WorldWideScience

Sample records for monolith fbsr mineral

  1. FLUIDIZED BED STEAM REFORMER (FBSR) PRODUCT: MONOLITH FORMATION AND CHARACTERIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2006-09-13

    The most important requirement for Hanford's low activity waste (LAW) form for shallow land disposal is the chemical durability of the product. A secondary, but still essential specification, is the compressive strength of the material with regards to the strength of the material under shallow land disposal conditions, e.g. the weight of soil overburden and potential intrusion by future generations, because the term ''near-surface disposal'' indicates disposal in the uppermost portion, or approximately the top 30 meters, of the earth's surface. The THOR{reg_sign} Treatment Technologies (TTT) mineral waste form for LAW is granular in nature because it is formed by Fluidized Bed Steam Reforming (FBSR). As a granular product it has been shown to be as durable as Hanford's LAW glass during testing with ASTM C-1285-02 known as the Product Consistency Test (PCT) and with the Single Pass Flow Through Test (SPFT). Hanford Envelope A and Envelope C simulants both performed well during PCT and SPFT testing and during subsequent performance assessment modeling. This is partially due to the high aluminosilicate content of the mineral product which provides a natural aluminosilicate buffering mechanism that inhibits leaching and is known to occur in naturally occurring aluminosilicate mineral analogs. In order for the TTT Na-Al-Si (NAS) granular mineral product to meet the compressive strength requirements (ASTM C39) for a Hanford waste form, the granular product needs to be made into a monolith or disposed of in High Integrity Containers (HIC's). Additionally, the Hanford intruder scenario for disposal in the Immobilized Low Activity Waste (ILAW) trench is mitigated as there is reduced intruder exposure when a waste form is in a monolithic form. During the preliminary testing of a monolith binder for TTT's FBSR mineral product, four parameters were monitored: (1) waste loading (not optimized for each waste form tested); (2) density

  2. Radioactive Demonstration Of Mineralized Waste Forms Made From Hanford Low Activity Waste (Tank Farm Blend) By Fluidized Bed Steam Reformation (FBSR)

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Bannochie, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, W. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hall, H. K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Miller, D. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, D. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Williams, M. F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2013-08-01

    The U.S. Department of Energy’s Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford’s tank waste. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Hanford Tank Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Supplemental Treatment is likely to be required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. The Supplemental Treatment chosen will immobilize that portion of the retrieved LAW that is not sent to the WTP’s LAW Vitrification facility into a solidified waste form. The solidified waste will then be disposed on the Hanford site in the Integrated Disposal Facility (IDF). Fluidized Bed Steam Reforming (FBSR) offers a moderate temperature (700-750°C) continuous method by which LAW can be processed irrespective of whether the waste contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology can process these wastes into a crystalline ceramic (mineral) waste form. The mineral waste form that is produced by co-processing waste with kaolin clay in an FBSR process has been shown to be comparable to LAW glass, i.e. leaches Tc-99, Re and Na at <2g/m2 during ASTM C1285 (Product Consistency) durability testing. Monolithing of the granular FBSR product was investigated to prevent dispersion during transport or burial/storage. Monolithing in an inorganic geopolymer binder, which is

  3. Radioactive Demonstration Of Mineralized Waste Forms Made From Hanford Low Activity Waste (Tank SX-105, Tank AN-103, And AZ-101/102) By Fluidized Bed Steam Reformation (FBSR)

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M.; Crawford, C. L.; Bannochie, C. J.; Burket, P. R.; Cozzi, A. D.; Daniel, W. E.; Hall, H. K.; Miller, D. H.; Missimer, D. M.; Nash, C. A.; Williams, M. F.

    2013-09-18

    Fluidized Bed Steam Reforming (FBSR) is a robust technology for the immobilization of a wide variety of radioactive wastes. Applications have been tested at the pilot scale for the high sodium, sulfate, halide, organic and nitrate wastes at the Hanford site, the Idaho National Laboratory (INL), and the Savannah River Site (SRS). Due to the moderate processing temperatures, halides, sulfates, and technetium are retained in mineral phases of the feldspathoid family (nepheline, sodalite, nosean, carnegieite, etc). The feldspathoid minerals bind the contaminants such as Tc-99 in cage (sodalite, nosean) or ring (nepheline) structures to surrounding aluminosilicate tetrahedra in the feldspathoid structures. The granular FBSR mineral waste form that is produced has a comparable durability to LAW glass based on the short term PCT testing in this study, the INL studies, SPFT and PUF testing from previous studies as given in the columns in Table 1-3 that represent the various durability tests. Monolithing of the granular product was shown to be feasible in a separate study. Macro-encapsulating the granular product provides a decrease in leaching compared to the FBSR granular product when the geopolymer is correctly formulated.

  4. Radioactive Demonstration Of Mineralized Waste Forms Made From Hanford Low Activity Waste (Tank Farm Blend) By Fluidized Bed Steam Reformation (FBSR)

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Bannochie, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, W. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hall, H. K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Miller, D. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, D. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Williams, M. F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2013-08-01

    The U.S. Department of Energy’s Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford’s tank waste. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Hanford Tank Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Supplemental Treatment is likely to be required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. The Supplemental Treatment chosen will immobilize that portion of the retrieved LAW that is not sent to the WTP’s LAW Vitrification facility into a solidified waste form. The solidified waste will then be disposed on the Hanford site in the Integrated Disposal Facility (IDF). Fluidized Bed Steam Reforming (FBSR) offers a moderate temperature (700-750°C) continuous method by which LAW can be processed irrespective of whether the waste contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology can process these wastes into a crystalline ceramic (mineral) waste form. The mineral waste form that is produced by co-processing waste with kaolin clay in an FBSR process has been shown to be comparable to LAW glass, i.e. leaches Tc-99, Re and Na at <2g/m2 during ASTM C1285 (Product Consistency) durability testing. Monolithing of the granular FBSR product was investigated to prevent dispersion during transport or burial/storage. Monolithing in an inorganic geopolymer binder, which is

  5. MINERALIZATION OF RADIOACTIVE WASTES BY FLUIDIZED BED STEAM REFORMING (FBSR): COMPARISONS TO VITREOUS WASTE FORMS, AND PERTINENT DURABILITY TESTING

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2008-12-26

    The Savannah River National Laboratory (SRNL) was requested to generate a document for the Washington State Department of Ecology and the U.S. Environmental Protection Agency that would cover the following topics: (1) A description of the mineral structures produced by Fluidized Bed Steam Reforming (FBSR) of Hanford type Low Activity Waste (LAW including LAWR which is LAW melter recycle waste) waste, especially the cage structured minerals and how they are formed. (2) How the cage structured minerals contain some contaminants, while others become part of the mineral structure (Note that all contaminants become part of the mineral structure and this will be described in the subsequent sections of this report). (3) Possible contaminant release mechanisms from the mineral structures. (4) Appropriate analyses to evaluate these release mechanisms. (5) Why the appropriate analyses are comparable to the existing Hanford glass dataset. In order to discuss the mineral structures and how they bond contaminants a brief description of the structures of both mineral (ceramic) and vitreous waste forms will be given to show their similarities. By demonstrating the similarities of mineral and vitreous waste forms on atomic level, the contaminant release mechanisms of the crystalline (mineral) and amorphous (glass) waste forms can be compared. This will then logically lead to the discussion of why many of the analyses used to evaluate vitreous waste forms and glass-ceramics (also known as glass composite materials) are appropriate for determining the release mechanisms of LAW/LAWR mineral waste forms and how the durability data on LAW/LAWR mineral waste forms relate to the durability data for LAW/LAWR glasses. The text will discuss the LAW mineral waste form made by FBSR. The nanoscale mechanism by which the minerals form will be also be described in the text. The appropriate analyses to evaluate contaminant release mechanisms will be discussed, as will the FBSR test results to

  6. Radioactive Demonstrations Of Fluidized Bed Steam Reforming (FBSR) With Hanford Low Activity Wastes

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M.; Crawford, C. L.; Burket, P. R.; Bannochie, C. J.; Daniel, W. G.; Nash, C. A.; Cozzi, A. D.; Herman, C. C.

    2012-10-22

    Several supplemental technologies for treating and immobilizing Hanford low activity waste (LAW) are being evaluated. One immobilization technology being considered is Fluidized Bed Steam Reforming (FBSR) which offers a low temperature (700-750?C) continuous method by which wastes high in organics, nitrates, sulfates/sulfides, or other aqueous components may be processed into a crystalline ceramic (mineral) waste form. The granular waste form produced by co-processing the waste with kaolin clay has been shown to be as durable as LAW glass. The FBSR granular product will be monolithed into a final waste form. The granular component is composed of insoluble sodium aluminosilicate (NAS) feldspathoid minerals such as sodalite. Production of the FBSR mineral product has been demonstrated both at the industrial, engineering, pilot, and laboratory scales on simulants. Radioactive testing at SRNL commenced in late 2010 to demonstrate the technology on radioactive LAW streams which is the focus of this study.

  7. FLUIDIZED BED STEAM REFORMER MONOLITH FORMATION

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2006-12-22

    Fluidized Bed Steam Reforming (FBSR) is being considered as an alternative technology for the immobilization of a wide variety of aqueous high sodium containing radioactive wastes at various DOE facilities in the United States. The addition of clay, charcoal, and a catalyst as co-reactants converts aqueous Low Activity Wastes (LAW) to a granular or ''mineralized'' waste form while converting organic components to CO{sub 2} and steam, and nitrate/nitrite components, if any, to N{sub 2}. The waste form produced is a multiphase mineral assemblage of Na-Al-Si (NAS) feldspathoid minerals with cage-like structures that atomically bond radionuclides like Tc-99 and anions such as SO{sub 4}, I, F, and Cl. The granular product has been shown to be as durable as LAW glass. Shallow land burial requires that the mineralized waste form be able to sustain the weight of soil overburden and potential intrusion by future generations. The strength requirement necessitates binding the granular product into a monolith. FBSR mineral products were formulated into a variety of monoliths including various cements, Ceramicrete, and hydroceramics. All but one of the nine monoliths tested met the <2g/m{sup 2} durability specification for Na and Re (simulant for Tc-99) when tested using the Product Consistency Test (PCT; ASTM C1285). Of the nine monoliths tested the cements produced with 80-87 wt% FBSR product, the Ceramicrete, and the hydroceramic produced with 83.3 wt% FBSR product, met the compressive strength and durability requirements for an LAW waste form.

  8. Mineral assemblage transformation of a metakaolin-based waste form after geopolymer encapsulation

    Science.gov (United States)

    Williams, Benjamin D.; Neeway, James J.; Snyder, Michelle M. V.; Bowden, Mark E.; Amonette, James E.; Arey, Bruce W.; Pierce, Eric M.; Brown, Christopher F.; Qafoku, Nikolla P.

    2016-05-01

    Mitigation of hazardous and radioactive waste can be improved through conversion of existing waste to a more chemically stable and physically robust waste form. One option for waste conversion is the fluidized bed steam reforming (FBSR) process. The resulting FBSR granular material was encapsulated in a geopolymer matrix referred to here as Geo-7. This provides mechanical strength for ease in transport and disposal. However, it is necessary to understand the phase assemblage evolution as a result of geopolymer encapsulation. In this study, we examine the mineral assemblages formed during the synthesis of the multiphase ceramic waste form. The FBSR granular samples were created from waste simulant that was chemically adjusted to resemble Hanford tank waste. Another set of samples was created using Savannah River Site Tank 50 waste simulant in order to mimic a blend of waste collected from 68 Hanford tank. Waste form performance tests were conducted using the product consistency test (PCT), the Toxicity Characteristic Leaching Procedure (TCLP), and the single-pass flow-through (SPFT) test. X-ray diffraction analyses revealed the structure of a previously unreported NAS phase and indicate that monolith creation may lead to a reduction in crystallinity as compared to the primary FBSR granular product.

  9. Radioactive demonstration of final mineralized waste forms for Hanford waste treatment plant secondary waste (WTP-SW) by fluidized bed steam reforming (FBSR) using the bench scale reformer platform

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Jantzen, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2014-08-01

    The U.S. Department of Energy’s Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford’s tank waste. Currently there are approximately 56 million gallons of highly radioactive mixed wastes awaiting treatment. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Therefore, Supplemental Treatment is required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. In addition, the WTP LAW vitrification facility off-gas condensate known as WTP Secondary Waste (WTP-SW) will be generated and enriched in volatile components such as 137Cs, 129I, 99Tc, Cl, F, and SO4 that volatilize at the vitrification temperature of 1150°C in the absence of a continuous cold cap (that could minimize volatilization). The current waste disposal path for the WTP-SW is to process it through the Effluent Treatment Facility (ETF). Fluidized Bed Steam Reforming (FBSR) is being considered for immobilization of the ETF concentrate that would be generated by processing the WTP-SW. The focus of this current report is the WTP-SW.

  10. RADIOACTIVE DEMONSTRATIONS OF FLUIDIZED BED STEAM REFORMING WITH ACUTAL HANFORD LOW ACTIVITY WASTES VERIFYING FBSR AS A SUPPLEMENTARY TREATMENT

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C.; Crawford, C.; Burket, P.; Bannochie, C.; Daniel, G.; Nash, C.; Cozzi, A.; Herman, C.

    2012-01-12

    The U.S. Department of Energy's Office of River Protection is responsible for the retrieval, treatment, immobilization, and disposal of Hanford's tank waste. Currently there are approximately 56 million gallons of highly radioactive mixed wastes awaiting treatment. A key aspect of the River Protection Project cleanup mission is to construct and operate the Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level waste (HLW) and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the cleanup mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA). Therefore, Supplemental Treatment is required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. Fluidized Bed Steam Reforming (FBSR) is one of the supplementary treatments being considered. FBSR offers a moderate temperature (700-750 C) continuous method by which LAW and other secondary wastes can be processed irrespective of whether they contain organics, nitrates/nitrites, sulfates/sulfides, chlorides, fluorides, and/or radio-nuclides like I-129 and Tc-99. Radioactive testing of Savannah River LAW (Tank 50) shimmed to resemble Hanford LAW and actual Hanford LAW (SX-105 and AN-103) have produced a ceramic (mineral) waste form which is the same as the non-radioactive waste simulants tested at the engineering scale. The radioactive testing demonstrated that the FBSR process can retain the volatile radioactive components that cannot be contained at vitrification temperatures. The radioactive and nonradioactive mineral waste forms that were produced by co-processing waste with kaolin clay in an FBSR process are shown to be as durable as LAW glass.

  11. Mineral assemblage transformation of a metakaolin-based waste form after geopolymer encapsulation

    Energy Technology Data Exchange (ETDEWEB)

    Williams, Benjamin D.; Neeway, James J.; Snyder, Michelle M. V.; Bowden, Mark E.; Amonette, James E.; Arey, Bruce W.; Pierce, Eric M.; Brown, Christopher F.; Qafoku, Nikolla P.

    2016-05-01

    Current plans for nuclear waste vitrification at the Hanford Tank Waste Treatment and Immobilization Plant (WTP) lack the capacity to treat all of the low activity waste (LAW) that is not encapsulated in the vitrified product. Fluidized Bed Steam Reforming (FBSR) is one of the supplemental technologies under consideration to fill this gap. The FBSR process results in a granular product mainly composed of feldspathoid mineral phases that encapsulate the LAW and other contaminants of concern (COCs). In order to better understand the characteristics of the FBSR product, characterization testing has been performed on the granular product as well as the granular product encapsulated in a monolithic geopolymer binder. The non-radioactive simulated tank waste samples created for use in this study are the result of a 2008 Department of Energy sponsored Engineering Scale Technology Demonstration (ESTD) in 2008. These samples were created from waste simulant that was chemically shimmed to resemble actual tank waste, and rhenium has been used as a substitute for technetium. Another set of samples was created by the Savannah River Site Bench-Scale Reformer (BSR) using a chemical shim of Savannah River Site Tank 50 waste in order to simulate a blend of 68 Hanford tank wastes. This paper presents results from coal and moisture removal tests along with XRD, SEM, and BET analyses showing that the major mineral components are predominantly sodium aluminosilicate minerals and that the mineral product is highly porous. Results also show that the materials pass the short-term leach tests: the Toxicity Characteristic Leaching Procedure (TCLP) and Product Consistency Test (PCT).

  12. RADIOACTIVE DEMONSTRATION OF FINAL MINERALIZED WASTE FORMS FOR HANFORD WASTE TREATMENT PLANT SECONDARY WASTE BY FLUIDIZED BED STEAM REFORMING USING THE BENCH SCALE REFORMER PLATFORM

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C.; Burket, P.; Cozzi, A.; Daniel, W.; Jantzen, C.; Missimer, D.

    2012-02-02

    ceramic (mineral) waste form. The mineral waste form that is produced by co-processing waste with kaolin clay in an FBSR process has been shown to be as durable as LAW glass. Monolithing of the granular FBSR product is being investigated to prevent dispersion during transport or burial/storage, but is not necessary for performance. A Benchscale Steam Reformer (BSR) was designed and constructed at the SRNL to treat actual radioactive wastes to confirm the findings of the non-radioactive FBSR pilot scale tests and to qualify the waste form for applications at Hanford. BSR testing with WTP SW waste surrogates and associated analytical analyses and tests of granular products (GP) and monoliths began in the Fall of 2009, and then was continued from the Fall of 2010 through the Spring of 2011. Radioactive testing commenced in 2010 with a demonstration of Hanford's WTP-SW where Savannah River Site (SRS) High Level Waste (HLW) secondary waste from the Defense Waste Processing Facility (DWPF) was shimmed with a mixture of {sup 125/129}I and {sup 99}Tc to chemically resemble WTP-SW. Prior to these radioactive feed tests, non-radioactive simulants were also processed. Ninety six grams of radioactive granular product were made for testing and comparison to the non-radioactive pilot scale tests. The same mineral phases were found in the radioactive and non-radioactive testing.

  13. FLUIDIZED BED STEAM REFORMING (FBSR) OF HIGH LEVEL WASTE (HLW) ORGANIC AND NITRATE DESTRUCTION PRIOR TO VITRIFICATION: CRUCIBLE SCALE TO ENGINEERING SCALE DEMONSTRATIONS AND NON-RADIOACTIVE TO RADIOACTIVE DEMONSTRATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C; Michael Williams, M; Gene Daniel, G; Paul Burket, P; Charles Crawford, C

    2009-02-07

    Over a decade ago, an in-tank precipitation process to remove Cs-137 from radioactive high level waste (HLW) supernates was demonstrated at the Savannah River Site (SRS). The full scale demonstration with actual HLW was performed in SRS Tank 48 (T48). Sodium tetraphenylborate (NaTPB) was added to enable Cs-137 extraction as CsTPB. The CsTPB, an organic, and its decomposition products proved to be problematic for subsequent processing of the Cs-137 precipitate in the SRS HLW vitrification facility for ultimate disposal in a HLW repository. Fluidized Bed Steam Reforming (FBSR) is being considered as a technology for destroying the organics and nitrates in the T48 waste to render it compatible with subsequent HLW vitrification. During FBSR processing the T48 waste is converted into organic-free and nitrate-free carbonate-based minerals which are water soluble. The soluble nature of the carbonate-based minerals allows them to be dissolved and pumped to the vitrification facility or returned to the tank farm for future vitrification. The initial use of the FBSR process for T48 waste was demonstrated with simulated waste in 2003 at the Savannah River National Laboratory (SRNL) using a specially designed sealed crucible test that reproduces the FBSR pyrolysis reactions, i.e. carbonate formation, organic and nitrate destruction. This was followed by pilot scale testing of simulants at the Science Applications International Corporation (SAIC) Science & Technology Application Research (STAR) Center in Idaho Falls, ID by Idaho National Laboratory (INL) and SRNL in 2003-4 and then engineering scale demonstrations by THOR{reg_sign} Treatment Technologies (TTT) and SRS/SRNL at the Hazen Research, Inc. (HRI) test facility in Golden, CO in 2006 and 2008. Radioactive sealed crucible testing with real T48 waste was performed at SRNL in 2008, and radioactive Benchscale Steam Reformer (BSR) testing was performed in the SRNL Shielded Cell Facility (SCF) in 2008.

  14. Fluidized bed steam reformed mineral waste form performance testing to support Hanford Supplemental Low Activity Waste Immobilization Technology Selection

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Pierce, E. M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bannochie, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, W. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fox, K. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Herman, C. C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Miller, D. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, D. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Williams, M. F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Brown, C. F. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Qafoku, N. P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Neeway, J. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Valenta, M. M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gill, G. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Swanberg, D. J. [Washington River Protection Solutions (WRPS), Richland, WA (United States); Robbins, R. A. [Washington River Protection Solutions (WRPS), Richland, WA (United States); Thompson, L. E. [Washington River Protection Solutions (WRPS), Richland, WA (United States)

    2015-10-01

    This report describes the benchscale testing with simulant and radioactive Hanford Tank Blends, mineral product characterization and testing, and monolith testing and characterization. These projects were funded by DOE EM-31 Technology Development & Deployment (TDD) Program Technical Task Plan WP-5.2.1-2010-001 and are entitled “Fluidized Bed Steam Reformer Low-Level Waste Form Qualification”, Inter-Entity Work Order (IEWO) M0SRV00054 with Washington River Protection Solutions (WRPS) entitled “Fluidized Bed Steam Reforming Treatability Studies Using Savannah River Site (SRS) Low Activity Waste and Hanford Low Activity Waste Tank Samples”, and IEWO M0SRV00080, “Fluidized Bed Steam Reforming Waste Form Qualification Testing Using SRS Low Activity Waste and Hanford Low Activity Waste Tank Samples”. This was a multi-organizational program that included Savannah River National Laboratory (SRNL), THOR® Treatment Technologies (TTT), Pacific Northwest National Laboratory (PNNL), Oak Ridge National Laboratory (ORNL), Office of River Protection (ORP), and Washington River Protection Solutions (WRPS). The SRNL testing of the non-radioactive pilot-scale Fluidized Bed Steam Reformer (FBSR) products made by TTT, subsequent SRNL monolith formulation and testing and studies of these products, and SRNL Waste Treatment Plant Secondary Waste (WTP-SW) radioactive campaign were funded by DOE Advanced Remediation Technologies (ART) Phase 2 Project in connection with a Work-For-Others (WFO) between SRNL and TTT.

  15. Monolithic spectrometer

    Science.gov (United States)

    Rajic, Slobodan; Egert, Charles M.; Kahl, William K.; Snyder, Jr., William B.; Evans, III, Boyd M.; Marlar, Troy A.; Cunningham, Joseph P.

    1998-01-01

    A monolithic spectrometer is disclosed for use in spectroscopy. The spectrometer is a single body of translucent material with positioned surfaces for the transmission, reflection and spectral analysis of light rays.

  16. Radioactive Demonstration Of Mineralized Waste Forms Made From Hanford Low Activity Waste (Tank SX-105 And AN-103) By Fluidized Bed Steam Reformation

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, Carol; Herman, Connie; Crawford, Charles; Bannochie, Christopher; Burket, Paul; Daniel, Gene; Cozzi, Alex; Nash, Charles; Miller, Donald; Missimer, David

    2014-01-10

    One of the immobilization technologies under consideration as a Supplemental Treatment for Hanford’s Low Activity Waste (LAW) is Fluidized Bed Steam Reforming (FBSR). The FBSR technology forms a mineral waste form at moderate processing temperatures thus retaining and atomically bonding the halides, sulfates, and technetium in the mineral phases (nepheline, sodalite, nosean, carnegieite). Additions of kaolin clay are used instead of glass formers and the minerals formed by the FBSR technology offers (1) atomic bonding of the radionuclides and constituents of concern (COC) comparable to glass, (2) short and long term durability comparable to glass, (3) disposal volumes comparable to glass, and (4) higher Na2O and SO{sub 4} waste loadings than glass. The higher FBSR Na{sub 2}O and SO{sub 4} waste loadings contribute to the low disposal volumes but also provide for more rapid processing of the LAW. Recent FBSR processing and testing of Hanford radioactive LAW (Tank SX-105 and AN-103) waste is reported and compared to previous radioactive and non-radioactive LAW processing and testing.

  17. EVALUATION OF THOR MINERALIZED WASTE FORMS FOR THE DOE ADVANCED REMEDIATION TECHNOLOGIES PHASE 2 PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C.; Jantzen, C.

    2012-02-02

    , sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology can process these wastes into a crystalline ceramic (mineral) waste form. The mineral waste form that is produced by co-processing waste with kaolin clay in an FBSR process has been shown to be as durable as LAW glass. Monolithing of the granular FBSR product, which is one of the objectives of this current study, is being investigated to prevent dispersion during transport or burial/storage but is not necessary for performance. FBSR testing of a Hanford LAW simulant and a WTP-SW simulant at the pilot scale was performed by THOR Treatment Technologies, LLC at Hazen Research Inc. in April/May 2008. The Hanford LAW simulant was the Rassat 68 tank blend and the target concentrations for the LAW was increased by a factor of 10 for Sb, As, Ag, Cd, and Tl; 100 for Ba and Re (Tc surrogate); 1,000 for I; and 254,902 for Cs based on discussions with the DOE field office and the environmental regulators and an evaluation of the Hanford Tank Waste Envelopes A, B, and C. It was determined through the evaluation of the actual tank waste metals concentrations that some metal levels were not sufficient to achieve reliable detection in the off-gas sampling. Therefore, the identified metals concentrations were increased in the Rassat simulant processed by TTT at HRI to ensure detection and enable calculation of system removal efficiencies, product retention efficiencies, and mass balance closure without regard to potential results of those determinations or impacts on product durability response such as Toxicity Characteristic Leach Procedure (TCLP). A WTP-SW simulant based on melter off-gas analyses from Vitreous State Laboratory (VSL) was also tested at HRI in the 15-inch diameter Engineering Scale Test Demonstration (ESTD) dual reformer at HRI in 2008. The target concentrations for the Resource Conservation and Recovery Act (RCRA) metals were increased by 16X for Se, 29X for

  18. CRUCIBLE TESTING OF TANK 48 RADIOACTIVE WASTE SAMPLE USING FBSR TECHNOLOGY FOR ORGANIC DESTRUCTION

    Energy Technology Data Exchange (ETDEWEB)

    Hammond, C; William Pepper, W

    2008-09-19

    The purpose of crucible scale testing with actual radioactive Tank 48H material was to duplicate the test results that had been previously performed on simulant Tank 48H material. The earlier crucible scale testing using simulants was successful in demonstrating that bench scale crucible tests produce results that are indicative of actual Fluidized Bed Steam Reforming (FBSR) pilot scale tests. Thus, comparison of the results using radioactive Tank 48H feed to those reported earlier with simulants would then provide proof that the radioactive tank waste behaves in a similar manner to the simulant. Demonstration of similar behavior for the actual radioactive Tank 48H slurry to the simulant is important as a preliminary or preparation step for the more complex bench-scale steam reformer unit that is planned for radioactive application in the Savannah River National Laboratory (SRNL) Shielded Cells Facility (SCF) later in 2008. The goals of this crucible-scale testing were to show 99% destruction of tetraphenylborate and to demonstrate that the final solid product produced is sodium carbonate. Testing protocol was repeated using the specifications of earlier simulant crucible scale testing, that is sealed high purity alumina crucibles containing a pre-carbonated and evaporated Tank 48H material. Sealing of the crucibles was accomplished by using an inorganic 'nepheline' sealant. The sealed crucibles were heat-treated at 650 C under constant argon flow to inert the system. Final product REDOX measurements were performed to establish the REDuction/OXidation (REDOX) state of known amounts of added iron species in the final product. These REDOX measurements confirm the processing conditions (pyrolysis occurring at low oxygen fugacity) of the sealed crucible environment which is the environment actually achieved in the fluidized bed steam reformer process. Solid product dissolution in water was used to measure soluble cations and anions, and to investigate

  19. EVALUATION OF THOR MINERALIZED WASTE FORMS FOR THE DOE ADVANCED REMEDIATION TECHNOLOGIES PHASE 2 PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C.; Jantzen, C.

    2012-02-02

    , sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology can process these wastes into a crystalline ceramic (mineral) waste form. The mineral waste form that is produced by co-processing waste with kaolin clay in an FBSR process has been shown to be as durable as LAW glass. Monolithing of the granular FBSR product, which is one of the objectives of this current study, is being investigated to prevent dispersion during transport or burial/storage but is not necessary for performance. FBSR testing of a Hanford LAW simulant and a WTP-SW simulant at the pilot scale was performed by THOR Treatment Technologies, LLC at Hazen Research Inc. in April/May 2008. The Hanford LAW simulant was the Rassat 68 tank blend and the target concentrations for the LAW was increased by a factor of 10 for Sb, As, Ag, Cd, and Tl; 100 for Ba and Re (Tc surrogate); 1,000 for I; and 254,902 for Cs based on discussions with the DOE field office and the environmental regulators and an evaluation of the Hanford Tank Waste Envelopes A, B, and C. It was determined through the evaluation of the actual tank waste metals concentrations that some metal levels were not sufficient to achieve reliable detection in the off-gas sampling. Therefore, the identified metals concentrations were increased in the Rassat simulant processed by TTT at HRI to ensure detection and enable calculation of system removal efficiencies, product retention efficiencies, and mass balance closure without regard to potential results of those determinations or impacts on product durability response such as Toxicity Characteristic Leach Procedure (TCLP). A WTP-SW simulant based on melter off-gas analyses from Vitreous State Laboratory (VSL) was also tested at HRI in the 15-inch diameter Engineering Scale Test Demonstration (ESTD) dual reformer at HRI in 2008. The target concentrations for the Resource Conservation and Recovery Act (RCRA) metals were increased by 16X for Se, 29X for

  20. Monoliths in Bioprocess Technology

    Directory of Open Access Journals (Sweden)

    Vignesh Rajamanickam

    2015-04-01

    Full Text Available Monolithic columns are a special type of chromatography column, which can be used for the purification of different biomolecules. They have become popular due to their high mass transfer properties and short purification times. Several articles have already discussed monolith manufacturing, as well as monolith characteristics. In contrast, this review focuses on the applied aspect of monoliths and discusses the most relevant biomolecules that can be successfully purified by them. We describe success stories for viruses, nucleic acids and proteins and compare them to conventional purification methods. Furthermore, the advantages of monolithic columns over particle-based resins, as well as the limitations of monoliths are discussed. With a compilation of commercially available monolithic columns, this review aims at serving as a ‘yellow pages’ for bioprocess engineers who face the challenge of purifying a certain biomolecule using monoliths.

  1. Minerals

    Directory of Open Access Journals (Sweden)

    Vaquero, M. P.

    1998-08-01

    Full Text Available The possible changes in the mineral composition of food during frying could be the consequence of losses by leaching, or changes in concentrations caused by exchanges between the food and culinary fat of other compounds. The net result depends on the type of food, the frying fat used and the frying process. Moreover, the modifications that frying produces in other nutrients could indirectly affect the availability of dietary minerals. The most outstanding ones are those that can take place in the fat or in the protein. With respect to the interactions between frying oils and minerals, we have recent knowledge concerning the effects of consuming vegetable oils used in repeated fryings of potatoes without turnover, on the nutritive utilization of dietary minerals. The experiments have been carried out in pregnant and growing rats, which consumed diets containing, as a sole source of fat, the testing frying oils or unused oils. It seems that the consumption of various frying oils, with a polar compound content lower or close to the maximum limit of 25% accepted for human consumption, does not alter the absorption and metabolism of calcium, phosphorous, iron or copper. Magnesium absorption from diets containing frying oils tends to increase but the urinary excretion of this element increases, resulting imperceptible the variations in the magnesium balance. The urinary excretion of Zn also increased although its balance remained unchanged. Different studies referring to the effects of consuming fried fatty fish on mineral bioavailability will also be presented. On one hand, frying can cause structural changes in fish protein, which are associated with an increase in iron absorption and a decrease in body zinc retention. The nutritive utilization of other elements such as magnesium, calcium and copper seems to be unaffected. On the other hand; it has been described that an excess of fish fatty acids in the diet produces iron depletion, but when fatty

  2. Report for Treating Hanford LAW and WTP SW Simulants: Pilot Plant Mineralizing Flowsheet

    Energy Technology Data Exchange (ETDEWEB)

    Arlin Olson

    2012-02-28

    The US Department of Energy is responsible for managing the disposal of radioactive liquid waste in underground storage tanks at the Hanford site in Washington State. The Hanford waste treatment and immobilization plant (WPT) will separate the waste into a small volume of high level waste (HLW), containing most of the radioactive constituents, and a larger volume of low activity waste (LAW), containing most of the non-radioactive chemical and hazardous constituents. The HLW and LAW will be converted into immobilized waste forms for disposal. Currently there is inadequate LAW vitrification capacity planned at the WTP to complete the mission within the required timeframe. Therefore additional LAW capacity is required. One candidate supplemental treatment technology is the fluidized bed steam reformer process (FBSR). This report describes the demonstration testing of the FBSR process using a mineralizing flowsheet for treating simulated Hanford LAW and secondary waste from the WTP (WTP SW). The FBSR testing project produced leach-resistant solid products and environmentally compliant gaseous effluents. The solid products incorporated normally soluble ions into an alkali alumino-silicate (NaS) mineral matrix. Gaseous emissions were found to be within regulatory limits. Cesium and rhenium were captured in the mineralized products with system removal efficiencies of 99.999% and 99.998 respectively. The durability and leach performance of the FBSR granular solid were superior to the low activity reference material (LMR) glass standards. Normalized product consistency test (PCT) release rates for constituents of concern were approximately 2 orders of magnitude less than that of sodium in the Hanford glass [standard].

  3. Monolithic microwave integrated circuits

    Science.gov (United States)

    Pucel, R. A.

    Monolithic microwave integrated circuits (MMICs), a new microwave technology which is expected to exert a profound influence on microwave circuit designs for future military systems as well as for the commercial and consumer markets, is discussed. The book contains an historical discussion followed by a comprehensive review presenting the current status in the field. The general topics of the volume are: design considerations, materials and processing considerations, monolithic circuit applications, and CAD, measurement, and packaging techniques. All phases of MMIC technology are covered, from design to testing.

  4. Embedded-monolith armor

    Science.gov (United States)

    McElfresh, Michael W.; Groves, Scott E; Moffet, Mitchell L.; Martin, Louis P.

    2016-07-19

    A lightweight armor system utilizing a face section having a multiplicity of monoliths embedded in a matrix supported on low density foam. The face section is supported with a strong stiff backing plate. The backing plate is mounted on a spall plate.

  5. Monolithic MACS micro resonators

    Science.gov (United States)

    Lehmann-Horn, J. A.; Jacquinot, J.-F.; Ginefri, J. C.; Bonhomme, C.; Sakellariou, D.

    2016-10-01

    Magic Angle Coil Spinning (MACS) aids improving the intrinsically low NMR sensitivity of heterogeneous microscopic samples. We report on the design and testing of a new type of monolithic 2D MACS resonators to overcome known limitations of conventional micro coils. The resonators' conductors were printed on dielectric substrate and tuned without utilizing lumped element capacitors. Self-resonance conditions have been computed by a hybrid FEM-MoM technique. Preliminary results reported here indicate robust mechanical stability, reduced eddy currents heating and negligible susceptibility effects. The gain in B1 /√{ P } is in agreement with the NMR sensitivity enhancement according to the principle of reciprocity. A sensitivity enhancement larger than 3 has been achieved in a monolithic micro resonator inside a standard 4 mm rotor at 500 MHz. These 2D resonators could offer higher performance micro-detection and ease of use of heterogeneous microscopic substances such as biomedical samples, microscopic specimens and thin film materials.

  6. The MONOLITH prototype

    CERN Document Server

    Ambrosio, M; Bencivenni, G; Candela, A M; Chiarini, A; Chignoli, F; De Deo, M; D'Incecco, M; Gerli, S; Giusti, P; Gómez, F; Gustavino, C; Lindozzi, M; Mannocchi, G; Menghetti, H; Morello, C; Murtas, F; Paoluzzi, G; Pilastrini, R; Redaelli, N G; Santoni, M; Sartorelli, G; Terranova, F; Trinchero, G C

    2000-01-01

    MONOLITH (Massive Observatory for Neutrino Oscillation or LImits on THeir existence) is the project of an experiment to study atmospheric neutrino oscillations with a massive magnetized iron detector. The baseline option is a 34 kt iron detector based on the use of about 50000 m/sup 2/ of the glass Resistive Plate Chambers (glass RPCs) developed at the Laboratori Nazionali del Gran Sasso (LNGS). An 8 ton prototype equipped with 23 m/sup 2/ of glass RPC has been realized and tested at the T7-PS beam at CERN. The energy resolution for pions follows a 68%/ square root (E(GeV))+2% law for orthogonally incident particles, in the energy range between 2 and 10 GeV. The time resolution and the tracking capability of the glass RPC are suitable for the MONOLITH experiment. (7 refs).

  7. Bioaffinity chromatography on monolithic supports

    NARCIS (Netherlands)

    Tetala, K.K.R.; Beek, van T.A.

    2010-01-01

    Affinity chromatography on monolithic supports is a powerful analytical chemical platform because it allows for fast analyses, small sample volumes, strong enrichment of trace biomarkers and applications in microchips. In this review, the recent research using monolithic materials in the field of bi

  8. Bioaffinity chromatography on monolithic supports

    NARCIS (Netherlands)

    Tetala, K.K.R.; Beek, van T.A.

    2010-01-01

    Affinity chromatography on monolithic supports is a powerful analytical chemical platform because it allows for fast analyses, small sample volumes, strong enrichment of trace biomarkers and applications in microchips. In this review, the recent research using monolithic materials in the field of bi

  9. Design of monoliths through their mechanical properties.

    Science.gov (United States)

    Podgornik, Aleš; Savnik, Aleš; Jančar, Janez; Krajnc, Nika Lendero

    2014-03-14

    Chromatographic monoliths have several interesting properties making them attractive supports for analytics but also for purification, especially of large biomolecules and bioassemblies. Although many of monolith features were thoroughly investigated, there is no data available to predict how monolith mechanical properties affect its chromatographic performance. In this work, we investigated the effect of porosity, pore size and chemical modification on methacrylate monolith compression modulus. While a linear correlation between pore size and compression modulus was found, the effect of porosity was highly exponential. Through these correlations it was concluded that chemical modification affects monolith porosity without changing the monolith skeleton integrity. Mathematical model to describe the change of monolith permeability as a function of monolith compression modulus was derived and successfully validated for monoliths of different geometries and pore sizes. It enables the prediction of pressure drop increase due to monolith compressibility for any monolith structural characteristics, such as geometry, porosity, pore size or mobile phase properties like viscosity or flow rate, based solely on the data of compression modulus and structural data of non-compressed monolith. Furthermore, it enables simple determination of monolith pore size at which monolith compressibility is the smallest and the most robust performance is expected. Data of monolith compression modulus in combination with developed mathematical model can therefore be used for the prediction of monolith permeability during its implementation but also to accelerate the design of novel chromatographic monoliths with desired hydrodynamic properties for particular application.

  10. Porous polymer monolithic col

    Directory of Open Access Journals (Sweden)

    Lydia Terborg

    2015-05-01

    Full Text Available A new approach has been developed for the preparation of mixed-mode stationary phases to separate proteins. The pore surface of monolithic poly(glycidyl methacrylate-co-ethylene dimethacrylate capillary columns was functionalized with thiols and coated with gold nanoparticles. The final mixed mode surface chemistry was formed by attaching, in a single step, alkanethiols, mercaptoalkanoic acids, and their mixtures on the free surface of attached gold nanoparticles. Use of these mixtures allowed fine tuning of the hydrophobic/hydrophilic balance. The amount of attached gold nanoparticles according to thermal gravimetric analysis was 44.8 wt.%. This value together with results of frontal elution enabled calculation of surface coverage with the alkanethiol and mercaptoalkanoic acid ligands. Interestingly, alkanethiols coverage in a range of 4.46–4.51 molecules/nm2 significantly exceeded that of mercaptoalkanoic acids with 2.39–2.45 molecules/nm2. The mixed mode character of these monolithic stationary phases was for the first time demonstrated in the separations of proteins that could be achieved in the same column using gradient elution conditions typical of reverse phase (using gradient of acetonitrile in water and ion exchange chromatographic modes (applying gradient of salt in water, respectively.

  11. Biobased monoliths for adenovirus purification.

    Science.gov (United States)

    Fernandes, Cláudia S M; Gonçalves, Bianca; Sousa, Margarida; Martins, Duarte L; Barroso, Telma; Pina, Ana Sofia; Peixoto, Cristina; Aguiar-Ricardo, Ana; Roque, A Cecília A

    2015-04-01

    Adenoviruses are important platforms for vaccine development and vectors for gene therapy, increasing the demand for high titers of purified viral preparations. Monoliths are macroporous supports regarded as ideal for the purification of macromolecular complexes, including viral particles. Although common monoliths are based on synthetic polymers as methacrylates, we explored the potential of biopolymers processed by clean technologies to produce monoliths for adenovirus purification. Such an approach enables the development of disposable and biodegradable matrices for bioprocessing. A total of 20 monoliths were produced from different biopolymers (chitosan, agarose, and dextran), employing two distinct temperatures during the freezing process (-20 °C and -80 °C). The morphological and physical properties of the structures were thoroughly characterized. The monoliths presenting higher robustness and permeability rates were further analyzed for the nonspecific binding of Adenovirus serotype 5 (Ad5) preparations. The matrices presenting lower nonspecific Ad5 binding were further functionalized with quaternary amine anion-exchange ligand glycidyltrimethylammonium chloride hydrochloride by two distinct methods, and their performance toward Ad5 purification was assessed. The monolith composed of chitosan and poly(vinyl) alcohol (50:50) prepared at -80 °C allowed 100% recovery of Ad5 particles bound to the support. This is the first report of the successful purification of adenovirus using monoliths obtained from biopolymers processed by clean technologies.

  12. Monolithic microchannel heatsink

    Science.gov (United States)

    Benett, William J.; Beach, Raymond J.; Ciarlo, Dino R.

    1996-01-01

    A silicon wafer has slots sawn in it that allow diode laser bars to be mounted in contact with the silicon. Microchannels are etched into the back of the wafer to provide cooling of the diode bars. To facilitate getting the channels close to the diode bars, the channels are rotated from an angle perpendicular to the diode bars which allows increased penetration between the mounted diode bars. This invention enables the fabrication of monolithic silicon microchannel heatsinks for laser diodes. The heatsinks have low thermal resistance because of the close proximity of the microchannels to the laser diode being cooled. This allows high average power operation of two-dimensional laser diode arrays that have a high density of laser diode bars and therefore high optical power density.

  13. In situ Fabrication of Monolithic Copper Azide

    Science.gov (United States)

    Li, Bing; Li, Mingyu; Zeng, Qingxuan; Wu, Xingyu

    2016-04-01

    Fabrication and characterization of monolithic copper azide were performed. The monolithic nanoporous copper (NPC) with interconnected pores and nanoparticles was prepared by decomposition and sintering of the ultrafine copper oxalate. The preferable monolithic NPC can be obtained through decomposition and sintering at 400°C for 30 min. Then, the available monolithic NPC was in situ reacted with the gaseous HN3 for 24 h and the monolithic NPC was transformed into monolithic copper azide. Additionally, the copper particles prepared by electrodeposition were also reacted with the gaseous HN3 under uniform conditions as a comparison. The fabricated monolithic copper azide was characterized by Fourier transform infrared (FTIR), inductively coupled plasma-optical emission spectrometry (ICP-OES), and differential scanning calorimetry (DSC).

  14. Monolithic Fuel Fabrication Process Development

    Energy Technology Data Exchange (ETDEWEB)

    C. R. Clark; N. P. Hallinan; J. F. Jue; D. D. Keiser; J. M. Wight

    2006-05-01

    The pursuit of a high uranium density research reactor fuel plate has led to monolithic fuel, which possesses the greatest possible uranium density in the fuel region. Process developments in fabrication development include friction stir welding tool geometry and cooling improvements and a reduction in the length of time required to complete the transient liquid phase bonding process. Annealing effects on the microstructures of the U-10Mo foil and friction stir welded aluminum 6061 cladding are also examined.

  15. FLUIDIZED BED STEAM REFORMING MINERALIZATION FOR HIGH ORGANIC AND NITRATE WASTE STREAMS FOR THE GLOBAL NUCLEAR ENERGY PARTNERSHIP

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C; Michael Williams, M

    2008-01-11

    Waste streams that may be generated by the Global Nuclear Energy Partnership (GNEP) Advanced Energy Initiative may contain significant quantities of organics (0-53 wt%) and/or nitrates (0-56 wt%). Decomposition of high nitrate streams requires reducing conditions, e.g. organic additives such as sugar or coal, to reduce the NO{sub x} in the off-gas to N{sub 2} to meet the Clean Air Act (CAA) standards during processing. Thus, organics will be present during waste form stabilization regardless of which GNEP processes are chosen, e.g. organics in the feed or organics for nitrate destruction. High organic containing wastes cannot be stabilized with the existing HLW Best Developed Available Technology (BDAT) which is HLW vitrification (HLVIT) unless the organics are removed by preprocessing. Alternative waste stabilization processes such as Fluidized Bed Steam Reforming (FBSR) operate at moderate temperatures (650-750 C) compared to vitrification (1150-1300 C). FBSR converts organics to CAA compliant gases, creates no secondary liquid waste streams, and creates a stable mineral waste form that is as durable as glass. For application to the high Cs-137 and Sr-90 containing GNEP waste streams a single phase mineralized Cs-mica phase was made by co-reacting illite clay and GNEP simulated waste. The Cs-mica accommodates up to 30% wt% Cs{sub 2}O and all the GNEP waste species, Ba, Sr, Rb including the Cs-137 transmutation to Ba-137. For reference, the cesium mineral pollucite (CsAlSi{sub 2}O{sub 6}), currently being studied for GNEP applications, can only be fabricated at {ge} 1000 C. Pollucite mineralization creates secondary aqueous waste streams and NO{sub x}. Pollucite is not tolerant of high concentrations of Ba, Sr or Rb and forces the divalent species into different mineral host phases. The pollucite can accommodate up to 33% wt% Cs{sub 2}O.

  16. Pressure drop in CIM disk monolithic columns.

    Science.gov (United States)

    Mihelic, Igor; Nemec, Damjan; Podgornik, Ales; Koloini, Tine

    2005-02-11

    Pressure drop analysis in commercial CIM disk monolithic columns is presented. Experimental measurements of pressure drop are compared to hydrodynamic models usually employed for prediction of pressure drop in packed beds, e.g. free surface model and capillary model applying hydraulic radius concept. However, the comparison between pressure drop in monolith and adequate packed bed give unexpected results. Pressure drop in a CIM disk monolithic column is approximately 50% lower than in an adequate packed bed of spheres having the same hydraulic radius as CIM disk monolith; meaning they both have the same porosity and the same specific surface area. This phenomenon seems to be a consequence of the monolithic porous structure which is quite different in terms of the pore size distribution and parallel pore nonuniformity compared to the one in conventional packed beds. The number of self-similar levels for the CIM monoliths was estimated to be between 1.03 and 2.75.

  17. Graphene-supported metal oxide monolith

    Energy Technology Data Exchange (ETDEWEB)

    Worsley, Marcus A.; Baumann, Theodore F.; Biener, Juergen; Biener, Monika A.; Wang, Yinmin; Ye, Jianchao; Tylski, Elijah

    2017-01-10

    A composition comprising at least one graphene-supported metal oxide monolith, said monolith comprising a three-dimensional structure of graphene sheets crosslinked by covalent carbon bonds, wherein the graphene sheets are coated by at least one metal oxide such as iron oxide or titanium oxide. Also provided is an electrode comprising the aforementioned graphene-supported metal oxide monolith, wherein the electrode can be substantially free of any carbon-black and substantially free of any binder.

  18. Graphene-supported metal oxide monolith

    Science.gov (United States)

    Worsley, Marcus A.; Baumann, Theodore F.; Biener, Juergen; Biener, Monika A.; Wang, Yinmin; Ye, Jianchao; Tylski, Elijah

    2017-01-10

    A composition comprising at least one graphene-supported metal oxide monolith, said monolith comprising a three-dimensional structure of graphene sheets crosslinked by covalent carbon bonds, wherein the graphene sheets are coated by at least one metal oxide such as iron oxide or titanium oxide. Also provided is an electrode comprising the aforementioned graphene-supported metal oxide monolith, wherein the electrode can be substantially free of any carbon-black and substantially free of any binder.

  19. Development and Investigation of Evacuated Windows Based on Monolithic Silica Xerogel Spacers

    DEFF Research Database (Denmark)

    Schultz, Jørgen Munthe; Svendsen, Sv Aa Højgaard

    The objective of the project is to develop and investigate insulating glazings based on evacuated monolithic silica xerogel spacers. Since the starting date January 1, 1994 the project has been closely connected to the parallel project "Development and Investigation of Evacuated Windows based...... will be approximately 0.013 W/(m K) which is approximately 33% of the value for commonly used insulation materials, e.g. mineral wool. Monolithic silica xerogel is a highly porous material (pore volume up to 90%) with a solar transmittance of 50% (thickness = 20 mm). However, if the silica xerogel is not made...... and 3) application for insulating glazings.Scientific developments have made it possible to prepare low density monolithic silica xerogels, only from about 1990, and developments in both the production process as well as size of the samples are necessary for a commercial use of the material...

  20. Effects of vanadium (V) and magnesium (Mg) on rat bone tissue: mineral status and micromorphology. Consequences of V-Mg interactions.

    Science.gov (United States)

    Scibior, Agnieszka; Adamczyk, Agnieszka; Mroczka, Robert; Niedźwiecka, Irmina; Gołębiowska, Dorota; Fornal, Emilia

    2014-12-01

    The extent to which the 12 week separate and combined administration of vanadium (as sodium metavanadate--SMV, 0.125 mg V per ml) and magnesium (as magnesium sulphate--MS, 0.06 mg Mg per ml) affects bone mineral status and micromorphology as well as the alkaline phosphatase (ALP) activity in femoral diaphysis (FD) was examined in male rats. The bone chemical composition of SMV-exposed rats was also investigated. SMV alone or in combination with MS (as SMV-MS) reduced the levels of MgFD (by 21% and 20%) and PFD (by 12% and 9%), lowered the CaFD content (by 7% and 10%), and caused a rise of the FeFD concentration (by 22.5% and 17%), compared with the control; SMV alone also reduced and enhanced the KFD and ZnFD concentrations (by 19% and 15%, respectively) but remained without significant effect on the femoral bone surface roughness (FBSR), whereas MS alone lowered the VFD, PFD, and CuFD levels (by 42%, 10%, and 20.6%), reduced FBSR, and created the regular femoral bone surface shape. The SMV-MS combination also induced a decline and rise in the levels of CuFD (by 30%) and NaFD (by 15%), respectively, compared with the control and the MS-supplemented rats; elevated ALPFD activity (by 24%, 35%, and 40%), compared with the control, SMV-exposed, and MS-supplemented animals; and increased FBSR. Relationships between the root mean square roughness (Sq) and skewness (Ssk): Sq [MS Control > SMV > MS], ALPFD and Sq: ALPFD⇔ Sq [SMV-MS > Control > SMV > MS], and between other variables were demonstrated. A partial limitation of the drop in the PFD and KFD levels and normalization of the ZnFD concentration were a consequence of the V-Mg antagonistic interaction whereas a consequence of the V-Mg synergistic interaction was the increase in the NaFD level, ALPFD activity, and FBSR. Ca10(PO4)5(SiO4)(OH) was part of the inorganic component of the bone of the SMV-exposed rats.

  1. Monolithically integrated absolute frequency comb laser system

    Energy Technology Data Exchange (ETDEWEB)

    Wanke, Michael C.

    2016-07-12

    Rather than down-convert optical frequencies, a QCL laser system directly generates a THz frequency comb in a compact monolithically integrated chip that can be locked to an absolute frequency without the need of a frequency-comb synthesizer. The monolithic, absolute frequency comb can provide a THz frequency reference and tool for high-resolution broad band spectroscopy.

  2. Nanosecond monolithic CMOS readout cell

    Science.gov (United States)

    Souchkov, Vitali V.

    2004-08-24

    A pulse shaper is implemented in monolithic CMOS with a delay unit formed of a unity gain buffer. The shaper is formed of a difference amplifier having one input connected directly to an input signal and a second input connected to a delayed input signal through the buffer. An elementary cell is based on the pulse shaper and a timing circuit which gates the output of an integrator connected to the pulse shaper output. A detector readout system is formed of a plurality of elementary cells, each connected to a pixel of a pixel array, or to a microstrip of a plurality of microstrips, or to a detector segment.

  3. Compact monolithic capacitive discharge unit

    Science.gov (United States)

    Roesler, Alexander W.; Vernon, George E.; Hoke, Darren A.; De Marquis, Virginia K.; Harris, Steven M.

    2007-06-26

    A compact monolithic capacitive discharge unit (CDU) is disclosed in which a thyristor switch and a flyback charging circuit are both sandwiched about a ceramic energy storage capacitor. The result is a compact rugged assembly which provides a low-inductance current discharge path. The flyback charging circuit preferably includes a low-temperature co-fired ceramic transformer. The CDU can further include one or more ceramic substrates for enclosing the thyristor switch and for holding various passive components used in the flyback charging circuit. A load such as a detonator can also be attached directly to the CDU.

  4. Microfluidic devices and methods including porous polymer monoliths

    Science.gov (United States)

    Hatch, Anson V; Sommer, Gregory J; Singh, Anup K; Wang, Ying-Chih; Abhyankar, Vinay V

    2014-04-22

    Microfluidic devices and methods including porous polymer monoliths are described. Polymerization techniques may be used to generate porous polymer monoliths having pores defined by a liquid component of a fluid mixture. The fluid mixture may contain iniferters and the resulting porous polymer monolith may include surfaces terminated with iniferter species. Capture molecules may then be grafted to the monolith pores.

  5. Monolithic Continuous-Flow Bioreactors

    Science.gov (United States)

    Stephanopoulos, Gregory; Kornfield, Julia A.; Voecks, Gerald A.

    1993-01-01

    Monolithic ceramic matrices containing many small flow passages useful as continuous-flow bioreactors. Ceramic matrix containing passages made by extruding and firing suitable ceramic. Pores in matrix provide attachment medium for film of cells and allow free movement of solution. Material one not toxic to micro-organisms grown in reactor. In reactor, liquid nutrients flow over, and liquid reaction products flow from, cell culture immobilized in one set of channels while oxygen flows to, and gaseous reaction products flow from, culture in adjacent set of passages. Cells live on inner surfaces containing flowing nutrient and in pores of walls of passages. Ready access to nutrients and oxygen in channels. They generate continuous high yield characteristic of immobilized cells, without large expenditure of energy otherwise incurred if necessary to pump nutrient solution through dense biomass as in bioreactors of other types.

  6. Anisotropically structured magnetic aerogel monoliths

    Science.gov (United States)

    Heiligtag, Florian J.; Airaghi Leccardi, Marta J. I.; Erdem, Derya; Süess, Martin J.; Niederberger, Markus

    2014-10-01

    Texturing of magnetic ceramics and composites by aligning and fixing of colloidal particles in a magnetic field is a powerful strategy to induce anisotropic chemical, physical and especially mechanical properties into bulk materials. If porosity could be introduced, anisotropically structured magnetic materials would be the perfect supports for magnetic separations in biotechnology or for magnetic field-assisted chemical reactions. Aerogels, combining high porosity with nanoscale structural features, offer an exceptionally large surface area, but they are difficult to magnetically texture. Here we present the preparation of anatase-magnetite aerogel monoliths via the assembly of preformed nanocrystallites. Different approaches are proposed to produce macroscopic bodies with gradient-like magnetic segmentation or with strongly anisotropic magnetic texture.Texturing of magnetic ceramics and composites by aligning and fixing of colloidal particles in a magnetic field is a powerful strategy to induce anisotropic chemical, physical and especially mechanical properties into bulk materials. If porosity could be introduced, anisotropically structured magnetic materials would be the perfect supports for magnetic separations in biotechnology or for magnetic field-assisted chemical reactions. Aerogels, combining high porosity with nanoscale structural features, offer an exceptionally large surface area, but they are difficult to magnetically texture. Here we present the preparation of anatase-magnetite aerogel monoliths via the assembly of preformed nanocrystallites. Different approaches are proposed to produce macroscopic bodies with gradient-like magnetic segmentation or with strongly anisotropic magnetic texture. Electronic supplementary information (ESI) available: Digital photographs of dispersions and gels with different water-to-ethanol ratios; magnetic measurements of an anatase aerogel containing 0.25 mol% Fe3O4 nanoparticles; XRD patterns of the iron oxide and

  7. Monolithic cells for solar fuels.

    Science.gov (United States)

    Rongé, Jan; Bosserez, Tom; Martel, David; Nervi, Carlo; Boarino, Luca; Taulelle, Francis; Decher, Gero; Bordiga, Silvia; Martens, Johan A

    2014-12-07

    Hybrid energy generation models based on a variety of alternative energy supply technologies are considered the best way to cope with the depletion of fossil energy resources and to limit global warming. One of the currently missing technologies is the mimic of natural photosynthesis to convert carbon dioxide and water into chemical fuel using sunlight. This idea has been around for decades, but artificial photosynthesis of organic molecules is still far away from providing real-world solutions. The scientific challenge is to perform in an efficient way the multi-electron transfer reactions of water oxidation and carbon dioxide reduction using holes and single electrons generated in an illuminated semiconductor. In this tutorial review the design of photoelectrochemical (PEC) cells that combine solar water oxidation and CO2 reduction is discussed. In such PEC cells simultaneous transport and efficient use of light, electrons, protons and molecules has to be managed. It is explained how efficiency can be gained by compartmentalisation of the water oxidation and CO2 reduction processes by proton exchange membranes, and monolithic concepts of artificial leaves and solar membranes are presented. Besides transferring protons from the anode to the cathode compartment the membrane serves as a molecular barrier material to prevent cross-over of oxygen and fuel molecules. Innovative nano-organized multimaterials will be needed to realise practical artificial photosynthesis devices. This review provides an overview of synthesis techniques which could be used to realise monolithic multifunctional membrane-electrode assemblies, such as Layer-by-Layer (LbL) deposition, Atomic Layer Deposition (ALD), and porous silicon (porSi) engineering. Advances in modelling approaches, electrochemical techniques and in situ spectroscopies to characterise overall PEC cell performance are discussed.

  8. Monolithic Time Delay Integrated APD Arrays Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The overall goal of the proposed program by Epitaxial Technologies is to develop monolithic time delay integrated avalanche photodiode (APD) arrays with sensitivity...

  9. Monolithic multinozzle emitters for nanoelectrospray mass spectrometry

    Science.gov (United States)

    Wang, Daojing; Yang, Peidong; Kim, Woong; Fan, Rong

    2011-09-20

    Novel and significantly simplified procedures for fabrication of fully integrated nanoelectrospray emitters have been described. For nanofabricated monolithic multinozzle emitters (NM.sup.2 emitters), a bottom up approach using silicon nanowires on a silicon sliver is used. For microfabricated monolithic multinozzle emitters (M.sup.3 emitters), a top down approach using MEMS techniques on silicon wafers is used. The emitters have performance comparable to that of commercially-available silica capillary emitters for nanoelectrospray mass spectrometry.

  10. Activated Carbon Fiber Monoliths as Supercapacitor Electrodes

    Directory of Open Access Journals (Sweden)

    Gelines Moreno-Fernandez

    2017-01-01

    Full Text Available Activated carbon fibers (ACF are interesting candidates for electrodes in electrochemical energy storage devices; however, one major drawback for practical application is their low density. In the present work, monoliths were synthesized from two different ACFs, reaching 3 times higher densities than the original ACFs’ apparent densities. The porosity of the monoliths was only slightly decreased with respect to the pristine ACFs, the employed PVDC binder developing additional porosity upon carbonization. The ACF monoliths are essentially microporous and reach BET surface areas of up to 1838 m2 g−1. SEM analysis reveals that the ACFs are well embedded into the monolith structure and that their length was significantly reduced due to the monolith preparation process. The carbonized monoliths were studied as supercapacitor electrodes in two- and three-electrode cells having 2 M H2SO4 as electrolyte. Maximum capacitances of around 200 F g−1 were reached. The results confirm that the capacitance of the bisulfate anions essentially originates from the double layer, while hydronium cations contribute with a mixture of both, double layer capacitance and pseudocapacitance.

  11. Collagen-biomorphic porous carbon nanofiber monoliths: Biosilicification-assisted sustainable synthesis and application in Li-S battery

    Science.gov (United States)

    Hu, Wen; Shen, Tao; Hou, Hongying; Gan, Guoyou; Zheng, Biju; Li, Fengxian; Yi, Jianhong

    2016-12-01

    Monolithic carbon has been synthesized via a sustainable biomimetic route utilizing intrafibrillar silicified collagen sponge as precursor and morphogenesis template. The mineralized silica in the biohybrid prevents collapse of the carbon during pyrolysis. Upon biosilica removal results show that the carbon monoliths inherit the porous fiber structure of the mother collagen. The carbon nanofiber framework facilitates the construction of a high electrical conductive pathway, while the internal spaces developed among the intertwined fibrillar network and pores within nanofiber walls offer room for sulfur storage. The as-obtained carbon-sulfur cathode exhibits an accessible discharge capacity approaching 800mAh g-1 in Li-S battery.

  12. Monolithically integrated Ge CMOS laser

    Science.gov (United States)

    Camacho-Aguilera, Rodolfo

    2014-02-01

    Ge-on-Si devices are explored for photonic integration. Through the development of better growth techniques, monolithic integration, laser design and prototypes, it was possible to probe Ge light emitters with emphasis on lasers. Preliminary worked shows thermal photonic behavior capable of enhancing lamination at high temperatures. Increase luminescence is observed up to 120°C from L-band contribution. Higher temperatures show contribution from Δ -band. The increase carrier thermal contribution suggests high temperature applications for Ge light emitters. A Ge electrically pumped laser was probed under 0.2% biaxial strain and doping concentration ~4.5×1019cm-3 n-type. Ge pnn lasers exhibit a gain >1000cm-1 with 8mW power output, presenting a spectrum range of over 200nm, making Ge the ideal candidate for Si photonics. Large temperatures fluctuations and process limit the present device. Theoretically a gain of >4000cm- gain is possible with a threshold of as low as 1kA/cm2. Improvements in Ge work

  13. Modified monolithic silica capillary for preconcentration of catecholamines

    Institute of Scientific and Technical Information of China (English)

    Wei Chang; Tusyo-shi Komazu

    2009-01-01

    Preconcentration of catecholamines by the modified monolithic silica in the capillary was investigated in this study. In order to achieve a microchip-based method for determining catecholamines in the saliva, the monolithic silica was fabricated in the capillary and the monolithic silica was chemically modified by on-column reaction with phenylboronate. Different modified methods were compared. The concentration conditions were optimized. This study indicates the applicability of the modified monolithic silica capillary when it was used to concentrate catecholamines.

  14. Modified monolithic silica capillary for preconcentration of catecholamines

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Preconcentration of catecholamines by the modified monolithic silica in the capillary was investigated in this study. In order to achieve a microchip-based method for determining catecholamines in the saliva,the monolithic silica was fabricated in the capillary and the monolithic silica was chemically modified by on-column reaction with phenylboronate. Different modified methods were compared. The concentration conditions were optimized. This study indicates the applicability of the modified monolithic sili...

  15. Fracture resistance of monolithic zirconia molar crowns with reduced thickness

    OpenAIRE

    Nakamura, Keisuke; Harada, A.; Inagaki, R.; Kanno, Taro; Niwano, Y; Milleding, Percy; Ørtengren, Ulf Thore

    2015-01-01

    This is the accepted manuscript version. Published version is available at Acta Odontologica Scandinavica Objectives. The purpose of the present study was to analyze the relationship between fracture load of monolithic zirconia crowns and axial/occlusal thickness, and to evaluate the fracture resistance of monolithic zirconia crowns with reduced thickness in comparison with that of monolithic lithium disilicate crowns with regular thickness. Materials and methods. Monolithic zi...

  16. Development of a monolithic ferrite memory array

    Science.gov (United States)

    Heckler, C. H., Jr.; Bhiwandker, N. C.

    1972-01-01

    The results of the development and testing of ferrite monolithic memory arrays are presented. This development required the synthesis of ferrite materials having special magnetic and physical characteristics and the development of special processes; (1) for making flexible sheets (laminae) of the ferrite composition, (2) for embedding conductors in ferrite, and (3) bonding ferrite laminae together to form a monolithic structure. Major problems encountered in each of these areas and their solutions are discussed. Twenty-two full-size arrays were fabricated and fired during the development of these processes. The majority of these arrays were tested for their memory characteristics as well as for their physical characteristics and the results are presented. The arrays produced during this program meet the essential goals and demonstrate the feasibility of fabricating monolithic ferrite memory arrays by the processes developed.

  17. Carbon Fiber Composite Monoliths as Catalyst Supports

    Energy Technology Data Exchange (ETDEWEB)

    Contescu, Cristian I [ORNL; Gallego, Nidia C [ORNL; Pickel, Joseph M [ORNL; Blom, Douglas Allen [ORNL; Burchell, Timothy D [ORNL

    2006-01-01

    Carbon fiber composite monoliths are rigid bodies that can be activated to a large surface area, have tunable porosity, and proven performance in gas separation and storage. They are ideal as catalyst supports in applications where a rigid support, with open structure and easy fluid access is desired. We developed a procedure for depositing a dispersed nanoparticulate phase of molybdenum carbide (Mo2C) on carbon composite monoliths in the concentration range of 3 to 15 wt% Mo. The composition and morphology of this phase was characterized using X-ray diffraction and electron microscopy, and a mechanism was suggested for its formation. Molybdenum carbide is known for its catalytic properties that resemble those of platinum group metals, but at a lower cost. The materials obtained are expected to demonstrate catalytic activity in a series of hydrocarbon reactions involving hydrogen transfer. This project demonstrates the potential of carbon fiber composite monoliths as catalyst supports.

  18. Carbon Fiber Composite Monoliths for Catalyst Supports

    Energy Technology Data Exchange (ETDEWEB)

    Contescu, Cristian I [ORNL; Gallego, Nidia C [ORNL; Pickel, Joseph M [ORNL; Blom, Douglas Allen [ORNL; Burchell, Timothy D [ORNL

    2006-01-01

    Carbon fiber composite monoliths are rigid bodies that can be activated to a large surface area, have tunable porosity, and proven performance in gas separation and storage. They are ideal as catalyst supports in applications where a rigid support, with open structure and easy fluid access is desired. We developed a procedure for depositing a dispersed nanoparticulate phase of molybdenum carbide (Mo2C) on carbon composite monoliths in the concentration range of 3 to 15 wt% Mo. The composition and morphology of this phase was characterized using X-ray diffraction and electron microscopy, and a mechanism was suggested for its formation. Molybdenum carbide is known for its catalytic properties that resemble those of platinum group metals, but at a lower cost. The materials obtained are expected to demonstrate catalytic activity in a series of hydrocarbon reactions involving hydrogen transfer. This project demonstrates the potential of carbon fiber composite monoliths as catalyst supports.

  19. Eigenpolarization theory of monolithic nonplanar ring oscillators

    Science.gov (United States)

    Nilsson, Alan C.; Gustafson, Eric K.; Byer, Robert L.

    1989-01-01

    Diode-laser-pumped monolithic nonplanar ring oscillators (NPROs) in an applied magnetic field can operate as unidirectional traveling-wave lasers. The diode laser pumping, monolithic construction, and unidirectional oscillation lead to narrow linewidth radiation. Here, a comprehensive theory of the eigenpolarizations of a monolithic NPRO is presented. It is shown how the properties of the integral optical diode that forces unidirectional operation depend on the choice of the gain medium, the applied magnetic field, the output coupler, and the geometry of the nonplanar ring light path. Using optical equivalence theorems to gain insight into the polarization characteristics of the NPRO, a strategy for designing NPROs with low thresholds and large loss nonreciprocities is given. An analysis of the eigenpolarizations for one such NPRO is presented, alternative optimization approaches are considered, and the prospects for further reducing the linewidths of these lasers are briefly discussed.

  20. Physical and chemical sensing using monolithic semiconductor optical transducers

    Science.gov (United States)

    Zappe, Hans P.; Hofstetter, Daniel; Maisenhoelder, Bernd; Moser, Michael; Riel, Peter; Kunz, Rino E.

    1997-09-01

    We present two monolithically integrated optical sensor systems based on semiconductor photonic integrated circuits. These compact, robust and highly functional transducers perform all necessary optical and electro-optical functions on-chip; extension to multi-sensor arrays is easily envisaged. A monolithic Michelson interferometer for high-resolution displacement measurement and a monolithic Mach-Zehnder interferometer for refractometry are discussed.

  1. Increased thermal conductivity monolithic zeolite structures

    Science.gov (United States)

    Klett, James; Klett, Lynn; Kaufman, Jonathan

    2008-11-25

    A monolith comprises a zeolite, a thermally conductive carbon, and a binder. The zeolite is included in the form of beads, pellets, powders and mixtures thereof. The thermally conductive carbon can be carbon nano-fibers, diamond or graphite which provide thermal conductivities in excess of about 100 W/mK to more than 1,000 W/mK. A method of preparing a zeolite monolith includes the steps of mixing a zeolite dispersion in an aqueous colloidal silica binder with a dispersion of carbon nano-fibers in water followed by dehydration and curing of the binder is given.

  2. Characterization of CIM monoliths as enzyme reactors.

    Science.gov (United States)

    Vodopivec, Martina; Podgornik, Ales; Berovic, Marin; Strancar, Ales

    2003-09-25

    The immobilization of the enzymes citrate lyase, malate dehydrogenase, isocitrate dehydrogenase and lactate dehydrogenase to CIM monolithic supports was performed. The long-term stability, reproducibility, and linear response range of the immobilized enzyme reactors were investigated along with the determination of the kinetic behavior of the enzymes immobilized on the CIM monoliths. The Michaelis-Menten constant K(m) and the turnover number k(3) of the immobilized enzymes were found to be flow-unaffected. Furthermore, the K(m) values of the soluble and immobilized enzyme were found to be comparable. Both facts indicate the absence of a diffusional limitation in immobilized CIM enzyme reactors.

  3. Monolithically integrated optoelectronic down-converter (MIOD)

    Science.gov (United States)

    Portnoi, Efrim L.; Venus, G. B.; Khazan, A. A.; Gorfinkel, Vera B.; Kompa, Guenter; Avrutin, Evgenii A.; Thayne, Iain G.; Barrow, David A.; Marsh, John H.

    1995-06-01

    Optoelectronic down-conversion of very high-frequency amplitude-modulated signals using a semiconductor laser simultaneously as a local oscillator and a mixer is proposed. Three possible constructions of a monolithically integrated down-converter are considered theoretically: a four-terminal semiconductor laser with dual pumping current/modal gain control, and both a passively mode-locked and a passively Q-switched semiconductor laser monolithically integrated with an electroabsorption or pumping current modulator. Experimental verification of the feasibility of the concept of down conversion in a laser diode is presented.

  4. Development and Investigation of Evacuated Windows Based on Monolithic Silica Xerogel Spacers

    DEFF Research Database (Denmark)

    Schultz, Jørgen Munthe; Svendsen, Sv Aa Højgaard

    will be approximately 0.013 W/(m K) which is approximately 33% of the value for commonly used insulation materials, e.g. mineral wool. Monolithic silica xerogel is a highly porous material (pore volume up to 90%) with a solar transmittance of 50% (thickness = 20 mm). However, if the silica xerogel is not made...... and 3) application for insulating glazings.Scientific developments have made it possible to prepare low density monolithic silica xerogels, only from about 1990, and developments in both the production process as well as size of the samples are necessary for a commercial use of the material...... for insulating glazings. Using the material as spacer between two layers of glass with a vacuum tight sealing of the rim combined with an internal gas pressure below 50-100 hPa result in an insulating glazing having a heat loss coefficient comparable with that of the surrounding walls, but at the same time...

  5. Monolithic Integration of GaN-based LEDs

    Energy Technology Data Exchange (ETDEWEB)

    Ao, Jin-Ping, E-mail: jpao@ee.tokushima-u.ac.jp [Institute of Technology and Science, University of Tokushima 2-1 Minami-Josanjima, Tokushima 770-8506 (Japan)

    2011-02-01

    The technology of monolithically integrated GaN-based light-emitting diodes (LEDs) is reported. First, the technology details to realize monolithic integration are described, including the circuit design for high-voltage and alternating current (AC) operation and the technologies for device isolation. The performances of the fabricated monolithic LED arrays are then demonstrated. A monolithic series array with totally 40 LEDs exhibited expected operation function under AC bias. The operation voltage of the array is 72 V when 20 LEDs were connected in series. Some modified circuit designs for high-voltage operation and other monolithic LED arrays are finally reviewed.

  6. Monolithic resonant optical reflector laser diodes

    Science.gov (United States)

    Hirata, T.; Suehiro, M.; Maeda, M.; Hihara, M.; Hosomatsu, H.

    1991-10-01

    The first monolithic resonant optical reflector laser diode that has a waveguide directional coupler and two DBR reflectors integrated by compositional disordering of quantum-well heterostructures is described. A linewidth of 440 kHz was obtained, and this value is expected to be greatly decreased by reducing the propagation loss in the integrated waveguide.

  7. Constant capacitance in nanopores of carbon monoliths.

    Science.gov (United States)

    García-Gómez, Alejandra; Moreno-Fernández, Gelines; Lobato, Belén; Centeno, Teresa A

    2015-06-28

    The results obtained for binder-free electrodes made of carbon monoliths with narrow micropore size distributions confirm that the specific capacitance in the electrolyte (C2H5)4NBF4/acetonitrile does not depend significantly on the micropore size and support the foregoing constant result of 0.094 ± 0.011 F m(-2).

  8. Mineral oils

    Science.gov (United States)

    Furby, N. W.

    1973-01-01

    The characteristics of lubricants made from mineral oils are discussed. Types and compositions of base stocks are reviewed and the product demands and compositions of typical products are outlined. Processes for commercial production of mineral oils are examined. Tables of data are included to show examples of product types and requirements. A chemical analysis of three types of mineral oils is reported.

  9. A monolithic integrated photonic microwave filter

    Science.gov (United States)

    Fandiño, Javier S.; Muñoz, Pascual; Doménech, David; Capmany, José

    2016-12-01

    Meeting the increasing demand for capacity in wireless networks requires the harnessing of higher regions in the radiofrequency spectrum, reducing cell size, as well as more compact, agile and power-efficient base stations that are capable of smoothly interfacing the radio and fibre segments. Fully functional microwave photonic chips are promising candidates in attempts to meet these goals. In recent years, many integrated microwave photonic chips have been reported in different technologies. To the best of our knowledge, none has monolithically integrated all the main active and passive optoelectronic components. Here, we report the first demonstration of a tunable microwave photonics filter that is monolithically integrated into an indium phosphide chip. The reconfigurable radiofrequency photonic filter includes all the necessary elements (for example, lasers, modulators and photodetectors), and its response can be tuned by means of control electric currents. This is an important step in demonstrating the feasibility of integrated and programmable microwave photonic processors.

  10. Macroporous Monolithic Polymers: Preparation and Applications

    Directory of Open Access Journals (Sweden)

    Cecilia Inés Alvarez Igarzabal

    2009-12-01

    Full Text Available In the last years, macroporous monolithic materials have been introduced as a new and useful generation of polymers used in different fields. These polymers may be prepared in a simple way from a homogenous mixture into a mold and contain large interconnected pores or channels allowing for high flow rates at moderate pressures. Due to their porous characteristics, they could be used in different processes, such as stationary phases for different types of chromatography, high-throughput bioreactors and in microfluidic chip applications. This review reports the contributions of several groups working in the preparation of different macroporous monoliths and their modification by immobilization of specific ligands on the products for specific purposes.

  11. Monolithic pixel detectors for high energy physics

    CERN Document Server

    Snoeys, W

    2013-01-01

    Monolithic pixel detectors integrating sensor matrix and readout in one piece of silicon have revolutionized imaging for consumer applications, but despite years of research they have not yet been widely adopted for high energy physics. Two major requirements for this application, radiation tolerance and low power consumption, require charge collection by drift for the most extreme radiation levels and an optimization of the collected signal charge over input capacitance ratio ( Q / C ). It is shown that monolithic detectors can achieve Q / C for low analog power consumption and even carryout the promise to practically eliminate analog power consumption, but combining suf fi cient Q / C , collection by drift, and integration of readout circuitry within the pixel remains a challenge. An overview is given of different approaches to address this challenge, with possible advantages and disadvantages.

  12. Update On Monolithic Fuel Fabrication Development

    Energy Technology Data Exchange (ETDEWEB)

    C. R Clark; J. M. Wight; G. C. Knighton; G. A. Moore; J. F. Jue

    2005-11-01

    Efforts to develop a viable monolithic research reactor fuel plate have continued at Idaho National Laboratory. These efforts have concentrated on both fabrication process refinement and scale-up to produce full sized fuel plates. Advancements have been made in the production of U-Mo foil including full sized foils. Progress has also been made in the friction stir welding and transient liquid phase bonding fabrication processes resulting in better bonding, more stable processes and the ability to fabricate larger fuel plates.

  13. Monolithically integrated interferometer for optical displacement measurement

    Science.gov (United States)

    Hofstetter, Daniel; Zappe, Hans P.

    1996-01-01

    We discuss the fabrication of a monolithically integrated optical displacement sensors using III-V semiconductor technology. The device is configured as a Michelson interferometer and consists of a distributed Bragg reflector laser, a photodetector and waveguides forming a directional coupler. Using this interferometer, displacements in the 100 nm range could be measured at distances of up to 45 cm. We present fabrication, device results and characterization of the completed interferometer, problems, limitations and future applications will also be discussed.

  14. An overview of monolithic zirconia in dentistry

    Directory of Open Access Journals (Sweden)

    Özlem Malkondu

    2016-07-01

    Full Text Available Zirconia restorations have been used successfully for years in dentistry owing to their biocompatibility and good mechanical properties. Because of their lack of translucency, zirconia cores are generally veneered with porcelain, which makes restorations weaker due to failure of the adhesion between the two materials. In recent years, all-ceramic zirconia restorations have been introduced in the dental sector with the intent to solve this problem. Besides the elimination of chipping, the reduced occlusal space requirement seems to be a clear advantage of monolithic zirconia restorations. However, scientific evidence is needed to recommend this relatively new application for clinical use. This mini-review discusses the current scientific literature on monolithic zirconia restorations. The results of in vitro studies suggested that monolithic zirconia may be the best choice for posterior fixed partial dentures in the presence of high occlusal loads and minimal occlusal restoration space. The results should be supported with much more in vitro and particularly in vivo studies to obtain a final conclusion.

  15. Preparation of imprinted monolithic column under molecular crowding conditions

    Institute of Scientific and Technical Information of China (English)

    Xiao Xia Li; Xin Liu; Li Hong Bai; Hong Quan Duan; Yan Ping Huang; Zhao Sheng Liu

    2011-01-01

    Molecular crowding is a new concept to obtain molecularly imprinted polymers (MIPs) with greater capacity and selectivity. In this work, molecular crowding agent was firstly applied to the preparation of MIPs monolithic column. A new polymerization system based on molecular crowding surrounding was developed to prepare enrofloxacin-imprinted monolith, which was composed of polystyrene and tetrahydrofuran. The result showed that the monolithic MIPs under molecular crowding conditions presented good molecular recognition for enrofloxacin with an imprinting factor of 3.03.

  16. Monolithic Lumped Element Integrated Circuit (M2LEIC) Transistors.

    Science.gov (United States)

    INTEGRATED CIRCUITS, *MONOLITHIC STRUCTURES(ELECTRONICS), *TRANSISTORS, CHIPS(ELECTRONICS), FABRICATION, EPITAXIAL GROWTH, ULTRAHIGH FREQUENCY, POLYSILICONS, PHOTOLITHOGRAPHY, RADIOFREQUENCY POWER, IMPEDANCE MATCHING .

  17. Selective oxidation of cyclohexene through gold functionalized silica monolith microreactors

    Science.gov (United States)

    Alotaibi, Mohammed T.; Taylor, Martin J.; Liu, Dan; Beaumont, Simon K.; Kyriakou, Georgios

    2016-04-01

    Two simple, reproducible methods of preparing evenly distributed Au nanoparticle containing mesoporous silica monoliths are investigated. These Au nanoparticle containing monoliths are subsequently investigated as flow reactors for the selective oxidation of cyclohexene. In the first strategy, the silica monolith was directly impregnated with Au nanoparticles during the formation of the monolith. The second approach was to pre-functionalize the monolith with thiol groups tethered within the silica mesostructure. These can act as evenly distributed anchors for the Au nanoparticles to be incorporated by flowing a Au nanoparticle solution through the thiol functionalized monolith. Both methods led to successfully achieving even distribution of Au nanoparticles along the length of the monolith as demonstrated by ICP-OES. However, the impregnation method led to strong agglomeration of the Au nanoparticles during subsequent heating steps while the thiol anchoring procedure maintained the nanoparticles in the range of 6.8 ± 1.4 nm. Both Au nanoparticle containing monoliths as well as samples with no Au incorporated were tested for the selective oxidation of cyclohexene under constant flow at 30 °C. The Au free materials were found to be catalytically inactive with Au being the minimum necessary requirement for the reaction to proceed. The impregnated Au-containing monolith was found to be less active than the thiol functionalized Au-containing material, attributable to the low metal surface area of the Au nanoparticles. The reaction on the thiol functionalized Au-containing monolith was found to depend strongly on the type of oxidant used: tert-butyl hydroperoxide (TBHP) was more active than H2O2, likely due to the thiol induced hydrophobicity in the monolith.

  18. Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders

    NARCIS (Netherlands)

    De Kanter, J.L.C.G.

    2006-01-01

    Summary accompanying the thesis: Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders by Jens de Kanter This thesis presents the investigation of the crush behaviour of both monolithic aluminium cylinders and externally fibre reinforced aluminium cylinders. The research is based

  19. Time-based position estimation in monolithic scintillator detectors

    NARCIS (Netherlands)

    Tabacchini, V.; Borghi, G.; Schaart, D.R.

    2015-01-01

    Gamma-ray detectors based on bright monolithic scintillation crystals coupled to pixelated photodetectors are currently being considered for several applications in the medical imaging field. In a typical monolithic detector, both the light intensity and the time of arrival of the earliest

  20. Time-based position estimation in monolithic scintillator detectors

    NARCIS (Netherlands)

    Tabacchini, V.; Borghi, G.; Schaart, D.R.

    2015-01-01

    Gamma-ray detectors based on bright monolithic scintillation crystals coupled to pixelated photodetectors are currently being considered for several applications in the medical imaging field. In a typical monolithic detector, both the light intensity and the time of arrival of the earliest scintilla

  1. Time-based position estimation in monolithic scintillator detectors

    NARCIS (Netherlands)

    Tabacchini, V.; Borghi, G.; Schaart, D.R.

    2015-01-01

    Gamma-ray detectors based on bright monolithic scintillation crystals coupled to pixelated photodetectors are currently being considered for several applications in the medical imaging field. In a typical monolithic detector, both the light intensity and the time of arrival of the earliest scintilla

  2. A Monolithic Perovskite Structure for Use as a Magnetic Regenerator

    DEFF Research Database (Denmark)

    Pryds, Nini; Clemens, Frank; Menon, Mohan

    2011-01-01

    A La0.67Ca0.26Sr0.07Mn1.05O3 (LCSM) perovskite was prepared for the first time as a ceramic monolithic regenerator used in a regenerative magnetic refrigeration device. The parameters influencing the extrusion process and the performance of the regenerator, such as the nature of the monolith paste...

  3. Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders

    NARCIS (Netherlands)

    De Kanter, J.L.C.G.

    2006-01-01

    Summary accompanying the thesis: Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders by Jens de Kanter This thesis presents the investigation of the crush behaviour of both monolithic aluminium cylinders and externally fibre reinforced aluminium cylinders. The research is based

  4. Hydrogel coated monoliths for enzymatic hydrolysis of penicillin G

    NARCIS (Netherlands)

    De Lathouder, K.M.; Smeltink, M.W.; Straathof, A.J.J.; Paasman, M.A.; Van de Sandt, E.J.A.X.; Kapteijn, F.; Moulijn, J.A.

    2008-01-01

    The objective of this work was to develop a hydrogel-coated monolith for the entrapment of penicillin G acylase (E. coli, PGA). After screening of different hydrogels, chitosan was chosen as the carrier material for the preparation of monolithic biocatalysts. This protocol leads to active immobilize

  5. A new large area monolithic silicon telescope

    CERN Document Server

    Tudisco, S; Cabibbo, M; Cardella, G; De Geronimo, G; Di Pietro, A; Fallica, G; Figuera, P; Musumarra, A; Papa, M; Pappalardo, G S; Rizzo, F; Valvo, G

    1999-01-01

    A new prototype of large area (20x20 mm sup 2) monolithic silicon telescope with an ultrathin DELTA E stage (1 mu m) has been built and tested. A particular mask for the ground electrode has been developed to improve the charge collection reducing the induction between the E and DELTA E stages. A special designed preamplifier has been used for the readout of the signal from the DELTA E stage to overcome the problem of the large input capacitance (40 nF). A rather low energy threshold charge discrimination has been obtained. Small side effects due to the electric field deformation near the ground electrode were observed and quantified.

  6. Monolithic aerogels with nanoporous crystalline phases

    Science.gov (United States)

    Daniel, Christophe; Guerra, Gaetano

    2015-05-01

    High porosity monolithic aerogels with nanoporous crystalline phases can be obtained from syndiotactic polystyrene and poly(2,6-dimethyl-1,4-phenylene)oxide thermoreversible gels by removing the solvent with supercritical CO2. The presence of crystalline nanopores in the aerogels based on these polymers allows a high uptake associated with a high selectivity of volatile organic compounds from vapor phase or aqueous solutions even at very low activities. The sorption and the fast kinetics make these materials particularly suitable as sorption medium to remove traces of pollutants from water and moist air.

  7. Monolithic columns in plant proteomics and metabolomics.

    Science.gov (United States)

    Rigobello-Masini, Marilda; Penteado, José Carlos Pires; Masini, Jorge Cesar

    2013-03-01

    Since "omics" techniques emerged, plant studies, from biochemistry to ecology, have become more comprehensive. Plant proteomics and metabolomics enable the construction of databases that, with the help of genomics and informatics, show the data obtained as a system. Thus, all the constituents of the system can be seen with their interactions in both space and time. For instance, perturbations in a plant ecosystem as a consequence of application of herbicides or exposure to pollutants can be predicted by using information gathered from these databases. Analytical chemistry has been involved in this scientific evolution. Proteomics and metabolomics are emerging fields that require separation, identification, and quantification of proteins, peptides, and small molecules of metabolites in complex biological samples. The success of this work relies on efficient chromatographic and electrophoretic techniques, and on mass spectrometric detection. This paper reviews recent developments in the use of monolithic columns, focusing on their applications in "top-down" and "bottom-up" approaches, including their use as supports for immobilization of proteolytic enzymes and their use in two-dimensional and multidimensional chromatography. Whereas polymeric columns have been predominantly used for separation of proteins and polypeptides, silica-based monoliths have been more extensively used for separation of small molecules of metabolites. Representative applications in proteomics and in analysis of plant metabolites are given and summarized in tables.

  8. Growth techniques for monolithic YBCO solenoidal magnets

    Energy Technology Data Exchange (ETDEWEB)

    Scruggs, S.J. [Texas Center for Superconductivity at University of Houston, 4800 Calhoun, Houston, TX 77204 (United States)]. E-mail: Sscruggs2@uh.edu; Putman, P.T. [Texas Center for Superconductivity at University of Houston, 4800 Calhoun, Houston, TX 77204 (United States); Fang, H. [Texas Center for Superconductivity at University of Houston, 4800 Calhoun, Houston, TX 77204 (United States); Alessandrini, M. [Texas Center for Superconductivity at University of Houston, 4800 Calhoun, Houston, TX 77204 (United States); Salama, K. [Texas Center for Superconductivity at University of Houston, 4800 Calhoun, Houston, TX 77204 (United States)

    2006-10-01

    The possibility of growing large single domain YBCO solenoids by the use of a large seed has been investigated. There are two known methods for producing a similar solenoid. This first is a conventional top seeded melt growth process followed by a post processing machining step to create the bore. The second involves using multiple seeds spaced around the magnet bore. The appeal of the new technique lies in decreasing processing time compared to the single seed technique, while avoiding alignment problems found in the multiple seeding technique. By avoiding these problems, larger diameter monoliths can be produced. Large diameter monoliths are beneficial because the maximum magnetic field produced by a trapped field magnet is proportional to the radius of the sample. Furthermore, the availability of trapped field magnets with large diameter could enable their use in applications that traditionally have been considered to require wound electromagnets, such as beam bending magnets for particle accelerators or electric propulsion. A comparison of YBCO solenoids grown by the use of a large seed and grown by the use of two small seeds simulating multiple seeding is made. Trapped field measurements as well as microstructure evaluation were used in characterization of each solenoid. Results indicate that high quality growth occurs only in the vicinity of the seeds for the multiple seeded sample, while the sample with the large seeded exhibited high quality growth throughout the entire sample.

  9. High surface area, high permeability carbon monoliths

    Energy Technology Data Exchange (ETDEWEB)

    Lagasse, R.R.; Schroeder, J.L. [Sandia National Labs., Albuquerque, NM (United States). Organic Materials Processing Dept.

    1994-12-31

    The goal of this work is to prepare carbon monoliths having precisely tailored pore size distribution. Prior studies have demonstrated that poly(acrylonitrile) can be processed into a precursor having tailored macropore structure. Since the macropores were preserved during pyrolysis, this synthetic process provided a route to porous carbon having macropores with size =0.1 to 10{mu}m. No micropores of size <2 nm could be detected in the carbon, however, by nitrogen adsorption. In the present work, the authors have processed a different polymer, poly(vinylidene chloride) into a macroporous precursor, Pyrolysis produced carbon monoliths having macropores derived from the polymer precursor as well as extensive microporosity produced during the pyrolysis of the polymer. One of these carbons had BET surface area of 1,050 m{sup 2}/g and about 1.2 cc/g total pore volume, with about 1/3 of the total pore volume in micropores and the remainder in 1{mu}m macropores. No mesopores in the intermediate size range could be detected by nitrogen adsorption. Carbon materials having high surface area as well as micron size pores have potential applications as electrodes for double layer supercapacitors containing liquid electrolyte, or as efficient media for performing chemical separations.

  10. Hydrothermal method for preparing calcium phosphate monoliths

    Directory of Open Access Journals (Sweden)

    García Carrodeguas Raúl

    2003-01-01

    Full Text Available A new hydrothermal route for preparing biphasic calcium phosphate monoliths is proposed. Firstly, a slurry of beta-tricalcium phosphate/ortho-phosphoric acid (b-TCP/H3PO4 is cast into the desired final shape and size to obtain a block composed of dicalcium phosphate dihydrate (DCPD and b-TCP. This block is then treated in 1.0 M Na2HPO4 at 60 °C in order to hydrolyze the DCPD into Ca10-x(HPO4x(PO4 6-x(OH2-x (CDHA and Ca8H2(PO46 .5H2O (OCP. The result is a monolithic piece which preserves the initial shape and size, but which is composed instead of CDHA, OCP, and b-TCP. During the initial stage, when the pH is slightly alkaline, the product of DCPD hydrolysis is CDHA. However, when a neutral or slightly acidic pH is reached OCP is formed. Test samples processed by this method showed complete conversion of DCPD into CDHA and OCP after 112 h of hydrolysis, and with a compressive strength of 16.2 MPa, similar to cancellous bone.

  11. Catastrophic failure of a monolithic zirconia prosthesis.

    Science.gov (United States)

    Chang, Jae-Seung; Ji, Woon; Choi, Chang-Hoon; Kim, Sunjai

    2015-02-01

    Recently, monolithic zirconia restorations have received attention as an alternative to zirconia veneered with feldspathic porcelain to eliminate chipping failures of veneer ceramics. In this clinical report, a patient with mandibular edentulism received 4 dental implants in the interforaminal area, and a screw-retained monolithic zirconia prosthesis was fabricated. The patient also received a maxillary complete removable dental prosthesis over 4 anterior roots. At the 18-month follow-up, all of the zirconia cylinders were seen to be fractured, and the contacting abutment surfaces had lost structural integrity. The damaged abutments were replaced with new abutments, and a new prosthesis was delivered with a computer-assisted design and computer-assisted manufacturing fabricated titanium framework with denture teeth and denture base resins. At the 6-month recall, the patient did not have any problems. Dental zirconia has excellent physical properties; however, care should be taken to prevent excessive stresses on the zirconia cylinders when a screw-retained zirconia restoration is planned as a definitive prosthesis.

  12. Preparation and Characterization of Temperature-responsive Porous Monoliths

    Institute of Scientific and Technical Information of China (English)

    ZHANG, Rongyue; QI, Li; XIN, Peiyong; YANG, Gengliang; CHEN, Yi

    2009-01-01

    A new temperature-responsive porous monolith has been prepared by surface-initiated activators generated by electron transfer atom transfer radical polymerization (AGET ATRP) grafting poly(N-isopropylacrylamide) (PNIPAAm) within the pores of the porous polymer monolith. The grafting copolymerization was carried out by a method based on a continuous flow-through technique without special deoxygenation procedure needed in the general ATRP. The addition of ascorbic acid could counteract the oxidation effect of oxygen diffusing into the reaction system. The resulting grafted monolith was characterized by a mercury intrusion method and the size of macropore was 3.65 μm, which was suitable for flow through the monolith for HPLC. The thermally responsive property of the grafted monolith was evaluated by HPLC using steroids with various hydrophobicities as probes. Through determination of retention factor of each steroid on the grafted monolith at different temperatures using water as mobile phase, it was found that the slope of the plot of retention factor of each steroid versus the temperature changed around the low critical solution temperature (LCST, 32 ℃) of PNIPAAm in water. It was relative to the grafted PNIPAAm temperature sensitivity that a hydrophobic and hydrophilic alternation would take place around its LCST.Based on this thermally responsive property, the grafted monolith was used as stationary phase for HPLC and to separate the steroids using water as mobile phase by changing the column temperature. As a mobile phase, water is much better than organic solvents concerning the environment.

  13. Influence of different carbon monolith preparation parameters on pesticide adsorption

    Directory of Open Access Journals (Sweden)

    Vukčević Marija

    2013-01-01

    Full Text Available The capacity of carbon monolith for pesticide removal from water, and the mechanism of pesticide interaction with carbon surface were examined. Different carbon monolith samples were obtained by varying the carbonization and activation parameters. In order to examine the role of surface oxygen groups in pesticide adsorption, carbon monolith surface was functionalized by chemical treatment in HNO3, H2O2 and KOH. The surface properties of the obtained samples were investigated by BET surface area, pore size distribution and temperature-programmed desorption. Adsorption of pesticides from aqueous solution onto activated carbon monolith samples was studied by using five pesticides belonging to different chemical groups (acetamiprid, dimethoate, nicosulfuron, carbofuran and atrazine. Presented results show that higher temperature of carbonization and the amount of activating agent allow obtaining microporous carbon monolith with higher amount of surface functional groups. Adsorption properties of the activated carbon monolith were more readily affected by the amount of the surface functional groups than by specific surface area. Results obtained by carbon monolith functionalisation showed that π-π interactions were the main force for adsorption of pesticides with aromatic structure, while acidic groups play an important role in adsorption of pesticides with no aromatic ring in the chemical structure.

  14. Aggregate and Mineral Resources - Minerals

    Data.gov (United States)

    NSGIC State | GIS Inventory — This point occurrence data set represents the current mineral and selected energy resources of Utah. The data set coordinates were derived from USGS topographic maps...

  15. Preliminary comparison of monolithic and aperture optics for XRMF

    Energy Technology Data Exchange (ETDEWEB)

    Havrilla, G.J.; Worley, C.G.

    1997-08-01

    Comparisons between standard aperture optics and a custom designed monolithic capillary x-ray optic for the Kevex Omicron are presented. The results demonstrate the feasibility of retrofitting an Omicron with a monolithic capillary. Increased flux is observed especially at lower energies which results in an increase in sensitivity and potentially an increase in spatial resolution. Alignment is a critical factor in achieving optimal performance of the monolithic capillary. Further improvements in flux output, spot size and overall sensitivity are expected with better alignment.

  16. On monolithic stability and reinforcement analysis of high arch dams

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Monolithic stability safety and reinforcement based on monolithic stability are very important for arch dam design.In this paper,the issue is addressed based on deformation reinforcement theory.In this approach,plastic complementary energy norm can be taken as safety Index for monolithic stability.According to deformation reinforcement theory,the areas where unbalanced force exists require reinforcement,and the required reinforcement forces are just the unbalanced forces with opposite direction.Results show that areas with unbalanced force mainly concentrate in dam-toes,dam-heels and faults.

  17. Hierarchically Structured Monolithic ZSM-5 through Macroporous Silica Gel Zeolitization

    Institute of Scientific and Technical Information of China (English)

    Lei Qian; Zhao Tianbo; Li Fengyan; Zong Baoning; Tong Yangchuan

    2006-01-01

    The hierarchically structured ZSM-5 monolith was prepared through transforming the skeletons of the macroporous silica gel into ZSM-5 by the steam-assisted conversion method. The morphology and monolithic shapes of macroporous silica gel were well preserved. The hierarchically structured ZSM-5 monolith exhibited the hierarchical porosity, with mesopores and macropores existing inside the macroporous silica gel, and micropores formed by the ZSM-5. The products have been characterized properly by using the XRD, SEM and N2 adsorption-desorption methods.

  18. Preparation of carbon monoliths from orange peel for NOx retention

    Directory of Open Access Journals (Sweden)

    Liliana Giraldo

    2014-12-01

    Full Text Available A series of monoliths are prepared from orange peels and chemically activated with H3PO4, KOH, ZnCl2, and water vapor without a binder. The monoliths were characterized by N2 adsorption-desorption isotherms at 77 K, Boehm titrations and XPS. Thereafter, monoliths were tested for their ability to establish NOx retention. The results show that the retention capacities of NOx were a function of the textural properties and chemistries. The carbons synthesized with ZnCl2 and KOH retained similar amounts of NOx.

  19. A decoupled monolithic projection method for natural convection problems

    Science.gov (United States)

    Pan, Xiaomin; Kim, Kyoungyoun; Lee, Changhoon; Choi, Jung-Il

    2016-06-01

    We propose an efficient monolithic numerical procedure based on a projection method for solving natural convection problems. In the present monolithic method, the buoyancy, linear diffusion, and nonlinear convection terms are implicitly advanced by applying the Crank-Nicolson scheme in time. To avoid an otherwise inevitable iterative procedure in solving the monolithic discretized system, we use a linearization of the nonlinear convection terms and approximate block lower-upper (LU) decompositions along with approximate factorization. Numerical simulations demonstrate that the proposed method is more stable and computationally efficient than other semi-implicit methods, preserving temporal second-order accuracy.

  20. Monolithically Peltier-cooled laser diodes

    Energy Technology Data Exchange (ETDEWEB)

    Hava, S.; Hunsperger, R.G.; Sequeira, H.B.

    1984-04-01

    A new method of cooling a GaAs/GaAlAs laser in an optical integrated circuit or on a discrete chip, by adding an integral thermoelectric (Peltier) cooling and heat spreading device to the laser, is presented. This cooling both reduces and stabilizes the laser junction temperature to minimize such deleterious effects as wavelength drift due to heating. A unified description of the electrical and thermal properties of a monolithic semiconductor mesa structure is given. Here it is shown that an improvement in thermal characteristics is obtained by depositing a relatively thick metallic layer, and by using this layer as a part of an active Peltier structure. Experimental results reveal a 14-percent increase in emitted power (external quantum efficiency) due to passive heat spreading and a further 8-percent if its Peltier cooler is operated. Fabrication techniques used to obtain devices exhibiting the above performance characteristics are given. 21 references.

  1. LSST primary/tertiary monolithic mirror

    Science.gov (United States)

    Sebag, J.; Gressler, W.; Liang, M.; Neill, D.; Araujo-Hauck, C.; Andrew, J.; Angeli, G.; Cho, M.; Claver, C.; Daruich, F.; Gessner, C.; Hileman, E.; Krabbendam, V.; Muller, G.; Poczulp, G.; Repp, R.; Wiecha, O.; Xin, B.; Kenagy, K.; Martin, H. M.; Tuell, M. T.; West, S. C.

    2016-08-01

    At the core of the Large Synoptic Survey Telescope (LSST) three-mirror optical design is the primary/tertiary (M1M3) mirror that combines these two large mirrors onto one monolithic substrate. The M1M3 mirror was spin cast and polished at the Steward Observatory Mirror Lab at The University of Arizona (formerly SOML, now the Richard F. Caris Mirror Lab at the University of Arizona (RFCML)). Final acceptance of the mirror occurred during the year 2015 and the mirror is now in storage while the mirror cell assembly is being fabricated. The M1M3 mirror will be tested at RFCML after integration with its mirror cell before being shipped to Chile.

  2. A monolithic thin film electrochromic window

    Energy Technology Data Exchange (ETDEWEB)

    Goldner, R.B.; Arntz, F.O.; Berera, G.; Haas, T.E.; Wong, K.K. (Tufts Univ., Medford, MA (United States). Electro-Optics Technology Center); Wei, G. (Mobil Solar Energy Corp., Billerica, MA (United States)); Yu, P.C. (PPG Industries, Inc., Monroeville, PA (United States))

    1991-01-01

    Three closely related thin film solid state ionic devices that are potentially important for applications are: electrochromic smart windows, high energy density thin film rechargeable batteries, and thin film electrochemical sensors. Each usually has at least on mixed ion/electron conductor, an electron-blocking ion conductor, and an ion-blocking electron conductor, and many of the technical issues associated with thin film solid state ionics are common to all three devices. Since the electrochromic window has the added technical requirement of electrically-controlled optical modulation, (over the solar spectrum), and since research at the authors' institution has focused primarily on the window structure, this paper will address the electrochromic window, and particularly a monolithic variable reflectivity electrochromic window, as an illustrative example of some of the challenges and opportunities that are confronting the thin film solid state ionics community. 33 refs.

  3. A monolithic thin film electrochromic window

    Energy Technology Data Exchange (ETDEWEB)

    Goldner, R.B.; Arntz, F.O.; Berera, G.; Haas, T.E.; Wong, K.K. [Tufts Univ., Medford, MA (United States). Electro-Optics Technology Center; Wei, G. [Mobil Solar Energy Corp., Billerica, MA (United States); Yu, P.C. [PPG Industries, Inc., Monroeville, PA (United States)

    1991-12-31

    Three closely related thin film solid state ionic devices that are potentially important for applications are: electrochromic smart windows, high energy density thin film rechargeable batteries, and thin film electrochemical sensors. Each usually has at least on mixed ion/electron conductor, an electron-blocking ion conductor, and an ion-blocking electron conductor, and many of the technical issues associated with thin film solid state ionics are common to all three devices. Since the electrochromic window has the added technical requirement of electrically-controlled optical modulation, (over the solar spectrum), and since research at the authors` institution has focused primarily on the window structure, this paper will address the electrochromic window, and particularly a monolithic variable reflectivity electrochromic window, as an illustrative example of some of the challenges and opportunities that are confronting the thin film solid state ionics community. 33 refs.

  4. Machining distortion prediction of aerospace monolithic components

    Institute of Scientific and Technical Information of China (English)

    Yun-bo BI; Qun-lin CHENG; Hui-yue DONG; Ying-lin KE

    2009-01-01

    To predict the distortion of aerospace monolithic components.a model is established to simulate the numerical control (NC)milling process using 3D finite element method(FEM).In this model,the cutting layer is simplified firstly.Then,the models of cutting force and cutting temperature are established to gain the cutting loads,which are applied to the mesh model of the part.Finally,a prototype of machining simulation environment is developed to simulate the milling process of a spar.Key factors influencing the distortion,such as initial residual stress,cutting loads,fixture layout,cutting sequence,and tool path are considered all together.The total distortion of the spar is predicted and an experiment is conducted to validate the numerical results.It is found that the maximum discrepancy between the simulation results and experiment values is 19.0%

  5. Solid oxide fuel cell having monolithic core

    Science.gov (United States)

    Ackerman, J. P.; Young, J. E.

    1983-10-01

    A solid oxide fuel cell is described for electrochemically combining fuel and oxidant for generating galvanic output, wherein the cell core has an array of electrolyte and interconnect walls that are substantially devoid of any composite inert materials for support. The core is monolithic, where each electrolyte wall consists of thin layers of cathode and anode materials sandwiching a thin layer of electrolyte material. The electrolyte walls are arranged and backfolded between adjacent interconnect walls operable to define a plurality of core passageways alternately arranged where the inside faces have only the anode material or only the cathode material exposed. Each layer of the electrolyte and interconnect materials 0.002 to 0.01 cm thick; and each layer of the cathode and anode materials is 0.002 to 0.05 cm thick.

  6. Silver deposition on chemically treated carbon monolith

    Directory of Open Access Journals (Sweden)

    Jovanović Zoran M.

    2009-01-01

    Full Text Available Carbon monolith was treated with HNO3, KOH and H2O2. Effects of these treatments on the surface functional groups and on the amount of silver deposited on the CM surface were studied by temperature programmed desorption (TPD and atomic absorption spectrometry (AAS. As a result of chemical treatment there was an increase in the amount of surface oxygen complexes. The increase in the amount of silver deposit is proportional to the amount of surface groups that produce CO under decomposition. However, the high amount of CO groups, decomposing above 600°C, induces the smaller Ag crystallite size. Therefore, the high temperature CO evolving oxides are, most likely, the initial centers for Ag deposition.

  7. Fumarolic minerals

    DEFF Research Database (Denmark)

    Balic Zunic, Tonci; Garavelli, Anna; Jakobsson, Sveinn Peter

    2016-01-01

    The fumarolic mineralogy of the Icelandic active volcanoes, the Tyrrhenian volcanic belt (Italy) and the Aegean active arc (Greece) is investigated, and literature data surveyed in order to define the characteristics of the European fumarolic systems. They show broad diversity of mineral...... associations, with Vesuvius and Vulcano being also among the world localities richest in mineral species. Volcanic systems, which show recession over a longer period, show fumarolic development from the hightemperature alkaline halide/sulphate, calcic sulphate or sulphidic parageneses, synchronous...... fluctuations in activity, illustrated by the example of Vulcano where the high-temperature association appears intermittently. A full survey of the mineral groups and species is given in respect to their importance and appearance in fumarolic associations....

  8. Monolithic Rare Earth Doped PTR Glass Laser Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The main goal of the project is to demonstrate the feasibility of a monolithic solid state laser on the basis of PTR glass co-doped with luminescent rare earth ions....

  9. Plant oil-based shape memory polymer using acrylic monolith

    Directory of Open Access Journals (Sweden)

    T. Tsujimoto

    2015-09-01

    Full Text Available This article deals with the synthesis of a plant oil-based material using acrylic monolith. An acrylic monolith bearing oxirane groups was prepared via simple technique that involved the dissolution of poly(glycidyl methacrylate-comethyl methacrylate (PGMA in ethanolic – aqueous solution by heating and subsequent cooling. The PGMA monolith had topologically porous structure, which was attributed to the phase separation of the polymer solution. The PGMA monolith was impregnated by epoxidized soybean oil (ESO containing thermally-latent catalyst, and the subsequent curing produced a crosslinked material with relatively good transparency. The Young’s modulus and the tensile strength of polyESO/PGMA increased compared with the ESO homopolymer. The strain at break of polyESO/PGMA was larger than that of the ESO homopolymer and crosslinked PGMA. Furthermore, polyESO/PGMA exhibited good shape memory-recovery behavior.

  10. Application of monolithic chromatographic supports in virus research.

    Science.gov (United States)

    Krajacic, Mladen; Ravnikar, Maja; Štrancar, Aleš; Gutiérrez-Aguirre, Ion

    2017-05-12

    Key properties of monolithic chromatographic supports, make them suitable for separation and/or concentration of large biomolecules, especially virus particles and viral genomes. One by one, the studies that have been completed so far, contributed to the knowledge that monolith chromatography has hardly any limitation to be applied in virus research. Viruses of different sizes, possessing icosahedral structure and symmetrical morphology, as well as rod-shaped or filamentous viruses with helical structure, even enveloped ones, all of them could be successfully managed by means of monolith chromatography. Same is true for viral genomes, primarily when being distinct from other nucleic acid forms present in a host cell. This review is exclusively focused on viruses. It describes the application of monolith chromatography to different problematics within the virus research field. The reviewed achievements offer new possibilities and trigger new aspects in virology. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Monolithic Perovskite Silicon Tandem Solar Cells with Advanced Optics

    Energy Technology Data Exchange (ETDEWEB)

    Goldschmidt, Jan C.; Bett, Alexander J.; Bivour, Martin; Blasi, Benedikt; Eisenlohr, Johannes; Kohlstadt, Markus; Lee, Seunghun; Mastroianni, Simone; Mundt, Laura; Mundus, Markus; Ndione, Paul; Reichel, Christian; Schubert, Martin; Schulze, Patricia S.; Tucher, Nico; Veit, Clemens; Veurman, Welmoed; Wienands, Karl; Winkler, Kristina; Wurfel, Uli; Glunz, Stefan W.; Hermle, Martin

    2016-11-14

    For high efficiency monolithic perovskite silicon tandem solar cells, we develop low-temperature processes for the perovskite top cell, rear-side light trapping, optimized perovskite growth, transparent contacts and adapted characterization methods.

  12. Effect of accelerated aging on translucency of monolithic zirconia

    Directory of Open Access Journals (Sweden)

    O. Abdelbary

    2016-12-01

    Conclusion: Thickness of zirconia has significant effect on translucency. Aging has significant effect on thinner sections of zirconia. More research is required on zirconia towards making the material more translucent for its potential use as esthetic monolithic restoration.

  13. Monolithic CMOS pixel detector for international linear collider vertex detection

    Indian Academy of Sciences (India)

    J E Brau; O Igonkina; N Sinew; D Strom; C Baltay; W Emmet; H Neal; D Rabinowitz

    2007-12-01

    A monolithic CMS pixel detector is under development for an ILC experiment. This chronopixel array provides a time stamp resolution of one bunch crossing, a critical feature for background suppression. The status of this effort is summarized.

  14. Performance characteristics between monolithic and microservice-based systems

    OpenAIRE

    Flygare, Robin; Holmqvist, Anthon

    2017-01-01

    A new promising technology to face the problem of scalability and availability is the microservice architecture. The problem with this architecture is that there is no significant study that clearly proves the performance differences compared to the monolithic architecture. Our thesis aims to provide a more conclusive answer of how the microservice architecture differs performance wise compared to the monolithic architecture. In this study, we conducted several experiments on a self-developed...

  15. Sol-Gel Synthesis of Non-Silica Monolithic Materials

    Directory of Open Access Journals (Sweden)

    Bartłomiej Gaweł

    2010-04-01

    Full Text Available Monolithic materials have become very popular because of various applications, especially within chromatography and catalysis. Large surface areas and multimodal porosities are great advantages for these applications. New sol-gel preparation methods utilizing phase separation or nanocasting have opened the possibility for preparing materials of other oxides than silica. In this review, we present different synthesis methods for inorganic, non-silica monolithic materials. Some examples of application of the materials are also included.

  16. Reliability Analysis and Optimal Design of Monolithic Vertical Wall Breakwaters

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Burcharth, Hans F.; Christiani, E.

    1994-01-01

    Reliability analysis and reliability-based design of monolithic vertical wall breakwaters are considered. Probabilistic models of the most important failure modes, sliding failure, failure of the foundation and overturning failure are described . Relevant design variables are identified and relia......Reliability analysis and reliability-based design of monolithic vertical wall breakwaters are considered. Probabilistic models of the most important failure modes, sliding failure, failure of the foundation and overturning failure are described . Relevant design variables are identified...

  17. Extended Leach Testing of Simulated LAW Cast Stone Monoliths

    Energy Technology Data Exchange (ETDEWEB)

    Serne, R. Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Williams, Benjamin D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jung, H. B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wang, Guohui [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-07-09

    This report describes the results from long-term laboratory leach tests performed at Pacific Northwest National Laboratory (PNNL) for Washington River Protection Solutions (WRPS) to evaluate the release of key constituents from monoliths of Cast Stone prepared with four simulated low-activity waste (LAW) liquid waste streams. Specific objectives of the Cast Stone long-term leach tests described in this report focused on four activities: 1. Extending the leaching times for selected ongoing EPA-1315 tests on monoliths made with LAW simulants beyond the conventional 63-day time period up to 609 days reported herein (with some tests continuing that will be documented later) in an effort to evaluate long-term leaching properties of Cast Stone to support future performance assessment activities. 2. Starting new EPA-1315 leach tests on archived Cast Stone monoliths made with four LAW simulants using two leachants (deionized water [DIW] and simulated Hanford Integrated Disposal Facility (IDF) Site vadose zone pore water [VZP]). 3. Evaluating the impacts of varying the iodide loading (starting iodide concentrations) in one LAW simulant (7.8 M Na Hanford Tank Waste Operations Simulator (HTWOS) Average) by manufacturing new Cast Stone monoliths and repeating the EPA-1315 leach tests using DIW and the VZP leachants. 4. Evaluating the impacts of using a non-pertechnetate form of Tc that is present in some Hanford tanks. In this activity one LAW simulant (7.8 M Na HTWOS Average) was spiked with a Tc(I)-tricarbonyl gluconate species and then solidified into Cast Stone monoliths. Cured monoliths were leached using the EPA-1315 leach protocol with DIW and VZP. The leach results for the Tc-Gluconate Cast Stone monoliths were compared to Cast Stone monoliths pertechnetate.

  18. Mechanically stable, hierarchically porous Cu3(btc)2 (HKUST-1) monoliths via direct conversion of copper(II) hydroxide-based monoliths.

    Science.gov (United States)

    Moitra, Nirmalya; Fukumoto, Shotaro; Reboul, Julien; Sumida, Kenji; Zhu, Yang; Nakanishi, Kazuki; Furukawa, Shuhei; Kitagawa, Susumu; Kanamori, Kazuyoshi

    2015-02-28

    The synthesis of highly crystalline macro-meso-microporous monolithic Cu3(btc)2 (HKUST-1; btc(3-) = benzene-1,3,5-tricarboxylate) is demonstrated by direct conversion of Cu(OH)2-based monoliths while preserving the characteristic macroporous structure. The high mechanical strength of the monoliths is promising for possible applications to continuous flow reactors.

  19. Monoliths: A Review of the Basics, Preparation Methods and Their Relevance to Oxidation

    Directory of Open Access Journals (Sweden)

    Sandeeran Govender

    2017-02-01

    Full Text Available Considerable research has been conducted on monolithic catalysts for various applications. Strategies toward coating monoliths are of equal interest and importance. In this paper, the preparation of monoliths and monolithic catalysts have been summarized. More specifically, a brief explanation for the manufacturing of ceramic and metallic monoliths has been provided. Also, different methods for coating γ-alumina, as a secondary support, are included. Techniques used to deposit metal-based species, zeolites and carbon onto monoliths are discussed. Furthermore, monoliths extruded with metal oxides, zeolites and carbon are described. The main foci are on the reasoning and understanding behind the preparation of monolithic catalysts. Ideas and concerns are also contributed to encourage better approaches when designing these catalysts. More importantly, the relevance of monolithic structures to reactions, such as the selective oxidation of alkanes, catalytic combustion for power generation and the preferential oxidation of carbon monoxide, has been described.

  20. Polymethacrylate monolithic and hybrid particle-monolithic columns for reversed-phase and hydrophilic interaction capillary liquid chromatography.

    Science.gov (United States)

    Jandera, Pavel; Urban, Jirí; Skeríková, Veronika; Langmaier, Pavel; Kubícková, Romana; Planeta, Josef

    2010-01-01

    We prepared hybrid particle-monolithic polymethacrylate columns for micro-HPLC by in situ polymerization in fused silica capillaries pre-packed with 3-5microm C(18) and aminopropyl silica bonded particles, using polymerization mixtures based on laurylmethacrylate-ethylene dimethacrylate (co)polymers for the reversed-phase (RP) mode and [2-(methacryloyloxy)ethyl]-dimethyl-(3-sulfopropyl) zwitterionic (co)polymers for the hydrophilic interaction (HILIC) mode. The hybrid particle-monolithic columns showed reduced porosity and hold-up volumes, approximately 2-2.5 times lower in comparison to the pure monolithic columns prepared in the whole volume of empty capillaries. The elution volumes of sample compounds are also generally lower in comparison to packed or pure monolithic columns. The efficiency and permeability of the hybrid columns are intermediate in between the properties of the reference pure monolithic and particle-packed columns. The chemistries of the embedded solid particles and of the interparticle monolithic moiety in the hybrid capillary columns contribute to the retention to various degrees, affecting the selectivity of separation. Some hybrid columns provided improved separations of proteins in comparison to the reference particle-packed columns in the reversed-phase mode. Zwitterionic hybrid particle-monolithic columns show dual mode retention HILIC/RP behaviour depending on the composition of the mobile phase and allow separations of polar compounds such as phenolic acids in the HILIC mode at lower concentrations of acetonitrile and, often in shorter analysis time in comparison to particle-packed and full-volume monolithic columns.

  1. Biasable, Balanced, Fundamental Submillimeter Monolithic Membrane Mixer

    Science.gov (United States)

    Siegel, Peter; Schlecht, Erich; Mehdi, Imran; Gill, John; Velebir, James; Tsang, Raymond; Dengler, Robert; Lin, Robert

    2010-01-01

    This device is a biasable, submillimeter-wave, balanced mixer fabricated using JPL s monolithic membrane process a simplified version of planar membrane technology. The primary target application is instrumentation used for analysis of atmospheric constituents, pressure, temperature, winds, and other physical and chemical properties of the atmospheres of planets and comets. Other applications include high-sensitivity gas detection and analysis. This innovation uses a balanced configuration of two diodes allowing the radio frequency (RF) signal and local oscillator (LO) inputs to be separated. This removes the need for external diplexers that are inherently narrowband, bulky, and require mechanical tuning to change frequency. Additionally, this mixer uses DC bias-ability to improve its performance and versatility. In order to solve problems relating to circuit size, the GaAs membrane process was created. As much of the circuitry as possible is fabricated on-chip, making the circuit monolithic. The remainder of the circuitry is precision-machined into a waveguide block that holds the GaAs circuit. The most critical alignments are performed using micron-scale semiconductor technology, enabling wide bandwidth and high operating frequencies. The balanced mixer gets superior performance with less than 2 mW of LO power. This can be provided by a simple two-stage multiplier chain following an amplifier at around 90 GHz. Further, the diodes are arranged so that they can be biased. Biasing pushes the diodes closer to their switching voltage, so that less LO power is required to switch the diodes on and off. In the photo, the diodes are at the right end of the circuit. The LO comes from the waveguide at the right into a reduced-height section containing the diodes. Because the diodes are in series to the LO signal, they are both turned on and off simultaneously once per LO cycle. Conversely, the RF signal is picked up from the RF waveguide by the probe at the left, and flows

  2. Mineral bioprocessing

    Energy Technology Data Exchange (ETDEWEB)

    Torma, A.E.

    1993-05-01

    In the last 25 years, the introduction of biotechnological methods in hydrometallurgy has created new opportunities and challenges for the mineral processing industry. This was especially true for the production of metal values from mining wastes and low-and-complex-grade mineral resources, which were considered economically not amenable for processing by conventional extraction methods. Using bio-assisted heap, dump and in-situ leaching technologies, copper and uranium extractions gained their first industrial applications. The precious metal industries were the next to adopt the bio-preoxidation technique in the extraction of gold from refractory sulfide-bearing ores and concentrates. A variety of other bioleaching opportunities exist for nickel, cobalt, cadmium and zinc sulfide leaching. Recently developed bioremediation methods and biosorption technologies have shown a good potential for industrial applications to remove trace heavy metal and radionuclide concentrations from contaminated soils, and mining and processing effluents.

  3. Dedicated monolithic infrared spectrometer for process monitoring

    Science.gov (United States)

    Chadha, Suneet; Kyle, William; Bolduc, Roy A.; Curtiss, Lawrence E.

    1999-12-01

    Foster-Miller has leveraged its innovations in IR fiber- optic probes and the recent development of a miniature spectrometer to build a novel IR sensor system for process applications. The developed sensor systems is a low-cost alternative to process FTIR and filter based systems. A monolithic wedge-grating optic provides the spectral dispersion with low cost thermopile point or array detectors picking off the diffracted wavelengths from the optic. The integrated optic provides spectral discrimination between 3- 12 micrometers with resolution at 8 cm-1 or better and high overall optical throughput. The device has a fixed cylindrical grating uniquely bonded to the edge of a ZnSe conditioning 'wedge'. The conditioning optic overcomes limitations of concave gratings as it accepts high angle light at the narrow end of the wedge and progressively conditions it to be near normal to the grating. On return, the diffracted wavelengths are concentrated on the discrete or array detector elements by the wedge, providing throughput comparable to that of an FTIR. The miniature spectrometer coupled to flow through liquid cells or multipass gas cells provides significant cost advantage over conventional sampling methodologies. Currently, we are investigating process applications for the petroleum and dairy markets. The sensor system eliminates the cost, complexity, reliability and bandwidth/resolution problems associated with either Fabry Perot or Michelson Interferometer based approaches for low-cost process applications.

  4. The Advanced Virgo monolithic fused silica suspension

    Energy Technology Data Exchange (ETDEWEB)

    Aisa, D.; Aisa, S.; Campeggi, C.; Colombini, M. [University of Perugia and INFN Perugia (Italy); Conte, A. [University of Roma Sapienza and INFN Roma (Italy); Farnesini, L. [University of Perugia and INFN Perugia (Italy); Majorana, E.; Mezzani, F. [University of Roma Sapienza and INFN Roma (Italy); Montani, M. [University of Urbino and INFN Firenze (Italy); Naticchioni, L.; Perciballi, M. [University of Roma Sapienza and INFN Roma (Italy); Piergiovanni, F. [University of Urbino and INFN Firenze (Italy); Piluso, A. [University of Perugia and INFN Perugia (Italy); Puppo, P., E-mail: paola.puppo@roma1.infn.it [University of Roma Sapienza and INFN Roma (Italy); Rapagnani, P. [University of Roma Sapienza and INFN Roma (Italy); Travasso, F. [University of Perugia and INFN Perugia (Italy); Vicerè, A. [University of Urbino and INFN Firenze (Italy); Vocca, H. [University of Perugia and INFN Perugia (Italy)

    2016-07-11

    The detection of gravitational waves is one of the most challenging prospects faced by experimental physicists. Suspension thermal noise is an important noise source at operating frequencies between approximately 10 and 30 Hz, and represents a limit to the sensitivity of the ground based interferometric gravitational wave detectors. Its effects can be reduced by minimizing the losses and by optimizing the geometry of the suspension fiber as well as its attachment system. In this proceeding we will describe the mirrors double stage monolithic suspension system to be used in the Advanced Virgo (AdV) detector. We also present the results of the thermal noise study, performed with the help of a finite elements model, taking into account the precise geometry of the fibers attachment systems on the suspension elements. We shall demonstrate the suitability of this suspension for installation in AdV. - Highlights: • Suspension system design for the test masses of the gravitational wave detectors. • Finite element model studies. • Suspension thermal noise studies.

  5. Monolithic supports with unique geometries and enhanced mass transfer.

    Energy Technology Data Exchange (ETDEWEB)

    Stuecker, John Nicholas; Ferrizz, Robert Matthew; Cesarano, Joseph, III; Miller, James Edward

    2004-01-01

    The catalytic combustion of natural gas has been the topic of much research over the past decade. Interest in this technology results from a desire to decrease or eliminate the emissions of harmful nitrogen oxides (NOX) from gas turbine power plants. A low-pressure drop catalyst support, such as a ceramic monolith, is ideal for this high-temperature, high-flow application. A drawback to the traditional honeycomb monoliths under these operating conditions is poor mass transfer to the catalyst surface in the straight-through channels. 'Robocasting' is a unique process developed at Sandia National Laboratories that can be used to manufacture ceramic monoliths with alternative 3-dimensional geometries, providing tortuous pathways to increase mass transfer while maintaining low pressure drops. This report details the mass transfer effects for novel 3-dimensional robocast monoliths, traditional honeycomb-type monoliths, and ceramic foams. The mass transfer limit is experimentally determined using the probe reaction of CO oxidation over a Pt / {gamma}-Al{sub 2}O{sub 3} catalyst, and the pressure drop is measured for each monolith sample. Conversion versus temperature data is analyzed quantitatively using well-known dimensionless mass transfer parameters. The results show that, relative to the honeycomb monolith support, considerable improvement in mass transfer efficiency is observed for robocast samples synthesized using an FCC-like geometry of alternating rods. Also, there is clearly a trade-off between enhanced mass transfer and increased pressure drop, which can be optimized depending on the particular demands of a given application.

  6. Advanced Gasification Mercury/Trace Metal Control with Monolith Traps

    Energy Technology Data Exchange (ETDEWEB)

    Musich, Mark; Swanson, Michael; Dunham, Grant; Stanislowski, Joshua

    2010-10-05

    Two Corning monoliths and a non-carbon-based material have been identified as potential additives for mercury capture in syngas at temperatures above 400°F and pressure of 600 psig. A new Corning monolith formulation, GR-F1-2189, described as an active sample appeared to be the best monolith tested to date. The Corning SR Liquid monolith concept continues to be a strong candidate for mercury capture. Both monolith types allowed mercury reduction to below 5-μg/m{sup 3} (~5 ppb), a current U.S. Department of Energy (DOE) goal for trace metal control. Preparation methods for formulating the SR Liquid monolith impacted the ability of the monolith to capture mercury. The Energy & Environmental Research Center (EERC)-prepared Noncarbon Sorbents 1 and 2 appeared to offer potential for sustained and significant reduction of mercury concentration in the simulated fuel gas. The Noncarbon Sorbent 1 allowed sustained mercury reduction to below 5-μg/m{sup 3} (~5 ppb). The non-carbon-based sorbent appeared to offer the potential for regeneration, that is, desorption of mercury by temperature swing (using nitrogen and steam at temperatures above where adsorption takes place). A Corning cordierite monolith treated with a Group IB metal offered limited potential as a mercury sorbent. However, a Corning carbon-based monolith containing prereduced metallic species similar to those found on the noncarbon sorbents did not exhibit significant or sustained mercury reduction. EERC sorbents prepared with Group IB and IIB selenide appeared to have some promise for mercury capture. Unfortunately, these sorbents also released Se, as was evidenced by the measurement of H2Se in the effluent gas. All sorbents tested with arsine or hydrogen selenide, including Corning monoliths and the Group IB and IIB metal-based materials, showed an ability to capture arsine or hydrogen selenide at 400°F and 600 psig. Based on current testing, the noncarbon metal-based sorbents appear to be the most

  7. ADVANCED GASIFICATION MERCURY/TRACE METAL CONTROL WITH MONOLITH TRAPS

    Energy Technology Data Exchange (ETDEWEB)

    Mark A. Musich; Michael L. Swanson; Grant E. Dunham; Joshua J. Stanislowski

    2010-07-31

    Two Corning monoliths and a non-carbon-based material have been identified as potential additives for mercury capture in syngas at temperatures above 400°F and pressure of 600 psig. A new Corning monolith formulation, GR-F1-2189, described as an active sample appeared to be the best monolith tested to date. The Corning SR Liquid monolith concept continues to be a strong candidate for mercury capture. Both monolith types allowed mercury reduction to below 5-μg/m3 (~5 ppb), a current U.S. Department of Energy (DOE) goal for trace metal control. Preparation methods for formulating the SR Liquid monolith impacted the ability of the monolith to capture mercury. The Energy & Environmental Research Center (EERC)-prepared Noncarbon Sorbents 1 and 2 appeared to offer potential for sustained and significant reduction of mercury concentration in the simulated fuel gas. The Noncarbon Sorbent 1 allowed sustained mercury reduction to below 5-μg/m3 (~5 ppb). The non-carbon-based sorbent appeared to offer the potential for regeneration, that is, desorption of mercury by temperature swing (using nitrogen and steam at temperatures above where adsorption takes place). A Corning cordierite monolith treated with a Group IB metal offered limited potential as a mercury sorbent. However, a Corning carbon-based monolith containing prereduced metallic species similar to those found on the noncarbon sorbents did not exhibit significant or sustained mercury reduction. EERC sorbents prepared with Group IB and IIB selenide appeared to have some promise for mercury capture. Unfortunately, these sorbents also released Se, as was evidenced by the measurement of H2Se in the effluent gas. All sorbents tested with arsine or hydrogen selenide, including Corning monoliths and the Group IB and IIB metal-based materials, showed an ability to capture arsine or hydrogen selenide at 400°F and 600 psig. Based on current testing, the noncarbon metal-based sorbents appear to be the most effective arsine

  8. New Graphene Form of Nanoporous Monolith for Excellent Energy Storage.

    Science.gov (United States)

    Bi, Hui; Lin, Tianquan; Xu, Feng; Tang, Yufeng; Liu, Zhanqiang; Huang, Fuqiang

    2016-01-13

    Extraordinary tubular graphene cellular material of a tetrahedrally connected covalent structure was very recently discovered as a new supermaterial with ultralight, ultrastiff, superelastic, and excellent conductive characteristics, but no high specific surface area will keep it from any next-generation energy storage applications. Herein, we prepare another new graphene monolith of mesoporous graphene-filled tubes instead of hollow tubes in the reported cellular structure. This graphene nanoporous monolith is also composed of covalently bonded carbon network possessing high specific surface area of ∼1590 m(2) g(-1) and electrical conductivity of ∼32 S cm(-1), superior to graphene aerogels and porous graphene forms self-assembled by graphene oxide. This 3D graphene monolith can support over 10 000 times its own weight, significantly superior to CNT and graphene cellular materials with a similar density. Furthermore, pseudocapacitance-active functional groups are introduced into the new nanoporous graphene monolith as an electrode material in electrochemical capacitors. Surprisingly, the electrode of 3D mesoporous graphene has a specific capacitance of 303 F g(-1) and maintains over 98% retention after 10 000 cycles, belonging to the list for the best carbon-based active materials. The macroscopic mesoporous graphene monolith suggests the great potential as an electrode for supercapacitors in energy storage areas.

  9. Recent advances in polymer monoliths for ion-exchange chromatography.

    Science.gov (United States)

    Nordborg, Anna; Hilder, Emily F

    2009-05-01

    The use of polymeric materials in ion-exchange chromatography applications is advantageous because of their typically high mechanical stability and tolerance of a wide range of pH conditions. The possibility of using polymeric monoliths in ion-exchange chromatography is therefore obvious and many of the same strategies developed for polymeric particles have been adapted for use with polymeric monoliths. In this review different strategies for the synthesis of polymeric monoliths with ion-exchange functionality are discussed. The incorporation of ion-exchange functionality by co-polymerization is included, as also are different post-polymerization alterations to the monolith surface such as grafting. The formulations and strategies presented include materials intended for use in analytical separations in ion-exchange chromatography, sample pre-treatment or enrichment applications, and materials for capillary electrochromatography. Finally, examples of the use of polymeric monoliths in ion-exchange chromatography applications are included with examples published in the years 2003 to 2008.

  10. HPLC analysis of synthetic polymers on short monolithic columns.

    Science.gov (United States)

    Maksimova, Elena; Vlakh, Evgenia; Sinitsyna, Ekaterina; Tennikova, Tatiana

    2013-12-01

    Ultrashort monolithic columns (disks) were thoroughly studied as efficient stationary phases for precipitation-dissolution chromatography of synthetic polymers. Gradient elution mode was applied in all chromatographic runs. The mixtures of different flexible chain homopolymers, such as polystyrenes, poly(methyl methacrylates), and poly(tert-butylmethacrylates) were separated according to their molecular weights on both commercial poly(styrene-co-divinylbenzene) disks (12 id × 3 mm and 5 × 5 mm) and lab-made monolithic columns (4.6 id × 50 mm) filled with supports of different hydrophobicity. The experimental conditions were optimized to reach fast and highly efficient separation. It was observed that, similar to the separation of monoliths of other classes of (macro)molecules (proteins, DNA, oligonucleotides), the length of column did not affect the peak resolution. A comparison of the retention properties of the poly(styrene-co-divinylbenzene) disk-shaped monoliths with those based on poly(lauryl methacrylate-co-ethylene dimethacrylate), poly(butyl methacrylate-co-ethylene dimethacrylate), and poly(glycidyl methacrylate-co-ethylene dimethacrylate) supports demonstrated the obvious effect of surface chemistry on the resolution factor. Additionally, the results of the discussed chromatographic mode on the fast determination of the molecular weights of homopolymers used in this study were compared to those established by SEC on columns packed with sorbent beads of a similar nature to the monoliths. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Edge chipping and flexural resistance of monolithic ceramics☆

    Science.gov (United States)

    Zhang, Yu; Lee, James J.-W.; Srikanth, Ramanathan; Lawn, Brian R.

    2014-01-01

    Objective Test the hypothesis that monolithic ceramics can be developed with combined esthetics and superior fracture resistance to circumvent processing and performance drawbacks of traditional all-ceramic crowns and fixed-dental-prostheses consisting of a hard and strong core with an esthetic porcelain veneer. Specifically, to demonstrate that monolithic prostheses can be produced with a much reduced susceptibility to fracture. Methods Protocols were applied for quantifying resistance to chipping as well as resistance to flexural failure in two classes of dental ceramic, microstructurally-modified zirconias and lithium disilicate glass–ceramics. A sharp indenter was used to induce chips near the edges of flat-layer specimens, and the results compared with predictions from a critical load equation. The critical loads required to produce cementation surface failure in monolithic specimens bonded to dentin were computed from established flexural strength relations and the predictions validated with experimental data. Results Monolithic zirconias have superior chipping and flexural fracture resistance relative to their veneered counterparts. While they have superior esthetics, glass–ceramics exhibit lower strength but higher chip fracture resistance relative to porcelain-veneered zirconias. Significance The study suggests a promising future for new and improved monolithic ceramic restorations, with combined durability and acceptable esthetics. PMID:24139756

  12. Hydrothermal minerals

    Digital Repository Service at National Institute of Oceanography (India)

    Nath, B.N.

    -floor hydrothermal processes involving free circulation of seawater through ocean crust as convection. Heat flow, seafloor fracturing, permeability and fluid composition are the parameters governing the type and extent of mineralization. The chimney like... stream_size 23365 stream_content_type text/plain stream_name Refresher_Course_Mar_Geol_Geophys_2007_Lecture_Notes_78.pdf.txt stream_source_info Refresher_Course_Mar_Geol_Geophys_2007_Lecture_Notes_78.pdf.txt Content-Encoding UTF-8...

  13. Radionuclide and contaminant immobilization in the fluidized bed steam reforming waste products

    Energy Technology Data Exchange (ETDEWEB)

    Neeway, James J.; Qafoku, Nikolla; Westsik, Joseph H.; Brown, Christopher F.; Jantzen, Carol; Pierce, Eric M.

    2012-05-01

    The goal of this chapter is to introduce the reader to the Fluidized Bed Steam Reforming (FBSR) process and resulting waste form. The first section of the chapter gives an overview of the potential need for FBSR processing in nuclear waste remediation followed by an overview of the engineering involved in the process itself. This is followed by a description of waste form production at a chemical level followed by a section describing different process streams that have undergone the FBSR process. The third section describes the resulting mineral product in terms of phases that are present and the ability of the waste form to encapsulate hazardous and radioactive wastes from several sources. Following this description is a presentation of the physical properties of the granular and monolith waste form product including and contaminant release mechanisms. The last section gives a brief summary of this chapter and includes a section on the strengths associated with this waste form and the needs for additional data and remaining questions yet to be answered. The reader is directed elsewhere for more information on other waste forms such as Cast Stone (Lockrem, 2005), Ceramicrete (Singh et al., 1997, Wagh et al., 1999) and geopolymers (Kyritsis et al., 2009; Russell et al., 2006).

  14. Monolithic View of Galaxy Formation and Evolution

    Directory of Open Access Journals (Sweden)

    Cesare Chiosi

    2014-07-01

    Full Text Available We review and critically discuss the current understanding of galaxy formation and evolution limited to Early Type Galaxies (ETGs as inferred from the observational data and briefly contrast the hierarchical and quasi-monolithic paradigms of formation and evolution. Since in Cold Dark Matter (CDM cosmogony small scale structures typically collapse early and form low-mass haloes that subsequently can merge to assembly larger haloes, galaxies formed in the gravitational potential well of a halo are also expected to merge thus assembling their mass hierarchically. Mergers should occur all over the Hubble time and large mass galaxies should be in place only recently. However, recent observations of high redshift galaxies tell a different story: massive ETGs are already in place at high redshift. To this aim, we propose here a revision of the quasi-monolithic scenario as an alternative to the hierarchical one, in which mass assembling should occur in early stages of a galaxy lifetime and present recent models of ETGs made of Dark and Baryonic Matter in a Λ-CDM Universe that obey the latter scheme. The galaxies are followed from the detachment from the linear regime and Hubble flow at z ≥ 20 down to the stage of nearly complete assembly of the stellar content (z ∼ 2 − 1 and beyond.  It is found that the total mass (Mh = MDM + MBM and/or initial over-density of the proto-galaxy drive the subsequent star formation histories (SFH. Massive galaxies (Mh ~ _1012M⊙ experience a single, intense burst of star formation (with rates ≥ 103M⊙/yr at early epochs, consistently with observations, with a weak dependence on the initial over-density; intermediate mass haloes (Mh~_ 1010 − 1011M⊙ have star formation histories that strongly depend on their initial over-density; finally, low mass haloes (Mh ~_ 109M⊙ always have erratic, burst-like star forming histories. The present-day properties (morphology, structure, chemistry and photometry of the

  15. Monolithic Solid Oxide Fuel Cell development

    Science.gov (United States)

    Myles, K. M.; McPheeters, C. C.

    1989-12-01

    The Monolithic Solid Oxide Fuel Cell (MSOFC) is an oxide-ceramic structure in which appropriate electronic and ionic conductors are fabricated in a honeycomb shape similar to a block of corrugated paperboard. These electronic and ionic conductors are arranged to provide short conduction paths to minimize resistive losses. The power density achievable with the MSOFC is expected to be about 8 kW/kg or 4 kW/L, at fuel efficienceis over 50 percent, because of small cell size and low resistive losses in the materials. The MSOFC operates in the range of 700 to 1000 C, at which temperatures rapid reform of hydrocarbon fuels is expected within the nickel-YSZ fuel channels. Tape casting and hot roll calendering are used to fabricate the MSOFC structure. The performance of the MSOFC has improved significantly during the course of development. The limitation of this system, based on materials resistance alone without interfacial resistances, is 0.093 ohm-sq cm area-specific resistance (ASR). The current typical performance of MSOFC single cells is characterized by ASRs of about 0.4 to 0.5 ohm-sq cm. With further development the ASR is expected to be reduced below 0.2 ohm-sq cm, which will result in power levels greater than 1.4 W/sq cm. The feasibility of the MSOFC concept was proven, and the performance was dramatically improved. The differences in thermal expansion coefficients and firing shrinkages among the fuel cell materials were minimized. As a result of good matching of these properties, the MSOFC structure was successfully fabricated with few defects, and the system shows excellent promise for development into a practical power source.

  16. Monolithic series-connected gallium arsenide converter development

    Energy Technology Data Exchange (ETDEWEB)

    Spitzer, M.B.; McClelland, R.W.; Dingle, B.D.; Dingle, J.E.; Hill, D.S. (Kopin Corp., Taunton, MA (United States)); Rose, B.H. (Sandia National Labs., Albuquerque, NM (United States))

    1991-01-01

    We report the development of monolithic GaAs photovoltaic devices intended to convert light generated by a laser or other bright source to electricity. The converters described here can provide higher operating voltage than is possible using a single-junction converter, owing to use of a monolithic circuit that forms a planar series-connected string of single-junction sub-cells. This planar monolithic circuit is arranged to deliver the desired voltage and current during operation at the maximum power point. The paper describes two-, six-, and twelve-junction converters intended for illumination by a laser diode with a wavelength of 0.8 {mu}m. Design and characterization data are presented for optical power in the range of 100 mW to 1 W. The best conversion efficiency exceeds 50%. 9 refs., 4 figs., 2 tabs.

  17. Design of Monolithic Integrator for Strain-to-Frequency Converter

    Directory of Open Access Journals (Sweden)

    Tuan Mohd. Khairi Tuan Mat

    2012-01-01

    Full Text Available Strain-to-Frequency converter (SFC is a one of the analog conditioner tools that converts any strain signal to the frequency signal. The basic concept of SFC is by detecting any changing of strains, then converting the strain to the voltage signal and converting the voltage signal to the frequency signal. This tool consists of 3 main  components which are strain gauge, differential integrator and comparator. This paper presents the designing and analysis of monolithic integrator that to be used in the Strain-toFrequency converter. The primary goal is to design and simulate the performance of monolithic integrator for SFC using GATEWAY Silvaco Electronic Design Automation (S EDA tools and EXPERT software. The performances of SFC using the designed monolithic integrator are also investigated.

  18. Molecularly imprinted macroporous monolithic materials for protein recognition

    Institute of Scientific and Technical Information of China (English)

    Qi Liang Deng; Yan Li Li; Li Hua Zhang; Yu Kui Zhang

    2011-01-01

    Synthetic materials that can specifically recognize proteins will find wide application in many fields. In this report, bovine serum albumin was chosen as the template protein. Acrylamide and N, N'-methylenebisacrylamide were employed as the functional and cross-linker monomers, respectively. Molecularly imprinted macroporous monolithic materials that can preferentially bind the template protein in an aqueous environment were prepared by combination of molecular imprinting technique and freezing/thawing preparation method. The resulted imprinted macroporous monolithic columns were evaluated by utilizing as stationary phase in high performance liquid chromatography and solid-phase extraction materials. The experimental results indicated that the imprinted macroporous monolithic column exhibited good recognition for template protein, as compared with the control protein (hemoglobin), whereas the non-imprinted polymer (prepared under the same conditions except without addition template protein) had no selective properties.

  19. A Possible Astronomically Aligned Monolith at Gardom's Edge

    Science.gov (United States)

    Brown, Daniel; Alder, Andy; Bemand, Elizabeth

    2015-05-01

    A unique triangular shaped monolith located within the Peak District National Park at Gardom's Edge could be intentionally astronomically aligned. It is set within a landscape rich in late Neolithic and Bronze Age remains. We show that the stone is most likely in its original orientation owing to its clear signs of erosion and associated to the time period of the late Neolithic. It is tilted towards south and its north side slopes at an angle equal to the maximum altitude of the Sun at mid-summer. This alignment emphasizes the changing declinations of the Sun during the seasons as well as giving an indication of mid-summers day. This functionality is achieved by an impressive display of light and shadow on the north facing side of the monolith. Together with other monuments in the close vicinity the monolith would have represented an ideal marker or social arena for seasonal gatherings for the otherwise dispersed small communities.

  20. Preliminary shielding analysis for the CSNS target station monolith

    Institute of Scientific and Technical Information of China (English)

    张斌; 陈义学; 杨寿海; 吴军; 殷雯; 梁天骄; 贾学军

    2010-01-01

    The construction of the China Spallation Neutron Source (CSNS) has been initiated at Dongguan,Guangdong,China.In spallation neutron sources the target station monolith is contaminated by a large number of fast neutrons whose energies can be as large as those of the protons of the proton beam directed towards the tungsten target.A detailed radiation transport analysis of the target station monolith is important for the construction of the CSNS.The analysis is performed using the coupled Monte Carlo and multi-dimensional discrete ordinates method.Successful elimination of the primary ray effects via the two-dimensional uncollided flux and first collision source methodology is also illustrated.The dose at the edge of the monolith is calculated.The results demonstrate that the doses received by the hall staff members are below the required standard limit.

  1. Monolithic fuel cell based power source for burst power generation

    Science.gov (United States)

    Fee, D. C.; Blackburn, P. E.; Busch, D. E.; Dees, D. W.; Dusek, J.; Easler, T. E.; Ellingson, W. A.; Flandermeyer, B. K.; Fousek, R. J.; Heiberger, J. J.

    A unique fuel cell coupled with a low power nuclear reactor presents an attractive approach for SDI burst power requirements. The monolithic fuel cell looks attractive for space applications and represents a quantum jump in fuel cell technology. Such a breakthrough in design is the enabling technology for lightweight, low volume power sources for space based pulse power systems. The monolith is unique among fuel cells in being an all solid state device. The capability for miniaturization, inherent in solid state devices, gives the low volume required for space missions. In addition, the solid oxide fuel cell technology employed in the monolith has high temperature reject heat and can be operated in either closed or open cycles. Both these features are attractive for integration into a burst power system.

  2. A Possible Astronomically Aligned Monolith at Gardom's Edge

    CERN Document Server

    Brown, D; Bemand, E

    2012-01-01

    A unique triangular shaped monolith located within the Peak District National Park at Gardom's Edge could be intentionally astronomically aligned. It is set within a landscape rich in late Neolithic and Bronze Age remains. We show that the stone is most likely in its original orientation owing to its clear signs of erosion and associated to the time period of the late Neolithic. It is tilted towards South and its North side slopes at an angle equal to the maximum altitude of the Sun at mid-summer. This alignment emphasizes the changing declinations of the Sun during the seasons as well as giving an indication of mid-summers day. This functionality is achieved by an impressive display of light and shadow on the North-facing side of the Monolith. Together with other monuments in the close vicinity the monolith would have represented an ideal marker or social arena for seasonal gatherings for the else dispersed small communities.

  3. MONOLITHIC FUEL FABRICATION PROCESS DEVELOPMENT AT THE IDAHO NATIONAL LABORATORY_

    Energy Technology Data Exchange (ETDEWEB)

    G. A. Moore; F. J. Rice; N. E. Woolstenhulme; J-F. Jue; B. H. Park; S. E. Steffler; N. P. Hallinan; M. D. Chapple; M. C. Marshall; B. L. Mackowiak; C. R. Clark; B. H. Rabin

    2009-11-01

    Full-size/prototypic U10Mo monolithic fuel-foils and aluminum clad fuel plates are being developed at the Idaho National Laboratory’s (INL) Materials and Fuels Complex (MFC). These efforts are focused on realizing Low Enriched Uranium (LEU) high density monolithic fuel plates for use in High Performance Research and Test Reactors. The U10Mo fuel foils under development afford a fuel meat density of ~16 gU/cc and thus have the potential to facilitate LEU conversions without any significant reactor-performance penalty. An overview is provided of the ongoing monolithic UMo fuel development effort, including application of a zirconium barrier layer on fuel foils, fabrication scale-up efforts, and development of complex/graded fuel foils. Fuel plate clad bonding processes to be discussed include: Hot Isostatic Pressing (HIP) and Friction Bonding (FB).

  4. Preparation of poly(γ-glutamic acid)/hydroxyapatite monolith via biomineralization for bone tissue engineering.

    Science.gov (United States)

    Park, Sung-Bin; Hasegawa, Urara; van der Vlies, André J; Sung, Moon-Hee; Uyama, Hiroshi

    2014-01-01

    A hybrid monolith of poly(γ-glutamic acid) and hydroxyapatite (PGA/HAp monolith) was prepared via biomineralization and used as a macroporous cell scaffold in bone tissue engineering. The PGA monolith having a bimodal pore size distribution was used as a substrate to induce biomineralization. The PGA/HAp monolith was obtained by immersing the PGA monolith in simulated body fluid. Pretreatment with CaCl2 enhanced the apatite-forming ability of the PGA monolith. Murine osteoblastic MC3T3-E1 cells efficiently attached and proliferated on the PGA/HAp monolith. MTT assay showed that both the PGA and PGA/HAp monolith did not have apparent cytotoxicity. Moreover, the PGA and PGA/HAp monoliths adsorbed bone morphogenetic protein-2 (BMP-2) by electrostatic interaction which was slowly released in the medium during cell culture. The PGA/HAp monolith enhanced BMP-2 induced alkaline phosphatase activity compared to the PGA monolith and a polystyrene culture plate. Thus, these PGA/HAp monoliths may have potential in bone tissue engineering.

  5. Numerical Simulation of Fluid Dynamics in a Monolithic Column

    Directory of Open Access Journals (Sweden)

    Kazuhiro Yamamoto

    2017-01-01

    Full Text Available As for the measurement of polycyclic aromatic hydrocarbons (PAHs, ultra-performance liquid chromatography (UPLC is used for PAH identification and densitometry. However, when a solvent containing a substance to be identified passes through a column of UPLC, a dedicated high-pressure-proof device is required. Recently, a liquid chromatography instrument using a monolithic column technology has been proposed to reduce the pressure of UPLC. The present study tested five types of monolithic columns produced in experiments. To simulate the flow field, the lattice Boltzmann method (LBM was used. The velocity profile was discussed to decrease the pressure drop in the ultra-performance liquid chromatography (UPLC system.

  6. A Monolithic Oxide-Based Transversal Thermoelectric Energy Harvester

    Science.gov (United States)

    Teichert, S.; Bochmann, A.; Reimann, T.; Schulz, T.; Dreßler, C.; Udich, S.; Töpfer, J.

    2016-03-01

    We report the fabrication and properties of a monolithic transversal thermoelectric energy harvester based on the combination of a thermoelectric oxide and a metal. The fabrication of the device is done with a ceramic multilayer technology using printing and co-firing processes. Five transversal devices were combined to a meander-like thermoelectric generator. Electrical measurements and finite element calculations were performed to characterize the resulting thermoelectric generator. A maximum experimental electrical power output of 30.2 mW at a temperature difference of {Δ }T = 208 K was found. The prepared monolithic thermoelectric generator provides at {Δ }T = 35 K sufficient energy to drive a simple electronic sensor application.

  7. Monolithic Michelson Interferometer as ultra stable wavelength reference

    Science.gov (United States)

    Wan, Xiaoke; Ge, Jian

    2010-07-01

    Ultra-stable Monolithic Michelson interferometer can be an ideal reference for highprecision applications such as RV measurement in planet searching and orbit study. The advantages include wide wavelength range, simple sinusoidal spectral format, and high optical efficiency. In this paper, we report that a monolithic Michelson interferometers has been in-house developed with minimized thermal sensitivity with compensation tuning. With a scanning white light interferometer, the thermal sensitivity is measured ~ 6x10-7/°C at 550 nm and it decreases to zero near 1000 nm. We expect the wideband wavelength reference source to be stabilized better than 0.3 m/s for RV experiments

  8. Synthesis of ZSM-5 Monoliths with Hierarchical Porosity

    Institute of Scientific and Technical Information of China (English)

    Tong Yangchuan; Zhao Tianbo; Li Fengyan; Zong Baoning; Wang Yue

    2006-01-01

    A new route to synthesize ZSM-5 monoliths with hierarchical pore structure has been referred to in this stud y. The successful incorporation of the macropores and mesopores within the ZSM-5 structure was achieved through transforming the skeleton of the macroporous silica gel into zeolite ZSM-5 using carbon materials as the transitional template. The ZSM-5 crystal covered part of the macroporous material, and provided micropores to the macroporous silica gel. The structure of carbon monolith was studied after dissolving the silica contained in the carbon/silica composite.

  9. Lectin-carbohydrate interactions on nanoporous gold monoliths.

    Science.gov (United States)

    Tan, Yih Horng; Fujikawa, Kohki; Pornsuriyasak, Papapida; Alla, Allan J; Ganesh, N Vijaya; Demchenko, Alexei V; Stine, Keith J

    2013-07-01

    Monoliths of nanoporous gold (np-Au) were modified with self-assembled monolayers of octadecanethiol (C18-SH), 8-mercaptooctyl α-D-mannopyranoside (αMan-C8-SH), and 8-mercapto-3,6-dioxaoctanol (HO-PEG2-SH), and the loading was assessed using thermogravimetric analysis (TGA). Modification with mixed SAMs containing αMan-C8-SH (at a 0.20 mole fraction in the SAM forming solution) with either octanethiol or HO-PEG2-SH was also investigated. The np-Au monoliths modified with αMan-C8-SH bind the lectin Concanavalin A (Con A), and the additional mass due to bound protein was assessed using TGA analysis. A comparison of TGA traces measured before and after exposure of HO-PEG2-SH modified np-Au to Con A showed that the non-specific binding of Con A was minimal. In contrast, np-Au modified with octanethiol showed a significant mass loss due to non-specifically adsorbed Con A. A significant mass loss was also attributed to binding of Con A to bare np-Au monoliths. TGA revealed a mass loss due to the binding of Con A to np-Au monoliths modified with pure αMan-C8-SH. The use of mass losses determined by TGA to compare the binding of Con A to np-Au monoliths modified by mixed SAMs of αMan-C8-SH and either octanethiol or HO-PEG2-SH revealed that binding to mixed SAM modified surfaces is specific for the mixed SAMs with HO-PEG2-SH but shows a significant contribution from non-specific adsorption for the mixed SAMs with octanethiol. Minimal adsorption of immunoglobulin G (IgG) and peanut agglutinin (PNA) towards the mannoside modified np-Au monoliths was demonstrated. A greater mass loss was found for Con A bound onto the monolith than for either IgG or PNA, signifying that the mannose presenting SAMs in np-Au retain selectivity for Con A. TGA data also provide evidence that Con A bound to the αMan-C8-SH modified np-Au can be eluted by flowing a solution of methyl α-D-mannopyranoside through the structure. The presence of Con A proteins on the modified np-Au surface was

  10. Paladin Enterprises: Monolithic particle physics models global climate.

    CERN Multimedia

    2002-01-01

    Paladin Enterprises presents a monolithic particle model of the universe which will be used by them to build an economical fusion energy system. The model is an extension of the work done by James Clerk Maxwell. Essentially, gravity is unified with electro-magnetic forces and shown to be a product of a closed loop current system, i.e. a particle - monolithic or sub atomic. This discovery explains rapid global climate changes which are evident in the geological record and also provides an explanation for recent changes in the global climate.

  11. Polyurea-Based Aerogel Monoliths and Composites

    Science.gov (United States)

    Lee, Je Kyun

    2012-01-01

    aerogel insulation material was developed that will provide superior thermal insulation and inherent radiation protection for government and commercial applications. The rubbery polyureabased aerogel exhibits little dustiness, good flexibility and toughness, and durability typical of the parent polyurea polymer, yet with the low density and superior insulation properties associated with aerogels. The thermal conductivity values of polyurea-based aerogels at lower temperature under vacuum pressures are very low and better than that of silica aerogels. Flexible, rubbery polyurea-based aerogels are able to overcome the weak and brittle nature of conventional inorganic and organic aerogels, including polyisocyanurate aerogels, which are generally prepared with the one similar component to polyurethane rubber aerogels. Additionally, with higher content of hydrogen in their structures, the polyurea rubber-based aerogels will also provide inherently better radiation protection than those of inorganic and carbon aerogels. The aerogel materials also demonstrate good hydrophobicity due to their hydrocarbon molecular structure. There are several strategies to overcoming the drawbacks associated with the weakness and brittleness of silica aerogels. Development of the flexible fiber-reinforced silica aerogel composite blanket has proven to be one promising approach, providing a conveniently fielded form factor that is relatively robust in industrial environments compared to silica aerogel monoliths. However, the flexible, silica aerogel composites still have a brittle, dusty character that may be undesirable, or even intolerable, in certain application environments. Although the cross - linked organic aerogels, such as resorcinol- formaldehyde (RF), polyisocyanurate, and cellulose aerogels, show very high impact strength, they are also very brittle with little elongation (i.e., less rubbery). Also, silica and carbon aerogels are less efficient radiation shielding materials due

  12. Constitutive Theory Developed for Monolithic Ceramic Materials

    Science.gov (United States)

    Janosik, Lesley A.

    1998-01-01

    with these service conditions by developing a multiaxial viscoplastic constitutive model that accounts for time-dependent hereditary material deformation (such as creep and stress relaxation) in monolithic structural ceramics. Using continuum principles of engineering mechanics, we derived the complete viscoplastic theory from a scalar dissipative potential function.

  13. Chromatographic comparison of bupivacaine imprinted polymers prepared in crushed monolith, microsphere, silica-based composite and capillary monolith formats.

    Science.gov (United States)

    Oxelbark, Joakim; Legido-Quigley, Cristina; Aureliano, Carla S A; Titirici, Maria-Magdalena; Schillinger, Eric; Sellergren, Börje; Courtois, Julien; Irgum, Knut; Dambies, Laurent; Cormack, Peter A G; Sherrington, David C; De Lorenzi, Ersilia

    2007-08-10

    A comprehensive comparison of five chromatographic stationary phases based on molecularly imprinted polymers is presented. Efficiency, imprinting factors, water compatibility and batch-to-batch reproducibility are discussed for crushed monolith, microspheres, two silica-based composites and capillary monoliths, all imprinted with the local anaesthetic bupivacaine. Synthesis protocol and chromatographic test conditions have been kept fixed within certain limits, in order to provide further insight into the strengths and weaknesses of the different formats. Excluding microparticles, all formats give satisfactory performance, especially in aqueous mobile phases. An assessment of batch-to-batch reproducibility in different mobile phases adds further value to this comparison study.

  14. A radiation hard bipolar monolithic front-end readout

    CERN Document Server

    Baschirotto, A; Cappelluti, I; Castello, R; Cermesoni, M; Gola, A; Pessina, G; Pistolesi, E; Rancoita, P G; Seidman, A

    1999-01-01

    A fast bipolar monolithic charge sensitive preamplifier (CSP), implemented in the monolithic 2 mu m BiCMOS technology (called HF2CMOS) was designed and built in a quad monolithic chip. Studies of radiation effects in the CSP $9 performance, from non-irradiated and up to neutron irradiation of 5.3*10/sup 14/ n/cm/sup 2/, have confirmed that the use of bipolar npn transistors is suitable for the radiation level of the future LHC collider environment. The CSP $9 presents a new circuit solution for obtaining adequate slew rate performances which results in an integral linearity better than 0.8554330n 5 V at 20 ns of shaping time, regardless of the bias current selected for the CSP. This way $9 the bias current of the CSP can be set for optimizing the power dissipation with respect to series and parallel noise, especially useful when the CSP is put in a radiation environment. A prototype test with a novel monolithic 20 ns $9 time constant RC-CR shaper, capable to sum up four inputs has been also realized, featurin...

  15. Carbon monolith: preparation, characterization and application as microextraction fiber.

    Science.gov (United States)

    Shi, Zhi-Guo; Chen, Fei; Xing, Jun; Feng, Yu-Qi

    2009-07-10

    A carbon monolith was synthesized via a polymerization-carbonization method, styrene and divinylbenzene being adopted as precursors and dodecanol as a porogen during polymerization. The resultant monolith had bimodal porous substructure, narrowly distributed nano skeleton pores and uniform textural pores or throughpores. The carbon monolith was directly used as an extracting fiber, taking place of the coated silica fibers in commercially available solid-phase microextraction device, for the extraction of phenols followed by gas chromatography-mass spectrometry. Under the studied conditions, the calibration curves were linear from 0.5 to 50 ng mL(-1) for phenol, o-nitrophenol, 2,4-dichlorophenol and p-chlorophenol. The limits of detection were between 0.04 and 0.43 ng mL(-1). The recoveries of the phenols spiked in real water samples at 10 ng mL(-1) were between 85% and 98% with the relative standard deviations below 10%. Compared with the commercial coated ones (e.g. PDMS, CW/DVB and DVB/CAR/PDMS), the carbon monolith-based fiber had advantages of faster extraction equilibrium and higher extraction capacity due to the superior pore connectivity and pore openness resulting from its bimodal porous substructure.

  16. Shear bond strength of indirect composite material to monolithic zirconia

    Science.gov (United States)

    2016-01-01

    PURPOSE This study aimed to evaluate the effect of surface treatments on bond strength of indirect composite material (Tescera Indirect Composite System) to monolithic zirconia (inCoris TZI). MATERIALS AND METHODS Partially stabilized monolithic zirconia blocks were cut into with 2.0 mm thickness. Sintered zirconia specimens were divided into different surface treatment groups: no treatment (control), sandblasting, glaze layer & hydrofluoric acid application, and sandblasting + glaze layer & hydrofluoric acid application. The indirect composite material was applied to the surface of the monolithic zirconia specimens. Shear bond strength value of each specimen was evaluated after thermocycling. The fractured surface of each specimen was examined with a stereomicroscope and a scanning electron microscope to assess the failure types. The data were analyzed using one-way analysis of variance (ANOVA) and Tukey LSD tests (α=.05). RESULTS Bond strength was significantly lower in untreated specimens than in sandblasted specimens (P<.05). No difference between the glaze layer and hydrofluoric acid application treated groups were observed. However, bond strength for these groups were significantly higher as compared with the other two groups (P<.05). CONCLUSION Combined use of glaze layer & hydrofluoric acid application and silanization are reliable for strong and durable bonding between indirect composite material and monolithic zirconia. PMID:27555895

  17. Cyclodextrin-Functionalized Monolithic Capillary Columns: Preparation and Chiral Applications.

    Science.gov (United States)

    Adly, Frady G; Antwi, Nana Yaa; Ghanem, Ashraf

    2016-02-01

    In this review, the recently reported approaches for the preparation of cyclodextrin-functionalized capillary monolithic columns are highlighted, with few applications in chiral separations using capillary liquid chromatography (CLC) and capillary electrochromatography (CEC). Chirality 28:97-109, 2016. © 2015 Wiley Periodicals, Inc.

  18. Monolithic natural gas storage delivery system based on sorbents

    Energy Technology Data Exchange (ETDEWEB)

    Hornbostel, Marc; Krishnan, Gopala N.; Sanjurjo, Angel

    2016-09-27

    The invention provides methods for producing a strong, light, sorbent-based storage/dispenser system for gases and fuels. The system comprises a porous monolithic material with an adherent strong impervious skin that is capable of storing a gas under pressure in a safe and usable manner.

  19. Monolithic natural gas storage delivery system based on sorbents

    Energy Technology Data Exchange (ETDEWEB)

    Hornbostel, Marc; Krishnan, Gopala N.; Sanjurjo, Angel

    2016-09-27

    The invention provides methods for producing a strong, light, sorbent-based storage/dispenser system for gases and fuels. The system comprises a porous monolithic material with an adherent strong impervious skin that is capable of storing a gas under pressure in a safe and usable manner.

  20. Multiple Quantum Well (MQW) Devices For Monolithic Integrated Optoelectronics

    Science.gov (United States)

    Wood, Thomas H.

    1988-05-01

    Semiconductor MQWs represent a new technology for opto-electronics. These MQWs have an electroabsorption effect approximately 50 times larger than conventional semiconductors. They are compatible with existing source and detector material systems and produce devices that are compact and high speed, which makes them useful for monolithic integrated optoelectronic devices.

  1. Morphosynthesis of cubic silver cages on monolithic activated carbon.

    Science.gov (United States)

    Wang, Fei; Zhao, Hong; Lai, Yijian; Liu, Siyu; Zhao, Binyuan; Ning, Yuesheng; Hu, Xiaobin

    2013-11-14

    Cubic silver cages were prepared on monolithic activated carbon (MAC) pre-absorbed with Cl(-), SO4(2-), or PO4(3-) anions. Silver insoluble salts served as templates for the morphosynthesis of silver cages. The silver ions were reduced by reductive functional groups on MAC micropores through a galvanic cell reaction mechanism.

  2. 3D-Printed MOF Monoliths for Gas Adsorption Processes.

    Science.gov (United States)

    Thakkar, Harshul; Eastman, Stephen; Al-Naddaf, Qasim; Rownaghi, Ali Asghar; Rezaei, Fateme

    2017-09-27

    Metal-Organic Frameworks (MOFs) have shown promising performance in separation, adsorption, reaction and storage of various industrial gases, however, their large-scale applications have been hampered by the lack of a proper strategy to formulate them into scalable gas-solid contactors. Herein, we report fabrication of MOF monoliths using 3D printing technique and evaluation of their adsorptive performance in CO2 removal from air. The 3D-printed MOF-74(Ni) and UTSA-16(Co) monoliths with MOF loadings as high as 80 and 85 wt %, respectively were developed and their physical and structural properties were characterized and compared with those of MOF powders. Our adsorption experiments showed that upon exposure to 5,000 ppm (0.5%) CO2 at 25 ºC, the MOF-74(Ni) and UTSA-16(Co) monoliths can adsorb CO2 with the uptake capacity of 1.35 and 1.31 mmol/g, respectively, which are 79 and 87% of the capacity of their MOF analogues under the same conditions. Furthermore, a stable performance was obtained for self-standing 3D-printed monolithic structures with relatively good adsorption kinetics. The preliminary findings reported in this investigation highlight the advantage of robocasting (3D printing) technique for shaping MOF materials into practical configurations that are suitable for various gas separation applications.

  3. From 1D to 3D - macroscopic nanowire aerogel monoliths.

    Science.gov (United States)

    Cheng, Wei; Rechberger, Felix; Niederberger, Markus

    2016-08-01

    Here we present a strategy to assemble one-dimensional nanostructures into a three-dimensional architecture with macroscopic size. With the assistance of centrifugation, we successfully gel ultrathin W18O49 nanowires with diameters of 1 to 2 nm and aspect ratios larger than 100 into 3D networks, which are transformed into monolithic aerogels by supercritical drying.

  4. Minerals Yearbook, volume I, Metals and Minerals

    Science.gov (United States)

    ,

    2017-01-01

    The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

  5. Miscellaneous Industrial Mineral Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes miscellaneous industrial minerals operations in the United States. The data represent commodities covered by the Minerals Information Team...

  6. Performance of the Fluidized Bed Steam Reforming product under hydraulically unsaturated conditions

    Energy Technology Data Exchange (ETDEWEB)

    Neeway, James J [ORNL; Rod, Kenton A. [Pacific Northwest National Laboratory (PNNL); Bowden, Mark E [Pacific Northwest National Laboratory (PNNL); Pierce, Eric M [ORNL; Qafoku, Nikolla [Pacific Northwest National Laboratory (PNNL); Williams, Benjamin D [Pacific Northwest National Laboratory (PNNL); Brown, Christopher F [Pacific Northwest National Laboratory (PNNL)

    2014-01-01

    Several candidates for supplemental low-activity waste (LAW) immobilization at the Hanford site in Washington State, USA are being considered. One waste sequestering technology considered is Fluidized Bed Steam Reforming (FBSR). The granular product resulting from the FBSR process is composed primarily of an insoluble sodium aluminosilicate matrix with the dominant phases being feldspathoid minerals with a 1:1:1 molar ratio of Na, Al and Si. To demonstrate the durability of the product, which can be disposed of at the unsaturated Integrated Disposal Facility (IDF) at Hanford, a series of tests has been performed using the Pressurized Unsaturated Flow (PUF) system, which allows for the accelerated weathering of the solid materials. The system maintains hydraulically unsaturated conditions, thus mimicking the open-flow and transport properties that will be present at the IDF. Two materials were tested using the system: 1) the FBSR granular product and 2) the FBSR granular product encapsulated in a geopolymer to form a monolith. Results of the experiments show a trend of relatively constant effluent concentration of Na, Si, Al, and Cs as a function of time from both materials. The elements I and Re show a steady release throughout the yearlong test from the granular material but their concentrations seem to be increasing at one year from the monolith material. This result suggests that these two elements may be present in the sodalite cage structure rather than in the predominant nepheline phase because their release occurs at a different rate compared to nepheline phase. Also, these elements to not seem to reprecipitate when released from the starting material. Calculated one-year release rates for Si are on the order of 10 6 g/(m2 d) for the granular material and 10 5 g/(m2 d) for the monolith material while Re release is seen to be two orders of magnitude higher than Si release rates. SEM imaging and XRD analysis show how the alteration of the two materials is

  7. Determinants of pathologic mineralization.

    Science.gov (United States)

    Kirsch, Thorsten

    2008-01-01

    Physiologic mineralization is necessary for the formation of skeletal tissues and for their appropriate functions during adulthood. Mineralization has to be controlled and restricted to specific regions. If the mineralization process occurs in regions that normally do not mineralize, there can be severe consequences (pathologic or ectopic mineralization). Recent findings have indicated that physiologic and pathologic mineralization events are initiated by matrix vesicles, membrane-enclosed particles released from the plasma membranes of mineralization-competent cells. The understanding of how these vesicles are released from the plasma membrane and initiate the mineralization process may provide novel therapeutic strategies to prevent pathologic mineralization. In addition, other regulators (activators and inhibitors) of physiologic mineralization have been identified and characterized, and there is evidence that the same factors also contribute to the regulation of pathologic mineralization. Finally, programmed cell death (apoptosis) may be a contributor to physiologic mineralization and if occurring after tissue injury may induce pathologic mineralization and mineralization-related differentiation events in the injured and surrounding areas. This review describes how the understanding of mechanisms and factors regulating physiologic mineralization can be used to develop new therapeutic strategies to prevent pathologic or ectopic mineralization events.

  8. Piezoresistive Sensors Development Using Monolithic CMOS MEMS Technology

    Directory of Open Access Journals (Sweden)

    A. Chaehoi

    2011-04-01

    Full Text Available This paper presents the development of a monolithic CMOS-MEMS platform under the iDesign and SemeMEMS projects with the aim of jointly providing an open access “one-stop-shop” design and prototyping facility for integrated CMOS-MEMS. This work addresses the implementation of a 3-axis accelerometer and a pressure sensor using Semefab’s in-house 2-poly 1-metal CMOS process on a 380/4/15 μm SOI wafer; the membrane and the proof mass being micromachined using double-sided Deep Reactive Ion Etching (DRIE. This monolithic approach promises, in high volume production and using low complexity processes, a dramatic cost reduction over hybrid sensors. Furthermore, the embedded signal conditioning and the low-noise level in polysilicon gauges enables high performance to be achieved by implementing dedicated on-chip amplification and filtering circuitry.

  9. Fabrication and characterization of monolithic solid oxide fuel cells

    Science.gov (United States)

    Minh, N. Q.; Horne, C. R.; Liu, F. S.; Moffatt, D. M.; Staszak, P. R.

    The monolithic solid oxide fuel cell (MSOFC) is an all-ceramic structure in which cell components are configured in a compact corrugated array. The MSOFC shows promise for use in a wide range of sizes (kilowatt to megawatt) and a broad spectrum of applications (electric utility, cogeneration, on-site, and aerospace power). A process based on the tape calendering technique is being developed for the fabrication of the MSOFC. MSOFC single cells have been fabricated by this process without cracking or delamination. Stacks of various sizes have been formed and processed to demonstrate fabricability of the monolithic structure. Extensive physical, chemical, electrical, and electrochemical characterization of fabricated samples has been carried out to confirm the required properties of each cell component. The characterization results reported have been used to support material and fabrication improvements.

  10. Low-bandgap, monolithic, multi-bandgap, optoelectronic devices

    Science.gov (United States)

    Wanlass, Mark W.; Carapella, Jeffrey J.

    2014-07-08

    Low bandgap, monolithic, multi-bandgap, optoelectronic devices (10), including PV converters, photodetectors, and LED's, have lattice-matched (LM), double-heterostructure (DH), low-bandgap GaInAs(P) subcells (22, 24) including those that are lattice-mismatched (LMM) to InP, grown on an InP substrate (26) by use of at least one graded lattice constant transition layer (20) of InAsP positioned somewhere between the InP substrate (26) and the LMM subcell(s) (22, 24). These devices are monofacial (10) or bifacial (80) and include monolithic, integrated, modules (MIMs) (190) with a plurality of voltage-matched subcell circuits (262, 264, 266, 270, 272) as well as other variations and embodiments.

  11. Design and Testing of Prototypic Elements Containing Monolithic Fuel

    Energy Technology Data Exchange (ETDEWEB)

    N.E. Woolstenhulme; M.K. Meyer; D.M. Wachs

    2011-10-01

    The US fuel development team has performed numerous irradiation tests on small to medium sized specimens containing low enriched uranium fuel designs. The team is now focused on qualification and demonstration of the uranium-molybdenum Base Monolithic Design and has entered the next generation of testing with the design and irradiation of prototypic elements which contain this fuel. The designs of fuel elements containing monolithic fuel, such as AFIP-7 (which is currently under irradiation) and RERTR-FE (which is currently under fabrication), are appropriate progressions relative to the technology life cycle. The culmination of this testing program will occur with the design, fabrication, and irradiation of demonstration products to include the base fuel demonstration and design demonstration experiments. Future plans show that design, fabrication, and testing activities will apply the rigor needed for a demonstration campaign.

  12. From 1D to 3D - macroscopic nanowire aerogel monoliths

    Science.gov (United States)

    Cheng, Wei; Rechberger, Felix; Niederberger, Markus

    2016-07-01

    Here we present a strategy to assemble one-dimensional nanostructures into a three-dimensional architecture with macroscopic size. With the assistance of centrifugation, we successfully gel ultrathin W18O49 nanowires with diameters of 1 to 2 nm and aspect ratios larger than 100 into 3D networks, which are transformed into monolithic aerogels by supercritical drying.Here we present a strategy to assemble one-dimensional nanostructures into a three-dimensional architecture with macroscopic size. With the assistance of centrifugation, we successfully gel ultrathin W18O49 nanowires with diameters of 1 to 2 nm and aspect ratios larger than 100 into 3D networks, which are transformed into monolithic aerogels by supercritical drying. Electronic supplementary information (ESI) available: Experimental details, SEM and TEM images, and digital photographs. See DOI: 10.1039/c6nr04429h

  13. Low-bandgap, monolithic, multi-bandgap, optoelectronic devices

    Energy Technology Data Exchange (ETDEWEB)

    Wanlass, Mark W.; Carapella, Jeffrey J.

    2016-01-05

    Low bandgap, monolithic, multi-bandgap, optoelectronic devices (10), including PV converters, photodetectors, and LED's, have lattice-matched (LM), double-heterostructure (DH), low-bandgap GaInAs(P) subcells (22, 24) including those that are lattice-mismatched (LMM) to InP, grown on an InP substrate (26) by use of at least one graded lattice constant transition layer (20) of InAsP positioned somewhere between the InP substrate (26) and the LMM subcell(s) (22, 24). These devices are monofacial (10) or bifacial (80) and include monolithic, integrated, modules (MIMs) (190) with a plurality of voltage-matched subcell circuits (262, 264, 266, 270, 272) as well as other variations and embodiments.

  14. Low-bandgap, monolithic, multi-bandgap, optoelectronic devices

    Energy Technology Data Exchange (ETDEWEB)

    Wanlass, Mark W.; Carapella, Jeffrey J.

    2014-07-08

    Low bandgap, monolithic, multi-bandgap, optoelectronic devices (10), including PV converters, photodetectors, and LED's, have lattice-matched (LM), double-heterostructure (DH), low-bandgap GaInAs(P) subcells (22, 24) including those that are lattice-mismatched (LMM) to InP, grown on an InP substrate (26) by use of at least one graded lattice constant transition layer (20) of InAsP positioned somewhere between the InP substrate (26) and the LMM subcell(s) (22, 24). These devices are monofacial (10) or bifacial (80) and include monolithic, integrated, modules (MIMs) (190) with a plurality of voltage-matched subcell circuits (262, 264, 266, 270, 272) as well as other variations and embodiments.

  15. Low-bandgap, monolithic, multi-bandgap, optoelectronic devices

    Energy Technology Data Exchange (ETDEWEB)

    Wanlass, Mark W.; Carapella, Jeffrey J.

    2016-03-22

    Low bandgap, monolithic, multi-bandgap, optoelectronic devices (10), including PV converters, photodetectors, and LED's, have lattice-matched (LM), double-heterostructure (DH), low-bandgap GaInAs(P) subcells (22, 24) including those that are lattice-mismatched (LMM) to InP, grown on an InP substrate (26) by use of at least one graded lattice constant transition layer (20) of InAsP positioned somewhere between the InP substrate (26) and the LMM subcell(s) (22, 24). These devices are monofacial (10) or bifacial (80) and include monolithic, integrated, modules (MIMs) (190) with a plurality of voltage-matched subcell circuits (262, 264, 266, 270, 272) as well as other variations and embodiments.

  16. Development of stable monolithic wide-field Michelson interferometers

    Science.gov (United States)

    Wan, Xiaoke; Ge, Jian; Chen, Zhiping

    2011-07-01

    Bulk wide-field Michelson interferometers are very useful for high precision applications in remote sensing and astronomy. A stable monolithic Michelson interferometer is a key element in high precision radial velocity (RV) measurements for extrasolar planets searching and studies. Thermal stress analysis shows that matching coefficients of thermal expansion (CTEs) is a critical requirement for ensuring interferometer stability. This requirement leads to a novel design using BK7 and LAK7 materials, such that the monolithic interferometer is free from thermal distortion. The processes of design, fabrication, and testing of interferometers are described in detail. In performance evaluations, the field angle is typically 23.8° and thermal sensitivity is typically -2.6×10-6/° C near 550nm, which corresponds to ˜800m/s/°C in the RV scale. Low-cost interferometer products have been commissioned in multiple RV instruments, and they are producing high stability performance over long term operations.

  17. Development of stable monolithic wide-field Michelson interferometers.

    Science.gov (United States)

    Wan, Xiaoke; Ge, Jian; Chen, Zhiping

    2011-07-20

    Bulk wide-field Michelson interferometers are very useful for high precision applications in remote sensing and astronomy. A stable monolithic Michelson interferometer is a key element in high precision radial velocity (RV) measurements for extrasolar planets searching and studies. Thermal stress analysis shows that matching coefficients of thermal expansion (CTEs) is a critical requirement for ensuring interferometer stability. This requirement leads to a novel design using BK7 and LAK7 materials, such that the monolithic interferometer is free from thermal distortion. The processes of design, fabrication, and testing of interferometers are described in detail. In performance evaluations, the field angle is typically 23.8° and thermal sensitivity is typically -2.6×10(-6)/°C near 550 nm, which corresponds to ∼800 m/s/°C in the RV scale. Low-cost interferometer products have been commissioned in multiple RV instruments, and they are producing high stability performance over long term operations.

  18. Affinity Monolith-Integrated Microchips for Protein Purification and Concentration.

    Science.gov (United States)

    Gao, Changlu; Sun, Xiuhua; Wang, Huaixin; Qiao, Wei; Hu, Bo

    2016-01-01

    Affinity chromatography is a valuable method to purify and concentrate minute amount of proteins. Monoliths with epoxy groups for affinity immobilization were prepared by direct in-situ photopolymerization of glycidyl methacrylate and ethylene glycol dimethacrylate in porogenic solvents consisting of 1-dodecanol and cyclohexanol. By integrating affinity monoliths onto a microfluidic system, targeted biomolecules can be captured and retained on affinity column, while other biomolecules having no specific interactions toward the immobilized ligands flow through the microchannel. Therefore, proteins which remain on the affinity column are purified and concentrated, and then eluted by appropriate solutions and finally, separated by microchip capillary electrophoresis. This integrated microfluidic device has been applied to the purification and separation of specific proteins (FITC-labeled human serum albumin and IgG) in a mixture.

  19. Dynamic response of monolithic and laminate/particulate reactive mixtures

    OpenAIRE

    Wei, Chung-Ting

    2011-01-01

    Two dynamic compression methods were applied to a monolithic metal and reactive mixtures to investigate their responses: (a) Dynamic experiments using a split Hopkinson pressure bar were applied to reactive mixtures densified by explosive consolidation in order to establish their mechanical response and failure mechanisms. (b) Laser compression and release, which can impart high stresses, up to hundreds GPa, in times of nanoseconds and fractions thereof, was applied to establish the spalling ...

  20. Advanced on-chip divider for monolithic microwave VCO's

    Science.gov (United States)

    Peterson, Weddell C.

    1989-01-01

    High frequency division on a monolithic circuit is a critical technology required to significantly enhance the performance of microwave and millimeter-wave phase-locked sources. The approach used to meet this need is to apply circuit design practices which are essentially 'microwave' in nature to the basically 'digital' problem of high speed division. Following investigation of several promising circuit approaches, program phase 1 culminated in the design and layout of an 8.5 GHz (Deep Space Channel 14) divide by four circuit based on a dynamic mixing divider circuit approach. Therefore, during program phase 2, an 8.5 GHz VCO with an integral divider which provides a phase coherent 2.125 GHz reference signal for phase locking applications was fabricated and optimized. Complete phase locked operation of the monolithic GaAs devices (VCO, power splitter, and dynamic divider) was demonstrated both individually and as an integrated unit. The fully functional integrated unit in a suitable test fixture was delivered to NASA for engineering data correlation. Based on the experience gained from this 8.5 GHz super component, a monolithic GaAs millimeter-wave dynamic divider for operation with an external VCO was also designed, fabricated, and characterized. This circuit, which was also delivered to NASA, demonstrated coherent division by four at an input frequency of 24.3 GHz. The high performance monolithic microwave VCO with a coherent low frequency reference output described in this report and others based on this technology will greatly benefit advanced communications systems in both the DoD and commercial sectors. Signal processing and instrumentation systems based on phase-locking loops will also attain enhanced performance at potentially reduced cost.

  1. Advanced on-chip divider for monolithic microwave VCO's

    Science.gov (United States)

    Peterson, Weddell C.

    1989-05-01

    High frequency division on a monolithic circuit is a critical technology required to significantly enhance the performance of microwave and millimeter-wave phase-locked sources. The approach used to meet this need is to apply circuit design practices which are essentially 'microwave' in nature to the basically 'digital' problem of high speed division. Following investigation of several promising circuit approaches, program phase 1 culminated in the design and layout of an 8.5 GHz (Deep Space Channel 14) divide by four circuit based on a dynamic mixing divider circuit approach. Therefore, during program phase 2, an 8.5 GHz VCO with an integral divider which provides a phase coherent 2.125 GHz reference signal for phase locking applications was fabricated and optimized. Complete phase locked operation of the monolithic GaAs devices (VCO, power splitter, and dynamic divider) was demonstrated both individually and as an integrated unit. The fully functional integrated unit in a suitable test fixture was delivered to NASA for engineering data correlation. Based on the experience gained from this 8.5 GHz super component, a monolithic GaAs millimeter-wave dynamic divider for operation with an external VCO was also designed, fabricated, and characterized. This circuit, which was also delivered to NASA, demonstrated coherent division by four at an input frequency of 24.3 GHz. The high performance monolithic microwave VCO with a coherent low frequency reference output described in this report and others based on this technology will greatly benefit advanced communications systems in both the DoD and commercial sectors. Signal processing and instrumentation systems based on phase-locking loops will also attain enhanced performance at potentially reduced cost.

  2. Clinical assessment of enamel wear caused by monolithic zirconia crowns.

    Science.gov (United States)

    Stober, T; Bermejo, J L; Schwindling, F S; Schmitter, M

    2016-08-01

    The purpose of this study was to measure enamel wear caused by antagonistic monolithic zirconia crowns and to compare this with enamel wear caused by contralateral natural antagonists. Twenty monolithic zirconia full molar crowns were placed in 20 patients. Patients with high activity of the masseter muscle at night (bruxism) were excluded. For analysis of wear, vinylpolysiloxane impressions were prepared after crown incorporation and at 6-, 12-, and 24-month follow-up. Wear of the occlusal contact areas of the crowns, of their natural antagonists, and of two contralateral natural antagonists (control teeth) was measured by use of plaster replicas and a 3D laser-scanning device. Differences of wear between the zirconia crown antagonists and the control teeth were investigated by means of two-sided paired Student's t-tests and linear regression analysis. After 2 years, mean vertical loss was 46 μm for enamel opposed to zirconia, 19-26 μm for contralateral control teeth and 14 μm for zirconia crowns. Maximum vertical loss was 151 μm for enamel opposed to zirconia, 75-115 μm for control teeth and 60 μm for zirconia crowns. Statistical analysis revealed significant differences between wear of enamel by zirconia-opposed teeth and by control teeth. Gender, which significantly affected wear, was identified as a possible confounder. Monolithic zirconia crowns generated more wear of opposed enamel than did natural teeth. Because of the greater wear caused by other dental ceramics, the use of monolithic zirconia crowns may be justified.

  3. Applications of monolithic fiber interferometers and actively controlled fibers

    OpenAIRE

    Rugeland, Patrik

    2013-01-01

    The objective of this thesis was to develop applications of monolithic fiber devices and actively controlled fibers. A special twin-core fiber known as a ‘Gemini’ fiber was used to construct equal arm-length fiber interferometers, impervious to temperature and mechanical perturbations. A broadband add/drop multiplexer was constructed by inscribing fiber Bragg gratings in the arms of a Gemini Mach-Zehnder interferometer. A broadband interferometric nanosecond switch was constructed from a micr...

  4. Monolithically Integrated Ge-on-Si Active Photonics

    OpenAIRE

    Jifeng Liu

    2014-01-01

    Monolithically integrated, active photonic devices on Si are key components in Si-based large-scale electronic-photonic integration for future generations of high-performance, low-power computation and communication systems. Ge has become an interesting candidate for active photonic devices in Si photonics due to its pseudo-direct gap behavior and compatibility with Si complementary metal oxide semiconductor (CMOS) processing. In this paper, we present a review of the recent progress in Ge-on...

  5. Extended Leach Testing of Simulated LAW Cast Stone Monoliths

    Energy Technology Data Exchange (ETDEWEB)

    Serne, R. Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lanigan, David C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Williams, Benjamin D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jung, H. B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wang, Guohui [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-08-12

    This revision to the original report adds two longer term leach sets of data to the report and provides more discussion and graphics on how to interpret the results from long-term laboratory leach tests. The leach tests were performed at Pacific Northwest National Laboratory (PNNL) for Washington River Protection Solutions (WRPS) to evaluate the release of key constituents from monoliths of Cast Stone prepared with four simulated low-activity waste (LAW) liquid waste streams.

  6. A Distributed Model of Four-Port Monolithic Transformer

    OpenAIRE

    Lee, Dong Ho; Ko, Sangsoo; Jeon, Sang-Hoon; Park, Jae-Woo; Hong, Songcheol

    2004-01-01

    This paper deals with modeling of a monolithic spiral transformer. The transformer is designed and fabricated as a symmetrical octagonal spiral structure using two-metal layer process on GaAs substrate for input balun applications of 2 GHz and 5 GHz push-pull power amplifiers. A distributed model of the transformer is developed to fit in wide frequency range with four ports. The model includes the skin effect which describes increase in series resistance with frequency. Six different se...

  7. UPDATE ON MECHANICAL ANALYSIS OF MONOLITHIC FUEL PLATES

    Energy Technology Data Exchange (ETDEWEB)

    D. E. Burkes; F. J. Rice; J.-F. Jue; N. P. Hallinan

    2008-03-01

    Results on the relative bond strength of the fuel-clad interface in monolithic fuel plates have been presented at previous RRFM conferences. An understanding of mechanical properties of the fuel, cladding, and fuel / cladding interface has been identified as an important area of investigation and quantification for qualification of monolithic fuel forms. Significant progress has been made in the area of mechanical analysis of the monolithic fuel plates, including mechanical property determination of fuel foils, cladding processed by both hot isostatic pressing and friction bonding, and the fuel-clad composite. In addition, mechanical analysis of fabrication induced residual stress has been initiated, along with a study to address how such stress can be relieved prior to irradiation. Results of destructive examinations and mechanical tests are presented along with analysis and supporting conclusions. A brief discussion of alternative non-destructive evaluation techniques to quantify not only bond quality, but also bond integrity and strength, will also be provided. These are all necessary steps to link out-of-pile observations as a function of fabrication with in-pile behaviours.

  8. Optimal parameters of monolithic high-index contrast grating VCSELs

    Science.gov (United States)

    Marciniak, Magdalena; Gebski, Marcin; Dems, Maciej; Czyszanowski, Tomasz

    2016-04-01

    Monolithic High refractive index Contrast Grating (MHCG) allows several-fold size reduction of epitaxial structure of VCSEL and facilitates VCSEL fabrication in all photonic material systems. MHCGs can be fabricated of material which refractive index is higher than 1.75 without the need of the combination of low and high refractive index materials. MHCGs have a great application potential in optoelectronic devices, especially in phosphide- and nitride-based VCSELs, which suffer from the lack of efficient monolithically integrated DBR mirrors. MHCGs can simplify the construction of VCSELs, reducing their epitaxial design to monolithic wafer with carrier confinement and active region inside and etched stripes on both surfaces in post processing. In this paper we present results of numerical analysis of MHCGs as a high reflective mirrors for broad range of refractive indices that corresponds to plethora of materials typically used in optoelectronics. Our calculations base on a three-dimensional, fully vectorial optical model. We investigate the reflectance of the MHCG mirrors of different design as the function of the refractive index and we show the optimal geometrical parameters of MHCG enabling nearly 100% reflectance and broad reflection stop-band. We show that MHCG can be designed based on most of semiconductors materials and for any incident light wavelength from optical spectrum.

  9. A Ferrite LTCC-Based Monolithic SIW Phased Antenna Array

    KAUST Repository

    Nafe, Ahmed

    2016-11-17

    In this work, we present a novel configuration for realizing monolithic SIW-based phased antenna arrays using Ferrite LTCC technology. Unlike the current common schemes for realizing SIW phased arrays that rely on surface-mount component (p-i-n diodes, etc) for controlling the phase of the individual antenna elements, here the phase is tuned by biasing of the ferrite filling of the SIW. This approach eliminates the need for mounting of any additional RF components and enables seamless monolithic integration of phase shifters and antennas in SIW technology. As a proof of concept, a two-element slotted SIW-based phased array is designed, fabricated and measured. The prototype exhibits a gain of 4.9 dBi at 13.2 GHz and a maximum E-plane beam-scanning of 28 degrees using external windings for biasing the phase shifters. Moreover, the array can achieve a maximum beam-scanning of 19 degrees when biased with small windings that are embedded in the package. This demonstration marks the first time a fully monolithic SIW-based phased array is realized in Ferrite LTCC technology and paves the way for future larger-size implementations.

  10. Strong cation exchange monoliths for HPLC by Reactive Gelation.

    Science.gov (United States)

    Brand, Bastian; Krättli, Martin; Storti, Giuseppe; Morbidelli, Massimo

    2011-08-01

    Polymeric monolithic stationary phases for HPLC can be produced by Reactive Gelation. Unlike the conventional method of using porogens, such novel process consists of a number of separate steps, thus enabling a better control of the quality of the final material. A suspension of polymer nanoparticles in water is produced and subsequently swollen with hydrophobic monomers. The particles are then destabilised (usually by salt addition) to make them aggregate into a large percolating structure, the so-called monolith. Finally, the added monomer can then be polymerised to harden the structure. In this work, a polystyrene latex is used as the base material and functionalised by introduction of epoxide groups on the surface and subsequent reaction to sulphonic acid groups, yielding a SO3(-) density of 0.7 mmol/g dry material. Morphological investigations show 54% porosity made of 300 nm large pores. Van Deemter measurements of a large protein show no practical influence of diffusion limitations on the plate number. Finally, a preliminary separation of a test protein mixture is shown, demonstrating the potential of using ion-exchange chromatography on Reactive Gelation monoliths.

  11. Controlled porosity monolithic material as permselective ion exchange membranes.

    Science.gov (United States)

    Huang, Xiaojia; Dasgupta, Purnendu K

    2011-03-18

    Ion exchange membranes (IEMs) are used in a variety of analytical devices, including suppressors, eluent generators and other components used in ion chromatography. Such membranes are flexible and undergo substantial dimensional changes on hydration. Presently the push to miniaturization continues; a resurgent interest in open tubular ion chromatography requires microscale adaptation of these components. Incorporating IEMs in microscale devices is difficult. Although both macroporous and microporous ion exchange materials have been made for use as chromatographic packing, ion exchange material used as membranes are porous only on a molecular scale. Because such pores have vicinal ion exchange sites, ions of the same charge sign as those of the fixed sites are excluded from the IEMs. Monolithic polymers, including ion exchangers derived therefrom, are presently extensively used. When used in a separation column, such a monolithic structure contains an extensively connected porous network. We show here that by controlling the amount of porogen added during the synthesis of monolithic polymers derived from ethylene dimethacrylate - glycidyl methacrylate, which are converted to an anion exchanger by treatment with trimethylamine, it is possible to obtain rigid ion exchange polymers that behave like IEMs and allow only one charge type of ions to pass through, i.e., are permselective. We demonstrate successful open tubular cation chromatography suppressor performance.

  12. Monolithic pixels on moderate resistivity substrate and sparsifying readout architecture

    Science.gov (United States)

    Giubilato, P.; Battaglia, M.; Bisello, D.; Caselle, M.; Chalmet, P.; Demaria, L.; Ikemoto, Y.; Kloukinas, K.; Mansuy, S. C.; Mattiazzo, S.; Marchioro, A.; Mugnier, H.; Pantano, D.; Potenza, A.; Rivetti, A.; Rousset, J.; Silvestrin, L.; Snoeys, W.

    2013-12-01

    The LePix projects aim realizing a new generation monolithic pixel detectors with improved performances at lesser cost with respect to both current state of the art monolithic and hybrid pixel sensors. The detector is built in a 90 nm CMOS process on a substrate of moderate resistivity. This allows charge collection by drift while maintaining the other advantages usually offered by MAPS, like having a single piece detector and using a standard CMOS production line. The collection by drift mechanism, coupled to the low capacitance design of the collecting node made possible by the monolithic approach, provides an excellent signal to noise ratio straight at the pixel cell together with a radiation tolerance far superior to conventional un-depleted MAPS. The excellent signal-to-noise performance is demonstrated by the device ability to separate the 6 keV 55Fe double peak at room temperature. To achieve high granularity (10-20 μm pitch pixels) over large detector areas maintaining high readout speed, a completely new compressing architecture has been devised. This architecture departs from the mainstream hybrid pixel sparsification approach, which uses in-pixel logic to reduce data, by using topological compression to minimize pixel area and power consumption.

  13. Preparing silica aerogel monoliths via a rapid supercritical extraction method.

    Science.gov (United States)

    Carroll, Mary K; Anderson, Ann M; Gorka, Caroline A

    2014-02-28

    A procedure for the fabrication of monolithic silica aerogels in eight hours or less via a rapid supercritical extraction process is described. The procedure requires 15-20 min of preparation time, during which a liquid precursor mixture is prepared and poured into wells of a metal mold that is placed between the platens of a hydraulic hot press, followed by several hours of processing within the hot press. The precursor solution consists of a 1.0:12.0:3.6:3.5 x 10(-3) molar ratio of tetramethylorthosilicate (TMOS):methanol:water:ammonia. In each well of the mold, a porous silica sol-gel matrix forms. As the temperature of the mold and its contents is increased, the pressure within the mold rises. After the temperature/pressure conditions surpass the supercritical point for the solvent within the pores of the matrix (in this case, a methanol/water mixture), the supercritical fluid is released, and monolithic aerogel remains within the wells of the mold. With the mold used in this procedure, cylindrical monoliths of 2.2 cm diameter and 1.9 cm height are produced. Aerogels formed by this rapid method have comparable properties (low bulk and skeletal density, high surface area, mesoporous morphology) to those prepared by other methods that involve either additional reaction steps or solvent extractions (lengthier processes that generate more chemical waste).The rapid supercritical extraction method can also be applied to the fabrication of aerogels based on other precursor recipes.

  14. Monolithic pixels on moderate resistivity substrate and sparsifying readout architecture

    CERN Document Server

    Giubilato, P; Snoeys, W; Bisello, D; Marchioro, A; Battaglia, M; Demaria, L; Mansuy, S C; Pantano, D; Rousset, J; Mattiazzo, S; Kloukinas, K; Potenza, A; Ikemoto, Y; Rivetti, A; Chalmet, P; Mugnier, H; Silvestrin, L

    2013-01-01

    The LePix projects aim realizing a new generation monolithic pixel detectors with improved performances at lesser cost with respect to both current state of the art monolithic and hybrid pixel sensors. The detector is built in a 90 nm CMOS process on a substrate of moderate resistivity. This allows charge collection by drift while maintaining the other advantages usually offered by MAPS, like having a single piece detector and using a standard CMOS production line. The collection by drift mechanism, coupled to the low capacitance design of the collecting node made possible by the monolithic approach, provides an excellent signal to noise ratio straight at the pixel cell together with a radiation tolerance far superior to conventional un-depleted MAPS. The excellent signal-to-noise performance is demonstrated by the device ability to separate the 6 keV Fe-55 double peak at room temperature. To achieve high granularity (10-20 mu m pitch pixels) over large detector areas maintaining high readout speed, a complet...

  15. Preparation and characterization of polystyrene-based monolith with ordered macroporous structure

    Institute of Scientific and Technical Information of China (English)

    Quan Zhou Wu; Jian Feng He; Ji Ming Ou

    2012-01-01

    In this paper,polystyrene-based monoliths with highly ordered macroporous structure were synthesized by using SiO2 colloidal crystal as template.SEM observation shows that the macropores are highly ordered and are interconnected by small windows.The BET surface area of PS monolith is about 36.17 m2/g.The polymer monoliths can resist 5 MPa pressure,showing high mechanical and compressive strength.

  16. Photoinitiated grafting of porous polymer monoliths and thermoplastic polymers for microfluidic devices

    Science.gov (United States)

    Frechet, Jean M. J.; Svec, Frantisek; Rohr, Thomas

    2008-10-07

    A microfluidic device preferably made of a thermoplastic polymer that includes a channel or a multiplicity of channels whose surfaces are modified by photografting. The device further includes a porous polymer monolith prepared via UV initiated polymerization within the channel, and functionalization of the pore surface of the monolith using photografting. Processes for making such surface modifications of thermoplastic polymers and porous polymer monoliths are set forth.

  17. Application of Monolithic Zirconia Ceramics in Dental Practice: A Case History Report.

    Science.gov (United States)

    Kim, Hee-Kyung; Kim, Sung-Hun; Lee, Jai-Bong; Han, Jung-Suk; Yeo, In-Sung

    2016-01-01

    Monolithic zirconia restorations increasingly have been used in dental practice in recent years and demonstrate superior mechanical performance compared with porcelain-veneered zirconia restorations. Recent advances in manufacturing technology have made possible the fabrication of translucent monolithic zirconia ceramics. This case report describes three clinical examples of monolithic zirconia fixed dental prostheses being used in the anterior and posterior regions and exhibiting acceptable esthetic results.

  18. Process for the manufacture of a monolithic support for catalysts suitable for use in controlling carbon monoxide emissions

    Energy Technology Data Exchange (ETDEWEB)

    Paolasini, S.

    1981-07-07

    A monolithic support for a catalyst suitable for use in controlling carbon monoxide emission is prepared by forming a homogeneous, fluid semi-solid mass by admixing colloidal gamma alumina, alpha alumina monohydrate and ceramic fibres with fluidizing and binding agents, water and a mineral acid, said acid being used in an amount sufficient to convert said alpha Al/sub 2/O/sub 3/ monohydrate into a gel, forming the mass into a body of the desired shape, drying the body to substantially remove the added water, at least 10% of said added water being removed at a temperature lower than 50/sup 0/ C., and heat-treating the dried body at 800/sup 0/-1000/sup 0/ C.

  19. Feasibility evaluation of the monolithic braided ablative nozzle

    Science.gov (United States)

    Director, Mark N.; McPherson, Douglass J., Sr.

    1992-02-01

    The feasibility of the monolithic braided ablative nozzle was evaluated as part of an independent research and development (IR&D) program complementary to the National Aeronautics and Space Administration/Marshall Space Flight Center (NASA/MSFC) Low-Cost, High-Reliability Case, Insulation and Nozzle for Large Solid Rocket Motors (LOCCIN) Program. The monolithic braided ablative nozzle is a new concept that utilizes a continuous, ablative, monolithic flame surface that extends from the nozzle entrance, through the throat, to the exit plane. The flame surface is fabricated using a Through-the-Thickness braided carbon-fiber preform, which is impregnated with a phenolic or phenolic-like resin. During operation, the braided-carbon fiber/resin material ablates, leaving the structural backside at temperatures which are sufficiently low to preclude the need for any additional insulative materials. The monolithic braided nozzle derives its potential for low life cycle cost through the use of automated processing, one-component fabrication, low material scrap, low process scrap, inexpensive raw materials, and simplified case attachment. It also has the potential for high reliability because its construction prevents delamination, has no nozzle bondlines or leak paths along the flame surface, is amenable to simplified analysis, and is readily inspectable. In addition, the braided construction has inherent toughness and is damage-tolerant. Two static-firing tests were conducted using subscale, 1.8 - 2.0-inch throat diameter, hardware. Tests were approximately 15 seconds in duration, using a conventional 18 percent aluminum/ammonium perchlorate propellant. The first of these tests evaluated the braided ablative as an integral backside insulator and exit cone; the second test evaluated the monolithic braided ablative as an integral entrance/throat/exit cone nozzle. Both tests met their objectives. Radial ablation rates at the throat were as predicted, approximately 0.017 in

  20. Comparison of perfusion media and monoliths for protein and virus-like particle chromatography.

    Science.gov (United States)

    Wu, Yige; Abraham, Dicky; Carta, Giorgio

    2016-05-20

    Structural and performance characteristics of perfusion chromatography media (POROS HS 20 and 50) and those of a polymethacrylate monolith (CIM SO3-1 tube monolith column) are compared for protein and virus-like particle chromatography using 1mL columns. Axial flow columns are used for POROS while the monolith has a radial flow configuration, which provides comparable operating pressures. The POROS beads contain a bimodal distribution of pore sizes, some as large as 0.5μm, which allow a small fraction of the mobile phase to flow within the particles, while the monolith contains 1-2μm flow channels. For proteins (lysozyme and IgG), the dynamic binding capacity of the POROS columns is more than twice that of the monolith at longer residence times. While the DBC of the POROS HS 50 column decreases at shorter residence times, the DBC of the POROS HS 20 column for IgG remains nearly twice that of the monolith at residence times at least as low as 0.2min as a result of intraparticle convection. Protein recoveries are comparable for all three columns. For VLPs, however, the eluted peaks are broader and recovery is lower for the monolith than for the POROS columns and is dependent on the direction of flow in the monolith, which is attributed to denser layer observed by SEM at the inlet surface of the monolith that appears to trap VLPs when loading in the normal flow direction.

  1. Mineral resources of Australia

    Energy Technology Data Exchange (ETDEWEB)

    Kelsall, D.F.; Woodcock, J.T. (eds.)

    1979-01-01

    The papers presented cover geological, geochemical technology and geophysics in mineral exploration, mineral resources, mining methods and technology, aspects of beneficiation, pyrometallurgy and hydrometallurgy, and environmental aspects. 4 of the 14 papers have been abstracted separately.

  2. Construction Minerals Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes construction minerals operations in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  3. Agricultural Minerals Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes agricultural minerals operations in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  4. Mineral Resources Data System

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — Mineral resource occurrence data covering the world, most thoroughly within the U.S. This database contains the records previously provided in the Mineral Resource...

  5. Mineral Supply Challenges

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Faced with shortcomings in its mineral supply, it’s imperative for China to balance its desire for reserves with its current economic needs Mineral resources are the corner- stone of materials needed for China’s national economic and social development.The country even counts on its mineral resources to satisfy 90 percent of its energy demands and over 95

  6. Reprocessing of LEU U-Mo Dispersion and Monolithic Fuels

    Energy Technology Data Exchange (ETDEWEB)

    Vandegrift, G.F.; Jerden, J.; Stepinski, D.C.; Figueroa, J.; Williamson, M.A.; Kleeck, M.A. Van; Blaskovitz, R.J.; Ziegler, A.J.; Maggos, L.E.; Swanson, J.; Fortner, J.; Bakel, A.J. [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 S. Cass Ave., Argonne, IL 60439 (United States)

    2011-07-01

    For conversion of high-performance research reactors from high-enriched uranium (HEU) to low-enriched uranium (LEU) fuel, a fuel material with a higher density than uranium aluminide is required. Development studies are underway to develop U-Mo dispersion and monolithic fuels for conversion of several high- performance reactors. For dispersion fuels, development is narrowing down to a composition of U-7Mo dispersed in an aluminium matrix containing {approx}5% silicon. For monolithic fuels to be used in high performance research reactors in the United States, a zirconium-bonded U-10Mo foil appears to be the fuel of choice. For conversion to be realized a back-end disposition path is required for both fuels; one disposition pathway is reprocessing. Argonne National Laboratory is developing a pyroprocess for reprocessing spent monolithic fuel. Pyroprocessing was chosen over conventional aqueous solvent extraction due to the necessity of adding fluoride to the fuel-dissolution solution in order to dissolve the zirconium bonding layer on the U-Mo fuel. The proposed flowsheet and development activities will be described. A literature survey points to the ability to reprocess U-Mo dispersion fuels by an aqueous process, but due to several special characteristics of the fuel, the solvent-extraction flowsheets will be a departure from that normally used for the reprocessing of power reactor fuel. Special concerns that must be addressed in reprocessing these fuels are, for example, the low solubilities of uranyl molybdate, molybdic acid, and silicic acid in nitric acid solutions. This paper will address these concerns and development activities required to overcome them. (author)

  7. 10Gbps monolithic silicon FTTH transceiver for PON

    Science.gov (United States)

    Zhang, J.; Liow, T. Y.; Lo, G. Q.; Kwong, D. L.

    2010-05-01

    We propose a new passive optical network (PON) configuration and a novel silicon photonic transceiver architecture for optical network unit (ONU), eliminating the need for an internal laser source in ONU. We adopt dual fiber network configuration. The internal light source in each of the ONUs is eliminated. Instead, an extra seed laser source in the optical line termination (OLT) operates in continuous wave mode to serve the ONUs in the PON as a shared and centralized laser source. λ1 from OLT Tx and λ2 from the seed laser are combined by using a WDM combiner and connected to serve the multiple ONUs through the downstream fibers. The ONUs receive the data in λ1. Meanwhile, the ONUs encode and transmit data in λ2, which are sent back to OLT. The monolithic ONU transceiver contains a wavelength-division-multiplexing (WDM) filter component, a silicon modulator and a Ge photo-detector. The WDM in ONU selectively guides λ1 to the Ge-PD where the data in λ1 are detected and converted to electrical signals, and λ2 to the transmitter where the light is modulated by upstream data. The modulated optical signals in λ2 from ONUs are connected back to OLT through upstream fibers. The monolithic ONU transceiver chip size is only 2mm by 4mm. The crosstalk between the Tx and Rx is measured to be less than -20dB. The transceiver chip is integrated on a SFP+ transceiver board. Both Tx and Rx demonstrated data rate capabilities of up to 10Gbps. By implementing this scheme, the ONU transceiver size can be significantly reduced and the assembly processes will be greatly simplified. The results demonstrate the feasibility of mass manufacturing monolithic silicon ONU transceivers via low cost

  8. W-band monolithic oscillator using InAlAs/InGaAs HEMT

    Science.gov (United States)

    Kwon, Y.; Pavlidis, D.; Tutt, M.; Ng, G. I.; Lai, R.

    1990-01-01

    A W-band monolithic integrated oscillator circuit was designed and fabricated using submicron HEMT technology. The oscillation frequency was around 81 GHz and the power was -7 dBm at the chip level. This is the first report of an InAlAs/InGaAs monolithic oscillator operating at the W-band.

  9. Recent advances in the preparation and application of monolithic capillary columns in separation science

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Tingting; Yang, Xi; Xu, Yujing [Department of Analytical Chemistry, China Pharmaceutical University, Nanjing, 210009 (China); Key Laboratory of Drug Quality Control and Pharmacovigilance, Ministry of Education, Nanjing, 210009 (China); Ji, Yibing, E-mail: jiyibing@msn.com [Department of Analytical Chemistry, China Pharmaceutical University, Nanjing, 210009 (China); Key Laboratory of Drug Quality Control and Pharmacovigilance, Ministry of Education, Nanjing, 210009 (China)

    2016-08-10

    Novel column technologies involving various materials and efficient reactions have been investigated for the fabrication of monolithic capillary columns in the field of analytical chemistry. In addition to the development of these miniaturized systems, a variety of microscale separation applications have achieved noteworthy results, providing a stepping stone for new types of chromatographic columns with improved efficiency and selectivity. Three novel strategies for the preparation of capillary monoliths, including ionic liquid-based approaches, nanoparticle-based approaches and “click chemistry”, are highlighted in this review. Furthermore, we present the employment of state-of-the-art capillary monolithic stationary phases for enantioseparation, solid-phase microextraction, mixed-mode separation and immobilized enzyme reactors. The review concludes with recommendations for future studies and improvements in this field of research. - Highlights: • Preparation of novel monolithic capillary columns have shown powerful potential in analytical chemistry field. • Various materials including ionic liquids and nanoparticles involved into capillary monolithic micro-devices are concluded. • Click chemistry strategy applied for preparing monolithic capillary columns is reviewed. • Recent strategies utilized in constructing different capillary monoliths for enantiomeric separation are summarized. • Advancement of capillary monoliths for complex samples analysis is comprehensively described.

  10. Preparation and applications of hybrid organic-inorganic monoliths: a review.

    Science.gov (United States)

    Zhu, Tao; Row, Kyung Ho

    2012-06-01

    This review presents an overview of the properties of hybrid organic-inorganic monolithic materials and summarizes the recent developments in the preparation and applications of these hybrid monolithic materials. Hybrid monolithic materials with porosities, surface functionalities, and fast dynamic transport have developed rapidly, and have been used in a wide range of applications owing to the low cost, good stability, and excellent performance. Basically, these materials can be divided into two major types according to the chemical composition: hybrid silica-based monolith (HSM) and hybrid polymer-based monolith (HPM). Compared to the HPM, HSM monolith has been attracting most wide attentions, and it is commonly synthesized by the sol-gel process. The conventional preparation procedures of two type's hybrid organic-inorganic monoliths are addressed. Applications of hybrid organic-inorganic monoliths in optical devices, capillary microextraction (CME), capillary electrochromatography (CEC), high performance liquid chromatography (HPLC), and chiral separation are also reviewed. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Preparation of a zeolite-modified polymer monolith for identification of synthetic colorants in lipsticks

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Huiqi; Li, Zheng [College of Chemistry, Jilin University, Changchun 130012 (China); Niu, Qian [Jilin Entry-Exit Inspection and Quarantine Bureau, Changchun 130062 (China); Ma, Jiutong [College of Chemistry, Jilin University, Changchun 130012 (China); Jia, Qiong, E-mail: jiaqiong@jlu.edu.cn [College of Chemistry, Jilin University, Changchun 130012 (China)

    2015-10-30

    Graphical abstract: Poly(methacrylic acid-ethylene dimethacrylate) monolithic column embedded with zeolites was prepared and employed for the polymer monolith microextraction of colorants combined with HPLC. - Highlights: • Zeolite, as a kind of mesoporous material, was firstly combined with PMME. • Zeolite@poly(MAA-EDMA) monolith columns were prepared for the enrichment of colorants. • Zeolite@poly(MAA-EDMA) monolith columns demonstrated relatively high extraction capacity. - Abstract: A novel zeolite-modified poly(methacrylic acid-ethylenedimethacrylate) (zeolite@poly(MAA-EDMA)) monolithic column was prepared with the in situ polymerization method and employed in polymer monolith microextraction for the separation and preconcentration of synthetic colorants combined with high performance liquid chromatography. The polymer was characterized by scanning electronmicroscopy, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and thermo-gravimetric analysis. Various parameters affecting the extraction efficiency were investigated and optimized. Under the optimum experimental conditions, we obtained acceptable linearities, low limits of detection, and good intra-day/inter-day relative standard deviations. The method was applied to the determination of synthetic colorants in lipsticks with recoveries ranged from 70.7% to 109.7%. Compared with conventional methacrylic acid-based monoliths, the developed monolith exhibited high enrichment capacity because of the introduction of zeolites into the preparation process. The extraction efficiency followed the order: zeolite@poly(MAA-EDMA) > poly(MAA-EDMA) > direct HPLC analysis.

  12. Hydrophobic polymer monoliths as novel phase separators: Application in continuous liquid-liquid extraction systems

    NARCIS (Netherlands)

    Peroni, D.; Vanhoutte, D.; Vilaplana, F.; Schoenmakers, P.; de Koning, S.; Janssen, H.-G.

    2012-01-01

    Hydrophobic macroporous polymer monoliths are shown to be interesting materials for the construction of "selective solvent gates". With the appropriate surface chemistry and porous properties the monoliths can be made permeable only for apolar organic solvents and not for water. Different poly(butyl

  13. Functionalization of hybrid monolithic columns via thiol-ene click reaction for proteomics analysis.

    Science.gov (United States)

    Liu, Zhongshan; Liu, Jing; Liu, Zheyi; Wang, Hongwei; Ou, Junjie; Ye, Mingliang; Zou, Hanfa

    2017-05-19

    The vinyl-functionalized hybrid monolithic columns (75 and 150μm i.d.) were prepared via sol-gel chemistry of tetramethoxysilane (TMOS) and vinyltrimethoxysilane (VTMS). The content of accessible vinyl groups was further improved after the monolithic column was post-treated with vinyldimethylethoxysilane (VDMES). The surface properties of monolithic columns were tailored via thiol-ene click reaction by using 1-octadecanethiol, sodium 3-mercapto-1-propanesulfonate and 2,2'-(ethylenedioxy)diethanethiol/vinylphosphonic acid, respectively. The preparing octadecyl-functionalized monolithic columns were adopted for proteomics analysis in cLC-MS/MS. A 37-cm-long×75-μm-i.d. monolithic column could identify 3918 unique peptides and 1067 unique proteins in the tryptic digest of proteins from HeLa cells. When a 90-cm-long×75-μm-i.d. monolithic column was used, the numbers of unique peptides and proteins were increased by 82% and 32%, respectively. Furthermore, strong cation exchange (SCX) monolithic columns (4cm in length×150μm i.d.) were also prepared and coupled with the 37-cm-long×75-μm-i.d. octadecyl-functionalized monolithic column for two-dimensional SCX-RPLC-MS/MS analysis, which could identify 17114 unique peptides and 3211 unique proteins. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. A monolithically integrated torsional CMOS-MEMS relay

    Science.gov (United States)

    Riverola, M.; Sobreviela, G.; Torres, F.; Uranga, A.; Barniol, N.

    2016-11-01

    We report experimental demonstrations of a torsional microelectromechanical (MEM) relay fabricated using the CMOS-MEMS approach (or intra-CMOS) which exploits the full foundry inherent characteristics enabling drastic reduction of the fabrication costs and batch production. In particular, the relay is monolithically integrated in the back end of line of a commercial standard CMOS technology (AMS 0.35 μm) and released by means of a simple one-step mask-less wet etching. The fabricated torsional relay exhibits an extremely steep switching behaviour symmetrical about both contact sides with an on-state contact resistance in the k Ω -range throughout the on-off cycling test.

  15. Remote Sensing with Commutable Monolithic Laser and Detector

    Science.gov (United States)

    2016-01-01

    The ubiquitous trend toward miniaturized sensing systems demands novel concepts for compact and versatile spectroscopic tools. Conventional optical sensing setups include a light source, an analyte interaction region, and a separate external detector. We present a compact sensor providing room-temperature operation of monolithic surface-active lasers and detectors integrated on the same chip. The differentiation between emitter and detector is eliminated, which enables mutual commutation. Proof-of-principle gas measurements with a limit of detection below 400 ppm are demonstrated. This concept enables a crucial miniaturization of sensing devices. PMID:27785455

  16. Inherent polarization entanglement generated from a monolithic semiconductor chip

    DEFF Research Database (Denmark)

    Horn, Rolf T.; Kolenderski, Piotr; Kang, Dongpeng

    2013-01-01

    Creating miniature chip scale implementations of optical quantum information protocols is a dream for many in the quantum optics community. This is largely because of the promise of stability and scalability. Here we present a monolithically integratable chip architecture upon which is built...... a photonic device primitive called a Bragg reflection waveguide (BRW). Implemented in gallium arsenide, we show that, via the process of spontaneous parametric down conversion, the BRW is capable of directly producing polarization entangled photons without additional path difference compensation, spectral...... as a serious contender on which to build large scale implementations of optical quantum processing devices....

  17. A Monolithic Filter Cavity for Experiments in Quantum Optics

    CERN Document Server

    Palittapongarnpim, Pantita; Lvovsky, A I

    2012-01-01

    By applying a high-reflectivity dielectric coating on both sides of a commercial plano-convex lens, we produce a stable monolithic Fabry-Perot cavity suitable for use as a narrow band filter in quantum optics experiments. The resonant frequency is selected by means of thermal expansion. Owing to the long term mechanical stability, no optical locking techniques are required. We characterize the cavity performance as an optical filter, obtaining a 45 dB suppression of unwanted modes while maintaining a transmission of 60%.

  18. A novel carbon fiber based porous carbon monolith

    Energy Technology Data Exchange (ETDEWEB)

    Burchell, T.D.; Klett, J.W.; Weaver, C.E.

    1995-06-01

    A novel porous carbon material based on carbon fibers has been developed. The material, when activated, develops a significant micro- or mesopore volume dependent upon the carbon fiber type utilized (isotropic pitch or polyacrylonitrile). The materials will find applications in the field of fluid separations or as a catalyst support. Here, the manufacture and characterization of our porous carbon monoliths are described. A novel adsorbent carbon composite material has been developed comprising carbon fibers and a binder. The material, called carbon fiber composite molecular sieve (CFCMS), was developed through a joint research program between Oak Ridge National Laboratory (ORNL) and the University of Kentucky, Center for Applied Energy Research (UKCAER).

  19. Rapid Preparation of Monolithic Columns for Capillary Electrochromatography Separation

    Institute of Scientific and Technical Information of China (English)

    Wen Jun GONG; Yi Jun ZHANG; Yu Ping ZHANG; Seong Ho CHOI

    2006-01-01

    Fritless packed silica gel columns were prepared using sol-gel technology. The part of a75 μm i.d. capillary was filled with a mixture of methacryloxypropyltrimethoxysilane, toluene and hydrochloric acid. Four different photoinitiators such as benzoin methyl ether, Irgacure 819,Irgacure 1700 and irgacure 1800 were added in the presence or absence of sodium dodecyl sulfate during the polymerization process. The above eight solutions were irradiated at 365 nm about5-10 min to prepare the porous monolithic sol-gel columns by a one-step process.

  20. Hybrid and monolithic integration of planar lightwave circuits (PLCs)

    Science.gov (United States)

    Chen, Ray T.

    2008-02-01

    In this paper, we review the status of monolithic and hybrid integration of planar lightwave circuits (PLCs). Building blocks needed for system integration based on polymeric materials, III-V semiconductor materials, LiNbO 3 and SOI on Silicon are summarized with pros and cons. Due to the maturity of silicon CMOS technology, silicon becomes the platform of choice for optical application specific integrated circuits (OASICs). However, the indirect bandgap of silicon makes the formation of electrically pumped silicon laser a remote plausibility which requires hybrid integration of laser sources made out of III-V compound semicouductor.

  1. 1060-nm Tunable Monolithic High Index Contrast Subwavelength Grating VCSEL

    DEFF Research Database (Denmark)

    Ansbæk, Thor; Chung, Il-Sug; Semenova, Elizaveta

    2013-01-01

    We present the first tunable vertical-cavity surface-emitting laser (VCSEL) where the top distributed Bragg reflector has been completely substituted by an air-cladded high-index-contrast subwavelength grating (HCG) mirror. In this way, an extended cavity design can be realized by reducing...... the reflection at the semiconductor #x2013;air interface using an anti-reflective coating (ARC). We demonstrate how the ARC can be integrated in a monolithic structure by oxidizing AlGaAs with high Al-content. The HCG VCSEL has the potential to achieve polarization stable single-mode output with high tuning...

  2. Preparation of a biomimetic polyphosphorylcholine monolithic column for immobilized artificial membrane chromatography.

    Science.gov (United States)

    Zhao, XiangLong; Chen, WeiJia; Zhou, ZhengYin; Wang, QiQin; Liu, ZhengHua; Moaddel, Ruin; Jiang, ZhengJin

    2015-08-14

    The present work aims to prepare a novel phosphatidylcholine functionalized monolithic stationary phase by in situ co-polymerization of 12-methacryloyl dodecylphosphocholine (MDPC) and ethylene dimethacrylate (EDMA) for immobilized artificial membrane chromatography. Scanning electron microscopy, energy dispersive X-ray spectroscopy, FT-IR spectroscopy, pore size distribution analysis, ζ-potential analysis and micro-HPLC were used to evaluate the monolithic structure and physicochemical properties. Satisfactory morphology, high mechanical stability, good permeability and chromatographic performance were obtained on the optimized monolithic columns. A typical reverse-phase retention mechanism was observed over a wide range of organic solvent content (acetonitrilecolumn (IAM.PC.DD2) and poly(MDPC-co-EDMA) monolith. This novel poly(MDPC-co-EDMA) monolith exhibited good potential for studying the drug-membrane interaction.

  3. Synthesis and methane storage of binder-free porous graphene monoliths

    Institute of Scientific and Technical Information of China (English)

    Guoqing Ning; Hao Wang; Xiaoxin Zhang; Chenggen Xu; Guangjin Chen; Jinsen Gao

    2013-01-01

    Nanomesh graphene (NMG) obtained by template chemical vapor deposition was used to synthesize the binder-free graphene monoliths by simple tablet pressing.The stacking manner of the NMG sheets was crucial to the cohesion interaction between the graphene sheets,only the NMG materials with a loosely stacking manner could be pressed into binder-free monoliths.At the tableting pressure of 2-8 MPa,both the bulk densities and the specific surface areas of the monoliths keep nearly constant as the tableting pressure increases,indicating that the NMG monoliths have obvious elasticity and a porous structure due to the large corrugations and the mesh structures of the graphene sheets.As a result,an extraordinary methane storage capacity of 236 (v/v) at 9MPa was obtained in the graphene monolith prepared by tableting at 4 MPa.

  4. Monitoring catalysts at work in their final form: spectroscopic investigations on a monolithic catalyst

    DEFF Research Database (Denmark)

    Rasmussen, Søren B.; Bañares, Miguel A.; Bazin, Philippe;

    2012-01-01

    A monolithic vanadia–titania based catalyst has been subjected to studies with in situ FTIR spectroscopy coupled with mass spectrometry, during the SCR (Selective Catalytic Reduction) reaction. A device based on a transmission reactor cell for monolithic samples was constructed, dedicated to the ...... with other surface or bulk sensitive techniques, e.g. Raman and UV-vis spectroscopy.......A monolithic vanadia–titania based catalyst has been subjected to studies with in situ FTIR spectroscopy coupled with mass spectrometry, during the SCR (Selective Catalytic Reduction) reaction. A device based on a transmission reactor cell for monolithic samples was constructed, dedicated....... The observations reported here serve as a demonstration of the great potential for the application of operando spectroscopy on monolithic systems. This cross disciplinary approach aims to identify reaction pathways, active sites, intermediate- and spectator-species for catalytic reactions under truly industrial...

  5. Chelated minerals for poultry

    Directory of Open Access Journals (Sweden)

    SL Vieira

    2008-06-01

    Full Text Available Organic minerals have been subject of an increasing number of investigations recently. These compounds can be considered the most significant event regarding commercial forms of minerals targeting animal supplementation in the last decades. Minerals, especially metals, are usually supplemented in poultry feeds using cheap saline sources and have never required a lot of attention in terms of quality. On the other hand, definitions of organic minerals are very broad and frequently lead to confusion when decision-making becomes necessary. Organic minerals include any mineral bound to organic compounds, regardless of the type of existing bond between mineral and organic molecules. Proteins and carbohydrates are the most frequent candidates in organic mineral combinations. Organic fraction size and bond type are not limitations in organic mineral definition; however, essential metals (Cu, Fe, Zn, and Mn can form coordinated bonds, which are stable in intestinal lumen. Metals bound to organic ligands by coordinated bonds can dissociate within animal metabolism whereas real covalent bonds cannot. Chelated minerals are molecules that have a metal bound to an organic ligand through coordinated bonds; but many organic minerals are not chelates or are not even bound through coordinated bonds. Utilization of organic minerals is largely dependent on the ligand; therefore, amino acids and other small molecules with facilitated access to the enterocyte are supposed to be better utilized by animals. Organic minerals with ligands presenting long chains may require digestion prior to absorption. After absorption, organic minerals may present physiological effects, which improve specific metabolic responses, such as the immune response. Many studies have demonstrated the benefits of metal-amino acid chelates on animal metabolism, but the detection positive effects on live performance is less consistent.

  6. New 3-D microarray platform based on macroporous polymer monoliths.

    Science.gov (United States)

    Rober, M; Walter, J; Vlakh, E; Stahl, F; Kasper, C; Tennikova, T

    2009-06-30

    Polymer macroporous monoliths are widely used as efficient sorbents in different, mostly dynamic, interphase processes. In this paper, monolithic materials strongly bound to the inert glass surface are suggested as operative matrices at the development of three-dimensional (3-D) microarrays. For this purpose, several rigid macroporous copolymers differed by reactivity and hydrophobic-hydrophilic properties were synthesized and tested: (1) glycidyl methacrylate-co-ethylene dimethacrylate (poly(GMA-co-EDMA)), (2) glycidyl methacrylate-co-glycerol dimethacrylate (poly(GMA-co-GDMA)), (3) N-hydroxyphthalimide ester of acrylic acid-co-glycidyl methacrylate-co-ethylene dimethacrylate (poly(HPIEAA-co-GMA-co-EDMA)), (4) 2-cyanoethyl methacrylate-co-ethylene dimethacrylate (poly(CEMA-co-EDMA)), and (5) 2-cyanoethyl methacrylate-co-2-hydroxyethyl methacrylate-co-ethylene dimethacrylate (poly(CEMA-co-HEMA-co-EDMA)). The constructed devices were used as platforms for protein microarrays construction and model mouse IgG-goat anti-mouse IgG affinity pair was used to demonstrate the potential of developed test-systems, as well as to optimize microanalytical conditions. The offered microarray platforms were applied to detect the bone tissue marker osteopontin directly in cell culture medium.

  7. Methacrylate-based monolithic layers for planar chromatography of polymers.

    Science.gov (United States)

    Maksimova, E F; Vlakh, E G; Tennikova, T B

    2011-04-29

    A series of macroporous monolithic methacrylate-based materials was synthesized by in situ free radical UV-initiated copolymerization of functional monomers, such as glycidyl methacrylate (GMA), butyl methacrylate (BuMA), 2-aminoethyl methacrylate (AEMA), 2-hydroxyethyl methacrylate (HEMA) and 2-cyanoethyl methacrylate (CEMA), with crosslinking agent, namely, ethylene glycol dimethacrylate (EDMA). The materials obtained were applied as the stationary phases in simple and robust technique - planar chromatography (PLC). The method of separation layer fabrication representing macroporous polymer monolith bound to the specially prepared glass surface was developed and optimized. The GMA-EDMA and BuMA-EDMA matrixes were successfully applied for the separation of low molecular weight compounds (the mixture of several dies), as well as poly(vinylpyrrolidone) and polystyrene homopolymers of different molecular weights using reversed-phase mechanism. The materials based on copolymers AEMA-HEMA-EDMA and CEMA-HEMA-EDMA were used for normal-phase PLC separation of 2,4-dinitrophenyl amino acids and polystyrene standards.

  8. Squeezed light from a diamond-turned monolithic cavity

    CERN Document Server

    Brieussel, A; Campbell, G; Guccione, G; Janousek, J; Hage, B; Buchler, B C; Treps, N; Fabre, C; Fang, F Z; Li, X Y; Symul, T; Lam, P K

    2016-01-01

    For some crystalline materials, a regime can be found where continuous ductile cutting is feasible. Using precision diamond turning, such materials can be cut into complex optical components with high surface quality and form accuracy. In this work we use diamond-turning to machine a monolithic, square-shaped, doubly-resonant $LiNbO_3$ cavity with two flat and two convex facets. When additional mild polishing is implemented, the Q-factor of the resonator is found to be limited only by the material absorption loss. We show how our monolithic square resonator may be operated as an optical parametric oscillator that is evanescently coupled to free-space beams via birefringent prisms. The prism arrangement allows for independent and large tuning of the fundamental and second harmonic coupling rates. We measure $2.6\\pm0.5$ dB of vacuum squeezing at 1064 nm using our system. Potential improvements to obtain higher degrees of squeezing are discussed.

  9. Fabrication of Monolithic RERTR Fuels by Hot Isostatic Pressing

    Energy Technology Data Exchange (ETDEWEB)

    Jan-Fong Jue; Blair H. Park; Curtis R. Clark; Glenn A. Moore; Dennis D. Keiser, Jr.

    2010-11-01

    The RERTR (Reduced Enrichment for Research and Test Reactors) Program is developing advanced nuclear fuels for high-power test reactors. Monolithic fuel design provides higher uranium loading than that of the traditional dispersion fuel design. Hot isostatic pressing is a promising process for low-cost batch fabrication of monolithic RERTR fuel plates for these high-power reactors. Bonding U Mo fuel foil and 6061 Al cladding by hot isostatic press bonding was successfully developed at Idaho National Laboratory. Due to the relatively high processing temperature, the interaction between fuel meat and aluminum cladding is a concern. Two different methods were employed to mitigate this effect: (1) a diffusion barrier and (2) a doping addition to the interface. Both types of fuel plates have been fabricated by hot isostatic press bonding. Preliminary results show that the direct fuel/cladding interaction during the bonding process was eliminated by introducing a thin zirconium diffusion barrier layer between the fuel and the cladding. Fuel plates were also produced and characterized with a silicon-rich interlayer between fuel and cladding. This paper reports the recent progress of this developmental effort and identifies the areas that need further attention.

  10. Macroporous monoliths for trace metal extraction from seawater

    Energy Technology Data Exchange (ETDEWEB)

    Yue, Yanfeng; Mayes, Richard; Gill, Gary A.; Kuo, Li-Jung; Wood, Jordana R.; Binder, Andrew; Brown, Suree; Dai, Sheng

    2015-05-29

    The viability of seawater-based uranium recovery depends on the uranium adsorption rate and capacity, since the concentration of uranium in the oceans is relatively low (3.3 μgL⁻¹). An important consideration for a fast adsorption is to maximize the adsorption properties of adsorbents such as surface areas and pore structures, which can greatly improve the kinetics of uranium extraction and the adsorption capacity simultaneously. Following this consideration, macroporous monolith adsorbents were prepared from the copolymerization of acrylonitrile (AN) and N,N’-methylenebis(acrylamide) (MBAAm) based on a cryogel method using both hydrophobic and hydrophilic monomers. The monolithic sorbents were tested with simulated seawater containing a high uranyl concentration (–6 ppm) and the uranium adsorption results showed that the adsorption capacities are strongly influenced by the ratio of monomer to the crosslinker, i.e., the density of the amidoxime groups. The preliminary seawater testing indicates the high salinity content of seawater does not hinder the adsorption of uranium.

  11. Monolithically Integrated Ge-on-Si Active Photonics

    Directory of Open Access Journals (Sweden)

    Jifeng Liu

    2014-07-01

    Full Text Available Monolithically integrated, active photonic devices on Si are key components in Si-based large-scale electronic-photonic integration for future generations of high-performance, low-power computation and communication systems. Ge has become an interesting candidate for active photonic devices in Si photonics due to its pseudo-direct gap behavior and compatibility with Si complementary metal oxide semiconductor (CMOS processing. In this paper, we present a review of the recent progress in Ge-on-Si active photonics materials and devices for photon detection, modulation, and generation. We first discuss the band engineering of Ge using tensile strain, n-type doping, Sn alloying, and separate confinement of Γ vs. L electrons in quantum well (QW structures to transform the material towards a direct band gap semiconductor for enhancing optoelectronic properties. We then give a brief overview of epitaxial Ge-on-Si materials growth, followed by a summary of recent investigations towards low-temperature, direct growth of high crystallinity Ge and GeSn alloys on dielectric layers for 3D photonic integration. Finally, we review the most recent studies on waveguide-integrated Ge-on-Si photodetectors (PDs, electroabsorption modulators (EAMs, and laser diodes (LDs, and suggest possible future research directions for large-scale monolithic electronic-photonic integrated circuits on a Si platform.

  12. Monolithic integrated optic fiber Bragg grating sensor interrogator

    Science.gov (United States)

    Mendoza, Edgar A.; Esterkin, Yan; Kempen, Cornelia; Sun, Songjian

    2010-04-01

    Fiber Bragg gratings (FBGs) are a mature sensing technology that has gained rapid acceptance in civil, aerospace, chemical and petrochemical, medicine, aviation and automotive industries. Fiber Bragg grating sensors can be use for a variety of measurements including strain, stress, vibration, acoustics, acceleration, pressure, temperature, moisture, and corrosion distributed at multiple locations within the structure using a single fiber element. The most prominent advantages of FBGs are: small size and light weight, multiple FBG transducers on a single fiber, and immunity to radio frequency interference. A major disadvantage of FBG technology is that conventional state-of-the-art fiber Bragg grating interrogation systems are typically bulky, heavy, and costly bench top instruments that are assembled from off-the-shelf fiber optic and optical components integrated with a signal electronics board into an instrument console. Based on the need for a compact FBG interrogation system, this paper describes recent progress towards the development of a miniature fiber Bragg grating sensor interrogator (FBG-TransceiverTM) system based on multi-channel monolithic integrated optic sensor microchip technology. The integrated optic microchip technology enables the monolithic integration of all of the functionalities, both passive and active, of conventional bench top FBG sensor interrogators systems, packaged in a miniaturized, low power operation, 2-cm x 5-cm small form factor (SFF) package suitable for the long-term structural health monitoring in applications where size, weight, and power are critical for operation.

  13. Monolithic molecularly imprinted polymeric capillary columns for isolation of aflatoxins.

    Science.gov (United States)

    Szumski, Michał; Grzywiński, Damian; Prus, Wojciech; Buszewski, Bogusław

    2014-10-17

    Monolithic molecularly imprinted polymers extraction columns have been prepared in fused-silica capillaries by UV or thermal polymerization in a two-step process. First, a poly-(trimethylolpropane trimethacrylate) (polyTRIM) core monolith was synthesized either by UV or thermal polymerization. Then it was grafted with the mixture of methacrylic acid (MAA) as a functional monomer, ethylene dimethacrylate (EDMA) as a cross-linking agent, 5,7-dimethoxycoumarin (DMC) as an aflatoxin-mimicking template, toluene as a porogen solvent and 2,2-azobis-(2-methylpropionitrile) (AIBN) as an initiator of the polymerization reaction. Different thermal condition of the photografting and different concentrations of the grafting mixture were tested during polymerization. The extraction capillary columns were evaluated in the terms of their hydrodynamic and chromatographic properties. Retention coefficients for aflatoxin B1 and DMC were used for assessment of the selectivity and imprinting factor. The obtained results indicate that the temperature of photografting and concentration of the grafting mixture are key parameters that determine the quality of the prepared MIPs. From the MIP columns characterized by the highest permeability the column of the highest imprinting factor was applied for isolation of aflatoxins B1, B2, G1 and G2 from the model aqueous sample followed by on-line chromatographic separation. The process was performed using a micro-MISPE-microLC-LIF system of a novel design, which allowed for detection of the eluates from the sample preparation part as well as from the chromatographic separation.

  14. Nitrogen and Phosphorous Co-Doped Graphene Monolith for Supercapacitors.

    Science.gov (United States)

    Wen, Yangyang; Rufford, Thomas E; Hulicova-Jurcakova, Denisa; Wang, Lianzhou

    2016-03-08

    The co-doping of heteroatoms has been regarded as a promising approach to improve the energy-storage performance of graphene-based materials because of the synergetic effect of the heteroatom dopants. In this work, a single precursor melamine phosphate was used for the first time to synthesise nitrogen/phosphorus co-doped graphene (N/P-G) monoliths by a facile hydrothermal method. The nitrogen contents of 4.27-6.58 at% and phosphorus levels of 1.03-3.00 at% could be controlled by tuning the mass ratio of melamine phosphate to graphene oxide in the precursors. The N/P-G monoliths exhibited excellent electrochemical performances as electrodes for supercapacitors with a high specific capacitance of 183 F g(-1) at a current density of 0.05 A g(-1), good rate performance and excellent cycling performance. Additionally, the N/P-G electrode was stable at 1.6 V in 1 m H2 SO4 aqueous electrolyte and delivered a high energy density of 11.33 Wh kg(-1) at 1.6 V. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Monolithically integrated Helmholtz coils by 3-dimensional printing

    Energy Technology Data Exchange (ETDEWEB)

    Li, Longguang [Department of Electrical Engineering, University of Michigan–Shanghai Jiao Tong University Joint Institute, Shanghai Jiao Tong University, Shanghai 200240 (China); Abedini-Nassab, Roozbeh; Yellen, Benjamin B., E-mail: yellen@duke.edu [Department of Electrical Engineering, University of Michigan–Shanghai Jiao Tong University Joint Institute, Shanghai Jiao Tong University, Shanghai 200240 (China); Department of Mechanical Engineering and Materials Science, Duke University, P.O. Box 90300, Hudson Hall, Durham, North Carolina 27708 (United States)

    2014-06-23

    3D printing technology is of great interest for the monolithic fabrication of integrated systems; however, it is a challenge to introduce metallic components into 3D printed molds to enable broader device functionality. Here, we develop a technique for constructing a multi-axial Helmholtz coil by injecting a eutectic liquid metal Gallium Indium alloy (EGaIn) into helically shaped orthogonal cavities constructed in a 3D printed block. The tri-axial solenoids each carry up to 3.6 A of electrical current and produce magnetic field up to 70 G. Within the central section of the coil, the field variation is less than 1% and is in agreement with theory. The flow rates and critical pressures required to fill the 3D cavities with liquid metal also agree with theoretical predictions and provide scaling trends for filling the 3D printed parts. These monolithically integrated solenoids may find future applications in electronic cell culture platforms, atomic traps, and miniaturized chemical analysis systems based on nuclear magnetic resonance.

  16. Monolithic Active Pixel Matrix with Binary Counters (MAMBO) ASIC

    Energy Technology Data Exchange (ETDEWEB)

    Khalid, Farah F.; Deptuch, Grzegorz; Shenai, Alpana; Yarema, Raymond J.; /Fermilab

    2010-11-01

    Monolithic Active Matrix with Binary Counters (MAMBO) is a counting ASIC designed for detecting and measuring low energy X-rays from 6-12 keV. Each pixel contains analogue functionality implemented with a charge preamplifier, CR-RC{sup 2} shaper and a baseline restorer. It also contains a window comparator which can be trimmed by 4 bit DACs to remove systematic offsets. The hits are registered by a 12 bit ripple counter which is reconfigured as a shift register to serially output the data from the entire ASIC. Each pixel can be tested individually. Two diverse approaches have been used to prevent coupling between the detector and electronics in MAMBO III and MAMBO IV. MAMBO III is a 3D ASIC, the bottom ASIC consists of diodes which are connected to the top ASIC using {mu}-bump bonds. The detector is decoupled from the electronics by physically separating them on two tiers and using several metal layers as a shield. MAMBO IV is a monolithic structure which uses a nested well approach to isolate the detector from the electronics. The ASICs are being fabricated using the SOI 0.2 {micro}m OKI process, MAMBO III is 3D bonded at T-Micro and MAMBO IV nested well structure was developed in collaboration between OKI and Fermilab.

  17. Monolithic crystals for PET devices: Optical coupling optimization

    Energy Technology Data Exchange (ETDEWEB)

    González, A.J., E-mail: agonzalez@i3m.upv.es; Peiró, A.; Conde, P.; Hernández, L.; Moliner, L.; Orero, A.; Rodríguez-Álvarez, M.J.; Sánchez, F.; Soriano, A.; Vidal, L.F.; Benlloch, J.M.

    2013-12-11

    In this work we present a method to efficiently collect scintillation light when using monolithic scintillator crystals. The acceptance angle of the scintillation light has been reduced by means of optical devices reducing the border effect which typically affects continuous crystals. We have applied this procedure on gamma detectors for PET systems using both position sensitive PMTs and arrays of SiPMs. In the case of using SiPMs, this approach also helps to reduce the photosensor active area. We evaluated the method using PMTs with a variety of different crystals with thicknesses ranging from 10 to 24 mm. We found that our design allows the use of crystal blocks with a thickness of up to 18 mm without degrading the spatial resolution caused by edge effects and without a significant detriment to the energy resolution. These results were compared with simulated data. The first results of monolithic LYSO crystals coupled to an array of 256 SiPMs by means of individual optical light guides are also presented. -- Highlights: •Acceptance angle reduction decreases border effect in continuous crystals. •Experimental measurements with PMTs correlate well with simulated data. •Optical devices called faceplates serve to control the scintillation light angle. •Simulation on the light propagation for SiPMs requires exhaustive modeling.

  18. 43 CFR 19.8 - Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

    Science.gov (United States)

    2010-10-01

    ... patents, and mineral leasing within National Forest Wilderness. 19.8 Section 19.8 Public Lands: Interior... § 19.8 Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest... locations, mineral patents, and mineral leasing within National Forest Wilderness are contained in parts...

  19. Synthesis and characterization of hierarchically porous metal, metal oxide, and carbon monoliths with highly ordered nanostructure

    Science.gov (United States)

    Grano, Amy Janine

    Hierarchically porous materials are of great interest in such applications as catalysis, separations, fuel cells, and advanced batteries. One such way of producing these materials is through the process of nanocasting, in which a sacrificial template is replicated and then removed to form a monolithic replica. This replica consists of mesopores, which can be ordered or disordered, and bicontinuous macropores, which allow flow throughout the length of the monolith. Hierarchically porous metal oxide and carbon monoliths with an ordered mesopores system are synthesized for the first time via nanocasting. These replicas were used as supports for the deposition of silver particles and the catalytic efficiency was evaluated. The ordered silica template used in producing these monoliths was also used for an in-situ TEM study involving metal nanocasting, and an observation of the destruction of the silica template during nanocasting made. Two new methods of removing the silica template were developed and applied to the synthesis of copper, nickel oxide, and zinc oxide monoliths. Finally, hollow fiber membrane monoliths were examined via x-ray tomography in an attempt to establish the presence of this structure throughout the monolith.

  20. Monolithic column incorporated with lanthanide metal-organic framework for capillary electrochromatography.

    Science.gov (United States)

    Zhang, Li-Shun; Du, Pei-Yao; Gu, Wen; Zhao, Qing-Li; Huang, Yan-Ping; Liu, Zhao-Sheng

    2016-08-26

    A new lanthanide metal-organic frameworks NKU-1 have successfully incorporated into poly (BMA-co-EDMA) monolith and evaluated by capillary electrochromatography (CEC). Lanthanide metal-organic frameworks [Eu2(ABTC)1.5(H2O)3(DMA)] (NKU-1) were synthesized by self-assembly of Eu(III) ions and 3,3',5,5'-azo benzene tetracarboxylic acid ligands have been fabricated into poly(BMA-co-EDMA) monoliths. 1-Butyl-3-methylimidazolium tetrafluoroborate and N,N-dimethylformamide were developed as binary porogen obtaining homogeneous dispersibility for NKU-1 and high permeability for monolithic column. The successful incorporation of NKU-1 into poly(BMA-co-EDMA) was confirmed and characterized by FT-IR spectra, scanning electron microscopy, X-ray diffraction, energy dispersive spectrometer area scanning, and transmission electron microscopy. Separation ability of the NKU-1-poly (BMA-co-EDMA) monoliths was demonstrated by separating four groups of analytes in CEC, including alkylbenzenes, polycyclic aromatic hydrocarbon, aniline series and naphthyl substitutes. Compared with bare monolithic (column efficiency of 100,000plates/m), the NKU-1-poly (BMA-co-EDMA) monoliths have displayed greater column efficiency (maximum 210,000plates/m) and higher permeability, as well as less peak tailing. The results showed that the NKU-1-poly (BMA-co-EDMA) monoliths are promising stationary phases for CEC separations.

  1. Wideband monolithically integrated front-end subsystems and components

    Science.gov (United States)

    Mruk, Joseph Rene

    This thesis presents the analysis, design, and measurements of passive, monolithically integrated, wideband recta-coax and printed circuit board front-end components. Monolithic fabrication of antennas, impedance transformers, filters, and transitions lowers manufacturing costs by reducing assembly time and enhances performance by removing connectors and cabling between the devices. Computational design, fabrication, and measurements are used to demonstrate the capabilities of these front-end assemblies. Two-arm wideband planar log-periodic antennas fed using a horizontal feed that allows for filters and impedance transformers to be readily fabricated within the radiating region of the antenna are demonstrated. At microwave frequencies, low-cost printed circuit board processes are typically used to produce planar devices. A 1.8 to 11 GHz two-arm planar log-periodic antenna is designed with a monolithically integrated impedance transformer. Band rejection methods based on modifying the antenna aperture, use of an integrated filter, and the application of both methods are investigated with realized gain suppressions of over 25 dB achieved. The ability of standard circuit board technology to fabricate millimeter-wave devices up to 110 GHz is severely limited. Thin dielectrics are required to prevent the excitation of higher order modes in the microstrip substrate. Fabricating the thin line widths required for the antenna aperture also becomes prohibitively challenging. Surface micro-machining typically used in the fabrication of MEMS devices is capable of producing the extremely small features that can be used to fabricate antennas extending through W-band. A directly RF fed 18 to 110 GHz planar log-periodic antenna is developed. The antenna is fabricated with an integrated impedance transformer and additional transitions for measurement characterization. Singly terminated low-loss wideband millimeter-wave filters operating over V- and W- band are developed. High

  2. Monolitni katalizatori i reaktori: osnovne značajke, priprava i primjena (Monolith catalysts and reactors: preparation and applications

    Directory of Open Access Journals (Sweden)

    Tomašić, V.

    2004-12-01

    Full Text Available Monolithic (honeycomb catalysts are continuous unitary structures containing many narrow, parallel and usually straight channels (or passages. Catalytically active components are dispersed uniformly over the whole porous ceramic monolith structure (so-called incorporated monolithic catalysts or are in a layer of porous material that is deposited on the walls of channels in the monolith's structure (washcoated monolithic catalysts. The material of the main monolithic construction is not limited to ceramics but includes metals, as well. Monolithic catalysts are commonly used in gas phase catalytic processes, such as treatment of automotive exhaust gases, selective catalytic reduction of nitrogen oxides, catalytic removal of volatile organic compounds from industrial processes, etc. Monoliths continue to be the preferred support for environmental applications due to their high geometric surface area, different design options, low pressure drop, high temperature durability, mechanical strength, ease of orientation in a reactor and effectiveness as a support for a catalytic washcoat. As known, monolithic catalysts belong to the class of the structured catalysts and/or reactors (in some cases the distinction between "catalyst" and "reactor" has vanished. Structured catalysts can greatly intensify chemical processes, resulting in smaller, safer, cleaner and more energy efficient technologies. Monolith reactors can be considered as multifunctional reactors, in which chemical conversion is advantageously integrated with another unit operation, such as separation, heat exchange, a secondary reaction, etc. Finally, structured catalysts and/or reactors appear to be one of the most significant and promising developments in the field of heterogeneous catalysis and chemical engineering of the recent years. This paper gives a description of the background and perspectives for application and development of monolithic materials. Different methods and techniques

  3. Conversion of methanol to gasoline-range hydrocarbons in a ZSM-5 coated monolithic reactor

    Energy Technology Data Exchange (ETDEWEB)

    Antia, J.E.; Govind, R. (Univ. of Cincinnati, OH (United States). Dept. of Chemical Engineering)

    1995-01-01

    Novel reactor configurations featuring catalysts supported on monolithic or honeycomb structures are being increasingly used for a number of applications. In this work, a zeolite-coated monolithic reactor is employed for the conversion of methanol to gasoline-range hydrocarbons. Experimental results show that the conversion and hydrocarbon product distribution compare favorably with data reported for fixed and fluid beds. Mathematical modeling shows that the conversion here is controlled by diffusion in the molecule-sized intracrystalline pores of the zeolite structure. This finding is of considerable important because it demonstrates that monolithic reactors are well-suited to zeolite-based catalytic processes.

  4. Recent Accomplishments in the Irradiation Testing of Engineering-Scale Monolithic Fuel Specimens

    Energy Technology Data Exchange (ETDEWEB)

    N.E. Woolstenhulme; D.M. Wachs; M.K. Meyer; H.W. Glunz; R.B. Nielson

    2012-10-01

    The US fuel development team is focused on qualification and demonstration of the uranium-molybdenum monolithic fuel including irradiation testing of engineering-scale specimens. The team has recently accomplished the successful irradiation of the first monolithic multi-plate fuel element assembly within the AFIP-7 campaign. The AFIP-6 MKII campaign, while somewhat truncated by hardware challenges, exhibited successful irradiation of a large-scale monolithic specimen under extreme irradiation conditions. The channel gap and ultrasonic data are presented for AFIP-7 and AFIP-6 MKII, respectively. Finally, design concepts are summarized for future irradiations such as the base fuel demonstration and design demonstration experiment campaigns.

  5. Data in support of preparation and functionalization of a clickable polycarbonate monolith

    Directory of Open Access Journals (Sweden)

    Yuanrong Xin

    2016-06-01

    Full Text Available This data article provides supplementary figures to the research article entitled, “Phase separation approach to a reactive polycarbonate monolith for “click” modifications” (Xin et al., Polymer, 2015, doi:10.1016/j.polymer.2015.04.008. Here, the nitrogen adsorption/desorption isotherms of the prepared porous polycarbonate monolith are shown to classify its inner structure and calculate the specific surface area. The monoliths were modified by using the thiol-ene click chemistry and the olefin metathesis, which was examined by contact angle measurements, FT-IR, solid state 13C NMR spectroscopy as well as thermogravimetric analysis.

  6. Stanley Kubrick and B.F. Skinner : Is a Teaching Machine a Monolith ?

    OpenAIRE

    浜野, 保樹; ハマノ, ヤスキ; Yasuki, Hamano

    1990-01-01

    The teaching machine invented by B.F. Skinner was recog-nized as one of few clear achievements of scientific pedagogy and even appeared in SF. Arthur C. Clarke who wrote the script of the SF movie "2001: A Space Odyssey" with Stanley Kubrick wanted to scientifically define a monolith to be a God who had given intelligence to our ancestors. In other words, he wanted to describe a monolith as a teaching machine as well as a God. However Kubrick did not want to make clear about what a monolith i...

  7. Failure analysis of various monolithic posterior aesthetic dental crowns using finite element method

    Science.gov (United States)

    Porojan, Liliana; Topală, Florin

    2017-08-01

    The aim of the study was to assess the effect of material stiffness and load on the biomechanical performance of the monolithic full-coverage posterior aesthetic dental crowns using finite element analysis. Three restorative materials for monolithic dental crowns were selected for the study: zirconia; lithium disilicate glass-ceramic, and resin-based composite. Stresses were calculated in the crowns for all materials and in the teeth structures, under different load values. The experiments show that dental crowns made from all this new aesthetic materials processed by CAD/CAM technologies would be indicated as monolithic dental crowns for posterior areas.

  8. SELF-CONSOLIDATING CONCRETE USED IN THE MONOLITHIC CONSTRUCTION OF EARTHQUAKE-RESISTANT TALL BUILDING

    Directory of Open Access Journals (Sweden)

    S. A. Aliev

    2016-01-01

    Full Text Available Objectives. The development of high-strength concrete based on experience both with domestic and foreign concretes has led to the production of a self-consolidating concrete (SCC formula. Method. Raw materials sourced from the Chechen Republic were used in the SUBconcrete formula, based on materials having different classes of compressive strength as well as the incorporation of polycarboxylate as an additive. Results. An investigation was carried out on natural and technogenic raw materials from the Chechen Republic and other regions of the country. Compositions of high-grade SCC with a compressive strength of B100 and higher are achieved with an integrated approach using both natural and man-made raw materials. The formulae of the basic concrete reinforcing technology are examined together with their physico-mechanical properties. The results of the study of locally sourced concrete, as well as that purchased from "Pavlovskgranit" and OOO "Progress" for testing from the Republic of North Ossetia–Alania, are provided. Of the various manufacturers' cements investigated, the highest quality Portland cement CEM I 4.5N was selected from the Tula cement manufacturers in the town of Chiri-Yurt. The fillers used were microsilica sourced from the Novokuznetsk plant, inactivated MP-1 mineral powder produced in Kaluga and fly ash sourced from Nevinnomyssk. Conclusion. The results of the studies show that the raw material potential of our country allows for the production of self-consolidating concrete from class B 25 to B100 and higher for use in monolithic construction, including high-rise. The concrete compositions arrived at are characterised by their high physical and mechanical properties and can be used in high-rise concrete construction sites operating in earthquake-prone areas. 

  9. Monolithic active pixel radiation detector with shielding techniques

    Energy Technology Data Exchange (ETDEWEB)

    Deptuch, Grzegorz W.

    2016-09-06

    A monolithic active pixel radiation detector including a method of fabricating thereof. The disclosed radiation detector can include a substrate comprising a silicon layer upon which electronics are configured. A plurality of channels can be formed on the silicon layer, wherein the plurality of channels are connected to sources of signals located in a bulk part of the substrate, and wherein the signals flow through electrically conducting vias established in an isolation oxide on the substrate. One or more nested wells can be configured from the substrate, wherein the nested wells assist in collecting charge carriers released in interaction with radiation and wherein the nested wells further separate the electronics from the sensing portion of the detector substrate. The detector can also be configured according to a thick SOA method of fabrication.

  10. Monolithic silica aerogel - material design on the nano-scale

    DEFF Research Database (Denmark)

    Jensen, Karsten Ingerslev; Schultz, Jørgen Munthe; Kristiansen, Finn Harken

    By means of a production process in two major steps - a sol/gel process and a supercritical drying – open-cell, monolithic silica aerogel can be made. This material can have a density in the range of 30- to 300 kg/m3, corresponding to porosities between 86 and 98 %. The solid structure has...... of piezoelectric transducers. - Other applications could be; waste encapsulation, spacers for vacuum insulation panels, membranes, etc. Department of Civil Engineering is co-ordinator of a current EU FP5 research project1, which deals with the application of aerogel as transparent insulation materials in windows....... Due to the excellent optical and thermal properties of aerogel, it is possible to develop windows with both high insulation and high transmittance, which is impossible applying the conventional window techniques, i.e. extra layers of glass, low-e coatings and gas fillings. It can be shown...

  11. Highly tailorable thiol-ene based emulsion-templated monoliths

    DEFF Research Database (Denmark)

    Lafleur, J. P.; Kutter, J. P.

    2014-01-01

    The attractive surface properties of thiol-ene polymers combined with their ease of processing make them ideal substrates in many bioanalytical applications. We report the synthesis of highly tailorable emulsion-templated porous polymers and beads in microfluidic devices based on off-stoichiometr......The attractive surface properties of thiol-ene polymers combined with their ease of processing make them ideal substrates in many bioanalytical applications. We report the synthesis of highly tailorable emulsion-templated porous polymers and beads in microfluidic devices based on off......-stoichiometry thiolene chemistry. The method allows monolith synthesis and anchoring inside thiol-ene microchannels in a single step. Variations in the monomer stoichiometric ratios and/or amount of porogen used allow for the creation of extremely varied polymer morphologies, from foam-like materials to dense networks...

  12. Monolithic growth of partly cured polydimethylsiloxane thin film layers

    DEFF Research Database (Denmark)

    Yu, Liyun; Skov, Anne Ladegaard

    2014-01-01

    The demand for monolithic structures in many applications has increased to enable more reliable and optimized performances such as for dielectric electroactive polymers (DEAPs). For the layers of the elements to grow efficiently together, it is first of all required that the layers adhere together...... as thermal stabilities of the bilayer elastomer films are observed to change with the curing time of the monolayers before lamination. The objective of this work is to create adhesion of two layers without destroying the original viscoelastic properties of the PDMS films, and hence enable, for example......, adhesion of two microstructured films which is currently a crucial step in the large-scale production of DEAPs. © 2014 The Society of Polymer Science, Japan (SPSJ) All rights reserved....

  13. Material Engineering for Monolithic Semiconductor Mode-Locked Lasers

    DEFF Research Database (Denmark)

    Kulkova, Irina

    This thesis is devoted to the materials engineering for semiconductor monolithic passively mode-locked lasers (MLLs) as a compact energy-efficient source of ultrashort optical pulses. Up to the present day, the achievement of low-noise sub-picosecond pulse generation has remained a challenge....... This work has considered the role of the combined ultrafast gain and absorption dynamics in MLLs as a main factor limiting laser performance. An independent optimization of MLL amplifier and saturable absorber active materials was performed. Two promising approaches were considered: quantum dot (QD...... application in MLLs. Improved QW laser performance was demonstrated using the asymmetric barrier layer approach. The analysis of the gain characteristics showed that the high population inversion beneficial for noise reduction cannot be achieved for 10 GHz QW MLLs and would have required lowering the modal...

  14. Development of highly sensitive monolithic interferometer for infrared planet search

    Directory of Open Access Journals (Sweden)

    Jiang P.

    2011-07-01

    Full Text Available We present the design, fabrication and testing of a highly sensitive monolithic interferometer for InfraRed Exoplanet Tracker (IR-ET. This interferometer is field-compensated, thermal-stable for working in the wavelength range between 0.8 and 1.35 μm. Two arms of the interferometer creates a fixed delay of 18.0 mm, which is optimized to have the best sensitivity for radial velocity measurements of slow-rotating M dwarfs for planet detection. IR-ET is aiming to reach 3–20 m/s Doppler precision for J<10 M dwarfs in less than 15 min exposures. We plan to conduct a planet survey around hundreds of nearby M dwarfs through collaborations with Astrophysical Research Consortium scientists in 2011–2014.

  15. Design of ultra-lightweight concrete: towards monolithic concrete structures

    Directory of Open Access Journals (Sweden)

    Yu Qing Liang

    2014-04-01

    Full Text Available This study addresses the development of ultra-lightweight concrete. A moderate strength and an excellent thermal conductivity of the lightweight concrete are set as the design targets. The designed lightweight aggregates concrete is targeted to be used in monolithic concrete façade structure, performing as both load bearing element and thermal insulator. The developed lightweight concrete shows excellent thermal properties, with a low thermal conductivity of about 0.12 W/(m·K; and moderate mechanical properties, with 28-day compressive strengths of about 10-12 N/mm . This combination of values exceeds, to the researchers’ knowledge, the performance of all other lightweight building materials. Furthermore, the developed lightweight concrete possesses excellent durability properties.

  16. An Energy Preserving Monolithic Eulerian Fluid-Structure Numerical Scheme

    CERN Document Server

    Pironneau, Olivier

    2016-01-01

    The conservation laws of continuum mechanic written in an Eulerian frame make no difference between fluids and solids except in the expression of the stress tensors, usually with Newton's hypothesis for the fluids and Helmholtz potentials of energy for hyperelastic solids. By taking the velocities as unknown , monolithic methods for fluid structure interactions (FSI) are built. In this article such a formulation is analyzed when the fluid is compressible and the fluid is incompressible. The idea is not new but the progress of mesh generators and numerical schemes like the Characteristics-Galerkin method render this approach feasible and reasonably robust. In this article the method and its discretization are presented, stability is discussed by through an energy estimate. A numerical section discusses implementation issues and presents a few simple tests.

  17. A monolithic time stretcher for precision time recording

    Energy Technology Data Exchange (ETDEWEB)

    Varner, Gary S.

    2007-04-20

    Identifying light mesons which contain only up/down quarks (pions) from those containing a strange quark (kaons) over the typical meter length scales of a particle physics detector requires instrumentation capable of measuring flight times with a resolution on the order of 20ps. In the last few years a large number of inexpensive, multi-channel Time-to-Digital Converter (TDC) chips have become available. These devices typically have timing resolution performance in the hundreds of ps regime. A technique is presented that is a monolithic version of ``time stretcher'' solution adopted for the Belle Time-Of-Flight system to address this gap between resolution need and intrinsic multi-hit TDC performance.

  18. Monolithic interconnected modules (MIMs) for thermophotovoltaic energy conversion

    Science.gov (United States)

    Wilt, David; Wehrer, Rebecca; Palmisiano, Marc; Wanlass, Mark; Murray, Christopher

    2003-05-01

    Monolithic interconnected modules (MIMs) are under development for thermophotovoltaic (TPV) energy conversion applications. MIM devices are typified by series-interconnected photovoltaic cells on a common, semi-insulating substrate and generally include rear-surface infrared (IR) reflectors. The MIM architecture is being implemented in InGaAsSb materials without semi-insulating substrates through the development of alternative isolation methodologies. Motivations for developing the MIM structure include: reduced resistive losses, higher output power density than for systems utilizing front surface spectral control, improved thermal coupling and ultimately higher system efficiency. Numerous design and material changes have been investigated since the introduction of the MIM concept in 1994. These developments as well as the current design strategies are addressed.

  19. Reconfigurable optical switches with monolithic electrical-to-optical interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, J.; Zhou, P. [New Mexico Univ., Albuquerque, NM (United States). Center for High Technology Materials; Zolper, J.C.; Lear, K.L.; Vawter, G.A. [Sandia National Labs., Albuquerque, NM (United States); Leibenguth, R.E.; Adams, A.C. [AT and T Bell Labs., Breinigsville, PA (United States)

    1994-03-01

    Vertical cavity surface-emitting lasers (VCSELs) can be integrated with heterojunction phototransistors (HPTs) and heterojunction bipolar transistors (HBTs) on the same wafer to form high speed optical and optoelectronic switches, respectively, that can be optically or electrically addressed. This permits the direct communication and transmission of data between distributed electronic processors through an optical switching network. The experimental demonstration of an integrated optoelectronic HBT/VCSEL switch combining a GaAs/AlGaAs heterojunction bipolar transistor (HBT) with a VCSEL is described below, using the same epilayer structure upon which binary HPT/VCSEL optical switches are also built. The monolithic HBT/VCSEL switch has high current gain, low power dissipation, and a high optical to electrical conversion efficiency. Its modulation has been measured and modeled.

  20. Analysis of monolithic integrated master oscillator power amplifiers

    Science.gov (United States)

    Mehuys, David; Welch, David F.; Waarts, Robert G.; Parke, Ross; Hardy, Amos; Streifer, William

    1991-07-01

    An analysis of a novel, monolithic integrated master oscillator power amplifier (M-MOPA) is presented. The M-MOPA consists of a DBR master oscillator which injects power into a linear chain of amplifiers and detuned second-order grating output couplers. The analysis self-consistently includes amplified spontaneous emission buildup and residual reflections throughout the amplifier stages. It predicts that output powers in excess of 1 W can be expected from a single-lateral-mode waveguide multistage amplifier less than 1 cm in length, injected with less than 15 mW of input power. In addition to the signal gain of more than 25 dB, the signal-to-noise ratio at 1-W output exceeds 15 dB. Because of the small reflections associated with the grating output couplers, and gain saturation by the injected signal, the amplifier self-oscillation threshold is suppressed to current densities above 15 kA/sq cm.

  1. Monolith filter apparatus and membrane apparatus, and method using same

    Energy Technology Data Exchange (ETDEWEB)

    Goldsmith, Robert L [Wayland, MA

    2012-04-03

    A filtration apparatus that separates a liquid feedstock mixed with a gas into filtrate and retentate, the apparatus including at least one filtration device comprised of at least one monolith segment of porous material that defines a plurality of passageways extending longitudinally from a feed face of the structure to a retentate end face. The filtration device contains at least one filtrate conduit within it for carrying filtrate toward a filtrate collection zone, the filtrate conduit providing a path of lower flow resistance than that of alternative flow paths through the porous material of the device. The filtration device can also be utilized as a membrane support for a device for microfiltration, ultrafiltration, nanofiltration, reverse osmosis, or pervaporation. Also disclosed is a method for using such a filtration apparatus.

  2. Minicircle DNA purification using a CIM® DEAE-1 monolithic support.

    Science.gov (United States)

    Diamantino, Tatiana; Pereira, Patrícia; Queiroz, João A; Sousa, Ângela; Sousa, Fani

    2016-09-01

    Minicircle DNA is a new biotechnological product with beneficial therapeutic perspectives for gene therapy because it is constituted only by the eukaryotic transcription unit. These features improve minicircle DNA safety and increase its therapeutic effect. However, being a recently developed product, there is a need to establish efficient purification methodologies, enabling the recovery of the supercoiled minicircle DNA isoform. Thus, this work describes the minicircle DNA purification using an anion exchange monolithic support. The results show that with this column it is possible to achieve a good selectivity, which allows the isolation of the supercoiled minicircle DNA isoform from impurities. Overall, this study shows a promising approach to obtain the minicircle DNA sample with adequate quality for future therapeutic applications.

  3. Heterogeneous Monolithic Integration of Single-Crystal Organic Materials.

    Science.gov (United States)

    Park, Kyung Sun; Baek, Jangmi; Park, Yoonkyung; Lee, Lynn; Hyon, Jinho; Koo Lee, Yong-Eun; Shrestha, Nabeen K; Kang, Youngjong; Sung, Myung Mo

    2017-02-01

    Manufacturing high-performance organic electronic circuits requires the effective heterogeneous integration of different nanoscale organic materials with uniform morphology and high crystallinity in a desired arrangement. In particular, the development of high-performance organic electronic and optoelectronic devices relies on high-quality single crystals that show optimal intrinsic charge-transport properties and electrical performance. Moreover, the heterogeneous integration of organic materials on a single substrate in a monolithic way is highly demanded for the production of fundamental organic electronic components as well as complex integrated circuits. Many of the various methods that have been designed to pattern multiple heterogeneous organic materials on a substrate and the heterogeneous integration of organic single crystals with their crystal growth are described here. Critical issues that have been encountered in the development of high-performance organic integrated electronics are also addressed.

  4. Optical displacement measurement using a monolithic Michelson interferometer

    Science.gov (United States)

    Hofstetter, Daniel; Zappe, Hans P.

    1997-04-01

    Contactless optical displacement measurement has the potential for a variety of industrial and scientific applications. For highly accurate displacement measurements at distances below 1 m, interferometric methods are preferred over most other methods. This is mainly because of the good resolution and the possibility of doing the measurements in real-time. Furthermore, the use of direct bandgap semiconductor materials also enables the fabrication of a compact interferometer-based device which unites all necessary components, including the light emitter, on a single chip. In this paper, a monolithically integrated optical displacement sensor fabricated in the GaAs/AlGaAs material system is reported. This single chip microsystem is configured as a double Michelson interferometer and comprises a distributed Bragg reflector laser, photodetectors, phase shifters and waveguide couplers. In the course of this paper, we will also briefly discuss possible scientific and industrial applications of such devices.

  5. Monolithic interferometer for high precision radial velocity measurements

    Science.gov (United States)

    Wan, Xiaoke; Ge, Jian; Wang, Ji; Lee, Brian

    2009-08-01

    In high precision radial velocity (RV) measurements for extrasolar planets searching and studies, a stable wide field Michelson interferometer is very critical in Exoplanet Tracker (ET) instruments. Adopting a new design, monolithic interferometers are homogenous and continuous in thermal expansion, and field compensation and thermal compensation are both satisfied. Interferometer design and fabrication are decrypted in details. In performance evaluations, field angle is typically 22° and thermal sensitivity is typically -1.7 x 10-6/°C, which corresponds to ~500 m/s /°C in RV scale. In interferometer stability monitoring using a wavelength stabilized laser source, phase shift data was continuously recorded for nearly seven days. Appling a frequent calibration every 30 minutes as in typical star observations, the interferometer instability contributes less than 1.4 m/s in RV error, in a conservative estimation.

  6. Monolithic microwave integrated circuit devices for active array antennas

    Science.gov (United States)

    Mittra, R.

    1984-01-01

    Two different aspects of active antenna array design were investigated. The transition between monolithic microwave integrated circuits and rectangular waveguides was studied along with crosstalk in multiconductor transmission lines. The boundary value problem associated with a discontinuity in a microstrip line is formulated. This entailed, as a first step, the derivation of the propagating as well as evanescent modes of a microstrip line. The solution is derived to a simple discontinuity problem: change in width of the center strip. As for the multiconductor transmission line problem. A computer algorithm was developed for computing the crosstalk noise from the signal to the sense lines. The computation is based on the assumption that these lines are terminated in passive loads.

  7. Method of producing monolithic ceramic cross-flow filter

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, D.A.; Bacchi, D.P.; Connors, T.F.; Collins, E.L. III

    1998-02-10

    Ceramic filter of various configuration have been used to filter particulates from hot gases exhausted from coal-fired systems. Prior ceramic cross-flow filters have been favored over other types, but those previously have been assemblies of parts somehow fastened together and consequently subject often to distortion or delamination on exposure hot gas in normal use. The present new monolithic, seamless, cross-flow ceramic filters, being of one-piece construction, are not prone to such failure. Further, these new products are made by a novel casting process which involves the key steps of demolding the ceramic filter green body so that none of the fragile inner walls of the filter is cracked or broken. 2 figs.

  8. Method of producing monolithic ceramic cross-flow filter

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, David A. (Clifton Park, NY); Bacchi, David P. (Schenectady, NY); Connors, Timothy F. (Watervliet, NY); Collins, III, Edwin L. (Albany, NY)

    1998-01-01

    Ceramic filter of various configuration have been used to filter particulates from hot gases exhausted from coal-fired systems. Prior ceramic cross-flow filters have been favored over other types, but those previously horn have been assemblies of parts somehow fastened together and consequently subject often to distortion or delamination on exposure hot gas in normal use. The present new monolithic, seamless, cross-flow ceramic filters, being of one-piece construction, are not prone to such failure. Further, these new products are made by novel casting process which involves the key steps of demolding the ceramic filter green body so that none of the fragile inner walls of the filter is cracked or broken.

  9. Analysis of the performance of the MONOLITH prototype

    CERN Document Server

    Bari, G; D'Incecco, M; De Deo, M; Garbini, M; Giusti, P; Gustavino, C; Lindozzi, M; Menghetti, H; Sartorelli, G; Satta, G; Selvi, M

    2003-01-01

    In the framework of the study for a large magnetic detector suitable for the physics at a neutrino factory, the data collected with the MONOLITH prototype at the T7-PS facility at CERN has been analyzed. The hadron shower angular resolution for pions followed a 10.4/ root E(GeV) + 10.1/E law for orthogonally incident particles. For a baseline of 732 km, this performance would allow the rejection of wrong sign muon background at the level of 10**-**6, and a capability to measure sintheta//1//3 down to 10**-**3. A preliminary analysis of about 10**6 downward going muons collected at LNGS is also presented. The readout system upgrade allowed the monitoring of each glass RPC with a granularity of 1 cm**2.

  10. Monolithic active pixel radiation detector with shielding techniques

    Science.gov (United States)

    Deptuch, Grzegorz W.

    2016-09-06

    A monolithic active pixel radiation detector including a method of fabricating thereof. The disclosed radiation detector can include a substrate comprising a silicon layer upon which electronics are configured. A plurality of channels can be formed on the silicon layer, wherein the plurality of channels are connected to sources of signals located in a bulk part of the substrate, and wherein the signals flow through electrically conducting vias established in an isolation oxide on the substrate. One or more nested wells can be configured from the substrate, wherein the nested wells assist in collecting charge carriers released in interaction with radiation and wherein the nested wells further separate the electronics from the sensing portion of the detector substrate. The detector can also be configured according to a thick SOA method of fabrication.

  11. Resonant-cavity based monolithic white light-emitting diode

    Science.gov (United States)

    Huang, Lirong; Huang, Dexiu; Wen, Feng

    2007-11-01

    We propose a new scheme of resonant-cavity (RC) based monolithic white LED, it relaxes the hard requirement of high internal quantum efficiency of yellow multi-quantum (MQW) and offers an easy way to obtain high luminous efficacy white light emission. In the proposed white LED, the blue MQW and yellow MQW active layer are embedded in a resonant-cavity defined by the bottom distributed Bragg reflector(DBR) and top DBR. For a optimal design of RC-based white LED, the extraction efficiency for yellow light is enhanced, while that for blue light is suppressed, thus intensity ratio of yellow light in the emitting light is increased, which not only helps to obtain white emission in spite of the low internal quantum efficiency of yellow light, but also doubles luminous efficacy. The color coordinates and luminous flux of the emitting light from RC-based white LED are calculated and the performance dependence on directionality is investigated.

  12. A nanofabricated, monolithic, path-separated electron interferometer

    CERN Document Server

    Agarwal, Akshay; Hobbs, Richard; van Dyck, Dirk; Berggren, Karl K

    2016-01-01

    We report a self-aligned, monolithic electron interferometer, consisting of two 45 nm thick silicon layers separated by 20 $\\mu$m. This interferometer was fabricated from a single crystal silicon cantilever on a transmission electron microscope grid by gallium focused ion-beam milling. Using this interferometer, we demonstrate beam path-separation, and obtain interference fringes in a Mach-Zehnder geometry, in an unmodified 200 kV transmission electron microscope. The fringes have a period of 0.32 nm, which corresponds to the $\\left[\\bar{1}\\bar{1}1\\right]$ lattice planes of silicon, and a maximum contrast of 15 %. This design can potentially be scaled to millimeter-scale, and used in electron holography. It can also be applied to perform fundamental physics experiments, such as interaction-free measurement with electrons.

  13. Monolithic single mode interband cascade lasers with wide wavelength tunability

    Science.gov (United States)

    von Edlinger, M.; Weih, R.; Scheuermann, J.; Nähle, L.; Fischer, M.; Koeth, J.; Kamp, M.; Höfling, S.

    2016-11-01

    Monolithic two-section interband cascade lasers offering a wide wavelength tunability in the wavelength range around 3.7 μm are presented. Stable single mode emission in several wavelength channels was realized using the concept of binary superimposed gratings and two-segment Vernier-tuning. The wavelength selective elements in the two segments were based on specially designed lateral metal grating structures defined by electron beam lithography. A dual-step dry etch process provided electrical separation between the segments. Individual current control of the segments allowed wavelength channel selection as well as continuous wavelength tuning within channels. A discontinuous tuning range extending over 158 nm in up to six discrete wavelength channels was achieved. Mode hop free wavelength tuning up to 14 nm was observed within one channel. The devices can be operated in continuous wave mode up to 30 °C with the output powers of 3.5 mW around room temperature.

  14. Cost and Potential of Monolithic CIGS Photovoltaic Modules

    Energy Technology Data Exchange (ETDEWEB)

    Horowitz, Kelsey; Woodhouse, Michael

    2015-06-17

    A bottom-up cost analysis of monolithic, glass-glass Cu(In,Ga)(Se,S)2 (CIGS) modules is presented, illuminating current cost drivers for this technology and possible pathways to reduced cost. At 14% module efficiency, for the case of U.S. manufacturing, a manufacturing cost of $0.56/WDC and a minimum sustainable price of $0.72/WDC were calculated. Potential for reduction in manufacturing costs to below $0.40/WDC in the long-term may be possible if module efficiency can be increased without significant increase in $/m2 costs. The levelized cost of energy (LCOE) in Phoenix, AZ under different conditions is assessed and compared to standard c-Si.

  15. Nondestructive characterization methods for monolithic solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Ellingson, W.A.

    1993-01-01

    Monolithic solid oxide fuel cells (MSOFCS) represent a potential breakthrough in fuel cell technology, provided that reliable fabrication methods can be developed. Fabrication difficulties arise in several steps of the processing: First is the fabrication of uniform thin (305 {mu}m) single-layer and trilayer green tapes (the trilayer tapes of anode/electrolyte/cathode and anode/interconnect/cathode must have similar coefficients of thermal expansion to sinter uniformly and to have the necessary electrochemical properties); Second is the development of fuel and oxidant channels in which residual stresses are likely to develop in the tapes; Third is the fabrication of a ``complete`` cell for which the bond quality between layers and the quality of the trilayers must be established; and Last, attachment of fuel and oxidant manifolds and verification of seal integrity. Purpose of this report is to assess nondestructive characterization methods that could be developed for application to laboratory, prototype, and full-scale MSOFCs.

  16. GaN Monolithic Power Amplifiers for Microwave Backhaul Applications

    Directory of Open Access Journals (Sweden)

    Roberto Quaglia

    2016-06-01

    Full Text Available Gallium nitride integrated technology is very promising not only for wireless applications at mobile frequencies (below 6 GHz but also for network backhaul radiolink deployment, now under deep revision for the incoming 5G generation of mobile communications. This contribution presents three linear power amplifiers realized on 0.25 μ m Gallium Nitride on Silicon Carbide monolithic integrated circuits for microwave backhaul applications: two combined power amplifiers working in the backhaul band around 7 GHz, and a more challenging third one working in the higher 15 GHz band. Architectures and main design steps are described, highlighting the pros and cons of Gallium Nitride with respect to the reference technology which, for these applications, is represented by gallium arsenide.

  17. Radiation hardness studies on CMOS monolithic pixel sensors

    Energy Technology Data Exchange (ETDEWEB)

    Battaglia, Marco [Department of Physics, University of California at Berkeley, CA 94720 (United States); Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Bisello, Dario [Dipartimento di Fisica, Universita di Padova and INFN, Sezione di Padova, I-35131 Padova (Italy); Contarato, Devis, E-mail: DContarato@lbl.go [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Denes, Peter; Doering, Dionisio [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Giubilato, Piero [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Dipartimento di Fisica, Universita di Padova and INFN, Sezione di Padova, I-35131 Padova (Italy); Sung Kim, Tae [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Mattiazzo, Serena [Dipartimento di Fisica, Universita di Padova and INFN, Sezione di Padova, I-35131 Padova (Italy); Radmilovic, Velimir [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Zalusky, Sarah [Department of Physics, University of California at Berkeley, CA 94720 (United States); Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States)

    2010-12-11

    This paper presents irradiation studies performed on a CMOS monolithic pixel sensor prototype implementing different optimizations of the pixel cell aimed at a superior radiation tolerance. Irradiations with 200 keV electrons up to a total dose of 1.1 Mrad have been performed in view of the utilization of such a design in Transmission Electron Microscopy (TEM) applications. Comparative irradiations were performed with 29 MeV protons up to a 2 Mrad total dose and with 1-14 MeV neutrons up to fluences in excess of 10{sup 13} n{sub eq} cm{sup -2}. Experimental results show an improved performance of pixels designed with Enclosed Layout Transistor (ELT) rules and an optimized layout of the charge collecting diodes.

  18. Monolithic carbide-derived carbon films for micro-supercapacitors.

    Science.gov (United States)

    Chmiola, John; Largeot, Celine; Taberna, Pierre-Louis; Simon, Patrice; Gogotsi, Yury

    2010-04-23

    Microbatteries with dimensions of tens to hundreds of micrometers that are produced by common microfabrication techniques are poised to provide integration of power sources onto electronic devices, but they still suffer from poor cycle lifetime, as well as power and temperature range of operation issues that are alleviated with the use of supercapacitors. There have been a few reports on thin-film and other micro-supercapacitors, but they are either too thin to provide sufficient energy or the technology is not scalable. By etching supercapacitor electrodes into conductive titanium carbide substrates, we demonstrate that monolithic carbon films lead to a volumetric capacity exceeding that of micro- and macroscale supercapacitors reported thus far, by a factor of 2. This study also provides the framework for integration of high-performance micro-supercapacitors onto a variety of devices.

  19. Fast preparation of photopolymerized monolithic columns for capillary electrochromatography

    Institute of Scientific and Technical Information of China (English)

    GONG Wen-jun; XU Guang-ri; ZHANG Yi-jun; ZHANG Yu-ping; CHOI Seong-ho; LEE Kwang-pill

    2008-01-01

    Photopolymerized sol-gel(PSG) columns were prepared using methacryloxypropyltrimethoxysilane as the monomer,toluene as the porogen and hydrochloric acid as the catalyst. Four different photoinitiators such as benzoin methyl ether, Irgacure 819,lrgacure 1700 and Irgacure 1800 were comparatively used in the reaction solution in the presence and absence of sodium dodecylsulfate. The above eight solutions were respectively irradiated at 365 um for 5-10 min in each capillary (75 μm inside diameter) toprepare the porous monolithic sol-gel column by a one-step, in situ, process. The chromatographic behavior of the eight PSGcolumns were comparatively studied, all of which exhibit reversed-phase character. Using these columns, several neutral compounds,namely thiourea, benzene, toluene, ethyl benzene, biphenyl and naphthalene can be separated from mixtures with a largest columnefficiency of 74 470 plate/column for thiourea. Addition of sodium dodecyl sulfate in the polymerization process has a significantinfluence on the morphology and migration time.

  20. Monolithic optofluidic ring resonator lasers created by femtosecond laser nanofabrication.

    Science.gov (United States)

    Chandrahalim, Hengky; Chen, Qiushu; Said, Ali A; Dugan, Mark; Fan, Xudong

    2015-05-21

    We designed, fabricated, and characterized a monolithically integrated optofluidic ring resonator laser that is mechanically, thermally, and chemically robust. The entire device, including the ring resonator channel and sample delivery microfluidics, was created in a block of fused-silica glass using a 3-dimensional femtosecond laser writing process. The gain medium, composed of Rhodamine 6G (R6G) dissolved in quinoline, was flowed through the ring resonator. Lasing was achieved at a pump threshold of approximately 15 μJ mm(-2). Detailed analysis shows that the Q-factor of the optofluidic ring resonator is 3.3 × 10(4), which is limited by both solvent absorption and scattering loss. In particular, a Q-factor resulting from the scattering loss can be as high as 4.2 × 10(4), suggesting the feasibility of using a femtosecond laser to create high quality optical cavities.

  1. Towards monolithic integration of germanium light sources on silicon chips

    Science.gov (United States)

    Saito, Shinichi; Zaher Al-Attili, Abdelrahman; Oda, Katsuya; Ishikawa, Yasuhiko

    2016-04-01

    Germanium (Ge) is a group-IV indirect band gap semiconductor, and therefore bulk Ge cannot emit light efficiently. However, the direct band gap energy is close to the indirect one, and significant engineering efforts are being made to convert Ge into an efficient gain material monolithically integrated on a Si chip. In this article, we will review the engineering challenges of developing Ge light sources fabricated using nano-fabrication technologies compatible with complementary metal-oxide-semiconductor processes. In particular, we review recent progress in applying high-tensile strain to Ge to reduce the direct band gap. Another important technique is doping Ge with donor impurities to fill the indirect band gap valleys in the conduction band. Realization of carrier confinement structures and suitable optical cavities will be discussed. Finally, we will discuss possible applications of Ge light sources in potential photonics-electronics convergent systems.

  2. A High Resolution Monolithic Crystal, DOI, MR Compatible, PET Detector

    Energy Technology Data Exchange (ETDEWEB)

    Robert S Miyaoka

    2012-03-06

    The principle objective of this proposal is to develop a positron emission tomography (PET) detector with depth-of-interaction (DOI) positioning capability that will achieve state of the art spatial resolution and sensitivity performance for small animal PET imaging. When arranged in a ring or box detector geometry, the proposed detector module will support <1 mm3 image resolution and >15% absolute detection efficiency. The detector will also be compatible with operation in a MR scanner to support simultaneous multi-modality imaging. The detector design will utilize a thick, monolithic crystal scintillator readout by a two-dimensional array of silicon photomultiplier (SiPM) devices using a novel sensor on the entrance surface (SES) design. Our hypothesis is that our single-ended readout SES design will provide an effective DOI positioning performance equivalent to more expensive dual-ended readout techniques and at a significantly lower cost. Our monolithic crystal design will also lead to a significantly lower cost system. It is our goal to design a detector with state of the art performance but at a price point that is affordable so the technology can be disseminated to many laboratories. A second hypothesis is that using SiPM arrays, the detector will be able to operate in a MR scanner without any degradation in performance to support simultaneous PET/MR imaging. Having a co-registered MR image will assist in radiotracer localization and may also be used for partial volume corrections to improve radiotracer uptake quantitation. The far reaching goal of this research is to develop technology for medical research that will lead to improvements in human health care.

  3. Initial results for the silicon monolithically interconnected solar cell product

    Science.gov (United States)

    Dinetta, L. C.; Shreve, K. P.; Cotter, J. E.; Barnett, A. M.

    1995-01-01

    This proprietary technology is based on AstroPower's electrostatic bonding and innovative silicon solar cell processing techniques. Electrostatic bonding allows silicon wafers to be permanently attached to a thermally matched glass superstrate and then thinned to final thicknesses less than 25 micron. These devices are based on the features of a thin, light-trapping silicon solar cell: high voltage, high current, light weight (high specific power) and high radiation resistance. Monolithic interconnection allows the fabrication costs on a per watt basis to be roughly independent of the array size, power or voltage, therefore, the cost effectiveness to manufacture solar cell arrays with output powers ranging from milliwatts up to four watts and output voltages ranging from 5 to 500 volts will be similar. This compares favorably to conventionally manufactured, commercial solar cell arrays, where handling of small parts is very labor intensive and costly. In this way, a wide variety of product specifications can be met using the same fabrication techniques. Prototype solar cells have demonstrated efficiencies greater than 11%. An open-circuit voltage of 5.4 volts, fill factor of 65%, and short-circuit current density of 28 mA/sq cm at AM1.5 illumination are typical. Future efforts are being directed to optimization of the solar cell operating characteristics as well as production processing. The monolithic approach has a number of inherent advantages, including reduced cost per interconnect and increased reliability of array connections. These features make this proprietary technology an excellent candidate for a large number of consumer products.

  4. Mineral Fiber Toxicology

    Science.gov (United States)

    The chemical and physical properties of different forms of mineral fibers impact biopersistence and pathology in the lung. Fiber chemistry, length, aspect ratio, surface area and dose are critical factors determining mineral fiber-associated health effects including cancer and as...

  5. Mineral commodity summaries 2017

    Science.gov (United States)

    Ober, Joyce A.

    2017-01-31

    This report is the earliest Government publication to furnish estimates covering 2016 nonfuel mineral industry data. Data sheets contain information on the domestic industry structure, Government programs, tariffs, and 5-year salient statistics for more than 90 individual minerals and materials.

  6. Marine Mineral Exploration

    DEFF Research Database (Denmark)

    The past 20 years have seen extensive marine exploration work by the major industrialized countries. Studies have, in part, been concentrated on Pacific manganese nodule occurrences and on massive sulfides on mid-oceanic ridges. An international jurisdictional framework of the sea-bed mineral...... in EEZ areas are fairly unknown; many areas need detailed mapping and mineral exploration, and the majority of coastal or island states with large EEZ areas have little experience in exploration for marine hard minerals. This book describes the systematic steps in marine mineral exploration....... Such exploration requires knowledge of mineral deposits and models of their formation, of geophysical and geochemical exploration methods, and of data evaluation and interpretation methods. These topics are described in detail by an international group of authors. A short description is also given of marine...

  7. Synthesis of novel hierarchical ZSM-5 monoliths and their application in trichloroethylene removal

    Institute of Scientific and Technical Information of China (English)

    João Pires; Ana C.Fernandes; Divakar Duraiswami

    2014-01-01

    A self-supporting ZSM-5 monolith with a hierarchical porosity was prepared using polyurethane foam (PUF) as a structural template and a hydrothermal synthesis procedure. The synthesized monolith was characterized and investigated towards the adsorption and catalytic oxidation of trichloroethylene (TCE). Adsorption of TCE was studied gravimetrically and oxidation of TCE was studied using a vapor-phase down-flow reactor. Monolithic ZSM-5 displayed good sorption proper-ties and completely oxidized TCE. Conversion levels of 50%and 90%were achieved at reduced temperatures (by~50 °C) when compared with the conversion temperatures obtained from the powder counterparts. Besides the activity of the monolith towards TCE adsorption and oxidation, it was stable and enhanced diffusion, thereby reducing pressure drops to a great extent owing to its hierarchical porous nature.

  8. Monolithically integrated AlN/GaN electronics for harsh environments Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Recently, resonant-tunneling-diode (RTD) based circuits employing monolithically-integrated RTD on high electron mobility (HEMT) structures have been developed in a...

  9. Single step synthesis of carbohydrate monolithic capillary columns for affinity chromatography of lectins

    NARCIS (Netherlands)

    Tetala, K.K.R.; Chen, B.; Visser, G.M.; Beek, van T.A.

    2007-01-01

    Carbohydrate monolithic beds were synthesized in a single step in capillary columns to study affinity chromatography of lectins. In this method, carbohydrates (-galactose, -glucose, and -mannose) with an easy to synthesize alkene terminated tetraethylene glycol spacer were used as functional

  10. Broadband EM Performance Characteristics of Single Square Loop FSS Embedded Monolithic Radome

    Directory of Open Access Journals (Sweden)

    Raveendranath U. Nair

    2013-01-01

    Full Text Available A monolithic half-wave radome panel, centrally loaded with aperture-type single square loop frequency selective surface (SSL-FSS, is proposed here for broadband airborne radome applications. Equivalent transmission line method in conjunction with equivalent circuit model (ECM is used for modeling the SSL-FSS embedded monolithic half-wave radome panel and evaluating radome performance parameters. The design parameters of the SSL-FSS are optimized at different angles of incidence such that the new radome wall configuration offers superior EM performance from L-band to X-band as compared to the conventional monolithic half-wave slab of identical material and thickness. The superior EM performance of SSL-FSS embedded monolithic radome wall makes it suitable for the design of normal incidence and streamlined airborne radomes.

  11. Convective Interaction Media (CIM)--short layer monolithic chromatographic stationary phases.

    Science.gov (United States)

    Podgornik, Ales; Strancar, Ales

    2005-01-01

    Modern downstream processing requires fast and highly effective methods to obtain large quantities of highly pure substances. Commonly applied method for this purpose is chromatography. However, its main drawback is its throughput since purification, especially of large molecules, requires long process time. To overcome this problem several new stationary phases were introduced, among which short layer monoliths show superior properties for many applications. The purpose of this review is to give an overview about short methacrylate monolithic columns commercialised under the trademark Convective Interaction Media (CIM). Their unique properties are described from different perspectives, explaining reasons for their application on various areas. Approaches to prepare large volume methacrylate monolithic column are discussed and optimal solutions are given. Different examples of CIM monolithic column implementation are summarised in the last part of the article to give the reader an idea about their advantages.

  12. Monolithic three-dimensional electrochemical energy storage system on aerogel or nanotube scaffold

    Science.gov (United States)

    Farmer, Joseph C; Stadermann, Michael

    2013-11-12

    A monolithic three-dimensional electrochemical energy storage system is provided on an aerogel or nanotube scaffold. An anode, separator, cathode, and cathodic current collector are deposited on the aerogel or nanotube scaffold.

  13. New monolithic enzymatic micro-reactor for the fast production and purification of oligogalacturonides.

    Science.gov (United States)

    Delattre, C; Michaud, P; Vijayalakshmi, M A

    2008-01-15

    Fast production and purification of alpha-(1,4)-oligogalacturonides was investigated using a new enzymatic reactor composed of a monolithic matrix. Pectin lyase from Aspergillus japonicus (Sigma) was immobilized on CIM-disk epoxy monolith. Studies were performed on free pectin lyase and immobilized pectin lyase to compare the optimum temperature, optimum pH, and thermal stability. It was determined that optimum temperature for free pectin lyase and immobilized pectin lyase on monolithic support is 30 degrees C, and optimum pH is 5. Monolithic CIM-disk chromatography is one of the fastest liquid chromatographic method used for separation and purification of biomolecules due to high mass transfer rate. In this context, online one step production and purification of oligogalacturonides was investigated associating CIM-disk pectin lyase and CIM-disk DEAE. This efficient enzymatic bioreactor production of uronic oligosaccharides from polygalacturonic acid (PGA) constitutes an original fast process to generate bioactive oligouronides.

  14. Monolithic distributed Bragg reflector cavities in Al2O3 with quality factors exceeding one million

    NARCIS (Netherlands)

    Bernhardi, Edward; van Wolferen, Hendricus A.G.M.; Worhoff, Kerstin; de Ridder, R.M.; Pollnau, Markus

    Monolithic distributed Bragg reflector (DBR) cavities with quality factors exceeding one million have been realized in aluminum oxide channel waveguides. This technology enabled the successful demonstration of the first DBR laser in this waveguide platform.

  15. Recycle Adsorption of Cu2+ on Amine-functionalized Mesoporous Silica Monolithic

    Institute of Scientific and Technical Information of China (English)

    ZHAO Da-zhou; JING Shu-bo; XU Jia-ning; YANG Hong; ZHENG Wei; SONG Tian-you; ZHANG Ping

    2013-01-01

    3-Aminopropyltriethoxysilane functionalized worm-like mesoporous silica monolithic(WMSM-NH2) was prepared and used as a new regenerable adsorbent for the removal of Cu2+ ions.The analysis results show that the WMSM-NH2 monolithic had a high efficiency value of 99.3% for Cu2+ remediation when the Cu2+ solution was at an initial concentration of 10.32 mg/L.The regeneration study of the WMSM-NH2 monolithic presented that the adsorption efficiency of 89.0% was remained and a mass of 92.0% was left after seven adsorption-desorption cycles were executed.The monolithic material with high resistance to the acid and good mechanical stability can facilitate the operations of adsorption and regeneration of the adsorbent.

  16. Feasibility of the preparation of silica monoliths for gas chromatography: fast separation of light hydrocarbons.

    Science.gov (United States)

    Azzouz, Imadeddine; Essoussi, Anouar; Fleury, Joachim; Haudebourg, Raphael; Thiebaut, Didier; Vial, Jerome

    2015-02-27

    The preparation conditions of silica monoliths for gas chromatography were investigated. Silica-based monolithic capillary columns based on sol-gel process were tested in the course of high-speed gas chromatographic separations of light hydrocarbons mixture (C1-C4). The impact of modifying the amount of porogen and/or catalyst on the monolith properties were studied. At the best precursor/catalyst/porogen ratio evaluated, a column efficiency of about 6500 theoretical plates per meter was reached with a very good resolution (4.3) for very light compounds (C1-C2). The test mixture was baseline separated on a 70cm column. To our knowledge for the first time a silica-based monolithic capillary column was able to separate light hydrocarbons from methane to n-butane at room temperature with a back pressure in the range of gas chromatography facilities (under 4.1bar).

  17. Monolithic three-dimensional electrochemical energy storage system on aerogel or nanotube scaffold

    Science.gov (United States)

    Farmer, Joseph Collin; Stadermann, Michael

    2014-07-15

    A monolithic three-dimensional electrochemical energy storage system is provided on an aerogel or nanotube scaffold. An anode, separator, cathode, and cathodic current collector are deposited on the aerogel or nanotube scaffold.

  18. A Monolithic, Non-Field-Widened Spatial Heterodyne Spectrometer for Solar System Exploration Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The goal of this project is to produce a monolithic Spatial Heterodyne Spectrometer (a Fourier Transform Interferometer) for use in Solar System exploration. In...

  19. Fabrication of interfacial functionalized porous polymer monolith and its adsorption properties of copper ions.

    Science.gov (United States)

    Han, Jiaxi; Du, Zhongjie; Zou, Wei; Li, Hangquan; Zhang, Chen

    2014-07-15

    The interfacial functionalized poly (glycidyl methacrylate) (PGMA) porous monolith was fabricated and applied as a novel porous adsorbent for copper ions (Cu(2+)). PGMA porous material with highly interconnected pore network was prepared by concentrated emulsion polymerization template. Then polyacrylic acid (PAA) was grafted onto the interface of the porous monolith by the reaction between the epoxy group on PGMA and a carboxyl group on PAA. Finally, the porous monolith was interfacial functionalized by rich amount of carboxyl groups and could adsorb copper ions effectively. The chemical structure and porous morphology of the porous monolith were measured by Fourier transform infrared spectroscopy and scanning electron microscopy. Moreover, the effects of pore size distribution, pH value, co-existing ions, contacting time, and initial concentrations of copper ions on the adsorption capacity of the porous adsorbents were studied.

  20. Mineral Commodity Summaries 2008

    Science.gov (United States)

    ,

    2008-01-01

    Each chapter of the 2008 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2007 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses. National reserves and reserve base information for most mineral commodities found in this report, including those for the United States, are derived from a variety of sources. The ideal source of such information would be comprehensive evaluations that apply the same criteria to deposits in different geographic areas and report the results by country. In the absence of such evaluations, national reserves and reserve base estimates compiled by countries for selected mineral commodities are a primary source of national reserves and reserve base information. Lacking national assessment information by governments, sources such as academic articles, company reports, common business practice, presentations by company representatives, and trade journal articles, or a combination of these, serve as the basis for national reserves and reserve base information reported in the mineral commodity sections of this publication. A national estimate may be assembled from the following: historically reported reserves and reserve base information carried for years without alteration because no new information is available; historically reported reserves and reserve base reduced by the amount of historical production; and company reported reserves. International minerals availability studies conducted by the U.S. Bureau of Mines, before 1996, and estimates of identified resources by an international collaborative effort (the International Strategic Minerals

  1. Why Mineral Interfaces Matter

    Science.gov (United States)

    Putnis, Andrew; Putnis, Christine V.

    2015-04-01

    While it is obvious that reactions between a mineral and an aqueous solution take place at the mineral-fluid interface it is only relatively recently that high spatial resolution studies have demonstrated how the local structure of the mineral surface and the chemical composition of the fluid at the interface control both the short-range and the long-range consequences of mineral-fluid interaction. Long-range consequences of fluid-mineral interaction control element cycles in the earth, the formation of ore-deposits, the chemical composition of the oceans through weathering of rocks and hence climate changes. Although weathering is clearly related to mineral dissolution, to what extent do experimentally measured dissolution rates of minerals help to understand weathering, especially weathering mechanisms? This question is related to the short-range, local reactions that take place when a mineral, that is not stable in the fluid, begins to dissolve. In this case the fluid composition at the interface will become supersaturated with respect to a different phase or phases. This may be a different composition of the same mineral e.g. a Ca-rich feldspar dissolving in a Na-rich solution results in a fluid at the interface which may be supersaturated with respect to an Na-rich feldspar. Alternatively, the interfacial fluid could be supersaturated with respect to a different mineral e.g. an Na-rich zeolite, depending on the temperature. Numerous experiments have shown that the precipitation of a more stable phase at the mineral-fluid interface results in a coupling between the dissolution and the precipitation, and the replacement of one mineral by another. This process separates the short-range mechanisms which depend only on the composition of the interfacial solution, and the long-range consequences that depend on the composition of the residual fluid released from the reacting parent mineral. Typically such residual fluids may carry metal ions tens to hundreds of

  2. Influence of the preparation design and artificial aging on the fracture resistance of monolithic zirconia crowns

    OpenAIRE

    Mitov, Gergo; Anastassova-Yoshida, Yana; Nothdurft, Frank Phillip; von See, Constantin; Pospiech, Peter

    2016-01-01

    PURPOSE The aim of this study was to evaluate the fracture resistance and fracture behavior of monolithic zirconia crowns in accordance with the preparation design and aging simulation method. MATERIALS AND METHODS An upper first molar was prepared sequentially with three different preparation designs: shoulderless preparation, 0.4 mm chamfer and 0.8 mm chamfer preparation. For each preparation design, 30 monolithic zirconia crowns were fabricated. After cementation on Cr-Co alloy dies, the f...

  3. Silica-based polypeptide-monolithic stationary phase for hydrophilic chromatography and chiral separation.

    Science.gov (United States)

    Zhao, Licong; Yang, Limin; Wang, Qiuquan

    2016-05-13

    Glutathione (GSH)-, somatostatin acetate (ST)- and ovomucoid (OV)-functionalized silica-monolithic stationary phases were designed and synthesized for HILIC and chiral separation using capillary electrochromatography (CEC). GSH, ST and OV were covalently incorporated into the silica skeleton via the epoxy ring-opening reaction between their amino groups and the glycidyl moiety in γ-glycidoxypropyltrimethoxysilane (GPTMS) together with polycondensation and copolymerization of tetramethyloxysilane and GPTMS. Not only could the direction and electroosmotic flow magnitude on the prepared GSH-, ST- and OV-silica hybrid monolithic stationary phases be controlled by the pH of the mobile phase, but also a typical HILIC behavior was observed so that the nucleotides and HPLC peptide standard mixture could be baseline separated using an aqueous mobile phase without any acetonitrile during CEC. Moreover, the prepared monolithic columns had a chiral separation ability to separate dl-amino acids. The OV-silica hybrid monolithic column was most effective in chiral separation and could separate dl-glutamic acid (Glu) (the resolution R=1.07), dl-tyrosine (Tyr) (1.57) and dl-histidine (His) (1.06). Importantly, the chiral separation ability of the GSH-silica hybrid monolithic column could be remarkably enhanced when using gold nanoparticles (AuNPs) to fabricate an AuNP-mediated GSH-AuNP-GSH-silica hybrid monolithic column. The R of dl-Glu, dl-Tyr and dl-His reached 1.19, 1.60 and 2.03. This monolithic column was thus applied to separate drug enantiomers, and quantitative separation of all four R/S drug enantiomers were achieved with R ranging from 4.36 to 5.64. These peptide- and protein-silica monolithic stationary phases with typical HILIC separation behavior and chiral separation ability implied their promise for the analysis of not only the future metabolic studies, but also drug enantiomers recognition.

  4. Structure and properties of hybrid poly(2-hydroxyethyl methacrylate)/SiO2 monoliths

    DEFF Research Database (Denmark)

    Ji, Xiangling; Jiang, Shichun; Qiu, Xuepeng

    2003-01-01

    Abstract: Hybrid poly(2-hydroxyethyl methacrylate) (PHEMA)/SiO2 monoliths were synthesized via a sol-gel process of the precursor tetraethyl orthosilicate (TEOS) and the in situ free-radical polymerization of 2-hydroxyethyl methacrylate (HEMA). The weight ratio of the starting chemicals, TEOS to ...... related to some degree of chemical crosslinking between the polymer and the silica moiety, which would greatly improve the thermal stability of such hybrid monoliths compared with a pure PHEMA....

  5. A Mathematical Model for Diffusion-Controlled Monolithic Matrix Coated with outer Membrane System

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A release model for diffusion-controlled monolithic matrix coated with outer membrane system is proposed and solved by using the refined double integral method. The calculated results are in satisfactory agreement with the experimental release data. The present model can be well used to describe the release process for all cd/cs values. In addition, the release effects of the monolithic matrix coated with outer membrane system are discussed theoretically.

  6. Influence of Specimen Preparation and Test Methods on the Flexural Strength Results of Monolithic Zirconia Materials

    OpenAIRE

    Christine Schatz; Monika Strickstrock; Malgorzata Roos; Daniel Edelhoff; Marlis Eichberger; Isabella-Maria Zylla; Bogna Stawarczyk

    2016-01-01

    The aim of this work was to evaluate the influence of specimen preparation and test method on the flexural strength results of monolithic zirconia. Different monolithic zirconia materials (Ceramill Zolid (Amann Girrbach, Koblach, Austria), Zenostar ZrTranslucent (Wieland Dental, Pforzheim, Germany), and DD Bio zx2 (Dental Direkt, Spenge, Germany)) were tested with three different methods: 3-point, 4-point, and biaxial flexural strength. Additionally, different specimen preparation methods wer...

  7. Influence of specimen preparation and test methods on the flexural strength results of monolithic zirconia materials

    OpenAIRE

    Schatz, Christine; Strickstrock, Monika; Roos, Malgorzata; Edelhoff, Daniel; Eichberger, Marlis; Zylla, Isabella-Maria; Stawarczyk, Bogna

    2016-01-01

    The aim of this work was to evaluate the influence of specimen preparation and test method on the flexural strength results of monolithic zirconia. Different monolithic zirconia materials (Ceramill Zolid (Amann Girrbach, Koblach, Austria), Zenostar ZrTranslucent (Wieland Dental, Pforzheim, Germany), and DD Bio zx2 (Dental Direkt, Spenge, Germany)) were tested with three different methods: 3-point, 4-point, and biaxial flexural strength. Additionally, different specimen preparation methods wer...

  8. New monolith technology for automated anion-exchange purification of nucleic acids.

    Science.gov (United States)

    Thayer, J R; Flook, K J; Woodruff, A; Rao, S; Pohl, C A

    2010-04-15

    Synthetic nucleic acid analysis often employs pellicular anion-exchange (AE) chromatography because it supports very high efficiency separations while offering means to control secondary structure, retention and resolution by readily modifiable chromatographic conditions. However, these pellicular anion-exchange (pAE) phases do not offer capacity sufficient for lab-scale oligonucleotide (ON) purification. In contrast, monolithic phases produce fast separations at capacities exceeding their pellicular counterparts, but do not exhibit capacities typical of fully porous, bead-based, anion-exchangers. In order to further increase monolith capacity and obtain the selectivity and mass transfer characteristics of pellicular phases, a surface-functionalized monolith was coated with pAE nanobeads (latexes) usually employed on the pellicular DNAPac phase. The nanobead-coated monolith exhibited chromatographic behaviors typical of polymer AE phases. Based on this observation the monolithic substrate surface porosity and latex diameters were co-optimized to produce a hybrid monolith harboring capacity similar to that of fully porous bead-based phases and peak shape approaching that of the pAE phases. We tested the hybrid monolith on a variety of previously developed pAE capabilities including control of ON selectivity, resolution of derivatized ONs, the ability to resolve RNA ONs harboring aberrant linkages at different positions in a single sequence and separation of phosphorothioate diastereoisomers. We compared the yield and purity of an 8 mg ON sample purified on both the new hybrid monolith and a benchmark AE column based on fully porous monodisperse beads. This comparison included an assessment of the relative selectivities of both columns. Finally, we demonstrated the ability to couple AE ON separations with ESI-MS using an automated desalting protocol. This protocol is also useful for preparing ONs for other assays, such as enzyme treatments, that may be sensitive to

  9. Preparation of Monolithic Column and Its Application in p-CEC

    Institute of Scientific and Technical Information of China (English)

    Jun Jiao YANG; Kai ZHANG; Ru Yu GAO; Yu Kui ZHANG; Chao YAN

    2004-01-01

    A novel monolithic stationary phase having long alkyl chain ligands was introduced and evaluated in pressurized-capillary electrochromatography of small neutral and charged compounds.The monolithic column was prepared by the in situ copolymerization of ethylene dimethacrylate,1-hexadecene,allyl alcohol and 2-acrylamido-2-methyl-1-propanesulfonic acid in a quaternary porogenic solvent mixture consisting of 1,4-butanediol,cyclohexanol,dodecanol and water.

  10. THE CHANGE IN DEFORMATION CHARACTERISTICS OF CONCRETE MONOLITHIC HIGH-RISE BUILDINGS

    Directory of Open Access Journals (Sweden)

    V. V. Punahin

    2009-03-01

    Full Text Available In the article results of studies of deformation features of concrete on actuate cement for monolithic high-altitude buildings are presented. It is shown that in construction of the high-altitude monolithic buildings in a summer period of a year one should take into account the character of changing the concrete elasticity and plasticity in time, which differs from the same indices for the concrete of normal hardening.

  11. An Inexpensive Field-Widened Monolithic Michelson Interferometer for Precision Radial Velocity Measurements

    OpenAIRE

    Mahadevan, Suvrath; Ge, Jian; Fleming, Scott W.; Wan, Xiaoke; DeWitt, Curtis; van Eyken, Julian C.; McDavitt, Dan

    2008-01-01

    We have constructed a thermally compensated field-widened monolithic Michelson interferometer that can be used with a medium-resolution spectrograph to measure precise Doppler radial velocities of stars. Our prototype monolithic fixed-delay interferometer is constructed with off-the-shelf components and assembled using a hydrolysis bonding technique. We installed and tested this interferometer in the Exoplanet Tracker (ET) instrument at the Kitt Peak 2.1m telescope, an instrument built to dem...

  12. Two stage dual gate MESFET monolithic gain control amplifier for Ka-band

    Science.gov (United States)

    Sokolov, V.; Geddes, J.; Contolatis, A.

    A monolithic two stage gain control amplifier has been developed using submicron gate length dual gate MESFETs fabricated on ion implanted material. The amplifier has a gain of 12 dB at 30 GHz with a gain control range of over 30 dB. This ion implanted monolithic IC is readily integrable with other phased array receiver functions such as low noise amplifiers and phase shifters.

  13. Maxillary cement retained implant supported monolithic zirconia prosthesis in a full mouth rehabilitation: a clinical report

    OpenAIRE

    Sadid-Zadeh, Ramtin; Liu, Perng-Ru; Aponte-Wesson, Ruth; O'Neal, Sandra J

    2013-01-01

    This clinical report presents the reconstruction of a maxillary arch with a cement retained implant supported fixed prosthesis using a monolithic zirconia generated by CAD/CAM system on eight osseointegrated implants. The prosthesis was copy milled from an interim prosthesis minimizing occlusal adjustments on the definitive prosthesis at the time of delivery. Monolithic zirconia provides high esthetics and reduces the number of metal alloys used in the oral cavity.

  14. Maxillary cement retained implant supported monolithic zirconia prosthesis in a full mouth rehabilitation: a clinical report.

    Science.gov (United States)

    Sadid-Zadeh, Ramtin; Liu, Perng-Ru; Aponte-Wesson, Ruth; O'Neal, Sandra J

    2013-05-01

    This clinical report presents the reconstruction of a maxillary arch with a cement retained implant supported fixed prosthesis using a monolithic zirconia generated by CAD/CAM system on eight osseointegrated implants. The prosthesis was copy milled from an interim prosthesis minimizing occlusal adjustments on the definitive prosthesis at the time of delivery. Monolithic zirconia provides high esthetics and reduces the number of metal alloys used in the oral cavity.

  15. Mineral facilities of Europe

    Science.gov (United States)

    Almanzar, Francisco; Baker, Michael S.; Elias, Nurudeen; Guzman, Eric

    2010-01-01

    This map displays over 1,700 records of mineral facilities within the countries of Europe and western Eurasia. Each record represents one commodity and one facility type at a single geographic location. Facility types include mines, oil and gas fields, and plants, such as refineries, smelters, and mills. Common commodities of interest include aluminum, cement, coal, copper, gold, iron and steel, lead, nickel, petroleum, salt, silver, and zinc. Records include attributes, such as commodity, country, location, company name, facility type and capacity (if applicable), and latitude and longitude geographical coordinates (in both degrees-minutes-seconds and decimal degrees). The data shown on this map and in table 1 were compiled from multiple sources, including (1) the most recently available data from the U.S. Geological Survey (USGS) Minerals Yearbook (Europe and Central Eurasia volume), (2) mineral statistics and information from the USGS Minerals Information Web site (http://minerals.usgs.gov/minerals/pubs/country/europe.html), and (3) data collected by the USGS minerals information country specialists from sources, such as statistical publications of individual countries, annual reports and press releases of operating companies, and trade journals. Data reflect the most recently published table of industry structure for each country at the time of this publication. Additional information is available from the country specialists listed in table 2.

  16. Polymer monolith microextraction using poly(butyl methacrylate-co-1,6-hexanediol ethoxylate diacrylate) monolithic sorbent for determination of phenylurea herbicides in water samples.

    Science.gov (United States)

    Lin, Shu-Ling; Wu, Yu-Ru; Fuh, Ming-Ren

    2016-01-15

    In this study, recently developed 1,6-hexanediol ethoxylate diacrylate (HEDA)-based polymeric monoliths were utilized as sorbents for efficient extraction of phenylurea herbicides (PUHs) from water samples. The HEDA-based monolithic sorbents were prepared in a fused silica capillary (0.7mm i.d., 4.5-cm long) for polymer monolith microextraction (PMME). The experimental parameters of PMME microextraction including sample loading speed, pH of sample solution, composition of elution solvent, and addition of salt were optimized to efficiently extract PUHs from environmental water samples. The extracted PUHs were determined using ultra-high performance liquid chromatography (UHPLC) with UV-photodiode array detection. The extraction recoveries for PUHs-spiked water samples were 91.1-108.1% with relative standard deviations lower than 5%. The linearity range was 0.025-25ngmL(-1) for each PUH and the detection limits of PUHs were estimated at 0.006-0.019ng mL(-1). In addition, good intra-day/inter-day precision (0.1-8.7%/0.2-8.9%) and accuracy (92.0-108.0%/96.5-105.2%) of the proposed method were obtained. The extraction capacity of the monolith-filled capillary was also determined to be approximately 1μg. Moreover, each monolith-filled capillary could be reused up to 8 times without carry-over. According to the European Union regulations, the allowed permissible limit of any single herbicide in drinking water is 0.1ng mL(-1). This permissible level fell in the linear range examined in this study. In addition, the proposed method provided detection limits lower than the allowed permissible level, which demonstrated the feasibility of utilizing the HEDA-based monolithic sorbent to perform PMME for determining contaminants, such as PUHs, in environmental application.

  17. Effect of Silica on High-Temperature Interfacial Phenomena of Monolithic Refractories with Al Alloy

    Science.gov (United States)

    Koshy, Pramod; Gupta, Sushil; Sahajwalla, Veena; Edwards, Phil

    2008-04-01

    An experimental study was conducted to study the interfacial phenomena between monolithic refractories and Al alloy at 1250 °C. Dynamic contact angles of monolithic substrates with varying silica levels were measured using the sessile drop technique, while phases present in the preheated monolithic samples and interfacial reaction products were characterized using X-ray diffraction (XRD) and an electron probe microanalyzer (EPMA). The contact angles in the Al alloy/silica system were found to change much more rapidly as compared to that of the alloy/alumina system, clearly demonstrating the high wetting tendency of silica. Under the tested conditions, the corundum phase forms at the interface while Mg was found to vaporize from the alloy and accumulate at the bottom of the monolithic substrate. Both these phenomena are shown to influence the intensity of contact angle variations with time and, thereby, the wetting behavior of monolithic substrates. Based on dynamic contact angles and equilibrium calculations, monolithic refractories are further classified into three groups, such that the wetting characteristics of those with compositions in the ranges of 0 to 25 pct, 25 to 45 pct, and >45 pct silica were shown to be dictated by the presence of corundum, mullite, and free silica, respectively, as the predominant phase.

  18. Preparation of porous polymer monoliths featuring enhanced surface coverage with gold nanoparticles

    KAUST Repository

    Lv, Yongqin

    2012-10-01

    A new approach to the preparation of porous polymer monoliths with enhanced coverage of pore surface with gold nanoparticles has been developed. First, a generic poly(glycidyl methacrylate-co-ethylene dimethacrylate) monolith was reacted with cystamine followed by the cleavage of its disulfide bonds with tris(2-carboxylethyl)phosphine, which liberated the desired thiol groups. Dispersions of gold nanoparticles with sizes varying from 5 to 40. nm were then pumped through the functionalized monoliths. The materials were then analyzed using both energy dispersive X-ray spectroscopy and thermogravimetric analysis. We found that the quantity of attached gold was dependent on the size of nanoparticles, with the maximum attachment of more than 60. wt% being achieved with 40. nm nanoparticles. Scanning electron micrographs of the cross sections of all the monoliths revealed the formation of a non-aggregated, homogenous monolayer of nanoparticles. The surface of the bound gold was functionalized with 1-octanethiol and 1-octadecanethiol, and these monolithic columns were used successfully for the separations of proteins in reversed phase mode. The best separations were obtained using monoliths modified with 15, 20, and 30. nm nanoparticles since these sizes produced the most dense coverage of pore surface with gold. © 2012 Elsevier B.V.

  19. Ionic liquid-regenerated macroporous cellulose monolith: Fabrication, characterization and its protein chromatography.

    Science.gov (United States)

    Du, Kaifeng

    2017-04-21

    Macroporous cellulose monolith as chromatographic support was successfully fabricated from an ionic liquid dissolved cellulose solution by an emulsification method and followed by the cross-linking reaction and DEAE modification. With the physical characterization, the cellulose monolith featured by both the interconnected macropores in range of 0.5-2.5μm and the diffusion pores centered at about 10nm. Given the bimodal pore system, the monolith possessed the specific surface area of 36.4m(2)g(-1) and the column permeability of about 7.45×10(-14)m(2). After the DEAE modification, the anion cellulose monolith was evaluated for its chromatography performances. It demonstrated that the static and dynamic adsorption capacity of BSA reached about 66.7mgmL(-1) and 43.9mgmL(-1) at 10% breakthrough point, respectively. The results were comparable to other chromatographic adsorbent. In addition, the proteins mixture with different pI was well separated at high flow velocity (611.0cmh(-1)) and high protein recovery (over 97%), proving the macroporous cellulose monolith had excellent separation performance. In this way, the prepared cellulose monolith with bimodal pores system is expected for the potential application in high-speed chromatography. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Fracture Strength of Aged Monolithic and Bilayer Zirconia-Based Crowns.

    Science.gov (United States)

    Lameira, Deborah Pacheco; Buarque e Silva, Wilkens Aurélio; Andrade e Silva, Frederico; De Souza, Grace M

    2015-01-01

    The purpose of this study was to evaluate the effect of design and surface finishing on fracture strength of yttria-tetragonal zirconia polycrystal (Y-TZP) crowns in monolithic (1.5 mm thickness) and bilayer (0.8 mm zirconia coping and 0.7 mm porcelain veneer) configuration after artificial aging. Bovine incisors received crown preparation and Y-TZP crowns were manufactured using CAD/CAM technique, according to the following groups (n = 10): Polished monolithic zirconia crowns (PM); Glazed monolithic zirconia crowns (GM); Bi-layer crowns (BL). Crowns were cemented with resin cement, submitted to artificial aging in a chewing simulator (2.5 million cycles/80 N/artificial saliva/37 °C), and tested for fracture strength. Two remaining crowns referring to PM and GM groups were submitted to a chemical composition analysis to measure the level of yttrium after aging. One-way ANOVA and Tukey's test (P = .05) indicated that monolithic zirconia crowns presented similar fracture strength (PM = 3476.2 N ± 791.7; GM = 3561.5 N ± 991.6), which was higher than bilayer crowns (2060.4 N ± 810.6). There was no difference in the yttrium content among the three surfaces evaluated in the monolithic crowns. Thus, monolithic zirconia crowns present higher fracture strength than bilayer veneered zirconia after artificial aging and surface finishing does not affect their fracture strength.

  1. Purge and trap with monolithic sorbent for gas chromatographic analysis of pesticides in honey.

    Science.gov (United States)

    Chienthavorn, Orapin; Dararuang, Kanittha; Sasook, Anupop; Ramnut, Narumol

    2012-01-01

    Polydivinylbenzene (P-DVB) and silica monolithic materials were synthesised in capillaries and then used to adsorb nine organonitrogen pesticides extracted from honey. After adsorption, each monolith-capillary was connected to a gas chromatograph (GC) with nitrogen-phosphorous detector (NPD). The silica monolith gave better peak shape and intensity than the P-DVB monolith. Formulation of silica monolith with tetramethoxysilane (TMOS) as a sole initiator provided better separation and higher peak intensity, compared to those with methyltrimethoxysilane (MTMS) and (3:1) TMOS/MTMS initiators. The optimum internal diameter and length of silica monolith-capillary were 0.25 mm and 5 cm, respectively. The purge and trap conditions were optimised by purging with nitrogen and heating the honey sample solution at 100 °C for 60 min. Recovery of the method was in a range of 84.95-99.71% and the detection limits of the pesticides determined by using GC-NPD and GC-mass spectrometric detector (MSD) ranged between 0.36-1.75 and 0.13-0.25 ng g(-1), respectively.

  2. Remotely detected NMR for the characterization of flow and fast chromatographic separations using organic polymer monoliths.

    Science.gov (United States)

    Teisseyre, Thomas Z; Urban, Jiri; Halpern-Manners, Nicholas W; Chambers, Stuart D; Bajaj, Vikram S; Svec, Frantisek; Pines, Alexander

    2011-08-01

    An application of remotely detected magnetic resonance imaging is demonstrated for the characterization of flow and the detection of fast, small molecule separations within hypercrosslinked polymer monoliths. The hyper-cross-linked monoliths exhibited excellent ruggedness, with a transit time relative standard deviation of less than 2.1%, even after more than 300 column volumes were pumped through at high pressure and flow. Magnetic resonance imaging enabled high-resolution intensity and velocity-encoded images of mobile phase flow through the monolith. The images confirm that the presence of a polymer monolith within the capillary disrupts the parabolic laminar flow profile that is characteristic of mobile phase flow within an open tube. As a result, the mobile phase and analytes are equally distributed in the radial direction throughout the monolith. Also, in-line monitoring of chromatographic separations of small molecules at high flow rates is shown. The coupling of monolithic chromatography columns and NMR provides both real-time peak detection and chemical shift information for small aromatic molecules. These experiments demonstrate the unique power of magnetic resonance, both direct and remote, in studying chromatographic processes.

  3. Development of Monolithic Column Materials for the Separation and Analysis of Glycans

    Directory of Open Access Journals (Sweden)

    Allan J. Alla

    2015-02-01

    Full Text Available Monolithic column materials offer great advantages as chromatographic media in bioseparations and as solid-supports in biocatalysis. These single-piece porous materials have an interconnected ligament structure that limits the void volume inside the column, thus increasing the efficiency without sacrificing the permeability. The preparation of monolithic materials is easy, reproducible and has available a wide range of chemistries to utilize. Complex, heterogeneous and isobaric glycan structures require preparation methods that may include glycan release, separation and enrichment prior to a comprehensive and site-specific glycosylation analysis. Monolithic column materials aid that demand, as shown by the results reported by the research works presented in this review. These works include selective capture of glycans and glycoproteins via their interactions with lectins, boronic acids, hydrophobic, and hydrophilic/polar functional groups on monolith surfaces. It also includes immobilization of enzymes trypsin and PNGase F on monoliths to digest and deglycosylate glycoproteins and glycopeptides, respectively. The use of monolithic capillary columns for glycan separations through nano-liquid chromatography (nano-LC and capillary electrochromatography (CEC and coupling these columns to MS instruments to create multidimensional systems show the potential in the development of miniaturized, high-throughput and automated systems of glycan separation and analysis.

  4. Fabrication of interfacial functionalized porous polymer monolith and its adsorption properties of copper ions

    Energy Technology Data Exchange (ETDEWEB)

    Han, Jiaxi; Du, Zhongjie; Zou, Wei; Li, Hangquan; Zhang, Chen, E-mail: zhangch@mail.buct.edu.cn

    2014-07-15

    Highlights: • Interface functionalized PGMA porous monolith was fabricated. • The adsorption capacity of Cu{sup 2+} was 35.3 mg/g. • The effects of porous structure on the adsorption of Cu{sup 2+} were studied. • The adsorption behaviors of porous monolith were studied. - Abstract: The interfacial functionalized poly (glycidyl methacrylate) (PGMA) porous monolith was fabricated and applied as a novel porous adsorbent for copper ions (Cu{sup 2+}). PGMA porous material with highly interconnected pore network was prepared by concentrated emulsion polymerization template. Then polyacrylic acid (PAA) was grafted onto the interface of the porous monolith by the reaction between the epoxy group on PGMA and a carboxyl group on PAA. Finally, the porous monolith was interfacial functionalized by rich amount of carboxyl groups and could adsorb copper ions effectively. The chemical structure and porous morphology of the porous monolith were measured by Fourier transform infrared spectroscopy and scanning electron microscopy. Moreover, the effects of pore size distribution, pH value, co-existing ions, contacting time, and initial concentrations of copper ions on the adsorption capacity of the porous adsorbents were studied.

  5. Mineral resources of Antarctica

    Science.gov (United States)

    Compiled and edited by Wright, Nancy A.; Williams, Paul L.

    1974-01-01

    Although the existence of mineral deposits in Antarctica is highly probable, the chances of finding them are quite small. Minerals have been found there in great variety but only as occurrences. Manganese nodules, water (as ice), geothermal energy, coal, petroleum, and natural gas are potential resources that could perhaps be exploited in the future. On the basis of known mineral occurrences in Antarctica and relationships between geologic provinces of Antarctica and those of neighboring Gondwana continents, the best discovery probability for a base-metal deposit in any part of Antarctica is in the Andean orogen; it is estimated to be 0.075 (75 chances in 1,000).

  6. Evidence of Technetium and Iodine from a Sodalite-Bearing Ceramic Waste Form

    Energy Technology Data Exchange (ETDEWEB)

    Neeway, James J.; Qafoku, Nikolla; Williams, Benjamin D.; Snyder, Michelle MV; Brown, Christopher F.; Pierce, Eric M.

    2016-03-01

    Current plans for nuclear waste vitrification at the Hanford Tank Waste Treatment and Immobilization Plant (WTP) lack the capacity to treat all of the low activity waste (LAW) that is not encapsulated in the vitrified product. Several technologies are being considered to treat the excess LAW. One such technology is Fluidized Bed Steam Reforming (FBSR). The FBSR process results in a granular product composed of feldspathoid mineral phases that immobilize the major components in the LAW as well as other contaminants of concern (COCs), with Tc and I expected to be present in sodalite cages formed during the process. In order to meet compressive strength requirements at the Hanford Integrated Disposal Facility (IDF), the granular product may be encapsulated in a monolith. To demonstrate the ability of the technology to serve the mission of managing excess LAW, Single Pass Flow-Through (SPFT) tests have been performed on non-radioactive granular materials and granular materials encapsulated in a geopolymer binder produced at the engineering- and bench-scale as well as a granular product produced at the bench scale with actual Hanford tank waste. SPFT tests were conducted at 40 °C for durations up to 2 months with a flow-through solution buffered at pH 9. The forward reaction rate of the non-radioactive mineral product dissolution based on Si release for the granular product was measured to be (6.2 ± 2.1) × 10-4 g/m2d for the engineering-scale product and (13 ± 4.9) × 10-4 g/m2d for the bench-scale product. The resulting non-radioactive monoliths showed forward reaction rates based on Si release of (3.4 ± 1.1) × 10-4 g/m2d for the engineering-scale material and (4.2 ± 1.5) × 10-4 g/m2d for the bench-scale material demonstrating that encapsulation of the FBSR granular product in a monolith does not significantly alter the performance of the material. Finally, an FBSR granular product created at the bench scale using actual Hanford LAW gave similar release values

  7. FIBROUS MONOLITH WEAR RESISTANT COMPONENTS FOR THE MINING INDUSTRY

    Energy Technology Data Exchange (ETDEWEB)

    Mark J. Rigali

    2001-10-01

    Published mechanical and thermal properties data on a variety of materials was gathered, with focus on materials that have potential with respect to developing wear resistant and damage tolerant composite for mining industry applications. Preliminary core materials of interest include but are not limited to: Diamond, Tungsten Carbide and Cemented Tungsten Carbides, Carbides of Boron, Silicon, Titanium and Aluminum, Diboride of Titanium and Aluminum, Nitrides of Aluminum, Silicon, Titanium, and Boron, Aluminum Oxide, Tungsten, Titanium, Iron, Cobalt and Metal Alloys. Preliminary boundary materials of interest include but are not limited to: W metal, WC-Co, W-Co, WFeNi, and Mo metal and alloys. Several FM test coupons were fabricated with various compositions using the above listed materials. These coupons were consolidated to varying degrees by uniaxial hot pressing, then cut and ground to expose the FM cell structure. One promising system, WC-Co core and WFeNi boundary, was consolidated to 97% of theoretical density, and demonstrates excellent hardness. Data on standard mechanical tests was gathered, and tests will begin on the consolidated test coupons during the upcoming reporting period. The program statements of work for ACR Inc. and its subcontractors, as well as the final contract negotiations, were finalized during the current reporting period. The program start date was February 22nd, 2001. In addition to the current subcontractors, Kennametal Inc., a major manufacturer of cutting tools and wear resistant tooling for the mining industry, expressed considerable interest in ACR's Fibrous Monolith composites for both machine and mining applications. At the request of Kennametal, ARC Inc fabricated and delivered several Fibrous Monolith coupons and components for testing and evaluation in the mining and machine tool applications. Additional samples of Diamond/Tungsten Carbide-6%Cobalt Fibrous Monolith were fabricated and delivered for testing Kennametal

  8. [Synthetic mineral fibers].

    Science.gov (United States)

    Boillat, M A

    1999-03-27

    The group of man-made mineral fibres includes slagwool, glasswool, rockwool, glass filaments and microfibres, as well as refractory ceramic fibres. The toxicity of mineral fibres is determined by several factors such as the diameter (ceramic fibres. A slightly elevated standard mortality ratio for lung cancer has been documented in large cohorts of workers (USA, Europe and Canada) exposed to man-made mineral fibres, especially in the early technological phase. It is not possible to determine from these data whether the risk of lung cancer is due to the man-made mineral fibres themselves, in particular due to the lack of data on smoking habits. No increased risk of mesothelioma has been demonstrated in these cohorts. Epidemiological data are insufficient at this time concerning neoplastic diseases in refractory ceramic fibres.

  9. Minerals in environmental technology

    Energy Technology Data Exchange (ETDEWEB)

    Schuiling, R.D. [Utrecht Univ., Utrecht (Netherlands). Faculty of Earth Sciences

    2000-07-01

    Minerals play a key role in the environment; this role is often not well understood, because the emphasis of most environmentalists is on air, water, or the composition of solid wastes as a whole, without paying attention to their mineralogical composition. Several minerals can serve as effective and cheap adsorbents for many toxic chemicals. Several minerals can be used as a cheap substitute for expensive chemicals in environmental technologies. Environmental technologies that produce an economically interesting mineral will have an edge over competing technologies. Most of the problems, overreaction, panicky and expensive measures with regard to exposure from quartz and asbestos stem from a poor understanding of natural levels of common contaminants, a disregard for mineralogy, and a lack of insight into natural processes in general.

  10. sequenceMiner algorithm

    Data.gov (United States)

    National Aeronautics and Space Administration — Detecting and describing anomalies in large repositories of discrete symbol sequences. sequenceMiner has been open-sourced! Download the file below to try it out....

  11. Vitamins and Minerals

    Science.gov (United States)

    ... minerals your body needs. But if you're skipping meals, dieting, or if you're concerned that ... Kids For Parents MORE ON THIS TOPIC Healthy Breakfast Planner Nutrition & Fitness Center Vitamin D Figuring Out ...

  12. Mathematical model for bone mineralization

    Directory of Open Access Journals (Sweden)

    Svetlana V Komarova

    2015-08-01

    Full Text Available Defective bone mineralization has serious clinical manifestations, including deformities and fractures, but the regulation of this extracellular process is not fully understood. We have developed a mathematical model consisting of ordinary differential equations that describe collagen maturation, production and degradation of inhibitors, and mineral nucleation and growth. We examined the roles of individual processes in generating normal and abnormal mineralization patterns characterized using two outcome measures: mineralization lag time and degree of mineralization. Model parameters describing the formation of hydroxyapatite mineral on the nucleating centers most potently affected the degree of mineralization, while the parameters describing inhibitor homeostasis most effectively changed the mineralization lag time. Of interest, a parameter describing the rate of matrix maturation emerged as being capable of counter-intuitively increasing both the mineralization lag time and the degree of mineralization. We validated the accuracy of model predictions using known diseases of bone mineralization such as osteogenesis imperfecta and X-linked hypophosphatemia. The model successfully describes the highly non-linear mineralization dynamics, which includes an initial lag phase when osteoid is present but no mineralization is evident, then fast primary mineralization, followed by secondary mineralization characterized by a continuous slow increase in bone mineral content. The developed model can potentially predict the function for a mutated protein based on the histology of pathologic bone samples from mineralization disorders of unknown etiology.

  13. Steam reforming of n-hexane on pellet and monolithic catalyst beds. A comparative study on improvements due to heat transfer

    Science.gov (United States)

    1981-01-01

    Monolithic catalysts with higher available active surface areas and better thermal conductivity than conventional pellets beds, making possible the steam reforming of fuels heavier than naphtha, were examined. Performance comparisons were made between conventional pellet beds and honeycomb monolith catalysts using n-hexane as the fuel. Metal-supported monoliths were examined. These offer higher structural stability and higher thermal conductivity than ceramic supports. Data from two metal monoliths of different nickel catalyst loadings were compared to pellets under the same operating conditions. Improved heat transfer and better conversion efficiencies were obtained with the monolith having higher catalyst loading. Surface-gas interaction was observed throughout the length of the monoliths.

  14. A Differential Monolithically Integrated Inductive Linear Displacement Measurement Microsystem

    Directory of Open Access Journals (Sweden)

    Matija Podhraški

    2016-03-01

    Full Text Available An inductive linear displacement measurement microsystem realized as a monolithic Application-Specific Integrated Circuit (ASIC is presented. The system comprises integrated microtransformers as sensing elements, and analog front-end electronics for signal processing and demodulation, both jointly fabricated in a conventional commercially available four-metal 350-nm CMOS process. The key novelty of the presented system is its full integration, straightforward fabrication, and ease of application, requiring no external light or magnetic field source. Such systems therefore have the possibility of substituting certain conventional position encoder types. The microtransformers are excited by an AC signal in MHz range. The displacement information is modulated into the AC signal by a metal grating scale placed over the microsystem, employing a differential measurement principle. Homodyne mixing is used for the demodulation of the scale displacement information, returned by the ASIC as a DC signal in two quadrature channels allowing the determination of linear position of the target scale. The microsystem design, simulations, and characterization are presented. Various system operating conditions such as frequency, phase, target scale material and distance have been experimentally evaluated. The best results have been achieved at 4 MHz, demonstrating a linear resolution of 20 µm with steel and copper scale, having respective sensitivities of 0.71 V/mm and 0.99 V/mm.

  15. Monolithic oxide-metal composite thermoelectric generators for energy harvesting

    Science.gov (United States)

    Funahashi, Shuichi; Nakamura, Takanori; Kageyama, Keisuke; Ieki, Hideharu

    2011-06-01

    Monolithic oxide-metal composite thermoelectric generators (TEGs) were fabricated using multilayer co-fired ceramic technology. These devices consisted of Ni0.9Mo0.1 and La0.035Sr0.965TiO3 as p- and n-type thermoelectric materials, and Y0.03Zr0.97O2 was used as an insulator, sandwiched between p- and n-type layers. To co-fire dissimilar materials, p-type layers contained 20 wt. % La0.035Sr0.965TiO3; thus, these were oxide-metal composite layers. The fabricated device had 50 pairs of p-i-n junctions of 5.9 mm × 7.0 mm × 2.6 mm. The calculated maximum value of the electric power output from the device was 450 mW/cm2 at ΔT = 360 K. Furthermore, this device generated 100 μW at ΔT = 10 K and operated a radio frequency (RF) transmitter circuit module assumed to be a sensor network system.

  16. III-nitride monolithic LED covering full RGB color gamut

    Science.gov (United States)

    El-Ghoroury, Hussein S.; Chuang, Chih-Li; Kisin, Mikhail V.

    2016-03-01

    We present numerical simulation of III-nitride monolithic multi-color LED covering full red-green-blue (RGB) color gamut. The RGB LED structure was grown at Ostendo Technologies Inc. and has been used in Ostendo proprietary Quantum Photonic Imager (QPI) device. Active region of our RGB LED incorporates specially designed intermediate carrier blocking layers (ICBLs) controlling transport of each type of carriers and subsequent carrier injection redistribution among the optically active quantum wells (QWs) with different emission wavelengths. ICBLs are proved to be essential elements of multi-color LED active region design requiring optimization both in material composition and doping level. Strong interdependence between ICBL parameters and active QW characteristics presents additional challenge to multi-color LED design. Combination of several effects was crucial for adequate simulation of RGB LED color control features. Standard drift-diffusion transport model has been appended with rate equations for dynamic QW-confined carrier populations which appear severely off-balanced from corresponding mobile carrier subsystems. QW overshoot and Auger-assisted QW depopulation were also included into the carrier kinetic model thus enhancing the non-equilibrium character of QW confined populations and supporting the mobile carrier transport across the MQW active region. For device simulation we use COMSOL-based program suit developed at Ostendo Technologies Inc.

  17. A Differential Monolithically Integrated Inductive Linear Displacement Measurement Microsystem.

    Science.gov (United States)

    Podhraški, Matija; Trontelj, Janez

    2016-03-17

    An inductive linear displacement measurement microsystem realized as a monolithic Application-Specific Integrated Circuit (ASIC) is presented. The system comprises integrated microtransformers as sensing elements, and analog front-end electronics for signal processing and demodulation, both jointly fabricated in a conventional commercially available four-metal 350-nm CMOS process. The key novelty of the presented system is its full integration, straightforward fabrication, and ease of application, requiring no external light or magnetic field source. Such systems therefore have the possibility of substituting certain conventional position encoder types. The microtransformers are excited by an AC signal in MHz range. The displacement information is modulated into the AC signal by a metal grating scale placed over the microsystem, employing a differential measurement principle. Homodyne mixing is used for the demodulation of the scale displacement information, returned by the ASIC as a DC signal in two quadrature channels allowing the determination of linear position of the target scale. The microsystem design, simulations, and characterization are presented. Various system operating conditions such as frequency, phase, target scale material and distance have been experimentally evaluated. The best results have been achieved at 4 MHz, demonstrating a linear resolution of 20 µm with steel and copper scale, having respective sensitivities of 0.71 V/mm and 0.99 V/mm.

  18. A Differential Monolithically Integrated Inductive Linear Displacement Measurement Microsystem

    Science.gov (United States)

    Podhraški, Matija; Trontelj, Janez

    2016-01-01

    An inductive linear displacement measurement microsystem realized as a monolithic Application-Specific Integrated Circuit (ASIC) is presented. The system comprises integrated microtransformers as sensing elements, and analog front-end electronics for signal processing and demodulation, both jointly fabricated in a conventional commercially available four-metal 350-nm CMOS process. The key novelty of the presented system is its full integration, straightforward fabrication, and ease of application, requiring no external light or magnetic field source. Such systems therefore have the possibility of substituting certain conventional position encoder types. The microtransformers are excited by an AC signal in MHz range. The displacement information is modulated into the AC signal by a metal grating scale placed over the microsystem, employing a differential measurement principle. Homodyne mixing is used for the demodulation of the scale displacement information, returned by the ASIC as a DC signal in two quadrature channels allowing the determination of linear position of the target scale. The microsystem design, simulations, and characterization are presented. Various system operating conditions such as frequency, phase, target scale material and distance have been experimentally evaluated. The best results have been achieved at 4 MHz, demonstrating a linear resolution of 20 µm with steel and copper scale, having respective sensitivities of 0.71 V/mm and 0.99 V/mm. PMID:26999146

  19. Synthesis of monolithic graphene – graphite integrated electronics

    Science.gov (United States)

    Park, Jang-Ung; Nam, SungWoo; Lee, Mi-Sun; Lieber, Charles M.

    2013-01-01

    Encoding electronic functionality into nanoscale elements during chemical synthesis has been extensively explored over the past decade as the key to developing integrated nanosystems1 with functions defined by synthesis2-6. Graphene7-12 has been recently explored as a two-dimensional nanoscale material, and has demonstrated simple device functions based on conventional top-down fabrication13-20. However, the synthetic approach to encoding electronic functionality and thus enabling an entire integrated graphene electronics in a chemical synthesis had not previously been demonstrated. Here we report an unconventional approach for the synthesis of monolithically-integrated electronic devices based on graphene and graphite. Spatial patterning of heterogeneous catalyst metals permits the selective growth of graphene and graphite, with controlled number of graphene layers. Graphene transistor arrays with graphitic electrodes and interconnects were formed from synthesis. These functional, all-carbon structures were transferrable onto a variety of substrates. The integrated transistor arrays were used to demonstrate real-time, multiplexed chemical sensing, and more significantly, multiple carbon layers of the graphene-graphite device components were vertically assembled to form a three-dimensional flexible structure which served as a top-gate transistor array. These results represent a substantial progress towards encoding electronic functionality via chemical synthesis and suggest future promise for one-step integration of graphene-graphite based electronics. PMID:22101813

  20. Synthesis of monolithic graphene-graphite integrated electronics.

    Science.gov (United States)

    Park, Jang-Ung; Nam, SungWoo; Lee, Mi-Sun; Lieber, Charles M

    2011-11-20

    Encoding electronic functionality into nanoscale elements during chemical synthesis has been extensively explored over the past decade as the key to developing integrated nanosystems with functions defined by synthesis. Graphene has been recently explored as a two-dimensional nanoscale material, and has demonstrated simple device functions based on conventional top-down fabrication. However, the synthetic approach to encoding electronic functionality and thus enabling an entire integrated graphene electronics in a chemical synthesis had not previously been demonstrated. Here we report an unconventional approach for the synthesis of monolithically integrated electronic devices based on graphene and graphite. Spatial patterning of heterogeneous metal catalysts permits the selective growth of graphene and graphite, with a controlled number of graphene layers. Graphene transistor arrays with graphitic electrodes and interconnects were formed from the synthesis. These functional, all-carbon structures were transferable onto a variety of substrates. The integrated transistor arrays were used to demonstrate real-time, multiplexed chemical sensing and more significantly, multiple carbon layers of the graphene-graphite device components were vertically assembled to form a three-dimensional flexible structure which served as a top-gate transistor array. These results represent substantial progress towards encoding electronic functionality through chemical synthesis and suggest the future promise of one-step integration of graphene-graphite based electronics.

  1. Monolithic subwavelength high refractive-index-contrast grating VCSELs

    Science.gov (United States)

    Gebski, Marcin; Dems, Maciej; Lott, James A.; Czyszanowski, Tomasz

    2016-03-01

    In this paper we present optical design and simulation results of vertical-cavity surface-emitting lasers (VCSELs) that incorporate monolithic subwavelength high refractive-index-contrast grating (MHCG) mirrors - a new variety of HCG mirror that is composed of high index material surrounded only on one side by low index material. We show the impact of an MHCG mirror on the performance of 980 nm VCSELs designed for high bit rate and energy-efficient optical data communications. In our design, all or part of the all-semiconductor top coupling distributed Bragg reflector mirror is replaced by an undoped gallium-arsenide MHCG. We show how the optical field intensity distribution of the VCSEL's fundamental mode is controlled by the combination of the number of residual distributed Bragg reflector (DBR) mirror periods and the physical design of the topmost gallium-arsenide MHCG. Additionally, we numerically investigate the confinement factors of our VCSELs and show that this parameter for the MHCG DBR VCSELs may only be properly determined in two or three dimensions due to the periodic nature of the grating mirror.

  2. A symmetric positive definite formulation for monolithic fluid structure interaction

    KAUST Repository

    Robinson-Mosher, Avi

    2011-02-01

    In this paper we consider a strongly coupled (monolithic) fluid structure interaction framework for incompressible flow, as opposed to a loosely coupled (partitioned) method. This requires solving a single linear system that combines the unknown velocities of the structure with the unknown pressures of the fluid. In our previous work, we were able to obtain a symmetric formulation of this coupled system; however, it was also indefinite, making it more difficult to solve. In fact in practice there have been cases where we have been unable to invert the system. In this paper we take a novel approach that consists of factoring the damping matrix of deformable structures and show that this can be used to obtain a symmetric positive definite system, at least to the extent that the uncoupled systems were symmetric positive definite. We use a traditional MAC grid discretization of the fluid and a fully Lagrangian discretization of the structures for the sake of exposition, noting that our procedure can be generalized to other scenarios. For the special case of rigid bodies, where there are no internal damping forces, we exactly recover the system of Batty et al. (2007) [4]. © 2010 Elsevier Inc.

  3. Sausage Waves in Transversely Nonuniform Monolithic Coronal Tubes

    Science.gov (United States)

    Lopin, I.; Nagorny, I.

    2015-09-01

    We investigate fast sausage waves in a monolithic coronal magnetic tube, modeled as a local density inhomogeneity with a continuous radial profile. This work is a natural extension of our previous results, obtained for a slab loop model for the case of cylindrical geometry. Using Kneser’s oscillating theorem, we provided the criteria for the existence of trapped and leaky wave regimes as a function of the profile features. For a number of density profiles there are only trapped modes for the entire range of longitudinal wave numbers. The phase speed of these modes tends toward the external Alfvén speed in the long wavelength limit. The generalized results were supported by the analytic solution of the wave equation for the specific density profiles. The approximate Wentzel-Kramers-Brillouin solutions allowed us to obtain the desired dispersion relations and to study their properties as a function of the profile parameters. The multicomponent quasi-periodic pulsations in flaring loops, observed on 2001 May 2 and 2002 July 3, are interpreted in terms of the transversely fundamental trapped fast sausage mode with several longitudinal harmonics in a smooth coronal waveguide.

  4. The mineral economy of Brazil--Economia mineral do Brasil

    Science.gov (United States)

    Gurmendi, Alfredo C.; Barboza, Frederico Lopes; Thorman, Charles H.

    1999-01-01

    This study depicts the Brazilian government structure, mineral legislation and investment policy, taxation, foreign investment policies, environmental laws and regulations, and conditions in which the mineral industry operates. The report underlines Brazil's large and diversified mineral endowment. A total of 37 mineral commodities, or groups of closely related commodities, is discussed. An overview of the geologic setting of the major mineral deposits is presented. This report is presented in English and Portuguese in pdf format.

  5. Measuring the Hardness of Minerals

    Science.gov (United States)

    Bushby, Jessica

    2005-01-01

    The author discusses Moh's hardness scale, a comparative scale for minerals, whereby the softest mineral (talc) is placed at 1 and the hardest mineral (diamond) is placed at 10, with all other minerals ordered in between, according to their hardness. Development history of the scale is outlined, as well as a description of how the scale is used…

  6. Monolithic stationary phases with incorporated fumed silica nanoparticles. Part I. Polymethacrylate-based monolithic column with incorporated bare fumed silica nanoparticles for hydrophilic interaction liquid chromatography.

    Science.gov (United States)

    Aydoğan, Cemil; El Rassi, Ziad

    2016-05-01

    Fumed silica nanoparticles (FSNPs), were incorporated for the first time into a polymethacrylate monolithic column containing glyceryl monomethacrylate (GMM) and ethylene dimethacrylate (EDMA) in order to develop a new monolithic column for hydrophilic interaction high performance liquid chromatography (HILIC). When compared to poly(GMM-EDMA) monolithic column without FSNPs, the same monolithic column with incorporated FSNPs yielded important effects on HILIC separations. The effects of monomers and FSNPs content of the polymerization mixture on the performance of the monolithic column were examined in details, and the optimized stationary phase was investigated over a wide range of mobile phase composition with polar acidic, weakly basic and neutral analytes including hydroxy benzoic acids, nucleotides, nucleosides, dimethylformamide, formamide and thiourea. The retention of these analytes was mainly controlled by hydrophilic interactions with the FSNPs and electrostatic repulsion from the negatively charged silica surface in the case of hydroxy benzoic acids and nucleotides. The electrostatic repulsion was minimized by decreasing the pH of the aqueous component of the mobile phase, which in turn enhanced the retention of acidic solutes. Nucleotides were best separated using step gradient elution at decreasing pH as well as ACN concentration in the mobile phase. Improved peak shape and faster analysis of nucleosides were attained by a fast linear gradient elution with a shallow decrease in the ACN content of the ACN-rich mobile phase. The run-to-run and column-to-column reproducibility were satisfactory. The percent relative standard deviations (%RSDs) for the retention times of tested solutes were lower than 2.5% under isocratic conditions and lower than 3.5 under gradient conditions.

  7. Monolithic stationary phases with incorporated fumed silica nanoparticles. Part II. Polymethacrylate-based monolithic column with "covalently" incorporated modified octadecyl fumed silica nanoparticles for reversed-phase chromatography.

    Science.gov (United States)

    Aydoğan, Cemil; El Rassi, Ziad

    2016-05-01

    This study is concerned with the incorporation of surface modified fumed silica nanoparticles (FSNPs) into polymethacrylate based monolithic columns for use in reversed phase chromatography (RPC) of small solutes and proteins. First, FSNPs were modified with 3-(trimethoxysilyl)propylmethacrylate (TMSPM) to yield the "hybrid" methacryloyl fumed silica nanoparticle (MFSNP) monomer. The resulting MFSNP was then mixed with glyceryl monomethacrylate (GMM) and ethylene dimethacrylate (EDMA) in a binary porogenic solvent composed of cyclohexanol and dodecanol, and the in situ copolymerization of MFSNP, GMM and EDMA was performed in a stainless steel column of 4.6 mm i.d. The silanol groups of the hybrid monolith thus obtained were grafted with octadecyl ligands by perfusing the hybrid monolithic column with a solution of 4% w/v of dimethyloctadecylchlorosilane (DODCS) in toluene while the column was maintained at 110°C for 6h (in a heated HPLC oven). One of the originalities of this study was to demonstrate MFSNP as a novel derivatized "hybrid monomer" in making RPC monolithic columns with surface bound octadecyl ligands. In this respect, the RPC behavior of the monolithic column with "covalently" incorporated FNSPs having surface grafted octadecyl ligands was evaluated with alkylbenzenes, aniline derivatives and phenolic compounds. The results showed that the hybrid poly(GMA-EDMA-MFSNP) having surface bound octadecyl ligands exhibited hydrophobic interactions under reversed phase elution conditions. Furthermore, six standard proteins were baseline separated on the column using a 10min linear gradient elution at increasing ACN concentration in the mobile phase at a flow rate of 1.0mL/min using a 10 cm×4.6mm i.d. column. The relative standard deviations (RSDs) for the retention times of the tested solutes were lower than 2.1% and 2.4% under isocratic elution and gradient elution conditions, respectively.

  8. Extraterrestrial magnetic minerals

    Science.gov (United States)

    Pechersky, D. M.; Markov, G. P.; Tsel'movich, V. A.; Sharonova, Z. V.

    2012-07-01

    Thermomagnetic and microprobe analyses are carried out and a set of magnetic characteristics are measured for 25 meteorites and 3 tektites from the collections of the Vernadsky Geological Museum of the Russian Academy of Sciences and Museum of Natural History of the North-East Interdisciplinary Science Research Institute, Far Eastern Branch of the Russian Academy of Sciences. It is found that, notwithstanding their type, all the meteorites contain the same magnetic minerals and only differ by concentrations of these minerals. Kamacite with less than 10% nickel is the main magnetic mineral in the studied samples. Pure iron, taenite, and schreibersite are less frequent; nickel, various iron spinels, Fe-Al alloys, etc., are very rare. These minerals are normally absent in the crusts of the Earth and other planets. The studied meteorites are more likely parts of the cores and lower mantles of the meteoritic parent bodies (the planets). Uniformity in the magnetic properties of the meteorites and the types of their thermomagnetic (MT) curves is violated by secondary alterations of the meteorites in the terrestrial environment. The sediments demonstrate the same monotony as the meteorites: kamacite is likely the only extraterrestrial magnetic mineral, which is abundant in sediments and associated with cosmic dust. The compositional similarity of kamacite in iron meteorites and in cosmic dust is due to their common source; the degree of fragmentation of the material of the parent body is the only difference.

  9. Thorium in mineral products.

    Science.gov (United States)

    Collier, D E; Brown, S A; Blagojevic, N; Soldenhoff, K H; Ring, R J

    2001-01-01

    Many ores contain low levels of thorium. When these ores are processed, the associated radioactivity can be found in mineral concentrates, intermediates and final products. There is an incentive for industries to remove radioactivity from mineral products to allow the movement and sale of these materials, both nationally and internationally, without the need for licensing. Control of thorium in various products involves the development and optimisation of process steps to be able to meet product specifications. The Australian Nuclear Science and Technology Organisation (ANSTO) has undertaken a range of R & D programmes targeting the treatment of thorium-bearing minerals. This paper discusses the application of a microprobe technique for siting radioactivity in zircon and ilmenite and the problems experienced in measuring the concentrations in solid rare earth products.

  10. Influence of the preparation design and artificial aging on the fracture resistance of monolithic zirconia crowns

    Science.gov (United States)

    Anastassova-Yoshida, Yana; Nothdurft, Frank Phillip; von See, Constantin; Pospiech, Peter

    2016-01-01

    PURPOSE The aim of this study was to evaluate the fracture resistance and fracture behavior of monolithic zirconia crowns in accordance with the preparation design and aging simulation method. MATERIALS AND METHODS An upper first molar was prepared sequentially with three different preparation designs: shoulderless preparation, 0.4 mm chamfer and 0.8 mm chamfer preparation. For each preparation design, 30 monolithic zirconia crowns were fabricated. After cementation on Cr-Co alloy dies, the following artificial aging procedures were performed: (1) thermal cycling and mechanical loading (TCML): 5000 cycles of thermal cycling 5℃–55℃ and chewing simulation (1,200,000 cycles, 50 N); (2) Low Temperature Degradation simulation (LTD): autoclave treatment at 137℃, 2 bar for 3 hours and chewing simulation; and (3) no pre-treatment (control group). After artificial aging, the crowns were loaded until fracture. RESULTS The mean values of fracture resistance varied between 3414 N (LTD; 0.8 mm chamfer preparation) and 5712 N (control group; shoulderless preparation). Two-way ANOVA analysis showed a significantly higher fracture loads for the shoulderless preparation, whereas no difference was found between the chamfer preparations. In contrast to TCML, after LTD simulation the fracture strength of monolithic zirconia crowns decreased significantly. CONCLUSION The monolithic crowns tested in this study showed generally high fracture load values. Preparation design and LTD simulation had a significant influence on the fracture strength of monolithic zirconia crowns. PMID:26949485

  11. Surface characteristics and antibacterial activity of a silver-doped carbon monolith

    Directory of Open Access Journals (Sweden)

    Marija Vukčević et al

    2008-01-01

    Full Text Available A carbon monolith with a silver coating was prepared and its antimicrobial behaviour in a flow system was examined. The functional groups on the surface of the carbon monolith were determined by temperature-programmed desorption and Boehm's method, and the point of zero charge was determined by mass titration. The specific surface area was examined by N2 adsorption using the Brunauer, Emmett and Teller (BET method. As a test for the surface activity, the deposition of silver from an aqueous solution of a silver salt was used. The morphology and structure of the silver coatings were characterized by scanning electron microscopy and x-ray diffraction. The resistance to the attrition of the silver deposited on the carbon monolith was tested. The antimicrobial activity of the carbon monolith with a silver coating was determined using standard microbiological methods. Carbon monolith samples with a silver coating showed good antimicrobial activity against Escherichia coli, Staphylococcus aureus and Candida albicans, and are therefore suitable for water purification, particularly as personal disposable water filters with a limited capacity.

  12. Solvers for large-displacement fluid structure interaction problems: segregated versus monolithic approaches

    Science.gov (United States)

    Heil, Matthias; Hazel, Andrew L.; Boyle, Jonathan

    2008-12-01

    We compare the relative performance of monolithic and segregated (partitioned) solvers for large- displacement fluid structure interaction (FSI) problems within the framework of oomph-lib, the object-oriented multi-physics finite-element library, available as open-source software at http://www.oomph-lib.org . Monolithic solvers are widely acknowledged to be more robust than their segregated counterparts, but are believed to be too expensive for use in large-scale problems. We demonstrate that monolithic solvers are competitive even for problems in which the fluid solid coupling is weak and, hence, the segregated solvers converge within a moderate number of iterations. The efficient monolithic solution of large-scale FSI problems requires the development of preconditioners for the iterative solution of the linear systems that arise during the solution of the monolithically coupled fluid and solid equations by Newton’s method. We demonstrate that recent improvements to oomph-lib’s FSI preconditioner result in mesh-independent convergence rates under uniform and non-uniform (adaptive) mesh refinement, and explore its performance in a number of two- and three-dimensional test problems involving the interaction of finite-Reynolds-number flows with shell and beam structures, as well as finite-thickness solids.

  13. Monolithic precolumns as efficient tools for guiding the design of nanoparticulate drug-delivery formulations.

    Science.gov (United States)

    Gatschelhofer, Christina; Prasch, Agnes; Buchmeiser, Michael R; Zimmer, Andreas; Wernig, Karin; Griesbacher, Martin; Pieber, Thomas R; Sinner, Frank M

    2012-09-01

    The development of nanomedicines for improved diagnosis and treatment of diseases is pushing current analytical methods to their limits. More efficient, quantitative high-throughput screening methods are needed to guide the optimization of promising nanoparticulate drug delivery formulations. In response to this need, we present herein a novel approach using monolithic separation media. The unique porosity of our capillary monolithic precolumns allows the direct injection and online removal of protamine-oligonucleotide nanoparticles ("proticles") without column clogging, thus avoiding the need for time-consuming off-line sample workup. Furthermore, ring-opening metathesis polymerization (ROMP)-derived monoliths show equivalent preconcentration efficiency for the target drug vasoactive intestinal peptide (VIP) as conventional particle-packed precolumns. The performance of the ROMP-derived monolithic precolumns was constant over at least 100 injections of crude proticle-containing and 300 injections of highly acidic samples. Applying a validated LC-MS/MS capillary monolithic column switching method, we demonstrate the rapid determination of both drug load and in vitro drug release kinetics of proticles within the critical first 2 h and investigate the stability of VIP-loaded proticles in aqueous storage medium intended for inhalation therapy.

  14. Comparison of Membrane Chromatography and Monolith Chromatography for Lactoferrin and Bovine Serum Albumin Separation

    Directory of Open Access Journals (Sweden)

    Chalore Teepakorn

    2016-09-01

    Full Text Available These last few decades, membranes and monoliths have been increasingly used as stationary phases for chromatography. Their fast mass transfer is mainly based on convection, which leads to reduced diffusion, which is usually observed in resins. Nevertheless, poor flow distribution, which causes inefficient binding, remains a major challenge for the development of both membrane and monolith devices. Moreover, the comparison of membranes and monoliths for biomolecule separation has been very poorly investigated. In this paper, the separation of two proteins, bovine serum albumin (BSA and lactoferrin (LF, with similar sizes, but different isoelectric points, was investigated at a pH of 6.0 with a BSA-LF concentration ratio of 2/1 (2.00 mg·mL−1 BSA and 1.00 mg·mL−1 LF solution using strong cation exchange membranes and monoliths packed in the same housing, as well as commercialized devices. The feeding flow rate was operated at 12.0 bed volume (BV/min for all devices. Afterward, bound LF was eluted using a phosphate-buffered saline solution with 2.00 M NaCl. Using membranes in a CIM housing from BIA Separations (Slovenia with porous frits before and after the membrane bed, higher binding capacities, sharper breakthrough curves, as well as sharper and more symmetric elution peaks were obtained. The monolith and commercialized membrane devices showed lower LF binding capacity and broadened and non-symmetric elution peaks.

  15. A monolithic lipase reactor for biodiesel production by transesterification of triacylglycerides into fatty acid methyl esters

    KAUST Repository

    Urban, Jiří T.

    2011-09-26

    An enzymatic reactor with lipase immobilized on a monolithic polymer support has been prepared and used to catalyze the transesterification of triacylglycerides into the fatty acid methyl esters commonly used for biodiesel. A design of experiments procedure was used to optimize the monolithic reactor with variables including control of the surface polarity of the monolith via variations in the length of the hydrocarbon chain in alkyl methacrylate monomer, time of grafting of 1-vinyl-4,4-dimethylazlactone used to activate the monolith, and time used for the immobilization of porcine lipase. Optimal conditions involved the use of a poly(stearyl methacrylate-co-ethylene dimethacrylate) monolith, grafted first with vinylazlactone, then treated with lipase for 2h to carry out the immobilization of the enzyme. Best conditions for the transesterification of glyceryl tributyrate included a temperature of 37°C and a 10min residence time of the substrate in the bioreactor. The reactor did not lose its activity even after pumping through it a solution of substrate equaling 1,000 reactor volumes. This enzymatic reactor was also used for the transesterification of triacylglycerides from soybean oil to fatty acid methyl esters thus demonstrating the ability of the reactor to produce biodiesel. © 2011 Wiley Periodicals, Inc.

  16. High pressure-resistant SU-8 microchannels for monolithic porous structure integration

    Science.gov (United States)

    Carlier, Julien; Chuda, Katarzyna; Arscott, Steve; Thomy, Vincent; Verbeke, Bernard; Coqueret, Xavier; Camart, Jean Christophe; Druon, Christian; Tabourier, Pierre

    2006-10-01

    Integrated lab-on-chip (LOC) microsystems dedicated to proteomic analysis require specific pretreatment steps such as protein trypsic digestion, concentration, desalting or separation of biological samples. These steps can be achieved thanks to porous monolithic polymers. This paper deals with the integration of such a polymer into SU-8 microchannels by using a multi-material technology (SU-8, Pyrex and silicon). A solution for the fabrication of complete polymer microchannels which are high pressure- and solvents-resistant is proposed. This technique uses the negative photoresist SU-8 which is compatible with the protein analysis performed here. Our process requires a novel technological step using a silane coupling agent. This modification of the SU-8/Pyrex interface leads to the fabrication of a 100 µm × 160 µm section microchannel (length of 3 cm), closed with a Pyrex® lid by SU-8 bonding resistant to 80 bar. An improvement of the SU-8/monolithic structure is also demonstrated thanks to a specific treatment of the polymer enabling good anchoring of the monolith in the microchannels, and the pressure-resistance tests were also achieved with the monolithic structure integrated in the microchannels. A digestion step of a protein sample of benzoylarginine ethyl ester in a SU-8 microchannel was achieved after the functionalization of a monolith anchored in the microchannel. Analysis by UV/VIS spectroscopy of this in situ digestion has been reported.

  17. β-Cyclodextrin functionalized polystyrene porous monoliths for separating phenol from wastewater.

    Science.gov (United States)

    Han, Jiaxi; Xie, Kaijun; Du, Zhongjie; Zou, Wei; Zhang, Chen

    2015-04-20

    A β-cyclodextrin (β-CD) functionalized polystyrene porous monolith was prepared by the following procedure: First, β-CD was modified with allyl bromide leading to allyl-β-cyclodextrin (allyl-β-CD); then a concentrated emulsion was prepared using a mixture of allyl-β-CD, styrene, and divinyl benzene as the continuous phase and water as the dispersed phase. In the third step, a β-cyclodextrin (β-CD) functionalized polystyrene porous monolith was obtained by copolymerization of allyl-β-CD and styrene followed by removal of the water phase. Since the allyl-β-CD contained both hydrophilic and hydrophobic groups, it tended to move towards the water/oil interface. As a result, the internal surfaces of the porous monolith were enriched with β-CD. This enrichment was indicated by X-ray photoelectron spectroscopy characterization. The high content of β-CD and the high specific surface area of the porous monolith both contributed to a high adsorption capacity. For example, the maximum adsorption of phenol was 5.74 mg/g. Importantly, the porous monolith could be easily regenerated and recycled through desorption with ethanol and it was found that the adsorption properties remained stable for at least five adsorption/desorption cycles. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. Facile synthesis of gradient mesoporous carbon monolith based on polymerization-induced phase separation

    Science.gov (United States)

    Xu, Shunjian; Luo, Yufeng; Zhong, Wei; Xiao, Zonghu; Luo, Yongping; Ou, Hui; Zhao, Xing-Zhong

    2014-06-01

    In this paper, a gradient mesoporous carbon (GMC) monolith derived from the mixtures of phenolic resin (PF) and ethylene glycol (EG) was prepared by a facile route based on polymerization-induced phase separation under temperature gradient (TG). A graded biphasic structure of PF-rich and EG-rich phases was first formed in preform under a TG, and then the preform was pyrolyzed to obtain the GMC monolith. The TG is mainly induced by the thermal resistance of the preferential phase separation layer at high temperature region. The pore structure of the monolith changes gradually along the TG direction. When the TG varies from 58°C to 29°C, the pore size, apparent porosity and specific surface area of the monolith range respectively from 18 nm to 83 nm, from 32% to 39% and from 140.5 m2/g to 515.3 m2/g. The gradient porous structure of the monolith is inherited from that of the preform, which depends on phase separation under TG in the resin mixtures. The pyrolysis mainly brings about the contraction of the pore size and wall thickness as well as the transformation of polymerized PF into glassy carbon.

  19. A monolithic lipase reactor for biodiesel production by transesterification of triacylglycerides into fatty acid methyl esters.

    Science.gov (United States)

    Urban, Jiri; Svec, Frantisek; Fréchet, Jean M J

    2012-02-01

    An enzymatic reactor with lipase immobilized on a monolithic polymer support has been prepared and used to catalyze the transesterification of triacylglycerides into the fatty acid methyl esters commonly used for biodiesel. A design of experiments procedure was used to optimize the monolithic reactor with variables including control of the surface polarity of the monolith via variations in the length of the hydrocarbon chain in alkyl methacrylate monomer, time of grafting of 1-vinyl-4,4-dimethylazlactone used to activate the monolith, and time used for the immobilization of porcine lipase. Optimal conditions involved the use of a poly(stearyl methacrylate-co-ethylene dimethacrylate) monolith, grafted first with vinylazlactone, then treated with lipase for 2 h to carry out the immobilization of the enzyme. Best conditions for the transesterification of glyceryl tributyrate included a temperature of 37°C and a 10 min residence time of the substrate in the bioreactor. The reactor did not lose its activity even after pumping through it a solution of substrate equaling 1,000 reactor volumes. This enzymatic reactor was also used for the transesterification of triacylglycerides from soybean oil to fatty acid methyl esters thus demonstrating the ability of the reactor to produce biodiesel.

  20. Development of an epoxy-based monolith used for the affinity capturing of Escherichia coli bacteria.

    Science.gov (United States)

    Peskoller, Caroline; Niessner, Reinhard; Seidel, Michael

    2009-05-01

    An epoxy-based monolith has been developed for use as hydrophilic support in bioseparation. This monolith is produced by self-polymerization of polyglycerol-3-glycidyl ether in organic solvents as porogens at room temperature within 1 h. One receives a highly cross-linked structure that provides useful mechanical properties. The porosity and pore diameter can be controlled by varying the composition of the porogen. In this work, an epoxy-based monolith with a high porosity (79%) and large pore size (22 microm) is prepared and used in affinity capturing of bacterial cells. These features allow the passage of bacterial cells through the column. As affinity ligand polymyxin B is used, which allows the binding of gram-negative bacteria. The efficiency of the monolithic affinity column is studied with Escherichia coli spiked in water. Bacterial cells are concentrated on the column at pH 4 and eluted with a recovery of 97+/-3% in 200 microL by changing the pH value without impairing viability of bacteria. The dynamic capacity for the monolithic column is nearly independent of the flow rate (4x10(9)cells/column). Thereby, it is possible to separate and enrich gram-negative bacterial cells, such as E. coli, with high flow rates (10 mL/min) and low back pressure (<1 bar) in a volume as low as 200 microL compatible for real-time polymerase chain reaction, microarray formats, and biosensors.

  1. Extraction of genomic DNA using a new amino silica monolithic column.

    Science.gov (United States)

    Liu, Lijia; Yu, Shengbing; Yang, Shuixian; Zhou, Ping; Hu, Jiming; Zhang, Yibing

    2009-08-01

    A new amino silica monolithic column was developed for DNA extraction in a miniaturized format. The monolithic column was prepared in situ by polymerization of tetraethoxysilane (TEOS) and N-(beta-aminoethyl)-gamma-aminopropylmethyldimethoxysilane (AEAPMDMS). DNA was loaded in 50 mM tris(hydroxylmethyl)aminomethane-EDTA buffer at pH 7.0 and eluted with 300 mM potassium phosphate solution at pH 10.0. Under optimal condition, a 6.0-cm monolithic column provided a capacity of 56 ng DNA with an extraction efficiency of 71 +/- 5.2% (X +/- RSD). When the amino silica monolithic column was applied to extract genomic DNA from the whole blood of crucian carp, an extraction efficiency of 52 +/- 5.6% (X +/- RSD) was obtained by three extractions. Since the chaotropic-based sample loading and organic solvent wash steps were avoided in this procedure, the purified DNA was suitable for downstream processes such as PCR. This amino silica monolithic column was demonstrated to allow rapid and efficient DNA purification in microscale.

  2. Recent Advances and Uses of Monolithic Columns for the Analysis of Residues and Contaminants in Food

    Directory of Open Access Journals (Sweden)

    Mónica Díaz-Bao

    2015-02-01

    Full Text Available Monolithic columns are gaining interest as excellent substitutes to conventional particle-packed columns. These columns show higher permeability and lower flow resistance than conventional liquid chromatography columns, providing high-throughput performance, resolution and separation in short run times. Monoliths possess also great potential for the clean-up and preparation of complex mixtures. In situ polymerization inside appropriate supports allows the development of several microextraction formats, such as in-tube solid-phase and pipette tip-based extractions. These techniques using porous monoliths offer several advantages, including miniaturization and on-line coupling with analytical instruments. Additionally, monoliths are ideal support media for imprinting template-specific sites, resulting in the so-called molecularly-imprinted monoliths, with ultra-high selectivity. In this review, time-saving LC columns and preparative applications applied to the analysis of residues and contaminants in food in 2010–2014 are described, focusing on recent improvements in design and with emphasis in automated on-line systems and innovative materials and formats.

  3. Comparison of various silica-based monoliths for the analysis of large biomolecules.

    Science.gov (United States)

    Vuignier, Karine; Fekete, Szabolcs; Carrupt, Pierre-Alain; Veuthey, Jean-Luc; Guillarme, Davy

    2013-07-01

    In the present study, three types of silica-based monoliths, i.e. the first and second generations of commercial silica monolithic columns and a wide-pore prototype monolith were compared for the analysis of large biomolecules. These molecules possess molecular weights between 1 and 66 kDa. The gradient kinetic performance of the first-generation monolith was lower than that of the second generation, for large biomolecules (>14 kDa) but very close with smaller ones (1.3-5.8 kDa). In contrast, the wide-pore prototype column was particularly attractive with proteins larger than 19 kDa (higher peak capacity). Among these three columns, the selectivity and retention remained quite similar but a possible larger number of accessible and charged residual silanols was noticed on the wide-pore prototype material, which led to unpredicted small changes in selectivity and slightly broader peaks than expected. The peak shapes attained with the addition of 0.1% formic acid in the mobile phase remained acceptable for MS coupling, particularly for biomolecules of less than 6 kDa. It was found that one of the major issues with all of these silica-based monoliths is the possible poor recovery of large biomolecules (principally with monoclonal antibody fragments of more than 25 kDa).

  4. Fabrication of Porous Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate Monoliths via Thermally Induced Phase Separation

    Directory of Open Access Journals (Sweden)

    Takashi Tsujimoto

    2016-02-01

    Full Text Available This study deals with the fabrication of biodegradable porous materials from bacterial polyester, poly(3-hydroxybutyrate-co-3-hydroxyhexanoate (P3HB3HHx, via thermally induced phase separation. P3HB3HHx monoliths with topological porous structure were prepared by dissolution of P3HB3HHx in dimethyl sulfoxide (DMSO at 85 °C and subsequent quenching. The microstructure of the resulting P3HB3HHx monoliths was changed by the P3HB3HHx concentration of the polymer solution. Differential scanning calorimetry and polarized optical microscope analysis revealed that the P3HB3HHx monoliths crystallized during phase separation and the subsequent aging. The mechanical properties, such as compression modulus and stress, of the monoliths depended on the 3-hydroxyhexanoate content of P3HB3HHx. Furthermore, the P3HB3HHx monolith absorbed linseed oil in preference to water in a plant oil–water mixture. In combination with the biodegradable character of P3HB3HHx, the present study is expected to contribute to the development of bio-based materials.

  5. One-pot preparation of a novel monolith for high performance liquid chromatography applications.

    Science.gov (United States)

    Jiao, Xiaoyan; Shen, Shigang; Shi, Tiesheng

    2015-12-15

    Various novel porous organic-based monoliths with the mode of hydrophobicity were synthesized by in situ free-radical crosslinking copolymerization and optimized for the separations of small molecules and high-performance reversed-phase chromatography (RP-chromatography). These monoliths contained co-polymers based on glycidyl methacrylate (GMA)/ethylene glycol dimethacrylate (EDMA)/tripropylene glycol diacrylate (TPGDA) or EDMA/TPGDA. A mixture of cetanol, methanol and poly (ethylene glycol) (PEG) was used as the porogen, with the ratio of these solvents being varied along with the polymerization temperature to generate a library of monoliths. The conditions were optimized and the resulting poly (GMA-co-TPGDA-co-EDMA) monolith was investigated by infrared spectrometer (IR), field emission scanning electron microscope (FESEM), and mercury intrusion porosimetry (MIP), respectively. The column performance was assessed by the separation of a series of neutral solutes of benzene derivatives. The result demonstrated that the prepared monolith exhibited an RP-chromatographic behavior and relatively homogeneous structure, good permeability and separation performance. Moreover, the relative standard deviations (RSDs) of the retention factor values for benzene derivatives were less than 1.5% (n=7, column-to-column). The approach used in this study was extended to the separation of anilines.

  6. An Inexpensive Field-Widened Monolithic Michelson Interferometer for Precision Radial Velocity Measurements

    Science.gov (United States)

    Mahadevan, Suvrath; Ge, Jian; Fleming, Scott W.; Wan, Xiaoke; DeWitt, Curtis; van Eyken, Julian C.; McDavitt, Dan

    2008-09-01

    We have constructed a thermally compensated field-widened monolithic Michelson interferometer that can be used with a medium-resolution spectrograph to measure precise Doppler radial velocities of stars. Our prototype monolithic fixed-delay interferometer is constructed with off-the-shelf components and assembled using a hydrolysis bonding technique. We installed and tested this interferometer in the Exoplanet Tracker (ET) instrument at the Kitt Peak 2.1 m telescope, an instrument built to demonstrate the principles of dispersed fixed-delay interferometry. An iodine cell allows the interferometer drift to be accurately calibrated, relaxing the stability requirements on the interferometer itself. When using our monolithic interferometer, the ET instrument has no moving parts (except the iodine cell), greatly simplifying its operation. We demonstrate differential radial velocity precision of a few m s-1 on well known radial velocity standards and planet bearing stars when using this interferometer. Such monolithic interferometers will make it possible to build relatively inexpensive instruments that are easy to operate and capable of precision radial velocity measurements. A larger multiobject version of the Exoplanet Tracker will be used to conduct a large scale survey for planetary systems as part of the Sloan Digital Sky Survey III (SDSS III). Variants of the techniques and principles discussed in this paper can be directly applied to build large monolithic interferometers for such applications, enabling the construction of instruments capable of efficiently observing many stars simultaneously at high velocity precision.

  7. Effect of endodontic access cavity preparation on monolithic and ceramic veneered zirconia restorations.

    Science.gov (United States)

    Grobecker-Karl, Tanja; Christian, Mirko; Karl, Matthias

    2016-01-01

    Due to the high chipping rates observed in veneered zirconia ceramic restorations, the use of monolithic zirconia restorations has been recommended. This study tried to compare veneered and monolithic zirconia fixed dental prostheses (FDPs) with respect to the amount of damage induced by endodontic access preparation. Monolithic and ceramic veneered (n = 10) three-unit restorations (retainers: first premolar and first molar; pontic: second premolar) were subject to endodontic access cavity preparation in both retainers using a diamond rotary instrument under continuous water cooling. The number of chipping fractures and microfractures detected using the fluorescent penetrant method were recorded. Statistical analysis was based on Wilcoxon rank sum tests with Bonferroni correction (level of significance α = .05). Only one microfracture could be identified in the group of monolithic FDPs while a maximum of seven microfractures and three chipping fractures per retainer crown were recorded in the group of veneered restorations. At the premolar site, the veneered restorations showed significantly more microfractures (P = .0055) and chipping fractures (P = .0008). At the molar site, no significant difference with respect to microfractures could be detected (P = .0767), while significantly more chipping fractures occurred in the veneered samples (P = .0293). Monolithic zirconia restorations seem to be less susceptible to damage when endodontic access cavities have to be prepared as compared to veneered zirconia reconstructions. However, no conclusions can be drawn on the long-term performance of a specific restoration based on this study.

  8. Methacrylate-bonded covalent-organic framework monolithic columns for high performance liquid chromatography.

    Science.gov (United States)

    Liu, Li-Hua; Yang, Cheng-Xiong; Yan, Xiu-Ping

    2017-01-06

    Covalent-organic frameworks (COFs) are a newfangled class of intriguing microporous materials. Considering their unique properties, COFs should be promising as packing materials for high performance liquid chromatography (HPLC). However, the irregular shape and sub-micrometer size of COFs synthesized via the traditional methods render the main obstacles for the application of COFs in HPLC. Herein, we report the preparation of methacrylate-bonded COF monolithic columns for HPLC to overcome the above obstacles. The prepared COF bonded monolithic columns not only show good homogeneity and permeability, but also give high column efficiency, good resolution and precision for HPLC separation of small molecules including polycyclic aromatic hydrocarbons, phenols, anilines, nonsteroidal anti-inflammatory drugs and benzothiophenes. Compared with the bare polymer monolithic column, the COF bonded monolithic columns show enhanced hydrophobic, π-π and hydrogen bond interactions in reverse phase HPLC. The results reveal the great potential of COF bonded monoliths for HPLC and COFs in separation sciences. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Characterization of polymer monoliths containing embedded nanoparticles by scanning transmission X-ray microscopy (STXM).

    Science.gov (United States)

    Arrua, R Dario; Hitchcock, Adam P; Hon, Wei Boon; West, Marcia; Hilder, Emily F

    2014-03-18

    The structural and chemical homogeneity of monolithic columns is a key parameter for high efficiency stationary phases in liquid chromatography. Improved characterization techniques are needed to better understand the polymer morphology and its optimization. Here the analysis of polymer monoliths by scanning transmission X-ray microscopy (STXM) is presented for the first time. Poly(butyl methacrylate-co-ethyleneglycoldimethacrylate) [poly(BuMA-co-EDMA)] monoliths containing encapsulated divinylbenzene (DVB) nanoparticles were characterized by STXM, which gives a comprehensive, quantitative chemical analysis of the monolith at a spatial resolution of 30 nm. The results are compared with other methods commonly used for the characterization of polymer monoliths [scanning electron microscopy (SEM), transmission electron microscopy (TEM), mercury porosimetry, and nitrogen adsorption]. The technique permitted chemical identification and mapping of the nanoparticles within the polymeric scaffold. Residual surfactant, which was used during the manufacture of the nanoparticles, was also detected. We show that STXM can give more in-depth chemical information for these types of materials and therefore lead to a better understanding of the link between polymer morphology and chromatographic performance.

  10. Microbially mediated mineral carbonation

    Science.gov (United States)

    Power, I. M.; Wilson, S. A.; Dipple, G. M.; Southam, G.

    2010-12-01

    Mineral carbonation involves silicate dissolution and carbonate precipitation, which are both natural processes that microorganisms are able to mediate in near surface environments (Ferris et al., 1994; Eq. 1). (Ca,Mg)SiO3 + 2H2CO3 + H2O → (Ca,Mg)CO3 + H2O + H4SiO4 + O2 (1) Cyanobacteria are photoautotrophs with cell surface characteristics and metabolic processes involving inorganic carbon that can induce carbonate precipitation. This occurs partly by concentrating cations within their net-negative cell envelope and through the alkalinization of their microenvironment (Thompson & Ferris, 1990). Regions with mafic and ultramafic bedrock, such as near Atlin, British Columbia, Canada, represent the best potential sources of feedstocks for mineral carbonation. The hydromagnesite playas near Atlin are a natural biogeochemical model for the carbonation of magnesium silicate minerals (Power et al., 2009). Field-based studies at Atlin and corroborating laboratory experiments demonstrate the ability of a microbial consortium dominated by filamentous cyanobacteria to induce the precipitation of carbonate minerals. Phototrophic microbes, such as cyanobacteria, have been proposed as a means for producing biodiesel and other value added products because of their efficiency as solar collectors and low requirement for valuable, cultivable land in comparison to crops (Dismukes et al., 2008). Carbonate precipitation and biomass production could be facilitated using specifically designed ponds to collect waters rich in dissolved cations (e.g., Mg2+ and Ca2+), which would allow for evapoconcentration and provide an appropriate environment for growth of cyanobacteria. Microbially mediated carbonate precipitation does not require large quantities of energy or chemicals needed for industrial systems that have been proposed for rapid carbon capture and storage via mineral carbonation (e.g., Lackner et al., 1995). Therefore, this biogeochemical approach may represent a readily

  11. Autothermal reforming of biogas over a monolithic catalyst

    Institute of Scientific and Technical Information of China (English)

    Sadao Araki; Naoe Hino; Takuma Mori; Susumu Hikazudani

    2010-01-01

    This study focused on measurement of the autothermal reforming of biogas over a Ni based monolithic catalyst.The effects of the steam/CH4 (S/C) ratio,O2/CH4 (O2/C) ratio and temperature were investigated.The CH4 conversions were higher under all examined temperatures than the equilibrium conversion calculated using the blank outlet temperature,because the catalyst layer was heated by the exothermic catalytic partial oxidation reaction.The CH4 conversion increased with increasing O2/C ratio.Moreover,the CH4 conversion was higher than the equilibrium conversion calculated using the blank outlet temperature for O2/C>0.42 and reached about 100% at O2/C=0.55.However,the hydrogen concentration decreased for O2/C>0.45 because hydrogen was combusted to steam in the presence of excess oxygen.On the other hand,the hydrogen and CO2 concentrations increased and the CO concentration decreased with increasing S/C ratio.As a result,it was found that the highest hydrogen concentrations and CH4 conversions were attained at the O2/C ratios of 0.45-0.55 and the S/C ratios of 1.5-2.5.Moreover,the H2/CO ratio could also be controlled in the range from about 2 to 3.5 to give at least 90% CH4 conversion,by regulating the O2/C or S/C ratios.

  12. Groundwater recharge measurements in gravel sandy sediments with monolith lysimeter

    Science.gov (United States)

    Bracic Zeleznik, Branka; Souvent, Petra; Cencur Curk, Barbara; Zupanc, Vesna

    2013-04-01

    Ljubljana field aquifer is recharging through precipitation and the river Sava, which has the snow-rain flow regime. The sediments of the aquifer have high permeability and create fast flow as well as high regeneration of the dynamic reserves of the Ljubljana field groundwater resource. Groundwater recharge is vulnerable to climate change and it is very important for drinking water supply management. Water stored in the soil and less permeable layers is important for water availability under extreme weather conditions. Measurements of water percolation through the vadose zone provide important input for groundwater recharge assessment and estimation of contaminant migration from land surface to the groundwater. Knowledge of the processes governing groundwater recharge in the vadose zone is critical to understanding the overall hydrological cycle and quantifying the links between land uses and groundwater quantity and quality. To improve the knowledge on water balance for Ljubljana field aquifer we establish a lysimeter for measurements of processes in unsaturated zone in well field Kleče. The type of lysimeter is a scientific lysimeter designed to solve the water balance equation by measuring the mass of the lysimeter monolith as well as that of outflow tank with high accuracy and high temporal resolution. We evaluated short period data, however the chosen month demonstrates weather extremes of the local climate - relatively dry periods, followed by high precipitation amount. In time of high water usage of vegetation only subsequent substantial precipitation events directly results in water flow towards lower layers. At the same time, gravely layers of the deeper parts of the unsaturated zone have little or no capacity for water retention, and in the event that water line leaves top soil, water flow moves downwards fairly quickly. On one hand this confirms high recharge capacity of Ljubljana field aquifer from precipitation on green areas; on the other hand it

  13. Physical properties of monolithic U8 wt.%-Mo

    Science.gov (United States)

    Hengstler, R. M.; Beck, L.; Breitkreutz, H.; Jarousse, C.; Jungwirth, R.; Petry, W.; Schmid, W.; Schneider, J.; Wieschalla, N.

    2010-07-01

    As a possible high density fuel for research reactors, monolithic U8 wt.%-Mo ("U8Mo") was examined with regard to its structural, thermal and electric properties. X-ray diffraction by the Bragg-Brentano method was used to reveal the tetragonal lattice structure of rolled U8Mo. The specific heat capacity of cast U8Mo was determined by differential scanning calorimetry, its thermal diffusivity was measured by the laser flash method and its mass density by Archimedes' principle. From these results, the thermal conductivity of U8Mo in the temperature range from 40 °C to 250 °C was calculated; in the measured temperature range, it is in good accordance with literature data for UMo with 8 and 9 wt.% Mo, is higher than for 10 wt.% Mo and lower than for 5 wt.% Mo. The electric conductivity of rolled and cast U8Mo was measured by a four-wire method and the electron based part of the thermal conductivity calculated by the Wiedemann-Frantz law. Rolled and cast U8Mo was irradiated at about 150 °C with 80 MeV 127I ions to receive the same iodine ion density in the damage peak region as the fission product density in the fuel of a typical high flux reactor after the targeted nuclear burn-up. XRD analysis of irradiated U8Mo showed a change of the lattice parameters as well as the creation of UO 2 in the superficial sample regions; however, a phase change by irradiation was not observed. The determination of the electron based part of the thermal conductivity of the irradiated samples failed due to high measurement errors which are caused by the low thickness of the damage region in the ion irradiated samples.

  14. Fabrication of the LSST monolithic primary-tertiary mirror

    Science.gov (United States)

    Tuell, Michael T.; Martin, Hubert M.; Burge, James H.; Ketelsen, Dean A.; Law, Kevin; Gressler, William J.; Zhao, Chunyu

    2012-09-01

    As previously reported (at the SPIE Astronomical Instrumentation conference of 2010 in San Diego1), the Large Synoptic Survey Telescope (LSST) utilizes a three-mirror design in which the primary (M1) and tertiary (M3) mirrors are two concentric aspheric surfaces on one monolithic substrate. The substrate material is Ohara E6 borosilicate glass, in a honeycomb sandwich configuration, currently in production at The University of Arizona’s Steward Observatory Mirror Lab. We will provide an update to the status of the mirrors and metrology systems, which have advanced from concepts to hardware in the past two years. In addition to the normal requirements for smooth surfaces of the appropriate prescriptions, the alignment of the two surfaces must be accurately measured and controlled in the production lab, reducing the degrees of freedom needed to be controlled in the telescope. The surface specification is described as a structure function, related to seeing in excellent conditions. Both the pointing and centration of the two optical axes are important parameters, in addition to the axial spacing of the two vertices. This paper details the manufacturing process and metrology systems for each surface, including the alignment of the two surfaces. M1 is a hyperboloid and can utilize a standard Offner null corrector, whereas M3 is an oblate ellipsoid, so it has positive spherical aberration. The null corrector is a phase-etched computer-generated hologram (CGH) between the mirror surface and the center-of-curvature. Laser trackers are relied upon to measure the alignment and spacing as well as rough-surface metrology during looseabrasive grinding.

  15. Preparation of boronate-functionalized molecularly imprinted monolithic column with polydopamine coating for glycoprotein recognition and enrichment.

    Science.gov (United States)

    Lin, Zian; Wang, Juan; Tan, Xiaoqing; Sun, Lixiang; Yu, Ruifang; Yang, Huanghao; Chen, Guonan

    2013-12-06

    A novel imprinting strategy using reversible covalent complexation of glycoprotein was described for creating glycoprotein-specific recognition cavities on boronate-functionalized monolithic column. Based on it, a molecularly imprinted monolithic column was prepared by self-polymerization of dopamine (DA) on the surface of 4-vinylphenylboronic acid (VPBA)-based polymeric skeletons after reversible immobilization of horseradish peroxidase (HRP). Due to the combination of boronate affinity and surface imprinting of DA, the stable and accessible recognition sites in the as-prepared imprinted monolith could be obtained after the removal of the template, which facilitated the rebinding of the template and provided good reproducibility and lifetime of use. The recognition behaviors of proteins on the bare VPBA-based, HRP-imprinted and nonimprinted monolithic columns were evaluated in detail and the results showed that the HRP-imprinted monolith exhibited higher recognition ability toward the template than another two monolithic columns. Not only nonglycoproteins but also glycoproteins can be well separated with the HRP-imprinted monolith. In addition, the feasibility of the HRP-imprinted monolith, adopted as an in-tube solid phase microextraction (in-tube SPME), was further assessed by selective extraction and enrichment of HRP from human serum. The good results demonstrated its potential in glycoproteome analysis. Copyright © 2013 Elsevier B.V. All rights reserved.

  16. The Importance of Pressure Sampling Frequency in Models for Determination of Critical Wave Loadings on Monolithic Structures

    DEFF Research Database (Denmark)

    Burcharth, Hans F.; Andersen, Thomas Lykke; Meinert, Palle

    2008-01-01

    Wave induced pressures on model scale monolithic structures like caissons and concrete superstructures on rubble mound breakwaters show very peaky variations, even in cases without impacts from slamming waves.......Wave induced pressures on model scale monolithic structures like caissons and concrete superstructures on rubble mound breakwaters show very peaky variations, even in cases without impacts from slamming waves....

  17. Measurement and Modeling of the Transfer Function of a Monolithic SOA-EA 2R-Regenerator

    DEFF Research Database (Denmark)

    Christiansen, Lotte Jin; Öhman, Filip; Kjær, Rasmus

    2005-01-01

    We have measured steep power transfer characteristics with tunable threshold for a monolithic 2R-regenerator combining amplifying and absorbing sections. Modeling results explain the basic characteristics.......We have measured steep power transfer characteristics with tunable threshold for a monolithic 2R-regenerator combining amplifying and absorbing sections. Modeling results explain the basic characteristics....

  18. Preparation and examination of monolithic in-needle extraction (MINE) device for the direct analysis of liquid samples

    Energy Technology Data Exchange (ETDEWEB)

    Pietrzyńska, Monika, E-mail: monikapietrzynska@gmail.com; Voelkel, Adam; Bielicka-Daszkiewicz, Katarzyna

    2013-05-07

    Graphical abstract: -- Highlights: •MINE device for isolation of analytes from water samples. •Nine polymer poly(styrene-divinylbenzene) monoliths prepared in stainless steel needles. •High efficiency of in-needle extraction systems based on monolithic materials. •New possibilities in sample preparation area. -- Abstract: Combination of extraction and chromatographic techniques opens NEW possibilities in sample preparation area. Macroporous poly(styrene-divinylbenzene) (PS-DVB) monoliths were prepared by in situ polymerization in stainless steel needles. The surface of stainless steel needle was modified earlier by the silane coupling agent. Monolithic materials located inside needles were used as the in-needle extraction device. Scanning electron microscope (SEM) images were obtained for nine monoliths. Spectra of prepared materials were also performed with the use of two techniques: Attenuated Total Reflectance (ATR) and Fourier Transform Infrared Spectroscopy (FTIR). The new monolithic in-needle extraction (MINE) devices were used in the preparation of a series of test water samples for chromatographic analysis. The extraction of phenolic compounds from water samples was carried out by pumping liquid samples through the MINE device. Obtained results indicate a high efficiency of in-needle extraction systems based on monolithic materials. Breakthrough volume and the sorption efficiency of prepared monolithic in-needle extraction devices were determined experimentally. The achieved recovery was close to 90%, and determined LOQ values varied between 0.4 and 6 μg.

  19. Effect of the presence of an ordered micro-pillar array on the formation of silica monoliths

    NARCIS (Netherlands)

    Detobel, Frederik; Eghbali, Hamed; De Bruyne, Selm; Terryn, Herman; Gardeniers, Han; Desmet, Gert

    2009-01-01

    We report on the synthesis of siloxane-based monoliths in the presence of a two-dimensional, perfectly ordered array of micro-pillars. Both methyltrimethoxysilane- and tetramethoxysilane-based monoliths were considered. The obtained structures were analyzed using scanning-electron microscopy and can

  20. Monolithic thermally bonded Er3+, Yb3+:glass/Co2+:MgAl2O4 microchip lasers

    Science.gov (United States)

    Mlynczak, Jaroslaw; Belghachem, Nabil

    2015-12-01

    The highest ever reported 10 kW peak power in monolithic thermally bonded Er3+, Yb3+:glass/Co2+:MgAl2O4 microchip laser was achieved. To show the superiority of monolithic microchip lasers over those with external mirrors the laser generation characteristics of the same samples in both cases were compared.

  1. Design and evaluation of synthetic silica-based monolithic materials in shrinkable tube for efficient protein extraction.

    Science.gov (United States)

    Alzahrani, Eman; Welham, Kevin

    2011-10-21

    Sample pretreatment is a required step in proteomics in order to remove interferences and preconcentrate the samples. Much research in recent years has focused on porous monolithic materials since they are highly permeable to liquid flow and show high mass transport compared with more common packed beds. These features are due to the micro-structure within the monolithic silica column which contains both macropores that reduce the back pressure, and mesopores that give good interaction with analytes. The aim of this work was to fabricate a continuous porous silica monolithic rod inside a heat shrinkable tube and to compare this with the same material whose surface has been modified with a C(18) phase, in order to use them for preconcentration/extraction of proteins. The performance of the silica-based monolithic rod was evaluated using eight proteins; insulin, cytochrome C, lysozyme, myoglobin, β-lactoglobulin, ovalbumin, hemoglobin, and bovine serum albumin at a concentration of 60 μM. The results show that recovery of the proteins was achieved by both columns with variable yields; however, the C(18) modified silica monolith gave higher recoveries (92.7 to 109.7%) than the non-modified silica monolith (25.5 to 97.9%). Both silica monoliths can be used with very low back pressure indicating a promising approach for future fabrication of the silica monolith inside a microfluidic device for the extraction of proteins from biological media.

  2. Proton Conduction in Sulfonated Organic-Inorganic Hybrid Monoliths with Hierarchical Pore Structure.

    Science.gov (United States)

    von der Lehr, Martin; Seidler, Christopher F; Taffa, Dereje H; Wark, Michael; Smarsly, Bernd M; Marschall, Roland

    2016-09-28

    Porous organic-inorganic hybrid monoliths with hierarchical porosity exhibiting macro- and mesopores are prepared via sol-gel process under variation of the mesopore size. Organic moieties in the pore walls are incorporated by substituting up to 10% of the silicon precursor tetramethylorthosilicate with bisilylated benzene molecules. After functionalization with sulfonic acid groups, the resulting sulfonated hybrid monoliths featuring a bimodal pore structure are investigated regarding proton conduction depending on temperature and relative humidity. The hierarchical pore system and controlled mesopore design turn out to be crucial for sulfonation and proton conduction. These sulfonated hybrid hierarchical monoliths containing only 10% organic precursor exhibit higher proton conduction at different relative humidities than sulfonated periodic mesoporous organosilica made of 100% bisilylated precursors exhibiting solely mesopores, even with a lower concentration of sulfonic acid groups.

  3. Fabrication and Characterisation of Low-noise Monolithic Mode-locked Lasers

    DEFF Research Database (Denmark)

    Larsson, David

    2007-01-01

    This thesis deals with the fabrication and characterisation of monolithic semiconductor mode-locked lasers for use in optical communication systems. Other foreseeable applications may be as sources in microwave photonics and optical sampling. The thesis also deals with the design and fabrication...... of intracavity monolithically integrated filters. The common dnominator among the diffrent parts of the thesis is how to achieve and measure the lowest possible noise. Achieving low noise has been pinpointed as one of the most important and difficult challenges for semiconductor mode-locked lasers. The main...... result of this thesis are a fabrication process of a monolithic and deeply etched distributed Bragg reflector and a characterisation system for measurement of quantum limitid timing noise at high repetition rates. The Bragg reflector is a key component in achieving transform limited pulses with low noise...

  4. Monolithic formulation of electromechanical systems within the context of hybrid finite elements

    Science.gov (United States)

    Agrawal, Manish; Jog, C. S.

    2017-03-01

    In electromechanical devices, a strong coupling exists between the electromagnetic and displacement field. Due to this strong interaction, a need arises to develop a robust, fully coupled scheme for modeling electromechanical phenomena. With this goal in view, we present a monolithic numerical scheme for modeling fully coupled electromechanical systems. It is shown in the literature that for structural problems, hybrid elements that are based on a two-field variational formulation are less susceptible to locking and provide a robust numerical strategy especially for shell-type structures. Hence, we extend our monolithic formulation to the hybrid finite element framework. Our monolithic formulation is based on a total Lagrangian framework, where the eddy current and structural equations are solved on the reference configuration. Consistent linearization is performed to ensure a quadratic rate of convergence. The efficacy of the presented algorithm, and especially that of the hybrid formulation is demonstrated with the help of numerical examples.

  5. An innovative monolithic column preparation for the isolation of 25 kilo base pairs DNA.

    Science.gov (United States)

    Ongkudon, Clarence M; Pan, Sharadwata; Danquah, Michael K

    2013-11-29

    The use of large DNAs in preparing multivalent vaccines that will eventually give protective immunity against multiple pathogenic microbes is becoming a major debate nowadays. One of the important issues in ensuring the successful implementation of the new vaccine technology is the development of a chromatographic technique that can handle larger DNAs. This paper reports the development of a novel conical monolithic column format with pore and surface characteristics engineered for the isolation of 25 kbp DNA in a single step fashion. An effective method of eliminating wall channelling, a defect of most conventional monolithic chromatography systems which has caused significant loss of product, was applied to maximise DNA recovery. This method was based on a systematic reduction of wall channel size based on a predetermined correlation between column’s back pressure and wall channel size of a particular monolith pore size.

  6. Monolithic ionizing particle detector based on active matrix of functionally integrated structures

    Energy Technology Data Exchange (ETDEWEB)

    Murashev, V.N. [National University of Science and Technology “MISIS” (Russian Federation); Legotin, S.A., E-mail: serlego@mail.ru [National University of Science and Technology “MISIS” (Russian Federation); Karmanov, D.E. [Lomonosov Moscow State University, Skobeltsyn Institute of Nuclear Physics (MSU SINP) (Russian Federation); Baryshnikov, F.M.; Didenko, S.I. [National University of Science and Technology “MISIS” (Russian Federation)

    2014-02-15

    Highlights: • A new type of monolithic silicon position detector is presented. • An operating principle, design and technology of the detector are described. • Calculated estimations of the detecting efficiency are carried out. • Experimental results of alpha-particle and electron detection are shown. -- Abstract: An operating principle, design and technology of a new type of the monolithic silicon position detector (MSPD) for registration of ionizing particles and photons are described. The detector represents a specialized monolithic silicon VLSI that contains a two-dimensional detecting matrix of active functionally integrated bipolar structures and peripheral electronic circuitry for signal amplification and processing. This paper presents experimental results of α-particles and electrons detection with position accuracy and operation speed better than 12.5 μm and 1 ns, respectively. The given estimations show the capabilities of this detector and its advantages in comparison with analogs.

  7. Experimental characterization of the transport phenomena, adsorption, and elution in a protein A affinity monolithic medium.

    Science.gov (United States)

    Herigstad, M Omon; Dimartino, Simone; Boi, Cristiana; Sarti, Giulio C

    2015-08-14

    A commercially available convective interaction media (CIM) Protein A monolithic column was fully characterized in view of its application for the affinity capture of IgG in monoclonal antibody production processes. By means of moment analysis, the interstitial porosity and axial dispersion coefficient were determined. The frontal analysis method of characteristic points was employed, for the first time with monolithic media, to determine the dynamic binding capacity. The effects of the flow rate and pH on the total recovery of polyclonal IgG and elution profile were evaluated. A comparison with literature data for Protein A chromatography beads demonstrate the superior bed utilization of monolithic media, which gave better performance at lower residence times.

  8. High-density 3D graphene-based monolith and related materials, methods, and devices

    Energy Technology Data Exchange (ETDEWEB)

    Worsley, Marcus A.; Baumann, Theodore F.; Biener, Juergen; Charnvanichborikarn, Supakit; Kucheyev, Sergei; Montalvo, Elizabeth; Shin, Swanee; Tylski, Elijah

    2017-03-21

    A composition comprising at least one high-density graphene-based monolith, said monolith comprising a three-dimensional structure of graphene sheets crosslinked by covalent carbon bonds and having a density of at least 0.1 g/cm.sup.3. Also provided is a method comprising: preparing a reaction mixture comprising a suspension and at least one catalyst, said suspension selected from a graphene oxide (GO) suspension and a carbon nanotube suspension; curing the reaction mixture to produce a wet gel; drying the wet gel to produce a dry gel, said drying step is substantially free of supercritical drying and freeze drying; and pyrolyzing the dry gel to produce a high-density graphene-based monolith. Exceptional combinations of properties are achieved including high conductive and mechanical properties.

  9. An Inexpensive Field-Widened Monolithic Michelson Interferometer for Precision Radial Velocity Measurements

    CERN Document Server

    Mahadevan, Suvrath; Fleming, Scott W; Wan, Xiaoke; DeWitt, Curtis; van Eyken, Julian C; McDavitt, Dan

    2008-01-01

    We have constructed a thermally compensated field-widened monolithic Michelson interferometer that can be used with a medium-resolution spectrograph to measure precise Doppler radial velocities of stars. Our prototype monolithic fixed-delay interferometer is constructed with off-the-shelf components and assembled using a hydrolysis bonding technique. We installed and tested this interferometer in the Exoplanet Tracker (ET) instrument at the Kitt Peak 2.1m telescope, an instrument built to demonstrate the principles of dispersed fixed delay interferometry. An iodine cell allows the interferometer drift to be accurately calibrated, relaxing the stability requirements on the interferometer itself. When using our monolithic interferometer, the ET instrument has no moving parts (except the iodine cell), greatly simplifying its operation. We demonstrate differential radial velocity precision of a few m s$^{-1}$ on well known radial velocity standards and planet bearing stars when using this interferometer. Such mon...

  10. Preparation of carbon monoliths having tailored pore structure from porous polymer precursors

    Energy Technology Data Exchange (ETDEWEB)

    Lagasse, R.R.

    1993-04-01

    This work concerns preparing tailored porous carbon monoliths by pyrolyzing porous polymer precursors. Prior work in this laboratory (1) demonstrated that a low density (0.05 g/cm{sup 3}), high void fraction (97 vol%) carbon monolith could be prepared by pyrolyzing a porous poly(acrylonitrile) (PAN) precursor. A higher density, more robust carbon material is preferred for certain applications, such as electrodes for electrochemical devices. The present work demonstrates that porous carbon monoliths having mass density of 0.7 g/cm{sup 3} can be prepared from a porous PAN precursor if the pyrolysis is controlled carefully. The macropore structure of the carbon is adjusted by changing the pore structure of the PAN precursor, and the finer scale structure (such as the crystallite size L{sub c}) is adjusted by varying the pyrolysis or heat treatment temperature.

  11. Preparation of carbon monoliths having tailored pore structure from porous polymer precursors

    Energy Technology Data Exchange (ETDEWEB)

    Lagasse, R.R.

    1993-01-01

    This work concerns preparing tailored porous carbon monoliths by pyrolyzing porous polymer precursors. Prior work in this laboratory (1) demonstrated that a low density (0.05 g/cm[sup 3]), high void fraction (97 vol%) carbon monolith could be prepared by pyrolyzing a porous poly(acrylonitrile) (PAN) precursor. A higher density, more robust carbon material is preferred for certain applications, such as electrodes for electrochemical devices. The present work demonstrates that porous carbon monoliths having mass density of 0.7 g/cm[sup 3] can be prepared from a porous PAN precursor if the pyrolysis is controlled carefully. The macropore structure of the carbon is adjusted by changing the pore structure of the PAN precursor, and the finer scale structure (such as the crystallite size L[sub c]) is adjusted by varying the pyrolysis or heat treatment temperature.

  12. Macroporous glass monoliths prepared from powdered niobium phosphate glass by fast sintering

    Energy Technology Data Exchange (ETDEWEB)

    Lacerda Mauricio, Vitor; Alves, Oswaldo Luiz; Odone Mazali, Italo, E-mail: mazali@iqm.unicamp.br

    2011-03-15

    Macroporous monoliths were prepared by very fast sintering (between 3 and 15 min) of niobophosphate glass powders at low temperature (1018 K) using cellulose as a foaming agent. The porous materials were analyzed by thermal analysis, Raman spectroscopy, scanning electron microscopy and powder X-ray diffraction, and further investigated using X-ray microtomography, a non-destructive technique capable of reconstructing three-dimensional models of samples and providing structural measurements. The progression of the porosity of the monoliths depends on the sintering time (3 to 15 min) and the amount (up to 50% in mass) of cellulose used. The macroporous glass monoliths may find application in integrated chemical systems and in filtering processes.

  13. Continuous-Flow Monolithic Silica Microreactors with Arenesulphonic Acid Groups: Structure–Catalytic Activity Relationships

    Directory of Open Access Journals (Sweden)

    Agnieszka Ciemięga

    2017-08-01

    Full Text Available The performance of monolithic silica microreactors activated with sulphonic acid groups and a packed bed reactor with Amberlyst 15 resin were compared in the esterification of acetic acid with n-butanol. The monolithic microreactors were made of single silica rods with complex pore architecture, differing in the size of mesopores, and in particular, flow-through macropores which significantly affected the flow characteristic of the continuous system. The highest ester productivity of 105.2 mol·molH+−1·h−1 was achieved in microreactor M1 with the largest porosity, characterized by a total pore volume of 4 cm3·g−1, mesopores with 20 nm diameter, and large flow-through macropores 30–50 μm in size. The strong impact of the permeability of the monoliths on a reaction kinetics was shown.

  14. Thiol-yne Click Adamantane Monolithic Stationary Phase for Capillary Electrochromatography

    Institute of Scientific and Technical Information of China (English)

    Dao, Thi Thu Hien; Guerrouache, Mohamed; Carbonnier, Benjamin

    2012-01-01

    A porous crosslinked organic polymer based on N-acryloxysuccinimide (NAS) and ethylene dimethacrylate (EDMA) was prepared inside 75 μm i.d. fused silica capillary as functionalizable monolithic stationary phase for electrochromatographic applications. Succinimide groups on the monolith surface provide reactive sites able to re- act readily through standard electrophile-nucleophile chemistry. Propargylamine was used to prepare alkyne func- tionalized poly(NAS-co-EDMA). Onto this thiol-reactive polymer surface was grafted adamantane units via a photochemically-driven addition reaction. Chemical characterization was performed in situ after each synthetic step by means of Raman spectroscopy and grafting kinetics was investigated to ensure quantitative grafting of 1-adamantanethiol. The as-designed monolithic stationary phase exhibited typical reversed-phase separation mechanism as evidenced by the linear increase of the logarithm of retention factor of neutral aromatic solutes with the increase of the aqueous buffer content in the mobile phase.

  15. Assessment of the Grouted IXC Monolith in Support of K East Basin Hazard Categorization

    Energy Technology Data Exchange (ETDEWEB)

    Short, Steven M.; Dodson, Michael G.; Alzheimer, James M.; Meyer, Perry A.

    2007-10-12

    Addendum to original report updating the structural analysis of the I-beam accident to reflect a smaller I-beam than originally assumed (addendum is 2 pages). The K East Basin currently contains six ion exchange columns (IXCs) that were removed from service over 10 years ago. Fluor Hanford plans to immobilize the six ion exchange columns (IXCs) in place in a concrete monolith. PNNL performed a structural assessment of the concrete monolith to determine its capability to absorb the forces imposed by postulated accidents and protect the IXCs from damage and thus prevent a release of radioactive material. From this assessment, design specifications for the concrete monolith were identified that would prevent a release of radioactive material for any of the postulated hazardous conditions.

  16. Purification of Astaxanthin from Laminariajaponica by Ionic Liquid-based Monolithic Cartridge

    Institute of Scientific and Technical Information of China (English)

    YOON Chang-hwan; ZHU Tao; ROW Kyung-ho

    2012-01-01

    An effective and accurate method was developed for the extraction of astaxanthin from Laminariajaponica with subsequent separation by ionic liquid-based monolithic cartridge.The optimized extraction conditions including extraction solvent(ethanol),extraction time(90 min) and ultrasonic power(75 W) were obtained by systematical investigation.Chromatographic analysis was performed on a C18 column with ultraviolet(UV) detection at 476nm,and a solution consisting of methanol/acetonitrile/H20/dichloromethane(83:6:6:5,volume ratio) was used as the mobile phase at a flow rate of 0.7 mL/min.After ionic liquid-based monolithic solid phase extraction,17.82 μg/g astaxanthin was obtained from Laminariajaponica.This ionic liquid-based monolithic cartridge exhibits high affinity and selectivity for astaxanthin,and it can be potentially used as the stationary phase of high performance liquid chromatography( HPLC).

  17. In situ sol-gel preparation of porous alumina monoliths for chromatographic separations of adenosine phosphates.

    Science.gov (United States)

    Zajickova, Zuzana; Rubi, Emir; Svec, Frantisek

    2011-06-03

    A method enabling the in situ preparation of porous alumina monoliths within 100 μm i.d. fused silica capillaries has been developed. These monoliths were prepared using the sol-gel process from a mixture consisting of an inorganic aluminum salt, a porogen, an epoxide, and a solvent. We investigated the effects of varying the preparation conditions on the physical characteristics of the monoliths with respect to their potential application in chromatographic separations. The best columns were obtained from a mixture of aluminum chloride hexahydrate, N,N-dimethylformamide, water, ethanol and propylene oxide. Adenosine phosphates were then separated in the optimized column with retention increasing according to number of phosphate functionalities.

  18. A monolithic integrated micro direct methanol fuel cell based on sulfo functionalized porous silicon

    Science.gov (United States)

    Wang, M.; Lu, Y. X.; Liu, L. T.; Wang, X. H.

    2016-11-01

    In this paper, we demonstrate a monolithic integrated micro direct methanol fuel cell (μDMFC) for the first time. The monolithic integrated μDMFC combines proton exchange membrane (PEM) and Pt nanocatalysts, in which PEM is achieved by the functionalized porous silicon membrane and 3D Pt nanoflowers being synthesized in situ on it as catalysts. Sulfo groups functionalized porous silicon membrane serves as a PEM and a catalyst support simultaneously. The μDMFC prototype achieves an open circuit voltage of 0.3 V, a maximum power density of 5.5 mW/cm2. The monolithic integrated μDMFC offers several desirable features such as compatibility with micro fabrication techniques, an undeformable solid PEM and the convenience of assembly.

  19. High-density 3D graphene-based monolith and related materials, methods, and devices

    Science.gov (United States)

    Worsley, Marcus A.; Baumann, Theodore F.; Biener, Juergen; Charnvanichborikarn, Supakit; Kucheyev, Sergei; Montalvo, Elizabeth; Shin, Swanee; Tylski, Elijah

    2017-03-21

    A composition comprising at least one high-density graphene-based monolith, said monolith comprising a three-dimensional structure of graphene sheets crosslinked by covalent carbon bonds and having a density of at least 0.1 g/cm.sup.3. Also provided is a method comprising: preparing a reaction mixture comprising a suspension and at least one catalyst, said suspension selected from a graphene oxide (GO) suspension and a carbon nanotube suspension; curing the reaction mixture to produce a wet gel; drying the wet gel to produce a dry gel, said drying step is substantially free of supercritical drying and freeze drying; and pyrolyzing the dry gel to produce a high-density graphene-based monolith. Exceptional combinations of properties are achieved including high conductive and mechanical properties.

  20. Miniaturized monolithic columns for the electrochromatographic separation and SERS detection of molecules of exobiological interest

    Science.gov (United States)

    Carbonnier, Benjamin; Guerrouache, Mohamed

    Development of miniaturized separation and detection media represents one of the major challenges in the field of modern analytical chemistry dedicated to space exploration. To date, gas chromatography-mass spectrometry has been selected as the method of choice for exobiology flight experiments for seeking for organic molecules and especially potential chemical indicators of life. [1] Liquid phase separation methods have also been developed with for instance, the so-called Mars Organic Analyzer (MOA) capillary electrophoresis (CE) microchip.[2] Although CE offers the advantages of easy miniaturization and high separation efficiency it suffers from a lack of selectivity towards a broad range of analytes with varied chemical nature. In this respect, we propose the use of capillary columns filled with monolithic stationary phases for the electrochromatographic separation of organic molecules of exobiology interest. Polymer monoliths have attracted a great deal of interest in analytical science over the last years as (electro)chromatographic stationary phases [3], immunosensors [4]. Beyond the intrinsic properties of monolithic polymers, i.e. fast mass transport between the monolithic support and the surrounding fluid and high permeability, other major advantages are their easy in situ preparation and tuning of surface functionality. Indeed, monoliths can be simply prepared through free radical copolymerization of a homogeneous mixture made of monomers, cross-linkers, porogenic solvents and initiator. UV-initiation process has been exploited to the synthesis of a discrete section of monolith as a flow-through active element within the confines of micro channels [5,6] while two-step strategies have been reported for the design of varied adsorbent starting with a generic monolith [7,8]. Although a nearly limitless range of monolithic supports can be prepared by this traditional method, the resulting monoliths exhibit unique function. In this contribution, we describe an

  1. Synthesis and Textural Characterization of Mesoporous and Meso-/Macroporous Silica Monoliths Obtained by Spinodal Decomposition

    Directory of Open Access Journals (Sweden)

    Anne Galarneau

    2016-04-01

    Full Text Available Silica monoliths featuring either mesopores or flow-through macropores and mesopores in their skeleton are prepared by combining spinodal phase separation and sol-gel condensation. The macroporous network is first generated by phase separation in acidic medium in the presence of polyethyleneoxides while mesoporosity is engineered in a second step in alkaline medium, possibly in the presence of alkylammonium cations as surfactants. The mesoporous monoliths, also referred as aerogels, are obtained in the presence of alkylpolyethylene oxides in acidic medium without the use of supercritical drying. The impact of the experimental conditions on pore architecture of the monoliths regarding the shape, the ordering, the size and the connectivity of the mesopores is comprehensively discussed based on a critical appraisal of the different models used for textural analysis.

  2. Mineralization of fossil wood

    NARCIS (Netherlands)

    Buurman, P.

    1972-01-01

    Several pieces of fossil wood have been analyzed with X-ray diffraction and were grouped on the basis of mineralogical composition. Various mineralizations were studied in thin sections and by means of the scanning electron microscope. Wood-opals appear to show a structure preservation that points t

  3. Clay Mineral: Radiological Characterization

    Science.gov (United States)

    Cotomácio, J. G.; Silva, P. S. C.; Mazzilli, B. P.

    2008-08-01

    Since the early days, clays have been used for therapeutic purposes. Nowadays, most minerals applied as anti-inflammatory, pharmaceutics and cosmetic are the clay minerals that are used as the active ingredient or, as the excipient, in formulations. Although their large use, few information is available in literature on the content of the radionuclide concentrations of uranium and thorium natural series and 40K in these clay minerals. The objective of this work is to determine the concentrations of 238U, 232Th, 226Ra, 228Ra, 210Pb and 40K in commercial samples of clay minerals used for pharmaceutical or cosmetic purposes. Two kinds of clays samples were obtained in pharmacies, named green clay and white clay. Measurement for the determination of 238U and 232Th activity concentration was made by alpha spectrometry and gamma spectrometry was used for 226Ra, 228Ra, 210Pb and 40K determination. Some physical-chemical parameters were also determined as organic carbon and pH. The average activity concentration obtained was 906±340 Bq kg-1 for 40K, 40±9 Bq kg-1 for 226Ra, 75±9 Bq kg-1 for 228Ra, 197±38 Bq kg-1 for 210Pb, 51±26 Bq kg-1 for 238U and 55±24 Bq kg-1 for 232Th, considering both kinds of clay.

  4. Mixtures and mineral reactions

    Energy Technology Data Exchange (ETDEWEB)

    Saxena, S.; Ganguly, J.

    1987-01-01

    Considerable progress has been made in our understanding of the physicochemical evolution of natural rocks through systematic analysis of the compositional properties and phase relations of their mineral assemblages. This book brings together concepts of classical thermodynamics, solution models, and atomic ordering and interactions that constitute a basis of such analysis, with examples of application to subsolidus petrological problems.

  5. Bioleaching of Minerals

    Energy Technology Data Exchange (ETDEWEB)

    F. Roberto

    2002-02-01

    Bioleaching is the term used to describe the microbial dissolution of metals from minerals. The commercial bioleaching of metals, particularly those hosted in sulfide minerals, is supported by the technical disciplines of biohydrometallurgy, hydrometallurgy, pyrometallurgy, chemistry, electrochemistry, and chemical engineering. The study of the natural weathering of these same minerals, above and below ground, is also linked to the fields of geomicrobiology and biogeochemistry. Studies of abandoned and disused mines indicate that the alterations of the natural environment due to man's activities leave as remnants microbiological activity that continues the biologically mediated release of metals from the host rock (acid rock drainage; ARD). A significant fraction of the world's copper, gold and uranium is now recovered by exploiting native or introduced microbial communities. While some members of these unique communities have been extensively studied for the past 50 years, our knowledge of the composition of these communities, and the function of the individual species present remains relatively limited. Nevertheless, bioleaching represents a major strategy in mineral resource recovery whose importance will increase as ore reserves decline in quality, become more difficult to process (due to increased depth, increased need for comminution, for example), and as environmental considerations eliminate traditional physical processes such as smelting, which have served the mining industry for hundreds of years.

  6. Intensification of Deep Hydrodesulfurization Through a Two-stage Combination of Monolith and Trickle Bed Reactors

    Institute of Scientific and Technical Information of China (English)

    Min Xu; Hui Liu⁎; Shengfu Ji; Chengyue Li

    2014-01-01

    Deep hydrodesulfurization (HDS) is an important process to produce high quality liquid fuels with ultra-low sul-fur. Process intensification for deep HDS could be implemented by developing new active catalysts and/or new types of reactors. In this work, the kinetics of dibenzothiophene (DBT) hydrodesulfurization over Ni-P/SBA-15/cordierite catalyst was investigated at 340-380 °C and 3.0-5.0 MPa. The first-order reaction model with respect to both DBT and H2 was used to fit the kinetics data in a batch recycle operation system. It is found that both the activation energy and rate constant over the Ni-P monolithic catalyst under our operating conditions are close to those over conventionally used HDS catalysts. Comparative performance studies of two types of reactors, i.e., trickle bed reactor and monolithic reactor, were performed based on reactor modeling and simulation. The results indicate that the productivity of the monolithic reactor is 3 times higher than that of the trickle bed reactor on a catalyst weight basis since effective utilization of the catalyst is higher in the monolithic reactor, but the volumetric productivity of the monolithic reactor is lower for HDS of DBT. Based on simulation results, a two-reactor-in-series configuration for hydrodesulfurization is proposed, in which a monolithic reactor is followed by a tickled bed reactor so as to attain intensified performance of the system converting fuel oil of different sulfur-containing compounds. It is il ustrated that the two reactor scheme outperforms the trickle bed reactor both on reactor volume and catalyst mass bases while the content of sulfur is reduced from 200μg·g-1 to about 10μg·g-1.

  7. Fracture Strength of Aged Monolithic and Bilayer Zirconia-Based Crowns

    Directory of Open Access Journals (Sweden)

    Deborah Pacheco Lameira

    2015-01-01

    Full Text Available The purpose of this study was to evaluate the effect of design and surface finishing on fracture strength of yttria-tetragonal zirconia polycrystal (Y-TZP crowns in monolithic (1.5 mm thickness and bilayer (0.8 mm zirconia coping and 0.7 mm porcelain veneer configuration after artificial aging. Bovine incisors received crown preparation and Y-TZP crowns were manufactured using CAD/CAM technique, according to the following groups (n=10: Polished monolithic zirconia crowns (PM; Glazed monolithic zirconia crowns (GM; Bi-layer crowns (BL. Crowns were cemented with resin cement, submitted to artificial aging in a chewing simulator (2.5 million cycles/80 N/artificial saliva/37°C, and tested for fracture strength. Two remaining crowns referring to PM and GM groups were submitted to a chemical composition analysis to measure the level of yttrium after aging. One-way ANOVA and Tukey’s test (P=.05 indicated that monolithic zirconia crowns presented similar fracture strength (PM=3476.2 N ± 791.7; GM=3561.5 N ± 991.6, which was higher than bilayer crowns (2060.4 N ± 810.6. There was no difference in the yttrium content among the three surfaces evaluated in the monolithic crowns. Thus, monolithic zirconia crowns present higher fracture strength than bilayer veneered zirconia after artificial aging and surface finishing does not affect their fracture strength.

  8. Recent Research and Development of Monolithic Column in Ion Chromatography%整体柱离子色谱的研究进展

    Institute of Scientific and Technical Information of China (English)

    陈倩; 于泓

    2011-01-01

    Monolithic columns have been employed in low pressure, fast and high efficient separation, for their many excellent characteristics. When applied to ion chromatography field, monolithic columns can achieve more effective analysis than traditional columns. Therefore, the method of ion chromatography based on monolithic columns attracts increasing interests. In this paper, the sorts of ion chromatography, classification of monolithic stationary phases, preparation ways of monolithic columns, performances and features of monolithic columns were introduced. The application of conventional monolithic columns in ion chromatography and the utilization of capillary monolithic columns in capillary ion chromatography were summarized according to the different assortments and properties of monolithic columns and ion chromatography, which included silica-based monolithic stationary phase and organic polymer-based monolithic stationary phase. The development of ion chromatography based on monolithic columns in the future was reviewed and prospected.%该文介绍了离子色谱的分类,整体柱的分类、制备及特点,并以此为依据归纳总结了常规整体柱在离子色谱中的应用和毛细管整体柱在毛细管离子色谱中的应用,其中包括硅胶基质整体柱和聚合物基质整体柱,评述并展望了整体柱离子色谱的发展前景.

  9. Hierarchically structured monolithic silicalite-1 consisting of crystallized nanoparticles and its performance in the Beckmann rearrangement of cyclohexanone oxime.

    Science.gov (United States)

    Li, Wen-Cui; Lu, An-Hui; Palkovits, Regina; Schmidt, Wolfgang; Spliethoff, Bernd; Schüth, Ferdi

    2005-09-14

    In this study, we present a synthetic pathway for the fabrication of self-supporting zeolite monoliths consisting of crystallized nanoparticles. A resorcinol-formaldehyde-based organic aerogel is used as a template, and silicalite-1 is used as the zeolite example. The silicalite-1 monoliths obtained consist of individual well-defined zeolite nanocrystals with sizes of 30-40 nm. The monoliths exhibit a high mechanical stability and have hierarchical porosity, with micropores within the zeolite particles, a mesopore system formed by the packing of the nanoparticles, and a macropore system on the monolith level. Such monolithic zeolites show high selectivity typically above 80% to epsilon-caprolactam combined with a high rate of reaction of 0.46 g(caprolactame)/(g(catalyst).h) in the Beckmann rearrangement of cyclohexanone oxime.

  10. Highly bioactive polysiloxane modified bioactive glass-poly(ethylene glycol) hybrids monoliths with controlled surface structure for bone tissue regeneration

    Science.gov (United States)

    Chen, Jing; Que, Wenxiu; Xing, Yonglei; Lei, Bo

    2015-03-01

    Crack-free monoliths with controllable surface microstructure have high bioactivities and therefore potential applications in bone tissue regeneration. In this paper, crack-free polydimethylsiloxane-modified bioactive glass-poly (ethylene glycol) (PDMS-BG-PEG) hybrids monoliths were fabricated via using a modified sol-gel process. Results show that the addition of PEG plays an important part in the formation of crack-free and gelation of the monoliths, and surface microstructures of the as-prepared hybrid monoliths were significantly influenced by the concentration and molecular weight of PEG. The samples obtained from PEG 300 had porous surface result in higher bioactivity (apatite formation) in simulated body fluid (SBF), while the samples obtained from PEG 600 had the smooth surface and inhibited the formation of apatite layer in SBF. These as-prepared hybrid monoliths can be used as a good candidate of implant and scaffold for highly efficient bone tissue regeneration.

  11. Application of Convective Interaction Media (CIM) disk monolithic columns for fast separation and monitoring of organic acids.

    Science.gov (United States)

    Vodopivec, M; Podgornik, A; Berovic, M; Strancar, A

    2000-11-01

    The separation of organic acids on the anion-exchange monolithic support, commercially available as Convective Interaction Media (CIM), is presented in this study. It is demonstrated that citric, isocitric, pyruvic, fumaric, malic, and alpha-ketoglutaric acid can be successfully separated using a CIM monolithic column of suitable user-adjustable length. The effect of the mobile phase composition on the separation is investigated. CIM monolithic columns of adjustable length from 3 to 18 mm are compared regarding the resolution and the back pressure. It is shown that the CIM monolithic column of 12 mm in length enables a good separation of all six organic acids within 3 min and exhibits a linear dependence of back pressure versus flow rate. The resolution and the dynamic binding capacity are found to be flow-unaffected. A filtrated sample of bioprocess supernatant is analyzed without previous pretreatment, which indicates the possibility of online monitoring of small molecules during the bioprocess using CIM monolithic columns.

  12. Preparation of a monolith functionalized with zinc oxide nanoparticles and its application in the enrichment of fluoroquinolone antibiotics.

    Science.gov (United States)

    Liu, Dan; Ma, Jiutong; Jin, Yan; Li, Xiqian; Zhou, Xiao; Jia, Qiong; Zhou, Weihong

    2015-01-01

    This study describes the enrichment ability of ZnO-modified methacrylic acid-co-ethylene dimethacrylate polymer monoliths as stationary phases for the simultaneous determination of antibiotics (ofloxacin, ciprofloxacin, enoxacin, and pefloxacin) combined with high-performance liquid chromatography. The prepared monolith was characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, Fourier-transformed infrared spectroscopy, and thermogravimetric analysis. The polymer monolith microextraction method has been applied to the enrichment of fluoroquinolone antibiotics and satisfactory results were obtained in the analysis of water samples. Compared with the conventional methacrylic acid based monolith, the developed monolith exhibited a higher enrichment capacity because of the introduction of zinc oxide into the preparation process. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Aggregate and Mineral Resources - Industrial Mineral Mining Operations

    Data.gov (United States)

    NSGIC Education | GIS Inventory — An Industrial Mineral Mining Operation is a DEP primary facility type related to the Industrial Mineral Mining Program. The sub-facility types are listed below:Deep...

  14. Aggregate and Mineral Resources - Industrial Mineral Mining Operations

    Data.gov (United States)

    NSGIC GIS Inventory (aka Ramona) — An Industrial Mineral Mining Operation is a DEP primary facility type related to the Industrial Mineral Mining Program. The sub-facility types are listed below:Deep...

  15. Advanced digital modulation: Communication techniques and monolithic GaAs technology

    Science.gov (United States)

    Wilson, S. G.; Oliver, J. D., Jr.; Kot, R. C.; Richards, C. R.

    1983-01-01

    Communications theory and practice are merged with state-of-the-art technology in IC fabrication, especially monolithic GaAs technology, to examine the general feasibility of a number of advanced technology digital transmission systems. Satellite-channel models with (1) superior throughput, perhaps 2 Gbps; (2) attractive weight and cost; and (3) high RF power and spectrum efficiency are discussed. Transmission techniques possessing reasonably simple architectures capable of monolithic fabrication at high speeds were surveyed. This included a review of amplitude/phase shift keying (APSK) techniques and the continuous-phase-modulation (CPM) methods, of which MSK represents the simplest case.

  16. Effect of polishing and glazing on the color and spectral distribution of monolithic zirconia

    OpenAIRE

    Kim, Hee-Kyung; Kim, Sung-Hun; Lee, Jai-Bong; Han, Jung-Suk; Yeo, In-Sung

    2013-01-01

    PURPOSE The aim of this study was to evaluate the effect of polishing and glazing on the color and spectral distribution of monolithic zirconia. MATERIALS AND METHODS Forty-five monolithic zirconia specimens (16.3 mm × 16.4 mm × 2.0 mm) were fabricated and divided into 5 groups according to the number of A2-coloring liquid applications (Group I to V). Each group was divided into 3 subgroups according to the method of surface treatments (n=3): N: no treatment; P: polishing; G: glazing. Color a...

  17. Preparation and applications of monolithic structures containing metal-organic frameworks.

    Science.gov (United States)

    Lv, Yongqin; Tan, Xinyi; Svec, Frantisek

    2017-01-01

    Metal-organic frameworks are a new category of advanced porous materials with large surface areas and porosities, uniform pore sizes, tunable surface chemistry, and structural diversity. In combination with monoliths, they allow the fine tuning of desired interactions required in a variety of applications. This review article summarizes results of recent studies focused on synthetic strategies enabling incorporation of metal-organic frameworks in monolithic structures. A diverse array of applications including chromatographic separation, solid-phase microextraction, sample enrichment, heterogeneous catalysis, and enzymatic catalysis are also described. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Review of data on irradiation creep of monolithic SiC

    Energy Technology Data Exchange (ETDEWEB)

    Garner, F.A.; Youngblood, G.E.; Hamilton, M.L. [Pacific Northwest National Laboratory, Richland, WA (United States)

    1996-04-01

    An effort is now underway to design an irradiation creep experiment involving SiC composites to SiC fibers. In order to successfully design such an experiment, it is necessary to review and assess the available data for monolithic SiC to establish the possible bounds of creep behavior for the composite. The data available show that monolithic SiC will indeed creep at a higher rate under irradiation compared to that of thermal creep, and surprisingly, it will do so in a temperature-dependant manner that is typical of metals.

  19. Monolithic Parallel Tandem Organic Photovoltaic Cell with Transparent Carbon Nanotube Interlayer

    Science.gov (United States)

    Tanaka, S.; Mielczarek, K.; Ovalle-Robles, R.; Wang, B.; Hsu, D.; Zakhidov, A. A.

    2009-01-01

    We demonstrate an organic photovoltaic cell with a monolithic tandem structure in parallel connection. Transparent multiwalled carbon nanotube sheets are used as an interlayer anode electrode for this parallel tandem. The characteristics of front and back cells are measured independently. The short circuit current density of the parallel tandem cell is larger than the currents of each individual cell. The wavelength dependence of photocurrent for the parallel tandem cell shows the superposition spectrum of the two spectral sensitivities of the front and back cells. The monolithic three-electrode photovoltaic cell indeed operates as a parallel tandem with improved efficiency.

  20. Novel design of low-jitter 10 GHz all-active monolithic mode-locked lasers

    DEFF Research Database (Denmark)

    Larsson, David; Yvind, Kresten; Christiansen, Lotte Jin

    2004-01-01

    Using a novel design, we have fabricated 10 GHz all-active monolithic mode-locked semiconductor lasers that generate 1.4 ps pulses with record-low timing jitter. The dynamical properties of lasers with 1 and 2 QWs are compared.......Using a novel design, we have fabricated 10 GHz all-active monolithic mode-locked semiconductor lasers that generate 1.4 ps pulses with record-low timing jitter. The dynamical properties of lasers with 1 and 2 QWs are compared....

  1. Ionic liquids as porogens in the microwave-assisted synthesis of methacrylate monoliths for chromatographic application

    Energy Technology Data Exchange (ETDEWEB)

    Singco, Brenda; Lin, Chen-Lan; Cheng, Yi-Jie; Shih, Yung-Han [Department of Chemistry and Center for Nanotechnology, CYCU (Chung Yuan Christian University), 200 Chung Pei Road, Chung-Li 320, Taiwan (China); Huang, Hsi-Ya, E-mail: hyhuang@cycu.edu.tw [Department of Chemistry and Center for Nanotechnology, CYCU (Chung Yuan Christian University), 200 Chung Pei Road, Chung-Li 320, Taiwan (China)

    2012-10-09

    Highlights: Black-Right-Pointing-Pointer An efficient and cleaner monoliths preparation utilizing ionic liquids in conjunction with microwave Black-Right-Pointing-Pointer These ionic liquids with varied cation alkyl chain and anion type successfully tuned the morphology of different alkyl methacrylates Black-Right-Pointing-Pointer Small molecules and peptide digests separated well in these monoliths. - Abstract: Several imidazolium-based ionic liquids (ILs) with varying cation alkyl chain length (C{sub 4}-C{sub 10}) and anion type (tetrafluoroborate ([BF{sub 4}]{sup -}), hexafluorophosphate ([PF{sub 6}]{sup -}) and bis(trifluoromethylsulfonyl)imide ([Tf{sub 2}N]{sup -})) were used as reaction media in the microwave polymerization of methacrylate-based stationary phases. Scanning electron micrographs and backpressures of poly(butyl methacrylate-ethylene dimethacrylate) (poly(BMA-EDMA)) monoliths synthesized in the presence of these ionic liquids demonstrated that porosity and permeability decreased when cation alkyl chain length and anion hydrophobicity were increased. Performance of these monoliths was assessed for their ability to separate parabens by capillary electrochromatography (CEC). Intra-batch precision (n = 3 columns) for retention time and peak area ranged was 0.80-1.13% and 3.71-4.58%, respectively. In addition, a good repeatability of RSD{sub Retentiontime} = <0.30% and {approx}1.0%, RSD{sub Peakarea} = <1.30% and <4.3%, and RSD{sub Efficiency} = <0.6% and <11.5% for intra-day and inter-day, respectively exemplify monolith performance reliability for poly(BMA-EDMA) fabricated using 1-hexyl-3-methylimidazolium tetrafluoroborate ([C{sub 6}mim][BF{sub 4}]) porogen. This monolith was also tested for its potential in nanoLC to separate protein digests in gradient mode. ILs as porogens also fabricated different alkyl methacrylate (AMA) (C4-C18) monoliths. Furthermore, employing binary IL porogen mixture such as 1-butyl-3-methylimidazolium tetrafluoroborate

  2. Macroporous Titania Monolith Prepared via Sol-gel Process with Polymer Foam as the Template

    Institute of Scientific and Technical Information of China (English)

    REN, Jian; DU, Zhong-Jie; ZHANG, Chen; LI, Hang-Quan

    2006-01-01

    Macroporous titania monoliths were prepared via sol-gel method using polymer foam as templates. The polymer foam polymerized via concentrated emulsion polymerization was immerged in a solution of titanium(Ⅳ) isopropoxide in 2-propanol, which underwent a sol-gel process. The organic components were subsequently removed by calcination. The effects of various parameters, including the nature of the monomer, the volume fraction of dispersed phase of the concentrated emulsion, and concentration of the sol-gel solution were investigated. The SEM micrographs of the macroporous titania monoliths thus obtained showed that the porous structure of the final material was effectively controllable.

  3. Transverse modes of a diode-laser pumped monolithic unidirectional non-planar ring laser

    Institute of Scientific and Technical Information of China (English)

    Keying Wu(吴克瑛); Suhui Yang(杨苏辉); Guanghui Wei(魏光辉)

    2003-01-01

    Diode-laser pumped monolithic single-frequency non-planar ring laser has the advantages of compactness,reliability and high efficiency. But when the pump power is high enough, the thermal effect will be seriousand the high-order transverse modes will appear. Therefore the single-mode output power is limited. Inthis paper, the mechanism of generating the high-order transverse modes in the monolithic unidirectionalnon-planar ring cavity is analyzed using ray tracing method. The calculated results are in agreement withthe experiments.

  4. An Innovative Gas Sensor with On-Chip Reference Using Monolithic Twin Laser

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yong-Gang; TIAN Zhao-Bing; ZHANG Xiao-Jun; GU Yi; LI Ai-Zhen; ZHU Xiang-Rong; ZHENG Yan-Lan; LIU Sheng

    2007-01-01

    An innovative gas sensor with on-chip reference using a monolithic twin laser is proposed. In this sensor a monolithic twin laser generates two closer laser beams with slight different wavelengths alternatively, one photodiode is used to catch both absorption and reference signals by time division multiplexing. The detection of nitrous oxide adopting this scheme using a 2.1 μm antimonide laser and an InGaAs photodiode has been demonstrated experimentally with detection limit below 1 ppm. Using this on chip reference scheme the fluctuations from the optical path and devices can be compensated effectively; the sensor system is simplified distinctly.

  5. Fabrication of Monolithic Dye-Sensitized Solar Cell Using Ionic Liquid Electrolyte

    Directory of Open Access Journals (Sweden)

    Seigo Ito

    2012-01-01

    Full Text Available To improve the durability of dye-sensitized solar cells (DSCs, monolithic DSCs with ionic liquid electrolyte were studied. Deposited by screen printing, a carbon layer was successfully fabricated that did not crack or peel when annealing was employed beforehand. Optimized electrodes exhibited photovoltaic characteristics of 0.608 V open-circuit voltage, 6.90 cm−2 mA short-circuit current, and 0.491 fill factor, yielding 2.06% power conversion efficiency. The monolithic DSC using ionic liquid electrolyte was thermally durable and operated stably for 1000 h at 80°C.

  6. Fracture Strength of Aged Monolithic and Bilayer Zirconia-Based Crowns

    OpenAIRE

    Deborah Pacheco Lameira; Silva, Wilkens Aurélio Buarque e; Silva, Frederico Andrade e; De Souza, Grace M.

    2015-01-01

    The purpose of this study was to evaluate the effect of design and surface finishing on fracture strength of yttria-tetragonal zirconia polycrystal (Y-TZP) crowns in monolithic (1.5 mm thickness) and bilayer (0.8 mm zirconia coping and 0.7 mm porcelain veneer) configuration after artificial aging. Bovine incisors received crown preparation and Y-TZP crowns were manufactured using CAD/CAM technique, according to the following groups (n = 10): Polished monolithic zirconia crowns (PM); Glazed mo...

  7. Combining monolithic zirconia crowns, digital impressioning, and regenerative cement for a predictable restorative alternative to PFM.

    Science.gov (United States)

    Griffin, Jack D

    2013-03-01

    Advances in indirect esthetic materials in recent years have provided the dental profession higher levels of strength and esthetics than ever before with products like lithium disilicate and zirconium oxide. Providing excellent fit and versatile performance, and because there is no porcelain to delaminate, chip, or fracture, monolithic zirconia crowns have the potential to outperform other layered restorations such as porcelain-fused-to-metal (PFM). This review of monolithic zirconia highlights a clinical case in which all-zirconia restorations were combined with CAD/CAM technology for a successful esthetic restorative outcome.

  8. Monolithic Parallel Tandem Organic Photovoltaic Cell with Transparent Carbon Nanotube Interlayer

    Science.gov (United States)

    Tanaka, S.; Mielczarek, K.; Ovalle-Robles, R.; Wang, B.; Hsu, D.; Zakhidov, A. A.

    2009-01-01

    We demonstrate an organic photovoltaic cell with a monolithic tandem structure in parallel connection. Transparent multiwalled carbon nanotube sheets are used as an interlayer anode electrode for this parallel tandem. The characteristics of front and back cells are measured independently. The short circuit current density of the parallel tandem cell is larger than the currents of each individual cell. The wavelength dependence of photocurrent for the parallel tandem cell shows the superposition spectrum of the two spectral sensitivities of the front and back cells. The monolithic three-electrode photovoltaic cell indeed operates as a parallel tandem with improved efficiency.

  9. Novel preparation of monolithic imprinted columns for electrochromatographic separation by photopolymerization

    Institute of Scientific and Technical Information of China (English)

    Yu Ping Zhang; Guo Qiang Zuo; Wen Jun Gong; Yue E. Deng; Quan Ming Li

    2007-01-01

    A monolithic molecularly imprinted polymer with specific recognition ability for 4-hydroxybenzoic acid (4-HBA) was prepared by in situ photopolymerization, using methacrylic acid (MAA) as a functional monomer, ethylene glycol dimethacrylate (EDMA) as a cross-linking agent, toluene and isooctane as porogenic solvents and Irgacure 1800 as an initiator.Baseline separation of isomers of hydroxybenzoic acid was achieved in less than 8 min on this monolithic column using 4-HBA as template, but not on the blank polymer.Furthermore, some neutral compounds could also be baseline-separated on the imprinted polymer column in the mode of pressure-driven capillary electrochromatography.

  10. Long all-active monolithic mode-locked lasers with surface-etched bragg gratings

    OpenAIRE

    Larsson, David; Yvind, Kresten; Hvam, Jørn Märcher

    2007-01-01

    We have fabricated 4.4-mm-long monolithic InAlGaAsP–InP mode-locked lasers with integrated deeply surface etched distributed Bragg reflector (DBR) mirrors. The lasers produce 3.7-ps transform-limited Gaussian pulses with 10-mW average output power and 250-fs absolute timing jitter. The performance of the DBR lasers is compared to the performance of Fabry–PÉrot mode-locked lasers from the same wafer and to the performance of earlier reported long monolithic DBR mode-locked lasers and is found ...

  11. Non-oxidic nanoscale composites: single-crystalline titanium carbide nanocubes in hierarchical porous carbon monoliths.

    Science.gov (United States)

    Sonnenburg, Kirstin; Smarsly, Bernd M; Brezesinski, Torsten

    2009-05-07

    We report the preparation of nanoscale carbon-titanium carbide composites with carbide contents of up to 80 wt%. The synthesis yields single-crystalline TiC nanocubes 20-30 nm in diameter embedded in a hierarchical porous carbon matrix. These composites were generated in the form of cylindrical monoliths but can be produced in various shapes using modern sol-gel and nanocasting methods in conjunction with carbothermal reduction. The monolithic material is characterized by a combination of microscopy, diffraction and physisorption. Overall, the results presented in this work represent a concrete design template for the synthesis of non-oxidic nanoscale composites with high surface areas.

  12. Structure and properties of hybrid poly(2-hydroxyethyl methacrylate)/SiO2 monoliths

    DEFF Research Database (Denmark)

    Ji, Xiangling; Jiang, Shichun; Qiu, Xuepeng

    2003-01-01

    to HEMA, was varied between 100/0 and 0/100. Structural analysis was performed by IR and NMR. The NMR results indicated that the introduction of PHEMA in the silica networks gave rise to a lower degree of condensation of TEOS. The resulting monoliths showed more than 75% transmittance in the visible...... related to some degree of chemical crosslinking between the polymer and the silica moiety, which would greatly improve the thermal stability of such hybrid monoliths compared with a pure PHEMA....

  13. Pybox monolithic miniflow reactors for continuous asymmetric cyclopropanation reaction under conventional and supercritical conditions.

    Science.gov (United States)

    Burguete, M I; Cornejo, A; García-Verdugo, E; Gil, María J; Luis, S V; Mayoral, J A; Martínez-Merino, V; Sokolova, M

    2007-06-08

    Supported catalysts having pybox chiral moieties were prepared as macroporous monolithic miniflow systems. These catalysts are based on styrene-divinylbenzene polymeric backbones having different compositions and pybox chiral moieties. Their corresponding ruthenium complexes were tested for the continuous flow cyclopropanation reaction between styrene and ethyldiazoacetate (EDA) under conventional conditions and in supercritical carbon dioxide (scCO2). Ru-Pybox monolithic miniflow reactors not only provided a highly efficient and robust heterogeneous chiral catalyst but also allowed us to develop more environmental reaction conditions without sacrificing the global efficiency of the process.

  14. Long all-active monolithic mode-locked lasers with surface-etched bragg gratings

    DEFF Research Database (Denmark)

    Larsson, David; Yvind, Kresten; Hvam, Jørn Märcher

    2007-01-01

    We have fabricated 4.4-mm-long monolithic InAlGaAsP–InP mode-locked lasers with integrated deeply surface etched distributed Bragg reflector (DBR) mirrors. The lasers produce 3.7-ps transform-limited Gaussian pulses with 10-mW average output power and 250-fs absolute timing jitter. The performance...... of the DBR lasers is compared to the performance of Fabry–PÉrot mode-locked lasers from the same wafer and to the performance of earlier reported long monolithic DBR mode-locked lasers and is found to be better....

  15. Properties of InGaAs quantum dot saturable absorbers in monolithic mode-locked lasers

    DEFF Research Database (Denmark)

    Thompson, M.G.; Marinelli, C.; Chu, Y.

    Saturable absorbers properties are characterised in monolithic mode-locked InGaAs quantum dot lasers. We analyse the impact of weak quantum confined Stark effect, fast absorber recovery time and low absorber saturation power on the mode-locking performance.......Saturable absorbers properties are characterised in monolithic mode-locked InGaAs quantum dot lasers. We analyse the impact of weak quantum confined Stark effect, fast absorber recovery time and low absorber saturation power on the mode-locking performance....

  16. Single-Fiber Bidirectional Optical Data Links with Monolithic Transceiver Chips

    OpenAIRE

    Alexander Kern; Sujoy Paul; Dietmar Wahl; Ahmed Al-Samaneh; Rainer Michalzik

    2012-01-01

    We report the monolithic integration, fabrication, and electrooptical properties of AlGaAs-GaAs-based transceiver (TRx) chips for 850 nm wavelength optical links with data rates of multiple Gbit/s. Using a single butt-coupled multimode fiber (MMF), low-cost bidirectional communication in half- and even full-duplex mode is demonstrated. Two design concepts are presented, based on a vertical-cavity surface-emitting laser (VCSEL) and a monolithically integrated p-doped-intrinsic-n-doped (PIN) or...

  17. Carbon Mineral Ecology: Predicting the Undiscovered Minerals of Carbon

    Science.gov (United States)

    Hazen, R. M.; Hummer, D. R.; Downs, R. T.; Hystad, G.; Golden, J.

    2015-12-01

    The diversity and distribution of Earth's minerals through deep time reflects key events in our planet's crustal evolution. Studies in mineral ecology exploit mineralogical databases to document diversity-distribution relationships of minerals, which reveal that all carbon-bearing minerals, as well as subsets containing C with O, H, Ca, or Na, conform to Large Number of Rare Events (LNRE) distributions. LNRE models facilitate prediction of total mineral diversity, and thus point to minerals that exist on Earth but have not yet been discovered and described. Our model predicts that at least 548 C minerals exist on Earth today, indicating that at least 145 carbon-bearing mineral species have yet to be discovered. Furthermore, by analyzing subsets of the most common additional elements in carbon-bearing minerals (i.e., 378 C + O species; 282 C + H species; 133 C + Ca species; and 100 C + Na species), we predict that 129 of these missing carbon minerals contain oxygen, 118 contain hydrogen, 52 contain calcium, and more than 60 contain sodium. The majority of these as yet undescribed minerals are predicted to be hydrous carbonates, many of which may have been overlooked because they are colorless, poorly crystalized, and/or water-soluble. We propose the identities of plausible as yet undescribed carbon minerals, as well as search strategies for their discovery. Some of these minerals will be natural examples of known synthetic compounds, including carbides such as calcium carbide (CaC2), crystalline hydrocarbons such as pyrene (C16H10), and numerous oxalates, anhydrous carbonates, and hydrous carbonates. Many other missing carbon minerals will be isomorphs of known carbon minerals, notably of the more than 100 different hydrous carbonate structures. An understanding of Earth's "missing" minerals provides a more complete picture of geochemical processes that influence crustal evolution.

  18. Mineral processing of heavy mineral sands from Malawi and Malaysia

    OpenAIRE

    Mitchell, C J

    1992-01-01

    Processing of heavy mineral sands involves many techniques including gravity, magnetic and electrostatic separation. As part of a laboratory programme to develop effective mineral processing techniques, two mineral sands from Malawi and Malaysia were processed using the standard techniques, with emphasis placed on the Carpco electrostatic separator. These sands were initially characterised mineralogically by scanning electron microscopy (SEM), electron microprobe analysis (EPMA...

  19. Adsorption of RNA on mineral surfaces and mineral precipitates

    Science.gov (United States)

    Biondi, Elisa; Furukawa, Yoshihiro; Kawai, Jun

    2017-01-01

    The prebiotic significance of laboratory experiments that study the interactions between oligomeric RNA and mineral species is difficult to know. Natural exemplars of specific minerals can differ widely depending on their provenance. While laboratory-generated samples of synthetic minerals can have controlled compositions, they are often viewed as "unnatural". Here, we show how trends in the interaction of RNA with natural mineral specimens, synthetic mineral specimens, and co-precipitated pairs of synthetic minerals, can make a persuasive case that the observed interactions reflect the composition of the minerals themselves, rather than their being simply examples of large molecules associating nonspecifically with large surfaces. Using this approach, we have discovered Periodic Table trends in the binding of oligomeric RNA to alkaline earth carbonate minerals and alkaline earth sulfate minerals, where those trends are the same when measured in natural and synthetic minerals. They are also validated by comparison of co-precipitated synthetic minerals. We also show differential binding of RNA to polymorphic forms of calcium carbonate, and the stabilization of bound RNA on aragonite. These have relevance to the prebiotic stabilization of RNA, where such carbonate minerals are expected to have been abundant, as they appear to be today on Mars.

  20. Oxygen Extraction from Minerals

    Science.gov (United States)

    Muscatello, Tony

    2017-01-01

    Oxygen, whether used as part of rocket bipropellant or for astronaut life support, is a key consumable for space exploration and commercialization. In Situ Resource Utilization (ISRU) has been proposed many times as a method for making space exploration more cost effective and sustainable. On planetary and asteroid surfaces the presence of minerals in the regolith that contain oxygen is very common, making them a potential oxygen resource. The majority of research and development for oxygen extraction from minerals has been for lunar regolith although this work would generally be applicable to regolith at other locations in space. This presentation will briefly survey the major methods investigated for oxygen extraction from regolith with a focus on the current status of those methods and possible future development pathways. The major oxygen production methods are (1) extraction from lunar ilmenite (FeTiO3) with either hydrogen or carbon monoxide, (2) carbothermal reduction of iron oxides and silicates with methane, and (3) molten regolith electrolysis (MRE) of silicates. Methods (1) and (2) have also been investigated in a two-step process using CO reduction and carbon deposition followed by carbothermal reduction. All three processes have byproducts that could also be used as resources. Hydrogen or carbon monoxide reduction produce iron metal in small amounts that could potentially be used as construction material. Carbothermal reduction also makes iron metal along with silicon metal and a glass with possible applications. MRE produces iron, silicon, aluminum, titanium, and glass, with higher silicon yields than carbothermal reduction. On Mars and possibly on some moons and asteroids, water is present in the form of mineral hydrates, hydroxyl (-OH) groups on minerals, andor water adsorbed on mineral surfaces. Heating of the minerals can liberate the water which can be electrolyzed to provide a source of oxygen as well. The chemistry of these processes, some key

  1. Components for monolithic fiber chirped pulse amplification laser systems

    Science.gov (United States)

    Swan, Michael Craig

    % respectively. With the inherent design tradeoff between the fundamental mode loss and higher order mode suppression, loss effects on system efficiency in different configurations were investigated. From these investigations it was seen that the slope-efficiency depends only on the total loss of the active fiber, and that when loss is present, the counter-propagating configuration has substantial advantages over the co-propagating case. In this thesis chirally-coupled-core fiber as the technological basis for the next generation of monolithic high power fiber laser systems has been established.

  2. Marine minerals: The Indian perspective

    Digital Repository Service at National Institute of Oceanography (India)

    Gujar, A.R.; Nath, B.N.; Banerjee, R.

    The sea floor of the continental margins of India is covered by a wide variety of terrigenous, biogenous, and chemogenous mineral deposits. Terrigenous heavy mineral placers containing ilmenite, magnetite, monazite, zircon, and rutile are reported...

  3. Unmixing of spectrally similar minerals

    CSIR Research Space (South Africa)

    Debba, Pravesh

    2009-01-01

    Full Text Available -bearing oxide/hydroxide/sulfate minerals in complex mixtures be obtained using hyperspectral data? Debba (CSIR) Unmixing of spectrally similar minerals MERAKA 2009 3 / 18 Method of spectral unmixing Old method: problem Linear Spectral Mixture Analysis (LSMA...

  4. Agricultural Minerals Operations - Direct Download

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This map layer includes agricultural minerals operations in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  5. Construction Minerals Operations - Direct Download

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This map layer includes construction minerals operations in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  6. Monolith ERP and current IT-trends : Creating a step by step development model (SSDM) for existing monolith ERP system to adapt to the current IT-trends

    OpenAIRE

    Vuorenmaa, Riku

    2015-01-01

    ERP systems have been around for 25 years and have gone through evolution phases. None of the previous phases have however imposed so big a challenge and opportunities for the ERP producers / vendors as current outsourcing and cloud computing trends. Current traditional on-premises (monolith) ERP systems are put under pressure to cope with the demands imposed by cloud computing and other IT-trends (such as mobility). Traditional ERP systems have to adapt or face a risk of becoming obsolete. ...

  7. Discussion on Nontraditional Mineral Resources

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In this paper, the authors introduce the concept of nontraditional mineral resources, and pro pose the major system of nontraditional mineral resources, including nontraditional resources, research methods, mining and mineral economics. Then the authors conclude that the research on nontraditional mineral resources is not only significant to satisfication the human needs in the 21st century, but also important to the development of the present geological theory.

  8. Aggregates from mineral wastes

    Directory of Open Access Journals (Sweden)

    Baic Ireneusz

    2016-01-01

    Full Text Available The problem concerning the growing demand for natural aggregates and the need to limit costs, including transportation from remote deposits, cause the increase in growth of interest in aggregates from mineral wastes as well as in technologies of their production and recovery. The paper presents the issue related to the group of aggregates other than natural. A common name is proposed for such material: “alternative aggregates”. The name seems to be fully justified due to adequacy of this term because of this raw materials origin and role, in comparison to the meaning of natural aggregates based on gravel and sand as well as crushed stones. The paper presents characteristics of the market and basic application of aggregates produced from mineral wastes, generated in the mining, power and metallurgical industries as well as material from demolished objects.

  9. Rock and mineral magnetism

    CERN Document Server

    O’Reilly, W

    1984-01-01

    The past two decades have witnessed a revolution in the earth sciences. The quantitative, instrument-based measurements and physical models of. geophysics, together with advances in technology, have radically transformed the way in which the Earth, and especially its crust, is described. The study of the magnetism of the rocks of the Earth's crust has played a major part in this transformation. Rocks, or more specifically their constituent magnetic minerals, can be regarded as a measuring instrument provided by nature, which can be employed in the service of the earth sciences. Thus magnetic minerals are a recording magnetometer; a goniometer or protractor, recording the directions of flows, fields and forces; a clock; a recording thermometer; a position recorder; astrain gauge; an instrument for geo­ logical surveying; a tracer in climatology and hydrology; a tool in petrology. No instrument is linear, or free from noise and systematic errors, and the performance of nature's instrument must be assessed and ...

  10. Iodine mineral waters

    Directory of Open Access Journals (Sweden)

    Iluta Alexandru

    2011-11-01

    Full Text Available Iodine mineral waters are found especially in sub-Carpathian region, also in regions with Salif deposits. Waters are currently used iodine in drinking cure for chaps and Basedow. Are also indicated in balneology. Iodine water containing at least 1 mg L, there is pure iodine is usually given the nature of other types of mineral waters further: sodium chlorinated water (Bazna (50-70 mg iodine / l, Baile Govora (50 - 70 mg / l, Bălţăteşti (4-5 mg / l, salted Monteoru (30 mg / l, mine water mixed alkaline chlorination, sulphate, which are indicated for crenoterapie (hypo or isotonic to the bathrooms Olăneşti or Călimăneşti-Căciulata.

  11. Coastal placer minerals

    Digital Repository Service at National Institute of Oceanography (India)

    Iyer, S.D.; Gujar, A.R.

    by mechanical concentration and natural gravity separation of mineral particles derived from weathered rocks. The formation of placers requires factors such as: climate, source rock, weathering, transport, deposition, concentration, high specific gravity... and transport of the rocks. For example, in cold and glaciated regions, there would be limited physical weathering and less concentration and more dispersion of the weathered material and placers would not FE AT U R E FE AT U R E A RT IC LE form...

  12. Mineral metabolism in cats

    OpenAIRE

    Pineda Martos, Carmen María

    2014-01-01

    The present Doctoral Thesis wa metabolism in the feline species. Through a series of studies, the relationship between calcium metabolism and the main hormones involved in it has been determined metabolism during the juvenile stage of growing cats effects linked to feeding calculolytic diets on feline mineral metabolism. The first part of the work was aimed the quantification of intact (I-PTH) and whole PTH) and to characterize the dynamics of PTH secretion, including ...

  13. Culture systems: mineral oil overlay.

    Science.gov (United States)

    Morbeck, Dean E; Leonard, Phoebe H

    2012-01-01

    Mineral oil overlay microdrop is commonly used during in vitro fertilization (IVF) procedures. Though mineral oil appears homogeneous, it is an undefined product that can vary in quality. Here, we describe the history, chemistry, processing, and optimal use of mineral oil for IVF and embryo culture.

  14. Polymer-mediated mesoscale mineralization

    Institute of Scientific and Technical Information of China (English)

    CHEN ShaoFeng; YU ShuHong

    2009-01-01

    Polymer-controlled mineralization in aqueous solution or in a mixed solvent media, as well as its com-bination with the interface of air-water can lead to the formation of minerals with unique structures and morphologies, which sheds light on the possibility to mimic the detailed structures of the natural min-erals.

  15. Definitions of Health Terms: Minerals

    Science.gov (United States)

    ... this page: https://medlineplus.gov/definitions/mineralsdefinitions.html Definitions of Health Terms : Minerals To use the sharing features on ... of the minerals that you need. Find more definitions on Fitness | General Health | Minerals | Nutrition | Vitamins Antioxidants Antioxidants are substances that ...

  16. Refractory Minerals in Henan Province

    Institute of Scientific and Technical Information of China (English)

    JIN Qinguo; LI Jing; LIU Jiehua; LIU Yanjun

    2004-01-01

    Henan province is very rich in refractory minerals of many varieties including silica, dolomite, graphite,pearlite, sepiolite, olivine, and sillimanite group minerals, besides the abundant reserves of fireclay and bauxite,which lay a good foundation for the development of the refractories industry of the province. The paper introduces the reserves, distribution and character of the refractory minerals in Henan province.

  17. Computer Aided Design of Monolithic Microwave and Millimeter Wave Integrated Circuits and Subsystems

    Science.gov (United States)

    1989-05-01

    methods," SIAM J. as a Consultant to DOD on the VHSIC and various monolithic programs Numer. Anal., vol. 20, no. 3, pp. 510-536, 1983. and industrial ...algorithm," Acta Electronica Sinica. vol. 14, no. 4, pp. 91-96, 1986. Neglecting the higher order terms, we can express ,(x) 161 J. E. Dennis. Jr

  18. Development of a monolithic polymer pipette for solid-phase extraction of liquiritigenin in rat plasma

    Institute of Scientific and Technical Information of China (English)

    Hong Wu Zhang; Kang Li; Zhi Xian Liang; Feng Yang Wang; Qi Wen Lu

    2012-01-01

    A monolithic polymer column with mixed-mode interaction was prepared by in situ polymerization in a 1000 μ,L pipette.Two kinds of monomers,butyl methacrylate (BMA) and 2-(dimethylamino)ethyl methacrylate (DMAM) were applied to constructing the mixed-mode interaction of monolithic polymer column.Its solid-phase extraction properties for liquiritigenin (LQG) were evaluated by high performance liquid chromatography (HPLC) with a gradient elution procedure.After the extraction procedure was optimized,the maximum binding capacity and extraction recovery following the optimal extraction procedure were investigated.Calibration curve was expressed as A =65.9C + 4.53 (r2 =0.998) with a linear range of 0.151-1.80 μg/mL.The experimental results indicate that the monolithic polymer pipette presents good extraction efficiency for LQG.It can be envisaged that the developed monolithic polymer pipette possesses the potential for its application to the enrichment of other flavonoids compounds being siniilar to the structure of LQG.

  19. Characteristics of an activated carbon monolith for a helium adsorption compressor

    NARCIS (Netherlands)

    Lozano-Castello, D.; Jorda-Beneyto, M.; Cazorla-Amoros, D.; Linares-Solano, A.; Burger, J.F.; Brake, ter H.J.M.; Holland, H.J.

    2010-01-01

    An activated carbon monolith (ACM) with a high helium adsorption/desorption capacity, high density, low pressure drop, low thermal expansion and good mechanical properties was prepared and applied successfully in a helium adsorption compressor as a part of a 4.5 K sorption cooler. The activated carb

  20. Monolithic dual-band HgCdTe infrared detector structure

    CSIR Research Space (South Africa)

    Parish, G

    1997-07-01

    Full Text Available A monolithic HgCdTe photoconductive device structure is presented that is suitable for dual-band optically registered infrared photodetection in the two atmospheric transmission windows of 3-5 mu m and 8-12 mu m, which correspond to the mid...

  1. Detection of ochratoxin A in beer samples with a label-free monolithically integrated optoelectronic biosensor

    NARCIS (Netherlands)

    Pagkali, Varvara; Petrou, Panagiota S.; Salapatas, Alexandros; Makarona, Eleni; Peters, Jeroen; Haasnoot, Willem; Jobst, Gerhard; Economou, Anastasios; Misiakos, Konstantinos; Raptis, Ioannis; Kakabakos, Sotirios E.

    2016-01-01

    An optical biosensor for label-free detection of ochratoxin A (OTA) in beer samples is presented. The biosensor consists of an array of ten Mach-Zehnder interferometers (MZIs) monolithically integrated along with their respective broad-band silicon light sources on the same Si chip (37mm2

  2. Effect on mass transference phenomena by textural change inside monolithic carbon aerogels

    Science.gov (United States)

    Chejne, F.; Camargo-Trillos, D.; Pabón, E.; Carrasco-Marin, F.

    2015-08-01

    The effects on mass transference phenomena due textural changes of monolithic carbon aerogels were studied by hexane adsorption. The monolithic carbon aerogels were prepared after carbonization of the organic aerogels obtained by resorcinol-formaldehyde polymerization, using p-toluenesulfonic acid (acid-catalyst) and sodium carbonate catalysts (basic-catalyst). Internal texture was modified by CO2 activation. The characterization by gas adsorption showed that the monolithic carbon aerogels presents a bi-modal pore size distribution with presence of both microporous and mesoporous. It was shown that the activation process of monolithic carbon aerogels increases their micropore volume bigger than the other one acid-catalyst aerogel. The mesopores volume in the carbon aerogels plays an important role on mass transport mechanism. The samples with presence of significant mesopore volume present a lower height of mass transfer zone than others less mesopore volume; therefore better efficiency of adsorption in mass transfer zone in dynamic adsorption. The breakthrough curve methodology proposed in this work has allowed finding a relationship between the structural parameters and dynamic adsorption variables, which opens new approaches for measuring textural parameters of material.

  3. Monolithic Chip System with a Microfluidic Channel for In Situ Electron Microscopy of Liquids

    DEFF Research Database (Denmark)

    Jensen, Eric; Burrows, Andrew; Mølhave, Kristian

    2014-01-01

    sandwiched microchips with thin membranes. We report on a new microfabricated chip system based on a monolithic design that enables membrane geometry on the scale of a few micrometers. The design is intended to reduce membrane deflection when the system is under pressure, a micro fluidic channel for improved...

  4. Solid State Characterizations of Long-Term Leached Cast Stone Monoliths

    Energy Technology Data Exchange (ETDEWEB)

    Asmussen, Robert M.; Pearce, Carolyn I.; Parker, Kent E.; Miller, Brian W.; Lee, Brady D.; Buck, Edgar C.; Washton, Nancy M.; Bowden, Mark E.; Lawter, Amanda R.; McElroy, Erin M.; Serne, R Jeffrey

    2016-09-30

    This report describes the results from the solid phase characterization of six Cast Stone monoliths from the extended leach tests recently reported on (Serne et al. 2016),that were selected for characterization using multiple state-of-the-art approaches. The Cast Stone samples investigated were leached for > 590 d in the EPA Method 1315 test then archived for > 390 d in their final leachate. After reporting the long term leach behavior of the monoliths (containing radioactive 99Tc and stable 127I spikes and for original Westsik et al. 2013 fabricated monoliths, 238U), it was suggested that physical changes to the waste forms and a depleting inventory of contaminants of potential concern may mean that effective diffusivity calculations past 63 d should not be used to accurately represent long-term waste form behavior. These novel investigations, in both length of leaching time and application of solid state techniques, provide an initial arsenal of techniques which can be utilized to perform such Cast Stone solid phase characterization work, which in turn can support upcoming performance assessment maintenance. The work was performed at Pacific Northwest National Laboratory (PNNL) for Washington River Protection Solutions (WRPS) to characterize several properties of the long- term leached Cast Stone monolith samples.

  5. Radiation Tolerance of CMOS Monolithic Active Pixel Sensors with Self-Biased Pixels

    CERN Document Server

    Deveaux, M; Besson, A; Claus, G; Colledani, C; Dorokhov, M; Dritsa, C; Dulinski, W; Fröhlich, I; Goffe, M; Grandjean, D; Heini, S; Himmi, A; Hu, C; Jaaskelainen, K; Müntz, C; Shabetai, A; Stroth, J; Szelezniak, M; Valin, I; Winter, M

    2009-01-01

    CMOS Monolithic Active Pixel Sensors (MAPS) are proposed as a technology for various vertex detectors in nuclear and particle physics. We discuss the mechanisms of ionizing radiation damage on MAPS hosting the the dead time free, so-called self bias pixel. Moreover, we discuss radiation hardened sensor designs which allow operating detectors after exposing them to irradiation doses above 1 Mrad

  6. Improved Nearest Neighbor Methods for Gamma Photon Interaction Position Determination in Monolithic Scintillator PET Detectors

    NARCIS (Netherlands)

    van Dam, Herman T.; Seifert, Stefan; Vinke, Ruud; Dendooven, Peter; Lohner, Herbert; Beekman, Freek J.; Schaart, Dennis R.

    2011-01-01

    Monolithic scintillator detectors have been shown to provide good performance and to have various practical advantages for use in PET systems. Excellent results for the gamma photon interaction position determination in these detectors have been obtained by means of the k-nearest neighbor (k-NN)

  7. Ionic liquid-based zwitterionic organic polymer monolithic column for capillary hydrophilic interaction chromatography.

    Science.gov (United States)

    Wang, Tingting; Chen, Yihui; Ma, Junfeng; Zhang, Xiaodan; Zhang, Lihua; Zhang, Yukui

    2015-08-21

    In the current study, a novel ionic liquid-based zwitterionic organic polymer monolithic column was developed by copolymerizing 1-vinyl-3-(butyl-4-sulfonate) imidazolium, acrylamide and N,N'-methylenebisacrylamide in a quaternary porogenic solvent consisting of formamide, dimethyl sulphoxide, polyethylene glycol 8000 and polyethylene glycol 10,000 for capillary hydrophilic interaction chromatography. The monolithic stationary phase was optimized by adjusting the amount of monomer in the polymerization solution along with the composition of porogenic solvent. The optimized monolith exhibited excellent selectivity and favorable retention for nucleosides and benzoic acid derivatives. The primary factors affecting the separation efficiency of the monolithic column (including acetonitrile content, pH, and buffer salt concentration in the mobile phase) have been thoroughly evaluated. Excellent reproducibility of the retention times for five nucleosides was achieved, with relative standard deviations of run-to-run (n = 3), column-to-column (n = 3) and batch-to-batch (n = 3) in the range of 0.18-0.48%, 2.33-4.20% and 3.07-6.50%, respectively.

  8. Preparation and evaluation of monolithic molecularly imprinted stationary phase for S-naproxen

    Institute of Scientific and Technical Information of China (English)

    De-Miao Chen; Qiang Fu; Wei Du; Si-Juan Sun; Ping Huang; Chun Chang

    2011-01-01

    An S-naproxen(S-NAP)molecularly imprinted monolithic stationary phase(MIMSP)with specific recognition for S-NAP and naproxen(NAP)was prepared by in situ technique,utilizing 4-vinylpridine(4-VP)as a function monomer,ethylene glycol dimethacrylate(EDMA)as a

  9. Monolithic integration of DUV-induced waveguides into plastic microfluidic chip for optical manipulation

    DEFF Research Database (Denmark)

    Khoury Arvelo, Maria; Vannahme, Christoph; Sørensen, Kristian Tølbøl

    2014-01-01

    A monolithic polymer optofluidic chip for manipulation of microbeads in flow is demonstrated. On this chip, polymer waveguides induced by Deep UV lithography are integrated with microfluidic channels. The optical propagation losses of the waveguides are measured to be 0.66±0.13 d...

  10. HVCMOS Monolithic Sensors for the High Luminosity Upgrade of ATLAS Experiment

    Science.gov (United States)

    Blanco, R.; Zhang, H.; Krämer, C.; Ehrler, F.; Schimassek, R.; Casanova Mohr, R.; Vilella Figueras, E.; Guezzi Messaoud, F.; Leys, R.; Prathapan, M.; Weber, A.; Perić, I.

    2017-04-01

    This paper describes several monolithic pixel detector designs implemented in a high-voltage CMOS technology. The total size of all chips is 1cm × 1cm. The pixel matrices are distinguished by the readout cell type, the pixel type and the pixel address multiplexing. Design details and first measurement results are described.

  11. Automation of the Technological Process to Produce Building Frame-Monolithic Modules Based on Fluoranhydrite

    Science.gov (United States)

    Fedorchuk, J.; Sadenova, M.; Rusina, O.

    2016-01-01

    The paper first proposes the automation of the technological process to produce building frame-monolithic modules from production wastes, namely technogenic anhydrite and fluoranhydrite. A functional diagram of the process automation is developed, the devices to perform control and maintenance with account of the production characteristics are chosen.

  12. Phased-Array Monolithic PEM for FT Spectrometry With Applications in Explosive Detection and CB Defense

    Science.gov (United States)

    2008-12-01

    1 PHASED-ARRAY MONOLITHIC PEM FOR FT SPECTROMETRY WITH APPLICATIONS IN EXPLOSIVE DETECTION AND CB DEFENSE Tudor N. Buican* Semiotic ...PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Semiotic Engineering Associates LLC Albuquerque, NM 87108 8. PERFORMING ORGANIZATION REPORT NUMBER 9

  13. ZIC-HILIC monolithic capillary column coupled with MALDI-MS: A tool for glycan analysis

    OpenAIRE

    Šesták, J. (Jozef); Křenková, J. (Jana); Moravcová, D. (Dana); Planeta, J. (Josef); Kahle, V. (Vladislav)

    2014-01-01

    In this contribution, we report analysis of glycans enzymatically released from bovine ribonuclease B (RNase B) and human immunoglobulin G (hIgG) combining glycan separation using the synthesized zwitterionic silica-based monolithic capillary column and off-line MALDI-MS detection.

  14. Detection of ochratoxin A in beer samples with a label-free monolithically integrated optoelectronic biosensor

    NARCIS (Netherlands)

    Pagkali, Varvara; Petrou, Panagiota S.; Salapatas, Alexandros; Makarona, Eleni; Peters, Jeroen; Haasnoot, Willem; Jobst, Gerhard; Economou, Anastasios; Misiakos, Konstantinos; Raptis, Ioannis; Kakabakos, Sotirios E.

    2017-01-01

    An optical biosensor for label-free detection of ochratoxin A (OTA) in beer samples is presented. The biosensor consists of an array of ten Mach-Zehnder interferometers (MZIs) monolithically integrated along with their respective broad-band silicon light sources on the same Si chip (37mm2

  15. Fully integrated monolithic opoelectronic transducer for real.time protein and DNA detection

    DEFF Research Database (Denmark)

    Misiakos, Konstatinos; S. Petrou, Panagiota; E. Kakabakos, Sotirios

    2010-01-01

    The development and testing of a portable bioanalytical device which was capable for real-time monitoring of binding assays was demonstrated. The device was based on arrays of nine optoelectronic transducers monolithically integrated on silicon chips. The optocouplers consisted of nine silicon av...

  16. Thick monolithic scintillation crystals for TOF-PET with depth-of-interaction measurement

    NARCIS (Netherlands)

    Vinke, Ruud; van Dam, Herman T.; Seifert, Stefan; Beekman, Freek J.; Lohner, Herbert; Schaart, Dennis R.; Dendooven, Peter

    2010-01-01

    Positron emission tomography (PET) detectors based on monolithic scintillation crystals show excellent intrinsic spatial resolution and allow depth-of-interaction (DOI) reconstruction using a single photosensor array. The inclusion of time-of-flight (TOF) information in the image reconstruction

  17. Tunable mechanical monolithic sensor with interferometric readout for low frequency seismic noise measurement

    Science.gov (United States)

    Acernese, F.; De Rosa, R.; Giordano, G.; Romano, R.; Barone, F.

    2008-03-01

    This paper describes a mechanical monolithic sensor for geophysical applications developed at the University of Salerno. The instrument is basically a monolithic tunable folded pendulum, shaped with precision machining and electric-discharge-machining, that can be used both as seismometer and, in a force-feedback configuration, as accelerometer. The monolithic mechanical design and the introduction of laser interferometric techniques for the readout implementation make it a very compact instrument, very sensitive in the low-frequency seismic noise band, with a very good immunity to environmental noises. Many changes have been produced since last version (2007), mainly aimed to the improvement of the mechanics and of the optical readout of the instrument. In fact, we have developed and tested a prototype with elliptical hinges and mechanical tuning of the resonance frequency together with a laser optical lever and a new laser interferometer readout system. The theoretical sensitivity curve both for both laser optical lever and laser interferometric readouts, evaluated on the basis of suitable theoretical models, shows a very good agreement with the experimental measurements. Very interesting scientific result, for example, is that the measured natural resonance frequency of the instrument is 70 mHz with a Q = 140 in air without thermal stabilization, demonstrating the feasibility of a monolithic FP sensor with a natural resonance frequency of the order of mHz with a more refined mechanical tuning. Results on the readout system based on polarimetric homodyne Michelson interferometer is discussed.

  18. Monolithic Multi-Colour 40 GHz Mode-Locked Laser Array

    OpenAIRE

    Hou, Lianping; Eddie, Iain; Marsh, John

    2016-01-01

    The monolithic integration of four 40 GHz multi-colored mode-locked lasers with a 4×1 MMI, four electroabsorption modulators and an SOA has been demonstrated. The shortest pulse widths are between 2.63 and 2.85 ps.

  19. 5Gb/s optical logic AND operations using by monolithically integrated photodiode and electroabsorption modulator

    Science.gov (United States)

    Zhang, Y. X.; Zhao, L. J.; Niu, B.; Pan, J. Q.; Wang, W.

    2010-05-01

    A novel EAM/PD monolithically-integrated optical logic element is presented. 5Gb/s optical logic AND gate operations at about -2 V for non-return-to-zero (NRZ) signals with8.4dB extinction ratio and16mW absorbed optical power was demonstrated.

  20. Application of Reliability Analysis for Optimal Design of Monolithic Vertical Wall Breakwaters

    DEFF Research Database (Denmark)

    Burcharth, H. F.; Sørensen, John Dalsgaard; Christiani, E.

    1995-01-01

    Reliability analysis and reliability-based design of monolithic vertical wall breakwaters are considered. Probabilistic models of some of the most important failure modes are described. The failures are sliding and slip surface failure of a rubble mound and a clay foundation. Relevant design...... variables are identified and a reliability-based design optimization procedure is formulated. Results from an illustrative example are given....

  1. Integrated on-chip mass spectrometry reaction monitoring in microfluidic devices containing porous polymer monolithic columns.

    Science.gov (United States)

    Dietze, C; Schulze, S; Ohla, S; Gilmore, K; Seeberger, P H; Belder, D

    2016-09-21

    Chip-based microfluidics enable the seamless integration of different functions into single devices. Here, we present microfluidic chips containing porous polymer monolithic columns as a means to facilitate chemical transformations as well as both downstream chromatographic separation and mass spectrometric analysis. Rapid liquid phase lithography prototyping creates the multifunctional device economically.

  2. Monolithic liquid-chromatography columns for protein analysisprotein digest separation and integrated systems

    NARCIS (Netherlands)

    van de Meent, M.H.M.

    2010-01-01

    The objectives of the research described in this thesis are to evaluate the applicability of both silica-based and polymeric monolithic columns for protein analysis. The first part describes investigations into the effects of column length and stationary-phase chemistry on the separation of protein

  3. Preparation, characterization and application of organic-inorganic hybrid caffeine imprinted monolith.

    Science.gov (United States)

    Liu, Xiaofang; Sun, Na; Zhu, Quanfei; Wu, Mei; Ye, Yong; Chen, Huaixia

    2013-08-23

    The present work aims to synthesize an organic-inorganic hybrid caffeine imprinted monolith using one-step method. The synthesis conditions such as the type of inorganic precursor and porogenic solvent, the molar ratios of the monomer and cross-linker, the volume ratio of the inorganic alcoholysate and organic part were optimized. The morphology of the monolith was studied by scanning electron microscopy and Fourier transform infrared spectra. The imprinted factor of the monolith for caffeine reached 3.02. A simple, rapid and sensitive method for the determination of caffeine in children's milk using the organic-inorganic hybrid caffeine imprinted polymer monolith microextraction combined with high-performance liquid chromatography-photodiodes array detector was developed. Several parameters affecting the sample pretreatment were investigated, including the type, flow rate and volume of eluent, the flow rate and volume of sample solution. The assay exhibited a linear dynamic range of 8-500μgL(-1) with the correlation coefficient above 0.9987. Lower limits of detection (LOD, at S/N=3) and quantification (LOQ, at S/N=10) in children's milk samples were 2.7 and 8μgL(-1). Recoveries of caffeine from spiked children's milk ranged from 85 to 104% with relative standard deviations of less than 8.9%.

  4. Capillary Electrochromatography of Molecularly Imprinted Monolithic Column Using p-Hydroxybenzoic Acid as Templates

    Institute of Scientific and Technical Information of China (English)

    Zhao Sheng LIU; Yan Li XU; Chao YAN; Ru Yu GAO

    2004-01-01

    Molecularly imprinted polymers using p-hydroxybenzoic acid as templates was synthesized by an in situ polymerization reaction and rendered capillary monolithic column was used in capillary electrochromatographic mode. Good molecular recognition was achieved forphydroxybenzoic acid and good resolution of isomers can be realized.

  5. Preparation of a thermoresponsive polymer grafted polystyrene monolithic capillary for the separation of bioactive compounds.

    Science.gov (United States)

    Koriyama, Takuya; Asoh, Taka-Aki; Kikuchi, Akihiko

    2016-11-01

    To develop aqueous microseparation columns for bioactive compounds, a thermoresponsive polymer grafted polymer monolith was prepared inside silica capillaries having an I.D. of 100μm by polymerization of styrene (St) with m/p-divinylbenzene (DVB) in the presence of polydimethylsiloxane as porogen, followed by surface-initiated atom transfer radical polymerization (SI-ATRP) of N-isopropylacrylamide (NIPAAm). SEM analysis indicated that the resulting poly(N-isopropylacrylamide) (PNIPAAm) grafted polystyrene monolith had a consecutive three-dimensionally interconnected structure and through-pores, similar to the base polystyrene (PSt) monolith. The elution behavior of steroids with different hydrophobicity was evaluated using micro-high-performance liquid chromatography in sole aqueous mobile phase. Temperature dependent interaction changes were observed between steroids and the PNIPAAm modified surfaces. Furthermore, the interaction between bioactive compounds and the PNIPAAm grafted PSt surfaces was controlled and eventually separate these molecules with different hydrophobicities by simple temperature modulation in aqueous environment. The PNIPAAm grafted PSt monolithic capillary showed improved separation properties of bioactive compounds, compared with a PNIPAAm grafted hollow capillary in aqueous environment.

  6. Low-Loss 256-Channel AWG Module with Monolithically Integrated Spot-Size Converters

    Institute of Scientific and Technical Information of China (English)

    M. Itoh; S. Kamei; M. Ishii; Y. Hida; T. Shibata; Y. Hibino

    2003-01-01

    We developed a compact fiber-pigtailed 256-channel AWG module with 1.5% △ waveguides.By monolithically integrating spot-size converters with input/output waveguides, we achieved a lowinsertion loss of 2.6-4.1 dB with a low background crosstalk of -40 dB.

  7. Low-Loss 256-Channel AWG Module with Monolithically Integrated Spot-Size Converters

    Institute of Scientific and Technical Information of China (English)

    M.; Itoh; S.; Kamei; M.; Ishii; Y.; Hida; T.; Shibata; Y.; Hibino

    2003-01-01

    We developed a compact fiber-pigtailed 256-channel AWG module with 1.5% A waveguides. By monolithically integrating spot-size converters with input/output waveguides, we achieved a low insertion loss of 2.6-4.1 dB with a low background crosstalk of-40 dB.

  8. Preparation and evaluation of a novel hybrid monolithic column based on pentafluorobenzyl imidazolium bromide ionic liquid.

    Science.gov (United States)

    Shan, Yuanhong; Qiao, Lizhen; Shi, Xianzhe; Xu, Guowang

    2015-01-02

    To develop a novel hybrid monolithic column based on pentafluorobenzyl imidazolium bromide ionic liquid, a new ionic liquid monomer was synthesized from 1-vinylimidazole and pentafluorobenzyl bromide. By employing a facile one-step copolymerization of polyhedral-oligomeric-silsesquioxane-type (POSS) cross-linking agent and the home-made ionic liquid monomer, the hybrid monolithic columns were in situ fabricated in fused-silica capillary. The morphology of monolithic column was characterized by scanning electron microscope (SEM) and the chemical composition was confirmed by Fourier-transform infrared spectroscopy (FT-IR) and elemental analysis. Excellent mechanical stability and slight swelling propensity were exhibited which was ascribed to the rigid hybrid monolithic skeleton. Reproducibility results of run-to-run, column-to-column, batch-to-batch and day-to-day were investigated and the RSDs were less than 0.46%, 1.84%, 3.96% and 3.17%, respectively. The mixed-mode retention mechanism with hydrophobic interaction, π-π stacking, ion-exchange, electrostatic interaction and dipole-dipole interaction was explored systematically using analytes with different structure types. Satisfied separation capability and column efficiency were achieved for the analysis of small molecular compounds such as alkylbenzenes, polycyclic aromatic hydrocarbons, nucleosides and halogenated compounds. Copyright © 2014 Elsevier B.V. All rights reserved.

  9. Monolithic columns with organic sorbent based on poly-1-vinylimidazole for high performance liquid chromatography

    Science.gov (United States)

    Patrushev, Y. V.; Sidelnikov, V. N.; Yudina, Y. S.

    2017-03-01

    Monolithic chromatographic columns for HPLC with sorbent based on 1-vinylimidazole are prepared. It is shown that changing the 1-vinylimidazole content in the initial solution allows us to change the polarity of columns. An example of aromatic hydrocarbons separation is presented.

  10. Monolithic integration of electroabsorption modulators and tunnel injection distributed feedback lasers using quantum well intermixing

    Science.gov (United States)

    Wang, Yang; Pan, Jiao-Qing; Zhao, Ling-Juan; Zhu, Hong-Liang; Wang, Wei

    2010-12-01

    Electroabsorption modulators combining Franz-Keldysh effect and quantum confined Stark effect have been monolithically integrated with tunnel-injection quantum-well distributed feedback lasers using a quantum well intermixing method. Superior characteristics such as extinction ratio and temperature insensitivity have been demonstrated at wide temperature ranges.

  11. A monolithic relativistic electron beam source based on a dielectric laser accelerator structure

    Energy Technology Data Exchange (ETDEWEB)

    McNeur, Josh; Carranza, Nestor; Travish, Gil; Yin Hairong; Yoder, Rodney [UCLA Dept. of Physics and Astronomy, Los Angeles, CA 90095 (United States); College of Physical Electronics, University of Electronic Science and Technology of China, Chengdu, Sichuan, 610054 (China); Manhattanville College, Physics Dept., 2900 Purchase St., Purchase, NY 10577 (United States)

    2012-12-21

    Work towards a monolithic device capable of producing relativistic particle beams within a cubic-centimeter is detailed. We will discuss the Micro-Accelerator Platform (MAP), an optical laser powered dielectric accelerator as the main building block of this chip-scale source along with a field enhanced emitter and a region for sub-relativistic acceleration.

  12. First acidic macro-mesocellular aluminosilicate monolithic foams "SiAl(HIPE)" and their catalytic properties.

    Science.gov (United States)

    Debecker, Damien P; Boissière, Cédric; Laurent, Guillaume; Huet, Stéphanie; Eliaers, Philippe; Sanchez, Clément; Backov, Rénal

    2015-09-25

    A new type of acidic macrocellular and mesoporous silica-alumina foam is obtained via a one pot alkaline sol-gel route coupled with a concentrated emulsion-based templating technique. The mixed oxide monolith exhibits high surface acidity, translating into excellent performance in the acid-catalyzed dehydration of bioethanol to ethene.

  13. RELATIVE TRACE MINERAL BIOAVAILABILITY

    Directory of Open Access Journals (Sweden)

    Rchard D. Miles

    2006-10-01

    Full Text Available Para determinar a eficiência de utilização de elementos minerais dietéticos, deve-se conhecer a biodisponibilidade relativa de cada elemento de um determinado ingrediente ou de uma ração completa. Análises químicas da dieta ou de um determinado ingrediente não indicam a efetividade biológica de um nutriente. Existem muitos fatores que influenciam a biodisponibilidade dos minerais, especialmente dos minerais-traço, tais como: nível de consumo do mineral, forma química, digestibilidade da dieta, tamanho da partícula, interações com outros minerais e nutrientes, agentes quelantes, inibidores, estado fisiológico do animal, qualidade da água, condições de processamento ao qual ingredientes individuais ou uma dieta completa foram expostos e, é óbvio, a idade e a espécie animal. Quando um mineral-traço é ingerido, sua biodisponibilidade é influenciada por propriedades específicas do mineral da maneira como está incluído na dieta. Por exemplo, sua valência e forma molecular (orgânica versus inorgânica são importantes. Por causa dessas propriedades específicas, o mineral pode formar complexos com outros componentes no intestino, o que pode dificultar ou facilitar a absorção pela mucosa, o transporte ou o metabolismo do mineral no organismo. É bem conhecido que certos minerais em sua forma inorgânica competem com outros minerais por sítios de ligação e por absorção no intestino. O conhecimento sobre a biodisponibilidade dos minerais-traço nos ingredientes e fontes suplementares é importante para a formulação econômica de uma ração para garantir ótimo desempenho animal. A biodisponibilidade deve ser entendida como um valor “estimado” que reflete a absorção e a utilização do mineral sobre condições de um experimento específico e não de uma propriedade inerente e específica de um ingrediente ou suplemento de ração. Com a tecnologia disponível, a determinação da biodisponibilidade dentro de

  14. Mass transfer kinetic mechanism in monolithic columns and application to the characterization of new research monolithic samples with different average pore sizes.

    Science.gov (United States)

    Gritti, Fabrice; Guiochon, Georges

    2009-06-01

    A general reduced HETP (height equivalent to a theoretical plate) equation is proposed that accounts for the mass transfer of a wide range of molecular weight compounds in monolithic columns. The detailed derivatization of each one of the individual and independent mass transfer contributions (longitudinal diffusion, eddy dispersion, film mass transfer resistance, and trans-skeleton mass transfer resistance) is discussed. The reduced HETPs of a series of small molecules (phenol, toluene, acenaphthene, and amylbenzene) and of a larger molecule, insulin, were measured on three research grade monolithic columns (M150, M225, M350) having different average pore size (approximately 150, 225, and 350 A, respectively) but the same dimension (100 mm x 4.6 mm). The first and second central moments of 2 muL samples were measured and corrected for the extra-column contributions. The h data were fitted to the new HETP equation in order to identify which contribution controls the band broadening in monolithic columns. The contribution of the B-term was found to be negligible compared to that of the A-term, even at very low reduced velocities (numass transfer across the column. Experimental chromatograms exhibited variable degrees of systematic peak fronting, depending on the column studied. The heterogeneity of the distribution of eluent velocities from the column center to its wall (average 5%) is the source of this peak fronting. At high reduced velocities (nu>5), the C-term of the monolithic columns is controlled by film mass transfer resistance between the eluent circulating in the large throughpores and the eluent stagnant inside the thin porous skeleton. The experimental Sherwood number measured on the monolith columns increases from 0.05 to 0.22 while the adsorption energy increases by nearly 6 kJ/mol. Stronger adsorption leads to an increase in the value of the estimated film mass transfer coefficient when a first order film mass transfer rate is assumed (j proportional

  15. Poly(ethylenimine)-Functionalized Monolithic Alumina Honeycomb Adsorbents for CO2 Capture from Air.

    Science.gov (United States)

    Sakwa-Novak, Miles A; Yoo, Chun-Jae; Tan, Shuai; Rashidi, Fereshteh; Jones, Christopher W

    2016-07-21

    The development of practical and effective gas-solid contactors is an important area in the development of CO2 capture technologies. Target CO2 capture applications, such as postcombustion carbon capture and sequestration (CCS) from power plant flue gases or CO2 extraction directly from ambient air (DAC), require high flow rates of gas to be processed at low cost. Extruded monolithic honeycomb structures, such as those employed in the catalytic converters of automobiles, have excellent potential as structured contactors for CO2 adsorption applications because of the low pressure drop imposed on fluid moving through the straight channels of such structures. Here, we report the impregnation of poly(ethylenimine) (PEI), an effective aminopolymer reported commonly for CO2 separation, into extruded monolithic alumina to form structured CO2 sorbents. These structured sorbents are first prepared on a small scale, characterized thoroughly, and compared with powder sorbents with a similar composition. Despite consistent differences observed in the filling of mesopores with PEI between the monolithic and powder sorbents, their performance in CO2 adsorption is similar across a range of PEI contents. A larger monolithic cylinder (1 inch diameter, 4 inch length) is evaluated under conditions closer to those that might be used in large-scale applications and shows a similar performance to the smaller monoliths and powders tested initially. This larger structure is evaluated over five cycles of CO2 adsorption and steam desorption and demonstrates a volumetric capacity of 350 molCO2  m-3monolith and an equilibration time of 350 min under a 0.4 m s(-1) linear flow velocity through the monolith channels using 400 ppm CO2 in N2 as the adsorption gas at 30 °C. This volumetric capacity surpasses that of a similar technology considered previously, which suggested that CO2 could be removed from air at an operating cost as low as $100 per ton.

  16. Fabrication of 3D porous MoS{sub 2}-GO nanocomposite monolith as a promising adsorbent

    Energy Technology Data Exchange (ETDEWEB)

    Xia, Hongkun; Ji, Tianhao; Wu, You; Wu, Yongle [Beijing Technology and Business Univ., Beijing (China). College of Science

    2016-11-15

    Three-dimensional (3D) nanocomposite monolith containing MoS{sub 2} nanoflakes, graphene oxide (GO) and amorphous SiO{sub 2} was fabricated through a simple mixing process and hydrothermal treatment. Compared with GO monolith prepared under identical conditions, the MoS{sub 2}-GO monolith had larger specific surface area, smaller pore diameter, as well as much higher adsorption capacity for Cu{sup 2+} and Rhodamine B. Introducing amorphous SiO{sub 2} into the end monolith by using tetraethyl orthosilicate as a reactant in the synthesis reduced shrinkage and produced a greater number of large pores (>1 μm pore diameter) in the monolith. The specific surface area and pore diameter of the MoS{sub 2}-GO monolith were 321.4 m{sup 2} g{sup -1} and 11.71 nm, respectively. The higher adsorption capacity was ascribed to the presence of many S atoms in the MoS{sub 2} nanoflakes inside the monolith.

  17. Formulation of Aminosilica Adsorbents into 3D-Printed Monoliths and Evaluation of Their CO2 Capture Performance.

    Science.gov (United States)

    Thakkar, Harshul; Eastman, Stephen; Al-Mamoori, Ahmed; Hajari, Amit; Rownaghi, Ali A; Rezaei, Fateme

    2017-03-01

    Amine-based materials have represented themselves as a promising class of CO2 adsorbents; however, their large-scale implementation requires their formulation into suitable structures. In this study, we report formulation of aminosilica adsorbents into monolithic structures through a three-dimensional (3D) printing technique. In particular, 3D-printed monoliths were fabricated using presynthesized silica-supported tetraethylenepentamine (TEPA) and poly(ethylenimine) (PEI) adsorbents using three different approaches. In addition, a 3D-printed bare silica monolith was prepared and post-functionalized with 3-aminopropyltrimethoxysilane (APS). Characterization of the obtained monoliths indicated that aminosilica materials retained their characteristics after being extruded into 3D-printed configurations. Adsorptive performance of amine-based structured adsorbents was also investigated in CO2 capture. Our results indicated that aminosilica materials retain their structural, physical, and chemical properties in the monoliths. In addition, the aminosilica monoliths exhibited adsorptive characteristics comparable to their corresponding powders. This work highlights the importance of adsorbent materials formulations into practical contactors such as monoliths, as the scalabale technology platform, that could facilitate rapid deployment of adsorption-based CO2 capture processes on commercial scales.

  18. Water, mineral waters and health.

    Science.gov (United States)

    Petraccia, Luisa; Liberati, Giovanna; Masciullo, Stefano Giuseppe; Grassi, Marcello; Fraioli, Antonio

    2006-06-01

    The authors focus on water resources and the use of mineral waters in human nutrition, especially in the different stages of life, in physical activity and in the presence of some morbid conditions. Mineral water is characterized by its purity at source, its content in minerals, trace elements and other constituents, its conservation and its healing properties recognized by the Ministry of Health after clinical and pharmacological trials. Based on total salt content in grams after evaporation of 1l mineral water dried at 180 degrees C (dry residues), mineral waters can be classified as: waters with a very low mineral content, waters low in mineral content, waters with a medium mineral content, and strongly mineralized waters. Based on ion composition mineral waters can be classified as: bicarbonate waters, sulfate waters, sodium chloride or saltwater, sulfuric waters. Based on biological activity mineral waters can be classified as: diuretic waters, cathartic waters, waters with antiphlogistic properties. Instructions for use, doses, and current regulations are included.

  19. Preparation and characterization of poly-(methacrylatoethyl trimethylammonium chloride-co-vinylbenzyl chloride-co-ethylene dimethacrylate monolith

    Directory of Open Access Journals (Sweden)

    Eko Malis

    2015-05-01

    Full Text Available A polymer monolithic column, poly-(methacrylatoethyltrimethylammonium chloride-co-vinylbenzyl chloride-co-ethylene dimethacrylate or poly-(MATE-co-VBC-co-EDMA was successfully prepared in the current study by one-step thermally initiated in situ polymerization, confined in a steel tubing of 0.5 mm i.d. and 1/16” o.d. The monoliths were prepared from methacrylatoethyltrimethylammonium chloride (MATE and vinylbenzyl chloride (VBC as monomer and ethylene dimethacrylate (EDMA as crosslinker using a binary porogen system of 1-propanol and 1,4-butanediol. The inner wall of steel tubing was pretreated with 3-methacryloxypropyl-trimethoxysilane (MAPS. In order to obtain monolith with adequate column efficiency and low flow resistance, some parameters such as total monomer concentration (%T and crosslinker concentration (%C were optimized. The morphology of this monolith was assessed by scanning electron microscopy (SEM. The properties of the monolithic column, such as permeability, binding capacity, and pore size distribution were also characterized in detail. From the results of the characterization of all monolith variation, monolith with %T 30 %C 50 and %T 35 %C 50 give the best characteristic. These monoliths have high permeability, adequate molecular recognition sites (represented with binding capacity value of over 20 mg/mL, and have over 80% flow through pores in their pore structure contribute to low flow resistance. The resulted monolithic columns have promising potential for dual mode liquid chromatography. MATE may contribute for anion-exchange while VBC may responsible for reversed-phase liquid chromatography.

  20. Advances in the development of organic polymer monolithic columns and their applications in food analysis--a review.

    Science.gov (United States)

    Jandera, Pavel

    2013-10-25

    Monolithic continuous separation media are gradually finding their way to sample pre-treatment, isolation, enrichment and final analytical separations of a plethora of compounds, occurring as food components, additives or contaminants, including pharmaceuticals, pesticides and toxins, which have traditionally been the domain of particulate chromatographic materials. In the present review, recent advances in the technology of monolithic columns and the applications in food analysis are addressed. Silica-based monoliths are excellent substitutes to conventional particle-packed columns, improving the speed of analysis for low-molecular weight compounds, due to their excellent efficiency and high permeability. These properties have been recently appreciated in two-dimensional HPLC, where the performance in the second dimension is of crucial importance. Organic-polymer monoliths in various formats provide excellent separations of biopolymers. Thin monolithic disks or rod columns are widely employed in isolation, purification and pre-treatment of sample containing proteins, peptides or nucleic acid fragments. Monolithic capillaries were originally intended for use in electrochromatography, but are becoming more frequently used for capillary and micro-HPLC. Monoliths are ideal highly porous support media for immobilization or imprinting template molecules, to provide sorbents for shape-selective isolation of target molecules from various matrices occurring in food analysis. The separation efficiency of organic polymer monoliths for small molecules can be significantly improved by optimization of polymerization approach, or by post-polymerization modification. This will enable full utilization of a large variety of available monomers to prepare monoliths with chemistry matching the needs of selectivity of separations of various food samples containing even very polar or ionized compounds.