WorldWideScience

Sample records for monolayer modified ag

  1. A Solid Ag Film Deposited from Solution on Self-assembled Mercaptopropyltrimethoxysilane (MPTS) Monolayer

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Mercaptopropyltrimethoxysilane (MPTS) bearing mercapto groups was used to form self-assembly monolayers (SAMs) on glass substrates by solution extraction. SEM, XRD and rubbing test analysis illustrated that the Ag film on the SAMs-modified glass was more durable than that on the commonly-modified glass and that the crystallinity of Ag film on the SAMs-modified glass was identical with those of the Ag film on the commonly-modified glass and pure Ag.

  2. Monolayer solid of N-2/Ag(111)

    DEFF Research Database (Denmark)

    Bruch, L.W.; Hansen, Flemming Yssing

    1998-01-01

    An incommensurate monolayer solid of N-2/Ag(111) is modeled using extensive molecular-dynamics simulations. The conditions treated range from the low-temperature orientationally ordered solid to the melting of the solid. The properties are evaluated as a function of spreading pressure. Comparison...... is made to recent experimental data for N-2/Ag(111) and to results for N-2 adsorbed on graphite. Cu(110), and MgO(001). [S0163-1829(98)02715-5]....

  3. Quantitative determination of melamine in milk using Ag nanoparticle monolayer film as SERS substrate

    Science.gov (United States)

    Li, Ruoping; Yang, Jingliang; Han, Junhe; Liu, Junhui; Huang, Mingju

    2017-04-01

    A Raman method employing silver nanoparticle (Ag NP) monolayer film as Surface-enhanced Raman Scattering (SERS) substrate was presented to rapidly detect melamine in milk. The Ag NPs with 80 nm diameter were modified by polyvinylpyrrolidone to improve their uniformity and chemical stability. The treatment procedure of liquid milk required only addition of acetic acid and centrifugation, and required time is less than 15 min. The Ag NP monolayer film significantly enhanced Raman signal from melamine and allowed experimentally reproducible determination of the melamine concentration. A good linear relationship (R2=0.994) between the concentration and Raman peak intensity of melamine at 681 cm-1 was obtained for melamine concentrations between 0.10 mg L-1 and 5.00 mg L-1. This implies that this method can detect melamine concentrations below 1.0 mg L-1, the concentration currently considered unsafe.

  4. Cobalt monolayer islands on Ag(111) for ORR catalysis.

    Science.gov (United States)

    Loglio, Francesca; Lastraioli, Elisa; Bianchini, Claudio; Fontanesi, Claudio; Innocenti, Massimo; Lavacchi, Alessandro; Vizza, Francesco; Foresti, Maria Luisa

    2011-08-22

    The design of a catalyst for one of the most important electrocatalytic reactions, the oxygen reduction reaction (ORR), was done following the most recent guidelines of theoretical studies on this topic. Aim of this work was to achieve a synergic effect of two different metals acting on different steps of the ORR. The catalytic activity of Ag, already known and characterized, was enhanced by the presence of a monolayer of cobalt subdivided into nanosized islands. To obtain such a controlled nanostructure, a novel method utilizing self-assembled monolayers (SAMs) as templates was employed. In a recent study, we were able to perform a confined electrodeposition of cobalt onto Ag(111) in a template formed by selectively desorbing a short-chain thiol (3-mercaptopropionic acid, MPA) from binary SAMs using 1-dodecanthiols (DDT). This method allows for an excellent control of the morphology of the deposit by varying the molar ratio of the two thiols. Because cobalt does not deposit on silver at an underpotential, the alternative approach of surface limited redox replacement (SLRR) was used. This method, recently developed by Adžić et al., consists of the use of a monolayer of a third metal, which can be deposited at an underpotential, as a template for the spontaneous deposition of a more noble metal. Herein, we choose zinc as template for the deposition of cobalt. Ag(111) crystals were covered by monolayer islands consisting of cobalt, with the surface atomic ratios ranging from 12 to 39% for cobalt. The catalytic activity of such samples towards ORR was evaluated and the best improvement in activity was found to be that of the sample with a cobalt percentage of approximately 30% with respect to the bare silver, which is in good agreement with theoretical hypotheses.

  5. Highly conductive and transparent Ag honeycomb mesh fabricated using a monolayer of polystyrene spheres

    Science.gov (United States)

    Kwon, Namyong; Kim, Kyohyeok; Sung, Sihyun; Yi, Insook; Chung, Ilsub

    2013-06-01

    We describe the design principles and fabrication of Ag honeycomb mesh as a transparent conductive electrode using a polystyrene (PS) sphere template. Monolayers of PS spheres with different diameters, such as 600 nm, 3 μm, and 10 μm, are studied as templates to form Ag mesh with high transmittance. Since the parasitic Ag islands degrade the transmittance, both heat pretreatment and wet etching are used to control the area covered by parasitic Ag islands. The trade-off between transmittance and conductivity forces us to use larger diameter PS spheres. Ten-micron PS spheres are chosen as the template for the PS sphere monolayer, and heat pretreatment and Ag wet etching are used to demonstrate that the Ag honeycomb mesh transparent electrodes have high performance. The transmittance and the sheet resistance are 83% and 20 Ω/sq, which are comparable to commercial ITO electrodes.

  6. ELECTROCATALYSIS ON SURFACES MODIFIED BY METAL MONOLAYERS DEPOSITED AT UNDERPOTENTIALS.

    Energy Technology Data Exchange (ETDEWEB)

    ADZIC,R.

    2000-12-01

    The remarkable catalytic properties of electrode surfaces modified by monolayer amounts of metal adatoms obtained by underpotential deposition (UPD) have been the subject of a large number of studies during the last couple of decades. This interest stems from the possibility of implementing strictly surface modifications of electrocatalysts in an elegant, well-controlled way, and these bi-metallic surfaces can serve as models for the design of new catalysts. In addition, some of these systems may have potential for practical applications. The UPD of metals, which in general involves the deposition of up to a monolayer of metal on a foreign substrate at potentials positive to the reversible thermodynamic potential, facilitates this type of surface modification, which can be performed repeatedly by potential control. Recent studies of these surfaces and their catalytic properties by new in situ surface structure sensitive techniques have greatly improved the understanding of these systems.

  7. Superstrong encapsulated monolayer graphene by the modified anodic bonding.

    Science.gov (United States)

    Jung, Wonsuk; Yoon, Taeshik; Choi, Jongho; Kim, Soohyun; Kim, Yong Hyup; Kim, Taek-Soo; Han, Chang-Soo

    2014-01-07

    We report a superstrong adhesive of monolayer graphene by modified anodic bonding. In this bonding, graphene plays the role of a superstrong and ultra-thin adhesive between SiO2 and glass substrates. As a result, monolayer graphene presented a strong adhesion energy of 1.4 J m(-2) about 310% that of van der Waals bonding (0.45 J m(-2)) to SiO2 and glass substrates. This flexible solid state graphene adhesive can tremendously decrease the adhesive thickness from about several tens of μm to 0.34 nm for epoxy or glue at the desired bonding area. As plausible causes of this superstrong adhesion, we suggest conformal contact with the rough surface of substrates and generation of C-O chemical bonding between graphene and the substrate due to the bonding process, and characterized these properties using optical microscopy, atomic force microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy.

  8. Dipole Formation at Interfaces of Alkanethiolate Self-assembled Monolayers and Ag(111)

    NARCIS (Netherlands)

    Rusu, Paul C.; Giovannetti, Gianluca; Brocks, Geert

    2007-01-01

    The formation of interface dipoles in self-assembled monolayers (SAMs) of −CH3 and −CF3 terminated short-chain alkanethiolates on Ag(111) is studied by means of density functional theory calculations. The interface dipoles are characterized by monitoring the change in the surface work function upon

  9. Surface-enhanced Raman scattering-active gold nanoparticles modified with a monolayer of silver film.

    Science.gov (United States)

    Chang, Chun-Chao; Yang, Kuang-Hsuan; Liu, Yu-Chuan; Yu, Chung-Chin; Wu, Yi-Hao

    2012-11-07

    As shown in the literature, electrochemical underpotential deposition (UPD) offers the ability to deposit up to a monolayer of one metal onto a more noble metal with a flat surface. In this work, we develop an electrochemical pathway to prepare more surface-enhanced Raman scattering (SERS)-active substrates with Ag UPD-modified Au nanoparticles (NPs) by using sonoelectrochemical deposition-dissolution cycles (SEDDCs). Encouragingly, the SERS of Rhodamine 6G (R6G) adsorbed on these Ag UPD-modified Au NPs exhibits a higher intensity by ca. 12-fold magnitude, as compared with that of R6G adsorbed on unmodified Au NPs. The prepared SERS-active substrate demonstrates a large Raman scattering enhancement for R6G with a detection limit of 2 × 10(-14) M and an enhancement factor of 5.0 × 10(8). Also, the strategy proposed in this work to improve the SERS effects by using UPD Ag based on SEDDCs has an effect on the smaller probe molecules of 2,2'-bipyridine (BPy).

  10. Superstrong encapsulated monolayer graphene by the modified anodic bonding

    Science.gov (United States)

    Jung, Wonsuk; Yoon, Taeshik; Choi, Jongho; Kim, Soohyun; Kim, Yong Hyup; Kim, Taek-Soo; Han, Chang-Soo

    2013-12-01

    We report a superstrong adhesive of monolayer graphene by modified anodic bonding. In this bonding, graphene plays the role of a superstrong and ultra-thin adhesive between SiO2 and glass substrates. As a result, monolayer graphene presented a strong adhesion energy of 1.4 J m-2 about 310% that of van der Waals bonding (0.45 J m-2) to SiO2 and glass substrates. This flexible solid state graphene adhesive can tremendously decrease the adhesive thickness from about several tens of μm to 0.34 nm for epoxy or glue at the desired bonding area. As plausible causes of this superstrong adhesion, we suggest conformal contact with the rough surface of substrates and generation of C-O chemical bonding between graphene and the substrate due to the bonding process, and characterized these properties using optical microscopy, atomic force microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy.We report a superstrong adhesive of monolayer graphene by modified anodic bonding. In this bonding, graphene plays the role of a superstrong and ultra-thin adhesive between SiO2 and glass substrates. As a result, monolayer graphene presented a strong adhesion energy of 1.4 J m-2 about 310% that of van der Waals bonding (0.45 J m-2) to SiO2 and glass substrates. This flexible solid state graphene adhesive can tremendously decrease the adhesive thickness from about several tens of μm to 0.34 nm for epoxy or glue at the desired bonding area. As plausible causes of this superstrong adhesion, we suggest conformal contact with the rough surface of substrates and generation of C-O chemical bonding between graphene and the substrate due to the bonding process, and characterized these properties using optical microscopy, atomic force microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy. Electronic supplementary information (ESI) available. See DOI: 10.1039/c3nr03822j

  11. Optical absorption of (Ag-Au133(SCH352 bimetallic monolayer-protected clusters

    Directory of Open Access Journals (Sweden)

    Alessandro Fortunelli

    2016-10-01

    Full Text Available The evolution of the optical absorption spectrum of bimetallic Ag-Au monolayer-protected clusters (MPC obtained by progressively doping Ag into the experimentally known structure of Au133(SR52 was predicted via rigorous time-dependent density-functional theory (TDDFT calculations. In addition to monometallic Au133(SR52 and Ag133(SR52 species, 5 different (Ag-Au133(SR52 homotops were considered with varying Ag content and site positioning, and their electronic structure and optical response were analyzed in terms of Projected Density Of States (PDOS, the induced or transition electron density, and Transition Component Maps (TCM at selected excitation energies. It was found that Ag doping led to the effects rather different from those encountered in bare metal clusters. And it was also observed that Ag doping could produce structured spectral features, especially in the 3–4 eV range but also in the optical region if Ag atoms were located in the sub-staple region, as rationalized by the accompanying electronic analysis. Additionally, Au doping into the staples of Ag-rich MPC also gave rise to a more homogeneous induced electron density. These findings show the great sensitivity of the electronic response of MPC nanoalloy systems to the exact location of the alloying sites.

  12. Underpotential deposition of thallium, lead, and cadmium at silver electrodes modified with self-assembled monolayers of (3-mercaptopropyl)trimethoxysilane.

    Science.gov (United States)

    Robertson, Joseph W F; Tiani, Domenic J; Pemberton, Jeanne E

    2007-04-10

    Investigation of the underpotential deposition (UPD) of three metals-Tl, Pb, and Cd-on Ag surfaces modified with self-assembled monolayers (SAMs) of (3-mercaptopropyl)trimethoxysilane (3MPT) is reported. On the basis of the observation of negative potential shifts for their UPD processes, Tl and Pb undergo UPD directly on the underlying Ag surface by insertion between the Ag-S bond. This process is proposed to occur by penetration of the 3MPT monolayer by hydrated metal ions through spaces in six-membered siloxane rings that form at the terminus of the 3MPT layer after hydrolysis and condensation. In contrast, Cd does not undergo similarly facile UPD at 3MPT-modified Ag electrodes due to a hydrated ion size too large to fit through these openings. The voltammetric evidence that suggests that the hydrated metal cation size, as described by the Stokes diameter, is the primary determinant of Ag electrode accessibility for UPD through the cross-linked 3MPT layer is further supported by molecular mechanics energy minimization computations of six-membered siloxane rings on each of the three low-index faces of Ag. Finally, the 3MPT monolayer is shown to be exceptionally stable to repeated UPD/stripping cycles of Tl and Pb in contrast to SAMs of similar thickness formed from normal alkanethiols.

  13. Adsorption behavior of Fe atoms on a naphthalocyanine monolayer on Ag(111) surface

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Linghao; Wu, Rongting; Bao, Deliang; Ren, Junhai; Zhang, Yanfang; Zhang, Haigang; Huang, Li; Wang, Yeliang; Du, Shixuan; Huan, Qing; Gao, Hong-Jun

    2015-05-29

    Adsorption behavior of Fe atoms on a metal-free naphthalocyanine (H2Nc) monolayer on Ag(111) surface at room temperature has been investigated using scanning tunneling microscopy combined with density functional theory (DFT) based calculations. We found that the Fe atoms adsorbed at the centers of H2Nc molecules and formed Fe-H2Nc complexes at low coverage. DFT calculations show that the configuration of Fe at the center of a molecule is the most stable site, in good agreement with the experimental observations. After an Fe-H2Nc complex monolayer was formed, the extra Fe atoms self-assembled to Fe clusters of uniform size and adsorbed dispersively at the interstitial positions of Fe-H2Nc complex monolayer. Furthermore, the H2Nc monolayer grown on Ag(111) could be a good template to grow dispersed magnetic metal atoms and clusters at room temperature for further investigation of their magnetism-related properties.

  14. Incorporated Organic Modified Ag Nanoparticles in Ormocer

    Institute of Scientific and Technical Information of China (English)

    Haiping XIA; Jianli ZHANG; Jinhao WANG; Qiuhua NIE

    2004-01-01

    Ag nanoparticles coated trisodium citrate were incorporated in ormocer by sol-gel method. The doping concentration of Ag in ormocer is about 1.0% in weight. The HRTFM demonstrated that the particles disperse in ormocer, and the size of Ag nanoparticles is 5~10 nm. The absorption band of Ag nanoparticle at 410 nm was observed.

  15. Density Functional Theory with Modified Dispersion Correction for Metals Applied to Self-Assembled Monolayers of Thiols on Au(111

    Directory of Open Access Journals (Sweden)

    M. P. Andersson

    2013-01-01

    Full Text Available Using sound physical principles we modify the DFT-D2 atom pairwise semiempirical dispersion correction to density functional theory to work for metallic systems and in particular self-assembled monolayers of thiols on gold surfaces. We test our approximation for two functionals PBE-D and revPBE-D for lattice parameters and cohesive energies for Ni, Pd, Pt, Cu, Ag, and Au, adsorption energies of CO on (111 surfaces of Pd, Pt, Cu, Ag, and Au, and adsorption energy of benzene on Ag(111 and Au(111. Agreement with experimental data is substantially improved. We apply the method to self-assembled monolayers of alkanethiols on Au(111 and find reasonable agreement for PBE-D and revPBE-D for both physisorption of n-alkanethiols as well as dissociative chemisorption of dimethyl disulfide as an Au-adatom-dithiolate complex. By modifying the C6 coefficient for Au, we obtain quantitative agreement for physisorption and chemisorption for both PBE-D and revPBE-D using the same set of parameters. Our results confirm that inclusion of dispersion forces is crucial for any quantitative analysis of the thiol and thiolate bonds to the gold surface using quantum chemical calculations.

  16. From monomer to monolayer: a global optimisation study of (ZnO)n nanoclusters on the Ag surface.

    Science.gov (United States)

    Demiroglu, Ilker; Woodley, Scott M; Sokol, Alexey A; Bromley, Stefan T

    2014-12-21

    We employ global optimisation to investigate how oxide nanoclusters of increasing size can best adapt their structure to lower the system energy when interacting with a realistic extended metal support. Specifically, we focus on the (ZnO)@Ag(111) system where experiment has shown that the infinite Ag(111)-supported ZnO monolayer limit corresponds to an epitaxially 7 : 8 matched graphene-like (Zn(3)O(3))-based hexagonal sheet. Using a two-stage search method based on classical interatomic potentials and then on more accurate density functional theory, we report global minina candidate structures for Ag-supported (ZnO)n cluster with sizes ranging from n = 1-24. Comparison with the respective global minina structure of free space (ZnO)n clusters reveals that the surface interaction plays a decisive role in determining the lowest energy Ag-supported (ZnO)n cluster structures. Whereas free space (ZnO)n clusters tend to adopt cage-like bubble structures as they grow larger, Ag-supported (ZnO)n clusters of increasing size become progressively more like planar cuts from the infinite graphene-like ZnO single monolayer. This energetic favourability for planar hexagonal Ag-supported clusters over their 3D counterparts can be partly rationalised by the ZnO-Ag(111) epitaxial matching and the increased number of close interactions with the Ag surface. Detailed analysis shows that this tendency can also be attributed to the capacity of 2D clusters to distort to improve their interaction with the Ag surface relative to more rigid 3D bubble cluster isomers. For the larger sized clusters we find that the adsorption energies and most stable structural types appear to be rather converged confirming that our study makes a bridge between the Ag-supported ZnO monomer and the infinite Ag-supported ZnO monolayer.

  17. Characteristics of localized surface plasmons excited on mixed monolayers composed of self-assembled Ag and Au nanoparticles.

    Science.gov (United States)

    Tanaka, Daisuke; Imazu, Keisuke; Sung, Jinwoo; Park, Cheolmin; Okamoto, Koichi; Tamada, Kaoru

    2015-10-07

    The fundamental characteristics of localized surface plasmon resonance (LSPR) excited on mixed monolayers composed of self-assembled Ag and Au nanoparticles (AgNPs and AuNPs, respectively) were investigated. Mixed monolayered films were fabricated at the air-water interface at different mixing ratios. The films retained their phase-segregated morphologies in which AuNPs formed several 10 to 100 nm island domains in a homogeneous AgNP matrix phase. The LSPR bands originating from the self-assembled domains shifted to longer wavelengths as the domain size increased, as predicted by a finite-difference time-domain (FDTD) simulation. The FDTD simulation also revealed that even an alternating-lattice-structured two-dimensional (2D) AgNP/AuNP film retained two isolated LSPR bands, revealing that the plasmon resonances excited on each particle did not couple even in a continuous 2D sheet, unlike in the homologous NP system. The fluorescence quenching test of Cy3 and Cy5 dyes confirmed that the independent functions of AuNPs and AgNPs remained in the mixed films, whereas the AuNPs exhibited significantly higher quenching efficiency for the Cy3 dye compared with AgNPs due to the overlap of the excitation/emission bands of the dyes with the AuNP LSPR band. Various applications can be considered using this nanoheterostructured plasmonic assembly to excite spatially designed, high-density LSPR on macroscopic surfaces.

  18. The protonation state of thiols in self-assembled monolayers on roughened Ag/Au surfaces and nanoparticles.

    Science.gov (United States)

    Bandyopadhyay, Sabyasachi; Chattopadhyay, Samir; Dey, Abhishek

    2015-10-14

    The protonation state of thiols in self-assembled monolayers (SAMs) on Ag and Au surfaces and nanoparticles (NPs) has been an issue of contestation. It has been recently demonstrated that deuterating the thiol proton produces ostentatious changes in the Raman spectra of thiols and can be used to detect the presence of the thiol functional group. Surface enhanced Raman spectroscopy (SERS) of H/D substituted aliphatic thiols on Ag surfaces clearly shows the presence of S-H vibration between 2150-2200 cm(-1) which shifts by 400 cm(-1) upon deuteration and a simultaneous >20 cm(-1) shift in the C-S vibration of thiol deuteration. Large shifts (>15 cm(-1)) in the C-S vibration are also observed for alkyl thiol SAMs on Au surfaces. Alternatively, neither the S-H vibration nor the H/D isotope effect on the C-S vibration is observed for alkyl thiol SAMs on Ag/Au NPs. XPS data on Ag/Au surfaces bearing aliphatic thiol SAMs show the presence of both protonated and deprotonated thiols while on Ag/Au NPs only deprotonated thiols are detected. These data suggest that aliphatic thiol SAMs on Au/Ag surfaces are partially protonated whereas they are totally deprotonated on Au/Ag NPs. Aromatic PhSH SAMs on Ag/Au surfaces and Ag/Au NPs do not show these vibrations or H/D shifts as well indicating that the thiols are deprotonated at these interfaces.

  19. Overpotential deposition of Ag monolayer and bilayer on Au(1 1 1) mediated by Pb adlayer underpotential deposition/stripping cycles

    Science.gov (United States)

    Wang, J. X.; Ocko, B. M.; Adzic, R. R.

    2003-08-01

    Ultra-thin Ag films on the Au(1 1 1) surface were prepared via overpotential deposition (OPD) in the presence of Pb 2+ ions. By carrying out repetitive Pb adlayer underpotential deposition (UPD) and stripping cycles during Ag bulk deposition, the two-dimensional growth of Ag films was significantly enhanced in high OPD. The Ag monolayer sample was made by comparing the voltammetry curves, in which the signatures for Pb adlayer UPD on Au(1 1 1) changed to that on Ag(1 1 1). As demonstrated by the X-ray specular reflectivity measurements, nearly complete monolayer and bilayer films can be made with optimized deposition procedures. On subatomic scale, however, we found that these films have significant higher root-mean-square displacement amplitudes than those underpotentially deposited Ag monolayer and bilayer on either Au(1 1 1) or Pt(1 1 1).

  20. Catalytic monolayer voltammetry and in situ scanning tunneling microscopy of copper nitrite reductase on cysteamine-modified Au(111) electrodes

    DEFF Research Database (Denmark)

    Zhang, Jingdong; Welinder, A.C.; Hansen, Allan Glargaard

    2003-01-01

    We have studied the adsorption and electrocatalysis of the redox metalloenzyme blue copper nitrite reductase from Achromobacter xylosoxidans (AxCuNiR) on single-crystal Au(111)-electrode surfaces modified by a self-assembled monolayer of cysteamine. A combination of cyclic voltammetry and in situ...... biotechnology at the monolayer and toward the single-molecule level....

  1. Development of a DNA Sensor Based on Alkanethiol Self- Assembled Monolayer-Modified Electrodes

    Directory of Open Access Journals (Sweden)

    José M. Pingarrón

    2005-11-01

    Full Text Available An electrochemical DNA biosensor based on recognition of double or singlestranded DNA (ds-DNA/ss-DNA immobilised on a self-assembled modified gold electrodeis presented for denaturalisation and hybridisation detection. DNA is covalently bond on aself assembled 3-mercaptopropionic acid monolayer by using water soluble N-3-(dimethylaminopropyl-N´ethylcarbodiimide hydrochloride (EDC and Nhydroxisulfosuccinimide(NHSS as linkers. The interaction between the immobilised DNAand methylene blue (MB is investigated using square wave voltammetry (SWV. Theincrease or diminution of peak currents of the MB upon the hybridisation or denaturalisationevent at the modified electrode surface is studied.

  2. Growth and ordering of Ni(II) diphenylporphyrin monolayers on Ag(111) and Ag/Si(111) studied by STM and LEED.

    Science.gov (United States)

    Murphy, B E; Krasnikov, S A; Cafolla, A A; Sergeeva, N N; Vinogradov, N A; Beggan, J P; Lübben, O; Senge, M O; Shvets, I V

    2012-02-01

    The room temperature self-assembly and ordering of (5,15-diphenylporphyrinato)nickel(II) (NiDPP) on the Ag(111) and Ag/Si(111)-(√3 × √3)R30° surfaces have been investigated using scanning tunnelling microscopy and low-energy electron diffraction. The self-assembled structures and lattice parameters of the NiDPP monolayer are shown to be extremely dependent on the reactivity of the substrate, and probable molecular binding sites are proposed. The NiDPP overlayer on Ag(111) grows from the substrate step edges, which results in a single-domain structure. This close-packed structure has an oblique unit cell and consists of molecular rows. The molecules in adjacent rows are rotated by approximately 17° with respect to each other. In turn, the NiDPP molecules form three equivalent domains on the Ag/Si(111)-(√3 × √3)R30° surface, which follow the three-fold symmetry of the substrate. The molecules adopt one of three equivalent orientations on the surface, acting as nucleation sites for these domains, due to the stronger molecule-substrate interaction compared to the case of the Ag(111). The results are explained in terms of the substrate reactivity and the lattice mismatch between the substrate and the molecular overlayer.

  3. Electrochemical immobilization of biomolecules on gold surface modified with monolayered L-cysteine

    Energy Technology Data Exchange (ETDEWEB)

    Honda, Mitsunori, E-mail: honda.mitsunori@jaea.go.jp; Baba, Yuji; Sekiguchi, Tetsuhiro; Shimoyama, Iwao; Hirao, Norie

    2014-04-01

    Immobilization of organic molecules on the top of a metal surface is not easy because of lattice mismatch between organic and metal crystals. Gold atoms bind to thiol groups through strong chemical bonds, and a self-assembled monolayer of sulfur-terminated organic molecules is formed on the gold surface. Herein, we suggested that a monolayer of L-cysteine deposited on a gold surface can act as a buffer layer to immobilize biomolecules on the metal surface. We selected lactic acid as the immobilized biomolecule because it is one of the simplest carboxyl-containing biomolecules. The immobilization of lactic acid on the metal surface was carried out by an electrochemical method in an aqueous environment under the potential range varying from − 0.6 to + 0.8 V. The surface chemical states before and after the electrochemical reaction were characterized using X-ray photoelectron spectroscopy (XPS). The N 1s and C 1s XPS spectra showed that the L-cysteine-modified gold surface can immobilize lactic acid via peptide bonds. This technique might enable the immobilization of large organic molecules and biomolecules. - Highlights: • Monolayer l-cysteine deposited on Au surface as a buffer layer to immobilize biomolecules. • Lactic acid as the immobilized biomolecule as it is simple carboxyl-containing biomolecule. • X-ray photoelectron spectroscopy (XPS) of surface chemical states, before and after. • L-cysteine-modified Au surface can immobilize lactic acid via peptide bonds.

  4. Dual-loss-modulated Q-switched Tm:LuAG laser with AOM and monolayer graphene.

    Science.gov (United States)

    Luan, Chao; Yang, Ke Jian; Zhao, Jia; Zhao, Sheng Zhi; Qiao, Wen Chao; Li, Tao; Feng, Tian Li; Liu, Cheng; Qiao, Jun Peng; Zheng, Li He; Xu, Jun; Wang, Qing Guo; Su, Liang Bi

    2015-09-20

    A laser-diode-pumped dual-loss-modulated Q-switching Tm:LuAG laser with an acousto-optic modulator (AOM) and monolayer graphene saturable absorber (SA) around 2 μm is presented for the first time to the best of our knowledge. The average output power and the pulse widths for different repetition rates have been measured. In comparison with the singly Q-switching laser with AOM or with monolayer graphene SA, the dual-loss-modulated Q-switching laser could generate shorter pulse width and higher peak power. The maximum pulse width compression ratio was found to be 3.11, and the highest peak power was enhanced 97.4 times. The experimental results show that the dual-loss-modulated technology is an efficient method for compressing the pulse width, improving the peak power, and enhancing the pulse stability for the Q-switched lasers at 2 μm.

  5. Comparative study of electroless copper film on different self-assembled monolayers modified ABS substrate.

    Science.gov (United States)

    Xu, Jiushuai; Fan, Ruibin; Wang, Jiaolong; Jia, Mengke; Xiong, Xuanrui; Wang, Fang

    2014-04-15

    Copper films were grown on (3-Mercaptopropyl)trimethoxysilane (MPTMS), (3-Aminopropyl)triethoxysilane (APTES) and 6-(3-(triethoxysilyl)propylamino)-1,3,5- triazine-2,4-dithiol monosodium (TES) self-assembled monolayers (SAMs) modified acrylonitrile-butadiene-styrene (ABS) substrate via electroless copper plating. The copper films were examined using scanning electron microscopy (SEM) and X-ray diffraction (XRD). Their individual deposition rate and contact angle were also investigated to compare the properties of SAMs and electroless copper films. The results indicated that the formation of copper nuclei on the TES-SAMs modified ABS substrate was faster than those on the MPTMS-SAMs and APTES-SAMs modified ABS substrate. SEM images revealed that the copper film on TES-SAM modified ABS substrate was smooth and uniform, and the density of copper nuclei was much higher. Compared with that of TES-SAMs modified resin, the coverage of copper nuclei on MPTMS and APTES modified ABS substrate was very limited and the copper particle size was too big. The adhesion property test demonstrated that all the SAMs enhanced the interfacial interaction between copper plating and ABS substrate. XRD analysis showed that the copper film deposited on SAM-modified ABS substrate had a structure with Cu(111) preferred orientation, and the copper film deposited on TES-SAMs modified ABS substrate is better than that deposited on MPTMS-SAMs or APTES-SAMs modified ABS resins in electromigrtion resistance.

  6. Comparative Study of Electroless Copper Film on Different Self-Assembled Monolayers Modified ABS Substrate

    Directory of Open Access Journals (Sweden)

    Jiushuai Xu

    2014-04-01

    Full Text Available Copper films were grown on (3-Mercaptopropyltrimethoxysilane (MPTMS, (3-Aminopropyltriethoxysilane (APTES and 6-(3-(triethoxysilylpropylamino-1,3,5- triazine-2,4-dithiol monosodium (TES self-assembled monolayers (SAMs modified acrylonitrile-butadiene-styrene (ABS substrate via electroless copper plating. The copper films were examined using scanning electron microscopy (SEM and X-ray diffraction (XRD. Their individual deposition rate and contact angle were also investigated to compare the properties of SAMs and electroless copper films. The results indicated that the formation of copper nuclei on the TES-SAMs modified ABS substrate was faster than those on the MPTMS-SAMs and APTES-SAMs modified ABS substrate. SEM images revealed that the copper film on TES-SAM modified ABS substrate was smooth and uniform, and the density of copper nuclei was much higher. Compared with that of TES-SAMs modified resin, the coverage of copper nuclei on MPTMS and APTES modified ABS substrate was very limited and the copper particle size was too big. The adhesion property test demonstrated that all the SAMs enhanced the interfacial interaction between copper plating and ABS substrate. XRD analysis showed that the copper film deposited on SAM-modified ABS substrate had a structure with Cu(111 preferred orientation, and the copper film deposited on TES-SAMs modified ABS substrate is better than that deposited on MPTMS-SAMs or APTES-SAMs modified ABS resins in electromigrtion resistance.

  7. CHEMICALLY MODIFIED FIELD-EFFECT TRANSISTORS - POTENTIOMETRIC AG+ SELECTIVITY OF PVC MEMBRANES BASED ON MACROCYCLIC THIOETHERS

    NARCIS (Netherlands)

    BRZOZKA, Z; COBBEN, PLHM; REINHOUDT, DN; EDEMA, JJH; KELLOGG, RM

    1993-01-01

    A chemically modified field-effect transistor (CHEMFET) with satisfactory Ag+ selectivity is described. The potentiometric Ag+ selectivities of CHEMFETs with plasticized PVC membranes based on macrocyclic thioethers have been determined. All the macrocyclic thioethers tested showed silver response a

  8. Electroanalysis of dopamine at a gold electrode modified with N-acetylcysteine self-assembled monolayer.

    Science.gov (United States)

    Liu, Ting; Li, Meixian; Li, Qianyuan

    2004-07-01

    Voltammetric behavior of dopamine (DA) on a gold electrode modified with the self-assembled monolayer (SAM) of N-acetylcysteine has been investigated, and one pair of well-defined redox peaks of dopamine is obtained at the SAM modified gold electrode. The oxidation peak current increases linearly with the concentration of dopamine in the range of 1.0x10 (-6)to 2.0x10 (-4)moll(-1). The detection limit is 8.0x10(-7)moll(-1). This method will be applicable to the determination of dopamine in injection of dopamine hydrochloride, and the good recovery of dopamine is obtained. Furthermore, The SAM modified gold electrode can resolve well the voltammetric responses of dopamine and ascorbic acid (AA), so it can also be applied to the determination of dopamine in the presence of ascorbic acid.

  9. Ammonia synthesis on Au modified Fe(111) and Ag and Cu modified Fe(100) surfaces

    DEFF Research Database (Denmark)

    Lytken, Ole; Waltenburg, Hanne Neergaard; Chorkendorff, Ib

    2003-01-01

    In order to investigate any influence of steps and possible positive effects of making surface alloys the ammonia synthesis has been investigated over Au modified Fe(111) and Ag and Cu modified Fe(100) single crystals in the temperature range 603-773 K, using a system combining ultra-high vacuum...... and a high-pressure cell. Ammonia was synthesized from a stoichiometric (N-2:3H(2)) gas mixture at a pressure of 2 bar. By deposition of small amounts of An, the ammonia production activity of the Fe(1 1 1) surface can be enhanced. More important, for the gold modified surface, the reaction order in ammonia...

  10. Adsorption geometry and electronic properties of flat-lying monolayers of tetracene on the Ag(111) surface

    Science.gov (United States)

    Zaitsev, N. L.; Nechaev, I. A.; Höfer, U.; Chulkov, E. V.

    2016-10-01

    The geometrical and electronic properties of the monolayer (ML) of tetracene (Tc) molecules on Ag(111) are systematically investigated by means of DFT calculations with the use of a localized basis set. The bridge and hollow adsorption positions of the molecule in the commensurate γ -Tc/Ag(111) are revealed to be the most stable and equally favorable irrespective to the approximation chosen for the exchange-correlation functional. The binding energy is entirely determined by the long-range dispersive interaction. The former lowest unoccupied molecular orbital remains being unoccupied in the case of γ -Tc/Ag(111) as well as in the α phase with increased coverage. The unit cell of the α phase with point-on-line registry was adapted for calculations based on the available experimental data and computed structures of the γ phase. The calculated position of the Tc/Ag(111) interface state is found to be noticeably dependent on the lattice constant of the substrate, however its energy shift with respect to the Shockley surface state of the unperturbed clean side of the slab is sensitive only to the adsorption distance and in good agreement with the experimentally measured energy shift.

  11. Dual functions of 2D WS2 and MoS2-WS2 monolayers coupled with a Ag3PO4 photocatalyst

    Science.gov (United States)

    Wei, Zeng-Xi; Huang, Wei-Qing; Xu, Liang; Hu, Wangyu; Peng, P.; Huang, Gui-Fang

    2016-09-01

    The photocatalytic performance of semiconductors can be improved by coupling two-dimensional (2D) layered materials. Understanding the underlying mechanism of this phenomenon at the electronic level is important for the development of photocatalysts with a high efficiency. Here, we first present a theoretical elucidation of the dual functions of 2D layered material as a sensitizer and a co-catalyst by performing density functional theory calculations, taking WS2 and a lateral heterogeneous WS2-MoS2 monolayer as examples to couple with a promising photocatalyst Ag3PO4. The band alignment of a staggered type-II is formed between Ag3PO4 and the 2D monolayer with the latter possessing the higher electron affinity, resulting in the robust separation of photoexcited charge carriers between them, and indicating that the 2D monolayer is an effective sensitizer. Interestingly, the W (Mo) atoms, which are catalytically inert in the isolated 2D monolayer, turn into catalytic active sites, making the 2D monolayer a highly active co-catalyst in hybrids. A better photocatalytic performance in the coupled lateral heterogeneous WS2-MoS2 monolayer and Ag3PO4 can be expected. The calculated results can be rationalized by available experiments. These findings provide theoretical evidence supporting the experimental reports and may be used as a foundation for developing highly efficient 2D layered materials-based photocatalysts.

  12. Electrical resistivity of nanoporous gold modified with thiol self-assembled monolayers

    Science.gov (United States)

    Hakamada, Masataka; Kato, Naoki; Mabuchi, Mamoru

    2016-11-01

    The electrical resistivity of nanoporous gold (NPG) modified with thiol self-assembled monolayers (SAMs) has been measured at 298 K using a four-probe method. We found that the adsorption of thiol SAMs increases the electrical resistivity of NPG by up to 22.2%. Dependence of the electrical resistivity on the atmosphere (air or water) was also observed in SAMs-modified NPG, suggesting that the electronic states of the tail groups affect the electrons of the binding sulfur and adjacent surface gold atoms. The present results suggest that adsorption of thiol molecules can influence the behavior of the conducting electrons in NPG and that modification of NPG with SAMs may be useful for environmental sensing.

  13. Anion Adsorption on an Au Colloid Monolayer Based Cysteamine-Modified Gold Electrode

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Anion adsorption behavior on Au colloid surface was investigated in virture of depositing monolayers of Au colloid on the self-assembled monolayers of cysteamine on a gold electrode. Po tential-dependent anion adsorption-desorption waves via the nonfaradaic current were obtained by means of cyclic voltammetry at Au colloid-modified gold electrodes in the potential range of -200-600 mV. The adsorption sequence in the order of adsorption peak potentials(Epa) is OH->citrate3->H2PO4->Cl->SO42->ClO4->NO3-. Among them, citrate3-exhibited an en tirely irreversible adsorption. A rise in temperature can increase the rates of adsorption-desorp tion and improve the reversibility of the adsorption-desorption of CI-, SO24-, CIO4-, NO3- and H2PO4-. The adsorption peak potentials shifted more negatively for ca. 63 mV as the anion con centrations were increased by a decade factor. The change of pH from 7 to 1 slightly affected the adsorption peak potentials of Cl- and NO3-. Au colloids with a smaller size (16 nm) gave rise to a better reversibility of the adsorption-desorption process and lower adsorption currents. The ex perimental results of citrate ions adsorption on Au colloid surface show that Au colloids with a smaller size prepared by sodium citrate method exhibited a higher stability in the solution in com parison to those with larger sizes because of its higher ratio of charge/mass. In other words, the smaller gold nanoparticles are covered with citrate ions monolayer that can also be formed at larg er gold nanoparticles by means of electrochemical scan.

  14. Conformational morphology of polyaniline grown on self-assembled monolayer modified silicon

    Energy Technology Data Exchange (ETDEWEB)

    Sutar, D.S., E-mail: dssutar23@gmail.com [Central Surface Analytical Facility, Indian Institute of Technology Bombay, Mumbai 400076 (India); Department of Physics, Indian Institute of Technology Bombay, Mumbai 400076 (India); Major, S.S. [Department of Physics, Indian Institute of Technology Bombay, Mumbai 400076 (India); Srinivasa, R.S. [Department of Metallurgical Engineering and Materials Science, Indian Institute of Technology Bombay, Mumbai 400076 (India); Yakhmi, J.V. [Technical Physics Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)

    2011-10-31

    Polyaniline (PANI) films with pyramidal shaped crystallites were prepared by self-organization on self-assembled monolayer (SAM) modified Si substrates. High-resolution atomic force microscopy (HR-AFM) shows that SAM has tridymite structural order and the PANI film has biphasic conformational morphology corresponding to face-on orientation and edge-on orientation. Order parameters obtained from power spectral density analysis of HR-AFM images of SAM and PANI films show that the pyramidal crystallites are in emeraldine salt (ES-I) form and the region between the crystallites is in emeraldine base (EB-II) form. The ordered lattice of PANI crystallites as observed by cross-sectional HR-TEM confirms its single crystalline nature as well as epitaxial growth. The heteroepitaxial growth of PANI is attributed to the structural order of interfacial SAM on Si. - Highlights: > The structural order of self-assembled monolayer (SAM) on Si assists in hetero-epitaxial growth of polyaniline (PANI) films. > The power spectral density (PSD) analysis of the high-resolution AFM images provides the order parameters, which help to elucidate the ordering in SAM and PANI films. > PSD function could be used to analyze the high-resolution AFM images, which hitherto has been used mainly for low-resolution image analysis. > The ordered lattice image and SAED pattern obtained by HR-TEM confirms the single crystalline nature of pyramidal crystallites and their epitaxial growth at the interface.

  15. Electrochemical studies of cystine modified self-assembled monolayer for Escherichia coli detection

    Energy Technology Data Exchange (ETDEWEB)

    Pandey, Chandra Mouli; Sumana, Gajjala [Department of Science and Technology Centre on Biomolecular Electronics, Biomedical Instrumentation Section, Materials Physics and Engineering Division, National Physical Laboratory (Council of Scientific and Industrial Research), Dr. K. S. Krishnan Marg, New Delhi 110012 (India); Sood, K.N. [Electron Microscope Section, Division of Material Characterization, National Physical Laboratory, Dr. K. S. Krishnan Marg, New Delhi 110012 (India); Malhotra, B.D., E-mail: bansi.malhotra@gmail.co [Department of Science and Technology Centre on Biomolecular Electronics, Biomedical Instrumentation Section, Materials Physics and Engineering Division, National Physical Laboratory (Council of Scientific and Industrial Research), Dr. K. S. Krishnan Marg, New Delhi 110012 (India)

    2010-11-30

    An electrochemical DNA biosensor based on cystine modified self-assembled monolayer (cys-SAM) onto gold electrode (AuE) has been fabricated for Escherichia coli (E. coli) detection. This biosensing electrode has been characterized using scanning electron microscopy (SEM), FT-IR spectroscopy, cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS). Under the optimum conditions, this DNA biosensor can be used to detect complementary target DNA concentration in the range of 1 x 10{sup -6} M to 1 x 10{sup -20} M within 60 s of hybridization time at 25 {sup o}C and has been found to be stable for about four months when stored at 4 {sup o}C.

  16. Enhancement of broad-band light absorption in monolayer MoS2 using Ag grating hybrid with distributed Bragg reflector

    Science.gov (United States)

    Cao, Jintao; Wang, Jin; Yang, Guofeng; Lu, Yann; Sun, Rui; Yan, Pengfei; Gao, Shumei

    2017-10-01

    A hybrid novel structure of monolayer MoS2 with Ag nanograting and DBR on Si substrate has been proposed to obtain broad-band absorption response for two-dimensional (2D) materials. It is effective to reduce light loss and reflect the incident light efficiently for monolayer MoS2 absorption with DBR dielectric layers. Moreover, by combining Ag nanograting with DBR structure, the average absorption achieves as high as 59% within broad wavelength ranging from 420 to 700 nm, which is attributed to the plasmonic resonant effect of metal nanostripes. The absorption would be affected by the duty ratio and period of the Ag nanograting, and shows incident angle dependent characteristics, while an average absorption higher than 60% has been obtained at the incident angle around 40°. These results indicate that 2D MoS2 in combination with DBR and metal nanograting have a promising potential applications for optical nano-devices.

  17. Gold Electrodes Modified with Self-Assembled Monolayers for Measuring L-Ascorbic Acid: An Undergraduate Analytical Chemistry Laboratory Experiment

    Science.gov (United States)

    Ito, Takashi; Perera, D. M. Neluni T.; Nagasaka, Shinobu

    2008-01-01

    This article describes an undergraduate electrochemistry laboratory experiment in which the students measure the L-ascorbic acid content of a real sample. Gold electrodes modified with self-assembled monolayers (SAMs) of thioctic acid and cysteamine are prepared to study the effects of surface modification on the electrode reaction of L-ascorbic…

  18. Catalytic monolayer voltammetry and in situ scanning tunneling microscopy of copper nitrite reductase on cysteamine-modified Au(111) electrodes

    DEFF Research Database (Denmark)

    Zhang, Jingdong; Welinder, A.C.; Hansen, Allan Glargaard

    2003-01-01

    We have studied the adsorption and electrocatalysis of the redox metalloenzyme blue copper nitrite reductase from Achromobacter xylosoxidans (AxCuNiR) on single-crystal Au(111)-electrode surfaces modified by a self-assembled monolayer of cysteamine. A combination of cyclic voltammetry and in situ...

  19. Enhancing photocatalytic activity for hydrogen production and pollutant degradation by modifying tetragonal ZrO2 with monolayers slab surface of BiVO4, Ag3PO4, SrTiO3 and WO3: A first-principles study

    CSIR Research Space (South Africa)

    Opoku, F

    2017-10-01

    Full Text Available Semiconductor-based photocatalysis has received increasing attention in energy storage and environmental remediation process due to the abundant solar energy. For this purpose, heterostructures of ZrO2 coupled with BiVO4, Ag3PO4, SrTiO3 and WO3...

  20. Highly sensitive and selective electrochemical determination of dopamine and ascorbic acid at Ag/Ag{sub 2}S modified electrode

    Energy Technology Data Exchange (ETDEWEB)

    Li, Chen-Yan [Department of Chemical Engineering, National Cheng Kung University, Tainan 70101, Taiwan (China); Advanced Optoelectronic Technology Center, National Cheng Kung University, Tainan 70101, Taiwan (China); Cai, Ying-Jie [Department of Chemical Engineering, National Cheng Kung University, Tainan 70101, Taiwan (China); Yang, Chien-Hsin [Department of Chemical and Materials Engineering, National University of Kaohsiung, Kaohsiung 81148, Taiwan (China); Wu, Chen-Hao [Department of Chemical Engineering, National Cheng Kung University, Tainan 70101, Taiwan (China); Wei, Yen [Department of Chemical Engineering, National Cheng Kung University, Tainan 70101, Taiwan (China); Department of Chemistry, Drexel University, Philadelphia, PA 19104 (United States); Wen, Ten-Chin, E-mail: tcwen@mail.ncku.edu.t [Department of Chemical Engineering, National Cheng Kung University, Tainan 70101, Taiwan (China); Wang, Tzong-Liu; Shieh, Yeong-Tarng [Department of Chemical and Materials Engineering, National University of Kaohsiung, Kaohsiung 81148, Taiwan (China); Lin, Wen-Churng [Department of Environmental Engineering, Kun Shan University, Tainan 71016, Taiwan (China); Chen, Wen-Janq [Department of Chemical and Materials Engineering, National University of Kaohsiung, Kaohsiung 81148, Taiwan (China)

    2011-02-01

    A biosensor electrode possessing highly sensitive and selective determination of dopamine (DA) is fabricated. This electrode, a silver (Ag) thin film on indium-tin-oxide glass, is treated with a silver sulfide (Ag{sub 2}S) film using electrochemical deposition. Active Ag ion is easier to form on Ag{sub 2}S than on pristine Ag, which prefers to attract ascorbic acid (AA). The Ag{sub 2}S layer reduces the oxidation potential of AA due to the electrostatic interaction, which results in well-separation of mixed oxidation responses to both of DA and AA. Besides, the Ag{sub 2}S-modified electrode exhibits dramatic electrocatalytic effect on the oxidation of DA in the presence of AA. In 0.1 M phosphate buffer solution at pH {approx} 7.0, the differential pulse voltammetric peak intensity linearly correlates with DA concentration in two regions, viz. 1.0-10, and 10-100 {mu}M, with correlation coefficient of 0.998 and 0.995, respectively. The lowest concentration limit of 1.0 {mu}M DA can be detected. The interference of AA effectively diminishes in the mixed solution. These features make the Ag{sub 2}S significant for selective and sensitive measurement of DA in the presence of excess AA.

  1. [Electrochemical behavior of dopamine at dodecyl benzenesulfonate self-assembled monolayers modified electrode and its application].

    Science.gov (United States)

    Han, Xiao-xia; Gao, Zuo-ning

    2007-04-01

    Sodium dodecyl benzenesulfonate (SDBS) self-assembled monolayers in situ modified electrode (SDBS/CPE) was prepared. The electrochemical behaviors of dopamine (DA) on SDBS/CPE were studied. Electrochemical behaviors and kinetic parameters of DA were investigated at SDBS/CPE by cyclic voltammetry (CV), chronoamperometry (CA) and chronocoulometry (CC). The changes of the oxidation peak currents with concentration of DA were examined by square wave voltametry (SWV). The difference of peak potential at CPB/CPE was less than 149 mV comparing with that at CPE. The charge transfer coefficient alpha, diffusion coefficient D and the apparent reaction rate constant k(f) are 0.61, 3.6 x 10(-5) cm2 x s(-1) and 4.2 x 10(-3) cm x s(-1), respectively. The oxidation peak currents of DA versus its concentration have a good linear relationship in the concentration range of 2.0 x 10(-6)-1.0 x 10(-3) mol x L(-1) with the correlation coefficient of 0.9979 and the detection limit of 9.0 x 10(-7) mol x L(-1) by square wave voltammetry (SWV) response. The modified electrode showed an excellent electrocatalytic activity for the DA electrochemical oxidation. The method can be applied in the determination of DA in injection samples with the satisfactory results.

  2. Binary self-assembled monolayers modified Au nanoparticles as carriers in biological applications.

    Science.gov (United States)

    Chang, Hsun-Yun; You, Yun-Wen; Liao, Hua-Yang; Shyue, Jing-Jong

    2014-12-01

    Gold nanoparticles (AuNPs) are good nonviral carriers because of their ease of synthesis and conjugation in biochemistry, and self-assembled monolayers (SAMs) provide a tunable system to change their interfacial properties. Using homogeneously mixed carboxylic acid and amine functional groups, a series of surface potentials and isoelectric points (IEPs) could be obtained and allow systematic study of the effect of surface potential. In this work, the result of the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay revealed that binary-SAM modified AuNPs have high biocompatibility with HEK293T cells. The amount of AuNPs ingested by the cells was found to increase with increasing surface potential and the difference was also confirmed with a scanning transmission electron microscope. The ability of binary-SAM modified AuNPs as carriers was examined, and the plasmid deoxyribose nucleic acid (DNA)-containing eGFP reporter gene was used as the model cargo. Fluorescence imaging revealed that the transfection efficiency generally increased with increasing surface potential. More importantly, when the IEP of the AuNPs was higher than that of the environment of the endosome but lower than that of the cytoplasm, the plasmid DNA can be protected better and released more easily during the endocytosis process hence higher efficiency is obtained with 60% NH2 and 40% COOH in the binary-SAM.

  3. Improving performance, stability, and processability of OFETs with printed Ag electrodes by means of a novel, multipurpose self-assembled monolayer (Conference Presentation)

    Science.gov (United States)

    Alt, Milan; Jesper, Malte; Schinke, Janusz; Hillebrandt, Sabina; Reiser, Patrick; Rödlmeier, Tobias; Angelova, Iva; Hamburger, Manuel; Lemmer, Ulrich; Hernandez-Sosa, Gerardo; Lovrincic, Robert

    2016-11-01

    We present a novel SAM-forming molecule bisjulolidyldisulfide that reduces the WF of metal surfaces by 1.2 eV and can lower the barrier for electron injection to organic semiconductors. Applied to Au and Ag surfaces, including inkjet-printed Ag on PET, we characterized bisjulolidyldisulfide monolayers by means of photoelectron spectroscopy (PES) and sessile drop technique, as well as their influence on the performance of n-type OFETs. Next a strong reduction of the contact resistance by two orders of magnitude, we found that this SAM treatment extends the shelf lifetime of ambient-stored OFET devices. Also, it improves the wettability and thereby facilitates solution processing of a subsequent layer with respect to the untreated surface. The full electrical functionality of bisjulolidyldisulfide SAMs was found to become manifest with only one minute of immersion in ethanol solution. PES measurements suggests that the surface coverage is thorough on Au, but only fractional on Ag, especially on printed Ag. However, the quality of SAM-treated bottom contacts in n-type OFETs is very similar for all three investigated metal surfaces (Au and Ag evaporated and printed Ag). This is especially important for printed Ag-electrodes, as their surface was found to be significantly worse for device performance in comparison to their evaporated Ag counterpart. Using this surface treatment we realized integrated unipolar n-type ring oscillators with inkjet printed Ag electrodes.

  4. Exciton-plasmon Coupling and Electromagnetically Induced Transparency in Monolayer Semiconductors Hybridized with Ag Nanoparticles

    CERN Document Server

    Weijie, Zhao; Bo, Liu; Ivan, Verzhbitskiy; Shisheng, Li; Francesco, Giustiniano; Daichi, Kozawa; Ping, Loh Kian; Kazunari, Matsuda; Koichi, Okamoto; Rupert, Oulton F; Goki, Eda

    2016-01-01

    Hybrid systems of excitons strongly coupled to localized surface plasmons supported by metallic nanoparticles define a new approach to control light-matter interactions. Here, we report exciton-plasmon coupling in two-dimensional (2D) semiconductors, such as MoS2 and WS2, hybridized with silver nanoparticles. Prominent photoluminescence enhancement in monolayer MoS2 was observed with localized surface plasmon resonance (LSPR) tuned to the exciton resonance. By tuning the excitation energy, the contributions from near field enhancement and radiative emission rate enhancement via Purcell effect were resolved. Strong coherent dipole-dipole coupling between excitons and LSPR in resonant condition manifests as an electromagnetically induced transparency window in the extinction spectra of the localized surface plasmon. In this strong coupling regime a new quasi-particle, known as a plexciton, is expected to exhibit distinct properties, which exist in neither of the original particles. Our results demonstrate that ...

  5. Improved DET communication between cellobiose dehydrogenase and a gold electrode modified with a rigid self-assembled monolayer and green metal nanoparticles: The role of an ordered nanostructuration.

    Science.gov (United States)

    Bollella, P; Mazzei, F; Favero, G; Fusco, G; Ludwig, R; Gorton, L; Antiochia, R

    2017-02-15

    Efficient direct electron transfer (DET) between cellobiose dehydrogenase from Corynascus thermophilus (CtCDH) and a novel gold electrode platform, obtained by covalent linking of green AuNPs and AgNPs modified with a dithiol self-assembled monolayer, consisting of biphenyl-4,4'-dithiol (BPDT), was presented. The green AuNPs and AgNPs were synthesized using quercetin as reducing agent at room temperature. TEM experiments showed that the AuNPs and AgNPs were circular in shape with an average diameter of 5 and 8nm, respectively. Cyclic voltammetry of CtCDH immobilized onto the AuNPs/BPDT/AuE and the AgNPs/BPDT/AuE electrode platforms were carried out and compared with naked AuE, BPDT/AuE, AuNPs/AuE, and AgNPs/AuE. A pair of well-defined redox waves in neutral pH solution due to efficient DET of CtCDH was present with both MNPs/BPDT/AuE platforms. No DET communication was found with platforms without MNPs linked to BPDT. The apparent heterogeneous electron transfer rate constants (kS) of CtCDH were calculated to be 21.5±0.8s(-1) and 10.3±0.7s(-1), for the AuNPs/BPDT/AuE and the AgNPs/BPDT/AuE platforms, respectively. The modified electrodes were successively used to develop an eco-friendly biosensor for lactose detection. The CtCDH/AuNPs/BPDT/AuE based biosensor showed the best analytical performances with an excellent stability, a detection limit of 3µM, a linear range between 5 and 400µM and a sensitivity of 27.5±2.5µAcm(-2)mM(-1). Such performances were favorably compared with other lactose biosensors reported in literature. The biosensor was successively tested to quantify lactose content in real milk and cream samples. No significant interference present in the sample matrices was observed.

  6. Catalytic cracking of 1-butene to propylene by Ag modified HZSM-5

    Institute of Scientific and Technical Information of China (English)

    Rongrong Zhang; Zhengbao Wang

    2015-01-01

    Silver modified HZSM-5 (AgHZ) zeolite catalysts were prepared by ion exchange method and their catalytic properties in the 1-butene cracking reaction were measured. The catalysts were characterized by infrared spec-troscopy with pyridine adsorption (Py-IR), N2 adsorption and X-ray diffraction (XRD). The effects of Ag loading and steaming treatment on catalytic performances were studied. It is found that the activity of HZSM-5 (HZ) cat-alyst significantly decreases with the steaming time, whereas AgHZ catalysts show stable activity in the steaming time of 24–48 h and their activities increase with the Ag loading. When the steaming time is 24–48 h, the yield of propylene over HZ catalyst significantly decreases, whereas it is stable over AgHZ catalysts. The AgHZ catalysts with Ag loadings of 0.28%–0.43%(by mass) show similar propylene yields (~30%), which are higher than that over the AgHZ catalyst with a Ag loading of 0.55%(by mass). These results indicate that the steam-treated AgHZ catalysts with optimum Ag loadings have higher yield of propylene and are more stable than the steam-treated HZ catalyst. The regeneration stability measurement in butene cracking also shows that the AgHZ catalyst steam-treated under a suitable condition has better stability than the HZ catalyst.

  7. Two-dimensional Pb–Sn alloy monolayer films on Ag(1 1 1)

    Energy Technology Data Exchange (ETDEWEB)

    Yuhara, J., E-mail: j-yuhara@nagoya-u.jp; Ako, T.

    2015-10-01

    Highlights: • Both Pb and Sn films form a hexagonal close-packed structure on Ag(1 1 1). • The 2D binary films of Pb and Sn exhibit an incommensurate structure close to (√13 × √13). • The binary 2D film is considered to follow the Hume-Rothery rule. - Abstract: Single and binary two-dimensional (2D) films of Pb and Sn on Ag(1 1 1) prepared at room temperature have been investigated using low-energy electron diffraction (LEED) and scanning tunneling microscopy. (√28 × √28)-Pb is observed in addition to (√3 × √3)-Pb at coverages higher than 0.35 ML. The nominal coverages for the (√28 × √28)-Pb and (√3 × √3)-Pb structures are determined to be 0.68 and 1/3 ML, respectively. The (1 × 1)-Sn structure is formed at coverages less than 1 ML. Both Pb and Sn films form a hexagonal close-packed structure on Ag(1 1 1). When the Sn coverage increases to more than 1 ML, excess Sn atoms form a (√3 × √3) structure on the (1 × 1)-Sn surface. The 2D binary films exhibit an incommensurate structure close to (√13 × √13) at Pb and Sn coverages of 0.5 and 0.25 ML, respectively. Atomic-resolution STM images exhibit a hexagonal close-packed structure. From the DFT total energy calculations, it is concluded that the Pb and Sn atoms of the (“√13 × √13″) structure do not form an ordered alloy but, rather, form a solid solution alloy. From these results, it is concluded that the binary 2D films also follow the Hume-Rothery rule.

  8. Dithiocarbamate Self-Assembled Monolayers as Efficient Surface Modifiers for Low Work Function Noble Metals.

    Science.gov (United States)

    Meyer, Dominik; Schäfer, Tobias; Schulz, Philip; Jung, Sebastian; Rittich, Julia; Mokros, Daniel; Segger, Ingolf; Maercks, Franziska; Effertz, Christian; Mazzarello, Riccardo; Wuttig, Matthias

    2016-09-06

    Tuning the work function of the electrode is one of the crucial steps to improve charge extraction in organic electronic devices. Here, we show that N,N-dialkyl dithiocarbamates (DTC) can be effectively employed to produce low work function noble metal electrodes. Work functions between 3.1 and 3.5 eV are observed for all metals investigated (Cu, Ag, and Au). Ultraviolet photoemission spectroscopy (UPS) reveals a maximum decrease in work function by 2.1 eV as compared to the bare metal surface. Electronic structure calculations elucidate how the complex interplay between intrinsic dipoles and dipoles induced by bond formation generates such large work function shifts. Subsequently, we quantify the improvement in contact resistance of organic thin film transistor devices with DTC coated source and drain electrodes. These findings demonstrate that DTC molecules can be employed as universal surface modifiers to produce stable electrodes for electron injection in high performance hybrid organic optoelectronics.

  9. Dithiocarbamate Self-Assembled Monolayers as Efficient Surface Modifiers for Low Work Function Noble Metals

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Dominik; Schäfer, Tobias; Schulz, Philip; Jung, Sebastian; Rittich, Julia; Mokros, Daniel; Segger, Ingolf; Maercks, Franziska; Effertz, Christian; Mazzarello, Riccardo; Wuttig, Matthias

    2016-09-06

    Tuning the work function of the electrode is one of the crucial steps to improve charge extraction in organic electronic devices. Here, we show that N,N-dialkyl dithiocarbamates (DTC) can be effectively employed to produce low work function noble metal electrodes. Work functions between 3.1 and 3.5 eV are observed for all metals investigated (Cu, Ag, and Au). Ultraviolet photoemission spectroscopy (UPS) reveals a maximum decrease in work function by 2.1 eV as compared to the bare metal surface. Electronic structure calculations elucidate how the complex interplay between intrinsic dipoles and dipoles induced by bond formation generates such large work function shifts. Subsequently, we quantify the improvement in contact resistance of organic thin film transistor devices with DTC coated source and drain electrodes. These findings demonstrate that DTC molecules can be employed as universal surface modifiers to produce stable electrodes for electron injection in high performance hybrid organic optoelectronics.

  10. Electrochemical Behavior and Determination of Trifluoperazine at Decanethiol Self- Assembled Monolayer Modified Gold Electrodes

    Institute of Scientific and Technical Information of China (English)

    HUANG Fei; YAN Quan-ping; ZENG Bai-zhao

    2005-01-01

    The electrochemical behavior of trifluoperazine at decanethiol self-assembled monolayer (SAM) modified gold electrodes (i. e. C10 H21 SH/Au) has been studied. Trifluoperazine can effectively accumulate on C10 H21 SH/Au elec trodes and generate a sensitive anodic peak at about 0. 63 V (vs. SCE) in 0.05 mol/L pH 9.4 Na2B4O7 buffer solution.Under the selected conditions, the anodic peak current was linear to trifluoperazine concentration in the range of 5.0 ×10 7-3. 0× 10-5 mol/L with correlation coefficient of 0. 997,the detection limit was 3.0 × 10-8 mol/L. This method was applied to the determination of trifluoperazine in drug samples and the recovery was 97.3%-104.0%. It was found that sodium dodecyl sulfate (SDS) could make the anodic peak current increase. In the presence of SDS, the peak at about 0.63V turned into two peaks, resulting from the change of the electrochemical mechanism.

  11. Theoretic insights into the Ag doping in monolayer and bilayer ZnO armchair nanoribbons: edge effect and position-dependent properties

    Energy Technology Data Exchange (ETDEWEB)

    Li Yanlu [Shandong University, Department of Chemistry and Chemical Engineering (China); Zhao Xian; Cheng Xiufeng [Shandong University, State Key Laboratory of Crystal Materials (China); Fan Weiliu, E-mail: fwl@sdu.edu.cn [Shandong University, Department of Chemistry and Chemical Engineering (China)

    2012-10-15

    One-dimensional nanoribbons, thickness of which is smaller than width, exhibit special confinement and edge effects far from uniform in the cross-section. By means of density functional theory, we investigated the influence of the edges and doping positions on the electronic structure of Ag-doped ZnO armchair nanoribbons (ZnOANRs). Ag doping in monolayer and bilayer ZnOANRs (m- and b-ZnOANRs) have all been examined. The results indicated that there is no significant difference on the stability of Ag doping in different positions of both m- and b-ZnOANRs, but exhibits very different electronic properties directly related to the different doping positions. The depth of the acceptor states has essential relationship with the interaction between host O 2p and Ag 4d states in the acceptor. Ag substituting Zn atoms at the inner region of m-ZnOANRs could create shallow acceptors with small hole effective masses, benefit for p-type conduction. Ag doping in the inner region of b-ZnOANRs would create shallow acceptors but larger hole effective masses. The difficulty of hole mobility could be improved by increasing the Ag doping concentration in b-ZnOANRs. The discussion about the mechanism and the suggestion about the achievement in the experiment are interesting and timely.

  12. Electrochemical Glucose Oxidation Using Glassy Carbon Electrodes Modified with Au-Ag Nanoparticles: Influence of Ag Content

    Directory of Open Access Journals (Sweden)

    Nancy Gabriela García-Morales

    2015-01-01

    Full Text Available This paper describes the application of glassy carbon modified electrodes bearing Aux-Agy nanoparticles to catalyze the electrochemical oxidation of glucose. In particular, the paper shows the influence of the Ag content on this oxidation process. A simple method was applied to prepare the nanoparticles, which were characterized by transmission electron microscopy, Ultraviolet-Visible spectroscopy, X-ray diffraction spectroscopy, and cyclic voltammetry. These nanoparticles were used to modify glassy carbon electrodes. The effectiveness of these electrodes for electrochemical glucose oxidation was evaluated. The modified glassy carbon electrodes are highly sensitive to glucose oxidation in alkaline media, which could be attributed to the presence of Aux-Agy nanoparticles on the electrode surface. The voltammetric results suggest that the glucose oxidation speed is controlled by the glucose diffusion to the electrode surface. These results also show that the catalytic activity of the electrodes depends on the Ag content of the nanoparticles. Best results were obtained for the Au80-Ag20 nanoparticles modified electrode. This electrode could be used for Gluconic acid (GA production.

  13. Voltammetric Detection of Urea on an Ag-Modified Zeolite- Expanded Graphite-Epoxy Composite Electrode

    NARCIS (Netherlands)

    Manea, F.; Pop, A.; Radovan, C.; Malchev, P.G.; Bebeselea, A.; Burtica, G.; Picken, S.J.; Schoonman, J.

    2008-01-01

    In this paper, a modified expanded graphite composite electrode based on natural zeolitic volcanic tuff modified with silver (EG-Ag-Z-Epoxy) was developed. Cyclic voltammetry measurements revealed a reasonably fast electron transfer and a good stability of the electrode in 0.1 M NaOH supporting elec

  14. Synthesis of Ag2O and Ag co-modified flower-like SnS2 composites with enhanced photocatalytic activity under solar light irradiation

    Science.gov (United States)

    Deng, Lu; Zhu, Zhenfeng; Liu, Liu; Liu, Hui

    2017-01-01

    Three-dimensional Ag2O and Ag co-modified flower-like SnS2 composites have been synthesized through a facile hydrothermal and photoreduction process. The physical and chemical properties of Ag2O and Ag co-modified flower-like SnS2 composites were carefully studied by using XRD, SEM, TEM, UV-vis diffuse reflectance spectra (DRS) and XPS. The photocatalytic activity of the as-prepared products was evaluated by photocatalytic decolorization of Rhodamine B (Rh B) aqueous solution at ambient temperature under solar light irradiation. The photocatalytic result shows that Ag2O and Ag co-modified flower-like SnS2 composites exhibit enhanced photocatalytic activity compared with that of pure SnS2. Three of the Ag2O and Ag co-modified flower-like SnS2 composites form the Z-scheme systems, because of their unique charge-carrier transfer process, the oxidation/reduction ability of photogenerated holes and electrons could be enhanced. Therefore, the new Ag2O and Ag co-modified flower-like SnS2 composites possess a favorable photocatalytic activity, and it can be a promising candidate for the solar energy conversion process.

  15. Copper Contamination of Self-Assembled Organic Monolayer Modified Silicon Surfaces Following a "Click" Reaction Characterized with LAPS and SPIM.

    Science.gov (United States)

    Wu, Fan; Zhang, De-Wen; Wang, Jian; Watkinson, Michael; Krause, Steffi

    2017-04-04

    A copper(I)-catalyzed azide alkyne cycloaddition (CuAAC) reaction combined with microcontact printing was used successfully to pattern alkyne-terminated self-assembled organic monolayer-modified silicon surfaces. Despite the absence of a copper peak in X-ray photoelectron spectra, copper contamination was found and visualized using light-addressable potentiometric sensors (LAPS) and scanning photo-induced impedance microscopy (SPIM) after the "click"-modified silicon surfaces were rinsed with hydrochloric acid (HCl) solution, which was frequently used to remove copper residues in the past. Even cleaning with an ethylenediaminetetraacetic acid (EDTA) solution did not remove the copper residue completely. Different strategies for avoiding copper contamination, including the use of bulky chelators for the copper(I) catalyst and rinsing with different reagents, were tested. Only cleaning of the silicon surfaces with an EDTA solution containing trifluoroacetic acid (TFA) after the click modification proved to be an effective method as confirmed by LAPS and SPIM results, which showed the expected potential shift due to the surface charge introduced by functional groups in the monolayer and allowed, for the first time, imaging the impedance of an organic monolayer.

  16. The role of surface Pt on the coadsorption of hydrogen and CO on Pt monolayer film modified Ru(0001) surfaces

    Science.gov (United States)

    Diemant, T.; Hartmann, H.; Bansmann, J.; Behm, R. J.

    2016-10-01

    We have investigated the impact and role of the Pt surface modification on the coadsorption of hydrogen and CO on structurally well defined bimetallic Pt monolayer island/film modified Ru(0001) surfaces with Pt contents up to a complete Pt layer, employing temperature programmed desorption (TPD) and infrared reflection absorption spectroscopy (IRRAS). Kinetic limitations in the surface diffusion are shown to play an important role for adsorption at 90 K, and lead to profound effects of the dosing sequence on the adsorption and desorption characteristics. Furthermore, they are responsible for spill-over effects during the TPD measurements, where COad becomes mobile and can spill-over from weakly bonding Pt monolayer areas to strongly bonding Pt-free Ru(0001) areas, which displaces Dad from these surface areas. The present findings are discussed in comparison with previous results on related metallic and bimetallic adsorption and coadsorption systems.

  17. Application of a gold electrode, modified by a self-assembled monolayer of 2-mercaptodecylhydroquinone, to the electroanalysis of hemoglobin.

    Science.gov (United States)

    Zhang, Jingdong; Seo, Kyoungja; Jeon, Il Cheol

    2003-02-01

    A gold electrode modified by a self-assembled monolayer of 2-mercaptodecylhydroquinone (H(2)Q(CH(2))(10)SH) was applied to investigate the electrochemical response of hemoglobin in aerated buffer solutions. Compared with a bare gold electrode, the monolayer of H(2)Q(CH(2))(10)SH could suppress the reduction wave of dissolved oxygen in the buffer while effectively promoting the rate of electron transfer between hemoglobin and the electrode. Thus, a convenient way for electroanalysis of hemoglobin in air was achieved at the H(2)Q(CH(2))(10)SH/Au electrode. A linear relationship existed between peak current and concentration of hemoglobin in the range 1 x 10(-7)-1 x 10(-6) mol L(-1).

  18. Modified embedded-atom potential for B2-MgAg

    Science.gov (United States)

    Groh, Sébastien

    2016-08-01

    Interatomic potentials for pure Ag and Mg-Ag alloy have been developed in the framework of the second nearest-neighbors modified embedded-atom method (MEAM). The validity and the transferability of the Ag potential were obtained by calculating physical, mechanical, thermal, and dislocation related properties. Since the {1 1 1}-generalized stacking fault energy curves obtained from first-principle calculations was used to develop the Ag potential, the critical resolved shear stress to move screw dislocations in Ag single crystal is in good agreement with the experimental data. By combining the ability of the potential to predict the surface energies with its accuracy in describing dislocation properties, the potential is thought to be a predictive model for analyzing the fracture properties of Ag. In addition, the performance of the potential was tested under dynamics conditions by predicting the melting temperature, where a good agreement with experimental value was found. The Ag-MEAM potential was then coupled to an existing Mg-MEAM potential to describe the properties of the binary system MgAg. While the heat of formation, the elastic constants, and the (1 1 0) γ-surface of the MgAg compound in the B2 phase were used to parameterize the potential, heat of formation for MgAg alloys with different stoichiometry, thermal properties of the B2-MgAg compound, as well as dislocation related properties in B2-MgAg compound were tested to validate the transferability of the potential. The heat of formation of Mg5Ag2, MgAg, and MgAg3, the elastic constants and the thermal properties of B2-MgAg obtained with the proposed potential align with first-principles and experimental data. In addition, the core structure of both and dislocations in {1 1 0} are in agreement with theoretical predictions, and the magnitudes of the critical resolved shear stress obtained at 0 K for both slip systems partially validate the slip behavior of B2-MgAg. Furthermore, the

  19. ELECTROCHEMICAL OXIDATION OF ETHYLENE AT PANI/Pt AND Ag/PANI/Pt MODIFIED ELECTRODES

    Directory of Open Access Journals (Sweden)

    Lenys Fernández

    Full Text Available The electrochemical behavior of ethylene on PANI/Pt and Ag/PANI/Pt modified electrodes was investigated in different media. Morphology of the deposits of PANI were observed by SEM analysis, complemented by the EDX techniques to obtain the Ag composition that shows that Ag is deposited in the polymeric matrix which covered the whole platinum surface. The electrodic system comprising Ag/PANI/ Pt electrode exhibited a more important electrocatalytic response for ethylene oxidation in neutral solutions than the PAN/Pt and Pt electrodes at 20 ºC.The results suggest that the oxidation of ethylene on Ag/PANI/Pt electrode is limited by adsorption-controlled reaction while the oxidation at PANI/Pt is mass transport-limited.

  20. Enhanced visible-light photocatalytic performances of Ag3PO4 surface-modified with small amounts of TiO2 and Ag

    Science.gov (United States)

    Wang, Desong; Li, Lei; Luo, Qingzhi; An, Jing; Li, Xueyan; Yin, Rong; Zhao, Mangmang

    2014-12-01

    A novel approach has been developed to prepare an efficient visible-light photocatalyst using Ag3PO4 and TiO2 sol as precursors. First, Ag3PO4 particles were dipped into TiO2 sol for 5 min and were filtered quickly. Second, Ag3PO4 particles adsorbing a small amount of TiO2 sol were aged for 24 h to form TiO2 gel on their surface. Finally, Ag3PO4 particles covered by TiO2 gel were calcined at 450 °C for 2 h to obtain the surface-modified Ag3PO4 sample. The surface-modified Ag3PO4 was characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, UV-vis diffuse reflection spectroscopy, X-ray photoelectron spectroscopy, and electrochemical impedance spectroscopy. The visible-light photocatalytic performances of the surface-modified Ag3PO4 were evaluated by the photodegradation of methyl orange or phenol solution. The results showed that the surface-modified Ag3PO4 exhibited much higher visible-light photocatalytic activity and stability than pure Ag3PO4. As the amount of TiO2 gel on the Ag3PO4 surface increased, the visible-light photocatalytic activity increased first and then decreased. The surface-modification of Ag3PO4 obviously decreased its solubility in water environment due to the protection of TiO2 and Ag nanocrystals on the surface. The visible-light photocatalytic mechanism of the surface-modified Ag3PO4 has been discussed.

  1. Scalable Synthesis of Ag Networks with Optimized Sub-monolayer Au-Pd Nanoparticle Covering for Highly Enhanced SERS Detection and Catalysis

    Science.gov (United States)

    Li, Tianyu; Vongehr, Sascha; Tang, Shaochun; Dai, Yuming; Huang, Xiao; Meng, Xiangkang

    2016-11-01

    Highly porous tri-metallic AgxAuyPdz networks with a sub-monolayer bimetallic Au-Pd nanoparticle coating were synthesized via a designed galvanic replacement reaction of Ag nanosponges suspended in mixed solutions of HAuCl4 and K2PdCl4. The resulting networks’ ligaments have a rough surface with bimetallic nanoparticles and nanopores due to removal of Ag. The surface morphology and composition are adjustable by the temperature and mixed solutions’ concentration. Very low combined Au and Pd atomic percentage (1-x) where x is atomic percentage of Ag leads to sub-monolayer nanoparticle coverings allowing a large number of active boundaries, nanopores, and metal-metal interfaces to be accessible. Optimization of the Au/Pd atomic ratio y/z obtains large surface-enhanced Raman scattering detection sensitivity (at y/z = 5.06) and a higher catalytic activity (at y/z = 3.55) toward reduction reactions as benchmarked with 4-nitrophenol than for most bimetallic catalysts. Subsequent optimization of x (at fixed y/z) further increases the catalytic activity to obtain a superior tri-metallic catalyst, which is mainly attributed to the synergy of several aspects including the large porosity, increased surface roughness, accessible interfaces, and hydrogen absorption capacity of nanosized Pd. This work provides a new concept for scalable synthesis and performance optimization of tri-metallic nanostructures.

  2. Promising monolayer membranes for CO2/N2/CH4 separation: Graphdiynes modified respectively with hydrogen, fluorine, and oxygen atoms

    Science.gov (United States)

    Zhao, Lianming; Sang, Pengpeng; Guo, Sheng; Liu, Xiuping; Li, Jing; Zhu, Houyu; Guo, Wenyue

    2017-05-01

    Three graphdiyne-like monolayers were designed by substituting one-third diacetylenic linkages with heteroatoms hydrogen, fluorine, and oxygen (GDY_X, X = H, F, and O), respectively. The CO2/N2/CH4 separation performance of the designed graphdiyne-like monolayers was investigated by using both first-principle density functional theory (DFT) and molecular dynamic (MD) simulations. The stabilities of GDY_X monolayers were confirmed by the calculated cohesive energies and phonon dispersion spectra. Both the DFT and MD calculations demonstrated that although the GDY_H membrane has poor selectivity for CO2/N2/CH4 gases, the GDY_F and GDY_O membranes can excellently separate CO2 and N2 from CH4 in a wide temperature range. Moreover, the CO2/N2 mixture can be effectively separated by GDY_O at temperatures lower than 300 K. Based on the kinetic theory, extremely high permeances were found for CO2 and N2 passing through the GDY_X membranes (10-4-10-2 mol/m2 s Pa at 298 K). In addition, the influence of relative concentration on selectivity was also investigated for gases in the binary mixtures. This work provides an effective way to modify graphdiyne for the separation of large molecular gases, which is quite crucial in the gas separation industry.

  3. Electron transport nonlocality in monolayer graphene modified with hydrogen silsesquioxane polymerization

    NARCIS (Netherlands)

    Kaverzin, A. A.; van Wees, B. J.

    2015-01-01

    A number of practical and fundamental applications of graphene requires modification of some of its properties. In this paper we study the effect of polymerization of a hydrogen silsesquioxane film on top of monolayer graphene with the intent to increase the strength of the spin-orbit interaction. T

  4. Facile Synthesis of Mono-Dispersed Polystyrene (PS/Ag Composite Microspheres via Modified Chemical Reduction

    Directory of Open Access Journals (Sweden)

    Wen Zhu

    2013-12-01

    Full Text Available A modified method based on in situ chemical reduction was developed to prepare mono-dispersed polystyrene/silver (PS/Ag composite microspheres. In this approach; mono-dispersed PS microspheres were synthesized through dispersion polymerization using poly-vinylpyrrolidone (PVP as a dispersant at first. Then, poly-dopamine (PDA was fabricated to functionally modify the surfaces of PS microspheres. With the addition of [Ag(NH32]+ to the PS dispersion, [Ag(NH32]+ complex ions were absorbed and reduced to silver nanoparticles on the surfaces of PS-PDA microspheres to form PS/Ag composite microspheres. PVP acted both as a solvent of the metallic precursor and as a reducing agent. PDA also acted both as a chemical protocol to immobilize the silver nanoparticles at the PS surface and as a reducing agent. Therefore, no additional reducing agents were needed. The resulting composite microspheres were characterized by TEM, field emission scanning electron microscopy (FESEM, energy-dispersive X-ray spectroscopy (EDS, XRD, UV-Vis and surface-enhanced Raman spectroscopy (SERS. The results showed that Ag nanoparticles (NPs were homogeneously immobilized onto the PS microspheres’ surface in the presence of PDA and PVP. PS/Ag composite microspheres were well formed with a uniform and compact shell layer and were adjustable in terms of their optical property.

  5. Synthesis and Characterization of Ag-Modified V2O5 Photocatalytic Materials

    Directory of Open Access Journals (Sweden)

    Dora Alicia Solis-Casados

    2017-01-01

    Full Text Available V2O5 powders modified with different theoretical silver contents (1, 5, 10, 15, and 20 wt% as Ag2O were obtained with acicular morphologies observed by scanning electron microscopy (SEM. Shcherbinaite crystalline phase is transformed into the Ag0.33V2O5 crystalline one with the incorporation and increase in silver content as was suggested by X-ray diffraction (XRD and X-ray photoelectron spectroscopy (XPS analysis. With further increase in silver contents the Ag2O phase appears. Catalysts were active in photocatalytic degradation of malachite green dye under simulated solar light, which is one of the most remarkable facts of this work. It was found that V2O5-20Ag was the most active catalytic formulation and its activity was attributed to the mixture of coupled semiconductors that promotes the slight decrease in the rate of the electron-hole pair recombination.

  6. Sputtered Ag thin films with modified morphologies: Influence on wetting property

    Energy Technology Data Exchange (ETDEWEB)

    Dutheil, P., E-mail: perrine.dutheil@univ-orleans.fr [GREMI, UMR 7344- Université D’Orléans, 14 rue d’Issoudun, BP 6744, Orléans 45067 (France); Thomann, A.L.; Lecas, T.; Brault, P. [GREMI, UMR 7344- Université D’Orléans, 14 rue d’Issoudun, BP 6744, Orléans 45067 (France); Vayer, M. [ICMN, UMR 7374- Université D’Orléans, 1b rue de la Férollerie, Orléans 45071 (France)

    2015-08-30

    Graphical abstract: - Highlights: • Ag thin films are deposited by DC magnetron sputtering on Si and W/Si layers. • The influence of the W underlayer morphology on Ag film growth is evidenced. • Variation of the Ag growth mode and roughness is investigated by SEM and AFM. • Wetting property is correlated to the roughness of Ag deposits on Si and W layers. - Abstract: Silver thin films with thickness ranging from 3 nm to 33 nm were sputter deposited onto silicon wafers and tungsten layers. Those W layers were previously synthesized in the same DC magnetron sputter deposition system with various experimental conditions (argon pressure, target to substrate distance) in order to stabilize different surface morphologies. SEM observations and AFM images showed that the growth mode of Ag films is similar on Si substrates and on the smoothest W layers, whereas it is modified for rough W layers made of sharp grains. The effect of the W layer morphology on Ag film growth was clearly evidenced when the deposition took place at high temperature. It is seen that performing the deposition onto substrates of various morphologies allows tailoring the wetting property of the Ag deposit.

  7. Improved charge separation properties of organic hetero-junction solar cells by self-assembled monolayers anchored Ag nanoparticles.

    Science.gov (United States)

    Tai, Yian; Guo, Zong-Ci; Sharma, Jadab

    2011-12-01

    We investigate the effect of self-assembled monolayers and localized surface plasmons of silver nano-particles on an organic solar cell consisting of zinc phthalocyanine as an active layer. The device was fabricated by covalent attachment of silver nanoparticles on n-type silicon substrates using self-assembled monolayer of 4-mercaptophenol. Power conversion efficiency is increased up to 8 times as compared to a reference device with merely 0.13% photo-conversion efficiency containing no self-assembled monolayers and silver nano-particles. We believe that improved conductivity at the interface due to the aromatic self-assembled monolayer and the increased local electric field experienced by the active layer in presence of silver nano-particles act in synergy towards the higher population of excitons and dissipation of charge.

  8. Fabrication, characterization and photocatalytic properties of Ag nanoparticles modified TiO{sub 2} NTs

    Energy Technology Data Exchange (ETDEWEB)

    Wang Qingyao [School of Materials Science and Engineering, Tongji University, Shanghai 201804 (China); Yang Xiuchun, E-mail: yangxc@tongji.edu.cn [School of Materials Science and Engineering, Tongji University, Shanghai 201804 (China); Liu Dan; Zhao Jianfu [School of Materials Science and Engineering, Tongji University, Shanghai 201804 (China)

    2012-06-25

    the SILAR process does not damage the ordered tubular structure. A possible formation mechanism of Ag/TiO{sub 2} NTs has also been proposed. The photocatalytic results showed that the Ag nanoparticle modified TiO{sub 2} NTs largely enhanced the photocatalytic degradation of methyl orange under ultraviolet light irradiation.

  9. A Facile Synthesis of Ag Modified ZnO Nanocrystals with Enhanced Photocatalytic Activity

    Institute of Scientific and Technical Information of China (English)

    DONG Yanling; ZHAN Sha; WANG Ping

    2012-01-01

    Ag modified ZnO (Ag/ZnO) nanocrystals were prepared by a facile and low temperature wet chemical method.The phase structures,morphologies,and optical properties of the as-prepared samples were characterized by X-ray powder diffraction (XRD),field-emission scanning electron microscopy (FESEM),high-resolution transmission electron microscopy (HRTEM),the Brumauer-Emmett-Teller (BET) surface area,UV-vis diffuse reflectance spectroscopy and photoluminescence (PL) spectra,respectively.The photocatalytic performance of Ag/ZnO with diffent Ag contents was measured with the degradation of methyl orange (MO) at room temperature under UV light irradiation.The experimental results indicated that the well-crystalline ZnO nanopaticles with a size of ca.4.5 nm exhibited a high photocatalytic activity for the degradation of MO with the apparent rate constant (k) of 1.57 × 10-2 min-1,and the photocatalytic activities of ZnO were further enhanced by modification with silver.When the Ag loading was 3mo1%,Ag/ZnO showed the highest photocatalytic acitivity with a k value of 5.452× 10-2 min-1,which is 3.5 and 2.5 time more than that of ZnO and commercial P25,respectively.

  10. Preparation and Photocatalytic Activity of Ag Modified Ti-Doped-Bi2O3 Photocatalyst

    Directory of Open Access Journals (Sweden)

    Lilan Zhang

    2014-01-01

    Full Text Available Ti doped Bi2O3 (TDB and Ag ion modified Ti doped Bi2O3 (Ag@TDB photocatalysts were prepared by framework replacement synthesis method with different Ag loadings (0.05, 0.3, 0.75, and 1.0 mol/L AgNO3. The structural properties of the prepared catalysts were studied by scanning electron microscope (SEM, X-ray diffraction (XRD, BET surface area, and UV/Vis diffuse reflectance (DRS. The XRD spectra of the Ti doped Bi2O3 calcined at 650°C showed the diffraction peaks of a mixture of Bi12TiO20 and Bi4Ti3O12, with bits of mixed crystallite consisting of TiO2 and B2O3. A high blue shift in the range 650–550 nm was detected in the DRS band. This blue shift increased with the decreasing Ag content. The photocatalytic activities of the catalysts were evaluated for the degradation of crystal violet (CV under UV light irradiation. The results indicated that the degradation rate of CV by using 1.0 mol/L AgNO3 doped bismuth titanate composite photocatalyst (1.0 Ag@TDB was 1.9 times higher than that by using the bare Ti doped Bi2O3 photocatalyst. The higher activity of Ag@TDB is due to the enhancement of electron-hole pair separation by the electron trapping of silver particles.

  11. Fabrication of a Polyaniline Ultramicroelectrode via a Self Assembled Monolayer Modified Gold Electrode

    Science.gov (United States)

    Bolat, Gulcin; Kuralay, Filiz; Eroglu, Gunes; Abaci, Serdar

    2013-01-01

    Herein, we report a simple and inexpensive way for the fabrication of an ultramicroelectrode and present its characterization by electrochemical techniques. The fabrication of polyaniline UME involves only two steps: modification of a gold (Au) electrode by self assembled monolayers (SAM) and then electrodeposition of polyaniline film on this thiol-coated Au electrode by using cyclic voltammetry and constant potential electrolysis methods. Two types of self-assembled monolayers (4-mercapto-1-butanol, MB, and 11-mercaptoundecanoic acid, MUA) were used, respectively, to see the effect of chain length on microelectrode formation. Microelectrode fabrication and utility of the surface was investigated by cyclic voltammetric measurements in a redox probe. The thus prepared polyaniline microelectrode was then used for DNA immobilization. Discrimination between double-stranded DNA (dsDNA) and single-stranded DNA (ssDNA) was obtained with enhanced electrochemical signals compared to a polyaniline-coated Au electrode. Different modifications on the electrode surfaces were examined using scanning electron microscopy (SEM). PMID:23797740

  12. Gold electrode modified by self-assembled monolayers of thiols to determine DNA sequences hybridization

    Indian Academy of Sciences (India)

    Mízia M S Silva; Igor T Cavalcanti; M Fátima Barroso; M Goreti F Sales; Rosa Fireman Dutra

    2010-11-01

    The process of immobilization of biological molecules is one of the most important steps in the construction of a biosensor. In the case of DNA, the way it exposes its bases can result in electrochemical signals to acceptable levels. The use of self-assembled monolayer that allows a connection to the gold thiol group and DNA binding to an aldehydic ligand resulted in the possibility of determining DNA hybridization. Immobilized single strand of DNA (ssDNA) from calf thymus pre-formed from alkanethiol film was formed by incubating a solution of 2-aminoethanothiol (Cys) followed by glutaraldehyde (Glu). Cyclic voltammetry (CV) was used to characterize the self-assembled monolayer on the gold electrode and, also, to study the immobilization of ssDNA probe and hybridization with the complementary sequence (target ssDNA). The ssDNA probe presents a well-defined oxidation peak at +0.158 V. When the hybridization occurs, this peak disappears which confirms the efficacy of the annealing and the DNA double helix performing without the presence of electroactive indicators. The use of SAM resulted in a stable immobilization of the ssDNA probe, enabling the hybridization detection without labels. This study represents a promising approach for molecular biosensor with sensible and reproducible results.

  13. Modified optical absorption of molecules on metallic nanoparticles at sub-monolayer coverage

    CERN Document Server

    Darby, Brendan L; Meyer, Matthias; Pantoja, Andres E; Ru, Eric C Le

    2015-01-01

    Enhanced optical absorption of molecules in the vicinity of metallic nanostructures is key to a number of surface-enhanced spectroscopies and of great general interest to the fields of plasmonics and nano-optics. Yet, experimental access to this absorbance has long proven elusive. We here present direct measurements of the intrinsic absorbance of dye-molecules adsorbed onto silver nanospheres, and crucially, at sub-monolayer concentrations where dye--dye interactions become negligible. With a large detuning from the plasmon resonance, distinct shifts and broadening of the molecular resonances reveal the intrinsic properties of the dye in contact with the metal colloid, in contrast to the often studied strong-coupling regime where the optical properties of the dye-molecules cannot be isolated. The observation of these shifts together with the ability to routinely measure them has broad implications in the interpretation of experiments involving resonant molecules on metallic surfaces, such as surface-enhanced ...

  14. Electrochemical Study of Biotin-Modified Self-Assembled Monolayers: Recommendations for Robust Preparation

    Directory of Open Access Journals (Sweden)

    Richard J.C. Brown

    2006-01-01

    Full Text Available The development of the underpinning methodology for the production of robust, well-formed, and densely packed biotin-HPDP functionalised gold surfaces, the crucial first step in immobilising bimolecules on surfaces, is described. Self-assembled monolayers (SAMs with biotin end-groups were prepared on polycrystalline gold surfaces according to a published method. The layers formed were studied using cyclic voltammetry to determine the composition of the layer and its quality. Crystal impedance spectroscopy was also applied as a complimentary indicator of the composition of the layer.For the first time, the effect of assembly time on the properties of the layer was studied along with the composition of the layer and the ability of the precursor molecule to self-assemble by oxidative addition.

  15. Effect of surface chemical composition on the work function of silicon substrates modified by binary self-assembled monolayers.

    Science.gov (United States)

    Kuo, Che-Hung; Liu, Chi-Ping; Lee, Szu-Hsian; Chang, Hsun-Yun; Lin, Wei-Chun; You, Yun-Wen; Liao, Hua-Yang; Shyue, Jing-Jong

    2011-09-07

    It has been shown that the application of self-assembled monolayers (SAMs) to semiconductors or metals may enhance the efficiency of optoelectronic devices by changing the surface properties and tuning the work functions at their interfaces. In this work, binary SAMs with various ratios of 3-aminopropyltrimethoxysilane (APTMS) and 3-mercaptopropyltrimethoxysilane (MPTMS) were used to modify the surface of Si to fine-tune the work function of Si to an arbitrary energy level. As an electron-donor, amine SAM (from APTMS) produced outward dipole moments, which led to a lower work function. Conversely, electron-accepting thiol SAM (from MPTMS) increased the work function. It was found that the work function of Si changed linearly with the chemical composition and increased with the concentration of thiol SAMs. Because dipoles of opposite directions cancelled each other out, homogeneously mixing them leads to a net dipole moment (hence the additional surface potential) between the extremes defined by each dipole and changes linearly with the chemical composition. As a result, the work function changed linearly with the chemical composition. Furthermore, the amine SAM possessed a stronger dipole than the thiol SAM. Therefore, the SAMs modified with APTMS showed a greater work function shift than did the SAMs modified with MPTMS.

  16. Ag Nanoparticles-Modified 3D Graphene Foam for Binder-Free Electrodes of Electrochemical Sensors.

    Science.gov (United States)

    Han, Tao; Jin, Jianli; Wang, Congxu; Sun, Youyi; Zhang, Yinghe; Liu, Yaqing

    2017-02-16

    Ag nanoparticles-modified 3D graphene foam was synthesized through a one-step in-situ approach and then directly applied as the electrode of an electrochemical sensor. The composite foam electrode exhibited electrocatalytic activity towards Hg(II) oxidation with high limit of detection and sensitivity of 0.11 μM and 8.0 μA/μM, respectively. Moreover, the composite foam electrode for the sensor exhibited high cycling stability, long-term durability and reproducibility. These results were attributed to the unique porous structure of the composite foam electrode, which enabled the surface of Ag nanoparticles modified reduced graphene oxide (Ag NPs modified rGO) foam to become highly accessible to the metal ion and provided more void volume for the reaction with metal ion. This work not only proved that the composite foam has great potential application in heavy metal ions sensors, but also provided a facile method of gram scale synthesis 3D electrode materials based on rGO foam and other electrical active materials for various applications.

  17. Ag Nanoparticles-Modified 3D Graphene Foam for Binder-Free Electrodes of Electrochemical Sensors

    Science.gov (United States)

    Han, Tao; Jin, Jianli; Wang, Congxu; Sun, Youyi; Zhang, Yinghe; Liu, Yaqing

    2017-01-01

    Ag nanoparticles-modified 3D graphene foam was synthesized through a one-step in-situ approach and then directly applied as the electrode of an electrochemical sensor. The composite foam electrode exhibited electrocatalytic activity towards Hg(II) oxidation with high limit of detection and sensitivity of 0.11 µM and 8.0 µA/µM, respectively. Moreover, the composite foam electrode for the sensor exhibited high cycling stability, long-term durability and reproducibility. These results were attributed to the unique porous structure of the composite foam electrode, which enabled the surface of Ag nanoparticles modified reduced graphene oxide (Ag NPs modified rGO) foam to become highly accessible to the metal ion and provided more void volume for the reaction with metal ion. This work not only proved that the composite foam has great potential application in heavy metal ions sensors, but also provided a facile method of gram scale synthesis 3D electrode materials based on rGO foam and other electrical active materials for various applications.

  18. Multivalent host-guest interactions between ss-cyclodextrin self-assembled monolayers and poly (isobutene-alt-maleic acid)s modified with hydrophobic guest moeties

    NARCIS (Netherlands)

    Crespo biel, O.; Péter, M.; Bruinink, C.M.; Ravoo, B.J.; Reinhoudt, David; Huskens, Jurriaan

    2005-01-01

    Poly(isobutene-alt-maleic acid)s modified with p-tert-butylphenyl or adamantyl groups interact with ß-cyclodextrin self-assembled monolayers (ß-CD SAMs) by inclusion of the hydrophobic substituents in the B-cyclodextrin cavities. The adsorption was shown to be strong, specific, and irreversible.

  19. IMPACT OF POLYCYCLIC AROMATIC HYDROCARBONS OF THE ELECTROCHEMICAL RESPONSES OF A FERRICYNIDE PROBE AT TEMPLATE-MODIFIED SELF ASSEMBLED MONOLAYERS ON GOLD ELECTRODES

    Science.gov (United States)

    The impact of pyrene on the electrochemical response of the ferricyanide probe using Self Assembled Monolayer (SAM)-modified gold electrodes was investigated using Cyclic Voltammetry (CV) and Square Wave Voltammetry (SWV). These results suggest the feasibility of using SAMs, par...

  20. An efficient visible-light photocatalyst prepared by modifying AgBr particles with a small amount of activated carbon

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Desong, E-mail: dswang06@126.com; Zhao, Mangmang; Luo, Qingzhi; Yin, Rong; An, Jing; Li, Xueyan

    2016-04-15

    Highlights: • An efficient visible-light photocatalyst was prepared by modifying AgBr particles. • A small amount of activated carbon was used to modify AgBr particles. • The modified AgBr exhibited improved visible-light photocatalytic performances. - Abstract: An efficient visible-light photocatalyst was successfully prepared by modifying AgBr particles with a small amount of activated carbon (AC) via a simple chemical precipitation approach. The AC/AgBr composite was characterized by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, UV–vis diffuse reflection spectroscopy, photoluminescence spectroscopy, electrochemical impedance spectroscopy. The photocatalytic performances of the AC/AgBr composite were investigated by evaluating photodegradation of methyl orange (MO) and phenol under visible light irradiation, and the effects of the AC content in the composite, concentrations of AC/AgBr composite and MO, carrier scavengers on MO photodegradation rate were systematically investigated. The results indicated that the modification of AC can hardly change the crystalline and crystal size of AgBr particles, while significantly improve their specific surface areas, visible-light absorption and separation efficiency of photogenerated electron–hole pairs. Compared with pure AgBr, the AC/AgBr composite exhibited drastically enhanced visible-light photocatalytic activity and stability. The photogenerated electrons and holes, hydroxyl radicals are responsible to the photodegradation of organic pollutants, and the photogenerated holes are the main active species. On the basis of the results and the properties of AC and AgBr, the visible-light photocatalytic mechanism of the AC/AgBr composite was discussed.

  1. Super-Hydrophobic/Icephobic Coatings Based on Silica Nanoparticles Modified by Self-Assembled Monolayers

    Directory of Open Access Journals (Sweden)

    Junpeng Liu

    2016-12-01

    Full Text Available A super-hydrophobic surface has been obtained from nanocomposite materials based on silica nanoparticles and self-assembled monolayers of 1H,1H,2H,2H-perfluorooctyltriethoxysilane (POTS using spin coating and chemical vapor deposition methods. Scanning electron microscope images reveal the porous structure of the silica nanoparticles, which can trap small-scale air pockets. An average water contact angle of 163° and bouncing off of incoming water droplets suggest that a super-hydrophobic surface has been obtained based on the silica nanoparticles and POTS coating. The monitored water droplet icing test results show that icing is significantly delayed by silica-based nano-coatings compared with bare substrates and commercial icephobic products. Ice adhesion test results show that the ice adhesion strength is reduced remarkably by silica-based nano-coatings. The bouncing phenomenon of water droplets, the icing delay performance and the lower ice adhesion strength suggest that the super-hydrophobic coatings based on a combination of silica and POTS also show icephobicity. An erosion test rig based on pressurized pneumatic water impinging impact was used to evaluate the durability of the super-hydrophobic/icephobic coatings. The results show that durable coatings have been obtained, although improvement will be needed in future work aiming for applications in aerospace.

  2. Electrochemical biosensor modified with dsDNA monolayer for restriction enzyme activity determination.

    Science.gov (United States)

    Zajda, Joanna; Górski, Łukasz; Malinowska, Elżbieta

    2016-06-01

    A simple and cost effective method for the determination of restriction endonuclease activity is presented. dsDNA immobilized at a gold electrode surface is used as the enzymatic substrate, and an external cationic redox probe is employed in voltammetric measurements for analytical signal generation. The assessment of enzyme activity is based on a decrease of a current signal derived from reduction of methylene blue which is present in the sample solution. For this reason, the covalent attachment of the label molecule is not required which significantly reduces costs of the analysis and simplifies the entire determination procedure. The influence of buffer components on utilized dsDNA/MCH monolayer stability and integrity is also verified. Electrochemical impedance spectroscopy measurements reveal that due to pinhole formation during enzyme activity measurement the presence of any surfactants should be avoided. Additionally, it is shown that the sensitivity of the electrochemical biosensor can be tuned by changing the restriction site location along the DNA length. Under optimal conditions the proposed biosensor exhibits a linear response toward PvuII activity within a range from 0.25 to 1.50 U/μL.

  3. Collagen-chitosan scaffold modified with Au and Ag nanoparticles: Synthesis and structure

    Energy Technology Data Exchange (ETDEWEB)

    Rubina, M.S.; Kamitov, E.E. [A.N. Nesmeyanov Institute of Organoelement Compounds, Russian Academy of Sciences, Moscow, 119991 Russian Federation (Russian Federation); Zubavichus, Ya. V.; Peters, G.S. [National Research center «Kurchatov Institute», Moscow, 123182 Russian Federation (Russian Federation); Naumkin, A.V. [A.N. Nesmeyanov Institute of Organoelement Compounds, Russian Academy of Sciences, Moscow, 119991 Russian Federation (Russian Federation); Suzer, S. [Department of Chemistry, Bilkent University, Ankara, 06800 Turkey (Turkey); Vasil’kov, A.Yu., E-mail: alexandervasilkov@yandex.ru [A.N. Nesmeyanov Institute of Organoelement Compounds, Russian Academy of Sciences, Moscow, 119991 Russian Federation (Russian Federation)

    2016-03-15

    Graphical abstract: - Highlights: • Biocompatible collagen-chitosan scaffolds were modified by Au and Ag nanoparticles via the metal-vapor synthesis. • Structural and morphological parameters of the nanocomposites were assessed using a set of modern instrumental techniques, including electron microscopy, X-ray diffraction, small-angle X-ray scattering, EXAFS, XPS. • Potential application of the nanocomposites are envisaged. - Abstract: Nowadays, the dermal biomimetic scaffolds are widely used in regenerative medicine. Collagen-chitosan scaffold one of these materials possesses antibacterial activity, good compatibility with living tissues and has been already used as a wound-healing material. In this article, collagen-chitosan scaffolds modified with Ag and Au nanoparticles have been synthesized using novel method - the metal-vapor synthesis. The nanocomposite materials are characterized by XPS, TEM, SEM and synchrotron radiation-based X-ray techniques. According to XRD data, the mean size of the nanoparticles (NPs) is 10.5 nm and 20.2 nm in Au-Collagen-Chitosan (Au-CollCh) and Ag-Collagen-Chitosan (Ag-CollCh) scaffolds, respectively in fair agreement with the TEM data. SAXS analysis of the composites reveals an asymmetric size distribution peaked at 10 nm for Au-CollCh and 25 nm for Ag-CollCh indicative of particle's aggregation. According to SEM data, the metal-carrying scaffolds have layered structure and the nanoparticles are rather uniformly distributed on the surface material. XPS data indicate that the metallic nanoparticles are in their unoxidized/neutral states and dominantly stabilized within the chitosan-rich domains.

  4. Investigation of Ag-TiO2 nanostructures photocatalytic properties prepared by modified dip coating method

    Science.gov (United States)

    AlArfaj, Esam

    2016-05-01

    In this article, titanium dioxide and silver nanostructures were deposited on glass substrates using modified sol-gel methods and dip-coating technique. The films were characterised chemically and physically using different techniques (TLC, UV-Vis and XRD) and tested for environmental applications regarding degradation of aromatic hydrocarbons. The photocatalytic activity of the TiO2 nanostructures is tested with different small concentrations of phenol in water and reaction mechanisms discussed. Considerable enhancement is observed in the photodegradation activity of Ag-modified (3 wt.%) TiO2 compared to unmodified TiO2 nanostructures for phenol concentrations within the pseudo-first-order Langmuir-Hinshelwood (LH) model for reaction kinetics. The pseudo-first-order global degradation rate constant increased from <0.005 min-1 for TiO2 to 0.013 min-1 for 3 mol% Ag-modified TiO2. The enhancement is attributed to the incorporation of Ag which promotes the generation of reactive oxygen species and increases the carrier recombination life-time. In addition, Ag has been observed to extend the absorption to the visible region by its surface plasmon resonances and to suppress the anatase-rutile phase transformation. Moreover, TiO2 grain size prepared was found to be 10 nm which maximises the active surface area. For phenol initial concentrations as low as 0.0002 M, saturation trend in the degradation process occurred at 0.00014 M and the reaction rate can be fitted with half-order LH kinetics.

  5. Studies on the Electrochemical Behaviour of Hydroquinone at L-cysteine Self-Assembled Monolayers Modified Gold Electrode

    Directory of Open Access Journals (Sweden)

    Dan Du

    2002-02-01

    Full Text Available L-Cysteine is combined onto gold electrode to form a self-assembled monolayers modified electrode (L-Cys/Au SAMs by taking advantage of strong sulfur-gold interaction. ATR-FTIR, SEM, cyclic voltammetry (CV and impedance were used for the characterization of the film. It shows excellent stability upon voltametric scanning and a good voltametric response towards hydroquinone with the potential ranged from 0.8 to –0.2 V (vs.SCE in 0.5M HAc-NaAc buffer solution (pH 4.8. The oxidation potential of hydroquinone on the modified electrode shifted negatively about 330 mV as compared with the bare gold electrode. The plot of catalytic current vs.its concentration has a good linear relation in the range of 2.0×10-6~2.0×10-4M with the correlation coefficient of 0.9986 and the detection limit of 4.0×10-7M by different pulse voltammetry (DPV. Mechanism for the electrocatalytical process has been studied.

  6. Voltametric Behavior of Noradrenaline at 2-Mercaptoethanol Self-Assembled Monolayer Modified Gold Electrode and its Analytical Application

    Directory of Open Access Journals (Sweden)

    ShengFu Wang

    2003-02-01

    Full Text Available 2-Mercaptoethanol self-assembled monolayer (ME/Au SAMs was prepared on a gold electrode. The ME/Au SAMs was characterized by using ATR-FTIR and dynamic contact angle measurements. The electrochemical behaviors of noradrenaline (NE on the ME/Au SAMs were studied in BR buffer solution. The modified electrode accelerated electron transfer rate of the redox of NE and showed an excellent eletrocatalytic activity. The diffusion coefficient (D of NE was obtained to be 4.3×10-8 cm2 s-1. The catalytic current increased linearly with the concentration of NE in the range of 2.0×10-6 -1.0×10-3 M by square wave voltammetry response. The modified electrode could eliminate the interference of ascorbic acid (AA at 40-fold concentration of NE and could be satisfactorily used for the determination of NE in the drug injection.

  7. Modified polyol route for synthesis of Fe{sub 3}O{sub 4}/Ag and α-Fe/Ag nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Abbas, Mohamed [Center for NanoBioEngineering and Spintronics, Department of Materials Science and Engineering, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Department of Emerging Material Science, Daegu Gyeongbuk Institute of Science and Technology (DGIST), Daegu (Korea, Republic of); Ceramics Department, National Research Centre, 12311 Cairo (Egypt); Parvatheeswara Rao, B. [Department of Physics, Andhra University, Visakhapatnam 530003 (India); Abdel-Hamed, M.O. [Physics Department, Faculty of Science, El-Minia University (Egypt); Kim, CheolGi, E-mail: cgkim@cnu.ac.kr [Center for NanoBioEngineering and Spintronics, Department of Materials Science and Engineering, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Department of Emerging Material Science, Daegu Gyeongbuk Institute of Science and Technology (DGIST), Daegu (Korea, Republic of)

    2014-12-05

    Highlights: • We developed new polyol route for synthesis and coating of Fe{sub 3}O{sub 4}/Ag in one-pot. • The phase change from Fe{sub 3}O{sub 4}/Ag to α-Fe/Ag by using the annealing system at 600 °C. • XRD, TEM, EDS, XPS, and VSM techniques used to characterize the samples. • The Fe{sub 3}O{sub 4}/Ag nanocomposite showed nearly superparamagnetic properties. - Abstract: We developed a new one-pot synthesis method for realizing silver coated magnetite nanocomposite by way of a modified polyol process. In this reaction, polyethylene glycol was used as a solvent media and it was observed to play a key role to act as a reducing agent, stabilizer as well as a linker for silver coating simultaneously. Further, we could successfully transfer the phase from Fe{sub 3}O{sub 4}/Ag to α-Fe/Ag by using the annealing system at 600 °C in presence of hydrogen gas. X-ray diffraction data was independently used to confirm the formation of both the phases of Fe{sub 3}O{sub 4}/Ag and α-Fe/Ag. These Fe{sub 3}O{sub 4}/Ag and α-Fe/Ag samples were also characterized using transmission electron microscopy, energy dispersive spectroscopy, and X-ray photoelectron spectroscopy techniques and compared the results with those of seed Fe{sub 3}O{sub 4} nanoparticles. The magnetic properties of the composites, Fe{sub 3}O{sub 4}/Ag and α-Fe/Ag with different Ag concentrations, along with the seed Fe{sub 3}O{sub 4} nanoparticles were measured using vibrating sample magnetometer (VSM) at room temperature. Maximum magnetization values of 61.3 emu/g and 175.1 emu/g were observed for the samples with 1 mL Ag concentrations of Fe{sub 3}O{sub 4}/Ag and α-Fe/Ag, respectively. This new synthesis method looks to be a promising route for facile synthesis of different magnetic nanocomposites suitable for bioapplications.

  8. Preparation and characterization of monodispersed PS/Ag composite microspheres through modified electroless plating

    Energy Technology Data Exchange (ETDEWEB)

    Ma Yuehui [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China); Zhang Qinghua, E-mail: qhzhang@dhu.edu.cn [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China)

    2012-07-15

    A modified electroless silver-plating process has been devised for the preparation of monodispersed, polystyrene/silver (PS/Ag) composite microspheres with tunable shell thickness. Tailoring was achieved by altering the concentration of the silver precursor in the plating bath. PS/Ag composite microspheres were characterized by field-emission scanning electron microscopy, ultraviolet-visible absorption, X-ray diffraction and thermogravimetric analysis. The results showed that a dense, stable and uniform silver nanoshell was formed on the surface of PS microspheres in the presence of poly(vinylpyrrolidone) and glucose. The bulk conductivity of the PS/Ag composites increased from 1.16 S/m to 3.57 Multiplication-Sign 10{sup 4} S/m, corresponding to a shell thickness of 35-198 nm. The PS/Ag composite microspheres with diameters of ca. 3 {mu}m might have great potential to be used as fillers in anisotropic conductive films because of the uniform diameter, low density and good conductivity of the microspheres.

  9. Collagen-chitosan scaffold modified with Au and Ag nanoparticles: Synthesis and structure

    Science.gov (United States)

    Rubina, M. S.; Kamitov, E. E.; Zubavichus, Ya. V.; Peters, G. S.; Naumkin, A. V.; Suzer, S.; Vasil'kov, A. Yu.

    2016-03-01

    Nowadays, the dermal biomimetic scaffolds are widely used in regenerative medicine. Collagen-chitosan scaffold one of these materials possesses antibacterial activity, good compatibility with living tissues and has been already used as a wound-healing material. In this article, collagen-chitosan scaffolds modified with Ag and Au nanoparticles have been synthesized using novel method - the metal-vapor synthesis. The nanocomposite materials are characterized by XPS, TEM, SEM and synchrotron radiation-based X-ray techniques. According to XRD data, the mean size of the nanoparticles (NPs) is 10.5 nm and 20.2 nm in Au-Collagen-Chitosan (Au-CollCh) and Ag-Collagen-Chitosan (Ag-CollCh) scaffolds, respectively in fair agreement with the TEM data. SAXS analysis of the composites reveals an asymmetric size distribution peaked at 10 nm for Au-CollCh and 25 nm for Ag-CollCh indicative of particle's aggregation. According to SEM data, the metal-carrying scaffolds have layered structure and the nanoparticles are rather uniformly distributed on the surface material. XPS data indicate that the metallic nanoparticles are in their unoxidized/neutral states and dominantly stabilized within the chitosan-rich domains.

  10. Characterization and Evaluation of Reverse Osmosis Membranes Modified with Ag2O Nanoparticles to Improve Performance

    Science.gov (United States)

    Al-Hobaib, Abdullah S.; AL-Sheetan, Khalid M.; Shaik, Mohammed Rafi; Al-Andis, Naser M.; Al-Suhybani, M. S.

    2015-09-01

    The objective of this work was to prepare and characterize a new and highly efficient modified membrane by in situ interfacial polymerization on porous polysulfone supports. The process used m-phenylenediamine and trimesoyl chloride in hexane, incorporating silver oxide Ag2O nanoparticles of varied concentrations from 0.001 to 0.1 wt%. Ag2O nanoparticles were prepared at different sizes varying between 20 and 50 nm. The modified membranes were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), atomic force microscopy (AFM), transmission electron microscopy (TEM), and contact angle measurement. The results showed a smooth membrane surface and average surface roughness from 31 to 74 nm. Moreover, hydrophilicity improved and the contact angle decreased to 41° at 0.009 wt% silver oxide. The performances of the developed membranes were investigated by measuring permeate fluxes and salt rejection capability by passing NaCl solutions (2000 ppm) through the membranes at 225 psi. The results showed that the flux increased from 26 to 40.5 L/m2 h, while the salt rejection was high, at 99 %, with 0.003 wt% Ag2O nanoparticles.

  11. Preparation and Characterization of Novel Choline and L-Glutamic Acid Mixed Monolayer Covalently Modified Glassy Carbon Electrode and Its Analytical Application to Nitrite Determination

    Institute of Scientific and Technical Information of China (English)

    晋冠平; 林祥钦

    2005-01-01

    A choline and L-glutamic acid mixed monolayer covalently modified glassy carbon electrode (Ch-Glu/GCE) was fabricated and characterized by X-ray photoelectron spectroscopy (XPS), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). It provided an excellent example of mixed covalent monolayer modification of carbon electrodes with alkanol and amino acid, and also a facile means for altering the interfacial architecture. The Ch-Glu/GCE displayed good catalytic activity toward the oxidation of nitrite anions. Differential pulse voltammetry was used for determination of nitrite at the Ch-Glu/GCE. The Ch-Glu/GCE showed higher capability for restraint of pollutions than a simple Ch modified electrode or a simple Glu modified electrode.

  12. Effects of Oxide-Modified Spherical ZnO on Electrical Properties of Ag/ZnO Electrical Contact Material

    Science.gov (United States)

    Wei, Zhijun; Zhang, Lingjie; Shen, Tao; Qiao, Zhengyang; Yang, Hui; Fan, Xianping; Chen, Lawson

    2016-09-01

    Silver-zinc oxide (Ag/ZnO) electrical contact material is widely used as contacts of the medium duty switching devices. Effects of modified ZnO on properties of Ag/ZnO electrical contact material were investigated in this work. NiO and CuO were introduced to modify spherical ZnO by a chemical solution nano-coating method. Ag/ZnO contacts prepared using the modified spherical ZnO were produced by powder metallurgy (PM) method in a muffle furnace in temperature ranges from 750 to 900 °C. Results show that electrical conductivity, stability of relative density, and Vickers' hardness of Ag/ZnO electrical contact material can be improved by the addition of NiO because of the formation of NiO solid solution Zn0.2Ni0.8O. The addition of CuO to Ag/ZnO electrical contact material makes arcing energy and mass loss lower. Since this is attractive for a longer service life, using NiO and CuO co-modified ZnO as a second phase may be a promising way to improve properties of Ag/ZnO electrical contact material. Hence, the presented results could also be useful for the design of a new Ag/ZnO electrical contact material.

  13. Direct electrochemical oxidation of S-captopril using gold electrodes modified with graphene-AuAg nanocomposites.

    Science.gov (United States)

    Pogacean, Florina; Biris, Alexandru R; Coros, Maria; Lazar, Mihaela Diana; Watanabe, Fumiya; Kannarpady, Ganesh K; Al Said, Said A Farha; Biris, Alexandru S; Pruneanu, Stela

    2014-01-01

    In this paper, we present a novel approach for the electrochemical detection of S-captopril based on graphene AuAg nanostructures used to modify an Au electrode. Multi-layer graphene (Gr) sheets decorated with embedded bimetallic AuAg nanoparticles were successfully synthesized catalytically with methane as the carbon source. The two catalytic systems contained 1.0 wt% Ag and 1.0 wt% Au, while the second had a larger concentration of metals (1.5 wt% Ag and 1.5 wt% Au) and was used for the synthesis of the Gr-AuAg-1 and Gr-AuAg-1.5 multicomponent samples. High-resolution transmission electron microscopy analysis indicated the presence of graphene flakes that had regular shapes (square or rectangular) and dimensions in the tens to hundreds of nanometers. We found that the size of the embedded AuAg nanoparticles varied between 5 and 100 nm, with the majority being smaller than 20 nm. Advanced scanning transmission electron microscopy studies indicated a bimetallic characteristic of the metallic clusters. The resulting Gr-AuAg-1 and Gr-AuAg-1.5 samples were used to modify the surface of commonly used Au substrates and subsequently employed for the direct electrochemical oxidation of S-captopril. By comparing the differential pulse voltammograms recorded with the two modified electrodes at various concentrations of captopril, the peak current was determined to be well-defined, even at relatively low concentration (10(-5) M), for the Au/Gr-AuAg-1.5 electrode. In contrast, the signals recorded with the Au/Gr-AuAg-1 electrode were poorly defined within a 5×10(-6) to 5×10(-3) M concentration range, and many of them overlapped with the background. Such composite materials could find significant applications in nanotechnology, sensing, or nanomedicine.

  14. Sensitive electrochemical sensor of tryptophan based on Ag-C core-shell nanocomposite modified glassy carbon electrode

    Energy Technology Data Exchange (ETDEWEB)

    Mao Shuxian [College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou 215123 (China); Li Weifeng, E-mail: liweifeng@suda.edu.cn [College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou 215123 (China); Long Yumei, E-mail: yumeilong@suda.edu.cn [College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou 215123 (China); Tu Yifeng; Deng, Anping [College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou 215123 (China)

    2012-08-13

    Graphical abstract: Ag-C and Colloidal carbon sphere modified glassy carbon electrodes were prepared. It was clear that the Ag-C/GCE exhibited enhanced electrocatalytic activity towards Trp, which could result from the synergistic effect between Ag core and carbon shell. The Ag-C/GCE showed excellent analytical properties in the determination of Trp. Highlights: Black-Right-Pointing-Pointer The electrochemical behavior of Ag-C core-shell nanocomposite was firstly proposed. Black-Right-Pointing-Pointer Ag-C/GC electrode exhibited favorable electrocatalytic properties towards Trp. Black-Right-Pointing-Pointer The good electrocatalysis was due to the synergistic effect of Ag-core and C-shell. Black-Right-Pointing-Pointer The Ag-C/GC electrode displayed excellent analytical properties in determining Trp. - Abstract: We here reported a simple electrochemical method for the detection of tryptophan (Trp) based on the Ag-C modified glassy carbon (Ag-C/GC) electrode. The Ag-C core-shell structured nanoparticles were synthesized using one-pot hydrothermal method and characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), and Fourier transform-infrared spectroscopy (FTIR). The electrochemical behaviors of Trp on Ag-C/GC electrode were investigated and exhibited a direct electrochemical process. The favorable electrochemical properties of Ag-C/GC electrode were attributed to the synergistic effect of the Ag core and carbon shell. The carbon shell cannot only protect Ag core but also contribute to the enhanced substrate accessibility and Trp-substrate interactions, while nano-Ag core can display good electrocatalytic activity to Trp at the same time. Under the optimum experimental conditions the oxidation peak current was linearly dependent on the Trp concentration in the range of 1.0 Multiplication-Sign 10{sup -7} to 1.0 Multiplication-Sign 10{sup -4} M with a detection limit of 4.0 Multiplication-Sign 10{sup -8} M (S/N = 3). In addition

  15. Development of carbon dots modified fluorescent molecular imprinted Polymer@Ag/AgCl nanoparticle for hepatocellular carcinoma marker

    Science.gov (United States)

    Karfa, Paramita; Madhuri, Rashmi; Sharma, Prashant K.

    2017-05-01

    In this work, a sensitive and selective fluorescent molecularly imprinted polymer (MIP) was developed for detection of hepatocellular carcinoma (HCC) biomarker i.e. alpha feto protein (AFP) using Ag/AgCl as platform. Here, the carbon dots and Ag/AgCl nanoparticles were functionalized with vinyl groups and used as functional monomer for synthesis of AFP-imprinted polymer. The imprinted polymer shows a linear range of 3.96 ng mL-1 to 80.0 ng mL-1 with detection limit of 0.42 ng mL-1.The adsorption property of the MIP@Ag/AgCl was studied and shows the high affinity binding towards their target analyte without any cross-reactivity and false-positive or false-negative results.

  16. Control of indium tin oxide anode work function modified using Langmuir-Blodgett monolayer for high-efficiency organic photovoltaics

    Science.gov (United States)

    Yokokura, Yuya; Dogase, Tomomichi; Shinbo, Tatsuki; Nakayashiki, Yuya; Takagi, Yusuke; Ueda, Kazuyoshi; Sarangerel, Khayankhyarvaa; Delgertsetseg, Byambasuren; Ganzorig, Chimed; Sakomura, Masaru

    2017-08-01

    The use of Langmuir-Blodgett (LB) monolayers to modify the indium tin oxide (ITO) work function and thus improve the performance of zinc phthalocyanine (ZnPc)/fullerene (C60)-based and boron subphthalocyanine chloride (SubPc)/C60-based small molecule organic photovoltaic devices (OPVs) was examined. In general, LB precursor compounds contain one or more long alkyl chain substituents that can act as spacers to prevent electrical contact with adjoining electrode surfaces. As one example of such a compound, arachidic acid (CH3(CH2)18COOH) was inserted in the forms of one-layer, three-layer or five-layer LB films between the anode ITO layer and the p-type layer in ZnPc-C60-based OPVs to investigate the effects of the long alkyl chain group when it acts as an electrically insulating spacer. The short-circuit current density (Jsc) values of the OPVs with the three- and five-layer inserts (1.78 mA.cm-2 and 0.61 mA.cm-2, respectively) were reduced dramatically, whereas the Jsc value for the OPV with the single-layer insertion (2.88 mA.cm-2) was comparable to that of the OPV without any insert (3.14 mA.cm-2). The ITO work function was shifted positively by LB deposition of a surfactant compound, C9F19C2H4-O-C2H4-COOH (PFECA), which contained a fluorinated head group. This positive effect was maintained even after formation of an upper p-type organic layer. The Jsc and open-circuit voltage (Voc) of the SubPc-C60-based OPV with the LB-modified ITO layers were effectively enhanced. As a result, a 42% increase in device efficiency was achieved.

  17. Interactions of doxorubicin with self-assembled monolayer-modified electrodes: electrochemical, surface plasmon resonance (SPR), and gravimetric studies.

    Science.gov (United States)

    Nieciecka, Dorota; Krysinski, Pawel

    2011-02-01

    We present the results on the partitioning of doxorubicin (DOX), a potent anticancer drug, through the model membrane system, self-assembled monolayers (SAMs) on gold electrodes. The monolayers were formed from alkanethiols of comparable length with different ω-terminal groups facing the aqueous electrolyte: the hydrophobic -CH(3) groups for the case of dodecanethiol SAMs or hydrophilic -OH groups of mercaptoundecanol SAMs. The electrochemical experiments combined with the surface plasmon resonance (SPR) and gravimetric studies show that doxorubicin is likely adsorbed onto the surface of hydrophilic monolayer, while for the case of the hydrophobic one the drug mostly penetrates the monolayer moiety. The adsorption of the drug hinders further penetration of doxorubicin into the monolayer moiety.

  18. Hybrid opto-chemical doping in Ag nanoparticle-decorated monolayer graphene grown by chemical vapor deposition probed by Raman spectroscopy

    Science.gov (United States)

    Maiti, R.; Haldar, S.; Majumdar, D.; Singha, A.; Ray, S. K.

    2017-02-01

    The novel opto-chemical doping effect in Ag nanoparticle-decorated monolayer graphene grown by chemical vapor deposition has been investigated using Raman spectroscopy for the first time. We used both noble metal nanoparticles and optical excitation, in a hybrid opto-chemical route, to tune the doping level in graphene. Metal nanoparticle-induced chemical effects and laser power-induced substrate effects alter the doping nature of graphene from p- to n-type. Compared with earlier studies, the proposed method significantly lowers the laser intensity required for optical power-dependent doping, resulting in prevention of damage to the sample due to local heating. Some other interesting observations are the enhanced peak intensity in the Raman spectrum of graphene, enhancement of the D-band intensity and the introduction of G-band splitting. This novel, cheap and easily implemented hybrid optical-chemical doping strategy could be very useful for tuning graphene plasmons on the widely used Si/SiO2 substrates for various photonic device applications.

  19. AgHY分子筛的吸附脱硫性能%Performance of Adsorptive Desulfurization over Modified AgHY Zeolites

    Institute of Scientific and Technical Information of China (English)

    孔祥伦; 邹文芳; 张培青

    2011-01-01

    The AgHY zeolite absorbents with different Ag loadings are prepared by incipient-wetness impregna tion. The physical adsorption analyzer and the X-ray diffraction are employed to characterize these absorbents. The BET results show that the surface areas and pore volumes of AgHY zeolites decrease with an increase in Ag loading. The introduction of Ag lowers the intensities of the XRD peaks of HY zeolite without changing bas ic framework. None of Ag2O peaks appears in the XRD patterns of AgHY zeolites. The removal capability of Ag-modified HY zeolites to dibenzothiophene is investigated by static adsorption. Good performance in dibenzothiophene removal and regeneration is found. 90% DBT can be removed by the Ag10HY ( Ag loading : 10 wt % ) at 60℃ in 2 h. The sulfur content decrease from 330 μg· g-1 to 33 μg· g-1 . Removal Of 89.4 % DBT still can be reached by the used Ag10HY after being calcined at 400℃ in air.%以等体积浸渍法制备不同负载量的AgHY分子筛,利用物理吸附仪和X射线衍射(XRD)技术对分子筛吸附剂进行表征.BET结果表明改性分子筛的比表面积和孔容随Ag的负载量的增加而降低,XRD图谱的变化表明,银的负载仅降低了衍射峰强度,而对HY的骨架结构没有影响,并且也没有Ag2O的特征峰出现.在静态吸附条件下考察了改性AgHY分子筛吸附剂对二苯并噻吩(DBT)的脱除性能.结果表明,Ag改性的HY分子筛具有较好的吸附脱硫性能和再生性能.应用Ag负载量为10%的Ag10HY吸附剂,在吸附时间2h、吸附温度60℃的条件下,二苯并噻吩的脱除率可达90%,硫含量由最初的330μg·g-1降至33 μg·g-1.吸附后的Ag10HY吸附剂在温度400℃、空气介质中再生后,吸附脱除效果仍可达到89.4%.

  20. Electrode modified with a composite film of ZnO nanorods and Ag nanoparticles as a sensor for hydrogen peroxide.

    Science.gov (United States)

    Lin, Chia-Yu; Lai, Yi-Hsuan; Balamurugan, A; Vittal, R; Lin, Chii-Wann; Ho, Kuo-Chuan

    2010-06-30

    A conducting fluorine-doped tin oxide (FTO) electrode, first modified with zinc oxide nanorods (ZnONRs) and subsequently attached with photosynthesized silver nanoparticles (AgNPs), designated as AgNPs/ZnONRs/FTO electrode, was used as an amperometric sensor for the determination of hydrogen peroxide. The first layer (ZnONRs) was obtained by chemical bath deposition (CBD), and was utilized simultaneously as the catalyst for the photoreduction of Ag ions under UV irradiation and as the matrix for the immobilization of AgNPs. The aspect ratio of ZnONRs to be deposited was optimized by controlling the number of their CBDs to render enough surface area for Ag deposition, and the amount of AgNPs to be attached was controlled by adjusting the UV-irradiation time. The immobilized AgNPs showed excellent electrocatalytic response to the reduction of hydrogen peroxide. The resultant amperometric sensor showed 10-fold enhanced sensitivity for the detection of H(2)O(2), compared to that without AgNPs, i.e., only with a layer of ZnONRs. Amperometric determination of H(2)O(2) at -0.55 V gave a limit of detection of 0.9 microM (S/N=3) and a sensitivity of 152.1 mA M(-1) cm(-2) up to 0.983 mM, with a response time (steady-state, t(95)) of 30-40 s. The selectivity of the sensor was investigated against ascorbic acid (AA) and uric acid (UA). Energy dispersive X-ray (EDX) analysis, transmission electron microscopic (TEM) image, X-ray diffraction (XRD) patterns, cyclic voltammetry (CV), and scanning electron microscopic (SEM) images were utilized to characterize the modified electrode. Sensing properties of the modified electrode were studied both by CV and amperometric analysis.

  1. Direct electrochemical oxidation of S-captopril using gold electrodes modified with graphene-AuAg nanocomposites

    Directory of Open Access Journals (Sweden)

    Pogacean F

    2014-02-01

    Full Text Available Florina Pogacean,1 Alexandru R Biris,2 Maria Coros,1 Mihaela Diana Lazar,1 Fumiya Watanabe,3 Ganesh K Kannarpady,3 Said A Farha Al Said,4 Alexandru S Biris,3 Stela Pruneanu1 1Department of Isotopic Physics and Technology, 2Department of Mass Spectrometry, Chromatography, and Applied Physics, National Institute for Research and Development of Isotopic and Molecular Technologies, Cluj-Napoca, Romania; 3Center for Integrative Nanotechnology Sciences, University of Arkansas at Little Rock, Little Rock, Arkansas, USA; 4Department of Physics, College of Science, King Abdulaziz University, Jeddah, Saudi Arabia Abstract: In this paper, we present a novel approach for the electrochemical detection of S-captopril based on graphene AuAg nanostructures used to modify an Au electrode. Multi-layer graphene (Gr sheets decorated with embedded bimetallic AuAg nanoparticles were successfully synthesized catalytically with methane as the carbon source. The two catalytic systems contained 1.0 wt% Ag and 1.0 wt% Au, while the second had a larger concentration of metals (1.5 wt% Ag and 1.5 wt% Au and was used for the synthesis of the Gr-AuAg-1 and Gr-AuAg-1.5 multicomponent samples. High-resolution transmission electron microscopy analysis indicated the presence of graphene flakes that had regular shapes (square or rectangular and dimensions in the tens to hundreds of nanometers. We found that the size of the embedded AuAg nanoparticles varied between 5 and 100 nm, with the majority being smaller than 20 nm. Advanced scanning transmission electron microscopy studies indicated a bimetallic characteristic of the metallic clusters. The resulting Gr-AuAg-1 and Gr-AuAg-1.5 samples were used to modify the surface of commonly used Au substrates and subsequently employed for the direct electrochemical oxidation of S-captopril. By comparing the differential pulse voltammograms recorded with the two modified electrodes at various concentrations of captopril, the peak current

  2. Adsorption and Decomposition of EtO on Cl-modified Ag(111)at Low Temperatures

    Institute of Scientific and Technical Information of China (English)

    吴凯; 王德峥; 魏绪明; 曹玉明; 郭燮贤

    1994-01-01

    The adsorption and decomposition of ethylene oxide(EtO)on Cl-modified and oxygen-pre-covered Ag(111)at low temperatures with high resolution electron energy loss spectroscopy(HREELS)arestudied.At 140 K,EtO is molecularly adsorbed on the surface.At above 230K.with atomic oxygen on thesurface,a small amount of EtO decomposes into ethylene and is oxidized to produce some oxidation productsas water,etc.while with dioxygen on the surface,a large amount of EtO decomposes into ethylene and isoxidized to produce large amounts of oxidation products like water and so on.The experimental resultsshowed that chlorine can,on the one hand,decrease the adsorption amount of EtO and,on the other hand,inhibit the further oxidation of EtO.

  3. Facile synthesis of nano silver ferrite (AgFeO{sub 2}) modified with chitosan applied for biothiol separation

    Energy Technology Data Exchange (ETDEWEB)

    Abdelhamid, Hani Nasser [Department of Chemistry, National Sun Yat-Sen University, Kaohsiung 804, Taiwan (China); Department of Chemistry, Assuit University, Assuit 71515 (Egypt); Wu, Hui-Fen, E-mail: hwu@faculty.nsysu.edu.tw [Department of Chemistry, National Sun Yat-Sen University, Kaohsiung 804, Taiwan (China); School of Pharmacy, College of Pharmacy, Kaohsiung Medical University, Kaohsiung 800, Taiwan (China); Center for Nanoscience and Nanotechnology, National Sun Yat-Sen University, Kaohsiung 804, Taiwan (China); Doctoral Degree Program of Marine Biotechnology, National Sun Yat-Sen University and Academia Sinica, Kaohsiung 804,Taiwan (China); Institute of Medical Science and Technology, National Sun Yat-Sen University, Taiwan (China)

    2014-12-01

    Silver iron oxide nanoparticles (AgFeO{sub 2} NPs) with narrow size distribution have been synthesized, characterized and was applied for biothiols separation. AgFeO{sub 2} and AgFeO{sub 2} modified chitosan (AgFeO{sub 2}@CTS NPs) were synthesized using a hydrothermal method and then characterized by electron microscopy (transmission electron microscopy (TEM), scanning electron microscopy (SEM), and energy dispersive X-ray (EDX)), X-ray diffraction (XRD), and Fourier transform infrared (FTIR). Different biological thiols (dithiothreitol, glutathione, thiabendazole, and sulfamethizole) were investigated and characterized using matrix assisted laser desorption/ionization mass spectrometry (MALDI–MS) and surface assisted laser desorption/ionization mass spectrometry (SALDI–MS). The new material displays dual functionality; 1) for separation and 2) can be served as the matrices for SALDI–MS. Data showed a clear background in the case of nanomaterials compared to conventional matrices (mefenamic acid and 2,5-dihydroxybenzoic acid (DHB) for MALDI–MS). - Highlights: • Facile synthesis of AgFeO{sub 2} and AgFeO{sub 2}@chitosan has been reported • Surface modification of AgFeO{sub 2} with chitosan was presented • Applications for biothiols were investigated using mass spectrometry • Novel application as surface for SALDI-MS were successfully reported.

  4. Determination of Anthracene on Ag-Au Alloy Nanoparticles/Overoxidized-Polypyrrole Composite Modified Glassy Carbon Electrodes

    Science.gov (United States)

    Mailu, Stephen N.; Waryo, Tesfaye T.; Ndangili, Peter M.; Ngece, Fanelwa R.; Baleg, Abd A.; Baker, Priscilla G.; Iwuoha, Emmanuel I.

    2010-01-01

    A novel electrochemical sensor for the detection of anthracene was prepared by modifying a glassy carbon electrode (GCE) with over-oxidized polypyrrole (PPyox) and Ag-Au (1:3) bimetallic nanoparticles (Ag-AuNPs). The composite electrode (PPyox/Ag-AuNPs/GCE) was prepared by potentiodynamic polymerization of pyrrole on GCE followed by its overoxidation in 0.1 M NaOH. Ag-Au bimetallic nanoparticles were chemically prepared by the reduction of AgNO3 and HAuCl4 using C6H5O7Na3 as the reducing agent as well as the capping agent and then immobilized on the surface of the PPyox/GCE. The nanoparticles were characterized by UV-visible spectroscopy technique which confirmed the homogeneous formation of the bimetallic alloy nanoparticles. Transmission electron microscopy showed that the synthesized bimetallic nanoparticles were in the range of 20–50 nm. The electrochemical behaviour of anthracene at the PPyox/Ag-AuNPs/GCE with Ag: Au atomic ratio 25:75 (1:3) exhibited a higher electrocatalytic effect compared to that observed when GCE was modified with each constituent of the composite (i.e., PPyox, Ag-AuNPs) and bare GCE. A linear relationship between anodic current and anthracene concentration was attained over the range of 3.0 × 10−6 to 3.56 × 10−4 M with a detection limit of 1.69 × 10−7 M. The proposed method was simple, less time consuming and showed a high sensitivity. PMID:22163419

  5. Determination of Anthracene on Ag-Au Alloy Nanoparticles/Overoxidized-Polypyrrole Composite Modified Glassy Carbon Electrodes

    Directory of Open Access Journals (Sweden)

    Emmanuel I. Iwuoha

    2010-10-01

    Full Text Available A novel electrochemical sensor for the detection of anthracene was prepared by modifying a glassy carbon electrode (GCE with over-oxidized polypyrrole (PPyox and Ag-Au (1:3 bimetallic nanoparticles (Ag-AuNPs. The composite electrode (PPyox/Ag-AuNPs/GCE was prepared by potentiodynamic polymerization of pyrrole on GCE followed by its overoxidation in 0.1 M NaOH. Ag-Au bimetallic nanoparticles were chemically prepared by the reduction of AgNO3 and HAuCl4 using C6H5O7Na3 as the reducing agent as well as the capping agent and then immobilized on the surface of the PPyox/GCE. The nanoparticles were characterized by UV-visible spectroscopy technique which confirmed the homogeneous formation of the bimetallic alloy nanoparticles. Transmission electron microscopy showed that the synthesized bimetallic nanoparticles were in the range of 20–50 nm. The electrochemical behaviour of anthracene at the PPyox/Ag-AuNPs/GCE with Ag: Au atomic ratio 25:75 (1:3 exhibited a higher electrocatalytic effect compared to that observed when GCE was modified with each constituent of the composite (i.e., PPyox, Ag-AuNPs and bare GCE. A linear relationship between anodic current and anthracene concentration was attained over the range of 3.0 × 10−6 to 3.56 × 10−4 M with a detection limit of 1.69 × 10−7 M. The proposed method was simple, less time consuming and showed a high sensitivity.

  6. Determination of anthracene on Ag-Au alloy nanoparticles/overoxidized-polypyrrole composite modified glassy carbon electrodes.

    Science.gov (United States)

    Mailu, Stephen N; Waryo, Tesfaye T; Ndangili, Peter M; Ngece, Fanelwa R; Baleg, Abd A; Baker, Priscilla G; Iwuoha, Emmanuel I

    2010-01-01

    A novel electrochemical sensor for the detection of anthracene was prepared by modifying a glassy carbon electrode (GCE) with over-oxidized polypyrrole (PPyox) and Ag-Au (1:3) bimetallic nanoparticles (Ag-AuNPs). The composite electrode (PPyox/Ag-AuNPs/GCE) was prepared by potentiodynamic polymerization of pyrrole on GCE followed by its overoxidation in 0.1 M NaOH. Ag-Au bimetallic nanoparticles were chemically prepared by the reduction of AgNO(3) and HAuCl(4) using C(6)H(5)O(7)Na(3) as the reducing agent as well as the capping agent and then immobilized on the surface of the PPyox/GCE. The nanoparticles were characterized by UV-visible spectroscopy technique which confirmed the homogeneous formation of the bimetallic alloy nanoparticles. Transmission electron microscopy showed that the synthesized bimetallic nanoparticles were in the range of 20-50 nm. The electrochemical behaviour of anthracene at the PPyox/Ag-AuNPs/GCE with Ag: Au atomic ratio 25:75 (1:3) exhibited a higher electrocatalytic effect compared to that observed when GCE was modified with each constituent of the composite (i.e., PPyox, Ag-AuNPs) and bare GCE. A linear relationship between anodic current and anthracene concentration was attained over the range of 3.0 × 10(-6) to 3.56 × 10(-4) M with a detection limit of 1.69 × 10(-7) M. The proposed method was simple, less time consuming and showed a high sensitivity.

  7. Phonon dispersion on Ag (100) surface: A modified analytic embedded atom method study

    Science.gov (United States)

    Xiao-Jun, Zhang; Chang-Le, Chen

    2016-01-01

    Within the harmonic approximation, the analytic expression of the dynamical matrix is derived based on the modified analytic embedded atom method (MAEAM) and the dynamics theory of surface lattice. The surface phonon dispersions along three major symmetry directions , and X¯M¯ are calculated for the clean Ag (100) surface by using our derived formulas. We then discuss the polarization and localization of surface modes at points X¯ and M¯ by plotting the squared polarization vectors as a function of the layer index. The phonon frequencies of the surface modes calculated by MAEAM are compared with the available experimental and other theoretical data. It is found that the present results are generally in agreement with the referenced experimental or theoretical results, with a maximum deviation of 10.4%. The agreement shows that the modified analytic embedded atom method is a reasonable many-body potential model to quickly describe the surface lattice vibration. It also lays a significant foundation for studying the surface lattice vibration in other metals. Project supported by the National Natural Science Foundation of China (Grant Nos. 61471301 and 61078057), the Scientific Research Program Funded by Shaanxi Provincial Education Department, China (Grant No. 14JK1301), and the Specialized Research Fund for the Doctoral Program of Higher Education, China (Grant No. 20126102110045).

  8. Posintro™-HBsAg, a modified ISCOM including HBsAg, induces strong cellular and humoral responses

    DEFF Research Database (Denmark)

    Schiött, Asa; Larsson, Kristina; Manniche, Søren;

    2011-01-01

    To improve the hepatitis B vaccines on the market new adjuvant systems have to substitute aluminium. In this study the hepatitis B surface antigen (HBsAg) was incorporated into a novel adjuvant system, the Posintro™, a modification of the traditional immune stimulatory complexes (ISCOMs). This ne...

  9. Voltammetric studies of Azathioprine on the surface of graphite electrode modified with graphene nanosheets decorated with Ag nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Asadian, Elham [Institute for Nanoscience and Nanotechnology (INST), Sharif University of Technology, Tehran (Iran, Islamic Republic of); Iraji zad, Azam [Institute for Nanoscience and Nanotechnology (INST), Sharif University of Technology, Tehran (Iran, Islamic Republic of); Department of Physics, Sharif University of Technology, Tehran 14588-89694 (Iran, Islamic Republic of); Shahrokhian, Saeed, E-mail: shahrokhian@sharif.edu [Institute for Nanoscience and Nanotechnology (INST), Sharif University of Technology, Tehran (Iran, Islamic Republic of); Department of Chemistry, Sharif University of Technology, Tehran 11155-9516 (Iran, Islamic Republic of)

    2016-01-01

    By using graphene nanosheets decorated with Ag nanoparticles (AgNPs-G) as an effective approach for the surface modification of pyrolytic graphite electrode (PGE), a sensing platform was fabricated for the sensitive voltammetric determination of Azathioprine (Aza). The prepared AgNPs-G nanosheets were characterized using transmission electron microscopy (TEM), X-ray diffraction (XRD), UV–vis and Raman spectroscopy techniques. The electrochemical behavior of Aza was investigated by means of cyclic voltammetry. Comparing to the bare PGE, a remarkable enhancement was observed in the response characteristics of Aza on the surface of the modified electrode (AgNPs-G/PGE) as well as a noticeable decrease in its reduction overpotential. These results can be attributed to the incredible enlargement in the microscopic surface area of the electrode due to the presence of graphene nanosheets together with strong adsorption of Aza on its surface. The effect of experimental parameters such as accumulation time, the amount of modifier suspension and pH of the supporting electrolyte were also optimized toward obtaining the maximum sensitivity. Under the optimum conditions, the calibration curve studies demonstrated that the peak current increased linearly with Aza concentrations in the range of 7 × 10{sup −7} to 1 × 10{sup −4} mol L{sup −1} with the detection limit of 68 nM. Further experiments revealed that the modified electrode can be successfully applied for the accurate determination of Aza in pharmaceutical preparations. - Highlights: • A novel electrochemical sensing platform based on graphene nanosheets decorated with Ag nanoparticles was constructed for determination of Azathioprine. • The prepared modified electrode showed an efficient catalytic role toward the electro-reduction of Azathioprine. • The prepared modified electrode shows a wide linear dynamic range and a nanomolar detection limit for Azathioprine. • The modification procedure provides a

  10. Voltammetric Detection of Urea on an Ag-Modified Zeolite-Expanded Graphite-Epoxy Composite Electrode

    Directory of Open Access Journals (Sweden)

    Joop Schoonman

    2008-09-01

    Full Text Available In this paper, a modified expanded graphite composite electrode based on natural zeolitic volcanic tuff modified with silver (EG-Ag-Z-Epoxy was developed. Cyclic voltammetry measurements revealed a reasonably fast electron transfer and a good stability of the electrode in 0.1 M NaOH supporting electrolyte. This modified electrode exhibited moderate electrocatalytic effect towards urea oxidation, allowing its determination in aqueous solution. The linear dependence of the current versus urea concentration was reached using square-wave voltammetry in the concentrations range of urea between 0.2 to 1.4 mM, with a relatively low limit of detection of 0.05 mM. A moderate enhancement of electroanalytical sensitivity for the determination of urea at EG-Ag-Z-Epoxy electrode was reached by applying a chemical preconcentration step prior to voltammetric/amperometric quantification.

  11. Voltammetric studies of Azathioprine on the surface of graphite electrode modified with graphene nanosheets decorated with Ag nanoparticles.

    Science.gov (United States)

    Asadian, Elham; Iraji Zad, Azam; Shahrokhian, Saeed

    2016-01-01

    By using graphene nanosheets decorated with Ag nanoparticles (AgNPs-G) as an effective approach for the surface modification of pyrolytic graphite electrode (PGE), a sensing platform was fabricated for the sensitive voltammetric determination of Azathioprine (Aza). The prepared AgNPs-G nanosheets were characterized using transmission electron microscopy (TEM), X-ray diffraction (XRD), UV-vis and Raman spectroscopy techniques. The electrochemical behavior of Aza was investigated by means of cyclic voltammetry. Comparing to the bare PGE, a remarkable enhancement was observed in the response characteristics of Aza on the surface of the modified electrode (AgNPs-G/PGE) as well as a noticeable decrease in its reduction overpotential. These results can be attributed to the incredible enlargement in the microscopic surface area of the electrode due to the presence of graphene nanosheets together with strong adsorption of Aza on its surface. The effect of experimental parameters such as accumulation time, the amount of modifier suspension and pH of the supporting electrolyte were also optimized toward obtaining the maximum sensitivity. Under the optimum conditions, the calibration curve studies demonstrated that the peak current increased linearly with Aza concentrations in the range of 7 × 10(-7) to 1 × 10(-4)mol L(-1) with the detection limit of 68 nM. Further experiments revealed that the modified electrode can be successfully applied for the accurate determination of Aza in pharmaceutical preparations.

  12. A hydrogen peroxide sensor based on Ag nanoparticles electrodeposited on natural nano-structure attapulgite modified glassy carbon electrode.

    Science.gov (United States)

    Chen, Huihui; Zhang, Zhe; Cai, Dongqing; Zhang, Shengyi; Zhang, Bailin; Tang, Jilin; Wu, Zhengyan

    2011-10-30

    A novel strategy to fabricate hydrogen peroxide (H(2)O(2)) sensor was developed by electrodepositing Ag nanoparticles (NPs) on a glassy carbon electrode modified with natural nano-structure attapulgite (ATP). The result of electrochemical experiments showed that such constructed sensor had a favorable catalytic ability to reduce H(2)O(2). The good catalytic activity of the sensor was ascribed to the ATP that facilitated the formation and homogenous distribution of small Ag NPs. The resulted sensor achieved 95% of the steady-state current within 2s and had a 2.4 μM detection limit of H(2)O(2).

  13. Effect of time and deposition method on quality of phosphonic acid modifier self-assembled monolayers on indium zinc oxide

    Science.gov (United States)

    Sang, Lingzi; Knesting, Kristina M.; Bulusu, Anuradha; Sigdel, Ajaya K.; Giordano, Anthony J.; Marder, Seth R.; Berry, Joseph J.; Graham, Samuel; Ginger, David S.; Pemberton, Jeanne E.

    2016-12-01

    Phosphonic acid (PA) self-assembled monolayers (SAMs) are utilized at critical interfaces between transparent conductive oxides (TCO) and organic active layers in organic photovoltaic devices (OPVs). The effects of PA deposition method and time on the formation of close-packed, high-quality monolayers is investigated here for SAMs fabricated by solution deposition, micro-contact printing, and spray coating. The solution deposition isotherm for pentafluorinated benzylphosphonic acid (F5BnPA) on indium-doped zinc oxide (IZO) is studied using polarization modulation-infrared reflection-absorption spectroscopy (PM-IRRAS) at room temperature as a model PA/IZO system. Fast surface adsorption occurs within the first min; however, well-oriented high-quality SAMs are reached only after ∼48 h, presumably through a continual process of molecular adsorption/desorption and monolayer filling accompanied by molecular reorientation. Two other rapid, soak-free deposition techniques, micro-contact printing and spray coating, are also explored. SAM quality is compared for deposition of phenyl phosphonic acid (PPA), F13-octylphosphonic acid (F13OPA), and pentafluorinated benzyl phosphonic acid (F5BnPA) by solution deposition, micro-contact printing and spray coating using PM-IRRAS. In contrast to micro-contact printing and spray coating techniques, 48-168 h solution deposition at both room temperature and 70 °C result in contamination- and surface etch-free close-packed monolayers with good reproducibility. SAMs fabricated by micro-contact printing and spray coating are much less well ordered.

  14. Effect of Time and Deposition Method on Quality of Phosphonic Acid Modifier Self-Assembled Monolayers on Indium Zinc Oxide

    Energy Technology Data Exchange (ETDEWEB)

    Sang, Lingzi; Knesting, Kristina M.; Bulusu, Anuradha; Sigdel, Ajaya K.; Giordano, Anthony J.; Marder, Seth R.; Berry, Joseph J.; Graham, Samuel; Ginger, David S.; Pemberton, Jeanne E.

    2016-12-15

    Phosphonic acid (PA) self-assembled monolayers (SAMs) are utilized at critical interfaces between transparent conductive oxides (TCO) and organic active layers in organic photovoltaic devices (OPVs). The effects of PA deposition method and time on the formation of close-packed, high-quality monolayers is investigated here for SAMs fabricated by solution deposition, micro-contact printing, and spray coating. The solution deposition isotherm for pentafluorinated benzylphosphonic acid (F5BnPA) on indium-doped zinc oxide (IZO) is studied using polarization modulation-infrared reflection-absorption spectroscopy (PM-IRRAS) at room temperature as a model PA/IZO system. Fast surface adsorption occurs within the first min; however, well-oriented high-quality SAMs are reached only after -48 h, presumably through a continual process of molecular adsorption/desorption and monolayer filling accompanied by molecular reorientation. Two other rapid, soak-free deposition techniques, micro-contact printing and spray coating, are also explored. SAM quality is compared for deposition of phenyl phosphonic acid (PPA), F13-octylphosphonic acid (F13OPA), and pentafluorinated benzyl phosphonic acid (F5BnPA) by solution deposition, micro-contact printing and spray coating using PM-IRRAS. In contrast to micro-contact printing and spray coating techniques, 48-168 h solution deposition at both room temperature and 70 degrees C result in contamination- and surface etch-free close-packed monolayers with good reproducibility. SAMs fabricated by micro-contact printing and spray coating are much less well ordered.

  15. DNA biosensor for detection of Salmonella typhi from blood sample of typhoid fever patient using gold electrode modified by self-assembled monolayers of thiols

    Science.gov (United States)

    Suryapratiwi, Windha Novita; Paat, Vlagia Indira; Gaffar, Shabarni; Hartati, Yeni Wahyuni

    2017-05-01

    Electrochemical biosensors are currently being developed in order to handle various clinical problems in diagnosing infectious diseases caused by pathogenic bacteria, or viruses. On this research, voltammetric DNA biosensor using gold electrode modified by thiols with self-assembled monolayers had been developed to detect a certain sequence of Salmonella typhi DNA from blood sample of typhoid fever patient. Thiol groups of cysteamines (Cys) and aldehyde groups from glutaraldehydes (Glu) were used as a link to increase the performance of gold electrode in detecting guanine oxidation signal of hybridized S. typhi DNA and ssDNA probe. Standard calibration method was used to determine analytical parameters from the measurements. The result shown that, the detection of S. typhi DNA from blood sample of typhoid fever patient can be carried out by voltammetry using gold electrode modified by self-assembled monolayers of thiols. A characteristic oxidation potential of guanine using Au/Cys/Gluwas obtained at +0.17 until +0.20 V. Limit of detection and limit of quantification from this measurements were 1.91μg mL-1 and 6.35 μg mL-1. The concentration of complement DNA from sample was 6.96 μg mL-1.

  16. Highly Efficient and Air Stable Inverted Polymer Solar Cells Using LiF-Modified ITO Cathode and MoO3/AgAl Alloy Anode.

    Science.gov (United States)

    Jia, Xiangkun; Jiang, Ziyao; Chen, Xiaohong; Zhou, Jianping; Pan, Likun; Zhu, Furong; Sun, Zhuo; Huang, Sumei

    2016-02-17

    The performance and air stability of inverted polymer solar cells (PSCs) were greatly improved using a combination of LiF-modified ITO cathode and a MoO3/AgAl alloy anode. The power conversion efficiency (PCE) of PSCs with AgAl contact reached 9.4%, which is higher than that of the cells with Ag (8.8%) and Al electrode (7.6%). The PCE of AgAl-based PSCs can further increase up to 10.3% through incorporating an ultrathin LiF-modified ITO. AgAl-based cells also exhibit a superior stability compared to the cells with Ag and Al contacts. PCE of the AgAl-based cells without encapsulation remains 78% of its original value after the cells were aged for 380 days in air. The presence of a LiF-modified ZnO interlayer between ITO and the organic active layer improves the charge collection. The improvement in PCE and stability of the AgAl-based cells is primarily attributed to the formation of AlOx at the MoO3/AgAl interface, preventing Ag diffusion and improving the built-in potential across the active layer in the cells.

  17. Amperometric detection of Sudan I in red chili powder samples using Ag nanoparticles decorated graphene oxide modified glassy carbon electrode.

    Science.gov (United States)

    Prabakaran, E; Pandian, K

    2015-01-01

    A simple and sensitive electrochemical method was developed to determine the concentration of Sudan I in chili powder based on silver nanoparticles decorated graphene oxide modified glassy carbon electrode (AgNPs@GO/GCE). The voltammetry behaviour of Sudan I on modified GCE was investigated in phosphate buffer medium (PBS) with various pH ranges and the electron transfer properties were studied. It is found that the AgNPs@GO/GCE can catalyse the reduction of azo group, -N=N- followed by electrochemical oxidation of (-)OH group present in Sudan I dye molecule. Quantitative detection of Sudan I present in food products was carried out by amperometry method in which reduction potential was fixed at -0.77 V vs. Ag/AgCl. The amperometry method showed an excellent performance with a sensitivity of 6.83 μA mM(-1) and a detection limit of 11.4 × 10(-7)ML(-1). A linear calibration graph was constructed in the ranging 3.90 × 10(-6) to 3.19 × 10(-5)ML(-1). The method was successfully applied for the determination of Sudan I in red chili powder samples.

  18. Alloy formation during the electrochemical growth of a Ag-Cd ultrathin film on Au(1 1 1)

    Energy Technology Data Exchange (ETDEWEB)

    Barrio, M.C. del; Garcia, S.G. [Instituto de Ingenieria Electroquimica y Corrosion (INIEC), Departamento de Ingenieria Quimica, Universidad Nacional del Sur, Avda. Alem 1253, 8000 Bahia Blanca (Argentina); Salinas, D.R., E-mail: dsalinas@uns.edu.a [Instituto de Ingenieria Electroquimica y Corrosion (INIEC), Departamento de Ingenieria Quimica, Universidad Nacional del Sur, Avda. Alem 1253, 8000 Bahia Blanca (Argentina)

    2009-12-30

    The electrodeposition of a Ag/Cd ultrathin film on a Au(1 1 1) surface and the formation of a surface alloy during this process have been studied using classical electrochemical techniques and in situ Scanning Tunneling Microscopy (STM). The films were obtained from separate electrolytes containing Ag{sup +} or Cd{sup 2+} ions and from a multicomponent solution containing both ions. First, the polarization conditions were adjusted in order to form a Ag film by overpotential deposition. Afterwards, a Cd monolayer was formed onto this Au(1 1 1)/Ag modified surface by underpotential deposition. The voltammetric behavior of the Cd UPD and the in situ STM images indicated that the ultrathin Ag films were uniformly deposited and epitaxially oriented with respect to the Au(1 1 1) surface. Long time polarization experiments showed that a significant Ag-Cd surface alloying accompanied the formation of the Cd monolayer on the Au(1 1 1)/Ag modified surface, independent of the Ag film thickness. In the case of an extremely thin Ag layer (1 Ag ML) the STM images and long time polarization experiments revealed a solid state diffusion process of Cd, Ag, and Au atoms which can be responsible for the formation of different Ag-Cd or Au-Ag-Cd alloy phases.

  19. Enhanced ultraviolet photocatalytic activity of Ag/ZnO nanoparticles synthesized by modified polymer-network gel method

    Science.gov (United States)

    Lu, Y. H.; Xu, M.; Xu, L. X.; Zhang, C. L.; Zhang, Q. P.; Xu, X. N.; Xu, S.; Ostrikov, K.

    2015-09-01

    Ag/ZnO nanoparticle (NP) heterostructures are synthesized through a modified polymer-network gel method in which glucose is added to the precursor solution to prevent the gel from drastically shrinking during drying of the aqueous solution. Structural and optical properties of the samples are characterized by a range of techniques including XRD, SEM, TEM, XPS, UV-Vis, and PL. The high-quality Ag-ZnO heterostructure is evidenced clearly by high-resolution TEM. The Ag/ZnO heterostructure nanocomposites exhibit a higher photocatalytic activity in the degradation of methyl orange than pure ZnO. Especially, Ag/ZnO NP heterostructures with the Ag/Zn molar ratio of 5:95 (sample ZA-5) show the highest degradation efficiency, which is 11 times higher compared with pure ZnO. The photoluminescence properties of the heterostructures and O defect states are studied to well explain the observed photocatalytic effects. ZA-5 also exhibits competitive photocatalytic activity for the degradation of other pollutant dyes such as Methylene blue and Rhodamine B compared with the recently reported techniques, while showing excellent catalyst photostability as well as offering simplicity and reliability.

  20. Enhanced ultraviolet photocatalytic activity of Ag/ZnO nanoparticles synthesized by modified polymer-network gel method

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Y. H.; Xu, M., E-mail: hsuming-2001@aliyun.com [Southwest University for Nationalities, Key Laboratory of Information Materials of Sichuan Province, School of Electrical and Information Engineering (China); Xu, L. X. [Nanyang Technological University, Plasma Sources and Applications Center, NIE (Singapore); Zhang, C. L.; Zhang, Q. P.; Xu, X. N. [Southwest University for Nationalities, Key Laboratory of Information Materials of Sichuan Province, School of Electrical and Information Engineering (China); Xu, S. [Nanyang Technological University, Plasma Sources and Applications Center, NIE (Singapore); Ostrikov, K., E-mail: kostya.ostrikov@qut.edu.au [Queensland University of Technology, Institute for Future Environments and School of Chemistry, Physics, and Mechanical Engineering (Australia)

    2015-09-15

    Ag/ZnO nanoparticle (NP) heterostructures are synthesized through a modified polymer-network gel method in which glucose is added to the precursor solution to prevent the gel from drastically shrinking during drying of the aqueous solution. Structural and optical properties of the samples are characterized by a range of techniques including XRD, SEM, TEM, XPS, UV–Vis, and PL. The high-quality Ag-ZnO heterostructure is evidenced clearly by high-resolution TEM. The Ag/ZnO heterostructure nanocomposites exhibit a higher photocatalytic activity in the degradation of methyl orange than pure ZnO. Especially, Ag/ZnO NP heterostructures with the Ag/Zn molar ratio of 5:95 (sample ZA-5) show the highest degradation efficiency, which is 11 times higher compared with pure ZnO. The photoluminescence properties of the heterostructures and O defect states are studied to well explain the observed photocatalytic effects. ZA-5 also exhibits competitive photocatalytic activity for the degradation of other pollutant dyes such as Methylene blue and Rhodamine B compared with the recently reported techniques, while showing excellent catalyst photostability as well as offering simplicity and reliability.

  1. Ag-Modified In2O3/ZnO Nanobundles with High Formaldehyde Gas-Sensing Performance

    Directory of Open Access Journals (Sweden)

    Fang Fang

    2015-08-01

    Full Text Available Ag-modified In2O3/ZnO bundles with micro/nano porous structures have been designed and synthesized with by hydrothermal method continuing with dehydration process. Each bundle consists of nanoparticles, where nanogaps of 10–30 nm are present between the nanoparticles, leading to a porous structure. This porous structure brings high surface area and fast gas diffusion, enhancing the gas sensitivity. Consequently, the HCHO gas-sensing performance of the Ag-modified In2O3/ZnO bundles have been tested, with the formaldehyde-detection limit of 100 ppb (parts per billion and the response and recover times as short as 6 s and 3 s, respectively, at 300 °C and the detection limit of 100 ppb, response time of 12 s and recover times of 6 s at 100 °C. The HCHO sensing detect limitation matches the health standard limitation on the concentration of formaldehyde for indoor air. Moreover, the strategy to synthesize the nanobundles is just two-step heating and easy to scale up. Therefore, the Ag-modified In2O3/ZnO bundles are ready for industrialization and practical applications.

  2. Enhanced photocatalytic, electrochemical and photoelectrochemical properties of TiO{sub 2} nanotubes arrays modified with Cu, AgCu and Bi nanoparticles obtained via radiolytic reduction

    Energy Technology Data Exchange (ETDEWEB)

    Nischk, Michał [Department of Chemical Technology, Faculty of Chemistry, Gdansk University of Technology, 11/12 G. Narutowicza 11/12 St., 80-233 Gdansk (Poland); Department of Environmental Technology, Faculty of Chemistry, University of Gdansk, 63 Wita Stwosza St., 80-308 Gdansk (Poland); Mazierski, Paweł [Department of Environmental Technology, Faculty of Chemistry, University of Gdansk, 63 Wita Stwosza St., 80-308 Gdansk (Poland); Wei, Zhishun [Institute for Catalysis, Hokkaido University, N21, W10, 001-0021, Sapporo (Japan); Siuzdak, Katarzyna [Centre for Plasma and Laser Engineering, The Szewalski Institute of Fluid-Flow Machinery, Polish Academy of Sciences, 14 Fiszera St., 80-231 Gdansk (Poland); Kouame, Natalie Amoin [Laboratoire de Chimie Physique, CNRS—UMR 8000,Université Paris-Sud, Université Paris-Saclay, Bâtiment 349, 91405 Orsay (France); Kowalska, Ewa [Institute for Catalysis, Hokkaido University, N21, W10, 001-0021, Sapporo (Japan); Remita, Hynd [Laboratoire de Chimie Physique, CNRS—UMR 8000,Université Paris-Sud, Université Paris-Saclay, Bâtiment 349, 91405 Orsay (France); Zaleska-Medynska, Adriana, E-mail: adriana.zaleska@ug.edu.pl [Department of Environmental Technology, Faculty of Chemistry, University of Gdansk, 63 Wita Stwosza St., 80-308 Gdansk (Poland)

    2016-11-30

    Highlights: • TiO{sub 2} nanotubes were modified with Cu, AgCu, Bi nanoparticles via gamma radiolysis. • Excessive amount of deposited metal decreased photocatalytic activity. • AgCu-modified samples were more active than Cu-modified (with the same Cu content). • AgCu nanoparticles exist in a core{sub (Ag)}-shell{sub (Cu)} form. • Examined photocatalysts were resistant towards photocorrosion processes. - Abstract: TiO{sub 2} nanotubes arrays (NTs), obtained via electrochemical anodization of Ti foil, were modified with monometallic (Cu, Bi) and bimetallic (AgCu) nanoparticles. Different amounts of metals’ precursors were deposited on the surface of NTs by the spin-coating technique, and the reduction of metals was performed via gamma radiolysis. Surface modification of titania was studied by EDS and XPS analysis. The results show that AgCu nanoparticles exist in a Ag{sub core}-Cu{sub shell} form. Photocatalytic activity was examined under UV irradiation and phenol was used as a model pollutant of water. Over 95% of phenol degradation was achieved after 60 min of irradiation for almost all examined samples, but only slight difference in degradation efficiency (about 3%) between modified and bare NTs was observed. However, the initial phenol degradation rate and TOC removal efficiency was significantly enhanced for the samples modified with 0.31 and 0.63 mol% of Bi as well as for all the samples modified with Cu and AgCu nanoparticles in comparison with bare titania nanotubes. The saturated photocurrent, under the influence of simulated solar light irradiation, for the most active Bi- and AgCu-modified samples, was over two times higher than for pristine NTs. All the examined materials were resistant towards photocorrosion processes that enables their application for long term processes induced by light.

  3. Growth of Ag nanoparticles using plasma-modified multi-walled carbon nanotubes.

    Science.gov (United States)

    Tseng, Chun-Hao; Chen, Chuh-Yung

    2008-01-23

    This study presents a novel method for preparing multi-walled carbon nanotubes (MWNTs) grafted with a poly(2-hydroxyethyl methacrylate) (HEMA)-silver complex (CNTs-HEMA-Ag complex) through plasma-induced grafting polymerization. The characteristics of the MWNTs after being grafted with HEMA polymer are monitored by Fourier transform infrared (FT-IR) spectroscopy. The chelating groups in the HEMA polymer grafted on the surface of the CNTs-HEMA are the coordination sites for chelating silver ions, and are further used as nanotemplates for the growing of Ag nanoparticles (quantum dots). Transmission electron microscopy (TEM) reveals that the particle size of Ag nanoparticles on the CNT surfaces increases with the Ag(+) chelating concentration, reaction time, and reaction temperature. Moreover, the crystalline phase of Ag nanoparticles is identified by using x-ray diffraction (XRD). In addition, high-resolution x-ray photoelectron spectroscopy (XPS) is used to characterize the functional groups on the surface of the MWNTs after chemical modification through plasma treatment; it demonstrates that the growing amount of the Ag nanoparticles on the nanotubes increases with the Ag(+) chelating concentration due to the blocking effect of the Ag particles forming on the MWNTs.

  4. Antibacterial and microstructure properties of titanium surfaces modified with Ag-incorporated nanotube arrays

    Energy Technology Data Exchange (ETDEWEB)

    Li, Guangzhong; Cheng, Li [State Key Laboratory of Porous Metal Materials, Northwest Institute for Nonferrous Metal Research (China); Yang, Hui-lin [Department of Orthopaedics, Wuxi People' s Hospital, Nanjing Medical University, Jiangsu Province (China); Zhao, Quan-ming, E-mail: abc8385@163.com [Department of Orthopaedics, The First Affiliated Hospital of Soochow University, Suzhou (China)

    2016-07-15

    Although titanium (Ti) and its alloys have been widely used as implants in clinical settings, failures still occur mainly due to poor bioactivity and implant-associated infections. Here, we coated Ti implants with TiO{sub 2} nanotubes (TNTs) incorporated with the antibacterial agent Ag to produce Ag-TNTs, through anodization in AgNO{sub 3} and xenon light irradiation. We characterized surface morphology and composition of the coating with scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. We investigated surface topography of the coatings by atomic force microscopy (AFM) operated in the tapping mode. The results indicate that Ag was successfully doped onto the TNTs, and that the nanoparticles were mainly distributed on the surface of TNTs. Finally, our antibacterial experiments reveal that Ag-TNTs on Ti implants exhibit excellent antibacterial activities, which promises to have significant clinical applications as implants. (author)

  5. Highly Sensitive Aluminium(III) Ion Sensor Based on a Self-assembled Monolayer on a Gold Nanoparticles Modified Screen-printed Carbon Electrode.

    Science.gov (United States)

    See, Wong Pooi; Heng, Lee Yook; Nathan, Sheila

    2015-01-01

    A new approach for the development of a highly sensitive aluminium(III) ion sensor via the preconcentration of aluminium(III) ion with a self-assembled monolayer on a gold nanoparticles modified screen-printed carbon electrode and current mediation by potassium ferricyanide redox behavior during aluminium(III) ion binding has been attempted. A monolayer of mercaptosuccinic acid served as an effective complexation ligand for the preconcentration of trace aluminium; this led to an enhancement of aluminium(III) ion capture and thus improved the sensitivity of the sensor with a detection limit of down to the ppb level. Under the optimum experimental conditions, the sensor exhibited a wide linear dynamic range from 0.041 to 12.4 μM. The lower detection limit of the developed sensor was 0.037 μM (8.90 ppb) using a 10 min preconcentration time. The sensor showed excellent selectivity towards aluminium(III) ion over other interference ions.

  6. Enhancement of photocatalytic and photoelectrocatalytic activity of Ag modified Mpg-C3N4 composites

    Science.gov (United States)

    He, Qiuchen; Zhou, Feng; Zhan, Su; Yang, Yifan; Liu, Yujun; Tian, Yu; Huang, Naibao

    2017-01-01

    In this study, mpg-C3N4/Ag composites of surface plasmon resonance structures were fabricated to improve the photocatalytic and photoelectrocatalytic activities of g-C3N4 via photo-assisted reduction method, which were characterized by XRD, EDS, XPS, FT-IR, FE-SEM, TEM, DRS and BET. The photocatalytic and photoelectrocatalytic activities were evaluated by the degradation of methylene blue (MB) and the oxygen reduction experiment under visible light. The results showed the photocatalytic and photoelectrocatalytic activities were dependent on the weight ratio of Ag and the optimum photocatalytic activity of mpg-C3N4/Ag at a weight ratio of 3% is almost 3 times as high as that of mpg-C3N4. Additionally, mpg-C3N4/Ag exhibited a significantly enhanced oxygen reduction performance under visible light. The limit current density was increased about 2 times by the modification of Ag nanoparticles, compared with that of pristine mpg-C3N4. Finally, based on the first principle, the enhancement mechanism of the photocatalytic and photoelectrocatalytic activities was discussed by the calculation on the band structure and density of states in the mpg-C3N4/Ag composites. The appropriate amount of Ag modification would cause the surface plasmon resonance effect, which improved the photocatalytic, photoelectrocatalytic, and oxygen reduction activities of mpg-C3N4.

  7. Interfacial engineering of self-assembled monolayer modified semi-roll-to-roll planar heterojunction perovskite solar cells on flexible substrates

    DEFF Research Database (Denmark)

    Gu, Zhuowei; Zuo, Lijian; Larsen-Olsen, Thue Trofod

    2015-01-01

    The morphologies of the perovskite (e.g. CH3NH3PbI3) layer are demonstrated to be critically important for highly efficient perovskite solar cells. This work applies 3-aminopropanoic acid as a self-assembled monolayer (C3-SAM) on a poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT......:PSS) hole transport layer (HTL) to modify the crystallinity and coverage of the CH3NH3PbI3 Cl-x(x) film, resulting in a much smoother perovskite surface morphology together with a PCE increase from 9.7% to 11.6%. Since all fabrication steps of these inverted structure devices are carried out under low...

  8. Thermodynamics of the adsorption of organic molecules on graphitized carbon black modified with a monolayer of 5-hydroxy-6-methyluracil

    Science.gov (United States)

    Gus'kov, V. Yu.; Ivanov, S. P.; Shaikhitdinova, Yu. F.; Kudasheva, F. Kh.

    2016-10-01

    Thermodynamic characteristics of the adsorption of alkanes, alcohols, arenes, and esters on graphitized carbon black with a deposited monolayer (0.17%) of 5-hydroxy-6-methyluracil are studied by means of inverse gas chromatography at infinite dilution. It is established that size effects (violation of the additivity of molar changes in internal energy and the entropy of adsorption for pairs of molecules of one homologous series that differ by one methyl group) are observed when organic molecules are adsorbed on the surface of the resulting adsorbent. The size effects are similar to those observed when 1% 5-hydroxy-6-methyluracil is deposited on graphitized carbon black. It is concluded that the observed violation of additivity is associated with cavities in the supramolecular structure.

  9. A study on oxygen reduction inhibition at pyridine-terminated self assembled monolayer modified Au(111) electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Muglali, Mutlu Iskender; Bashir, Asif; Rohwerder, Michael [Max-Planck-Institut fuer Eisenforschung GmbH, Duesseldorf (Germany)

    2010-04-15

    The electroreduction of oxygen on self-assembled monolayers (SAMs) of various pyridinedisulfides and pyridinethiols on Au(111) surfaces has been investigated in alkaline solutions. Electrochemical experiments that were carried out in three-electrode cell reveal a good correlation between the chain-length of thiol molecules and the oxygen reduction inhibition of the resulting adlayer films. The effect of retarded diffusion of oxygen through the protective film has been investigated by forming additional layer of immobilized cytochrome c (cyt.c) metalloprotein on pyridine moiety during linear sweep voltammetry (LSV) scans. At sufficiently negative cathodic potentials the electrochemical reaction rate has been observed to increase together with the density of defects. Morphological changes at different levels of cathodic polarization were investigated by ex situ scanning tunneling microscopy (STM), indicating oxygen reduction reaction (ORR) induced structural defects at the metallorganic interface. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  10. Mediatorless solar energy conversion by covalently bonded thylakoid monolayer on the glassy carbon electrode.

    Science.gov (United States)

    Lee, Jinhwan; Im, Jaekyun; Kim, Sunghyun

    2016-04-01

    Light reactions of photosynthesis that take place in thylakoid membranes found in plants or cyanobacteria are among the most effective ways of utilizing light. Unlike most researches that use photosystem I or photosystem II as conversion units for converting light to electricity, we have developed a simple method in which the thylakoid monolayer was covalently immobilized on the glassy carbon electrode surface. The activity of isolated thylakoid membrane was confirmed by measuring evolving oxygen under illumination. Glassy carbon surfaces were first modified with partial or full monolayers of carboxyphenyl groups by reductive C-C coupling using 4-aminobenzoic acid and aniline and then thylakoid membrane was bioconjugated through the peptide bond between amine residues of thylakoid and carboxyl groups on the surface. Surface properties of modified surfaces were characterized by cyclic voltammetry, contact angle measurements, and electrochemical impedance spectroscopy. Photocurrent of 230 nA cm(-2) was observed when the thylakoid monolayer was formed on the mixed monolayer of 4-carboxylpheny and benzene at applied potential of 0.4V vs. Ag/AgCl. A small photocurrent resulted when the 4-carboxyphenyl full monolayer was used. This work shows the possibility of solar energy conversion by directly employing the whole thylakoid membrane through simple surface modification.

  11. Controllable crystallization and enhanced amorphous stability of Sb-Te films modified by Ag-doping

    Science.gov (United States)

    Zhong, Juechen; Luo, Yang; Gu, Ting; Wang, Zhenglai; Jiang, Kefeng; Wang, Guoxiang; Lu, Yegang

    2016-10-01

    Ag-doped Sb-Te films were deposited by magnetron co-sputtering and the structure, electrical, optical and thermal properties were analyzed. The results show that Ag-doping restrains crystal grain size, and changes a preferred orientation of the crystalline phase. The crystallization temperature is increased due to the Ag addition. Both amorphous resistance and crystalline resistance are enhanced and the resistance ratio reaches ˜104. Compared with Ge2Sb2Te5, Ag26.82(Sb3Te)73.18 film exhibits a better amorphous thermal stability, a higher crystallization temperature (˜166 °C), a wider optical band gap (0.515 eV), a larger crystallization activation energy (3.17 eV) as well as a better 10 years data retention at 92 °C.

  12. Room Temperature Synthesis and Catalytic Properties of Surfactant-Modified Ag Nanoparticles

    OpenAIRE

    Weihua Li; Congtao Sun; Baorong Hou; Xiaodong Zhou

    2012-01-01

    Well-dispersed Ag nanoparticles with size of 20–30 nm were synthesized in water at room temperature with a self-made novel imidazoline Gemini surfactant quaternary ammonium salt of di (2-heptadecyl-1-formyl aminoethyl imidazoline) hexanediamine. Transmission electron microscopy, X-ray powder diffraction, ultraviolet-visible absorption spectra, and Fourier transform infrared ray were used to characterize the Ag nanoparticles. Results showed that the micellized aggregation of imidazoline Gemini...

  13. Interfacial reactions of Sn-Ag-Cu solders modified by minor Zn alloying addition

    Science.gov (United States)

    Kang, Sung K.; Leonard, Donovan; Shih, Da-Yuan; Gignac, Lynne; Henderson, D. W.; Cho, Sungil; Yu, Jin

    2006-03-01

    The near-ternary eutectic Sn-Ag-Cu alloys have been identified as leading Pb-free solder candidates to replace Pb-bearing solders in microelectronic applications. However, recent investigations on the processing behavior and solder joints reliability assessment have revealed several potential reliability risk factors associated with the alloy system. The formation of large Ag3Sn plates in Sn-Ag-Cu joints, especially when solidified in a relatively slow cooling rate, is one issue of concern. The implications of large Ag3Sn plates on solder joint performance and several methods to control them have been discussed in previous studies. The minor Zn addition was found to be effective in reducing the amount of undercooling required for tin solidification and thereby to suppress the formation of large Ag3Sn plates. The Zn addition also caused the changes in the bulk microstructure as well as the interfacial reaction. In this paper, an in-depth characterization of the interfacial reaction of Zn-added Sn-Ag-Cu solders on Cu and Au/Ni(P) surface finishes is reported. The effects of a Zn addition on modification of the interfacial IMCs and their growth kinetics are also discussed.

  14. Controlled synthesis of Fe2O3 modified Ag-010BiVO4 heterostructures with enhanced photoelectrochemical activity toward the dye degradation

    Science.gov (United States)

    Li, Junqi; Zhou, Jian; Hao, Hongjuan; Li, Weijie

    2017-03-01

    Crystal facet dependence is an important approach for optimizing the performance of photocatalyst. In consideration that there is a close correlation between the photoelectric conversion efficiencies and crystal facet, the monoclinic bismuth vanadate (m-BiVO4) with (010) and (110) crystal facets has drawn attention. We designed the Ag nanoparticles modified the (010) facet of the BiVO4 (Ag-010BiVO4) and then the Ag-010BiVO4 heterogeneous nanostructure was modified by the Fe2O3 nanoparticles. In the Fe2O3 modified Ag-010BiVO4, the (110) facet of the BiVO4 was only modified by the Fe2O3 nano-particles to construct the n-n heterojunction structure. Simultaneously, the Z-scheme system was fabricated on the (010) facet of the BiVO4, where was modified by the Ag and Fe2O3 nano-particles. We investigated its photoelectrochemical (PEC) and photocatalytic activities by the measurement of the electrochemical performance and degradation of methyl orange (MO). The Ag species in the system is only treated as the solid state electron mediator. As was expected, the Fe2O3 modified Ag-010BiVO4 heterojunction structure exhibited the highest photocurrent density and the smallest impedance. Besides, the Fe2O3 modified Ag-010BiVO4 heterojunction structure exhibited excellent redox ability and the MO could be degraded 92% after 150 min. It is worth noting that the outstanding performance should be attributed to the synergistic effect of n-n and Z-scheme system in the different facets, which facilitated the separation of holes and electrons in the opposite direction.

  15. Preparation of Ag nanoparticle surface modified TiO2 nanotube arrays and establishment of a catalytic kinetic model

    Science.gov (United States)

    Tang, Hong; Xu, Yingcao; Zhang, Qing

    2017-04-01

    In this paper, the highly ordered TiO2 nanotube arrays were prepared by anodic oxidation method. The electrolyte was composed of ammonium fluoride (0.25 mol/L), glycerol and water (volume ratio 2:1). The anodic oxidation voltage was 25 V, time for two hours. The temperature of calcinations was 450°C, time for four hours. The silver nanoparticles were modified on the surface of TiO2 nanotube arrays by the method of ultrasonic atomization. The experimental results showed that the diameter of TiO2 nanotubes was about 120 nm, the wall thickness was about 12 nm, and the diameter of Ag nanoparticles was about 10 nm, which was more evenly distributed on the pipe diameter. Finally, the catalytic kinetic model of Ag-TiO2 photocatalyst was established based on the Langmuir-Hinshelwood (L-H) model.

  16. Ag-ligand modified tungstovandates and their efficient catalysis degradation properties for methylene blue

    Science.gov (United States)

    Zheng, Ran; Zhang, Huixia; Liu, Yunping; Wang, Xiaoxiao; Han, Zhangang

    2017-02-01

    Two polytungstovandates [Ag(mbpy)2][Ag2(mbpy)3][VW5O19]·H2O (1) and [Ag(mbpy)]2[Ag(mbpy)2]4[VW12O40] (2) (mbpy =4,4‧-dimethyl-2,2‧-bipyridyl), had been hydrothermally synthesized and characterized by IR, TG, and single-crystal X-ray diffraction techniques. Single-crystal structural analysis revealed that the polyanionic clusters in two compounds are different: Lindqvist-type in 1 and α-Keggin-type in 2, respectively, while the cationic moieties in them are Ag-mbpy units. The experiments showed that this kind of hybrid crystal materials possesses more efficiently catalytic performance for the degradation of organic dye methylene blue (MB) in water solution under the UV irradiation. The significant degradation rate of MB can reach 89.9%, 94.9% by crystals 1 and 2 (40 mg) in the course of about 5 min.

  17. Ferroelectric Switching of Vinylidene and Trifluoroethylene Copolymer Thin Films on Au Electrodes Modified with Self-Assembled Monolayers

    Directory of Open Access Journals (Sweden)

    Naoto Tsutsumi

    2014-09-01

    Full Text Available The ferroelectric switching characteristics of a vinylidene fluoride and trifluoroethylene copolymer were significantly changed via the chemical modification of a gold electrode with an alkanethiol self-assembled monolayer (SAM. The alkanethiol SAM-Au electrode successfully suppressed the leakage current (dark current from the electrode to the bulk ferroelectric. Smaller leakage currents led to the formation of an effective electric field in the bulk ferroelectric. At switching cycles ranging from 10 to 100 kHz, significant changes in the ferroelectric properties were observed. At 100 kHz, a remanent polarization (Pr of 68 mC·m−2 was measured, whereas a very small Pr value of 2.4 mC·m−2 was measured for the sample without a SAM. The switching speed of the SAM-Au electrode is as twice as fast as that of the unmodified electrode. A large potential barrier was formed via the insertion of a SAM between the Au electrode and the ferroelectric, effectively changing the ferroelectric switching characteristics.

  18. Changes in the microbiological and chemical characteristics of white bread during storage in paper packages modified with Ag/TiO2-SiO2, Ag/N-TiO2 or Au/TiO2.

    Science.gov (United States)

    Peter, Anca; Mihaly-Cozmuta, Leonard; Mihaly-Cozmuta, Anca; Nicula, Camelia; Ziemkowska, Wanda; Basiak, Dariusz; Danciu, Virginia; Vulpoi, Adriana; Baia, Lucian; Falup, Anca; Craciun, Grigore; Ciric, Alexandru; Begea, Mihaela; Kiss, Claudia; Vatuiu, Daniela

    2016-04-15

    Microbiological and chemical characteristics of white bread during storage in paper-packages modified with Ag/TiO2-SiO2, Ag/N-TiO2 or Au/TiO2 were investigated. The whiteness and the water retention of the modified packages were slightly superior to those exhibited by the reference sample, as the color of the composite was lighter. The water retention was very good especially for the Ag/TiO2-SiO2-paper. These improvements can be associated with the high specific surface area and with the low agglomeration tendency of Ag nanoparticles in comparison with the Au ones. The preservation activity of the composites for the bread storage is positively influenced by photoactivity and presence of nano-Ag. Packages Ag/TiO2-SiO2-paper and Ag/N-TiO2-paper can find their applicability for extending the shelf life of bread by 2 days as compared with the unmodified paper-package. No influence of the Au/TiO2 on the extending the shelf life of bread was observed.

  19. Synthesis of beta-cyclodextrin-modified water-dispersible Ag-TiO2 core-shell nanoparticles and their photocatalytic activity.

    Science.gov (United States)

    Shown, Indrajit; Ujihara, Masaki; Imae, Toyoko

    2011-04-01

    The beta-cyclodextrin-modified Ag-TiO2 core-shell nanoparticles were prepared by sodium borohydrate reduction of AgNO3 and the subsequent hydrolysis of the tetraisopropyl orthotitanate in an aqueous medium. Inversely in the preparation of beta-cyclodextrin-modified TiO2-Ag core-shell nanoparticles, first hydrolysis and then following reduction were carried out. The synthesized spherical core-shell nanoparticles were highly water-dispersible and had an average diameter in the range of 9 to 12 nm. A significant shifting of surface plasmon band was observed for the synthesized Ag-TiO2 and TiO2-Ag core-shell nanoparticles. On a model reaction, namely, the photodegradation of phenol by the UV light irradiation, the photocatalytic property of TiO2 nanoparticles was enhanced, when the Ag nanoparticle was embedded in the core of TiO2 nanoparticles but TiO2 nanoparticles coated by Ag shell decreased the photocatalytic property of TiO2 nanoparticles. The mechanism is ascribed to the surface plasmon characteristics of Ag in the core of the TiO2 nanoparticles under the acceleration by host-guest inclusion characteristics.

  20. Multiple depositions of Ag nanoparticles on chemically modified agarose films for surface-enhanced Raman spectroscopy

    Science.gov (United States)

    Zhai, Wen-Lei; Li, Da-Wei; Qu, Lu-Lu; Fossey, John S.; Long, Yi-Tao

    2011-12-01

    A facile and cost-effective approach for the preparation of a surface-enhanced Raman spectroscopy (SERS) substrate through constructing silver nanoparticle/3-aminopropyltriethoxysilane/agarose films (Ag NPs/APTES/Agar film) on various solid supports is described. The SERS performance of the substrate was systematically investigated, revealing a maximum SERS intensity with four layers of the Ag NP deposition. The enhancement factor of the developed substrate was calculated as 1.5 × 107 using rhodamine 6G (R6G) as the probe molecule, and the reproducibility of the SERS signals was established. A high throughput screening platform was designed, manufactured and implemented which utilised the ability to cast agarose to assemble arrays. Quantitative analysis of 4-aminobenzoic acid (4-ABA) and 4-aminothiophenol (4-ATP) was achieved over a ~0.5 nM-0.1 μM range.A facile and cost-effective approach for the preparation of a surface-enhanced Raman spectroscopy (SERS) substrate through constructing silver nanoparticle/3-aminopropyltriethoxysilane/agarose films (Ag NPs/APTES/Agar film) on various solid supports is described. The SERS performance of the substrate was systematically investigated, revealing a maximum SERS intensity with four layers of the Ag NP deposition. The enhancement factor of the developed substrate was calculated as 1.5 × 107 using rhodamine 6G (R6G) as the probe molecule, and the reproducibility of the SERS signals was established. A high throughput screening platform was designed, manufactured and implemented which utilised the ability to cast agarose to assemble arrays. Quantitative analysis of 4-aminobenzoic acid (4-ABA) and 4-aminothiophenol (4-ATP) was achieved over a ~0.5 nM-0.1 μM range. Electronic supplementary information (ESI) available: the chemical structure of agarose, the SEM characterization of the synthesised Ag NPs, the calculation of the EF, the stability of the SERS substrate. See DOI: 10.1039/c1nr10956a

  1. Electrochemical characteristics of a platinum electrode modified with a matrix of polyvinyl butyral and colloidal Ag containing immobilized horseradish peroxidase.

    Science.gov (United States)

    Yuan, Ruo; Liu, Yan; Li, Qun-Fang; Chai, Ya-Qin; Mo, Chang-Li; Zhong, Xia; Tang, Dian-Ping; Dai, Jian-Yuan

    2005-02-01

    A new hydrogen peroxide biosensor was constructed, which consisted of a platinum electrode modified by a matrix of polyvinyl butyral (PVB) and nanometer-sized Ag colloid containing immobilized horseradish peroxidase (HRP), and using Co(bpy)3(3+) as mediator in the hydrogen peroxide solution. The electrochemical characteristics of the biosensor were studied by cyclic voltammetry and chronoamperometry. The modified process was characterized by electrochemical impedance spectroscopy and cyclic voltammetry. The HRP immobilized on colloidal Ag was stable and retained its biological activity. The sensor displays excellent electrocatalytic response to the reduction of H2O2. Analytical parameters such as pH and temperature were also studied. Linear calibration for H2O2 was obtained in the range of 1x10(-5) to 1x10(-2) M under optimized conditions. The sensor was highly sensitive to H2O2, with a detection limit of 2x10(-6) M, and the sensor achieved 95% of steady-state current within 10 s. The sensor exhibited high sensitivity, selectivity and stability.

  2. Preparation and Characterization of Covalently Binding of Rat Anti-human IgG Monolayer on Thiol-Modified Gold Surface

    Directory of Open Access Journals (Sweden)

    Lv Zhengjian

    2009-01-01

    Full Text Available Abstract The 16-mercaptohexadecanoic acid (MHA film and rat anti-human IgG protein monolayer were fabricated on gold substrates using self-assembled monolayer (SAM method. The surface properties of the bare gold substrate, the MHA film and the protein monolayer were characterized by contact angle measurements, atomic force microscopy (AFM, grazing incidence X-ray diffraction (GIXRD method and X-ray photoelectron spectroscopy, respectively. The contact angles of the MHA film and the protein monolayer were 18° and 12°, respectively, all being hydrophilic. AFM images show dissimilar topographic nanostructures between different surfaces, and the thickness of the MHA film and the protein monolayer was estimated to be 1.51 and 5.53 nm, respectively. The GIXRD 2θ degrees of the MHA film and the protein monolayer ranged from 0° to 15°, significantly smaller than that of the bare gold surface, but the MHA film and the protein monolayer displayed very different profiles and distributions of their diffraction peaks. Moreover, the spectra of binding energy measured from these different surfaces could be well fitted with either Au4f, S2p or N1s, respectively. Taken together, these results indicate that MHA film and protein monolayer were successfully formed with homogeneous surfaces, and thus demonstrate that the SAM method is a reliable technique for fabricating protein monolayer.

  3. A novel Ag+ cation sensor based on polyamidoamine dendrimer modified with 1,8-naphthalimide derivatives

    Science.gov (United States)

    Dodangeh, Mohammad; Gharanjig, Kamaladin; Arami, Mokhtar

    2016-02-01

    In this study, 4-amino-1,8-naphthalimide-conjugated polyamidoamine dendrimer was synthesized and characterized and its potentiality as a cation sensor was investigated. 4-Amino-1,8-naphthalic anhydride reacted with polyamidoamine dendrimer and the product was characterized using FTIR, 1H NMR, 13C NMR and melting point analysis method. The synthesized compound was applied to detect various cations in water media and N,N-dimethylformamide (DMF) via monitoring the quenching of the fluorescence intensity. Furthermore, various metal cations including Cu2 +, Ni2 +, Zn2 +, Pb2 +,Ca2 +, Ba2 +, Cd2 +, Hg2 +, Fe2 +, Fe3 + and Ag+ were tested. The complexes formed between the synthesized compound and metal cations in solution and their effects on Photoinduced Electron Transfer (PET) process were investigated regarding the potential application of the newly-synthesized dendrimer as a colorimetric and fluorescent sensor for such cations. The results clearly confirmed that the 1,8-naphthalimide groups surrounding the central dendrimer core showed strong green fluorescence emission at 553 nm. This effect considerably decreased with the introduction of all cations, except Ag+ where the fluorescence quenching effect was remarkable and more dominant. Therefore, it can be concluded that the synthesized dye has the potentiality of being a highly sensitive and selective fluorescence sensor for Ag+ cation.

  4. AgBr and g-C3N4 co-modified Ag2CO3 photocatalyst: A novel multi-heterostructured photocatalyst with enhanced photocatalytic activity

    Science.gov (United States)

    Tang, Hua; Chang, Shufang; Tang, Guogang; Liang, Wei

    2017-01-01

    Novel and highly efficient visible-light-driven g-C3N4/Ag2CO3/AgBr multi-heterostructured photocatalysts are achieved from the surface modification of g-C3N4/Ag2CO3 with AgBr nanoparticles by a facile and efficient ion-exchange method. The as-prepared g-C3N4/Ag2CO3/AgBr photocatalysts were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), scaning electron microscopy (SEM) and UV-vis diffuse reflectance spectrometry (DRS). Compared with g-C3N4/Ag2CO3, g-C3N4/Ag2CO3/AgBr hybrids exhibit enhanced the degradation activity for typical RhB, MB, and MO dyes under visible light excitation (>420 nm). Photoluminescence (PL), photo-induced current and electrochemical impedance spectroscopy (EIS) results demonstrate the g-C3N4/Ag2CO3/AgBr heterojunctions can effectively suppress the recombination of the generated electron-hole pairs. The higher photocatalytical performance of g-C3N4/Ag2CO3/AgBr can be ascribed to the efficient separation of photogenerated electron-hole pairs due to the formation of multi-heterojunctions, in which the Ag nanoparticles acted as the charge transmission bridge. In addition, the possible transferred and separated behavior of electron-hole pairs and photocatalytic mechanisms based on the experimental results are also proposed in detail.

  5. The development of Ti6Al4V based anti bacterial dental implant modified with TiO2 nanotube arrays doped silver metal (Ag)

    Science.gov (United States)

    Slamet, Bachtiar, B. M.; Wulan, P. P. D. K.; Setiadi, Sari, D. P.

    2017-05-01

    The development of Ti6Al4V based anti bacterial dental implant, modified with dopanted silver metal (Ag) TiO2 nanotube arrays (TiNTAs), is studied in this research. The condition inside the mouth is less foton energy, the dental implant material need to be modified with silver metal (Ag) dopanted TiNTAs. Modified TiNTAs used silver metal dopanted with Photo Assisted Deposition (PAD) method can be used as an electron trapper and produced hydroxyl radical, therefore it has antibacterial properties. The verification of antibacterial properties developed with biofilm static test using Streptococcus mutans bacteria model within 3 and 16 hours incubation, was characterized with XRD and SEM-EDX. Properties test result that resisting the biofilm growth effectively is TiNTAs/Ag/0,15, with 97,62 % disinfection bacteria sampel.

  6. Enhanced photovoltaic performance of QDSSCs via modifying ZnO photoanode with a 3-PPA self-assembled monolayer

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Lili, E-mail: jhyang1@jlnu.edu.cn [Department of Physics, Jilin Normal University, Siping 136000 (China); Key Laboratory of Functional Materials Physics and Chemistry of the Ministry of Education, Jilin Normal University, Siping 136000, Jilin (China); Chen, Gang; Sun, Yunfei [Department of Physics, Jilin Normal University, Siping 136000 (China); Key Laboratory of Functional Materials Physics and Chemistry of the Ministry of Education, Jilin Normal University, Siping 136000, Jilin (China); Han, Donglai; Yang, Shuo [State Key Laboratory of Luminescence and Applications, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Gao, Ming; Wang, Zhe; Zou, Ping; Luan, Hongmei; Kong, Xiangwang; Yang, Jinghai [Department of Physics, Jilin Normal University, Siping 136000 (China); Key Laboratory of Functional Materials Physics and Chemistry of the Ministry of Education, Jilin Normal University, Siping 136000, Jilin (China)

    2015-02-15

    Graphical abstract: - Highlights: • The CdS/3-PPA/ZnO QDSSCs were construct in our experiment. • The power conversion efficiency was strongly enhanced after depositing 3-PPA layer. • The 3-PPA layer serves as a recombination barrier and passivates surface defects. - Abstract: A SAMs layer of 3-PPA with a phosphonic acid headgroup and carboxylic acid tailgroups has been used to modify the surface of ZnO nanorods photoanode in CdS quantum dots sensitized solar cells. Its effects on the photovoltic performance have been investigated in detail by adjusting the concentration and deposition time of 3-PPA. Especially, we utilize ultraviolet photoelectron spectroscopy to characterize the variation of band alignment after introducing 3-PPA layer in the solar cells. The results reveal that the 3-PPA not only suppress the electron-hole recombination process due to its passivation on the surface defects, but forms an energy barrier to efficiently retard the back transfer of electrons, which finally results in the enhancement of conversion efficiency of solar cells.

  7. Water treatment with exceptional virus inactivation using activated carbon modified with silver (Ag) and copper oxide (CuO) nanoparticles.

    Science.gov (United States)

    Shimabuku, Quelen Letícia; Arakawa, Flávia Sayuri; Fernandes Silva, Marcela; Ferri Coldebella, Priscila; Ueda-Nakamura, Tânia; Fagundes-Klen, Márcia Regina; Bergamasco, Rosangela

    2017-08-01

    Continuous flow experiments (450 mL min(-1)) were performed in household filter in order to investigate the removal and/or inactivation of T4 bacteriophage, using granular activated carbon (GAC) modified with silver and/or copper oxide nanoparticles at different concentrations. GAC and modified GAC were characterized by X-ray diffractometry, specific surface area, pore size and volume, pore average diameter, scanning electron microscopy, transmission electron microscopy, zeta potential and atomic absorption spectroscopy. The antiviral activity of the produced porous media was evaluated by passing suspensions of T4 bacteriophage (∼10(5) UFP/mL) through filters. The filtered water was analyzed for the presence of the bacteriophage and the release of silver and copper oxide. The porous media containing silver and copper oxide nanoparticles showed high inactivation capacity, even reaching reductions higher than 3 log. GAC6 (GAC/Ag0.5%Cu1.0%) was effective in the bacteriophage inactivation, reaching 5.53 log reduction. The levels of silver and copper released in filtered water were below the recommended limits (100 ppb for silver and 1000 ppb for copper) in drinking water. From this study, it is possible to conclude that activated carbon modified with silver and copper oxide nanoparticles can be used as a filter for virus removal in the treatment of drinking water.

  8. Dielectric, ferroelectric and impedance spectroscopic studies of Mn and W modified AgNbO{sub 3} ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Muduli, Rakesh; Kumar, Pawan, E-mail: pawankumar@nitrkl.ac.in; Panda, Ranjit Kumar; Panigrahi, Simanchal

    2016-09-01

    In the present study, the effect of heterovalent ion doping on the dielectric and ferroelectric behaviour of AgNbO{sub 3}/AN system was investigated. 0.04 mol of manganese (Mn{sup 4+}) and tungsten (W{sup 6+}) ions of smaller ionic radii were substituted in place of niobium (Nb{sup 5+}) ions in the AN system for generating hole and electron rich compounds, respectively. Better dielectric properties with improved saturation polarisations were observed in the heterovalent ions modified AN ceramics. The relaxation behaviour of the modified AN ceramics was investigated by impedance spectroscopy study and intrinsic grain conduction was found to be dominating in the chosen frequency and temperature ranges. The reduced resistivity of the modified AN ceramics was discussed in terms of calculated activation energy. The significant reduction of the activation energy was proposed as the possible cause of early arrival of relaxation peak in the electron doped AN system. - Highlights: • Holes and electrons doping effect on electrical properties of AN system. • Doping of holes significantly enhanced the ferroelectricity. • Doping of electrons reduced activation energy. • Reduced activation energy was related with grains relaxation process.

  9. Enhanced photocatalytic, electrochemical and photoelectrochemical properties of TiO2 nanotubes arrays modified with Cu, AgCu and Bi nanoparticles obtained via radiolytic reduction

    Science.gov (United States)

    Nischk, Michał; Mazierski, Paweł; Wei, Zhishun; Siuzdak, Katarzyna; Kouame, Natalie Amoin; Kowalska, Ewa; Remita, Hynd; Zaleska-Medynska, Adriana

    2016-11-01

    TiO2 nanotubes arrays (NTs), obtained via electrochemical anodization of Ti foil, were modified with monometallic (Cu, Bi) and bimetallic (AgCu) nanoparticles. Different amounts of metals' precursors were deposited on the surface of NTs by the spin-coating technique, and the reduction of metals was performed via gamma radiolysis. Surface modification of titania was studied by EDS and XPS analysis. The results show that AgCu nanoparticles exist in a Agcore-Cushell form. Photocatalytic activity was examined under UV irradiation and phenol was used as a model pollutant of water. Over 95% of phenol degradation was achieved after 60 min of irradiation for almost all examined samples, but only slight difference in degradation efficiency (about 3%) between modified and bare NTs was observed. However, the initial phenol degradation rate and TOC removal efficiency was significantly enhanced for the samples modified with 0.31 and 0.63 mol% of Bi as well as for all the samples modified with Cu and AgCu nanoparticles in comparison with bare titania nanotubes. The saturated photocurrent, under the influence of simulated solar light irradiation, for the most active Bi- and AgCu-modified samples, was over two times higher than for pristine NTs. All the examined materials were resistant towards photocorrosion processes that enables their application for long term processes induced by light.

  10. Mesquite Gum as a Novel Reducing and Stabilizing Agent for Modified Tollens Synthesis of Highly Concentrated Ag Nanoparticles

    Directory of Open Access Journals (Sweden)

    Maira Berenice Moreno‐Trejo

    2016-10-01

    Full Text Available The synthesis that is described in this study is for the preparation of silver nanoparticles of sizes ranging from 10 nm to 30 nm with a defined shape (globular, confirmed by UV-vis, SEM, STEM and DLS analysis. This simple and favorable one-step modified Tollens reaction does not require any special equipment or other stabilizing or reducing agent except for a solution of purified mesquite gum, and it produces aqueous colloidal dispersions of silver nanoparticles with a stability thatexceeds three months, a relatively narrow size distribution, a low tendency to aggregate and a yield of at least 95% for all cases. Reaction times are between 15 min and 60 min to obtain silver nanoparticles in concentrations ranging from 0.1 g to 3 g of Ag per 100 g of reaction mixture. The proposed synthetic method presents a high potential for scale-up, since its production capacity is rather high and the methodology is simple.The synthesis that is described in this study is for the preparation of silver nanoparticles of sizes ranging from 10 nm to 30 nm with a defined shape (globular, confirmed by UV-vis, SEM, STEM and DLS analysis. This simple and favorable one-step modified Tollens reaction does not require any special equipment or other stabilizing or reducing agent except for a solution of purified mesquite gum, and it produces aqueous colloidal dispersions of silver nanoparticles with a stability thatexceeds three months, a relatively narrow size distribution, a low tendency to aggregate and a yield of at least 95% for all cases. Reaction times are between 15 min and 60 min to obtain silver nanoparticles in concentrations ranging from 0.1 g to 3 g of Ag per 100 g of reaction mixture. The proposed synthetic method presents a high potential for scale-up, since its production capacity is rather high and the methodology is simple.

  11. AC loss in stacks of Bi-2223/Ag tapes modified with ferromagnetic covers at the edges

    Science.gov (United States)

    Safran, S.; Gömöry, F.; Gencer, Ali

    2010-10-01

    We investigated the magnetization loss of stacked Bi-2223/Ag tapes with a ferromagnetic cover on the edges. Such modification has been found recently to reduce the AC loss of a single tape; however, the behavior in a coil winding could be different. With experiments and numerical calculations we show that a ferromagnetic cover on the edges of a superconducting tape could reduce its magnetization loss also when the tapes are arranged in a stack. The effect is weaker for larger numbers of tapes but nevertheless remained significant in a stack of four tapes, which was the maximum number studied here. The effects observed experimentally are nicely explained by the results of numerical calculations.

  12. Structural and electrical properties of microwave processed Ag modified KNN-LS ceramics.

    Science.gov (United States)

    Palei, Prakash; Kumar, Pawan; Agrawal, Dinesh K

    2012-01-01

    Microwave processing steps of 0.95[(K0.5Na0.5)0.94Ag0.06NbO3]-0.05[LiSbO3]/(KNAN-LS) lead free ferroelectric ceramics were optimized for better densification and electrical properties. Calcination temperature and time for single perovskite phase formation were optimized and found to be 850 degrees C for 60 min., respectively. Crystal structural study revealed the presence of mixed structure in the microwave processed (MWP) KNAN-LS ceramics. The sintering of the KNAN-LS ceramics was carried out at 1080 degrees C for 10 min, 20 min and 30 min, respectively, and the sample sintered for 20 min exhibited best properties.

  13. AC loss in stacks of Bi-2223/Ag tapes modified with ferromagnetic covers at the edges

    Energy Technology Data Exchange (ETDEWEB)

    Safran, S; Goemoery, F [Institute of Electrical Engineering, Slovak Academy of Sciences, Dubravska cesta 9, 842 39 Bratislava (Slovakia); Gencer, Ali [Physics Department, Faculty of Sciences, Ankara University, Tandogan, 06100 Ankara (Turkey)

    2010-10-15

    We investigated the magnetization loss of stacked Bi-2223/Ag tapes with a ferromagnetic cover on the edges. Such modification has been found recently to reduce the AC loss of a single tape; however, the behavior in a coil winding could be different. With experiments and numerical calculations we show that a ferromagnetic cover on the edges of a superconducting tape could reduce its magnetization loss also when the tapes are arranged in a stack. The effect is weaker for larger numbers of tapes but nevertheless remained significant in a stack of four tapes, which was the maximum number studied here. The effects observed experimentally are nicely explained by the results of numerical calculations.

  14. Amperometric sensing of anti-HIV drug zidovudine on Ag nanofilm-multiwalled carbon nanotubes modified glassy carbon electrode

    Energy Technology Data Exchange (ETDEWEB)

    Rafati, Amir Abbas, E-mail: aa_rafati@basu.ac.ir; Afraz, Ahmadreza

    2014-06-01

    The zidovudine (ZDV) is the first drug approved for the treatment of HIV virus infection. The detection and determination of this drug are very importance in human serum because of its undesirable effects. A new ZDV sensor was fabricated on the basis of nanocomposite of silver nanofilm (Ag-NF) and multiwalled carbon nanotubes (MWCNTs) immobilized on glassy carbon electrode (GCE). The modified electrodes were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), cyclic voltammetry (CV), and linear sweep voltammetry (LSV) techniques. Results showed that the electrodeposited silver has a nanofilm structure and further electrochemical studies showed that the prepared nanocomposite has high electrocatalytic activity and is appropriate for using in sensors. The amperometric technique under optimal conditions is used for the determination of ZDV ranging from 0.1 to 400 ppm (0.37 μM–1.5 mM) with a low detection limit of 0.04 ppm (0.15 μM) (S/N = 3) and good sensitivity. The prepared sensor possessed accurate and rapid response to ZDV and shows an average recovery of 98.6% in real samples. - Highlights: • New anti-HIV drug sensor was fabricated on the basis of nanomaterials composite. • The GCE modified by prepared hydrophilic MWCNT silver nanoparticles. • Silver nanofilm electrodeposited on MWCNT/GCE and characterized by SEM, EDX, CV and LSV • Response of electrode to ZDV was thoroughly investigated by electrochemical techniques.

  15. A self-cleaning coating based on commercial grade polyacrylic latex modified by TiO{sub 2}/Ag-exchanged-zeolite-A nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Nosrati, Rahimeh, E-mail: ra.nosrati@gmail.com [Polymer Composite Research Laboratory, Department of Applied Chemistry, Faculty of Chemistry, University of Tabriz, Tabriz (Iran, Islamic Republic of); Olad, Ali, E-mail: a.olad@yahoo.com [Polymer Composite Research Laboratory, Department of Applied Chemistry, Faculty of Chemistry, University of Tabriz, Tabriz (Iran, Islamic Republic of); Nofouzi, Katayoon, E-mail: nofouzi@tabrizu.ac.ir [Faculty of Veterinary Medicine, University of Tabriz, Tabriz (Iran, Islamic Republic of)

    2015-08-15

    Graphical abstract: - Highlights: • A novel nanocomposite coating based on polyacrylic was prepared. • Nanostructured TiO{sub 2}/Ag-exchanged-zeolite-A composite material was prepared. • Prepared nanocomposite used as additive for modification of polyacrylic latex. • Modified coatings show self-cleaning and antibacterial properties. • Modified coatings show better stability in water in versus of unmodified polymer. - Abstract: The commercial grade polyacrylic latex was modified in order to prepare a self-cleaning coating. TiO{sub 2}/Ag-exchanged-zeolite-A nanocomposite was prepared and used as additive in the matrix of polyacrylic latex to achieve a hydrophilic and photocatalytic coating. FTIR and UV–visible spectroscopy, X-ray diffraction patterns and FESEM were used to characterize the composition and structure of the nanocomposites and coatings. The acrylic coatings, were prepared by using of TiO{sub 2}/Ag-exchanged-zeolite-A additive, had better UV and visible light absorption, hydrophilic, degradation of organic pollutants, stability in water and antimicrobial properties than pristine commercial grade polyacrylic latex coating. According to the results, the modified polyacrylic based coating containing 0.5 wt% of TiO{sub 2}/Ag-exchanged-zeolite-A nanocomposite additive with TiO{sub 2} to Ag-exchanged-zeolite-A ratio of 1:2 was the best coating considering most of useful properties such as small band gap and low water contact angle. The water contact angle for unmodified polyacrylic latex coating was 68° which was decreased to less than 10° in modified coating after 24 h LED lamp illumination.

  16. Electrochemical degradation of carbamazepine using modified electrode with graphene-AuAg composite

    Science.gov (United States)

    Pogacean, F.; Biris, A. R.; Socaci, C.; Floare-Avram, V.; Rosu, M. C.; Coros, M.; Pruneanu, S.

    2015-12-01

    Carbamazepine is a pharmaceutical drug which has been detected in surface and drinking water primarily due to human usage but also from the accidental disposal of pharmaceuticals into sewers. We have developed a graphene-modified electrode which was tested at the detection and degradation of carbamazepine. The oxidation process was studied by cyclic voltammetry in aqueous and organic solutions. The electrochemical degradation of carbamazepine was performed by polarizing the working electrode at a certain potential, for different times (from 5 to 60 minutes). The degradation efficiency was highly dependent on the type of solution and on the supporting electrolyte.

  17. Preparation of the Ag2O2-PbO2 Modified Electrode and Its Application towards Escherichia coli Fast Counting in Water

    Institute of Scientific and Technical Information of China (English)

    Jing GU; Wen ZHANG; Yu Feng YANG; Lei ZHENG; Zi Rong WU; Li Tong JIN

    2005-01-01

    A novel nano crystalline Ag2O2-PbO2 film chemically modified electrode (CME) was prepared and the CME was characterized by X-ray diffractometer (XRD) and atomic force microscope (AFM). By chronoamperometry, the nano Ag2O2-PbO2 CME was used as bioelectrochemical sensor to determine the population of Escherichia coli (E. coli) in water. Compared with conventional methods, it is found that the technique we used is fast and convenient in counting E.coli.

  18. TiO2 modified with Ag nanoparticles synthesized via ultrasonic atomization-UV reduction and the use of kinetic models to determine the acetic acid photocatalytic degradation

    Science.gov (United States)

    Xu, Yingcao; You, Hong

    2014-12-01

    TiO2 surfaces modified with noble metal nanoparticles have been found to effectively reduce the photogenerated carrier recombination rate and significantly extend the light absorption properties of TiO2, thereby greatly increasing its photocatalytic activity. In this paper, highly ordered, double-sided TiO2 nanotube arrays were prepared using an anodic oxidation method in a home-made reactor using glycerol/water (volume ratio 2:1) and NH4F (0.25 mol/L) as the electrolyte, titanium plates (10 cm × 2 cm × 0.5 mm) as the anode and graphite as the cathode at a constant voltage of 25 V. After a 2-h reaction, anatase TiO2 nanotubes were obtained upon calcination at 450 °C for 4 h. The Ag nanoparticles on the surfaces of the TiO2 were prepared via ultrasonic atomization-ultraviolet light reduction. First, a silver nitrate solution was sputtered into small droplets under ultrasonication. Then, the Ag+ droplets were reduced to Ag nanoparticles. The surface morphologies, structures and elemental compositions were characterized using SEM, EDS, XRD and XPS. The photocatalytic activities were determined in acetic acid solutions (40-200 mg/L), and a mathematical model for catalytic degradation was established based on a hyperbolic model. The SEM results showed that the diameters of the as-prepared Ag/TiO2 are approximately 100 nm and that the lengths are approximately 1.8 μm. The XRD crystal structure analysis shows that the anatase phase of the TiO2 does not change during the Ag modification, and there was a peak from Ag (2 2 0). The XPS determined that the Ag atom percentage was 1.11%. The degradation of acetic acid indicated that Ag/TiO2 has a higher photocatalytic activity than the undoped TiO2.

  19. Recombinant modified vaccinia virus Ankara expressing glycoprotein E2 of Chikungunya virus protects AG129 mice against lethal challenge.

    Directory of Open Access Journals (Sweden)

    Petra van den Doel

    2014-09-01

    Full Text Available Chikungunya virus (CHIKV infection is characterized by rash, acute high fever, chills, headache, nausea, photophobia, vomiting, and severe polyarthralgia. There is evidence that arthralgia can persist for years and result in long-term discomfort. Neurologic disease with fatal outcome has been documented, although at low incidences. The CHIKV RNA genome encodes five structural proteins (C, E1, E2, E3 and 6K. The E1 spike protein drives the fusion process within the cytoplasm, while the E2 protein is believed to interact with cellular receptors and therefore most probably constitutes the target of neutralizing antibodies. We have constructed recombinant Modified Vaccinia Ankara (MVA expressing E3E2, 6KE1, or the entire CHIKV envelope polyprotein cassette E3E26KE1. MVA is an appropriate platform because of its demonstrated clinical safety and its suitability for expression of various heterologous proteins. After completing the immunization scheme, animals were challenged with CHIV-S27. Immunization of AG129 mice with MVAs expressing E2 or E3E26KE1 elicited neutralizing antibodies in all animals and provided 100% protection against lethal disease. In contrast, 75% of the animals immunized with 6KE1 were protected against lethal infection. In conclusion, MVA expressing the glycoprotein E2 of CHIKV represents as an immunogenic and effective candidate vaccine against CHIKV infections.

  20. Photoelectrical properties of Ag2S quantum dot-modified TiO2 nanorod arrays and their application for photovoltaic devices.

    Science.gov (United States)

    Liu, Bingkun; Wang, Dejun; Zhang, Yu; Fan, Haimei; Lin, Yanhong; Jiang, Tengfei; Xie, Tengfeng

    2013-02-14

    Vertically aligned TiO(2) nanorod arrays (NRAs) modified with Ag(2)S quantum dots (QDs) have been successfully prepared via a successive ionic layer adsorption and reaction (SILAR) process. Ultraviolet-visible (UV-vis) absorption spectra and surface photovoltage (SPV) measurements reveal that the Ag(2)S sensitization extends the range of the photoresponse of the TiO(2) NRAs to the visible region and exhibits higher photovoltage responses. With a polysulfide electrolyte, a maximum conversion efficiency of 0.148% with a superior J(sc) of 1.177 mA cm(-2) are obtained after 6 SILAR cycles under illumination at 100 mW cm(-2). These results indicate that the Ag(2)S QDs/TiO(2) NRAs photoelectrode has a promising application in solar cells.

  1. Photoelectrochemical detection of alpha-fetoprotein based on ZnO inverse opals structure electrodes modified by Ag2S nanoparticles

    Science.gov (United States)

    Jiang, Yandong; Liu, Dali; Yang, Yudan; Xu, Ru; Zhang, Tianxiang; Sheng, Kuang; Song, Hongwei

    2016-01-01

    In this work, a new photoelectrochemical biosensor based on Ag2S nanoparticles (NPs) modified macroporous ZnO inverse opals structure (IOs) was developed for sensitive and rapid detection of alpha fetal protein (AFP). Small size and uniformly dispersed Ag2S NPs were prepared using the Successive Ionic Layer Adsorption And Reaction (SILAR) method, which were adsorbed on ZnO IOs surface and frame work as matrix for immobilization of AFP. The composite structure of ZnO/Ag2S expanded the scope of light absorption to long wavelength, which can make full use of the light energy. Meanwhile, an effective matching of energy levels between the conduction bands of Ag2S and ZnO are beneficial to the photo-generated electrons transfer. The biosensors based on FTO (fluorine-doped tinoxide) ZnO/Ag2S electrode showed enough sensitivity and a wide linear range from 0.05 ng/mL to 200 ng/mL with a low detection limit of 8 pg/mL for the detection of AFP. It also exhibited high reproducibility, specificity and stability. The proposed method was potentially attractive for achieving excellent photoelectrochemical biosensor for detection of other proteins. PMID:27922086

  2. Improved electrochemical performance of Ag-modified Li4Ti5O12 anode material in a broad voltage window

    Indian Academy of Sciences (India)

    Yan-Rong Zhu; Ting-Feng Yi; Hong-Tao Ma; Yong-Quan Ma; Li-Juan Jiang; Rong-Sun Zhu

    2014-01-01

    Li4Ti5O12/Ag composites were synthesized by a solid-state method. The effect of Ag modification on the physical and electrochemical properties is discussed by the characterizations of X-ray diffraction, scanning electron microscopy, cyclic voltammetry, electrochemical impedance spectroscopy, cycling and rate tests. The lattice parameter of Li4Ti5O12 with a low Ag content is almost not changed, but the lattice parameter becomes larger due to the high content of Ag. Li4Ti5O12/Ag material has a uniform particle size which is about 1 m. Modification of appropriate Ag is beneficial to the reversible intercalation and deintercalation of Li+. Modification of Ag not only decreases the charge transfer resistance of Li4Ti5O12 material, but also improves the diffusion coefficient of lithium ion. Li4Ti5O12/Ag (3 mass%) material has the lowest charge transfer resistance, the highest diffusion coefficient of lithium ion and the best rate cycling performance.

  3. Synthesis and characterization of graphene oxide modified AgBr nanocomposites with enhanced photocatalytic activity and stability under visible light

    Science.gov (United States)

    Zhang, Du; Tang, Hua; Wang, Yuqi; Wu, Kongqiang; Huang, Hong; Tang, Guogang; Yang, Jin

    2014-11-01

    Novel visible-light-driven graphene oxide (GO)/AgBr nanocomposites were synthesized by a facile solution method. The GO/AgBr nanocomposites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoemission spectroscopy (XPS) analysis, UV-vis diffuse reflectance spectroscopy (DRS), Fourier transform infrared spectra (FTIR), and Raman spectra. The results indicated that AgBr nanoparticles were evenly distributed on the surface of GO and the heterostructures were formed. The photocatalytic activity of the as-prepared nanocomposites was evaluated by using Rhodamine B (RhB), Methylene blue (MB) and Methyl orange (MO) as target organic pollutants. The nanocomposites exhibit excellent photocatalytic activity for all of three dyes. Compared with bare AgBr particles, the GO/AgBr nanocomposites show better photocatalytic properties toward RhB pollutants. Additionally, the radical scavengers experiment indicated that O2rad - radicals was the main reactive species for the RhB degradation under visible light. The increased photocatalytic activity of the GO/AgBr nanocomposites was attributed to the strong coupling between GO and AgBr, which facilitated interfacial charge transfer and inhibited electron-hole recombination. A photocatalytic mechanism of GO/AgBr nanocomposites was also proposed.

  4. A study of the antibacterial efficiency and coloration of dyed polyamide and polyester fabrics modified with colloidal Ag nanoparticles

    Directory of Open Access Journals (Sweden)

    VESNA ILIĆ

    2009-03-01

    Full Text Available In this study, the influence of dyeing on the antibacterial efficiency of polyamide and polyester fabrics loaded with colloidal Ag nanoparticles and the influence of the presence of Ag nanoparticles on the color change of dyed fabrics were investigated. Dyes C.I. acid green 25 and C.I. disperse blue 3 were used for dyeing of polyamide fabrics, while dye C.I. disperse violet 8 was used for dyeing of polyester fabrics. The influence of Ag nanoparticles on the color change of polyamide fabrics depends on the dye type, but generally it was lower compared to polyester fabrics. Polyester fabrics exhibited excellent antibacterial efficiency against Gram-positive bacterium Staphylococcus aureus and Gram-negative bacterium Escherichia coli, independent of the order of dyeing and Ag loading. Polyamide fabrics provided a desirable level of antibacterial activity only if the Ag loading was performed after dyeing.

  5. Photochemical synthesis, characterization and enhanced visible light induced photocatalysis of Ag modified TiO2 nanocatalyst.

    Science.gov (United States)

    Ko, Seonghyuk

    2014-09-01

    Nanocomposite of titania (TiO2) and silver (Ag) has been synthesized by a photochemical deposition method. We investigated the simultaneous enhancement of visible light sensitivity and photocatalytic activities of as-prepared Ag-TiO2 nanocomposite photocatalyst. The resulting Ag-TiO2 nanomaterials were characterized by various analytical techniques including X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), UV-Vis diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS) and photoluminescence (PL). Photocatalytic activity was evaluated by decomposition of methylene blue (MB) dye solution under simulated visible light irradiation. Ag nanoparticles were well dispersed on the surface of TiO2 and composite nanoparticles were effectively enhanced in visible light-induced photocatalytic activity compared to that of Ag free TiO2. It was found that the enhanced activity is result from simultaneous effects of nano-Ag deposits by increasing the absorption capacity in visible region and by acting as electron trappers to promote charge separation of photoinduced electrons (e-) and holes (h+). The effect of the amount of Ag nanoparticles on its photoactivity under simulated visible light was also investigated.

  6. Synthesis and characterization of graphene oxide modified AgBr nanocomposites with enhanced photocatalytic activity and stability under visible light

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Du [School of Materials Science and Engineering, Jiangsu University, Zhenjiang, Jiangsu 212013 (China); Tang, Hua, E-mail: tanghua@mail.ujs.edu.cn [School of Materials Science and Engineering, Jiangsu University, Zhenjiang, Jiangsu 212013 (China); Wang, Yuqi; Wu, Kongqiang; Huang, Hong [School of Materials Science and Engineering, Jiangsu University, Zhenjiang, Jiangsu 212013 (China); Tang, Guogang [Department of Chemical Engineering, Zhenjiang College, Zhenjiang, Jiangsu 212003 (China); Yang, Jin [School of Materials Science and Engineering, Jiangsu University, Zhenjiang, Jiangsu 212013 (China)

    2014-11-15

    Highlights: • GO/AgBr nanocomposites were prepared successfully. • There exists some synergistic effect between components in the composites. • The composites show high photocatalytic activity toward RhB, MB and MO degradation under visible light. - Abstract: Novel visible-light-driven graphene oxide (GO)/AgBr nanocomposites were synthesized by a facile solution method. The GO/AgBr nanocomposites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoemission spectroscopy (XPS) analysis, UV–vis diffuse reflectance spectroscopy (DRS), Fourier transform infrared spectra (FTIR), and Raman spectra. The results indicated that AgBr nanoparticles were evenly distributed on the surface of GO and the heterostructures were formed. The photocatalytic activity of the as-prepared nanocomposites was evaluated by using Rhodamine B (RhB), Methylene blue (MB) and Methyl orange (MO) as target organic pollutants. The nanocomposites exhibit excellent photocatalytic activity for all of three dyes. Compared with bare AgBr particles, the GO/AgBr nanocomposites show better photocatalytic properties toward RhB pollutants. Additionally, the radical scavengers experiment indicated that O{sub 2}·{sup −} radicals was the main reactive species for the RhB degradation under visible light. The increased photocatalytic activity of the GO/AgBr nanocomposites was attributed to the strong coupling between GO and AgBr, which facilitated interfacial charge transfer and inhibited electron-hole recombination. A photocatalytic mechanism of GO/AgBr nanocomposites was also proposed.

  7. TiO2/Ag modified penta-bismuth hepta-oxide nitrate and its adsorption performance for azo dye removal

    Institute of Scientific and Technical Information of China (English)

    Eshraq Ahmed Abdullah; Abdul Halim Abdullah; Zulkarnain Zainal; Mohd Zobir Hussein; Tan Kar Ban

    2012-01-01

    A modified hydrophilic penta-bismuth hepta-oxide nitrate (Bi5O7NO3) surface was synthesized via a precipitation method using TiO2 and Ag as modified agents.The synthesized product was characterized by different analytical techniques.The removal efficiency was evaluated using mono- and di-sulphonated azo dyes as model pollutants.Different kinetic,isotherm and diffusion models were chosen to describe the adsorption process.X-ray photoelectron spectroscopy (XPS) results revealed no noticeable differences in the chemical states of modified adsorbent when compared to pure Bi5O7NO3; however,the presence of hydrophilic centres such as TiO2 and Ag developed positively charged surface groups and improved its adsorption performance to a wide range of azo dyes.Dyes removal was found to be a function of adsorbent dosage,initial dye concentration,solution pH and temperature.The reduction of Langrnuir 1,2-mixed order kinetics to the second or first-order kinetics could be successfully used to describe the adsorption of dyes onto the modified adsorbent.Mass transfer can be described by intra-particle diffusion at a certain stage,but it was not the rate limiting step that controlled the adsorption process.Homogenous behavior of adsorbent surface can be explored by applying Langmuir isotherm to fit the adsorption data.

  8. Detection of H2O2 at a composite film modified electrode with highly dispersed Ag nanoparticles in Nafion

    Institute of Scientific and Technical Information of China (English)

    Mei Xiu Kan; Xue Ji Wang; Hui Min Zhang

    2011-01-01

    Ag nanoparticles were prepared by using the ion-exchange of Nafion combined with electrochemical reduction on the electrode. Ag nanoparticles are highly dispersed in Nafion film with an average size of 4.0 ± 0.2 nm. The amount of Ag nanoparticles can be readily controlled by the amount of Nafion coated on the electrode. Thus obtained Ag nanoparticles exhibit good catalytic activity for the reduction of H2O2 with a linear response to H2O2 in the concentration range of 0.04-8.0 mmol/L with a sensitivity of 0.34 μA/mmol/L and a detection limit of 1.0×10-8 mol/L.

  9. Improved performance of Ag-doped TiO2 synthesized by modified sol-gel method as photoanode of dye-sensitized solar cell

    Science.gov (United States)

    Gupta, Arun Kumar; Srivastava, Pankaj; Bahadur, Lal

    2016-08-01

    Ag-doped TiO2 with Ag content ranging from 1 to 7 mol% was synthesized by a modified sol-gel route, and its performance as the photoanode of dye-sensitized solar cells (DSSCs) was compared with undoped TiO2 photoanode. Titanium(IV)isopropoxide was used as precursor and hexamethylenetetramine as the capping agent. XRD results show the formation of TiO2 nanoparticles with an average crystallite size of 5 nm (1 % Ag-doped TiO2) and 9 nm (undoped TiO2), respectively. The TiO2 nanopowder was used to prepare its thin film photoelectrode using doctor's blade method. Significant improvement in light-to-energy conversion efficiency was achieved when thin films of 1 % Ag-doped TiO2 were applied as photoanode in DSSC taking N719 as the sensitizer dye. As evidenced by EIS measurements, the electron lifetime of DSSC with Ag-doped TiO2 increased from 1.33 (for undoped TiO2) to 2.05 ms. The short-circuit current density ( J sc), open-circuit voltage ( V oc), fill factor (FF) and the overall energy conversion efficiency ( η) were 1.07 mA cm-2, 0.72 V, 0.73 and 0.40 %, respectively, with the use of 1 % Ag-doped TiO2 photoanode, whereas with undoped TiO2 under similar conditions, J sc = 0.63 mA cm-2, V oc = 0.70 V, fill factor 0.45 and conversion efficiency 0.14 % could be obtained. Therefore, compared with the reference DSSC containing an undoped TiO2 photoanode, the power conversion efficiency of the cell based on Ag-doped TiO2 has been remarkably enhanced by ~70 %. The substantial improvement in the device performance is attributed to the reduced band-gap energy, retarded charge recombination and greater surface coverage of the sensitizing dye over Ag-doped TiO2, which ultimately resulted in improved IPCE, J SC and η values.

  10. Photo-reduction of bromate in drinking water by metallic Ag and reduced graphene oxide (RGO) jointly modified BiVO4 under visible light irradiation.

    Science.gov (United States)

    Chen, Fei; Yang, Qi; Zhong, Yu; An, Hongxue; Zhao, Jianwei; Xie, Ting; Xu, Qiuxiang; Li, Xiaoming; Wang, Dongbo; Zeng, Guangming

    2016-09-15

    Bromate (BrO3(-)), an oxyhalide disinfection by-product (DBP) in drinking water, has been demonstrated to be carcinogenic and genotoxic. In the current work, metallic Ag and reduced graphene oxide (RGO) co-modified BiVO4 was successfully synthesized by a stepwise chemical method coupling with a photo-deposition process and applied in the photo-reduction of BrO3(-) under visible light irradiation. In this composite, metallic Ag acted as an electron donor or mediator and RGO enhanced the BrO3(-) adsorption onto the surface of catalysts as well as an electron acceptor to restrict the recombination of photo-generated electron-hole pairs. The Ag@BiVO4@RGO composite exhibited greater photo-reduction BrO3(-) performance than pure BiVO4, Ag@BiVO4 and RGO@BiVO4 under identical experimental conditions: initial BrO3(-) concentration 150 μg/L, catalyst dosage 0.5 g/L, pH 7.0 and visible light (λ > 420 nm). The photoluminescence spectra (PL), electron-spin resonance (ESR), photocurrent density (PC) and electrochemical impedance spectroscopy (EIS) measurements indicated that the modified BiVO4 enhanced the photo-generated electrons and separated the electron-hole pairs. The photocatalytic reduction efficiency for BrO3(-) removal decreased with the addition of electron quencher K2S2O8, suggesting that electrons were the primary factor in this photo-reduction process. The declining photo-reduction efficiency of BrO3(-) in tap water should attribute to the consumption of photo-generated electrons by coexisting anions and the adsorption of dissolved organic matter (DOM) on graphene surface. The overall results indicate a promising application potential for photo-reduction in the DBPs removal from drinking water.

  11. Extracellular polymeric substances (EPS of freshwater biofilms stabilize and modify CeO2 and Ag nanoparticles.

    Directory of Open Access Journals (Sweden)

    Alexandra Kroll

    Full Text Available Streams are potential receiving compartments for engineered nanoparticles (NP. In streams, NP may remain dispersed or settle to the benthic compartment. Both dispersed and settling NP can accumulate in benthic biofilms called periphyton that are essential to stream ecosystems. Periphytic organisms excrete extracellular polymeric substances (EPS that interact with any material reaching the biofilms. To understand the interaction of NP with periphyton it is therefore crucial to study the interaction of NP with EPS. We investigated the influence of EPS on the physicochemical properties of selected NP (CeO2, Ag under controlled conditions at pH 6, 7.6, 8.6 and light or dark exposure. We extracted EPS from five different periphyton communities, characterized the extracts, and exposed CeO2 and carbonate-stabilized Ag NP (0.5 and 5 mg/L, both 25 nm primary particle size and AgNO3 to EPS (10 mg/L over two weeks. We measured NP size distribution, shape, primary particle size, surface plasmon resonance, and dissolution. All EPS extracts were composed of biopolymers, building blocks of humic substances, low molecular weight (Mr acids, and small amphiphilic or neutral compounds in varying concentrations. CeO2 NP were stabilized by EPS independent of pH and light/dark while dissolution increased over time in the dark at pH 6. EPS induced a size increase in Ag NP in the light with decreasing pH and the formation of metallic Ag NP from AgNO3 at the same conditions via EPS-enhanced photoreduction. NP transformation and formation were slower in the extract with the lowest biopolymer and low Mr acid concentrations. Periphytic EPS in combination with naturally varying pH and light/dark conditions influence the properties of the Ag and CeO2 NP tested and thus the exposure conditions within biofilms. Our results indicate that periphytic organisms may be exposed to a constantly changing mixture of engineered and naturally formed Ag NP and Ag+.

  12. Removal of carbonyl sulfide from CO2 stream using AgNO3-modified NaZSM-5

    Institute of Scientific and Technical Information of China (English)

    Yanjun; Wang; Shaoyun; Chen; Heng; Chen; Xingzhou; Yuan; Yongchun; Zhang

    2013-01-01

    Removal of carbonyl sulfide(COS) from CO2 stream is significant for the production and utilization of food grade CO2. This study investigates the adsorption performance of Ag/NaZSM-5 as adsorbent prepared by incipient wetness impregnation for the removal of COS from a CO2 stream in a fixed-bed adsorption apparatus. Effects of various conditions on the preparation of adsorbent, adsorption and desorption were intensively examined. The results revealed that COS can be removed to below 1×10-9from a CO2stream(1000 ppm COS/CO2) using Ag/NaZSM-5(10 wt% AgNO3) with an adsorption capacity of 12.86 mg·g-1. The adsorbent can be fully regenerated using hot air at 450 C. The adsorption ability remained stable even after eight cycles of regeneration.

  13. Experimental research on key performance of modified AG8 0/DDS/PEK epoxy resin%AG80/DDS/PEK树脂改性体系的关键性能研究

    Institute of Scientific and Technical Information of China (English)

    朱文韬; 朱波; 曹伟伟; 龙国荣; 韩荣桓; 李永威

    2014-01-01

    以4,4’-二氨基二苯甲烷(AG80)为基体树脂,以4,4’-二氨基二苯砜(DDS)为固化剂,制备了树脂体系并进行改性研究。对树脂粘度、凝胶时间、DSC 及浇注体力学性能等方面进行了测试。结果表明,通过树脂改性可以增加树脂体系的粘度,减少树脂体系的凝胶时间,树脂体系浇注体的力学性能,随着改性填料的加入呈现出先增强后减小的规律。%The key performance of modified epoxy resin prepared from epoxy resin (4,4 ’-diamino diphenyl methane),silicon carbide,diatomite and curing agent (4,4’-diamino diphenyl sulfone)was researched.Besides viscosity,gel time of resin and mechanical properties of casting body was tested.Experiment showed that the viscosity of the modified resin was higher than the original one,and the gel time was much less.And with the addition of packing the mechanical properties of the modified resin enhanced firstly then decreased.

  14. Epitaxial growth by monolayer restricted galvanic displacement

    Directory of Open Access Journals (Sweden)

    Vasilić Rastko

    2012-01-01

    Full Text Available The development of a new method for epitaxial growth of metals in solution by galvanic displacement of layers pre-deposited by underpotential deposition (UPD was discussed and experimentally illustrated throughout the lecture. Cyclic voltammetry (CV and scanning tunneling microscopy (STM are employed to carry out and monitor a “quasi-perfect”, two-dimensional growth of Ag on Au(111, Cu on Ag(111, and Cu on Au(111 by repetitive galvanic displacement of underpotentially deposited monolayers. A comparative study emphasizes the displacement stoichiometry as an efficient tool for thickness control during the deposition process and as a key parameter that affects the deposit morphology. The excellent quality of layers deposited by monolayer-restricted galvanic displacement is manifested by a steady UPD voltammetry and ascertained by a flat and uniform surface morphology maintained during the entire growth process.

  15. A light-modified ferroelectric resistive switching behavior in Ag/BaMoO4/FTO device at ambient temperature

    Science.gov (United States)

    Zhao, W. X.; Sun, B.; Liu, Y. H.; Wei, L. J.; Li, H. W.; Chen, P.

    2014-12-01

    BaMoO4 powder was prepared by a facile hydrothermal synthesis. And the BaMoO4/FTO device was fabricated by a spin-coated method, in which the thickness of BaMoO4 layer is about 20 μm. The bipolar resistive switching effect has been observed in Ag/BaMoO4/FTO device. Moreover, the resistive switching effect of the device is greatly improved by white light irradiation. The resistive switching behavior is explained by the polarization reversal that changes the charge distribution and modulates the Schottky barriers.

  16. Photocatalytic Properties of TiO2 Thin Films Modified with Ag and Pt Nanoparticles Deposited by Gas Flow Sputtering.

    Science.gov (United States)

    Maicu, M; Glöss, D; Frach, Peter; Hecker, D; Gerlach, G; Córdoba, José M

    2015-09-01

    In this work, a gas flow sputtering (GFS) process which allows the production and deposition of metal nanoparticles (NPs) in a vacuum environment is described. Aim of the study is to prove the potential of this technology for the fabrication of new TiO2 films with enhanced photocatalytic properties. For this purpose, Ag and Pt NPs have been produced and deposited on photocatalytic float glass coated with TiO2 thin films by magnetron sputtering. The influence of the process parameters and of the metal amount on the final properties of the particles (quantity, size, size distribution, oxidation state etc.,) was widely investigated. Moreover, the effect of the NPs on the photocatalytic activity of the resulting materials was evaluated for the case of the decomposition of stearic acid (SA) during UV-A irradiation. The reduction of the water contact angle (WCA) during the irradiation period was measured in order to test the photo-induced super-hydrophilicity (PSH).

  17. Equilibrium adsorption isotherm studies of Cu (II) and Co (II) in high concentration aqueous solutions on Ag-TiO2-modified kaolinite ceramic adsorbents

    Science.gov (United States)

    Ajenifuja, E.; Ajao, J. A.; Ajayi, E. O. B.

    2017-09-01

    Photocatalytic ceramic adsorbents were prepared from locally sourced kaolinite clay minerals for the removal of copper and cobalt ions from high concentration aqueous solutions. The minerals were treated with mild acid before modification using silver nanoparticles sources and titanium-oxide nanoparticles. Batch adsorption experiment was carried out on the targeted ions and the results were analyzed by Langmuir and Freundlich equation at different concentrations (100-1000 mg/l). As-received raw materials do not exhibit any adsorption capacity. However, the adsorption isotherms for modified kaolinite clay ceramic adsorbents could be fitted well by the Langmuir model for Cu2+ and Co2+ with correlation coefficient ( R) of up to 0.99705. The highest and lowest monolayer coverage ( q max) were 93.023 and 30.497 mg/g for Cu2+ and Co2+, respectively. The separation factor ( R L ) was less than one (ceramic adsorbent is favorable. The highest adsorbent adsorption capacity ( K f ) and intensity ( n) constants obtained from Freundlich model are 14.401 (Cu2+ on KLN-T) and 6.057 (Co2+ on KLN-T).

  18. Mechanic studies of monolayer formation on H-Si(111) surfaces

    NARCIS (Netherlands)

    Rijksen, B.M.G.

    2012-01-01

    Covalently attached organic monolayers on silicon surfaces form thermally and chemically stable platforms for (bio)functionalization of the surface. Recent advances in monolayer formation – yielding increases in monolayer quality and the complete exclusion of oxygen at modified surfaces &ndash

  19. Conventional Nanoindentation in Self-Assembled Monolayers Deposited on Gold and Silver Substrates

    Directory of Open Access Journals (Sweden)

    Leila Costelle

    2012-01-01

    Full Text Available Self-assembled monolayers (SAMs are promising materials for micromechanical applications. However, characterization of mechanical properties of monolayers is challenging for standard nanoindentation, and new efficient analysis techniques are needed. Hereby, a conventional nanoindentation method has been combined in a unique way with efficient data analysis based on consumed energy calculation and load-displacement data. The procedure has been applied on SAMs of 4,4′-biphenyldithiol (BPDT on Au, 1-tetradecanethiol (TDT, and 1-hexadecanethiol (HDT on Au and Ag substrates being the first study where SAMs of the same thiols on different substrates are analyzed by nanoindentation providing a new insight into the substrate effects. Unlike TDT and HDT SAMs, which are found to strongly enhance the homogeneity and stiffness of the underlying substrate, the BPDT covered Au substrate appears softer in mechanical response. In the case of TDT and HDT SAMs on Ag the structures are softer showing also faster relaxation than the corresponding structures on Au substrate. The proposed procedure enables a fast and efficient way of assessing the complex behaviour of SAM modified substrates. As a consequence, the results are relevant to practical issues dependent on layer activity and toughness.

  20. Semifluorinated Alkylphosphonic Acids Form High-Quality Self-Assembled Monolayers on Ag-Coated Yttrium Barium Copper Oxide Tapes and Enable Filamentization of the Tapes by Microcontact Printing.

    Science.gov (United States)

    Park, Chul Soon; Lee, Han Ju; Lee, Dahye; Jamison, Andrew C; Galstyan, Eduard; Zagozdzon-Wosik, Wanda; Freyhardt, Herbert C; Jacobson, Allan J; Lee, T Randall

    2016-08-30

    A custom-designed semifluorinated phosphonic acid, (9,9,10,10,11,11,12,12,13,13,14,14,15,15,16,16,16-heptadecafluorohexadecyl)phosphonic acid (F8H8PA), and a normal hexadecylphosphonic acid (H16PA) were synthesized and used to generate self-assembled monolayers (SAMs) on commercially available yttrium barium copper oxide (YBCO) tapes. In this study, we wished to evaluate the effectiveness of these monolayer films as coatings for selectively etching YBCO. Initial films formed by solution deposition and manual stamping using a non-patterned polydimethylsiloxane stamp allowed for a comparison of the film-formation characteristics. The resulting monolayers were characterized by X-ray photoelectron spectroscopy (XPS), contact angle goniometry, and polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS). To prepare line-patterned (filamentized) YBCO tapes, standard microcontact printing (μ-CP) procedures were used. The stamped patterns on the YBCO tapes were characterized by scanning electron microscopy (SEM) before and after etching to confirm the effectiveness of the patterning process on the YBCO surface and energy-dispersive X-ray spectroscopy (EDX) to obtain the atomic composition of the exposed interface.

  1. Physicochemical and biological properties of hydrogel/gelatin/hydroxyapatite PAA/G/HAp/AgNPs composites modified with silver nanoparticles.

    Science.gov (United States)

    Sobczak-Kupiec, Agnieszka; Malina, Dagmara; Piatkowski, Marek; Krupa-Zuczek, Kinga; Wzorek, Zbigniew; Tyliszczak, Bozena

    2012-12-01

    Composites comprising biodegradable polymer matrix, bioactive ceramic fillers and metallic nanoparticles can be applied in the substitution of bone tissue and many others medical and dental applications. Recently, fully resorbable composite materials applicable as bone substitutes are the subject of intensive studies in surgical reconstruction and bone tissue engineering. Biological composites, such as bone and teeth, contain hydroxyapatite (HAp), a mineral component with composition Ca10(PO4)6(OH)2. Silver nanoparticles or silver ions have long been known to have strong inhibitory and bactericidal effects as well as a broad spectrum of antimicrobial activities. In this study we applied natural origin hydroxyapatite obtained from pork bone sludge. As polymer matrix gelatin and poly(acrylic acid) were used. Composite materials were obtained with the use of microwave irradiation. The influence of metallic nanoparticles presence on the degradation process of composite materials was investigated by pH and conductivity analyses of water filtrates. In vitro tests in simulated body fluid (SBF) and artificial saliva confirmed that it is possible to produce hydroxyapatite/polymer composites doped with silver nanoparticles for medical applications. Tests proved that content of silver nanoparticles in composites had influence on degradation behaviour of HA/Polymer/AgNPs in artificial media such as simulated body fluid and saliva.

  2. Nanoindentation Analysis for Mechanical Properties of Electroless NiP Imprinting Mold Replicated from Self-Assembled-Monolayer Modified Master Mold

    Science.gov (United States)

    Lin, Cheng Ping; Saito, Mikiko; Homma, Takayuki

    2013-11-01

    A NiP imprinting mold with patterns, whose size is from nanometer to submicrometer (170, 500, and 1000 nm diameter), was fabricated by electroless deposition of NiP on a 3-aminopropyltriethoxysilane (APTES) modified master mold. The NiP deposit as a replicate mold was then detached from the master mold. The initial NiP deposition in patterns of the master mold was investigated; moreover, nanoindentation was successfully performed on a single NiP pattern for investigating the hardness. The NiP had a similar grain size in different sizes of patterns of the master mold during the initial deposition, as well as the same hardness of the NiP patterns (approximately 12 GPa) was observed. These results indicated that the initial NiP deposition and hardness of NiP were not size dependent above 170 nm. The surface morphology of the NiP detached from the master mold and NiP pattern of different sizes were investigated as well.

  3. Ag Particles Modified Titanium Dioxide Nanotube Array and Its Optical Properties Characterization%Ag颗粒修饰二氧化钛纳米管阵列及其光电性质的表征

    Institute of Scientific and Technical Information of China (English)

    张清林; 王福祥; 夏明霞; 曾亚萍; 曹尚操

    2012-01-01

    Titanium dioxide nanotubes were prepared by anodization and modified with Ag nanoparticlesthrough photochemical reduction of Ag+. The samples were characterized by scanning electron microscopy(SEM), X-ray diffraction(XRD), UV-visible spectroscopy(UV-Vis) and surface photovoltage spectroscopy(SPS). The results exhibit that the Ag/TiO2 nanotubes show strong absorption in the visible region. And the SPS measurements show that with increasing concentration of AgNO3 the surface optical voltage signal enhance.%采用阳极氧化法制备出二氧化钛纳米管阵列,通过光化学还原Ag+的方法,在二氧化钛纳米管表面负载了Ag纳米颗粒.利用扫描电镜(SEM)、X射线衍射仪(XRD)、紫外-可见光谱(UV-Vis)和表面光电压测量仪(SPS)对产物进行了表征.结果表明,该Ag/TiO2纳米管在可见光区域表现出较强的吸收性能.SPS测量表明,随着Ag颗粒浓度的增加,表面光电压信号明显增强.

  4. Sensitive Glycoprotein Sandwich Assays by the Synergistic Effect of In Situ Generation of Raman Probes and Plasmonic Coupling of Ag Core-Au Satellite Nanostructures.

    Science.gov (United States)

    Bi, Xiaoshuang; Li, Xueyuan; Chen, Dong; Du, Xuezhong

    2016-05-01

    Sensitive surface-enhanced Raman scattering (SERS) assays of glycoproteins have been proposed using p-aminothiophenol (PATP)-embedded Ag core-Au satellite nanostructures modified with p-mercaptophenylboronic acid (PMBA) and the self-assembled monolayer of PMBA on a smooth gold-coated wafer. The apparent Raman probe PATP on the surfaces of the Ag cores underwent a photodimerization to generate 4,4'-dimercaptoazobenzene (DMAB) in situ upon excitation of laser, and the in situ generated DMAB acted as the actual Raman probe with considerably strong SERS signals, which was further enhanced by the plasmonic coupling of the Ag core-Au satellite nanostructures due to the synergistic effect. The sandwich assays of glycoproteins showed high sensitivity and excellent selectivity against nonglycoproteins. The Ag core-Au satellite SERS nanostructures can be used for highly sensitive SERS assays of other analytes.

  5. Electrochemical Behavior of Cysteine at Ag2S/Cu2S Nanocrystals Modified Glassy Carbon Electrode%半胱氨酸在Ag2S/Cu2S纳米晶修饰玻碳电极上的电化学行为

    Institute of Scientific and Technical Information of China (English)

    董永平; 黄俐; 张千峰

    2012-01-01

    Ag2S/Cu2S nanocrystals modified glassy carbon electrode(Ag2 S/Cuz S/GCE) was fabricated and the electrochemical behavior of cysteine at the Ag2 S/Cu2 S/GCE was studied. The results showed that Ag2S/Cu2 S/GCE exhibited excellent electrocatalytical activity to the electro-oxidation of cysteine. The potential of oxidation peak was 0. 23 V and the peak current reached 25. 98 juA. The steady-state current changed linearly with cysteine concentration in the range of 1. 0 X 10~s -1. 0 X 10~3 mol/L. The modified electrode exhibited good stability and repeatability.%制备了Ag2S/Cu2S纳米混晶修饰玻碳电极,研究了半胱氨酸在Ag2S/Cu2S纳米混晶修饰电极上的电化学行为.结果表明:Ag2S/Cu2S混晶修饰电极对半胱氨酸的电化学氧化过程具有非常明显的电催化作用,其氧化电位减小为0.23V,氧化峰电流为25.98 μA,与空白电极相比增加了8倍.在1.0×10-5~1.0×10-3 mol/L浓度范围内,稳态电流信号与半胱氨酸浓度呈现良好的线性变化关系.该修饰电极具有良好的稳定性和重现性.

  6. Enhancement of wettability and antibiotic loading/release of hydroxyapatite thin film modified by 100 MeV Ag{sup 7+} ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Elayaraja, K. [Crystal Growth Centre, Anna University, Chennai 600 025 (India); Rajesh, P. [Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Poojappura, Thiruvananthapuram 695 012 (India); Ahymah Joshy, M.I.; Sarath Chandra, V.; Suganthi, R.V. [Crystal Growth Centre, Anna University, Chennai 600 025 (India); Kennedy, J. [National Isotope Centre, GNS Science, 30 Gracefield Road, Lower Hutt (New Zealand); Kulriya, P.K.; Sulania, I.; Asokan, K.; Kanjilal, D.; Avasthi, D.K. [Inter-University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110 067 (India); Varma, H.K. [Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Poojappura, Thiruvananthapuram 695 012 (India); Narayana Kalkura, S., E-mail: kalkurasn@annauniv.edu [Crystal Growth Centre, Anna University, Chennai 600 025 (India)

    2012-05-15

    Highlights: Black-Right-Pointing-Pointer Reduction in particle size on irradiation leading to nanosized HAp. Black-Right-Pointing-Pointer Enhancement of surface roughness and bioactivity on irradiation. Black-Right-Pointing-Pointer Irradiation at lower fluence transforms the surface hydrophobic. Black-Right-Pointing-Pointer The surface turned hydrophilic at higher fluence. Black-Right-Pointing-Pointer Improved drug (amoxicillin) loading on irradiated samples. - Abstract: The effect of swift heavy 100 MeV Ag{sup 7+} ions irradiation was studied on hydroxyapatite (HAp) thin film prepared by pulsed laser deposition technique (PLD). The GIXRD analysis confirmed the absence of any phase in the HAp phase due to irradiation. In addition, there was a considerable decrease in crystallinity and crystallite size on irradiation. There was no significant variation in the stoichiometry of the irradiated films. Irradiation seemed to decrease the optical band gap energy of HAp thin films. The surface roughness, wettability and bioactivity were improved on irradiation of the samples. Amount of amoxicillin loading/release increased (10%) in ion beam irradiated (1 Multiplication-Sign 10{sup 12} ions cm{sup -2}) sample. Irradiated sample showed fast rate of amoxicillin (AMX) release than the pristine. Bactericidal effect was found to increase on irradiation. Surface modified and antibiotics incorporated HAp coated titanium implants may be used to prevent post-surgical infections and to promote bone-bonding of orthopedic devices.

  7. Ag/TiO2-PVA改性无纺布的抗污染性能%Anti-Fouling Performance of Ag/TiO2-PVA Modified Non-woven Fabric

    Institute of Scientific and Technical Information of China (English)

    仉春华; 许英梅; 董玉瑛

    2013-01-01

    以廉价的无纺布为基膜,采用NaBH4还原法制备了Ag/TiO2-PVA复合膜,研究了Ag/TiO2-PVA复合膜作为MBR膜组件处理人工废水的抗污染性能,并对Ag/TiO2-PVA复合膜进行了XRD表征.Ag/TiO2-PVA复合膜的XRD谱图显示出TiO2及Ag的特征峰,说明复合膜表面存在TiQ纳米粒子和单质银.MBR处理人工废水的实验结果表明,Ag/TiO2-PVA复合膜的跨膜压力明显低于对照组,而膜通量则明显高于对照组;膜污染阻力分析表明,Ag/TiO2-PVA复合膜对滤饼层阻力表现出很好的抑制作用;说明Ag/TiO2-PVA复合膜能明显抑制膜污染,具有较好的抗污染性能.Ag/TiO2-PVA复合膜的光催化作用,对废水中有机污染的降解有一定的强化作用,其出水COD平均值低于对照组.Ag/TiO2-PVA致密层的存在提高了无纺布的截留效率,使其出水的浊度低于也对照组.%Ag/TiO2-PVA composite membrane was prepared, which with inexpensive non -woven fabric as support membrane was used in an experimental MBR for studying the anti-fouling performance of the membrane.XRD special graph of Ag/TiO2-PVA composite membrane indicated that there were TiO2 nano-particles and Ag on the membrane surface.The experiment with the MBR treating wastewater samples showed the trans-membrane pressure of the composite membrane was remarkably low, which indicated its good anti-fouling performance.Besides, photo-catalysis of Ag/TiO2-PVA composite membrane could help degrade organic pollutants in the wastewater.

  8. TiO{sub 2} modified with Ag nanoparticles synthesized via ultrasonic atomization-UV reduction and the use of kinetic models to determine the acetic acid photocatalytic degradation

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Yingcao, E-mail: xuyingcao@aliyun.com [State Key Laboratory of Urban Water Resource, Environment, School of Municipal and Environmental Engineering, Harbin Institute of Technology, Harbin 150090 (China); Applied Chemistry Department, School of Science, Northeast Agriculture University, Harbin 150030 (China); You, Hong, E-mail: youhong@hit.edu.cn [State Key Laboratory of Urban Water Resource, Environment, School of Municipal and Environmental Engineering, Harbin Institute of Technology, Harbin 150090 (China)

    2014-12-01

    Highlights: • The first use of ultrasonic atomization-UV reduction for modifying Ag on TiO{sub 2}. • The first use of kinetics models for the establishment of the photocatalytic degradation of acetic acid using a hyperbolic mathematical model and introducing the concentration factor (α) in the dynamic model. • Photocatalytic experiment design using double-sided TiO{sub 2} and a double-light source. - Abstract: TiO{sub 2} surfaces modified with noble metal nanoparticles have been found to effectively reduce the photogenerated carrier recombination rate and significantly extend the light absorption properties of TiO{sub 2}, thereby greatly increasing its photocatalytic activity. In this paper, highly ordered, double-sided TiO{sub 2} nanotube arrays were prepared using an anodic oxidation method in a home-made reactor using glycerol/water (volume ratio 2:1) and NH{sub 4}F (0.25 mol/L) as the electrolyte, titanium plates (10 cm × 2 cm × 0.5 mm) as the anode and graphite as the cathode at a constant voltage of 25 V. After a 2-h reaction, anatase TiO{sub 2} nanotubes were obtained upon calcination at 450 °C for 4 h. The Ag nanoparticles on the surfaces of the TiO{sub 2} were prepared via ultrasonic atomization-ultraviolet light reduction. First, a silver nitrate solution was sputtered into small droplets under ultrasonication. Then, the Ag{sup +} droplets were reduced to Ag nanoparticles. The surface morphologies, structures and elemental compositions were characterized using SEM, EDS, XRD and XPS. The photocatalytic activities were determined in acetic acid solutions (40–200 mg/L), and a mathematical model for catalytic degradation was established based on a hyperbolic model. The SEM results showed that the diameters of the as-prepared Ag/TiO{sub 2} are approximately 100 nm and that the lengths are approximately 1.8 μm. The XRD crystal structure analysis shows that the anatase phase of the TiO{sub 2} does not change during the Ag modification, and there was

  9. Ultrasensitive electrochemical immunoassay for CEA through host-guest interaction of β-cyclodextrin functionalized graphene and Cu@Ag core-shell nanoparticles with adamantine-modified antibody.

    Science.gov (United States)

    Gao, Jian; Guo, Zhankui; Su, Fengjie; Gao, Liang; Pang, Xuehui; Cao, Wei; Du, Bin; Wei, Qin

    2015-01-15

    A novel non-enzymatic immunoassay was designed for ultrasensitive electrochemical detection of carcino-embryonic antigen (CEA) using β-cyclodextrin functionalized Cu@Ag (Cu@Ag-CD) core-shell nanoparticles as labels and β-cyclodextrin functionalized graphene nanosheet (CD-GN) as sensor platform. CD-GN has excellent conductivity which promoted the electric transmission between base solution and electrode surface and enhanced sensitivity of immunosensor. In addition, owing to supramolecular recognition of CD-GN for the guest molecule, quite a few synthesized adamantine-modified primary antibodies (ADA-Ab1) were immobilized on the CD-GN by supramolecular host-guest interaction between CD and ADA. Cu@Ag-CD as a signal tag could be captured by ADA-modified secondary antibody (ADA-Ab2) through a host-guest interaction, leading to a large loading of Cu@Ag nanoparticles with high electrical conductivity and catalytic activity. The fabricated immunosensor exhibits excellent analytical performance for the measurement of CEA with wide range linear (0.0001-20 ng/mL), low detection limit (20 fg/mL), good sensitivity, reproducibility and stability, which provide an enormous application prospect in clinical diagnostics.

  10. Structural, thermal, laser damage, photoconductivity, NLO and mechanical properties of modified vertical Bridgman method grown AgGa0.5In0.5Se2 single crystal

    Science.gov (United States)

    Vijayakumar, P.; Ramasamy, P.

    2016-08-01

    AgGa0.5In0.5Se2 single crystal was grown using modified vertical Bridgman method. The structural perfection of the AgGa0.5In0.5Se2 single crystal has been analyzed by high-resolution X-ray diffraction rocking curve measurements. The structural and compositional uniformities of AgGa0.5In0.5Se2 were studied using Raman scattering spectroscopy at room temperature. The FWHM of the Γ1 (W1) and Γ5L (Γ15) measured at different regions of the crystal confirms that the composition throughout its length is fairly uniform. Thermal properties of the as-grown crystal, including specific heat, thermal diffusivity and thermal conductivity have been investigated. The multiple shot surface laser damage threshold value was measured using Nd:YAG laser. Photoconductivity measurements with different temperatures have confirmed the positive photoconducting behavior. Second harmonic generation (SHG) on powder samples has been measured using the Kurtz and Perry technique and the results display that AgGa0.5In0.5Se2 is a phase-matchable NLO material. The hardness behavior has been measured using Vickers micro hardness measurement and the indentation size effect has been observed. The classical Meyer's law, propositional resistance model and modified propositional resistance model have been used to analyse the micro hardness behavior.

  11. Disinfection of Escherichia coli Gram negative bacteria using surface modified TiO2: optimization of Ag metallization and depiction of charge transfer mechanism.

    Science.gov (United States)

    Gomathi Devi, LakshmipathiNaik; Nagaraj, Basavalingaiah

    2014-01-01

    The antibacterial activity of silver deposited TiO2 (Ag-TiO2 ) against Gram negative Escherichia coli bacteria was investigated by varying the Ag metal content from 0.10 to 0.50% on the surface of TiO2 . Ag depositions by the photoreduction method were found to be stable. Surface silver metallization was confirmed by EDAX and XPS studies. Photoluminescence studies show that the charge carrier recombination is less for 0.1% Ag-TiO2 and this catalyst shows superior bactericidal activity under solar light irradiation compared to Sol gel TiO2 (SG-TiO2 ) due to the surface plasmon effect. The energy levels of deposited Ag are dependent on the Ag content and it varies from -4.64 eV to -1.30 eV with respect to the vacuum energy level based on atomic silver to bulk silver deposits. The ability of electron transfer from Ag deposit to O2 depends on the position of the energy levels. The 0.25% and 0.50% Ag depositions showed detrimental effect on bactericidal activity due to the mismatch of energy levels. The effect of the EROS (External generation of the Reactive Oxygen Species by 0.1% Ag-TiO2 ) and IROS (Interior generation of Reactive Oxygen Species within the bacteria) on the bactericidal inactivation is discussed in detail.

  12. Electrochemical Properties of Organosilane Self Assembled Monolayers on Aluminum 2024

    Science.gov (United States)

    Hintze, Paul E.; Calle, Luz Marina

    2004-01-01

    Self assembled monolayers are commonly used to modify surfaces. Within the last 15 years, self assembled monolayers have been investigated as a way to protect from corrosion[1,2] or biofouling.[3] In this study, self assembled monolayers of decitriethoxysilane (C10H21Si(OC2H5)3) and octadecyltriethoxysilane (C18H37Si(OC2H5)3) were formed on aluminum 2024-T3. The modified surfaces and bare Al 2024 were characterized by dynamic water contact angle measurements, x-ray photoelectron spectroscopy (XIPS) and infrared spectroscopy. Electrochemical impedance spectroscopy (EIS) in 0.5 M NaCl was used to characterize the monolayers and evaluate their corrosion protection properties. The advancing water contact angle and infrared measurements show that the mono layers form a surface where the hydrocarbon chains are packed and oriented away from the surface, consistent with what is found in similar systems. The contact angle hysteresis measured in these systems is relatively large, perhaps indicating that the hydrocarbon chains are not as well packed as monolayers formed on other substrates. The results of the EIS measurements were modeled using a Randle's circuit modified by changing the capacitor to a constant phase element. The constant phase element values were found to characterize the monolayer. The capacitance of the monolayer modified surface starts lower than the bare Al 2024, but approaches values similar to the bare Al 2024 within 24 hours as the monolayer is degraded. The n values found for bare Al 2024 quickly approach the value of a true capacitor and are greater than 0.9 within hours after the start of exposure. For the monolayer modified structure, n can stay lower than 0.9 for a longer period of time. In fact, n for the monolayer modified surfaces is different from the bare surface even after the capacitance values have converged. This indicates that the deviation from ideal capacitance is the most sensitive indicator of the presence of the monolayer.

  13. 表面修饰Ag2S纳米微粒的合成及摩擦学行为研究%Synthesis and Tribological Behaviors of Surface-Modified Ag2S Nanoparticles

    Institute of Scientific and Technical Information of China (English)

    周静芳; 陶小军; 张治军; 刘维民; 薛群基

    1999-01-01

    在水醇混合介质中,采用同阳离子共沉淀法合成了有机化合物表面修饰的Ag2S纳米微粒,在高速钢基底上制备成膜,研究了它的摩擦学特性.结果表明:修饰后的Ag2S纳米微粒粒径小,性能稳定,在有机介质中分散成透明溶液.AgDDP膜和Ag2S-DDP膜均可显著降低钢基底的摩擦系数.研究证实表面修饰Ag2S纳米微粒的摩擦作用机制是在较低负荷下表面修饰层起主要作用,在较高负荷下Ag2S纳米核起主要的承载和减摩抗磨作用.

  14. Synthesis and photocatalytic activity of Ag@AgCl modified anatase TiO2 with reactive (001) facet%Ag@AgCl修饰的具有高活性(001)晶面的锐钛矿相TiO2的制备和光催化性能研究

    Institute of Scientific and Technical Information of China (English)

    罗秀针; 袁霞; 陈驰; 高碧芬

    2014-01-01

    本文采用水热法合成具有高活性(001)晶面的锐铁矿相TiO2微球,利用沉积法将AgCl分散到TiO2微球表面,再通过光化学反应将部分Ag还原,获得Ag@AgCl等离子体负载的TiO2光催化剂,借助SEM、TEM、UV-Vis DRS等手段对催化剂的结构进行表征,并以酸性红作为模型污染物对样品的光催化性能进行评价.结果表明:经Ag@AgC1修饰后,样品对可见光的响应增强,光生载流子的分离得到有效促进,可见光催化活性有大幅度的提高,对酸性红的降解效率是修饰前的3倍.

  15. Nucleation and Growth of Cu-Al Intermetallics in Al-Modified Sn-Cu and Sn-Ag-Cu Lead-Free Solder Alloys

    Science.gov (United States)

    Reeve, Kathlene N.; Anderson, Iver E.; Handwerker, Carol A.

    2015-03-01

    Lead-free solder alloys Sn-Cu (SC) and Sn-Ag-Cu (SAC) are widely used by the microelectronics industry, but enhanced control of the microstructure is needed to improve solder performance. For such control, nucleation and stability of Cu-Al intermetallic compound (IMC) solidification catalysts were investigated by variation of the Cu (0.7-3.0 wt.%) and Al (0.0-0.4 wt.%) content of SC + Al and SAC + Al alloys, and of SAC + Al ball-grid array (BGA) solder joints. All of the Al-modified alloys produced Cu-Al IMC particles with different morphologies and phases (occasionally non-equilibrium phases). A trend of increasing Cu-Al IMC volume fraction with increasing Al content was established. Because of solidification of non-equilibrium phases in wire alloy structures, differential scanning calorimetry (DSC) experiments revealed delayed, non-equilibrium melting at high temperatures related to quenched-in Cu-Al phases; a final liquidus of 960-1200°C was recorded. During cooling from 1200°C, the DSC samples had the solidification behavior expected from thermodynamic equilibrium calculations. Solidification of the ternary alloys commenced with formation of ternary β and Cu-Al δ phases at 450-550°C; this was followed by β-Sn, and, finally, Cu6Sn5 and Cu-Al γ1. Because of the presence of the retained, high-temperature phases in the alloys, particle size and volume fraction of the room temperature Cu-Al IMC phases were observed to increase when the alloy casting temperature was reduced from 1200°C to 800°C, even though both temperatures are above the calculated liquidus temperature of the alloys. Preliminary electron backscatter diffraction results seemed to show Sn grain refinement in the SAC + Al BGA alloy.

  16. Removal of gas phase low-concentration toluene over Mn, Ag and Ce modified HZSM-5 catalysts by periodical operation of adsorption and non-thermal plasma regeneration.

    Science.gov (United States)

    Wang, Wenzheng; Wang, Honglei; Zhu, Tianle; Fan, Xing

    2015-07-15

    Ag/HZSM-5, Mn/HZSM-5, Ce/HZSM-5, Ag-Mn/HZSM-5 and Ce-Mn/HZSM-5 were prepared by impregnation method. Both their adsorption capacity and catalytic activity were investigated for the removal of gas phase low-concentration toluene by periodical operation of adsorption and non-thermal plasma regeneration. Results show that catalysts loaded with Ag (Ag/HZSM-5 and Ag-Mn/HZSM-5) had larger adsorption capacity for toluene than the other catalysts. And Ag-Mn/HZSM-5 displayed the best catalytic performance for both toluene oxidation by non-thermal plasma and byproducts suppression. On the other hand, the deactivated catalyst can be fully regenerated by calcining in air stream when its adsorption capacity and catalytic activity of the Ag-Mn/HZSM-5 catalyst was found to be decreased after 10 cycles of periodical adsorption and non-thermal regeneration. Copyright © 2015. Published by Elsevier B.V.

  17. A highly sensitive self assembled monolayer modified copper doped zinc oxide nanofiber interface for detection of Plasmodium falciparum histidine-rich protein-2: Targeted towards rapid, early diagnosis of malaria.

    Science.gov (United States)

    Brince Paul, K; Kumar, Sanni; Tripathy, Suryasnata; Vanjari, Siva Rama Krishna; Singh, Vikrant; Singh, Shiv Govind

    2016-06-15

    Rapid, ultrasensitive diagnostic/triaging kits for early detection of malarial parasites are critical for prevention of malarial epidemic, especially in developing and tropical countries. Unlike traditional microscopic diagnosis, these kits rely on the detection of antigens specific to malarial parasites. One such antigen which is routinely used in these diagnostic kits is Histidine-rich protein-2; a protein synthesized and released into the blood stream by the parasite Plasmodium falciparum. In this paper, we demonstrate an ultrasensitive nanobiosensor detection platform for Histidine-rich protein-2 having a limit of detection of attogram/ml. This nanobiosensor platform comprises of Mercaptopropylphosphonic acid functionalized copper doped zinc oxide nanofibers synthesized by electrospinning technique. Ultrasensitivity of attogram/ml can be attributed to the complimentary effects of Mercaptopropylphosphonic acid and copper doping in zinc oxide. Mercaptopropylphosphonic acid enhances the functional groups required for immobilizing antibody. Copper doping in zinc oxide not only increases the conductivity of the nanofibers but also pre-concentrates the target analyte onto the Mercaptopropylphosphonic acid treated nanofiber surface due to inherent electric field generated at the copper/zinc oxide heterojunction interface. The impedimetric detection response of copper-doped zinc oxide nanofiber modified electrode shows excellent sensitivity (28.5 kΩ/(gm/ml)/cm(2)) in the detection ranges of 10 ag/ml-10 µg/ml, and a detection limit of 6 attogram/ml. In addition, the proposed biosensor is highly selective to targeted HRP2 protein with a relative standard deviation of 1.9% in the presence of various interference of nonspecific molecules. To the best of our knowledge, this biosensor shows the lowest detection limit of malarial parasites reported in the literature spanning different nanomaterials and different detection mechanisms. Since the nanobiosensor platform is

  18. Hydrothermal synthesis and photocatalytic properties of Ag ions modified Bi2 WO6%水热合成Ag离子改性修饰Bi2WO6及其光催化性能

    Institute of Scientific and Technical Information of China (English)

    赵雯; 胡朝浩; 黄伟; 陈冉; 吕丰正; 钟燕; 周怀营

    2014-01-01

    A series of Ag ions modified Bi2 WO6 photocatalyst were synthesized successfully by hydrothermal method with solid silver nitrate and characterized by X-ray diffraction (XRD),field emission scanning electron microscope (FESEM),X-ray photoelectron spectrometer (XPS),energy dispersive X-ray detector (EDS)and UV-Vis diffusion reflectance spectra techniques (DRS).The result indicated that Ag ions may replace Bi3+ ions of bismuth tungstate into the crystal lattice,which regulates the forbidden band width.On the other hand, pure Bi2 WO6 and Ag ions modified Bi2 WO6 were both ball-like samples self-assembled with nanoplates.Com-pared with pure Bi2 WO6 ,Ag ions modified Bi2 WO6 samples have higher crystallinity and relatively closer ar-rangement in nanoplates,also more prominent photocatalytic activity.The optimization of morphology and en-ergy gap was the main reason to enhance the photocatalytic performance in this experiment.And the degrada-tion rate of RhB was increased by almost 42% while the quantity of AgNO3 adding content was 10 mol%.%通过水热法以固体 AgNO3为 Ag 离子来源,成功制备出系列 Ag 离子改性修饰 Bi2 WO6复合光催化剂,并采用 X 射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、X 射线光电子能谱仪(XPS)、能谱仪(EDS)和紫外-可见漫反射光谱(DRS)技术对其进行分析表征。研究表明,Ag 离子可能取代 Bi2 WO6中的Bi3+离子进入晶格,从而调节了禁带宽度。另一方面,纯Bi2 WO6与Ag离子改性修饰Bi2 WO6样品均为由纳米片自组装而成的球形结构,直径约为2~6μm。与纯Bi2 WO6相比,Ag离子改性修饰Bi2 WO6样品的结晶度较高且纳米片的排列也更致密,其光催化活性明显提高。在本文中形貌和能隙的优化是光催化性能提升的主要原因。当AgNO3的投加量为10%(摩尔分数)时,罗丹明B的降解率提高了近42%。

  19. Superatomic S(2) silver clusters stabilized by a thiolate-phosphine monolayer: insight into electronic and optical properties of Ag14(SC6H3F2)12(PPh3)8 and Ag16(SC6H3F2)14(DPPE)4.

    Science.gov (United States)

    Gell, Lars; Lehtovaara, Lauri; Häkkinen, Hannu

    2014-09-18

    The electronic structure of two recently crystallographically solved, thiolate-phosphine protected silver clusters Ag14 and Ag16 are analyzed via density functional theory (DFT) and their optical excitations are analyzed from time-dependent DFT perturbation theory. Both clusters can be characterized as having the S(2) free-electron configuration in the metal core, which is the first time such a configuration is confirmed for structurally known ligand-protected noble metal clusters. However, their different core shapes and ligand layer induce significantly different optical spectra. Performance of gradient-corrected DFT functionals is discussed and it is shown that the asymptotically correct Leeuwen-Baerends LB94 functional reproduces the optical spectrum of Ag14 in a good agreement with experiment. Choice of the functional becomes important for clusters where the optical transitions are dominated by the electron-rich ligand layer.

  20. Absence of a Dirac cone in silicene on Ag(111): First-principles density functional calculations with a modified effective band structure technique

    Science.gov (United States)

    Wang, Yun-Peng; Cheng, Hai-Ping

    2013-06-01

    We investigate the currently debated issue of the existence of the Dirac cone in silicene on an Ag(111) surface, using first-principles calculations based on density functional theory to obtain the band structure. By unfolding the band structure in the Brillouin zone of a supercell to that of a primitive cell, followed by projecting onto Ag and silicene subsystems, we demonstrate that the Dirac cone in silicene on Ag(111) is destroyed. Our results clearly indicate that the linear dispersions observed in both angular-resolved photoemission spectroscopy [P. Vogt , Phys. Rev. Lett.PRLTAO0031-900710.1103/PhysRevLett.108.155501 108, 155501 (2012)] and scanning tunneling spectroscopy [L. Chen , Phys. Rev. Lett.PRLTAO0031-900710.1103/PhysRevLett.109.056804 109, 056804 (2012)] come from the Ag substrate and not from silicene.

  1. Synthesis, characterization and visible-light photocatalytic performance of Ag{sub 2}CO{sub 3} modified by graphene-oxide

    Energy Technology Data Exchange (ETDEWEB)

    Song, Yongxiu [School of Chemistry and Chemical Engineering, Jiangsu University, Zhenjiang 212013 (China); Zhu, Jiaxiang [School of the Environment, Jiangsu University, Zhenjiang 212013 (China); Xu, Hui, E-mail: xh@ujs.edu.cn [School of the Environment, Jiangsu University, Zhenjiang 212013 (China); Wang, Cheng [School of the Environment, Jiangsu University, Zhenjiang 212013 (China); Xu, Yuanguo; Ji, Haiyan; Wang, Kun [School of Chemistry and Chemical Engineering, Jiangsu University, Zhenjiang 212013 (China); Zhang, Qi, E-mail: qzhang@ujs.edu.cn [School of Chemistry and Chemical Engineering, Jiangsu University, Zhenjiang 212013 (China); Li, Huaming [School of Chemistry and Chemical Engineering, Jiangsu University, Zhenjiang 212013 (China)

    2014-04-01

    Highlights: • The GO/Ag{sub 2}CO{sub 3} composite based on GO was prepared by a facile one-step synthesis. • The photocatalytic degradation followed the pseudo-first-order reaction model. • GO promoted the separation of photoexcited electron–hole pairs in the GO/Ag{sub 2}CO{sub 3}. - Abstract: Ag{sub 2}CO{sub 3} coupled with graphene-oxide composites were prepared by a facile one-step synthesis. The samples were characterized by Scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), Fourier transformed infrared (FT-IR) spectroscopy and Raman spectra. The as-prepared graphene-oxide/Ag{sub 2}CO{sub 3} (GO/Ag{sub 2}CO{sub 3}) exhibited universally high photocatalytic activity toward typical methylene blue (MB) and methyl orange (MO) in aqueous solution. A possible photocatalytic mechanism was investigated by a series of radical trapping experiment. The kinetics of the GO/Ag{sub 2}CO{sub 3} composites were also proposed. The result showed that GO might serve as an electron collector and a transporter to promote the separation of photoexcited electron–hole pairs and to decrease the possibility of electron and hole recombination efficiently. This work has set up a simple method for exploring the excellent GO-based photocatalysts.

  2. Preparation and biocompatibility of BSA monolayer on silicon surface.

    Science.gov (United States)

    Tao, Caihong; Zhang, Junyan; Yang, Shengrong

    2011-06-01

    This paper describes a general strategy for grafting protein molecules on silicon surface by using dopamine as adhesive layer. With this method, silicon surface had been successfully modified by BSA monolayer. Fourier transform infrared spectra, X-ray photoelectron spectroscopy, contact angle analysis and atomic force microscopy confirmed the sequential grafting of initiator and protein molecules. Cell adhesion experiments with PC-12 cells showed that the obtained monolayer exhibits good biocompatibility. The corrosion resistance behavior of the polydopamine and BSA modified silicon wafers was investigated by potentiodynamic test, which indicated that the modified surfaces exhibited a better anti-corrosion capability than silicon surface. All these results must be valuable for the application of protein monolayer in biological and biomedical technology.

  3. CdS、Ag+掺杂改性纳米TiO2光催化降解甲基橙动力学研究%Kinetics of Photocatalytic Degrading Helianthine with Nano-TiO2 Modified by Doped CdS, Ag

    Institute of Scientific and Technical Information of China (English)

    李琴

    2011-01-01

    The exploring process of the kinetics on the performance of photocatalytic degrading helianthine with nano TiO2 and its modified photocatalytic agent CdS/TiO2 and Ag+/TiO2 is introduced in this paper after the optimum condition of helianthine being degraded by photocatalytic nano TiO2 is determined. The results indicate that the photocatalytic reaction of nano TiO2 and its modified CdS/TiO2, Ag+ /TiO2 are in accordance with the characteristic of the first order reaction. An induction period exists in all of the three kinds of photocatalytic reaction agent, of which, the nano TiO2 is the longest, and Ag + /TiO2 is longer, and the CdS/TiO2 is the shortest. The efficiencies, however, are in reverse order.%在探索纳米TiO2光催化降解甲基橙的最佳条件后,对纳米TiO2及其改性光催化剂CdS/TiO2、Ag +/TiO2光催化降解甲基橙性能进行了动力学研究,结果表明:纳米TiO2及其改性的CdS/TiO2、Ag +/TiO2的光催化反应符合动力学一级反应规律;三种光催化反应剂的光催化均存在诱导期,其中纳米TiO2光催化反应诱导期最长,其次是Ag+/TiO2光催化反应,而CdS/TiO2光催化反应诱导期最短;光催化反应降解甲基橙效率是:TiO2光催化反应最低,其次是Ag+/TiO2,CdS/TiO2效率最高.

  4. Effects of Ge replacement in GeTe by Ag or Sb on the Seebeck coefficient and carrier concentration modified by local electron imbalance

    Science.gov (United States)

    Levin, E. M.; Howard, A.; Straszheim, W. E.

    2015-03-01

    XRD, SEM, EDS, 125Te NMR, Seebeck coefficient, and electrical resistivity of AgxGe50-xTe50 and SbxGe50-xTe50 alloys have been studied. Replacement of Ge in GeTe by Sb significantly increases the Seebeck coefficient, while replacement by Ag decreases it. These effects can be attributed to a change in carrier concentration observed via 125Te NMR spin-lattice relaxation measurements and NMR signal position, which mostly depends on the Knight shift. Variation in carrier concentration in AgxGe50-xTe50 and SbxGe50-xTe50 can be attributed to different electron configurations of valence electrons of Ag (4d105s1) and Sb (5s25p3) compared to that of Ge (4s24p2) resulting in local electron imbalances and changing the concentration of charge carrier (holes) generated by Ge vacancies. In contrast, our 125Te NMR and Seebeck coefficient data for Ag2Sb2Ge46Te50 are similar to those observed for GeTe. This shows that effects from Ag and Sb compensate each other and indicates the existence of [Ag +Sb] pairs. The effects of Ge replacement in GeTe by Ag, Sb, or [Ag +Sb] on rhombohedral lattice distortion also have been analyzed. Interplay between the Seebeck coefficient and electrical resistivity in these alloys results in variation of power factor; the value of 45 mW/cm K2, the highest among known tellurides, was found for Sb2Ge48Te50.

  5. Surface-enhanced Raman scattering from AgNP-graphene-AgNP sandwiched nanostructures.

    Science.gov (United States)

    Wu, Jian; Xu, Yijun; Xu, Pengyu; Pan, Zhenghui; Chen, Sheng; Shen, Qishen; Zhan, Li; Zhang, Yuegang; Ni, Weihai

    2015-11-07

    We developed a facile approach toward hybrid AgNP-graphene-AgNP sandwiched structures using self-organized monolayered AgNPs from wet chemical synthesis for the optimized enhancement of the Raman response of monolayer graphene. We demonstrate that the Raman scattering of graphene can be enhanced 530 fold in the hybrid structure. The Raman enhancement is sensitively dependent on the hybrid structure, incident angle, and excitation wavelength. A systematic simulation is performed, which well explains the enhancement mechanism. Our study indicates that the enhancement resulted from the plasmonic coupling between the AgNPs on the opposite sides of graphene. Our approach towards ideal substrates offers great potential to produce a "hot surface" for enhancing the Raman response of two-dimensional materials.

  6. Ag modified LaMnO3 nanorods-reduced graphene oxide composite applied in the photocatalytic discoloration of direct green

    Science.gov (United States)

    Hu, Jie; Liu, Yuanyuan; Men, Jie; Zhang, Liang; Huang, Hao

    2016-11-01

    A new nanostructure photocatalyst, incorporating Ag and reduced graphene oxide (rGO) with LaMnO3-nanorods have been fabricated via two-step synthetic approaches by using Cetyltrimethyl Ammonium Bromide (CTAB) as a template via a simple hydrothermal reaction and the decoration of Ag nanoparticles is through a traditional silver mirror reaction. The characteristic of the materials are examined by XRD, TEM, FE-SEM and XPS. The results confirm that the LaMnO3 nanorods are perovskite phase and uniform dispersed on the surface of rGO. The Ag nanoparticles is deposited the surface of LaMnO3-nanorods with its metal form. The Ag/LaMnO3-nanorods/rGO exhibit an excellent performance in the photo-degradation of Direct Green BE under the UV-vis irradiation. As an electron capture agent, metal Ag can capture the e- that transported along the LMO-NR, thereby leading to effective separation of the e--h+ pairs and accelerate the transfer of surface charge, which is further demonstrated by the Photoluminescence (PL) spectra, cyclic voltammetry (CV) and AC impedance spectra.

  7. Surface-enhanced Raman scattering from AgNP-graphene-AgNP sandwiched nanostructures

    Science.gov (United States)

    Wu, Jian; Xu, Yijun; Xu, Pengyu; Pan, Zhenghui; Chen, Sheng; Shen, Qishen; Zhan, Li; Zhang, Yuegang; Ni, Weihai

    2015-10-01

    We developed a facile approach toward hybrid AgNP-graphene-AgNP sandwiched structures using self-organized monolayered AgNPs from wet chemical synthesis for the optimized enhancement of the Raman response of monolayer graphene. We demonstrate that the Raman scattering of graphene can be enhanced 530 fold in the hybrid structure. The Raman enhancement is sensitively dependent on the hybrid structure, incident angle, and excitation wavelength. A systematic simulation is performed, which well explains the enhancement mechanism. Our study indicates that the enhancement resulted from the plasmonic coupling between the AgNPs on the opposite sides of graphene. Our approach towards ideal substrates offers great potential to produce a ``hot surface'' for enhancing the Raman response of two-dimensional materials.We developed a facile approach toward hybrid AgNP-graphene-AgNP sandwiched structures using self-organized monolayered AgNPs from wet chemical synthesis for the optimized enhancement of the Raman response of monolayer graphene. We demonstrate that the Raman scattering of graphene can be enhanced 530 fold in the hybrid structure. The Raman enhancement is sensitively dependent on the hybrid structure, incident angle, and excitation wavelength. A systematic simulation is performed, which well explains the enhancement mechanism. Our study indicates that the enhancement resulted from the plasmonic coupling between the AgNPs on the opposite sides of graphene. Our approach towards ideal substrates offers great potential to produce a ``hot surface'' for enhancing the Raman response of two-dimensional materials. Electronic supplementary information (ESI) available: Additional SEM images, electric field enhancement profiles, Raman scattering spectra, and structure-dependent peak ratios. See DOI: 10.1039/c5nr04500b

  8. 制备源自HBsAg基因修饰树突状细胞的外切体%Generation of exosomes derived from adenovirus-mediated HBsAg gene-modified dendritic cells

    Institute of Scientific and Technical Information of China (English)

    杨静悦; 高琳; 付蓉; 薛妍; 刘文超

    2012-01-01

    Objective: To obtain exosomes derived from adenovirus - mediated HBsAg gene - modified dendritic cells. Methods: Full length HBsAg cDNAs were cloned into shuttle2 vector. The HBsAg gene fragments resulted from the - S digested with PI - See and I - Ceu were linked to the linear adeno - X virus DNA. After packaged with HEK293 cells, the adenovirus expression vector was obtained. Then the recombinant adenovirus expression plasmid AdVHBsAg was transfected into human monocyte - derived dendritic cells. The exosomes were isolated from superna-tant of transfected DCs. Transmission electron microscopy was used to observe their structures. The expressions of several proteins were investigated by flow cytometry. Results: The shuttle2 - S showed that band with 630 bp by di-gested with PI - See and I - Ceu, HBsAg gene in the inserted DNA of AdVHBsAg was confirmed by PCR, and pre-dictive fragments proved by restriction enzyme digestion analysis were exhibited. CPE appear 10 after days HEK293 cells transfected AdVHBsAg. Application of the isolation procedure to transfected DCs revealed exosome vesicles by transmission electron microscopy. Protein analysis by Western blot was performed and revealed that the costimulatory molecule CD86,CD83 and HBsAg was detectable. Conclusion; The exosomes derived from HBsAg - DC may be a tool of the HBV related hepatocellular carcinoma immunotherapy.%目的:制备一种新型负载HBsAg基因的外切体(exosome)瘤苗,并探讨其生物学特性、免疫学功能.方法:运用分子克隆和病毒载体转染HBsAg基因构建AdVHBsAg-DC肝癌瘤苗,采用流式细胞术鉴定转染基因表达;提取exosome;以透射电镜观察、Western blot法鉴定exosome.结果:构建的重组AdVHBsAg腺病毒载体,经PCR和酶切鉴定,结果显示HBsAg基因片段已正确插入腺病毒载体中.包装的腺病毒载体具有良好的感染性,可以在293细胞中形成病毒颗粒.提取的exosome在透射电镜下可观察到直径为50-100nm

  9. Electrochemiluminescent immune-modified electrodes based on Ag2Se@CdSe nanoneedles loaded with polypyrrole intercalated graphene for detection of CA72-4.

    Science.gov (United States)

    Lv, Xiaohui; Pang, Xuehui; Li, Yueyun; Yan, Tao; Cao, Wei; Du, Bin; Wei, Qin

    2015-01-14

    This work described a new electrochemiluminescence (ECL) immunosensor based on polypyrrole intercalated graphene and Ag2Se@CdSe nanoneedles. The novel nanomaterial Ag2Se@CdSe, with needle-like morphology, was synthesized for the first time. The prepared Ag2Se@CdSe nanoneedles exhibited good luminous performance in the presence of K2S2O8. Polypyrrole intercalated amination graphene with high specific binding sites and excellent electrochemical performance was used as the platform for the sensor. The developed ECL immunosensor was used for the detection of CA72-4 with good linear relation in the range from 10(-4) to 20 U/mL and low detection limit of 2.1 × 10(-5) U/mL (S/N = 3). The developed ECL immunosensor with high sensitivity and spectral selectivity can be used for detection of real samples. Ag2Se@CdSe nanoneedles could be promising candidate emitter for ECL biosensors in the future.

  10. Ag(Ⅰ) Schiff碱配合物改性MCM-41分子筛的制备和表征%PREPARATION AND CHARACTERIZATION OF Ag(Ⅰ) SCHIFF BASE COMPLEX MODIFIED MCM?41 MOLECULAR SIEVES

    Institute of Scientific and Technical Information of China (English)

    康文彬; 喻龙宝; 黄竹谋; 施亚玉

    2010-01-01

    以3-氨丙基三乙氧基硅烷(3-aminopropyltriethoxysilane,APS)为偶联剂,用共缩聚的方法合成了氨基官能化的MCM-41介孔分子筛(amino-functionalized mesoporous MCM-41,AP-MCM-41),在分子筛孔道和表面共价偶联Ag(Ⅰ) Schiff碱配合物.采用X射线衍射、Fourier红外光谱、紫外-可见光谱、氮气吸附/脱附、元素分析和透射电子显微镜对得到的样品进行了表征.结果表明:Ag(Ⅰ) Schiff 碱配合物被成功嫁接到了分子筛的孔道和表面上,而且嫁接后的MCM-41仍然具有较好的孔径分布和有序结构,比表面积达到712.59 m~2/g,最可几孔径为3.41 nm,具有典型的介孔材料特征.透射电子显微镜观察显示具有明显的孔道结构,并且较为规整.紫外-可见光谱显示,金属配位后,样品的相应的归属峰发生了明显的漂移,说明Ag(Ⅰ) Schiff碱配合物已嫁接到了MCM-41表面并形成牢固的结构.

  11. Grafted silane monolayers: reconsideration of growth mechanisms

    Science.gov (United States)

    Ivanov, D. A.; Nysten, B.; Jonas, A. M.; Legras, R.

    1998-03-01

    Chemical force microscopy is a new technique devised to image chemical heterogeneities on surfaces. It requires the chemical modification of Atomic Force Microscopy (AFM) tips in order to create chemical probes. In this respect, self-assembled monolayers (SAM) of alkylchlorosilanes are particularly interesting as modifying agents for AFM tips. We report here our results on the kinetics of silanization and on the structure of such SAM's grafted on model surfaces (hydroxylated Si(100) wafers). AFM, contact angle measurements, X-ray reflectivity and X-ray photoelectron spectroscopy were used to characterize SAM's of octadecyltrichlorosilane (OTS) and octadecyldimethylchlorosilane (ODMS) grown from hexadecane and toluene solutions. The mechanism of grafting of OTS follows two stages. The first rapid stage corresponds to the nucleation and growth of island-like monolayer domains. The second slower stage is related to the densification of the monolayer. SAM's of ODMS were found to form thinner layers as compared to OTS, due to their lower grafting density probably resulting in a more disordered state of grafted alkyl chains. We also address the problems concerning the relationships between the quality of final SAM structures and the water content as well as the nature of the solvent used for silanization.

  12. Tuning of metal work functions with self-assembled monolayers

    NARCIS (Netherlands)

    de Boer, B; Hadipour, A; Foekema, R; van Woudenbergh, T; Mandoc, MM; Mihailetchi, VD; Blom, PWM; Heremans, PL; Muccini, M; Hofstraat, H

    2004-01-01

    Tuning the work functions of metals was demonstrated by chemically modifying the metal surface through the formation of chemisorbed self-assembled monolayers (SAMs) derived from 1H,1H,2H,2H-perfluorinated alkanethiols and hexadecanethiol. The ordering inherent in the SAMs creates an effective, molec

  13. Self-assembled monolayers on metal oxides : applications in nanotechnology

    NARCIS (Netherlands)

    Yildirim, O.

    2010-01-01

    The thesis describes the use of phosph(on)ate-based self-assembled monolayers (SAMs) to modify and pattern metal oxides. Metal oxides have interesting electronic and magnetic properties such as insulating, semiconducting, metallic, ferromagnetic etc. and SAMs can tailor the surface properties. FePt

  14. Active control of surface plasmon resonance in MoS2-Ag hybrid nanostructures

    CERN Document Server

    Zu, Shuai; Gong, Yongji; Ajayan, Pulickel M; Fang, Zheyu

    2016-01-01

    Molybdenum disulfide (MoS2) monolayers have attracted much attention for their novel optical properties and efficient light-matter interactions. When excited by incident laser, the optical response of MoS2 monolayers was effectively modified by elementary photo-excited excitons owing to their large exciton binding energy, which can be facilitated for the optical-controllable exciton-plasmon interactions. Inspired by this concept, we experimentally investigated active light control of surface plasmon resonance (SPR) in MoS2-Ag hybrid nanostructures. The white light spectra of SPR were gradually red-shifted by increasing laser power, which was distinctly different from the one of bare Ag nanostructure. This spectroscopic tunability can be further controlled by near-field coupling strength and polarization state of light, and selectively applied to the control of plasmonic dark mode. An analytical Lorentz model for photo-excited excitons induced modulation of MoS2 dielectric function was developed to explain the...

  15. Adsorption of Dibenzothiophene in Acetonitrile on Fe3 +/Cu2 +/Ag+-Modified Activated Carbons with High Specific Surface Area%Fe3+/Cu2+/Ag+改性高比表面活性炭对乙腈中二苯并噻吩的吸附

    Institute of Scientific and Technical Information of China (English)

    李忠; 张红; 夏启斌; 张伟; 余谟鑫

    2013-01-01

    应用浸渍法,采用Fe3+、Cu2+和Ag+对高比表面活性炭(AC)进行改性,制备出3种改性的AC(Fe3 +/AC、Cu2 +/AC和Ag+/AC).采用静态吸附法测定改性AC吸附乙腈溶液中二苯并噻吩(DBT)的吸附等温线,应用程序升温脱附法(TPD)测定DBT在未改性AC及3种改性AC上的脱附峰面积,并采用Boehm滴定法测定这4种吸附剂的表面总酸性基团含量.结果表明:与未改性的AC相比,Fe3+/AC、Cu2+/AC和Ag+/AC表面的总酸性基团含量增加,其对乙腈溶液中DBT的吸附容量也增大;各吸附剂表面的总酸性基团含量顺序为Fea+/AC>Cu2+/AC>Ag+/AC>未改性AC,它们对乙腈溶液中DBT的吸附能力在298K下分别提高了30%、20%、14%.以上结果表明AC类吸附剂的吸附容量与其表面的酸性基团含量成正比;应用浸渍法可提高吸附剂表面的酸性基团含量,从而增加吸附剂表面吸附乙腈溶液中DBT的吸附活性位,提高对DBT的吸附能力.%In this paper, first, activated carbon ( AC) with high specific surface area was modified with metal ions Fe 3+ , Cu1 + and Ag+ through an impregnation process, and three kinds of modified AC, namely, Fe3 + /AC, Cu2 + / AC and Ag + /AC, were prepared. Next, the products were used to adsorb the dibenzothiophene (DBT) in acetonitrile solution, and the corresponding isotherms were obtained by means of the static adsorption method. Then, the desorption peak areas of DBT desorbed from the AC before and after the modification were measured through temperature-programmed desorption (TPD) experiments. Finally, the total amount of acidic functional groups on the surfaces of these four kinds of AC was measured via the Boehm titration. The results show that, after the modification , both the total amount of acidic functional groups and the adsorption capacity for DBT increase, that the total amount of acidic functional groups follows the order of Fe3 + /AC > Cu2 + /AC > Ag+ /AC > AC, with the adsorption capacity

  16. Synthesis, morphological control, and antibacterial properties of hollow/solid Ag2S/Ag heterodimers

    KAUST Repository

    Pang, Maolin

    2010-08-11

    Ag2S and Ag are important functional materials that have received considerable research interest in recent years. In this work, we develop a solution-based synthetic method to combine these two materials into hollow/solid Ag2S/Ag heterodimers at room temperature. Starting from monodisperse Cu2O solid spheres, CuS hollow spheres can be converted from Cu2O through a modified Kirkendall process, and the obtained CuS can then be used as a solid precursor for preparation of the Ag2S/Ag heterodimers through ion exchange and photo-assisted reduction. We have found that formation of the Ag2S/Ag heterodimers is instantaneous, and the size of Ag nanocrystals on the hollow spheres of Ag2S can be controlled by changing the concentration and power of reducing agents in the synthesis. The growth of Ag nanoparticles on hollow spheres of Ag2S in the dimers is along the [111] direction of the silver crystal; the light absorption properties have also been investigated. Furthermore, coupling or tripling of Ag2S/Ag heterodimers into dumbbell-like trimers ((Ag 2S)2/Ag, linear) and triangular tetramers ((Ag 2S)3/Ag, coplanar) can also be attained at 60°C by adding the bidentate ligand ethylenediamine as a cross-linking agent. To test the applicability of this highly asymmetric dipolar composite, photocatalytic inactivation of Escherichia coli K-12 in the presence of the as-prepared Ag 2S/Ag heterodimers has been carried out under UV irradiation. The added Ag2S/Ag heterodimers show good chemical stability under prolonged UV irradiation, and no appreciable solid dissolution is found. Possible mechanisms regarding the enhanced antibacterial activity have also been addressed. © 2010 American Chemical Society.

  17. Pentagonal monolayer crystals of carbon, boron nitride, and silver azide

    Energy Technology Data Exchange (ETDEWEB)

    Yagmurcukardes, M., E-mail: mehmetyagmurcukardes@iyte.edu.tr; Senger, R. T., E-mail: tugrulsenger@iyte.edu.tr [Department of Physics, Izmir Institute of Technology, 35430 Urla, Izmir (Turkey); Sahin, H.; Kang, J.; Torun, E.; Peeters, F. M. [Department of Physics, University of Antwerp, Campus Groenenborgerlaan, 2020, Antwerp (Belgium)

    2015-09-14

    In this study, we present a theoretical investigation of structural, electronic, and mechanical properties of pentagonal monolayers of carbon (p-graphene), boron nitride (p-B{sub 2}N{sub 4} and p-B{sub 4}N{sub 2}), and silver azide (p-AgN{sub 3}) by performing state-of-the-art first principles calculations. Our total energy calculations suggest feasible formation of monolayer crystal structures composed entirely of pentagons. In addition, electronic band dispersion calculations indicate that while p-graphene and p-AgN{sub 3} are semiconductors with indirect bandgaps, p-BN structures display metallic behavior. We also investigate the mechanical properties (in-plane stiffness and the Poisson's ratio) of four different pentagonal structures under uniaxial strain. p-graphene is found to have the highest stiffness value and the corresponding Poisson's ratio is found to be negative. Similarly, p-B{sub 2}N{sub 4} and p-B{sub 4}N{sub 2} have negative Poisson's ratio values. On the other hand, the p-AgN{sub 3} has a large and positive Poisson's ratio. In dynamical stability tests based on calculated phonon spectra of these pentagonal monolayers, we find that only p-graphene and p-B{sub 2}N{sub 4} are stable, but p-AgN{sub 3} and p-B{sub 4}N{sub 2} are vulnerable against vibrational excitations.

  18. Synthesis of one-dimensional silver oxide nanoparticle arrays and silver nanorods templated by Langmuir monolayers.

    Science.gov (United States)

    Liu, Hong-Guo; Xiao, Fei; Wang, Chang-Wei; Xue, Qingbin; Chen, Xiao; Lee, Yong-Ill; Hao, Jingcheng; Jiang, Jianzhuang

    2007-10-01

    One-dimensional (1D) silver oxide nanoparticle arrays were synthesized by illuminating the composite Langmuir-Blodgett monolayers of porphyrin derivatives/Ag(+) and n-hexadecyl dihydrogen phosphate (n-HDP)/Ag(+) deposited on carbon-coated copper grids with daylight and then exposing them to air. Transmission electron microscopy (TEM) observation shows that the nanoparticle size is around 3 nm, with the separation of about 2-3 nm. High-resolution TEM (HRTEM) investigation indicates that the particles are made up of Ag(2)O. Ag nanorods with the width of 15-35 nm and the length of several hundreds of nanometers were synthesized by irradiating the composite Langmuir monolayers of porphyrin derivatives/Ag(+) and n-HDP/Ag(+) by UV-light directly at the air/water interface at room temperature. HRTEM image and selected-area electron diffraction (SAED) pattern indicate that the nanorods are single crystals with the (110) face of the face-centered cubic (fcc) silver parallel to the air/water interface. The formation of the 1D arrays and the nanorods should be attributed to the templating effect of the linear supramolecules formed by porphyrin derivative or n-HDP molecules in Langmuir monolayers through non-covalent interactions.

  19. Application of disorganized monolayer films on gold electrodes to the prevention of surfactant inhibition of the voltammetric detection of trace metals via anodic stripping of underpotential deposits: detection of copper.

    Science.gov (United States)

    Herzog, Grégoire; Arrigan, Damien W M

    2003-01-15

    Development of an approach to prevention of electrode surface fouling by surfactants in samples is demonstrated. Spontaneously adsorbed monolayer systems employing short alkyl chains and bulky end groups are used to form porous disorganized monolayers on gold electrodes. Detection of copper by stripping of underpotential deposits formed at electrodes modified with disorganized films of mercaptoethanesulfonate (MES), mercaptopropanesulfonate, mercaptoacetic acid, and mercaptopropanoic acid was possible, and to a much lesser extent at aminoethanethiol and L-cysteine films. Use of short deposition times in conjunction with linear sweep anodic stripping voltammetry allowed detection of Cu2+ ions down to 1 x 10(-6) M in sulfuric acid solution, using underpotential deposition as the deposition step of the procedure. Calibration graphs were linear in the concentration range (1-80) x 10(-6) M Cu2+ using 15-s deposition at 0.00 V versus Ag/AgCl. The surfactants Tween 20, Tween 80, and Triton X-100 were found to have no affect on detection of Cu2+ ions in the calibration curve concentration range using MES-modified gold electrodes, whereas at unmodified gold electrodes very severe attenuation of the detection capability was manifested. The average slope for all calibration curves at the MES-modified electrode in the absence and presence of the surfactants at two different concentration levels was 0.0710 +/- 0.0024 microA microM(-1); in contrast, the slope of the calibration line at uncoated gold electrodes in the presence of surfactant was 0.0268 microA microM(-1). These results indicate the excellent ability of a disorganized, porous monolayer for prevention of fouling of the electrode surface by the surfactants.

  20. Determination of Caffeine based on Ag-graphene Modified Glassy Carbon Electrode%纳米银-石墨烯修饰玻碳电极检测咖啡因

    Institute of Scientific and Technical Information of China (English)

    徐婧; 臧文玲; 王景宇; 马丽娜; 郭明

    2015-01-01

    Electrochemical sensor for caffeine determination based on a glassy carbon electrode modified with Ag-graphene (Ag-GR/GCE) was fabricated in this paper. Electrochemical behaviors of caffeine on Ag-GR/GCE were investigated by cyclic voltammetry at the voltage range of 0.5~1.7 V. Results showed there was a sensitive oxidative peak at +1.579 V in 0.01 mol/L H2SO4. Under the optimized conditions, the oxidation peak current was linear to the caffeine concentrations in the range of 2×10-6 to 6×10-5mol/L and 6×10-5to 2×10-3mol/L with the detection limit of 6.0×10−7 mol/L(S/N=3). This electrochemical sensor was applied to determined tea samples with satisfactory results.%本文采用化学还原氧化石墨烯的方法制备了纳米银-石墨烯(Ag-GR)复合材料,用此材料制备了纳米银-石墨烯电化学传感器(Ag - GR/GCE),并利用循环伏安法研究了咖啡因的电化学行为。以0.01 mol/L的H2SO4为底液在0.5~1.7 V电压范围,于1.579 V左右有一氧化峰,线性范围为2×10-6~6×10-5mol/L和6×10-5~2×10-3mol/L,检出限( S /N =3)为6×10-7 mol/L。将传感器已用于咖啡因的检测,效果较好。

  1. Monolayer patterning using ketone dipoles.

    Science.gov (United States)

    Kim, Min Kyoung; Xue, Yi; Pašková, Tereza; Zimmt, Matthew B

    2013-08-14

    The self-assembly of multi-component monolayers with designed patterns requires molecular recognition among components. Dipolar interactions have been found to influence morphologies of self-assembled monolayers and can affect molecular recognition functions. Ketone groups have large dipole moments (2.6 D) and are easily incorporated into molecules. The potential of ketone groups for dipolar patterning has been evaluated through synthesis of two 1,5-disubstituted anthracenes bearing mono-ketone side chains, STM characterization of monolayers self-assembled from their single and two component solutions and molecular mechanics simulations to determine their self-assembly energetics. The results reveal that (i) anthracenes bearing self-repulsive mono-ketone side chains assemble in an atypical monolayer morphology that establishes dipolar attraction, instead of repulsion, between ketones in adjacent side chains; (ii) pairs of anthracene molecules whose self-repulsive ketone side chains are dipolar complementary spontaneously assemble compositionally patterned monolayers, in which the two components segregate into neighboring, single component columns, driven by side chain dipolar interactions; (iii) compositionally patterned monolayers also assemble from dipolar complementary anthracene pairs that employ different dipolar groups (ketones or CF2 groups) in their side chains; (iv) the ketone group, with its larger dipole moment and size, provides comparable driving force for patterned monolayer formation to that of the smaller dipole, and smaller size, CF2 group.

  2. The Electrochemical Properties of Thionine Adsorbed Monolayer on Gold Electrode

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A gold electrode modified with adsorbed thionine monolayer was investigated with ac impedance and cyclic voltammetry method. It was found therewere some different redox properties for the adsorbed thionine depended on the different potential scanning rate. At the slower potential scanning rate (10 mV@s-1), the dimer of thionine appeared and possessed the catalytic activity for the oxidation of ascorbic acid.The underpotential deposition (UPD) and the bulk deposition of Cu2+ were also employed to investigate the monolayer of adsorbed thionine.

  3. TiO2-NT electrodes modified with Ag and diamond like carbon (DLC) for hydrogen production by alkaline water electrolysis

    Science.gov (United States)

    Baran, Evrim; Baz, Zeynep; Esen, Ramazan; Yazici Devrim, Birgül

    2017-10-01

    In present work, the two-step anodization technique was applied for synthesis of TiO2 nanotube (NT). Silver and diamond like carbon (DLC) were coated on the surface of as prepared TiO2-NT using chemical reduction method and MW ECR plasma system. The morphology, composition and structure of the electrodes were examined by field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD). The results showed that Ag nanoparticles, having size in the range of 48-115 nm, are evenly distributed on the top, inside and outside surface of TiO2-NT and when DLC was coated on the surface of TiO2-NT and TiO2-NT-Ag, the top of nanotubes were partially open and the pore diameter of hexagonal structure decreased from 165 nm to of 38-80 nm. On the other hand, the microhardness test and contact angle measurements revealed that additions of Ag and diamond like carbon have a positive effect on the mechanical properties of TiO2-NT film. The electrocatalytic properties of the electrodes towards the hydrogen evolution reaction (HER) were investigated by the electrochemical measurements recorded in 1 M KOH solution. In addition, long-term durability of electrodes towards HER and the energy consumption of alkaline electrolysis were investigated. The energy requirement showed that while the deposition of silver provides approximately 14.95% savings of the energy consumption, the DLC coating causes increase in energy consumption.

  4. Thermal Decomposition Based Synthesis of Ag-In-S/ZnS Quantum Dots and Their Chlorotoxin-Modified Micelles for Brain Tumor Cell Targeting

    OpenAIRE

    Chen, Siqi; Ahmadiantehrani, Mojtaba; Publicover, Nelson G.; Hunter, Kenneth W.; Zhu, Xiaoshan

    2015-01-01

    Cadmium-free silver-indium-sulfide (Ag-In-S or AIS) chalcopyrite quantum dots (QDs) as well as their core-shell structures (AIS/ZnS QDs) are being paid significant attention in biomedical applications because of their low toxicity and excellent optical properties. Here we report a simple and safe synthetic system to prepare high quality AIS and AIS/ZnS QDs using thermal decomposition. The synthetic system simply involves heating a mixture of silver acetate, indium acetate, and oleic acid in d...

  5. Phenomenological Modeling for Langmuir Monolayers

    Science.gov (United States)

    Baptiste, Dimitri; Kelly, David; Safford, Twymun; Prayaga, Chandra; Varney, Christopher N.; Wade, Aaron

    Experimentally, Langmuir monolayers have applications in molecular optical, electronic, and sensor devices. Traditionally, Langmuir monolayers are described by a rigid rod model where the rods interact via a Leonard-Jones potential. Here, we propose effective phenomenological models and utilize Monte Carlo simulations to analyze the phase behavior and compare with experimental isotherms. Research reported in this abstract was supported by UWF NIH MARC U-STAR 1T34GM110517-01.

  6. Langmuir monolayers composed of single and double tail sulfobetaine lipids.

    Science.gov (United States)

    Hazell, Gavin; Gee, Anthony P; Arnold, Thomas; Edler, Karen J; Lewis, Simon E

    2016-07-15

    Owing to structural similarities between sulfobetaine lipids and phospholipids it should be possible to form stable Langmuir monolayers from long tail sulfobetaines. By modification of the density of lipid tail group (number of carbon chains) it should also be possible to modulate the two-dimensional phase behaviour of these lipids and thereby compare with that of equivalent phospholipids. Potentially this could enable the use of such lipids for the wide array of applications that currently use phospholipids. The benefit of using sulfobetaine lipids is that they can be synthesised by a one-step reaction from cheap and readily available starting materials and will degrade via different pathways than natural lipids. The molecular architecture of the lipid can be easily modified allowing the design of lipids for specific purposes. In addition the reversal of the charge within the sulfobetaine head group relative to the charge orientation in phospholipids may modify behaviour and thereby allow for novel uses of these surfactants. Stable Langmuir monolayers were formed composed of single and double tailed sulfobetaine lipids. Surface pressure-area isotherm, Brewster Angle Microscopy and X-ray and neutron reflectometry measurements were conducted to measure the two-dimensional phase behaviour and out-of-plane structure of the monolayers as a function of molecular area. Sulfobetaine lipids are able to form stable Langmuir monolayers with two dimensional phase behaviour analogous to that seen for the well-studied phospholipids. Changing the number of carbon tail groups on the lipid from one to two promotes the existence of a liquid condensed phase due to increased Van der Waals interactions between the tail groups. Thus the structure of the monolayers appears to be defined by the relative sizes of the head and tail groups in a predictable way. However, the presence of sub-phase ions has little effect on the monolayer structure, behaviour that is surprisingly different to

  7. Structure and Function Evolution of Thiolate Monolayers on Gold

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, Grant Alvin [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    The use of n-alkanethiolate self-assembled monolayers on gold has blossomed in the past few years. These systems have functioned as models for common interfaces. Thiolate monolayers are ideal because they are easily modified before or after deposition. The works contained within this dissertation include interfacial characterization (inbred reflection absorption spectroscopy, ellipsometry, contact angle, scanning probe microscopy, and heterogeneous electron-transfer kinetics) and various modeling scenarios. The results of these characterizations present ground-breaking insights into the structure, function, and reproducible preparation of these monolayers. Surprisingly, three interfacial properties (electron-transfer, contact angle, and ellipsometry) were discovered to depend directly on the odd-even character of the monolayer components. Molecular modeling was utilized to investigate adlayer orientation, and suggests that these effects are adlayer structure specific. Finally, the electric force microscopy and theoretical modeling investigations of monolayer samples are presented, which show that the film dielectric constant, thickness, and dipole moment directly affect image contrast. In addition, the prospects for utilization of this emerging technique are outlined.

  8. Structure and function evolution of thiolate monolayers on gold

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, Grant Alvin [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    The use of n-alkanethiolate self-assembled monolayers on gold has blossomed in the past few years. These systems have functioned as models for common interfaces. Thiolate monolayers are ideal because they are easily modified before or after deposition. The works contained within this dissertation include interfacial characterization (infrared reflection absorption spectroscopy, ellipsometry, contact angle, scanning probe microscopy, and heterogeneous electron-transfer kinetics) and various modeling scenarios. The results of these characterizations present ground-breaking insights into the structure, function, and reproducible preparation of these monolayers. Surprisingly, three interfacial properties (electron-transfer, contact angle, and ellipsometry) were discovered to depend directly on the odd-even character of the monolayer components. Molecular modeling was utilized to investigate adlayer orientation, and suggests that these effects are adlayer structure specific. Finally, the electric force microscopy and theoretical modeling investigations of monolayer samples are presented, which show that the film dielectric constant, thickness, and dipole moment directly affect image contrast. In addition, the prospects for utilization of this emerging technique are outlined.

  9. SIMULATION ON NONLINEAR OPTICAL ABSORPTION OF BINARY METALS DISPERSED (Au, Ag, Cu)/SiO2 NANO-COMPOSITE FILMS BY MODIFIED MIE THEORY%(Au,Ag,Cu)/SiO2二元金属单分散复合薄膜非线性光吸收性的Mie理论模拟

    Institute of Scientific and Technical Information of China (English)

    严丽平; 张波萍; 王士京; 赵翠华; 李顺

    2011-01-01

    Due to the surface plasmon resonance (SPR) and enhanced local field effect of metal particles, nano-composite films exhibit a variety of properties, such as large third order nonlinear susceptibility, superfast response time and absorption peaks in the optical spectra at a special wavelength. Therefore they are attractive candidates for optical communication, such as information storage and optical device. In recent years, the metal nanoparticle nonlinear optical composite films have been developed rapidly, expanded from single metal nano particle dispersion system to the dual metal nano particle dispersion system. However, theoretical study on the nonlinear optical absorption of the dual metal nano particle dispersion system is quite rare. In this study, the optical absorption spectra of the (Ag, Cu)/SiO2, (Au, Cu)/SiO2 and (Ag, Au)/SiO2 binary metals dispersed nano-composite films were simulated by modified Mie theory. When the metal particles with a low full factor are smaller than the incident wavelength in diameters, the optical spectra of (Ag, Cu)/SiO2, (Au, Cu)/SiO2 and (Ag, Au)/SiO2 composite films in which the nanoparticles solely dispersed in each metal state, can be calculated and analyzed based on the modified Mie theory using the optical parameters of the component. Two SPR absorption peaks appear in the corresponding wavelength of the single metal dispersed nano-composite films.The intensities of SPR absorption peaks depend strongly on the relative content of binary metals,while their peak positions are constant regardless of the content. The calculated optical absorption spectra by proposed method in this study are in good agreement with the reported experiment results.It suggests that the linear superposition method is feasible to calculate the absorption spectra of other separated binary and/or multiplex metals dispersed nano-composite films.%采用修正的Mie理论模拟计算了(Ag,Cu)/SiO2,(Au,Cu)/SiO2和(Ag,Au)/SiO2二元单质金属纳米颗

  10. Orientation of nickelocene on Ag(100)

    Science.gov (United States)

    Pugmire, D. L.; Woodbridge, C. M.; Langell, M. A.

    1998-08-01

    High-resolution electron-energy-loss spectroscopy has been used to study the molecular adsorption of nickelocene, Ni(C 5H 5) 2, on Ag(100). Results indicate that at up to one monolayer coverage, nickelocene adsorbs molecularly with its axis approximately perpendicular to the surface. At very high coverages, the molecular axis is not exclusively oriented along the surface normal. This is possibly due to randomization of the metallocene orientation as multilayers are formed.

  11. Ag antidot array modified TiO2 film and its photocatalysis performance%Ag反点阵列修饰TiO2薄膜的制备及光催化性能研究

    Institute of Scientific and Technical Information of China (English)

    祁洪飞; 刘大博; 成波; 郝维昌; 王天民

    2012-01-01

    采用胶体晶体模板技术和磁控溅射工艺,通过调制溅射功率,制备了一系列不同形貌的Ag反点阵列修饰TiO2复合薄膜.通过扫描电子显微镜(SEM),X射线衍射(XRD),紫外一可见分光光度计(UV-Vis)和四探针测试仪等手段对样品的结构和光催化性能进行了表征.实验结果表明:Ag反点阵列的形貌对样品光催化性能有显著影响.随着反点孔径的减小,其导电性能迅速提升,样品的光催化性能逐渐增强.孔径为710nm时,复合薄膜的光催化性能达到最高.随后,继续减小孔径,样品的光催化性能出现了一定程度的下降,这是载流子损耗增多和遮光面积增大引起的.经Ag反点阵列修饰的样品的光催化性能均明显优于TiO2薄膜,主要是由于反点阵列可有效分离光生载流子,因此使其光催化活性得到显著提高.%Ag antidot arrays modified TiO2 films are obtained by PS colloidal crystal template technique and magnetron sputtering method, and the microstructure of Ag antidot array is modulated through controlling the sputtering power. And then, the structural and the photocatalysis performances of all samples are characterized by using scanning electron microscopy, X-ray diffraction, UV-Vis spec- trophotometer, and four-point probe. The experimental results show that the microstructure of Ag antidot array significantly influences the photocatalysis performance of the sample. With the diameter of the antidot array decreasing, the photocatalysis performance of the sample is enhanced due to the increase of conducting ability. The photocatalysis performance is highest, when the diameter of the anti- dot array is 710 nm. Subsequently, with the diameter of the antidot array further decreasing, the photocatalysis performance decreases to a certain extent, which results from the increases of the carder ioss and the light shading area. The photocatalysis performance of Ag

  12. Nd-doped ZnO monolayer: High Curie temperature and large magnetic moment

    Science.gov (United States)

    Tan, Changlong; Sun, Dan; Zhou, Long; Tian, Xiaohua; Huang, Yuewu

    2016-10-01

    We performed first-principles calculations within density-functional theory to study the structural, electronic, and magnetic properties of Nd-doped ZnO monolayer. The calculated results reveal that Nd-doped ZnO monolayer exhibits stable room temperature ferromagnetism with a large saturation magnetic moment of 3.99 μB per unit in ZnO monolayer. The magnetic property is contributed to the localized f sates of Nd atoms. When two Zn atoms are substituted by two Nd dopants, they tend to form ferromagnetic (FM) coupling and the estimated Curie temperature is higher than room temperature. More interesting, the impurity bands appear within the band gap of ZnO monolayer due to the introduction of Nd dopant. Our results may provide a reference for modifying the material property of ZnO monolayer and are promising as nanoscale building block in spintronic devices.

  13. Thermal Decomposition Based Synthesis of Ag-In-S/ZnS Quantum Dots and Their Chlorotoxin-Modified Micelles for Brain Tumor Cell Targeting.

    Science.gov (United States)

    Chen, Siqi; Ahmadiantehrani, Mojtaba; Publicover, Nelson G; Hunter, Kenneth W; Zhu, Xiaoshan

    Cadmium-free silver-indium-sulfide (Ag-In-S or AIS) chalcopyrite quantum dots (QDs) as well as their core-shell structures (AIS/ZnS QDs) are being paid significant attention in biomedical applications because of their low toxicity and excellent optical properties. Here we report a simple and safe synthetic system to prepare high quality AIS and AIS/ZnS QDs using thermal decomposition. The synthetic system simply involves heating a mixture of silver acetate, indium acetate, and oleic acid in dodecanethiol at 170 °C to produce AIS QDs with a 13% quantum yield (QY). After ZnS shell growth, the produced AIS/ZnS QDs achieve a 41% QY. To facilitate phase transfer and bioconjugation of AIS/ZnS QDs for cellular imaging, these QDs were loaded into the core of PLGA-PEG (5k:5k) based micelles to form AIS/ZnS QD-micelles. Cellular imaging studies showed that chlorotoxin-conjugated QD-micelles can be specifically internalized into U-87 brain tumor cells. This work discloses that the scalable synthesis of AIS/ZnS QDs and the facile surface/interface chemistry for phase transfer and bioconjugation of these QDs may open an avenue for the produced QD-micelles to be applied to the detection of endogenous targets expressed on brain tumor cells, or more broadly to cell- or tissue-based diagnosis and therapy.

  14. Tuning Oleophobicity of Silicon Oxide Surfaces with Mixed Monolayers of Aliphatic and Fluorinated Alcohols.

    Science.gov (United States)

    Lee, Austin W H; Gates, Byron D

    2016-12-13

    We demonstrate the formation of mixed monolayers derived from a microwave-assisted reaction of alcohols with silicon oxide surfaces in order to tune their surface oleophobicity. This simple, rapid method provides an opportunity to precisely tune the constituents of the monolayers. As a demonstration, we sought fluorinated alcohols and aliphatic alcohols as reagents to form monolayers from two distinct constituents for tuning the surface oleophobicity. The first aspect of this study sought to identify a fluorinated alcohol that formed monolayers with a relatively high surface coverage. It was determined that 1H,1H,2H,2H-perfluoro-1-octanol yielded high quality monolayers with a water contact angle (WCA) value of ∼110° and contact angle values of ∼80° with toluene and hexadecane exhibiting both an excellent hydrophobicity and oleophobicity. Tuning of the oleophobicity of the modified silicon oxide surfaces was achieved by controlling the molar ratio of 1H,1H,2H,2H-perfluoro-1-octanol within the reaction mixtures. Surface oleophobicity progressively decreased with a decrease in the fluorinated alcohol content while the monolayers maintained their hydrophobicity with WCA values of ∼110°. The simple and reliable approach to preparing monolayers of a tuned composition that is described in this article can be utilized to control the fluorocarbon content of the hydrophobic monolayers on silicon oxide surfaces.

  15. Improving the dielectric properties of ethylene-glycol alkanethiol self-assembled monolayers.

    Science.gov (United States)

    Zaccari, Irene; Catchpole, Benjamin G; Laurenson, Sophie X; Davies, A Giles; Wälti, Christoph

    2014-02-11

    Self-assembled monolayers (SAMs) can be formed at the interface between solids and fluids, and are often used to modify the surface properties of the solid. One of the most widely employed SAM systems is exploiting thiol-gold chemistry, which, together with alkane-chain-based molecules, provides a reliable way of SAM formation to modify the surface properties of electrodes. Oligo ethylene-glycol (OEG) terminated alkanethiol monolayers have shown excellent antifouling properties and have been used extensively for the coating of biosensor electrodes to minimize nonspecific binding. Here, we report the investigation of the dielectric properties of COOH-capped OEG monolayers and demonstrate a strategy to improve the dielectric properties significantly by mixing the OEG SAM with small concentrations of 11-mercaptoundecanol (MUD). The monolayer properties and composition were characterized by means of impedance spectroscopy, water contact angle, ellipsometry and X-ray photoelectron spectroscopy. An equivalent circuit model is proposed to interpret the EIS data and to determine the conductivity of the monolayer. We find that for increasing MUD concentrations up to about 5% the resistivity of the SAM steadily increases, which together with a considerable decrease of the phase of the impedance, demonstrates significantly improved dielectric properties of the monolayer. Such monolayers will find widespread use in applications which depend critically on good dielectric properties such as capacitive biosensor.

  16. Positional order in Langmuir monolayers

    DEFF Research Database (Denmark)

    Kaganer, V.M.; Brezesinski, G.; Möhwald, H.;

    1998-01-01

    We find that a structural solid-solid phase transition in a two-dimensional Langmuir film is accompanied by strong positional disorder. Specifically, we find by a grazing-incidence x-ray diffraction experiment that in monolayers of octadecanol both the hexagonal phase LS and the centered rectangu......We find that a structural solid-solid phase transition in a two-dimensional Langmuir film is accompanied by strong positional disorder. Specifically, we find by a grazing-incidence x-ray diffraction experiment that in monolayers of octadecanol both the hexagonal phase LS and the centered...

  17. Electromelting of Confined Monolayer Ice

    CERN Document Server

    Qiu, Hu

    2013-01-01

    In sharp contrast to the prevailing view that electric fields promote water freezing, here we show by molecular dynamics simulations that monolayer ice confined between two parallel plates can melt into liquid water under perpendicularly applied electric field. The melting temperature of the monolayer ice decreases with the increasing strength of the external field due to field-induced disruption of the water-wall interaction induced well-ordered network of hydrogen bond. This electromelting process should add an important new ingredient to the physics of water.

  18. Electrodeposition of a Pt monolayer film: using kinetic limitations for atomic layer epitaxy.

    Science.gov (United States)

    Brimaud, Sylvain; Behm, R Jürgen

    2013-08-14

    A new and facile one-step method to prepare a smooth Pt monolayer film on a metallic substrate in the absence of underpotential deposition-type stabilizations is presented as a general approach and applied to the growth of Pt monolayer films on Au. The strongly modified electronic properties of these films were demonstrated by in situ IR spectroscopy at the electrified solid-liquid interface with adsorbed carbon monoxide serving as a probe molecule. The Pt monolayer on Au is kinetically stabilized by adsorbed CO, inhibiting further Pt deposition in higher layers.

  19. 载银纳米TiO2表面改性对抗菌涂料性能的影响%Effects of Surface Modified Nano-TiO2/Ag+ on Properties of Antibacterial Coatings

    Institute of Scientific and Technical Information of China (English)

    周向东; 钟明强

    2011-01-01

    以硅烷偶联剂(KH-570)对纳米TiO2/Ag+进行表面处理,对处理后的纳米TiO2/Ag+进行表征后证实,硅烷偶联剂以化学键的形式键合在纳米TiO2的表面.采用原位乳液聚合方法制得载银纳米TiO2/苯乙烯-丙烯酸酯复合乳液,TEM测试表明纳米TiO2被均匀地包覆在乳液中.采用该复合乳液为基料与各助剂等原料按一定比例配制成涂料,经性能测试后表明,与普通共混制得的涂料相比,该涂料的抗菌性能得到明显的提高,并且有很强的紫外光吸收性能.%Nano-TiO2was modified by γ methacryloxy propyl trimethoxy silane (KH-570). Nano-TiO2/ styrene-acrylic resin composite emulsion was synthesized by in situ emulsion polymerization. Results indicate that KH-570 is covalently bonded to the surface of nano-TiO2 during the modification reaction, which were confirmed by Fourier transform infrared (FT-IR) spectrometry and transmission electron microscopy (TEM). TEM shows that nano-TiO2 is dispersed at nanometer level and distributed uniformly in the composite emulsion. Coatings were prepared by using the composite emulsion as .binder with additives and other materials. Results show that the antibacterial activity of the coatings with modified nano-TiO2 is greatly improved, comparing with the coatings with unmodified nano-TiO2. It also presents perfect UV resistant property.

  20. Applications of self-assembled monolayers in materials chemistry

    Indian Academy of Sciences (India)

    Nirmalya K Chaki; M Aslam; Jadab Sharma; K Vijayamohanan

    2001-10-01

    Self-assembly provides a simple route to organise suitable organic molecules on noble metal and selected nanocluster surfaces by using monolayers of long chain organic molecules with various functionalities like -SH, -COOH, -NH2, silanes etc. These surfaces can be effectively used to build-up interesting nano level architectures. Flexibility with respect to the terminal functionalities of the organic molecules allows the control of the hydrophobicity or hydrophilicity of metal surface, while the selection of length scale can be used to tune the distant-dependent electron transfer behaviour. Organo-inorganic materials tailored in this fashion are extremely important in nanotechnology to construct nanoelctronic devices, sensor arrays, supercapacitors, catalysts, rechargeable power sources etc. by virtue of their size and shape-dependent electrical, optical or magnetic properties. The interesting applications of monolayers and monolayer-protected clusters in materials chemistry are discussed using recent examples of size and shape control of the properties of several metallic and semiconducting nanoparticles. The potential benefits of using these nanostructured systems for molecular electronic components are illustrated using Au and Ag nanoclusters with suitable bifunctional SAMs.

  1. Ubiquitous pentacene monolayer on metals deposited onto pentacene films.

    Science.gov (United States)

    Jaeckel, B; Sambur, J B; Parkinson, B A

    2007-11-01

    Photoelectron spectroscopy (XPS and UPS) was used to study the deposition of metal layers (Ag, Cu, and Au) onto pentacene films. Very low work functions were measured (PhiAg = 3.91 eV, PhiCu = 3.93 eV, and PhiAu = 4.3 eV) for all of the metals, in agreement with results from the literature. The intensities of the C 1s core-level signals from pentacene that were monitored during stepwise metal deposition leveled off at a value of about 30% of a thick pentacene film. This C 1s intensity is comparable to that of one monolayer of pentacene deposited onto the respective metal. The valence band spectra of metals deposited onto pentacene and spectra collected for pentacene deposited onto bare metal surfaces are very similar. These findings lead to the conclusion that approximately one monolayer of pentacene is always present on top of the freshly deposited metal film, which explains the very low work function of the metals when they are deposited onto organic films. We expect similar behavior with other nonreactive metals deposited onto stable organic layers.

  2. Omeprazole decreases magnesium transport across Caco-2 monolayers

    Institute of Scientific and Technical Information of China (English)

    Narongrit Thongon; Nateetip Krishnamra

    2011-01-01

    AIM: To elucidate the effect and underlying mechanisms of omeprazole action on Mg2+ transport across the intestinal epithelium. METHODS: Caco-2 monolayers were cultured in various dose omeprazole-containing media for 14 or 21 d before being inserted into a modified Ussing chamber apparatus to investigate the bi-directional Mg2+ transport and electrical parameters. Paracellular permeability of the monolayer was also observed by the dilution potential technique and a cation permeability study. An Arrhenius plot was performed to elucidate the activation energy of passive Mg2+ transport across the Caco-2 monolayers. RESULTS: Both apical to basolateral and basolateral to apical passive Mg2+ fluxes of omeprazole-treated epithelium were decreased in a dose- and time-dependent manner. Omeprazole also decreased the paracellular cation selectivity and changed the paracellular selective permeability profile of Caco-2 epithelium to Li+, Na+, K+, Rb+, and Cs+ from series Ⅶ to series Ⅵ of the Eisenman sequence. The Arrhenius plot revealed the higher activation energy for passive Mg2+ transport in omeprazoletreated epithelium than that of control epithelium, indicating that omeprazole affected the paracellular channel of Caco-2 epithelium in such a way that Mg2+ movement was impeded. CONCLUSION: Omeprazole decreased paracellular cation permeability and increased the activation energy for passive Mg2+ transport of Caco-2 monolayers that led to the suppression of passive Mg2+ absorption.

  3. Construction of a new selective coated disk electrode for Ag (I) based on modified polypyrrole-carbon nanotubes composite with new lariat ether.

    Science.gov (United States)

    Abbaspour, A; Tashkhourian, J; Ahmadpour, S; Mirahmadi, E; Sharghi, H; Khalifeh, R; Shahriyari, M R

    2014-01-01

    A poly (vinyl chloride) (PVC) matrix membrane ion-selective electrode for silver (I) ion is fabricated based on modified polypyrrole - multiwalled carbon nanotubes composite with new lariat ether. This sensor has a Nernstian slope of 59.4±0.5mV/decade over a wide linear concentration range of 1.0×10(-7) to 1.0×10(-1)molL(-1) for silver (I) ion. It has a short response time of about 8.0s and can be used for at least 50days. The detection limit is 9.3×10(-8)molL(-1) for silver (I) ion, and the electrode was applicable in the wide pH range of 1.6 -7.7. The electrode shows good selectivity for silver ion against many cations such as Hg (II), which usually imposes serious interference in the determination of silver ion concentration. The use of multiwalled carbon nanotubes (MWCNTs) in a polymer matrix improves the linear range and sensitivity of the electrode. In addition by coating the solid contact with a layer of the polypyrrole (Ppy) before coating the membrane on it, not only did it reduce the drift in potential, but a shorter response time was also resulted. The proposed electrode was used as an indicator electrode for potentiometric titration of silver ions with chloride anions and in the titration of mixed halides. This electrode was successfully applied for the determination of silver ions in silver sulphadiazine as a burning cream. © 2013.

  4. L-半胱氨酸修饰Ag-nano-TiO2/CNT复合膜电极的制备及其对苯乙酮的电催化还原%Preparation of L-Cys-Ag-nano-TiO2/CNT Modified Electrode and Its Electrocatalytic Reduction on Hypnone

    Institute of Scientific and Technical Information of China (English)

    张金花; 张莉艳; 褚道葆

    2008-01-01

    在nano-TiO2/CNT电极表面镀一层银,制备了Ag-nano-TiO2/CNT电极.用L-半胱氨酸(L-Cys)修饰Agnano-TiO2/CNT制备了L-Cys-Ag-nano-TiO2/CNT 电极.研究了Ag-nano-TiO2/CNT和L-cys-Ag-nano-TiO2/CNT的电化学性质,结果表明,L-Cys-Ag-nano-TiO2/CNT对苯乙酮有较强的催化还原作用.

  5. Effect of Ag shapes and surface compositions on the photocatalytic performance of Ag/ZnO nanorods

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Jia [Hubei Collaborative Innovation Center for High-efficiency Utilization of Solar Energy, Hubei University of Technology, Wuhan (China); School of Mechanical Engineering, Hubei University of Technology, Wuhan (China); Hubei Provincial Key Laboratory of Green Materials for Light Industry, Hubei University of Technology, Wuhan (China); Wang, Huihu, E-mail: wanghuihu@mail.hbut.edu.cn [Hubei Collaborative Innovation Center for High-efficiency Utilization of Solar Energy, Hubei University of Technology, Wuhan (China); School of Mechanical Engineering, Hubei University of Technology, Wuhan (China); Hubei Provincial Key Laboratory of Green Materials for Light Industry, Hubei University of Technology, Wuhan (China); Dong, Shijie [School of Mechanical Engineering, Hubei University of Technology, Wuhan (China); Hubei Provincial Key Laboratory of Green Materials for Light Industry, Hubei University of Technology, Wuhan (China); Wang, Fanqiang; Dong, Yifan [School of Mechanical Engineering, Hubei University of Technology, Wuhan (China)

    2014-12-25

    Highlights: • Ag/ZnO nanorods were synthesized via photoreduction and hydrothermal methods. • Ag presents nanosheet and nanoparticle shapes in different synthesis methods. • SPR effect and Ag{sup +} is observed only for Ag/ZnO prepared by hydrothermal method. • Ag nanosheets modified ZnO shows the high activity under UV–Vis. irradiation. • Only Ag nanoparticles modified ZnO nanorods has the visible-light-driven activity. - Abstract: Photoreduction and hydrothermal methods were used respectively to prepare Ag surface modified ZnO nanorods in this paper. The surface microstructure and photocatalytic performance of Ag/ZnO nanorods for methyl orange degradation were evaluated in detail. X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS) and UV–Vis. diffuse reflectance spectroscopy (DRS) were used for microstructure analysis of as-prepared Ag/ZnO nanorods. FESEM images showed that Ag presented nanosheets in Ag/ZnO sample (AZP) prepared by photoreduction method, while it exhibited nanoparticles in the sample (AZH) using hydrothermal method. DRS studies clearly displayed surface plasmon resonance (SPR) effect of Ag in AZH samples. Furthermore, there was a red shift on absorption edge for AZH samples compared with bare ZnO and AZP samples. The XPS results revealed that Ag{sup +} ions existed on the surface of AZH samples. In contrast to AZH sample, AZP sample demonstrated the higher photocatalytic activity under UV–Vis. light illumination. However, it was interesting that AZH samples exhibited the visible-light-driven photocatalytic activity, which may be due to the cooperation role of the existence of Ag{sup +} ions and SPR effect of Ag nanoparticles. All these results illustrated that the shapes and surface compositions of Ag may be important factors that influence the photocatalytic performance of Ag/ZnO nanorods. The surface microstructure related photocatalytic mechanism was finally

  6. First-principles study of the contractive reconstruction of gold and silver monolayers on gold, silver and aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, Noboru.

    1990-11-16

    Using first-principles calculations in conjunction with modeling techniques, the author has investigated the structures of Au and Ag monolayers on a number of metal surfaces. Au(100) has a c(26 {times} 68) surface unit cell and the reconstruction has been interpreted as the top layer transforming to a contracted hexagonal-close-packed layer, superimposed on the square lattice of the underlying substrate atoms. Similar reconstructions have been observed on the 5d fcc metals Ir and Pt, but not in the 4d Rh, Pd, and Ag. The author studied the energetics of a monolayer of Au and Ag using first-principles calculations. The author found that it is energetically favorable for both Au and Ag to transform from a square to hexagonal arrangement and to contract to a higher surface density, but Au gains substantially more energy than Ag. This is true both for a monolayer in isolation as well as on top of a jellium surface. The author also calculated the mismatch energy (energy loss when the top layer loses registry with the substrate) for Au and Ag, and found that Ag has a slightly higher mismatch energy. The first-principles results thus offer a strong indication that Au(100) can reconstruct but Ag will not. The reconstruction is further studied with a 2 dimensional Frenkel-Kontorowa model, with parameters extracted from the total energy calculations. The author found that it is indeed energetically favorable for the top layer of Au(100), but not for Ag, to transform to a hexagonal-close-packed structure and contract. 85 refs., 34 figs., 8 tabs.

  7. Influence of the Au/Ag ratio on the catalytic activity of dendrimer-encapsulated bimetallic nanoparticles in microreactors

    NARCIS (Netherlands)

    Ricciardi, R.; Huskens, J.; Verboom, W.

    2015-01-01

    Dendrimer-encapsulated Au/Ag alloy nanoparticles (Au/Ag DENs) were covalently attached to a monolayer-functionalized inner surface of glass microreactors. The influence of the bimetallic alloy structure and of the different metal ratios was investigated for the reduction of 4-nitrophenol using NaBH4

  8. Influence of the Au/Ag ratio on the catalytic activity of dendrimer-encapsulated bimetallic nanoparticles in microreactors

    NARCIS (Netherlands)

    Ricciardi, R.; Huskens, Jurriaan; Verboom, Willem

    2015-01-01

    Dendrimer-encapsulated Au/Ag alloy nanoparticles (Au/Ag DENs) were covalently attached to a monolayer-functionalized inner surface of glass microreactors. The influence of the bimetallic alloy structure and of the different metal ratios was investigated for the reduction of 4-nitrophenol using

  9. Multifunctional Self-Assembled Monolayers for Organic Field-Effect Transistors

    Science.gov (United States)

    Cernetic, Nathan

    Organic field effect transistors (OFETs) have the potential to reach commercialization for a wide variety of applications such as active matrix display circuitry, chemical and biological sensing, radio-frequency identification devices and flexible electronics. In order to be commercially competitive with already at-market amorphous silicon devices, OFETs need to approach similar performance levels. Significant progress has been made in developing high performance organic semiconductors and dielectric materials. Additionally, a common route to improve the performance metric of OFETs is via interface modification at the critical dielectric/semiconductor and electrode/semiconductor interface which often play a significant role in charge transport properties. These metal oxide interfaces are typically modified with rationally designed multifunctional self-assembled monolayers. As means toward improving the performance metrics of OFETs, rationally designed multifunctional self-assembled monolayers are used to explore the relationship between surface energy, SAM order, and SAM dipole on OFET performance. The studies presented within are (1) development of a multifunctional SAM capable of simultaneously modifying dielectric and metal surface while maintaining compatibility with solution processed techniques (2) exploration of the relationship between SAM dipole and anchor group on graphene transistors, and (3) development of self-assembled monolayer field-effect transistor in which the traditional thick organic semiconductor is replaced by a rationally designed self-assembled monolayer semiconductor. The findings presented within represent advancement in the understanding of the influence of self-assembled monolayers on OFETs as well as progress towards rationally designed monolayer transistors.

  10. Photopatterning of self-assembled alkanethiolate monolayers on gold. A simple monolayer photoresist utilizing aqueous chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Huang, J.; Hemminger, J.C. (Univ. of California, Irvine, CA (United States)); Dahlgren, D.A. (Photometrics, Huntington Beach, CA (United States))

    1994-03-01

    In this paper we demonstrate that self-assembled monolayers (SAMs) of alkanethiols on gold can be used as effective photoresists. UV photolysis of an alkanethiol SAM generates the corresponding sulfonate in the monolayer film. The sulfonate is easily rinsed off of the surface with water, exposing a clean gold substrate, which can then be modified with subsequent chemistry. We describe here experiments in which an alkanethiol SAM on a gold film on silicon is irradiated through a mask, followed by immersion of the sample in an aqueous acid etching solution (HCI:HNO[sub 3]:H[sub 2]O = 3:1:4). The gold is etched away from the areas which have been exposed to UV radiation leaving a pattern which reproduces the original mask. The spatial resolution in the present experiments is limited by the mask which is a 6-[mu]m wire grid. Scanning electron microscopy images of patterned samples show sharp edges to the features suggesting that spatial patterning on the 1-[mu]m scale should be attainable with this simple chemistry. 11 refs., 4 figs.

  11. Aminopropyltrimethoxysilane- and aminopropyltrimethoxysilane-silver-modified montmorillonite for the removal of nitrate ions.

    Science.gov (United States)

    Gatti, Marcela N; Fernández, Laura G; Sánchez, María P; Parolo, M Eugenia

    2016-10-01

    A natural clay (Mn) modified with γ-aminopropyltrimethoxysilane (Mn-S) and silver (Mn-S-Ag) were evaluated as a potential adsorption media for nitrate removal from water. These materials were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, zeta-potential, thermogravimetric analysis, scanning electron microscopy and elemental analyses. First, the adsorption capacity of the Mn-S clay for Ag(+) was studied. The cation adsorption capacity was almost three times greater for Mn-S than for Mn because a metal-amino group complex is favored. Second, the nitrate adsorption on Mn-S and Mn-S-Ag was studied as a function of contact time, pH, temperature and adsorbent dosage using batch techniques. In the absence of Ag(+), [Formula: see text] adsorption was high at low pH and the amount of adsorbed nitrate decreased as the pH increased. For the Mn-S, the following monolayer adsorption capacities were obtained: Qmax = 0.80, 0.72 and 0.68 mmol [Formula: see text]/g at pH 3, 5 and 7, respectively, whereas for the Mn-S-Ag the values obtained were: Qmax = 0.77, 0.74 and 0.42 mmol [Formula: see text]/g at pH 3, 5 and 7, respectively. From the results obtained, [Formula: see text] adsorption occurs over [Formula: see text] surface groups without involving the Ag(+) cation in the adsorption process.

  12. Electronic and Magnetic Properties of Rare-Earth Metals Doped ZnO Monolayer

    Directory of Open Access Journals (Sweden)

    Changlong Tan

    2015-01-01

    Full Text Available The structural, electronic, and magnetic properties of rare-earth metals doped ZnO monolayer have been investigated using the first-principles calculations. The induced spin polarization is confirmed for Ce, Eu, Gd, and Dy dopings while the induced spin polarization is negligible for Y doping. The localized f states of rare-earth atoms respond to the introduction of a magnetic moment. ZnO monolayer undergoes transition from semiconductor to metal in the presence of Y, Ce, Gd, and Dy doping. More interestingly, Eu doped ZnO monolayer exhibits half-metallic behavior. Our result demonstrates that the RE-doping is an efficient route to modify the magnetic and electronic properties in ZnO monolayer.

  13. Self-assembling Process of Alkanethiol Monolayers on Gold Surface via Underpotential Deposition

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    It was demonstrated feasible that underpotential deposition(UPD) of copper on a monolayer-modified gold substrate can be used to determine the gold electrode area. The deposition and stripping of a Cu adlayer can take place reversibly and stably at a bared or a self-assembled monolayer modified gold electrode. The growth kinetics of decanethiol/Au was also investigated via Cu UPD. The difference between the assembling kinetics determined by UPD and that by quartz crystal microbalance measurements reveals the configuration transmutation of the assembled molecules from a disordered arrangement to an ordered arrangement during the self-assembling processes.

  14. Comparative Study of Protein Immobilization Properties on Calixarene Monolayers

    Directory of Open Access Journals (Sweden)

    Kwangnak Koh

    2007-06-01

    Full Text Available Three calix[4]arene (Cal-4 derivatives of which contain ethylester (1,carboxylic acid (2, and crownether (3 at the lower rim with a common reactive thiol at theupper rim were synthesized and constructed to self-assembled monolayers (SAMs on Aufilms. After spectroscopic characterization of monolayers, the interaction between Cal-4and surface confined bovine serum albumin (BSA in the SAMs was analyzed by surfaceplasmon resonance (SPR. The estimated surface concentration of BSA on the Cal-4 SAMwith crownether group was the highest among the three Cal-4 derivatives. Anti-hIgG andhIgG pair was employed for the investigation of protein-protein interaction. Molecularinteraction between anti-hIgG and hIgG can be detected in a concentration range of 10pg/mL to 200 pg/mL on the Cal-4 derivative 3 SAM modified SPR chip.

  15. Facile synthesis of ternary Ag/AgBr-Ag{sub 2}CO{sub 3} hybrids with enhanced photocatalytic removal of elemental mercury driven by visible light

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Anchao, E-mail: anchaozhang@126.com [School of Mechanical and Power Engineering, Henan Polytechnic University, Jiaozuo, 454000 (China); Zhang, Lixiang; Lu, Hao; Chen, Guoyan; Liu, Zhichao [School of Mechanical and Power Engineering, Henan Polytechnic University, Jiaozuo, 454000 (China); Xiang, Jun; Sun, Lushi [State Key Laboratory of Coal Combustion, Huazhong University of Science and Technology, Wuhan, 430074 (China)

    2016-08-15

    Graphical abstract: Schematic illustration for the charge transfer in the Ag/AgBr(0.7)-Ag{sub 2}CO{sub 3} system. - Highlights: • A novel technique on Hg{sup 0} removal using visible-light-driven Ag/AgBr-Ag{sub 2}CO{sub 3} hybrids was proposed. • Ag/AgBr-Ag{sub 2}CO{sub 3} hybrids were synthesized by a simple modified co-precipitation method. • Hg{sup 0} was mainly removed by the photogenerated holes (h{sup +}). • The possible reaction mechanism for superior Hg{sup 0} removal was proposed. - Abstract: A novel technique for photocatalytic removal of elemental mercury (Hg{sup 0}) using visible-light-driven Ag/AgBr-Ag{sub 2}CO{sub 3} hybrids was proposed. The ternary Ag/AgBr-Ag{sub 2}CO{sub 3} hybrids were synthesized by a simple modified co-precipitation method and characterized by N{sub 2} adsorption-desorption, scanning electron microscope (SEM), X-ray diffraction (XRD), UV–vis diffused reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS) and electron spin resonance (ESR) techniques. The effects of AgBr content, fluorescent lamp (FSL) irradiation, solution temperature, SO{sub 2} and NO on Hg{sup 0} removal were investigated in detail. Furthermore, a possible reaction mechanism for higher Hg{sup 0} removal was proposed, and the simultaneous removal of Hg{sup 0}, SO{sub 2} and NO was studied. The results showed that a high efficiency of Hg{sup 0} removal was obtained by using Ag/AgBr-Ag{sub 2}CO{sub 3} hybrids under fluorescent lamp irradiation. The AgBr content, FSL irradiation, solution temperature, and SO{sub 2} all exhibited significant effects on Hg{sup 0} removal, while NO had slight effect on Hg{sup 0} removal. The addition of Ca(OH){sub 2} demonstrated a little impact on Hg{sup 0} removal and could significantly improve the SO{sub 2}-resistance performance of Ag/AgBr(0.7)-Ag{sub 2}CO{sub 3} hybrid. The characterization results exhibited that hydroxyl radical (·OH), superoxide radical (·O{sub 2}{sup −}), hole (h{sup +}), and Br

  16. Electrocatalytic oxidation of GMP on an ITO electrode modified by the photoposition of Pd nanoparticles onto a monolayer TiO2-Ru(Ⅱ)complex hybrid film%Pd纳米粒子敏化的纳米单层TiO2-Ru(Ⅱ)螯合物修饰电极对单磷酸鸟苷的电催化氧化行为

    Institute of Scientific and Technical Information of China (English)

    陈锡安; 王舜; 林娟娟; 刘爱丽; 黄少铭

    2011-01-01

    利用LB膜技术可控制备了纳米单层的二氧化钛-有机钌螯合物杂化膜,并研究了上述无机-有机杂化膜修饰电极在Pd纳米粒子敏化后对单磷酸鸟苷(GMP)的电催化氧化行为.实验结果表明:(1)纳米单层TiO2/[Ru(phen)2(dC18bpy)]2+(简称为TiO2-Ru)杂化膜的平均厚度为(3.2±0.5)nm;(2)在光照条件下TiO2-Ru杂化膜能有效催化还原[Pd(NH3)4]2+形成粒径位于20~200 nm之间的Pd纳米粒子;(3)纳米单层TiO2-Ru/Pd杂化膜能高效催化氧化具有供电子能力的单磷酸鸟苷(GMP),与纳米单层TiO2-Ru杂化膜修饰的ITO电极(ITO/TiO2-Ru)相比,当工作电压为1200mV时,ITO/TiO2-Ru/Pd电极在含有1×10-3 mol L-1 GMP的磷酸盐缓冲液中,单位面积的催化氧化电流提高了约36倍;(4)Pd纳米粒子的引入消除了金属钌螯合物中配体对电子传递的阻碍作用,改变了电子传递途径,从而有效减少了电子空穴对的复合,提高了杂化膜修饰电极(ITO/TiO2-Ru/Pd)的电子传递效率.%An indium tin oxide (ITO) electrode coated with monolayer TiO2/[Ru(phen)2(dC18bpy)]2+ (phen =1,10-phenanthroline, dC18bpy = 4,4'-dioctadecyl-2,2'-bipyridyl) hybrid film (denoted as ITO/TiO2-Ru) has been prepared by the modified Langmuir-Blodgctt (LB) method, and the electrocatalytic oxidation of mononuclcotide of guanosine 5'-monophosphate (GMP) on an ITO/TiO2-Ru electrode after Pd-photodeposition (denoted as ITO/TiO2-Ru/Pd) has been studied.Atomic force microscopy reveals that the single-layered hybrid film of TiO2 nanosheets/[Ru(phen)2(dCl 8bpy)]2+ is closely packed at a surface pressure of 25 mN m-1 and has a thickness of (3.20 ± 0.5) nm.X-ray photoelectron spectra shows the formation of Pd nanoparticlcs on the surface of hybrid film with radii of 20~200 nm by the reduction of [Pd(NH3)4]2+ under light irradiation.When being applied to oxidize GMP, a larger catalytic oxidative current is achieved on thc ITO/TiO2-Ru/Pd electrode at the external potential above 700 m

  17. Packing of ganglioside-phospholipid monolayers

    DEFF Research Database (Denmark)

    Majewski, J.; Kuhl, T.L.; Kjær, K.

    2001-01-01

    DPPE monolayer and does not distort the hexagonal in-plane unit cell or out-of-plane two-dimensional (2-D) packing compared with a pure DPPE monolayer. The oligosaccharide headgroups were found to extend normally from the monolayer surface, and the incorporation of these glycolipids into DPPE...... monolayers did not affect hydrocarbon tail packing (fluidization or condensation of the hydrocarbon region). This is in contrast to previous investigations of lipopolymer-lipid mixtures, where the packing structure of phospholipid monolayers was greatly altered by the inclusion of lipids bearing hydrophilic...... polymer groups. Indeed, the lack of packing disruptions by the oligosaccharide groups indicates that protein-GM, interactions, including binding, insertion, chain fluidization, and domain formation (lipid rafts), can be studied in 2-D monolayers using scattering techniques....

  18. Modeling Stimuli-Responsive Nanoparticle Monolayer

    Science.gov (United States)

    Yong, Xin

    2015-03-01

    Using dissipative particle dynamics (DPD), we model a monolayer formed at the water-oil interface, which comprises stimuli-responsive nanoparticles. The solid core of the nanoparticle encompasses beads arranged in an fcc lattice structure and its surface is uniformly grafted with stimuli-responsive polymer chains. The surface-active nanoparticles adsorb to the interface from the suspension to minimize total energy of the system and create a monolayer covering the interface. We investigate the monolayer formation by characterizing the detailed adsorption kinetics. We explore the microstructure of the monolayer at different surface coverage, including the particle crowding and ordering, and elucidate the response of monolayer to external stimuli. The collective behavior of the particles within the monolayer is demonstrated quantitatively by vector-vector autocorrelation functions. This study provides a fundamental understanding of the interfacial behavior of stimuli-responsive nanoparticles.

  19. Ag on a Ni vicinal surface: Coupling Stranski-Krastanov and "magic" heteroepitaxial growth

    Science.gov (United States)

    Bellec, Amandine; Garreau, Yves; Creuze, Jérôme; Vlad, Alina; Picca, Frederic; Sauvage-Simkin, Michèle; Coati, Alessandro

    2017-08-01

    Using vicinal surfaces as a template for heteroepitaxial growth offers a unique possibility to control the orientation and the crystallinity of the grown layer. The study presented here focuses on the growth of Ag on a carefully chosen Ni(11 9 9) substrate. Ag adopts a Stranski-Krastanov growth mode with a slightly constrained wetting layer limited to two monolayers on which well crystallized islands grow. The specific orientation of the Ni substrate leads to Ag(7 9 9) orientation for the Ag thin film and it prevents the formation of twin and stacking fault.

  20. Large-scale growth and characterizations of nitrogen-doped monolayer graphene sheets.

    Science.gov (United States)

    Jin, Zhong; Yao, Jun; Kittrell, Carter; Tour, James M

    2011-05-24

    In-plane heteroatom substitution of graphene is a promising strategy to modify its properties. Doping with electron-donor nitrogen heteroatoms can modulate the electronic properties of graphene to produce an n-type semiconductor. Here we demonstrate the growth of monolayer nitrogen-doped graphene in centimeter-scale sheets using a chemical vapor deposition process with pyridine as the sole source of both carbon and nitrogen. High-resolution transmission microscopy and Raman mapping characterizations indicate that the nitrogen-doped graphene sheets are uniformly monolayered. The existence of nitrogen-atom substitution in the graphene planes was confirmed by X-ray photoelectron spectroscopy. Electrical measurements show that the nitrogen-doped graphene exhibits an n-type behavior, different from pristine graphene. The preparation of large-area nitrogen-doped graphene provides a viable route to modify the properties of monolayer graphene and promote its applications in electronic devices.

  1. Effect of Ag+ and PO43- ratios on the microstructure and photocatalytic activity of Ag3PO4

    Science.gov (United States)

    Qin, Jiaqian; Zhang, Xinyu; Yang, Chengwu; Song, Aijun; Zhang, Bing; Rajendran, Saravanan; Ma, Mingzhen; Liu, Riping

    2016-09-01

    In this work, the catalyst silver phosphate (Ag3PO4) with different initial ratios of Ag+ and PO43- in aqueous solution was synthesized by a simple precipitation method from AgNO3 and NH4H2PO4 which were used as the precursor. After that, the prepared samples were characterized by different techniques such as field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), UV-visible diffuse reflectance spectroscopy (UV-DRS) and decomposition evolution of rhodamine B (RhB) solution. The results indicate that the initial ratios of Ag+/PO43- in aqueous solution can modify the morphology and also it can significantly affect the photocatalytic performance. During photocatalytic process, the rich Ag+ ion Ag3PO4 can form the surface plasmon resonance (SPR) of Ag nanoparticles, which inhibit the reduction of Ag3PO4 resulting in higher photocatalytic activity and stability.

  2. Magnetic monolayers on semiconducting substrates. An in situ FMR study of Fe-based heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Zakeri Lori, K.

    2007-10-18

    The growth, magnetic anisotropy, g-factor, and magnetization of Fe monolayers grown on GaAs(001), InAs(001), and InP(001) are investigated by a combination of in situ ferromagnetic resonance and SQUID magnetometry as a function of temperature and film thickness. The effect of stress caused by the lattice mismatch and the surface reconstruction on the magnetic anisotropy is quantified. An in-plane spin reorientation transition as a function of film thickness is observed at room temperature for all systems. A magneto-elastic model is used to explain the direction of the easy axis, the spin reorientation transition, and the contributions to the magnetic anisotropy terms using the stress components measured directly by in situ IV-low-energy electron diffraction. While the model gives a quantitative explanation of the out-of-plane magnetic anisotropy, changes of the electronic interface structure have to be taken into account for the in-plane magnetic anisotropy. The influence of Ag and Au buffer and cap layers on the magnetic anisotropy terms are determined. The temperature dependence of the total magnetic anisotropy, as well as the surface-interface and volume contribution to the magnetic anisotropy are determined for Fe monolayers on GaAs(001). It is demonstrated that the temperature dependence of the magnetic anisotropy is correlated with the temperature dependence of the magnetization according to the Callen-Callen model. The temperature dependence of the volume contribution to the perpendicular magnetic anisotropy is fully explained by the temperature dependence of the magneto-elastic anisotropy. A temperature-driven morphological transformation occurring at a temperature higher than 550 K depending on the film thickness is observed. The thin Fe3Si binary Heusler structure epitaxially grown on MgO(001) is investigated. In addition to the structural properties, magnetic anisotropy, magnetization, g-factor, spin, and orbital magnetism, the magnetic relaxation

  3. Self-assembled biomimetic monolayers using phospholipid-containing disulfides.

    Science.gov (United States)

    Chung, Yi Chang; Chiu, Yi Hong; Wu, Yin Wei; Tao, Yu Tai

    2005-05-01

    Several phospholipid-based disulfide molecules were synthesized and attached onto the gold-coated silicon wafer using the self-assembling method. The syntheses of these surface-modifying agents were conducted by introducing bromoethylphosphorate (PBr), phosphorylcholine (PC) or phosphorylethanolamine (PE) groups on the terminals of a dialkyl disulfide. After disulfides adsorption onto gold substrate surfaces, the composition, the film thickness, and the conformational order of self-assembled monolayer surfaces were explored and discussed in detail based on reflection-absorption infrared spectroscopy, contact angle measurement, Auger electron spectroscopy, X-ray photoelectron spectroscopy, and so on. The monolayer having the PBr end group could also be converted to a PC surface by treating with trimethylamine. The model functional surfaces of Au-SC11-PC, -PE, -PBr, -OH or corresponding mixed layers were used to mimic biomembrane surfaces. The monolayer having PC groups was found to reduce fibrinogen adsorption as evaluated from protein adsorption experiments using quartz crystal microbalance. It also showed relatively low platelet adherence compare to the glass, PBr and PE surfaces. The cell viability test also revealed that the PC surface displayed lower cytotoxicity than other surfaces.

  4. Strain Tuning of the Charge Density Wave in Monolayer and Bilayer 1T-TaS2

    KAUST Repository

    Gan, Liyong

    2015-12-07

    By first-principles calculations, we investigate the strain effects on the charge density wave states of monolayer and bilayer 1T-TaS2. The modified stability of the charge density wave in the monolayer is understood in terms of the strain dependent electron localization, which determines the distortion amplitude. On the other hand, in the bilayer the effect of strain on the interlayer interaction is also crucial. The rich phase diagram under strain opens new venues for applications of 1T-TaS2. We interpret the experimentally observed insulating state of bulk 1T-TaS2 as inherited from the monolayer by effective interlayer decoupling.

  5. Lateral pressure profiles in lipid monolayers

    NARCIS (Netherlands)

    Baoukina, Svetlana; Marrink, Siewert J.; Tieleman, D. Peter

    2010-01-01

    We have used molecular dynamics simulations with coarse-grained and atomistic models to study the lateral pressure profiles in lipid monolayers. We first consider simple oil/air and oil/water interfaces, and then proceed to lipid monolayers at air/water and oil/water interfaces. The results are qual

  6. "Living" free radical photopolymerization initiated from surface-grafted iniferter monolayers

    NARCIS (Netherlands)

    de Boer, B.; Simon, H.K.; Werts, M.P L; van der Vegte, E.W.; Hadziioannou, G

    2000-01-01

    A method for chemically modifying a surface with grafted monolayers of initiator groups, which can be used for a "living" free radical photopolymerization, is described. By using "living" free radical polymerizations, we were able to control the length of the grafted polymer chains and therefore the

  7. UV/Vis and NIR Light-Responsive Spiropyran Self-Assembled Monolayers

    NARCIS (Netherlands)

    Ivashenko, Oleksii; Herpt, Jochem T. van; Feringa, Ben L.; Rudolf, Petra; Browne, Wesley R.

    2013-01-01

    Self-assembled monolayers of a 6-nitro BIPS spiropyran (SP) modified with a disulfide-terminated aliphatic chain were prepared on polycrystalline gold surfaces and characterized by UV/vis absorption, surface-enhanced Raman scattering (SEAS), and X-ray photoelectron spectroscopies (XPS). The SAMs

  8. UV/Vis and NIR Light-Responsive Spiropyran Self-Assembled Monolayers

    NARCIS (Netherlands)

    Ivashenko, Oleksii; Herpt, Jochem T. van; Feringa, Ben L.; Rudolf, Petra; Browne, Wesley R.

    2013-01-01

    Self-assembled monolayers of a 6-nitro BIPS spiropyran (SP) modified with a disulfide-terminated aliphatic chain were prepared on polycrystalline gold surfaces and characterized by UV/vis absorption, surface-enhanced Raman scattering (SEAS), and X-ray photoelectron spectroscopies (XPS). The SAMs obt

  9. Self-assembled monolayers with biospecific affinity for lactate dehydrogenase for the electroenzymatic oxidation of lactate

    NARCIS (Netherlands)

    Schlereth, Daniela D.; Kooyman, R.P.H.

    1997-01-01

    Surface modified gold electrodes with high biospecific affinity for NAD(H)-dependent lactate dehydrogenase have been prepared by covalent attachment of several traizine dyes to stepwise functionalized mixed alkanethiol self-assembled monolayers. The biospecific affinity of such ligand-anchored

  10. Binary functionalization of H:Si(111) surfaces by alkyl monolayers with different linker atoms enhances monolayer stability and packing.

    Science.gov (United States)

    Arefi, Hadi H; Nolan, Michael; Fagas, Giorgos

    2016-05-14

    Alkyl monolayer modified Si forms a class of inorganic-organic hybrid materials with applications across many technologies such as thin-films, fuel/solar-cells and biosensors. Previous studies have shown that the linker atom, through which the monolayer binds to the Si substrate, and any tail group in the alkyl chain, can tune the monolayer stability and electronic properties. In this paper we study the H:Si(111) surface functionalized with binary SAMs: these are composed of alkyl chains that are linked to the surface by two different linker groups. Aiming to enhance SAM stability and increase coverage over singly functionalized Si, we examine with density functional theory simulations that incorporate vdW interactions, a range of linker groups which we denote as -X-(alkyl) with X = CH2, O(H), S(H) or NH(2) (alkyl = C6 and C12 chains). We show how the stability of the SAM can be enhanced by adsorbing alkyl chains with two different linkers, e.g. Si-[C, NH]-alkyl, through which the adsorption energy is increased compared to functionalization with the individual -X-alkyl chains. Our results show that it is possible to improve stability and optimum coverage of alkyl functionalized SAMs linked through a direct Si-C bond by incorporating alkyl chains linked to Si through a different linker group, while preserving the interface electronic structure that determines key electronic properties. This is important since any enhancement in stability and coverage to give more densely packed monolayers will result in fewer defects. We also show that the work function can be tuned within the interval of 3.65-4.94 eV (4.55 eV for bare H:Si(111)).

  11. Self-assembled monolayers applications for the development of electrochemical sensors

    OpenAIRE

    Renato S. Freire; Pessoa, Christiana A.; Lauro T. Kubota

    2003-01-01

    Self-assembled monolayers (SAMs) modified electrodes exhibit unique behavior that can greatly benefit electrochemical sensing. This brief review highlights the applications of SAM modified electrodes in electroanalytical chemistry. After a general introduction, which includes the approaches for SAM development, different electrochemical systems for detecting inorganic and organic species are described and discussed. Special attention to the coupling of biological sensing element to the SAM is...

  12. Coulomb excitations of monolayer germanene

    Science.gov (United States)

    Shih, Po-Hsin; Chiu, Yu-Huang; Wu, Jhao-Ying; Shyu, Feng-Lin; Lin, Ming-Fa

    2017-01-01

    The feature-rich electronic excitations of monolayer germanene lie in the significant spin-orbit coupling and the buckled structure. The collective and single-particle excitations are diversified by the magnitude and direction of transferred momentum, the Fermi energy and the gate voltage. There are four kinds of plasmon modes, according to the unique frequency- and momentum-dependent phase diagrams. They behave as two-dimensional acoustic modes at long wavelength. However, for the larger momenta, they might change into another kind of undamped plasmons, become the seriously suppressed modes in the heavy intraband e–h excitations, keep the same undamped plasmons, or decline and then vanish in the strong interband e–h excitations. Germanene, silicene and graphene are quite different from one another in the main features of the diverse plasmon modes. PMID:28091555

  13. Photocatalytic Activity of Ag-TiO2 Thin Films by Two Different Modified Methods%两种不同改性方法制备的Ag-TiO2薄膜光催化活性研究

    Institute of Scientific and Technical Information of China (English)

    白亮; 任学昌; 魏雪芬; 李保成; 马学琴

    2011-01-01

    以溶胶凝胶法在平板玻璃表面负载了TiO2薄膜,用不同浓度AgNO3溶液浸渍,然后进行了光照还原法和煅烧分解法Ag改性.以甲醛为模拟污染物,考察了两种方法改性的Ag-TiO2薄膜的光催化活性.结果表明:光照还原法在AgNO3溶液为0.1 moL/L时Ag改性的TiO2薄膜催化活性最强,其催化活性是纯TiC2薄膜的2.3倍;煅烧分解法AgNO3溶液为0.05 moL/L时Ag改性的TiO2薄膜催化活性最强,其催化活性是纯TiO2薄膜的2.9;分析了两种不同改性方法提高TiO2薄膜催化活性的机理.%Ag-TiO2 thin films were prepared as follows :TiO2 thin films were prepared using sol-gel method and subsequently dipped in AgNO3 solution, then they were illuminated and calcined, respectively. The pho-tocatalytic activity of Ag-TiO2 thin films was tested using phenol degradation as the model reaction. The results indicated that when the concentration of AgNO3 solution was 0. 1 moL/L,the photocatalytic activity of the photodeposited Ag-TiO2 thin films was 2. 3 times of that of pure TiO2 thin films,when the concentration of AgNC>3 solution was 0. 05 moL/L,the photocatalytic activity of the calcined Ag-TiO2 thin films was 2. 9 times of that of pure TiO2 thin films. The mechanism of two modification methods to improve activity of TiO2 thin films were analyzed.

  14. Electrocatalytic oxidation of simvastatin at SDBS self-assembled monolayers and RGO modified carbon paste electrode and its electrochemical determination%SMV 在 SDBS 自组装膜与 RGO 复合修饰碳糊电极上的电催化氧化及电分析研究

    Institute of Scientific and Technical Information of China (English)

    张瑞; 张青春; 段春玲; 彭娟; 高作宁

    2013-01-01

    Electrocatalytic oxidation and electrochemical kinetics of simvastatin ( SMV) were investigated at sodium dodecyl benzene-sulfonate(SDBS)self-assembled monolayers and graphene (RGO)modified carbon paste electrode(SDBS-RGO/CPE).The experi-mental results showed that SDBS-RGO/CPE showed an excellent electrocatalytic activity towards SMV electrochemical oxida -tion.The electrochemical kinetic parameters were also determined by cyclic voltammetry ( CV) and chronoamperometry ( CA).The oxidation peak current of catalytic oxidation of SMV versus its concentration had a good linear relationship in the concentration range of 6.0 ×10-5 mol· L-1 ~4.5 ×10-4 mol· L-1 and the detection limit of 5.0 ×10-6 mol· L-1 ( S/N=3 ) by square wave voltammetry ( SWV).At the same time the supposed method have been applied in the electrochemical quantitative determination of SMV content in commercial tablet samples and the determination results meet the requirement of the quantitative determination .%研究了辛伐他汀(SMV)在表面活性剂十二烷基苯磺酸钠(SDBS)自组装膜与石墨烯(RGO)复合修饰碳糊电极(SDBS-RGO/CPE)上的电催化氧化和电化学动力学性质。实验结果表明,SDBS-RGO/CPE对SMV电化学氧化具有良好的催化作用。同时用循环伏安法(CV),计时电流法(CA)测定了SMV在SDBS-RGO/CPE上的电极反应动力学参数,用方波伏安法( SWV)测得SMV氧化峰电流( Ipa )与其浓度在6.0×10-5~4.5×10-4mol· L-1范围内呈良好线性关系,检测限(S/N=3)为5.0×10-6mol· L-1,同时运用该方法对市售辛伐他汀片剂中SMV含量进行了电化学定量测定,测定结果符合定量测定要求。

  15. Squish and CuAAC: Additive-Free Covalent Monolayers of Discrete Molecules in Seconds

    Science.gov (United States)

    Pellow, Matthew A.

    2013-01-01

    A terminal alkyne is immobilized rapidly into a full monolayer by squishing a small volume of a solution of the alkyne between an azide-modified surface and a copper plate. The monolayer is covalently attached to the surface through a copper-catalyzed alkyne-azide cycloaddition (CuAAC) reaction, and the coverages of the immobilized electroactive alkyne species are quantified by cyclic voltammetry. A reaction time of less than twenty seconds is possible with no other reagents required. The procedure is effective in aerobic conditions using either an aqueous or aprotic organic solution of the alkyne (1–100 mM). PMID:23551032

  16. Drug induced `softening' in phospholipid monolayers

    Science.gov (United States)

    Basak, Uttam Kumar; Datta, Alokmay; Bhattacharya, Dhananjay

    2015-06-01

    Compressibility measurements on Langmuir monolayers of the phospholipid Dimystoryl Phospatidylcholine (DMPC) in pristine form and in the presence of the Non-steroidal Anti-inflammatory Drug (NSAID) Piroxicam at 0.025 drug/lipid (D/L) molecular ratio at different temperatures, show that the monolayer exhibits large increase (and subsequent decrease) in compressibility due to the drug in the vicinity of the Liquid Expanded - Liquid Condensed (LE-LC) phase transition. Molecular dynamics simulations of the lipid monolayer in presence of drug molecules show a disordering of the tail tilt, which is consistent with the above result.

  17. Electrochemical Deposition Of Thiolate Monolayers On Metals

    Science.gov (United States)

    Porter, Marc D.; Weissharr, Duane E.

    1995-01-01

    Electrochemical method devised for coating metal (usually, gold) surfaces with adherent thiolate monolayers. Affords greater control over location and amount of material deposited and makes it easier to control chemical composition of deposits. One important potential use for this method lies in fabrication of chemically selective thin-film resonators for microwave oscillators used to detect pollutants: monolayer formulated to bind selectively pollutant chemical species of interest, causing increase in mass of monolayer and corresponding decrease in frequency of resonance. Another important potential use lies in selective chemical derivatization for purposes of improving adhesion, lubrication, protection against corrosion, electrocatalysis, and electroanalysis.

  18. Effects of irradiated biodegradable polymer in endothelial cell monolayer formation

    Energy Technology Data Exchange (ETDEWEB)

    Arbeitman, Claudia R.; Grosso, Mariela F. del [CONICET – Consejo Nacional de Investigaciones Científicas y Técnicas (Argentina); Gerencia de Investigación y Aplicaciones, TANDAR-CNEA (Argentina); Behar, Moni [Instituto de Física, UFRGS, Porto Alegre, RS (Brazil); García Bermúdez, Gerardo, E-mail: ggb@tandar.cnea.gov.ar [CONICET – Consejo Nacional de Investigaciones Científicas y Técnicas (Argentina); Gerencia de Investigación y Aplicaciones, TANDAR-CNEA (Argentina); Escuela de Ciencia y Tecnología, UNSAM (Argentina)

    2013-11-01

    In this work we study cell adhesion, proliferation and cell morphology of endothelial cell cultured on poly-L-lactide acid (PLLA) modified by heavy ion irradiation. Thin films of PLLA samples were irradiated with sulfur (S) at energies of 75 MeV and gold (Au) at 18 MeV ion-beams. Ion beams were provided by the Tandar (Buenos Aires, Argentina) and Tandetron (Porto Alegre, Brazil) accelerators, respectively. The growth of a monolayer of bovine aortic endothelial cells (BAEC) onto unirradiated and irradiated surfaces has been studied by in vitro techniques in static culture. Cell viability and proliferation increased on modified substrates. But the results on unirradiated samples, indicate cell death (necrosis/apoptosis) with the consequent decrease in proliferation. We analyzed the correlation between irradiation parameters and cell metabolism and morphology.

  19. Regulated growth of diatom cells on self-assembled monolayers

    Directory of Open Access Journals (Sweden)

    Kobayashi Koichi

    2007-03-01

    Full Text Available Abstract We succeeded in regulating the growth of diatom cells on chemically modified glass surfaces. Glass surfaces were functionalized with -CF3, -CH3, -COOH, and -NH2 groups using the technique of self-assembled monolayers (SAM, and diatom cells were subsequently cultured on these surfaces. When the samples were rinsed after the adhesion of the diatom cells on the modified surfaces, the diatoms formed two dimensional arrays; this was not possible without the rinsing treatment. Furthermore, we examined the number of cells that grew and their motility by time-lapse imaging in order to clarify the interaction between the cells and SAMs. We hope that our results will be a basis for developing biodevices using living photosynthetic diatom cells.

  20. Oriented crystalline monolayers and bilayers of 2 x 2 silver(1) grid architectures at the air-solution interface: Their assembly and crystal structure elucidation

    DEFF Research Database (Denmark)

    Weissbuch, J.; Baxter, P.N.W.; Kuzmenko, I.;

    2000-01-01

    Oriented crystalline monolayers, similar to 14 Angstrom thick, of a 2 x 2 Ag+ grid complex, self-assembled at the air-solution interface starting from an water-insoluble ligand 3,6-bis[2-(6-phenylpyridine)]pyridazine spread on silver-ion-containing solutions,were examined by grazing-incidence X-r...

  1. Structural and electronic properties of ultrathin picene films on the Ag(100) surface

    Science.gov (United States)

    Kelly, Simon J.; Sorescu, Dan C.; Wang, Jun; Archer, Kaye A.; Jordan, Kenneth D.; Maksymovych, Petro

    2016-10-01

    Using scanning tunneling microscopy and electronic structure calculations, we investigated the assembly and electronic properties of picene molecules on the Ag(100), Ag(111), and Cu(111) surfaces, with particular emphasis on Ag(100). In each case, picene molecules are found to lie parallel to the surface at coverages up to half a monolayer and to adopt alternating parallel and tilted orientations at full monolayer coverage. In the latter case, the arrangement of the molecules is roughly similar to that in the bulk crystal. On the metal surfaces considered, the growth mode of picene is quite different from that of its structural isomer pentacene, which forms a bilayer overlayer on top of a dense monolayer of flat-lying molecules on metal surfaces. Tunneling spectroscopy measurements provide estimates of the energies of several low-lying unfilled molecular orbitals as well as of the highest occupied molecular orbital of the absorbed picene molecules. From analysis of these results, we establish that the on-site Coulomb repulsion for picene decreases by ~ 2 eV in going from the gas phase to the full monolayer on Ag(100), bringing it close to that of the undoped bulk crystal.

  2. Effect of Structure on the Interactions between Five Natural Antimicrobial Compounds and Phospholipids of Bacterial Cell Membrane on Model Monolayers

    Directory of Open Access Journals (Sweden)

    Stella W. Nowotarska

    2014-06-01

    Full Text Available Monolayers composed of bacterial phospholipids were used as model membranes to study interactions of the naturally occurring phenolic compounds 2,5-dihydroxybenzaldehyde and 2-hydroxy-5-methoxybenzaldehyde, and the plant essential oil compounds carvacrol, cinnamaldehyde, and geraniol, previously found to be active against both Gram-positive and Gram-negative pathogenic microorganisms. The lipid monolayers consist of 1,2-dihexadecanoyl-sn-glycero-3-phosphoethanolamine (DPPE, 1,2-dihexa- decanoyl-sn-glycero-3-phospho-(1'-rac-glycerol (DPPG, and 1,1',2,2'-tetratetradecanoyl cardiolipin (cardiolipin. Surface pressure–area (π-A and surface potential–area (Δψ-A isotherms were measured to monitor changes in the thermodynamic and physical properties of the lipid monolayers. Results of the study indicated that the five compounds modified the three lipid monolayer structures by integrating into the monolayer, forming aggregates of antimicrobial –lipid complexes, reducing the packing effectiveness of the lipids, increasing the membrane fluidity, and altering the total dipole moment in the monolayer membrane model. The interactions of the five antimicrobial compounds with bacterial phospholipids depended on both the structure of the antimicrobials and the composition of the monolayers. The observed experimental results provide insight into the mechanism of the molecular interactions between naturally-occurring antimicrobial compounds and phospholipids of the bacterial cell membrane that govern activities.

  3. Study of Thermally Stable Properties and Tribological Behavior of DDP Surface-modified Ag2S Nanoparticles%表面修饰Ag2S纳米微粒的热稳定性能及摩擦学行为研究

    Institute of Scientific and Technical Information of China (English)

    陶小军; 吴志申; 周静芳; 张治军; 党鸿辛

    2002-01-01

    采用有机化合物表面修饰法在溶液中原位合成了DDP(二烷氧基二硫代磷酸吡啶盐) 修饰的Ag2S纳米微粒,该纳米核的粒径小,具有与块体Ag2S相同的晶体结构,表面修饰层的存在能够有效抑制Ag2S纳米核的氧化且使其在有机介质和液体石蜡油中具有良好的分散性.采用多种手段分析表征了DDP修饰Ag2S纳米微粒的结构、热稳定性能和摩擦学性能 .结果表明,经表面修饰的Ag2S纳米微粒具有较好的减摩抗磨性能,可显著提高基础油的失效负荷,是一种新型的润滑油抗磨添加剂.

  4. Method to synthesize metal chalcogenide monolayer nanomaterials

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez-Sanchez, Bernadette A.; Boyle, Timothy J.

    2016-12-13

    Metal chalcogenide monolayer nanomaterials can be synthesized from metal alkoxide precursors by solution precipitation or solvothermal processing. The synthesis routes are more scalable, less complex and easier to implement than other synthesis routes.

  5. Understanding the role of thiol and disulfide self-assembled DNA receptor monolayers for biosensing applications.

    Science.gov (United States)

    Carrascosa, Laura G; Martínez, Lidia; Huttel, Yves; Román, Elisa; Lechuga, Laura M

    2010-09-01

    A detailed study of the immobilization of three differently sulfur-modified DNA receptors for biosensing applications is presented. The three receptors are DNA-(CH)n-SH-, DNA-(CH)n-SS-(CH)n-DNA, and DNA-(CH)n-SS-DMTO. Nanomechanical and surface plasmon resonance biosensors and fluorescence and radiolabelling techniques were used for the experimental evaluation. The results highlight the critical role of sulfur linker type in DNA self-assembly, affecting the kinetic adsorption and spatial distribution of DNA chains within the monolayer and the extent of chemisorption and physisorption. A spacer (mercaptohexanol, MCH) is used to evaluate the relative efficiencies of chemisorption of the three receptors by analysing the extent to which MCH can remove physisorbed molecules from each type of monolayer. It is demonstrated that -SH derivatization is the most suitable for biosensing purposes as it results in densely packed monolayers with the lowest ratio of physisorbed probes.

  6. Microwave-assisted formation of organic monolayers from 1-alkenes on silicon carbide.

    Science.gov (United States)

    van den Berg, Sebastiaan A; Alonso, Jose Maria; Wadhwa, Kuldeep; Franssen, Maurice C R; Wennekes, Tom; Zuilhof, Han

    2014-09-09

    The rate of formation of covalently linked organic monolayers on HF-etched silicon carbide (SiC) is greatly increased by microwave irradiation. Upon microwave treatment for 60 min at 100 °C (60 W), 1-alkenes yield densely packed, covalently attached monolayers on flat SiC surfaces, a process that typically takes 16 h at 130 °C under thermal conditions. This approach was extended to SiC microparticles. The monolayers were characterized by X-ray photoelectron spectroscopy and static water contact angle measurements. The microwave-assisted reaction is compatible with terminal functionalities such as alkenes that enable subsequent versatile "click" chemistry reactions, further broadening the range and applicability of chemically modified SiC surfaces.

  7. Functionalizable self-assembled trichlorosilyl-based monolayer for application in biosensor technology

    Science.gov (United States)

    De La Franier, Brian; Jankowski, Alexander; Thompson, Michael

    2017-08-01

    This paper describes the design and synthesis of 3-(3-(trichlorosilyl)propoxy)propanoyl chloride (MEG-Cl), a compound capable of forming functionalizable monolayers on hydroxylated surfaces. The compound was synthesized in high purity, as suggested by nuclear magnetic resonance analysis, and in moderate overall yield. Contact angle measurement and X-ray photoelectron spectroscopy confirm the binding of MEG-Cl to an amorphous glass substrate and the further modification of the monolayer with a nickel (II)-binding ligand for the purpose of binding polyhistidine-tagged proteins. The compound will be useful in biosensing applications due to its ability to be easily modified with any number of nucleophilic functional groups subsequent to substrate monolayer formation.

  8. Photocatalytic reduction of CO2 with Ag modified TiO2 under UV irradiation%Ag修饰TiO2催化剂紫外光催化还原CO2的研究

    Institute of Scientific and Technical Information of China (English)

    何志桥; 韩晶; 宋爽

    2014-01-01

    采用水解煅烧法制备了不同Ag修饰量的TiO2催化剂(Ag-TiO2).利用X射线衍射(XRD)、X射线光电子光谱(XPS)、透射电子显微镜(TEM)、比表面积测试(BET)和紫外-可见漫反射光谱(UV-vis)等技术分别对纯TiO2和Ag-TiO2样品进行了分析表征.探讨了在紫外光照射的CO2/NaOH水溶液中Ag-TiO2光催化还原CO2反应.研究表明:Ag-TiO2的光利用能力和碳转化能力都较纯TiO2的高,当Ag修饰量为1.0%时达到最大值,其产物量的大小顺序依次为H2>CH4>CH3OH>CO>HCHO.

  9. Fracture Characteristics of Monolayer CVD-Graphene

    OpenAIRE

    Hwangbo, Yun; Lee, Choong-Kwang; Kim, Sang-Min; Kim, Jae-Hyun; Kim, Kwang-Seop; Jang, Bongkyun; Lee, Hak-Joo; Lee, Seoung-Ki; Kim, Seong-Su; Ahn, Jong-Hyun; Lee, Seung-Mo

    2014-01-01

    We have observed and analyzed the fracture characteristics of the monolayer CVD-graphene using pressure bulge testing setup. The monolayer CVD-graphene has appeared to undergo environmentally assisted subcritical crack growth in room condition, i.e. stress corrosion cracking arising from the adsorption of water vapor on the graphene and the subsequent chemical reactions. The crack propagation in graphene has appeared to be able to be reasonably tamed by adjusting applied humidity and stress. ...

  10. In situ structural study on underpotential deposition of Ag on Au(111) electrode using surface X-ray scattering technique

    OpenAIRE

    KONDO, Toshihiro; Morita, Jun; Okamura, Masayuki; Saito, Toshiya; Uosaki, Kohei

    2002-01-01

    In situ surface X-ray scattering (SXS) measurements were carried out to study the structure of a Ag layer on a Au(111) electrode formed by underpotential deposition (upd) in sulfuric acid solution. Specular rod profiles showed that a monolayer of Ag was formed at a potential between the second and third upd peaks, and a bilayer of Ag was formed at a potential between the third upd peak and bulk deposition. Non-specular rod profiles demonstrated that electrochemically deposited Ag atoms both i...

  11. Mass spectrometric analysis of monolayer protected nanoparticles

    Science.gov (United States)

    Zhu, Zhengjiang

    Monolayer protected nanoparticles (NPs) include an inorganic core and a monolayer of organic ligands. The wide variety of core materials and the tunable surface monolayers make NPs promising materials for numerous applications. Concerns related to unforeseen human health and environmental impacts of NPs have also been raised. In this thesis, new analytical methods based on mass spectrometry are developed to understand the fate, transport, and biodistributions of NPs in the complex biological systems. A laser desorption/ionization mass spectrometry (LDI-MS) method has been developed to characterize the monolayers on NP surface. LDI-MS allows multiple NPs taken up by cells to be measured and quantified in a multiplexed fashion. The correlations between surface properties of NPs and cellular uptake have also been explored. LDI-MS is further coupled with inductively coupled plasma mass spectrometry (ICP-MS) to quantitatively measure monolayer stability of gold NPs (AuNPs) and quantum dots (QDs), respectively, in live cells. This label-free approach allows correlating monolayer structure and particle size with NP stability in various cellular environments. Finally, uptake, distribution, accumulation, and excretion of NPs in higher order organisms, such as fish and plants, have been investigated to understand the environmental impact of nanomaterials. The results indicate that surface chemistry is a primary determinant. NPs with hydrophilic surfaces are substantially less toxic and present a lower degree of bioaccumulation, making these nanomaterials attractive for sustainable nanotechnology.

  12. Poly(ethylene glycol) monolayer formation and stability on gold and silicon nitride substrates.

    Science.gov (United States)

    Cerruti, Marta; Fissolo, Stefano; Carraro, Carlo; Ricciardi, Carlo; Majumdar, Arun; Maboudian, Roya

    2008-10-07

    Poly(ethylene glycol) (PEG) self-assembled monolayers (SAMs) are extensively used to modify substrates to prevent nonspecific protein adsorption and to increase hydrophilicity. X-ray photoelectron spectroscopy analysis, complemented by water contact angle measurements, is employed to investigate the formation and stability upon aging and heating of PEG monolayers formed on gold and silicon nitride substrates. In particular, thiolated PEG monolayers on gold, with and without the addition of an undecylic spacer chain, and PEG monolayers formed with oxysilane precursors on silicon nitride have been probed. It is found that PEG-thiol SAMs are degraded after less than two weeks of exposure to air and when heated at temperatures as low as 120 degrees C. On the contrary, PEG-silane SAMs are stable for more than two weeks, and fewer molecules are desorbed even after two months of aging, compared to those desorbed in two weeks from the PEG-thiol SAMs. A strongly bound hydration layer is found on PEG-silane SAMs aged for two months. Heating PEG-silane SAMs to temperatures as high as 160 degrees C improves the quality of the monolayer, desorbing weakly bound contaminants. The differences in stability between PEG-thiol SAMs and PEG-silane SAMs are ascribed to the different types of bonding to the surface and to the fact that the thiol-Au bond can be easily oxidized, thus causing desorption of PEG molecules from the surface.

  13. Tunnelling characteristics of Stone-Wales defects in monolayers of Sn and group-V elements

    Science.gov (United States)

    Jamdagni, Pooja; Kumar, Ashok; Thakur, Anil; Pandey, Ravindra; Ahluwalia, P. K.

    2017-10-01

    Topological defects in ultrathin layers are often formed during synthesis and processing, thereby strongly influencing the electronic properties of layered systems. For the monolayers of Sn and group-V elements, we report the results based on density functional theory determining the role of Stone-Wales (SW) defects in modifying their electronic properties. The calculated results find the electronic properties of the Sn monolayer to be strongly dependent on the concentration of SW defects, e.g. defective stanene has nearly zero band gap (≈0.03 eV) for the defect concentration of 2.2  ×  1013 cm-2 which opens up to 0.2 eV for the defect concentration of 3.7  ×  1013 cm-2. In contrast, SW defects appear to induce conduction states in the semiconducting monolayers of group-V elements. These conduction states act as channels for electron tunnelling, and the calculated tunnelling characteristics show the highest differential conductance for the negative bias with the asymmetric current-voltage characteristics. On the other hand, the highest differential conductance was found for the positive bias in stanene. Simulated STM topographical images of stanene and group-V monolayers show distinctly different features in terms of their cross-sectional views and distance-height profiles. These distinctive features can serve as fingerprints to identify the topological defects in experiments for the monolayers of group-IV and group-V elements.

  14. Synthesis and properties of polyamide–Ag2S composite based solar energy absorber surfaces

    NARCIS (Netherlands)

    Krylovaa, Valentina; Baltrusaitis, Jonas

    2013-01-01

    Silver sulfide (Ag2S), an efficient solar light absorber, was synthesized using a modified chemical bath deposition (CBD) method and polyamide 6 (PA) as a host material via solution phase reaction between AgNO3 and Na2S2O3. X-ray diffraction (XRD) data showed a single, α-Ag2S (acanthite), crystallin

  15. The preparation and antibacterial effects of dopa-cotton/AgNPs

    Energy Technology Data Exchange (ETDEWEB)

    Xu Hong, E-mail: hxu@dhu.edu.cn [Key Lab of Science and Technology of Eco-textile, Ministry of Education, College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China); Shi Xue; Ma Hui; Lv Yihang; Zhang Linping [Key Lab of Science and Technology of Eco-textile, Ministry of Education, College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China); Mao Zhiping, E-mail: zhpmao@dhu.edu.cn [Key Lab of Science and Technology of Eco-textile, Ministry of Education, College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China)

    2011-05-15

    Silver nanoparticles (AgNPs) have been known to have powerful antibacterial activity. In this paper, in situ generation of AgNPs on the surface of dopamine modified cotton fabrics (dopa-cotton/AgNPs) in aqueous solution under room temperature is presented. X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscope (FE-SEM) were used to analyze the surface chemical composition and the morphology of the modified cotton fabrics, respectively. The results indicated that the surface of cotton fabrics was successfully coated with polydopamine and AgNPs. The cotton fabrics with AgNPs showed durable antibacterial activity.

  16. AGS experiments - 1994, 1995, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Depken, J.C.

    1997-01-01

    This report contains the following information on the Brookhaven AGS Accelerator complex: FY 1996 AGS schedule as run; FY 1997 AGS schedule (working copy); AGS beams 1997; AGS experimental area FY 1994 physics program; AGS experimental area FY 1995 physics program; AGS experimental area FY 1996 physics program; AGS experimental area FY 1997 physics program (in progress); a listing of experiments by number; two-phage summaries of each experiment begin here, also ordered by number; listing of publications of AGS experiments begins here; and listing of AGS experimenters begins here.

  17. Lateral interactions at functional monolayers

    NARCIS (Netherlands)

    Hsu, Shu Han

    2010-01-01

    Molecular nanostructures are important in the emerging field of nanoscience, because of the tunability of the properties of these structures. Nanostructures based on molecular interactions can be manipulated by selectively modifying specific functional groups while leaving the rest of the structures

  18. Assembly of organic monolayers on polydicyclopentadiene.

    Science.gov (United States)

    Perring, Mathew; Bowden, Ned B

    2008-09-16

    The first well-defined organic monolayers assembled on polydicyclopentadiene is reported. Commercial grade dicyclopentadiene was polymerized with the Grubbs' second-generation catalyst in a fume hood under ambient conditions at very low monomer to catalyst loadings of 20 000 to 1. This simple method resulted in a polymer that was a hard solid and appeared slightly yellow. Brief exposures of a few seconds of this polymer to Br 2 lead to a surface with approximately half of the olefins brominated as shown by X-ray photoelectron spectroscopy (XPS) and attenuated total reflection-infrared (ATR-IR) spectroscopy. The ATR-IR spectroscopy was carried out with the polymer in contact with a Ge hemisphere housed in a GATR accessory from Harrick. This brominated polydicyclopentadiene was immersed in DMF with 4-(trifluoromethyl)benzylamine to assemble a monolayer. The amines displaced Br on the surface to form a monolayer that exposed a CF 3 group on the surface. The surface was extensively studied by XPS using the method described by Tougaard to find the distribution of F within the surface layer. The ratio for the peak area, Ap, to the background height, B, measured 30 eV below the peak maximum was 109.8 eV. This value clearly indicated that F was found only at the surface and was not found within the polymer. A surface coverage of 1.37 amines per nm (2) was estimated and indicated that the monolayer was 28% as dense as a similar monolayer assembled from thiols on gold. Finally, a simple method to pattern these monolayers using soft lithography is described. This work is critically important because it reports the first monolayers on a relatively new and emerging polymer that has many desirable physical characteristics such as high hardness, chemical stability, and ease of forming different shapes.

  19. Multiplexed DNA-Modified Electrodes

    OpenAIRE

    Slinker, Jason D.; Muren, Natalie B.; Gorodetsky, Alon A.; Barton, Jacqueline K.

    2010-01-01

    We report the use of silicon chips with 16 DNA-modified electrodes (DME chips) utilizing DNA-mediated charge transport for multiplexed detection of DNA and DNA-binding protein targets. Four DNA sequences were simultaneously distinguished on a single DME chip with fourfold redundancy, including one incorporating a single base mismatch. These chips also enabled investigation of the sequence-specific activity of the restriction enzyme Alu1. DME chips supported dense DNA monolayer formation with ...

  20. Corrosion protection ability of self-assembled monolayer of 3-amino-5-mercapto-1,2,4-triazole on copper electrode

    Energy Technology Data Exchange (ETDEWEB)

    Rajkumar, Ganesan; Sethuraman, Mathur Gopalakrishnan, E-mail: mgsethu@rediffmail.com

    2014-07-01

    The self-assembled monolayer (SAM) of 3-amino-5-mercapto-1,2,4-triazole (AMTa) was formed on a copper surface and characterized using cyclic voltammetry, Fourier Transform Infra-red spectroscopy and scanning electron microscopy. Quantum chemical calculations suggested the stronger interaction between AMTa and copper. The protection ability of SAM has been evaluated using electrochemical impedance spectroscopy and potentiodynamic polarization measurements. The formed monolayer showed significant protection ability in 1% NaCl medium. The enhanced corrosion protection ability could be due to the compact film structure which blocks the electron transfer from the solution to AMTa monolayer modified copper substrate. - Highlights: • Self-assembled monolayer (SAM) of AMTa has been achieved on copper surface. • Monolayer formed has been duly characterized. • SAM of AMTa has been shown to offer significant protection to copper in NaCl medium.

  1. Quantifying the origin of released Ag+ ions from nanosilver.

    Science.gov (United States)

    Sotiriou, Georgios A; Meyer, Andreas; Knijnenburg, Jesper T N; Panke, Sven; Pratsinis, Sotiris E

    2012-11-13

    Nanosilver is most attractive for its bactericidal properties in modern textiles, food packaging, and biomedical applications. Concerns, however, about released Ag(+) ions during dispersion of nanosilver in liquids have limited its broad use. Here, nanosilver supported on nanostructured silica is made with closely controlled Ag size both by dry (flame aerosol) and by wet chemistry (impregnation) processes without any surface functionalization that could interfere with its ion release. It is characterized by electron microscopy, atomic absorption spectroscopy, and X-ray diffraction, and its Ag(+) ion release in deionized water is monitored electrochemically. The dispersion method of nanosilver in solutions affects its dissolution rate but not the final Ag(+) ion concentration. By systematically comparing nanosilver size distributions to their equilibrium Ag(+) ion concentrations, it is revealed that the latter correspond precisely to dissolution of one to two surface silver oxide monolayers, depending on particle diameter. When, however, the nanosilver is selectively conditioned by either washing or H(2) reduction, the oxide layers are removed, drastically minimizing Ag(+) ion leaching and its antibacterial activity against E. coli . That way the bactericidal activity of nanosilver is confined to contact with its surface rather than to rampant ions. This leads to silver nanoparticles with antibacterial properties that are essential for medical tools and hospital applications.

  2. Synthesis,characterization and photocatalysis of Ag modified nano-ZnO%Ag修饰的纳米ZnO的合成、表征及光催化特性

    Institute of Scientific and Technical Information of China (English)

    周小岩; 王文新; 张晶

    2010-01-01

    采用水热合成和光合成法制备了ZnO纳米粉体及不同Ag修饰量的纳米ZnO (Ag/ZnO),并用X射线衍射(XRD)、扫描电子显微镜(SEM)分析了它们的物相结构和晶粒形貌.以亚甲基蓝为污染物模型,在紫外光照射下考察了ZnO纳米粉体及不同Ag修饰量的纳米Ag/ZnO的光催化活性.结果表明,Ag能成功地负载到ZnO表面,且Ag/ZnO 的光催化性能与Ag的负载量有关.当Ag修饰量为1.0%时,光催化能力高于ZnO纳米粉体;Ag修饰量为5.0%时,光催化能力最高;Ag修饰量为8.0%时,光催化能力反而降低.

  3. Cyclic Voltammetric Determination of Norepinephrine with Ag-Tryptophan Compound Film Modified Glassy Carbon Electrode%用银-色氨酸复合膜修饰玻碳电极循环伏安法测定去甲肾上腺素

    Institute of Scientific and Technical Information of China (English)

    马心英; 李霞; 石春杰

    2012-01-01

    The modified electrode (Ag-Try/GCE) was prepared by electrodeposition of a film of silver and poly-tryptophan on the surface of glassy carbon electrode at the potential range from 0. 8 V to 1.8 V (vs. Ag/ AgC1) from a solution containing 1.0 mol·L^-1 AgNO; and 5. 58 × 10 ^-2mol·L^-1 tryptophan. The surface property of the modified electrode was characterized by scanning electron microscopy, and its electrochemical property studied by cyclic voltammetry. It was found that a pair of significant oxidation and reduction peaks of NE was observed at the Ag Try/GCE with the Epc at 0. 306 V and Epa at 0. 368 V in PBS of pH 6.0. Based on these findings, a selective method for determination of NE by cyclic voltammetry was proposed. Under the optimized experimental conditions, linear relationship between values of oxidation peak current and concentration of NE was obtained in 2 segmental ranges of 3.4× 10 ^-7-8. 3 × 10 6 mol·L^-1 and 8. 3 × 10 ^-6 -1.1 × 10^- 4mol·L^-1 , with detection limit (3S/N) of 4. 3 ×10 ^-8 mol·L^-1. The proposed method was used in the determination of NE in medicine, giving values of recovery found by standard addition method in the range of 95.6%- 99.40%%在含有1.0mol·L^-1叫硝酸银、5.58×10^-2mol·L^-1叫色氨酸的溶液中,于-0.8-1.8V(vs.Ag/AgCI)电位下,在玻碳电极表面电沉积一层银一色氨酸复合膜,制得银一色氨酸复合膜修饰玻碳电极(Ag-TRY/GCE)。采用扫描电镜对电极表面的性能进行表征,循环伏安法对其电化学性能进行研究。试验发现:在pH6.0磷酸盐缓冲溶液中,去甲肾上腺素(NE)在修饰电极出现一对明显的氧化还原峰,氧化峰电位为0.306V,还原峰电位为0.368V,提出了用循环伏安法测定NE的方法。在试验条件下,氧化峰电流与去甲肾上腺素浓度在3.4×10^-7~8.3×1^-61.0mol·L^-1叫和8.3×10^-6~1.1×10^-4mol·L^-1。叫两段范围内

  4. Phosphonate-anchored monolayers for antibody binding to magnetic nanoparticles.

    Science.gov (United States)

    Benbenishty-Shamir, Helly; Gilert, Roni; Gotman, Irena; Gutmanas, Elazar Y; Sukenik, Chaim N

    2011-10-04

    Targeted delivery of magnetic iron oxide nanoparticles (IONPs) to a specific tissue can be achieved by conjugation with particular biological ligands on an appropriately functionalized IONP surface. To take best advantage of the unique magnetic properties of IONPs and to maximize their blood half-life, thin, strongly bonded, functionalized coatings are required. The work reported herein demonstrates the successful application of phosphonate-anchored self-assembled monolayers (SAMs) as ultrathin coatings for such particles. It also describes a new chemical approach to the anchoring of antibodies on the surface of SAM-coated IONPs (using nucleophilic aromatic substitution). This anchoring strategy results in stable, nonhydrolyzable, covalent attachment and allows the reactivity of the particles toward antibody binding to be activated in situ, such that prior to the activation the modified surface is stable for long-term storage. While the SAMs do not have the well-packed crystallinity of other such monolayers, their structure was studied using smooth model substrates based on an iron oxide layer on a double-side polished silicon wafer. In this way, atomic force microscopy, ellipsometry, and contact angle goniometry (tools that could not be applied to the nanoparticles' surfaces) could contribute to the determination of their monomolecular thickness and uniformity. Finally, the successful conjugation of IgG antibodies to the SAM-coated IONPs such that the antibodies retain their biological activity is verified by their complexation to a secondary fluorescent antibody.

  5. Evidence for superconductivity in Li-decorated monolayer graphene.

    Science.gov (United States)

    Ludbrook, B M; Levy, G; Nigge, P; Zonno, M; Schneider, M; Dvorak, D J; Veenstra, C N; Zhdanovich, S; Wong, D; Dosanjh, P; Straßer, C; Stöhr, A; Forti, S; Ast, C R; Starke, U; Damascelli, A

    2015-09-22

    Monolayer graphene exhibits many spectacular electronic properties, with superconductivity being arguably the most notable exception. It was theoretically proposed that superconductivity might be induced by enhancing the electron-phonon coupling through the decoration of graphene with an alkali adatom superlattice [Profeta G, Calandra M, Mauri F (2012) Nat Phys 8(2):131-134]. Although experiments have shown an adatom-induced enhancement of the electron-phonon coupling, superconductivity has never been observed. Using angle-resolved photoemission spectroscopy (ARPES), we show that lithium deposited on graphene at low temperature strongly modifies the phonon density of states, leading to an enhancement of the electron-phonon coupling of up to λ ≃ 0.58. On part of the graphene-derived π*-band Fermi surface, we then observe the opening of a Δ ≃ 0.9-meV temperature-dependent pairing gap. This result suggests for the first time, to our knowledge, that Li-decorated monolayer graphene is indeed superconducting, with Tc ≃ 5.9 K.

  6. 高活性Ag修饰TiO2空心八面体光催化剂的简易模板诱导合成%Facile template-induced synthesis of Ag-modified TiO2 hollow octahedra with high photocatalytic activity

    Institute of Scientific and Technical Information of China (English)

    王雪飞; 余锐; 王康; 杨桂全; 余火根

    2015-01-01

    Noble metal/titania hollow nanomaterials usually exhibit excellent photocatalytic activity because of their high specific surface area, low density, good surface permeability, strong light‐harvesting capacity, and rapid interfacial charge transfer. However, the present preparation methods usually include complicated and multistep procedures, which can cause damage to the hollow nanostruc‐tures. In this paper, a facile template‐induced synthesis, based on a template‐directed deposition and in situ template‐sacrificial dissolution, was employed to prepare Ag‐modified TiO2 (Ag/TiO2) hollow octahedra using Ag2O octahedra as templates and TiF4 as the precursor. In the synthetic strategy, the shells of TiO2 hollow octahedra were formed by coating TiO2 nanoparticles on the sur‐face of Ag2O templates based on the template‐directed deposition. Simultaneously, the Ag2O tem‐plates can be in situ removed by dissolving the Ag2O octahedral template in HF solution produced via the hydrolysis reaction of TiF4 in the reaction system. In addition, Ag nanoparticles were depos‐ited on the inside and outside surfaces of TiO2 shells by effectively using the photosensitive proper‐ties of Ag2O and Ag+ions under light irradiation, along with the formation of TiO2 hollow octahedra. The Ag/TiO2 hollow octahedra exhibited high photocatalytic activity because of their (1) short dif‐fusion distances between photogenerated electrons and holes because of the thin shells of Ag/TiO2 hollow octahedral, (2) deposition of Ag nanoparticles on the inside and outside surfaces of TiO2 shells, and (3) rapid interfacial charge transfer between TiO2 shells and Ag nanoparticles. This work may also provide new insights into preparing other Ag‐modified and hollow nanostructured photo‐catalysts.%贵金属修饰的TiO2空心纳米光催化材料由于具有大的比表面积、低的质量密度、良好的表面渗透性、强的光吸收能力以及界面电荷的快速转移,因而

  7. Preparation and Effects on Photocatalytic Degradation of Ag-Doped TiO_2 Powders Modified with APS%Ag掺杂APS改性的TiO_2颗粒的制备及其光催化降解作用

    Institute of Scientific and Technical Information of China (English)

    李贵安; 焦飞; 邓仲勋; 张亚娟; 牛文成; 郑海荣

    2011-01-01

    为提高Ag/TiO2纳米颗粒的光催化降解作用,采用聚合凝胶工艺路线,以钛酸四丁酯为前驱体,硝酸银为银源,通过向反应体系引入鳌合剂醋酸、表面改性剂γ-氨丙基三乙氧基硅烷(APS)以及还原剂甲醛等添加剂,制备出TiO2粉体及Ag/TiO2纳米复合粉体。利用FT-IR、XRD、TG-DTA、TEM和UV-Vis-NIR等手段对样品进行表征。结果表明,经γ-氨丙基三乙氧基硅烷改性的TiO2颗粒掺Ag后分散性得到改善,粒径约1 nm的Ag颗粒较均匀地分布在10~15 nm TiO2颗粒上;可见光的利用和锐钛矿热稳定性都得到提高;Ag/TiO2纳米颗粒在光照下对甲基橙具有良好的光催化降解效果。%To improve the effects of Ag/TiO2 on photocatalytic degradation,using Ti(OC4H9)4 as raw material and silver nitrate as silver source,nano-TiO2 and nano-sized Ag/TiO2 particles were prepared via polymer gel process by adding acetic acid as chelating agent,3-aminopropyltriethoxysilane as surface modification agent and formaldehyde as reducing agent to the reaction system.The nano-powders of TiO2 and Ag/TiO2 were characterized by Fourier transform infrared(FT-IR) spectroscopy,X-ray diffractometry(XRD),thermogravimetry-differential thermal analysis(TG-DTA),transmission electron microscopy(TEM) and ultraviolet-visible-near infrared(UV-Vis-NIR) absorption.The results indicate that the composite powders of the surface modified Ag-doped TiO2 with 3-aminopropyltriethoxysilane improve the dispersion of the TiO2 particles,and silver particles,with average grain diameter of 1 nm,are distributed on surfaces of TiO2 particles of 10~15 nm;Absorption of visible light and heat stability of anatase are improved.Ag/TiO2 shows a good effect on the photocatalytic degradation of methyl orange solution under xenon lamp irradiation.

  8. Synthesis, Characterization and Photocatalytic Performance of Ag-modified TiO2 Catalysts for the Degradation of Gas-phase Toluene%Ag改性TiO2催化剂的制备、表征及其甲苯气相光催化降解性能

    Institute of Scientific and Technical Information of China (English)

    方奕文; 余林; 叶飞; 孙明

    2011-01-01

    Ag-modified TiO2 catalysts were synthesized by sol-gel method and characterized by XRD, SEM, BET, O2-TPD and UV-Vis DRS. The results showed that the Ag-TiO2 catalysts demonstrated smaller particle sizes, larger specific surface areas and higher absorbing ability in visible light when compared with TiO2 catalyst. The surface adsorbed oxygen and Ag electron trapping center also appeared on the Ag-TiO2 catalysts. The single-pass degradation rate of toluene reached 42.9% when the Ag/Ti atomic ratio was 1.6%. The catalysts were transfered from pure anatase phase to anatase-rutile composite phase when the calcination temperatures were increased. The coexisting of anatase phase and rutile phase with appropriate ratio can reduce the recombination probability of the electron-hole pairs and enhance the toluene degradation activities.%用溶胶-凝胶法制备Ag改性的TiO2催化剂,并用XRD、SEM、BET、O2-TPD和UV-Vis DRS等测试手段对其进行表征.结果表明,与TiO2相比,所制备催化剂颗粒直径明显减小,比表面积明显增大,对可见光的吸收明显增强,同时出现了表面吸附氧和Ag电子捕获中心.甲苯气相光催化降解结果显示,当Ag与Ti的摩尔比(nAg/nTi)为1.6%时,甲苯单程降解率达到42.9%.焙烧温度提高,使催化剂从单一锐钛矿相向锐钛矿、金红石混合相转变,适量比例的锐钛矿相和金红石相共存,能减少电子-空穴对复合几率,提高催化剂的甲苯降解活性.

  9. Thermal ripples in model molybdenum disulfide monolayers

    Energy Technology Data Exchange (ETDEWEB)

    Remsing, Richard C.; Klein, Michael L. [Institute for Computational Molecular Science, Center for the Computational, Design of Functional Layered Materials, and Department of Chemistry, Temple University, 1925 N. 12th St., 19122, Philadelphia, PA (United States); Waghmare, Umesh V. [Theoretical Sciences Unit, Jawaharlal Nehru Centre for Advanced Scientific Research, 560 064, Jakkur, Bangalore (India)

    2017-01-15

    Molybdenum disulfide (MoS{sub 2}) monolayers have the potential to revolutionize nanotechnology. To reach this potential, it will be necessary to understand the behavior of this two-dimensional (2D) material on large length scales and under thermal conditions. Herein, we use molecular dynamics (MD) simulations to investigate the nature of the rippling induced by thermal fluctuations in monolayers of the 2H and 1T phases of MoS{sub 2}. The 1T phase is found to be more rigid than the 2H phase. Both monolayer phases are predicted to follow long wavelength scaling behavior typical of systems with anharmonic coupling between vibrational modes as predicted by classic theories of membrane-like systems. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  10. Thermal transport in monolayer InSe

    Science.gov (United States)

    Nissimagoudar, Arun S.; Ma, Jinlong; Chen, Yani; Li, Wu

    2017-08-01

    Two-dimensional InSe, a recently synthesized semiconductor having a moderate band gap, has gained attention due to its ultra high mobility and high photo-responsivity. In this work, we calculate the lattice thermal conductivity (κ) of monolayer InSe by solving the phonon Boltzmann transport equation (BTE) with first-principles calculated inter atomic force constants. κ of monolayer InSe is isotropic and found to be around 27.6 W m K-1 at room temperature along the in-plane direction. The size dependence of κ shows the size effect can persist up to 20 μm. Further, κ can be reduced to half by tuning the sample size to 300 nm. This low value suggests that κ might be a limiting factor for emerging nanoelectronic applications of monolayer InSe.

  11. Elastic bending modulus of monolayer graphene

    Energy Technology Data Exchange (ETDEWEB)

    Lu Qiang; Huang Rui [Department of Aerospace Engineering and Engineering Mechanics, University of Texas, Austin, TX 78712 (United States); Arroyo, Marino [Department of Applied Mathematics 3, LaCaN, Universitat Politecnica de Catalunya (UPC), Barcelona 08034 (Spain)

    2009-05-21

    An analytic formula is derived for the elastic bending modulus of monolayer graphene based on an empirical potential for solid-state carbon atoms. Two physical origins are identified for the non-vanishing bending stiffness of the atomically thin graphene sheet, one due to the bond-angle effect and the other resulting from the bond-order term associated with the dihedral angles. The analytical prediction compares closely with ab initio energy calculations. Pure bending of graphene monolayers into cylindrical tubes is simulated by a molecular mechanics approach, showing slight nonlinearity and anisotropy in the tangent bending modulus as the bending curvature increases. An intrinsic coupling between bending and in-plane strain is noted for graphene monolayers rolled into carbon nanotubes. (fast track communication)

  12. Fullerene monolayer formation by spray coating.

    Science.gov (United States)

    Cervenka, J; Flipse, C F J

    2010-02-10

    Many large molecular complexes are limited in thin film applications by their insufficient thermal stability, which excludes deposition via commonly used vapour phase deposition methods. Here we demonstrate an alternative way of monolayer formation of large molecules by a simple spray coating method under ambient conditions. This technique has been successfully applied on C(60) dissolved in toluene and carbon disulfide. Monolayer thick C(60) films have been formed on graphite and gold surfaces at particular deposition parameters, as confirmed by atomic force and scanning tunnelling microscopies. Structural and electronic properties of spray coated C(60) films on Au(111) have been found comparable to thermally evaporated C(60). We attribute the monolayer formation in spray coating to a crystallization process mediated by an ultrathin solution film on a sample surface.

  13. Magneto photoluminescence measurements of tungsten disulphide monolayers

    Science.gov (United States)

    Kuhnert, Jan; Rahimi-Iman, Arash; Heimbrodt, Wolfram

    2017-03-01

    Layered transition-metal dichalcogenides have attracted great interest in the last few years. Thinned down to the monolayer limit they change from an indirect band structure to a direct band gap in the visible region. Due to the monolayer thickness the inversion symmetry of the crystal is broken and spin and valley are coupled to each other. The degeneracy between the two equivalent valleys, K and K‧, respectively, can be lifted by applying an external magnetic field. Here, we present photoluminescence measurements of CVD-grown tungsten disulphide (WS2) monolayers at temperatures of 2 K. By applying magnetic fields up to 7 T in Faraday geometry, a splitting of the photoluminescence peaks can be observed. The magnetic field dependence of the A-exciton, the trion and three bound exciton states is discussed and the corresponding g-factors are determined.

  14. Thermodynamic balance of perylene self-assembly on Ag(110)

    Science.gov (United States)

    Bobrov, Kirill; Kalashnyk, Nataliya; Guillemot, Laurent

    2016-10-01

    We present a room temperature STM study of perylene adsorption on Ag(110) at the monolayer coverage regime. We found that structure and symmetry of the perylene monolayer are settled by thermodynamic balance of the three factors: (i) the ability of perylene molecules to recognize specific adsorption sites on the (110) lattice, (ii) the intermolecular interaction, and (iii) the accommodation of thermal motion of the molecules. The moderate strength of the site recognition and the intermolecular interaction, of the same order of magnitude as kT ˜ 25 meV, represents a key feature of the thermodynamic balance. It bestows to this system the unique quality to form the quasi-liquid monolayer of epitaxial as well as self-assembling character. The perylene monolayer accommodates the short-range motion of the molecules instead of quenching it. It precludes the formation of possible solid nuclei and maintains common registry of the included molecules. The surface registry of the quasi-liquid phase is provided by locking of a structure-related fraction of the perylene molecules into specific adsorption sites of the (110) lattice favorable in terms of intermolecular interaction.

  15. On the Hopping Efficiency of Nanoparticles in the Electron Transfer across Self‐Assembled Monolayers

    DEFF Research Database (Denmark)

    Liu, Feng; Khan, Kamran; Liang, Jing‐Hong

    2013-01-01

    Redox reactions of solvated molecular species at gold‐electrode surfaces modified by electrochemically inactive self‐assembled molecular monolayers (SAMs) are found to be activated by introducing Au nanoparticles (NPs) covalently bound to the SAM to form a reactive Au–alkanedithiol–NP–molecule hy......Redox reactions of solvated molecular species at gold‐electrode surfaces modified by electrochemically inactive self‐assembled molecular monolayers (SAMs) are found to be activated by introducing Au nanoparticles (NPs) covalently bound to the SAM to form a reactive Au......–alkanedithiol–NP–molecule hybrid entity. The NP appears to relay long‐range electron transfer (ET) so that the rate of the redox reaction may be as efficient as directly on a bare Au electrode, even though the ET distance is increased by several nanometers. In this study, we have employed a fast redox reaction of surface...

  16. Stiffness of lipid monolayers with phase coexistence.

    Science.gov (United States)

    Caruso, Benjamín; Mangiarotti, Agustín; Wilke, Natalia

    2013-08-27

    The surface dilational modulus--or compressibility modulus--has been previously studied for monolayers composed of pure materials, where a jump in this modulus was related with the onset of percolation as a result of the establishment of a connected structure at the molecular level. In this work, we focused on monolayers composed of two components of low lateral miscibility. Our aim was to investigate the compressibility of mixed monolayers at pressures and compositions in the two-phase region of the phase diagram, in order to analyze the effect of the mechanical properties of each phase on the stiffness of the composite. In nine different systems with distinct molecular dipoles and charges, the stiffness of each phase and the texture at the plane of the monolayer were studied. In this way, we were able to analyze the general compressibility of two-phase lipid monolayers, regardless of the properties of their constituent parts. The results are discussed in the light of the following two hypotheses: first, the stiffness of the composite could be dominated by the stiffness of each phase as a weighted sum according to the percentage of each phase area, regardless of the distribution of the phases in the plane of the monolayer. Alternatively, the stiffness of the composite could be dominated by the mechanical properties of the continuous phase. Our results were better explained by this latter proposal, as in all the analyzed mixtures it was found that the mechanical properties of the percolating phase were the determining factors. The value of the compression modulus was closer to the value of the connected phase than to that of the dispersed phase, indicating that the bidimensional composites displayed mechanical properties that were related to the properties of each phases in a rather complex manner.

  17. The role of Ag precipitates in Cu-12 wt% Ag

    Energy Technology Data Exchange (ETDEWEB)

    Yao, D.W.; Song, L.N. [Department of Materials Science and Engineering, Zhejiang University, Zheda Road No.38, Hangzhou, Zhejiang 310027 (China); Dong, A.P.; Wang, L.T. [China Railway Construction Electrification Bureau Group Co.,Ltd., Beijing 100036 (China); Zhang, L. [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Meng, L., E-mail: mengliang@zju.edu.cn [Department of Materials Science and Engineering, Zhejiang University, Zheda Road No.38, Hangzhou, Zhejiang 310027 (China)

    2012-12-15

    The Cu-12 wt% Ag was prepared to investigate the role of Ag precipitates on the properties of the alloy. Two kinds of heat treatment procedures were adopted to produce different amount of Ag precipitates in the Cu-12 wt% Ag. The microstructure of Ag precipitates was systematically observed by optical microscopy and electron microscopy. The Cu-12 wt% Ag with more Ag precipitates exhibits higher strength and lower electrical conductivity. More Ag precipitates results in more phase interface and less Ag atoms dissolved in Cu matrix. By comparing the strengthening effect and electron scattering effect of phase interface and dissolved Ag atoms, it is conclude that the interface between Cu matrix and Ag precipitates could significantly block dislocation movement and enhance electron scattering in Cu-Ag alloys.

  18. Low temperature photoresponse of monolayer tungsten disulphide

    Directory of Open Access Journals (Sweden)

    Bingchen Cao

    2014-11-01

    Full Text Available High photoresponse can be achieved in monolayers of transition metal dichalcogenides. However, the response times are inconveniently limited by defects. Here, we report low temperature photoresponse of monolayer tungsten disulphide prepared by exfoliation and chemical vapour deposition (CVD method. The exfoliated device exhibits n-type behaviour; while the CVD device exhibits intrinsic behaviour. In off state, the CVD device has four times larger ratio of photoresponse for laser on/off and photoresponse decay–rise times are 0.1 s (limited by our setup, while the exfoliated device has few seconds. These findings are discussed in terms of charge trapping and localization.

  19. Sub-THz Characterisation of Monolayer Graphene

    Directory of Open Access Journals (Sweden)

    Ehsan Dadrasnia

    2014-01-01

    Full Text Available We explore the optical and electrical characteristics of monolayer graphene by using pulsed optoelectronic terahertz time-domain spectroscopy in the frequency range of 325–500 GHz based on fast direct measurements of phase and amplitude. We also show that these parameters can, however, be measured with higher resolution using a free space continuous wave measurement technique associated with a vector network analyzer that offers a good dynamic range. All the scattering parameters (both magnitude and phase are measured simultaneously. The Nicholson-Ross-Weir method is implemented to extract the monolayer graphene parameters at the aforementioned frequency range.

  20. Nonlinear optical studies of organic monolayers

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Y.R.

    1988-02-01

    Second-order nonlinear optical effects are forbidden in a medium with inversion symmetry, but are necessarily allowed at a surface where the inversion summary is broken. They are often sufficiently strong so that a submonolayer perturbation of the surface can be readily detected. They can therefore be used as effective tools to study monolayers adsorbed at various interfaces. We discuss here a number of recent experiments in which optical second harmonic generation (SHG) and sum-frequency generation (SFG) are employed to probe and characterize organic monolayers. 15 refs., 5 figs.

  1. Incoherent Ag islands growth on Ni(100)

    Science.gov (United States)

    Marie, J. B.; Braems, I.; Bellec, A.; Chacon, C.; Creuze, J.; Girard, Y.; Gueddani, S.; Lagoute, J.; Repain, V.; Rousset, S.

    2017-02-01

    Growth of two-dimensional superstructure and island morphologies of silver atoms evaporated on a nickel (100) surface are studied by scanning tunneling microscopy. Near-equilibrium islands form at moderate annealing temperature (lower than 500 K) and present two kinds of morphologies. While they share a common monolayer c(2×8) superstructure, two distinct populations of islands coexist: rounded islands grown on the surface and spindle-shaped islands grown inside the Ni surface. The latter present a clear saturation of their density with increasing coverage. These shapes are mostly dominated by boundary energies as confirmed by a simple two-dimensional Wulff model whose parameters are derived using molecular statics simulations. Further annealing to 700 K leads to long Ag strips decorating the Ni step edges.

  2. High-Reliability Low-Ag-Content Sn-Ag-Cu Solder Joints for Electronics Applications

    Science.gov (United States)

    Shnawah, Dhafer Abdulameer; Said, Suhana Binti Mohd; Sabri, Mohd Faizul Mohd; Badruddin, Irfan Anjum; Che, Fa Xing

    2012-09-01

    Sn-Ag-Cu (SAC) alloy is currently recognized as the standard lead-free solder alloy for packaging of interconnects in the electronics industry, and high- Ag-content SAC alloys are the most popular choice. However, this choice has been encumbered by the fragility of the solder joints that has been observed in drop testing as well as the high cost of the Ag itself. Therefore, low-Ag-content SAC alloy was considered as a solution for both issues. However, this approach may compromise the thermal-cycling performance of the solders. Therefore, to enhance the thermal-cycling reliability of low-Ag-content SAC alloys without sacrificing their drop-impact performance, alloying elements such as Mn, Ce, Ti, Bi, In, Sb, Ni, Zn, Al, Fe, and Co were selected as additions to these alloys. However, research reports related to these modified SAC alloys are limited. To address this paucity, the present study reviews the effect of these minor alloying elements on the solder joint reliability of low-Ag-content SAC alloys in terms of thermal cycling and drop impact. Addition of Mn, Ce, Bi, and Ni to low-Ag-content SAC solder effectively improves the thermal-cycling reliability of joints without sacrificing the drop-impact performance. Taking into consideration the improvement in the bulk alloy microstructure and mechanical properties, wetting properties, and growth suppression of the interface intermetallic compound (IMC) layers, addition of Ti, In, Sb, Zn, Al, Fe, and Co to low-Ag-content SAC solder has the potential to improve the thermal-cycling reliability of joints without sacrificing the drop-impact performance. Consequently, further investigations of both thermal-cycling and drop reliability of these modified solder joints must be carried out in future work.

  3. Manipulation of charge carrier injection into organic field-effect transistors by self-assembled monolayers of alkanethiols

    NARCIS (Netherlands)

    Asadi, K.; Gholamrezaie, F.; Smits, E.C.P.; Blom, W.M.; Boer, B. de

    2007-01-01

    Charge carrier injection into two semiconducting polymers is investigated in field-effect transistors using gold source and drain electrodes that are modified by self-assembled monolayers of alkanethiols and perfluorinated alkanethiols. The presence of an interfacial dipole associated with the molec

  4. Organic chemistry on surfaces: Direct cyclopropanation by dihalocarbene addition to vinyl terminated self-assembled monolayers (SAMs

    Directory of Open Access Journals (Sweden)

    Malgorzata Adamkiewicz

    2014-12-01

    Full Text Available C11-Vinyl-terminated self-assembled monolayers (SAMs on silica surfaces are successfully modified in C–C bond forming reactions with dihalocarbenes to generate SAMs, terminated with dihalo- (fluoro, chloro, bromo cyclopropane motifs with about 30% surface coverage.

  5. Organic chemistry on surfaces: Direct cyclopropanation by dihalocarbene addition to vinyl terminated self-assembled monolayers (SAMs).

    Science.gov (United States)

    Adamkiewicz, Malgorzata; O'Hagan, David; Hähner, Georg

    2014-01-01

    C11-Vinyl-terminated self-assembled monolayers (SAMs) on silica surfaces are successfully modified in C-C bond forming reactions with dihalocarbenes to generate SAMs, terminated with dihalo- (fluoro, chloro, bromo) cyclopropane motifs with about 30% surface coverage.

  6. Organic chemistry on surfaces: Direct cyclopropanation by dihalocarbene addition to vinyl terminated self-assembled monolayers (SAMs)

    Science.gov (United States)

    Adamkiewicz, Malgorzata

    2014-01-01

    Summary C11-Vinyl-terminated self-assembled monolayers (SAMs) on silica surfaces are successfully modified in C–C bond forming reactions with dihalocarbenes to generate SAMs, terminated with dihalo- (fluoro, chloro, bromo) cyclopropane motifs with about 30% surface coverage. PMID:25550756

  7. High-Quality Alkyl Monolayers on Silicon Surfaces

    NARCIS (Netherlands)

    Sieval, A.B.; Linke, R.; Zuilhof, H.; Sudh"lter, E.J.R.

    2000-01-01

    Covalent attachment of functionalized monolayers onto silicon surfaces (see Figure for examples) is presented here as a strategy for surface modification. The preparation and structure of both unfunctionalized and functionalized alkyl-based monolayers are described, as are potential applications,

  8. Two-photon Photo-emission of Ultrathin Film PTCDA Morphologies on Ag(111)

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Aram; Yang, Aram; Shipman, Steven T.; Garrett-Roe, Sean; Johns, James; Strader, Matt; Szymanski, Paul; Muller, Eric; Harris, Charles B.

    2007-11-29

    Morphology- and layer-dependent electronic structure and dynamics at the PTCDA/Ag(111) interface have been studied with angle-resolved two-photon photoemission. In Stranski-Krastanov growth modes, the exposed wetting layer inhibited the evolution of the vacuum level and valence band to bulk values. For layer-by-layer growth, we observed the transition of electron structure from monolayer to bulk values within eight monolayers. Effective masses and lifetimes of the conduction band and the n=1 image potential state were measured to be larger for disordered layers. The effective mass was interpreted in the context of charge mobility measurements.

  9. Photoluminescence of monolayer MoS2 on LaAlO3 and SrTiO3 substrates.

    Science.gov (United States)

    Li, Yuanyuan; Qi, Zeming; Liu, Miao; Wang, Yuyin; Cheng, Xuerui; Zhang, Guobin; Sheng, Liusi

    2014-12-21

    In an atomically thin-film/dielectric-substrate heterostructure, the elemental physical properties of the atomically thin-film are influenced by the interaction between the thin-film and the substrate. In this article, utilizing monolayer MoS(2) on LaAlO(3) and SrTiO(3) substrates, as well as SiO2 and Gel-film as reference substrates similar to previously reported work [Nano Res, 2014, 7, 561], we systematically investigate the substrate effect on the photoluminescence of monolayer MoS(2). We observed significantly substrate-dependant photoluminescence of monolayer MoS(2), originating from substrate-to-film charge transfer. We found that SiO2 substrate introduces the most charge doping while SrTiO(3) introduces less charge transfer. Through the selection of desired substrate, we are able to induce different amounts of charge into the monolayer MoS(2), which consequently modifies the neutral exciton and charged exciton (trion) emissions. Finally, we proposed a band-diagram model to elucidate the relation between charge transfer and the substrate Fermi level and work function. Our work demonstrates that the substrate charge transfer exerts a strong influence on the monolayer MoS(2) photoluminescence property, which should be considered during device design and application. The work also provides a possible route to modify the thin-film photoluminescence property via substrate engineering for future device design.

  10. Modification of degenerative photoluminescence in aged monolayer WSsub>2sub> by PCsub>61sub>BM surface processing.

    Science.gov (United States)

    Liu, Yu; Zheng, Xin; Li, Han; Xu, Zhongjie; Jiang, Tian

    2017-02-01

    Owing to their unique physical properties, monolayer transition metal dichalcogenides (TMDCs) have been widely used in applications of light-emitting diodes (LEDs). However, monolayers of TMDCs undergo dramatic aging effects, including intense degradation in optical behavior, extensive cracking, and severe quenching of the direct gap photoluminescence (PL), seriously limiting the device performance. In this work, we show that monolayer WSsub>2sub> stored for three months even in the glovebox exhibits obvious degenerative PL with changed peak position that can be attributed to the presence of a large number of trions induced by the aging effect. PCsub>61sub>BM surface processing was used to modify the surface of the aged monolayer WSsub>2sub>. As expected, higher uniformity in the PL spectrum was obtained. Besides, the PL peak wavelength was modified to be the same as that of the nonaged one and did not change even at higher excitation power. This strategy is shown to successfully suppress the formation of the trion by transferring the excess electrons from WSsub>2sub> to PCsub>61sub>BM. The results demonstrate the feasibility of applying PCsub>61sub>BM surface modification to improve the performance of the LED based on monolayer WSsub>2sub>.

  11. N-Hydroxysuccinimide-terminated self-assembled monolayers on gold for biomolecules immobilisation

    Energy Technology Data Exchange (ETDEWEB)

    Cabrita, J.F. [Laboratorio de SPM, Faculdade de Ciencias da Universidade de Lisboa, Ed. ICAT, Campo Grande, 1749-016 Lisbon (Portugal); CQB, Departamento de Quimica e Bioquimica da Faculdade de Ciencias da Universidade de Lisboa, Campo Grande, 1749-016 Lisbon (Portugal); Abrantes, L.M. [Laboratorio de SPM, Faculdade de Ciencias da Universidade de Lisboa, Ed. ICAT, Campo Grande, 1749-016 Lisbon (Portugal); CQB, Departamento de Quimica e Bioquimica da Faculdade de Ciencias da Universidade de Lisboa, Campo Grande, 1749-016 Lisbon (Portugal); Viana, A.S. [Laboratorio de SPM, Faculdade de Ciencias da Universidade de Lisboa, Ed. ICAT, Campo Grande, 1749-016 Lisbon (Portugal)]. E-mail: anaviana@icat.fc.ul.pt

    2005-03-15

    Pure and mixed N-hydroxysuccinimide-terminated and butanethiol monolayers were prepared on flat gold (1 1 1) surfaces with the intent of developing suitable platforms for the direct biomolecules immobilisation. The self-assembled monolayers (SAMs) were characterised by electrochemical reductive desorption of the thiolate from the gold surface. The data have shown that certain solution proportions of the two compounds yield modified electrodes exhibiting intermediate electrochemical behaviour of the corresponding pure SAMs. The reactivity of the terminal N-hydroxysuccinimide (NHS) towards amine functionalities has been tested for the covalent attachment of Dopamine. The cyclic voltammetric responses of the investigated monolayers, after contacting with a Dopamine solution, have confirmed the chemical coupling of the amine as well as the formation of mixed SAMs. The Dopamine surface coverage increased with the amount of surface NHS. Laccase was also successfully immobilised onto this modified electrodes. The electrochemical behaviour of the modified SAMs with Laccase indicates direct electron transfer between the immobilised enzyme and the gold surface. Evidence for Laccase immobilisation was also provided by atomic force microscopic measurements.

  12. Ag/lamellar hosts composites: a route to morphology-controllable synthesis of Ag nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Luiz P. da; Quites, Fernando J.; Sigoli, Fernando A.; Mazali, Italo O., E-mail: mazali@iqm.unicamp.br; Pastore, Heloise O., E-mail: gpmmm@iqm.unicamp.br [University of Campinas (UNICAMP), Institute of Chemistry (Brazil)

    2013-08-15

    An easy and novel routine are reported for the preparation of metallic silver nanoparticles (AgNPs) with controlled morphology, using Na{sup +}-magadiite swelled with hexadecyltrimethylammonium bromide (CTA{sup +}-magadiite) and a layered aluminophosphate with kanemite-type structure modified with n-dodecylammonium and n-butylammonium (but,dod-AlPO-kan) as hosts. For the preparation of the metallic AgNPs (Ag{sup 0}) in the interlamellar space, the CTA{sup +}-magadiite and but,dod-AlPO-kan hosts were dispersed in N,N-dimethylformamide (DMF) solution with different AgNO{sub 3} concentrations. DMF acts as reducing agent of Ag{sup +} ions leading to nanoparticles with disk-like morphology of magadiite silicate; these were characterized by TEM and UV-Vis spectroscopy. On the other hand, the AgNPs are intercalated in but,dod-AlPO-kan showing spherical-like morphology. The UV-Vis spectra of the nanocomposites based on Ag{sup 0} and magadiite silicate show bands at 565 nm that can be attributed to Ag{sup 0} nanodisks. The Ag-but,dod-AlPO-kan-based nanocomposites present a band at 422 nm attributed to the surface plasmon resonance of Ag{sup 0} nanospheres. The results of transmission electron microscopy agree very well with XRD and UV-Vis analysis, indicating the formation of AgNPs with different morphologies using the two kinds of lamellar materials. The magadiite host has an important role in the synthesis of Ag nanodisks, because it controls the growth of nanoparticles inside the interlayer region with disk-like morphology due the high interlayer interactions of the silicate, leading to the growth of nanoparticles in only two directions (xy plane). On the other hand, when but,dod-AlPO-kan is used a sphere-like morphology is preferred due the best accommodation of AgNPs between the layers of aluminophosphate host.

  13. Study of Ag induced bimetallic (Au-Ag) nanowires on silicon (5 5 12) surfaces: Experiment and theoretical aspects

    Science.gov (United States)

    Bhukta, Anjan; Bagarti, Trilochan; Guha, Puspendu; Ravulapalli, Sathyavathi; Satpati, Biswarup; Rakshit, Bipul; Maiti, Paramita; Parlapalli, Venkata Satyam

    2017-10-01

    The reconstructed vicinal (high index) silicon surfaces, such as, Si (5 5 12) composes row-like structures that can be used as templates for growing aligned nanowires. By using a sub-monolayers of Ag, prior to Au deposition on reconstructed Si (5 512) surface, intermixing of Au and Ag, enhancement of aspect ratio of bimetallic Au-Ag nanowires with tunable morphology is reported. This is attributed to a combined effect of pre-grown Ag strips as nucleation centers for incoming Au ad-atoms and anisotropic Au-Ag intermixing. To achieve optimum conditions for the growth of larger aspect ratio Au-Ag nanostructures, the growth kinetics have been studied by varying growth and annealing temperatures. At ≈400 °C, the Ag diffused into silicon substrate and the inter-diffusion found to inhibit the formation of Au-Ag bimetallic nanostructures. Controlled experiments under ultra-high vacuum condition in a molecular beam epitaxy system and in-situ scanning tunneling microscopy measurements along with ex-situ scanning transmission and secondary electron microscopy measurements have been carried out to understand the bimetallic nanostructure growth. Kinetic Monte Carlo (KMC) simulations based on kinematics of ad-atoms on an anisotropic template with a solid on solid model in which the relative ratios of binding energies (that are obtained from the Density Functional Theory) have been used and the KMC simulations results agree with the experimental observations. Advantage of having bimetallic structures as effective substrates for Surface enhanced Raman spectroscopy application is demonstrated by detecting Rhodamine 6 G (R6G) molecule at the concentration of 10-7M.

  14. An Ab Initio Study of the Low-Lying Doublet States of AgO and AgS

    Science.gov (United States)

    Bauschlicher, Charles W., Jr.; Partridge, Harry; Langhoff, Stephen R.

    1990-01-01

    Spectroscopic constants (D(sub o), r(sub e), mu(sub e), T(sub e)) are determined for the doublet states of AgO and AgS below approx. = 30000/cm. Large valence basis sets are employed in conjunction with relativistic effective core potentials (RECPs). Electron correlation is included using the modified coupled-pair functional (MCPF) and multireference configuration interaction (MRCI) methods. The A(sup 2)Sigma(sup +) - X(sup 2)Pi band system is found to occur in the near infrared (approx. = 9000/cm) and to be relatively weak with a radiative lifetime of 900 microns for A(sup 2)Sigma(sup +) (upsilon = 0). The weakly bound C(sup 2)Pi state (our notation), the upper state of the blue system, is found to require high levels of theoretical treatment to determine a quantitatively accurate potential. The red system is assigned as a transition from the C(sup 2)Pi state to the previously unobserved A(sup 2)Sigma(sup +) state. Several additional transitions are identified that should be detectable experimentally. A more limited study is performed for the vertical excitation spectrum of AgS. In addition, a detailed all-electron study of the X(sup 2)Pi and A(sup 2)Sigma(sup +) states of AgO is carried out using large atomic natural orbital (ANO) basis sets. Our best calculated D(sub o) value for AgO is significantly less than the experimental value, which suggests that there may be some systematic error in the experimental determination.

  15. Glitter in a 2D monolayer.

    Science.gov (United States)

    Yang, Li-Ming; Dornfeld, Matthew; Frauenheim, Thomas; Ganz, Eric

    2015-10-21

    We predict a highly stable and robust atomically thin gold monolayer with a hexagonal close packed lattice stabilized by metallic bonding with contributions from strong relativistic effects and aurophilic interactions. We have shown that the framework of the Au monolayer can survive 10 ps MD annealing simulations up to 1400 K. The framework is also able to survive large motions out of the plane. Due to the smaller number of bonds per atom in the 2D layer compared to the 3D bulk we observe significantly enhanced energy per bond (0.94 vs. 0.52 eV per bond). This is similar to the increase in bond strength going from 3D diamond to 2D graphene. It is a non-magnetic metal, and was found to be the global minima in the 2D space. Phonon dispersion calculations demonstrate high kinetic stability with no negative modes. This 2D gold monolayer corresponds to the top monolayer of the bulk Au(111) face-centered cubic lattice. The close-packed lattice maximizes the aurophilic interactions. We find that the electrons are completely delocalized in the plane and behave as 2D nearly free electron gas. We hope that the present work can inspire the experimental fabrication of novel free standing 2D metal systems.

  16. Nanotubes based on monolayer blue phosphorus

    KAUST Repository

    Montes Muñoz, Enrique

    2016-07-08

    We demonstrate structural stability of monolayer zigzag and armchair blue phosphorus nanotubes by means of molecular dynamics simulations. The vibrational spectrum and electronic band structure are determined and analyzed as functions of the tube diameter and axial strain. The nanotubes are found to be semiconductors with a sensitive indirect band gap that allows flexible tuning.

  17. Non-rotator phases in phospholipid monolayers?

    DEFF Research Database (Denmark)

    Kenn, R.M.; Kjær, K.; Möhwald, H.

    1996-01-01

    Monolayers of diacylphosphatidylethanolamines at the air/water interface are studied by grazing incidence X-ray diffraction. The results prove the existence of phases which show analogies with the rotator phases of single-chain surfactants: hexagonal tail lattice with no tilt; rectangular lattice...

  18. Statistical mechanics of a lipid monolayer

    NARCIS (Netherlands)

    Kox, A.J.; Wiegel, F.W.

    1978-01-01

    We calculate from first principles the equation of state of a simple type of membrane: a monolayer consisting of lipid chain molecules with short-range repulsive and long-range attractive forces. An approximate solution to the packing problem of the hydrocarbon chains is obtained by using a mathemat

  19. Semiconductor monolayer assemblies with oriented crystal faces

    KAUST Repository

    Ma, Guijun

    2012-01-01

    Fabrication of two-dimensional monolayers of crystalline oxide and oxynitride particles was attempted on glass plate substrates. X-Ray diffraction patterns of the assemblies show only specific crystal facets, indicative of the uniform orientation of the particles on the substrate. The selectivity afforded by this immobilization technique enables the organization of randomly distributed polycrystalline powders in a controlled manner.

  20. Structure of cholesterol/ceramide monolayer mixtures

    DEFF Research Database (Denmark)

    Scheffer, L.; Solomonov, I.; Weygand, M.J.

    2005-01-01

    The structure of monolayers of cholesterol/ ceramide mixtures was investigated using grazing incidence x-ray diffraction, immunofluorescence, and atomic force microscopy techniques. Grazing incidence x-ray diffraction measurements showed the existence of a crystalline mixed phase of the two...

  1. Edge conduction in monolayer WTe2

    Science.gov (United States)

    Fei, Zaiyao; Palomaki, Tauno; Wu, Sanfeng; Zhao, Wenjin; Cai, Xinghan; Sun, Bosong; Nguyen, Paul; Finney, Joseph; Xu, Xiaodong; Cobden, David H.

    2017-07-01

    A two-dimensional topological insulator (2DTI) is guaranteed to have a helical one-dimensional edge mode in which spin is locked to momentum, producing the quantum spin Hall effect and prohibiting elastic backscattering at zero magnetic field. No monolayer material has yet been shown to be a 2DTI, but recently the Weyl semimetal WTe2 was predicted to become a 2DTI in monolayer form if a bulk gap opens. Here, we report that, at temperatures below about 100 K, monolayer WTe2 does become insulating in its interior, while the edges still conduct. The edge conduction is strongly suppressed by an in-plane magnetic field and is independent of gate voltage, save for mesoscopic fluctuations that grow on cooling due to a zero-bias anomaly, which reduces the linear-response conductance. Bilayer WTe2 also becomes insulating at low temperatures but does not show edge conduction. Many of these observations are consistent with monolayer WTe2 being a 2DTI. However, the low-temperature edge conductance, for contacts spacings down to 150 nm, never reaches values higher than ~20 μS, about half the predicted value of e2/h, suggesting significant elastic scattering in the edge.

  2. Adsorption of Ions at Uncharged Insoluble Monolayers

    Science.gov (United States)

    Peshkova, T. V.; Minkov, I. L.; Tsekov, R.; Slavchov, R. I.

    2016-08-01

    A method is proposed for the experimental determination of the adsorption of inorganic electrolytes at a surface covered with insoluble surfactant monolayer. This task is complicated by the fact that the change of the salt concentration alters both chemical potentials of the electrolyte and the surfactant. Our method resolves the question by combining data for the surface pressure versus area of the monolayer at several salt concentrations with data for the equilibrium spreading pressure of crystals of the surfactant (used to fix a standard state). We applied the method to alcohols spread at the surface of concentrated halide solutions. The measured salt adsorption is positive and has nonmonotonic dependence on the area per surfactant molecule. For the liquid expanded film, depending on the concentration, there is one couple of ions adsorbed per each 3–30 surfactant molecules. We analyzed which ion, the positive or the negative, stands closer to the surface, by measuring the effect of NaCl on the Volta potential of the monolayer. The potentiometric data suggest that Na+ is specifically adsorbed, while Cl– remains in the diffuse layer, i.e., the surface is positively charged. The observed reverse Hofmeister series of the adsorptions of NaF, NaCl, and NaBr suggests the same conclusion holds for all these salts. The force that causes the adsorption of Na+ seems to be the interaction of the ion with the dipole moment of the monolayer.

  3. Penetration of lipid monolayers by psychoactive drugs

    NARCIS (Netherlands)

    Demel, R.A.; Deenen, L.L.M. van

    1966-01-01

    The ability of a number of psychoactive drugs to penetrate lipid monolayers of varying composition was examined, and the following observation were made: (1) The increase in surface pressure of a monomolecular film appeared to depend on the chemical nature of the lipid as well as on the initial film

  4. Molecular diffusion in monolayer and submonolayer nitrogen

    DEFF Research Database (Denmark)

    Hansen, Flemming Yssing; Bruch, Ludwig Walter

    2001-01-01

    The orientational and translational motions in a monolayer fluid of physisorbed molecular nitrogen are treated using molecular dynamics simulations. Dynamical response functions and several approximations to the coefficient of translational diffusion are determined for adsorption on the basal pla...... where the ballistic approximation to the translational molecular self-correlation function is accurate....

  5. AGS experiments: 1993 - 1994 - 1995

    Energy Technology Data Exchange (ETDEWEB)

    Depken, J.C.

    1996-04-01

    This report contains: FY 1995 AGS Schedule as Run; FY 1996-97 AGE Schedule (working copy); AGS Beams 1995; AGS Experimental Area FY 1993 Physics Program; AGS Experimental Area FY 1994 Physics Program; AGS Experimental Area FY 1995 Physics Program; AGS Experimental Area FY 1996 Physics Program (In progress); A listing of experiments by number; Two-page summaries of each experiment begin here, also ordered by number; Listing of publications of AGS experiments begins here; and Listing of AGS experimenters begins here. This is the twelfth edition.

  6. Fluorinated alkyne-derived monolayers on oxide-free silicon nanowires via one-step hydrosilylation

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen Minh, Quyen [Laboratory of Organic Chemistry, Wageningen University, Stippeneng 4, 6708 WE Wageningen (Netherlands); Nanosens, IJsselkade 7, 7201 HB Zutphen (Netherlands); Pujari, Sidharam P. [Laboratory of Organic Chemistry, Wageningen University, Stippeneng 4, 6708 WE Wageningen (Netherlands); Wang, Bin [The Department of Chemical Engineering and Russell Berrie Nanotechnology Institute, Technion – Israel Institute of Technology, Haifa 3200003 (Israel); Wang, Zhanhua [Laboratory of Organic Chemistry, Wageningen University, Stippeneng 4, 6708 WE Wageningen (Netherlands); Haick, Hossam [The Department of Chemical Engineering and Russell Berrie Nanotechnology Institute, Technion – Israel Institute of Technology, Haifa 3200003 (Israel); Zuilhof, Han [Laboratory of Organic Chemistry, Wageningen University, Stippeneng 4, 6708 WE Wageningen (Netherlands); Rijn, Cees J.M. van, E-mail: cees.vanrijn@wur.nl [Laboratory of Organic Chemistry, Wageningen University, Stippeneng 4, 6708 WE Wageningen (Netherlands)

    2016-11-30

    Highlights: • Oxide-free H-terminated silicon nanowires undergo efficient surface modification by reaction with fluorinated 1-alkynes (HC≡C−(CH{sub 2}){sub 6}C{sub 8}H{sub 17−x}F{sub x}; x = 0–17). • These surface-modified Si NWs are chemically stable under range of conditions (including acid, base). • The surface coating yields efficient electrical passivation as demonstrated by a near-zero electrochemical activity of the surface. - Abstract: Passivation of oxide-free silicon nanowires (Si NWs) by the formation of high-quality fluorinated 1-hexadecyne-derived monolayers with varying fluorine content has been investigated. Alkyl chain monolayers (C{sub 16}H{sub 30−x}F{sub x}) with a varying number of fluorine substituents (x = 0, 1, 3, 9, 17) were attached onto hydrogen-terminated silicon (Si−H) surfaces with an effective one-step hydrosilylation. This surface chemistry gives well-defined monolayers on nanowires that have a cylindrical core–shell structure, as characterized by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR) and static contact angle (SCA) analysis. The monolayers were stable under acidic and basic conditions, as well as under extreme conditions (such as UV exposure), and provide excellent surface passivation, which opens up applications in the fields of field effect transistors, optoelectronics and especially for disease diagnosis.

  7. Cu2+、Ag+掺杂改性TiO2固体超强酸的制备及光催化降解偏二甲肼废水研究%Study on Preparation of TiO2 Solid Superacids Modified by Doping Cu2+,Ag+ and Photo-catalytic Degradation of UDMH Wastewater

    Institute of Scientific and Technical Information of China (English)

    梁峰豪; 贾瑛; 贺亚楠; 侯若梦

    2013-01-01

    采用溶胶-凝胶法制备了SO2-/TiO2-Cu2+和SO2-/TiO2-Ag+2种固体超强酸催化剂,并用电子显微镜、X射线衍射仪等对制备的催化剂进行了表征.实验考察了2种催化剂体系光催化降解偏二甲肼(UDMH)废水的效果和主要影响因素.实验结果表明,固体超强酸SO42-/TiO2-Cu2+光催化降解UDMH废水比SO2-/TiO2-Ag+体系的降解效果更好.在最优反应条件溶液pH=7~8,SO2-/TiO2-Cu2+投加量为0.1 g/L下,初始浓度400 mg/L的UDMH废水,在磁力搅拌模拟超重力条件下反应30 min后,UDMH的降解率达到了96%以上.

  8. Ligand Replacement Approach to Raman-Responded Molecularly Imprinted Monolayer for Rapid Determination of Penicilloic Acid in Penicillin.

    Science.gov (United States)

    Zhang, Liying; Jin, Yang; Huang, Xiaoyan; Zhou, Yujie; Du, Shuhu; Zhang, Zhongping

    2015-12-01

    Penicilloic acid (PA) is a degraded byproduct of penicillin and often causes fatal allergies to humans, but its rapid detection in penicillin drugs remains a challenge due to its similarity to the mother structure of penicillin. Here, we reported a ligand-replaced molecularly imprinted monolayer strategy on a surface-enhanced Raman scattering (SERS) substrate for the specific recognition and rapid detection of Raman-inactive PA in penicillin. The bis(phenylenediamine)-Cu(2+)-PA complex was first synthesized and stabilized onto the surface of silver nanoparticle film that was fabricated by a bromide ion-added silver mirror reaction. A molecularly imprinted monolayer was formed by the further modification of alkanethiol around the stabilized complex on the Ag film substrate, and the imprinted recognition site was then created by the replacement of the complex template with Raman-active probe molecule p-aminothiophenol. When PA rebound into the imprinted site in the alkanethiol monolayer, the SERS signal of p-aminothiophenol exhibited remarkable enhancement with a detection limit of 0.10 nM. The imprinted monolayer can efficiently exclude the interference of penicillin and thus provides a selective determination of 0.10‰ (w/w) PA in penicillin, which is about 1 order of magnitude lower than the prescribed residual amount of 1.0‰. The strategy reported here is simple, rapid and inexpensive compared to the traditional chromatography-based methods.

  9. Formation of the BiAg2 surface alloy on lattice-mismatched interfaces

    Science.gov (United States)

    Abd El-Fattah, Z. M.; Lutz, P.; Piquero-Zulaica, I.; Lobo-Checa, J.; Schiller, F.; Bentmann, H.; Ortega, J. E.; Reinert, F.

    2016-10-01

    We report on the growth of a monolayer-thick BiAg2 surface alloy on thin Ag films grown on Pt(111) and Cu(111). Using low energy electron diffraction (LEED), angle resolved photoemission spectroscopy (ARPES), and scanning tunneling microscopy (STM) we show that the surface structure of the 1/3 ML Bi/x -ML Ag/Pt(111) system (x ≥2 ) is strongly affected by the annealing temperature required to form the alloy. As judged from the characteristic (√{3 }×√{3 } )R 30∘ LEED pattern, the BiAg2 alloy is partially formed at room temperature. A gentle, gradual increase in the annealing temperatures successively results in the formation of a pure BiAg2 phase, a combination of that phase with a (2 ×2 ) superstructure, and finally the pure (2 ×2 ) phase, which persists at higher annealing temperatures. These results complement recent work reporting the (2 ×2 ) as a predominant phase, and attributing the absence of BiAg2 alloy to the strained Ag/Pt interface. Likewise, we show that the growth of the BiAg2 alloy on similarly lattice-mismatched 1 and 2 ML Ag-Cu(111) interfaces also requires a low annealing temperature, whilst higher temperatures result in BiAg2 clustering and the formation of a BiCu2 alloy. The demonstration that the BiAg2 alloy can be formed on thin Ag films on different substrates presenting a strained interface has the prospect of serving as bases for technologically relevant systems, such as Rashba alloys interfaced with magnetic and semiconductor substrates.

  10. Photoelectrocatalytic oxidation of GMP on an ITO electrode modified with clay/[Ru(phen)2(dC18bpy)]2+ hybrid film

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    An indium tin oxide (ITO) electrode modified with monolayer clay/[Ru(phen)2(dC18bpy)]2+ (phen= 1,10-phenanthroline, dC18bpy = 4,4′-dioctadecyl-2,2′ bipyridyl) hybrid film has been fabricated by the Langmuir-Blodgett (LB) method. Atomic force microscopy revealed that the single-layered hybrid film of clay/[Ru(phen)2(dC18bpy)]2+ (denoted as Clay-Ru) was closely packed at a surface pressure of 25 mN-m-1 and had a thickness of 3.4±0.5 nm. Cyclic voltammograms showed that the redox current of Ru(Ⅱ) complex decreased when incorporated into the clay film, suggesting that the clay layer acts as a barrier against electron transfer. When applied to oxidizing the mononucleotide of guanosine 5′-monophosphate (GMP), a large catalytic oxidative current was achieved on the Clay-Ru(Ⅱ) modified ITO electrode at the external potential above 900 mV (vs. Ag|AgCl|KCl ) and, more significantly, this response was further enhanced by light irradiation (λ>360 nm), in which the photocurrent is increased about 11 times in comparison with that of a bare ITO. Mechanism of the photoelectrocatalytic effect was proposed in terms of the reduction of the photoelectrochemically generated Ru(Ⅲ) complex in the Clay-Ru film by GMP.

  11. Electrodeposition of gold templated by patterned thiol monolayers

    Energy Technology Data Exchange (ETDEWEB)

    She, Zhe [EaStCHEM School of Chemistry, University of St. Andrews, KY16 9ST (United Kingdom); Di Falco, Andrea [SUPA, School of Physics and Astronomy, University of St. Andrews, KY16 9SS (United Kingdom); Hähner, Georg [EaStCHEM School of Chemistry, University of St. Andrews, KY16 9ST (United Kingdom); Buck, Manfred, E-mail: mb45@st-andrews.ac.uk [EaStCHEM School of Chemistry, University of St. Andrews, KY16 9ST (United Kingdom)

    2016-06-15

    Graphical abstract: - Highlights: • First demonstration of electrodeposition/lift-off of gold using thiol monolayers. • Microelectrode structures with large length to width ratio were generated. • Performance of two different patterning techniques was investigated. • Conditions for achieving good contrast in the electrodeposition were established. - Abstract: The electrochemical deposition of Au onto Au substrates modified by self-assembled monolayers (SAMs) was studied by linear sweep voltammetry (LSV), atomic force microscopy (AFM) and scanning electron microscopy (SEM). Patterned SAMs exhibiting electrochemical contrast were prepared by two different methods. One used microcontact printing (μCP) to generate a binary SAM of ω-(4′-methyl-biphenyl-4-yl)-propane thiol (CH{sub 3}-C{sub 6}H{sub 4}-C{sub 6}H{sub 4}-(CH{sub 2}){sub 3}-SH, MBP3) and octadecane thiol (CH{sub 3}(CH{sub 2}){sub 17}SH, ODT). Templated by the SAM, a gold microelectrode structure was electrodeposited featuring a line 15 μm wide and 3 mm long. After transfer to an epoxy substrate the structure proved to be electrically conductive across the full length. The other patterning method applied electron beam lithography (EBL) where electrochemical contrast was achieved by crosslinking molecules in a single component SAM of MBP3. An electron dose above 250 mC/cm{sup 2} results in a high deposition contrast. The choice of parameters for the deposition/lift-off process is found to be more critical for Au compared to Cu studied previously. The origin of the differences and implications for nanoscale patterning are discussed.

  12. Transport measurement of Li doped monolayer graphene

    Science.gov (United States)

    Khademi, Ali; Sajadi, Ebrahim; Dosanjh, Pinder; Folk, Joshua; Stöhr, Alexander; Forti, Stiven; Starke, Ulrich

    Lithium adatoms on monolayer graphene have been predicted to induce superconductivity with a critical temperature near 8 K, and recent experimental evidence by ARPES indicates a critical temperature nearly that high. Encouraged by these results, we investigated the effects of lithium deposited at cryogenic temperatures on the electronic transport properties of epitaxial and CVD monolayer graphene down to 3 K. The change of charge carrier density due to Li deposition was monitored both by the gate voltage shift of the Dirac point and by Hall measurements, in low and high doping regimes. In the high doping regime, a saturation density of 2×1013 cm-2 was observed independent of sample type, initial carrier density and deposition conditions. No signatures of superconductivity were observed down to 3 K.

  13. Fracture Characteristics of Monolayer CVD-Graphene

    Science.gov (United States)

    Hwangbo, Yun; Lee, Choong-Kwang; Kim, Sang-Min; Kim, Jae-Hyun; Kim, Kwang-Seop; Jang, Bongkyun; Lee, Hak-Joo; Lee, Seoung-Ki; Kim, Seong-Su; Ahn, Jong-Hyun; Lee, Seung-Mo

    2014-03-01

    We have observed and analyzed the fracture characteristics of the monolayer CVD-graphene using pressure bulge testing setup. The monolayer CVD-graphene has appeared to undergo environmentally assisted subcritical crack growth in room condition, i.e. stress corrosion cracking arising from the adsorption of water vapor on the graphene and the subsequent chemical reactions. The crack propagation in graphene has appeared to be able to be reasonably tamed by adjusting applied humidity and stress. The fracture toughness, describing the ability of a material containing inherent flaws to resist catastrophic failure, of the CVD-graphene has turned out to be exceptionally high, as compared to other carbon based 3D materials. These results imply that the CVD-graphene could be an ideal candidate as a structural material notwithstanding environmental susceptibility. In addition, the measurements reported here suggest that specific non-continuum fracture behaviors occurring in 2D monoatomic structures can be macroscopically well visualized and characterized.

  14. Molecular tilt on monolayer-protected nanoparticles

    KAUST Repository

    Giomi, L.

    2012-02-01

    The structure of the tilted phase of monolayer-protected nanoparticles is investigated by means of a simple Ginzburg-Landau model. The theory contains two dimensionless parameters representing the preferential tilt angle and the ratio ε between the energy cost due to spatial variations in the tilt of the coating molecules and that of the van der Waals interactions which favors the preferential tilt. We analyze the model for both spherical and octahedral particles. On spherical particles, we find a transition from a tilted phase, at small ε, to a phase where the molecules spontaneously align along the surface normal and tilt disappears. Octahedral particles have an additional phase at small ε characterized by the presence of six topological defects. These defective configurations provide preferred sites for the chemical functionalization of monolayer-protected nanoparticles via place-exchange reactions and their consequent linking to form molecules and bulk materials. Copyright © EPLA, 2012.

  15. The effect of β-sitosterol on the properties of cholesterol/phosphatidylcholine/ganglioside monolayers--the impact of monolayer fluidity.

    Science.gov (United States)

    Hąc-Wydro, Katarzyna

    2013-10-01

    In this paper the influence of one of phytosterols, namely β-sitosterol on cholesterol (Chol)/phosphatidylcholine (PC)/ganglioside (GM3) monolayers was examined to find the correlation between the properties of model system and the effect of phytocompound. The studied monolayers differed in condensation and fluidity, which were modified by the structure of phosphatidylcholine. It was found that the incorporation of β-sitosterol into cholesterol/phosphatidylcholine/ganglioside films changes their morphology, condensation and interactions between the lipids. The substitution of cholesterol more strongly decreased the condensation and stability of the film containing PC molecules having monounsaturated chains than more densely packed monolayer composed of saturated phosphatidylcholine. However, thorough analysis of data obtained so far suggests that the magnitude of β-sitosterol effect is determined by the composition of the system rather than its fluidity itself. Moreover, the results collected herein correlate well with the findings that phytosterol more strongly inhibits the growth of cancer cells, which at a given proportion of cholesterol to phospholipids in membranes, have more unsaturated fatty acids within phospholipids molecules.

  16. Tandem "click" reactions at acetylene-terminated Si(100) monolayers.

    Science.gov (United States)

    Ciampi, Simone; James, Michael; Michaels, Pauline; Gooding, J Justin

    2011-06-07

    We demonstrate a simple method for coupling alkynes to alkynes. The method involves tandem azide-alkyne cycloaddition reactions ("click" chemistry) for the immobilization of 1-alkyne species onto an alkyne modified surface in a one-pot procedure. In the case presented, these reactions take place on a nonoxidized Si(100) surface although the approach is general for linking alkynes to alkynes. The applicability of the method in the preparation of electrically well-behaved functionalized surfaces is demonstrated by coupling an alkyne-tagged ferrocene species onto alkyne-terminated Si(100) surfaces. The utility of the approach in biotechnology is shown by constructing a DNA sensing interface by derivatization of the acetylenyl surface with commercially available alkyne-tagged oligonucleotides. Cyclic voltametry, electrochemical impedance spectroscopy, X-ray photoelectron spectroscopy, and X-ray reflectometry are used to characterize the coupling reactions and performance of the final modified surfaces. These data show that this synthetic protocol gives chemically well-defined, electronically well-behaved, and robust (bio)functionalized monolayers on silicon semiconducting surfaces.

  17. Physiological hydrostatic pressure protects endothelial monolayer integrity.

    Science.gov (United States)

    Müller-Marschhausen, K; Waschke, J; Drenckhahn, D

    2008-01-01

    Endothelial monolayer integrity is required to maintain endothelial barrier functions and has found to be impaired in several disorders like inflammatory edema, allergic shock, or artherosclerosis. Under physiologic conditions in vivo, endothelial cells are exposed to mechanical forces such as hydrostatic pressure, shear stress, and cyclic stretch. However, insight into the effects of hydrostatic pressure on endothelial cell biology is very limited at present. Therefore, in this study, we tested the hypothesis that physiological hydrostatic pressure protects endothelial monolayer integrity in vitro. We investigated the protective efficacy of hydrostatic pressure in microvascular myocardial endothelial (MyEnd) cells and macrovascular pulmonary artery endothelial cells (PAECs) by the application of selected pharmacological agents known to alter monolayer integrity in the absence or presence of hydrostatic pressure. In both endothelial cell lines, extracellular Ca(2+) depletion by EGTA was followed by a loss of vascular-endothelial cadherin (VE-caherin) immunostaining at cell junctions. However, hydrostatic pressure (15 cmH(2)O) blocked this effect of EGTA. Similarly, cytochalasin D-induced actin depolymerization and intercellular gap formation and cell detachment in response to the Ca(2+)/calmodulin antagonist trifluperazine (TFP) as well as thrombin-induced cell dissociation were also reduced by hydrostatic pressure. Moreover, hydrostatic pressure significantly reduced the loss of VE-cadherin-mediated adhesion in response to EGTA, cytochalasin D, and TFP in MyEnd cells as determined by laser tweezer trapping using VE-cadherin-coated microbeads. In caveolin-1-deficient MyEnd cells, which lack caveolae, hydrostatic pressure did not protect monolayer integrity compromised by EGTA, indicating that caveolae-dependent mechanisms are involved in hydrostatic pressure sensing and signaling.

  18. Elasticity of a quantum monolayer solid

    DEFF Research Database (Denmark)

    Bruch, Ludwig Walter

    1992-01-01

    A perturbation-theory formulation of the zero-temperature elastic constants is used to verify symmetry relations for a (monolayer) triangluar lattice. A generalization of the Cauchy relation between the two elastic constants of the triangular lattice with central-pair-potential interactions is gi...... is given for the quantum solid. The first-order quantum corrections are rederived in this formalism, and previous calculations are reanalyzed....

  19. Strain mapping in a graphene monolayer nanocomposite.

    Science.gov (United States)

    Young, Robert J; Gong, Lei; Kinloch, Ian A; Riaz, Ibtsam; Jalil, Rashed; Novoselov, Kostya S

    2011-04-26

    Model composite specimens have been prepared consisting of a graphene monolayer sandwiched between two thin layers of polymer on the surface of a poly(methyl methacrylate) beam. It has been found that well-defined Raman spectra can be obtained from the single graphene atomic layer and that stress-induced Raman band shifts enable the strain distribution in the monolayer to be mapped with a high degree of precision. It has been demonstrated that the distribution of strain across the graphene monolayer is relatively uniform at levels of applied strain up to 0.6% but that it becomes highly nonuniform above this strain. The change in the strain distributions has been shown to be due to a fragmentation process due to the development of cracks, most likely in the polymer coating layers, with the graphene remaining intact. The strain distributions in the graphene between the cracks are approximately triangular in shape, and the interfacial shear stress in the fragments is only about 0.25 MPa, which is an order of magnitude lower than the interfacial shear stress before fragmentation. This relatively poor level of adhesion between the graphene and polymer layers has important implications for the use of graphene in nanocomposites, and methods of strengthening the graphene-polymer interface are discussed.

  20. Janus monolayers of transition metal dichalcogenides

    KAUST Repository

    Lu, Ang-Yu

    2017-05-15

    Structural symmetry-breaking plays a crucial role in determining the electronic band structures of two-dimensional materials. Tremendous efforts have been devoted to breaking the in-plane symmetry of graphene with electric fields on AB-stacked bilayers or stacked van der Waals heterostructures. In contrast, transition metal dichalcogenide monolayers are semiconductors with intrinsic in-plane asymmetry, leading to direct electronic bandgaps, distinctive optical properties and great potential in optoelectronics. Apart from their in-plane inversion asymmetry, an additional degree of freedom allowing spin manipulation can be induced by breaking the out-of-plane mirror symmetry with external electric fields or, as theoretically proposed, with an asymmetric out-of-plane structural configuration. Here, we report a synthetic strategy to grow Janus monolayers of transition metal dichalcogenides breaking the out-of-plane structural symmetry. In particular, based on a MoS2 monolayer, we fully replace the top-layer S with Se atoms. We confirm the Janus structure of MoSSe directly by means of scanning transmission electron microscopy and energy-dependent X-ray photoelectron spectroscopy, and prove the existence of vertical dipoles by second harmonic generation and piezoresponse force microscopy measurements.

  1. Investigation on gallium ions impacting monolayer graphene

    Directory of Open Access Journals (Sweden)

    Xin Wu

    2015-06-01

    Full Text Available In this paper, the physical phenomena of gallium (Ga+ ion impacting monolayer graphene in the nanosculpting process are investigated experimentally, and the mechanisms are explained by using Monte Carlo (MC and molecular dynamics (MD simulations. Firstly, the MC method is employed to clarify the phenomena happened to the monolayer graphene target under Ga+ ion irradiation. It is found that substrate has strong influence on the damage mode of graphene. The mean sputtering yield of graphene under 30 keV Ga+ ion irradiation is 1.77 and the least ion dose to completely remove carbon atoms in graphene is 21.6 ion/nm2. Afterwards, the focused ion beam over 21.6 ion/nm2 is used for the irradiation on a monolayer graphene supported by SiO2 experimentally, resulting in the nanostructures, i.e., nanodot and nanowire array on the graphene. The performances of the nanostructures are characterized by atomic force microscopy and Raman spectrum. A plasma plume shielding model is put forward to explain the nanosculpting results of graphene under different irradiation parameters. In addition, two damage mechanisms are found existing in the fabrication process of the nanostructures by using empirical MD simulations. The results can help us open the possibilities for better control of nanocarbon devices.

  2. Investigation on gallium ions impacting monolayer graphene

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Xin; Zhao, Haiyan, E-mail: hyzhao@tsinghua.edu.cn; Yan, Dong; Pei, Jiayun [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084, P. R. Chinaand Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

    2015-06-15

    In this paper, the physical phenomena of gallium (Ga{sup +}) ion impacting monolayer graphene in the nanosculpting process are investigated experimentally, and the mechanisms are explained by using Monte Carlo (MC) and molecular dynamics (MD) simulations. Firstly, the MC method is employed to clarify the phenomena happened to the monolayer graphene target under Ga{sup +} ion irradiation. It is found that substrate has strong influence on the damage mode of graphene. The mean sputtering yield of graphene under 30 keV Ga{sup +} ion irradiation is 1.77 and the least ion dose to completely remove carbon atoms in graphene is 21.6 ion/nm{sup 2}. Afterwards, the focused ion beam over 21.6 ion/nm{sup 2} is used for the irradiation on a monolayer graphene supported by SiO2 experimentally, resulting in the nanostructures, i.e., nanodot and nanowire array on the graphene. The performances of the nanostructures are characterized by atomic force microscopy and Raman spectrum. A plasma plume shielding model is put forward to explain the nanosculpting results of graphene under different irradiation parameters. In addition, two damage mechanisms are found existing in the fabrication process of the nanostructures by using empirical MD simulations. The results can help us open the possibilities for better control of nanocarbon devices.

  3. Exploring atomic defects in molybdenum disulphide monolayers

    KAUST Repository

    Hong, Jinhua

    2015-02-19

    Defects usually play an important role in tailoring various properties of two-dimensional materials. Defects in two-dimensional monolayer molybdenum disulphide may be responsible for large variation of electric and optical properties. Here we present a comprehensive joint experiment-theory investigation of point defects in monolayer molybdenum disulphide prepared by mechanical exfoliation, physical and chemical vapour deposition. Defect species are systematically identified and their concentrations determined by aberration-corrected scanning transmission electron microscopy, and also studied by ab-initio calculation. Defect density up to 3.5 × 10 13 cm \\'2 is found and the dominant category of defects changes from sulphur vacancy in mechanical exfoliation and chemical vapour deposition samples to molybdenum antisite in physical vapour deposition samples. Influence of defects on electronic structure and charge-carrier mobility are predicted by calculation and observed by electric transport measurement. In light of these results, the growth of ultra-high-quality monolayer molybdenum disulphide appears a primary task for the community pursuing high-performance electronic devices.

  4. Competition between elastic and chemical effects in the intermixing of Co and Ag on Rh(111)

    Indian Academy of Sciences (India)

    Mighfar Imam; Madhura Marathe; Shobhana Narasimhan

    2008-11-01

    We have performed ab initio density functional theory calculations to investigate the formation energy and the effects of low dimensionality and reduced coordination on the magnetic properties of pseudomorphically grown monolayers of Co-Ag surface alloys on a Rh(111) substrate. We find that if such an alloy could form, its magnetic moment would be considerably enhanced relative to that of bulk Co. However, we also find that its formation is energetically disfavoured against phase-segregated forms; this can be mainly attributed to the high `chemical’ cost of forming Ag-Co bonds. Trends in the variation of magnetic moment with alloy composition are largely consistent with the Stoner argument.

  5. In situ STM imaging and direct electrochemistry of Pyrococcus furiosus ferredoxin assembled on thiolate-modified Au(111) surfaces

    DEFF Research Database (Denmark)

    Zhang, Jingdong; Christensen, Hans Erik Mølager; Ooi, Bee Lean

    2004-01-01

    We have addressed here electron transfer (ET) of Pyrococcus furiosus ferredoxin (PfFd, 7.5 kDa) in both homogeneous solution using edge plane graphite (EPG) electrodes and in the adsorbed state by electrochemistry on surface-modified single-crystal Au(111) electrodes, This has been supported...... surface modified by the same functional group monolayer and to address diffusionless direct electrochemistry, as well as surface microstructures of the protein monolayer. PfFd molecules were found to assemble on either mercaptopropionic acid (MPA) or cysteine-modified Au(111) surfaces in stable monolayers...

  6. Study of polystyrene-poly(ethylene oxide) diblock copolymer monolayers as barriers to protein adsorption

    Science.gov (United States)

    Jogikalmath, Gangadhar

    Protein adsorption resistant surfaces find use in many biomedical applications, such as catheters, dialysis devices and biosensors that involve blood contacting surfaces. To ensure long-term functioning of a device in an environment containing protein, there is a need to produce homogeneous surfaces that are resistant to protein adsorption. A polymer brush covered surface, produced by either physical adsorption or chemical grafting of hydrophilic polymers to surfaces, is one of the approaches used in creating such surfaces. High grafting densities needed to make an effective barrier are usually not realized in chemical grafting/adsorption from solution, due to self-exclusion of surface grafted molecules. In this dissertation polymer brush surfaces formed by chemically grafted PEO molecules and transferred monolayers of PS-b-PEO diblock copolymers are investigated using atomic force microscopy (AFM), surface plasmon resonance (SPR) and surface pressure measurement techniques. An AFM adhesion mapping technique was used to evaluate the surface heterogeneity of chemically modified PEO and transferred diblock copolymer monolayer surfaces. The behavior of PS-b-PEO molecules at the air-water interface was studied using Langmuir trough. The stability of transferred diblock copolymer monolayers was investigated using AFM. Using SPR, protein adsorption to the diblock copolymer layers was investigated as a function of protein size (using HSA and ferritin) as a function of grafting density of PEO in the monolayer. It was seen that a lower density of the PS-b-PEO monolayer was sufficient to prevent ferritin adsorption (larger protein) while a higher density brush layer was required to achieve complete prevention of HSA adsorption to the surface. The effect of mobility of the polymer brush layer on protein adsorption prevention was analyzed using SPR and surface pressure measurements. It was seen that the copolymer monolayer (at the air-buffer interface) rearranged itself to

  7. Application of L-thiazolidine-4-carboxylic acid monolayer in electrochemical determination of copper(Ⅱ)

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    L-Thiazolidine-4-carboxylic acid monolayer was prepared on gold electrodes through the self-assembly approach.Such novel thioether-based monolayer could efficiently preconcentrate Cu2+,which provided a simple,stable and reproducible method for the determination of Cu2+.The modified electrodes were stable enough to be continuously used for one week(more than 30 times regeneration) with lower than 10% decrease in the response.They retained their initial activity for more than one month if used once a day.The calibration curve was linear for Cu2+ from 0.6 to 158.8 μg L?1 with a detection limit of 0.38 μg L?1.The relative standard deviation was 3.2% for a series of six successive measurements.The proposed method was applied in the determination of Cu2+ in mineral water and human hair samples.

  8. Mono-layer BC2 a high capacity anode material for Li-ion batteries

    Science.gov (United States)

    Hardikar, Rahul; Samanta, Atanu; Han, Sang Soo; Lee, Kwang-Ryeol; Singh, Abhishek

    2015-04-01

    Mono-layer of graphene with high surface area compared to the bulk graphite phase, shows less Li uptake. The Li activity or kinetics can be modified via defects and/or substitutional doping. Boron and Nitrogen are the best known dopants for carbonaceous anode materials. In particular, boron doped graphene shows higher capacity and better Li adsorption compared to Nitrogen doped graphene. Here, using first principles density functional theory calculations, we study the spectrum of boron carbide (BCx) mono-layer phases in order to estimate the maximum gravimetric capacity that can be achieved by substitutional doping in graphene. Our results show that uniformly boron doped BC2 phase shows a high capacity of? 1400 mAh/g, much higher than previously reported capacity of BC3. Supported by Korea Institute of Science and Technology.

  9. Construction of recombinant modified vaccinia virus Ankara with Ag85A and ESAT-6 gene and examination of their immunogenicity in mice%重组结核抗原痘苗病毒Ankara株的构建及其免疫原性研究

    Institute of Scientific and Technical Information of China (English)

    楼觉人; 张群; 朱琳

    2008-01-01

    目的 构建5种不同类型的表达结核杆菌特异抗原的重组痘苗病毒,并研究其特异免疫原性.方法 运用同源重组技术将含结核分泌抗原Ag85A和ESAT-6的基因片段插入痘苗病毒表达质粒p18中.重组质粒导入痘苗病毒Ankara(MVA)后构建重组痘苗病毒,经筛选和Western blot鉴定,得到5个种类的带有结核抗原基因的重组病毒.用构建的5种重组病毒免疫小鼠,MTT法检测免疫后小鼠脾淋巴细胞对特异结核抗原的增殖反应;ELISA检测小鼠脾淋巴细胞培养上清液中IFN-γ的含量;结核菌素纯蛋白衍化物(PPD)皮内试验以检测重组病毒引发的针对结核抗原的特异细胞免疫应答.结果 构建的5种蘑组病毒介导的细胞表达产物经Western blot鉴定确认相对分子质量与结核抗原一致.免疫小鼠两次后,5种重组病毒免疫组脾淋巴细胞体外与Ag85A-ESAT-6融合蛋白共培养后表现出明显的增殖活性(P<0.01),培养上清液中IFN-γ的浓度均较同组细胞经生理盐水刺激明显增高(P<0.05);与空痘苗病毒或生理盐水免疫后小鼠相比,5种重组MVA免疫组脾淋巴细胞与AgB5A.ESAT-6融合蛋白共培养后同样表现出明显的增殖活性(P<0.01),与Ag85A-ESAT-6融合蛋白共培养的细胞上清液中IFN-γ的浓度均升高(P<0.01).与空痘苗病毒或生理盐水免疫后小鼠相比,5种重组MVA免疫组小鼠对PPD都表现出显著的迟发型超敏反应应答(P<0.05).结论 成功构建了5种不同类型的表达结核杆菌抗原的重组痘苗病毒疫苗,其免疫小鼠后可激发针对结核杆菌抗原的特异性细胞免疫.%Objective To construct five types of recombinant modified vaccinia virus Ankara (MVA) carrying genes encoding antigen 85A (Ag85A), early secretory antigenic target (ESAT-6) or IL-2 and to investigate the immunogenicity of these recombinant MVA in mice. Methods The genes encoding Ag85A and ESAT-6 were amplified by PCR from Mycobacterium

  10. Tribology and stability of organic monolayers on CrN: a comparison among silane, phosphonate, alkene, and alkyne chemistries.

    Science.gov (United States)

    Pujari, Sidharam P; Li, Yan; Regeling, Remco; Zuilhof, Han

    2013-08-20

    The fabrication of chemically and mechanically stable monolayers on the surfaces of various inorganic hard materials is crucial to the development of biomedical/electronic devices. In this Article, monolayers based on the reactivity of silane, phosphonate, 1-alkene, and 1-alkyne moieties were obtained on the hydroxyl-terminated chromium nitride surface. Their chemical stability and tribology were systematically investigated. The chemical stability of the modified CrN surfaces was tested in aqueous media at 60 °C at pH 3, 7, and 11 and monitored by static water contact angle measurements, X-ray photoelectron spectroscopy (XPS), ellipsometry, and Fourier transform infrared reflection absorption spectroscopy (FT-IRRAS). The tribological properties of the resulting organic monolayers with different end groups (fluorinated or nonfluorinated) were studied using atomic force microscopy (AFM). It was found that the fluorinated monolayers exhibit a dramatic reduction of adhesion and friction force as well as excellent wear resistance compared to those of nonfluorinated coatings and bare CrN substrates. The combination of remarkable chemical stability and superior tribological properties makes these fluorinated monolayers promising candidates for the development of robust high-performance devices.

  11. Functional monolayers for direct electrical biosensing

    Science.gov (United States)

    Clare, Tami Lasseter

    Frequency-dependent electrochemical impedance spectroscopy has been used to characterize changes in electrical response that accompany specific binding of a protein to its substrate, using the biotin-avidin system as a model. This thesis work shows that avidin, at concentrations in the nanomolar range, can be detected electrically in a completely label-free manner under conditions of zero average current flow and without the use of any auxiliary redox agents. Electrical circuit modeling of the interface was used to relate the frequency-dependent electrical response to the physical picture of the interface before and after avidin binding. The interaction of proteins with semiconductors such as silicon and diamond is of great interest for applications such as electronic biosensing. Investigations into the use of covalently bound oligo(ethylene glycol), EG, monolayers on diamond and silicon to minimize nonspecific protein adsorption were conducted. Protein adsorption was monitored by fluorescence scanning as a function the length of the ethylene glycol chain (EG3 through EG6) and the terminal functional group (methyl- versus hydroxyl-terminated EG3 monolayer). More quantitative measurements were made by eluting adsorbed avidin from the surface and measuring the intensity of fluorescence in the solution. This thesis work shows that high quality EG monolayers are formed on silicon and diamond and that these EG3 monolayers are as effective as EG3 self-assembled monolayers on gold at resisting nonspecific avidin adsorption. These results show promise for use of silicon and diamond materials in many potential applications such as biosensing and medical implants. Substrate roughness is shown to play a role in nonspecific protein adsorption, where carbon-based surfaces having features less than approximately 5 nm, are highly resistant to protein adsorption. Functionalization of the surfaces with hexaethylene glycol confers additional resistance to protein adsorption. These

  12. Encyclopedia of electrochemistry. Vol. 10. Modified electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Bard, A.J. [Texas Univ., Austin, TX (United States). Dept. of Chemistry; Stratmann, M. [Max-Planck-Institut fuer Eisenforschung GmbH, Duesseldorf (Germany); Rubinstein, I. [Weizmann Institute of Science, Rehovot (Israel). Dept. of Materials and Interfaces; Fujihira, Masamichi [Tokyo Institute of Technology, Yokohama (Japan). Dept. of Biomolecular Engineering; Rusling, J.F. (eds.) [Connecticut Univ., Storrs, CT (United States). Dept. of Chemistry, U-60]|[Connecticut Univ., Storrs, CT (United States). Dept. of Pharmacology

    2007-07-01

    This volume contains the following topics: 1. Preparation of monolayer modified electrodes; 2. Layer-by-layer assemblies of thin films on electrodes; 3. Epitaxial electrochemical growth; 5. Other films; 6. Ex-situ methods; 7. In-situ methods; 8. Electron transfer; 9. Charge transport in polymer-modified electrodes; 10. Electrochemical reactions on modified electrodes; 11. Redox-active dendrimers in solution and as films on surfaces; 12. Electrochemical formation of organic thin films; 13. Electron transfer and transport in ordered enzyme layers.

  13. Improved prediction of bilayer and monolayer properties using a refined BMW-MARTINI force field.

    Science.gov (United States)

    Miguel, Virginia; Perillo, Maria A; Villarreal, Marcos A

    2016-11-01

    Coarse-grained (CG) models allow enlarging the size and time scales that are reachable by atomistic molecular dynamics simulations. A CG force field (FF) for lipids and amino acids that possesses a polarizable water model has been developed following the MARTINI parametrization strategy, the BMW-MARTINI [1]. We tested the BMW-MARTINI FF capability to describe some structural and thermodynamical properties of lipid monolayers and bilayers. We found that, since the surface tension values of oil/water interfaces calculated with the model are not correct, compression isotherms of lipid monolayers present artifacts. Also, this FF predicts DPPC and DAPC bilayers to remain in the Lα phase at temperatures as low as 283K, contrary to the expected from their experimental Tm values. Finally, simulations at constant temperature of bilayers of saturated lipids belonging to PC homologous, showed an increase in the mean molecular area (Mma) upon increasing the chain length, inversely to the experimental observation. We refined BMW-MARTINI FF by modifying as few parameters as possible in order to bring simulated and experimental measurements closer. We have also modified structural parameters of the lipid geometry that do not have direct influence in global properties of the bilayer membranes or monolayers, but serve to approach the obtained CG geometry to atomistic reference values. The refined FF is able to better reproduce phase transition temperatures and Mma for saturated PC bilayers than BMW-MARTINI and MARTINI FF. Finally, the simulated surface pressure-Mma isotherms of PC monolayers resemble the experimental ones and eliminate serious artifacts of previous models.

  14. Depth profiling of APTES self-assembled monolayers using surface-enhanced confocal Raman microspectroscopy

    Science.gov (United States)

    Sun, Yingying; Yanagisawa, Masahiro; Kunimoto, Masahiro; Nakamura, Masatoshi; Homma, Takayuki

    2017-09-01

    The internal structure of self-assembled monolayers (SAMs) such as 3-aminopropyltriethoxysilane (APTES) fabricated on a glass substrate is difficult to characterize and analyze at nanometer level. In this study, we employed surface-enhanced Raman spectroscopy (SERS) to study the internal molecular structure of APTES SAMs. The sample APTES SAMs were deposited with Ag nanoparticles to enhance the Raman signal and to obtain subtler structure information, which were supported by density functional theory calculations. In addition, in order to carry out high-resolution analysis, especially for vertical direction, a fine piezo electric positioner was used to control the depth scanning with a step of 0.1 nm. We measured and distinguished the vertical Raman intensity variations of specific groups in APTES, such as Ag/NH2, CH2, and Sisbnd O, with high resolution. The interfacial bond at the two interfaces of Ag-APTES and APTES-SiO2 was identified. Moreover, APTES molecule orientation was demonstrated to be inhomogeneous from frequency shift.

  15. Electrochemical metallization of self-assembled porphyrin monolayers.

    Science.gov (United States)

    Nann, Thomas; Kielmann, Udo; Dietrich, Christoph

    2002-04-01

    Multifunctional sensor systems are becoming increasingly important in electroanalytical chemistry. Together with ongoing miniaturization there is a need for micro- and nanopatterning tools for thin electroactive layers (e.g. self-assembling monolayers). This paper documents a method for production of a micro-array of different metal-porphyrin monolayers with different sensor properties. A new method has been developed for the selective and local metallization of bare porphyrin monolayers by cathodic pulsing and sweeping. The metal-porphyrin monolayers obtained were characterized by cyclic voltammetry. It was shown that porphyrin monolayers can be metallized with manganese, iron, cobalt, and nickel by use of the new method. It is expected that all types of metal-porphyrin monolayers can be produced in the same manner.

  16. Controlled crystallization of hydroxyapatite under hexadecylamine self-assembled monolayer

    Institute of Scientific and Technical Information of China (English)

    黄苏萍; 周科朝; 刘咏; 黄伯云

    2003-01-01

    The role of self-assembled monolayer in inducing the crystal growth was investigated by X-ray diffractions (XRD), and scanning electron microscopy (SEM). Results show that crystallization in the absence of monolayer results in a mixture of poorly crystallized calcium phosphates, including hydroxyapatite (HAP) and octacalcium phosphate (OCP), while the presence of self-assembled monolayer gives rise to oriented and well crystallized HAP crystals. Moreover, the HAP crystal grows very quickly under the self-assembled monolayer, whereas very little calcium phosphate crystals grow without the monolayer. It is rationalized that the hexadecylamine monolayer with high polarity and charged density leads to increase supersaturation and lower the interfacial energy, which attributes to the HAP crystals nucleation. On the other hand, the positive headgroups construct the ordered "recognized site" with distinct size and topology, which results in the oriented HAP crystals deposit.

  17. ELASTICITY OF MONOLAYER OF LINOLEIC ACID AND ITS POLYMER

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    The dynamic elasticity of linoleic acid monolayer on a subphase of 10-4mol/L TbCla at various surface pressure has been measured by means of dynamic oscillation method in measuring the change of surface pressure caused by periodic compressionexpansion cycles of the barrier. The elasticity of monolayer increases with increasing of surface pressure linegrly. The linoleic acid polymer monolayer has been obtained under UV-irradiation in situ when keeping a constant surface pressure. But the elasticity of the resulting polymerized monolayer is even smaller than that of its corresponding monomer monolayer. The elasticity of the polymerized linoleic acid monolayer decreases with increasing polymerization time. The explanation based on entropy has been presented.

  18. One-pot synthesis of visible-light-driven Ag/Ag3PO4 photocatalyst immobilized on exfoliated montmorillonite by clay-mediated in situ reduction

    Science.gov (United States)

    Liu, Chang; Zhang, Xiaoyuan; Wu, Jianning; Meng, Guihua; Guo, Xuhong; Liu, Zhiyong

    2016-11-01

    In order to find efficient photocatalytic materials and convenient preparation method, a well-designed Ag/Ag3PO4-OMMT (organically modified montmorillonite) plasmonic photocatalyst was synthesized via the "one-pot" process without any reducing species. Ag+ could be reduced by Si-OH moiety on the surface of OMMT. The resulting samples were thoroughly studied by using X-ray diffraction, X-ray photoelectron spectra, transmission electron microscopy, scanning electron microscope, energy-dispersive X-ray spectroscopy, UV-Vis diffuse reflectance spectra, and so on. The as-prepared Ag/Ag3PO4-OMMT photocatalyst exhibited efficient, stable photocatalytic activity and recyclability for the degradation of Rhodamine B (RhB) under visible light radiation ( λ > 420 nm). The optimum synergetic effect of Ag3PO4/OMMT was found at a weight ratio of 50 %. The degradation efficiency of RhB over Ag/Ag3PO4-OMMT (1:1) was about 92.9 %, and photocatalytic activity remained stable after three cycles. The results show that the designed photocatalyst is feasible and effective. The proposed photocatalysis mechanism is probably attributed to surface plasmon resonance of metallic Ag nanoparticles (NPs) and also attributed to negatively charged exfoliated montmorillonite. The Ag/Ag3PO4-OMMT composites showed highly visible light photocatalytic activity, which makes them promising nanomaterials for further applications in water treatment.

  19. Monolayer cultivation of osteoprogenitors shortens duration of the embryonic stem cell test while reliably predicting developmental osteotoxicity.

    Science.gov (United States)

    zur Nieden, Nicole I; Davis, Lesley A; Rancourt, Derrick E

    2010-11-09

    Osteotoxic compounds administered during pregnancy can initiate skeletal congenital anomalies in the embryo. In vitro, developmental osteotoxicity of a compound can be predicted with the embryonic stem cell test (EST), the only in vitro embryotoxicity model identified to date that entirely abrogates the use of animals. Although the previously identified endpoint osteocalcin mRNA expression robustly predicts developmental osteotoxicity, it can only be assayed after 5 weeks of in vitro culture with existing embryoid body (EB)-based differentiation protocols. Therefore, the goal of this study was to characterize novel earlier endpoints of developmental osteotoxicity for the EST. The currently used EB-based differentiation protocol was modified so that a monolayer culture of pre-differentiated cells was inoculated. The expression profile of five bone-specific mRNAs, including osteocalcin, over the course of 30 differentiation days suggested an acceleration of pre-osteoblast specification in the monolayer over the EB-based protocol. Similarly, calcification was already visible after 14 days of culture in monolayer cultures. Employing image and absorption-based techniques to measure the degree of mineralization in these cells after compound treatment, the three compounds Penicillin G, 5-fluorouracil (5-FU) and all-trans retinoic acid (RA) were then tested after 14 days in monolayer cultures and compared to embryoid body-based differentiations at day 30. By modifying the culture the three test substances were classified correctly into non- or strong osteotoxic. Moreover, we were successful in shortening the assay duration from 30 to 14 days.

  20. Application of a Newly Developed High-Sensitivity HBsAg Chemiluminescent Enzyme Immunoassay for Hepatitis B Patients with HBsAg Seroclearance

    OpenAIRE

    2013-01-01

    We modified and automated a highly sensitive chemiluminescent enzyme immunoassay (CLEIA) for surface antigen (HBsAg) detection using a combination of monoclonal antibodies, each for a specific epitope of HBsAg, and by improving an earlier conjugation technique. Of 471 hepatitis B virus (HBV) carriers seen in our hospital between 2009 and 2012, 26 were HBsAg seronegative as determined by the Abbott Architect assay. The Lumipulse HBsAg-HQ assay was used to recheck those 26 patients who demonstr...

  1. Application of a newly developed high-sensitivity HBsAg chemiluminescent enzyme immunoassay for hepatitis B patients with HBsAg seroclearance.

    Science.gov (United States)

    Shinkai, Noboru; Matsuura, Kentaro; Sugauchi, Fuminaka; Watanabe, Tsunamasa; Murakami, Shuko; Iio, Etsuko; Ogawa, Shintaro; Nojiri, Shunsuke; Joh, Takashi; Tanaka, Yasuhito

    2013-11-01

    We modified and automated a highly sensitive chemiluminescent enzyme immunoassay (CLEIA) for surface antigen (HBsAg) detection using a combination of monoclonal antibodies, each for a specific epitope of HBsAg, and by improving an earlier conjugation technique. Of 471 hepatitis B virus (HBV) carriers seen in our hospital between 2009 and 2012, 26 were HBsAg seronegative as determined by the Abbott Architect assay. The Lumipulse HBsAg-HQ assay was used to recheck those 26 patients who demonstrated seroclearance by the Abbott Architect assay. The performance of the Lumipulse HBsAg-HQ assay was compared with that of a quantitative HBsAg detection system (Abbott Architect) and the Roche Cobas TaqMan HBV DNA assay (CTM) (lower limit of detection, 2.1 log copies/ml) using blood serum samples from patients who were determined to be HBsAg seronegative by the Abbott Architect assay. Ten patients had spontaneous HBsAg loss. Of 8 patients treated with nucleotide analogues (NAs), two were HBsAg seronegative after stopping lamivudine therapy and 6 were HBsAg seronegative during entecavir therapy. Eight acute hepatitis B (AH) patients became HBsAg seronegative. Of the 26 patients, 16 were HBsAg positive by the Lumipulse HBsAg-HQ assay but negative by the Abbott Architect assay. The differences between the two assays in terms of detectable HBsAg persisted over the long term in the spontaneous loss group (median, 10 months), the NA-treated group (2.5 months), and the AH group (0.5 months). In 9 patients, the Lumipulse HBsAg-HQ assay detected HBsAg when HBV DNA was negative by the CTM assay. HBsAg was also detected by the Lumipulse HBsAg-HQ assay in 4 patients with an anti-HBs concentration of >10 mIU/ml, 3 of whom had no HBsAg escape mutations. The automatic, highly sensitive HBsAg CLEIA Lumipulse HBsAg-HQ is a convenient and precise assay for HBV monitoring.

  2. Ag对Pd/CeO2催化剂上氧迁移的促进作用%Enhanced Migration of Oxygen on Ag-Modified Pd/CeO2 Catalyst

    Institute of Scientific and Technical Information of China (English)

    曲振平; 程谟杰; 石川; 黄伟新; 包信和

    2001-01-01

    @@Active migration and spillover of surface species on catalyst surface can be cri tical effects in catalytic processes. As a typical instance, the storage and rel ease of oxygen in the Pt-modified CeO2 catalysts were proposed to play a very important role in catalytic elimination of noxious pollutants[1]. It ha s been demonstrated that the active oxygen species transfer between Pt and CeO 2 under different conditions[2,3]. Numerous investigations on the proper ty of Pd in the catalysts have been carried out recently[4]. Compared wi th Pt, Pd has a strong interaction with CeO2 support. Silver is a unique eleme nt whose oxide can decompose thermally

  3. Electrochemical detection of aqueous Ag+ based on Ag+-assisted ligation reaction

    Science.gov (United States)

    Miao, Peng; Han, Kun; Wang, Bidou; Luo, Gangyin; Wang, Peng; Chen, Mingli; Tang, Yuguo

    2015-03-01

    In this work, a novel strategy to fabricate a highly sensitive and selective biosensor for the detection of Ag+ is proposed. Two DNA probes are designed and modified on a gold electrode surface by gold-sulfur chemistry and hybridization. In the presence of Ag+, cytosine-Ag+-cytosine composite forms and facilitates the ligation event on the electrode surface, which can block the release of electrochemical signals labeled on one of the two DNA probes during denaturation process. Ag+ can be sensitively detected with the detection limit of 0.1 nM, which is much lower than the toxicity level defined by U.S. Environmental Protection Agency. This biosensor can easily distinguish Ag+ from other interfering ions and the performances in real water samples are also satisfactory. Moreover, the two DNA probes are designed to contain the recognition sequences of a nicking endonuclease, and the ligated DNA can thus be cleaved at the original site. Therefore, the electrode can be regenerated, which allows the biosensor to be reused for additional tests.

  4. Zitterbewegung in monolayer silicene in a magnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Romera, E. [Departamento de Física Atómica, Molecular y Nuclear and Instituto Carlos I de Física Teórica y Computacional, Universidad de Granada, Fuentenueva s/n, 18071 Granada (Spain); Roldán, J.B. [Departamento de Electrónica y Tecnología de Computadores and CITIC, Universidad de Granada, Fuentenueva s/n, 18071 Granada (Spain); Santos, F. de los [Departamento de Electromagnetismo y Física de la Materia, and Instituto Carlos I de Física Teórica y Computacional, Universidad de Granada, Fuentenueva s/n, 18071 Granada (Spain)

    2014-07-04

    We study the Zitterbewegung in monolayer silicene under a perpendicular magnetic field. Using an effective Hamiltonian, we have investigated the autocorrelation function and the density currents in this material. Moreover, we have analyzed other types of periodicities of the system (classical and revival times). Finally, the above results are compared with their counterparts in two other monolayer materials subject to a magnetic field: graphene and MoS{sub 2}. - Highlights: • We study Zitterbewegung in monolayer silicene in a magnetic field. • We have analyzed other types of periodicities in silicene. • The above results are compared with other monolayer materials (graphene and MoS{sub 2})

  5. Carbon phosphide monolayers with superior carrier mobility

    Science.gov (United States)

    Wang, Gaoxue; Pandey, Ravindra; Karna, Shashi P.

    2016-04-01

    Two dimensional (2D) materials with a finite band gap and high carrier mobility are sought after materials from both fundamental and technological perspectives. In this paper, we present the results based on the particle swarm optimization method and density functional theory which predict three geometrically different phases of the carbon phosphide (CP) monolayer consisting of sp2 hybridized C atoms and sp3 hybridized P atoms in hexagonal networks. Two of the phases, referred to as α-CP and β-CP with puckered or buckled surfaces are semiconducting with highly anisotropic electronic and mechanical properties. More remarkably, they have the lightest electrons and holes among the known 2D semiconductors, yielding superior carrier mobility. The γ-CP has a distorted hexagonal network and exhibits a semi-metallic behavior with Dirac cones. These theoretical findings suggest that the binary CP monolayer is a yet unexplored 2D material holding great promise for applications in high-performance electronics and optoelectronics.Two dimensional (2D) materials with a finite band gap and high carrier mobility are sought after materials from both fundamental and technological perspectives. In this paper, we present the results based on the particle swarm optimization method and density functional theory which predict three geometrically different phases of the carbon phosphide (CP) monolayer consisting of sp2 hybridized C atoms and sp3 hybridized P atoms in hexagonal networks. Two of the phases, referred to as α-CP and β-CP with puckered or buckled surfaces are semiconducting with highly anisotropic electronic and mechanical properties. More remarkably, they have the lightest electrons and holes among the known 2D semiconductors, yielding superior carrier mobility. The γ-CP has a distorted hexagonal network and exhibits a semi-metallic behavior with Dirac cones. These theoretical findings suggest that the binary CP monolayer is a yet unexplored 2D material holding great

  6. Diacetylene mixed Langmuir monolayers for interfacial polymerization.

    Science.gov (United States)

    Ariza-Carmona, Luisa; Rubia-Payá, Carlos; García-Espejo, G; Martín-Romero, María T; Giner-Casares, Juan J; Camacho, Luis

    2015-05-19

    Polydiacetylene (PDA) and its derivatives are promising materials for applications in a vast number of fields, from organic electronics to biosensing. PDA is obtained through polymerization of diacetylene (DA) monomers, typically using UV irradiation. DA polymerization is a 1-4 addition reaction with both initiation and growth steps with topochemical control, leading to the "blue" polymer form as primary reaction product in bulk and at interfaces. Herein, the diacetylene monomer 10,12-pentacosadiynoic acid (DA) and the amphiphilic cationic N,N'-dioctadecylthiapentacarbocyanine (OTCC) have been used to build a mixed Langmuir monolayer. The presence of OTCC imposes a monolayer supramolecular structure instead of the typical trilayer of pure DA. Surface pressure, Brewster angle microscopy, and UV-vis reflection spectroscopy measurements, as well as computer simulations, have been used to assess in detail the supramolecular structure of the DA:OTCC Langmuir monolayer. Our experimental results indicate that the DA and OTCC molecules are sequentially arranged, with the two OTCC alkyl chains acting as spacing diacetylene units. Despite this configuration is expected to prevent photopolymerization of DA, the polymerization takes place without phase segregation, thus exclusively leading to the red polydiacetylene form. We propose a simple model for the initial formation of the "blue" or "red" PDA forms as a function of the relative orientation of the DA units. The structural insights and the proposed model concerning the supramolecular structure of the "blue" and "red" forms of the PDA are aimed at the understanding of the relation between the molecular and macroscopical features of PDAs.

  7. Evidence for multi-polymorphic islands during epitaxial growth of ZnO on Ag(1 1 1)

    Science.gov (United States)

    Demiroglu, Ilker; Bromley, Stefan T.

    2016-06-01

    A range of models of free standing and Ag(1 1 1)-supported stoichiometric ZnO films with coverages between 2-3 monolayers are studied using density functional calculations. Following experimental observations we focus on stoichiometric hexagonal and triangular ad-layer islands grown on top of two complete ZnO monolayers. The adlayer islands display distinct edge and corner reconstructions and are found to induce a structural transition extending from the island core to the layered phase below. Based on our results we propose a general model of ad-layer triangular island structure based on seven regions exhibiting four distinct polymorphs.

  8. Heterostructured Ag3PO4/AgBr/Ag plasmonic photocatalyst with enhanced photocatalytic activity and stability under visible light

    Science.gov (United States)

    Wang, Wan-Sheng; Du, Hong; Wang, Rui-Xia; Wen, Tao; Xu, An-Wu

    2013-03-01

    A heterostructured Ag3PO4/AgBr/Ag plasmonic photocatalyst was prepared by a rational in situ ion exchange reaction between Ag3PO4 micro-cubes and Br- in aqueous solution followed by photoreduction. The photocatalytic activities of obtained photocatalysts were measured by the degradation of methyl orange (MO) and methylene blue (MB) under visible light irradiation (λ >= 400 nm). Compared to AgBr/Ag, Ag3PO4/AgBr heterocrystals and pure Ag3PO4 crystals, the heterostructured Ag3PO4/AgBr/Ag plasmonic photocatalysts exhibit much higher photocatalytic activity and stability. This enhanced photocatalytic activity suggests that the synergetic effects of the heterostructured Ag3PO4/AgBr/Ag and the strong SPR of Ag NPs on the surface result in the high efficiencies of the photocatalytic activity and the improved stability. With the assistance of Ag3PO4/AgBr/Ag heterostructures, only 8 min and 12 min are taken to completely decompose MO and MB molecules under visible-light irradiation, respectively. Furthermore, the photodegradation rate does not show an obvious decrease during ten successive cycles, indicating that our heterostructured Ag3PO4/AgBr/Ag plasmonic photocatalysts are extremely stable under visible-light irradiation.A heterostructured Ag3PO4/AgBr/Ag plasmonic photocatalyst was prepared by a rational in situ ion exchange reaction between Ag3PO4 micro-cubes and Br- in aqueous solution followed by photoreduction. The photocatalytic activities of obtained photocatalysts were measured by the degradation of methyl orange (MO) and methylene blue (MB) under visible light irradiation (λ >= 400 nm). Compared to AgBr/Ag, Ag3PO4/AgBr heterocrystals and pure Ag3PO4 crystals, the heterostructured Ag3PO4/AgBr/Ag plasmonic photocatalysts exhibit much higher photocatalytic activity and stability. This enhanced photocatalytic activity suggests that the synergetic effects of the heterostructured Ag3PO4/AgBr/Ag and the strong SPR of Ag NPs on the surface result in the high

  9. Fluidization of a horizontally driven granular monolayer.

    Science.gov (United States)

    Heckel, Michael; Sack, Achim; Kollmer, Jonathan E; Pöschel, Thorsten

    2015-06-01

    We consider the transition of a horizontally vibrated monodisperse granular monolayer between its condensed state and its three-dimensional gaseous state as a function of the vibration parameters, amplitude, and frequency as well as particle number density. The transition is characterized by an abrupt change of the dynamical state which leaves its fingerprints in several measurable quantities including dissipation rate, sound emission, and a gap size which characterizes the sloshing motion of the material. The transition and its pronounced hysteresis is explained through the energy due to the collective motion of the particles relative to the container.

  10. Processing of monolayer materials via interfacial reactions

    Energy Technology Data Exchange (ETDEWEB)

    Sutter, Peter Werner; Sutter, Eli Anguelova

    2014-05-20

    A method of forming and processing of graphene is disclosed based on exposure and selective intercalation of the partially graphene-covered metal substrate with atomic or molecular intercalation species such as oxygen (O.sub.2) and nitrogen oxide (NO.sub.2). The process of intercalation lifts the strong metal-carbon coupling and restores the characteristic Dirac behavior of isolated monolayer graphene. The interface of graphene with metals or metal-decorated substrates also provides for controlled chemical reactions based on novel functionality of the confined space between a metal surface and a graphene sheet.

  11. Template-Directed Self-Assembly of Alkanethiol Monolayers: Selective Growth on Preexisting Monolayer Edges

    NARCIS (Netherlands)

    Sharpe, Ruben B.A.; Burdinski, Dirk; Huskens, Jurriaan; Zandvliet, Harold J.W.; Reinhoudt, David N.; Poelsema, Bene

    2007-01-01

    Self-assembled monolayers were investigated for their suitability as two-dimensional scaffolds for the selective growth of alkanethiol edge structures. Heterostructures with chemical contrast could be grown, whose dimensions were governed by both the initial pattern sizes and the process time. n-Oct

  12. Ag-SiO2 Janus particles based highly active SERS macroscopic substrates

    Science.gov (United States)

    Panwar, Kamlesh; Jassal, Manjeet; Agrawal, Ashwini K.

    2017-07-01

    Macroscopic SERS (M-SERS) substrate with high activity was fabricated by attaching Ag-SiO2 Janus particles with ∼3 nm sized silver nanoparticles (AgNPs) on a cellulosic film. The synthesized Ag-SiO2 Janus particles had in-situ deposited AgNPs on one-half and amine functionalization on the other-half, which was utilized for their fixation as a monolayer on cellulosic substrate. Raman spectrum of Rhodamine B (RhB) showed an enhancement factor of ∼5 × 104 for dye tagged on both Janus particles and M-SERS. In comparison, AgNPs with almost the same diameter, even after aggregation, did not show enhancement of Raman signals. The enhancement is attributed to in-situ reduction of silver precursor on the SiO2 surface leading to deposition of AgNPs and generation of a large number of fixed hot-spots in a controlled manner. The Janus particles and M-SERS with ∼3 nm sized AgNPs can find application as both SERS active as well as catalytic material.

  13. Determination of low levels of cadmium ions by the under potential deposition on a self-assembled monolayer on gold electrode

    Energy Technology Data Exchange (ETDEWEB)

    Noyhouzer, Tomer [Institute of Chemistry, Hebrew University of Jerusalem, Jerusalem 91904 (Israel); Mandler, Daniel, E-mail: mandler@vms.huji.ac.il [Institute of Chemistry, Hebrew University of Jerusalem, Jerusalem 91904 (Israel)

    2011-01-17

    The electrochemical determination of low levels of Cd using a self-assembled monolayer (SAM) modified Au electrode is reported. Determination was based on the stripping of Cd, which was deposited by under potential deposition (UPD). A series of short alkanethiol SAMs bearing different end groups, i.e., sulfonate, carboxylate and ammonium, were examined. Lowest level of detection (ca. 50 ng L{sup -1}) was achieved with a 3-mercaptopropionic acid (MPA) monolayer using subtractive anodic square wave voltammetry (SASV). Additional surface methods, namely, reductive desorption and X-ray photoelectron spectroscopy, were applied to determine the interfacial structure of the electrodeposited Cd on the modified electrodes. We conclude that the deposited Cd forms a monoatomic layer, which bridges between the gold surface and the alkanethiol monolayer associating with both the gold and the sulfur atoms.

  14. About AgEcon Search

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>AgEcon Search is a free,open access repository of full - text scholarly literature in agricultural and applied economics,inclu-ding working papers,conference papers,and journal articles. AgEcon Search is

  15. Comparative investigation of underpotential deposition of Ag from aqueous and ionic electrolytes: An electrochemical and in situ STM study.

    Science.gov (United States)

    Borissov, D; Aravinda, C L; Freyland, W

    2005-06-16

    Underpotential deposition (UPD) of Ag on Au(111) has been studied with two different electrolytes: aqueous 0.1 M H2SO4 solution in comparison with the ionic liquid 1-butyl-3-methylimidazolium chloride BMICl + AlCl3. Of particular interest is the distinct behavior of 2D phase formation at both interfaces, which has been investigated by cyclic and linear sweep voltammetry in combination with in situ electrochemical scanning tunneling microscopy (STM). It is found that one monolayer (ML) of Ag is formed in the UPD region in both electrolytes. In aqueous solution, atomically resolved STM images at 500 mV versus Ag/Ag+ show a (3 x 3) adlayer of Ag, whereas after sweeping the potential just before the commencement of the bulk Ag deposition, a transition from expanded (3 x 3) to pseudomorphic ML of Ag on Au(111) occurs. In BMICl-AlCl3, the first UPD process of Ag exhibits two peaks at 410 and 230 mV indicating that two distinct processes on the surface take place. For the first time, STM images with atomic resolution reveal a transition from an inhomogeneous to an ordered phase with a (square root of 3 x square root of 3)R30 degrees structure and an adsorption of AlCl4- anions having a superlattice of (1.65 x square root of 3)R30 degrees preceding the deposition of Ag.

  16. Atomic ensemble and electronic effects in Ag-rich AgPd nanoalloy catalysts for oxygen reduction in alkaline media.

    Science.gov (United States)

    Slanac, Daniel A; Hardin, William G; Johnston, Keith P; Stevenson, Keith J

    2012-06-13

    The ability to design and characterize uniform, bimetallic alloy nanoparticles, where the less active metal enhances the activity of the more active metal, would be of broad interest in catalysis. Herein, we demonstrate that simultaneous reduction of Ag and Pd precursors provides uniform, Ag-rich AgPd alloy nanoparticles (~5 nm) with high activities for the oxygen reduction reaction (ORR) in alkaline media. The particles are crystalline and uniformly alloyed, as shown by X-ray diffraction and probe corrected scanning transmission electron microscopy. The ORR mass activity per total metal was 60% higher for the AgPd(2) alloy relative to pure Pd. The mass activities were 2.7 and 3.2 times higher for Ag(9)Pd (340 mA/mg(metal)) and Ag(4)Pd (598 mA/mg(metal)), respectively, than those expected for a linear combination of mass activities of Ag (60 mA/mg(Ag)) and Pd (799 mA/mg(Pd)) particles, based on rotating disk voltammetry. Moreover, these synergy factors reached 5-fold on a Pd mass basis. For silver-rich alloys (Ag(≥4)Pd), the particle surface is shown to contain single Pd atoms surrounded by Ag from cyclic voltammetry and CO stripping measurements. This morphology is favorable for the high activity through a combination of modified electronic structure, as shown by XPS, and ensemble effects, which facilitate the steps of oxygen bond breaking and desorption for the ORR. This concept of tuning the heteroatomic interactions on the surface of small nanoparticles with low concentrations of precious metals for high synergy in catalytic activity may be expected to be applicable to a wide variety of nanoalloys.

  17. OXIDATION AND CHARACTERIZATION OF ACTIVE CARBON AG-5

    Directory of Open Access Journals (Sweden)

    Tatiana Goreacioc

    2015-06-01

    Full Text Available The surface chemistry of the commercial active carbon AG-5 has been modified by oxidation with concentrated nitric acid. The structural changes caused by oxidative treatment were estimated on the basis of nitrogen adsorption-desorption isotherms and thermal analysis. Boehm titration method and infrared spectral analysis have been used in order to evaluate surface chemistry characteristics of active carbon samples. After oxidation process the amount of total acidic groups on oxidized active carbon surface (AG-5ox increases by about 6 times in comparison with unmodified sample (AG-5. The concentration of the acidic groups on the oxidized active carbon surface (AG-5ox was in the following order: strong acidic >>> weak acidic > phenolic.

  18. Antimicrobial activity of tantalum oxide coatings decorated with Ag nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Huiliang, E-mail: hlc@mail.sic.ac.cn; Meng, Fanhao; Liu, Xuanyong, E-mail: xyliu@mail.sic.ac.cn [State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China)

    2016-07-15

    Silver plasma immersion ion implantation was used to decorate silver nanoparticles (Ag NPs) on tantalum oxide (TO) coatings. The coatings acted against bacterial cells (Staphylococcus epidermidis) in the dark by disrupting their integrity. The action was independent of silver release and likely driven by the electron storage capability of the Schottky barriers established at the interfaces between Ag NPs and the TO support. Moreover, no apparent side effect on the adhesion and differentiation of rat bone mesenchymal stem cells was detected when using Ag NPs-modified TO coatings. These results demonstrate that decoration of tantalum oxide using Ag NPs could be a promising procedure for improving the antibacterial properties for orthopedic and dental implants.

  19. Direct evidence of interaction-induced Dirac cones in a monolayer silicene/Ag(111) system

    OpenAIRE

    Feng, Ya; Liu, Defa; Feng, Baojie; LIU, Xu; Zhao, Lin; Xie, Zhuojin; Liu, Yan; Liang, Aiji; Hu, Cheng; Hu, Yong; He, Shaolong; Liu, Guodong; ZHANG, JUN; Chen, Chuangtian; Xu, Zuyan

    2016-01-01

    Silicene, analogous to graphene, is a one-atom-thick two-dimensional crystal of silicon which is expected to share many of the remarkable properties of graphene. The buckled honeycomb structure of silicene, along with its enhanced spin-orbit coupling, endows silicene with considerable advantages over graphene in that the spin-split states in silicene are tunable with external fields. Although the low-energy Dirac cone states lie at the heart of all novel quantum phenomena in a pristine sheet ...

  20. Sub-monolayer growth of Ag on flat and nanorippled SiO2 surfaces

    Science.gov (United States)

    Bhatnagar, Mukul; Ranjan, Mukesh; Jolley, Kenny; Smith, Roger; Mukherjee, Subroto

    2016-05-01

    In-situ Rutherford Backscattering Spectrometry (RBS) and Molecular Dynamics (MD) simulations have been used to investigate the growth dynamics of silver on a flat and the rippled silica surface. The calculated sticking coefficient of silver over a range of incidence angles shows a similar behaviour to the experimental results for an average surface binding energy of a silver adatom of 0.2 eV. This value was used to parameterise the MD model of the cumulative deposition of silver in order to understand the growth mechanisms. Both the model and the RBS results show marginal difference between the atomic concentration of silver on the flat and the rippled silica surface, for the same growth conditions. For oblique incidence, cluster growth occurs mainly on the leading edge of the rippled structure.

  1. AGS Booster prototype magnets

    Energy Technology Data Exchange (ETDEWEB)

    Danby, G.; Jackson, J.; Lee, Y.Y.; Phillips, R.; Brodowski, J.; Jablonski, E.; Keohane, G.; McDowell, B.; Rodger, E.

    1987-03-19

    Prototype magnets have been designed and constructed for two half cells of the AGS Booster. The lattice requires 2.4m long dipoles, each curved by 10/sup 0/. The multi-use Booster injector requires several very different standard magnet cycles, capable of instantaneous interchange using computer control from dc up to 10 Hz.

  2. Toward highly sensitive surface-enhanced Raman scattering: the design of a 3D hybrid system with monolayer graphene sandwiched between silver nanohole arrays and gold nanoparticles.

    Science.gov (United States)

    Zhao, Yuan; Yang, Dong; Li, Xiyu; Liu, Yu; Hu, Xiang; Zhou, Dianfa; Lu, Yalin

    2017-01-19

    We report a novel graphene-metal hybrid system by introducing monolayer graphene between gold nanoparticles (Au NPs) and silver nanohole (Ag NH) arrays. The design incorporates three key advantages to promote the surface-enhanced Raman scattering (SERS) sensing capacity: (i) making full use of the single-atomic feature of graphene for generating uniform sub-nanometer spaces; (ii) maintaining the bottom layer of Ag nanoarrays with an ordered manner for facilitating the transfer of graphene films and assembly of the top layer of Au NPs; (iii) integrating the advantages of the strong plasmonic effect of Ag, the chemical stability of Au, as well as the mechanical flexibility and biological compatibility of graphene. In this configuration, the plasmonic properties can be fine-tuned by separately optimizing the horizontal or vertical gaps between the metal NPs. Exactly, sub-20 nm spaces between the horizontally patterned Ag tips constructed by adjacent Ag NHs, and sub-nanometer scale graphene gaps between the vertically distributed Au NP-Ag NH have been achieved. Finite element numerical simulations demonstrate that the multi-dimensional plasmonic couplings (including the Au NP-Au NP, Au NP-Ag NH and Ag NH-Ag NH couplings) promote for the hybrid platform an electric field enhancement up to 137 times. Impressively, the as-prepared 3D Au NP-graphene-Ag NH array hybrid structure manifests ultrahigh SERS sensitivity with a detection limit of 10(-13) M for R6G molecules, as well as good reproducibility and stability. This work represents a step towards high-performance SERS substrate fabrication, and opens up a new route for graphene-plasmonic hybrids in SERS applications.

  3. Core-shell Au/Ag nanoparticles embedded in silicate sol-gel network for sensor application towards hydrogen peroxide

    Indian Academy of Sciences (India)

    Shanmugam Manivannan; Ramasamy Ramaraj

    2009-09-01

    The electrocatalytic activity of core-shell Au100-Ag ( = 15, 27, 46, and 60) bimetallic nanoparticles embedded in methyl functionalized silicate MTMOS network towards the reduction of hydrogen peroxide was investigated by using cyclic voltammetry and chronoamperometric techniques. Core-shell Au/Ag bimetallic nanoparticles were characterized by absorption spectra and HRTEM. The MTMOS silicate sol-gel embedded Au73Ag27 core-shell nanoparticles modified electrode showed better synergistic electrocatalytic effect towards the reduction of hydrogen peroxide when compared to monometal MTMOS-Aunps and MTMOS-Agnps modified electrodes. These modified electrodes were studied without immobilizing any enzyme in the MTMOS sol-gel matrix. The present study highlights the influence of molar composition of Ag nanoparticles in the Au/Ag bimetallic composition towards the electrocatalytic reduction and sensing of hydrogen peroxide in comparison to monometal Au and Ag nanoparticles.

  4. Sub-monolayer film growth of a volatile lanthanide complex on metallic surfaces

    Science.gov (United States)

    Chen, Jinjie; Edelmann, Kevin; Wulfhekel, Wulf

    2015-01-01

    Summary We deposited a volatile lanthanide complex, tris(2,2,6,6-tetramethyl-3,5-heptanedionato)terbium(III), onto metal surfaces of Cu(111), Ag(111) and Au(111) in vacuum and observed well-ordered sub-monolayer films with low temperature (5 K) scanning tunneling microscopy. The films show a distorted three-fold symmetry with a commensurate structure. Scanning tunneling spectroscopy reveals molecular orbitals delocalized on the ligands of the molecule. Our results imply that this complex can be transferred onto the metal substrates without molecular decomposition or contamination of the surface. This new rare-earth-based class of molecules broadens the choice of molecular magnets to study with scanning tunneling microscopy. PMID:26733215

  5. Sub-monolayer film growth of a volatile lanthanide complex on metallic surfaces

    Directory of Open Access Journals (Sweden)

    Hironari Isshiki

    2015-12-01

    Full Text Available We deposited a volatile lanthanide complex, tris(2,2,6,6-tetramethyl-3,5-heptanedionatoterbium(III, onto metal surfaces of Cu(111, Ag(111 and Au(111 in vacuum and observed well-ordered sub-monolayer films with low temperature (5 K scanning tunneling microscopy. The films show a distorted three-fold symmetry with a commensurate structure. Scanning tunneling spectroscopy reveals molecular orbitals delocalized on the ligands of the molecule. Our results imply that this complex can be transferred onto the metal substrates without molecular decomposition or contamination of the surface. This new rare-earth-based class of molecules broadens the choice of molecular magnets to study with scanning tunneling microscopy.

  6. Trion valley coherence in monolayer semiconductors

    Science.gov (United States)

    Hao, Kai; Xu, Lixiang; Wu, Fengcheng; Nagler, Philipp; Tran, Kha; Ma, Xin; Schüller, Christian; Korn, Tobias; MacDonald, Allan H.; Moody, Galan; Li, Xiaoqin

    2017-06-01

    The emerging field of valleytronics aims to exploit the valley pseudospin of electrons residing near Bloch band extrema as an information carrier. Recent experiments demonstrating optical generation and manipulation of exciton valley coherence (the superposition of electron-hole pairs at opposite valleys) in monolayer transition metal dichalcogenides (TMDs) provide a critical step towards control of this quantum degree of freedom. The charged exciton (trion) in TMDs is an intriguing alternative to the neutral exciton for control of valley pseudospin because of its long spontaneous recombination lifetime, its robust valley polarization, and its coupling to residual electronic spin. Trion valley coherence has however been unexplored due to experimental challenges in accessing it spectroscopically. In this work, we employ ultrafast 2D coherent spectroscopy to resonantly generate and detect trion valley coherence in monolayer MoSe2 demonstrating that it persists for a few-hundred femtoseconds. We conclude that the underlying mechanisms limiting trion valley coherence are fundamentally different from those applicable to exciton valley coherence.

  7. Mediated Electron Transfer at Redox Active Monolayers

    Directory of Open Access Journals (Sweden)

    Michael E.G. Lyons

    2001-12-01

    Full Text Available A theoretical model describing the transport and kinetic processes involved in heterogeneous redox catalysis of solution phase reactants at electrode surfaces coated with redox active monolayers is presented. Although the analysis presented has quite general applicability, a specific focus of the paper is concerned with the idea that redox active monolayers can be used to model an ensemble of individual molecular nanoelectrodes. Three possible rate determining steps are considered: heterogeneous electron transfer between immobilized mediator and support electrode ; bimolecular chemical reaction between redox mediator and reactant species in the solution phase, and diffusional mass transport of reactant in solution. A general expression for the steady state reaction flux is derived which is valid for any degree of reversibility of both the heterogeneous electron transfer reaction involving immobilized mediator species and of the bimolecular cross exchange reaction between immobilized mediator and solution phase reactant. The influence of reactant transport in solution is also specifically considered. Simplified analytical expressions for the net reaction flux are derived for experimentally reasonable situations and a kinetic case diagram is constructed outlining the relationships between the various approximate solutions. The theory enables simple diagnostic plots to be constructed which can be used to analyse experimental data.

  8. Predicting Two-Dimensional Silicon Carbide Monolayers.

    Science.gov (United States)

    Shi, Zhiming; Zhang, Zhuhua; Kutana, Alex; Yakobson, Boris I

    2015-10-27

    Intrinsic semimetallicity of graphene and silicene largely limits their applications in functional devices. Mixing carbon and silicon atoms to form two-dimensional (2D) silicon carbide (SixC1-x) sheets is promising to overcome this issue. Using first-principles calculations combined with the cluster expansion method, we perform a comprehensive study on the thermodynamic stability and electronic properties of 2D SixC1-x monolayers with 0 ≤ x ≤ 1. Upon varying the silicon concentration, the 2D SixC1-x presents two distinct structural phases, a homogeneous phase with well dispersed Si (or C) atoms and an in-plane hybrid phase rich in SiC domains. While the in-plane hybrid structure shows uniform semiconducting properties with widely tunable band gap from 0 to 2.87 eV due to quantum confinement effect imposed by the SiC domains, the homogeneous structures can be semiconducting or remain semimetallic depending on a superlattice vector which dictates whether the sublattice symmetry is topologically broken. Moreover, we reveal a universal rule for describing the electronic properties of the homogeneous SixC1-x structures. These findings suggest that the 2D SixC1-x monolayers may present a new "family" of 2D materials, with a rich variety of properties for applications in electronics and optoelectronics.

  9. Fabrication and Photovoltaic Properties of Ag/Au Modified TiO2 Nanotube Arrays%银金修饰TiO2纳米管阵列光阳极的制备及其光伏性质

    Institute of Scientific and Technical Information of China (English)

    樊莉红; 陈福义; 刘婧; 张金生; 刘建

    2012-01-01

    TiO2 nanotube arrays for dye - sensitized nanocryslal solar cell ( DSSC) photoanode were fabricated by the anodization from titanium foil and modified with Ag and Au on its surface using eleclrodeposi-tion, photodeposition and vacuum sputtering, respectively in this paper. The scanning electron microscope (SEM) images and X -ray diffraction (XRD) patterns show that TiO2 nanotube arrays have regular and orderly structure and are covered by a close nanopaticle film of silver and gold. In contract to pure TiO2 nanotube arrays, the TiO2 array modified with Ag has higher short circuit current density and larger open circuit voltage, which can be enhanced 3.9 and 0.7 times larger than the former, and its electrochemical impedance is reduced significantly as observed from electrochemical impedance spectroscopy (EIS) patterns and photocurrent density - voltage ( J - V ) curves. It shows that Ag modification improves the connectivity among TiO2 nanotubes, assists electron transfer inside the TiO2 nanotubes, and excites pholoelec-tron by surface plasmon resonance,meanwhile promotes the electron - hole separation inside the TiO2 crystals in visible wavelength range through interaction with TiO2.%采用阳极氧化法,以金属钛箔为原料制备了TiO2纳米管阵结构染料敏化纳米晶太阳能电池( DSSC)光阳极,并用电沉积、光沉积和真空蒸发法对其表面分别进行金属Ag和Au修饰.对金属修饰前后的光阳极用扫描电子显微镜(SEM)和X射线衍射分析仪(XRD)表征发现:阳极氧化法制备的TiO2纳米管阵列结构规整有序;经过化学沉积后,其表面均覆盖有一层致密的金属粒子薄膜.测量光电流密度-电压(J-V)曲线和电化学阻抗谱(EIS)发现:相比纯TiO2纳米管阵列,经过Ag修饰后的TiO2阵列其短路电流密度和开路电压最大可以分别提高到前者的4.9和1.7倍,并且其电化学阻抗出现显著降低.研究表明:金属Ag修饰改善了TiO2纳米管之

  10. MoS2 monolayers on nanocavities: enhancement in light-matter interaction

    Science.gov (United States)

    Janisch, Corey; Song, Haomin; Zhou, Chanjing; Lin, Zhong; Elías, Ana Laura; Ji, Dengxin; Terrones, Mauricio; Gan, Qiaoqiang; Liu, Zhiwen

    2016-06-01

    Two-dimensional (2D) atomic crystals and van der Waals heterostructures constitute an emerging platform for developing new functional ultra-thin electronic and optoelectronic materials for novel energy-efficient devices. However, in most thin-film optical applications, there is a long-existing trade-off between the effectiveness of light-matter interactions and the thickness of semiconductor materials, especially when the materials are scaled down to atom thick dimensions. Consequently, enhancement strategies can introduce significant advances to these atomically thick materials and devices. Here we demonstrate enhanced absorption and photoluminescence generation from MoS2 monolayers coupled with a planar nanocavity. This nanocavity consists of an alumina nanolayer spacer sandwiched between monolayer MoS2 and an aluminum reflector, and can strongly enhance the light-matter interaction within the MoS2, increasing the exclusive absorption of monolayer MoS2 to nearly 70% at a wavelength of 450 nm. The nanocavity also modifies the spontaneous emission rate, providing an additional design freedom to control the interaction between light and 2D materials.

  11. Embedding Ba Monolayers and Bilayers in Boron Carbide Nanowires

    Science.gov (United States)

    Yu, Zhiyang; Luo, Jian; Shi, Baiou; Zhao, Jiong; Harmer, Martin P.; Zhu, Jing

    2015-11-01

    Aberration corrected high angle annular dark field scanning transmission electron microscopy (HAADF-STEM) was employed to study the distribution of barium atoms on the surfaces and in the interiors of boron carbide based nanowires. Barium based dopants, which were used to control the crystal growth, adsorbed to the surfaces of the boron-rich crystals in the form of nanometer-thick surficial films (a type of surface complexion). During the crystal growth, these dopant-based surface complexions became embedded inside the single crystalline segments of fivefold boron-rich nanowires collectively, where they were converted to more ordered monolayer and bilayer modified complexions. Another form of bilayer complexion stabilized at stacking faults has also been identified. Numerous previous works suggested that dopants/impurities tended to segregate at the stacking faults or twinned boundaries. In contrast, our study revealed the previously-unrecognized possibility of incorporating dopants and impurities inside an otherwise perfect crystal without the association to any twin boundary or stacking fault. Moreover, we revealed the amount of barium dopants incorporated was non-equilibrium and far beyond the bulk solubility, which might lead to unique properties.

  12. Electrodeposition of gold templated by patterned thiol monolayers

    Science.gov (United States)

    She, Zhe; Di Falco, Andrea; Hähner, Georg; Buck, Manfred

    2016-06-01

    The electrochemical deposition of Au onto Au substrates modified by self-assembled monolayers (SAMs) was studied by linear sweep voltammetry (LSV), atomic force microscopy (AFM) and scanning electron microscopy (SEM). Patterned SAMs exhibiting electrochemical contrast were prepared by two different methods. One used microcontact printing (μCP) to generate a binary SAM of ω-(4‧-methyl-biphenyl-4-yl)-propane thiol (CH3-C6H4-C6H4-(CH2)3-SH, MBP3) and octadecane thiol (CH3(CH2)17SH, ODT). Templated by the SAM, a gold microelectrode structure was electrodeposited featuring a line 15 μm wide and 3 mm long. After transfer to an epoxy substrate the structure proved to be electrically conductive across the full length. The other patterning method applied electron beam lithography (EBL) where electrochemical contrast was achieved by crosslinking molecules in a single component SAM of MBP3. An electron dose above 250 mC/cm2 results in a high deposition contrast. The choice of parameters for the deposition/lift-off process is found to be more critical for Au compared to Cu studied previously. The origin of the differences and implications for nanoscale patterning are discussed.

  13. Monte Carlo study of electron transport in monolayer silicene

    Science.gov (United States)

    Borowik, Piotr; Thobel, Jean-Luc; Adamowicz, Leszek

    2016-11-01

    Electron mobility and diffusion coefficients in monolayer silicene are calculated by Monte Carlo simulations using simplified band structure with linear energy bands. Results demonstrate reasonable agreement with the full-band Monte Carlo method in low applied electric field conditions. Negative differential resistivity is observed and an explanation of the origin of this effect is proposed. Electron mobility and diffusion coefficients are studied in low applied electric field conditions. We demonstrate that a comparison of these parameter values can provide a good check that the calculation is correct. Low-field mobility in silicene exhibits {T}-3 temperature dependence for nondegenerate electron gas conditions and {T}-1 for higher electron concentrations, when degenerate conditions are imposed. It is demonstrated that to explain the relation between mobility and temperature in nondegenerate electron gas the linearity of the band structure has to be taken into account. It is also found that electron-electron scattering only slightly modifies low-field electron mobility in degenerate electron gas conditions.

  14. Embedding Ba Monolayers and Bilayers in Boron Carbide Nanowires.

    Science.gov (United States)

    Yu, Zhiyang; Luo, Jian; Shi, Baiou; Zhao, Jiong; Harmer, Martin P; Zhu, Jing

    2015-11-26

    Aberration corrected high angle annular dark field scanning transmission electron microscopy (HAADF-STEM) was employed to study the distribution of barium atoms on the surfaces and in the interiors of boron carbide based nanowires. Barium based dopants, which were used to control the crystal growth, adsorbed to the surfaces of the boron-rich crystals in the form of nanometer-thick surficial films (a type of surface complexion). During the crystal growth, these dopant-based surface complexions became embedded inside the single crystalline segments of fivefold boron-rich nanowires collectively, where they were converted to more ordered monolayer and bilayer modified complexions. Another form of bilayer complexion stabilized at stacking faults has also been identified. Numerous previous works suggested that dopants/impurities tended to segregate at the stacking faults or twinned boundaries. In contrast, our study revealed the previously-unrecognized possibility of incorporating dopants and impurities inside an otherwise perfect crystal without the association to any twin boundary or stacking fault. Moreover, we revealed the amount of barium dopants incorporated was non-equilibrium and far beyond the bulk solubility, which might lead to unique properties.

  15. Miscibility of dl-α-tocopherol β-glucoside in DPPC monolayer at air/water and air/solid interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Neunert, G. [Department of Physics and Biophysics, Poznan University of Life Sciences, 60-637 Poznan (Poland); Makowiecki, J.; Piosik, E.; Hertmanowski, R. [Faculty of Technical Physics, Poznan University of Technology, 60-965 Poznan (Poland); Polewski, K. [Department of Physics and Biophysics, Poznan University of Life Sciences, 60-637 Poznan (Poland); Martynski, T., E-mail: tomasz.martynski@put.poznan.pl [Faculty of Technical Physics, Poznan University of Technology, 60-965 Poznan (Poland)

    2016-10-01

    The role of newly synthesized tocopherol glycosidic derivative in modifying molecular organization and phase transitions of phospholipid monolayer at the air/water interface has been investigated. Two-component Langmuir films of dl-α-tocopheryl β-D-glucopyranoside (BG) mixed with dipalmitoyl phosphatidylcholine (DPPC) in the whole range of mole fractions were formed at the water surface. An analysis of surface pressure versus mean molecular area (π-A) isotherms and Brewster angle microscope images showed that the presence of BG molecules changes the structure and packing of the DPPC monolayer in a BG concentration dependent manner. BG molecules incorporated into DPPC monolayer inhibit its liquid expanded to liquid condensed phase transition proportionally to the BG concentration. The monolayers were also transferred onto solid substrates and visualized using an atomic force microscope. The results obtained indicate almost complete miscibility of BG and DPPC in the monolayers at surface pressures present in the biological cell membrane (30-35·10{sup -3} N·m{sup -1}) for a BG mole fraction as high as 0.3. This makes the monolayer less packed and more disordered, leading to an increased permeability. The results support our previous molecular dynamics simulation data. - Highlights: • Langmuir films of α-tocopherol derivative with DPPC was studied thermodynamically. • Mixed DPPC/BG films were transferred onto mica substrates for topography imaging by using AFM. • Miscibility of BG/DPPC films at surface pressures present in membranes was observed up to MF = 0.3.

  16. Modified cyanobacteria

    Science.gov (United States)

    Vermaas, Willem F J.

    2014-06-17

    Disclosed is a modified photoautotrophic bacterium comprising genes of interest that are modified in terms of their expression and/or coding region sequence, wherein modification of the genes of interest increases production of a desired product in the bacterium relative to the amount of the desired product production in a photoautotrophic bacterium that is not modified with respect to the genes of interest.

  17. {alpha}-Man monolayer formation via Si-C bond formation and protein recognition

    Energy Technology Data Exchange (ETDEWEB)

    Funato, Koji [School of Materials Science, Japan Advanced Institute of Science and Technology, 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan); Shirahata, Naoto [National Institute for Materials Science (NIMS), 1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Miura, Yoshiko, E-mail: miuray@jaist.ac.j [School of Materials Science, Japan Advanced Institute of Science and Technology, 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan)

    2009-11-30

    An acetylenyl-terminated saccharide was synthesized and the thin layer formation on the hydrogen-terminated silicon was investigated. The acetylenyl-terminated saccharide was synthesized by the condensation reaction of hexynoic acid and p-aminophenyl saccharide. This was reacted with hydrogen-terminated silicon (Si-H) by a photochemical reaction. The resulting saccharide modified substrate was analyzed by ellipsometry and X-ray photoelectron spectroscopy, which showed the formation of a uniform monolayer. The surface's ability to recognize proteins was analyzed by fluorescent microscopy, and showed specific interactions with sugar recognition proteins.

  18. State-selective energy and angular resolved detection of neutral species ejected from keV ion bombarded C{sub 6}H{sub 6}/Ag{l_brace}1 1 1{r_brace}

    Energy Technology Data Exchange (ETDEWEB)

    Vandeweert, E.; Meserole, C.A.; Sostarecz, A.; Dou, Y.; Winograd, N. E-mail: nxw@psu.edunxw@psuvm.psu.edu; Postawa, Z

    2000-04-01

    We investigated the desorption of neutral benzene (C{sub 6}H{sub 6}) molecules and silver atoms from C{sub 6}H{sub 6}/Ag{l_brace}1 1 1{r_brace} upon bombardment by 8 keV Ar{sup +} ions. Using state-selective resonant ionization spectroscopy, substrate atoms sputtered in the ground and a high-lying metastable state, and ground-state and vibrationally excited molecules could be probed separately. The silver atom yield, kinetic energy and polar angle distributions were found to be modified upon benzene dosing. From these results, it was inferred that a large fraction of the metastable silver atoms de-excite during collisions with adsorbates. Also the ejection of benzene molecules depends strongly both on the internal energy of the molecules and the degree of coverage of the Ag surface. Up to monolayer thickness, the benzene molecules are mainly ejected during collisions with departing substrate particles. Molecules with higher internal energy leave the surface with a distribution shifted towards higher kinetic energies. At multi-layer coverages, a slow desorption mechanism becomes dominant. It is suggested that only benzene molecules vibrationally excited near the benzene-vacuum interface can survive the ejection process without de-excitation.

  19. Thermodynamic behavior of D-sphingosine/cholesterol monolayers and the topography observed by AFM

    Institute of Scientific and Technical Information of China (English)

    HAO ChangChun; SUN RunGuang; ZHANG Jing; CHANG YiGuang; NIU ChunLing

    2009-01-01

    Lipid rafts are of a dynamic microdomain structure found in recent years, enriched in sphingolipids, cholesterol and particular proteins. The change of structure and function of lipid rafts could result in many diseases. In this work, the monolayer behavior of mixed systems of D-sphingosine with choles-terol was investigated in terms of the mean surface area per molecule (Am), excess molecular area (△Aex), surface excess Gibbs energy (△Gex), interaction parameter (ω) activity coefficients (f1 and f2) as well as elasticity (Cs-1) of formed films. The deposited Langmuir-Blodgett (LB) monolayers were inves-tigated with atomic force microscopy (AFM). Thermodynamic analysis indicates △Aex and △Gex in the binary systems with negative deviations from the ideal behavior, suggesting attractive interaction be-tween molecules. The stability, elasticity and activity coefficients show a marked dependence on the mole faction of D-sphingosine. The results of observation by AFM show that the single D-sphingosine molecular film took on small granule structure. When mixing the D-sphingosine and cholesterol at dif-ferent ratios, the mixed films transform from the chains structure to larger slice and net coexisting structure with the increasing of the cholesterol content. In the end, pure cholesterol forms more ag-gregated structure. AFM experiments effectively support the above findings and interpretation.

  20. Thermodynamic behavior of D-sphingosine/cholesterol monolayers and the topography observed by AFM

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Lipid rafts are of a dynamic microdomain structure found in recent years,enriched in sphingolipids,cholesterol and particular proteins.The change of structure and function of lipid rafts could result in many diseases.In this work,the monolayer behavior of mixed systems of D-sphingosine with choles-terol was investigated in terms of the mean surface area per molecule(Am),excess molecular area(Aex),surface excess Gibbs energy(Gex),interaction parameter(ω),activity coefficients(1 and 2) as well as elasticity(Cs1) of formed films.The deposited Langmuir-Blodgett(LB) monolayers were inves-tigated with atomic force microscopy(AFM).Thermodynamic analysis indicates Aex and Gex in the binary systems with negative deviations from the ideal behavior,suggesting attractive interaction be-tween molecules.The stability,elasticity and activity coefficients show a marked dependence on the mole faction of D-sphingosine.The results of observation by AFM show that the single D-sphingosine molecular film took on small granule structure.When mixing the D-sphingosine and cholesterol at dif-ferent ratios,the mixed films transform from the chains structure to larger slice and net coexisting structure with the increasing of the cholesterol content.In the end,pure cholesterol forms more ag-gregated structure.AFM experiments effectively support the above findings and interpretation.

  1. Melting mechanism in monolayers of flexible rod-shaped molecules

    DEFF Research Database (Denmark)

    Hansen, Flemming Yssing; Taub, H.

    1992-01-01

    mechanism for melting in monolayers of flexible rod-shaped molecules. Melting requires the formation of vacancies in the monolayer by molecular motion perpendicular to the surface. This ‘‘footprint reduction’’ mechanism implies that strictly two-dimensional theories of melting are inapplicable...

  2. Modelling Organic Surfaces with Self-Assembled Monolayers

    Science.gov (United States)

    1989-05-01

    reactive organic liquids. Fluorinated thiols form monolayers that are more water and oil-repellent than Teflon. The hydrophobicity and oleophobicity of...and are both hydrophobic and oleophobic . The surface of a monolayer containing an approximately equal mixture of the two components 13 resembles a

  3. A MOLECULAR-DYNAMICS STUDY OF LECITHIN MONOLAYERS

    NARCIS (Netherlands)

    AHLSTROM, P; BERENDSEN, HJC

    1993-01-01

    Two monolayers of didecanoyllecithin at the air-water interface have been studied using molecular dynamics simulations. The model system consisted of two monolayers of 42 lecithin molecules each separated by a roughly 4 nm thick slab of SPC water. The area per lecithin molecule was 0.78 nm(2)

  4. Large work function shift of gold induced by a novel perfluorinated azobenzene-based self-assembled monolayer.

    Science.gov (United States)

    Crivillers, Núria; Osella, Silvio; Van Dyck, Colin; Lazzerini, Giovanni M; Cornil, David; Liscio, Andrea; Di Stasio, Francesco; Mian, Shabbir; Fenwick, Oliver; Reinders, Federica; Neuburger, Markus; Treossi, Emanuele; Mayor, Marcel; Palermo, Vincenzo; Cacialli, Franco; Cornil, Jérôme; Samorì, Paolo

    2013-01-18

    Tune it with light! Self-assembled monolayers on gold based on a chemisorbed novel azobenzene derivative with a perfluorinated terminal phenyl ring are prepared. The modified substrate shows a significant work function increase compared to the bare metal. The photo-conversion between trans and cis isomers chemisorbed on the surface shows great perspectives for being an accessible route to tune the gold properties by means of light.

  5. Structure and Phase Transitions of Monolayers of Intermediate-length n-alkanes on Graphite Studied by Neutron Diffraction and Molecular Dynamics Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Taub, H. [University of Missouri, Columbia; Hansen, F.Y. [Technical University of Denmark; Diama, Amand [National University of the Ivory Coast; Matthies, Blake [Goodyear Tire and Rubber Company, The; Criswell, Leah [University of Missouri, Columbia; Mo, Haiding [Advanced Optowave Corporation; Bai, M [University of Missouri, Columbia; Herwig, Kenneth W [ORNL

    2009-01-01

    We present evidence from neutron diffraction measurements and molecular dynamics (MD) simulations of three different monolayer phases of the intermediate-length alkanes tetracosane (n-C(24)H(50) denoted as C24) and dotriacontane (n-C(32)H(66) denoted as C32) adsorbed on a graphite basal-plane surface. Our measurements indicate that the two monolayer films differ principally in the transition temperatures between phases. At the lowest temperatures, both C24 and C32 form a crystalline monolayer phase with a rectangular-centered (RC) structure. The two sublattices of the RC structure each consists of parallel rows of molecules in their all-trans conformation aligned with their long axis parallel to the surface and forming so-called lamellas of width approximately equal to the all-trans length of the molecule. The RC structure is uniaxially commensurate with the graphite surface in its [110] direction such that the distance between molecular rows in a lamella is 4.26 A=sqrt[3a(g)], where a(g)=2.46 A is the lattice constant of the graphite basal plane. Molecules in adjacent rows of a lamella alternate in orientation between the carbon skeletal plane being parallel and perpendicular to the graphite surface. Upon heating, the crystalline monolayers transform to a 'smectic' phase in which the inter-row spacing within a lamella expands by approximately 10% and the molecules are predominantly oriented with the carbon skeletal plane parallel to the graphite surface. In the smectic phase, the MD simulations show evidence of broadening of the lamella boundaries as a result of molecules diffusing parallel to their long axis. At still higher temperatures, they indicate that the introduction of gauche defects into the alkane chains drives a melting transition to a monolayer fluid phase as reported previously.

  6. Structure and phase transitions of monolayers of intermediate-length n-alkanes on graphite studied by neutron diffraction and molecular dynamics simulation.

    Science.gov (United States)

    Diama, A; Matthies, B; Herwig, K W; Hansen, F Y; Criswell, L; Mo, H; Bai, M; Taub, H

    2009-08-28

    We present evidence from neutron diffraction measurements and molecular dynamics (MD) simulations of three different monolayer phases of the intermediate-length alkanes tetracosane (n-C(24)H(50) denoted as C24) and dotriacontane (n-C(32)H(66) denoted as C32) adsorbed on a graphite basal-plane surface. Our measurements indicate that the two monolayer films differ principally in the transition temperatures between phases. At the lowest temperatures, both C24 and C32 form a crystalline monolayer phase with a rectangular-centered (RC) structure. The two sublattices of the RC structure each consists of parallel rows of molecules in their all-trans conformation aligned with their long axis parallel to the surface and forming so-called lamellas of width approximately equal to the all-trans length of the molecule. The RC structure is uniaxially commensurate with the graphite surface in its [110] direction such that the distance between molecular rows in a lamella is 4.26 A=sqrt[3a(g)], where a(g)=2.46 A is the lattice constant of the graphite basal plane. Molecules in adjacent rows of a lamella alternate in orientation between the carbon skeletal plane being parallel and perpendicular to the graphite surface. Upon heating, the crystalline monolayers transform to a "smectic" phase in which the inter-row spacing within a lamella expands by approximately 10% and the molecules are predominantly oriented with the carbon skeletal plane parallel to the graphite surface. In the smectic phase, the MD simulations show evidence of broadening of the lamella boundaries as a result of molecules diffusing parallel to their long axis. At still higher temperatures, they indicate that the introduction of gauche defects into the alkane chains drives a melting transition to a monolayer fluid phase as reported previously.

  7. SELECTIVE NEURITE OUTGROWTH ON SILVER NEGATIVE ION (Ag-)-IMPLANTED POLYSTYRENE SURFACES

    Institute of Scientific and Technical Information of China (English)

    Hiroko Sato; Hiroshi Tsuji; Hitoshi Sasaki; Shinichi Ikemura; Yasuhito Gotoh; Junzo Ishikawa; Sei-ichi Nishimoto

    2004-01-01

    The negative ion implantation technique was applied to modify polymer surfaces of culture dishes for neuronal cells, PC12h. The silver negative ion (Ag-)-implantation was carried out at an ion energy of 20 keV and a dose of 3 ×1015 ions/cm2 with non-treated polystyrene (NTPS), tissue culture polystyrene (TCPS), and collagen-coated TCPS-Iwaki (CCPS). Ag--implanted surfaces of Ag/NTPS, Ag/TCPS, and Ag/CCPS were studied with respect to contact angle and/or chemical composition. The numerical values of contact angles on Ag/NTPS and Ag/TCPS were similar within experimental error, indicating the resemblance in their hydrophobicity and hydrophilicity. The PC12h cells, however, were attached only to the Ag--implanted region of NTPS, but not to the non-implanted NTPS region. Moreover, the neurite outgrowth was also observed to extend specifically along the Ag--implanted region of NTPS but not on the non-implanted NTPS region,although neurites extended towards all directions on collagen-coated TCPS as a control surface. There was no remarkable difference in neurite outgrowth among Ag--implanted regions of TCPS and CCPS. Thus Ag/NTPS region was affirmed to promote highly selective attachment, growth, and differentiation of PC 12h cells, although its mechanism is still unknown.

  8. (RE)BaCuO/Ag Composites: The Role of Silver in Bulk Materials and Joints

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    We have investigated the phase equilibria in (RE)BaCuO/Ag systems, the influence of Ag on the processing of (RE)BaCuO/Ag composites and the resulting properties. YBaCuO/Ag composites have been grown by the modified melt crystallization process with YBa2Cu3O7, Y2O3, Pt and Ag2O in the precursor. The improved strength of the YBaCuO/Ag composites compared with the conventional YBaCuO bulk material permitted us to magnetize these materials to achieve trapped fields up to 16 T (at 24 K) in the gap of a mini-magnet. The investigation of the microstructure revealed a remarkable increase of the spacing between micro-cracks especially of those perpendicular to a/b-planes when 12 wt% Ag was added. In the case of SmBaCuO/Ag composites, Ag has a strong influence on processing and causes interactions between RE123 seeds and the sample. We show the growth of single-grain SmBaCuO/Ag composites in air and discuss the influence of post-annealing on increasing Tc and Jc. Furthermore, YBaCuO/Ag composites have been shown to be appropriate materials used as a solder to join large single grains to large arrays or to "repair" grain boundaries in arrays grown by a multiseeding technique.

  9. Enhancement of stability of N-doped TiO{sub 2} photocatalysts with Ag loading

    Energy Technology Data Exchange (ETDEWEB)

    Gao Yuanpeng [Department of Physics and Key Laboratory of Artificial Micro- and Nano-structures of Ministry of Education, Wuhan University, Wuhan 430072 (China); Fang Pengfei, E-mail: fangpf@whu.edu.cn [Department of Physics and Key Laboratory of Artificial Micro- and Nano-structures of Ministry of Education, Wuhan University, Wuhan 430072 (China); Chen Feitai; Liu Yang; Liu Zhi; Wang Dahai [Department of Physics and Key Laboratory of Artificial Micro- and Nano-structures of Ministry of Education, Wuhan University, Wuhan 430072 (China); Dai Yiqun, E-mail: dai@whu.edu.cn [Department of Physics and Key Laboratory of Artificial Micro- and Nano-structures of Ministry of Education, Wuhan University, Wuhan 430072 (China)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer An effective and alternative approach is proposed to stabilize the N dopants for TiO{sub 2}. Black-Right-Pointing-Pointer Introduction of Ag restrains the escape of N dopants during the hydrothermal process. Black-Right-Pointing-Pointer The escape rate of N dopants decreased with the increase of Ag loading amount. Black-Right-Pointing-Pointer Ag nanoparticles with appropriate dosage acted as electron traps. Black-Right-Pointing-Pointer The photocatalytic activity can be adjusted by altering the Ag content. - Abstract: Various contents of Ag nanoparticles were successfully introduced into the N-doped TiO{sub 2} photocatalysts via a hydrothermal procedure in the silver-ammonia solutions with different Ag concentrations. Effects of Ag loading on the structure and properties of N-doped TiO{sub 2} photocatalysts were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy, fluorescence spectroscopy (FL), UV-vis spectroscopy, X-ray photoelectron spectroscopy (XPS), and N{sub 2} physical adsorption analysis. The relationship between the stability of N dopants in TiO{sub 2} lattice and the Ag loading content was investigated for the first time. The results confirm that Ag nanoparticles loading on TiO{sub 2} surfaces significantly restrain the escape of the N dopants from the oxide during the hydrothermal process, and the escape rate of N dopants decreased gradually with the increase of Ag loading amount. The dependence of photocatalytic activity on Ag content was also investigated through degradation of rhodamine B (RhB) under visible light irradiation. It was found that the photocatalytic activity increases gradually with increasing Ag content first, and then decreases after exceeding the optimal Ag content. Therefore, the photocatalytic activity of Ag/N co-modified TiO{sub 2} photocatalysts can be adjusted by the Ag content.

  10. Monolayer-by-monolayer stacked pyramid-like MoS2 nanodots on monolayered MoS2 flakes with enhanced photoluminescence.

    Science.gov (United States)

    Yuan, Cailei; Cao, Yingjie; Luo, Xingfang; Yu, Ting; Huang, Zhenping; Xu, Bo; Yang, Yong; Li, Qinliang; Gu, Gang; Lei, Wen

    2015-11-07

    The precise control of the morphology and crystal shape of MoS2 nanostructures is of particular importance for their application in nanoelectronic and optoelectronic devices. Here, we describe a single step route for the synthesis of monolayer-by-monolayer stacked pyramid-like MoS2 nanodots on monolayered MoS2 flakes using a chemical vapor deposition method. First-principles calculations demonstrated that the bandgap of the pyramid-like MoS2 nanodot is a direct bandgap. Enhanced local photoluminescence emission was observed in the pyramid-like MoS2 nanodot, in comparison with monolayered MoS2 flakes. The findings presented here provide new opportunities to tailor the physical properties of MoS2via morphology-controlled synthesis.

  11. A pentacene monolayer trapped between graphene and a substrate

    Science.gov (United States)

    Zhang, Qicheng; Peng, Boyu; Chan, Paddy Kwok Leung; Luo, Zhengtang

    2015-08-01

    A self-assembled pentacene monolayer can be fabricated between the solid-solid interface of few-layered graphene (FLG) and the mica substrate, through a diffusion-spreading method. By utilizing a transfer method that allows us to sandwich pentacene between graphene and mica, followed by controlled annealing, we enabled the diffused pentacene to be trapped in the interfaces and led to the formation of a stable monolayer. We found that the formation of a monolayer is kinetically favored by using a 2D Ising lattice gas model for pentacene trapped between the graphene-substrate interfaces. This kinetic Monte Carlo simulation results indicate that, due to the graphene substrate enclosure, the spreading of the first layer proceeds faster than the second layer, as the kinetics favors the filling of voids by molecules from the second layer. This graphene assisted monolayer assembly method provides a new avenue for the fabrication of two-dimensional monolayer structures.A self-assembled pentacene monolayer can be fabricated between the solid-solid interface of few-layered graphene (FLG) and the mica substrate, through a diffusion-spreading method. By utilizing a transfer method that allows us to sandwich pentacene between graphene and mica, followed by controlled annealing, we enabled the diffused pentacene to be trapped in the interfaces and led to the formation of a stable monolayer. We found that the formation of a monolayer is kinetically favored by using a 2D Ising lattice gas model for pentacene trapped between the graphene-substrate interfaces. This kinetic Monte Carlo simulation results indicate that, due to the graphene substrate enclosure, the spreading of the first layer proceeds faster than the second layer, as the kinetics favors the filling of voids by molecules from the second layer. This graphene assisted monolayer assembly method provides a new avenue for the fabrication of two-dimensional monolayer structures. Electronic supplementary information (ESI

  12. Hexadecadienyl Monolayers on Hydrogen-Terminated Si(III): Faster Monolayer Formation and Improved Surface Coverage Using the Enyne Moiety

    NARCIS (Netherlands)

    Rijksen, B.M.G.; Pujari, S.P.; Scheres, L.M.W.; Rijn, van C.J.M.; Baio, J.E.; Weidner, T.; Zuilhof, H.

    2012-01-01

    To further improve the coverage of organic monolayers on hydrogen-terminated silicon (H–Si) surfaces with respect to the hitherto best agents (1-alkynes), it was hypothesized that enynes (H–C=C–HC-CH–R) would be even better reagents for dense monolayer formation. To investigate whether the increased

  13. Study on Ag mesh/conductive oxide hybrid transparent electrode for film heaters

    Science.gov (United States)

    Kwon, Namyong; Kim, Kyohyeok; Heo, Jinhee; Yi, Insook; Chung, Ilsub

    2014-07-01

    Ag mesh-indium tin oxide (ITO) hybrid transparent conductive films were fabricated and evaluated for use in film heaters. PS monolayer templates were prepared using highly mono-dispersed PS spheres (11.2 μm) obtained by a filtering process with micro-sieves. At first, three Ag meshes with different sheet resistances (20, 100, and 300 Ω sq-1) and transmittances (70, 73, and 76%) were evaluated for film heaters in terms of voltage and long-term stability. Subsequently, in an effort to obtain better transmittance, Ag mesh-ITO hybrid heaters were fabricated utilizing finite ITO depositions. At the optimised ITO thickness (15 nm), the sheet resistance and the transmittance were 300 Ω sq-1 and 88%, respectively, which indicates that this material is a good potential candidate for an efficient defroster in vehicles.

  14. AGS experiments -- 1991, 1992, 1993. Tenth edition

    Energy Technology Data Exchange (ETDEWEB)

    Depken, J.C.

    1994-04-01

    This report contains: (1) FY 1993 AGS schedule as run; (2) FY 1994--95 AGS schedule; (3) AGS experiments {ge} FY 1993 (as of 30 March 1994); (4) AGS beams 1993; (5) AGS experimental area FY 1991 physics program; (6) AGS experimental area FY 1992 physics program; (7) AGS experimental area FY 1993 physics program; (8) AGS experimental area FY 1994 physics program (planned); (9) a listing of experiments by number; (10) two-page summaries of each experiment; (11) listing of publications of AGS experiments; and (12) listing of AGS experiments.

  15. AGS experiments -- 1995, 1996 and 1997

    Energy Technology Data Exchange (ETDEWEB)

    Depken, J.C.; Presti, P.L.

    1997-12-01

    This report contains (1) FY 1995 AGS schedule as run; (2) FY 1996 AGS schedule as run; (3) FY 1997 AGS schedule as run; (4) FY 1998--1999 AGS schedule (proposed); (5) AGS beams 1997; (6) AGS experimental area FY 1995 physics program; (7) AGS experimental area FY 1996 physics program; (8) AGS experimental area FY 1997 physics program; (9) AGS experimental area FY 1998--1999 physics program (proposed); (10) a listing of experiments by number; (11) two-page summaries of each experiment, in order by number; and (12) listing of publications of AGS experiments.

  16. Emprego de monocamadas auto-organizadas no desenvolvimento de sensores eletroquímicos Self-assembled monolayers applications for the development of electrochemical sensors

    Directory of Open Access Journals (Sweden)

    Renato S. Freire

    2003-05-01

    Full Text Available Self-assembled monolayers (SAMs modified electrodes exhibit unique behavior that can greatly benefit electrochemical sensing. This brief review highlights the applications of SAM modified electrodes in electroanalytical chemistry. After a general introduction, which includes the approaches for SAM development, different electrochemical systems for detecting inorganic and organic species are described and discussed. Special attention to the coupling of biological sensing element to the SAM is given, which can selectively recognize the analyte. Future prospects are also evaluated.

  17. Defect-Tolerant Monolayer Transition Metal Dichalcogenides

    DEFF Research Database (Denmark)

    Pandey, Mohnish; Rasmussen, Filip Anselm; Kuhar, Korina;

    2016-01-01

    -principles investigation of defect tolerance in 29 monolayer transition metal dichalcogenides (TMDs) of interest for nanoscale optoelectronics. We find that the TMDs based on group VI and X metals form deep gap states upon creation of a chalcogen (S, Se, Te) vacancy, while the TMDs based on group IV metals form only...... shallow defect levels and are thus predicted to be defect-tolerant. Interestingly, all the defect sensitive TMDs have valence and conduction bands with a very similar orbital composition. This indicates a bonding/antibonding nature of the gap, which in turn suggests that dangling bonds will fall inside...... the gap. These ideas are made quantitative by introducing a descriptor that measures the degree of similarity of the conduction and valence band manifolds. Finally, the study is generalized to nonpolar nanoribbons of the TMDs where we find that only the defect sensitive materials form edge states within...

  18. Vector assembly of colloids on monolayer substrates

    Science.gov (United States)

    Jiang, Lingxiang; Yang, Shenyu; Tsang, Boyce; Tu, Mei; Granick, Steve

    2017-06-01

    The key to spontaneous and directed assembly is to encode the desired assembly information to building blocks in a programmable and efficient way. In computer graphics, raster graphics encodes images on a single-pixel level, conferring fine details at the expense of large file sizes, whereas vector graphics encrypts shape information into vectors that allow small file sizes and operational transformations. Here, we adapt this raster/vector concept to a 2D colloidal system and realize `vector assembly' by manipulating particles on a colloidal monolayer substrate with optical tweezers. In contrast to raster assembly that assigns optical tweezers to each particle, vector assembly requires a minimal number of optical tweezers that allow operations like chain elongation and shortening. This vector approach enables simple uniform particles to form a vast collection of colloidal arenes and colloidenes, the spontaneous dissociation of which is achieved with precision and stage-by-stage complexity by simply removing the optical tweezers.

  19. Monolayer semiconductor nanocavity lasers with ultralow thresholds

    Science.gov (United States)

    Wu, Sanfeng; Buckley, Sonia; Schaibley, John R.; Feng, Liefeng; Yan, Jiaqiang; Mandrus, David G.; Hatami, Fariba; Yao, Wang; Vučković, Jelena; Majumdar, Arka; Xu, Xiaodong

    2015-04-01

    Engineering the electromagnetic environment of a nanometre-scale light emitter by use of a photonic cavity can significantly enhance its spontaneous emission rate, through cavity quantum electrodynamics in the Purcell regime. This effect can greatly reduce the lasing threshold of the emitter, providing a low-threshold laser system with small footprint, low power consumption and ultrafast modulation. An ultralow-threshold nanoscale laser has been successfully developed by embedding quantum dots into a photonic crystal cavity (PCC). However, several challenges impede the practical application of this architecture, including the random positions and compositional fluctuations of the dots, extreme difficulty in current injection, and lack of compatibility with electronic circuits. Here we report a new lasing strategy: an atomically thin crystalline semiconductor--that is, a tungsten diselenide monolayer--is non-destructively and deterministically introduced as a gain medium at the surface of a pre-fabricated PCC. A continuous-wave nanolaser operating in the visible regime is thereby achieved with an optical pumping threshold as low as 27 nanowatts at 130 kelvin, similar to the value achieved in quantum-dot PCC lasers. The key to the lasing action lies in the monolayer nature of the gain medium, which confines direct-gap excitons to within one nanometre of the PCC surface. The surface-gain geometry gives unprecedented accessibility and hence the ability to tailor gain properties via external controls such as electrostatic gating and current injection, enabling electrically pumped operation. Our scheme is scalable and compatible with integrated photonics for on-chip optical communication technologies.

  20. Acid monolayer functionalized iron oxide nanoparticle catalysts

    Science.gov (United States)

    Ikenberry, Myles

    Superparamagnetic iron oxide nanoparticle functionalization is an area of intensely active research, with applications across disciplines such as biomedical science and heterogeneous catalysis. This work demonstrates the functionalization of iron oxide nanoparticles with a quasi-monolayer of 11-sulfoundecanoic acid, 10-phosphono-1-decanesulfonic acid, and 11-aminoundecanoic acid. The carboxylic and phosphonic moieties form bonds to the iron oxide particle core, while the sulfonic acid groups face outward where they are available for catalysis. The particles were characterized by thermogravimetric analysis (TGA), transmission electron microscopy (TEM), potentiometric titration, diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), inductively coupled plasma optical emission spectrometry (ICP-OES), X-ray photoelectron spectrometry (XPS), and dynamic light scattering (DLS). The sulfonic acid functionalized particles were used to catalyze the hydrolysis of sucrose at 80° and starch at 130°, showing a higher activity per acid site than the traditional solid acid catalyst Amberlyst-15, and comparing well against results reported in the literature for sulfonic acid functionalized mesoporous silicas. In sucrose catalysis reactions, the phosphonic-sulfonic nanoparticles (PSNPs) were seen to be incompletely recovered by an external magnetic field, while the carboxylic-sulfonic nanoparticles (CSNPs) showed a trend of increasing activity over the first four recycle runs. Between the two sulfonic ligands, the phosphonates produced a more tightly packed monolayer, which corresponded to a higher sulfonic acid loading, lower agglomeration, lower recoverability through application of an external magnetic field, and higher activity per acid site for the hydrolysis of starch. Functionalizations with 11-aminoundecanoic acid resulted in some amine groups binding to the surfaces of iron oxide nanoparticles. This amine binding is commonly ignored in iron oxide

  1. Adsorption and decomposition of nickelocene on Ag(1 0 0): a high-resolution electron energy loss spectroscopy and temperature programmed desorption study

    Science.gov (United States)

    Pugmire, D. L.; Woodbridge, C. M.; Boag, N. M.; Langell, M. A.

    2001-02-01

    Nickelocene adsorption and decomposition on the Ag(1 0 0) surface were studied with temperature programmed desorption and high resolution electron energy loss spectroscopy. At monolayer coverages on the relatively inert Ag(1 0 0) surface at 175 K, nickelocene physisorbs molecularly, with its molecular axis perpendicular to the surface plane. Nickelocene begins decomposing to adsorbed cyclopentadienyl and nickel at 225 K. Molecular desorption is only observed from multilayer material, at 210 K, or from the first monolayer if adjacent surface sites for decomposition are not available. The cyclopentadienyl decomposes through disproportionation to cyclopentadiene, which desorbs, and adsorbed nickel and carbon fragments on the Ag(1 0 0) surface with a maximum at 525 K.

  2. Self-assembled alkanethiol monolayers on gold surfaces: resolving the complex structure at the interface by STM.

    Science.gov (United States)

    Guo, Quanmin; Li, Fangsen

    2014-09-28

    The surface properties of metals and metal oxides can be modified by adding a single layer of organic molecules. A most popular route for depositing such a molecular layer is via the formation of self-assembled monolayers (SAMs). The molecules that form SAMs have a functionality which binds to the surface and the adsorption is self-regulated to terminate at exactly one single molecular layer. The very first example, which has become the most widely studied system, of SAMs on metal surfaces consists of chemisorbed alkylthiolate on gold. Despite the simplicity in the preparation of alkanethiol SAMs and the seemingly straightforward structure of such SAMs, the detailed bonding between the sulfur head group and gold is still subject to debate. Experimental and theoretical effort in the last six years has led to a much improved understanding of this classical system of SAMs. In this review, we will highlight the most recent progress in the study of the interfacial structure of alkanethiol SAMs on gold. We focus on the important phenomenon of phase transition that occurs from n-propanethiol to n-butanethiol, and propose a unified structural model to explain how the (3 × 4) phase for short chain alkanethiol monolayers (methyl-, ethyl- and propylthiolate monolayers) changes into the (3 × 2√3)-rect./c(4 × 2) phase for long chain molecular monolayers.

  3. Controlled fabrication of hexagonally close-packed Langmuir-Blodgett silica particulate monolayers from binary surfactant and solvent systems.

    Science.gov (United States)

    Guo, Yudi; Tang, Dongyan; Du, Yunchen; Liu, Binbin

    2013-03-05

    We describe a controllable method to fabricate hexagonally close-packed Langmuir-Blodgett (LB) monolayers with stearic acid (SA) as co-surfactant and methanol as co-solvent. The optimal SA concentrations and volume ratios of chloroform to methanol are 0.8 mg/mL and 3:1 for particles of 140 nm, 0.50 mg/mL and 4:1 for particles of 300 nm, and 0.05 mg/mL and 5:1 for particles of 550 nm, respectively. Additionally, SEM detections of the monolayers transferred at different surface pressures indicate that the monolayers deposited from the binary systems are more compressible. The experimental results indicate that the interparticle repulsions and particle-water interactions can be enhanced without decreasing the particle hydrophobicity by adding SA and methanol; thus, particulate monolayers with large hexagonally close-packed domains composed of small silica particles can be successfully fabricated using LB technique. We propose that the enhanced interparticle repulsion is attributed to the Columbic repulsion resulting from the attachment of SA molecules to the CTAB modified particles around the three phase contact line.

  4. Ag修饰的Fe3 O4/TiO2复合磁性纳米纤维的制备及光催化性能%Preparation and Photocatalytic Efficiency of Fe3 O4/TiO2 Nanocomposite Fibers Modified with Ag Nanoparticles

    Institute of Scientific and Technical Information of China (English)

    达胡白乙拉; 王晓晖; 李晓天

    2014-01-01

    Fe3 O4/TiO2 nanofibers were prepared via electrospinning technique. Then, the samples were modified with Ag nanoparticles by hydrothermal method to obtain the composite fibers with strong magnetism and excellent photocatalytic efficiency. XRD, SEM, TEM and UV-Vis adsorption spectra were used to charac-terize and analyze the structure and morphology. The photocatalytic efficiency was tested under ultraviolet light irradiation using Rh B degradation as the model reaction. The results showed that TiO2 in all samples were anatases and Ag nanoparticles were scattered on the magnetic TiO2 fiber surface averagely. The UV-Vis spectra showed that TiO2 photoadsoption ability enhanced and the adsorption range were shifted to the visible light region. After modification with Ag nanoparticles, the photocatalytic efficiency of Rh B degradation rate can reach 99. 5% under 40 min UV light irradiation. The new material with strong magnetism can be separated easily and cyclically used by adding the magnetic field.%通过静电纺丝法制备了含有Fe3 O4纳米粒子的TiO2纳米纤维,采用水热法对该纤维表面进行纳米Ag修饰,制备出具有较强磁性和较好光催化性能的复合纤维.采用 X 射线衍射( XRD )、扫描电子显微镜( SEM)、透射电子显微镜( TEM)和紫外-可见光谱( UV-Vis)等对样品的结构和形貌进行表征,并以罗丹明B ( Rh B)水溶液降解为模型反应,考察样品在紫外光照射下的光催化性能.结果表明,所制备的TiO2为锐钛矿结构, Fe3 O4纳米粒子均匀分布在TiO2纤维中, Ag纳米颗粒比较均匀地分散在磁性TiO2纤维表面.经过纳米Ag修饰后,材料的光吸收能力大为增强,吸收带红移并扩展到可见光区.在紫外光照射40 min后,合成样品对Rh B的降解率达到99.5%.此外, Fe3 O4纳米粒子的存在使该材料具有较强的磁性,可通过外加磁场将其分离回收.

  5. Adhesive and conformational behaviour of mycolic acid monolayers.

    Science.gov (United States)

    Zhang, Zhenyu; Pen, Yu; Edyvean, Robert G; Banwart, Steven A; Dalgliesh, Robert M; Geoghegan, Mark

    2010-09-01

    We have studied the pH-dependent interaction between mycolic acid (MA) monolayers and hydrophobic and hydrophilic surfaces using molecular (colloidal probe) force spectroscopy. In both cases, hydrophobic and hydrophilic monolayers (prepared by Langmuir-Blodgett and Langmuir-Schaefer deposition on silicon or hydrophobized silicon substrates, respectively) were studied. The force spectroscopy data, fitted with classical DLVO (Derjaguin, Landau, Verwey, and Overbeek) theory to examine the contribution of electrostatic and van der Waals forces, revealed that electrostatic forces are the dominant contribution to the repulsive force between the approaching colloidal probe and MA monolayers. The good agreement between data and the DLVO model suggest that beyond a few nm away from the surface, hydrophobic, hydration, and specific chemical bonding are unlikely to contribute to any significant extent to the interaction energy between the probe and the surface. The pH-dependent conformation of MA molecules in the monolayer at the solid-liquid interface was studied by ellipsometry, neutron reflectometry, and with a quartz crystal microbalance. Monolayers prepared by the Langmuir-Blodgett method demonstrated a distinct pH-responsive behaviour, while monolayers prepared by the Langmuir-Schaefer method were less sensitive to pH variation. It was found that the attachment of water molecules plays a vital role in determining the conformation of the MA monolayers.

  6. The Modeling of Pulmonary Particulate Matter Transport Using Langmuir Monolayers

    Science.gov (United States)

    Eaton, Jeremy M.

    The effects of a barrier in proximity to the air-water interface on the dynamics of a Langmuir monolayer system are observed. A monolayer of Survanta, bovine lung surfactant, is deposited onto the interface of an aqueous buffer solution. Polystyrene particles one micron in diameter and tagged with fluorescent carboxylate groups are distributed evenly throughout the monolayer surface. The bead-monolayer system is compressed and expanded to induce folding. A polydimethylsiloxane (PDMS) substrate is placed below the monolayer in the buffer solution to study interactions between the folding monolayer and a barrier. The presence of the substrate is shown to shift surface pressure-area isotherms toward regions of lower area by an average of 8.9 mN/m. The surface of the PDMS substrate can be imaged using fluorescence microscopy to detect the presence of particles or surfactant that may have been transported there from the air-water interface during folding. Images show the transferral of particles and monolayer together suggesting the pinch-off of a fold or the direct interaction of a fold with the barrier.

  7. Surface-enhanced infrared absorption spectroscopy (SEIRAS) to probe monolayers of membrane proteins.

    Science.gov (United States)

    Ataka, Kenichi; Stripp, Sven Timo; Heberle, Joachim

    2013-10-01

    Surface-enhanced infrared absorption spectroscopy (SEIRAS) represents a variation of conventional infrared spectroscopy and exploits the signal enhancement exerted by the plasmon resonance of nano-structured metal thin films. The surface enhancement decays in about 10nm with the distance from the surface and is, thus, perfectly suited to selectively probe monolayers of biomembranes. Peculiar to membrane proteins is their vectorial functionality, the probing of which requires proper orientation within the membrane. To this end, the metal surface used in SEIRAS is chemically modified to generate an oriented membrane protein film. Monolayers of uniformly oriented membrane proteins are formed by tethering His-tagged proteins to a nickel nitrilo-triacetic acid (Ni-NTA) modified gold surface and SEIRAS commands molecular sensitivity to probe each step of surface modification. The solid surface used as plasmonic substrate for SEIRAS, can also be employed as an electrode to investigate systems where electron transfer reactions are relevant, like e.g. cytochrome c oxidase or plant-type photosystems. Furthermore, the interaction of these membrane proteins with water-soluble proteins, like cytochrome c or hydrogenase, is studied on the molecular level by SEIRAS. The impact of the membrane potential on protein functionality is verified by monitoring light-dark difference spectra of a monolayer of sensory rhodopsin (SRII) at different applied potentials. It is demonstrated that the interpretations of all of these experiments critically depend on the orientation of the solid-supported membrane protein. Finally, future directions of SEIRAS including cellular systems are discussed. This article is part of a Special Issue entitled: FTIR in membrane proteins and peptide studies.

  8. Ag transport in CrN-Ag nanocomposite coatings

    Energy Technology Data Exchange (ETDEWEB)

    Mulligan, C.P. [Department of Materials Science and Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); U.S. Army Armament Research Development and Engineering Center, Benet Laboratories, Watervliet, NY 12189 (United States); Papi, P.A. [Department of Materials Science and Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Gall, D., E-mail: galld@rpi.edu [Department of Materials Science and Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States)

    2012-09-01

    2-{mu}m-thick CrN-Ag composite coatings containing 22 at.% Ag were deposited on Si(001) by reactive co-sputtering at T{sub s} = 300, 400, and 500 Degree-Sign C. Subsequent vacuum annealing at T{sub a} = 425, 525, and 625 Degree-Sign C causes Ag transport to the surface. Auger electron spectroscopy and plan-view microscopy are used to quantify the Ag transport to the surface, which increases strongly with increasing {Delta}T = T{sub a} - T{sub s}. Compositional depth profiles and cross-sectional microscopy show that annealing causes a negligible Ag gradient through the composite layer, suggesting that the Ag transport is detachment-limited as opposed to diffusion-limited. Statistical analyses of Ag aggregate size-distributions within the matrix show that large aggregates ({>=} 50 nm) are unaffected by annealing, while the Ag in a large fraction of small aggregates (< 50 nm) moves to the surface, leaving behind 10-50 nm wide voids in the annealed composite. This indicates that the Ag from the smaller grains, with a higher chemical potential and thus a higher detachment rate, is transferred to the large grains on the surface which are 200-1000 nm wide. - Highlights: Black-Right-Pointing-Pointer CrN-Ag coatings were deposited at T{sub s} = 300-500 Degree-Sign C and annealed at T{sub a} = 425-625 Degree-Sign C. Black-Right-Pointing-Pointer Ag diffuses from aggregates in the coating to the surface, if T{sub a} > T{sub s}. Black-Right-Pointing-Pointer During annealing, aggregates < 50 nm become voids, those > 50 nm are unaffected. Black-Right-Pointing-Pointer The Ag transport is detachment rather than diffusion limited.

  9. Size-dependent filtration of nanoparticles on porous films composed by polystyrene microsphere monolayers and applications in site-selective deposition of nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Ruan, Weidong [Jilin University, State Key Laboratory of Supramolecular Structure and Materials (China); Zhou, Tieli [Changchun University, College of Food Engineering and Landscape Architecture (China); Sun, Chengbin; Tao, Yanchun; Lu, Fei; Wang, Xu; Zhao, Bing, E-mail: zhaob@mail.jlu.edu.cn [Jilin University, State Key Laboratory of Supramolecular Structure and Materials (China); Cui, Yinqiu, E-mail: cuiyq@jlu.edu.cn [Jilin University, School of Life Sciences (China)

    2015-10-15

    Composite films composed of polystyrene (PS) microsphere monolayers and gold (Au) and/or silver (Ag) nanoparticles (NPs) decorations were prepared by a novel size-dependent filtration effect on close-packed PS microsphere arrays. The uniform pores inlaid in the PS monolayer films acted as the transport tunnels for NPs. The steric restriction induced by the size of the pores was used as a main strategy to fabricate hybrid micro/nano films, which were composed of PS microspheres with inhomogeneous anisotropic decorations. The Au and Ag NPs were used as the building blocks to decorate the PS microspheres through a layer-by-layer self-assembly technique with the aid of polyelectrolyte coupling agents. Only the small particles which could pass through the micropores could reach to and deposit on the inner surfaces of the PS microsphere monolayer films. Large particles remained on the outside and could only deposit on the outer surfaces. Thus, the inhomogeneous anisotropic decoration was obtained. This study provides a novel strategy for fabricating anisotropic micro/nanostructures by the size-dependent filtration effect of NPs on porous films and has the potential in applications of anisotropic self-assembly, sensor, and surface modifications at nanoscale.

  10. Self-assembled monolayers of semifluorinated alkaneselenolates on noble metal substrates.

    Science.gov (United States)

    Shaporenko, A; Cyganik, P; Buck, M; Ulman, A; Zharnikov, M

    2005-08-30

    Self-assembled monolayers (SAMs) formed from semifluorinated dialkyldiselenol (CF(3)(CF(2))(5)(CH(2))(2)Se-)(2) (F6H2SeSeH2F6) on polycrystalline Au(111) and Ag(111) were characterized by high-resolution X-ray photoelectron spectroscopy, infrared reflection absorption spectroscopy, near edge X-ray absorption fine structure spectroscopy, scanning tunneling microscopy, and contact angle measurements. The Se-Se linkage of F6H2SeSeH2F6 was found to be cleaved upon the adsorption, followed by the formation of selenolate-metal bond. The resulting F6H2Se SAMs are well-ordered, densely packed, and contamination-free. The packing density of these films is governed by the bulky fluorocarbon part, which exhibits the expected helical conformation. A noncommensurate hexagonal arrangement of the F6H2Se molecules with an average nearest-neighbor spacing of about 5.8 +/- 0.2 A, close to the van der Waals diameter the fluorocarbon chain, was observed on Au(111). The orientation of the fluorocarbon chains in the F6H2Se SAMs does not depend on the substrate-the average tilt angle of these moieties was estimated to be about 21-22 degrees on both Au and Ag.

  11. Direct electrochemistry and electrocatalysis of horseradish peroxidase immobilized on L-glutathione self-assembled monolayers

    Institute of Scientific and Technical Information of China (English)

    Chuan Yin Liu; Ji Ming Hu

    2008-01-01

    A novel hydrogen peroxide biosensor has been fabricated based on covalently linked horseradish peroxidase (HRP) onto Lglutathione self-assembled monolayers (SAMs). The SAMs-based electrode was characterized by electrochemical methods, and direct electrochemistry of HRP can be achieved with formal potential of-0.242 V (vs. saturated Ag/AgCl) in pH7 phosphate buffer solution (PBS), the redox peak current is linear to scan rate and rate constant can be calculated to be 0.042 s-1. The HRP-SAMs-based biosensors show its better electrocatalysis to hydrogen peroxide in the concentration range of 1 × 10-6 mol/L to 1.2 × 10-3 mol/L with a detection limit of 4 × 10-7 mol/L. The apparent Michealis-Menten constant is 3.12 mmol/L. The biosensor can effectively eliminate the interferences of dopamine, ascorbic acid, uric acid, catechol and p-acetaminophen.

  12. A New Method For The Simulation Of Lipid Monolayer Dynamics

    CERN Document Server

    Griesbauer, J; Seeger, H M; Schneider, M F

    2010-01-01

    In this paper we present a predictive numerical model to describe dynamic properties of lipid monolayers. Its thermodynamic basis simply assumes a hexagonal lattice which can be occupied by lipids which may be ordered or disordered. Since the lattice sites are translational lose and interconnected by Newtonian springs, dynamic movements of the lipids are included. All necessary parameters directly follow from experiments. This approach allows the calculation of isotherms of lipid monolayers, which can be directly compared to experimentally determined ones, both quantitatively and qualitatively. Apart from that the monolayers heat capacity profile can be calculated, which otherwise cannot be easily extracted.

  13. Defect Structure of Localized Excitons in a WSe2 Monolayer

    KAUST Repository

    Zhang, Shuai

    2017-07-26

    The atomic and electronic structure of intrinsic defects in a WSe2 monolayer grown on graphite was revealed by low temperature scanning tunneling microscopy and spectroscopy. Instead of chalcogen vacancies that prevail in other transition metal dichalcogenide materials, intrinsic defects in WSe2 arise surprisingly from single tungsten vacancies, leading to the hole (p-type) doping. Furthermore, we found these defects to dominate the excitonic emission of the WSe2 monolayer at low temperature. Our work provided the first atomic-scale understanding of defect excitons and paved the way toward deciphering the defect structure of single quantum emitters previously discovered in the WSe2 monolayer.

  14. Ordered Porous Pd Octahedra Covered with Monolayer Ru Atoms.

    Science.gov (United States)

    Ge, Jingjie; He, Dongsheng; Bai, Lei; You, Rui; Lu, Haiyuan; Lin, Yue; Tan, Chaoliang; Kang, Yan-Biao; Xiao, Bin; Wu, Yuen; Deng, Zhaoxiang; Huang, Weixin; Zhang, Hua; Hong, Xun; Li, Yadong

    2015-11-25

    Monolayer Ru atoms covered highly ordered porous Pd octahedra have been synthesized via the underpotential deposition and thermodynamic control. Shape evolution from concave nanocube to octahedron with six hollow cavities was observed. Using aberration-corrected high-resolution transmission electron microscopy and X-ray photoelectron spectroscopy, we provide quantitative evidence to prove that only a monolayer of Ru atoms was deposited on the surface of porous Pd octahedra. The as-prepared monolayer Ru atoms covered Pd nanostructures exhibited excellent catalytic property in terms of semihydrogenation of alkynes.

  15. LEED I-V and DFT structure determination of the (√3 × √3)R30° Pb-Ag(111) surface alloy.

    Science.gov (United States)

    McLeod, I M; Dhanak, V R; Lahti, M; Matilainen, A; Pussi, K; Zhang, K H L

    2011-07-06

    The deposition of 1/3 of a monolayer of Pb on Ag(111) leads to the formation of PbAg(2) surface alloy with a long range ordered (√3 × √3)R30° superstructure. A detailed analysis of this structure using low-energy electron diffraction (LEED) I-V measurements together with density functional theory (DFT) calculations is presented. We find strong correlation between experimental and calculated LEED I-V data, with the fit between the two data sets having a Pendry's reliability factor of 0.21. The Pb atom is found to replace one top layer Ag atom in each unit cell, forming a substitutional PbAg(2) surface alloy, as expected, with the Pb atoms residing approximately 0.4 Å above the Ag atoms due to their size difference. DFT calculations are in good agreement with the LEED results.

  16. Preparation of Ag/HBP/PAN Nanofiber Web and Its Antimicrobial and Filtration Property

    Directory of Open Access Journals (Sweden)

    Li-Rong Yao

    2016-01-01

    Full Text Available To widen the application of nanofibers web in the field of medical health materials, a new Ag/amino-terminated hyperbranched polymer (HBP/polyacrylonitrile (PAN nanofiber web with excellent antimicrobial activity and filtration property was produced with Ag/HBP dispersion solution and PAN nanofiber. Ag/HBP dispersion solution was prepared with HBP as reducer and stabilizer, and Ag/HBP/PAN nanofiber was prepared by modifying electrospun PAN nanofiber with Ag/HBP aqueous solution. The characterization results showed that spherical Ag nanoparticles were prepared and they had a narrow distribution in HBP aqueous solution. The results of Ag/HBP/PAN nanofiber characterized with SEM and EDS showed that the content of silver nanoparticles on the surface of PAN nanofiber was on the increase when the treating temperature rose. The bacterial reduction rates of HBP-treated PAN nanofiber against S. aureus and E. coli were about 89%, while those of the Ag/HBP/PAN nanofiber against S. aureus and E. coli were 99.9% and 99.96%, respectively, due to the cooperative effects from the amino groups in HBP and Ag nanoparticles. Moreover, the small pores and high porosity in Ag/HBP/PAN nanofiber web resulted in high filtration efficiency (99.9% for removing smaller particles (0.1 μm~0.7 μm, which was much higher than that of the gauze mask.

  17. The disinfection performance and mechanisms of Ag/lysozyme nanoparticles supported with montmorillonite clay.

    Science.gov (United States)

    Jiang, Jing; Zhang, Chang; Zeng, Guang-Ming; Gong, Ji-Lai; Chang, Ying-Na; Song, Biao; Deng, Can-Hui; Liu, Hong-Yu

    2016-11-05

    The fabrication of montmorillonite (Mt) decorated with lysozyme-modified silver nanoparticles (Ag/lyz-Mt) was reported. The lysozyme (lyz) was served as both reducing and capping reagent. Coupling the bactericidal activity of the lyz with AgNPs, along with the high porous structure and large specific surface area of the Mt, prevented aggregation of AgNPs and promoted nanomaterial-bacteria interactions, resulting in a greatly enhanced bactericidal capability against both Gram positive and Gram negative bacteria. This paper systematically elucidated the bactericidal mechanisms of Ag/lyz-Mt. Direct contact between the Ag/lyz-Mt surface and the bacterial cell was essential to the disinfection. Physical disruption of bacterial membrane was considered to be one of the bactericidal mechanisms of Ag/lyz-Mt. Results revealed that Ag(+) was involved in the bactericidal activity of Ag/lyz-Mt via tests conducted using Ag(+) scavengers. A positive ROS (reactive oxygen species) scavenging test indirectly confirmed the involvement of ROS (O2(-), H2O2, and OH) in the bactericidal mechanism. Furthermore, the concentrations of individual ROS were quantified. Results showed that Ag/lyz-Mt nanomaterial could be a promising bactericide for water disinfection.

  18. Ozone decomposition on Ag/SiO{sub 2} and Ag/clinoptilolite catalysts at ambient temperature

    Energy Technology Data Exchange (ETDEWEB)

    Nikolov, Penko, E-mail: penmail@mail.bg [Institute of Catalysis, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria); Genov, Krassimir; Konova, Petya [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria); Milenova, Katya; Batakliev, Todor; Georgiev, Vladimir [Institute of Catalysis, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria); Kumar, Narendra [Laboratory of Industrial Chemistry, Process Chemistry Centre, Abo Akademi University, Biskopsgatan 8, 20500 Abo/Turku (Finland); Sarker, Dipak K. [School of Pharmacy and Biomolecular Sciences, University of Brighton, Lewes Road, Brighton BN2 4GJ (United Kingdom); Pishev, Dimitar [University of Chemical Technology and Metallurgy, 1756 Sofia (Bulgaria); Rakovsky, Slavcho [Institute of Catalysis, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria)

    2010-12-15

    Silver modified zeolite (Bulgarian natural clinoptilolite) and Ag/silica catalysts were synthesized by ion exchange and incipient wet impregnation method respectively and characterized by different techniques. DC arc-AES was used for Ag detection. XRD spectra show that Ag is loaded over the surface of the SiO{sub 2} sample and that after the ion-exchange process the HEU type structure of clinoptilolite is retained. UV-VIS (specific reflection at 310 nm) and IR (band at 695 cm{sup -1}) spectroscopy analysis proved that silver is loaded as a T-atom into zeolite channels as Ag{sup +}, instead of Na{sup +}, Ca{sup 2+}, or K{sup +} ions, existing in the natural clinoptilolite form. The samples Ag/SiO{sub 2} and Ag-clinoptilolite were tested as catalysts for decomposition of gas phase ozone. Very high catalytic activity (up to 99%) was observed and at the same time the catalysts remained active over time at room temperature.

  19. Size effects of Ag nanoparticles on plasmon-induced enhancement of photocatalysis of Ag-α-Fe₂O₃ nanocomposites.

    Science.gov (United States)

    Zhang, Shaofeng; Ren, Feng; Wu, Wei; Zhou, Juan; Sun, Lingling; Xiao, Xiangheng; Jiang, Changzhong

    2014-08-01

    Composite photocatalysts that consist of semiconductor and noble metal nanostructures have been considered to be the promising and crucial materials for straightforward improving the efficiency in photocatalytic process and for the conversion of solar to chemical energy. In this work, we fabricated Ag-α-Fe2O3 hybrid composites through a self-catalytic growth method by using the aldehyde-modified spindle α-Fe2O3 nanoparticles (NPs) as supports. The size of supported Ag NPs can be directly controlled on the surface of α-Fe2O3. The morphology and structure of the resulting Ag-α-Fe2O3 hybrid composites were studied by various techniques, including SEM, TEM, and XRD. The distinct photocatalytic behaviors were examined through the photodegradation of RhB dye. It was found that with the Ag NPs, the photocatalytic activities were enhanced greatly and the size of the Ag NPs played a crucial influence on the photocatalytic behaviors of the Ag-α-Fe2O3 composites.

  20. Photopatterning of stable, low-density, self-assembled monolayers on gold.

    Science.gov (United States)

    Safazadeh, Leila; Berron, Brad J

    2015-03-10

    Photoinitiated thiol-yne chemistry is utilized as a click reaction for grafting of acid-terminated alkynes to thiol-terminated monolayers on a gold substrate to create stable, low-density monolayers. The resulting monolayers are compared with a well-packed 11-mercaptoundecanoic acid monolayer and the analogous low-density monolayers prepared through a solution phase synthetic approach. The overall structuring of the monolayer prepared by solid-phase grafting is characterized by contact angle goniometry and Fourier transform infrared spectroscopy. The results show that the product monolayer has an intermediate surface energy and a more disordered chemical structuring compared to a traditional well-packed self-assembled monolayer, showing a low-packing density of the chains at the monolayer surface. The monolayer's structure and electrochemical stability were studied by reductive desorption of the thiolates. The prepared low-density monolayers have a higher electrochemical stability than traditional well-packed monolayers, which results from the crystalline structure at the gold interface. This technique allows for simple, fast preparation of low-density monolayers of higher stability than well-packed monolayers. The use of a photomask to restrict light access to the substrate yielded these low-density monolayers in patterned regions defined by light exposure. This general thiol-yne approach is adaptable to a variety of analogous low-density monolayers with diverse chemical functionalities.

  1. β-丙氨酸-银复合膜修饰电极用于循环伏安法测定对乙酰氨基酚%CV Determination of p-Acetaminophenol with the Composite Film Modified Electrode of Ag-AIa/GCE

    Institute of Scientific and Technical Information of China (English)

    王朝霞; 陈美凤; 马心英

    2012-01-01

    The β-alanine and silver composite film modified glassed carbon electrode (Ag-Ala/GCE) was prepared and the electrochemical property of the modified electrode vs. p-acetaminophenol (ACOP) was studied by cyclic voltammetry. It was found that ACOP showed a pair of redox peaks in PBS of pH 4. 0 and based on this finding, a selectrive method for determination of ACOP by cyclic voltammetry was proposed. Linear relationship between values of peak current and concentration of ACOP was ranged from 6.0×10^-7~7.0×10^-4mol·L-1, with detection limit (3S/N) of 2.0×10^-7mol·L-1. The proposed method was used in the determination of ACOP in medicament, and test for recovery was made by standard addition method, giving values of recovery in the range of 95.1%~101.6%%制备了β丙氨酸-银复合膜修饰电极(Ag—Ala/GCE),采用循环伏安法研究了对乙酰氨基酚在修饰电极上的电化学行为。结果表明:在pH4.0的磷酸盐缓冲液中,对乙酰氨基酚在修饰电极上呈现一对灵敏的氧化还原峰,提出了用循环伏安法测定对乙酰氨基酚的含量。对乙酰氨基酚浓度在6.0×10^-7~7.0×10^-4mol·L-1范围内与氧化峰电流呈现线性关系,检出限(3S/N)为2.0×10^-7mol·L-1。修饰电极用于药剂中对乙酰氨基酚的测定,并用标准加入法测得方法的回收率在95.1%~101.6%之间。

  2. Ag-Air Service

    Science.gov (United States)

    1981-01-01

    Econ, Inc.'s agricultural aerial application, "ag-air," involves more than 10,000 aircraft spreading insecticides, herbicides, fertilizer, seed and other materials over millions of acres of farmland. Difficult for an operator to estimate costs accurately and decide what to charge or which airplane can handle which assignment most efficiently. Computerized service was designed to improve business efficiency in choice of aircraft and determination of charge rates based on realistic operating cost data. Each subscriber fills out a detailed form which pertains to his needs and then receives a custom-tailored computer printout best suited to his particular business mix.

  3. Preparation and antibacterial activities of Ag/Ag+/Ag3+ nanoparticle composites made by pomegranate (Punica granatum) rind extract

    Science.gov (United States)

    Yang, Hui; Ren, Yan-yu; Wang, Tao; Wang, Chuang

    Nano-silver and its composite materials are widely used in medicine, food and other industries due to their strong conductivity, size effect and other special performances. So far, more microbial researches have been applied, but a plant method is rarely reported. In order to open up a new way to prepare AgNP composites, pomegranate peel extract was used in this work to reduce Ag+ to prepare Ag/Ag+/Ag3+ nanoparticle composites. UV-Vis was employed to detect and track the reduction of Ag+ and the forming process of AgNPs. The composition, structure and size of the crystal were analyzed by XRD and TEM. Results showed that, under mild conditions, pomegranate peel extract reacted with dilute AgNO3 solution to produce Ag/Ag+/Ag3+ nanoparticle composites. At pH = 8 and 10 mmol/L of AgNO3 concentration, the size of the achieved composites ranged between 15 and 35 nm with spherical shapes and good crystallinity. The bactericidal experiment indicated that the prepared Ag/Ag+/Ag3+ nanoparticles had strong antibacterial activity against gram positive bacteria and gram negative bacteria. FTIR analysis revealed that biological macromolecules with groups of sbnd NH2, sbnd OH, and others were distributed on the surface of the newly synthesized Ag/Ag+/Ag3+ nanoparticles. This provided a useful clue to further study the AgNP biosynthesis mechanism.

  4. Structure of solid monolayers and multilayers of -hexane on graphite

    Indian Academy of Sciences (India)

    M Krishnan; S Balasubramanian; S Clarke

    2003-10-01

    We present all-atom molecular dynamics simulations of -hexane on the basal plane of graphite at monolayer and multilayer coverages. In keeping with experimental data, we find the presence of ordered adsorbed layers both at single monolayer coverage and when the adsorbed layer coexists with excess liquid adsorbate. Using a simulation method that does not impose any particular periodicity on the adsorbed layer, we quantitatively compare our results to the results of neutron diffraction experiments and find a structural transition from a uniaxially incommensurate lattice to a fully commensurate structure on increasing the coverage from a monolayer to a multilayer. The zig-zag backbone planes of all the alkane molecules lie parallel to the graphite surface at the multilayer coverage, while a few molecules are observed to attain the perpendicular orientation at monolayer coverage.

  5. Monolayer MoS2 heterojunction solar cells

    KAUST Repository

    Tsai, Menglin

    2014-08-26

    We realized photovoltaic operation in large-scale MoS2 monolayers by the formation of a type-II heterojunction with p-Si. The MoS 2 monolayer introduces a built-in electric field near the interface between MoS2 and p-Si to help photogenerated carrier separation. Such a heterojunction photovoltaic device achieves a power conversion efficiency of 5.23%, which is the highest efficiency among all monolayer transition-metal dichalcogenide-based solar cells. The demonstrated results of monolayer MoS 2/Si-based solar cells hold the promise for integration of 2D materials with commercially available Si-based electronics in highly efficient devices. © 2014 American Chemical Society.

  6. Unsupported single-atom-thick copper oxide monolayers

    Science.gov (United States)

    Yin, Kuibo; Zhang, Yu-Yang; Zhou, Yilong; Sun, Litao; Chisholm, Matthew F.; Pantelides, Sokrates T.; Zhou, Wu

    2017-03-01

    Oxide monolayers may present unique opportunities because of the great diversity of properties of these materials in bulk form. However, reports on oxide monolayers are still limited. Here we report the formation of single-atom-thick copper oxide layers with a square lattice both in graphene pores and on graphene substrates using aberration-corrected scanning transmission electron microscopy. First-principles calculations find that CuO is energetically stable and its calculated lattice spacing matches well with the measured value. Furthermore, free-standing copper oxide monolayers are predicted to be semiconductors with band gaps ∼3 eV. The new wide-bandgap single-atom-thick copper oxide monolayers usher a new frontier to study the highly diverse family of two-dimensional oxides and explore their properties and their potential for new applications.

  7. Membrane Insertion by Trichosanthin Using the Monolayer Method

    Institute of Scientific and Technical Information of China (English)

    薛毅; 夏晓峰; 隋森芳

    2003-01-01

    A monolayer technique was used to investigate the interaction between the ribosome inactivating protein trichosanthin (TCS) and phospholipid membrane.The adsorption experiments show that the negatively charged 1,2-dipalmitoyl-sn-glycerol-3-phosphoglycerol (DPPG) causes obvious enrichment of TCS beneath the monolayer, indicating electrostatic attraction between TCS and the negatively charged phospholipid.When TCS was incorporated into the DPPG monolayer at low pH, it could not be completely squeezed out until the monolayer collapsed.The results suggest that the electrostatic attraction and the hydrophobic force are involved in the interaction between TCS and phospholipids at different stages.These findings may be correlated with the membrane translocation mechanism of TCS.

  8. Experimental study of thermal rectification in suspended monolayer graphene

    Science.gov (United States)

    Wang, Haidong; Hu, Shiqian; Takahashi, Koji; Zhang, Xing; Takamatsu, Hiroshi; Chen, Jie

    2017-06-01

    Thermal rectification is a fundamental phenomenon for active heat flow control. Significant thermal rectification is expected to exist in the asymmetric nanostructures, such as nanowires and thin films. As a one-atom-thick membrane, graphene has attracted much attention for realizing thermal rectification as shown by many molecular dynamics simulations. Here, we experimentally demonstrate thermal rectification in various asymmetric monolayer graphene nanostructures. A large thermal rectification factor of 26% is achieved in a defect-engineered monolayer graphene with nanopores on one side. A thermal rectification factor of 10% is achieved in a pristine monolayer graphene with nanoparticles deposited on one side or with a tapered width. The results indicate that the monolayer graphene has great potential to be used for designing high-performance thermal rectifiers for heat flow control and energy harvesting.

  9. Tribological properties of OTS self-assembled monolayers

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Octadecyltrichlorosilane (OTS) self-assembled monolayers (SAMs)were prepared on the substrates of silicon and glass. The tribological properties were tested with a self-made point-contact pure sliding micro tribometer. The effect of humidity on the tribological properties of both OTS SAMs and the naked substrates were studied. When the substrate is covered by OTS monolayer, the friction coefficient is reduced from 0.5 to 0.1 and the stick-slip phenomenon is weakened. OTS monolayer can keep its friction coefficient steady in a wide range of humidity, because it is highly hydrophobic and thus not sensitive to humidity. In addition, the OTS monolayer has a considerable anti-wear ability.

  10. Coexistence of multiple conformations in cysteamine monolayers on Au(111)

    DEFF Research Database (Denmark)

    Zhang, Jingdong; Bilic, A; Reimers, JR

    2005-01-01

    The structural organization, catalytic function, and electronic properties of cysteamine monolayers on Au(111) have been addressed comprehensively by voltammetry, in situ scanning tunneling microscopy (STM) in anaerobic environment, and a priori molecular dynamics (MD) simulation and STM image si...

  11. Self-assembled monolayer as an interfacial modification material for highly efficient and air-stable inverted organic solar cells

    Science.gov (United States)

    Song, Myungkwan; Kang, Jae-Wook; Kim, Dong-Ho; Kwon, Jung-Dae; Park, Sung-Gyu; Nam, Sanggil; Jo, Sungjin; Yoon Ryu, Seung; Su Kim, Chang

    2013-04-01

    Organic solar cells with inverted structures can greatly improve photovoltaic stability. This paper reports a method to lower the work function of indium tin oxide (ITO) in inverted organic solar cells by modification with ultrathin 3-aminopropyltriethoxysilane (APTES) monolayers. The device studies showed that the resulting photovoltaic efficiencies were significantly increased from 0.64% to 4.83% with the use of the APTES monolayer, which could be attributed to the dramatic enhancement in the open-circuit voltage and fill factor. The effective electron selectivity in the case of the APTES-modified ITO could be attributed to the reduction of the work function of ITO as a result of the electron-donating nature of the amine groups in the APTES monolayer. The power conversion efficiency of the unencapsulated inverted organic solar cells with APTES-modified ITO remained above 80% of their original values even after storage in air for thirty days. Our results provide a promising approach to improve the performance of highly efficient and air-stable inverted organic solar cells.

  12. Adhesive and conformational behaviour of mycolic acid monolayers

    OpenAIRE

    2010-01-01

    We have studied the pH-dependent interaction between mycolic acid (MA) monolayers and hydrophobic and hydrophilic surfaces using molecular (colloidal probe) force spectroscopy. In both cases, hydrophobic and hydrophilic monolayers (prepared by Langmuir-Blodgett and Langmuir-Schaefer deposition on silicon or hydrophobized silicon substrates, respectively) were studied. The force spectroscopy data, fitted with classical DLVO (Derjaguin, Landau, Verwey, and Overbeek) theory to examine the contri...

  13. Specific Ion Effects in Cholesterol Monolayers

    Directory of Open Access Journals (Sweden)

    Teresa Del Castillo-Santaella

    2016-05-01

    Full Text Available The interaction of ions with interfaces and, in particular, the high specificity of these interactions to the particular ions considered, are central questions in the field of surface forces. Here we study the effect of different salts (NaI, NaCl, CaCl2 and MgCl2 on monolayers made of cholesterol molecules, both experimentally (surface area vs. lateral pressure isotherms measured by a Langmuir Film Balance and theoretically (molecular dynamics (MD all-atomic simulations. We found that surface isotherms depend, both quantitatively and qualitatively, on the nature of the ions by altering the shape and features of the isotherm. In line with the experiments, MD simulations show clear evidences of specific ionic effects and also provide molecular level details on ion specific interactions with cholesterol. More importantly, MD simulations show that the interaction of a particular ion with the surface depends strongly on its counterion, a feature ignored so far in most theories of specific ionic effects in surface forces.

  14. Surface dilatational viscosity of Langmuir monolayers

    Science.gov (United States)

    Lopez, Juan; Vogel, Michael; Hirsa, Amir

    2003-11-01

    With increased interest in microfluidic systems, interfacial phenomena is receiving more attention. As the length scales of fluid problems decrease, the surface to volume ratio increases and the coupling between interfacial flow and bulk flow becomes increasingly dominated by effects due to intrinsic surface viscosities (shear and dilatational), in comparison to elastic effects (due to surface tension gradients). The surface shear viscosity is well-characterized, as cm-scale laboratory experiments are able to isolate its effects from other interfacial processes (e.g., in the deep-channel viscometer). The same is not true for the dilatational viscosity, because it acts in the direction of surface tension gradients. Their relative strength scale with the capillary number, and for cm-scale laboratory flows, surface tension effects tend to dominate. In microfluidic scale flows, the scaling favors viscosity. We have devised an experimental apparatus which is capable of isolating and enhancing the effects of dilatational viscosity at the cm scales by driving the interface harmonically in time, while keeping the interface flat. In this talk, we shall present both the theory for how this works as well as experimental measurements of surface velocity from which we deduce the dilatational viscosity of several monolayers on the air-water interface over a substantial range of surface concentrations. Anomalous behavior over some range of concentration, which superficially indicates negative viscosity, maybe explained in terms of compositional effects due to large spatial and temporal variations in concentration and corresponding viscosity.

  15. Induction of homochirality in achiral enantiomorphous monolayers.

    Science.gov (United States)

    Parschau, Manfred; Romer, Sara; Ernst, Karl-Heinz

    2004-12-01

    We report the induction of homochirality in enantiomorphous layers of achiral succinic acid on a Cu(110) surface after doping with tartaric acid (TA) enantiomers. Succinic acid becomes chiral upon adsorption due to symmetry-breaking interactions with the Cu(110) surface. The doubly deprotonated bisuccinate forms mirror domains on the surface, which leads to a superposition of (11,-90) and (90,-11) patterns observed by low-energy electron diffraction (LEED). On average, however, the surface layer is racemic. An amount of 2 mol % of (R,R)- or (S,S)-tartaric acid in the monolayer, corresponding to an absolute coverage of 0.001 tartaric acid molecule per surface copper atom, is sufficient to make the LEED spots of one enantiomorphous lattice disappear. After thermally induced desorption of TA, the succinic acid lattice turns racemic again. In analogy to the "sergeants-and-soldiers" principle described for helical polymers, this effect is explained by a lateral cooperative interaction within the two-dimensional lattice.

  16. Structural phase transitions in monolayer molybdenum dichalcogenides

    Science.gov (United States)

    Choe, Duk-Hyun; Sung, Ha June; Chang, Kee Joo

    2015-03-01

    The recent discovery of two-dimensional materials such as graphene and transition metal dichalcogenides (TMDs) has provided opportunities to develop ultimate thin channel devices. In contrast to graphene, the existence of moderate band gap and strong spin-orbit coupling gives rise to exotic electronic properties which vary with layer thickness, lattice structure, and symmetry. TMDs commonly appear in two structures with distinct symmetries, trigonal prismatic 2H and octahedral 1T phases which are semiconducting and metallic, respectively. In this work, we investigate the structural and electronic properties of monolayer molybdenum dichalcogenides (MoX2, where X = S, Se, Te) through first-principles density functional calculations. We find a tendency that the semiconducting 2H phase is more stable than the metallic 1T phase. We show that a spontaneous symmetry breaking of 1T phase leads to various distorted octahedral (1T') phases, thus inducing a metal-to-semiconductor transition. We discuss the effects of carrier doping on the structural stability and the modification of the electronic structure. This work was supported by the National Research Foundation of Korea (NRF) under Grant No. NRF-2005-0093845 and Samsung Science and Technology Foundation under Grant No. SSTFBA1401-08.

  17. Effect of different polymers on morphology and particle size of silver nanoparticles synthesized by modified polyol method

    Science.gov (United States)

    Fereshteh, Zeinab; Rojaee, Ramin; Sharifnabi, Ali

    2016-10-01

    In this work, simple, economic, eco-friendly modified method with high efficiency was applied for synthesis of silver nanoparticles (Ag NPs) by using polyethylene glycol (PEG) as a capping agent, reductant, and media agent. In order to preparation uniform and small Ag NPs, the reaction parameters such as type of polymer, AgNO3/Polymer weight concentration ratio, and AgNO3/NaBH4 molar concentration ratio were modified. The best condition was optimized in concentration ratio of AgNO3: PEG: NaBH4 where are 1:10:0.01, respectively with 82% efficiency and 98.95% purity. Therefore, this modified polyol method can also be scaled up for synthesis of Ag NPs appropriately. Due to polymeric coating on the Ag NPs, they can be employed as a promising candidate for drug delivery systems.

  18. Thermoelectric properties of SnSe2 monolayer

    Science.gov (United States)

    Li, Guanpeng; Ding, Guangqian; Gao, Guoying

    2017-01-01

    The 2H (MoS2-type) phase of 2D transition metal dichalcogenides (TMDCs) has been extensively studied and exhibits excellent electronic and optoelectronic properties, but the high phonon thermal conductivity is detrimental to the thermoelectric performances. Here, we use first-principles methods combined with Boltzmann transport theory to calculate the electronic and phononic transport properties of 1T (CdI2-type) SnSe2 monolayer, a recently realized 2D metal dichalcogenide semiconductor. The calculated band gap is 0.85 eV, which is a little larger than the bulk value. Lower phonon thermal conductivity and higher power factor are obtained in 1T-SnSe2 monolayer compared to 2H-TMDCs monolayers. The low phonon thermal conductivity (3.27 W mK-1 at room temperature) is mainly due to the low phonon frequency of acoustic modes and the coupling of acoustic modes with optical modes. We also find that the p-type has better thermoelectric performance than the n-type, and the figure of merit within p-type can reach 0.94 at 600 K for 1T-SnSe2 monolayer, which is higher than those of most 2H-TMDCs monolayers, making 1T-SnSe2 monolayer a promising candidate for thermoelectric applications.

  19. Treponema pallidum Invades Intercellular Junctions of Endothelial Cell Monolayers

    Science.gov (United States)

    Thomas, D. Denee; Navab, Mahamad; Haake, David A.; Fogelman, Alan M.; Miller, James N.; Lovett, Michael A.

    1988-05-01

    The pathogenesis of syphilis reflects invasive properties of Treponema pallidum, but the actual mode of tissue invasion is unknown. We have found two in vitro parallels of treponemal invasiveness. We tested whether motile T. pallidum could invade host cells by determining the fate of radiolabeled motile organisms added to a HeLa cell monolayer; 26% of treponemes associated with the monolayer in a trypsin-resistant niche, presumably between the monolayer and the surface to which it adhered, but did not attain intracellularity. Attachment of T. pallidum to cultured human and rabbit aortic and human umbilical vein endothelial cells was 2-fold greater than to HeLa cells. We added T. pallidum to aortic endothelial cells grown on membrane filters under conditions in which tight intercellular junctions had formed. T. pallidum was able to pass through the endothelial cell monolayers without altering tight junctions, as measured by electrical resistance. In contrast, heat-killed T. pallidum and the nonpathogen Treponema phagedenis biotype Reiter failed to penetrate the monolayer. Transmission electron micrographs of sections of the monolayer showed T. pallidum in intercellular junctions. Our in vitro observations suggest that these highly motile spirochetes may leave the circulation by invading the junctions between endothelial cells.

  20. Optoelectronics of Transition Metal Dichalcogenide Monolayers and Heterostructures

    Science.gov (United States)

    Schaibley, John

    2015-03-01

    Monolayer transition metal dichalcogenides (TMDs) contain 2D valley excitons which reside in two degenerate momentum space valleys at the edges of the Brillouin zone. It is crucially important to understand fundamental 2D exciton properties in TMD monolayers and van der Waals heterostructures. By performing coherent nonlinear optical spectroscopy with high spectral resolution, we observe nanosecond decay dynamics in single monolayers of MoSe2, implying the presence of a previously unreported long-lived state that appears to trap the exciton population. In MoSe2-WSe2 vertical heterostructures, we observe intralayer excitons, where the electron and hole are confined to different monolayers, and show evidence of strong exciton-exciton interaction effects and long lifetimes. Based on TMD monolayer excitons, we have also investigated a variety of fundamental quantum devices, including a nano-cavity laser and a second-harmonic generation transistor. Finally, we report a new type of single quantum emitter, based on single localized excitons spatially confined to defects in monolayers of WSe2. The photoluminescence from these localized excitons is spectrally narrow and shows strong anti-bunching, demonstrating the single photon nature of the emission.

  1. Manipulation of electronic structure in WSe2 monolayer by strain

    Science.gov (United States)

    Yang, Cong-xia; Zhao, Xu; Wei, Shu-yi

    2016-11-01

    In this paper, we study the electronic properties of WSe2 monolayer with biaxial tensile strain and compressive strain by using first principles based on the density function theory. Under the biaxial tensile strain, WSe2 monolayer retains direct band gap with increasing strain and the band gap of WSe2 continuously decreases with increasing strain, eventually turn to metal when strain is equal to or more than 13%. Under the biaxial compressive strain, WSe2 monolayer turns to indirect gap and the band gap continuously decreases with increasing strain, finally turn to metal when strain is up to -7%. The strain can reduce the band gap of the WSe2 monolayer regardless of the strain direction. By comparison, we can see that the tensile strain appears to be more effective in reducing the band gap of pristine WSe2 monolayer than the compressive strain from -5% to 5%. But the band gap turns to zero quickly from -6% to -7% under compressive strain, however for tensile strain from 5% to 13%, the band gap decreases slowly. Based on the further analysis of the projected charge density for WSe2 monolayer, the fundamental reason of the change of band structure under biaxial tensile strain is revealed.

  2. Nonlinear optical characteristics of monolayer MoSe{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Le, Chinh Tam; Ullah, Farman; Senthilkumar, Velusamy; Kim, Yong Soo [Department of Physics and Energy Harvest Storage Research Center, University of Ulsan (Korea, Republic of); Clark, Daniel J.; Jang, Joon I. [Department of Physics, Applied Physics and Astronomy, Binghamton University, Binghamton, NY (United States); Sim, Yumin; Seong, Maeng-Je [Department of Physics, Chung-Ang University, Seoul (Korea, Republic of); Chung, Koo-Hyun [School of Mechanical Engineering, University of Ulsan (Korea, Republic of); Park, Hyoyeol [Electronics, Communication and Semiconductor Applications Department, Ulsan College (Korea, Republic of)

    2016-08-15

    In this study, we utilized picosecond pulses from an Nd:YAG laser to investigate the nonlinear optical characteristics of monolayer MoSe{sub 2}. Two-step growth involving the selenization of pulsed-laser-deposited MoO{sub 3} film was employed to yield the MoSe{sub 2} monolayer on a SiO{sub 2}/Si substrate. Raman scattering, photoluminescence (PL) spectroscopy, and atomic force microscopy verified the high optical quality of the monolayer. The second-order susceptibility χ{sup (2)} was calculated to be ∝50 pm V{sup -1} at the second harmonic wavelength λ{sub SHG} ∝810 nm, which is near the optical gap of the monolayer. Interestingly, our wavelength-dependent second harmonic scan can identify the bound excitonic states including negatively charged excitons much more efficiently, compared with the PL method at room temperature. Additionally, the MoSe{sub 2} monolayer exhibits a strong laser-induced damage threshold ∝16 GW cm{sup -2} under picosecond-pulse excitation{sub .} Our findings suggest that monolayer MoSe{sub 2} can be considered as a promising candidate for high-power, thin-film-based nonlinear optical devices and applications. (copyright 2016 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. Structural and electronic properties of arsenic nitrogen monolayer

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Pei; Nie, Yao-zhuang, E-mail: yznie@csu.edu.cn; Xia, Qing-lin; Guo, Guang-hua, E-mail: guogh@mail.csu.edu.cn

    2017-03-26

    We present our first-principles calculations of a new two-dimensional material, arsenic nitrogen monolayer. The structural, electronic, and mechanical properties are investigated in detail by means of density functional theory computations. The calculated binding energy and the phonon spectra demonstrate that the AsN can form stable monolayer in puckered honeycomb structure. It is a semiconductor with indirect band gap of 0.73 eV, and displays highly anisotropic mechanical properties. Strain has obvious influence on the electronic properties of AsN monolayer. It is found that in the armchair direction, a moderate compression strain (−12%) can trigger an indirect to direct band gap transition and a tensile strain of 18% can make the AsN becoming a stable metal. In the zigzag direction, a rather smaller strain than armchair direction (12% for compression and 8% for stretch) can induce the indirect band gap to metal transition. - Highlights: • A new two-dimensional material, arsenic nitrogen monolayer is predicated by first-principles calculations. • Arsenic nitrogen monolayer displays highly anisotropic mechanical properties. • Electronic structures of arsenic nitrogen monolayer can be effectively manipulated by applied strains.

  4. Germanium adsorption on Ag(111): an AES-LEED and STM study.

    Science.gov (United States)

    Oughaddou, H; Mayne, A; Aufray, B; Bibérian, J P; Le Lay, G; Ealet, B; Dujardin, G; Kara, A

    2007-09-01

    The adsorption of germanium on Ag(111) has been investigated using Scanning Tunneling Microscopy, Auger Electron Spectroscopy and Low Energy Electron Diffraction. From the shape of the Auger peak-to-peak versus time curves, we deduce that at room temperature the growth mode is nearly layer-by-layer at least for the first two layers. In the sub-monolayer range, the growth starts by the formation of a (mean square root of 3 x mean square root of 3)R30 degrees surface superstructure which is complete at 1/3 monolayer coverage. Beyond this coverage a rectangular c(mean square root of 3 x 7) superstructure is observed. STM images reveal that this last reconstruction is formed by an ordered arrangement of self-assembled Ge tetramers giving rise to a surprising undulation of the surface.

  5. SiO{sub x} monolayer overcoating effect on the TiO{sub 2} photocatalytic oxidation of cetylpyridinium bromide

    Energy Technology Data Exchange (ETDEWEB)

    Tada, Hiroaki; Kubo, Yasuyuki; Akazawa, Manabu; Ito, Seishiro

    2000-01-15

    The effect of SiO{sub x} monolayer coverage on the rate of TiO{sub 2} photocatalytic oxidation of cetylpyridinium bromide (CPB) in aqueous solutions has been studied. The rate of CPB removal from the solution (5 < pH < 7) increases with the surface modification at concentrations below 4.5 x 10{sup {minus}4} M and its promoting effect is enhanced with decreasing concentration. A modified Langmuir-Hinshelwood model, where the rate of surface reaction is assumed to be proportional to the coverage of CPB at the photostationary state is proposed for dilute reaction systems. As a result of the kinetic analyses, the acceleration of the reaction with the SiO{sub x} monolayer coverage can be attributed to the increase in the rate of adsorption due to the electrostatic attraction of cetylpyridinium ion. The suppression of Br{sup {minus}} adsorption is also suggested as a minor contribution.

  6. Study of the ability of self-assembled N-vinylcarbazole monolayers to protect copper against corrosion

    Directory of Open Access Journals (Sweden)

    NAI-XING WANG

    2002-10-01

    Full Text Available N-Vinylcarbazole (NVC monolayers were self-assembled on copper surfaces. The electrochemical properties of the copper surfaces modified by NVC self-assembled monolayers (SAMs were investigated using polarization and electrochemical impedance spectroscopic (EIS methods. The polarization measurements indicated that the NVC SAMs could reduce the rates of the anodic and cathodic reaction on the surface of copper electrodes in 0.5 mol dm-3 NaCl solution. The EIS results showed the NVC formed a closely packed film that was able to inhibit copper corrosion. X-Ray photoelectron spectroscopy (XPS analysis of the copper samples and atomic adsorption analysis of the solution showed that the copper surfaces were covered by NVC SAMs, and the adsorption of NVC on the copper surfaces was accompanied with dissolution of Cu into the solution.

  7. High-Yield Excited Triplet States in Pentacene Self-Assembled Monolayers on Gold Nanoparticles through Singlet Exciton Fission.

    Science.gov (United States)

    Kato, Daiki; Sakai, Hayato; Tkachenko, Nikolai V; Hasobe, Taku

    2016-04-18

    One of the major drawbacks of organic-dye-modified self-assembled monolayers on metal nanoparticles when employed for efficient use of light energy is the fact that singlet excited states on dye molecules can be easily deactivated by means of energy transfer to the metal surface. In this study, a series of 6,13-bis(triisopropylsilylethynyl)pentacene-alkanethiolate monolayer protected gold nanoparticles with different particle sizes and alkane chain lengths were successfully synthesized and were employed for the efficient generation of excited triplet states of the pentacene derivatives by singlet fission. Time-resolved transient absorption measurements revealed the formation of excited triplet states in high yield (172±26 %) by suppressing energy transfer to the gold surface.

  8. Employing X-ray Photoelectron Spectroscopy for Determining Layer Homogeneity in Mixed Polar Self-Assembled Monolayers.

    Science.gov (United States)

    Hehn, Iris; Schuster, Swen; Wächter, Tobias; Abu-Husein, Tarek; Terfort, Andreas; Zharnikov, Michael; Zojer, Egbert

    2016-08-04

    Self-assembled monolayers (SAMs) containing embedded dipolar groups offer the particular advantage of changing the electronic properties of a surface without affecting the SAM-ambient interface. Here we show that such systems can also be used for continuously tuning metal work functions by growing mixed monolayers consisting of molecules with different orientations of the embedded dipolar groups. To avoid injection hot-spots when using the SAM-modified electrodes in devices, a homogeneous mixing of the two components is crucial. We show that a combination of high-resolution X-ray photoelectron spectroscopy with state-of-the-art simulations is an ideal tool for probing the electrostatic homogeneity of the layers and thus for determining phase separation processes in polar adsorbate assemblies down to inhomogeneities at the molecular level.

  9. Construction of Ag/AgCl nanostructures from Ag nanoparticles as high-performance visible-light photocatalysts

    Science.gov (United States)

    Yang, Fan; Liu, Dongzhi; Wang, Tianyang; Li, Wei; Hu, Wenping; Zhou, Xueqin

    2016-11-01

    A combined strategy of in situ oxidation and assembly is developed to prepare Ag/AgCl nanospheres and nanocubes from Ag nanoparticles under room temperature. It is a new facile way to fabricate Ag/AgCl with small sizes and defined morphologies. Ag/AgCl nanospheres with an average size of 80 nm were achieved without any surfactants, while Ag/AgCl nanocubes with a mean edge length of 150 nm were obtained by introduction of N-dodecyl- N, N-dimethyl-2-ammonio-acetate. The possible formation mechanism involves the self-assembly of AgCl nanoparticles, Ostwald ripening and photoreduction of Ag+ into Ag0 by the room light. The as-prepared Ag/AgCl nanospheres and nanocubes exhibit excellent photocatalytic activity and stability toward degradation of organic pollutants under visible-light irradiation. It is demonstrated that Ag/AgCl nanocubes display enhanced photocatalytic activity in comparison with Ag/AgCl nanospheres due to the more efficient charge transfer. This work may pave an avenue to construct various functional materials via the assembly strategy using nanoparticles as versatile building blocks.

  10. About AgEcon Search

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>AgEcon Search is a free,open access repository of full-text scholarly literature in agricultural and applied economics,including working papers,conference papers,and journal articles. AgEcon Search is co-sponsored by the Department of Applied Economics and

  11. About AgEcon Search

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>AgEcon Search is a free,open access repository of full-text scholarly literature in agricultural and applied economics,including working papers,conference papers,and journal articles.AgEcon Search is co-sponsored by the Department of Applied Economics andthe University Libraries

  12. About AgEcon Search

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>AgEcon Search is a free,open access repository of full-text scholarly literature in agricultural and applied economics,including working papers,conference papers,and journal articles. AgEcon Search is cosponsored by the Department of Applied Economics and the University Libraries at University of Minnesota and the Agricultural and Applied Economics Association.

  13. About AgEcon Search

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    <正>AgEcon Search is a free,open access repository of full-text scholarly literature in agricultural and applied economics,including working papers,conference papers,and journal articles. AgEcon Search is co-sponsored by the Department of Applied Economics and the University Libraries at University of Minnesota and the Agricultural and Applied

  14. About AgEcon Search

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    <正>AgEcon Search is a free,open access repository of full-text scholarly literature in agricultural and applied economics,including working papers,conference papers,and journal articles.AgEcon Search is co-sponsored by the Department of Applied Economics and the University Libraries

  15. About AgEcon Search

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>AgEcon Search is a free,open access repository of full-text scholarly literature in agricultural and applied economics,including working papers,conference papers,and journal articles. AgEcon Search is co-sponsored by the Department of Applied Economics and the University Libraries at University of Minnesota and the Agricultural and Applied Economics Association. Research

  16. About AgEcon Search

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>AgEcon Search is a free,open access repository of full-text scholarly literature in agricultural and applied economics,including working papers,conference papers,and journal articles. AgEcon Search is co-sponsored by the Department of Applied E-

  17. AGS Experiments: 1989, 1990, 1991

    Energy Technology Data Exchange (ETDEWEB)

    Depken, J.C.

    1992-02-01

    This report contains: Experimental areas layout; table of beam parameters and fluxes; experiment schedule ``as run``; proposed 1992 schedule; a listing of experiments by number; two-page summaries of each experiment begin here, also ordered by number; publications of AGS Experiments begin here; and list of AGS Experimenters begins here.

  18. AGS Experiments: 1989, 1990, 1991

    Energy Technology Data Exchange (ETDEWEB)

    Depken, J.C.

    1992-02-01

    This report contains: Experimental areas layout; table of beam parameters and fluxes; experiment schedule as run''; proposed 1992 schedule; a listing of experiments by number; two-page summaries of each experiment begin here, also ordered by number; publications of AGS Experiments begin here; and list of AGS Experimenters begins here.

  19. About AgEcon Search

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>AgEcon Search is a free, open access repository of full-text scholarly literature in agricultural and applied economics, including working papers, conference papers, and journal articles.AgEcon Searchis co-sponsored by the Department of Applied E

  20. Ag@AgCl-TiO2-粉煤灰微珠复合光催化剂的制备及其可见光光催化性能%Preparation of Ag@AgCl-TiO2-Flyash Microspheres Composite Photocatalyst and Its Photocatalytic Property under Visible Light

    Institute of Scientific and Technical Information of China (English)

    郭凌坤; 吕珺; 周嵩; 汪冬梅; 徐光青; 郑治祥; 吴玉程

    2012-01-01

    Ag@AgCl nanoparticles were loaded on the surface of flyash microspheres (FMS) by ion-exchange method to prepare Ag@AgCl-FMS composite support, then nano-TiO2 thin film was coated on it by hydrolysis precipitation with TiCl4 solution as precursor. After annealing at 500℃ for 2 h, the Ag@AgCl-FMS-TiO2 composite photocatalyst was obtained. Its microstructure, crystalline structure and photocatalytic properties under visible light were characterized. The results show that the TiO2 thin film on the substrate is uniform and complete. After calcining at 500℃, the material contains of 90% anatase phase and 10% rutile. The composite modified by Ag@AgCl nanoparticles exhibits high photocatalytic activity under visible light, which is caused by the surface plasmon resonance effect of Ag@AgCl. The degradation rate of methyl orange solution can reach 99% after 80 min irradiation under 250 W metal halide lamp. The photocatalyst also shows great stability. Repeated experiments show that the degradation rate of methyl orange solution can still reach 85% after 5 times of using.%采用离子交换法在粉煤灰微珠(FMS)表面沉积Ag@AgCl纳米颗粒,制备Ag@AgCl-FMS复合基底,采用水解-沉淀工艺,以TiCl4为钛源在复合基底表面再包覆纳米TiO2薄膜,经500℃煅烧2h后得到Ag@AgCl- FMS-TiO2复合光催化剂.对材料微观形貌、晶体结构、可见光光催化性能进行了表征与测试.结果表明,复合基底表面包覆的TiO2薄膜均匀完整.500℃煅烧后的物相为90%锐钛矿型TiO2和10%金红石型TiO2.复合催化剂料在Ag@AgCl等离子共振效应的作用下,表现出明显的可见光响应,经可见光照射80 min后对甲基橙的降解率达99%,5次重复使用对甲基橙的降解率保持在85%.