United States)

    2010-01-01

    This document presents aggregate statistics on trucks involved in traffic accidents in 2007. The : statistics are derived from the Trucks Involved in Fatal Accidents (TIFA) file, compiled by the : University of Michigan Transportation Research Instit...

  11. Aerodynamics Research Revolutionizes Truck Design

    Science.gov (United States)

    2008-01-01

    During the 1970s and 1980s, researchers at Dryden Flight Research Center conducted numerous tests to refine the shape of trucks to reduce aerodynamic drag and improved efficiency. During the 1980s and 1990s, a team based at Langley Research Center explored controlling drag and the flow of air around a moving body. Aeroserve Technologies Ltd., of Ottawa, Canada, with its subsidiary, Airtab LLC, in Loveland, Colorado, applied the research from Dryden and Langley to the development of the Airtab vortex generator. Airtabs create two counter-rotating vortices to reduce wind resistance and aerodynamic drag of trucks, trailers, recreational vehicles, and many other vehicles.

  12. Truck Roll Stability Data Collection and Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, SS

    2001-07-02

    The principal objective of this project was to collect and analyze vehicle and highway data that are relevant to the problem of truck rollover crashes, and in particular to the subset of rollover crashes that are caused by the driver error of entering a curve at a speed too great to allow safe completion of the turn. The data are of two sorts--vehicle dynamic performance data, and highway geometry data as revealed by vehicle behavior in normal driving. Vehicle dynamic performance data are relevant because the roll stability of a tractor trailer depends both on inherent physical characteristics of the vehicle and on the weight and distribution of the particular cargo that is being carried. Highway geometric data are relevant because the set of crashes of primary interest to this study are caused by lateral acceleration demand in a curve that exceeds the instantaneous roll stability of the vehicle. An analysis of data quality requires an evaluation of the equipment used to collect the data because the reliability and accuracy of both the equipment and the data could profoundly affect the safety of the driver and other highway users. Therefore, a concomitant objective was an evaluation of the performance of the set of data-collection equipment on the truck and trailer. The objective concerning evaluation of the equipment was accomplished, but the results were not entirely positive. Significant engineering apparently remains to be done before a reliable system can be fielded. Problems were identified with the trailer to tractor fiber optic connector used for this test. In an over-the-road environment, the communication between the trailer instrumentation and the tractor must be dependable. In addition, the computer in the truck must be able to withstand the rigors of the road. The major objective--data collection and analysis--was also accomplished. Using data collected by instruments on the truck, a ''bad-curve'' database can be generated. Using

  13. Heavy truck modeling for fuel consumption. Simulations and measurements

    Energy Technology Data Exchange (ETDEWEB)

    Sandberg, T.

    2001-12-01

    Fuel consumption for heavy trucks depends on many factors like roads, weather, and driver behavior that are hard for a manufacturer to influence. However, one design possibility is the power train configuration. Here a new simulation program for heavy trucks is created to find the configuration of the power train that gives the lowest fuel consumption for each transport task. For efficient simulations the model uses production code for speed and gear control, and it uses exchangeable data sets to allow simulation of the whole production range of engine types, on recorded road profiles from all over the world. Combined with a graphical user interface this application is called STARS (Scania Truck And Road Simulation). The forces of rolling resistance and air resistance in the model are validated through an experiment where the propeller shaft torque of a heavy truck is measured. It is found that the coefficient of rolling resistance is strongly dependent on tire temperature, not only on vehicle speed as expected. This led to the development of a new model for rolling resistance. The model includes the dynamic behavior of the tires and relates rolling resistance to tire temperature and vehicle speed. In another experiment the fuel consumption of a test truck in highway driving is measured. The altitude of the road is recorded with a barometer and used in the corresponding simulations. Despite of the limited accuracy of this equipment the simulation program manage to predict a level of fuel consumption only 2% lower than the real measurements. It is concluded that STARS is a good tool for predicting fuel consumption for trucks in highway driving and for comparing different power train configurations.

  14. Fuel Cell Hydroge Manifold for Lift Trucks

    DEFF Research Database (Denmark)

    Hosseinzadeh, Elham

    . Battery driven lift trucks are being used more and more in different companies to reduce their emissions. However, battery driven lift trucks need long time to recharge and may be out of work for a long time. Fuel cell driven lift trucks diminish this problem and are therefore getting more attention...

  15. Truck acceleration behavior study and acceleration lane length recommendations for metered on-ramps

    Directory of Open Access Journals (Sweden)

    Guangchuan Yang

    2016-10-01

    Full Text Available This paper investigated the actual truck acceleration capability at metered on-ramps. Truck acceleration performance data were collected through a video-based data collection method. A piecewise constant acceleration model was employed to capture truck acceleration characteristics. It was found that the existing acceleration length will affect truck drivers’ acceleration behavior. At the taper type ramp that has limited acceleration distance, acceleration profile indicated a decreasing trend with distance. While for the ramp with an auxiliary lane that has sufficient acceleration distance, it was found that the acceleration behavior is to have a high acceleration rate in the beginning, then acceleration rate decrease with speed increase, and high acceleration rate again as drivers approach the merging area. Field data show that the truck acceleration performance data documented in the ITE’s (Institute of Transportation Engineers “Traffic Engineering Handbook” are much lower than the field collected data. Also, based on the regression analysis of speed versus distance profiles, it was found that the AASHTO’s (American Association of State Highway and Transportation Officials Green Book acceleration length design guidance is insufficient to accommodate trucks at metered on-ramps. The required acceleration lengths for medium and heavy trucks are approximately 1.3 and 1.6 times of the Green Book design guideline, respectively.

  16. Engineering evaluation of the General Motors (GM) diesel rating and capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Gross, R.E.

    1992-04-01

    K-Reactor's number one GM diesel (GM-lK) suffered recurrent, premature piston pin bushing failures between July 1990 and January 1991. These failures raised a concern that the engine's original design capabilities were being exceeded. Were we asking old engines to do too much by powering 1200 kw (continuous) rated electrical generators Was excessive wear of the piston pin bushings a result of having exceeded the engine's capabilities (overload), or were the recent failures a direct result of poor quality, poor design, or defective replacement parts Considering the engine's overall performance for the past 30 years, during which an engine failure of this nature had never occurred, and the fact that 1200 kw was approximately 50% of the engine's original tested capability, Reactor Engineering did not consider it likely that an overloaded engine caused bushing failures. What seemed more plausible was that the engine's failure to perform was caused by deficiencies in, or poor quality of, replacement parts.The following report documents: (1) the results of K-Reactor EDG failure analysis; (2) correlation of P- and C-Reactor GM diesel teardowns; (3) the engine rebuild to blueprint specification; (4) how the engine was determined ready for test; (5) testing parameters that were developed; (6) a summary of test results and test insights; (7) how WSRC determined engine operation was acceptable; (8) independent review of 1200 kw operational data; (9) approval of the engines' 12OOkw continuous rating.

  17. Weather delay costs to trucking.

    Science.gov (United States)

    2012-11-01

    Estimates of the nations freight sector of transportation range to upwards of $600 billion of total gross domestic product with 70 percent of total value and 60 percent of total weight moving by truck. Weather-related delays can add significantly ...

  18. A tough truck for ATLAS

    CERN Multimedia

    2003-01-01

    One of the mobile support structures that will be used to manoeuvre and assemble components of the ATLAS detector in its cavern was put through its paces at the end of July and passed its load tests with flying colours. The tests, which involved the surveyors taking measurements to detect any load-induced mechanical deformations, were carried out in Building 191. "The "truck" has been subjected to static tests with loads of up to 1250 tonnes and can carry and transport on air cushions a nominal load of up to 1000 tonnes at a top speed of 30 cm per minute," explains project leader Tommi Nyman. "It took two weeks to assemble the truck's components, the last of which arrived at CERN on 24 June. It then took a further 20 days to load the truck up for the test." The 8.5 metre-high truck will be used for final assembly of some of the ATLAS components, including the calorimeters, in cavern UX15. This powerful device is the result of a collaboration between CERN and the Henryk Niewodniczanski Institute of Nuclear ...

  19. Pengaruh Prosentase Etanol terhadap Torsi dan Emisi Motor Indirect Injection dengan Memodifikasi Engine Control Module

    Directory of Open Access Journals (Sweden)

    Hadi Rahmad

    2016-10-01

    Full Text Available This research present the torque and exhaust emission level from four stroke indirect injection fuel system engine. An engine fueled by ethanol gasoline blend. The original Engine Controle Module injected lean mixture into Combustion Chamber. Lean Mixture decreased Torque drastically. Therefore, the Engine Controle Module was modified to produce stoichiometric mixture. Injector was controlled by digital pulse of Fuel Controller. Ethanol was added into gasoline 0% - 100% at 1500 rpm-5000 rpm. The result demonstrate that increasing ethanol concentration into gasoline fuel system, decreasing Torque, and CO, HC, CO2 emission. By increasing ethanol concentration also increase CO2 emission to 34.6%.

  20. Evaluación del funcionamiento de motores de combustión interna trabajando con biodiesel. // Evaluation of engine performance working with biodiesel.

    Directory of Open Access Journals (Sweden)

    R. Piloto Rodríguez

    2008-09-01

    Full Text Available En el presente trabajo se determinó la característica exterior de velocidad para dos motores de combustión internatrabajando con combustible biodiesel procedente de varias fuentes naturales y se comparó con la característica exterior develocidad de los motores originalmente trabajando con combustible diesel. Los motores fueron evaluados con variacionesde carga y velocidad. En uno de los motores ensayados fue determinada la presión en el interior de la cámara decombustión con el objetivo de evaluar el retardo de ignición. Fue observado que los motores trabajando con combustiblebiodiesel presentaban una disminución de la potencia efectiva y un aumento del consumo especifico de combustible. Seobservó una disminución del retardo de ignición cuando fue empleado el combustible biodiesel. También fue observadoque los gases contaminantes, excepto las emisiones de NOx y CO, disminuyen o permanecen constantes con el uso delbiocombustible.Palabras claves: Motores de combustión interna, biodiesel, emisiones, característica exterior de velocidad,retardo de ignición._____________________________________________________________________________Abstract:The engine outer velocity characterization for two engines was made working with biodiesel from different natural sources,and its performance was compared with the engine parameters using reference diesel. The engines were used varying loadand velocity. The ignition delay was obtained by measurement of in-cylinder pressure. A decrease in the effective powerand increase in the effective fuel consumption were observed in the engines when biodiesel is used. Biodiesel samplesshown shorter ignition delay than diesel. The pollutants emitted for the engine using biodiesel was lower than diesel, withthe exception of NOx and CO emissions.Key words: engine, biodiesel, emissions, outer velocity characteristic, ignition delay.

  1. 19 CFR 12.73 - Motor vehicle and engine compliance with Federal antipollution emission requirements.

    Science.gov (United States)

    2010-04-01

    ... requirements. This section is ancillary to the regulations of the U.S. Environmental Protection Agency (EPA.... Those regulations should be consulted for more detailed information concerning EPA emission requirements... and exclusions from emission requirements based on age of vehicle. The following motor vehicles...

  2. 49 CFR 176.905 - Motor vehicles or mechanical equipment powered by internal combustion engines.

    Science.gov (United States)

    2010-10-01

    ... of ignition. A motor vehicle or mechanical equipment showing any signs of leakage or electrical fault... equipment is stowed. (f) Each hold or compartment must be ventilated and fitted with an overhead water... smoke or fire detection system capable of alerting personnel on the bridge. (h) All electrical equipment...

  3. CETA truck and EVA restraint system

    Science.gov (United States)

    Beals, David C.; Merson, Wayne R.

    1991-01-01

    The Crew Equipment Translation Aid (CETA) experiment is an extravehicular activity (EVA) Space Transportation System (STS) based flight experiment which will explore various modes of transporting astronauts and light equipment for Space Station Freedom (SSF). The basic elements of CETA are: (1) two 25 foot long sections of monorail, which will be EVA assembled in the STS cargo bay to become a single 50 ft. rail called the track; (2) a wheeled baseplate called the truck which rolls along the track and can accept three cart concepts; and (3) the three carts which are designated manual, electric, and mechanical. The three carts serve as the astronaut restraint and locomotive interfaces with the track. The manual cart is powered by the astronaut grasping the track's handrail and pulling himself along. The electric cart is operated by an astronaut turning a generator which powers the electric motor and drives the cart. The mechanical cart is driven by a Bendix type transmission and is similar in concept to a man-propelled railroad cart. During launch and landing, the truck is attached to the deployable track by means of EVA removable restraint bolts and held in position by a system of retractable shims. These shims are positioned on the exterior of the rail for launch and landing and rotate out of the way for the duration of the experiment. The shims are held in position by strips of Velcro nap, which rub against the sides of the shim and exert a tailored force. The amount of force required to rotate the shims was a major EVA concern, along with operational repeatability and extreme temperature effects. The restraint system was tested in a thermal-vac and vibration environment and was shown to meet all of the initial design requirements. Using design inputs from the astronauts who will perform the EVA, CETA evolved through an iterative design process and represented a cooperative effort.

  4. Analysis of major trends in U.S. commercial trucking, 1977-2002.

    Energy Technology Data Exchange (ETDEWEB)

    Bertram, K. M.; Santini, D .J.; Vyas, A. D.

    2009-06-10

    This report focuses on various major long-range (1977-2002) and intermediate-range (1982-2002) U.S. commercial trucking trends. The primary sources of data for this period were the U.S. Bureau of the Census Vehicle Inventory and Use Survey and Truck Inventory and Use Survey. In addition, selected 1977-2002 data from the U.S. Department of Energy/Energy Information Administration and from the U.S. Department of Transportation/Federal Highway Administration's Highway Statistics were used. The report analyzes (1) overall gasoline and diesel fuel consumption patterns by passenger vehicles and trucks and (2) the population changes and fuels used by all commercial truck classes by selected truck type (single unit or combination), during specified time periods, with cargo-hauling commercial trucks given special emphasis. It also assesses trends in selected vehicle miles traveled, gallons per vehicle miles traveled, and gallons per cargo ton-mile traveled, as well as the effect of cargo tons per truck on fuel consumption. In addition, the report examines long-range trends for related factors (e.g., long-haul mileages driven by heavy trucks) and their impacts on reducing fuel consumption per cargo-ton-mile and the relative shares of total commercial fuel use among truck classes. It identifies the effects of these trends on U.S. petroleum consumption. The report also discusses basic engineering design and performance, national legislation on interstate highway construction, national demographic trends (e.g., suburbanization), and changes in U.S. corporate operations requirements, and it highlights their impacts on both the long-distance hauling and shorter-distance urban and suburban delivery markets of the commercial trucking industry.

  5. Small Engine Repair Modules (Workbook) = Reparacion de Motores Pequenos (Guia de Trabajo)

    Science.gov (United States)

    New York State Dept. of Correctional Services, Albany.

    This package contains an English-Language set of task procedure sheets dealing with small-engine repair and a Spanish translation of the same material. Addressed in the individual sections of the manual are the following aspects of engine tune-up, reconditioning, and troubleshooting: servicing air cleaners; cleaning gas tanks, fuel lines, and fuel…

  6. Impact of branched structures on cycloalkane ignition in a motored engine: Detailed product and conformational analyses

    KAUST Repository

    Kang, Dongil; Lilik, Gregory K.; Dillstrom, Vernon Tyler; Agudelo, John Ramiro; Lapuerta, Magí n; Al-Qurashi, Khalid; Boehman, André Louis

    2015-01-01

    , equivalence ratio of 0.5 and engine speed of 600. rpm. The engine compression ratio (CR) was gradually increased in a stepwise manner until autoignition occurred. It was found that ECH exhibited a significantly higher oxidation reactivity compared to its two

  7. Análisis de irreversibilidades en el comportamiento de un motor Stirling // Analysis of irreversibilities on performance of a Stirling engine

    Directory of Open Access Journals (Sweden)

    Juan José González-Bayón

    2011-05-01

    Full Text Available El objetivo de este estudio es determinar el efecto de las irreversibilidades (internas y externasdebidas a la transferencia de calor y las pérdidas de presión debidas a la fricción sobre elrendimiento de Segunda Ley de un motor Stirling de tipo considerando el volumen muerto. Elmotor Stirling es analizado usando un modelo matemático basado en las leyes de la termodinámicapara procesos con una velocidad finita. Se asume un modelo isotérmico de motor con volúmenes deespacio muerto en la zona caliente, zona fría y en el regenerador. Los resultados obtenidos muestranque a pesar de que teóricamente el motor Stirling posee un rendimiento igual al de Carnot, en lapráctica su rendimiento puede ser de 2 a 5 veces menor que éste, dependiendo de la eficiencia delregenerador, del volumen muerto, de la diferencia de temperatura entre fluido y focos térmicos y delas rpm a que se opere el motor.Palabras claves: motor Stirling, motor térmico regenerativo, análisis de irreversibilidades.____________________________________________________________________AbstractThe study aims to determine the effect of the internal and external irreversibilities caused by heattransfer and pressure losses due to friction on the Second Law performance of a Stirling engine tipewith death volume include. The Stirling engine is analyzed using a mathematical model based onthe laws of thermodynamics for processes with finite speed. It is assumed an isothermic model of themotor with death volume on hot zone, cold zone and regenerator. The results of this study show thatthe real cycle efficiency of the Sirling engine is approximately 2 to 5 times minor than the efficiency ofCarnot cycle as function of the regenerator efficiency, death volume, temperature difference betweenfluid and termic source and motor speed.Key words: stirling engine, regenerative heat engine, irreversibilities analysis.

  8. Parallel Multi-cycle LES of an Optical Pent-roof DISI Engine Under Motored Operating Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Van Dam, Noah; Sjöberg, Magnus; Zeng, Wei; Som, Sibendu

    2017-10-15

    The use of Large-eddy Simulations (LES) has increased due to their ability to resolve the turbulent fluctuations of engine flows and capture the resulting cycle-to-cycle variability. One drawback of LES, however, is the requirement to run multiple engine cycles to obtain the necessary cycle statistics for full validation. The standard method to obtain the cycles by running a single simulation through many engine cycles sequentially can take a long time to complete. Recently, a new strategy has been proposed by our research group to reduce the amount of time necessary to simulate the many engine cycles by running individual engine cycle simulations in parallel. With modern large computing systems this has the potential to reduce the amount of time necessary for a full set of simulated engine cycles to finish by up to an order of magnitude. In this paper, the Parallel Perturbation Methodology (PPM) is used to simulate up to 35 engine cycles of an optically accessible, pent-roof Directinjection Spark-ignition (DISI) engine at two different motored engine operating conditions, one throttled and one un-throttled. Comparisons are made against corresponding sequential-cycle simulations to verify the similarity of results using either methodology. Mean results from the PPM approach are very similar to sequential-cycle results with less than 0.5% difference in pressure and a magnitude structure index (MSI) of 0.95. Differences in cycle-to-cycle variability (CCV) predictions are larger, but close to the statistical uncertainty in the measurement for the number of cycles simulated. PPM LES results were also compared against experimental data. Mean quantities such as pressure or mean velocities were typically matched to within 5- 10%. Pressure CCVs were under-predicted, mostly due to the lack of any perturbations in the pressure boundary conditions between cycles. Velocity CCVs for the simulations had the same average magnitude as experiments, but the experimental data showed

  9. The ethanol heavy-duty truck fleet demonstration project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-06-01

    This project was designed to test and demonstrate the use of a high- percentage ethanol-blended fuel in a fleet of heavy-duty, over-the- road trucks, paying particular attention to emissions, performance, and repair and maintenance costs. This project also represents the first public demonstration of the use of ethanol fuels as a viable alternative to conventional diesel fuel in heavy-duty engines.

  10. Computations for Truck Sliding with TRUCK 3.1 Code

    Science.gov (United States)

    1989-08-01

    16 REFERENCES 1. L u. \\Villiam N.. Hobbs. Norman P. and Atkinson, Michael. TRUCK 3.1-An Improrcd Digital (’oiputtr Program for Calculating the Response...for Operations and Plans ATIN: Technical Libary Director of Chemical & Nuear Operations Dpartnt of the AIW Waskbington, DC 20310 1 Cocaeder US Ay...Lawrenoe Livermore Lab. ATIN: Code 2124, Tedhnical ATTN: Tech Info Dept L-3 Reports Libary P.O. Be 808 Monterey, CA 93940 Livermore, CA 94550 AFSC

  11. Powershift transmission for dump trucks; Neues Lastschaltgetriebe fuer Dump Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Rebholz, Wolfgang; Geis, Joerg; Riedhammer, Michael [ZF Friedrichshafen AG, Friedrichshafen (Germany)

    2012-04-15

    Articulated dumpers (also called dump trucks) are used in many locations where large quantities of earth, spoil, gravel or other materials have to be moved on construction sites or in quarries. ZF has developed a new transmission with eight forward and four reverse gears up to production standard specifically for use in these vehicles. The integrated primary retarder is continuously controllable and provides maximum braking torque of up to 1800 Nm. (orig.)

  12. Operation experiences of landfill gas engines; Motorer foer deponigas - Tillgaenglighet och drifterfarenheter

    Energy Technology Data Exchange (ETDEWEB)

    Dejfors, Charlotte; Grimberger, Goeran [AaF-Energikonsult Stockholm AB (Sweden)

    2000-06-01

    The gas that is obtained from landfilled waste is produced by bacteria that digest organic material in an anaerobic environment. Landfill gas consists mainly of methane, carbon dioxide and water vapour. It may be used either as auxiliary fuel in boilers close to the landfill or to generate electricity by means of a gas engine. Several plants where landfill gas is used in gas engines have had serious problems, a. o. with burned exhaust valves. These problems may occur already after a short period of operation, which influences the profitability. The purposes of the project reported were to collect operational experience in Sweden with engines using landfill gas as fuel, to identify which problems there are and which actions or improvements have been implemented in order to correct for these problems. Today, there are 9 facilities where landfill gas is used to fuel a total of 13 gas engines. In addition, there is an engine in Goeteborg which has scarcely been in operation after its installation because there is not enough gas. Contact has been taken with all these facilities. Many have pointed out that the gas engines are sensitive in the vicinity of maximum load, where the control system requires an even gas flow and a stable composition of the gas. A counter-measure in the facilities is to avoid running the engine at full load. All engines are equipped with a lean-NO{sub x} system in order to minimise NO{sub x} emissions. Many have remarked that the lean-NO{sub x} system shuts the engine off when emissions exceed the allowed limits. There is a consensus that spark plugs and ignition cables have created operational problems. These have been changed more frequently than originally expected. Another problem, which has caused operational problems and a need for maintenance, is deposits mainly in the combustion chamber, in valves and cylinder heads. Deposits and high exhaust gas temperature have led to burnt exhaust gas valves and cylinder heads on half of the engines

  13. Truck transportation of radioactive materials

    International Nuclear Information System (INIS)

    Madsen, M.M.; Wilmot, E.L.

    1983-01-01

    Analytical models in RADTRAN II are used to calculate risks to population subgroups such as people along transport routes, people at stops, and crewman. The stops model, which calculates the dose to persons adjacent to the transport vehicle while it is stopped, frequently provides the largest contribution to incident-free radiological impacts. Components such as distances from the vehicle containing radioactive material to nearby people at stops, stop duration, and number of crew members are required for the stops model as well as other incident-free models. To provide supporting data for RADTRAN II based on operational experience, selected truck shipments of radioactive material were observed from origin to destination. Other important aspects of this program were to correlate package size to effective shipment transport index (TI) using radiological surveys and to characterize population distributions and proximities of people to the shipment at a generic truck stop

  14. Motor SUS i životna sredina / IC engine and environment

    Directory of Open Access Journals (Sweden)

    Zoran Građin

    2002-03-01

    Full Text Available Ekološki pokreti u svetu su sve aktivniji, zbog stvarne ugroženosti Zemlje Mnogobrojni su oblici i izvori zagađenja, a jedan od najvećih su motori sa unutrašnjim sagorevanjem, za koje se pretpostavlja da će još dugo dominirati kao pogonski agregati u mnogim oblastima primene. U vezi s tim moguće je delovati u dva smera: zamenom konvencionalnih goriva alternativnim i konstrukcionim izmenama na motorima radi smanjenja emisije i potrošnje goriva. Jedna od mogućnosti konstrukcionog poboljšanja motora je i smanjenje mehaničkih gubitaka, koji kod današnjih konstrukcija još uvek imaju znatan udeo u gubicima, pogotovo na parcijalnim režimima. Treba naglasiti da kompleksni problemi smanjenja potrošnje goriva i emisije izduvnih gasova motora (vozila mogu da se reše samo spregom razvoja automobilske i naftne industrije. / Ecological trends and movements in the modern world grow stronger and more active, due to a real danger of Earth pollution. One of the main sources of pollution are IC engines and their influence on environment is significant. However, conventional combustion engines still are and will be dominant powering systems for numerous future applications. Two solutions are possible answers to this problem: first, the replacement of conventional fuels by alternative ones and second, modifications on the IC engine design in order to decrease fuel emission and consumption. One of the solutions for the improvement of IC engine design is the modification of engine parts or their design, with great influence on the decrease of mechanical losses, especially on partial rating. Therefore, it is important to say that complex problems of engine (automotive decrease of fuel consumption and exhaust gas emission can be solved only by simultaneous development of oil and engine (automotive industry.

  15. Sexual behavior among truck drivers.

    Science.gov (United States)

    Singh, Rajiv Kumar; Joshi, Hari Shankar

    2012-01-01

    A cross-sectional study was conducted on Lucknow highway in Bareilly district of Uttar Pradesh to study the knowledge of truck drivers about HIV transmission and prevention and to study the sexual behaviour of these drivers with reference to HIV/AIDS. Age, marital status, education, income, drinking alcohol, length of stay away from home, knowledge about transmission and prevention of HIV, and HIV-prone behavior of truck drivers were studied. Chi-square, mean, and SD were calculated. In all, 289 (97.6%) drivers had heard about HIV/AIDS. Only 242 (81.8%) were aware of HIV transmission by heterosexual route. Misconceptions such as HIV transmission by mosquito bites, living in same room, shaking hands, and sharing food were found. Out of 174 (58.8%) who visited Commercial Sex Workers (CSW), 146 (83.9%) used a condom. 38 (12.8%) visited more than 5 CSW in the last 3 months. Time away from home on the road, marital status, alcohol use, and income class were associated with visiting CSW. High-risk behavior was established in the study population. Safe sex and use of condoms need to be promoted among the truck drivers and better condom availability needs to be assured on highways.

  16. Carcinogenic potential of noxious emissions of diesel engines; Potencial cancerigeno de emisiones nocivas en motores a diesel

    Energy Technology Data Exchange (ETDEWEB)

    Romero Lopez, Alejandro F [Universidad Nacional Autonoma de Mexico, Mexico, D. F. (Mexico)

    1993-12-31

    The carcinogenic effects of the solid particles of carbonaceous nature, generated during the combustion process in the diesel engines, has been a concern of public and private entities in the developed countries, specially during the two last decades. This paper includes a short revision of the recent and preceding publications, found in the technical bibliography. The engine manufacturing enterprises have carried out spectacular changes in the internal design of the diesel engines, to diminish as much as possible, the solid particle generation inside the engine itself. The effort can not come from one part only, also the fuel producing enterprises in developed countries have carried out substantial efforts to improve the fuels as well as the lubricants. The goal of this measures is to practically eliminate the sulfur content, specially in the fuel, since the formation of solid particles linearly depends, among other factors, of this noxious element content in the diesel fuel. Finally, a short discussion is included of some exhaust gases post-treatment systems, that seems to be unavoidable in order to attain the strict standards that for year 1994 and the following years have been established by the Environmental Protection Agency (EPA) of the USA. The Mexican legislation is also analyzed through the Normas Tecnicas Ecologicas (NTE) (Ecological Technical Standards), emitted by the Secretaria de Desarrollo Urbano y Ecologia (SEDUE), now Secretaria de Desarrolo Economico y Social (SEDESOL), simply to have a comparison reference with the international legislation. [Espanol] Los efectos cancerigenos de las particulas solidas de caracter carbonaceo, generadas durante el proceso de combustion de los motores diesel, ha sido preocupacion de organismos publicos y privados en los paises desarrollados, en especial durante las ultimas dos decadas. El trabajo incluye una revision breve de publicaciones recientes y anteriores, que se encuentran en la literatura tecnica. Las

  17. Carcinogenic potential of noxious emissions of diesel engines; Potencial cancerigeno de emisiones nocivas en motores a diesel

    Energy Technology Data Exchange (ETDEWEB)

    Romero Lopez, Alejandro F. [Universidad Nacional Autonoma de Mexico, Mexico, D. F. (Mexico)

    1992-12-31

    The carcinogenic effects of the solid particles of carbonaceous nature, generated during the combustion process in the diesel engines, has been a concern of public and private entities in the developed countries, specially during the two last decades. This paper includes a short revision of the recent and preceding publications, found in the technical bibliography. The engine manufacturing enterprises have carried out spectacular changes in the internal design of the diesel engines, to diminish as much as possible, the solid particle generation inside the engine itself. The effort can not come from one part only, also the fuel producing enterprises in developed countries have carried out substantial efforts to improve the fuels as well as the lubricants. The goal of this measures is to practically eliminate the sulfur content, specially in the fuel, since the formation of solid particles linearly depends, among other factors, of this noxious element content in the diesel fuel. Finally, a short discussion is included of some exhaust gases post-treatment systems, that seems to be unavoidable in order to attain the strict standards that for year 1994 and the following years have been established by the Environmental Protection Agency (EPA) of the USA. The Mexican legislation is also analyzed through the Normas Tecnicas Ecologicas (NTE) (Ecological Technical Standards), emitted by the Secretaria de Desarrollo Urbano y Ecologia (SEDUE), now Secretaria de Desarrolo Economico y Social (SEDESOL), simply to have a comparison reference with the international legislation. [Espanol] Los efectos cancerigenos de las particulas solidas de caracter carbonaceo, generadas durante el proceso de combustion de los motores diesel, ha sido preocupacion de organismos publicos y privados en los paises desarrollados, en especial durante las ultimas dos decadas. El trabajo incluye una revision breve de publicaciones recientes y anteriores, que se encuentran en la literatura tecnica. Las

  18. Reverse Engineering Tone-Deafness: Disrupting Pitch-Matching by Creating Temporary Dysfunctions in the Auditory-Motor Network

    Directory of Open Access Journals (Sweden)

    Anja Hohmann

    2018-01-01

    Full Text Available Perceiving and producing vocal sounds are important functions of the auditory-motor system and are fundamental to communication. Prior studies have identified a network of brain regions involved in pitch production, specifically pitch matching. Here we reverse engineer the function of the auditory perception-production network by targeting specific cortical regions (e.g., right and left posterior superior temporal (pSTG and posterior inferior frontal gyri (pIFG with cathodal transcranial direct current stimulation (tDCS—commonly found to decrease excitability in the underlying cortical region—allowing us to causally test the role of particular nodes in this network. Performance on a pitch-matching task was determined before and after 20 min of cathodal stimulation. Acoustic analyses of pitch productions showed impaired accuracy after cathodal stimulation to the left pIFG and the right pSTG in comparison to sham stimulation. Both regions share particular roles in the feedback and feedforward motor control of pitched vocal production with a differential hemispheric dominance.

  19. Final Rule for Control of Air Pollution From Motor Vehicles and New Motor Vehicle Engines; Modification of Federal Onboard Diagnostic Regulations for Light-Duty Vehicles and Light-Duty Trucks; Extension of Acceptance of California OBD

    Science.gov (United States)

    This action finalizes modifications to the federal on-board diagnostics regulations, including: harmonizing the emission levels above which a component or system is considered malfunctioning with those of the California Air Resources Board (CARB).

  20. Large-Eddy Simulations of Motored Flow and Combustion in a Homogeneous-Charge Spark-Ignition Engine

    Science.gov (United States)

    Shekhawat, Yajuvendra Singh

    Cycle-to-cycle variations (CCV) of flow and combustion in internal combustion engines (ICE) limit their fuel efficiency and emissions potential. Large-eddy simulation (LES) is the most practical simulation tool to understand the nature of these CCV. In this research, multi-cycle LES of a two-valve, four-stroke, spark-ignition optical engine has been performed for motored and fired operations. The LES mesh quality is assessed using a length scale resolution parameter and a energy resolution parameter. For the motored operation, two 50-consecutive-cycle LES with different turbulence models (Smagorinsky model and dynamic structure model) are compared with the experiment. The pressure comparison shows that the LES is able to capture the wave-dynamics in the intake and exhaust ports. The LES velocity fields are compared with particle-image velocimetry (PIV) measurements at three cutting planes. Based on the structure and magnitude indices, the dynamic structure model is somewhat better than the Smagorinsky model as far as the ensemble-averaged velocity fields are concerned. The CCV in the velocity fields is assessed by proper-orthogonal decomposition (POD). The POD analysis shows that LES is able to capture the level of CCV seen in the experiment. For the fired operation, two 60-cycle LES with different combustion models (thickened frame model and coherent frame model) are compared with experiment. The in-cylinder pressure and the apparent heat release rate comparison shows higher CCV for LES compared to the experiment, with the thickened frame model showing higher CCV than the coherent frame model. The correlation analysis for the LES using thickened frame model shows that the CCV in combustion/pressure is correlated with: the tumble at the intake valve closing, the resolved and subfilter-scale kinetic energy just before spark time, and the second POD mode (shear flow near spark gap) of the velocity fields just before spark time.

  1. Upgrades for truck transportation of SNM in the Russian Federation

    International Nuclear Information System (INIS)

    Gardner, B.H.; Kornilovich, E.

    1998-01-01

    The goal of this project is the rapid reduction of risk to truck transportation of SNM in Russia. Enhanced protection is being accomplished by cooperation between the US Department of Energy, MINATOM of Russia, the Russian Ministry of Defense, and various Russian Institutes. This program provides an integrated program of specialized trucks that are equipped with hardened overpack (SNM vault) containers, alarm and communications systems, and armored cabs. Armored escort vehicles are also provided to increase the survivability of the guards escorting convoys. Only indigenous Russian equipment, modified and/or manufactured by Designing Bureau for Motor Vehicle Transport Equipment (KBATO), is provided under this program. The US will not provide assistance in the truck transportation arena without a commitment from the Russian facility to provide heavily armed escorts for SNM movement. Each site conducts a detailed transportation needs assessment study that is used as the basis for prioritizing assistance. The Siberian Chemical Combine (Tomsk-7) was the initial site of cooperation. The designs used at Tomsk-7 are serving as the baseline for all future vehicles modified under this program. In FY98, many vehicles systems have been ordered for various institutes. Many additional systems will be ordered in FY99

  2. Oxidation of Alkane Rich Gasoline Fuels and their Surrogates in a Motored Engine

    KAUST Repository

    Shankar, Vijai S B

    2015-03-30

    The validation of surrogates formulated using a computational framework by Ahmed et al.[1]for two purely paraffinic gasoline fuels labelled FACE A and FACE C was undertaken in this study. The ability of these surrogate mixtures to be used in modelling LTC engines was accessed by comparison of their low temperature oxidation chemistry with that of the respective parent fuel as well as a PRF based on RON. This was done by testing the surrogate mixtures in a modified Cooperative Fuels Research (CFR) engine running in Controlled Autoignition Mode (CAI) mode. The engine was run at a constant speed of 600 rpm at an equivalence ratio of 0.5 with the intake temperature at 150 °C and a pressure of 98 kPa. The low temperature reactivity of the fuels were studied by varying the compression ratio of the engine from the point were very only small low temperature heat release was observed to a point beyond which auto-ignition of the fuel/air mixture occurred. The apparent heat release rates of different fuels was calculated from the pressure histories using first law analysis and the CA 50 times of the low temperature heat release (LTHR) were compared. The surrogates reproduced the cool flame behavior of the parent fuels better than the PRF across all compression ratios.

  3. Oxidation of Alkane Rich Gasoline Fuels and their Surrogates in a Motored Engine

    KAUST Repository

    Shankar, Vijai S B; Al-Qurashi, Khalid; Ahmed, Ahfaz; Atef, Nour; Chung, Suk-Ho; Roberts, William L.; Sarathy, Mani

    2015-01-01

    The validation of surrogates formulated using a computational framework by Ahmed et al.[1]for two purely paraffinic gasoline fuels labelled FACE A and FACE C was undertaken in this study. The ability of these surrogate mixtures to be used in modelling LTC engines was accessed by comparison of their low temperature oxidation chemistry with that of the respective parent fuel as well as a PRF based on RON. This was done by testing the surrogate mixtures in a modified Cooperative Fuels Research (CFR) engine running in Controlled Autoignition Mode (CAI) mode. The engine was run at a constant speed of 600 rpm at an equivalence ratio of 0.5 with the intake temperature at 150 °C and a pressure of 98 kPa. The low temperature reactivity of the fuels were studied by varying the compression ratio of the engine from the point were very only small low temperature heat release was observed to a point beyond which auto-ignition of the fuel/air mixture occurred. The apparent heat release rates of different fuels was calculated from the pressure histories using first law analysis and the CA 50 times of the low temperature heat release (LTHR) were compared. The surrogates reproduced the cool flame behavior of the parent fuels better than the PRF across all compression ratios.

  4. STUDYING OF INFLUENCE OF BIOFUEL MOTOR QUALITIES ON POWER AND ECOLOGICAL CHARACTERISTICS OF THE DIESEL ENGINE

    Directory of Open Access Journals (Sweden)

    Levterov, A.

    2012-06-01

    Full Text Available The results of bench tests of D21A (2 Ч 10,5/12 diesel engine at its operation on mixed diesel fuel with improved qualities (Euro and the biofuel synthesized by the way of ethanol intereste-rification of rapeseed oil are offered.

  5. Determinants of fuel consumption in mining trucks

    International Nuclear Information System (INIS)

    Dindarloo, Saeid R.; Siami-Irdemoosa, Elnaz

    2016-01-01

    Analysis of fuel consumption in a large surface mine, during more than 5000 cycles of material transportation, revealed considerable variability in the data. Truck fuel estimation based on the mining truck manufacturers' manuals/estimates is not capable of capturing this variability in the fuel consumption data. Partial least squares regression and autoregressive integrated moving average methods were employed to examine the effect of cyclic activities on fuel consumption, and to recommend relevant remedies for consumption reduction. Proper modifications of the operation can result in improved cycle times. Consequently, minimizing some cyclic activities would enhance energy efficiency. The truck “empty idle time” was a major contributor to unnecessary fuel consumption. Since the truck queues at shovels are a major component of the “empty idle time”, decisions should be reviewed to reduce the truck queues at loading points. Improved dispatching strategies, optimal muck pile shape and size distribution, and improved shovel/loader operator skills are effective preventive measures to minimize truck flow bottlenecks at loading points, and thus to improve energy efficiency at mines. - Highlights: • A large fleet of mining trucks consumes considerable amounts of energy. • Current energy models do not consider the effect of site-specific mining conditions. • A new methodology based on material handling cyclic activities is proposed. • Fuel consumption rates in different truck operating modes are determined. • The new model is compared with the truck manufacturer's energy consumption guideline.

  6. Intrinsic movement variability at work. How long is the path from motor control to design engineering?

    Science.gov (United States)

    Gaudez, C; Gilles, M A; Savin, J

    2016-03-01

    For several years, increasing numbers of studies have highlighted the existence of movement variability. Before that, it was neglected in movement analysis and it is still almost completely ignored in workstation design. This article reviews motor control theories and factors influencing movement execution, and indicates how intrinsic movement variability is part of task completion. These background clarifications should help ergonomists and workstation designers to gain a better understanding of these concepts, which can then be used to improve design tools. We also question which techniques--kinematics, kinetics or muscular activity--and descriptors are most appropriate for describing intrinsic movement variability and for integration into design tools. By this way, simulations generated by designers for workstation design should be closer to the real movements performed by workers. This review emphasises the complexity of identifying, describing and processing intrinsic movement variability in occupational activities. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  7. Benefit of energy absorption by the truck in a frontal car-to-truck collision

    NARCIS (Netherlands)

    Coo, P.J.A. de; Adalian, C.

    2000-01-01

    EEVC Working Group 14 is investigating the effect of fixing energy absorbing front underrun protection systems (eaFUPS) to trucks instead of rigid devices in order to reduce the injury severity to car occupants in car-to-truck frontal collisions. Three car-to-truck crash tests with cars from

  8. 77 FR 488 - Control of Emissions From New Highway Vehicles and Engines; Approval of New Scheduled Maintenance...

    Science.gov (United States)

    2012-01-05

    ... (e.g., dump trucks, concrete mixers, refuse trucks, and other centrally-fueled vehicles) were... intervals for DEF-based SCR. For vocational vehicles such as dump trucks, concrete mixers, refuse trucks and... Engines; Approval of New Scheduled Maintenance for Selective Catalytic Reduction Technologies AGENCY...

  9. Space Launch System Base Heating Test: Sub-Scale Rocket Engine/Motor Design, Development and Performance Analysis

    Science.gov (United States)

    Mehta, Manish; Seaford, Mark; Kovarik, Brian; Dufrene, Aaron; Solly, Nathan; Kirchner, Robert; Engel, Carl D.

    2014-01-01

    The Space Launch System (SLS) base heating test is broken down into two test programs: (1) Pathfinder and (2) Main Test. The Pathfinder Test Program focuses on the design, development, hot-fire test and performance analyses of the 2% sub-scale SLS core-stage and booster element propulsion systems. The core-stage propulsion system is composed of four gaseous oxygen/hydrogen RS-25D model engines and the booster element is composed of two aluminum-based model solid rocket motors (SRMs). The first section of the paper discusses the motivation and test facility specifications for the test program. The second section briefly investigates the internal flow path of the design. The third section briefly shows the performance of the model RS-25D engines and SRMs for the conducted short duration hot-fire tests. Good agreement is observed based on design prediction analysis and test data. This program is a challenging research and development effort that has not been attempted in 40+ years for a NASA vehicle.

  10. Developing a GPS-based truck freight performance measure platform.

    Science.gov (United States)

    2010-05-01

    Although trucks move the largest volume and value of goods in urban areas, relatively little is known about their travel : patterns and how the roadway network performs for trucks. Global positioning systems (GPS) used by trucking : companies to mana...

  11. Combined impact of branching and unsaturation on the autoignition of binary blends in a motored engine

    KAUST Repository

    Kang, Dongil

    2014-11-20

    The impact of a branched and unsaturated compound (diisobutylene) mixed with simple hydrocarbons such as n-heptane and isooctane in binary blends on the autoignition behavior were investigated in a modified cooperative fuel research (CFR) engine at an equivlanece ratio of 0.5 and intake temperature of 120 °C. From this test condition, a homogeneous charge of fuel and intake air can be achieved. The test fuels were prepared by addition of 5-20 vol % diisobutylene into n-heptane and isooctane. The engine compression ratio (CR) was gradually increased from the lowest point to the point where significant high temperature heat release (HTHR) was observed, and this point is also referred to as the critical compression ratio (CCR). Heat release analysis showed that each n-heptane blend had a noticeable low temperature heat release (LTHR), which was not observed in the isooctane blends. The gradual addition of diisobutylene into each primary reference fuel contributed to retarded high temperature heat release in these binary blends, increasing the in-cylinder temperature and decreasing formation of CO. The 15 and 20 vol % blends of diisobutylene in isooctane were not able to reach high temperature heat release in the CFR engine system under these test conditions. The fundamental ignition behavior such as CCR and calculated % LTHR show the impact of the presence of the C-C double bond on ignition reactivity. Species concentration profiles obtained in condensed products from the engine exhaust were measured via gas chromatrography-mass spectrometry and -flame ionization detector. The major intermediate species for each blend were captured at a compression ratio selected just before the high temperature heat release was observed. Most intermediate species were derived from n-heptane and isooctane, while diisobutylene rarely participated in forming any major species, with the exception of the formation of 4,4-dimethyl-2-pentanone. Addition of diisobutylene exhibited opposite

  12. Combined impact of branching and unsaturation on the autoignition of binary blends in a motored engine

    KAUST Repository

    Kang, Dongil; Kirby, Stephen R.; Agudelo, John Ramiro; Lapuerta, Magí n; Al-Qurashi, Khalid; Boehman, André Louis

    2014-01-01

    The impact of a branched and unsaturated compound (diisobutylene) mixed with simple hydrocarbons such as n-heptane and isooctane in binary blends on the autoignition behavior were investigated in a modified cooperative fuel research (CFR) engine at an equivlanece ratio of 0.5 and intake temperature of 120 °C. From this test condition, a homogeneous charge of fuel and intake air can be achieved. The test fuels were prepared by addition of 5-20 vol % diisobutylene into n-heptane and isooctane. The engine compression ratio (CR) was gradually increased from the lowest point to the point where significant high temperature heat release (HTHR) was observed, and this point is also referred to as the critical compression ratio (CCR). Heat release analysis showed that each n-heptane blend had a noticeable low temperature heat release (LTHR), which was not observed in the isooctane blends. The gradual addition of diisobutylene into each primary reference fuel contributed to retarded high temperature heat release in these binary blends, increasing the in-cylinder temperature and decreasing formation of CO. The 15 and 20 vol % blends of diisobutylene in isooctane were not able to reach high temperature heat release in the CFR engine system under these test conditions. The fundamental ignition behavior such as CCR and calculated % LTHR show the impact of the presence of the C-C double bond on ignition reactivity. Species concentration profiles obtained in condensed products from the engine exhaust were measured via gas chromatrography-mass spectrometry and -flame ionization detector. The major intermediate species for each blend were captured at a compression ratio selected just before the high temperature heat release was observed. Most intermediate species were derived from n-heptane and isooctane, while diisobutylene rarely participated in forming any major species, with the exception of the formation of 4,4-dimethyl-2-pentanone. Addition of diisobutylene exhibited opposite

  13. A firm size and safety performance profile of the U.S. motor carrier industry : [executive summary].

    Science.gov (United States)

    2015-11-01

    Motor carrier crashes continue to present a societal and public policy : problem. Large commercial truck crashes are a topic of serious concern : in Iowa. Statistics illustrate the need to make further progress on the : safety performance of motor ca...

  14. Trucks involved in fatal accidents codebook 2008.

    Science.gov (United States)

    2011-01-01

    This report provides documentation for UMTRIs file of Trucks Involved in Fatal Accidents : (TIFA), 2008, including distributions of the code values for each variable in the file. The 2008 : TIFA file is a census of all medium and heavy trucks invo...

  15. Truck drivers as stakeholders in cooperative driving

    NARCIS (Netherlands)

    de Bruijn, F.; Terken, J.M.B.; Aarts, E.; de Ruyter, B.; Markopoulos, P.; van Loenen, E.; Wichert, R.; Schouten, B.; Terken, J.M.B.; van Kranenburg, R.; Den Ouden, E.; O'Hare, G.

    2014-01-01

    Cooperative driving for trucks has been claimed to bring substantial benefits for society and fleet owners because of better throughput and reduced fuel consumption, but benefits for truck drivers are questionable. While most work on cooperative driving focuses on the technology, the current paper

  16. Heavy truck rollover characterization (phase B).

    Science.gov (United States)

    2009-09-01

    The Heavy Truck Rollover Characterization Study - Phase-B builds on the results of prior phases of research. Phases 1 and 2 (Funded by Federal Highway Administration) involved heavy truck rollover characterization for a tractor and box-trailer; and P...

  17. Trusted Truck(R) II (phase A).

    Science.gov (United States)

    2009-01-01

    The Trusted Truck Program was initiated in 2003 as a joint effort by NTRCI, Volvo and UT. The vision of the Trusted Truck program is to develop a secure and "trusted" transport solution from pickup to delivery. The program's objective is to incre...

  18. 75 FR 76692 - Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety

    Science.gov (United States)

    2010-12-09

    ..., 510, 511, 512, 520, 523, 525, 526, and 571 [Docket No. NHTSA-2010-0159] Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety AGENCY: National Highway Traffic Safety... that specifically relate to passenger cars, multipurpose passenger vehicles, trucks, buses, trailers...

  19. Mistura de biodiesel de sebo bovino em motor diesel durante 600 horas Blend of biodiesel from beef tallow in a diesel engine during 600 hours of tests

    Directory of Open Access Journals (Sweden)

    Ila Maria Corrêa

    2011-07-01

    Full Text Available O biodiesel de sebo bovino é considerado uma alternativa de baixo custo e de grande disponibilidade por ser resíduo da produção agropecuária brasileira, que é uma das maiores do mundo. Raros são os trabalhos que mostram a utilização do biodiesel de sebo bovino em motores diesel. Assim, o objetivo deste trabalho foi verificar o efeito da mistura de biodiesel bovino na proporção de 5% ao óleo diesel comercial no desempenho do motor, possíveis consequências internas no motor e nas características do óleo lubrificante após o uso prolongado em motor diesel. Foram realizados ensaios em bancada dinamométrica utilizando um trator agrícola. O desempenho do motor foi determinado através da tomada de potência (TDP. O motor foi operado por 600h durante as quais foi determinada a potência, o consumo de combustível e analisadas as amostras de óleo lubrificante a cada 100h. Ao final do ensaio, o motor foi aberto e inspecionado. A análise do óleo lubrificante mostrou nível de contaminação crítico a partir das 400h, mas a inspeção visual do motor não detectou nenhum desgaste interno. O motor funcionou normalmente, embora tenha ocorrido tendência de redução na potência e aumento de consumo de combustível ao longo das 600h.Biodiesel from beef tallow has been considered a low-cost and high availability alternative due to be residue from the Brazilian livestock production, one of the world's largest. Papers that show the use of biodiesel from beef tallow in diesel engine are rare. The aim of this study was to investigate the effect of blend of biodiesel from beef tallow (B5 in commercial diesel oil on engine performance, analyzing possible internal consequences and characteristics of lubricating oil after the prolonged use in a diesel engine. Engine performance was evaluated through tractor power take off (PTO tests. The engine was operated for 600 hours. Power and fuel consumption were measured. Samples of lubricating oil were

  20. Fuel Cell Powered Lift Truck

    Energy Technology Data Exchange (ETDEWEB)

    Moulden, Steve [Sysco Food Service, Houston, TX (United States)

    2015-08-20

    This project, entitled “Recovery Act: Fuel Cell-Powered Lift Truck Sysco (Houston) Fleet Deployment”, was in response to DOE funding opportunity announcement DE-PS36-08GO98009, Topic 7B, which promotes the deployment of fuel cell powered material handling equipment in large, multi-shift distribution centers. This project promoted large-volume commercialdeployments and helped to create a market pull for material handling equipment (MHE) powered fuel cell systems. Specific outcomes and benefits involved the proliferation of fuel cell systems in 5-to 20-kW lift trucks at a high-profile, real-world site that demonstrated the benefits of fuel cell technology and served as a focal point for other nascent customers. The project allowed for the creation of expertise in providing service and support for MHE fuel cell powered systems, growth of existing product manufacturing expertise, and promoted existing fuel cell system and component companies. The project also stimulated other MHE fleet conversions helping to speed the adoption of fuel cell systems and hydrogen fueling technology. This document also contains the lessons learned during the project in order to communicate the successes and difficulties experienced, which could potentially assist others planning similar projects.

  1. Impact of branched structures on cycloalkane ignition in a motored engine: Detailed product and conformational analyses

    KAUST Repository

    Kang, Dongil

    2015-04-01

    The ignition process of ethylcyclohexane (ECH) and its two isomers, 1,3-dimethylcyclohexane (13DMCH) and 1,2-dimethylcyclohexane (12DMCH) was investigated in a modified CFR engine. The experiment was conducted with intake air temperature of 155. °C, equivalence ratio of 0.5 and engine speed of 600. rpm. The engine compression ratio (CR) was gradually increased in a stepwise manner until autoignition occurred. It was found that ECH exhibited a significantly higher oxidation reactivity compared to its two isomers. The autoignition criterion was based on CO emissions and the apparent heat release rates. Ethylcyclohexane (ECH) indicated noticeable two stage ignition behavior, while less significant heat release occurred for the two isomers at comparable conditions. The mole fractions of unreacted fuel and stable intermediate species over a wide range of compression ratios were analyzed by GC-MS and GC-FID. Most of the species indicated constant rates of formation and the trends of relative yield to unreacted fuel are well in agreement with the oxidation reactivity in the low temperature regime. The major intermediate species are revealed as a group of conjugate olefins, which possess the same molecular structure as the original fuel compound except for the presence of a double carbon bond. Conjugate olefins were mostly formed through (1,4) H-shift isomerization during the low temperature oxidation of alkylcyclohexanes. Conformation analysis explains the reactivity differences in the three isomers as well as the fractions of intermediate species. The hydrogen availability located in alkyl substituents plays an important role in determining oxidation reactivity, requiring less activation energy for abstraction through the (1,5) H-shift isomerization. This reactivity difference contributes to building up the major intermediate species observed during oxidation of each test fuel. 12DMCH, whose ignition reactivity is the lowest, less favors β-scission of C-C backbone of

  2. A battery-fuel cell hybrid auxiliary power unit for trucks: Analysis of direct and indirect hybrid configurations

    International Nuclear Information System (INIS)

    Samsun, Remzi Can; Krupp, Carsten; Baltzer, Sidney; Gnörich, Bruno; Peters, Ralf; Stolten, Detlef

    2016-01-01

    Highlights: • A battery-fuel cell hybrid auxiliary power unit for heavy duty vehicles is reported. • Comparison of direct and indirect hybrids using representative load profiles. • Evaluation based on validated fuel cell system and battery models. • Indirect hybrid with constant fuel cell load yields 29.3% hybrid system efficiency. • Fuel cell should be pre-heated using waste heat from the diesel engine during drive. - Abstract: The idling operation of engines in heavy duty vehicles to cover electricity demand during layovers entails significant fuel consumption and corresponding emissions. Indeed, this mode of operation is highly inefficient and a noteworthy contributor to the transportation sector’s aggregate carbon dioxide emissions. Here, a potential solution to this wasteful practice is outlined in the form of a hybrid battery-fuel cell system for application as an auxiliary power unit for trucks. Drawing on experimentally-validated fuel cell and battery models, several possible hybrid concepts are evaluated and direct and indirect hybrid configurations analyzed using a representative load profile. The results indicate that a direct hybrid configuration is only applicable if the load demand profile does not deviate strongly from the assumed profile. Operation of an indirect hybrid with a constant fuel cell load yields the greatest hybrid system efficiency, at 29.3%, while battery size could be reduced by 87% if the fuel cell is operated at the highest dynamics. Maximum efficiency in truck applications can be achieved by pre-heating the system prior to operation using exhaust heat from the motor, which increased system efficiency from 25.3% to 28.1%, including start-up. These findings confirm that hybrid systems could offer enormous fuel savings and constitute a sizeable step on the path toward energy-efficient and environmentally-friendly heavy duty vehicles that does not necessitate a fuel switch.

  3. Optimization of shovel-truck system for surface mining

    Energy Technology Data Exchange (ETDEWEB)

    Ercelebi, S.G.; Bascetin, A. [Istanbul Technical University, Istanbul (Turkey). Mining Engineering Department

    2009-07-15

    In surface mining operations, truck haulage is the largest item in the operating costs, constituting 50 to 60% of the total. In order to reduce this cost, it is necessary to allocate and dispatch the trucks efficiently. This paper describes shovel and truck operation models and optimization approaches for the allocation and dispatching of trucks under various operating conditions. Closed queuing network theory is employed for the allocation of trucks and linear programming for the purpose of truck dispatching to shovels. A case study was applied for the Orhaneli open Pit Coal Mine in Turkey. This approach would provide the capability of estimating system performance measures (mine throughput, mean number of trucks, mean waiting time, etc.) for planning purposes when the truck fleet is composed of identical trucks. A computational study is presented to show how choosing the optimum number of trucks and optimum dispatching policy affect the cost of moving material in a truck-shovel system.

  4. STRESS LOADING SIMULATION OF HYDRO-MECHANICAL TRANSMISSION OF DUMP TRUCK

    Directory of Open Access Journals (Sweden)

    S. A. Sidorov

    2006-01-01

    Full Text Available The Transmission model and software package to investigate stress loading of a hydromechanical transmission of a dump truck have been developed. The given software package allows to model stress loading of transmission gears in taking-off and acceleration modes at various road resistance, positions of an engine control pedal and initial revolutions of an engine crankshaft, various laws of friction clutch switching and some other parameters that permit to reveal a rate of various operational mode influence on stress loading of a dump truck transmission. An equivalence of the developed software is proved by the comparison of the experimentally obtained stress loading process of the hydro-mechanical transmission of a BelAZ- 7555 dump truck with the results of the simulation 

  5. Effects of After-Treatment Control Technologies on Heavy-Duty Diesel Truck Emissions

    Science.gov (United States)

    Preble, C.; Dallmann, T. R.; Kreisberg, N. M.; Hering, S. V.; Harley, R.; Kirchstetter, T.

    2015-12-01

    Diesel engines are major emitters of nitrogen oxides (NOx) and the black carbon (BC) fraction of particulate matter (PM). Diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems that target exhaust PM and NOx have recently become standard on new heavy-duty diesel trucks (HDDT). There is concern that DPFs may increase ultrafine particle (UFP) and total particle number (PN) emissions while reducing PM mass emissions. Also, the deliberate catalytic oxidation of engine-out NO to NO2 in continuously regenerating DPFs may lead to increased tailpipe emission of NO2 and near-roadway concentrations that exceed the 1-hr national ambient air quality standard. Increased NO2 emissions can also promote formation of ozone and secondary PM. We report results from ongoing on-road studies of HDDT emissions at the Port of Oakland and the Caldecott Tunnel in California's San Francisco Bay Area. Emission factors (g pollutant per kg diesel) were linked via recorded license plates to each truck's engine model year and installed emission controls. At both sites, DPF use significantly increased the NO2/NOx emission ratio. DPFs also significantly increased NO2 emissions when installed as retrofits on older trucks with higher baseline NOx emissions. While SCR systems on new trucks effectively reduce total NOx emissions and mitigate these undesirable DPF-related NO2 emissions, they also lead to significant emission of N2O, a potent greenhouse gas. When expressed on a CO2-equivalent basis, the N2O emissions increase offsets the fuel economy gain (i.e., the CO2 emission reduction) associated with SCR use. At the Port, average NOx, BC and PN emission factors from new trucks equipped with DPF and SCR were 69 ± 15%, 92 ± 32% and 66 ± 35% lower, respectively, than modern trucks without these emission controls. In contrast, at the Tunnel, PN emissions from older trucks retrofit with DPFs were ~2 times greater than modern trucks without DPFs. The difference

  6. Optimal Sizing and Control Strategy Design for Heavy Hybrid Electric Truck

    Directory of Open Access Journals (Sweden)

    Yuan Zou

    2012-01-01

    Full Text Available Due to the complexity of the hybrid powertrain, the control is highly involved to improve the collaborations of the different components. For the specific powertrain, the components' sizing just gives the possibility to propel the vehicle and the control will realize the function of the propulsion. Definitely the components' sizing also gives the constraints to the control design, which cause a close coupling between the sizing and control strategy design. This paper presents a parametric study focused on sizing of the powertrain components and optimization of the power split between the engine and electric motor for minimizing the fuel consumption. A framework is put forward to accomplish the optimal sizing and control design for a heavy parallel pre-AMT hybrid truck under the natural driving schedule. The iterative plant-controller combined optimization methodology is adopted to optimize the key parameters of the plant and control strategy simultaneously. A scalable powertrain model based on a bilevel optimization framework is built. Dynamic programming is applied to find the optimal control in the inner loop with a prescribed cycle. The parameters are optimized in the outer loop. The results are analysed and the optimal sizing and control strategy are achieved simultaneously.

  7. Hydrogen in motor car engineering. Production, storage, uses; Wasserstoff in der Fahrzeugtechnik. Erzeugung, Speicherung, Anwendung

    Energy Technology Data Exchange (ETDEWEB)

    Eichlseder, H.; Klell, M.

    2008-07-01

    The book presents a general outline of the various aspects of properties, production, storage and application of hydrogen at university level. The focus is on the thermodynamic aspects of hydrogen storage andon its applications in transportation and power supply. In particular, car engines and fuel cells are gone into, and the state of the art is outlined with reference to research projects of TU Graz university and HyCentA. Apart from the technical aspects, also the history and possible future trends are presented. [German] Dieses Buch bietet einen allgemeinen Ueberblick ueber die verschiedenen Aspekte von Eigenschaften, Erzeugung, Speicherung und Anwendung von Wasserstoff auf Hochschulniveau. Schwerpunkte liegen auf der Thermodynamik der Speicherung von Wasserstoff sowie auf der Anwendung in der Verkehrstechnik und in der Energietechnik. Speziell wird die Anwendung in der Verbrennungskraftmaschine und in der Brennstoffzelle behandelt, wobei mit Bezug auf Forschungsvorhaben an der TU Graz und dem HyCentA der aktuelle Stand der Technik fundiert dargestellt wird. Neben einer technischen Vertiefung werden auch die geschichtliche und die moegliche kuenftige Entwicklung angesprochen.

  8. A two-dimensional numerical study of the flow inside the combustion chamber of a motored rotary engine

    Science.gov (United States)

    Shih, T. I-P.; Yang, S. L.; Schock, H. J.

    1986-01-01

    A numerical study was performed to investigate the unsteady, multidimensional flow inside the combustion chambers of an idealized, two-dimensional, rotary engine under motored conditions. The numerical study was based on the time-dependent, two-dimensional, density-weighted, ensemble-averaged conservation equations of mass, species, momentum, and total energy valid for two-component ideal gas mixtures. The ensemble-averaged conservation equations were closed by a K-epsilon model of turbulence. This K-epsilon model of turbulence was modified to account for some of the effects of compressibility, streamline curvature, low-Reynolds number, and preferential stress dissipation. Numerical solutions to the conservation equations were obtained by the highly efficient implicit-factored method of Beam and Warming. The grid system needed to obtain solutions were generated by an algebraic grid generation technique based on transfinite interpolation. Results of the numerical study are presented in graphical form illustrating the flow patterns during intake, compression, gaseous fuel injection, expansion, and exhaust.

  9. A two-dimensional numerical study of the flow inside the combustion chambers of a motored rotary engine

    Science.gov (United States)

    Shih, T. I. P.; Yang, S. L.; Schock, H. J.

    1986-01-01

    A numerical study was performed to investigate the unsteady, multidimensional flow inside the combustion chambers of an idealized, two-dimensional, rotary engine under motored conditions. The numerical study was based on the time-dependent, two-dimensional, density-weighted, ensemble-averaged conservation equations of mass, species, momentum, and total energy valid for two-component ideal gas mixtures. The ensemble-averaged conservation equations were closed by a K-epsilon model of turbulence. This K-epsilon model of turbulence was modified to account for some of the effects of compressibility, streamline curvature, low-Reynolds number, and preferential stress dissipation. Numerical solutions to the conservation equations were obtained by the highly efficient implicit-factored method of Beam and Warming. The grid system needed to obtain solutions were generated by an algebraic grid generation technique based on transfinite interpolation. Results of the numerical study are presented in graphical form illustrating the flow patterns during intake, compression, gaseous fuel injection, expansion, and exhaust.

  10. Truck accident involving unirradiated nuclear fuel

    International Nuclear Information System (INIS)

    Carlson, R.W.; Fischer, L.E.

    1992-07-01

    In the early morning of Dec. 16, 1991, a severe accident occurred when a passenger vehicle traveling in the wrong direction collided with a tractor trailer carrying 24 nuclear fuel assemblies in 12 containers on Interstate 1-91 in Springfield, Massachusetts. This paper documents the mechanical circumstances of the accident and the physical environment to which the containers were exposed and the response of the containers and their contents. The accident involved four impacts where the truck was struck by the car, impacted on the center guardrail, impacted on the outer concrete barrier and came to rest against the center guardrail. The impacts were followed by a fire that began in the engine compartment, spread to the.tractor and cab, and eventually spread to the trailer and payload. The fire lasted for about three hours and the packages were involved in the fire for about two hours. As a result of the fire, the tractor-trailer was completely destroyed and the packages were exposed to flames with temperatures between 1300 degrees F and 1800 degrees F. The fuel assemblies remained intact during the accident and there was no release of any radioactive material during the accident. This was a very severe accident; however, the injuries were minor and at no time was the public health and safety at risk

  11. Truck accident involving unirradiated nuclear fuel

    International Nuclear Information System (INIS)

    Carlson, R.W.; Fischer, L.E.

    1993-01-01

    In the early morning of Dec. 16, 1991, a severe accident occurred when a passenger vehicle traveling in the wrong direction collided with a tractor trailer carrying 24 unirradiated nuclear fuel assemblies in 12 containers on Interstate I-91 in Springfield, Massachusetts. This paper documents the mechanical circumstances of the accident and assesses the physical environment to which the containers were exposed and the response of the containers and their contents. The accident involved four impacts where the truck was struck by the car, impacted on the center guardrail, impacted on the outer concrete barrier and came to rest against the center guardrail. The impacts were followed by a fire that began in the engine compartment, spread to the tractor and cab, and eventually spread to the trailer and payload. The fire lasted for about three hours and the packages were involved in the fire for about two hours. As a result of the fire, the tractor-trailer was completely destroyed and the packages were exposed to flames with temperatures between 1,300 F and 1,800 F. The fuel assemblies remained intact during the accident and there was no release of any radioactive material during the accident. This was a very severe accident; however, the injuries were minor and at no time was the public health and safety at risk

  12. Recovery Act--Class 8 Truck Freight Efficiency Improvement Project

    Energy Technology Data Exchange (ETDEWEB)

    Trucks, Daimler [Daimler Trucks North America Llc, Portland, OR (United States)

    2015-07-26

    Daimler Trucks North America completed a five year, $79.6M project to develop and demonstrate a concept vehicle with at least 50% freight efficiency improvement over a weighted average of several drive cycles relative to a 2009 best-in-class baseline vehicle. DTNA chose a very fuel efficient baseline vehicle, the 2009 Freightliner Cascadia with a DD15 engine, yet successfully demonstrated a 115% freight efficiency improvement. DTNA learned a great deal about the various technologies that were incorporated into Super Truck and those that, through down-selection, were discarded. Some of the technologies competed with each other for efficiency, and notably some of the technologies complemented each other. For example, we found that Super Truck’s improved aerodynamic drag resulted in improved fuel savings from eCoast, relative to a similar vehicle with worse aerodynamic drag. However, some technologies were in direct competition with each other, namely the predictive technologies which use GPS and 3D digital maps to efficiently manage the vehicles kinetic energy through controls and software, versus hybrid which is a much costlier technology that essentially targets the same inefficiency. Furthermore, the benefits of a comprehensive, integrated powertrain/vehicle approach was proven, in which vast improvements in vehicle efficiency (e.g. lower aero drag and driveline losses) enabled engine strategies such as downrating and downspeeding. The joint engine and vehicle developments proved to be a multiplier-effect which resulted in large freight efficiency improvements. Although a large number of technologies made the selection process and were used on the Super Truck demonstrator vehicle, some of the technologies proved not feasible for series production.

  13. n-Heptane cool flame chemistry: Unraveling intermediate species measured in a stirred reactor and motored engine

    KAUST Repository

    Wang, Zhandong

    2017-10-03

    This work identifies classes of cool flame intermediates from n-heptane low-temperature oxidation in a jet-stirred reactor (JSR) and a motored cooperative fuel research (CFR) engine. The sampled species from the JSR oxidation of a mixture of n-heptane/O2/Ar (0.01/0.11/0.88) were analyzed using a synchrotron vacuum ultraviolet radiation photoionization (SVUV-PI) time-of-flight molecular-beam mass spectrometer (MBMS) and an atmospheric pressure chemical ionization (APCI) Orbitrap mass spectrometer (OTMS). The OTMS was also used to analyze the sampled species from a CFR engine exhaust. Approximately 70 intermediates were detected by the SVUV-PI-MBMS, and their assigned molecular formulae are in good agreement with those detected by the APCI-OTMS, which has ultra-high mass resolving power and provides an accurate elemental C/H/O composition of the intermediate species. Furthermore, the results show that the species formed during the partial oxidation of n-heptane in the CFR engine are very similar to those produced in an ideal reactor, i.e., a JSR.The products can be classified by species with molecular formulae of C7H14Ox (x = 0–5), C7H12Ox (x = 0–4), C7H10Ox (x = 0–4), CnH2n (n = 2–6), CnH2n−2 (n = 4–6), CnH2n+2O (n = 1–4), CnH2nO (n = 1–6), CnH2n−2O (n = 2–6), CnH2n−4O (n = 4–6), CnH2n+2O2 (n = 0–4, 7), CnH2nO2 (n = 1–6), CnH2n−2O2 (n = 2–6), CnH2n−4O2 (n = 4–6), and CnH2nO3 (n = 3–6). The identified intermediate species include alkenes, dienes, aldehyde/keto compounds, olefinic aldehyde/keto compounds, diones, cyclic ethers, peroxides, acids, and alcohols/ethers. Reaction pathways forming these intermediates are proposed and discussed herein. These experimental results are important in the development of more accurate kinetic models for n-heptane and longer-chain alkanes.

  14. Toy Trucks in Video Analysis

    DEFF Research Database (Denmark)

    Buur, Jacob; Nakamura, Nanami; Larsen, Rainer Rye

    2015-01-01

    discovered that using scale-models like toy trucks has a strongly encouraging effect on developers/designers to collaboratively make sense of field videos. In our analysis of such scale-model sessions, we found some quite fundamental patterns of how participants utilise objects; the participants build shared......Video fieldstudies of people who could be potential users is widespread in design projects. How to analyse such video is, however, often challenging, as it is time consuming and requires a trained eye to unlock experiential knowledge in people’s practices. In our work with industrialists, we have...... narratives by moving the objects around, they name them to handle the complexity, they experience what happens in the video through their hands, and they use the video together with objects to create alternative narratives, and thus alternative solutions to the problems they observe. In this paper we claim...

  15. South Coast Air Quality Management District Truck Testing | Transportation

    Science.gov (United States)

    Research | NREL South Coast Air Quality Management District Truck Evaluation South Coast Air Quality Management District Truck Evaluation Photo of heavy-duty truck cab. Electric drayage truck Cargo Transportation project, conducted in partnership with the South Coast Air Quality Management

  16. 19 CFR 123.41 - Truck shipments transiting Canada.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Truck shipments transiting Canada. 123.41 Section... OF THE TREASURY CUSTOMS RELATIONS WITH CANADA AND MEXICO United States and Canada In-Transit Truck Procedures § 123.41 Truck shipments transiting Canada. (a) Manifest required. Trucks with merchandise...

  17. Desempenho de motor ciclo Diesel em bancada dinamométrica utilizando misturas diesel/biodiesel Performance of cycle Diesel engine in dynamometer using diesel/biodiesel mixtures

    Directory of Open Access Journals (Sweden)

    Marcio Castellanelli

    2008-03-01

    Full Text Available Diante da previsão de escassez do petróleo, o éster etílico (biodiesel tem-se apresentado como excelente opção de combustível alternativo para motores ciclo Diesel. As características do biodiesel são semelhantes às do diesel em termos de viscosidade e poder calorífico, podendo ser utilizado sem adaptações nos motores. Para a realização deste trabalho, utilizou-se de motor ciclo Diesel, de injeção direta, com quatro cilindros, sem adaptações. O motor foi acoplado a um dinamômetro e sistemas de aquisição de dados auxiliares. Avaliaram-se os desempenhos de torque, de potência e de consumo específico de combustível para as seguintes misturas diesel/éster etílico de soja: B2, B5, B10, B20, B50, B75 e B100. O melhor desempenho registrado deu-se com a mistura B20.Given the prediction of the scarcity of oil, the ethyl ester (biodiesel has presented as an excellent alternative fuel option for cycle diesel engine. The characteristics of biodiesel are similar of diesel in terms of viscosity and the calorific power, being able to be used without adaptations in the engines. For the accomplishment of this work it was used a cycle diesel engine, of direct injection with four cylinders, without adaptations. The engine was connected to a dynamometer and acquisition systems of auxiliary data. The performances of torque, power and specific fuel consumption for the following mixtures diesel/soy ethyl ester had been evaluated: B2, B5, B10, B20, B50, B75 and B100. The best registered performance was given with the B20 mixture.

  18. Hybrid component specification optimization for a medium-duty hybrid electric truck

    NARCIS (Netherlands)

    Hofman, T.; Steinbuch, M.; Druten, van R.M.; Serrarens, A.F.A.

    2008-01-01

    This paper presents a modelling and simulation approach for determining the optimal degree-of-hybridisation for the drive train (engine, electric machine size) and the energy storage system (battery, ultra capacitor) for a medium-duty truck. The results show that the degree-of-hybridisation of known

  19. Design/Operations review of core sampling trucks and associated equipment

    International Nuclear Information System (INIS)

    Shrivastava, H.P.

    1996-01-01

    A systematic review of the design and operations of the core sampling trucks was commissioned by Characterization Equipment Engineering of the Westinghouse Hanford Company in October 1995. The review team reviewed the design documents, specifications, operating procedure, training manuals and safety analysis reports. The review process, findings and corrective actions are summarized in this supporting document

  20. Hybrid vehicle motor alignment

    Science.gov (United States)

    Levin, Michael Benjamin

    2001-07-03

    A rotor of an electric motor for a motor vehicle is aligned to an axis of rotation for a crankshaft of an internal combustion engine having an internal combustion engine and an electric motor. A locator is provided on the crankshaft, a piloting tool is located radially by the first locator to the crankshaft. A stator of the electric motor is aligned to a second locator provided on the piloting tool. The stator is secured to the engine block. The rotor is aligned to the crankshaft and secured thereto.

  1. Effect of truck and rail economic deregulation on radioactive material transportation

    International Nuclear Information System (INIS)

    Allen, G.C. Jr.

    1984-01-01

    An evaluation of the effect of truck and rail economic deregulation on radioactive material transportation is presented in this document. The evaluation is based on expected market performance that would be consistent with fundamental economic theories. The issues of transport safety, commodity discrimination and rates are addressed. Relative to transport safety, deregulation should not have any significant impact. While deregulation should not change commodity acceptance and may lower rates for motor carriage, it may allow increased discrimination by rail carriers in addition to raising rates. Consequently, it is likely that the radioactive material transportation industry will continue to place greater reliance on the competitive motor carrier industry. Positive steps that shippers can take are to maintain credible options to ship by alternate modes, to address issues that result in the perceived need for special risk premiums, and to reduce the cost of handling truck shipments by improvements in technology or procedures. 28 references, 3 figures, 6 tables

  2. 49 CFR Appendix C to Part 541 - Criteria for Selecting Light Duty Truck Lines Likely To Have High Theft Rates

    Science.gov (United States)

    2010-10-01

    ... Likely To Have High Theft Rates C Appendix C to Part 541 Transportation Other Regulations Relating to... MOTOR VEHICLE THEFT PREVENTION STANDARD Pt. 541, App. C Appendix C to Part 541—Criteria for Selecting Light Duty Truck Lines Likely To Have High Theft Rates Scope These criteria specify the factors the...

  3. Acceptance test procedure for core sample trucks

    International Nuclear Information System (INIS)

    Smalley, J.L.

    1995-01-01

    The purpose of this Acceptance Test Procedure is to provide instruction and documentation for acceptance testing of the rotary mode core sample trucks, HO-68K-4600 and HO-68K-4647. The rotary mode core sample trucks were based upon the design of the second core sample truck (HO-68K-4345) which was constructed to implement rotary mode sampling of the waste tanks at Hanford. Acceptance testing of the rotary mode core sample trucks will verify that the design requirements have been met. All testing will be non-radioactive and stand-in materials shall be used to simulate waste tank conditions. Compressed air will be substituted for nitrogen during the majority of testing, with nitrogen being used only for flow characterization

  4. Truck side guard specifications : recommended standard

    Science.gov (United States)

    2016-09-01

    This document is intended to be used by (1) public or private medium/heavy-duty truck fleets considering adding side guards; (2) jurisdictions or customers that require side guards through policy or procurement; (3) manufacturers of side guards; and ...

  5. Slow speed object detection for haul trucks

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-09-15

    Caterpillar integrates radar technology with its current camera based system. Caterpillar has developed the Integrated Object Detection System, a slow speed object detection system for mining haul trucks. Object detection is a system that aids the truck operator's awareness of their surroundings. The system consists of a color touch screen display along with medium- and short-range radar as well as cameras, harnesses and mounting hardware. It is integrated into the truck's Work Area Vision System (WAVS). After field testing in 2007, system commercialization began in 2008. Prototype systems are in operation in Australia, Utah and Arizona and the Integrated Object Detection System will be available in the fourth quarter of 2009 and on production trucks 785C, 789C, 793D and 797B. The article is adapted from a presentation by Mark Richards of Caterpillar to the Haulage & Loading 2009 conference, May, held in Phoenix, AZ. 1 fig., 5 photos.

  6. Motor vehicle fuel economy, the forgotten HC control stragegy?

    Energy Technology Data Exchange (ETDEWEB)

    Deluchi, M.; Wang, Quanlu; Greene, D.L.

    1992-06-01

    Emissions of hydrocarbons from motor vehicles are recognized as major contributors to ozone pollution in urban areas. Petroleum-based motor fuels contain volatile organic compounds (VOC) which, together with oxides of nitrogen, promote the formation of ozone in the troposphere via complex photochemical reactions. VOC emissions from the tailpipe and evaporation from the fuel and engine systems of highway vehicles are believed to account for about 40% of total VOC emissions in any region. But motor fuels also generate emissions throughout the fuel cycle, from crude oil production to refining, storage, transportation, and handling, that can make significant contributions to the total inventory of VOC emissions. Many of these sources of emissions are directly related to the quantity of fuel produced and handled throughout the fuel cycle. It is, therefore, reasonable to expect that a reduction in total fuel throughput might result in a reduction of VOC emissions. In particular, reducing vehicle fuel consumption by increasing vehicle fuel economy should reduce total fuel throughput, thereby cutting total emissions of VOCS. In this report we identify the sources of VOC emissions throughout the motor fuel cycle, quantify them to the extent possible, and describe their dependence on automobile and light truck fuel economy.

  7. Crash problem definition and safety benefits methodology for stability control for single-unit medium and heavy trucks and large-platform buses

    Science.gov (United States)

    2009-10-01

    This report presents the findings of a comprehensive engineering analysis of electronic stability control (ESC) and roll stability control (RSC) systems for single-unit medium and heavy trucks and large-platform buses. This report details the applica...

  8. Particulate matters from diesel heavy duty trucks exhaust versus cigarettes emissions: a new educational antismoking instrument.

    Science.gov (United States)

    De Marco, Cinzia; Ruprecht, Ario Alberto; Pozzi, Paolo; Munarini, Elena; Ogliari, Anna Chiara; Mazza, Roberto; Boffi, Roberto

    2015-01-01

    Indoor smoking in public places and workplaces is forbidden in Italy since 2003, but some health concerns are arising from outdoor secondhand smoke (SHS) exposure for non-smokers. One of the biggest Italian Steel Manufacturer, with several factories in Italy and abroad, the Marcegaglia Group, recently introduced the outdoor smoking ban within the perimeter of all their factories. In order to encourage their smoker employees to quit, the Marcegaglia management decided to set up an educational framework by measuring the PM1, PM2.5 and PM10 emissions from heavy duty trucks and to compare them with the emissions of cigarettes in an indoor controlled environment under the same conditions. The exhaust pipe of two trucks powered by a diesel engine of about 13.000/14.000 cc(3) were connected with a flexible hose to a hole in the window of a container of 36 m(3) volume used as field office. The trucks operated idling for 8 min and then, after adequate office ventilation, a smoker smoked a cigarette. Particulate matter emission was thereafter analyzed. Cigarette pollution was much higher than the heavy duty truck one. Mean of the two tests was: PM1 truck 125.0(47.0), cigarettes 231.7(90.9) p = 0.002; PM2.5 truck 250.8(98.7), cigarettes 591.8(306.1) p = 0.006; PM10 truck 255.8(52.4), cigarettes 624.0(321.6) p = 0.002. Our findings may be important for policies that aim reducing outdoor SHS exposure. They may also help smokers to quit tobacco dependence by giving them an educational perspective that rebuts the common alibi that traffic pollution is more dangerous than cigarettes pollution.

  9. Improvement of the mining technology with the ring movement scheme of the haul trucks

    Directory of Open Access Journals (Sweden)

    Slobodyanyuk R.V.

    2016-04-01

    Full Text Available The article describes the designed technology that allows to expand the use of the haul truck ring movement scheme and to reduce the share of an empty run time in the transportation cycle. A preliminary calculation of the efficiency of its usage has allowed to confirm the main advantages of this scheme over the existing one as follows: reducing the required number of transport for the needs of open-pit mine operation by increasing the productivity of mining trucks; decreasing the transport operating costs (some part of an empty truck movement occurs when the engine is switched off; dropping the probability of accidents (reduced a number of the counter transport maneuvers. The calculation showed the regularity of changes in the efficiency using the alternative scheme in relation to the basic one, which reflecting significantly higher effectiveness in situations with a smaller distance between the empty run sites of the ring scheme.

  10. The impacts of multiple rest-break periods on commercial truck driver's crash risk.

    Science.gov (United States)

    Chen, Chen; Xie, Yuanchang

    2014-02-01

    Driver fatigue has been a major contributing factor to fatal commercial truck crashes, which accounted for about 10% of all fatal motor vehicle crashes that happened between 2009 and 2011. Commercial truck drivers' safety performance can deteriorate easily due to fatigue caused by long driving hours and irregular working schedules. To ensure safety, truck drivers often use off-duty time and short rest breaks during a trip to recover from fatigue. This study thoroughly investigates the impacts of off-duty time prior to a trip and short rest breaks on commercial truck safety by using Cox proportional hazards model and Andersen-Gill model. It is found that increasing total rest-break duration can consistently reduce fatigue-related crash risk. Similarly, taking more rest breaks can help to reduce crash risk. The results suggest that two rest breaks are generally considered enough for a 10-hour trip, as three or more rest breaks may not further reduce crash risk substantially. Also, the length of each rest break does not need to be very long and 30min is usually adequate. In addition, this study investigates the safety impacts of when to take rest breaks. It is found that taking rest breaks too soon after a trip starts will cause the rest breaks to be less effective. The findings of this research can help policy makers and trucking companies better understand the impacts of multiple rest-break periods and develop more effective rules to improve the safety of truck drivers. Copyright © 2014 Elsevier Ltd and National Safety Council. All rights reserved.

  11. Commercial truck crash injury severity analysis using gradient boosting data mining model.

    Science.gov (United States)

    Zheng, Zijian; Lu, Pan; Lantz, Brenda

    2018-06-01

    Truck crashes contribute to a large number of injuries and fatalities. This study seeks to identify the contributing factors affecting truck crash severity using 2010 to 2016 North Dakota and Colorado crash data provided by the Federal Motor Carrier Safety Administration. To fulfill a gap of previous studies, broad considerations of company and driver characteristics, such as company size and driver's license class, along with vehicle types and crash characteristics are researched. Gradient boosting, a data mining technique, is applied to comprehensively analyze the relationship between crash severities and a set of heterogeneous risk factors. Twenty five variables were tested and 22 of them are identified as significant variables contributing to injury severities, however, top 11 variables account for more than 80% of injury forecasting. The relative variable importance analysis is conducted and furthermore marginal effects of all contributing factors are also illustrated in this research. Several factors such as trucking company attributes (e.g., company size), safety inspection values, trucking company commerce status (e.g., interstate or intrastate), time of day, driver's age, first harmful events, and registration condition are found to be significantly associated with crash injury severity. Even though most of the identified contributing factors are significant for all four levels of crash severity, their relative importance and marginal effect are all different. For the first time, trucking company and driver characteristics are proved to have significant impact on truck crash injury severity. Some of the results in this study reinforce previous studies' conclusions. Findings in this study can be helpful for transportation agencies to reduce injury severity, and develop efficient strategies to improve safety. Copyright © 2018 National Safety Council and Elsevier Ltd. All rights reserved.

  12. Analysis of Technology Options to Reduce the Fuel Consumption of Idling Trucks; FINAL

    International Nuclear Information System (INIS)

    Stodolsky, F.; Gaines, L.; Vyas, A.

    2000-01-01

    Long-haul trucks idling overnight consume more than 838 million gallons (20 million barrels) of fuel annually. Idling also emits pollutants. Truck drivers idle their engines primarily to (1) heat or cool the cab and/or sleeper, (2) keep the fuel warm in winter, and (3) keep the engine warm in the winter so that the engine is easier to start. Alternatives to overnight idling could save much of this fuel, reduce emissions, and cut operating costs. Several fuel-efficient alternatives to idling are available to provide heating and cooling: (1) direct-fired heater for cab/sleeper heating, with or without storage cooling; (2) auxiliary power units; and (3) truck stop electrification. Many of these technologies have drawbacks that limit market acceptance. Options that supply electricity are economically viable for trucks that are idled for 1,000-3,000 or more hours a year, while heater units could be used across the board. Payback times for fleets, which would receive quantity discounts on the prices, would be somewhat shorter

  13. Structure of energy consumption and improving open-pit dump truck efficiency

    Science.gov (United States)

    Koptev, V. Yu; Kopteva, A. V.

    2017-10-01

    This paper studies the dynamics of the improvement of wheel type transport vehicles environmental and energy performance in open-pit mines. The paper discloses characteristics of the gas turbine engine with capacity of 1250 hp, mounted on tanks, and technical-economic calculations, confirming reasonability of their use in open-pit dump trucks with the 120 …130-ton loading capacity. The general layout scheme of mechanical transmission with the gas turbine engine is shown.

  14. STRESS LOADING SIMULATION OF HYDRO-MECHANICAL TRANSMISSION OF DUMP TRUCK

    OpenAIRE

    S. A. Sidorov

    2006-01-01

    The Transmission model and software package to investigate stress loading of a hydromechanical transmission of a dump truck have been developed. The given software package allows to model stress loading of transmission gears in taking-off and acceleration modes at various road resistance, positions of an engine control pedal and initial revolutions of an engine crankshaft, various laws of friction clutch switching and some other parameters that permit to reveal a rate of various operational m...

  15. Application of Sleeper Cab Thermal Management Technologies to Reduce Idle Climate Control Loads in Long-Haul Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Lustbader, J. A.; Venson, T.; Adelman, S.; Dehart, C.; Yeakel, S.; Castillo, M. S.

    2012-10-01

    Each intercity long-haul truck in the U.S. idles approximately 1,800 hrs per year, primarily for sleeper cab hotel loads. Including workday idling, over 2 billion gallons of fuel are used annually for truck idling. NREL's CoolCab project works closely with industry to design efficient thermal management systems for long-haul trucks that keep the cab comfortable with minimized engine idling and fuel use. The impact of thermal load reduction technologies on idle reduction systems were characterized by conducting thermal soak tests, overall heat transfer tests, and 10-hour rest period A/C tests. Technologies evaluated include advanced insulation packages, a solar reflective film applied to the vehicle's opaque exterior surfaces, a truck featuring both film and insulation, and a battery-powered A/C system. Opportunities were identified to reduce heating and cooling loads for long-haul truck idling by 36% and 34%, respectively, which yielded a 23% reduction in battery pack capacity of the idle-reduction system. Data were also collected for development and validation of a CoolCalc HVAC truck cab model. CoolCalc is an easy-to-use, simplified, physics-based HVAC load estimation tool that requires no meshing, has flexible geometry, excludes unnecessary detail, and is less time-intensive than more detailed computer-aided engineering modeling approaches.

  16. Gas fuelled heavy-duty trucks for municipal services

    Energy Technology Data Exchange (ETDEWEB)

    Forsberg, A. (City of Helsinki Construction Services (Finland)); Hietanen, L. (Lassila and Tikanoja, Jyvaeskylae (Finland)); Nylund, N.-O. (TEC TransEnergy Consulting, Espoo (Finland))

    2009-07-01

    Helsinki City Public Works Department (HKR) and the environmental management company Lassila and Tikanoja joined forces to demonstrate the suitability of heavy-duty gas fuelled trucks for municipal services. HKR acquired two and Lassila and Tikanoja five Mercedes-Benz Econic trucks. HKR's trucks are equipped with interchangeable platforms, Lassila an Tikanoja's trucks with refuse collection equipment. The trucks are subjected to a two-year follow-up study to establish reliability, operational costs and exhaust emissions. Diesel trucks representing up-to-date technology are used as reference. If the gas fuelled trucks perform well, this can lead to increased numbers of natural gas trucks in municipal services, and in the long run to the introduction of biogas fuelled trucks. (orig.)

  17. Micro generation of electricity with gasification gas in a engine generator in dual mode; Microgeracao de eletricidade com gas de gaseificacao num motor gerador dual

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Marcelo Jose da; Souza, Samuel Nelson Melegari de; Souza, Abel Alves de; Ricieri, Reinaldo P. [Universidade Estadual do Oeste do Parana (UNIOESTE), Cascavel, PE (Brazil)], E-mail: marcelo_js07@hotmail.com

    2010-07-01

    Among the alternatives to the increase of world energy demand the use of biomass as energy source is one of the most promising as it contributes to reducing emissions of carbon dioxide in the atmosphere. Gasification is a process technology of biomass energy in a gaseous biofuel. The fuel gas got a low calorific value that can be used in diesel engine in dual mode for power generation in isolated communities. This study aimed to evaluate the reduction in the consumption of oil diesel an engine generator, using gas from gasification of wood. The engine generator brand used, it was a BRANCO, with direct injection power of 10 hp and mated to an electric generator 5,5 kW. The fuel gas was produced in a gasifier type co-current. The engine generator was put on load system from 0.5 kW to 3.5 kW through electric bank of heaters. For the oil diesel savings, the gas was injected mixed with intake air, as the oil diesel was normally injected by the injector of the engine (motor dual). The consumption od diesel was measured diesel by means of a precision scale. It was concluded that the engine converted to dual mode when using the gas for the gasification of wood showed a decrease in diesel consumption by up to 57%. (author)

  18. Effects of Particle Filters and Selective Catalytic Reduction on In-Use Heavy-Duty Diesel Truck Emissions

    Science.gov (United States)

    Preble, C.; Cados, T.; Harley, R.; Kirchstetter, T.

    2016-12-01

    Heavy-duty diesel trucks (HDDT) are a major source of nitrogen oxides (NOx) and black carbon (BC) in urban environments, contributing to persistent ozone and particulate matter air quality problems. Diesel particle filters (DPFs) and selective catalytic reduction (SCR) systems that target PM and NOx emissions, respectively, have recently become standard equipment on new HDDT. DPFs can also be installed on older engines as a retrofit device. Previous work has shown that DPF and SCR systems can reduce NOx and BC emissions by up to 70% and 90%, respectively, compared to modern trucks without these after-treatment controls (Preble et al., ES&T 2015). DPFs can have the undesirable side-effect of increasing ultrafine particle (UFP) and nitrogen dioxide (NO2) emissions. While SCR systems can partially mitigate DPF-related NO2 increases, these systems can emit nitrous oxide (N2O), a potent greenhouse gas. We report new results from a study of HDDT emissions conducted in fall 2015 at the Port of Oakland and Caldecott Tunnel in California's San Francisco Bay Area. We report pollutant emission factors (g kg-1) for emitted NOx, NO2, BC, PM2.5, UFP, and N2O on a truck-by-truck basis. Using a roadside license plate recognition system, we categorize each truck by its engine model year and installed after-treatment controls. From this, we develop emissions profiles for trucks with and without DPF and SCR. We evaluate the effectiveness of these devices as a function of their age to determine whether degradation is an issue. We also compare the emission profiles of trucks traveling at low speeds along a level, arterial road en route to the port and at high speeds up a 4% grade highway approaching the tunnel. Given the climate impacts of BC and N2O, we also examine the global warming potential of emissions from trucks with and without DPF and SCR.

  19. Business plan for Gourmet Food Truck in Helsinki

    OpenAIRE

    Mulmi, Mukesh

    2015-01-01

    This thesis work is about food truck and food truck industry in Finland. In Finland, Culinary scenes are booming and growing but, the food truck concept is new to Finland. Food truck industry is very young and currently, there is a hype for food truck and people are admiring new cuisines. Author himself is working as a cook. And he is passionate about food and restaurant industry. The main purpose of the thesis was to explore more about food truck industry in Finland and create the busine...

  20. Driver Injury Risk Variability in Finite Element Reconstructions of Crash Injury Research and Engineering Network (CIREN) Frontal Motor Vehicle Crashes.

    Science.gov (United States)

    Gaewsky, James P; Weaver, Ashley A; Koya, Bharath; Stitzel, Joel D

    2015-01-01

    A 3-phase real-world motor vehicle crash (MVC) reconstruction method was developed to analyze injury variability as a function of precrash occupant position for 2 full-frontal Crash Injury Research and Engineering Network (CIREN) cases. Phase I: A finite element (FE) simplified vehicle model (SVM) was developed and tuned to mimic the frontal crash characteristics of the CIREN case vehicle (Camry or Cobalt) using frontal New Car Assessment Program (NCAP) crash test data. Phase II: The Toyota HUman Model for Safety (THUMS) v4.01 was positioned in 120 precrash configurations per case within the SVM. Five occupant positioning variables were varied using a Latin hypercube design of experiments: seat track position, seat back angle, D-ring height, steering column angle, and steering column telescoping position. An additional baseline simulation was performed that aimed to match the precrash occupant position documented in CIREN for each case. Phase III: FE simulations were then performed using kinematic boundary conditions from each vehicle's event data recorder (EDR). HIC15, combined thoracic index (CTI), femur forces, and strain-based injury metrics in the lung and lumbar vertebrae were evaluated to predict injury. Tuning the SVM to specific vehicle models resulted in close matches between simulated and test injury metric data, allowing the tuned SVM to be used in each case reconstruction with EDR-derived boundary conditions. Simulations with the most rearward seats and reclined seat backs had the greatest HIC15, head injury risk, CTI, and chest injury risk. Calculated injury risks for the head, chest, and femur closely correlated to the CIREN occupant injury patterns. CTI in the Camry case yielded a 54% probability of Abbreviated Injury Scale (AIS) 2+ chest injury in the baseline case simulation and ranged from 34 to 88% (mean = 61%) risk in the least and most dangerous occupant positions. The greater than 50% probability was consistent with the case occupant's AIS 2

  1. 76 FR 54932 - Revisions and Additions to Motor Vehicle Fuel Economy Label; Correction

    Science.gov (United States)

    2011-09-06

    ...-AK73 Revisions and Additions to Motor Vehicle Fuel Economy Label; Correction AGENCY: Environmental... regarding labeling of cars and trucks with fuel economy and environmental information in the Federal...

  2. Impact of left lane truck restriction strategies on multilane highways in Louisiana : a literature review.

    Science.gov (United States)

    2009-04-01

    Truck lane restriction strategies (TLRS) are a means of managing truck traffic on highways by prohibiting trucks from using certain lanes to minimize interaction between trucks and other vehicles. The purpose of this study is to review the literature...

  3. The open-pit truck dispatching method based on the completion of production target and the truck flow saturation

    Energy Technology Data Exchange (ETDEWEB)

    Xing, J.; Sun, X. [Northeastern University, Shenyang (China)

    2007-05-15

    To address current problems in the 'modular dispatch' dynamic programming system widely used in open-pit truck real-time dispatching, two concepts for meeting production targets and truck flow saturation were proposed. Using truck flow programming and taking into account stochastic factors and transportation distance, truck real-time dispatching was optimised. The method is applicable to both shovel-truck match and mismatching and also to empty and heavy truck dispatching. In an open-pit mine the production efficiency could be increased by between 8% and 18%. 6 refs.

  4. Development of an efficient and compact range extender engine; Entwicklung eines effizienten und kompakten Range-Extender-Motors

    Energy Technology Data Exchange (ETDEWEB)

    Mahr, Bernd; Bassett, Mike; Hall, Jonathan; Warth, Marco [Mahle Powertrain Ltd., Northampton (United Kingdom)

    2011-10-15

    Mahle Powertrain has developed a compact, two-cylinder, spark-ignition engine that is specifically designed to be used as a range extender. Drive-cycle simulations and engine tests indicate that a range-extended vehicle using this engine would achieve a significant reduction in fuel consumption and tail-pipe CO{sub 2} levels. (orig.)

  5. Development of Auto-Stacking Warehouse Truck

    Directory of Open Access Journals (Sweden)

    Kuo-Hsien Hsia

    2018-03-01

    Full Text Available Warehouse automation is a very important issue for the promotion of traditional industries. For the production of larger and stackable products, it is usually necessary to operate a fork-lifter for the stacking and storage of the products by a skilled person. The general autonomous warehouse-truck does not have the ability of stacking objects. In this paper, we develop a prototype of auto-stacking warehouse-truck that can work without direct operation by a skill person. With command made by an RFID card, the stacker truck can take the packaged product to the warehouse on the prior-planned route and store it in a stacking way in the designated storage area, or deliver the product to the shipping area or into the container from the storage area. It can significantly reduce the manpower requirements of the skilled-person of forklift technician and improve the safety of the warehousing area.

  6. Large truck and bus crash facts, 2008. 

    Science.gov (United States)

    2010-03-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2008. Selected crash statistics on passenger : vehicles are also presen...

  7. Scrotal neoplasia: would truck drivers be at greater risk?

    Directory of Open Access Journals (Sweden)

    Daniel Seabra

    2007-08-01

    Full Text Available OBJECTIVE: To analyze how scrotal neoplasias have been managed during the past decade and to question possible factors or professions associated to its presence. MATERIALS AND METHODS: We retrospectively evaluated every case reported from 1995 to 2005 at our hospital. We described the clinical scenario, complementary exams, treatments and outcomes. We also tried to verify if there was any risk, predisposing factors or professions that would explain the cancer origin. RESULTS: Six cases were reviewed. Out of these, three patients were truck drivers. Five of them showed restricted lesions without inguinal lymph nodes enlargement. Histologically, six patients presented squamous carcinoma, with two of them having the verrucous type. The median age of patients was 52 years old (31 to 89. The five patients who are still alive had their lesions completely removed with safety margin and primary closure. CONCLUSIONS: We have noticed that the scrotal carcinoma behavior is similar to that of the penis, where removal of the lesion and study of the regional lymph nodes help to increase the patient survival rate. The outstanding fact was that three out of six patients were truck drivers, raising the hypothesis that such profession, maybe due to the contact or attrition with the diesel exhaust expelled by the engine or to sexual promiscuity, would imply in a larger risk of developing this rare neoplasia.

  8. Diesel Engine Technician

    Science.gov (United States)

    Tech Directions, 2010

    2010-01-01

    Diesel engine technicians maintain and repair the engines that power transportation equipment such as heavy trucks, trains, buses, and locomotives. Some technicians work mainly on farm machines, ships, compressors, and pumps. Others work mostly on construction equipment such as cranes, power shovels, bulldozers, and paving machines. This article…

  9. Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas

    Science.gov (United States)

    Tree Biodiesel Truck Transports Capitol Christmas Tree to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas Tree on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas Tree on Twitter Bookmark Alternative

  10. Exhaust Fine Particle and Nitrogen Oxide Emissions from Individual Heavy-Duty Trucks at the Port of Oakland

    Science.gov (United States)

    Dallmann, T. R.; Harley, R. A.; Kirchstetter, T.

    2010-12-01

    Heavy-duty (HD) diesel trucks are a source of nitrogen oxide (NOx) emissions as well as primary fine particulate matter (PM2.5) that includes black carbon (BC) as a major component. Heavy-duty trucks contribute significantly to elevated levels of diesel particulate matter found near highways and in communities surrounding major freight-handling facilities. To reduce the air quality impact of diesel engine emissions, the California Air Resources Board has adopted new rules requiring the retrofit or replacement of in-use HD trucks. These rules take effect during 2010 at ports and railyards, and apply to all trucks operating in California by 2014. This study involves on-road measurements of PM2.5, BC, and NOx emission factor distributions from individual HD trucks driving into the Port of Oakland in the San Francisco Bay area. Measurements of exhaust plumes from individual trucks were made using a mobile laboratory equipped with fast time response (1 Hz) PM2.5, BC, NOx, and carbon dioxide (CO2) sensors. The mobile laboratory was stationed on an overpass above an arterial roadway that connects the Port to a nearby highway (I-880). The air sampling inlet was thereby located above the vertical exhaust pipes of HD diesel trucks passing by on the arterial roadway below. Fuel-specific PM2.5, BC, and NOx emission factors for individual trucks were calculated using a carbon balance method in which concentrations of these species in an exhaust plume are normalized to CO2 concentrations. Initial field sampling was conducted in November, 2009 prior to the implementation of new emission rules. Additional emission measurements were made at the same location during June 2010 and emission factor distributions and averages will be compared.

  11. An Exciting Experiment for Pre-Engineering and Introductory Physics Students: Creating a DC Motor Using the Lorentz Force

    Science.gov (United States)

    Abdul-Razzaq, Wathiq N.; Boehm, Manfred H.; Bushey, Ryan K.

    2008-01-01

    Introductory physics laboratories have been demonstrated in some instances to be difficult or uninteresting to students at the collegiate level. We have developed a laboratory that introduces the concept of the Lorentz force and allows students to build a non-traditional DC motor out of easily acquired materials. Basic electricity and magnetism…

  12. Case Study: Natural Gas Regional Transport Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Laughlin, M.; Burnham, A.

    2016-08-01

    Learn about Ryder System, Inc.'s experience in deploying nearly 200 CNG and LNG heavy-duty trucks and construction and operation of L/CNG stations using ARRA funds. Using natural gas in its fleet, Ryder mitigated the effects of volatile fuel pricing and reduced lifecycle GHGs by 20% and petroleum by 99%.

  13. Light Duty Truck Characteristics, Historical Data Base

    Science.gov (United States)

    1979-12-01

    The report is a collection of data concerning physical, operating, performance, and market characteristics of light duty trucks for the model years 1972 and 1975 thru 1977. The data is stored on tape in DOT/TSC DEC System 10 computer system. Informat...

  14. Light Truck Characteristics, Historical Data Base

    Science.gov (United States)

    1980-11-01

    The report is a description of the data about the physical, operating performance, and market characteristics of light trucks for the model years 1955 through 1977, which is stored on tape in DOT/TSC DEC System 10 computer system. Vehicles are report...

  15. INTRALOG, intelligent autonomous truck applications in Logistics

    NARCIS (Netherlands)

    MSc Berry Gerrits; Dr. Frans Tillema; MMC A.F. Spruijt; MSc Leo Buning

    2016-01-01

    INTRALOG is a project, to better use of materials, there by leading to improvements for People (better safety, lower physical work load), Planet (lower emissions and energy/ fuel con started September 2015, in which Automated Guided Truck Applications will be developed. Automated systems typically

  16. Impact of Paint Color on Rest Period Climate Control Loads in Long-Haul Trucks: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Lustbader, J.; Kreutzer, C.; Jeffers, M.; Adelman, S.; Yeakel, S.; Brontz, P.; Olson, K.; Ohlinger, J.

    2014-02-01

    Cab climate conditioning is one of the primary reasons for operating the main engine in a long-haul truck during driver rest periods. In the United States, sleeper cab trucks use approximately 667 million gallons of fuel annually for rest period idling. The U.S. Department of Energy's National Renewable Energy Laboratory's (NREL) CoolCab Project works closely with industry to design efficient thermal management systems for long-haul trucks that minimize engine idling and fuel use while maintaining occupant comfort. Heat transfer to the vehicle interior from opaque exterior surfaces is one of the major heat pathways that contribute to air conditioning loads during long-haul truck daytime rest period idling. To quantify the impact of paint color and the opportunity for advanced paints, NREL collaborated with Volvo Group North America, PPG Industries, and Dometic Environmental Corporation. Initial screening simulations using CoolCalc, NREL's rapid HVAC load estimation tool, showed promising air-conditioning load reductions due to paint color selection. Tests conducted at NREL's Vehicle Testing and Integration Facility using long-haul truck cab sections, 'test bucks,' showed a 31.1% of maximum possible reduction in rise over ambient temperature and a 20.8% reduction in daily electric air conditioning energy use by switching from black to white paint. Additionally, changing from blue to an advanced color-matched solar reflective blue paint resulted in a 7.3% reduction in daily electric air conditioning energy use for weather conditions tested in Colorado. National-level modeling results using weather data from major U.S. cities indicated that the increase in heating loads due to lighter paint colors is much smaller than the reduction in cooling loads.

  17. Model based control for waste heat recovery rankine cycle system in heavy duty trucks

    OpenAIRE

    Grelet, Vincent; Dufour, Pascal; Nadri, Madiha; Lemort, Vincent; Reiche, Thomas

    2015-01-01

    Driven by future emissions legislations and increase in fuel prices engine, gas heat recovering has recently attracted a lot of interest. In the past few years, a high number of studies have shown the interest of energy recovery Rankine based systems for heavy duty trucks engine compounding. Recent studies have brought a significant potential for such a system in a Heavy Duty (HD) vehicle, which can lead to a decrease in fuel consumption of about 5% [Wang et al. (2011)] and reduce engine emis...

  18. Analisa Penerapan Sistem Hybrid Pada Kapal KPC-28 Dengan Kombinasi Diesel Engine dan Motor Listrik Yang Disuplai Dengan Batterai

    Directory of Open Access Journals (Sweden)

    Tangguh Tangguh Bimantoro

    2014-03-01

    Full Text Available Teknologi Hybrid System Vessel akhir-akhir ini sedang menjadi bahasan yang sering dibicarakan di dunia pendidikan dan teknologi permesinan. Teknologi Hybrid System Vessel yang dimaksud adalah kapal yang berjalan dengan dua sumber tenaga, mesin yang bekerja dengan sumber tenaga bahan bakar dan motor listrik yang bekerja dengan sumber tenaga listrik. Oleh karena adanya permasalahan tersebut maka dikembangkanlah konsep system hybrid pada kapal.Hybrid ini mengacu teknologi pada mobil hybrid yang sudah dikembangkan sekarang, tujuan dari hybrid ini adalah sebagai penghematan BBM dan juga sebagai pereduksi emisi di system permesinan kapal.Penelitian ini menggunakan simulasi dengan software Maxsurf, kemudian dilakukan dengan metode perhitungan manual yang nantinya digunakan untuk menentukan jumlah batterai yang dibutuhkan pada penggerak motor induksi. Hasil dari penelitian ini berupa desain  Hybrid System kapal KPC – 28, serta hasil analisa Hybrid System di kapal apakah memberikan effisiensi bahan bakar yang cukup hemat dengan tanpa menggunakan Hybrid System pada mesin kapal tersebut.

  19. An exciting experiment for pre-engineering and introductory physics students: creating a DC motor using the Lorentz force

    International Nuclear Information System (INIS)

    Abdul-Razzaq, Wathiq N; Boehm, Manfred H; Bushey, Ryan K

    2008-01-01

    Introductory physics laboratories have been demonstrated in some instances to be difficult or uninteresting to students at the collegiate level. We have developed a laboratory that introduces the concept of the Lorentz force and allows students to build a non-traditional DC motor out of easily acquired materials. Basic electricity and magnetism concepts are joined together in a simple and enjoyable experiment that allows the students to demonstrate physics at first hand and without the use of complex materials

  20. Impacts of Aging Emission Control Systems on In-Use Heavy-Duty Diesel Truck Emission Rates

    Science.gov (United States)

    Preble, C.; Cados, T.; Harley, R.; Kirchstetter, T.

    2017-12-01

    Heavy-duty diesel trucks are a major source of nitrogen oxides (NOx) and black carbon (BC) in urban environments, contributing to persistent ozone and particulate matter air quality problems. Recently, diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems have become standard equipment on new trucks. Particle filters can also be installed as a retrofit on older engines. Prior work has shown that exhaust filters and SCR systems effectively reduce BC and NOx emission rates by up to 90 and 80%, respectively (Preble et al., ES&T 2015). There is concern, however, that DPFs may promote the formation of ultrafine particles (UFP) and increase tailpipe emissions of nitrogen dioxide (NO2). Additionally, urea-based SCR systems for NOx control may form nitrous oxide (N2O), an important contributor to stratospheric ozone depletion. The effectiveness of these emission controls has been thoroughly evaluated in the laboratory, but the long-term durability of in-use systems and their impacts on co-emitted species have not been well characterized. To evaluate the in-use performance of DPF and SCR systems, pollutant emissions from thousands of diesel trucks were measured over several years at the Port of Oakland and the Caldecott Tunnel in the San Francisco Bay Area. Pollutants present in the exhaust plumes of individual trucks were measured at high time resolution (≥1 Hz) as trucks passed under a mobile lab stationed on an overpass. Fuel-based emission factors (g pollutant emitted per kg fuel burned) were calculated for individual trucks and linked via recorded license plates to vehicle attributes, including engine model year and installed emission control systems. Use of DPFs reduced the BC emission rate by up to 95% at both locations. SCR systems were more effective at reducing NOx emissions under the uphill, highway driving conditions at the Caldecott Tunnel. The emission rates of co-emitted species NO2, UFP, and N2O depended on driving

  1. An optimal power management system for a regenerative auxiliary power system for delivery refrigerator trucks

    International Nuclear Information System (INIS)

    Mohagheghi Fard, Soheil; Khajepour, Amir

    2016-01-01

    Highlights: • A new anti-idling system for refrigerator trucks is proposed. • This system enables regenerative braking. • An innovative two-level controller is proposed for the power management system. • A fast dynamic programming technique to find real-time SOC trajectory is proposed. • In addition to idling elimination, this system reduces fuel consumption. - Abstract: Engine idling of refrigerator trucks during loading and unloading contributes to greenhouse gas emissions due to their increased fuel consumption. This paper proposes a new anti-idling system that uses two sources of power, battery and engine-driven generator, to run the compressor of the refrigeration system. Therefore, idling can be eliminated because the engine is turned OFF and the battery supplies auxiliary power when the vehicle is stopped for loading or unloading. This system also takes advantage of regenerative braking for increased fuel savings. The power management of this system needs to satisfy two requirements: it must minimize fuel consumption in the whole cycle and must ensure that the battery has enough energy for powering the refrigeration system when the engine is OFF. To meet these objectives, a two-level controller is proposed. In the higher level of this controller, a fast dynamic programming technique that utilizes extracted statistical features of drive and duty cycles of a refrigerator truck is used to find suboptimal values of the initial and final SOC of any two consecutive loading/unloading stops. The lower level of the controller employs an adaptive equivalent fuel consumption minimization (A-ECMS) to determine the split ratio of auxiliary power between the generator and battery for each segment with initial and final SOC obtained by the high-level controller. The simulation results confirm that this new system can eliminate idling of refrigerator trucks and reduce their fuel consumption noticeably such that the cost of replacing components is recouped in a

  2. Desempenho comparativo de um motor de ciclo diesel utilizando diesel e misturas de biodiesel Comparative performance of a cycle diesel engine using diesel and biodiesel mixtures

    Directory of Open Access Journals (Sweden)

    Ronald Leite Barbosa

    2008-10-01

    fixation of man country life, the excellent and varied climatic conditions and several types of terrain become the country, with extensive workable areas, stand out in the world scenery if considering its great potentiality on generation of alternative fuels. The environmental preservation, important subject nowadays, makes that the human being work in searches for the development of alternative energies, mainly those originating from renewable and biodegradable sources of sustantable character. Taking in consideration those searches, the purpose of this work was to evaluate the performance of a diesel engine working in different moments with mineral diesel and mixtures of mineral diesel and biodiesel in the equivalent proportions B2 (98% mineral diesel and 2%biodiesel, B5 (95% mineral diesel and 5%biodiesel, B20 (80% mineral diesel and 20%biodiesel, and, finally, B100 (100% biodiesel. The rehearsal was accomplished in the dependences of the Engineering Department at UFLA - Federal University of Lavras, in Lavras, Minas Gerais, in July, 2005. For the accomplishment of the rehearsals it, was used an engine cycle diesel of a tractor VALMET 85 id, of 58,2kW (78 cv, following it methodology established by the norm NBR 5484 of ABNT (1985, that refers to the rehearsal dynamometric of engines cycle Otto and Diesel being proceeded. One noticed ended that the potency of the motor when using biodiesel was lower than one when using mineral diesel. One observed that, in some rotations, the mixtures B5 and B20 presented the same potency or even higher, in some situations, than the one when if using mineral diesel. The best thermal efficiency of the motor was verified in the rotation of 540 rpm of equivalent TDP to 1720 rpm of the motor.

  3. 2015 E-Truck Task Force: Key Barriers Affecting E-Truck Adoption, Industry and Policy Implications, and Recommendations to Move the Market Forward

    OpenAIRE

    Brotherton, Tom; Gilde, Alycia; Tomic, Jasna

    2016-01-01

    CALSTART’s E-Truck Task Force (ETTF) produced a report outlining the markets for electric drive trucks (E-Trucks), the prime barriers facing their success and provided key findings and recommendations to support expanding E-Truck adoption. Four key findings have been identified by the E-Truck Task Force as barriers currently affecting the growth and viability of E-Truck sales

  4. 49 CFR 542.1 - Procedures for selecting new light duty truck lines that are likely to have high or low theft rates.

    Science.gov (United States)

    2010-10-01

    ... lines that are likely to have high or low theft rates. 542.1 Section 542.1 Transportation Other... OF TRANSPORTATION PROCEDURES FOR SELECTING LIGHT DUTY TRUCK LINES TO BE COVERED BY THE THEFT... or low theft rates. (a) Scope. This section sets forth the procedures for motor vehicle manufacturers...

  5. 49 CFR Appendix B to Part 541 - Light Duty Truck Lines With Theft Rates Below the 1990/91 Median Theft Rate, Subject to the...

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 6 2010-10-01 2010-10-01 false Light Duty Truck Lines With Theft Rates Below the 1990/91 Median Theft Rate, Subject to the Requirements of This Standard B Appendix B to Part 541... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR VEHICLE THEFT PREVENTION STANDARD Pt. 541, App. B...

  6. Perfiles de Velocidad en el Cilindro de un Motor Alternativo Velocity Profiles in an Alternative Engine Cilinder

    OpenAIRE

    Simón J Fygueroa; Jesús O Araque; Carlos G Villamar

    2007-01-01

    El objetivo del presente trabajo es mostrar los resultados de la medición de las componentes de la velocidad del aire admitido en el cilindro simulado de un motor CFR (Cooperative Fuels Research) instalado en un banco de flujo estacionario al cual se ha conectado un sistema de adquisición de datos. Para determinar las velocidades se empleó un anemómetro de hilo caliente previamente calibrado. Se realizaron mediciones sobre diferentes puntos de varios planos transversales del cilindro para dif...

  7. Dump truck-related deaths in construction, 1992-2007.

    Science.gov (United States)

    McCann, Michael; Cheng, Mei-Tai

    2012-05-01

    Dump trucks are universally used in construction and other industries to haul materials to the location and to remove waste materials. The source for dump truck-related fatality data was the Bureau of Labor Statistics Census of Fatal Occupational Injuries (CFOI) Research File. From 1992 to 2007, 829 construction workers were killed in dump truck-related incidents nationwide. Of those, 336 were dump truck operators with 215 deaths occurring in street and highway incidents. Another 343 deaths involved workers on foot, three-quarters struck by dump trucks. Sixty-four of the construction workers killed were maintaining dump trucks, 22 when caught between the truck frame and a falling dump truck bed. Of the 86 other deaths, 55 involved streets and highways. Recommendations include: (i) improving the reporting of seat belt usage in fatality reports; (ii) requiring use of seat belts; (iii) requiring the use of backup alarms, spotters, or other methods to alert dump truck operators to workers in their blind spots; (iv) prohibiting direct dumping at river banks and embankments; (v) using cameras or radar to enforce stopping at railway crossings; and (xi) enforcing worker safety practices (e.g., lockout/tagout procedures on elevated dump truck beds). Copyright © 2011 Wiley Periodicals, Inc.

  8. N2O and NO2 Emissions from Heavy-Duty Diesel Trucks with Advanced Emission Controls

    Science.gov (United States)

    Preble, C.; Harley, R.; Kirchstetter, T.

    2014-12-01

    Diesel engines are the largest source of nitrogen oxides (NOx) emissions nationally, and also a major contributor to the black carbon (BC) fraction of fine particulate matter (PM). Recently, diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems that target exhaust PM and NOx have become standard equipment on new heavy-duty diesel trucks. However, the deliberate catalytic oxidation of engine-out nitric oxide (NO) to nitrogen dioxide (NO2) in continuously regenerating DPFs leads to increased tailpipe emission of NO2. This is of potential concern due to the toxicity of NO2 and the resulting increases in atmospheric formation of other air pollutants such as ozone, nitric acid, and fine PM. While use of SCR reduces emissions of both NO and NO2, it may lead to increased emissions of nitrous oxide (N2O), a potent greenhouse gas. Here we report results from on-road measurements of heavy-duty diesel truck emissions conducted at the Port of Oakland and the Caldecott Tunnel in the San Francisco Bay Area. Emission factors (g pollutant per kg of diesel) were linked via recorded license plates to individual truck attributes, including engine model year and installed emission control equipment. Between 2009 and 2013, the fraction of DPF-equipped trucks at the Port of Oakland increased from 2 to 99%, and median engine age decreased from 11 to 6 years. Over the same period, fleet-average emission factors for black carbon and NOx decreased by 76 ± 22% and 53 ± 8%, respectively. However, direct emissions of NO2 increased, and consequently the NO2/NOx emission ratio increased from 0.03 ± 0.02 to 0.18 ± 0.03. Older trucks retrofitted with DPFs emitted approximately 3.5 times more NO2 than newer trucks equipped with both DPF and SCR. Preliminary data from summer 2014 measurements at the Caldecott Tunnel suggest that some older trucks have negative emission factors for N2O, and that for newer trucks, N2O emission factors have changed sign and

  9. Prospects of development of land driverless trucks

    Science.gov (United States)

    Bakhmutov, S.; Saykin, A.; Endachev, D.; Evgrafov, V.; Shagurin, A.; Kulikov, I.; Fedoseev, K.

    2018-02-01

    The paper is dedicated to the problem of creation and efficient use of driverless trucks. It also contains general analysis of foreign experience and development trends. The concept of FSUE “NAMI” for development of a platoon of driverless trucks for cargo transportation between specialized terminals on public roads is provided. A road train with virtual couplings where the lead vehicle has a driver and the rest are driverless is proposed as a base for the driverless platoon. The platoon is formed by such road trains, which ensures extended functional features, including the possibility to form platoons of road trains from different logistics centers and with different destinations, quick reforming of the platoon in the logistics centers, possibility to split the platoon when driving on public roads, higher precision of control over the platoon during driving, etc. It is also shown that in order to improve the efficiency of cargo transportation, driverless cargo platforms (trucks) shall be designed without a cabin. The paper also considers the ways to reduce the price of driverless trucks by creating a special road infrastructure, which will allow transfer of the most expensive subsystems of driverless vehicles to such infrastructure. Upon that, the following subsystems will remain within the driverless chassis: navigation, communication, chassis control and ADAS. It is noted that creation of such infrastructure will require high investments, therefore, gradual implementation of such systems is seen as rational. It is shown that the most appropriate area for these purposes is transregional cargo transportation. It is noted that the economic reasons for implementation of the proposed concept are as follows: significant reduction of the number of drivers; significant simplification of the driverless platform control system and reduction of the price of subsystems; no need for the driver’s cabin within the driverless platform; fuel economy when driving within a

  10. Motor vehicle fuel economy, the forgotten HC control stragegy. [Hydrocarbon (HC)

    Energy Technology Data Exchange (ETDEWEB)

    Deluchi, M.; Wang, Quanlu; Greene, D.L.

    1992-06-01

    Emissions of hydrocarbons from motor vehicles are recognized as major contributors to ozone pollution in urban areas. Petroleum-based motor fuels contain volatile organic compounds (VOC) which, together with oxides of nitrogen, promote the formation of ozone in the troposphere via complex photochemical reactions. VOC emissions from the tailpipe and evaporation from the fuel and engine systems of highway vehicles are believed to account for about 40% of total VOC emissions in any region. But motor fuels also generate emissions throughout the fuel cycle, from crude oil production to refining, storage, transportation, and handling, that can make significant contributions to the total inventory of VOC emissions. Many of these sources of emissions are directly related to the quantity of fuel produced and handled throughout the fuel cycle. It is, therefore, reasonable to expect that a reduction in total fuel throughput might result in a reduction of VOC emissions. In particular, reducing vehicle fuel consumption by increasing vehicle fuel economy should reduce total fuel throughput, thereby cutting total emissions of VOCS. In this report we identify the sources of VOC emissions throughout the motor fuel cycle, quantify them to the extent possible, and describe their dependence on automobile and light truck fuel economy.

  11. Real world efficiency of retrofit partial-flow diesel particulate filters for trucks

    International Nuclear Information System (INIS)

    Van Asch, R.; Verbeek, R.; Ligterink, N.; Kadijk, G.

    2009-11-01

    In 2006 the Dutch Ministry of Housing, Spatial Planning and the Environment (VROM) introduced an incentive scheme for retrofitting diesel particulate filters on Euro II and Euro III trucks. This scheme involves both partial flow and full flow diesel particulate filters (also called semi-open or open respectively wall-flow or closed filters). In the period 2007 till January 2009 about 15,000 partial flow filters and 8,000 full flow diesel particulate filters were installed. The minimum filtration efficiency requirement for the partial flow diesel particulate filters is 50% during the type approval test. In 2008 an engine dynamometer test programme was conducted to measure the filtration efficiency of retrofit open particulates filters of heavy trucks. This led to somewhat disappointing results with average filtration efficiencies in the range of 5-20% during city and national motorway driving conditions up to 20-40% during long distance motorway driving. This result leads to two main questions: (1) Is this result also representative for medium heavy trucks used for delivery, and (2) do similar efficiencies show up also in tests on entire vehicles, tested under conditions as close as possible to their real world usage profile. To this end, an additional measurement programme was defined, which is reported here. The objective of the study reported here is to determine the real world filtration efficiency of retrofit partial flow particulate filters for a number of trucks under different driving conditions such as city and motorway driving. The emphasis should be on medium heavy trucks typically used for national delivery.

  12. COMPUTATIONAL AND EXPERIMENTAL EVALUATION OF TECHNICAL CHARACTERISTICS OF TRUCKS TIRES

    Directory of Open Access Journals (Sweden)

    Z. A. Godzhaev

    2015-01-01

    Full Text Available Now improvement of technological design specification of trucks tires develops very much. In modern mechanical engineering polyamide and kapron cords for tires of line-haul trucks and buses are replaced with all-metal ones (AMC even more often. It was defined that at increase in AMC tires production their technical characteristics were investigated insufficiently. In this regard there were carried out bench tests to compare the main operational indicators of domestic (JSC Nizhnekamskshina production and foreign tires with an all-metal cord: 315/60R22.5 the NF-201 model with 315/60r22.5 the XZA2 ENERGY Michelin model (steering; 315/60R22.5 the NR-201 model with 315/60R22.5 the XDA2+ ENERGY Michelin model (drive; 315/80R22.5 the NF-201 model with 315/80R22.5 the 3D Michelin XZE X MultiWay model (steering; 315/80R22.5 the NR-201 model with 315/80R22.5 the 3D XDE X MultiWay model (drive. The laboratory researches were carried out for the purpose of an assessment of the universal, load, damping (hysteresis and other characteristics of tires with use of the universal functional SIB-1M test-bench. It was established that Michelin AMC tires of steering low-profile 315/60R22.5 XZA2 ENERGY models have the best indicators on power heterogeneity - 0.47-0.89 percent. The high-profile AMC tires of drive wheels 315/80R22.5 of the NR-201 model of JSC Nizhnekamskshina have the worst indicators. However, all the tested tires correspond to GOST 5513-97on this indicator. It was noted that Nizhnekamsk AMC tires of the size 315/60R22.5 are flush with AMC tires Michelin on set of operational indicators, except power heterogeneity, and last one of Michelin tires is lower than Nizhnekamsk ones by 2-3 times. It was suggested to conduct further researches on definition of optimum operational tires indicators because of an intensive use of KAMAZ trucks in agricultural production

  13. Mechanical design of electric motors

    CERN Document Server

    Tong, Wei

    2014-01-01

    Rapid increases in energy consumption and emphasis on environmental protection have posed challenges for the motor industry, as has the design and manufacture of highly efficient, reliable, cost-effective, energy-saving, quiet, precisely controlled, and long-lasting electric motors.Suitable for motor designers, engineers, and manufacturers, as well as maintenance personnel, undergraduate and graduate students, and academic researchers, Mechanical Design of Electric Motors provides in-depth knowledge of state-of-the-art design methods and developments of electric motors. From motor classificati

  14. n-Heptane cool flame chemistry: Unraveling intermediate species measured in a stirred reactor and motored engine

    KAUST Repository

    Wang, Zhandong; Chen, Bingjie; Moshammer, Kai; Popolan-Vaida, Denisia M.; Sioud, Salim; Shankar, Vijai; Vuilleumier, David; Tao, Tao; Ruwe, Lena; Brä uer, Eike; Hansen, Nils; Dagaut, Philippe; Kohse-Hö inghaus, Katharina; Raji, Misjudeen; Sarathy, Mani

    2017-01-01

    -OTMS, which has ultra-high mass resolving power and provides an accurate elemental C/H/O composition of the intermediate species. Furthermore, the results show that the species formed during the partial oxidation of n-heptane in the CFR engine are very similar

  15. Level Recession Of Emissions Release By Motor-And-Tractor Diesel Engines Through The Application Of Water-Fuel Emulsions

    Science.gov (United States)

    Ivanov, A.; Chikishev, E.

    2017-01-01

    The paper is dedicated to a problem of environmental pollution by emissions of hazardous substances with the exhaust gases of internal combustion engines. It is found that application of water-fuel emulsions yields the best results in diesels where production of a qualitative carburetion is the main problem for the organization of working process. During pilot studies the composition of a water-fuel emulsion with the patent held is developed. The developed composition of a water-fuel emulsion provides its stability within 14-18 months depending on mass content of components in it while stability of emulsions’ analogues makes 8-12 months. The mode of operation of pilot unit is described. Methodology and results of pilot study of operation of diesel engine on a water-fuel emulsion are presented. Cutting time of droplet combustion of a water-fuel emulsion improves combustion efficiency and reduces carbon deposition (varnish) on working surfaces. Partial dismantling of the engine after its operating time during 60 engine hours has shown that there is a removal of a carbon deposition in cylinder-piston group which can be observed visually. It is found that for steady operation of the diesel and ensuring decrease in level of emission of hazardous substances the water-fuel emulsion with water concentration of 18-20% is optimal.

  16. 40 CFR 1039.605 - What provisions apply to engines certified under the motor-vehicle program?

    Science.gov (United States)

    2010-07-01

    ...) Include your full corporate name and trademark. You may instead include the full corporate name and... corporate name, address, and telephone number. (ii) List the engine or equipment models you expect to... valid certificate of conformity issued under 40 CFR part 86. (2) You must not make any changes to the...

  17. Adaptive Virtual Tow Bar and Transition of Control : A truck driving simulator study

    NARCIS (Netherlands)

    Wilschut, E.S.; Willemsen, D.M.C.; Hogema, J.H.; Martens, M.H.

    2016-01-01

    Background : Truck platooning, with trucks being virtually connected, is getting more and more attention. Truck platooning offers the potential for substantial fuel savings while allowing the truck driver in the platoon to take a rest. However, at the current state of technology, truck drivers are

  18. DESIGN OF EXPERIMENTS IN TRUCK COMPANY

    Directory of Open Access Journals (Sweden)

    Bibiana Kaselyova

    2015-07-01

    Full Text Available Purpose: Design of experiment (DOE represent very powerful tool for process improvement vastly supported by six sigma methodology. This approach is mostly used by large and manufacturing orientated companies. Presented research is focused on use of DOE in truck company, which is medium size and service orientated. Such study has several purposes. Firstly, detailed description of improvement effort based on DOE can be used as a methodological framework for companies similar to researched one. Secondly, it provides example of successfully implemented low cost design of experiment practise. Moreover, performed experiment identifies key factors, which influence the lifetime of truck tyres.Design/methodology: The research in this paper is based on experiment conducted in Slovakian Truck Company. It provides detailed case study of whole improvement effort, together with problem formulation, design creation and analysis, as well as the results interpretation. The company wants to improve lifetime of the truck tyres. Next to fuel consumption, consumption of tyres and their replacement represent according to them, one of most costly processes in company. Improvement effort was made through the use of PDCA cycle. It start with analysis of current state of tyres consumption. The variability of tyres consumption based on years and types was investigated. Then the causes of tyres replacement were identified and screening DOE was conducted. After a screening design, the full factorial design of experiment was used to identify main drivers of tyres deterioration and breakdowns. Based on result of DOE, the corrective action were propose and implement.Findings: Based on performed experiment our research describes process of tyres use and replacement. It defines main reasons for tyre breakdown and identify main drivers which influence truck tyres lifetime. Moreover it formulates corrective action to prolong tyres lifetime.Originality: The study represents full

  19. Plug-In Hybrid Medium-Duty Truck Demonstration and Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Miyasato, Matt [Electric Power Research Institute (EPRI), Palo Alto, CA (United States); Kosowski, Mark [Electric Power Research Institute (EPRI), Palo Alto, CA (United States)

    2015-10-01

    The Plug-In Hybrid Medium-Duty Truck Demonstration and Evaluation Program was sponsored by the United States Department of Energy (DOE) using American Recovery and Reinvestment Act of 2009 (ARRA) funding. The purpose of the program is to develop a path to migrate plug-in hybrid electric vehicle (PHEV) technology to medium-duty vehicles by demonstrating and evaluating vehicles in diverse applications. The program also provided three production-ready PHEV systems—Odyne Systems, Inc. (Odyne) Class 6 to 8 trucks, VIA Motors, Inc. (VIA) half-ton pickup trucks, and VIA three-quarter-ton vans. The vehicles were designed, developed, validated, produced, and deployed. Data were gathered and tests were run to understand the performance improvements, allow cost reductions, and provide future design changes. A smart charging system was developed and produced during the program. The partnerships for funding included the DOE; the California Energy Commission (CEC); the South Coast Air Quality Management District (SCAQMD); the Electric Power Research Institute (EPRI); Odyne; VIA; Southern California Edison; and utility and municipal industry participants. The reference project numbers are DOE FOA-28 award number EE0002549 and SCAQMD contract number 10659.

  20. Truck drivers' traffic accidents in the State of São Paulo: prevalence and predictors.

    Science.gov (United States)

    Oliveira, Lucio Garcia de; Almeida, Carlos Vinícius Dias de; Barroso, Lucia Pereira; Gouvea, Marcela Julio Cesar; Muñoz, Daniel Romero; Leyton, Vilma

    2016-12-01

    Abstract The mortality rate of traffic accidents (TA) is high in Brazil. Trucks are the second category of motor vehicles most often involved in TA. However, few studies have addressed the issue of TA among these professionals. The study aimed to estimate the prevalence of TA and their predictors in a sample of 684 truck drivers recruited in the state of São Paulo during 2012 and 2013. We requested participants to answer a research instrument on their personal and occupational data and their involvement in TA and traffic violations. A logistic regression model was developed to identify TA predictors. Almost 11% of the respondents suffered at least one TA in that timeframe. We identified the following TA predictors: having few years of experience as professional drivers (OR = 1.86; CI 95% = 1.05-3.38; p = 0.036); receiving some traffic tickets (OR = 1.91; CI 95% = 1.04-3.66; p = 0.043) and working more than 12 hours daily (OR = 1.84; CI 95% = 1.04-3.24; p = 0.034). Given those results, we suggest the development of a joint action among all the involved social stakeholders in order to negotiate truck drivers' work organization aiming at reducing behaviors that may lead to traffic accidents.

  1. Human Resource Development and New Technology in the Automobile Industry: A Case Study of Ford Motor Company's Dearborn Engine Plant. The Development and Utilization of Human Resources in the Context of Technological Change and Industrial Restructuring.

    Science.gov (United States)

    Chen, Kan; And Others

    This report centers around a plant-level study of the development and utilization of human resources in the context of technological change and industrial restructuring in the crankshaft production area of Ford Motor Company's Dearborn Engine Plant (DEP). The introductory chapter describes how the study was conducted, provides an introduction to…

  2. System for selection of radiation source transfer trucks

    International Nuclear Information System (INIS)

    Tanimoto, Yoshinori; Ito, Kojiro.

    1970-01-01

    A device for selection of trucks each of which load and transfer a radiation source to an irradiation room above a water pool is installed at the end of a pair of rails fixed to the bottom of the pool. This device is equipped with a number of laterally shiftable rail pairs which may be brought into successive alignment with the fixed rails and is adapted to receive, carry and fix a truck on each rail pair. If one of said trucks is selected for irradiation in a desired irradiation room, the rail pair carrying this truck is shifted to align and couple with the fixed rail pair whereupon the truck is driven and transferred to a position on the fixed rails below the desired room and elevated thereinto. Accordingly, a plurality of trucks can optionally be shunted on a line of fixed rails without unloading the respective radiation sources. (Ohno, Y.)

  3. Diagnostico de un motor de gasolina de cuatro cilindros mediante el análisis de vibraciones//Diagnostic of a four cylinder gasoline engine using vibration analysis

    Directory of Open Access Journals (Sweden)

    Jairo Andrés-Grajales

    2015-09-01

    Full Text Available Este trabajo presenta el análisis de vibraciones de un motor de combustión interna, operando con diferentes mezclas de combustible, para identificar condiciones de operación con falla, utilizando un banco de pruebas y la falla estudiada fue el “misfire”. Tres mezclas de combustible fueron probadas: E8, E20 y E30. Aplicando la transformada rápida de Fourier a las señales, se compararon las condiciones de operación normal y con falla entre combustibles, buscando componentes de frecuencia característicos para evaluar la validez de los estudios realizados hasta ahora en gasolina pura. Los resultados muestran que el comportamiento utilizando las diferentes mezclas de combustible es similar al reportado con gasolina pura, y los componentes de frecuencia que diferencian la condición normal y con falla también están presentes en las mezclas de combustible. Se extrajeron características estadísticas de las señales en el dominio de la frecuencia para simplificar el proceso de identificación. Palabras clave: motor de combustión interna, vibraciones, detección de fallas, problema de encendido, mezclas gasolina-etanol.______________________________________________________________________________AbstractThis paper presents the vibration analysis of an internal combustion engine, using different fuel blends, to identify fault operating conditions. A purpose built engine test bench was used and the fault studied was misfire. Three fuel blends were used: E8, E20 and E30. Fast Fourier transform was applied to the signals. A comparison between normal and faulty operating conditions was carried with every fuel used, looking for characteristic frequency components, to assess the validity of past studies on misfire performed on pure gasoline. The results show that the behavior using the different fuel blends is similar to the one reported on pure gasoline, and that the frequency components that differentiate normal and faulty conditions are also

  4. Improving truck safety: Potential of weigh-in-motion technology

    Directory of Open Access Journals (Sweden)

    Bernard Jacob

    2010-07-01

    Full Text Available Trucks exceeding the legal mass limits increase the risk of traffic accidents and damage to the infrastructure. They also result in unfair competition between transport modes and companies. It is therefore important to ensure truck compliance to weight regulation. New technologies are being developed for more efficient overload screening and enforcement. Weigh-in-Motion (WIM technologies allow trucks to be weighed in the traffic flow, without any disruption to operations. Much progress has been made recently to improve and implement WIM systems, which can contribute to safer and more efficient operation of trucks.

  5. Development and Implementation of a Battery-Electric Light-Duty Class 2a Truck including Hybrid Energy Storage

    Science.gov (United States)

    Kollmeyer, Phillip J.

    This dissertation addresses two major related research topics: 1) the design, fabrication, modeling, and experimental testing of a battery-electric light-duty Class 2a truck; and 2) the design and evaluation of a hybrid energy storage system (HESS) for this and other vehicles. The work begins with the determination of the truck's peak power and wheel torque requirements (135kW/4900Nm). An electric traction system is then designed that consists of an interior permanent magnet synchronous machine, two-speed gearbox, three-phase motor drive, and LiFePO4 battery pack. The battery pack capacity is selected to achieve a driving range similar to the 2011 Nissan Leaf electric vehicle (73 miles). Next, the demonstrator electric traction system is built and installed in the vehicle, a Ford F150 pickup truck, and an extensive set of sensors and data acquisition equipment is installed. Detailed loss models of the battery pack, electric traction machine, and motor drive are developed and experimentally verified using the driving data. Many aspects of the truck's performance are investigated, including efficiency differences between the two-gear configuration and the optimal gear selection. The remainder focuses on the application of battery/ultracapacitor hybrid energy storage systems (HESS) to electric vehicles. First, the electric truck is modeled with the addition of an ultracapacitor pack and a dc/dc converter. Rule-based and optimal battery/ultracapacitor power-split control algorithms are then developed, and the performance improvements achieved for both algorithms are evaluated for operation at 25°C. The HESS modeling is then extended to low temperatures, where battery resistance increases substantially. To verify the accuracy of the model-predicted results, a scaled hybrid energy storage system is built and the system is tested for several drive cycles and for two temperatures. The HESS performance is then modeled for three variants of the vehicle design, including the

  6. Naturalistic drive cycle synthesis for pickup trucks.

    Science.gov (United States)

    Liu, Zifan; Ivanco, Andrej; Filipi, Zoran

    2015-09-01

    Future pick-up trucks are meeting much stricter fuel economy and exhaust emission standards. Design tradeoffs will have to be carefully evaluated to satisfy consumer expectations within the regulatory and cost constraints. Boundary conditions will obviously be critical for decision making: thus, the understanding of how customers are driving in naturalistic settings is indispensable. Federal driving schedules, while critical for certification, do not capture the richness of naturalistic cycles, particularly the aggressive maneuvers that often shape consumer perception of performance. While there are databases with large number of drive cycles, applying all of them directly in the design process is impractical. Therefore, representative drive cycles that capture the essence of the naturalistic driving should be synthesized from naturalistic driving data. Naturalistic drive cycles are firstly categorized by investigating their micro-trip components, defined as driving activities between successive stops. Micro-trips are expected to characterize underlying local traffic conditions, and separate different driving patterns. Next, the transitions from one vehicle state to another vehicle state in each cycle category are captured with Transition Probability Matrix (TPM). Candidate drive cycles can subsequently be synthesized using Markov Chain based on TPMs for each category. Finally, representative synthetic drive cycles are selected through assessment of significant cycle metrics to identify the ones with smallest errors. This paper provides a framework for synthesis of representative drive cycles from naturalistic driving data, which can subsequently be used for efficient optimization of design or control of pick-up truck powertrains. Manufacturers will benefit from representative drive cycles in several aspects, including quick assessments of vehicle performance and energy consumption in simulations, component sizing and design, optimization of control strategies, and

  7. Differences in passenger car and large truck involved crash frequencies at urban signalized intersections: an exploratory analysis.

    Science.gov (United States)

    Dong, Chunjiao; Clarke, David B; Richards, Stephen H; Huang, Baoshan

    2014-01-01

    The influence of intersection features on safety has been examined extensively because intersections experience a relatively large proportion of motor vehicle conflicts and crashes. Although there are distinct differences between passenger cars and large trucks-size, operating characteristics, dimensions, and weight-modeling crash counts across vehicle types is rarely addressed. This paper develops and presents a multivariate regression model of crash frequencies by collision vehicle type using crash data for urban signalized intersections in Tennessee. In addition, the performance of univariate Poisson-lognormal (UVPLN), multivariate Poisson (MVP), and multivariate Poisson-lognormal (MVPLN) regression models in establishing the relationship between crashes, traffic factors, and geometric design of roadway intersections is investigated. Bayesian methods are used to estimate the unknown parameters of these models. The evaluation results suggest that the MVPLN model possesses most of the desirable statistical properties in developing the relationships. Compared to the UVPLN and MVP models, the MVPLN model better identifies significant factors and predicts crash frequencies. The findings suggest that traffic volume, truck percentage, lighting condition, and intersection angle significantly affect intersection safety. Important differences in car, car-truck, and truck crash frequencies with respect to various risk factors were found to exist between models. The paper provides some new or more comprehensive observations that have not been covered in previous studies. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. Hydrogen in motor car engineering. Production, storage, use. 3. rev. ed.; Wasserstoff in der Fahrzeugtechnik. Erzeugung, Speicherung, Anwendung

    Energy Technology Data Exchange (ETDEWEB)

    Eichlseder, Helmut [Technische Univ., Graz (Austria). Inst. fuer Verbrennungskraftmaschinen und Thermodynamik; Klell, Manfred [HyCentA Research GmbH, Graz (Austria)

    2012-07-01

    The book outlines the various aspects of properties, generation, storage and uses of hydrogen. The focus is on the thermodynamics of hydrogen storage and on its applications in vehicle engineering and energy engineering. Using the example of current research projects of TU Graz university and HyCentA, the state of the art is presented in some detail. The sections on fuel cells for automotive power generation, hydrogen/methane mixtures and legal and safety aspects have been updated. [German] Dieses Buch bietet einen allgemeinen Ueberblick ueber die verschiedenen Aspekte von Eigenschaften, Erzeugung, Speicherung und Anwendung von Wasserstoff. Schwerpunkte liegen auf der Thermodynamik der Speicherung von Wasserstoff sowie auf der Anwendung in der Fahrzeugtechnik und in der Energietechnik. Mit Bezug zu Forschungsvorhaben an der TU Graz und dem HyCentA wird der aktuelle Stand der Technik fundiert dargestellt. Aktualisiert und ergaenzt wurden vor allem die Abschnitte ueber Brennstoffzellen zur Stromerzeugung fuer Elektroantriebe, ueber Gemische aus Wasserstoff und Methan sowie ueber Fragen von Recht und Sicherheit.

  9. Modernization of dump truck onboard system

    Science.gov (United States)

    Semenov, M. A.; Bolshunova, O. M.; Korzhev, A. A.; Kamyshyan, A. M.

    2017-10-01

    The review of the only automated dispatch system for the career dump trucks, which is presented in the domestic market, was made. A method for upgrading the loading control system and technological weighing process of the career dump was proposed. The cargo weight during loading is determined by the gas pressure in the suspension cylinders at the time of the oscillation ending and at the start of the vibration smoothing process; the smoothing speed correction is performed. The error of the cargo weighting is 2.5-3%, and of the technological weighing process during driving - 1%, which corresponds to the error level of the steady-state weighting means.

  10. Motor Neurons

    DEFF Research Database (Denmark)

    Hounsgaard, Jorn

    2017-01-01

    Motor neurons translate synaptic input from widely distributed premotor networks into patterns of action potentials that orchestrate motor unit force and motor behavior. Intercalated between the CNS and muscles, motor neurons add to and adjust the final motor command. The identity and functional...... in in vitro preparations is far from complete. Nevertheless, a foundation has been provided for pursuing functional significance of intrinsic response properties in motoneurons in vivo during motor behavior at levels from molecules to systems....

  11. Induction Machine with Improved Operating Performances for Electric Trucks. A FEM-Based Analysis

    Directory of Open Access Journals (Sweden)

    MUNTEANU, A.

    2010-05-01

    Full Text Available The paper presents a study concerning the performance developed by induction motors destined for motorization of heavy electric vehicles such as trucks. Taking into consideration the imposed restrictions, one presents, in a comparative manner, the main geometrical parameters which come of the classical design algorithms. A special attention is dedicated to the winding design, since it has to ensure two synchronous speeds corresponding to 16 and 8 poles, respectively. Moreover, the influence of the rotor slots shape for the improvement of the start-up is analyzed. Finally, a FEM-based study (approach based on finite element method is performed to put in view specific torque and slip values such as rated, start-up and pull-out ones.

  12. Metal matrix composites: custom-made materials for automotive and aerospace engineering

    National Research Council Canada - National Science Library

    Kainer, K. U

    2005-01-01

    ... in traffic engineering, especially in automotive and transport technology. New applications are, for example, partially fiber-reinforced pistons and hybrid reinforced crank cases in passenger cars and truck engines, and particle-reinforced brake discs for light trucks, motorcycles, passenger cars and rail-mounted vehicles...

  13. Sensorless control of electromagnetic actuators for gas valves in spark ignition engines; Sensorlose Regelung elektromagnetischer Aktuatoren fuer die Betaetigung von Gaswechselventilen im Otto-Motor

    Energy Technology Data Exchange (ETDEWEB)

    Butzmann, S.

    2000-07-01

    A method for sensorless control of the impact speed of the armature of electromagnetic actuators is presented and described in great detail. The control algorithm was implemented in a compact electronic control unit for a 4-cylinder, 16-valve engine and was tested both in the laboratory and in a real engine. The method was first presented in September 1999 at the Frankfurt IHH, where it met with great interest. [German] In dieser Arbeit wurde ein Verfahren zur sensorlosen Regelung der Aufsetzgeschwindigkeit des Ankers bei elektromagnetischen Aktuatoren vorgestellt. Um den Anker zwischen den beiden Seiten des Luftspalts zu bewegen, werden zwei Elektromagnete abwechselnd bestromt, die Bewegung wird dabei von zwei Federn unterstuetzt. Fliesst waehrend eines solchen Umschwingvorgangs ein konstanter Strom durch die Spulen, so nimmt waehrend der Annaeherung an die Polflaeche die Magnetkraft mit der Luftspaltlaenge 1/l{sub L}{sup 2} zu, waehrend die entgegengesetzt wirkende Federkraft nur linear mit der Luftspaltlaenge l{sub L} steigt. Dies fuehrt prinzipiell zu einer unerwuenschten Beschleunigung des Ankers am Ende der Bewegung und damit zu einem harten Aufprall, der Laerm erzeugt und die Aktuatorlebensdauer reduziert. Ausgehend vom idealen Verfahren der zeitoptimalen Regelung, welches allerdings hohe Anforderungen an Sensorik und Rechenleistung stellt, wurde ein Algorithmus hergeleitet, welcher die zur Regelung der Aufsetzgeschwindigkeit erforderlichen Signale aus dem Stromverlauf in den Aktuatorspulen ableitet. Das neue Regelverfahren umgeht daher die Probleme, die durch den Einsatz von Sensoren entstehen. Waehrend der Ankerbewegung werden die Spulen zusaetzlich stimuliert, um eine hoehere Observationsgenauigkeit zu erzielen. Durch Adaption zwischen zwei aufeinanderfolgenden Ventilbetaetigungen und Regelung der Bewegung waehrend der Flugphase kann die Aufsetzgeschwindigkeit des Ankers praezise geregelt werden. Gleichzeitig konnte die zur Regelung erforderliche

  14. Performance of a cycle Otto engine using biogas; Desempenho de um motor ciclo Otto utilizando biogas como combustivel

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Juliano de [Universidade Estadual do Oeste do Parana (UNIOESTE), Cascavel, PR (Brazil). Centro de Ciencias Exatas e Tecnologicas], e-mail: jsouza@unioeste.br; Souza, Samuel N. Melegari de, [Universidade Estadual do Oeste do Parana (UNIOESTE), Cascavel, PR (Brazil); Machado, Paulo Romeu M [Universidade Federal de Santa Maria (UFSM), RS (Brazil). Dept. de Engenharia Mecanica

    2004-07-01

    The rising of the oil prices is increasing the search for alternative fuels. Brazil has a great availability of biogas from anaerobic digestion in the rural area, urban waste in the landfills and treatment of the municipal sewer. In this work were evaluated in dynamometer a cycle Otto engine using biogas, and were obtained the characteristics curves of torque and power. First was done the evidence test with gasoline, biogas and natural gas, using commercial systems for this fuels, using as comparison for other tests. After has been done tests for some combinations of ignition point, mixer of gas and compression tax. By the analysis of the results has been concluded that the better results for power and torque using biogas as fuel were with a tax compression of 12,5:1, gas mixer long and ignition point advanced in 45 deg. (author)

  15. Desempeño y emisiones de un motor de combustión interna con combustible dual Diesel – Gas natural ;Performance and emissions study of an internal combustion engine with dual fuel diesel - natural gas

    Directory of Open Access Journals (Sweden)

    Juan Miguel Mantilla González

    2015-04-01

    Full Text Available Muchos de los problemas reportados para los sistemas duales diesel- gas natural ocurren por mala dosificación del gas. Por esta razón se adaptó un sistema de alimentación dual con inyección electrónica de gas natural a un motor de combustión interna encendido por compresión. Se plantea un diseño experimental controlando el dosado de gas natural.Como resultado se obtiene un análisis comparativo entre los valoresde desempeño y emisiones desde la operación Diesel y Diesel-Gas natural. A partir de este análisis es posible observar que el desempeño del motor no se ve afectado por la operación del motor bajo el esquema Dual Diesel-GN, es decir que el motor funcionando bajo modo dual puede sostener las cargas solicitadas al motor. También se observa que la eficiencia volumétrica mejora bajo todas las condiciones de operación dual y las emisiones son mejores sólo cuando el motor trabaja a altas cargas. Many of the problems reported for dual diesel-natural gas systems occur due to poor gas dosage. For this reason a natural gas electronic injection feeding system was adapted to a compression ignitios internal combustion engine. An experimental design controlling the natural gas dosage is considered. As a result a comparative analysis between performance and emissions from the Diesel-and diesel-Natural Gas operation is obtained. From this analysis it is possible to see that engine performance is not affected by operation of the engine under the dual mode, i.e. the motor running under dual mode can support the loads applied to the engine. It is also observed that the volumetric efficiency improves under all conditions of operation and emissions from the dual mode of operation are better only when working at high engine loads.

  16. Truck Route Choice Modeling using Large Streams of GPS Data

    Science.gov (United States)

    2017-07-31

    The primary goal of this research was to use large streams of truck-GPS data to analyze travel routes (or paths) chosen by freight trucks to travel between different origin and destination (OD) location pairs in metropolitan regions of Florida. Two s...

  17. Waste Management's LNG Truck Fleet: Final Results

    Energy Technology Data Exchange (ETDEWEB)

    Chandler, K. [Battelle (US); Norton, P. [National Renewable Energy Laboratory (US); Clark, N. [West Virginia University (US)

    2001-01-25

    Waste Management, Inc., began operating a fleet of heavy-duty LNG refuse trucks at its Washington, Pennsylvania, facility. The objective of the project was to provide transportation professionals with quantitative, unbiased information on the cost, maintenance, operational, and emissions characteristics of LNG as one alternative to conventional diesel for heavy-duty trucking applications.

  18. Optimising Shovel-Truck Fuel Consumption using Stochastic ...

    African Journals Online (AJOL)

    Optimising the fuel consumption and truck waiting time can result in significant fuel savings. The paper demonstrates that stochastic simulation is an effective tool for optimising the utilisation of fossil-based fuels in mining and related industries. Keywords: Stochastic, Simulation Modelling, Mining, Optimisation, Shovel-Truck ...

  19. design and fabrication of a multipurpose railroad hand truck

    African Journals Online (AJOL)

    user

    the guide rail was constructed using 50mm by 50mm mild steel angle bar. The hand truck is ... material handling management, a company's operational performance may ... pose a health risk especially where the hand truck has to be used ...

  20. A Cognitive Analysis of Truck Drivers’ Right-hand Turns

    DEFF Research Database (Denmark)

    Sieker, Tobias Grønborg; G. Skulason, Thorgeir; Sletting, Kristian

    2015-01-01

    This paper presents an investigation of truck drivers’ performance during right-hand turns performed in intersections with traffic lights in order to elicit the truck drivers’ domain, decision-making processes, and the strategies used while executing the turn. To gain knowledge about this, a truc...

  1. 49 CFR 215.119 - Defective freight car truck.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defective freight car truck. 215.119 Section 215... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Freight Car Components Suspension System § 215.119 Defective freight car truck. A railroad may not place or continue in service a...

  2. Optimising Shovel-Truck Fuel Consumption using Stochastic ...

    African Journals Online (AJOL)

    Michael

    2017-12-02

    Dec 2, 2017 ... J. Bansah. 1University of Mines and Technology, P. O. Box 237, Tarkwa, Ghana. 2Missouri S&T .... of dump trucks which could be mixed fleets or same fleets. .... another portraying the reality of trucks moving from a shovel to a ...

  3. Activity Recognition and Localization on a Truck Parking Lot

    NARCIS (Netherlands)

    Andersson, M.; Patino, L.; Burghouts, G.J.; Flizikowski, A.; Evans, M.; Gustafsson, D.; Petersson, H.; Schutte, K.; Ferryman, J.

    2013-01-01

    In this paper we present a set of activity recognition and localization algorithms that together assemble a large amount of information about activities on a parking lot. The aim is to detect and recognize events that may pose a threat to truck drivers and trucks. The algorithms perform zone-based

  4. Reduction of power consumption in motor-driven applications by using PM motors; PM = Permanent Magnet; Reduktion af elforbrug til motordrift ved anvendelse af PM motorer

    Energy Technology Data Exchange (ETDEWEB)

    Hvenegaard, C.M.; Hansen, Mads P.R.; Groenborg Nikolaisen, C. (Teknologisk Institut, Taastrup (Denmark)); Nielsen, Sandie B. (Teknologisk Institut, AArhus (Denmark)); Ritchie, E.; Leban, K. (Aalborg Univ., Aalborg (Denmark))

    2009-12-15

    The traditional asynchronous motor with aluminum rotor is today by far the most widespread and sold electric motor, but a new and more energy efficient type of engine - the permanent magnet motor (PM motor) - is expected in the coming years to win larger and larger market shares. Several engine manufacturers in Europe, USA and Asia are now beginning to market the PM motors, which can replace the traditional asynchronous motor. The project aims to uncover the pros and cons of replacing asynchronous motors including EFF1 engines with PM motors, including the price difference. Furthermore, it is identified how the efficiency of PM motors is affected by low load levels and at various forms of control. Finally, the energy savings potential is analysed, by replacing asynchronous motors with PM motors. The study includes laboratory tests of PM motors, made in a test stand at Danish Technological Institute. (ln)

  5. 78 FR 28190 - Foreign-Trade Zone (FTZ) 134-Chattanooga, Tennessee; Notification of Proposed Production Activity...

    Science.gov (United States)

    2013-05-14

    ... to hydraulic excavators; bulldozers; wheel loaders; dump trucks; forklifts; forestry harvesters...; springs; supports; clamps; pipes; brackets; engines; engine blocks; engine plugs; engine cylinders; motors...

  6. Development of offroad unmanned dump truck navigation system. Dump truck mujin soko system no kaihatsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Horii, Z [Nittetsu Mining Co. Ltd., Tokyo (Japan)

    1992-08-25

    A large offroad unmanned dump truck navigation system has been developed, and is in practical operation mounted on dump trucks at Torigatayama Limestone Quarry of Nittetsu Mining Company. The system functions in a manual dump truck navigation mode, wireless navigation mode, and unmanned control mode. The unmanned control mode further includes a mode to navigate the truck on a predetermined course with its data having been input in a computer and a mode that when the truck was moved on a course under a wireless control, the computer learns the course and drives the truck autonomously thereafter. The safety measures are divided into the hardware safety function to detect abnormalities in brakes and other vehicle parts, and the software safety functions of data communications, sensor action check, and prevention of collision of trucks with each other. The system has resulted in a productivity of average one-way travel distance of 345 m, and average unmanned navigation cycle time of 9 minutes and 26 seconds for a transportation efficiency of 541 t/hour/truck, having reached at least the manned operation level. 4 figs., 1 tab.

  7. 75 FR 76518 - Volvo Trucks North America and Mack Trucks, Inc., Receipt of Petition for Decision of...

    Science.gov (United States)

    2010-12-08

    ... manufactured from March 1, 2007 through December 11, 2009. A total of 1,916 affected Volvo trucks were... trucks were manufactured from March 1, 2007, through December 11, 2009. A total 1,287 affected Mack... that their petition, to exempt them from providing recall notification of noncompliance as required by...

  8. Kvalitet budućih ulja za motore niskih emisija / Future lubricants quality for low emission engines

    Directory of Open Access Journals (Sweden)

    Radinko Gligorijević

    2004-01-01

    Full Text Available U tekućoj dekadi ovog milenijima proizvođači motora moraju postići dvostruko smanjenje potrošnje goriva, pa time i emisije CO2 i desetostruko smanjenje nivoa emisija, pre svega NOX i čestica. Za dostizanje tog cilja moraju se razviti nove specifikacije ulja, čiji doprinos smanjenju potrošnje goriva i nivou štetnih emisija postaje sve važniji. Trend razvoja ulja kreće se u pravcu nižih viskoznih gradacija sa nižim sadržajem sumpora, fosfora, sulfatnog pepela i nižom isparljivošću, čime se postiže smanjenje emisije, kao i potrošnje goriva. / In the current decade of this millennium automobile manufacturers must achieve an additional twofold increase in fuel efficiency and a tenfold reduction of emission of CO2 and pollutants, especially NOX and particles. To achieve this goal, a new specification of engine lubricants, whose contribution to fuel efficiency and reduction of emissions cannot be neglected, is to be developed. Development trends in lubricants move towards low viscosity, low content of sulfur, phosphorus, sulfate ash and low volatility, resulting in emission reduction and increase of fuel efficiency.

  9. Gas engine driven reversible heat pumps: Innovative design. Realizzazione di una pompa di calore reversibile azionata da motore a gas

    Energy Technology Data Exchange (ETDEWEB)

    Canci, F.; Zecchin, M.

    1992-01-01

    This paper describes the development of a series of gas engine driven air-water compression heat pumps designed for reversible summer-winter operation. The development work was carried out within the framework of a joint venture combing the efforts of the Italian Gas Society, Natural Gas of Barcellona and Climaveneta of Vicenza (Italy), who acted as the heat pump constructor. The main objective of this venture was to develop a series of machines that would be suitable for the contemporaneous summer air conditioning and winter space heating of medium-sized buildings. The designs were optimized to allow cost and energy savings with respect to conventional equipment. The useful cooling power range of the innovative heat pump systems goes from 100 to 250 kW thus giving them the flexibility not yet afforded by conventional equipment currently sold on international markets. In addition to pointing out the new heat pumps' main design and performance features, this paper suggests some feasible applications.

  10. Desempenho de motor diesel com misturas de biodiesel de óleo de girassol Performance of diesel engine fuelled with sunflower biodiesel blends

    Directory of Open Access Journals (Sweden)

    Ila Maria Corrêa

    2008-06-01

    Full Text Available Objetivou-se, neste trabalho avaliar o uso de misturas de biodiesel de girassol (Helianthus annuus L. e diesel no desempenho de um motor de ignição por compressão, injeção direta. Os ensaios foram realizados em bancada dinamométrica utilizando-se as misturas B5, B10, B20 e B100 em comparação ao diesel (D. Foi analisado o desempenho do motor através da tomada de potência (TDP com cada combustível, e analisado o óleo lubrificante do motor antes e após 96 horas de uso com B100. Os resultados obtidos foram: D (40,7 kW; 271 g/kW.h; B5 (40,3 kW; 271 g/kW.h; B10 (39,8 kW; 277 g/kW.h; B20 (40,0 kW; 277 g/kW.h e B100 (39,8 kW; 291 g/kW.h. Concluiu-se que o uso das misturas B5, B10, B20 e B100 proporcionou redução de no máximo 2,2 % na potência na TDP e um aumento máximo de 7,3 %, no consumo específico de combustível. A análise do óleo lubrificante, antes e após o uso com B100, detectou alterações aceitáveis, sendo a viscosidade, a presença de água e o teor de ferro os parâmetros mais expressivamente alterados.This work aimed to evaluate the use of sunflower biodiesel (Helianthus annuus L. blends in a CI engine, direct injection. The test procedure was carried out in a dynamometer bench that determined the performance of engine through power take-off (PTO with use of diesel and sunflower biodiesel blends (B5, B10, B20 and B100. The lubricating oil was analyzed before and after period of 96 hours. The results were: D (40,7 kW; 271 g/kW.h; B5 (40,3 kW; 271 g/kW.h; B10 (39,8 kW; 277 g/kW.h; B20 (40,0 kW; 277 g/kW.h e B100 (39,8 kW; 291 g/kW.h. One conclude that the use of blends B5, B10, B20 and B100 decreased the power of PTO max. 2,2% and increased the fuel consumption max. 7, 3%. The analysis of the lubricating oil before and after the use of B100 showed acceptable alterations and the viscosity, water content and level of iron were the most affected parameters.

  11. Intervention strategies to eliminate truck-related fatalities in surface coal mining in West Virginia.

    Science.gov (United States)

    Zhang, Meng; Kecojevic, Vladislav

    2016-01-01

    The main objective of this review was to build upon a previous study on the root causes of truck-related fatalities in surface coal mining operations in West Virginia, and to develop intervention strategies to eliminate these fatalities. This review considers a two-pronged approach to accident prevention: one that is fundamental and traditional (safety regulations, training and education, and engineering of the work environment); and one that is innovative and creative (e.g., applying technological advances to better control and eliminate the root causes of accidents). Suggestions for improving current training and education system are proposed, and recommendations are provided on improving the safety of mine working conditions, specifically safety conditions on haul roads, dump sites, and loading areas. We also discuss various currently available technologies that can help prevent haul truck-related fatal accidents. The results of this review should be used by mine personnel to help create safer working conditions and decrease truck-related fatalities in surface coal mining.

  12. Evaluation of an exhaust gas evacuation system during propane-fueled lift truck maintenance

    International Nuclear Information System (INIS)

    Roberge, B.; Beaudet, Y.; Lazure, L.; Menard, L.; Turcotte, A.

    2006-01-01

    Exposure to carbon monoxide (CO) gas in the workplace can cause health problem. CO gas is colourless and odourless, and exposure to it can cause intoxication, particularly for mechanics working on internal combustion engines fed by propane-fueled lift trucks. Regular procedures for evacuating the gases emitted during routine mechanical repairs involve the use of rigid evacuating pipes attached to the building and hooked to a flexible pipe at the end of the exhaust pipe. With lift trucks, this procedure is limited because of the configuration of these vehicles, and also because this type of work is often done in places without access to permanent mechanical ventilation. The object of this study was to propose a new evacuation method for CO gas fumes that would lower the exposures of fumes for mechanics and for workstations. It identified the criteria that should be considered, such as the configuration of the existing exhaust system of lift trucks, and feasibility of using this system at a variety of on-site locations. The design of the device was described and evaluated. 7 refs., 6 tabs., 8 figs., 3 appendices

  13. Engineering Ralstonia eutropha for Production of Isobutanol (IBT) Motor Fuel from Carbon Dioxide, Hydrogen, and Oxygen Project Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Sinskey, Anthony J. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Worden, Robert Mark [Michigan State Univ., East Lansing, MI (United States); Brigham, Christopher [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Lu, Jingnan [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Quimby, John Westlake [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Gai, Claudia [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Speth, Daan [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Elliott, Sean [Boston Univ., MA (United States); Fei, John Qiang [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Bernardi, Amanda [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Li, Sophia [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Grunwald, Stephan [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Grousseau, Estelle [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Maiti, Soumen [Michigan State Univ., East Lansing, MI (United States); Liu, Chole [Michigan State Univ., East Lansing, MI (United States)

    2013-12-16

    This research project is a collaboration between the Sinskey laboratory at MIT and the Worden laboratory at Michigan State University. The goal of the project is to produce Isobutanol (IBT), a branched-chain alcohol that can serve as a drop-in transportation fuel, through the engineered microbial biosynthesis of Carbon Dioxide, Hydrogen, and Oxygen using a novel bioreactor. This final technical report presents the findings of both the biological engineering work at MIT that extended the native branched-chain amino acid pathway of the wild type Ralstonia eutropha H16 to perform this biosynthesis, as well as the unique design, modeling, and construction of a bioreactor for incompatible gasses at Michigan State that enabled the operational testing of the complete system. This 105 page technical report summarizing the three years of research includes 72 figures and 11 tables of findings. Ralstonia eutropha (also known as Cupriavidus necator) is a Gram-negative, facultatively chemolithoautotrophic bacteria. It has been the principle organism used for the study of polyhydroxybutyrate (PHB) polymer biosynthesis. The wild-type Ralstonia eutropha H16 produces PHB as an intracellular carbon storage material while under nutrient stress in the presence of excess carbon. Under this stress, it can accumulate approximately 80 % of its cell dry weight (CDW) as this intracellular polymer. With the restoration of the required nutrients, the cells are then able to catabolize this polymer. If extracted from the cell, this PHB polymer can be processed into biodegradable and biocompatible plastics, however for this research, it is the efficient metabolic pathway channeling the captured carbon that is of interest. R. eutropha is further unique in that it contains two carbon-fixation Calvin–Benson–Bassham cycle operons, two oxygen-tolerant hydrogenases, and several formate dehydrogenases. It has also been much studied for its ability in the presence of oxygen, to fix carbon dioxide

  14. Traffic collisions between electric mobility devices (wheelchairs) and motor vehicles: Accidents, hubris, or self-destructive behavior?

    Science.gov (United States)

    LaBan, Myron M; Nabity, Thomas S

    2010-07-01

    This study had its genesis in a personally observed collision between a motor vehicle and a motorized wheelchair (electric mobility device) on a busy street in the middle of the block at an unmarked crossing. To the observer, at the time, this appeared to be a suicidal act. This investigation was initiated to both delineate the number of these crashes nationally and understand this phenomena as a potentially planned act of self-destruction. An initial survey of police reports was immediately frustrated by an inability to separate motor vehicle and electric mobility device collisions from the much larger group that involved ambulatory citizens because both types were classified together as "pedestrian" accidents. Instead, the search engine NexisLexis was used to identify 107 newspaper articles each of which described a motor vehicle and electric mobility device accident. In the motor vehicle and electric mobility device collisions, men predominated women (3:1 ratio) with an average age of 56 yrs. Sixty of these accidents were fatal. Ninety-four percent involved an electric mobility device and 6% a manual wheelchair. In 50% of the cases, the motor vehicle was a truck, van, or sport utility vehicle. Fifty percent occurred at dusk or dawn or at night. The electric mobility device occupant was cited as the guilty party in 39% of the cases and the driver of the motor vehicle in 27%. Twenty percent were unwitnessed hit-and-run accidents, whereas "no fault" was found in 8% of the cases. Although many accidents do happen by chance, when an electric mobility device operator openly challenges busy traffic by attempting to traverse it in the middle of the block at an unmarked crossing, predisposing psychosocial factors must also be considered. Hubris or premeditated self-destructive behavior or both need to be explored as preeminent issues with reference to the prodromal of the "accident process."

  15. Investigation of piston bowl geometry and speed effects in a motored HSDI diesel engine using a CFD against a quasi-dimensional model

    International Nuclear Information System (INIS)

    Rakopoulos, C.D.; Kosmadakis, G.M.; Pariotis, E.G.

    2010-01-01

    The present work investigates the effect of varying the combustion chamber geometry and engine rotational speed on the gas flow and temperature field, using a new quasi-dimensional engine simulation model in conjunction with an in-house developed computational fluid dynamics (CFD) code served to validate the predicted in-cylinder flow field and gas temperature distribution calculated by the quasi-dimensional model, for three alternative piston bowl geometries and three rotational speeds. This CFD code can simulate three-dimensional curvilinear domains using the finite volume method in a collocated grid; it solves the generalized transport equation for the conservation of mass, momentum and energy, and incorporates the standard k-ε turbulence model with some slight modifications to introduce the compressibility of a fluid in generalized coordinates. On the other hand, the quasi-dimensional model solves the general transport equation for the conservation of mass and energy by a finite volume method throughout the entire in-cylinder volume, while for the estimation of the flow field a new simplified three dimensional air motion model is used. To compare these two models the in-cylinder spatial and temporal temperature distribution, the mean cylinder pressure diagram, as well as the mean in-cylinder radial and axial velocity are examined, for the three piston bowl geometries and the three speeds, for a high speed direct injection (HSDI) diesel engine operating under motoring conditions. From the comparison of calculated results, it becomes apparent that the two models predict similar in-cylinder temperature distributions and mean air velocity fields at each crank angle, for all cases examined. Thus, it is shown that the quasi-dimensional model with the proposed simplified air motion model is capable of capturing the physical effect of combustion chamber geometry and speed on the in-cylinder velocity and temperature field, while needing significantly lower computing

  16. An alternative method for increasing the effectiveness of Diesel engine performance according to the altitude; Un metodo alternativo de elevacion de la efectividad del funcionamento de los motores diesel en condiciones de altura

    Energy Technology Data Exchange (ETDEWEB)

    Lastra Espinoza, Luis A. [Universidad Nacional de Ingenieria, Lima (Peru). Facultad de Ingenieria Mecanica; Patrakhaltsev, Nicolai N. [Universidad de la Amistad de los Pueblos, Moscou (Russian Federation). Catedra de Motores Combinados

    1995-07-01

    The development of new methods of the compensating of Diesel motor's losses due to the altitude are still in force, even through the supercharged turbocharging is the most effective method. It is possible to compensate the loss due to the altitude by forcing the work process through the fuel-air ratio. This forcing consists of intensifying the formation of the mixture and combustion process using activators in the engine cylinders. (author)

  17. Truck Drivers' Use of the Internet: A Mobile Health Lifeline.

    Science.gov (United States)

    Heaton, Karen; Combs, Bryan; Griffin, Russell

    2017-06-01

    Because of their social isolation, irregular and unpredictable schedules, limited access to health care, and long periods of travel, long-haul truckers may benefit from the use of mobile health applications on Internet-capable devices. The purpose of this study was to determine Internet access and usage among a sample of long-haul truck drivers. In this cross-sectional study, truck drivers completed a pencil and paper survey with questions on demographics, work and health histories, and Internet access and usage for both personal and job reasons. A total of 106 truck drivers were recruited from trucking industry trade shows, by word of mouth, and directly from trucking companies. Overall, the truck drivers' use of the Internet was limited. Their usage for personal and job-related reasons differed. Social connectivity and access to health and wellness information were important during personal usage time. Job-related Internet use was highly practical, and applied to seeking information for directions and maps, fuel stops and pricing, and communicating with employers or transmitting documents. Age and experience were associated with Internet use. Younger, less-experienced drivers used the Internet more than older, experienced drivers. Targeted mobile health messaging may be a useful tool to inform truck drivers of health conditions and plans, and may provide links to primary care providers needing to monitor or notify drivers of diagnostic results or treatment plans.

  18. Factors Affecting Accidents Risks among Truck Drivers In Egypt

    Directory of Open Access Journals (Sweden)

    Elshamly Ahmed Fathalla

    2017-01-01

    Full Text Available Egypt is ranked among the countries with the highest rates of road accidents. According to the American Chamber of Commerce more than 96% of Egypt's goods are transported by trucks and due to their large volume and excessive weight, the severity and number of truck accident fatalities are much higher than other vehicles in Egypt. The present study aims at identifying truck driver's behavior and its influence on crash involvement. Due to the shortage in recording accident data and the inaccurate road accident audit, data was collected from several governorates in Egypt through questionnaire. Questionnaire forms were filled out through personal interviews with truck drivers. The total number of respondents was 643. The final analysis was made on the 615 questionnaires with complete answers. The data was analyzed and logistic regression was applied to accident related data to examine the contributing factors affecting accident occurrence of truck drivers. Results showed that fatigue in terms of driving hours (continuous and total and lack of sleep, drug use during driving, and driver obesity are the most influencing factors on the occurrence of truck accidents in Egypt. The findings of this research highlight the important role human factors have on the risk of crash involvement amongst Egypt's truck drivers and the need to improve their work conditions.

  19. 76 FR 10396 - New United Motor Manufacturing, Inc., Formerly a Joint Venture of General Motors Corporation and...

    Science.gov (United States)

    2011-02-24

    ... Manufacturing, Inc., Formerly a Joint Venture of General Motors Corporation and Toyota Motor Corporation, Including On- Site Leased Workers From Corestaff, ABM Janitorial, Toyota Engineering and Manufacturing North... Motor Manufacturing, Inc., formerly a joint venture of General Motors Corporation and Toyota Motor...

  20. High efficiency motor selection handbook

    Science.gov (United States)

    McCoy, Gilbert A.; Litman, Todd; Douglass, John G.

    1990-10-01

    Substantial reductions in energy and operational costs can be achieved through the use of energy-efficient electric motors. A handbook was compiled to help industry identify opportunities for cost-effective application of these motors. It covers the economic and operational factors to be considered when motor purchase decisions are being made. Its audience includes plant managers, plant engineers, and others interested in energy management or preventative maintenance programs.

  1. Motor carrier evaluation program

    International Nuclear Information System (INIS)

    Portsmouth, James

    1992-01-01

    The U.S. Department of Energy-Headquarters (DOE-HQ), Transportation Management Program (TMP) has the overall responsibility to provide a well-managed transportation program for the safe, efficient, and economical transportation of DOE-owned materials. The DOE-TMP has established an excellent safety record in the transportation of hazardous materials including radioactive materials and radioactive wastes. This safety record can be maintained only through continued diligence and sustained effort on the part of the DOE-TMP, its field offices, and the contractors' organizations. Key elements in the DOE'S effective hazardous and radioactive materials shipping program are (1) integrity of packages, (2) strict adherence to regulations and procedures, (3) trained personnel, (4) complete management support, and (5) use of the best commercial carriers. The DOE Motor Carrier Evaluation Program was developed to better define the criteria and methodology needed to identify motor carriers for use in the transportation of Highway Route Controlled Quantities (HRCQ), Truck Load (TL) quantities of radioactive materials, hazardous materials and waste. (author)

  2. Corrosion Engineering.

    Science.gov (United States)

    White, Charles V.

    A description is provided for a Corrosion and Corrosion Control course offered in the Continuing Engineering Education Program at the General Motors Institute (GMI). GMI is a small cooperative engineering school of approximately 2,000 students who alternate between six-week periods of academic study and six weeks of related work experience in…

  3. CUSTOMER'S PERCEPTION TOWARDS FOOD TRUCK PRODUCTS IN INDIA

    OpenAIRE

    Dr. Ramakrishna Bandaru*, Prof. H. Venkateshwarlu

    2017-01-01

    Food Truck business is a very famous and a growing business in today’s time. Over the decade, every country in the world has been following the trend of the mobile food business. The silent feature of the food truck business is ‘customer reach and satisfaction’. Along with the increase in people living standards, ‘food on wheel’ business made a popular. According to IBIS World report, the food truck industry in the world has grown an average of 9.3% per year over the last five years. Slowly,...

  4. Projection of light-truck population to year 2025

    Energy Technology Data Exchange (ETDEWEB)

    1978-10-01

    The recent growth in the number of light trucks is a matter of considerable interest in that it may have far-reaching implications for gasoline consumption. This paper forecasts the number of light trucks in the years to 2025. The forecast is based on economic scenarios developed by SRI International. Except for the case of the most-dismal economic forecast, the number of light trucks is predicted to increase monotonically and to show the greatest rate of increase between 1973 and 1980.

  5. Evaluación del funcionamiento de motores de combustión interna trabajando con biodiesel. // Evaluation of engine performance working with biodiesel.

    OpenAIRE

    R. Piloto Rodríguez; R. Sierens; S. Verhelst; N. Ferrer Frontela

    2008-01-01

    En el presente trabajo se determinó la característica exterior de velocidad para dos motores de combustión internatrabajando con combustible biodiesel procedente de varias fuentes naturales y se comparó con la característica exterior develocidad de los motores originalmente trabajando con combustible diesel. Los motores fueron evaluados con variacionesde carga y velocidad. En uno de los motores ensayados fue determinada la presión en el interior de la cámara decombustión con el objetivo de ev...

  6. Amphibian Engineers in the Southwest Pacific

    Science.gov (United States)

    2017-03-08

    too dangerous. The 1st Engineer Amphibian Brigade was relegated to truck duty in England instead of preparing for the cross-channel invasion.21 Before...and dumps through the swamp.93 91 Office of the Chief Engineer , Amphibian Engineer ...inland, whereas the DUKW (and LVT) could drive direct from ship to dump site. 116 Office of the Chief Engineer , Amphibian Engineer Operations, 320-21

  7. Light trucks and highway fatalities : the role of network effects.

    Science.gov (United States)

    2012-12-01

    Light trucks, such as sport utility vehicles (SUVs) : and pickups, impose greater risks of injury and : death on other motorists than do cars, while at the : same time providing their occupants with increased : protection against these risks relative...

  8. Commercial truck platooning demonstration in Texas – level 2 automation.

    Science.gov (United States)

    2017-08-01

    Through this project, the Texas Department of Transportation (TxDOT) funded the creation of a comprehensive truck platooning demonstration in Texas, serving as a proactive effort in assessing innovative operational strategies to position TxDOT as a l...

  9. Market capitalization of the trucking industry sector, 2005

    Science.gov (United States)

    2006-08-01

    This report focuses on the market valuation of the overall trucking industry sector and each segment within it. In the past, while the focus has been on stock price appreciation or depreciation, this report emphasizes market capitalization returns. S...

  10. Building the Vocational Phase of the Computerized Motor Skills Testing System for Use in the Electronics and Electrical Engineering Group and Hospitality Group

    Science.gov (United States)

    Hsiao, Hsien-Sheng; Chen, Jyun-Chen; Hong, Kunde

    2016-01-01

    Technical and vocational education emphasizes the development and training of hand motor skills. However, some problems exist in the current career and aptitude tests in that they do not truly measure the hand motor skills. This study used the Nintendo Wii Remote Controller as the testing device in developing a set of computerized testing tools to…

  11. Crash risk factors for interstate large trucks in North Carolina.

    Science.gov (United States)

    Teoh, Eric R; Carter, Daniel L; Smith, Sarah; McCartt, Anne T

    2017-09-01

    Provide an updated examination of risk factors for large truck involvements in crashes resulting in injury or death. A matched case-control study was conducted in North Carolina of large trucks operated by interstate carriers. Cases were defined as trucks involved in crashes resulting in fatal or non-fatal injury, and one control truck was matched on the basis of location, weekday, time of day, and truck type. The matched-pair odds ratio provided an estimate of the effect of various driver, vehicle, or carrier factors. Out-of-service (OOS) brake violations tripled the risk of crashing; any OOS vehicle defect increased crash risk by 362%. Higher historical crash rates (fatal, injury, or all crashes) of the carrier were associated with increased risk of crashing. Operating on a short-haul exemption increased crash risk by 383%. Antilock braking systems reduced crash risk by 65%. All of these results were statistically significant at the 95% confidence level. Other safety technologies also showed estimated benefits, although not statistically significant. With the exception of the finding that short-haul exemption is associated with increased crash risk, results largely bolster what is currently known about large truck crash risk and reinforce current enforcement practices. Results also suggest vehicle safety technologies can be important in lowering crash risk. This means that as safety technology continues to penetrate the fleet, whether from voluntary usage or government mandates, reductions in large truck crashes may be achieved. Practical application: Results imply that increased enforcement and use of crash avoidance technologies can improve the large truck crash problem. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

  12. The Aggregate Planning For Trucking Operation in Cikarang Dry Port

    Directory of Open Access Journals (Sweden)

    Dwi Puspita Sari Utami

    2015-06-01

    Full Text Available Abstract. Cikarang Dry Port currently is the only dry port in Indonesia. This Dry Port has a role to connect or extend the Sea Port to the industrial areas located far from Sea Port. Thus, it creates a value added and also reduce costs. One of the operations done in Cikarang Dry Port is trucking operation. This research aims to examine the planning of 2014 trucking activity in Cikarang Dry Port to determine the right number of the truck that will be best occupied to manage all demands. The analysis begins with demand forecasting by using a moving average method of 12 months or one year period in 2013 which will be used as main information to develop the plans. There are three plans developed in this research. Based on the three plans, Plan A with minimum trucking plan with subcontracting is the most profitable which gives the highest profitability of Rp. 374,984,625. Recommendation for this research is using the current minimum number of 39 trucks rent with additional subcontracting when the demand is exceeding the capacity, thus, Cikarang Dry Port can occupy all demands and gain more profits. Keywords: Aggregate Planning; Scheduling; Trucking Operation; Moving Average; Cikarang Dry Port

  13. The Aggregate Planning For Trucking Operation in Cikarang Dry Port

    Directory of Open Access Journals (Sweden)

    Dwi Puspita Sari Utami

    2015-07-01

    Full Text Available Abstract. Cikarang Dry Port currently is the only dry port in Indonesia. This Dry Port has a role to connect or extend the Sea Port to the industrial areas located far from Sea Port. Thus, it creates a value added and also reduce costs. One of the operations done in Cikarang Dry Port is trucking operation. This research aims to examine the planning of 2014 trucking activity in Cikarang Dry Port to determine the right number of the truck that will be best occupied to manage all demands. The analysis begins with demand forecasting by using a moving average method of 12 months or one year period in 2013 which will be used as main information to develop the plans. There are three plans developed in this research. Based on the three plans, Plan A with minimum trucking plan with subcontracting is the most profitable which gives the highest profitability of Rp. 374,984,625. Recommendation for this research is using the current minimum number of 39 trucks rent with additional subcontracting when the demand is exceeding the capacity, thus, Cikarang Dry Port can occupy all demands and gain more profits.Keywords: Aggregate Planning; Scheduling; Trucking Operation; Moving Average; Cikarang Dry Port

  14. Application of Chaos Theory in Trucks' Overloading Enforcement

    Directory of Open Access Journals (Sweden)

    Abbas Mahmoudabadi

    2013-01-01

    Full Text Available Trucks' overloading is considered as one of the most substantial concerns in road transport due to a possible road surface damage, as well as, are less reliable performance of trucks' braking system. Sufficient human resource and adequate time scheduling are to be planned for surveying trucks' overloading; hence, it seems required to prepare an all-around model to be able to predict the number of overloaded vehicles. In the present research work, the concept of chaos theory has been utilized to predict the ratio of trucks which might be guessed overloaded. The largest Lyapunov exponent is utilized to determine the presence of chaos using experimental data and concluded that the ratio of overloaded trucks reflects chaotic behavior. The prediction based on chaos theory is compared with the results of simple smoothing and moving average methods according to the well-known criterion of mean square errors. The results have also revealed that the chaotic prediction model would act more capably comparing the analogous methods including simple smoothing and moving average to predict the ratio of passing trucks to be possibly overloaded.

  15. MCDA APPLIED TO PERFORMANCE APPRAISAL OF SHORT-HAUL TRUCK DRIVERS: A CASE STUDY IN A PORTUGUESE TRUCKING COMPANY

    Directory of Open Access Journals (Sweden)

    Raquel Morte

    2015-03-01

    Full Text Available Performance appraisal increasingly assumes a more important role in any organizational environment. In the trucking industry, drivers are the company's image and for this reason it is important to develop and increase their performance and commitment to the company's goals. This paper aims to create a performance appraisal model for trucking drivers, based on a multi-criteria decision aid methodology. The PROMETHEE and MMASSI methodologies were adapted using the criteria used for performance appraisal by the trucking company studied. The appraisal involved all the truck drivers, their supervisors and the company's Managing Director. The final output is a ranking of the drivers, based on their performance, for each one of the scenarios used. The results are to be used as a decision-making tool to allocate drivers to the domestic haul service.

  16. Motor of the future - superconducting

    International Nuclear Information System (INIS)

    Moen, Odd

    2001-01-01

    High-temperature superconductors count as the most innovative and future-oriented technology for electric motors. When these materials are used, the engine rating can be doubled and at the same time the losses halved while retaining the same size of construction. Siemens have recently developed a synchronous motor based on a high-temperature superconducting excitation winding. The rated power of the motor is 380 kW. The high-temperature superconductor that is used in this motor requires considerably less cooling outfit than low-temperature superconductors

  17. Performance evaluation of small scale internal combustion engine with mixtures for diesel oil-palm oil; Avaliacao do desempenho do motor de combustao interna de pequeno porte com misturas oleo diesel - oleo de dende

    Energy Technology Data Exchange (ETDEWEB)

    Seye, Omar; Souza, Rubem Cesar Rodrigues [Universidade Federal do Amazonas (CDEAM/UFAM), Manaus, AM (Brazil). Centro de Desenvolvimento Energetico Amazonico], Emails: Seye62omar@yahoo.com, rcsouza@internext.com.br

    2006-07-01

    This work aims at the performance evaluation of the Cummins 4B -3.9, an internal combustion engine of maximum power 75 hp (56.6 kW) for small scale power generation, burning different mixtures of diesel fuel and palm oil. The palm oil in nature is mixed manually, what unfortunately will influence the engine performance as it hinders the combustion. The test protocol will include the biodiesel, later on. The emissions were assessed for several proportions of mixture diesel/palm oil covering the strip from 0 to 20% and the results were compared to the engine performance when it operates with diesel only. The motor is coupled to a dynamometer, whose operation consists of the acceleration and deceleration of water in order to simulate the effect of a load being applied to the motor. The system is controlled by the software LT commander that allows the start up and the shutdown of the engine from the screen of the computer that also monitors the following parameters as speed of rotation of the motor (RPM), applied torque (N-m), potency (hp), temperature of the lubricating oil, temperature of the water in the entrance and exit of the motor, and temperature of the environment (deg C), pressures of the lubricating oil and of opening of the injector (mBar). While a flow meter coupled to the piping measures the consumption of fuel, the gas analyzer ECHO Line 6000 it monitors the concentration and temperature of carbon monoxide (CO) (ppm), nitric oxide (NO) (ppm), nitrogen dioxide (NO{sub 2}), (ppm), sulfur dioxide (SO{sub 2}) (ppm) and Oxygen (O{sub 2}) (%) in the exhaust gases. This equipment also determines the combustion parameters as excess of air and the efficiency. The technical results present the efficiency variation, the pressure of the fuel, monoxide carbon, NOx emissions, Oxygen content in the exhaust gases, for the different mixture proportions. Furthermore, the results of economic viability show generation cost values of US$ 135,66/MWh for the motor operating

  18. Adaptation of topology optimization on truck-structure; Kinshitsukaho ni yoru iso saitekika shuho no truck kozo eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Tachibana, H; Kojima, A; Chiba, S [Mitsubishi Motors Corp., Tokyo (Japan)

    1997-10-01

    An optimization using the homogenization method has been applied to a truck-structure on the concept design stage. A truck-structure is grouped into 3 classes (thin plate structure , thick plate structure and solid structure), then example, effectiveness and method for the application for the purpose of weight reduction , high rigidity and high eigen-frequency are introduced. 3 refs., 24 figs., 1 tab.

  19. Utilización de la zeolita para disminuir los gases tóxicos de los motores de combustión interna. // The utilization of Cuban zeolites in the decrease of toxic gases emissions of internal combustion engines.

    Directory of Open Access Journals (Sweden)

    J. L. Reyes González

    2003-01-01

    Full Text Available En el trabajo se presentan los resultados obtenidos al utilizar la zeolita natural cubana para la disminución de los gasestóxicos que los motores de combustión interna MCI. envían a la atmósfera. Los experimentos fueron realizados en bancosde pruebas de MCI. tanto para motores de carburación como para motores diesel. Obteniéndose eficiencias de disminucióndel CO del 80 %, del CnHm del 50% y el humo negro en un 90%. Se demuestra la importancia de la granulometría de lazeolita para esta eliminación y para mantener la potencia del motor dentro de rangos aceptables.Palabras claves: Toxicidad, zeolita, medio ambiente, filtros, gases de escape._______________________________________________________________________________Abstract.In this paper are presented the results of the utilization of Cuban zeolites in the decrease of toxic gas emissions toatmosphere of internal combustion engines, (MCI. The experiments were carried out in test bank for gasoline and dieselengines. The efficiency in the decrement of CO was of 80%, CnHm in 50%, and 90 % in soot. The size of the zeolitesparticle importance in the efficiency is demonstrated.Key words: Toxicity, zeolite, enviroment, filters, gas emissions.

  20. Liquefied Natural Gas for Trucks and Buses

    International Nuclear Information System (INIS)

    James Wegrzyn; Michael Gurevich

    2000-01-01

    Liquefied natural gas (LNG) is being developed as a heavy vehicle fuel. The reason for developing LNG is to reduce our dependency on imported oil by eliminating technical and costs barriers associated with its usage. The U.S. Department of Energy (DOE) has a program, currently in its third year, to develop and advance cost-effective technologies for operating and refueling natural gas-fueled heavy vehicles (Class 7-8 trucks). The objectives of the DOE Natural Gas Vehicle Systems Program are to achieve market penetration by reducing vehicle conversion and fuel costs, to increase consumer acceptance by improving the reliability and efficiency, and to improve air quality by reducing tailpipe emissions. One way to reduce fuel costs is to develop new supplies of cheap natural gas. Significant progress is being made towards developing more energy-efficient, low-cost, small-scale natural gas liquefiers for exploiting alternative sources of natural gas such as from landfill and remote gas sites. In particular, the DOE program provides funds for research and development in the areas of; natural gas clean up, LNG production, advanced vehicle onboard storage tanks, improved fuel delivery systems and LNG market strategies. In general, the program seeks to integrate the individual components being developed into complete systems, and then demonstrate the technology to establish technical and economic feasibility. The paper also reviews the importance of cryogenics in designing LNG fuel delivery systems

  1. High Power Density Motors

    Science.gov (United States)

    Kascak, Daniel J.

    2004-01-01

    With the growing concerns of global warming, the need for pollution-free vehicles is ever increasing. Pollution-free flight is one of NASA's goals for the 21" Century. , One method of approaching that goal is hydrogen-fueled aircraft that use fuel cells or turbo- generators to develop electric power that can drive electric motors that turn the aircraft's propulsive fans or propellers. Hydrogen fuel would likely be carried as a liquid, stored in tanks at its boiling point of 20.5 K (-422.5 F). Conventional electric motors, however, are far too heavy (for a given horsepower) to use on aircraft. Fortunately the liquid hydrogen fuel can provide essentially free refrigeration that can be used to cool the windings of motors before the hydrogen is used for fuel. Either High Temperature Superconductors (HTS) or high purity metals such as copper or aluminum may be used in the motor windings. Superconductors have essentially zero electrical resistance to steady current. The electrical resistance of high purity aluminum or copper near liquid hydrogen temperature can be l/lOO* or less of the room temperature resistance. These conductors could provide higher motor efficiency than normal room-temperature motors achieve. But much more importantly, these conductors can carry ten to a hundred times more current than copper conductors do in normal motors operating at room temperature. This is a consequence of the low electrical resistance and of good heat transfer coefficients in boiling LH2. Thus the conductors can produce higher magnetic field strengths and consequently higher motor torque and power. Designs, analysis and actual cryogenic motor tests show that such cryogenic motors could produce three or more times as much power per unit weight as turbine engines can, whereas conventional motors produce only 1/5 as much power per weight as turbine engines. This summer work has been done with Litz wire to maximize the current density. The current is limited by the amount of heat it

  2. Health promotion in the trucking setting: Understanding Dutch truck drivers' road to healthy lifestyle changes.

    Science.gov (United States)

    Boeijinga, Anniek; Hoeken, Hans; Sanders, José

    2016-10-17

    The working environment, the nature of the work, and the characteristics of truck drivers as a social group typically pose great challenges for the truck drivers' health and health promotion activities aiming to improve it. The purpose was to obtain a better understanding of (a) Dutch truck drivers' perceptions of health and lifestyle themes, and (b) the challenges they experience in their pursuit of a more healthy lifestyle, as a guiding framework for the development of health interventions targeting this occupational group. In this qualitative study, we conducted and analyzed 20 semi-structured interviews and seven cases of participant observations with Dutch truck drivers. Grounded theory was used to analyze the data. Our findings illustrate that Dutch truck drivers wish to improve their lifestyle but have unproductive associations with concepts of healthy living as well as a tendency to downplay their health risks. In addition, they experience barriers within their work and personal environment that prevent them from translating their intentions into actual lifestyle changes. Based on the insights derived from the interviews, we discuss recommendations for the development of more effective health promotion interventions for truck drivers.

  3. Air pollution from motor vehicle emissions

    International Nuclear Information System (INIS)

    Petrushevska, Ljubica

    1996-01-01

    This paper presents some aspects of air pollution from motor vehicle emissions as: characteristic primary and secondary pollutants, dependence of the motor vehicle emission from the engine type; the relationship of typical engine emission and performance to air-fuel ratio, transport of pollutants from mobile sources of emissions, as well as some world experiences in the control approaches for exhaust emissions. (author)

  4. Experimental thermodynamics of single molecular motor.

    Science.gov (United States)

    Toyabe, Shoichi; Muneyuki, Eiro

    2013-01-01

    Molecular motor is a nano-sized chemical engine that converts chemical free energy to mechanical motions. Hence, the energetics is as important as kinetics in order to understand its operation principle. We review experiments to evaluate the thermodynamic properties of a rotational F1-ATPase motor (F1-motor) at a single-molecule level. We show that the F1-motor achieves 100% thermo dynamic efficiency at the stalled state. Furthermore, the motor reduces the internal irreversible heat inside the motor to almost zero and achieves a highly-efficient free energy transduction close to 100% during rotations far from quasistatic process. We discuss the mechanism of how the F1-motor achieves such a high efficiency, which highlights the remarkable property of the nano-sized engine F1-motor.

  5. PROTOTIPE ALAT PENGEKSTRAK PATI SAGU TIPE MIXER ROTARY BLADE BERTENAGA MOTOR BAKAR Prototype of Mixer Rotary Blade of Sago Starch Extractor Powered by Internal Combustion Engine

    Directory of Open Access Journals (Sweden)

    Darma Darma

    2012-05-01

    Full Text Available Papua and West Papua Province have a large potential of sago. Approximately 994,000 hectares, mostly natural sago forest was existed in this area. Sago starch has long been an important source of nutrition troughout Papua. Product of sago palm is not only starch as source of carbohydrate for food stuff, but also for basic material of industries such as paper, plywood, hardboard, and food indutries. Traditional methods are used for starch extraction in almost all part of Papu, which is not efficient and production capacity is very low. The effort to increase sago starch production could be carry out by introducing mechanical equipment (traditional to mechanized processing. The objective of this research was to design mixer rotary blade of sago starch extraction powered by internal combustion engine. The result was prototype of mechanical sago starch extractor. The prototype has high performance with extraction capacity 160 kg of disintegrated pith per hour or equal to 33 kg of wet starch per hour, extractable starch more than 99 % while starch losses in hampas less lhan 1 %. Hopefully, application of this machine to the sago farmer will transform agricultural system from subsistence to commercial. It means that increasing of economic income. In conclusion, technically and economically this prototype was feasible. ABSTRAK Provinsi Papua dan Papua Barat memiliki potensi sagu yang sangat besar. Sekitar 994.000 hektar yang sebagian besar merupakan hutan sagu alam terdapat di kedua provinsi ini. Pati sagu telah lama digunakan sebagai sumber nutrisi bagi penduduk asli papua. Pati sagu tidak hanya digunakan sebagai sumber karbohidrat, namun juga digunakan seba- gai bahan dasar industri kertas, plywood, hardbord, dan pangan. Pengolahan sagu secara tradisional yang dilakukan oleh masyarakat tidak efisien dan kapasitas produksinya sangat rendah. Peningkatan produksi dapat dilakukan dengan mengintroduksi peralatan pengolahan mekanis untuk merubah metode

  6. Evaluación de un motor de encendido por chispa trabajando con mezclas etanol-gasolina; Evaluation of the spark-ignition engine fueled with ethanol–gasoline blends

    Directory of Open Access Journals (Sweden)

    Eliezer Ahmed Melo Espinosa

    2012-07-01

    Full Text Available En la presente investigación se realiza un análisis del rendimiento de un motor de encendido por chispa (Lada 1300 al usar como combustible mezclas de etanol con gasolina en un 10%, 20% y 30%. Los parámetros analizados en cada experimento fueron el torque efectivo, la potencia efectiva, el consumo específico de combustible y las emisiones de monóxido de carbono. Los resultados obtenidos se analizaron estadísticamente mediante una comparación de muestras múltiples en el software estadístico Statgraphics Centurion XV.II. Este análisis fue hecho con él con el objetivo de analizar las posibles diferencias entre los parámetros evaluados para cada combustible a una misma rpm. A partir de los resultados obtenidos se pudieron establecer satisfactoriamente dos porcientos adecuados de la mezcla etanol-gasolina para ser utilizado en motores de encendido por chispa (Lada en las condiciones de Cuba y sin hacer modificacionesen el motor. In this investigation an analysis based on the performances of an engine when using blends of anhydrous ethanol with regular gasoline as fuels is carried out. The experiments of the Lada 1300 engine were carriedout for different blends in 10%, 20% and 30% of ethanol in gasoline. The analyzed parameters for each experiment were the effective torque, the effective power, the specific fuel consumption and the carbon monoxide exhausts emissions. The obtained results were statistically analyzed through multiple-sample comparison in the software Statgraphics Centurion XV.II. This analysis was made with the objective of analyzing the possible differences among the evaluated parameters for each fuel to the same rpm. The appropriate percent of the anhydrous ethanol - regular gasoline blends for use in engine (Lada under the Cuba conditions and without making modifications were satisfactorily established.

  7. Experimental Tailer like Thermal Lag Engine to obtain pressure and volume diagrams//Motor de Lag Térmico experimental tipo Tailer para obtener diagramas de presión y volumen

    Directory of Open Access Journals (Sweden)

    Carlos Fernández-Aballí-Altamirano

    2012-12-01

    Full Text Available AbstractThe Thermal Lag Engine (TLE patented by Peter Tailer’s is briefly introduced. The discussion about the thermodynamic working principle of this external combustion machine is presented. For this work the claims in literature have been studied by the authors to design and develop an experimental installation with the objective of measuring for the first time the pressure-volume (pV relationship of a TLE asdescribed by Tailer and West. The pV diagrams are presented here and support previous theoretical claims about the TLE. Their triangular form shows the effects described by West in the expansion and compression processes caused by the variation of the cold heat transfer area. Also the relationshipbetween the heat transfer capacity of the engine and its working frequency becomes apparent from the measurements, indicating that larger heater areas and limited cold heat transfer characteristics allow more work production per cycle at higher operating frequencies.Key words: thermal lag engine, pressure-volume diagrams, external combustion engines._______________________________________________________________________________ResumenSe introduce brevemente el Motor de Lag Térmico (MLT patentado por Peter Tailer y se esboza el debate científico sobre la termodinámica de esta máquina de combustión externa. A partir del estudio de los distintos puntos de vista los autores de este trabajo desarrollaron una instalación experimental con elobjetivo de medir por primera vez la relación presión-volumen (pV de un MLT como el descrito por Tailer y West. Los diagramas pV son presentados y apoyan los planteamientos teóricos previos sobre los MLT.Su forma triangular muestra los efectos descritos por West sobre los procesos de compresión y expansión debido a la exposición variable del área fría de intercambio de calor. Las mediciones pV muestran la relación que existe entre la capacidad de intercambio de calor del motor y su frecuencia de

  8. Measuring Timber Truck Loads With Image Processing In Paper Mills

    Science.gov (United States)

    Silva, M. Santos; Carvalho, Fernando D.; Rodrigues, F. Carvalho; Goncalves, Ana N. R.

    1989-04-01

    The raw material for the paper industry is wood. To have an exact account of the stock of piled sawn tree trunks every truck load entering the plant's stockyard must be measured as to the amount of wood being brought in. Weighting down the trucks has its own problems, mainly, due to the high capacity of the tree trunks to absorb water. This problem is further enhanced when calculations must be made to arrive at the mass of sawn tree trunks which must go into the process of producing a certain quantity of paper pulp. The method presented here is based on two fixed cameras which take the image of the truck load. One takes a view of the trunks in order to get information on the average length of the tree trunks. The other obtains a side view which is digitised and by just discriminating against a grey level the area covered by the tree trunk cross section is measured. A simple arithmetic operation gives the volume of wood in the trunk. The same computer, a PC, will register the trucks particulars is almost independent of weather the wood is wet or dry and it serves trucks of any size.

  9. 40 CFR 85.1703 - Definition of motor vehicle.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Definition of motor vehicle. 85.1703... (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Exclusion and Exemption of Motor Vehicles and Motor Vehicle Engines § 85.1703 Definition of motor vehicle. (a) For the purpose of determining the...

  10. A seismic vertical vibrator driven by linear synchronous motors

    NARCIS (Netherlands)

    Noorlandt, R.P.; Drijkoningen, G.G.; Dams, J.; Jenneskens, R.

    2015-01-01

    A linear synchronous motor (LSM) is an electric motor that can produce large controllable forces and is therefore suitable as a driving engine for a seismic vibrator. This motor consists of two independent elements, a magnet track and a coil track, allowing practically unlimited motor displacements.

  11. The electric motor handbook

    Energy Technology Data Exchange (ETDEWEB)

    Hurst, R.W.; Feltham, P. (eds.)

    2004-05-01

    This handbook outlines the important role that electric motors play in modern society. It covers the field of motor applications from various motor types to their use and repair. It also presents practical applications of electric motors and methods on motor efficiency. More than half of all electricity generated, and 75 per cent of all industrial electricity consumption is consumed by electric motors. Electrical personnel must be aware of all factors involved in electric motors in order to choose and apply the appropriate size of electric motor. These factors include efficiency, sizing and proper application. The efficient use and maximum life expectancy of electric motors depends on proper motor protection, control and maintenance. This handbook includes articles from leading experts on electric motors in modern electrical systems. The content includes: design considerations; proper electric motor sizing techniques; optimal electric motor application; electric motor protection technology; electric motor control principles; electric motor maintenance and troubleshooting; induction electric motors; electric motor bearing currents; electric motor bearing lubrication; electromagnetism; electric motor enclosures; electric motor testing; electric motor repair; DC electric motor; electric motor starters; electric motor brushes; industrial electric motors; electric motor diagrams; AC electric motors; electric motor wiring; electric motor service; electric motor rewinding; electric motor winding; diagram of electric motor wiring; electric motor kit; and, troubleshooting electric motors. A directory of motor manufacturers and suppliers was also included. refs., tabs., figs.

  12. 75 FR 28656 - New United Motor Manufacturing, Inc., Formerly a Joint Venture of General Motors Corporation, and...

    Science.gov (United States)

    2010-05-21

    ... Manufacturing, Inc., Formerly a Joint Venture of General Motors Corporation, and Toyota Motor Corporation, Including On- Site Leased Workers From Corestaff, ABM Janitorial, and Toyota Engineering and Manufacturing... joint venture of General Motors Corporation and Toyota Motor Corporation, including on-site leased...

  13. 75 FR 62424 - New United Motor Manufacturing, Inc. Formerly a Joint Venture of General Motors Corporation and...

    Science.gov (United States)

    2010-10-08

    ... Manufacturing, Inc. Formerly a Joint Venture of General Motors Corporation and Toyota Motor Corporation Including On- Site Leased Workers From Corestaff, ABM Janitorial, Toyota Engineering and Manufacturing North... Manufacturing, Inc., formerly a joint venture of General Motors Corporation and Toyota Motor Corporation...

  14. 75 FR 47632 - New United Motor Manufacturing, Inc., Formerly a Joint Venture of General Motors Corporation and...

    Science.gov (United States)

    2010-08-06

    ... Manufacturing, Inc., Formerly a Joint Venture of General Motors Corporation and Toyota Motor Corporation, Including On- Site Leased Workers From Corestaff, ABM Janitorial, Toyota Engineering and Manufacturing North... of General Motors Corporation and Toyota Motor Corporation, including on-site leased workers from...

  15. Supplying of Assembly Lines Using Train of Trucks

    Science.gov (United States)

    Čujan, Zdeněk; Fedorko, Gabriel

    2016-11-01

    The typical supply system conceptions, i.e. the concepts "Just-in-time" (JIT) and "Just-in-sequence" (JIS) are very important factors with regard to a fluent operation of the assembly lines. Therefore the contemporary intra plant transport systems are being replaced by a new kind of the transportation technology, namely by means of the trains of trucks. The trains of trucks are used in two possible operational modes: either with a driver or without driver (fully automated). The trucks of the logistic trains are also cheaper and they are able to carry a larger volume and mass of the material at once. There are reduced in this way not only the investment costs, but also the operational expenses.

  16. General Motors natural gas vehicle initiatives

    International Nuclear Information System (INIS)

    Weber, J.; Koplow, M.D.

    1992-01-01

    General Motors (GM) has a number of natural gas vehicle (NGV) programs in progress that address various marketing, technical, and production planning issues that lean on the introduction of NGVs from GM. The initial target is light and medium duty trucks sold in non-attainment air quality regions. GM has also embarked on a longer term program that encompasses vehicle and systems development, gas supply and infrastructure development, and customer and market development. The major long-term issues are gas quality, supplier participation, and infrastructure

  17. Could Expanded Freight Rail Reduce Air Pollution from Trucks?

    Science.gov (United States)

    Bickford, E. E.; Holloway, T.; Johnston, M.

    2010-12-01

    Cars, trucks and trains are a significant source of emissions that impact both climate and air quality on regional to global scales. Diesel vehicles, most used for freight transport, account for 42% of on-road nitrogen oxide emissions, 58% of on-road fine particulate emissions, and 21% of on-road carbon dioxide emissions. With freight tonnage projected to increase 28% by 2018, and freight trucks the fastest growing source of transportation emissions, we evaluate the potential for increased rail capacity to reduce the environmental impacts of trucks. Most widely available mobile source emissions inventories contain insufficient spatial detail to quantify realistic emission scenario options, and none to date have been linked with commodity flow information in a manner appropriate to consider the true potential of rail substitution. To support a truck-to-rail analysis, and other policy assessments requiring roadway-by-roadway analysis, we have developed a freight emissions inventory for the Upper Midwest based on the Federal Highway Administration’s Freight Analysis Framework version 2.2 and the Environmental Protection Agency’s on-road emissions model, Mobile6.2. Using a Geographical Information System (GIS), we developed emissions scenarios for truck-to-rail modal shifts where 95% of freight tonnage on trips longer than 400 miles is shifted off of trucks and onto railways. Scenarios will be analyzed with the Community Multiscale Air Quality (CMAQ) regional model to assess air quality impacts of associated changes. By using well-respected transportation data and realistic assumptions, results from this study have the potential to inform decisions on transportation sustainability, carbon management, public health, and air quality.

  18. Roadmap and technical white papers for the 21st century truck partnership

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2006-12-01

    21st Century Truck Partnership will support the development and implementation of technologies that will cut fuel use and emissions and enhance safety, affordability, and performance of trucks and buses.

  19. Contributions of Diesel Truck Emissions to Indoor Elemental Carbon Concentrations in Home Proximate to Ambassador Bridge

    Science.gov (United States)

    Ambassador Bridge, connecting Detroit, Michigan and Windsor, Ontario, is the busiest international commercial vehicle crossing in North America, with a large percentage of heavy duty diesel trucks. This study seeks to examine the contribution of diesel truck traffic across Ambass...

  20. 27 CFR 24.229 - Tank car and tank truck requirements.

    Science.gov (United States)

    2010-04-01

    ... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Spirits § 24.229 Tank car and tank truck requirements. Railroad tank cars and tank trucks used to transport spirits for use in wine production will be constructed...

  1. Estimation and analysis of multifactor productivity in truck transportation : 1987 - 2003

    Science.gov (United States)

    2009-02-01

    The analysis has three objectives: 1) to estimate multifactor : productivity (MFP) in truck transportation during : 1987-2003; 2) to examine changes in multifactor productivity : in U.S. truck transportation, over time, and : to compare these changes...

  2. Managing truck arrivals with time windows to alleviate gate congestion at container terminals

    DEFF Research Database (Denmark)

    Chen, G.; Govindan, Kannan; Yang, Z.

    2013-01-01

    Long truck queues at gates often limit the efficiency of a container terminal and generate serious air pollution. To reduce the gate congestion, this paper proposes a method called'vessel dependent time windows (VDTWs)' to control truck arrivals, which involves partitioning truck entries into gro......Long truck queues at gates often limit the efficiency of a container terminal and generate serious air pollution. To reduce the gate congestion, this paper proposes a method called'vessel dependent time windows (VDTWs)' to control truck arrivals, which involves partitioning truck entries...... into groups and assigning different time windows to the groups. The proposed VDTWs method includes three steps: (1) predicting truck arrivals based on the time window assignment, (2) estimating the queue length of trucks, and (3) optimizing the arrangement of time windows to minimize the total cost...

  3. Factors affecting driver alertness during the operation of haul trucks in the South African mining industry

    CSIR Research Space (South Africa)

    Schutte, PC

    2003-06-01

    Full Text Available In view of the seriousness of haul trucks accidents, SIMRAC initiated research to identify factors affecting haul truck driver alertness during mining operations. The information obtained during the risk analysis was used to identify possible...

  4. 76 FR 59166 - Navistar Truck Development and Technology Center, a Subsidiary of Navistar International...

    Science.gov (United States)

    2011-09-23

    ... Development and Technology Center, a Subsidiary of Navistar International Corporation Truck Division, Fort... International Corporation, Truck Division, Fort Wayne, Indiana (subject firm). The negative determination was... is a headcount reduction across the nation, made possible by the Global Outsourcing. * * * '' The...

  5. Optimization of Front Axle Suspension System of Articulated Dump Truck

    DEFF Research Database (Denmark)

    Langer, Thomas Heegaard; Christensen, Brian B.; Mouritsen, Ole Ø.

    2010-01-01

    that has been subjected to comfort improvement is a two axle articulated dump truck. The comfort has been in terms of whole body vibration exposure and the overall improvement has been made possible by adding front axle suspension. However, a hydraulic stabilizing system between the tractor and trailer...... to evaluate the whole body vibrations. By use of a multibody simulation model of the dump truck the whole body vibration exposure has been computed using the predefined work cycle as model input. The design parameters comprise the components of the hydraulic subsystem of the suspension, i.e., the size...

  6. Customer expectations and current offers from food trucks in Helsinki

    OpenAIRE

    Nguyen, An

    2017-01-01

    The aim of this thesis is to determine whether there is a gap between what customers expect and what the food trucks in Helsinki offers in term of diversity of products, price, time and location of service. Do the current offers match with what customers would like to have? The food truck concept has a long history and since 2008 became an international phenomenon. However, it is still relatively young in Helsinki. There are concerted efforts from different parties included the city’s au...

  7. Disruption management for truck appointment system at a container terminal

    DEFF Research Database (Denmark)

    Li, N.; Chen, Gang; Jin, Z.

    2016-01-01

    -appointed arrivals at a container terminal that is running an appointment system. Second, we propose some response strategies to cope with different levels of disruptions, and evaluate their resilience ability with two Key Performance Indicators (KPIs): total waiting time of on-time trucks and total idling emissions...... of all trucks, in order to balance the service quality to punctual arrivals and green performance of the whole system. Third, we conduct a sensitivity analysis using a discrete event simulation to understand the performance of the proposed strategies. Considering both KPIs, the best strategy in most......-crane moving distance, especially when the first KPI is given lower weight than the second one....

  8. Impact of Platon ETC system on intercity trucking cost

    Directory of Open Access Journals (Sweden)

    Pogotovkina Natalya

    2017-01-01

    Full Text Available In 2015 Platon ETC System, a system of charging trucks with gross vehicle weight exceeding 12 tons, was implemented in Russia. The payment is collected as a compensation fo0 the damage caused to the federal public roads. Platon system is an additional source of financing for the road sector. However, its implementation made the carriers face the increasing costs. This paper presents the first results of the system functioning and the problems, associated with it. We consider the foreign systems of truck charging. The results of calculations, which show the effect of the toll collection on the prime cost of road freight transportation, are also presented.

  9. 75 FR 51521 - Federal Motor Vehicle Safety Standards; Air Brake Systems; Technical Report on the Effectiveness...

    Science.gov (United States)

    2010-08-20

    ....121) mandates antilock braking systems (ABS) on all new air-braked vehicles with a GVWR of 10,000...-0116] Federal Motor Vehicle Safety Standards; Air Brake Systems; Technical Report on the Effectiveness of Antilock Braking Systems in Heavy Truck Tractors and Trailers AGENCY: National Highway Traffic...

  10. 77 FR 53199 - California State Motor Vehicle Pollution Control Standards; Advanced Clean Car Program; Request...

    Science.gov (United States)

    2012-08-31

    ... cars, light-duty trucks and medium-duty passenger vehicles (and limited requirements related to heavy... ENVIRONMENTAL PROTECTION AGENCY [AMS-FRL-9724-4] California State Motor Vehicle Pollution Control Standards; Advanced Clean Car Program; Request for Waiver of Preemption; Opportunity for Public Hearing and...

  11. Exploring the Application of Information and Communication Technology in the U.S. Motor Carrier Industry

    Science.gov (United States)

    Haynes, Edward T.

    2010-01-01

    The problem addressed in this qualitative case study focused on the limited amount of scholarly research addressing the use of information and communication technology in U.S. motor carrier operations. The trucking industry is part of the service sector which contributes approximately 67.8 percent to the gross domestic product of the United…

  12. Real-time pedestrian detection in a Truck's blind spot camera

    OpenAIRE

    Van Beeck, Kristof; Goedemé, Toon

    2014-01-01

    In this paper we present a multi-pedestrian detection and tracking framework targeting a specific application: detecting vulnerable road users in a truck's blind spot zone. Research indicates that existing non-vision based safety solutions are not able to handle this problem completely. Therefore we aim to develop an active safety system which warns the truck driver if pedestrians are present in the truck's blind spot zone. Our system solely uses the vision input from the truck's blind spot c...

  13. Experiment and Simulation of Medium-Duty Tactical Truck for Fuel Economy Improvement

    Directory of Open Access Journals (Sweden)

    Allen M. Quail

    2011-02-01

    Full Text Available Fuel economy improvement on medium-duty tactical truck has and continues to be a significant initiative for the U.S. Army. The focus of this study is the investigation of Automated Manual Transmissions (AMT and mild hybridization powertrain that have potential to improve the fuel economy of the 2.5-ton cargo trucks. The current platform uses a seven-speed automatic transmission. This study utilized a combination of on-road experimental vehicle data and analytical vehicle modeling and simulation. This paper presents the results of (1 establishment of a validated, high fidelity baseline analytical vehicle model, (2 modeling and simulation of two AMTs and their control strategy, (3 optimization of transmissions shift schedules, and (4 modeling and simulation of engine idle stop/start and Belt-Integrated-Starter-Generator (B-ISG systems to improve the fuel economy. The fuel economy discrepancy between experimental average and the baseline simulation result was 2.87%. The simulation results indicated a 14.5% and 12.2% fuel economy improvement for the 10-speed and 12-speed AMT respectively. A stop/start system followed by a B-ISG mild hybrid system incorporating regenerative braking was estimated to improve fuel economy 3.39% and 10.2% respectively.

  14. Cummins Engine Company B5.9 Propane Engine Development, Certification, and Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    The ADEPT Group, Inc. (Los Angeles, California)

    1998-12-18

    The objective of this project was to successfuly develop and certify an LPG-dedicated medium-duty original equipment manufacturer (OEM) engine that could be put into production. The engine was launched into production in 1994, and more than 800 B5.9G engines are now in service in the United States and abroad. This engine is now offered by more than 30 bus and truck OEMs.

  15. Vector Control Using Series Iron Loss Model of Induction, Motors and Power Loss Minimization

    OpenAIRE

    Kheldoun Aissa; Khodja Djalal Eddine

    2009-01-01

    The iron loss is a source of detuning in vector controlled induction motor drives if the classical rotor vector controller is used for decoupling. In fact, the field orientation will not be satisfied and the output torque will not truck the reference torque mostly used by Loss Model Controllers (LMCs). In addition, this component of loss, among others, may be excessive if the vector controlled induction motor is driving light loads. In this paper, the series iron loss model ...

  16. KAJIAN TEKNIS PROPELLER -ENGINE MATCHING PADA KAPAL IKAN TRADISIONAL DENGAN MENGGUNAKAN MOTOR LISTRIK HYBRID DARI SOLAR CELL DAN GENSET SEBAGAI MESIN PENGGERAK UTAMA KAPAL DI KABUPATEN PASURUAN JAWA TIMUR

    Directory of Open Access Journals (Sweden)

    Eko Sasmito Hadi

    2012-03-01

    Full Text Available Ketersediaan energi tak terbarukan yang kian menipis akan menjadi permasalahan besar bagi kehidupan manusia, banyak pemikiran sudah dicurahkan oleh para ilmuan guna mengantisipasi adanya kemungkinan krisis energi di masa yang akan datang. Selain dari permasalahan keterbatasan energi yang ada juga timbul masalah baru dari penggunaan energi tak terbarukan tersebut yaitu berupa polusi dan pencemaran lingkungan yang berdampak pada perubahan iklim di dunia. Para pemimpin dari berbagai negara menggelar konferensi tentang perubahan iklim di Bali (UNFCCC, sebagai tindak lanjut dari Protokol Kyoto yang diselenggarakan di Jepang sebelumnya, sehubungan dengan perubahan iklim dunia, beberapa negara sepakat untuk mengurangi emisi gas buang pada mesin berbahan bakar mineral, yang dianggap sebagai penyumbang polusi udara terbanyak, dengan membuat kebijakan yang diharapkan dapat menjadi suatu solusi untuk mengurangi polusi udara, salah satu solusi yang dibahas penulis adalah penggunaan motor listrik sebagai pengganti mesin berbahan bakar mineral, tujuan dari penelitian ini adalah menghitung parameter pendukung propeller engine matching (putaran mesin, BHP mesin, dan hambatan kapal , pada kapal ikan tradisional KM Brandal, dan penentuan ukuran propeller yang sesuai dengan kapal ikan KM Brandal dengan menggunakan sistem hybrid. Dalam penelitian ini penulis melakukan pengukuran dan perhitungan pada sistem penggerak kapal baik di lapangan maupun simulasi hybrid, rangkaian hybrid ini terdiri dari beberapa komponen antara lain 2 buah solar cell 100 WP, genset 800 VA, 2 buah baterai 70 Ah, dan motor listrik 12 volt 80 ampere, sedangkan untuk mendapatkan tegangan listrik yang sama pada rangkaian hybrid beberapa komponen seperti baterai, genset, dan solar cell disusun secara paralel. Penelitian tentang Propeller-Engine Matching pada rangkaian hybrid kapal ikan KM Brandal menghasilkan beberapa parameter optimasi propeller antara lain hambatan kapal 1,04 kN, daya efektif

  17. Planning of Truck Platoons: a Literature Review and Directions for Future Research

    NARCIS (Netherlands)

    A. Kishore Bhoopalam (Anirudh); N.A.H. Agatz (Niels); R.A. Zuidwijk (Rob)

    2017-01-01

    textabstractA truck platoon is a set of virtually linked trucks that drive closely behind one another using automated driving technology. Benefits of truck platooning include cost savings, reduced emissions, and more efficient utilization of road capacity. To fully reap these benefits in the initial

  18. Effects of Variation in Truck Factor on Pavement Performance in Pakistan

    Directory of Open Access Journals (Sweden)

    Rabia Chaudry

    2013-01-01

    Full Text Available Seasonal variation coupled with heavy axle loading is the key factor in rapid road deterioration in Pakistan. The serviceability loss is further accelerated by the fact that truck drivers and owners consider overloading as a profitable practice unaware of the adverse effects of this practice. Weigh-in-motion data from two stations located between two major cities of Pakistan (Peshawar and Rawalpindi on Grand Trunk Road (N-5 were collected and analyzed. Analysis of variance and comparison of actual and designed truck factor were performed to identify the most damaging axle truck type. It was found that axle truck type 3 (single/tandem axle is most damaging among all truck types. The actual truck factor for axle truck type 3 is 6.4 times greater than design truck factor. Regression expressions of different forms were also investigated to determine the relationship between truck factor and gross vehicular weight for the specified truck types. An optimum generalization strategy was used to prevent over-generalization and ensure accuracy. For data analysis, 75% of data was used to develop regression models and remaining 25% was to validate those models. The results show that the polynomial expressions performed best and provide a robust relationship that can be employed by the highway authorities to estimate truck factor from gross vehicular weight with a high degree of confidence. It was also observed that damaging effect of various types of trucks was very severe and quite high.

  19. 75 FR 56651 - ITS Joint Program Office; Trucking Industry Mobility & Technology Coalition Annual Meeting

    Science.gov (United States)

    2010-09-16

    ... DEPARTMENT OF TRANSPORTATION ITS Joint Program Office; Trucking Industry Mobility & Technology... Transportation. ACTION: Notice. The Trucking Industry Mobility & Technology Coalition (TIMTC) Annual [[Page 56652...: Beating Gridlock with a Smart Grid; U.S. DOT Truck Technology Initiatives; and State and Federal...

  20. Scheduling Trucks in a Cross-Dock with Mixed Service Mode Dock Doors

    DEFF Research Database (Denmark)

    Bodnar, Peter; Azadeh, Kaveh; Koster, René de

    2017-01-01

    The problem considered in this paper is how to schedule inbound and outbound trucks subject to time windows at a multidoor cross-dock. Dock doors can either be dedicated to inbound or outbound trucks or be capable of handling both truck types. In addition, loads are allowed to be temporarily...

  1. 49 CFR 230.100 - Defects in tender truck axles and journals.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defects in tender truck axles and journals. 230... Steam Locomotives and Tenders Running Gear § 230.100 Defects in tender truck axles and journals. (a... wheel seats that is more than 1/8 of an inch in depth. (b) Tender truck journal condemning defects...

  2. Motor-operated gearbox efficiency

    Energy Technology Data Exchange (ETDEWEB)

    DeWall, K.G.; Watkins, J.C.; Bramwell, D. [Idaho National Engineering Lab., Idaho Falls, ID (United States); Weidenhamer, G.H.

    1996-12-01

    Researchers at the Idaho National Engineering Laboratory recently conducted tests investigating the operating efficiency of the power train (gearbox) in motor-operators typically used in nuclear power plants to power motor-operated valves. Actual efficiency ratios were determined from in-line measurements of electric motor torque (input to the operator gearbox) and valve stem torque (output from the gearbox) while the operators were subjected to gradually increasing loads until the electric motor stalled. The testing included parametric studies under reduced voltage and elevated temperature conditions. As part of the analysis of the results, the authors compared efficiency values determined from testing to the values published by the operator manufacturer and typically used by the industry in calculations for estimating motor-operator capabilities. The operators they tested under load ran at efficiencies lower than the running efficiency (typically 50%) published by the operator manufacturer.

  3. Motor-operated gearbox efficiency

    International Nuclear Information System (INIS)

    DeWall, K.G.; Watkins, J.C.; Bramwell, D.; Weidenhamer, G.H.

    1996-01-01

    Researchers at the Idaho National Engineering Laboratory recently conducted tests investigating the operating efficiency of the power train (gearbox) in motor-operators typically used in nuclear power plants to power motor-operated valves. Actual efficiency ratios were determined from in-line measurements of electric motor torque (input to the operator gearbox) and valve stem torque (output from the gearbox) while the operators were subjected to gradually increasing loads until the electric motor stalled. The testing included parametric studies under reduced voltage and elevated temperature conditions. As part of the analysis of the results, the authors compared efficiency values determined from testing to the values published by the operator manufacturer and typically used by the industry in calculations for estimating motor-operator capabilities. The operators they tested under load ran at efficiencies lower than the running efficiency (typically 50%) published by the operator manufacturer

  4. Motor-operator gearbox efficiency

    International Nuclear Information System (INIS)

    DeWall, K.G.; Watkins, J.C.; Bramwell, D.

    1996-01-01

    Researchers at the Idaho National Engineering Laboratory recently conducted tests investigating the operating efficiency of the power train (gearbox) in motor-operators typically used in nuclear power plants to power motor-operated valves. Actual efficiency ratios were determined from in-line measurements of electric motor torque (input to the operator gearbox) and valve stem torque (output from the gearbox) while the operators were subjected to gradually increasing loads until the electric motor stalled. The testing included parametric studies under reduced voltage and elevated temperature conditions. As part of the analysis of the results, we compared efficiency values determined from testing to the values published by the operator manufacturer and typically used by the industry in calculations for estimating motor-operator capabilities. The operators we tested under load ran at efficiencies lower than the running efficiency (typically 50%) published by the operator manufacturer

  5. Motor homopolar

    OpenAIRE

    Martín Muñoz, Agustín

    2007-01-01

    Mostramos la construcción de un modelo de motor homopolar, uno de los más antiguos tipos de motores eléctricos. Se caracterizan porque el campo magnético del imán mantiene siempre la misma polaridad (de ahí su nombre, del griego homos, igual), de modo que, cuando una corriente eléctrica atraviesa el campo magnético, aparece una fuerza que hace girar los elementos no fijados mecánicamente. En el sencillísimo motor homopolar colgado (Schlichting y Ucke 2004), el imán puede girar ...

  6. Influence of methane emissions and vehicle efficiency on the climate implications of heavy-duty natural gas trucks.

    Science.gov (United States)

    Camuzeaux, Jonathan R; Alvarez, Ramón A; Brooks, Susanne A; Browne, Joshua B; Sterner, Thomas

    2015-06-02

    While natural gas produces lower carbon dioxide emissions than diesel during combustion, if enough methane is emitted across the fuel cycle, then switching a heavy-duty truck fleet from diesel to natural gas can produce net climate damages (more radiative forcing) for decades. Using the Technology Warming Potential methodology, we assess the climate implications of a diesel to natural gas switch in heavy-duty trucks. We consider spark ignition (SI) and high-pressure direct injection (HPDI) natural gas engines and compressed and liquefied natural gas. Given uncertainty surrounding several key assumptions and the potential for technology to evolve, results are evaluated for a range of inputs for well-to-pump natural gas loss rates, vehicle efficiency, and pump-to-wheels (in-use) methane emissions. Using reference case assumptions reflecting currently available data, we find that converting heavy-duty truck fleets leads to damages to the climate for several decades: around 70-90 years for the SI cases, and 50 years for the more efficient HPDI. Our range of results indicates that these fuel switches have the potential to produce climate benefits on all time frames, but combinations of significant well-to-wheels methane emissions reductions and natural gas vehicle efficiency improvements would be required.

  7. Optimization analysis of propulsion motor control efficiency

    Directory of Open Access Journals (Sweden)

    CAI Qingnan

    2017-12-01

    Full Text Available [Objectives] This paper aims to strengthen the control effect of propulsion motors and decrease the energy used during actual control procedures.[Methods] Based on the traditional propulsion motor equivalence circuit, we increase the iron loss current component, introduce the definition of power matching ratio, calculate the highest efficiency of a motor at a given speed and discuss the flux corresponding to the power matching ratio with the highest efficiency. In the original motor vector efficiency optimization control module, an efficiency optimization control module is added so as to achieve motor efficiency optimization and energy conservation.[Results] MATLAB/Simulink simulation data shows that the efficiency optimization control method is suitable for most conditions. The operation efficiency of the improved motor model is significantly higher than that of the original motor model, and its dynamic performance is good.[Conclusions] Our motor efficiency optimization control method can be applied in engineering to achieve energy conservation.

  8. Design and Validation Testing of TruckScan to Assay Large Sacks of Fukushima Radioactive Debris on a Truck

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Atsuo [Canberra-Japan (Japan); Bronson, Frazier [Canberra Industries Inc. (United States)

    2015-07-01

    As a result of the March 2011 earthquake and resulting tsunami in Japan, there was a serious accident at the Fukushima Dai-ichi Nuclear Power Plant. This accident has contaminated soil and vegetation in a wide area around the plant. Decontamination projects over the last 4 years have resulted in large numbers of 1 cubic meter canvas bags of debris, commonly called Super Sacks [SS]. These are currently stored nearby where they were generated, but starting in 2015, they will be moved to various Interim Storage Facilities [ISF]. Trucks will typically carry 8-20 of these SSs. When the trucks arrive at the ISF they need to be rapidly sorted into groups according to radioactivity level, for efficient subsequent processing. Canberra Industries, Inc. [CI] has designed a new truck monitoring system 'TruckScan' for use at these ISFs. The TruckScan system must measure the entire truck loaded with multiple closely packed SSs, and generate a nuclide specific assay report showing the radioactivity in each individual SS. The Canberra-Japan office, along with Obayashi Corporation have performed validation testing to demonstrate to the regulatory authorities that the proposed technique was sufficiently accurate. These validation tests were conducted at a temporary storage area in Fukushima prefecture. Decontaminated waste of various representative types and of various levels of radioactivity was gathered and mixed to create homogeneous volumes. These volumes were sampled multiple times and assayed with laboratory HPGe detectors to determine the reference concentration of each pile. Multiple SSs were loaded from each pile. Some of the SSs were filled 50% full, others 75% full, and others 100% full, to represent the typical loading configuration of the existing SSs in the field. The content of the SSs are either sand, soil, or vegetation with densities ranging from 0.3 g/cc - 1.6 g/cc. These SSs with known concentrations of Cs-134 and Cs-137 were then loaded onto trucks in

  9. Design and Validation Testing of TruckScan to Assay Large Sacks of Fukushima Radioactive Debris on a Truck

    International Nuclear Information System (INIS)

    Suzuki, Atsuo; Bronson, Frazier

    2015-01-01

    As a result of the March 2011 earthquake and resulting tsunami in Japan, there was a serious accident at the Fukushima Dai-ichi Nuclear Power Plant. This accident has contaminated soil and vegetation in a wide area around the plant. Decontamination projects over the last 4 years have resulted in large numbers of 1 cubic meter canvas bags of debris, commonly called Super Sacks [SS]. These are currently stored nearby where they were generated, but starting in 2015, they will be moved to various Interim Storage Facilities [ISF]. Trucks will typically carry 8-20 of these SSs. When the trucks arrive at the ISF they need to be rapidly sorted into groups according to radioactivity level, for efficient subsequent processing. Canberra Industries, Inc. [CI] has designed a new truck monitoring system 'TruckScan' for use at these ISFs. The TruckScan system must measure the entire truck loaded with multiple closely packed SSs, and generate a nuclide specific assay report showing the radioactivity in each individual SS. The Canberra-Japan office, along with Obayashi Corporation have performed validation testing to demonstrate to the regulatory authorities that the proposed technique was sufficiently accurate. These validation tests were conducted at a temporary storage area in Fukushima prefecture. Decontaminated waste of various representative types and of various levels of radioactivity was gathered and mixed to create homogeneous volumes. These volumes were sampled multiple times and assayed with laboratory HPGe detectors to determine the reference concentration of each pile. Multiple SSs were loaded from each pile. Some of the SSs were filled 50% full, others 75% full, and others 100% full, to represent the typical loading configuration of the existing SSs in the field. The content of the SSs are either sand, soil, or vegetation with densities ranging from 0.3 g/cc - 1.6 g/cc. These SSs with known concentrations of Cs-134 and Cs-137 were then loaded onto trucks in

  10. Application of stepping motor

    International Nuclear Information System (INIS)

    1980-10-01

    This book is divided into three parts, which is about practical using of stepping motor. The first part has six chapters. The contents of the first part are about stepping motor, classification of stepping motor, basic theory og stepping motor, characteristic and basic words, types and characteristic of stepping motor in hybrid type and basic control of stepping motor. The second part deals with application of stepping motor with hardware of stepping motor control, stepping motor control by microcomputer and software of stepping motor control. The last part mentions choice of stepping motor system, examples of stepping motor, measurement of stepping motor and practical cases of application of stepping motor.

  11. Analysis of frame structure of medium and small truck crane

    Science.gov (United States)

    Cao, Fuyi; Li, Jinlong; Cui, Mengkai

    2018-03-01

    Truck crane is an important part of hoisting machinery. Frame, as the support component of the quality of truck crane, determines the safety of crane jib load and the rationality of structural design. In this paper, the truck crane frame is a box structure, the three-dimensional model is established in CATIA software, and imported into Hyperworks software for finite element analysis. On the base of doing constraints and loads for the finite element model of the frame, the finite element static analysis is carried out. And the static stress test verifies whether the finite element model and the frame structure design are reasonable; then the free modal analysis of the frame and the analysis of the first 8 - order modal vibration deformation are carried out. The analysis results show that the maximum stress value of the frame is greater than the yield limit value of the material, and the low-order modal value is close to the excitation frequency value, which needs to be improved to provide theoretical reference for the structural design of the truck crane frame.

  12. SVOC emissions from diesel trucks operating on biodiesel fuels

    Science.gov (United States)

    This study measured semivolatile organic compounds (SVOCs) in particle matter (PM) emitted from three heavy-duty trucks equipped with modern after-treatment technologies. Emissions testing was conducted as described by the George et al. VOC study also presented as part of this se...

  13. TITAN Legal Weight Truck cask preliminary design report

    International Nuclear Information System (INIS)

    1990-04-01

    The Preliminary Design of the TITAN Legal Weight Truck (LWT) Cask System and Ancillary Equipment is presented in this document. The scope of the document includes the LWT cask with fuel baskets; impact limiters, and lifting and tiedown features; the cask support system for transportation; intermodal transfer skid; personnel barrier; and cask lifting yoke assembly. 75 figs., 48 tabs

  14. Haulage Truck Operator. Open Pit Mining Job Training Series.

    Science.gov (United States)

    British Columbia Dept. of Education, Victoria.

    This training outline for haulage truck operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for…

  15. Model development for air conditioning system in heavy duty trucks

    NARCIS (Netherlands)

    Kessels, J.T.B.A.; van den Bosch, P.P.J.; Zhang, Quansheng; Li, Shengbo Eben; Deng, Kun

    2016-01-01

    This chapter presents a modelling approach for the air conditioning (AC) system in heavy duty trucks. The presented model entails two major elements: a mechanical compressor model and a thermal AC model. The compressor model describes the massflow of the refrigerant as well as the mechanical power

  16. Presenting a conceptual pattern of HSE performance of oil trucks.

    Science.gov (United States)

    Ghaleh, Sahar; Omidvari, Manouchehr; Nassiri, Parvin; Momeni, Mansour; Lavasani, Seyed Mohammadreza Miri

    2018-01-25

    Accidents are among the main problems in the oil product supply chain. The most important effective factors in these events are the kind of trucks used and their health, safety, and environment (HSE) condition. The aim of this study was to present a conceptual pattern of the HSE performance of oil trucks in oil industries. In this study, 20 truck models (with fixed tanks), in use over different periods of time, were investigated. In this regard, the criteria and sub-criteria were first determined in two parts-carrier and tank-and weighted by fuzzy analytical hierarchy process (FAHP). The results showed that the most important sub-criteria regarding the HSE factors of the carrier were resistance and strength of the front and rear shields, the brake system, and the ventilation system. The most important sub-criteria regarding the HSE factors of the tank were tank shell thickness and a good tank design shape with respect to portable material. It should be noted that the weight of the criteria with each other and sub-criteria with each other are not equal. This issue is important for decision-making. The main reason for the use of trucks with the lowest score in developing countries is the lack of attention by managers to safety issues and international standards and agreements such as the ADR.

  17. U10 : Trusted Truck(R) II (phase B).

    Science.gov (United States)

    2009-01-01

    Phase B of the Trusted Truck II project built on the system developed in Phase A (or Year 1). For the implementation portion of the project, systems were added to the trailer to provide additional diagnostic trailer data that can be sent to the TTM...

  18. 29 CFR 1910.180 - Crawler locomotive and truck cranes.

    Science.gov (United States)

    2010-07-01

    ... the shaft or spindle with which or about which a wheel rotates. On truck- and wheel-mounted cranes it... and ropes. Cranes designed for railway and automobile wreck clearances are excepted. The requirements..., 1971, shall meet the design specifications of the American National Standard Safety Code for Crawler...

  19. ISAF'S Afghan Truck Drivers: The Overlooked Counterinsurgency Population

    Directory of Open Access Journals (Sweden)

    Myron Varouhakis

    2015-12-01

    Full Text Available A yearlong U.S. Army field study in Afghanistan examined the demographics and threat perceptions of one of the most-at-risk populations, that of Afghan truck drivers working for NATO’s International Security Assistance Force Afghanistan (ISAF. The study collected data from 766 Afghan truck drivers at the U.S.-operated Kandahar Airfield in ISAF’s Regional Command South. The findings show a wide diversity in age of the Afghan drivers as well as in terms of their home province. The findings also show that although all Afghan truck drivers had acute awareness and understanding of the high risks and dangers of the job, they all noted that the attractive salary and scarcity of jobs were dominant reasons for staying on the job. Findings also reveal a strong resentment among the Afghan truck drivers about their treatment by ISAF soldiers, as for the lack of protection for them and their families after the 2014 departure of NATO forces. The findings can provide significant insights and enhance the understanding of scholars, counterinsurgency strategists, policymakers, and military planners about “Host Country Nationals” as an important population of the human terrain.

  20. Desempenho de motor diesel quatro tempos alimentado com biodiesel de óleo de soja (B 100 Performance of four stroke diesel cycle engine supplied with soybean oil biodiesel (B 100

    Directory of Open Access Journals (Sweden)

    Carlos Eduardo Silva Volpato

    2009-08-01

    Full Text Available Objetivou-se, neste trabalho, avaliar o desempenho de um motor de ciclo diesel quatro tempos e quatro cilindros utilizando biodiesel de óleo de soja (B100, em comparação ao óleo diesel. Foram analisados os parâmetros: potência efetiva e reduzida, torque, consumo específico e energético de combustível, eficiência termomecânica e volumétrica. Foi instalado um ensaio com delineamento inteiramente casualizado (DIC em esquema fatorial, realizada análise de variância e aplicado teste de Tukey, a 5%. Foram pesquisados cinco níveis de rotação em quatro repetições (650, 570, 490, 410, 320 e 240 rpm. O motor alimentado com biodiesel apresentou torque e potência reduzida um pouco menor que quando alimentado com óleo diesel fóssil, entretanto, os consumos especifico e horário, apresentaram resultados mais satisfatórios que o diesel fóssil.The aim of this work was to compare the performance of a four stroke diesel cycle engine and a four cylinder using biodiesel made from soy oil (B100, in comparison with the diesel oil. The parameters analyzed were: effective power and reduced power, torque, specific and energetic consumption of fuel, thermal-mechanics and volumetric efficiency. An entirely randomized experiment design was installed (DIC in a factorial structure, the analysis of variance was carried out and the Tukey test was applied at the level of 5%. Five rotation levels were researched in four replications (650, 570, 490, 410, 320, and 240 rpm. The engine fed with biodiesel presented torque and reduced power a little lower than the engine fed with fossil diesel. However, specific and hourly consumptions presented more satisfactory results.

  1. Motor-operated valve (MOV) actuator motor and gearbox testing

    International Nuclear Information System (INIS)

    DeWall, K.; Watkins, J.C.; Bramwell, D.

    1997-07-01

    Researchers at the Idaho National Engineering and Environmental Laboratory tested the performance of electric motors and actuator gearboxes typical of the equipment installed on motor-operated valves used in nuclear power plants. Using a test stand that simulates valve closure loads against flow and pressure, the authors tested five electric motors (four ac and one dc) and three gearboxes at conditions a motor might experience in a power plant, including such off-normal conditions as operation at high temperature and reduced voltage. They also monitored the efficiency of the actuator gearbox. All five motors operated at or above their rated starting torque during tests at normal voltages and temperatures. For all five motors, actual torque losses due to voltage degradation were greater than the losses calculated by methods typically used for predicting motor torque at degraded voltage conditions. For the dc motor the actual torque losses due to elevated operating temperatures were greater than the losses calculated by the typical predictive method. The actual efficiencies of the actuator gearboxes were generally lower than the running efficiencies published by the manufacturer and were generally nearer the published pull-out efficiencies. Operation of the gearbox at elevated temperature did not affect the operating efficiency

  2. Optimizing transient processes with AVL-GCA for a highly flexible gasoline engine; Optimierung transienter Vorgaenge mit AVL-GCA an einem Otto-Motor hoher Flexibilitaet

    Energy Technology Data Exchange (ETDEWEB)

    Leifert, Thomas; Moreno Nevado, Fernando; Fairbrother, Robert; Prevedel, Kurt [AVL List GmbH, Graz (Austria)

    2011-07-01

    Optimizing the dynamic operation of a gasoline engine with high flexibility by means of AVL-GCA. Downsizing and Downspeeding are considered being the most promising approaches to significantly reduce CO{sub 2} emission. Because of synergy effects between its technologies, downsized Turbocharged Gasoline Direct Injection (TGDI) engines have the highest potential for fuel economy. The key for high market penetration of such concepts requires customer acceptance and this is closely linked to driver satisfaction. For the drivability rating of vehicles fitted with turbocharged engines, tip-in behavior is of paramount importance. A combined combustion analysis and gas-exchange analysis was performed with AVL GCA (Gas exchange and Combustion Analysis) on a ''beyond-state-of-the-art'' TGDI engine, namely a variable compression ratio engine featuring MCE-5 VCRi technology. With variable compression ratio and 2-stage boosting this engine features an unusually high level of flexibility. Therefore the analysis is used to examine the thermodynamic processes taking place in the cylinders not only in steady state operation but also under highly transient boundary conditions and on a ''cycle-by-cycle'' basis in order to examine hints for optimizing transient response. An established numerical approach for analysis was applied to measurement data acquired on an engine dynamometer thanks to a dedicated measurement chain that will be described in detail. (orig.)

  3. Dynamics of dump truck entrance onto the hoist platform of a mine inclined elevator

    Energy Technology Data Exchange (ETDEWEB)

    Nosyrev, B.A.; Popov, Yu.V.; Mukhutdinov, Sh.D. (Sverdlovskii Gornyi Institut (USSR))

    1989-01-01

    Analyzes the feasibility of transporting heavy-duty dump trucks along slopes on special platforms in coal surface mines. The platforms are hoisted by winches. Theoretical problems associated with hoisting a loaded platform upwards are analyzed. Problems associated with truck travel in the platform area, its exact positioning and mechanical vibrations of the platform caused by truck movement are discussed. Vibrations of the platform with a loaded truck and vibration amplitudes are analyzed. Five states of the system are evaluated. Methods for prevention of excessive vibrations by optimization of platform design and use of flexible elements are evaluated. Optimum speed of truck movement for platform entering is recommended.

  4. Evaluating sustainability of truck weight regulations: A system dynamics view

    Directory of Open Access Journals (Sweden)

    Pei Liu

    2015-11-01

    Full Text Available Purpose: Targeting the problem of overload trucking in Highway Transportation of iron ore from Caofeidian to Tangshan (HTCT, this paper aims to assess long-term effects of alternative Truck Weight Regulation (TWR policies on sustainability of HTCT. Design/methodology/approach: A system dynamics model was established for policy evaluation. The model, composed of six interrelating modules, is able to simulate policies effects on trucking issues such as freight flow, truck traffic flow, pavement performance, highway transport capacity and trucking time, and further on the Cumulative Economic Cost (CEC including transport cost and time cost of freight owners and the Cumulative Social Cost (CSC including pavement maintenance cost, green house gas emission cost, air pollutants emission cost and traffic accidents cost, so the effects of TWR policies on sustainability of HTCT could be evaluated. Findings: According to different values of overload ratio which a TWR policy allows, alternative TWR policies are classified into three types, which are The Rigid Policy (TRP, The Moderate Policy (TMP and The Tolerant Policy (TTP. Results show that the best policy for sustainability of HTCT depends on the importance of CSC which is expected by the local government. To be specific, (1 if CSC is considered much less important than CEC, the local government should continue implementing the current TTP with the maximum overload ratio; (2 if CSC is considered much more important than CEC, then TRP is recommended; and (3 if CSC is considered slightly more important than CES, TMP with overload ratio of 80% is the best. Practical implications: Conclusions of this paper may help the local government design appropriate TWR policies to achieve sustainability of HTCT. Originality/value: To the best of our knowledge, this is the first effort to evaluate TWR policies on sustainability of regional freight transportation based on system dynamics modeling.

  5. Waste heat recovery for transport trucks using thermally regenerative fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Carrier, A.; Wechsler, D.; Whitney, R.; Jessop, P. [Queen' s Univ., Kingston, ON (Canada). Dept. of Chemistry; Davis, B.R. [Queen' s-RMC Fuel Cell Research Centre, Kingston, ON (Canada)

    2009-07-01

    Carbon emissions associated with transportation can be reduced by increasing the fuel efficiency of transport trucks. This can be achieved with thermally regenerative fuel cells that transform the waste heat from the engine block into electricity. In order to operate such a fuel cell, one needs a fluid which rapidly, reversibly, and selectively undergoes dehydrogenation. Potential fluids have been screened for their ability to dehydrogenate and then rehydrogenate at the appropriate temperatures. An examination of the thermodynamics, kinetics, and selectivities of these processes have shown that the challenge involving hydrogenolysis at high temperature must be addressed. This paper discussed the economics of thermally regenerative fuel cells and the advantages and disadvantages of the identified fluids, and of such systems in general.

  6. Implementation of an optimal control energy management strategy in a hybrid truck

    NARCIS (Netherlands)

    Mullem, D. van; Keulen, T. van; Kessels, J.T.B.A.; Jager, B. de; Steinbuch, M.

    2010-01-01

    Energy Management Strategies for hybrid powertrains control the power split, between the engine and electric motor, of a hybrid vehicle, with fuel consumption or emission minimization as objective. Optimal control theory can be applied to rewrite the optimization problem to an optimization

  7. A distributed optimization approach to energy management for a heavy-duty truck

    NARCIS (Netherlands)

    Romijn, Constantijn; Donkers, Tijs; Weiland, Siep; Kessels, John

    2014-01-01

    Energy management systems (EMS) aim at minimizing the vehicle fuel consumption and tailpipe emissions under the wide range of driving conditions. Classical energy management systems for hybrid vehicles control the powersplit between the internal combustion engine (ICE) and the electric motor (EM)

  8. Advanced vehicle dynamics of heavy trucks with the perspective of road safety

    Science.gov (United States)

    Trigell, Annika Stensson; Rothhämel, Malte; Pauwelussen, Joop; Kural, Karel

    2017-10-01

    This paper presents state-of-the art within advanced vehicle dynamics of heavy trucks with the perspective of road safety. The most common accidents with heavy trucks involved are truck against passenger cars. Safety critical situations are for example loss of control (such as rollover and lateral stability) and a majority of these occur during speed when cornering. Other critical situations are avoidance manoeuvre and road edge recovery. The dynamic behaviour of heavy trucks have significant differences compared to passenger cars and as a consequence, successful application of vehicle dynamic functions for enhanced safety of trucks might differ from the functions in passenger cars. Here, the differences between vehicle dynamics of heavy trucks and passenger cars are clarified. Advanced vehicle dynamics solutions with the perspective of road safety of trucks are presented, beginning with the topic vehicle stability, followed by the steering system, the braking system and driver assistance systems that differ in some way from that of passenger cars as well.

  9. 40 CFR 85.1715 - Aircraft meeting the definition of motor vehicle.

    Science.gov (United States)

    2010-07-01

    ... motor vehicle. 85.1715 Section 85.1715 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Motor Vehicles and Motor Vehicle Engines § 85.1715 Aircraft meeting the definition of motor vehicle. This section applies for aircraft meeting the definition of motor vehicle in § 85.1703. (a) For the...

  10. Ventajas del uso de la inyección electrónica para vehículos diesel pesados en las condiciones de Cuba. // Advantages of electronic injection for diesel engines in heavy duty equipment.

    Directory of Open Access Journals (Sweden)

    J. Luis Reyes González

    2002-09-01

    Full Text Available Tomando en cuenta la importancia que tiene para Cuba el obtener una eficiencia energética elevada en los motores decombustión interna, al igual que el control de las emanaciones de gases tóxicos en los mismos, se realizó este trabajo dondese demuestran las ventajas tanto en el orden económico como ecológico de los motores diesel con mando electrónico paraequipos pesados empleados en la transportación de carga por camiones en la empresa Cubalse.Por medio de métodos experimentales y estadísticos, se obtuvo el consumo de combustible y la humosidad en motores coninyección electrónica (Detroit y en motores que utilizan los métodos tradicionales (Cummins. Los rresultadosdemostraron la superioridad en ambos aspectos de los motores con inyección electrónica.Se realizó una valoración del tiempo de amortización de la inversión inicial necesaria para utilizar en el parque existenteesta novedosa técnica de la inyección electrónica.Palabras claves: Eficiencia energética, inyección electrónica, consumo de combustible, motores de combustióninterna.__________________________________________________________________Abstract.Taking into consideration the importance of achieving a high efficiency in the internal combustion engines and emissioncontrol of the exhaust gases, this paper deals with economical and environmental advantages of the electronic controlleddiesel engines in heavy-duty trucks, which are used by Cubalse in the transportation. The fuel consumption and the sootemission in Detroit motors (with electronic injection system and Cummins (with traditional system, were studied usingstatistic and experimental methods, and the Detroit proved to be superior in both parameters. The pay back time for theinvestment needed to change the systems of all the existent trucks were calculatedKey words: Energetic efficiency, electronic injection, fuel consumption, internal combustion engine.

  11. Performance of cycle diesel engine using Biodiesel of olive oil (B100 Desempenho de motor diesel quatro tempos alimentado com biodiesel de óleo de oliva (B100

    Directory of Open Access Journals (Sweden)

    Carlos Eduardo Silva Volpato

    2012-06-01

    Full Text Available Biodiesel is a renewable fuel derived from vegetable oils used in diesel engines, in any proportion with petroleum diesel, or pure. It is produced by chemical processes, usually by transesterification, in which the glycerin is removed. The objective of this study was to compare the performance of a four stroke, four cylinder diesel cycle engines using either olive (B100 biodiesel oil or diesel oil. The following parameters were analyzed: effective and reduced power, torque, specific and hourly fuel consumption, thermo-mechanical and volumetric efficiency. Analysis of variance was performed on a completely randomized design with treatments in factorial and the Tukey test applied at the level of 5%. Five rotation speeds were researched in four replications (650, 570, 490, 410, 320 and 240 rpm. The engine fed with biodiesel presented more satisfactory results for torque, reduced power and specific and hourly consumptions than that fed with fossil diesel.Biodiesel é um combustível renovável derivado de óleos vegetais, usado em motores de ciclo diesel, em qualquer proporção com o diesel mineral, ou puro. É produzido por meio de processos químicos, normalmente por transesterificação, no qual é removida a glicerina. Este trabalho foi realizado com o objetivo de avaliar o desempenho de um motor de ciclo diesel quatro tempos e quatro cilindros, utilizando biodiesel de óleo de oliva (B100, em comparação ao óleo diesel. Foram analisados os parâmetros: potência efetiva e reduzida, torque, consumo específico e energético de combustível, eficiência termomecânica e volumétrica. Foi instalado um ensaio com delineamento inteiramente casualizado (DIC em esquema fatorial, realizada análise de variância e aplicado teste de Tukey, a 5%. Foram pesquisados cinco níveis de rotação em quatro repetições (650, 570, 490, 410, 320 e 240 rpm. O motor alimentado com biodiesel de oliva apresentou torque, potencia reduzida e consumos especifico e

  12. Obesity and vehicle type as risk factors for injury caused by motor vehicle collision.

    Science.gov (United States)

    Donnelly, John P; Griffin, Russell Lee; Sathiakumar, Nalini; McGwin, Gerald

    2014-04-01

    This study sought to describe variations in the risk of motor vehicle collision (MVC) injury and death by occupant body mass index (BMI) class and vehicle type. We hypothesized that the relationship between BMI and the risk of MVC injury or mortality would be modified by vehicle type. This is a retrospective cohort study of occupants involved in MVCs using data from the Crash Injury Research and Engineering Network and the National Automotive Sampling System Crashworthiness Data System. Occupants were grouped based on vehicle body style (passenger car, sport utility vehicle, or light truck) and vehicle size (compact or normal, corresponding to below- or above-average curb weight). The relationship between occupant BMI class (underweight, normal weight, overweight, or obese) and risk of injury or mortality was examined for each vehicle type. Odds ratios (ORs) adjusted for various occupant and collision characteristics were estimated. Of an estimated 44 million occupants of MVCs sampled from 2000 to 2009, 37.1% sustained an injury. We limited our analysis to injuries achieving an Abbreviated Injury Scale (AIS) score of 2 or more severe, totaling 17 million injuries. Occupants differed substantially in terms of demographic and collision characteristics. After adjustment for confounding factors, we found that obesity was a risk factor for mortality caused by MVC (OR, 1.6; 95% confidence interval [CI], 1.2-2.0). When stratified by vehicle type, we found that obesity was a risk factor for mortality in larger vehicles, including any-sized light trucks (OR, 2.1; 95% CI, 1.3-3.5), normal-sized passenger cars (OR, 1.6; 95% CI, 1.1-2.3), and normal-sized sports utility vehicles or vans (OR, 2.0; 95% CI, 1.0-3.8). Being overweight was a risk factor in any-sized light trucks (OR, 1.5; 95% CI, 1.1-2.1). We identified a significant interaction between occupant BMI class and vehicle type in terms of MVC-related mortality risk. Both factors should be taken into account when

  13. Plug-In Hybrid Urban Delivery Truck Technology Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Miyasato, Matt [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States); Impllitti, Joseph [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States); Pascal, Amar [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States)

    2015-07-31

    The I-710 and CA-60 highways are key transportation corridors in the Southern California region that are heavily used on a daily basis by heavy duty drayage trucks that transport the cargo from the ports to the inland transportation terminals. These terminals, which include store/warehouses, inland-railways, are anywhere from 5 to 50 miles in distance from the ports. The concentrated operation of these drayage vehicles in these corridors has had and will continue to have a significant impact on the air quality in this region whereby significantly impacting the quality of life in the communities surrounding these corridors. To reduce these negative impacts it is critical that zero and near-zero emission technologies be developed and deployed in the region. A potential local market size of up to 46,000 trucks exists in the South Coast Air Basin, based on near- dock drayage trucks and trucks operating on the I-710 freeway. The South Coast Air Quality Management District (SCAQMD), California Air Resources Board (CARB) and Southern California Association of Governments (SCAG) — the agencies responsible for preparing the State Implementation Plan required under the federal Clean Air Act — have stated that to attain federal air quality standards the region will need to transition to broad use of zero and near zero emission energy sources in cars, trucks and other equipment (Southern California Association of Governments et al, 2011). SCAQMD partnered with Volvo Trucks to develop, build and demonstrate a prototype Class 8 heavy-duty plug-in hybrid drayage truck with significantly reduced emissions and fuel use. Volvo’s approach leveraged the group’s global knowledge and experience in designing and deploying electromobility products. The proprietary hybrid driveline selected for this proof of concept was integrated with multiple enhancements to the complete vehicle in order to maximize the emission and energy impact of electrification. A detailed review of all

  14. CDC Vital Signs: Motor Vehicle Crash Deaths

    Science.gov (United States)

    ... Ireland, Israel, Japan, Netherlands, New Zealand, Norway, Slovenia, Spain, Sweden, Switzerland, and the United Kingdom. Problem Motor ... 0.02-0.05%). Use advanced engineering and technology, such as: Ignition interlocks for all people convicted ...

  15. Desempenho e emissões de um motor-gerador ciclo diesel sob diferentes concentrações de biodiesel de soja Performance and emissions of a diesel engine-generator cycle under different concentrations of soybean biodiesel

    Directory of Open Access Journals (Sweden)

    Elton F. dos Reis

    2013-05-01

    Full Text Available No cenário atual brasileiro de constantes quedas de energia e iminência de uma crise no setor elétrico, a utilização de grupos geradores tem sido bastante comum no meio rural e os bicombustíveis, como o biodiesel, representam uma opção para diversificação da matriz energética. Este trabalho objetivou avaliar o uso do biodiesel de soja em diferentes concentrações em um motor de ciclo diesel sob diferentes demandas de cargas do motor. Foram utilizadas as concentrações: 5% (B5, 10% (B10, 20% (B20, 50% (B50, 75% (B75 e 100% de biodiesel (B100 em um grupo gerador a diesel, com motor de 5 Hp de quatro tempos, em diferentes condições de operação do motor, por meio de demandas de cargas elétricas: 500, 1.000, 1.500, 2.000 W e desligadas conectadas ao grupo gerador. Foram realizados ensaios para quantificação do consumo horário de combustível e da emissão de gases. As variáveis sofreram influência significativa conforme foram alteradas as cargas elétricas e as misturas de combustível. O uso do biodiesel em concentrações maiores reduz consideravelmente a emissão da maioria dos gases poluentes e se tem praticamente anulada a emissão de enxofre para concentrações acima de 65% de biodiesel.In the current scenario of constant power drops in Brazil and an imminent crisis in the electricity sector, the use of generators and biofuels such as biodiesel has been quite common in rural areas represents an option for diversification of the energy matrix. This study evaluated the use of soybean biodiesel in different concentrations in a diesel engine cycle under different demands of engine loads. Concentrations used were: 5% (B5, 10% (B10, 20% (B20, 50% (B50, 75% (B75 and 100% biodiesel (B100 in a diesel generator with engine of 5 Hp of four-stroke under different operating conditions of the engine, through the demands of electrical loads: 500, 1.000, 1.500, 2.000 W and off connected to the generator. Tests were conducted to quantify

  16. Motor gerador ciclo diesel sob cinco proporções de biodiesel com óleo diesel Engine-generator diesel cycle under five proportions of biodiesel and diesel

    Directory of Open Access Journals (Sweden)

    Marcelo J. da Silva

    2012-01-01

    Full Text Available O estudo de fontes alternativas de energia ao óleo diesel mineral, como o biodiesel, com origem renovável, é importante para o meio-ambiente e diversificação da matriz energética. Neste estudo foram levantados o consumo específico de combustível, o valor calórico do combustível e a eficiência do conjunto motor gerador da marca BRANCO em função de cargas resistivas, sob as seguintes proporções volumétricas entre o óleo diesel mineral com biodiesel: 0% (B0, 20% (B20, 40% (B40, 60% (B60 e 100% de biodiesel (B100. Para o ensaio utilizou-se motor de 7,36 kW, com gerador elétrico acoplado de 5,5 kW. As cargas utilizadas, 0,5 kW; 1,0 kW; 1,5 kW e 2,0 kW foram elevadas até 5,0 kW, oriundas de um dinamômetro de cargas resistentes. Assim, o desempenho do conjunto para cargas abaixo de 1,5 kW mostrou-se menor, pelo maior consumo específico de combustível (CEC, e redução na eficiência do conjunto motor gerador para a faixa de potência. Para as proporções de biodiesel B40, B60 e B100 os resultados descreveram redução no valor calórico e aumento do CEC. Portanto, realizando comparação das proporções de biodiesel com o óleo diesel, a proporção B20 substitui parcialmente o óleo diesel, sem perdas significativas do desempenho do motor gerador.The study of mineral diesel alternatives, such as biodiesel, a renewable fuel, is important for the environment and to diversify energy sources. This study evaluated an engine-generator BRANCO brand. Specific fuel consumption, calorific value and the overall efficiency as a function of the system load was measured, using diesel oil and biodiesel blends. The biodiesel proportions in the composition were 0% (B0, 20% (B20, 40% (B40, 60% (B60, and 100% (B100. The engine that was used during the test has a power of 7.36 kW, and the electric generator was 5.5 kW. The group was submitted to resistive loading, in the range: 0.5 kW, 1.0 kW, 1.5 kW; growing up to 5.0 kW. The results have shown

  17. Facility Bench of Stationary Engines for Study of Emissions (E65-PO) CIEMAT; Instalacion Banco de Motores Estacionarios para Estudio de Emisiones (E65-PO) CIEMAT

    Energy Technology Data Exchange (ETDEWEB)

    Rojas Garcia, E; Rodriguez Maroto, J J

    2007-07-01

    The Project of Technology of Aerosols in Generation of Energy, of the Department of Fossil Fuels of the CIEMAT, began in the year 2004, a research activity line, based on the study of the emissions coming from internal combustion engines, particularly of Diesel technology. Activity was continued by the Polluting Emissions Group of the Department of Environment, when becoming the original Project in this Group. From the concession to the Group, of the project GR/AMB/0119/2004 Evaluation of the Emissions of Biodiesel supported by the Autonomous Community of Madrid together with the European Regional Development Fund (ERDF), this activity was encourage, with the design, assembly and to get ready of the facility Bench of stationary engines for study of emissions, located in the building 65 at CIEMAT, Madrid. The present report constitutes a detailed technical description of each one of the elements that the installation Bench of stationary engines for study of emissions it integrated within the framework of the referred project (GR/AMB/0119/2004) and whose capacity includes studies of the effects of the engine, fuel, operation conditions, and methodology of sampling and measurement of emissions (gases and particles). The fundamental parts of facility describes in the present report are: engine test cell (cabin of sound insulation , ventilation and refrigeration system, anti vibrations mounting, engine, dynamometric brake), lines of preconditioning of particles and gases emissions (exhaust line, primary and secondary dilution lines, gases cleaning system...), other general parts of facility (sampling and measurement station, service lines...). The present report not only reflects the characteristics of the systems involved, but rather also in certain cases specified the procedure and reason for their choice. (Author) 10 refs.

  18. Sound engineering for diesel engines; Sound Engineering an Dieselmotoren

    Energy Technology Data Exchange (ETDEWEB)

    Enderich, A.; Fischer, R. [MAHLE Filtersysteme GmbH, Stuttgart (Germany)

    2006-07-01

    The strong acceptance for vehicles powered by turbo-charged diesel engines encourages several manufacturers to think about sportive diesel concepts. The approach of suppressing unpleasant noise by the application of distinctive insulation steps is not adequate to satisfy sportive needs. The acoustics cannot follow the engine's performance. This report documents, that it is possible to give diesel-powered vehicles a sportive sound characteristic by using an advanced MAHLE motor-sound-system with a pressure-resistant membrane and an integrated load controlled flap. With this the specific acoustic disadvantages of the diesel engine, like the ''diesel knock'' or a rough engine running can be masked. However, by the application of a motor-sound-system you must not negate the original character of the diesel engine concept, but accentuate its strong torque characteristic in the middle engine speed range. (orig.)

  19. Fuel Cell-Powered Lift Truck Fleet Deployment Projects Final Technical Report May 2014

    Energy Technology Data Exchange (ETDEWEB)

    Klingler, James J [GENCO Infrastructure Solutions, Inc.

    2014-05-06

    The overall objectives of this project were to evaluate the performance, operability and safety of fork lift trucks powered by fuel cells in large distribution centers. This was accomplished by replacing the batteries in over 350 lift trucks with fuel cells at five distribution centers operated by GENCO. The annual cost savings of lift trucks powered by fuel cell power units was between $2,400 and $5,300 per truck compared to battery powered lift trucks, excluding DOE contributions. The greatest savings were in fueling labor costs where a fuel cell powered lift truck could be fueled in a few minutes per day compared to over an hour for battery powered lift trucks which required removal and replacement of batteries. Lift truck operators where generally very satisfied with the performance of the fuel cell power units, primarily because there was no reduction in power over the duration of a shift as experienced with battery powered lift trucks. The operators also appreciated the fast and easy fueling compared to the effort and potential risk of injury associated with switching heavy batteries in and out of lift trucks. There were no safety issues with the fueling or operation of the fuel cells. Although maintenance costs for the fuel cells were higher than for batteries, these costs are expected to decrease significantly in the next generation of fuel cells, making them even more cost effective.

  20. Operations experience with the NAC-1 legal weight truck cask

    International Nuclear Information System (INIS)

    Viebrock, J.M.; Hoffman, C.C.

    1978-01-01

    The first three years of operation of Nuclear Assurance Corporation's (NAC) four (4) NAC-1 Casks have demonstrated that shipments of spent fuel, fuel rods and other highly irradiated reactor components can be moved routinely by legal weight truck transport. Shipments of these materials have involved some 800,000 miles of highway travel and cask handling at some fifteen different nuclear facilities. This paper presents details on NAC's operations experience with these casks including cask description, cask handling (loading and unloading), pre-shipment testing, facility turnaround and transit times, operator exposure, transport vehicles and shipper/carrier/cask owner responsibilities, actual experience with regard to facility interfacing requirements and operational procedures. Cask and equipment utilization is discussed together with the methods used to control operation costs and to improve the economics of truck transport

  1. Antecedents of Truck Drivers’ Job Satisfaction and Retention Proneness

    DEFF Research Database (Denmark)

    Prockl, Günter; Teller, Christoph; Kotzab, Herbert

    2017-01-01

    is statistically significant. Financial and nonfinancial job properties affect satisfaction with one's employer whereas the former shows a lower impact compared to the latter. Satisfaction with the job and one's employer impacts retention proneness. The contribution of this study was to (1) add...... to the understanding of the factors that predict retention of truck drivers in relationship to job satisfaction and (2) highlight the different roles of financial and nonfinancial job properties in this specific work context.......The aim of this study was to (1) explore the antecedents of truck drivers’ job satisfaction, (2) identify the impact of financial and nonfinancial job properties on satisfaction with the job and with one's employer, and (3) the drivers’ proneness to retaining their jobs. Based on the extant...

  2. Healthcare Programmes for Truck Drivers in Sub-Saharan Africa: A Systematic Review and Meta-Analysis.

    Science.gov (United States)

    Lalla-Edward, Samanta Tresha; Fobosi, Siyabulela Christopher; Hankins, Catherine; Case, Kelsey; Venter, W D Francois; Gomez, Gabriela

    2016-01-01

    Truck drivers have unique health needs, and by virtue of their continuous travel, experience difficulty in accessing healthcare. Currently, planning for effective care is hindered by lack of knowledge about their health needs and about the impact of on-going programmes on this population's health outcomes. We reviewed healthcare programmes implemented for sub-Saharan African truck drivers, assessed the evaluation methods, and examined impact on health outcomes. We searched scientific and institutional databases, and online search engines to include all publications describing a healthcare programme in sub-Saharan Africa where the main clients were truck drivers. We consulted experts and organisations working with mobile populations to identify unpublished reports. Forest plots of impact and outcome indicators with unadjusted risk ratios and 95% confidence intervals were created to map the impact of these programmes. We performed a subgroup analysis by type of indicator using a random-effects model to assess between-study heterogeneity. We conducted a sensitivity analysis to examine both the summary effect estimate chosen (risk difference vs. risk ratio) and model to summarise results (fixed vs. random effects). Thirty-seven publications describing 22 healthcare programmes across 30 countries were included from 5,599 unique records. All programmes had an HIV-prevention focus with only three expanding their services to cover conditions other primary healthcare services. Twelve programmes were evaluated and most evaluations assessed changes in input, output, and outcome indicators. Absence of comparison groups, preventing attribution of the effect observed to the programme and lack of biologically confirmed outcomes were the main limitations. Four programmes estimated a quantitative change in HIV prevalence or reported STI incidence, with mixed results, and one provided anecdotal evidence of changes in AIDS-related mortality and social norms. Most programmes showed

  3. Smart roadside initiative gap analysis : trucking technology literature review.

    Science.gov (United States)

    2014-04-01

    The Smart Roadside Initiative (SRI) was designed to breakdown information silos at the roadside in order to improve : motor carrier safety and mobility, as well as the operational efficiency of motor carriers and the public-sector agencies : that reg...

  4. ELECTRIC MOTORS FOR FARM USE.

    Science.gov (United States)

    Illinois Univ., Urbana. Coll. of Agriculture.

    BETWEEN 2 AND 8 HOURS ARE REQUIRED FOR USE OF THIS TEXTUAL OR REFERENCE MATERIAL ON ELECTRIC MOTORS. IT WAS DEVELOPED BY AN AGRICULTURAL EDUCATION-AGRICULTURAL ENGINEERING SPECIALIST ON THE BASIS OF CONFERENCES WITH SUBJECT MATTER SPECIALISTS, TEACHER EDUCATORS, SUPERVISORS, AND TEACHERS. THE OBJECTIVES AND SUBJECT MATTER CENTER AROUND THE…

  5. Real-Time Dispatch of Petroleum Tank Trucks

    OpenAIRE

    Gerald G. Brown; Glenn W. Graves

    1981-01-01

    A highly automated, real-time dispatch system is described which uses embedded optimization routines to replace extensive manual operations and to reduce substantially operating costs for a nation-wide fleet of petroleum tank trucks. The system is currently used in daily operations by the Order Entry and Dispatch segment of the Chevron U.S.A. Marketing System. Refined petroleum products valued at several billion dollars per year are dispatched from more than 80 bulk terminals on a fleet excee...

  6. Real-Time Dispatch of Petroleum Tank Trucks

    OpenAIRE

    Brown, Gerald G.; Graves, Glenn W.

    1981-01-01

    Management Science, 27, 1, pp. 19-32. (1982 International Management Science Achievement Award Finalist). A highly automated, real-time dispatch system is described which uses embedded optimization routines to replace extensive manual operations and to reduce substantially operating costs for a nation-wide fleet of petroleum tank trucks. The system is currently used in daily operations by the Order Entry and Dispatch segment of the Chevron U.S.A. Marketing System. Refined petroleum produ...

  7. Business plan of a food truck in Saint Petersburg

    OpenAIRE

    Zavyalova, Ekaterina

    2017-01-01

    The purpose of the thesis was to investigate how to write a proper business plan and then implement gained knowledge in creating a business plan of a food truck in Saint Petersburg. A business plan serves as a guide for an entrepreneur in the process of company establishment and enables to gain funding from potential investors. The primary objective was to study essential components of a business plan. The theoretical framework comprises of core issues on company establishment and desc...

  8. TITAN Legal Weight Truck cask preliminary design report

    International Nuclear Information System (INIS)

    1990-04-01

    The Preliminary Design of the TITAN Legal Weight Truck (LWT) Cask System and Ancillary Equipment is presented in this document. The scope of this document includes the LWT cask with fuel baskets, impact limiters, and lifting and tiedown features; the cask support system for transportation; intermodal transfer skid; personnel barrier; and cask lifting yoke assembly. The results of the tradeoff studies and evaluations that were performed during the preliminary design are presented in Appendix A to this report. 51 figs., 17 tabs

  9. Hydraulic Hybrid Parcel Delivery Truck Deployment, Testing & Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Gallo, Jean-Baptiste [Calstart Incorporated, Pasadena, CA (United States)

    2014-03-07

    Although hydraulic hybrid systems have shown promise over the last few years, commercial deployment of these systems has primarily been limited to Class 8 refuse trucks. In 2005, the Hybrid Truck Users Forum initiated the Parcel Delivery Working Group including the largest parcel delivery fleets in North America. The goal of the working group was to evaluate and accelerate commercialization of hydraulic hybrid technology for parcel delivery vehicles. FedEx Ground, Purolator and United Parcel Service (UPS) took delivery of the world’s first commercially available hydraulic hybrid parcel delivery trucks in early 2012. The vehicle chassis includes a Parker Hannifin hydraulic hybrid drive system, integrated and assembled by Freightliner Custom Chassis Corp., with a body installed by Morgan Olson. With funding from the U.S. Department of Energy, CALSTART and its project partners assessed the performance, reliability, maintainability and fleet acceptance of three pre-production Class 6 hydraulic hybrid parcel delivery vehicles using information and data from in-use data collection and on-road testing. This document reports on the deployment of these vehicles operated by FedEx Ground, Purolator and UPS. The results presented provide a comprehensive overview of the performance of commercial hydraulic hybrid vehicles in parcel delivery applications. This project also informs fleets and manufacturers on the overall performance of hydraulic hybrid vehicles, provides insights on how the technology can be both improved and more effectively used. The key findings and recommendations of this project fall into four major categories: -Performance, -Fleet deployment, -Maintenance, -Business case. Hydraulic hybrid technology is relatively new to the market, as commercial vehicles have been introduced only in the past few years in refuse and parcel delivery applications. Successful demonstration could pave the way for additional purchases of hydraulic hybrid vehicles throughout the

  10. Definition and Evaluation of Bus and Truck Automation Operations Concepts

    OpenAIRE

    Tsao, H.-S. Jacob; Botha, Jan L.

    2002-01-01

    Traffic congestion will continue to worsen and likely worsen at a faster rate than ever. People throughput and freight throughput have become critical issues for California and the rest of the nation. PATH has been funding a one-year research project entitled "Definition and Evaluation of Bus and Truck Automation Operations Concepts," proposed by the authors. This report summarizes the results of the research project achieved during the first six months. During those six months, we reviewed l...

  11. Keep on Trucking: An Entrepreneurial Approach to Intratheater Airlift

    Science.gov (United States)

    2013-02-14

    yet they must all remain effective in order to stay in business.50 Figure 3. Commercial Distribution Example: Walmart 10 As one of the...world’s largest corporations, Walmart provides a good example of an entrepreneurial logistics system (Figure 3). Like the deployed Air Force component, it...is a fleet owner, a distributor, and a retail location operator.51 While Walmart uses trucks, the AMD schedules aircraft as the primary delivery

  12. Modelado y experimentación computacional de la etapa de compresión en motores de pistones libres//Modeling and computer experiments of the compression stage in free piston engines

    Directory of Open Access Journals (Sweden)

    Genovevo Morejón-Vizcaino

    2012-09-01

    Full Text Available En este articulo se alcanzó la obtención de un prototipo analítico de la etapa de combustión de un motor de pistones libres para realizar experimentos virtuales con el propósito de arribar al nuevo conocimiento, necesario para desarrollar un motor de pistones libres multicilindro con una bomba volumétrica, que hagala función, del acumulador hidráulico que emplean los diseños actuales para la carrera de compresión, con la finalidad de mejorar la densidad de potencia y disminuir las exigencias al comportamiento dinámico de los agregados. El método empleado es el “Desarrollo de nuevos productos mecatrónicos”. Se dedujo elmodelo matemático para la etapa de la compresión y aplicando el método de los grafos dicromáticos se obtuvo un algoritmo y el prototipo analítico. Los resultados de los experimentos virtuales muestran diferentes restricciones en la geometría y los materiales a utilizar así como las tendencias en el comportamiento de los diferentes parámetros hidráulicos.Palabras claves: motores de pistones libres, experimentos computacionales, prototipos analíticos, modelos matemáticos, oleohidráulica._____________________________________________________________________________AbstractThe goal of the investigation is the development of a free piston engine with an auxiliary hydraulic bomb that substitutes the function of the hydraulic accumulator with the objective of to improve the density of power and to diminish the demands in the dynamic behavior of the components. The used method is the“Development of new products mecatrónicos". In the investigation to arrive to the new knowledge an analytic prototype is developed to carry out PC-experiments. The mathematical model is deduced for the stage of the compression, the algorithm and the analytic prototype was obtained. The results of theexperiments show different restrictions in the geometry and the materials to use as well as the tendencies in the behavior of the

  13. Stationary engine test of diesel cycle using diesel oil and biodiesel (B100); Ensaio de motores estacionarios do ciclo diesel utilizando oleo diesel e biodiesel (B100)

    Energy Technology Data Exchange (ETDEWEB)

    Torres, Ednildo Andrade [Universidade Federal da Bahia (DEQ/DEM/EP/UFBA), Salvador, BA (Brazil). Escola Politecnica. Dept. de Engenharia Quimica], Email: ednildo@ufba.br; Santos, Danilo Cardoso [Universidade Federal da Bahia (PPEQ/UFBA), Salvador, BA (Brazil). Programa de Pos-Graduacao em Engenharia Quimica; Souza, Daniel Vidigal D.; Peixoto, Leonardo Barbosa; Franca, Tiago [Universidade Federal da Bahia (DEM/UFBA), Salvador, BA (Brazil). Dept. de Engenharia Mecanica

    2006-07-01

    This work objectified to test an engine stationary of the cycle diesel, having as combustible diesel fossil and bio diesel. The characteristic curves of power, torque and emissions versus rotation of the engine was elaborated. The survey of these curves was carried through in the Laboratorio de Energia e Gas da Escola Politecnica da UFBA, which makes use of two stationary dynamometers and the one of chassis and necessary instrumentation for you analyze of the exhaustion gases. The tested engine was of the mark AGRALE, M-85 model stationary type, mono cylinder, with power NF (NBRISO 1585) Cv/kw/rpm 10/7,4/2500. The assays had been carried through in a hydraulically dynamometer mark Schenck, D-210 model. The fuel consumption was measured in a scale marks Filizola model BP-6, and too much ground handling equipment such as: water reservoir, tubings, valves controllers of volumetric outflow, sensors and measurers of rotation, torque, mass, connected to a system of acquisition of data on line. The emissions of the gases (CO, CO{sub 2}, and NOx), were measured by the analytical Tempest mark, model 100. The engine operated with oil diesel and bio diesel of oils and residual fats (OGR). In the tests, the use of the fuel derived from oil and the gotten ones from OGR was not detected significant differences how much. In this phase already it can show to the immediate possibility of the substitution of the oil diesel for bio diesel as combustible in the stationary engines of low power (author)

  14. Coordinating decentralized optimization of truck and shovel mining operations

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, R.; Fraser Forbes, J. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering; San Yip, W. [Suncor Energy, Fort McMurray, AB (Canada)

    2006-07-01

    Canada's oil sands contain the largest known reserve of oil in the world. Oil sands mining uses 3 functional processes, ore hauling, overburden removal and mechanical maintenance. The industry relies mainly on truck-and-shovel technology in its open-pit mining operations which contributes greatly to the overall mining operation cost. Coordination between operating units is crucial for achieving an enterprise-wide optimal operation level. Some of the challenges facing the industry include multiple or conflicting objectives such as minimizing the use of raw materials and energy while maximizing production. The large sets of constraints that define the feasible domain pose as challenge, as does the uncertainty in system parameters. One solution lies in assigning truck resources to various activities. This fully decentralized approach would treat the optimization of ore production, waste removal and equipment maintenance independently. It was emphasized that mine-wide optimal operation can only be achieved by coordinating ore hauling and overburden removal processes. For that reason, this presentation proposed a coordination approach for a decentralized optimization system. The approach is based on the Dantzig-Wolfe decomposition and auction-based methods that have been previously used to decompose large-scale optimization problems. The treatment of discrete variables and coordinator design was described and the method was illustrated with a simple truck and shovel mining simulation study. The approach can be applied to a wide range of applications such as coordinating decentralized optimal control systems and scheduling. 16 refs., 3 tabs., 2 figs.

  15. Image processing system for the measurement of timber truck loads

    Science.gov (United States)

    Carvalho, Fernando D.; Correia, Bento A. B.; Davies, Roger; Rodrigues, Fernando C.; Freitas, Jose C. A.

    1993-01-01

    The paper industry uses wood as its raw material. To know the quantity of wood in the pile of sawn tree trunks, every truck load entering the plant is measured to determine its volume. The objective of this procedure is to know the solid volume of wood stocked in the plant. Weighing the tree trunks has its own problems, due to their high capacity for absorbing water. Image processing techniques were used to evaluate the volume of a truck load of logs of wood. The system is based on a PC equipped with an image processing board using data flow processors. Three cameras allow image acquisition of the sides and rear of the truck. The lateral images contain information about the sectional area of the logs, and the rear image contains information about the length of the logs. The machine vision system and the implemented algorithms are described. The results being obtained with the industrial prototype that is now installed in a paper mill are also presented.

  16. Truck bomb and insider threats to nuclear facilities

    International Nuclear Information System (INIS)

    Hirsch, D.

    1987-01-01

    In the nuclear field, two the these weak links in the security chain are the truck bomb threat and the insider threat. The risks associated with terrorist use of vehicular bombs against nuclear targets surfaced (actually, resurfaced) followed the terrorist attacks on the US Embassy annex and the Marine compound in Leb Concern was expressed that similar attacks against nuclear facilities could result in substantial damage and release of radioactivity. Since the current regulations of the NRC require licensees to protect only against attacks on foot (and even then, only against very small attacking forces), shortly after the Lebanon bombings, that agency commenced an urgent rulemaking to require its licensees to protect against truck bombs. Inexplicably, that rulemaking was called off after research results indicated that the truck bomb threat to nuclear facilities was even more serious than previously thought. Even were nuclear facilities adequately protected against external attack, be the aim theft or sabotage, the greatest security risk to these sites - the threat of action by insiders - would remain. The traditional methods of protecting against the insider threat - such as the two-person rule, strict compartmentalization of vital areas, and design features that make damage to two or more redundant systems by one individual difficult - are generally expensive and have encountered substantial resistance from the nuclear industry, which has restrained the NRC from requiring them

  17. Scheduling trucks in cross docking systems with temporary storage and dock repeat truck holding pattern using genetic algorithm

    Directory of Open Access Journals (Sweden)

    Ehsan Ghobadian

    2013-02-01

    Full Text Available Cross docking is one of the most important issues in management of supply chains. In cross docking, different items delivered to a warehouse by inbound trucks are directly arranged and reorganized based on customer demands, routed and loaded into outbound trucks for delivery purposes to customers without virtually keeping them at the warehouse. If any item is kept in storage, it is normally for a short amount of time, say less than 24 hours. In this paper, we consider a special case of cross docking where there is temporary storage and implements genetic algorithm to solve the resulted problem for some realistic test problems. In our method, we first use some heuristics as initial solutions and then improve the final solution using genetic algorithm. The performance of the proposed model is compared with alternative solution strategy, the GRASP method.

  18. Performance of a diesel engine transformed to spark ignition using natural gas; Desempenho de um motor diesel convertido para utilizacao de gas natural como combustivel

    Energy Technology Data Exchange (ETDEWEB)

    Gutierrez, Ricardo H.R. [Coordenacao dos Programas de Pos-Graduacao de Engenharia (LEDAV/COPPE/UFRJ), RJ (Brazil). Lab. de Ensaios Dinamicos e Analise de Vibracao; Belchior, Carlos R.P. [Coordenacao dos Programas de Pos-Graduacao de Engenharia (LMT/COPPE/UFRJ), RJ (Brazil). Lab. de Maquinas Termicas; Sodre, Jose Ricardo [Pontificia Universidade Catolica de Minas Gerais (PUC/Minas), MG (Brazil)

    2012-07-01

    A zero-dimensional thermodynamic model for a diesel engine converted for dedicated use of natural gas was developed in this work. The computational model covers from the time of closing the inlet valve to the time of opening the exhaust valve and it was divided into three stages (compression, combustion and expansion). A model based on the first law of thermodynamics for closed cycle has been developed to study the performance of the engine. The combustion process was modeled using the equation of Wiebe. It was taken into consideration the convective heat transfer through the walls of the cylinder and the heat transfer coefficient was calculated by the Eichelberg correlation. It was also considered that the thermodynamic properties vary with temperature. To represent the gas mixture behavior inside the cylinder two approaches (Ideal Gas Equation and Van Der Waals's Real Gas Equation) were used and results compared. The computational model was validated with experimental tests. (author)

  19. MTU series 1600 HCCI engine with extremely low exhaust emissions over the entire engine map; HCCI-Motor der MTU Baureihe 1600 mit extrem niedrigen Abgasemissionen im gesamten Motorkennfeld

    Energy Technology Data Exchange (ETDEWEB)

    Teetz, Christoph; Bergmann, Dirk; Sauer, Christina; Schneemann, Arne [MTU, Friedrichshafen (Germany); Eichmeier, Johannes; Spicher, Ulrich [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany). IFKM

    2012-11-01

    The main challenge when developing off-highway engines is to keep emissions within the limits to apply in the future while maintaining low fuel consumption and low CO{sub 2} output. In the USA in particular, diesel engines in the 130 - 560 kW power range are to be subject from 2014 to EPA Tier 4 legislation, which imposes limits of 0.4 g/kWh for NO{sub x} and 0.02 g/kWh for particulate matter. Diesel units can only satisfy those requirements using a combination of in-engine measures and exhaust aftertreatment systems (SCR, particulate filters), which makes them a good deal more complex and expensive. In the face of CO{sub 2} emissions regulations and the growing demand for diesel fuel, greater emphasis is now being placed on alternative fuels. Homogeneous Charge Compression Ignition or 'HCCI' provides an alternative to complex exhaust aftertreatment systems which generates virtually no soot or nitrous oxide emissions. It does, however, present new challenges with respect to combustion control and engine load. Up to the present, it has not been possible to exploit the full potential of this combustion process over the entire engine map, since the high ignition performance of diesel fuel at high loads results in excessively early combustion and inadmissible pressure gradients. The pre-development department of MTU Friedrichshafen worked with the Institute of Internal Combustion Engines at the Karlsruhe Institute of Technology (KIT) to devise a research prototype for an industrial application which would allow semi-homogenous combustion with controlled self-ignition over the full engine map. The engine is based on a 6-cylinder version of the MTU Series 1600 unit and has a rated output of 300 kW. The fuels - gasoline or ethanol and diesel - are mixed in such a way as to avoid the disadvantages associated with most HCCI processes. Since the use of ethanol also enhances combustion efficiency, it has a two-fold positive effect on the CO{sub 2} situation. With

  20. IMPROVING THE ORGANIZATION OF THE SHOVEL-TRUCK SYSTEMS IN OPEN-PIT COAL MINES

    Directory of Open Access Journals (Sweden)

    Mark KORYAGIN

    2017-06-01

    Full Text Available The aim of the study is to reduce idle times of mining trucks and shovels in an open-pit coal mine. A heuristic algorithm for making dispatching decisions in conditions of dynamic allocation of trucks is developed. Priority parameters for choosing the shovel after the end-of-truck unloading are introduced. Also, an algorithm for searching for the optimal priority parameters to satisfy the required efficiency criterion is developed. This algorithm is based on a simulation model of a shovel-truck system. The proposed approach is applicable in terms of the group of shovels with a common dump point in various open-pit coal mines. The importance of this work lies in the fact that the proposed model takes into account the random factors related with the duration of loading and dumping, truck movement, repair of shovels and haul trucks, as well as the duration of periods between repairs.

  1. Calculation engine of the planning system for radiotherapy with microbeams; Motor de calculo del sistema de planificacion para la radioterapia con microhaces

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Rovira, I.; Sempau, J.; Bravin, A.; Prezado, Y.

    2011-07-01

    The TPS calculation engine includes a full modeling of the synchrotron source (energy spectrum, phase space and polarization of the incident photons) and transport through 42 m of optical elements to position the patient, where generating a phase space file (PSF) with the state of the particles. This PSF is used as input for the calculation of doses in a model of the patient, based on computed axial tomography (CT).

  2. Emissions treatment of diesel engines by plasma outside of balance; Tratamiento de emisiones de motores diesel por plasma fuera de equilibrio

    Energy Technology Data Exchange (ETDEWEB)

    Pacheco P, M.; Pacheco S, J.; Valdivia B, R.; Garcia R, M.; Estrada M, N. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Santana D, A. [Instituto Tecnologico y de Estudios Superiores de Monterrey, Mexico D. F. (Mexico); Lefort, B.; Le Moyne, L.; Zamilpa, C., E-mail: marquidia.pacheco@inin.gob.mx [Institut Superieur d l' Automobile et des Transports, 49 rue Madeimoiselle Bourgeois BP31, 58027 Nevers cedex (France)

    2013-07-01

    Nowadays, diesel engines are greatly developed in automobiles allowing the reduction of carbon dioxide emissions (CO{sub 2}); however high emissions of particulate matter (Mp) and nitric oxides (NO{sub x}) still remain. A technology based on non-thermal plasma to diminish toxic emissions is exposed in this work. From previous experimental and simulation results, a chemical mechanism is proposed showing a rapidly diminution of Mp and NO{sub x}, in presence of plasma. (Author)

  3. Improvement in the production of cylinder shirt of inner diesel combustion engines; Mejoras en la construccion de camisas de cilindro de motores de combustion interna ciclo diesel

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Perez, F.; Barroso-Moreno, A.

    2013-06-01

    This study deals with the different types of wear as well as other parameters present in the tribological system piston segment- cylinder in a combustion engine. By means of engineering methods were defined the wear rates in the three components of the system. The biggest wear in the analysis resulted in the cylinder shirt. Specialized methods applied were used to analyze the prevailing metallographic characteristics in its original construction, obtaining a gray melted iron with perlitic matrix. A new material with bainitic matrix has been proposed for increasing wear resistance. To demonstrate the efficiency of this new product, the experimental techniques carried out, were based on a dynamometric testing in a internal combustion engine diesel cycle Scania of 150 kW. It was exposed to a full charge during 500 h with 30 % of potency rising. Compared with the perlitic one, it has been proved that the bainitic matrix allows a better result. Besides, a superior dimensional stability was obtained. The piston segments had a similar wear rate in both materials in reference to the original tribological pair of the project. (Author)

  4. 75 FR 39045 - New United Motor Manufacturing, Inc., Formerly a Joint Venture of General Motors Corporation and...

    Science.gov (United States)

    2010-07-07

    ... Manufacturing, Inc., Formerly a Joint Venture of General Motors Corporation and Toyota Motor Corporation, Including On- Site Leased Workers From Corestaff, ABM Janitorial, Toyota Engineering and Manufacturing North... Corporation and Toyota Motor Corporation, including on-site leased workers from Corestaff, ABM Janitorial, and...

  5. Planning of Truck Platoons: a Literature Review and Directions for Future Research

    OpenAIRE

    Kishore Bhoopalam, Anirudh; Agatz, Niels; Zuidwijk, Rob

    2017-01-01

    textabstractA truck platoon is a set of virtually linked trucks that drive closely behind one another using automated driving technology. Benefits of truck platooning include cost savings, reduced emissions, and more efficient utilization of road capacity. To fully reap these benefits in the initial phases requires careful planning of platoons based on trucks’ itineraries and time schedules. This paper provides a framework to classify various new transportation planning problems that arise in...

  6. Assessing crash risk considering vehicle interactions with trucks using point detector data.

    Science.gov (United States)

    Hyun, Kyung Kate; Jeong, Kyungsoo; Tok, Andre; Ritchie, Stephen G

    2018-03-12

    Trucks have distinct driving characteristics in general traffic streams such as lower speeds and limitations in acceleration and deceleration. As a consequence, vehicles keep longer headways or frequently change lane when they follow a truck, which is expected to increase crash risk. This study introduces several traffic measures at the individual vehicle level to capture vehicle interactions between trucks and non-trucks and analyzed how the measures affect crash risk under different traffic conditions. The traffic measures were developed using headways obtained from Inductive Loop Detectors (ILDs). In addition, a truck detection algorithm using a Gaussian Mixture (GM) model was developed to identify trucks and to estimate truck exposure from ILD data. Using the identified vehicle types from the GM model, vehicle interaction metrics were categorized into three groups based on the combination of leading and following vehicle types. The effects of the proposed traffic measures on crash risk were modeled in two different cases of prior- and non-crash using a case-control approach utilizing a conditional logistic regression. Results showed that the vehicle interactions between the leading and following vehicle types were highly associated with crash risk, and further showed different impacts on crash risk by traffic conditions. Specifically, crashes were more likely to occur when a truck following a non-truck had shorter average headway but greater headway variance in heavy traffic while a non-truck following a truck had greater headway variance in light traffic. This study obtained meaningful conclusions that vehicle interactions involved with trucks were significantly related to the crash likelihood rather than the measures that estimate average traffic condition such as total volume or average headway of the traffic stream. Copyright © 2018 Elsevier Ltd. All rights reserved.

  7. Jidosha's Motors

    OpenAIRE

    Shirakawa Okuma, Rosely; Calderón Orejuela, Javier

    2016-01-01

    La tesis narra la situación de una empresa concesionaria de vehículos nuevos, Jidosha's Motors, perteneciente a una corporación japonesa que cuenta con una cultura muy arraigada de ética y de cumplimiento. Se plantean respuestas, se identifican problemas y sus alternativas de solución para una toma adecuada de decisiones por parte de los directivos, siguiendo una estructura de análisis de situaciones de negocios (ASN). Tesis

  8. An innovative food truck chain, strategic planning inspired from the lean start up methodology

    OpenAIRE

    Peñate, Paul Tavares

    2015-01-01

    Mestardo em Marketing Suportada pela abordagem Lean , o Projecto apresenta um modelo de negócios de uma nova marca de Food Truck, inicialmente a ser lançada na Bélgca. Foodies’TruckZ é a marca sugerida para um novo modelo de negócio de Food Truck que procura inovar alavancando economias de escala, sobretudo em Marketing, e através de uma frota co-propriedade das carinhas food truck. Neste modelo de negócio a partilha no investimento do camião, na comunicação e outros aspectos de marketing ...

  9. Electric urban delivery trucks: energy use, greenhouse gas emissions, and cost-effectiveness.

    Science.gov (United States)

    Lee, Dong-Yeon; Thomas, Valerie M; Brown, Marilyn A

    2013-07-16

    We compare electric and diesel urban delivery trucks in terms of life-cycle energy consumption, greenhouse gas (GHG) emissions, and total cost of ownership (TCO). The relative benefits of electric trucks depend heavily on vehicle efficiency associated with drive cycle, diesel fuel price, travel demand, electric drive battery replacement and price, electricity generation and transmission efficiency, electric truck recharging infrastructure, and purchase price. For a drive cycle with frequent stops and low average speed such as the New York City Cycle (NYCC), electric trucks emit 42-61% less GHGs and consume 32-54% less energy than diesel trucks, depending upon vehicle efficiency cases. Over an array of possible conditions, the median TCO of electric trucks is 22% less than that of diesel trucks on the NYCC. For a drive cycle with less frequent stops and high average speed such as the City-Suburban Heavy Vehicle Cycle (CSHVC), electric trucks emit 19-43% less GHGs and consume 5-34% less energy, but cost 1% more than diesel counterparts. Considering current and projected U.S. regional electricity generation mixes, for the baseline case, the energy use and GHG emissions ratios of electric to diesel trucks range from 48 to 82% and 25 to 89%, respectively.

  10. Was It Really Worth Pain? Refurbishment of Mercedes-Benz Trucks by Botswana Defence Force

    National Research Council Canada - National Science Library

    Rangobana, Samuel A; Alkebaisi, Hussain K

    2005-01-01

    .... Logistics statistics, for refurbished trucks returned to user units, are also gathered from the asset management software database, Mincom Ellipse, in use by the Botswana Defence Force Mechanical...

  11. Logistics of in-wood chipping and trucking of chips; Palstahaketuksen logistinen ketju

    Energy Technology Data Exchange (ETDEWEB)

    Nuuja, J. [Joensuu Univ. (Finland). Faculty of Forestry; Asikainen, A. [Metsaeosaamiskeskus, Joensuu (Finland). Joensuu Science Park

    1996-12-31

    In this study a in wood chipper and truck transport of chips were modelled and studied by discrete-event simulation. The input data, which included stand characteristics and information about transport distances was compiled by GRASS-program. This data based on the inventory done by Forestry Center TAPIO. With the model various transport alternatives were compared and the effect of work condition factors were studied. It was find out, that a long distance transport with interchangeable container truck gives better productivity than a truck with a trailer. This results from shorter loading time for the interchangeable container truck

  12. Logistics of in-wood chipping and trucking of chips; Palstahaketuksen logistinen ketju

    Energy Technology Data Exchange (ETDEWEB)

    Nuuja, J [Joensuu Univ. (Finland). Faculty of Forestry; Asikainen, A [Metsaeosaamiskeskus, Joensuu (Finland). Joensuu Science Park

    1997-12-31

    In this study a in wood chipper and truck transport of chips were modelled and studied by discrete-event simulation. The input data, which included stand characteristics and information about transport distances was compiled by GRASS-program. This data based on the inventory done by Forestry Center TAPIO. With the model various transport alternatives were compared and the effect of work condition factors were studied. It was find out, that a long distance transport with interchangeable container truck gives better productivity than a truck with a trailer. This results from shorter loading time for the interchangeable container truck

  13. Modeling, simulation, and concept design for hybrid-electric medium-size military trucks

    Science.gov (United States)

    Rizzoni, Giorgio; Josephson, John R.; Soliman, Ahmed; Hubert, Christopher; Cantemir, Codrin-Gruie; Dembski, Nicholas; Pisu, Pierluigi; Mikesell, David; Serrao, Lorenzo; Russell, James; Carroll, Mark

    2005-05-01

    A large scale design space exploration can provide valuable insight into vehicle design tradeoffs being considered for the U.S. Army"s FMTV (Family of Medium Tactical Vehicles). Through a grant from TACOM (Tank-automotive and Armaments Command), researchers have generated detailed road, surface, and grade conditions representative of the performance criteria of this medium-sized truck and constructed a virtual powertrain simulator for both conventional and hybrid variants. The simulator incorporates the latest technology among vehicle design options, including scalable ultracapacitor and NiMH battery packs as well as a variety of generator and traction motor configurations. An energy management control strategy has also been developed to provide efficiency and performance. A design space exploration for the family of vehicles involves running a large number of simulations with systematically varied vehicle design parameters, where each variant is paced through several different mission profiles and multiple attributes of performance are measured. The resulting designs are filtered to remove dominated designs, exposing the multi-criterial surface of optimality (Pareto optimal designs), and revealing the design tradeoffs as they impact vehicle performance and economy. The results are not yet definitive because ride and drivability measures were not included, and work is not finished on fine-tuning the modeled dynamics of some powertrain components. However, the work so far completed demonstrates the effectiveness of the approach to design space exploration, and the results to date suggest the powertrain configuration best suited to the FMTV mission.

  14. 49 CFR 398.4 - Driving of motor vehicles.

    Science.gov (United States)

    2010-10-01

    .... Lighting devices and reflectors. Tires. Horn. Windshield wiper or wipers. Rear-vision mirror or mirrors.... No driver or any employee of a motor carrier shall: (1) Fuel a motor vehicle with the engine running, except when it is necessary to run the engine to fuel the vehicle; (2) Smoke or expose any open flame in...

  15. Effect of turbulence intensity on PM emission of heavy duty diesel trucks - Wind tunnel studies

    Science.gov (United States)

    Littera, D.; Cozzolini, A.; Besch, M.; Carder, D.; Gautam, M.

    2017-08-01

    Stringent emission regulations have forced drastic technological improvements in diesel aftertreatment systems, particularly in reducing Particulate Matter (PM) emissions. The formation and evolution of PM from modern engines are more sensitive to overall changes in the dilution process, such as rapidity of mixing, background PM present in the air. These technological advancements were made in controlled laboratory environments compliant with measurement standards (i.e. Code of Federal Regulation CFR in the USA) and are not fully representative of real-world emissions from these engines or vehicles. In light of this, a specifically designed and built wind tunnel by West Virginia University (WVU) is used for the study of the exhaust plume of a heavy-duty diesel vehicle, providing a better insight in the dilution process and the representative nanoparticles emissions in a real-world scenario. The subsonic environmental wind tunnel is capable of accommodating a full-sized heavy-duty truck and generating wind speeds in excess of 50mph. A three-dimensional gantry system allows spanning the test section and sample regions in the plume with accuracy of less than 5 mm. The gantry system is equipped with engine exhaust gas analyzers and PM sizing instruments. The investigation involves three different heavy-duty Class-8 diesel vehicles representative of three emission regulation standards, namely a US-EPA 2007 compliant, a US-EPA 2010 compliant, and a baseline vehicle without any aftertreatment technologies as a pre US-EPA 2007, respectively. The testing procedure includes three different vehicle speeds: idling, 20mph, and 35mph. The vehicles were tested on WVU's medium-duty chassis dynamometer, with the load applied to the truck reflecting the road load equation at the corresponding vehicle test speeds. Wind tunnel wind speed and vehicle speed were maintained in close proximity to one another during the entire test. Results show that the cross-sectional plume area

  16. Evaluation of emissions in gas powered electric generator engine with vegetable oil; Avaliacao das emissoes de gases em motor gerador eletrico alimentado com oleo vegetal

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Thalita C. de; Cunha, Joao Paulo Barreto; Cotrim, Suzane Santana; Brito, Gustavo Mendes; Delmond, Josue Gomes [Universidade Estadual de Goias (UNUCET/UEG), Anapolis, GO (Brazil). Unidade Universitaria de Ciencias Exatas e Tecnologicas], E-mail: thalitacarrijo@gmail.com

    2012-11-01

    The use of vegetable oils as fuel in diesel engines is a good alternative to reduce emissions of greenhouse gases in the atmosphere from the use of fossil fuels, either in pure form or as biodiesel. The soybean, oilseed single high-availability in Brazil, is the most viable feedstock for the production of oil and its use as a fuel because of the structure of production, distribution and grain crushing. This study aimed to evaluate the performance of a duty diesel generator fueled with blends of diesel and soybean oil at concentrations of 10%, 25%, 50% and 75%, and soybean oil pure, 100%. During the tests we evaluated the energy consumption of the generator and the emission of greenhouse gases (O{sub 2}, CO, CO{sub 2}, NO{sub x} and SO{sub 2}), according to the demand of electric charges (0, 500, 1000, 1500 and 2000 Watts) connected to the group generator. The results, using the F test, showed that the hourly consumption of fuel increased with increasing concentration in the mixture of diesel fuel and engine load demand from the generator. It follows that in the environment, increasing the oil concentration in the mixture caused a reduction in emissions, except for the emission of oxygen. The best choice for the operation for the engine generator using vegetable oil soya be provided for up to 60 % oil in the mixture and load demand up to 1000W, in which occurred lower emissions of carbon monoxide (CO) and therefore improved efficiency in the combustion process. (author)

  17. THE MOTOR

    DEFF Research Database (Denmark)

    Gammelgaard Nielsen, Anders

    2011-01-01

    is dismantled in order to cast a spot- light on the individual engine com- ponents. This means that an ob- ject (the engine) is removed from its original functionality and deter- mined context and staged as an aes- thetic object via a new contextual relationship being resolved. The de- contextualisation...... something original and genuine that decisively challenges the limits of the field of architecture. This un- derstanding is important if students are to avoid mimicking an existing world of imagery in architecture or fragments of it. The point of departure for the MO- TOR assignment is that a car engine...... is dependent on a reading and analysis of the formal characteristics of the engine com- ponent. This is crucial if the staging process is to succeed....

  18. 76 FR 78808 - Airworthiness Directives; Teledyne Continental Motors (TCM) and Rolls-Royce Motors Ltd. (R-RM...

    Science.gov (United States)

    2011-12-20

    ... Airworthiness Directives; Teledyne Continental Motors (TCM) and Rolls-Royce Motors Ltd. (R-RM) Series... superseding an existing airworthiness directive (AD) for certain TCM and R-RM series reciprocating engines... adds R-RM C-125, C- 145, O-300, IO-360, TSIO-360, and LTSIO-520-AE series reciprocating engines to the...

  19. Performance of diesel engine fuelled with sunflower biodiesel blends; Desempenho de motor diesel com misturas de biodiesel de oleo de girassol

    Energy Technology Data Exchange (ETDEWEB)

    Correa, Ila Maria; Maziero, Jose Valdemar Gonzalez; Bernardi, Jose Augusto; Storino, Moises [Instituto Agronomico de Campinas (CEA/IAC), SP (Brazil). Centro de Engenharia e Automacao; Ungaro, Maria Regina [Instituto Agronomico de Campinas (IAC), SP (Brazil). Centro de Graos e Fibras

    2006-07-01

    The aim of this paper was to evaluate the use of sunflower bio diesel blends in a CI engine, direct injection. The test procedure was done in a dynamometer bench had been determined the performance of engine through power take-off (PTO) with use of diesel and sunflower bio diesel blends (B5, B10, B20 and B100). The lubricating oil was analyzed before and after period of 96 hours. The results were: D (40,7 kw; 271 g/kw.h); B5 (40,3 kw; 271 g/kw.h); B10 (39,8 kw; 277 g/kw.h); B20 (40,0 kw; 277 g/kw.h) e B100 (39,8 kw; 291 g/kw.h). It was conclude that the use of blends B5, B10, B20 and B100 decreased the power of PTO max. 2,2% and increased the fuel consumption max. 7, 3%. The analyze of lubricating oil showed that the viscosity, water content and level of iron were the parameters more affected, although it had been acceptable. (author)

  20. Consumption and combustion efficiency in a generator engine using biodiesel; Consumo e eficiencia de combustao em um motor gerador utilizando biodisel

    Energy Technology Data Exchange (ETDEWEB)

    Cunha, Joao Paulo Barreto; Delmond, Josue G.; Couto, Rodney Ferreira; Neiva Filho, Neyber Cristiano; Reis, Elton F. dos [Universidade Estadual de Goias (UNUCET/UEG), Anapolis, GO (Brazil). Unidade Universitaria de Ciencias Exatas e Tecnologicas], Email: bcunha_2@hotmail.com

    2011-07-01

    Due to the increasing demand for biodiesel, associated to the aim of reduction in pollutants emissions, technical feasibility studies are increasingly needed. This study aimed to evaluate the use of biodiesel in different concentrations (B5, B10, B20, B50, B75 and B100) in a diesel generator set, with an engine with 3,73 KW four-stroke with direct injection. Assays were performed to quantify the hourly fuel consumption and emission of gases under different conditions of engine operation, through demands of electrical loads (500 W, 1.000W, 1.500W, 2,000 W and off) connected to the generator group. A completely randomized design was used with 5x6 factorial arrangement of treatment, six of biodiesel blends and five electric load demands, with three repetitions. The results demonstrated that the mixtures showed a significant difference in fuel consumption and combustion efficiency, and revealed that the use of biodiesel in higher concentrations in general provided a combustion process more efficient compared to conventional diesel. (author)

  1. Motor-park people shift gear.

    Science.gov (United States)

    Nnoli, C

    1992-01-01

    White, U.S. homosexual males were primarily affected in the early stages of the AIDS pandemic. Some Western researchers argued, however, that the syndrome originated in Africa. Strong political and social response to this notion resulted in only an anemic response to the growing AIDS epidemic in Nigeria. Nonetheless, the Stop AIDS Organization finally launched the Motor Park AIDS Education Program (MPAEP) in 1988, for health and education outreach to populations at risk of STDs and HIV infection. Specifically targeted are long-distance truck drivers, their young male assistants known as motor boys, and the barmaids, prostitutes, and homeless juveniles who frequent motor parks where these drivers rest while on the road. Many of these long-haul drivers have unprotected casual and commercial sex, both homosexual and heterosexual, take drugs, and suffer high rates of STDs. Marginalized, 75% illiterate, and speaking a variety of languages, these populations tend to be largely ignorant of the incurable nature of AIDS. Over 45% of motor park populations are estimated to be infected with an STD, or to have a future re-infection. These drivers are optimal vectors for the spread of HIV both internationally and within Nigeria. MPAEP workers work 6 days/week in the larger interstate motor parks to reach out to their predominantly male customers. They meet a host of primary health needs, and refer STD clients for testing and treatment. Drug use and homosexuality are 2 topics of discussion especially taboo in African society which have nonetheless been vigorously researched by MPAEP. Many drivers are unacknowledged bisexuals who have sex with their motor boys. Workers therefore explain the need to use condoms in same-sex activity without specifically mentioning homosexuality. Many Nigerians deny the existence of HIV and AIDS, are reluctant to speak about sex, and consider MPAEP workers to be intruders. Despite opposition in Muslim- dominated Northern Nigeria, however, program

  2. Cálculo de la temperatura en el interior de la cámara de combustión en motores de combustión interna. // Calculation of temperature into combustion chamber of internal combustion engines.

    Directory of Open Access Journals (Sweden)

    F. Soto Pau

    2002-05-01

    Full Text Available El trabajo aquí presentado tiene como objetivo llegar a expresiones de cálculo de la temperatura en el interior de la cámarade combustión como vía de diagnostico de la combustión en motores térmicos. Este trabajo consiste en un modelo físicomatemático,el cual usa como herramientas fundamentalmente, los valores de presión medidos en el interior de la cámarade combustión, las características geométricas del motor y todos los valores normalmente medidos en el bancodinamométrico. El procesamiento teórico de este modelo consiste fundamentalmente en la determinación de la evoluciónde la combustión a partir de la curva de presión, basada en la Primera Ley de la Termodinámica, adoptando Modelo deGases Perfectos. A partir de la posición angular de cierre de la válvula de admisión es posible calcular la derivada de latemperatura en relación a la posición angular del cigüeñal para los gases quemados T&b y no quemados T&u . Teniendo estosvalores de T&u y T&b calculados, es posible integrar numéricamente las temperaturas utilizando el método de integración deEuler. Conociendo la composición química del combustible, es posible calcular la temperatura adiabática de llama, estesería el valor de temperatura inicial Tb que nos permitiría calcular un valor de entalpía específica de los gases quemados. Deigual forma con el valor de la temperatura inicial para los gases no quemados Tu se tiene el valor de temperatura inicial parael proceso de integración.Palabras claves: Proceso de combustión en motores térmicos, temperatura en el interior de la cámara decombustión, presión en el interior de la cámara de combustión.____________________________________________________________________________Abstract.This paper presents calculation expressions of the temperature inside the combustion chamber in order to diagnose thecombustion in termic engines. This analysis consists in a physical-mathematical model, which uses

  3. Reducing Auxiliary Energy Consumption of Heavy Trucks by Onboard Prediction and Real-time Optimization

    OpenAIRE

    Khodabakhshian, Mohammad; Feng, Lei; Börjesson, Stefan; Lindgärde, Olof; Wikander, Jan

    2017-01-01

    The electric engine cooling system, where the coolant pump and the radiator fan are driven by electric motors, admits advanced control methods to decrease auxiliary energy consumption. Recent publications show the fuel saving potential of optimal control strategies for the electric cooling system through offline simulations. These strategies often assume full knowledge of the drive cycle and compute the optimal control sequence by expensive global optimization methods. In reality, the full dr...

  4. Aberrant Behaviors and Road Accidents among Iranian Truck Drivers, 2010

    Directory of Open Access Journals (Sweden)

    Amir Houshang Mehrparvar

    2011-12-01

    Full Text Available structural dimensions of which as well as technologic failures such as road quality, and tech-nical faults of automobiles, need to be assessed in detail. Iran has the first order in the world for deadly road accidents. This study was designed to assess the association between aberrant behaviors of truck drivers and the incidence of road accidents in Yazd, center of Iran, in 2010.Methods: This cross-sectional descriptive-analytic study was conducted on 300 truck drivers in Yazd. We used 3 questionnaires, including one for demographic data, Driver Behavior Questionnaire (DBQ, and one for drivers' self-evaluation of the of their driving.Results: Five types of the behavior had the highest frequency: Misjudge speed of oncoming vehicle when overtaking.; Deliberately disregard the speed limits late at night or very early in the morning.; Ignore 'give way' signs, and narrowly avoid colliding with traffic having right of way.; Stuck behind a slow-moving vehicle on a two-lane highway, you are driven by frustration to try to overtake in risky circumstances.; Drive with only 'half-an-eye' on the road while looking at a map, changing a cassette or radio channel, etc. The more the driver's driv-ing was influenced by emotional and mental states the more deliberate violations and slips.Conclusion: Among truck drivers, safety has not developed sufficiently, and because of the dangers of road accidents both for the drivers and other people and its economic losses, the importance of the presenting some solutions is completely obvious.

  5. Psychoactive substance use by truck drivers: a systematic review.

    Science.gov (United States)

    Girotto, Edmarlon; Mesas, Arthur Eumann; de Andrade, Selma Maffei; Birolim, Marcela Maria

    2014-01-01

    The aim of this study was to summarise the scientific evidence on the prevalence of psychoactive substance use and on the factors associated with their intake among truck drivers. A systematic review was performed in the databases PubMed, Scientific Electronic Library Online, Latin American and Caribbean Health Sciences, and Cochrane and 36 cross-sectional studies were identified with quantitative results about the use of psychoactive substances by truck drivers. Out of these, 28 were carried out in countries with large land areas and 23 obtained their information through self-reporting. The most frequently studied substances were alcohol (n=25), amphetamines (n=17), marijuana (n=16) and cocaine (n=13). The prevalence of the use of these substances greatly varied: alcohol (0.1-91.0%); amphetamines (0.2-82.5%), marijuana (0.2-29.9%), cocaine (0.1-8.3%). The frequency of substance use was lower in studies that investigated the presence of these substances in biological samples than in those based on self-reported use. In 12 studies that evaluated factors associated with the intake of psychoactive substances, the following stood out: younger age, higher income, longer trips, alcohol consumption, driving in the night shift, travelling interstate routes, long or short sleep, fewer hours of rest, little experience of the driver, connection with small and medium sized companies, income below levels determined by labour agreements, productivity-based earnings and prior involvement in accidents. The frequency of psychoactive substance use by truck drivers seems to be high, although that greatly varies according to the type of substance and the method of collecting the information. The use of these substances was mainly associated with indicators of poor working conditions.

  6. Assessing tether anchor labeling and usability in pickup trucks.

    Science.gov (United States)

    Klinich, Kathleen D; Manary, Miriam A; Malik, Laura A; Flannagan, Carol A; Jermakian, Jessica S

    2018-04-03

    The objective of this study was to investigate vehicle factors associated with child restraint tether use and misuse in pickup trucks and evaluate 4 labeling interventions designed to educate consumers on proper tether use. Volunteer testing was performed with 24 subjects and 4 different pickup trucks. Each subject performed 8 child restraint installations among the 4 pickups using 2 forward-facing restraints: a Britax Marathon G4.1 and an Evenflo Triumph. Vehicles were selected to represent 4 different implementations of tether anchors among pickups: plastic loop routers (Chevrolet Silverado), webbing routers (Ram), back wall anchors (Nissan Frontier), and webbing routers plus metal anchors (Toyota Tundra). Interventions included a diagram label, Quick Response (QR) Code linked to video instruction, coordinating text label, and contrasting text tag. Subjects used the child restraint tether in 93% of trials. However, tether use was completely correct in only 9% of trials. An installation was considered functional if the subject attached the tether to a tether anchor and had a tight installation (ignoring routing and head restraint position); 28% of subjects achieved a functional installation. The most common installation error was attaching the tether hook to the anchor/router directly behind the child restraint (near the top of the seatback) rather than placing the tether through the router and attaching it to the anchor in the adjacent seating position. The Nissan Frontier, with the anchor located on the back wall of the cab, had the highest rate of correct installations but also had the highest rate of attaching the tether to components other than the tether anchor (seat adjustor, child restraint storage hook, around head restraint). None of the labeling interventions had a significant effect on correct installation; not a single subject scanned the QR Code to access the video instruction. Subjects with the most successful installations spent extensive time

  7. 49 CFR 399.203 - Applicability.

    Science.gov (United States)

    2010-10-01

    ... STANDARDS Step, Handhold, and Deck Requirements for Commercial Motor Vehicles § 399.203 Applicability. This subpart applies to all trucks and truck-tractors, having a high profile cab-over-engine (COE...

  8. Evaluating the effects of heavy sugar cane truck operations on repair cost of low volume highways : technical summary report.

    Science.gov (United States)

    2008-10-01

    Current Louisiana state laws allow truck operators hauling certain agricultural commodities to purchase : overweight permits and haul at gross vehicle weights (GVW) in excess of the legislated GVW limit of : 80,000 lb. For instance, sugar cane trucke...

  9. The application of smart phone, weight-mile truck data to support freight-modeling, performance measures and planning.

    Science.gov (United States)

    2013-08-01

    Oregon is one of the few states that currently charge a commercial truck weight-mile tax (WMT). The Oregon Department of : Transportation (ODOT) has developed a data-collection system Truck Road Use Electronics (TRUE) to simplify WMT : collec...

  10. 76 FR 22154 - Powered Industrial Trucks Standard; Extension of the Office of Management and Budget's (OMB...

    Science.gov (United States)

    2011-04-20

    ... manufacturer, paragraph (a)(5) mandates that employers provide a marker on the trucks that identifies the... markers required by paragraphs (a)(3) through (a)(5) remain affixed to trucks and are legible. Paragraphs... . Therefore, OSHA cautions commenters about submitting personal information such as social security numbers...

  11. Research on tractive power of KZC-5 rear dump truck in underground mine

    International Nuclear Information System (INIS)

    Lei Zeyong

    2003-01-01

    The tractive power of KZC-5 rear dump truck in underground mine is studied in this paper. The principles and ways of defining the power are discussed. It is proved that the power of KZC-5 rear dump truck in underground mine is reasonable in the industrial scale test

  12. 27 CFR 24.230 - Examination of tank car or tank truck.

    Science.gov (United States)

    2010-04-01

    ... TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Spirits § 24.230 Examination of tank car or tank truck. Upon arrival of a tank car or tank truck at the bonded wine premises, the proprietor shall... calibration chart is available at the bonded wine premises, the spirits may be gauged by volume in the tank...

  13. Risk of commercial truck fires in the United States : an exploratory data analysis

    Science.gov (United States)

    2012-06-29

    Large trucks are involved in only 8 percent of fatal crashes per year, but 17 percent of fatal fires. The scope of the current body of research is limited. Studies have treated truck fires generally as a subset of vehicle fires or in their own right ...

  14. 49 CFR 230.108 - Steam locomotive leading and trailing trucks.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Steam locomotive leading and trailing trucks. 230... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Steam Locomotives and Tenders Trucks, Frames and Equalizing System § 230.108 Steam locomotive leading...

  15. Locomotor diseases among male long-haul truck drivers and other professional drivers

    DEFF Research Database (Denmark)

    Jensen, Anker; Kaerlev, Linda; Tüchsen, Finn

    2007-01-01

    -249) and for other truck drivers (SHR: 130, 95% CI: 108-156) compared to bus drivers (SHR: 110, 95% CI: 79-149). All drivers had high SHR for lesions of the ulnar nerve (SHR: 159, 95% CI: 119-207), especially bus drivers (SHR: 197, 95% CI: 116-311). Long-haul truck drivers had high SHRs for synovitis and bursitis...

  16. A Comparative Study of Back Pain among Taxi and Truck Drivers in ...

    African Journals Online (AJOL)

    Data was analyzed using SSPSS version 20. Descriptive and analytical statistics to analyze and present data. The prevalence of back pain in Port Harcourt for taxi drivers was 70.4% and 71.4% for truck drivers. The prevalence among truck drivers was due to age ,sitting position and shock absorbers. However variables like ...

  17. Trucks involved in fatal accidents codebook 2010 (Version October 22, 2012).

    Science.gov (United States)

    2012-11-01

    This report provides documentation for UMTRIs file of Trucks Involved in Fatal Accidents : (TIFA), 2010, including distributions of the code values for each variable in the file. The 2010 : TIFA file is a census of all medium and heavy trucks invo...

  18. The Impact of Wireless Technology on Loading Trucks at an Auto Parts Distribution Center

    Science.gov (United States)

    Goomas, David T.

    2012-01-01

    An intervention was introduced for truck loaders that used wireless vehicle mount computers that included auditory, visual feedback, and immediate data delivery. The implementation reliably reduced pallets from being loaded out of sequence for all outbound trucks in multistop routes. The role of the organizational behavior management (OBM)…

  19. Impact of trucking network flow on preferred biorefinery locations in the southern United States

    Science.gov (United States)

    Timothy M. Young; Lee D. Han; James H. Perdue; Stephanie R. Hargrove; Frank M. Guess; Xia Huang; Chung-Hao Chen

    2017-01-01

    The impact of the trucking transportation network flow was modeled for the southern United States. The study addresses a gap in existing research by applying a Bayesian logistic regression and Geographic Information System (GIS) geospatial analysis to predict biorefinery site locations. A one-way trucking cost assuming a 128.8 km (80-mile) haul distance was estimated...

  20. Structural evaluation for the core sampling trucks, RMCS operations, 200 Area

    International Nuclear Information System (INIS)

    Islam, M.A.

    1996-01-01

    This report evaluates the structural adequacy and the integrity of the existing core sampling trucks to withstand impact should the trucks drop off the ramp, either onto the soft ground or onto a non-yielding surface due to operational error, wind, or earthquake. The report also addresses if the allowable tank dome load will be exceeded by the addition of the impact load