Radiation monitoring network of the Czech Republic

International Nuclear Information System (INIS)

Kuca, P.; Novak, L.; Rulik, P.; Tecl, J.

2003-01-01

The Radiation Monitoring Network (RMN) of the Czech Republic was established after the Chernobyl accident in 1986 and it is developed all the time. It is co-ordinated by the State Office for Nuclear Safety in co-operation with the National Radiation Protection Institute. Czech RMN consists of the several sub-networks, which include selected or all permanent parts of RMN. The sub-networks are following: the Early Warning Network (EWN), the TLD Territorial Network, the Network of the Measuring Sites of Air Contamination, the Network of Laboratories Equipped with Gamma-spectrometric and Radiochemical Analytical Instrumentation, the Ground and Airborne Mobile Groups. The Laboratory of Monitoring of Internal Contamination and the information system (IS) are a significant part of RMN, too. The data of RMN resulting from monitoring are transferred to the central database of CRMN, processed by the information system (IS). They are used in normal and emergency situations for an evaluation of radiation situation and for preparation of recommendations for protection of the public and the environment. In 2002 any extraordinary radioactivity in the environment was not detected and also none of the measuring points recorded any exceeding of established investigation levels. In components of environment and also in human beings a very low activity of 137 Cs was still measurable, that had been released into environment after the Chernobyl accident and by the nuclear weapon tests in sixties of the last century. (authors)

SWFSC/MMTD/ETP: Monitoring of Porpoise Stocks (MOPS) 1986-1990

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — In 1986 the U.S. National Marine Fisheries Service (NMFS) initiated a long-term, large-scale research program to monitor trends in the abundance of dolphin...

Radiological effluent and onsite area monitoring report for the Nevada Test Site (January 1986-December 1986)

International Nuclear Information System (INIS)

Gonzalez, D.A.

1987-09-01

This report documents the environmental surveillance program at the Nevada Test Site as conducted by the Department of Energy (DOE) onsite radiological safety contractor from January 1986 through December 1986. It presents results and evaluations of radioactivity measurements in air and water, and of direct gamma radiation exposure rates. It establishes relevant correlations between the data recorded and DOE concentration guides (CG's). External gamma exposure levels and radioactivity in air and water on the Nevada Test Site were low compared to DOE guidelines. The highest average gross beta concentration in air was 0.005% of the DOE concentration guide (CG). The highest average Pu-239 concentration was 7.7% of the standard. The highest average tritium concentration was 0.39% of the standard. Kr-85 concentrations increased slightly from CY-1985 to CY-1986. Xe-133 remained nondetectable with some exceptions. The highest average gross beta concentration in potable water remained within the applicable standard for drinking water. The highest average Pu-239 concentration from contaminated waters was 0.0005% of the concentration guide. The highest average tritium concentration in noncontaminated water was 6% of the level for drinking water required by the National Interim Primary Drinking Water Regulation. The amounts of tritium-bearing effluent released to contaminated waste ponds was calculated and reported to DOE Headquarters. Gamma radiation measurements were roughly the same in CY-1986 relative to the previous year. All surveillance results from the Radioactive Waste Management Site (RWMS) indicate that no detectable releases of radioactive materials occurred in that network in 1986. 29 refs., 14 figs., 23 tabs

Environmental monitoring for radioactivity in Scotland: 1981 to 1985

Energy Technology Data Exchange (ETDEWEB)

Anon.

1987-01-01

A bulletin, prepared by Her Majesty's Industrial Pollution Inspectorate (HMIPI) of the Scottish Development Department (SDD), contains a summary of the environmental monitoring for radioactivity carried out in Scotland as part of the statutory procedure for ensuring the safety of radioactive waste disposals from nuclear facilities. The monitoring results for discharges to both the atmosphere and the sea over the period 1981 to 1985 are presented for BNFL's Chapelcross and Sellafield Works, UKAEA Dounreay Nuclear Power Development Establishment, SSEB Hunterston Power Station and MOD Naval Installations. It is concluded that public radiation exposure in Scotland from environmental radioactivity arising from radioactive waste disposal has been well within the internationally recommended limits.

The monitoring network for radioactivity in air in Norway. Annual report 2000; Nettverket for overvaaking av radioaktivitet i luft i Norge

Energy Technology Data Exchange (ETDEWEB)

Berg, Thor Chr.

2002-06-01

On the instruction of the Radiation Monitoring Authority (SSV), NILU has assumed responsibility for the operation of a monitoring network for radioactivity. This report describes this network. None of the 29 stations of the network detected radiation in 2000 that cannot be attributed to the natural variation of the radiation levels or to normal technical irregularities. However, much of the equipment was acquired in the years following the Chernobyl accident of 1986 and is in need of replacement.

South Pacific Nuclear Free Zone Treaty Act 1986 - No. 140 of 1986

International Nuclear Information System (INIS)

1986-01-01

The purpose of this Act is to give effect to Australia's obligations as a Party to the South Pacific Nuclear Free Zone Treaty of 6 August 1985. The Act is supplemented by the provisions of the Environment Protection (Sea Dumping) Act 1981 as amended in 1986 as regards dumping of radioactive material into the sea. The Act repeats the substantive provisions of the Treaty and lays down prohibitions in relation to nuclear explosive devices. (NEA) [fr

1986 environmental monitoring report

International Nuclear Information System (INIS)

Miltenberger, R.P.; Royce, B.A.; Naidu, J.R.

1987-06-01

The environmental levels of radioactivity and other pollutants found in the vicinity of BNL during 1986 are summarized in this report. The environmental data include external radiation levels; radioactive air particulates and halogens; tritium concentrations; the amounts and concentrations of radioactivity in and the water quality of the stream into which liquid effluents are released; the organics, radioactivity, and water quality of the potable supply wells; the concentrations of radioactivity in biota from the stream; and the concentrations of organics, radioactivity, and the water quality of ground waters underlying the Laboratory. In 1986, the results of the surveillance program demonstrated that the Laboratory has operated within the applicable environmental standards

The uranium market: 1986-2000

International Nuclear Information System (INIS)

Lewiner, C.; Walton, D.; Sinclair-Smith, D.

1987-01-01

This paper summarizes the main conclusions of the 1986 supply and demand report of the Uranium Institute. The probable nuclear generating capacity is estimated for 1986-2000. Previous capacity forecasts (1981-1986) are compared with actual generating capacity. When looking at demand, a distinction has to be made between what reactor operators require to fuel reactors (reactor requirements) and what they intend to purchase (uranium procurements). This distinction is defined and discussed. The interaction between supply and demand is shown and factors affecting trade (eg government policies) are discussed. 1985 was the first year when uranium production was less than reactor requirements. This shortfall will continue for a number of years with the current excess in consumer inventories supplying the difference between reactor requirements and uranium procurements. Uranium demand should exceed production by 1988 but additional capacity should be available from planned and possible restart and possible new facilities. (U.K.)

Interim environmental monitoring report for the Nevada test site, first quarter 1981

International Nuclear Information System (INIS)

1981-08-01

During the first calendar quarter of 1981, no radioactivity from the nuclear tests conducted at the Nevada Test Site was measured offsite by the US Environmental Protection Agency's Environmental Monitoring Systems Laboratory. Low concentrations of 95 Zr, 95 Nb, 103 Ru, and 141 Ce attributed to the People's Republic of China nuclear test of October 15, 1980, were detected in air samples throughout the Air Surveillance Network. The maximum concentrations of these radionuclides were less than 0.1 percent of the Concentration Guides. The dosimeters of fixed station at Complex I (Coal Valley) indicated an exposure of 1.6 mR, and the dosimeters of two offsite residents, one living at Glendale, Nev., and the other near Complex I, (Coal Valley) appeared to have net exposures of 3.1 mR and 3.2 mR, respectively; however, further evaluation revealed that the net exposures were not due to an exposure from NTS operations, but may be a statistical anomaly related to an unusually low variation in the environmental background exposure rate. Further investigation is in progress

Ocean breeze monitoring network at the Oyster Creek Nuclear Plant

International Nuclear Information System (INIS)

Heck, W.

1987-01-01

The Oyster Creek Nuclear Generating Station (OCNGS) is located in New Jersey 10 km west of the Atlantic Ocean. Routine meteorological monitoring at the station has consisted of a single meteorological tower 120 m high and instrumented at the 10-m, 46-m, and 116-m levels. An analysis of 5 yr of data from this tower showed the OCNGS is affected by an ocean breeze ∼ 1 day out of 4 during May through August. This suggested the need for meteorological monitoring in addition to the single met tower at OCNGS. As a result of the 1985 OCNGS meteorological monitoring study, GPU Nuclear established an ocean breeze monitoring network in the fall of 1986. It is a permanent part of OCNGS meteorological monitoring and consists of the same sites as used in the 1985 field study. Meteorological towers are located at the ocean site, the inland site, and at OCNGS. The ocean tower is 13 m (43 ft) high, the inland tower 10 m (33 ft), and the OCNGS tower 116 m (380 ft). Wind speed, wind direction, and temperature are measured on each tower; delta-temperature is also measured on the main tower. The instruments are calibrated in the spring, summer, and fall. The network is operated and maintained by GPU Nuclear Environmental Controls. The ocean breeze monitoring network and meteorological information system forms the basis for including the effects of the ocean breeze in OCNGS emergency off-site dose assessment

Environmental monitoring at the Lawrence Livermore National Laboratory: 1986 annual report

International Nuclear Information System (INIS)

Holland, R.C.; Buddemeier, R.W.; Brekke, D.D.

1987-04-01

This report documents the results of the environmental monitoring program at the Lawrence Livermore National Laboratory (LLNL) for 1986. To evaluate the effect of LLNL operations on the local environment, measurements of direct radiation and a variety of radionuclides and chemical pollutants in ambient air, soil, surface water, groundwater, vegetation, milk, foodstuff, and sewage effluents were made at both the Livermore site and nearby Site 300. This report was prepared to meet the requirements of DOE Order 5484.1. Evaluations are made of LLNL's compliance with all applicable guides, standards, and limits for radiological and nonradiological releases to the environment. The data indicate that no releases in excess of the applicable standards were made during 1986, and that LLNL operations had no adverse environmental impact

Slovenian Network of Isotopes in Precipitation (SLONIP) - a review of activities in the period 1981-2015

Science.gov (United States)

Vreča, Polona; Kanduč, Tjaša; Kocman, David; Lojen, Sonja; Štrok, Marko; Robinson, Johanna Amalia

2017-04-01

The importance of collecting data on the water isotope composition of precipitation in the frame of the Global Network of Isotopes in Precipitation (GNIP) has been steadily increasing since it was initiated by the IAEA and the WMO in 1958, particularly in the last decade (Terzer et al., 2013). GNIP provides an important database for water resources management, verifying and improving atmospheric circulation models, studying climates and the interactions between water in the atmosphere and the biosphere, providing baseline information for the authentication of commodities, etc. Geographical diversity of Slovenia influences the climate and also the water cycle considerably, therefore monitoring of isotopes in precipitation is of particular interest. A review on monitoring of isotopes in precipitation was performed and information about sampling, analytical methods, available data and their evaluation was collected for the period 1981-2015. The first regular and systematic monitoring began in 1981 in Ljubljana (Pezdič, 1999). Later, a programme of collecting new data at a higher spatial density and temporal frequency in different parts of the country by different research groups has been initiated and was extended several times. Consequently, the number of sampling locations has grown within Slovenian Network of Isotopes in Precipitation (SLONIP) and altogether isotopes were monitored at more than 30 different locations countrywide (Vreča and Malenšek, 2016). However, the network is still not a part of a national monitoring programme, such as that operating in some European countries, for example, in Switzerland (Schürch et al., 2003). Only part of Slovenian data is available in GNIP database. Based on the collected data, we identified gaps in the research and made recommendations for future monitoring in the frame of the SLONIP. The list of main gaps includes limited information about sampling (e.g. missing coordinates, type of collector, period, frequency

1986 environmental monitoring program report for the Idaho National Engineering Laboratory Site

International Nuclear Information System (INIS)

Hoff, D.L.; Chew, E.W.; Rope, S.K.

1987-05-01

This report presents onsite and offsite data collected in 1986 for the routine environmental monitoring program conducted by the Radiological and Environmental Sciences Laboratory (RESL) of the Department of Energy (DOE) at the Idaho National Engineering Laboratory (INEL) Site. The purpose of this routine program is to monitor radioactive and nonradioactive materials resulting from INEL Site operations which may reach the surrounding offsite environment and population. This report is prepared in accordance with the DOE requirements in draft DOE Order 5484.1 and is not intended to cover the numerous special environmental research programs being conducted at the INEL by RESL and others

Portsmouth Gaseous Diffusion Plant environmental monitoring report for calendar year 1981

International Nuclear Information System (INIS)

Acox, T.A.; Anderson, R.E.; Hary, L.F.; Klein, L.S.; Vausher, A.L.

1982-04-01

At the Portsmouth Gaseous Diffusion Plant all effluent streams are sampled regularly and analyzed to assess compliance with applicable environmental standards. Radioactivity is measured in air, water, food, soil, and sediments; and radiation doses to the public are calculated. All public radiation doses from process effluents are well within Department of Energy and US EPA standards. Non-radioactive effluents either presently comply with federal standards or will comply upon completion of planned projects. The environmental impact of effluents from cleaning and decontamination operations has been reduced through flow reduction and improved chemical treatment. CY-1981 was the first full year under a new National Pollutant Discharge. Elimination System (NPDES) permit for liquid effluents; compliance with the permit's discharge limits did not present any significant problems. Engineering is proceeding on projects to be constructed through 1985 to further reduce the impact of liquid effluents. A new licensed sanitary landfill utilizing the area fill method went into operation in July 1981. Although neither the State of Ohio nor the federal government has established standards for fluoride in the atmosphere or in vegetation, fluorides are monitored because they are used extensively in the gaseous diffusion process

Implementing Monitored Natural Attenuation and Expediting Closure at Fuel-Release Sites

Science.gov (United States)

2004-08-01

gasoline, kerosene, diesel, and jet fuel (e.g., Jamison et al., 1975; Atlas , 1981, 1984, and 1988; Young, 1984; Bartha , 1986; Wilson et al., 1986 and...Supporting data. Gas Research Institute, Chicago, Illinois. Atlas , R. M. 1981. Microbial degradation of petroleum hydrocarbons - an Environmental... Microbial Ecology 12:155-172 Battelle. 1984. Chemical Attenuation Rates Coefficients, and Constants in Leachate Migration. Vol I: Critical Review

Serial Network Flow Monitor

Science.gov (United States)

Robinson, Julie A.; Tate-Brown, Judy M.

2009-01-01

Using a commercial software CD and minimal up-mass, SNFM monitors the Payload local area network (LAN) to analyze and troubleshoot LAN data traffic. Validating LAN traffic models may allow for faster and more reliable computer networks to sustain systems and science on future space missions. Research Summary: This experiment studies the function of the computer network onboard the ISS. On-orbit packet statistics are captured and used to validate ground based medium rate data link models and enhance the way that the local area network (LAN) is monitored. This information will allow monitoring and improvement in the data transfer capabilities of on-orbit computer networks. The Serial Network Flow Monitor (SNFM) experiment attempts to characterize the network equivalent of traffic jams on board ISS. The SNFM team is able to specifically target historical problem areas including the SAMS (Space Acceleration Measurement System) communication issues, data transmissions from the ISS to the ground teams, and multiple users on the network at the same time. By looking at how various users interact with each other on the network, conflicts can be identified and work can begin on solutions. SNFM is comprised of a commercial off the shelf software package that monitors packet traffic through the payload Ethernet LANs (local area networks) on board ISS.

Availability of thermal power plants 1977-1986

International Nuclear Information System (INIS)

Nitsch, D.; Schmitz, H.

1987-01-01

To get a picture of power plant availability and its influencing factors, availability data have been acquired and evaluated by VGB according to different design and operation parameters since 1970. The present volume is the 16th annual statistics since 1970. It covers the decade of 1977 to 1986 and contains availability data of 384 power plants in Germany and abroad, with a total of 94.896 MW and 3.768 plant years. Data are presented on fossil-fuelled units, units with a combined gas/steam cycle, nuclear power plants and gas turbine systems, with further sub-categories according to unit size, fuel, type, years of operation, and operating regime. German plants are reviewed separately. All power data are gross data measured at the generator terminals. For a comparative evaluation, the data of 1986 are supplemented by yearly averages since 1977 and averages for the decade from 1977 to 1986. Since 1978, nonavailability data are categorized as 'unscheduled' and 'scheduled' nonavailabilities. For availability data of 1970 to 1976, see the VGB publication 'Availability of thermal power plants, 1970 to 1981'. (orig./UA) [de

OSCAR experiment high-density network data report: Event 3 - April 16-17, 1981

Energy Technology Data Exchange (ETDEWEB)

Dana, M.T.; Easter, R.C.; Thorp, J.M.

1984-12-01

The OSCAR (Oxidation and Scavenging Characteristics of April Rains) experiment, conducted during April 1981, was a cooperative field investigation of wet removal in cyclonic storm systems. The high-density component of OSCAR was located in northeast Indiana and included sequential precipitation chemistry measurements on a 100 by 100 km network, as well as airborne air chemistry and cloud chemistry measurements, surface air chemistry measurements, and supporting meteorological measurements. Four separate storm events were studied during the experiment. This report summarizes data taken by Pacific Northwest Laboratory (PNL) during the third storm event, April 16-17. The report contains the high-density network precipitation chemistry data, air chemistry and cloud chemistry data from the PNL aircraft, and meteorological data for the event, including standard National Weather Service products and radar and rawindsonde data from the network. 4 references, 76 figures, 6 tables.

OSCAR experiment high-density network data report: Event 1 - April 8-9, 1981

Energy Technology Data Exchange (ETDEWEB)

Dana, M.T.; Easter, R.C.; Thorp, J.M.

1984-12-01

The OSCAR (Oxidation and Scavenging Characteristics of April Rains) experiment, conducted during April 1981, was a cooperative field investigation of wet removal in cyclonic storm systems. The high-densiy component of OSCAR was located in northeast Indiana and included sequential precipitation chemistry measurements on a 100 by 100 km network, as well as airborne air chemistry and cloud chemistry measurements, surface air chemistry measurements, and supporting meteorological measurements. Four separate storm events were studied during the experiment. This report summarizes data taken by Pacific Northwest Laboratory (PNL) during the first storm event, April 8-9. The report contains the high-density network precipitation chemistry data, air chemistry data from the PNL aircraft, and meteorological data for the event, including standard National Weather Service products and radar data from the network. 4 references, 72 figures, 5 tables.

Dengue viruses in Brazil, 1986-2006 Virus del dengue en Brasil, 1986-2006

Directory of Open Access Journals (Sweden)

Rita Maria Ribeiro Nogueira

2007-11-01

Full Text Available A total of 4 243 049 dengue cases have been reported in Brazil between 1981 and 2006, including 5 817 cases of dengue hemorrhagic fever/dengue shock syndrome (DHF/DSS and a total of 338 fatal cases. Although all Brazilian regions have been affected, the Northeast and Southeast regions have registered the highest number of notifications. DENV-1 and DENV-4 were isolated for the first time in the Amazon region of Brazil in 1981 and 1982. The disease became a nationwide public health problem following outbreaks of DENV-1 and DENV-2 in the state of Rio de Janeiro in 1986 and 1990, respectively. The introduction of DENV-3 in 2000, also in the state of Rio de Janeiro, led to a severe epidemic with 288 245 reported dengue cases, including 91 deaths. Virus strains that were typed during the 2002 epidemic show that DENV-3 has displaced other dengue virus serotypes and entered new areas, a finding that warrants closer evaluation. Unusual clinical symptoms, including central nervous system involvement, have been observed in dengue patients in at least three regions of the country.En Brasil se han notificado 4 243 049 casos de dengue entre 1981 y 2006, de ellos 5 817 casos de dengue hemorrágico/síndrome de choque por dengue (DH/SCD y un total de 338 casos mortales. A pesar de que la enfermedad ha afectado a todas las regiones brasileñas, el mayor número de casos se ha notificado en las regiones nororiental y suroriental. Los virus del dengue (DENV 1 y 4 se aislaron por primera vez en la región amazónica de Brasil en 1981 y 1982. La enfermedad se convirtió en un problema nacional de salud pública después de los brotes de DENV-1 y DENV-2 en el Estado de Río de Janeiro en 1986 y 1990, respectivamente. La introducción del DENV-3 en 2000, también en el Estado de Río de Janeiro, llevó a una grave epidemia con 288 245 casos notificados de dengue y 91 muertes. Las cepas del virus identificadas durante la epidemia de 2002 demostraron que el DENV-3 ha

Gallium Arsenide and Related Compounds, 1986.

Science.gov (United States)

1986-01-01

F-Yiuang, WL,, PK Rhattacharva, UDas, A Chin , IJlackson and D L Persechini 417 -422 High quality lattice matched lnGaAs/InP heterostructures prepared...Sci. Technol. B3 1162. Schwartz G. P. 1983 Thin solid Films 103 3. Spicer W. E., Lindau I., Skeath P. R., Su C Y. and Chye P. W. 19R0 Phys. Rev. Lett... Chin R, Nakano K, and Milano R A 1981 IEEE J. Quantum Electron. QEJJ7, 275. Murgatroyd I J, Norman A G, and Booker G R 1986 Phys. Rev. Lett

Environmental monitoring at Argonne National Laboratory. Annual report, 1981

International Nuclear Information System (INIS)

Golchert, N.W.; Duffy, T.L.; Sedlet, J.

1982-03-01

The results of the environmental monitoring program at Argonne National Laboratory for 1981 are presented and discussed. To evaluate the effect of Argonne operations on the environment, measurements were made for a variety of radionuclides in air, surface water, soil, grass, bottom sediment, and milk; for a variety of chemical constituents in air, surface water, and Argonne effluent water; and of the environmental penetrating radiation dose. Sample collections and measurements were made at the site boundary and off the Argonne site for comparison purposes. Some on-site measurements were made to aid in the interpretation of the boundary and off-site data. The results of the program are interpreted in terms of the sources and origin of the radioactive and chemical substances (natural, fallout, Argonne, and other) and are compared with applicable environmental quality standards. The potential radiation dose to off-site population groups is also estimated

[National Congress of American Indians]: Final 1985-1986 progress report, March 1, 1986-October 7, 1986

International Nuclear Information System (INIS)

1986-01-01

This quarterly report summarizes the activities of the National Congress of American Indians NCAI Fund program to disseminate information and provide technical assistance to American Indian governments regarding nuclear waste management, site selection and transportation issues. The report covers the grant period March 1, 1986, to October 7, 1986, which includes the no-cost extension granted in March of 1986 and the grant amendment for July 3 to October 3, 1986. During this period, the project held three national meetings of the National Indian Nuclear Waste Policy Committee (NINWPC); monitored the DOE Office of Civilian Radioactive Waste Management (OCRWM) program and congressional activity and provided information to the tribes; published five issues of the Sentinel/Bulletin - NCAI News, which included a number of articles on nuclear waste; provided informational mailings to the NINWPC representatives; attended and coordinated meetings between the tribes, Department of Energy (DOE), Nuclear Regulatory Commission (NRC), the Bureau of Indian Affairs (BIA), Environmental Protection Agency (EPA), and Sandia National Laboratories; and provided speakers to conferences and groups

1981 environmental monitoring report

International Nuclear Information System (INIS)

Naidu, J.R.; Olmer, L.L.

1982-04-01

The environmental levels of radioactivity and other pollutants found in the vicinity of BNL during 1981 are summarized in this report. As an aid in the interpretation of the data, the amounts of radioactivity and other pollutants released in airborne and liquid effluents from Laboratory facilities to the environment are also indicated. The environmental data includes external radiation levels; radioactive air particulates; tritium and iodine concentrations; the amounts and concentrations of radioactivity in and the water quality of the stream into which liquid effluents are released; the concentrations of radioactivity in sediments and biota from the stream; the concentrations of radioactivity in and the water quality of ground waters underlying the Laboratory; and concentrations of radioactivity in milk samples obtained in the vicinity of the Laboratory. 28 references, 9 figures, 20 tables

Current Status of Groundwater Monitoring Networks in Korea

OpenAIRE

Jin-Yong Lee; Kideok D. Kwon

2016-01-01

Korea has been operating groundwater monitoring systems since 1996 as the Groundwater Act enacted in 1994 enforces nationwide monitoring. Currently, there are six main groundwater monitoring networks operated by different government ministries with different purposes: National Groundwater Monitoring Network (NGMN), Groundwater Quality Monitoring Network (GQMN), Seawater Intrusion Monitoring Network (SIMN), Rural Groundwater Monitoring Network (RGMN), Subsidiary Groundwater Monitoring Network ...

Neutron monitor latitude survey of cosmic ray intensity during the 1986/1987 solar minimum

International Nuclear Information System (INIS)

Moraal, H.; Potgieter, M.S.; Stoker, P.H.; van der Walt, A.J.

1989-01-01

A latitude survey of the cosmic ray intensity at sea level was conducted during the 1986/1987 solar minimum period on commercial vessels of the South African Marine Corporation (SAFMARINE). The results show that the differential response function for the 1986/1987 solar minimum agrees well with that measured in 1965. Both these response functions are significantly lower than those for 1976 and 1954. This result supports the 22-year modulation cycle as predicted, for example, by models including drift effects of the charged cosmic ray particles in the large-scale interplanetary magnetic field. A crossover of the spectra at rigidities of about 7 GV was also observed. Such a crossover is necessary to explain both the stationary neutron monitor counting rates and the lower-energy balloon and space observations in consecutive solar cycles. copyright American Geophysical Union 1989

Current Status of Groundwater Monitoring Networks in Korea

Directory of Open Access Journals (Sweden)

Jin-Yong Lee

2016-04-01

Full Text Available Korea has been operating groundwater monitoring systems since 1996 as the Groundwater Act enacted in 1994 enforces nationwide monitoring. Currently, there are six main groundwater monitoring networks operated by different government ministries with different purposes: National Groundwater Monitoring Network (NGMN, Groundwater Quality Monitoring Network (GQMN, Seawater Intrusion Monitoring Network (SIMN, Rural Groundwater Monitoring Network (RGMN, Subsidiary Groundwater Monitoring Network (SGMN, and Drinking Water Monitoring Network (DWMN. The Networks have a total of over 3500 monitoring wells and the majority of them are now equipped with automatic data loggers and remote terminal units. Most of the monitoring data are available to the public through internet websites. These Networks have provided scientific data for designing groundwater management plans and contributed to securing the groundwater resource particularly for recent prolonged drought seasons. Each Network, however, utilizes its own well-specifications, probes, and telecommunication protocols with minimal communication with other Networks, and thus duplicate installations of monitoring wells are not uncommon among different Networks. This mini-review introduces the current regulations and the Groundwater Monitoring Networks operated in Korea and provides some suggestions to improve the sustainability of the current groundwater monitoring system in Korea.

Monitoring of radioactivity in the environs of Finnish nuclear power stations in 1986

International Nuclear Information System (INIS)

Ilus, E.; Sjoeblom, K.L.; Aaltonen, H.; Klemola, S.; Arvela, H.

1987-06-01

Results of the environmental programmes monitoring radioactivity around the Finnish nuclear power stations in 1986 are reported. After the end of April the fallout nuclides from the Chernobyl accident predominated in all samples taken from the environs of the two power stations Loviisa and Olkiluoto. Radionuclides originating from the Finnish power stations were detected mainly in samples taken from the aquatic environment. The concentrations of the locally discharged nuclides were very low in comparison with the fallout nuclides and their impact on the radiation doses of the population was insignificant. Both nuclear power stations are situated in the main fallout area in Finland. The results of these large monitoring programmes give a good picture of the behaviour of the Chernobyl fallout in the specific areas in Finland

The Community Environmental Monitoring Program in the 21st Century: The Evolution of a Monitoring Network

International Nuclear Information System (INIS)

Hartwell, W.T.; Tappen, J.; Karr, L.

2007-01-01

This paper focuses on the evolution of the various operational aspects of the Community Environmental Monitoring Program (CEMP) network following the transfer of program administration from the U.S. Environmental Protection Agency (EPA) to the Desert Research Institute (DRI) of the Nevada System of Higher Education in 1999-2000. The CEMP consists of a network of 29 fixed radiation and weather monitoring stations located in Nevada, Utah, and California. Its mission is to involve stakeholders directly in monitoring for airborne radiological releases to the off site environment as a result of past or ongoing activities on the Nevada Test Site (NTS) and to make data as transparent and accessible to the general public as feasible. At its inception in 1981, the CEMP was a cooperative project of the U.S. Department of Energy (DOE), DRI, and EPA. In 1999-2000, technical administration of the CEMP transitioned from EPA to DRI. Concurrent with and subsequent to this transition, station and program operations underwent significant enhancements that furthered the mission of the program. These enhancements included the addition of a full suite of meteorological instrumentation, state-of-the-art electronic data collectors, on-site displays, and communications hardware. A public website was developed. Finally, the DRI developed a mobile monitoring station that can be operated entirely on solar power in conjunction with a deep-cell battery, and includes all meteorological sensors and a pressurized ion chamber for detecting background gamma radiation. Final station configurations have resulted in the creation of a platform that is well suited for use as an in-field multi-environment test-bed for prototype environmental sensors and in interfacing with other scientific and educational programs. Recent and near-future collaborators have included federal, state, and local agencies in both the government and private sectors. The CEMP also serves as a model for other programs wishing to

Monitoring of radioactive contamination in food and the environment 1986-1998

International Nuclear Information System (INIS)

Liland, Astrid; Skuterud, Lavrans; Bergan, Tone; Forseth, Torbjoern; Gaare, Eldar; Hellstroem, Turid

2001-01-01

The results from the national monitoring of radioactive contamination in food and the environment 1986-1998 are presented. The average 137Cs concentration is decreasing in cow's and goat's milk, sheep, reindeer and fresh water fish. Pasture and fungi are, on the contrary, not showing a general decreasing trend. The radioactivity in food and humans has been decreasing since 1987. The effective dose from intake is estimated to 0.02 mSv for an average Norwegian in 1998. Vulnerable groups may have received doses up to 0.4 mSv. One cannot rule out the possibility that some individuals in these groups have received doses superior to 1 mSv/year. (Author)

Source mechanisms of persistent shallow earthquakes during eruptive and non-eruptive periods between 1981 and 2011 at Mount St. Helens, Washington

Science.gov (United States)

Lehto, Heather L.; Roman, Diana C.; Moran, Seth C.

2013-01-01

Shallow seismicity between 0 and 3-km depth has persisted at Mount St. Helens, Washington (MSH) during both eruptive and non-eruptive periods for at least the past thirty years. In this study we investigate the source mechanisms of shallow volcano-tectonic (VT) earthquakes at MSH by calculating high-quality hypocenter locations and fault plane solutions (FPS) for all VT events recorded during two eruptive periods (1981–1986 and 2004–2008) and two non-eruptive periods (1987–2004 and 2008–2011). FPS show a mixture of normal, reverse, and strike-slip faulting during all periods, with a sharp increase in strike-slip faulting observed in 1987–1997 and an increase in normal faulting in 1998–2004. FPS P-axis orientations show a ~ 90° rotation with respect to regional σ1 (N23°E) during 1981–1986 and 2004–2008, bimodal orientations (~ N-S and ~ E-W) during 1987–2004, and bimodal orientations at ~ N-E and ~ S-W from 2008–2011. We interpret these orientations to likely be due to pressurization accompanying the shallow intrusion and subsequent eruption of magma as domes during 1981–1986 and 2004–2008 and the buildup of pore pressure beneath a seismogenic volume (located at 0–1 km) with a smaller component due to the buildup of tectonic forces during 1987–2004 and 2008–2011.

WiMAX network performance monitoring & optimization

DEFF Research Database (Denmark)

Zhang, Qi; Dam, H

2008-01-01

frequency reuse, capacity planning, proper network dimensioning, multi-class data services and so on. Furthermore, as a small operator we also want to reduce the demand for sophisticated technicians and man labour hours. To meet these critical demands, we design a generic integrated network performance......In this paper we present our WiMAX (worldwide interoperability for microwave access) network performance monitoring and optimization solution. As a new and small WiMAX network operator, there are many demanding issues that we have to deal with, such as limited available frequency resource, tight...... this integrated network performance monitoring and optimization system in our WiMAX networks. This integrated monitoring and optimization system has such good flexibility and scalability that individual function component can be used by other operators with special needs and more advanced function components can...

Air quality monitoring at Seoul, Korea as a part of East-Asian air surveillance network

International Nuclear Information System (INIS)

Hashimoto, Y.; Sekine, Y.; Kim, H.K.; Otoshi, T.

1989-01-01

Global scale air pollution study is a recent trend due to a perception that air pollution is changing climate and other essential earth's conditions that could seriously affect our lives. One of the important tasks which can contribute to protect our natural environment must be to know about the present and changing air quality. For this purpose, a regional air monitoring plan was designed by a research group and has proceeded to set up stations in the eastern Asia including Japan, Korea and China to get continuous data which can contribute to world wide data base of air quality. This project was initiated at Seoul, Korea in April, 1986 by the method of National Air Surveillance Network, Japan. Airborne particles were collected by so-called Hi-vol and Lo-vol, and their components were analyzed by neutron activation analysis and others. The results of Seoul sampling as a first step of this network plan are presented

Nuclear safety activities in the SR of Slovenia in 1986

Energy Technology Data Exchange (ETDEWEB)

Susnik, J [Inst. Jozef Stefan, Ljubljana (Slovenia)

1987-06-15

Currently Yugoslavia has one 632 MWe nuclear power plant (NPP) of PWR design, located at Krsko in the Socialist Republic (SR) of Slovenia. Krsko NPP, which is a two-loop plant, started power operation in 1981. In general, reactor safety activities in the SR of Slovenia are mostly related to upgrading the safety of our Krsko NPP and to developing capabilities for use in future units. This report presents the nuclear safety related legislation and organization of the corresponding regulatory body, and the activities related to nuclear safety of the participating organizations in the SR of Slovenia in 1986. (author)

Nuclear safety activities in the SR of Slovenia in 1986

International Nuclear Information System (INIS)

Susnik, J.

1987-06-01

Currently Yugoslavia has one 632 MWe nuclear power plant (NPP) of PWR design, located at Krsko in the Socialist Republic (SR) of Slovenia. Krsko NPP, which is a two-loop plant, started power operation in 1981. In general, reactor safety activities in the SR of Slovenia are mostly related to upgrading the safety of our Krsko NPP and to developing capabilities for use in future units. This report presents the nuclear safety related legislation and organization of the corresponding regulatory body, and the activities related to nuclear safety of the participating organizations in the SR of Slovenia in 1986. (author)

Entropy Applications to Water Monitoring Network Design: A Review

Directory of Open Access Journals (Sweden)

Jongho Keum

2017-11-01

Full Text Available Having reliable water monitoring networks is an essential component of water resources and environmental management. A standardized process for the design of water monitoring networks does not exist with the exception of the World Meteorological Organization (WMO general guidelines about the minimum network density. While one of the major challenges in the design of optimal hydrometric networks has been establishing design objectives, information theory has been successfully adopted to network design problems by providing measures of the information content that can be deliverable from a station or a network. This review firstly summarizes the common entropy terms that have been used in water monitoring network designs. Then, this paper deals with the recent applications of the entropy concept for water monitoring network designs, which are categorized into (1 precipitation; (2 streamflow and water level; (3 water quality; and (4 soil moisture and groundwater networks. The integrated design method for multivariate monitoring networks is also covered. Despite several issues, entropy theory has been well suited to water monitoring network design. However, further work is still required to provide design standards and guidelines for operational use.

Network Monitoring as a Streaming Analytics Problem

KAUST Repository

Gupta, Arpit

2016-11-02

Programmable switches make it easier to perform flexible network monitoring queries at line rate, and scalable stream processors make it possible to fuse data streams to answer more sophisticated queries about the network in real-time. Unfortunately, processing such network monitoring queries at high traffic rates requires both the switches and the stream processors to filter the traffic iteratively and adaptively so as to extract only that traffic that is of interest to the query at hand. Others have network monitoring in the context of streaming; yet, previous work has not closed the loop in a way that allows network operators to perform streaming analytics for network monitoring applications at scale. To achieve this objective, Sonata allows operators to express a network monitoring query by considering each packet as a tuple and efficiently partitioning each query between the switches and the stream processor through iterative refinement. Sonata extracts only the traffic that pertains to each query, ensuring that the stream processor can scale traffic rates of several terabits per second. We show with a simple example query involving DNS reflection attacks and traffic traces from one of the world\\'s largest IXPs that Sonata can capture 95% of all traffic pertaining to the query, while reducing the overall data rate by a factor of about 400 and the number of required counters by four orders of magnitude. Copyright 2016 ACM.

Results of the 1986 FFTF inherent safety tests

International Nuclear Information System (INIS)

Burke, T.M.; Campbell, L.R.; Franz, G.R.; Knecht, W.L.

1987-01-01

A series of tests was recently completed at the 400-MW (thermal) Fast Flux Test Facility (FFTF) to further demonstrate the passive safety characteristics of liquid-metal-cooled fast reactors. Earlier FFTF testing of decay heat removal by sodium natural circulation was reported in 1981. The main purpose of the 1986 test series was to demonstrate passive reactor shutdown during a loss-of-flow event when several inherent shutdown devices called gas expansion modules (GEMs) were installed in the reactor. However, these tests also provide further data on the natural circulation performance of the primary system, in particular the reactor core, and thus add to the data base available for checking the validity of available analytical tools

Wireless air monitoring network with new AMIZ-2004G dust monitors

International Nuclear Information System (INIS)

Jakowiuk, A.; Machaj, B.; Pienkos, P.; Swistowski, E.

2006-01-01

The principle of operation of the dust monitors is based on determination of dust mass deposited on air filters from known volumes of air samples. The dust mass is determined from radiation attenuation of a Pm-147 beta source. MIZA and AMIZ monitors produced in the Institute of Nuclear Chemistry and Technology, Warsaw (Poland) additionally measure relative humidity, atmospheric pressure and temperature of the air. In case the measurements are made in a few different places, direct collection of the results requires that personnel of the environment protection units has to go frequently to the monitors and collect the data. To improve the data transmission, a new version of the AMIZ-2004G monitor was developed which is equipped with a GSM modem enabling communication with a central computer. Thanks to the new construction not only a remote wireless communication with AMIZ is possible, but also a monitoring network containing a higher number of dust monitors can be made. The measuring data from all the monitors in the network can now be collected in one central computer equipped with the GSM modem and a proper acquisition program. In 2005, two such monitoring networks were put into operation

Geo mathematic tools for the design of a radioisotopes monitoring network in order to modelling the groundwater dynamics processes and hydrodynamic management

International Nuclear Information System (INIS)

Peralta, J.L.; Gil, R.; Leyva, D.; Molerio, L.F.; Pin, M.

2004-01-01

The present paper, shows the application of geo mathematic tools [Mangin,1981; Molerio,1997] for the design of a radioisotopes monitoring network in order to modelling the groundwater dynamics processes and hydrodynamic management of a Karstic Basin (Almendares-Vento watershed), which is very difficult to evaluate due to the physical-geographical, geologic and hydrogeological characteristics. The Almendares Vento watershed (AVW) is close to the Jaruco-Aguacate watershed, with a similar hydrogeologic and geologic structure, therefore similar result must be expected. In the AVW case is necessary to identify, with more precision, the water propagation limits of the stratified layers according to the waters transit times, recharges and dynamics aquifers, residence time, groundwater contamination and the groundwater-surface water interaction due to the dam placed on the basin. The paper allowed the identification of a monitoring points network, taking into account, between other statistical approaches, the good correlation, the high memory effect, etc. According to the analysis of the variances spectral, have been obtained and optimized the sampling frequency of the network points in the Basin. Besides, it have been identified the necessities to include the detailed evaluation of a specific point of the network in the hydrodynamic study (Vento watershed). In order to evaluate the optimization of the designed monitoring network, the geo mathematic study developed was compared with the results of the mathematical model AQUIMPE, the final result showed the validation of the obtained design. The results of the work allow the best monitoring of the parameters in order to determine the aquifer recharge, residence times, the vulnerability to the waters contamination and the groundwater-surface water interaction

Promoting Social Network Awareness: A Social Network Monitoring System

Science.gov (United States)

Cadima, Rita; Ferreira, Carlos; Monguet, Josep; Ojeda, Jordi; Fernandez, Joaquin

2010-01-01

To increase communication and collaboration opportunities, members of a community must be aware of the social networks that exist within that community. This paper describes a social network monitoring system--the KIWI system--that enables users to register their interactions and visualize their social networks. The system was implemented in a…

Network performance of a wireless sensor network for temperature monitoring in vineyards

DEFF Research Database (Denmark)

Liscano, Ramiro; Jacoub, John Khalil; Dersingh, Anand

2011-01-01

Wireless sensor networks (WSNs) are an emerging technology which can be used for outdoor environmental monitoring. This paper presents challenges that arose from the development and deployment of a WSN for environmental monitoring as well as network performance analysis of this network. Different...... components in our sensor network architecture are presented like the physical nodes, the sensor node code, and two messaging protocols; one for collecting sensor and network values and the other for sensor node commands. An information model for sensor nodes to support plug-and-play capabilities in sensor...... networks is also presented....

Changes in energy intensities of Thai industry between 1981 and 2000: a decomposition analysis

International Nuclear Information System (INIS)

Bhattacharyya, S.C.; Ussanarassamee, Arjaree

2005-01-01

Industrial demand accounts for about 30% of total final energy demand in Thailand, which experienced rapid increases in energy demand. This paper analyzes the changes in industrial energy intensities over a period of 20 years (1981-2000) and identifies the factors affecting the energy consumption using logarithmic mean Divisia decomposition technique. It is found that Thai industry has passed through four different phases of growth and energy consumption has closely followed the industrial growth pattern. Energy intensity of Thai industry decreased from 17.6 toe/million baht (constant 1988 prices) in 1981 to 15.8 toe/million baht (1988 prices) in 2000. Non-metallic mineral industry is the most intensive industry followed by basic metal, food and beverage, chemical and paper industries. The factor analysis indicates that both the structural effect and intensity effect contributed to a decline of aggregate intensity by 8% during 1981-1986 but in the rest of the periods, the two effects acted in opposite directions and thereby reducing the overall effect on aggregate intensity. Food and beverages, non-metallic mineral and chemical industries had significantly influenced the changes in aggregate intensity at sectoral level

Smolt Monitoring Program, Volume II, Migrational Characteristics of Columbia Basin Salmon and Steelhead Trout, 1986 Annual Report.

Energy Technology Data Exchange (ETDEWEB)

Fish Passage Center

1987-02-01

Smolt Monitoring Program Annual Report, 1986, Volume I, describes the results of travel time monitoring and other migrational characteristics of yearling and sub-yearling chinook salmon (Oncorhynchus tshawytscha), sockeye salmon (Oncorhynchus nerka), and steelhead trout (Salmo gairdneri). This volume presents the data from Fish Passage Center freeze brands used in the analysis of travel time for Lewiston, Lower Granite, Lower Monumental, Rock Island, McNary, and John Day dams. Summary of data collection procedures and explanation of data listings are presented in conjunction with the mark recapture data. Data for marked fish not presented in this report will be provided upon request. Daily catch statistics (by species), flow, and sample parameters for the smolt monitoring sites, Clearwater, Lewiston, Lower Granite, Lower Monumental, Rock Island, McNary, John Day, and Bonneville also will be provided upon request.

Progress and lessons learned from water-quality monitoring networks

Science.gov (United States)

Myers, Donna N.; Ludtke, Amy S.

2017-01-01

Stream-quality monitoring networks in the United States were initiated and expanded after passage of successive federal water-pollution control laws from 1948 to 1972. The first networks addressed information gaps on the extent and severity of stream pollution and served as early warning systems for spills. From 1965 to 1972, monitoring networks expanded to evaluate compliance with stream standards, track emerging issues, and assess water-quality status and trends. After 1972, concerns arose regarding the ability of monitoring networks to determine if water quality was getting better or worse and why. As a result, monitoring networks adopted a hydrologic systems approach targeted to key water-quality issues, accounted for human and natural factors affecting water quality, innovated new statistical methods, and introduced geographic information systems and models that predict water quality at unmeasured locations. Despite improvements, national-scale monitoring networks have declined over time. Only about 1%, or 217, of more than 36,000 US Geological Survey monitoring sites sampled from 1975 to 2014 have been operated throughout the four decades since passage of the 1972 Clean Water Act. Efforts to sustain monitoring networks are important because these networks have collected information crucial to the description of water-quality trends over time and are providing information against which to evaluate future trends.

Environmental radiation levels around Nuclear Fuel Complex, Hyderabad during 1981-1988

International Nuclear Information System (INIS)

Mehta, Navnit; Lakshmanan, A.R.; Kathuria, S.P.; Nambi, K.S.V.

1989-01-01

This report presents environmental radiation monitoring results around Nuclear Ffuel Complex (NFC) at Hyderabad for the period, 1981-'88. During 1981-'83 only indoor radiations were monitored at 12 locations in the region of about 15 km. radius around NFC plant. However, during 1984-'88 both indoor and outdoor monitoring was done in a standardised manner at 8 locations. In this routine monitoring programme, environmental thermoluminescent dosimeters were used in quarterly integrating cycles. The average outdoor natural radiation level around NFC during 1984-'88 is found to be 227 ± 34 (σ) mR/y, which is the highest among the various sites in the country where DAE units are located. Such a high level of natural background radiation in and around Hyderabad is due to granitic terrains which normally have significant amounts of primordial radioactivity. The indoor to outdoor radiation ratio is found to be 1.35 ± 0.1 (σ). Application of this ratio on all the available indoor radiation monitoring results of 1981-'88 gives an estimate of 230 ± 26 mR/y as the average outdoor radiation level, and this is in very close agreement with the directly measured value mentioned earlier. The temporal variations seen in the quarterly results of each location have been tested for Normal and Log-Normal distributions and found to yield satisfactory correlations, although the plots reveal slight skewness; the latter however, could not be attributed to the NFC operations. (author). 7 refs., 4 tabs., 12 figs

Comparison of precipitation chemistry measurements obtained by the Canadian Air and Precipitation Monitoring Network and National Atmospheric Deposition Program for the period 1995-2004

Science.gov (United States)

Wetherbee, Gregory A.; Shaw, Michael J.; Latysh, Natalie E.; Lehmann, Christopher M.B.; Rothert, Jane E.

2010-01-01

Precipitation chemistry and depth measurements obtained by the Canadian Air and Precipitation Monitoring Network (CAPMoN) and the US National Atmospheric Deposition Program/National Trends Network (NADP/NTN) were compared for the 10-year period 1995–2004. Colocated sets of CAPMoN and NADP instrumentation, consisting of precipitation collectors and rain gages, were operated simultaneously per standard protocols for each network at Sutton, Ontario and Frelighsburg, Ontario, Canada and at State College, PA, USA. CAPMoN samples were collected daily, and NADP samples were collected weekly, and samples were analyzed exclusively by each network’s laboratory for pH, H + , Ca2+  , Mg2+  , Na + , K + , NH+4 , Cl − , NO−3 , and SO2−4 . Weekly and annual precipitation-weighted mean concentrations for each network were compared. This study is a follow-up to an earlier internetwork comparison for the period 1986–1993, published by Alain Sirois, Robert Vet, and Dennis Lamb in 2000. Median weekly internetwork differences for 1995–2004 data were the same to slightly lower than for data for the previous study period (1986–1993) for all analytes except NO−3 , SO2−4 , and sample depth. A 1994 NADP sampling protocol change and a 1998 change in the types of filters used to process NADP samples reversed the previously identified negative bias in NADP data for hydrogen-ion and sodium concentrations. Statistically significant biases (α = 0.10) for sodium and hydrogen-ion concentrations observed in the 1986–1993 data were not significant for 1995–2004. Weekly CAPMoN measurements generally are higher than weekly NADP measurements due to differences in sample filtration and field instrumentation, not sample evaporation, contamination, or analytical laboratory differences.

BAKNET - Communication network for radiation monitoring devices

International Nuclear Information System (INIS)

Cohen, Y.; Wengrowicz, U.; Tirosh, D.; Barak, D.

1997-01-01

A system, based on a new concept of controlling and monitoring distributed radiation monitors, has been developed and approved at the NRCN. The system, named B AKNET Network , consists of a series of communication adapters connected to a main PC via an RS-485 communication network (see Fig. 1). The network's maximal length is 1200 meters and it enables connection of up to 128 adapters. The BAKNET adapters are designed to interface output signals of different types of stationary radiation monitors to a main PC. The BAKNET adapters' interface type includes: digital, analog, RS-232, and mixed output signals. This allows versatile interfacing of different stationary radiation monitors to the main computer. The connection to the main computer is via an RS-485 network, utilizing an identical communication protocol. The PC software, written in C ++ under MS-Windows, consists of two main programs. The first is the data collection program and the second is the Human Machine Interface (HMI). (authors)

Integrating wireless sensor network for monitoring subsidence phenomena

Science.gov (United States)

Marturià, Jordi; Lopez, Ferran; Gigli, Giovanni; Intrieri, Emanuele; Mucchi, Lorenzo; Fornaciai, Alessandro

2016-04-01

An innovative wireless sensor network (WSN) for the 3D superficial monitoring of deformations (such as landslides and subsidence) is being developed in the frame of the Wi-GIM project (Wireless sensor network for Ground Instability Monitoring - LIFE12 ENV/IT/001033). The surface movement is detected acquiring the position (x, y and z) by integrating large bandwidth technology able to detect the 3D coordinates of the sensor with a sub-meter error, with continuous wave radar, which allows decreasing the error down to sub-cm. The Estació neighborhood in Sallent is located over the old potassium mine Enrique. This zone has been affected by a subsidence process over more than twenty years. The implementation of a wide network for ground auscultation has allowed monitoring the process of subsidence since 1997. This network consists of: i) a high-precision topographic leveling network to control the subsidence in surface; ii) a rod extensometers network to monitor subsurface deformation; iii) an automatic Leica TCA Total Station to monitor building movements; iv) an inclinometers network to measure the horizontal displacements on subsurface and v) a piezometer to measure the water level. Those networks were implemented within an alert system for an organized an efficient response of the civil protection authorities in case of an emergency. On 23rd December 2008, an acceleration of subsoil movements (of approx. 12-18 cm/year) provoked the activation of the emergency plan by the Catalan Civil Protection. This implied the preventive and scheduled evacuation of the neighbours (January 2009) located in the area with a higher risk of collapse: around 120 residents of 43 homes. As a consequence, the administration implemented a compensation plan for the evacuation of the whole neighbourhood residents and the demolition of 405 properties. In this work, the adaptation and integration process of Wi-GIM system with those conventional monitoring network are presented for its testing

AAEC tritium list no. 5 1981-1982

International Nuclear Information System (INIS)

Calf, G.E.; Stokes, R.C.

1983-06-01

Details are given of the concentration of the environmental isotope tritium in monthly precipitation samples taken at 16 stations, situated throughout Australia, during the period 1981-1982. Tritium levels in Australia have now been estimated for 13 years. The results show a significant decrease in tritium concentration in rainfall at all monitoring stations

Host Event Based Network Monitoring

Energy Technology Data Exchange (ETDEWEB)

Jonathan Chugg

2013-01-01

The purpose of INL’s research on this project is to demonstrate the feasibility of a host event based network monitoring tool and the effects on host performance. Current host based network monitoring tools work on polling which can miss activity if it occurs between polls. Instead of polling, a tool could be developed that makes use of event APIs in the operating system to receive asynchronous notifications of network activity. Analysis and logging of these events will allow the tool to construct the complete real-time and historical network configuration of the host while the tool is running. This research focused on three major operating systems commonly used by SCADA systems: Linux, WindowsXP, and Windows7. Windows 7 offers two paths that have minimal impact on the system and should be seriously considered. First is the new Windows Event Logging API, and, second, Windows 7 offers the ALE API within WFP. Any future work should focus on these methods.

Environmental surveillance at Los Alamos during 1986

International Nuclear Information System (INIS)

1987-04-01

This report describes the environmental surveillance program conducted by Los Alamos National Laboratory during 1986. Routine monitoring for radiation and radioactive or chemical materials is conducted on the Laboratory site as well as in the surrounding region. Monitoring results are used to determine compliance with appropriate standards and to permit eartly identification of potentially undesirable trends. Results and interpertation of data for 1986 cover: external penetrating radiation; quantities of airborne emissions and liquid effluents; concentrations of chemicals and radionuclides in ambient air, surface and ground waters, municipal water supply, soils and sediments, and foodstuffs; and environmental compliance. Comparison with appropriate standards, regulations, and backgound levels provide the basis for concluding that environmental effects from Laboratory operations are insignificant and do not impact the public, Laboratory employees, or the environment. 52 refs., 32 figs., 117 tabs

Efficient network monitoring for large data acquisition systems

International Nuclear Information System (INIS)

Savu, D.O.; Martin, B.; Al-Shabibi, A.; Sjoen, R.; Batraneanu, S.M.; Stancu, S.N.

2012-01-01

Though constantly evolving and improving, the available network monitoring solutions have limitations when applied to the infrastructure of a high speed realtime data acquisition (DAQ) system. DAQ networks are particular computer networks where experts have to pay attention to both individual subsections as well as system wide traffic flows while monitoring the network. The ATLAS Network at the Large Hadron Collider (LHC) has more than 200 switches interconnecting 3500 hosts and totaling 8500 high speed links. The use of heterogeneous tools for monitoring various infrastructure parameters, in order to assure optimal DAQ system performance, proved to be a tedious and time consuming task for experts. To alleviate this problem we used our networking and DAQ expertise to build a flexible and scalable monitoring system providing an intuitive user interface with the same look and feel irrespective of the data provider that is used. Our system uses custom developed components for critical performance monitoring and seamlessly integrates complementary data from auxiliary tools, such as NAGIOS, information services or custom databases. A number of techniques (e.g. normalization, aggregation and data caching) were used in order to improve the user interface response time. The end result is a unified monitoring interface, for fast and uniform access to system statistics, which significantly reduced the time spent by experts for ad-hoc and post-mortem analysis. (authors)

An acoustical model based monitoring network

NARCIS (Netherlands)

Wessels, P.W.; Basten, T.G.H.; Eerden, F.J.M. van der

2010-01-01

In this paper the approach for an acoustical model based monitoring network is demonstrated. This network is capable of reconstructing a noise map, based on the combination of measured sound levels and an acoustic model of the area. By pre-calculating the sound attenuation within the network the

Optimizing Groundwater Monitoring Networks Using Integrated Statistical and Geostatistical Approaches

Directory of Open Access Journals (Sweden)

Jay Krishna Thakur

2015-08-01

Full Text Available The aim of this work is to investigate new approaches using methods based on statistics and geo-statistics for spatio-temporal optimization of groundwater monitoring networks. The formulated and integrated methods were tested with the groundwater quality data set of Bitterfeld/Wolfen, Germany. Spatially, the monitoring network was optimized using geo-statistical methods. Temporal optimization of the monitoring network was carried out using Sen’s method (1968. For geostatistical network optimization, a geostatistical spatio-temporal algorithm was used to identify redundant wells in 2- and 2.5-D Quaternary and Tertiary aquifers. Influences of interpolation block width, dimension, contaminant association, groundwater flow direction and aquifer homogeneity on statistical and geostatistical methods for monitoring network optimization were analysed. The integrated approach shows 37% and 28% redundancies in the monitoring network in Quaternary aquifer and Tertiary aquifer respectively. The geostatistical method also recommends 41 and 22 new monitoring wells in the Quaternary and Tertiary aquifers respectively. In temporal optimization, an overall optimized sampling interval was recommended in terms of lower quartile (238 days, median quartile (317 days and upper quartile (401 days in the research area of Bitterfeld/Wolfen. Demonstrated methods for improving groundwater monitoring network can be used in real monitoring network optimization with due consideration given to influencing factors.

Network monitoring module of BES III system environment

International Nuclear Information System (INIS)

Song Liwen; Zhao Jingwei; Zhang Bingyun

2002-01-01

In order to meet the needs of the complicated network architecture of BES III (Beijing Spectrometer III) and make sure normal online running in the future, it is necessary to develop a multi-platforms Network Monitoring Tool which can help system administrator monitor and manage BES III network. The author provides a module that can monitor not only the traffic of switch-router's ports but also the performance status of key devices in the network environment, meanwhile it can also give warning to manager and submit the related reports. the great sense, the theory basis, the implementing method and the graph in formation of this tool will be discussed

Implementation of medical monitor system based on networks

Science.gov (United States)

Yu, Hui; Cao, Yuzhen; Zhang, Lixin; Ding, Mingshi

2006-11-01

In this paper, the development trend of medical monitor system is analyzed and portable trend and network function become more and more popular among all kinds of medical monitor devices. The architecture of medical network monitor system solution is provided and design and implementation details of medical monitor terminal, monitor center software, distributed medical database and two kind of medical information terminal are especially discussed. Rabbit3000 system is used in medical monitor terminal to implement security administration of data transfer on network, human-machine interface, power management and DSP interface while DSP chip TMS5402 is used in signal analysis and data compression. Distributed medical database is designed for hospital center according to DICOM information model and HL7 standard. Pocket medical information terminal based on ARM9 embedded platform is also developed to interactive with center database on networks. Two kernels based on WINCE are customized and corresponding terminal software are developed for nurse's routine care and doctor's auxiliary diagnosis. Now invention patent of the monitor terminal is approved and manufacture and clinic test plans are scheduled. Applications for invention patent are also arranged for two medical information terminals.

Monitoring Malware Activity on the LAN Network

Science.gov (United States)

Skrzewski, Mirosław

Many security related organizations periodically publish current network and systems security information, with the lists of top malware programs. These lists raises the question how these threats spreads out, if the worms (the only threat with own communication abilities) are low or missing on these lists. The paper discuss the research on malware network activity, aimed to deliver the answer to the question, what is the main infection channel of modern malware, done with the usage of virtual honeypot systems on dedicated, unprotected network. Systems setup, network and systems monitoring solutions, results of over three months of network traffic and malware monitoring are presented, along with the proposed answer to our research question.

Phytoplankton Monitoring Network (PMN)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Phytoplankton Monitoring Network (PMN) is a part of the National Centers for Coastal Ocean Science (NCCOS). The PMN was created as an outreach program to connect...

Reassessment and expansion, 1981-1991

Science.gov (United States)

Grey, J.

In this, the fourth and final decade under consideration for the special issue of Acta Astronautica, an overview of the 10-year span is given rather than a congress-by-congress summary as was appropriate for the opening decades of the federation's existence. The decade was characterized by debate over the frequency of congresses, reassessment of committee structure, improved relations with COSPAR, increasing membership and administrative changes. The ten International Astronautical congresses held during the final decade of this history are listed below noting their sequential numbers, the cities and years in which they took place and their themes: XXXII—Rome, 1981: Space: Mankind's Fourth Environment XXXIII—Paris, 1982: Space 2000 XXXIV—Budapest, 1983: Cooperation in Space XXXV—Lausanne, 1984: Space Benefits for All Nations XXXVI—Stockholm, 1985: Peaceful Space and Global Problems of Mankind XXXVII—Innsbruck, 1986: Space: New Opportunities for All People XXXVIII—Brighton, 1987: Thirty years of Progress in Space XXXIX—Bangalore, 1988: Space and Humanity XL—Malaga-Torremolinos, 1989: The Next Forty Years in Space XLI—Dresden, 1990: Space for Peace and Progress

Radioecology of the Tejo river, 1981-1989

International Nuclear Information System (INIS)

Carreiro, M.C.V.; Bettencourt, A.O.; Sequeira, M.M.A.

1991-01-01

The survey of the natural and artificial radioactivity of the Tejo river has been carried out since 1975; although there are no nuclear power plants in the Portuguese sector of the river, they do exist upstream, in Spain. A radioecological study of the river was also accomplished between the middle of 1986 and the end of 1989 (contract (CEC) Bl6-B-198-P). A brief outline of the main characteristics of the river water, sediments, and biological material, is given in the present paper and the data on the artificial radioactivity survey from 1981 to 1989 are analysed. An increase of the radioactivity in water was detected during the years 1987 and 1989 and in sediments, hydrophytes and fish during 1988; an attempt of explanation is done. Data appear to confirm that sediments are the best compartment to detect 137 Cs contamination in the river [fr

Low Cost Wireless Sensor Network for Continuous Bridge monitoring

DEFF Research Database (Denmark)

Han, Bo; Kalis, A; Tragas, P

2012-01-01

Continuous monitoring wireless sensor networks (WSN) are considered as one of the most promising means to harvest information from large structures in order to assist in structural health monitoring and management. At the same time, continuous monitoring WSNs suffer from limited network lifetimes...

Francis Bitter National Magnet Laboratory. Annual Report, July 1985-June 1986

International Nuclear Information System (INIS)

1986-01-01

Contents include: reports on laboratory research programs--(quantum optics, magnetism, condensed matter chemistry, superconductivity, magnetic separation, magnetic fields of the brain, molecular biophysics, solid-state nuclear magnetic resonance, magnet technology, instrumentation for high-magnetic-field research); reports of visiting scientists-- (reports of users of the high-magnetic-field facility, reports of users of the pulsed-field facility, reports of users of the squid magnetometer and Moessbauer facility); appendices: (publications and meeting speeches, organization, summary of high-field magnet facility use January 1, 1981 through December 31, 1985, July 1, 1985 through June 30, 1986, geographic distribution of high-field magnet users (excluding laboratory staff), summary of educational activities); author index

Occupational radiation exposure at commercial nuclear power reactors, 1981. Annual report

International Nuclear Information System (INIS)

Brooks, B.G.

1982-11-01

This report presents an updated compilation of occupational radiation exposures at commercial nuclear power reactors for the years 1969 through 1981. This year's report contains data received from the 70 light water cooled reactors (LWRs) and one high temperature gas cooled reactor that had been declared to be in commercial operation for at least one full year as of December 31, 1981. This represents an increase of two reactors over the number contained in last year's report. The total number of personnel monitored at LWRs in 1981 was 124,504, a slight decrease from that found in 1980. The number of workers that received measurable doses during 1981 was 82,183 which is about 2000 more than that found in 1980. The total collective dose at LWRs for 1981 is estimated to be 54,142 man-rems, which is only about 350 man-rems more than that reported in 1980. The report also presents a summary and some analyses of the exposure data contained in the termination reports that have been submitted by nuclear power licensees to the Commission pursuant to 10 CFR Section 20.408. As of December 31, 1981, personal identification and exposure information had been collected and computerized for some 210,000 of these terminating reactor personnel

COMBINED AND STORM SEWER NETWORK MONITORING

Directory of Open Access Journals (Sweden)

Justyna Synowiecka

2014-10-01

Full Text Available Monitoring of the drainage networks is an extremely important tool used to understand the phenomena occurring in them. In an era of urbanization and increased run-off, at the expense of natural retention in the catchment, it helps to minimize the risk of local flooding and pollution. In its scope includes measurement of the amount of rainfall, with the use of rain gauges, and their measure in the sewer network, in matter of flows and channel filling, with the help of flow meters. An indispensable part in this step is their proper calibration calibration. In addition to ongoing monitoring of the sewer system, periodic inspections by the qualified employees of Water and Sewage Company should be done. The following article reviews measurement devices, their calibration methods, as well as the phenomena that occur during operation in the sewer network. It provides a solution for monitoring and control based on the experience of the Municipal Water and Sewage Company in Wroclaw, describing common operational problems, their causes, prevention methods and a network operation walkthrough with the improve of performance indicators KPI (Key Performance Indicators according the ECB (European Benchmarking Co-operation.

On-line plant-wide monitoring using neural networks

International Nuclear Information System (INIS)

Turkcan, E.; Ciftcioglu, O.; Eryurek, E.; Upadhyaya, B.R.

1992-06-01

The on-line signal analysis system designed for a multi-level mode operation using neural networks is described. The system is capable of monitoring the plant states by tracking different number of signals up to 32 simultaneously. The data used for this study were acquired from the Borssele Nuclear Power Plant (PWR type), and using the on-line monitoring system. An on-line plant-wide monitoring study using a multilayer neural network model is discussed in this paper. The back-propagation neural network algorithm is used for training the network. The technique assumes that each physical state of the power plant can be represented by a unique pattern of instrument readings which can be related to the condition of the plant. When disturbance occurs, the sensor readings undergo a transient, and form a different set of patterns which represent the new operational status. Diagnosing these patterns can be helpful in identifying this new state of the power plant. To this end, plant-wide monitoring with neutral networks is one of the new techniques in real-time applications. (author). 9 refs.; 5 figs

Wireless Sensor Networks for Long Distance Pipeline Monitoring

OpenAIRE

Augustine C. Azubogu; Victor E. Idigo; Schola U. Nnebe; Obinna S. Oguejiofor; Simon E.

2013-01-01

The main goal of this seminal paper is to introduce the application of Wireless Sensor Networks (WSN) in long distance infrastructure monitoring (in particular in pipeline infrastructure monitoring) – one of the on-going research projects by the Wireless Communication Research Group at the department of Electronic and Computer Engineering, Nnamdi Azikiwe University, Awka. The current sensor network architectures for monitoring long distance pipeline infrastructures are pr...

Network protection and insulation monitoring. Schutztechnik mit Isolationsueberwachung

Energy Technology Data Exchange (ETDEWEB)

Hofheinz, W

1983-01-01

With the increasing use of unearthed power supply networks, the selection of suitable monitoring systems has become increasingly important. By combining the unearthed power supply networks with insulation monitoring, one arrives at a protective technique with high reliability, fireproofness and accident protection. The book describes this type of network and its applications, e.g. for medical purposes. Technologies in West Germany and the USA are compared, and a historical outline is given of protective wire systems and their applications. Methods of measurement employed in insulation monitoring systems are described, and the relevant VDE regulations are cited.

Distributed Interplanetary Delay/Disruption Tolerant Network (DTN) Monitor and Control System

Science.gov (United States)

Wang, Shin-Ywan

2012-01-01

The main purpose of Distributed interplanetary Delay Tolerant Network Monitor and Control System as a DTN system network management implementation in JPL is defined to provide methods and tools that can monitor the DTN operation status, detect and resolve DTN operation failures in some automated style while either space network or some heterogeneous network is infused with DTN capability. In this paper, "DTN Monitor and Control system in Deep Space Network (DSN)" exemplifies a case how DTN Monitor and Control system can be adapted into a space network as it is DTN enabled.

EMMNet: Sensor Networking for Electricity Meter Monitoring

Directory of Open Access Journals (Sweden)

Zhi-Ting Lin

2010-06-01

Full Text Available Smart sensors are emerging as a promising technology for a large number of application domains. This paper presents a collection of requirements and guidelines that serve as a basis for a general smart sensor architecture to monitor electricity meters. It also presents an electricity meter monitoring network, named EMMNet, comprised of data collectors, data concentrators, hand-held devices, a centralized server, and clients. EMMNet provides long-distance communication capabilities, which make it suitable suitable for complex urban environments. In addition, the operational cost of EMMNet is low, compared with other existing remote meter monitoring systems based on GPRS. A new dynamic tree protocol based on the application requirements which can significantly improve the reliability of the network is also proposed. We are currently conducting tests on five networks and investigating network problems for further improvements. Evaluation results indicate that EMMNet enhances the efficiency and accuracy in the reading, recording, and calibration of electricity meters.

EMMNet: sensor networking for electricity meter monitoring.

Science.gov (United States)

Lin, Zhi-Ting; Zheng, Jie; Ji, Yu-Sheng; Zhao, Bao-Hua; Qu, Yu-Gui; Huang, Xu-Dong; Jiang, Xiu-Fang

2010-01-01

Smart sensors are emerging as a promising technology for a large number of application domains. This paper presents a collection of requirements and guidelines that serve as a basis for a general smart sensor architecture to monitor electricity meters. It also presents an electricity meter monitoring network, named EMMNet, comprised of data collectors, data concentrators, hand-held devices, a centralized server, and clients. EMMNet provides long-distance communication capabilities, which make it suitable suitable for complex urban environments. In addition, the operational cost of EMMNet is low, compared with other existing remote meter monitoring systems based on GPRS. A new dynamic tree protocol based on the application requirements which can significantly improve the reliability of the network is also proposed. We are currently conducting tests on five networks and investigating network problems for further improvements. Evaluation results indicate that EMMNet enhances the efficiency and accuracy in the reading, recording, and calibration of electricity meters.

Proceedings of the Strategic Computing Natural Language Workshop Held in Marina del Rey, California on 1-2 May 1986.

Science.gov (United States)

1986-05-01

language interface to these new capabilities as well as to the existing data bases and graphic display facilities. BBN is developing a series of...Action. Artificial Intelligence , 1986. Forthcoming. [Hinrichs 81] Hinrichs, E. Temporale Anaphora um Englischen. 1981. Unpublished ms., University of...organized by NIKL has been demonstrated for a wide variety of sentence types. Table 3 shows a series of independent sentences that Penman is now able

CLC2000 land cover database of the Netherlands; monitoring land cover changes between 1986 and 2000

OpenAIRE

Hazeu, G.W.

2003-01-01

The 1986 CORINE land cover database of the Netherlands was revised and updated on basis of Landsat satellite images and ancillary data. Interpretation of satellite images from 1986 and 2000 resulted in the CLC2000, CLC1986rev and CLCchange databases. A standard European legend and production methodology was applied. Thirty land cover classes were discerned. Most extended land cover types were pastures (231), arable land (211) and complex cultivation patterns (242). Between 1986 and 2000 aroun...

Clustering and Flow Conservation Monitoring Tool for Software Defined Networks

Directory of Open Access Journals (Sweden)

Jesús Antonio Puente Fernández

2018-04-01

Full Text Available Prediction systems present some challenges on two fronts: the relation between video quality and observed session features and on the other hand, dynamics changes on the video quality. Software Defined Networks (SDN is a new concept of network architecture that provides the separation of control plane (controller and data plane (switches in network devices. Due to the existence of the southbound interface, it is possible to deploy monitoring tools to obtain the network status and retrieve a statistics collection. Therefore, achieving the most accurate statistics depends on a strategy of monitoring and information requests of network devices. In this paper, we propose an enhanced algorithm for requesting statistics to measure the traffic flow in SDN networks. Such an algorithm is based on grouping network switches in clusters focusing on their number of ports to apply different monitoring techniques. Such grouping occurs by avoiding monitoring queries in network switches with common characteristics and then, by omitting redundant information. In this way, the present proposal decreases the number of monitoring queries to switches, improving the network traffic and preventing the switching overload. We have tested our optimization in a video streaming simulation using different types of videos. The experiments and comparison with traditional monitoring techniques demonstrate the feasibility of our proposal maintaining similar values decreasing the number of queries to the switches.

Clustering and Flow Conservation Monitoring Tool for Software Defined Networks.

Science.gov (United States)

Puente Fernández, Jesús Antonio; García Villalba, Luis Javier; Kim, Tai-Hoon

2018-04-03

Prediction systems present some challenges on two fronts: the relation between video quality and observed session features and on the other hand, dynamics changes on the video quality. Software Defined Networks (SDN) is a new concept of network architecture that provides the separation of control plane (controller) and data plane (switches) in network devices. Due to the existence of the southbound interface, it is possible to deploy monitoring tools to obtain the network status and retrieve a statistics collection. Therefore, achieving the most accurate statistics depends on a strategy of monitoring and information requests of network devices. In this paper, we propose an enhanced algorithm for requesting statistics to measure the traffic flow in SDN networks. Such an algorithm is based on grouping network switches in clusters focusing on their number of ports to apply different monitoring techniques. Such grouping occurs by avoiding monitoring queries in network switches with common characteristics and then, by omitting redundant information. In this way, the present proposal decreases the number of monitoring queries to switches, improving the network traffic and preventing the switching overload. We have tested our optimization in a video streaming simulation using different types of videos. The experiments and comparison with traditional monitoring techniques demonstrate the feasibility of our proposal maintaining similar values decreasing the number of queries to the switches.

Network monitoring in the Tier2 site in Prague

International Nuclear Information System (INIS)

Eliáš, Marek; Fiala, Lukáš; Horký, Jirí; Chudoba, Jirí; Kouba, Tomáš; Kundrát, Jan; Švec, Jan

2011-01-01

Network monitoring provides different types of view on the network traffic. It's output enables computing centre staff to make qualified decisions about changes in the organization of computing centre network and to spot possible problems. In this paper we present network monitoring framework used at Tier-2 in Prague in Institute of Physics (FZU). The framework consists of standard software and custom tools. We discuss our system for hardware failures detection using syslog logging and Nagios active checks, bandwidth monitoring of physical links and analysis of NetFlow exports from Cisco routers. We present tool for automatic detection of network layout based on SNMP. This tool also records topology changes into SVN repository. Adapted weathermap4rrd is used to visualize recorded data to get fast overview showing current bandwidth usage of links in network.

CLC2000 land cover database of the Netherlands; monitoring land cover changes between 1986 and 2000

NARCIS (Netherlands)

Hazeu, G.W.

2003-01-01

The 1986 CORINE land cover database of the Netherlands was revised and updated on basis of Landsat satellite images and ancillary data. Interpretation of satellite images from 1986 and 2000 resulted in the CLC2000, CLC1986rev and CLCchange databases. A standard European legend and production

CSIR Annual report 1981

CSIR Research Space (South Africa)

CSIR

1981-01-01

Full Text Available This report presents the thirty seventh annual report of the CSIR. The report covers the period 1 January, 1981 to 31 December 1981. A balance sheet and statements of income and expenditure for the financial year ended 31st March 1981, certified...

International energy indicators, October-November 1981

Science.gov (United States)

Rossi, E., Jr.

Detailed data are presented for energy indicators in tables and graphs. Specific international data are presented: world crude oil production, 1974 to July 1981; OPEC crude oil productive capacity; world crude oil and refined product inventory levels, 1975 through the first half of 1981; oil consumption in OFCD countries, 1975 through the first half of 1981; USSR crude oil production, 1975 through July 1981; and free world and US nuclear electricity generation, 1973 through September 1981 and current capacity. Data presented for energy indicators in the US are: US domestic oil supply and crude oil production, 1977 through March 1981; US gross imports of crude oil and products, 1973 through August 1981; landed cost of Saudi crude oil in current and 1974 dollars; US coal trade, 1975 through July 1981; US natural gas trade, 1975 through August 1981; summary of US merchandise trade, 1977 through the first half of 1981; and the energy/gross national product ratio from 1974 through the first half of 1981.

SURFmap: A Network Monitoring Tool Based on the Google Maps API

NARCIS (Netherlands)

Hofstede, R.J.; Hofstede, R. J.; Fioreze, Tiago

2009-01-01

Network monitoring allows network managers to get a better insight in the network traffic transiting in a managed network. In order to make the tasks of a network manager easier, many network monitoring tools are made available for a wide range of purposes (e.g., traffic accounting, performance

Assessment of SRS ambient air monitoring network

Energy Technology Data Exchange (ETDEWEB)

Abbott, K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Jannik, T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-08-03

Three methodologies have been used to assess the effectiveness of the existing ambient air monitoring system in place at the Savannah River Site in Aiken, SC. Effectiveness was measured using two metrics that have been utilized in previous quantification of air-monitoring network performance; frequency of detection (a measurement of how frequently a minimum number of samplers within the network detect an event), and network intensity (a measurement of how consistent each sampler within the network is at detecting events). In addition to determining the effectiveness of the current system, the objective of performing this assessment was to determine what, if any, changes could make the system more effective. Methodologies included 1) the Waite method of determining sampler distribution, 2) the CAP88- PC annual dose model, and 3) a puff/plume transport model used to predict air concentrations at sampler locations. Data collected from air samplers at SRS in 2015 compared with predicted data resulting from the methodologies determined that the frequency of detection for the current system is 79.2% with sampler efficiencies ranging from 5% to 45%, and a mean network intensity of 21.5%. One of the air monitoring stations had an efficiency of less than 10%, and detected releases during just one sampling period of the entire year, adding little to the overall network intensity. By moving or removing this sampler, the mean network intensity increased to about 23%. Further work in increasing the network intensity and simulating accident scenarios to further test the ambient air system at SRS is planned

Optical Network Virtualisation Using Multitechnology Monitoring and SDN-Enabled Optical Transceiver

Science.gov (United States)

Ou, Yanni; Davis, Matthew; Aguado, Alejandro; Meng, Fanchao; Nejabati, Reza; Simeonidou, Dimitra

2018-05-01

We introduce the real-time multi-technology transport layer monitoring to facilitate the coordinated virtualisation of optical and Ethernet networks supported by optical virtualise-able transceivers (V-BVT). A monitoring and network resource configuration scheme is proposed to include the hardware monitoring in both Ethernet and Optical layers. The scheme depicts the data and control interactions among multiple network layers under the software defined network (SDN) background, as well as the application that analyses the monitored data obtained from the database. We also present a re-configuration algorithm to adaptively modify the composition of virtual optical networks based on two criteria. The proposed monitoring scheme is experimentally demonstrated with OpenFlow (OF) extensions for a holistic (re-)configuration across both layers in Ethernet switches and V-BVTs.

Vibration monitoring with artificial neural networks

International Nuclear Information System (INIS)

Alguindigue, I.

1991-01-01

Vibration monitoring of components in nuclear power plants has been used for a number of years. This technique involves the analysis of vibration data coming from vital components of the plant to detect features which reflect the operational state of machinery. The analysis leads to the identification of potential failures and their causes, and makes it possible to perform efficient preventive maintenance. Earlydetection is important because it can decrease the probability of catastrophic failures, reduce forced outgage, maximize utilization of available assets, increase the life of the plant, and reduce maintenance costs. This paper documents our work on the design of a vibration monitoring methodology based on neural network technology. This technology provides an attractive complement to traditional vibration analysis because of the potential of neural network to operate in real-time mode and to handle data which may be distorted or noisy. Our efforts have been concentrated on the analysis and classification of vibration signatures collected from operating machinery. Two neural networks algorithms were used in our project: the Recirculation algorithm for data compression and the Backpropagation algorithm to perform the actual classification of the patterns. Although this project is in the early stages of development it indicates that neural networks may provide a viable methodology for monitoring and diagnostics of vibrating components. Our results to date are very encouraging

NRC TLD Direct Radiation Monitoring Network

International Nuclear Information System (INIS)

Struckmeyer, R.; McNamara, N.

1992-06-01

The US Nuclear Regulatory Commission (NRC) Direct Radiation Monitoring Network is operated by the NRC in cooperation with participating states to provide continuous measurement of the ambient radiation levels around licensed NRC facilities, primarily power reactors. Ambient radiation levels result from naturally occurring radionuclides present in the soil, cosmic radiation constantly bombarding the earth from outer space, and the contribution, if any, from the monitored facilities and other man-made sources. The Network is intended to measure radiation levels during routine facility operations and to establish background radiation levels used to assess the radiological impact of an unusual condition, such as an accident. This report presents the radiation levels measured around all facilities in the Network for the first quarter of 1992. All radiation measurements are made using small, passive detectors called thermoluminescent dosimeters (TLDs), which provide a quantitative measurement of the radiation levels in the area in which they are placed. Each site is monitored by arranging approximately 40 to 50 TLD stations in two concentric rings extending to about five miles from the facility. All TLD stations are outside the site boundary of the facility

Biological and Medical Experiments on the Space Shuttle, 1981 - 1985

Science.gov (United States)

Halstead, Thora W. (Editor); Dufour, Patricia A. (Editor)

1986-01-01

This volume is the first in a planned series of reports intended to provide a comprehensive record of all the biological and medical experiments and samples flown on the Space Shuttle. Experiments described have been conducted over a five-year period, beginning with the first plant studies conducted on STS-2 in November 1981, and extending through STS 61-C, the last mission to fly before the tragic Challenger accident of January 1986. Experiments were sponsored within NASA not only by the Life Sciences Division of the Office of Space Science and Applications, but also by the Shuttle Student Involvement Program (SSIP) and the Get Away Special (GAS) Program. Independent medical studies were conducted as well on the Shuttle crew under the auspices of the Space Biomedical Research Institute at Johnson Space Center. In addition, cooperative agreements between NASA and foreign government agencies led to a number of independent experiments and also paved the way for the joint US/ESA Spacelab 1 mission and the German (DFVLR) Spacelab D-1. Experiments included: (1) medically oriented studies of the crew aimed at identifying, preventing, or treating health problems due to space travel; (2) projects to study morphological, physiological, or behavioral effects of microgravity on animals and plants; (3) studies of the effects of microgravity on cells and tissues; and (4) radiation experiments monitoring the spacecraft environment with chemical or biological dosimeters or testing radiation effects on simple organisms and seeds.

The water-quality monitoring program for the Baltimore reservoir system, 1981-2007—Description, review and evaluation, and framework integration for enhanced monitoring

Science.gov (United States)

Koterba, Michael T.; Waldron, Marcus C.; Kraus, Tamara E.C.

2011-01-01

The City of Baltimore, Maryland, and parts of five surrounding counties obtain their water from Loch Raven and Liberty Reservoirs. A third reservoir, Prettyboy, is used to resupply Loch Raven Reservoir. Management of the watershed conditions for each reservoir is a shared responsibility by agreement among City, County, and State jurisdictions. The most recent (2005) Baltimore Reservoir Watershed Management Agreement (RWMA) called for continued and improved water-quality monitoring in the reservoirs and selected watershed tributaries. The U.S. Geological Survey (USGS) conducted a retrospective review of the effectiveness of monitoring data obtained and analyzed by the RWMA jurisdictions from 1981 through 2007 to help identify possible improvements in the monitoring program to address RWMA water-quality concerns. Long-term water-quality concerns include eutrophication and sedimentation in the reservoirs, and elevated concentrations of (a) nutrients (nitrogen and phosphorus) being transported from the major tributaries to the reservoirs, (b) iron and manganese released from reservoir bed sediments during periods of deep-water anoxia, (c) mercury in higher trophic order game fish in the reservoirs, and (d) bacteria in selected reservoir watershed tributaries. Emerging concerns include elevated concentrations of sodium, chloride, and disinfection by-products (DBPs) in the drinking water from both supply reservoirs. Climate change and variability also could be emerging concerns, affecting seasonal patterns, annual trends, and drought occurrence, which historically have led to declines in reservoir water quality. Monitoring data increasingly have been used to support the development of water-quality models. The most recent (2006) modeling helped establish an annual sediment Total Maximum Daily Load to Loch Raven Reservoir, and instantaneous and 30-day moving average water-quality endpoints for chlorophyll-a (chl-a) and dissolved oxygen (DO) in Loch Raven and Prettyboy

Analysis and monitoring design for networks

Energy Technology Data Exchange (ETDEWEB)

Fedorov, V.; Flanagan, D.; Rowan, T.; Batsell, S.

1998-06-01

The idea of applying experimental design methodologies to develop monitoring systems for computer networks is relatively novel even though it was applied in other areas such as meteorology, seismology, and transportation. One objective of a monitoring system should always be to collect as little data as necessary to be able to monitor specific parameters of the system with respect to assigned targets and objectives. This implies a purposeful monitoring where each piece of data has a reason to be collected and stored for future use. When a computer network system as large and complex as the Internet is the monitoring subject, providing an optimal and parsimonious observing system becomes even more important. Many data collection decisions must be made by the developers of a monitoring system. These decisions include but are not limited to the following: (1) The type data collection hardware and software instruments to be used; (2) How to minimize interruption of regular network activities during data collection; (3) Quantification of the objectives and the formulation of optimality criteria; (4) The placement of data collection hardware and software devices; (5) The amount of data to be collected in a given time period, how large a subset of the available data to collect during the period, the length of the period, and the frequency of data collection; (6) The determination of the data to be collected (for instance, selection of response and explanatory variables); (7) Which data will be retained and how long (i.e., data storage and retention issues); and (8) The cost analysis of experiments. Mathematical statistics, and, in particular, optimal experimental design methods, may be used to address the majority of problems generated by 3--7. In this study, the authors focus their efforts on topics 3--5.

Radiation monitoring network of the Slovak Hydrometeorological Institute

International Nuclear Information System (INIS)

Melicherova, T.

2005-01-01

In 2000 Centre of Partial monitoring system 'Radioactivity of environment' was established on Slovak Hydrometeorology Institute (SHMI). Radiation monitoring network is one part of Radiation monitoring network of the Slovak Republic. At present SHMI operates in its monitoring network 23 detectors GammaTracer fy Genitron, one mobile detector and one stan by detector. All active detectors are placed in the professional meteorological stations in the selected parts of Slovakia. First one of these detectors was installed in 1999 and they replaced former type of detector (FAG). Last two detectors were installed in 2002. Detector GammaTracer has range of measurement from 20 nSv/h to 10 Sv/h. The detectors are calibrated every 2 years in the Slovak Institute of Metrology in compliance with the calibration plan. SHMI operates 4 aerosol monitors in Hurbanovo, Lucenec, Stropkov and Liesek. Filter 8 from these monitors are analysed in the Institute of Public Health (Cs-137, Be-7). On the base of bilateral agreement between the Austrian Ministry of Agriculture, Forestry, Environment and Water-Management and the Slovak Ministry of Environment Austrian side gave into the ownership of the Slovak side an automatic aerosol monitor AMS-02 including container and weather station. This monitor was installed in meteorological station Jaslovske Bohunice on 4-th October 2001. The Slovak Ministry of Environment provides the Austrian Ministry of Agriculture, Forestry, Environment and Water-Management with the readings of this monitor, free of charge, for at least 3 years and vice versa, the Austrian side gives the readings of the Austrian aerosol monitors to the Slovak Ministry of Environment free of charge. At present national monitoring center in Bratislava-Koliba is connected via ISDN line with Jaslovske Bohunice and Austrian center providing the data exchange. Radiation data (dose rate in the unit nSv/h) are collected via the Institute network to the MSS (message switch system) in the

Environmental monitoring networks in Spain; Redes de vigilancia radiologica ambiental en Espana

Energy Technology Data Exchange (ETDEWEB)

Luque Heredia, S.; Martin Matarranz, J. L.; Marugan Tovar, I.; Rey del Castillo, C.; Salas Collantes, R.; Sterling Carmona, A.; Ramos Salvador, L. M.

2011-07-01

Environmental monitoring in Spain is carried out by several networks with different objectives and scope, a monitoring network in the vicinity of nuclear facilities and radioactive nuclear fuel cycle and various monitoring networks nationally funded and managed by agencies public. The aim of this paper is to present a summary of all monitoring networks, including a series of figures with the stations that are, their geographical distribution and the programs in them.

Environmental surveillance at Los Alamos during 1981

International Nuclear Information System (INIS)

1982-04-01

This report documents the environmental surveillance program conducted by the Los Alamos National Laboratory during 1981. Routine monitoring for radiation and radioactive or chemical substances is conducted on the Laboratory site and in the surrounding region to determine compliance with appropriate standards and permit early identification of possible undesirable trends. Results and interpretation of data for 1981 are included on penetrating radiation; on the chemical and radiochemical quality of ambient air, surface and ground water, municipal water supply, soil and sediments, and food; and on the quantities of airborne emissions and liquid effluents. Comparisons with appropriate standards and regulations or with background levels from natural or other non-Laboratory sources provide a basis for concluding that environmental effects attributable to Laboratory operations are insignificant and are not considered hazardous to the population of the area. Results of several special studies describe some unique environmental conditions in the Laboratory environs

ANZA Seismic Network- From Monitoring to Science

Science.gov (United States)

Vernon, F.; Eakin, J.; Martynov, V.; Newman, R.; Offield, G.; Hindley, A.; Astiz, L.

2007-05-01

The ANZA Seismic Network (http:eqinfo.ucsd.edu) utilizes broadband and strong motion sensors with 24-bit dataloggers combined with real-time telemetry to monitor local and regional seismicity in southernmost California. The ANZA network provides real-time data to the IRIS DMC, California Integrated Seismic Network (CISN), other regional networks, and the Advanced National Seismic System (ANSS), in addition to providing near real-time information and monitoring to the greater San Diego community. Twelve high dynamic range broadband and strong motion sensors adjacent to the San Jacinto Fault zone contribute data for earthquake source studies and continue the monitoring of the seismic activity of the San Jacinto fault initiated 24 years ago. Five additional stations are located in the San Diego region with one more station on San Clemente Island. The ANZA network uses the advance wireless networking capabilities of the NSF High Performance Wireless Research and Education Network (http:hpwren.ucsd.edu) to provide the communication infrastructure for the real-time telemetry of Anza seismic stations. The ANZA network uses the Antelope data acquisition software. The combination of high quality hardware, communications, and software allow for an annual network uptime in excess of 99.5% with a median annual station real-time data return rate of 99.3%. Approximately 90,000 events, dominantly local sources but including regional and teleseismic events, comprise the ANZA network waveform database. All waveform data and event data are managed using the Datascope relational database. The ANZA network data has been used in a variety of scientific research including detailed structure of the San Jacinto Fault Zone, earthquake source physics, spatial and temporal studies of aftershocks, array studies of teleseismic body waves, and array studies on the source of microseisms. To augment the location, detection, and high frequency observations of the seismic source spectrum from local

Design of a particulate-monitoring network for the Y-12 plant

International Nuclear Information System (INIS)

Hougland, E.S.; Oakes, T.W.; Underwood, J.N.

1982-01-01

An Air Quality Monitoring Network Design (AQMND) with multiple objectives is being developed for the Y-12 Plant production facilities. The objectives are: Y-12 facility surveillance; monitoring the transport of Y-12 generated airborne effluents towards either the Oak Ridge National Laboratory or the developed region of the City of Oak Ridge; and monitoring population exposure in residential areas close to the Y-12 Plant. A two step design process was carried out, using the Air Quality Monitor Network Design Model (AQMND) previously used for the Oak Ridge National Laboratory network. In the first step of the design we used existing air quality monitor locations, subjectively designated locations, and grid intersections as a set of potential monitor sites. The priority sites from the first step (modified to account for terrain and accessibility), and subjectively designated sites, were used as the potential monitor sites for the second step of the process which produced the final design recommendations for the monitor network

Icinga network monitoring

CERN Document Server

Mehta, Viranch

2013-01-01

This book is written in a concise and easy-to-follow approach, it will guide you to get you started with Icinga and lead you through the difficult concepts with illustrated examples and screenshots.If you are a system administrator or Linux enthusiast who is looking for a flexible tool to monitor network infrastructure efficiently, or trying to understand the Icinga software, this is a great book for you. You are expected to have solid foundation in Linux.

A study of reactor monitoring method with neural network

Energy Technology Data Exchange (ETDEWEB)

Nabeshima, Kunihiko [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2001-03-01

The purpose of this study is to investigate the methodology of Nuclear Power Plant (NPP) monitoring with neural networks, which create the plant models by the learning of the past normal operation patterns. The concept of this method is to detect the symptom of small anomalies by monitoring the deviations between the process signals measured from an actual plant and corresponding output signals from the neural network model, which might not be equal if the abnormal operational patterns are presented to the input of the neural network. Auto-associative network, which has same output as inputs, can detect an kind of anomaly condition by using normal operation data only. The monitoring tests of the feedforward neural network with adaptive learning were performed using the PWR plant simulator by which many kinds of anomaly conditions can be easily simulated. The adaptively trained feedforward network could follow the actual plant dynamics and the changes of plant condition, and then find most of the anomalies much earlier than the conventional alarm system during steady state and transient operations. Then the off-line and on-line test results during one year operation at the actual NPP (PWR) showed that the neural network could detect several small anomalies which the operators or the conventional alarm system didn't noticed. Furthermore, the sensitivity analysis suggests that the plant models by neural networks are appropriate. Finally, the simulation results show that the recurrent neural network with feedback connections could successfully model the slow behavior of the reactor dynamics without adaptive learning. Therefore, the recurrent neural network with adaptive learning will be the best choice for the actual reactor monitoring system. (author)

Optical Performance Monitoring and Signal Optimization in Optical Networks

DEFF Research Database (Denmark)

Petersen, Martin Nordal

2006-01-01

The thesis studies performance monitoring for the next generation optical networks. The focus is on all-optical networks with bit-rates of 10 Gb/s or above. Next generation all-optical networks offer large challenges as the optical transmitted distance increases and the occurrence of electrical-optical......-electrical regeneration points decreases. This thesis evaluates the impact of signal degrading effects that are becoming of increasing concern in all-optical high-speed networks due to all-optical switching and higher bit-rates. Especially group-velocity-dispersion (GVD) and a number of nonlinear effects will require...... enhanced attention to avoid signal degradations. The requirements for optical performance monitoring features are discussed, and the thesis evaluates the advantages and necessity of increasing the level of performance monitoring parameters in the physical layer. In particular, methods for optical...

A wireless sensor network design and evaluation for large structural strain field monitoring

International Nuclear Information System (INIS)

Qiu, Zixue; Wu, Jian; Yuan, Shenfang

2011-01-01

Structural strain changes under external environmental or mechanical loads are the main monitoring parameters in structural health monitoring or mechanical property tests. This paper presents a wireless sensor network designed for monitoring large structural strain field variation. First of all, a precision strain sensor node is designed for multi-channel strain gauge signal conditioning and wireless monitoring. In order to establish a synchronous strain data acquisition network, the cluster-star network synchronization method is designed in detail. To verify the functionality of the designed wireless network for strain field monitoring capability, a multi-point network evaluation system is developed for an experimental aluminum plate structure for load variation monitoring. Based on the precision wireless strain nodes, the wireless data acquisition network is deployed to synchronously gather, process and transmit strain gauge signals and monitor results under concentrated loads. This paper shows the efficiency of the wireless sensor network for large structural strain field monitoring

RadNet Radiological Air Monitoring Network

International Nuclear Information System (INIS)

Scott Telofski, J.; Askren, D.R.; Petko, Ch.M.; Fraass, R.G.

2010-01-01

The United States Environmental Protection Agency operates a national environmental radiation monitoring program called RadNet. RadNet monitors airborne particulates, precipitation, milk, and drinking water for radiation levels. The primary purpose of the original program in the 1950's and 1960's was to collect and analyze samples in various media to assess the effects of radioactive fallout from above-ground nuclear weapon testing. As above-ground testing diminished in the 1970's, the program, especially the air network, became critical in evaluating effects of other types of nuclear incidents, such as the nuclear reactor accident at Chernobyl, as well as monitoring trends in environmental radioactive contamination. The value of rapid data collection subsequent to such incidents led to the consideration of developing air monitors with radiation detectors and telecommunication equipment for real-time radiation measurement. The strengthened United States homeland security posture after 2001 led to production and installation of the current real-time RadNet air monitors. There are now 118 stationary, continuously operating air monitoring stations and 40 mobile air monitors for site specific monitoring. The stationary air monitors include radiation detectors, meteorological sensors, a high-volume air sampler, and communication devices for hourly data transfers. When unusual levels are detected, scientists download a full sodium iodide detector spectrum for analysis. The real-time data collected by RadNet stationary systems permit rapid identification and quantification of airborne nuclides with sufficient sensitivity to provide critical information to help determine protective actions. The data also may help to rapidly refine long-range radioactive plume models and estimate exposure to the population. This paper provides an overview of the airborne particulate monitoring conducted during above-ground nuclear weapon testing, summarizes the uses of data from the program

Smart Sensor Network System For Environment Monitoring

Directory of Open Access Journals (Sweden)

Javed Ali Baloch

2012-07-01

Full Text Available SSN (Smart Sensor Network systems could be used to monitor buildings with modern infrastructure, plant sites with chemical pollution, horticulture, natural habitat, wastewater management and modern transport system. To sense attributes of phenomena and make decisions on the basis of the sensed value is the primary goal of such systems. In this paper a Smart Spatially aware sensor system is presented. A smart system, which could continuously monitor the network to observe the functionality and trigger, alerts to the base station if a change in the system occurs and provide feedback periodically, on demand or even continuously depending on the nature of the application. The results of the simulation trials presented in this paper exhibit the performance of a Smart Spatially Aware Sensor Networks.

A Wildlife Monitoring System Based on Wireless Image Sensor Networks

Directory of Open Access Journals (Sweden)

Junguo Zhang

2014-10-01

Full Text Available Survival and development of wildlife sustains the balance and stability of the entire ecosystem. Wildlife monitoring can provide lots of information such as wildlife species, quantity, habits, quality of life and habitat conditions, to help researchers grasp the status and dynamics of wildlife resources, and to provide basis for the effective protection, sustainable use, and scientific management of wildlife resources. Wildlife monitoring is the foundation of wildlife protection and management. Wireless Sensor Networks (WSN technology has become the most popular technology in the field of information. With advance of the CMOS image sensor technology, wireless sensor networks combined with image sensors, namely Wireless Image Sensor Networks (WISN technology, has emerged as an alternative in monitoring applications. Monitoring wildlife is one of its most promising applications. In this paper, system architecture of the wildlife monitoring system based on the wireless image sensor networks was presented to overcome the shortcomings of the traditional monitoring methods. Specifically, some key issues including design of wireless image sensor nodes and software process design have been studied and presented. A self-powered rotatable wireless infrared image sensor node based on ARM and an aggregation node designed for large amounts of data were developed. In addition, their corresponding software was designed. The proposed system is able to monitor wildlife accurately, automatically, and remotely in all-weather condition, which lays foundations for applications of wireless image sensor networks in wildlife monitoring.

Applied network security monitoring collection, detection, and analysis

CERN Document Server

Sanders, Chris

2013-01-01

Applied Network Security Monitoring is the essential guide to becoming an NSM analyst from the ground up. This book takes a fundamental approach to NSM, complete with dozens of real-world examples that teach you the key concepts of NSM. Network security monitoring is based on the principle that prevention eventually fails. In the current threat landscape, no matter how much you try, motivated attackers will eventually find their way into your network. At that point, it is your ability to detect and respond to that intrusion that can be the difference between a small incident and a major di

Intercontinental Multi-Domain Monitoring for the LHC Optical Private Network

CERN Multimedia

CERN. Geneva

2012-01-01

The Large Hadron Collider (LHC) is currently running at CERN in Geneva, Switzerland. Physicists are using LHC to recreate the conditions just after the Big Bang, by colliding two beams of particles and heavy ions head-on at very high energy. The project is expected to generate 27 TB of raw data per day, plus 10 TB of "event summary data". This data is sent out from CERN to eleven Tier 1 academic institutions in Europe, Asia, and North America using a multi-gigabits Optical Private Network (OPN), the LHCOPN. Network monitoring on such complex network architecture to ensure robust and reliable operation is of crucial importance. The chosen approach for monitoring the OPN is based on the perfSONAR MDM framework (http://perfsonar.geant.net), which is designed for multi-domain monitoring environments. perfSONAR (www.perfsonar.net) is an infrastructure for performance monitoring data exchange between networks, making it easier to solve performance problems occurring between network measurement points interconne...

Wide area network monitoring system for HEP experiments at Fermilab

International Nuclear Information System (INIS)

Grigoriev, Maxim; Fermilab; Cottrell, Les; Logg, Connie; SLAC

2004-01-01

Large, distributed High Energy Physics (HEP) collaborations, such as D0, CDF and US-CMS, depend on stable and robust network paths between major world research centres. The evolving emphasis on data and compute Grids increases the reliance on network performance. Fermilab's experimental groups and network support personnel identified a critical need for WAN monitoring to ensure the quality and efficient utilization of such network paths. This has led to the development of the Network Monitoring system we will present in this paper. The system evolved from the IEPM-BW project, started at SLAC three years ago. At Fermilab this system has developed into a fully functional infrastructure with bi-directional active network probes and path characterizations. It is based on the Iperf achievable throughput tool, Ping and Synack to test ICMP/TCP connectivity. It uses Pipechar and Traceroute to test, compare and report hop-by-hop network path characterization. It also measures real file transfer performance by BBFTP and GridFTP. The Monitoring system has an extensive web-interface and all the data is available through standalone SOAP web services or by a MonaLISA client. Also in this paper we will present a case study of network path asymmetry and abnormal performance between FNAL and SDSC, which was discovered and resolved by utilizing the Network Monitoring system

Wide Area Network Monitoring System for HEP Experiments at Fermilab

International Nuclear Information System (INIS)

Grigoriev, M.

2004-01-01

Large, distributed High Energy Physics (HEP) collaborations, such as D0, CDF and US-CMS, depend on stable and robust network paths between major world research centres. The evolving emphasis on data and compute Grids increases the reliance on network performance. Fermilab's experimental groups and network support personnel identified a critical need for WAN monitoring to ensure the quality and efficient utilization of such network paths. This has led to the development of the Network Monitoring system we will present in this paper. The system evolved from the IEPM-BW project, started at SLAC three years ago. At Fermilab this system has developed into a fully functional infrastructure with bi-directional active network probes and path characterizations. It is based on the Iperf achievable throughput tool, Ping and Synack to test ICMP/TCP connectivity. It uses Pipechar and Traceroute to test, compare and report hop-by-hop network path characterization. It also measures real file transfer performance by BBFTP and GridFTP. The Monitoring system has an extensive web-interface and all the data is available through standalone SOAP web services or by a MonaLISA client. Also in this paper we will present a case study of network path asymmetry and abnormal performance between FNAL and SDSC, which was discovered and resolved by utilizing the Network Monitoring system

Wide Area Network Monitoring System for HEP Experiments at Fermilab

Energy Technology Data Exchange (ETDEWEB)

Grigoriev, M.

2004-11-23

Large, distributed High Energy Physics (HEP) collaborations, such as D0, CDF and US-CMS, depend on stable and robust network paths between major world research centres. The evolving emphasis on data and compute Grids increases the reliance on network performance. Fermilab's experimental groups and network support personnel identified a critical need for WAN monitoring to ensure the quality and efficient utilization of such network paths. This has led to the development of the Network Monitoring system we will present in this paper. The system evolved from the IEPM-BW project, started at SLAC three years ago. At Fermilab this system has developed into a fully functional infrastructure with bi-directional active network probes and path characterizations. It is based on the Iperf achievable throughput tool, Ping and Synack to test ICMP/TCP connectivity. It uses Pipechar and Traceroute to test, compare and report hop-by-hop network path characterization. It also measures real file transfer performance by BBFTP and GridFTP. The Monitoring system has an extensive web-interface and all the data is available through standalone SOAP web services or by a MonaLISA client. Also in this paper we will present a case study of network path asymmetry and abnormal performance between FNAL and SDSC, which was discovered and resolved by utilizing the Network Monitoring system.

NRC TLD Direct Radiation Monitoring Network

International Nuclear Information System (INIS)

Struckmeyer, R.

1994-03-01

This report presents the results of the NRC Direct Radiation Monitoring Network for the fourth quarter of 1993. It provides the ambient radiation levels measured in the vicinity of 75 sites throughout the United States. In addition, it describes the equipment used, monitoring station selection criteria, characterization of the dosimeter response, calibration procedures, statistical methods, intercomparison, and quality assurance program

NRC TLD Direct Radiation Monitoring Network

International Nuclear Information System (INIS)

Struckmeyer, R.; McNamara, N.

1993-03-01

This report present the results of the NRC Direct Radiation Monitoring Network for the fourth quarter of 1992. It provides the ambient radiation levels measured in the vicinity of 75 sites throughout the United States. In addition, it describes the equipment used, monitoring station selection criteria, characterization of the dosimeter response, calibration procedures, statistical methods, intercomparison, and quality assurance program

Sonification of network traffic flow for monitoring and situational awareness

Science.gov (United States)

2018-01-01

Maintaining situational awareness of what is happening within a computer network is challenging, not only because the behaviour happens within machines, but also because data traffic speeds and volumes are beyond human ability to process. Visualisation techniques are widely used to present information about network traffic dynamics. Although they provide operators with an overall view and specific information about particular traffic or attacks on the network, they often still fail to represent the events in an understandable way. Also, because they require visual attention they are not well suited to continuous monitoring scenarios in which network administrators must carry out other tasks. Here we present SoNSTAR (Sonification of Networks for SiTuational AwaReness), a real-time sonification system for monitoring computer networks to support network administrators’ situational awareness. SoNSTAR provides an auditory representation of all the TCP/IP traffic within a network based on the different traffic flows between between network hosts. A user study showed that SoNSTAR raises situational awareness levels by enabling operators to understand network behaviour and with the benefit of lower workload demands (as measured by the NASA TLX method) than visual techniques. SoNSTAR identifies network traffic features by inspecting the status flags of TCP/IP packet headers. Combinations of these features define particular traffic events which are mapped to recorded sounds to generate a soundscape that represents the real-time status of the network traffic environment. The sequence, timing, and loudness of the different sounds allow the network to be monitored and anomalous behaviour to be detected without the need to continuously watch a monitor screen. PMID:29672543

Sonification of network traffic flow for monitoring and situational awareness.

Science.gov (United States)

Debashi, Mohamed; Vickers, Paul

2018-01-01

Maintaining situational awareness of what is happening within a computer network is challenging, not only because the behaviour happens within machines, but also because data traffic speeds and volumes are beyond human ability to process. Visualisation techniques are widely used to present information about network traffic dynamics. Although they provide operators with an overall view and specific information about particular traffic or attacks on the network, they often still fail to represent the events in an understandable way. Also, because they require visual attention they are not well suited to continuous monitoring scenarios in which network administrators must carry out other tasks. Here we present SoNSTAR (Sonification of Networks for SiTuational AwaReness), a real-time sonification system for monitoring computer networks to support network administrators' situational awareness. SoNSTAR provides an auditory representation of all the TCP/IP traffic within a network based on the different traffic flows between between network hosts. A user study showed that SoNSTAR raises situational awareness levels by enabling operators to understand network behaviour and with the benefit of lower workload demands (as measured by the NASA TLX method) than visual techniques. SoNSTAR identifies network traffic features by inspecting the status flags of TCP/IP packet headers. Combinations of these features define particular traffic events which are mapped to recorded sounds to generate a soundscape that represents the real-time status of the network traffic environment. The sequence, timing, and loudness of the different sounds allow the network to be monitored and anomalous behaviour to be detected without the need to continuously watch a monitor screen.

Modeling Wireless Sensor Networks for Monitoring in Biological Processes

DEFF Research Database (Denmark)

Nadimi, Esmaeil

parameters, as the use of wired sensors is impractical. In this thesis, a ZigBee based wireless sensor network was employed and only a part of the herd was monitored, as monitoring each individual animal in a large herd under practical conditions is inefficient. Investigations to show that the monitored...... (MMAE) approach to the data resulted in the highest classification success rate, due to the use of precise forth-order mathematical models which relate the feed offer to the pitch angle of the neck. This thesis shows that wireless sensor networks can be successfully employed to monitor the behavior...

Connection with seismic networks and construction of real time earthquake monitoring system

Energy Technology Data Exchange (ETDEWEB)

Chi, Heon Cheol; Lee, H. I.; Shin, I. C.; Lim, I. S.; Park, J. H.; Lee, B. K.; Whee, K. H.; Cho, C. S. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

2000-12-15

It is natural to use the nuclear power plant seismic network which have been operated by KEPRI(Korea Electric Power Research Institute) and local seismic network by KIGAM(Korea Institute of Geology, Mining and Material). The real time earthquake monitoring system is composed with monitoring module and data base module. Data base module plays role of seismic data storage and classification and the other, monitoring module represents the status of acceleration in the nuclear power plant area. This research placed the target on the first, networking the KIN's seismic monitoring system with KIGAM and KEPRI seismic network and the second, construction the KIN's Independent earthquake monitoring system.

Connection with seismic networks and construction of real time earthquake monitoring system

International Nuclear Information System (INIS)

Chi, Heon Cheol; Lee, H. I.; Shin, I. C.; Lim, I. S.; Park, J. H.; Lee, B. K.; Whee, K. H.; Cho, C. S.

2000-12-01

It is natural to use the nuclear power plant seismic network which have been operated by KEPRI(Korea Electric Power Research Institute) and local seismic network by KIGAM(Korea Institute of Geology, Mining and Material). The real time earthquake monitoring system is composed with monitoring module and data base module. Data base module plays role of seismic data storage and classification and the other, monitoring module represents the status of acceleration in the nuclear power plant area. This research placed the target on the first, networking the KIN's seismic monitoring system with KIGAM and KEPRI seismic network and the second, construction the KIN's Independent earthquake monitoring system

NRC TLD Direct Radiation Monitoring Network

International Nuclear Information System (INIS)

Struckmeyer, R.; McNamara, N.

1991-04-01

This report presents the results of the NRC [Nuclear Regulatory Commission] Direct Radiation Monitoring Network for the fourth quarter of 1990. It provides the ambient radiation levels measured in the vicinity of 75 sites throughout the United States. In addition, it describes the equipment used, monitoring station selection criteria, characterization of the dosimeter response, calibration procedures, statistical methods, intercomparison, and quality assurance program. 3 figs., 4 tabs

Wireless Sensor Network for Electric Transmission Line Monitoring

Energy Technology Data Exchange (ETDEWEB)

Alphenaar, Bruce

2009-06-30

Generally, federal agencies tasked to oversee power grid reliability are dependent on data from grid infrastructure owners and operators in order to obtain a basic level of situational awareness. Since there are many owners and operators involved in the day-to-day functioning of the power grid, the task of accessing, aggregating and analyzing grid information from these sources is not a trivial one. Seemingly basic tasks such as synchronizing data timestamps between many different data providers and sources can be difficult as evidenced during the post-event analysis of the August 2003 blackout. In this project we investigate the efficacy and cost effectiveness of deploying a network of wireless power line monitoring devices as a method of independently monitoring key parts of the power grid as a complement to the data which is currently available to federal agencies from grid system operators. Such a network is modeled on proprietary power line monitoring technologies and networks invented, developed and deployed by Genscape, a Louisville, Kentucky based real-time energy information provider. Genscape measures transmission line power flow using measurements of electromagnetic fields under overhead high voltage transmission power lines in the United States and Europe. Opportunities for optimization of the commercial power line monitoring technology were investigated in this project to enable lower power consumption, lower cost and improvements to measurement methodologies. These optimizations were performed in order to better enable the use of wireless transmission line monitors in large network deployments (perhaps covering several thousand power lines) for federal situational awareness needs. Power consumption and cost reduction were addressed by developing a power line monitor using a low power, low cost wireless telemetry platform known as the ''Mote''. Motes were first developed as smart sensor nodes in wireless mesh networking applications

Temperature profiles from XBT casts from the MARINE EVANGELINE as part of the Marine Resources Monitoring, Assessment and Prediction (MARMAP) project from 1981-08-25 to 1981-08-26 (NODC Accession 8100678)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profiles were collected from XBT casts from the MARINE EVANGELINE from 25 August 1981 to 26 August 1981. Data were collected by the National Marine...

Thyroid cancer in children and adolescents in Ukraine after the Chernobyl accident (1986-1995)

International Nuclear Information System (INIS)

Tronko, N.; Bogdanova, T.; Komissarenko, I.; Bolshova, E.; Oleynik, V.; Tereshchenko, V.; Epshtein, Y.; Chebotarev, V.

1996-01-01

The increase in the incidence of thyroid cancers in children and adolescents in Ukraine following the Chernobyl accident made it necessary to compile a clinical morphological register of respective cancers. In 1986-1994 there were 339 cases registered in children and adolescents, of them 211 children (who were operated at the age under 15 years) and 128 adolescents (who were operated at the age of 15-18 years). Before the Chernobyl accident (1981-1985) in Ukraine 59 cases of thyroid cancer in children and adolescents were reported: 25 cases in children and 34 cases in adolescents. This increase has been observed since 1990. In 1981-1985 the incidence rate (number of thyroid cancers per 100000 children population) ranged 0.04 - 0.06. In 1990 this estimate was 0.23 and in 1992-1994 0.36 - 0.43, thus a 7-10 fold increase exceeding the pre-Chernobyl level. In the 5 most contaminated northern regions of Ukraine (Kiev, Chernigov, Zhitomir, Cherkassy, Rovno regions) and the city of Kiev the incidence rate was much higher. For example, in 1984 it was 3.8 in Chernigov region, 1.6 in Zhitomir region. The total 'contribution' of the above-mentioned regions to the incidence of thyroid cancer in children after the Chernobyl accident makes more than 60%. It has been noted that in 1990-1994 there was an increase in the number of children operated at the age under 10, it means that these children were under 6 years at the time of the accident and were most sensitive to radioiodine exposure. As for the sex ratio, there has been a shift to males: in 1981-1985 F/M = 1.8/1, in 1990-1994 F/M = 1.4/1. Morphologically, 93.4% of 196 carcinomas resected from children and adolescents at the Institute of Endocrinology from 1986 to August 1st, 1995 were papillary carcinomas. They manifested high invasive and infiltrative growth, signs of intraglandular spread. Regional lymph node metastases were found in 59% of cases, distal lung metastases observed at various periods after surgery were noted

Optimizing the spatial pattern of networks for monitoring radioactive releases

NARCIS (Netherlands)

Melles, S.J.; Heuvelink, G.B.M.; Twenhofel, C.J.W.; Dijk, van A.; Hiemstra, P.H.; Baume, O.P.; Stohlker, U.

2011-01-01

This study presents a method to optimize the sampling design of environmental monitoring networks in a multi-objective setting. We optimize the permanent network of radiation monitoring stations in the Netherlands and parts of Germany as an example. The optimization method proposed combines

Environment, safety, and health at DOE facilities. Annual report, calendar year 1981

International Nuclear Information System (INIS)

1982-10-01

During 1981 the US Department of Energy's (DOE) safety and property protection performance remained excellent in all reported categories with loss rates generally less than one-third of comparable private-industry rates. The 1981 occupational-injury rates of 1.0 lost-workday cases and 13.5 lost workdays per 200,000 work hours were better than 1980 rates of 1.1 lost-workday cases and 17.5 lost workdays per 200,000 work hours. The recorded occupational illness rate, based on only 61 cases in 1981, was 0.04 cases per 200,000 work hours compared to 0.06 cases per 200,000 work hours for 1980. Property losses during 1981 totaled $4.7 million, with the largest loss of $1.25 million resulting from a fire at a Bonneville Power Administration lighting substation in Ellenberg, Washington. Fire losses during 1981 totaled $2.01 million, resulting in a fire loss rate of 0.38 cent per $100 property valuation - about one-eight the best class private-sector rate. Non-fire losses during 1981 totaled $2.65 million. The resulting non-fire loss rate of 0.48 cent per $100 property valuation was approx. one-third (36%) the 1980 loss rate of 1.34 cents per $100 property valuation. The 82,873 monitored Department of Energy federal and contractor employees received a total radiation dose of 6902 rem in 1981. The total amount of effluent radioactivity released from all DOE facilities in 1981 was 1.9 million curies, compared to 1.4 million curies in 1980. The largest probable whole-body radiation dose received by a maximally exposed public individual from any of these facilities was the same as in 1980: 15 millirem, or 3% of the DOE Radiation Protection Guide standard. A major accomplishemet during 1981 was the successful pilot testing of the Computerized Accident/Incident Reporting System (CAIRS), which will provide more-comprehensive safety information than the present data system

Enhanced Multi-Objective Optimization of Groundwater Monitoring Networks

DEFF Research Database (Denmark)

Bode, Felix; Binning, Philip John; Nowak, Wolfgang

Drinking-water well catchments include many sources for potential contaminations like gas stations or agriculture. Finding optimal positions of monitoring wells for such purposes is challenging because there are various parameters (and their uncertainties) that influence the reliability...... and optimality of any suggested monitoring location or monitoring network. The goal of this project is to develop and establish a concept to assess, design, and optimize early-warning systems within well catchments. Such optimal monitoring networks need to optimize three competing objectives: (1) a high...... be reduced to a minimum. The method is based on numerical simulation of flow and transport in heterogeneous porous media coupled with geostatistics and Monte-Carlo, wrapped up within the framework of formal multi-objective optimization. In order to gain insight into the flow and transport physics...

NUKEM annual report 1981

International Nuclear Information System (INIS)

The annual report of this important undertaking in the German nuclear industry informs about its structure, holdings and activities in 1981. The report of the management is followed by remarks on the annual statement of accounts (annual balance, profit-loss accounting) and the report of the Supervisory Board. In the annex the annual balance of NUKEM GmbH/HOBEG mbH as per December 31, 1981, and the profit-loss accounting of NUKEM GmbH/HOBEG mbH for the business year 1981 are presented. (UA) [de

Intercomparisons in the radiation monitoring network of the Czech Republic

Energy Technology Data Exchange (ETDEWEB)

Tuckova, S; Malatova, I [National Radiation Protection Inst., Prague (Czech Republic); Drabova, D [State Office for Nuclear Safety, Prague (Czech Republic)

1996-12-31

In Czech Republic, altogether 11 laboratories, equipped by semiconductor gamma spectrometry supply regularly to the Centre of Radiation Monitoring Network the measured data about the radionuclide activity concentration in different environmental samples, participating thus in monitoring of radiation situation in the country. The Center of Radiation Monitoring Network of Czech Republic periodically organizes through its reference laboratories interlaboratory comparison tests ensuring thus quality of the measurements within the radiation monitoring network. A ring intercomparison test was organized in 1994. The piece of steel rather highly contaminated by {sup 60}Co was used. In the intercomparison test 1994-1995 of pulverized concrete breeze-block containing fly ash with natural radionuclides were used. Results of this measurement is given as an example (authors).

Quality management status of national radiation environmental monitoring network and strategy for development

International Nuclear Information System (INIS)

Huang Renjie; Zhang Rongsuo; Ni Shiying; Shen Gang

2009-01-01

During the period of 10th five-year plan, MEP has constructed a national radiation environmental monitoring network. In the running of the network, quality management on monitoring data is of vital importance. So all the members of the radiation environmental monitoring network are required to ensure the quality of monitoring method, equipment, reagent,quality of personnel, data processing and information management and so on. Thus the monitoring result would be typical and accuracy in science. The article introduced in detail the quality management status of the National Radiation Environmental Monitoring Network and put forward the strategy for development from the institutionalized and large-scale point of view of radioactive environmental monitoring work. (authors)

Monitoring long-term ecological changes through the Ecological Monitoring and Assessment Network: science-based and policy relevant.

Science.gov (United States)

Vaughan, H; Brydges, T; Fenech, A; Lumb, A

2001-01-01

Ecological monitoring and its associated research programs have often provided answers to various environmental management issues. In the face of changing environmental conditions, ecological monitoring provides decision-makers with reliable information as they grapple with maintaining a sustainable economy and healthy environment. The Ecological Monitoring and Assessment Network (EMAN) is a national ecological monitoring network consisting of (1) about 100 case study sites across the country characterized by long-term multi-disciplinary environmental work conducted by a multitude of agencies (142 partners and counting); (2) a variety of less comprehensive yet more extensive monitoring sites; (3) a network where core monitoring variables of ecosystem change are measured; and (4) geo-referenced environmental observations. Environment Canada is the co-ordinating partner for the network through the EMAN Co-ordinating Office. EMAN's mission is to focus a scientifically-sound, policy-relevant ecosystem monitoring and research network based on (a) stabilizing a network of case-study sites operated by a variety of partners, and (b) developing a number of cooperative dispersed monitoring initiatives in order to deliver unique and needed goods and services. These goods and services include: (1) an efficient and cost-effective early warning system which detects, describes and reports on changes in Canadian ecosystems at a national or ecozone scale; and (2) cross-disciplinary and cross-jurisdictional assessments of ecosystem status, trends and processes. The early warning system and assessments of ecosystem status, trends and processes provide Environment Canada and partner organizations with timely information that facilitates increasingly adaptive policies and priority setting. Canadians are also informed of changes and trends occurring in Canadian ecosystems and, as a result, are better able to make decisions related to conservation and sustainability.

Modular Subsea Monitoring Network (MSM) - Realizing Integrated Environmental Monitoring Solutions

Science.gov (United States)

Mosch, Thomas; Fietzek, Peer

2016-04-01

In a variety of scientific and industrial application areas, ranging i.e. from the supervision of hydrate fields over the detection and localization of fugitive emissions from subsea oil and gas production to fish farming, fixed point observatories are useful and applied means. They monitor the water column and/or are placed at the sea floor over long periods of time. They are essential oceanographic platforms for providing valuable long-term time series data and multi-parameter measurements. Various mooring and observatory endeavors world-wide contribute valuable data needed for understanding our planet's ocean systems and biogeochemical processes. Continuously powered cabled observatories enable real-time data transmission from spots of interest close to the shore or to ocean infrastructures. Independent of the design of the observatories they all rely on sensors which demands for regular maintenance. This work is in most cases associated with cost-intensive maintenance on a regular time basis for the entire sensor carrying fixed platform. It is mandatory to encounter this asset for long-term monitoring by enhancing hardware efficiency. On the basis of two examples of use from the area of hydrate monitoring (off Norway and Japan) we will present the concept of the Modular Subsea Monitoring Network (MSM). The modular, scalable and networking capabilities of the MSM allow for an easy adaptation to different monitoring tasks. Providing intelligent power management, combining chemical and acoustical sensors, adaptation of the payload according to the monitoring tasks, autonomous powering, modular design for easy transportation, storage and mobilization, Vessel of Opportunity-borne launching and recovery capability with a video-guided launcher system and a rope recovery system are key facts addressed during the development of the MSM. Step by step the MSM concept applied to the observatory hardware will also be extended towards the gathered data to maximize the

Initial Results of a New Mobile Spectrum Occupancy Monitoring Network

NARCIS (Netherlands)

van Bloem, J.W.H.; Schiphorst, Roelof; Slump, Cornelis H.

2010-01-01

In this paper we present results of the new monitoring network for spectrum governance. The network is based on the RFeye system of CRFS where the data is collected employing mobile monitoring vehicles. The measurement data, obtained from a frequency sweep between 10 MHz and 6 GHz, is further

The central monitoring station of Indian Environmental Radiation Monitoring Network (IERMON): the architecture and functions

International Nuclear Information System (INIS)

Garg, Saurabh; Ratheesh, M.P.; Mukundan, T.; Patel, M.D.; Nair, C.K.G.; Puranik, V.D.

2010-01-01

The Indian Environmental Radiation Monitoring Network (IERMON) is being established across the country by the Bhabha Atomic Research Centre, Mumbai. The network consists of stations with automated systems for environmental radiation monitoring with online data communication facility. Currently about 100 stations are operational and additional 500 stations are expected to be installed by March, 2012. The network is established with different objectives, the main objective being the detection and reporting of any nuclear emergency anywhere in the country. The central monitoring station of the network is established in Mumbai. This paper describes the architecture and functions of IERMON Central Station. The Central Station consists of server room for online data collection from remote stations and maintenance of databases for various applications; central monitoring room for user interaction with database and IERMON website maintenance and development room for the development of new applications. The functions of IERMON Central Station include detection and reporting of nuclear emergency, maintenance of remote stations, enhancement of public awareness on environmental radiation through public display systems and website, etc. The details on system layout and data protocols can be found in the paper. (author)

Wireless sensor networks and ecological monitoring

CERN Document Server

Jiang, Joe-Air

2013-01-01

This book presents the state of the art technologies and solutions to tackle the critical challenges faced by the building and development of the WSN and ecological monitoring system but also potential impact on society at social, medical and technological level. This book is dedicated to Sensing systems for Sensors, Wireless Sensor Networks and Ecological Monitoring. The book aims at Master and PhD degree students, researchers, practitioners, especially WSN engineers involved with ecological monitoring. The book will provide an opportunity of a dedicated and a deep approach in order to improve their knowledge in this specific field.  

Static and mobile networks design for atmospheric accidental releases monitoring

International Nuclear Information System (INIS)

Abida, R.

2010-01-01

The global context of my PhD thesis work is the optimization of air pollution monitoring networks, but more specifically it concerns the monitoring of accidental releases of radionuclides in air. The optimization problem of air quality measuring networks has been addresses in the literature. However, it has not been addresses in the context of surveillance of accidental atmospheric releases. The first part of my thesis addresses the optimization of a permanent network of monitoring of radioactive aerosols in the air, covering France. The second part concerns the problem of targeting of observations in case of an accidental release of radionuclides from a nuclear plant. (author)

Environmental monitoring network for India

Science.gov (United States)

P.V. Sundareshwar; R. Murtugudde; G. Srinivasan; S. Singh; K.J. Ramesh; R. Ramesh; S.B. Verma; D. Agarwal; D. Baldocchi; C.K. Baru; K.K. Baruah; G.R. Chowdhury; V.K. Dadhwal; C.B.S. Dutt; J. Fuentes; Prabhat Gupta; W.W. Hardgrove; M. Howard; C.S. Jha; S. Lal; W.K. Michener; A.P. Mitra; J.T. Morris; R.R. Myneni; M. Naja; R. Nemani; R. Purvaja; S. Raha; S.K. Santhana Vanan; M. Sharma; A. Subramaniam; R. Sukumar; R.R. Twilley; P.R. Zimmerman

2007-01-01

Understanding the consequences of global environmental change and its mitigation will require an integrated global effort of comprehensive long-term data collection, synthesis, and action (1). The last decade has seen a dramatic global increase in the number of networked monitoring sites. For example, FLUXNET is a global collection of >300 micrometeorological...

Autonomous smart sensor network for full-scale structural health monitoring

Science.gov (United States)

Rice, Jennifer A.; Mechitov, Kirill A.; Spencer, B. F., Jr.; Agha, Gul A.

2010-04-01

The demands of aging infrastructure require effective methods for structural monitoring and maintenance. Wireless smart sensor networks offer the ability to enhance structural health monitoring (SHM) practices through the utilization of onboard computation to achieve distributed data management. Such an approach is scalable to the large number of sensor nodes required for high-fidelity modal analysis and damage detection. While smart sensor technology is not new, the number of full-scale SHM applications has been limited. This slow progress is due, in part, to the complex network management issues that arise when moving from a laboratory setting to a full-scale monitoring implementation. This paper presents flexible network management software that enables continuous and autonomous operation of wireless smart sensor networks for full-scale SHM applications. The software components combine sleep/wake cycling for enhanced power management with threshold detection for triggering network wide tasks, such as synchronized sensing or decentralized modal analysis, during periods of critical structural response.

Wireless Sensor Network Based Subsurface Contaminant Plume Monitoring

Science.gov (United States)

2012-04-16

Sensor Network (WSN) to monitor contaminant plume movement in naturally heterogeneous subsurface formations to advance the sensor networking based...time to assess the source and predict future plume behavior. This proof-of-concept research aimed at demonstrating the use of an intelligent Wireless

Radiation monitoring network in Poland

International Nuclear Information System (INIS)

Grabowski, D.; Kurowski, W.; Muszynski, W.; Rubel, B.; Smagala, G.; Swietochowska, J.

2001-01-01

In Poland the radioactive contamination of the environment and food has been controlled since the early sixties by the Service for Measurements of Radioactive Contamination (SPSP). The service comprises a network of measuring stations and the Centre of Radioactive Contamination Measurements (COPSP). Actually, there are 100 measurement stations. The main task of such station is systematic measurement of radioactivity level in samples of environment components and food. Nine stations of SPSP acting within meteorological stations, ten stations of low level air radioactivity measurements (Aerosols Sampling Stations-500) and eleven permanent monitoring stations (PMS) form the radiation monitoring warning system in Poland. (author)

NRC TLD Direct Radiation Monitoring Network

International Nuclear Information System (INIS)

Struckmeyer, R.; McNamara, N.

1991-12-01

This report provides the status and results of the NRC Thermoluminescent Dosimeter (TLD) Direct Radiation Monitoring Network. It presents the radiation levels measured in the vicinity of NRC licensed facilities throughout the country for the third quarter of 1991

Air Quality System (AQS) Monitoring Network, EPA OAR OAQPS

Data.gov (United States)

U.S. Environmental Protection Agency — This GIS dataset contains points which depict air quality monitors within EPA's Air Quality System (AQS) monitoring network. This dataset is updated weekly to...

Radiation monitoring network of the Czech Republic

International Nuclear Information System (INIS)

Drabova, D.; Prouza, Z.; Malatova, I.; Bucina, I.

1996-01-01

Radiation Monitoring Network of the Czech Republic (RMN) was established after the Chernobyl accident. It consists of technical centers, laboratories and monitoring groups of State Office for Nuclear Safety, National Radiation Protection Institute, nuclear power plants, hydrometeorological service, army and Civil Defense, research institutes and other institutions. The structure of RMN, its basic components and responsible institutions are described. (author)

Modification of GNPS environment radiation monitoring network system

International Nuclear Information System (INIS)

Jiang Lili; Cao Chunsheng

1999-01-01

GNPS Environment Radiation Continuous Monitoring System (KRS), the only real time on-line system of site radiation monitoring, was put into service in 1993 prior to the first loading the the plant. It is revealed through several years of operation that this system has some deficiencies such as inadequate real time monitoring means, no figure and diagram display function on the central computer, high failures, frequent failure warning signals, thus making the availability of the system at a low level. In recent years, with the rapid development of computer network technology and increasingly strict requirements on the NPP environment protection raised by the government and public, KRS modification had become necessary and urgent. In 1996, GNPS carried out modification work on the measuring geometry condition of γ radiation monitoring sub-station and lightening protection. To enhance the functions of real time monitoring and data auto-processing, further modification of the system was made in 1998, including the update of the software and hardware of KRS central processor, set-up of system computer local network and database. In this way, the system availability and monitoring quality are greatly improved and effective monitoring and analysis means are provided for gaseous release during normal operation and under accident condition

A New Mechanism for Network Monitoring and Shielding in Wireless LAN

Directory of Open Access Journals (Sweden)

Jiujun Cheng

2014-01-01

Full Text Available Wireless LAN (WLAN technology is developing rapidly with the help of wireless communication technology and social demand. During the development of WLAN, the security is more and more important, and wireless monitoring and shielding are of prime importance for network security. In this paper, we have explored various security issues of IEEE 802.11 based wireless network and analyzed numerous problems in implementing the wireless monitoring and shielding system. We identify the challenges which monitoring and shielding system needs to be aware of, and then provide a feasible mechanism to avoid those challenges. We implemented an actual wireless LAN monitoring and shielding system on Maemo operating system to monitor wireless network data stream efficiently and solve the security problems of mobile users. More importantly, the system analyzes wireless network protocols efficiently and flexibly, reveals rich information of the IEEE 802.11 protocol such as traffic distribution and different IP connections, and graphically displays later. Moreover, the system running results show that the system has the capability to work stably, and accurately and analyze the wireless protocols efficiently.

Environmental surveillance for the INEL Radioactive-Waste-Management complex. Annual report 1981

International Nuclear Information System (INIS)

Janke, D.H.; Zahn, T.P.

1982-09-01

The 1981 environmental surveillance report for the Radioactive Waste Management Complex of the Idaho National Engineering Laboratory contains data and discussions about routine radiological monitoring of the atmospheric, hydrologic, and geologic environments of the RWMC. Additional discussions include results of routine monitoring of two surplus facilities, the Stationary Low-Power Reactor No. 1 Surplus Area and the Organic Moderated Reactor Experiment. Each area has produced localized effects on the environment, but containment is well within the INEL site boundary

COMBINED AND STORM SEWER NETWORK MONITORING

OpenAIRE

Justyna Synowiecka; Ewa Burszta-Adamiak; Tomasz Konieczny; Paweł Malinowski

2014-01-01

Monitoring of the drainage networks is an extremely important tool used to understand the phenomena occurring in them. In an era of urbanization and increased run-off, at the expense of natural retention in the catchment, it helps to minimize the risk of local flooding and pollution. In its scope includes measurement of the amount of rainfall, with the use of rain gauges, and their measure in the sewer network, in matter of flows and channel filling, with the help of flow meters. An indispens...

Realization of Intelligent Household Appliance Wireless Monitoring Network Based on LEACH Protocol

Directory of Open Access Journals (Sweden)

Weilong ZHOU

2014-06-01

Full Text Available The intelligent household appliance wireless monitoring network can real-time monitor the apparent power and power factor of various household appliances in different indoor regions, and can realize the real-time monitoring on the household appliance working status and performance. The household appliance wireless monitoring network based on LEACH protocol is designed in the paper. Firstly, the basic idea of LEACH routing algorithm is proposed. Aiming at the node-distribution feature of intelligent home, the selection of cluster head in the routing algorithm and the data transmission method at the stable communication phase is modified. Moreover, the hardware circuit of power acquisition and power factor measurement is designed. The realization of wireless monitoring network based on CC2530 is described, each module and the whole system were conducted the on-line debugging. Finally, the system is proved to meet the practical requirement through the networking test.

Optimal Design of Multitype Groundwater Monitoring Networks Using Easily Accessible Tools.

Science.gov (United States)

Wöhling, Thomas; Geiges, Andreas; Nowak, Wolfgang

2016-11-01

Monitoring networks are expensive to establish and to maintain. In this paper, we extend an existing data-worth estimation method from the suite of PEST utilities with a global optimization method for optimal sensor placement (called optimal design) in groundwater monitoring networks. Design optimization can include multiple simultaneous sensor locations and multiple sensor types. Both location and sensor type are treated simultaneously as decision variables. Our method combines linear uncertainty quantification and a modified genetic algorithm for discrete multilocation, multitype search. The efficiency of the global optimization is enhanced by an archive of past samples and parallel computing. We demonstrate our methodology for a groundwater monitoring network at the Steinlach experimental site, south-western Germany, which has been established to monitor river-groundwater exchange processes. The target of optimization is the best possible exploration for minimum variance in predicting the mean travel time of the hyporheic exchange. Our results demonstrate that the information gain of monitoring network designs can be explored efficiently and with easily accessible tools prior to taking new field measurements or installing additional measurement points. The proposed methods proved to be efficient and can be applied for model-based optimal design of any type of monitoring network in approximately linear systems. Our key contributions are (1) the use of easy-to-implement tools for an otherwise complex task and (2) yet to consider data-worth interdependencies in simultaneous optimization of multiple sensor locations and sensor types. © 2016, National Ground Water Association.

Monthly results of measurements, October 1986

International Nuclear Information System (INIS)

1986-11-01

This October 1986 report of the SCPRI exposes an interpretation of the principal results concerning the routine monitoring of environmental radioactivity in France: atmospheric dusts, rainwater, surface water, underground water, sewage water, drinking water, food chain (milk, vegetables, fishes), sea water around nuclear plant sites and other sites. The activities of various radioisotopes are presented in tables. This report exposes also the results of special radiation measurements resulting from the Chernobyl accident, with an exceptional control of migratory birds [fr

Nuclear power plant monitoring using real-time learning neural network

International Nuclear Information System (INIS)

Nabeshima, Kunihiko; Tuerkcan, E.; Ciftcioglu, O.

1994-01-01

In the present research, artificial neural network (ANN) with real-time adaptive learning is developed for the plant wide monitoring of Borssele Nuclear Power Plant (NPP). Adaptive ANN learning capability is integrated to the monitoring system so that robust and sensitive on-line monitoring is achieved in real-time environment. The major advantages provided by ANN are that system modelling is formed by means of measurement information obtained from a multi-output process system, explicit modelling is not required and the modelling is not restricted to linear systems. Also ANN can respond very fast to anomalous operational conditions. The real-time ANN learning methodology with adaptive real-time monitoring capability is described below for the wide-range and plant-wide data from an operating nuclear power plant. The layered neural network with error backpropagation algorithm for learning has three layers. The network type is auto-associative, inputs and outputs are exactly the same, using 12 plant signals. (author)

An Efficient Wireless Sensor Network for Industrial Monitoring and Control.

Science.gov (United States)

Aponte-Luis, Juan; Gómez-Galán, Juan Antonio; Gómez-Bravo, Fernando; Sánchez-Raya, Manuel; Alcina-Espigado, Javier; Teixido-Rovira, Pedro Miguel

2018-01-10

This paper presents the design of a wireless sensor network particularly designed for remote monitoring and control of industrial parameters. The article describes the network components, protocol and sensor deployment, aimed to accomplish industrial constraint and to assure reliability and low power consumption. A particular case of study is presented. The system consists of a base station, gas sensing nodes, a tree-based routing scheme for the wireless sensor nodes and a real-time monitoring application that operates from a remote computer and a mobile phone. The system assures that the industrial safety quality and the measurement and monitoring system achieves an efficient industrial monitoring operations. The robustness of the developed system and the security in the communications have been guaranteed both in hardware and software level. The system is flexible and can be adapted to different environments. The testing of the system confirms the feasibility of the proposed implementation and validates the functional requirements of the developed devices, the networking solution and the power consumption management.

Neural network training by Kalman filtering in process system monitoring

International Nuclear Information System (INIS)

Ciftcioglu, Oe.

1996-03-01

Kalman filtering approach for neural network training is described. Its extended form is used as an adaptive filter in a nonlinear environment of the form a feedforward neural network. Kalman filtering approach generally provides fast training as well as avoiding excessive learning which results in enhanced generalization capability. The network is used in a process monitoring application where the inputs are measurement signals. Since the measurement errors are also modelled in Kalman filter the approach yields accurate training with the implication of accurate neural network model representing the input and output relationships in the application. As the process of concern is a dynamic system, the input source of information to neural network is time dependent so that the training algorithm presents an adaptive form for real-time operation for the monitoring task. (orig.)

Developing A National Groundwater-Monitoring Network In Korea

Science.gov (United States)

Kim, N. J.; Cho, M. J.; Woo, N. C.

1995-04-01

Since the 1960's, the groundwater resources of Korea have been developed without a proper regulatory system for monitoring and preservation, resulting in significant source depletion, land subsidence, water contamination, and sea-water intrusion. With the activation of the "Groundwater Law" in June 1994, the government initiated a project to develop a groundwater-monitoring network to describe general groundwater quality, to define its long-term changes, and to identify major factors affecting changes in groundwater quality and yield. In selecting monitoring locations nationwide, criteria considered are 1) spatial distribution, 2) aquifer characteristics of hydrogeologic units, 3) local groundwater flow regime, 4) linkage with surface hydrology observations, 5) site accessibility, and 6) financial situations. A total of 310 sites in 78 small hydrologic basins were selected to compose the monitoring network. Installation of monitoring wells is scheduled to start in 1995 for 15 sites; the remainder are scheduled to be completed by 2001. At each site, a nest of monitoring wells was designed; shallow and deep groundwater will be monitored for water temperature, pH, EC, DO and TDS every month. Water-level fluctuations will also be measured by automatic recorders equipped with pressure transducers. As a next step, the government plans to develop a groundwater-database management system, which could be linked with surface hydrologic data.

Monthly results of measurements, September 1986, with supplement related to the three months, July, August, September 1986

International Nuclear Information System (INIS)

1986-10-01

This report of the SCPRI exposes an interpretation of the principal results concerning the routine monitoring of environmental radioactivity in France: atmospheric dusts, rainwater, surface water, underground water, sewage water, drinking water, food chain (milk, vegetables, fishes) seawater around nuclear plant sites and other sites. The activities of various radioisotopes are presented in tables. This report exposes also the results of special radiation measurements resulting from the Chernobyl accident and complementary results related to the three months July, August, September 1986 [fr

Development of a reactor-coolant-pump monitoring and diagnostic system. Semi-annual progress report, December 1981-May 1982

International Nuclear Information System (INIS)

Morris, D.J.; Gabler, H.C.

1982-10-01

Reactor coolant (RC) pump seal failures have resulted in excessive leakage of primary coolant into reactor containment buildings. In some cases, high levels of airborne activity and surface contamination following these failures have necessitated extensive cleanup efforts and personnel radiation exposure. Unpredictable pump seal performance has also caused forced outages and frequent maintenance. The quality of operating data has been insufficient to allow proper evaluation of theoretical RC pump seal failure mechanisms. The RC pump monitoring and diagnostic system being developed and installed at Toledo Edison's Davis-Besse Nuclear Power Station will examine the relationship between seal failures and three other variables. This report describes system software and hardware development, testing, and installation work performed during the period of December 1981 through May 1982. Also described herein is a parallel effort being conducted by a B and W/Byron Jackson/Utility group to improve pump seal performance

Industrial Safety and Applied Health Physics Division annual report for 1981

International Nuclear Information System (INIS)

Auxier, J.A.; Oakes, T.W.

1982-08-01

Activities over the past year are summarized for the Health Physics Department, the Environmental Management Program, and the Safety Department. The Health Physics Department conducts radiation and safety surveys, provides personnel monitoring services for both external and internal radiation, and procures, services, and calibrates appropriate portable and stationary health physics instruments. It was determined that the maximum whole-body dose sustained by an employee was about 3.8 rems, which is 76% of the applicable standard of 5 rems. The greatest cumulative dose to the skin of the whole body received by an employee during 1981 was about 5.9 rems, or 39% of the applicable standard of 15 rems. Atmospheric iodine sampled by the Department of Environmental Management at the perimeter stations averged 0.13E to 14 μCi/cc during 1981. This average represents 131 I released to uncontrolled areas. All air samples taken had values below the allowable standards. The concentrations of 90 Sr in milk from both the immediate and remote environs of ORNL are also within FRC range I. The average value of 1.5 E to 9 μCi/mL represents 0.5% of the CG/sub w/ for drinking water applicable to individuals in the general population. The Safety Department reported that the continuing emphasis on safety during CY 1981 resulted in significant improvements in the ORNL safety program: safety performance was better than all CY 1981 on-the-job injury and illness goals. Through December 31, 1981, the Laboratory had worked 600 days and accumulated 14,015,826 exposure-hours since the last lost-work-day case

Environmental surveillance report for the Nevada Test Site (January 1981 through December 1981)

International Nuclear Information System (INIS)

Scoggins, W.A.

1982-05-01

This report documents the environmental surveillance program at the Nevada Test Site as conducted by the Department of Energy (DOE) onsite radiological safety contractor from January 1981 through December 1981. The results and evaluations of measurements of radioactivity in air and water, and of direct gamma radiation exposure rates are presented. Relevancy to DOE concentration guides (CG'S) is established

Optimisation of a bioindicator monitoring network using geostatic methods and a geographic information system; Optimierung eines Bioindikator-Messnetzes mit Hilfe geostatischer Methoden und eines Geographischen Informationssystems

Energy Technology Data Exchange (ETDEWEB)

Forster, E.M.

1994-04-01

Since 1981 the Bavarian State Authority for Environment Protection has used mosses (hypnum cupressiforme) as bioindicators for determining atmospheric background pollution. Covering all of Bavaria the monitoring network comprises more than 370 sampling sites spaced 8 km apart in urban regions and otherwise 16 km. The extremely labour-intensive and costly operation of the network led to the idea to thin it in such a way that the loss of information on regional background pollution would be kept as small as possible and remain within acceptable bounds. The geostatic methods used for this purpose permit an areal estimation of pollution load giving due consideration to local values as well as a calculation of the forecast error. The present report is divided into two sections: The first deals with the determination of spatial dependences, while the second concens the selection of sampling sites. (orig./KW) [Deutsch] Seit 1981 werden Moose (Hypnum cupressiforme) als Bioindikatoren zur Ermittlung der atmosphaerischen Hintergrundbelastung vom Bayerischen Landesamt fuer Umweltschutz eingesetzt. Das landesweite Messnetz umfasst mehr als 370 Probenahmestandorte, die 16 km bzw. in Verdichtungsregionen 8 km von einander entfernt liegen. Der erhebliche personelle und finanzielle Aufwand fuehrte zu der Ueberlegung das Messnetz mit moeglichst geringem, noch aktzeptablen Informationsverlust bezueglich der grossraeumigen Hintergrundbelastung zu reduzieren. Hierbei kamen geostatistische Methoden zum Einsatz, da sie eine flaechenhafte Schaetzung der Immissionsbelastung unter Beruecksichtigung der Umgebungswerte ermoeglichen. Zudem kann der Schaetzfehler berechnet werden. Die vorliegende Arbeit gliedert sich daher in zwei Bereiche: Einerseits das Feststellen raeumlicher Abhaengigkeiten und andererseits die Auswahl der Probenahmestandorte. (orig./KW)

Development and demonstration of indoor radon-reduction measures for 10 homes in Clinton, New Jersey. Final report, April 1986-January 1987

International Nuclear Information System (INIS)

Michaels, L.D.; Brennan, T.; Viner, A.S.; Mattes, A.; Turner, W.

1987-07-01

This report discusses the development and demonstration of indoor radon reduction methods for 10 houses in Clinton, New Jersey, where (in the spring of 1986) the New Jersey Department of Environmental Protection (DEP) located a cluster of houses with extremely high radon levels. The work was to be completed before the 1986-87 winter heating season began. The demonstration houses were selected from 56 in the Clinton Knolls subdivision. All of these houses had shown radon concentrations in excess of 64 pCi/1 when monitored in the spring of 1986. Each house was inspected, and 10 representative houses were selected for the radon-reduction demonstration project. Following intensive diagnostic work and monitoring in each house, house-specific radon-reduction plans were developed. With the agreement of the homeowners, radon-reduction systems were installed during the summer of 1986. All 10 of the houses had radon concentrations reduced significantly by the fall of 1986. The average cost of radon reduction was $3127

Wireless sensor network and monitoring for environment

OpenAIRE

Han, Liang

2011-01-01

In recent years, wireless sensor network technology is developing at a surprisingly high speed. More and more fields have started to use the wireless sensor network technology and find the advantages of WSN, such as military applications, environmental observing and forecasting system, medical care, smart home, structure monitoring. The world Environmental Summit in Copenhagen on 2010 has just concluded that environment has become the world’s main concern. But regrettably the summit did no...

AFR spent fuel storage program. Technical progress report, January 1981-March 1981

International Nuclear Information System (INIS)

1981-01-01

Work on this project is focused on developing design and licensing information for the model facility. Deliverables were submitted to DOE for facility modification, security design, and licensing documentation. Work is essentially complete on the high-density rack design with deliverable planned for April 30, 1981. A continuing program for completion of design and licensing information development was initiated by AGNS in February 1981. Progress to date is satisfactory

Continuous environmental radiation monitoring network at Kalpakkam

International Nuclear Information System (INIS)

Somayaji, K.M.; Mathiyarasu, R.; Prakash, G.S.; Meenakshisundaram, V.; Rajagopal, V.

1997-01-01

The report highlights our experience in the design and installation of monitoring stations as part of continuous environmental radiation monitoring network around the periphery of the nuclear complex at Kalpakkam. Five monitoring stations, one each in south-west sector (Main Gate I) and south-south west (Main Gate II) and the others in North sector (HASL and ESG) and in north-west section (WIP) have been set up. Two independent detector systems, based on high pressure ionisation chamber (HPIC) and energy compensated GM have been installed at each of these locations and the data has been logged continuously using a data logger. The data so gathered at each monitoring station is retrieved every week by means of a hand held terminal (HHT) with a built-in non-volatile memory and transferred to an IBM PC-AT for data analysis and archival. The report discusses in depth the design and developmental efforts undertaken to set up the network, starting from the basic detectors. The work involved the design of suitable electrometer circuits for measuring the low levels of current from HPICs, and the subsequent study of the performance of the highly sensitive preamplifier under diurnal variations of ambient conditions. The report includes, in detail the design aspects and fabrication details of low current measuring electrometer circuits

Helicopter Rotor Blade Monitoring using Autonomous Wireless Sensor Network

NARCIS (Netherlands)

Sanchez Ramirez, Andrea; Loendersloot, Richard; Tinga, Tiedo; Basu, B.

2013-01-01

The advancement on Wireless Sensor Networks for vibration monitoring presents important possibilities for helicopter rotor health and usage monitoring. While main rotor blades account for the main source of lift for helicopters, rotor induced vibration establishes an important source for

Application for vibration monitoring of aspheric surface machining based on wireless sensor networks

Science.gov (United States)

Han, Chun Guang; Guo, Yin Biao; Jiang, Chen

2010-05-01

Any kinds of tiny vibration of machine tool parts will have a great influence on surface quality of the workpiece at ultra-precise machining process of aspheric surface. At present the major way for decreasing influence of vibration is machining compensation technology. Therefore it is important for machining compensation control to acquire and transmit these vibration signals effectively. This paper presents a vibration monitoring system of aspheric surface machining machine tool based on wireless sensor networks (WSN). Some key issues of wireless sensor networks for vibration monitoring system of aspheric surface machining are discussed. The reliability of data transmission, network communication protocol and synchronization mechanism of wireless sensor networks are studied for the vibration monitoring system. The proposed system achieves multi-sensors vibration monitoring involving the grinding wheel, the workpiece and the workbench spindle. The wireless transmission of vibration signals is achieved by the combination with vibration sensor nodes and wireless network. In this paper, these vibration sensor nodes are developed. An experimental platform is structured which employs wireless sensor networks to the vibration monitoring system in order to test acquisition and wireless transmission of vibration signal. The test results show that the proposed system can achieve vibration data transmission effectively and reliability and meet the monitoring requirements of aspheric surface machining machine tool.

Licensee contractor and vendor inspection status report: Quarterly report, July 1986-September 1986

International Nuclear Information System (INIS)

1986-11-01

This periodical covers the results of inspections performed by the NRC's Vendor Program Branch that have been distributed to the inspected organizations during the period from July 1986 thru September 1986. Also, included in this issue are the results of certain inspections performed prior to July 1986 that were not previously reported

Optimal river monitoring network using optimal partition analysis: a case study of Hun River, Northeast China.

Science.gov (United States)

Wang, Hui; Liu, Chunyue; Rong, Luge; Wang, Xiaoxu; Sun, Lina; Luo, Qing; Wu, Hao

2018-01-09

River monitoring networks play an important role in water environmental management and assessment, and it is critical to develop an appropriate method to optimize the monitoring network. In this study, an effective method was proposed based on the attainment rate of National Grade III water quality, optimal partition analysis and Euclidean distance, and Hun River was taken as a method validation case. There were 7 sampling sites in the monitoring network of the Hun River, and 17 monitoring items were analyzed once a month during January 2009 to December 2010. The results showed that the main monitoring items in the surface water of Hun River were ammonia nitrogen (NH 4 + -N), chemical oxygen demand, and biochemical oxygen demand. After optimization, the required number of monitoring sites was reduced from seven to three, and 57% of the cost was saved. In addition, there were no significant differences between non-optimized and optimized monitoring networks, and the optimized monitoring networks could correctly represent the original monitoring network. The duplicate setting degree of monitoring sites decreased after optimization, and the rationality of the monitoring network was improved. Therefore, the optimal method was identified as feasible, efficient, and economic.

Water quality monitoring for high-priority water bodies in the Sonoran Desert network

Science.gov (United States)

Terry W. Sprouse; Robert M. Emanuel; Sara A. Strorrer

2005-01-01

This paper describes a network monitoring program for “high priority” water bodies in the Sonoran Desert Network of the National Park Service. Protocols were developed for monitoring selected waters for ten of the eleven parks in the Network. Park and network staff assisted in identifying potential locations of testing sites, local priorities, and how water quality...

BABY MONITORING SYSTEM USING WIRELESS SENSOR NETWORKS

Directory of Open Access Journals (Sweden)

G. Rajesh

2014-09-01

Full Text Available Sudden Infant Death Syndrome (SIDS is marked by the sudden death of an infant during sleep that is not predicted by the medical history and remains unexplained even after thorough forensic autopsy and detailed death investigation. In this we developed a system that provides solutions for the above problems by making the crib smart using the wireless sensor networks (WSN and smart phones. The system provides visual monitoring service through live video, alert services by crib fencing and awakens alert, monitoring services by temperature reading and light intensity reading, vaccine reminder and weight monitoring.

Patient Health Monitoring Using Wireless Body Area Network

Directory of Open Access Journals (Sweden)

Hsu Myat Thwe

2015-06-01

Full Text Available Abstract Nowadays remote patient health monitoring using wireless technology plays very vigorous role in a society. Wireless technology helps monitoring of physiological parameters like body temperature heart rate respiration blood pressure and ECG. The main aim of this paper is to propose a wireless sensor network system in which both heart rate and body temperature ofmultiplepatients can monitor on PC at the same time via RF network. The proposed prototype system includes two sensor nodes and receiver node base station. The sensor nodes are able to transmit data to receiver using wireless nRF transceiver module.The nRF transceiver module is used to transfer the data from microcontroller to PC and a graphical user interface GUI is developed to display the measured data and save to database. This system can provide very cheaper easier and quick respondent history of patient.

Applications of Wireless Sensor Networks in Marine Environment Monitoring: A Survey

Science.gov (United States)

Xu, Guobao; Shen, Weiming; Wang, Xianbin

2014-01-01

With the rapid development of society and the economy, an increasing number of human activities have gradually destroyed the marine environment. Marine environment monitoring is a vital problem and has increasingly attracted a great deal of research and development attention. During the past decade, various marine environment monitoring systems have been developed. The traditional marine environment monitoring system using an oceanographic research vessel is expensive and time-consuming and has a low resolution both in time and space. Wireless Sensor Networks (WSNs) have recently been considered as potentially promising alternatives for monitoring marine environments since they have a number of advantages such as unmanned operation, easy deployment, real-time monitoring, and relatively low cost. This paper provides a comprehensive review of the state-of-the-art technologies in the field of marine environment monitoring using wireless sensor networks. It first describes application areas, a common architecture of WSN-based oceanographic monitoring systems, a general architecture of an oceanographic sensor node, sensing parameters and sensors, and wireless communication technologies. Then, it presents a detailed review of some related projects, systems, techniques, approaches and algorithms. It also discusses challenges and opportunities in the research, development, and deployment of wireless sensor networks for marine environment monitoring. PMID:25215942

Nuclear medicine and imaging research. Progress report, January 1, 1981-December 31, 1981

International Nuclear Information System (INIS)

Beck, R.N.; Cooper, M.C.

1981-09-01

The Progress Report for the period January 1, 1981-December 31, 1981 of the Franklin Memorial Research Institute discusses instrumentation and quantitative methods of evaluation in nuclear medicine and imaging research. Imaging systems and image evaluation are discussed in four projects: Radiation Detector Studies, Dual Purpose Scanner for Thyroid Imaging, Instrumentation for Image Processing and Enhancement, and Energy-Coded Processing in Nuclear Medicine

Neural networks for sensor validation and plant monitoring

International Nuclear Information System (INIS)

Upadhyaya, B.R.; Eryurek, E.; Mathai, G.

1990-01-01

Sensor and process monitoring in power plants require the estimation of one or more process variables. Neural network paradigms are suitable for establishing general nonlinear relationships among a set of plant variables. Multiple-input multiple-output autoassociative networks can follow changes in plant-wide behavior. The backpropagation algorithm has been applied for training feedforward networks. A new and enhanced algorithm for training neural networks (BPN) has been developed and implemented in a VAX workstation. Operational data from the Experimental Breeder Reactor-II (EBR-II) have been used to study the performance of BPN. Several results of application to the EBR-II are presented

Monitoring network for doserate-measurements with wireless datatransmitting in Baden-Wuerttemberg

International Nuclear Information System (INIS)

Aures, R.; Wenzel, H.

2003-01-01

In the environment of the nuclear power plants Philippsburg, Obrigheim and Neckarwestheim in Baden-Wuerttemberg there is a monitoring network with 90 stations. They are measuring the gamma-dose rate. In the meantime these monitoring stations are nearly 20 years old and now it is time to substitute old technology by a new one. The aim is a mix of monitoring stations with phone wire- and wireless data transmission (Skylink). Thinkable is a part of 50 % of Skylink-tubes in the monitoring network and some for mobile performance. The main aspect of the planned substitution is a second independent way of data transmission. Normally there are no problems for data transmission. But in case of emergency the data transmissions which depends from phone wires could be delayed if there are too much dates. So the second way, the way of wireless data transmissions becomes important. The Landesanstalt fuer Umweltschutz in Karlsruhe has bought a complete system from the company Genitron in Frankfurt/Main. The system (Skylink) consists of the receiver and the does rate-monitoring stations. Such a system was tested successfully in a region with many mountains and deep valleys. Since July 2000 the Skylink-system is performed in the ''Nuclear power monitoring system'' (KFUe) in Baden-Wuerttemberg. The receiver is on the Koenigstuhl (630 m) near Heidelberg. This is a very good position to receive the wireless transmitted dates from every monitoring station (Skylink Gammatracer) of the monitoring network. Now there are 27 Skylink Gammatracer spread in the monitoring network. At time they are placed near the dose rate tubes of the old monitoring stations for comparing the dose rates and they are working with best results. (orig.)

Licensee contractor and vendor inspection status report: Quarterly report, October 1986-December 1986

International Nuclear Information System (INIS)

1987-02-01

This periodical covers the results of inspections performed by the NRC's Vendor Program Branch that have been distributed to the inspected organizations during the period from October 1986 through December 1986. Also, included in this issue are the results of certain inspections performed prior to October 1986 that were not included in previous issues of NUREG-0040

Design and Evaluation of a Proxy-Based Monitoring System for OpenFlow Networks.

Science.gov (United States)

Taniguchi, Yoshiaki; Tsutsumi, Hiroaki; Iguchi, Nobukazu; Watanabe, Kenzi

2016-01-01

Software-Defined Networking (SDN) has attracted attention along with the popularization of cloud environment and server virtualization. In SDN, the control plane and the data plane are decoupled so that the logical topology and routing control can be configured dynamically depending on network conditions. To obtain network conditions precisely, a network monitoring mechanism is necessary. In this paper, we focus on OpenFlow which is a core technology to realize SDN. We propose, design, implement, and evaluate a network monitoring system for OpenFlow networks. Our proposed system acts as a proxy between an OpenFlow controller and OpenFlow switches. Through experimental evaluations, we confirm that our proposed system can capture packets and monitor traffic information depending on administrator's configuration. In addition, we show that our proposed system does not influence significant performance degradation to overall network performance.

Design and Evaluation of a Proxy-Based Monitoring System for OpenFlow Networks

Directory of Open Access Journals (Sweden)

Yoshiaki Taniguchi

2016-01-01

Full Text Available Software-Defined Networking (SDN has attracted attention along with the popularization of cloud environment and server virtualization. In SDN, the control plane and the data plane are decoupled so that the logical topology and routing control can be configured dynamically depending on network conditions. To obtain network conditions precisely, a network monitoring mechanism is necessary. In this paper, we focus on OpenFlow which is a core technology to realize SDN. We propose, design, implement, and evaluate a network monitoring system for OpenFlow networks. Our proposed system acts as a proxy between an OpenFlow controller and OpenFlow switches. Through experimental evaluations, we confirm that our proposed system can capture packets and monitor traffic information depending on administrator’s configuration. In addition, we show that our proposed system does not influence significant performance degradation to overall network performance.

An Efficient Wireless Sensor Network for Industrial Monitoring and Control

Science.gov (United States)

Aponte-Luis, Juan; Gómez-Bravo, Fernando; Sánchez-Raya, Manuel; Alcina-Espigado, Javier; Teixido-Rovira, Pedro Miguel

2018-01-01

This paper presents the design of a wireless sensor network particularly designed for remote monitoring and control of industrial parameters. The article describes the network components, protocol and sensor deployment, aimed to accomplish industrial constraint and to assure reliability and low power consumption. A particular case of study is presented. The system consists of a base station, gas sensing nodes, a tree-based routing scheme for the wireless sensor nodes and a real-time monitoring application that operates from a remote computer and a mobile phone. The system assures that the industrial safety quality and the measurement and monitoring system achieves an efficient industrial monitoring operations. The robustness of the developed system and the security in the communications have been guaranteed both in hardware and software level. The system is flexible and can be adapted to different environments. The testing of the system confirms the feasibility of the proposed implementation and validates the functional requirements of the developed devices, the networking solution and the power consumption management. PMID:29320466

An Efficient Wireless Sensor Network for Industrial Monitoring and Control

Directory of Open Access Journals (Sweden)

Juan Aponte-Luis

2018-01-01

Full Text Available This paper presents the design of a wireless sensor network particularly designed for remote monitoring and control of industrial parameters. The article describes the network components, protocol and sensor deployment, aimed to accomplish industrial constraint and to assure reliability and low power consumption. A particular case of study is presented. The system consists of a base station, gas sensing nodes, a tree-based routing scheme for the wireless sensor nodes and a real-time monitoring application that operates from a remote computer and a mobile phone. The system assures that the industrial safety quality and the measurement and monitoring system achieves an efficient industrial monitoring operations. The robustness of the developed system and the security in the communications have been guaranteed both in hardware and software level. The system is flexible and can be adapted to different environments. The testing of the system confirms the feasibility of the proposed implementation and validates the functional requirements of the developed devices, the networking solution and the power consumption management.

Quality assurance and quality control for Hydro-Quebec's ambient air monitoring networks

International Nuclear Information System (INIS)

Lambert, M.; Varfalvy, L.

1993-01-01

Hydro Quebec has three ambient air monitoring networks to determine the contribution of some of its thermal plants to ambient air quality. They are located in Becancour (gas turbines), Iles-de-la-Madeleine (diesel), and Tracy (conventional oil-fired). To ensure good quality results and consistency between networks, a quality assurance/quality control program was set up. A description is presented of the ambient air quality monitoring network and the quality assurance/quality control program. A guide has been created for use by the network operators, discussing objectives of the individual network, a complete description of each network, field operation for each model of instrument in use, treatment of data for each data logger in use, global considerations regarding quality assurance and control, and reports. A brief overview is presented of the guide's purpose and contents, focusing on the field operation section and the sulfur dioxide and nitrogen oxide monitors. 6 figs., 1 tab

A SMART MONITORING SYSTEM FOR CAMPUS USING ZIGBEE WIRELESS SENSOR NETWORKS

Directory of Open Access Journals (Sweden)

Alaa Azmi Allahham

2018-02-01

Full Text Available The wireless sensor networks are autonomous sensors that are distributed to monitor environmental and physical conditions and pass them across the network to other areas, which is considered one of the key elements that are used in the applications of smart cities. Therefore, this paper aims to provide a design to add more smart applications to the sanctuary and other compounds based on wireless sensor networks using ZigBee technology. The transition from reliance on the style of surveillance and controlled manually by staff to apply the principles of smart applications through wireless sensor network which provides the ability to getting all the necessary information and capabilities of controlling and monitoring are required to automatically and thus saving the time, effort, and money. The system proposed in this paper to design a smart monitoring system at the campus to control the opening and closing of the doors of many halls and the possibility of including lighting systems and appliances. The results obtained from OPNET program show that the network topology, which used within a ZigBee network vary in terms of performance, thus giving options for designers to build their network and choose technologies that suit their project.

Construct mine environment monitoring system based on wireless mesh network

Science.gov (United States)

Chen, Xin; Ge, Gengyu; Liu, Yinmei; Cheng, Aimin; Wu, Jun; Fu, Jun

2018-04-01

The system uses wireless Mesh network as a network transmission medium, and strive to establish an effective and reliable underground environment monitoring system. The system combines wireless network technology and embedded technology to monitor the internal data collected in the mine and send it to the processing center for analysis and environmental assessment. The system can be divided into two parts: the main control network module and the data acquisition terminal, and the SPI bus technology is used for mutual communication between them. Multi-channel acquisition and control interface design Data acquisition and control terminal in the analog signal acquisition module, digital signal acquisition module, and digital signal output module. The main control network module running Linux operating system, in which the transplant SPI driver, USB card driver and AODV routing protocol. As a result, the internal data collection and reporting of the mine are realized.

Performance of monitoring networks estimated from a Gaussian plume model

International Nuclear Information System (INIS)

Seebregts, A.J.; Hienen, J.F.A.

1990-10-01

In support of the ECN study on monitoring strategies after nuclear accidents, the present report describes the analysis of the performance of a monitoring network in a square grid. This network is used to estimate the distribution of the deposition pattern after a release of radioactivity into the atmosphere. The analysis is based upon a single release, a constant wind direction and an atmospheric dispersion according to a simplified Gaussian plume model. A technique is introduced to estimate the parameters in this Gaussian model based upon measurements at specific monitoring locations and linear regression, although this model is intrinsically non-linear. With these estimated parameters and the Gaussian model the distribution of the contamination due to deposition can be estimated. To investigate the relation between the network and the accuracy of the estimates for the deposition, deposition data have been generated by the Gaussian model, including a measurement error by a Monte Carlo simulation and this procedure has been repeated for several grid sizes, dispersion conditions, number of measurements per location, and errors per single measurement. The present technique has also been applied for the mesh sizes of two networks in the Netherlands, viz. the Landelijk Meetnet Radioaciviteit (National Measurement Network on Radioactivity, mesh size approx. 35 km) and the proposed Landelijk Meetnet Nucleaire Incidenten (National Measurement Network on Nuclear Incidents, mesh size approx. 15 km). The results show accuracies of 11 and 7 percent, respectively, if monitoring locations are used more than 10 km away from the postulated accident site. These figures are based upon 3 measurements per location and a dispersion during neutral weather with a wind velocity of 4 m/s. For stable weather conditions and low wind velocities, i.e. a small plume, the calculated accuracies are at least a factor 1.5 worse.The present type of analysis makes a cost-benefit approach to the

Value of monitoring in road network management

NARCIS (Netherlands)

Zouch, M.; Courage, W.; Napoles-Morales, O.

2014-01-01

We present a framework for road network management to assist road authorities in maintenance budget estimations and long-term maintenance strategies definition. Information about road conditions is obtained from monitoring. Available data are used to estimate and update prediction of degradation

Assessing and optimizing infra-sound networks to monitor volcanic eruptions

International Nuclear Information System (INIS)

Tailpied, Dorianne

2016-01-01

Understanding infra-sound signals is essential to monitor compliance with the Comprehensive Nuclear-Test ban Treaty, and also to demonstrate the potential of the global monitoring infra-sound network for civil and scientific applications. The main objective of this thesis is to develop a robust tool to estimate and optimize the performance of any infra-sound network to monitor explosive sources such as volcanic eruptions. Unlike previous studies, the developed method has the advantage to consider realistic atmospheric specifications along the propagation path, source frequency and noise levels at the stations. It allows to predict the attenuation and the minimum detectable source amplitude. By simulating the performances of any infra-sound networks, it is then possible to define the optimal configuration of the network to monitor a specific region, during a given period. When carefully adding a station to the existing network, performance can be improved by a factor of 2. However, it is not always possible to complete the network. A good knowledge of detection capabilities at large distances is thus essential. To provide a more realistic picture of the performance, we integrate the atmospheric longitudinal variability along the infra-sound propagation path in our simulations. This thesis also contributes in providing a confidence index taking into account the uncertainties related to propagation and atmospheric models. At high frequencies, the error can reach 40 dB. Volcanic eruptions are natural, powerful and valuable calibrating sources of infra-sound, worldwide detected. In this study, the well instrumented volcanoes Yasur, in Vanuatu, and Etna, in Italy, offer a unique opportunity to validate our attenuation model. In particular, accurate comparisons between near-field recordings and far-field detections of these volcanoes have helped to highlight the potential of our simulation tool to remotely monitor volcanoes. Such work could significantly help to prevent

Industrial Safety and Applied Health Physics Division annual report for 1981

Energy Technology Data Exchange (ETDEWEB)

Auxier, J.A.; Oakes, T.W.

1982-08-01

Activities over the past year are summarized for the Health Physics Department, the Environmental Management Program, and the Safety Department. The Health Physics Department conducts radiation and safety surveys, provides personnel monitoring services for both external and internal radiation, and procures, services, and calibrates appropriate portable and stationary health physics instruments. It was determined that the maximum whole-body dose sustained by an employee was about 3.8 rems, which is 76% of the applicable standard of 5 rems. The greatest cumulative dose to the skin of the whole body received by an employee during 1981 was about 5.9 rems, or 39% of the applicable standard of 15 rems. Atmospheric iodine sampled by the Department of Environmental Management at the perimeter stations averged 0.13E to 14 ..mu..Ci/cc during 1981. This average represents < 0.005% of the concentration guide of 1E to 10 ..mu..Ci/cc applicable to inhalation of /sup 131/I released to uncontrolled areas. All air samples taken had values below the allowable standards. The concentrations of /sup 90/Sr in milk from both the immediate and remote environs of ORNL are also within FRC range I. The average value of 1.5 E to 9 ..mu..Ci/mL represents 0.5% of the CG/sub w/ for drinking water applicable to individuals in the general population. The Safety Department reported that the continuing emphasis on safety during CY 1981 resulted in significant improvements in the ORNL safety program: safety performance was better than all CY 1981 on-the-job injury and illness goals. Through December 31, 1981, the Laboratory had worked 600 days and accumulated 14,015,826 exposure-hours since the last lost-work-day case.

Correlation of PCDD/F and PCB concentrations in soil samples from the Swiss Soil Monitoring Network (NABO) to specific parameters of the observation sites

Energy Technology Data Exchange (ETDEWEB)

Schmid, P.; Gujer, E.; Zennegg, M. [Swiss Federal Laboratories for Materials Testing and Research (EMPA), Duebendorf (Switzerland); Bucheli, T. [Agroscope FAL Reckenholz, Zuerich (Switzerland)

2004-09-15

Soils are natural sinks for persistent organic pollutants (POPs) such as polychlorinated dibenzo-pdioxins (PCDD/F) and polychlorinated biphenyls (PCB). Being lipophilic compounds, these contaminants adsorb to the organic carbon of the soil, and due to the low mobility and high persistence, they accumulate in the soil. Soil therefore represents rather a long-term archive for the atmospheric deposition than an indicator for the actual input of these compounds. In 1986, on demand of the Swiss ordinance of 9 June 1986 relating to hazardous substances in the soil, a national soil monitoring network (NABO) was set up in Switzerland aiming at monitoring the soil pollution. Sites were selected to reflect typical land use, vegetation, land management, air quality, and soil conditions in Switzerland. 50% of the sites are located on agricultural land, 30% in forests, and 20% on open land with extensive farming (alpine pastures, etc.); two sites are situated in urban parks. The sites are distributed throughout Switzerland including rural/remote areas as well as urban, urban fringe and industrial regions. Soil samples are taken every 5 years and are analysed for eight heavy metals (lead, copper, cadmium, zinc, nickel, chromium, cobalt, and mercury) as well as fluorine. So far, organic pollutants (PAH and PCB) have been determined in isolated samples only, and there is no data on PCDD/F concentrations so far. The present program was set up to fill this knowledge gap. A subset of 23 sites representing locations where contaminant immissions above average were expected was selected for PCDD/F and PCB analysis.

Performance Monitoring Techniques Supporting Cognitive Optical Networking

DEFF Research Database (Denmark)

Caballero Jambrina, Antonio; Borkowski, Robert; Zibar, Darko

2013-01-01

High degree of heterogeneity of future optical networks, such as services with different quality-of-transmission requirements, modulation formats and switching techniques, will pose a challenge for the control and optimization of different parameters. Incorporation of cognitive techniques can help...... to solve this issue by realizing a network that can observe, act, learn and optimize its performance, taking into account end-to-end goals. In this letter we present the approach of cognition applied to heterogeneous optical networks developed in the framework of the EU project CHRON: Cognitive...... Heterogeneous Reconfigurable Optical Network. We focus on the approaches developed in the project for optical performance monitoring, which enable the feedback from the physical layer to the cognitive decision system by providing accurate description of the performance of the established lightpaths....

Using modular neural networks to monitor accident conditions in nuclear power plants

International Nuclear Information System (INIS)

Guo, Z.

1992-01-01

Nuclear power plants are very complex systems. The diagnoses of transients or accident conditions is very difficult because a large amount of information, which is often noisy, or intermittent, or even incomplete, need to be processed in real time. To demonstrate their potential application to nuclear power plants, neural networks axe used to monitor the accident scenarios simulated by the training simulator of TVA's Watts Bar Nuclear Power Plant. A self-organization network is used to compress original data to reduce the total number of training patterns. Different accident scenarios are closely related to different key parameters which distinguish one accident scenario from another. Therefore, the accident scenarios can be monitored by a set of small size neural networks, called modular networks, each one of which monitors only one assigned accident scenario, to obtain fast training and recall. Sensitivity analysis is applied to select proper input variables for modular networks

Network Monitoring as a Streaming Analytics Problem

KAUST Repository

Gupta, Arpit; Birkner, Rü diger; Canini, Marco; Feamster, Nick; Mac-Stoker, Chris; Willinger, Walter

2016-01-01

, processing such network monitoring queries at high traffic rates requires both the switches and the stream processors to filter the traffic iteratively and adaptively so as to extract only that traffic that is of interest to the query at hand. Others have

Application of wireless sensor networks in personnel dosage monitoring system of nuclear power plant

International Nuclear Information System (INIS)

Chen Yonghong; Zhang Dafa; Jiang Wei; Chen Dengke

2007-01-01

Aim to meet the need of personnel dosage monitoring of nuclear power plant, a monitoring system was designed which based on wireless sensor network. First, the basic concept was described; the characteristics of the wireless sensor network applied in the monitoring system of nuclear power plant were also been analyzed; the structure of the system was built too. Finally, the special technologies like the choice of communication mode, the security of communication network and orientation that used in the monitoring system were discussed. (authors)

Development of a Compact Gamma-ray Detector for a Neural-Network Radiation Monitoring

Energy Technology Data Exchange (ETDEWEB)

Kim, H. S.; Ha, J. H.; Lee, K. H. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, C. H. [Hanyang Univ., Seoul (Korea, Republic of)

2012-03-15

Radiation monitoring is very important to secure safety in nuclear-related facilities and against nuclear terrorism. For wide range of radiation monitoring, neutral network system of radiation detection is most efficient way. Thus, a compact radiation detector is useful to install in wide range to be concerned. A compact gamma-ray detector was fabricated by using a CsI(Tl) scintillator, which was matched with the formerly developed PIN photodiode, for a neural network radiation monitoring. At room temperature, the fabricated compact gamma-ray detector demonstrates an energy resolution of 13.3 % for 662 keV 6.9% for 1330 keV. The compactness, the low-voltage power consumption and the physical hardness are very useful features for a neural network radiation monitoring. In this study, characteristics of a fabricated compact gamma-ray detector were presented. An important aspect to consider in a neural-network radiation monitoring such as reaction probability of the fabricated compact detector for angle of incident gamma-ray was also addressed.

Event localization in underwater wireless sensor networks using Monitoring Courses

KAUST Repository

Debont, Matthew John Robert; Jamshaid, Kamran; Shihada, Basem; Ho, Pin-Han

2012-01-01

We propose m-courses (Monitoring Courses), a novel solution to localize events in an underwater wireless sensor network. These networks consists of surface gateways and relay nodes. GPS can localize the position of surface gateways which can

National forest change monitoring system in South Korea: an analysis of forest tree species distribution shifts

Science.gov (United States)

Eun-Sook Kim; Cheol-Min Kim; Jisun Lee; Jong-Su. Yim

2015-01-01

Since 1971, South Korea has implemented national forest inventory (NFI) in pursuance of understanding current state and change trend of national forest resources. NFI1 (1971~1975), NFI2 (1978~1981), NFI3 (1986~1992) and NFI4 (1996~2005) were implemented in order to produce national forest resources statistics. However, since the early 1990s, international conventions...

Unobstructive Body Area Networks (BAN) for efficient movement monitoring.

Science.gov (United States)

Felisberto, Filipe; Costa, Nuno; Fdez-Riverola, Florentino; Pereira, António

2012-01-01

The technological advances in medical sensors, low-power microelectronics and miniaturization, wireless communications and networks have enabled the appearance of a new generation of wireless sensor networks: the so-called wireless body area networks (WBAN). These networks can be used for continuous monitoring of vital parameters, movement, and the surrounding environment. The data gathered by these networks contributes to improve users' quality of life and allows the creation of a knowledge database by using learning techniques, useful to infer abnormal behaviour. In this paper we present a wireless body area network architecture to recognize human movement, identify human postures and detect harmful activities in order to prevent risk situations. The WBAN was created using tiny, cheap and low-power nodes with inertial and physiological sensors, strategically placed on the human body. Doing so, in an as ubiquitous as possible way, ensures that its impact on the users' daily actions is minimum. The information collected by these sensors is transmitted to a central server capable of analysing and processing their data. The proposed system creates movement profiles based on the data sent by the WBAN's nodes, and is able to detect in real time any abnormal movement and allows for a monitored rehabilitation of the user.

The Security Plan for the Joint Euratom/IAEA Remote Monitoring Network

International Nuclear Information System (INIS)

Stronkhorst, J.; Schoop, K.; Ruuska, K.; Kurek, S.; Levert, J.F.

2015-01-01

The European Commission and the IAEA have installed surveillance systems in all larger civil European nuclear facilities. The monitoring data is gathered by optical surveillance systems, electronic sealing systems and numerous measuring devices. The on-site joint Euratom/IAEA monitoring networks operate in general completely isolated from the operator's IT systems. To largely improve data security and reliability, remote data transmission (RDT) is installed on a growing number of sites, and the inspection data is daily transferred to the Data Collect Servers in Luxembourg and Vienna. A growing number of RDT connections and a growing number of security threats require an IT security policy that is pro-active as well as reactive in an efficient way. The risk based approach used in setting up the security plans assesses all elements of the monitoring network, from the implemented technical solution and the assessment of the security needs and threats, up to the incident handling and lessons learned. The results of the assessments are, for each individual RDT connection, described in the technical paragraphs and annexes, including system descriptions, network plans and contact information. The principles of secure data handling as implemented in the shared Euratom /IAEA monitoring network can apply to a broad range of industrial monitoring systems, where human interaction is in general the largest security risk. (author)

Object-oriented Approach to High-level Network Monitoring and Management

Science.gov (United States)

Mukkamala, Ravi

2000-01-01

An absolute prerequisite for the management of large investigating methods to build high-level monitoring computer networks is the ability to measure their systems that are built on top of existing monitoring performance. Unless we monitor a system, we cannot tools. Due to the heterogeneous nature of the hope to manage and control its performance. In this underlying systems at NASA Langley Research Center, paper, we describe a network monitoring system that we use an object-oriented approach for the design, we are currently designing and implementing. Keeping, first, we use UML (Unified Modeling Language) to in mind the complexity of the task and the required model users' requirements. Second, we identify the flexibility for future changes, we use an object-oriented existing capabilities of the underlying monitoring design methodology. The system is built using the system. Third, we try to map the former with the latter. APIs offered by the HP OpenView system.

Concept of Complex Environmental Monitoring Network - Vardzia Rock Cut City Case Study

Science.gov (United States)

Elashvili, Mikheil; Vacheishvili, Nikoloz; Margottini, Claudio; Basilaia, Giorgi; Chkhaidze, Davit; Kvavadze, Davit; Spizzichino, Daniele; Boscagli, Franceso; Kirkitadze, Giorgi; Adikashvili, Luka; Navrozashvili, Levan

2016-04-01

Vardzia represents an unique cultural heritage monument - rock cut city, which unites architectural monument and Natural-Geological complex. Such monuments are particularly vulnerable and their restoration and conservation requires complex approach. It is curved in various layers of volcanic tuffs and covers several hectares of area, with chronologically different segments of construction. This monument, as many similar monuments worldwide, is subjected to slow but permanent process of destruction, expressed in following factors: surface weathering of rock, active tectonics (aseismic displacement along the active faults and earthquakes), interaction between lithologically different rock layers, existence of major cracks and associated complex block structure, surface rainwater runoff and infiltrated ground water, temperature variations, etc. During its lifetime, Vardzia was heavily damaged by Historical Earthquake of 1283 and only partly restored afterwards. The technological progress together with the increased knowledge about ongoing environmental processes, established the common understanding that the complex monitoring of the environment represents the essential component for resolving such a principal issues, as: Proper management and prevention of natural disasters; Modeling of environmental processes, their short and long term prognosis; Monitoring of macro and micro climate; Safe functioning and preservation of important constructions. Research Center of Cultural Heritage and Environment of Ilia State University in cooperation with Experts from ISPRA, with the funding from the State agency of Cultural Heritage, has developed a concept of Vardzia complex monitoring network. Concept of the network includes: monitoring local meteorological conditions (meteorological station), monitoring microclimate in caves (temperature and humidity in the air and rock), monitoring microtremors and ambient seismic noise in Vardzia (local strong motion network), monitoring

Large Scale Environmental Monitoring through Integration of Sensor and Mesh Networks

Directory of Open Access Journals (Sweden)

Raja Jurdak

2008-11-01

Full Text Available Monitoring outdoor environments through networks of wireless sensors has received interest for collecting physical and chemical samples at high spatial and temporal scales. A central challenge to environmental monitoring applications of sensor networks is the short communication range of the sensor nodes, which increases the complexity and cost of monitoring commodities that are located in geographically spread areas. To address this issue, we propose a new communication architecture that integrates sensor networks with medium range wireless mesh networks, and provides users with an advanced web portal for managing sensed information in an integrated manner. Our architecture adopts a holistic approach targeted at improving the user experience by optimizing the system performance for handling data that originates at the sensors, traverses the mesh network, and resides at the server for user consumption. This holistic approach enables users to set high level policies that can adapt the resolution of information collected at the sensors, set the preferred performance targets for their application, and run a wide range of queries and analysis on both real-time and historical data. All system components and processes will be described in this paper.

Large Scale Environmental Monitoring through Integration of Sensor and Mesh Networks.

Science.gov (United States)

Jurdak, Raja; Nafaa, Abdelhamid; Barbirato, Alessio

2008-11-24

Monitoring outdoor environments through networks of wireless sensors has received interest for collecting physical and chemical samples at high spatial and temporal scales. A central challenge to environmental monitoring applications of sensor networks is the short communication range of the sensor nodes, which increases the complexity and cost of monitoring commodities that are located in geographically spread areas. To address this issue, we propose a new communication architecture that integrates sensor networks with medium range wireless mesh networks, and provides users with an advanced web portal for managing sensed information in an integrated manner. Our architecture adopts a holistic approach targeted at improving the user experience by optimizing the system performance for handling data that originates at the sensors, traverses the mesh network, and resides at the server for user consumption. This holistic approach enables users to set high level policies that can adapt the resolution of information collected at the sensors, set the preferred performance targets for their application, and run a wide range of queries and analysis on both real-time and historical data. All system components and processes will be described in this paper.

Ant colony optimization and neural networks applied to nuclear power plant monitoring

International Nuclear Information System (INIS)

Santos, Gean Ribeiro dos; Andrade, Delvonei Alves de; Pereira, Iraci Martinez

2015-01-01

A recurring challenge in production processes is the development of monitoring and diagnosis systems. Those systems help on detecting unexpected changes and interruptions, preventing losses and mitigating risks. Artificial Neural Networks (ANNs) have been extensively used in creating monitoring systems. Usually the ANNs created to solve this kind of problem are created by taking into account only parameters as the number of inputs, outputs, and hidden layers. The result networks are generally fully connected and have no improvements in its topology. This work intends to use an Ant Colony Optimization (ACO) algorithm to create a tuned neural network. The ACO search algorithm will use Back Error Propagation (BP) to optimize the network topology by suggesting the best neuron connections. The result ANN will be applied to monitoring the IEA-R1 research reactor at IPEN. (author)

Ant colony optimization and neural networks applied to nuclear power plant monitoring

Energy Technology Data Exchange (ETDEWEB)

Santos, Gean Ribeiro dos; Andrade, Delvonei Alves de; Pereira, Iraci Martinez, E-mail: gean@usp.br, E-mail: delvonei@ipen.br, E-mail: martinez@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2015-07-01

A recurring challenge in production processes is the development of monitoring and diagnosis systems. Those systems help on detecting unexpected changes and interruptions, preventing losses and mitigating risks. Artificial Neural Networks (ANNs) have been extensively used in creating monitoring systems. Usually the ANNs created to solve this kind of problem are created by taking into account only parameters as the number of inputs, outputs, and hidden layers. The result networks are generally fully connected and have no improvements in its topology. This work intends to use an Ant Colony Optimization (ACO) algorithm to create a tuned neural network. The ACO search algorithm will use Back Error Propagation (BP) to optimize the network topology by suggesting the best neuron connections. The result ANN will be applied to monitoring the IEA-R1 research reactor at IPEN. (author)

Structural health monitoring using wireless sensor networks

Science.gov (United States)

Sreevallabhan, K.; Nikhil Chand, B.; Ramasamy, Sudha

2017-11-01

Monitoring and analysing health of large structures like bridges, dams, buildings and heavy machinery is important for safety, economical, operational, making prior protective measures, and repair and maintenance point of view. In recent years there is growing demand for such larger structures which in turn make people focus more on safety. By using Microelectromechanical Systems (MEMS) Accelerometer we can perform Structural Health Monitoring by studying the dynamic response through measure of ambient vibrations and strong motion of such structures. By using Wireless Sensor Networks (WSN) we can embed these sensors in wireless networks which helps us to transmit data wirelessly thus we can measure the data wirelessly at any remote location. This in turn reduces heavy wiring which is a cost effective as well as time consuming process to lay those wires. In this paper we developed WSN based MEMS-accelerometer for Structural to test the results in the railway bridge near VIT University, Vellore campus.

Long-term monitoring of blazars - the DWARF network

Science.gov (United States)

Backes, Michael; Biland, Adrian; Boller, Andrea; Braun, Isabel; Bretz, Thomas; Commichau, Sebastian; Commichau, Volker; Dorner, Daniela; von Gunten, Hanspeter; Gendotti, Adamo; Grimm, Oliver; Hildebrand, Dorothée; Horisberger, Urs; Krähenbühl, Thomas; Kranich, Daniel; Lustermann, Werner; Mannheim, Karl; Neise, Dominik; Pauss, Felicitas; Renker, Dieter; Rhode, Wolfgang; Rissi, Michael; Rollke, Sebastian; Röser, Ulf; Stark, Luisa Sabrina; Stucki, Jean-Pierre; Viertel, Gert; Vogler, Patrick; Weitzel, Quirin

The variability of the very high energy (VHE) emission from blazars seems to be connected with the feeding and propagation of relativistic jets and with their origin in supermassive black hole binaries. The key to understanding their properties is measuring well-sampled gamma-ray lightcurves, revealing the typical source behavior unbiased by prior knowledge from other wavebands. Using ground-based gamma-ray observatories with exposures limited by dark-time, a global network of several telescopes is needed to carry out fulltime measurements. Obviously, such observations are time-consuming and, therefore, cannot be carried out with the present state of the art instruments. The DWARF telescope on the Canary Island of La Palma is dedicated to monitoring observations. It is currently being set up, employing a costefficient and robotic design. Part of this project is the future construction of a distributed network of small telescopes. The physical motivation of VHE long-term monitoring will be outlined in detail and the perspective for a network for 24/7 observations will be presented.

Monitoring and Discovery for Self-Organized Network Management in Virtualized and Software Defined Networks

Science.gov (United States)

Valdivieso Caraguay, Ángel Leonardo; García Villalba, Luis Javier

2017-01-01

This paper presents the Monitoring and Discovery Framework of the Self-Organized Network Management in Virtualized and Software Defined Networks SELFNET project. This design takes into account the scalability and flexibility requirements needed by 5G infrastructures. In this context, the present framework focuses on gathering and storing the information (low-level metrics) related to physical and virtual devices, cloud environments, flow metrics, SDN traffic and sensors. Similarly, it provides the monitoring data as a generic information source in order to allow the correlation and aggregation tasks. Our design enables the collection and storing of information provided by all the underlying SELFNET sublayers, including the dynamically onboarded and instantiated SDN/NFV Apps, also known as SELFNET sensors. PMID:28362346

Monitoring and Discovery for Self-Organized Network Management in Virtualized and Software Defined Networks.

Science.gov (United States)

Caraguay, Ángel Leonardo Valdivieso; Villalba, Luis Javier García

2017-03-31

This paper presents the Monitoring and Discovery Framework of the Self-Organized Network Management in Virtualized and Software Defined Networks SELFNET project. This design takes into account the scalability and flexibility requirements needed by 5G infrastructures. In this context, the present framework focuses on gathering and storing the information (low-level metrics) related to physical and virtual devices, cloud environments, flow metrics, SDN traffic and sensors. Similarly, it provides the monitoring data as a generic information source in order to allow the correlation and aggregation tasks. Our design enables the collection and storing of information provided by all the underlying SELFNET sublayers, including the dynamically onboarded and instantiated SDN/NFV Apps, also known as SELFNET sensors.

Figures on petroleum 1981

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

This table taken out from the 1981 annual report 1981 contains an introductory remark on the reorganization of mineral oil statistics up to January 82. It is followed by the tables ranged as follows: refinery capacity and production, crude oil supply, GDR-coverings, import of petroleum products, petroleum consumption, export of petroleum products, transport, oil storage tanks, motor vehicle stock, taxes and tariffs, petroleum export trade, energy consumption and world petroleum numbers. In parts the tables contain comparative figures back to 1950.

Assessment and rationalization of water quality monitoring network: a multivariate statistical approach to the Kabbini River (India).

Science.gov (United States)

Mavukkandy, Musthafa Odayooth; Karmakar, Subhankar; Harikumar, P S

2014-09-01

The establishment of an efficient surface water quality monitoring (WQM) network is a critical component in the assessment, restoration and protection of river water quality. A periodic evaluation of monitoring network is mandatory to ensure effective data collection and possible redesigning of existing network in a river catchment. In this study, the efficacy and appropriateness of existing water quality monitoring network in the Kabbini River basin of Kerala, India is presented. Significant multivariate statistical techniques like principal component analysis (PCA) and principal factor analysis (PFA) have been employed to evaluate the efficiency of the surface water quality monitoring network with monitoring stations as the evaluated variables for the interpretation of complex data matrix of the river basin. The main objective is to identify significant monitoring stations that must essentially be included in assessing annual and seasonal variations of river water quality. Moreover, the significance of seasonal redesign of the monitoring network was also investigated to capture valuable information on water quality from the network. Results identified few monitoring stations as insignificant in explaining the annual variance of the dataset. Moreover, the seasonal redesign of the monitoring network through a multivariate statistical framework was found to capture valuable information from the system, thus making the network more efficient. Cluster analysis (CA) classified the sampling sites into different groups based on similarity in water quality characteristics. The PCA/PFA identified significant latent factors standing for different pollution sources such as organic pollution, industrial pollution, diffuse pollution and faecal contamination. Thus, the present study illustrates that various multivariate statistical techniques can be effectively employed in sustainable management of water resources. The effectiveness of existing river water quality monitoring

An Intelligent Monitoring Network for Detection of Cracks in Anvils of High-Press Apparatus.

Science.gov (United States)

Tian, Hao; Yan, Zhaoli; Yang, Jun

2018-04-09

Due to the endurance of alternating high pressure and temperature, the carbide anvils of the high-press apparatus, which are widely used in the synthetic diamond industry, are prone to crack. In this paper, an acoustic method is used to monitor the crack events, and the intelligent monitoring network is proposed to classify the sound samples. The pulse sound signals produced by such cracking are first extracted based on a short-time energy threshold. Then, the signals are processed with the proposed intelligent monitoring network to identify the operation condition of the anvil of the high-pressure apparatus. The monitoring network is an improved convolutional neural network that solves the problems that may occur in practice. The length of pulse sound excited by the crack growth is variable, so a spatial pyramid pooling layer is adopted to solve the variable-length input problem. An adaptive weighted algorithm for loss function is proposed in this method to handle the class imbalance problem. The good performance regarding the accuracy and balance of the proposed intelligent monitoring network is validated through the experiments finally.

Integrated System for Performance Monitoring of ATLAS TDAQ Network

CERN Document Server

Savu, D; The ATLAS collaboration; Martin, B; Sjoen, R; Batraneanu, S; Stancu, S

2010-01-01

The ATLAS TDAQ Network consists of three separate networks spanning four levels of the experimental building. Over 200 edge switches and 5 multi-blade chassis routers are used to interconnect 2000 processors, adding up to more than 7000 high speed interfaces. In order to substantially speed-up ad-hoc and post mortem analysis, a scalable, yet flexible, integrated system for monitoring both network statistics and environmental conditions, processor parameters and data taking characteristics was required. For successful up-to-the-minute monitoring, information from many SNMP compliant devices, independent databases and custom APIs was gathered, stored and displayed in an optimal way. Easy navigation and compact aggregation of multiple data sources were the main requirements; characteristics not found in any of the tested products, either open-source or commercial. This paper describes how performance, scalability and display issues were addressed and what challenges the project faced during development and deplo...

Monitoring groundwater: optimising networks to take account of cost effectiveness, legal requirements and enforcement realities

Science.gov (United States)

Allan, A.; Spray, C.

2013-12-01

The quality of monitoring networks and modeling in environmental regulation is increasingly important. This is particularly true with respect to groundwater management, where data may be limited, physical processes poorly understood and timescales very long. The powers of regulators may be fatally undermined by poor or non-existent networks, primarily through mismatches between the legal standards that networks must meet, actual capacity and the evidentiary standards of courts. For example, in the second and third implementation reports on the Water Framework Directive, the European Commission drew attention to gaps in the standards of mandatory monitoring networks, where the standard did not meet the reality. In that context, groundwater monitoring networks should provide a reliable picture of groundwater levels and a ';coherent and comprehensive' overview of chemical status so that anthropogenically influenced long-term upward trends in pollutant levels can be tracked. Confidence in this overview should be such that 'the uncertainty from the monitoring process should not add significantly to the uncertainty of controlling the risk', with densities being sufficient to allow assessment of the impact of abstractions and discharges on levels in groundwater bodies at risk. The fact that the legal requirements for the quality of monitoring networks are set out in very vague terms highlights the many variables that can influence the design of monitoring networks. However, the quality of a monitoring network as part of the armory of environmental regulators is potentially of crucial importance. If, as part of enforcement proceedings, a regulator takes an offender to court and relies on conclusions derived from monitoring networks, a defendant may be entitled to question those conclusions. If the credibility, reliability or relevance of a monitoring network can be undermined, because it is too sparse, for example, this could have dramatic consequences on the ability of a

A wireless smart sensor network for automated monitoring of cable tension

International Nuclear Information System (INIS)

Sim, Sung-Han; Cho, Soojin; Li, Jian; Jo, Hongki; Park, Jong-Woong; Jung, Hyung-Jo; Spencer Jr, Billie F

2014-01-01

As cables are primary load carrying members in cable-stayed bridges, monitoring the tension forces of the cables provides valuable information regarding structural soundness. Incorporating wireless smart sensors with vibration-based tension estimation methods provides an efficient means of autonomous long-term monitoring of cable tensions. This study develops a wireless cable tension monitoring system using MEMSIC’s Imote2 smart sensors. The monitoring system features autonomous operation, sustainable energy harvesting and power consumption, and remote access using the internet. To obtain the tension force, an in-network data processing strategy associated with the vibration-based tension estimation method is implemented on the Imote2-based sensor network, significantly reducing the wireless data transmission and the power consumption. The proposed monitoring system has been deployed and validated on the Jindo Bridge, a cable-stayed bridge located in South Korea. (paper)

A wireless smart sensor network for automated monitoring of cable tension

Science.gov (United States)

Sim, Sung-Han; Li, Jian; Jo, Hongki; Park, Jong-Woong; Cho, Soojin; Spencer, Billie F., Jr.; Jung, Hyung-Jo

2014-02-01

As cables are primary load carrying members in cable-stayed bridges, monitoring the tension forces of the cables provides valuable information regarding structural soundness. Incorporating wireless smart sensors with vibration-based tension estimation methods provides an efficient means of autonomous long-term monitoring of cable tensions. This study develops a wireless cable tension monitoring system using MEMSIC’s Imote2 smart sensors. The monitoring system features autonomous operation, sustainable energy harvesting and power consumption, and remote access using the internet. To obtain the tension force, an in-network data processing strategy associated with the vibration-based tension estimation method is implemented on the Imote2-based sensor network, significantly reducing the wireless data transmission and the power consumption. The proposed monitoring system has been deployed and validated on the Jindo Bridge, a cable-stayed bridge located in South Korea.

Actinides-1981

International Nuclear Information System (INIS)

1981-09-01

Abstracts of 134 papers which were presented at the Actinides-1981 conference are presented. Approximately half of these papers deal with electronic structure of the actinides. Others deal with solid state chemistry, nuclear physic, thermodynamic properties, solution chemistry, and applied chemistry

Actinides-1981

Energy Technology Data Exchange (ETDEWEB)

1981-09-01

Abstracts of 134 papers which were presented at the Actinides-1981 conference are presented. Approximately half of these papers deal with electronic structure of the actinides. Others deal with solid state chemistry, nuclear physic, thermodynamic properties, solution chemistry, and applied chemistry.

A versatile and interoperable network sensors for water resources monitoring

Science.gov (United States)

Ortolani, Alberto; Brandini, Carlo; Costantini, Roberto; Costanza, Letizia; Innocenti, Lucia; Sabatini, Francesco; Gozzini, Bernardo

2010-05-01

Monitoring systems to assess water resources quantity and quality require extensive use of in-situ measurements, that have great limitations like difficulties to access and share data, and to customise and easy reconfigure sensors network to fulfil end-users needs during monitoring or crisis phases. In order to address such limitations Sensor Web Enablement technologies for sensors management have been developed and applied to different environmental context under the EU-funded OSIRIS project (Open architecture for Smart and Interoperable networks in Risk management based on In-situ Sensors, www.osiris-fp6.eu). The main objective of OSIRIS was to create a monitoring system to manage different environmental crisis situations, through an efficient data processing chain where in-situ sensors are connected via an intelligent and versatile network infrastructure (based on web technologies) that enables end-users to remotely access multi-domain sensors information. Among the project application, one was focused on underground fresh-water monitoring and management. With this aim a monitoring system to continuously and automatically check water quality and quantity has been designed and built in a pilot test, identified as a portion of the Amiata aquifer feeding the Santa Fiora springs (Grosseto, Italy). This aquifer present some characteristics that make it greatly vulnerable under some conditions. It is a volcanic aquifer with a fractured structure. The volcanic nature in Santa Fiora causes levels of arsenic concentrations that normally are very close to the threshold stated by law, but that sometimes overpass such threshold for reasons still not fully understood. The presence of fractures makes the infiltration rate very inhomogeneous from place to place and very high in correspondence of big fractures. In case of liquid-pollutant spills (typically hydrocarbons spills from tanker accidents or leakage from house tanks containing fuel for heating), these fractures can act

Assessing the weather monitoring capabilities of cellular microwave link networks

Science.gov (United States)

Fencl, Martin; Vrzba, Miroslav; Rieckermann, Jörg; Bareš, Vojtěch

2016-04-01

Using of microwave links for rainfall monitoring was suggested already by (Atlas and Ulbrich, 1977). However, this technique attracted broader attention of scientific community only in the recent decade, with the extensive growth of cellular microwave link (CML) networks, which form the backbone of today's cellular telecommunication infrastructure. Several studies have already shown that CMLs can be conveniently used as weather sensors and have potential to provide near-ground path-integrated observations of rainfall but also humidity or fog. However, although research is still focusing on algorithms to improve the weather sensing capabilities (Fencl et al., 2015), it is not clear how to convince cellular operators to provide the power levels of their network. One step in this direction is to show in which regions or municipalities the networks are sufficiently dense to provide/develop good services. In this contribution we suggest a standardized approach to evaluate CML networks in terms of rainfall observation and to identify suitable regions for CML rainfall monitoring. We estimate precision of single CML based on its sensitivity to rainfall, i.e. as a function of frequency, polarization and path length. Capability of a network to capture rainfall spatial patterns is estimated from the CML coverage and path lengths considering that single CML provides path-integrated rain rates. We also search for suitable predictors for regions where no network topologies are available. We test our approach on several European networks and discuss the results. Our results show that CMLs are very dense in urban areas (> 1 CML/km2), but less in rural areas (online tool. In summary, our results demonstrate that CML represent promising environmental observation network, suitable especially for urban rainfall monitoring. The developed approach integrated into an open source online tool can be conveniently used e.g. by local operators or authorities to evaluate the suitability of

ZigBee wireless sensor network for environmental monitoring system

Science.gov (United States)

Chai, Shun-qi; Ji, Lei; Wu, Hong

2009-11-01

ZigBee is a new close-up, low-complexity, low-power, low data rate, low-cost wireless networking technology, mainly used for short distance wireless transmission. It is based on IEEE802.15.4 standards, thousands of tiny sensors form a network through mutual coordination to communications. This paper introduces the ZigBee wireless sensor networks in environmental monitoring applications. The hardware design, including microprocessor, data acquisition, antenna and peripheral circuits of the chips, and through software design composed ZigBee mesh network that can make data acquisition and communication. This network has low power consumption, low cost, the effective area is big, and information transfers reliable merits. And have confirmed the network's communication applicability by the Serial Com Assistant, also testified the network have very good pragmatism by the NS2 emulation the network's operation.

Vibration monitoring of EDF rotating machinery using artificial neural networks

International Nuclear Information System (INIS)

Alguindigue, I.E.; Loskiewicz-Buczak, A.; Uhrig, R.E.; Hamon, L.; Lefevre, F.

1991-01-01

Vibration monitoring of components in nuclear power plants has been used for a number of years. This technique involves the analysis of vibration data coming from vital components of the plant to detect features which reflect the operational state of machinery. The analysis leads to the identification of potential failures and their causes, and makes it possible to perform efficient preventive maintenance. Earlydetection is important because it can decrease the probability of catastrophic failures, reduce forced outgage, maximize utilization of available assets, increase the life of the plant, and reduce maintenance costs. This paper documents our work on the design of a vibration monitoring methodology based on neural network technology. This technology provides an attractive complement to traditional vibration analysis because of the potential of neural networks to operate in real-time mode and to handle data which may be distorted or noisy. Our efforts have been concentrated on the analysis and classification of vibration signatures collected by Electricite de France (EDF). Two neural networks algorithms were used in our project: the Recirculation algorithm and the Backpropagation algorithm. Although this project is in the early stages of development it indicates that neural networks may provide a viable methodology for monitoring and diagnostics of vibrating components. Our results are very encouraging

Software Defined Network Monitoring Scheme Using Spectral Graph Theory and Phantom Nodes

Science.gov (United States)

2014-09-01

networks is the emergence of software - defined networking ( SDN ) [1]. SDN has existed for the...Chapter III for network monitoring. A. SOFTWARE DEFINED NETWORKS SDNs provide a new and innovative method to simplify network hardware by logically...and R. Giladi, “Performance analysis of software - defined networking ( SDN ),” in Proc. of IEEE 21st International Symposium on Modeling, Analysis

Optimization of deformation monitoring networks using finite element strain analysis

Science.gov (United States)

Alizadeh-Khameneh, M. Amin; Eshagh, Mehdi; Jensen, Anna B. O.

2018-04-01

An optimal design of a geodetic network can fulfill the requested precision and reliability of the network, and decrease the expenses of its execution by removing unnecessary observations. The role of an optimal design is highlighted in deformation monitoring network due to the repeatability of these networks. The core design problem is how to define precision and reliability criteria. This paper proposes a solution, where the precision criterion is defined based on the precision of deformation parameters, i. e. precision of strain and differential rotations. A strain analysis can be performed to obtain some information about the possible deformation of a deformable object. In this study, we split an area into a number of three-dimensional finite elements with the help of the Delaunay triangulation and performed the strain analysis on each element. According to the obtained precision of deformation parameters in each element, the precision criterion of displacement detection at each network point is then determined. The developed criterion is implemented to optimize the observations from the Global Positioning System (GPS) in Skåne monitoring network in Sweden. The network was established in 1989 and straddled the Tornquist zone, which is one of the most active faults in southern Sweden. The numerical results show that 17 out of all 21 possible GPS baseline observations are sufficient to detect minimum 3 mm displacement at each network point.

Geophysical monitoring of the Purace volcano, Colombia

Directory of Open Access Journals (Sweden)

M. Arcila

1996-06-01

Full Text Available Located in the extreme northwestern part of the Los Coconucos volcanic chain in the Central Cordillera, the Purace is one of Colombia's most active volcanoes. Recent geological studies indicate an eruptive history of mainly explosive behavior which was marked most recently by a minor ash eruption in 1977. Techniques used to forecast the renewal of activity of volcanoes after a long period of quiescence include the monitoring of seismicity and ground deformation near the volcano. As a first approach toward the monitoring of the Purace volcano, Southwest Seismological Observatory (OSSO, located in the city of Cali, set up one seismic station in 1986. Beginning in June 1991, the seismic signals have also been transmitted to the Colombian Geological Survey (INGEOMINAS at the Volcanological and Seismological Observatory (OVS-UOP, located in the city of Popayan. Two more seismic stations were installed early in 1994 forming a minimum seismic network and a geodetic monitoring program for ground deformation studies was established and conducted by INGEOMINAS.

Implementation of Multiple Host Nodes in Wireless Sensing Node Network System for Landslide Monitoring

International Nuclear Information System (INIS)

Bin Abas, Faizulsalihin; Takayama, Shigeru

2015-01-01

This paper proposes multiple host nodes in Wireless Sensing Node Network System (WSNNS) for landslide monitoring. As landslide disasters damage monitoring system easily, one major demand in landslide monitoring is the flexibility and robustness of the system to evaluate the current situation in the monitored area. For various reasons WSNNS can provide an important contribution to reach that aim. In this system, acceleration sensors and GPS are deployed in sensing nodes. Location information by GPS, enable the system to estimate network topology and enable the system to perceive the location in emergency by monitoring the node mode. Acceleration sensors deployment, capacitate this system to detect slow mass movement that can lead to landslide occurrence. Once deployed, sensing nodes self-organize into an autonomous wireless ad hoc network. The measurement parameter data from sensing nodes is transmitted to Host System via host node and ''Cloud'' System. The implementation of multiple host nodes in Local Sensing Node Network System (LSNNS), improve risk- management of the WSNNS for real-time monitoring of landslide disaster

Implementation of Multiple Host Nodes in Wireless Sensing Node Network System for Landslide Monitoring

Science.gov (United States)

Abas, Faizulsalihin bin; Takayama, Shigeru

2015-02-01

This paper proposes multiple host nodes in Wireless Sensing Node Network System (WSNNS) for landslide monitoring. As landslide disasters damage monitoring system easily, one major demand in landslide monitoring is the flexibility and robustness of the system to evaluate the current situation in the monitored area. For various reasons WSNNS can provide an important contribution to reach that aim. In this system, acceleration sensors and GPS are deployed in sensing nodes. Location information by GPS, enable the system to estimate network topology and enable the system to perceive the location in emergency by monitoring the node mode. Acceleration sensors deployment, capacitate this system to detect slow mass movement that can lead to landslide occurrence. Once deployed, sensing nodes self-organize into an autonomous wireless ad hoc network. The measurement parameter data from sensing nodes is transmitted to Host System via host node and "Cloud" System. The implementation of multiple host nodes in Local Sensing Node Network System (LSNNS), improve risk- management of the WSNNS for real-time monitoring of landslide disaster.

A Risk-Based Multi-Objective Optimization Concept for Early-Warning Monitoring Networks

Science.gov (United States)

Bode, F.; Loschko, M.; Nowak, W.

2014-12-01

Groundwater is a resource for drinking water and hence needs to be protected from contaminations. However, many well catchments include an inventory of known and unknown risk sources which cannot be eliminated, especially in urban regions. As matter of risk control, all these risk sources should be monitored. A one-to-one monitoring situation for each risk source would lead to a cost explosion and is even impossible for unknown risk sources. However, smart optimization concepts could help to find promising low-cost monitoring network designs.In this work we develop a concept to plan monitoring networks using multi-objective optimization. Our considered objectives are to maximize the probability of detecting all contaminations and the early warning time and to minimize the installation and operating costs of the monitoring network. A qualitative risk ranking is used to prioritize the known risk sources for monitoring. The unknown risk sources can neither be located nor ranked. Instead, we represent them by a virtual line of risk sources surrounding the production well.We classify risk sources into four different categories: severe, medium and tolerable for known risk sources and an extra category for the unknown ones. With that, early warning time and detection probability become individual objectives for each risk class. Thus, decision makers can identify monitoring networks which are valid for controlling the top risk sources, and evaluate the capabilities (or search for least-cost upgrade) to also cover moderate, tolerable and unknown risk sources. Monitoring networks which are valid for the remaining risk also cover all other risk sources but the early-warning time suffers.The data provided for the optimization algorithm are calculated in a preprocessing step by a flow and transport model. Uncertainties due to hydro(geo)logical phenomena are taken into account by Monte-Carlo simulations. To avoid numerical dispersion during the transport simulations we use the

Covering the Monitoring Network: A Unified Framework to Protect E-Commerce Security

Directory of Open Access Journals (Sweden)

Lirong Qiu

2017-01-01

Full Text Available Multimedia applications in smart electronic commerce (e-commerce, such as online trading and Internet marketing, always face security in storage and transmission of digital images and videos. This study addresses the problem of security in e-commerce and proposes a unified framework to analyze the security data. First, to allocate the definite security resources optimally, we build our e-commerce monitoring model as an undirected network, where a monitored node is a vertex of the graph and a connection between vertices is an undirected edge. Moreover, we aim to find a minimal cover for the monitoring network as the optimal solution of resource allocation, which is defined as the network monitoring minimization problem (NMM. This problem is proved to be NP-hard. Second, by analyzing the latent threats, we design a novel and trusted monitoring system that can integrate incident monitoring, data analysis, risk assessment, and security warnings. This system does not touch users’ privacy data. Third, we propose a sequential model-based risk assessment method, which can predict the risk according to the text semantics. Our experimental results on web scale data demonstrate that our system is flexible enough when monitoring, which also verify the effectiveness and efficiency of our system.

The national environmental radiation monitoring network in egypt. Vol. 1

Energy Technology Data Exchange (ETDEWEB)

Morsy, M S [National Center for Nuclear Safety and Radiation Control, Atomic Energy Authority, Cairo (Egypt)

1996-03-01

Post accident environmental pollution with radionuclides occurs at accident site, and also cross borders to affect distant localities. The situation in egypt present special importance regarding its position near asian near asian and european nuclear sites, israel in east, and libya in the west. Also, the present and future nuclear installations in egypt. Environmental base line monitoring data is essential knowledge in nuclear practices. For these reasons, the egyptian government took steps to set up a national response plan for dealing with inside and outside accidents. The key elements of the plan is the establishment of a national environmental monitoring network (NERMN) and a nuclear emergency response system (NERS). The NERMN will detect radioactivity resulting from any accident affecting the egyptian territory even if it is not formally reported under international agreements, or if there are delays in notification. Therefore, the system provides the means of assembling and analyzing the radiological monitoring data related to the accident, and allowing information for the authorities. This is met with through a fully automatic system for gamma radiation monitoring and a semiautomatic system for air activity monitoring (aerosol), and network of liquid monitors. 4 figs., 1 tab.

The national environmental radiation monitoring network in egypt. Vol. 1

International Nuclear Information System (INIS)

Morsy, M.S.

1996-01-01

Post accident environmental pollution with radionuclides occurs at accident site, and also cross borders to affect distant localities. The situation in egypt present special importance regarding its position near asian near asian and european nuclear sites, israel in east, and libya in the west. Also, the present and future nuclear installations in egypt. Environmental base line monitoring data is essential knowledge in nuclear practices. For these reasons, the egyptian government took steps to set up a national response plan for dealing with inside and outside accidents. The key elements of the plan is the establishment of a national environmental monitoring network (NERMN) and a nuclear emergency response system (NERS). The NERMN will detect radioactivity resulting from any accident affecting the egyptian territory even if it is not formally reported under international agreements, or if there are delays in notification. Therefore, the system provides the means of assembling and analyzing the radiological monitoring data related to the accident, and allowing information for the authorities. This is met with through a fully automatic system for gamma radiation monitoring and a semiautomatic system for air activity monitoring (aerosol), and network of liquid monitors. 4 figs., 1 tab

Intelligent IPv6 based iot network monitoring and altering system on ...

African Journals Online (AJOL)

Intelligent IPv6 based iot network monitoring and altering system on Cooja framework. ... Journal of Fundamental and Applied Sciences. Journal Home · ABOUT THIS ... Keywords: IoT; Cooja framework; Contiki OS; packet monitoring.

The wireless sensor network monitoring system for regional environmental nuclear radiation

International Nuclear Information System (INIS)

Liu Chong; Liu Dao; Wang Yaojun; Xie Yuxi; Song Lingling

2012-01-01

The wireless sensor network (WSN) technology has been utilized to design a new regional environmental radiation monitoring system based on the wireless sensor networks to meet the special requirements of monitoring the nuclear radiation in certain regions, and realize the wireless transmission of measurement data, information processing and integrated measurement of the nuclear radiation and the corresponding environmental parameters in real time. The system can be applied to the wireless monitoring of nuclear radiation dose in the nuclear radiation environment. The measured data and the distribution of radiation dose can be vividly displayed on the graphical interface in the host computer. The system has functioned with the wireless transmission and control, the data storage, the historical data inquiry, the node remote control. The experimental results show that the system has the advantages of low power consumption, stable performance, network flexibility, range of measurement and so on. (authors)

A power supply design of body sensor networks for health monitoring of neonates

NARCIS (Netherlands)

Chen, W.; Sonntag, C.L.W.; Boesten, F.; Bambang Oetomo, S.; Feijs, L.M.G.

2008-01-01

Critically ill new born babies are extremely tiny and vulnerable to external disturbance. Non-invasive health monitoring with body sensor networks is crucial for the survival of these neonates and the quality of their life later on. A key question for health monitoring with body sensor networks is

Monitoring individual traffic flows within the ATLAS TDAQ network

CERN Document Server

Sjoen, R; Ciobotaru, M; Batraneanu, S M; Leahu, L; Martin, B; Al-Shabibi, A

2010-01-01

The ATLAS data acquisition system consists of four different networks interconnecting up to 2000 processors using up to 200 edge switches and five multi-blade chassis devices. The architecture of the system has been described in [1] and its operational model in [2]. Classical, SNMP-based, network monitoring provides statistics on aggregate traffic, but for performance monitoring and troubleshooting purposes there was an imperative need to identify and quantify single traffic flows. sFlow [3] is an industry standard based on statistical sampling which attempts to provide a solution to this. Due to the size of the ATLAS network, the collection and analysis of the sFlow data from all devices generates a data handling problem of its own. This paper describes how this problem is addressed by making it possible to collect and store data either centrally or distributed according to need. The methods used to present the results in a relevant fashion for system analysts are discussed and we explore the possibilities a...

Delay-tolerant mobile network protocol for rice field monitoring using wireless sensor networks

Science.gov (United States)

Guitton, Alexandre; Andres, Frédéric; Cardoso, Jarbas Lopes; Kawtrakul, Asanee; Barbin, Silvio E.

2015-10-01

The monitoring of rice fields can improve productivity by helping farmers throughout the rice cultivation cycle, on various issues: when to harvest, when to treat the crops against disease, when to increase the water level, how to share observations and decisions made in a collaborative way, etc. In this paper, we propose an architecture to monitor a rice field by a wireless sensor network. Our architecture is based on static sensor nodes forming a disconnected network, and mobile nodes communicating with the sensor nodes in a delay-tolerant manner. The data collected by the static sensor nodes are transmitted to mobile nodes, which in turn transmit them to a gateway, connected to a database, for further analysis. We focus on the related architecture, as well as on the energy-efficient protocols intended to perform the data collection.

Monitoring and Discovery for Self-Organized Network Management in Virtualized and Software Defined Networks

Directory of Open Access Journals (Sweden)

Ángel Leonardo Valdivieso Caraguay

2017-03-01

Full Text Available This paper presents the Monitoring and Discovery Framework of the Self-Organized Network Management in Virtualized and Software Defined Networks SELFNET project. This design takes into account the scalability and flexibility requirements needed by 5G infrastructures. In this context, the present framework focuses on gathering and storing the information (low-level metrics related to physical and virtual devices, cloud environments, flow metrics, SDN traffic and sensors. Similarly, it provides the monitoring data as a generic information source in order to allow the correlation and aggregation tasks. Our design enables the collection and storing of information provided by all the underlying SELFNET sublayers, including the dynamically onboarded and instantiated SDN/NFV Apps, also known as SELFNET sensors.

Sleep Scheduling in Critical Event Monitoring with Wireless Sensor Networks

NARCIS (Netherlands)

Guo, Peng; Jiang, Tao; Zhang, Qian; Zhang, Kui

In this paper, we focus on the applications of wireless sensor networks (WSNs) for critical event monitoring, where normally there are only small number of packets need to be transmitted, while when urgent event occurs, the alarm should be broadcast to the entire network as soon as possible. During

On a digital wireless impact-monitoring network for large-scale composite structures

International Nuclear Information System (INIS)

Yuan, Shenfang; Mei, Hanfei; Qiu, Lei; Ren, Yuanqiang

2014-01-01

Impact, which may occur during manufacture, service or maintenance, is one of the major concerns to be monitored throughout the lifetime of aircraft composite structures. Aiming at monitoring impacts online while minimizing the weight added to the aircraft to meet the strict limitations of aerospace engineering, this paper puts forward a new digital wireless network based on miniaturized wireless digital impact-monitoring nodes developed for large-scale composite structures. In addition to investigations on the design methods of the network architecture, time synchronization and implementation method, a conflict resolution method based on the feature parameters of digital sequences is first presented to address impact localization conflicts when several nodes are arranged close together. To verify the feasibility and stability of the wireless network, experiments are performed on a complex aircraft composite wing box and an unmanned aerial vehicle (UAV) composite wing. Experimental results show the successful design of the presented network. (paper)

Novel method for fog monitoring using cellular networks infrastructures

Science.gov (United States)

David, N.; Alpert, P.; Messer, H.

2012-08-01

A major detrimental effect of fog is visibility limitation which can result in serious transportation accidents, traffic delays and therefore economic damage. Existing monitoring techniques including satellites, transmissometers and human observers - suffer from low spatial resolution, high cost or lack of precision when measuring near ground level. Here we show a novel technique for fog monitoring using wireless communication systems. Communication networks widely deploy commercial microwave links across the terrain at ground level. Operating at frequencies of tens of GHz they are affected by fog and are, effectively, an existing, spatially world-wide distributed sensor network that can provide crucial information about fog concentration and visibility. Fog monitoring potential is demonstrated for a heavy fog event that took place in Israel. The correlation between transmissomters and human eye observations to the visibility estimates from the nearby microwave links was found to be 0.53 and 0.61, respectively. These values indicate the high potential of the proposed method.

Energy Efficient Monitoring for Intrusion Detection in Battery-Powered Wireless Mesh Networks

KAUST Repository

Hassanzadeh, Amin

2011-07-18

Wireless Mesh Networks (WMN) are easy-to-deploy, low cost solutions for providing networking and internet services in environments with no network infrastructure, e.g., disaster areas and battlefields. Since electric power is not readily available in such environments battery-powered mesh routers, operating in an energy efficient manner, are required. To the best of our knowledge, the impact of energy efficient solutions, e.g., involving duty-cycling, on WMN intrusion detection systems, which require continuous monitoring, remains an open research problem. In this paper we propose that carefully chosen monitoring mesh nodes ensure continuous and complete detection coverage, while allowing non-monitoring mesh nodes to save energy through duty-cycling. We formulate the monitoring node selection problem as an optimization problem and propose distributed and centralized solutions for it, with different tradeoffs. Through extensive simulations and a proof-of-concept hardware/software implementation we demonstrate that our solutions extend the WMN lifetime by 8%, while ensuring, at the minimum, a 97% intrusion detection rate.

Ethical Decision-Making: The Role of Self-Monitoring, Future Orientation, and Social Networks

Directory of Open Access Journals (Sweden)

Ana Carla Bon

2017-02-01

Full Text Available This study examines the influence of individual factors (self monitoring, temporal orientation on social networking, and their relationship with unethical decision-making. The study used surveys to measure the unethical intentions and social network data of 129 professionals. Data were analyzed using confirmatory factor analysis and structural equation modeling. The findings provided evidence that individual factors influence the development of social networks and, along with self-monitoring, the likelihood of unethical decision-making. In particular, being in positions of lower network centrality increased individuals’ risk of unethical intention. One explanation stems from the need for high situation control to reduce risk and ensure the success of an event, which only a closed network can provide. However, ethical low self-monitor women were also found to have low centrality, so social networks alone do not explain ethical decision-making. This research represents a step forward in our understanding of ethical decision-making through the adoption of multiple and simultaneous factors, proposing an integrated theory of individual and situational factors influencing unethical options.

Fourteenth annual report radiation exposures for DOE and DOE contractor employees - 1981

International Nuclear Information System (INIS)

1983-03-01

All Department of Energy (DOE) and DOE contractors are required by DOE Order 5484.1, Chapter IV, to submit occupational exposure records to a central repository. The data required includes a summary of whole-body exposures to ionizing radiation, a summary of internal depositions of radioactive materials above specified limits, and occupational exposure reports for terminating employees. This report is a summary of the data submitted by DOE and DOE contractors for 1981. A total of 82,873 DOE and DOE contractor employees were monitored for whole-body ionizing radiation exposures in 1981. In addition to the employees, 84,343 visitors were monitored. Of all employees monitored, 54.43% received a dose equivalent that was less than measurable, 44.04% a measurable exposure less than 1 rem, and 1.53% an exposure granter than 1 rem. the exposure received by 88.14% of the visitors to DOE facilities was less than measurable. Only 11.85% of the visitors received a measurable exposure less than 1 rem, and 0.0% of the visitors received an exposure greater than 1 rem. No employees or visitors received a dose equivalent greater than 5 rem. The collective dose equivalent for DOE and DOE contractors employees was 6,902 person-rem. The collective dose equivalent for visitors was 579 person-rem. The total dose equivalent for employees and visitors combined was 7,481 person-rem. The average dose equivalent for all individuals (employees and visitors) monitored was 45 mrem and the average dose equivalent for all individuals who received a measurable exposure was 157 mrem. The highest average dose equivalent was observed for employees monitored at fuel processing facilities (342 mrem) and the lowest among visitors (7 mrem) to DOE facilities. These averages are significantly less than the DOE 5-rem/year radiation protection standard for whole-body exposures

Wireless Sensing Node Network Management for Monitoring Landslide Disaster

International Nuclear Information System (INIS)

Takayama, S; Akiyama, J; Fujiki, T; Mokhtar, N A B

2013-01-01

This paper shows the network management and operation to monitor landslide disaster at slop of mountain and hill. Natural disasters damage a measuring system easily. It is necessary for the measuring system to be flexible and robust. The measuring network proposed in this paper is the telemetry system consisted of host system (HS) and local sensing nodes network system (LSNNS). LSNNS operates autonomously and sometimes is controlled by commands from HS. HS collects data/information of landslide disaster from LSNNS, and controls LSNNS remotely. HS and LSNNS are communicated by using 'cloud' system. The dual communication is very effective and convenient to manage a network system operation

Rockwell Hanford Operations effluents and solid waste burials during calendar year 1986

International Nuclear Information System (INIS)

Howe, D.B.; Aldrich, R.C.; Shay, R.S.; Voigt, L.J.

1987-07-01

The quantities of solid, liquid, or gaseous wastes buried or discharged during calendar year 1986 are monitored and reported in this document. Discharge concentrations were compared to more restrictive Rockwell administrative control values for compliance; two gaseous streams and two liquid streams exceeded Rockwell limits. 24 refs., 3 figs., 15 tabs

National Environmental Radiation Warning And Monitoring Network And Proposed Radiation Monitoring Programme For The 1st Nuclear Power Plant Ninth Thuan

International Nuclear Information System (INIS)

Vuong Thu Bac

2011-01-01

National Environmental Radiation Warning and Monitoring Network has been gradually setting up based on some of legislative documents which have been issued in recent years. Studies and surveys to build an environmental radiation monitoring program for nuclear power plant (NPP) have also been implemented. This paper aims to introduce National Environmental Radiation Warning and Monitoring Network in Vietnam which has been approved by the government, the draft program for environmental radiation monitoring Ninh Thuan NPP and some initial results of research about environmental radiation in the planning area for building first NPP in Vietnam. (author)

1986 CERN School of Computing

International Nuclear Information System (INIS)

Verkerk, C.

1987-01-01

These proceedings contain written versions of lectures delivered at the 1986 CERN School of Computing. Two lecture series treated trends in computer architecture and architectural requirements for high-energy physics. Three other courses concentrated on object-oriented programming, on objects in Ada, and on modularization and re-usability. Expert systems, their applications, and knowledge engineering for graphics were treated by three lectures. The programme of the School covered, in addition, practical aspects of networks, buses for high-energy physics, the design of data-acquisition systems, and examples of on-line systems for particle physics experiments. Optical storage methods, software for distributed systems, symbolic formula manipulation, and solid modelling and rendering were also covered. Experience with transputers was the subject of an unscheduled presentation. (orig.)

Towards A New Opportunistic IoT Network Architecture for Wildlife Monitoring System

NARCIS (Netherlands)

Ayele, Eyuel Debebe; Meratnia, Nirvana; Havinga, Paul J.M.

In this paper we introduce an opportunistic dual radio IoT network architecture for wildlife monitoring systems (WMS). Since data processing consumes less energy than transmitting the raw data, the proposed architecture leverages opportunistic mobile networks in a fixed LPWAN IoT network

Final Treatability Study in Support of Remediation by Natural Attenuation Site FT-1 at Fairchild Air Force Base, Spokane, Washington

Science.gov (United States)

1997-10-01

aquifer: Ground Water Monitoring Review, Winter, 1987, p. 64-71. Bartha , R., 1986, Biotechnology of petroleum pollutant biodegradation: Microbial Ecology ...trichloroethylene by the ammonia-oxidizing bacterium Nitrosomonas europaea: Biochem. Biophys. Res. Commun., vol. 159, p. 640-643. Atlas , R.M., 1981, Microbial ...role of electron donor for microbial metabolism and are completely degraded or detoxified (Bouwer, 1992). Electron acceptors are elements or

Ural-Tweed Bighorn Sheep Wildlife Mitigation Project, 1986 Annual Report.

Energy Technology Data Exchange (ETDEWEB)

Yde, Chris A. (Montana Department of Fish, Wildlife and Parks, Helena, MT); Summerfield, Bob; Young, Lewis (Kootenai National Forest, Libby, MT)

1987-02-01

This report summarizes the results of the project activities from September 1, 1984 to December 31, 1986. To date, habitat treatments have been initiated on eight areas. The treatments include selective slash and burn, prescribed fire and fertilization. Inclement weather precluded the completion of the prescribed burns scheduled during fall 1985 and fall 1986. The lower Stonehill prescribed fire was rescheduled from fall 1985 to spring 1986 with the burn accomplished, producing varied results. Extensive pretreatment vegetative information has been collected from all units scheduled for habitat manipulations. Additionally, future projects have been delineated for other areas frequented by bighorn sheep. Ten adult bighorn sheep (5 ewes and 5 rams) have been fitted with radio transmitters. Systematic aerial and ground surveys were utilized to monitor the movements and seasonal habitat preferences of the instrumented sheep. Age and sex information was gathered whenever possible to aid in the development of a population model, Monthly pallet group collections were initiated in May 1985 to provide samples for 2.6 diaminopimetic acid (DAPA), food habits and lungworm larvae analysis. The majority of the data analysis is ongoing and will be presented in later reports.

Progress report 1981

International Nuclear Information System (INIS)

1982-01-01

Presented are the research works carried out in 1981 in Physics, Chemistry, Nuclear Agriculture, Health Physics, Electronics Division and Nuclear Information group of Ankara Nuclear Research and Training Center. (author)

Monitoring of bird abundance and distribution at McKinley Bay and Hutchison Bay, Northwest Territories, 1981 to 1993

Energy Technology Data Exchange (ETDEWEB)

Cornish, B J; Dickson, D L

1994-04-01

McKinley Bay has been identified as a preferred site for a harbor to support oil and gas production in the Beaufort Sea. As the bay is a molting area for several species of diving duck, a study was initiated to monitor the effect of harbor development on birds using the bay. Baseline information on the natural annual fluctuations in the number of birds were collected for nine years at McKinley Bay and eight years at neighboring Hutchinson Bay, an area chosen as the control. The final report of the predevelopment phase of the monitoring study is presented, including results of the 1993 surveys and a summary of results of all years of surveys. There were significantly more diving ducks in McKinley Bay in early August 1990 to 1993, on average, than from 1981 to 1985. No statistically significant change in total diving ducks was noted at Hutchinson Bay. Numbers of species of divers varied substantially between years at the two bays but not to the same degree. Significantly more Pacific loons, red-throated loons, and northern pintails were recorded in the 1990-1993 surveys at McKinley Bay than in earlier surveys. Potential explanations for the large between-year fluctuations in diving duck numbers are discussed. The variations may be due to bird responses to changes in the physical environment or related to the limitations of the aerial survey techniques used. Because of the large natural fluctuations in numbers of molting diving ducks using these bays in early August, it will be difficult to detect future impacts of industrial disturbance, even when sources of survey bias are minimized. It is concluded that aerial surveys of molting diving ducks in the two bays are unsuitable for monitoring the effects of industrial development. 41 refs., 7 figs., 23 tabs.

Recent Developments on Wireless Sensor Networks Technology for Bridge Health Monitoring

Directory of Open Access Journals (Sweden)

Guang-Dong Zhou

2013-01-01

Full Text Available Structural health monitoring (SHM systems have shown great potential to sense the responses of a bridge system, diagnose the current structural conditions, predict the expected future performance, provide information for maintenance, and validate design hypotheses. Wireless sensor networks (WSNs that have the benefits of reducing implementation costs of SHM systems as well as improving data processing efficiency become an attractive alternative to traditional tethered sensor systems. This paper introduces recent technology developments in the field of bridge health monitoring using WSNs. As a special application of WSNs, the requirements and characteristics of WSNs when used for bridge health monitoring are firstly briefly discussed. Then, the state of the art in WSNs-based bridge health monitoring systems is reviewed including wireless sensor, network topology, data processing technology, power management, and time synchronization. Following that, the performance validations and applications of WSNs in bridge health monitoring through scale models and field deployment are presented. Finally, some existing problems and promising research efforts for promoting applications of WSNs technology in bridge health monitoring throughout the world are explored.

Re-evaluation of the effectiveness of the central A/M Area recovery well network

International Nuclear Information System (INIS)

Haselow, J.S.

1991-06-01

A groundwater recovery well network has been operating in the central portion of the A/M Area of the Savannah River Site (SRS) since 1985 to retrieve chlorinated volatile organic solvents. In 1986, a groundwater modeling study was performed to evaluate the effectiveness of the recovery well network that included planned recovery wells (RWM 1 through 11) and process water wells (S. S. Papadopulous, 1986). Since the original modeling study, use of some of the process wells has discontinued and some pumping rates at other wells have changed. Also, the understanding of the hydrologic system in the A/M Area has improved because additional monitoring wells have been installed in the area. As a result, an updated groundwater flow model (Beaudoin et al., 1991) for the area was used to evaluate the effectiveness of the existing recovery network. The results of this study indicate that the estimated effectiveness of the recovery well has not changed dramatically since the original groundwater modeling study. However, slight differences do exist between the original study and this study because the recent model more accurately reflects the A/M Area subsurface hydrologic system

Wireless body sensor networks for health-monitoring applications

International Nuclear Information System (INIS)

Hao, Yang; Foster, Robert

2008-01-01

Current wireless technologies, such as wireless body area networks and wireless personal area networks, provide promising applications in medical monitoring systems to measure specified physiological data and also provide location-based information, if required. With the increasing sophistication of wearable and implantable medical devices and their integration with wireless sensors, an ever-expanding range of therapeutic and diagnostic applications is being pursued by research and commercial organizations. This paper aims to provide a comprehensive review of recent developments in wireless sensor technology for monitoring behaviour related to human physiological responses. It presents background information on the use of wireless technology and sensors to develop a wireless physiological measurement system. A generic miniature platform and other available technologies for wireless sensors have been studied in terms of hardware and software structural requirements for a low-cost, low-power, non-invasive and unobtrusive system. (topical review)

IPv6-Based Smart Metering Network for Monitoring Building Electricity

Directory of Open Access Journals (Sweden)

Dong Xu

2013-01-01

Full Text Available A smart electricity monitoring system of building is presented using ZigBee and internet to establish the network. This system consists of three hardware layers: the host PC, the router, and the sensor nodes. A hierarchical ant colony algorithm is developed for data transmission among the wireless sensor nodes. The wireless communication protocol is also designed based on IPv6 protocol on IEEE 802.15.4 wireless network. All-IP approach and peer-to-peer mode are integrated to optimize the network building. Each node measures the power, current, and voltage and transmits them to the host PC through the router. The host software is designed for building test characteristics, having a tree hierarchy and a friendly interface for the user. The reliability and accuracy of this monitoring system are verified in the experiment and application.

Royal Decree-Law 1302/1986 of 28 June 1986 on environmental impact studies

International Nuclear Information System (INIS)

1986-01-01

This Royal Decree-Law (No 1302/1986) of 28th June 1986 was published in the Official Gazette of 30th June 1986. The purpose of this Decree-Law is to provide for assessments of the environmental impact of certain projected installations and activities. The installations and activities requiring environmental impact studies are listed in the Annex to the Decree-Law and include nuclear power plants and other nuclear reactors (excluding those whose thermal power does not exceed 1 kW) as well as installations for the disposal and final storage of radioactive waste (NEA) [fr

An Integrated Environment Monitoring System for Underground Coal Mines—Wireless Sensor Network Subsystem with Multi-Parameter Monitoring

OpenAIRE

Zhang, Yu; Yang, Wei; Han, Dongsheng; Kim, Young-Il

2014-01-01

Environment monitoring is important for the safety of underground coal mine production, and it is also an important application of Wireless Sensor Networks (WSNs). We put forward an integrated environment monitoring system for underground coal mine, which uses the existing Cable Monitoring System (CMS) as the main body and the WSN with multi-parameter monitoring as the supplementary technique. As CMS techniques are mature, this paper mainly focuses on the WSN and the interconnection between t...

The Emergence of a Transnational Advocacy Network: International Election Monitoring in the Philippines, Chile, Nicaragua, and Mexico

Directory of Open Access Journals (Sweden)

Arturo Santa Cruz

2004-08-01

Full Text Available In this paper I question the existence of a global civil society, suggesting that what we have witnessed in recent years is the emergence of myriad transnational advocacy networks (TANs. I illustrate this claim by looking at a recently novel area in world politics: the international monitoring of elections (IEM, a practice which I claim has partially redefined state sovereignty. This paper takes form as follows. In the first section I present a conceptual discussion on world civil society and TANS , and suggest an unexplored way in which emergent norms might be adopted internationally. In the next four sections I follow the evolution of the IEM TAN. Thus, the second section deals with the foundational 1986 Philippine case; the third section with the 1988 Chilean plebiscite; the fourth with the 1990 Nicaraguan elections, and the fifth with the 1994 Mexican electoral process. I conclude in the sixth section by evaluating the usefulness of the path of norm-diffusion, and by discussing how the practice of non-state actors has contributed to the redefinition of both state sovereignty and the international system.

Dose rate mapping and quantitative analysis of radioactive deposition with simple monitoring instruments in Finland after the Chernobyl accident.

Energy Technology Data Exchange (ETDEWEB)

Koivukoski, J. [Ministry of the Interior, Rescue Dept., Helsinki (Finland); Paatero, J. [Finnish Meteorological Inst., Helsinki (Finland)], E-mail: janne.koivukoski@intermin.fi

2013-03-01

This article reviews the Finnish dose-rate mapping equipment and the system to process the obtained results, which were used immediately after the 1986 Chernobyl accident. We present the results of the external gamma-radiation monitoring carried out with simple civil-defence gamma monitoring instruments and compare them with the subsequent deposition mapping performed with research-grade instruments. The analysis shows that the quality of radiation mapping is good enough for decision makers to direct protective measures to the right areas. This review also demonstrates that a simple stationary external gamma radiation monitoring network can be effectively used for early warning in radiation emergency situations. (orig.)

Study of passive optical network monitoring based on non-OTDR

Science.gov (United States)

Li, Chuan-qi; Wang, Da-chi; Hu, Jin-lin

2014-03-01

Aiming at the defects of passive optical network (PON) monitoring based on optical time domain reflectometry (OTDR) technology, we research the non-OTDR monitoring technology. The coding scheme based on periodic encoder monitoring is discussed, and its limitation is analyzed. On this basis, the monitoring technology based on optical code division multiple access (OCDMA) is put forward. We analyze the feasibility of monitoring scheme based on PON of OCDMA, design a monitoring plan, and then use OptiSystem to simulate the design. The results of simulation and bit error rate (BER) analysis show that this monitoring technology can overcome the deficiencies of OTDR and distinguish the monitoring signals of different fiber branches clearly, which meets the demands for high beam split ratio of multi-user communication.

The Canarian Seismic Monitoring Network: design, development and first result

Science.gov (United States)

D'Auria, Luca; Barrancos, José; Padilla, Germán D.; García-Hernández, Rubén; Pérez, Aaron; Pérez, Nemesio M.

2017-04-01

Tenerife is an active volcanic island which experienced several eruptions of moderate intensity in historical times, and few explosive eruptions in the Holocene. The increasing population density and the consistent number of tourists are constantly raising the volcanic risk. In June 2016 Instituto Volcanologico de Canarias started the deployment of a seismological volcano monitoring network consisting of 15 broadband seismic stations. The network began its full operativity in November 2016. The aim of the network are both volcano monitoring and scientific research. Currently data are continuously recorded and processed in real-time. Seismograms, hypocentral parameters, statistical informations about the seismicity and other data are published on a web page. We show the technical characteristics of the network and an estimate of its detection threshold and earthquake location performances. Furthermore we present other near-real time procedures on the data: analysis of the ambient noise for determining the shallow velocity model and temporal velocity variations, detection of earthquake multiplets through massive data mining of the seismograms and automatic relocation of events through double-difference location.

Experimental validation of concept for real-time wavelength monitoring and tracking in densely populated WDM networks

Science.gov (United States)

Vukovic, Alex; Savoie, Michel; Hua, Heng; Campbell, Scott; Nguyen, Thao

2005-10-01

As the telecom industry responds with technological innovations to requests for higher data rates, increased number of wavelengths at higher densities, longer transmission distances and more intelligence for next generation optical networks, new monitoring schemes based on monitoring and tracking of each wavelength need to be developed and deployed. An optical layer monitoring scheme, based on tracking key optical parameters per each wavelength, is considered to be one of enablers for the transformation of today's opaque networks to dynamic, agile future networks. Ever-tighter network monitoring and control will be required to fulfill customer Service Level Agreements (SLAs). A wavelength monitoring and tracking concept was developed as a three-step approach. It started with the identification of all critical parameters required to obtain sufficient information about each wavelength; followed by the deployment of a cost-efficient device to provide simultaneous, accurate measurements in real-time of all critical parameters; and finally, the formulation of a specification for wavelength monitoring and tracking devices for real-time, simultaneous measurements and processing the data. A prototype solution based on a commercially available integrated modular spectrometer within a testbed environment associated with the all-optical network (AON) demonstrator program was used to verify and validate the wavelength monitoring and tracking concept. The developed concept verified that it can manage tracking of 32 wavelengths within a wavelength division multiplexing network. The developed concept presented in this paper can be used inside the transparent domains of networks to detect, identify and locate signal degradations in real-time, even sometimes to recognize the cause of the failure. Aside from the reduction of operational expenses due to the elimination of the need for operators at every site and skilled field technicians to isolate and repair faults, the developed

Progress report 1981

International Nuclear Information System (INIS)

The activities of the laboratory during 1981 are briefly reported in high energy physics: neutrinos interactions, quark fusion in hadron interactions, photon interactions at high energy, instrumentation needed for new research programs [fr

Wearable and Implantable Wireless Sensor Network Solutions for Healthcare Monitoring

OpenAIRE

Darwish, Ashraf; Hassanien, Aboul Ella

2011-01-01

Wireless sensor network (WSN) technologies are considered one of the key research areas in computer science and the healthcare application industries for improving the quality of life. The purpose of this paper is to provide a snapshot of current developments and future direction of research on wearable and implantable body area network systems for continuous monitoring of patients. This paper explains the important role of body sensor networks in medicine to minimize the need for caregivers ...

Meningen over abortus in West-Europa, 1981-2000 [Abortion attitudes in Western Europe, 1981-2000

OpenAIRE

Need, A.; Ultee, W.C.; Levels, M.; Tienen, M. van

2008-01-01

Summary Abortion attitudes in Western Europe, 1981-2000 This article answers descriptive and explanatory questions about abortion attitudes in Western Europe between 1981 and 2000. It explains country differences and trends in these attitudes with abortion laws of states, with the norms that prevail in churches and schools, and with opinions and behaviour of others in a society. Using the European and World Value Surveys, complemented with abortion statistics and information about abortion la...

Site 300 hazardous-waste-assessment project. Interim report: December 1981. Preliminary site reconnaissance and project work plan

International Nuclear Information System (INIS)

Raber, E.; Helm, D.; Carpenter, D.; Peifer, D.; Sweeney, J.

1982-01-01

This document was prepared to outline the scope and objectives of the Hazardous Waste Assessment Project (HWAP) at Site 300. This project was initiated in October, 1981, to investigate the existing solid waste landfills in an effort to satisfy regulatory guidelines and assess the potential for ground-water contamination. This involves a site-specific investigation (utilizing geology, hydrology, geophysics and geochemistry) with the goal of developing an effective ground-water quality monitoring network. Initial site reconnaissance work has begun and we report the results, to date, of our geologic hydrogeologic studies. All known solid waste disposal locations are underlain by rocks of either the Late Miocene Neroly Formation or the Cierbo Formation, both of which are dominantly sandstones interbedded with shale and claystone. The existence of a regional confined (artesian) aquifer, as well as a regional water-table aquifer is postulated for Site 300. Preliminary analysis has led to an understanding of directions and depths of regional ground-water flow

Extending unified-theory-of-reinforcement neural networks to steady-state operant behavior.

Science.gov (United States)

Calvin, Olivia L; McDowell, J J

2016-06-01

The unified theory of reinforcement has been used to develop models of behavior over the last 20 years (Donahoe et al., 1993). Previous research has focused on the theory's concordance with the respondent behavior of humans and animals. In this experiment, neural networks were developed from the theory to extend the unified theory of reinforcement to operant behavior on single-alternative variable-interval schedules. This area of operant research was selected because previously developed neural networks could be applied to it without significant alteration. Previous research with humans and animals indicates that the pattern of their steady-state behavior is hyperbolic when plotted against the obtained rate of reinforcement (Herrnstein, 1970). A genetic algorithm was used in the first part of the experiment to determine parameter values for the neural networks, because values that were used in previous research did not result in a hyperbolic pattern of behavior. After finding these parameters, hyperbolic and other similar functions were fitted to the behavior produced by the neural networks. The form of the neural network's behavior was best described by an exponentiated hyperbola (McDowell, 1986; McLean and White, 1983; Wearden, 1981), which was derived from the generalized matching law (Baum, 1974). In post-hoc analyses the addition of a baseline rate of behavior significantly improved the fit of the exponentiated hyperbola and removed systematic residuals. The form of this function was consistent with human and animal behavior, but the estimated parameter values were not. Copyright © 2016 Elsevier B.V. All rights reserved.

Establishment of a hydrological monitoring network in a tropical African catchment: An integrated participatory approach

Science.gov (United States)

Gomani, M. C.; Dietrich, O.; Lischeid, G.; Mahoo, H.; Mahay, F.; Mbilinyi, B.; Sarmett, J.

Sound decision making for water resources management has to be based on good knowledge of the dominant hydrological processes of a catchment. This information can only be obtained through establishing suitable hydrological monitoring networks. Research catchments are typically established without involving the key stakeholders, which results in instruments being installed at inappropriate places as well as at high risk of theft and vandalism. This paper presents an integrated participatory approach for establishing a hydrological monitoring network. We propose a framework with six steps beginning with (i) inception of idea; (ii) stakeholder identification; (iii) defining the scope of the network; (iv) installation; (v) monitoring; and (vi) feedback mechanism integrated within the participatory framework. The approach is illustrated using an example of the Ngerengere catchment in Tanzania. In applying the approach, the concept of establishing the Ngerengere catchment monitoring network was initiated in 2008 within the Resilient Agro-landscapes to Climate Change in Tanzania (ReACCT) research program. The main stakeholders included: local communities; Sokoine University of Agriculture; Wami Ruvu Basin Water Office and the ReACCT Research team. The scope of the network was based on expert experience in similar projects and lessons learnt from literature review of similar projects from elsewhere integrated with local expert knowledge. The installations involved reconnaissance surveys, detailed surveys, and expert consultations to identify best sites. First, a Digital Elevation Model, land use, and soil maps were used to identify potential monitoring sites. Local and expert knowledge was collected on flow regimes, indicators of shallow groundwater plant species, precipitation pattern, vegetation, and soil types. This information was integrated and used to select sites for installation of an automatic weather station, automatic rain gauges, river flow gauging stations

Geo mathematic tools for the design of a radioisotopes monitoring network in order to modelling the groundwater dynamics processes and hydrodynamic management; Empleo de herramientas geomatematicas para el disenno de una red de Monitoreo radioisotopico en el modelaje hidrodinamico de un Recurso hidrico complejo

Energy Technology Data Exchange (ETDEWEB)

Peralta, J L; Gil, R; Leyva, D [Centro de Proteccion e Higiene de las Radiaciones, La Habana (Cuba); Molerio, L F [Instituto de Geofisica y Astronomia IGA, La Habana (Cuba); Pin, M [Empresa de Aguas de la Habana, La Habana (Cuba)

2004-07-01

The present paper, shows the application of geo mathematic tools [Mangin,1981; Molerio,1997] for the design of a radioisotopes monitoring network in order to modelling the groundwater dynamics processes and hydrodynamic management of a Karstic Basin (Almendares-Vento watershed), which is very difficult to evaluate due to the physical-geographical, geologic and hydrogeological characteristics. The Almendares Vento watershed (AVW) is close to the Jaruco-Aguacate watershed, with a similar hydrogeologic and geologic structure, therefore similar result must be expected. In the AVW case is necessary to identify, with more precision, the water propagation limits of the stratified layers according to the waters transit times, recharges and dynamics aquifers, residence time, groundwater contamination and the groundwater-surface water interaction due to the dam placed on the basin. The paper allowed the identification of a monitoring points network, taking into account, between other statistical approaches, the good correlation, the high memory effect, etc. According to the analysis of the variances spectral, have been obtained and optimized the sampling frequency of the network points in the Basin. Besides, it have been identified the necessities to include the detailed evaluation of a specific point of the network in the hydrodynamic study (Vento watershed). In order to evaluate the optimization of the designed monitoring network, the geo mathematic study developed was compared with the results of the mathematical model AQUIMPE, the final result showed the validation of the obtained design. The results of the work allow the best monitoring of the parameters in order to determine the aquifer recharge, residence times, the vulnerability to the waters contamination and the groundwater-surface water interaction.

Research overview of real-time monitoring system for micro leak of three-dimensional pipe network

Directory of Open Access Journals (Sweden)

Shaofeng WANG

2016-04-01

Full Text Available Aiming at the key technical problems encountered by domestic and foreign scholars in building the real-time monitoring system for the micro leak of three-dimensional pipe networks, the paper classifies the problems into three aspects: 1 in the extraction of fault signal frequency, how to avoid the effect of the mixed echo stack and improve the delay estimation accuracy of the correlation; 2 in network bifurcation structure, how to discern the signal propagation path, and how to locate the leak source; 3 under the uncertainly delay in transmitting and receiving information data, how to ensure the time synchronization accuracy of the real-time monitoring system for the three-dimensional pipe network leakage. Through the comparison of the monitoring technologies for the pipe network leakage at home and abroad, it shows that the acoustic emission sensor network based three-dimensional pipeline leak real-time monitoring has great advantages in detecting the weak leakage of flammable and explosive gas/liquid transportation pipelines.

Development of network communication function for digitalized neutron flux monitoring instrument

International Nuclear Information System (INIS)

Li Kai; Zhang Liangju; Chen Xiaojun; Li Baoxiang

2002-01-01

It is essential for a digitalized Neutron Flux Monitoring Instrument to communicate with other parts of Instrumentation and Control System in a network environment, and it is fairly different from the case of traditional analogue nuclear instrumentation. How to satisfy all the requirements of different network structure and communication protocol, which might be adopted in different target nuclear power plant, is a key issue in the design and development of a digitalized neutron flux monitoring instrument. The author describes the overall communication scheme, mainly discusses the design idea and the requirements of the communication interfaces and the implementation of the RS-485 interface as an example of the digitalized neutron flux monitoring instrument, which is under development in the institute

Network Traffic Monitoring Using Poisson Dynamic Linear Models

Energy Technology Data Exchange (ETDEWEB)

Merl, D. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2011-05-09

In this article, we discuss an approach for network forensics using a class of nonstationary Poisson processes with embedded dynamic linear models. As a modeling strategy, the Poisson DLM (PoDLM) provides a very flexible framework for specifying structured effects that may influence the evolution of the underlying Poisson rate parameter, including diurnal and weekly usage patterns. We develop a novel particle learning algorithm for online smoothing and prediction for the PoDLM, and demonstrate the suitability of the approach to real-time deployment settings via a new application to computer network traffic monitoring.

Optimisation of the German moss monitoring network; Optimierung des Moosmonitoring-Messnetzes in Deutschland

Energy Technology Data Exchange (ETDEWEB)

Pesch, R.; Schroeder, W. [Hochschule Vechta (Germany). Lehrstuhl fuer Landschaftsoekologie; Dieffenbach-Fries, H. [Umweltbundesamt, Langen (Germany). Fachgebiet II 5.4; Genssler, L. [Landesamt fuer Natur, Umwelt und Verbraucherschutz Nordrhein-Westfalen, Recklinghausen (Germany)

2008-02-15

Germany participated in the Europen Heavy Metals in Mosses Surveys 1990, 1995 and 2000. The goal was to map the spatial distribution of the metal accumulation as a comparative measure for the metal deposition in terrestrial ecosystems. In the campaign in 2005, additionally nitrogen was monitored for the first time. It should be investigated how the monitoring network could be reduced from 1028 to 720 sites without any significant influence on chosen statistical criteria. Furthermore, the new network should be linked to other environmental monitoring programmes. (orig.)

A Unified Monitoring Framework for Energy Consumption and Network Traffic

Directory of Open Access Journals (Sweden)

Florentin Clouet

2015-08-01

Full Text Available Providing experimenters with deep insight about the effects of their experiments is a central feature of testbeds. In this paper, we describe Kwapi, a framework designed in the context of the Grid'5000 testbed, that unifies measurements for both energy consumption and network traffic. Because all measurements are taken at the infrastructure level (using sensors in power and network equipment, using this framework has no dependencies on the experiments themselves. Initially designed for OpenStack infrastructures, the Kwapi framework allows monitoring and reporting of energy consumption of distributed platforms. In this article, we present the extension of Kwapi to network monitoring, and outline how we overcame several challenges: scaling to a testbed the size of Grid'5000 while still providing high-frequency measurements; providing long-term loss-less storage of measurements; handling operational issues when deploying such a tool on a real infrastructure.

Pinellas Plant environmental monitoring report 1986

International Nuclear Information System (INIS)

1987-04-01

The effluent and environmental monitoring programs maintained by the Pinellas Plant are designed to determine the efficiencies of treatment and control mechanisms for environmental releases; to provide measurements of discharge concentrations for comparison with applicable standards; and to assess the concentrations of these discharges in the on-site and off-site environment

Investigation of Wireless Sensor Networks for Structural Health Monitoring

Directory of Open Access Journals (Sweden)

Ping Wang

2012-01-01

Full Text Available Wireless sensor networks (WSNs are one of the most able technologies in the structural health monitoring (SHM field. Through intelligent, self-organising means, the contents of this paper will test a variety of different objects and different working principles of sensor nodes connected into a network and integrated with data processing functions. In this paper the key issues of WSN applied in SHM are discussed, including the integration of different types of sensors with different operational modalities, sampling frequencies, issues of transmission bandwidth, real-time ability, and wireless transmitter frequency. Furthermore, the topology, data fusion, integration, energy saving, and self-powering nature of different systems will be investigated. In the FP7 project “Health Monitoring of Offshore Wind Farms,” the above issues are explored.

Big Data Reduction and Optimization in Sensor Monitoring Network

Directory of Open Access Journals (Sweden)

Bin He

2014-01-01

Full Text Available Wireless sensor networks (WSNs are increasingly being utilized to monitor the structural health of the underground subway tunnels, showing many promising advantages over traditional monitoring schemes. Meanwhile, with the increase of the network size, the system is incapable of dealing with big data to ensure efficient data communication, transmission, and storage. Being considered as a feasible solution to these issues, data compression can reduce the volume of data travelling between sensor nodes. In this paper, an optimization algorithm based on the spatial and temporal data compression is proposed to cope with these issues appearing in WSNs in the underground tunnel environment. The spatial and temporal correlation functions are introduced for the data compression and data recovery. It is verified that the proposed algorithm is applicable to WSNs in the underground tunnel.

Air pollution monitoring in Amman, Jordan

International Nuclear Information System (INIS)

Al-Hasaan, A.A.; Dann, T.F.; Brunet, P.F.

1992-01-01

In 1985, a collaborative research program was established between the Royal Scientific Society of Jordan and Environment Canada, Pollution Measurement Division, Ottawa, Canada, with the objective of developing an air pollution monitoring network for Amman and preparing recommendations for national air quality standards and national emission standards for Jordan. Four monitoring sites were established in residential and commercial areas of Amman. Carbon monoxide, nitrogen dioxide, sulphur dioxide and total suspended particle matter (TSP) were measured at the Downtown station. At the other sites only TSP was measured. A short-term monitoring program carried out with a mobile monitoring unit showed relatively low levels of sulfur dioxide, carbon monoxide and nitrogen dioxide at the RSS, Naser and Marka sites as compared to the Downtown site. Continuous analyzers purchased from Environment SA, France, were used to measure sulfur dioxide, carbon monoxide and nitrogen dioxide; Sierra-Anderson high volume samplers equipped with glass fiber filters were used to collect total suspended particulates samples. Gaseous pollutants were continuously measured at the Downtown site and TSP samplers were operated on a three day schedule at all sites. Sampling began in July 1986 and continues to the present

Wireless Infrastructure M2M Network For Distributed Power Grid Monitoring.

Science.gov (United States)

Gharavi, Hamid; Hu, Bin

2017-01-01

With the massive integration of distributed renewable energy sources (RESs) into the power system, the demand for timely and reliable network quality monitoring, control, and fault analysis is rapidly growing. Following the successful deployment of Phasor Measurement Units (PMUs) in transmission systems for power monitoring, a new opportunity to utilize PMU measurement data for power quality assessment in distribution grid systems is emerging. The main problem however, is that a distribution grid system does not normally have the support of an infrastructure network. Therefore, the main objective in this paper is to develop a Machine-to-Machine (M2M) communication network that can support wide ranging sensory data, including high rate synchrophasor data for real-time communication. In particular, we evaluate the suitability of the emerging IEEE 802.11ah standard by exploiting its important features, such as classifying the power grid sensory data into different categories according to their traffic characteristics. For performance evaluation we use our hardware in the loop grid communication network testbed to access the performance of the network.

Locations of Sampling Stations for Water Quality Monitoring in Water Distribution Networks.

Science.gov (United States)

Rathi, Shweta; Gupta, Rajesh

2014-04-01

Water quality is required to be monitored in the water distribution networks (WDNs) at salient locations to assure the safe quality of water supplied to the consumers. Such monitoring stations (MSs) provide warning against any accidental contaminations. Various objectives like demand coverage, time for detection, volume of water contaminated before detection, extent of contamination, expected population affected prior to detection, detection likelihood and others, have been independently or jointly considered in determining optimal number and location of MSs in WDNs. "Demand coverage" defined as the percentage of network demand monitored by a particular monitoring station is a simple measure to locate MSs. Several methods based on formulation of coverage matrix using pre-specified coverage criteria and optimization have been suggested. Coverage criteria is defined as some minimum percentage of total flow received at the monitoring stations that passed through any upstream node included then as covered node of the monitoring station. Number of monitoring stations increases with the increase in the value of coverage criteria. Thus, the design of monitoring station becomes subjective. A simple methodology is proposed herein which priority wise iteratively selects MSs to achieve targeted demand coverage. The proposed methodology provided the same number and location of MSs for illustrative network as an optimization method did. Further, the proposed method is simple and avoids subjectivity that could arise from the consideration of coverage criteria. The application of methodology is also shown on a WDN of Dharampeth zone (Nagpur city WDN in Maharashtra, India) having 285 nodes and 367 pipes.

Earthquake Monitoring: SeisComp3 at the Swiss National Seismic Network

Science.gov (United States)

Clinton, J. F.; Diehl, T.; Cauzzi, C.; Kaestli, P.

2011-12-01

The Swiss Seismological Service (SED) has an ongoing responsibility to improve the seismicity monitoring capability for Switzerland. This is a crucial issue for a country with low background seismicity but where a large M6+ earthquake is expected in the next decades. With over 30 stations with spacing of ~25km, the SED operates one of the densest broadband networks in the world, which is complimented by ~ 50 realtime strong motion stations. The strong motion network is expected to grow with an additional ~80 stations over the next few years. Furthermore, the backbone of the network is complemented by broadband data from surrounding countries and temporary sub-networks for local monitoring of microseismicity (e.g. at geothermal sites). The variety of seismic monitoring responsibilities as well as the anticipated densifications of our network demands highly flexible processing software. We are transitioning all software to the SeisComP3 (SC3) framework. SC3 is a fully featured automated real-time earthquake monitoring software developed by GeoForschungZentrum Potsdam in collaboration with commercial partner, gempa GmbH. It is in its core open source, and becoming a community standard software for earthquake detection and waveform processing for regional and global networks across the globe. SC3 was originally developed for regional and global rapid monitoring of potentially tsunamagenic earthquakes. In order to fulfill the requirements of a local network recording moderate seismicity, SED has tuned configurations and added several modules. In this contribution, we present our SC3 implementation strategy, focusing on the detection and identification of seismicity on different scales. We operate several parallel processing "pipelines" to detect and locate local, regional and global seismicity. Additional pipelines with lower detection thresholds can be defined to monitor seismicity within dense subnets of the network. To be consistent with existing processing

Proceedings of the 1981 linear accelerator conference

International Nuclear Information System (INIS)

Jameson, R.A.; Taylor, L.S.

1982-02-01

The 1981 Linear Accelerator Conference was held at Bishop's Lodge, Santa Fe, New Mexico, October 19-23, 1981. This publication contains the texts of the invited and contributed papers. Abstracts of individual items from the conference were prepared separately for the data base

The seismic monitoring network of Mt. Vesuvius

Directory of Open Access Journals (Sweden)

Massimo Orazi

2013-11-01

Full Text Available Mt. Vesuvius (southern Italy is one of the most hazardous volcanoes in the world. Its activity is currently characterized by moderate seismicity, with hypocenters located beneath the crater zone with depth rarely exceeding 5 km and magnitudes generally less than 3. The current configuration of the seismic monitoring network of Mt. Vesuvius consists of 18 seismic stations and 7 infrasound microphones. During the period 2006-2010 a seismic array with 48 channels was also operative. The station distribution provides appropriate coverage of the area around the volcanic edifice. The current development of the network and its geometry, under conditions of low seismic noise, allows locating seismic events with M<1. Remote instruments continuously transmit data to the main acquisition center in Naples. Data transmission is realized using different technological solutions based on UHF, Wi-Fi radio links, and TCP/IP client-server applications. Data are collected in the monitoring center of the Osservatorio Vesuviano (Italian National Institute of Geophysics and Volcanology, Naples section, which is equipped with systems for displaying and analyzing signals, using both real-time automatic and manual procedures. 24-hour surveillance allows to immediately communicate any significant anomaly to the Civil Protection authorities.

Optimizing Seismic Monitoring Networks for EGS and Conventional Geothermal Projects

Science.gov (United States)

Kraft, Toni; Herrmann, Marcus; Bethmann, Falko; Stefan, Wiemer

2013-04-01

In the past several years, geological energy technologies receive growing attention and have been initiated in or close to urban areas. Some of these technologies involve injecting fluids into the subsurface (e.g., oil and gas development, waste disposal, and geothermal energy development) and have been found or suspected to cause small to moderate sized earthquakes. These earthquakes, which may have gone unnoticed in the past when they occurred in remote sparsely populated areas, are now posing a considerable risk for the public acceptance of these technologies in urban areas. The permanent termination of the EGS project in Basel, Switzerland after a number of induced ML~3 (minor) earthquakes in 2006 is one prominent example. It is therefore essential for the future development and success of these geological energy technologies to develop strategies for managing induced seismicity and keeping the size of induced earthquakes at a level that is acceptable to all stakeholders. Most guidelines and recommendations on induced seismicity published since the 1970ies conclude that an indispensable component of such a strategy is the establishment of seismic monitoring in an early stage of a project. This is because an appropriate seismic monitoring is the only way to detect and locate induced microearthquakes with sufficient certainty to develop an understanding of the seismic and geomechanical response of the reservoir to the geotechnical operation. In addition, seismic monitoring lays the foundation for the establishment of advanced traffic light systems and is therefore an important confidence building measure towards the local population and authorities. We have developed an optimization algorithm for seismic monitoring networks in urban areas that allows to design and evaluate seismic network geometries for arbitrary geotechnical operation layouts. The algorithm is based on the D-optimal experimental design that aims to minimize the error ellipsoid of the linearized

An integrated environment monitoring system for underground coal mines--Wireless Sensor Network subsystem with multi-parameter monitoring.

Science.gov (United States)

Zhang, Yu; Yang, Wei; Han, Dongsheng; Kim, Young-Il

2014-07-21

Environment monitoring is important for the safety of underground coal mine production, and it is also an important application of Wireless Sensor Networks (WSNs). We put forward an integrated environment monitoring system for underground coal mine, which uses the existing Cable Monitoring System (CMS) as the main body and the WSN with multi-parameter monitoring as the supplementary technique. As CMS techniques are mature, this paper mainly focuses on the WSN and the interconnection between the WSN and the CMS. In order to implement the WSN for underground coal mines, two work modes are designed: periodic inspection and interrupt service; the relevant supporting technologies, such as routing mechanism, collision avoidance, data aggregation, interconnection with the CMS, etc., are proposed and analyzed. As WSN nodes are limited in energy supply, calculation and processing power, an integrated network management scheme is designed in four aspects, i.e., topology management, location management, energy management and fault management. Experiments were carried out both in a laboratory and in a real underground coal mine. The test results indicate that the proposed integrated environment monitoring system for underground coal mines is feasible and all designs performed well as expected.

An Integrated Environment Monitoring System for Underground Coal Mines—Wireless Sensor Network Subsystem with Multi-Parameter Monitoring

Science.gov (United States)

Zhang, Yu; Yang, Wei; Han, Dongsheng; Kim, Young-Il

2014-01-01

Environment monitoring is important for the safety of underground coal mine production, and it is also an important application of Wireless Sensor Networks (WSNs). We put forward an integrated environment monitoring system for underground coal mine, which uses the existing Cable Monitoring System (CMS) as the main body and the WSN with multi-parameter monitoring as the supplementary technique. As CMS techniques are mature, this paper mainly focuses on the WSN and the interconnection between the WSN and the CMS. In order to implement the WSN for underground coal mines, two work modes are designed: periodic inspection and interrupt service; the relevant supporting technologies, such as routing mechanism, collision avoidance, data aggregation, interconnection with the CMS, etc., are proposed and analyzed. As WSN nodes are limited in energy supply, calculation and processing power, an integrated network management scheme is designed in four aspects, i.e., topology management, location management, energy management and fault management. Experiments were carried out both in a laboratory and in a real underground coal mine. The test results indicate that the proposed integrated environment monitoring system for underground coal mines is feasible and all designs performed well as expected. PMID:25051037

An Integrated Environment Monitoring System for Underground Coal Mines—Wireless Sensor Network Subsystem with Multi-Parameter Monitoring

Directory of Open Access Journals (Sweden)

Yu Zhang

2014-07-01

Full Text Available Environment monitoring is important for the safety of underground coal mine production, and it is also an important application of Wireless Sensor Networks (WSNs. We put forward an integrated environment monitoring system for underground coal mine, which uses the existing Cable Monitoring System (CMS as the main body and the WSN with multi-parameter monitoring as the supplementary technique. As CMS techniques are mature, this paper mainly focuses on the WSN and the interconnection between the WSN and the CMS. In order to implement the WSN for underground coal mines, two work modes are designed: periodic inspection and interrupt service; the relevant supporting technologies, such as routing mechanism, collision avoidance, data aggregation, interconnection with the CMS, etc., are proposed and analyzed. As WSN nodes are limited in energy supply, calculation and processing power, an integrated network management scheme is designed in four aspects, i.e., topology management, location management, energy management and fault management. Experiments were carried out both in a laboratory and in a real underground coal mine. The test results indicate that the proposed integrated environment monitoring system for underground coal mines is feasible and all designs performed well as expected.

Wireless Industrial Monitoring and Control Networks: The Journey So Far and the Road Ahead

Directory of Open Access Journals (Sweden)

Paul Havinga

2012-08-01

Full Text Available While traditional wired communication technologies have played a crucial role in industrial monitoring and control networks over the past few decades, they are increasingly proving to be inadequate to meet the highly dynamic and stringent demands of today’s industrial applications, primarily due to the very rigid nature of wired infrastructures. Wireless technology, however, through its increased pervasiveness, has the potential to revolutionize the industry, not only by mitigating the problems faced by wired solutions, but also by introducing a completely new class of applications. While present day wireless technologies made some preliminary inroads in the monitoring domain, they still have severe limitations especially when real-time, reliable distributed control operations are concerned. This article provides the reader with an overview of existing wireless technologies commonly used in the monitoring and control industry. It highlights the pros and cons of each technology and assesses the degree to which each technology is able to meet the stringent demands of industrial monitoring and control networks. Additionally, it summarizes mechanisms proposed by academia, especially serving critical applications by addressing the real-time and reliability requirements of industrial process automation. The article also describes certain key research problems from the physical layer communication for sensor networks and the wireless networking perspective that have yet to be addressed to allow the successful use of wireless technologies in industrial monitoring and control networks.

A mobile-agent-based wireless sensing network for structural monitoring applications

International Nuclear Information System (INIS)

Taylor, Stuart G; Farinholt, Kevin M; Figueiredo, Eloi; Moro, Erik A; Park, Gyuhae; Farrar, Charles R; Flynn, Eric B; Mascarenas, David L; Todd, Michael D

2009-01-01

A new wireless sensing network paradigm is presented for structural monitoring applications. In this approach, both power and data interrogation commands are conveyed via a mobile agent that is sent to sensor nodes to perform intended interrogations, which can alleviate several limitations of the traditional sensing networks. Furthermore, the mobile agent provides computational power to make near real-time assessments on the structural conditions. This paper will discuss such prototype systems, which are used to interrogate impedance-based sensors for structural health monitoring applications. Our wireless sensor node is specifically designed to accept various energy sources, including wireless energy transmission, and to be wirelessly triggered on an as-needed basis by the mobile agent or other sensor nodes. The capabilities of this proposed sensing network paradigm are demonstrated in the laboratory and the field

Monitoring Persistent Volcanic Emissions from Sulphur Springs, Saint Lucia: A Community Approach to Disaster Risk Reduction

Science.gov (United States)

Joseph, E. P.; Beckles, D. M.; Cox, L.; Jackson, V. B.; Alexander, D.

2014-12-01

Volcanic and geothermal emissions are known natural sources of volatiles to the atmosphere. Volcanogenic air pollutants known to cause the most serious impact are carbon dioxide (CO2), sulphur dioxide (SO2), hydrogen chloride (HCl) and hydrogen fluoride (HF). Some studies into the potential for volcanic emissions to produce chronic diseases in humans indicate that areas of major concern include respiratory problems, particularly silicosis (Allen et al. 2000; Baxter et al. 1999; Buist et al. 1986), psychological stress (Shore et al. 1986), and chemical impacts of gas or ash (Giammanco et al. 1998). Sulphur Springs Park in Saint Lucia has a very high recreational value with >200,000 visitors annually, while the nearby town of Soufrière has >8,400 residents. Residents and visitors have raised concerns about the volcanic emissions and its health effects. As part of the volcanic surveillance programme undertaken by the UWI, Seismic Research Centre (SRC) in Saint Lucia, a new monitoring network has been established for quantifying the ambient SO2 in air, to which staff and visitors at the volcanic park are exposed to. The implementation and continued operation of this network has involved the training of local personnel in the active field sampling and analytical techniques required for the assessment of ambient SO2 concentrations, using a low cost monitor as well as commercial passive samplers. This approach recognizes that environmental hazards are a usual part of life and productive livelihoods, and to minimize post-disaster response and recovery it is beneficial to promote preparedness and mitigation, which is best achieved at the local level with community involvement. It is also intended that the volcanic emissions monitoring network could be used as a method to establish and maintain community-based initiatives that would also be helpful when volcanic threat manifests.

Health Physics and Medical Services report for 1986

International Nuclear Information System (INIS)

Burt, A.K.; Bird, R.W.

1987-09-01

A Health Physics and Medical Services report is presented for Harwell Laboratory for 1986. Health physics aspects covered include safety policy and organisation, monitoring results for the working environment and personnel, an analysis of radiological incidents and radioactive waste disposal, and protection of the public. Other non-radiological aspects of health and safety are briefly considered. The section on Medical Services contains details of the staffing, the types of medical examinations performed, the treatments received, work on the safety of asbestos and manmade mineral fibres and training and education programmes. (UK)

Terrestrial radioactivity monitoring programme (TRAMP) report for 1986

International Nuclear Information System (INIS)

1988-01-01

The Ministry of Agriculture, Fisheries and Food (MAFF) undertakes a comprehensive independent monitoring programme for radioactivity in terrestrial foodstuffs in England and Wales, this report presents the results from the first full year of operation of this programme and complements the data published annually by the Ministry's Directorate of Fisheries Research in respect of the aquatic environment. This work is undertaken in Wales on behalf of the Secretary of State. The Terrestrial Radioactivity Monitoring Programme (TRAMP) concentrates on samples of agricultural produce (milk, crops, meat) collected from the vicinity of the major nuclear sites in England and Wales and is independent of monitoring undertaken for various purposes by site operators. (author)

[Design and application of user managing system of cardiac remote monitoring network].

Science.gov (United States)

Chen, Shouqiang; Zhang, Jianmin; Yuan, Feng; Gao, Haiqing

2007-12-01

According to inpatient records, data managing demand of cardiac remote monitoring network and computer, this software was designed with relative database ACCESS. Its interface, operational button and menu were designed in VBA language assistantly. Its design included collective design, amity, practicability and compatibility. Its function consisted of registering, inquiring, statisticing and printing, et al. It could be used to manage users effectively and could be helpful to exerting important action of cardiac remote monitoring network in preventing cardiac-vascular emergency ulteriorly.

Tailoring groundwater quality monitoring to vulnerability: a GIS procedure for network design.

Science.gov (United States)

Preziosi, E; Petrangeli, A B; Giuliano, G

2013-05-01

Monitoring networks aiming to assess the state of groundwater quality and detect or predict changes could increase in efficiency when fitted to vulnerability and pollution risk assessment. The main purpose of this paper is to describe a methodology aiming at integrating aquifers vulnerability and actual levels of groundwater pollution in the monitoring network design. In this study carried out in a pilot area in central Italy, several factors such as hydrogeological setting, groundwater vulnerability, and natural and anthropogenic contamination levels were analyzed and used in designing a network tailored to the monitoring objectives, namely, surveying the evolution of groundwater quality relating to natural conditions as well as to polluting processes active in the area. Due to the absence of an aquifer vulnerability map for the whole area, a proxi evaluation of it was performed through a geographic information system (GIS) methodology, leading to the so called "susceptibility to groundwater quality degradation". The latter was used as a basis for the network density assessment, while water points were ranked by several factors including discharge, actual contamination levels, maintenance conditions, and accessibility for periodical sampling in order to select the most appropriate to the network. Two different GIS procedures were implemented which combine vulnerability conditions and water points suitability, producing two slightly different networks of 50 monitoring points selected out of the 121 candidate wells and springs. The results are compared with a "manual" selection of the points. The applied GIS procedures resulted capable to select the requested number of water points from the initial set, evaluating the most confident ones and an appropriate density. Moreover, it is worth underlining that the second procedure (point distance analysis [PDA]) is technically faster and simpler to be performed than the first one (GRID + PDA).

SecMAS: Security Enhanced Monitoring and Analysis Systems for Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Ding Chao

2016-01-01

Full Text Available The monitoring, control, and security guarantee for the communication in the wireless sensor networks (WSNs are currently treated as three independent issues and addressed separately through specialized tools. However, most cases of WSNs applications requires the network administrator change the network configuration in a very short time to response to the change of observed phenomenon with security guarantee. To meet this requirement, we propose a security enhanced monitoring and control platform named SecMAS for WSNs, which provides the real-time visualization about network states and online reconfiguration of the network properties and behaviours in a resource-efficient way. Besides, basic cryptographic primitives and part of the anomaly detection functionalities are implemented in SecMAS to enabling the secure communication in WSNs. Furthermore, we conduct experiments to evaluate the performance of SecMAS in terms of the latency, throughput, communication overhead, and the security capacity. The experimental results demonstrate that the SecMAS system achieves stable, efficient and secure data collection with lightweight quick-response network control.

La pêcherie du lac Ihema (Rwanda : production commerciale et rentabilité socio-économique (1981-1987

Directory of Open Access Journals (Sweden)

Mughanda, M.

1991-01-01

Full Text Available Lake Ihema fishery (Rwanda. Commercial production and socio-economical profitability (1981-1987. Among the small lakes in the flooded area of the river Akagera, in eastern Rwanda, lake Ihema (area : 90 km2, mean depth : 4 m is the most important. The density of phytoplankton in the water is high but dissolved salts concentration is low. Ichtyofauna of the lake consists of 34 species which were occasionally exploited by tanzanian fishermen. That is why, since 1980, the government of Rwanda with the aid of the Belgian Cooperation Agency for Development have initiated an official fishery. Total yield, fishing effort and financial investments are analysed over a 7 years period (1981 to 1987 in order to precise the socio-economical efficiency of this cooperation project. Total fishery effort and total yield have increased regularly until 1983, reaching 186 tons with a fishing effort of 9.231 outings. Since that year, the production has stabilized at a level of 156-199 t/year with only two taxa exploited : Tilapia spp and Clarias gariepinus. The analysis of book-keeping and annual accountant balance of the Ihema fishery shows that the annual exploitation ratio fluctuates between 81 and 142, 5 % ; this indicates a difficult control of the expenditures at least during some years (1984, 1985 and 1986. The profit ratio shows a positive return (± 10 % since 1981 to 1983, then a depression during 1984 and a continual increase during the next years to become positive again in 1987. Continuous evaluations of these simple parameters allowed to take some actions in order to maintain the efficiency of the fishery. This new activity will be maintained if there is a good fish stock management and rigorous accounts.

Monitoring data related to the Chernobyl accident as measured in Israel during May-July 1986 and the assessment of the radiation doses to the population

International Nuclear Information System (INIS)

Schlesinger, T.; Biran, T.I.; Even, O.; Dukhan, R.; Shamai, Y.; Koch, J.; Tal, A.; Israeli, M.

1987-07-01

Environmental monitoring was undertaken on April 30 1986, to follow the effects of the Chernobyl accident on the quality of the environment in Israel. Measurements of air radioactive contamination were continuously taken to the end of July when air radioactive declined to values below 0.01 Bq/m 3 . Along air measurements, radioactive contamination of ground, rain and drinking water, grass, vegetation and food items such as vegetables, fruits, milk, meat etc. were taken as well. Assessment of the accumulated radiation doses due to the Chernobyl accident was conducted. The effective dose equivalent is estimated to be 46 μSv (4.6 mrem)

Levels of radioactivity in Wales from the accident at Chernobyl, USSR on 26 April 1986

International Nuclear Information System (INIS)

1986-07-01

This document contains a compilation of the results of environmental monitoring for radioactivity and radiation in Wales following the accident at Chernobyl, USSR, on 26 April 1986. The compilation has been prepared by the National Radiological Protection Board at the request of the Welsh Office and includes all information available to the NRPB up to 23 May 1986. Data are presented under the following headings: Background information, concentrations in air, water (rain, surface, tapwater, non-potable), grass, outdoor dose rates, concentrations in cows, goats and ewes' milk, concentrations in leafy vegetables and other foods. (U.K.)

Gasoline sales post minimal gain in 1986

Energy Technology Data Exchange (ETDEWEB)

1987-06-22

Despite the continuing emphasis on conservation and the growing trend to smaller sized automobiles, sales of motor gasoline across Canada posted a gain of 0.4% in 1986. Figures are included in this survey for Canadian motor gasoline sales categorized by province, type of gasoline, and months of 1985 and 1986. Sales of refiners' diesel fuel oil are also categorized by province and by months of 1985 and 1986. Motor gasoline disposition for 1983-1986 is categorized into retail pump sales, road and urban transport, agriculture, public administration, and commercial and other institutional markets. Also included are figures for refiners' propane sales for 1983-1986 by province.

Annual report 1981

International Nuclear Information System (INIS)

1982-01-01

The research activities during 1981 are described. Project were going on in the following fields: Theoretical nuclear physics; particle physics; field theory and mathematical physics; theoretical biophysics; and theory of metals. A short abstract is given for each project. (G.B.)

Model Based Optimal Sensor Network Design for Condition Monitoring in an IGCC Plant

Energy Technology Data Exchange (ETDEWEB)

Kumar, Rajeeva; Kumar, Aditya; Dai, Dan; Seenumani, Gayathri; Down, John; Lopez, Rodrigo

2012-12-31

This report summarizes the achievements and final results of this program. The objective of this program is to develop a general model-based sensor network design methodology and tools to address key issues in the design of an optimal sensor network configuration: the type, location and number of sensors used in a network, for online condition monitoring. In particular, the focus in this work is to develop software tools for optimal sensor placement (OSP) and use these tools to design optimal sensor network configuration for online condition monitoring of gasifier refractory wear and radiant syngas cooler (RSC) fouling. The methodology developed will be applicable to sensing system design for online condition monitoring for broad range of applications. The overall approach consists of (i) defining condition monitoring requirement in terms of OSP and mapping these requirements in mathematical terms for OSP algorithm, (ii) analyzing trade-off of alternate OSP algorithms, down selecting the most relevant ones and developing them for IGCC applications (iii) enhancing the gasifier and RSC models as required by OSP algorithms, (iv) applying the developed OSP algorithm to design the optimal sensor network required for the condition monitoring of an IGCC gasifier refractory and RSC fouling. Two key requirements for OSP for condition monitoring are desired precision for the monitoring variables (e.g. refractory wear) and reliability of the proposed sensor network in the presence of expected sensor failures. The OSP problem is naturally posed within a Kalman filtering approach as an integer programming problem where the key requirements of precision and reliability are imposed as constraints. The optimization is performed over the overall network cost. Based on extensive literature survey two formulations were identified as being relevant to OSP for condition monitoring; one based on LMI formulation and the other being standard INLP formulation. Various algorithms to solve

A Design of Wireless Sensor Networks for a Power Quality Monitoring System

Directory of Open Access Journals (Sweden)

Sanggil Kang

2010-11-01

Full Text Available Power grids deal with the business of generation, transmission, and distribution of electric power. Recently, interest in power quality in electrical distribution systems has increased rapidly. In Korea, the communication network to deliver voltage, current, and temperature measurements gathered from pole transformers to remote monitoring centers employs cellular mobile technology. Due to high cost of the cellular mobile technology, power quality monitoring measurements are limited and data gathering intervals are large. This causes difficulties in providing the power quality monitoring service. To alleviate the problems, in this paper we present a communication infrastructure to provide low cost, reliable data delivery. The communication infrastructure consists of wired connections between substations and monitoring centers, and wireless connections between pole transformers and substations. For the wireless connection, we employ a wireless sensor network and design its corresponding data forwarding protocol to improve the quality of data delivery. For the design, we adopt a tree-based data forwarding protocol in order to customize the distribution pattern of the power quality information. We verify the performance of the proposed data forwarding protocol quantitatively using the NS-2 network simulator.

A design of wireless sensor networks for a power quality monitoring system.

Science.gov (United States)

Lim, Yujin; Kim, Hak-Man; Kang, Sanggil

2010-01-01

Power grids deal with the business of generation, transmission, and distribution of electric power. Recently, interest in power quality in electrical distribution systems has increased rapidly. In Korea, the communication network to deliver voltage, current, and temperature measurements gathered from pole transformers to remote monitoring centers employs cellular mobile technology. Due to high cost of the cellular mobile technology, power quality monitoring measurements are limited and data gathering intervals are large. This causes difficulties in providing the power quality monitoring service. To alleviate the problems, in this paper we present a communication infrastructure to provide low cost, reliable data delivery. The communication infrastructure consists of wired connections between substations and monitoring centers, and wireless connections between pole transformers and substations. For the wireless connection, we employ a wireless sensor network and design its corresponding data forwarding protocol to improve the quality of data delivery. For the design, we adopt a tree-based data forwarding protocol in order to customize the distribution pattern of the power quality information. We verify the performance of the proposed data forwarding protocol quantitatively using the NS-2 network simulator.

Research on a Banknote Printing Wastewater Monitoring System based on Wireless Sensor Network

International Nuclear Information System (INIS)

Li, B B; Yuan, Z F

2006-01-01

In this paper, a banknote printing wastewater monitoring system based on WSN is presented in line with the system demands and actual condition of the worksite for a banknote printing factory. In Physical Layer, the network node is a nRF9e5-centric embedded instrument, which can realize the multi-function such as data collecting, status monitoring, wireless data transmission and so on. Limited by the computing capability, memory capability, communicating energy and others factors, it is impossible for the node to get every detail information of the network, so the communication protocol on WSN couldn't be very complicated. The competitive-based MACA (Multiple Access with Collision Avoidance) Protocol is introduced in MAC, which can decide the communication process and working mode of the nodes, avoid the collision of data transmission, hidden and exposed station problem of nodes. On networks layer, the routing protocol in charge of the transmitting path of the data, the networks topology structure is arranged based on address assignation. Accompanied with some redundant nodes, the network performances stabile and expandable. The wastewater monitoring system is a tentative practice of WSN theory in engineering. Now, the system has passed test and proved efficiently

Instrument surveillance and calibration verification through plant wide monitoring using autoassociative neural networks

International Nuclear Information System (INIS)

Wrest, D.J.; Hines, J.W.; Uhrig, R.E.

1996-01-01

The approach to instrument surveillance and calibration verification (ISCV) through plant wide monitoring proposed in this paper is an autoassociative neural network (AANN) which will utilize digitized data presently available in the Safety Parameter Display computer system from Florida Power Corporations Crystal River number 3 nuclear power plant. An autoassociative neural network is one in which the outputs are trained to emulate the inputs over an appropriate dynamic range. The relationships between the different variables are embedded in the weights by the training process. As a result, the output can be a correct version of an input pattern that has been distorted by noise, missing data, or non-linearities. Plant variables that have some degree of coherence with each other constitute the inputs to the network. Once the network has been trained with normal operational data it has been shown to successfully monitor the selected plant variables to detect sensor drift or failure by simply comparing the network inputs with the outputs. The AANN method of monitoring many variables not only indicates that there is a sensor failure, it clearly indicates the signal channel in which the signal error has occurred. (author). 11 refs, 8 figs, 2 tabs

Instrument surveillance and calibration verification through plant wide monitoring using autoassociative neural networks

Energy Technology Data Exchange (ETDEWEB)

Wrest, D J; Hines, J W; Uhrig, R E [Tennessee Univ., Knoxville, TN (United States). Dept. of Nuclear Engineering

1997-12-31

The approach to instrument surveillance and calibration verification (ISCV) through plant wide monitoring proposed in this paper is an autoassociative neural network (AANN) which will utilize digitized data presently available in the Safety Parameter Display computer system from Florida Power Corporations Crystal River number 3 nuclear power plant. An autoassociative neural network is one in which the outputs are trained to emulate the inputs over an appropriate dynamic range. The relationships between the different variables are embedded in the weights by the training process. As a result, the output can be a correct version of an input pattern that has been distorted by noise, missing data, or non-linearities. Plant variables that have some degree of coherence with each other constitute the inputs to the network. Once the network has been trained with normal operational data it has been shown to successfully monitor the selected plant variables to detect sensor drift or failure by simply comparing the network inputs with the outputs. The AANN method of monitoring many variables not only indicates that there is a sensor failure, it clearly indicates the signal channel in which the signal error has occurred. (author). 11 refs, 8 figs, 2 tabs.

A Survey of Wireless Sensor Network Based Air Pollution Monitoring Systems.

Science.gov (United States)

Yi, Wei Ying; Lo, Kin Ming; Mak, Terrence; Leung, Kwong Sak; Leung, Yee; Meng, Mei Ling

2015-12-12

The air quality in urban areas is a major concern in modern cities due to significant impacts of air pollution on public health, global environment, and worldwide economy. Recent studies reveal the importance of micro-level pollution information, including human personal exposure and acute exposure to air pollutants. A real-time system with high spatio-temporal resolution is essential because of the limited data availability and non-scalability of conventional air pollution monitoring systems. Currently, researchers focus on the concept of The Next Generation Air Pollution Monitoring System (TNGAPMS) and have achieved significant breakthroughs by utilizing the advance sensing technologies, MicroElectroMechanical Systems (MEMS) and Wireless Sensor Network (WSN). However, there exist potential problems of these newly proposed systems, namely the lack of 3D data acquisition ability and the flexibility of the sensor network. In this paper, we classify the existing works into three categories as Static Sensor Network (SSN), Community Sensor Network (CSN) and Vehicle Sensor Network (VSN) based on the carriers of the sensors. Comprehensive reviews and comparisons among these three types of sensor networks were also performed. Last but not least, we discuss the limitations of the existing works and conclude the objectives that we want to achieve in future systems.

Performance assessment of air quality monitoring networks using principal component analysis and cluster analysis

International Nuclear Information System (INIS)

Lu, Wei-Zhen; He, Hong-Di; Dong, Li-yun

2011-01-01

This study aims to evaluate the performance of two statistical methods, principal component analysis and cluster analysis, for the management of air quality monitoring network of Hong Kong and the reduction of associated expenses. The specific objectives include: (i) to identify city areas with similar air pollution behavior; and (ii) to locate emission sources. The statistical methods were applied to the mass concentrations of sulphur dioxide (SO 2 ), respirable suspended particulates (RSP) and nitrogen dioxide (NO 2 ), collected in monitoring network of Hong Kong from January 2001 to December 2007. The results demonstrate that, for each pollutant, the monitoring stations are grouped into different classes based on their air pollution behaviors. The monitoring stations located in nearby area are characterized by the same specific air pollution characteristics and suggested with an effective management of air quality monitoring system. The redundant equipments should be transferred to other monitoring stations for allowing further enlargement of the monitored area. Additionally, the existence of different air pollution behaviors in the monitoring network is explained by the variability of wind directions across the region. The results imply that the air quality problem in Hong Kong is not only a local problem mainly from street-level pollutions, but also a region problem from the Pearl River Delta region. (author)

Monitoring of stability of ASG-EUPOS network coordinates

Science.gov (United States)

Figurski, M.; Szafranek, K.; Wrona, M.

2009-04-01

ASG-EUPOS (Active Geodetic Network - European Position Determination System) is the national system of precise satellite positioning in Poland, which increases a density of regional and global GNSS networks and is widely used by public administration, national institutions, entrepreneurs and citizens (especially surveyors). In near future ASG-EUPOS is to take role of main national network. Control of proper activity of stations and realization of ETRS'89 is a necessity. User of the system needs to be sure that observations quality and coordinates accuracy are high enough. Coordinates of IGS (International GNSS Service) and EPN (European Permanent Network) stations are precisely determined and any changes are monitored all the time. Observations are verified before they are archived in regional and global databases. The same applies to ASG-EUPOS. This paper concerns standardization of GNSS observations from different stations (uniform adjustment), examination of solutions correctness according to IGS and EPN standards and stability of solutions and sites activity

Application of network technology to Remote Monitoring System

International Nuclear Information System (INIS)

Johnson, C.S.; Sorokowski, D.L.; Veevers, K.

1994-01-01

The Australian Safeguards Office (ASO) and the US Department of Energy (DOE) have sponsored work under a bilateral agreement to implement a Remote Monitoring System (RMS) at an Australian nuclear site operated by the Australian Nuclear Science and Technology Organization (ANSTO). The RMS, designed by Sandia National Laboratories (SNL), was installed in February 1994 at the Dry Spent Fuel Storage Facility (DSFSF) located at Lucas Heights, Australia. The RMS was designed to test a number of different concepts that would be useful for unattended remote monitoring activities. The DSFSF located in Building 27 is a very suitable test site for a RMS. The RMS uses a network of low cost nodes to collect data from a number of different sensors and security devices. Different sensors and detection devices have been installed to study how they can be used to complement each other for C/S applications. The data collected from the network will allow a comparison of how the various types of sensors perform under the same set of conditions. A video system using digital compression collects digital images and stores them on a hard drive and a digital optical disk. Data and images from the storage area are remotely monitored via telephone from Canberra, Australia and Albuquerque, NM, USA. These remote monitoring stations operated by ASO and SNL respectively, can retrieve data and images from the RMS computer at the DSFSF. The data and images are encrypted before transmission. The Remote Monitoring System field tests have been operational for six months with good test results. Sensors have performed well and the digital images have excellent resolution. The hardware and software have performed reliably without any major difficulties. This paper summarizes the highlights of the prototype system and the ongoing field tests

Radioactivity in surface and coastal waters of the British Isles, 1986

International Nuclear Information System (INIS)

Hunt, G.J.

1987-01-01

The report presents the results of the environmental monitoring programme carried out during 1986 by staff of the Directorate of Fisheries Research, Lowestoft, United Kingdom. The programme was set up to verify the satisfactory control of liquid radioactive waste discharges to the aquatic environment, and to ensure that the resulting public radiation exposure is within nationally-accepted limits. The environmental programme includes monitoring the environmental consequences of discharges of liquid radioactive wastes from four British Nuclear Fuels plc sites - at Sellafield, Springfield, Capenhurst and Chapelcross, and monitoring the environment impact of liquid radioactive discharges from Winfrith and Dounraey. Monitoring is also carried out near nuclear power stations operated by the electricity boards, near Naval establishments, near Amersham International plc, and the marine environment of the Channel Islands States. Results are also presented on the monitoring of the freshwater environment for radioactivity from the Chernobyl reactor accident. (U.K.)

Monitoring individual traffic flows within the ATLAS TDAQ network

International Nuclear Information System (INIS)

Sjoen, R; Batraneanu, S M; Leahu, L; Martin, B; Al-Shabibi, A; Stancu, S; Ciobotaru, M

2010-01-01

The ATLAS data acquisition system consists of four different networks interconnecting up to 2000 processors using up to 200 edge switches and five multi-blade chassis devices. The architecture of the system has been described in [1] and its operational model in [2]. Classical, SNMP-based, network monitoring provides statistics on aggregate traffic, but for performance monitoring and troubleshooting purposes there was an imperative need to identify and quantify single traffic flows. sFlow [3] is an industry standard based on statistical sampling which attempts to provide a solution to this. Due to the size of the ATLAS network, the collection and analysis of the sFlow data from all devices generates a data handling problem of its own. This paper describes how this problem is addressed by making it possible to collect and store data either centrally or distributed according to need. The methods used to present the results in a relevant fashion for system analysts are discussed and we explore the possibilities and limitations of this diagnostic tool, giving an example of its use in solving system problems that arise during the ATLAS data taking.

Atmospheric sciences division. Annual report, fiscal year 1981

International Nuclear Information System (INIS)

Raynor, G.S.

1981-12-01

The research activities of the Atmospheric Sciences Division of the Department of Energy and Environment for FY 1981 are presented. Facilities and major items of equipment are described. Research programs are summarized in three categories, modeling, field and laboratory experiments and data management and analysis. Each program is also described individually with title, principal investigator, sponsor and funding levels for FY 1981 and FY 1982. Future plans are summarized. Publications for FY 1981 are listed with abstracts. A list of personnel is included

Application of SNODAS and hydrologic models to enhance entropy-based snow monitoring network design

Science.gov (United States)

Keum, Jongho; Coulibaly, Paulin; Razavi, Tara; Tapsoba, Dominique; Gobena, Adam; Weber, Frank; Pietroniro, Alain

2018-06-01

Snow has a unique characteristic in the water cycle, that is, snow falls during the entire winter season, but the discharge from snowmelt is typically delayed until the melting period and occurs in a relatively short period. Therefore, reliable observations from an optimal snow monitoring network are necessary for an efficient management of snowmelt water for flood prevention and hydropower generation. The Dual Entropy and Multiobjective Optimization is applied to design snow monitoring networks in La Grande River Basin in Québec and Columbia River Basin in British Columbia. While the networks are optimized to have the maximum amount of information with minimum redundancy based on entropy concepts, this study extends the traditional entropy applications to the hydrometric network design by introducing several improvements. First, several data quantization cases and their effects on the snow network design problems were explored. Second, the applicability the Snow Data Assimilation System (SNODAS) products as synthetic datasets of potential stations was demonstrated in the design of the snow monitoring network of the Columbia River Basin. Third, beyond finding the Pareto-optimal networks from the entropy with multi-objective optimization, the networks obtained for La Grande River Basin were further evaluated by applying three hydrologic models. The calibrated hydrologic models simulated discharges using the updated snow water equivalent data from the Pareto-optimal networks. Then, the model performances for high flows were compared to determine the best optimal network for enhanced spring runoff forecasting.

Verification of WIMSD-5A code on light water reactor benchmarks

International Nuclear Information System (INIS)

Ravnik, M.; Trkov, A.; Zefran, B.; Persic, A.

1996-01-01

Testing of a newly released version of WIMS code, WIMSD-5A, is presented. It is compared to the previous version, WIMS-D/4. The cross-section libraries of WIMSD-5A, denoted '1986', and of WIMS-D/4, denoted '1981', are compared as well. No significant differences in performance between WIMS-D/4 and WIMSD-5A are observed, provided the same data library is used. Significant differences in results are observed if '1981' and '1986' libraries are used with the same version of the code, WIMSD-5A. It is not clearly evident that the new library '1986' is any better than the old '1981' library. Additional tests and more detailed analysis is required. (author)

HTTR operation monitoring with neural network in 30 days operation at 850degC

International Nuclear Information System (INIS)

Shimizu, Atsushi; Nabeshima, Kunihiko; Nakagawa, Shigeaki

2009-01-01

The High temperature engineering test reactor (HTTR) executed the rated power operation for 30days of the first time (850degC in temperature of the nuclear reactor outlet coolant) until March, 27th through April, 26th, 2007. In this operation, HTTR was observed according to the operation monitoring model with the neural network, and the detection performance of neural network was verified during slight changes of reactor state at rated power. The neural network used for the operation monitoring was an auto-associative network, where 31 input 31 outputs and the hidden layers were connected with 20 units by the hierarchy of three layer structure. Back-propagation algorithm was used for study rule. The operation monitoring model in initial study was constructed by using the power up data between 30% and rated power, which were randomly studied. The adjustment study during the operation monitoring changes the internal structure of the initial study model to follow the changes of reactor status, such as the burn-up of the nuclear fuel for the rated power operation. As a monitoring result, slight changes of reactor state by the control system operation were correctly detected, and the on-line application to an early anomaly diagnosis for HTTR facilities will be expected. (author)

A Wearable Wireless Sensor Network for Indoor Smart Environment Monitoring in Safety Applications.

Science.gov (United States)

Antolín, Diego; Medrano, Nicolás; Calvo, Belén; Pérez, Francisco

2017-02-14

This paper presents the implementation of a wearable wireless sensor network aimed at monitoring harmful gases in industrial environments. The proposed solution is based on a customized wearable sensor node using a low-power low-rate wireless personal area network (LR-WPAN) communications protocol, which as a first approach measures CO₂ concentration, and employs different low power strategies for appropriate energy handling which is essential to achieving long battery life. These wearables nodes are connected to a deployed static network and a web-based application allows data storage, remote control and monitoring of the complete network. Therefore, a complete and versatile remote web application with a locally implemented decision-making system is accomplished, which allows early detection of hazardous situations for exposed workers.

A Wearable Wireless Sensor Network for Indoor Smart Environment Monitoring in Safety Applications

Directory of Open Access Journals (Sweden)

Diego Antolín

2017-02-01

Full Text Available This paper presents the implementation of a wearable wireless sensor network aimed at monitoring harmful gases in industrial environments. The proposed solution is based on a customized wearable sensor node using a low-power low-rate wireless personal area network (LR-WPAN communications protocol, which as a first approach measures CO2 concentration, and employs different low power strategies for appropriate energy handling which is essential to achieving long battery life. These wearables nodes are connected to a deployed static network and a web-based application allows data storage, remote control and monitoring of the complete network. Therefore, a complete and versatile remote web application with a locally implemented decision-making system is accomplished, which allows early detection of hazardous situations for exposed workers.

Building Capacity for Earthquake Monitoring: Linking Regional Networks with the Global Community

Science.gov (United States)

Willemann, R. J.; Lerner-Lam, A.

2006-12-01

Installing or upgrading a seismic monitoring network is often among the mitigation efforts after earthquake disasters, and this is happening in response to the events both in Sumatra during December 2004 and in Pakistan during October 2005. These networks can yield improved hazard assessment, more resilient buildings where they are most needed, and emergency relief directed more quickly to the worst hit areas after the next large earthquake. Several commercial organizations are well prepared for the fleeting opportunity to provide the instruments that comprise a seismic network, including sensors, data loggers, telemetry stations, and the computers and software required for the network center. But seismic monitoring requires more than hardware and software, no matter how advanced. A well-trained staff is required to select appropriate and mutually compatible components, install and maintain telemetered stations, manage and archive data, and perform the analyses that actually yield the intended benefits. Monitoring is more effective when network operators cooperate with a larger community through free and open exchange of data, sharing information about working practices, and international collaboration in research. As an academic consortium, a facility operator and a founding member of the International Federation of Digital Seismographic Networks, IRIS has access to a broad range of expertise with the skills that are required to help design, install, and operate a seismic network and earthquake analysis center, and stimulate the core training for the professional teams required to establish and maintain these facilities. But delivering expertise quickly when and where it is unexpectedly in demand requires advance planning and coordination in order to respond to the needs of organizations that are building a seismic network, either with tight time constraints imposed by the budget cycles of aid agencies following a disastrous earthquake, or as part of more informed

Neural networks for the monitoring of rotating machinery

International Nuclear Information System (INIS)

Alguindigue, I.E.; Loskiewicz-Buczak

1991-01-01

Vibration monitoring of components in engineering systems and plants involves the collection of vibration data and detailed analysis to detect features which reflect the operational state of the machinery. The analysis leads to the identification of potential failures and their causes, and makes it possible to perform efficient preventive maintenance. This paper describes a methodology for the automation of some of the activities related to motion and vibration monitoring in these systems. The technique involves training a neural network to model the inter- relationship between signals from two related sensors mounted on an engineering system or component at a time when it is known to be operating properly. Then one signal (or its characteristics) is put into the neural network model to predict the second signal (or its characteristics). This predicted signal is continuously compared with the actual signal A deviation between the predicted and actual signal indicates a changing relationship, usually failure of the component or system. This deviation may be quantified and provides meaningful information about the degree of degradation and deterioration of the component

Using LSTM recurrent neural networks for monitoring the LHC superconducting magnets

Science.gov (United States)

Wielgosz, Maciej; Skoczeń, Andrzej; Mertik, Matej

2017-09-01

The superconducting LHC magnets are coupled with an electronic monitoring system which records and analyzes voltage time series reflecting their performance. A currently used system is based on a range of preprogrammed triggers which launches protection procedures when a misbehavior of the magnets is detected. All the procedures used in the protection equipment were designed and implemented according to known working scenarios of the system and are updated and monitored by human operators. This paper proposes a novel approach to monitoring and fault protection of the Large Hadron Collider (LHC) superconducting magnets which employs state-of-the-art Deep Learning algorithms. Consequently, the authors of the paper decided to examine the performance of LSTM recurrent neural networks for modeling of voltage time series of the magnets. In order to address this challenging task different network architectures and hyper-parameters were used to achieve the best possible performance of the solution. The regression results were measured in terms of RMSE for different number of future steps and history length taken into account for the prediction. The best result of RMSE = 0 . 00104 was obtained for a network of 128 LSTM cells within the internal layer and 16 steps history buffer.

Materials of scientific symposium Chernobyl 1986-1996

International Nuclear Information System (INIS)

1996-01-01

The scientific symposium 'Chernobyl 1986-1996' has been devoted to assessment of consequences for environment and human population of Chernobylsk-4 Nuclear Reactor accident. The environment contamination in Poland has been performed on the base of monitoring results carried out during the decade after the event. The influence of environment and food contamination for human health has been assessed in detail. The organization of medical preventive action, especially in children population in Poland has been positively assessed as well as cooperation of governmental and territorial authorities immediately after the accident. The long-lasting consequences of environment contamination and radionuclide migration to crops and food products have been also discussed

SeaDataNet network services monitoring: Definition and Implementation of Service availability index

Science.gov (United States)

Lykiardopoulos, Angelos; Mpalopoulou, Stavroula; Vavilis, Panagiotis; Pantazi, Maria; Iona, Sissy

2014-05-01

SeaDataNet (SDN) is a standardized system for managing large and diverse data sets collected by the oceanographic fleets and the automatic observation systems. The SeaDataNet network is constituted of national oceanographic data centres of 35 countries, active in data collection. SeaDataNetII project's objective is to upgrade the present SeaDataNet infrastructure into an operationally robust and state-of-the-art infrastructure; therefore Network Monitoring is a step to this direction. The term Network Monitoring describes the use of system that constantly monitors a computer network for slow or failing components and that notifies the network administrator in case of outages. Network monitoring is crucial when implementing widely distributed systems over the Internet and in real-time systems as it detects malfunctions that may occur and notifies the system administrator who can immediately respond and correct the problem. In the framework of SeaDataNet II project a monitoring system was developed in order to monitor the SeaDataNet components. The core system is based on Nagios software. Some plug-ins were developed to support SeaDataNet modules. On the top of Nagios Engine a web portal was developed in order to give access to local administrators of SeaDataNet components, to view detailed logs of their own service(s). Currently the system monitors 35 SeaDataNet Download Managers, 9 SeaDataNet Services, 25 GeoSeas Download Managers and 23 UBSS Download Managers . Taking advantage of the continuous monitoring of SeaDataNet system components a total availability index will be implemented. The term availability can be defined as the ability of a functional unit to be in a state to perform a required function under given conditions at a given instant of time or over a given time interval, assuming that the required external resources are provided. Availability measures can be considered as a are very important benefit becauseT - The availability trends that can be

On the Relevance of Using OpenWireless Sensor Networks in Environment Monitoring

Directory of Open Access Journals (Sweden)

Antoine B. Bagula

2009-06-01

Full Text Available This paper revisits the problem of the readiness for field deployments of wireless- sensor networks by assessing the relevance of using Open Hardware and Software motes for environment monitoring. We propose a new prototype wireless sensor network that finetunes SquidBee motes to improve the life-time and sensing performance of an environment monitoring system that measures temperature, humidity and luminosity. Building upon two outdoor sensing scenarios, we evaluate the performance of the newly proposed energy-aware prototype solution in terms of link quality when expressed by the Received Signal Strength, Packet Loss and the battery lifetime. The experimental results reveal the relevance of using the Open Hardware and Software motes when setting up outdoor wireless sensor networks.

Ontario Hydro annual report 1986

International Nuclear Information System (INIS)

1987-04-01

Ontario Hydro's annual report of the financial position and activities for the year 1986 consists of their financial highlights; corporate profile; customer service and satisfaction; message from Chairman; message from President; 1986 in review; financial section; management report; five-year summary of financial statistics; and comparative statistics

Monitoring the US ATLAS Network Infrastructure with perfSONAR-PS

International Nuclear Information System (INIS)

McKee, Shawn; Lake, Andrew; Laurens, Philippe; Severini, Horst; Wlodek, Tomasz; Wolff, Stephen; Zurawski, Jason

2012-01-01

Global scientific collaborations, such as ATLAS, continue to push the network requirements envelope. Data movement in this collaboration is routinely including the regular exchange of petabytes of datasets between the collection and analysis facilities in the coming years. These requirements place a high emphasis on networks functioning at peak efficiency and availability; the lack thereof could mean critical delays in the overall scientific progress of distributed data-intensive experiments like ATLAS. Network operations staff routinely must deal with problems deep in the infrastructure; this may be as benign as replacing a failing piece of equipment, or as complex as dealing with a multi-domain path that is experiencing data loss. In either case, it is crucial that effective monitoring and performance analysis tools are available to ease the burden of management. We will report on our experiences deploying and using the perfSONAR-PS Performance Toolkit at ATLAS sites in the United States. This software creates a dedicated monitoring server, capable of collecting and performing a wide range of passive and active network measurements. Each independent instance is managed locally, but able to federate on a global scale; enabling a full view of the network infrastructure that spans domain boundaries. This information, available through web service interfaces, can easily be retrieved to create customized applications. The US ATLAS collaboration has developed a centralized “dashboard” offering network administrators, users, and decision makers the ability to see the performance of the network at a glance. The dashboard framework includes the ability to notify users (alarm) when problems are found, thus allowing rapid response to potential problems and making perfSONAR-PS crucial to the operation of our distributed computing infrastructure.

An Overview of Sensor networks for Environmental Noise Monitoring

NARCIS (Netherlands)

Basten, T.G.H.; Wessels, P.W.

2014-01-01

The last decade has shown a growing number and wide variety of systems for monitoring environmental noise. This ongoing development is made possible by the availability of cheaper and smaller hardware and innovations in communication networks. The developments are fed by a growing interest in

The Relationship Between Attachment Styles, Self-Monitoring and Cybercrime in Social Network Users.

Science.gov (United States)

Yaghoobi, Abolghasem; Mohammadzade, Serwa; Chegini, Ali Asghar; Yarmohammadi Vasel, Mosaeib; Zoghi Paidar, Mohammad Reza

2016-09-01

The anonymity in the cyberspace environment, as well as the rapid advent of and improvements to online activities has increased cybercrime. The aim of this paper was to survey the relationship between attachment styles, self-monitoring and cybercrime in social network users. The Collins and Read Adult Attachment Scale, and the Snyder self-monitoring and cybercrime scales were sent to 500 social network users. Of these, 203 users (103 men and 100 women) filled out the questionnaires. The results showed that women achieved higher scores in self-monitoring and the anxious attachment style, and men achieved higher scores in cybercrime and the anxious attachment style. There was a negative correlation between self-monitoring and cybercrime, and the anxious attachment style had a positive correlation with cybercrime and a negative correlation with self-monitoring. The secure attachment style had a positive correlation with self-monitoring and a negative correlation with cybercrime. The dependent attachment style had a positive correlation with self-monitoring and a negative correlation with cybercrime. All correlations were significant. Attachment styles have significant relationships with both self-monitoring and cybercrime. Self-monitoring and attachment styles are significant predictors of cybercrimes.

Hogthrob: Towards a Sensor Network Infrastructure for Sow Monitoring (wireless sensor network special day)

DEFF Research Database (Denmark)

Bonnet, Philippe; Leopold, Martin; Madsen, K

2006-01-01

We aim at developing a next-generation system for sow monitoring. Today, farmers use RFID based solutions with an ear tag on the sows and a reader located inside the feeding station. This does not allow the farmers to locate a sow in a large pen, or to monitor the life cycle of the sow (detect he...... period, detect injury...). Our goal is to explore the design of a sensor network that supports such functionalities and meets the constraints of this industry in terms of price, energy consumption and availability....

Final report on the Risoe monitoring programme after the Chernobyl accident for the period Oct 1, 1986 - Sept 30, 1987

International Nuclear Information System (INIS)

Aarkrog, A.; Nielsen, S.P.; Dahlgaard, H.; Lauridsen, B.; Soegaard-Hansen, J.

1988-01-01

In cooperation with the National Agency of Environmental Protection in Denmark, Risoe National Laboratory has examined the radioactive contamination from the Chernobyl accident. The programme for these investigations was an expansion of the countrywide monitoring programme operated since 1962 by Risoe National Laboratory. The present report cover the period Oct 1, 1986 to Sept. 30, 1987. All types of environmental samples relevant for radioactive contamination has been analysed. Most samples were collected countrywide and all samples were analysed for radiocaesium ( 134 Cs and 137 Cs). Many samples were furthermore anlaysed for 90 Sr and in a few samples transuranic elements ( 29,240 Pu, 241 Am and 242 Cm) were determined. On the basis of the diet and wholebody measurements of radiocaesium the individual mean dose equivalent commitment from Danish diet consumed in the first two years after the Chernobyl accident was calculated to 27 μ Sv. (author)

Measurement of anthropogenic radionuclides in the atmosphere with a radionuclide monitoring network for nuclear tests

International Nuclear Information System (INIS)

Yonezawa, Chushiro; Yamamoto, Yoichi

2011-01-01

A worldwide radionuclide monitoring network for nuclear tests has detected the anthropogenic radioactive materials released in the atmosphere due to the accident of the Fukushima Daiichi Nuclear Power Plant impacted by the Great East Japan Earthquake on March 11, 2011. After four months have passed since the accident occurred, most overseas stations do not detect the radionuclides of Fukushima origin any more. The Takasaki station in Japan, however, is still detecting them every day. This paper describes radionuclide monitoring stations and the network of them as part of the International Monitoring System (IMS) in the Comprehensive Nuclear Test Ban Treaty (CTBT), as well as the measurement results of radionuclide particulates and radioactive isotopes of xenon released from the Fukushima Daiichi Nuclear Power Plant with the monitoring network. (J.P.N.)

Role of monitoring network in the control management of air quality. An industrial case history

Energy Technology Data Exchange (ETDEWEB)

Zerbo, G. [Catania Univ. (Italy). Inst. of Merceology; Fabiano, B.; Ferraiolo, A.; Solisio, C.; Ruaro, R.

1995-12-31

Air quality control by a system of monitoring station is indispensable for the environmental protection. Moreover, a monitoring network have not to be only a mere data collection a good air quality control is possible only if the network management allows to prevent unacceptable pollutants level. In other terms, elaboration and interpretation data are fundamental in order to make monitoring system really able for regulations of corrective measures as, for example, the reduction of local emissions. The case of monitoring network run from the Industrial Society CIPA of Siracusa (Italy) is discussed. The management of the data obtained from a continuous survey allows to keep pollutants level below the current limits set down by the Italian law. Furthermore, elaboration of the data allows useful evaluations about atmospheric dispersion phenomena. (author)

Role of monitoring network in the control management of air quality. An industrial case history

Energy Technology Data Exchange (ETDEWEB)

Zerbo, G [Catania Univ. (Italy). Inst. of Merceology; Fabiano, B; Ferraiolo, A; Solisio, C; Ruaro, R

1996-12-31

Air quality control by a system of monitoring station is indispensable for the environmental protection. Moreover, a monitoring network have not to be only a mere data collection a good air quality control is possible only if the network management allows to prevent unacceptable pollutants level. In other terms, elaboration and interpretation data are fundamental in order to make monitoring system really able for regulations of corrective measures as, for example, the reduction of local emissions. The case of monitoring network run from the Industrial Society CIPA of Siracusa (Italy) is discussed. The management of the data obtained from a continuous survey allows to keep pollutants level below the current limits set down by the Italian law. Furthermore, elaboration of the data allows useful evaluations about atmospheric dispersion phenomena. (author)

Ontario Hydro annual report 1986

Energy Technology Data Exchange (ETDEWEB)

1987-04-01

Ontario Hydro`s annual report of the financial position and activities for the year 1986 consists of their financial highlights; corporate profile; customer service and satisfaction; message from Chairman; message from President; 1986 in review; financial section; management report; five-year summary of financial statistics; and comparative statistics.

Environmental radioactivity in Denmark in 1986

International Nuclear Information System (INIS)

Aarkrog, A.; Boetter-Jensen, L.; Chen Qing Jiang; Dahlgaard, H.; Hansen, H.; Holm, E.; Lauridsen, B.; Nielsen, S.P.; Soegaard-Hansen, J.

1988-11-01

Strontium-90, radiocesium and other radionuclides were determined in samples from all over the country of air, precipitation, stream water, lake water, ground water, drinking water, sea water, soil, sediments, dried milk, fresh milk, meat, fish, chese, eggs, grain, bread, potatoes, vegetables, fruit, grass, moss, lichen, sea plants, total diet, and humans. Estimates of the mean contents of radiostrontium and radiocesium in the human diet in Denmark during 1986 are given. Tritium was determined in precipitation, ground water, other fresh waters and sea water. The gamma-background was measured regularly by TLD, ionization chamber and on site gamma-spectroscopy at locations around Risoe, at ten of the State experimental farms, along the coasts of the Great Belt and around Gylling Naes. The marine environments at Barsebaeck and Ringhals were monitored for 137Cs and corrosion products (58Co, 60Co, 65Zn, 54Mn). The Chernobyl accident caused a substantial expansion of the environmental monitoring activities in Denmark. The programme was expanded to an extent similar to that in the sixties. (author) 178 tabs., 70 ills., 34 refs

KWO annual report 1986

International Nuclear Information System (INIS)

Koerner, C.

1987-01-01

The Obrigheim nuclear power station was operated at full load during the year 1986; 7869 operating hours procuded electrical energy of 2795 GWh. This is the best annual result during Obrigheim's operating period. Since commissioning in October 1968, 131595 hours of operation have generated 44074 GWh (gross) and from test operation in March 1969 until the end of 1986, 131179 hours of operation have generated 43,962 GWh. This is an availability of power of 81.5% in this period and a time availability of 83.9%. In 1986, the plant was shut down for 807 hours for the 17th refueling including refurbishing, inspection and repair work. Apart from refueling, the plant had a good time availability and therefore contributed 5% to the safe, economical and environmentally acceptable electricity supply of the Land Baden-Wuerttemberg. (orig./HP) [de

A Compression Algorithm in Wireless Sensor Networks of Bearing Monitoring

International Nuclear Information System (INIS)

Zheng Bin; Meng Qingfeng; Wang Nan; Li Zhi

2011-01-01

The energy consumption of wireless sensor networks (WSNs) is always an important problem in the application of wireless sensor networks. This paper proposes a data compression algorithm to reduce amount of data and energy consumption during the data transmission process in the on-line WSNs-based bearing monitoring system. The proposed compression algorithm is based on lifting wavelets, Zerotree coding and Hoffman coding. Among of that, 5/3 lifting wavelets is used for dividing data into different frequency bands to extract signal characteristics. Zerotree coding is applied to calculate the dynamic thresholds to retain the attribute data. The attribute data are then encoded by Hoffman coding to further enhance the compression ratio. In order to validate the algorithm, simulation is carried out by using Matlab. The result of simulation shows that the proposed algorithm is very suitable for the compression of bearing monitoring data. The algorithm has been successfully used in online WSNs-based bearing monitoring system, in which TI DSP TMS320F2812 is used to realize the algorithm.

Optimization of hydrometric monitoring network in urban drainage systems using information theory.

Science.gov (United States)

Yazdi, J

2017-10-01

Regular and continuous monitoring of urban runoff in both quality and quantity aspects is of great importance for controlling and managing surface runoff. Due to the considerable costs of establishing new gauges, optimization of the monitoring network is essential. This research proposes an approach for site selection of new discharge stations in urban areas, based on entropy theory in conjunction with multi-objective optimization tools and numerical models. The modeling framework provides an optimal trade-off between the maximum possible information content and the minimum shared information among stations. This approach was applied to the main surface-water collection system in Tehran to determine new optimal monitoring points under the cost considerations. Experimental results on this drainage network show that the obtained cost-effective designs noticeably outperform the consulting engineers' proposal in terms of both information contents and shared information. The research also determined the highly frequent sites at the Pareto front which might be important for decision makers to give a priority for gauge installation on those locations of the network.

Image-based environmental monitoring sensor application using an embedded wireless sensor network.

Science.gov (United States)

Paek, Jeongyeup; Hicks, John; Coe, Sharon; Govindan, Ramesh

2014-08-28

This article discusses the experiences from the development and deployment of two image-based environmental monitoring sensor applications using an embedded wireless sensor network. Our system uses low-power image sensors and the Tenet general purpose sensing system for tiered embedded wireless sensor networks. It leverages Tenet's built-in support for reliable delivery of high rate sensing data, scalability and its flexible scripting language, which enables mote-side image compression and the ease of deployment. Our first deployment of a pitfall trap monitoring application at the James San Cannot Mountain Reserve provided us with insights and lessons learned into the deployment of and compression schemes for these embedded wireless imaging systems. Our three month-long deployment of a bird nest monitoring application resulted in over 100,000 images collected from a 19-camera node network deployed over an area of 0.05 square miles, despite highly variable environmental conditions. Our biologists found the on-line, near-real-time access to images to be useful for obtaining data on answering their biological questions.

Image-Based Environmental Monitoring Sensor Application Using an Embedded Wireless Sensor Network

Directory of Open Access Journals (Sweden)

Jeongyeup Paek

2014-08-01

Full Text Available This article discusses the experiences from the development and deployment of two image-based environmental monitoring sensor applications using an embedded wireless sensor network. Our system uses low-power image sensors and the Tenet general purpose sensing system for tiered embedded wireless sensor networks. It leverages Tenet’s built-in support for reliable delivery of high rate sensing data, scalability and its flexible scripting language, which enables mote-side image compression and the ease of deployment. Our first deployment of a pitfall trap monitoring application at the James San Jacinto Mountain Reserve provided us with insights and lessons learned into the deployment of and compression schemes for these embedded wireless imaging systems. Our three month-long deployment of a bird nest monitoring application resulted in over 100,000 images collected from a 19-camera node network deployed over an area of 0.05 square miles, despite highly variable environmental conditions. Our biologists found the on-line, near-real-time access to images to be useful for obtaining data on answering their biological questions.

Development of the Nation-Wide Dosimetric Monitoring Network in Ukraine

International Nuclear Information System (INIS)

Chumak, V.; Boguslavskaya, A.; Musijachenko, A.

2004-01-01

Development of the nation-wide network for monitoring and registration of individual doses is being in progress in Ukraine. The need for urgent action is caused by the fact, that despite wide use of nuclear energy and radiation sources in industry and medicine, there is no centralized dose accounting system in Ukraine, existing dosimetry services operate obsolete manual TLD readers and no methodological unity is observed by the dosimetry services. Presently the mixed dosimetric monitoring is practiced in Ukraine. Nuclear power plants and some major nuclear facilities have their own dosimetry services responsible for dosimetric monitoring of workers. Rest of occupationally exposed persons is monitored by territorial dosimetry laboratories affiliated to sanitary and epidemiology supervision bodies. In total these services cover about 38,000 occupationally exposed workers, including 5,500 in medicine, 16,400 employees of five nuclear power plants and about 16,000 workers dealing with other sources of occupational exposure (industry, research, military). It is prescribed by the governmental decree that three-level united state system assigned to covering all aspects of efficient dosimetric monitoring should be established. The tasks of the system, in particular, are: securing methodical unity of individual dosimetric monitoring; scientific and methodological guidance of individual dosimetric control; procurement of common technical policy regarding nomenclature and operation of instrumentation; implementation of quality assurance programs; development and support of information infrastructure for logging, storage and access to data on individual dosimetric monitoring, in particular - keeping the national registry of individual doses; training and certification of personnel engaged in the system of individual dosimetric monitoring. In its development, the national system will be guided by international experience and will be established according to the best practices

Development of an Embedded Networked Sensing System for Structural Health Monitoring

OpenAIRE

Whang, Daniel; Xu, Ning; Rangwala, Sumit; Chintalapudi, Krishna; Govindan, Ramesh; Wallace, J W

2004-01-01

An innovative networked embedded sensing system for structural health monitoring is currently being developed. This sensor network has been prototyped in the laboratory, and will be deployed in a series of forced-vibration tests involving a full-scale, four-story office building in the next coming months. The low-power wireless seismic sensor system enables the acquisition of 15–30 channels of 16-bit accelerometer data at 128 Hz over a wireless network. The advantage of such a system is its t...

A Flexible Acoustic Sensor Network for Various Monitoring Applications

NARCIS (Netherlands)

Basten, T.G.H.; Wessels, P.W.

2013-01-01

Acoustic monitoring using a sensor network is a powerful instrument to assess and manage complex noise situations. It can provide a basis to identify appropriate and cost effective measures, and to assess their effect by comparing before and after implementation. It can also be an instrument for

Monitoring burst (M-burst) — A novel framework of failure localization in all-optical mesh networks

KAUST Repository

Ali, Mohammed L.; Ho, Pin-Han; Wu, Bin; Tapolcai, Janos; Shihada, Basem

2011-01-01

Achieving instantaneous and precise failure localization in all-optical wavelength division multiplexing (WDM) networks has been an attractive feature of network fault management systems, and is particularly important when failure-dependent protection is employed. The paper introduces a novel framework of real-time failure localization in all-optical WDM mesh networks, called monitoring-burst (m-burst), which aims to initiate a graceful compromise between consumed monitoring resources and monitoring delay. Different from any previously reported solution, the proposed m-burst framework has a single monitoring node (MN) which launches optical bursts along a set of pre-defined close-loop routes, called monitoring cycles (m-cycles), to probe the links along the m-cycles. Bursts along different m-cycles are kept non-overlapping through any link of the network. By identifying the lost bursts due to single link failure events only, the MN can unambiguously localize the failed link in at least 3-connected networks. We will justify the feasibility and applicability of the proposed m-burst framework in the scenario of interest. To avoid possible collision among optical bursts launched by the MN, we define the problem of collision-free scheduling and formulate it into an integer linear program (ILP) in order to minimize the monitoring delay. Numerical results demonstrate the effectiveness of the proposed framework and the proposed solution.

Monitoring burst (M-burst) — A novel framework of failure localization in all-optical mesh networks

KAUST Repository

Ali, Mohammed L.

2011-10-10

Achieving instantaneous and precise failure localization in all-optical wavelength division multiplexing (WDM) networks has been an attractive feature of network fault management systems, and is particularly important when failure-dependent protection is employed. The paper introduces a novel framework of real-time failure localization in all-optical WDM mesh networks, called monitoring-burst (m-burst), which aims to initiate a graceful compromise between consumed monitoring resources and monitoring delay. Different from any previously reported solution, the proposed m-burst framework has a single monitoring node (MN) which launches optical bursts along a set of pre-defined close-loop routes, called monitoring cycles (m-cycles), to probe the links along the m-cycles. Bursts along different m-cycles are kept non-overlapping through any link of the network. By identifying the lost bursts due to single link failure events only, the MN can unambiguously localize the failed link in at least 3-connected networks. We will justify the feasibility and applicability of the proposed m-burst framework in the scenario of interest. To avoid possible collision among optical bursts launched by the MN, we define the problem of collision-free scheduling and formulate it into an integer linear program (ILP) in order to minimize the monitoring delay. Numerical results demonstrate the effectiveness of the proposed framework and the proposed solution.

Toward implementation of a national ground water monitoring network

Science.gov (United States)

Schreiber, Robert P.; Cunningham, William L.; Copeland, Rick; Frederick, Kevin D.

2008-01-01

The Federal Advisory Committee on Water Information's (ACWI) Subcommittee on Ground Water (SOGW) has been working steadily to develop and encourage implementation of a nationwide, long-term ground-water quantity and quality monitoring framework. Significant progress includes the planned submission this fall of a draft framework document to the full committee. The document will include recommendations for implementation of the network and continued acknowledgment at the federal and state level of ACWI's potential role in national monitoring toward an improved assessment of the nation's water reserves. The SOGW mission includes addressing several issues regarding network design, as well as developing plans for concept testing, evaluation of costs and benefits, and encouraging the movement from pilot-test results to full-scale implementation within a reasonable time period. With the recent attention to water resource sustainability driven by severe droughts, concerns over global warming effects, and persistent water supply problems, the SOGW mission is now even more critical.

Environmental surveillance data report for the first quarter of 1986

International Nuclear Information System (INIS)

1986-07-01

The Department of Environmental Management (DEM) within the Environmental and Occupational Safety Division (E and OS) at the Oak Ridge National Laboratory (ORNL) is responsible for environmental surveillance to: (1) assure compliance with all Federal, State, and local standards for the prevention, control, and abatement of environmental pollution, (2) monitor the adequacy of containment and effluent controls, and (3) assess impacts on the environment of releases from ORNL facilities. During 1986, the Low-Level Counting Facility at ORNL began reporting radionuclide measurements in a manner different from that of previous years. Prior to 1986, data below the minimum detectable limit were reported as ''less than (<)'' the detection limit. This year, results that are negative (samples less than instrument background) are reported. If these data are compared to previous years, it will appear that average values for 1986 have decreased. Apparent decreases may be attributed to the reporting of negative values and the subsequent averaging of this data. Nonradionuclide results that are below the analytical detection limit are expressed as less than (<) the limit. In computing average values, sample results below the limit are assigned the limit, and the resulting average value is expressed as less than the computed value. The Four-Plant Analytical Committee is reviewing the standardization of reporting of less than detectable values. Their recommendations will be incorporated in these reports as they become policy

NORDITA report 1981

International Nuclear Information System (INIS)

1981-01-01

The purpose of Nordita is to encourage scientific collaboration between the Nordic countries within scientific and basic nuclear physics. The scientific programme at Nordita covers astrophysics, elementary particle physics, solid state physics and nuclear physics. This report covers the period January 1st - December 31st 1981. (Auth.)

Prairie Monitoring Protocol Development: North Coast and Cascades Network

Science.gov (United States)

McCoy, Allen; Dalby, Craig

2009-01-01

The purpose of the project was to conduct research that will guide development of a standard approach to monitoring several components of prairies within the North Coast and Cascades Network (NCCN) parks. Prairies are an important element of the natural environment at many parks, including San Juan Island National Historical Park (NHP) and Ebey's Landing National Historical Reserve (NHR). Forests have been encroaching on these prairies for many years, and so monitoring of the prairies is an important resource issue. This project specifically focused on San Juan Island NHP. Prairies at Ebey's Landing NHR will be monitored in the future, but that park was not mapped as part of this prototype project. In the interest of efficiency, the Network decided to investigate two main issues before launching a full protocol development effort: (1) the imagery requirements for monitoring prairie components, and (2) the effectiveness of software to assist in extracting features from the imagery. Several components of prairie monitoring were initially identified as being easily tracked using aerial imagery. These components included prairie/forest edge, broad prairie composition (for example, shrubs, scattered trees), and internal exclusions (for example, shrubs, bare ground). In addition, we believed that it might be possible to distinguish different grasses in the prairies if the imagery were of high enough resolution. Although the areas in question at San Juan Island NHP are small enough that mapping on the ground with GPS (Global Positioning System) would be feasible, other applications could benefit from aerial image acquisition on a regular, recurring basis and thereby make the investment in aerial imagery worthwhile. The additional expense of orthorectifying the imagery also was determined to be cost-effective.

Physics, Computer Science and Mathematics Division annual report, 1 January-31 December 1981

International Nuclear Information System (INIS)

Birge, R.W.

1982-12-01

This report summarizes the research performed in the Physics, Computer Science and Mathematics Division of the Lawrence Berkeley Laboratory during calendar year 1981. During the year under review the Division devoted roughly half its effort to the final construction stages of the Time Projection Chamber and other equipment for the PEP-4 facility at SLAC. The year was marked by the successful passage of milestone after milestone - the two-sector test of the TPC with cosmic rays in July 1981, the full TPC test in November 1981, and the roll-in onto the PEP beam line on 6 January 1982. In other e + e - experiments, the Mark II detector continued its productive data-taking at PEP. In other areas, the final stages of data analysis, particularly for the structure functions, proceeded for the inelastic muon scattering experiment performed at Fermilab, a muon polarimeter experiment was developed and mounted at TRIUMF to probe for the presence of right-handed currents in muon decay, and the design and then construction began of fine-grained hadron calorimeters for the end caps of the Colliding Detector Facility at Fermilab. The Particle Data Group intensified its activities, despite financial constraints, as it proceeded toward production of a new edition of its authoritative Review of Particle Properties early in 1982. During 1981 the Theoretical Physics Group pursued a diverse spectrum of research in its own right and also interacted effectively with the experimental program. Research and development continued on the segmented mirror for the ten-meter telescope proposed by the University of California. Activities in the Computer Science and Mathematics Department encompassed networking, database management, software engineering, and computer graphics, as well as basic research in nonlinear phenomena in combustion and fluid flow

Physics, Computer Science and Mathematics Division annual report, 1 January-31 December 1981

Energy Technology Data Exchange (ETDEWEB)

Birge, R.W.

1982-12-01

This report summarizes the research performed in the Physics, Computer Science and Mathematics Division of the Lawrence Berkeley Laboratory during calendar year 1981. During the year under review the Division devoted roughly half its effort to the final construction stages of the Time Projection Chamber and other equipment for the PEP-4 facility at SLAC. The year was marked by the successful passage of milestone after milestone - the two-sector test of the TPC with cosmic rays in July 1981, the full TPC test in November 1981, and the roll-in onto the PEP beam line on 6 January 1982. In other e/sup +/e/sup -/ experiments, the Mark II detector continued its productive data-taking at PEP. In other areas, the final stages of data analysis, particularly for the structure functions, proceeded for the inelastic muon scattering experiment performed at Fermilab, a muon polarimeter experiment was developed and mounted at TRIUMF to probe for the presence of right-handed currents in muon decay, and the design and then construction began of fine-grained hadron calorimeters for the end caps of the Colliding Detector Facility at Fermilab. The Particle Data Group intensified its activities, despite financial constraints, as it proceeded toward production of a new edition of its authoritative Review of Particle Properties early in 1982. During 1981 the Theoretical Physics Group pursued a diverse spectrum of research in its own right and also interacted effectively with the experimental program. Research and development continued on the segmented mirror for the ten-meter telescope proposed by the University of California. Activities in the Computer Science and Mathematics Department encompassed networking, database management, software engineering, and computer graphics, as well as basic research in nonlinear phenomena in combustion and fluid flow.

Realization of hiberarchy wireless sensor network for mine laneway monitoring

Energy Technology Data Exchange (ETDEWEB)

Yang Wei; Wang Bin [Beijing Jiaotong University, Beijing (China). Key Laboratory of All Optical Network and Advanced Telecommunications Network

2008-01-15

According to the requirement of monitoring the environment of coal mine laneways and the characteristics of laneway land form, a kind of hiberarchy wireless sensor network was proposed for laneway monitoring. The topology control mechanism and routing mechanism were designed, corresponding hardware of the sensor node and the protocol stack were developed and two work modes for the system were designed. Simulation experiment in the laboratory proved to operate well; the data exceeding the threshold could be timely delivered in interrupt mode and data could be periodically gathered steadily and reliably in period monitor mode. 6 refs., 7 figs.

The communications in early warning network for radiation monitoring

International Nuclear Information System (INIS)

Oyoun, M.B.; Al-Hussin, Mohamad; Fares, Adnan; Al-Oulabi, Yasser; Othman, Ibrahim

1992-07-01

The objectives of early warning network are: The determination of gamma radiation (background) levels in air which depend on location and time, evaluation of any situation resulting from radiation or nuclear accident out of boarder, and after that reporting the emergency situation to relevant authorities on the national and international levels. Monitoring stations were installed using Gm tubes to cover boarder lines from south to north and east to west as follows: Damascus, Darra, Latakia, Tartous, Aleppo, Kamishly, Ragaa, and Qunitra. The following modes of communication: Telephone line, leased line, direct connection, and Syrian data network were used in the Syrian early network. This project was carried out in cooperation with IAEA under project no. RER/9/003. (author). 22 figs., 1 tab

Coded-subcarrier-aided chromatic dispersion monitoring scheme for flexible optical OFDM networks.

Science.gov (United States)

Tse, Kam-Hon; Chan, Chun-Kit

2014-08-11

A simple coded-subcarrier aided scheme is proposed to perform chromatic dispersion monitoring in flexible optical OFDM networks. A pair of coded label subcarriers is added to both edges of the optical OFDM signal spectrum at the edge transmitter node. Upon reception at any intermediate or the receiver node, chromatic dispersion estimation is performed, via simple direct detection, followed by electronic correlation procedures with the designated code sequences. The feasibility and the performance of the proposed scheme have been experimentally characterized. It provides a cost-effective monitoring solution for the optical OFDM signals across intermediate nodes in flexible OFDM networks.

Combine harvester monitor system based on wireless sensor network

Science.gov (United States)

A measurement method based on Wireless Sensor Network (WSN) was developed to monitor the working condition of combine harvester for remote application. Three JN5139 modules were chosen for sensor data acquisition and another two as a router and a coordinator, which could create a tree topology netwo...

Active Low Intrusion Hybrid Monitor for Wireless Sensor Networks.

Science.gov (United States)

Navia, Marlon; Campelo, Jose C; Bonastre, Alberto; Ors, Rafael; Capella, Juan V; Serrano, Juan J

2015-09-18

Several systems have been proposed to monitor wireless sensor networks (WSN). These systems may be active (causing a high degree of intrusion) or passive (low observability inside the nodes). This paper presents the implementation of an active hybrid (hardware and software) monitor with low intrusion. It is based on the addition to the sensor node of a monitor node (hardware part) which, through a standard interface, is able to receive the monitoring information sent by a piece of software executed in the sensor node. The intrusion on time, code, and energy caused in the sensor nodes by the monitor is evaluated as a function of data size and the interface used. Then different interfaces, commonly available in sensor nodes, are evaluated: serial transmission (USART), serial peripheral interface (SPI), and parallel. The proposed hybrid monitor provides highly detailed information, barely disturbed by the measurement tool (interference), about the behavior of the WSN that may be used to evaluate many properties such as performance, dependability, security, etc. Monitor nodes are self-powered and may be removed after the monitoring campaign to be reused in other campaigns and/or WSNs. No other hardware-independent monitoring platforms with such low interference have been found in the literature.

Operational monitoring of acoustic sensor networks

Directory of Open Access Journals (Sweden)

Boltenkov V.A.

2015-06-01

Full Text Available Acoustic sensor networks (ASN are widely used to monitor water leaks in the power generating systems. Since the ASN are used in harsh climatic conditions the failures of microphone elements of ASN are inevitable. That's why the failure detection of ASN elements is a problem of current interest. Two techniques of operational monitoring ASN are developed. Both of them are based on the placement of the test sound source within a network. The signal processing for ASN sensors had to detect the failed element. Techniques are based time difference of arrival (TDOA estimating at the each pair of ASN elements. TDOA estimates as argmaximum of cross-correlation function (CCF for signals on each microphone sensors pair. The M-sequence phase-shift keyed signal is applied as a test acoustic signal to ensure high accuracy of the CCF maximum estimation at low signal/noise ratio (SNR. The first technique is based on the isolation principle for TDOA sum at three points. It require to locate the test sound source in the far field. This is not always possible due to technological reasons. For the second proposed technique test sound source can be located near the ASN. It is based on a system of hyperbolic equations solving for each of the four elements of the ASN. Both techniques has been tested in the computer imitation experiment. It was found that for the SNR to –5 dB both techniques show unmistakable indicators of control quality. The second method requires significantly more time control.

Airborne Wireless Sensor Networks for Airplane Monitoring System

Directory of Open Access Journals (Sweden)

Shang Gao

2018-01-01

Full Text Available In traditional airplane monitoring system (AMS, data sensed from strain, vibration, ultrasound of structures or temperature, and humidity in cabin environment are transmitted to central data repository via wires. However, drawbacks still exist in wired AMS such as expensive installation and maintenance, and complicated wired connections. In recent years, accumulating interest has been drawn to performing AMS via airborne wireless sensor network (AWSN system with the advantages of flexibility, low cost, and easy deployment. In this review, we present an overview of AMS and AWSN and demonstrate the requirements of AWSN for AMS particularly. Furthermore, existing wireless hardware prototypes and network communication schemes of AWSN are investigated according to these requirements. This paper will improve the understanding of how the AWSN design under AMS acquires sensor data accurately and carries out network communication efficiently, providing insights into prognostics and health management (PHM for AMS in future.

Meningen over abortus in West-Europa, 1981-2000

NARCIS (Netherlands)

Need, Ariana; Ultee, Wouter; Levels, Mark; Tienen, Marike van

2008-01-01

Summary Abortion attitudes in Western Europe, 1981-2000 This article answers descriptive and explanatory questions about abortion attitudes in Western Europe between 1981 and 2000. It explains country differences and trends in these attitudes with abortion laws of states, with the norms that prevail

Annual report 1981-82

International Nuclear Information System (INIS)

The research and teaching programmes of the Universities Research Reactor, Risley, U.K. are reviewed giving outlines of the individual experiments undertaken during 1981-82 and the reactor operation and safety arrangements. (U.K.)

Landslide Monitoring Network Establishment within Unified Datum and Stability Analysis in the Three Gorges Reservoir Area

Directory of Open Access Journals (Sweden)

Shengxiang Huang

2017-01-01

Full Text Available A landslide monitoring network construction within unified datum which combined fiducial points, working reference points, and monitoring points was intensively studied in the Three Gorges Reservoir area. With special long and narrow geographical location in the area, designing and building monitoring network was vital to the realization of landslide monitoring. To build such a network with high precision, this paper mainly focused on the following four aspects: (1 method of using multiple GPS reference stations to build a unified datum network and subnet adjustment, (2 GPS data processing algorithm with millimeter level, (3 analysis of influence on the adjustment resulting from systematic error of time evolution datum from different GPS observations, and (4 establishment and stability analysis of unified datum. Then, using global test and trial-and-error method to analyze the datum based on the GPS observations (2008~2011 of landslide monitoring network in the area, we concluded that there were moved reference points during the three years of high water impoundment, and the horizontal displacement of moved reference points was more than 4 cm, even up to 79.4 cm. The displacement direction of unstable reference points was inspected with geographical environment at sites, which revealed congruency between them.

A distributed multiagent system architecture for body area networks applied to healthcare monitoring.

Science.gov (United States)

Felisberto, Filipe; Laza, Rosalía; Fdez-Riverola, Florentino; Pereira, António

2015-01-01

In the last years the area of health monitoring has grown significantly, attracting the attention of both academia and commercial sectors. At the same time, the availability of new biomedical sensors and suitable network protocols has led to the appearance of a new generation of wireless sensor networks, the so-called wireless body area networks. Nowadays, these networks are routinely used for continuous monitoring of vital parameters, movement, and the surrounding environment of people, but the large volume of data generated in different locations represents a major obstacle for the appropriate design, development, and deployment of more elaborated intelligent systems. In this context, we present an open and distributed architecture based on a multiagent system for recognizing human movements, identifying human postures, and detecting harmful activities. The proposed system evolved from a single node for fall detection to a multisensor hardware solution capable of identifying unhampered falls and analyzing the users' movement. The experiments carried out contemplate two different scenarios and demonstrate the accuracy of our proposal as a real distributed movement monitoring and accident detection system. Moreover, we also characterize its performance, enabling future analyses and comparisons with similar approaches.

The International Monitoring System's Noble Gas Network

International Nuclear Information System (INIS)

Auer, M.

2015-01-01

The International Monitoring System (IMS) is a unique global network for surveillance of the Comprehensive Nuclear-Test-Ban Treaty. A major component of the IMS is the radionuclide monitoring network since, among all IMS technologies, it can provide the most unequivocal evidence for a nuclear explosion. The radionuclide monitoring component is unprecedented in its combination of global coverage, sensitivity, network density and temporal resolution. In particular for the detection of underground or underwater nuclear tests, forty of the eighty radionuclide stations will eventually be equipped with sensors to measure the Xenon isotopes Xe-131m (τ 1/2 = 11:8 d), Xe-133 (τ 1/2 = 5:25 d), Xe-133m (τ 1/2 = 2:2 d) and Xe-135 (τ 1/2 = 9:14 h). These are among the isotopes with the highest yields in fission of uranium or plutonium with half-lives long enough to be detected at large distances from the point of emission. As of today, 31 noble gas systems have been installed and are sending data to the International Data Centre. The noble gas systems installed at the stations are automated and sample Xenon continuously from atmospheric air for 12 or 24 hours at an air flow of 0.5 to several m 3 /h by absorption of Xenon on activated charcoal. Detection of the Xenon isotopes is either by high resolution gamma spectrometry or by beta-gamma coincidence spectrometry. With the currently available equipment, detection limits of 0.2 mBq/m 3 can be achieved. An overview on the existing technology and future developments as well as on the interpretation of measurement results is given. (author)

NRC TLD [Nuclear Regulatory Commission thermoluminescent dosimeter] direct radiation monitoring network

International Nuclear Information System (INIS)

Struckmeyer, R.; McNamara, N.

1990-03-01

This report presents the results of the NRC Direct Radiation Monitoring Network for the fourth quarter of 1989. It provides the ambient radiation levels measured in the vicinity of 75 sites throughout the United States. In addition, it describes the equipment used, monitoring station selection criteria, characterization of the dosimeter response, calibration procedures, statistical methods, intercomparison, and quality assurance program

Towards development of a deposition monitoring network for air pollution of Europe

NARCIS (Netherlands)

Erisman JW; Mennen MG; Fowler D; Flechard CR; Spindler G; Gruner A; Duyzer JH; Ruigrok W; Wyers GP; LLO; TNO; ECN; ITE (Engeland); IFT (Duitsland)

1996-01-01

In January 1993 within the framework of the LIFE programme a project was financed which aim was to develop a deposition monitoring method for air pollution of Europe. This method should be used to extend existing European monitoring networks of air concentrations to provide deposition inputs on an

Using Geoscience and Geostatistics to Optimize Groundwater Monitoring Networks at the Savannah River Site

International Nuclear Information System (INIS)

Tuckfield, R.C.

2001-01-01

A team of scientists, engineers, and statisticians was assembled to review the operation efficiency of groundwater monitoring networks at US Department of Energy Savannah River Site (SRS). Subsequent to a feasibility study, this team selected and conducted an analysis of the A/M area groundwater monitoring well network. The purpose was to optimize the number of groundwater wells requisite for monitoring the plumes of the principal constituent of concern, viz., trichloroethylene (TCE). The project gathered technical expertise from the Savannah River Technology Center (SRTC), the Environmental Restoration Division (ERD), and the Environmental Protection Department (EPD) of SRS

Twenty-fifth annual report 1981

International Nuclear Information System (INIS)

1982-01-01

In this report progress for 1981 is reported on the following: nuclear materials; nuclear power; application of radioisotopes and radiation; health and safety; fundamental studies undertaken in the fields of nuclear physics, plasma physics, theoretical physics, radiation chemistry, research on liquid metals and molten salts, solid-state physics and the medical and biological sciences. The supporting activities of the research reactor, electronic engineering, waste treatment and disposal, decontamination services, analytical services, engineering services and computing services are discussed. The activities of the external relations division and licensing division are also discussed. The report contains a bibliography of publications published by staff members and bursars of the Atomic Energy Board during 1981

An intelligent service matching method for mechanical equipment condition monitoring using the fibre Bragg grating sensor network

Science.gov (United States)

Zhang, Fan; Zhou, Zude; Liu, Quan; Xu, Wenjun

2017-02-01

Due to the advantages of being able to function under harsh environmental conditions and serving as a distributed condition information source in a networked monitoring system, the fibre Bragg grating (FBG) sensor network has attracted considerable attention for equipment online condition monitoring. To provide an overall conditional view of the mechanical equipment operation, a networked service-oriented condition monitoring framework based on FBG sensing is proposed, together with an intelligent matching method for supporting monitoring service management. In the novel framework, three classes of progressive service matching approaches, including service-chain knowledge database service matching, multi-objective constrained service matching and workflow-driven human-interactive service matching, are developed and integrated with an enhanced particle swarm optimisation (PSO) algorithm as well as a workflow-driven mechanism. Moreover, the manufacturing domain ontology, FBG sensor network structure and monitoring object are considered to facilitate the automatic matching of condition monitoring services to overcome the limitations of traditional service processing methods. The experimental results demonstrate that FBG monitoring services can be selected intelligently, and the developed condition monitoring system can be re-built rapidly as new equipment joins the framework. The effectiveness of the service matching method is also verified by implementing a prototype system together with its performance analysis.

Wireless Networked Sensors for Remote Monitoring in Propulsion Systems, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This NASA Phase I SBIR program would fabricate wireless networked nanomembrane (NM) based surface pressure sensors for remote monitoring in propulsion systems, using...

Deploying Monitoring Trails for Fault Localization in All- Optical Networks and Radio-over-Fiber Passive Optical Networks

Science.gov (United States)

Maamoun, Khaled Mohamed

Fault localization is the process of realizing the true source of a failure from a set of collected failure notifications. Isolating failure recovery within the network optical domain is necessary to resolve alarm storm problems. The introduction of the monitoring trail (m-trail) has been proven to deliver better performance by employing monitoring resources in a form of optical trails - a monitoring framework that generalizes all the previously reported counterparts. In this dissertation, the m-trail design is explored and a focus is given to the analysis on using m-trails with established lightpaths to achieve fault localization. This process saves network resources by reducing the number of the m-trails required for fault localization and therefore the number of wavelengths used in the network. A novel approach based on Geographic Midpoint Technique, an adapted version of the Chinese Postman's Problem (CPP) solution and an adapted version of the Traveling Salesman's Problem (TSP) solution algorithms is introduced. The desirable features of network architectures and the enabling of innovative technologies for delivering future millimeter-waveband (mm-WB) Radio-over-Fiber (RoF) systems for wireless services integrated in a Dense Wavelength Division Multiplexing (DWDM) is proposed in this dissertation. For the conceptual illustration, a DWDM RoF system with channel spacing of 12.5 GHz is considered. The mm-WB Radio Frequency (RF) signal is obtained at each Optical Network Unit (ONU) by simultaneously using optical heterodyning photo detection between two optical carriers. The generated RF modulated signal has a frequency of 12.5 GHz. This RoF system is easy, cost-effective, resistant to laser phase noise and also reduces maintenance needs, in principle. A revision of related RoF network proposals and experiments is also included. A number of models for Passive Optical Networks (PON)/ RoF-PON that combine both innovative and existing ideas along with a number of

Annual Report 1981

International Nuclear Information System (INIS)

1983-01-01

The advances in the execution of the Argentine Nuclear Program, performed by CNEA during 1981, are reported. The information is grouped in six sections: Nuclear Power Plants, Supplies to Nuclear Power Plants, Radioisotopes and Radiations, Research and Development, Radiological Protection and Nuclear Safety, and Infrastructure and General Aspects. (M.E.L.) [es

NRC TLD Direct Radiation Monitoring Network. Volume 5, No. 2. Progress report, April-June 1985

International Nuclear Information System (INIS)

Jang, J.; Kramaric, M.; Cohen, L.

1985-09-01

The US Nuclear Regulatory Commission (NRC) Direct Radiation Monitoring Network provides continuous measurement of the ambient radiation levels around licensed NRC facilities, primarily power reactors. The Network is intended to measure radiation levels during routine facility operations and to establish background radiation levels used to assess the radiological impact of an unusual condition, such as an accident. This report presents the radiation levels measured around all facilities in the Network for the second quarter of 1985. A complete listing of the site facilities monitored is included

Summary of activities July 1981 - July 1982

International Nuclear Information System (INIS)

1982-07-01

Background information, which may be useful for an understanding of ECN activities has been reported. The period starting 1 July 1981 and ending 30 June 1982 covers summaries of fission power, fusion and superconductivity; energy from fossil fuels; wind energy; utilization of the Petten research reactors. The financial figures are taken from the ECN Annual report (in Dutch) and refer to the calender year 1981

Co-ordinated research and environmental surveillance programme related to sea disposal of radioactive waste CRESP activity report 1986-1990

International Nuclear Information System (INIS)

1990-01-01

The Co-ordinated Research and Environmental Surveillance Programme relevant to sea disposal of radioactive waste (CRESP) was created in 1981 in the framework of the 1977 Decision of the OECD Council establishing a Multilateral Consultation and Surveillance Mechanism for Sea Dumping of Radioactive Waste. The main task of CRESP was to set up a site-specific scientific research programme to increase current knowledge of the processes controlling the transfer of radionuclides in the marine environment, so that impact of past dumping could be monitored and future assessments could be based on more accurate and comprehensive scientific data. The CRESP mandate was extended in 1987 to respond to a request from the Paris Commission to include consideration of radioactive discharges in the maritime area covered by the Convention on the Prevention of Marine Pollution from Land-Based Sources. This report summarizes the CRESP activities carried out during the 1986-1990 five year phase. Concerning the review of deep sea results, the report relates progress achieved above the level of knowledge which was available when the present phase of the CRESP programme was decided and which has been taken into account in the 1985 Site Suitability Review. With respect to coastal discharges, it presents a summary of R and D work undertaken by member countries, including those carried out in other programmes such as MARINA. Finally, it makes proposals for future work within CRESP

Indigenous development and networking of online radon monitors in the underground uranium mine

International Nuclear Information System (INIS)

Gaware, J.J.; Sahoo, B.K.; Sapra, B.K.; Mayya, Y.S.

2011-01-01

There has been a long standing demand for online monitoring of radon level in various locations of underground Uranium mine for taking care of radiological protection to workers. Nowadays, radon ( 222 Rn) monitors, based on electrostatic collection of charged progeny and subsequent detection by semiconductor detector are increasingly employed for radon monitoring in environment. However, such instruments have some limitations such as (i) requirement of additional dryer since sensitivity is dependent on the humidity (ii) cannot be connected to a network and (iii) not cost effective etc. Hence use of such instruments in underground uranium mine (humidity level >90), may not be reliable. Towards this end, we have indigenously developed radon monitor based on electrostatic collection and scintillation technology for the online monitoring in uranium mine. This instrument overcomes the above mentioned limitation of commercial radon monitors and based on custom made features. Different tests and measurements were carried out and compared with commercial instruments. It was found to be in an excellent agreement with the commercial instruments. A few such instruments have been installed in different locations of uranium mine at Turamdih and connected to a network system for online monitoring and display. (author)

Hazelwood Interim Storage Site annual site environmental report: Calendar year 1986

International Nuclear Information System (INIS)

1987-06-01

During 1986, the environmental monitoring program was continued at the Hazelwood Interim Storage Site (HISS), a US Department of Energy (DOE) facility located in the City of Hazelwood, Missouri. Originally known as the Cotter Corporation site on Latty Avenue in Hazelwood, the HISS is presently used for the storage of soils contaminated with residual radioactive material. As part of the decontamination research and development project authorized by Congress under the 1984 Energy and Water Appropriations Act, remedial action and environmental monitoring program are being conducted at the site and at vicinity properties by Bechtel National, Inc., Project Management Contractor for FUSRAP. The monitoring program at the HISS measures radon gas concentrations in air; external gamma radiation levels; and uranium, radium, and thorium concentrations in surface water, groundwater, and sediment. To verify that the site is in compliance with the DOE radiation protection standard (100 mrem/yr) and assess its potential effect on public health, the radiation dose was calculated for the maximally exposed individual. Based on the scenario described in this report, the maximally exposed individual at the HISS would receive an annual external exposure approximately equivalent to 2% of the DOE radiation protection standard of 100 mrem/yr. This exposure is less than the exposure a person would receive during a round-trip flight from New York to Los Angeles. The cumulative dose to the population within an 80-km (50-mi) radius of the HISS that would result from radioactive materials present at the site would be indistinguishable from the dose that the same population would receive from naturally occurring radioactive sources. Results of the 1986 monitoring show that the HISS is in compliance with the DOE radiation protection standard. 11 refs., 6 figs., 10 tabs

A Bayesian maximum entropy-based methodology for optimal spatiotemporal design of groundwater monitoring networks.

Science.gov (United States)

Hosseini, Marjan; Kerachian, Reza

2017-09-01

This paper presents a new methodology for analyzing the spatiotemporal variability of water table levels and redesigning a groundwater level monitoring network (GLMN) using the Bayesian Maximum Entropy (BME) technique and a multi-criteria decision-making approach based on ordered weighted averaging (OWA). The spatial sampling is determined using a hexagonal gridding pattern and a new method, which is proposed to assign a removal priority number to each pre-existing station. To design temporal sampling, a new approach is also applied to consider uncertainty caused by lack of information. In this approach, different time lag values are tested by regarding another source of information, which is simulation result of a numerical groundwater flow model. Furthermore, to incorporate the existing uncertainties in available monitoring data, the flexibility of the BME interpolation technique is taken into account in applying soft data and improving the accuracy of the calculations. To examine the methodology, it is applied to the Dehgolan plain in northwestern Iran. Based on the results, a configuration of 33 monitoring stations for a regular hexagonal grid of side length 3600 m is proposed, in which the time lag between samples is equal to 5 weeks. Since the variance estimation errors of the BME method are almost identical for redesigned and existing networks, the redesigned monitoring network is more cost-effective and efficient than the existing monitoring network with 52 stations and monthly sampling frequency.

U.S. EPA's National Dioxin Air Monitoring Network: Analytical Issues

Science.gov (United States)

The U.S. EPA has established a National Dioxin Air Monitoring Network (NDAMN) to determine the temporal and geographical variability of atmospheric chlorinated dibenzo-p-dioxins (CDDs), furans (CDFs), and coplanar polychlorinated biphenyls (PCBs) at rural and non-impacted locatio...

European Marine Biodiversity Monitoring Networks: strengths, weaknesses, opportunities and threats

Directory of Open Access Journals (Sweden)

Joana Patrício

2016-09-01

Full Text Available By 2020, European Union Member States should achieve Good Environmental Status (GES for eleven environmental quality descriptors for their marine waters to fulfill the Marine Strategy Framework Directive (MSFD. By the end of 2015, in coordination with the Regional Seas Conventions, each EU Member States was required to develop a marine strategy for their waters, together with other countries within the same marine region or sub-region. Coherent monitoring programs, submitted in 2014, form a key component of this strategy, which then aimed to lead to a Program of Measures (submitted in 2015. The European DEVOTES FP7 project has produced and interrogated a catalogue of EU marine monitoring related to MSFD descriptors 1 (biological diversity, 2 (non-indigenous species, 4 (food webs and 6 (seafloor integrity. Here we detail the monitoring activity at the regional and sub-regional level for these descriptors, as well as for 11 biodiversity components, 22 habitats and the 37 anthropogenic pressures addressed. The metadata collated for existing European monitoring networks were subject to a SWOT (strengths, weaknesses, opportunities and threats analysis. This interrogation has indicated case studies to address the following questions: a what are the types of monitoring currently in place?; b who does what and how?; c is the monitoring fit-for-purpose for addressing the MSFD requirements?, and d what are the impediments to better monitoring (e.g. costs, shared responsibilities between countries, overlaps, co-ordination? We recommend the future means, to overcome the identified impediments and develop more robust monitoring strategies and as such the results are especially relevant to implementing coordinated monitoring networks throughout Europe, for marine policy makers, government agencies and regulatory bodies. It is emphasized that while many of the recommendations given here require better, more extensive and perhaps more costly monitoring, this is

Idaho field experiment 1981. Volume 2: measurement data

Energy Technology Data Exchange (ETDEWEB)

Start, G E; Sagendorf, J F; Ackermann, G R; Cate, J H; Hukari, N F; Dickson, C R

1984-04-01

The 1981 Idaho Field Experiment was conducted in southeastern Idaho over the upper Snake River Plain. Nine test-day case studies were conducted between July 15 and 30, 1981. Releases of SF/sub 6/ gaseous tracer were made for 8-hour periods from 46m above ground. Tracer was sampled hourly, for 12 sequential hours, at about 100 locations within an area 24km square. Also, a single total integrated sample of about 30 hours duration was collected at approximately 100 sites within an area 48 by 72km square (using 6km spacings). Extensive tower profiles of meteorology at the release point were collected. RAWINSONDES, RABALS and PIBALS were collected at 3 to 5 sites. Horizontal, low-altitude winds were monitored using the INEL MESONET. SF/sub 6/ tracer plume releases were marked with co-located oil fog releases and bi-hourly sequential launches of tetroon pairs. Aerial LIDAR observations of the oil fog plume and airborne samples of SF/sub 6/ were collected. High altitude aerial photographs of daytime plumes were collected. Volume II lists the data in tabular form or cites the special supplemental reports by other participating contractors. While the primary user file and the data archive are maintained on 9 track/1600 cpi magnetic tapes, listings of the individual values are provided for the user who either cannot utilize the tapes or wishes to preview the data. The accuracies and quality of these data are described.

Design of a monitoring network over France in case of a radiological accidental release

Science.gov (United States)

Abida, Rachid; Bocquet, Marc; Vercauteren, Nikki; Isnard, Olivier

The Institute of Radiation Protection and Nuclear Safety (France) is planning the set-up of an automatic nuclear aerosol monitoring network over the French territory. Each of the stations will be able to automatically sample the air aerosol content and provide activity concentration measurements on several radionuclides. This should help monitor the French and neighbouring countries nuclear power plants set. It would help evaluate the impact of a radiological incident occurring at one of these nuclear facilities. This paper is devoted to the spatial design of such a network. Here, any potential network is judged on its ability to extrapolate activity concentrations measured on the network stations over the whole domain. The performance of a network is quantitatively assessed through a cost function that measures the discrepancy between the extrapolation and the true concentration fields. These true fields are obtained through the computation of a database of dispersion accidents over one year of meteorology and originating from 20 French nuclear sites. A close to optimal network is then looked for using a simulated annealing optimisation. The results emphasise the importance of the cost function in the design of a network aimed at monitoring an accidental dispersion. Several choices of norm used in the cost function are studied and give way to different designs. The influence of the number of stations is discussed. A comparison with a purely geometric approach which does not involve simulations with a chemistry-transport model is performed.

Design of Mine Ventilators Monitoring System Based on Wireless Sensor Network

International Nuclear Information System (INIS)

Fu Sheng; Song Haiqiang

2012-01-01

A monitoring system for a mine ventilator is designed based on ZigBee wireless sensor network technology in the paper. The system consists of a sink node, sensor nodes, industrial personal computer and several sensors. Sensor nodes communicate with the sink node through the ZigBee wireless sensor network. The sink node connects with the configuration software on the pc via serial port. The system can collect or calculate vibration, temperature, negative pressure, air volume and other information of the mine ventilator. Meanwhile the system accurately monitors operating condition of the ventilator through these parameters. Especially it provides the most original information for potential faults of the ventilator. Therefore, there is no doubt that it improves the efficiency of fault diagnosis.

Design of Mine Ventilators Monitoring System Based on Wireless Sensor Network

Science.gov (United States)

Fu, Sheng; Song, Haiqiang

2012-05-01

A monitoring system for a mine ventilator is designed based on ZigBee wireless sensor network technology in the paper. The system consists of a sink node, sensor nodes, industrial personal computer and several sensors. Sensor nodes communicate with the sink node through the ZigBee wireless sensor network. The sink node connects with the configuration software on the pc via serial port. The system can collect or calculate vibration, temperature, negative pressure, air volume and other information of the mine ventilator. Meanwhile the system accurately monitors operating condition of the ventilator through these parameters. Especially it provides the most original information for potential faults of the ventilator. Therefore, there is no doubt that it improves the efficiency of fault diagnosis.

A Survey on Quality of Service Monitoring and Analysis of Network of Agricultural Science and Technology Resources

OpenAIRE

Jian , Ma

2014-01-01

International audience; First, current situation on Network of agricultural science and technology resources is described. Then we pay much attention to the quality of service monitoring and analysis system of network resources. And finally, we come to the conclusion that the construction of Quality of service monitoring, analysis of network of agricultural science and technology resources is in great need.

A pervasive health monitoring service system based on ubiquitous network technology.

Science.gov (United States)

Lin, Chung-Chih; Lee, Ren-Guey; Hsiao, Chun-Chieh

2008-07-01

The phenomenon of aging society has derived problems such as shortage of medical resources and reduction of quality in healthcare services. This paper presents a system infrastructure for pervasive and long-term healthcare applications, i.e. a ubiquitous network composed of wireless local area network (WLAN) and cable television (CATV) network serving as a platform for monitoring physiological signals. Users can record vital signs including heart rate, blood pressure, and body temperature anytime either at home or at frequently visited public places in order to create a personal health file. The whole system was formally implemented in December 2004. Analysis of 2000 questionnaires indicates that 85% of users were satisfied with the provided community-wide healthcare services. Among the services provided by our system, health consultation services offered by family doctors was rated the most important service by 17.9% of respondents, and was followed by control of one's own health condition (16.4% of respondents). Convenience of data access was rated most important by roughly 14.3% of respondents. We proposed and implemented a long-term healthcare system integrating WLAN and CATV networks in the form of a ubiquitous network providing a service platform for physiological monitoring. This system can classify the health levels of the resident according to the variation tendency of his or her physiological signal for important reference of health management.

NRC TLD Direct Radiation Monitoring Network. Progress report, October--December 1996

International Nuclear Information System (INIS)

Struckmeyer, R.

1997-03-01

This report presents the results of the NRC Direct Radiation Monitoring Network for the fourth quarter of 1996. It provides the ambient radiation levels measured in the vicinity of 74 sites throughout the United States. In addition, it describes the equipment used, monitoring station selection criteria, characterization of the dosimeter response, calibration procedures, statistical methods, intercomparison, and quality assurance program. 3 figs., 4 tabs

NRC TLD Direct Radiation Monitoring Network. Progress report, October--December 1996

Energy Technology Data Exchange (ETDEWEB)

Struckmeyer, R.

1997-03-01

This report presents the results of the NRC Direct Radiation Monitoring Network for the fourth quarter of 1996. It provides the ambient radiation levels measured in the vicinity of 74 sites throughout the United States. In addition, it describes the equipment used, monitoring station selection criteria, characterization of the dosimeter response, calibration procedures, statistical methods, intercomparison, and quality assurance program. 3 figs., 4 tabs.

A Mountain-Scale Monitoring Network for Yucca Mountain Performance Confirmation

International Nuclear Information System (INIS)

Freifeld, Barry; Tsang, Yvonne

2006-01-01

Confirmation of the performance of Yucca Mountain is required by 10 CFR Part 63.131 to indicate, where practicable, that the natural system acts as a barrier, as intended. Hence, performance confirmation monitoring and testing would provide data for continued assessment during the pre-closure period. In general, to carry out testing at a relevant scale is always important, and in the case of performance confirmation, it is particularly important to be able to test at the scale of the repository. We view the large perturbation caused by construction of the repository at Yucca Mountain as a unique opportunity to study the large-scale behavior of the natural barrier system. Repository construction would necessarily introduce traced fluids and result in the creation of leachates. A program to monitor traced fluids and construction leachates permits evaluation of transport through the unsaturated zone and potentially downgradient through the saturated zone. A robust sampling and monitoring network for continuous measurement of important parameters, and for periodic collection of agrochemical samples, is proposed to observe thermo-hydrogeochemical changes near the repository horizon and down to the water table. The sampling and monitoring network can be used to provide data to (1) assess subsurface conditions encountered and changes in those conditions during construction and waste emplacement operations; and (2) for modeling to determine that the natural system is functioning as intended

How to Decide? Multi-Objective Early-Warning Monitoring Networks for Water Suppliers

Science.gov (United States)

Bode, Felix; Loschko, Matthias; Nowak, Wolfgang

2015-04-01

Groundwater is a resource for drinking water and hence needs to be protected from contaminations. However, many well catchments include an inventory of known and unknown risk sources, which cannot be eliminated, especially in urban regions. As a matter of risk control, all these risk sources should be monitored. A one-to-one monitoring situation for each risk source would lead to a cost explosion and is even impossible for unknown risk sources. However, smart optimization concepts could help to find promising low-cost monitoring network designs. In this work we develop a concept to plan monitoring networks using multi-objective optimization. Our considered objectives are to maximize the probability of detecting all contaminations, to enhance the early warning time before detected contaminations reach the drinking water well, and to minimize the installation and operating costs of the monitoring network. Using multi-objectives optimization, we avoid the problem of having to weight these objectives to a single objective-function. These objectives are clearly competing, and it is impossible to know their mutual trade-offs beforehand - each catchment differs in many points and it is hardly possible to transfer knowledge between geological formations and risk inventories. To make our optimization results more specific to the type of risk inventory in different catchments we do risk prioritization of all known risk sources. Due to the lack of the required data, quantitative risk ranking is impossible. Instead, we use a qualitative risk ranking to prioritize the known risk sources for monitoring. Additionally, we allow for the existence of unknown risk sources that are totally uncertain in location and in their inherent risk. Therefore, they can neither be located nor ranked. Instead, we represent them by a virtual line of risk sources surrounding the production well. We classify risk sources into four different categories: severe, medium and tolerable for known risk

Intrusion detection and monitoring for wireless networks.

Energy Technology Data Exchange (ETDEWEB)

Thomas, Eric D.; Van Randwyk, Jamie A.; Lee, Erik J.; Stephano, Amanda (Indiana University); Tabriz, Parisa (University of Illinois at Urbana-Champaign); Pelon, Kristen (Cedarville University); McCoy, Damon (University of Colorado, Boulder); Lodato, Mark (Lafayette College); Hemingway, Franklin (University of New Mexico); Custer, Ryan P.; Averin, Dimitry (Polytechnic University); Franklin, Jason (Carnegie Mellon University); Kilman, Dominique Marie

2005-11-01

complete network coverage for use by emergency responders and other municipal agencies. In short, these Wi-Fi networks are being deployed everywhere. Much thought has been and is being put into evaluating cost-benefit analyses of wired vs. wireless networks and issues such as how to effectively cover an office building or municipality, how to efficiently manage a large network of wireless access points (APs), and how to save money by replacing an Internet service provider (ISP) with 802.11 technology. In comparison, very little thought and money are being focused on wireless security and monitoring for security purposes.

LANDMON a new integrated system for the management of landslide monitoring networks

Science.gov (United States)

Wrzesniak, Aleksandra; Giordan, Daniele; Allasia, Paolo

2017-04-01

Over the last decades, technological development has strongly increased the number of instruments that can be used to monitor landslide phenomena. Robotized Total Stations, GB-InSAR and GPS are only few examples of the devices that can be adapted to monitor the topographic changes due to mass movements. They are often organized in a complex network, aimed at controlling physical parameters related to the evolution of landslide activity. The level of complexity of these monitoring networks increases with the number of new available monitoring devices and this could generate a paradox: the source of data is so numerous and difficult to interpret that a full understanding of the phenomenon could be hampered. The Geohazard Monitoring Group (GMG) of Italian National Research Council (CNR) has a long experience in landslide monitoring. Over the years, GMG has developed a multidisciplinary approach for landslide management strategy called LANDMON (LANDslide MOnitoring Network). It is an automatic hybrid system focused not only on capturing and elaborating data from monitored site but also on web applications and on publishing bulletins aimed to disseminate monitoring results and to support decision makers. LANDMON is currently active in many landslide sites distributed in several areas in Italy and in Europe. LANDMON is derived from the previously developed systems like ADVICE (ADVanced dIsplaCement monitoring system for Early warning) and 3DA (three-dimensional Displacement Analysis). These systems are aimed to collect and to process monitoring dataset, to manage early warning application based on pre-defined thresholds, and to publish three-dimensional displacement maps in near real time. In addition, LANDMON integrates several new features, such as WebGIS application, modelling using inverse velocity method, and management of webcam monitoring system, meteorological parameters and borehole inclinometric data. Moreover, LANDMON is a communication strategy that focuses

Assessment of the water quality monitoring network of the Piabanha River experimental watersheds in Rio de Janeiro, Brazil, using autoassociative neural networks.

Science.gov (United States)

Villas-Boas, Mariana D; Olivera, Francisco; de Azevedo, Jose Paulo S

2017-09-01

Water quality monitoring is a complex issue that requires support tools in order to provide information for water resource management. Budget constraints as well as an inadequate water quality network design call for the development of evaluation tools to provide efficient water quality monitoring. For this purpose, a nonlinear principal component analysis (NLPCA) based on an autoassociative neural network was performed to assess the redundancy of the parameters and monitoring locations of the water quality network in the Piabanha River watershed. Oftentimes, a small number of variables contain the most relevant information, while the others add little or no interpretation to the variability of water quality. Principal component analysis (PCA) is widely used for this purpose. However, conventional PCA is not able to capture the nonlinearities of water quality data, while neural networks can represent those nonlinear relationships. The results presented in this work demonstrate that NLPCA performs better than PCA in the reconstruction of the water quality data of Piabanha watershed, explaining most of data variance. From the results of NLPCA, the most relevant water quality parameter is fecal coliforms (FCs) and the least relevant is chemical oxygen demand (COD). Regarding the monitoring locations, the most relevant is Poço Tarzan (PT) and the least is Parque Petrópolis (PP).

Monitoring nuclear reactor systems using neural networks and fuzzy logic

International Nuclear Information System (INIS)

Ikonomopoulos, A.; Tsoukalas, L.H.; Uhrig, R.E.; Mullens, J.A.

1992-01-01

A new approach is presented that demonstrates the potential of trained artificial neural networks (ANNs) as generators of membership functions for the purpose of monitoring nuclear reactor systems. ANN's provide a complex-to-simple mapping of reactor parameters in a process analogous to that of measurement. Through such virtual measurements the value of parameters with operational significance, e.g., control-valve-disk-position, valve-line-up-or performance can be determined. In the methodology presented the output of virtual measuring device is a set of membership functions which independently represent different states of the system. Utilizing a fuzzy logic representation offers the advantage of describing the state of the system in a condensed form, developed through linguistic descriptions and convenient for application in monitoring, diagnostics and generally control algorithms. The developed methodology is applied to the problem of measuring the disk position of the secondary flow control is clearly demonstrated as well as a method for selecting the actual output. The results suggest that it is possible to construct virtual measuring devices through artificial neural networks mapping dynamic time series to a set of membership functions and thus enhance the capability of monitoring systems

Treatability Study in Support of Intrinsic Remediation for the Jet Fuel Transfer Line Southwest of Building 412 and the POL Yard. Volume 1: Text. Wisconsin Air National Guard at Truax Field, Madison, Wisconsin

Science.gov (United States)

1997-01-01

Jamison et al., 1975; Atlas , 1981, 1984, 1988; Gibson an( ’)ramanian, 1984; Reinhard et al., 1984; Young, 1984; Bartha , 1986; Wilson , 1986, 1987...Academic Press, New York, 381 p. Atlas , R.M., 1981, Microbial degradation of petroleum hydrocarbons - an environmental 0 perspective: Microbiological Reviews...biodegradation: Microbial Ecology , vol. 12, p. 155-172. Bauman, B, 1991, Biodegradation Research of the American Petroleum Institute. Presented at: In

Nuclear power plant monitoring method by neural network and its application to actual nuclear reactor

International Nuclear Information System (INIS)

Nabeshima, Kunihiko; Suzuki, Katsuo; Shinohara, Yoshikuni; Tuerkcan, E.

1995-11-01

In this paper, the anomaly detection method for nuclear power plant monitoring and its program are described by using a neural network approach, which is based on the deviation between measured signals and output signals of neural network model. The neural network used in this study has three layered auto-associative network with 12 input/output, and backpropagation algorithm is adopted for learning. Furthermore, to obtain better dynamical model of the reactor plant, a new learning technique was developed in which the learning process of the present neural network is divided into initial and adaptive learning modes. The test results at the actual nuclear reactor shows that the neural network plant monitoring system is successfull in detecting in real-time the symptom of small anomaly over a wide power range including reactor start-up, shut-down and stationary operation. (author)

Scientific results - report 1981

International Nuclear Information System (INIS)

1982-01-01

During the year under report 1981, five working groups were active in the field of nuclear chemistry: neutron diffraction, radiation damage in solids, reactor chemistry, trace element research in bio-medicine and geo-chemistry. The objectives of the R+D projects ranged from the more basic research to the development of technological processes. Nuclear inspection methodes that have already been developed (e.g. neutron diffraction, trace element analysis) have increasingly been used in an interdisciplinary way. Besides these R+D projects the project of increase of power of the BER II was pursued also in 1981, and further planning documents on the extension of the BER II have been established. The report informs about the most important results of the single sections. A list of the publications (with abstracts) and lectures, also by guest scientists, is attached. (RB) [de

Event localization in underwater wireless sensor networks using Monitoring Courses

KAUST Repository

Debont, Matthew John Robert

2012-08-01

We propose m-courses (Monitoring Courses), a novel solution to localize events in an underwater wireless sensor network. These networks consists of surface gateways and relay nodes. GPS can localize the position of surface gateways which can then distribute their locations through the network using acoustic modems. Relay nodes are deployed to remain static, but these untethered nodes may drift due to water currents, resulting in disruption of communication links. We develop a novel underwater alarm system using a cyclic graph model. In the event of link failure, a series of alarm packets are broadcast in the network. These alarms are then captured by the underwater m-courses, which can also be used to assure network connectivity and identify node failures. M-courses also allow the network to localize events and identify network issues locally before forwarding results upwards to a Surface Gateway node. This reduces communication overhead and allows for efficient management of nodes in a mobile network. Our results show that m-course routing reduces the number of sends required to report an event to a Surface Gateway by up to 80% when compared to a naïve routing implementation.

Environmental radioactivity in Greenland in 1981

International Nuclear Information System (INIS)

Aarkrog, A.; Dahlgaard, H.; Hansen, H.; Lippert, J.; Nilsson, K.; Holm, E.

1982-07-01

Measurements of fallout radioactivity in Greenland in 1981 are reported. Strontium-90 (and Cesium-137 in most cases) was determined in samples of precipitation, sea water, vegetation, animals, and drinking water. Estimates are given of the mean contents of 90 Sr and 137 Cs in the human diet in Greenland in 1981. Further results of the 239 , 240 Pu and 241 Am measurements on samples from the expedition to Thule in August 1979 are prsented. Brown algae collected in East Greenland in 1969 were analysed for Pu and Am. (author)

State energy-price system: 1981 update

Energy Technology Data Exchange (ETDEWEB)

Fang, J.M.; Imhoff, K.L.; Hood, L.J.

1983-08-01

This report updates the State Energy Price Data System (STEPS) to include state-level energy prices by fuel and by end-use sectors for 1981. Both physical unit prices and Btu prices are presented. Basic documentation of the data base remains generally the same as in the original report: State Energy Price System; Volume 1: Overview and Technical Documentation (DOE/NBB-0029 Volume 1 of 2, November 1982). The present report documents only the changes in procedures necessitated by the update to 1981 and the corrections to the basic documentation.

Monitoring the Environmental Impact of TiO2 Nanoparticles Using a Plant-Based Sensor Network

Science.gov (United States)

Lenaghan, Scott C.; Li, Yuanyuan; Zhang, Hao; Burris, Jason N.; Stewart, C. Neal; Parker, Lynne E.; Zhang, Mingjun

2016-01-01

The increased manufacturing of nanoparticles for use in cosmetics, foods, and clothing necessitates the need for an effective system to monitor and evaluate the potential environmental impact of these nanoparticles. The goal of this research was to develop a plant-based sensor network for characterizing, monitoring, and understanding the environmental impact of TiO2 nanoparticles. The network consisted of potted Arabidopsis thaliana with a surrounding water supply, which was monitored by cameras attached to a laptop computer running a machine learning algorithm. Using the proposed plant sensor network, we were able to examine the toxicity of TiO2 nanoparticles in two systems: algae and terrestrial plants. Increased terrestrial plant growth was observed upon introduction of the nanoparticles, whereas algal growth decreased significantly. The proposed system can be further automated for high-throughput screening of nanoparticle toxicity in the environment at multiple trophic levels. The proposed plant-based sensor network could be used for more accurate characterization of the environmental impact of nanomaterials. PMID:28458617

Sludge application and monitoring program on the Oak Ridge Reservation, 1986--1993

Energy Technology Data Exchange (ETDEWEB)

Gunderson, C.A.; Larsen, I.L.; Boston, H.L.; Bradburn, D.M. [Oak Ridge National Lab., TN (United States); Van Miegroet, H. [Utah State Univ., Logan, UT (United States). Dept. of Forest Resources; Morris, J.L. [Jaycor, Inc., Oak Ridge, TN (United States); Walzer, A.E. [Lockheed Martin Energy Systems, Oak Ridge, TN (United States). Central Environmental Compliance; Adler, T.C. [Bechtel National, Inc., Oak Ridge, TN (United States); Huq, M. [Oak Ridge Associated Universities, TN (United States)

1995-09-01

Municipal sewage sludge has been applied to forests and pastures on the Oak Ridge Reservation since 1983 as a method of both disposal and beneficial reuse. Application was carried out under Tennessee permits issued to the city of Oak Ridge for land disposal of sewage sludge. In conjunction with these applications, information has been collected concerning sludge quantity and characteristics, soil parameters, soil water constituents, groundwater quality, surface runoff water quality, and various chemical constituents in vegetation on application sites. This information provides (1) a record of sludge application on the DOE reservations and (2) documentation of changes in soil parameters following sludge application. The information also provides a basis for evaluating the implications of the land application of municipal sewage sludge for soil and water quality and for evaluating the fate of sludge constituents when sludge is either sprayed or injected on pasture sites or surface applied in forested sites. This report covers in detail sludge applications conducted from 1986 through 1993, with some data from the period between 1983 and 1986. Anaerobically digested liquid sludge (2% to 4% solids) from the city of Oak Ridge had a relatively high nitrogen content (8% dry weight) and average to low concentrations of potentially problematic metals, compared with typical municipal sludges. Few potentially hazardous organic chemicals were detected in the sludge, and when found, these were at very low concentrations. Oak Ridge sludge is somewhat unique in that it contains radionuclides ({sup 137}Cs, {sup 60}Co, {sup 131}I, uranium isotopes, {sup 90}Sr, and occasionally {sup 99}Tc) at concentrations much higher than typical municipal sludges. Land application of sewage sludge can dilute or destroy problematic sludge constituents while improving soil fertility. Correct management has made these sludge applications a model of environmentally responsible waste management.

Development of nuclear power plant monitoring system with neutral network using on-line PWR plant simulator

International Nuclear Information System (INIS)

Nabeshima Kunihiko; Suzuki Katsuo; Nose, Shoichi; Kudo, Kazuhiko

1996-01-01

The purpose of this paper is to demonstrate a nuclear power plant monitoring system using artificial neural network (ANN). The major advantages of the monitoring system are that a multi-output process system can be modelled using measurement information without establishing any mathematical expressions. The dynamics model of reactor plant was constructed by using three layered auto-associative neural network with backpropagation learning algorithm. The basic idea of anomaly detection method is to monitor the deviation between process signals measured from actual plant and corresponding output signals from the ANN plant model. The simulator used is a self contained system designed for training. Four kinds of simulated malfunction caused by equipment failure during steady state operation were used to evaluate the capability of the neural network monitoring system. The results showed that this monitoring system detected the symptom of small anomaly earlier than the prevailing alarm system. (author). 7 refs, 7 figs, 2 tabs

Development of nuclear power plant monitoring system with neutral network using on-line PWR plant simulator

Energy Technology Data Exchange (ETDEWEB)

Kunihiko, Nabeshima; Katsuo, Suzuki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan); Nose, Shoichi; Kudo, Kazuhiko [Kyushu Univ., Fukuoka (Japan). Faculty of Engineering

1997-12-31

The purpose of this paper is to demonstrate a nuclear power plant monitoring system using artificial neural network (ANN). The major advantages of the monitoring system are that a multi-output process system can be modelled using measurement information without establishing any mathematical expressions. The dynamics model of reactor plant was constructed by using three layered auto-associative neural network with backpropagation learning algorithm. The basic idea of anomaly detection method is to monitor the deviation between process signals measured from actual plant and corresponding output signals from the ANN plant model. The simulator used is a self contained system designed for training. Four kinds of simulated malfunction caused by equipment failure during steady state operation were used to evaluate the capability of the neural network monitoring system. The results showed that this monitoring system detected the symptom of small anomaly earlier than the prevailing alarm system. (author). 7 refs, 7 figs, 2 tabs.

National Energy Balance - 1981

International Nuclear Information System (INIS)

Anon.

1981-01-01

The National Energy Balance - 1981, shows a new metodology and information in level of several economic sectors, as well as a separation of primary and secondary energy sources, its energy fluxes, i.e. production, imports, exports, consumption, etc...(E.G.) [pt

A Low-Cost, Real-Time Network for Radiological Monitoring Around Nuclear Facilities

International Nuclear Information System (INIS)

Bertoldo, N A

2004-01-01

A low-cost, real-time radiological sensor network for emergency response has been developed and deployed at the Lawrence Livermore National Laboratory (LLNL). The Real-Time Radiological Area Monitoring (RTRAM) network is comprised of 16 Geiger-Mueller (GM) sensors positioned on the site perimeter to continuously monitor radiological conditions as part of LLNL's comprehensive environment/safety/health protection program. The RTRAM network sensor locations coincide with wind sector directions to provide thorough coverage of the one square mile site. These low-power sensors transmit measurement data back to a central command center (CCC) computer through the LLNL telecommunications infrastructure. Alarm conditions are identified by comparing current data to predetermined threshold parameters and are validated by comparison with plausible dispersion modeling scenarios and prevailing meteorological conditions. Emergency response personnel are notified of alarm conditions by automatic radio- and computer- based notifications. A secure intranet provides emergency response personnel with current condition assessment data that enable them to direct field response efforts remotely. This system provides a low-cost real-time radiation monitoring solution that is easily converted to incorporate both a hard-wired interior perimeter with strategically positioned wireless secondary and tertiary concentric remote locations. These wireless stations would be configured with solar voltaic panels that provide current to recharge batteries and power the sensors and radio transceivers. These platforms would supply data transmission at a range of up to 95 km from a single transceiver location. As necessary, using radio transceivers in repeater mode can extend the transmission range. The RTRAM network as it is presently configured at LLNL has proven to be a reliable system since initial deployment in August 2001 and maintains stability during inclement weather conditions. With the proposed

Basalt waste isolation project. Quarterly report, April 1, 1981-June 30, 1981

Energy Technology Data Exchange (ETDEWEB)

Deju, R.A.

1981-08-01

This document reports progress made in the Basalt Waste Isolation Project during the third quarter of fiscal year 1981. Efforts are described for the following programs of the project work breakdown structure: systems; waste package; site; repository; regulatory and institutional; test facilities; in situ test facilities.

Using Wireless Sensor Networks to Achieve Intelligent Monitoring for High-Temperature Gas-Cooled Reactor

Directory of Open Access Journals (Sweden)

Jianghai Li

2017-01-01

Full Text Available High-temperature gas-cooled reactors (HTGR can incorporate wireless sensor network (WSN technology to improve safety and economic competitiveness. WSN has great potential in monitoring the equipment and processes within nuclear power plants (NPPs. This technology not only reduces the cost of regular monitoring but also enables intelligent monitoring. In intelligent monitoring, large sets of heterogeneous data collected by the WSN can be used to optimize the operation and maintenance of the HTGR. In this paper, WSN-based intelligent monitoring schemes that are specific for applications of HTGR are proposed. Three major concerns regarding wireless technology in HTGR are addressed: wireless devices interference, cybersecurity of wireless networks, and wireless standards selected for wireless platform. To process nonlinear and non-Gaussian data obtained by WSN for fault diagnosis, novel algorithms combining Kernel Entropy Component Analysis (KECA and support vector machine (SVM are developed.

Development Of A Sensor Network Test Bed For ISD Materials And Structural Condition Monitoring

International Nuclear Information System (INIS)

Zeigler, K.; Ferguson, B.; Karapatakis, D.; Herbst, C.; Stripling, C.

2011-01-01

The P Reactor at the Savannah River Site is one of the first reactor facilities in the US DOE complex that has been placed in its end state through in situ decommissioning (ISD). The ISD end state consists of a grout-filled concrete civil structure within the concrete frame of the original building. To evaluate the feasibility and utility of remote sensors to provide verification of ISD system conditions and performance characteristics, an ISD Sensor Network Test Bed has been designed and deployed at the Savannah River National Laboratory. The test bed addresses the DOE-EM Technology Need to develop a remote monitoring system to determine and verify ISD system performance. Commercial off-the-shelf sensors have been installed on concrete blocks taken from walls of the P Reactor Building. Deployment of this low-cost structural monitoring system provides hands-on experience with sensor networks. The initial sensor system consists of: (1) Groutable thermistors for temperature and moisture monitoring; (2) Strain gauges for crack growth monitoring; (3) Tiltmeters for settlement monitoring; and (4) A communication system for data collection. Preliminary baseline data and lessons learned from system design and installation and initial field testing will be utilized for future ISD sensor network development and deployment.

DEVELOPMENT OF A SENSOR NETWORK TEST BED FOR ISD MATERIALS AND STRUCUTRAL CONDITION MONITORING

Energy Technology Data Exchange (ETDEWEB)

Zeigler, K.; Ferguson, B.; Karapatakis, D.; Herbst, C.; Stripling, C.

2011-07-06

The P Reactor at the Savannah River Site is one of the first reactor facilities in the US DOE complex that has been placed in its end state through in situ decommissioning (ISD). The ISD end state consists of a grout-filled concrete civil structure within the concrete frame of the original building. To evaluate the feasibility and utility of remote sensors to provide verification of ISD system conditions and performance characteristics, an ISD Sensor Network Test Bed has been designed and deployed at the Savannah River National Laboratory. The test bed addresses the DOE-EM Technology Need to develop a remote monitoring system to determine and verify ISD system performance. Commercial off-the-shelf sensors have been installed on concrete blocks taken from walls of the P Reactor Building. Deployment of this low-cost structural monitoring system provides hands-on experience with sensor networks. The initial sensor system consists of: (1) Groutable thermistors for temperature and moisture monitoring; (2) Strain gauges for crack growth monitoring; (3) Tiltmeters for settlement monitoring; and (4) A communication system for data collection. Preliminary baseline data and lessons learned from system design and installation and initial field testing will be utilized for future ISD sensor network development and deployment.

The use of hierarchical clustering for the design of optimized monitoring networks

Science.gov (United States)

Soares, Joana; Makar, Paul Andrew; Aklilu, Yayne; Akingunola, Ayodeji

2018-05-01

Associativity analysis is a powerful tool to deal with large-scale datasets by clustering the data on the basis of (dis)similarity and can be used to assess the efficacy and design of air quality monitoring networks. We describe here our use of Kolmogorov-Zurbenko filtering and hierarchical clustering of NO2 and SO2 passive and continuous monitoring data to analyse and optimize air quality networks for these species in the province of Alberta, Canada. The methodology applied in this study assesses dissimilarity between monitoring station time series based on two metrics: 1 - R, R being the Pearson correlation coefficient, and the Euclidean distance; we find that both should be used in evaluating monitoring site similarity. We have combined the analytic power of hierarchical clustering with the spatial information provided by deterministic air quality model results, using the gridded time series of model output as potential station locations, as a proxy for assessing monitoring network design and for network optimization. We demonstrate that clustering results depend on the air contaminant analysed, reflecting the difference in the respective emission sources of SO2 and NO2 in the region under study. Our work shows that much of the signal identifying the sources of NO2 and SO2 emissions resides in shorter timescales (hourly to daily) due to short-term variation of concentrations and that longer-term averages in data collection may lose the information needed to identify local sources. However, the methodology identifies stations mainly influenced by seasonality, if larger timescales (weekly to monthly) are considered. We have performed the first dissimilarity analysis based on gridded air quality model output and have shown that the methodology is capable of generating maps of subregions within which a single station will represent the entire subregion, to a given level of dissimilarity. We have also shown that our approach is capable of identifying different

Multi-detector environmental radiation monitor with multichannel data communication for Indian Environmental Radiation Monitoring Network (IERMON)