WorldWideScience

Sample records for monoxide tracer methods

  1. Carbon monoxide : A quantitative tracer for fossil fuel CO2?

    NARCIS (Netherlands)

    Gamnitzer, Ulrike; Karstens, Ute; Kromer, Bernd; Neubert, Rolf E. M.; Meijer, Harro A. J.; Schroeder, Hartwig; Levin, Ingeborg

    2006-01-01

    Carbon monoxide (CO), carbon dioxide (CO2), and radiocarbon ((CO2)-C-14) measurements have been made in Heidelberg from 2001 to 2004 in order to determine the regional fossil fuel CO2 component and to investigate the application of CO as a quantitative tracer for fossil fuel CO2 (CO2(foss)). The obs

  2. Chemical Tracer Methods: Chapter 7

    Science.gov (United States)

    Healy, Richard W.

    2017-01-01

    Tracers have a wide variety of uses in hydrologic studies: providing quantitative or qualitative estimates of recharge, identifying sources of recharge, providing information on velocities and travel times of water movement, assessing the importance of preferential flow paths, providing information on hydrodynamic dispersion, and providing data for calibration of water flow and solute-transport models (Walker, 1998; Cook and Herczeg, 2000; Scanlon et al., 2002b). Tracers generally are ions, isotopes, or gases that move with water and that can be detected in the atmosphere, in surface waters, and in the subsurface. Heat also is transported by water; therefore, temperatures can be used to trace water movement. This chapter focuses on the use of chemical and isotopic tracers in the subsurface to estimate recharge. Tracer use in surface-water studies to determine groundwater discharge to streams is addressed in Chapter 4; the use of temperature as a tracer is described in Chapter 8.Following the nomenclature of Scanlon et al. (2002b), tracers are grouped into three categories: natural environmental tracers, historical tracers, and applied tracers. Natural environmental tracers are those that are transported to or created within the atmosphere under natural processes; these tracers are carried to the Earth’s surface as wet or dry atmospheric deposition. The most commonly used natural environmental tracer is chloride (Cl) (Allison and Hughes, 1978). Ocean water, through the process of evaporation, is the primary source of atmospheric Cl. Other tracers in this category include chlorine-36 (36Cl) and tritium (3H); these two isotopes are produced naturally in the Earth’s atmosphere; however, there are additional anthropogenic sources of them.

  3. Transport pathways of carbon monoxide in the Asian summer monsoon diagnosed from Model of Ozone and Related Tracers (MOZART)

    Science.gov (United States)

    Park, Mijeong; Randel, William J.; Emmons, Louisa K.; Livesey, Nathaniel J.

    2009-04-01

    Satellite observations of tropospheric chemical constituents (such as carbon monoxide, CO) reveal a persistent maximum in the upper troposphere-lower stratosphere (UTLS) associated with the Asian summer monsoon anticyclone. Diagnostic studies suggest that the strong anticyclonic circulation acts to confine air masses, but the sources of pollution and transport pathways to altitudes near the tropopause are the subject of debate. Here we use the Model for Ozone and Related Tracers 4 (MOZART-4) global chemistry transport model, driven by analyzed meteorological fields, to study the source and transport of CO in the Asian monsoon circulation. A MOZART-4 simulation for one summer is performed, and results are compared with satellite observations of CO from the Aura Microwave Limb Sounder and the Atmospheric Chemistry Experiment Fourier Transform Spectrometer. Overall, good agreement is found between the modeled and observed CO in the UTLS, promoting confidence in the model simulation. The model results are then analyzed to understand the sources and transport pathways of CO in the Asian monsoon region, and within the anticyclone in particular. The results show that CO is transported upward by monsoon deep convection, with the main surface sources from India and Southeast Asia. The uppermost altitude of the convective transport is ˜12 km, near the level of main deep convective outflow, and much of the CO is then advected in the upper troposphere northeastward across the Pacific Ocean and southwestward with the cross-equatorial Hadley flow. However, some of the CO is also advected vertically to altitudes near the tropopause (˜16 km) by the large-scale upward circulation on the eastern side of the anticyclone, and this air then becomes trapped within the anticyclone (to the west of the convection, extending to the Middle East). Within the anticyclone, the modeled CO shows a relative maximum near 15 km, in good agreement with observations.

  4. A theoretical framework of tracer methods for marine sediment dynamics

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A new theoretical framework of tracer methods is proposed in the present contribution, on the basis of mass conservation. This model is applicable for both artificial and natural tracers. It can be used to calculate the spatial distribution patterns of sediment transport rate, thus providing independent information and verification for the results derived from empirical formulae. For the procedures of the calculation, first, the tracer concentration and topographic maps of two times are obtained. Then, the spatial and temporal changes in the concentration and seabed elevation are calculated, and the boundary conditions required are determined by field observations (such as flow and bedform migration measurements). Finally, based upon eqs. (1) and (13), the transport rate is calculated and expressed as a function of the position over the study area. Further, appropriate modifications to the model may allow the tracer to have different densities and grain size distributions from the bulk sediment.

  5. Methods and systems using encapsulated tracers and chemicals for reservoir interrogation and manipulation

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Jeffery; Aines, Roger D; Duoss, Eric B; Spadaccini, Christopher M

    2014-11-04

    An apparatus, method, and system of reservoir interrogation. A tracer is encapsulating in a receptacle. The receptacle containing the tracer is injected into the reservoir. The tracer is analyzed for reservoir interrogation.

  6. A Systematic Method For Tracer Test Analysis: An Example Using Beowawe Tracer Data

    Energy Technology Data Exchange (ETDEWEB)

    G. Michael Shook

    2005-01-01

    Quantitative analysis of tracer data using moment analysis requires a strict adherence to a set of rules which include data normalization, correction for thermal decay, deconvolution, extrapolation, and integration. If done correctly, the method yields specific information on swept pore volume, flow geometry and fluid velocity, and an understanding of the nature of reservoir boundaries. All calculations required for the interpretation can be done in a spreadsheet. The steps required for moment analysis are reviewed in this paper. Data taken from the literature is used in an example calculation.

  7. Method of removing nitrogen monoxide from a nitrogen monoxide-containing gas using a water-soluble iron ion-dithiocarbamate, xanthate or thioxanthate

    Science.gov (United States)

    Liu, D. Kwok-Keung; Chang, Shih-Ger

    1987-08-25

    The present invention relates to a method of removing of nitrogen monoxide from a nitrogen monoxide-containing gas which method comprises contacting a nitrogen oxide-containing gas with an aqueous solution of water soluble organic compound-iron ion chelate complex. The NO absorption efficiency of ferrous urea-dithiocarbamate and ferrous diethanolamine-xanthate as a function of time, oxygen content and solution ph is presented. 3 figs., 1 tab.

  8. Tracer Methods for Characterizing Fracture Creation in Engineered Geothermal Systems

    Energy Technology Data Exchange (ETDEWEB)

    Rose, Peter [Energy & Geoscience Institute at the University of Utah, Salt Lake City, UT (United States); Harris, Joel [Univ. of Utah, Salt Lake City, UT (United States)

    2014-05-08

    The aim of this proposal is to develop, through novel high-temperature-tracing approaches, three technologies for characterizing fracture creation within Engineered Geothermal Systems (EGS). The objective of a first task is to identify, develop and demonstrate adsorbing tracers for characterizing interwell reservoir-rock surface areas and fracture spacing. The objective of a second task is to develop and demonstrate a methodology for measuring fracture surface areas adjacent to single wells. The objective of a third task is to design, fabricate and test an instrument that makes use of tracers for measuring fluid flow between newly created fractures and wellbores. In one method of deployment, it will be used to identify qualitatively which fractures were activated during a hydraulic stimulation experiment. In a second method of deployment, it will serve to measure quantitatively the rate of fluid flowing from one or more activated fracture during a production test following a hydraulic stimulation.

  9. A tracer bolus method for investigating glutamine kinetics in humans.

    Directory of Open Access Journals (Sweden)

    Maiko Mori

    Full Text Available Glutamine transport between tissues is important for the outcome of critically ill patients. Investigation of glutamine kinetics is, therefore, necessary to understand glutamine metabolism in these patients in order to improve future intervention studies. Endogenous glutamine production can be measured by continuous infusion of a glutamine tracer, which necessitates a minimum measurement time period. In order to reduce this problem, we used and validated a tracer bolus injection method. Furthermore, this method was used to measure the glutamine production in healthy volunteers in the post-absorptive state, with extra alanine and with glutamine supplementation and parenteral nutrition. Healthy volunteers received a bolus injection of [1-13C] glutamine, and blood was collected from the radial artery to measure tracer enrichment over 90 minutes. Endogenous rate of appearance (endoRa of glutamine was calculated from the enrichment decay curve and corrected for the extra glutamine supplementation. The glutamine endoRa of healthy volunteers was 6.1±0.9 µmol/kg/min in the post-absorptive state, 6.9±1.0 µmol/kg/min with extra alanyl-glutamine (p = 0.29 versus control, 6.1±0.4 µmol/kg/min with extra alanine only (p = 0.32 versus control, and 7.5±0.9 µmol/kg/min with extra alanyl-glutamine and parenteral nutrition (p = 0.049 versus control. In conclusion, a tracer bolus injection method to measure glutamine endoRa showed good reproducibility and small variation at baseline as well as during parenteral nutrition. Additionally, we showed that parenteral nutrition including alanyl-glutamine increased glutamine endoRa in healthy volunteers, which was not attributable to the alanine part of the dipeptide.

  10. Experiments to Evaluate and Implement Passive Tracer Gas Methods to Measure Ventilation Rates in Homes

    Energy Technology Data Exchange (ETDEWEB)

    Lunden, Melissa [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Faulkner, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Heredia, Elizabeth [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Cohn, Sebastian [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Dickerhoff, Darryl [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Noris, Federico [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Logue, Jennifer [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Hotchi, Toshifumi [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Singer, Brett [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sherman, Max H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-10-01

    This report documents experiments performed in three homes to assess the methodology used to determine air exchange rates using passive tracer techniques. The experiments used four different tracer gases emitted simultaneously but implemented with different spatial coverage in the home. Two different tracer gas sampling methods were used. The results characterize the factors of the execution and analysis of the passive tracer technique that affect the uncertainty in the calculated air exchange rates. These factors include uncertainties in tracer gas emission rates, differences in measured concentrations for different tracer gases, temporal and spatial variability of the concentrations, the comparison between different gas sampling methods, and the effect of different ventilation conditions.

  11. A review of methods for modelling environmental tracers in groundwater: Advantages of tracer concentration simulation

    Science.gov (United States)

    Turnadge, Chris; Smerdon, Brian D.

    2014-11-01

    Mathematical models of varying complexity have been developed since the 1960s to interpret environmental tracer concentrations in groundwater flow systems. This review examines published studies of model-based environmental tracer interpretation, the progress of different modelling approaches, and also considers the value of modelling tracer concentrations directly rather than estimations of groundwater age. Based on citation metrics generated using the Web of Science and Google Scholar reference databases, the most highly utilised interpretation approaches are lumped parameter models (421 citations), followed closely by direct age models (220 citations). A third approach is the use of mixing cell models (99 citations). Although lumped parameter models are conceptually simple and require limited data, they are unsuitable for characterising the internal dynamics of a hydrogeological system and/or under conditions where large scale anthropogenic stresses occur within a groundwater basin. Groundwater age modelling, and in particular, the simulation of environmental tracer transport that explicitly accounts for the accumulation and decay of tracer mass, has proven to be highly beneficial in constraining numerical models. Recent improvements in computing power have made numerical simulation of tracer transport feasible. We argue that, unlike directly simulated ages, the results of tracer mass transport simulation can be compared directly to observations, without needing to correct for apparent age bias or other confounding factors.

  12. The Hydration Structure of Carbon Monoxide by Ab Initio Methods

    CERN Document Server

    Awoonor-Williams, Ernest

    2016-01-01

    The solvation of carbon monoxide (CO) in liquid water is important for understanding its toxicological effects and biochemical roles. In this paper, we use ab initio molecular dynamics (AIMD) and CCSD(T)-F12 calculations to assess the accuracy of the Straub and Karplus molecular mechanical (MM) model for CO(aq). The CCSD(T)-F12 CO--H2O potential energy surfaces show that the most stable structure corresponds to water donating a hydrogen bond to the C center. The MM-calculated surface it incorrectly predicts that the O atom is a stronger hydrogen bond acceptor than the C atom. The AIMD simulations indicate that CO is solvated like a hydrophobic solute, with very limited hydrogen bonding with water. The MM model tends to overestimate the degree of hydrogen bonding and overestimates the atomic radius of the C atom. The calculated Gibbs energy of hydration is in good agreement with experiment (9.3 kJ/mol calc. vs 10.7 kJ/mol exptl.). The calculated diffusivity of CO(aq) in TIP3P-model water was 5.19 x 10-5 cm2/s ...

  13. Single well tracer method to evaluate enhanced recovery

    Science.gov (United States)

    Sheely, Jr., Clyde Q.; Baldwin, Jr., David E.

    1978-01-01

    Data useful to evaluate the effectiveness of or to design an enhanced recovery process (the recovery process involving mobilizing and moving hydrocarbons through a hydrocarbon-bearing subterranean formation from an injection well to a production well by injecting a mobilizing fluid into the injection well) are obtained by a process which comprises sequentially: determining hydrocarbon saturation in the formation in a volume in the formation near a well bore penetrating the formation, injecting sufficient of the mobilizing fluid to mobilize and move hydrocarbons from a volume in the formation near the well bore penetrating the formation, and determining by the single well tracer method a hydrocarbon saturation profile in a volume from which hydrocarbons are moved. The single well tracer method employed is disclosed by U.S. Pat. No. 3,623,842. The process is useful to evaluate surfactant floods, water floods, polymer floods, CO.sub.2 floods, caustic floods, micellar floods, and the like in the reservoir in much less time at greatly reduced costs, compared to conventional multi-well pilot test.

  14. A Lagrangian particle method with remeshing for tracer transport on the sphere

    Science.gov (United States)

    Bosler, Peter A.; Kent, James; Krasny, Robert; Jablonowski, Christiane

    2017-07-01

    A Lagrangian particle method (called LPM) based on the flow map is presented for tracer transport on the sphere. The particles carry tracer values and are located at the centers and vertices of triangular Lagrangian panels. Remeshing is applied to control particle disorder and two schemes are compared, one using direct tracer interpolation and another using inverse flow map interpolation with sampling of the initial tracer density. Test cases include a moving-vortices flow and reversing-deformational flow with both zero and nonzero divergence, as well as smooth and discontinuous tracers. We examine the accuracy of the computed tracer density and tracer integral, and preservation of nonlinear correlation in a pair of tracers. We compare results obtained using LPM and the Lin-Rood finite-volume scheme. An adaptive particle/panel refinement scheme is demonstrated.

  15. Quantifying Methane Fluxes Simply and Accurately: The Tracer Dilution Method

    Science.gov (United States)

    Rella, Christopher; Crosson, Eric; Green, Roger; Hater, Gary; Dayton, Dave; Lafleur, Rick; Merrill, Ray; Tan, Sze; Thoma, Eben

    2010-05-01

    Methane is an important atmospheric constituent with a wide variety of sources, both natural and anthropogenic, including wetlands and other water bodies, permafrost, farms, landfills, and areas with significant petrochemical exploration, drilling, transport, or processing, or refining occurs. Despite its importance to the carbon cycle, its significant impact as a greenhouse gas, and its ubiquity in modern life as a source of energy, its sources and sinks in marine and terrestrial ecosystems are only poorly understood. This is largely because high quality, quantitative measurements of methane fluxes in these different environments have not been available, due both to the lack of robust field-deployable instrumentation as well as to the fact that most significant sources of methane extend over large areas (from 10's to 1,000,000's of square meters) and are heterogeneous emitters - i.e., the methane is not emitted evenly over the area in question. Quantifying the total methane emissions from such sources becomes a tremendous challenge, compounded by the fact that atmospheric transport from emission point to detection point can be highly variable. In this presentation we describe a robust, accurate, and easy-to-deploy technique called the tracer dilution method, in which a known gas (such as acetylene, nitrous oxide, or sulfur hexafluoride) is released in the same vicinity of the methane emissions. Measurements of methane and the tracer gas are then made downwind of the release point, in the so-called far-field, where the area of methane emissions cannot be distinguished from a point source (i.e., the two gas plumes are well-mixed). In this regime, the methane emissions are given by the ratio of the two measured concentrations, multiplied by the known tracer emission rate. The challenges associated with atmospheric variability and heterogeneous methane emissions are handled automatically by the transport and dispersion of the tracer. We present detailed methane flux

  16. A tracer-based inversion method for diagnosing eddy-induced diffusivity and advection

    Science.gov (United States)

    Bachman, S. D.; Fox-Kemper, B.; Bryan, F. O.

    2015-02-01

    A diagnosis method is presented which inverts a set of tracer flux statistics into an eddy-induced transport intended to apply for all tracers. The underlying assumption is that a linear flux-gradient relationship describes eddy-induced tracer transport, but a full tensor coefficient is assumed rather than a scalar coefficient which allows for down-gradient and skew transports. Thus, Lagrangian advection and anisotropic diffusion not necessarily aligned with the tracer gradient can be diagnosed. In this method, multiple passive tracers are initialized in an eddy-resolving flow simulation. Their spatially-averaged gradients form a matrix, where the gradient of each tracer is assumed to satisfy an identical flux-gradient relationship. The resulting linear system, which is overdetermined when using more than three tracers, is then solved to obtain an eddy transport tensor R which describes the eddy advection (antisymmetric part of R) and potentially anisotropic diffusion (symmetric part of R) in terms of coarse-grained variables. The mathematical basis for this inversion method is presented here, along with practical guidelines for its implementation. We present recommendations for initialization of the passive tracers, maintaining the required misalignment of the tracer gradients, correcting for nonconservative effects, and quantifying the error in the diagnosed transport tensor. A method is proposed to find unique, tracer-independent, distinct rotational and divergent Lagrangian transport operators, but the results indicate that these operators are not meaningfully relatable to tracer-independent eddy advection or diffusion. With the optimal method of diagnosis, the diagnosed transport tensor is capable of predicting the fluxes of other tracers that are withheld from the diagnosis, including even active tracers such as buoyancy, such that relative errors of 14% or less are found.

  17. The characterization of petroleum contamination in heterogenous media using partitioning tracer method

    Energy Technology Data Exchange (ETDEWEB)

    Kim, E.; Rhee, S.; Park, J. [Seoul National Univ. (Korea, Republic of). Dept. of Civil and Environmental Engineering

    2009-07-01

    A partitioning tracer method for characterizing petroleum contamination in heterogenous media was discussed. The average saturation level of nonaqueous phase liquids (NAPLs) was calculated by comparing the transport of the partitioning tracers to a conservative tracer. The NAPL saturation level represented a continuous value throughout the contaminated site. Experiments were conducted in a 2-D sandbox divided into 4 parts using different-sized sands. Soils were contaminated with a mixture of kerosene and diesel. Partitioning tracer tests were conducted both before and after contamination. A partitioning batch test was conducted to determine the partition coefficient (K) of the tracer between the NAPL and water. Breakthrough curves were obtained, and a retardation factor (R) was calculated. Results of the study showed that the calculated NAPL saturation was in good agreement with determined values. It was concluded that the partitioning tracer test is an accurate method of locating and quantifying NAPLs.

  18. Methane emissions measured at two California landfills by OTM-10 and an acetylene tracer method

    Science.gov (United States)

    Methane emissions were measured at two municipal solid waste landfills in California using static flux chambers, an optical remote sensing approach known as vertical radial plume mapping (VRPM) using a tunable diode laser (TDL) and a novel acetylene tracer method. The tracer meth...

  19. ELUCIDATION OF HYDRODESULFURIZATION AND HYDROGENATION MECHANISMS USING RADIOISOTOPE TRACER METHODS

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    To meet the specification of sulfur and aromatic contents in diesel fuel, it is necessary for refiners to develop a new catalyst with high activity of hydrodesulfurization and hydrogenation. In the present study, the properties of noble metal catalysts for hydrodesulfurization and hydrogenation in the presence of sulfur compounds have been investigated. The hydrogenation activity of phenanthrene (PHE) on single noble metal and double noble metal catalysts—Pt/Al2O3, Pd/Al2O3 and Pd-Pt/Al2O3 in the presence of dibenzothiophene (DBT) was perforrned in a fixed bed flow reactor. The Pt based catalysts revealed the similar HDS activities and higher HYD activity compared with convertional Mo based ca-talysts. The maximum activity was obtained around 320 ℃ for both catalyst types. The Pt based catalysts produced perhydrophenanthrene as a major product at the maximum activity in the hydrogenation of PHE while the Mo based catalysts produced octahydrophenanthrene.   A  35S radioisotope pulse tracer method (35S RPTM) was used to estimate the behavior of sulfur on the working catalysts and to clarity the differences between Pt and Mo based catalysts. Very little amount of labile sulfur was accumulated on the Pt and Pd catalysts in the HDS of [35S]DBT (PtS0.25 or PdS0.25). This indicates that the mechanism of DBT HDS on noble metal catalysts is significantly different from that on conventional Mo based catalysts where Mo is present as MoS2 less than 60% of which can be labile in the case of Co-Mo/Al2O3.   Another Ru-Cs/Al2O3 catalysts were also prepared and the behavior of sulfur on the working catalyst was compared with those of Mo based catalysts and Pt and Pd catalysts. The values of labile sulfur in the HDS reaction for Ru-Cs catalysts approximately correspond to RuS0.5-0.74. These amounts of labile sulfur are much higher than those for Pt and Pd catalysts. The result suggests that the oxidation state of Ru species is present between the oxidation states

  20. Acupuncture meridians demythified. A study using the radioactive tracer method

    Energy Technology Data Exchange (ETDEWEB)

    Simon, J.; Esquerre, J.P.; Guiraud, R.; Guiraud, G.; Lazorthes, Y.

    1988-07-01

    Radioactive trajectories can be visualized by injecting a radioactive tracer, technetium 99 m, at the site of acupuncture points. To determine the exact nature of these trajectories we performed several experiments on healthy volunteers, and our results may be summarized as follows. The target organs of technetium 99 m, and notably the thyroid gland, were always visualized. The circulating radioactivity, visible on scintiscans and confirmed by venous blood counts, was not negligible. The radioactive trajectories we observed were often divided at their starting point and did not extend along the whole length of the acupuncture meridians they might have made visible. The radioactive trajectories disappeared after venous blockade to reappear when the blockade was lifted. Finally, the radioactive trajectories obtained were very similar after injection at the acupuncture point and at a control point. These findings indicate a lymphatic and venous drainage of the radioactive tracer at the site of injection followed by transportation through the veins, rather than visualization of acupuncture meridians as suggested by some authors.

  1. An unsteady state tracer method for characterizing fractures in bedrock wells.

    Science.gov (United States)

    Libby, Jill L; Robbins, Gary A

    2014-01-01

    Evaluating contaminants impacting wells in fractured crystalline rock requires knowledge of the individual fractures contributing water. This typically involves using a sequence of tools including downhole geophysics, flow meters, and straddle packers. In conjunction with each other these methods are expensive, time consuming, and can be logistically difficult to implement. This study demonstrates an unsteady state tracer method as a cost-effective alternative for gathering fracture information in wells. The method entails introducing tracer dye throughout the well, inducing fracture flow into the well by conducting a slug test and then profiling the tracer concentration in the well to locate water contributing fractures where the dye has been diluted. By monitoring the development of the dilution zones within the wellbore with time, the transmissivity and the hydraulic head of the water contributing fractures can be determined. Ambient flow conditions and the contaminant concentration within the fractures can also be determined from the tracer dilution. This method was tested on a large physical model well and a bedrock well. The model well was used to test the theory underlying the method and to refine method logistics. The approach located the fracture and generated transmissivity values that were in excellent agreement with those calculated by slug testing. For the bedrock well tested, two major active fractures were located. Fracture location and ambient well conditions matched results from conventional methods. Estimates of transmissivity values by the tracer method were within an order of magnitude of those calculated using heat-pulse flow meter data.

  2. Evaluation of multiple tracer methods to estimate low groundwater flow velocities.

    Science.gov (United States)

    Reimus, Paul W; Arnold, Bill W

    2017-04-01

    Four different tracer methods were used to estimate groundwater flow velocity at a multiple-well site in the saturated alluvium south of Yucca Mountain, Nevada: (1) two single-well tracer tests with different rest or "shut-in" periods, (2) a cross-hole tracer test with an extended flow interruption, (3) a comparison of two tracer decay curves in an injection borehole with and without pumping of a downgradient well, and (4) a natural-gradient tracer test. Such tracer methods are potentially very useful for estimating groundwater velocities when hydraulic gradients are flat (and hence uncertain) and also when water level and hydraulic conductivity data are sparse, both of which were the case at this test location. The purpose of the study was to evaluate the first three methods for their ability to provide reasonable estimates of relatively low groundwater flow velocities in such low-hydraulic-gradient environments. The natural-gradient method is generally considered to be the most robust and direct method, so it was used to provide a "ground truth" velocity estimate. However, this method usually requires several wells, so it is often not practical in systems with large depths to groundwater and correspondingly high well installation costs. The fact that a successful natural gradient test was conducted at the test location offered a unique opportunity to compare the flow velocity estimates obtained by the more easily deployed and lower risk methods with the ground-truth natural-gradient method. The groundwater flow velocity estimates from the four methods agreed very well with each other, suggesting that the first three methods all provided reasonably good estimates of groundwater flow velocity at the site. The advantages and disadvantages of the different methods, as well as some of the uncertainties associated with them are discussed. Published by Elsevier B.V.

  3. Single well surfactant test to evaluate surfactant floods using multi tracer method

    Science.gov (United States)

    Sheely, Clyde Q.

    1979-01-01

    Data useful for evaluating the effectiveness of or designing an enhanced recovery process said process involving mobilizing and moving hydrocarbons through a hydrocarbon bearing subterranean formation from an injection well to a production well by injecting a mobilizing fluid into the injection well, comprising (a) determining hydrocarbon saturation in a volume in the formation near a well bore penetrating formation, (b) injecting sufficient mobilizing fluid to mobilize and move hydrocarbons from a volume in the formation near the well bore, and (c) determining the hydrocarbon saturation in a volume including at least a part of the volume of (b) by an improved single well surfactant method comprising injecting 2 or more slugs of water containing the primary tracer separated by water slugs containing no primary tracer. Alternatively, the plurality of ester tracers can be injected in a single slug said tracers penetrating varying distances into the formation wherein the esters have different partition coefficients and essentially equal reaction times. The single well tracer method employed is disclosed in U.S. Pat. No. 3,623,842. This method designated the single well surfactant test (SWST) is useful for evaluating the effect of surfactant floods, polymer floods, carbon dioxide floods, micellar floods, caustic floods and the like in subterranean formations in much less time and at much reduced cost compared to conventional multiwell pilot tests.

  4. A new method for measuring concentration of a fluorescent tracer in bubbly gas-liquid flows

    Science.gov (United States)

    Moghaddas, J. S.; Trägårdh, C.; Kovacs, T.; Östergren, K.

    2002-06-01

    A new experimental model, the two-tracer method (TTM), based on the planar laser-induced fluorescence technique (PLIF), is presented for the measurement of the local concentration of a fluorescent tracer in the liquid phase of a bubbly two-phase system. Light scattering and shading effects due to the bubbles were compensated for using the new model. The TTM results were found to give more accurate predictions of the local concentration than the normal PLIF method in a bubbly two-phase system.

  5. Recover Act. Verification of Geothermal Tracer Methods in Highly Constrained Field Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Becker, Matthew W. [California State University, Long Beach, CA (United States)

    2014-05-16

    The prediction of the geothermal system efficiency is strong linked to the character of the flow system that connects injector and producer wells. If water flow develops channels or “short circuiting” between injection and extraction wells thermal sweep is poor and much of the reservoir is left untapped. The purpose of this project was to understand how channelized flow develops in fracture geothermal reservoirs and how it can be measured in the field. We explored two methods of assessing channelization: hydraulic connectivity tests and tracer tests. These methods were tested at a field site using two verification methods: ground penetrating radar (GPR) images of saline tracer and heat transfer measurements using distributed temperature sensing (DTS). The field site for these studies was the Altona Flat Fractured Rock Research Site located in northeastern New York State. Altona Flat Rock is an experimental site considered a geologic analog for some geothermal reservoirs given its low matrix porosity. Because soil overburden is thin, it provided unique access to saturated bedrock fractures and the ability image using GPR which does not effectively penetrate most soils. Five boreholes were drilled in a “five spot” pattern covering 100 m2 and hydraulically isolated in a single bedding plane fracture. This simple system allowed a complete characterization of the fracture. Nine small diameter boreholes were drilled from the surface to just above the fracture to allow the measurement of heat transfer between the fracture and the rock matrix. The focus of the hydraulic investigation was periodic hydraulic testing. In such tests, rather than pumping or injection in a well at a constant rate, flow is varied to produce an oscillating pressure signal. This pressure signal is sensed in other wells and the attenuation and phase lag between the source and receptor is an indication of hydraulic connection. We found that these tests were much more effective than constant

  6. Recover Act. Verification of Geothermal Tracer Methods in Highly Constrained Field Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Becker, Matthew W. [California State University, Long Beach, CA (United States)

    2014-05-16

    The prediction of the geothermal system efficiency is strong linked to the character of the flow system that connects injector and producer wells. If water flow develops channels or “short circuiting” between injection and extraction wells thermal sweep is poor and much of the reservoir is left untapped. The purpose of this project was to understand how channelized flow develops in fracture geothermal reservoirs and how it can be measured in the field. We explored two methods of assessing channelization: hydraulic connectivity tests and tracer tests. These methods were tested at a field site using two verification methods: ground penetrating radar (GPR) images of saline tracer and heat transfer measurements using distributed temperature sensing (DTS). The field site for these studies was the Altona Flat Fractured Rock Research Site located in northeastern New York State. Altona Flat Rock is an experimental site considered a geologic analog for some geothermal reservoirs given its low matrix porosity. Because soil overburden is thin, it provided unique access to saturated bedrock fractures and the ability image using GPR which does not effectively penetrate most soils. Five boreholes were drilled in a “five spot” pattern covering 100 m2 and hydraulically isolated in a single bedding plane fracture. This simple system allowed a complete characterization of the fracture. Nine small diameter boreholes were drilled from the surface to just above the fracture to allow the measurement of heat transfer between the fracture and the rock matrix. The focus of the hydraulic investigation was periodic hydraulic testing. In such tests, rather than pumping or injection in a well at a constant rate, flow is varied to produce an oscillating pressure signal. This pressure signal is sensed in other wells and the attenuation and phase lag between the source and receptor is an indication of hydraulic connection. We found that these tests were much more effective than constant

  7. Development of a Dual Tracer PET Method for Imaging Dopaminergic Neuromodulation

    Science.gov (United States)

    Converse, Alexander K.; Dejesus, Onofre T.; Flores, Leo G.; Holden, James E.; Kelley, Ann E.; Moirano, Jeffrey M.; Nickles, Robert J.; Oakes, Terrence R.; Roberts, Andrew D.; Ruth, Thomas J.; Vandehey, Nicholas T.; Davidson, Richard J.

    2006-04-01

    The modulatory neurotransmittor dopamine (DA) is involved in movement and reward behaviors, and malfunctions in the dopamine system are implicated in a variety of prevalent and debilitating pathologies including Parkinson's disease, attention deficit/hyperactivity disorder, schizophrenia, and addiction. Positron emission tomography (PET) has been used to separately measure changes in DA receptor occupancy and blood flow in response to various interventions. Here we describe a dual tracer PET method to simultaneously measure both responses with the aim of comparing DA release in particular areas of the brain and associated alterations in neural activity throughout the brain. Significant correlations between reductions in DA receptor occupancy and blood flow alterations would be potential signs of dopaminergic modulation, i.e. modifications in signal processing due to increased levels of extracellular DA. Methodological development has begun with rats undergoing an amphetamine challenge while being scanned with the blood flow tracer [17F]fluoromethane and the dopamine D2 receptor tracer [18F]desmethoxyfallypride.

  8. The complex analytical method for assessment of passive smokers' exposure to carbon monoxide.

    Science.gov (United States)

    Czogala, Jan; Goniewicz, Maciej Lukasz

    2005-01-01

    Carbon monoxide (CO) is one of the toxic constituents in tobacco smoke. The aim of the study was to evaluate a complex analytical method that allows quantification of the exposure of passive smokers to CO. The exposed volunteers were placed in the model room where portions of cigarettes (5, 10, or 15 cigarettes every 30 or 60 min over 4 h) were smoked using a homemade smoking machine. The concentrations of CO and of the ventilation marker (methane) were monitored for the duration of each experiment. CO and methane were analyzed on-line using GC-FID with methanization. Carboxyhemoglobin (COHb) was analyzed twice: just before and after the experiment. After hemolysis of a 100-microL blood sample, CO was quantitatively released by adding 10% K3[Fe(CN)6] inside a small reactor and under stable pressure transported through a microtube with an absorbing agent on a chromatography loop. The proposed analytical method allows us to quantify exposure of passive smokers by measuring the dose-effect correlation. We observed that increasing COHb levels were directly correlated with the CO concentration in the air, but were also intermediately correlated with the frequency and number of smoked cigarettes and with the ventilation coefficient.

  9. When Phase Contrast Fails: ChainTracer and NucTracer, Two ImageJ Methods for Semi-Automated Single Cell Analysis Using Membrane or DNA Staining.

    Science.gov (United States)

    Syvertsson, Simon; Vischer, Norbert O E; Gao, Yongqiang; Hamoen, Leendert W

    2016-01-01

    Within bacterial populations, genetically identical cells often behave differently. Single-cell measurement methods are required to observe this heterogeneity. Flow cytometry and fluorescence light microscopy are the primary methods to do this. However, flow cytometry requires reasonably strong fluorescence signals and is impractical when bacteria grow in cell chains. Therefore fluorescence light microscopy is often used to measure population heterogeneity in bacteria. Automatic microscopy image analysis programs typically use phase contrast images to identify cells. However, many bacteria divide by forming a cross-wall that is not detectable by phase contrast. We have developed 'ChainTracer', a method based on the ImageJ plugin ObjectJ. It can automatically identify individual cells stained by fluorescent membrane dyes, and measure fluorescence intensity, chain length, cell length, and cell diameter. As a complementary analysis method we developed 'NucTracer', which uses DAPI stained nucleoids as a proxy for single cells. The latter method is especially useful when dealing with crowded images. The methods were tested with Bacillus subtilis and Lactococcus lactis cells expressing a GFP-reporter. In conclusion, ChainTracer and NucTracer are useful single cell measurement methods when bacterial cells are difficult to distinguish with phase contrast.

  10. Advancing Reactive Tracer Methods for Measurement of Thermal Evolution in Geothermal Reservoirs: Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell A. Plummer; Carl D. Palmer; Earl D. Mattson; Laurence C. Hull; George D. Redden

    2011-07-01

    The injection of cold fluids into engineered geothermal system (EGS) and conventional geothermal reservoirs may be done to help extract heat from the subsurface or to maintain pressures within the reservoir (e.g., Rose et al., 2001). As these injected fluids move along fractures, they acquire heat from the rock matrix and remove it from the reservoir as they are extracted to the surface. A consequence of such injection is the migration of a cold-fluid front through the reservoir (Figure 1) that could eventually reach the production well and result in the lowering of the temperature of the produced fluids (thermal breakthrough). Efficient operation of an EGS as well as conventional geothermal systems involving cold-fluid injection requires accurate and timely information about thermal depletion of the reservoir in response to operation. In particular, accurate predictions of the time to thermal breakthrough and subsequent rate of thermal drawdown are necessary for reservoir management, design of fracture stimulation and well drilling programs, and forecasting of economic return. A potential method for estimating migration of a cold front between an injection well and a production well is through application of reactive tracer tests, using chemical whose rate of degradation is dependent on the reservoir temperature between the two wells (e.g., Robinson 1985). With repeated tests, the rate of migration of the thermal front can be determined, and the time to thermal breakthrough calculated. While the basic theory behind the concept of thermal tracers has been understood for some time, effective application of the method has yet to be demonstrated. This report describes results of a study that used several methods to investigate application of reactive tracers to monitoring the thermal evolution of a geothermal reservoir. These methods included (1) mathematical investigation of the sensitivity of known and hypothetical reactive tracers, (2) laboratory testing of novel

  11. Using the tracer-dilution discharge method to develop streamflow records for ice-affected streams in Colorado

    Science.gov (United States)

    Capesius, Joseph P.; Sullivan, Joseph R.; O'Neill, Gregory B.; Williams, Cory A.

    2005-01-01

    Accurate ice-affected streamflow records are difficult to obtain for several reasons, which makes the management of instream-flow water rights in the wintertime a challenging endeavor. This report documents a method to improve ice-affected streamflow records for two gaging stations in Colorado. In January and February 2002, the U.S. Geological Survey, in cooperation with the Colorado Water Conservation Board, conducted an experiment using a sodium chloride tracer to measure streamflow under ice cover by the tracer-dilution discharge method. The purpose of this study was to determine the feasibility of obtaining accurate ice-affected streamflow records by using a sodium chloride tracer that was injected into the stream. The tracer was injected at two gaging stations once per day for approximately 20 minutes for 25 days. Multiple-parameter water-quality sensors at the two gaging stations monitored background and peak chloride concentrations. These data were used to determine discharge at each site. A comparison of the current-meter streamflow record to the tracer-dilution streamflow record shows different levels of accuracy and precision of the tracer-dilution streamflow record at the two sites. At the lower elevation and warmer site, Brandon Ditch near Whitewater, the tracer-dilution method overestimated flow by an average of 14 percent, but this average is strongly biased by outliers. At the higher elevation and colder site, Keystone Gulch near Dillon, the tracer-dilution method experienced problems with the tracer solution partially freezing in the injection line. The partial freezing of the tracer contributed to the tracer-dilution method underestimating flow by 52 percent at Keystone Gulch. In addition, a tracer-pump-reliability test was conducted to test how accurately the tracer pumps can discharge the tracer solution in conditions similar to those used at the gaging stations. Although the pumps were reliable and consistent throughout the 25-day study period

  12. Measuring serotonin synthesis: from conventional methods to PET tracers and their (pre)clinical implications

    Energy Technology Data Exchange (ETDEWEB)

    Visser, Anniek K.D.; Waarde, Aren van; Willemsen, Antoon T.M. [University of Groningen, University Medical Center Groningen, Department of Nuclear Medicine and Molecular Imaging, Groningen (Netherlands); Bosker, Fokko J. [University of Groningen, University Medical Center Groningen, University Center of Psychiatry, Groningen (Netherlands); Luiten, Paul G.M. [University of Groningen, Center for Behavior and Neurosciences, Department of Molecular Neurobiology, Haren (Netherlands); Boer, Johan A. den [University of Groningen, University Medical Center Groningen, Department of Nuclear Medicine and Molecular Imaging, Groningen (Netherlands); University of Groningen, University Medical Center Groningen, University Center of Psychiatry, Groningen (Netherlands); Kema, Ido P. [University of Groningen, University Medical Center Groningen, Department of Laboratory Medicine, Groningen (Netherlands); Dierckx, Rudi A.J.O. [University of Groningen, University Medical Center Groningen, Department of Nuclear Medicine and Molecular Imaging, Groningen (Netherlands); University Hospital Ghent, Department of Nuclear Medicine, Ghent (Belgium)

    2011-03-15

    The serotonergic system of the brain is complex, with an extensive innervation pattern covering all brain regions and endowed with at least 15 different receptors (each with their particular distribution patterns), specific reuptake mechanisms and synthetic processes. Many aspects of the functioning of the serotonergic system are still unclear, partially because of the difficulty of measuring physiological processes in the living brain. In this review we give an overview of the conventional methods of measuring serotonin synthesis and methods using positron emission tomography (PET) tracers, more specifically with respect to serotonergic function in affective disorders. Conventional methods are invasive and do not directly measure synthesis rates. Although they may give insight into turnover rates, a more direct measurement may be preferred. PET is a noninvasive technique which can trace metabolic processes, like serotonin synthesis. Tracers developed for this purpose are {alpha}-[{sup 11}C]methyltryptophan ([{sup 11}C]AMT) and 5-hydroxy-L-[{beta}-{sup 11}C]tryptophan ([{sup 11}C]5-HTP). Both tracers have advantages and disadvantages. [{sup 11}C]AMT can enter the kynurenine pathway under inflammatory conditions (and thus provide a false signal), but this tracer has been used in many studies leading to novel insights regarding antidepressant action. [{sup 11}C]5-HTP is difficult to produce, but trapping of this compound may better represent serotonin synthesis. AMT and 5-HTP kinetics are differently affected by tryptophan depletion and changes of mood. This may indicate that both tracers are associated with different enzymatic processes. In conclusion, PET with radiolabelled substrates for the serotonergic pathway is the only direct way to detect changes of serotonin synthesis in the living brain. (orig.)

  13. A feature point identification method for positron emission particle tracking with multiple tracers

    Science.gov (United States)

    Wiggins, Cody; Santos, Roque; Ruggles, Arthur

    2017-01-01

    A novel detection algorithm for Positron Emission Particle Tracking (PEPT) with multiple tracers based on optical feature point identification (FPI) methods is presented. This new method, the FPI method, is compared to a previous multiple PEPT method via analyses of experimental and simulated data. The FPI method outperforms the older method in cases of large particle numbers and fine time resolution. Simulated data show the FPI method to be capable of identifying 100 particles at 0.5 mm average spatial error. Detection error is seen to vary with the inverse square root of the number of lines of response (LORs) used for detection and increases as particle separation decreases.

  14. Uncertainties in Air Exchange using Continuous-Injection, Long-Term Sampling Tracer-Gas Methods

    Energy Technology Data Exchange (ETDEWEB)

    Sherman, Max H.; Walker, Iain S.; Lunden, Melissa M.

    2013-12-01

    The PerFluorocarbon Tracer (PFT) method is a low-cost approach commonly used for measuring air exchange in buildings using tracer gases. It is a specific application of the more general Continuous-Injection, Long-Term Sampling (CILTS) method. The technique is widely used but there has been little work on understanding the uncertainties (both precision and bias) associated with its use, particularly given that it is typically deployed by untrained or lightly trained people to minimize experimental costs. In this article we will conduct a first-principles error analysis to estimate the uncertainties and then compare that analysis to CILTS measurements that were over-sampled, through the use of multiple tracers and emitter and sampler distribution patterns, in three houses. We find that the CILTS method can have an overall uncertainty of 10-15percent in ideal circumstances, but that even in highly controlled field experiments done by trained experimenters expected uncertainties are about 20percent. In addition, there are many field conditions (such as open windows) where CILTS is not likely to provide any quantitative data. Even avoiding the worst situations of assumption violations CILTS should be considered as having a something like a ?factor of two? uncertainty for the broad field trials that it is typically used in. We provide guidance on how to deploy CILTS and design the experiment to minimize uncertainties.

  15. Direct inversion of circulation and mixing from tracer measurements - Part 1: Method

    Science.gov (United States)

    von Clarmann, Thomas; Grabowski, Udo

    2016-11-01

    From a series of zonal mean global stratospheric tracer measurements sampled in altitude vs. latitude, circulation and mixing patterns are inferred by the inverse solution of the continuity equation. As a first step, the continuity equation is written as a tendency equation, which is numerically integrated over time to predict a later atmospheric state, i.e., mixing ratio and air density. The integration is formally performed by the multiplication of the initially measured atmospheric state vector by a linear prediction operator. Further, the derivative of the predicted atmospheric state with respect to the wind vector components and mixing coefficients is used to find the most likely wind vector components and mixing coefficients which minimize the residual between the predicted atmospheric state and the later measurement of the atmospheric state. Unless multiple tracers are used, this inversion problem is under-determined, and dispersive behavior of the prediction further destabilizes the inversion. Both these problems are addressed by regularization. For this purpose, a first-order smoothness constraint has been chosen. The usefulness of this method is demonstrated by application to various tracer measurements recorded with the Michelson Interferometer for Passive Atmospheric Sounding (MIPAS). This method aims at a diagnosis of the Brewer-Dobson circulation without involving the concept of the mean age of stratospheric air, and related problems like the stratospheric tape recorder, or intrusions of mesospheric air into the stratosphere.

  16. The Tracer Gas Method of Determining the Charging Efficiency of Two-stroke-cycle Diesel Engines

    Science.gov (United States)

    Schweitzer, P H; Deluca, Frank, Jr

    1942-01-01

    A convenient method has been developed for determining the scavenging efficiency or the charging efficiency of two-stroke-cycle engines. The method consists of introducing a suitable tracer gas into the inlet air of the running engine and measuring chemically its concentration both in the inlet and exhaust gas. Monomethylamine CH(sub 3)NH(sub 2) was found suitable for the purpose as it burns almost completely during combustion, whereas the "short-circuited" portion does not burn at all and can be determined quantitatively in the exhaust. The method was tested both on four-stroke and on two-stroke engines and is considered accurate within 1 percent.

  17. 237 Np analytical method using 239 Np tracers and application to a contaminated nuclear disposal facility

    Energy Technology Data Exchange (ETDEWEB)

    Snow, Mathew S.; Morrison, Samuel S.; Clark, Sue B.; Olson, John E.; Watrous, Matthew G.

    2017-06-01

    Environmental 237Np analyses are challenged by low 237Np concentrations and lack of an available yield tracer; we report a rapid, inexpensive 237Np analytical approach employing the short lived 239Np (t1/2 = 2.3 days) as a chemical yield tracer followed by 237Np quantification using inductively coupled plasma-mass spectrometry. 239Np tracer is obtained via separation from a 243Am stock solution and standardized using gamma spectrometry immediately prior to sample processing. Rapid digestions using a commercial, 900 watt “Walmart” microwave and Parr microwave vessels result in 99.8 ± 0.1% digestion yields, while chromatographic separations enable Np/U separation factors on the order of 106 and total Np yields of 95 ± 4% (2σ). Application of this method to legacy soil samples surrounding a radioactive disposal facility (the Subsurface Disposal Area at Idaho National Laboratory) reveal the presence of low level 237Np contamination within 600 meters of this site, with maximum 237Np concentrations on the order of 103 times greater than nuclear weapons testing fallout levels.

  18. Developement of radioisotope tracer technique; development of verification method for hydraulic model using radioisotope tracer techniques in the municipal wastewater treatment plants

    Energy Technology Data Exchange (ETDEWEB)

    Kim, C. W.; Kim, S. H.; Kim, J. W.; Yun, J. S.; Wo, S. B. [Pusan National University, Pusan (Korea)

    2001-04-01

    This study focuses on the development of the computational fluid dynamics that can be used in secondary clarifier in wastewater treatment plants. This model could describe the internal flow characteristics and predicted similar results as the isotopic tracer experiment. Therefore, it was demonstrated that the isotopic tracer method was a powerful tool as a hydrodynamic model to understand the internal hydraulics. Generally the secondary clarifier can be improved by special design, changing coagulation characteristics by addition of coagulation chemicals and well management by experienced operator. Because of expensive coagulation chemicals and limited availability of experienced operator, the improvement of the design is feasible way to upgrade the secondary clarifier. Though it is very complex and difficult to model the fluid dynamics, CFD model can describe correctly density flow, short circuiting, turbulent dispersion and settling characteristics. There are few trust worthy methods for verifying the hydrodynamic model. Also, it is very difficult to prove the flow by experiment in secondary sedimentation tank because of the disturbing the flow by the experimental equipment. However, the isotope tracer experiment is known as a useful tool for the study of the hydraulic characteristics and floc movement in the sedimentation tank because the isotope tracer does not disturb the internal flow and provide the data quickly through the on-line system. Therefore, the computed fluid dynamic model was developed to make the isotope tracer experiment available as a model verifying method. Predicted results in model simulation were made the same pattern as the experiment on-line data with the time. These results were compared each other. Also, the model explained the detail flow pattern of the area without the monitoring in the sedimentation tank and visualized the internal flow and concentration distribution with time using the graphic software. Because of the complicated

  19. Developement of radioisotope tracer technique; development of verification method for hydraulic model using radioisotope tracer techniques in the municipal wastewater treatment plants

    Energy Technology Data Exchange (ETDEWEB)

    Kim, C. W.; Kim, S. H.; Kim, J. W.; Yun, J. S.; Wo, S. B. [Pusan National University, Pusan (Korea)

    2001-04-01

    This study focuses on the development of the computational fluid dynamics that can be used in secondary clarifier in wastewater treatment plants. This model could describe the internal flow characteristics and predicted similar results as the isotopic tracer experiment. Therefore, it was demonstrated that the isotopic tracer method was a powerful tool as a hydrodynamic model to understand the internal hydraulics. Generally the secondary clarifier can be improved by special design, changing coagulation characteristics by addition of coagulation chemicals and well management by experienced operator. Because of expensive coagulation chemicals and limited availability of experienced operator, the improvement of the design is feasible way to upgrade the secondary clarifier. Though it is very complex and difficult to model the fluid dynamics, CFD model can describe correctly density flow, short circuiting, turbulent dispersion and settling characteristics. There are few trust worthy methods for verifying the hydrodynamic model. Also, it is very difficult to prove the flow by experiment in secondary sedimentation tank because of the disturbing the flow by the experimental equipment. However, the isotope tracer experiment is known as a useful tool for the study of the hydraulic characteristics and floc movement in the sedimentation tank because the isotope tracer does not disturb the internal flow and provide the data quickly through the on-line system. Therefore, the computed fluid dynamic model was developed to make the isotope tracer experiment available as a model verifying method. Predicted results in model simulation were made the same pattern as the experiment on-line data with the time. These results were compared each other. Also, the model explained the detail flow pattern of the area without the monitoring in the sedimentation tank and visualized the internal flow and concentration distribution with time using the graphic software. Because of the complicated

  20. Snowmelt Infiltration Into Alpine Soils Visualised In Situ With A Dye Tracer Method

    Science.gov (United States)

    Stähli, M.; Bayard, D.; Wydler, H.; Flühler, H.

    The mechanisms governing snowmelt infiltration into frozen or unfrozen alpine soils are complex due to the fact that many factors influence the flow paths from the snow pack into the soil, such as soil type, slope inclination and aspect, ground vegetation and the occurrence and persistence of ice on the soil surface or in the frozen soil. Dye tracer experiments are a feasible method to provide a better insight into the real distribution of such water flow paths, which can be very preferential. The main objec- tive of this study was to test the potential of dye tracer methods for visualising in situ snowmelt infiltration at alpine sites and to gain quantitative information on snowmelt infiltration into frozen and unfrozen soils. Field experiments were carried out during winter 2000/01 in southern Switzerland at Hannigalp (2100 m a.s.l.), where a 60 to 80 cm deep Ferric Podzole facing north-west is covered by sparse Ericaceae, and at Gd-St-Bernard pass (2500 m a.s.l.), where a shallow stony Ranker facing south is cov- ered with grass. At the beginning of December a dye tracer (Brilliant Blue FCF) was applied on the soil surface covering an area 5 m downhill x 1.5 m horizontally. At dif- ferent stages during the snowmelt (March to June) we excavated vertical soil profiles on these plots (from below upwards) and took photographs of the stained soil profiles using a digital camera. From these digital images the areas of the soil profiles stained with the dye tracer were determined using a supervised classification method, and the depth distribution of areal coverage of dye tracer was calculated. The water flow pat- tern showed to be extremely heterogeneous in the Hannigalp soil, and more uniform in the Gd-St-Bernard soil. Already in an early stage of the snowmelt we observed infil- tration down to 40 to 60 cm, indicating a relatively high soil matrix infiltration rate at Gd-St-Bernard and efficient preferential flow channels (e.g. along roots) at Hannigalp. Soil frost

  1. Carbon Monoxide Silicate Reduction System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Carbon Monoxide Silicate Reduction System (COSRS) is an innovative method that for the first time uses the strong reductant carbon monoxide to both reduce iron...

  2. Carbon nanotube prepared from carbon monoxide by CVD method and its application as electrode materials

    Institute of Scientific and Technical Information of China (English)

    AN Yuliang; YUAN Xia; CHENG Shinan; GEN Xin

    2006-01-01

    Carbon nanotubes with larger inner diameter were synthesized by the chemical vapor deposition of carbon monoxide (CO) on iron catalyst using H2S as promoting agent.It is found that the structure and morphology of carbon nanotubes can be tailored, to some degree, by varying the experimental conditions such as precursor components and process parameters.The results show that the presence of H2S may play key role for growing Y-branched carbon nanotubes.The products were characterized by SEM, TEM, and Raman spectroscopy, respectively.Furthermore, the obtained carbon nanotubes were explored as electrode materials for supercapacitor.

  3. Are single-well "push-pull" tests suitable tracer methods for aquifer characterization?

    Science.gov (United States)

    Hebig, Klaus; Zeilfelder, Sarah; Ito, Narimitsu; Machida, Isao; Scheytt, Traugott; Marui, Atsunao

    2013-04-01

    Recently, investigations were conducted for geological and hydrogeological characterisation of the sedimentary coastal basin of Horonobe (Hokkaido, Japan). Coastal areas are typical geological settings in Japan, which are less tectonically active than the mountain ranges. In Asia, and especially in Japan, these areas are often densely populated. Therefore, it is important to investigate the behaviour of solutes in such unconsolidated aquifers. In such settings sometimes only single boreholes or groundwater monitoring wells are available for aquifer testing for various reasons, e.g. depths of more than 100 m below ground level and slow groundwater velocities due to density driven flow. A standard tracer test with several involved groundwater monitoring wells is generally very difficult or even not possible at these depths. One of the most important questions in our project was how we can obtain information about chemical and hydraulic properties in such aquifers. Is it possible to characterize solute transport behaviour parameters with only one available groundwater monitoring well or borehole? A so-called "push-pull" test may be one suitable method for aquifer testing with only one available access point. In a push-pull test a known amount of several solutes including a conservative tracer is injected into the aquifer ("push") and afterwards extracted ("pull"). The measured breakthrough curve during the pumping back phase can then be analysed. This method has already been used previously with various aims, also in the recent project (e.g. Hebig et al. 2011, Zeilfelder et al. 2012). However, different test setups produced different tracer breakthrough curves. As no systematic evaluation of this aquifer tracer test method was done so far, nothing is known about its repeatability. Does the injection and extraction rate influence the shape of the breakthrough curve? Which role plays the often applied "chaser", which is used to push the test solution out from the

  4. Continuous and immediate method for the detection of SF/sub 6/ and other tracer gases by electron capture in atmospheric diffusion experiments

    Energy Technology Data Exchange (ETDEWEB)

    Thomsen, E.L. (Aerosol Lab., Risoe, Denmark); Lovelock, J.E.

    1976-01-01

    In many atmospheric diffusion experiments using tracer gases continuous tracer recording is of decisive importance. The main obstacle to continuous electron capture detection of tracer gases in the atmosphere is presented by the oxygen, which is an electron capturer. A method for removing this difficulty is described. Its practical use in an airborne atmospheric plume diffusion experiment is demonstrated.

  5. Quantification of methane emissions from 15 Danish landfills using the mobile tracer dispersion method

    Energy Technology Data Exchange (ETDEWEB)

    Mønster, Jacob [Department of Environmental Engineering, Technical University of Denmark, Miljøvej – Building 113, DK-2800 Lyngby (Denmark); Samuelsson, Jerker, E-mail: jerker.samuelsson@fluxsense.se [Chalmers University of Technology/FluxSense AB, SE-41296 Göteborg (Sweden); Kjeldsen, Peter [Department of Environmental Engineering, Technical University of Denmark, Miljøvej – Building 113, DK-2800 Lyngby (Denmark); Scheutz, Charlotte, E-mail: chas@env.dtu.dk [Department of Environmental Engineering, Technical University of Denmark, Miljøvej – Building 113, DK-2800 Lyngby (Denmark)

    2015-01-15

    Highlights: • Quantification of whole landfill site methane emission at 15 landfills. • Multiple on-site source identification and quantification. • Quantified methane emission from shredder waste and composting. • Large difference between measured and reported methane emissions. - Abstract: Whole-site methane emissions from 15 Danish landfills were assessed using a mobile tracer dispersion method with either Fourier transform infrared spectroscopy (FTIR), using nitrous oxide as a tracer gas, or cavity ring-down spectrometry (CRDS), using acetylene as a tracer gas. The landfills were chosen to represent the different stages of the lifetime of a landfill, including open, active, and closed covered landfills, as well as those with and without gas extraction for utilisation or flaring. Measurements also included landfills with biocover for oxidizing any fugitive methane. Methane emission rates ranged from 2.6 to 60.8 kg h{sup −1}, corresponding to 0.7–13.2 g m{sup −2} d{sup −1}, with the largest emission rates per area coming from landfills with malfunctioning gas extraction systems installed, and the smallest emission rates from landfills closed decades ago and landfills with an engineered biocover installed. Landfills with gas collection and recovery systems had a recovery efficiency of 41–81%. Landfills where shredder waste was deposited showed significant methane emissions, with the largest emission from newly deposited shredder waste. The average methane emission from the landfills was 154 tons y{sup −1}. This average was obtained from a few measurement campaigns conducted at each of the 15 landfills and extrapolating to annual emissions requires more measurements. Assuming that these landfills are representative of the average Danish landfill, the total emission from Danish landfills were calculated at 20,600 tons y{sup −1}, which is significantly lower than the 33,300 tons y{sup −1} estimated for the national greenhouse gas inventory for

  6. A joint velocity-concentration PDF method for tracer flow in heterogeneous porous media

    Science.gov (United States)

    Meyer, Daniel W.; Jenny, Patrick; Tchelepi, Hamdi A.

    2010-12-01

    The probability density function (PDF) of the local concentration of a contaminant, or tracer, is an important component of risk assessment in applications that involve flow in heterogeneous subsurface formations. In this paper, a novel joint velocity-concentration PDF method for tracer flow in highly heterogeneous porous media is introduced. The PDF formalism accounts for advective transport, pore-scale dispersion (PSD), and molecular diffusion. Low-order approximations (LOAs), which are usually obtained using a perturbation expansion, typically lead to Gaussian one-point velocity PDFs. Moreover, LOAs provide reasonable approximations for small log conductivity variances (i.e., σY2 Caroni and Fiorotto (2005) for saturated transport in velocity fields, which are stationary in space and time, for domains with σY2 = 0.05, 1, and 2 and Péclet numbers ranging from 100 to 10,000. PSD is modeled using constant anisotropic dispersion coefficients in both the reference MC computations and our PDF method.

  7. Research of Temperature Tracer Method to Detect Tubular Leakage Passage in Earth-Dam

    Institute of Scientific and Technical Information of China (English)

    WANG Xin-jian; CHEN Jian-sheng

    2006-01-01

    The location, intensity and scope of concentrated leakage must be determined in order to repair earth-Dam scoured by the leakage. In this paper, firstly, heat tracer theory and distribution laws of temperature in soil body with leakage are discussed. Then temperature tracer model is established according to stable heat conduction theory. In such model, the concentrated seepage passage is simplified into a circular pipe as a boundary condition. The location, scope and flow-velocity of the concentrated leakage are estimated via ichnography of the lowest temperature based on temperature data from detecting wells by quantitative computation and qualitative analysis. In case study, the distribution characteristic of temperature (including temperature data of water in reservoir, drainage pipes and tail pond) can be interpreted by this model. A modified model is also set up, applied for detected data at different cross-sections of the leakage passage, in which the temperature data are rectified according to distances from data locations to calculating section. Finally, the model is solved by numerical iterative method, and the possible error of this theoretical model is discussed. The permeability coefficient in leakage area is identical with that of normal soil in magnitude after anti-seepage repairing accomplished, which indicates this model is effective.

  8. [The clinical value of sentinel lymph node detection in laryngeal and hypopharyngeal carcinoma patients with clinically negative neck by methylene blue method and radiolabeled tracer method].

    Science.gov (United States)

    Zhao, Xin; Xiao, Dajiang; Ni, Jianming; Zhu, Guochen; Yuan, Yuan; Xu, Ting; Zhang, Yongsheng

    2014-11-01

    To investigate the clinical value of sentinel lymph node (SLN) detection in laryngeal and hypopharyngeal carcinoma patients with clinically negative neck (cN0) by methylene blue method, radiolabeled tracer method and combination of these two methods. Thirty-three patients with cN0 laryngeal carcinoma and six patients with cN0 hypopharyngeal carcinoma underwent SLN detection using both of methylene blue and radiolabeled tracer method. All these patients were accepted received the injection of radioactive isotope 99 Tc(m)-sulfur colloid (SC) and methylene blue into the carcinoma before surgery, then all these patients underwent intraopertive lymphatic mapping with a handheld gamma-detecting probe and blue-dyed SLN. After the mapping of SLN, selected neck dissections and tumor resections were peformed. The results of SLN detection by radiolabeled tracer, dye and combination of both methods were compared. The detection rate of SLN by radiolabeled tracer, methylene blue and combined method were 89.7%, 79.5%, 92.3% respectively. The number of detected SLN was significantly different between radiolabeled tracer method and combined method, and also between methylene blue method and combined method. The detection rate of methylene blue and radiolabeled tracer method were significantly different from combined method (P methylene blue can improve the detection rate and accuracy of sentinel lymph node detection. Furthermore, sentinel lymph node detection can accurately represent the cervical lymph node status in cN0 laryngeal and hypopharyngeal carcinoma.

  9. Dual-tracer method to estimate coral reef response to a plume of chemically modified seawater

    Science.gov (United States)

    Maclaren, J. K.; Caldeira, K.

    2013-12-01

    We present a new method, based on measurement of seawater samples, to estimate the response of a reef ecosystem to a plume of an additive (for example, a nutrient or other chemical). In the natural environment, where there may be natural variability in concentrations, it can be difficult to distinguish between changes in concentrations that would occur naturally and changes in concentrations that result from a chemical addition. Furthermore, in the unconfined natural environment, chemically modified water can mix with waters that have not been modified, making it difficult to distinguish between effects of dilution and effects of chemical fluxes or transformations. We present a dual-tracer method that extracts signals from observations that may be affected by both natural variability and dilution. In this dual-tracer method, a substance (in our example case, alkalinity) is added to the water in known proportion to a passive conservative tracer (in our example case, Rhodamine WT dye). The resulting plume of seawater is allowed to flow over the study site. Two transects are drawn across the plume at the front and back of the study site. If, in our example, alkalinity is plotted as a function of dye concentration for the front transect, the slope of the resulting mixing line is the ratio of alkalinity to dye in the added fluid. If a similar mixing line is measured and calculated for the back transect, the slope of this mixing line will indicate the amount of added alkalinity that remains in the water flowing out of the study site per unit of added dye. The ratio of the front and back slopes indicates the fraction of added alkalinity that was taken up by the reef. The method is demonstrated in an experiment performed on One Tree Reef (Queensland, Australia) aimed at showing that ocean acidification is already affecting coral reef growth. In an effort to chemically reverse some of the changes to seawater chemistry that have occurred over the past 200 years, we added

  10. A Study on sediment sources in a small watershed by using REE tracer method

    Institute of Scientific and Technical Information of China (English)

    石辉; 田均良; 刘普灵; 周佩华

    1997-01-01

    In simulation experiments, rare earth element (REE) tracer method was first used to sludy the sources of sediment yield in a small watershed. The experimental results have shown that the chief parts of sediment sources are constantly changing with the development of gullies. The cutting erosion plays a major role in the primary stage of watershed development. Slope erosion intensity increased gradually with gully development of the watershed, while gully erosion intensity decreased. Similar process was also observed in an individual rainfall. The simulation experiments have shown that the method can satisfactorily interpret the origins of sediment yield of a small watershed on an effective way. The simulation experiments have also provided basic information for field researches.

  11. Study of organic N transformation in red soils by 15N tracer method

    Institute of Scientific and Technical Information of China (English)

    YeQing-Fu; ZhangQin-Zheng; 等

    1997-01-01

    Uniformly 15N-labelled ryegrass was used to investigate NH4+-production,microbial transformation and humification of organic N in two types of red soils by incubating the soils amended with labelled material.The results showed that there was little significant difference in biomass N transformation in the tested solis between 15N tracer method and conventional method,but the amount of NH4++-N released form the ryegrass in the clayey soil than in the sandy soil at all sampling time .By 120d of incubation,humified N was less than 10% of the amount of the applied N in two types of red soils and the amount of residual N in the clayey red soil was obviously higher than that in the sandy red soil.

  12. A method to investigate inter-aquifer leakage using hydraulics and multiple environmental tracers

    Science.gov (United States)

    Priestley, Stacey; Love, Andrew; Wohling, Daniel; Post, Vincent; Shand, Paul; Kipfer, Rolf; Tyroller, Lina

    2016-04-01

    Informed aquifer management decisions regarding sustainable yields or potential exploitation require an understanding of the groundwater system (Alley et al. 2002, Cherry and Parker 2004). Recently, the increase in coal seam gas (CSG) or shale gas production has highlighted the need for a better understanding of inter-aquifer leakage and contaminant migration. In most groundwater systems, the quantity or location of inter-aquifer leakage is unknown. Not taking into account leakage rates in the analysis of large scale flow systems can also lead to significant errors in the estimates of groundwater flow rates in aquifers (Love et al. 1993, Toth 2009). There is an urgent need for robust methods to investigate inter-aquifer leakage at a regional scale. This study builds on previous groundwater flow and inter-aquifer leakage studies to provide a methodology to investigate inter-aquifer leakage in a regional sedimentary basin using hydraulics and a multi-tracer approach. The methodology incorporates geological, hydrogeological and hydrochemical information in the basin to determine the likelihood and location of inter-aquifer leakage. Of particular benefit is the analysis of hydraulic heads and environmental tracers at nested piezometers, or where these are unavailable bore couplets comprising bores above and below the aquitard of interest within a localised geographical area. The proposed methodology has been successful in investigating inter-aquifer leakage in the Arckaringa Basin, South Australia. The suite of environmental tracers and isotopes used to analyse inter-aquifer leakage included the stable isotopes of water, radiocarbon, chloride-36, 87Sr/86Sr and helium isotopes. There is evidence for inter-aquifer leakage in the centre of the basin ~40 km along the regional flow path. This inter-aquifer leakage has been identified by a slight draw-down in the upper aquifer during pumping in the lower aquifer, overlap in Sr isotopes, δ2H, δ18O and chloride

  13. Tracer methods for investigating biosynthetic pathways and the metabolism of bioactive substances in plants. [Herbicides; Plant growth regulators

    Energy Technology Data Exchange (ETDEWEB)

    Schuette, H.R. (Akademie der Wissenschaften der DDR, Halle/Saale. Inst. fuer Biochemie der Pflanzen)

    1984-03-01

    Proceeding from the general terms of investigating the courses of reactions in plants by means of tracer methods, problems and possibilities of the methods are discussed on the basis of examples referring in particular to double labelling techniques and to the determination of the distribution of radioactivity in the resulting products. Examples of herbicides and plant growth regulators are used for describing metabolism studies.

  14. Tracer Gas Technique Versus a Control Box Method for Estimating Direct Capture Efficiency of Exhaust Systems

    DEFF Research Database (Denmark)

    Madsen, U.; Aubertin, G.; Breum, N. O.;

    Numerical modelling of direct capture efficiency of a local exhaust is used to compare the tracer gas technique of a proposed CEN standard against a more consistent approach based on an imaginary control box. It is concluded that the tracer gas technique is useful for field applications....

  15. Evaluation of the transport matrix method for simulation of ocean biogeochemical tracers

    Science.gov (United States)

    Kvale, Karin F.; Khatiwala, Samar; Dietze, Heiner; Kriest, Iris; Oschlies, Andreas

    2017-06-01

    Conventional integration of Earth system and ocean models can accrue considerable computational expenses, particularly for marine biogeochemical applications. Offline numerical schemes in which only the biogeochemical tracers are time stepped and transported using a pre-computed circulation field can substantially reduce the burden and are thus an attractive alternative. One such scheme is the transport matrix method (TMM), which represents tracer transport as a sequence of sparse matrix-vector products that can be performed efficiently on distributed-memory computers. While the TMM has been used for a variety of geochemical and biogeochemical studies, to date the resulting solutions have not been comprehensively assessed against their online counterparts. Here, we present a detailed comparison of the two. It is based on simulations of the state-of-the-art biogeochemical sub-model embedded within the widely used coarse-resolution University of Victoria Earth System Climate Model (UVic ESCM). The default, non-linear advection scheme was first replaced with a linear, third-order upwind-biased advection scheme to satisfy the linearity requirement of the TMM. Transport matrices were extracted from an equilibrium run of the physical model and subsequently used to integrate the biogeochemical model offline to equilibrium. The identical biogeochemical model was also run online. Our simulations show that offline integration introduces some bias to biogeochemical quantities through the omission of the polar filtering used in UVic ESCM and in the offline application of time-dependent forcing fields, with high latitudes showing the largest differences with respect to the online model. Differences in other regions and in the seasonality of nutrients and phytoplankton distributions are found to be relatively minor, giving confidence that the TMM is a reliable tool for offline integration of complex biogeochemical models. Moreover, while UVic ESCM is a serial code, the TMM can

  16. Ice-affected streamflow records using tracer-dilution discharge methods

    Science.gov (United States)

    Capesius, J.P.; Sullivan, J.R.; Williams, C.A.; O'Neill, G. B.; ,

    2002-01-01

    Accurate ice-affected streamflow records are difficult to obtain for several reasons. Problems measuring stage, variable backwater conditions, access limitations in wintertime, and problems measuring flowing water under ice cover all contribute to make ice-affected streamflow records less accurate than open-channel streamflow records. The inaccuracy of ice-affected streamflow records is particularly troublesome for small streams where Instream-Flow water rights exist. The Colorado Water Conservation Board uses these water rights to protect in-stream aquatic communities. In January and February 2002, the U.S. Geological Survey, in cooperation with the Colorado Water Conservation Board, conducted an experiment using a sodium chloride tracer to determine streamflow under ice cover. The purpose of this study is to determine the usefulness and accuracy of ice-affected streamflow records using a sodium chloride tracer that was automatically injected into the stream. The tracer was injected at two gaging stations once per day for up to 25 days. Multiple-parameter water-quality sensors at the two gaging stations monitored background and peak tracer concentrations and conductance. These data were used to determine discharge at each site. A comparison of current-meter measurements to tracer-dilution discharge measurements shows an underestimation of discharge due to inaccuracy of current-meter measurements with ice cover and inconsistent tracer-pump rates caused by partial freezing of the tracer solution in the injection lines.

  17. Characterization of a cryogenic distillation column with a Kr-83m tracer method

    Energy Technology Data Exchange (ETDEWEB)

    Rosendahl, Stephan; Fieguth, Alexander; Huhmann, Chrisian; Murra, Michael; Weinheimer, Christian [Institut fuer Kernphysik, Wilhelm-Klemm Strasse 9, 48149 Muenster (Germany); Cristescu, Ion [Karlsruher Institut fuer Technologie, Tritium Laboratory, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany)

    2016-07-01

    The XENON1T experiment aims for the direct detection of dark matter with unreached precision of 2 x 10{sup -47} cm{sup 2} for the spin-independent WIMP-nucleon cross section. The cryogenic distillation is an important tool to reduce the intrinsic contamination with radioactive {sup 85}Kr which undergoes a beta-decay with an endpoint energy of 687 keV, being one major source of background. Hence, a novel cryogenic distillation column has been designed and constructed in order to reduce the krypton concentration to {sup nat}Kr/Xe<0.2 ppt. For the investigation of the performance and the dynamics of the distillation process on the sub-ppt level, a new {sup 83m}Kr tracer method has been applied. For the {sup 83m}Kr detection custom made PMT based detectors are used. In this talk the method as well as the results of the studies of the krypton separation are presented.

  18. Pre-fire warning system and method using a perfluorocarbon tracer

    Science.gov (United States)

    Dietz, Russell N.; Senum, Gunnar I.

    1994-01-01

    A composition and method for detecting thermal overheating of an apparatus or system and for quickly and accurately locating the portions of the apparatus or system that experience a predetermined degree of such overheating. A composition made according to the invention includes perfluorocarbon tracers (PFTs) mixed with certain non-reactive carrier compounds that are effective to trap or block the PFTs within the composition at normal room temperature or at normal operating temperature of the coated apparatus or system. When a predetermined degree of overheating occurs in any of the coated components of the apparatus or system, PFTs are emitted from the compositions at a rate corresponding to the degree of overheating of the component. An associated PFT detector (or detectors) is provided and monitored to quickly identify the type of PFTs emitted so that the PFTs can be correlated with the respective PFT in the coating compositions applied on respective components in the system, thereby to quickly and accurately localize the source of the overheating of such components.

  19. Greenhouse gas emission quantification from wastewater treatment plants, using a tracer gas dispersion method

    DEFF Research Database (Denmark)

    Delre, Antonio; Mønster, Jacob; Scheutz, Charlotte

    2017-01-01

    Plant-integrated methane (CH4) and nitrous oxide (N2O) emission quantifications were performed at five Scandinavian wastewater treatment plants, using a ground-based remote sensing approach that combines a controlled release of tracer gas from the plant with downwind concentration measurements. C...

  20. Carbon monoxide poisoning

    Science.gov (United States)

    ... and smokers. Carbon monoxide can harm a fetus (unborn baby still in the womb). Symptoms of carbon ... symptoms Outlook (Prognosis) Carbon monoxide poisoning can cause death. For those who survive, recovery is slow. How ...

  1. Local study of pollutants dispersion by a real time tracer method; Etude locale de la dispersion de polluants par une methode de tracage en temps reel

    Energy Technology Data Exchange (ETDEWEB)

    Faivre-Pierret, R.X.; Sestier-Carlin, R.; Berne, P.

    1992-12-31

    It is possible to use a Gaussian mathematical model of atmospheric dispersion for calculating atmospheric transfer coefficient (ATC) in long range model, but for proximity models, an experimental model using a tracer technic has to take in account ground effects and natural or artificial obstacles. SF{sub 6} tracer method gives the true plume ground trace in real time. The measured ATC shows a larger ground trace, lower concentration in the axis, and a displacement of the maximum concentration with regard to wind axis in comparison with the calculated ATC. (A.B.). 14 refs., 4 figs., 1 tab.

  2. CARBON MONOXIDE TREATMENT GUIDELINES

    Directory of Open Access Journals (Sweden)

    Miran Brvar

    2014-02-01

    Full Text Available Carbon monoxide is the leading cause of unintentional poisoning-related death in Slovenia. It is an odorless, colorless gas that usually remains undetectable until exposures result in injury or death. Exposure to carbon monoxide is most commonly accompanied by headache, nausea, vomiting, dizziness, confusion, drowsiness, fatigue and collapse. Carbon monoxide poisoning management includes normobaric oxygen therapy. Hyperbaric-oxygen treatments reduce the risk of cognitive sequelae after carbon monoxide poisoning. 

  3. Uniform silica coated fluorescent nanoparticles: synthetic method, improved light stability and application to visualize lymph network tracer.

    Directory of Open Access Journals (Sweden)

    Liman Cong

    Full Text Available BACKGROUND: The sentinel lymph node biopsy (SLNB was developed as a new modality in the surgical diagnosis of lymph node metastases. Dye and radioisotope are major tracers for the detection of sentinel lymph nodes (SLN. Dye tends to excessively infiltrate into the interstitium due to their small size (less than several nanometers, resulting in difficulties in maintaining clear surgical fields. Radioisotopes are available in limited number of hospitals. Fluorescent nanoparticles are good candidates for SLN tracer to solve these problems, as we can choose suitable particle size and fluorescence wavelength of near-infrared. However, the use of nanoparticles faces safety issues, and many attempts have been performed by giving insulating coats on nanoparticles. In addition, the preparation of the uniform insulating layer is important to decrease variations in the quality as an SLN tracer. METHODOLOGY/PRINCIPAL FINDINGS: We herein succeeded in coating fluorescent polystyrene nanoparticles of 40 nm with uniform silica layer of 13 nm by the modified Stöber method. The light stability of silica coated nanoparticles was 1.3-fold greater than noncoated nanoparticles. The popliteal lymph node could be visualized by the silica coated nanoparticles with injection in the rat feet. CONCLUSIONS/SIGNIFICANCE: The silica coated nanoparticles in lymph nodes could be observed by transmission electron microscope, suggesting that our silica coating method is useful as a SLN tracer with highly precise distribution of nanoparticles in histological evaluation. We also demonstrated for the first time that a prolonged enhancement of SLN is caused by the phagocytosis of fluorescent nanoparticles by both macrophages and dendritic cells.

  4. Carbon Monoxide Information Center

    Medline Plus

    Full Text Available ... main content Languages 简体中文 English Bahasa Indonesia 한국어 Español ภาษาไทย Tiếng Việt Text Size: Decrease Font Increase ... Monoxide Information Center Carbon Monoxide Information Center En Español The Invisible Killer Carbon monoxide, also known as ...

  5. Method for assessment of stormwater treatment facilities – Synthetic road runoff addition including micro-pollutants and tracer

    DEFF Research Database (Denmark)

    Cederkvist, Karin; Jensen, Marina Bergen; Holm, Peter Engelund

    2017-01-01

    representative of runoff from roads is suggested, as well as relevant concentration ranges. The method was used for adding contaminants to three different STFs including a curbstone extension with filter soil, a dual porosity filter, and six different permeable pavements. Evaluation of the method showed......% in the dual porosity filter, stressing the importance of including a conservative tracer for correction of contaminant retention values. The method is considered useful in future treatment performance testing of STFs. The observed performance of the STFs is presented in coming papers....

  6. Modified Perfluorocarbon Tracer Method for Measuring Effective Multizone Air Exchange Rates

    Directory of Open Access Journals (Sweden)

    Masashi Gamo

    2010-08-01

    Full Text Available A modified procedure was developed for the measurement of the effective air exchange rate, which represents the relationship between the pollutants emitted from indoor sources and the residents’ level of exposure, by placing the dosers of tracer gas at locations that resemble indoor emission sources. To measure the 24-h-average effective air exchange rates in future surveys based on this procedure, a low-cost, easy-to-use perfluorocarbon tracer (PFT doser with a stable dosing rate was developed by using double glass vials, a needle, a polyethylene-sintered filter, and a diffusion tube. Carbon molecular sieve cartridges and carbon disulfide (CS2 were used for passive sampling and extraction of the tracer gas, respectively. Recovery efficiencies, sampling rates, and lower detection limits for 24-h sampling of hexafluorobenzene, octafluorotoluene, and perfluoroallylbenzene were 40% ± 3%, 72% ± 5%, and 84% ± 6%; 10.5 ± 1.1, 14.4 ± 1.4, and 12.2 ± 0.49 mL min−1; and 0.20, 0.17, and 0.26 μg m–3, respectively.

  7. Measuring In-Cabin School Bus Tailpipe and Crankcase PM2.5: A New Dual Tracer Method.

    Science.gov (United States)

    Ireson, Robert G; Ondov, John M; Zielinska, Barbara; Weaver, Christopher S; Easter, Michael D; Lawson, Douglas R; Hesterberg, Thomas W; Davey, Mark E; Liu, L-J Sally

    2011-05-01

    Exposures of occupants in school buses to on-road vehicle emissions, including emissions from the bus itself, can be substantially greater than those in outdoor settings. A dual tracer method was developed and applied to two school buses in Seattle in 2005 to quantify in-cabin fine particulate matter (PM2.5) concentrations attributable to the buses' diesel engine tailpipe (DPMtp) and crankcase vent (PMck) emissions. The new method avoids the problem of differentiating bus emissions from chemically identical emissions of other vehicles by using a fuel-based organometallic iridium tracer for engine exhaust and by adding deuterated hexatriacontane to engine oil. Source testing results showed consistent PM:tracer ratios for the primary tracer for each type of emissions. Comparisons of the PM:tracer ratios indicated that there was a small amount of unburned lubricating oil emitted from the tailpipe; however, virtually no diesel fuel combustion products were found in the crankcase emissions. For the limited testing conducted here, although PMck emission rates (averages of 0.028 and 0.099 g/km for the two buses) were lower than those from the tailpipe (0.18 and 0.14 g/km), in-cabin PMck concentrations averaging 6.8 μg/m(3) were higher than DPMtp (0.91 μg/m(3) average). In-cabin DPMtp and PMck concentrations were significantly higher with bus windows closed (1.4 and 12 μg/m(3), respectively) as compared with open (0.44 and 1.3 μg/m(3), respectively). For comparison, average closed- and open-window in-cabin total PM2.5 concentrations were 26 and 12 μg/m(3), respectively. Despite the relatively short in-cabin sampling times, very high sensitivities were achieved, with detection limits of 0.002 μg/m(3) for DPMtp and 0.05 μg/m(3) for PMck. [Box: see text].

  8. Integration of Tracer Test Data to Refine Geostatistical Hydraulic Conductivity Fields Using Sequential Self-Calibration Method

    Institute of Scientific and Technical Information of China (English)

    Bill X Hu; Jiang Xiaowei; Wan Li

    2007-01-01

    On the basis of local measurements of hydraulic conductivity, geostatistical methods have been found to be useful in heterogeneity characterization of a hydraulic conductivity field on a regional scale. However, the methods are not suited to directly integrate dynamic production data, such as,hydraulic head and solute concentration, into the study of conductivity distribution. These data, which record the flow and transport processes in the medium, are closely related to the spatial distribution of hydraulic conductivity. In this study, a three-dimensional gradient-based inverse method-the sequential self-calibration (SSC) method-is developed to calibrate a hydraulic conductivity field,initially generated by a geostatistical simulation method, conditioned on tracer test results. The SSC method can honor both local hydraulic conductivity measurements and tracer test data. The mismatch between the simulated hydraulic conductivity field and the reference true one, measured by its mean square error (MSE), is reduced through the SSC conditional study. In comparison with the unconditional results, the SSC conditional study creates the mean breakthrough curve much closer to the reference true curve, and significantly reduces the prediction uncertainty of the solute transport in the observed locations. Further, the reduction of uncertainty is spatially dependent, which indicates that good locations, geological structure, and boundary conditions will affect the efficiency of the SSC study results.

  9. Molten metal reactor and method of forming hydrogen, carbon monoxide and carbon dioxide using the molten alkaline metal reactor

    Science.gov (United States)

    Bingham, Dennis N.; Klingler, Kerry M.; Turner, Terry D.; Wilding, Bruce M.

    2012-11-13

    A molten metal reactor for converting a carbon material and steam into a gas comprising hydrogen, carbon monoxide, and carbon dioxide is disclosed. The reactor includes an interior crucible having a portion contained within an exterior crucible. The interior crucible includes an inlet and an outlet; the outlet leads to the exterior crucible and may comprise a diffuser. The exterior crucible may contain a molten alkaline metal compound. Contained between the exterior crucible and the interior crucible is at least one baffle.

  10. Study on Transfer of Ni in Soil—Plant System Using 63Ni Tracer Method

    Institute of Scientific and Technical Information of China (English)

    TUCONG

    1996-01-01

    A study was carried out on the transfer of native and added Ni towards plant both in different soils and at different time by using 63 Ni tracer technique.The transfer of added Ni in soil was greater than native Ni and declined as time increased.The mobility was greater for soluble plus exchangeable fraction of soil Ni but very smaller for residual and Fe/Mn oxide bound fractions.These indicated that Ni was more mobile and more harmful in soils with a low pH and /or low content of Fe/Mn oxides.

  11. Environmental Tracers

    Directory of Open Access Journals (Sweden)

    Trevor Elliot

    2014-10-01

    Full Text Available Environmental tracers continue to provide an important tool for understanding the source, flow and mixing dynamics of water resource systems through their imprint on the system or their sensitivity to alteration within it. However, 60 years or so after the first isotopic tracer studies were applied to hydrology, the use of isotopes and other environmental tracers are still not routinely necessarily applied in hydrogeological and water resources investigations where appropriate. There is therefore a continuing need to promote their use for developing sustainable management policies for the protection of water resources and the aquatic environment. This Special Issue focuses on the robustness or fitness-for-purpose of the application and use of environmental tracers in addressing problems and opportunities scientifically, to promote their wider use and to address substantive issues of vulnerability, sustainability, and uncertainty in (groundwater resources systems and their management.

  12. Catalytic Oxidation of Propylene, Toluene, Carbon Monoxide, and Carbon Black over Au/CeO2 Solids: Comparing the Impregnation and the Deposition-Precipitation Methods

    Directory of Open Access Journals (Sweden)

    Antoine Aboukaïs

    2013-01-01

    Full Text Available Au/CeO2 solids were prepared by two methods: deposition-precipitation (DP and impregnation (Imp. The prepared solids were calcined under air at 400°C. Both types of catalysts have been tested in the total oxidation of propylene, toluene, carbon monoxide, and carbon black. Au/CeO2-DP solids were the most reactive owing to the high number of gold nanoparticles and Au+ species and the low concentration of Cl- ions present on its surface compared to those observed in Au/CeO2-Imp solids.

  13. A Novel Method For Predicting Carbon Monoxide Apparent Quantum Yield Spectra in Coastal Water Using Remote Sensing Reflectance Data

    Science.gov (United States)

    Reader, H. E.; Miller, W. L.

    2010-12-01

    Photochemical oxidation of chromophoric dissolved organic matter (CDOM) is the major source of carbon monoxide to the surface ocean. Bacterial consumption and air-sea exchange comprise the two known sinks for CO in marine systems. Though the two loss terms are relatively efficient, CO remains supersaturated with respect to the atmosphere in the surface ocean. Global oceanic estimates of CO photoproduction range from 30-84Tg CO/year (Zafiriou 2003, Fichot and Miller 2010). The variation in estimates is largely due to the difficulty in predicting the efficiency of photoproduction (i.e. Apparent Quantum Yield; AQY). Though the AQY for CO photoproduction appears to be relatively constant, there is indication that terrestrially derived sources, such as those found in estuarine environments, produce CO more efficiently than marine derived sources (Ziolkowski 2000). Since variation among sources is likely in the global ocean, accurate assignment of AQY to variable water types is required to accurately predict CO photoproduction. Deriving the correct apparent quantum yield from remotely sensed data would lead to better predictions of large scale CO photoproduction from optical data. Thirty-eight (38) AQY spectra for CO photoproduction were determined by monthly sampling during spring tides in three dark water locations on the coast of Georgia, USA, from November 2008 to September 2009. Sapelo Sound, a marine dominated system, receives little to no freshwater input over the year, while Altamaha Sound drains the largest watershed in the state of Georgia, and has largely variably freshwater input. Doboy Sound, situated between Sapelo Sound and Altamaha Sound, is largely marine dominated, though in periods of high flow on the Altamaha River, receives some fresh water overflow. The coast of Georgia is dominated by Spartina alterniflora salt marshes, and thus also has a strong non-point source of terrestrially derived carbon. CO apparent quantum yields were determined by

  14. Journal: Efficient Hydrologic Tracer-Test Design for Tracer ...

    Science.gov (United States)

    Hydrological tracer testing is the most reliable diagnostic technique available for the determination of basic hydraulic and geometric parameters necessary for establishing operative solute-transport processes. Tracer-test design can be difficult because of a lack of prior knowledge of the basic hydraulic and geometric parameters desired and the appropriate tracer mass to release. A new efficient hydrologic tracer-test design (EHTD) methodology has been developed to facilitate the design of tracer tests by root determination of the one-dimensional advection-dispersion equation (ADE) using a preset average tracer concentration which provides a theoretical basis for an estimate of necessary tracer mass. The method uses basic measured field parameters (e.g., discharge, distance, cross-sectional area) that are combined in functional relatipnships that descrive solute-transport processes related to flow velocity and time of travel. These initial estimates for time of travel and velocity are then applied to a hypothetical continuous stirred tank reactor (CSTR) as an analog for the hydrological-flow system to develop initial estimates for tracer concentration, tracer mass, and axial dispersion. Application of the predicted tracer mass with the hydraulic and geometric parameters in the ADE allows for an approximation of initial sample-collection time and subsequent sample-collection frequency where a maximum of 65 samples were determined to be necessary for descri

  15. Carbon Monoxide Information Center

    Medline Plus

    Full Text Available ... Estimates OCTOBER 13, 2015 Incidents, Deaths, and In-Depth Investigations Associated with Non-Fire Carbon Monoxide from Engine-Driven Generators and ... Engine-Driven Tools, 2004–2014 JANUARY 08, 2015 Non-Fire Carbon Monoxide Deaths Associated with the Use of Consumer Products 2011 Annual Estimates View All ... Inside CPSC Accessibility ...

  16. Engineering evidence for carbon monoxide toxicity cases.

    Science.gov (United States)

    Galatsis, Kosmas

    2016-07-01

    Unintentional carbon monoxide poisonings and fatalities lead to many toxicity cases. Given the unusual physical properties of carbon monoxide-in that the gas is odorless and invisible-unorganized and erroneous methods in obtaining engineering evidence as required during the discovery process often occurs. Such evidence gathering spans domains that include building construction, appliance installation, industrial hygiene, mechanical engineering, combustion and physics. In this paper, we attempt to place a systematic framework that is relevant to key aspects in engineering evidence gathering for unintentional carbon monoxide poisoning cases. Such a framework aims to increase awareness of this process and relevant issues to help guide legal counsel and expert witnesses.

  17. Groundwater discharge dynamics from point to catchment scale in a lowland stream: Combining hydraulic and tracer methods

    DEFF Research Database (Denmark)

    Poulsen, Jane Bang; Sebok, Eva; Duque, Carlos

    2015-01-01

    nutrient or pollutant transport zones from nearby agricultural fields. VTP measurements confirmed high groundwater fluxes in discharge areas indicated by DTS and ADCP, and this coupling of ADCP, DTS and VTP proposes a novel field methodology to detect areas of concentrated groundwater discharge with higher......Detecting, quantifying and understanding groundwater discharge to streams are crucial for the assessment of water, nutrient and contaminant exchange at the groundwater–surface water interface. In lowland agricultural catchments with significant groundwater discharge this is of particular importance...... because of the risk of excess leaching of nutrients to streams. Here we aim to combine hydraulic and tracer methods from point-to-catchment scale to assess the temporal and spatial variability of groundwater discharge in a lowland, groundwater gaining stream in Denmark. At the point-scale, groundwater...

  18. 卷烟烟气中一氧化碳的简易测试方法%A simple method for carbon monoxide testing in the cigarette smoke

    Institute of Scientific and Technical Information of China (English)

    王兆东; 胡秀峰; 霍晓晖; 王玉林; 李占臣; 韦丽红; 康晓鸥; 崔立娟

    2013-01-01

    为了降低烟气中CO吸附材料的筛选成本,组装了一套烟气采集装置,该装置能够直接采集点燃卷烟的烟气,也能采集经过吸附材料后的烟气.对所采集烟气的CO体积分数进行检测,考察吸附材料或添加剂吸附CO的效果.结果表明,该装置适宜的采样时间为烟支燃烧后3~5 min,所需吸附材料仅约1 g,所需测试时间为50 min,具有组装容易、操作简单和价格低廉的特点.但因为采集烟气的针孔有泄露,再加上手工操作导致不确定性,该方法仅适用于定性筛选吸附材料或添加剂.%This article is aimed to present an easy and practical method for testing carbon monoxide in the cigarette smoke.First of all,we have collected the cigarette smoke sample by using a smoke sample assembling device.The sample can be collected directly by lighting a cigarette in the device in a time length of about 3-5 min after the cigarette was lit up.Then,we can study the CO-adsorbed features of the adsorbed material by comparing the results of carbon monoxide testing in the smoke sample.A test can thus be finished with the adsorbing material 1 g or so in 50 minutes at a time.The method we have worked out is characterized by its easy assembling,low price and simple operation.The application results of the experiment with the method demonstrate that it can improve the smoke sample preparation and processing line of the absorbing material or addifives greatly due to producing less reaction products.The advantages of the method also lie in its screening of the absorbing materials or additives qualitatively,for the smoke leakage occurred just through a small pinhole when the sample is collected by using a syringe and for the particular uncertainty manually.In order to reduce the cost of research and development to screen adsorption material for adsorbing the carbon monoxide,the method we have worked out is simple in application,convenient in collecting the testing sample and testing

  19. Synthesis of Nanosized Zinc-Doped Cobalt Oxyhydroxide Parties by a Dropping Method and Their Carbon Monoxide Gas Sensing Properties

    Directory of Open Access Journals (Sweden)

    Jian-Wen Wang

    2013-01-01

    Full Text Available Two nanostructures of cobalt oxyhydroxide (CoOOH and Zinc-(Zn- doped CoOOH (1–4% Zn are prepared from Co(NO32 solution via microtitration with NaOH and oxidation in air. The X-ray diffraction (XRD analysis results show that a pure state of nano-CoOOH can be obtained at an alkalinity (OH−/Co+ of 5 with 40°C heat treatment after 6 h. The Zn ions preferentially substitute Co ions in the CoOOH structure, resulting in a decrease of its crystallinity. The disc-like CoOOH nanostructure exhibits good sensitivity to carbon monoxide (CO in a temperature range of 40–110°C with maximum sensitivity to CO at around 70–80°C. When CoOOH nanostructure is doped with 1% Zn, its sensitivity and selectivity for CO gas are improved at 70–80°C; further Zn doping to 2% degraded the CO sensing properties of nano-CoOOH. The results of a cross-sensitivity investigation of the sensor to various gases coexisting at early stages of a fire show that the sensitivity of Zn-doped nano-CoOOH is the highest toward CO. Zn-doped nano-CoOOH film exhibits a high sensitivity to CO at room temperature, making it a promising sensor for early-stage fire detection.

  20. Numerical evaluation of the PERTH (PERiodic Tracer Hierarchy) method for estimating time-variable travel time distribution in variably saturated soils

    Science.gov (United States)

    Kim, M.; Harman, C. J.

    2013-12-01

    The distribution of water travel times is one of the crucial hydrologic characteristics of the catchment. Recently, it has been argued that a rigorous treatment of travel time distributions should allow for their variability in time because of the variable fluxes and partitioning of water in the water balance, and the consequent variable storage of a catchment. We would like to be able to observe the structure of the temporal variations in travel time distributions under controlled conditions, such as in a soil column or under irrigation experiments. However, time-variable travel time distributions are difficult to observe using typical active and passive tracer approaches. Time-variability implies that tracers introduced at different times will have different travel time distributions. The distribution may also vary during injection periods. Moreover, repeat application of a single tracer in a system with significant memory leads to overprinting of break-through curves, which makes it difficult to extract the original break-through curves, and the number of ideal tracers that can be applied is usually limited. Recognizing these difficulties, the PERTH (PERiodic Tracer Hierarchy) method has been developed. The method provides a way to estimate time-variable travel time distributions by tracer experiments under controlled conditions by employing a multi-tracer hierarchy under periodical hydrologic forcing inputs. The key assumption of the PERTH method is that as time gets sufficiently large relative to injection time, the average travel time distribution of two distinct ideal tracers injected during overlapping periods become approximately equal. Thus one can be used as a proxy for the other, and the breakthrough curves of tracers applied at different times in a periodic forcing condition can be separated from one another. In this study, we tested the PERTH method numerically for the case of infiltration at the plot scale using HYDRUS-1D and a particle

  1. Carbon Monoxide Information Center

    Medline Plus

    Full Text Available ... CONSUMER PRODUCT SAFETY COMMISSION Search CPSC Search Menu Home Recalls Recall List CPSC Recall API Recall Lawsuits ... and Bans Report an Unsafe Product Consumers Businesses Home Safety Education Safety Education Centers Carbon Monoxide Information ...

  2. Carbon Monoxide Information Center

    Medline Plus

    Full Text Available ... Safety Blogs: CO Safety More CO Blogs Research & Statistics JANUARY 07, 2016 Non-Fire Carbon Monoxide Deaths ... 2011 Annual Estimates View All CO-Related Injury Statistics and Technical Reports Related Links Recalls Safety Education ...

  3. Carbon Monoxide Information Center

    Medline Plus

    Full Text Available ... On Safety Blogs: CO Safety More CO Blogs Research & Statistics JANUARY 07, 2016 Non-Fire Carbon Monoxide ... Related Links Recalls Safety Education Regulations, Laws & Standards Research & Statistics Business & Manufacturing Small Business Resources OnSafety Blogs ...

  4. Carbon Monoxide Information Center

    Medline Plus

    Full Text Available ... Community Outreach Resource Center Toy Recall Statistics CO Poster Contest Pool Safely Business & Manufacturing Business & Manufacturing Business ... Featured Resources CPSC announces winners of carbon monoxide poster contest Video View the blog Clues You Can ...

  5. Carbon Monoxide Information Center

    Science.gov (United States)

    ... and Criminal Penalties Federal Court Orders & Decisions Research & Statistics Research & Statistics Technical Reports Injury Statistics NEISS Injury Data ... On Safety Blogs: CO Safety More CO Blogs Research & Statistics JANUARY 07, 2016 Non-Fire Carbon Monoxide Deaths ...

  6. Carbon Monoxide Information Center

    Medline Plus

    Full Text Available ... Statistics JANUARY 07, 2016 Non-Fire Carbon Monoxide Deaths Associated with the Use of Consumer Products 2012 Annual Estimates OCTOBER 13, 2015 Incidents, Deaths, and In-Depth Investigations Associated with Non-Fire ...

  7. Carbon Monoxide Information Center

    Medline Plus

    Full Text Available ... Unites States die every year from accidental non-fire related CO poisoning associated with consumer products, including ... CO Blogs Research & Statistics JANUARY 07, 2016 Non-Fire Carbon Monoxide Deaths Associated with the Use of ...

  8. Carbon Monoxide Information Center

    Medline Plus

    Full Text Available ... Import Safety International Recall Guidance Civil and Criminal Penalties Federal Court Orders & ... 07, 2016 Non-Fire Carbon Monoxide Deaths Associated with the Use of Consumer Products 2012 ...

  9. Carbon Monoxide Nonattainment Areas

    Data.gov (United States)

    U.S. Environmental Protection Agency — This data layer identifies areas in the U.S. where air pollution levels have not met the National Ambient Air Quality Standards (NAAQS) for Carbon Monoxide and have...

  10. Carbon Monoxide Information Center

    Medline Plus

    Full Text Available ... Unites States die every year from accidental non-fire related CO poisoning associated with consumer products, including ... CO Blogs Research & Statistics JANUARY 07, 2016 Non-Fire Carbon Monoxide Deaths Associated with the Use of ...

  11. Statistical data analysis method for multi-zonal airflow measurement using multiple kinds of perfluorocarbon tracer gas

    Energy Technology Data Exchange (ETDEWEB)

    Okuyama, Hiroyasu; Onishi, Yoshinori [Institute of Technology, Shimizu Corporation, 4-17, Etchujima 3-chome, Koto-ku, Tokyo 135-8530 (Japan); Tanabe, Shin-ichi [School of Science and Engineering, Department of Architecture, Waseda University, 3-4-1 Okubo, Shinjyuku-ku, Tokyo 169-8555 (Japan); Kashihara, Seiichi [R and D Laboratories, Asahi Kasei Homes Corporation, 2-1, Samejima Fuji-shi, Shizuoka 416-8501 (Japan)

    2009-03-15

    Conventional multi-zonal ventilation measurement methods by multiple types of perfluorocarbon tracers use a number of different gases equal to the number of zones (n). The possible n x n+n airflows are estimated from the mass balance of the gases and the airflow balance. However, some airflows may not occur because of inter-zonal geometry, and the introduction of unnecessary, unknown parameters can impair the accuracy of the estimation. Also, various error factors often yield an irrational negative airflow rate. Conventional methods are insufficient for the evaluation of error. This study describes a way of using the least-squares technique to improve the precision of estimation and to evaluate reliability. From the equations' residual, the error variance-covariance matrix {lambda}{sub q} of the estimated airflow rate error is deduced. In addition, the coefficient of determinant using the residual sum of squares and total variation is introduced. Furthermore, the error matrix{sub m}{lambda}{sub q} from the measurement errors in the gas concentration and gas emission rate is deduced. The discrepancy ratio of the model premises is defined by dividing the diagonal elements of the former by those of the latter. Moreover, the index of irrationality of the estimated negative airflow rate is defined, based on the different results of the three estimation methods. Some numerical experiments are also carried out to verify the flow rate estimation and the reliability evaluation theory. (author)

  12. Analytical error analysis of Clifford gates by the fault-path tracer method

    Science.gov (United States)

    Janardan, Smitha; Tomita, Yu; Gutiérrez, Mauricio; Brown, Kenneth R.

    2016-08-01

    We estimate the success probability of quantum protocols composed of Clifford operations in the presence of Pauli errors. Our method is derived from the fault-point formalism previously used to determine the success rate of low-distance error correction codes. Here we apply it to a wider range of quantum protocols and identify circuit structures that allow for efficient calculation of the exact success probability and even the final distribution of output states. As examples, we apply our method to the Bernstein-Vazirani algorithm and the Steane [[7,1,3

  13. Regeneration of unmyelinated and myelinated sensory nerve fibres studied by a retrograde tracer method

    DEFF Research Database (Denmark)

    Lozeron, Pierre; Krarup, Christian; Schmalbruch, Henning

    2004-01-01

    Regeneration of myelinated and unmyelinated sensory nerve fibres after a crush lesion of the rat sciatic nerve was investigated by means of retrograde labelling. The advantage of this method is that the degree of regeneration is estimated on the basis of sensory somata rather than the number...

  14. A new method for studying water mass origins on basin scales: using multiple passive tracers to study Atlantic Cold Tongue variability

    Science.gov (United States)

    White, Rachel

    2015-04-01

    Multiple passive tracers are used in a dynamical ocean model to demonstrate a new method to study water mass origins on a basin-wide scale. This method has previously only been used in estuary-scale studies. A case study is chosen to highlight when this multiple passive tracer method may provide benefits over the standard method of tracing water mass origins on basin-scales: using a single passive tracer in an adjoint model. 31 passive tracers are used to determine the origin regions of the Atlantic cold tongue (ACT). At the time of the ACT minimum in sea surface temperature, 38 ± 3% of the surface water in the central equatorial Atlantic is found to originate in the western side of the basin, with 11 ± 2% originating in the east. The multiple passive tracer method can show how origin regions change with time, allowing seasonal differences in origin regions to be discerned. The identification of origin regions of cold water that increase their supply to the equatorial Atlantic in phase with the ACT cooling identifies those regions that are important to the ACT variability. Sensitivity tests show that the temporal evolution of the concentrations of such tracers within the ACT region is not sensitive to the month in which the tracers are initialised. The region of the North Brazil undercurrent is found to be the most important origin region for the central Atlantic ACT region, for a 6-8 month lead time. Using the Met Office EN4 observational dataset of ocean temperatures, correlations are found between January temperatures in the North Brazil undercurrent region and both the ACT mean temperature and ACT spatial extent in July-August, significant at the 0.95 level. This suggests that the 6-month lead-time predictability of the ACT may be increased by improved knowledge of the North Brazil undercurrent temperature. Results from previous studies suggest that such increased predictability of the ACT could potentially help improve predictions of the West African monsoon.

  15. When Phase Contrast Fails: ChainTracer and NucTracer, Two ImageJ Methods for Semi-Automated Single Cell Analysis Using Membrane or DNA Staining

    NARCIS (Netherlands)

    Syvertsson, S.; Vischer, N.O.E.; Gao, Y.; Hamoen, L.W.

    2016-01-01

    Within bacterial populations, genetically identical cells often behave differently. Single-cell measurement methods are required to observe this heterogeneity. Flow cytometry and fluorescence light microscopy are the primary methods to do this. However, flow cytometry requires reasonably strong fluo

  16. Detecting groundwater discharge dynamics from point to catchment scale in a lowland stream: combining hydraulic and tracer methods

    Directory of Open Access Journals (Sweden)

    J. B. Poulsen

    2014-12-01

    Full Text Available Detecting, quantifying, and understanding groundwater discharge to streams are crucial for the assessment of water, nutrient and contaminant exchange at the surface water–groundwater interface. In lowland agricultural catchments with significant groundwater discharge this is of particular importance because of the risk of excess leaching of nutrients to streams. Here we aim to combine hydraulic and tracer methods from point to catchment scale to assess the temporal and spatial variability of groundwater discharge in a lowland, groundwater gaining stream in Denmark. At the point scale groundwater fluxes to the stream were quantified based on Vertical streambed Temperature Profiles (VTP. At the reach scale (0.15–2 km the spatial distribution of zones of focused groundwater discharge was investigated by the use of Distributed Temperature Sensing (DTS. Groundwater discharge to the stream was quantified using differential gauging with an Acoustic Doppler Current Profiler (ADCP. At the catchment scale (26–114 km2 runoff sources during main rain events were investigated by hydrograph separations based on Electrical Conductivity (EC and stable isotopes 2H / 1H. Clear differences in runoff sources between catchments were detected, ranging from approximately 65% event water for the most responsive sub-catchment and less than 10% event water for the least responsive sub-catchment. This shows a large variability in groundwater discharge to the stream, despite the similar lowland characteristics of sub-catchments, indicating the usefulness of environmental tracers for obtaining information about integrated catchment functioning during events. There were also clear spatial patterns of focused groundwater discharge detected by the DTS and ADCP measurements at the reach scale suggesting high spatial variability, where a significant part of groundwater discharge was concentrated in few zones indicating the possibility of concentrated nutrient or pollutant

  17. Measurement of Intestinal and Peripheral Cholesterol Fluxes by a Dual-Tracer Balance Method.

    Science.gov (United States)

    Ronda, Onne A H O; van Dijk, Theo H; Verkade, H J; Groen, Albert K

    2016-12-01

    Long-term elevated plasma cholesterol levels put individuals at risk for developing atherosclerosis. Plasma cholesterol levels are determined by the balance between cholesterol input and output fluxes. Here we describe in detail the methodology to determine the different cholesterol fluxes in mice. The percentage of absorbed cholesterol is calculated from a stable isotope-based double-label method. Cholesterol synthesis is calculated from MIDA after (13) C-acetate enrichment. Cholesterol is removed from the body via the feces. The fecal excretion route is either biliary or non-biliary. The non-biliary route is dominated by trans-intestinal cholesterol efflux, or TICE. Biliary excretion of cholesterol is measured by collecting bile. Non-biliary excretion is calculated by computational modeling. In this article, we describe methods and procedures to measure and calculate dietary intake of cholesterol, fractional cholesterol absorption, fecal neutral sterol output, biliary cholesterol excretion, TICE, cholesterol synthesis, peripheral fluxes, and whole-body cholesterol balance. © 2016 by John Wiley & Sons, Inc.

  18. A novel $^{83\\mathrm{m}}$Kr tracer method for characterizing xenon gas and cryogenic distillation systems

    CERN Document Server

    Rosendahl, S; Brown, E; Cristescu, I; Fieguth, A; Huhmann, C; Lebeda, O; Levy, C; Murra, M; Schneider, S; Vénos, D; Weinheimer, C

    2014-01-01

    The radioactive isomer $^{83\\mathrm{m}}$Kr has many properties that make it very useful for various applications. Its low energy decay products, like conversion, shake-off and Auger electrons as well as X- and $\\gamma$-rays are used for calibration purposes in neutrino mass experiments and direct dark matter detection experiments. Thanks to the short half-life of 1.83 h and the decay to the ground state $^{83}$Kr, one does not risk contamination of any low-background experiment with long- lived radionuclides. In this paper, we present two new applications of $^{83\\mathrm{m}}$Kr. It can be used as a radioactive tracer in noble gases to characterize the particle flow inside of gas routing systems. A method of doping $^{83\\mathrm{m}}$Kr into xenon gas and its detection, using special custom-made detectors, based on a photomultiplier tube, is described. This technique has been used to determine the circulation speed of gas particles inside of a gas purification system for xenon. Furthermore, 83m Kr can be used to...

  19. An accurate method for microanalysis of carbon monoxide in putrid postmortem blood by head-space gas chromatography-mass spectrometry (HS/GC/MS).

    Science.gov (United States)

    Hao, Hongxia; Zhou, Hong; Liu, Xiaopei; Zhang, Zhong; Yu, Zhongshan

    2013-06-10

    Carbon monoxide (CO) may be the cause of more than half the fatal poisonings reported in many countries, with some of these cases under-reported or misdiagnosed by medical professionals. Therefore, an accurate and reliable analytical method to measure blood carboxyhemoglobin level (COHb%), in the 1% to lethal range, is essential for correct diagnosis. Herein a method was established, i.e. head-space gas chromatography-mass spectrometry (HS/GC/MS) that has numerous advantages over other techniques, such as UV spectrometry, for determination of COHb%. There was a linear relationship (R(2)=0. 9995) between the peak area for CO and the COHb% in blood. Using a molecular sieve-packed column, CO levels in the air down to 0.01% and COHb% levels in small blood samples down to 0.2% could be quantitated rapidly and accurately. Furthermore, this method showed good reproducibility with a relative standard deviation for COHb% of <1%. Therefore, this technique provides an accurate and reliable method for determining CO and COHb% levels and may prove useful for investigation of deaths potentially related to CO exposure.

  20. Boundary integral method application in the transportation modeling of radioactive tracers in porous ways; Aplicacao do metodo da integral de contorno na modelagem do transporte de tracadores radioativos em meios porosos

    Energy Technology Data Exchange (ETDEWEB)

    Ferroni, Jose Geraldo

    1996-03-01

    This work describes a method for estimating the effluent concentrations of radioactive tracers in production wells, considering well to well injection tests and piston-like displacements of fluids in the reservoir. The model for tracer transportation takes into account effects of convection and hydrodynamic dispersion. (author)

  1. A nonequilibrium simulation method for calculating tracer diffusion coefficients of small solutes in n-alkane liquids and polymers

    NARCIS (Netherlands)

    van der Vegt, N.F.A.; Briels, Willem J.; Wessling, Matthias; Strathmann, H.

    1998-01-01

    The tracer diffusion coefficients of methane in n-alkane liquids of increasing chain length were calculated by measuring the friction from short time nonequilibrium molecular dynamics simulations. The frictional constant was calculated from the exponentially decaying distance between two methane tra

  2. Cardiac metabolism in mice: tracer method developments and in vivo application revealing profound metabolic inflexibility in diabetes

    National Research Council Canada - National Science Library

    Nicholas D. Oakes; Pia Thalén; Ellen Aasum; Amanda Edgley; Terje Larsen; Stuart M. Furler; Bengt Ljung; David Severson

    2006-01-01

    ...) mice, based on cardiac uptake of (R)-2-[9,10-3H]bromopalmitate ([3H]R-BrP) and 2-deoxy-d-[U-14C]glucose tracers. To obtain quantitative information about the evaluation of cardiac FFA utilization...

  3. Proceedings of the atmospheric tracers and tracer application workshop

    Energy Technology Data Exchange (ETDEWEB)

    Barr, S.; Gedayloo, T. (comps.)

    1979-12-01

    In addition to presentations by participating members a general discussion was held in order to summarize and outline the goals and objectives of the workshop. A number of new low level background tracers such as heavy methanes, perfluorocarbons, multiply labeled isotopes such as /sup 13/C/sup 18/O/sub 2/, helium 3, in addition to sample collection techniques and analytical methods for various tracers were discussed. This report is a summary of discussions and papers presented at this workshop.

  4. Comparison of the ensemble Kalman filter and 4D-Var assimilation methods using a stratospheric tracer transport model

    Directory of Open Access Journals (Sweden)

    S. Skachko

    2014-01-01

    Full Text Available The Ensemble Kalman filter (EnKF assimilation method is applied to the tracer transport using the same stratospheric transport model as in the 4D-Var assimilation system BASCOE. This EnKF version of BASCOE was built primarily to avoid the large costs associated with the maintenance of an adjoint model. The EnKF developed in BASCOE accounts for two adjustable parameters: a parameter α controlling the model error term and a parameter r controlling the observational error. The EnKF system is shown to be markedly sensitive to these two parameters, which are adjusted based on the monitoring of a χ2-test measuring the misfit between the control variable and the observations. The performance of the EnKF and 4D-Var versions was estimated through the assimilation of Aura-MLS ozone observations during an 8 month period which includes the formation of the 2008 Antarctic ozone hole. To ensure a proper comparison, despite the fundamental differences between the two assimilation methods, both systems use identical and carefully calibrated input error statistics. We provide the detailed procedure for these calibrations, and compare the two sets of analyses with a focus on the lower and middle stratosphere where the ozone lifetime is much larger than the observational update frequency. Based on the Observation-minus-Forecast statistics, we show that the analyses provided by the two systems are markedly similar, with biases smaller than 5% and standard deviation errors smaller than 10% in most of the stratosphere. Since the biases are markedly similar, they have most probably the same causes: these can be deficiencies in the model and in the observation dataset, but not in the assimilation algorithm nor in the error calibration. The remarkably similar performance also shows that in the context of stratospheric transport, the choice of the assimilation method can be based on application-dependent factors, such as CPU cost or the ability to generate an ensemble

  5. The use of FTIR technique for determination of gas phase emissions from wood pellet manufacturing. Evaluation of the Time Correlated Tracer (TCT) method for assessment of diffuse terpene emissions from wood pellet production; Anvaendning av FTIR teknik foer bestaemning av gasformiga emissioner vid traepelletstillverkning. Utvaerdering av Time Correlated Tracer (TCT)-metoden foer bestaemning av diffusa terpenemissioner fraan pelletstillverkning

    Energy Technology Data Exchange (ETDEWEB)

    Svedberg, Urban; Galle, Bo [Sundsvall Hospital (Sweden). Clinic of Occupational and Environmental Medicine

    2001-04-01

    In the original project proposal, quantification of the total emission of terpenes from wood pellet manufacturing with the novel TCT-method (Time Correlated Tracer) based on FTIR-technique (Fourier Transform Infrared) and tracer gas was suggested. The expected outcome was a general algorithm for the calculations of the emissions expressed as amount emitted per unit produced. This information would be useful when planning the location of new facilities in relation to domestic housing as well as to other industrial activities. Initial point sampling with an FTIR White cell was made in order to establish the locations of the sources of terpene emissions. The results showed that the dominating terpene emissions came from the smoke stacks gases and was not of such diffuse nature as originally believed. Neither in the pellet storage room, inside the main process facilities, outside the buildings, nor close to the wood chip storage piles, could terpene be detected with the FTIR point sampling cell. In the smoke stack gases terpenes, carbon monoxide, carbon dioxide, acetone, methanol, ethylene, acetylene, formaldehyde and methane was detected. The conclusions so far is that it is not economically or scientifically justifiable to continue the measurements with the proposed TCT method since, the terpene emissions are not of a diffuse nature. Instead it is concluded that terpene emission is best established by direct measurement in the smoke stack gases. In accordance with the intentions of the project, an algorithm for the terpene emission was established based on the measurements in the smoke stack gases. This algorithm shows an average emission of 255 grams of terpenes per produced ton of pellets. This gives an annual emission of 21,700 kg of gaseous terpenes from the investigated plant, based on an annual production of 85,000 tons pellets. When compared to other establishments processing wood, i.e. saw mills, this amount is not large. The results shed some light on other

  6. Quantification of emissions due to the natural gas storage well-casing blowout at Aliso Canyon/SS-25 using tracer flux ratio methods.

    Science.gov (United States)

    Herndon, S. C.; Daube, C.; Jervis, D.; Yacovitch, T. I.; Roscioli, J. R.; Curry, J.; Nelson, D. D.; Knighton, W. B.

    2016-12-01

    The methane emission rate from the well blowout at Aliso Canyon Natural Gas Storage Facility in Porter Ranch, California was quantified using the tracer flux ratio method (TFR). Over 400 tracer plume transects were collected, each lasting 15-300 seconds, using instrumentation aboard a mobile platform on 25 days between December 21, 2015 and March 9, 2016. The leak rate from October 23rd to February 11th has been estimated here using a combination of our leak rate measurements (TFR) and the flight mass balance (FMB) data [Conley et al., 2016]. The TFR approach employed here is assessing only the leaks due to the SS-25 well blowout and excludes other possible emissions at the facility. By "calibrating" the FMB dataset, the leak rate is integrated from Oct 23rd to December 21th. The sum of the inferred inferred and measured meissions suggests a total leak burden of 86,022 ± 8,393 metric tons of CH4. The primary uncertainty in this value is due to the uncertainty in the emission rate prior to the beginning of the TFR quantification. The ethane to methane enhancement ratio observed downwind of the leak site is consistent with the content of ethane in the natural gas at this site and provides definitive evidence that the methane emission rate quantified via tracer flux ratio is not due to a nearby landfill or other potential biogenic sources.

  7. An experimental application of the Periodic Tracer Hierarchy (PERTH) method to quantify time-variable water and solute transport in a sloping soil lysimeter

    Science.gov (United States)

    Pangle, L. A.; Cardoso, C.; Kim, M.; Lora, M.; Wang, Y.; Troch, P. A. A.; Harman, C. J.

    2014-12-01

    sequence of rainfall pulses and achieved periodic-steady-state conditions over 24 days. Using systematic introductions of deuterium- and chloride-enriched water, and the PERTH method, we resolve the time-conditional TTDs associated with tracer injections that occurred during specific intervals of the overall rainfall sequence.

  8. Tracer tomography (in) rocks!

    Science.gov (United States)

    Somogyvári, Márk; Jalali, Mohammadreza; Jimenez Parras, Santos; Bayer, Peter

    2016-04-01

    Physical behavior of fractured aquifers is rigorously controlled by the presence of interconnected conductive fractures, as they represent the main pathways for flow and transport. Ideally, they are simulated as a discrete fracture network (DFN) in a model to capture the role of fracture system geometry, i.e. fracture length, height, and width (aperture/transmissivity). Such network may be constrained by prior geological information or direct data resources such as field mapping, borehole logging and geophysics. With the many geometric features, however, calibration of a DFN to measured data is challenging. This is especially the case when spatial properties of a fracture network need to be calibrated to flow and transport data. One way to increase the insight in a fractured rock is by combining the information from multiple field tests. In this study, a tomographic configuration that combines multiple tracer tests is suggested. These tests are conducted from a borehole with different injection levels that act as sources. In a downgradient borehole, the tracer is recorded at different levels or receivers, in order to maximize insight in the spatial heterogeneity of the rock. As tracer here we chose heat, and temperature breakthrough curves are recorded. The recorded tracer data is inverted using a novel stochastic trans-dimensional Markov Chain Monte Carlo procedure. An initial DFN solution is generated and sequentially modified given available geological information, such as expected fracture density, orientation, length distribution, spacing and persistency. During this sequential modification, the DFN evolves in a trans-dimensional inversion space through adding and/or deleting fracture segments. This stochastic inversion algorithm requires a large number of thousands of model runs to converge, and thus using a fast and robust forward model is essential to keep the calculation efficient. To reach this goal, an upwind coupled finite difference method is employed

  9. Method for Determination of Neptunium in Large-Sized Urine Samples Using Manganese Dioxide Coprecipitation and 242Pu as Yield Tracer

    DEFF Research Database (Denmark)

    Qiao, Jixin; Hou, Xiaolin; Roos, Per

    2013-01-01

    A novel method for bioassay of large volumes of human urine samples using manganese dioxide coprecipitation for preconcentration was developed for rapid determination of 237Np. 242Pu was utilized as a nonisotopic tracer to monitor the chemical yield of 237Np. A sequential injection extraction...... to 100% and high separation capacity of processing up to 5 L of human urine samples. The MnO2 coprecipitation process is simple and straightforward in which a batch (8–12) of samples can be pretreated within 4 h (i.e.,

  10. Tracer tests in geothermal resource management

    Directory of Open Access Journals (Sweden)

    Axelsson G.

    2013-05-01

    Full Text Available Geothermal reinjection involves injecting energy-depleted fluid back into geothermal systems, providing an effective mode of waste-water disposal as well as supplementary fluid recharge. Cooling of production boreholes is one of the main disadvantages associated with reinjection, however. Tracer testing is an important tool for reinjection studies because tracer tests actually have a predictive power since tracer transport is orders of magnitude faster than cold-front advancement around reinjection boreholes. A simple and efficient method of tracer test interpretation, assuming specific flow channels connecting reinjection and production boreholes, is available. It simulates tracer return profiles and estimates properties of the flow channels, which are consequently used for predicting the production borehole cooling. Numerous examples are available worldwide on the successful application of tracer tests in geothermal management, many involving the application of this interpretation technique. Tracer tests are also used for general subsurface hydrological studies in geothermal systems and for flow rate measurements in two-phase geothermal pipelines. The tracers most commonly used in geothermal applications are fluorescent dyes, chemical substances and radioactive isotopes. New temperature-resistant tracers have also been introduced and high-tech tracers are being considered.

  11. Syncope Associated with Carbon Monoxide Poisoning due to Narghile Smoking

    Directory of Open Access Journals (Sweden)

    Seda Ozkan

    2013-01-01

    Full Text Available Narghile smoking is a traditional method of tobacco use, and it has been practiced extensively for 400 years. Traditionally, narghile smoking is a matter of culture mainly in Middle East, Asia, and Africa. In recent years, its use as a social activity has increased worldwide, especially among young people. Narghile smoking is an unusual cause of carbon monoxide poisoning. Narghile smoking, compared to cigarette smoking, can result in more smoke exposure and greater levels of carbon monoxide. We present an acute syncope case of a 19-year-old male patient who had carbon monoxide poisoning after narghile smoking.

  12. Solid Matrix Transformation and Tracer Addition using Molten Ammonium Bifluoride Salt as a Sample Preparation Method for Laser Ablation Inductively Coupled Plasma Mass Spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Grate, Jay W.; Gonzalez, Jhanis J.; O' Hara, Matthew J.; Kellogg, Cynthia M.; Morrison, Samuel S.; Koppenaal, David W.; Chan, George C.; Mao, Xianglei; Zorba, Vassilia; Russo, Richard

    2017-09-08

    Laser ablation (LA) is a means of sample introduction to inductively coupled plasma (ICP) mass spectrometry (MS) that avoids acid dissolution and chemical separation steps conventionally associated with solid sample analysis. At the same time, certain features of LA-ICP-MS are often mentioned in critical reviews including solid matrix variability and its influence on the ablation process, matrix dependent elemental fractionation, lack of matrix matched standards for external calibration, and limitations to internal calibration because it is challenging to add and distribute spikes into solid samples. In this paper we introduce the concept of a synergistic minimal sample preparation method that is used in combination with LA-ICP-MS as a means to overcome these limitations. The aim of this minimal sample preparation procedure is to reactively transform the original matrix to a more consistent matrix for LA-based analysis, thus reducing the effects of matrix variability, while enabling the addition of tracers. In conjunction with ICP-MS, we call this MTR-LA-ICP-MS, where MTR is derived from matrix transformation including the option to add tracers

  13. Transient methods to characterize flows and mass transfer in a packed column by tracers; Methodes transitoires de caracterisation des ecoulements et du transfert de masse dans une colonne a garnissage a l'aide de traceurs

    Energy Technology Data Exchange (ETDEWEB)

    Perrin, S.

    1998-06-11

    The aim of this study is to propose a packed column characterization method in the form of phases flows and mass transfer model, in which the parameters are estimated by transient technique. After a bibliographic study a model is performed and validated. It allows efficiency and precision in the parameters choice. Two tracer techniques have been implemented: they show interesting possibilities of flow diagnosis. (A.L.B.)

  14. Packet Tracer network simulator

    CERN Document Server

    Jesin, A

    2014-01-01

    A practical, fast-paced guide that gives you all the information you need to successfully create networks and simulate them using Packet Tracer.Packet Tracer Network Simulator is aimed at students, instructors, and network administrators who wish to use this simulator to learn how to perform networking instead of investing in expensive, specialized hardware. This book assumes that you have a good amount of Cisco networking knowledge, and it will focus more on Packet Tracer rather than networking.

  15. Assessment of carbon monoxide values in smokers: a comparison of carbon monoxide in expired air and carboxyhaemoglobin in arterial blood

    DEFF Research Database (Denmark)

    Andersson, Mette F; Møller, Ann M

    2010-01-01

    Smoking increases perioperative complications. Carbon monoxide concentrations can estimate patients' smoking status and might be relevant in preoperative risk assessment. In smokers, we compared measurements of carbon monoxide in expired air (COexp) with measurements of carboxyhaemoglobin (COHb) ......) in arterial blood. The objectives were to determine the level of correlation and to determine whether the methods showed agreement and evaluate them as diagnostic tests in discriminating between heavy and light smokers....

  16. Carbon Monoxide (CO) Poisoning Prevention

    Science.gov (United States)

    ... Recommend on Facebook Tweet Share Compartir When power outages occur after severe weather (such as winter storms, hurricanes or tornadoes), using alternative sources of power can cause carbon monoxide (CO) to build up in a ...

  17. Carbon Monoxide Mixing Ratio System

    Data.gov (United States)

    Oak Ridge National Laboratory — The Southern Great Plains (SGP) Carbon Monoxide (CO) system provides high-precision atmospheric concentration measurements of CO mixing ratio (ppbv dry air) every 10...

  18. Beach sediments drift study by means of radioactive tracers; L'etude du transport littoral par la methode des traceurs radioactifs

    Energy Technology Data Exchange (ETDEWEB)

    Hours, R. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires; Jaffry, P. [Electricite de France (EDF), 78 - Chatou (France). Lab. National d' Hydraulique

    1959-07-01

    The present state of the sediments drift studies by means of radioactive tracers is exposed. Various processes of labelling, immersion and detection, used in France and other countries, are reviewed. A more extended analysis of some aspects of the problem by the same authors can be found in 'La Houille Blanche', number 3, may-june 1959 (Rapport C.E.A. number 1269). (author) [French] L'etude du transport littoral des sediments et galets par la methode des traceurs radioactifs est en plein developpement. Le present rapport precise l'etat actuel de la question. Les techniques de marquage, d'immersion et de detection utilisees en France et a l'etranger sont decrites; une analyse plus detaillee de certains aspects de la question est presentee par les memes auteurs dans 'La Houille Blanche', numero 3, mai-juin 1959 (Rapport C.E.A. numero 1269). (auteur)

  19. Experimental quantification of solute transport through the vadose zone under dynamic boundary conditions with dye tracers and optical methods.

    Science.gov (United States)

    Cremer, Clemens; Neuweiler, Insa

    2017-04-01

    Knowledge of subsurface solute transport processes is vital to investigate e.g. groundwater contamination, nutrient uptake by plant roots and to implement remediation strategies. Beside field measurements and numerical simulations, physical laboratory experiments represent a way to establish process understanding and furthermore validate numerical schemes. Atmospheric forcings, such as erratically varying infiltration and evaporation cycles, subject the shallow subsurface to local and temporal variations in water content and associated hydraulic conductivity of the prevailing porous media. Those variations in material properties can cause flow paths to differ between upward and downward flow periods. Thereby, the unsaturated subsurface presents a highly complicated, dynamic system. Following an extensive systematical numerical investigation of flow and transport through bimodal, unsaturated porous media under dynamic boundary conditions (Cremer et al., 2016), we conduct physical laboratory experiments in a 22 cm x 8 cm x 1 cm flow cell where we introduce structural heterogeneity in the form sharp material interfaces between different porous media. In all experiments, a constant pressure head is implemented at the lower boundary, while cyclic infiltration-evaporation phases are applied at the soil surface. As a reference case a stationary infiltration with a rate corresponding to the cycle-averaged infiltration rate is applied. By initial application of dye tracers, solute transport within the domain is visualized such that transport paths and redistribution processes can be observed in a qualitative manner. Solute leaching is quantified at the bottom outlet, where breakthrough curves are obtained via spectroscopy. Liquid and vapor flow in and out of the domain is obtained from multiple balances. Thereby, the interplay of material structural heterogeneity and alternating flow (transport) directions and flow (transport) paths is investigated. Results show lateral

  20. Bacteriophages as surface and ground water tracers

    Directory of Open Access Journals (Sweden)

    P. Rossi

    1998-01-01

    Full Text Available Bacteriophages are increasingly used as tracers for quantitative analysis in both hydrology and hydrogeology. The biological particles are neither toxic nor pathogenic for other living organisms as they penetrate only a specific bacterial host. They have many advantages over classical fluorescent tracers and offer the additional possibility of multi-point injection for tracer tests. Several years of research make them suitable for quantitative transport analysis and flow boundary delineation in both surface and ground waters, including karst, fractured and porous media aquifers. This article presents the effective application of bacteriophages based on their use in differing Swiss hydrological environments and compares their behaviour to conventional coloured dye or salt-type tracers. In surface water and karst aquifers, bacteriophages travel at about the same speed as the typically referenced fluorescent tracers (uranine, sulphurhodamine G extra. In aquifers of interstitial porosity, however, they appear to migrate more rapidly than fluorescent tracers, albeit with a significant reduction in their numbers within the porous media. This faster travel time implies that a modified rationale is needed for defining some ground water protection area boundaries. Further developments of other bacteriophages and their documentation as tracer methods should result in an accurate and efficient tracer tool that will be a proven alternative to conventional fluorescent dyes.

  1. Bacteriophages as surface and ground water tracers

    Science.gov (United States)

    Rossi, P.; Dörfliger, N.; Kennedy, K.; Müller, I.; Aragno, M.

    Bacteriophages are increasingly used as tracers for quantitative analysis in both hydrology and hydrogeology. The biological particles are neither toxic nor pathogenic for other living organisms as they penetrate only a specific bacterial host. They have many advantages over classical fluorescent tracers and offer the additional possibility of multi-point injection for tracer tests. Several years of research make them suitable for quantitative transport analysis and flow boundary delineation in both surface and ground waters, including karst, fractured and porous media aquifers. This article presents the effective application of bacteriophages based on their use in differing Swiss hydrological environments and compares their behaviour to conventional coloured dye or salt-type tracers. In surface water and karst aquifers, bacteriophages travel at about the same speed as the typically referenced fluorescent tracers (uranine, sulphurhodamine G extra). In aquifers of interstitial porosity, however, they appear to migrate more rapidly than fluorescent tracers, albeit with a significant reduction in their numbers within the porous media. This faster travel time implies that a modified rationale is needed for defining some ground water protection area boundaries. Further developments of other bacteriophages and their documentation as tracer methods should result in an accurate and efficient tracer tool that will be a proven alternative to conventional fluorescent dyes.

  2. Development and initial evaluation of a novel method for assessing tissue-specific plasma free fatty acid utilization in vivo using (R)-2-bromopalmitate tracer.

    Science.gov (United States)

    Oakes, N D; Kjellstedt, A; Forsberg, G B; Clementz, T; Camejo, G; Furler, S M; Kraegen, E W; Olwegård-Halvarsson, M; Jenkins, A B; Ljung, B

    1999-06-01

    We describe a method for assessing tissue-specific plasma free fatty acid (FFA) utilization in vivo using a non-beta-oxidizable FFA analog, [9,10-3H]-(R)-2-bromopalmitate (3H-R-BrP). Ideally 3H-R-BrP would be transported in plasma, taken up by tissues and activated by the enzyme acyl-CoA synthetase (ACS) like native FFA, but then 3H-labeled metabolites would be trapped. In vitro we found that 2-bromopalmitate and palmitate compete equivalently for the same ligand binding sites on albumin and intestinal fatty acid binding protein, and activation by ACS was stereoselective for the R-isomer. In vivo, oxidative and non-oxidative FFA metabolism was assessed in anesthetized Wistar rats by infusing, over 4 min, a mixture of 3H-R-BrP and [U-14C] palmitate (14C-palmitate). Indices of total FFA utilization (R*f) and incorporation into storage products (Rfs') were defined, based on tissue concentrations of 3H and 14C, respectively, 16 min after the start of tracer infusion. R*f, but not Rfs', was substantially increased in contracting (sciatic nerve stimulated) hindlimb muscles compared with contralateral non-contracting muscles. The contraction-induced increases in R*f were completely prevented by blockade of beta-oxidation with etomoxir. These results verify that 3H-R-BrP traces local total FFA utilization, including oxidative and non-oxidative metabolism. Separate estimates of the rates of loss of 3H activity indicated effective 3H metabolite retention in most tissues over a 16-min period, but appeared less effective in liver and heart. In conclusion, simultaneous use of 3H-R-BrP and [14C]palmitate tracers provides a new useful tool for in vivo studies of tissue-specific FFA transport, utilization and metabolic fate, especially in skeletal muscle and adipose tissue.

  3. Simple, inexpensive method of determining total body water using a tracer dose of D/sub 2/O and infrared absorption of biological fluids

    Energy Technology Data Exchange (ETDEWEB)

    Lukaski, H.C.; Johnson, P.E.

    1985-02-01

    An improved infrared spectrophotometric method using tracer doses of D/sub 2/O for determination of total body water (TBW) is described. Evaluation of sample preparation procedures showed that only vacuum sublimation yielded acceptable recoveries of D/sub 2/O standards in the range of 0.01-0.30 mg/ml in urine and plasma (101 +/- 2.5 and 99.6 +/- 2.6%, mean +/- SD, respectively). Oral administration of a 10 g dose of D/sub 2/O was shown to equilibrate within 2 hr in the saliva and plasma of 10 healthy men and women, including obese (30% body fat) subjects. Calculated TBW was 39.1 +/- 6.4 L which represented 74 +/- 1.6% of the fat free mass determined by hydrodensitometry. The precision of the described infrared method was 2.5%. Based upon the observed sensitivity of this method, it would be possible to administer smaller oral D/sub 2/O doses, 5-6 g, and obtain reliable TBW values. The practical advantages of this method are low cost and a simple analysis that permits repeated TBW measurements over brief periods without an undue buildup of background deuterium levels in the body.

  4. A rapid method for the measurement of sulfur hexafluoride (SF6), trifluoromethyl sulfur pentafluoride (SF5CF3), and Halon 1211 (CF2ClBr) in hydrologic tracer studies

    Science.gov (United States)

    Busenberg, Eurybiades; Plummer, L. Niel

    2010-01-01

    A rapid headspace method for the simultaneous laboratory determination of intentionally introduced hydrologic tracers, sulfur hexafluoride (SF6), trifluoromethyl sulfur pentafluoride (SF5CF3), Halon 1211 (CF2ClBr), and other halocarbons in water and gases is described. The high sensitivity of the procedure allows for introduction of minimal tracer mass (a few grams) into hydrologic systems with a large dynamic range of analytical detection (dilutions to 1:108). Analysis times by gas chromatography with electron capture detector are less than 1 min for SF6; about 2 min for SF6 and SF5CF3; and 4 min for SF6, SF5CF3, and Halon 1211. Many samples can be rapidly collected, preserved in stoppered septum bottles, and analyzed at a later time in the laboratory. Examples are provided showing the effectiveness of the gas tracer test studies in varied hydrogeological settings.

  5. Tracer attenuation in groundwater

    Science.gov (United States)

    Cvetkovic, Vladimir

    2011-12-01

    The self-purifying capacity of aquifers strongly depends on the attenuation of waterborne contaminants, i.e., irreversible loss of contaminant mass on a given scale as a result of coupled transport and transformation processes. A general formulation of tracer attenuation in groundwater is presented. Basic sensitivities of attenuation to macrodispersion and retention are illustrated for a few typical retention mechanisms. Tracer recovery is suggested as an experimental proxy for attenuation. Unique experimental data of tracer recovery in crystalline rock compare favorably with the theoretical model that is based on diffusion-controlled retention. Non-Fickian hydrodynamic transport has potentially a large impact on field-scale attenuation of dissolved contaminants.

  6. Constraints on primary and secondary particulate carbon sources using chemical tracer and 14C methods during CalNex-Bakersfield

    Data.gov (United States)

    U.S. Environmental Protection Agency — The present study investigates primary and secondary sources of organic carbon for Bakersfield, CA, USA as part of the 2010 CalNex study. The method used here...

  7. Evaluation of leakage from fume hoods using tracer gas, tracer nanoparticles and nanopowder handling test methodologies.

    Science.gov (United States)

    Dunn, Kevin H; Tsai, Candace Su-Jung; Woskie, Susan R; Bennett, James S; Garcia, Alberto; Ellenbecker, Michael J

    2014-01-01

    The most commonly reported control used to minimize workplace exposures to nanomaterials is the chemical fume hood. Studies have shown, however, that significant releases of nanoparticles can occur when materials are handled inside fume hoods. This study evaluated the performance of a new commercially available nano fume hood using three different test protocols. Tracer gas, tracer nanoparticle, and nanopowder handling protocols were used to evaluate the hood. A static test procedure using tracer gas (sulfur hexafluoride) and nanoparticles as well as an active test using an operator handling nanoalumina were conducted. A commercially available particle generator was used to produce sodium chloride tracer nanoparticles. Containment effectiveness was evaluated by sampling both in the breathing zone (BZ) of a mannequin and operator as well as across the hood opening. These containment tests were conducted across a range of hood face velocities (60, 80, and 100 ft/min) and with the room ventilation system turned off and on. For the tracer gas and tracer nanoparticle tests, leakage was much more prominent on the left side of the hood (closest to the room supply air diffuser) although some leakage was noted on the right side and in the BZ sample locations. During the tracer gas and tracer nanoparticle tests, leakage was primarily noted when the room air conditioner was on for both the low and medium hood exhaust airflows. When the room air conditioner was turned off, the static tracer gas tests showed good containment across most test conditions. The tracer gas and nanoparticle test results were well correlated showing hood leakage under the same conditions and at the same sample locations. The impact of a room air conditioner was demonstrated with containment being adversely impacted during the use of room air ventilation. The tracer nanoparticle approach is a simple method requiring minimal setup and instrumentation. However, the method requires the reduction in

  8. (Carbon monoxide metabolism by photosynthetic bacteria)

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    Research continued on the metabolism of carbon monoxide by Rhodospirillum rubrum. This report discusses progress on the activity, induction, inhibition, and spectroscopic analysis of the enzyme Carbon Monoxide Dehydrogenase. (CBS)

  9. Quantification of Gas Emissions from Refinieries, Gas Stations, Oil Wells and Agriculture using Optical Solar Occultation Flux and Tracer Correlation Methods

    Science.gov (United States)

    Mellqvist, J.; Samuelsson, J.; Marianne, E.; Brohede, S.; Andersson, P.; Johansson, J.; Isoz, O.; Tisopulos, L.; Polidori, A.; Pikelnaya, O.

    2016-12-01

    Industrial volatile organic compound (VOC) emissions may contribute significantly to ozone formation. In order to investigate how much small sources contribute to the VOC concentrations in the Los Angeles metropolitan area a comprehensive emission study has been carried out on behalf of the South Coast Air Quality Management District (SCAQMD). VOC emissions from major sources such as refineries, oil wells, petrol stations oil depots and oil platforms were measured during September and October 2015 using several unique optical methods, including the Solar Occultation Flux method (SOF) and tracer correlation technique based on extractive FTIR and DOAS combined with an open path multi reflection cell. In addition, measurements of ammonia emissions from farming in Chino were demonstrated. The measurements in this study were quality assured by carrying out a controlled source gas release study and side by side measurements with several other techniques. The results from the field campaign show that the emissions from the above mentioned sources are largely underestimated in inventories with potential impact on the air quality in the Los Angeles metropolitan area. The results show that oil and gas production is a very significant VOC emission source. In this presentation the techniques will be discussed together with the main results from the campaign including the quality assurance work.

  10. Separation of run-off components of a glacierized catchment in Kyrgyzstan, Central Asia, by tracer methods (mainly δ2H, δ18O) and meteorological data

    Science.gov (United States)

    Weise, Stephan M.; Unger-Shayesteh, Katy; Vorogushyn, Sergiy; Kalashnikova, Olga; Ershova, Natalya

    2017-04-01

    Since 2014 the glacierized Ala Archa catchment (ca. 230 km2) in the Kyrgyz Alatau mountains south of Bishkek is investigated for run-off contributions of precipitation, groundwater, snow-melt, and glacier melt by tracer methods (δ2H, δ18O, electrical conductivity) and hydro-meteorological data (run-off, precipitation, air temperature, albedo). The investigation period is characterized by a high inter-annual variability in precipitation amount and summer run-off. The isotopic composition of run-off water is found to be governed more by the interplay of air temperature, precipitation history, and snow coverage than by its origin from direct precipitation, snow- or glacial melt. The isotopic composition of base flow in winter and early spring time is found to vary probably not due to a reservoir (mixing) but due to a phase exchange process (fractionation). In the light of these results a separation of all run-off components in such an environment simply with isotope methods appears to be unrealistic.

  11. Using Tracer Technology to Characterize Contaminated Pipelines

    Energy Technology Data Exchange (ETDEWEB)

    Maresca, Joseph, W., Jr., Ph.D.; Bratton, Wesley, L., Ph.D., P.E.; Dickerson, Wilhelmina; Hales, Rochelle

    2005-12-30

    The Pipeline Characterization Using Tracers (PCUT) technique uses conservative and partitioning, reactive or other interactive tracers to remotely determine the amount of contaminant within a run of piping or ductwork. The PCUT system was motivated by a method that has been successfully used to characterize subsurface soil contaminants and is similar in operation to that of a gas chromatography column. By injecting a ?slug? of both conservative and partitioning tracers at one end (or section) of the piping and measuring the time history of the concentration of the tracers at the other end (or another section) of the pipe, the presence, location, and amount of contaminant within the pipe or duct can be determined. The tracers are transported along the pipe or duct by a gas flow field, typically air or nitrogen, which has a velocity that is slow enough so that the partitioning tracer has time to interact with the contaminant before the tracer slug completely passes over the contaminate region. PCUT not only identifies the presence of contamination, it also can locate the contamination along the pipeline and quantify the amount of residual. PCUT can be used in support of deactivation and decommissioning (D&D) of piping and ducts that may have been contaminated with hazardous chemicals such as chlorinated solvents, petroleum products, radioactive materials, or heavy metals, such as mercury.

  12. Comparison of two tracer gas dilution methods for the determination of clothing ventilation and of vapour resistance

    NARCIS (Netherlands)

    Havenith, G.; Zhang, P.; Hatcher, K.; Daanen, H.A.M.

    2010-01-01

    Clothing microclimate ventilation is an important parameter in climatic stress and in contaminated environments. The two main methods for its determination (Crockford et al. (CR) 1972 and Lotens and Havenith (LH) 1988) were, after further development, compared in terms of reproducibility, validity

  13. Count rate balance method of measuring sediment transport of sand beds by radioactive tracers; Methode du bilan des taux de comptage d'indicateurs radioactifs pour la determination du debit de charriage des lits sableux

    Energy Technology Data Exchange (ETDEWEB)

    Sauzay, G. [Commissariat a l' Energie Atomique, 91 - Saclay (France). Centre d' Etudes Nucleaires

    1967-11-01

    Radioactive tracers are applied to the direct measurement of the sediment transport rate of sand beds. The theoretical measurement formula is derived: the variation of the count rate balance is inverse of that of the transport thickness. Simultaneously the representativeness of the tracer is critically studied. The minimum quantity of tracer which has to be injected in order to obtain a correct statistical definition of count rate given by a low number of grains 'seen' by the detector is then studied. A field experiment was made and has let to study the technological conditions for applying this method: only the treatment of results is new, the experiment itself is carried out with conventional techniques applied with great care. (author) [French] Les indicateurs radioactifs sont appliques a la mesure directe du debit de charriage des lits sableux. On etablit la formule theorique de mesure: le bilan des taux de comptage varie en sens inverse de l'epaisseur de charriage. Parallelement on fait une etude critique de la representativite de l'indicateur, puis on determine la quantite minimale de traceur qu'il faut immerger pour que les taux de comptage fournis pour un faible nombre de grains 'vus' par le detecteur aient une definition statistique correcte. Une experience de terrain a permis d'etudier les conditions technologiques de cette methode: seul le depouillement des resultats est nouveau. L'experimentation in-situ se fait suivant les procedes classiques avec un tres grand soin. (auteur)

  14. Optimizing the mercury mass measurement in industrial electrolytic cells by the radio-tracer method at ININ; Optimizacion de la medicion de masa de mercurio en celdas electroliticas industriales por el metodo de radiotrazado en el ININ

    Energy Technology Data Exchange (ETDEWEB)

    Valle R, J.; Angeles C, A., E-mail: Ing.valle.r@hotmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2014-10-15

    One method used in the production of chlorine and sodium is the use of electrolytic cells for the separation of chlorine and sodium from the brine; the industries apply very intense electromagnetic fields in this process. The electrolytic cells use mercury as electrode. In a chlorine production plant inventories are determined by total amount of mercury in the plant annually, since mercury losses are large and a very important parameter is to control the mass of mercury for it is necessary to measure with great precision the losses made. There are several methods to determine the mass of mercury ranging from take samples and weigh, but this involves continuous interruption of the process creating downtimes which in turn represent economic losses giving a result delimiting productivity for the industrial sector. An alternative and attractive method is to use a radioactive tracer whose principle has a similar behavior to study objective. The inert mercury has to be neutron activated in a nuclear reactor to having the characteristics of a tracer; the result makes one of the isotopes of mercury. The tracer is transported taking into account the recommendations of the Comision Nacional de Seguridad Nuclear y Salvaguardias (Mexico), then it is injected into the electrolytic cells mixing with the mercury in the system. By a relative radioactivity measurement and one sample by gamma spectrometry per interest cell, the mass of mercury without stopping the process is obtained. For optimal use of radio-tracer method must be taken into account as important features: irradiation time of mercury, counting conditions, vial geometry, sample volume, sample cells, mixing time and half-life of the tracer. (Author)

  15. Carbon monoxide formation in tomatoes

    Energy Technology Data Exchange (ETDEWEB)

    Gladon, R.J.; Staby, G.L.

    1979-01-01

    Carbon monoxide (CO) is not emanated to any large extent from tomato fruits (Lycopersicon esculentum, Mill. cvs. Rutgers and Ohio MR-13), but is retained within the internal atmosphere. CO is found during all stages of fruit development, but no set pattern of CO concentration is evident.

  16. MOPITT Carbon Monoxide Over India

    Science.gov (United States)

    2002-01-01

    MOPITT observed high levels of carbon monoxide (red and yellow pixels) over the Indian sub-continent during March. These values are associated with industrial activity in the region just south of the Himalayan Mountains. Notice that to the north, the Himalayas are characterized by low values (blue pixels).

  17. Determination of the separation efficiencies of a single-stage cryogenic distillation setup to remove krypton out of xenon by using a (83m)Kr tracer method.

    Science.gov (United States)

    Rosendahl, S; Brown, E; Cristescu, I; Fieguth, A; Huhmann, C; Lebeda, O; Murra, M; Weinheimer, C

    2015-11-01

    The separation of krypton and xenon is of particular importance for the field of direct dark matter search with liquid xenon detectors. The intrinsic contamination of the xenon with radioactive (85)Kr makes a significant background for these kinds of low count-rate experiments and has to be removed beforehand. This can be achieved by cryogenic distillation, a technique widely used in industry, using the different vapor pressures of krypton and xenon. In this paper, we present an investigation on the separation performance of a single stage distillation system using a radioactive (83m)Kr-tracer method. The separation characteristics under different operation conditions are determined for very low concentrations of krypton in xenon at the level of (83m)Kr/Xe = 1.9 ⋅ 10(-15), demonstrating, that cryogenic distillation in this regime is working. The observed separation is in agreement with the expectation from the different volatilities of krypton and xenon. This cryogenic distillation station is the first step on the way to a multi-stage cryogenic distillation column for the next generation of direct dark matter experiment XENON1T.

  18. Tracer monitoring of enhanced oil recovery projects

    Directory of Open Access Journals (Sweden)

    Kleven R.

    2013-05-01

    Full Text Available In enhanced oil recovery (EOR, chemicals are injected into the oil reservoir, either to increase macroscopic sweep efficiency, or to reduce remaining oil saturation in swept zones. Tracers can be used to identify reservoirs that are specifically suited for EOR operations. Injection of a selection of partitioning tracers, combined with frequent sample analysis of produced fluids, provides information suited for estimation of residual oil saturation. Tracers can also be used to evaluate and optimize the application of EOR chemicals in the reservoir. Suitable tracers will follow the EOR chemicals and assist in evaluation of retention, degradation or trapping. In addition to field applications, tracers also have a large potential as a tool to perform mechanistic studies of EOR chemicals in laboratory experiments. By labelling EOR chemicals with radioactive isotopes of elements such as H, C and S, detailed studies of transport mechanisms can be carried out. Co-injection of labelled compounds in dynamic flooding experiments in porous media will give information about retention or separation of the unique compounds constituting the chemical formulation. Separation of such compounds may be detrimental to obtaining the EOR effect expected. The paper gives new information of specific methods, and discusses current status for use of tracers in EOR operations.

  19. Quantifying groundwater exchange rates in a beach barrier lagoon using a radioisotopic tracer and geophysical methods: Younger Lagoon, Santa Cruz, CA

    Science.gov (United States)

    Richardson, C. M.; Swarzenski, P. W.; Johnson, C.

    2013-12-01

    Coastal lagoons are highly productive systems with a strong dependence on the physico-chemical regime of their surrounding environment. Groundwater interactions with the nearshore environment can drive ecosystem stability and productivity. Lagoons with restricted surface connectivity interact with coastal waters via subsurface flow paths that follow natural hydraulic gradients, producing a dynamic freshwater-saltwater mixing zone with submarine groundwater discharge (SGD) regions that are tidally influenced. Recent studies demonstrate the importance of SGD in maintaining nearshore ecology through a number of processes, including enhanced chemical loadings, focused biogeochemical transformations, and complex water mixing scenarios (Slomp and Van Cappellen, 2004 and Taniguchi et al., 2002). Groundwater discharge to the coastal ocean is often slow, diffuse and site-specific. Traditional methods used to evaluate SGD fluxes operate at varying scales and typically result in over or underestimates of SGD. Novel monitoring and evaluation methods are required in order to better understand how coastal aquifer systems influence multi-scalar water and nutrient budgets. Recently developed methods to determine fluid exchange rates include the use of select U- and Th-series radionuclides, multi-channel resistivity imaging, as well as the integration of temperature data and 1-D analytical modeling. Groundwater fluxes were examined in a coastal lagoon system to characterize the physics of subsurface fluid transport evidenced by visible seepage faces at low tide. Fluid exchange rates were quantified to determine the spatial and temporal variability of groundwater movement using thermal time series, water level data, and a coupled radiotracer-geophysical method. Our investigation of subsurface characteristics and groundwater fluxes using both traditional and newly-developed methods indicated that seasonal water inputs and tidal controls on water table elevation significantly

  20. A Standardized Method for the Construction of Tracer Specific PET and SPECT Rat Brain Templates : Validation and Implementation of a Toolbox

    NARCIS (Netherlands)

    Vállez Garcia, David; Casteels, Cindy; Schwarz, Adam J.; Dierckx, Rudi A. J. O.; Koole, Michel; Doorduin, Janine

    2015-01-01

    High-resolution anatomical image data in preclinical brain PET and SPECT studies is often not available, and inter-modality spatial normalization to an MRI brain template is frequently performed. However, this procedure can be challenging for tracers where substantial anatomical structures present l

  1. A standardized method for the construction of tracer specific PET and SPECT rat brain templates: validation and implementation of a toolbox.

    Directory of Open Access Journals (Sweden)

    David Vállez Garcia

    Full Text Available High-resolution anatomical image data in preclinical brain PET and SPECT studies is often not available, and inter-modality spatial normalization to an MRI brain template is frequently performed. However, this procedure can be challenging for tracers where substantial anatomical structures present limited tracer uptake. Therefore, we constructed and validated strain- and tracer-specific rat brain templates in Paxinos space to allow intra-modal registration. PET [18F]FDG, [11C]flumazenil, [11C]MeDAS, [11C]PK11195 and [11C]raclopride, and SPECT [99mTc]HMPAO brain scans were acquired from healthy male rats. Tracer-specific templates were constructed by averaging the scans, and by spatial normalization to a widely used MRI-based template. The added value of tracer-specific templates was evaluated by quantification of the residual error between original and realigned voxels after random misalignments of the data set. Additionally, the impact of strain differences, disease uptake patterns (focal and diffuse lesion, and the effect of image and template size on the registration errors were explored. Mean registration errors were 0.70 ± 0.32 mm for [18F]FDG (n = 25, 0.23 ± 0.10mm for [11C]flumazenil (n = 13, 0.88 ± 0.20 mm for [11C]MeDAS (n = 15, 0.64 ± 0.28 mm for [11C]PK11195 (n = 19, 0.34 ± 0.15 mm for [11C]raclopride (n = 6, and 0.40 ± 0.13 mm for [99mTc]HMPAO (n = 15. These values were smallest with tracer-specific templates, when compared to the use of [18F]FDG as reference template (p<0.001. Additionally, registration errors were smallest with strain-specific templates (p<0.05, and when images and templates had the same size (p ≤ 0.001. Moreover, highest registration errors were found for the focal lesion group (p<0.005 and the diffuse lesion group (p = n.s.. In the voxel-based analysis, the reported coordinates of the focal lesion model are consistent with the stereotaxic injection procedure. The use of PET/SPECT strain- and tracer

  2. Carbon monoxide kinetics following simulated cigarette smoking

    Energy Technology Data Exchange (ETDEWEB)

    Karnik, A.S. (Wayne State Univ., Detroit, MI); Coin, E.J.

    1980-05-01

    Carbon monoxide kinetics were measured in the blood (% carboxyhemoglobin) and alveolar phase (ppM carbon monoxide) after simulated cigarette smoking. Cigarette smoking was siumlated using the same amount of carbon monoxide that 2R1F cigarettes manufactured by the Tobacco Research Institute would contain. Ten boluses of air containing carbon monoxide equivalent to smoking one cigarette were inhaled by six healthy nonsmoker volunteers. Carbon monoxide in the air phase was measured by an Ecolyzer and carboxyhemoglobin was measured by a CO-Oximeter. The mean rise in alveolar carbon monoxide immediately and 20 min after inhaling the last bolus was 3.3 and 3.1 ppM, respectively (p<.005). The mean rise in carboxyhemoglobin immediately and 20 min after inhalation of the last bolus was 0.8 and 0.5% respectively (P<.005). The changes in carboxyhemoglobin were found to be similar to changes that occur when one cigarette is actually smoked.

  3. Using Multi-Isotope Tracer Methods to Understand the Sources of Nitrate in Aerosols, Fog and River Water in Podocarpus National Forest, Ecuador

    Science.gov (United States)

    Brothers, L. A.; Dominguez, G.; Fabian, P.; Thiemens, M. H.

    2008-12-01

    sulfate and nitrate concentrations in rain and fog water by standard methods to investigate water and nutrient pathways along with data from satellite and ground based remote sensing, observations and numerical models. We hope to pair this with a multi-isotope tracer method and NOAA Hysplit Back trajectories, and satellite imagery for information about the number of fires burning in the region to help identify sources of the high nitrate deposition.

  4. 跟踪界面活动网格法并行程序的性能分析%PERFORMANCE ANALYSIS OF THE TRACER INTERFACES MOVING GRID METHOD PROGRAM

    Institute of Scientific and Technical Information of China (English)

    陈军; 袁国兴; 李晓梅

    2002-01-01

    The scalability and resource requirements analysis can help users to better understand and optimize their parallel programs. Furthermore, the resource requirements of the typical applications can tell the machine designers which machines are suitable for these applications to run at full speed. This paper succeeds our previous work on scalability studies, such as the nearoptimal scaling model, time scalability and efficiency scalability metrics. We use them to analyze the scalability of a typical application, namely, the tracer interfaces moving grid method parallel program. We also provide a method to analyze its resource requirements.All these methods can be used to analyze more applications to understand their performance and requirements.

  5. 4D-SPECT/CT in orthopaedics: a new method of combined quantitative volumetric 3D analysis of SPECT/CT tracer uptake and component position measurements in patients after total knee arthroplasty

    Energy Technology Data Exchange (ETDEWEB)

    Rasch, Helmut; Falkowski, Anna L.; Forrer, Flavio [Kantonsspital Baselland, Institute for Radiology and Nuclear Medicine, Bruderholz (Switzerland); Henckel, Johann [Imperial College London, London (United Kingdom); Hirschmann, Michael T. [Kantonsspital Baselland, Department of Orthopaedic Surgery and Traumatology, Bruderholz (Switzerland)

    2013-09-15

    The purpose was to evaluate the intra- and inter-observer reliability of combined quantitative 3D-volumetric single-photon emission computed tomography (SPECT)/CT analysis including size, intensity and localisation of tracer uptake regions and total knee arthroplasty (TKA) position. Tc-99m-HDP-SPECT/CT of 100 knees after TKA were prospectively analysed. The anatomical areas represented by a previously validated localisation scheme were 3D-volumetrically analysed. The maximum intensity was recorded for each anatomical area. Ratios between the respective value and the mid-shaft of the femur as the reference were calculated. Femoral and tibial TKA position (varus-valgus, flexion-extension, internal rotation- external rotation) were determined on 3D-CT. Two consultant radiologists/nuclear medicine physicians interpreted the SPECT/CTs twice with a 2-week interval. The inter- and intra-observer reliability was determined (ICCs). Kappa values were calculated for the area with the highest tracer uptake between the observers. The measurements of tracer uptake intensity showed excellent inter- and intra-observer reliabilities for all regions (tibia, femur and patella). Only the tibial shaft area showed ICCs <0.89. The kappa values were almost perfect (0.856, p < 0.001; 95 % CI 0.778, 0.922). For measurements of the TKA position, there was strong agreement within and between the readings of the two observers; the ICCs for the orientation of TKA components for inter- and intra-observer reliability were nearly perfect (ICCs >0.84). This combined 3D-volumetric standardised method of analysing the location, size and the intensity of SPECT/CT tracer uptake regions (''hotspots'') and the determination of the TKA position was highly reliable and represents a novel promising approach to biomechanics. (orig.)

  6. Optimization of Treatment Policy for Acute Carbon Monoxide Poisoning

    Directory of Open Access Journals (Sweden)

    R. N. Akalayev

    2012-01-01

    Full Text Available Objective: to evaluate the efficiency of combination use of hyperbaric oxygenation, succinate-containing solutions, and anti-edematous agents in patients with acute carbon monoxide poisoning. Subjects and methods. The results of treatment were analyzed in 32 patients admitted in 2009—2011 for severe acute carbon monoxide poisoning and a Glasgow coma score of 6—8. The patients were divided into 2 groups: 1 patients whose combination therapy involved hyperbaric oxygenation, Succinasol infusions, and L-lysine-aescinate injections; 2 those who received traditional therapy. All the patients underwent complex clinical, laboratory, and neurophysiologic examinations. Results. Just 24 hours after the combination use of Succinasol and L-lysine-aescinate, Group I patients were observed to have substantially reduced lactate, the content of the latter approached the normal value following 48 hours, which was much below the values in the control group. The similar pattern was observed when endogenous intoxication parameters were examined. During the performed therapy, the level of consciousness and that of intellect according to the MMSE and FAB scales were restored more rapidly in the study group patients than in Group 2. Conclusion. The combination use of hyperbaric oxygenation, the succinate-containing solution Succinasol, and the anti-edematous agent L-lysine-aescinate considerably enhances the efficiency of intensive therapy for acute carbon monoxide poisoning. Key words: carbon monoxide, toxic hypoxic encephalopathy, combination therapy, hyperbaric oxygenation, succinic acid, L-lysine-aescinate.

  7. Modeling fluid flow and tracer transport in fractured rock by the effective continuum method%裂隙岩体渗流及污染物迁移模型的数值模拟研究∗

    Institute of Scientific and Technical Information of China (English)

    王笑雨; 张可霓; 李毅

    2015-01-01

    Flow transport in fracture media is different from that in porous media due to anisotropy of fracture rocks.Available methods for treatment of fracture media include discrete fracture and matrix model, dual-continua method,and effective continuum method.Advantages and disadvantages of these methods are presented,and modeling studies for fluid flow and tracer transport in a field site with fractured rock are performed.The site of study is a small island in eastern China.A steady-state flow field with current climate condition is simulated using a simplified conceptual model of the flow system, which submits to mass conservation and Darcy’s Law.Result of the steady-state flow field is then used in further tracer transport simulations.It is found that adsorption is the most significant factor of transport.With higher infiltration,the tracer tends to reach the boundary with lower concentration.Because higher the infiltration,broader the tracer spreads.Accidentally inj ecting tracer near the fracture area may cause serious pollution.Tracer will quickly spread along the fault with boarder plume and higher concentration.In addition,a portion of the tracer will reach the surface.Therefore,it is necessary to pay close attention to water near faults.%裂隙岩体的非均质性使得其渗流问题与传统多孔介质渗流存在本质差别。目前流行的裂隙渗流模型包括:离散裂隙网格模型;双重连续介质模型;等效连续介质模型。介绍上述方法优劣,并以中国东部某岛屿为基础,基于等效连续介质法,建立三维渗流模型以及污染物迁移模型。数值模拟结果显示,污染物被岩体的吸附程度对污染物运移影响巨大;降水入渗量增多会使得水流速度增快,却不会显著提升污染物运移至边界的时间,反而由于其增大了污染物向四周扩散的趋势,致使较少污染物迁移至边界;距断层较近的污染源不仅会导致污染物迅速迁

  8. Carbon monoxide conversion by anaerobic bioreactor sludges

    NARCIS (Netherlands)

    Sipma, J.; Stams, A.J.M.; Lens, P.N.L.; Lettinga, G.

    2003-01-01

    Seven different anaerobic sludges from wastewater treatment reactors were screened for their ability to convert carbon monoxide (CO) at 30 and 55degreesC
    Seven different anaerobic sludges from wastewater treatment reactors were screened for their ability to convert carbon monoxide (CO) at 30 and

  9. TRACER - TRACING AND CONTROL OF ENGINEERING REQUIREMENTS

    Science.gov (United States)

    Turner, P. R.

    1994-01-01

    TRACER (Tracing and Control of Engineering Requirements) is a database/word processing system created to document and maintain the order of both requirements and descriptive material associated with an engineering project. A set of hierarchical documents are normally generated for a project whereby the requirements of the higher level documents levy requirements on the same level or lower level documents. Traditionally, the requirements are handled almost entirely by manual paper methods. The problem with a typical paper system, however, is that requirements written and changed continuously in different areas lead to misunderstandings and noncompliance. The purpose of TRACER is to automate the capture, tracing, reviewing, and managing of requirements for an engineering project. The engineering project still requires communications, negotiations, interactions, and iterations among people and organizations, but TRACER promotes succinct and precise identification and treatment of real requirements separate from the descriptive prose in a document. TRACER permits the documentation of an engineering project's requirements and progress in a logical, controllable, traceable manner. TRACER's attributes include the presentation of current requirements and status from any linked computer terminal and the ability to differentiate headers and descriptive material from the requirements. Related requirements can be linked and traced. The program also enables portions of documents to be printed, individual approval and release of requirements, and the tracing of requirements down into the equipment specification. Requirement "links" can be made "pending" and invisible to others until the pending link is made "binding". Individuals affected by linked requirements can be notified of significant changes with acknowledgement of the changes required. An unlimited number of documents can be created for a project and an ASCII import feature permits existing documents to be incorporated

  10. TRACER - TRACING AND CONTROL OF ENGINEERING REQUIREMENTS

    Science.gov (United States)

    Turner, P. R.

    1994-01-01

    TRACER (Tracing and Control of Engineering Requirements) is a database/word processing system created to document and maintain the order of both requirements and descriptive material associated with an engineering project. A set of hierarchical documents are normally generated for a project whereby the requirements of the higher level documents levy requirements on the same level or lower level documents. Traditionally, the requirements are handled almost entirely by manual paper methods. The problem with a typical paper system, however, is that requirements written and changed continuously in different areas lead to misunderstandings and noncompliance. The purpose of TRACER is to automate the capture, tracing, reviewing, and managing of requirements for an engineering project. The engineering project still requires communications, negotiations, interactions, and iterations among people and organizations, but TRACER promotes succinct and precise identification and treatment of real requirements separate from the descriptive prose in a document. TRACER permits the documentation of an engineering project's requirements and progress in a logical, controllable, traceable manner. TRACER's attributes include the presentation of current requirements and status from any linked computer terminal and the ability to differentiate headers and descriptive material from the requirements. Related requirements can be linked and traced. The program also enables portions of documents to be printed, individual approval and release of requirements, and the tracing of requirements down into the equipment specification. Requirement "links" can be made "pending" and invisible to others until the pending link is made "binding". Individuals affected by linked requirements can be notified of significant changes with acknowledgement of the changes required. An unlimited number of documents can be created for a project and an ASCII import feature permits existing documents to be incorporated

  11. Enhanced Oil Recovery: Aqueous Flow Tracer Measurement

    Energy Technology Data Exchange (ETDEWEB)

    Joseph Rovani; John Schabron

    2009-02-01

    A low detection limit analytical method was developed to measure a suite of benzoic acid and fluorinated benzoic acid compounds intended for use as tracers for enhanced oil recovery operations. Although the new high performance liquid chromatography separation successfully measured the tracers in an aqueous matrix at low part per billion levels, the low detection limits could not be achieved in oil field water due to interference problems with the hydrocarbon-saturated water using the system's UV detector. Commercial instrument vendors were contacted in an effort to determine if mass spectrometry could be used as an alternate detection technique. The results of their work demonstrate that low part per billion analysis of the tracer compounds in oil field water could be achieved using ultra performance liquid chromatography mass spectrometry.

  12. Development of radioisotope tracer technology

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Joon Ha; Lee, Myun Joo; Jung, Sung Hee; Park, Soon Chul; Lim, Dong Soon; Kim, Jae Ho; Lee, Jae Choon; Lee, Doo Sung; Cho, Yong Suk; Shin, Sung Kuan

    2000-04-01

    The purpose of this study is to develop the radioisotope tracer technology, which can be used in solving industrial and environmental problems and to build a strong tracer group to support the local industries. In relation to the tracer technology in 1999, experiments to estimate the efficiencies of a sludge digester of a waste water treatment plant and a submerged biological reactor of a dye industry were conducted. As a result, the tracer technology for optimization of facilities related to wastewater treatment has been developed and is believed to contribute to improve their operation efficiency. The quantification of the experimental result was attempted to improve the confidence of tracer technology by ECRIN program which basically uses the MCNP simulation principle. Using thin layer activation technique, wear of tappet shim was estimated. Thin layer surface of a tappet shim was irradiated by proton beam and the correlation between the measured activity loss and the amount of wear was established. The equipment was developed to adjust the energy of proton which collides with the surface of tappet. The tracer project team has participated into the tracer test for estimating the efficiency of RFCC system in SK cooperation. From the experiment the tracer team has obtained the primary elements to be considered for judging the efficiency of RFCC unit. By developing the tracer techniques to test huge industrial units like RFCC, the tracer team will be able to support the local industries that require technical services to solve any urgent trouble. (author)

  13. The Carbon Monoxide Tape Recorder

    Science.gov (United States)

    Schoeberl, M. R.; Duncan, B. N.; Douglass, A. R.; Waters, J.; Livesey, N.; Read, W.; Filipiak, M.

    2006-01-01

    Using Aura MLS data we have identified the stratospheric tape recorder in carbon monoxide (CO). Unlike the water vapor tape recorder, which is controlled by upper troposphere processes, the CO tape recorder is linked to seasonal biomass burning. Since CO has a lifetime of only a few months, the CO tape recorder barely extends above 20 km. The tape head for CO appears to be close to 360K near the same location as the water vapor tape head [Read et al, 20041. Both tape heads are below the equatorial cold point tropopause but above the base of the tropical tropopause layer. The tape recorder signal becomes more distinct from 360K to 380K suggesting that convective detrainment of plays a decreasingly important role with altitude. The Global Modeling Initiative chemical transport model forced by the climatology of biomass burning reproduces the CO tape recorder.

  14. IR band of O2 at 1.27 μm as the tracer of O3 in the mesosphere and lower thermosphere: Correction of the method

    Science.gov (United States)

    Martyshenko, K. V.; Yankovsky, V. A.

    2017-03-01

    The problem of systematic overestimation (20-50%) of the retrieved ozone concentrations in the altitude range of 60-80 km in the TIMED-SABER satellite experiment in the daytime has been solved. The reason for overestimation is the neglect of the electronic vibrational kinetics of photolysis products of ozone and molecular oxygen O2(b1Σg +, ν) and O2(a1Δg, ν). The IR emission band of O2(a1Δg, ν = 0) at 1.27 μm can be correctly used in remote sensing in order to obtain the ozone altitude profile in the altitude range of 50-88 km only with the use of a complete model of electronic vibrational kinetics of O2 and O3 photolysis products (YM2011) in the Earth's mesosphere and lower thermosphere. Alternative ozone tracers have been considered, and an optimum tracer in the altitude range of 50-100 km such as O2(b1Σg +, ν = 1) molecule emissions has been proposed.

  15. Effect of preparation method on the surface characteristics and activity of the Pd/OMS-2 catalysts for the oxidation of carbon monoxide, toluene, and ethyl acetate

    Science.gov (United States)

    Liu, Lisha; Song, Yong; Fu, Zhidan; Ye, Qing; Cheng, Shuiyuan; Kang, Tianfang; Dai, Hongxing

    2017-02-01

    The cryptomelane-type manganese oxide octahedral molecular sieve (OMS-2)-supported Pd (0.5 wt% Pd/OMS-2-DP, 0.5 wt% Pd/OMS-2-PI, and 0.5 wt% Pd/OMS-2-EX) catalysts were prepared by the deposition-precipitation, pre-incorporation, and ion-exchanging strategies, respectively. It is shown that the preparation method exerted an important effect on the physicochemical property of the sample. Among the OMS-2-supported Pd catalysts, 0.5 wt% Pd/OMS-2-DP possessed the highest surface (Mn2+ + Mn3+)/Mn4+ atomic ratio and the highest surface Pd loading and acid sites. The 0.5 wt% Pd/OMS-2 catalysts outperformed the Pd-free counterpart, among which 0.5 wt% Pd/OMS-2-DP presented the best catalytic activity (T50% and T90% were 25 and 55 °C for CO oxidation, 240 and 285 °C for toluene oxidation, and 160 and 200 °C for ethyl acetate oxidation, respectively). We believe that the high Pd surface loading, high surface atomic ratio of (Mn2+ + Mn3+)/Mn4+, and good low-temperature reducibility, good oxygen mobility, and high acidity were responsible for the excellent performance of the 0.5 wt% Pd/OMS-2-DP catalyst.

  16. The Accurate Particle Tracer Code

    CERN Document Server

    Wang, Yulei; Qin, Hong; Yu, Zhi

    2016-01-01

    The Accurate Particle Tracer (APT) code is designed for large-scale particle simulations on dynamical systems. Based on a large variety of advanced geometric algorithms, APT possesses long-term numerical accuracy and stability, which are critical for solving multi-scale and non-linear problems. Under the well-designed integrated and modularized framework, APT serves as a universal platform for researchers from different fields, such as plasma physics, accelerator physics, space science, fusion energy research, computational mathematics, software engineering, and high-performance computation. The APT code consists of seven main modules, including the I/O module, the initialization module, the particle pusher module, the parallelization module, the field configuration module, the external force-field module, and the extendible module. The I/O module, supported by Lua and Hdf5 projects, provides a user-friendly interface for both numerical simulation and data analysis. A series of new geometric numerical methods...

  17. Delayed encephalopathy after acute carbon monoxide poisoning

    Directory of Open Access Journals (Sweden)

    Mehmet İbrahim Turan

    2014-03-01

    Full Text Available Carbon monoxide poisoning is a major cause of death following attempted suicide and accidental exposures. Although clinical presentation depends on the duration and the intensity of exposure, the assessment of the severity of intoxication is difficult. A small percentage of patients who show complete initial recovery may develop delayed neurological deficits. Delayed encephalopathy after acute carbon monoxide poisoning is a rare and poor prognosis neurologic disorders and there is no specific treatment. We present a case with early onset of delayed encephalopathy after acute carbon monoxide poisoning with typical cranial imaging findings in a child with atypical history and clinical presentation.

  18. Travel-time-based thermal tracer tomography

    Science.gov (United States)

    Somogyvári, Márk; Bayer, Peter; Brauchler, Ralf

    2016-05-01

    Active thermal tracer testing is a technique to get information about the flow and transport properties of an aquifer. In this paper we propose an innovative methodology using active thermal tracers in a tomographic setup to reconstruct cross-well hydraulic conductivity profiles. This is facilitated by assuming that the propagation of the injected thermal tracer is mainly controlled by advection. To reduce the effects of density and viscosity changes and thermal diffusion, early-time diagnostics are used and specific travel times of the tracer breakthrough curves are extracted. These travel times are inverted with an eikonal solver using the staggered grid method to reduce constraints from the pre-defined grid geometry and to improve the resolution. Finally, non-reliable pixels are removed from the derived hydraulic conductivity tomograms. The method is applied to successfully reconstruct cross-well profiles as well as a 3-D block of a high-resolution fluvio-aeolian aquifer analog data set. Sensitivity analysis reveals a negligible role of the injection temperature, but more attention has to be drawn to other technical parameters such as the injection rate. This is investigated in more detail through model-based testing using diverse hydraulic and thermal conditions in order to delineate the feasible range of applications for the new tomographic approach.

  19. The Range of 1-3 keV Electrons in Solid Oxygen and Carbon Monoxide

    DEFF Research Database (Denmark)

    Oehlenschlæger, M.; Andersen, H.H.; Schou, Jørgen

    1985-01-01

    The range of 1-3 keV electrons in films of solid oxygen and carbon monoxide has been measured by a mirror substrate method. The technique used here is identical to the one previously used for range measurements in solid hydrogen and nitrogen. The range in oxygen is slightly shorter than...... that in nitrogen whereas the range in carbon monoxide is about 20% larger than that in the nitrogen....

  20. Pregnancy Hypertenssion and Preeclampsia in Enviromental Expossure to Carbon Monoxide

    OpenAIRE

    2008-01-01

    Introduction: In this study relationship between carbon monoxide (CO) with pregnancy induced hypertension and preeclampsia in mothers in various levels of CO pollution was evaluated. Methods: The study was carried out in three teaching hospitals and 4500 pregnant women living area divided in one low-level CO polluted and as the second level, three moderate to high polluted areas (central, south and west). The subjects, residence places were within 5 kilometers of the air pollution monitoring ...

  1. Radon as geological tracer

    Energy Technology Data Exchange (ETDEWEB)

    Lacerda, T.; Anjos, R.M. [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Inst. de Fisica; Valladares, D.L.; Rizzotto, M.; Velasco, H.; Ayub, J. Juri [Universidad Nacional de San Luis (Argentina). Inst. de Matematica Aplicada San Luis (IMASL); Silva, A.A.R. da; Yoshimura, E.M. [Universidade de Sao Paulo (IF/USP), SP (Brazil). Inst. de Fisica

    2012-07-01

    Full text: This work presents measurements of {sup 222}Rn levels performed in La Carolina gold mine and Los Condores tungsten mine at the province of San Luis, Argentina, today used for tourist visitation, and can evaluate the potential use of such radioactive noble gas as tracer or marker for geological processes in underground environments. By concentrations of {sup 40}K, {sup 232}Th and {sup 23}'8U were also measured in the walls of tunnels were determined the rocks mineral composition, what indicated that the mines have the same composition. In this sense, we used nuclear trace plastic detectors CR-39, gamma spectrometry of rock samples and Geiger-Muller (GM) monitors The patterns of radon gas transportation processes revealed that La Carolina could be interpreted through a model based on a radioactive gas confined into a single entrance tube, with constant cross section and air velocity. Los Condores, which has a second main entrance, could be interpreted through a model based on a radioactive gas confined into a two entrance tube, allowing a chimney effect for air circulation. The results showed the high potential of using {sup 222}Rn as a geological tracer. In what concerns the occupational hazard, in summer (time of more intense tourist activity in the mine) La Carolina presented a mean concentration of the radioactive noble gas that exceeds in four times the action level of 1,5 kBq m{sup -3} recommended by the International Commission of Radiological Protection (ICRP). The chimney effect shows the low mean concentration of radon in Los Condores. (author)

  2. Exotic tracers for atmospheric studies

    Energy Technology Data Exchange (ETDEWEB)

    Lovelock, J.E. (Brazzos Ltd., Launceston (UK)); Ferber, G.J. (National Oceanic and Atmospheric Administration, Silver Spring, MD (USA). Air Resources Lab.)

    1982-01-01

    Tracer materials can be injected into the atmosphere to study transport and dispersion processes and to validate air pollution model calculations. Tracers should be inert, non-toxic and harmless to the environment. Tracers for long-range experiments, where dilution is very great, must be measurable at extremely low concentrations, well below the parts per trillion level. Compounds suitable for long-range tracer work are rare and efforts should be made to reserve them for meteorological studies, barring them from commercial uses which would increase atmospheric background concentrations. The use of these exotic tracers, including certain perfluorocarbons and isotopically labelled methanes, should be coordinated within the meteorological community to minimize interferences and maximise research benefits.

  3. Exotic tracers for atmospheric studies

    Science.gov (United States)

    Lovelock, James E.; Ferber, Gilbert J.

    Tracer materials can be injected into the atmosphere to study transport and dispersion processes and to validate air pollution model calculations. Tracers should be inert, non-toxic and harmless to the environment. Tracers for long-range experiments, where dilution is very great, must be measurable at extremely low concentrations, well below the parts per trillion level. Compounds suitable for long-range tracer work are rare and efforts should be made to reserve them for meteorological studies, barring them from commercial uses which would increase atmospheric background concentrations. The use of these exotic tracers, including certain perfluorocarbons and isotopically labelled methanes, should be coordinated within the meteorological community to minimize interferences and maximize research benefits.

  4. Carbon Monoxide Silicate Reduction System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Carbon Monoxide Silicate Reduction System (COSRS) is a novel technology for producing large quantities of oxygen on the Moon. Oxygen yields of 15 kilograms per...

  5. Protect Yourself from Carbon Monoxide Poisoning

    Centers for Disease Control (CDC) Podcasts

    2007-11-20

    Learn about carbon monoxide - a colorless, odorless gas - and how to protect yourself and your family.  Created: 11/20/2007 by CDC National Center for Environmental Health.   Date Released: 12/4/2007.

  6. Integrated electricity and carbon monoxide production

    Energy Technology Data Exchange (ETDEWEB)

    Griffiths, J.

    1994-03-23

    In a process for the production of carbon monoxide and electric power in an IGCC with the removal of sulphur compounds, between the outlet of quenched gas from a partial oxidation unit and a fuel inlet to a combined cycle gas turbine there is a permeable membrane unit to separate a non-permeable stream, which is utilised as a source of carbon monoxide, and a permeate stream, which is used as fuel for the gas turbine of the combined cycle unit. (author)

  7. Hearing Loss due to Carbon Monoxide Poisoning

    Directory of Open Access Journals (Sweden)

    Amir Houshang Mehrparvar

    2013-01-01

    Full Text Available Carbon monoxide poisoning is one of the rare causes of hearing loss which may cause reversible or irreversible, unilateral or bilateral hearing loss after acute or chronic exposure. In this report, we present a case of bilateral sensorineural hearing loss in a secondary smelting workshop worker after an acute exposure to carbon monoxide. This complication was diagnosed by pure-tone audiometry and confirmed by transient evoked otoacoustic emissions. Hearing loss has not improved after 3 months of followup.

  8. Suitability of tracers; Eignung von Tracern

    Energy Technology Data Exchange (ETDEWEB)

    Klotz, D. [GSF - Forschungszentrum fuer Umwelt und Gesundheit GmbH, Neuherberg (Germany). Inst. fuer Hydrologie

    1999-02-01

    Hydrological tracer techniques are a means of making statements on the direction and speed of underground water. One of the simpler tasks is to find out whether there is hydrological communication between two given points. This requires a determination of the direction of flow, which places less exacting demands on the properties of the tracer than does the task of determining the flow velocity of underground water. Tracer methods can serve to infer from flow velocity the distance (flow) velocity, which is defined as the ratio between the distance between two points located in flow direction and the actual time it takes water to flow from one to the other. [Deutsch] Mit Hilfe der hydrologischen Markierungstechniken koennen Aussagen ueber die Richtung und die Geschwindigkeit von Bewegungen des unterirdischen Wassers gemacht werden. Der einfachere Fall liegt vor, wenn festgestellt werden soll, ob zwischen zwei Punkten eine hydrologische Verbindung besteht. Bei dieser Fliessrichtungsbestimmung sind die Forderungen an die Eigenschaften der einzusetzenden Tracer geringer als bei der Bestimmung der Geschwindigkeit des unterirdischen Wassers. Von den Geschwindigkeiten des unterirdischen Wassers ist die Abstands-(Fliess)geschwindigkeit, die definiert ist durch das Verhaeltnis aus dem Abstand und der wahren Fliesszeit zwischen zwei in Bewegungsrichtung gelegenen Punkten, durch Tracermethoden zu bestimmen. (orig.)

  9. Laplace transform in tracer kinetic modeling

    Energy Technology Data Exchange (ETDEWEB)

    Hauser, Eliete B., E-mail: eliete@pucrs.br [Instituto do Cerebro (InsCer/FAMAT/PUC-RS), Porto Alegre, RS, (Brazil). Faculdade de Matematica

    2013-07-01

    The main objective this paper is to quantify the pharmacokinetic processes: absorption, distribution and elimination of radiopharmaceutical(tracer), using Laplace transform method. When the drug is administered intravenously absorption is complete and is available in the bloodstream to be distributed throughout the whole body in all tissues and fluids, and to be eliminated. Mathematical modeling seeks to describe the processes of distribution and elimination through compartments, where distinct pools of tracer (spatial location or chemical state) are assigned to different compartments. A compartment model is described by a system of differential equations, where each equation represents the sum of all the transfer rates to and from a specific compartment. In this work a two-tissue irreversible compartment model is used for description of tracer, [{sup 18}F]2-fluor-2deoxy-D-glucose. In order to determine the parameters of the model, it is necessary to have information about the tracer delivery in the form of an input function representing the time-course of tracer concentration in arterial blood or plasma. We estimate the arterial input function in two stages and apply the Levenberg-Marquardt Method to solve nonlinear regressions. The transport of FDG across de arterial blood is very fast in the first ten minutes and then decreases slowly. We use de Heaviside function to represent this situation and this is the main contribution of this study. We apply the Laplace transform and the analytical solution for two-tissue irreversible compartment model is obtained. The only approach is to determinate de arterial input function. (author)

  10. Development of new heterogeneous catalysts for the decomposition of methanol into hydrogen and carbon monoxide applying high throughput methods; Entwicklung neuer heterogener Katalysatoren zur Spaltung von Methanol in Wasserstoff und Kohlenmonoxid mittels Hochdurchsatz-Methoden

    Energy Technology Data Exchange (ETDEWEB)

    Weiss, Torsten

    2008-07-11

    The topic of this thesis has been the development of new heterogeneous catalysts for the decomposition of methanol into hydrogen and carbon monoxide. As an important constraint here, the content of noble metals of the catalysts should be as low as possible. High-throughput-methods were applied in some of the syntheses and experiments to accelerate the development, as, for example, the use of liquid based sol-gel syntheses and the examination of catalyst libraries by spatial resolution gas chromatography. This screening technique allowed to test up to 207 different substances during one single experiment. Then, different combinatorial strategies were applied. First, these methods led to a highly active and stable catalyst in the ternary system of Cu-Ni-Zn, which showed high conversion and selectivity comparable to an industrial reference catalyst. Its activity during an 18 hour long term run was constant in contrast to the reference. Second, an additional approach starting from a broader variety of elements led to a Ce- Ru- and to a Cr-Ru-catalyst. Both of them were highly active in short term experiments, but lost their outstanding performances during long term runs. (orig.) [German] Die vorliegende Arbeit befasste sich mit der Entwicklung neuer heterogener Katalysatoren fuer die Spaltung von Methanol zu Wasserstoff und Kohlenmonoxid, die einen moeglichst geringen Gehalt an Edelmetallen aufweisen sollten. Um diesen Prozess zu beschleunigen, wurden in einem Teil der Synthesen und Experimente Hochdurchsatzmethoden verwendet. Neben der Roboter gestuetzten Sol-Gel-Synthese umfasste dies die Untersuchung von Katalysatorbibliotheken mittels ortsaufgeloester Gaschromatographie, die es ermoeglichte, in einem Experiment bis zu 207 verschiedene Substanzen auf ihre katalytische Aktivitaet zu testen. Unter Anwendung verschiedener kombinatorischer Strategien wurde zunaechst ein sehr aktiver und stabiler Katalysator im ternaeren Cu-Ni-Zn-System entdeckt. Neben Umsaetzen und

  11. Tracer injection techniques in flowing surface water

    Science.gov (United States)

    Wörman, A.

    2009-04-01

    Residence time distributions for flowing water and reactive matter are commonly used integrated properties of the transport process for determining technical issues of water resource management and in eco-hydrological science. Two general issues for tracer techniques are that the concentration-vs-time relation following a tracer injection (the breakthrough curve) gives unique transport information in different parts of the curve and separation of hydromechanical and reactive mechanisms often require simultaneous tracer injections. This presentation discusses evaluation methods for simultaneous tracer injections based on examples of tracer experiments in small rivers, streams and wetlands. Tritiated water is used as a practically inert substance to reflect the actual hydrodynamics, but other involved tracers are Cr(III)-51, P-32 and N-15. Hydromechanical, in-stream dispersion is reflected as a symmetrical spreading of the spatial concentration distribution. This requires that the transport distance over water depth is larger than about five times the flow Peclet number. Transversal retention of both inert and reactive solutes is reflected in terms of the tail of the breakthrough curve. Especially, reactive solutes can have a substantial magnification of the tailing behaviour depending on reaction rates or partitioning coefficients. To accurately discriminate between the effects of reactions and hydromechanical mixing its is relevant to use simultaneous injections of inert and reactive tracers with a sequential or integrated evaluation procedure. As an example, the slope of the P-32 tailing is consistently smaller than that of a simultaneous tritium injection in Ekeby wetland, Eskilstuna. The same applies to N-15 injected in the same experiment, but nitrogen is affected also by a systematic loss due to denitrification. Uptake in stream-bed sediments can be caused by a pumping effect arising when a variable pressure field is created on the stream bottom due to bed

  12. Utility of the Measurement of Carboxyhemoglobin Level at the Site of Acute Carbon Monoxide Poisoning in Rural Areas

    Directory of Open Access Journals (Sweden)

    Makoto Onodera

    2016-01-01

    Full Text Available Objective. This study examined the hypothesis that correlations exist between the carbon monoxide exposure time and the carboxyhemoglobin concentration at the site of carbon monoxide poisoning, using a pulse carbon monoxide oximeter in rural areas or the carboxyhemoglobin concentration measured at a given medical institution. Background. In previous studies, no definitive relationships between the arterial blood carboxyhemoglobin level and the severity of carbon monoxide poisoning have been observed. Method. The subjects included patients treated for acute carbon monoxide poisoning in whom a medical emergency team was able to measure the carboxyhemoglobin level at the site of poisoning. We examined the relationship between the carboxyhemoglobin level at the site of poisoning and carbon monoxide exposure time and the relationships between the arterial blood carboxyhemoglobin level and carbon monoxide exposure time. Results. A total of 10 patients met the above criteria. The carboxyhemoglobin levels at the site of poisoning were significantly and positively correlated with the exposure time (rs = 0.710, p=0.021, but the arterial blood carboxyhemoglobin levels were not correlated with the exposure time. Conclusion. In rural areas, the carboxyhemoglobin level measured at the site of carbon monoxide poisoning correlated with the exposure time.

  13. Use of a time-domain electromagnetic method with geochemical tracers to explore the salinity anomalies in a small coastal aquifer in north-eastern Tunisia

    Science.gov (United States)

    Chekirbane, Anis; Tsujimura, Maki; Kawachi, Atsushi; Lachaal, Fethi; Isoda, Hiroko; Tarhouni, Jamila

    2014-12-01

    The study area is a small coastal plain in north-eastern Tunisia. It is drained by an ephemeral stream network and is subject to several pollutant discharges such as oilfield brine coming from a neighboring oil company and wastewater from Somâa city, located in the upstream of the plain. Furthermore, a hydraulic head near the coastal part of the aquifer is below sea level, suggesting that seawater intrusion may occur. A time-domain electromagnetic (TDEM) survey, based on 28 soundings, was conducted in Wadi Al Ayn and Daroufa plains to delineate the saline groundwater. Based on longitudinal and transversal resistivity two-dimensional pseudosections calibrated with boring data, the extent of saline water was identified. Geochemical tracers were combined with the resistivity dataset to differentiate the origin of groundwater salinization. In the upstream part of the plain, the infiltration of oilfield brine through the sandy bed of Wadi Al Ayn seems to have a considerable effect on groundwater salinization. However, in the coastal part of the aquifer, groundwater salinization is due to seawater intrusion and the saltwater is reaching an inland extent around 1.3 km from the shoreline. The contribution ratios of saline water bodies derived from the inverted chloride data vary for the oilfield brine from 1 to 13 % and for the seawater from 2 to 21 %.

  14. Halon-1301, a new Groundwater Age Tracer

    Science.gov (United States)

    Beyer, Monique; van der Raaij, Rob; Morgenstern, Uwe; Jackson, Bethanna

    2015-04-01

    Groundwater dating is an important tool to assess groundwater resources in regards to direction and time scale of groundwater flow and recharge and to assess contamination risks and manage remediation. To infer groundwater age information, a combination of different environmental tracers, such as tritium and SF6, are commonly used. However ambiguous age interpretations are often faced, due to a limited set of available tracers and limitations of each tracer method when applied alone. There is a need for additional, complementary groundwater age tracers. We recently discovered that Halon-1301, a water soluble and entirely anthropogenic gaseous substance, may be a promising candidate [Beyer et al, 2014]. Halon-1301 can be determined along with SF6, SF5CF3 and CFC-12 in groundwater using a gas chromatography setup with attached electron capture detector developed by Busenberg and Plummer [2008]. Halon-1301 has not been assessed in groundwater. This study assesses the behaviour of Halon-1301 in water and its suitability as a groundwater age tracer. We determined Halon-1301 in 17 groundwater and various modern (river) waters sites located in 3 different groundwater systems in the Wellington Region, New Zealand. These waters have been previously dated with tritium, CFC-12, CFC-11 and SF6 with mean residence times ranging from 0.5 to over 100 years. The waters range from oxic to anoxic and some show evidence of CFC contamination or degradation. This allows us to assess the different properties affecting the suitability of Halon-1301 as groundwater age tracer, such as its conservativeness in water and local contamination potential. The samples are analysed for Halon-1301 and SF6simultaneously, which allows identification of issues commonly faced when using gaseous tracers such as contamination with modern air during sampling. Overall we found in the assessed groundwater samples Halon-1301 is a feasible new groundwater tracer. No sample indicated significantly elevated

  15. First-Principles Investigations on Europium Monoxide

    KAUST Repository

    Wang, Hao

    2011-05-01

    Europium monoxide is both an insulator and a Heisenberg ferromagnet (Tc=69 K). In the present thesis, the author has investigated the electronic structure of different types of EuO by density functional theory. The on-site Coulomb interaction of the localized Eu 4f and 5d electrons, which is wrongly treated in the standard generalized gradient approximation method, is found to be crucial to obtain the correct insulating ground state as observed in experiments. Our results show that the ferromagnetism is stable under pressure, both hydrostatic and uniaxial. For both types of pressure an insulator-metal transition is demonstrated. Moreover, the experimentally observed insulator-metal transition in oxygen deficient and gadolinium-doped EuO is reproduced in our calculations for impurity concentrations of 6.25% and 25%. Furthermore, a 10- layer EuO thin film is theoretically predicted to be an insulator with a narrow band gap of around 0.08 eV, while the Si/EuO interface shows metallic properties with the Si and O 2p as well as Eu 5d bands crossing the Fermi level.

  16. Laboratory Testing of Magnetic Tracers for Soil Erosion Measurement*1

    Institute of Scientific and Technical Information of China (English)

    HU Guo-Qing; DONG Yuan-Jie; WANG Hui; QIU Xian-Kui; WANG Yan-Hua

    2011-01-01

    Soil erosion, which includes soil detachment, transport, and deposition, is one of the important dynamic land surface processes. The magnetic tracer method is a useful method for studying soil erosion processes. In this study, five types of magnetic tracers were made with fine soil, fly ash, cement, bentonite, and magnetic powder (reduced iron powder) using the method of disk granulation. The tracers were uniformly mixed with soil and tested in the laboratory using simulated rainfall and inflow experiments to simulate the interrill and rill components of soil erosion, in order to select one or more tracers which could be used to study detachment and deposition by the erosive forces of raindrops and surface flow of water on a slope. The results showed that the five types of magnetic tracers with high magnetic susceptibility and a wide range of sizes had a range of 0.99-1.29 gcm-s in bulk density. In the interrill and rill experiments, the tracers FC1 and FC2 which consisted of fly ash and cement at ratios of 1:1 and 2:1, respectively, were transported in phase with soil particles since the magnetic susceptibility of sediment approximated that of the soil which was uneroded and the slopes of the regression equations between the detachment of sediment and magnetic tracers FC1 and FC2 were very close to the expected value of 20, which was the original soil/tracer ratio. The detachment and deposition on slopes could be accurately reflected by the magnetic susceptibility differences. The change in magnetic susceptibility depended on whether deposition or detachment occurred. However, the tracer FS which consisted of fine soil and the tracers FB1 and FB2 which consisted of fly ash and bentonite at ratios of 1:1 and 2:1, respectively, were all unsuitable for soil erosion study since there was no consistent relationship between sediment and tracer detachment for increasing amounts of runoff. Therefore, the tracers FC1 and FC2 could be used to study soil erosion by water.

  17. PENTACARBON DIOXIDE (C{sub 5}O{sub 2}) FORMATION AND ITS ROLE AS A TRACER OF SOLAR SYSTEM EVOLUTION

    Energy Technology Data Exchange (ETDEWEB)

    Förstel, Marko; Maksyutenko, Pavlo; Kaiser, Ralf I. [W. M. Keck Research Laboratory in Astrochemistry, University of Hawaii at Manoa, Honolulu, Hawaii, HI 96822 (United States); Mebel, Alexander M., E-mail: ralfk@hawaii.edu [Department of Chemistry and Biochemistry, Florida International University, 11200 SW 8th Street, Miami, FL 33193 (United States)

    2016-02-20

    Carbon monoxide is the second most abundant molecule on icy grains in the interstellar medium. These grains are under the influence of ionizing radiation, which induces the chemical reaction within the ice. Here we report the first observation of subliming pentacarbon dioxide (C{sub 5}O{sub 2}) after irradiation of pure carbon monoxide ice with energetic electrons. Our results show that pentacarbon dioxide is a stable reaction product in a carbon monoxide matrix that survives the sublimation in star-forming regions at sublimation temperatures of 175 K. Along with carbon suboxide (C{sub 3}O{sub 2}), this molecule can serve as a powerful tracer of the temperature history of formerly carbon monoxide rich ices in molecular clouds and star-forming regions.

  18. Tracer technology modeling the flow of fluids

    CERN Document Server

    Levenspiel, Octave

    2012-01-01

    A vessel’s behavior as a heat exchanger, absorber, reactor, or other process unit is dependent upon how fluid flows through the vessel.  In early engineering, the designer would assume either plug flow or mixed flow of the fluid through the vessel.  However, these assumptions were oftentimes inaccurate, sometimes being off by a volume factor of 100 or more.  The result of this unreliable figure produced ineffective products in multiple reaction systems.   Written by a pioneering researcher in the field of chemical engineering, the tracer method was introduced to provide more accurate flow data.  First, the tracer method measured the actual flow of fluid through a vessel.  Second, it developed a suitable model to represent the flow in question.  Such models are used to follow the flow of fluid in chemical reactors and other process units, like in rivers and streams, or solid and porous structures.  In medicine, the tracer method is used to study the flow of chemicals—harmful  and harmless—in the...

  19. Driven tracers in narrow channels

    Science.gov (United States)

    Cividini, J.; Mukamel, D.; Posch, H. A.

    2017-01-01

    Steady-state properties of a driven tracer moving in a narrow two-dimensional (2D) channel of quiescent medium are studied. The tracer drives the system out of equilibrium, perturbs the density and pressure fields, and gives the bath particles a nonzero average velocity, creating a current in the channel. Three models in which the confining effect of the channel is probed are analyzed and compared in this study: the first is the simple symmetric exclusion process (SSEP), for which the stationary density profile and the pressure on the walls in the frame of the tracer are computed. We show that the tracer acts like a dipolar source in an average velocity field. The spatial structure of this 2D strip is then simplified to a one-dimensional (1D) SSEP, in which exchanges of position between the tracer and the bath particles are allowed. Using a combination of mean-field theory and exact solution in the limit where no exchange is allowed gives good predictions of the velocity of the tracer and the density field. Finally, we show that results obtained for the 1D SSEP with exchanges also apply to a gas of overdamped hard disks in a narrow channel. The correspondence between the parameters of the SSEP and of the gas of hard disks is systematic and follows from simple intuitive arguments. Our analytical results are checked numerically.

  20. Probing into the aging dynamics of biomass burning aerosol by using satellite measurements of aerosol optical depth and carbon monoxide

    Science.gov (United States)

    Konovalov, Igor B.; Beekmann, Matthias; Berezin, Evgeny V.; Formenti, Paola; Andreae, Meinrat O.

    2017-04-01

    Carbonaceous aerosol released into the atmosphere from open biomass burning (BB) is known to undergo considerable chemical and physical transformations (aging). However, there is substantial controversy about the nature and observable effects of these transformations. A shortage of consistent observational evidence on BB aerosol aging processes under different environmental conditions and at various temporal scales hinders development of their adequate representations in chemistry transport models (CTMs). In this study, we obtain insights into the BB aerosol dynamics by using available satellite measurements of aerosol optical depth (AOD) and carbon monoxide (CO). The basic concept of our method is to consider AOD as a function of the BB aerosol photochemical age (that is, the time period characterizing the exposure of BB aerosol emissions to atmospheric oxidation reactions) predicted by means of model tracers. We evaluate the AOD enhancement ratio (ER) defined as the ratio of optical depth of actual BB aerosol with respect to that of a modeled aerosol tracer that is assumed to originate from the same fires as the real BB aerosol but that is not affected by any aging processes. To limit possible effects of model transport errors, the AOD measurements are normalized to CO column amounts that are also retrieved from satellite measurements. The method is applied to the analysis of the meso- and synoptic-scale evolution of aerosol in smoke plumes from major wildfires that occurred in Siberia in summer 2012. AOD and CO retrievals from MODIS and IASI measurements, respectively, are used in combination with simulations performed with the CHIMERE CTM. The analysis indicates that aging processes strongly affected the evolution of BB aerosol in the situation considered, especially in dense plumes (with spatial average PM2. 5 concentration exceeding 100 µg m-3). For such plumes, the ER is found to increase almost 2-fold on the scale of ˜ 10 h of daytime aerosol evolution

  1. Determination of stream reaeration coefficients by use of tracers

    Science.gov (United States)

    Kilpatrick, F.A.; Rathbun, R.E.; Yotsukura, Nobuhiro; Parker, G.W.; DeLong, L.L.

    1989-01-01

    Stream reaeration is the physical absorption of oxygen from the atmosphere by a flowing stream. This is the primary process by which a stream replenishes the oxygen consumed in the biodegradation of organic wastes. Prior to 1965, reaeration rate coefficients could be estimated only by indirect methods. In 1965, a direct method of measuring stream reaeration coefficients was developed whereby a radioactive tracer gas was injected into a stream-the principle being that the tracer gas would be desorbed from the stream inversely to how oxygen would be absorbed. The technique has since been modified by substituting hydrocarbon gases for the radioactive tracer gas. This manual describes the slug-injection and constant-rate-injection methods of measuring gas-tracer desorption. Emphasis is on the use of rhodamine WT dye as a relatively conservative tracer and propane as the nonconservative gas tracer, on planning field tests, on methods of injection, sampling, and analysis, and on techniques for computing desorption and reaeration coefficients.

  2. Carbon monoxide as a tracer of gas transport in snow and other natural porous media

    NARCIS (Netherlands)

    Huwald, H.; Selker, J.S.; Tyler, S.W.; Calaf, M.; Van de Giesen, N.C.; Parlange, M.B.

    2012-01-01

    The movement of air in natural porous media is complex and challenging to measure. Yet gas transport has important implications, for instance, for the evolution of the seasonal snow cover and for water vapor transport in soil. A novel in situmulti-sensor measurement system providing high-resolution

  3. Natural tracer profiles across argillaceous formations

    Energy Technology Data Exchange (ETDEWEB)

    Mazurek, Martin, E-mail: mazurek@geo.unibe.ch [Rock-Water Interaction, Institute of Geological Sciences, University of Bern (Switzerland); Alt-Epping, Peter [Rock-Water Interaction, Institute of Geological Sciences, University of Bern (Switzerland); Bath, Adrian [Intellisci, Willoughby on the Wolds, Loughborough LE12 6SZ (United Kingdom); Gimmi, Thomas [Rock-Water Interaction, Institute of Geological Sciences, University of Bern (Switzerland)] [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland); Niklaus Waber, H. [Rock-Water Interaction, Institute of Geological Sciences, University of Bern (Switzerland); Buschaert, Stephane [Andra, Parc de la Croix Blanche, 92298 Chatenay-Malabry Cedex (France); Canniere, Pierre De; Craen, Mieke De [SCK-CEN, 2400 Mol (Belgium); Gautschi, Andreas [Nagra, 5430 Wettingen (Switzerland); Savoye, Sebastien [IRSN, 92262 Fontenay-aux-Roses Cedex (France); Vinsot, Agnes [Andra, Parc de la Croix Blanche, 92298 Chatenay-Malabry Cedex (France); Wemaere, Isabelle [SCK-CEN, 2400 Mol (Belgium); Wouters, Laurent [Ondraf/Niras, 1210 Brussels (Belgium)

    2011-07-15

    Highlights: > Solute transport processes in clay and shale formations at nine sites are examined. > Conservative pore-water tracers (e.g. Cl{sup -}, {delta}{sup 18}O, {delta}{sup 2}H, He) show regular profiles. > These indicate the dominance of diffusive transport over times of 10{sup 5}-10{sup 6} years. > The contribution of vertical advection to transport is limited or negligible. > Modelled evolution times are in line with independent palaeo-hydrogeological data. - Abstract: Argillaceous formations generally act as aquitards because of their low hydraulic conductivities. This property, together with the large retention capacity of clays for cationic contaminants, has brought argillaceous formations into focus as potential host rocks for the geological disposal of radioactive and other waste. In several countries, programmes are under way to characterise the detailed transport properties of such formations at depth. In this context, the interpretation of profiles of natural tracers in pore waters across the formations can give valuable information about the large-scale and long-term transport behaviour of these formations. Here, tracer-profile data, obtained by various methods of pore-water extraction for nine sites in central Europe, are compiled. Data at each site comprise some or all of the conservative tracers: anions (Cl{sup -}, Br{sup -}), water isotopes ({delta}{sup 18}O, {delta}{sup 2}H) and noble gases (mainly He). Based on a careful evaluation of the palaeo-hydrogeological evolution at each site, model scenarios are derived for initial and boundary pore-water compositions and an attempt is made to numerically reproduce the observed tracer distributions in a consistent way for all tracers and sites, using transport parameters derived from laboratory or in situ tests. The comprehensive results from this project have been reported in . Here the results for three sites are presented in detail, but the conclusions are based on model interpretations of the

  4. Tracer Diffusion in a Soft Glassy Material

    Science.gov (United States)

    Petit, Laure; Barentin, Catherine; Colombani, Jean; Ybert, Christophe; Barrat, Jean-Louis; Bocquet, Lydéric

    2008-07-01

    We have carried out Fluorescence Recovery After Photobleaching measurements of the diffusion of tracers of various sizes in a colloidal glass (a Laponite suspension). We have shown that the diffusion is only dependent on the ratio of the tracer size and the distance between Laponite disks. This suggests that the tracer diffusion hindrance in the glass stems from the hydrodynamical interactions between the tracer and the Laponite network, the physico-chemical Laponite-tracer interaction playing a negligible role.

  5. Elucidation of hydrogen mobility in tetralin under coal liquefaction conditions using a tritium tracer method. Effects of the addition of H2S and H2O; Tritium tracer ho wo mochiita sekitan ekika hanno jokenka deno tetralin no suiso idosei hyoka. Ryuka suiso oyobi mizu no tenka koka

    Energy Technology Data Exchange (ETDEWEB)

    Kanbe, M.; Saito, M.; Ishihara, A.; Kabe, T. [Tokyo University of Agriculture and Technology, Tokyo (Japan)

    1996-10-28

    It was previously reported that the tritium tracer method is useful for the quantitative consideration of hydrogen behavior in coal during coal liquefaction reaction. Tetralin is excellent hydrogen donating solvent, and is considered as one of the model compounds of coal. In this study, effects of H2S and H2O on the hydrogen exchange reaction between tetralin and gaseous hydrogen labeled by tritium were investigated. It was suggested that the conversion of tetralin and the hydrogen exchange reaction between gaseous hydrogen and tetralin proceed through the radical reaction mechanism with a tetralyl radical as an intermediate product. When H2S existed in this reaction, the hydrogen exchange yield increased drastically without changing the conversion yield. This suggested that the hydrogen exchange reaction proceeds even in the reaction where radical does not give any effect. In the case of H2O addition, the conversion yield and hydrogen exchange rate decreased into a half or one-third. It was suggested that H2O inhibited the formation process of tetralyl radical. 6 refs., 4 figs.

  6. Pulmonary edema in acute carbon monoxide poisoning

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kun Sang; Chang, Kee Hyun; Lee, Myung Uk [Seoul National University College of Medicine, Seoul (Korea, Republic of)

    1974-10-15

    Acute carbon monoxide poisoning has frequently occurred in Korean, because of the coal briquette being widely used as fuel in Korean residences. Carbon monoxide poisoning has been extensively studied, but it has been sparsely reported that pulmonary edema may develop in acute CO poisoning. We have noticed nine cases of pulmonary edema in acute CO poisoning last year. Other possible causes of pulmonary edema could be exclude in all cases but one. The purpose of this paper is to describe nine cases of pulmonary edema complicated in acute CO poisoning and discuss the pathogenesis and the prognosis.

  7. 40 CFR 60.103 - Standard for carbon monoxide.

    Science.gov (United States)

    2010-07-01

    ... Refineries § 60.103 Standard for carbon monoxide. Each owner or operator of any fluid catalytic cracking unit... regenerator any gases that contain carbon monoxide (CO) in excess of 500 ppm by volume (dry basis)....

  8. [Carbon monoxide metabolism by photosynthetic bacteria]. Progress report

    Energy Technology Data Exchange (ETDEWEB)

    1989-12-31

    Research continued on the metabolism of carbon monoxide by Rhodospirillum rubrum. This report discusses progress on the activity, induction, inhibition, and spectroscopic analysis of the enzyme Carbon Monoxide Dehydrogenase. (CBS)

  9. Carbon Monoxide Hazards from Small Gasoline Powered Engines

    Science.gov (United States)

    ... Topics Publications and Products Programs Contact NIOSH NIOSH CARBON MONOXIDE Recommend on Facebook Tweet Share Compartir On this Page Recommendations NIOSH Publications Worker Notification Program Carbon Monoxide Hazards from Small Gasoline Powered Engines Many ...

  10. Scanning imaging absorption spectrometer for atmospheric chartography carbon monoxide total columns: statistical evaluation and comparison with chemistry transport model results

    NARCIS (Netherlands)

    de Laat, A.T.J.; Gloudemans, A.M.S.; Aben, I.; Krol, M.C.; Meirink, J.F.; van der Werf, G.R.; Schrijver, H.

    2007-01-01

    This paper presents a detailed statistical analysis of one year (September 2003 to August 2004) of global Scanning Imaging Absorption Spectrometer for Atmospheric Chartography (SCIAMACHY) carbon monoxide (CO) total column retrievals from the Iterative Maximum Likelihood Method (IMLM) algorithm, vers

  11. Scanning Imaging Absorption Spectrometer for Atmospheric Chartography carbon monoxide total columns: Statistical evaluation and comparison with chemistry transport model results

    NARCIS (Netherlands)

    Laat, de A.T.J.; Gloudemans, A.M.S.; Aben, I.; Krol, M.C.; Meirink, J.F.; Werf, van der G.R.; Schrijver, H.

    2007-01-01

    This paper presents a detailed statistical analysis of one year (September 2003 to August 2004) of global Scanning Imaging Absorption Spectrometer for Atmospheric Chartography (SCIAMACHY) carbon monoxide (CO) total column retrievals from the Iterative Maximum Likelihood Method (IMLM) algorithm, vers

  12. In-Situ Characterization of Dense Non-Aqueous Phase Liquids Using Partitioning Tracers

    Energy Technology Data Exchange (ETDEWEB)

    Gary A. Pope; Daene C. McKinney; Akhil Datta Gupta; Richard E. Jackson; Minquan Jin

    2000-03-20

    Majors advances have been made during the past three years in our research on interwell partitioning tracers tests (PITTs). These advances include (1) progress on the inverse problem of how to estimate the three-dimensional distribution of NAPL in aquifers from the tracer data, (2) the first ever partitioning tracer experiments in dual porosity media, (3) the first modeling of partitioning tracers in dual porosity media (4) experiments with complex NAPLs such as coal tar, (5) the development of an accurate and simple method to predict partition coefficients using the equivalent alkane carbon number approach, (6) partitioning tracer experiments in large model aquifers with permeability layers, (7) the first ever analysis of partitioning tracer data to estimate the change in composition of a NAPL before and after remediation (8) the first ever analysis of partitioning tracer data after a field demonstration of surfactant foam to remediate NAPL and (9) experiments at elevated temperatures .

  13. Assessment of carbon monoxide values in smokers: a comparison of carbon monoxide in expired air and carboxyhaemoglobin in arterial blood

    DEFF Research Database (Denmark)

    Andersson, Mette F; Møller, Ann M

    2010-01-01

    Smoking increases perioperative complications. Carbon monoxide concentrations can estimate patients' smoking status and might be relevant in preoperative risk assessment. In smokers, we compared measurements of carbon monoxide in expired air (COexp) with measurements of carboxyhaemoglobin (COHb...

  14. Hearing Loss due to Carbon Monoxide Poisoning

    DEFF Research Database (Denmark)

    Mehrparvar, Amir Houshang; Davari, Mohammad Hossein; Mollasadeghi, Abolfazl

    2013-01-01

    Carbon monoxide poisoning is one of the rare causes of hearing loss which may cause reversible or irreversible, unilateral or bilateral hearing loss after acute or chronic exposure. In this report, we present a case of bilateral sensorineural hearing loss in a secondary smelting workshop worker...

  15. Compilation and analyses of results from cross-hole tracer tests with conservative tracers

    Energy Technology Data Exchange (ETDEWEB)

    Hjerne, Calle; Nordqvist, Rune; Harrstroem, Johan (Geosigma AB (Sweden))

    2010-09-15

    Radionuclide transport in hydrogeological formations is one of the key factors for the safety analysis of a future repository of nuclear waste. Tracer tests have therefore been an important field method within the SKB investigation programmes at several sites since the late 1970's. This report presents a compilation and analyses of results from cross-hole tracer tests with conservative tracers performed within various SKB investigations. The objectives of the study are to facilitate, improve and reduce uncertainties in predictive tracer modelling and to provide supporting information for SKB's safety assessment of a final repository of nuclear waste. More specifically, the focus of the report is the relationship between the tracer mean residence time and fracture hydraulic parameters, i.e. the relationship between mass balance aperture and fracture transmissivity, hydraulic diffusivity and apparent storativity. For 74 different combinations of pumping and injection section at six different test sites (Studsvik, Stripa, Finnsjoen, Aespoe, Forsmark, Laxemar), estimates of mass balance aperture from cross-hole tracer tests as well as transmissivity were extracted from reports or in the SKB database Sicada. For 28 of these combinations of pumping and injection section, estimates of hydraulic diffusivity and apparent storativity from hydraulic interference tests were also found. An empirical relationship between mass balance aperture and transmissivity was estimated, although some uncertainties for individual data exist. The empirical relationship between mass balance aperture and transmissivity presented in this study deviates considerably from other previously suggested relationships, such as the cubic law and transport aperture as suggested by /Dershowitz and Klise 2002/, /Dershowitz et al. 2002/ and /Dershowitz et al. 2003/, which also is discussed in this report. No clear and direct empirical relationship between mass balance aperture and hydraulic

  16. Quantifying solute transport processes: are chemically "conservative" tracers electrically conservative?

    Science.gov (United States)

    Singha, Kamini; Li, Li; Day-Lewis, Frederick D.; Regberg, Aaron B.

    2012-01-01

    The concept of a nonreactive or conservative tracer, commonly invoked in investigations of solute transport, requires additional study in the context of electrical geophysical monitoring. Tracers that are commonly considered conservative may undergo reactive processes, such as ion exchange, thus changing the aqueous composition of the system. As a result, the measured electrical conductivity may reflect not only solute transport but also reactive processes. We have evaluated the impacts of ion exchange reactions, rate-limited mass transfer, and surface conduction on quantifying tracer mass, mean arrival time, and temporal variance in laboratory-scale column experiments. Numerical examples showed that (1) ion exchange can lead to resistivity-estimated tracer mass, velocity, and dispersivity that may be inaccurate; (2) mass transfer leads to an overestimate in the mobile tracer mass and an underestimate in velocity when using electrical methods; and (3) surface conductance does not notably affect estimated moments when high-concentration tracers are used, although this phenomenon may be important at low concentrations or in sediments with high and/or spatially variable cation-exchange capacity. In all cases, colocated groundwater concentration measurements are of high importance for interpreting geophysical data with respect to the controlling transport processes of interest.

  17. Oxalyl chloride as a practical carbon monoxide source for carbonylation reactions

    DEFF Research Database (Denmark)

    Hansen, Steffen V F; Ulven, Trond

    2015-01-01

    A method for generation of high-quality carbon monoxide by decomposition of oxalyl chloride in an aqueous hydroxide solution is described. The usefulness of the method is demonstrated in the synthesis of heterocycles and for hydroxy-, alkoxy-, amino-, and reductive carbonylation reactions...

  18. The Effect of Carbon Monoxide Poisoning on Platelet Volume in Children

    Directory of Open Access Journals (Sweden)

    Halise Akça

    2017-04-01

    Full Text Available Introduction: Carbon monoxide poisoning is one of the most important causes of morbidity and mortality. There is increasing evidence supporting the important role of mean platelet volume (MPV as a marker of hypoxia and inflammation. In this study, we aimed to determine changes in MPV values in pediatric patients with carbon monoxide poisoning. Methods: We retrospectively evaluated children who were diagnosed with carbon monoxide poisoning in our hospital between January 2005 and 2014. Results: We included 228 children with carbon monoxide poisoning (49% male in this retrospective, controlled study. The mean age of the patients was 88±56 months. Control group consisted of 200 age-matched healthy children. There was no statistically significant difference in MPV levels between the study and control groups (8.43±1.1 fL and 8.26±0.7 fL, respectively. No correlation of MPV and platelet count with carboxyhemoglobin (COHb was found. Conclusion: In our study, it was determined that MPV value was not a helpful parameter for predicting the diagnosis of acute carbon monoxide poisoning in childhood. The difference between the MPV values and the lack of significance and the absence of correlation between MPV value and COHb level led to the fact that MPV was not a guide indicating the clinical severity of the condition.

  19. Identification and characterization of conservative organic tracers for use as hydrologic tracers for the Yucca Mountain Site Characterization Study; Progress report, June 1--December 31, 1990

    Energy Technology Data Exchange (ETDEWEB)

    Stetzenbach, K.J.

    1990-12-31

    Ground water tracers are solutes dissolved in or carried by ground water to delineate flow pathways. Tracers provide information on direction and speed of water movement and that of contaminants that might be conveyed by the water. Tracers can also be used to measure effective porosity, hydraulic conductivity, dispersivity and solute distribution coefficients. For most applications tracers should be conservative, that is, move at the same rate as the water and not sorb to aquifer materials. Tracers must have a number of properties to be functional. Regardless of the desired properties, the chemical and physical behavior of a tracer in ground water and the porous medium under study must be understood. Good estimates of tracer behavior can be obtained from laboratory studies. Studies in this proposal will address tracer properties with analytical method development, static sorption and degradation studies and column transport studies, Mutagenicity tests will be performed on promising candidates. The tracers that will be used for these experiments are fluorinated organic acids and other organic compounds that have the chemical and biological stability necessary to be effective in the Yucca Mountain environment. Special emphasis will be placed on compounds that fluoresce or have very large ultraviolet absorption coefficients for very high analytical sensitivity.

  20. Microfilter paper method for 17. cap alpha. -hydroxyprogesterone radioimmunoassay: its application for rapid screening for congenital adrenal hyperplasia. [Tritium tracer techniques

    Energy Technology Data Exchange (ETDEWEB)

    Pang, S.; Hotchkiss, J.; Drash, A.L.; Levine, L.S.; New, M.I.

    1977-11-01

    A new micromethod for measuring a steroid in blood collected on filter paper has been developed. The method is easy and rapid and has the specificity, accuracy and precision of RIA in whole plasma. Less than 20 ..mu..l of blood is required, and, therefore, samples may be obtained with heel prick. This method has been applied to the determination of 17..cap alpha..-hydroxyprogesterone (17..cap alpha..-OH-P) for screening patients with congenital adrenal hyperplasia (CAH) due to 21-hydroxylase deficiency. There was excellent correlation (r = .94) between the values of 17..cap alpha..-OH-P obtained by microfilter paper method and those from plasma samples of cord (40 +- 13 ng/ml) and neonatal blood (<3.6 ng/ml) in normal infants. In six neonates at risk for CAH the diagnosis was made utilizing the microfilter paper method. 17..cap alpha..-OH-P concentrations were highly elevated in both filter paper eluates of whole blood (67 to 360 ng/ml of plasma) and simultaneously obtained plasma concentration (74 to 395 ng/ml) in affected infants. The concentrations of 17..cap alpha..-OH-P remained unchanged in dried filter paper blood when stored at room temperature for up to 21 days. Thus, filter paper with dried blood may be sent for steroid assay by mail. The ease with which samples may be transported and the minute amount of sample necessary make this method a promising screening test for CAH.

  1. Polyethyleneimine as tracer for electron microscopy

    NARCIS (Netherlands)

    Schurer, Jacob Willem

    1980-01-01

    In this thesis the development of a tracer particle for use in electron microscopy is described. Attempts were made to use this tracer particle in immuno-electron microscopy and to trace negatively charged tissue components. ... Zie: Summary

  2. Multimodality evoked potentials in patients with delayed encephalopathy after acute carbon monoxide poisoning

    Institute of Scientific and Technical Information of China (English)

    Xiahong Wang; Bo Xiao; Renjun Gu; Lan Xiao; Yi Yang; Yinhui Hao; Nini Wang; Junlin Mu; Jinggang Yin

    2006-01-01

    Objective: To evaluate the diagnostic and prognostic values in patients with delayed encephalopathy after acute carbon monoxide poisoning. Methods: The tibial nerve somatosensory evoked potentials (SEPs), vision evoked potentials (VEPs), and brain stem audition evoked potentials(BAEPs) were performed in 32 healthy adults and 43 patients with delayed encephalopathy after acute carbon monoxide poisoning. Results: This paper indicated abnormalities of tibial nerve SEPs in 31 patients (31/43, 72.1%), VEPs in 17 patients (17/28, 60.7%), and BAEPs in 14 patients (14/43, 32.6%). These results showed that the greatest diagnostic value was SEPs, followed by VEPs and, BAEPs with the lowest sensitivity. Conclusion: Multimodality evoked potentials (EPs) can be used for evaluating the diagnostic and prognostic values in cases of delayed encephalopathy after acute carbon monoxide poisoning.

  3. Range Measurements of keV Hydrogen Ions in Solid Oxygen and Carbon Monoxide

    DEFF Research Database (Denmark)

    Schou, Jørgen; Sørensen, H.; Andersen, H.H.

    1984-01-01

    Ranges of 1.3–3.5 keV/atom hydrogen and deuterium molecular ions have been measured by a thin-film reflection method. The technique, used here for range measurements in solid oxygen and carbon monoxide targets, is identical to the one used previously for range measurements in hydrogen and nitrogen....... The main aim was to look for phase-effects, i.e. gas-solid differences in the stopping processes. While measured ranges in solid oxygen were in agreement with known gas data, the ranges in solid carbon monoxide were up to 50% larger than those calculated from gas-stopping data. The latter result agrees...

  4. Assessing preferential flow by simultaneously injecting nanoparticle and chemical tracers

    KAUST Repository

    Subramanian, S. K.

    2013-01-01

    The exact manner in which preferential (e.g., much faster than average) flow occurs in the subsurface through small fractures or permeable connected pathways of other kinds is important to many processes but is difficult to determine, because most chemical tracers diffuse quickly enough from small flow channels that they appear to move more uniformly through the rock than they actually do. We show how preferential flow can be assessed by injecting 2 to 5 nm carbon particles (C-Dots) and an inert KBr chemical tracer at different flow rates into a permeable core channel that is surrounded by a less permeable matrix in laboratory apparatus of three different designs. When the KBr tracer has a long enough transit through the system to diffuse into the matrix, but the C-Dot tracer does not, the C-Dot tracer arrives first and the KBr tracer later, and the separation measures the degree of preferential flow. Tracer sequestration in the matrix can be estimated with a Peclet number, and this is useful for experiment design. A model is used to determine the best fitting core and matrix dispersion parameters and refine estimates of the core and matrix porosities. Almost the same parameter values explain all experiments. The methods demonstrated in the laboratory can be applied to field tests. If nanoparticles can be designed that do not stick while flowing through the subsurface, the methods presented here could be used to determine the degree of fracture control in natural environments, and this capability would have very wide ranging value and applicability.

  5. Rapid and simple determination of delivery after iontophoretic and pressure injections of radiolabeled tracer substances

    Energy Technology Data Exchange (ETDEWEB)

    Imai, H.; Steindler, D.A.; Kitai, S.T. (Michigan State Univ., East Lansing (USA))

    1983-04-01

    A fluorographic method is described using X-ray film analysis for the determination of delivery of radiolabeled tracer substances both in Agar plates and in tissue sections. This method is most useful in neuroanatomical autoradiographic studies for providing rapid identification of delivery, placement and extent of an injection site after iontophoresis or pressure injections of radiolabeled axonal tracer substances.

  6. Photosynthetic carbon monoxide metabolism by sugarcane leaves

    Energy Technology Data Exchange (ETDEWEB)

    Kortschak, H.P.; Nickell, L.G.

    1973-01-01

    The photosynthetic carbon monoxide metabolism by sugarcane was studied to determine whether substantial quantities of CO are removed from the air by fields in Hawaii. Leaves metabolized low CO concentrations photosynthetically, with sucrose as an end product. Rates of uptake were of the order of 10/sup -4/ power mg/d sq m/hr. This was to low to be significant in removing CO from the atmosphere.

  7. Sensorineural Hearing Loss following Carbon Monoxide Poisoning

    Directory of Open Access Journals (Sweden)

    Joseph P. Pillion

    2012-01-01

    Full Text Available A case study is presented of a 17-year-old male who sustained an anoxic brain injury and sensorineural hearing loss secondary to carbon monoxide poisoning. Audiological data is presented showing a slightly asymmetrical hearing loss of sensorineural origin and mild-to-severe degree for both ears. Word recognition performance was fair to poor bilaterally for speech presented at normal conversational levels in quiet. Management considerations of the hearing loss are discussed.

  8. Tracer-tracer relations as a tool for research on polar ozone loss

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, Rolf

    2010-07-01

    The report includes the following chapters: (1) Introduction: ozone in the atmosphere, anthropogenic influence on the ozone layer, polar stratospheric ozone loss; (2) Tracer-tracer relations in the stratosphere: tracer-tracer relations as a tool in atmospheric research; impact of cosmic-ray-induced heterogeneous chemistry on polar ozone; (3) quantifying polar ozone loss from ozone-tracer relations: principles of tracer-tracer correlation techniques; reference ozone-tracer relations in the early polar vortex; impact of mixing on ozone-tracer relations in the polar vortex; impact of mesospheric intrusions on ozone-tracer relations in the stratospheric polar vortex calculation of chemical ozone loss in the arctic in March 2003 based on ILAS-II measurements; (4) epilogue.

  9. Determination of the separation efficiencies of a single-stage cryogenic distillation setup to remove krypton out of xenon by using a {sup 83m}Kr tracer method

    Energy Technology Data Exchange (ETDEWEB)

    Rosendahl, S., E-mail: rosendahl@wwu.de; Brown, E.; Fieguth, A.; Huhmann, C.; Murra, M.; Weinheimer, C. [Institut für Kernphysik, Wilhelm-Klemm Straße 09, 48149 Münster (Germany); Cristescu, I. [Karlsruher Institut für Technologie, Hermann Von Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Lebeda, O. [Nuclear Physics Institute, Czech Academy of Sciences, CZ 250 68 Řež (Czech Republic)

    2015-11-15

    The separation of krypton and xenon is of particular importance for the field of direct dark matter search with liquid xenon detectors. The intrinsic contamination of the xenon with radioactive {sup 85}Kr makes a significant background for these kinds of low count-rate experiments and has to be removed beforehand. This can be achieved by cryogenic distillation, a technique widely used in industry, using the different vapor pressures of krypton and xenon. In this paper, we present an investigation on the separation performance of a single stage distillation system using a radioactive {sup 83m}Kr-tracer method. The separation characteristics under different operation conditions are determined for very low concentrations of krypton in xenon at the level of {sup 83m}Kr/Xe = 1.9 ⋅ 10{sup −15}, demonstrating, that cryogenic distillation in this regime is working. The observed separation is in agreement with the expectation from the different volatilities of krypton and xenon. This cryogenic distillation station is the first step on the way to a multi-stage cryogenic distillation column for the next generation of direct dark matter experiment XENON1T.

  10. A Tracer Method for Computing Type Ia Supernova Yields: Burning Model Calibration, Reconstruction of Thickened Flames, and Verification for Planar Detonations

    CERN Document Server

    Townsley, Dean M; Timmes, F X; Calder, Alan C; Brown, Edward F

    2016-01-01

    We refine our previously introduced parameterized model for explosive carbon-oxygen fusion during thermonuclear supernovae (SN Ia) by adding corrections to post-processing of recorded Lagrangian fluid element histories to obtain more accurate isotopic yields. Deflagration and detonation products are verified for propagation in a uniform density medium. A new method is introduced for reconstructing the temperature-density history within the artificially thick model deflagration front. We obtain better than 5\\% consistency between the electron capture computed by the burning model and yields from post-processing. For detonations, we compare to a benchmark calculation of the structure of driven steady-state planar detonations performed with a large nuclear reaction network and error-controlled integration. We verify that, for steady-state planar detonations down to a density of 5x10^6 g/cc, our post processing matches the major abundances in the benchmark solution typically to better than 10% for times greater t...

  11. Palladium-catalyzed carbonylative sonogashira coupling of aryl bromides using near stoichiometric carbon monoxide

    DEFF Research Database (Denmark)

    Neumann, Karoline T.; Laursen, Simon R.; Lindhardt, Anders T.

    2014-01-01

    A general procedure for the palladium-catalyzed carbonylative Sonogashira coupling of aryl bromides is reported, using near stoichiometric amounts of carbon monoxide. The method allows a broad substrate scope in moderate to excellent yields. The formed alkynone motive serves as a platform...

  12. Short-term effects of carbon monoxide on mortality : An analysis within the APHEA project

    NARCIS (Netherlands)

    Samoli, Evangelia; Touloumi, Giota; Schwartz, Joel; Anderson, Hugh Ross; Schindler, Christian; Forsberg, Bertil; Vigotti, Maria Angela; Vonk, Judith; Kosnik, Mitja; Skorkovsky, Jiri; Katsouyanni, Klea

    2007-01-01

    OBJECTIVES: We investigated the short-term effects of carbon monoxide on total and cardiovascular mortality in 19 European cities participating in the APHEA-2 (Air Pollution and Health: A European Approach) project. METHODS: We examined the association using hierarchical models implemented in two st

  13. Characteristics of Photoacoustic Spectroscopy Detection for Carbon Monoxide Gas Based on DFB Diode Laser

    Institute of Scientific and Technical Information of China (English)

    CHEN Weigen; PENG Xiaojuan; LIU Bingjie; SUN Caixin

    2012-01-01

    The dissolved gas analysis is one of the most effective and convenient methods to diagnose the early discharge faults of transformers. When the fault involves the solid insulation, oil-paper insulation cracks and releases carbon monoxide (CO) gas. Therefore, the detection of CO can forecast the potential inner faults of oil-filled transformers.

  14. Gaseous persufflation with carbon monoxide during ischemia protects the isolated liver and enhances energetic recovery

    NARCIS (Netherlands)

    Koetting, Martina; Leuvenink, Henri; Dombrowski, Frank; Minor, Thomas

    2010-01-01

    Background: The benefit of carbon monoxide as applied by controlled, continuous gaseous persufflation during liver preservation on postischemic graft recovery was investigated in an isolated rat liver model. Methods: Livers from male Wistar rats were retrieved 30 min after cardiac arrest of the dono

  15. Short-term effects of carbon monoxide on mortality : An analysis within the APHEA project

    NARCIS (Netherlands)

    Samoli, Evangelia; Touloumi, Giota; Schwartz, Joel; Anderson, Hugh Ross; Schindler, Christian; Forsberg, Bertil; Vigotti, Maria Angela; Vonk, Judith; Kosnik, Mitja; Skorkovsky, Jiri; Katsouyanni, Klea

    2007-01-01

    OBJECTIVES: We investigated the short-term effects of carbon monoxide on total and cardiovascular mortality in 19 European cities participating in the APHEA-2 (Air Pollution and Health: A European Approach) project. METHODS: We examined the association using hierarchical models implemented in two

  16. Tracer diffusion inside fibrinogen layers

    Science.gov (United States)

    Cieśla, Michał; Gudowska-Nowak, Ewa; Sagués, Francesc; Sokolov, Igor M.

    2014-01-01

    We investigate the obstructed motion of tracer (test) particles in crowded environments by carrying simulations of two-dimensional Gaussian random walk in model fibrinogen monolayers of different orientational ordering. The fibrinogen molecules are significantly anisotropic and therefore they can form structures where orientational ordering, similar to the one observed in nematic liquid crystals, appears. The work focuses on the dependence between level of the orientational order (degree of environmental crowding) of fibrinogen molecules inside a layer and non-Fickian character of the diffusion process of spherical tracer particles moving within the domain. It is shown that in general particles motion is subdiffusive and strongly anisotropic, and its characteristic features significantly change with the orientational order parameter, concentration of fibrinogens, and radius of a diffusing probe.

  17. Tracer diffusion inside fibrinogen layers

    CERN Document Server

    Cieśla, Michał; Sagués, Francesc; Sokolov, Igor M

    2013-01-01

    We investigate the motion of tracer (test) particles in crowded environments by carrying simulations of two-dimensional Gaussian random walk in model fibrinogen monolayers of different orientational ordering. The fibrinogen molecules are significantly anisotropic and therefore they can form structures where orientational ordering, similar to the one observed in nematic liquid crystals, appears. The work focuses on the dependence between level of the orientational order (degree of environmental crowding) of fibrinogen molecules inside a layer and non-Fickian character of the diffusion process of spherical tracer particles moving within the domain. It is shown that in general particles motion is subdiffusive and strongly anisotropic, and its characteristic features significantly change with the orientational order parameter, concentration of fibrinogens and radius of a diffusing probe.

  18. Effect of room air recirculation delay on the decay rate of tracer gas concentration

    Energy Technology Data Exchange (ETDEWEB)

    Kristoffersen, A.R.; Gadgil, A.J.; Lorenzetti, D.M.

    2004-05-01

    Tracer gas measurements are commonly used to estimate the fresh air exchange rate in a room or building. Published tracer decay methods account for fresh air supply, infiltration, and leaks in ductwork. However, the time delay associated with a ventilation system recirculating tracer back to the room also affects the decay rate. We present an analytical study of tracer gas decay in a well-mixed, mechanically-ventilated room with recirculation. The analysis shows that failing to account for delays can lead to under- or over-estimates of the fresh air supply, depending on whether the decay rate calculation includes the duct volume.

  19. Formation of orthorhombic tin dioxide from mechanically milled monoxide powders

    Science.gov (United States)

    Lamelas, F. J.

    2004-12-01

    X-ray scattering measurements are used to show that the metastable orthorhombic phase of tin dioxide is produced by the oxidation of mechanically milled litharge-phase tin monoxide. After milling to a grain size of approximately 20nm, followed by heating to 575°C, the fraction of the orthorhombic phase is approximately 80%. The orthorhombic phase was originally observed in high-pressure experiments, but more recently, it has been produced in a wide variety of thin-film and nanoparticle samples. The data presented here demonstrate the importance of small-grain-size tin monoxide as a precursor in the ambient-pressure synthesis of the orthorhombic phase. This result has practical importance in the production of tin dioxide gas sensors. A more fundamental observation is that the particle size of a precursor phase can have a marked effect on subsequent phases produced during oxidation. Lastly, a formula for determining the orthorhombic fraction in two-phase tin dioxide samples is developed using the method of standard additions.

  20. A carbon monoxide passive sampler: Research and development needs

    Energy Technology Data Exchange (ETDEWEB)

    Traynor, G.W.; Apte, M.G.; Diamond, R.C.; Woods, A.L.

    1991-11-01

    In rare instances, carbon monoxide (CO) levels in houses can reach dangerously high concentrations, causing adverse health effects ranging from mild headaches to, under extreme conditions, death. Hundreds of fatal accidental carbon monoxide poisonings occur each year primarily due to the indoor operation of motor vehicles, the indoor use of charcoal for cooking, the operation of malfunctioning vented and unvented combustion appliances, and the misuse combustion appliances. Because there is a lack of simple, inexpensive, and accurate field sampling instrumentation, it is difficult for gas utilities and researchers to conduct field research studies designed to quantify the concentrations of CO in residences. Determining the concentration of CO in residences is the first step towards identifying the high risk appliances and high-CO environments which pose health risks. Thus, there exists an urgent need to develop and field-validate a CO-quantifying technique suitable for affordable field research. A CO passive sampler, if developed, could fulfill these requirements. Existing CO monitoring techniques are discussed as well as three potential CO-detection methods for use in a CO passive sampler. Laboratory and field research needed for the development and validation of an effective and cost-efficient CO passive sampler are also discussed.

  1. Assessment of Average Tracer Concentration Approach for Flow Rate Measurement and Field Calibration

    Directory of Open Access Journals (Sweden)

    P. Sidauruk

    2015-12-01

    Full Text Available Tracer method is one of the methods available for open channel flow rate measurements such as in irrigation canals. Average tracer concentration approach is an instantaneous injection method that based on the average tracer concentrations value at the sampling point. If the procedures are correct and scientific considerations are justified, tracer method will give relatively high accuracy of measurements. The accuracy of the average tracer concentration approach has been assessed both in laboratory and field. The results of accuracy tests of open channel flow that has been conducted at the Center for Application Isotopes and Radiation Laboratory-BATAN showed that the accuracy level of average concentrations approach method was higher than 90% compared to the true value (volumetric flow rate. The accuracy of average tracer concentration approach was also assessed during the application of the method to measure flow rate of Mrican irrigation canals as an effort to perform field calibration of existing weirs. Both average tracer concentration approach and weirs can predict the trend of the flow correctly. However, it was observed that flow discrepancies between weirs measurement and average tracer concentration approach predictions were as high as 27%. The discrepancies might be due to the downgrading performances of the weirs because of previous floods and high sediment contents of the flow

  2. Groundwater prospecting for sandstone-type uranium deposits: the merits of mineral-solution equilibria versus single element tracer methods. Volume II

    Energy Technology Data Exchange (ETDEWEB)

    Wanty, R.B.; Langmuir, D.; Chatham, J.R.

    1981-08-01

    This report presents the results of further research on the groundwater geochemistry of 96 well waters in two uraniferous aquifers in Texas and Wyoming, and is a continuation of the work presented by Chatham et al. (1981). In this study variations in concentrations of U, As, Mo, Se and V were compared with the saturation state of the groundwater with respect to mineral phases of these elements known or expected to occur in each area. The non-radiogenic trace elements exhibited strong redox dependence consistent with thermodynamic predictions, but their variations did not pinpoint existing uranium ore bodies, because of a shift in groundwater flow patterns since the time of ore emplacement. Saturation levels of trace element minerals such as realgar, native Se, and molybdenite showed broad anomalies around the ore-bearing areas, similar to patterns found for U minerals by Langmuir and Chatham (1980), and Chatham et al. (1981). The radiogenic elements Ra and Rn showed significant anomalies directly within the ore zones. Helium anomalies were displaced in the direction of groundwater flow, but by their magnitude and areal extent provided strong evidence for the existence of nearby uranium accumulations. Uranium isotope ratios showed no systematic variations within the two aquifers studied. Saturation maps for kaolinite, illite, montmorillonite and the zeolites analcime and clinoptilolite provided 1 to 2 km anomalies around the ore at the Texas site. Saturation values for the gangue minerals pyrite and calcite defined the redox interface and often suggested the position of probable uranium mineralization. When properly used, the groundwater geochemical concepts for exploration can accurately pinpoint uranium mineralization at a fraction of the cost of conventional methods that involve test drilling and geophysical and core logging.

  3. Technique for measuring carbon monoxide uptake in mice

    Energy Technology Data Exchange (ETDEWEB)

    Depledge, M.H.; Collis, C.H.; Chir, B.; Barrett, A.

    1981-04-01

    A new method has been developed for measuring carbon monoxide (CO) uptake in mice. Each animal was placed in a syringe and allowed to rebreathe a mixture of CO and helium (He) for 60 s. CO uptake was detemined from a comparison of CO and He concentrations before and after rebreathing. Weight specific CO uptake increased with body weight in CBA mice weighing between 20 to 35 gr. In larger mice, size dependence was less marked, although a slight fall in CO uptake was observed in older animals. Anaesthesia reduced ventilatory rate and CO uptake to a variable extent. The method is reproducible, non-invasive and does not require anaesthesia; consequently, it can be used to study serial changes in lung function. It is sensitive enough to detect lung damage in CBA mice following 16 Gy total body irradiation. Values of diffusing capacity obtained for mice using this method are consistent with published values.

  4. Simultaneous Analyses and Applications of Multiple Fluorobenzoate and Halide Tracers in Hydrologic Studies

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Q; Moran, J E

    2004-01-22

    An analytical method that employs ion chromatography has been developed to more fully exploit the use of fluorobenzoic acids (FBAs) and halides as hydrologic tracers. In a single run, this reliable, sensitive, and robust method can simultaneously separate and quantify halides (fluoride, chloride, bromide, and iodide) and up to seven FBAs from other common groundwater constituents (e.g., nitrate and sulfate). The usefulness of this ion chromatographic (IC) analytical method is demonstrated in both field and laboratory tracer experiments. Field experiments in unsaturated tuff featuring fractures or a fault show that this efficient and cost-effective method helps achieve the objectives of tracer studies that use multiple FBAs and/or diffusivity tracers (simultaneous use of one or more FBA and halide). The field study examines the hydrologic response of fractures and the matrix to different flow rates and the contribution of matrix diffusion in chemical transport. Laboratory tracer experiments with eight geologic media from across the United States--mostly from Department of Energy facilities where groundwater contamination is prevalent and where subsurface characterization employing tracers has been ongoing or is in need--reveal several insights about tracer transport behavior: (1) Bromide and FBAs are not always transported conservatively. (2) The delayed transport of these anionic tracers is likely related to geologic media characteristics, such as organic matter, pH, iron oxide content, and clay mineralogy. (3) Any use of iodine as a hydrologic tracer should take into account the different sorption behaviors of iodide and iodate and the possible conversion of iodine's initial chemical form. (4) The transport behavior of potential FBA and halide tracers under relevant geochemical conditions should be evaluated before beginning ambitious, large-scale field tracer experiments.

  5. Simultaneous Analyses and Applications of Multiple Fluorobenzoate and Halide Tracers in Hydrologic Studies

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Q; Moran, J E

    2004-01-22

    An analytical method that employs ion chromatography has been developed to more fully exploit the use of fluorobenzoic acids (FBAs) and halides as hydrologic tracers. In a single run, this reliable, sensitive, and robust method can simultaneously separate and quantify halides (fluoride, chloride, bromide, and iodide) and up to seven FBAs from other common groundwater constituents (e.g., nitrate and sulfate). The usefulness of this ion chromatographic (IC) analytical method is demonstrated in both field and laboratory tracer experiments. Field experiments in unsaturated tuff featuring fractures or a fault show that this efficient and cost-effective method helps achieve the objectives of tracer studies that use multiple FBAs and/or diffusivity tracers (simultaneous use of one or more FBA and halide). The field study examines the hydrologic response of fractures and the matrix to different flow rates and the contribution of matrix diffusion in chemical transport. Laboratory tracer experiments with eight geologic media from across the United States--mostly from Department of Energy facilities where groundwater contamination is prevalent and where subsurface characterization employing tracers has been ongoing or is in need--reveal several insights about tracer transport behavior: (1) Bromide and FBAs are not always transported conservatively. (2) The delayed transport of these anionic tracers is likely related to geologic media characteristics, such as organic matter, pH, iron oxide content, and clay mineralogy. (3) Any use of iodine as a hydrologic tracer should take into account the different sorption behaviors of iodide and iodate and the possible conversion of iodine's initial chemical form. (4) The transport behavior of potential FBA and halide tracers under relevant geochemical conditions should be evaluated before beginning ambitious, large-scale field tracer experiments.

  6. TracerLPM (Version 1): An Excel® workbook for interpreting groundwater age distributions from environmental tracer data

    Science.gov (United States)

    Jurgens, Bryant C.; Böhlke, J.K.; Eberts, Sandra M.

    2012-01-01

    TracerLPM is an interactive Excel® (2007 or later) workbook program for evaluating groundwater age distributions from environmental tracer data by using lumped parameter models (LPMs). Lumped parameter models are mathematical models of transport based on simplified aquifer geometry and flow configurations that account for effects of hydrodynamic dispersion or mixing within the aquifer, well bore, or discharge area. Five primary LPMs are included in the workbook: piston-flow model (PFM), exponential mixing model (EMM), exponential piston-flow model (EPM), partial exponential model (PEM), and dispersion model (DM). Binary mixing models (BMM) can be created by combining primary LPMs in various combinations. Travel time through the unsaturated zone can be included as an additional parameter. TracerLPM also allows users to enter age distributions determined from other methods, such as particle tracking results from numerical groundwater-flow models or from other LPMs not included in this program. Tracers of both young groundwater (anthropogenic atmospheric gases and isotopic substances indicating post-1940s recharge) and much older groundwater (carbon-14 and helium-4) can be interpreted simultaneously so that estimates of the groundwater age distribution for samples with a wide range of ages can be constrained. TracerLPM is organized to permit a comprehensive interpretive approach consisting of hydrogeologic conceptualization, visual examination of data and models, and best-fit parameter estimation. Groundwater age distributions can be evaluated by comparing measured and modeled tracer concentrations in two ways: (1) multiple tracers analyzed simultaneously can be evaluated against each other for concordance with modeled concentrations (tracer-tracer application) or (2) tracer time-series data can be evaluated for concordance with modeled trends (tracer-time application). Groundwater-age estimates can also be obtained for samples with a single tracer measurement at one

  7. Development of radioisotope tracer technology and nucleonic control system

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Joon Ha; Lee, Myun Joo; Jung, Sung Hee and others

    1999-04-01

    The purpose of this study is to develop the radioisotope tracer technology, which can be used in solving industrial and environmental problems and basic technology of nuclear control systems that are widely used for automation of industrial plants, and to build a strong tracer group to support the local industries. In relation to the tracer technology, the data acquisition system, the column scanning equipment and the detection pig for a leakage test have been developed. In order to use in analyzing data of tracer experiments, a computer program for the analysis of residence time distribution has been created as well. These results were utilized in developing the tracer technologies, such as the column scanning, the flow measurement using the dilution method, the simultaneous monitoring rotational movement of piston rings and the optimization of a waste water treatment facility, and the technologies were successfully demonstrated in the local industrial. The stripper of RFCC reactor has been examined to find an unwanted structure in it by imminent request from the industry. Related to the development of nucleonic control system, the state of art report on the technology has been written and an equipment for the analysis of asphalt content has been developed. (author)

  8. Compact Instrument for Measurement of Atmospheric Carbon Monoxide Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Southwest Sciences proposed the development of a rugged, compact, and automated instrument for the high sensitivity measurement of tropospheric carbon monoxide...

  9. Preparation of intravenous cholesterol tracer using current good manufacturing practices.

    Science.gov (United States)

    Lin, Xiaobo; Ma, Lina; Racette, Susan B; Swaney, William P; Ostlund, Richard E

    2015-12-01

    Studies of human reverse cholesterol transport require intravenous infusion of cholesterol tracers. Because insoluble lipids may pose risk and because it is desirable to have consistent doses of defined composition available over many months, we investigated the manufacture of cholesterol tracer under current good manufacturing practice (CGMP) conditions appropriate for phase 1 investigation. Cholesterol tracer was prepared by sterile admixture of unlabeled cholesterol or cholesterol-d7 in ethanol with 20% Intralipid(®). The resulting material was filtered through a 1.2 micron particulate filter, stored at 4°C, and tested at time 0, 1.5, 3, 6, and 9 months for sterility, pyrogenicity, autoxidation, and particle size and aggregation. The limiting factor for stability was a rise in thiobarbituric acid-reacting substances of 9.6-fold over 9 months (P postproduction. CGMP manufacturing methods can be achieved in the academic setting and need to be considered for critical components of future metabolic studies.

  10. Rebuilding sources of linear tracers after atmospheric concentration measurements

    Directory of Open Access Journals (Sweden)

    J.-P. Issartel

    2003-01-01

    Full Text Available The identification of widespread sources of passive tracers out of atmospheric concentration measurements has become an important challenge of modern meteorology. The paper proposes some mathematical tracks to address the reconstruction of the complex space-time geometry of the sources of linear tracers. The methods are based upon the use of retroplumes. The inverse problem is addressed in a deterministic non statistical frame. The information obtained by local measurements is spread by introducing the concept of illumination. The constraint that the source is non negative is also addressed. The experimental source ETEX1 is rebuilt in order to evaluate an impulse response of the algorithms.

  11. Measurements of Contaminant Dispersion in ventilated Rooms by a Passive Tracer Gas Technique

    DEFF Research Database (Denmark)

    Heiselberg, Per; Bergsøe, Niels Christian

    During recent years the interest in the passive tracer gas technique has grown rapidly. The method has mainly been used in the field for measurements of air infiltration rates in buildings. This paper describes measurements of the contaminant dispersion in a ventilated room using a passive tracer...... gas technique and the results are compared with the results from a conventional method. Vertical profiles of concentration in the middle of the room have been measured at different ventilation air flow rates and different locations of the tracer gas source. The results showed good correspondence...... between the methods within an accuracy of ± 10- 15% in large parts of the room. In regions close to the tracer gas sources the differences were larger. The results gave at the same time recommendations for the use of the passive tracer gas technique for measurements of the air infiltration rates...

  12. Analysis of Carbon Monoxide in Blood

    Science.gov (United States)

    Huddle, Benjamin P.; Stephens, Joseph C.

    2003-04-01

    Forensic tests used to perform the qualitative and quantitative analyses of carbon monoxide in blood are described. The qualitative test uses the diffusion of CO, which is released from blood by reaction with H2SO4, into a PdCl2 solution in a Conway cell and the resultant formation of a palladium mirror. The quantitative analysis is based on the absorption of visible light by carboxyhemoglobin at 541 nm and reduced hemoglobin at 555 nm. Both procedures are suitable for undergraduate chemistry experiments.

  13. Measurements of Carbon Dioxide, Methane, and Other Related Tracers at High Spatial and Temporal Resolution in an Urban Environment

    Science.gov (United States)

    Forgeron, J.; Yasuhara, S.; Rella, C.; Jacobson, G. A.; Chiao, S.

    2012-12-01

    . The ratio between carbon dioxide and carbon monoxide is shown to vary over more than a factor of two from season to season or even from day to night, indicating rapid but frequent shifts in the balance between different carbon dioxide sources. Additional information is given by the carbon-13 signature and by acetylene, a fossil fuel combustion tracer that provides complimentary information to carbon monoxide. In spring and summer, the combined signal of the urban center and the surrounding biosphere and urban green space is explored. These methods show great promise for identifying, quantifying, and partitioning urban-ecological (carbon) emissions. Figure 1: The left graph shows the change in diurnal cycle of CO2 (with the traffic signal removed) over a five month period. The right graph is the transit CO2 signal from weekdays and weekends, showing clear weekday enhancement of transit emissions.

  14. Tracer tests in geothermal resource management

    OpenAIRE

    Axelsson G.

    2013-01-01

    Geothermal reinjection involves injecting energy-depleted fluid back into geothermal systems, providing an effective mode of waste-water disposal as well as supplementary fluid recharge. Cooling of production boreholes is one of the main disadvantages associated with reinjection, however. Tracer testing is an important tool for reinjection studies because tracer tests actually have a predictive power since tracer transport is orders of magnitude faster than cold-front advancement around reinj...

  15. The impacts of temperature on the absorption spectral lines of carbon monoxide

    Energy Technology Data Exchange (ETDEWEB)

    Guo Jianqiang; Xu Yuanze; Gao Xiaorong; Wang Li; Wang Zeyong, E-mail: jianqguo@home.swjtu.edu.cn [College of Physical Science and Technology, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China)

    2011-02-01

    In order to study the change of temperature on the effects of carbon monoxide absorption spectral lines, first of all proceed from the principle of absorption spectra, using theoretical analysis method, and the transmission and absorption database of the high-resolution molecular educed the carbon monoxide absorption spectrum intensity of spectral lines, integrated widening line type function and absorption coefficient concerned with temperature, then we got the change curve between carbon monoxide absorption spectrum intensity of spectral lines, integrated widening line type function and absorption coefficient with temperature by the numerical simulation of MATLAB, and analyzed and discussed the relationship between the temperature and them. The results showed that the temperature on the effects of carbon monoxide absorption spectral lines, especially on an Integrated widening line type function is complex, and different laser frequencies will also affect the relationship of the line type function and the absorption coefficient change with temperature, which has important reference value for the absorption and measurement of carbon in practical application.

  16. Effects of chemical modifications of heme on kinetics of carbon monoxide binding to free home

    Energy Technology Data Exchange (ETDEWEB)

    Sono, M.; McCray, J.A.; Asakura, T.

    1977-11-10

    The rates of carbon monoxide recombination to six different kinds of chemically modified heme with various substituents at positions 2 and 4 have been studied in the protein-free state (free heme) by the laser flash photolysis method in a mixture of ethylene glycol and 0.02 N NaOH (80:20, v/v) (80% ethylene glycol). The carbon monoxide combination rate constants to the various free hemes obtained in 80% ethylene glycol at 22/sup 0/ were 1.4, 2.1, 2.1, 3.7, 4.5, and 6.4 x 10/sup 7/ M/sup -1/ s/sup -1/ for 2,4-diformyl-, spirographis (2-formyl-4-vinyl-), isospirographis (2-vinyl-4-formyl-) proto-(2,4-divinyl-), deutero-(2,4-dihydrogen-), and meso-(2,4-diethyl-), hemes, respectively. This order of increase in carbon monoxide combination rate constants for these hemes correlates exactly with decrease in electron attractivity of heme side chains (i.e., increase in pK/sub 3/, basicity of nitrogen base of prophyrin) and is completely opposite to that obtained for carbon monoxide binding to these hemes reconstituted with apomyoglobin. Contrary to the results for myoglobin, the two isomers of monoformyl-monovinylheme exhibited similar optical properties and the same combination rate constant indicating that the differences in the optical and kinetic results observed in myoglobin are due to different interactions of these isomeric hemes with protein.

  17. MODELLING OF CARBON MONOXIDE AIR POLLUTION IN LARG CITIES BY EVALUETION OF SPECTRAL LANDSAT8 IMAGES

    Directory of Open Access Journals (Sweden)

    M. Hamzelo

    2015-12-01

    Full Text Available Air pollution in large cities is one of the major problems that resolve and reduce it need multiple applications and environmental management. Of The main sources of this pollution is industrial activities, urban and transport that enter large amounts of contaminants into the air and reduces its quality. With Variety of pollutants and high volume manufacturing, local distribution of manufacturing centers, Testing and measuring emissions is difficult. Substances such as carbon monoxide, sulfur dioxide, and unburned hydrocarbons and lead compounds are substances that cause air pollution and carbon monoxide is most important. Today, data exchange systems, processing, analysis and modeling is of important pillars of management system and air quality control. In this study, using the spectral signature of carbon monoxide gas as the most efficient gas pollution LANDSAT8 images in order that have better spatial resolution than appropriate spectral bands and weather meters،SAM classification algorithm and Geographic Information System (GIS , spatial distribution of carbon monoxide gas in Tehran over a period of one year from the beginning of 2014 until the beginning of 2015 at 11 map have modeled and then to the model valuation ،created maps were compared with the map provided by the Tehran quality comparison air company. Compare involved plans did with the error matrix and results in 4 types of care; overall, producer, user and kappa coefficient was investigated. Results of average accuracy were about than 80%, which indicates the fit method and data used for modeling.

  18. Modelling of Carbon Monoxide Air Pollution in Larg Cities by Evaluetion of Spectral LANDSAT8 Images

    Science.gov (United States)

    Hamzelo, M.; Gharagozlou, A.; Sadeghian, S.; Baikpour, S. H.; Rajabi, A.

    2015-12-01

    Air pollution in large cities is one of the major problems that resolve and reduce it need multiple applications and environmental management. Of The main sources of this pollution is industrial activities, urban and transport that enter large amounts of contaminants into the air and reduces its quality. With Variety of pollutants and high volume manufacturing, local distribution of manufacturing centers, Testing and measuring emissions is difficult. Substances such as carbon monoxide, sulfur dioxide, and unburned hydrocarbons and lead compounds are substances that cause air pollution and carbon monoxide is most important. Today, data exchange systems, processing, analysis and modeling is of important pillars of management system and air quality control. In this study, using the spectral signature of carbon monoxide gas as the most efficient gas pollution LANDSAT8 images in order that have better spatial resolution than appropriate spectral bands and weather meters،SAM classification algorithm and Geographic Information System (GIS ), spatial distribution of carbon monoxide gas in Tehran over a period of one year from the beginning of 2014 until the beginning of 2015 at 11 map have modeled and then to the model valuation ،created maps were compared with the map provided by the Tehran quality comparison air company. Compare involved plans did with the error matrix and results in 4 types of care; overall, producer, user and kappa coefficient was investigated. Results of average accuracy were about than 80%, which indicates the fit method and data used for modeling.

  19. Rapid Evaluation of the Severity and Prognosis of Acute Carbon Monoxide Poisoning

    Directory of Open Access Journals (Sweden)

    Z. N. Marupov

    2010-01-01

    Full Text Available Objective: to assess whether cardiointervalography (CIG might be used to define the health status of patients with carbon monoxide poisoning. Subjects and methods. The autonomic nervous system (ANS was studied in 114 patients aged 16 to 80 years with carbon monohydrate poisoning who were treated at the N. V. Sklifosovsky Research Institute of Emergency Care, Moscow, in 2004—2009. Cardiointervalographic readings were analyzed in relation to condition severity and disease outcome. Results. Within the first hours after carbon monoxide poisoning, the function of the ANS was found to be impaired, which was associated with the development of hypersym-pathicotonia caused by the increased activity of its sympathetic part and the decreased tone of the parasympathet-ic one. The magnitude of hypersympathicotonia depended on the severity of poisoning and the outcome of the disease. The preponderance of ANS parasympathetic part tone suggests disturbed adaptive and compensatory mechanisms and poor prognosis. Conclusion. Cardiointervalography is recommended for the objective evaluation of the severity of carbon monoxide poisoning and the efficiency of performed treatment and prediction of the outcome of the disease. Key words: carbon monoxide, autonomic nervous system, cardiointervalography, adaptive and compensatory mechanisms.

  20. Streamwise decrease of the 'unsteady' virtual velocity of gravel tracers

    Science.gov (United States)

    Klösch, Mario; Gmeiner, Philipp; Habersack, Helmut

    2017-04-01

    Gravel tracers are usually inserted and transported on top of the riverbed, before they disperse vertically and laterally due to periods of intense bedload, the passage of bed forms, lateral channel migration and storage on bars. Buried grains have a lower probability of entrainment, resulting in a reduction of overall mobility, and, on average, in a deceleration of the particles with distance downstream. As a consequence, the results derived from tracer experiments and their significance for gravel transport may depend on the time scale of the investigation period, complicating the comparison of results from different experiments. We developed a regression method, which establishes a direct link between the transport velocity and the unsteady flow variables to yield an 'unsteady' virtual velocity, while considering the tracer slowdown with distance downstream in the regression. For that purpose, the two parameters of a linear excess shear velocity formula (the critical shear velocity u*c and coefficient a) were defined as functions of the travelled distance since the tracer's insertion. Application to published RFID tracer data from the Mameyes River, Puerto Rico, showed that during the investigation period the critical shear velocity u*c of tracers representing the median bed particle diameter (0.11 m) increased from 0.36 m s-1 to 0.44 m s-1, while the coefficient a decreased from the dimensionless value of 4.22 to 3.53, suggesting a reduction of the unsteady virtual velocity at the highest shear velocity in the investigation period from 0.40 m s-1 to 0.08 m s-1. Consideration of the tracer slowdown improved the root mean square error of the calculated mean displacements of the median bed particle diameter from 8.82 m to 0.34 m. As in previous work these results suggest the need of considering the history of transport when deriving travel distances and travel velocities, depending on the aim of the tracer study. The introduced method now allows estimating the

  1. [Carbon monoxide poisoning by a heating system].

    Science.gov (United States)

    Dietz, Eric; Gehl, Axel; Friedrich, Peter; Kappus, Stefan; Petter, Franz; Maurer, Klaus; Püschel, Klaus

    2016-01-01

    A case of accidental carbon monoxide poisoning in several occupants of two neighboring residential buildings in Hamburg-Harburg (Germany) caused by a defective gas central heating system is described. Because of leaks in one of the residential buildings and the directly adjacent wall of the neighboring house, the gas could spread and accumulated in both residential buildings, which resulted in a highly dangerous situation. Exposure to the toxic gas caused mild to severe intoxication in 15 persons. Three victims died still at the site of the accident. Measures to protect the occupants were taken only with a great delay. As symptoms were unspecific, it was not realized that the various alarms given by persons involved in the accident were related to the same cause. In order to take appropriate measures in time it is indispensible to recognize, assess and check potential risks, which can be done by using carbon monoxide warning devices and performing immediate COHb measurements with special pulse oximeters on site. Moreover, the COHb content in the blood should be routinely determined in all patients admitted to an emergency department with unspecific symptoms.

  2. Observations of iodine monoxide columns from satellite

    Directory of Open Access Journals (Sweden)

    A. Schönhardt

    2008-02-01

    Full Text Available Iodine species in the troposphere are linked to ozone depletion and new particle formation. In this study, a full year of iodine monoxide (IO columns retrieved from measurements of the SCIAMACHY satellite instrument is presented, coupled with a discussion of their uncertainties and the detection limits. The largest amounts of IO are found near springtime in the Antarctic. A seasonal variation of iodine monoxide in Antarctica is revealed with high values in springtime, slightly less IO in the summer period and again larger amounts in autumn. In winter, no elevated IO levels are found in the areas accessible to satellite measurements. This seasonal cycle is in good agreement with recent ground-based measurements in Antarctica. In the Arctic region, no elevated IO levels were found in the period analysed. This implies that different conditions with respect to iodine release exist in the two Polar Regions. To investigate possible release mechanisms, comparisons of IO columns with those of tropospheric BrO, and ice coverage are described and discussed. Some parallels and interesting differences between IO and BrO temporal and spatial distributions are identified. Overall, the large spatial coverage of satellite retrieved IO data and the availability of a long-term dataset provide new insight about the abundances and distributions of iodine compounds in the troposphere.

  3. Hypervalence in monoxides and dioxides of superalkali clusters

    Science.gov (United States)

    Cochran, Elizabeth; Meloni, Giovanni

    2014-05-01

    F2Li3, a superalkali cluster, is characterized as having a lower adiabatic ionization energy than its elemental alkali counterpart and, coupled with the presence of complex molecular orbitals, suggests promise for novel bonding possibilities. CBS-QB3 composite method was used to study three distinct cluster isomers, as well as their cationic (+1) and anionic (-1) species, to identify energetic trends and observe geometric changes. Oxides were then generated from these clusters, of which three distinct monoxides and nine dioxides were obtained upon structure optimization. Identical calculations were performed for the oxide species and their charged counterparts. Some of the most stable oxides produced appear to possess hypervalent lithium and oxygen atoms, forming unique structures with exceptional stability.

  4. ROLE OF ENDOGENOUS CARBON MONOXIDE IN ENDOTOXIN SHOCK

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Objective. To study the role of endogenous carbon monoxide (CO) in endotoxin shock. Methods. The changes of CO levels and the effects of zinc protoporphyrin IX (ZnPP),an inhibitor of heme-oxygenase (HO), in endotoxin shock and the efficacy of hemin,an inducer of HO were investigated.Results. The plasma CO levels were found to be significantly increased during the course of endotoxin shock. Injection of ZnPP was shown to abrogate the endotoxin-induced hypotension and metabolic derangements markedly. Administration of hemin to healthy rabbits revealed the hypotension and metabolic derangements similar to the animals given endotoxin.Conclusion.CO is a newly found endogenously produced mediator which may play an important role in the pathogenesis of endotoxin shock.

  5. ROLE OF ENDOGENOUS CARBON MONOXIDE IN ENDOTOXIN SHOCK

    Institute of Scientific and Technical Information of China (English)

    史源; 李华强; 潘捷; 覃世文; 潘凤; 蒋东波; 沈际皋

    2000-01-01

    Objective. To study the role of endogenous carbon monoxide (CO) in endotoxin shock. Methods. The changes of CO levels and the effects of zinc protoporphyrin IX (ZnPP), an inhibitor of hemeoxygenase (HO), in endotoxin shock and the efficacy of heroin, an inducer of HO were investigated. Results. The plasma CO levels were found to be significantly increased during the comse of endotoxin shock. Injection of ZnPP was shown to abrogate the endotoxin-induced hypotension and metabolic derangements markedly. Administration of hemin to healthy rabbits revealed the hypotension and metabolic derangements similar to the animsls given endotoxin. Conclusion. CO is a newly found endogenously produced mediator which may play an important role in the pathogenesis of endotoxin shock.

  6. How well do different tracers constrain the firn diffusivity profile?

    Directory of Open Access Journals (Sweden)

    C. M. Trudinger

    2013-02-01

    Full Text Available Firn air transport models are used to interpret measurements of the composition of air in firn and bubbles trapped in ice in order to reconstruct past atmospheric composition. The diffusivity profile in the firn is usually calibrated by comparing modelled and measured concentrations for tracers with known atmospheric history. However, in most cases this is an under-determined inverse problem, often with multiple solutions giving an adequate fit to the data (this is known as equifinality. Here we describe a method to estimate the firn diffusivity profile that allows multiple solutions to be identified, in order to quantify the uncertainty in diffusivity due to equifinality. We then look at how well different combinations of tracers constrain the firn diffusivity profile. Tracers with rapid atmospheric variations like CH3CCl3, HFCs and 14CO2 are most useful for constraining molecular diffusivity, while &delta:15N2 is useful for constraining parameters related to convective mixing near the surface. When errors in the observations are small and Gaussian, three carefully selected tracers are able to constrain the molecular diffusivity profile well with minimal equifinality. However, with realistic data errors or additional processes to constrain, there is benefit to including as many tracers as possible to reduce the uncertainties. We calculate CO2 age distributions and their spectral widths with uncertainties for five firn sites (NEEM, DE08-2, DSSW20K, South Pole 1995 and South Pole 2001 with quite different characteristics and tracers available for calibration. We recommend moving away from the use of a firn model with one calibrated parameter set to infer atmospheric histories, and instead suggest using multiple parameter sets, preferably with multiple representations of uncertain processes, to assist in quantification of the uncertainties.

  7. How well do different tracers constrain the firn diffusivity profile?

    Directory of Open Access Journals (Sweden)

    C. M. Trudinger

    2012-07-01

    Full Text Available Firn air transport models are used to interpret measurements of the composition of air in firn and bubbles trapped in ice in order to reconstruct past atmospheric composition. The diffusivity profile in the firn is usually calibrated by comparing modelled and measured concentrations for tracers with known atmospheric history. However, in some cases this is an under-determined inverse problem, often with multiple solutions giving an adequate fit to the data (this is known as equifinality. Here we describe a method to estimate the firn diffusivity profile that allows multiple solutions to be identified, in order to quantify the uncertainty in diffusivity due to equifinality. We then look at how well different combinations of tracers constrain the firn diffusivity profile. Tracers with rapid atmospheric variations like CH3CCl3, HFCs and 14CO2 are most useful for constraining molecular diffusivity, while δ15N2 is useful for constraining parameters related to convective mixing near the surface. When errors in the observations are small and Gaussian, three carefully selected tracers are able to constrain the molecular diffusivity profile well with minimal equifinality. However, with realistic data errors or additional processes to constrain, there is benefit to including as many tracers as possible to reduce the uncertainties. We calculate CO2 age distributions and their spectral widths with uncertainties for five firn sites (NEEM, DE08-2, DSSW20K, South Pole 1995 and South Pole 2001 with quite different characteristics and tracers available for calibration. We recommend moving away from the use of a single firn model with one calibrated parameter set to infer atmospheric histories, and instead suggest using multiple parameter sets, preferably with multiple representations of uncertain processes, to allow quantification of the uncertainties.

  8. Nitric oxide and carbon monoxide diffusing capacity of the lung

    NARCIS (Netherlands)

    Lee, I. van der

    2006-01-01

    The single breath diffusion capacity of the lung for carbon monoxide (DLCO) is measure for gas uptake by the lung, and consists of a membrane and a vascular component. Nitric oxide (NO) binds 400 times faster to hemoglobin than carbon monoxide, thus the uptake of NO by the blood is very large.

  9. Nitric oxide and carbon monoxide diffusing capacity of the lung

    NARCIS (Netherlands)

    Lee, I. van der

    2006-01-01

    The single breath diffusion capacity of the lung for carbon monoxide (DLCO) is measure for gas uptake by the lung, and consists of a membrane and a vascular component. Nitric oxide (NO) binds 400 times faster to hemoglobin than carbon monoxide, thus the uptake of NO by the blood is very large. There

  10. Fatal carbon monoxide intoxication after acetylene gas welding of pipes.

    Science.gov (United States)

    Antonsson, Ann-Beth; Christensson, Bengt; Berge, Johan; Sjögren, Bengt

    2013-06-01

    Acetylene gas welding of district heating pipes can result in exposure to high concentrations of carbon monoxide. A fatal case due to intoxication is described. Measurements of carbon monoxide revealed high levels when gas welding a pipe with closed ends. This fatality and these measurements highlight a new hazard, which must be promptly prevented.

  11. Real World of Industrial Chemistry: Organic Chemicals from Carbon Monoxide.

    Science.gov (United States)

    Kolb, Kenneth E.; Kolb, Doris

    1983-01-01

    Carbon Monoxide obtained from coal may serve as the source for a wide variety of organic compounds. Several of these compounds are discussed, including phosgene, benzaldehyde, methanol, formic acid and its derivatives, oxo aldehydes, acrylic acids, and others. Commercial reactions of carbon monoxide are highlighted in a table. (JN)

  12. Tracer-Test Planning Using the Efficient Hydrologic Tracer-Test Design (Ehtd) Program (2003)

    Science.gov (United States)

    Hydrological tracer testing is the most reliable diagnostic technique available for establishing flow trajectories and hydrologic connections and for determining basic hydraulic and geometric parameters necessary for establishing operative solute-transport processes. Tracer-test ...

  13. Search of medical literature for indoor carbon monoxide exposure

    Energy Technology Data Exchange (ETDEWEB)

    Brennan, T.; Ivanovich, M.

    1995-12-01

    This report documents a literature search on carbon monoxide. The search was limited to the medical and toxicological databases at the National Library of Medicine (MEDLARS). The databases searched were Medline, Toxline and TOXNET. Searches were performed using a variety of strategies. Combinations of the following keywords were used: carbon, monoxide, accidental, residential, occult, diagnosis, misdiagnosis, heating, furnace, and indoor. The literature was searched from 1966 to the present. Over 1000 references were identified and summarized using the following abbreviations: The major findings of the search are: (1) Acute and subacute carbon monoxide exposures result in a large number of symptoms affecting the brain, kidneys, respiratory system, retina, and motor functions. (2) Acute and subacute carbon monoxide (CO) poisonings have been misdiagnosed on many occasions. (3) Very few systematic investigations have been made into the frequency and consequences of carbon monoxide poisonings.

  14. Electrochemical oxidation of carbon monoxide: from platinum single crystals to low temperature fuel cells catalysts. Part I: Carbon monoxide oxidation onto low index platinum single crystals

    Directory of Open Access Journals (Sweden)

    PHILIP N. ROSS JR

    2001-12-01

    Full Text Available The electrochemical oxidation of carbon monoxide and the interfacial structure of the CO adlayer (COads on platinum low index single crystals, Pt(111, Pt(100 and two reconstruction of Pt(110, were examined using the rotation disk electrode method in combination with the in situ surface X-ray diffraction scattering technique. The mechanism of CO oxidation is discussed on the basis of the findings that, depending on the potential, two energetic states of COads exist on the platinum surfaces. Thus, at lower potentials, weakly bonded states (COads,w and at higher potentials strongly bonded states (COads,s are formed. The mechanism of the oxidation of hydrogen-carbon monoxide mixtures is also proposed.

  15. Measurements of methane emissions from natural gas gathering facilities and processing plants: measurement methods

    Directory of Open Access Journals (Sweden)

    J. R. Roscioli

    2014-12-01

    Full Text Available Increased natural gas production in recent years has spurred intense interest in methane (CH4 emissions associated with its production, gathering, processing, transmission and distribution. Gathering and processing facilities (G&P facilities are unique in that the wide range of gas sources (shale, coal-bed, tight gas, conventional, etc. results in a wide range of gas compositions, which in turn requires an array of technologies to prepare the gas for pipeline transmission and distribution. We present an overview and detailed description of the measurement method and analysis approach used during a 20-week field campaign studying CH4 emissions from the natural gas G&P facilities between October 2013 and April 2014. Dual tracer flux measurements and onsite observations were used to address the magnitude and origins of CH4 emissions from these facilities. The use of a second tracer as an internal standard revealed plume-specific uncertainties in the measured emission rates of 20–47%, depending upon plume classification. Combining downwind methane, ethane (C2H6, carbon monoxide (CO, carbon dioxide (CO2, and tracer gas measurements with onsite tracer gas release allows for quantification of facility emissions, and in some cases a more detailed picture of source locations.

  16. Tracers for Characterizing Enhanced Geothermal Systems

    Energy Technology Data Exchange (ETDEWEB)

    Karen Wright; George Redden; Carl D. Palmer; Harry Rollins; Mark Stone; Mason Harrup; Laurence C. Hull

    2010-02-01

    Information about the times of thermal breakthrough and subsequent rates of thermal drawdown in enhanced geothermal systems (EGS) is necessary for reservoir management, designing fracture stimulation and well drilling programs, and forecasting economic return. Thermal breakthrough in heterogeneous porous media can be estimated using conservative tracers and assumptions about heat transfer rates; however, tracers that undergo temperature-dependent changes can provide more detailed information about the thermal profile along the flow path through the reservoir. To be effectively applied, the thermal reaction rates of such temperature sensitive traces must be well characterized for the range of conditions that exist in geothermal systems. Reactive tracers proposed in the literature include benzoic and carboxylic acids (Adams) and organic esters and amides (Robinson et al.); however, the practical temperature range over which these tracers can be applied (100-275°C) is somewhat limited. Further, for organic esters and amides, little is known about their sorption to the reservoir matrix and how such reactions impact data interpretation. Another approach involves tracers where the reference condition is internal to the tracer itself. Two examples are: 1) racemization of polymeric amino acids, and 2) mineral thermoluminescence. In these cases internal ratios of states are measured rather than extents of degradation and mass loss. Racemization of poly-L-lactic acid (for example) is temperature sensitive and therefore can be used as a temperature-recording tracer depending on the rates of racemization and stability of the amino acids. Heat-induced quenching of thermoluminescence of pre-irradiated LiF can also be used. To protect the tracers from alterations (extraneous reactions, dissolution) in geothermal environments we are encapsulating the tracers in core-shell colloidal structures that will subsequently be tested for their ability to be transported and to protect the

  17. Tracers for Characterizing Enhanced Geothermal Systems

    Energy Technology Data Exchange (ETDEWEB)

    Karen Wright; George Redden; Carl D. Palmer; Harry Rollins; Mark Stone; Mason Harrup; Laurence C. Hull

    2010-02-01

    Information about the times of thermal breakthrough and subsequent rates of thermal drawdown in enhanced geothermal systems (EGS) is necessary for reservoir management, designing fracture stimulation and well drilling programs, and forecasting economic return. Thermal breakthrough in heterogeneous porous media can be estimated using conservative tracers and assumptions about heat transfer rates; however, tracers that undergo temperature-dependent changes can provide more detailed information about the thermal profile along the flow path through the reservoir. To be effectively applied, the thermal reaction rates of such temperature sensitive traces must be well characterized for the range of conditions that exist in geothermal systems. Reactive tracers proposed in the literature include benzoic and carboxylic acids (Adams) and organic esters and amides (Robinson et al.); however, the practical temperature range over which these tracers can be applied (100-275°C) is somewhat limited. Further, for organic esters and amides, little is known about their sorption to the reservoir matrix and how such reactions impact data interpretation. Another approach involves tracers where the reference condition is internal to the tracer itself. Two examples are: 1) racemization of polymeric amino acids, and 2) mineral thermoluminescence. In these cases internal ratios of states are measured rather than extents of degradation and mass loss. Racemization of poly-L-lactic acid (for example) is temperature sensitive and therefore can be used as a temperature-recording tracer depending on the rates of racemization and stability of the amino acids. Heat-induced quenching of thermoluminescence of pre-irradiated LiF can also be used. To protect the tracers from alterations (extraneous reactions, dissolution) in geothermal environments we are encapsulating the tracers in core-shell colloidal structures that will subsequently be tested for their ability to be transported and to protect the

  18. Unit vent airflow measurements using a tracer gas technique

    Energy Technology Data Exchange (ETDEWEB)

    Adams, D.G. [Union Electric Company, Fulton, MO (United States); Lagus, P.L. [Lagus Applied Technology, Inc., San Diego, CA (United States); Fleming, K.M. [NCS Corp., Columbus, OH (United States)

    1997-08-01

    An alternative method for assessing flowrates that does not depend on point measurements of air flow velocity is the constant tracer injection technique. In this method one injects a tracer gas at a constant rate into a duct and measures the resulting concentration downstream of the injection point. A simple equation derived from the conservation of mass allows calculation of the flowrate at the point of injection. Flowrate data obtained using both a pitot tube and a flow measuring station were compared with tracer gas flowrate measurements in the unit vent duct at the Callaway Nuclear Station during late 1995 and early 1996. These data are presented and discussed with an eye toward obtaining precise flowrate data for release rate calculations. The advantages and disadvantages of the technique are also described. In those test situations for which many flowrate combinations are required, or in large area ducts, a tracer flowrate determination requires fewer man-hours than does a conventional traverse-based technique and does not require knowledge of the duct area. 6 refs., 10 figs., 6 tabs.

  19. Estimation of Recharge from Long-Term Monitoring of Saline Tracer Transport Using Electrical Resistivity Tomography

    DEFF Research Database (Denmark)

    Haarder, Eline Bojsen; Jensen, Karsten Høgh; Binley, Andrew;

    2015-01-01

    The movement of a saline tracer added to the soil surface was monitored in the unsaturated zone using cross-borehole electrical resistivity tomography (ERT) and subjected to natural rainfall conditions. The ERT data were inverted and corrected for subsurface temperature changes, and spatial moment...... methods. In September 2011, a saline tracer was added across a 142-m2 area at the surface at an application rate mimicking natural infiltration. The movement of the saline tracer front was monitored using cross-borehole electrical resistivity tomography (ERT); data were collected on a daily to weekly...... basis and continued for 1 yr after tracer application. The ERT data were inverted and corrected for temperature changes in the subsurface, and spatial moment analysis was used to calculate the tracer mass, position of the center of mass, and thereby the downwardly recharging flux. The recovered mass...

  20. Evidence for horizontal gene transfer of anaerobic carbon monoxide dehydrogenases

    Directory of Open Access Journals (Sweden)

    Stephen eTechtmann

    2012-04-01

    Full Text Available Carbon monoxide (CO is commonly known as a toxic gas, yet it is used by both aerobic and anaerobic bacteria and many archaea. In this study, we determined the prevalence of anaerobic carbon monoxide dehydrogenases (anaerobic CODHs, or [Ni,Fe]-CODHs in currently available genomic sequence databases. More than 6% (185 genomes out of 2887 bacterial and archaeal genome sequences in the IMG database possess at least one gene encoding [Ni,Fe]-CODH, the key enzyme for anaerobic CO utilization. The phylogenetic study of this extended protein family revealed nine distinct clades of [Ni,Fe]-CODHs. These clades consisted of [Ni,Fe]-CODHs that, while apparently monophyletic within the clades, were encoded by microorganisms of disparate phylogeny, based on 16S rRNA sequences, and widely ranging physiology. Following this discovery, it was therefore of interest to examine the extent and possible routes of horizontal gene transfer (HGT affecting [Ni,Fe]-CODH genes and gene clusters that include [Ni,Fe]-CODHs.The genome sequence of the extreme thermophile Thermosinus carboxydivorans was used as a case study for HGT. The [Ni,Fe]-CODH operon of T. carboxydivorans differs from its whole genome in its G+C content by 8.2 mol%. Here, we apply statistical methods to establish acquisition by T. carboxydivorans of the gene cluster including [Ni,Fe]-CODH via HGT. Analysis of tetranucleotide frequency and codon usage with application of the Kullback-Leibler divergence metric showed that the [Ni,Fe]-CODH-1 operon of T. carboxidyvorans is quite dissimilar to the whole genome. Using the same metrics, the T. carboxydivorans [Ni,Fe]-CODH-1 operon is highly similar to the genome of the phylogenetically distant anaerobic carboxydotroph Carboxydothermus hydrogenoformans. These results allow to assume recent HTG of the gene cluster from a relative of C. hydrogenoformans to T. carboxydivorans or a more ancient transfer from a C. hydrogenoformans ancestor to a T. carboxydivorans

  1. The fluorescent tracer experiment on Holiday Beach near Mugu Canyon, Southern California

    Science.gov (United States)

    Kinsman, Nicole; Xu, J. P.

    2012-01-01

    After revisiting sand tracer techniques originally developed in the 1960s, a range of fluorescent coating formulations were tested in the laboratory. Explicit steps are presented for the preparation of the formulation evaluated to have superior attributes, a thermoplastic pigment/dye in a colloidal mixture with a vinyl chloride/vinyl acetate copolymer. In September 2010, 0.59 cubic meters of fluorescent tracer material was injected into the littoral zone about 4 kilometers upcoast of Mugu submarine canyon in California. The movement of tracer was monitored in three dimensions over the course of 4 days using manual and automated techniques. Detailed observations of the tracer's behavior in the coastal zone indicate that this tracer successfully mimicked the native beach sand and similar methods could be used to validate models of tracer movement in this type of environment. Recommendations including how to time successful tracer studies and how to scale the field of view of automated camera systems are presented along with the advantages and disadvantages of the described tracer methodology.

  2. The Copenhagen tracer experiments: Reporting of measurements

    DEFF Research Database (Denmark)

    Gryning, Sven-Erik; Lyck, E.

    2002-01-01

    buoyancy from a tower at a height of 115 meters and then collected 2-3 meters above ground-level at positions in up to three crosswind arcs of tracer sampling units, positioned 2-6 km from the point of release. Three consecutive 20 min averaged tracer concentrations were measured, allowing for a total...

  3. Projection of North Atlantic Oscillation and its effect on tracer transport

    Science.gov (United States)

    Bacer, Sara; Christoudias, Theodoros; Pozzer, Andrea

    2016-12-01

    The North Atlantic Oscillation (NAO) plays an important role in the climate variability of the Northern Hemisphere, with significant consequences on long-range pollutant transport. We investigate the evolution of pollutant transport in the 21st century influenced by the NAO under a global climate change scenario. We use a free-running simulation performed by the ECHAM/MESSy Atmospheric Chemistry (EMAC) model coupled with the ocean general circulation model MPIOM, covering the period from 1950 until 2100. Similarly to other works, the model shows a future northeastward shift of the NAO centres of action and a weak positive trend of the NAO index (over 150 years). Moreover, we find that NAO trends (computed over periods shorter than 30 years) will continue to oscillate between positive and negative values in the future. To investigate the NAO effects on transport we consider carbon monoxide tracers with exponential decay and constant interannual emissions. We find that at the end of the century, the south-western Mediterranean and northern Africa will, during positive NAO phases, see higher pollutant concentrations with respect to the past, while a wider part of northern Europe will, during positive NAO phases, see lower pollutant concentrations. Such results are confirmed by the changes observed in the future for tracer concentration and vertically integrated tracer transport, differentiating the cases of "high NAO" and "low NAO" events.

  4. Effect of tracer buoyancy on tracer experiments conducted in fractured crystalline bedrock

    Science.gov (United States)

    Becker, Matthew W.

    2003-02-01

    Tracer buoyancy has been shown to influence breakthrough from two-well tracer experiments conducted in porous media. Two-well tracer experiments are presented from fractured crystalline bedrock, in which the specific gravity of the tracer injectate varied from 1.0002 to 1.0133. Under the forced hydraulic conditions imposed, no difference in breakthrough was noted for the three experiments. These results show that even relatively dense tracer injectate solutions may have an insignificant effect on breakthrough when imposed gradients are sufficiently large.

  5. The Art of Tomographic Tracer Tests

    Science.gov (United States)

    Cirpka, O. A.; Leven, C.; Doro, K. O.; Sanchez-Leon, E. E.

    2015-12-01

    In tracer tomography several tracer tests are performed within an aquifer and breakthrough curves are observed at multiple observation points. In the analysis, hydraulic conductivity is estimated as spatially variable, 3-D field subject to some smoothness constraint. Coupled flow and transport models using this conductivity fields are requested to meet observed tracer data. The approach can be combined with hydraulic tomography.We have performed hydraulic-tomography and tracer-tomography tests using heat and fluorescein as tracers at a field site close to Tübingen, Germany. The aquifer consists of 8-9m alluvials sands and gravels overlain by 1-2m alluvial fines. The hydraulic setup consists of a forced flow field between an injection/extraction well couple, embedded in the forced flow field of another well couple. By turning injection to extraction wells, and vice versa, two different flow fields were considered. Injection wells were separated into several sections by packers, and water was injected into each section proportional to its transmissivity. The water injected into one of the sections contained the tracer. Multi-level observation wells were equiped with thermometers (for heat-tracer tests), on-line fluoremeters (for teh dye tracers), and pressure transducers. Processing of the breakthrough curves included data cleaning, non-parametric deconvolution, and calculation of temperal moments of the estimated transfer functions.The joint inversion of hydraulic-head measurements and temporal moments of heat-tracer transfer functions was done by the quasi-linear geostatistical approach on a computing cluster. As alternative, we directly invert the time series (without temporal moments) by Ensemble-Kalman filtering.The high diffusion coefficient of temperature diminishes the penetration of the heat-tracer into the aquifer, which can partially be compensated by reverting the flow field and repeating the tracer tests. In tests with fluorscent tracers the signal

  6. Reduction of carbon monoxide. Past research summary

    Energy Technology Data Exchange (ETDEWEB)

    Schrock, R.R.

    1981-10-01

    Research programs for the year on the preparation, characterization, and reactions of binuclear tantalum complexes are described. All evidence to date suggest the following of these dimeric molecules: (1) the dimer does not break into monomers under mild conditions; (2) intermolecular hydride exchange is not negligible, but it is slow; (3) intermolecular non-ionic halide exchange is fast; (4) the ends of the dimers can rotate partially with respect to one another. The binuclear tantalum hydride complexes were found to react with carbon monoxide to give a molecule which is the only example of reduction of CO by a transition metal hydride to give a complex containing a CHO ligand. Isonitrides also reacted in a similar manner with dimeric tantalum hydride. (ATT)

  7. Correlative microscopy of densely labeled projection neurons using neural tracers.

    Science.gov (United States)

    Oberti, Daniele; Kirschmann, Moritz A; Hahnloser, Richard H R

    2010-01-01

    Three-dimensional morphological information about neural microcircuits is of high interest in neuroscience, but acquiring this information remains challenging. A promising new correlative technique for brain imaging is array tomography (Micheva and Smith, 2007), in which series of ultrathin brain sections are treated with fluorescent antibodies against neurotransmitters and synaptic proteins. Treated sections are repeatedly imaged in the fluorescence light microscope (FLM) and then in the electron microscope (EM). We explore a similar correlative imaging technique in which we differentially label distinct populations of projection neurons, the key routers of electrical signals in the brain. In songbirds, projection neurons can easily be labeled using neural tracers, because the vocal control areas are segregated into separate nuclei. We inject tracers into areas afferent and efferent to the main premotor area for vocal production, HVC, to retrogradely and anterogradely label different classes of projection neurons. We optimize tissue preparation protocols to achieve high fluorescence contrast in the FLM and good ultrastructure in the EM (using osmium tetroxide). Although tracer fluorescence is lost during EM preparation, we localize the tracer molecules after fixation and embedding by using fluorescent antibodies against them. We detect signals mainly in somata and dendrites, allowing us to classify synapses within a single ultrathin section as belonging to a particular type of projection neuron. The use of our method will be to provide statistical information about connectivity among different neuron classes, and to elucidate how signals in the brain are processed and routed among different areas.

  8. Correlative microscopy of densely labeled projection neurons using neural tracers

    Directory of Open Access Journals (Sweden)

    Daniele Oberti

    2010-06-01

    Full Text Available Three-dimensional morphological information about neural microcircuits is of high interest in neuroscience, but acquiring this information remains challenging. A promising new correlative technique for brain imaging is array tomography (Micheva and Smith, 2007, in which series of ultrathin brain sections are treated with fluorescent antibodies against neurotransmitters and synaptic proteins. Treated sections are repeatedly imaged in the fluorescence light microscope (FLM and then in the electron microscope (EM. We explore a similar correlative imaging technique in which we differentially label distinct populations of projection neurons, the key routers of electrical signals in the brain. In songbirds, projection neurons can easily be labeled using neural tracers, because the vocal control areas are segregated into separate nuclei. We inject tracers into areas afferent and efferent to the main premotor area for vocal production, HVC, to retrogradely and anterogradely label different classes of projection neurons. We optimize tissue preparation protocols to achieve high fluorescence contrast in the FLM and good ultrastructure in the EM (using osmium tetroxide. Although tracer fluorescence is lost during EM preparation, we localize the tracer molecules after fixation and embedding by using fluorescent antibodies against them. We detect signals mainly in somata and dendrites, allowing us to classify synapses within a single ultrathin section as belonging to a particular type of projection neuron. The use of our method will be to provide statistical information about connectivity among different neuron classes, and to elucidate how signals in the brain are processed and routed among different areas.

  9. The determination of mass of metabolites with tracers

    Energy Technology Data Exchange (ETDEWEB)

    Katz, J. (Cedars-Sinai Medical Center, Los Angeles, CA (USA))

    1989-08-01

    Application of tracers in vivo for the determination of replacement and mass of bloodborne compounds at steady state is discussed. Theory and methods to determine mass with tracers (total amount of compound-tracee-within the body) for compartmental and noncompartmental systems are presented, and their limitations examined. Methods to derive mass from the specific activity curves after bolus injection or infusion of tracer are described using graphic procedures or by equations using the parameters of exponential curves. The relationship between assumed models and the interpretation of tracer data is examined. The determination of both replacement (appearance, which equals utilization at steady state) and mass of most compounds present in both extracellular and intracellular fluids (such as lactate and amino acids) requires the application of the A-V mode for tracer administration and sampling of blood. Recycling of carbon affects the determination of mass with {sup 14}C. Estimates of true mass are provided with tritium-labeled compounds, even when tritium loss is by exchange with protons or through futile cycling. Estimates of the amount (body mass) of lactate, alanine, glutamate, and proline obtained with tritium-labeled compounds are presented. Most of these masses are intracellular. The concentration of lactate in tissues equals or is greater, and that of amino acids much greater than that in plasma. Hence, the so-called distribution space for these compounds, calculated conventionally by dividing mass by plasma concentration, would appear to be equal to or greater than the body water of lactate, and several liters per kilogram for amino acids.

  10. Effect of N-Acetylcysteine in Protecting from Simultaneous Noise and Carbon Monoxide Induced Hair Cell Loss

    Directory of Open Access Journals (Sweden)

    Akram Pourbakht

    2011-06-01

    Full Text Available Background and Aim: N-acetylcysteine, a glutathione precursor and reactive oxygen species scavenger, is reported to be effective in reducing noise-induced hearing loss. Many workers in industry are exposed simultaneously to noise and chemical pollutants such as carbon monoxide. We investigated effectiveness of N-acetylcysteine in protecting the cochlea from simultaneous noise and carbon monoxide damages.Methods: Twelve rabbits were exposed simeltaneously to 100 dB sound pressure level of broad band noise and carbon monoxide 8 hours a day for 5 days. One hour before exposure, experimental group received 325 mg/kg of N-acetylcysteine while normal saline was administered for the control group. The protective effect of N-acetylcysteine was evaluated 3 weeks after exposure by histological assessment of the hair cells.Results: Simultaneous exposure to noise and carbon monoxide resulted in a considerable damage to the outer hair cells; however, the inner hair cells and the pillar cells remained intact. Use of N-acetylcysteine in the experimental group significantly reduced the extent of outer hair cell loss.Conclusion: N-acetylcysteine attenuates simultaneous noise and carbon monoxide induced hair cell damage in rabbits.

  11. Accuracy of a new bedside method for estimation of circulating blood volume

    DEFF Research Database (Denmark)

    Christensen, P; Waever Rasmussen, J; Winther Henneberg, S

    1993-01-01

    To evaluate the accuracy of a modification of the carbon monoxide method of estimating the circulating blood volume.......To evaluate the accuracy of a modification of the carbon monoxide method of estimating the circulating blood volume....

  12. Hydrogen bonding of formamide, urea, urea monoxide and their thio-analogs with water and homodimers

    Indian Academy of Sciences (India)

    Damanjit Kaur; Shweta Khanna

    2014-11-01

    Ab initio and DFT methods have been employed to study the hydrogen bonding ability of formamide, urea, urea monoxide, thioformamide, thiourea and thiourea monoxide with one water molecule and the homodimers of the selected molecules. The stabilization energies associated with themonohydrated adducts and homodimers’ formation were evaluated at B3LYP/6-311++G** and MP2/6-311++G∗∗ levels. The energies were corrected for zero-point vibrational energies and basis set superposition error using counterpoise method. Atoms in molecules study has been carried out in order to characterize the hydrogen bonds through the changes in electron density and laplacian of electron density. A natural energy decomposition and natural bond orbital analysis was performed to understand the nature of hydrogen bonding.

  13. Comparison of three magnetic nanoparticle tracers for sentinel lymph node biopsy in an in vivo porcine model

    Directory of Open Access Journals (Sweden)

    Pouw JJ

    2015-02-01

    Full Text Available Joost J Pouw,1,* Muneer Ahmed,2,* Bauke Anninga,2 Kimberley Schuurman,1 Sarah E Pinder,2 Mieke Van Hemelrijck,3 Quentin A Pankhurst,4,5 Michael Douek,2 Bennie ten Haken1 1MIRA Institute for Biomedical Technology and Technical Medicine, University of Twente, Enschede, the Netherlands; 2Research Oncology, Division of Cancer Studies, King’s College London, Guy’s Hospital, London, UK; 3Cancer Epidemiology Group, Division of Cancer Studies, King’s College London, London, UK; 4Healthcare Biomagnetics Laboratory, University College London, London, UK; 5Institute of Biomedical Engineering, University College London, London, UK *These authors contributed equally to this work Introduction: Breast cancer staging with sentinel lymph node biopsy relies on the use of radioisotopes, which limits the availability of the procedure worldwide. The use of a magnetic nanoparticle tracer and a handheld magnetometer provides a radiation-free alternative, which was recently evaluated in two clinical trials. The hydrodynamic particle size of the used magnetic tracer differs substantially from the radioisotope tracer and could therefore benefit from optimization. The aim of this study was to assess the performance of three different-sized magnetic nanoparticle tracers for sentinel lymph node biopsy within an in vivo porcine model.Materials and methods: Sentinel lymph node biopsy was performed within a validated porcine model using three magnetic nanoparticle tracers, approved for use in humans (ferumoxytol, with hydrodynamic diameter dH =32 nm; Sienna+®, dH =59 nm; and ferumoxide, dH =111 nm, and a handheld magnetometer. Magnetometer counts (transcutaneous and ex vivo, iron quantification (vibrating sample magnetometry, and histopathological assessments were performed on all ex vivo nodes.Results: Transcutaneous “hotspots” were present in 12/12 cases within 30 minutes of injection for the 59 nm tracer, compared to 7/12 for the 32 nm tracer and 8/12 for

  14. Tracer design for magnetic particle imaging (invited).

    Science.gov (United States)

    Ferguson, R Matthew; Khandhar, Amit P; Krishnan, Kannan M

    2012-04-01

    Magnetic particle imaging (MPI) uses safe iron oxide nanoparticle tracers to offer fundamentally new capabilities for medical imaging, in applications as vascular imaging and ultra-sensitive cancer therapeutics. MPI is perhaps the first medical imaging platform to intrinsically exploit nanoscale material properties. MPI tracers contain magnetic nanoparticles whose tunable, size-dependent magnetic properties can be optimized by selecting a particular particle size and narrow size-distribution. In this paper we present experimental MPI measurements acquired using a homemade MPI magnetometer: a zero-dimensional MPI imaging system designed to characterize tracer performance by measuring the derivative of the time-varying tracer magnetization, M'(H(t)), at a driving frequency of 25 kHz. We show that MPI performance is optimized by selecting phase-pure magnetite tracers of a particular size and narrow size distribution; in this work, tracers with 20 nm median diameter, log-normal distribution shape parameter, σ(v), equal to 0.26, and hydrodynamic diameter equal to 30 nm showed the best performance. Furthermore, these optimized MPI tracers show 4 × greater signal intensity (measured at the third harmonic) and 20% better spatial resolution compared with commercial nanoparticles developed for MRI.

  15. Assessment of Halon-1301 as a groundwater age tracer

    Science.gov (United States)

    Beyer, M.; van der Raaij, R.; Morgenstern, U.; Jackson, B.

    2015-06-01

    Groundwater dating is an important tool to assess groundwater resources in regards to their dynamics, i.e. direction and timescale of groundwater flow and recharge, contamination risks and manage remediation. To infer groundwater age information, a combination of different environmental tracers, such as tritium and SF6, are commonly used. However, ambiguous age interpretations are often faced, due to a limited set of available tracers and their individual restricted application ranges. For more robust groundwater dating multiple tracers need to be applied complementarily (or other characterisation methods need to be used to complement tracer information). It is important that additional, groundwater age tracers are found to ensure robust groundwater dating in future. We have recently suggested that Halon-1301, a water soluble and entirely anthropogenic gaseous substance, may be a promising candidate, but its behaviour in water and suitability as a groundwater age tracer had not yet been assessed in detail. In this study, we determined Halon-1301 and inferred age information in 17 New Zealand groundwater samples and various modern (river) water samples. The samples were simultaneously analysed for Halon-1301 and SF6, which allowed for identification of issues such as contamination of the water with modern air during sampling. All analysed groundwater sites had also been previously dated with tritium, CFC-12, CFC-11 and SF6, and exhibited mean residence times ranging from modern (close to 0 years) to over 100 years. The investigated groundwater samples ranged from oxic to highly anoxic. All samples with available CFC data were degraded and/or contaminated in one or both of CFC-11 and CFC-12. This allowed us to make a first attempt of assessing the conservativeness of Halon-1301 in water, in terms of presence of local sources and its sensitivity towards degradation, which could affect the suitability of Halon-1301 as groundwater age tracer. Overall we found Halon-1301

  16. An interesting cause of pulmonary emboli: Acute carbon monoxide poisoning

    Energy Technology Data Exchange (ETDEWEB)

    Sevinc, A.; Savli, H.; Atmaca, H. [Gaziantep University, Gaziantep (Turkey). School of Medicine

    2005-07-01

    Carbon monoxide poisoning, a public health problem of considerable significance, is a relatively frequent event today, resulting in thousands of hospitalizations annually. A 70-year-old lady was seen in the emergency department with a provisional diagnosis of carbon monoxide poisoning. The previous night, she slept in a tightly closed room heated with coal ember. She was found unconscious in the morning with poor ventilation. She had a rare presentation of popliteal vein thrombosis, pulmonary emboli, and possible tissue necrosis with carbon monoxide poisoning. Oxygen treatment with low-molecular-weight heparin (nadroparine) and warfarin therapy resulted in an improvement in both popliteal and pulmonary circulations. In conclusion, the presence of pulmonary emboli should be sought in patients with carbon monoxide poisoning.

  17. US EPA Region 9 carbon monoxide designated areas

    Data.gov (United States)

    U.S. Environmental Protection Agency — Polygon Feature class of Nonattainment Areas for Carbon Monoxide. Nonattainment areas are geographic areas which have not met National Ambient Air Quality Standards...

  18. Carbon monoxide poisoning in the United Arab Emirates.

    Science.gov (United States)

    Al Kaabi, Juma M; Wheatley, Andrew D; Barss, Peter; Al Shamsi, Mariam; Lababidi, Anis; Mushtaq, Ahmed

    2011-01-01

    Carbon monoxide (CO) poisoning is rare in the Arabian Peninsula and occurs almost exclusively during the winter months. Knowledge and perception of the hazards of carbon monoxide is limited. Migrant workers from warm climates appear particularly at risk. We investigated 46 cases of carbon monoxide poisoning presenting at emergency departments from 2007-2009 of the two main hospitals in Al Ain city, United Arab Emirates. Interviews, hospital records, and administered questionnaires were used to collect the data. Among the 46 cases investigated, 24 (52%) were males. Foreign nationals compromised 80% of the cases and the incidence was 3.1 cases per 100,000 residents per year. Burning charcoal in poorly ventilated residences was the predominant source of the carbon monoxide poisoning. Almost all cases (98%) were admitted during the winter months, most in the early morning hours. Carboxyhaemoglobin (COHb) was significantly increased in cases with loss of consciousness and depressed consciousness. There were no reported fatalities.

  19. Same Exposure, Various Clinical Pictures: The Carbon Monoxide Enigma

    Directory of Open Access Journals (Sweden)

    Musa Salmanoglu

    2013-02-01

    Full Text Available -Children and adolescents exposed to the same source of carbon monoxide have been shown to demonstrate different clinical pictures (1,2. The same condition probably may be extrapolated between children with varying ages and hence lung surface areas. Smaller children will receive larger doses of carbon monoxide, because they have greater lung surface area/body weight ratios and increased minute volumes/weight ratios. As carbon monoxide accumulation is expected to be more significant nearer to the ground, another explanation for varying clinical pictures in poisoning events may be the different level of sleeping positions of the casualties. Herein, we report a cluster poisoning of carbon monoxide affecting 5 children from the same family at the same time but in different clinical pictures. [TAF Prev Med Bull 2013; 12(1.000: 118-118

  20. Compartmental modeling and tracer kinetics

    CERN Document Server

    Anderson, David H

    1983-01-01

    This monograph is concerned with mathematical aspects of compartmental an­ alysis. In particular, linear models are closely analyzed since they are fully justifiable as an investigative tool in tracer experiments. The objective of the monograph is to bring the reader up to date on some of the current mathematical prob­ lems of interest in compartmental analysis. This is accomplished by reviewing mathematical developments in the literature, especially over the last 10-15 years, and by presenting some new thoughts and directions for future mathematical research. These notes started as a series of lectures that I gave while visiting with the Division of Applied ~1athematics, Brown University, 1979, and have developed in­ to this collection of articles aimed at the reader with a beginning graduate level background in mathematics. The text can be used as a self-paced reading course. With this in mind, exercises have been appropriately placed throughout the notes. As an aid in reading the material, the e~d of a ...

  1. Application of neutron activation tracer sediment technique on environmental science

    Institute of Scientific and Technical Information of China (English)

    YinYi; ZhongWei-Ni; 等

    1997-01-01

    Field and laboratory inverstigations were carried out to study the transport and dispersion law of polluted sediments near wastewater outlet using neutron activation tracer technique.The direction of transport and dispersion of polluted sediments,dispersion amount in different directions,sedimentary region of polluted sediment and evaluation of polluted risk are given.This provided a new test method for the study of environmental science and added a new forecasted content for the evaluation of environmental influence.

  2. Thermal tracer tomography: from numerical simulation to field implementation

    Science.gov (United States)

    Somogyvári, Márk; Brauchler, Ralf; Bayer, Peter

    2016-04-01

    Choosing heat for subsurface investigations is attractive because changes in temperature can be easily measured, and natural variations are typically slower than the timescale of the experiments. The tomographical setup expands the applicability of such tests to reconstruct the spatial distribution of hydraulic aquifer properties. A new inversion methodology is presented for thermal tracer tomography, using tracer travel times to invert the hydraulic conductivity distribution of the aquifer. If we can assume that heat transport is driven by advection, the travel time of the thermal tracer can be related to the hydraulic parameters of the aquifer. With this assumption other thermal effects such as thermal diffusion or density driven flow appear as noise in the results. To reduce these effects the early time diagnostics of the recorded breakthrough curves are used, focusing on the fastest transport routes between the sources and receivers. The inverse problem of the experiment thus can be formulated as a classical travel time problem, and it can be solved using standard eikonal solver algorithms known from seismic or hydraulic tomography. The method is demonstrated with a high resolution 3-D aquifer analog dataset. The generated 3-D reconstruction reveals the potential of the method, especially in finding the preferential flow paths within the aquifer. Aside from this, the developed method is computationally efficient and can provide results in a fragment of the time required for full-physics model calibration. The method is also tested under field conditions. Four heat tracer injections were performed during a three day field campaign at the Widen field site in northeast Switzerland. Pulse signals were used and the temperature evolution was measured downstream using a distributed measurement system. The preliminary results of the tomographic inversion correspond well with the findings of earlier studies from the field site imaging the same geological features as

  3. Three-Dimensional Bayesian Geostatistical Aquifer Characterization at the Hanford 300 Area using Tracer Test Data

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Xingyuan; Murakami, Haruko; Hahn, Melanie S.; Hammond, Glenn E.; Rockhold, Mark L.; Zachara, John M.; Rubin, Yoram

    2012-06-01

    Tracer testing under natural or forced gradient flow holds the potential to provide useful information for characterizing subsurface properties, through monitoring, modeling and interpretation of the tracer plume migration in an aquifer. Non-reactive tracer experiments were conducted at the Hanford 300 Area, along with constant-rate injection tests and electromagnetic borehole flowmeter (EBF) profiling. A Bayesian data assimilation technique, the method of anchored distributions (MAD) [Rubin et al., 2010], was applied to assimilate the experimental tracer test data with the other types of data and to infer the three-dimensional heterogeneous structure of the hydraulic conductivity in the saturated zone of the Hanford formation. In this study, the Bayesian prior information on the underlying random hydraulic conductivity field was obtained from previous field characterization efforts using the constant-rate injection tests and the EBF data. The posterior distribution of the conductivity field was obtained by further conditioning the field on the temporal moments of tracer breakthrough curves at various observation wells. MAD was implemented with the massively-parallel three-dimensional flow and transport code PFLOTRAN to cope with the highly transient flow boundary conditions at the site and to meet the computational demands of MAD. A synthetic study proved that the proposed method could effectively invert tracer test data to capture the essential spatial heterogeneity of the three-dimensional hydraulic conductivity field. Application of MAD to actual field data shows that the hydrogeological model, when conditioned on the tracer test data, can reproduce the tracer transport behavior better than the field characterized without the tracer test data. This study successfully demonstrates that MAD can sequentially assimilate multi-scale multi-type field data through a consistent Bayesian framework.

  4. Toxicological Investigation of Acute Carbon Monoxide Poisoning in Four Occupants of a Fuming Sport Utility Vehicle

    Directory of Open Access Journals (Sweden)

    Martin Nnoli

    2014-11-01

    Full Text Available Background: This toxicological investigation involves a report on the death of four occupants of a sport utility vehicle on one of the major busy Federal roads of Nigeria where they were held for up to three hours in a traffic jam while the car was steaming. Methods: Autopsy was executed using the standard procedure and toxicological analysis was done using simple spectrophotometric method to establish the level of carboxyhaemoglobin (HbCO in peripheral blood in the four occupants. Results: The autopsy report indicated generalized cyanosis, sub-conjuctival hemorrhages, marked laryngo-trachea edema with severe hyperemia with frothy fluid discharges characteristic of carbon monoxide poisoning. Toxicological report of the level of HbCO in part per million (ppm in the peripheral blood of the four occupants was A= 650 ppm; B= 500 ppm; C= 480 ppm, and D= 495 ppm against the maximum permissible level of 50 ppm. Conclusion: The sudden death of the four occupants was due to excessive inhalation of the carbon monoxide gas from the exhaust fumes leaking into the cabin of the car. The poor road network, numerous potholes, and traffic jam in most of roads in Nigeria could have exacerbated a leaky exhaust of the smoky second hand SUV car leading to the acute carbon monoxide poisoning.

  5. Carbon monoxide exposure in blast furnace workers.

    Science.gov (United States)

    Lewis, S; Mason, C; Srna, J

    1992-09-01

    This study investigated the occupational exposure to carbon monoxide (CO) of a group of blast furnace workers from an integrated steelworks, compared to a control group having no significant occupational CO exposure from other areas in the same works. The study was undertaken in 1984 at Port Kembla, New South Wales. Carboxyhaemoglobin (COHb) levels before and after an eight-hour work shift were measured in 98 male steelworkers: 52 from two CO-exposed iron blast furnaces and 46 controls from production areas in the same steelworks. The sample was stratified by smoking habits. Environmental air CO levels had been found to be consistently higher on one furnace than on the other. Absorption of CO from the working environment occurred in workers on the blast furnace with higher CO levels, regardless of smoking habits. On this blast furnace, some readings of COHb levels after a workshift in nonsmokers approached the proposed Australian occupational limit of 5 per cent COHb saturation. Overall, workers with the highest occupational exposure who smoked most heavily had the highest absorption of CO over a work shift. Biological monitoring gives an accurate measure of individual worker 'dose' of CO from all sources. Both environmental monitoring and biological monitoring need to be included as part of a program for controlling occupational CO exposure.

  6. Carbon Monoxide: An Essential Signalling Molecule

    Science.gov (United States)

    Mann, Brian E.

    Carbon monoxide (CO), like nitric oxide (NO), is an essential signalling molecule in humans. It is active in the cardiovascular system as a vasodilator. In addition, CO possesses anti-inflammatory, anti-apoptotic and anti-proliferative properties and protects tissues from hypoxia and reperfusion injury. Some of its applications in animal models include suppression of organ graft rejection and safeguarding the heart during reperfusion after cardiopulmonary bypass surgery. CO also suppresses arteriosclerotic lesions following angioplasty, reverses established pulmonary hypertension and mitigates the development of post-operative ileus in the murine small intestine and the development of cerebral malaria in mice as well as graft-induced intimal hyperplasia in pigs. There have been several clinical trials using air-CO mixtures for the treatment of lung-, heart-, kidney- and abdominal-related diseases. This review examines the research involving the development of classes of compounds (with particular emphasis on metal carbonyls) that release CO, which could be used in clinically relevant conditions. The review is drawn not only from published papers in the chemical literature but also from the extensive biological literature and patents on CO-releasing molecules (CO-RMs).

  7. Chlorine Monoxide in the Antarctic Spring Stratosphere.

    Science.gov (United States)

    Jaramillo-Ayerbe, Mauricio

    1988-06-01

    A series of observations of stratospheric chlorine monoxide (ClO) were carried out during the austral springs of 1986 and 1987 in McMurdo Station, Antarctica, as part of two experimental campaigns sent to investigate the seasonal decrease in ozone over the antarctic continent (the ozone "hole"). Measurements of the vertical distribution of ClO were obtained by high resolution ground-based emission spectroscopy at 278 GHz, using the Stony Brook mm-wave receiver. They show the presence of an anomalous layer of lower stratospheric ClO which is not observed at other latitudes. This anomalous layer is centered at ~20 km altitude and exhibits a pronounced diurnal variation, reaching a maximum at midday and disappearing at night. During the period of Sep. 20-24, 1987, the lower-stratospheric ClO had a maximum volume mixing ratio of 1.8_sp{+0cdot5}{ -0cdot9} ppbv. A normal ClO layer centered at ~36 km was also observed, with concentrations and diurnal behavior similar to those seen in tropical latitudes. These findings are evidence of anomalous chlorine chemistry taking place in the lower stratosphere during the antarctic spring, and indicate that increasing anthropogenic chlorine is a prime causative agent in the formation of the ozone hole.

  8. Tracer mass recovery in fractured aquifers estimated from multiple well tests.

    Science.gov (United States)

    Sanford, William E; Cook, Peter G; Robinson, Neville I; Weatherill, Douglas

    2006-01-01

    Forced-gradient tracer tests in fractured aquifers often report low mass recoveries. In fractured aquifers, fractures intersected by one borehole may not be intersected by another. As a result (1) injected tracer can follow pathways away from the withdrawal well causing low mass recovery and (2) recovered water can follow pathways not connected to the injection well causing significant tracer dilution. These two effects occur along with other forms of apparent mass loss. If the strength of the connection between wells and the amount of dilution can be predicted ahead of time, tracer tests can be designed to optimize mass recovery and dilution. A technique is developed to use hydraulic tests in fractured aquifers to calculate the conductance (strength of connection) between well pairs and to predict mass recovery and amount of dilution during forced gradient tracer tests. Flow is considered to take place through conduits, which connect the wells to each other and to distant sources or sinks. Mass recovery is related to the proportion of flow leaving the injection well and arriving at the withdrawal well, and dilution is related to the proportion of the flow from the withdrawal well that is derived from the injection well. The technique can be used to choose well pairs for tracer tests, what injection and withdrawal rates to use, and which direction to establish the hydraulic gradient to maximize mass recovery and/or minimize dilution. The method is applied to several tracer tests in fractured aquifers in the Clare Valley, South Australia.

  9. Tracer techniques for urine volume determination and urine collection and sampling back-up system

    Science.gov (United States)

    Ramirez, R. V.

    1971-01-01

    The feasibility, functionality, and overall accuracy of the use of lithium were investigated as a chemical tracer in urine for providing a means of indirect determination of total urine volume by the atomic absorption spectrophotometry method. Experiments were conducted to investigate the parameters of instrumentation, tracer concentration, mixing times, and methods for incorporating the tracer material in the urine collection bag, and to refine and optimize the urine tracer technique to comply with the Skylab scheme and operational parameters of + or - 2% of volume error and + or - 1% accuracy of amount of tracer added to each container. In addition, a back-up method for urine collection and sampling system was developed and evaluated. This back-up method incorporates the tracer technique for volume determination in event of failure of the primary urine collection and preservation system. One chemical preservative was selected and evaluated as a contingency chemical preservative for the storage of urine in event of failure of the urine cooling system.

  10. Application of 41Ca Tracer and Its AMS Measurement in CIAE

    Institute of Scientific and Technical Information of China (English)

    董克君; 何明; 武绍勇; 岳东方; 游曲波; 包轶文; 管永精; 郑元丰; 寅新艺; 王慧娟; 李国强; 杨耀云; 许国基; 胡跃明; 姜山

    2004-01-01

    The man-made calcium isotope 41 Ca is an ideal tracer for the study of calcium metabolism. We represent the first application of accelerator mass spectrometry (AMS) measurement of41 Ca tracer in China. The technique is being applied to the research field of cell messenger at the China Institute of Atomic Energy (CIAE). The sample preparation methods and the AMS measurements are discussed and some interesting results axe presented.

  11. Analysis of tracer and thermal transients during reinjection

    Energy Technology Data Exchange (ETDEWEB)

    Kocabas, I.

    1989-10-01

    This work studied tracer and thermal transients during reinjection in geothermal reserviors and developed a new technique which combines the results from interwell tracer tests and thermal injection-backflow tests to estimate the thermal breakthrough times. Tracer tests are essential to determine the degree of connectivity between the injection wells and the producing wells. To analyze the tracer return profiles quantitatively, we employed three mathematical models namely, the convection-dispersion (CD) model, matrix diffusion (MD) model, and the Avodnin (AD) model, which were developed to study tracer and heat transport in a single vertical fracture. We considered three types of tracer tests namely, interwell tracer tests without recirculation, interwell tracer tests with recirculation, and injection-backflow tracer tests. To estimate the model parameters, we used a nonlinear regression program to match tracer return profiles to the solutions.

  12. In-situ fracture mapping using geotomography and brine tracers

    Energy Technology Data Exchange (ETDEWEB)

    Deadrick, F.J.; Ramirez, A.L.; Lytle, R.J.

    1981-01-01

    The Lawrence Livermore National Laboratory is currently assessing the capabilities of high resolution geophysical methods to characterize geologic sites for the disposal of high level nuclear waste. A successful experiment has recently been performed in which salt water tracers and high frequency electromagnetic waves were utilized to map rock mass fracture zones in-situ. Multiple cross-borehole EM transmissions were used to generate a tomographic image of the fractured rock region between two boreholes. The tomographs obtained correlate well with conventional wireline geophysical logs which can be used to infer the location of fractured zones in the rock mass. This indirect data suggests that the geotomography and brine tracer technique may have merit in mapping fractured zones between boreholes.

  13. A Galaxy-Halo Model for Multiple Cosmological Tracers

    CERN Document Server

    Bull, Philip

    2016-01-01

    The information extracted from large galaxy surveys with the likes of DES, DESI, Euclid, LSST, SKA, and WFIRST will be greatly enhanced if the resultant galaxy catalogues can be cross-correlated with one another. Predicting the nature of the information gain, and developing the tools to realise it, depends on establishing a consistent model of how the galaxies detected by each survey trace the same underlying matter distribution. Existing analytic methods, such as halo occupation distribution (HOD) modelling, are not well-suited for this task, and can suffer from ambiguities and tuning issues when applied to multiple tracers. We construct a simple alternative that provides a common model for the connection between galaxies and dark matter halos across a wide range of wavelengths (and thus tracer populations). This is based on a chain of parametrised statistical distributions that model the connection between (a) halo mass and bulk physical properties of galaxies, such as star-formation rate; and (b) those sam...

  14. Methane emission quantification from landfills using a double tracer approach

    DEFF Research Database (Denmark)

    Scheutz, Charlotte; Samuelsson, J.; Fredenslund, Anders Michael

    2007-01-01

    in the October respectively February measurement. The CH4 emission from the compost area was 0.5 kg CH4 h-1, whereas the carbon dioxide (CO2) flux and nitrous oxide (N2O) was quantified to be in the order of 332 kg CO2 h-1 and 0.06 kg N2O h-1 respectively. The sludge pit located west of the compost material......A tracer method was successfully used for quantification of the whole methane (CH4) emission from Fakse landfill. By using two different tracers the emission from different sections of the landfill could be quantified. Furthermore, is was possible to determine the emissions from local on site...... sources; a composting facility and a sewage sludge storage unit by scaling the tracer method down. Two field campaigns were performed; during October 11-12, 2006 and February 19-20, 2007. At both field campaigns an overall leak search showed that the CH4 emission from the old landfill section...

  15. Comparison of different tracer methods in detecting sentinel lymph nodes in gastric cancer%不同示踪法在胃癌前哨淋巴结检测中的应用比较

    Institute of Scientific and Technical Information of China (English)

    程黎阳; 谢正勇; 戴观荣; 赵为国; 王弘; 周宏峰

    2010-01-01

    Objective To explore the optimum sentinel lymph node (SLN) mapping method in gastric cancer. Methods The clinical data of 59 patients who were confirmed with gastric cancer at Guangzhou General Hospital of Guangzhou Military Command from January 2004 to August 2008 were retrospectively analysed. Patent blue V dye was used in 20 patients (group A), technetium-99m sulfur colloid was used in 20 patients (group B),and a combination of patent blue V dye and technetium-99m sulfur colloid were used in 19 patients (group C).The number of SLNs detected, and accuracy and false-negative rate of SLNs in diagnosing regional lymph node metastasis were analysed by t test and chi-square test. Results The numbers of SLNs detected in groups A, B and C were 38 (1.9 per case), 31 (1.6 per case) and 56 (2.9 per case), respectively. In group C, 46 SLNs were screened out by patent blue V dye and technetium-99m sulfur colloid simultaneously, six SLNs were only detected by patent blue V dye and four only by technetium-99m sulfur colloid. There was a significant difference in the number of SLNs detected among the three groups (t = 4.35, P < 0. 05 ). The number of SLNs detected in group C was significantly greater than that in groups A and B (t = 4. 21, 3. 54, P < 0.05 ). The accuracy and false-negative rate of SLNs in diagnosing regional lymph node metastasis were 95% (19/20) and 5% (1/20) in group A, 90% (18/20) and 10% (2/20) in group B, and 100% (19/19) and 0 in group C. The accuracy was significantly higher (x2 = 163.01, P < 0.05) and the false-negative rate was significantly lower in group C compared with those in groups A and B (x2 = 170. 14, P < 0. 05). Conclusion A combination of dye and radioactive tracer is a favorable method for detecting SLNs in gastric cancer.%目的 探讨理想的胃癌前哨淋巴结(SLN)检测方法.方法 前瞻性分析2004年1月至2008年8月广州军区广州总医院确诊的59例胃癌患者的临床资料,按随机数字表

  16. CHANGE OF CARBON MONOXIDE IN PLASMA AND TISSUE DURING ACUTE HYPOXIA

    Institute of Scientific and Technical Information of China (English)

    丁学琴; 刘贵明; 王俊科; 盛卓人

    2003-01-01

    Objective.To investigate the role of endogenous carbon monoxide(CO)in hypoxia. Methods. After rats were inhaled with hypoxic gases and the heme oxygenase inhibitor ZnPPIX was administered,we measured the CO levels in plasma,liver,lung and kidney. Meanwhile plasma cGMP levels were observed. Furthermore,we recorded the changes of hemodynamic and blood gases. Results. Acute mild hypoxia(10%O2)significantly increased CO levels in plasma as well as liver,kidney and lung,while acute severe hypoxia(5%O2)significantly decreased CO levels in plasma as well as liver,kidney and lung. In addition,the former significantly elevated cGMP levels in plasma while the latter markedly reduced cGMP levels in plasma. The hemodynamic changes occurred in accordance with the changes of carbon monoxide. Conclusions. Our results indicate,for the first time ,that the endogenous carbon monoxide plays an important role in regulating the vessel tone during hypoxia.

  17. Changes in the Autonomic Nervous System in Patients with Carbon Monoxide Poisoning

    Directory of Open Access Journals (Sweden)

    A. V. Badalyan

    2009-01-01

    Full Text Available Objective: to examine changes in the autonomic nervous system (ANS function in patients with carbon monoxide poisoning in relation to the condition severity. Subjects and methods. The ANS was studied in 114 patients aged 15 to 82 years with carbon monohydrate poisoning who were treated at the N. V. Sklifosovsky Research Institute of Emergency Care, Moscow, in 2004—2008. Cardiointervalographic readings were analyzed in relation to the condition severity, the presence of thermal damages to the skin and upper airway, and that of blood alcohol. Results. Within the first hours after poisoning, the function of the ANS was found to be impaired, which was associated with the development of hypersympathicotonia caused by the increased activity of its sympathetic part and the decreased tone of the parasympathetic one. The magnitude of hypersympathicotonia depends on the severity of poisoning, on the presence of thermal damages to the upper respiratory tract and that of blood alcohol. The preponderance of the tone of the ANS parasympathetic part suggests the disturbance of adaptive and compensatory mechanisms and the likely poor prognosis of the poisoning. Conclusion. Cardiointervalography is recommended for the objective evaluation of the severity of carbon monoxide poisoning. Key words: carbon monoxide, autonomic nervous system, cardiointervalog-raphy, adaptive and compensatory mechanisms.

  18. Accidental carbon monoxide poisoning presenting without a history of exposure: A case report

    Directory of Open Access Journals (Sweden)

    Bennetto Luke

    2008-04-01

    Full Text Available Abstract Introduction Carbon monoxide poisoning is easy to diagnose when there is a history of exposure. When the exposure history is absent, or delayed, the diagnosis is more difficult and relies on recognising the importance of multi-system disease. We present a case of accidental carbon monoxide poisoning. Case presentation A middle-aged man, who lived alone in his mobile home was found by friends in a confused, incontinent state. Initial signs included respiratory failure, cardiac ischaemia, hypotension, encephalopathy and a rash, whilst subsequent features included rhabdomyolysis, renal failure, amnesia, dysarthria, parkinsonism, peripheral neuropathy, supranuclear gaze palsy and cerebral haemorrhage. Despite numerous investigations including magnetic resonance cerebral imaging, lumbar puncture, skin biopsy, muscle biopsy and electroencephalogram a diagnosis remained elusive. Several weeks after admission, diagnostic breakthrough was achieved when the gradual resolution of the patient's amnesia, encephalopathy and dysarthria allowed an accurate history to be taken for the first time. The patient's last recollection was turning on his gas heating for the first time since the spring. A gas heating engineer found the patient's gas boiler to be in a dangerous state of disrepair and it was immediately decommissioned. Conclusion This case highlights several important issues: the bewildering myriad of clinical features of carbon monoxide poisoning, the importance of making the diagnosis even at a late stage and preventing the patient's return to a potentially fatal toxic environment, and the paramount importance of the history in the diagnostic method.

  19. Journal: A Review of Some Tracer-Test Design Equations for Tracer-Mass Estimation and Sample Collection Frequency

    Science.gov (United States)

    Determination of necessary tracer mass, initial sample-collection time, and subsequent sample-collection frequency are the three most difficult aspects to estimate for a proposed tracer test prior to conducting the tracer test. To facilitate tracer-mass estimation, 33 mass-estima...

  20. Journal: A Review of Some Tracer-Test Design Equations for Tracer-Mass Estimation and Sample Collection Frequency

    Science.gov (United States)

    Determination of necessary tracer mass, initial sample-collection time, and subsequent sample-collection frequency are the three most difficult aspects to estimate for a proposed tracer test prior to conducting the tracer test. To facilitate tracer-mass estimation, 33 mass-estima...

  1. Tracer-based prediction of thermal reservoir lifetime: scope, limitations, and the role of thermosensitive tracers

    Science.gov (United States)

    Ghergut, I.; Behrens, H.; Karmakar, S.; Licha, T.; Nottebohm, M.; Sauter, M.

    2012-04-01

    Thermal-lifetime prediction is a traditional endeavour of inter-well tracer tests conducted in geothermal reservoirs. Early tracer test signals (detectable within the first few years of operation) are expected to correlate with late-time production temperature evolutions ('thermal breakthrough', supposed to not occur before some decades of operation) of a geothermal reservoir. Whenever a geothermal reservoir can be described as a single-fracture system, its thermal lifetime will, ideally, be determined by two parameters (say, fracture aperture and porosity), whose inversion from conservative-tracer test signals is straightforward and non-ambiguous (provided that the tracer tests, and their interpretation, are performed in accordance to the rules of the art). However, as soon as only 'few more' fractures are considered, this clear-cut correlation is broken. A given geothermal reservoir can simultaneously feature a single-fracture behaviour, in terms of heat transport, and a multiple-fracture behaviour, in terms of solute tracer transport (or vice-versa), whose effective values of fracture apertures, spacings, and porosities are essentially uncorrelated between heat and solute tracers. Solute transport parameters derived from conservative-tracer tests will no longer characterize the heat transport processes (and thus temperature evolutions) taking place in the same reservoir. Parameters determining its thermal lifetime will remain 'invisible' to conservative tracers in inter-well tests. We demonstrate this issue at the example of a five-fracture system, representing a deep-geothermal reservoir, with well-doublet placement inducing fluid flow 'obliquely' to the fractures. Thermal breakthrough in this system is found to strongly depend on fracture apertures, whereas conservative-solute tracer signals from inter-well tests in the same system do not show a clear-cut correlation with fracture apertures. Only by using thermosensitive substances as tracers, a reliable

  2. Characterization of fractured reservoirs using tracer and flow-rate data

    Science.gov (United States)

    Juliusson, Egill; Horne, Roland N.

    2013-05-01

    This article introduces a robust method for characterizing fractured reservoirs using tracer and flow-rate data. The flow-rate data are used to infer the interwell connectivity matrix, which describes how injected fluids are divided between producers in the reservoir. The tracer data are used to find a function called the tracer kernel for each injector-producer connection. The tracer kernel describes the volume and dispersive properties of the interwell flow path. A combination of parametric and nonparametric regression methods was developed to estimate the tracer kernels in situations where data are collected at variable flow rate or variable-injected concentration conditions. This characterization method was developed to describe enhanced geothermal systems, although it works well in general for characterizing incompressible flow in fractured reservoirs (e.g., geothermal, carbon sequestration, radioactive waste and waterfloods of oil fields) where transverse dispersivity can be considered negligible and production takes place at constant bottomhole pressure conditions. The inferred metrics can be used to sketch informative field maps and predict tracer breakthrough curves at variable flow-rate conditions.

  3. Graphical Analysis of PET Data Applied to Reversible and Irreversible Tracers

    Energy Technology Data Exchange (ETDEWEB)

    Logan, Jean

    1999-11-18

    Graphical analysis refers to the transformation of multiple time measurements of plasma and tissue uptake data into a linear plot, the slope of which is related to the number of available tracer binding sites. This type of analysis allows easy comparisons among experiments. No particular model structure is assumed, however it is assumed that the tracer is given by bolus injection and that both tissue uptake and the plasma concentration of unchanged tracer are monitored following tracer injection. The requirement of plasma measurements can be eliminated in some cases when a reference region is available. There are two categories of graphical methods which apply to two general types of ligands--those which bind reversibly during the scanning procedure and those which are irreversible or trapped during the time of the scanning procedure.

  4. Testing and comparison of four ionic tracers to measure stream flow loss by multiple tracer injection

    Science.gov (United States)

    Zellweger, G.W.

    1994-01-01

    An injectate containing lithium, sodium, chloride and bromide was added continuously at five sites along a 507 m study reach of St Kevin Gulch, Lake County, Colorado to determine which sections of the stream were losing water to the stream bed and to ascertain how well the four tracers performed. The acidity of the stream (pH 3.6) made it possible for lithium and sodium, which are normally absorbed by ion exchange with stream bed sediment, to be used as conservative tracers. Net flow losses as low as 0.81 s-1, or 8% of flow, were calculated between measuring sites. By comparing the results of simultaneous injection it was determined whether subsections of the study reach were influent or effluent. Evaluation of tracer concentrations along 116 m of stream indicated that all four tracers behaved conservatively. Discharges measured by Parshall flumes were 4-18% greater than discharges measured by tracer dilution. -from Author

  5. High temperature thermodynamics and vaporization of stoichiometric titanium monoxide

    Energy Technology Data Exchange (ETDEWEB)

    Sheldon, R.I.; Gilles, P.W.

    1976-08-17

    Three vaporization experiments were performed on samples of nearly stoichiometric titanium monoxide. Two experiments were constant temperature experiments (1806/sup 0/K) designed to measure the equilibrium vapor pressures of Ti(g) and TiO(g). In one experiment titanium monoxide was vaporized from a tungsten Knudsen effusion cell; the vapor was collected on a water cooled quartz cap surrounding the cell; and the total amount of titanium deposited on the cap was analyzed colorimetrically. In the second constant temperature experiment (1806/sup 0/K) the vapor composition in equilibrium with nearly stoichiometric titanium monoxide was measured mass spectrometrically. The mass spectrometer results were used to apportion the total titanium collected in the first experiment to Ti(g) and TiO(g). In the third experiment the temperature dependence of the ions Ti/sup +/(48) and TiO(64) was measured spectrometrically. The results obtained in this work are compared with published thermodynamic properties of the titanium oxygen system, and indicate the standard free energy of formation of titanium monoxide obtained from the earliest calorimetric measurements yielded a result not negative enough and also oxygen pressures obtained by emf measurements for stoichiometric titanium monoxide at 1806/sup 0/K are high by a factor of 42.6. The present results are in good agreement with the thermodynamic properties reported in recently issued pages of the JANAF Thermochemical Tables.

  6. Radioisotope tracer study in a sludge hygienization research irradiator (SHRI).

    Science.gov (United States)

    Pant, H J; Thýn, J; Zitný, R; Bhatt, B C

    2001-01-01

    A radioisotope tracer study has been carried out in a batch type sludge hygienization research irradiator with flow from top to bottom, the objective being to measure flow rate, circulation and mixing times and to investigate the hydrodynamic behaviour of the irradiator for identifying the cause(s) of malfunction. A stimulus-response technique with NH4(82)Br as a tracer was used to measure the above parameters. Experiments were carried out at three different flow rates, i.e 1.0, 0.64 and 0.33 m3/min. Three combined models based on a set of differential equations are proposed and used to simulate the measured tracer concentration curves. The obtained parameters were used to estimate dead volume and analyse hydrodynamic behaviour of the irradiator. The nonlinear regression problem of model parameter estimation was solved using the Marquardt-Levenberg method. The measured flow rate was found to be in good agreement with the values shown by the flow meter. The circulation times were found to be half of the mixing times. A simple approach for estimation of dose based on a known vertical dose-rate profile inside the irradiator is presented. About one-fourth of the volume of the irradiator was found to be dead at lower flow rates and this decreased with increase in flow rate. At higher flow rates, a semi stagnant volume was found with slow exchange of flow between the active and dead volumes.

  7. Radioisotope tracer study in a sludge hygienization research irradiator (SHRI)

    Energy Technology Data Exchange (ETDEWEB)

    Pant, H.J. E-mail: hjpant@aspsara.barc.ernet.in; Thyn, J.; Zitny, R.; Bhatt, B.C

    2001-01-15

    A radioisotope tracer study has been carried out in a batch type sludge hygienization research irradiator with flow from top to bottom, the objective being to measure flow rate, circulation and mixing times and to investigate the hydrodynamic behaviour of the irradiator for identifying the cause(s) of malfunction. A stimulus-response technique with NH{sup 82}{sub 4}Br as a tracer was used to measure the above parameters. Experiments were carried out at three different flow rates, i.e 1.0, 0.64 and 0.33 m{sup 3}/min. Three combined models based on a set of differential equations are proposed and used to simulate the measured tracer concentration curves. The obtained parameters were used to estimate dead volume and analyse hydrodynamic behaviour of the irradiator. The nonlinear regression problem of model parameter estimation was solved using the Marquardt-Levenberg method. The measured flow rate was found to be in good agreement with the values shown by the flow meter. The circulation times were found to be half of the mixing times. A simple approach for estimation of dose based on a known vertical dose-rate profile inside the irradiator is presented. About one-fourth of the volume of the irradiator was found to be dead at lower flow rates and this decreased with increase in flow rate. At higher flow rates, a semi stagnant volume was found with slow exchange of flow between the active and dead volumes.

  8. A galaxy-halo model for multiple cosmological tracers

    Science.gov (United States)

    Bull, Philip

    2017-10-01

    The information extracted from large galaxy surveys with the likes of DES, DESI, Euclid, LSST, SKA, and WFIRST will be greatly enhanced if the resultant galaxy catalogues can be cross-correlated with one another. Predicting the nature of the information gain, and developing the tools to realize it, depends on establishing a consistent model of how the galaxies detected by each survey trace the same underlying matter distribution. Existing analytic methods, such as halo occupation distribution modelling, are not well suited for this task, and can suffer from ambiguities and tuning issues when applied to multiple tracers. In this paper, we take the first step towards constructing an alternative that provides a common model for the connection between galaxies and dark matter haloes across a wide range of wavelengths (and thus tracer populations). This is based on a chain of parametrized statistical distributions that model the connection between (i) halo mass and bulk physical properties of galaxies, such as star formation rate; and (ii) those same physical properties and a variety of emission processes. The result is a flexible parametric model that allows analytic halo model calculations of one-point functions to be carried out for multiple tracers, as well as providing semi realistic galaxy properties for fast mock catalogue generation.

  9. An investigation of radial tracer flow in naturally fractured reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Jetzabeth, Ramirez-Sabag; Fernando, Samaniego V.; Jesus, Rivera R.; Fernando Rodriguez

    1991-01-01

    This study presents a general solution for the radial flow of tracers in naturally fractured reservoirs. Continuous and finite step injection of chemical and radioactive tracers are considered. The reservoir is treated as being composed of two regions: a mobile region where longitudinal dispersion and convection take place and a stagnant region where only diffusion and adsorption are allowed. Radioactive decay is considered in both regions. The model of this study is thoroughly compared to those previously presented in literature by Moench and Ogata, Tang et al., Chen et al., and Hsieh et al. The solution is numerically inverted by means of the Crump algorithm. A detailed validation of the model with respect to solutions previously presented and/or simplified physical conditions solutions (i.e., homogeneous case) or limit solutions (i.e., for short times) was carried out. The influence of various dimensionless parameters that enter into the solution was investigated. A discussion of results obtained through the Crump and Stehfest algorithm is presented, concluding that the Crump method provides more reliable tracer concentrations.

  10. Application of transition metal isotope tracers in global change research

    Institute of Scientific and Technical Information of China (English)

    SONG Jinming; Thomas F. Pedersen

    2005-01-01

    High-precision isotope composition determinations using multicollector, magnetic-sector inductively coupled plasma mass spectrometry (MC-ICPMS) have recently revealed that some transition metal isotopes such as those of Mo, Fe, Cu, Zn etc. can be used as biogeochemical tracers in global change research.The Mo isotope system may be useful in paleoredox investigations indicating that δ 97/95Mo in seawater may co-vary with changes in the relative proportions of anoxic and oxic sedimentation in the ocean, and that this variation may be recorded in δ 97/95Mo of anoxic sediments. The Mo continental flux into the oceans and the global Mo isotope budget can be estimated fromδ 97/95MO values. The Fe isotope composition in seawater is an important issue because Fe plays a controlling role in biological productivity in the oceans and its abundance in seawater may have substantial effect on climate changes. Iron isotope fractionations could result from bio- and abio-processes and have about 0.1% variation (δ 56/54Fe), so Fe isotopes considered alone cannot be used to distinguish the products of abiotic and biotic Fe processing in geological records. Cu and Zn isotopes are also used as biogeochemical tracers, but the researches are relatively less. This review mainly focuses on the methods for preparation, purification and determination of new isotope tracer samples, and on isotope applications in marine environmental changes.

  11. Comparative evaluation of two sediment tracers in a rainfall simulation experiment

    Science.gov (United States)

    Strauss, Peter; Guzman, Gema; Mentler, Axel

    2015-04-01

    The use of sediment tracers tries to contribute to solving problems of traditional soil erosion measurements such as allocation of erosional and depositional areas. A number of different tracing approaches have already been established however, as none of available techniques are able to fully satisfy all the requirements for being an ideal tracer the search for alternative methods continues. Clays tagged with quaternary ammonium compounds are widely used in industry and are easy to incorporate into soils for sediment tracing experiments. To explore the potential of these clays a laboratory experiment was carried out in order to characterize their behaviour as compared to the well-established sediment tracer magnetic iron oxide. The experiment consisted of a simulated rainfall event of 60 mm/h in a box laboratory flume divided in two ridge-furrow subplots (200 x 57 cm). In order to evaluate transport and redistribution of soil from the ridges to the furrow and to measure the dynamic behaviour of the tracers during the rainfall a dense grid of soil samples was taken before and after the experiment (140 samples in total). Runoff and sediment were collected and all samples were analysed for both tracers. Results indicate the general suitability of organophilic clays to monitor soil redistribution by water erosion. The average relative contributions from shoulders and furrow to total sediment export determined by both tracers were similar and indicated a higher contribution from ridges. A key advantage of using organophilic clays is that the detection limit of organophilic clays is extremely low and the background concentration is zero. Despite the inherent differences between both tracers such as way of bounding, sediment enrichment or analytical technique, this experimental comparison of an established and more novel tracer method underscores the potential suitability of the latter for soil erosion studies.

  12. Carbon monoxide in clouds at low metallicity in the dwarf irregular galaxy WLM.

    Science.gov (United States)

    Elmegreen, Bruce G; Rubio, Monica; Hunter, Deidre A; Verdugo, Celia; Brinks, Elias; Schruba, Andreas

    2013-03-28

    Carbon monoxide (CO) is the primary tracer for interstellar clouds where stars form, but it has never been detected in galaxies in which the oxygen abundance relative to hydrogen is less than 20 per cent of that of the Sun, even though such 'low-metallicity' galaxies often form stars. This raises the question of whether stars can form in dense gas without molecules, cooling to the required near-zero temperatures by atomic transitions and dust radiation rather than by molecular line emission; and it highlights uncertainties about star formation in the early Universe, when the metallicity was generally low. Here we report the detection of CO in two regions of a local dwarf irregular galaxy, WLM, where the metallicity is 13 per cent of the solar value. We use new submillimetre observations and archival far-infrared observations to estimate the cloud masses, which are both slightly greater than 100,000 solar masses. The clouds have produced stars at a rate per molecule equal to 10 per cent of that in the local Orion nebula cloud. The CO fraction of the molecular gas is also low, about 3 per cent of the Milky Way value. These results suggest that in small galaxies both star-forming cores and CO molecules become increasingly rare in molecular hydrogen clouds as the metallicity decreases.

  13. Copper Ion as a New Leakage Tracer

    Directory of Open Access Journals (Sweden)

    Modaresi J.

    2013-12-01

    Full Text Available Statement of Problem: Most failures of root canal treatments are caused by bacteria. Studies showed that the most common cause of endodontic failures were the incomplete obturation of the root canal and the lack of adequate apical seal. Some in-vitro methods are used to estimate sealing quality, generally by measuring microleakage that allows the tracer agent to penetrate the filled canal.Purpose: Conventional methods of evaluating the seal of endodontically treated teeth are complicated and have some drawbacks. We used copper ion diffusion method to assess the leakage and the results were compared to dye penetration method.Materials and Method: The crowns of 21 extracted teeth were cut off at the CEJ level. After preparing the canals, the teeth were placed in tubes containing saline. They were divided randomly into 15 experimental cases; 3 positive and 3 negative controls. Positive controls were filled by single cone without sealer while the experimental and the negative control groups were filled by lateral technique. The coronal portion of gutta was removed and 9mm was left. The external surface of each tooth was coated with nail polish. Two millimeters of apical portion was immersed into 9ml of distilled water and 0.3ml of CuSO4 solution was injected into the coronal portion. After 2 days, copper sulfate was measured by an atomic absorption spectrophotometer. The teeth were then immersed in 2% methylene blue for 24 hours, sectioned and the extent of dye penetration was measured by a stereomicroscope.Results: The maximum and minimum recorded copper ion concentrations for the experimental group were 18.37 and 2.87ppm respectively. The maximum and minimum recorded dye penetrations for the experimental group were 8.5 and 3.5mm respectively. The statistical analysis, adopting paired samples test, showed poor correlation between average recorded results of two methods.Conclusion: Based on our results, there was no significant correlation between

  14. Forensic aspects of carbon monoxide poisoning by charcoal burning in Denmark, 2008-2012

    DEFF Research Database (Denmark)

    Nielsen, Pia Rude; Gheorghe, Alexandra; Lynnerup, Niels

    2014-01-01

    Carbon monoxide (CO) inhalation is a well-known method of committing suicide. There has been a drastic increase in suicide by inhalation of CO, produced from burning charcoal, in some parts of Asia, and a few studies have reported an increased number of these deaths in Europe. CO-related deaths...... found in 9 cases. Data suggest that this method of death has increased significantly in Denmark. Therefore, it is highly relevant to draw attention to the subject, to increase awareness as well as prevent future escalation....

  15. Transformationally decoupling clustering and tracer bias

    CERN Document Server

    Neyrinck, Mark C

    2014-01-01

    Gaussianizing transformations are used statistically in many non-cosmological fields, but in cosmology, we are only starting to apply them. Here I explain a strategy of analyzing the 1-point function (PDF) of a spatial field, together with the 'essential' clustering statistics of the Gaussianized field, which are invariant to a local transformation. In cosmology, if the tracer sampling is sufficient, this achieves two important goals. First, it can greatly multiply the Fisher information, which is negligible on nonlinear scales in the usual $\\delta$ statistics. Second, it decouples clustering statistics from a local bias description for tracers such as galaxies.

  16. Geologic flow characterization using tracer techniques

    Energy Technology Data Exchange (ETDEWEB)

    Klett, R. D.; Tyner, C. E.; Hertel, Jr., E. S.

    1981-04-01

    A new tracer flow-test system has been developed for in situ characterization of geologic formations. This report describes two sets of test equipment: one portable and one for testing in deep formations. Equations are derived for in situ detector calibration, raw data reduction, and flow logging. Data analysis techniques are presented for computing porosity and permeability in unconfined isotropic media, and porosity, permeability and fracture characteristics in media with confined or unconfined two-dimensional flow. The effects of tracer pulse spreading due to divergence, dispersion, and porous formations are also included.

  17. [Massive poisoning with carbon monoxide: an update from a case].

    Science.gov (United States)

    Díaz, Mariano; Crapanzano, Gabriel; Cabrerizo, Silvia; Aichele, Cristina; Deurtiaga, Alejandra; Vallejos, Yamila

    2017-02-01

    Carbon monoxide is known as the "silent murderer" because it is a colorless and odorless gas. According to these characteristics, toxicity goes unnoticed which makes the diagnosis difficult. In most cases, the cold periods and group poisoning make suspect its presence because inappropriate heat both in home or public environments. Our goal is to inform about a mass carbon monoxide poisoning in a children's parties room using a combustion source installed, not for the purpose of heating, but as a supply of light (generator), emphasizing that it can occur in any time of the year.

  18. Structural and magnetic properties of mechanochemically synthesized nanocrystalline titanium monoxide

    Directory of Open Access Journals (Sweden)

    Barudžija Tanja

    2012-01-01

    Full Text Available Nano-sized titanium monoxide (TiO powder was prepared by mechanochemical synthesis. A mixture of commercial Ti and TiO2 (rutile powders with the molar ratio of 1:1 was milled in a planetary ball mill for 5, 10, 20, 30 and 60 min under argon atmosphere. The final single-phase titanium monoxide sample was characterized by X-ray diffraction (XRD, magnetic measurements using a superconducting quantum interference device magnetometer (SQUID and thermogravimetric analysis (TGA. The temperature dependency of the magnetic susceptibility is characterized by significant contribution of Pauli paramagnetism due to conduction electrons.

  19. Assessment of the sulfur hexafluoride (SF6) tracer technique for measuring enteric methane emissions from cattle.

    Science.gov (United States)

    McGinn, S M; Beauchemin, K A; Iwaasa, A D; McAllister, T A

    2006-01-01

    A commonly used method of measuring enteric methane (CH4) emissions from ruminants is the SF6 tracer technique that measures respired and eructated CH4. However, within the animal, a small proportion of CH4 is produced post-ruminally and some of this may escape through the rectum. The comparison of emissions using a chamber technique that measures all enteric CH4 losses, and the SF6 tracer technique, could give some insight into the magnitude of post-ruminal emission. The objective of our study was to assess the precision and accuracy of the SF6 tracer technique against a chamber technique for cattle fed a range of diets. Using a repeated-measures design, eight beef heifers were offered a high grain or high forage diet for ad libitum or restricted (65% of ad libitum) feed intake to vary the site of digestion within the gastrointestinal tract (n = 24). The SF6 tracer technique underestimated CH4 emissions on average by 4% relative to the chamber technique. This difference was not significant (P > 0.05) and suggests low post-ruminal CH4 emissions. There was a trend for greater accuracy and precision of the SF6 tracer technique when used with cattle fed a high forage diet at a restricted level of intake. The high forage diet corresponds to the conditions of cattle grazing pasture, suggesting the SF6 tracer technique is most reliable for the grazing system.

  20. Impact of meteorological inflow uncertainty on tracer transport and source estimation in urban atmospheres

    Science.gov (United States)

    Lucas, Donald D.; Gowardhan, Akshay; Cameron-Smith, Philip; Baskett, Ronald L.

    2016-10-01

    A computational Bayesian inverse technique is used to quantify the effects of meteorological inflow uncertainty on tracer transport and source estimation in a complex urban environment. We estimate a probability distribution of meteorological inflow by comparing wind observations to Monte Carlo simulations from the Aeolus model. Aeolus is a computational fluid dynamics model that simulates atmospheric and tracer flow around buildings and structures at meter-scale resolution. Uncertainty in the inflow is propagated through forward and backward Lagrangian dispersion calculations to determine the impact on tracer transport and the ability to estimate the release location of an unknown source. Our uncertainty methods are compared against measurements from an intensive observation period during the Joint Urban 2003 tracer release experiment conducted in Oklahoma City. The best estimate of the inflow at 50 m above ground for the selected period has a wind speed and direction of 4.6-2.5+2.0 m s-1 and 158.0-23+16 , where the uncertainty is a 95% confidence range. The wind speed values prescribed in previous studies differ from our best estimate by two or more standard deviations. Inflow probabilities are also used to weight backward dispersion plumes and produce a spatial map of likely tracer release locations. For the Oklahoma City case, this map pinpoints the location of the known release to within 20 m. By evaluating the dispersion patterns associated with other likely release locations, we further show that inflow uncertainty can explain the differences between simulated and measured tracer concentrations.

  1. Oral treatment of rodents with insecticides for control of sand flies (Diptera: Psychodidae) and the fluorescent tracer technique (FTT) as a tool to evaluate potential sand fly control methods.

    Science.gov (United States)

    Mascari, T M; Clark, J; Gordon, S; Mitchell, M A; Rowton, E D; Stout, R; Foil, L D

    2011-03-01

    In laboratory studies, insecticides (diflubenzuron, novaluron, methoprene and, pyriproxyfen) that have been incorporated into rodent diets were effective as feed-throughs against sand fly larvae. Novaluron also was effective against sand fly larvae at low concentrations and under simulated field conditions. Ivermectin has been shown to be effective as a systemic insecticide, killing 100% of blood-feeding sand flies for up to seven d after rodents were treated. The fluorescent tracer technique (FTT) is the use of certain fluorescent dyes (rhodamine B or uranine O) as feed-through transtadial biomarkers for phlebotomine sand flies, systemic biomarkers for blood-feeding sand flies, and permanent markers for nectar-feeding sand flies. The results of these laboratory studies provide proof of concept for the FTT and indicate that the FTT could be used to delineate specific foci with rodent/sand fly associations that would be susceptible to control by using feed-through or systemic insecticides, or foci where insecticide-treated sugar baits could be used against sand flies.

  2. Estimates of tracer-based piston-flow ages of groundwater from selected sites-National Water-Quality Assessment Program, 1992-2005

    Science.gov (United States)

    Hinkle, Stephen R.; Shapiro, Stephanie D.; Plummer, L. Niel; Busenberg, Eurybiades; Widman, Peggy K.; Casile, Gerolamo C.; Wayland, Julian E.

    2011-01-01

    This report documents selected age data interpreted from measured concentrations of environmental tracers in groundwater from 1,399 National Water-Quality Assessment (NAWQA) Program groundwater sites across the United States. The tracers of interest were chlorofluorocarbons (CFCs), sulfur hexafluoride (SF6), and tritium/helium-3 (3H/3He). Tracer data compiled for this analysis primarily were from wells representing two types of NAWQA groundwater studies - Land-Use Studies (shallow wells, usually monitoring wells, in recharge areas under dominant land-use settings) and Major-Aquifer Studies (wells, usually domestic supply wells, in principal aquifers and representing the shallow, used resource). Reference wells (wells representing groundwater minimally impacted by anthropogenic activities) associated with Land-Use Studies also were included. Tracer samples were collected between 1992 and 2005, although two networks sampled from 2006 to 2007 were included because of network-specific needs. Tracer data from other NAWQA Program components (Flow System Studies, which are assessments of processes and trends along groundwater flow paths, and various topical studies) were not compiled herein. Tracer data from NAWQA Land-Use Studies and Major-Aquifer Studies that previously had been interpreted and published are compiled herein (as piston-flow ages), but have not been reinterpreted. Tracer data that previously had not been interpreted and published are evaluated using documented methods and compiled with aqueous concentrations, equivalent atmospheric concentrations (for CFCs and SF6), estimates of tracer-based piston-flow ages, and selected ancillary data, such as redox indicators, well construction, and major dissolved gases (N2, O2, Ar, CH4, and CO2). Tracer-based piston-flow ages documented in this report are simplistic representations of the tracer data. Tracer-based piston-flow ages are a convenient means of conceptualizing groundwater age. However, the piston

  3. The Effects of Low Level Prenatal Carbon Monoxide on Neocortical Development

    Science.gov (United States)

    2010-06-02

    378.1958). Ginsberg MD, Myers RE (Fetal brain damage following maternal carbon monoxide intoxication: an experimental study. Acta obstetricia et...monoxide production and blood loss at delivery. Acta obstetricia et gynecologica Scandinavica 48:362-370.1969). Longo LD (Carbon monoxide in the

  4. The Application of Tracer Method for SLN Localization and Testing with Methylene Blue Breast Glands Axillary Tail Injection in the Treatment of Early Breast Cancer%美蓝腋尾部注射示踪哨兵淋巴结定位及检测在早期乳腺癌治疗中的应用

    Institute of Scientific and Technical Information of China (English)

    王帅; 尚春力; 孙宝杰

    2015-01-01

    目的:研究乳腺腺体腋尾部注射美蓝示踪哨兵淋巴结法及哨兵淋巴结活检(SLNB)的临床应用。方法应用美蓝腋尾部注射法对44例乳腺癌患者行SLNB,随后行乳腺癌改良根治术。结果哨兵淋巴结SLN的检出率为93.2%,准确性为88.2%,敏感性为93.8%,假阴性率为11.8%,SLNB与ALND阳性率比较无统计学差异。结论美蓝腋尾部注射示踪哨兵淋巴结技术可应用于临床,SLNB活检可用于预测腋窝淋巴结转移情况。%Objective The purpose of this paper is to study the clinical application of tracer method for SLN with methylene blue breast glands axillary tail injection and the sentinel lymph node biopsy (SLNB). Methods The method described in this paper is to apply methylene blue breast glands axillary tail injection to 44 breast cancer cases and perform modiifed radical mastectomy successively. Results The result shows that the detection rate of SLN was 93.2%, accuracy was of 88.2%, sensitivity was of 93.8%, and false-negative rate was of 11.8%. There was no statistical difference of positive rate between SLNB and axillary lymph node dissection (ALND). Conclusion This paper concludes that the technology of SLN tracer method with methylene blue breast glands axillary tail injection can be applied in clinic and SLNB can be applied in prognosis of axillary lymph node metastasis (ALNM).

  5. Blood tracer kinetics in the arterial tree.

    Directory of Open Access Journals (Sweden)

    Elias Kellner

    Full Text Available Evaluation of blood supply of different organs relies on labeling blood with a suitable tracer. The tracer kinetics is linear: Tracer concentration at an observation site is a linear response to an input somewhere upstream the arterial flow. The corresponding impulse response functions are currently treated empirically without incorporating the relation to the vascular morphology of an organ. In this work we address this relation for the first time. We demonstrate that the form of the response function in the entire arterial tree is reduced to that of individual vessel segments under approximation of good blood mixing at vessel bifurcations. The resulting expression simplifies significantly when the geometric scaling of the vascular tree is taken into account. This suggests a new way to access the vascular morphology in vivo using experimentally determined response functions. However, it is an ill-posed inverse problem as demonstrated by an example using measured arterial spin labeling in large brain arteries. We further analyze transport in individual vessel segments and demonstrate that experimentally accessible tracer concentration in vessel segments depends on the measurement principle. Explicit expressions for the response functions are obtained for the major middle part of the arterial tree in which the blood flow in individual vessel segments can be treated as laminar. When applied to the analysis of regional cerebral blood flow measurements for which the necessary arterial input is evaluated in the carotid arteries, present theory predicts about 20% underestimation, which is in agreement with recent experimental data.

  6. Blood tracer kinetics in the arterial tree.

    Science.gov (United States)

    Kellner, Elias; Gall, Peter; Günther, Matthias; Reisert, Marco; Mader, Irina; Fleysher, Roman; Kiselev, Valerij G

    2014-01-01

    Evaluation of blood supply of different organs relies on labeling blood with a suitable tracer. The tracer kinetics is linear: Tracer concentration at an observation site is a linear response to an input somewhere upstream the arterial flow. The corresponding impulse response functions are currently treated empirically without incorporating the relation to the vascular morphology of an organ. In this work we address this relation for the first time. We demonstrate that the form of the response function in the entire arterial tree is reduced to that of individual vessel segments under approximation of good blood mixing at vessel bifurcations. The resulting expression simplifies significantly when the geometric scaling of the vascular tree is taken into account. This suggests a new way to access the vascular morphology in vivo using experimentally determined response functions. However, it is an ill-posed inverse problem as demonstrated by an example using measured arterial spin labeling in large brain arteries. We further analyze transport in individual vessel segments and demonstrate that experimentally accessible tracer concentration in vessel segments depends on the measurement principle. Explicit expressions for the response functions are obtained for the major middle part of the arterial tree in which the blood flow in individual vessel segments can be treated as laminar. When applied to the analysis of regional cerebral blood flow measurements for which the necessary arterial input is evaluated in the carotid arteries, present theory predicts about 20% underestimation, which is in agreement with recent experimental data.

  7. Fractal tracer distributions in turbulent field theories

    DEFF Research Database (Denmark)

    Hansen, J. Lundbek; Bohr, Tomas

    1998-01-01

    We study the motion of passive tracers in a two-dimensional turbulent velocity field generated by the Kuramoto-Sivashinsky equation. By varying the direction of the velocity-vector with respect to the field-gradient we can continuously vary the two Lyapunov exponents for the particle motion and t...

  8. Using neural networks to describe tracer correlations

    Directory of Open Access Journals (Sweden)

    D. J. Lary

    2004-01-01

    Full Text Available Neural networks are ideally suited to describe the spatial and temporal dependence of tracer-tracer correlations. The neural network performs well even in regions where the correlations are less compact and normally a family of correlation curves would be required. For example, the CH4-N2O correlation can be well described using a neural network trained with the latitude, pressure, time of year, and methane volume mixing ratio (v.m.r.. In this study a neural network using Quickprop learning and one hidden layer with eight nodes was able to reproduce the CH4-N2O correlation with a correlation coefficient between simulated and training values of 0.9995. Such an accurate representation of tracer-tracer correlations allows more use to be made of long-term datasets to constrain chemical models. Such as the dataset from the Halogen Occultation Experiment (HALOE which has continuously observed CH4  (but not N2O from 1991 till the present. The neural network Fortran code used is available for download.

  9. Nanoparticle tracers in calcium carbonate porous media

    KAUST Repository

    Li, Yan Vivian

    2014-07-15

    Tracers are perhaps the most direct way of diagnosing subsurface fluid flow pathways for ground water decontamination and for natural gas and oil production. Nanoparticle tracers could be particularly effective because they do not diffuse away from the fractures or channels where flow occurs and thus take much less time to travel between two points. In combination with a chemical tracer they can measure the degree of flow concentration. A prerequisite for tracer applications is that the particles are not retained in the porous media as the result of aggregation or sticking to mineral surfaces. By screening eight nanoparticles (3-100 nm in diameter) for retention when passed through calcium carbonate packed laboratory columns in artificial oil field brine solutions of variable ionic strength we show that the nanoparticles with the least retention are 3 nm in diameter, nearly uncharged, and decorated with highly hydrophilic polymeric ligands. The details of these column experiments and the tri-modal distribution of zeta potential of the calcite sand particles in the brine used in our tests suggests that parts of the calcite surface have positive zeta potential and the retention of negatively charged nanoparticles occurs at these sites. Only neutral nanoparticles are immune to at least some retention. © 2014 Springer Science+Business Media.

  10. The orbital PDF: general inference of the gravitational potential from steady-state tracers

    CERN Document Server

    Han, Jiaxin; Cole, Shaun; Frenk, Carlos S

    2015-01-01

    We develop two general methods to infer the gravitational potential of a system using steady-state tracers, i.e., tracers with a time-independent phase-space distribution. Combined with the phase-space continuity equation, the time independence implies a universal Orbital Probability Density Function (oPDF) $\\mathrm{d} P(\\lambda|{\\rm orbit})\\propto \\mathrm{d} t$, where $\\lambda$ is the coordinate of the particle along the orbit. The oPDF is equivalent to Jeans theorem, and is the key physical ingredient behind most dynamical modelling of steady-state tracers. In the case of a spherical potential, we develop a likelihood estimator that fits analytical potentials to the system, and a non-parametric method ("Phase-Mark") that reconstructs the potential profile, both assuming only the oPDF. The methods involve no extra assumptions about the tracer distribution function and can be applied to tracers with any arbitrary distribution of orbits, with possible extension to non-spherical potentials. The methods are test...

  11. Carbon Monoxide Poisoning - Multiple Languages: MedlinePlus

    Science.gov (United States)

    ... sharing features on this page, please enable JavaScript. Amharic (amarunya) Arabic (العربية) Chinese - Traditional (繁體中文) French (français) ... Kiswahili) Tagalog (Tagalog) Tigrinya (tigrinya) Vietnamese (Tiếng Việt) Amharic (amarunya) Prevention Guidelines: You Can Prevent Carbon Monoxide ...

  12. Pathways and bioenergetics of anaerobic carbon monoxide fermentation

    NARCIS (Netherlands)

    Diender, Martijn; Stams, Fons; Machado de Sousa, Diana

    2015-01-01

    Carbon monoxide can act as a substrate for different modes of fermentative anaerobic metabolism. The trait of utilizing CO is spread among a diverse group of microorganisms, including members of bacteria as well as archaea. Over the last decade this metabolism has gained interest due to the poten

  13. UV-induced carbon monoxide emission from living vegetation

    DEFF Research Database (Denmark)

    Bruhn, Dan; Albert, Kristian Rost; Mikkelsen, Teis Nørgaard

    2013-01-01

    The global burden of carbon monoxide (CO) is rather uncertain. In this paper we address the potential for UV-induced CO emission by living terrestrial vegetation surfaces. Real-time measurements of CO concentrations were made with a cavity enhanced laser spectrometer connected in closed loop...

  14. Study on Response Time of SPE Carbon Monoxide Sensor

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The influence of structural design and the parameters of the working electrode on the response time of a solid polymer electrolyte (SPE) carbon monoxide sensor has been studied. Results show that the response time is mainly determined by the RC time constant of the catalyst layer and also related with the working electrode potential.

  15. Hydrogen, carbon monoxide, and methane in the marine environment

    OpenAIRE

    Bullister, John Logan

    1980-01-01

    EXTRACT (SEE PDF FOR FULL ABSTRACT): The horizontal and vertical distribution of three dissolved trace gases, namely molecular hydrogen, carbon monoxide, and methane, was measured in coastal and oceanic areas. Atmospheric concentrations of these gases were measured both at locations influenced by nearby human activity, and in areas far removed from these inputs.

  16. Carbon monoxide poisoning mimicking long-QT induced syncope

    NARCIS (Netherlands)

    I.M. Onvlee-Dekker (Irene); A.C.H. de Vries (Andrica); A.D.J. ten Harkel (Arend)

    2007-01-01

    textabstractCarbon monoxide (CO)poisoning is a rare cause of QT prolongation, and is therefore easily missed. The case of a patient with unexplained syncope and QT prologation on the electrocardiogram that turned out to be related to CO poisoning is reported here. In patients with QT prolongation,

  17. Evaluation of parameter uncertainties obtained from in-situ tracer experiments

    Energy Technology Data Exchange (ETDEWEB)

    Sawada, Atsushi; Yoshino, Naoto [Japan Nuclear Cycle Development Inst., Tokai Works, Tokai, Ibaraki (Japan); Ijiri, Yuji; Hata, Akihito [Taisei Corp., Tokyo (Japan); Hosono, Kenichi [Geoscience Research Laboratory, Yamato, Kanagawa (Japan)

    2003-03-01

    Radionuclide transport parameter uncertainty is an important consideration in the safety assessment of high-level radioactive waste disposal. This paper describes the development of a method for the quantitative estimation of transport parameter uncertainties from in-situ tracer experiments. The method utilizes a probabilistic inversion based on the maximum likelihood method. Transport parameters and their uncertainties are derived from a series of conservative and reactive tracer tests conducted in a single fracture at the Aespoe Hard Rock Laboratory in Sweden. These transport parameters and uncertainties are useful for evaluating the influence of parameter uncertainty on safety assessment. (author)

  18. Nitrous oxide as a tracer gas in the ASHRAE 110-1995 Standard.

    Science.gov (United States)

    Burke, Martin; Wong, Larry; Gonzales, Ben A; Knutson, Gerhard

    2014-01-01

    ANSI/ASHRAE Standard 110 provides a quantitative method for testing the performance of laboratory fume hoods. Through release of a known quantity (4.0 Lpm) of a tracer gas, and subsequent monitoring of the tracer gas concentration in the "breathing zone" of a mannequin positioned in front of the hood, this method allows for evaluation of laboratory hood performance. Standard 110 specifies sulfur hexafluoride (SF6) as the tracer gas; however, suitable alternatives are allowed. Through three series of performance tests, this analysis serves to investigate the use of nitrous oxide (N2O) as an alternate tracer gas for hood performance testing. Single gas tests were performed according to ASHRAE Standard 110-1995 with each tracer gas individually. These tests showed identical results using an acceptance criterion of AU 0.1 with the sash half open, nominal 18 inches (0.46m) high, and the face velocity at a nominal 60 fpm (0.3 m/s). Most data collected in these single gas tests, for both tracer gases, were below the minimum detection limit, thus two dual gas tests were developed for simultaneous sampling of both tracer gases. Dual gas dual ejector tests were performed with both tracer gases released simultaneously through two ejectors, and the concentration measured with two detectors using a common sampling probe. Dual gas single ejector tests were performed with both tracer gases released though a single ejector, and the concentration measured in the same manner as the dual gas dual ejector tests. The dual gas dual ejector tests showed excellent correlation, with R typically greater than 0.9. Variance was observed in the resulting regression line for each hood, likely due to non-symmetry between the two challenges caused by variables beyond the control of the investigators. Dual gas single ejector tests resulted in exceptional correlation, with R>0.99 typically for the consolidated data, with a slope of 1.0. These data indicate equivalent results for ASHRAE 110

  19. Separation of emitted and photochemical formaldehyde in Mexico City using a statistical analysis and a new pair of gas-phase tracers

    Science.gov (United States)

    Garcia, A. R.; Volkamer, R.; Molina, L. T.; Molina, M. J.; Samuelson, J.; Mellqvist, J.; Galle, B.; Herndon, S. C.; Kolb, C. E.

    2006-10-01

    Photochemical pollution control strategies require an understanding of photochemical oxidation precursors, making it important to distinguish between primary and secondary sources of HCHO. Estimates for the relative strengths of primary and secondary sources of formaldehyde (HCHO) were obtained using a statistical regression analysis with time series data of carbon monoxide (CO) and glyoxal (CHOCHO) measured in the Mexico City Metropolitan Area (MCMA) during the spring of 2003. Differences between Easter week and more typical weeks are evaluated. The use of CO-CHOCHO as HCHO tracers is more suitable for differentiating primary and secondary sources than CO-O3. The application of the CO-O3 tracer pair to mobile laboratory data suggests a potential in-city source of background HCHO. A significant amount of HCHO observed in the MCMA is associated with primary emissions.

  20. Separation of emitted and photochemical formaldehyde in Mexico City using a statistical analysis and a new pair of gas-phase tracers

    Directory of Open Access Journals (Sweden)

    A. R. Garcia

    2006-01-01

    Full Text Available Photochemical pollution control strategies require an understanding of photochemical oxidation precursors, making it important to distinguish between primary and secondary sources of HCHO. Estimates for the relative strengths of primary and secondary sources of formaldehyde (HCHO were obtained using a statistical regression analysis with time series data of carbon monoxide (CO and glyoxal (CHOCHO measured in the Mexico City Metropolitan Area (MCMA during the spring of 2003. Differences between Easter week and more typical weeks are evaluated. The use of CO-CHOCHO as HCHO tracers is more suitable for differentiating primary and secondary sources than CO-O3. The application of the CO-O3 tracer pair to mobile laboratory data suggests a potential in-city source of background HCHO. A significant amount of HCHO observed in the MCMA is associated with primary emissions.

  1. Separation of emitted and photochemical formaldehyde in Mexico City using a statistical analysis and a new pair of gas-phase tracers

    Directory of Open Access Journals (Sweden)

    A. R. García

    2005-11-01

    Full Text Available Photochemical pollution control strategies require an understanding of photochemical oxidation precursors, making it important to distinguish between primary and secondary sources of HCHO. Estimates for the relative strengths of primary and secondary sources of formaldehyde (HCHO were obtained using a statistical regression analysis with time series data of carbon monoxide (CO and glyoxal (CHOCHO measured in the Mexico City Metropolitan Area (MCMA during the spring of 2003. Differences between Easter week and more typical weeks are evaluated. The use of CO-CHOCHO as HCHO tracers is more suitable for differentiating primary and secondary sources than CO-O3. The application of the CO-O3 tracer pair to mobile laboratory data suggests a potential in-city source of background HCHO. A significant amount of HCHO observed in the MCMA is associated with primary emissions.

  2. Exhaled carbon monoxide in asthmatics: a meta-analysis

    Directory of Open Access Journals (Sweden)

    Huang Mao

    2010-04-01

    Full Text Available Abstract Background The non-invasive assessment of airway inflammation is potentially advantageous in asthma management. Exhaled carbon monoxide (eCO measurement is cheap and has been proposed to reflect airway inflammation and oxidative stress but current data are conflicting. The purpose of this meta-analysis is to determine whether eCO is elevated in asthmatics, is regulated by steroid treatment and reflects disease severity and control. Methods A systematic search for English language articles published between 1997 and 2009 was performed using Medline, Embase and Cochrane databases. Observational studies comparing eCO in non-smoking asthmatics and healthy subjects or asthmatics before and after steroid treatment were included. Data were independently extracted by two investigators and analyzed to generate weighted mean differences using either a fixed or random effects meta-analysis depending upon the degree of heterogeneity. Results 18 studies were included in the meta-analysis. The eCO level was significantly higher in asthmatics as compared to healthy subjects and in intermittent asthma as compared to persistent asthma. However, eCO could not distinguish between steroid-treated asthmatics and steroid-free patients nor separate controlled and partly-controlled asthma from uncontrolled asthma in cross-sectional studies. In contrast, eCO was significantly reduced following a course of corticosteroid treatment. Conclusions eCO is elevated in asthmatics but levels only partially reflect disease severity and control. eCO might be a potentially useful non-invasive biomarker of airway inflammation and oxidative stress in nonsmoking asthmatics.

  3. Magnetic Resonance Imaging Findings in Chronic Carbon Monoxide Intoxication

    Energy Technology Data Exchange (ETDEWEB)

    Durak, A. C.; Coskun, A.; Yikilmaz, A.; Erdogan, F.; Mavili, E.; Guven, M. [Hospital of Erciyes Univ., Kayseri (Turkey). Dept. of Radiology

    2005-05-01

    Purpose: To define the cranial magnetic resonance imaging (MRI) features of the chronic stage of carbon monoxide (CO) poisoning in patients with and without neuropsychiatric sequelae. Material and Methods: Eight patients who had neither symptoms nor neurological sequelae and eight patients with neuropsychiatric sequelae were included in the study. Patients aged between 9 to 57 (mean 32.2 years). All patients had been comatose at initial admittance and awoke after normobaric 100% oxygen therapy within 1-7 days. In this study, the patients were being examined with routine cranial MRI between 1 and 10 years (mean 3.4 years) after exposure to CO. Results: The most common finding was bilateral symmetric hyperintensity of the white matter, which was more significant in the centrum semiovale, with relative sparing of the temporal lobes and anterior parts of the frontal lobes on T2-weighted and FLAIR images in all patients. Cerebral cortical atrophy was seen in 10 patients; mild atrophy of cerebellar hemispheres in 8; and vermian atrophy in 11. Corpus callosum was atrophic in one patient. Bilateral globus pallidus lesions were seen in three patients. The lesions were hypointense on T1-weighted images and hyperintense on T2-weighted and FLAIR images. Conclusion: Patients with severe CO intoxication may develop persistent cerebral changes independently of their neuropsychiatric findings in the chronic stage. They may present with characteristic MRI findings as described here, even if asymptomatic. The history of CO exposure is therefore helpful for recognizing and interpreting the MRI findings of chronic stage CO intoxication.

  4. An inexpensive field fluorometer for hydrogeological tracer tests with three tracers and turbidity measurement

    OpenAIRE

    Schnegg, Pierre-André

    2005-01-01

    The Geomagnetism Group of the University of Neuchâtel has recently designed a flow-through field fluorometer with added spectral capabilities for hydrological tracer tests. This instrument is equipped with four optical axes allowing water sample illumination with four independent light sources at different wavelenghs covering the full spectrum from UV to red. As many as three conveniently selected (dye) tracers can be simultaneously measured and separeted from a cocktail. Careful turbidity me...

  5. EVALUATION OF LEAKAGE FROM FUME HOODS USING TRACER GAS, TRACER NANOPARTICLES AND NANOPOWDER HANDLING TEST METHODOLOGIES

    OpenAIRE

    Dunn, Kevin H.; Tsai, Candace Su-Jung; Woskie, Susan R.; Bennett, James S.; Garcia, Alberto; Ellenbecker, Michael J.

    2014-01-01

    The most commonly reported control used to minimize workplace exposures to nanomaterials is the chemical fume hood. Studies have shown, however, that significant releases of nanoparticles can occur when materials are handled inside fume hoods. This study evaluated the performance of a new commercially available nano fume hood using three different test protocols. Tracer gas, tracer nanoparticle, and nanopowder handling protocols were used to evaluate the hood. A static test procedure using tr...

  6. DFT studies on the SCR reaction mechanism of nitrogen monoxide with propylene catalyzed by copper oxide

    Institute of Scientific and Technical Information of China (English)

    TIAN Ying; XU Jing; ZHAO Jing-xiang

    2007-01-01

    The SCR reaction mechanism of NO with C3H6catalyzed by CuO was studied by the method of Density Functional Theory (DFT) at the B3LYP/LanL2DZ levels. The optimized geometries of the stationary points on the potential surface were obtained and the transition state was confirmed by IRC and vibration analysis. The activation energy was calculated being 34. 26 kJ/mol. It was shown that propylene reacted firstly with Cu forming intermediate, and then nitrogen monoxide immediately reacted with the intermediate to be reduced. It was proved to be a direct interaction mechanism.

  7. Rebuilding sources of linear tracers after atmospheric concentration concentration

    Directory of Open Access Journals (Sweden)

    J.-P. Issartel

    2003-06-01

    Full Text Available The identification of widespread sources of passive tracers out of atmospheric concentration measurements has become an important challenge of modern meteorology. The paper proposes some mathematical tracks to address this reconstruction of the complex space-time geometry of the sources. The methods are based upon the use of retroplumes. The inverse problem is addressed in a deterministic non statistical frame. The information obtained by local measurements is spread by introducing the concept of illumination. The constraint that the source to be rebuilt is non negative is also addressed. The experimental source ETEX1 is rebuilt in order to evaluate an impulse response of the algorithms.

  8. Geotropic tracers in turbulent flows: a proxy for fluid acceleration

    CERN Document Server

    Boffetta, Guido; De Lillo, Filippo; Santamaria, Francesco

    2013-01-01

    We investigate the statistics of orientation of small, neutrally buoyant, spherical tracers whose center of mass is displaced from the geometrical center. If appropriate-sized particles are considered, a linear relation can be derived between the horizontal components of the orientation vector and the same components of acceleration. Direct numerical simulations are carried out, showing that such relation can be used to reconstruct the statistics of acceleration fluctuations up to the order of the gravitational acceleration. Based on such results, we suggest a novel method for the local experimental measurement of accelerations in turbulent flows.

  9. Accurate blood flow measurements: are artificial tracers necessary?

    Science.gov (United States)

    Poelma, Christian; Kloosterman, Astrid; Hierck, Beerend P; Westerweel, Jerry

    2012-01-01

    Imaging-based blood flow measurement techniques, such as particle image velocimetry, have become an important tool in cardiovascular research. They provide quantitative information about blood flow, which benefits applications ranging from developmental biology to tumor perfusion studies. Studies using these methods can be classified based on whether they use artificial tracers or red blood cells to visualize the fluid motion. We here present the first direct comparison in vivo of both methods. For high magnification cases, the experiments using red blood cells strongly underestimate the flow (up to 50% in the present case), as compared to the tracer results. For medium magnification cases, the results from both methods are indistinguishable as they give the same underestimation of the real velocities (approximately 33%, based on in vitro reference measurements). These results suggest that flow characteristics reported in literature cannot be compared without a careful evaluation of the imaging characteristics. A method to predict the expected flow averaging behavior for a particular facility is presented.

  10. Accurate blood flow measurements: are artificial tracers necessary?

    Directory of Open Access Journals (Sweden)

    Christian Poelma

    Full Text Available Imaging-based blood flow measurement techniques, such as particle image velocimetry, have become an important tool in cardiovascular research. They provide quantitative information about blood flow, which benefits applications ranging from developmental biology to tumor perfusion studies. Studies using these methods can be classified based on whether they use artificial tracers or red blood cells to visualize the fluid motion. We here present the first direct comparison in vivo of both methods. For high magnification cases, the experiments using red blood cells strongly underestimate the flow (up to 50% in the present case, as compared to the tracer results. For medium magnification cases, the results from both methods are indistinguishable as they give the same underestimation of the real velocities (approximately 33%, based on in vitro reference measurements. These results suggest that flow characteristics reported in literature cannot be compared without a careful evaluation of the imaging characteristics. A method to predict the expected flow averaging behavior for a particular facility is presented.

  11. Using REE Tracers to Measure Sheet Erosion Changing to Rill Erosion

    Institute of Scientific and Technical Information of China (English)

    宋炜; 刘普灵; 杨明义; 薛亚洲

    2003-01-01

    Rare earth element(REE) tracer method was used to study sheet erosion changing to rill erosion on slope land. By placing different REE on different soil depth across a slope in an indoor plot, two simulated rainfalls were applied to study the change of erosion type and the rill erosion process. The results indicate that the main erosion type is sheet erosion at the beginning of the rainfalls, and serious erosion happens after rill erosion appears. Accumulated sheet and rill erosion amount increases with the rainfalls time. The percentage of sheet erosion amount decreases and rill erosion percentage increases with time. At the end of the rainfalls, the total rill erosion amounts are 4.3 and 5 times more than sheet erosion. In this paper, a new REE tracer method was used to quantitatively distinguish sheet and rill erosion amount. The new REE tracer method should be useful to future studying of erosion processes on slope lands.

  12. PET tracers for somatostatin receptor imaging of neuroendocrine tumors

    DEFF Research Database (Denmark)

    Johnbeck, Camilla Bardram; Knigge, Ulrich; Kjær, Andreas

    2014-01-01

    Neuroendocrine tumors have shown rising incidence mainly due to higher clinical awareness and better diagnostic tools over the last 30 years. Functional imaging of neuroendocrine tumors with PET tracers is an evolving field that is continuously refining the affinity of new tracers in the search...... these PET tracers further....

  13. Optimal tracers for parallel labeling experiments and (13)C metabolic flux analysis: A new precision and synergy scoring system.

    Science.gov (United States)

    Crown, Scott B; Long, Christopher P; Antoniewicz, Maciek R

    2016-11-01

    (13)C-Metabolic flux analysis ((13)C-MFA) is a widely used approach in metabolic engineering for quantifying intracellular metabolic fluxes. The precision of fluxes determined by (13)C-MFA depends largely on the choice of isotopic tracers and the specific set of labeling measurements. A recent advance in the field is the use of parallel labeling experiments for improved flux precision and accuracy. However, as of today, no systemic methods exist for identifying optimal tracers for parallel labeling experiments. In this contribution, we have addressed this problem by introducing a new scoring system and evaluating thousands of different isotopic tracer schemes. Based on this extensive analysis we have identified optimal tracers for (13)C-MFA. The best single tracers were doubly (13)C-labeled glucose tracers, including [1,6-(13)C]glucose, [5,6-(13)C]glucose and [1,2-(13)C]glucose, which consistently produced the highest flux precision independent of the metabolic flux map (here, 100 random flux maps were evaluated). Moreover, we demonstrate that pure glucose tracers perform better overall than mixtures of glucose tracers. For parallel labeling experiments the optimal isotopic tracers were [1,6-(13)C]glucose and [1,2-(13)C]glucose. Combined analysis of [1,6-(13)C]glucose and [1,2-(13)C]glucose labeling data improved the flux precision score by nearly 20-fold compared to widely use tracer mixture 80% [1-(13)C]glucose +20% [U-(13)C]glucose.

  14. Tracer SWIW tests in propped and un-propped fractures: parameter sensitivity issues, revisited

    Science.gov (United States)

    Ghergut, Julia; Behrens, Horst; Sauter, Martin

    2017-04-01

    Single-well injection-withdrawal (SWIW) or 'push-then-pull' tracer methods appear attractive for a number of reasons: less uncertainty on design and dimensioning, and lower tracer quantities required than for inter-well tests; stronger tracer signals, enabling easier and cheaper metering, and shorter metering duration required, reaching higher tracer mass recovery than in inter-well tests; last not least: no need for a second well. However, SWIW tracer signal inversion faces a major issue: the 'push-then-pull' design weakens the correlation between tracer residence times and georeservoir transport parameters, inducing insensitivity or ambiguity of tracer signal inversion w. r. to some of those georeservoir parameters that are supposed to be the target of tracer tests par excellence: pore velocity, transport-effective porosity, fracture or fissure aperture and spacing or density (where applicable), fluid/solid or fluid/fluid phase interface density. Hydraulic methods cannot measure the transport-effective values of such parameters, because pressure signals correlate neither with fluid motion, nor with material fluxes through (fluid-rock, or fluid-fluid) phase interfaces. The notorious ambiguity impeding parameter inversion from SWIW test signals has nourished several 'modeling attitudes': (i) regard dispersion as the key process encompassing whatever superposition of underlying transport phenomena, and seek a statistical description of flow-path collectives enabling to characterize dispersion independently of any other transport parameter, as proposed by Gouze et al. (2008), with Hansen et al. (2016) offering a comprehensive analysis of the various ways dispersion model assumptions interfere with parameter inversion from SWIW tests; (ii) regard diffusion as the key process, and seek for a large-time, asymptotically advection-independent regime in the measured tracer signals (Haggerty et al. 2001), enabling a dispersion-independent characterization of multiple

  15. 染料示踪法联合荧光示踪法提高乳腺癌前哨淋巴结活检术成功率%Success Rate of Sentinel Lymph Node Biopsy in Breast Cancer Increased by Combined Tracer Method of Fluorescence and Dye

    Institute of Scientific and Technical Information of China (English)

    崔嵘嵘; 林晓燕; 许诚; 胡贇宏; 王铮元; 蔡丰丰

    2016-01-01

    杂作用后,采用染料示踪法联合荧光示踪法 SLNB 成功率高于采用染料示踪法(χ2MH=26.686,P ﹤0.001,ORMH =3.928)。Logistic 回归分析结果显示,示踪法、BMI、年龄是 SLNB 结果的影响因素(P﹤0.05)。Logistic 回归模型分类预测准确率为80.2%。结论染料示踪法联合荧光示踪法可有效提高乳腺癌 SLNB 成功率,值得临床推荐使用。%Background The sentinel lymph node biopsy(SLNB)of breast cancer is gaining increased attention in recent years,and the choosing of tracer is of great importance in its success rate. Objective To evaluate the clinical effectiveness and application value of the combined tracer method of fluorescence and dye in SLNB of breast cancer. Methods According to the inclusion criteria of the study,449 patients with primarily invasive breast cancer,who received treatment in Department of Breast Surgery of Yangpu Hospital,Tongji University from January 2010 to September 2015,were selected as research objects. Patients were divided into group A(226 patients with dye tracer method)and group B(223 patients with the combined tracer method of fluorescence and dye)by random number table method. The general information〔 including age,body mass index(BMI)〕of patients were collected,the success rate of patients' SLNB were calculated. Stratified analysis of patients were made based on their BMI(≤22. 5 kg/ m2 and ﹥ 22. 5 kg/ m2 )and age(≤55 and ﹥ 55). Results BMI and age in group A were less than those in group B(P ﹤ 0. 05). Among the 223 patients(BMI≤22. 5 kg/ m2 ),the success rate of SLNB with combined tracer method of fluorescence and dye〔94. 7%(108 / 114)〕was higher than that of SLNB with dye tracer method〔78. 0%(85 / 109)〕〔OR = 5. 082,95% CI(1. 988,12. 993)〕. Among the 226 patients(BMI ﹥ 22. 5 kg/ m2 ),the success rate of SLNB with combined tracer method of fluorescence and dye〔85. 3%(93 / 109)〕was higher than that of SLNB with dye

  16. Identification and characterization of conservative organic tracers for use as hydrologic tracers for the Yucca Mountain site characterization study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Stetzenbach, K.; Farnham, I.

    1996-06-01

    Extensive tracer testing is expected to take place at the C-well complex in the Nevada Test Site as part of the Yucca Mountain Site Characterization Project. The C-well complex consists of one pumping well, C3, and two injection wells, C1 and C2 into which tracer will be introduced. The goal of this research was to provide USGS with numerous tracers to completed these tests. Several classes of fluorinated organic acids have been evaluated. These include numerous isomers of fluorinated benzoic acids, cinnamic acids, and salicylic acids. Also several derivatives of 2-hydroxy nicotinic acid (pyridone) have been tested. The stability of these compounds was determined using batch and column tests. Ames testing (mutagenicity/carcinogenicity) was conducted on the fluorinated benzoic acids and a literature review of toxicity of the fluorobenzoates and three perfluoro aliphatic acids was prepared. Solubilities were measured and method development work was performed to optimize the detection of these compounds. A Quality Assurance (QA) Program was developed under existing DOE and USGS guidelines. The program includes QA procedures and technical standard operating procedures. A tracer test, using sodium iodide, was performed at the C-well complex. HRC chemists performed analyses on site, to provide real time data for the USGS hydrologists and in the laboratories at UNLV. Over 2,500 analyses were performed. This report provides the results of the laboratory experiments and literature reviews used to evaluate the potential tracers and reports on the results of the iodide C-well tracer test.

  17. Stream flow rate measurement using tracer techniques at the Kemubu Agricultural Development Authority (KADA), Kelantan

    Energy Technology Data Exchange (ETDEWEB)

    Daud Mohammad; Abd Razak Hamzah; Wan Abd Aziz Wan Mohamad; Juhari Yusoff; Wan Zakaria Wan Mohd Tahir

    1985-06-01

    Measuring the flow rate of a water course is one of the basic operations in hydrology, being of general relevance to water problems and of particular importance in the planning of water control schemes. The techniques commonly used in streamflow gauging are either by a current meter of tracer dilution method. This paper describes the latter technique in which radioisotope Tc-99m was used as a tracer in streamflow measurements performed in 1983 in a few selected irrigation canals and pump house under the Kemubu Agriculture Development Authority (KADA), Kelantan. Total count technique and peak-to-peak method were adopted in this study. (author).

  18. Use of tracers to investigate drilling-fluid invasion and oil flushing during coring

    Energy Technology Data Exchange (ETDEWEB)

    Brown, A.; Marriott, F.T. (Texaco, Inc., Houston, TX (US))

    1988-11-01

    This work develops a method in which chemical tracers in the drilling fluid help determine mud filtrate invasion and the degree of oil flushing during coring of steamed and unsteamed heavy-oil formations. Salts of iodide and bromide were added to the drilling fluid while Well TO3 was cored through the Lombardi and Aurignac zones at San Ardo field in California. Vertical core plugs, taken from the periphery to the center of the retrieved whole core, were analyzed for tracer concentration. Tracer analyses indicated minimal filtrate invasion in the not-yet-steamflooded Lombardi zone and complete filtrate invasion in the steamflooded Aurignac zone. Tracer and oil saturation analyses showed the Lombardi zone to be uniform from top to bottom with an average oil saturation of 42.5% and an average porosity of 31.1%. Interpretation of tracer and oil saturation data permitted the construction of a layered model for the Aurignac zone. The layers ranged from an average oil saturation of 8% in the steamflooded layer to 37% in the bottom layer. The data showed that significant oil flushing (6%) occurred only in cores taken from the hot-waterflooded layer just below the steam zone. Vertical core-plug porosities and saturations, as determined by a unique calculating scheme, were compared with conventional and Elkins-corrected values. The comparison indicated that misapplication of the Elkins method in high-temperature formations may result in significant errors.

  19. Combining 3D Hydraulic Tomography with Tracer Tests for Improved Transport Characterization.

    Science.gov (United States)

    Sanchez-León, E; Leven, C; Haslauer, C P; Cirpka, O A

    2016-07-01

    Hydraulic tomography (HT) is a method for resolving the spatial distribution of hydraulic parameters to some extent, but many details important for solute transport usually remain unresolved. We present a methodology to improve solute transport predictions by combining data from HT with the breakthrough curve (BTC) of a single forced-gradient tracer test. We estimated the three dimensional (3D) hydraulic-conductivity field in an alluvial aquifer by inverting tomographic pumping tests performed at the Hydrogeological Research Site Lauswiesen close to Tübingen, Germany, using a regularized pilot-point method. We compared the estimated parameter field to available profiles of hydraulic-conductivity variations from direct-push injection logging (DPIL), and validated the hydraulic-conductivity field with hydraulic-head measurements of tests not used in the inversion. After validation, spatially uniform parameters for dual-domain transport were estimated by fitting tracer data collected during a forced-gradient tracer test. The dual-domain assumption was used to parameterize effects of the unresolved heterogeneity of the aquifer and deemed necessary to fit the shape of the BTC using reasonable parameter values. The estimated hydraulic-conductivity field and transport parameters were subsequently used to successfully predict a second independent tracer test. Our work provides an efficient and practical approach to predict solute transport in heterogeneous aquifers without performing elaborate field tracer tests with a tomographic layout.

  20. Electrical Imaging of Tracer Migration at the Massachusetts Military Reservation, Cape Cod

    Science.gov (United States)

    Singha, K.; Binley, A. M.; Gorelick, S. M.

    2002-12-01

    Accurately characterizing flow and solute transport in groundwater systems is a critical problem in hydrology. Given the large volume of data required to develop an accurate model of subsurface flow, and the cost of direct sampling, the use of geophysical methods can contribute significantly to information about the subsurface. Electrical resistance tomography (ERT) is examined as a method to provide spatially continuous information about aquifer properties. The primary goal of this study is to use ERT to map subsurface flow paths in detail. High-resolution images of the movement of a tracer in two- and three-dimensions help delineate aquifer heterogeneity. Field data were acquired at the U.S. Geological Survey research site at the Massachusetts Military Reservation, Cape Cod during the summer of 2002. ERT was used to track the flow and transport of an electrically conductive sodium chloride tracer introduced over 9 hours during a two-well tracer test. Three hundred and fifty 2-D data sets were collected between four corner-point wells for 20 days following the injection, combining to form approximately sixty 3-D data sets. Concentrations were measured at a multilevel sampler centrally located within the ERT array and at the production well. The tomograms indicate the movement of the saline tracer that correspond well with measured concentration data, and the resistivity inversions serve as an appropriate surrogate for concentration measurements that are otherwise impossible to obtain. Under reasonable assumptions, groundwater velocity estimates and hydraulic conductivity can be obtained by tracking the tracer.

  1. Tracer Diffusion Mechanism in Amorphous Solids

    Directory of Open Access Journals (Sweden)

    P. K. Hung

    2011-01-01

    Full Text Available Tracer diffusion in amorphous solid is studied by mean of nB-bubble statistic. The nB-bubble is defined as a group of atoms around a spherical void and large bubble that represents a structural defect which could be eliminated under thermal annealing. It was found that amorphous alloys such as CoxB100−x (x=90, 81.5 and 70 and Fe80P20 suffer from a large number of vacancy bubbles which function like diffusion vehicle. The concentration of vacancy bubble weakly depends on temperature, but essentially on the relaxation degree of considered sample. The diffusion coefficient estimated for proposed mechanism via vacancy bubbles is in a reasonable agreement with experiment for actual amorphous alloys. The relaxation effect for tracer diffusion in amorphous alloys is interpreted by the elimination of vacancy bubbles under thermal annealing.

  2. Plutonium as a tracer for soil erosion assessment in northeast China

    DEFF Research Database (Denmark)

    Xu, Yihong; Qiao, Jixin; Pan, Shaoming;

    2015-01-01

    Soil erosion is one of the most serious environmental and agricultural problems faced by human society. Assessing intensity is an important issue for controlling soil erosion and improving eco-environmental quality. The suitability of the application of plutonium (Pu) as a tracer for soil erosion...... assessment in northeast China was investigated by comparing with that of 137Cs. Here we build on preliminary work, in which we investigated the potential of Pu as a soil erosion tracer by sampling additional reference sites and potential erosive sites, along the Liaodong Bay region in northeast China, for Pu...... in cultivated land. The baseline inventories of 239+240Pu and 137Cs were 88.4 and 1688Bqm-2 respectively. Soil erosion rates estimated by 239+240Pu tracing method were consistent with those obtained by the 137Cs method, confirming that Pu is an effective tracer with a similar tracing behavior to that of 137Cs...

  3. The medical applications of radioactive tracers

    Energy Technology Data Exchange (ETDEWEB)

    Hamilton, J.G.

    1947-12-31

    This report provides a broad yet in depth overview of the use of radioactive materials as tracers in medicine and biology for the period of 1935--1947. Particular attention is paid to is of radio-sodium, radio-iodine, radio-iron, radio-phosphorus, radio-strontium, and fission products. The main thrust of this paper is human rather than animal work and focuses in work that has been published.

  4. Molecules as tracers of galaxy evolution

    DEFF Research Database (Denmark)

    Costagliola, F.; Aalto, S.; I. Rodriguez, M.;

    2011-01-01

    We investigate the molecular gas properties of a sample of 23 galaxies in order to find and test chemical signatures of galaxy evolution and to compare them to IR evolutionary tracers. Observation at 3 mm wavelengths were obtained with the EMIR broadband receiver, mounted on the IRAM 30 m telesco...... detect the molecule in its vibrationally excited state.We find low HNC/HCN line ratios (...

  5. Determination of regional flow by use of intravascular PET tracers: microvascular theory and experimental validation for pig livers

    DEFF Research Database (Denmark)

    Munk, O L; Bass, L; Feng, H

    2003-01-01

    with the standard model in a pig liver study. METHODS: Eight pigs underwent a 5-min dynamic PET study after (15)O-carbon monoxide inhalation. Throughout each experiment, hepatic arterial blood and portal venous blood were sampled, and flow was measured with transit-time flow meters. The hepatic dual...

  6. A new aquifer assessment tool using reactive tracers

    Science.gov (United States)

    McKnight, D.; Smalley, A. L.; Banwart, S. A.; Lerner, D. N.; Thomson, N. R.; Thornton, S. F.; Wilson, R. D.

    2003-04-01

    A major obstacle to making informed decisions about trigger levels for restoration and choosing remediation options is that current Site Investigation (SI) practice fails to make optimal use of available SI techniques resulting in poor value for money in conceptual site models. Often it is simply too expensive to obtain the type of site data required to build the case for natural attenuation, even though this restoration option may be relatively cheaper than a pump-and-treat system. In particular, aquifer property measurement techniques for groundwater transport and reactions are too costly and this results in over-reliance on literature values or model assumptions. This results in overly uncertain predictions of in situ performance and therefore unnecessarily cautious risk assessment and costly remediation strategies. Therefore, cost-effective SI tools that have the capability of producing high quality characterisation data are required. The dipole flow test which circulates groundwater between isolated injection (source) and extraction (sink) chambers within a single borehole has been used successfully by others to delineate heterogeneous hydraulic properties in both highly permeable and fractured rock aquifers. We propose to extend this approach by adding a suite of reactive tracers into a dipole flow field to assess the geochemical properties and biodegradation potential of aquifers. If successful this will provide a method to ascertain site-specific parameters for use in appropriate reactive transport models. The initial phase of this project involves the construction of a laboratory-scale physical model of a dipole probe to investigate the utility of the dipole flow and reactive tracer test (DFRTT) as an aquifer assessment tool. This phase will also serve as the developmental stage between mathematical theory and a host of planned field trials. The development of the laboratory-scale DFRTT including initial scoping calculations, numerical simulation results

  7. Small-molecule PET Tracers for Imaging Proteinopathies.

    Science.gov (United States)

    Mathis, Chester A; Lopresti, Brian J; Ikonomovic, Milos D; Klunk, William E

    2017-09-01

    In this chapter, we provide a review of the challenges and advances in developing successful PET imaging agents for 3 major types of aggregated amyloid proteins: amyloid-beta (Aβ), tau, and alpha-synuclein (α-syn). These 3 amyloids are involved in the pathogenesis of a variety of neurodegenerative diseases, referred to as proteinopathies or proteopathies, that include Alzheimer disease, Lewy body dementias, multiple system atrophy, and frontotemporal dementias, among others. In the Introduction section, we briefly discuss the history of amyloid in neurodegenerative diseases and describe why progress in developing effective imaging agents has been hampered by the failure of crystallography to provide definitive ligand-protein interactions for rational radioligand design efforts. Instead, the field has relied on largely serendipitous, trial-and-error methods to achieve useful and specific PET amyloid imaging tracers for Aβ, tau, and α-syn deposits. Because many of the proteopathies involve more than 1 amyloid protein, it is important to develop selective PET tracers for the different amyloids to help assess the relative contribution of each to total amyloid burden. We use Pittsburgh compound B to illustrate some of the critical steps in developing a potent and selective Aβ PET imaging agent. Other selective Aβ and tau PET imaging compounds have followed similar pathways in their developmental processes. Success for selective α-syn PET imaging agents has not been realized yet, but work is ongoing in multiple laboratories throughout the world. In the tau sections, we provide background regarding 3-repeat (3R) and 4-repeat (4R) tau proteins and how they can affect the binding of tau radioligands in different tauopathies. We review the ongoing efforts to assess the properties of tau ligands, which are useful in 3R, 4R, or combined 3R-4R tauopathies. Finally, we describe in the α-syn sections recent attempts to develop selective tracers to image

  8. Very Massive Tracers and Higher Derivative Biases

    CERN Document Server

    Fujita, Tomohiro; Senatore, Leonardo; Vlah, Zvonimir; Angulo, Raul

    2016-01-01

    Most of the upcoming cosmological information will come from analyzing the clustering of the Large Scale Structures (LSS) of the universe through LSS or CMB observations. It is therefore essential to be able to understand their behavior with exquisite precision. The Effective Field Theory of Large Scale Structures (EFTofLSS) provides a consistent framework to make predictions for LSS observables in the mildly non-linear regime. In this paper we focus on biased tracers. We argue that in calculations at a given order in the dark matter perturbations, highly biased tracers will underperform because of their larger higher derivative biases. A natural prediction of the EFTofLSS is therefore that by simply adding higher derivative biases, all tracers should perform comparably well. We implement this prediction for the halo-halo and the halo-matter power spectra at one loop, and the halo-halo-halo, halo-halo-matter, and halo-matter-matter bispectra at tree-level, and compare with simulations. We find good agreement ...

  9. Carbon monoxide residues in vacuum-packed yellowfin tuna loins (Thunnus Albacares

    Directory of Open Access Journals (Sweden)

    Raffaele Marrone

    2015-09-01

    Full Text Available The use of carbon monoxide (CO in fresh fish has generated considerable debate. Carbon monoxide is used to treat fresh fish in order to retain its fresh red appearance for a longer period. It reacts with the oxy-myoglobin to form a fairly stable cherry red carboxy-myoglobin complex that may mask spoilage, because the CO-complex can be stable beyond the microbiological shelf life of the meat. The presence of CO in tuna fish (Thunnus Albacares has been investigated by means of optical spectroscopy. Formation of the CO adduct can be easily detected by the combined analysis of electronic absorption spectra in their normal and second derivative modes, monitoring the intense Soret band at 420 nm. Samples were judged as CO treated when their levels were higher than 200 ng/g. Only two positive samples out of 29 analyzed were detected. The high level of uncertainty (0.30 of the method requires the use of more specific and sensitive methods for confirmatory analysis.

  10. Carbon Monoxide Residues in Vacuum-Packed Yellowfin Tuna Loins (Thunnus Albacares)

    Science.gov (United States)

    Mascolo, Celestina; Palma, Giuseppe; Smaldone, Giorgio; Girasole, Mariagrazia; Anastasio, Aniello

    2015-01-01

    The use of carbon monoxide (CO) in fresh fish has generated considerable debate. Carbon monoxide is used to treat fresh fish in order to retain its fresh red appearance for a longer period. It reacts with the oxy-myoglobin to form a fairly stable cherry red carboxy-myoglobin complex that may mask spoilage, because the CO-complex can be stable beyond the microbiological shelf life of the meat. The presence of CO in tuna fish (Thunnus Albacares) has been investigated by means of optical spectroscopy. Formation of the CO adduct can be easily detected by the combined analysis of electronic absorption spectra in their normal and second derivative modes, monitoring the intense Soret band at 420 nm. Samples were judged as CO treated when their levels were higher than 200 ng/g. Only two positive samples out of 29 analyzed were detected. The high level of uncertainty (0.30) of the method requires the use of more specific and sensitive methods for confirmatory analysis. PMID:27800404

  11. Quantum cascade laser-based sensors for the detection of exhaled carbon monoxide

    Science.gov (United States)

    Pakmanesh, Nahid; Cristescu, Simona M.; Ghorbanzadeh, Atamalek; Harren, Frans J. M.; Mandon, Julien

    2016-01-01

    Carbon monoxide (CO) is an important biomarker as it originates in the human body from the heme (component of hemoglobin) degradation. Tunable laser absorption spectroscopy in the mid-infrared wavelength region is used for sensitive trace gas sensing of exhaled carbon monoxide (CO). Based on a quantum cascade laser emitting at 4.61 µm, two different spectroscopic methods are investigated: off-axis integrated cavity output spectroscopy (OA-ICOS) and wavelength modulation 2f/1f spectroscopy (WMS). The optical sensors integrate a slow feedback system to correct for wavelength drifts improving their stability over days. Both approaches demonstrate a high reproducibility and sensitivity during online measurements of exhaled human breath. Considering the detection limit to be the equal to the standard deviation of the background fluctuations, the noise-equivalent detection limit for both OA-ICOS and WMS is 7 ppbv (1-s averaging time), leading to a noise-equivalent absorption sensitivity of 3.1 × 10-7 cm-1 Hz-1/2, which is sufficient for measurements of exhaled CO (eCO). Collection and measurements of eCO samples were investigated, and different exhalation flow rates and breath-holding time were explored, to provide a reliable sampling method for future medical investigations.

  12. Flexible tools for interpreting tracer measurements and recent applications

    Science.gov (United States)

    Gusyev, M.; Stewart, M.

    2012-04-01

    Steady increase of groundwater abstraction and nitrate concentrations in groundwater due to agricultural and industrial practices is a major concern for groundwater availability and deterioration of groundwater quality in New Zealand. Studies on groundwater in the Waimea Plains (for example) have shown effects of nitrate input from both diffuse and point sources since 1940. Groundwaters in gravel aquifers under Christchurch have also been studied since 1970 to characterise their flowpaths and recharge sources. In these and other cases, the mixing of waters from different recharge sources following different flow paths can be determined with the use of various tracers and the future course of nitrate concentration in the groundwaters predicted. The input of radionuclides to hydrological systems from nuclear weapons testing in the 1950s and 60s revealed that outflows from such systems often comprise mixtures of water with very wide ranges of ages. Many authors have described methods of deconvolving such outputs with the use of lumped parameter models (LPMs). LPMs are evaluated using specialized software or Excel spreadsheets to compute simulations to measurements of system outputs and therefore estimate parameters of the age distribution. Excel allows easy modification of the code to enable application to individual hydrological features and for a variety of isotopes and chemicals. For the New Zealand studies, Excel spreadsheets with coded Visual Basic functions are used to deduce age distributions based on stable isotope, SF6, CFCs, 3H and 14C data (in order of ages). In particular, 3H is becoming increasingly useful as an age tracer due to the decrease of ambiguity from nuclear testing provided that the measurements can be made with high accuracy (Stewart et al., 2012).These age distributions allow us to derive the input histories of chemicals (e.g. nitrate) and the groundwater recharge sources. In addition, recent developments in modelling groundwater flow and

  13. Digit and letter alexia in carbon monoxide poisoning

    Institute of Scientific and Technical Information of China (English)

    Qingyu Shen; Xiaoming Rong; Rui Pan; Ying Peng; Wei Peng; Yamei Tang

    2012-01-01

    This study examined a 24-year-old patient with delayed encephalopathy, who was admitted to hospital with complaints of headache and visual impairment 1 week after acute carbon monoxide poisoning. The results of a visual field assessment, electroencephalography and head magnetic resonance imaging indicated damage to the cerebral cortex. After a 2-week treatment period, the patient had recovered from the visual impairment, but exhibited digit- and letter-reading difficulty. The Chinese aphasia battery and the number and letter battery supplement were conducted. The results revealed that the patient exhibited digit and letter alexia, while the ability to read Chinese characters was preserved. In contrast, the patient exhibited a deficit in Chinese character writing, while number and letter writing remained intact. Following treatment, reading and writing ability was improved and electroencephalographic abnormalities were ameliorated. Overall, our experimental findings demonstrated that delayed encephalopathy following acute carbon monoxide poisoning was characterized by digit and letter alexia.

  14. Catalysis of carbon monoxide methanation by deep sea manganate minerals

    Science.gov (United States)

    Cabrera, A. L.; Maple, M. B.; Arrhenius, G.

    1990-01-01

    The catalytic activity of deep sea manganese nodule minerals for the methanation of carbon monoxide was measured with a microcatalytic technique between 200 and 460 degrees C. The manganate minerals were activated at 248 degrees C by immersion into a stream of hydrogen in which pulses of carbon monoxide were injected. Activation energies for the methanation reaction and hydrogen desorption from the manganate minerals were obtained and compared with those of pure nickel. Similar energy values indicate that the activity of the nodule materials for the reaction appears to be related to the amount of reducible transition metals present in the samples (ca. 11 wt.-%). Since the activity of the nodule minerals per gram is comparable to that of pure nickel, most of the transition metal ions located between manganese oxide layers appear to be exposed and available to catalyze the reaction.

  15. Effect of carbon monoxide on plants. [Mimosa pudica

    Energy Technology Data Exchange (ETDEWEB)

    Zimmerman, P.W.; Crocker, W.; Hitchcock, A.E.

    1933-01-01

    Of 108 species of plants treated with one per cent carbon monoxide, 45 showed epinastic growth of leaves. Several species showed hyponasty which caused upward curling of leaves. Other effects included: retarded stem elongation; abnormally small new leaves; abnormal yellowing of the leaves, beginning with the oldest; abscission of leaves usually associated with yellowing; and hypertrophied tissues on stems and roots. During recovery an abnormally large number of side shoots arose from latent buds of many species. Motion pictures of Mimosa pudica showed a loss of correlation, normal equilibrium position to gravity, and sensitiveness to contact or heat stimuli; however, the leaves moved about more rapidly than those of controls. Since carbon monoxide causes growth rigor and loss of sensitiveness to external stimuli, it is here considered as an anesthetic.

  16. Asian Tracer Experiment and Atmospheric Modeling (TEAM) Project: Draft Field Work Plan for the Asian Long-Range Tracer Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Allwine, K Jerry; Flaherty, Julia E.

    2007-08-01

    This report provides an experimental plan for a proposed Asian long-range tracer study as part of the international Tracer Experiment and Atmospheric Modeling (TEAM) Project. The TEAM partners are China, Japan, South Korea and the United States. Optimal times of year to conduct the study, meteorological measurements needed, proposed tracer release locations, proposed tracer sampling locations and the proposed durations of tracer releases and subsequent sampling are given. Also given are the activities necessary to prepare for the study and the schedule for completing the preparation activities leading to conducting the actual field operations. This report is intended to provide the TEAM members with the information necessary for planning and conducting the Asian long-range tracer study. The experimental plan is proposed, at this time, to describe the efforts necessary to conduct the Asian long-range tracer study, and the plan will undoubtedly be revised and refined as the planning goes forward over the next year.

  17. Estimating the dark matter halo mass of our Milky Way using dynamical tracers

    Science.gov (United States)

    Wang, Wenting; Han, Jiaxin; Cooper, Andrew P.; Cole, Shaun; Frenk, Carlos; Lowing, Ben

    2015-10-01

    The mass of the dark matter halo of the Milky Way can be estimated by fitting analytical models to the phase-space distribution of dynamical tracers. We test this approach using realistic mock stellar haloes constructed from the Aquarius N-body simulations of dark matter haloes in the Λ cold dark matter cosmology. We extend the standard treatment to include a Navarro-Frenk-White potential and use a maximum likelihood method to recover the parameters describing the simulated haloes from the positions and velocities of their mock halo stars. We find that the estimate of halo mass is highly correlated with the estimate of halo concentration. The best-fitting halo masses within the virial radius, R200, are biased, ranging from a 40 per cent underestimate to a 5 per cent overestimate in the best case (when the tangential velocities of the tracers are included). There are several sources of bias. Deviations from dynamical equilibrium can potentially cause significant bias; deviations from spherical symmetry are relatively less important. Fits to stars at different galactocentric radii can give different mass estimates. By contrast, the model gives good constraints on the mass within the half-mass radius of tracers even when restricted to tracers within 60 kpc. The recovered velocity anisotropies of tracers, β, are biased systematically, but this does not affect other parameters if tangential velocity data are used as constraints.

  18. [Sudden unilateral sensorineural hearing loss after carbon monoxide intoxication].

    Science.gov (United States)

    Michalska-Piechowiak, Teresa; Miarzyńska, Maria; Perlik-Gattner, Irena

    2004-01-01

    A case of unilateral sensorineural hearing loss of the left ear after carbon monoxide intoxication was presented. The diagnosis was based upon an interview, medical examinations and audiometric investigations. Results of diagnostic evaluations, clinical presentation and treatment were discussed. Hearing improvement was obtained after 6 days of treatment and normal hearing returned after 14 days. Patients who suffer from CO intoxication are at risk of hearing impairment, therefore, there is a need for audiometric follow up in these patients.

  19. New approach to carbon monoxide poisoning treatment by laser-induced photodissociation of carboxyhemoglobin of cutaneous blood vessels

    Science.gov (United States)

    Asimov, Mustafo M.; Asimov, Rustam M.; Gisbrecht, Alexander

    2005-04-01

    A new approach to carbon monoxide poisoning treatment based on laser-induced photodissociation of the carboxyhemoglobin is proposed. Using the simple model of laser tissue interaction the action spectra of laser radiation on carboxyhemoglobin of cutaneous blood vessels has been calculated. The results of the calculatoins indicate that there is a relatively narrow spectral range in the visible region where one could effectively irradiate carboxyhemoglobin through the tissue not in a deep distances. In the case of deeper penetration, the action spectra of laser radiation shifts toward the longer wavelength region. Despite the similarity of the carboxyhemoglobin and oxyhemoglobin action spectra, the significant difference in quantum yields of photodissociation makes possible to develop an effective method of carbon monoxide poisoning treatment.

  20. Hydrothermal Synthesis of Pt-, Fe-, and Zn-doped SnO2 Nanospheres and Carbon Monoxide Sensing Properties

    Directory of Open Access Journals (Sweden)

    Weigen Chen

    2013-01-01

    Full Text Available Pure and M-doped (M = Pt, Fe, and Zn SnO2 nanospheres were successfully synthesized via a simple and facile hydrothermal method and characterized by X-ray powder diffraction, field-emission scanning electron microscopy, and energy dispersive spectroscopy. Chemical gas sensors were fabricated based on the as-synthesized nanostructures, and carbon monoxide sensing properties were systematically measured. Compared to pure, Fe-, and Zn-doped SnO2 nanospheres, the Pt-doped SnO2 nanospheres sensor exhibits higher sensitivity, lower operating temperature, more rapid response and recovery, better stability, and excellent selectivity. In addition, a theoretical study based on the first principles calculation was conducted. All results demonstrate the potential of Pt dopant for improving the gas sensing properties of SnO2-based sensors to carbon monoxide.

  1. Mobile Carbon Monoxide Monitoring System Based on Arduino-Matlab for Environmental Monitoring Application

    Science.gov (United States)

    Azieda Mohd Bakri, Nur; Junid, Syed Abdul Mutalib Al; Razak, Abdul Hadi Abdul; Idros, Mohd Faizul Md; Karimi Halim, Abdul

    2015-11-01

    Nowadays, the increasing level of carbon monoxide globally has become a serious environmental issue which has been highlighted in most of the country globally. The monitoring of carbon monoxide content is one of the approaches to identify the level of carbon monoxide pollution towards providing the solution for control the level of carbon monoxide produced. Thus, this paper proposed a mobile carbon monoxide monitoring system for measuring the carbon monoxide content based on Arduino-Matlab General User Interface (GUI). The objective of this project is to design, develop and implement the real-time mobile carbon monoxide sensor system and interfacing for measuring the level of carbon monoxide contamination in real environment. Four phases or stages of work have been carried out for the accomplishment of the project, which classified as sensor development, controlling and integrating sensor, data collection and data analysis. As a result, a complete design and developed system has been verified with the handheld industrial standard carbon monoxide sensor for calibrating the sensor sensitivity and measurement in the laboratory. Moreover, the system has been tested in real environments by measuring the level of carbon monoxide in three different lands used location; industrial area; residential area and main road (commercial area). In this real environment test, the industrial area recorded the highest reading with 71.23 ppm and 82.59 ppm for sensor 1 and sensor 2 respectively. As a conclusion, the mobile realtime carbon monoxide system based on the Arduino-Matlab is the best approach to measure the carbon monoxide concentration in different land-used since it does not require a manual data collection and reduce the complexity of the existing carbon monoxide level concentration measurement practise at the same time with a complete data analysis facilities.

  2. Estimation of Uncertainty in Tracer Gas Measurement of Air Change Rates

    Directory of Open Access Journals (Sweden)

    Atsushi Iizuka

    2010-12-01

    Full Text Available Simple and economical measurement of air change rates can be achieved with a passive-type tracer gas doser and sampler. However, this is made more complex by the fact many buildings are not a single fully mixed zone. This means many measurements are required to obtain information on ventilation conditions. In this study, we evaluated the uncertainty of tracer gas measurement of air change rate in n completely mixed zones. A single measurement with one tracer gas could be used to simply estimate the air change rate when n = 2. Accurate air change rates could not be obtained for n ≥ 2 due to a lack of information. However, the proposed method can be used to estimate an air change rate with an accuracy of

  3. Development of Radon-222 as Natural Tracer for Monitoring the Remediation of NAPL in the Subsurface

    Energy Technology Data Exchange (ETDEWEB)

    Brian M. Davis; Lewis Semprini; Jonathan Istok

    2003-02-27

    Naturally occurring 222-radon in ground water can potentially be used as an in situ partitioning tracer to characterize dense nonaqueous phase liquid (DNAPL) saturations. The static method involves comparing radon concentrations in water samples from DNAPL-contaminated and non-contaminated portions of an aquifer. During a push-pull test, a known volume of test solution (radon-free water containing a conservation tracer) is first injected (''pushed'') into a well; flow is then reversed and the test solution/groundwater mixture is extracted (''pulled'') from the same well. In the presence of NAPL radon transport is retarded relative to the conservative tracer. Assuming linear equilibrium partitioning, retardation factors for radon can be used to estimate NAPL saturations.The utility of this methodology was evaluated in laboratory and field settings.

  4. Enhanced acute anti-inflammatory effects of CORM-2-loaded nanoparticles via sustained carbon monoxide delivery.

    Science.gov (United States)

    Qureshi, Omer Salman; Zeb, Alam; Akram, Muhammad; Kim, Myung-Sic; Kang, Jong-Ho; Kim, Hoo-Seong; Majid, Arshad; Han, Inbo; Chang, Sun-Young; Bae, Ok-Nam; Kim, Jin-Ki

    2016-11-01

    The aim of this study was to enhance the anti-inflammatory effects of carbon monoxide (CO) via sustained release of CO from carbon monoxide-releasing molecule-2-loaded lipid nanoparticles (CORM-2-NPs). CORM-2-NPs were prepared by hot high pressure homogenization method using trilaurin as a solid lipid core and Tween 20/Span 20/Myrj S40 as surfactant mixture. The physicochemical properties of CORM-2-NPs were characterized and CO release from CORM-2-NPs was assessed by myoglobin assay. In vitro anti-inflammatory effects were evaluated by nitric oxide assay in lipopolysaccharide-stimulated RAW 264.7 macrophages. In vivo anti-inflammatory activity was investigated by measuring paw volumes and histological examination in carrageenan-induced rat paw edema. Spherical CORM-2-NPs were around 100nm with narrow particle size distribution. The sustained CO release from CORM-2-NPs was observed and the half-life of CO release increased up to 10 times compared with CORM-2 solution. CORM-2-NPs showed enhanced in vitro anti-inflammatory effects by inhibition of nitric oxide production. Edema volume in rat paw was significantly reduced after treatment with CORM-2-NPs. Taken together, CORM-2-NPs have a great potential for CO therapeutics against inflammation via sustained release of CO. Copyright © 2016 Elsevier B.V. All rights reserved.

  5. Carbon monoxide measurement by gas chromatography; Mesure du monoxyde de carbone par chromatographie en phase gazeuse

    Energy Technology Data Exchange (ETDEWEB)

    Gros, V.; Sarda-Esteve, R.; Bonsang, B.; Ramonet, M.

    1998-09-01

    Although carbon monoxide (CO) is present in trace quantities in the atmosphere (0.1 ppm -or parts per million in volume- on average), the study of this gas is important. Indeed, its impact on human can be dangerous at high level of concentration on the hand and it constitutes one of the main precursor of ozone in presence of concentration on the one hand and it constitutes one of the main precursor of ozone in presence of other pollutants on the other hand. Finally, CO affects the levels of several important greenhouse gases, through its reaction with hydroxyl radicals (OH). CO is measured in the atmosphere since the mid 60's by various methods. Among them, gas chromatography has the advantage to combine a low detection limit with a high precision. This report details the improvements made on the measurement analyser which allowed to perform automatic CO measurements in remote areas with low mixing ratios of carbon monoxide. This report describes some quality tests and the results of various applications. (authors)

  6. CityFlux perfluorocarbon tracer experiments

    Science.gov (United States)

    Petersson, F. K.; Martin, D.; White, I. R.; Henshaw, S. J.; Nickless, G.; Longley, I.; Percival, C. J.; Gallagher, M.; Shallcross, D. E.

    2010-07-01

    In June 2006, two perfluorocarbon tracer experiments were conducted in central Manchester UK as part of the CityFlux campaign. The main aim was to investigate vertical dispersion in an urban area during convective conditions, but dispersion mechanisms within the street network were also studied. Paired receptors were used in most cases where one receptor was located at ground level and one at roof level. One receptor was located on the roof of Portland Tower which is an 80 m high building in central Manchester. Source receptor distances in the two experiments varied between 120 and 600 m. The results reveal that maximum concentration was sometimes found at roof level rather than at ground level implying the effectiveness of convective forces on dispersion. The degree of vertical dispersion was found to be dependent on source receptor distance as well as on building height in proximity to the release site. Evidence of flow channelling in a street canyon was also found. Both a Gaussian profile and a street network model were applied and the results show that the urban topography may lead to highly effective flow channelling which therefore may be a very important dispersion mechanism should the right meteorological conditions prevail. The experimental results from this campaign have also been compared with a simple urban dispersion model that was developed during the DAPPLE framework and show good agreement with this. The results presented here are some of the first published regarding vertical dispersion. More tracer experiments are needed in order to further characterise vertical concentration profiles and their dependence on, for instance, atmospheric stability. The impact of urban topography on pollutant dispersion is important to focus on in future tracer experiments in order to improve performance of models as well as for our understanding of the relationship between air quality and public health.

  7. CityFlux perfluorocarbon tracer experiments

    Directory of Open Access Journals (Sweden)

    F. K. Petersson

    2010-01-01

    Full Text Available In June 2006, two perfluorocarbon tracer experiments were conducted in central Manchester UK as part of the CityFlux campaign. The main aim was to investigate vertical dispersion in an urban area during convective conditions, but dispersion mechanisms within the street network were also studied. Paired receptors were used in most cases where one receptor was located at ground level and one at roof level. One receptor was located on the roof of Portland Tower which is an 80 m high building in central Manchester. Source receptor distances in the two experiments varied between 120 and 600 m.

    The results reveal that maximum concentration was sometimes found at roof level rather than at ground level implying the effectiveness of convective forces on dispersion. The degree of vertical dispersion was found to be dependent on source receptor distance as well as on building height in proximity to the release site.

    Evidence of flow channelling in a street canyon was also found. Both a Gaussian profile and a street network model were applied and the results show that the urban topography may lead to highly effective flow channelling which therefore may be a very important dispersion mechanism should the right meteorological conditions prevail.

    The experimental results from this campaign have also been compared with a simple urban dispersion model that was developed during the DAPPLE framework and show good agreement with this.

    The results presented here are some of the first published regarding vertical dispersion. More tracer experiments are needed in order to further characterise vertical concentration profiles and their dependence on, for instance, atmospheric stability. The impact of urban topography on pollutant dispersion is important to focus on in future tracer experiments in order to improve performance of models as well as for our understanding of the relationship between air quality and public health.

  8. CityFlux perfluorocarbon tracer experiments

    Directory of Open Access Journals (Sweden)

    F. K. Petersson

    2010-07-01

    Full Text Available In June 2006, two perfluorocarbon tracer experiments were conducted in central Manchester UK as part of the CityFlux campaign. The main aim was to investigate vertical dispersion in an urban area during convective conditions, but dispersion mechanisms within the street network were also studied. Paired receptors were used in most cases where one receptor was located at ground level and one at roof level. One receptor was located on the roof of Portland Tower which is an 80 m high building in central Manchester. Source receptor distances in the two experiments varied between 120 and 600 m.

    The results reveal that maximum concentration was sometimes found at roof level rather than at ground level implying the effectiveness of convective forces on dispersion. The degree of vertical dispersion was found to be dependent on source receptor distance as well as on building height in proximity to the release site.

    Evidence of flow channelling in a street canyon was also found. Both a Gaussian profile and a street network model were applied and the results show that the urban topography may lead to highly effective flow channelling which therefore may be a very important dispersion mechanism should the right meteorological conditions prevail.

    The experimental results from this campaign have also been compared with a simple urban dispersion model that was developed during the DAPPLE framework and show good agreement with this.

    The results presented here are some of the first published regarding vertical dispersion. More tracer experiments are needed in order to further characterise vertical concentration profiles and their dependence on, for instance, atmospheric stability. The impact of urban topography on pollutant dispersion is important to focus on in future tracer experiments in order to improve performance of models as well as for our understanding of the relationship between air quality and public health.

  9. Impact of planetary boundary layer turbulence on model climate and tracer transport

    Science.gov (United States)

    McGrath-Spangler, E. L.; Molod, A.; Ott, L. E.; Pawson, S.

    2015-07-01

    Planetary boundary layer (PBL) processes are important for weather, climate, and tracer transport and concentration. One measure of the strength of these processes is the PBL depth. However, no single PBL depth definition exists and several studies have found that the estimated depth can vary substantially based on the definition used. In the Goddard Earth Observing System (GEOS-5) atmospheric general circulation model, the PBL depth is particularly important because it is used to calculate the turbulent length scale that is used in the estimation of turbulent mixing. This study analyzes the impact of using three different PBL depth definitions in this calculation. Two definitions are based on the scalar eddy diffusion coefficient and the third is based on the bulk Richardson number. Over land, the bulk Richardson number definition estimates shallower nocturnal PBLs than the other estimates while over water this definition generally produces deeper PBLs. The near-surface wind velocity, temperature, and specific humidity responses to the change in turbulence are spatially and temporally heterogeneous, resulting in changes to tracer transport and concentrations. Near-surface wind speed increases in the bulk Richardson number experiment cause Saharan dust increases on the order of 1 × 10-4 kg m-2 downwind over the Atlantic Ocean. Carbon monoxide (CO) surface concentrations are modified over Africa during boreal summer, producing differences on the order of 20 ppb, due to the model's treatment of emissions from biomass burning. While differences in carbon dioxide (CO2) are small in the time mean, instantaneous differences are on the order of 10 ppm and these are especially prevalent at high latitude during boreal winter. Understanding the sensitivity of trace gas and aerosol concentration estimates to PBL depth is important for studies seeking to calculate surface fluxes based on near-surface concentrations and for studies projecting future concentrations.

  10. [Studies on percutaneous absorption of ruyi jinhuang san patcher with radioisotope tracer].

    Science.gov (United States)

    Zhao, H W; Shen, Z; Zhou, B; Lin, X; Ye, M

    1993-04-01

    Berberine is one of the active ingredients in Ruyi Jinhuang San Patcher. With 3H-berberine as the tracer, a radio-labelled method was used for determining percutaneous rate and drug concentration of berberine in plasma in vivo and in vitro. A study on the percutaneous rate of different technological plasters and various animal skins was also carried out.

  11. Central Diabetes Insipidus and Hyperglycemic Hyperosmolar State Following Accidental Carbon Monoxide Poisoning.

    Science.gov (United States)

    Ul Abideen, Zain; Mahmud, Syed Nayer; Rasheed, Amna; Farooq Qasim, Yusaf; Ali, Furqan

    2017-06-03

    Carbon monoxide poisoning is common and carries significant morbidity and mortality. The nervous system, particularly the brain, is frequently affected by it, owing to its high metabolic activity and oxygen requirements. Carbon monoxide damages the nervous system by both hypoxic and inflammatory mechanisms. Central diabetes insipidus is an extremely rare complication of carbon monoxide poisoning. Herein, we report the case of a young lady, who developed this complication and severe hypernatremia after accidental carbon monoxide poisoning. She also developed a hyperglycemic hyperosmolar state during the treatment for hypernatremia. To the best of our knowledge, both these entities have not been reported together in association with carbon monoxide poisoning. The purpose of this article is to emphasize the anticipation and early recognition of central diabetes insipidus in carbon monoxide poisoning. This can prevent severe hypernatremia and complications associated with its presence and treatment.

  12. Detection of tracer materials in the atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Jenkins, A.; Lovelock, J.E.

    1981-12-08

    As oxygen is an electron absorber it is desirable, when monitoring an atmospheric flow for the presence of tracer materials capable of detection in an electron capture detector, to remove the oxygen from the flow to the detector. The invention introduces a hydrogen supply directly into the atmospheric flow to allow the hydrogen to combine catalytically with the oxygen content of the flow to form water or water vapor. The thus formed water or water vapor is extracted from the flow proceeding to the detector. The reaction can occur within a palladium or palladium alloy conduit forming a part of the flow path to the detector.

  13. Tracer Dispersion in a Multi-compartment Structure

    CERN Document Server

    Skvortsov, A; Gamble, G; Roberts, M; Ilaya, O; Pitaliadda, D

    2012-01-01

    An experimental study of the tracer dispersion in a complex structure is presented. A point source of tracer (dyed salt) was placed inside a multi-compartment structure embedded in water tank. This experimental setting corresponds to a hazardous tracer release inside the engineering structure (building, ship, aircarft etc). A system of conductivity sensors was deployed to monitor the propagation of a tracer plume in the structure, including tracer trapping inside some compartments and its release to the outside environment through the external openings. The experimental data is processed by employing the ideas of scaling and self-similarity of underlying transport processes. The established and validated scaling laws provide a rigorous way to up-scale the results of laboratory modeling to real operational scenarios and can be used as an important step in the development of risk-assessment models for the first responders to hazardous releases. Keywords: hazardous plume, tracer dispersion, diffusion and advecti...

  14. Carbon monoxide and respiratory symptoms in young adult passive smokers: A pilot study comparing waterpipe to cigarette

    Directory of Open Access Journals (Sweden)

    Rouba Zeidan

    2014-08-01

    Full Text Available Objectives: Studies have correlated second hand smoke (SHS with many diseases, especially respiratory effects. The goal of this study was to measure the impact of SHS on the respiratory symptoms and exhaled carbon monoxide. Material and Methods: The study population consisted of 50 young workers in restaurants serving waterpipes, 48 university students who sit frequently in the university cafeteria where cigarette smoking is allowed and 49 university students spending time in places where smoking is not allowed. Subjects completed questionnaires on socio-demographic characteristics, respiratory symptoms and exposure to SHS. Exhaled carbon monoxide levels were measured. ANOVA and Chi-square tests were used when applicable as well as linear and logistic regression analysis. Results: Exposure to cigarette smoke in university (adjusted odds ratio (ORa = 6.06 and occupational exposure to waterpipe smoke (ORa = 7.08 were predictors of chronic cough. Being married (ORa = 6.40, living near a heavy traffic road (ORa = 9.49 or near a local power generator (ORa = 7.54 appeared responsible for chronic sputum production. Moreover, predictors of chronic allergies were: being male (ORa = 7.81, living near a local power generator (ORa = 5.52 and having a family history of chronic respiratory diseases (ORa = 17.01. Carbon monoxide levels were augmented by the number of weekly hours of occupational exposure to waterpipe smoke (β = 1.46 and the number of daily hours of exposure to cigarette smoke (β = 1.14. Conclusions: In summary, young non-smoker subjects demonstrated more chronic cough and elevated carbon monoxide levels when exposed to SHS while the effect of waterpipe was even more evident.

  15. Gold catalysts supported on nanosized iron oxide for low-temperature oxidation of carbon monoxide and formaldehyde

    Science.gov (United States)

    Tang, Zheng; Zhang, Weidong; Li, Yi; Huang, Zuming; Guo, Huishan; Wu, Feng; Li, Jinjun

    2016-02-01

    This study aimed to optimize synthesis of gold catalyst supported on nanosized iron oxide and to evaluate the activity in oxidation of carbon monoxide and formaldehyde. Nanosized iron oxide was prepared from a colloidal dispersion of hydrous iron oxide through a dispersion-precipitation method. Gold was adsorbed onto nanosized iron oxide under self-generated basic conditions. Characterization results indicate that the iron oxide consisted of hematite/maghemite composite with primary particle sizes of 6-8 nm. Gold was highly dispersed on the surface of the support. The catalysts showed good activity in the oxidation of airborne carbon monoxide and formaldehyde. The optimal pH for their synthesis was ∼7. The catalytic performance could be enhanced by extending the adsorption time of gold species on the support within 21 h. The optimized catalyst was capable of achieving complete oxidation of 1% carbon monoxide at -20 °C and 33% conversion of 450 ppm formaldehyde at ambient temperature. The catalyst may be applicable to indoor air purification.

  16. A cross-sectional study of exhaled carbon monoxide as a biomarker of recent household air pollution exposure.

    Science.gov (United States)

    Lee, Alison; Sanchez, Tiffany R; Shahriar, Muhammad Hasan; Eunus, Mahbubul; Perzanowski, Matthew; Graziano, Joseph

    2015-11-01

    Household air pollution causes 3.5 million deaths annually. Personal exposure assessments required for examining health associations are expensive and require technical expertize, limiting the quality of research in resource-poor settings To assess the feasibility of exhaled carbon monoxide and its relationship to continuous personal carbon monoxide monitoring and markers of respiratory health in female cooks primarily cooking with biomass fuels in Araihazar, Bangladesh METHODS AND MEASURE: For a 24-h period, exhaled carboxyhemoglobin (eCOHb) % saturation was measured before and after each cooking episode while simultaneous 24-h personal carbon monoxide monitoring was conducted. The Coburn-Forester-Kane (CFK) equation was used to convert continuous personal CO exposures to predicted COHb % saturation. Respiratory symptoms were assessed by St. George's Respiratory Questionnaire, airway inflammation measured by exhaled breath condensate pH, and lung function determined by spirometry. Spearman's correlation was used to examine the relationship between eCOHb and CKF-derived COHb, EBC pH, and lung function variables. eCOHb % saturation was dichotomized around the median and odds ratios calculated for each respiratory symptom Measurement of eCOHb % saturation is feasible in a resource-poor setting. eCOHb % saturation responds to cooking episodes and demonstrates consistency when measured at the same time point 24-h later, suggesting that eCOHb may be a sensitive biomarker of recent HAP exposures. Copyright © 2015 Elsevier Inc. All rights reserved.

  17. Serum bilirubin value predicts hospital admission in carbon monoxide-poisoned patients. Active player or simple bystander?

    Directory of Open Access Journals (Sweden)

    Gianfranco Cervellin

    Full Text Available OBJECTIVES: Although carbon monoxide poisoning is a major medical emergency, the armamentarium of recognized prognostic biomarkers displays unsatisfactory diagnostic performance for predicting cumulative endpoints. METHODS: We performed a retrospective and observational study to identify all patients admitted for carbon monoxide poisoning during a 2-year period. Complete demographical and clinical information, along with the laboratory data regarding arterial carboxyhemoglobin, hemoglobin, blood lactate and total serum bilirubin, was retrieved. RESULTS: The study population consisted of 38 poisoned patients (23 females and 15 males; mean age 39±21 years. Compared with discharged subjects, hospitalized patients displayed significantly higher values for blood lactate and total serum bilirubin, whereas arterial carboxyhemoglobin and hemoglobin did not differ. In a univariate analysis, hospitalization was significantly associated with blood lactate and total serum bilirubin, but not with age, sex, hemoglobin or carboxyhemoglobin. The diagnostic performance obtained after combining the blood lactate and total serum bilirubin results (area under the curve, 0.90; 95% CI, 0.81-0.99; p<0.001 was better than that obtained for either parameter alone. CONCLUSION: Although it remains unclear whether total serum bilirubin acts as an active player or a bystander, we conclude that the systematic assessment of bilirubin may, alongside lactate levels, provide useful information for clinical decision making regarding carbon monoxide poisoning.

  18. Carbon monoxide may be an important molecule in migraine and other headaches

    DEFF Research Database (Denmark)

    Arngrim, Nanna; Schytz, Henrik W; Hauge, Mette K

    2014-01-01

    INTRODUCTION: Carbon monoxide was previously considered to just be a toxic gas. A wealth of recent information has, however, shown that it is also an important endogenously produced signalling molecule involved in multiple biological processes. Endogenously produced carbon monoxide may thus play...... an important role in nociceptive processing and in regulation of cerebral arterial tone. DISCUSSION: Carbon monoxide-induced headache shares many characteristics with migraine and other headaches. The mechanisms whereby carbon monoxide causes headache may include hypoxia, nitric oxide signalling and activation...

  19. Thermal degradation kinetics of polyketone based on styrene and carbon monoxide

    Energy Technology Data Exchange (ETDEWEB)

    Mu, Jiali, E-mail: jiaqm411@163.com; Fan, Wenjun; Shan, Shaoyun; Su, Hongying; Wu, Shuisheng; Jia, Qingming

    2014-03-01

    Highlights: • The PK were synthesized from carbon monoxide and styrene in the presence of PANI-PdCl{sub 2} catalyst and PdCl{sub 2} catalyst. • The structures and thermal behaviors of PK prepared by homogenous and the supported catalyst were investigated. • The microstructures of PK were changed in the supported catalyst system. • The alternating PK copolymer (PANI-PdCl{sub 2} catalyst) was more thermally stable than PK (PdCl{sub 2} catalyst). • The degradation activation energy values were estimated by Flynn–Wall–Ozawa method and Kissinger method. - Abstract: Copolymerization of styrene with carbon monoxide to give polyketones (PK) was carried out under homogeneous palladium catalyst and polyaniline (PANI) supported palladium(II) catalyst, respectively. The copolymers were characterized by {sup 1}H NMR, {sup 13}C NMR and GPC. The results indicated that the PK catalyzed by the supported catalyst has narrow molecular weight distribution (PDI = 1.18). For comparison purpose of thermal behaviors of PK prepared by the homogeneous and the supported catalyst, thermogravimetric (TG) analysis and derivative thermogravimetric (DTG) were conducted at different heating rates. The peak temperatures (396–402 °C) for PK prepared by the supported catalyst are higher than those (387–395 °C) of PK prepared by the homogeneous catalyst. The degradation activation energy (E{sub k}) values were estimated by Flynn–Wall–Ozawa method and Kissinger method, respectively. The E{sub k} values, as determined by two methods, were found to be in the range 270.72 ± 0.03–297.55 ± 0.10 kJ mol{sup −1}. Structures analysis and thermal degradation analysis revealed that the supported catalyst changed the microstructures of PK, resulting in improving thermal stability of PK.

  20. Preparation of Plant 41Ca Tracer Samples for Accelerator Mass Spectrometry

    Directory of Open Access Journals (Sweden)

    ZHAO Qing-zhang1;JANG Ping-ping3;LIN De-yu4;YANG Xian-lin1;DOU Liang1;PANG Yi-jun1;WANG Xiao-ming1;ZHANG Hui1,5;YANG Xu-ran1;WU Shao-yong1;GAO Dong-sheng2;LI Ling2;WANG Lei2;SUN Ke-peng2;ZHOU Jun2;DONG Ke-jun1;HE Ming1

    2016-11-01

    Full Text Available Calcium plays an important role in the metabolism of plants and animals. In this paper, the preparation method of plant 41Ca for accelerator mass spectrometry (AMS measurement was developed for the first time in China. AMS, with its advantages of high sensitivity, small dose of radioactivity, high accuracy, large measuring range, and long tracer cycle, can be used to measure cosmogenic nuclide 41Ca , which has long half-life. The intensity of the beam in ion source is an important parameter for the sensitivity of AMS measurement. The high beam current can improve the sensitivity of AMS. The preparation methods of plant samples of 41Ca tracer were systematically studied to obtain high beam current using wet, dry and a combining method with wet and dry re-fluoride. A reliable preparation procedure of plant samples for 41Ca tracer and its optimization parameters were determined by testing beam currents of various samples and lay a foundation for the 41Ca-AMS technology at plant tracer applications.

  1. Use of tracers for mud filtrate and completion fluid invasion studies

    Energy Technology Data Exchange (ETDEWEB)

    Kleven, Reidun [Statoil DDB, Bergen (Norway); Dahl, John Blessum; Bjoernstad, Tor; Qvenild, Carsten; Tollan, Odd [Institutt for energiteknikk, Kjeller (Norway)

    1996-09-30

    The objectives of this work are (1): to study sorption/desorption of mud filtrate ions near the wellbore region by using water sampled with a formation tester equipment (FTE); (2) to study sorption/desorption of ions in the mud filtrate and the completion fluid by monitoring the ionic composition of produced water; (3) to determine the fraction of mud filtrate and completion fluid water in produced water; and (4) develop a suitable and safe tracer method. A tracer method was developed to measure sorption/desorption of various ions infiltrating the reservoir during drilling and completion of a well. Tritiated water (HTO) was used to tag the mud filtrate and bromide ion (Br{sup -}) to tag the completion fluid. The measurements are based on analysis of FTE and produced water samples. The ionic concentrations observed are compared with corresponding `no sorption/desorption` concentration values determined theoretically. Special attention is paid to the `tracer diagram` of an open well, because a `no sorption/desorption curve` can be expressed in a straight line in a linear coordinate system. Observed deviations from these curves show that sorption/desorption processes have taken place. The tracer method presented was useful to determine the distribution of ions in the pore-water/sedimentary rock system near the wellbore

  2. Estimation of longitudinal and transverse dispersivities in the Twin Lake natural gradient tracer tests

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Seiji [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Moltyaner, G.L.

    1998-06-01

    The field scale tracer tests were carried out with a non-reactive tracer of {sup 131}I at Twin Lake on the Chalk River Laboratory (CRL) site in Atomic Energy of Canada Limited (AECL). The natural gradient dispersion test such as the Twin Lake tracer test is very few and useful for evaluating mass transport parameters and testing groundwater flow and transport models. In this report, mass transport parameters, velocity, longitudinal and transverse dispersivities, were estimated from the Twin Lake 40 m tracer tests. This estimation was performed to provide dispersion data for 3-D transport modelling in the Lake 233 site scale (600 m in east-west direction and 1400 m in north-south direction). Two different methods were applied to the measured breakthrough curves of {sup 131}I in order to evaluate velocity and longitudinal dispersivity. The first method is the fitting procedure of the 1-D advection-dispersion solution, and the second one is the temporal moments analysis. The effect of applying these methods to field data on transport parameters was discussed in this study. The vertical profiles of {sup 131}I were used in the estimation of transverse dispersivity by fitting the 3-D advection-dispersion solution. This report refereed to the effect of variable velocity on the estimated dispersivities. The correlation between magnitude of both dispersivities and the travel distance up to 40 m was also investigated. (author)

  3. Performance Testing of Tracer Gas and Tracer Aerosol Detectors for use in Radionuclide NESHAP Compliance Testing

    Energy Technology Data Exchange (ETDEWEB)

    Fuehne, David Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lattin, Rebecca Renee [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-06-28

    The Rad-NESHAP program, part of the Air Quality Compliance team of LANL’s Compliance Programs group (EPC-CP), and the Radiation Instrumentation & Calibration team, part of the Radiation Protection Services group (RP-SVS), frequently partner on issues relating to characterizing air flow streams. This memo documents the most recent example of this partnership, involving performance testing of sulfur hexafluoride detectors for use in stack gas mixing tests. Additionally, members of the Rad-NESHAP program performed a functional trending test on a pair of optical particle counters, comparing results from a non-calibrated instrument to a calibrated instrument. Prior to commissioning a new stack sampling system, the ANSI Standard for stack sampling requires that the stack sample location must meet several criteria, including uniformity of tracer gas and aerosol mixing in the air stream. For these mix tests, tracer media (sulfur hexafluoride gas or liquid oil aerosol particles) are injected into the stack air stream and the resulting air concentrations are measured across the plane of the stack at the proposed sampling location. The coefficient of variation of these media concentrations must be under 20% when evaluated over the central 2/3 area of the stack or duct. The instruments which measure these air concentrations must be tested prior to the stack tests in order to ensure their linear response to varying air concentrations of either tracer gas or tracer aerosol. The instruments used in tracer gas and aerosol mix testing cannot be calibrated by the LANL Standards and Calibration Laboratory, so they would normally be sent off-site for factory calibration by the vendor. Operational requirements can prevent formal factory calibration of some instruments after they have been used in hazardous settings, e.g., within a radiological facility with potential airborne contamination. The performance tests described in this document are intended to demonstrate the reliable

  4. Extracting a respiratory signal from raw dynamic PET data that contain tracer kinetics

    Science.gov (United States)

    Schleyer, P. J.; Thielemans, K.; Marsden, P. K.

    2014-08-01

    Data driven gating (DDG) methods provide an alternative to hardware based respiratory gating for PET imaging. Several existing DDG approaches obtain a respiratory signal by observing the change in PET-counts within specific regions of acquired PET data. Currently, these methods do not allow for tracer kinetics which can interfere with the respiratory signal and introduce error. In this work, we produced a DDG method for dynamic PET studies that exhibit tracer kinetics. Our method is based on an existing approach that uses frequency-domain analysis to locate regions within raw PET data that are subject to respiratory motion. In the new approach, an optimised non-stationary short-time Fourier transform was used to create a time-varying 4D map of motion affected regions. Additional processing was required to ensure that the relationship between the sign of the respiratory signal and the physical direction of movement remained consistent for each temporal segment of the 4D map. The change in PET-counts within the 4D map during the PET acquisition was then used to generate a respiratory curve. Using 26 min dynamic cardiac NH3 PET acquisitions which included a hardware derived respiratory measurement, we show that tracer kinetics can severely degrade the respiratory signal generated by the original DDG method. In some cases, the transition of tracer from the liver to the lungs caused the respiratory signal to invert. The new approach successfully compensated for tracer kinetics and improved the correlation between the data-driven and hardware based signals. On average, good correlation was maintained throughout the PET acquisitions.

  5. How to chase a tracer - combining conventional salt tracer testing and direct push electrical conductivity profiling for enhanced aquifer characterization

    Science.gov (United States)

    Vienken, Thomas; Huber, Emanuel; Kreck, Manuel; Huggenberger, Peter; Dietrich, Peter

    2017-01-01

    Tracer testing is a well-established technique in hydrogeological site characterization. However, certain a priori knowledge of the hydraulic regime is required beforehand to avoid test failure, e.g. miss of tracer. In this study, we propose a novel tracer test concept for the hydraulic characterization of shallow unconsolidated sedimentary deposits when only scarce a priori information on the hydraulic regime is available. Therefore, we combine conventional salt tracer testing with direct push vertical high resolution electrical conductivity logging. The proposed tracer test concept was successfully tested on coarse, braided river deposits of the Tagliamento River, Italy. With limited a priori information available two tracer tests were performed in three days to reliably determine ground water flow direction and velocity allowing on-site decision-making to adaptively install observation wells for reliable breakthrough curve measurements. Furthermore, direct push vertical electrical profiling provided essential information about the plume characteristics with outstanding measurement resolution and efficiency.

  6. Carbon Monoxide Intensity Mapping at Moderate Redshifts

    CERN Document Server

    Breysse, Patrick C; Kamionkowski, Marc

    2014-01-01

    We present a study of the feasibility of an intensity-mapping survey targeting the 115 GHz CO(1-0) rotational transition at $z\\sim3$. We consider four possible models and estimate the spatial and angular power spectra of CO fluctuations predicted by each of them. The frequency bandwidths of most proposed CO intensity mapping spectrographs are too small to use the Limber approximation to calculate the angular power spectrum, so we present an alternative method for calculating the angular power spectrum. The models we consider span two orders of magnitude in signal amplitude, so there is a significant amount of uncertainty in the theoretical predictions of this signal. We then consider a parameterized set of hypothetical spectrographs designed to measure this power spectrum and predict the signal-to-noise ratios expected under these models. With the spectrographs we consider we find that three of the four models give an SNR greater than 10 within one year of observation. We also study the effects on SNR of vary...

  7. A Real-Time Monitoring System of Industry Carbon Monoxide Based on Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Jiachen Yang

    2015-11-01

    Full Text Available Carbon monoxide (CO burns or explodes at over-standard concentration. Hence, in this paper, a Wifi-based, real-time monitoring of a CO system is proposed for application in the construction industry, in which a sensor measuring node is designed by low-frequency modulation method to acquire CO concentration reliably, and a digital filtering method is adopted for noise filtering. According to the triangulation, the Wifi network is constructed to transmit information and determine the position of nodes. The measured data are displayed on a computer or smart phone by a graphical interface. The experiment shows that the monitoring system obtains excellent accuracy and stability in long-term continuous monitoring.

  8. Carbon monoxide analysis: a comparison of two co-oximeters and headspace gas chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Costantino, A.G.; Park, J.; Caplan, Y.H.

    Three methods (lL-182 Co-Oximeter, lL-282 Co-Oximeter, and headspace gas chromatography) for the analysis of carbon monoxide in postmortem blood were studied and compared using a prepared reference standard, Quantra control materials, and 62 postmortem blood specimens. The methods compared favorably with one another. The linear regression equations for the 62 postmortem blood samples (range = 1.0 to 86% saturation) were: lL-282 vs. lL-182, y = 1.11x - 3.10, r = 0.981; lL-182 vs. GC, y = 0.88x + 2.97, r = 0.973; lL-282 vs. GC, y = 1.00x - 1.24, r = 0.986.

  9. Density function theory study of the adsorption and dissociation of carbon monoxide on tungsten nanoparticles.

    Science.gov (United States)

    Weng, Meng-Hsiung; Ju, Shin-Pon; Chen, Hsin-Tsung; Chen, Hui-Lung; Lu, Jian-Ming; Lin, Ken-Huang; Lin, Jenn-Sen; Hsieh, Jin-Yuan; Yang, Hsi-Wen

    2013-02-01

    The adsorption and dissociation properties of carbon monoxide (CO) molecule on tungsten W(n) (n = 10-15) nanoparticles have been investigated by density-functional theory (DFT) calculations. The lowest-energy structures for W(n) (n = 10-15) nanoparticles are found by the basin-hopping method and big-bang method with the modified tight-binding many-body potential. We calculated the corresponding adsorption energies, C-O bond lengths and dissociation barriers for adsorption of CO on nanoparticles. The electronic properties of CO on nanoparticles are studied by the analysis of density of state and charge density. The characteristic of CO on W(n) nanoparticles are also compared with that of W bulk.

  10. A Real-Time Monitoring System of Industry Carbon Monoxide Based on Wireless Sensor Networks.

    Science.gov (United States)

    Yang, Jiachen; Zhou, Jianxiong; Lv, Zhihan; Wei, Wei; Song, Houbing

    2015-11-20

    Carbon monoxide (CO) burns or explodes at over-standard concentration. Hence, in this paper, a Wifi-based, real-time monitoring of a CO system is proposed for application in the construction industry, in which a sensor measuring node is designed by low-frequency modulation method to acquire CO concentration reliably, and a digital filtering method is adopted for noise filtering. According to the triangulation, the Wifi network is constructed to transmit information and determine the position of nodes. The measured data are displayed on a computer or smart phone by a graphical interface. The experiment shows that the monitoring system obtains excellent accuracy and stability in long-term continuous monitoring.

  11. Deliberate Tracer Injections of Sulfur Hexafluoride on the West Florida Shelf in Support of: An AUV-based Investigation of the Role of Nutrient Variability in the Predictive Modeling of Physical Processes in the Littoral Ocean

    Science.gov (United States)

    2001-09-30

    hexafluoride and it includes development of sampling methods to characterize the tracer field with high spatial and temporal resolution in near real...tracer in essence "freezes" the processes under investigation in space in this dynamic shelf region. APROACH A cruise was performed on the...hexafluoride and it includes development of sampling methods to characterize the tracer field with high spatial and temporal resolution in near real-time

  12. Mixing ratios of carbon monoxide in the troposphere

    Energy Technology Data Exchange (ETDEWEB)

    Novelli, P.C.; Steele, L.P. (Univ. of Colorado, Boulder (United States)); Tans, P.P. (NOAA, Boulder, CO (United States))

    1992-12-20

    Carbon monoxide (CO) mixing ratios were measured in air samples collected weekly at eight locations. The air was collected as part of the CMDL/NOAA cooperative flask sampling program (Climate Monitoring and Diagnostics Laboratory, formerly Geophysical Monitoring for Climatic Change, Air Resources Laboratory/National Oceanic and Atmospheric Administration) at Point Barrow, Alaska, Niwot Ridge, Colorado, Mauna Loa and Cape Kumakahi, Hawaii, Guam, Marianas Islands, Christmas Island, Ascension Island and American Samoa. Half-liter or 3-L glass flasks fitted with glass piston stopcocks holding teflon O rings were used for sample collection. CO levels were determined within several weeks of collection using gas chromatography followed by mercuric oxide reduction detection, and mixing ratios were referenced against the CMDL/NOAA carbon monoxide standard scale. During the period of study (mid-1988 through December 1990) CO levels were greatest in the high latitudes of the northern hemisphere (mean mixing ratio from January 1989 to December 1990 at Point Barrow was approximately 154 ppb) and decreased towards the south (mean mixing ratio at Samoa over a similar period was 65 ppb). Mixing ratios varied seasonally, the amplitude of the seasonal cycle was greatest in the north and decreased to the south. Carbon monoxide levels were affected by both local and regional scale processes. The difference in CO levels between northern and southern latitudes also varied seasonally. The greatest difference in CO mixing ratios between Barrow and Samoa was observed during the northern winter (about 150 ppb). The smallest difference, 40 ppb, occurred during the austral winter. The annually averaged CO difference between 71[degrees]N and 14[degrees]S was approximately 90 ppb in both 1989 and 1990; the annually averaged interhemispheric gradient from 71[degrees]N to 41[degrees]S is estimated as approximately 95 ppb. 66 refs., 5 figs., 5 tabs.

  13. Reintegration of child soldiers in Burundi: a tracer study

    Directory of Open Access Journals (Sweden)

    Jordans Mark JD

    2012-10-01

    Full Text Available Abstract Background Substantial attention and resources are aimed at the reintegration of child soldiers, yet rigorous evaluations are rare. Methods This tracer study was conducted among former child soldiers (N=452 and never-recruited peers (N=191 who participated in an economic support program in Burundi. Socio-economic outcome indicators were measured retrospectively for the period before receiving support (T1; 2005–06; immediately afterwards (T2; 2006–07; and at present (T3; 2010. Participants also rated present functional impairment and mental health indicators. Results Participants reported improvement on all indicators, especially economic opportunity and social integration. At present no difference existed between both groups on any of the outcome indicators. Socio-economic functioning was negatively related with depression- and, health complaints and positively with intervention satisfaction. Conclusion The present study demonstrates promising reintegration trajectories of former child soldiers after participating in a support program.

  14. Reintegration of child soldiers in Burundi: a tracer study

    Science.gov (United States)

    2012-01-01

    Background Substantial attention and resources are aimed at the reintegration of child soldiers, yet rigorous evaluations are rare. Methods This tracer study was conducted among former child soldiers (N=452) and never-recruited peers (N=191) who participated in an economic support program in Burundi. Socio-economic outcome indicators were measured retrospectively for the period before receiving support (T1; 2005–06); immediately afterwards (T2; 2006–07); and at present (T3; 2010). Participants also rated present functional impairment and mental health indicators. Results Participants reported improvement on all indicators, especially economic opportunity and social integration. At present no difference existed between both groups on any of the outcome indicators. Socio-economic functioning was negatively related with depression- and, health complaints and positively with intervention satisfaction. Conclusion The present study demonstrates promising reintegration trajectories of former child soldiers after participating in a support program. PMID:23095403

  15. Quantitative observation of tracer transport with high-resolution PET

    Science.gov (United States)

    Kulenkampff, Johannes; Gruendig, Marion; Zakhnini, Abdelhamid; Lippmann-Pipke, Johanna

    2016-04-01

    Transport processes in natural porous media are typically heterogeneous over various scales. This heterogeneity is caused by the complexity of pore geometry and molecular processes. Heterogeneous processes, like diffusive transport, conservative advective transport, mixing and reactive transport, can be observed and quantified with quantitative tomography of tracer transport patterns. Positron Emission Tomography (PET) is by far the most sensitive method and perfectly selective for positron-emitting radiotracers, therefore it is suited as reference method for spatiotemporal tracer transport observations. The number of such PET-applications is steadily increasing. However, many applications are afflicted by the low spatial resolution (3 - 5 mm) of the clinical scanners from cooperating nuclear medical departments. This resolution is low in relation to typical sample dimensions of 10 cm, which are restricted by the mass attenuation of the material. In contrast, our GeoPET-method applies a high-resolution scanner with a resolution of 1 mm, which is the physical limit of the method and which is more appropriate for samples of the size of soil columns or drill cores. This higher resolution is achieved at the cost of a more elaborate image reconstruction procedure, especially considering the effects of Compton scatter. The result of the quantitative image reconstruction procedure is a suite of frames of the quantitative tracer distribution with adjustable frame rates from minutes to months. The voxel size has to be considered as reference volume of the tracer concentration. This continuous variable includes contributions from structures far below the spatial resolution, as far as a detection threshold, in the pico-molar range, is exceeded. Examples from a period of almost 10 years (Kulenkampff et al. 2008a, Kulenkampff et al. 2008b) of development and application of quantitative GeoPET-process tomography are shown. These examples include different transport processes

  16. Evaluation of Parameter Uncertainty Reduction in Groundwater Flow Modeling Using Multiple Environmental Tracers

    Science.gov (United States)

    Arnold, B. W.; Gardner, P.

    2013-12-01

    Calibration of groundwater flow models for the purpose of evaluating flow and aquifer heterogeneity typically uses observations of hydraulic head in wells and appropriate boundary conditions. Environmental tracers have a wide variety of decay rates and input signals in recharge, resulting in a potentially broad source of additional information to constrain flow rates and heterogeneity. A numerical study was conducted to evaluate the reduction in uncertainty during model calibration using observations of various environmental tracers and combinations of tracers. A synthetic data set was constructed by simulating steady groundwater flow and transient tracer transport in a high-resolution, 2-D aquifer with heterogeneous permeability and porosity using the PFLOTRAN software code. Data on pressure and tracer concentration were extracted at well locations and then used as observations for automated calibration of a flow and transport model using the pilot point method and the PEST code. Optimization runs were performed to estimate parameter values of permeability at 30 pilot points in the model domain for cases using 42 observations of: 1) pressure, 2) pressure and CFC11 concentrations, 3) pressure and Ar-39 concentrations, and 4) pressure, CFC11, Ar-39, tritium, and He-3 concentrations. Results show significantly lower uncertainty, as indicated by the 95% linear confidence intervals, in permeability values at the pilot points for cases including observations of environmental tracer concentrations. The average linear uncertainty range for permeability at the pilot points using pressure observations alone is 4.6 orders of magnitude, using pressure and CFC11 concentrations is 1.6 orders of magnitude, using pressure and Ar-39 concentrations is 0.9 order of magnitude, and using pressure, CFC11, Ar-39, tritium, and He-3 concentrations is 1.0 order of magnitude. Data on Ar-39 concentrations result in the greatest parameter uncertainty reduction because its half-life of 269

  17. Thermal Degradation of Lead Monoxide Filled Polymer Composite Radiation Shields

    Science.gov (United States)

    Harish, V.; Nagaiah, N.

    2011-07-01

    Lead monoxide filled Isophthalate resin particulate polymer composites were prepared with different filler concentrations and investigated for physical, thermal, mechanical and gamma radiation shielding characteristics. This paper discusses about the thermo gravimetric analysis of the composites done to understand their thermal properties especially the effect of filler concentration on the thermal stability & degradation rate of composites. Pristine polymer exhibits single stage degradation whereas filled composites exhibit two stage degradation processes. Further, the IDT values as well as degradation rates decrease with the increased filler content in the composite.

  18. Modeling of Carbon Monoxide Removal by Corona Plasma

    Institute of Scientific and Technical Information of China (English)

    FENG Jingwei; SUN Yabing; ZHAO Dayong; ZHENG Zheng; XU Yuewu; YANG Haifeng; ZHU Hongbiao; ZHOU Xiaoxia

    2009-01-01

    Modeling of carbon monoxide (CO) removal by a corona plasma was conducted in this study.The purification efficiency of CO was calculated theoretically and the factors affecting the removal of CO were analyzed.The results showed that the main removal mechanisms of CO were direct dissociation by generated high-energy electrons and indirect oxidation by generated hydroxyl radicals.The purification efficiency of CO was dependent on the plasma parameters,indoor air humidity and initial concentration of CO.Good consistency between the theoretical calculation and the experimental results was observed.

  19. Pathways and Bioenergetics of Anaerobic Carbon Monoxide Fermentation.

    Science.gov (United States)

    Diender, Martijn; Stams, Alfons J M; Sousa, Diana Z

    2015-01-01

    Carbon monoxide can act as a substrate for different modes of fermentative anaerobic metabolism. The trait of utilizing CO is spread among a diverse group of microorganisms, including members of bacteria as well as archaea. Over the last decade this metabolism has gained interest due to the potential of converting CO-rich gas, such as synthesis gas, into bio-based products. Three main types of fermentative CO metabolism can be distinguished: hydrogenogenesis, methanogenesis, and acetogenesis, generating hydrogen, methane and acetate, respectively. Here, we review the current knowledge on these three variants of microbial CO metabolism with an emphasis on the potential enzymatic routes and bio-energetics involved.

  20. Pathways and bioenergetics of anaerobic carbon monoxide fermentation.

    Directory of Open Access Journals (Sweden)

    Martijn eDiender

    2015-11-01

    Full Text Available Carbon monoxide can act as a substrate for different modes of fermentative anaerobic metabolism. The trait of utilizing CO is spread among a diverse group of microorganisms, including members of bacteria as well as archaea. Over the last decade this metabolism has gained interest due to the potential of converting CO rich gas, such as synthesis gas, into bio-based products. Three main types of fermentative CO metabolism can be distinguished: hydrogenogenesis, methanogenesis and acetogenesis, generating hydrogen, methane and acetate, respectively. Here, we review the current knowledge on these three variants of microbial CO metabolism with an emphasis on the potential enzymatic routes and bio-energetics involved.

  1. OMI Observations of Bromine Monoxide Emissions from Volcanoes

    Science.gov (United States)

    Suleiman, R. M.; Chance, K.; Liu, X.; Gonzalez Abad, G.; Kurosu, T. P.

    2016-12-01

    We analyze bromine monoxide (BrO) data from the Ozone Monitoring Instrument (OMI) for emissions from various volcanoes. We use OMI data from 2005 to 2014 to investigate BrO signatures from Galapagos, Kasatochi and Eyjafjallajökull volcanoes. Elevated signatures of BrO daily averages were found over Eyjafjallajökull. SO2 cross sections are updated in the operational BrO algorithm and their effect on the volcanic BrO signature is studied. Comparison between two different sets of SO2 cross sections is made and results still show BrO enhancement over the Eyjafjallajökull region.

  2. Studies relevant to the catalytic activation of carbon monoxide

    Energy Technology Data Exchange (ETDEWEB)

    Ford, P.C.

    1992-06-04

    Research activity during the 1991--1992 funding period has been concerned with the following topics relevant to carbon monoxide activation. (1) Exploratory studies of water gas shift catalysts heterogenized on polystyrene based polymers. (2) Mechanistic investigation of the nucleophilic activation of CO in metal carbonyl clusters. (3) Application of fast reaction techniques to prepare and to investigate reactive organometallic intermediates relevant to the activation of hydrocarbons toward carbonylation and to the formation of carbon-carbon bonds via the migratory insertion of CO into metal alkyl bonds.

  3. Dipolar dissociation dynamics in electron collisions with carbon monoxide

    CERN Document Server

    Chakraborty, Dipayan; Nandi, Dhananjay

    2016-01-01

    Dipolar dissociation processes in the electron collisions with carbon monoxide have been studied using time of flight (TOF) mass spectroscopy in combination with the highly differential velocity slice imaging (VSI) technique. Probing ion-pair states both positive and/or negative ions may be detected. The ion yield curve of negative ions provides the threshold energy for the ion-pair production. On the other hand, the kinetic energy distributions and angular distributions of the fragment anion provide detailed dynamics of the dipolar dissociation process. Two ion-pair states have been identified based on angular distribution measurements using VSI technique.

  4. A new approach to detect local correlations of tropospheric acetone and carbon monoxide sampled onboard the IAGOS-CARIBIC passenger aircraft

    Science.gov (United States)

    Fischbeck, Garlich; Neumaier, Marco; Safadi, Layal; Zahn, Andreas

    2016-04-01

    Since 2005 a Lufthansa passenger aircraft is regularly used as a platform for in-situ measurements in the upper troposphere and lowermost stratosphere (UTLMS). Accommodated in a modified airfreight container 15 instruments are deployed in the cargo bay of the aircraft on four selected intercontinental flights per month measuring ~100 species and aerosol parameters. In contrast to other projects of this scope, using a chemical mass spectrometer also volatile organic compounds like acetone (CH3COCH3) and acetonitrile (CH3CN) are detected enabling an investigation of their relationship with other tracers. On a global scale acetone is predominantly emitted from the biosphere (~37 Tg/a; MEGAN-MACC, Sinderarova et al. 2014) and comparably small amounts are directly emitted from biomass burning (~2 Tg/a; GFED3, Van der Werf et al. 2010) and other anthropogenic sources (~1 Tg/a; MACCity, Granier et al. 2011). However, at local levels the contributions from the different sources can strongly differ. Acetone is also secondarily produced in the atmosphere by the oxidation of various precursors, e.g. pinene and propane. The emissions of these precursors and their contribution to the total acetone source are not well known and a topic of ongoing discussions. In this context it is initially surprising that generally a good correlation between acetone and carbon monoxide (CO) has been observed in the lower atmosphere by different authors (e.g. de Reus et al. 2003). As a product of incomplete combustion CO is regularly used as a tracer for anthropogenic pollution and biomass burning. In this study we present an improved method to detect local correlations in IAGOS-CARIBIC flights instead of mixing data from different flights or measured over great distances. Furthermore, a cluster analysis is applied to prevent the consideration of artificial correlations between two well separated clouds of data points. We use the concept of enhancement ratios (EnR) and a simple box model to

  5. On the linearity of tracer bias around voids

    Science.gov (United States)

    Pollina, Giorgia; Hamaus, Nico; Dolag, Klaus; Weller, Jochen; Baldi, Marco; Moscardini, Lauro

    2017-07-01

    The large-scale structure of the Universe can be observed only via luminous tracers of the dark matter. However, the clustering statistics of tracers are biased and depend on various properties, such as their host-halo mass and assembly history. On very large scales, this tracer bias results in a constant offset in the clustering amplitude, known as linear bias. Towards smaller non-linear scales, this is no longer the case and tracer bias becomes a complicated function of scale and time. We focus on tracer bias centred on cosmic voids, i.e. depressions of the density field that spatially dominate the Universe. We consider three types of tracers: galaxies, galaxy clusters and active galactic nuclei, extracted from the hydrodynamical simulation Magneticum Pathfinder. In contrast to common clustering statistics that focus on auto-correlations of tracers, we find that void-tracer cross-correlations are successfully described by a linear bias relation. The tracer-density profile of voids can thus be related to their matter-density profile by a single number. We show that it coincides with the linear tracer bias extracted from the large-scale auto-correlation function and expectations from theory, if sufficiently large voids are considered. For smaller voids we observe a shift towards higher values. This has important consequences on cosmological parameter inference, as the problem of unknown tracer bias is alleviated up to a constant number. The smallest scales in existing data sets become accessible to simpler models, providing numerous modes of the density field that have been disregarded so far, but may help to further reduce statistical errors in constraining cosmology.

  6. Carbon Monoxide Accumulation in the Extravehicular Mobility Unit

    Science.gov (United States)

    Conkin, J.; Norcrosss, J. R.; Alexander, D. J.; Sanders, R. W.; Makowski, M. S.

    2016-01-01

    Introduction: Life support technology in large closed systems like submarines and space stations catalyzes carbon monoxide (CO) to carbon dioxide, which is easily removed. However, in a small system like the Extravehicular Mobility Unit (EMU), spacesuit, CO from exogenous (contaminated oxygen (O (sub 2) supply) and endogenous (human metabolism) sources will accumulate in the free suit volume. The free volume becomes a sink for CO that is rebreathed by the astronaut. The accumulation through time depends on many variables: the amount absorbed by the astronaut, the amount produced by the astronaut (between 0.28 and 0.34 ?moles per hour per kilogram)[1], the amount that enters the suit from contaminated O (sub 2), the amount removed through suit leak, the free volume of the suit, and the O (sub 2) partial pressure[2], just to list a few. Contamination of the EMU O (sub 2) supply with no greater than 1 part per million CO was the motivation for empirical measurements from CO pulse oximetry (SpCO) as well as mathematical modeling of the EMU as a rebreather for CO. Methods: We developed a first-order differential mixing equation as well as an iterative method to compute CO accumulation in the EMU. Pre-post measurements of SpCO (Rad-57, Masimo Corporation) from EMU ground training and on-orbit extravehicular activities (EVAs) were collected. Results: Initial modeling without consideration of the astronaut as a sink but only the source of CO showed that after 8 hours breathing 100 percent O (sub 2) with a 10 milliliter per minute (760 millimeters Hg at 21 degrees Centigrade standard) suit leak, an endogenous production rate of 0.23 moles per hour per kilogram for a 70 kilogram person with 42 liters (1.5 cubic feet) free suit volume resulted in a peak CO partial pressure (pCO) of 0.047 millimeters Hg at 4.3 pounds per square inch absolute (222 millimeters Hg). Preliminary results based on a 2008 model[3] with consideration of the astronaut as a sink and source of CO

  7. Tracer gas dispersion in ducts-study of a new compact device using arrays of sonic micro jets

    Energy Technology Data Exchange (ETDEWEB)

    Silva, A.R. [Instituto Nacional de Engenharia e Tecnologia Industrial (INETI), Lisboa (Portugal); Afonso, C.F. [Faculdade de Engenharia, Universidade do Porto Departmento de Mecanica e Gestao Industrial, Porto (Portugal)

    2004-07-01

    One of the most feasible ways to measure duct airflows is by tracer gas techniques, especially for complex situations when the duct lengths are short as well as their access, which makes extremely difficult or impossible other methods to be implemented. One problem associated with the implementation of tracer gas technique when the ducts lengths are short is due to the impossibility of achieving complete mixing of the tracer with airflow and its sampling. In this work, the development of a new device for the injection of tracer gas in ducts is discussed as well as a new tracer-sampling device. The developed injection device has a compact tubular shape, with magnetic fixation to be easy to apply in duct walls. An array of sonic micro jets in counter current direction, with the possibility of angular movement according to its main axle ensures a complete mixing of the tracer in very short distances. The tracer-sampling device, with a very effective integration function, feeds the sampling system for analysis. Both devices were tested in a wind tunnel of approximately 21 m total length. The tests distances between injection and integration device considered were: X/Dh = 22; X/Dh = 4; X/Dh 2; and X/Dh = 1. For very short distances of X/Dh = 2 and X/Dh = 1, semi-empirical expressions were needed. A good reproducibility of airflow rate values was obtained. These preliminary tests showed that the practical implementation of tracer gas techniques in HVAC systems for measuring airflow rates with a very short mixing distance is possible with the devices developed. (author)

  8. Development of an Instrument Performance Simulation Capability for an Infrared Correlation Radiometer for Troposheric Carbon Monoxide Measurements From Geo

    Science.gov (United States)

    OsowskiNeil, Doreen; Yee, Jeng-Hwa; Boldt, John; Edwards, David

    2010-01-01

    We present the progress toward an analytical performance model of a 2.3 micron infrared correlation radiometer (IRCRg) prototype subsystem for a future geostationary space-borne instrument. The prototype is designed specifically to measure carbon monoxide (CO) from geostationary orbit. NASA's Geostationary Coastal and Air Pollution Events (GEO-CAPE) mission, one of the United States Earth Science and Applications Decadal Survey missions, specifies the use of infrared correlation radiometry to measure CO in two spectral regions for this mission. GEO-CAPE will use the robust IRCR measurement technique at geostationary orbit, nearly 50 times farther away than the Terra/MOPITT orbit, to determine hourly changes in CO across a continental domain. The abundance of CO in Earth's troposphere directly affects the concentration of hydroxyl, which regulates the lifetimes of many tropospheric pollutants. In addition, CO is a precursor to ozone formation; CO is used as a tracer to study the transport of global and regional pollutants; and CO is used as an indicator of both natural and anthropogenic air pollution sources and sinks. We have structured our development project to enable rapid evaluation of future spaceborne instrument designs. The project is part of NASA's Instrument Incubator Program. We describe the architecture of the performance model and the planned evaluation of the performance model using laboratory test data.

  9. Tracers to investigate protein and amino acid metabolism in human subjects.

    Science.gov (United States)

    Wagenmakers, A J

    1999-11-01

    Three tracer methods have been used to measure protein synthesis, protein breakdown and protein oxidation at whole-body level. The method using L-[1-(13)C]leucine is considered the method of reference. These methods have contributed greatly to the existing knowledge on whole-body protein turnover and its regulation by feeding, fasting, hormones and disease. How exercise and ingestion of mixed protein-containing meals affect whole-body protein metabolism is still open to debate, as there are discrepancies in results obtained with different tracers. The contribution of whole-body methods to the future gain of knowledge is expected to be limited due to the fact that most physiological disturbances have been investigated extensively, and due to the lack of information on the relative contribution of various tissues and proteins to whole-body changes. Tracer amino acid-incorporation methods are most suited to investigate these latter aspects of protein metabolism. These methods have shown that some tissues (liver and gut) have much higher turnover rates and deposit much more protein than others (muscle). Massive differences also exist between the fractional synthesis rates of individual proteins. The incorporation methods have been properly validated, although minor disagreements remain on the identity of the true precursor pool (the enrichment of which should be used in the calculations). Arterio-venous organ balance studies have shown that little protein is deposited in skeletal muscle following a protein-containing meal, while much more protein is deposited in liver and gut. The amount deposited in the feeding period in each of these tissues is released again during overnight fasting. The addition of tracers to organ balance studies allows the simultaneous estimation of protein synthesis and protein breakdown, and provides information on whether changes in net protein balance are caused primarily by a change in protein synthesis or in protein breakdown. In the case

  10. Star clusters as tracers of galaxy evolution

    CERN Document Server

    Konstantopoulos, Iraklis S

    2009-01-01

    Star clusters represent the most common 'mode' of star formation. They are found in all types of environments, cascading down from galaxy groups and merging pairs through starbursts to normal galaxies and dwarves and even isolated regions in extragalactic space. As they maintain a link to the overall star formation in a system, they can be used as tracers of the star formation history of environments located at distances prohibitive to the study of individual stars. This makes them ideally suited to the study of mergers and interactions in galaxy pairs and groups. In this work we present observations of the star cluster populations in the local starburst galaxy M82, post-interaction spiral NGC 6872, the "Antennae" merging pair and two compact groups, "Stephan's Quintet" and HCG 7. In each case, we extract information on the clusters and their hosts using mainly HST photometry and Gemini spectroscopy.

  11. Elemental tracers for Chinese source dust

    Institute of Scientific and Technical Information of China (English)

    张小曳; 张光宇; 朱光华; 张德二; 安芷生; 陈拓; 黄湘萍

    1996-01-01

    The mass-particle size distributions of 10 dust-carrying elements in aerosol particles were determined tor 12 sites in desert regions of northern China. The desert dust is proved to he of origin of eolian loess deposited on the Loess Plateau. Their transport to the loess was mainly attributable to the non-dust storm processes under the interglacial climate condition. The impact ot" dust storm on the accumulation of the loess increased in the glacial stage. On the basis of the signatures of 4 dust elements (Al. Fe, Mg and Sc). Chinese dust is believed to have 3 major desert sources (northwestern deserts, northern high dust deserts and northern low dust deserts). With a chemical element balance model, an elemental tracer system is established to proportion the export of China-source dust.

  12. Tracer studies of nitrogen assimilation in yeast.

    Science.gov (United States)

    ABRAMS, R; HAMMARSTEN, E

    1949-01-01

    By using N(15) as a tracer the assimilation of ammonia by the yeast, Torulopsis utilis, has been studied. It has been shown that: 1. There was no measurable incorporation of N in the protein or polynucleotide purine of carbon-starved yeast. 2. When ammonia is added to nitrogen-starved yeast there is a long lag period before division begins during which the yeast rapidly synthesizes protein, this process being accompanied by a turnover of polynucleotide purine. There was no significant dilution of the N(15)H(4) (+) of the medium by ordinary NH(4) (+). 3. When yeast containing N(15) is allowed to divide and grow in ordinary ammonia, the total amount of N(15) in the yeast remains constant. The dicarboxylic amino acids are most diluted, while arginine and nucleic acid guanine are not diluted at all.

  13. National Biomedical Tracer Facility. Project definition study

    Energy Technology Data Exchange (ETDEWEB)

    Schafer, R.

    1995-02-14

    We request a $25 million government-guaranteed, interest-free loan to be repaid over a 30-year period for construction and initial operations of a cyclotron-based National Biomedical Tracer Facility (NBTF) in North Central Texas. The NBTF will be co-located with a linear accelerator-based commercial radioisotope production facility, funded by the private sector at approximately $28 million. In addition, research radioisotope production by the NBTF will be coordinated through an association with an existing U.S. nuclear reactor center that will produce research and commercial radioisotopes through neutron reactions. The combined facilities will provide the full range of technology for radioisotope production and research: fast neutrons, thermal neutrons, and particle beams (H{sup -}, H{sup +}, and D{sup +}). The proposed NBTF facility includes an 80 MeV, 1 mA H{sup -} cyclotron that will produce proton-induced (neutron deficient) research isotopes.

  14. Urban Pollutant Transport and Infiltration into Buildings Using Perfluorocarbon Tracers

    Science.gov (United States)

    Matthews, James C.; Bacak, Asan; Khan, M. Anwar H.; Wright, Matthew D.; Priestley, Michael; Martin, Damien; Percival, Carl J.; Shallcross, Dudley E.

    2017-01-01

    People spend the majority of their time indoors and therefore the quality of indoor air is worthy of investigation; indoor air quality is affected by indoor sources of pollutants and from pollutants entering buildings from outdoors. In this study, unique perfluorocarbon tracers were released in five experiments at a 100 m and ~2 km distance from a large university building in Manchester, UK and tracer was also released inside the building to measure the amount of outdoor material penetrating into buildings and the flow of material within the building itself. Air samples of the tracer were taken in several rooms within the building, and a CO2 tracer was used within the building to estimate air-exchange rates. Air-exchange rates were found to vary between 0.57 and 10.90 per hour. Indoor perfluorocarbon tracer concentrations were paired to outdoor tracer concentrations, and in-out ratios were found to vary between 0.01 and 3.6. The largest room with the lowest air-exchange rate exhibited elevated tracer concentrations for over 60 min after the release had finished, but generally had the lowest concentrations, the room with the highest ventilation rates had the highest concentration over 30 min, but the peak decayed more rapidly. Tracer concentrations indoors compared to outdoors imply that pollutants remain within buildings after they have cleared outside, which must be considered when evaluating human exposure to outdoor pollutants. PMID:28230812

  15. Urban Pollutant Transport and Infiltration into Buildings Using Perfluorocarbon Tracers.

    Science.gov (United States)

    Matthews, James C; Bacak, Asan; Khan, M Anwar H; Wright, Matthew D; Priestley, Michael; Martin, Damien; Percival, Carl J; Shallcross, Dudley E

    2017-02-21

    People spend the majority of their time indoors and therefore the quality of indoor air is worthy of investigation; indoor air quality is affected by indoor sources of pollutants and from pollutants entering buildings from outdoors. In this study, unique perfluorocarbon tracers were released in five experiments at a 100 m and ~2 km distance from a large university building in Manchester, UK and tracer was also released inside the building to measure the amount of outdoor material penetrating into buildings and the flow of material within the building itself. Air samples of the tracer were taken in several rooms within the building, and a CO₂ tracer was used within the building to estimate air-exchange rates. Air-exchange rates were found to vary between 0.57 and 10.90 per hour. Indoor perfluorocarbon tracer concentrations were paired to outdoor tracer concentrations, and in-out ratios were found to vary between 0.01 and 3.6. The largest room with the lowest air-exchange rate exhibited elevated tracer concentrations for over 60 min after the release had finished, but generally had the lowest concentrations, the room with the highest ventilation rates had the highest concentration over 30 min, but the peak decayed more rapidly. Tracer concentrations indoors compared to outdoors imply that pollutants remain within buildings after they have cleared outside, which must be considered when evaluating human exposure to outdoor pollutants.

  16. On the linearity of tracer bias around voids

    CERN Document Server

    Pollina, Giorgia; Dolag, Klaus; Weller, Jochen; Baldi, Marco; Moscardini, Lauro

    2016-01-01

    The large-scale structure of the universe can only be observed directly via luminous tracers of the underlying distribution of dark matter. However, the clustering statistics of tracers are biased and depend on various properties of the tracers themselves, such as their host-halo mass and formation and assembly history. On very large scales, where density fluctuations are within the linear regime, this tracer bias results in a constant offset in the clustering amplitude, which is known as linear bias. Towards smaller non-linear scales, this is no longer the case and tracer bias becomes a complicated function of scale and time. We focus on tracer bias centered on cosmic voids, depressions of the density field that spatially dominate the universe. We consider three different types of tracers: galaxies, galaxy clusters and AGNs, extracted from the hydrodynamical simulation suite Magneticum Pathfinder. In contrast to common clustering statistics that focus on the auto-correlation of tracers, we find that void-tra...

  17. Toxicity of fluorescent tracers and their degradation byproducts

    Directory of Open Access Journals (Sweden)

    Philippe Gombert

    2017-01-01

    Full Text Available Tracer tests are frequently used to delineate catchment area of water supply springs in karstic zones. In the karstic chalk of Normandy, the main tracers used are fluorescent: uranine, sulforhodamine B, naphtionate, and Tinopal®. In this area, a statistical analysis shows that less than half of the injected tracers joins the monitored restitution points and enters the drinking water system where they undergo chlorination. Most of the injected tracers is absorbed in the rock matrix or is thrown out of the aquifer via karstic springs: then it can join superficial waters where it is degraded due to the sun and air action. The paper presents firstly the laboratory degradation of a first batch of fluorescent tracers in contact with chlorine, in order to simulate their passage through a water treatment system for human consumption. A second batch of the same tracers is subjected to agents of natural degradation: ultraviolet illumination, sunlight and air sparging. Most tracers is degraded, and toxicity and ecotoxicity tests (on rats, daphniae and algae are performed on degradation byproducts. These tests do not show any acute toxicity but a low to moderate ecotoxicity. In conclusion, the most used fluorescent tracers of the Normandy karstic chalk and their artificial and natural degradation byproducts do not exhibit significant toxicity to humans and the aquatic environment, at the concentrations generally noted at the restitution points.

  18. Material processing with hydrogen and carbon monoxide on Mars

    Science.gov (United States)

    Hepp, Aloysius F.; Landis, Geoffrey A.; Linne, Diane L.

    1991-01-01

    Several novel proposals are examined for propellant production from carbon dioxide and monoxide and hydrogen. Potential uses were also examined of CO as a fuel or as a reducing agent in metal oxide processing as obtained or further reduced to carbon. Hydrogen can be reacted with CO to produce a wide variety of hydrocarbons, alcohols, and other organic compounds. Methanol, produced by Fischer-Tropsch chemistry may be useful as a fuel; it is easy to store and handle because it is a liquid at Mars temperatures. The reduction of CO2 to hydrocarbons such as methane or acetylene can be accomplished with hydrogen. Carbon monoxide and hydrogen require cryogenic temperatures for storage as liquids. Noncryogenic storage of hydrogen may be accomplished using hydrocarbons, inorganic hydrides, or metal hydrides. Noncryogenic storage of CO may be accomplished in the form of iron carbonyl (FE(CO)5) or other metal carbonyls. Low hydrogen content fuels such as acetylene (C2H2) may be effective propellants with low requirements for earth derived resources. The impact on manned Mars missions of alternative propellant production and utilization is discussed.

  19. Space-based observation of volcanic iodine monoxide

    Science.gov (United States)

    Schönhardt, Anja; Richter, Andreas; Theys, Nicolas; Burrows, John P.

    2017-04-01

    Volcanic eruptions inject substantial amounts of halogens into the atmosphere. Chlorine and bromine oxides have frequently been observed in volcanic plumes from different instrumental platforms such as from ground, aircraft and satellites. The present study is the first observational evidence that iodine oxides are also emitted into the atmosphere during volcanic eruptions. Large column amounts of iodine monoxide, IO, are observed in satellite measurements following the major eruption of the Kasatochi volcano, Alaska, in 2008. The IO signal is detected in measurements made both by SCIAMACHY (Scanning Imaging Absorption Spectrometer for Atmospheric CHartographY) on ENVISAT (Environmental Satellite) and GOME-2 (Global Ozone Monitoring Experiment-2) on MetOp-A (Meteorological Operational Satellite A). Following the eruption on 7 August 2008, strongly elevated levels of IO slant columns of more than 4 × 1013 molec cm-2 are retrieved along the volcanic plume trajectories for several days. The retrieved IO columns from the different instruments are consistent, and the spatial distribution of the IO plume is similar to that of bromine monoxide, BrO. Details in the spatial distribution, however, differ between IO, BrO and sulfur dioxide, SO2. The column amounts of IO are approximately 1 order of magnitude smaller than those of BrO. Using the GOME-2A observations, the total mass of IO in the volcanic plume injected into the atmosphere from the eruption of Kasatochi on 7 August 2008, is determined to be on the order of 10 Mg.

  20. The electric dipole moment of cobalt monoxide, CoO.

    Science.gov (United States)

    Zhuang, Xiujuan; Steimle, Timothy C

    2014-03-28

    A number of low-rotational lines of the E(4)Δ7/2 ← X(4)Δ7/2 (1,0) band system of cobalt monoxide, CoO, were recorded field free and in the presence of a static electric field. The magnetic hyperfine parameter, h7/2, and the electron quadrupole parameter, eQq0, for the E(4)Δ7/2(υ = 1) state were optimized from the analysis of the field-free spectrum. The permanent electric dipole moment, μ(→)(el), for the X(4)Δ7/2 (υ = 0) and E(4)Δ7/2 (υ = 1) states were determined to be 4.18 ± 0.05 D and 3.28 ± 0.05 D, respectively, from the analysis of the observed Stark spectra of F' = 7 ← F″ = 6 branch feature in the Q(7/2) line and the F' = 8 ← F″ = 7 branch feature in the R(7/2) line. The measured dipole moments of CoO are compared to those from theoretical predictions and the trend across the 3d-metal monoxide series discussed.

  1. Carbon Monoxide Emissions in Middle Aged Debris Disks

    Science.gov (United States)

    Henderson, Morgan; Gorti, Uma; Hales, Antonio; Carpenter, John M.; Hughes, A. Meredith

    2017-01-01

    Circumstellar disks greater than 10 Myr old, referred to as debris disks, are expected to be gas poor. The original gas and dust in these disks is thought to be accreted onto the host stars, used up in the formation of planets and other bodies, or blown out of the disks via stellar radiation. However, recent ALMA observations at millimeter wavelengths have led to the detection of carbon monoxide (J=2-1) emission in a few debris disks, prompting further investigation.Using ALMA data, two separate models of gas genesis were tested against observations of the CO emissions in the disks around HIP 73145, HIP 76310, and HIP 84881 in the Upper Sco association. One of these models was built on the hypothesis that the gas in these debris disks is left over from stellar formation and has persisted over uncommonly long periods of time. The other model is built on the hypothesis that this gas is of secondary nature, produced by collisions between planetary bodies in the debris disks. Model emissions were calculated using the Line Modeling Engine (LIME) radiative transfer code and were compared with observational data to infer gas masses under both production scenarios. The implications of the masses of carbon monoxide in the disks suggested by each of the two models are discussed.

  2. Predicting Cardiotoxic Effects of Carbon Monoxide Poisoning Using Speckle Tracking Echocardiography.

    Science.gov (United States)

    Saraçoğlu, Erhan; Vuruşkan, Ertan; Kılıç, Salih; Çekici, Yusuf; Onur, Bahaeddin; Arslan, Yavuz; Kılıç, Ertuğrul; Aykut, Ömer

    2017-10-06

    Carbon monoxide (CO) poisoning could cause significant cardiac injury. This study aimed to evaluate patients with CO poisoning by using speckle tracking echocardiography (STE), a potentially more sensitive technique, to identify left systolic ventricular dysfunction for the first time in the literature. Seventy-two patients who were exposed to CO poisoning were studied. Blood collection and echocardiography were performed at admission and after patients' discharge on days 10-15 (mean 12 days). Global longitudinal strain (GLS) and global circumferential strain (GCS) were calculated using STE. In order to find the normal strain levels and to compare it to the patient with CO poisoning, 35 healthy subjects were included in the study. Left ventricular ejection fraction was analyzed according to Simpson's method. Patients were divided into two groups based on their LVEF values. LVEF Speckle tracking echocardiography has the potential of demonstrating subtle LV systolic dysfunction even in CO poisoning patients with preserved EF.

  3. A Density Functional Theory Study of Doped Tin Monoxide as a Transparent p-type Semiconductor

    KAUST Repository

    Bianchi Granato, Danilo

    2012-05-01

    In the pursuit of enhancing the electronic properties of transparent p-type semiconductors, this work uses density functional theory to study the effects of doping tin monoxide with nitrogen, antimony, yttrium and lanthanum. An overview of the theoretical concepts and a detailed description of the methods employed are given, including a discussion about the correction scheme for charged defects proposed by Freysoldt and others [Freysoldt 2009]. Analysis of the formation energies of the defects points out that nitrogen substitutes an oxygen atom and does not provide charge carriers. On the other hand, antimony, yttrium, and lanthanum substitute a tin atom and donate n-type carriers. Study of the band structure and density of states indicates that yttrium and lanthanum improves the hole mobility. Present results are in good agreement with available experimental works and help to improve the understanding on how to engineer transparent p-type materials with higher hole mobilities.

  4. 40 CFR 52.1627 - Control strategy and regulations: Carbon monoxide.

    Science.gov (United States)

    2010-07-01

    ...: Carbon monoxide. 52.1627 Section 52.1627 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) New Mexico § 52.1627 Control strategy and regulations: Carbon monoxide. (a) Part D Approval. The...

  5. Using conversions of chemically reacting tracers for numerical determination of temperature profiles in flowing systems and temperature histories in batch systems

    Energy Technology Data Exchange (ETDEWEB)

    Brown, L.F.; Chemburkar, R.M.; Robinson, B.A.; Travis, B.J.

    1996-04-01

    This report presents the mathematical bases for measuring internal temperatures within batch and flowing systems using chemically reacting tracers. This approach can obtain temperature profiles of plug-flow systems and temperature histories within batch systems. The differential equations for reactant conversion can be converted into Fredholm integral equations of the first kind. The experimental variable is the tracer-reaction activation energy. When more than one tracer is used, the reactions must have different activation energies to gain information. In systems with temperature extrema, multiple solutions for the temperature profiles or histories can exist, When a single parameter in the temperature distribution is needed, a single-tracer test may furnish this information. For multi-reaction tracer tests, three Fredholm equations are developed. Effects of tracer-reaction activation energy, number of tracers used, and error in the data are evaluated. The methods can determine temperature histories and profiles for many existing systems, and can be a basis for analysis of the more complicated dispersed-flow systems. An alternative to using the Fredholm-equation approach is the use of an assumed temperature- distribution function and incorporation of this function into the basic integral equation describing tracer behavior. The function contains adjustable parameters which are optimized to give the temperature distribution. The iterative Fredholm equation method is tested to see what is required to discriminate between two models of the temperature behavior of Hot Dry Rock (HDR) geothermal reservoirs. Experimentally, ester and amide hydrolyses are valid HDR tracer reactions for measuring temperatures in the range 75-100{degrees}C. Hydrolyses of bromobenzene derivatives are valid HDR tracer reactions for measuring temperatures in the range 150-275{degrees}C.

  6. Sci-Fri AM: Imaging - 09: Serial estimation of cross-talk for correction in dual-isotope imaging with dynamic tracers.

    Science.gov (United States)

    Wells, R G; Lockwood, J; Wei, L; Duan, D; Fernando, P; Bensimon, C; Ruddy, T D

    2012-07-01

    The recent radioisotope shortage has led to interest in non-Tc99m-based tracers. We have developed a novel I-123-labelled myocardial perfusion imaging tracer. We compare the I123-tracer to the clinical standard of Tc99m tetrofosmin in vivo in a rat model using a small-animal SPECT/CT camera. SPECT distinguishes different isotopes based on the different energies of the emitted gamma rays and thus allows simultaneous comparison of two tracer distributions in the same animal. Dual-isotope imaging is complicated by cross-talk between the energy windows of the isotopes. Standard energy-window-based correction methods are difficult to employ because of the proximity in energy of Tc99m (140keV) and I123 (159keV). Imaging the second tracer's energy window prior to its injection provides an estimate of the cross-talk. However, this estimate is only accurate if the tracer distribution is static. We use serial imaging prior to the introduction of the second tracer to estimate the dynamics of the first tracer and interpolate the cross-talk images to provide a more accurate correction. We used rat models of myocardial disease (n=3). I123 tracer was injected and imaged for one hour at 20min intervals. The Tc99m tetrofosmin was then injected and 30min later, a dual-isotope image was obtained. The impact of this approach is assessed by comparing the differences in the Tc99m-tetrofosmin image using this method with correction by simple correction for physical decay. The interpolative approach improves the accuracy of the correction by 2%-5% and thereby enhances the comparison of the two tracers. © 2012 American Association of Physicists in Medicine.

  7. STRATEGIES FOR QUANTIFYING PET IMAGING DATA FROM TRACER STUDIES OF BRAIN RECEPTORS AND ENZYMES.

    Energy Technology Data Exchange (ETDEWEB)

    Logan, J.

    2001-04-02

    A description of some of the methods used in neuroreceptor imaging to distinguish changes in receptor availability has been presented in this chapter. It is necessary to look beyond regional uptake of the tracer since uptake generally is affected by factors other than the number of receptors for which the tracer has affinity. An exception is the infusion method producing an equilibrium state. The techniques vary in complexity some requiring arterial blood measurements of unmetabolized tracer and multiple time uptake data. Others require only a few plasma and uptake measurements and those based on a reference region require no plasma measurements. We have outlined some of the limitations of the different methods. Laruelle (1999) has pointed out that test/retest studies to which various methods can be applied are crucial in determining the optimal method for a particular study. The choice of method will also depend upon the application. In a clinical setting, methods not involving arterial blood sampling are generally preferred. In the future techniques for externally measuring arterial plasma radioactivity with only a few blood samples for metabolite correction will extend the modeling options of clinical PET. Also since parametric images can provide information beyond that of ROI analysis, improved techniques for generating such images will be important, particularly for ligands requiring more than a one-compartment model. Techniques such as the wavelet transform proposed by Turkheimer et al. (2000) may prove to be important in reducing noise and improving quantitation.

  8. Characterization of an alluvial aquifer with thermal tracer tomography

    Science.gov (United States)

    Somogyvári, Márk; Bayer, Peter

    2017-04-01

    In the summer of 2015, a series of thermal tracer tests was performed at the Widen field site in northeast Switzerland. At this site numerous hydraulic, tracer, geophysical and hydrogeophysical field tests have been conducted in the past to investigate a shallow alluvial aquifer. The goals of the campaign in 2015 were to design a cost-effective thermal tracer tomography setup and to validate the concept of travel time-based thermal tracer tomography under field conditions. Thermal tracer tomography uses repeated thermal tracer injections with different injection depths and distributed temperature measurements to map the hydraulic conductivity distribution of a heterogeneous aquifer. The tracer application was designed with minimal experimental time and cost. Water was heated in inflatable swimming pools using direct sunlight of the warm summer days, and it was injected as low temperature pulses in a well. Because of the small amount of injected heat, no long recovery times were required between the repeated heat tracer injections and every test started from natural thermal conditions. At Widen, four thermal tracer tests were performed during a period of three days. Temperatures were measured in one downgradient well using a distributed temperature measurement system installed at seven depth points. Totally 12 temperature breakthrough curves were collected. Travel time based tomographic inversion assumes that thermal transport is dominated by advection and the travel time of the thermal tracer can be related to the hydraulic conductivities of the aquifer. This assumption is valid in many shallow porous aquifers where the groundwater flow is fast. In our application, the travel time problem was treated by a tomographic solver, analogous to seismic tomography, to derive the hydraulic conductivity distribution. At the test site, a two-dimensional cross-well hydraulic conductivity profile was reconstructed with the travel time based inversion. The reconstructed profile

  9. 耳针作用的形态学基础-来自HRP神经示踪法的证据%Morphological Basis of Auricular Acupuncture Effects: Evidences from Neural Tracer Method of HRP

    Institute of Scientific and Technical Information of China (English)

    梅志刚; 朱兵; 何伟; 高昕妍

    2009-01-01

    Objective To observe projections of nervus auricularis vagi in brain stem of oblongata level,and to study the mechanism of auricular acupuncture. Methods Ten SD rats were used in this experiment, a skin incision was performed in the region of auricular concha of each rat, forty microliters of a 30% solution of horseradish peroxidase (HRP) in normal saline were subcuta-neously injected into the cut central end of auricular branch of vagus nerve, then distribution of the labeled neurons in the primary brain stem was observed using HRP retrograde tracing technique. Results Labeled neurons and fibers were seen in the nucleus of solitary tract, dorsal nucleus of vagus nerve and other nucleus besides nucleus of spinal tract of trigeminal. Conclusion There exists neural projection to NTS and DMV from the terminal of auricular vagus branch, maybe effect of auricular acupuncture is completed through auricular - vagal reflexes.%目的 观察支配耳甲区迷走神经在延髓水平中枢的投射情况,探讨耳针作用机理.方法 健康成年SD大鼠10只,外耳道口方向分离耳甲皮肤与皮下组织,微量注射器缝内注射40 μl 浓度为30%的HRP神经示踪剂,神经示踪技术观察标记细胞在延脑水平核团分布情况.结果 除了在三叉神经脊束核外,在孤束核和迷走神经运动背核以及其他核团也发现了标记神经元或神经纤维.结论 耳甲区迷走神经分支与迷走初级中枢有神经联系,耳甲穴位针刺效应很可能是通过耳-迷走反射途径实现的.

  10. The deployment of carbon monoxide wireless sensor network (CO-WSN) for ambient air monitoring.

    Science.gov (United States)

    Chaiwatpongsakorn, Chaichana; Lu, Mingming; Keener, Tim C; Khang, Soon-Jai

    2014-06-16

    Wireless sensor networks are becoming increasingly important as an alternative solution for environment monitoring because they can reduce cost and complexity. Also, they can improve reliability and data availability in places where traditional monitoring methods are difficult to site. In this study, a carbon monoxide wireless sensor network (CO-WSN) was developed to measure carbon monoxide concentrations at a major traffic intersection near the University of Cincinnati main campus. The system has been deployed over two weeks during Fall 2010, and Summer 2011-2012, traffic data was also recorded by using a manual traffic counter and a video camcorder to characterize vehicles at the intersection 24 h, particularly, during the morning and evening peak hour periods. According to the field test results, the 1 hr-average CO concentrations were found to range from 0.1-1.0 ppm which is lower than the National Ambient Air Quality Standards (NAAQS) 35 ppm on a one-hour averaging period. During rush hour periods, the traffic volume at the intersection varied from 2,067 to 3,076 vehicles per hour with 97% being passenger vehicles. Furthermore, the traffic volume based on a 1-h average showed good correlation (R2 = 0.87) with the 1-h average CO-WSN concentrations for morning and evening peak time periods whereas CO-WSN results provided a moderate correlation (R2 = 0.42) with 24 hours traffic volume due to fluctuated changes of meteorological conditions. It is concluded that the performance and the reliability of wireless ambient air monitoring networks can be used as an alternative method for real time air monitoring.

  11. Arabitol and mannitol as tracers for the quantification of airborne fungal spores

    Science.gov (United States)

    Bauer, Heidi; Claeys, Magda; Vermeylen, Reinhilde; Schueller, Elisabeth; Weinke, Gert; Berger, Anna; Puxbaum, Hans

    Fungal spores constitute a sizeable fraction of coarse organic carbon (OC) in the atmospheric aerosol. In order to avoid tedious spore count methods, tracers for quantifying the spore-OC in atmospheric aerosol are sought. Arabitol and mannitol have been proposed as such tracers, since no other emission sources for these compounds have been reported. By parallel investigations of spore counts and tracer determinations from PM 10 filter samples we could derive quantitative relationships between the amounts of tracer compounds and the numbers of spores in the atmosphere for different sites in the area of Vienna. We obtained over all average relationships of 1.2 pg arabitol spore -1, with a range of 0.8-1.8, and 1.7 pg mannitol spore -1, with a range of 1.2-2.4, with a clear site dependence. Thus, using these conversion factors from spore counts to spore-OC and spore-mass, along with analytical data for arabitol or mannitol in filter samples, the contribution of fungal spores to the OC and to the mass balance of atmospheric aerosol particles can be estimated.

  12. MapMaker and PathTracer for tracking carbon in genome-scale metabolic models.

    Science.gov (United States)

    Tervo, Christopher J; Reed, Jennifer L

    2016-05-01

    Constraint-based reconstruction and analysis (COBRA) modeling results can be difficult to interpret given the large numbers of reactions in genome-scale models. While paths in metabolic networks can be found, existing methods are not easily combined with constraint-based approaches. To address this limitation, two tools (MapMaker and PathTracer) were developed to find paths (including cycles) between metabolites, where each step transfers carbon from reactant to product. MapMaker predicts carbon transfer maps (CTMs) between metabolites using only information on molecular formulae and reaction stoichiometry, effectively determining which reactants and products share carbon atoms. MapMaker correctly assigned CTMs for over 97% of the 2,251 reactions in an Escherichia coli metabolic model (iJO1366). Using CTMs as inputs, PathTracer finds paths between two metabolites. PathTracer was applied to iJO1366 to investigate the importance of using CTMs and COBRA constraints when enumerating paths, to find active and high flux paths in flux balance analysis (FBA) solutions, to identify paths for putrescine utilization, and to elucidate a potential CO2 fixation pathway in E. coli. These results illustrate how MapMaker and PathTracer can be used in combination with constraint-based models to identify feasible, active, and high flux paths between metabolites.

  13. Environmental variables and levels of exhaled carbon monoxide and carboxyhemoglobin in elderly people taking exercise.

    Science.gov (United States)

    Salicio, Marcos Adriano; Mana, Viviane Aparecida Martins; Fett, Waléria Christiane Rezende; Gomes, Luciano Teixeira; Botelho, Clovis

    2016-04-01

    This article aims to analyze levels of exhaled carbon monoxide, carboxyhemoglobinand cardiopulmonary variables in old people practicing exercise in external environments, and correlate them with climate and pollution factors. Temporal ecological study with118 active elderly people in the city of Cuiabá, in the state of Mato Grosso, Brazil. Data were obtained on use of medication, smoking, anthropometric measurements, spirometry, peak flow, oxygen saturation, heart rate, exhaled carbon monoxide, carboxyhemoglobin, climate, number of farm fires and pollution. Correlations were found between on the one hand environmental temperature, relative humidity of the air and number of farmers' fires, and on the other hand levels of carbon monoxide exhaled and carboxyhemoglobin (p elderly people, environmental factors influence levels of exhaled carbon monoxide, carboxyhemoglobin and heart rate. There is thus a need for these to be monitored during exercise. The use of a carbon monoxide monitor to evaluate exposure to pollutants is suggested.

  14. Final report of the TRUE Block Scale project. 2. Tracer tests in the block scale

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Peter; Byegaard, Johan [Geosigma AB, Uppsala (Sweden); Winberg, Anders [Conterra AB, Partille (Sweden)

    2002-05-01

    The tracer test programme of the TRUE Block Scale Project involved 14 tracer tests campaigns, including performance of 32 tracer injections in 16 different combinations of source and sink sections (flow paths) varying in length between 10 to 130 metres, and involving one or more structures. Average, travel times varied between 1.5 and >2000 hours. Tracer dilution tests performed in conjunction with cross-hole hydraulic pumping tests were found to be a very important part of the pre-tests, where the results were used to identify and screen among possible injection points, and to verify the hydrostructural model valid at a given time. The main problem faced in the block scale tests was to select a test geometry, which gave a sufficiently high mass recovery, and at the same time enabled performance of cross-hole sorbing tracer tests within reasonable time frames. Three different injection methods were applied during the test programme; decaying pulse, finite pulse and forced pulse (unequal dipole). During the later phases of the tracer test programme it was identified that forced injection had to be employed in order to enable detection of tracer at the sink due to strong dilution, and also to avoid problems with artificially induced tailing in the injection signal. Sorbing (reactive) tracers were selected among the radioactive isotopes of the alkali and alkaline earth metals previously used in the TRUE- 1 experiments. It was decided that at least one slightly sorbing tracer and one strongly sorbing tracer should be used in each injection. Non-sorbing tracers were used for conservative reference, e.g., {sup 82}Br{sup -}, {sup 186}ReO{sub 4}, HTO (tritiated water) and {sup 131}I{sup -}. In two of the injections the radioactive non-sorbing tracers were rather short-lived and Uranine and Naphthionate were used as complementary conservative tracers. Surface distribution coefficients, K{sub a}, were evaluated from TRUE-1 and TRUE Block Scale data, making use of the

  15. Natural and Artificial (fluorescent) Tracers to Characterise Hydrogeological Functioning and to Protect Karst Aquifers

    Science.gov (United States)

    Andreo, B.; Mudarra, M.; Marin, A. I.; Barberá, J. A.

    2012-12-01

    The hydrogeological functioning and response of karst aquifers can be determined by the joint use of natural hydrogeochemical tracers, especially total organic carbon (TOC) and intrinsic fluorescence of water, together with artificial (fluorescent) tracers, under the same hydrodynamic conditions. Sharp and rapid variations in discharge, temperature, electrical conductivity and water chemistry, particularly of natural tracers of infiltration (TOC, intrinsic fluorescence and NO3-) recorded in karst spring water, confirm the existence of well developed karst conduits in the sector of the aquifer being drained, with rapid flows and very short water transit times from the surface to the springs (Mudarra et al., 2011). This is in agreement with the evidence obtained from breakthrough curves of fluorescent dye tracers (uranine, eosine, etc.). However, time lags between maximum concentrations of natural (especially TOC and intrinsic fluorescence) and artificial tracers show that the global system response is faster than that produced from a recharge concentrated at a point on the surface, even in karst sinkholes. Response and transit times of water through the karst can be calculated using both natural and artificial tracers, but flow velocities can really only be quantified using artificial tracers. Analysis of the responses obtained by natural tracers of infiltration (global system response) and artificial tracers (single response) in karst waters has revealed the usefulness and complementarity of both techniques for characterising the hydrogeological functioning of karst aquifers and, even more important, for validating contamination vulnerability mapping in these medium (Zwahlen, 2004; Andreo et al., 2006). In recent decades, several methods have been developed for such vulnerability mapping, but little progress has been made in validating their results. This validation is essential for the adequate protection of water resources in karst media, as has been shown in

  16. A Review on Preferential Oxidation of Carbon Monoxide in Hydrogen Rich Gases

    Directory of Open Access Journals (Sweden)

    A. Mishra

    2011-05-01

    Full Text Available In this review, recent works on the preferential oxidation of carbon monoxide in hydrogen rich gases for fuel cell applications are summarized. H2 is used as a fuel for polymer-electrolyte membrane fuel cell (PEMFC. It is produced by reforming of natural gas or liquid fuels followed by water gas shift reaction. The produced gas consists of H2, CO, and CO2. In which CO content is around 1%, which is highly poisonous for the Pt anode of the PEMFC so that further removal of CO is needed. Catalytic preferential oxidation of CO (CO-PROX is one of the most suitable methods of purification of H2 because of high CO conversion rate at low temperature range, which is preferable for PEMFC operating conditions. Catalysts used for COPROX are mainly noble metal based; gold based and base metal oxide catalysts among them Copper-Ceria based catalysts are the most appropriate due to its low cost, easy availability and result obtained by these catalysts are comparable with the conventional noble metal catalysts. Copyright © 2011 BCREC UNDIP. All rights reserved(Received: 22nd October 2010, Revised: 12nd January 2011, Accepted: 19th January 2011[How to Cite: A. Mishra, R. Prasad. (2011. A Review on Preferential Oxidation of Carbon Monoxide in Hydrogen Rich Gases. Bulletin of Chemical Reaction Engineering & Catalysis, 6 (1: 1-14. doi:10.9767/bcrec.6.1.191.1-14][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.6.1.191.1-14 || or local:  http://ejournal.undip.ac.id/index.php/bcrec/article/view/191] | View in 

  17. Human umbilical cord blood mononuclear cell transplantation for delayed encephalopathy after carbon monoxide intoxication

    Directory of Open Access Journals (Sweden)

    Gong D

    2013-08-01

    Full Text Available Dianrong Gong,1 Haiyan Yu,1 Weihua Wang,2 Haixin Yang,1 Fabin Han1,21Department of Neurology, 2Centre for Stem Cells and Regenerative Medicine, Liaocheng People's Hospital, The Affiliated Liaocheng Hospital, Taishan Medical University, Shandong, People's Republic of ChinaAbstract: Stem cell transplantation is one of the potential treatments for neurological disorders. Since human umbilical cord stem cells have been shown to provide neuroprotection and promote neural regeneration, we have attempted to transplant the human umbilical cord blood mononuclear cells (hUCB-MNCs to treat patients with delayed encephalopathy after carbon monoxide intoxication (DEACOI. The hUCB-MNCs were isolated from fresh umbilical cord blood and were given to patients subarachnoidally. Physical examinations, mini-mental state examination scores, and computed tomography scans were used to evaluate the improvement of symptoms, signs, and pathological changes of the patient's brain before and after hUCB-MNC transplantation. A total of 12 patients with DEACOI were treated with hUCB-MNCs in this study. We found that most of the patients have shown significant improvements in movement, behavior, and cognitive function, and improved brain images in 1–4 months from the first transplantation of hUCB-MNCs. None of these patients have been observed to have any severe adverse effects. Our study suggests that the hUCB-MNC transplantation may be a safe and effective treatment for DEACOI. Further studies and clinical trials with more cases, using more systematic scoring methods, are needed to evaluate brain structural and functional improvements in patients with DEACOI after hUCB-MNC therapy.Keywords: human umbilical cord blood mononuclear cells, transplantation, delayed encephalopathy after carbon monoxide intoxication, MMSE

  18. Quantitative extraction of organic tracer compounds from ambient particulate matter collected on polymer substrates.

    Science.gov (United States)

    Sun, Qinyue; Alexandrova, Olga A; Herckes, Pierre; Allen, Jonathan O

    2009-05-15

    Organic compounds in ambient particulate matter (PM) samples are used as tracers for PM source apportionment. These PM samples are collected using high volume samplers; one such sampler is an impactor in which polyurethane foam (PUF) and polypropylene foam (PPF) are used as the substrates. The polymer substrates have the advantage of limiting particle bounce artifacts during sampling; however these substrates may contain background organic additives. A protocol of two extractions with isopropanol followed by three extractions with dichloromethane (DCM) was developed for both substrate precleaning and analyte extraction. Some residual organic contaminants were present after precleaning; expressed as concentrations in a 24-h ambient PM sample, the residual amounts were 1 microg m(-3) for plasticizers and antioxidants, and 10 ng m(-3) for n-alkanes with carbon number lower than 26. The quantification limit for all other organic tracer compounds was approximately 0.1 ng m(-3) in a 24-h ambient PM sample. Recovery experiments were done using NIST Standard Reference Material (SRM) Urban Dust (1649a); the average recoveries for polycyclic aromatic hydrocarbons (PAHs) from PPF and PUF substrates were 117+/-8% and 107+/-11%, respectively. Replicate extractions were also done using the ambient samples collected in Nogales, Arizona. The relative differences between repeat analyses were less than 10% for 47 organic tracer compounds quantified. After the first extraction of ambient samples, less than 7% of organic tracer compounds remained in the extracted substrates. This method can be used to quantify a suite of semi- and non-polar organic tracer compounds suitable for source apportionment studies in 24-h ambient PM samples.

  19. Effect of different emission inventories on modeled ozone and carbon monoxide in Southeast Asia

    Science.gov (United States)

    Amnuaylojaroen, T.; Barth, M. C.; Emmons, L. K.; Carmichael, G. R.; Kreasuwun, J.; Prasitwattanaseree, S.; Chantara, S.

    2014-12-01

    In order to improve our understanding of air quality in Southeast Asia, the anthropogenic emissions inventory must be well represented. In this work, we apply different anthropogenic emission inventories in the Weather Research and Forecasting Model with Chemistry (WRF-Chem) version 3.3 using Model for Ozone and Related Chemical Tracers (MOZART) gas-phase chemistry and Global Ozone Chemistry Aerosol Radiation and Transport (GOCART) aerosols to examine the differences in predicted carbon monoxide (CO) and ozone (O3) surface mixing ratios for Southeast Asia in March and December 2008. The anthropogenic emission inventories include the Reanalysis of the TROpospheric chemical composition (RETRO), the Intercontinental Chemical Transport Experiment-Phase B (INTEX-B), the MACCity emissions (adapted from the Monitoring Atmospheric Composition and Climate and megacity Zoom for the Environment projects), the Southeast Asia Composition, Cloud, Climate Coupling Regional Study (SEAC4RS) emissions, and a combination of MACCity and SEAC4RS emissions. Biomass-burning emissions are from the Fire Inventory from the National Center for Atmospheric Research (NCAR) (FINNv1) model. WRF-Chem reasonably predicts the 2 m temperature, 10 m wind, and precipitation. In general, surface CO is underpredicted by WRF-Chem while surface O3 is overpredicted. The NO2 tropospheric column predicted by WRF-Chem has the same magnitude as observations, but tends to underpredict the NO2 column over the equatorial ocean and near Indonesia. Simulations using different anthropogenic emissions produce only a slight variability of O3 and CO mixing ratios, while biomass-burning emissions add more variability. The different anthropogenic emissions differ by up to 30% in CO emissions, but O3 and CO mixing ratios averaged over the land areas of the model domain differ by ~4.5% and ~8%, respectively, among the simulations. Biomass-burning emissions create a substantial increase for both O3 and CO by ~29% and ~16

  20. Highly selective dry etching of polystyrene-poly(methyl methacrylate) block copolymer by gas pulsing carbon monoxide-based plasmas

    Science.gov (United States)

    Miyazoe, Hiroyuki; Jagtiani, Ashish V.; Tsai, Hsin-Yu; Engelmann, Sebastian U.; Joseph, Eric A.

    2017-05-01

    We propose a very selective PMMA removal method from poly(styrene-block-methyl methacrylate) (PS-b-PMMA) copolymer using gas pulsing cyclic etching. Flow ratio of hydrogen (H2) added to carbon monoxide (CO) plasma was periodically changed to control etch and deposition processes on PS. By controlling the process time of each etch and deposition step, full PMMA removal including etching of the neutral layer was demonstrated at 28 nm pitch, while PS thickness remained intact. This is more than 10 times higher etch selectivity than conventional continuous plasma etch processes using standard oxygen (O2), CO-H2 and CO-O2-based chemistries.

  1. Tracer diffusivity and effective temperature in bacterial suspensions

    CERN Document Server

    Patteson, Alison E; Purohit, Prashant K; Arratia, Paulo E

    2015-01-01

    The dynamics of tracer particles in \\textit{E. coli} suspensions are experimentally investigated as a function of particle size and bacteria concentration. We find that tracer diffusivity is enhanced due to particle-bacteria interactions and varies non-monotonically with particle size, exhibiting a peak at sizes comparable to the bacterial length. The time scale characterizing the transition from ballistic to diffusive regime increases monotonically with \\textit{E. coli} concentration and particle size. Diffusivity measurements are then used to estimate suspension effective temperature, which varies nonlinearly with tracer size, suggesting that measures of activity are probe size dependent.

  2. Radionuclide Tracers for Myocardial Perfusion Imaging and Blood Flow Quantification.

    Science.gov (United States)

    deKemp, Robert A; Renaud, Jennifer M; Klein, Ran; Beanlands, Rob S B

    2016-02-01

    Myocardial perfusion imaging is performed most commonly using Tc-99m-sestamibi or tetrofosmin SPECT as well as Rb-82-rubidium or N-13-ammonia PET. Diseased-to-normal tissue contrast is determined by the tracer retention fraction, which decreases nonlinearly with flow. Reduced tissue perfusion results in reduced tracer retention, but the severity of perfusion defects is typically underestimated by 20% to 40%. Compared to SPECT, retention of the PET tracers is more linearly related to flow, and therefore, the perfusion defects are measured more accurately using N-13-ammonia or Rb-82.

  3. Carbon monoxide expedites metabolic exhaustion to inhibit tumor growth.

    Science.gov (United States)

    Wegiel, Barbara; Gallo, David; Csizmadia, Eva; Harris, Clair; Belcher, John; Vercellotti, Gregory M; Penacho, Nuno; Seth, Pankaj; Sukhatme, Vikas; Ahmed, Asif; Pandolfi, Pier Paolo; Helczynski, Leszek; Bjartell, Anders; Persson, Jenny Liao; Otterbein, Leo E

    2013-12-01

    One classical feature of cancer cells is their metabolic acquisition of a highly glycolytic phenotype. Carbon monoxide (CO), one of the products of the cytoprotective molecule heme oxygenase-1 (HO-1) in cancer cells, has been implicated in carcinogenesis and therapeutic resistance. However, the functional contributions of CO and HO-1 to these processes are poorly defined. In human prostate cancers, we found that HO-1 was nuclear localized in malignant cells, with low enzymatic activity in moderately differentiated tumors correlating with relatively worse clinical outcomes. Exposure to CO sensitized prostate cancer cells but not normal cells to chemotherapy, with growth arrest and apoptosis induced in vivo in part through mitotic catastrophe. CO targeted mitochondria activity in cancer cells as evidenced by higher oxygen consumption, free radical generation, and mitochondrial collapse. Collectively, our findings indicated that CO transiently induces an anti-Warburg effect by rapidly fueling cancer cell bioenergetics, ultimately resulting in metabolic exhaustion.

  4. The effect of carbon monoxide on planetary haze formation

    Energy Technology Data Exchange (ETDEWEB)

    Hörst, S. M.; Tolbert, M. A, E-mail: sarah.horst@colorado.edu [Cooperative Institute for Research in Environmental Sciences, University of Colorado, Boulder, CO (United States)

    2014-01-20

    Organic haze plays a key role in many planetary processes ranging from influencing the radiation budget of an atmosphere to serving as a source of prebiotic molecules on the surface. Numerous experiments have investigated the aerosols produced by exposing mixtures of N{sub 2}/CH{sub 4} to a variety of energy sources. However, many N{sub 2}/CH{sub 4} atmospheres in both our solar system and extrasolar planetary systems also contain carbon monoxide (CO). We have conducted a series of atmosphere simulation experiments to investigate the effect of CO on the formation and particle size of planetary haze analogues for a range of CO mixing ratios using two different energy sources, spark discharge and UV. We find that CO strongly affects both number density and particle size of the aerosols produced in our experiments and indicates that CO may play an important, previously unexplored, role in aerosol chemistry in planetary atmospheres.

  5. Prevention of carbon monoxide exposure in general and recreational aviation.

    Science.gov (United States)

    Zelnick, Sanford D; Lischak, Michael W; Young, David G; Massa, Thomas V

    2002-08-01

    Carbon monoxide exposure is an important public health issue that poses a significant, albeit uncommon risk in aviation. Exposure is most common in single engine piston-driven aircraft where air is passed over the exhaust manifold to serve as cabin heat. Effective primary prevention of this exposure is the regular inspection and maintenance of aircraft exhaust systems, as required by law. For situations at special risk should exposure occur, and where there is concern for the public safety, installation of active warning devices for CO intrusion into cockpits may improve secondary prevention. Modern studies should be performed of occupation-specific abilities to support the 50 ppm FAA CO exposure standard and 50-70 ppm FAA Technical Standard Order (TSO) for CO monitors alerting pilots to the possibility of exhaust gas intrusion into their cockpits.

  6. Terahertz Time Domain Gas-phase Spectroscopy of Carbon Monoxide

    Science.gov (United States)

    Kilcullen, Patrick; Hartley, I. D.; Jensen, E. T.; Reid, M.

    2015-04-01

    Free induction decay signals emitted from Carbon Monoxide (CO) excited by sub-picosecond pulses of Terahertz (THz) radiation are directly measured in the time domain and compared to model calculations using a linear dispersion model to good agreement. Best fitting techniques of the data using the model allow the self-pressure broadening of CO to be measured across a range of absolute pressures, and the rotational constant to be determined. We find B V = 5.770 ± 0.003 × 1010 Hz in agreement with previous measurements. A partial pressure limit of detection for CO of 7900 ppm is estimated at atmosphere through extrapolating the calculated commensurate echo peaks down to low pressures with respect to the RMS noise floor of our THz time domain spectroscopy (THz-TDS) apparatus, which implies a limit of detection in the range of 40 ppm for commercial THz-TDS systems.

  7. An Unusual Cause of Supraventricular Tachycardia: Acute Carbon Monoxide Poisoning

    Directory of Open Access Journals (Sweden)

    Suat Zengin

    2014-03-01

    Full Text Available      Carbon monoxide (CO is a toxic gas produced by the incomplete combustion of carbon-containing compounds. Exposure to high concentrations of CO can be letha and is the most common cause of death from poisoning worldwide. Cardiac manifestations after exposure to CO, including myocardial ischemia, heart failure, and arrhythmias, have been reported. A 28-year-old a patient was admitted to our emergency department with altered consciousness as a consequence of acute domestic exposure to CO from a stove. His carboxyhemoglobin level was 39%. The oxygen treatment was started promptly, and therapeutic red cell exchange was performed. An electrocardiogram revealed supraventricular tachycardia (SVT, and an echocardiographic examination demonstrated normal cardiac functions. To the best of our knowledge, this study is the second to report a case of SVT attack due to acute CO intoxication. This paper discusses the management of this complication in patients poisoned with CO.

  8. Design and analysis of a natural-gradient ground-water tracer test in a freshwater tidal wetland, West Branch Canal Creek, Aberdeen Proving Ground, Maryland

    Science.gov (United States)

    Olsen, Lisa D.; Tenbus, Frederick J.

    2005-01-01

    each, from July 1998 through September 1999, to assess background conditions and monitor tracer movement. During the test, 644 samples were analyzed for fluorescein, 617 samples were analyzed for bromide with an ion-selective electrode, 213 samples were analyzed for bromide with colorimetric methods, and 603 samples were analyzed for sulfur hexafluoride, including samples collected prior to tracer injection to determine background concentrations. Additional samples were analyzed for volatile organic compounds (96 samples) and methane (37 samples) to determine the distribution of these contaminants and the extent of methanogenic conditions within the tracer array; however, these data were not used for the analysis of the test. During the tracer test, the fluorescein dye, bromide, and sulfur hexafluoride were transported predominantly in the upward direction, although all three tracers also moved outward in all directions from the injection point, and it is likely that some tracer mass moved beyond the lateral edges of the array. An analysis of the tracer-test data was performed through the use of breakthrough curves and isoconcentration contour plots. Results show that movement of the fluorescein dye, a non-conservative tracer, was retarded compared to the other two tracers, likely as a result of sorption onto the wetland sediments. Suspected loss of tracer mass along the lateral edges of the array prevented a straightforward quantitative analysis of tracer transport and ground-water velocity from the bromide and sulfur-hexafluoride data. In addition, the initial density of the bromide/sulfur hexafluoride solution (calculated to be 1.097 grams per milli2 Ground-Water Tracer Test, West Branch Canal Creek, Aberdeen Proving Ground, MD liter) could have caused the solution to sink below the injection point before undergoing dilution and moving back up into the array. For these reasons, the data analysis in this report was performed largely through qualitative method

  9. Small Molecule PET Tracers in Drug Discovery.

    Science.gov (United States)

    Donnelly, David J

    2017-09-01

    The process of discovering and developing a new pharmaceutical is a long, difficult, and risky process that requires numerous resources. Molecular imaging techniques such as PET have recently become a useful tool for making decisions along a drug candidate's development timeline. PET is a translational, noninvasive imaging technique that provides quantitative information about a potential drug candidate and its target at the molecular level. Using this technique provides decisional information to ensure that the right drug candidate is being chosen, for the right target, at the right dose within the right patient population. This review will focus on small molecule PET tracers and how they are used within the drug discovery process. PET provides key information about a drug candidate's pharmacokinetic and pharmacodynamic properties in both preclinical and clinical studies. PET is being used in all phases of the drug discovery and development process, and the goal of these studies are to accelerate the process in which drugs are developed. Copyright © 2017. Published by Elsevier Inc.

  10. National Biomedical Tracer Facility: Project definition study

    Energy Technology Data Exchange (ETDEWEB)

    Heaton, R.; Peterson, E. [Los Alamos National Lab., NM (United States); Smith, P. [Smith (P.A.) Concepts and Designs (United States)

    1995-05-31

    The Los Alamos National Laboratory is an ideal institution and New Mexico is an ideal location for siting the National Biomedical Tracer Facility (NBTF). The essence of the Los Alamos proposal is the development of two complementary irradiation facilities that combined with our existing radiochemical processing hot cell facilities and waste handling and disposal facilities provide a low cost alternative to other proposals that seek to satisfy the objectives of the NBTF. We propose the construction of a 30 MeV cyclotron facility at the site of the radiochemical facilities, and the construction of a 100 MeV target station at LAMPF to satisfy the requirements and objectives of the NBTF. We do not require any modifications to our existing radiochemical processing hot cell facilities or our waste treatment and disposal facilities to accomplish the objectives of the NBTF. The total capital cost for the facility defined by the project definition study is $15.2 M. This cost estimate includes $9.9 M for the cyclotron and associated facility, $2.0 M for the 100 MeV target station at LAMPF, and $3.3 M for design.

  11. TRACER STUDY OF RTU GRADUATES: AN ANALYSIS

    Directory of Open Access Journals (Sweden)

    Thelma L. Ramirez

    2014-01-01

    Full Text Available This paper aimed to determine if the field of specialization in the different colleges of RTU graduates and their academic-acquired skills and competencies are related to their present occupations. A modified Graduate Tracer Study (GTS instrument was utilized to gather the quantitative data. Out of 500 questionnaires administered, there were 250 graduates returned answered questionnaires representing the three Colleges: Education, Arts and Sciences, Business and Entrepreneurial Technology. A face to face interview was also conducted in order to support the gathered data. The SPSS was used to generate results from the acquired quantitative data using the frequency counts, percentage and the Chi-square goodness of fit test. The findings revealed that the graduates claimed that their knowledge, academic-acquired skills and competencies contributed greatly in their job performance. The Chi-square goodness of fit proved that there is a significant relationship between the graduates’ fields of specialization and their occupations after graduation. Likewise, the academic-acquired skills and competencies of the graduates are relevant to their chosen occupations. The results further proved that RTU produces marketable and appropriately trained graduates with the majority landing in course-related jobs within a short period after graduation. The study also indicates that the RTU graduates possess the skills and competencies necessary to succeed in this competitive world. However eexpansion of tie-ups with private business entities is made to at least maintain the high employability level of the graduates.

  12. Analysis of the migration characteristics of tracers in a heterogeneous flow field through a natural fracture of a domestic granite

    Energy Technology Data Exchange (ETDEWEB)

    Kum, Y. S.; Park, J. K.; Han, P. S. [KAERI, Taejon (Korea, Republic of)

    2001-05-01

    Tracers migration experiment was performed in a natural fracture of a domestic granite. The scale of rock fracture was 100x60x40(cm). In order to observe the migration characteristics, two kinds of nonsorbing tracers were used; as high molecular organic dyes, Eosine, and NaLS, and as anions, Bromide and Chloride. Tracers was injected in a borehole as a band funtion and collected at the opposite borehole. A variable aperture channel model with particle tracking method was used to characterize the aperture width of the fracture and to simulate solute transport. The heterogeneous flow field was modeled by a variable aperture channel model after characterizing aperture distribution by hydraulic tests through boreholes. The particle tracking method applied effectively in simulating tracers transport through a heterogeneous flow field in the rock fracture. Simulated results show that tracers do not migrate through the shortest straight line between inlet and outlet, but migrate through the paths having lowest flow resistance. that is channeling flow.

  13. pH dependence and unsuitability of fluorescein dye as a tracer for pesticide mobility studies in acid soil

    Science.gov (United States)

    Chris Peterson

    2009-01-01

    The mobility of fluorescein and bromide used as tracers in packed soil columns was investigated.Five different soils were used in two application methods: soil surface application and soil incorporation, both of which simulate accepted methods of soil application of termiticides to prevent structural infestation. The...

  14. Kinetic analysis of 18F-fluorodihydrorotenone as a deposited myocardial flow tracer: Comparison to thallium-201.

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, Robert C.; Powers-Risius, Patricia; Reutter, Bryan W.; O' Neil, James P.; La Belle, Michael; Huesman, Ronald H.; VanBrocklin, Henry F.

    2004-03-01

    The goal of this investigation was to assess the accuracy of 18F-fluorodihydrorotenone (18F-FDHR) as a new deposited myocardial flow tracer and compare the results to those for 201Tl. Methods. The kinetics of these flow tracers were evaluated in 22 isolated, erythrocyte- and albumin-perfused rabbit hearts over a flow range encountered in patients. The two flow tracers plus a vascular reference tracer (131I-albumin) were introduced as a bolus through a port just above the aortic cannula. Myocardial extraction, retention, washout, and uptake parameters were computed from the venous outflow curves using the multiple indicator dilution technique and spectral analysis. Results. The mean initial extraction fractions of 18F-FDHR (0.85 +- 0.07) and 201Tl (0.87 +- 0.05) were not significantly different, although the initial extraction fraction for 18F-FDHR declined with flow (P < 0.0001), whereas the initial extraction fraction of 201Tl did not. Washout of 201Tl was faster (P < 0.001) and more affected by flow (P < 0.05) than 18F-FDHR washout. Except for initial extraction fraction, 18F-FDHR retention was greater (P < 0.001) and less affected by flow (P < 0.05) than 201Tl retention. Reflecting its superior retention, net uptake of 18F-FDHR was better correlated with flow than 201Tl uptake at both one and fifteen minutes after tracer introduction (P < 0.0001 for both comparisons). Conclusion. The superior correlation of 18F-FDHR uptake with flow indicates that it is a better flow tracer than 201Tl in the isolated rabbit heart. Compared to the other currently available positron-emitting flow tracers (82Rb, 13N-ammonia, and 15O-water), 18F-FDHR has the potential of providing excellent image resolution without the need for an on-site cyclotron.

  15. Estimation of time-variable fast flow path chemical concentrations for application in tracer-based hydrograph separation analyses

    Science.gov (United States)

    Kronholm, Scott C.; Capel, Paul D.

    2016-09-01

    Mixing models are a commonly used method for hydrograph separation, but can be hindered by the subjective choice of the end-member tracer concentrations. This work tests a new variant of mixing model that uses high-frequency measures of two tracers and streamflow to separate total streamflow into water from slowflow and fastflow sources. The ratio between the concentrations of the two tracers is used to create a time-variable estimate of the concentration of each tracer in the fastflow end-member. Multiple synthetic data sets, and data from two hydrologically diverse streams, are used to test the performance and limitations of the new model (two-tracer ratio-based mixing model: TRaMM). When applied to the synthetic streams under many different scenarios, the TRaMM produces results that were reasonable approximations of the actual values of fastflow discharge (±0.1% of maximum fastflow) and fastflow tracer concentrations (±9.5% and ±16% of maximum fastflow nitrate concentration and specific conductance, respectively). With real stream data, the TRaMM produces high-frequency estimates of slowflow and fastflow discharge that align with expectations for each stream based on their respective hydrologic settings. The use of two tracers with the TRaMM provides an innovative and objective approach for estimating high-frequency fastflow concentrations and contributions of fastflow water to the stream. This provides useful information for tracking chemical movement to streams and allows for better selection and implementation of water quality management strategies.

  16. The Effect of the Hayward Corridor Improvement Project on Carbon Monoxide Emission

    Science.gov (United States)

    Muhlfelder, M.; Martinez, E.; Maestas, A.; Peek, A.

    2013-12-01

    In August of 2010, construction began on a stretch of road in Downtown Hayward to address a problem with traffic flow. Known as the Hayward Corridor, the project reshaped the flow of traffic, replacing the two way streets of Foothill, Mission, and A Street with a loop between them. This project began with the initiative of reducing congestion in this area and improving access to businesses for pedestrians. The project was expected to have little environmental impact in most common assessments of degree of effect, including particulate matter, ozone and carbon monoxide levels. This report will discuss the effect of the Hayward Corridor Improvement Project on carbon monoxide emission. Data available to the public in the project's Environmental Impact Report shows that carbon monoxide levels before construction began were at an acceptable level according to federal and state standards. Projections for future concentrations both with and without the project show a decrease in carbon monoxide levels due to technological improvements and the gradual replacement of older, less efficient vehicles. The Environmental Impact Report projected that there would be little difference in carbon monoxide levels whether the project took place or not, at an average of 1.67x102 fewer parts per million per 1 hour period of measurement emitted in the case of the project not taking place. While it is not possible to draw a conclusion on what the current carbon monoxide levels would be if the project had not taken place due to the changes in traffic flow and other surrounding roads as a result of the project, the data gathered in June of 2013 suggested that carbon monoxide levels are higher than the values projected in 2007. This report summarizes both the accuracy of these carbon monoxide level projections and the effect of construction on carbon monoxide levels in the Hayward Corridor and the surrounding area.

  17. Plutonium as a tracer for soil erosion assessment in northeast China

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Yihong [School of Geographic and Oceanographic Sciences, Nanjing University, Nanjing 210023 (China); Qiao, Jixin [Center for Nuclear Technologies, Technical University of Denmark, Risø Campus, DK-4000 Roskilde (Denmark); Pan, Shaoming, E-mail: span@nju.edu.cn [School of Geographic and Oceanographic Sciences, Nanjing University, Nanjing 210023 (China); Hou, Xiaolin, E-mail: xiho@dtu.dk [Center for Nuclear Technologies, Technical University of Denmark, Risø Campus, DK-4000 Roskilde (Denmark); Xi' an AMS Center, SKLLQG, Institute of Earth Environment, CAS, Xi' an 710075 (China); Roos, Per [Center for Nuclear Technologies, Technical University of Denmark, Risø Campus, DK-4000 Roskilde (Denmark); Cao, Liguo [School of Geographic and Oceanographic Sciences, Nanjing University, Nanjing 210023 (China)

    2015-04-01

    Soil erosion is one of the most serious environmental and agricultural problems faced by human society. Assessing intensity is an important issue for controlling soil erosion and improving eco-environmental quality. The suitability of the application of plutonium (Pu) as a tracer for soil erosion assessment in northeast China was investigated by comparing with that of {sup 137}Cs. Here we build on preliminary work, in which we investigated the potential of Pu as a soil erosion tracer by sampling additional reference sites and potential erosive sites, along the Liaodong Bay region in northeast China, for Pu isotopes and {sup 137}Cs. {sup 240}Pu/{sup 239}Pu atomic ratios in all samples were approximately 0.18, which indicated that the dominant source of Pu was the global fallout. Pu showed very similar distribution patterns to those of {sup 137}Cs at both uncultivated and cultivated sites. {sup 239+240}Pu concentrations in all uncultivated soil cores followed an exponential decline with soil depth, whereas at cultivated sites, Pu was homogenously distributed in plow horizons. Factors such as planted crop types, as well as methods and frequencies of irrigation and tillage were suggested to influence the distribution of radionuclides in cultivated land. The baseline inventories of {sup 239+240}Pu and {sup 137}Cs were 88.4 and 1688 Bq m{sup −2} respectively. Soil erosion rates estimated by {sup 239+240}Pu tracing method were consistent with those obtained by the {sup 137}Cs method, confirming that Pu is an effective tracer with a similar tracing behavior to that of {sup 137}Cs for soil erosion assessment. - Highlights: • The potential for the use of Pu as a soil erosion tracer was investigated. • Pu would be a good tracer given its long half-life. • Depth profiles of Pu in soils were systematically studied and compared to {sup 137}Cs. • Pu is an effective soil erosion tracer with behavior similar to that of {sup 137}Cs. • Thus, Pu provides a means of

  18. A new multi-tracer transport scheme for the dynamical core of NCAR's Community Atmosphere Model

    Science.gov (United States)

    Erath, C.

    2012-04-01

    The integration of a conservative semi-Lagrangian multi-tracer transport scheme (CSLAM) in NCAR's High-Order Method Modeling Environment (HOMME) is considered here. HOMME is a highly scalable atmospheric modeling framework, and its current horizontal discretization relies on spectral element (SE) and/or discontinuous Galerkin (DG) methods on the cubed-sphere. It is one dynamical core of NCAR's Community Atmosphere Model (CAM). The main advantage of CSLAM is that the upstream cell (trajectories) information and computation of weights of integrals can be reused for each additional tracer. This makes CSLAM particularly interesting for global atmospheric modeling with growing number of tracers, e.g. more than 100 tracers for the chemistry version of CAM. An algorithm specifically designed for multiple processors and on the cubed-sphere grid for CSLAM in HOMME is a challenging task. HOMME is running on an element ansatz on the six cube faces. Inside these elements we create an Eulerian finite volume grid of equiangular gnomonic type, which represents the arrival grid in the scheme. But CSLAM relies on backward trajectories, which entails a departure grid. That means departure and arrival grid don't necessary have to be on the same element and certainly not on the same cube face. Also the reconstruction for higher order modeling needs a patch of tracer values which extend the element. Here we consider a third order reconstruction method. Therefore, we introduce a halo for the tracer values in the cell centers of a cube-element. The size of this halo depends on the Courant number (CFL condition) and the reconstruction type. Note that for a third order scheme and CFL number communication can be limited to one per time step. This data structure allows us to consider an element with its halo as one task where we have to be extra carful for elements which share a cube edge due to projection and orientation reasons. We stress that the reconstruction coefficients for elements

  19. Improved Ozone and Carbon Monoxide Profile Retrievals Using Multispectral Measurements from NASA "A Train", NPP, and TROPOMI Satellites

    Science.gov (United States)

    Fu, D.; Bowman, K. W.; Kulawik, S. S.; Miyazaki, K.; Worden, J. R.; Worden, H. M.; Livesey, N. J.; Payne, V.; Luo, M.; Natraj, V.; Veefkind, P.; Aben, I.; Landgraf, J.; Flynn, L. E.; Han, Y.; Liu, X.; Strow, L. L.; Kuai, L.

    2015-12-01

    Tropospheric ozone is at the juncture of air quality and climate. Ozone directly impacts human and plant health, and directly forces the climate system through absorption of thermal radiation. Carbon monoxide is a chemical precursor of greenhouse gases CO2 and tropospheric O3, and is also an ideal tracer of transport processes due to its medium life time (weeks to months). The Aqua-AIRS and Aura-OMI instruments in the NASA "A-Train", CrIS and OMPS instruments on the NOAA Suomi-NPP, IASI and GOME-2 on METOP and TROPOMI aboard the Sentinel 5 precursor (S5p) have the potential to provide the synoptic chemical and dynamical context for ozone necessary to quantify long-range transport at global scales and to provide an anchor to the near-term constellation of geostationary sounders: NASA TEMPO, ESA Sentinel 4, and the Korean GEMS. We introduce the JPL MUlti-SpEctral, MUlti-SpEcies, MUlti-SatEllite (MUSES) retrieval algorithm, which ingests panspectral observations across multiple platforms in a non-linear optimal estimation framework. MUSES incorporates advances in remote sensing science developed during the EOS-Aura era including rigorous error analysis diagnostics and observation operators needed for trend analysis, climate model evaluation, and data assimilation. Its performance has been demonstrated through prototype studies for multi-satellite missions (AIRS, CrIS, TROPOMI, TES, OMI, and OMPS). We present joint tropospheric ozone retrievals from AIRS/OMI and CrIS/OMPS over global scales, and demonstrate the potential of joint carbon monoxide profiles from TROPOMI/CrIS. These results indicate that ozone can be retrieved with ~2 degrees of freedom for signal (dofs) in the troposphere, which is similar to TES. Joint CO profiles have dofs similar to the MOPITT multispectral retrieval but with higher spatial resolution and coverage. Consequently, multispectral retrievals show promise in providing continuity with NASA EOS observations and pave the way towards a new

  20. What can environmental tracer concentrations tell us about groundwater residence time?

    Science.gov (United States)

    McCallum, J. L.; Engdahl, N. B.; Cook, P. G.; Simmons, C.

    2013-12-01

    Quantification of groundwater age distributions through the use on lumped parameter models and environmental tracer concentrations is an ongoing practice. These models are based on simple geometries and sampling conditions and may not be applicable outside of ideal conditions, limiting the results that can be obtained. We have developed a method that requires no underlying assumptions about the structure of the groundwater age distribution. This method assumes that the convolution relationship describes the relationship between temporal atmospheric concentrations and measured groundwater sample concentrations. We looked at synthetically generated groundwater age distributions and a number of levels of tracer data including a long time series of tritium, the use of CFCs and SF6 sampled at various times and the use of CFCs, SF6, 3H and 14C sampled at a single time. In general, we found that environmental tracers are not very informative of groundwater age distributions resulting in estimates being highly non-unique. The exception was the use of a time series of tritium data. Tritium is more informative due to the temporal variations of atmospheric concentrations and a short half-life reducing the correlation of sequential measurements. The ability of CFC compounds to estimate entire distributions was limited due to the lack of variation in temporal atmospheric concentrations and correlation between sampled concentrations. Despite varying ability of the method to predict whole distributions, some indicators such as the mean age and some arrival time statistics were estimated well by the method. The implications of this show that care should be taken in the choice of lumped parameter model used in conjunction with environmental tracer techniques to constrain entire groundwater age distributions. Interestingly, the ability to correct for mixing bias of mean ages despite poor estimates of entire groundwater age distributions shows some promise.

  1. Adsorption of nitrogen and carbon monoxide on clinoptilolite: determination and prediction of pure and binary isotherms

    Energy Technology Data Exchange (ETDEWEB)

    Triebe, R.W.; Tezel, F.H. [University of Ottawa, Ottawa, ON (Canada). Department of Chemical Engineering

    1995-10-01

    The adsorption of carbon monoxide and nitrogen on clinoptilolite is studied to determine the natural zeolite`s potential for air purification. Pure and binary isotherms were determined for nitrogen and carbon monoxide on a natural Turkish clinoptilolite under near ambient conditions. Experimentally determined isotherms are compared to predictions based on various models from the literature. The Wilson form of the Vacancy Solution Theory is the only model that provides reasonable agreement with the binary isotherm. Clinoptilolite is concluded to be a promising sorbent for separation of carbon monoxide and nitrogen. 30 refs., 11 figs., 5 tabs.

  2. West Twin Creek Alaska Subsurface Bromide Tracer Experiment, 2015

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This data was produced as part of a subsurface tracer experiment performed on a boreal hillslope in July, 2015. The data is separated into three files: 'Well...

  3. Microfluidics for Synthesis of Peptide-Based PET Tracers

    Directory of Open Access Journals (Sweden)

    Yang Liu

    2013-01-01

    Full Text Available Positron emission tomography (PET is a powerful noninvasive tool for acquisition of the physiological parameters in human and animals with the help of PET tracers. Among all the PET tracers, radiolabeled peptides have been widely explored for cancer-related receptor imaging due to their high affinity and specificity to receptors. But radiochemistry procedures for production of peptide-based PET tracers are usually complex, which makes large-scale clinical studies relatively challenging. New radiolabeling technologies which could simplify synthesis and purification procedures, are extremely needed. Over the last decade, microfluidics and lab-on-a-chip (LOC technology have boomed as powerful tools in the field of organic chemistry, which potentially provide significant help to the PET chemistry. In this minireview, microfluidic radiolabeling technology is described and its application for synthesis of peptide-based PET tracers is summarized and discussed.

  4. Chlorine isotopes potential as geo-chemical tracers

    Digital Repository Service at National Institute of Oceanography (India)

    Shirodkar, P.V.; Pradhan, U.K.; Banerjee, R.

    The potential of chlorine isotopes as tracers of geo-chemical processes of earth and the oceans is highlighted based on systematic studies carried out in understanding the chlorine isotope fractionation mechanism, its constancy in seawater and its...

  5. Tracking thermal fronts with temperature-sensitive, chemically reactive tracers

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, B.A.; Birdsell, S.A.

    1987-01-01

    Los Alamos is developing tracer techniques using reactive chemicals to track thermal fronts in fractured geothermal reservoirs. If a nonadsorbing tracer flowing from the injection to production well chemically reacts, its reaction rate will be a strong function of temperature. Thus the extent of chemical reaction will be greatest early in the lifetime of the system, and less as the thermal front progresses from the injection to production well. Early laboratory experiments identified tracers with chemical kinetics suitable for reservoirs in the temperature range of 75 to 100/sup 0/C. Recent kinetics studies have focused on the kinetics of hydrolysis of derivatives of bromobenzene. This class of reactions can be used in reservoirs ranging in temperature from 150 to 275/sup 0/C, which is of greater interest to the geothermal industry. Future studies will include laboratory adsorption experiments to identify possibly unwanted adsorption on granite, development of sensitive analytical techniques, and a field demonstration of the reactive tracer concept.

  6. Assessment of Halon-1301 as a groundwater age tracer

    OpenAIRE

    M. Beyer; R. van der Raaij; U. Morgenstern; Jackson, B.(Department of Physics, University of Pennsylvania, Philadelphia, PA, United States)

    2015-01-01

    Groundwater dating is an important tool to assess groundwater resources in regards to their dynamics, i.e. direction and timescale of groundwater flow and recharge, contamination risks and manage remediation. To infer groundwater age information, a combination of different environmental tracers, such as tritium and SF6, are commonly used. However, ambiguous age interpretations are often faced, due to a limited set of available tracers and their individual restricted applicat...

  7. Assessment of Halon-1301 as a groundwater age tracer

    OpenAIRE

    M. Beyer; R. van der Raaij; U. Morgenstern; Jackson, B.(Department of Physics, University of Pennsylvania, Philadelphia, PA, United States)

    2015-01-01

    Groundwater dating is an important tool to assess groundwater resources in regards to their dynamics, i.e. direction and time scale of groundwater flow and recharge, to assess contamination risks and manage remediation. To infer groundwater age information, a combination of different environmental tracers, such as tritium and SF6, are commonly used. However, ambiguous age interpretations are often faced, due to a limited set of available tracers and their in...

  8. Mobility of Metal Tracers in Unsaturated Tuffs of Busted Butte

    Science.gov (United States)

    Groffman, A. R.

    2001-12-01

    A complex tracer mixture was injected continuously for over two years into a 10 m x 10 m x 7 m block of unsaturated tuff as part of the Busted Butte unsaturated-zone tracer test at Yucca Mountain. The test was designed to measure tracer transport within the Topopah Springs and Calico Hills tuffs, units that occur between the potential high-level nuclear waste repository at Yucca Mountain and the water table below. The mixture included nonreactive (Br, I, and fluorinated benzoic acids (FBAs)) and reactive tracers (Li, Ce, Sm, Ni, Co, and Mn). Bromide, I, FBAs, and Li were detected during the test on absorbent pads emplaced in a series of solute collection boreholes located beneath the injectors but the more strongly sorbing metals did not reach the collection boreholes during this period. To determine the distribution and mobility of these metals, tracer constituents were extracted from tuff samples collected during overcoring and mineback of the test block. Tracers were extracted from the tuff samples by leaching with a 5% nitric acid solution for metals and a bicarbonate-carbonate buffer for anions. Results from the overcore sample suite show that metals have migrated through the tuff in the region adjacent to and immediately below the tracer injectors. Consistent with laboratory sorption measurements and observed breakthrough in the collection boreholes, rock analyses showed that Li is the most mobile of the metals. Co and Ni behave similarly, traveling tens of cm from the injection sites, while Sm and Ce moved far less, possibly due to precipitation reactions in addition to sorption. Determination of Mn transport is complicated by high background concentrations in the tuff; additional background samples are currently being evaluated. As expected, our rock analyses show that the nonreactive tracers Br and FBAs have moved beyond the overcore region, corroborating results from collection boreholes.

  9. Tracer dispersion in a percolation network with spatial correlations

    Science.gov (United States)

    Makse; Andrade; Eugene Stanley H

    2000-01-01

    We analyze the transport properties of a neutral tracer in a carrier fluid flowing through percolationlike porous media with spatial correlations. We model convection in the mass transport process using the velocity field obtained by the numerical solution of the Navier-Stokes and continuity equations in the pore space. We find that the resulting statistical properties of the tracer show a transition from a subdiffusion regime at low Peclet number to an enhanced diffusion regime at high Peclet number.

  10. Tensor anisotropy as a tracer of cosmic voids

    CERN Document Server

    Bustamante, Sebastian

    2015-01-01

    We present a new method to find voids in cosmological simulations based on the tidal and the velocity shear tensors definitions of the cosmic web. We use the fractional anisotropy (FA) computed from the eigenvalues of each web scheme as a void tracer. We identify voids using a watershed transform based on the local minima of the FA field without making any assumption on the shape or structure of the voids. We test the method on the Bolshoi simulation and report on the abundance and radial averaged profiles for the density, velocity and fractional anisotropy. We find that voids in the velocity shear web are smaller than voids in the tidal web, with a particular overabundance of very small voids in the inner region of filaments/sheets. We classify voids as subcompensated/overcompansated depending on the absence/presence of an overdense matter ridge in their density profile, finding that close to $65\\%$ and $35\\%$ of the total population are classified into each category, respectively. Finally, we find evidence ...

  11. A thermodynamic view of tracer plume evolution: Complete mixing condition evaluation

    Directory of Open Access Journals (Sweden)

    Constain A.

    2013-05-01

    Full Text Available One of most controversial issues of modern tracer theory is the “complete mixing condition” because of its importance in evolution of hazardous solutes in natural flows. This condition named also as “Mixing length” measures the distance from pouring point when tracer particles have spread uniformly on cross section of stream. The point is that until now there is no rational, complete and easy to use formula to calculate it. Rather, this condition is evaluated mostly by means of empirical relationships; among them Ruthven's is one of current usage. Also there are statistical methods that applied by software packages allow to characterize this condition. However a new focus on this issue is important, because is necessary to tie together, generality, easiness and accuracy. This paper puts on discussion a thermodynamics method to understand when a tracer is in this remarkable condition. Herein it is developed the conditions when this method may be applied. It is shown also how the resulting formula is convergent with Ruthven's equation. An experimental demonstration is presented.

  12. Small Molecule PET Tracers for Transporter Imaging.

    Science.gov (United States)

    Kilbourn, Michael R

    2017-09-01

    As the field of PET has expanded and an ever-increasing number and variety of compounds have been radiolabeled as potential in vivo tracers of biochemistry, transporters have become important primary targets or facilitators of radiotracer uptake and distribution. A transporter can be the primary target through the development of a specific high-affinity radioligand: examples are the multiple high-affinity radioligands for the neuronal membrane neurotransmitter or vesicular transporters, used to image nerve terminals in the brain. The goal of a radiotracer might be to study the function of a transporter through the use of a radiolabeled substrate, such as the application of 3-O-[(11)C]methyl]glucose to measure rates of glucose transport through the blood-brain barrier. In many cases, transporters are required for radiotracer distributions, but the targeted biochemistries might be unrelated: an example is the use of 2-deoxy-2-[(18)F]FDG for imaging glucose metabolism, where initial passage of the radiotracer through cell membranes requires the action of specific glucose transporters. Finally, there are transporters such as p-glycoprotein that function to extrude small molecules from tissues, and can effectively work against successful uptake of radiotracers. The diversity of structures and functions of transporters, their importance in human health and disease, and their role in therapeutic drug disposition suggest that in vivo imaging of transporter location and function will continue to be a point of emphasis in PET radiopharmaceutical development. In this review, the variety of transporters and their importance for in vivo PET radiotracer development and application are discussed. Transporters have thus joined the other major protein targets such as G-protein coupled receptors, ligand-gated ion channels, enzymes, and aggregated proteins as of high interest for understanding human health and disease. Copyright © 2017 Elsevier Inc. All rights reserved.

  13. Fourier analysis of multi-tracer cosmological surveys

    CERN Document Server

    Abramo, L Raul; Loureiro, Arthur

    2015-01-01

    We present optimal quadratic estimators for the Fourier analysis of cosmological surveys that detect several different types of tracers of large-scale structure. Our estimators can be used to simultaneously fit the matter power spectrum and the biases of the tracers - as well as redshift-space distortions (RSDs), non-Gaussianities (NGs), or any other effects that are manifested through differences between the clusterings of distinct species of tracers. Our estimators reduce to the one by Feldman, Kaiser & Peacock (ApJ 1994, FKP) in the case of a survey consisting of a single species of tracer. We show that the multi-tracer estimators are unbiased, and that their covariance is given by the inverse of the multi-tracer Fisher matrix (Abramo, MNRAS 2013; Abramo & Leonard, MNRAS 2013). When the biases, RSDs and NGs are fixed to their fiducial values, and one is only interested in measuring the underlying power spectrum, our estimators are projected into the estimator found by Percival, Verde & Peacock ...

  14. Energy spectra and passive tracer cascades in turbulent flows

    CERN Document Server

    Jolly, Michael

    2016-01-01

    We study the influence of the energy spectrum on the extent of the cascade range of a passive tracer in turbulent flows. The interesting cases are when there are two different spectra over the potential range of the tracer cascade (in 2D when the tracer forcing is in the inverse energy cascade range, and in 3D when the Schmidt number Sc is large). The extent of the tracer cascade range is then limited by the width of the range for the shallower of the two energy spectra. Nevertheless, we show that in dimension $d=2,3$ the tracer cascade range extends (up to a logarithm) to $\\kappa_{d\\text{D}}^{p}$, where $\\kappa_{d\\text{D}}$ is the wavenumber beyond which diffusion should dominate and $p$ is arbitrarily close to 1, provided Sc is larger than a certain power (depending on $p$) of the Grashof number. We also derive estimates which suggest that in 2D, for Sc${}\\sim1$ a wide tracer cascade can coexist with a significant inverse energy cascade at Grashof numbers large enough to produce a turbulent flow.

  15. A novel fluorescent retrograde neural tracer: cholera toxin B conjugated carbon dots

    Science.gov (United States)

    Zhou, Nan; Hao, Zeyu; Zhao, Xiaohuan; Maharjan, Suraj; Zhu, Shoujun; Song, Yubin; Yang, Bai; Lu, Laijin

    2015-09-01

    The retrograde neuroanatomical tracing method is a key technique to study the complex interconnections of the nervous system. Traditional tracers have several drawbacks, including time-consuming immunohistochemical or immunofluorescent staining procedures, rapid fluorescence quenching and low fluorescence intensity. Carbon dots (CDs) have been widely used as a fluorescent bio-probe due to their ultrasmall size, excellent optical properties, chemical stability, biocompatibility and low toxicity. Herein, we develop a novel fluorescent neural tracer: cholera toxin B-carbon dot conjugates (CTB-CDs). It can be taken up and retrogradely transported by neurons in the peripheral nervous system of rats. Our results show that CTB-CDs possess high photoluminescence intensity, good optical stability, a long shelf-life and non-toxicity. Tracing with CTB-CDs is a direct and more economical way of performing retrograde labelling experiments. Therefore, CTB-CDs are reliable fluorescent retrograde tracers.The retrograde neuroanatomical tracing method is a key technique to study the complex interconnections of the nervous system. Traditional tracers have several drawbacks, including time-consuming immunohistochemical or immunofluorescent staining procedures, rapid fluorescence quenching and low fluorescence intensity. Carbon dots (CDs) have been widely used as a fluorescent bio-probe due to their ultrasmall size, excellent optical properties, chemical stability, biocompatibility and low toxicity. Herein, we develop a novel fluorescent neural tracer: cholera toxin B-carbon dot conjugates (CTB-CDs). It can be taken up and retrogradely transported by neurons in the peripheral nervous system of rats. Our results show that CTB-CDs possess high photoluminescence intensity, good optical stability, a long shelf-life and non-toxicity. Tracing with CTB-CDs is a direct and more economical way of performing retrograde labelling experiments. Therefore, CTB-CDs are reliable fluorescent retrograde

  16. A Preliminary Study on the Measurement of Sediment Concentration in Hill-Slope Runoff with an Electrolyte Tracer

    Directory of Open Access Journals (Sweden)

    Xiaonan Shi Fan Zhang

    2012-01-01

    Full Text Available Sediment concentration in hill-slope runoff is an important index for soil erosion. Developing a reliable and portable measuring system of sediment concentration is a core issue for soil and water conservation study, especially for the Tibetan Plateau under unfavorable climate and terrain conditions for field investigation. Challenges include uneven distribution of sediment across a runoff section as well as difficulty in detecting a wide range of particle sizes. An electrolyte tracer, with the advantage of uniform distribution and its widely used electric-conductivity sensor, can avoid the problems of direct measurement of sediment. A new measurement method of sediment concentration in runoff with an electrolyte tracer is proposed based on a premise that sediment concentration is closely correlated with hydrodynamic dispersion coefficient of solute in runoff. In this study, an experiment system of hill-slope runoff with an electrolyte tracer and sediments is first designed. Second, two model parameters in the advective-dispersive equation of solute transport, flow velocity and diffusion coefficient, are inversely estimated by calibrating the observed concentrations of an electrolyte tracer. And third, the relationship between sediment concentrations and hydrodynamic dispersion coefficients are defined through specified regression. As a result, a measurement system of sediment concentration in hill-slope runoff with an electrolyte tracer is primarily established by integrating the relationship of variables, experiment system, and model theory.

  17. HYDROGEL TRACER BEADS: THE DEVELOPMENT, MODIFICATION, AND TESTING OF AN INNOVATIVE TRACER FOR BETTER UNDERSTANDING LNAPL TRANSPORT IN KARST AQUIFERS

    Energy Technology Data Exchange (ETDEWEB)

    Amanda Laskoskie, Harry M. Edenborn, and Dorothy J. Vesper

    2012-01-01

    The goal of this specific research task is to develop proxy tracers that mimic contaminant movement to better understand and predict contaminant fate and transport in karst aquifers. Hydrogel tracer beads are transported as a separate phase than water and can used as a proxy tracer to mimic the transport of non-aqueous phase liquids (NAPL). They can be constructed with different densities, sizes & chemical attributes. This poster describes the creation and optimization of the beads and the field testing of buoyant beads, including sampling, tracer analysis, and quantitative analysis. The buoyant beads are transported ahead of the dissolved solutes, suggesting that light NAPL (LNAPL) transport in karst may occur faster than predicted from traditional tracing techniques. The hydrogel beads were successful in illustrating this enhanced transport.

  18. An Advanced Reservoir Simulator for Tracer Transport in Multicomponent Multiphase Compositional Flow and Applications to the Cranfield CO2 Sequestration Site

    Science.gov (United States)

    Moortgat, J.

    2015-12-01

    Reservoir simulators are widely used to constrain uncertainty in the petrophysical properties of subsurface formations by matching the history of injection and production data. However, such measurements may be insufficient to uniquely characterize a reservoir's properties. Monitoring of natural (isotopic) and introduced tracers is a developing technology to further interrogate the subsurface for applications such as enhanced oil recovery from conventional and unconventional resources, and CO2 sequestration. Oak Ridge National Laboratory has been piloting this tracer technology during and following CO2 injection at the Cranfield, Mississippi, CO2 sequestration test site. Two campaigns of multiple perfluorocarbon tracers were injected together with CO2 and monitored at two wells at 68 m and 112 m from the injection site. The tracer data suggest that multiple CO2 flow paths developed towards the monitoring wells, indicative of either channeling through high permeability pathways or of fingering. The results demonstrate that tracers provide an important complement to transient pressure data. Numerical modeling is essential to further explain and interpret the observations. To aid the development of tracer technology, we enhanced a compositional multiphase reservoir simulator to account for tracer transport. Our research simulator uses higher-order finite element (FE) methods that can capture the small-scale onset of fingering on the coarse grids required for field-scale modeling, and allows for unstructured grids and anisotropic heterogeneous permeability fields. Mass transfer between fluid phases and phase behavior are modeled with rigorous equation-of-state based phase-split calculations. We present our tracer simulator and preliminary results related to the Cranfield experiments. Applications to noble gas tracers in unconventional resources are presented by Darrah et al.

  19. A Study Plan for Determining Recharge Rates at the Hanford Site Using Environmental Tracers

    Energy Technology Data Exchange (ETDEWEB)

    Murphy, E. M.; Szecsody, J. E.; Phillips, S. J.

    1991-02-01

    . Seven study sites on the Hanford Site have been selected, in two primary soil types that are believed to represent the extremes in recharge, the Quincy sand and the Warden silt loam. An additional background study site upwind of the Hanford facilities has been chosen at the Yakima Firing Center. Study sites at Hanford were chosen close to micrometeorology stations on downwind transects from the operational facilities. Initial testing will be done on sites that lack perennial vegetation. Six tracer techniques (total chlortde, {sup 36}Cl, {sup 3}H, nitrate, {sup 129}I, and {sup 99}Tc) will be tested on at least one site in the Quincy sand, one site in the Warden si~ loam, and the background site, to determine which combination of tracers wortks best for a given soil type. In subsequent years, additional sites will be investigated to determine the effect of vegetation on recharge estimates and on the performance of individual tracers. The use of environmental tracers is perhaps the only cost-effective method for estimating the spatial vartability of recharge at a site as large as Hanford. The tracer techniques used at Hanford have wide applicability at other and sites operated by the U.S. Department of Energy as well as at low-level radioactive waste disposal sites.

  20. Carbon monoxide toxicity. (Latest citations from the Life Sciences Collection database). NewSearch

    Energy Technology Data Exchange (ETDEWEB)

    1994-10-01

    The bibliography contains citations concerning the mechanism and clinical manifestations of carbon monoxide (CO) exposure, including the effects on the liver, cardiovascular, and nervous systems. Topics include studies of the carbon monoxide binding affinity with hemoglobin, measurement of carboxyhemoglobin in humans and various animal species, carbon monoxide levels resulting from tobacco and marijuana smoke, occupational exposure and the NIOSH (National Institute for Occupational Safety and Health) biological exposure index, symptomology and percent of blood CO, and intrauterine exposure. Air pollution, tobacco smoking, and occupational exposure are discussed as primary sources of carbon monoxide exposure. The effects of cigarette smoking on fetal development and health are excluded and examined in a separate bibliography. (Contains a minimum of 137 citations and includes a subject term index and title list.)