Hierarchical Heterostructures of NiCo2O4@XMoO4 (X = Ni, Co) as an Electrode Material for High-Performance Supercapacitors.

Science.gov (United States)

Hu, Jiyu; Qian, Feng; Song, Guosheng; Wang, Linlin

2016-12-01

Hierarchical heterostructures of NiCo2O4@XMoO4 (X = Ni, Co) were developed as an electrode material for supercapacitor with improved pseudocapacitive performance. Within these hierarchical heterostructures, the mesoporous NiCo2O4 nanosheet arrays directly grown on the Ni foam can not only act as an excellent pseudocapacitive material but also serve as a hierarchical scaffold for growing NiMoO4 or CoMoO4 electroactive materials (nanosheets). The electrode made of NiCo2O4@NiMoO4 presented a highest areal capacitance of 3.74 F/cm(2) at 2 mA/cm(2), which was much higher than the electrodes made of NiCo2O4@CoMoO4 (2.452 F/cm(2)) and NiCo2O4 (0.456 F/cm(2)), respectively. Meanwhile, the NiCo2O4@NiMoO4 electrode exhibited good rate capability. It suggested the potential of the hierarchical heterostructures of NiCo2O4@CoMoO4 as an electrode material in supercapacitors.

Hierarchical CaCO3 chromatography: a stationary phase based on biominerals.

Science.gov (United States)

Sato, Kosuke; Oaki, Yuya; Takahashi, Daisuke; Toshima, Kazunobu; Imai, Hiroaki

2015-03-23

In biomineralization, acidic macromolecules play important roles for the growth control of crystals through a specific interaction. Inspired by this interaction, we report on an application of the hierarchical structures in CaCO3 biominerals to a stationary phase of chromatography. The separation and purification of acidic small organic molecules are achieved by thin-layer chromatography and flash chromatography using the powder of biominerals as the stationary phase. The unit nanocrystals and their oriented assembly, the hierarchical structure, are suitable for the adsorption site of the target organic molecules and the flow path of the elution solvents, respectively. The separation mode is ascribed to the specific adsorption of the acidic molecules on the crystal face and the coordination of the functional groups to the calcium ions. The results imply that a new family of stationary phase of chromatography can be developed by the fine tuning of hierarchical structures in CaCO3 materials. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Three-dimensional hierarchical NiCo2O4 nanowire@Ni3S2 nanosheet core/shell arrays for flexible asymmetric supercapacitors

Science.gov (United States)

Liu, Bo; Kong, Dezhi; Huang, Zhi Xiang; Mo, Runwei; Wang, Ye; Han, Zhaojun; Cheng, Chuanwei; Yang, Hui Ying

2016-05-01

Three-dimensional (3D) hierarchical NiCo2O4@Ni3S2 core/shell arrays on Ni foam were synthesized by a facile, stepwise synthesis approach. The 3D heterogeneous NiCo2O4 nanostructure forms an interconnected web-like scaffold and serves as the core for the Ni3S2 shell. The as-prepared NiCo2O4@Ni3S2 nanowire array (NWA) electrodes exhibited excellent electrochemical performance, such as high specific areal capacitance and excellent cycling stability. The specific areal capacitance of 3.0 F cm-2 at a current density of 5 mA cm-2 is among the highest values and the only 6.7% capacitance decay after 10 000 cycles demonstrates the excellent cycling stability. A flexible asymmetric supercapacitor (ASC) was fabricated with activated carbon (AC) as the anode and the obtained NiCo2O4@Ni3S2 NWAs as the cathode. The ASC device exhibited a high energy density of 1.89 mW h cm-3 at 5.81 W cm-3 and a high power density of 56.33 W cm-3 at 0.94 mW h cm-3. As a result, the hybrid nanoarchitecture opens a new way to design high performance electrodes for electrochemical energy storage applications.Three-dimensional (3D) hierarchical NiCo2O4@Ni3S2 core/shell arrays on Ni foam were synthesized by a facile, stepwise synthesis approach. The 3D heterogeneous NiCo2O4 nanostructure forms an interconnected web-like scaffold and serves as the core for the Ni3S2 shell. The as-prepared NiCo2O4@Ni3S2 nanowire array (NWA) electrodes exhibited excellent electrochemical performance, such as high specific areal capacitance and excellent cycling stability. The specific areal capacitance of 3.0 F cm-2 at a current density of 5 mA cm-2 is among the highest values and the only 6.7% capacitance decay after 10 000 cycles demonstrates the excellent cycling stability. A flexible asymmetric supercapacitor (ASC) was fabricated with activated carbon (AC) as the anode and the obtained NiCo2O4@Ni3S2 NWAs as the cathode. The ASC device exhibited a high energy density of 1.89 mW h cm-3 at 5.81 W cm-3 and a high power

Biofuel Production from Jatropha Bio-Oil Derived Fast Pyrolysis: Effect and Mechanism of CoMoS Supported on Al2O3

Science.gov (United States)

Rodseanglung, T.; Ratana, T.; Phongaksorn, M.; Tungkamani, S.

2018-03-01

The aims of this research was to understand the CoMo/Al2O3 sulfide catalyst effect to remove oxygen-containing and nitrogen-containing molecules from Jatropha bio-oil derived fast pyrolysis converted to biofuels via hydrotreating process. The activity and selectivity of CoMo/γ-Al2O3 sulfided catalysts in hydrodeoxygenation (HDO) of Jatropha bio-oil derived fast pyrolysis was evaluated in a Parr batch reactor under 50 bar of H2 atmosphere for 2 h at 300 320 and 340 °C. It appeared that the CoMo/Al2O3 sulfide catalyst have high performance in activity for promoting the fatty acid, fatty ester, fatty amide and fatty nitrile compounds were converted to paraffin/olefin (Diesel range), this could be the CUS site on supported Al2O3 catalyst. The difference in selectivity products allowed us to propose a reaction scheme.

Preparation and characterization of composites based on PBAT/Starch blend, micro and nanofillers of bio-CaCO{sub 3}; Preparacao e caracterizacao de compositos baseados na blenda de PBAT/amido, micro e nanocargas de bio-CaCo{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Silva, Valquiria A.; Neto, Jose C. de M.; Moura, Esperidiana A.B. [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN/SP), Sao Paulo, SP (Brazil); Tiimob, Boniface; Rangari, Vijaya K. [Department of Materials Science and Engineering, Tuskegee University, Tuskegee, AL (United States); Silva, Raimundo N.A. da, E-mail: jmacedo@uea.edu.br [Universidade do Estado do Amazonas (UEA), Manaus, AM (Brazil). Escola Superior de Tecnologia. Coordenacao de Engenharia de Materiais

2015-07-01

Biodegradable polymeric materials have been used as an alternative to synthetic polymeric materials due to their reduced environmental impact. Among the biodegradable polymers is investigated poly (butylene adipate-co-terephthalate) (PBAT). This polymer has the flexibility, high strain at break and easy processing, but a high cost and low toughness that limits their applications. The development of PBAT blends with thermoplastic starch or other biodegradable polymers may lead to a balance of properties, expand its range of applications and also make it more economically viable. The mechanical properties of biodegradable PBAT blends may be further improved by incorporating micro or nanofillers from renewable sources. This study aimed to the processing and characterization of a PBAT/Starch blend reinforced with 2% (wt.) of bioCaCO{sub 3} nanoparticles (nano-bioCaCO{sub 3}) and 5% (wt.) of bioCaCO{sub 3}-micro (particles ≤ 125 μm). For the preparations were used a co-rotating twin-screw extruder. For the characterization of the prepared materials were used X-ray diffraction (XRD) and tensile test. The XRD results showed the greatest intensity peak of CaCO{sub 3} in the matrix for composites containing bio-CaCO{sub 3} nanofillers suggesting a better interaction between matrix and nanofillers. The results of the tensile test confirmed the better interaction between matrix and nanofillers. These results showed that the addition of only 2 % (wt.) of bio-CaCO{sub 3} nanoparticles in PBAT/Starch blend led to obtaining a tougher material with improved tensile strength and elastic modulus properties regarding the polymer blend. (author)

Upgrading pyrolysis bio-oil through hydrodeoxygenation (HDO) using non-sulfided Fe-Co/SiO2 catalyst

International Nuclear Information System (INIS)

Cheng, Shouyun; Wei, Lin; Julson, James; Rabnawaz, Muhammad

2017-01-01

Highlights: • Fe-Co/SiO 2 catalyst with medium acidity was more effective for bio-oil upgrading. • Co-loading of Fe and Co on SiO 2 support improved catalyst performance. • Catalyst showing the best catalytic activity had a Fe/Co mole ratio of 1. • Biofuel produced by Fe-Co(1)/SiO 2 had the higher hydrocarbons content at 22.44%. • The mechanism of bio-oil HDO on Fe-Co/SiO 2 catalysts is proposed. - Abstract: Hydrodeoxygenation (HDO) is an effective route to upgrade bio-oil to hydrocarbon bio-oil, but the development of efficient catalysts for bio-oil HDO still remains a challenge. In this study, non-sulfided Fe-Co/SiO 2 catalysts were used to upgrade bio-oil using HDO. A series of Fe-Co/SiO 2 catalysts with different Fe/Co mole ratios were prepared, characterized and evaluated. The Fe and/or Co loading did not change SiO 2 crystalline structure. The Fe and/or Co metals increased the amount and strength of Fe-Co/SiO 2 catalyst acidity. Physicochemical properties of upgraded bio-oils produced using Fe-Co/SiO 2 catalysts such as water content, total acid number, viscosity and higher heating values improved in comparison to raw bio-oil. Bimetallic Fe-Co/SiO 2 catalysts resulted in better HDO performance than monometallic Fe/SiO 2 or Co/SiO 2 catalysts. This was due to the synergistic effect of Fe and Co occurring on the SiO 2 support. Fe-Co/SiO 2 catalyst having medium amount of acidity was more effective for bio-oil upgrading. The highest hydrocarbons content produced using Fe-Co(1)/SiO 2 catalyst was 22.44%. The mechanism of bio-oil HDO on Fe-Co/SiO 2 catalysts is proposed.

Self-assembled hierarchical direct Z-scheme g-C3N4/ZnO microspheres with enhanced photocatalytic CO2 reduction performance

Science.gov (United States)

Nie, Ning; Zhang, Liuyang; Fu, Junwei; Cheng, Bei; Yu, Jiaguo

2018-05-01

Photocatalytic reduction of CO2 into hydrocarbon fuels has been regarded as a promising approach to ease the greenhouse effect and the energy shortage. Herein, an electrostatic self-assembly method was exploited to prepare g-C3N4/ZnO composite microsphere. This method simply utilized the opposite surface charge of each component, achieving a hierarchical structure with intimate contact between them. A much improved photocatalytic CO2 reduction activity was attained. The CH3OH production rate was 1.32 μmol h-1 g-1, which was 2.1 and 4.1 times more than that of the pristine ZnO and g-C3N4, respectively. This facile design bestowed the g-C3N4/ZnO composite an extended light adsorption caused by multi-light scattering effect. It also guaranteed the uniform distribution of g-C3N4 nanosheets on the surface of ZnO microspheres, maximizing their advantage and synergistic effect. Most importantly, the preeminent performance was proposed and validated based on the direct Z-scheme. The recombination rate was considerably suppressed. This work features the meliority of constructing hierarchical direct Z-scheme structures in photocatalytic CO2 reduction reactions.

Bio-template-assisted synthesis of hierarchically hollow SiO2 microtubes and their enhanced formaldehyde adsorption performance

International Nuclear Information System (INIS)

Le, Yao; Guo, Daipeng; Cheng, Bei; Yu, Jiaguo

2013-01-01

The indoor air quality is crucial for human health, taking into account that people often spend more than 80% of their time in houses, offices and cars. Formaldehyde (HCHO) is a major pollutant and long-term exposure to HCHO may cause health problems such as nasal tumors and skin irritation. In this work, for the first time, hierarchically hollow silica microtubes (HHSM) were synthesized by a simple sol–gel and calcination method using cetyltrimethyl ammonium bromide (CTAB) and bio-template poplar catkin (PC) as co-templates and the PC/SiO 2 weight ratio R was varied from 0, 0.1, 0.3 and 1. The prepared samples were further modified with tetraethylenepentamine (TEPA) and characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), differential thermal analysis (DTA), thermal gravimetric analysis (TGA), and N 2 physisorption techniques. This was followed by formaldehyde adsorption tests at ambient temperature. The results showed that all the prepared HHSM samples contained small mesopores with peak pore size at ca. 2.5 nm and large several tens of nanometer-sized pores on the tube wall. The R exhibited an obvious influence on specific surface areas and the sample prepared at R = 0.3 exhibited highest specific surface area (896 m 2 /g). All the TEPA-modified samples exhibited enhanced formaldehyde adsorption performance. The maximum HCHO adsorption capacity (20.65 mg/g adsorbent) was achieved on the sample prepared at R = 0.3 and modified by 50 wt.% TEPA. The present study will provide new insight for the utilization of bio-template used for the fabrication of inorganic hollow tubes with high HCHO adsorption performance for indoor air purification.

Two-step growth mechanism of supported Co3O4-based sea-urchin like hierarchical nanostructures

Science.gov (United States)

Maurizio, Chiara; Edla, Raju; Michieli, Niccolo'; Orlandi, Michele; Trapananti, Angela; Mattei, Giovanni; Miotello, Antonio

2018-05-01

Supported 3D hierarchical nanostructures of transition metal oxides exhibit enhanced photocatalytic performances and long-term stability under working conditions. The growth mechanisms crucially determine their intimate structure, that is a key element to optimize their properties. We report on the formation mechanism of supported Co3O4 hierarchical sea urchin-like nanostructured catalyst, starting from Co-O-B layers deposited by Pulsed Laser Deposition (PLD). The particles deposited on the layer surface, that constitute the seeds for the urchin formation, have been investigated after separation from the underneath deposited layer, by X-ray diffraction, X-ray absorption spectroscopy and scanning electron microscopy. The comparison with PLD deposited layers without O and/or B indicates a crucial role of B for the urchin formation that (i) limits Co oxidation during the deposition process and (ii) induces a chemical reduction of Co, especially in the particle core, in the first step of air annealing (2 h, 500 °C). After 2 h heating Co oxidation proceeds and Co atoms outdiffuse from the Co fcc particle core likely through fast diffusion channel present in the shell and form Co3O4 nano-needles. The growth of nano-needles from the layer beneath the particles is prevented by a faster Co oxidation and a minimum fraction of metallic Co. This investigation shows how diffusion mechanisms and chemical effects can be effectively coupled to obtain hierarchical structures of transition metal oxides.

Self-assembly of monodisperse starburst carbon spheres into hierarchically organized nanostructured supercapacitor electrodes.

Science.gov (United States)

Kim, Sung-Kon; Jung, Euiyeon; Goodman, Matthew D; Schweizer, Kenneth S; Tatsuda, Narihito; Yano, Kazuhisa; Braun, Paul V

2015-05-06

We report a three-dimensional (3D) porous carbon electrode containing both nanoscale and microscale porosity, which has been hierarchically organized to provide efficient ion and electron transport. The electrode organization is provided via the colloidal self-assembly of monodisperse starburst carbon spheres (MSCSs). The periodic close-packing of the MSCSs provides continuous pores inside the 3D structure that facilitate ion and electron transport (electrode electrical conductivity ∼0.35 S m(-1)), and the internal meso- and micropores of the MSCS provide a good specific capacitance. The capacitance of the 3D-ordered porous MSCS electrode is ∼58 F g(-1) at 0.58 A g(-1), 48% larger than that of disordered MSCS electrode at the same rate. At 1 A g(-1) the capacitance of the ordered electrode is 57 F g(-1) (95% of the 0.24 A g(-1) value), which is 64% greater than the capacitance of the disordered electrode at the same rate. The ordered electrode preserves 95% of its initial capacitance after 4000 charging/discharging cycles.

Nanoparticle Decorated Ultrathin Porous Nanosheets as Hierarchical Co3O4 Nanostructures for Lithium Ion Battery Anode Materials

Science.gov (United States)

Mujtaba, Jawayria; Sun, Hongyu; Huang, Guoyong; Mølhave, Kristian; Liu, Yanguo; Zhao, Yanyan; Wang, Xun; Xu, Shengming; Zhu, Jing

2016-01-01

We report a facile synthesis of a novel cobalt oxide (Co3O4) hierarchical nanostructure, in which crystalline core-amorphous shell Co3O4 nanoparticles with a bimodal size distribution are uniformly dispersed on ultrathin Co3O4 nanosheets. When tested as anode materials for lithium ion batteries, the as-prepared Co3O4 hierarchical electrodes delivered high lithium storage properties comparing to the other Co3O4 nanostructures, including a high reversible capacity of 1053.1 mAhg−1 after 50 cycles at a current density of 0.2 C (1 C = 890 mAg−1), good cycling stability and rate capability. PMID:26846434

Preparation and characterization of composites based on PBAT/Starch blend, micro and nanofillers of bio-CaCO_3

International Nuclear Information System (INIS)

Silva, Valquiria A.; Neto, Jose C. de M.; Moura, Esperidiana A.B.; Tiimob, Boniface; Rangari, Vijaya K.; Silva, Raimundo N.A. da

2015-01-01

Biodegradable polymeric materials have been used as an alternative to synthetic polymeric materials due to their reduced environmental impact. Among the biodegradable polymers is investigated poly (butylene adipate-co-terephthalate) (PBAT). This polymer has the flexibility, high strain at break and easy processing, but a high cost and low toughness that limits their applications. The development of PBAT blends with thermoplastic starch or other biodegradable polymers may lead to a balance of properties, expand its range of applications and also make it more economically viable. The mechanical properties of biodegradable PBAT blends may be further improved by incorporating micro or nanofillers from renewable sources. This study aimed to the processing and characterization of a PBAT/Starch blend reinforced with 2% (wt.) of bioCaCO_3 nanoparticles (nano-bioCaCO_3) and 5% (wt.) of bioCaCO_3-micro (particles ≤ 125 μm). For the preparations were used a co-rotating twin-screw extruder. For the characterization of the prepared materials were used X-ray diffraction (XRD) and tensile test. The XRD results showed the greatest intensity peak of CaCO_3 in the matrix for composites containing bio-CaCO_3 nanofillers suggesting a better interaction between matrix and nanofillers. The results of the tensile test confirmed the better interaction between matrix and nanofillers. These results showed that the addition of only 2 % (wt.) of bio-CaCO_3 nanoparticles in PBAT/Starch blend led to obtaining a tougher material with improved tensile strength and elastic modulus properties regarding the polymer blend. (author)

Carbon Dioxide (CO2 Sequestration In Bio-Concrete, An Overview

Directory of Open Access Journals (Sweden)

Faisal Alshalif A.

2017-01-01

Full Text Available The emission of CO2 into atmosphere which has increased rapidly in the last years has led to global warming. Therefore, in order to overcome the negative impacts on human and environment, the researchers focused mainly on the reduction and stabilization of CO2 which represent the main contributor in the increasing global warming. The natural capturing and conversion of CO2 from atmosphere is taken place by biological, chemical and physical processes. However, these processes need long time to cause a significant reduction in CO2. Recently, scientists shifted to use green technologies that aimed to produce concrete with high potential to adsorb CO2 in order to accelerate the reduction of CO2. In the present review the potential of bio-concrete to sequestrate CO2 based on carbonation process and as a function of carbonic anhydrase (CA is highlighted. The factors affecting CO2 sequestration in concrete and bacterial species are discussed. It is evident from the literatures, that the new trends to use bio-concrete might contribute in the reduction of CO2 and enhance the strength of non-reinforced concrete.

Final Report for Fractionation and Separation of Polydisperse Nanoparticles into Distinct Monodisperse Fractions Using CO2 Expanded Liquids

Energy Technology Data Exchange (ETDEWEB)

Chistopher Roberts

2007-08-31

The overall objective of this project was to facilitate efficient fractionation and separation of polydisperse metal nanoparticle populations into distinct monodisperse fractions using the tunable solvent properties of gas expanded liquids. Specifically, the dispersibility of ligand-stabilized nanoparticles in an organic solution was controlled by altering the ligand-solvent interaction (solvation) by the addition of carbon dioxide (CO{sub 2}) gas as an antisolvent (thereby tailoring the bulk solvent strength) in a custom high pressure apparatus developed in our lab. This was accomplished by adjusting the CO{sub 2} pressure over the liquid dispersion, resulting in a simple means of tuning the nanoparticle precipitation by size. Overall, this work utilized the highly tunable solvent properties of organic/CO{sub 2} solvent mixtures to selectively size-separate dispersions of polydisperse nanoparticles (ranging from 1 to 20 nm in size) into monodisperse fractions ({+-}1nm). Specifically, three primary tasks were performed to meet the overall objective. Task 1 involved the investigation of the effects of various operating parameters (such as temperature, pressure, ligand length and ligand type) on the efficiency of separation and fractionation of Ag nanoparticles. In addition, a thermodynamic interaction energy model was developed to predict the dispersibility of different sized nanoparticles in the gas expanded liquids at various conditions. Task 2 involved the extension of the experimental procedures identified in task 1 to the separation of other metal particles used in catalysis such as Au as well as other materials such as semiconductor particles (e.g. CdSe). Task 3 involved using the optimal conditions identified in tasks 1 and 2 to scale up the process to handle sample sizes of greater than 1 g. An experimental system was designed to allow nanoparticles of increasingly smaller sizes to be precipitated sequentially in a vertical series of high pressure vessels by

Assembly of Fe3O4 nanoparticles on SiO2 monodisperse spheres

Indian Academy of Sciences (India)

Assembly of Fe3O4 nanoparticles on SiO2 monodisperse spheres. K C BARICK and D BAHADUR*. Department of Metallurgical Engineering and Materials Science, Indian Institute of Technology Bombay,. Mumbai 400 076, India. Abstract. The assembly of superparamagnetic Fe3O4 nanoparticles on submicroscopic SiO2 ...

A co-flow-focusing monodisperse microbubble generator

KAUST Repository

Zhang, Jiaming; Li, Erqiang; Thoroddsen, Sigurdur T

2014-01-01

We use a simple and inexpensive microfluidic device, which is based on microscope glass slides and two tapered glass capillaries, to produce monodisperse microbubbles. The innermost capillary used for transporting the gas is inserted into the second capillary, with its 2 μm sharp tip aligned with the center of the converging-diverging throat of the second capillary. This configuration provides a small and smooth gas flow rate, and a high velocity gradient at the tube outlet. Highly monodisperse microbubbles with diameters ranging from 3.5 to 60 microns have been successfully produced at a rate of up to 40 kHz. A simple scaling law, which is based on the capillary number and liquid-to-gas flow rate ratio, successfully predicts the bubble size. © 2014 IOP Publishing Ltd.

A co-flow-focusing monodisperse microbubble generator

KAUST Repository

Zhang, Jiaming

2014-02-14

We use a simple and inexpensive microfluidic device, which is based on microscope glass slides and two tapered glass capillaries, to produce monodisperse microbubbles. The innermost capillary used for transporting the gas is inserted into the second capillary, with its 2 μm sharp tip aligned with the center of the converging-diverging throat of the second capillary. This configuration provides a small and smooth gas flow rate, and a high velocity gradient at the tube outlet. Highly monodisperse microbubbles with diameters ranging from 3.5 to 60 microns have been successfully produced at a rate of up to 40 kHz. A simple scaling law, which is based on the capillary number and liquid-to-gas flow rate ratio, successfully predicts the bubble size. © 2014 IOP Publishing Ltd.

3D hierarchical porous cobalt monoxide nanoplates with a book-like structure derived from Co(CO3)0.5(OH)·0.11H2O: two-steps oriented attachment and high-performance asymmetric supercapacitors

Science.gov (United States)

Xiao, Yuanhua; Zhao, Xiaobing; Jin, Qingxian; Su, Dangcheng; Wang, Xuezhao; Wu, Shide; Zhou, Liming; Fang, Shaoming

2017-10-01

3D Hierarchical porous cobalt monoxide (CoO) nanoplates with a book-like structure derive from Co(CO3)0.5(OH)·0.11H2O by a two-steps oriented attachment mechanism in the solvothermal process. Firstly, nanoplates are formed by oriented attachment of nanorods. Secondly, new nanoplates could be generated on the old nanoplates by a sloped oriented attachment of nanorods with the based nanoplates shape into a 3D hierarchical book-like structure. The CoO nanoplates show superior specific capacitance about 1221.7 F g-1 at 1 A g-1 to most of the Co-based supercapacitor materials up to date. An asymmetric supercapacitor (ASC) based on positive electrode CoO and negative electrode active carbon (AC) exhibits an excellent energy density of 50.1 Wh kg-1 at a power density of 589 W kg-1 and gets a satisfactory cycling stability (86.3% of its initial capacitance retention at 10 A g-1 over 10 000 cycles).

Tunable multicolor and enhanced red emission of monodisperse CaF2:Yb3+/Ho3+ microspheres via Mn2+ doping

Science.gov (United States)

Wang, Rui; Yuan, Maohui; Zhang, Chaofan; Wang, Hongyan; Xu, Xiaojun

2018-05-01

Transition metal ions (e.g. Mn2+) and lanthanide co-doped upconversion (UC) materials have attracted wide attention in recent years due to their promising application in multicolor display. Here, we report the hydrothermal synthesis and characterization of Mn2+ doped monodisperse CaF2:Yb3+/Ho3+ microspheres. The results of X-ray diffraction (XRD) revealed that Mn2+ doping does not change the cubic phase of CaF2 material but will lead to diffraction peaks shifting slightly towards higher angle due to the substitution of larger Ca2+ by the relatively smaller Mn2+. Under the excitation of 980 nm continuous wave (CW) laser, these microspheres exhibit green-yellow-red tuning colors and remarkable enhancement of both red to green ratio (R/G) and red to blue ratio (R/B) when increasing Mn2+ concentration from 0 to 30 mol%. The energy migration process between Ho3+ and Mn2+ was proposed and supported by time-decay and power dependence measurements of Ho3+ UC emission. These upconversion materials may have potential applications in optical devices, color display, nanoscale lasers and biomedical imaging.

Hierarchically porous Ni monolith@branch-structured NiCo2O4 for high energy density supercapacitors

Directory of Open Access Journals (Sweden)

Mengjie Xu

2016-06-01

Full Text Available A variety of NiCo2O4 nanostrucutures ranging from nanowire to nanoplate and branched structures were successfully prepared via a simple hydrothermal process. The experimental results show that NiCo2O4 with branched structures possesses the best overall electrochemical performance. The improvement of energy density was explored in terms of hierarchically three-dimensional (3D metal substrates and a high specific area capacitance, and area energy density is obtained with hierarchically porous Ni monolith synthesized through a controlled combustion procedure.

Co3O4 based non-enzymatic glucose sensor with high sensitivity and reliable stability derived from hollow hierarchical architecture

Science.gov (United States)

Tian, Liangliang; He, Gege; Cai, Yanhua; Wu, Shenping; Su, Yongyao; Yan, Hengqing; Yang, Cong; Chen, Yanling; Li, Lu

2018-02-01

Inspired by kinetics, the design of hollow hierarchical electrocatalysts through large-scale integration of building blocks is recognized as an effective approach to the achievement of superior electrocatalytic performance. In this work, a hollow, hierarchical Co3O4 architecture (Co3O4 HHA) was constructed using a coordinated etching and precipitation (CEP) method followed by calcination. The resulting Co3O4 HHA electrode exhibited excellent electrocatalytic activity in terms of high sensitivity (839.3 μA mM-1 cm-2) and reliable stability in glucose detection. The high sensitivity could be attributed to the large specific surface area (SSA), ample unimpeded penetration diffusion paths and high electron transfer rate originating from the unique two-dimensional (2D) sheet-like character and hollow porous architecture. The hollow hierarchical structure also affords sufficient interspace for accommodation of volume change and structural strain, resulting in enhanced stability. The results indicate that Co3O4 HHA could have potential for application in the design of non-enzymatic glucose sensors, and that the construction of hollow hierarchical architecture provides an efficient way to design highly active, stable electrocatalysts.

Sonochemical synthesis of (3-aminopropyl)triethoxysilane-modified monodispersed silica nanoparticles for protein immobilization

International Nuclear Information System (INIS)

Shen, Shou-Cang; Ng, Wai Kiong; Chia, Leonard; Dong, Yuan-Cai; Tan, Reginald B.H.

2011-01-01

Graphical abstract: 3-Aminopropyltriethoxysilane modified monodispersed silica nanoparticles were synthesized by rapid sonochemical co-condensation to achieve high capability for protein immobilization. Highlights: → Amino-modified monodispersed silica nanoparticles were synthesized by rapid co-condensation. → Strong positive charge was created by aminopropyl-modification. → Capability for immobilization of negatively charged protein was enhanced. → Electrostatic interaction between proteins and surface contributed to the enhanced adsorption. -- Abstract: 3-Aminopropyltriethoxysilane modified monodispersed silica nanoparticles were synthesized by a rapid sonochemical co-condensation synthesis procedure. The chemical nature of surface organic modifier on the obtained modified silica nanoparticle was characterized by 13 C and 29 Si MAS Nuclear Magnetic Resonance (NMR) spectroscopies, Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA)- differential scanning calorimetry (DSC). Due to the strengthened positive surface charge of the silica nanoparticles by the modification with aminopropyl groups, the capability for bovine serum albumin (BSA) adsorption was significantly increased as compared with bare silica nanoparticles. 80 mg/g BSA was adsorbed on modified silica nanoparticles, whereas only 20 mg/g BSA could be loaded on pure silica nanoparticles. The enhanced positive surface charge repelled proteins with net positive charge and the modified silica nanoparticles exhibited negligible adsorption of lysozyme, thus a selective adsorption of proteins could be achieved.

Sonochemical synthesis of (3-aminopropyl)triethoxysilane-modified monodispersed silica nanoparticles for protein immobilization

Energy Technology Data Exchange (ETDEWEB)

Shen, Shou-Cang, E-mail: shen_shoucang@ices.a-star.edu.sg [Institute of Chemical and Engineering Sciences, A-STAR (Agency for Science, Technology and Research), 1 Pesek Road, Jurong Island, Singapore 627833 (Singapore); Ng, Wai Kiong; Chia, Leonard; Dong, Yuan-Cai [Institute of Chemical and Engineering Sciences, A-STAR (Agency for Science, Technology and Research), 1 Pesek Road, Jurong Island, Singapore 627833 (Singapore); Tan, Reginald B.H., E-mail: reginald_tan@ices.a-star.edu.sg [Institute of Chemical and Engineering Sciences, A-STAR (Agency for Science, Technology and Research), 1 Pesek Road, Jurong Island, Singapore 627833 (Singapore); Department of Chemical and Biomolecular Engineering, The National University of Singapore, 4 Engineering Drive 4, Singapore 117576 (Singapore)

2011-10-15

Graphical abstract: 3-Aminopropyltriethoxysilane modified monodispersed silica nanoparticles were synthesized by rapid sonochemical co-condensation to achieve high capability for protein immobilization. Highlights: {yields} Amino-modified monodispersed silica nanoparticles were synthesized by rapid co-condensation. {yields} Strong positive charge was created by aminopropyl-modification. {yields} Capability for immobilization of negatively charged protein was enhanced. {yields} Electrostatic interaction between proteins and surface contributed to the enhanced adsorption. -- Abstract: 3-Aminopropyltriethoxysilane modified monodispersed silica nanoparticles were synthesized by a rapid sonochemical co-condensation synthesis procedure. The chemical nature of surface organic modifier on the obtained modified silica nanoparticle was characterized by {sup 13}C and {sup 29}Si MAS Nuclear Magnetic Resonance (NMR) spectroscopies, Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA)- differential scanning calorimetry (DSC). Due to the strengthened positive surface charge of the silica nanoparticles by the modification with aminopropyl groups, the capability for bovine serum albumin (BSA) adsorption was significantly increased as compared with bare silica nanoparticles. 80 mg/g BSA was adsorbed on modified silica nanoparticles, whereas only 20 mg/g BSA could be loaded on pure silica nanoparticles. The enhanced positive surface charge repelled proteins with net positive charge and the modified silica nanoparticles exhibited negligible adsorption of lysozyme, thus a selective adsorption of proteins could be achieved.

Metal Fe3+ ions assisted synthesis of highly monodisperse Ag/SiO2 nanohybrids and their antibacterial activity

International Nuclear Information System (INIS)

Zhang, Nianchun; Xue, Feng; Yu, Xiang; Zhou, Huihua; Ding, Enyong

2013-01-01

Graphical abstract: TEM images of the Ag/SiO 2 -2 nanohybrids. The homogeneous and more mono-disperse Ag nanoparticles deposit on SiO 2 spheres. Through this method, Ag nanoparticles are easily formed on the surface of SiO 2 compared to other methods. Highlights: ► We prepared homogeneous and mono-dispersed Ag/SiO 2 -2 nanohybrids by adding Fe 3+ ions. ► The Ag/SiO 2 -2 nanohybrids had core(SiO 2 )-shell(Ag) structure. ► The Ag/SiO 2 -2 nanohybrids exhibited excellent antibacterial activity against bacteria. ► The reaction temperature was lower and the yield of Ag/SiO 2 -2 nanohybrids were higher. - Abstract: Highly monodispersed Ag/SiO 2 nanohybrids with excellent antibacterial property were synthesized by using DMF as a reducing agent and employing an additional redox potential of metal Fe 3+ ion as a catalytic agent. The obtained Ag/SiO 2 -2 nanohybrids of about 240 nm were highly monodispersity and uniformity by adding trace Fe 3+ ions into the reaction which Ag + reacted with N,N-dimethyl formamide (DMF) at 70 °C. Compared to the conventional techniques, which need long time and high temperature for silica coating of Ag nanoparticles, this new method was capable of synthesizing monodispersed, uniform, high yield Ag/SiO 2 nanohybrids. The electron was transferred from the Fe 2+ ion to the Ag + ion to accelerate the nucleation of silver nanoparticles. The chemical structures, morphologies and properties of the Ag/SiO 2 nanohybrids were characterized by X-ray diffraction (XRD), (High-resolution, Scanning transmission) transmission electron microscopy (TEM, HRTEM and STEM), and X-ray photoelectron spectroscopy (XPS), and UV–vis spectroscopy (UV–vis) and test of antibacterial. The results demonstrated that the silver nanoparticles supported on the surface of SiO 2 spheres in Ag/SiO 2 -2 nanohybrids structure, the Ag nanoparticles were homogeneous and monodispersed. The results also indicated that the Ag/SiO 2 -2 nanohybrid had excellent antibacterial.

Rational construction of a 3D hierarchical NiCo2O4/PANI/MF composite foam as a high-performance electrode for asymmetric supercapacitors.

Science.gov (United States)

Cui, Fen; Huang, Yunpeng; Xu, Le; Zhao, Yan; Lian, Jiabiao; Bao, Jian; Li, Huaming

2018-04-19

A 3D hierarchical NiCo2O4/PANI/MF composite foam with a macroporous 3D skeleton, a conductive PANI coating and highly electrochemically active NiCo2O4 nanosheets is synthesized as a lightweight and low-cost electrode material. Due to the collaborative contribution of all the components, the prepared composite foam exhibits excellent capacitive performances when incorporated into an asymmetric supercapacitor.

Three-Dimensional Hierarchical NixCo1-xO/NiyCo2-yP@C Hybrids on Nickel Foam for Excellent Supercapacitors.

Science.gov (United States)

Shao, Yubo; Zhao, Yongqing; Li, Hua; Xu, Cailing

2016-12-28

Active materials and special structures of the electrode have decisive influence on the electrochemical properties of supercapacitors. Herein, three-dimensional (3D) hierarchical Ni x Co 1-x O/Ni y Co 2-y P@C (denoted as NiCoOP@C) hybrids have been successfully prepared by a phosphorization treatment of hierarchical Ni x Co 1-x O@C grown on nickel foam. The resulting NiCoOP@C hybrids exhibit an outstanding specific capacitance and cycle performance because they couple the merits of the superior cycling stability of Ni x Co 1-x O, the high specific capacitance of Ni y Co 2-y P, the mechanical stability of carbon layer, and the 3D hierarchical structure. The specific capacitance of 2638 F g -1 can be obtained at the current density of 1 A g -1 , and even at the current density of 20 A g -1 , the NiCoOP@C electrode still possesses a specific capacitance of 1144 F g -1 . After 3000 cycles at 10 A g -1 , 84% of the initial specific capacitance is still remained. In addition, an asymmetric ultracapacitor (ASC) is assembled through using NiCoOP@C hybrids as anode and activated carbon as cathode. The as-prepared ASC obtains a maximum energy density of 39.4 Wh kg -1 at a power density of 394 W kg -1 and still holds 21 Wh kg -1 at 7500 W kg -1 .

Hierarchically porous MgCo2O4 nanochain networks: template-free synthesis and catalytic application

Science.gov (United States)

Guan, Xiangfeng; Yu, Yunlong; Li, Xiaoyan; Chen, Dagui; Luo, Peihui; Zhang, Yu; Guo, Shanxin

2018-01-01

In this work, hierarchically porous MgCo2O4 nanochain networks were successfully synthesized by a novel template-free method realized via a facile solvothermal synthesis followed by a heat treatment. The morphologies of MgCo2O4 precursor could be adjusted from nanosheets to nanobelts and finally to interwoven nanowires, depending on the volume ratio of diethylene glycol to deionized water in the solution. After calcination, the interwoven precursor nanowires were transformed to hierarchical MgCo2O4 nanochain networks with marco-/meso-porosity, which are composed of 10-20 nm nanoparticles connected one by one. Moreover, the relative formation mechanism of the MgCo2O4 nanochain networks was discussed. More importantly, when evaluated as catalytic additive for AP thermal decomposition, the MgCo2O4 nanochain networks show excellent accelerating effect. It is benefited from the unique hierarchically porous network structure and multicomponent effect, which effectively accelerates ammonia oxidation and {{{{ClO}}}4}- species dissociation. This approach opens the way to design other hierarchically porous multicomponent metal oxides.

Monodispersed ZIF-8 particles with enhanced performance for CO2 adsorption and heterogeneous catalysis

Science.gov (United States)

Guan, Yebin; Shi, Juanjuan; Xia, Ming; Zhang, Jun; Pang, Zhenfeng; Marchetti, Alessandro; Wang, Xiaohong; Cai, Jingsong; Kong, Xueqian

2017-11-01

Monodispersed zeolitic imidazolate frameworks (ZIFs) were prepared with a simple method using dimethylsulfoxide (DMSO) as solvent. This method yields ZIF-8 nanoparticles with a narrow particle size distribution of 90-110 nm and the dispersion is highly stable against agglomeration. These particles have larger nanosized porosity and enhanced CO2 adsorption capability compared to ZIF-8 prepared with different solvents such as methanol or N, N-dimethyl formamide. Their uniform size and surface chemistry also lead to superior performance in the Knoevenagel condensation reactions. The ZIF-8 nanoparticles possess high thermal stability up to 550 °C and the preparation steps are easy for scaling up which are favorable for industrial applications.

Synthesis of hierarchical ZnV2O6 nanosheets with enhanced activity and stability for visible light driven CO2 reduction to solar fuels

Science.gov (United States)

Bafaqeer, Abdullah; Tahir, Muhammad; Amin, Nor Aishah Saidina

2018-03-01

Hierarchical nanostructures have lately garnered enormous attention because of their remarkable performances in energy storage and catalysis applications. In this study, novel hierarchical ZnV2O6 nanosheets, formulated by one-step solvothermal method, for enhanced photocatalytic CO2 reduction with H2O to solar fuels has been investigated. The structure and properties of the catalysts were characterized by XRD, FESEM, TEM, BET, UV-vis, Raman and PL spectroscopy. The hierarchical ZnV2O6 nanosheets show excellent performance towards photoreduction of CO2 with H2O to CH3OH, CH3COOH and HCOOH under visible light. The main product yield, CH3OH of 3253.84 μmol g-cat-1 was obtained over ZnV2O6, 3.4 times the amount of CH3OH produced over the ZnO/V2O5 composite (945.28 μmol g-cat-1). In addition, CH3OH selectivity of 39.96% achieved over ZnO/V2O5, increased to 48.78% in ZnV2O6 nanosheets. This significant improvement in photo-activity over ZnV2O6 structure was due to hierarchical structure with enhanced charge separation by V2O5. The obtained ZnV2O6 hierarchical nanosheets exhibited excellent photocatalytic stability for selective CH3OH production.

Monodisperse MnO2@NiCo2O4 core/shell nanospheres with highly opened structures as electrode materials for good-performance supercapacitors

Science.gov (United States)

Zhou, You; Ma, Li; Gan, Mengyu; Ye, Menghan; Li, Xiurong; Zhai, Yanfang; Yan, Fabing; Cao, Feifei

2018-06-01

The monodisperse MnO2@NiCo2O4 core/shell nanospheres for good-performance supercapacitors are designed and synthesized by a two-step solution-based method and a simple post annealing process. In the composite, both MnO2 (the "core") and NiCo2O4 (the "shell") are formed by the accumulation of nanoflakes. Thus, nearly all the core/shell nanoflakes are highly opened and accessible to electrolyte, making them give full play to the Faradaic reaction. Our results demonstrate that the composite electrode exhibits desirable pseudocapacitive behaviors with higher specific capacitance (1127.27 F g-1 at a current density of 1 A g-1), better rate capability (81.0% from 1 to 16 A g-1) and superior cycling stability (actually 126.8% capacitance retention after 1000 cycles and only 3.7% loss after 10,000 cycles at 10 A g-1) in 3 M KOH aqueous solution. Moreover, it offers the excellent specific energy density of 26.6 Wh kg-1 at specific power density of 800 W kg-1. The present MnO2@NiCo2O4 core/shell nanospheres with remarkable electrochemical properties are considered as potential electrode materials for the next generation supercapacitors.

Facile synthesis of hierarchical Co3O4@MnO2 core-shell arrays on Ni foam for asymmetric supercapacitors

Science.gov (United States)

Huang, Ming; Zhang, Yuxin; Li, Fei; Zhang, Lili; Wen, Zhiyu; Liu, Qing

2014-04-01

Hierarchical Co3O4@MnO2 core-shell arrays on Ni foam have been fabricated by a facile hydrothermal approach and further investigated as the electrode for high-performance supercapacitors. Owing to the high conductivity of the well-defined mesoporous Co3O4 nanowire arrays in combination with the large surface area provided by the ultrathin MnO2 nanosheets, the unique designed Co3O4@MnO2 core-shell arrays on Ni foam have exhibited a high specific capacitance (560 F g-1 at a current density of 0.2 A g-1), good rate capability, and excellent cycling stability (95% capacitance retention after 5000 cycles). An asymmetric supercapacitor with Co3O4@MnO2 core-shell nanostructure as the positive electrode and activated microwave exfoliated graphite oxide activated graphene (MEGO) as the negative electrode yielded an energy density of 17.7 Wh kg-1 and a maximum power density of 158 kW kg-1. The rational design of the unique core-shell array architectures demonstrated in this work provides a new and facile approach to fabricate high-performance electrode for supercapacitors.

Stepwise Splitting Growth and Pseudocapacitive Properties of Hierarchical Three-Dimensional Co3O4 Nanobooks

Directory of Open Access Journals (Sweden)

Huilong Chen

2017-04-01

Full Text Available Three-dimensional hierarchical Co3O4 nanobooks have been synthesized successfully on a large scale by calcining orthorhombic Co(CO30.5(OH·0.11H2O precursors with identical morphologies. Based on the influence of reaction time and urea concentration on the nanostructures of the precursors, a stepwise splitting growth mechanism can be proposed to understand the formation of the 3D nanobooks. The 3D Co3O4 nanobooks exhibit excellent pseudocapacitive performances with specific capacitances of 590, 539, 476, 453, and 421 F/g at current densities of 0.5, 1, 2, 4, and 8 A/g, respectively. The devices can retain ca. 97.4% of the original specific capacitances after undergoing charge–discharge cycle tests 1000 times continuously at 4 A/g.

Bio-oil steam reforming, partial oxidation or oxidative steam reforming coupled with bio-oil dry reforming to eliminate CO{sub 2} emission

Energy Technology Data Exchange (ETDEWEB)

Hu, Xun [State Key Laboratory for Oxo Synthesis and Selective Oxidation, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Graduate School of Chinese Academy of Sciences, Beijing 100039 (China); Lu, Gongxuan [State Key Laboratory for Oxo Synthesis and Selective Oxidation, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)

2010-07-15

Biomass is carbon-neutral and utilization of biomass as hydrogen resource shows no impact on atmospheric CO{sub 2} level. Nevertheless, a significant amount of CO{sub 2} is always produced in biomass gasification processes. If the CO{sub 2} produced can further react with biomass, then the biomass gasification coupled with CO{sub 2} reforming of biomass will result in a net decrease of CO{sub 2} level in atmosphere and produce the chemical raw material, syngas. To achieve this concept, a ''Y'' type reactor is developed and applied in bio-oil steam reforming, partial oxidation, or oxidative steam reforming coupled with CO{sub 2} reforming of bio-oil to eliminate the emission of CO{sub 2}. The experimental results show that the reaction systems can efficiently suppress the emission of CO{sub 2} from various reforming processes. The different coupled reaction systems generate the syngas with different molar ratio of CO/H{sub 2}. In addition, coke deposition is encountered in the different reforming processes. Both catalysts and experimental parameters significantly affect the coke deposition. Ni/La{sub 2}O{sub 3} catalyst shows much higher resistivity toward coke deposition than Ni/Al{sub 2}O{sub 3} catalyst, while employing high reaction temperature is vital for elimination of coke deposition. Although the different coupled reaction systems show different characteristic in terms of product distribution and coke deposition, which all can serve as methods for storage of the carbon from fossil fuels or air. (author)

A bio-inspired N-doped porous carbon electrocatalyst with hierarchical superstructure for efficient oxygen reduction reaction

Science.gov (United States)

Miao, Yue-E.; Yan, Jiajie; Ouyang, Yue; Lu, Hengyi; Lai, Feili; Wu, Yue; Liu, Tianxi

2018-06-01

The bio-inspired hierarchical "grape cluster" superstructure provides an effective integration of one-dimensional carbon nanofibers (CNF) with isolated carbonaceous nanoparticles into three-dimensional (3D) conductive frameworks for efficient electron and mass transfer. Herein, a 3D N-doped porous carbon electrocatalyst consisting of carbon nanofibers with grape-like N-doped hollow carbon particles (CNF@NC) has been prepared through a simple electrospinning strategy combined with in-situ growth and carbonization processes. Such a bio-inspired hierarchically organized conductive network largely facilitates both the mass diffusion and electron transfer during the oxygen reduction reactions (ORR). Therefore, the metal-free CNF@NC catalyst demonstrates superior catalytic activity with an absolute four-electron transfer mechanism, strong methanol tolerance and good long-term stability towards ORR in alkaline media.

Systematic modulation and enhancement of CO{sub 2} : N{sub 2} selectivity and water stability in an isoreticular series of bio-MOF-11 analogues

Energy Technology Data Exchange (ETDEWEB)

Li, Tao; Chen, De-Li; Sullivan, Jeanne E.; Kozlowski, Mark T.; Johnson, J Karl; Rosi, Nathaniel L.

2013-02-01

An isoreticular series of cobalt-adeninate bio-MOFs (bio-MOFs 11-14) is reported. The pores of bio-MOFs 11-14 are decorated with acetate, propionate, butyrate, and valerate, respectively. The nitrogen (N{sub 2}) and carbon dioxide (CO{sub 2}) adsorption properties of these materials are studied and compared. The isosteric heats of adsorption for CO{sub 2} are calculated, and the CO{sub 2}:N{sub 2} selectivities for each material are 10 determined. As the lengths of the aliphatic chains decorating the pores in bio-MOFs 11-14 increase, the BET surface areas decrease from 1148 m{sup 2}/g to 17 m{sup 2}/g while the CO{sub 2}:N{sub 2} selectivities predicted from ideal adsorbed solution theory at 1 bar and 273 K for a 10:90 CO{sub 2}:N{sub 2} mixture range from 73:1 for bio-MOF-11 to 123:1 for bio-MOF-12 and finally to 107:1 for bio-MOF-13. At 298 K, the selectivities are 43:1 for bio-MOF-11, 52:1 for bio-MOF-12, and 40:1 for bio-MOF-13. Additionally, it is shown that 15 bio-MOF-14 exhibits a unique molecular sieving property that allows it to adsorb CO{sub 2} but not N{sub 2} at 273 and 298 K. Finally, the water stability of bio-MOFs 11-14 increases with increasing aliphatic chain length. Bio-MOF-14 exhibits no loss of crystallinity or porosity after soaking in water for one month.

Array2BIO: from microarray expression data to functional annotation of co-regulated genes

Directory of Open Access Journals (Sweden)

Rasley Amy

2006-06-01

Full Text Available Abstract Background There are several isolated tools for partial analysis of microarray expression data. To provide an integrative, easy-to-use and automated toolkit for the analysis of Affymetrix microarray expression data we have developed Array2BIO, an application that couples several analytical methods into a single web based utility. Results Array2BIO converts raw intensities into probe expression values, automatically maps those to genes, and subsequently identifies groups of co-expressed genes using two complementary approaches: (1 comparative analysis of signal versus control and (2 clustering analysis of gene expression across different conditions. The identified genes are assigned to functional categories based on Gene Ontology classification and KEGG protein interaction pathways. Array2BIO reliably handles low-expressor genes and provides a set of statistical methods for quantifying expression levels, including Benjamini-Hochberg and Bonferroni multiple testing corrections. An automated interface with the ECR Browser provides evolutionary conservation analysis for the identified gene loci while the interconnection with Crème allows prediction of gene regulatory elements that underlie observed expression patterns. Conclusion We have developed Array2BIO – a web based tool for rapid comprehensive analysis of Affymetrix microarray expression data, which also allows users to link expression data to Dcode.org comparative genomics tools and integrates a system for translating co-expression data into mechanisms of gene co-regulation. Array2BIO is publicly available at http://array2bio.dcode.org.

Hierarchical honeycomb-like Co3O4 pores coating on CoMoO4 nanosheets as bifunctional efficient electrocatalysts for overall water splitting

Science.gov (United States)

Pei, Zhihao; Xu, Li; Xu, Wei

2018-03-01

Efficient electrocatalytic water splitting is one of the most effective ways to solve the global energy crisis. In this paper, we report on a novel self-assembled hierarchical structure of Co3O4/CoMoO4 grown in situ on a bare nickel foam. The unique, three-dimensional honeycomb-like Co3O4 pores were constructed from one-dimensional nanowires and coated on two-dimensional CoMoO4 nanosheets structures grown on nickel foam. The synthesis involved a step-wise solvothermal method followed by an annealing treatment. Benefiting from the synergistic effect of the hierarchical nanostructures, the materials had more reaction active sites and a smaller electron transfer impedance, and they exhibited excellent electrocatalytic performances for the HER and OER of 143 and 244 mV, respectively, at 10 mA cm-2 in an alkaline solution. Furthermore, the materials remained stable during the long electrolysis period, over 10 h, presenting promising application prospects in the field of electrocatalytic water splitting.

BioCMOS Interfaces and Co-Design

CERN Document Server

Carrara, Sandro

2013-01-01

The application of CMOS circuits and ASIC VLSI systems to problems in medicine and system biology has led to the emergence of Bio/CMOS Interfaces and Co-Design as an exciting and rapidly growing area of research. The mutual inter-relationships between VLSI-CMOS design and the biophysics of molecules interfacing with silicon and/or onto metals has led to the emergence of the interdisciplinary engineering approach to Bio/CMOS interfaces. This new approach, facilitated by 3D circuit design and nanotechnology, has resulted in new concepts and applications for VLSI systems in the bio-world. This book offers an invaluable reference to the state-of-the-art in Bio/CMOS interfaces. It describes leading-edge research in the field of CMOS design and VLSI development for applications requiring integration of biological molecules onto the chip. It provides multidisciplinary content ranging from biochemistry to CMOS design in order to address Bio/CMOS interface co-design in bio-sensing applications.

Hierarchical porous Co3O4 films with size-adjustable pores as Li ion battery anodes with excellent rate performances

International Nuclear Information System (INIS)

Zhao, Guangyu; Xu, Zhanming; Zhang, Li; Sun, Kening

2013-01-01

Highlights: •Template-free synthesis of hierarchical porous Co 3 O 4 films on Ni foams. •Hierarchical porous Co 3 O 4 films with size-adjustable pores. •Excellent rate performances (650 mAh g −1 at 30 C) as Li ion battery anodes. -- Abstract: Constructing hierarchical porous structures on the current collectors is an attractive strategy for improving the rate performance of the Li ion battery electrodes. However, preparing hierarchical porous structures normally requires hard or soft templates to create hollows or pores in different sizes. Rigorous preparation conditions are needed to control the size (especially nanosize) and size distribution of the pores obtained by conventional methods. Herein, we describe a template-free two-step synthesis process to prepare hierarchical porous Co 3 O 4 films on Ni foam substrates. In this synthesis process, free-standing mesoporous precursor flakes are deposited on Ni foams by an electrochemical method. Subsequently, the meosporous precursor flake arrays are calcined to obtain hierarchical porous Co 3 O 4 films. More strikingly, the size of the mesopores in the flakes can be adjusted by altering the calcination temperature. The structure and morphology of the samples are characterized by scanning electron microscopy, transmission electron microscopy and Brunauer–Emmett–Teller measurements. The relationship of the in-flake-pore size and the calcinations temperature is proposed here. Electrochemical tests have revealed that the hierarchical porous Co 3 O 4 films demonstrate excellent rate performances (650 mAh g −1 at 30 C) as Li ion battery anodes due to the hierarchical porous structure, which endows fast ion transmission

Hierarchical porous microspheres of the Co3O4@graphene with enhanced electrocatalytic performance for electrochemical biosensors.

Science.gov (United States)

Yang, MinHo; Jeong, Jae-Min; Lee, Kyoung G; Kim, Do Hyun; Lee, Seok Jae; Choi, Bong Gill

2017-03-15

The integration of organic and inorganic building blocks into hierarchical porous architectures makes potentially desirable electrocatalytic materials in many electrochemical applications due to their combination of attractive qualities of dissimilar components and well-constructed charge transfer pathways. Herein, we demonstrate the preparation of the hierarchical porous Co 3 O 4 @graphene (Co 3 O 4 @G) microspheres by one-step hydrothermal method to achieve high electrocatalytic performance for enzyme-free biosensor applications. The obtained Co 3 O 4 @G microspheres are consisted of the interconnected networks of Co 3 O 4 and graphene sheets, and thus provide large accessible active sites through porous structure, while graphene sheets offer continuous electron pathways for efficient electrocatalytic reaction of Co 3 O 4 . These structural merits with synergy effect of Co 3 O 4 and graphene lead to a high performance of enzyme-free detection for glucose: high sensitivity, good selectivity, and remarkable stability. Copyright © 2016 Elsevier B.V. All rights reserved.

Charcoal injection in blast furnaces (Bio-PCI: CO2 reduction potential and economic prospects

Directory of Open Access Journals (Sweden)

Cristobal Feliciano-Bruzual

2014-07-01

Full Text Available The steel industry is under pressure to reduce its CO2 emissions, which arise from the use of coal. In the long-term, the injection of pulverized particles of charcoal from biomass through blast furnace tuyeres, in this case called Bio-PCI, is an attractive method from both an environmental and metallurgical viewpoint. The potential of Bio-PCI has been assessed in terms of its CO2 abatement potential and economic viewpoint. A cost objective function has been used to measure the impact of biochar substitution in highly fuel-efficient BF among the top nine hot metal producers; estimations are based on the relevant cost determinants of ironmaking. This contribution aims to shed light on two strategic questions: Under what conditions is the implementation of Bio-PCI economically attractive? Additionally, where is such a techno-economic innovation likely to be taken up the earliest? The results indicate the potential for an 18–40% mitigation of CO2. Findings from the economic assessment show that biochar cannot compete with fossil coal on price alone; therefore, a lower cost of biochar or the introduction of carbon taxes will be necessary to increase the competitiveness of Bio-PCI. Based on the current prices of raw materials, electricity and carbon taxes, biochar should be between 130.1 and 236.4 USD/t and carbon taxes should be between 47.1 and 198.7 USD/t CO2 to facilitate the substitution of Bio-PCI in the examined countries. In regard to implementation, Brazil, followed by India, China and the USA appeared to be in a better position to deploy Bio-PCI.

Convenient and large-scale synthesis of nitrogen-rich hierarchical porous carbon spheres for supercapacitors and CO_2 capture

International Nuclear Information System (INIS)

Chang, Binbin; Zhang, Shouren; Yin, Hang; Yang, Baocheng

2017-01-01

Highlights: • Convenient and large-scale synthesis route for N-doped hierarchical porous carbon sphere. • The resultant own spherical morphology, tunable hierarchical porosity, high surface area. • The optimal material exhibits a high CO_2 capture capacity of 4.23 mmol g"−"1. • It shows a large voltage window of 1.8 V for symmetric cell in 0.5 M Na_2SO_4. - Abstract: Herein, considering the great potential of nitrogen-doped hierarchical porous carbons in energy storage and CO_2 capture, we designed a convenient and easily large-scale production strategy for preparing nitrogen-doped hierarchical porous carbon sphere (NHPCS) materials. In this synthesis route, spherical resorcinol-formaldehyde (RF) resins were selected as carbon precursor, and then the ZnCl_2-impregnated RF resin spheres were carbonized in a NH_3 atmosphere at a temperature range of 600–800 °C. During the one-step heat-treatment process, nitrogen atom could be efficiently incorporated into the carbon skeleton, and the interconnected and hierarchical pore structure with different micro/mesopore proportion could be generated and tuned by adjusting the activating agent ZnCl_2 dosage and carbonization temperature. The resultant nitrogen-doped hierarchical porous carbon sphere materials exhibited a satisfactory charge storage capacity, and the optimal sample of NHPCS-2-8 with a high mesopore proportion obtained at 800 °C with a ZnCl_2/RF mass ratio of 2:1 presented a specific capacitance of 273.8 F g"−"1 at a current density of 0.5 A g"−"1. More importantly, the assembled NHPCS-2-8-based symmetric capacitor displayed a high energy density of 17.2 Wh kg"−"1 at a power density of 178.9 W kg"−"1 within a voltage window of 0 ∼ 1.8 V in 0.5 M Na_2SO_4 aqueous electrolyte. In addition, the CO_2 capture application of these NHPCS materials was also explored, and the optimal sample of NHPCS-0-8 with a large micropore proportion prepared at 800 °C exhibited an exceptional CO_2 uptake

Co-processing potential of HTL bio-crude at petroleum refineries

DEFF Research Database (Denmark)

Jensen, Claus Uhrenholt; Hoffmann, Jessica; Rosendahl, Lasse Aistrup

2016-01-01

An experimental study on hydrotreatment of ligno-cellulosic hydrothermal liquefaction (HTL) bio-crude to achieve a bio-feed compatible for co-processing at a refinery was made to investigate the effect of operating temperature, pressure and hydrogen to oil ratio. Using a conventional NiMo/Al2O3 h...

Hierarchically Porous Carbon Materials for CO ₂ Capture: The Role of Pore Structure

Energy Technology Data Exchange (ETDEWEB)

Estevez, Luis [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99352, United States; Barpaga, Dushyant [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99352, United States; Zheng, Jian [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99352, United States; Sabale, Sandip [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99352, United States; Patel, Rajankumar L. [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99352, United States; Zhang, Ji-Guang [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99352, United States; McGrail, B. Peter [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99352, United States; Motkuri, Radha Kishan [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99352, United States

2018-01-17

With advances in porous carbon synthesis techniques, hierarchically porous carbon (HPC) materials are being utilized as relatively new porous carbon sorbents for CO2 capture applications. These HPC materials were used as a platform to prepare samples with differing textural properties and morphologies to elucidate structure-property relationships. It was found that high microporous content, rather than overall surface area was of primary importance for predicting good CO2 capture performance. Two HPC materials were analyzed, each with near identical high surface area (~2700 m2/g) and colossally high pore volume (~10 cm3/g), but with different microporous content and pore size distributions, which led to dramatically different CO2 capture performance. Overall, large pore volumes obtained from distinct mesopores were found to significantly impact adsorption performance. From these results, an optimized HPC material was synthesized that achieved a high CO2 capacity of ~3.7 mmol/g at 25°C and 1 bar.

Hierarchical Core/Shell NiCo2O4@NiCo2O4 Nanocactus Arrays with Dual-functionalities for High Performance Supercapacitors and Li-ion Batteries

Science.gov (United States)

Cheng, Jinbing; Lu, Yang; Qiu, Kangwen; Yan, Hailong; Xu, Jinyou; Han, Lei; Liu, Xianming; Luo, Jingshan; Kim, Jang-Kyo; Luo, Yongsong

2015-07-01

We report the synthesis of three dimensional (3D) NiCo2O4@NiCo2O4 nanocactus arrays grown directly on a Ni current collector using a facile solution method followed by electrodeposition. They possess a unique 3D hierarchical core-shell structure with large surface area and dual-functionalities that can serve as electrodes for both supercapacitors (SCs) and lithium-ion batteries (LIBs). As the SC electrode, they deliver a remarkable specific capacitance of 1264 F g-1 at a current density of 2 A g-1 and ~93.4% of capacitance retention after 5000 cycles at 2 A g-1. When used as the anode for LIBs, a high reversible capacity of 925 mA h g-1 is achieved at a rate of 120 mA g-1 with excellent cyclic stability and rate capability. The ameliorating features of the NiCo2O4 core/shell structure grown directly on highly conductive Ni foam, such as hierarchical mesopores, numerous hairy needles and a large surface area, are responsible for the fast electron/ion transfer and large active sites which commonly contribute to the excellent electrochemical performance of both the SC and LIB electrodes.

Nanoparticle Decorated Ultrathin Porous Nanosheets as Hierarchical Co3O4 Nanostructures for Lithium Ion Battery Anode Materials

DEFF Research Database (Denmark)

Mujtaba, Jawayria; Sun, Hongyu; Huang, Guoyong

2016-01-01

We report a facile synthesis of a novel cobalt oxide (Co3O4) hierarchical nanostructure, in which crystalline core-amorphous shell Co3O4 nanoparticles with a bimodal size distribution are uniformly dispersed on ultrathin Co3O4 nanosheets. When tested as anode materials for lithium ion batteries...

Efficient visible light photocatalytic NO{sub x} removal with cationic Ag clusters-grafted (BiO){sub 2}CO{sub 3} hierarchical superstructures

Energy Technology Data Exchange (ETDEWEB)

Feng, Xin [Chongqing Key Laboratory of Catalysis and Functional Organic Molecules, College of Environment and Resources, Engineering Research Center for Waste Oil Recovery Technology and Equipment of Ministry of Education, College of Environment and Resources, Chongqing Technology and Business University, Chongqing 40067 (China); Zhang, Wendong [Department of Scientific Research Management, Chongqing Normal University, Chongqing 401331 (China); Deng, Hua [State Key Joint Laboratory of Environment Simulation and Pollution Control, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); Ni, Zilin [Department of Scientific Research Management, Chongqing Normal University, Chongqing 401331 (China); Dong, Fan, E-mail: dfctbu@126.com [Chongqing Key Laboratory of Catalysis and Functional Organic Molecules, College of Environment and Resources, Engineering Research Center for Waste Oil Recovery Technology and Equipment of Ministry of Education, College of Environment and Resources, Chongqing Technology and Business University, Chongqing 40067 (China); Zhang, Yuxin, E-mail: zhangyuxin@cqu.edu.cn [College of Materials Science and Engineering, National Key Laboratory of Fundamental Science of Micro/Nano-Devices and System Technology, Chongqing University, Chongqing 400044 (China)

2017-01-15

Graphical abstract: The cationic Ag clusters-grafted (BiO){sub 2}CO{sub 3} hierarchical superstructures exhibits highly enhanced visible light photocatalytic air purification through an interfacial charge transfer process induced by Ag clusters. - Highlights: • Microstructural optimization and surface cluster-grafting were firstly combined. • Cationic Ag clusters were grafted on the surface of (BiO){sub 2}CO{sub 3} superstructures. • The Ag clusters-grafted BHS displayed enhanced visible light photocatalysis. • Direct interfacial charge transfer (IFCT) from BHS to Ag clusters was proposed. • The charge transfer process and the dominant reactive species were revealed. - Abstract: A facile method was developed to graft cationic Ag clusters on (BiO){sub 2}CO{sub 3} hierarchical superstructures (BHS) surface to improve their visible light activity. Significantly, the resultant Ag clusters-grafted BHS displayed a highly enhanced visible light photocatalytic performance for NOx removal due to the direct interfacial charge transfer (IFCT) from BHS to Ag clusters. The chemical and coordination state of the cationic Ag clusters was determined with the extended X-ray absorption fine structure (EXAFS) and a theoretical structure model was proposed for this unique Ag clusters. The charge transfer process and the dominant reactive species (·OH) were revealed on the basis of electron spin resonance (ESR) trapping. A new photocatalysis mechanism of Ag clusters-grafted BHS under visible light involving IFCT process was uncovered. In addition, the cationic Ag clusters-grafted BHS also demonstrated high photochemical and structural stability under repeated photocatalysis runs. The perspective of enhancing photocatalysis through combination of microstructural optimization and IFCT could provide a new avenue for the developing efficient visible light photocatalysts.

Effect of hierarchical meso–macroporous alumina-supported copper catalyst for methanol synthesis from CO2 hydrogenation

International Nuclear Information System (INIS)

Witoon, Thongthai; Bumrungsalee, Sittisut; Chareonpanich, Metta; Limtrakul, Jumras

2015-01-01

Highlights: • CO 2 hydrogenation over Cu-loaded unimodal and hierarchical alumina catalysts. • Cu-loaded hierarchical catalyst exhibited higher methanol selectivity and stability. • The presence of macropores reduced the probability of side reaction. - Abstract: Effects of pore structures of alumina on the catalytic performance of copper catalysts for CO 2 hydrogenation were investigated. Copper-loaded hierarchical meso–macroporous alumina (Cu/HAl) catalyst exhibited no significant difference in terms of CO 2 conversion with copper-loaded unimodal mesoporous alumina (Cu/UAl) catalyst. However, the selectivity to methanol and dimethyl ether of the Cu/HAl catalyst was much higher than that of the Cu/UAl catalyst. This was attributed to the presence of macropores which diminished the occurrence of side reaction by the shortening the mesopores diffusion path length. The Cu/HAl catalyst also exhibited much higher stability than the Cu/UAl catalyst due to the fast diffusion of water out from the catalyst pellets, alleviating the oxidation of metallic copper to CuO

Hierarchical Co3O4/PANI hollow nanocages: Synthesis and application for electrode materials of supercapacitors

Science.gov (United States)

Ren, Xiaohu; Fan, Huiqing; Ma, Jiangwei; Wang, Chao; Zhang, Mingchang; Zhao, Nan

2018-05-01

Hierarchically hollow Co3O4/polyaniline nanocages (Co3O4/PANI NCs) with enhanced specific capacitance and cycle performance for electrode material of supercapacitors are fabricated by combining self-sacrificing template and in situ polymerization route. Benefiting from the good conductivity of PANI improving an electron transport rate as well as high specific surface area from such a hollow structure, the electrode made of Co3O4/PANI NCs exhibits a large specific capacitance of 1301 F/g at the current density of 1 A/g, a much enhancement is obtained as compared with the pristine Co3O4 NCs electrode. The contact resistance (Re), charge-transfer (Rct) and Warburg resistance of Co3O4/PANI NCs electrode is significantly lower than that of the pristine Co3O4 NCs electrode, indicating the enhanced electrical conductivity. In addition, the Co3O4/PANI NCs electrode also displays superior cycling stability with 90 % capacitance retention after 2000 cycles. Moreover, an aqueous asymmetric supercapacitor was successfully assembled using Co3O4/PANI NCs as the positive electrode and activated carbon (AC) as the negative electrode, the assembled device exhibits a superior energy density of 41.5 Wh/kg at 0.8 kW/kg, outstanding power density of 15.9 kW/kg at 18.4 Wh/kg, which significantly transcending those of most previously reported. These results demonstrate that the hierarchically hollow Co3O4/PANI NCs composites have a potential for fabricating electrode of supercapacitors.

3D Printing of Bio-inspired surfaces

DEFF Research Database (Denmark)

Méndez Ribó, Macarena; Islam, Aminul

The ability of the gecko to scurry across smooth or rough surfaces, regardless of inclination (vertical or even upside down), has been traced to the multiscale hierarchical structures of the gecko toe [1 - 3]. Considering all the strategies to manufacture bio-inspired surfaces, the most common is...

Construction of Hierarchical CuO/Cu2O@NiCo2S4 Nanowire Arrays on Copper Foam for High Performance Supercapacitor Electrodes

Science.gov (United States)

Zhou, Luoxiao; He, Ying; Jia, Congpu; Pavlinek, Vladimir; Saha, Petr; Cheng, Qilin

2017-01-01

Hierarchical copper oxide @ ternary nickel cobalt sulfide (CuO/Cu2O@NiCo2S4) core-shell nanowire arrays on Cu foam have been successfully constructed by a facile two-step strategy. Vertically aligned CuO/Cu2O nanowire arrays are firstly grown on Cu foam by one-step thermal oxidation of Cu foam, followed by electrodeposition of NiCo2S4 nanosheets on the surface of CuO/Cu2O nanowires to form the CuO/Cu2O@NiCo2S4 core-shell nanostructures. Structural and morphological characterizations indicate that the average thickness of the NiCo2S4 nanosheets is ~20 nm and the diameter of CuO/Cu2O core is ~50 nm. Electrochemical properties of the hierarchical composites as integrated binder-free electrodes for supercapacitor were evaluated by various electrochemical methods. The hierarchical composite electrodes could achieve ultrahigh specific capacitance of 3.186 F cm−2 at 10 mA cm−2, good rate capability (82.06% capacitance retention at the current density from 2 to 50 mA cm−2) and excellent cycling stability, with capacitance retention of 96.73% after 2000 cycles at 10 mA cm−2. These results demonstrate the significance of optimized design and fabrication of electrode materials with more sufficient electrolyte-electrode interface, robust structural integrity and fast ion/electron transfer. PMID:28914819

Construction of Hierarchical CuO/Cu2O@NiCo2S4 Nanowire Arrays on Copper Foam for High Performance Supercapacitor Electrodes

Directory of Open Access Journals (Sweden)

Luoxiao Zhou

2017-09-01

Full Text Available Hierarchical copper oxide @ ternary nickel cobalt sulfide (CuO/Cu2O@NiCo2S4 core-shell nanowire arrays on Cu foam have been successfully constructed by a facile two-step strategy. Vertically aligned CuO/Cu2O nanowire arrays are firstly grown on Cu foam by one-step thermal oxidation of Cu foam, followed by electrodeposition of NiCo2S4 nanosheets on the surface of CuO/Cu2O nanowires to form the CuO/Cu2O@NiCo2S4 core-shell nanostructures. Structural and morphological characterizations indicate that the average thickness of the NiCo2S4 nanosheets is ~20 nm and the diameter of CuO/Cu2O core is ~50 nm. Electrochemical properties of the hierarchical composites as integrated binder-free electrodes for supercapacitor were evaluated by various electrochemical methods. The hierarchical composite electrodes could achieve ultrahigh specific capacitance of 3.186 F cm−2 at 10 mA cm−2, good rate capability (82.06% capacitance retention at the current density from 2 to 50 mA cm−2 and excellent cycling stability, with capacitance retention of 96.73% after 2000 cycles at 10 mA cm−2. These results demonstrate the significance of optimized design and fabrication of electrode materials with more sufficient electrolyte-electrode interface, robust structural integrity and fast ion/electron transfer.

Fabrication of a 3D Hierarchical Sandwich Co9 S8 /α-MnS@N-C@MoS2 Nanowire Architectures as Advanced Electrode Material for High Performance Hybrid Supercapacitors.

Science.gov (United States)

Kandula, Syam; Shrestha, Khem Raj; Kim, Nam Hoon; Lee, Joong Hee

2018-05-10

Supercapacitors suffer from lack of energy density and impulse the energy density limit, so a new class of hybrid electrode materials with promising architectures is strongly desirable. Here, the rational design of a 3D hierarchical sandwich Co 9 S 8 /α-MnS@N-C@MoS 2 nanowire architecture is achieved during the hydrothermal sulphurization reaction by the conversion of binary mesoporous metal oxide core to corresponding individual metal sulphides core along with the formation of outer metal sulphide shell at the same time. Benefiting from the 3D hierarchical sandwich architecture, Co 9 S 8 /α-MnS@N-C@MoS 2 electrode exhibits enhanced electrochemical performance with high specific capacity/capacitance of 306 mA h g -1 /1938 F g -1 at 1 A g -1 , and excellent cycling stability with a specific capacity retention of 86.9% after 10 000 cycles at 10 A g -1 . Moreover, the fabricated asymmetric supercapacitor device using Co 9 S 8 /α-MnS@N-C@MoS 2 as the positive electrode and nitrogen doped graphene as the negative electrode demonstrates high energy density of 64.2 Wh kg -1 at 729.2 W kg -1 , and a promising energy density of 23.5 Wh kg -1 is still attained at a high power density of 11 300 W kg -1 . The hybrid electrode with 3D hierarchical sandwich architecture promotes enhanced energy density with excellent cyclic stability for energy storage. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Convenient and large-scale synthesis of nitrogen-rich hierarchical porous carbon spheres for supercapacitors and CO2 capture

Science.gov (United States)

Chang, Binbin; Zhang, Shouren; Yin, Hang; Yang, Baocheng

2017-08-01

Herein, considering the great potential of nitrogen-doped hierarchical porous carbons in energy storage and CO2 capture, we designed a convenient and easily large-scale production strategy for preparing nitrogen-doped hierarchical porous carbon sphere (NHPCS) materials. In this synthesis route, spherical resorcinol-formaldehyde (RF) resins were selected as carbon precursor, and then the ZnCl2-impregnated RF resin spheres were carbonized in a NH3 atmosphere at a temperature range of 600-800 °C. During the one-step heat-treatment process, nitrogen atom could be efficiently incorporated into the carbon skeleton, and the interconnected and hierarchical pore structure with different micro/mesopore proportion could be generated and tuned by adjusting the activating agent ZnCl2 dosage and carbonization temperature. The resultant nitrogen-doped hierarchical porous carbon sphere materials exhibited a satisfactory charge storage capacity, and the optimal sample of NHPCS-2-8 with a high mesopore proportion obtained at 800 °C with a ZnCl2/RF mass ratio of 2:1 presented a specific capacitance of 273.8 F g-1 at a current density of 0.5 A g-1. More importantly, the assembled NHPCS-2-8-based symmetric capacitor displayed a high energy density of 17.2 Wh kg-1 at a power density of 178.9 W kg-1 within a voltage window of 0 ∼ 1.8 V in 0.5 M Na2SO4 aqueous electrolyte. In addition, the CO2 capture application of these NHPCS materials was also explored, and the optimal sample of NHPCS-0-8 with a large micropore proportion prepared at 800 °C exhibited an exceptional CO2 uptake capacity at ambient pressures of up to 4.23 mmol g-1 at 0 °C.

Monodisperse Magneto-Fluorescent Bifunctional Nanoprobes for Bioapplications

Science.gov (United States)

Zhang, Hongwang; Huang, Heng; Pralle, Arnd; Zeng, Hao

2013-03-01

We present the work on the synthesis of dye-doped monodisperse Fe/SiO2 core/shell nanoparticles as bifunctional probes for bioapplications. Magnetic nanoparticles (NP) have been widely studied as nano-probes for bio-imaging, sensing as well as for cancer therapy. Among all the NPs, Fe NPs have been the focus because they have very high magnetization. However, Fe NPs are usually not stable in ambient due to the fast surface oxidation of the NPs. On the other hand, dye molecules have long been used as probes for bio-imaging. But they are sensitive to environmental conditions. It requires passivation for both so that they can be stable for applications. In this work, monodisperse Fe NPs with sizes ranging from 13-20 nm have been synthesized through the chemical thermal-decomposition in a solution. Silica shells were then coated on the Fe NPs by a two-phase oil-in-water method. Dye molecules were first bonded to a silica precursor and then encapsulated into the silica shell during the coating process. The silica shells protect both the Fe NPs and dye molecules, which makes them as robust probes. The dye doped Fe/SiO2 core/shell NPs remain both highly magnetic and highly fluorescent. The stable dye doped Fe/SiO2NPs have been used as a dual functional probe for both magnetic heating and local nanoscale temperature sending, and their performance will be reported. Research supported by NSF DMR 0547036, DMR1104994.

Construct hierarchical electrode with NixCo3-xS4 nanosheet coated on NiCo2O4 nanowire arrays grown on carbon fiber paper for high-performance asymmetric supercapacitors

Science.gov (United States)

Cao, Liujun; Tang, Gang; Mei, Jun; Liu, Hao

2017-08-01

In order to boost the energy density of supercapacitors, the strategy of using advanced pseudo-capacitive electrode and asymmetric device architecture is feasible and effective. Herein, we report a significant advance in the design and synthesis of a new hierarchically nanostructures with a series of controllable Ni/Co molar ratios of NixCo3-xS4 (i.e., NiCo2S4 and Ni2CoS4) nanosheets coatings have in situ grown on NiCo2O4 nanowires arrays on a flexible carbon fiber paper (CFP). Remarkably, the hybrid Ni2CoS4@NiCo2O4 composite electrode delivers the highest discharge gravimetric capacitance of 1501 F g-1, and areal capacitance of 1.86 F cm-2 at 1 mA cm-2. Furthermore, coupled with nitrogen-doped carbon xerogels anode, we have fabricated a 1.6 V asymmetric supercapacitor (Ni2CoS4@NiCo2O4//nitrogen-doped carbon xerogels), such device delivers a maximum energy and power densities of 32.2 Wh kg-1 and 2.5 kW kg-1 in 1.0 M KOH electrolyte, respectively, and an excellent cycling stability (∼87.6% retention after 10,000 cycles).

Convenient and large-scale synthesis of nitrogen-rich hierarchical porous carbon spheres for supercapacitors and CO{sub 2} capture

Energy Technology Data Exchange (ETDEWEB)

Chang, Binbin, E-mail: binbinchang@infm.hhstu.edu.cn [Institute of Nanostructured Functional Materials, Huanghe Science and Technology College, Zhengzhou, Henan 450006 (China); Henan Provincial Key Laboratory of Nano-composite and Application, Zhengzhou, Henan 450006 (China); Zhang, Shouren; Yin, Hang [Institute of Nanostructured Functional Materials, Huanghe Science and Technology College, Zhengzhou, Henan 450006 (China); Henan Provincial Key Laboratory of Nano-composite and Application, Zhengzhou, Henan 450006 (China); Yang, Baocheng, E-mail: baochengyang@yahoo.com [Institute of Nanostructured Functional Materials, Huanghe Science and Technology College, Zhengzhou, Henan 450006 (China); Henan Provincial Key Laboratory of Nano-composite and Application, Zhengzhou, Henan 450006 (China)

2017-08-01

Highlights: • Convenient and large-scale synthesis route for N-doped hierarchical porous carbon sphere. • The resultant own spherical morphology, tunable hierarchical porosity, high surface area. • The optimal material exhibits a high CO{sub 2} capture capacity of 4.23 mmol g{sup −1}. • It shows a large voltage window of 1.8 V for symmetric cell in 0.5 M Na{sub 2}SO{sub 4}. - Abstract: Herein, considering the great potential of nitrogen-doped hierarchical porous carbons in energy storage and CO{sub 2} capture, we designed a convenient and easily large-scale production strategy for preparing nitrogen-doped hierarchical porous carbon sphere (NHPCS) materials. In this synthesis route, spherical resorcinol-formaldehyde (RF) resins were selected as carbon precursor, and then the ZnCl{sub 2}-impregnated RF resin spheres were carbonized in a NH{sub 3} atmosphere at a temperature range of 600–800 °C. During the one-step heat-treatment process, nitrogen atom could be efficiently incorporated into the carbon skeleton, and the interconnected and hierarchical pore structure with different micro/mesopore proportion could be generated and tuned by adjusting the activating agent ZnCl{sub 2} dosage and carbonization temperature. The resultant nitrogen-doped hierarchical porous carbon sphere materials exhibited a satisfactory charge storage capacity, and the optimal sample of NHPCS-2-8 with a high mesopore proportion obtained at 800 °C with a ZnCl{sub 2}/RF mass ratio of 2:1 presented a specific capacitance of 273.8 F g{sup −1} at a current density of 0.5 A g{sup −1}. More importantly, the assembled NHPCS-2-8-based symmetric capacitor displayed a high energy density of 17.2 Wh kg{sup −1} at a power density of 178.9 W kg{sup −1} within a voltage window of 0 ∼ 1.8 V in 0.5 M Na{sub 2}SO{sub 4} aqueous electrolyte. In addition, the CO{sub 2} capture application of these NHPCS materials was also explored, and the optimal sample of NHPCS-0-8 with a large

Hierarchical porous NiCo2O4 nanowires for high-rate supercapacitors.

Science.gov (United States)

Jiang, Hao; Ma, Jan; Li, Chunzhong

2012-05-11

We demonstrate a simple and scalable strategy for synthesizing hierarchical porous NiCo(2)O(4) nanowires which exhibit a high specific capacitance of 743 F g(-1) at 1 A g(-1) with excellent rate performance (78.6% capacity retention at 40 A g(-1)) and cycling stability (only 6.2% loss after 3000 cycles). This journal is © The Royal Society of Chemistry 2012

Homogeneous catalytic hydrogenation of bio-oil and related model aldehydes with RuCl{sub 2}(PPh{sub 3}){sub 3}

Energy Technology Data Exchange (ETDEWEB)

Huang, F.; Li, W.; Lu, Q.; Zhu, X. [Anhui Province Key Laboratory of Biomass Clean Energy, University of Science and Technology of China, Hefei (China)

2010-12-15

A homogeneous RuCl{sub 2}(PPh{sub 3}){sub 3} catalyst was prepared for the hydrogenation of bio-oil to improve its stability and fuel quality. Experiments were first performed on three model aldehydes of acetaldehyde, furfural and vanillin selected to represent the linear aldehydes, oxygen heterocyclic aldehydes and aromatic aldehydes in bio-oil. The results demonstrated the high hydrogenation capability of this homogeneous catalyst under mild conditions (55-90 C, 1.3-3.3 MPa). The highest conversion of the three model aldehydes was over 90 %. Furfural and acetaldehyde were singly converted to furfuryl alcohol and ethanol after hydrogenation, while vanillin was mainly converted to vanillin alcohol, together with a small amount of 2-methoxy-4-methylphenol and 2-methoxyphenol. Further experiments were conducted on a bio-oil fraction extracted by ethyl acetate and on the whole bio-oil at 70 C and 3.3 MPa. Most of the aldehydes were transformed to the corresponding alcohols, and some ketones and compounds with C-C double bond were converted to more stable compounds. (Copyright copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

A top-down approach for fabricating free-standing bio-carbon supercapacitor electrodes with a hierarchical structure.

Science.gov (United States)

Li, Yingzhi; Zhang, Qinghua; Zhang, Junxian; Jin, Lei; Zhao, Xin; Xu, Ting

2015-09-23

Biomass has delicate hierarchical structures, which inspired us to develop a cost-effective route to prepare electrode materials with rational nanostructures for use in high-performance storage devices. Here, we demonstrate a novel top-down approach for fabricating bio-carbon materials with stable structures and excellent diffusion pathways; this approach is based on carbonization with controlled chemical activation. The developed free-standing bio-carbon electrode exhibits a high specific capacitance of 204 F g(-1) at 1 A g(-1); good rate capability, as indicated by the residual initial capacitance of 85.5% at 10 A g(-1); and a long cycle life. These performance characteristics are attributed to the outstanding hierarchical structures of the electrode material. Appropriate carbonization conditions enable the bio-carbon materials to inherit the inherent hierarchical texture of the original biomass, thereby facilitating effective channels for fast ion transfer. The macropores and mesopores that result from chemical activation significantly increase the specific surface area and also play the role of temporary ion-buffering reservoirs, further shortening the ionic diffusion distance.

Visible-light-driven N-(BiO)2CO3/Graphene oxide composites with improved photocatalytic activity and selectivity for NOx removal

Science.gov (United States)

Chen, Meijuan; Huang, Yu; Yao, Jie; Cao, Jun-ji; Liu, Yuan

2018-02-01

N-doped (BiO)2CO3 (NBOC)/graphene oxide (GO) composite obtained from three-dimensional hierarchical microspheres is successfully synthesized by one-pot hydrothermal method for the first time. In this synthesis, citrate ion plays a critical role in N doping. The obtained samples are used to degrade gaseous nitrogen oxides (NOx) at parts-per-billion (ppb) level under visible-light irradiation. NBOC-GO composite with 1.0 wt% graphene oxide (GO) displays the highest photocatalytic NO removal efficiency, which is 4.3 times higher than that of pristine (BiO)2CO3. Moreover, NBOC-GO composite significantly inhibits toxic NO2 intermediate production, indicating its high selectivity for NO conversion. Compared with regular GO, N doping considerably improves the catalytic performance of NBOC-GO composite, which increases NO removal by 74.6% and fully inhibits NO2 generation. The improved photocatalytic activity is mainly ascribed to extended optical absorption ability and enhanced separation efficiency of photogenerated charge carriers over NBOC-GO composite. Both results of electron spin resonance and theoretical analysis of band structure indicate that NO removal is dominated by oxidation with rad OH and rad O2- radicals. The photocatalytic activity improvement mechanism over the NBOC-GO composite is proposed accordingly based on systematic characterizations. This study demonstrates a feasible route to fabricating Bi-containing composites with high selectivity and stability for air pollution control and provides a new insight into the associated photocatalytic mechanisms.

Bio-electrochemical synthesis of commodity chemicals by autotrophic acetogens utilizing CO2 for environmental remediation.

Science.gov (United States)

Jabeen, Gugan; Farooq, Robina

2016-09-01

Bio-electrochemical synthesis (BES) is a technique in which electro-autotrophic bacteria such as Clostridium ljungdahlii utilize electric currents as an electron source from the cathode to reduce CO2 to extracellular, multicarbon, exquisite products through autotrophic conversion. The BES of volatile fatty acids and alcohols directly from CO2 is a sustainable alternative for non-renewable, petroleum-based polymer production. This conversion of CO2 implies reduction of greenhouse gas emissions. The synthesis of heptanoic acid, heptanol, hexanoic acid and hexanol, for the first time, by Clostridium ljungdahlii was a remarkable achievement of BES. In our study, these microorganisms were cultivated on the cathode of a bio-electrochemical cell at -400 mV by a DC power supply at 37 degree Centrigrade, pH 6.8, and was studied for both batch and continuous systems. Pre-enrichment of bio-cathode enhanced the electroactivity of cells and resulted in maximizing extracellular products in less time. The main aim of the research was to investigate the impact of low-cost substrate CO2, and the longer cathode recovery range was due to bacterial reduction of CO2 to multicarbon chemical commodities with electrons driven from the cathode. Reactor design was simplified for cost-effectiveness and to enhance energy efficiencies. The Columbic recovery of ethanoic acid, ethanol, ethyl butyrate, hexanoic acid, heptanoic acid and hexanol being in excess of 80 percent proved that BES was a remarkable technology.

Optical properties of monodispersive FePt nanoparticle films

Energy Technology Data Exchange (ETDEWEB)

Lee, S.J.; Lo, C.C.H. [Ames Laboratory, Iowa State University, Ames, IA 50011 (United States); Yu, A.C.C. [Sony Corporation, Sendai Technology Center, 3-4-1 Sakuragi, Miyagi 985-0842 (Japan); Fan, M. [Center for Sustainable Environmental Technologies, Iowa State University, Ames, IA 50011 (United States)

2004-10-01

The optical properties of monodispersive FePt nanoparticle films were investigated using spectroscopic ellipsometry in the energy range of 1.5 to 5.5 eV. The monodispersive FePt nanoparticle film was stabilized on a Si substrate by means of an organosilane coupling film, resulting in the formation of a (Si/SiO{sub 2}/APTS/FePt nanoparticles monolayer) structure. Multilayer optical models were employed to study the contribution of the FePt nanoparticles to the measured optical properties of the monodispersive FePt nanoparticle film, and to estimate the optical properties of the FePt nanoparticle layer. (copyright 2004 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Seaurchin-like hierarchical NiCo2O4@NiMoO4 core-shell nanomaterials for high performance supercapacitors.

Science.gov (United States)

Zhang, Qiang; Deng, Yanghua; Hu, Zhonghua; Liu, Yafei; Yao, Mingming; Liu, Peipei

2014-11-14

A novel electrode material of the three-dimensional (3D) multicomponent oxide NiCo2O4@NiMoO4 core-shell was synthesized via a facile two-step hydrothermal method using a post-annealing procedure. The uniform NiMoO4 nanosheets were grown on the seaurchin-like NiCo2O4 backbone to form a NiCo2O4@NiMoO4 core-shell material constructed by interconnected ultrathin nanosheets, so as to produce hierarchical mesopores with a large specific surface area of 100.3 m(2) g(-1). The porous feature and core-shell structure can facilitate the penetration of electrolytic ions and increases the number of electroactive sites. Hence, the NiCo2O4@NiMoO4 material exhibited a high specific capacitance of 2474 F g(-1) and 2080 F g(-1) at current densities of 1 A g(-1) and 20 A g(-1) respectively, suggesting that it has not only a very large specific capacitance, but also a good rate performance. In addition, the capacitance loss was only 5.0% after 1000 cycles of charge and discharge tests at the current density of 10 A g(-1), indicating high stability. The excellent electrochemical performance is mainly attributed to its 3D core-shell and hierarchical mesoporous structures which can provide unobstructed pathways for the fast diffusion and transportation of ions and electrons, a large number of active sites and good strain accommodation.

High-performance non-enzymatic catalysts based on 3D hierarchical hollow porous Co3O4 nanododecahedras in situ decorated on carbon nanotubes for glucose detection and biofuel cell application.

Science.gov (United States)

Wang, Shiyue; Zhang, Xiaohua; Huang, Junlin; Chen, Jinhua

2018-03-01

In this work, high-performance non-enzymatic catalysts based on 3D hierarchical hollow porous Co 3 O 4 nanododecahedras in situ decorated on carbon nanotubes (3D Co 3 O 4 -HPND/CNTs) were successfully prepared via direct carbonizing metal-organic framework-67 in situ grown on carbon nanotubes. The morphology, microstructure, and composite of 3D Co 3 O 4 -HPND/CNTs were characterized by scanning electron microscopy, transmission electron microscopy, micropore and chemisorption analyzer, and X-ray diffraction. The electrochemical characterizations indicated that 3D Co 3 O 4 -HPND/CNTs present considerably catalytic activity toward glucose oxidation and could be promising for constructing high-performance electrochemical non-enzymatic glucose sensors and glucose/O 2 biofuel cell. When used for non-enzymatic glucose detection, the 3D Co 3 O 4 -HPND/CNTs modified glassy carbon electrode (3D Co 3 O 4 -HPND/CNTs/GCE) exhibited excellent analytical performance with high sensitivity (22.21 mA mM -1  cm -2 ), low detection limit of 0.35 μM (S/N = 3), fast response (less than 5 s) and good stability. On the other hand, when the 3D Co 3 O 4 -HPND/CNTs/GCE worked as an anode of a biofuel cell, a maximum power density of 210 μW cm -2 at 0.15 V could be obtained, and the open circuit potential was 0.68 V. The attractive 3D hierarchical porous structural features, the large surface area, and the excellent conductivity based on the continuous and effective electron transport network in 3D Co 3 O 4 -HPND/CNTs endow 3D Co 3 O 4 -HPND/CNTs with the enhanced electrochemical performance and promising applications in electrochemical sensing, biofuel cell, and other energy storage and conversion devices such as supercapacitor. Graphical abstract High-performance non-enzymatic catalysts for enzymeless glucose sensing and biofuel cell based on 3D hierarchical hollow porous Co 3 O 4 nanododecahedras anchored on carbon nanotubes were successfully prepared via direct carbonizing

Hierarchically porous LaFeO3 perovskite prepared from the pomelo peel bio-template for catalytic oxidation of NO

Science.gov (United States)

Zhao, Shaojun; Wang, Li; Wang, Ying; Li, Xing

2018-05-01

In this paper, pomelo peel was used as biological template to obtain hierarchically porous LaFeO3 perovskite for the catalytic oxidation of NO to NO2. In addition, X-ray diffraction (XRD), scanning electron microscopy (SEM), N2 adsorption-desorption analyses, X-ray photoelectron spectra (XPS), NO temperature-programmed desorption (NO-TPD), oxygen temperature-programmed desorption (O2-TPD) and hydrogen temperature-programmed reduction (H2-TPR) were used to investigate the micro-structure and the redox properties of the hierarchically porous LaFeO3 perovskite prepared from pomelo peel biological template and the LaFeO3 perovskite without the biological template. The results indicated that the hierarchically porous LaFeO3 perovskite successfully replicated the porous structure of pomelo peel with high specific surface area. Compared to the LaFeO3 perovskite prepared without the pomelo peel template, the hierarchically porous LaFeO3 perovskite showed better catalytic oxidization of NO to NO2 under the same conditions. The maximum NO conversions for LaFeO3 prepared with and without template were 90% at 305 °C and 76% at 313 °C, respectively. This is mainly attributed to the higher ratio of Fe4+/Fe3+, the hierarchically porous structure with more adsorbed oxygen species and higher surface area for the hierarchically porous LaFeO3 perovskite compared with the sample prepared without the pomelo peel template.

Synthesis of Co3O4 nanocubes by hydrothermal route and their ...

Indian Academy of Sciences (India)

2018-02-02

Feb 2, 2018 ... Monodispersed Co3O4 nanocubes were prepared by a simple hydrothermal route with ... X-ray spectrometry, scanning electron microscopy and transmission electron ... spectrometry (EDS) of the product were obtained using.

Multi-layer hierarchical array fabricated with diatom frustules for highly sensitive bio-detection applications

International Nuclear Information System (INIS)

Li, Aobo; Cai, Jun; Pan, Junfeng; Wang, Yu; Yue, Yue; Zhang, Deyuan

2014-01-01

Diatoms have delicate porous structures which are very beneficial in improving the absorbing ability in the bio-detection field. In this study, multi-layered hierarchical arrays were fabricated by packing Nitzschia soratensis (N. soratensis) frustules into Cosinodiscus argus (C. argus) frustules to achieve advanced sensitivity in bio-detection chips. Photolithographic patterning was used to obtain N. soratensis frustule arrays, and the floating behavior of C. argus frustules was employed to control their postures for packing N. soratensis frustule array spots. The morphology of the multi-layer C. argus–N. soratensis package array was investigated by scanning electron microscopy, demonstrating that the overall and sub-structures of the diatom frustules were retained. The signal enhancing effect of multi-layer C. argus–N. soratensis packages was demonstrated by fluorescent antibody test results. The mechanism of the enhancement was also analyzed, indicating that both complex hierarchical frustule structures and optimized posture of C. argus frustules were important for improving bio-detection sensitivities. The technique for fabricating multi-layer diatom frustules arrays is also useful for making multi-functional biochips and controllable drug delivery systems. (paper)

Hierarchically porous micro-rod lithium-rich cathode material Li1.2Ni0.13Mn0.54Co0.13O2 for high performance lithium-ion batteries

International Nuclear Information System (INIS)

Zhang, Linjing; Borong, Wu.; Ning, Li.; Feng, Wu.

2014-01-01

Graphical abstract: - Highlights: • The hierarchically porous micro-rod Li 1.2 Ni 0.13 Mn 0.54 Co 0.13 O 2 material is prepared by a facile hydrothermal method. • This material exhibits good cycling performance. • It delivers discharge capacities of 280.7, 254.8, 232.3, 225.6, 201.7 and 172.7 mAh g −1 at 0.1 C, 0.2 C, 0.5 C, 1 C, 2 C and 5 C rates, respectively. • Excellent rate capability and cycleability are obtained attributed to the hierarchically porous micro-rod structure. - Abstract: Lithium-rich cathode material Li 1.2 Ni 0.13 Mn 0.54 Co 0.13 O 2 with hierarchically porous micro-rod structures has been synthesized using a facile hydrothermal method. The morphology and XRD patterns explain the formation mechanism of the sample. Micro-rod oxalates precursor with rough surface is formed during the hydrothermal reaction, and then the product with hierarchically porous structures constructed of nanoparticles is synthesized during the sintering process at high temperatures. The electrochemical performance results show that the as-prepared sample exhibits high capacities, good cycleability and outstanding rate capability. It delivers discharge capacities of 280.7, 254.8, 232.3, 225.6, 201.7 and 172.7 mAh g −1 at 0.1 C, 0.2 C, 0.5 C, 1 C, 2 C and 5 C rates, respectively. The cycle voltammograms indicate the good reversibility of the as-prepared Li 1.2 Ni 0.13 Mn 0.54 Co 0.13 O 2 material. The high onset temperature of the exothermal peak in the differential scanning calorimetry curve implies its good thermal stability. The good performance of the as-prepared material is endowed by its hierarchically porous structures

Synthesis and Magnetic Properties of Nearly Monodisperse CoFe2O4Nanoparticles Through a Simple Hydrothermal Condition

Directory of Open Access Journals (Sweden)

Li Xing-Hua

2010-01-01

Full Text Available Abstract Nearly monodisperse cobalt ferrite (CoFe2O4 nanoparticles without any size-selection process have been prepared through an alluring method in an oleylamine/ethanol/water system. Well-defined nanospheres with an average size of 5.5 nm have been synthesized using metal chloride as the law materials and oleic amine as the capping agent, through a general liquid–solid-solution (LSS process. Magnetic measurement indicates that the particles exhibit a very high coercivity at 10 K and perform superparamagnetism at room temperature which is further illuminated by ZFC/FC curves. These superparamagnetic cobalt ferrite nanomaterials are considered to have potential application in the fields of biomedicine. The synthesis method is possible to be a general approach for the preparation of other pure binary and ternary compounds.

Co-Processing of Jatropha-Derived Bio-Oil with Petroleum Distillates over Mesoporous CoMo and NiMo Sulfide Catalysts

Directory of Open Access Journals (Sweden)

Shih-Yuan Chen

2018-02-01

Full Text Available The co-processing of an unconventional type of Jatropha bio-oil with petroleum distillates over mesoporous alumina-supported CoMo and NiMo sulfide catalysts (denoted CoMo/γ-Al2O3 and NiMo/γ-Al2O3 was studied. Either a stainless-steel high-pressure batch-type reactor or an up-flow fixed-bed reaction system was used under severe reaction conditions (330–350 °C and 5–7 MPa, similar to the conditions of the conventional diesel hydrodesulfurization (HDS process. To understand the catalytic performance of the mesoporous sulfide catalysts for co-processing, we prepared two series of oil feedstocks. First, model diesel oils, consisting of hydrocarbons and model molecules with various heteroatoms (sulfur, oxygen, and nitrogen were used for the study of the reaction mechanisms. Secondly, low-grade oil feedstocks, which were prepared by dissolving of an unconventional type of Jatropha bio-oil (ca. 10 wt % in the petroleum distillates, were used to study the practical application of the catalysts. Surface characterization by gas sorption, spectroscopy, and electron microscopy indicated that the CoMo/γ-Al2O3 sulfide catalyst, which has a larger number of acidic sites and coordinatively unsaturated sites (CUS on the mesoporous alumina framework, was associated with small Co-incorporated MoS2-like slabs with high stacking numbers and many active sites at the edges and corners. In contrast, the NiMo/γ-Al2O3 sulfide catalyst, which had a lower number of acidic sites and CUS on mesoporous alumina framework, was associated with large Ni-incorporated MoS2-like slabs with smaller stacking numbers, yielding more active sites at the brims and corresponding to high hydrogenation (HYD activity. Concerning the catalytic performance, the mesoporous CoMo/γ-Al2O3 sulfide catalyst with large CUS number was highly active for the conventional diesel HDS process; unfortunately, it was deactivated when oxygen- and nitrogen-containing model molecules or Jatropha bio

High lithium storage capacity achieved by regulating monodisperse C/In{sub 2}O{sub 3} nanosheet composite with double phases

Energy Technology Data Exchange (ETDEWEB)

Yue, Lu; Pan, Xueqian; Chen, Shangqian; Song, Jialing; Liu, Cheng [Key Laboratory for Advanced Technology in Environmental Protection of Jiangsu Province, Yancheng Institute of Technology, Jiangsu, 224051 (China); Luo, Gaixia [Department of Physics, Yancheng Institute of Technology, Jiangsu, 224051 (China); Guan, Rongfeng [Key Laboratory for Advanced Technology in Environmental Protection of Jiangsu Province, Yancheng Institute of Technology, Jiangsu, 224051 (China); Zhang, Wenhui, E-mail: zwhuizi000@sina.com [Key Laboratory for Advanced Technology in Environmental Protection of Jiangsu Province, Yancheng Institute of Technology, Jiangsu, 224051 (China)

2017-06-01

Monodisperse C/In{sub 2}O{sub 3} nanosheet composites are prepared by D-fructose-assisted solvothermal approach. The effects of carbon content on the morphological evolution and electrochemical performance of C/In{sub 2}O{sub 3} nanosheet composites are investigated. The SEM and TEM are used to study the morphological evolution. C/In{sub 2}O{sub 3} nanosheet composite electrode with 17.3% carbon content exhibits the highest reversible capacity of 1639 mAh g{sup -1} over 100 cycles at a current density of 100 mA g{sup -1} and maintains the best discharge capacity of 782 mAh g{sup -1} over 400 cycles at a current density of 400 mA g{sup -1} for reported In{sub 2}O{sub 3} based anode materials to date. - Highlights: • Monodisperse carbon/In{sub 2}O{sub 3} nanosheet composites have been synthesized via D-fructose-assisted solvothermal approach. • The prepared electrode exhibited high reversible discharge capacity of 1639 mAh g{sup -1} over 100 cycles. • The prepared electrode maintained the discharge capacity of 782 mAh g{sup -1} over 400 cycles at 400 mA g{sup -1}.

Hierarchically scaffolded CoP/CoP2 nanoparticles: controllable synthesis and their application as a well-matched bifunctional electrocatalyst for overall water splitting.

Science.gov (United States)

Li, Wan; Zhang, Shilin; Fan, Qining; Zhang, Fazhi; Xu, Sailong

2017-05-04

Transition metal phosphide (TMP) nanostructures have stimulated increasing interest for use in water splitting owing to their abundant natural sources and high activity for the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). Typically, the preparation of hierarchical TMPs involves the utilization of expensive or dangerous phosphorus sources, and, in particular, the understanding of topotactic transformations of the precursors to crystalline phases-which could be utilized to enhance electrocatalytic performance-remains very limited. We, herein, report a controllable preparation of CoP/CoP 2 nanoparticles well dispersed in flower-like Al 2 O 3 scaffolds (f-CoP/CoP 2 /Al 2 O 3 ) as a bifunctional electrocatalyst for the HER and OER via the phosphorization of a flower-like CoAl layered double hydroxide precursor. Characterization by in situ X-ray diffraction (XRD) monitored the topotactic transformation underlying the controllable formation of CoP/CoP 2 via tuning the phosphorization time. Electrocatalytic tests showed that an f-CoP/CoP 2 /Al 2 O 3 electrode exhibited a lower onset potential and higher electrocatalytic activity for the HER and OER in the same alkaline electrolyte than electrodes of flower-like and powdered CoP/Al 2 O 3 . The enhanced electrochemical performance was experimentally supported by measuring the electrochemically active surface area. The f-CoP/CoP 2 /Al 2 O 3 composite further generated a current density of 10 mA cm -2 at 1.65 V when used as a bifunctional catalyst for overall water splitting. Our results demonstrate that the preparation route based on the LDH precursor may provide an alternative for investigating diverse TMPs as bifunctional electrocatalysts for water splitting.

Bio diesel Production via Transesterification of Palm Oil Using NaOH/ Al2O3 Catalysts

International Nuclear Information System (INIS)

Taufiq Yap Yun Hin; Nurul Fitriyah Abdullah; Mahiran Basri; Taufiq Yap Yun Hin; Nurul Fitriyah Abdullah

2011-01-01

Due to the increase in price of petroleum and environmental concerns, the search for alternative fuels has gained importance. In this work, bio diesel production by transesterification of palm oil with methanol has been studied in a heterogeneous system using sodium hydroxide loaded on alumina (NaOH/ Al 2 O 3 ). NaOH/ Al 2 O 3 catalyst was prepared by impregnation of alumina with different amount of an aqueous solution of sodium hydroxide followed by calcination in air for 3 h. The prepared catalysts were then characterized by using x-ray diffraction (XRD), Fourier transform infrared spectrometer (FT-IR), Brunner-Emmett-Teller surface area measurement (BET), scanning electron microscopy (SEM) and temperature-programmed desorption of CO 2 (CO 2 -TPD). Moreover, the dependence of the conversion of palm oil on the reactions variables such as the molar ratio of methanol/oil, the amount of catalysts used, reaction temperatures and reaction times were performed. The conversion of 99 % was achieved under the optimum reaction conditions. The bio diesel obtained was characterized by FT-IR and the pour point was measured. (author)

Hierarchical hollow spheres of Fe2O3 @polyaniline for lithium ion battery anodes.

Science.gov (United States)

Jeong, Jae-Min; Choi, Bong Gill; Lee, Soon Chang; Lee, Kyoung G; Chang, Sung-Jin; Han, Young-Kyu; Lee, Young Boo; Lee, Hyun Uk; Kwon, Soonjo; Lee, Gaehang; Lee, Chang-Soo; Huh, Yun Suk

2013-11-20

Hierarchical hollow spheres of Fe2 O3 @polyaniline are fabricated by template-free synthesis of iron oxides followed by a post in- and exterior construction. A combination of large surface area with porous structure, fast ion/electron transport, and mechanical integrity renders this material attractive as a lithium-ion anode, showing superior rate capability and cycling performance. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Monodisperse Pt atoms anchored on N-doped graphene as efficient catalysts for CO oxidation: A first-principles investigation

KAUST Repository

Liu, Xin; Sui, Yanhui; Duan, Ting; Meng, Changgong; Han, Yu

2015-01-01

We performed first-principles based calculations to investigate the electronic structure and the potential catalytic performance of Pt atoms monodispersed on N-doped graphene in CO oxidation. We showed that N-doping can introduce localized defect states in the vicinity of the Fermi level of graphene which will effectively stabilize the deposited Pt atoms. The binding energy of a single Pt atom onto a stable cluster of 3 pyridinic N (PtN3) is up to -4.47 eV, making the diffusion and aggregation of anchored Pt atoms difficult. Both the reaction thermodynamics and kinetics suggest that CO oxidation over PtN3 would proceed through the Langmuir-Hinshelwood mechanism. The reaction barriers for the formation and dissociation of the peroxide-like intermediate are determined to be as low as 0.01 and 0.08 eV, respectively, while that for the regeneration is only 0.15 eV, proving the potential high catalytic performance of PtN3 in CO oxidation, especially at low temperatures. The Pt-d states that are up-shifted by the Pt-N interaction account for the enhanced activation of O2 and the efficient formation and dissociation of the peroxide-like intermediate.

Optimization of a simple technique for preparation of monodisperse poly(lactide-co-glycolide) nanospheres

Energy Technology Data Exchange (ETDEWEB)

Ito, Fuminori, E-mail: fuminoito@spice.ocn.ne.jp [Tokyo Metropolitan University, Department of Applied Chemistry, Graduate School of Urban Environmental Sciences (Japan)

2016-09-15

In this study, we report the optimization of a solvent evaporation technique for preparing monodisperse poly-(lactide-co-glycolide) (PLGA) nanospheres, from a mixture of solvents composed of ethanol and PVA solution. Various experimental conditions were investigated in order to control the particle size and size distribution of the nanospheres. In addition, nanospheres containing rifampicin (RFP, an antituberculosis drug), were prepared using PLGA of various molecular weights, to study the effects of RFP as a model hydrophobic drug. The results showed that a higher micro-homogenizer stirring rate facilitated the preparation of monodisperse PLGA nanospheres with a low coefficient of variation (~20 %), with sizes below 200 nm. Increasing the PLGA concentration from 0.1 to 0.5 g resulted in an increase in the size of the obtained nanospheres from 130 to 174 nm. The molecular weight of PLGA had little effect on the particle sizes and particle size distributions of the nanospheres. However, the drug loading efficiencies of the obtained RFP/PLGA nanospheres decreased when the molecular weight of PLGA was increased. Based on these experiments, an optimized technique was established for the preparation of monodisperse PLGA nanospheres, using the method developed by the authors.Graphical Abstract.

Creating bio-inspired hierarchical 3D–2D photonic stacks via planar lithography on self-assembled inverse opals

International Nuclear Information System (INIS)

Burgess, Ian B; Aizenberg, Joanna; Lončar, Marko

2013-01-01

Structural hierarchy and complex 3D architecture are characteristics of biological photonic designs that are challenging to reproduce in synthetic materials. Top–down lithography allows for designer patterning of arbitrary shapes, but is largely restricted to planar 2D structures. Self-assembly techniques facilitate easy fabrication of 3D photonic crystals, but controllable defect-integration is difficult. In this paper we combine the advantages of top–down and bottom–up fabrication, developing two techniques to deposit 2D-lithographically-patterned planar layers on top of or in between inverse-opal 3D photonic crystals and creating hierarchical structures that resemble the architecture of the bright green wing scales of the butterfly, Parides sesostris. These fabrication procedures, combining advantages of both top–down and bottom–up fabrication, may prove useful in the development of omnidirectional coloration elements and 3D–2D photonic crystal devices. (paper)

Toxicity of inhaled 238PuO2 in beagle dogs. A. Monodisperse 1.5 μm 238PuO2. B. Monodisperse 3.0 μm 238PuO2 particles. III

International Nuclear Information System (INIS)

Lustgarten, C.S.; Mewhinney, J.A.; Hobbs, C.H.; Halliwell, W.H.; Jones, R.K.; Mauderly, J.L.; McClellan, R.O.; Mo, T.; Pickrell, J.A.

1976-01-01

To obtain essential information on the importance of the homogeneity or non-homogeneity of the radiation dose to lung (the hot particle question), Beagle dogs have been exposed to monodisperse aerosols (sigma/sub g/ 238 PuO 2 of either 1.5 μm or 3.0 μm aerodynamic diameter (AD). By using monodisperse particles of these two sizes, the average dose to lung is held constant for a given initial lung burden, but the local alpha dose around the two sizes of particles varies by a factor of about ten. All exposures have been completed with 72 days exposed to each of the two particle sizes of 238 PuO 2 (total of 144 dogs) resulting in graded initial lung burdens which range from .005 to 2.2 μCi/kg of body weight. Twenty-four dogs exposed to the diluent aerosol are serving as controls. The animals will be studied over their total life span. Two exposed dogs have died from pulmonary injury: Dog 710C (with an initial lung burden of 2.0 μCi/kg) died at 631 days after inhalation of 3.0 μm AD aerosol. The cause of death was radiation pneumonitis and pulmonary fibrosis, Dog 746B (with an initial lung burden of 1.3 μCi/kg) died at 791 days after inhalation of 1.5 μm AD aerosol. Death was attributed to intrapulmonic hemorrhage resulting from a degenerative vasculitis. One control dog (721A) was euthanized at 820 days after exposure due to a meningitis and encephalomalacia that caused a severe central nervous system disorder that made the dog difficult to handle.A leukopenia in exposed dogs to date has occurred earlier and to a greater degree in dogs exposed to 3.0 μm AD particles than in dogs that recevied 1.5 μm AD particles. One hundred forty-two exposed and 23 control dogs are surviving at 175 to 1024 days after exposure

Hierarchical CuCo2O4 nanobelts as a supercapacitor electrode with high areal and specific capacitance

International Nuclear Information System (INIS)

Vijayakumar, Subbukalai; Lee, Seong-Hun; Ryu, Kwang-Sun

2015-01-01

Highlights: • First time we report the synthesis of CuCo 2 O 4 nanobelts using hydrothermal method. • The spinel CuCo 2 O 4 nanobelts exhibit maximum areal capacitance of 2.42 F cm −2 . • After 1800 cycles, 127% of the initial specific capacitance was retained. - Abstract: One dimensional hierarchical CuCo 2 O 4 nanobelt like architecture was synthesized via hydrothermal method. The synthesized nanomaterial was characterized using X-ray diffraction (XRD) analysis, field emission scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). The TEM image clearly shows the nanobelt like architecture of CuCo 2 O 4 . The supercapacitor properties of CuCo 2 O 4 nanobelts electrode were tested using cyclic voltammetry, charge-discharge and electrochemical impedance spectroscopy. The spinel CuCo 2 O 4 nanobelts exhibit maximum areal and specific capacitance of 2.42 F cm −2 (809 F g −1 ). After 1800 continuous charge-discharge cycles, 127% of the initial capacitance was retained. This superior electrochemical supercapacitor property is mainly due to increased surface area and ion transport of nanobelt like architecture. The charge transfer resistance (R ct ) value of CuCo 2 O 4 nanobelt electrode is 3.85 Ω. This high capacitance and cyclic stability demonstrate that the prepared CuCo 2 O 4 nanobelts are a promising candidate for supercapacitors.

Mace-like hierarchical MoS2/NiCo2S4 composites supported by carbon fiber paper: An efficient electrocatalyst for the hydrogen evolution reaction

Science.gov (United States)

Sun, Lan; Wang, Tao; Zhang, Long; Sun, Yunjin; Xu, Kewei; Dai, Zhengfei; Ma, Fei

2018-02-01

The rational design and preparation of earth-abundant, stable and efficient electrocatalysts for hydrogen production is currently the subject in extensive scientific and technological researches toward the future of a clean-energy society. Herein, a mace-like MoS2/NiCo2S4 hierarchical structure is designed and synthesized on carbon fiber paper via a facile hydrothermal method, and evaluated as electrocatalyst for hydrogen evolution reaction. In the MoS2/NiCo2S4/carbon fiber paper hierarchical structures, MoS2 nanosheets are dispersively distributed on the surface of NiCo2S4 nanowires, which provides an enlarged surface area, abundant interfaces and catalytic active sites. As for hydrogen evolution reaction, such MoS2/NiCo2S4/carbon fiber paper heterostructures give rise to a hydrogen evolution reaction catalytic current density of 10 mA cm-2 with a lower overpotential of 139 mV and a smaller Tafel slope of 37 mV·dec-1 than those of MoS2/carbon fiber paper and NiCo2S4/carbon fiber paper counterparts, exhibiting a prominent electrocatalytic performance. Moreover, the electrocatalytic properties change little after 5000 CV cycles and continual electrolysis for 12 h without obvious decay, respectively, demonstrating high durability and stability. The excellent hydrogen evolution reaction performances endow the hierarchical configuration MoS2/NiCo2S4/carbon fiber paper with promising alternative in HER and other related renewable energy fields.

Hierarchical chestnut-like MnCo2O4 nanoneedles grown on nickel foam as binder-free electrode for high energy density asymmetric supercapacitors

Science.gov (United States)

Hui, Kwun Nam; Hui, Kwan San; Tang, Zikang; Jadhav, V. V.; Xia, Qi Xun

2016-10-01

Hierarchical chestnut-like manganese cobalt oxide (MnCo2O4) nanoneedles (NNs) are successfully grown on nickel foam using a facile and cost-effective hydrothermal method. High resolution TEM image further verifies that the chestnut-like MnCo2O4 structure is assembled by numerous 1D MnCo2O4 nanoneedles, which are formed by numerous interconnected MnCo2O4 nanoparticles with grain diameter of ∼10 nm. The MnCo2O4 electrode exhibits high specific capacitance of 1535 F g-1 at 1 A g-1 and good rate capability (950 F g-1 at 10 A g-1) in a 6 M KOH electrolyte. An asymmetric supercapacitor is fabricated using MnCo2O4 NNs on Ni foam (MnCo2O4 NNs/NF) as the positive electrode and graphene/NF as the negative electrode. The device shows an operation voltage of 1.5 V and delivers a high energy density of ∼60.4 Wh kg-1 at a power density of ∼375 W kg-1. Moreover, the device exhibits an excellent cycling stability of 94.3% capacitance retention after 12000 cycles at 30 A g-1. This work demonstrates that hierarchical chestnut-like MnCo2O4 NNs could be a promising electrode for the high performance energy storage devices.

A top-down approach for fabricating free-standing bio-carbon supercapacitor electrodes with a hierarchical structure

OpenAIRE

Yingzhi Li; Qinghua Zhang; Junxian Zhang; Lei Jin; Xin Zhao; Ting Xu

2015-01-01

Biomass has delicate hierarchical structures, which inspired us to develop a cost-effective route to prepare electrode materials with rational nanostructures for use in high-performance storage devices. Here, we demonstrate a novel top-down approach for fabricating bio-carbon materials with stable structures and excellent diffusion pathways; this approach is based on carbonization with controlled chemical activation. The developed free-standing bio-carbon electrode exhibits a high specific ca...

The Density and Compressibility of BaCO3-SrCO3-CaCO3-K2CO3-Na2CO3-Li2CO3 Liquids: New Measurements and a Systematic Trend with Cation Field Strength

Science.gov (United States)

Hurt, S. M.; Lange, R. A.; Ai, Y.

2015-12-01

The volumetric properties of multi-component carbonate liquids are required to extend thermodynamic models that describe partial melting of the deep mantle (e.g. pMELTS; Ghiorso et al., 2003) to carbonate-bearing lithologies. Carbonate in the mantle is an important reservoir of carbon, which is released to the atmosphere as CO2 through volcanism, and thus contributes to the carbon cycle. Although MgCO3 is the most important carbonate component in the mantle, it is not possible to directly measure the 1-bar density and compressibility of MgCO3 liquid because, like other alkaline-earth carbonates, it decomposes at a temperature lower than its melting temperature. Despite this challenge, Liu and Lange (2003) and O'Leary et al. (2015) showed that the one bar molar volume, thermal expansion and compressibility of the CaCO3 liquid component could be obtained by measuring the density and sound speeds of stable liquids in the CaCO3-Li2CO3-Na2CO3-K2CO3 quaternary system at one bar. In this study, this same strategy is employed on SrCO3- and BaCO3-bearing alkali carbonate liquids. The density and sound speed of seven liquids in the SrCO3-Li2CO3-Na2CO3-K2CO3 quaternary and three liquids in the BaCO3-Li2CO3-Na2CO3-K2CO3 quaternary were measured from 739-1367K, with SrCO3 and BaCO3 concentrations ranging from 10-50 mol%. The density measurements were made using the double-bob Archimedean method and sound speeds were obtained with a frequency-sweep acoustic interferometer. The molar volume and sound speed measurements were used to calculate the isothermal compressibility of each liquid, and the results show the volumetric properties mix ideally with composition. The partial molar volume and compressibility of the SrCO3 and BaCO3 components are compared to those obtained for the CaCO3 component as a function of cation field strength. The results reveal a systematic trend that allows the partial molar volume and compressibility of the MgCO3 liquid component to be estimated.

Biotemplating of Luffa cylindrica sponges to self-supporting hierarchical zeolite macrostructures for bio-inspired structured catalytic reactors

International Nuclear Information System (INIS)

Zampieri, Alessandro; Mabande, Godwin T.P.; Selvam, Thangaraj; Schwieger, Wilhelm; Rudolph, Alexander; Hermann, Ralph; Sieber, Heino; Greil, Peter

2006-01-01

Biomorphic self-supporting MFI-type zeolite frameworks with hierarchical porosity and complex architecture were prepared using a 2-step (in-situ seeding and secondary crystal growth) hydrothermal synthesis in the presence of a biological template (Luffa sponge), employed as a macroscale sacrificial structure builder. The bio-inspired zeolitic replica inherited the complex spongy morphology and the intricate open-porous architecture of the biotemplate. Moreover, it exhibited reasonable mechanical stability in order to study the applicability of the biomorphic catalyst in a technical catalytic process. A bio-inspired catalytic reactor utilising the self-supporting ZSM-5 scaffold in monolithic configuration was developed in order to test the catalytic performance of the material

Hydrothermal fabrication of N-doped (BiO){sub 2}CO{sub 3}: Structural and morphological influence on the visible light photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Dong, Fan, E-mail: dfctbu@126.com [Chongqing Key Laboratory of Catalysis and Functional Organic Molecules, College of Environmental and Biological Engineering, Chongqing Technology and Business University, Chongqing 400067 (China); Wang, Rui; Li, Xinwei [Chongqing Key Laboratory of Catalysis and Functional Organic Molecules, College of Environmental and Biological Engineering, Chongqing Technology and Business University, Chongqing 400067 (China); Ho, Wing-Kei [Department of Science and Environmental Studies, The Centre for Education in Environmental Sustainability, The Hong Kong Institute of Education, Hong Kong (China)

2014-11-15

Graphical abstract: - Highlights: • Persimmon-like, flower-like N-doped (BiO){sub 2}CO{sub 3} superstructures were prepared. • The superstructures were fabricated by one-step hydrothermal method. • The hydrothermal temperature controlled the morphological structure. • N-doped (BiO){sub 2}CO{sub 3} superstructure showed enhanced photocatalytic activity. • The high activity can be ascribed to doped nitrogen and hierarchical structure. - Abstract: Various 3D N-doped (BiO){sub 2}CO{sub 3} (N-BOC) hierarchical superstructures self-assembled with 2D nanosheets were fabricated by one-step hydrothermal treatment of bismuth citrate and urea. The as-obtained samples were characterized by XRD, XPS, FT-IR, SEM, N{sub 2} adsorption–desorption isotherms and UV–vis DRS. The hydrothermal temperature plays a crucial role in tuning the crystal and morphological structure of the samples. Adjusting the reaction temperature to 150, 180 and 210 °C, we obtained N-doped (BiO){sub 2}CO{sub 3} samples with corresponding attractive persimmon-like, flower-like and nanoflakes nano/microstructures. The photocatalytic activities of the samples were evaluated by removal of NO under visible and solar light irradiation. The results revealed that the N-doped (BiO){sub 2}CO{sub 3} hierarchical superstructures showed enhanced visible light photocatalytic activity compared to pure (BiO){sub 2}CO{sub 3} and TiO{sub 2}-based visible light photocatalysts. The outstanding photocatalytic performance of N-BOC samples can be ascribed to the doped nitrogen and the special hierarchical structure. The present work could provide new perspectives in controlling the morphological structure and photocatalytic activity of photocatalyst for better environmental pollution control.

Hierarchical Mn2O3 Microspheres In-Situ Coated with Carbon for Supercapacitors with Highly Enhanced Performances

Science.gov (United States)

Gong, Feilong; Lu, Shuang; Peng, Lifang; Zhou, Jing; Kong, Jinming; Jia, Dianzeng; Li, Feng

2017-01-01

Porous Mn2O3 microspheres have been synthesized and in-situ coated with amorphous carbon to form hierarchical C@Mn2O3 microspheres by first producing MnCO3 microspheres in solvothermal reactions, and then annealing at 500 °C. The self-assembly growth of MnCO3 microspheres can generate hollow structures inside each of the particles, which can act as micro-reservoirs to store biomass-glycerol for generating amorphous carbon onto the surfaces of Mn2O3 nanorods consisting of microspheres. The C@Mn2O3 microspheres, prepared at 500 °C, exhibit highly enhanced pseudocapacitive performances when compared to the particles after annealed at 400 °C and 600 °C. Specifically, the C@Mn2O3 microspheres prepared at 500 °C show high specific capacitances of 383.87 F g−1 at current density of 0.5 A g−1, and excellent cycling stability of 90.47% of its initial value after cycling for 5000 times. The asymmetric supercapacitors assembled with C@Mn2O3 microspheres after annealed at 500 °C and activated carbon (AC) show an energy density of up to 77.8 Wh kg−1 at power density of 500.00 W kg−1, and a maximum power density of 20.14 kW kg−1 at energy density of 46.8 Wh kg−1. We can attribute the enhanced electrochemical performances of the materials to their three-dimensional (3D) hierarchical structure in-situ coated with carbon. PMID:29168756

Hierarchical Mn2O3 Microspheres In-Situ Coated with Carbon for Supercapacitors with Highly Enhanced Performances

Directory of Open Access Journals (Sweden)

Feilong Gong

2017-11-01

Full Text Available Porous Mn2O3 microspheres have been synthesized and in-situ coated with amorphous carbon to form hierarchical C@Mn2O3 microspheres by first producing MnCO3 microspheres in solvothermal reactions, and then annealing at 500 °C. The self-assembly growth of MnCO3 microspheres can generate hollow structures inside each of the particles, which can act as micro-reservoirs to store biomass-glycerol for generating amorphous carbon onto the surfaces of Mn2O3 nanorods consisting of microspheres. The C@Mn2O3 microspheres, prepared at 500 °C, exhibit highly enhanced pseudocapacitive performances when compared to the particles after annealed at 400 °C and 600 °C. Specifically, the C@Mn2O3 microspheres prepared at 500 °C show high specific capacitances of 383.87 F g−1 at current density of 0.5 A g−1, and excellent cycling stability of 90.47% of its initial value after cycling for 5000 times. The asymmetric supercapacitors assembled with C@Mn2O3 microspheres after annealed at 500 °C and activated carbon (AC show an energy density of up to 77.8 Wh kg−1 at power density of 500.00 W kg−1, and a maximum power density of 20.14 kW kg−1 at energy density of 46.8 Wh kg−1. We can attribute the enhanced electrochemical performances of the materials to their three-dimensional (3D hierarchical structure in-situ coated with carbon.

3D self-supported hierarchical Ni−Co architectures with integrated capacitive performance and enhanced electronic conductivity for supercapacitors

International Nuclear Information System (INIS)

Tang, YanRu; Cheng, Baohai

2016-01-01

3D self-supported hierarchical Ni and Co co-hydroxide architectures are promising electrode materials for supercapacitor application attributed to their prominent properties such as binder-free electrode fabrication process and high power density. However, the intrinsic conductivity of Ni and Co co-hydroxide is poor. How to develop a new type of supercapacitors exhibiting enhanced electronic conductivity and involving pseudocapacitive performance and electric double-layer capacitive performance is still challenging. Herein, we present a facile co-electrodeposition method to fabricate self-standing Ni_xCo_2_x(OH)_y@Ni/ITO monolithic electrode by growing a layer of Ni_xCo_2_x(OH)_y with layered structure on surface of conductive Ni nanotube, which increases specific surface area and prompts fast ion adsorption/de-adsotption (electrochemical double layer capacitance performance) and fast surface redox reactions (pseudo-capacitance performance). With the conductive Ni nanotube as current collector and electronic conductor, the binder-free Ni_xCo_2_x(OH)_y@Ni/ITO electrode exhibits high specific capacitance (92.4 mF cm"−"2 at 0.1 mA cm"−"2, the mass of active material per cm"−"2 is typically in 100 s μg). Moreover, Ni_xCo_2_x(OH)_y@Ni/ITO hybrids display excellent cycling stability with 93.3% capacitance retention after 5000 cycles. The results suggest Ni_xCo_2_x(OH)_y@Ni/ITO nanostructure constructed based on integrated features of pseudocapacitive performance and electric double-layer capacitive performance and enhanced electronic conductivity is expected to be a type of excellent electrode material for supercapacitor. - Highlights: • Ni−Co electrode is fabricated by growing layered structure on Ni nanotube surface. • The layered structure prompts fast ion adsorption/de-adsotption and redox reactions. • The Ni nanotube serves as nanostructured current collector and electronic conductor. • The Ni−Co hybrids display 93.3% capacitance retention

Rational Design of a Hierarchical Tin Dendrite Electrode for Efficient Electrochemical Reduction of CO2.

Science.gov (United States)

Won, Da Hye; Choi, Chang Hyuck; Chung, Jaehoon; Chung, Min Wook; Kim, Eun-Hee; Woo, Seong Ihl

2015-09-21

Catalysis is a key technology for the synthesis of renewable fuels through electrochemical reduction of CO2 . However, successful CO2 reduction still suffers from the lack of affordable catalyst design and understanding the factors governing catalysis. Herein, we demonstrate that the CO2 conversion selectivity on Sn (or SnOx /Sn) electrodes is correlated to the native oxygen content at the subsurface. Electrochemical analyses show that the reduced Sn electrode with abundant oxygen species effectively stabilizes a CO2 (.-) intermediate rather than the clean Sn surface, and consequently results in enhanced formate production in the CO2 reduction. Based on this design strategy, a hierarchical Sn dendrite electrode with high oxygen content, consisting of a multi-branched conifer-like structure with an enlarged surface area, was synthesized. The electrode exhibits a superior formate production rate (228.6 μmol h(-1)  cm(-2) ) at -1.36 VRHE without any considerable catalytic degradation over 18 h of operation. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Applying macromolecular crowding to 3D bioprinting: fabrication of 3D hierarchical porous collagen-based hydrogel constructs.

Science.gov (United States)

Ng, Wei Long; Goh, Min Hao; Yeong, Wai Yee; Naing, May Win

2018-02-27

Native tissues and/or organs possess complex hierarchical porous structures that confer highly-specific cellular functions. Despite advances in fabrication processes, it is still very challenging to emulate the hierarchical porous collagen architecture found in most native tissues. Hence, the ability to recreate such hierarchical porous structures would result in biomimetic tissue-engineered constructs. Here, a single-step drop-on-demand (DOD) bioprinting strategy is proposed to fabricate hierarchical porous collagen-based hydrogels. Printable macromolecule-based bio-inks (polyvinylpyrrolidone, PVP) have been developed and printed in a DOD manner to manipulate the porosity within the multi-layered collagen-based hydrogels by altering the collagen fibrillogenesis process. The experimental results have indicated that hierarchical porous collagen structures could be achieved by controlling the number of macromolecule-based bio-ink droplets printed on each printed collagen layer. This facile single-step bioprinting process could be useful for the structural design of collagen-based hydrogels for various tissue engineering applications.

Bio-mimetic mechanisms of natural hierarchical materials: a review.

Science.gov (United States)

Chen, Qiang; Pugno, Nicola M

2013-03-01

Natural selection and evolution develop a huge amount of biological materials in different environments (e.g. lotus in water and opuntia in desert). These biological materials possess many inspiring properties, which hint scientists and engineers to find some useful clues to create new materials or update the existing ones. In this review, we highlight some well-studied (e.g. nacre shell) and newly-studied (e.g. turtle shell) natural materials, and summarize their hierarchical structures and mechanisms behind their mechanical properties, from animals to plants. These fascinating mechanisms suggest to researchers to investigate natural materials deeply and broadly, and to design or fabricate new bio-inspired materials to serve our life. Copyright © 2012 Elsevier Ltd. All rights reserved.

The facile synthesis of hierarchical NiCoO2 nanotubes comprised ultrathin nanosheets for supercapacitors

Science.gov (United States)

Xu, Xin; Zhou, Han; Ding, Shujiang; Li, Jun; Li, Beibei; Yu, Demei

2014-12-01

Hierarchical NiCoO2 nanosheets nanotubes are successfully prepared by a mild solution method based on the template of polymeric nanotubes (PNT) followed by a thermal annealing treatment. The microstructure and chemical composition of NiCoO2 nanosheets nanotubes are characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET) analyzer, X-ray diffraction (XRD) and Thermogravimetric analysis (TGA). When evaluated as an electrode material for supercapacitors, the results of electrochemical test show that the unique NiCoO2 nanosheets nanotubes exhibit relatively high specific capacitance of 1468, 1352, 1233, 1178, 1020 and 672 F g-1 at the discharge current densities of 2, 4, 8, 10, 20 and 40 A g-1, respectively. They also reveal an excellent cycling stability of 99.2% retention after 3000 cycles at 10 A g-1. The smart nanostructures of the NiCoO2 nanosheets nanotubes make a prominent contribution to the excellent electrochemical performance.

Immobilized anaerobic fermentation for bio-fuel production by Clostridium co-culture.

Science.gov (United States)

Xu, Lei; Tschirner, Ulrike

2014-08-01

Clostridium thermocellum/Clostridium thermolacticum co-culture fermentation has been shown to be a promising way of producing ethanol from several carbohydrates. In this research, immobilization techniques using sodium alginate and alkali pretreatment were successfully applied on this co-culture to improve the bio-ethanol fermentation performance during consolidated bio-processing (CBP). The ethanol yield obtained increased by over 60 % (as a percentage of the theoretical maximum) as compared to free cell fermentation. For cellobiose under optimized conditions, the ethanol yields were approaching about 85 % of the theoretical efficiency. To examine the feasibility of this immobilization co-culture on lignocellulosic biomass conversion, untreated and pretreated aspen biomasses were also used for fermentation experiments. The immobilized co-culture shows clear benefits in bio-ethanol production in the CBP process using pretreated aspen. With a 3-h, 9 % NaOH pretreatment, the aspen powder fermentation yields approached 78 % of the maximum theoretical efficiency, which is almost twice the yield of the untreated aspen fermentation.

Topotactic Transformation Route to Monodisperse β-NaYF4:Ln(3+) Microcrystals with Luminescence Properties.

Science.gov (United States)

Shao, Baiqi; Feng, Yang; Song, Yan; Jiao, Mengmeng; Lü, Wei; You, Hongpeng

2016-02-15

A novel nonorganic wet route for direct synthesis of uniform hexagonal β-NaYF4:Ln(3+) (Ln = Eu, Tb, Ce/Tb, Yb/Er, and Yb/Tm) microcrystals with various morphologies has been developed wherein the intermediate routine cubic-hexagonal (α → β) phase transfer process was avoided. The morphology can be effectively tuned into hexagonal disc, prism, and novel hierarchical architectures by systematically fine manipulating the Na2CO3/F(-) feeding ratio. It has been found that the routine α → β phase transfer for NaYF4 was not detected during the growth, while NaY(CO3)F2 emerged in the initial reaction stage and fast transformed into β-NaYF4 via a novel topotactic transformation behavior. Detailed structural analysis showed that β-NaYF4 preferred the [001] epitaxial growth direction of NaY(CO3)F2 due to the structural matching of [001]NaY(CO3)F2//[0001]β-NaYF4. Besides, the potential application of the as-prepared products as phosphors is emphasized by demonstrating multicolor emissions including downconversion, upconversion, and energy transfer (Ce-Tb) process by lanthanides doping.

Enhancing biochar yield by co-pyrolysis of bio-oil with biomass: impacts of potassium hydroxide addition and air pretreatment prior to co-pyrolysis.

Science.gov (United States)

Veksha, Andrei; Zaman, Waheed; Layzell, David B; Hill, Josephine M

2014-11-01

The influence of KOH addition and air pretreatment on co-pyrolysis (600 °C) of a mixture of bio-oil and biomass (aspen wood) was investigated with the goal of increasing biochar yield. The bio-oil was produced as a byproduct of the pyrolysis of biomass and recycled in subsequent runs. Co-pyrolysis of the biomass with the recycled bio-oil resulted in a 16% mass increase in produced biochar. The yields were further increased by either air pretreatment or KOH addition prior to co-pyrolysis. Air pretreatment at 220 °C for 3 h resulted in the highest mass increase (32%) compared to the base case of pyrolysis of biomass only. No synergistic benefit was observed by combining KOH addition with air pretreatment. In fact, KOH catalyzed reactions that increased the bed temperature resulting in carbon loss via formation of CO and CO2. Copyright © 2014 Elsevier Ltd. All rights reserved.

Microwave absorption enhancement, magnetic coupling and ab initio electronic structure of monodispersed (Mn1-xCox)3O4 nanoparticles

Science.gov (United States)

Zhao, Pengfei; Liang, Chongyun; Gong, Xiwen; Gao, Ran; Liu, Jiwei; Wang, Min; Che, Renchao

2013-08-01

Monodispersed manganese oxide (Mn1-xCox)3O4 (0 nanoparticles, less than 10 nm size, are respectively synthesized via a facile thermolysis method at a rather low temperature, ranging from 90 to 100 °C, without any inertia gas for protection. The influences of the Co dopant content on the critical reaction temperature required for the nanoparticle formation, electronic band structures, magnetic properties, and the microwave absorption capability of (Mn1-xCox)3O4 are comprehensively investigated by means of both experimental and theoretical approaches including powder X-ray diffraction (XRD), electron energy loss spectroscopy (EELS), super conductivity quantum interference device (SQUID) examination, and first-principle simulations. Co is successfully doped into the Mn atomic sites of the (Mn1-xCox)3O4 lattice, which is further confirmed by EELS data acquired from one individual nanoparticle. Therefore, continuous solid solutions of well-crystallized (Mn1-xCox)3O4 products are achieved without any impurity phase or phase separation. With increases in the Co dopant concentration x from 0 to 0.5, the lattice parameters change systemically, where the overall saturation magnetization at 30 K increases due to the more intense coupling of the 3d electrons between Mn and Co, as revealed by simulations. The microwave absorption properties of the (Mn1-xCox)3O4 nanoparticles are examined between 2 and 18 GHz. The maximum absorption peak -11.0 dB of the x = 0 sample is enhanced to -11.5 dB for x = 0.2, -12.7 dB for x = 0.25, -15.6 dB for x = 0.33, and -24.0 dB for x = 0.5 respectively, suggesting the Co doping effects. Our results might provide novel insights into the understanding of the influences of metallic ion doping on the electromagnetic properties of metallic oxide nanomaterials.Monodispersed manganese oxide (Mn1-xCox)3O4 (0 nanoparticles, less than 10 nm size, are respectively synthesized via a facile thermolysis method at a rather low temperature, ranging from 90 to

Preparation of monodisperse curcumin-imprinted polymer by precipitation polymerization and its application for the extraction of curcuminoids from Curcuma longa L.

Science.gov (United States)

Kitabatake, Tomoko; Tabo, Hiromi; Matsunaga, Hisami; Haginaka, Jun

2013-08-01

A monodisperse molecularly imprinted polymer (MIP) for curcumin was first prepared by precipitation polymerization using methacrylamide (MAM) and 4-vinylpyridine as functional co-monomers, divinylbenzene as a crosslinker, and a mixture of acetonitrile and toluene as a porogen. The use of MAM as the co-monomer resulted in the formation of a monodisperse MIP and non-imprinted polymer (NIP). MIP and NIP, respectively, were monodispersed with a narrow particle size distribution (3.3 ± 0.09 and 3.5 ± 0.10 μm). In addition to shape recognition, hydrophobic and hydrogen-bonding interactions affected the retention and molecular-recognition of curcumin on the MIP. The MIP for curcumin could extract curcuminoids (curcumin, demethoxycurcumin, and bisdemethoxycurcumin) in Curcuma longa L.

One-step synthesis of SnCo nanoconfined in hierarchical carbon nanostructures for lithium ion battery anode.

Science.gov (United States)

Qin, Jian; Liu, Dongye; Zhang, Xiang; Zhao, Naiqin; Shi, Chunsheng; Liu, En-Zuo; He, Fang; Ma, Liying; Li, Qunying; Li, Jiajun; He, Chunnian

2017-10-26

A new strategy for the one-step synthesis of a 0D SnCo nanoparticles-1D carbon nanotubes-3D hollow carbon submicrocube cluster (denoted as SnCo@CNT-3DC) hierarchical nanostructured material was developed via a simple chemical vapor deposition (CVD) process with the assistance of a water-soluble salt (NaCl). The adopted NaCl not only acted as a cubic template for inducing the formation of the 3D hollow carbon submicrocube cluster but also provides a substrate for the SnCo catalysts impregnation and CNT growth, ultimately leading to the successful construction of the unique 0D-1D-3D structured SnCo@CNT-3DC during the CVD of C 2 H 2 . When utilized as a lithium-ion battery anode, the SnCo@CNT-3DC composite electrode demonstrated an excellent rate performance and cycling stability for Li-ion storage. Specifically, an impressive reversible capacity of 826 mA h g -1 after 100 cycles at 0.1 A g -1 and a high rate capacity of 278 mA h g -1 even after 1000 cycles at 5 A g -1 were achieved. This remarkable electrochemical performance could be ascribed to the unique hierarchical nanostructure of SnCo@CNT-3DC, which guarantees a deep permeation of electrolytes and a shortened lithium salt diffusion pathway in the solid phase as well as numerous hyperchannels for electron transfer.

Bio-Carbon Accounting for Bio-Oil Co-Processing: ¹⁴C and ¹³C/¹²C

Energy Technology Data Exchange (ETDEWEB)

Mora, Claudia I. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Li, Zhenghua [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Vance, Zachary [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-06-21

This is a powerpoint presentation on bio-carbon accounting for bio-oil co-processing. Because of the overlapping range in the stable C isotope compositions of fossil oils and biooils from C3-type feedstocks, it is widely thought that stable isotopes are not useful to track renewable carbon during co-production. In contrast, our study demonstrates the utility of stable isotopes to: • capture a record of renewable carbon allocation between FCC products of co-processing • record changes in carbon apportionments due to changes in reactor or feed temperature Stable isotope trends as a function of percent bio-oil in the feed are more pronounced when the δ¹³C of the bio-oil endmember differs greatly from the VGO (i.e., it has a C4 biomass source–corn stover, switch grass, Miscanthus, sugarcane– versus a C3 biomass source– pine, wheat, rice, potato), but trends on the latter case are significant for endmember differences of just a few permil. The correlation between measured ¹⁴C and δ¹³C may be useful as an alternative to carbon accounting, but the relationship must first be established for different bio-oil sources.

One-step facile hydrothermal synthesis of Fe2O3@LiCoO2 composite as excellent supercapacitor electrode materials

Science.gov (United States)

Gopi, Chandu V. V. Muralee; Somasekha, A.; Reddy, Araveeti Eswar; Kim, Soo-Kyoung; Kim, Hee-Je

2018-03-01

Herein, for the first time, we demonstrate the fabrication of Fe2O3@LiCoO2 hybrid nanostructures on Ni foam substrate by facile one-step hydrothermal technique. Morphological studies reveal that aggregated Fe2O3 nanoflakes anchored on the surface of sphere-like LiCoO2 nanoflakes. Electrochemical studies are used to examine the performance of the supercapacitor electrodes. The composite Fe2O3@LiCoO2 electrode exhibited excellent electrochemical performance than Fe2O3 and LiCoO2 electrodes, such as a low charge transfer resistance, a high specific capacitance of 489 F g-1 at 5 mA cm-2 and an enhanced capacity retention of 108% over 3000 cycles at 15 mA cm-2. The composite Fe2O3@LiCoO2 holds great promise for electrochemical applications due to well-defined hierarchical morphology, synergetic effect of Fe2O3 and LiCoO2, enhanced electrical conductivity, efficient electrolyte penetration and fast electron transfer.

Bio-inspired CO2 reduction by a rhenium tricarbonyl bipyridine-based catalyst appended to amino acids and peptidic platforms: incorporating proton relays and hydrogen-bonding functional groups.

Science.gov (United States)

Chabolla, S A; Machan, C W; Yin, J; Dellamary, E A; Sahu, S; Gianneschi, N C; Gilson, M K; Tezcan, F A; Kubiak, C P

2017-06-02

Herein, we report a new approach to bio-inspired catalyst design. The molecular catalyst employed in these studies is based on the robust and selective Re(bpy)(CO) 3 Cl-type (bpy = 2,2'-bipyridine) homogeneous catalysts, which have been extensively studied for their ability to reduce CO 2 electrochemically or photochemically in the presence of a photosensitizer. These catalysts can be highly active photocatalysts in their own right. In this work, the bipyridine ligand was modified with amino acids and synthetic peptides. These results build on earlier findings wherein the bipyridine ligand was functionalized with amide groups to promote dimer formation and CO 2 reduction by an alternate bimolecular mechanism at lower overpotential (ca. 250 mV) than the more commonly observed unimolecular process. The bio-inspired catalysts were designed to allow for the incorporation of proton relays to support reduction of CO 2 to CO and H 2 O. The coupling of amino acids tyrosine and phenylalanine led to the formation of two structurally similar Re catalyst/peptide catalysts for comparison of proton transport during catalysis. This article reports the synthesis and characterization of novel catalyst/peptide hybrids by molecular dynamics (MD simulations of structural dynamics), NMR studies of solution phase structures, and electrochemical studies to measure the activities of new bio-inspired catalysts in the reduction of CO 2.

Effects of Co{sup 2+} doping on physicochemical behaviors of hierarchical NiO nanostructure

Energy Technology Data Exchange (ETDEWEB)

Ding, Caihua [Beijing Key Laboratory of Construction Tailorable Advanced Functional Materials and Green Applications, School of Materials Science & Engineering, Beijing Institute of Technology, Beijing, 100081 (China); Gao, WenChao [College of Engineering, Peking University, Beijing, 100871 (China); Zhao, Yongjie, E-mail: zhaoyjpeace@gmail.com [Beijing Key Laboratory of Construction Tailorable Advanced Functional Materials and Green Applications, School of Materials Science & Engineering, Beijing Institute of Technology, Beijing, 100081 (China); Zhao, Yuzhen; Zhou, Heping [State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Tsinghua University, Beijing, 100084 (China); Li, Jingbo; Jin, Haibo [Beijing Key Laboratory of Construction Tailorable Advanced Functional Materials and Green Applications, School of Materials Science & Engineering, Beijing Institute of Technology, Beijing, 100081 (China)

2016-12-30

Highlights: • A series of Co{sup 2+} doped NiO materials were synthesized by a facile hydrothermal method. • Co{sup 2+} doping would bring about a series influence to the as-obtained NiO products. • Hierarchical NiO nanostructure transformed from nanosheets to nanoneedles with Co{sup 2+} doping. • The catalytic properties of NiO were significantly improved via the introduction of Co{sup 2+}. • Excellent catalytic activity was ascribed to the synergistic effect between Co{sup 2+} and NiO. - Abstract: A series of Co{sup 2+} doped NiO materials (Ni{sub 1−x}Co{sub x}O with x = 0, 0.125, 0.25 and 0.5) were synthesized using a facile hydrothermal method followed by a calcination process. The effects of Co{sup 2+} doping on the structural, morphological, magnetic and catalytic properties of NiO were systematically investigated. The results indicated that Co{sup 2+} doping would bring about a series influence to the as-obtained NiO product. The XRD results indicated that within the region of 0 ≤ x ≤ 0.25 the doped products revealed a pure NiO phase. The elementary unit for the hierarchy NiO gradually transformed from nanosheets to nanoneedles with the increase of Co{sup 2+} doping content. As-obtained Co{sup 2+} doped NiO products showed ferromagnetism at room temperature and the magnetization value was increased with the increase of Co{sup 2+} doping content. The catalytic properties of NiO concerning the thermal decomposition of ammonium perchlorate (AP) were significantly improved via the introduction of Co{sup 2+}. The Ni{sub 1−x}Co{sub x}O products with x = 0.25 showed the best catalytic performance to AP, which could decrease the beginning and ending decomposition temperature of AP by 44 and 108 °C. The change of morphology, enhancement of electrical conductivity and the synergistic effect between Co{sup 2+} and NiO were the main factors responsible for the improvement of physicochemical behaviors.

Production of monodisperse respirable aerosols of 241AmO2 and evaluation of in vitro dissolution

International Nuclear Information System (INIS)

Boyd, H.A.; Raabe, O.G.; Peterson, P.K.

1974-01-01

A method is described for production of monodisperse (sigma//sub g/ less than 1.2) particles of 241 AmO 2 for use in inhalation experiments with dogs and rodents. The effects of physical and chemical factors on the production of polydisperse aerosols of 241 AmO 2 were studied and evaluated. The best aerosol was achieved when a suspension of americium hydroxide with 2.5 mg Am/ml at pH = 7.3 was aerosolized and passed through two heating columns in succession, the first at 300 0 C and the second at 1050 0 C. The particles were roughly spherical and had densities near 8 gm/cm 3 ; the aerosol AMAD and sigma/sub g/ were about 1.5 μm and 1.7, respectively. Monodisperse particles were separated and collected with the Lovelace Aerosol Particle Separator (LAPS) and subsequently suspended in deionized water with pH adjusted to 10.2 with NH 3 for nebulization to produce monodisperse aerosols for inhalation exposures. Particles collected on filters during inhalation experiments were used for evaluation of in vitro dissolution rates with two systems and various forms of a lung fluid simulant. The important role of phosphate ions in such dissolution systems was demonstrated, suggesting the potential for the equally important role of free phosphate in retarding dissolution of AmO 2 particles in the lung. (U.S.)

Co_3V_2O_8 Hexagonal Pyramid with Tunable Inner Structure as High Performance Anode Materials for Lithium Ion Battery

International Nuclear Information System (INIS)

Zhang, Qiang; Pei, Jian; Chen, Gang; Bie, Changfeng; Chen, Dahong; Jiao, Yang; Rao, Jiancun

2017-01-01

Co_3V_2O_8 hexagonal pyramid was successfully fabricated via a simple hydrothermal process and subsequent heat treatment. The inner structure of the hexagonal pyramid was further adjusted by controlling the size of Co_7V_4O_1_6(OH)_2(H_2O) precursors. Hierarchical Co_3V_2O_8 hexagonal pyramid with height of 1 μm were orderly constructed from 60–80 nm inter-connected particles, showing numerous interval voids. Benefiting from its unique structure, the as-prepared sample showed higher electrochemical performance as an anode material for lithium-ion batteries than that of another bulk sample with height of 5 μm and adhesive inner structure. When tested at a current density of 500 mA g"−"1, the hierarchical Co_3V_2O_8 hexagonal pyramid exhibited good rate capacity, high cycling stability, and excellent discharge capacity up to 712 mA h g"−"1, making it promising electrode materials for lithium-ion batteries.

Synthesis of raspberry-like monodisperse magnetic hollow hybrid nanospheres by coating polystyrene template with Fe(3)O(4)@SiO(2) particles.

Science.gov (United States)

Wang, Chunlei; Yan, Juntao; Cui, Xuejun; Wang, Hongyan

2011-02-01

In this paper, we present a novel method for the preparation of raspberry-like monodisperse magnetic hollow hybrid nanospheres with γ-Fe(2)O(3)@SiO(2) particles as the outer shell. PS@Fe(3)O(4)@SiO(2) composite nanoparticles were successfully prepared on the principle of the electrostatic interaction between negatively charged silica and positively charged polystyrene, and then raspberry-like magnetic hollow hybrid nanospheres with large cavities were achieved by means of calcinations, simultaneously, the magnetite (Fe(3)O(4)) was transformed into maghemite (γ-Fe(2)O(3)). Transmission electron microscopy (TEM) demonstrated that the obtained magnetic hollow silica nanospheres with the perfect spherical profile were well monodisperse and uniform with the mean size of 253nm. The Fourier transform infrared (FTIR) spectrometry, energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) provided the sufficient evidences for the presence of Fe(3)O(4) in the silica shell. Moreover, the magnetic hollow silica nanospheres possessed a characteristic of superparamagnetic with saturation magnetization value of about 7.84emu/g by the magnetization curve measurement. In addition, the nitrogen adsorption-desorption measurement exhibited that the pore size, BET surface area, pore volume of magnetic hollow silica nanospheres were 3.5-5.5nm, 307m(2)g(-1) and 1.33cm(3)g(-1), respectively. Therefore, the magnetic hollow nanospheres possess a promising future in controlled drug delivery and targeted drug applications. Copyright © 2010 Elsevier Inc. All rights reserved.

Hierarchical Co-based Porous Layered Double Hydroxide Arrays Derived via Alkali Etching for High-performance Supercapacitors

Science.gov (United States)

Abushrenta, Nasser; Wu, Xiaochao; Wang, Junnan; Liu, Junfeng; Sun, Xiaoming

2015-08-01

Hierarchical nanoarchitecture and porous structure can both provide advantages for improving the electrochemical performance in energy storage electrodes. Here we report a novel strategy to synthesize new electrode materials, hierarchical Co-based porous layered double hydroxide (PLDH) arrays derived via alkali etching from Co(OH)2@CoAl LDH nanoarrays. This structure not only has the benefits of hierarchical nanoarrays including short ion diffusion path and good charge transport, but also possesses a large contact surface area owing to its porous structure which lead to a high specific capacitance (23.75 F cm-2 or 1734 F g-1 at 5 mA cm-2) and excellent cycling performance (over 85% after 5000 cycles). The enhanced electrode material is a promising candidate for supercapacitors in future application.

The potential of near-surface geophysical methods in a hierarchical monitoring approach for the detection of shallow CO2 seeps at geological storage sites

Science.gov (United States)

Sauer, U.; Schuetze, C.; Dietrich, P.

2013-12-01

The MONACO project (Monitoring approach for geological CO2 storage sites using a hierarchic observation concept) aims to find reliable monitoring tools that work on different spatial and temporal scales at geological CO2 storage sites. This integrative hierarchical monitoring approach based on different levels of coverage and resolutions is proposed as a means of reliably detecting CO2 degassing areas at ground surface level and for identifying CO2 leakages from storage formations into the shallow subsurface, as well as CO2 releases into the atmosphere. As part of this integrative hierarchical monitoring concept, several methods and technologies from ground-based remote sensing (Open-path Fourier-transform infrared (OP-FTIR) spectroscopy), regional measurements (near-surface geophysics, chamber-based soil CO2 flux measurement) and local in-situ measurements (using shallow boreholes) will either be combined or used complementary to one another. The proposed combination is a suitable concept for investigating CO2 release sites. This also presents the possibility of adopting a modular monitoring concept whereby our monitoring approach can be expanded to incorporate other methods in various coverage scales at any temporal resolution. The link between information obtained from large-scale surveys and local in-situ monitoring can be realized by sufficient geophysical techniques for meso-scale monitoring, such as geoelectrical and self-potential (SP) surveys. These methods are useful for characterizing fluid flow and transport processes in permeable near-surface sedimentary layers and can yield important information concerning CO2-affected subsurface structures. Results of measurements carried out a natural analogue site in the Czech Republic indicate that the hierarchical monitoring approach represents a successful multidisciplinary modular concept that can be used to monitor both physical and chemical processes taking place during CO2 migration and seepage. The

First assessment of Li2O–Bi2O3 ceramic oxides for high temperature carbon dioxide capture简

Institute of Scientific and Technical Information of China (English)

E.M.Briz-López; M.J.Ramírez-Moreno; I.C.Romero-Ibarra; C.Gómez-Yá?ez; H.Pfeiffer; J.Ortiz-Landeros

2016-01-01

The capacity to capture CO2 was determined in several stoichiometric compositions in the Li2O–Bi2O3 system. The compounds（Li7BiO6, Li5BiO5, Li3BiO4 and LiBiO2 phases） were synthesized via solid-state reaction and characterized by X-ray diffraction, scanning electron microscopy and N2 adsorption techniques.The samples were heat-treated at temperatures from 40 to 750 °C under the CO2 atmosphere to evaluate the carbonate formation, which is indicative of the capacity of CO2 capture. Moreover, Li7BiO6 shows an excellent CO2 capture capacity of 7.1 mmol/g, which is considerably higher than those of other previously reported ceramics. Li7BiO6 is able to react with CO2 from 240 °C to approximately 660 °C showing a high kinetic reaction even at CO2 partial pressure values as low as 0.05.

In-situ preparation of Fe2O3 hierarchical arrays on stainless steel substrate for high efficient catalysis

International Nuclear Information System (INIS)

Yang, Zeheng; Wang, Kun; Shao, Zongming; Tian, Yuan; Chen, Gongde; Wang, Kai; Chen, Zhangxian; Dou, Yan; Zhang, Weixin

2017-01-01

Hierarchical array catalysts with micro/nano structures on substrates not only possess high reactivity from large surface area and suitable interface, but intensify mass transfer through shortening the diffusion paths of both reactants and products for high catalytic efficiency. Herein, we first demonstrate fabrication of Fe 2 O 3 hierarchical arrays grown on stainless-steel substrates via in-situ hydrothermal chemical oxidation followed by heat treatment in N 2 atmosphere. As a Fenton-like catalyst, Fe 2 O 3 hierarchical arrays exhibit excellent catalytic activity and life cycle performance for methylene blue (MB) dye degradation in aqueous solution in the presence of H 2 O 2 . The Fe 2 O 3 catalyst with unique hierarchical structures and efficient transport channels, effectively activates H 2 O 2 to generate large quantity of • OH radicals and highly promotes reaction kinetics between MB and • OH radicals. Immobilization of hierarchical array catalysts on stainless-steel can prevent particles agglomeration, facilitate the recovery and reuse of the catalysts, which is expected promising applications in wastewater remediation. - Graphical abstract: The in-situ synthesis of Fe 2 O 3 hierarchical arrays on stainless-steel substrates was reported for the first time, which exhibit excellent catalytic activity performance for methylene blue (MB) dye degradation in aqueous solution in the presence of H 2 O 2 . - Highlights: • Fe 2 O 3 hierarchical arrays was prepared by in-situ hydrothermal chemical oxidation. • F − ions play an important role in the formation of the Fe 2 O 3 hierarchical arrays. • Fe 2 O 3 hierarchical arrays show high catalytic activity to methylene blue degradation.

Bio-MTBE. How to reduce CO{sub 2} footprint in fuels with a well known premium gasoline component

Energy Technology Data Exchange (ETDEWEB)

Busch, O.; Schade, A.; Rasch, H.; Schulte-Koerne, E. [Evonik Industries AG, Marl (Germany)

2012-07-01

With the revision of Renewable Energy Directive (RED) and Fuels Quality Directive (FQD) in 2009 the EU Commission promoted the use of biofuels, especially of those made from residues and waste because of their favourable CO{sub 2} footprint. Crude glycerol is an inevitable residue of conventional biodiesel production and can therefore be used to make 2{sup nd} generation biofuels, in this case bio-methanol. Methanol itself has several application issues as a fuel and can only be blended into gasoline at low quantities (max. 3 vol.-% according to European gasoline specification EN 228). However, today methanol is virtually absent in European gasoline due to its detrimental properties (e.g. corrosivity, water miscibility, etc.). In contrast to this, MTBE (methyl tertiary butyl ether) made from methanol and isobutylene is a high value gasoline component that can be blended into gasoline at high quantities without any application issues. Current European gasoline specification allows up to 15 vol.-%% and the revised FQD has enabled the specification to be expanded to up to 22 vol.-% MTBE in gasoline. Thus, bio-methanol converted into bio-MTBE is an appropriate pathway to get a 2{sup nd} generation biofuel into the blending pool with perfect compatibility with infrastructure and the existing car fleet. (orig.)

The reflection of hierarchical cluster analysis of co-occurrence matrices in SPSS

NARCIS (Netherlands)

Zhou, Q.; Leng, F.; Leydesdorff, L.

2015-01-01

Purpose: To discuss the problems arising from hierarchical cluster analysis of co-occurrence matrices in SPSS, and the corresponding solutions. Design/methodology/approach: We design different methods of using the SPSS hierarchical clustering module for co-occurrence matrices in order to compare

Annealing effect on the structural and optical properties of Cr/α-Cr2O3 monodispersed particles based solar absorbers

International Nuclear Information System (INIS)

Khamlich, S.; McCrindle, R.; Nuru, Z.Y.; Cingo, N.; Maaza, M.

2013-01-01

Graphical abstract: A cost-effective and environmentally friendly green chemical method, the so-called aqueous chemical growth (ACG) method, was used to deposit chromium/alpha-chromium(III) oxide, Cr/α-Cr 2 O 3 , monodispersed particles, for solar absorbers applications. Highlights: ► Cr/α-Cr 2 O 3 have been deposited by the aqueous chemical growth (ACG) method. ► High temperature annealing affects the optical selectivity of the deposited particles. ► Oxygen diffusion to the interface at high temperature results in the oxidization of the substrate. - Abstract: A cost-effective and environmentally friendly green chemical method, the so-called aqueous chemical growth (ACG) method, was used to deposit chromium/alpha-chromium(III) oxide, Cr/α-Cr 2 O 3 , monodispersed particles, for solar absorbers applications. The deposited particles were annealed at various temperatures in a hydrogen atmosphere for 2 h to study the annealing temperature dependence of the structural, chemical and optical properties of the particles grown on tantalum substrates. The deposited Cr/α-Cr 2 O 3 was characterized by X-ray diffraction (XRD), attenuated total reflection (ATR), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), and diffuse reflectance UV–vis–NIR spectroscopy. The XRD and ATR analysis indicated that by increasing annealing temperature, the particles crystallinity was improved and Ta 2 O 5 was formed around 600 °C, due to the fast oxygen diffusion from the deposited α-Cr 2 O 3 toward the tantalum substrate. The optical measurements show that samples annealed at 400 and 500 °C exhibit the targeted high absorbing optical characteristics of “Black chrome”, while those annealed below 400 °C and above 500 °C show a significant low absorptivity and high emissivity.

Hierarchical CNFs/MnCo2O4.5 nanofibers as a highly active oxidase mimetic and its application in biosensing

Science.gov (United States)

Gao, Mu; Lu, Xiaofeng; Nie, Guangdi; Chi, Maoqiang; Wang, Ce

2017-12-01

Recently, much attention has been paid on the nanomaterial-based artificial enzymes due to their tunable catalytic activity, high stability and low cost compared to the natural enzymes. Different from the peroxidase mimics which have been studied for several decades, nanomaterials with oxidase-like property are burgeoning in the recent years. In this paper, hierarchical carbon nanofibers (CNFs)/MnCo2O4.5 nanofibers as efficient oxidase mimics are reported. The products are synthesized by an electrospinning technique and an electrochemcial deposition process in which the CNFs are used as the working electrode where MnCo2O4.5 nanosheets deposit on. The resulting binary metal oxide-based nanocomposites exhibit a good oxidase-like activity toward the oxidations of 3,3‧,5,5‧tetramethylbenzi-dine (TMB), 2,2‧-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) diammonium (ABTS) salt and o-phenylenediamine (OPD) without exogenous addition of H2O2. The system of CNFs/MnCo2O4.5-TMB can be used as a candidate to detect sulfite and ascorbic acid via a colorimetric method with a high sensitivity. This work provides the efficient utilization and potential applications of binary metal oxide-based nanocomposites with oxidase activities in biosensors and other biotechnologies.

Facile Fabrication of 3D Hierarchically Porous Carbon Foam as Supercapacitor Electrode Material

Directory of Open Access Journals (Sweden)

Yunfang Gao

2018-04-01

Full Text Available A hierarchically porous 3D starch-derived carbon foam (SCF with a high specific surface area (up to 1693 m2·g−1 was first prepared by a facile solvothermal treatment, in which Na2CO3 is used as both the template and activating agent. The hierarchically porous structure and high specific area endow the SCF with favorable electrochemical properties such as a high specific capacitance of 179.6 F·g−1 at 0.5 A·g−1 and a great rate capability and cycling stability, which suggest that the material can be a promising candidate for energy storage applications.

Ultrathin mesoporous Co_3O_4 nanosheets-constructed hierarchical clusters as high rate capability and long life anode materials for lithium-ion batteries

International Nuclear Information System (INIS)

Wu, Shengming; Xia, Tian; Wang, Jingping; Lu, Feifei; Xu, Chunbo; Zhang, Xianfa; Huo, Lihua; Zhao, Hui

2017-01-01

Graphical abstract: Ultrathin mesoporous Co_3O_4 nanosheets-constructed hierarchical clusters (UMCN-HCs) have been successfully synthesized via a facile hydrothermal method followed by a subsequent thermolysis treatment. When tested as anode materials for LIBs, UMCN-HCs achieve high reversible capacity, good long cycling life, and rate capability. - Highlights: • UMCN-HCs show high capacity, excellent stability, and good rate capability. • UMCN-HCs retain a capacity of 1067 mAh g"−"1 after 100 cycles at 100 mA g"−"1. • UMCN-HCs deliver a capacity of 507 mAh g"−"1 after 500 cycles at 2 A g"−"1. - Abstract: Herein, Ultrathin mesoporous Co_3O_4 nanosheets-constructed hierarchical clusters (UMCN-HCs) have been successfully synthesized via a facile hydrothermal method followed by a subsequent thermolysis treatment at 600 °C in air. The products consist of cluster-like Co_3O_4 microarchitectures, which are assembled by numerous ultrathin mesoporous Co_3O_4 nanosheets. When tested as anode materials for lithium-ion batteries, UMCN-HCs deliver a high reversible capacity of 1067 mAh g"−"1 at a current density of 100 mA g"−"1 after 100 cycles. Even at 2 A g"−"1, a stable capacity as high as 507 mAh g"−"1 can be achieved after 500 cycles. The high reversible capacity, excellent cycling stability, and good rate capability of UMCN-HCs may be attributed to their mesoporous sheet-like nanostructure. The sheet-layered structure of UMCN-HCs may buffer the volume change during the lithiation-delithiation process, and the mesoporous characteristic make lithium-ion transfer more easily at the interface between the active electrode and the electrolyte.

Effect of Ni/Al2O3-SiO2 and Ni/Al2O3-SiO2 with K2O Promoter Catalysts on H2, CO and CH4 Concentration by CO2 Gasification of Rosa Multiflora Biomass

Directory of Open Access Journals (Sweden)

Tursunov Obid

2017-11-01

Full Text Available The thermal behaviour of the Rosa mutiflora biomass by thermogravimetric analysis was studied at heating rate 3 K min−1 from ambient temperature to 950 °C. TGA tests were performed in high purity carbon dioxide (99 998% with a flow rate 200 ml/min and 100 mg of sample, milled and sieved to a particle size below 250 µm. Moreover, yields of gasification products such as hydrogen (H2, carbon monoxide (CO and methane (CH4 were determined based on the thermovolumetric measurements of catalytic (Ni/Al2O3-SiO2 and Ni/Al2O3-SiO2 with K2O promoter catalysts and non-catalytic gasification of the Rosa multiflora biomass. Additionally, carbon conversion degrees are presented. Calculations were made of the kinetic parameters of carbon monoxide and hydrogen formation reaction in the catalytic and non-catalytic CO2 gasification processes. A high temperature of 950 °C along with Ni/Al2O3-SiO2and Ni/Al2O3-SiO2 with K2O promoter catalysts resulted in a higher conversion of Rosa multiflora biomass into gaseous yield production with greatly increasing of H2 and CO contents. Consequently, H2 and CO are the key factors to produce renewable energy and bio-gases (synthesis gas. The parameters obtained during the experimental examinations enable a tentative assessment of plant biomasses for the process of large-scale gasification in industrial sectors.

Ultra-Low Carbon Emissions from Coal-Fired Power Plants through Bio-Oil Co-Firing and Biochar Sequestration.

Science.gov (United States)

Dang, Qi; Mba Wright, Mark; Brown, Robert C

2015-12-15

This study investigates a novel strategy of reducing carbon emissions from coal-fired power plants through co-firing bio-oil and sequestering biochar in agricultural lands. The heavy end fraction of bio-oil recovered from corn stover fast pyrolysis is blended and co-fired with bituminous coal to form a bio-oil co-firing fuel (BCF). Life-cycle greenhouse gas (GHG) emissions per kWh electricity produced vary from 1.02 to 0.26 kg CO2-eq among different cases, with BCF heavy end fractions ranging from 10% to 60%, which corresponds to a GHG emissions reduction of 2.9% to 74.9% compared with that from traditional bituminous coal power plants. We found a heavy end fraction between 34.8% and 37.3% is required to meet the Clean Power Plan's emission regulation for new coal-fired power plants. The minimum electricity selling prices are predicted to increase from 8.8 to 14.9 cents/kWh, with heavy end fractions ranging from 30% to 60%. A minimum carbon price of $67.4 ± 13 per metric ton of CO2-eq was estimated to make BCF power commercially viable for the base case. These results suggest that BCF co-firing is an attractive pathway for clean power generation in existing power plants with a potential for significant reductions in carbon emissions.

Colloidal processing and CO_2-capture performance Al_2O_3-zeolite 13X composites

International Nuclear Information System (INIS)

Andersson, L.; Akhtar, F.; Ojuva, A.; Bergstroem, L.

2012-01-01

Hierarchically porous composites for CO_2-capture have been produced by coating the inner walls of foam-like macroporous alumina monoliths, produced by templated synthesis, with microporous zeolite 13X particles. Homogeneous and dense coatings of the particulate adsorbent were obtained when the impregnation process was performed at a pH above 9. At this pH-level the colloidally stable suspensions of the negatively charged zeolite 13X particles could fill all the voids of the highly connected pore space of the alumina supports and attach to the monolith walls, which had been pre-coated with poly(ethylene imine). A CO_2-uptake as high as 5 mmol CO_2/g zeolite 13X was achieved for alumina-zeolite 13X composites through minimisation of the added inorganic binder, kaolin, to only 3.0 wt% with respect to zeolite content, and through optimisation of the thermal treatment.

The bio-energies development: the role of biofuels and the CO2 price

International Nuclear Information System (INIS)

Jouvet, Pierre-Andre; Lantz, Frederic; Le Cadre, Elodie

2012-01-01

Reduction in energy dependency and emissions of CO 2 via renewable energies targeted in the European Union energy mix and taxation system, might trigger the production of bio-energy production and competition for biomass utilization. Torrefied biomass could be used to produce second generation biofuels to replace some of the fuels used in transportation and is also suitable as feedstock to produce electricity in large quantities. This paper examines how the CO 2 price affects demand of torrefied biomass in the power sector and its consequences on the profitability of second generation biofuel units (Biomass to Liquid units). Indeed, the profitability of the BtL units which are supplied only by torrefied biomass is related to the competitive demand of the power sector driven by the CO 2 price and feed-in tariffs. We propose a linear dynamic model of supply and demand. On the supply side, a profit-maximizing torrefied biomass sector is modelled. The model aims to represent the transformation of biomass into torrefied biomass which could be sold to the refinery sector and the power sector. A two-sided (demanders and supplier) bidding process led us to arrive at the equilibrium price for torrefied biomass. The French case is used as an example. Our results suggest that the higher the CO 2 price, the more stable and important the power sector demand. It also makes the torrefied biomass production less vulnerable to uncertainty on demand coming from the refining sector. The torrefied biomass co-firing with coal can offer a near-term market for the torrefied biomass for a CO 2 emission price lower than 20 euros/tCO 2 , which can stimulate development of biomass supply systems. Beyond 2020, the demand for torrefied biomass from the power sector could be substituted by the refining sector if the oil price goes up whatever the CO 2 price. (authors)

Photoelectrochemical properties of hierarchical ZnO micro-nanostructure sensitized with Sb2S3 nanoparticles

Directory of Open Access Journals (Sweden)

Zhimin GUO

2016-02-01

Full Text Available By using electrochemical deposition method, and assisted with additions of PEG-400 and EDA, well-aligned ZnO nanorods and hierarchical ZnO micro-nanostructure are fabricated directly on indium doped tin oxide coated conducting glass (ITO substrate. The shell-core Sb2S3/ZnO nanorod structure and the shell-core hierarchical Sb2S3/ZnO micro-nanostructure are prepared by chemical bath deposition method. SEM, XRD, UV-Vis and photocurrent test are used to characterize the morphology, nanostructures and their photoelectrochemical properties. The studies show that the photocurrent on the array membranes with shell-core hierarchical Sb2S3/ZnO micro-nanostructure is apparently higher than that with shell-core Sb2S3/ZnO nanorods array.

A quantum cascade laser infrared spectrometer for CO2 stable isotope analysis: Field implementation at a hydrocarbon contaminated site under bio-remediation.

Science.gov (United States)

Guimbaud, Christophe; Noel, Cécile; Chartier, Michel; Catoire, Valéry; Blessing, Michaela; Gourry, Jean Christophe; Robert, Claude

2016-02-01

Real-time methods to monitor stable isotope ratios of CO2 are needed to identify biogeochemical origins of CO2 emissions from the soil-air interface. An isotope ratio infra-red spectrometer (IRIS) has been developed to measure CO2 mixing ratio with δ(13)C isotopic signature, in addition to mixing ratios of other greenhouse gases (CH4, N2O). The original aspects of the instrument as well as its precision and accuracy for the determination of the isotopic signature δ(13)C of CO2 are discussed. A first application to biodegradation of hydrocarbons is presented, tested on a hydrocarbon contaminated site under aerobic bio-treatment. CO2 flux measurements using closed chamber method is combined with the determination of the isotopic signature δ(13)C of the CO2 emission to propose a non-intrusive method to monitor in situ biodegradation of hydrocarbons. In the contaminated area, high CO2 emissions have been measured with an isotopic signature δ(13)C suggesting that CO2 comes from petroleum hydrocarbon biodegradation. This first field implementation shows that rapid and accurate measurement of isotopic signature of CO2 emissions is particularly useful in assessing the contribution of contaminant degradation to the measured CO2 efflux and is promising as a monitoring tool for aerobic bio-treatment. Copyright © 2016. Published by Elsevier B.V.

Hierarchical core-shell NiCo2O4@NiMoO4 nanowires grown on carbon cloth as integrated electrode for high-performance supercapacitors

Science.gov (United States)

Huang, Liang; Zhang, Wei; Xiang, Jinwei; Xu, Henghui; Li, Guolong; Huang, Yunhui

2016-08-01

Hierarchical core-shell NiCo2O4@NiMoO4 nanowires were grown on carbon cloth (CC@NiCo2O4@NiMoO4) by a two-step hydrothermal route to fabricate a flexible binder-free electrode. The prepared CC@NiCo2O4@NiMoO4 integrated electrode was directly used as an electrode for faradaic supercapacitor. It shows a high areal capacitance of 2.917 F cm-2 at 2 mA cm-2 and excellent cycling stability with 90.6% retention over 2000 cycles at a high current density of 20 mA cm-2. The superior specific capacitance, rate and cycling performance can be ascribed to the fast transferring path for electrons and ions, synergic effect and the stability of the hierarchical core-shell structure.

Hydrothermal synthesis and photoluminescent properties of hierarchical GdPO4·H2O:Ln3+ (Ln3+ = Eu3+, Ce3+, Tb3+) flower-like clusters

Science.gov (United States)

Amurisana, Bao.; Zhiqiang, Song.; Haschaolu, O.; Yi, Chen; Tegus, O.

2018-02-01

3D hierarchical GdPO4·H2O:Ln3+ (Ln3+ = Eu3+, Ce3+, Tb3+) flower clusters were successfully prepared on glass slide substrate by a simple, economical hydrothermal process with the assistance of disodium ethylenediaminetetraacetic acid (Na2H2L, where L4- = (CH2COO)2N(CH2)2N(CH2COO)24-). In this process, Na2H2L was used as both a chelating agent and a structure-director. The hierarchical flower clusters have an average diameter of 7-12 μm and are composed of well-aligned microrods. The influence of the molar ratio of Na2H2L/Gd3+ and reaction time on the morphology was systematically studied. A possible crystal growth and formation mechanism of hierarchical flower clusters is proposed based on the evolution of morphology as a function of reaction time. The self-assembled GdPO4·H2O:Ln3+ superstructures exhibit strong orange-red (Eu3+, 5D0 → 7F1), green (Tb3+, 5D4 → 7F5) and near ultraviolet emissions (Ce3+, 5d → 7F5/2) under ultraviolet excitation, respectively. This study may provide a new channel for building hierarchically superstructued oxide micro/nanomaterials with optical and new properties.

Syntrophic co-culture of aerobic Bacillus and anaerobic Clostridium for bio-fuels and bio-hydrogen production

Energy Technology Data Exchange (ETDEWEB)

Chang, Jui-Jen; Ho, Cheng-Yu.; Chen, Wei-En; Huang, Chieh-Chen [Department of Life Sciences, National Chung Hsing University, Taichung (China); Chou, Chia-Hung; Lay, Jiunn-Jyi [Department of Science and Technology, National Kaohsiung First University, Kaohsiung (China)

2008-10-15

By using brewery yeast waste and microflora from rice straw compost, an anaerobic semi-solid bio-hydrogen-producing system has been established. For the purpose of industrialization, the major players of both aerobic and anaerobic bacterial strains in the system were isolated and their combination for an effective production of bio-hydrogen and other bio-fuels was examined in this study. The phylogenetic analysis found that four anaerobic isolates (Clostridium beijerinckii L9, Clostridium diolis Z2, Clostridium roseum Z5-1, and C. roseum W8) were highly related with each other and belongs to the cluster I clostridia family, the family that many of solvent-producing strains included. On the other hand, one of the aerobic isolates, the Bacillus thermoamylovorans strain I, shown multiple extracellular enzyme activities including lipase, protease, {alpha}-amylase, pectinase and cellulase, was suggested as a good partner for creating an anaerobic environment and pre-saccharification of substrate for those co-cultured solventogenic clostridial strain. Among these clostridial strains, though C. beijerinckii L9 do not show as many extracellular enzyme activities as Bacillus, but it performs the highest hydrogen-producing ability. The original microflora can be updated to a syntrophic bacterial co-culture system contended only with B. thermoamylovorans I and C. beijerinckii L9. The combination of aerobic Bacillus and anaerobic Clostridium may play the key role for developing the industrialized bio-fuels and bio-hydrogen-producing system from biomass. (author)

Hierarchically MnO2-Nanosheet Covered Submicrometer-FeCo2O4-Tube Forest as Binder-Free Electrodes for High Energy Density All-Solid-State Supercapacitors.

Science.gov (United States)

Zhu, Baogang; Tang, Shaochun; Vongehr, Sascha; Xie, Hao; Meng, Xiangkang

2016-02-01

The current problem of the still relatively low energy densities of supercapacitors can be effectively addressed by designing electrodes hierarchically on micro- and nanoscale. Herein, we report the synthesis of hierarchically porous, nanosheet covered submicrometer tube forests on Ni foam. Chemical deposition and thermal treatment result in homogeneous forests of 750 nm diameter FeCo2O4 tubes, which after hydrothermal reaction in KMnO4 are wrapped in MnO2-nanosheet-built porous covers. The covers' thickness can be adjusted from 200 to 800 nm by KMnO4 concentration. An optimal thickness (380 nm) with a MnO2 content of 42 wt % doubles the specific capacitance (3.30 F cm(-2) at 1.0 mA cm(-2)) of the bare FeCo2O4-tube forests. A symmetric solid-state supercapacitor made from these binder-free electrodes achieves 2.52 F cm(-2) at 2 mA cm(-2), much higher than reported for capacitors based on similar core-shell nanowire arrays. The large capacitance and high cell voltage of 1.7 V allow high energy and power densities (93.6 Wh kg(-1), 10.1 kW kg(-1)). The device also exhibits superior rate capability (71% capacitance at 20 mA cm(-2)) and remarkable cycling stability with 94% capacitance retention being stable after 1500 cycles.

Upgrading pyrolysis bio-oil to biofuel over bifunctional Co-Zn/HZSM-5 catalyst in supercritical methanol

International Nuclear Information System (INIS)

Cheng, Shouyun; Wei, Lin; Julson, James; Muthukumarappan, Kasiviswanathan; Kharel, Parashu Ram

2017-01-01

Highlights: • Integration of Co-Zn/HZSM-5 and supercritical methanol was used for bio-oil hydrodeoxygenation. • Co-Zn/HZSM-5 exhibited higher effectiveness than Co/HZSM-5 or Zn/HZSM-5. • 15%Co5%Zn/HZSM-5 produced biofuel with the highest hydrocarbons content at 35.33%. • Loading of Co and/or Zn did not change crystalline structure of HZSM-5. • Hydrogenation and esterification are main reactions in bio-oil hydrodeoxygenation. - Abstract: The role of catalyst is essential in processes of upgrading biomass pyrolysis bio-oil into hydrocarbon biofuel. While the majority of heterogeneous catalytic processes are conducted in the presence of gas (nearly ideal) or liquid phase, a growing number of processes are utilizing supercritical fluids (SCFs) as reaction media. Although hydrodeoxygenation (HDO) is proven a promising process for pyrolysis bio-oil upgrading to hydrocarbon biofuel, catalyst efficiency remains a challenge. Integrating heterogeneous catalysts with SCFs in a bio-oil HDO process was investigated in this study. Bifunctional Co-Zn/HZSM-5 catalysts were firstly used to upgrade bio-oil to biofuel in supercritical methanol. The loading of Co and Zn did not change HZSM-5 crystalline structure. Physicochemical properties of biofuel produced by Co and/or Zn loaded HZSM-5 catalysts such as water content, total acid number, viscosity and higher heating value improved. Bimetallic Co-Zn/HZSM-5 catalysts showed enhanced reactions of decarboxylation and decarbonylation that resulted in higher yields of CO and CO 2 . Bimetallic Co-Zn/HZSM-5 catalysts were more effective for bio-oil HDO than monometallic Co/HZSM-5 or Zn/HZSM-5 catalyst , which was attributed to the synergistic effect of Co and Zn on HZSM-5 support. Bimetallic Co-Zn/HZSM-5 catalysts increased biofuel yields and hydrocarbons contents in biofuels in comparison with monometallic Co/HZSM-5 and Zn/HZSM-5 catalysts. 5%Co15%Zn/HZSM-5 catalyst generated the highest biofuel yield at 22.13 wt.%, and 15%Co5

Beneficial synergistic effect on bio-oil production from co-liquefaction of sewage sludge and lignocellulosic biomass.

Science.gov (United States)

Leng, Lijian; Li, Jun; Yuan, Xingzhong; Li, Jingjing; Han, Pei; Hong, Yuchun; Wei, Feng; Zhou, Wenguang

2018-03-01

Co-liquefaction of municipal sewage sludge (MSS) and lignocellulosic biomass such as rice straw or wood sawdust at different mixing ratios and the characterization of the obtained bio-oil and bio-char were investigated. Synergistic effects were found during co-processing of MSS with biomass for production of bio-oil with higher yield and better fuel properties than those from individual feedstock. The co-liquefaction of MSS/rice straw (4/4, wt) increased the bio-oil yield from 22.74% (bio-oil yield from liquefaction of MSS individually) or 23.67% (rice straw) to 32.45%. Comparable increase on bio-oil yield was also observed for MSS/wood sawdust mixtures (2/6, wt). The bio-oils produced from MSS/biomass mixtures were mainly composed of esters and phenols with lower boiling points (degradation temperatures) than those from individual feedstock (identified with higher heavy bio-oil fractions). These synergistic effects were probably resulted from the interactions between the intermittent products of MSS and those of biomass during processing. Copyright © 2017 Elsevier Ltd. All rights reserved.

A facile approach for the synthesis of monolithic hierarchical porous carbons – high performance materials for amine based CO2 capture and supercapacitor electrode

KAUST Repository

Estevez, Luis

2013-05-03

An ice templating coupled with hard templating and physical activation approach is reported for the synthesis of hierarchically porous carbon monoliths with tunable porosities across all three length scales (macro- meso- and micro), with ultrahigh specific pore volumes [similar]11.4 cm3 g−1. The materials function well as amine impregnated supports for CO2 capture and as supercapacitor electrodes.

Synthesis of Monodisperse Iron Oxide Nanoparticles without Surfactants

Directory of Open Access Journals (Sweden)

Xiao-Chen Yang

2014-01-01

Full Text Available Monodisperse iron oxide nanoparticles could be successfully synthesized with two kinds of precipitants through a precipitation method. As-prepared nanoparticles in the size around 10 nm with regular spherical-like shape were achieved by adjusting pH values. NaOH and NH3·H2O were used as two precipitants for comparison. The average size of nanoparticles with NH3·H2O precipitant got smaller and represented better dispersibility, while nanoparticles with NaOH precipitant represented better magnetic property. This work provided a simple method without using any organic solvents, organic metal salts, or surfactants which could easily obtain monodisperse nanoparticles with tunable morphology.

Solubility of NaNd(CO3)2.6H2O(c) in concentrated Na2CO3 and NaHCO3 solutions

International Nuclear Information System (INIS)

Rao, L.; Rai, D.; Felmy, A.R.; Fulton, R.W.; Novak, C.F.

1996-01-01

NaNd(CO 3 ) 2 x 6 H 2 O(c) was identified to be the final equilibrium solid phase in suspensions containing concentrated sodium carbonate (0.1 to 2.0 M) and sodium bicarbonate (0.1 to 1.0 M), with either NaNd(CO 3 ) 2 x 6 H 2 O(c) or Nd 2 (CO 3 ) 3 x xH 2 O(s) as initial solids. A thermodynamic model, based on Pitzer's specific into-interaction approach, was developed to interpret the solubility of NaNd(CO 3 ) 2 x 6 H 2 O(c) as functions of sodium carbonate and sodium bicarbonate concentrations. In this model, the solubility data of NaNd(CO 3 ) 2 x 6 H 2 O(c) were explained by assuming the formation of NdCO 3 + , Nd(CO 3 ) 2 - and Nd(CO 3 ) 3 3- species and invoking the specific ion interactions between Na + and Nd(CO 3 ) 3 3- . Ion interaction parameters for Na + -Nd(CO 3 ) 3 3- were developed to fit the solubility data. Based on the model calculations, Nd(CO 3 ) 3 3- was the predominant aqueous neodymium species in 0.1 to 2 M sodium carbonate and 0.1 to 1 M sodium bicarbonate solutions. The logarithm of the NaNd(CO 3 ) 2 x 6 H 2 O solubility product (NaNd(CO 3 ) 2 x 6 H 2 O(c)=Na + +Nd 3+ +2 CO 3 2- +6 H 2 O) was calculated to be -21.39. This model also provided satisfactory interpretation of the solubility data of the analogous Am(III) system in less concentrated carbonate and bicarbonate solutions. (orig.)

Facile synthesis of hierarchical CoMn2O4 microspheres with porous and micro-/nanostructural morphology as anode electrodes for lithium-ion batteries

Science.gov (United States)

Li, Yana; Hou, Xianhua; Li, Yajie; Ru, Qiang; Wang, Shaofeng; Hu, Shejun; Lam, Kwok-ho

2017-09-01

Hierarchical CoMn2O4 microspheres assembled by nanoparticles have been successfully synthesized by a facile hydrothermal method and a subsequent annealing treatment. XRD detection indicate the crystal structure. SEM and TEM results reveal the 3-dimensional porous and micro-/nanostructural microsphere assembled by nanoparticles with a size of 20-100 nm. The CoMn2O4 electrode show initial specific discharge capacity of approximately 1546 mAh/g at the current rates 100 mA/g with a coulombic efficiency of 66.7% and remarkable specific capacities (1029-485 mAh/g) at various current rates (100-2800 mA/g). [Figure not available: see fulltext.

First assessment of Li2O-Bi2O3 ceramic oxides for high temperature carbon dioxide capture

Institute of Scientific and Technical Information of China (English)

E.M.Briz-López; M.J.Ramírez-Moreno; I.C.Romero-Ibarra; C.Gómez-Yá(n)ez; H.Pfeiffer; J.Ortiz-Landeros

2016-01-01

The capacity to capture CO2 was determined in several stoichiometric compositions in the Li2O-Bi2O3 system.The compounds (Li7BiO6,Li5BiOs,Li3BiO4 and LiBiO2 phases) were synthesized via solid-state reaction and characterized by X-ray diffraction,scanning electron microscopy and N2 adsorption techniques.The samples were heat-treated at temperatures from 40 to 750 ℃ under the CO2 atmosphere to evaluate the carbonate formation,which is indicative of the capacity of CO2 capture.Moreover,Li7BiO6 shows an excellent CO2 capture capacity of 7.1 mmol/g,which is considerably higher than those of other previously reported ceramics.Li7BiO6 is able to react with CO2 from 240 ℃ to approximately 660 ℃ showing a high kinetic reaction even at CO2 partial pressure values as low as 0.05.

Electrical conductivity in Fe_2O_3 and CoFe_2O_4 nanoparticle arrays and their application in gas sensing

International Nuclear Information System (INIS)

Luby, S.; Benkovicova, M.; Jergel, M.; Siffalovic, P.; Majkova, E.; Rella, R.; Capone, S.; Manera, M. G.

2013-01-01

In this paper we summarize the results obtained as a by product of γ-Fe_2O_3 and CoFe_2O_4 sensors testing. Monodisperse γ-Fe_2O_3 and CoFe_2O_4 NPs with the size of 6.4 ± 0.6 and 7.6 ± 0.6 nm, respectively, were synthesized by high-temperature solution phase reaction from methyl acetylacetonates. The thickness of surfactant is 1 nm and 0.8 nm for two types of NPs, respectively. Surfactant stops the growth of NPs at a certain size. The self-assembled NP monolayers were prepared by Langmuir-Blodgett technique from the colloid solutions spread on the water sub-phase in a standard LB trough. M = 1, 2, 4 or 10 NP monolayers (L) were deposited onto auxiliary oxidized Si substrates or onto 2 mm x 2 mm Al_2O_3 sensor substrates equipped with 20 nm Ti/500 nm Pt comb electrodes to read the measuring current and with 20 nm Ti/500 nm Pt meander on the back side for the heating of the structure to a working temperature. Material properties of NPs and arrays were studied by SEM/EDS, GI XRD, GISAXS, XANES and ellipsometry. (authors)

Emulsifier-free emulsion polymerization produces highly charged, monodisperse particles for near infrared photonic crystals.

Science.gov (United States)

Reese, Chad E; Asher, Sanford A

2002-04-01

We have developed emulsifier-free, emulsion polymerization recipes for the synthesis of highly charged, monodisperse latex particles of diameters between 500 and 1100 nm. These latexes consist of poly[styrene-(co-2-hydroxyethyl methacrylate)] spherical particles whose surfaces are functionalized with sulfate and carboxylic acid groups. These highly charged, monodisperse particles readily self-assemble into robust, three-dimensionally ordered crystalline colloidal array photonic crystals that Bragg diffract light in the near infrared spectral region. By altering the particle number density, the diffraction wavelength can be tuned from approximately 1000 to approximately 4000 nm.

Giant reversible magnetocaloric effect in flower-like β-Co(OH){sub 2} hierarchical superstructures self-assembled by nanosheets

Energy Technology Data Exchange (ETDEWEB)

Liu, Xianguo; Feng, Chao; Xiao, Feng; Jin, Chuangui; Xia, Ailin, E-mail: liuxianguohugh@gmail.com, E-mail: eeswor@polyu.edu.hk [Anhui Key Laboratory of Metal Materials and Processing, School of Materials Science and Engineering, Anhui University of Technology, Ma' anshan, PR (China); Or, Siu Wing [Department of Electrical Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Sun, Yuping [Center for Engineering Practice and Innovation Education, Anhui University of Technology, Ma' anshan, PR (China)

2014-01-15

A facile hydrothermal strategy is proposed to synthesize flower-like β- Co(OH){sub 2} hierarchical microspherical superstructures with a diameter of 0.5-1.5 µm, which are self-assembled by β - Co(OH){sub 2} nano sheets with the average thickness ranging between 20 and 40 nm. The magnetocaloric effect associated with magnetic phase transitions in Co(OH){sub 2} superstructures has been investigated. A sign change in the magnetocaloric effect is induced by a magnetic field, which is related to a filed-induced transition from the antiferromagnetic to the ferromagnetic state below the Néel temperature. The large reversible magnetic-entropy change –ΔS{sub m} (13.4 J/kg K at 15 K for a field change of 5 T) indicates that flower-like Co(OH){sub 2} superstructures is a potential candidate for application in magnetic refrigeration in the low-temperature range. (author)

Facile construction of dual bandgap optical encoding materials with PS@P(HEMA-co-AA)/SiO2-TMPTA colloidal photonic crystals

Science.gov (United States)

Tian, Yu; Zhang, Jing; Liu, Si-Si; Yang, Shengyang; Yin, Su-Na; Wang, Cai-Feng; Chen, Li; Chen, Su

2016-07-01

An operable strategy for the construction of dual-reflex optical code materials from bilayer or Janus-structure colloidal photonic crystals (CPCs) has been established in this work. In this process, monodispersed submicrometer polystryene@poly(2-hydroxyethyl methacrylate-co-acrylic acid) hydrogel microspheres with soft-shell/hard-core structure and monodispersed colloidal silica spheres were fabricated. These two kinds of colloidal units can be facilely integrated into a single material without optical signal interference because they are well isolated for the immiscibility between water and ethoxylated trimethylolpropane triacrylate (TMPTA) and the upper layer of SiO2-TMPTA is a kind of transparent. Moreover, diverse optical code series with different dual photonic bandgaps can be obtained via tuning the colloid sizes. Compared to the conventional single-reflex CPCs, the as-prepared dual-reflex optical code materials represented high information capacity in encoding process. More interesting, delicate code pattern has been also achieved on the optical film via the silk-screen printing technique, which will greatly extend the dual-reflex optical code materials to practical uses in areas containing bio-encoding, anti-counterfeiting, and flexible displays.

Toxicity of inhaled 239PuO2 in Beagle dogs. A. Monodisperse 0.75 μm AMAD particles. B. Monodisperse 1.5 μm AMAD particles. C. Monodisperse 3.0 μm AMAD particles. V

International Nuclear Information System (INIS)

Muggenburg, B.A.; Guilmette, R.A.; Hahn, F.F.; Boecker, B.B.; McClellan, R.O.; Mauderly, J.L.; Pickrell, J.A.

1982-01-01

Studies on the metabolism, dosimetry and biological effects of inhaled particles of 239 PuO 2 in Beagle dogs are in progress. To obtain information on the relative importance of homogeneity versus nonhomogeneity of radiation doses to the lung, dogs have been exposed to monodisperse aerosols of 239 PuO 2 of 0.75, 1.5 or 3.0 μm activity median aerodynamic diameter (AMAD). The exposures have resulted in graded initial lung burdens ranging from 0.0002 to 2.6 μCi 239 Pu per kilogram body weight. Other dogs were exposed to the aerosol diluent to serve as controls. Ten dogs have died in the study with 0.75 μm AMAD particles, 40 dogs have died in the study with 1.5 μm AMAD particles and 35 dogs have died in the study with 3.0 μm AMAD particles of 239 PuO 2 . Dogs have died with radiation pneumonitis and pulmonary fibrosis and carcinomas of the lung. The remaining dogs have survived up to 2100 days after inhalation exposure and are being observed for the remainder of their life span

Hierarchical (Ni,Co)Se 2 /Carbon Hollow Rhombic Dodecahedra Derived from Metal-Organic Frameworks for Efficient Water-Splitting Electrocatalysis

KAUST Repository

Ming, Fangwang

2017-08-12

In this work, we demonstrate that the electrocatalytic activity of transition metal chalcogenides can be greatly enhanced by simultaneously engineering the active sites, surface area, and conductivity. Using metal-organic frameworks-derived (Ni,Co)Se2/C hollow rhombic dodecahedra (HRD) as a demonstration, we show that the incorporation of Ni into CoSe2 could generates additional active sites, the hierarchical hollow structure promotes the electrolyte diffusion, the in-situ hybridization with C improves the conductivity. As a result, the (Ni,Co)Se2/C HRD exhibit superior performance toward the overall water-splitting electrocatalysis in 1M KOH with a cell voltage as low as 1.58V at the current density of 10mAcm−2, making the (Ni,Co)Se2/C HRD as a promising alternative to noble metal catalysts for water splitting.

Hierarchical (Ni,Co)Se 2 /Carbon Hollow Rhombic Dodecahedra Derived from Metal-Organic Frameworks for Efficient Water-Splitting Electrocatalysis

KAUST Repository

Ming, Fangwang; Liang, Hanfeng; Shi, Huanhuan; Mei, Gui; Xu, Xun; Wang, Zhoucheng

2017-01-01

In this work, we demonstrate that the electrocatalytic activity of transition metal chalcogenides can be greatly enhanced by simultaneously engineering the active sites, surface area, and conductivity. Using metal-organic frameworks-derived (Ni,Co)Se2/C hollow rhombic dodecahedra (HRD) as a demonstration, we show that the incorporation of Ni into CoSe2 could generates additional active sites, the hierarchical hollow structure promotes the electrolyte diffusion, the in-situ hybridization with C improves the conductivity. As a result, the (Ni,Co)Se2/C HRD exhibit superior performance toward the overall water-splitting electrocatalysis in 1M KOH with a cell voltage as low as 1.58V at the current density of 10mAcm−2, making the (Ni,Co)Se2/C HRD as a promising alternative to noble metal catalysts for water splitting.

Utilization of CO2 fixating bacterium Actinobacillus succinogenes 130Z for simultaneous biogas upgrading and bio-succinic acid production

DEFF Research Database (Denmark)

Gunnarsson, Ingólfur Bragi; Alvarado-Morales, Merlin; Angelidaki, Irini

2014-01-01

Biogas is an attractive renewable energy carrier. However, it contains CO2 which limits certain applications of biogas. Here we report a novel approach for removing CO2 from biogas and capturing it as a biochemical through a biological process. This approach entails converting CO2 into bio...... and titre, CO2 consumption rate and CH4 purity. When using biogas as the only CO2 source at 140 kPa, the CO2 consumption rate corresponded to 2.59 L CO2 L-1 d-1 with a final succinic acid titre of 14.4 g L-1. Under this pressure condition the highest succinic acid yield and biogas quality reached......-succinic acid using the bacterial strain Actinobacillus succinogenes 130Z, and simultaneously producing high purity CH4 (>95%). Results showed that when pressure during fermentation was increased from 101.325 to 140 kPa, higher CO2 solubility was achieved, thereby positively affecting final succinic acid yield...

Leaf-architectured 3D Hierarchical Artificial Photosynthetic System of Perovskite Titanates Towards CO2 Photoreduction Into Hydrocarbon Fuels

Science.gov (United States)

Zhou, Han; Guo, Jianjun; Li, Peng; Fan, Tongxiang; Zhang, Di; Ye, Jinhua

2013-01-01

The development of an “artificial photosynthetic system” (APS) having both the analogous important structural elements and reaction features of photosynthesis to achieve solar-driven water splitting and CO2 reduction is highly challenging. Here, we demonstrate a design strategy for a promising 3D APS architecture as an efficient mass flow/light harvesting network relying on the morphological replacement of a concept prototype-leaf's 3D architecture into perovskite titanates for CO2 photoreduction into hydrocarbon fuels (CO and CH4). The process uses artificial sunlight as the energy source, water as an electron donor and CO2 as the carbon source, mimicking what real leaves do. To our knowledge this is the first example utilizing biological systems as “architecture-directing agents” for APS towards CO2 photoreduction, which hints at a more general principle for APS architectures with a great variety of optimized biological geometries. This research would have great significance for the potential realization of global carbon neutral cycle. PMID:23588925

Bio-derived three-dimensional hierarchical carbon-graphene-TiO2 as electrode for supercapacitors.

Science.gov (United States)

Jiang, Lili; Ren, Zhifeng; Chen, Shuo; Zhang, Qinyong; Lu, Xiong; Zhang, Hongping; Wan, Guojiang

2018-03-13

This paper reports a novel loofah-derived hierarchical scaffold to obtain three-dimensional biocarbon-graphene-TiO 2 (BC-G-TiO 2 ) composite materials as electrodes for supercapacitors. The loofah scaffold was first loaded with G and TiO 2 by immersing, squeezing, and loosening into the mixed solution of graphene oxide and titania, and then carbonized at 900 °C to form the BC-G-TiO 2 composite. The synergistic effects of the naturally hierarchical biocarbon structure, graphene, and TiO 2 nanoparticles on the electrochemical properties are analyzed. The biocarbon provides a high interconnection and an easy accessibility surface for the electrolyte. Graphene bridged the BC and TiO 2 nanoparticles, improved the conductivity of the BC-G-TiO 2 composite, and increased the electron transfer efficiency. TiO 2 nanoparticles also contributed to the pesudocapacitance and electrochemical stability.

Removal of SO42− from Li2CO3 by Recrystallization in Na2CO3 Solution

Directory of Open Access Journals (Sweden)

Wei Cai

2018-01-01

Full Text Available Li2CO3 with high purity is an important raw material for the fabrication of lithium rechargeable batteries. This paper reports a facile recrystallization way to produce Li2CO3 with high purity from commercial Li2CO3 containing 0.8 wt % of SO42− by the treatment of the commercial Li2CO3 in Na2CO3 solution. The increase of temperature from 30 °C to 90 °C favored the recrystallization of Li2CO3 in Na2CO3 solution and promoted the removal of SO42− adsorbed or doped on/in the commercial Li2CO3. The content of SO42− in Li2CO3 decreased to 0.08 wt % after the treatment of the commercial Li2CO3 in 1.0 mol·L−1 Na2CO3 solution at 90 °C for 10.0 h.

Formation of ternary CaUO2(CO3)3(2-) and Ca2UO2(CO3)3(aq) complexes under neutral to weakly alkaline conditions.

Science.gov (United States)

Lee, Jun-Yeop; Yun, Jong-Il

2013-07-21

The chemical behavior of ternary Ca-UO2-CO3 complexes was investigated by using time-resolved laser fluorescence spectroscopy (TRLFS) in combination with EDTA complexation at pH 7-9. A novel TRLFS revealed two distinct fluorescence lifetimes of 12.7 ± 0.2 ns and 29.2 ± 0.4 ns for uranyl complexes which were formed increasingly dependent upon the calcium ion concentration, even though nearly indistinguishable fluorescence peak shapes and positions were measured for both Ca-UO2-CO3 complexes. For identifying the stoichiometric number of complexed calcium ions, slope analysis in terms of relative fluorescence intensity versus calcium concentration was employed in a combination with the complexation reaction of CaEDTA(2-) by adding EDTA. The formation of CaUO2(CO3)3(2-) and Ca2UO2(CO3)3(aq) was identified under given conditions and their formation constants were determined at I = 0.1 M Na/HClO4 medium, and extrapolated to infinitely dilute solution using specific ion interaction theory (SIT). As a result, the formation constants for CaUO2(CO3)3(2-) and Ca2UO2(CO3)3(aq) were found to be log β113(0) = 27.27 ± 0.14 and log β213(0) = 29.81 ± 0.19, respectively, providing that the ternary Ca-UO2-CO3 complexes were predominant uranium(vi) species at neutral to weakly alkaline pH in the presence of Ca(2+) and CO3(2-) ions.

Toxicity of inhaled 239PuO2 in Beagle dogs. A. Monodisperse 0.75 μm AD particles. B. Monodisperse 1.5 μm AD particles. C. Monodisperse 3.0 μm AD particles. II

International Nuclear Information System (INIS)

Muggenburg, B.A.; Guilmette, R.A.; Hahn, F.F.; McClellan, R.O.; Mauderly, J.L.; Mewhinney, J.A.; Pickrell, J.A.; Boecker, B.B.

1978-01-01

Studies on the metabolism, dosimetry and biological effects of inhaled particles of 239 PuO 2 have been initiated in Beagle dogs. To obtain information on the relative importance of homogeneity of radiation doses to the lung, dogs have been exposed to particles of monodisperse aerosols (sigma/sub g/ 239 PuO 2 ; 40 dogs to the 0.75 μm AD particles, 72 dogs to the 1.5 μm AD particles and 60 dogs to the 3.0 μm AD particles. The exposures have resulted in graded ILB's, which range from 0.0002 to 2.6 μCi/kg body weight. Twenty-nine dogs were exposed to the aerosol diluent and serve as controls. Five dogs have died 336 to 561 days after exposure in the 1.5 μm AD study. Four dogs have died 116 to 589 days after exposure in the 3.0 μm AD study. These dogs had radiation pneumonitis and pulmonary fibrosis at death. The remaining dogs have survived up to 634 days after exposure. It is anticipated that the other dogs planned for these studies will be exposed over the next 12 months

NMR Spectroscopic Characterization of Methylcobalt(III) Compounds with Classical Ligands. Crystal Structures of [Co(NH(3))(5)(CH(3))]S(2)O(6), trans-[Co(en)(2)(NH(3))(CH(3))]S(2)O(6) (en = 1,2-Ethanediamine), and [Co(NH(3))(6)]-mer,trans-[Co(NO(2))(3)(NH(

DEFF Research Database (Denmark)

Kofod, Pauli; Harris, Pernille; Larsen, Sine

1997-01-01

magnetic resonance spectroscopy and by absorption spectroscopy. Single-crystal X-ray structure determinations at 122.0(5) K were performed on [Co(NH(3))(5)(CH(3))]S(2)O(6) (1), trans-[Co(en)(2)(NH(3))(CH(3))]S(2)O(6) (2), and [Co(NH(3))(6)]-mer,trans-[Co(NO(2))(3)(NH(3))(2)(CH(3))](2)-trans-[Co(NO(2...

Synthesis of Mesoporous Single Crystal Co(OH)2 Nanoplate and Its Topotactic Conversion to Dual-Pore Mesoporous Single Crystal Co3O4.

Science.gov (United States)

Jia, Bao-Rui; Qin, Ming-Li; Li, Shu-Mei; Zhang, Zi-Li; Lu, Hui-Feng; Chen, Peng-Qi; Wu, Hao-Yang; Lu, Xin; Zhang, Lin; Qu, Xuan-Hui

2016-06-22

A new class of mesoporous single crystalline (MSC) material, Co(OH)2 nanoplates, is synthesized by a soft template method, and it is topotactically converted to dual-pore MSC Co3O4. Most mesoporous materials derived from the soft template method are reported to be amorphous or polycrystallined; however, in our synthesis, Co(OH)2 seeds grow to form single crystals, with amphiphilic block copolymer F127 colloids as the pore producer. The single-crystalline nature of material can be kept during the conversion from Co(OH)2 to Co3O4, and special dual-pore MSC Co3O4 nanoplates can be obtained. As the anode of lithium-ion batteries, such dual-pore MSC Co3O4 nanoplates possess exceedingly high capacity as well as long cyclic performance (730 mAh g(-1) at 1 A g(-1) after the 350th cycle). The superior performance is because of the unique hierarchical mesoporous structure, which could significantly improve Li(+) diffusion kinetics, and the exposed highly active (111) crystal planes are in favor of the conversion reaction in the charge/discharge cycles.

Ultrathin mesoporous Co{sub 3}O{sub 4} nanosheets-constructed hierarchical clusters as high rate capability and long life anode materials for lithium-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Wu, Shengming [Key Laboratory of Functional Inorganic Materials Chemistry, Ministry of Education, School of Chemistry, Chemical Engineering and Materials, Heilongjiang University, Heilongjiang, Harbin 150080 (China); Xia, Tian, E-mail: xiatian@hlju.edu.cn [Key Laboratory of Functional Inorganic Materials Chemistry, Ministry of Education, School of Chemistry, Chemical Engineering and Materials, Heilongjiang University, Heilongjiang, Harbin 150080 (China); Wang, Jingping [Key Laboratory of Superlight Material and Surface Technology, Ministry of Education, College of Materials Science and Chemical Engineering, Harbin Engineering University, Heilongjiang, Harbin 150001 (China); Lu, Feifei [Key Laboratory of Functional Inorganic Materials Chemistry, Ministry of Education, School of Chemistry, Chemical Engineering and Materials, Heilongjiang University, Heilongjiang, Harbin 150080 (China); Xu, Chunbo [Key Laboratory of Superlight Material and Surface Technology, Ministry of Education, College of Materials Science and Chemical Engineering, Harbin Engineering University, Heilongjiang, Harbin 150001 (China); Zhang, Xianfa; Huo, Lihua [Key Laboratory of Functional Inorganic Materials Chemistry, Ministry of Education, School of Chemistry, Chemical Engineering and Materials, Heilongjiang University, Heilongjiang, Harbin 150080 (China); Zhao, Hui, E-mail: zhaohui98@yahoo.com [Key Laboratory of Functional Inorganic Materials Chemistry, Ministry of Education, School of Chemistry, Chemical Engineering and Materials, Heilongjiang University, Heilongjiang, Harbin 150080 (China)

2017-06-01

Graphical abstract: Ultrathin mesoporous Co{sub 3}O{sub 4} nanosheets-constructed hierarchical clusters (UMCN-HCs) have been successfully synthesized via a facile hydrothermal method followed by a subsequent thermolysis treatment. When tested as anode materials for LIBs, UMCN-HCs achieve high reversible capacity, good long cycling life, and rate capability. - Highlights: • UMCN-HCs show high capacity, excellent stability, and good rate capability. • UMCN-HCs retain a capacity of 1067 mAh g{sup −1} after 100 cycles at 100 mA g{sup −1}. • UMCN-HCs deliver a capacity of 507 mAh g{sup −1} after 500 cycles at 2 A g{sup −1}. - Abstract: Herein, Ultrathin mesoporous Co{sub 3}O{sub 4} nanosheets-constructed hierarchical clusters (UMCN-HCs) have been successfully synthesized via a facile hydrothermal method followed by a subsequent thermolysis treatment at 600 °C in air. The products consist of cluster-like Co{sub 3}O{sub 4} microarchitectures, which are assembled by numerous ultrathin mesoporous Co{sub 3}O{sub 4} nanosheets. When tested as anode materials for lithium-ion batteries, UMCN-HCs deliver a high reversible capacity of 1067 mAh g{sup −1} at a current density of 100 mA g{sup −1} after 100 cycles. Even at 2 A g{sup −1}, a stable capacity as high as 507 mAh g{sup −1} can be achieved after 500 cycles. The high reversible capacity, excellent cycling stability, and good rate capability of UMCN-HCs may be attributed to their mesoporous sheet-like nanostructure. The sheet-layered structure of UMCN-HCs may buffer the volume change during the lithiation-delithiation process, and the mesoporous characteristic make lithium-ion transfer more easily at the interface between the active electrode and the electrolyte.

In-situ preparation of Fe{sub 2}O{sub 3} hierarchical arrays on stainless steel substrate for high efficient catalysis

Energy Technology Data Exchange (ETDEWEB)

Yang, Zeheng, E-mail: zehengyang@hfut.edu.cn [School of Chemistry and Chemical Engineering, Anhui Key Laboratory of Controllable Chemical Reaction & Material Chemical Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China); Wang, Kun; Shao, Zongming; Tian, Yuan [School of Chemistry and Chemical Engineering, Anhui Key Laboratory of Controllable Chemical Reaction & Material Chemical Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China); Chen, Gongde [Department of Chemical and Environmental Engineering, University of California at Riverside, Riverside, CA 92521 (United States); Wang, Kai; Chen, Zhangxian; Dou, Yan [School of Chemistry and Chemical Engineering, Anhui Key Laboratory of Controllable Chemical Reaction & Material Chemical Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China); Zhang, Weixin, E-mail: wxzhang@hfut.edu.cn [School of Chemistry and Chemical Engineering, Anhui Key Laboratory of Controllable Chemical Reaction & Material Chemical Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China)

2017-02-15

Hierarchical array catalysts with micro/nano structures on substrates not only possess high reactivity from large surface area and suitable interface, but intensify mass transfer through shortening the diffusion paths of both reactants and products for high catalytic efficiency. Herein, we first demonstrate fabrication of Fe{sub 2}O{sub 3} hierarchical arrays grown on stainless-steel substrates via in-situ hydrothermal chemical oxidation followed by heat treatment in N{sub 2} atmosphere. As a Fenton-like catalyst, Fe{sub 2}O{sub 3} hierarchical arrays exhibit excellent catalytic activity and life cycle performance for methylene blue (MB) dye degradation in aqueous solution in the presence of H{sub 2}O{sub 2}. The Fe{sub 2}O{sub 3} catalyst with unique hierarchical structures and efficient transport channels, effectively activates H{sub 2}O{sub 2} to generate large quantity of • OH radicals and highly promotes reaction kinetics between MB and • OH radicals. Immobilization of hierarchical array catalysts on stainless-steel can prevent particles agglomeration, facilitate the recovery and reuse of the catalysts, which is expected promising applications in wastewater remediation. - Graphical abstract: The in-situ synthesis of Fe{sub 2}O{sub 3} hierarchical arrays on stainless-steel substrates was reported for the first time, which exhibit excellent catalytic activity performance for methylene blue (MB) dye degradation in aqueous solution in the presence of H{sub 2}O{sub 2}. - Highlights: • Fe{sub 2}O{sub 3} hierarchical arrays was prepared by in-situ hydrothermal chemical oxidation. • F{sup −} ions play an important role in the formation of the Fe{sub 2}O{sub 3} hierarchical arrays. • Fe{sub 2}O{sub 3} hierarchical arrays show high catalytic activity to methylene blue degradation.

Co-Pyrolysis Behaviors of the Cotton Straw/PP Mixtures and Catalysis Hydrodeoxygenation of Co-Pyrolysis Products over Ni-Mo/Al2O3 Catalyst

Directory of Open Access Journals (Sweden)

Derun Hua

2015-12-01

Full Text Available The doping of PP (polypropylene with cotton straw improved the bio-oil yield, which showed there was a synergy in the co-pyrolysis of the cotton straw and PP at the range of 380–480 °C. In a fixed-bed reactor, model compounds and co-pyrolysis products were used for reactants of hydrodeoxygenation (HDO over Ni-Mo/Al2O3. The deoxygenation rate of model compounds decreased over Ni-Mo/Al2O3 in the following order: alcohol > aldehyde > acetic acid > ethyl acetate. The upgraded oil mainly consisted of C11 alkane.

Crystal structure and magnetic properties of the Ba3TeCo3P2O14, Pb3TeCo3P2O14, and Pb3TeCo3V2O14 langasites

DEFF Research Database (Denmark)

Krizan, J.W.; de la Cruz, C.; Andersen, Niels Hessel

2013-01-01

We report the structural and magnetic characterizations of Ba3TeCo3P2O14, Pb3TeCo3P2O14, and Pb3TeCo3V2O14, compounds that are based on the mineral dugganite, which is isostructural to langasites. The magnetic part of the structure consists of layers of Co2+ triangles. Nuclear and magnetic...... structures were determined through a co-refinement of synchrotron and neutron powder diffraction data. In contrast to the undistorted P321 langasite structure of Ba3TeCo3P2O14, a complex structural distortion yielding a large supercell is found for both Pb3TeCo3P2O14 and Pb3TeCo3V2O14. Comparison...... of the three compounds studied along with the zinc analog Pb3TeZn3P2O14, also characterized here, suggests that the distortion is driven by Pb2+ lone pairs; as such, the Pb compounds crystallize in a pyroelectric space group, P2. Magnetic susceptibility, magnetization, and heat capacity measurements were...

Temperature dependence of exchange anisotropy in monodisperse cobalt nanoparticles with a cobalt oxide shell

International Nuclear Information System (INIS)

Spasova, M.; Wiedwald, U.; Farle, M.; Radetic, T.; Dahmen, U.; Hilgendorff, M.; Giersig, M.

2004-01-01

Exchange anisotropy was studied by SQUID magnetometry on an array of monodisperse colloidal nanoparticles consisting of a 7-8 nm diameter FCC Co core covered with a 2-2.5 nm thick FCC CoO shell. Temperature-dependent measurements of the exchange bias field show that the exchange anisotropy vanishes when a magnetic field was applied during cooling below 150 K. The suppression of exchange anisotropy is due to uncompensated interfacial antiferromagnetic spins

SiO{sub 2}@SnO{sub 2}/graphene composite with a coating and hierarchical structure as high performance anode material for lithium ion battery

Energy Technology Data Exchange (ETDEWEB)

Xu, Xingfa; Zhang, Haiyan, E-mail: hyzhang@gdut.edu.cn; Chen, Yiming; Li, Na; Li, Yunyong; Liu, Liying

2016-08-25

In order to ease the agglomeration and huge volume change of SnO{sub 2} particles, SnO{sub 2} nanoparticles were usually anchored on reduced graphene oxide (rGO) and used as anode materials for lithium ion batteries. Unfortunately, graphene sheets tended to overlap with adjacent ones and SnO{sub 2} nanoparticles still suffered from agglomeration and huge volume changes to some extent. In this paper, a composite SiO{sub 2}@SnO{sub 2}/rGO with coating and hierarchical structure was synthesized by a facile hydrothermal method. SnO{sub 2} nanoparticles mono-dispersed on the surface of rGO sheets and SiO{sub 2} spheres, while the SiO{sub 2}@SnO{sub 2} spheres were imbedded in the layers of rGO, which was in favor of alleviating the overlapping of graphene sheets and could make large spacious room to accommodate the huge volume changes of SnO{sub 2} nanoparticles. SiO{sub 2}@SnO{sub 2}/rGO composite also displayed good electrochemical performance. In the first charge/discharge cycle, the SiO{sub 2}@SnO{sub 2}/rGO electrode exhibited a large discharge capacity of 1548 mA h g{sup −1} at a current density of 100 mA g{sup −1} and it still retained a discharge capacity of about 600 mA h g{sup −1} after 100 cycles. - Highlights: • Anodes fabricated by using activated carbon have the highest fracture strength. • SnO{sub 2} nanoparticles are mono-dispersed on the surface of rGO sheets and SiO{sub 2} spheres. • The hierarchical structure SiO{sub 2}@SnO{sub 2}/rGO shows a good electrochemical performance.

Synthesis and crystal structures of nitratocobaltates Na2[Co(NO3)4], K2[Co(NO3)4], and Ag[Co(NO3)3] and potassium nitratonickelate K2[Ni(NO3)4

International Nuclear Information System (INIS)

Morozov, I. V.; Fedorova, A. A.; Albov, D. V.; Kuznetsova, N. R.; Romanov, I. A.; Rybakov, V. B.; Troyanov, S. I.

2008-01-01

The cobalt(II) and nickel(II) nitrate complexes with an island structure (Na 2 [Co(NO 3 ) 4 ] (I) and K 2 [Co(NO 3 ) 4 ] (II)] and a chain structure [Ag[Co(NO 3 ) 3 ] (III) and K 2 [Ni(NO 3 ) 4 ] (IV)] are synthesized and investigated using X-ray diffraction. In the anionic complex [Co(NO 3 ) 4 ] 2− of the crystal structure of compound I, the Co coordination polyhedron is a twisted tetragonal prism formed by the O atoms of four asymmetric bidentate nitrate groups. In the anion [Co(NO 3 ) 4 ] 2− of the crystal structure of compound II, one of the four NO 3 groups is monodentate and the other NO 3 groups are bidentate (the coordination number of the cobalt atom is equal to seven, and the cobalt coordination polyhedron is a monocapped trigonal prism). The crystal structures of compounds III and IV contain infinite chains of the compositions [Co(NO 3 ) 2 (NO 3 ) 2/2 ] − and [Ni(NO 3 ) 3 (NO 3 ) 2/2 ] 2− , respectively. In the crystal structure of compound III, seven oxygen atoms of one monodentate and three bidentate nitrate groups form a dodecahedron with an unoccupied vertex of the A type around the Co atom. In the crystal structure of compound IV, the octahedral polyhedron of the Ni atom is formed by five nitrate groups, one of which is terminal bidentate. The data on the structure of Co(II) coordination polyhedra in the known nitratocobaltates are generalized.

Synthesis and crystal structures of nitratocobaltates Na2[Co(NO3)4], K2[Co(NO3)4], and Ag[Co(NO3)3] and potassium nitratonickelate K2[Ni(NO3)4

International Nuclear Information System (INIS)

Morozov, I. V.; Fedorova, A. A.; Albov, D. V.; Kuznetsova, N. R.; Romanov, I. A.; Rybakov, V. B.; Troyanov, S. I.

2008-01-01

The cobalt(II) and nickel(II) nitrate complexes with an island structure (Na 2 [Co(NO 3 ) 4 ] (I) and K 2 [Co(NO 3 ) 4 ] (II)] and a chain structure [Ag[Co(NO 3 ) 3 ] (III) and K 2 [Ni(NO 3 ) 4 ] (IV)] are synthesized and investigated using X-ray diffraction. In the anionic complex [Co(NO 3 ) 4 ] 2- of the crystal structure of compound I, the Co coordination polyhedron is a twisted tetragonal prism formed by the O atoms of four asymmetric bidentate nitrate groups. In the anion [Co(NO 3 ) 4 ] 2- of the crystal structure of compound II, one of the four NO 3 groups is monodentate and the other NO 3 groups are bidentate (the coordination number of the cobalt atom is equal to seven, and the cobalt coordination polyhedron is a monocapped trigonal prism). The crystal structures of compounds III and IV contain infinite chains of the compositions [Co(NO 3 ) 2 (NO 3 ) 2/2 ] - and [Ni(NO 3 ) 3 (NO 3 ) 2/2 ] 2- , respectively. In the crystal structure of compound III, seven oxygen atoms of one monodentate and three bidentate nitrate groups form a dodecahedron with an unoccupied vertex of the A type around the Co atom. In the crystal structure of compound IV, the octahedral polyhedron of the Ni atom is formed by five nitrate groups, one of which is terminal bidentate. The data on the structure of Co(II) coordination polyhedra in the known nitratocobaltates are generalized

Hydrothermal liquefaction of pinewood (Pinus ponderosa) for H2, biocrude and bio-oil generation

International Nuclear Information System (INIS)

Tungal, Richa; Shende, Rajesh V.

2014-01-01

Highlights: • Ni(NO 3 ) 2 , Ca(NO 3 ) 2 , Co(NO 3 ) 2 and Fe(NO 3 ) 3 were investigated for HTL of pinewood. • Ni(NO 3 ) 2 showed higher selectivity for H 2 and biocrude generation. • O/C ratio of LBO, HBO and residue recovered was lower than O/C of the pinewood. • HHVs of LBO, HBO and residue were found to be higher than HHV of the pinewood. - Abstract: This study reports hydrothermal liquefaction (HTL) of pinewood at 200–275 °C for H 2 , biocrude and bio-oil production in presence of a nitrate salt catalyst: Ni(NO 3 ) 2 , Ca(NO 3 ) 2 , Co(NO 3 ) 2 and Fe(NO 3 ) 3 . Among these catalysts, Ni(NO 3 ) 2 showed higher selectivity towards H 2 and biocrude generation. To generate H 2 and biocrude, a slurry of pinewood was prepared with different biomass to solvent (B:S) ratios of 1:10, 1:30, and 1:75 and loaded in the SS316 PARR reactor and heated to different temperatures. While the reaction was in progress, gas samples were withdrawn and analyzed using GC equipped with Chrompack capillary column and thermal conductivity detector. The analysis of product gas revealed the presence of H 2 , CO 2 , CO and CH 4 . The liquid samples collected during the reaction were centrifuged to separate residue and analyzed using TOC analyzer, HPLC and GC–MS. Among different homogeneous catalysts used, Ni(NO 3 ) 2 yielded 12.26 mol% H 2 at 275 °C and a maximum biocrude of 55 wt% at 250 °C using 200 psi N 2 partial pressure. The biocrude was found to contain sugars, C 1 -C 3 carboxylic acids such as lactic, propionic, acetic and formic, HMF/furfural and other oxygenated compounds, which were thoroughly analyzed by GC–MS. Among different C 1 -C 3 acids, lactic acid was observed in the major amount of 83.92 wt% using B:S of 1:75 at 250 °C. The biocrude obtained was further processed to recover light bio-oil (LBO), heavy bio-oil (HBO) and residue which were found to have higher heating value (HHV) as compared with original pinewood

Panorama 2013 - Air transport and the problem of CO2: ETS mechanisms and bio-jet fuels

International Nuclear Information System (INIS)

Jean-Francois Gruson

2013-01-01

Air transport currently accounts for only 2% (∼600 Mt/year) of global CO 2 emissions from human activity. Despite this 2% level, this industry is targeted by governments - especially European Union - and initiatives targeting zero growth in carbon from 2020 onwards, and a 50% reduction by 2050. Over and above aircraft technical innovations and the way in which air traffic is organised, the introduction of ETS (Emissions Trading System) mechanisms and the development of bio-jet fuels are the options most commonly cited in discussions on how to achieve that target. (author)

Magnetic and Moessbauer studies on GdCo3B2 and DyCo3B2

International Nuclear Information System (INIS)

Malik, S.K.; Umarji, A.M.; Shenoy, G.K.

1984-10-01

Magnetization and Moessbauer studies have been carried out on GdCo 3 B 2 and DyCo 3 B 2 . These compounds are magnetically ordered with Curie temperatures of 56 0 and 21 0 K respectively. The Co atoms are either nonmagnetic or carry a small moment in these compounds. The saturation moment of DyCo 3 B 2 at 5 0 K is smaller than the Dy 3+ free-ion value. From 161 Dy Moessbauer studies, the measured hyperfine magnetic field at the Dy site is also observed to be smaller than the free-ion value. 155 Gd Moessbauer measurements in GdCo 3 B 2 reveal the presence of large crystalline electric fields at the rare earth site. This causes the moment and the hyperfine field at the Dy site in DyCo 3 B 2 to be reduced from its free-ion value

Facile Synthesis of Monodispersed Polysulfide Spheres for Building Structural Colors with High Color Visibility and Broad Viewing Angle.

Science.gov (United States)

Li, Feihu; Tang, Bingtao; Wu, Suli; Zhang, Shufen

2017-01-01

The synthesis and assembly of monodispersed colloidal spheres are currently the subject of extensive investigation to fabricate artificial structural color materials. However, artificial structural colors from general colloidal crystals still suffer from the low color visibility and strong viewing angle dependence which seriously hinder their practical application in paints, colorimetric sensors, and color displays. Herein, monodispersed polysulfide (PSF) spheres with intrinsic high refractive index (as high as 1.858) and light-absorbing characteristics are designed, synthesized through a facile polycondensation and crosslinking process between sodium disulfide and 1,2,3-trichloropropane. Owing to their high monodispersity, sufficient surface charge, and good dispersion stability, the PSF spheres can be assembled into large-scale and high-quality 3D photonic crystals. More importantly, high structural color visibility and broad viewing angle are easily achieved because the unique features of PSF can remarkably enhance the relative reflectivity and eliminate the disturbance of scattering and background light. The results of this study provide a simple and efficient strategy to create structural colors with high color visibility, which is very important for their practical application. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fabrication of hierarchical porous ZnO-Al2O3 microspheres with enhanced adsorption performance

Science.gov (United States)

Lei, Chunsheng; Pi, Meng; Xu, Difa; Jiang, Chuanjia; Cheng, Bei

2017-12-01

Hierarchical porous ZnO-Al2O3 microspheres were fabricated through a simple hydrothermal route. The as-prepared hierarchical porous ZnO-Al2O3 composites were utilized as adsorbents to remove organic dye Congo red (CR) from water. The ZnO-Al2O3 composites had morphology of microspheres with diameters in the range of 12-16 μm, which were assembled by nanosheets with thicknesses of approximately 60 nm. The adsorption kinetics of CR onto the ZnO-Al2O3 composites was properly fitted by the pseudo-second-order kinetic model. The equilibrium adsorption data were perfectly described by the Langmuir isotherm and had a maximum adsorption capacity that reached 397 mg/g, which was significantly higher than the value of the pure alumina (Al2O3) and zinc oxide (ZnO) samples. The superior CR removal efficiency of the ZnO-Al2O3 composites was attributed to its well-developed hierarchical porous structures and larger specific surface area (201 m2/g), which were conducive to the diffusion and adsorption of CR molecules. Moreover, the regeneration study reveals that the ZnO-Al2O3 composites have suitable stability and reusability. The results also indicate that the as-prepared sample can act as a highly effective adsorbent in anionic dye removal from wastewater.

A common behaviour of thermoelectric layered cobaltites: incommensurate spin density wave states in [Ca2Co4/3Cu2/3O4]0.62[CoO2] and [Ca2CoO3]0.62[CoO2

International Nuclear Information System (INIS)

Sugiyama, J; Brewer, J H; Ansaldo, E J; Itahara, H; Dohmae, K; Xia, C; Seno, Y; Hitti, B; Tani, T

2003-01-01

Magnetism of a misfit layered cobaltite [Ca 2 Co 4/3 Cu 2/3 O 4 ] x RS [CoO 2 ] (x ∼ 0.62, RS denotes a rocksalt-type block) was investigated by a positive muon spin rotation and relaxation (μ + SR) experiment. A transition to an incommensurate (IC) spin density wave (SDW) state was found below 180 K (= T C on ); and a clear oscillation due to a static internal magnetic field was observed below 140 K(= T C ). Furthermore, an anisotropic behaviour of the zero-field μ + SR experiment indicated that the IC-SDW lies in the a-b plane, with oscillating moments directed along the c axis. These results were quite similar to those for the related compound [Ca 2 CoO 3 ] 0.62 RS [CoO 2 ], i.e., Ca 3 Co 4 O 9 . Since the IC-SDW field in [Ca 2 Co 4/3 Cu 2/3 O 4 ] 0.62 RS [CoO 2 ] was approximately the same as those in pure and doped [Ca 2 CoO 3 ] 0.62 RS [CoO 2 ], it was concluded that the IC-SDW exists in the [CoO 2 ] planes

Application of monodisperse fibers and discs to evaluation of the aerodynamic particle sizer

International Nuclear Information System (INIS)

Hoover, M.D.; Lipowicz, P.J.; Hanson, R.W.; Yeh, H.C.; Casalnuovo, S.A.

1988-01-01

Monodisperse fibers, μm in width and lengths of 5, 10, 20, and 40 μm, as well as monodisperse discs, 2 4 8, or 12 μm in diameter, were prepared using an integrated circuit microchip fabrication technique. Particles were silicon dioxide with thickness of 1 μm. Examination of the particles using a scanning electron microscope showed that they were uniform in shape, with well-defined edges. The particles were suspended in distilled water and aerosolized with a Lovelace nebullizer. The monodisperse particles were used to evaluate the TSI Aerodynamic Particle Sizer (APS). Carbon fibers that were monodisperse in diameter (count median diameter 3.42 μm, geometric standard deviation 1.06) and polydisperse in length (count median length = 28 μm, geometric standard deviation 2.2) were also used. The APS was found to be insensitive to fiber length and only weakly sensitive to disc diameter. (author)

Effects of freshwater Synechococcus sp. cyanobacteria pH buffering on CaCO3 precipitation: Implications for CO2 sequestration

International Nuclear Information System (INIS)

Martinez, Raul E.; Weber, Sebastian; Grimm, Christian

2016-01-01

In the present study, a mixed-flow steady-state bio-reactor was designed to biomineralize CO 2 as a consequence of photosynthesis from active Synechococcus sp. Dissolved CO 2 , generated by constant air bubbling of inorganic and cyanobacteria stock solutions, was the only source of inorganic carbon. The release of hydroxide ion by cyanobacteria from photosynthesis maintained highly alkaline pH conditions. In the presence of Ca 2+ and carbonate species, this led to calcite supersaturation under steady state conditions. Ca 2+ remained constant throughout the experiments showing the presence of steady state conditions. Similarly, the Synechococcus sp. biomass concentration remained stable within uncertainty. A gradual pH decrease was observed for the highest Ca 2+ condition coinciding with the formation of CaCO 3 . The high degree of supersaturation, under steady-state conditions, contributed to the stabilization of calcite and maintained a constant driving force for the mineral nucleation and growth. For the highest Ca 2+ condition a fast crystal growth rate was consistent with rapid calcite precipitation as suggested further by affinity calculations. Although saturation state based kinetic precipitation models cannot accurately reflect the controls on crystal growth kinetics or reliably predict growth mechanisms, the relatively reaction orders obtained from modeling of calcite precipitation rates as function of decreasing carbonate concentration suggest that the precipitation occurred via surface-controlled rate determining reactions. These high reaction orders support in addition the hypothesis that crystal growth proceeded through complex surface controlled mechanisms. In conclusion, the steady state supersaturated conditions generated by a constant cyanobacteria biomass and metabolic activity strongly suggest that these microorganisms could be used for the development of efficient CO 2 sequestration methods in a controlled large-scale environment. - Highlights: �

Formation of 1D hierarchical structures composed of Ni{sub 3}S{sub 2} nanosheets on CNTs backbone for supercapacitors and photocatalytic H{sub 2} production

Energy Technology Data Exchange (ETDEWEB)

Zhu, Ting; Wu, Hao Bin; Wang, Yabo; Xu, Rong; Lou, Xiong Wen [David] [School of Chemical and Biomedical Engineering, Nanyang Technological University, 70 Nanyang Drive, Singapore 637457 (Singapore)

2012-12-15

One-dimensional (1D) hierarchical structures composed of Ni{sub 3}S{sub 2} nanosheets grown on carbon nanotube (CNT) backbone (denoted as CNT rate at Ni{sub 3}S{sub 2}) are fabricated by a rational multi-step transformation route. The first step involves coating the CNT backbone with a layer of silica to form CNT rate at SiO{sub 2}, which serves as the substrate for the growth of nickel silicate (NiSilicate) nanosheets in the second step to form CNT rate at SiO{sub 2} rate at NiSilicate core-double shell 1D structures. Finally the as-formed CNT rate at SiO{sub 2} rate at NiSilicate 1D structures are converted into CNT-supported Ni{sub 3}S{sub 2} nanosheets via hydrothermal treatment in the presence of Na{sub 2}S. Simultaneously the intermediate silica layer is eliminated during the hydrothermal treatment, leading to the formation of CNT rate at Ni{sub 3}S{sub 2} nanostructures. Because of the unique hybrid nano-architecture, the as-prepared 1D hierarchical structure is shown to exhibit excellent performance in both supercapacitors and photocatalytic H{sub 2} production. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Hierarchical La0.7Ce0.3FeO3/halloysite nanocomposite for photocatalytic degradation of antibiotics

Science.gov (United States)

Li, Xiazhang; Zhu, Wei; Yan, Xiangyu; Lu, Xiaowang; Yao, Chao; Ni, Chaoying

2016-08-01

The hierarchical La0.7Ce0.3FeO3/halloysite nanotubes (HNTs) composites have been successfully prepared via sol-gel method. XRD and TEM characterizations indicated that the sheet-like La0.7Ce0.3FeO3 coupled with the co-precipitated CeO2 were evenly deposited onto the surface of halloysite. The photocatalytic degradation of chlortetracycline under visible light irradiation using La0.7Ce0.3FeO3/HNTs as catalyst was evaluated by high-performance liquid chromatography, which exhibited remarkable photocatalytic activity with the removal rate up to 99 % in 90 min, due to the formation of "solid solution/co-precipitation" heterostructure as well as the excellent adsorptive capability of halloysite for antibiotics.

Hierarchical La0.7Ce0.3FeO3/halloysite nanocomposite for photocatalytic degradation of antibiotics

International Nuclear Information System (INIS)

Li, Xiazhang; Yao, Chao; Zhu, Wei; Yan, Xiangyu; Lu, Xiaowang; Ni, Chaoying

2016-01-01

The hierarchical La 0.7 Ce 0.3 FeO 3 /halloysite nanotubes (HNTs) composites have been successfully prepared via sol-gel method. XRD and TEM characterizations indicated that the sheet-like La 0.7 Ce 0.3 FeO 3 coupled with the co-precipitated CeO 2 were evenly deposited onto the surface of halloysite. The photocatalytic degradation of chlortetracycline under visible light irradiation using La 0.7 Ce 0.3 FeO 3 /HNTs as catalyst was evaluated by high-performance liquid chromatography, which exhibited remarkable photocatalytic activity with the removal rate up to 99 % in 90 min, due to the formation of ''solid solution/co-precipitation'' heterostructure as well as the excellent adsorptive capability of halloysite for antibiotics. (orig.)

Host Plant Physiology and Mycorrhizal Functioning Shift across a Glacial through Future [CO2] Gradient.

Science.gov (United States)

Becklin, Katie M; Mullinix, George W R; Ward, Joy K

2016-10-01

Rising atmospheric carbon dioxide concentration ([CO 2 ]) may modulate the functioning of mycorrhizal associations by altering the relative degree of nutrient and carbohydrate limitations in plants. To test this, we grew Taraxacum ceratophorum and Taraxacum officinale (native and exotic dandelions) with and without mycorrhizal fungi across a broad [CO 2 ] gradient (180-1,000 µL L -1 ). Differential plant growth rates and vegetative plasticity were hypothesized to drive species-specific responses to [CO 2 ] and arbuscular mycorrhizal fungi. To evaluate [CO 2 ] effects on mycorrhizal functioning, we calculated response ratios based on the relative biomass of mycorrhizal (M Bio ) and nonmycorrhizal (NM Bio ) plants (R Bio = [M Bio - NM Bio ]/NM Bio ). We then assessed linkages between R Bio and host physiology, fungal growth, and biomass allocation using structural equation modeling. For T. officinale, R Bio increased with rising [CO 2 ], shifting from negative to positive values at 700 µL L -1 [CO 2 ] and mycorrhizal effects on photosynthesis and leaf growth rates drove shifts in R Bio in this species. For T. ceratophorum, R Bio increased from 180 to 390 µL L -1 and further increases in [CO 2 ] caused R Bio to shift from positive to negative values. [CO 2 ] and fungal effects on plant growth and carbon sink strength were correlated with shifts in R Bio in this species. Overall, we show that rising [CO 2 ] significantly altered the functioning of mycorrhizal associations. These symbioses became more beneficial with rising [CO 2 ], but nonlinear effects may limit plant responses to mycorrhizal fungi under future [CO 2 ]. The magnitude and mechanisms driving mycorrhizal-CO 2 responses reflected species-specific differences in growth rate and vegetative plasticity, indicating that these traits may provide a framework for predicting mycorrhizal responses to global change. © 2016 American Society of Plant Biologists. All Rights Reserved.

The bio-energies development: the role of biofuels and the CO{sub 2} price

Energy Technology Data Exchange (ETDEWEB)

Jouvet, Pierre-Andre [Universite Paris Ouest Nanterre La Defense, Climate Economics Chair (France); Lantz, Frederic [IFP Energies nouvelles, 1-4, avenue de Bois-Preau, 92852 Rueil-Malmaison Cedex (France); Le Cadre, Elodie [IFPEN, INRA, Universite Paris Ouest Nanterre La Defense (France)

2012-07-01

Reduction in energy dependency and emissions of CO{sub 2} via renewable energies targeted in the European Union energy mix and taxation system, might trigger the production of bio-energy production and competition for biomass utilization. Torrefied biomass could be used to produce second generation biofuels to replace some of the fuels used in transportation and is also suitable as feedstock to produce electricity in large quantities. This paper examines how the CO{sub 2} price affects demand of torrefied biomass in the power sector and its consequences on the profitability of second generation biofuel units (Biomass to Liquid units). Indeed, the profitability of the BtL units which are supplied only by torrefied biomass is related to the competitive demand of the power sector driven by the CO{sub 2} price and feed-in tariffs. We propose a linear dynamic model of supply and demand. On the supply side, a profit-maximizing torrefied biomass sector is modelled. The model aims to represent the transformation of biomass into torrefied biomass which could be sold to the refinery sector and the power sector. A two-sided (demanders and supplier) bidding process led us to arrive at the equilibrium price for torrefied biomass. The French case is used as an example. Our results suggest that the higher the CO{sub 2} price, the more stable and important the power sector demand. It also makes the torrefied biomass production less vulnerable to uncertainty on demand coming from the refining sector. The torrefied biomass co-firing with coal can offer a near-term market for the torrefied biomass for a CO{sub 2} emission price lower than 20 euros/tCO{sub 2}, which can stimulate development of biomass supply systems. Beyond 2020, the demand for torrefied biomass from the power sector could be substituted by the refining sector if the oil price goes up whatever the CO{sub 2} price. (authors)

Hollow carbon spheres with encapsulation of Co3O4 nanoparticles as anode material for lithium ion batteries

International Nuclear Information System (INIS)

Zhan Liang; Wang Yanli; Qiao Wenming; Ling, Licheng; Yang Shubin

2012-01-01

Graphical abstract: Hollow carbon spheres with encapsulation of Co 3 O 4 nanoparticles were synthesized. As anode materials for lithium ion battery, the reversible capacity of obtained electrode is as high as 732 mAh g −1 at 74 mA g −1 and 500 mAh g −1 at 744 mA g −1 . - Abstract: Based on the high theoretical capacity of Co 3 O 4 for lithium storage, a noval type of monodisperse hollow carbon spheres with encapsulation of Co 3 O 4 nanoparticles (HCSE-Co 3 O 4 ) were designed and synthesized. The monodisperse hollow carbon spheres not only can provide enough void volume to accommodate the volume change of encapsulated Co 3 O 4 nanoparicles, but also can prevent the formation of solid electrolyte interface (SEI) films on the surface of Co 3 O 4 nanoparticles and following direct contact of Co and SEI films upon lithium extraction. The HCSE-Co 3 O 4 electrode exhibit highly reversible capacity, excellent cycle performance and rate capability attributed to the unique structure. The reversible capacity of HCSE-Co 3 O 4 electrode is as high as 500 mAh g −1 at a current density of 744 mA g −1 , while that of bare Co 3 O 4 electrode is only around 80 mAh g −1 .

Hierarchical mesoporous graphene@Ni-Co-S arrays on nickel foam for high-performance supercapacitors

International Nuclear Information System (INIS)

Nguyen, Van Hoa; Lamiel, Charmaine; Shim, Jae-Jin

2015-01-01

Highlights: • Hierarchical mesoporous graphene@Ni-Co-S arays have been decorated on Ni foam. • The electrode exhibits a high specific capacitance of 9.2 F cm −1 at 100 mA cm −1 . • The electrode presents large electroactive surface area and excellent structural stability. - Abstract: Hierarchical mesoporous graphene and ternary nickel cobalt sulfide (Ni-Co-S) arrays on nickel foam were designed and fabricated by chemical vapor deposition and electrodeposition for supercapacitor applications. The electrodes exhibited rapid electron and ion transport, large electroactive surface area, and excellent structural stability owing to the highly conductive, mesoporous nature of graphene and the Ni-Co-S nanosheets, as well as to the open framework of the three-dimensional nanoarchitectures. The specific capacitance of the obtained electrode was as high as 9.2 F cm −1 at a high current density of 100 mA cm −1 , indicating promising applications as an efficient electrode for electrochemical capacitors

Co-crystallization phase transformations in all π-conjugated block copolymers with different main-chain moieties.

Science.gov (United States)

Lee, Yi-Huan; Chen, Wei-Chih; Yang, Yi-Lung; Chiang, Chi-Ju; Yokozawa, Tsutomu; Dai, Chi-An

2014-05-21

Driven by molecular affinity and balance in the crystallization kinetics, the ability to co-crystallize dissimilar yet self-crystallizable blocks of a block copolymer (BCP) into a uniform domain may strongly affect its phase diagram. In this study, we synthesize a new series of crystalline and monodisperse all-π-conjugated poly(2,5-dihexyloxy-p-phenylene)-b-poly(3-(2-ethylhexyl)thiophene) (PPP-P3EHT) BCPs and investigate this multi-crystallization effect. Despite vastly different side-chain and main-chain structures, PPP and P3EHT blocks are able to co-crystallize into a single uniform domain comprising PPP and P3EHT main-chains with mutually interdigitated side-chains spaced in-between. With increasing P3EHT fraction, PPP-P3EHTs undergo sequential phase transitions and form hierarchical superstructures including predominately PPP nanofibrils, co-crystalline nanofibrils, a bilayer co-crystalline/pure P3EHT lamellar structure, a microphase-separated bilayer PPP-P3EHT lamellar structure, and finally P3EHT nanofibrils. In particular, the presence of the new co-crystalline lamellar structure is the manifestation of the interaction balance between self-crystallization and co-crystallization of the dissimilar polymers on the resulting nanostructure of the BCP. The current study demonstrates the co-crystallization nature of all-conjugated BCPs with different main-chain moieties and may provide new guidelines for the organization of π-conjugated BCPs for future optoelectronic applications.

Phase separation of bio-oil produced by co-pyrolysis of corn cobs and polypropylene

Science.gov (United States)

Supramono, D.; Julianto; Haqqyana; Setiadi, H.; Nasikin, M.

2017-11-01

In co-pyrolysis of biomass-plastics, bio-oil produced contains both oxygenated and non-oxygenated compounds. High oxygen composition is responsible for instability and low heating value of bio-oil and high acid content for corrosiveness. Aims of the present work are to evaluate possibilities of achieving phase separation between oxygenated and non-oxygenated compounds in bio-oil using a proposed stirred tank reactor and to achieve synergistic effects on bio-oil yield and non-oxygenated compound layer yield. Separation of bio-oil into two layers, i.e. that containing oxygenated compounds (polar phase) and non-oxygenated compounds (non-polar phase) is important to obtain pure non-polar phase ready for the next processing of hydrogenation and used directly as bio-fuel. There has been no research work on co-pyrolysis of biomass-plastic considering possibility of phase separation of bio-oil. The present work is proposing a stirred tank reactor for co-pyrolysis with nitrogen injection, which is capable of tailoring co-pyrolysis conditions leading to low viscosity and viscosity asymmetry, which induce phase separation between polar phase and non-polar phase. The proposed reactor is capable of generating synergistic effect on bio-oil and non-polar yields as the composition of PP in feed is more than 25% weight in which non-polar layers contain only alkanes, alkenes, cycloalkanes and cycloalkenes.

Biodiesel synthesis using K2CO3/Al–O–Si aerogel catalysts

Directory of Open Access Journals (Sweden)

IVANA LUKIĆ

2010-06-01

Full Text Available In this study, catalysts for fatty acid methyl esters (FAME or bio-diesel synthesis with K2CO3 as the active component on an alumina/silica support were synthesized using the sol–gel method, which was followed by drying the “dense” wet gels with supercritical carbon dioxide to obtain the aerogels. The prepared catalysts were characterized by XRD analysis, FTIR spectroscopy and N2 physisorption at 77 K, and tested in the methanolysis of sunflower oil. The effects of reaction variables, such as reaction time, temperature and methanol to oil molar ratio, on the yield of FAME were investigated. The aerogel catalysts with K2CO3 as the active component on an alumina/silica support exhibited good activity in the methanolysis of sunflower oil. The leaching of potassium when the catalyst was in contact with pure methanol under the working conditions of methanolysis was also tested in this study, indicating that it occurred only at higher temperatures, while at lower ones, it was negligible.

Synthesis, characterization and magnetic property of maghemite (γ-Fe2O3) nanoparticles and their protective coating with pepsin for bio-functionalization

International Nuclear Information System (INIS)

Bandhu, A.; Sutradhar, S.; Mukherjee, S.; Greneche, J.M.; Chakrabarti, P.K.

2015-01-01

Highlights: • Maghemite nanoparticles were prepared by a modified co-precipitation method. • Nanoparticles were then successfully coated with pepsin for bio-functionlization. • XRD and Mössbauer spectra confirmed the maghemite phase of the nanoparticles. • Magnetic data were analysed to evaluate particle size, anisotropy etc. - Abstract: Maghemite nanoparticles (γ-Fe 2 O 3 ) are prepared by co-precipitation method. To obtain bio-functionalized magnetic nanoparticles for magnetically controlled drug delivery, the prepared nanoparticles are successfully coated with pepsin, a bio-compatible polymer and digestive enzyme. Crystallographic phase of the nanoparticles is confirmed by X-ray diffractograms (XRD), high resolution transmission electron microscopy (HRTEM) and 57 Fe Mössbauer spectrometry. The average size of nanoparticles/nanocrystallites is estimated from the (3 1 1) peak of the XRD pattern using Debye–Scherrer formula. Results of HRTEM of coated and bare samples are in good agreement with those extracted from the XRD analysis. The dynamic magnetic properties are observed and different quantities viz., coercive field, magnetization, remanence, hysteresis losses etc., are estimated, which confirmed the presence of superparamagnetic relaxation of nanoparticles. Mössbauer spectra of the samples recorded at both 300 and 77 K, confirmed that the majority of particles are maghemite together with a very small fraction of magnetite nanoparticles

Hierarchical MoS2 nanowires/NiCo2O4 nanosheets supported on Ni foam for high-performance asymmetric supercapacitors

Science.gov (United States)

Wen, Shiyang; Liu, Yu; Zhu, Fangfang; Shao, Rong; Xu, Wei

2018-01-01

The hierarchical MoS2 nanowires/NiCo2O4 nanosheets (MS/NCO) supercapacitor electrode materials supported on Ni foam were synthesized by a two-step hydrothermal method. The capacitance was investigated by using various electrochemical methods including cyclic voltammetry, constant-current galvanostatic charge/discharge curves and electrochemical impedance spectroscopy. The MS/NCO networks show 7 times more capacitance (7.1 F cm-2) than pure NiCo2O4 nanosheets by CV at a scan rate of 2 mV s-1. The specific capacitance of the assembled MS/NCO//active carbon (AC) asymmetric supercapacitor could reach up to 51.7 F g-1 at a current density of 1.5 A g-1. Also, the maximum energy density of 18.4 W h kg-1 at a power density of 1200.2 W kg-1 was achieved, with 98.2% specific capacitance retention after 8000 cycles. These exciting results exhibit potential application in developing energy storage devices with high energy density and high power density.

Hierarchically porous CoFe2O4 nanosheets supported on Ni foam with excellent electrochemical properties for asymmetric supercapacitors

Science.gov (United States)

Gao, Hongyan; Xiang, Junjie; Cao, Yan

2017-08-01

A new type of hierarchically mesoporous cobalt ferrite oxide nanosheets, CoFe2O4 nanosheets, has been successfully fabricated via a simple hydrothermal method on the Ni foam followed by a post-annealing treatment. This CoFe2O4 nanosheets was employed as a supercapacitor electrode and exhibited an excellent capacitance of 503 F g-1 at a current density of 2 A g-1. When the current density increased to 20 A g-1, the capacitance of CoFe2O4 nanosheets can maintain 78.5% (395 F g-1) of the initial value, indicating the remarkable rate capability of the as-prepared CoFe2O4 nanosheets. An aqueous asymmetric supercapacitor (ASC) based on CoFe2O4 nanosheets as a positive electrode and the activated carbon (AC) as a negative electrode was assembled for the first time. The as-fabricated ASC delivered a specific capacitance of 73.12 F g-1 at a current density of 1.2 A g-1 in a voltage window of 1.5 V. The CoFe2O4//AC ASC could achieve a high energy density of 22.85 W h kg-1 and good long-term cycling stability (98% retention after 5000 cycles). These results demonstrated that CoFe2O4 nanosheets could be one of the promising electrode material for supercapacitors applications.

Bio-fuel co-products in France: perspectives and consequences for cattle food

International Nuclear Information System (INIS)

2010-01-01

The development of bio-fuels goes along with that of co-products which can be used to feed animals. After having recalled the political context which promotes the development of renewable energies, this document aims at giving an overview of the impact of bio-fuel co-products on agriculture economy. It discusses the production and price evolution for different crops

Fabrication of Superhydrophobic Surface with Controlled Wetting Property by Hierarchical Particles.

Science.gov (United States)

Xu, Jianxiong; Liu, Weiwei; Du, Jingjing; Tang, Zengmin; Xu, Lijian; Li, Na

2015-04-01

Hierarchical particles were prepared by synthetically joining appropriately functionalized polystyrene spheres of poly[styrene-co-(3-(4-vinylphenyl)pentane-2,4-dione)] (PS-co-PVPD) nanoparticles and poly(styrene-co-chloromethylstyrene) (PS-co-PCMS) microparticles. The coupling reaction of nucleophilic substitution of pendent β-diketone groups with benzyl chloride was used to form the hierarchical particles. Since the polymeric nanoparticles and microparticles were synthesized by dispersion polymerization and emulsion polymerization, respectively, both the core microparticles and the surface nanoparticles can be different size and chemical composition. By means of changing the size of the PS-co-PVPD surface nanoparticles, a series of hierarchical particles with different scale ratio of the micro/nano surface structure were successfully prepared. Moreover, by employing the PS-co-PVPD microparticles and PS-co-PCMS nanoparticles as building blocks, hierarchical particles with surface nanoaprticles of different composition were made. These as-prepared hierarchical particles were subsequently assembled on glass substrates to form particulate films. Contact angle measurement shows that superhydrophobic surfaces can be obtained and the contact angle of water on the hierarchically structured surface can be adjusted by the scale ratio of the micro/nano surface structure and surface chemical component of hierarchical particles.

Synthesis and characterization of lanthanide-based luminescent nanoparticles: toward new bio-labels

International Nuclear Information System (INIS)

Lechevallier, Severine

2010-01-01

This work deals with the development of luminescent nanoparticles (NPs) suitable as bio-labels. Inorganic NPs have been synthesized, in which luminescent ion (Eu 3+ in most of cases) is substituting ions of the oxide host matrix. NPs of Ln(OH)CO 3 :Eu 3+ (Ln = Y or Gd), Ln 2 O 3 :Eu 3+ , Ln 2 O 2 S:Eu 3+ and SiO 2 :Eu 3+ have been characterized by the way of TGA, WAXS-XRD, TEM, IR and photoluminescence (PL) techniques. The controlled precipitation using urea as precipitating agent is the way chosen and optimized to obtain spherical and monodispersed in size (150±15 nm) NPs. These particles of amorphous lanthanide hydroxycarbonate can directly be used as luminescent bio-labels or after their conversion in oxide or oxi-sulfide. For the silica particles, the synthesis by aerosol pyrolysis has been used. The obtained particles are spherical with a main diameter of 350 nm. In a second step, the surface of the inorganic NPs has been modified, in order to graft amino-reactive functions. Several modification ways have been explored: with APTES (aminopropyltriethoxysilane), with TEOS (tetra-ethoxysilane) and then APTES, or with a TEOS/APTES mixture. The same characterizations techniques have been applied to the modified particles, and chemical analysis, solid state NMR and XPS. DLS and ζ-potential of the NPs dispersed in water have also been measured. These analyses have been completed by the evaluation of the number of accessible amine functions by coupling with FITC (fluorescein isothiocyanate). The direct modification of oxides (Y 2 O 3 or Gd 2 O 3 ) with APTES is the best way, and an homogenous layer of 1 nm with a high number of accessible amine can be graft. Finally, to move toward luminescent bio-labelling in biological medium, the luminescence of the NPs has been observed and analyzed using: - A spectro-fluorimeter, after their dispersion in water; - A fluorescence microscope, on glass slides, under broad band excitation; - A confocal microscope, under laser

High photocatalytic activity of hierarchical SiO2@C-doped TiO2 hollow spheres in UV and visible light towards degradation of rhodamine B.

Science.gov (United States)

Zhang, Ying; Chen, Juanrong; Hua, Li; Li, Songjun; Zhang, Xuanxuan; Sheng, Weichen; Cao, Shunsheng

2017-10-15

Ongoing research activities are targeted to explore high photocatalytic activity of TiO 2 -based photocatalysts for the degradation of environmental contaminants under UV and visible light irradiation. In this work, we devise a facile, cost-effective technique to in situ synthesize hierarchical SiO 2 @C-doped TiO 2 (SCT) hollow spheres for the first time. This strategy mainly contains the preparation of monodisperse cationic polystyrene spheres (CPS), sequential deposition of inner SiO 2 , the preparation of the sandwich-like CPS@SiO 2 @CPS particles, and formation of outer TiO 2 . After the one-step removal of CPS templates by calcination at 450°C, hierarchical SiO 2 @C-doped TiO 2 hollow spheres are in situ prepared. The morphology, hierarchical structure, and properties of SCT photocatalyst were characterized by TEM. SEM, STEM Mapping, BET, XRD, UV-vis spectroscopy, and XPS. Results strongly confirm the carbon doping in the outer TiO 2 lattice of SCT hollow spheres. When the as-synthesized SCT hollow spheres were employed as a photocatalyst for the degradation of Rhodamine B under visible-light and ultraviolet irradiation, the SCT photocatalyst exhibits a higher photocatalytic activity than commercial P25, effectively overcoming the limitations of poorer UV activity for many previous reported TiO 2 -based photocatalysts due to doping. Copyright © 2017 Elsevier B.V. All rights reserved.

Hierarchical FeTiO3-TiO2 hollow spheres for efficient simulated sunlight-driven water oxidation.

Science.gov (United States)

Han, Taoran; Chen, Yajie; Tian, Guohui; Wang, Jian-Qiang; Ren, Zhiyu; Zhou, Wei; Fu, Honggang

2015-10-14

Oxygen generation is the key step for the photocatalytic overall water splitting and considered to be kinetically more challenging than hydrogen generation. Here, an effective water oxidation catalyst of hierarchical FeTiO3-TiO2 hollow spheres are prepared via a two-step sequential solvothermal processes and followed by thermal treatment. The existence of an effective heterointerface and built-in electric field in the surface space charge region in FeTiO3-TiO2 hollow spheres plays a positive role in promoting the separation of photoinduced electron-hole pairs. Surface photovoltage, transient-state photovoltage, fluorescence and electrochemical characterization are used to investigate the transfer process of photoinduced charge carriers. The photogenerated charge carriers in the hierarchical FeTiO3-TiO2 hollow spheres with a proper molar ratio display much higher separation efficiency and longer lifetime than those in the FeTiO3 alone. Moreover, it is suggested that the hierarchical porous hollow structure can contribute to the enhancement of light utilization, surface active sites and material transportation through the framework walls. This specific synergy significantly contributes to the remarkable improvement of the photocatalytic water oxidation activity of the hierarchical FeTiO3-TiO2 hollow spheres under simulated sunlight (AM1.5).

Template synthesis of highly crystalline and monodisperse iron oxide pigments of nanosize

International Nuclear Information System (INIS)

Sreeram, Kalarical Janardhanan; Indumathy, Ramasamy; Rajaram, Ananthanarayanan; Nair, Balachandran Unni; Ramasami, Thirumalachari

2006-01-01

Synthesis of highly crystalline and monodisperse iron oxide nanoparticles is reported. The separation of Fe centers through site-specific binding to a polysaccharide-alginate matrix enables the generation of particles with a monodisperse or narrow size distribution character, resulting in transparent pigments. Site-specific interactions coupled with gel like character of alginate is proposed as the mechanism behind generation of lower particle sizes. Alginate-Fe complexes developed were subjected to heat treatment to provide for crystalline character and development of hematite (α-Fe 2 O 3 ). Conditions most ideal for achieving monodispersity and lower sizes have been optimized and confirmed through microscopic and photon correlation spectroscopic measurements

Laser ablation synthesis of monodispersed magnetic alloy nanoparticles

International Nuclear Information System (INIS)

Seto, Takafumi; Koga, Kenji; Akinaga, Hiroyuki; Takano, Fumiyoshi; Orii, Takaaki; Hirasawa, Makoto

2006-01-01

Monodispersed CoPt alloy nanoparticles were synthesized by a pulsed laser ablation (PLA) technique coupled with a low-pressure operating differential mobility analyzer (LP-DMA). The CoPt alloy nanoparticles were generated by laser ablating a solid Co-Pt target. In CoPt alloy nanoparticles synthesized from a target with a Co composition of 75 at%, the nanoparticle surfaces were covered by an oxide layer and exhibited a core-shell structure. In contrast, no shell was observed in particles generated from a target with a Co:Pt ratio of 50:50 at%. According to an EDX analysis, the compositions of the individual nanoparticles were almost the same as that of the target material. Finally, the magnetic hysteresis loops of the CoPt alloy nanoparticles exhibited ferromagnetism

Laser ablation synthesis of monodispersed magnetic alloy nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Seto, Takafumi, E-mail: t.seto@aist.go.jp; Koga, Kenji; Akinaga, Hiroyuki; Takano, Fumiyoshi; Orii, Takaaki; Hirasawa, Makoto [National Institute of Advanced Industrial Science and Technology (AIST), Research Consortium for Synthetic Nano-Function Materials Project (SYNAF) (Japan)

2006-08-15

Monodispersed CoPt alloy nanoparticles were synthesized by a pulsed laser ablation (PLA) technique coupled with a low-pressure operating differential mobility analyzer (LP-DMA). The CoPt alloy nanoparticles were generated by laser ablating a solid Co-Pt target. In CoPt alloy nanoparticles synthesized from a target with a Co composition of 75 at%, the nanoparticle surfaces were covered by an oxide layer and exhibited a core-shell structure. In contrast, no shell was observed in particles generated from a target with a Co:Pt ratio of 50:50 at%. According to an EDX analysis, the compositions of the individual nanoparticles were almost the same as that of the target material. Finally, the magnetic hysteresis loops of the CoPt alloy nanoparticles exhibited ferromagnetism.

Monodisperse colloidal spheres for (Y,Eu2O3 red-emitting phosphors: establishment of processing window and size-dependent luminescence behavior

Directory of Open Access Journals (Sweden)

Qi Zhu, Ji-Guang Li, Xiaodong Li, Xudong Sun and Yoshio Sakka

2011-01-01

Full Text Available The urea-based homogeneous precipitation method was introduced in the preparation of monodisperse colloidal spheres for (Y0.95Eu0.052O3 red-emitting phosphors, and the processing window was defined. Particle size and shape are significantly affected by the ion concentration and the urea/RE3+ molar ratio R (RE3+=Y3++Eu3+. A low ion concentration is beneficial in forming monodisperse spheres and extending their formation domain. Increasing R results in a gradual change in the composition of spherical particles from the core-shell Eu(OHCO3@Y(OHCO3 structure to a homogeneous solid solution, thereby significantly lowering the calcination temperature at which precursors convert to oxides. Upon UV excitation into the charge-transfer band at 254 nm, the uniform phosphor spheres of (Y0.95Eu0.052O3 exhibit typical red emissions at 613 nm; the emission is stronger from larger particles mainly because of their smaller surface area. Both the luminescence intensity and quantum efficiency of the oxide phosphors increase with elevated calcination temperatures. The spherical shape and excellent dispersion of the precursor particles (~450 nm in diameter have been well retained after calcination at 1000 circleC for 4 h, and the resultant oxide phosphors exhibit external and internal quantum efficiencies of 50 and 82%, respectively.

Catalytic pyrolysis of microalgae to high-quality liquid bio-fuels

International Nuclear Information System (INIS)

Babich, I.V.; Hulst, M. van der; Lefferts, L.; Moulijn, J.A.; O'Connor, P.; Seshan, K.

2011-01-01

The pyrolytic conversion of chlorella algae to liquid fuel precursor in presence of a catalyst (Na 2 CO 3 ) has been studied. Thermal decomposition studies of the algae samples were performed using TGA coupled with MS. Liquid oil samples were collected from pyrolysis experiments in a fixed-bed reactor and characterized for water content and heating value. The oil composition was analyzed by GC-MS. Pretreatment of chlorella with Na 2 CO 3 influences the primary conversion of chlorella by shifting the decomposition temperature to a lower value. In the presence of Na 2 CO 3 , gas yield increased and liquid yield decreased when compared with non-catalytic pyrolysis at the same temperatures. However, pyrolysis oil from catalytic runs carries higher heating value and lower acidity. Lower content of acids in the bio-oil, higher aromatics, combined with higher heating value show promise for production of high-quality bio-oil from algae via catalytic pyrolysis, resulting in energy recovery in bio-oil of 40%. -- Highlights: → The pyrolytic catalytic conversion of chlorella algae to liquid fuel precursor. → Na 2 CO 3 as a catalyst for the primary conversion of chlorella. → Pyrolysis oil from catalytic runs carries higher heating value and lower acidity. → High-quality bio-oil from algae via catalytic pyrolysis with energy recovery in bio-oil of 40%.

Removal of Heavy Metals Pb2+, Cu2+, Zn2+, Cd2+, Ni2+, Co2+ and Fe3+ from Aqueous Solutions by using Xanthium Pensylvanicum

Directory of Open Access Journals (Sweden)

Jaber SALEHZADEH

2013-11-01

Full Text Available The hazardous ill effects of heavy metals on the environment and public health is a matter of serious concern. Biosorption is emerging as a sustainable effective technology. Heavy metals in water resources are one of the most important environmental problems of countries. The intensification of industrial activity and environmental stress greatly contributes to the significant rise of heavy metal pollution in water resources making threats on terrestrial and aquatic life. The toxicity of metal pollution is slow and interminable, as these metal ions are non bio-degradable. The adsorption capacity of Xanthium Pensylvanicum towards metal ions such as Pb2+, Cu2+, Zn2+, Cd2+, Ni2+, Co2+ and Fe3+, was studied. The adsorption capacity was performed by batch experiments as a function of process parameters (such as sorption time and pH. Experimental results showed that the removal percentages increasing of metal ions at pH=4, initial concentration of metal ions 10 mg/L, and after 90 min of shaking was: Zn2+ < Cd2+ < Cu2+ < Pb2+ < Ni2+ < Fe3+ < Co2+.

Mesoporous Co{sub 3}O{sub 4} and CoO rate at C topotactically transformed from chrysanthemum-like Co(CO{sub 3}){sub 0.5}(OH).0.11H{sub 2}O and their lithium-storage properties

Energy Technology Data Exchange (ETDEWEB)

Xiong, Shenglin; Zeng, Hua Chun [Department of Chemical and Biomolecular Engineering, KAUST-NUS GCR Program, Faculty of Engineering, National University of Singapore, 10 Kent Ridge Crescent, Singapore (Singapore); Chen, Jun Song; Lou, Xiong Wen [School of Chemical and Biomedical Engineering, Nanyang Technological University, 70 Nanyang Drive, Singapore (Singapore)

2012-02-22

In this work, a novel hydrothermal route is developed to synthesize cobalt carbonate hydroxide, Co(CO{sub 3}){sub 0.5}(OH).0.11H{sub 2}O. In this method, sodium chloride salt is utilized to organize single-crystalline nanowires into a chrysanthemum-like hierarchical assembly. The morphological evolution process of this organized product is investigated by examining different reaction intermediates during the synthesis. The growth and thus the final assembly of the Co(CO{sub 3}){sub 0.5}(OH).0.11H{sub 2}O can be finely tuned by selecting preparative parameters, such as the molar ratio of the starting chemicals, the additives, the reaction time and the temperature. Using the flower-like Co(CO{sub 3}){sub 0.5}(OH).0.11H{sub 2}O as a solid precursor, quasi-single-crystalline mesoporous Co{sub 3}O{sub 4} nanowire arrays are prepared via thermal decomposition in air. Furthermore, carbon can be added onto the spinel oxide by a chemical-vapor-deposition method using acetylene, which leads to the generation of carbon-sheathed CoO nanowire arrays (CoO rate at C). Through comparing and analyzing the crystal structures, the resultant products and their high crystallinity can be explained by a sequential topotactic transformation of the respective precursors. The electrochemical performances of the typical cobalt oxide products are also evaluated. It is demonstrated that tuning of the surface texture and the pore size of the Co{sub 3}O{sub 4} products is very important in lithium-ion-battery applications. The carbon-decorated CoO nanowire arrays exhibit an excellent cyclic performance with nearly 100% capacity retention in a testing range of 70 cycles. Therefore, this CoO rate at C nanocomposite can be considered to be an attractive candidate as an anode material for further investigation. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Fabrication of α-Fe{sub 2}O{sub 3}/TiO{sub 2} bi-functional composites with hierarchical and hollow structures and their application in water treatment

Energy Technology Data Exchange (ETDEWEB)

Li, Yinhui, E-mail: lillian09281@hotmail.com; Zhang, Na; Chen, Jianxin, E-mail: chjx2000@126.com; Li, Ruijuan; Li, Liang; Li, Kunyu [Hebei University of Technology, School of Marine Science and Engineering, Engineering Research Center of Seawater Utilization Technology, Ministry of Education (China)

2016-02-15

The α-Fe{sub 2}O{sub 3}/TiO{sub 2} bi-functional composites with hierarchical and hollow structures are fabricated through a hydrothermal route. The adsorption performance and photocatalytic activity of the composites towards Pb{sup 2+} are investigated in this work. Different adsorption kinetics models and equilibrium models are used to explore the adsorption behavior of hierarchical α-Fe{sub 2}O{sub 3}/TiO{sub 2} hollow spheres. Experimental data show that adsorption kinetics of the hierarchical α-Fe{sub 2}O{sub 3}/TiO{sub 2} hollow spheres can be fitted well by the pseudo-second-order model, while the isothermal data can be perfectly described by the Langmuir adsorption model. The maximum adsorption capacity of the hierarchical α-Fe{sub 2}O{sub 3}/TiO{sub 2} hollow spheres is 32.36 mg g{sup −1}. Moreover, the hierarchical α-Fe{sub 2}O{sub 3}/TiO{sub 2} hollow spheres possess photocatalytic oxidation character under simulated solar light irradiation. The results demonstrate that the hierarchical α-Fe{sub 2}O{sub 3}/TiO{sub 2} hollow spheres, as effective and cheap materials, can be applied to the removal of heavy metal ions from wastewater.

Self-Assembled Hierarchical Formation of Conjugated 3D Cobalt Oxide Nanobead-CNT-Graphene Nanostructure Using Microwaves for High-Performance Supercapacitor Electrode.

Science.gov (United States)

Kumar, Rajesh; Singh, Rajesh Kumar; Dubey, Pawan Kumar; Singh, Dinesh Pratap; Yadav, Ram Manohar

2015-07-15

Here we report the electrochemical performance of a interesting three-dimensional (3D) structures comprised of zero-dimensional (0D) cobalt oxide nanobeads, one-dimensional (1D) carbon nanotubes and two-dimensional (2D) graphene, stacked hierarchically. We have synthesized 3D self-assembled hierarchical nanostructure comprised of cobalt oxide nanobeads (Co-nb), carbon nanotubes (CNTs), and graphene nanosheets (GNSs) for high-performance supercapacitor electrode application. This 3D self-assembled hierarchical nanostructure Co3O4 nanobeads-CNTs-GNSs (3D:Co-nb@CG) is grown at a large scale (gram) through simple, facile, and ultrafast microwave irradiation (MWI). In 3D:Co-nb@CG nanostructure, Co3O4 nanobeads are attached to the CNT surfaces grown on GNSs. Our ultrafast, one-step approach not only renders simultaneous growth of cobalt oxide and CNTs on graphene nanosheets but also institutes the intrinsic dispersion of carbon nanotubes and cobalt oxide within a highly conductive scaffold. The 3D:Co-nb@CG electrode shows better electrochemical performance with a maximum specific capacitance of 600 F/g at the charge/discharge current density of 0.7A/g in KOH electrolyte, which is 1.56 times higher than that of Co3O4-decorated graphene (Co-np@G) nanostructure. This electrode also shows a long cyclic life, excellent rate capability, and high specific capacitance. It also shows high stability after few cycles (550 cycles) and exhibits high capacitance retention behavior. It was observed that the supercapacitor retained 94.5% of its initial capacitance even after 5000 cycles, indicating its excellent cyclic stability. The synergistic effect of the 3D:Co-nb@CG appears to contribute to the enhanced electrochemical performances.

Synthesis and structural characterization of two cobalt phosphites: 1-D (H3NC6H4NH3)Co(HPO3)2 and 2-D (NH4)2Co2(HPo3)3

International Nuclear Information System (INIS)

Cheng, C.-C.; Chang, W.-K.; Chiang, R.-K.; Wang, S.-L.

2010-01-01

Two new cobalt phosphites, (H 3 NC 6 H 4 NH 3 )Co(HPO 3 ) 2 (1) and (NH 4 ) 2 Co 2 (HPO 3 ) 3 (2), have been synthesized and characterized by single-crystal X-ray diffraction. All the cobalt atoms of 1 are in tetrahedral CoO 4 coordination. The structure of 1 comprises twisted square chains of four-rings, which contain alternating vertex-shared CoO 4 tetrahedra and HPO 3 groups. These chains are interlinked with trans-1,4-diaminocyclohexane cations by hydrogen bonds. The 2-D structure of 2 comprises anionic complex sheets with ammonium cations present between them. An anionic complex sheet contains three-deck phosphite units, which are interconnected by Co 2 O 9 to form complex layers. Magnetic susceptibility measurements of 1 and 2 showed that they have a weak antiferromagnetic interaction. - Graphical abstract: The 2-D structure of (NH 4 ) 2 Co 2 (HPO 3 ) 3 comprises anionic complex sheets with ammonium cations present between them. An anionic complex sheet contains three-deck phosphite units, which are interconnected by dimmeric Co 2 O 9 to form complex layers.

Toxicity of inhaled 239PuO2 in Beagle dogs: A. Monodisperse 0.75-μm AMAD particles. B. Monodisperse 1.5-μm AMAD particles. C. Monodisperse 3.0--μm AMAD particles. XI

International Nuclear Information System (INIS)

Muggenburg, B.A.; Guilmette, R.A.; Hahn, F.F.; Boecker, B.B.; McClellan, R.O.

1988-01-01

Beagle dogs were exposed to monodisperse aerosols of 239 PuO 2 of 0.75, 1.5, or 30 μm activity median aerodynamic diameter (AMAD) to obtain information on the relative importance of homogeneity of alpha irradiation doses to the lung in producing biological effects. The dogs' initial pulmonary burdens (IPB) ranged from 0.0002-2.0 μCi (0.0074 to 74 kBq) 239 Pu/kg of body mass. Thirty-six dogs were exposed to the aerosol diluent as controls. Forty-two of 48 dogs exposed to 0.75 μm AMAD particles have died; 67 of 96 have died in the study involving 1.5 μm AMAD particles; and 62 of 72 have died in the study involving the 3.0 μm AMAD particles. Seven of 36 control dogs have died. Most dogs exposed to 239 Pu that have failed to survive have died with radiation pneumonitis and fibrosis and/or lung cancer. Surviving dogs have lived up to 4300 days after exposure. The data obtained to date indicate that the degree of uniformity of dose to the lung does not significantly modify the risk of lung cancer. (author)

Fabrication of hierarchical graphene@Fe3O4@SiO2@polyaniline quaternary composite and its improved electrochemical performance

International Nuclear Information System (INIS)

Wang, Lei; Zhu, Jianfeng; Yang, Haibo; Wang, Fen; Qin, Yi; Zhao, Ting; Zhang, Pei

2015-01-01

Highlights: • Graphene@Fe 3 O 4 @SiO 2 @polyaniline hierarchical structures have been fabricated. • The reflection loss of the composites is below −10 dB in 10.5–16.3 GHz. • The maximum absorption of the composites is −40.7 dB at 12.5 GHz. - Abstract: Hierarchical graphene@Fe 3 O 4 @SiO 2 @polyaniline quaternary composite is fabricated subtly. Their microwave absorption properties are also investigated in the 2–18 GHz frequency range. Transmission electron microscopy (TEM) and scanning electron microscope (SEM) reveal that Fe 3 O 4 @SiO 2 @polyaniline core@shell@shell heteronanostructures are densely covered on the surfaces of graphene, and form hierarchical structures. Compared with two-dimensional binary nanocomposites of graphene@Fe 3 O 4 , the hierarchical structure exhibits enhanced EM absorption in terms of both the maximum reflection loss value and the absorption bandwidth. The maximum reflection loss value can reach −40.7 dB at 12.5 GHz with a thickness of 2.5 mm and the bandwidth corresponding to the reflection loss below −10 dB is 5.8 GHz (from 10.5 to 16.3 GHz)

Thermodynamic modeling of NH_3-CO_2-SO_2-K_2SO_4-H_2O system for combined CO_2 and SO_2 capture using aqueous NH_3

International Nuclear Information System (INIS)

Qi, Guojie; Wang, Shujuan

2017-01-01

Highlights: • A new application of aqueous NH_3 based combined CO_2 and SO_2 process was proposed. • A thermodynamic model simulated the heat of absorption and the K_2SO_4 precipitation. • The CO_2 content can be regenerated in a stripper with lower heat of desorption. • The SO_2 content can be removed by K_2SO_4 precipitation from the lean NH_3 solvent. - Abstract: A new application of aqueous NH_3 based post-combustion CO_2 and SO_2 combined capture process was proposed to simultaneously capture CO_2 and SO_2, and remove sulfite by solid (K_2SO_4) precipitation method. The thermodynamic model of the NH_3-CO_2-SO_2-K_2SO_4-H_2O system for the combined CO_2 and SO_2 capture process was developed and validated in this work to analyze the heat of CO_2 and SO_2 absorption in the NH_3-CO_2-SO_2-H_2O system, and the K_2SO_4 precipitation characteristics in the NH_3-CO_2-SO_2-K_2SO_4-H_2O system. The average heat of CO_2 absorption in the NH_3-CO_2-H_2O system at 40 °C is around −73 kJ/mol CO_2 in 2.5 wt% NH_3 with CO_2 loading between 0.2 and 0.5 C/N. The average heat of SO_2 absorption in the NH_3-SO_2-H_2O system at 40 °C is around −120 kJ/mol SO_2 in 2.5 wt% NH_3 with SO_2 loading between 0 and 0.5 S/N. The average heat of CO_2 absorption in the NH_3-CO_2-SO_2-H_2O system at 40 °C is 77, 68, and 58 kJ/mol CO_2 in 2.5 wt% NH_3 with CO_2 loading between 0.2 and 0.5 C/N, when SO_2 loading is 0, 0.1, 0.2 S/N, respectively. The solubility of K_2SO_4 increases with temperature, CO_2 and SO_2 loadings, but decreases with NH_3 concentration in the CO_2 and SO_2 loaded aqueous NH_3. The thermodynamic evaluation indicates that the combined CO_2 and SO_2 capture process could employ the typical absorption/regeneration process to simultaneously capture CO_2 and SO_2 in an absorber, thermally desorb CO_2 in a stripper, and feasibly remove sulfite (oxidized to sulfate) content by precipitating K_2SO_4 from the lean NH_3 solvent after the lean/rich heat exchanger.

BioCichlid: central dogma-based 3D visualization system of time-course microarray data on a hierarchical biological network.

Science.gov (United States)

Ishiwata, Ryosuke R; Morioka, Masaki S; Ogishima, Soichi; Tanaka, Hiroshi

2009-02-15

BioCichlid is a 3D visualization system of time-course microarray data on molecular networks, aiming at interpretation of gene expression data by transcriptional relationships based on the central dogma with physical and genetic interactions. BioCichlid visualizes both physical (protein) and genetic (regulatory) network layers, and provides animation of time-course gene expression data on the genetic network layer. Transcriptional regulations are represented to bridge the physical network (transcription factors) and genetic network (regulated genes) layers, thus integrating promoter analysis into the pathway mapping. BioCichlid enhances the interpretation of microarray data and allows for revealing the underlying mechanisms causing differential gene expressions. BioCichlid is freely available and can be accessed at http://newton.tmd.ac.jp/. Source codes for both biocichlid server and client are also available.

Charcoal cuts the CO2-emissions

International Nuclear Information System (INIS)

Aakervik, Anne Lise.

1999-01-01

According to this article, bio carbon, or charcoal, may be the way out for the Norwegian processing industry in attempting to reduce the emission of carbon dioxide. Norwegian ferro-alloy plants emit 3 million ton carbon dioxide per year, which comes from the use of coal and coke as reducing agents in the smelting process. If the fraction of bio carbon is increased by 15%, the emission of CO 2 may be reduced by about 1/2 million tonne per year. But the price of charcoal is much greater than that of fix C from coal and coke. Research is in progress on trying to produce bio carbon cheaper. Charcoal can be produced from all types of forest by pyrolysis. Waste heat from the pyrolysis can be sold and used for district heating. The most expensive part in the use of bio carbon will be timber felling and transport to the log pile. Small-scale and large-scale tests will be made to see if it is possible to make adequate charcoal from subarctic timber

A General Synthesis Strategy for Hierarchical Porous Metal Oxide Hollow Spheres

Directory of Open Access Journals (Sweden)

Huadong Fu

2015-01-01

Full Text Available The hierarchical porous TiO2 hollow spheres were successfully prepared by using the hydrothermally synthesized colloidal carbon spheres as templates and tetrabutyl titanate as inorganic precursors. The diameter and wall thickness of hollow TiO2 spheres were determined by the hard templates and concentration of tetrabutyl titanate. The particle size, dispersity, homogeneity, and surface state of the carbon spheres can be easily controlled by adjusting the hydrothermal conditions and adding certain amount of the surfactants. The prepared hollow spheres possessed the perfect spherical shape, monodispersity, and hierarchically pore structures, and the further experiment verified that the present approach can be used to prepare other metal oxide hollow spheres, which could be used as catalysis, fuel cells, lithium-air battery, gas sensor, and so on.

A comparison of pipeline versus truck transport of bio-oil.

Science.gov (United States)

Pootakham, Thanyakarn; Kumar, Amit

2010-01-01

Biomass-based energy and fuels are receiving attention because they are considered carbon neutral; i.e. the amount of CO(2) released during combustion of this biomass is nearly the same as that taken up by the plants during their growth. Bio-oil is a dark viscous liquid consisting of hydrocarbons. These are produced by fast pyrolysis of biomass. "As-is" biomass material has a low energy density (MJ m(-3)), hence, the cost of transporting this energy is high. Bio-oil has a high energy density as compared to "as-is" biomass material, consequently it helps in reducing the cost of energy transport. This study compares the life cycle assessment of transportation of bio-oil by pipeline with that by truck. The scope of the work includes the transportation of bio-oil by truck or pipeline from a centralized plant (supplied with forest biomass) to an end-user. Two cases are studied for pipeline transport of bio-oil: the first case considers a coal-based electricity supply for pumping the bio-oil through a pipeline; the second case considers an electricity supply from a renewable resource. The two cases of pipeline transport are compared to two cases of truck transport (truck trailer and super B-train truck). The life cycle greenhouse gas (GHG) emissions from the pipeline transport of bio-oil for the two cases of electricity supply are 345 and 17 g of CO(2) m(-3) km(-1), respectively. Similar values for transport by trailer (capacity - 30 m(3)) and super B-train truck (capacity - 60 m(3)) are 89 and 60 g of CO(2) m(-3) km(-1), respectively. Energy input for bio-oil transport is 3.95 MJ m(-3) km(-1) by pipeline, 2.59 MJ m(-3) km(-1) by truck and 1.66 MJ m(-3) km(-1) by super B-train truck. The results show that GHG emissions in pipeline transport are largely dependent on the source of electricity (higher for coal-based electricity). Substituting 250 m(3) day(-1) of pipeline-transported bio-oil for coal-based electricity can mitigate about 5.1 million tonnes of CO(2) per year

Formation, stability and structural characterization of ternary MgUO{sub 2}(CO{sub 3}){sub 3}{sup 2-} and Mg{sub 2}UO{sub 2}(CO{sub 3}){sub 3}(aq) complexes

Energy Technology Data Exchange (ETDEWEB)

Lee, Jun-Yeop; Yun, Jong-Il [KAIST, Daejeon (Korea, Republic of). Dept. of Nuclear and Quantum Engineering; Vespa, Marika; Gaona, Xavier; Dardenne, Kathy; Rothe, Joerg; Rabung, Thomas; Altmaier, Marcus [Karlsruhe Institute of Technology, Karlsruhe (Germany). Inst. for Nuclear Waste Disposal

2017-06-01

The formation of ternary Mg-UO{sub 2}-CO{sub 3} complexes under weakly alkaline pH conditions was investigated by time-resolved laser fluorescence spectroscopy (TRLFS) and extended X-ray absorption fine structure (EXAFS) and compared to Ca-UO{sub 2}-CO{sub 3} complexes. The presence of two different Mg-UO{sub 2}-C{sub 3} complexes was identified by means of two distinct fluorescence lifetimes of 17±2 ns and 51±2 ns derived from the multi-exponential decay of the fluorescence signal. Slope analysis in terms of fluorescence intensity coupled with fluorescence intensity factor as a function of log [Mg(II)] was conducted for the identification of the Mg-UO{sub 2}-CO{sub 3} complexes forming. For the first time, the formation of both MgUO{sub 2}(CO{sub 3}){sub 3}{sup 2-} and Mg{sub 2}UO{sub 2}(CO{sub 3}){sub 3}(aq) species was confirmed and the corresponding equilibrium constants were determined as log β {sub 113}=25.8±0.3 and β {sub 213}=27.1±0.6, respectively. Complementarily, fundamental structural information for both Ca-UO{sub 2}-CO{sub 3} and Mg-UO{sub 2}-CO{sub 3} complexes was gained by extended EXAFS revealing very similar structures between these two species, except for the clearly shorter U-Mg distance (3.83 Aa) compared with U-Ca distance (4.15 Aa). These results confirmed the inner-sphere character of the Ca/Mg-UO{sub 2}-CO{sub 3} complexes. The formation constants determined for MgUO{sub 2}(CO{sub 3}){sub 3}{sup 2-} and Mg{sub 2}UO{sub 2}(CO{sub 3}){sub 3}(aq) species indicate that ternary Mg-UO{sub 2}-CO{sub 3} complexes contribute to the relevant uranium species in carbonate saturated solutions under neutral to weakly alkaline pH conditions in the presence of Mg(II) ions, which will induce notable influences on the U(VI) chemical species under seawater conditions.

Hydrogen production by steam reforming of bio-oil aqueous fraction over Co-Fe/ZSM-5

Science.gov (United States)

Chen, Mingqiang; Wang, Yishuang; Liang, Tian; Yang, Zhonglian

2018-02-01

A series of Co-Fe/ZSM-5 catalysts were prepared by impregnation method and their catalytic performance under steam reforming bio-oil aqueous fraction (SRBAF). The as-prepared catalysts were characterized by XRD, BET, and SEM. The characterization results revealed the Co-Fe alloy phase was formed in Co0.5Fe0.5/ZSM-5 catalyst, and this catalyst exhibited unique pore volume (0.28 cm3/g) and pore size (8.4 nm). The results of experiment demonstrated the addition of Fe species could significantly increase C conversion and H2 yield, and the formation of Co-Fe alloy effectively inhibited methanation reaction and improved water-gas shift (WGS) reaction. The highest H2 yield (81%) and C conversion (85%) was obtained at the following reaction conditions: 2.5 g of C0.5F0.5/Z catalyst, T = 700 °C, S/C = 10-14,.feed flow rate was 10.0 gbio-oil/h, N2 flow rate was 0.16 L/min.

Influence of particle sizes on the electronic behavior of Zn{sub x}Co{sub 1−x}Fe{sub 2}O{sub 4} spinels (x = 0.2, 0.3)

Energy Technology Data Exchange (ETDEWEB)

Viñas, R. [Departamento de Química Inorgánica, Facultad de Ciencias Químicas, Universidad Complutense de Madrid, Avda. Complutense s/n, 28040 Madrid (Spain); Álvarez-Serrano, I., E-mail: ias@quim.ucm.es [Departamento de Química Inorgánica, Facultad de Ciencias Químicas, Universidad Complutense de Madrid, Avda. Complutense s/n, 28040 Madrid (Spain); López, M.L.; Pico, C.; Veiga, M.L. [Departamento de Química Inorgánica, Facultad de Ciencias Químicas, Universidad Complutense de Madrid, Avda. Complutense s/n, 28040 Madrid (Spain); Mompeán, F.; García-Hernández, M. [Instituto de Ciencia de Materiales, CSIC, Sor Juana Inés de la Cruz, 3, 28049 Madrid (Spain)

2014-07-15

Graphical abstract: Relaxor ferroelectric behavior and superparamagnetism in nanoparticles of Zn{sub x}Co{sub 1−x}Fe{sub 2}O{sub 4} obtained in supercritical water. - Highlights: • Title ferrites were prepared by hydrothermal techniques (sub and supercritical). • In supercritical (SCW) conditions highly monodispersive samples were obtained. • All samples are semiconductors; n-type or p-type response depends on the composition. • Superparamagnetic and relaxor ferroelectric response coexist in SCW samples. - Abstract: The effect of composition and particle size on the electrical and magnetic behavior of Zn{sub x}Co{sub 1−x}Fe{sub 2}O{sub 4} spinels (x = 0.2 and 0.3) has been studied. Powdered samples of these ferrites have been synthetized by the liquid mix technique and hydrothermal method (in sub and supercritical conditions), leading to average particle sizes of ca. 50 and 10 nm, respectively. They have been characterized by means of X-ray diffraction, Thermogravimetric analysis, Energy-Dispersive X-ray Spectroscopy and impedance and magnetic measurements. Permittivity values up to ca. 500 were registered at 375 K, which remained almost constant at moderate frequencies, between 10{sup 3} and 10{sup 6} Hz. Stabilization of polarization phenomena is very sensitive to grain size and composition. Dielectric behavior evolves to a relaxor ferroelectric response when grain size becomes nanometric and, particularly, when the sample shows high monodispersion. The conduction mechanism and type of majority charge carriers have been established from Seebeck measurements. The x = 0.3 sample, prepared in supercritical water for the first time, exhibits homogeneous particle size distribution, superparamagnetic behavior and Curie temperature lower than those corresponding to similar microsized samples. The electronic response of the ferrites obtained in supercritical conditions is interpreted considering the possible short scale polarization of nanodomains.

Mesoporous titanium dioxide (TiO2) with hierarchically 3D dendrimeric architectures: formation mechanism and highly enhanced photocatalytic activity.

Science.gov (United States)

Li, Xiao-Yun; Chen, Li-Hua; Rooke, Joanna Claire; Deng, Zhao; Hu, Zhi-Yi; Wang, Shao-Zhuan; Wang, Li; Li, Yu; Krief, Alain; Su, Bao-Lian

2013-03-15

Mesoporous TiO(2) with a hierarchically 3D dendrimeric nanostructure comprised of nanoribbon building units has been synthesized via a spontaneous self-formation process from various titanium alkoxides. These hierarchically 3D dendrimeric architectures can be obtained by a very facile, template-free method, by simply dropping a titanium butoxide precursor into methanol solution. The novel configuration of the mesoporous TiO(2) nanostructure in nanoribbon building units yields a high surface area. The calcined samples show significantly enhanced photocatalytic activity and degradation rates owing to the mesoporosity and their improved crystallinity after calcination. Furthermore, the 3D dendrimeric architectures can be preserved after phase transformation from amorphous TiO(2) to anatase or rutile, which occurs during calcination. In addition, the spontaneous self-formation process of mesoporous TiO(2) with hierarchically 3D dendrimeric architectures from the hydrolysis and condensation reaction of titanium butoxide in methanol has been followed by in situ optical microscopy (OM), revealing the secret on the formation of hierarchically 3D dendrimeric nanostructures. Moreover, mesoporous TiO(2) nanostructures with similar hierarchically 3D dendrimeric architectures can also be obtained using other titanium alkoxides. The porosities and nanostructures of the resultant products were characterized by SEM, TEM, XRD, and N(2) adsorption-desorption measurements. The present work provides a facile and reproducible method for the synthesis of novel mesoporous TiO(2) nanoarchitectures, which in turn could herald the fabrication of more efficient photocatalysts. Copyright © 2012 Elsevier Inc. All rights reserved.

Hierarchical silica particles by dynamic multicomponent assembly

DEFF Research Database (Denmark)

Wu, Z. W.; Hu, Q. Y.; Pang, J. B.

2005-01-01

Abstract: Aerosol-assisted assembly of mesoporous silica particles with hierarchically controllable pore structure has been prepared using cetyltrimethylammonium bromide (CTAB) and poly(propylene oxide) (PPO, H[OCH(CH3)CH2],OH) as co-templates. Addition of the hydrophobic PPO significantly...... influences the delicate hydrophilic-hydrophobic balance in the well-studied CTAB-silicate co-assembling system, resulting in various mesostructures (such as hexagonal, lamellar, and hierarchical structure). The co-assembly of CTAB, silicate clusters, and a low-molecular-weight PPO (average M-n 425) results...... in a uniform lamellar structure, while the use of a high-molecular-weight PPO (average M-n 2000), which is more hydrophobic, leads to the formation of hierarchical pore structure that contains meso-meso or meso-macro pore structure. The role of PPO additives on the mesostructure evolution in the CTAB...

Aerosol fabrication methods for monodisperse nanoparticles

Science.gov (United States)

Jiang, Xingmao; Brinker, C Jeffrey

2014-10-21

Exemplary embodiments provide materials and methods for forming monodisperse particles. In one embodiment, the monodisperse particles can be formed by first spraying a nanoparticle-containing dispersion into aerosol droplets and then heating the aerosol droplets in the presence of a shell precursor to form core-shell particles. By removing either the shell layer or the nanoparticle core of the core-shell particles, monodisperse nanoparticles can be formed.

Preparation and properties of hybrid monodispersed magnetic α-Fe2O3 based chitosan nanocomposite film for industrial and biomedical applications.

Science.gov (United States)

Singh, Jay; Srivastava, M; Dutta, Joydeep; Dutta, P K

2011-01-01

In this study, hydrothermally prepared magnetic α-Fe2O3 nanoparticles were dispersed in chitosan (CH) solution to fabricate nanocomposite film. X-ray diffraction (XRD) patterns indicated that the α-Fe2O3 nanoparticles were pure α-Fe2O3 with rhombohedral structures, and the fabrication of CH did not result in a phase change. The scanning electron microscopy (SEM) and transmission electron microscope (TEM) results showed that the hexagonal and spherical monodispersed α-Fe2O3 nanoparticles were encapsulated into the spherical dumb shaped CH-α-Fe2O3 nanocomposite film with a mean diameter of ∼87 and ∼110 nm respectively. The α-Fe2O3 nanoparticles and CH-α-Fe2O3 nanocomposite film were also characterized by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and vibrating sample magnetometer (VSM). Magnetic measurements revealed that the saturated magnetization (Ms) and remanent magnetization (Mr) of the pure α-Fe2O3 nanoparticles reached 0.573 emu/g and 0.100 emu/g respectively and the nanoparticles showed the characteristics of weak ferromagnetic before and after coating with CH. Copyright © 2010 Elsevier B.V. All rights reserved.

Controllable synthesis and upconversion emission of ultrasmall near-monodisperse lanthanide-doped Sr2LaF7 nanocrystals

International Nuclear Information System (INIS)

Mao, Yifu; Ma, Mo; Gong, Lunjun; Xu, Changfu; Ren, Guozhong; Yang, Qibin

2014-01-01

Highlights: • Apropos NaOH content facilitates the growth of pure phase Sr 2 LaF 7 NCs. • Yb 3+ doping is favorable to the formation of Sr 2 LaF 7 NCs with uniform size. • Ultrasmall near-monodispersed Sr 2 LaF 7 NCs(sub-10 nm) were synthesized for the first time. • Intense multicolor upconversion can be obtained by properly lanthanide doping. - Abstract: Fluorite phase Sr 2 LaF 7 nanocrystals (NCs) were synthesized via solvothermal method using oleic acid as capping ligands. The effects of preparing conditions on the phase structure, crystal size, morphology, and upconversion (UC) emission properties of the products were studied. The results reveal that just apropos NaOH content facilitates the growth of near-monodispersed pure phase Sr 2 LaF 7 NCs, and Yb 3+ doping is favorable to the formation of pure Sr 2 LaF 7 phase with more uniform size distribution. The average crystalline size of the products can be controlled less than 10 nm. Following appropriate lanthanide ions doping, the NCs show intense blue, yellow, and white-color UC emission under the excitation of a 980 nm laser. The energy transfer UC mechanisms for the fluorescent intensity were also investigated

Synthesis, characterization and magnetic property of maghemite (γ-Fe{sub 2}O{sub 3}) nanoparticles and their protective coating with pepsin for bio-functionalization

Energy Technology Data Exchange (ETDEWEB)

Bandhu, A.; Sutradhar, S.; Mukherjee, S. [Solid State Research Laboratory, Department of Physics, Burdwan University, Burdwan 713104, West Bengal (India); Greneche, J.M. [Laboratoire de Physique de l’Etat Condensé – UMR CNRS 6087, Université du Maine, 72085, Le Mans Cedex 9 (France); Chakrabarti, P.K., E-mail: pabitra_c@hotmail.com [Solid State Research Laboratory, Department of Physics, Burdwan University, Burdwan 713104, West Bengal (India)

2015-10-15

Highlights: • Maghemite nanoparticles were prepared by a modified co-precipitation method. • Nanoparticles were then successfully coated with pepsin for bio-functionlization. • XRD and Mössbauer spectra confirmed the maghemite phase of the nanoparticles. • Magnetic data were analysed to evaluate particle size, anisotropy etc. - Abstract: Maghemite nanoparticles (γ-Fe{sub 2}O{sub 3}) are prepared by co-precipitation method. To obtain bio-functionalized magnetic nanoparticles for magnetically controlled drug delivery, the prepared nanoparticles are successfully coated with pepsin, a bio-compatible polymer and digestive enzyme. Crystallographic phase of the nanoparticles is confirmed by X-ray diffractograms (XRD), high resolution transmission electron microscopy (HRTEM) and {sup 57}Fe Mössbauer spectrometry. The average size of nanoparticles/nanocrystallites is estimated from the (3 1 1) peak of the XRD pattern using Debye–Scherrer formula. Results of HRTEM of coated and bare samples are in good agreement with those extracted from the XRD analysis. The dynamic magnetic properties are observed and different quantities viz., coercive field, magnetization, remanence, hysteresis losses etc., are estimated, which confirmed the presence of superparamagnetic relaxation of nanoparticles. Mössbauer spectra of the samples recorded at both 300 and 77 K, confirmed that the majority of particles are maghemite together with a very small fraction of magnetite nanoparticles.

Toxicity of inhaled 238PuO2 in Beagle dogs: A. Monodisperse 1.5 μm AMAD particles. B. Monodisperse 3.0 μm particles. XV

International Nuclear Information System (INIS)

Mewhinney, J.A.; Gillett, N.A.; Muggenburg, B.A.; Hahn, F.F.; Diel, J.H.; Mauderly, J.L.; Boecker, B.B.; McClellan, R.O.

1988-01-01

Beagle dogs inhaled one of two sizes of monodisperse aerosols of 238 PuO 2 that resulted in graded levels of 238 Pu in the lung. All dogs are being studied for their life span. One hundred and thirty-seven dogs that had initial lung burdens ranging from 0.01 to 1.5 μCi 238 Pu/kg body weight (0.37 to 56 kBq/kg) have died, 8 with radiation pneumonitis and pulmonary fibrosis, 8 with lung tumors, 88 with bone tumors, 10 with liver tumors, and 25 of miscellaneous causes. Eighteen control dogs have died. Observations are being continued on 8 exposed and 6 control dogs alive at 4577-5274 days after exposure. (author)

Synthesis, characterization, and application of Zn(NH 3)(CO3) for selective adsorptive separation of CO2

Science.gov (United States)

Khazeni, Naasser

This study explores the potential of Zn(NH3)(CO3) for selective CO2 separation. It develops a novel, highly controllable, single-pot synthesis approach based on urea hydrolysis and solvothermal aging to increase the feasibility of synthesizing Zn(NH3)(CO3), determines the structure of Zn(NH3)(CO3) in detail through single crystal X-ray diffraction and powder X-ray diffraction analyses, and performs adsorption analyses for the compound using CO2, N 2, H2, O2, and CH4 as adsorptives. Through adsorptive characterization, a systematic adsorbent selection screening is performed to assess the potential application of Zn(NH3)(CO 3) for adsorptive separation of CO2 from an upstream gas mixture of power generation, hydrogen production, and natural gas industries. Structural analysis shows Zn(NH3)(CO3) to have an inorganic helical framework that consists of a small helix of (ZnOCO) 2 and a large helix of (ZnOCO)4 with two ammines (NH 3) pendant from every other zinc. In terms of adsorption capacity and CO2 selectivity, Zn(NH3)(CO3) adsorbed 0.550 mmole/g CO2 at 293 K and 4500 mmHg, but only 0.047 mmole/g N 2, 0.084 mmole/g H2, 0.207 mmole/g 02, and 0.060 mmole/g CH4 at the same temperature and pressure. This behavior demonstrates considerable equilibrium selectivities - 36, 31, 63, and 11 - for separating CO2 from CH4, CO2 from H 2, CO2 from N2, and CO2 from 02, respectively. During adsorption, the pendant ammines act as the gates of check-valves: applied pressure opens the gates for adsorption; and during desorption, the gates are closed, trapping the adsorbates, until a reduction of pressure to near-atmospheric levels. Therefore, Zn(NH3)(CO3) exhibits low-pressure H3 or H4 hysteresis, indicating that the Zn(NH3)(CO3) framework can achieve gas storage at near-atmospheric pressures. Additionally, the compound proves structurally stable, with an adsorption decrease of 0.8% after 20 adsorption/desorption cycles - a factor that, considered with the other characteristics of Zn

Determination of the dissociation constant of molten Li/sub 2/CO/sub 3//Na/sub 2/CO/sub 3//K/sub 2/CO/sub 3/ using a stabilized zirconia oxide-ion indicator

Energy Technology Data Exchange (ETDEWEB)

Ito, Yasuhiko; Tsuru, Kiyoshi; Oishi, Jun; Miyazaki, Yoshinori; Kodama, Teruo

1985-09-01

An Li/sub 2/CO/sub 3//Na/sub 2/CO/sub 3//K/sub 2/CO/sub 3/ eutectic melt has been selected as an example of a molten-carbonate system and the suitability of a stabilized zirconia-air electrode as an oxide-ion concentration indicator for this melt has been confirmed. With this indicator, the dissociation constant of the reaction CO/sub 3//sup 2 -/(l)=CO/sub 2/(g)+O/sup 2 -/(l) in this melt has been determined to be Ksub(d)=P sub(CO/sub 2/) (O/sup 2 -/)=4.03 x 10/sup -3/ Pa at 873 K. Reproducible measurements were obtained throughout the experiment and this method might find further application in the study of reactions related to the oxide ion in carbonate melts. (orig.).

Effects of different petal thickness on gas sensing properties of flower-like WO3·H2O hierarchical architectures

International Nuclear Information System (INIS)

Zeng, Wen; Zhang, He; Wang, Zhongchang

2015-01-01

Graphical abstract: In this work, we prepare four different petal thicknesses of hierarchical WO 3 ·H 2 O architectures via a simple hydrothermal process, and systematically report their formation mechanisms and gas-sensing properties. - Highlights: • Flower-like WO 3 ·H 2 O architectures with different petal thickness were reported. • The WO 3 ·H 2 O sheet-flower sensor shows a significantly enhanced gas response. • A possible growth mechanism for the flower-like architectures is proposed. - Abstract: Hierarchical architectures consisting of two-dimensional (2D) nanostructures are of great interest for potential use in recent year. Here, we report the successful synthesis of four hierarchical tungsten oxide flower-like architectures via a simple yet facile hydrothermal method. The as-prepared WO 3 ·H 2 O hierarchical architectures are in fact assembled with numerous nanosheets or nanoplates. Through a comprehensive characterization of microstructures and morphologies of the as-prepared products, we find that petal thickness is a key factor for affecting gas-sensing performances. We further propose a possible growth mechanism for the four flower-like architectures. Moreover, gas-sensing measurements showed that the well-defined sheet-flower WO 3 ·H 2 O hierarchical architectures exhibited the excellent gas-sensing properties to ethanol owing to their largest amount of thin petal structures and pores

Hierarchical architectures of ZnS–In2S3 solid solution onto TiO2 nanofibers with high visible-light photocatalytic activity

International Nuclear Information System (INIS)

Liu, Chengbin; Meng, Deshui; Li, Yue; Wang, Longlu; Liu, Yutang; Luo, Shenglian

2015-01-01

Graphical abstract: A unique hierarchical architecture of ZnS–In 2 S 3 solid solution onto TiO 2 nanofibers was fabricated. The hierarchical heterostructures exhibit high visible light photocatalytic activity and outstanding recycling performance. - Highlights: • Novel hierarchical heterostructure of TiO 2 @ZnS–In 2 S 3 solid solution. • Efficient inhibition of ZnS–In 2 S 3 solid solution aggregation. • High visible light photocatalytic activity. • Highly stable recycling performance. - Abstract: A unique hierarchical architecture of ZnS–In 2 S 3 solid solution nanostructures onto TiO 2 nanofibers (TiO 2 @ZnS–In 2 S 3 ) has been successfully fabricated by simple hydrothermal method. The ZnS–In 2 S 3 solid solution nanostructures exhibit a diversity of morphologies: nanosheet, nanorod and nanoparticle. The porous TiO 2 nanofiber templates effectively inhibit the aggregation growth of ZnS–In 2 S 3 solid solution. The formation of ZnS–In 2 S 3 solid solution is proved by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) and the intimate contact between TiO 2 nanofibers and ZnS–In 2 S 3 solid solution favors fast transfer of photogenerated electrons. The trinary TiO 2 @ZnS–In 2 S 3 heterostructures exhibit high adsorption capacity and visible light photocatalytic activity for the degradation of rhodamine B dye (RhB), remarkably superior to pure TiO 2 nanofibers or binary structures (ZnS/TiO 2 nanofibers, In 2 S 3 /TiO 2 nanofibers and ZnS–In 2 S 3 solid solution). Under visible light irradiation the RhB photocatalytic degradation rate over TiO 2 @ZnS–In 2 S 3 heterostructures is about 16.7, 12.5, 6.3, 5.9, and 2.2 times that over pure TiO 2 nanofibers, ZnS nanoparticles, In 2 S 3 /TiO 2 nanofibers, ZnS/TiO 2 nanofibers, and ZnS-In 2 S 3 solid solution, respectively. Furthermore, the TiO 2 @ZnS–In 2 S 3 heterostructures show highly stable recycling performance

Scalable 2D Hierarchical Porous Carbon Nanosheets for Flexible Supercapacitors with Ultrahigh Energy Density.

Science.gov (United States)

Yao, Lei; Wu, Qin; Zhang, Peixin; Zhang, Junmin; Wang, Dongrui; Li, Yongliang; Ren, Xiangzhong; Mi, Hongwei; Deng, Libo; Zheng, Zijian

2018-03-01

2D carbon nanomaterials such as graphene and its derivatives, have gained tremendous research interests in energy storage because of their high capacitance and chemical stability. However, scalable synthesis of ultrathin carbon nanosheets with well-defined pore architectures remains a great challenge. Herein, the first synthesis of 2D hierarchical porous carbon nanosheets (2D-HPCs) with rich nitrogen dopants is reported, which is prepared with high scalability through a rapid polymerization of a nitrogen-containing thermoset and a subsequent one-step pyrolysis and activation into 2D porous nanosheets. 2D-HPCs, which are typically 1.5 nm thick and 1-3 µm wide, show a high surface area (2406 m 2 g -1 ) and with hierarchical micro-, meso-, and macropores. This 2D and hierarchical porous structure leads to robust flexibility and good energy-storage capability, being 139 Wh kg -1 for a symmetric supercapacitor. Flexible supercapacitor devices fabricated by these 2D-HPCs also present an ultrahigh volumetric energy density of 8.4 mWh cm -3 at a power density of 24.9 mW cm -3 , which is retained at 80% even when the power density is increased by 20-fold. The devices show very high electrochemical life (96% retention after 10000 charge/discharge cycles) and excellent mechanical flexibility. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hierarchical Cu2O foam/g-C3N4 photocathode for photoelectrochemical hydrogen production

Science.gov (United States)

Ma, Xinzhou; Zhang, Jingtao; Wang, Biao; Li, Qiuguo; Chu, Sheng

2018-01-01

Solar photoelectrochemical (PEC) hydrogen production is a promising way for solving energy and environment problems. Earth-abundant Cu2O is a potential light absorber for PEC hydrogen production. In this article, hierarchical porous Cu2O foams are prepared by thermal oxidation of the electrochemically deposited Cu foams. PEC performances of the Cu2O foams are systematically studied and discussed. Benefiting from their higher light harvesting and more efficient charge separation, the Cu2O foams demonstrate significantly enhanced photocurrents and photostability compared to their film counterparts. Moreover, by integrating g-C3N4, hierarchical Cu2O foam/g-C3N4 composites are prepared with further improved photocurrent and photostability, appearing to be potential photocathodes for solar PEC hydrogen production. This study may provide a new and useful insight for the development of Cu2O-based photocathodes for PEC hydrogen production.

Free-standing and porous hierarchical nanoarchitectures constructed with cobalt cobaltite nanowalls for supercapacitors with high specific capacitances

Science.gov (United States)

Xiao, Yuanhua; Zhang, Aiqin; Liu, Shaojun; Zhao, Jihong; Fang, Shaoming; Jia, Dianzeng; Li, Feng

2012-12-01

Free-standing and porous hierarchical nanoarchitectures constructed with cobalt cobaltite (Co3O4) nanowalls have been successfully synthesized in large scale by calcining three dimensional (3D) hierarchical nanostructures consisting of single crystalline cobalt carbonate hydroxide hydrate - Co(CO3)0.5(OH)·0.11H2O nanowalls prepared with a solvothermal method. The step-by-step decomposition of the precursor can generate porous Co3O4 nanowalls with BET surface area of 88.34 m2 g-1. The as-prepared Co3O4 nanoarchitectures show superior specific capacitance to the most Co3O4 supercapacitor electrode materials to date. After continuously cycled for 1000 times of charge-discharge at 4 A g-1, the supercapacitors can retain ca 92.3% of their original specific capacitances. The excellent performances of the devices can be attributed to the porous and hierarchical 3D nanostructure of the materials.

Optimization Of Process Parameters For The Production Of Bio diesel From Waste Cooking Oil In The Presence Of Bifunctional γ-Al2O3-CeO2 Supported Catalysts

International Nuclear Information System (INIS)

Anita Ramli; Muhammad Farooq

2015-01-01

Huge quantities of waste cooking oils are produced all over the world every day, especially in the developed countries with 0.5 million ton per year waste cooking oil are being generated in Malaysia alone. Such large amount of waste cooking oil production can create disposal problems and contamination to water and land resources if not disposed properly. The use of waste cooking oil as feedstock for bio diesel production will not only avoid the competition of the same oil resources for food and fuel but will also overcome the waste cooking oil disposal problems. However, waste cooking oil has high acid value, thus would require the oil to undergo esterification with an acid catalyst prior to transesterification with a base catalyst. Therefore, in this study, bifunctional catalyst supports were developed for one-step esterification-transesterification of waste cooking oil by varying the CeO 2 loading on γ-Al 2 O 3 . The bifunctional supports were then impregnated with 5 wt % Mo and characterized using N 2 adsorption-desorption isotherm to determine the surface area of the catalysts while temperature programmed desorption with NH 3 and CO 2 as adsorbents were used to determine the acidity and basicity of the catalysts. Results show that the γ-Al 2 O 3 -CeO 2 supported Mo catalysts are active for the one-step esterification-transesterification of waste cooking oil to produce bio diesel with the Mo/ γ-Al 2 O 3 -20 wt% CeO 2 as the most active catalyst. Optimization of process parameters for the production of bio diesel from waste cooking oil in the presence of this catalyst show that 81.1 % bio diesel yield was produced at 110 degree Celsius with catalyst loading of 7 wt %, agitation speed of 600 rpm, methanol to oil ratio of 30:1 and reaction period of 270 minutes. (author)

Morphology controlled synthesis of monodisperse cobalt hydroxide for supercapacitor with high performance and long cycle life

Science.gov (United States)

Tang, Yongfu; Liu, Yanyan; Yu, Shengxue; Mu, Shichun; Xiao, Shaohua; Zhao, Yufeng; Gao, Faming

2014-06-01

A facile hydrothermal process with hexadecyltrimethyl ammonium bromide (CTAB) as the soft template is proposed to tune the morphology and size of cobalt hydroxide (Co(OH)2). Monodisperse β-phase Co(OH)2 nanowires with uniform size are obtained by controlling the CTAB content and the reaction time. Due to the uniform well-defined morphology and stable structure, the Co(OH)2 nanowires material exhibits high capacitive performance and long cycle life. The specific capacitance of the Co(OH)2 nanowires electrode is 358 F g-1 at 0.5 A g-1, and even 325 F g-1 at 10 A g-1. The specific capacitance retention is 86.3% after 5000 charge-discharge cycles at 2 A g-1. Moreover, the asymmetric supercapacitor is assembled with Co(OH)2 nanowires and nitrite acid treated activated carbon (NTAC), which shows an energy density of 13.6 Wh kg-1 at the power density of 153 W kg-1 under a high voltage of 1.6 V, and 13.1 Wh kg-1 even at the power density of 1.88 kW kg-1.

Carbonate hydrates of the heavy alkali metals: preparation and structure of Rb{sub 2}CO{sub 3} . 1.5 H{sub 2}O und Cs{sub 2}CO{sub 3} . 3 H{sub 2}O; Carbonat-Hydrate der schweren Alkalimetalle: Darstellung und Struktur von Rb{sub 2}CO{sub 3} . 1,5 H{sub 2}O und Cs{sub 2}CO{sub 3} . 3 H{sub 2}O

Energy Technology Data Exchange (ETDEWEB)

Cirpus, V.; Wittrock, J.; Adam, A. [Koeln Univ. (Germany). Inst. fuer Anorganische Chemie

2001-03-01

Rb{sub 2}CO{sub 3} . 1.5 H{sub 2}O and Cs{sub 2}CO{sub 3} . 3 H{sub 2}O were prepared from aqueous solution and by means of the reaction of dialkylcarbonates with RbOH and CsOH resp. in hydrous alcoholes. Based on four-circle diffractometer data, the crystal structures were determined (Rb{sub 2}CO{sub 3} . 1.5 H{sub 2}O: C2/c (no. 15), Z = 8, a = 1237.7(2) pm, b = 1385.94(7) pm, c = 747.7(4) pm, {beta} = 120.133(8) , V{sub EZ} = 1109.3(6) . 10{sup 6} pm{sup 3}; Cs{sub 2}CO{sub 3} . 3 H{sub 2}O: P2/c (no. 13), Z = 2, a = 654.5(2) pm, b = 679.06(6) pm, c = 886.4(2) pm, {beta} = 90.708(14) , V{sub EZ} = 393.9(2) . 10{sup 6} pm{sup 3}). Rb{sub 2}CO{sub 3} . 1.5 H{sub 2}O is isostructural with K{sub 2}CO{sub 3} . 1.5 H{sub 2}O. In case of Cs{sub 2}CO{sub 3} . 3 H{sub 2}O no comparable structure is known. Both structures show {sub {infinity}}{sup 1}[(CO{sub 3}{sup 2-})(H{sub 2}O)]-chains, being connected via additional H{sub 2}O forming columns (Rb{sub 2}CO{sub 3} . 1.5 H{sub 2}O) and layers (Cs{sub 2}CO{sub 3} . 3 H{sub 2}O), respectively. (orig.)

Comparison of Growth and the Cytokines Induced by Pathogenic Yersinia enterocolitica Bio-Serotypes 3/O: 3 and 2/O: 9.

Science.gov (United States)

Yang, Haoshu; Gu, Wenpeng; Qiu, Haiyan; Sun, Guixiang; Liang, Junrong; Li, Kewei; Xiao, Yuchun; Duan, Ran; Jing, Huaiqi; Wang, Xin

2017-01-01

Pathogenic Yersinia enterocolitica is widely distributed in China where the primary bio-serotypes are 3/O: 3 and 2/O: 9. Recently, the distribution of 2/O: 9 strains are being gradually replaced by 3/O: 3 strains where presently 3/O: 3 strains are the major pathogenic Y. enterocolitica in China. To identify the growth conditions and cytokines induced by Y. enterocolitica and providing some clues for this shift, we performed competitive growth in vitro and in vivo for these two bio-serotype strains; and we also compared the cytokines induced by them in infected BALB/C mice. We found 2/O: 9 strains grew more in vitro , while 3/O: 3 strains grew more in vivo regardless of using single cultures or mixed cultures. The cytokines induced by the two strains were similar: interleukin-6 (IL-6), IL-9, IL-13, granulocyte colony-stimulating factor (G-CSF), chemokines (KC), monocyte chemotactic protein 1 (MCP-1), macrophage inflammation protein-1α (MIP-1α), tumor necrosis factor-α (TNF-α), and RANTES were statistically up-regulated upon activation of normal T cells compared to the control. The cytokine values were higher in mixed infections than in single infections except for IL-6, G-CSF, and KC. The data illustrated the different growth of pathogenic Y. enterocolitica bio-serotype 3/O: 3 and 2/O: 9 in vitro and in vivo , and the cytokine changes induced by the two strains in infected BALB/C mice. The growth comparisons of two strains maybe reflect the higher pathogenic ability or resistance to host immune response for Y. enterocolitica bio-serotype 3/O: 3 and maybe it as one of the reason for bacteria shift.

Comparison of Growth and the Cytokines Induced by Pathogenic Yersinia enterocolitica Bio-Serotypes 3/O: 3 and 2/O: 9

Directory of Open Access Journals (Sweden)

Haoshu Yang

2017-05-01

Full Text Available Pathogenic Yersinia enterocolitica is widely distributed in China where the primary bio-serotypes are 3/O: 3 and 2/O: 9. Recently, the distribution of 2/O: 9 strains are being gradually replaced by 3/O: 3 strains where presently 3/O: 3 strains are the major pathogenic Y. enterocolitica in China. To identify the growth conditions and cytokines induced by Y. enterocolitica and providing some clues for this shift, we performed competitive growth in vitro and in vivo for these two bio-serotype strains; and we also compared the cytokines induced by them in infected BALB/C mice. We found 2/O: 9 strains grew more in vitro, while 3/O: 3 strains grew more in vivo regardless of using single cultures or mixed cultures. The cytokines induced by the two strains were similar: interleukin-6 (IL-6, IL-9, IL-13, granulocyte colony-stimulating factor (G-CSF, chemokines (KC, monocyte chemotactic protein 1 (MCP-1, macrophage inflammation protein-1α (MIP-1α, tumor necrosis factor-α (TNF-α, and RANTES were statistically up-regulated upon activation of normal T cells compared to the control. The cytokine values were higher in mixed infections than in single infections except for IL-6, G-CSF, and KC. The data illustrated the different growth of pathogenic Y. enterocolitica bio-serotype 3/O: 3 and 2/O: 9 in vitro and in vivo, and the cytokine changes induced by the two strains in infected BALB/C mice. The growth comparisons of two strains maybe reflect the higher pathogenic ability or resistance to host immune response for Y. enterocolitica bio-serotype 3/O: 3 and maybe it as one of the reason for bacteria shift.

Evolution of controllable urchin-like SrCO{sub 3} with enhanced electrochemical performance via an alternative processing

Energy Technology Data Exchange (ETDEWEB)

Wang, Zhiwei, E-mail: wangzw0818@163.com; He, Geping, E-mail: hgping2013@126.com; Yin, Hongfeng; Bai, Wenyu; Ding, Donghai

2017-07-31

Graphical abstract: Strontium carbonate (SrCO{sub 3}) owning an urchin-like morphology with a hierarchical nanostructure was synthesized. Specific capacitance of SrCO{sub 3} was enhanced greatly by controllable urchin-like morphology through a mechanism of oxygen diffusion. - Highlights: • Urchin-like SrCO{sub 3} hierarchical nanostructure was prepared by hydrothermal route. • Morphology evolution of urchin-like SrCO{sub 3} with different preparation conditions. • Mechanism of nuclear aggregates—nanorods embellishment—urchin-like. • Specific capacitance of SrCO{sub 3} was enhanced greatly by controllable urchin-like morphology. - Abstract: Strontium carbonate (SrCO{sub 3}) owning an urchin-like morphology with a hierarchical nanostructure was synthesized by the reactants of strontium nitrate and urea via a facilitative, green initiative hydrothermal route. Samples characterization results of the structure showed that the surface of urchin-like SrCO{sub 3} was evenly distributed with nanorods with a diameter of about 50 nm and lengths of 1–2 μm. It was also found that the hydrothermal reaction time and reactants of trace concentrations changes will have an impact on the size and morphology. For these reasons we presented the crystal growth mechanism of “nuclear aggregates–nanorods embellishment–urchin-like” during the process of fabricating urchin-like SrCO{sub 3} crystal. Specific capacitance was enhanced more than 6 times, which dug out the optimal urchin-like SrCO{sub 3} influenced by a growth of surface nanorods.

Vacuum ultraviolet excited photoluminescence properties of Gd2O2CO3:Eu3+ phosphor

Institute of Scientific and Technical Information of China (English)

WANG Zhilong; WANG Yuhua; ZHANG Jiachi

2008-01-01

The Gd2O2CO3:Eu3+ with type-II structure phosphor was successfully synthesized via flux method at 400℃ and their photoluminescence properties in vacuum ultraviolet (VUV) region were examined. The broad and strong excitation bands in the range of 153-205 nm owing to the CO32- host absorption and charge transfer (CT) of Gd3+-O2- were observed for Gd2O2CO3:Eu3+. Under 172 nm excitation, Gd2O2CO3:Eu3+ exhibited strong red emission with good color purity, indicating Eu3+ ions located at low symmetry sites and the chromaticity coordination of luminescence for Gd2O2CO3:Eu3+ was (x=0.652, y=0.345). The photoluminescence quenching concentration of Eu3+ excited by 172 nm for Gd2O2CO3:Eu3+ was about 5%. Gd2O2CO3:Eu3+ would be a potential VUV-excited red phosphor applied in mercury-free fluorescent lamps.

Architecture of 3D ZnCo{sub 2}O{sub 4} marigold flowers: Influence of annealing on cold emission and photocatalytic behavior

Energy Technology Data Exchange (ETDEWEB)

Kokane, Sanjay B.; Suryawanshi, Sachin R. [Center for Advanced Studies in Material Science and Condensed Matter Physics, Department of Physics, Savitribai Phule Pune University, Pune 411007 (India); Sasikala, R., E-mail: sasikala@barc.gov.in [Chemistry Division, Bhabha Atomic Research Centre, Mumbai 411085 (India); More, Mahendra A., E-mail: mam@physics.unipune.ac.in [Center for Advanced Studies in Material Science and Condensed Matter Physics, Department of Physics, Savitribai Phule Pune University, Pune 411007 (India); Sartale, Shrikrishna D., E-mail: sdsartale@physics.unipune.ac.in [Center for Advanced Studies in Material Science and Condensed Matter Physics, Department of Physics, Savitribai Phule Pune University, Pune 411007 (India)

2017-06-15

The present work demonstrates the field emission characteristics and photocatalytic behavior of ZnCo{sub 2}O{sub 4} marigold flowers synthesized via a facile hydrothermal method. The effect of annealing of these 3D porous hierarchical nanostructures on field emission and photocatalytic performances is studied. When compared with the as-synthesized sample, annealed ZnCo{sub 2}O{sub 4} exhibits a ∼2-fold improvement in photocatalytic activity for methylene blue (MB) degradation under visible light irradiation. The turn-on, threshold fields and high emission current densities are also strongly influenced as a result of annealing. The turn on field required to draw an emission current density of ∼1 μA/cm{sup 2} is found to be ∼2.4 and ∼1.8 V/μm for as-synthesized and annealed ZnCo{sub 2}O{sub 4} marigold flowers, respectively. Field-emission measurements demonstrate remarkably large field enhancement and better stability for annealed samples. The X-ray diffraction and Raman analysis reveal that annealing improves the crystallinity and also help to remove the structural defects in ZnCo{sub 2}O{sub 4}. The enhancement in the field emission and photocatalytic activity of annealed ZnCo{sub 2}O{sub 4} marigold flowers is attributed to the modification of electronic properties as a result of dehydration, crystallite growth and reduced surface defects/impurity phases. - Highlights: • 3D hierarchical porous ZnCo{sub 2}O{sub 4} marigold flowers synthesis by hydrothermal method. • Roles of CTAB as capping agent and thermal annealing are investigated. • Thermal annealing improves photocatalysis and field emission behavior drastically.

Iridium Clusters Encapsulated in Carbon Nanospheres as Nanocatalysts for Methylation of (Bio)Alcohols.

Science.gov (United States)

Liu, Qiang; Xu, Guoqiang; Wang, Zhendong; Liu, Xiaoran; Wang, Xicheng; Dong, Linlin; Mu, Xindong; Liu, Huizhou

2017-12-08

C-H methylation is an attractive chemical transformation for C-C bonds construction in organic chemistry, yet efficient methylation of readily available (bio)alcohols in water using methanol as sustainable C1 feedstock is limited. Herein, iridium nanocatalysts encapsulated in yolk-shell-structured mesoporous carbon nanospheres (Ir@YSMCNs) were synthesized for this transformation. Monodispersed Ir clusters (ca. 1.0 nm) were encapsulated in situ and spatially isolated within YSMCNs by a silica-assisted sol-gel emulsion strategy. A selection of (bio)alcohols (19 examples) was selectively methylated in aqueous phase with good-to-high yields over the developed Ir@YSMCNs. The improved catalytic efficiencies in terms of activity and selectivity together with the good stability and recyclability were contributable to the ultrasmall Ir clusters with oxidation chemical state as a consequence of the confinement effect of YSMCNs with interconnected nanostructures. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

First identification and thermodynamic characterization of the ternary U(VI) species, UO2(O2)(CO3)2(4-), in UO2-H2O2-K2CO3 solutions.

Science.gov (United States)

Goff, George S; Brodnax, Lia F; Cisneros, Michael R; Peper, Shane M; Field, Stephanie E; Scott, Brian L; Runde, Wolfgang H

2008-03-17

In alkaline carbonate solutions, hydrogen peroxide can selectively replace one of the carbonate ligands in UO2(CO3)3(4-) to form the ternary mixed U(VI) peroxo-carbonato species UO2(O2)(CO3)2(4-). Orange rectangular plates of K4[UO2(CO3)2(O2)].H2O were isolated and characterized by single crystal X-ray diffraction studies. Crystallographic data: monoclinic, space group P2(1)/ n, a = 6.9670(14) A, b = 9.2158(10) A, c = 18.052(4) A, Z = 4. Spectrophotometric titrations with H 2O 2 were performed in 0.5 M K 2CO 3, with UO2(O2)(CO3)2(4-) concentrations ranging from 0.1 to 0.55 mM. The molar absorptivities (M(-1) cm(-1)) for UO2(CO3)3(4-) and UO2(O2)(CO3)2(4-) were determined to be 23.3 +/- 0.3 at 448.5 nm and 1022.7 +/- 19.0 at 347.5 nm, respectively. Stoichiometric analyses coupled with spectroscopic comparisons between solution and solid state indicate that the stable solution species is UO2(O2)(CO3)2(4-), which has an apparent formation constant of log K' = 4.70 +/- 0.02 relative to the tris-carbonato complex.

A novel 3D structure composed of strings of hierarchical TiO{sub 2} spheres formed on TiO{sub 2} nanobelts with high photocatalytic properties

Energy Technology Data Exchange (ETDEWEB)

Jiang, Yongjian [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, School of Renewable Energy, North China Electric Power University, Beijing 102206 (China); Li, Meicheng, E-mail: mcli@ncepu.edu.cn [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, School of Renewable Energy, North China Electric Power University, Beijing 102206 (China); Suzhou Institute, North China Electric Power University, Suzhou 215123 (China); Song, Dandan; Li, Xiaodan; Yu, Yue [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, School of Renewable Energy, North China Electric Power University, Beijing 102206 (China)

2014-03-15

A novel hierarchical titanium dioxide (TiO{sub 2}) composite nanostructure with strings of anatase TiO{sub 2} hierarchical micro-spheres and rutile nanobelts framework (TiO{sub 2} HSN) is successfully synthesized via a one-step hydrothermal method. Particularly, the strings of hierarchical spheres are assembled by very thin TiO{sub 2} nanosheets, which are composed of highly crystallized anatase nanocrystals. Meanwhile, the HSN has a large surface area of 191 m{sup 2}/g, which is about 3 times larger than Degussa P25. More importantly, the photocatalytic activity of HSN and P25 were evaluated by the photocatalytic oxidation decomposition of methyl orange (MO) under UV light illumination, and the TiO{sub 2} HSN shows enhanced photocatalytic activity compared with Degussa P25, as result of its continuous hierarchical structures, special conductive channel and large specific surface area. With these features, the hierarchical TiO{sub 2} may have more potential applications in the fields of dye-sensitized solar cells and lithium ion batteries. -- Graphical abstract: Novel TiO{sub 2} with anatase micro-spheres and rutile nanobelts is synthesized. Enhanced photocatalysis is attributed to hierarchical structures (3D spheres), conductive channel (1D nanobelts) and large specific surface area (2D nanosheet). Highlights: • The novel TiO{sub 2} nanostructure (HSN) is fabricated for the first time. • HSN is composed of strings of anatase hierarchical spheres and rutile nanobelt. • HSN presents a larger S{sub BET} of 191 m{sup 2}/g, 3 times larger than the Degussa P25 (59 m{sup 2}/g). • HSN owns three kinds of dimensional TiO{sub 2} (1D, 2D and 3D) simultaneously. • HSN exhibits better photocatalytic performance compared with Degussa P25.

Hierarchical Layered WS2 /Graphene-Modified CdS Nanorods for Efficient Photocatalytic Hydrogen Evolution.

Science.gov (United States)

Xiang, Quanjun; Cheng, Feiyue; Lang, Di

2016-05-10

Graphene-based ternary composite photocatalysts with genuine heterostructure constituents have attracted extensive attention in photocatalytic hydrogen evolution. Here we report a new graphene-based ternary composite consisting of CdS nanorods grown on hierarchical layered WS2 /graphene hybrid (WG) as a high-performance photocatalyst for hydrogen evolution under visible light irradiation. The optimal content of layered WG as a co-catalyst in the ternary CdS/WS2 /graphene composites was found to be 4.2 wt %, giving a visible light photocatalytic H2 -production rate of 1842 μmol h(-1)  g(-1) with an apparent quantum efficiency of 21.2 % at 420 nm. This high photocatalytic H2 -production activity is due to the deposition of CdS nanorods on layered WS2 /graphene sheets, which can efficiently suppress charge recombination, improve interfacial charge transfer, and provide reduction active sites. The proposed mechanism for the enhanced photocatalytic activity of CdS nanorods modified with hierarchical layered WG was further confirmed by transient photocurrent response. This work shows that a noble-metal-free hierarchical layered WS2 /graphene nanosheets hybrid can be used as an effective co-catalyst for photocatalytic water splitting. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of Bio-Based Poly(lactic acid-co-10-hydroxy decanoate Copolymers with High Thermal Stability and Ductility

Directory of Open Access Journals (Sweden)

Dongjian Shi

2015-03-01

Full Text Available Novel bio-based aliphatic copolyesters, poly(lactic acid-co-10-hydroxy decanoate (P(LA-co-HDA, PLH, were successfully synthesized from lactic acid (LA and 10-hydroxycapric acid (HDA by a thermal polycondensation process, in the presence of p-toluenesulfonic acid (p-TSA and SnCl2·2H2O as co-catalyst. The copolymer structure was characterized by Fourier transform infrared (FTIR and proton nuclear magnetic resonance (1H NMR. The weight average molecular weights (Mw of PLH, from gel permeation chromatography (GPC measurements, were controlled from 18,500 to 37,900 by changing the molar ratios of LA and HDA. Thermogravimetric analysis (TGA results showed that PLH had excellent thermal stability, and the decomposition temperature at the maximum rate was above 280 °C. The glass transition temperature (Tg and melting temperature (Tm of PLH decreased continuously with increasing the HDA composition by differential scanning calorimetry (DSC measurements. PLH showed high ductility, and the breaking elongation increased significantly by the increment of the HDA composition. Moreover, the PLH copolymer could degrade in buffer solution. The cell adhesion results showed that PLH had good biocompatibility with NIH/3T3 cells. The bio-based PLH copolymers have potential applications as thermoplastics, elastomers or impact modifiers in the biomedical, industrial and agricultural fields.

Assembly of tin oxide/graphene nanosheets into 3D hierarchical frameworks for high-performance lithium storage.

Science.gov (United States)

Huang, Yanshan; Wu, Dongqing; Han, Sheng; Li, Shuang; Xiao, Li; Zhang, Fan; Feng, Xinliang

2013-08-01

3D hierarchical tin oxide/graphene frameworks (SnO2 /GFs) were built up by the in situ synthesis of 2D SnO2 /graphene nanosheets followed by hydrothermal assembly. These SnO2 /GFs exhibited a 3D hierarchical porous architecture with mesopores (≈3 nm), macropores (3-6 μm), and a large surface area (244 m(2) g(-1) ), which not only effectively prevented the agglomeration of SnO2 nanoparticles, but also facilitated fast ion and electron transport in 3D pathways. As a consequence, the SnO2 /GFs exhibited a high capacity of 830 mAh g(-1) for up to 70 charge-discharge cycles at 100 mA g(-1) . Even at a high current density of 500 mA g(-1) , a reversible capacity of 621 mAh g(-1) could be maintained for SnO2 /GFs with excellent cycling stability. Such performance is superior to that of previously reported SnO2 /graphene and other SnO2 /carbon composites with similar weight contents of SnO2 . Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hierarchical Ni-Co layered double hydroxide nanosheets on functionalized 3D-RGO films for high energy density asymmetric supercapacitor

Science.gov (United States)

Jiang, Liyang; Sui, Yanwei; Qi, Jiqiu; Chang, Yuan; He, Yezeng; Meng, Qingkun; Wei, Fuxiang; Sun, Zhi; Jin, Yunxue

2017-12-01

In this paper, ultrathin reduced graphene oxide films on nickel foam were fabricated via a facile dip-coating method combined with thermal reduction. Hierarchical Ni-Co layered double hydroxide nanosheets with network structure were electrodeposited on the ultrathin reduced graphene oxide films in a simple three-electrode system. The thickness of Ni-Co layered double hydroxide nanosheets can be controlled through adjusting the deposition temperature. The as-prepared electrode exhibited excellent electrochemical performance with specific capacitance of 1454.2 F g-1 at a current density of 1 A g-1. An asymmetric supercapacitor device was designed with the as-prepared composites as positive electrode material and Nitrogen-doped reduced graphene oxide as negative electrode material. This device could be operated in a working voltage range of 0-1.8 V in 1 M KOH aqueous electrolyte, delivering a high energy density of 56.4 W h kg-1 at a power density of 882.5 W kg-1. One supercapacitor can power two LEDs with rated voltage of 1.8-2.0 V. After 10,000 consecutive charge-discharge tests at 10 A g-1, this asymmetric supercapacitor revealed an excellent cycle life with 98.3% specific capacitance retention. These excellent electrochemical performances make it become one of most promising candidates for high energy supercapacitor device.

Ce2Co3Ge5: a new U2Co3Si5 - type valance fluctuating compound

International Nuclear Information System (INIS)

Layek, Samar; Hossain, Zakir

2010-01-01

Poly crystalline sample of Ce 2 Co 3 Ge 5 have been prepared by arc melting and consequently annealing at 1100 deg C. Rietveld refinement of XRD shows that it crystallize in the orthorhombic U 2 Co 3 Si 5 structure (space group Ibam) with crystal parameters a= 9.802A, b= 11.777A and c= 5.941A and unit cell volume V= 684.8 A 3 The unit cell volume of Ce 2 Co 3 Ge 5 is seen clearly to deviate from that expected on the basis of lanthanide contraction. From susceptibility measurement, effective magnetic moment of this compound μ eff = 0.95 μ B which is lower than magnetic moment free for Ce 3+ ions (2.54 μB) but higher than that of non-magnetic Ce 4+ state (0 μ B ). All these results clearly indicated Ce 2 Co 3 Ge 5 to be a mixed valance compound. (author)

Thermoelectric properties of Ba3Co2O6(CO3)0.7 containing one-dimensional CoO6 octahedral columns

OpenAIRE

Iwasaki, Kouta; Yamamoto, Teruhisa; Yamane, Hisanori; Takeda, Takashi; Arai, Shigeo; Miyazaki, Hidetoshi; Tatsumi, Kazuyoshi; Yoshino, Masahito; Ito, Tsuyoshi; Arita, Yuji; Muto, Shunsuke; Nagasaki, Takanori; Matsui, Tsuneo

2009-01-01

The thermoelectric properties of Ba3Co2O6(CO3)0.7 have been investigated using prismatic single crystals elongated along the c axis. Ba3Co2O6(CO3)0.7 has a pseudo-one-dimensional structure similar to that of 2H perovskite-type BaCoO3 and contains CoO6 octahedral columns running parallel to the c axis. The prismatic crystals are grown by a flux method using a K2CO3–BaCl2 flux. The electrical conductivity(σ) along the columns (c axis) exhibits a metallic behavior (670–320 S cm−1 in the temperat...

Bio politics - The bio-environment - bio-culture of the Danube

International Nuclear Information System (INIS)

Vlavianos-Arvanitis, A.

1997-01-01

The bio-environment has been the single most important correlation in human history and can successfully promote international co-operational co-operation and understanding. With the construction of a network for collaboration, the 'Danube Countries' can come together in celebration of their culture and heritage. As the Danube flows from the Black Forest to the Black Sea, it carries messages of peace, hope and co-operation. Applying these messages to every endeavour can improve our quality of life and lead to a brighter future. Since its inception in 1985, the Bio politics International Organization (B.I.O.) has been labouring to raise awareness of the urgent need to instate a new system of norms and principles, compatible with sound environmental management and with the most important task of ensuring global literacy on environmental issues. Along with critically re-assessing the concept of profit, the goal is to adopt a system of bio centric values, where respect for the bio-environment will govern our every action and thought

Microorganisms implication in the CO2 geologic storage processes

International Nuclear Information System (INIS)

Dupraz, S.

2008-01-01

A first result of this thesis is the building and validation of a circulation reactor named BCC (Bio-mineralization Control Cell). The reactor has the functionality of a biological reactor and allows a monitoring of physico-chemical characteristics such as Eh, pH, electrical conductivity, spectro-photochemical parameters. It also has a capability of percolation through rock cores. It is a first step toward an analogical modeling of interactions between injected CO 2 and deep bio-spheric components. Moreover, a new spectro-photochemical method for monitoring reduced sulfur species has been developed which allows efficient monitoring of sulfate-reducing metabolisms. In the thesis, we have tested four metabolisms relevant to bio-mineralisation or biological assimilation of CO 2 : a reference ureolytic aerobic strain, Bacillus pasteurii, a sulfate-reducing bacterium, Desulfovibrio longus, a sulfate-reducing consortium (DVcons) and an homoacetogenic bacterium, Acetobacterium carbinolicum. In the case of Bacillus pasteurii, which is considered as a model for non photosynthetic prokaryotic carbonate bio-mineralization, we have demonstrated that the biological basification and carbonate bio-mineralization processes can be modelled accurately both analogically and numerically under conditions relevant to deep CO 2 storage, using a synthetic saline groundwater. We have shown that salinity has a positive effect on CO 2 mineral trapping by this bacterium; we have measured the limits of the system in terms of CO 2 pressure and we have shown that the carbonates that nucleate on intracellular calcium phosphates have specific carbon isotope signatures. The studied deep-subsurface strains (Desulfovibrio longus and Acetobacterium carbinolicum) as well as the sulfate-reducing consortium also have capabilities of converting CO 2 into solid carbonates, much less efficient though than in the case of Bacillus pasteurii. However, once inoculated in synthetic saline groundwater and