WorldWideScience

Sample records for monitor power system

  1. Power Transformer Intelligence Monitor System

    Institute of Scientific and Technical Information of China (English)

    Sun Jianshe; Shi Lei

    2006-01-01

    An auto-monitoring system has been created that could monitor the main parameter of power transformers. It reads data of V&I by precision rectifier circuit and amplifier, and converted electric energy into pulse signal by means of sensor technique and pulse converter circuit, it is sent into microcomputer to process, completed monitoring to power transformer parameters and running state by software system. It can register all kinds of key data, and provide all kinds of virtual technical data for managing sections and can auto-form all kinds of electric annual reports and monthly reports analysis graphs such as managing graphs. It notably improves the safety and reliability of transformer, with strong anti-jamming technique and unique function, it can be used on the transformers in railway' s self-closing lines and all kinds of transformer stations.

  2. Automatic calorimetry system monitors RF power

    Science.gov (United States)

    Harness, B. W.; Heiberger, E. C.

    1969-01-01

    Calorimetry system monitors the average power dissipated in a high power RF transmitter. Sensors measure the change in temperature and the flow rate of the coolant, while a multiplier computes the power dissipated in the RF load.

  3. Solar Power Systems Web Monitoring

    CERN Document Server

    Kumar, Bimal Aklesh

    2011-01-01

    All over the world the peak demand load is increasing and the load factor is decreasing year-by-year. The fossil fuel is considered insufficient thus solar energy systems are becoming more and more useful, not only in terms of installation but monitoring of these systems is very crucial. Monitoring becomes very important when there are a large number of solar panels. Monitoring would allow early detection if the output falls below required level or one of the solar panel out of 1000 goes down. In this study the target is to monitor and control a developed solar panel by using available internet foundation. This web-enabled software will provide more flexibility over the system such as transmitting data from panel to the host computer and disseminating information to relevant stake holders barring any geographical barrier. The software would be built around web server with dynamic HTML and JAVA, this paper presents the preliminary design of the proposed system.

  4. A novel electric power quality monitoring system for transient analysis

    OpenAIRE

    2014-01-01

    Electricity is vital for our daily life in modern cites. In order to ensure its reliability and supply, an electric power monitoring system is indispensable in an electric power system. Currently, most electric power monitoring systems are designed for steady-state monitoring only. They may not be able to monitor instantaneous power disturbances, such as voltage surge, happened in electric power systems. In fact, instantaneous power disturbances are frequently found in electric power systems,...

  5. Computer system for monitoring power boiler operation

    Energy Technology Data Exchange (ETDEWEB)

    Taler, J.; Weglowski, B.; Zima, W.; Duda, P.; Gradziel, S.; Sobota, T.; Cebula, A.; Taler, D. [Cracow University of Technology, Krakow (Poland). Inst. for Process & Power Engineering

    2008-02-15

    The computer-based boiler performance monitoring system was developed to perform thermal-hydraulic computations of the boiler working parameters in an on-line mode. Measurements of temperatures, heat flux, pressures, mass flowrates, and gas analysis data were used to perform the heat transfer analysis in the evaporator, furnace, and convection pass. A new construction technique of heat flux tubes for determining heat flux absorbed by membrane water-walls is also presented. The current paper presents the results of heat flux measurement in coal-fired steam boilers. During changes of the boiler load, the necessary natural water circulation cannot be exceeded. A rapid increase of pressure may cause fading of the boiling process in water-wall tubes, whereas a rapid decrease of pressure leads to water boiling in all elements of the boiler's evaporator - water-wall tubes and downcomers. Both cases can cause flow stagnation in the water circulation leading to pipe cracking. Two flowmeters were assembled on central downcomers, and an investigation of natural water circulation in an OP-210 boiler was carried out. On the basis of these measurements, the maximum rates of pressure change in the boiler evaporator were determined. The on-line computation of the conditions in the combustion chamber allows for real-time determination of the heat flowrate transferred to the power boiler evaporator. Furthermore, with a quantitative indication of surface cleanliness, selective sootblowing can be directed at specific problem areas. A boiler monitoring system is also incorporated to provide details of changes in boiler efficiency and operating conditions following sootblowing, so that the effects of a particular sootblowing sequence can be analysed and optimized at a later stage.

  6. Power system monitoring and source control of the Space Station Freedom DC power system testbed

    Science.gov (United States)

    Kimnach, Greg L.; Baez, Anastacio N.

    1992-01-01

    Unlike a terrestrial electric utility which can purchase power from a neighboring utility, the Space Station Freedom (SSF) has strictly limited energy resources; as a result, source control, system monitoring, system protection, and load management are essential to the safe and efficient operation of the SSF Electric Power System (EPS). These functions are being evaluated in the DC Power Management and Distribution (PMAD) Testbed which NASA LeRC has developed at the Power System Facility (PSF) located in Cleveland, Ohio. The testbed is an ideal platform to develop, integrate, and verify power system monitoring and control algorithms. State Estimation (SE) is a monitoring tool used extensively in terrestrial electric utilities to ensure safe power system operation. It uses redundant system information to calculate the actual state of the EPS, to isolate faulty sensors, to determine source operating points, to verify faults detected by subsidiary controllers, and to identify high impedance faults. Source control and monitoring safeguard the power generation and storage subsystems and ensure that the power system operates within safe limits while satisfying user demands with minimal interruptions. System monitoring functions, in coordination with hardware implemented schemes, provide for a complete fault protection system. The objective of this paper is to overview the development and integration of the state estimator and the source control algorithms.

  7. Wide-area monitoring of interconnected power systems

    CERN Document Server

    Messina, Arturo Román

    2015-01-01

    This book provides a compact yet comprehensive treatment of advanced data-driven signal processing techniques for the analysis and characterization of both ambient power system data and transient oscillations resulting from major disturbances. Inspired by recent developments in multi-sensor data fusion, multi-temporal data assimilation techniques for power system monitoring are proposed and tested in the context of modern wide-area monitoring system architectures. Recent advances in understanding and modeling nonlinear, time-varying power system processes are reviewed and factors affecting the

  8. MiSmart - Power quality and monitoring system

    OpenAIRE

    PAHULJE, JAN

    2014-01-01

    In this thesis we describe an application for collecting and analyzing power quality data of electric distribution systems. The thesis is divided into three parts. We begin with a theoretical description of electric distribution networks and define power quality. We then describe the basics of quality monitoring systems and measuring devices, which are used to measure power quality in electric distribution network. The main contribution of this thesis is an implementation of MiSmart, a web pl...

  9. MiSmart - Power quality and monitoring system

    OpenAIRE

    Pahulje, Jan

    2014-01-01

    In this thesis we describe an application for collecting and analyzing power quality data of electric distribution systems. The thesis is divided into three parts. We begin with a theoretical description of electric distribution networks and define power quality. We then describe the basics of quality monitoring systems and measuring devices, which are used to measure power quality in electric distribution network. The main contribution of this thesis is an implementation of MiSmart, a web pl...

  10. An optically remote powered subsea video monitoring system

    Science.gov (United States)

    Lau, Fat Kit; Stewart, Brian; McStay, Danny

    2012-06-01

    The drive for Ocean pollution prevention requires a significant increase in the extent and type of monitoring of subsea hydrocarbon production equipment. Sensors, instrumentation, control electronics, data logging and transmission units comprising such monitoring systems will all require to be powered. Conventionally electrical powering is supplied by standard subsea electrical cabling. The ability to visualise the assets being monitored and any changes or faults in the equipment is advantageous to an overall monitoring system. However the effective use of video cameras, particularly if the transmission of real time high resolution video is desired, requires a high data rate and low loss communication capability. This can be challenging for heavy and costly electrical cables over extended distances. For this reason optical fibre is often adopted as the communication channel. Using optical fibre cables for both communications and power delivery can also reduce the cost of cabling. In this paper we report a prototype optically remote powered subsea video monitoring system that provides an alternative approach to powering subsea video cameras. The source power is transmitted to the subsea module through optical fibre with an optical-to-electrical converter located in the module. To facilitate intelligent power management in the subsea module, a supercapacitor based intermediate energy storage is installed. Feasibility of the system will be demonstrated. This will include energy charging and camera operation times.

  11. Monitoring and analyzing features of electrical power quality system performance

    Directory of Open Access Journals (Sweden)

    Genci Sharko

    2010-06-01

    Full Text Available Power quality is a set of boundaries that allows electrical systems to function in their intended manner without significant loss of performance or life. The term is used to describe electric power that drives an electrical load and the load's ability to function properly with that electric power. Without the proper quality of the power, an electrical device may malfunction, fail prematurely or not operate at all. There are many reasons why the electric power can be of poor quality and many more causes of such poor quality power. Power quality of power systems, which affects all connected electrical and electronic equipment, is a measure of deviations in voltages, currents, frequency, temperatures, winding forces and torques of particular supply systems and their components. In recent years, a considerable increase in nonlinear loads has been experienced; in particular distributed loads, such as computers, monitors and lighting, and distributed sources. The aim of this paper is to display a way of monitoring and analyzing features of electrical power quality system. As a monitoring example is taken output from power transformer rated at 320 kVA, part of distribution grid of Durres City in Albania.

  12. Development of on-line laser power monitoring system

    Science.gov (United States)

    Ding, Chien-Fang; Lee, Meng-Shiou; Li, Kuan-Ming

    2016-03-01

    Since the laser was invented, laser has been applied in many fields such as material processing, communication, measurement, biomedical engineering, defense industries and etc. Laser power is an important parameter in laser material processing, i.e. laser cutting, and laser drilling. However, the laser power is easily affected by the environment temperature, we tend to monitor the laser power status, ensuring there is an effective material processing. Besides, the response time of current laser power meters is too long, they cannot measure laser power accurately in a short time. To be more precisely, we can know the status of laser power and help us to achieve an effective material processing at the same time. To monitor the laser power, this study utilize a CMOS (Complementary metal-oxide-semiconductor) camera to develop an on-line laser power monitoring system. The CMOS camera captures images of incident laser beam after it is split and attenuated by beam splitter and neutral density filter. By comparing the average brightness of the beam spots and measurement results from laser power meter, laser power can be estimated. Under continuous measuring mode, the average measuring error is about 3%, and the response time is at least 3.6 second shorter than thermopile power meters; under trigger measuring mode which enables the CMOS camera to synchronize with intermittent laser output, the average measuring error is less than 3%, and the shortest response time is 20 millisecond.

  13. A Remote Real-Time Monitoring System for Power Quality

    Institute of Scientific and Technical Information of China (English)

    黄治清; 贺建闽

    2003-01-01

    An introduction is made to the composition, design method and engineering application of a remote real-time monitoring system of power quality in substations based on internet. With virtual instrument and network technique adopted, this system is characterized by good real-time property, high reliability, plentiful functions, and so on. It also can be used to monitor the load of a substation, such as electric locomotives.

  14. Wide Area Measurement Based Security Assessment & Monitoring of Modern Power System: A Danish Power System Case Study

    DEFF Research Database (Denmark)

    Rather, Zakir Hussain; Chen, Zhe; Thøgersen, Paul

    2013-01-01

    Power System security has become a major concern across the global power system community. This paper presents wide area measurement system (WAMS) based security assessment and monitoring of modern power system. A new three dimensional security index (TDSI) has been proposed for online security...... monitoring of modern power system with large scale renewable energy penetration. Phasor measurement unit (PMU) based WAMS has been implemented in western Danish Power System to realize online security monitoring and assessment in power system control center. The proposed security monitoring system has been...

  15. INFORMATION SYSTEMS AND PROCESSES OF MONITORING POWER TRANSFORMERS CONDITION

    Directory of Open Access Journals (Sweden)

    Litvinov V. N.

    2016-02-01

    Full Text Available To solve the problem of reducing the power supply system’s reliability a prompt full-scale diagnostics based on modern methods can help. Inculcation of information systems for the operational diagnostics implementation allows providing the operating personnel with information that enables to predict possible infringements in power transformers work and to prepare in advance an action plan to address them. The paper presents fragments of the developed monitoring system of power transformer using programmable logic controllers. Within the work of the system there were marked such groups of controlled parameters as information about temperature and the cooling system work; magnitude of windings voltage per phase; the windings current values per phase; information about being transmitted and transmitted power; information about the insulation state. There is designed a functional scheme of the system for monitoring the state of the power transformer. There is described a general algorithm of system functioning. There is developed graphical operator interface that allows to monitor the object state and to manage the system state. Using XML markup language there was designed format of data packets. Designed hardware and software package can be used in the educational process, as it allows to improve the quality of students training, to bring them closer to the realities of modern professional activities; in operational activities as complying with the approved domestic calculating methods replacement of foreign software; in science in solving problems of analysis and optimization of operating parameters of power transformers

  16. An Integrated Health Monitoring System for Fission Surface Power

    Science.gov (United States)

    Hashemian, H. M.; Shumaker, B. D.; McCulley, J. R.; Morton, G. W.

    Based on such criteria as safety and mission success, programmatic risk, affordability, and extensibility/flexibility, the National Aeronautics and Space Administration (NASA) has chosen fission surface power (FSP) as the primary energy source for building a sustained human presence on the Moon, exploring Mars, and extremely long-duration space missions. The current benchmark FSP system has a mission life of at least 8 years during which time there is no opportunity for repair, sensor calibrations, or periodic maintenance tasks that are normally performed on terrestrial-based nuclear power plants during scheduled outages. Current technology relies heavily on real-time human interaction, monitoring and control. However; due to the long communication times between the Earth and Moon, or Mars, real-time human control is not possible, resulting in a critical need to develop autonomous health monitoring technology for FSP systems.This paper describes the design and development of an autonomous health monitoring system that will (1) provide on-line calibration monitoring, (2) reduce uncertainties in sensor measurements, and (3) provide sensor validation and fault detection capabilities for the control systems of various FSP subsystems. The health monitoring system design integrates a number of signal processing algorithms and techniques such as cross-calibration, empirical modeling using neural networks, and physical modeling under a modular signal processing platform that will enable robust sensor and system monitoring without the need for human interaction. Prototypes of the health monitoring system have been tested and validated on data acquired from preliminary subsystem testing of NASA's FSP Technology Demonstration Unit (TDU) as well as simulated laboratory data. Results from this testing have demonstrated the utility and benefits that such autonomous health monitoring systems can provide to FSP subsystems and other potential applications within NASA such as launch

  17. Application of the thermoelectric MEMS microwave power sensor in a power radiation monitoring system

    Science.gov (United States)

    Bo, Gao; Jing, Yang; Si, Jiang; Debo, Wang

    2016-08-01

    A power radiation monitoring system based on thermoelectric MEMS microwave power sensors is studied. This monitoring system consists of three modules: a data acquisition module, a data processing and display module, and a data sharing module. It can detect the power radiation in the environment and the date information can be processed and shared. The measured results show that the thermoelectric MEMS microwave power sensor and the power radiation monitoring system both have a relatively good linearity. The sensitivity of the thermoelectric MEMS microwave power sensor is about 0.101 mV/mW, and the sensitivity of the monitoring system is about 0.038 V/mW. The voltage gain of the monitoring system is about 380 times, which is relatively consistent with the theoretical value. In addition, the low-frequency and low-power module in the monitoring system is adopted in order to reduce the electromagnetic pollution and the power consumption, and this work will extend the application of the thermoelectric MEMS microwave power sensor in more areas. Project supported by the National Natural Science Foundation of China (No. 11304158), the Province Natural Science Foundation of Jiangsu (No. BK20140890), the Open Research Fund of the Key Laboratory of MEMS of Ministry of Education, Southeast University (No. 3206005302), and the Scientific Research Foundation of Nanjing University of Posts and Telecommunications (Nos. NY213024, NY215139).

  18. Development of Core Monitoring System for Nuclear Power Plants (I)

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.H.; Kim, Y.B.; Park, M.G; Lee, E.K.; Shin, H.C.; Lee, D.J. [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

    1997-12-31

    1.Object and Necessity of the Study -The main objectives of this study are (1)conversion of APOLLO version BEACON system to HP-UX version core monitoring system, (2)provision of the technical bases to enhance the in-house capability of developing more advanced core monitoring system. 2.Results of the Study - In this study, the revolutionary core monitoring technologies such as; nodal analysis and isotope depletion calculation method, advanced schemes for power distribution control, and treatment of nuclear databank were established. The verification and validation work has been successfully performed by comparing the results with those of the design code and measurement data. The advanced graphic user interface and plant interface method have been implemented to ensure the future upgrade capability. The Unix shell scripts and system dependent software are also improved to support administrative functions of the system. (author). 14 refs., 112 figs., 52 tabs.

  19. Integrated online condition monitoring system for nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Hashemian, Hashem M. [Analysis and Measurement Services Corporation, Knoxville, TN (United States). AMS Technology Center

    2010-09-15

    Online condition monitoring or online monitoring (OLM) uses data acquired while a nuclear power is operating to continuously assess the health of the plant's sensors, processes, and equipment; to measure the dynamic performance of the plant's process instrumentation; to verify in-situ the calibration of the process instrumentation; to detect blockages, voids, and leaks in the pressure sensing lines; to identify core flow anomalies; to extend the life of neutron detectors and other sensors; and to measure the vibration of reactor internals. Both the steady-state or DC output of plant sensors and their AC signal or noise output can be used to assess sensor health, depending on whether the application is monitoring a rapidly changing (e.g., core barrel motion) or a slowly changing (e.g., sensor calibration) process. The author has designed, developed, installed, and tested OLM systems (comprised of software/hardware-based data acquisition and data processing modules) that integrate low-frequency (1 mHz to 1 Hz) techniques such as RTD cross-calibration, pressure transmitter calibration monitoring, and equipment condition monitoring and high-frequency (1 Hz to 1 kHz) techniques such as the noise analysis technique. The author has demonstrated the noise analysis technique's effectiveness for measuring the dynamic response-time of pressure transmitters and their sensing lines; for performing predictive maintenance on reactor internals; for detecting core flow anomalies; and for extending neutron detector life. Integrated online condition monitoring systems can combine AC and DC data acquisition and signal processing techniques, can use data from existing process sensors during all modes of plant operation, including startup, normal operation, and shutdown; can be retrofitted into existing PWRs, BWRs, and other reactor types and will be integrated into next-generation plants. (orig.)

  20. Solar powered wrist worn acquisition system for continuous photoplethysmogram monitoring.

    Science.gov (United States)

    Dieffenderfer, James P; Beppler, Eric; Novak, Tristan; Whitmire, Eric; Jayakumar, Rochana; Randall, Clive; Qu, Weiguo; Rajagopalan, Ramakrishnan; Bozkurt, Alper

    2014-01-01

    We present a solar-powered, wireless, wrist-worn platform for continuous monitoring of physiological and environmental parameters during the activities of daily life. In this study, we demonstrate the capability to produce photoplethysmogram (PPG) signals using this platform. To adhere to a low power budget for solar-powering, a 574 nm green light source is used where the PPG from the radial artery would be obtained with minimal signal conditioning. The system incorporates two monocrystalline solar cells to charge the onboard 20 mAh lithium polymer battery. Bluetooth Low Energy (BLE) is used to tether the device to a smartphone that makes the phone an access point to a dedicated server for long term continuous storage of data. Two power management schemes have been proposed depending on the availability of solar energy. In low light situations, if the battery is low, the device obtains a 5-second PPG waveform every minute to consume an average power of 0.57 mW. In scenarios where the battery is at a sustainable voltage, the device is set to enter its normal 30 Hz acquisition mode, consuming around 13.7 mW. We also present our efforts towards improving the charge storage capacity of our on-board super-capacitor.

  1. Long distance high power optical laser fiber break detection and continuity monitoring systems and methods

    Energy Technology Data Exchange (ETDEWEB)

    Rinzler, Charles C.; Gray, William C.; Faircloth, Brian O.; Zediker, Mark S.

    2016-02-23

    A monitoring and detection system for use on high power laser systems, long distance high power laser systems and tools for performing high power laser operations. In particular, the monitoring and detection systems provide break detection and continuity protection for performing high power laser operations on, and in, remote and difficult to access locations.

  2. Long distance high power optical laser fiber break detection and continuity monitoring systems and methods

    Energy Technology Data Exchange (ETDEWEB)

    Rinzler, Charles C.; Gray, William C.; Faircloth, Brian O.; Zediker, Mark S.

    2016-02-23

    A monitoring and detection system for use on high power laser systems, long distance high power laser systems and tools for performing high power laser operations. In particular, the monitoring and detection systems provide break detection and continuity protection for performing high power laser operations on, and in, remote and difficult to access locations.

  3. Autonomous Monitoring Aerial Robot System for Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ji H.; Gu, Beom W; Thai, Van X.; Rim, C. T. [KAIST, Daejeon (Korea, Republic of)

    2016-05-15

    In this paper, autonomous monitoring aerial robot system (AMARS), which includes omnidirectional wireless charging platform, aerial robot, landing coils and a battery management board, is proposed to guarantee automatic monitoring of NPPs. The prototype of the system is fabricated, and omnidirectional charging of the system is experimentally validated with 1 C charging state. AR(Aerial Robots)s are essential for NPP accident management because human cannot access to the accident site due to the risks of unexpected explosions, collapses, and high level of radioactive contaminants. Moreover, ARs can support operators to manage normal operation of NPPs built in harsh environment of high temperature and humidity such as UAE Barakah NPP. Because these ARs usually have very low energy capacity, however, the operation time of ARs is less than 30 minutes and should be recharged regularly by human powers, which makes it impossible to monitor NPPs by ARs automatically. In this paper, the concept of AMARS has been proposed and its performance was successfully verified with a fabricated prototype. The charging state of the on board battery in AR was measured as 0.5 C with the induced voltage of 18.6 V, which is well matched to the designed induced voltage when the AR was placed on the edge of the wireless charging platform.

  4. International Remote Monitoring Project Embalse Nuclear Power Station, Argentina Embalse Remote Monitoring System

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, Sigfried L.; Glidewell, Donnie D.; Bonino, Anibal; Bosler, Gene; Mercer, David; Maxey, Curt; Vones, Jaromir; Martelle, Guy; Busse, James; Kadner, Steve; White, Mike; Rovere, Luis

    1999-07-21

    The Autoridad Regulatoria Nuclear of Argentina (ARN), the International Atomic Energy Agency (IAEA), ABACC, the US Department of Energy, and the US Support Program POTAS, cooperated in the development of a Remote Monitoring System for nuclear nonproliferation efforts. This system was installed at the Embalse Nuclear Power Station last year to evaluate the feasibility of using radiation sensors in monitoring the transfer of spent fuel from the spent fuel pond to dry storage. The key element in this process is to maintain continuity of knowledge throughout the entire transfer process. This project evaluated the fundamental design and implementation of the Remote Monitoring System in its application to regional and international safeguard efficiency. New technology has been developed to enhance the design of the system to include storage capability on board sensor platforms. This evaluation has led to design enhancements that will assure that no data loss will occur during loss of RF transmission of the sensors.

  5. Grid Monitoring and Advanced Control of Distributed Power Generation Systems

    OpenAIRE

    Timbus, Adrian Vasile

    2007-01-01

    The movement towards a clean technology for energy production and the constraints in reducing the CO2 emissions are some factors facilitating the growth of distributed power generation systems based on renewable energy resources. Consequently, large penetration of distributed generators has been reported in some countries creating concerns about power system stability. This leads to a continuous evolution of grid interconnection requirements towards a better controllability of generated power...

  6. Autonomus I&C Maintenance and Health Monitoring System for Fission Surface Power Project

    Data.gov (United States)

    National Aeronautics and Space Administration — There currently exists no end-to-end reactor/power conversion monitoring system that can provide both autonomous health monitoring, but also in-situ sensor...

  7. Frequency Monitoring and Control during Power System Restoration Based on Wide Area Measurement System

    Directory of Open Access Journals (Sweden)

    Saber Nourizadeh

    2011-01-01

    Full Text Available Frequency control during power system restoration has not been strongly addressed. Operators are often concerned with the offline sizing of load and generation steps, but, nowadays, the introduction of Wide Area Measurement System (WAMS makes it possible to monitor the stability of power system online. The constraints of WAMS operation result in some changes in power system frequency control. This paper proposes a novel methodology for frequency control and monitoring during the early steps of power system restoration based on WAMS. Detailed load modeling is achieved based on the static load modeling approach. Power generators' modeling is also accomplished utilizing the single machine equivalent of the power system based on PMU measurements. Simulation results of the presented methodology on the 39 bus New England power system clearly show the effectiveness and applicability of the proposed method. The simulation results show that the presented approach has a completely acceptable precision and an outstanding speed with less than 0.05% error. The outstanding speed of the presented approach along with the result precision will result in a great promotion in power system restoration methodologies.

  8. A development of ITV system for power transmission line monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Hong Keun; Kim, Seok Ku; Lee, Kwang Joong; Lee, Won Bin [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center

    1995-12-31

    Transmission lines which are important to supply the electricity installed on the terrestrially severe site such as mountains needed to be monitored to prevent electric fault by snow accelerating, icing, tree contact, fire etc. Inspections by human patrol has been done but it seems not so efficient and satisfiable. To cope with this a transmission line monitoring system using industrial television and OPGW was developed and field trilled at the site. This paper describes about the optical video transceiver, video distributor and control devices (author).

  9. Industrial power monitoring and control : Power management system helps plant reduce energy demand

    Energy Technology Data Exchange (ETDEWEB)

    Crossley, L.E. [E2MS Inc., Whitby, ON (Canada); Demysh, M. [Diversa Cast Technologies, Guelph, ON (Canada)

    2001-05-01

    A power management system, consisting of a real time demand management system designed to allow managers to reduce operating costs via the automatic control of plant furnace loads with interference to production kept to a minimum, was installed at Diversa Cast Technologies in Guelph, Ontario. Diversa Cast Technologies manufactures aluminium, gray and ductile iron automotive lost foam castings. The potential load at the plant is approximately 5000 kW, and comprises two coreless induction melters and supporting equipment. Used for iron batch melting in the off peak hours between 2300 hours and 0700 hours, the first melter is rated at 2750 kW with 8000 lbs capacity. The aluminium heal melting during the on peak hours is handled by the second melter rated at 1250 kW with a 2700 lbs capacity. The electric utility operates on a time-of-use basis which includes penalties for on-peak demand. The installation of the system is described, along with its operation. The software comprises a number of modules to control all the necessary functions associated with data acquisition and analysis. The modules include: communications module, display module, analysis module, report module, database filer, and a system and cost configuration module. Commissioned in February 2000, the system has operated for approximately two months. After the initial period of two weeks where the system was in a monitoring mode to determine the baseline of energy demand and consumption, the demand control was activated. The numerous advantages of the system include better efficiency in the way energy is used, a reduction in the power factor penalties, power factor savings. The payback for this system is less than 8 months. The overall demand was lowered, the productivity improved along with the energy consumption efficiency. 4 figs.

  10. Design of Nuclear Power Plant Online Monitoring System

    Energy Technology Data Exchange (ETDEWEB)

    An, Sang-ha; Jeong, Yong-hoon; Chang, Soon-heung [KAIST, Daejeon (Korea, Republic of); Lee, Song-kyu [Korea Power Engineering Co., Yongin (Korea, Republic of)

    2007-07-01

    Statistical Quality Control techniques have been applied to many aspects of industrial engineering. An application to nuclear power plant maintenance and control is also presented that can greatly improve plant safety. As a demonstration of such an approach, a specific system is analyzed: the reactor coolant pumps (RCPs) and the fouling resistance of heat exchanger. This research uses Shewart X-bar, R charts, Cumulative Sum charts (CUSUM), and Sequential Probability Ratio Test (SPRT) to analyze the process for the state of statistical control. And the Control Chart Analyzer (CCA) has been made to support these analyses that can make a decision of error in process. The analysis shows that statistical process control methods can be applied as an early warning system capable of identifying significant equipment problems well in advance of traditional control room alarm indicators. Such a system would provide operators with enough time to respond to possible emergency situations and thus improve plant safety and reliability.

  11. Automatic and Intelligent Power Quality Disturbances Monitoring Based on Multi-Agent Systems

    Directory of Open Access Journals (Sweden)

    M. Hajian

    2012-09-01

    Full Text Available Power quality monitoring is the first step in the identification of power quality disturbances and reducing them in order to improve the performance of the power system. The aim of this paper is to propose the architecture of a new intelligent strategy for online and offline power quality monitoring system based on multi-agent systems. In this study, a multi-agent system for solving some problems in power quality monitoring, including computational complexity, low accuracy, change in the data pattern, non adaptive structure of detection system to changing conditions is proposed. In the proposed strategy, the agent characteristics, such as automatic and dynamic performance, intelligent, learning, reasoning ability, objectively and interoperability of agents are used. This paper is presented in two stages. In the one stage, to indicate problems in power quality monitoring, different methods of feature extraction, feature selection and classification for automatic recognition of power quality disturbances have been analyzed. Optimal selection of input feature vector of distinguish system is applied using different methods of data mining. Also, three well-known classifiers are considered. In another stage of the paper, to solve some challenges, the design of investigated structures in the form of a multi-agent system is expressed. The results of the experiments in this paper demonstrate the superiority of agents and multi-agent systems for online and offline power quality monitoring.

  12. On-Line Partial Discharge Monitoring and Diagnostic System for Power Transformer

    Institute of Scientific and Technical Information of China (English)

    LIN Du; JIANG Lei; LI Fuqi; ZHU Deheng; TAN Kexiong; WU Chengqi; JIN Xianhe; WANG Changchang; CHENG T. C.

    2005-01-01

    This paper introduces a computerized on-line partial discharge (PD) monitoring and diagnostic system for transformers. The system, which is already in use in a power station, uses wide-band active transducers and a data acquisition unit with modularized and exchangeable components. The system software is a power equipment monitoring and diagnostic system, which is based on the component object model, and was developed for monitoring multiple parameters in multiple power supply systems. The statistical characteristics of PDs in power transformers were studied using 7 experimental models for simulating PDs in transformers and 3 models for simulating interfering discharges in air. The discharge features were analyzed using a 3-D pattern chart with a three-layer back-propagation artificial neural network used to recognize the patterns. The results show that PDs in air and oil can be distinguished. The model can be used for interference rejection on-line monitoring of partial discharge in transformers.

  13. A two-tiered self-powered wireless monitoring system architecture for bridge health management

    Science.gov (United States)

    Kurata, Masahiro; Lynch, Jerome P.; Galchev, Tzeno; Flynn, Michael; Hipley, Patrick; Jacob, Vince; van der Linden, Gwendolyn; Mortazawi, Amir; Najafi, Khalil; Peterson, Rebecca L.; Sheng, Li-Hong; Sylvester, Dennis; Thometz, Edward

    2010-04-01

    Bridges are an important societal resource used to carry vehicular traffic within a transportation network. As such, the economic impact of the failure of a bridge is high; the recent failure of the I-35W Bridge in Minnesota (2007) serves as a poignant example. Structural health monitoring (SHM) systems can be adopted to detect and quantify structural degradation and damage in an affordable and real-time manner. This paper presents a detailed overview of a multi-tiered architecture for the design of a low power wireless monitoring system for large and complex infrastructure systems. The monitoring system architecture employs two wireless sensor nodes, each with unique functional features and varying power demand. At the lowest tier of the system architecture is the ultra-low power Phoenix wireless sensor node whose design has been optimized to draw minimal power during standby. These ultra low-power nodes are configured to communicate their measurements to a more functionally-rich wireless sensor node residing on the second-tier of the monitoring system architecture. While the Narada wireless sensor node offers more memory, greater processing power and longer communication ranges, it also consumes more power during operation. Radio frequency (RF) and mechanical vibration power harvesting is integrated with the wireless sensor nodes to allow them to operate freely for long periods of time (e.g., years). Elements of the proposed two-tiered monitoring system architecture are validated upon an operational long-span suspension bridge.

  14. Autonomus I&C Maintenance and Health Monitoring System for Fission Surface Power Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The primary goal of this project is to design and develop an autonomous instrumentation and control (I&C) health monitoring system for space nuclear power...

  15. ZigBee Based Industrial Automation Profile for Power Monitoring Systems

    OpenAIRE

    Archana R. Raut,; Dr. L. G. Malik

    2011-01-01

    Industrial automations which are mostly depend upon the power systems & which requires distance controlled and regulated systems. Mostly voltage and current equipped parameters along with power and energy management system forms the industrial scenario for automations. Wireless technology which meets to cost, speed and distance scenario will always be a point of an interest for research. In this research work we mainly monitored power related parameters and enable remote switching devices for...

  16. WAMS-based monitoring and control of Hopf bifurcations in multi-machine power systems

    Institute of Scientific and Technical Information of China (English)

    Shao-bu WANG; Quan-yuan JIANG; Yi-jia CAO

    2008-01-01

    A method is proposed to monitor and control Hopf bifurcations in multi-machine power systems using the information from wide area measurement systems (WAMSs). The power method (PM) is adopted to compute the pair of conjugate eigenvalues with the algebraically largest real part and the corresponding eigenvectors of the Jacobian matrix of a power system. The distance between the current equilibrium point and the Hopf bifurcation set can be monitored dynamically by computing the pair of conjugate eigenvalues. When the current equilibrium point is close to the Hopf bifurcation set, the approximate normal vector to the Hopf bifurcation set is computed and used as a direction to regulate control parameters to avoid a Hopf bifurcation in the power system described by differential algebraic equations (DAEs). The validity of the proposed method is demonstrated by regulating the reactive power loads in a 14-bus power system.

  17. A System for Wireless Power Transfer and Data Communication of Long-Term Bio-Monitoring

    OpenAIRE

    2015-01-01

    A system for wireless power transfer and data communication of implantable bio-monitoring systems is presented. The proposed solution uses a servo-controlled power transmitter moved under the animal moving space. An x-y movable magnetic coil transmits the required power with a level able to keep constant the received energy by the bio-sensor system. The power is transferred via the optimized remote powering link at 13.56 MHz. The received AC signal is converted to DC voltage with a passive fu...

  18. Spacecraft Power Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I project will develop the Spacecraft Power Monitor (SPM) which will use non-intrusive electrical monitoring (NEMO). NEMO transforms the power...

  19. Optimized MPPT-based converter for TEG energy harvester to power wireless sensor and monitoring system in nuclear power plant

    Science.gov (United States)

    Xing, Shaoxu; Anakok, Isil; Zuo, Lei

    2017-04-01

    Accidents like Fukushima Disasters push people to improve the monitoring systems for the nuclear power plants. Thus, various types of energy harvesters are designed to power these systems and the Thermoelectric Generator (TEG) energy harvester is one of them. In order to enhance the amount of harvested power and the system efficiency, the power management stage needs to be carefully designed. In this paper, a power converter with optimized Maximum Power Point Tracking (MPPT) is proposed for the TEG Energy Harvester to power the wireless sensor network in nuclear power plant. The TEG Energy Harvester is installed on the coolant pipe of the nuclear plant and harvests energy from its heat energy while the power converter with optimized MPPT can make the TEG Energy Harvester output the maximum power, quickly response to the voltage change and provide sufficient energy for wireless sensor system to monitor the operation of the nuclear power plant. Due to the special characteristics of the Single-Ended Primary Inductor Converter (SEPIC) when it is working in the Discontinuous Inductor Current Mode (DICM) and Continuous Conduction Mode (CCM), the MPPT method presented in this paper would be able to control the converter to achieve the maximum output power in any working conditions of the TEG system with a simple circuit. The optimized MPPT algorithm will significantly reduce the cost and simplify the system as well as achieve a good performance. Experiment test results have shown that, comparing to a fixed- duty-cycle SEPIC which is specifically designed for the working on the secondary coolant loop in nuclear power plant, the optimized MPPT algorithm increased the output power by 55%.

  20. ZigBee Based Industrial Automation Profile for Power Monitoring Systems

    Directory of Open Access Journals (Sweden)

    Archana R. Raut,

    2011-05-01

    Full Text Available Industrial automations which are mostly depend upon the power systems & which requires distance controlled and regulated systems. Mostly voltage and current equipped parameters along with power and energy management system forms the industrial scenario for automations. Wireless technology which meets to cost, speed and distance scenario will always be a point of an interest for research. In this research work we mainly monitored power related parameters and enable remote switching devices for proper power management systems using ZigBee. This paper proposes a digital system for condition monitoring, diagnosis, and supervisory control for electric systems parameters like voltage and current using wireless sensor networks (WSNs based on ZigBee. Its main feature is its use of the ZigBee protocol as the communication medium between the transmitter and receiver modules. It illustrates that the new ZigBee standard performs well industrial environments.

  1. The Design of Partial Discharge On-Line Monitoring System for XLPE Power Cable

    OpenAIRE

    Chen Rui-Long; Qian Yong; Ye Hai-Feng; Sheng Ge-Hao; Jiang Xiu-Chen

    2013-01-01

    Partial discharge detection is an important means to assess the situation of XLPE power cable’s insulation. This study has developed an on-line monitoring system which applies to the medium voltage XLPE cable on partial discharge, described its working principle, components of hardware, software designing and program implementation in details. Through monitoring the partial discharge signal in grounding lines of the XLPE cable’s shield, the system integrated assess the situation of XLPE cable...

  2. Grid Monitoring and Advanced Control of Distributed Power Generation Systems

    DEFF Research Database (Denmark)

    Timbus, Adrian Vasile

    . First part of the thesis investigates possible algorithms for fast and accurate identi cation of utility network variables such as voltage amplitude, frequency, phase angle and line impedance. Special attention has been paid to grid synchronization algorithm in terms of accurate estimation of grid...... of grid voltage and the frequency of utility network. As a result, fast and accurate identi cation of both variables has been achieved. In addition, positive and negative sequence components of grid voltage can also be calculated. Simple, yet powerful ltering techniques, based on second order generalized...... integrator (SOGI) and delay signal cancellation (DSC) have been used to separate the sequence components. Simulation and experimental results attest the accuracy and e ectiveness of the developed algorithms in identifying the frequency, phase angle and magnitude of grid voltages during severe distortions...

  3. Design of a Human Machine Interface for a Reliability Monitoring System of Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Yuxin; Yang, Ming; Yan, Shengyuan [Harbin Engineering University, Harbin (Switzerland)

    2014-08-15

    This paper presents the design of a Reliability Monitoring System (RMS) for nuclear power plant which was newly developed by authors. The RMS, combining a dynamic reliability analysis system with an online fault management system, can assist technical personnel with their daily tasks such as system configuration management, maintenance plan making and state monitoring from a point of view that degradation of equipment performance, bad plant configurations and incorrect actions will decrease the probability of systems performing designed functions. For utilizing the RMS, technical personnel will monitor the plant operational state, conform the fault diagnosis, input the intended operating or maintenance actions, and monitor the probability changes of systems through a graphical HMI. A HMI evaluation experiment was conducted using an eye tracking system and a full scale simulator of PWR NPP. Visual data was recorded and analyzed after the experiment. The experiment results are presented and the HMI design problems revealed by the evaluation experiment are discussed.

  4. Automating security monitoring and analysis for Space Station Freedom's electric power system

    Science.gov (United States)

    Dolce, James L.; Sobajic, Dejan J.; Pao, Yoh-Han

    1990-01-01

    Operating a large, space power system requires classifying the system's status and analyzing its security. Conventional algorithms are used by terrestrial electric utilities to provide such information to their dispatchers, but their application aboard Space Station Freedom will consume too much processing time. A novel approach for monitoring and analysis using adaptive pattern techniques is presented. This approach yields an on-line security monitoring and analysis algorithm that is accurate and fast; and thus, it can free the Space Station Freedom's power control computers for other tasks.

  5. Development of On-Line Monitoring Systems for High Temperature Components in Power Plants

    Directory of Open Access Journals (Sweden)

    Hongcai Zhang

    2013-11-01

    Full Text Available To accurately detect deformation and extend the component life beyond the original design limits, structural safety monitoring techniques have attracted considerable attention in the power and process industries for decades. In this paper an on-line monitoring system for high temperature pipes in a power plant is developed. The extension-based sensing devices are amounted on straight pipes, T-Joints and elbows of a main steam pipeline. During on-site monitoring for more than two years, most of the sensors worked reliably and steadily. However, the direct strain gauge could not work for long periods because of the high temperature environment. Moreover, it is found that the installation and connection of the extensometers can have a significant influence on the measurement results. The on-line monitoring system has a good alarming function which is demonstrated by detecting a steam leakage of the header.

  6. Development of on-line monitoring systems for high temperature components in power plants.

    Science.gov (United States)

    Zhang, Hongcai; Jia, Jiuhong; Wang, Ning; Hu, Xiaoyin; Tu, Shan-Tung; Zhou, Shaoping; Wang, Zhengdong

    2013-11-13

    To accurately detect deformation and extend the component life beyond the original design limits, structural safety monitoring techniques have attracted considerable attention in the power and process industries for decades. In this paper an on-line monitoring system for high temperature pipes in a power plant is developed. The extension-based sensing devices are amounted on straight pipes, T-Joints and elbows of a main steam pipeline. During on-site monitoring for more than two years, most of the sensors worked reliably and steadily. However, the direct strain gauge could not work for long periods because of the high temperature environment. Moreover, it is found that the installation and connection of the extensometers can have a significant influence on the measurement results. The on-line monitoring system has a good alarming function which is demonstrated by detecting a steam leakage of the header.

  7. Development of On-Line Monitoring Systems for High Temperature Components in Power Plants

    Science.gov (United States)

    Zhang, Hongcai; Jia, Jiuhong; Wang, Ning; Hu, Xiaoyin; Tu, Shan-Tung; Zhou, Shaoping; Wang, Zhengdong

    2013-01-01

    To accurately detect deformation and extend the component life beyond the original design limits, structural safety monitoring techniques have attracted considerable attention in the power and process industries for decades. In this paper an on-line monitoring system for high temperature pipes in a power plant is developed. The extension-based sensing devices are amounted on straight pipes, T-Joints and elbows of a main steam pipeline. During on-site monitoring for more than two years, most of the sensors worked reliably and steadily. However, the direct strain gauge could not work for long periods because of the high temperature environment. Moreover, it is found that the installation and connection of the extensometers can have a significant influence on the measurement results. The on-line monitoring system has a good alarming function which is demonstrated by detecting a steam leakage of the header. PMID:24233026

  8. Developing a PQ monitoring system for assessing power quality and critical areas detection

    Directory of Open Access Journals (Sweden)

    Miguel Romero

    2011-10-01

    Full Text Available This paper outlines the development of a power quality monitoring system. The system is aimed at assessing power quality and detecting critical areas throughout at distribution system. Such system integrates a hardware system and a software processing tool developed in four main stages. Power quality disturbances are registered by PQ meters and the data is transmitted through a 3G wireless network. This data is processed and filtered in an open source database. Some interesting statistical indices related to voltage sags, swells, flicker and voltage unbalance are obtained. The last stage displays the indices geo-referenced on power quality maps, allowing the identification of critical areas according to different criteria. The results can be analyzed using clustering tools to identify differentiated quality groups in a city. The proposed system is an open source tool useful to electricity utilities to analyze and manage large amount of data.

  9. Development of a remote controlled robot system for monitoring nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Woo, Hee Gon; Song, Myung Jae; Shin, Hyun Bum; Oh, Gil Hwan; Maeng, Sung Jun; Choi, Byung Jae; Chang, Tae Woo [Korea Electric Power Research Institute, Taejon (Korea, Republic of); Lee, Bum Hee; Yoo, Jun; Choi, Myung Hwan; Go, Nak Yong; Lee, Kee Dong; Lee, Young Dae; Cho, Hae Kyeng; Nam, Yoon Suk [Electric and Science Research Center, (Korea, Republic of)

    1996-12-31

    It`s a final report of the development of remote controlled robot system for monitoring the facilities in nuclear power plant and contains as follows, -Studying the technologies in robot developments and analysing the requirements and working environments - Development of the test mobile robot system - Development of the mobile-robot - Development of the Mounted system on the Mobile robot - Development of the Monitoring system - Mobil-robot applications and future study. In this study we built the basic technologies and schemes for future robot developments and applications. (author). 20 refs., figs.

  10. A New Remote Monitoring System Application in Laser Power Based on LabVIEW

    Directory of Open Access Journals (Sweden)

    Liu Gaoqiang

    2016-01-01

    Full Text Available In this paper, a new remote monitoring system based on LabVIEW was proposed to measure laser power automatically and remotely. This system consists of four basic components: an DH-JG2 optical power meter, a NI-USB 6008 data acquisition card, a personal computer (PC, and HP laserJet 1020 Plus printer. Since power output of laser is generally so unstable that abnormal work situation could not retroaction to inspectors right away, new system was designed to solve this problem. The detection system realized function of remote control by TCP protocol and mobile phone. Laser power curve that is measured by detection system demonstrated that the design has a good performance in real-time detection and operability.

  11. A Design of Wireless Sensor Networks for a Power Quality Monitoring System

    Directory of Open Access Journals (Sweden)

    Sanggil Kang

    2010-11-01

    Full Text Available Power grids deal with the business of generation, transmission, and distribution of electric power. Recently, interest in power quality in electrical distribution systems has increased rapidly. In Korea, the communication network to deliver voltage, current, and temperature measurements gathered from pole transformers to remote monitoring centers employs cellular mobile technology. Due to high cost of the cellular mobile technology, power quality monitoring measurements are limited and data gathering intervals are large. This causes difficulties in providing the power quality monitoring service. To alleviate the problems, in this paper we present a communication infrastructure to provide low cost, reliable data delivery. The communication infrastructure consists of wired connections between substations and monitoring centers, and wireless connections between pole transformers and substations. For the wireless connection, we employ a wireless sensor network and design its corresponding data forwarding protocol to improve the quality of data delivery. For the design, we adopt a tree-based data forwarding protocol in order to customize the distribution pattern of the power quality information. We verify the performance of the proposed data forwarding protocol quantitatively using the NS-2 network simulator.

  12. Low power and self-reconfigurable WBAN controller for continuous bio-signal monitoring system.

    Science.gov (United States)

    Lee, Seulki; Yoo, Hoi-Jun

    2013-04-01

    The WBAN controller with Branched Bus (BB) topology and Continuous Data Transmission (CDT) protocol with low power consumption and self-reconfigurability is proposed for wearable healthcare applications. The BB topology and CDT protocol is a combination of conventional Bus and Star topology and a variation from TDMA protocol, respectively, while they are able to compensate for the electrical fault in bio-signal monitoring system caused by the electrode deformation. Thanks to them, the proposed WBAN controller enables more reliable operation in continuous bio-signal monitoring applications such as sleep monitoring.

  13. The Design of Partial Discharge On-Line Monitoring System for XLPE Power Cable

    Directory of Open Access Journals (Sweden)

    Chen Rui-Long

    2013-09-01

    Full Text Available Partial discharge detection is an important means to assess the situation of XLPE power cable’s insulation. This study has developed an on-line monitoring system which applies to the medium voltage XLPE cable on partial discharge, described its working principle, components of hardware, software designing and program implementation in details. Through monitoring the partial discharge signal in grounding lines of the XLPE cable’s shield, the system integrated assess the situation of XLPE cable’s insulation. The results of running show that the system is stable and reliable.

  14. FDD-1 System On-line Monitoring Fuel Rod Failure of Nuclear Power Plant

    Institute of Scientific and Technical Information of China (English)

    CHENPeng; ZHANGYing-chao; JISong-tao; GAOYong-guang; YINZhen-guo; HANChuan-bin

    2003-01-01

    The FDD-1 system developed by CIAE for on-line monitoring fuel rod failure of nuclear power plant consists of γ-ray detector, γ-ray spectrum analyzer, computer, and an analysis code for evaluating the status of fuel rod failure. It would be determined that the fuel rod failure occurs when a large amount of γ activity increases in the primary system measured by γ-ray detector near the CVCS.

  15. Monitoring the power system stability; Monitoramento da estabilidade dos sistemas de potencia

    Energy Technology Data Exchange (ETDEWEB)

    Bretas, Newton G. [Sao Paulo Univ., Sao Carlos, SP (Brazil). Escola de Engenharia

    1994-12-31

    This work presents a method to monitor the stability of a power system, after a major disturbance, using of adaptive time series approach. The model parameters are updated every time the prediction stage is completed. Besides, according to the values of the parameters, one may conclude the system will be unstable, will go to be a damped sine wave or even a damped exponential. (author) 29 refs., 12 figs., 3 tabs.

  16. A new monitoring system for piping systems in fossil-fired power plants

    Energy Technology Data Exchange (ETDEWEB)

    Redon, J.G. [Empresarios Agrupados, (Spain); Maile, K.; Purper, K. [Staatliche Materialsprufungsanstalt, University of Stuttgart, (Germany); Wilson, B. [Babcok Energy LTD, United Kindom (United Kingdom); Rohler, K. [Deustsche Babcock Werke Ag, Germany (Greece); Lehmann, H. [Rheinisch-Westfalischer Tuv, Germany (Germany); Fernandez, J. [Union Fenosa,Spain (Spain)

    1996-12-31

    A CEC-funded project have been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified were existing Life Monitoring System technology could be improved. These were: 1. the inclusion of creep relaxation 2. the inclusion of external loads on components

  17. Development of an automated system for continuous monitoring of powered roof support in longwall panel

    Institute of Scientific and Technical Information of China (English)

    ATUL Kumar; DHEERAJ Kumar; SINGH U.K.; GUPTA P.S.

    2010-01-01

    Described the development of an Intrinsically Safe System for continuous monitoring of load and convergence of powered roof supports installed at longwall faces.The system developed for monitoring of behavior of a powered support in a mechanized longwall sublevel caving face. The logging system can be programmed for logging the data from the sensors at different logging intervals ranging from 16 h to 1 ms for logging variation in hydraulic pressures in legs and convergence of the support during progressive face advance. For recording dynamic loads, the data logger can be programmed to start fast logging, say at 10 ms intervals, when the pressure in a leg reaches a pre-specified threshold value, and continue fast logging until the pressure drops below this threshold value. This fast logging automatically stops when the pressure drops below this threshold value.

  18. Intelligent Monitoring System With High Temperature Distributed Fiberoptic Sensor For Power Plant Combustion Processes

    Energy Technology Data Exchange (ETDEWEB)

    Kwang Y. Lee; Stuart S. Yin; Andre Boheman

    2005-12-26

    The objective of the proposed work is to develop an intelligent distributed fiber optical sensor system for real-time monitoring of high temperature in a boiler furnace in power plants. Of particular interest is the estimation of spatial and temporal distributions of high temperatures within a boiler furnace, which will be essential in assessing and controlling the mechanisms that form and remove pollutants at the source, such as NOx. The basic approach in developing the proposed sensor system is three fold: (1) development of high temperature distributed fiber optical sensor capable of measuring temperatures greater than 2000 C degree with spatial resolution of less than 1 cm; (2) development of distributed parameter system (DPS) models to map the three-dimensional (3D) temperature distribution for the furnace; and (3) development of an intelligent monitoring system for real-time monitoring of the 3D boiler temperature distribution. Under Task 1, we set up a dedicated high power, ultrafast laser system for fabricating in-fiber gratings in harsh environment optical fibers, successfully fabricated gratings in single crystal sapphire fibers by the high power laser system, and developed highly sensitive long period gratings (lpg) by electric arc. Under Task 2, relevant mathematical modeling studies of NOx formation in practical combustors. Studies show that in boiler systems with no swirl, the distributed temperature sensor may provide information sufficient to predict trends of NOx at the boiler exit. Under Task 3, we investigate a mathematical approach to extrapolation of the temperature distribution within a power plant boiler facility, using a combination of a modified neural network architecture and semigroup theory. The 3D temperature data is furnished by the Penn State Energy Institute using FLUENT. Given a set of empirical data with no analytic expression, we first develop an analytic description and then extend that model along a single axis. Extrapolation

  19. Towards a Cyber Defense Framework for SCADA Systems Based on Power Consumption Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez Jimenez, Jarilyn M [ORNL; Chen, Qian [Savannah State University; Nichols, Jeff A. {Cyber Sciences} [ORNL; Calhoun, Chelsea [Savannah State University; Sykes, Summer [Savannah State University

    2017-01-01

    Supervisory control and data acquisition (SCADA) is an industrial automation system that remotely monitor, and control critical infrastructures. SCADA systems are major targets for espionage and sabotage attackers. According to the 2015 Dell security annual threat report, the number of cyber-attacks against SCADA systems has doubled in the past year. Cyber-attacks (i.e., buffer overflow, rootkits and code injection) could cause serious financial losses and physical infrastructure damages. Moreover, some specific cyber-attacks against SCADA systems could become a threat to human life. Current commercial off-the-shelf security solutions are insufficient in protecting SCADA systems against sophisticated cyber-attacks. In 2014 a report by Mandiant stated that only 69% of organizations learned about their breaches from third entities, meaning that these companies lack of their own detection system. Furthermore, these breaches are not detected in real-time or fast enough to prevent further damages. The average time between compromise and detection (for those intrusions that were detected) was 205 days. To address this challenge, we propose an Intrusion Detection System (IDS) that detects SCADA-specific cyber-attacks by analyzing the power consumption of a SCADA device. Specifically, to validate the proposed approach, we chose to monitor in real-time the power usage of a a Programmable Logic Controller (PLC). To this end, we configured the hardware of the tetsbed by installing the required sensors to monitor and collect its power consumption. After that two SCADA-specific cyber-attacks were simulated and TracerDAQ Pro was used to collect the power consumption of the PLC under normal and anomalous scenarios. Results showed that is possible to distinguish between the regular power usage of the PLC and when the PLC was under specific cyber-attacks.

  20. An RF powering system with adaptive impedance matching for individual health monitoring applications.

    Science.gov (United States)

    Zemin Liu; Yu-Pin Hsu; Hella, Mona M

    2016-08-01

    This paper presents a high-efficiency RF powering system, suitable for individual health monitoring applications. The system is composed of an antenna, an impedance matching network, and a two-stage full-wave RF-DC rectifier. A novel tuning mechanism is proposed to automatically adjust the impedance of the matching network. This mechanism can effectively improve the power efficiency of the system by 47% compared to the case without tuning. For the adaptive impedance, only a 5-bits binary weighted capacitor bank is required in the matching network. The complete system, designed in a standard 0.13μm CMOS technology, converts a -6dBm 915MHz RF signal to a 1.7V DC voltage with an output current of 85μA. The simulated maximum power efficiency of the complete RF harvester is 66%.

  1. A feasibility study on the predictive emission monitoring system applied to the Hsinta power plant of Taiwan Power Company.

    Science.gov (United States)

    Chien, T W; Chu, H; Hsu, W C; Tseng, T K; Hsu, C H; Chen, K Y

    2003-08-01

    The continuous emission monitoring system (CEMS) can monitor flue gas emissions continuously and instantaneously. However, it has the disadvantages of enormous cost, easily producing errors in sampling periods of bad weather, lagging response in variable ambient environments, and missing data in daily zero and span tests and maintenance. The concept of a predictive emission monitoring system (PEMS) is to use the operating parameters of combustion equipment through thermodynamic or statistical methods to construct a mathematic model that can predict emissions by a computer program. The goal of this study is to set up a PEMS in a gas-fired combined cycle power generation unit at the Hsinta station of Taiwan Power Co. The emissions to be monitored include nitrogen oxides (NOx) and oxygen (O2) in flue gas. The major variables of the predictive model were determined based on the combustion theory. The data of these variables then were analyzed to establish a regression model. From the regression results, the influences of these variables are discussed and the predicted values are compared with the CEMS data for accuracy. In addition, according to the cost information, the capital and operation and maintenance costs for a PEMS can be much lower than those for a CEMS.

  2. Intelligent Monitoring System with High Temperature Distributed Fiberoptic Sensor for Power Plant Combustion Processes

    Energy Technology Data Exchange (ETDEWEB)

    Kwang Y. Lee; Stuart S. Yin; Andre Boehman

    2006-09-26

    The objective of the proposed work is to develop an intelligent distributed fiber optical sensor system for real-time monitoring of high temperature in a boiler furnace in power plants. Of particular interest is the estimation of spatial and temporal distributions of high temperatures within a boiler furnace, which will be essential in assessing and controlling the mechanisms that form and remove pollutants at the source, such as NOx. The basic approach in developing the proposed sensor system is three fold: (1) development of high temperature distributed fiber optical sensor capable of measuring temperatures greater than 2000 C degree with spatial resolution of less than 1 cm; (2) development of distributed parameter system (DPS) models to map the three-dimensional (3D) temperature distribution for the furnace; and (3) development of an intelligent monitoring system for real-time monitoring of the 3D boiler temperature distribution. Under Task 1, we have set up a dedicated high power, ultrafast laser system for fabricating in-fiber gratings in harsh environment optical fibers, successfully fabricated gratings in single crystal sapphire fibers by the high power laser system, and developed highly sensitive long period gratings (lpg) by electric arc. Under Task 2, relevant mathematical modeling studies of NOx formation in practical combustors have been completed. Studies show that in boiler systems with no swirl, the distributed temperature sensor may provide information sufficient to predict trends of NOx at the boiler exit. Under Task 3, we have investigated a mathematical approach to extrapolation of the temperature distribution within a power plant boiler facility, using a combination of a modified neural network architecture and semigroup theory. Given a set of empirical data with no analytic expression, we first developed an analytic description and then extended that model along a single axis.

  3. Real-Time Monitoring System for a Utility-Scale Photovoltaic Power Plant

    Directory of Open Access Journals (Sweden)

    Isabel M. Moreno-Garcia

    2016-05-01

    Full Text Available There is, at present, considerable interest in the storage and dispatchability of photovoltaic (PV energy, together with the need to manage power flows in real-time. This paper presents a new system, PV-on time, which has been developed to supervise the operating mode of a Grid-Connected Utility-Scale PV Power Plant in order to ensure the reliability and continuity of its supply. This system presents an architecture of acquisition devices, including wireless sensors distributed around the plant, which measure the required information. It is also equipped with a high-precision protocol for synchronizing all data acquisition equipment, something that is necessary for correctly establishing relationships among events in the plant. Moreover, a system for monitoring and supervising all of the distributed devices, as well as for the real-time treatment of all the registered information, is presented. Performances were analyzed in a 400 kW transformation center belonging to a 6.1 MW Utility-Scale PV Power Plant. In addition to monitoring the performance of all of the PV plant’s components and detecting any failures or deviations in production, this system enables users to control the power quality of the signal injected and the influence of the installation on the distribution grid.

  4. Real-Time Monitoring System for a Utility-Scale Photovoltaic Power Plant.

    Science.gov (United States)

    Moreno-Garcia, Isabel M; Palacios-Garcia, Emilio J; Pallares-Lopez, Victor; Santiago, Isabel; Gonzalez-Redondo, Miguel J; Varo-Martinez, Marta; Real-Calvo, Rafael J

    2016-05-26

    There is, at present, considerable interest in the storage and dispatchability of photovoltaic (PV) energy, together with the need to manage power flows in real-time. This paper presents a new system, PV-on time, which has been developed to supervise the operating mode of a Grid-Connected Utility-Scale PV Power Plant in order to ensure the reliability and continuity of its supply. This system presents an architecture of acquisition devices, including wireless sensors distributed around the plant, which measure the required information. It is also equipped with a high-precision protocol for synchronizing all data acquisition equipment, something that is necessary for correctly establishing relationships among events in the plant. Moreover, a system for monitoring and supervising all of the distributed devices, as well as for the real-time treatment of all the registered information, is presented. Performances were analyzed in a 400 kW transformation center belonging to a 6.1 MW Utility-Scale PV Power Plant. In addition to monitoring the performance of all of the PV plant's components and detecting any failures or deviations in production, this system enables users to control the power quality of the signal injected and the influence of the installation on the distribution grid.

  5. Application of Compressive Sampling in Computer Based Monitoring of Power Systems

    Directory of Open Access Journals (Sweden)

    Sarasij Das

    2014-01-01

    Full Text Available Shannon’s Nyquist theorem has always dictated the conventional signal acquisition policies. Power system is not an exception to this. As per this theory, the sampling rate must be at least twice the maximum frequency present in the signal. Recently, compressive sampling (CS theory has shown that the signals can be reconstructed from samples obtained at sub-Nyquist rate. Signal reconstruction in this theory is exact for “sparse signals” and is near exact for compressible signals provided certain conditions are satisfied. CS theory has already been applied in communication, medical imaging, MRI, radar imaging, remote sensing, computational biology, machine learning, geophysical data analysis, and so forth. CS is comparatively new in the area of computer based power system monitoring. In this paper, subareas of computer based power system monitoring where compressive sampling theory has been applied are reviewed. At first, an overview of CS is presented and then the relevant literature specific to power systems is discussed.

  6. Real time simulation application to monitor the stability limit of power system

    Science.gov (United States)

    Hartono, Kuo, Ming-Tse

    2017-06-01

    If the power system falls into an unsteady state, there will be voltage collapse in which the power system will be separated into small systems. Identifying the stability reserve in conformity with a certain practical operation condition is very important for the system management and operation. In fact, the global power system issue has caused serious outages due to voltage collapse such as in the United States-Canada in August 14, 2003; South London in August 28, 2003; southern Sweden and eastern Denmark in September 23, 2003; and Italy on September 28, 2003, and in Vietnam where power system problem led to power loss on 17 May 2005, 27 December 2006, 20 July 2007, and 10 September 2007. The analysis shows that the phenomenon is related to the loss of system stability. Thus, the operational system as well as the power system designs should be studied related to the issue of the system stability. To study the static stability of the power system, different approximate standards, called pragmatic criteria, were examined. Markovits has investigated the application of the standard of dP/dd to test the stability of the power button and dq/dU to check the voltage stability of the load button [1]. However, the storage stability when calculating standard dP/d d is usually much larger than the reserves when calculating standard dq/dU [1]. This paper presents a method to build a possible operation region in the power plane of load bus which works in comply with the stability limit to evaluate the stability reserve of the power system. This method is used to build a program to monitor the stability reserve of IEEE 39 Bus Power System in real time. To monitor the stability reserve of IEEE 39 nodes power system, articles based on the standard dq/dU was used to calculate the assessment. When using standard dq/dU to check for voltage stability load button, the amount of storage stability can be calculated by the following steps: first, transformed replacement scheme Masonry on

  7. A technical system to improve the operational monitoring of the Zaporozhye nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Beyer, M.; Carl, H.; Nowak, K. [Technischer Ueberwachungsverein Rheinland, Koeln (Germany). Inst. for Nuclear Engineering and Radiation Protection; Schumann, P.; Seidel, A.; Weiss, F.P.; Zschau, J.

    1998-10-01

    As part of the programme implemented by the German Ministry of Environment, Nature Conservation and Reactor Safety to cooperate with the Central and Eastern European States (CEES) and the Commonwealth of Independent States (CIS) in the area of nuclear safety, a technical system to improve operational monitoring has been designed, specified and established since 1992 as a pilot project in the Zaporozhye/Ukraine nuclear power plant by Forschungszentrum Rossendorf and Technischer Ueberwachungsverein Rheinland with a significant contribution from the State Scientific and Technical Centre of the Ukrainian supervisory authority. The technical system complements existing operational checking and monitoring facilities by including modern means of information technology. It enables a continuous monitoring of the state of unit 5 in normal operation and in cases of anomalies or incidents so that when recognisable deviations from the regular plant operation occur, the Ukrainian supervisory authority can immediately inquire and if necessary impose conditions on the operator. The radiological and meteorological parameters at the nuclear power plant location are monitored to the extent necessary to assess the current radiation situation and to implement efficient emergency management measures. (orig.)

  8. Development of a Functional Platform for System Reliability Monitoring of Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Ming; Zhang, Zhijian; Yoshikawa, Hidekazu [Harbin Engineering University, Harbin (China)

    2014-08-15

    This paper presents MFM builder, a platform based on Multilevel Flow Modeling (MFM), which provides a graphical interface for modeling functions of complex artificial systems such as nuclear power plant with emphasizing the designed purposes of systems. Several algorithms based on MFM have been developed for dynamic system reliability analysis, fault diagnosis and quantitative software reliability analysis. A Reliability Monitoring System (RMS) of PWR nuclear power plant was developed by integrating above algorithms. Experiments by connecting RMS with a full scale PWR simulator showed that it took 16 seconds for RMS calculating the reliability changes over time of safety-related systems according to given system configurations in the 31 days by one computer run. The proposed reliability monitoring system can be used not only offline as a reliability analysis tool to assist the plant maintenance staffs in maintenance plan making, but also online as a operator support system to assist the operators in Main Control Room (MCR) in their various tasks such as configuration management, fault diagnosis and operational decision making.

  9. A wearable wireless ECG monitoring system with dynamic transmission power control for long-term homecare.

    Science.gov (United States)

    Wang, Yishan; Doleschel, Sammy; Wunderlich, Ralf; Heinen, Stefan

    2015-03-01

    This paper presents a wearable wireless ECG monitoring system based on novel 3-Lead electrode placements for long-term homecare. The experiment for novel 3-Lead electrode placements is carried out, and the results show that the distance between limb electrodes can be significantly reduced. Based on the new electrode position, a small size sensor node, which is powered by a rechargeable battery, is designed to detect, amplify, filter and transmit the ECG signals. The coordinator receives the data and sends it to PC. Finally the signals are displayed on the GUI. In order to control the power consumption of sensor node, a dynamic power adjustment method is applied to automatically adjust the transmission power of the sensor node according to the received signal strength indicator (RSSI), which is related to the distance and obstacle between sensor node and coordinator. The system is evaluated when the user, who wears the sensor, is walking and running. A promising performance is achieved even under body motion. The power consumption can be significantly reduced with this dynamic power adjustment method.

  10. An inductively powered telemetry system for temperature, EKG, and activity monitoring

    Science.gov (United States)

    Fryer, T. B.; Lund, G. F.; Williams, B. A.

    1978-01-01

    An implant telemetry system for the simultaneous monitoring of temperature, activity, and EKG from small animals, such as rats, was designed with the feature that instead of a battery the system is energized by an inductive field. A 250 kHz resonant coil surrounds the cage (30 x 30 x 20 cm) and provides the approximately 100 microns of power required to operate the implant transmitter while allowing the animal unrestrained movement in the cage. The implant can also be battery operated if desired. RF transmission is in the 8-10 MHz band, which allows the use of a simple, essentially single IC chip, receiver.

  11. TEG BASED POWER SYSTEM for OPERATION of HEALTH MONITORING SERVER in INDUSTRIES

    Directory of Open Access Journals (Sweden)

    P.S.Raghavendran

    2014-01-01

    Full Text Available In Hazardous environment industries where the emission of toxic gases and effluents will have an impact on the health of the operators, the recording of health parameters of individual operators is very important. In such situation the health monitoring of operators are being monitored and processed centrally by a server and this can be powered by a system of batteries which can be operated from TEG to ensure reliability and to utilize the exhaust heat energy of industries for better performance. This paper describes the Thermo electric generator with battery that supports medical server. The thermoelectric generator converts heat energy into electrical energy. Mathematical model of thermoelectric generator was developed in MATLAB SIMULINK. This exhibits different voltage and current for various temperature differences. The proposed system uses maximum power point tracking algorithm to obtain the maximum power from the thermoelectric generator. This algorithm is developed in embedded MATLAB controller, which gives the firing angle to the DC-DC Boost converter for various temperature differences. This will increase the efficiency of the system.

  12. Design of a telemetry system based on wireless power transmission for physiological parameter monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Zhiwei, E-mail: jiayege@hotmail.com [College of Electrical and Information Engineering, Changsha University of Science and Technology, Changsha (China); Yan, Guozheng; Zhu, Bingquan [820 Institute, School of Electronic Information and Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China)

    2015-04-15

    An implanted telemetry system for experimental animals with or without anaesthesia can be used to continuously monitor physiological parameters. This system is significant not only in the study of organisms but also in the evaluation of drug efficacy, artificial organs, and auxiliary devices. The system is composed of a miniature electronic capsule, a wireless power transmission module, a data-recording device, and a processing module. An electrocardiograph, a temperature sensor, and a pressure sensor are integrated in the miniature electronic capsule, in which the signals are transmitted in vitro by wireless communication after filtering, amplification, and A/D sampling. To overcome the power shortage of batteries, a wireless power transmission module based on electromagnetic induction was designed. The transmitting coil of a rectangular-section solenoid and a 3D receiving coil are proposed according to stability and safety constraints. Experiments show that at least 150 mW of power could pick up on the load in a volume of Φ10.5 mm × 11 mm, with a transmission efficiency of 2.56%. Vivisection experiments verified the feasibility of the integrated radio-telemetry system.

  13. INTELLIGENT MONITORING SYSTEM WITH HIGH TEMPERATURE DISTRIBUTED FIBEROPTIC SENSOR FOR POWER PLANT COMBUSTION PROCESSES

    Energy Technology Data Exchange (ETDEWEB)

    Kwang Y. Lee; Stuart S. Yin; Andre Boheman

    2004-12-26

    The objective of the proposed work is to develop an intelligent distributed fiber optical sensor system for real-time monitoring of high temperature in a boiler furnace in power plants. Of particular interest is the estimation of spatial and temporal distributions of high temperatures within a boiler furnace, which will be essential in assessing and controlling the mechanisms that form and remove pollutants at the source, such as NOx. The basic approach in developing the proposed sensor system is three fold: (1) development of high temperature distributed fiber optical sensor capable of measuring temperatures greater than 2000 C degree with spatial resolution of less than 1 cm; (2) development of distributed parameter system (DPS) models to map the three-dimensional (3D) temperature distribution for the furnace; and (3) development of an intelligent monitoring system for real-time monitoring of the 3D boiler temperature distribution. Under Task 1, improvement was made on the performance of in-fiber grating fabricated in single crystal sapphire fibers, test was performed on the grating performance of single crystal sapphire fiber with new fabrication methods, and the fabricated grating was applied to high temperature sensor. Under Task 2, models obtained from 3-D modeling of the Demonstration Boiler were used to study relationships between temperature and NOx, as the multi-dimensionality of such systems are most comparable with real-life boiler systems. Studies show that in boiler systems with no swirl, the distributed temperature sensor may provide information sufficient to predict trends of NOx at the boiler exit. Under Task 3, we investigate a mathematical approach to extrapolation of the temperature distribution within a power plant boiler facility, using a combination of a modified neural network architecture and semigroup theory. The 3D temperature data is furnished by the Penn State Energy Institute using FLUENT. Given a set of empirical data with no analytic

  14. Power system low frequency oscillation monitoring and analysis based on multi-signal online identification

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The advance in the wide-area measurement system (WAMS) is driving the power system to the trend of wide-area monitoring and control.The Prony method is usually used for low frequency oscillation online identification.However,the identified amplitude and phase information is not sufficiently used.In this paper,the amplitude is adopted to detect the occurrence of the oscillation and to obtain the mode observability of the sites.The phase is adopted to identify the oscillation generator grouping and to obtain the mode shapes.The time varying characteristics of low frequency oscillations are studied.The behaviors and the characters of low frequency oscillations are displayed by dynamic visual techniques.Demonstrations on the "11.9" low frequency oscillation of the Guizhou Power Grid substantiate the feasibility and the validation of the proposed methods.

  15. Condition based maintenance optimization for wind power generation systems under continuous monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Zhigang; Wu, Bairong; Ding, Fangfang [Concordia Institute for Information Systems Engineering, Concordia University, 1515 Ste-Catherine Street, West EV-7.637, Montreal (Canada); Jin, Tongdan [Ingram School of Engineering, Texas State University (United States)

    2011-05-15

    By utilizing condition monitoring information collected from wind turbine components, condition based maintenance (CBM) strategy can be used to reduce the operation and maintenance costs of wind power generation systems. The existing CBM methods for wind power generation systems deal with wind turbine components separately, that is, maintenance decisions are made on individual components, rather than the whole system. However, a wind farm generally consists of multiple wind turbines, and each wind turbine has multiple components including main bearing, gearbox, generator, etc. There are economic dependencies among wind turbines and their components. That is, once a maintenance team is sent to the wind farm, it may be more economical to take the opportunity to maintain multiple turbines, and when a turbine is stopped for maintenance, it may be more cost-effective to simultaneously replace multiple components which show relatively high risks. In this paper, we develop an optimal CBM solution to the above-mentioned issues. The proposed maintenance policy is defined by two failure probability threshold values at the wind turbine level. Based on the condition monitoring and prognostics information, the failure probability values at the component and the turbine levels can be calculated, and the optimal CBM decisions can be made accordingly. A simulation method is developed to evaluate the cost of the CBM policy. A numerical example is provided to illustrate the proposed CBM approach. A comparative study based on commonly used constant-interval maintenance policy demonstrates the advantage of the proposed CBM approach in reducing the maintenance cost. (author)

  16. Low-Power Wearable Systems for Continuous Monitoring of Environment and Health for Chronic Respiratory Disease.

    Science.gov (United States)

    Dieffenderfer, James; Goodell, Henry; Mills, Steven; McKnight, Michael; Yao, Shanshan; Lin, Feiyan; Beppler, Eric; Bent, Brinnae; Lee, Bongmook; Misra, Veena; Zhu, Yong; Oralkan, Omer; Strohmaier, Jason; Muth, John; Peden, David; Bozkurt, Alper

    2016-09-01

    We present our efforts toward enabling a wearable sensor system that allows for the correlation of individual environmental exposures with physiologic and subsequent adverse health responses. This system will permit a better understanding of the impact of increased ozone levels and other pollutants on chronic asthma conditions. We discuss the inefficiency of existing commercial off-the-shelf components to achieve continuous monitoring and our system-level and nano-enabled efforts toward improving the wearability and power consumption. Our system consists of a wristband, a chest patch, and a handheld spirometer. We describe our preliminary efforts to achieve a submilliwatt system ultimately powered by the energy harvested from thermal radiation and motion of the body with the primary contributions being an ultralow-power ozone sensor, an volatile organic compounds sensor, spirometer, and the integration of these and other sensors in a multimodal sensing platform. The measured environmental parameters include ambient ozone concentration, temperature, and relative humidity. Our array of sensors also assesses heart rate via photoplethysmography and electrocardiography, respiratory rate via photoplethysmography, skin impedance, three-axis acceleration, wheezing via a microphone, and expiratory airflow. The sensors on the wristband, chest patch, and spirometer consume 0.83, 0.96, and 0.01 mW, respectively. The data from each sensor are continually streamed to a peripheral data aggregation device and are subsequently transferred to a dedicated server for cloud storage. Future work includes reducing the power consumption of the system-on-chip including radio to reduce the entirety of each described system in the submilliwatt range.

  17. Toward a Wirelessly Powered On-Lens Intraocular Pressure Monitoring System.

    Science.gov (United States)

    Chiou, Jin-Chern; Hsu, Shun-Hsi; Liao, Yu-Te; Huang, Yu-Chieh; Yeh, Guan-Ting; Kuei, Cheng-Kai; Dai, Kai-Shiun

    2016-09-01

    This paper presents a wireless on-lens intraocular pressure monitoring system, comprising a capacitance-to-digital converter and a wirelessly powered radio-frequency identification (RFID)-compatible communication system, for sensor control and data communication. The capacitive sensor was embedded on a soft contact lens of 200 μm thickness using commercially available biocompatible lens material, to improve compliance and reduce user discomfort. The sensor chip was shown to achieve effective number of bits greater than 10 over a capacitance range up to 50 pF while consuming only 64-μW power. The on-lens capacitive sensor could detect dielectric variation caused by changes in water content from a distance of 2 cm by using incident power from an RFID reader at 20 dBm. The maximum detectable distance was 11 cm with 30-dBm incident RF power. The rise in eye tissue temperature under 30-dBm RF exposure over an interval of 1 s was simulated and found to be less than 0.01°C.

  18. An ultra low-power front-end IC for wearable health monitoring system.

    Science.gov (United States)

    Yu-Pin Hsu; Zemin Liu; Hella, Mona M

    2016-08-01

    This paper presents a low-power front-end IC for wearable health monitoring systems. The IC, designed in a standard 0.13μm CMOS technology, fully integrates a low-noise analog front-end (AFE) to process the weak bio-signals, followed by an analog-to-digital converter (ADC) to digitize the extracted signals. An AC-coupled driving buffer, that interfaces between the AFE and the ADC is introduced to scale down the power supply of the ADC. The power consumption decreases by 50% compared to the case without power supply scaling. The AFE passes signals from 0.5Hz to 280Hz and from 0.7Hz to 160Hz with a simulated input referred noise of 1.6μVrms and achieves a maximum gain of 35dB/41dB respectively, with a noise-efficiency factor (NEF) of the AFE is 1. The 8-bit ADC achieves a simulated 7.96-bit resolution at 10KS/s sampling rate under 0.5V supply voltage. The overall system consumes only 0.86μW at dual supply voltages of 1V (AFE) and 0.5 V (ADC).

  19. HVDC System Stability – Analysis, Monitoring and Control in Wide Area Power Systems

    OpenAIRE

    Kuehn, Walter; Vanfretti, Luigi; Fischer, W.

    2014-01-01

    To a great extent future electric power systems will use HVDC technologies, based on either current sourced or voltage sourced converters (CSC, resp. VSC). Both technologies have their merits and range of applications being connected to technical capabilities, costs and operational properties and performance. Voltage stability is an important issue in classical CSC-based HVDC systems, while voltage stability and angle stability (both transmission angle and rotor angle) are of concern in VSC-H...

  20. Design of a DCS Based Model for Continuous Leakage Monitoring System of Rotary Air Preheater of a Thermal Power Plant

    Directory of Open Access Journals (Sweden)

    Madan BHOWMICK

    2011-01-01

    Full Text Available The leakage in rotary air preheater makes a considerable contribution to the reduced overall efficiency of fossil-fuel-fired thermal power plants and increase the effect on environment. Since it is normal phenomenon, continuous monitoring of leakage is generally omitted in most power plants. But for accurate analysis of the operation of the thermal power plant, this leakage monitoring plays a vital role. In the present paper, design of a DCS based model for continuous leakages monitoring of rotary air preheater has been described. In the proposed model, the existing DCS based instrumentation system has been modified and online leakage monitoring system has been developed. This model has been installed in a captive power plant with high capacity boilers and very much satisfactory operation of this system has been observed. The observed online data along with their analysis results are presented in this paper.

  1. The Autonomous Stress Indicator for Remotely Monitoring Power System State and Watching for Potential Instability

    Directory of Open Access Journals (Sweden)

    Geza Joos

    2009-02-01

    Full Text Available The proposed Autonomous Stress Indicator (ASI is a device that monitors the contents of the protection relays on a suspect weak power system bus and generates a performance level related to the degree of system performance degradation or instability. This gives the system operators some time (minutes to take corrective action. In a given operating area there would not likely be a need for an ASI on every bus. Note that the ASI does not trip any breakers; it is an INFORMATION ONLY device. An important feature is that the system operator can subsequently interrogate the ASI to determine the factor(s that led to the performance level that has been initially annunciated, thereby leading to a course of action. This paper traces the development of the ASI which is an ongoing project. The ASI could be also described as a stress-alert device whose function is to alert the System Operator of a stressful condition at its location. The characteristics (or essential qualities of this device are autonomy, selectivity, accuracy and intelligence. These will fulfill the requirements of the recommendation of the Canada –US Task Force in the August 2003 system collapse. Preliminary tests on the IEEE 39-bus model indicate that the concept has merit and development work is in progress. While the ASI can be applied to all power system operating conditions, its principal application is to the degraded state of the system where the System Operator must act to restore the system to the secure state before it migrates to a stage of collapse. The work of ASI actually begins with the Areas of Vulnerability and ends with the Predictive Module as described in detail in this paper. An application example of a degraded system using the IEEE 39-bus system is included.

  2. RF Power Detector/Monitor Upgrade for the 500MHz Systems at the ALS

    Energy Technology Data Exchange (ETDEWEB)

    Baptiste, K.

    2003-05-08

    Several systems rely on the accurate and linear detection of 500 MHz signals, (the fundamental frequency of both the Booster Ring and Storage Ring) over a dynamic range in excess of 25dB. Prior to this upgrade, the detector/monitor was diode based and though this type of detector could handle the dynamic range requirement it could not do so in an accurate and linear manner. In order to meet the requirements (dynamic range greater than or equal to 25dB, accurate and linear to +-0.25dB over the range, and additional circuitry to interface to the legacy control system and interlocks), a new RF Power Detector/Monitor has been developed using two AD8361, Analog Devices Tru RMS Detectors and a fuzzy comparator, which extends the overall detector's range to twice that of the AD8361. Further information is available [www.analogedevices.com/]. Details of the design requirements and the detector/monitor's circuit as well as the performance of the detector will be presented.

  3. Implementation of an on-line monitoring system for transmitters in a CANDU nuclear power plant

    Science.gov (United States)

    Labbe, A.; Abdul-Nour, G.; Vaillancourt, R.; Komljenovic, D.

    2012-05-01

    Many transmitters (pressure, level and flow) are used in a nuclear power plant. It is necessary to calibrate them periodically to ensure that their measurements are accurate. These calibration tasks are time consuming and often contribute to worker radiation exposure. Human errors can also sometimes degrade their performance since the calibration involves intrusive techniques. More importantly, experience has shown that the majority of current calibration efforts are not necessary. These facts motivated the nuclear industry to develop new technologies for identifying drifting instruments. These technologies, well known as on-line monitoring (OLM) techniques, are non-intrusive and allow focusing the maintenance efforts on the instruments that really need a calibration. Although few OLM systems have been implemented in some PWR and BWR plants, these technologies are not commonly used and have not been permanently implemented in a CANDU plant. This paper presents the results of a research project that has been performed in a CANDU plant in order to validate the implementation of an OLM system. An application project, based on the ICMP algorithm developed by EPRI, has been carried out in order to evaluate the performance of an OLM system. The results demonstrated that the OLM system was able to detect the drift of an instrument in the majority of the studied cases. A feasibility study has also been completed and has demonstrated that the implementation of an OLM system at a CANDU nuclear power plant could be advantageous under certain conditions.

  4. A fence line noble gas monitoring system for nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Grasty, R.L.; Hovgaard, J.; LaMarre, J.R

    2001-07-01

    A noble gas monitoring system has been installed at Ontario Power Generations' Pickering Nuclear Generating Station (PNGS) near Toronto, Canada. This monitoring system allows a direct measure of air kerma from external radiation instead of calculating this based on plant emission data and meteorological models. This has resulted in a reduction in the reported effective dose from external radiation by a factor of at least ten. The system consists of nine self-contained units, each with a 7.6 cm x 7.6 cm (3 inch x 3 inch) NaI(Tl) detector that is calibrated for air kerma. The 512-channel gamma ray spectral information is downloaded daily from each unit to a central computer where the data are stored and processed. A spectral stripping procedure is used to remove natural background variations from the spectral windows used to monitor xenon-133 ({sup 133}Xe), xenon-135 ({sup 135}Xe), argon-41 ({sup 41}Ar), and skyshine radiation from the use of radiography sources. Typical monthly minimum detection limits in air kerma are 0.3 nGy for {sup 133}Xe, 0.7 nGy for {sup 135}Xe, 3 nGy for {sup 41}Ar and 2 nGy for skyshine radiation. Based on 9 months of continuous operation, the annualised air kerma due to {sup 133}Xe, {sup 135}Xe and {sup 41}Ar and skyshine radiation were 7 nGy, 8 nGy, 26 nGy and 107 nGy respectively. (author)

  5. Decentralized Monitoring and Control of Electric Power Distribution System with a use case of Community Energy Storage System

    Science.gov (United States)

    Huq, Kazi Mohammad Moyeenull

    This work focuses on the platform and framework required for developing decentralized monitoring and control applications for a distribution system. Decentralized control of Community Energy Storage (CES) devices has been considered as a use case. The first chapter gives an overview of energy management system and applications. Then the development of centralized and decentralized CES control applications are discussed. The next chapters discusses the software architecture of a typical centralized SCADAEMS platform and outlines the architecture required for a decentralized platform. Then, suitability of IEC 61850 standard for decentralized monitoring and control is investigated and an approach to developing decentralized applications in IEC 61850 enabled environment is proposed and demonstrated. Finally, CIM standard is reviewed for exchanging power system topology information for distributed control.

  6. On-Road Driver Monitoring System Based on a Solar-Powered In-Vehicle Embedded Platform

    Directory of Open Access Journals (Sweden)

    Yen-Lin Chen

    2014-01-01

    Full Text Available This study presents an on-road driver monitoring system, which is implemented on a stand-alone in-vehicle embedded system and driven by effective solar cells. The driver monitoring function is performed by an efficient eye detection technique. Through the driver’s eye movements captured from the camera, the attention states of the driver can be determined and any fatigue states can be avoided. This driver monitoring technique is implemented on a low-power embedded in-vehicle platform. Besides, this study also proposed monitoring machinery that can detect the brightness around the car to effectively determine whether this in-vehicle system is driven by the solar cells or by the vehicle battery. On sunny days, the in-vehicle system can be powered by solar cell in places without the vehicle battery. While in the evenings or on rainy days, the ambient solar brightness is insufficient, and the system is powered by the vehicle battery. The proposed system was tested under the conditions that the solar irradiance is 10 to 113 W/m2 and solar energy and brightness at 10 to 170. From the testing results, when the outside solar radiation is high, the brightness of the inside of the car is increased, and the eye detection accuracy can also increase as well. Therefore, this solar powered driver monitoring system can be efficiently applied to electric cars to save energy consumption and promote the driving safety.

  7. INTELLIGENT MONITORING SYSTEM WITH HIGH TEMPERATURE DISTRIBUTED FIBEROPTIC SENSOR FOR POWER PLANT COMBUSTION PROCESSES

    Energy Technology Data Exchange (ETDEWEB)

    Kwang Y. Lee; Stuart S. Yin; Andre Boheman

    2003-12-26

    The objective of the proposed work is to develop an intelligent distributed fiber optical sensor system for real-time monitoring of high temperature in a boiler furnace in power plants. Of particular interest is the estimation of spatial and temporal distributions of high temperatures within a boiler furnace, which will be essential in assessing and controlling the mechanisms that form and remove pollutants at the source, such as NOx. The basic approach in developing the proposed sensor system is three fold: (1) development of high temperature distributed fiber optical sensor capable of measuring temperatures greater than 2000 C degree with spatial resolution of less than 1 cm; (2) development of distributed parameter system (DPS) models to map the three-dimensional (3D) temperature distribution for the furnace; and (3) development of an intelligent monitoring system for real-time monitoring of the 3D boiler temperature distribution. Under Task 1, the efforts focused on developing an innovative high temperature distributed fiber optic sensor by fabricating in-fiber gratings in single crystal sapphire fibers. So far, our major accomplishments include: Successfully grown alumina cladding layers on single crystal sapphire fibers, successfully fabricated in-fiber gratings in single crystal sapphire fibers, and successfully developed a high temperature distributed fiber optic sensor. Under Task 2, the emphasis has been on putting into place a computational capability for simulation of combustors. A PC workstation was acquired with dual Xeon processors and sufficient memory to support 3-D calculations. An existing license for Fluent software was expanded to include two PC processes, where the existing license was for a Unix workstation. Under Task 3, intelligent state estimation theory is being developed which will map the set of 1D (located judiciously within a 3D environment) measurement data into a 3D temperature profile. This theory presents a semigroup

  8. GPRS在电力监控系统中的应用%Application of GPRS Technology in Power Monitoring System

    Institute of Scientific and Technical Information of China (English)

    张同良; 孙璐

    2011-01-01

    随着移动通汛技术的发展,GPRS也被应用到电力监控系统中来.本文分析了GPRS技术应用于电力监控系统的优缺点,提出了利用GPRS对电力系统进行监控的方案.%With mobile technology development, GPRS is gradually used in power system state monitoring recently. The aim of thispaper is to analyze the advantages and disadvantages of GPRS in monitoring of power system and gives a scheme.

  9. On-Road Driver Monitoring System Based on a Solar-Powered In-Vehicle Embedded Platform

    OpenAIRE

    Yen-Lin Chen; Chao-Wei Yu; Zi-Jie Chien; Chin-Hsuan Liu; Hsin-Han Chiang

    2014-01-01

    This study presents an on-road driver monitoring system, which is implemented on a stand-alone in-vehicle embedded system and driven by effective solar cells. The driver monitoring function is performed by an efficient eye detection technique. Through the driver’s eye movements captured from the camera, the attention states of the driver can be determined and any fatigue states can be avoided. This driver monitoring technique is implemented on a low-power embedded in-vehicle platform. Besides...

  10. Nanopillar Arrayed Triboelectric Nanogenerator as a Self-Powered Sensitive Sensor for a Sleep Monitoring System.

    Science.gov (United States)

    Song, Weixing; Gan, Baoheng; Jiang, Tao; Zhang, Yue; Yu, Aifang; Yuan, Hongtao; Chen, Ning; Sun, Chunwen; Wang, Zhong Lin

    2016-08-23

    A flexible and low-cost triboelectric nanogenerator (TENG) based on a patterned aluminum-plastic film and an entrapped cantilever spring leaf is developed as a self-powered sensitive triboelectric sensor for sleep-body movement monitoring. The working mechanism and the impact factors of electric output performance were systematically investigated and elaborated. Due to the patterned nanostructures of the recently designed TENG, both the output voltage and current are greatly enhanced, and thereby the sensitivity of the device is significantly improved. The self-powered and sensitive device has been demonstrated as a smart body motion sensor of sleep monitoring for diagnosis of sleep disorders due to its high sensitivity and excellent stability. This work may promote the application of self-powered TENGs for healthcare and be helpful for the development of real-time mobile healthcare services and smart external portable electronics.

  11. UHF-Band Wireless Power Transfer System for Structural Health Monitoring Sensor Network

    Directory of Open Access Journals (Sweden)

    Tansheng Li

    2013-01-01

    Full Text Available For detecting and measuring health conditions of bridges, wireless sensor networks are used in these days. However, battery life is critically restricting the application and maintenance cost of sensor network systems. To extend life time, a wireless power transfer system at UHF band is introduced to supply the current wireless sensor network. This power transfer system is based on electric wave at 950 MHz. This power transfer system is redesigned for tiny power transmission, including a combination of a rectenna and a Cockcroft-Walton boost converter, battery board, and a control board. Also, current wireless sensor network is redesigned for power transfer system. The working flow of sensor network is modified to bottom-to-top to save power of sensor modules which are the power bottleneck of this sensor system. As a result, the system is able to support a sensor module continuously with received power of −14 dBmW, when the transmitting antenna is 30 dBmW at 10 meters distance.

  12. Aerospace Systems Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Phase I STTR project will demonstrate the Aerospace System Monitor (ASM). This technology transforms the power distribution network in a spacecraft or aircraft...

  13. The design of monitoring communication system Based on Power line carrier

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>The design of the power line carrier communication system was introduced in this paper,DSP was adopted as the hardware platform to complete the core task.DSP sending terminal delivered the collecting data to the DSP receiving terminal through the power line carrier, and the DSP receiving terminal send the data to PC through a serial port.The design improved the power line carrier communication system and the data transmission became faster and more reliable.The experiment results showed that the PER of the receiving data is less than 0.4%, which satisfied the power line carrier communication requirement Our design is feasible and effective.

  14. Design and Development of Low Power Wireless Sensor System for Measurement and Monitoring of Bio-Medical Parameters

    Directory of Open Access Journals (Sweden)

    D. Vishnu Vardhan, K. Soundara Rajan, Y. Narasimha Murthy

    2013-07-01

    Full Text Available This paper presents the design and development of a low power embedded system for the measurement and monitoring of physiological parameters like body temperature, respiration, blood pressure and ECG. The design is developed around a low power microcontroller MSP430 from Texas Instruments. A wireless sensor module is used to transfer the data from microcontroller to the PC and a graphical user interface (GUI is developed to display the measured data in the graphical form.

  15. Hardware and software system for monitoring oil pump operation in power high-voltage transformers

    Directory of Open Access Journals (Sweden)

    Михайло Дмитрович Дяченко

    2017-07-01

    Full Text Available The article considers the basic prerequisites for the creation of an automated monitoring system for oil pumps of high-voltage transformers. This is due to the fact that the long operation of oil pumps results in deterioration and destruction of bearings, rubbing of the rotor, breakage and damage to the impeller, leakage, etc., which inevitably causes a significant decrease in the insulating properties of the transformer oil and leads to expenditures for its further recovery. False triggerings of gas protection sometimes occur. Continuous operation of the electric motor also requires additional equipment to protect the motor itself from various emergency situations, such as a short in the stator winding, a housing breakdown, an incomplete phase mode, etc. The use of stationary systems provides: diagnosing defects at an early stage of their development, increasing the reliability and longevity of the equipment components, increasing the overhaul period, decreasing the number of emergency stops, and adjusting the schedule of preventative maintenance. The basic principles of identification of the damaged part of the oil pump are given, the hardware and algorithmic solutions are considered in the work. The full-scale tests of the model sample on the power transformer of the high-voltage substation confirmed the assumption of the possibility of detecting the damaged unit separating it from the rest connected in one mechanical structure. A detailed analysis of the operation of each of the units is carried out by means of the general substation switchboard and displayed as graphs, diagrams and text messages. When the limit values of vibration are reached, faults in the operation of the unit are detected, the overlimit current values, a warning alarm is activated, and the command to disconnect the damaged unit is issued. The optimal solution for the organization of the information collection system using the principle of sensor networks, but combined

  16. Developing a power monitoring and protection system for the junction boxes of an experimental seafloor observatory network

    Institute of Scientific and Technical Information of China (English)

    Jun WANG; De-jun LI‡; Can-jun YANG; Zhi-feng ZHANG; Bo JIN; Yan-hu CHEN

    2015-01-01

    A power monitoring and protection system based on an embedded processor was designed for the junction boxes (JBs) of an experimental seafloor observatory network in China. The system exhibits high reliability, fast response, and high real-time performance. A two-step power management method which uses metal-oxide-semiconductor field-effect transistors (MOSFETs) and a mechanical contactor in series was adopted to generate a reliable power switch, to limit surge currents and to facilitate automatic protection. Grounding fault diagnosis and environmental monitoring were conducted by designing a ground-ing fault detection circuit and by using selected sensors, respectively. The data collected from the JBs must be time-stamped for analysis and for correlation with other events and data. A highly precise system time, which is necessary for synchronizing the times within and across nodes, was generated through the IEEE 1588 (precision clock synchronization protocol for networked measurement and control systems) time synchronization method. In this method, time packets were exchanged between the grandmaster clock at the shore station and the slave clock module of the system. All the sections were verified individually in the laboratory prior to a sea trial. Finally, a subsystem for power monitoring and protection was integrated into the complete node system, installed in a frame, and deployed in the South China Sea. Results of the laboratory and sea trial experiments demonstrated that the developed system was effective, stable, reliable, and suitable for continuous deep-sea operation.

  17. Demonstration of Photovoltaic-Powered Cathodic Protection System with Remote Monitoring Capability

    Science.gov (United States)

    2014-02-01

    improved photovoltaic (PV) power systems with integrated battery backup, solar energy has become a viable alternative where grid power is not available...such as night time and during overcast weather. In combi- nation with solar panels , each water tank had a dedicated set of storage batteries and an...1 kW/m2. Three PV solar array modules were wired in parallel to comprise a single solar panel . On average, each solar panel supplies power to one

  18. Power system

    Science.gov (United States)

    Hickam, Christopher Dale

    2008-03-18

    A power system includes a prime mover, a transmission, and a fluid coupler having a selectively engageable lockup clutch. The fluid coupler may be drivingly connected between the prime mover and the transmission. Additionally, the power system may include a motor/generator drivingly connected to at least one of the prime mover and the transmission. The power-system may also include power-system controls configured to execute a control method. The control method may include selecting one of a plurality of modes of operation of the power system. Additionally, the control method may include controlling the operating state of the lockup clutch dependent upon the mode of operation selected. The control method may also include controlling the operating state of the motor/generator dependent upon the mode of operation selected.

  19. An interation of lifetime monitoring of steam generators in power control systems; Integration der Lebensdauerueberwachung von Dampferzeugern in die Kraftwerksleittechnik

    Energy Technology Data Exchange (ETDEWEB)

    Kunze, Ulrich; Pels Leusden, Christoph; Spinner, Ralf [Siemens AG, Erlangen (Germany). Energy Sector; Hackstein, Holger [Siemens AG, Offenbach am Main (Germany). Energy Sector; Walz, Horst [Siemens AG, Karlsruhe (Germany). Energy Sector

    2008-07-01

    The substantial cost-relevant requirements of the operation of power stations are a highly flexible operation, efficient maintenance, a high efficiency and a high availability. Computer-assisted procedures are indispensable for the continuous monitoring of lifetime consumption and for the condition-dependent maintenance of the boiler. The fatigue monitoring system (FMS) offers all possibilities of the control system. The authors of the contribution under consideration report on an integration of life time monitoring of steam generators into the power station control technology. The technical fundamentals for the computation of the boiler lifetime as well as the fundamentals of integration philosophy and their conversion are presented. Subsequently, a configuration exemplarily is presented, and its results are described.

  20. A low-power and miniaturized electrocardiograph data collection system with smart textile electrodes for monitoring of cardiac function.

    Science.gov (United States)

    Dai, Ming; Xiao, Xueliang; Chen, Xin; Lin, Haoming; Wu, Wanqing; Chen, Siping

    2016-12-01

    With the increasing aging population as well as health concerns, chronic heart disease has become the focus of public attention. A comfortable, low-powered, and wearable electrocardiogram (ECG) system for continuously monitoring the elderly's ECG signals over several hours is important for preventing cardiovascular diseases. Traditional ECG monitoring apparatus is often inconvenient to carry, has many electrodes to attach to the chest, and has a high-power consumption. There is also a challenge to design an electrocardiograph that satisfies requirements such as comfort, confinement, and compactness. Based on these considerations, this study presents a biosensor acquisition system for wearable, ubiquitous healthcare applications using three textile electrodes and a recording circuit specialized for ECG monitoring. In addition, several methods were adopted to reduce the power consumption of the device. The proposed system is composed of three parts: (1) an ECG analog front end (AFE), (2) digital signal processing and micro-control circuits, and (3) system software. Digital filter methods were used to eliminate the baseline wander, skin contact noise, and other interfering signals. A comparative study was conducted using this system to observe its performance with two commercial Holter monitors. The experimental results demonstrated that the total power consumption of this proposed system in a full round of ECG acquisition was only 29.74 mW. In addition, this low-power system performed well and stably measured the heart rate with an accuracy of 98.55 %. It can also contain a real-time dynamic display with organic light-emitting diodes (OLED) and wirelessly transmit information via a Bluetooth 4.0 module.

  1. A Study on the Development and Application of Monitoring System for Power Transmission Facilities by using the Optical Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Lee, K.J.; Cho, H.K.; Han, M.S.; Kim, S.K.; Oh, M.T; Park, K.J.; Kim, W.K. [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center; Park, H.K.; Kim, N.; Ban, J.K.; Song, W.Y.; Park, S.K.; Lee, S.Y.; Lee, K.Y.; Lee, Y.H.; Yoon, J.H.; Kim, S.T. [Electrical Engineering and Science Research Center (Korea, Republic of)

    1993-12-31

    Corresponding to extended scope of transmission line maintenance and surveillance system, complex and long transmission line, high capacity and diversutt of monitoring information owing to bulky and high voltage of the system, there have been great demands for new measurement and communication technology on maintenance and monitoring of transmission line facilities. Henceforth in the field of large scale communication system, to overcome shortcomings that former electrical communication has, the introduction of optical communication system is actively being carried out and especially for transmission of power information such as protection, monitoring and control of electric power system operation, optical fiber composite overhead ground wire(OPGW) is increasingly built in the field. Accordingly, from formerly installed optical fibers in OPGW, by utilizing fiber`s low loss, wide bandwidth, high dielectric properties, system information for maintenance, i.e. fault information, weather information, etc. are directly sent to the maintenance department. This promotion in modernization of power transmission line maintenance will set up basis for the realization of effective management, automatic control and remote sensing in maintenance tasks. Eventually, this system can provides various information such as wind velocity and direction, state of aircraft warning lamp and fault current information ground wire etc.. (author). 38 refs., figs.

  2. Performance monitoring algorithm for optimizing electrical power generated by using photovoltaic system

    Science.gov (United States)

    Pradeep, M. V. K.; Balbir, S. M. S.; Norani, M. M.

    2016-11-01

    Demand for electricity in Malaysia has seen a substantial hike in light of the nation's rapid economic development. The current method of generating electricity is through the combustion of fossil fuels which has led to the detrimental effects on the environment besides causing social and economic outbreaks due to its highly volatile prices. Thus the need for a sustainable energy source is paramount and one that is quickly gaining acceptance is solar energy. However, due to the various environmental and geographical factors that affect the generation of solar electricity, the capability of solar electricity generating system (SEGS) is unable to compete with the high conversion efficiencies of conventional energy sources. In order to effectively monitor SEGS, this study is proposing a performance monitoring system that is capable of detecting drops in the system's performance for parallel networks through a diagnostic mechanism. The performance monitoring system consists of microcontroller connected to relevant sensors for data acquisition. The acquired data is transferred to a microcomputer for software based monitoring and analysis. In order to enhance the interception of sunlight by the SEGS, a sensor based sun tracking system is interfaced to the same controller to allow the PV to maneuver itself autonomously to an angle of maximum sunlight exposure.

  3. Monitoring of the electrical parameters in off-grid solar power system

    Science.gov (United States)

    Idzkowski, Adam; Leoniuk, Katarzyna; Walendziuk, Wojciech

    2016-09-01

    The aim of this work was to make a monitoring dedicated to an off-grid installation. A laboratory set, which was built for that purpose, was equipped with a PV panel, a battery, a charge controller and a load. Additionally, to monitor electrical parameters from this installation there were used: LabJack module (data acquisition card), measuring module (self-built) and a computer with a program, which allows to measure and present the off-grid installation parameters. The program was made in G language using LabVIEW software. The designed system enables analyzing the currents and voltages of PV panel, battery and load. It makes also possible to visualize them on charts and to make reports from registered data. The monitoring system was also verified by a laboratory test and in real conditions. The results of this verification are also presented.

  4. Development of elements of the condition monitoring system of turbo generators of thermal power stations and nuclear power plants

    Science.gov (United States)

    Kumenko, A. I.; Kostyukov, V. N.; Kuz'minykh, N. Yu.; Boichenko, S. N.; Timin, A. V.

    2017-08-01

    The rationale is given for the improvement of the regulatory framework for the use of shaft sensors for the in-service condition monitoring of turbo generators and the development of control systems of shaft surfacing and misalignments of supports. A modern concept and a set of methods are proposed for the condition monitoring of the "shaft line-thrust bearing oil film-turbo generator supports" system elements based on the domestic COMPACS® technology. The system raw data are design, technology, installation, and operating parameters of the turbo generator as well as measured parameters of the absolute vibration of supports and mechanical quantities, relative displacements and relative vibration of the rotor teeth in accordance with GOST R 55263-2012. The precalculated shaft line assembly line in the cold state, the nominal parameters of rotor teeth positions on the dynamic equilibrium curve, the static and dynamic characteristics of the oil film of thrust bearings, and the shaft line stiffness matrix of unit support displacements have been introduced into the system. Using the COMPACS-T system, it is planned to measure positions and oscillations of rotor teeth, to count corresponding static and dynamic characteristics of the oil film, and the static and dynamic loads in the supports in real time. Using the obtained data, the system must determine the misalignments of supports and corrective alignments of rotors of coupling halves, voltages in rotor teeth, welds, and bolts of the coupling halves, and provide automatic conclusion if condition monitoring parameters correspond to standard values. A part of the methodological support for the proposed system is presented, including methods for determining static reactions of supports under load, the method for determining shaft line stiffness matrices, and the method for solving the inverse problem, i.e., the determination of the misalignments of the supports by measurements of rotor teeth relative positions in bearing

  5. Automatic Distance Monitoring System of Contact Connections in High Voltage Equipment of Electric Power Lines

    Directory of Open Access Journals (Sweden)

    M. Diachenko

    2013-01-01

    Full Text Available The developed automatic distance monitoring system of contact connections in high voltage equipment is based on technology of sensor circuits. The paper shows application of control methodology for contact connections in accordance with time rate of conductor temperature changes and contact connection and also direct measurement of transient resistance.

  6. Development of a web-based monitoring system using operation parameters for the main component in nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Son, Dong Chan; An, Kung Il; Hong, Suk Young; Lee, Jeong Soo; Jung, Duk Jin; Shin, Sun Hee; Son, So Hee [Daesang Information Technology Co., Ltd., Seoul (Korea, Republic of)

    2004-02-15

    The frequency of the damage is increasing, which is caused by the fatigue, according to the increase of running of nuclear power plants. So we need to acquire the reliance of design data to estimate the fatigue and damage of major machinery that might happen as time-dependent crack growth characterization. The research is focused on keeping operating record of nuclear power plants about major machinery which consists of a nuclear reactor pressure boarder on each excessive operating condition including normal operating and extraordinary operating by estimating fracture mechanical movements on real time and fatigue about major nuclear power plants machinery, which are acquired the pressure and temperature data. For further details about the scope and contents of R and D are following. Development of H/W that is necessary to acquire operating real time data of heating and hydraulic power. Selection of a safety variable about major system by each type (the four NPP, all unit). Communication protocol development for connecting between CARE system data base server and fatigue monitoring system data base server. Development of connecting database for controlling and storing of heating and hydraulic power operating data. Real time monitoring system development based on Web using JAVA.

  7. Application of Devices and Systems Designed for Power Quality Monitoring and Assessment

    Directory of Open Access Journals (Sweden)

    Wiesław Gil

    2014-03-01

    Full Text Available The paper presents the problems associated with increasing demands on the equipment and systems for power quality assessment (PQ, installed at power substations. Difficulties are signaled due to current lack of standards defining the test methodology of measuring devices. The necessary device properties and the structure of a large system operated in real time and designed to assess the PQ are discussed. The usefulness of multi-channel analyzers featuring the identification and registration of transients is pointed out. The desirability of synchrophasor assessment implementation and device integration by standard PN-EN 61850 with other SAS devices is also justified.

  8. Condition monitoring of rotor blades of wind power systems; Zustandsueberwachung von Rotorblaettern an Windenergieanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Frankenstein, B.; Froehlich, K.J.; Lieske, U.; Schuber, L. [Fraunhofer Institut Zerstoerungsfreie Pruefverfahren (IZFP), Institutsteil Dresden (Germany)

    2007-07-01

    The Fraunhofer Institute of Non-Destructive Testing Dresden (IzfP-D) uses condition monitoring systems, which by permanent monitoring e.g. of wind rotors, aircraft components, or pipelines are to ensure high availability of the object. This way, damage (e.g. crack initiation and propagation, delamination) can be detected early, and early repair measures will lengthen the life of the components and reduce standstill times during repair. Guided elastic waves are used for wind rotor monitoring, which are induced by piezo fibre converters. The contribution describes the method and measuring instrumentation for generation and detection of acoustic waves in composite materials. The focus is on static load tests of rotor blades, of which the status and trends are presented. (orig.)

  9. Design of a video capsule endoscopy system with low-power ASIC for monitoring gastrointestinal tract.

    Science.gov (United States)

    Liu, Gang; Yan, Guozheng; Zhu, Bingquan; Lu, Li

    2016-11-01

    In recent years, wireless capsule endoscopy (WCE) has been a state-of-the-art tool to examine disorders of the human gastrointestinal tract painlessly. However, system miniaturization, enhancement of the image-data transfer rate and power consumption reduction for the capsule are still key challenges. In this paper, a video capsule endoscopy system with a low-power controlling and processing application-specific integrated circuit (ASIC) is designed and fabricated. In the design, these challenges are resolved by employing a microimage sensor, a novel radio frequency transmitter with an on-off keying modulation rate of 20 Mbps, and an ASIC structure that includes a clock management module, a power-efficient image compression module and a power management unit. An ASIC-based prototype capsule, which measures Φ11 mm × 25 mm, has been developed here. Test results show that the designed ASIC consumes much less power than most of the other WCE systems and that its total power consumption per frame is the least. The image compression module can realize high near-lossless compression rate (3.69) and high image quality (46.2 dB). The proposed system supports multi-spectral imaging, including white light imaging and autofluorescence imaging, at a maximum frame rate of 24 fps and with a resolution of 400 × 400. Tests and in vivo trials in pigs have proved the feasibility of the entire system, but further improvements in capsule control and compression performance inside the ASIC are needed in the future.

  10. The rectenna design on contact lens for wireless powering of the active intraocular pressure monitoring system.

    Science.gov (United States)

    Cheng, H W; Jeng, B M; Chen, C Y; Huang, H Y; Chiou, J C; Luo, C H

    2013-01-01

    This paper proposed a wireless power harvesting system with micro-electro-mechanical-systems (MEMS) fabrication for noninvasive intraocular pressure (IOP) measurement on soft contact lens substructure. The power harvesting IC consists of a loop antenna, an impedance matching network and a rectifier. The proposed IC has been designed and fabricated by CMOS 0.18 um process that operates at the ISM band of 5.8 GHz. The antenna and the power harvesting IC would be bonded together by using flip chip bonding technologies without extra wire interference. The circuit utilized an impedance transformation circuit to boost the input RF signal that improves the circuit performance. The proposed design achieves an RF-to-DC conversion efficiency of 35% at 5.8 GHz.

  11. Condition monitoring of rotor blades of modern wind power systems; Ueberwachung mit Hertz. Condition Monitoring von Rotorblaettern moderner Windenergieanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Fecht, Nikolaus

    2010-06-15

    With seven wind turbines, the Austrian wind farm ''Sternwald'' is the biggest wind farm in Upper Austria. It is the only wind farm in a forest, and all turbines are therefore equipped with automatic fire fighting equipment. The mountain range on which the wind farm is located is about 1000 m high, with strong wind and much ice and snow in the winter season. For this reason, the owner decided to instal a condition monitoring system with ice detectors. The piezoelectric sensors are mounted directly on the rotor blades as measurements on the nacelle will always be incorrect. Installation on the rotor blades, on the other hand, makes high demands on the fastenings and sensors as the velocity of the blade tips may be up to 250 km per hour. (orig.)

  12. Battery monitoring in Mexican hybrid power systems; Monitoreo de las baterias en sistemas de potencia hibridos Mexicanos

    Energy Technology Data Exchange (ETDEWEB)

    Flores, J. Roberto; Agredano, Jaime [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1997-12-31

    Hybrid power systems for an autonomous power supply are based on different renewable and fossil energy sources. They are considered as a good option for the power supply of remote areas. In these systems an energy storage is a vital necessity and very often this storage will consist of batteries which are generally connected in series and parallel arrays, or both. In Mexico as in other countries, the most extensively use batteries used for this application are the stationary and electric car type deep cycle batteries. However the experience with them in these systems is generally not very good. One way to overcome this problem is to maintain a regular monitoring of installing monitoring equipment, in order to make preventive actions before a developing fault can have serious consequences and in this manner increase the practical lifetime of the batteries. Unfortunately, battery monitoring is not easy task because most of the hybrid power systems are installed in remote areas which makes it difficult and expensive. In Mexico it has been not possible to maintain a regular monitoring of all hybrid power systems installed, due to the high cost of this work and the lack of founds. The hybrid power systems installed in the state of Quintana Roo are the only systems that have been continuously monitored since their installation. This paper gives an overview of the hybrid power systems installed in Mexico, focusing in the battery banks, the way they are being monitored, the main parameters used to detect possible premature problems and the method used to evaluate the battery bank conditions. Finally some results from the battery banks monitoring activities are presented. [Espanol] Los sistemas de potencia hibridos para un suministro autonomo de energia a regiones remotas, estan basados en diferentes fuentes de energia fosiles y renovables. Estos son considerados como una buena opcion para el suministro de energia a areas remotas. En estos sistemas es una necesidad vital el

  13. Highly Efficient Wireless Powering for Autonomous Structural Health Monitoring and Test/Evaluation Systems

    Science.gov (United States)

    2016-07-27

    teaching and mentorship, research and service. Received Book TOTAL: Received Book Chapter TOTAL: PERCENT_SUPPORTEDNAME FTE Equivalent: Total Number...in SC as an Electrophysics Engineer c. Alain Anton accepted a summer Internship at MIT Lincoln Laboratory and will puruse...e. Meilyn Planas joined Florida Power and Light as an IT System Administrator 3. This project has enhanced the teaching training of one Ph.D

  14. Safety system status monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, J.R.; Morgenstern, M.H.; Rideout, T.H.; Cowley, P.J.

    1984-03-01

    The Pacific Northwest Laboratory has studied the safety aspects of monitoring the preoperational status of safety systems in nuclear power plants. The goals of the study were to assess for the NRC the effectiveness of current monitoring systems and procedures, to develop near-term guidelines for reducing human errors associated with monitoring safety system status, and to recommend a regulatory position on this issue. A review of safety system status monitoring practices indicated that current systems and procedures do not adequately aid control room operators in monitoring safety system status. This is true even of some systems and procedures installed to meet existing regulatory guidelines (Regulatory Guide 1.47). In consequence, this report suggests acceptance criteria for meeting the functional requirements of an adequate system for monitoring safety system status. Also suggested are near-term guidelines that could reduce the likelihood of human errors in specific, high-priority status monitoring tasks. It is recommended that (1) Regulatory Guide 1.47 be revised to address these acceptance criteria, and (2) the revised Regulatory Guide 1.47 be applied to all plants, including those built since the issuance of the original Regulatory Guide.

  15. Development of nuclear power plant online monitoring system using statistical quality control

    Energy Technology Data Exchange (ETDEWEB)

    An, Sang Ha

    2006-02-15

    Statistical Quality Control techniques have been applied to many aspects of industrial engineering. An application to nuclear power plant maintenance and control is also presented that can greatly improve plant safety. As a demonstration of such an approach, a specific system is analyzed: the reactor coolant pumps (RCP) and the fouling resistance of heat exchanger. This research uses Shewart X-bar, R charts, Cumulative Sum charts (CUSUM), and Sequential Probability Ratio Test (SPRT) to analyze the process for the state of statistical control. And we made Control Chart Analyzer (CCA) to support these analyses that can make a decision of error in process. The analysis shows that statistical process control methods can be applied as an early warning system capable of identifying significant equipment problems well in advance of traditional control room alarm indicators. Such a system would provide operators with enough time to respond to possible emergency situations and thus improve plant safety and reliability.

  16. Power system state estimation

    CERN Document Server

    Ahmad, Mukhtar

    2012-01-01

    State estimation is one of the most important functions in power system operation and control. This area is concerned with the overall monitoring, control, and contingency evaluation of power systems. It is mainly aimed at providing a reliable estimate of system voltages. State estimator information flows to control centers, where critical decisions are made concerning power system design and operations. This valuable resource provides thorough coverage of this area, helping professionals overcome challenges involving system quality, reliability, security, stability, and economy.Engineers are

  17. Condition Monitoring with WinTControl {sup trademark} in variable-speed wind power systems; Condition Monitoring mit WinTControl {sup trademark} an drehzahlveraenderlichen Windenergieanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Becker; Dahlhaus, N. [Flender Service GmbH, Herne (Germany). Abt. Condition Monitoring

    2003-07-01

    In 2002, German insurance company had to pay the all-time high of about 40 million Euro for damage in wind power systems. In consequence, a servicing and maintenance clause is now included in the insurance contracts, and requirements on condition monitoring for wind power systems were defined. Condition monitoring is based on an analysis of vibrations of components that are subject to wear, i.e. gears, generators, toothing, roller bearings, rotors, and electric components. All of these have typical and significant vibration patterns which can be measured and compared in order to assess the status of a plant by high-sensitivity spectral analyses. The contribution presents the examples of reversible, constant-speed asynchronous generators with gears and of double-fed, variable-speed asynchronous generators with gears. (orig.) [German] Im Jahre 2002 haben die deutschen Versicherer fuer Schaeden an Windenergieanlagen (WEA) den Spitzenwert von rund 40 Mio. Euro bezahlt, was unter anderem dazu fuehrte, dass eine Wartungs- und Instandhaltungsklausel in die Vertraege aufgenommen und Anforderungen an ein geeignetes Condition Monitoring fuer Windenergieanlagen definiert wurden. Basis des Condition Monitoring sind 'Soll/Ist-Vergleiche' des Schwingungsverhaltens verschleissbehafteter Komponenten. Getriebe, Generatoren, Verzahnungen, Waelzlager, Rotoren und E-Technikkomponenten haben typische und signifikante Schwingungsbilder, welche bei Messung unter vergleichbaren Betriebsbedingungen eine einfache Beurteilung der Zustandveraenderung erlauben. Zustandsveraenderungen dieser Komponenten lassen sich ueber Spektralanalysen hochempfindlich verfolgen. Wie sich das Condition Monitoring an WEA dennoch realisieren laesst, wird nachfolgend an Triebstraengen mit polumschaltbaren, drehzahlstarren Asynchrongeneratoren mit Getrieben und an doppeltgespeisten, drehzahlveraenderlichen Asynchrongeneratoren mit Getrieben beschrieben. (orig.)

  18. Bushfire Disaster Monitoring System Using Low Power Wide Area Networks (LPWAN

    Directory of Open Access Journals (Sweden)

    James Jin Kang

    2017-10-01

    Full Text Available Some applications, including disaster monitoring and recovery networks, use low-power wide-area networks (LPWAN. LPWAN sensors capture data bits and transmit them to public carrier networks (e.g., cellular networks via dedicated gateways. One of the challenges encountered in disaster management scenarios revolves around the carry/forward sensed data and geographical location information dissemination to the disaster relief operatives (disaster relief agency; DRA to identify, characterise, and prioritise the affected areas. There are network topology options to reach its destination, including cellular, circuit switched, and peer-to-peer networks. In the context of natural disaster prediction, it is vital to access geographical location data as well as the timestamp. This paper proposes the usage of Pseudo A Number (PAN, that is, the calling party address, which is used by every network to include the location information instead of the actual calling party address of the gateway in LPWAN. This PAN information can be further analysed by the DRA to identify the affected areas and predict the complications of the disaster impacts in addition to the past history of damages. This paper aims to propose a solution that can predict disaster proceedings based on propagation and the velocity of impact using vector calculation of the location data and the timestamp, which are transmitted by sensors through the PAN of the gateway in LPWAN.

  19. An integrated tool and improved performance metrics to monitor the adequacy of the North American electric power system

    Science.gov (United States)

    Bilke, Terry

    The reliability of the electric power system, defined as the degree of performance of the grid according to accepted standards, is composed of two components: (1) Security: The ability of the electric system to withstand sudden disturbances such as electric short circuits or unanticipated loss of system elements. (2) Adequacy: The ability of the electric system to supply the aggregate electrical demand and energy requirements of the customers at all times, taking into account scheduled and reasonably expected unscheduled outages of system elements. There is evidence that the performance of the adequacy component of reliability is declining in North America. This research presents an improved set of metrics and a tool that supports an adequacy-monitoring model designed to track performance and identify underlying problems that impact reliability.

  20. Overview of condition monitoring and operation control of electric power conversion systems in direct-drive wind turbines under faults

    Science.gov (United States)

    Huang, Shoudao; Wu, Xuan; Liu, Xiao; Gao, Jian; He, Yunze

    2017-09-01

    Electric power conversion system (EPCS), which consists of a generator and power converter, is one of the most important subsystems in a direct-drive wind turbine (DD-WT). However, this component accounts for the most failures (approximately 60% of the total number) in the entire DD-WT system according to statistical data. To improve the reliability of EPCSs and reduce the operation and maintenance cost of DD-WTs, numerous researchers have studied condition monitoring (CM) and fault diagnostics (FD). Numerous CM and FD techniques, which have respective advantages and disadvantages, have emerged. This paper provides an overview of the CM, FD, and operation control of EPCSs in DD-WTs under faults. After introducing the functional principle and structure of EPCS, this survey discusses the common failures in wind generators and power converters; briefly reviewed CM and FD methods and operation control of these generators and power converters under faults; and discussed the grid voltage faults related to EPCSs in DD-WTs. These theories and their related technical concepts are systematically discussed. Finally, predicted development trends are presented. The paper provides a valuable reference for developing service quality evaluation methods and fault operation control systems to achieve high-performance and high-intelligence DD-WTs.

  1. Low-power wireless micromanometer system for acute and chronic bladder-pressure monitoring.

    Science.gov (United States)

    Majerus, Steve J A; Fletter, Paul C; Damaser, Margot S; Garverick, Steven L

    2011-03-01

    This letter describes the design, fabrication, and testing of a wireless bladder-pressure-sensing system for chronic, point-of-care applications, such as urodynamics or closed-loop neuromodulation. The system consists of a miniature implantable device and an external RF receiver and wireless battery charger. The implant is small enough to be cystoscopically implanted within the bladder wall, where it is securely held and shielded from the urine stream. The implant consists of a custom application-specific integrated circuit (ASIC), a pressure transducer, a rechargeable battery, and wireless telemetry and recharging antennas. The ASIC includes instrumentation, wireless transmission, and power-management circuitry, and on an average draws less than 9 μA from the 3.6-V battery. The battery charge can be wirelessly replenished with daily 6-h recharge periods that can occur during the periods of sleep. Acute in vivo evaluation of the pressure-sensing system in canine models has demonstrated that the system can accurately capture lumen pressure from a submucosal implant location.

  2. A METHOD OF COMPLEX AUTOMATED MONITORING OF UKRAINIAN POWER ENERGY SYSTEM OBJECTS TO INCREASE ITS OPERATION SAFETY

    Directory of Open Access Journals (Sweden)

    Ye.I. Sokol

    2016-05-01

    Full Text Available The paper describes an algorithm of the complex automated monitoring of Ukraine’s power energy system, aimed at ensuring safety of its personnel and equipment. This monitoring involves usage of unmanned aerial vehicles (UAVs for planned and unplanned registration status of power transmission lines (PTL and high-voltage substations (HVS. It is assumed that unscheduled overflights will be made in emergency situations on power lines. With the help of the UAV, pictures of transmission and HVS will be recorded from the air in the optical and infrared ranges, as well as strength of electric (EF and magnetic (MF fields will be measured along the route of flight. Usage specially developed software allows to compare the recorded pictures with pre-UAV etalon patterns corresponding to normal operation of investigated transmission lines and the HVSs. Such reference pattern together with the experimentally obtained maps of HVS’s protective grounding will be summarized in a single document – a passport of HVS and PTL. This passport must also contain the measured and calculated values of strength levels of EF and MF in the places where staff of power facilities stay as well as layout of equipment, the most vulnerable to the effects of electromagnetic interference. If necessary, as part of ongoing monitoring, recommendations will be given on the design and location of electromagnetic screens, reducing the levels of electromagnetic interference as well as on location of lightning rods, reducing probability lightning attachment to the objects. The paper presents analytic expressions, which formed the basis of the developed software for calculation of the EF strength in the vicinity of power lines. This software will be used as a base at UAV navigation along the transmission lines, as well as to detect violations in the transmission lines operation. Comparison of distributions of EF strength calculated with the help of the elaborated software with the known

  3. Automatic data processing and analysis system for monitoring region around a planned nuclear power plant

    Science.gov (United States)

    Kortström, Jari; Tiira, Timo; Kaisko, Outi

    2016-03-01

    The Institute of Seismology of University of Helsinki is building a new local seismic network, called OBF network, around planned nuclear power plant in Northern Ostrobothnia, Finland. The network will consist of nine new stations and one existing station. The network should be dense enough to provide azimuthal coverage better than 180° and automatic detection capability down to ML -0.1 within a radius of 25 km from the site.The network construction work began in 2012 and the first four stations started operation at the end of May 2013. We applied an automatic seismic signal detection and event location system to a network of 13 stations consisting of the four new stations and the nearest stations of Finnish and Swedish national seismic networks. Between the end of May and December 2013 the network detected 214 events inside the predefined area of 50 km radius surrounding the planned nuclear power plant site. Of those detections, 120 were identified as spurious events. A total of 74 events were associated with known quarries and mining areas. The average location error, calculated as a difference between the announced location from environment authorities and companies and the automatic location, was 2.9 km. During the same time period eight earthquakes between magnitude range 0.1-1.0 occurred within the area. Of these seven could be automatically detected. The results from the phase 1 stations of the OBF network indicates that the planned network can achieve its goals.

  4. Wearable Health Monitoring Systems

    Science.gov (United States)

    Bell, John

    2015-01-01

    The shrinking size and weight of electronic circuitry has given rise to a new generation of smart clothing that enables biological data to be measured and transmitted. As the variation in the number and type of deployable devices and sensors increases, technology must allow their seamless integration so they can be electrically powered, operated, and recharged over a digital pathway. Nyx Illuminated Clothing Company has developed a lightweight health monitoring system that integrates medical sensors, electrodes, electrical connections, circuits, and a power supply into a single wearable assembly. The system is comfortable, bendable in three dimensions, durable, waterproof, and washable. The innovation will allow astronaut health monitoring in a variety of real-time scenarios, with data stored in digital memory for later use in a medical database. Potential commercial uses are numerous, as the technology enables medical personnel to noninvasively monitor patient vital signs in a multitude of health care settings and applications.

  5. Considerations on fatigue stress range calculations in nuclear power plants using on-line monitoring systems and the ASME Code

    Energy Technology Data Exchange (ETDEWEB)

    Cicero, R., E-mail: ciceror@unican.e [INESCO INGENIEROS S.L., Santander (Spain); Departamento de Ciencia e Ingenieria del Terreno y los Materiales, Universidad de Cantabria, Santander (Spain); Cicero, S. [Departamento de Ciencia e Ingenieria del Terreno y los Materiales, Universidad de Cantabria, Santander (Spain); Gorrochategui, I. [Centro Tecnologico de Componentes, Santander (Spain); Lacalle, R. [INESCO INGENIEROS S.L., Santander (Spain); Departamento de Ciencia e Ingenieria del Terreno y los Materiales, Universidad de Cantabria, Santander (Spain)

    2010-01-15

    Nuclear power plants are generally designed and inspected according to the ASME Code. This code indicates stress intensity (S{sub INT}) as the parameter to be used in the stress analysis of components. One of the particularities of S{sub INT} is that it always takes positive values, independently of the nature of the stress (tensile or compressive). This circumstance is relevant in the Fatigue Monitoring Systems used in nuclear power plants, due to the manner in which the different variable stresses are combined in order to obtain the final total stress range. This paper describes some situations derived from the application of the ASME Code, shows different ways of dealing with them and illustrates their influence on the evaluation of the fatigue usage factor through a case study.

  6. Inspection and Monitoring Techniques for Power Lines

    Institute of Scientific and Technical Information of China (English)

    DAI Kaoshan; CHEN Shenen

    2011-01-01

    Structural assessment is prerequisite for proper maintenance of civil infrastructure.In the begining of this paper, modern inspection and monitoring methods are briefly reviewed.Experiences in applying imagebased methods for highway bridge inspection are described shortly afterward.Studies are then extended to explore technologies for power delivery infrastructure evaluation.Typical power line components are first introduced.Structural analyses show complicated coupling phenomena in the power line system; and its vulnerability is intensified by extreme environment or human induced events.As a main interest, the state-of-art of power line inspection is summarized.Both visual observations and inspections assisted with novel techniques are presented.Real time monitoring of the power line is also investigated in this paper.Technologies that have potentials for monitoring power cables, insulators, and support structures are identified.A conceptual integrated design is proposed by the authors through combining innovative inspection with promising monitoring methods to ensure a sustainable, smart power line.

  7. Development of An On-Line, Core Power Distribution Monitoring System

    Energy Technology Data Exchange (ETDEWEB)

    Tunc ALdemir; Don Miller; Peng Wang

    2007-10-02

    The objective of the proposed work was to develop a software package that can construct in three-dimensional core power distributions using the signals from constant temperature power sensors distributed in the reactor core. The software developed uses a mode-based state/parameter estmation technique that is particularly attractive when there are model uncertainties and/or large signal noise. The software yields the expected value of local power at the detector locations and points in between, as well as the probability distribution of the local power density

  8. Description of real-time Ada software implementation of a power system monitor for the Space Station Freedom PMAD DC testbed

    Science.gov (United States)

    Ludwig, Kimberly; Mackin, Michael; Wright, Theodore

    1991-01-01

    The authors describe the Ada language software developed to perform the electrical power system monitoring functions for the NASA Lewis Research Center's Power Management and Distribution (PMAD) DC testbed. The results of the effort to implement this monitor are presented. The PMAD DC testbed is a reduced-scale prototype of the electric power system to be used in Space Station Freedom. The power is controlled by smart switches known as power control components (or switchgear). The power control components are currently coordinated by five Compaq 386/20e computers connected through an 802.4 local area network. The power system monitor algorithm comprises several functions, including periodic data acquisition, data smoothing, system performance analysis, and status reporting. Data are collected from the switchgear sensors every 100 ms, then passed through a 2-Hz digital filter. System performance analysis includes power interruption and overcurrent detection. The system monitor required a hardware timer interrupt to activate the data acquisition function. The execution time of the code was optimized by using an assembly language routine. The routine allows direct vectoring of the processor to Ada language procedures that perform periodic control activities.

  9. Export Control Guide: Loose Parts Monitoring Systems for Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Langenberg, Donald W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2012-12-01

    This report describes a typical LPMS, emphasizing its application to the RCS of a modern NPP. The report also examines the versatility of AE monitoring technology by describing several nuclear applications other than loose parts monitoring, as well as some non-nuclear applications. In addition, LPMS implementation requirements are outlined, and LPMS suppliers are identified. Finally, U.S. export controls applicable to LPMSs are discussed.

  10. Moisture Migration in an Oil-Paper Insulation System in Relation to Online Partial Discharge Monitoring of Power Transformers

    Directory of Open Access Journals (Sweden)

    Wojciech Sikorski

    2016-12-01

    Full Text Available Most power transformers operating in a power system possess oil-paper insulation. A serious defect of this type of insulation, which is associated with long operation time, is an increase in the moisture content. Moisture introduces a number of threats to proper operation of the transformer, e.g., ignition of partial discharges (PDs. Due to the varying temperature of the insulation system during the unit’s normal operation, a dynamic change (migration of water takes place, precipitating the oil-paper system from a state of hydrodynamic equilibrium. This causes the PDs to be variable in time, and they may intensify or extinguish. Studies on model objects have been conducted to determine the conditions (temperature, humidity, time that will have an impact on the ignition and intensity of the observed phenomenon of PDs. The conclusions of this study will have a practical application in the evaluation of measurements conducted in the field, especially in relation to the registration of an online PD monitoring system.

  11. Stockholm Power Tech. Power systems

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    The proceedings from this symposium is presented in six volumes: Invited speakers` sessions; Power systems; Power electronics; High-voltage technology; Electrical machines and drives; and Information and control systems. This report covers the power systems volume. Separate abstracts have been prepared for 141 of the 145 papers in this volume

  12. A Real-time Video Monitoring System of Mobile Terminals Based on Android Platform: A Case Study of Electric Power Systems

    Directory of Open Access Journals (Sweden)

    Songchun Gong

    2013-03-01

    Full Text Available With the constant improvement of electrical equipment automation level, unattended electric power system node becomes increasingly popular. In addition, because of the ever-increasing industrial demand for electricity, electric power infrastructure becomes larger and larger, equipment and transmission link structure are more and more complex, all kinds of faults emerge one after another and administrative department has more and more urgent demand for electrical inspection personnel in terms of solving problems of various equipments and links. At present, relying on the development of network communication technology, real-time video monitoring system of electric power system is being promoted in a large scale. Real-time video acquisition system of electrical inspection personnel based on mobile terminal will also be applied gradually. A Real-time Video Monitoring System (RVMS of mobile terminals based on Android platform is designed in this study. Through application test of practical environment, the system is able to meet the video data monitoring technique requirements of daily operation and maintenance of electric power system node. Mobile Video Acquisition Terminal (MVAT is able to collect relevant real-time video data in the process of equipment and link faults inspection as well as to provide the video data to remote system maintenance expert, offering data decision to expert in remote real-time solution of equipment failure. All collected video data will be stored in remote system server for establishing a decision database of video information, so as to provide convincing data support for future performance analysis and fault detection of related equipment and link.

  13. Wind power in power systems

    CERN Document Server

    Ackermann, Thomas

    2012-01-01

    The second edition of the highly acclaimed Wind Power in Power Systems has been thoroughly revised and expanded to reflect the latest challenges associated with increasing wind power penetration levels. Since its first release, practical experiences with high wind power penetration levels have significantly increased. This book presents an overview of the lessons learned in integrating wind power into power systems and provides an outlook of the relevant issues and solutions to allow even higher wind power penetration levels. This includes the development of standard wind turbine sim

  14. 适用于风电场的电能质量监测系统%Power Quality Monitoring System for Wind Farm

    Institute of Scientific and Technical Information of China (English)

    李彦臻

    2013-01-01

      is paper described the power quality monitoring system of a wind farm. It analyzed the system functions and power quality monitoring algorithm. Combined with practical application, it obtained the practicality of the power quality monitoring system and provided the data for the follow-up study of wind farm power quality problems.%  本文介绍了一款适用于风电场的电能质量监测系统。文章对系统功能和电能质量监测算法进行了详细的说明,并结合实际应用,得出该电能质量监测系统的实用性,为后续研究风电场的电能质量问题提供数据依据。

  15. Solar Powered Radioactive Air Monitoring Stations

    Energy Technology Data Exchange (ETDEWEB)

    Barnett, J. Matthew; Bisping, Lynn E.; Gervais, Todd L.

    2013-10-30

    Environmental monitoring of ambient air for radioactive material is required as stipulated in the PNNL Site radioactive air license. Sampling ambient air at identified preferred locations could not be initially accomplished because utilities were not readily available. Therefore, solar powered environmental monitoring systems were considered as a possible option. PNNL purchased two 24-V DC solar powered environmental monitoring systems which consisted of solar panels, battery banks, and sampling units. During an approximate four month performance evaluation period, the solar stations operated satisfactorily at an on-site test location. They were subsequently relocated to their preferred locations in June 2012 where they continue to function adequately under the conditions found in Richland, Washington.

  16. Low power and self-reconfigurable WBAN controller for continuous bio-signal monitoring system

    NARCIS (Netherlands)

    Lee, S.; Yoo, H.J.

    2013-01-01

    The WBAN controller with Branched Bus (BB) topology and Continuous Data Transmission (CDT) protocol with low power consumption and self- reconfigurability is proposed for wearable healthcare applications. The BB topology and CDT protocol is a combination of conventional Bus and Star topology and a v

  17. Development of a low cost and low power consumption system for monitoring CO_{2} soil concentration in volcanic areas.

    Science.gov (United States)

    Awadallah Estévez, Shadia; Moure-García, David; Torres-González, Pedro; Acosta Sánchez, Leopoldo; Domínguez Cerdeña, Itahiza

    2017-04-01

    Volatiles dissolved in magma are released as gases when pressure or stress conditions change. H2O, CO2, SO2 and H2S are the most abundant gases involved in volcanic processes. Emission rates are related to changes in the volcanic activity. Therefore, in order to predict possible eruptive events, periodic measurements of CO2 concentrations from the soil should be carried out. In the last years, CO2 monitoring has been widespread for many reasons. A direct relationship between changes in volcanic activity and variations in concentration, diffuse flux and isotope ratios of this gas, have been observed prior to some eruptions or unrest processes. All these factors have pointed out the fact that CO2 emission data are crucial in volcanic monitoring programs. In addition, relevant instrumentation development has also taken place: improved accuracy, cost reduction and portability. Considering this, we propose a low cost and a low power consumption system for measuring CO2 concentration in the soil based on Arduino. Through a perforated pick-axe buried at a certain depth, gas samples are periodically taken with the aid of a piston. These samples are injected through a pneumatic circuit in the spectrometer, which measures the CO2 concentration. Simultaneously, the system records the following meteorological parameters: atmospheric pressure, precipitation, relative humidity and air and soil temperature. These parameters are used to correct their possible influence in the CO2 soil concentration. Data are locally stored (SD card) and transmitted via GPRS or WIFI to a data analysis center.

  18. Development of power transmission tower monitoring system. Landslide detection by GPS carrier sensor; Soden tetto ijo kanshi system no kaihatsu. GPS carrier sensor ni yoru jisuberi kenshutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-01-01

    In order to reduce labor required for monitoring, patrolling, and checking anomalies in power transmission towers, a development has been made on a remotely controlled monitoring system that can detect landslides easily by detecting carrier waves from the global positioning system (GPS) in combination with use of cellular phones. The present system does not use code signals from the GPS, but receives carrier waves used for its transmission at two locations, measures precisely the phase difference therein, and calculates a very small change in the distance between two points from difference in arrival time of the waves. Receivers are placed at base points (substations) and GPS measuring points (transmission towers). Pocket bells are called from a personal computer at the maintenance location (a power center) during observation, and power is supplied into the receivers from solar cells. The data of GPS carrier waves received at both locations are transmitted to the power center through a cellular phone. The phase difference is calculated and the amount of movement is displayed on the personal computer screen to carry out remote surveillance. A measurement of accuracy of about 1 cm may be realized. Demonstration tests have begun in 1995 at towers installed in the Shiga plateau district where landslide occurs frequently, and the feasibility of the system was verified. 5 figs.

  19. VME system monitor board

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    Much of the machinery throughout the APS will be controlled by VME based computers. In order to increase the reliability of the system, it is necessary to be able to monitor the status of each VME crate. In order to do this, a VME System Monitor was created. In addition to being able to monitor and report the status (watchdog timer, temperature, CPU (Motorola MVME 167) state (status, run, fail), and the power supply), it includes provisions to remotely reset the CPU and VME crate, digital I/O, and parts of the transition module (serial port and ethernet connector) so that the Motorla MVME 712 is not needed. The standard VME interface was modified on the System Monitor so that in conjunction with the Motorola MVME 167 a message based VXI interrupt handler could is implemented. The System Monitor is a single VME card (6U). It utilizes both the front panel and the P2 connector for I/O. The front panel contains a temperature monitor, watchdog status LED, 4 general status LEDs, input for a TTL interrupt, 8 binary inputs (24 volt, 5 volt, and dry contact sense), 4 binary outputs (dry contact, TTL, and 100 mA), serial port (electrical RS-232 or fiber optic), ethernet transceiver (10 BASE-FO or AUI), and a status link to neighbor crates. The P2 connector is used to provide the serial port and ethernet to the processor. In order to abort and read the status of the CPU, a jumper cable must be connected between the CPU and the System Monitor.

  20. Buncher Power Source Monitoring System of 100 MeV Cyclotron

    Institute of Scientific and Technical Information of China (English)

    WEI; Jun-yi; FU; Xiao-liang; GUO; Juan-juan; ZHANG; Yi-wang; CAO; Xue-long; YIN; Zhi-guo; JI; Bin

    2015-01-01

    The 100MeV cyclotron provides 70-100MeV and 200μA proton beam,which can be used in astrophysics,medical,defense,energy and other fields.Buncher system can enhance the beam intensity and expand the scope of application of the accelerator.Buncher system is one part of the

  1. Minimization of the energy loss of nuclear power plants in case of partial in-core monitoring system failure

    Science.gov (United States)

    Zagrebaev, A. M.; Ramazanov, R. N.; Lunegova, E. A.

    2017-01-01

    In this paper we consider the optimization problem minimize of the energy loss of nuclear power plants in case of partial in-core monitoring system failure. It is possible to continuation of reactor operation at reduced power or total replacement of the channel neutron measurements, requiring shutdown of the reactor and the stock of detectors. This article examines the reconstruction of the energy release in the core of a nuclear reactor on the basis of the indications of height sensors. The missing measurement information can be reconstructed by mathematical methods, and replacement of the failed sensors can be avoided. It is suggested that a set of ‘natural’ functions determined by means of statistical estimates obtained from archival data be constructed. The procedure proposed makes it possible to reconstruct the field even with a significant loss of measurement information. Improving the accuracy of the restoration of the neutron flux density in partial loss of measurement information to minimize the stock of necessary components and the associated losses.

  2. 船舶电能监控系统的设计%Design of shipboard power monitoring system

    Institute of Scientific and Technical Information of China (English)

    肖春辉; 王唯一

    2013-01-01

    The power system is the"heart"of the ship system. It is related closely with other various systems of the ship,directly related to the security and reliability of the ship. Efficient and reliable electricity supply is the basic conditions of the economic and running of the ship systems. The computer system based on Lab VIEW has been applied as the means of monitoring system. The voltage, frequency, unbalance, harmonic index, and voltage fluctuations of the ship power system can be real-time data acquired,analyzed and processed,and displayed; Basic hardware structure of the system and software design is introduced in this paper,and a series of tests has been done. The results of tests show that the system works well.%电力系统是船舶系统的“心脏”,它与船舶的其他各个系统紧密相关,直接关系到船舶系统运行的安全性与和可靠性.高效可靠的电能供给是船舶系统经济运行与提高可靠性的基本条件.采用计算机系统作为监控手段,以NI公司的LabVIEW为系统开发平台,设计了一种能够对船舶电力系统中电压、频率、不平衡度、谐波指数、电压波动等进行实时数据采集、分析处理、显示、数据保存以及异常报警等功能的监测系统.介绍了系统的基本硬件结构和软件设计,并进行了一系列试验,试验结果表明系统运行效果良好.

  3. Condition Monitoring of Power Cables

    OpenAIRE

    Lewin, P L; L. Hao; Swaffield, D J; Swingler, S.G.

    2007-01-01

    A National Grid funded research project at Southampton has investigated possible methodologies for data acquisition, transmission and processing that will facilitate on-line continuous monitoring of partial discharges in high voltage polymeric cable systems. A method that only uses passive components at the measuring points has been developed and is outlined in this paper. More recent work, funded through the EPSRC Supergen V, UK Energy Infrastructure (AMPerES) grant in collaboration with UK ...

  4. The role of predictive on-line monitoring systems in the power generation industry

    Energy Technology Data Exchange (ETDEWEB)

    Gittings, S.D.; Baldwin, J. [AEA Technology Energy plc (United Kingdom)

    1998-12-31

    It has been apparent in the power generation sector for some time that utilities are moving away from large scale, labour intensive, inspection and overhaul programmes. These are being replaced by targeted inspection and replacement programmes supported by engineering assessment. Such engineering assessments address the predominant long-term damage mechanisms and are aimed at predicting failure timescales based upon historic operating data. From these predictions extended inspection intervals can be justified and replacement schedules planned in advance, ensuring maximum plant availability and deferred capital expenditure. However, as these assessments are based upon an examination of past operating history they must be periodically re-visited and up-dated. The cost of such reassessments is usually close to that performed initially, although cost savings can arise from reductions in work-scope which have been previously justified. As computers have become more advanced (and significantly cheaper) some of the expertise used in these assessments has been transferred into software based products. However, these products are generally aimed at replacing specific parts of the desk-based analysis, necessitating a suite of products to be used in order to address all of the components and damage mechanisms, which must be assessed. As these products require specialized knowledge to be used effectively they are often employed by consultants and rarely by plant operators, except in the largest of organisations which can support an in-house team of `experts`. This has in essence led to an increase in the number of companies capable of offering assessment services, but has maintained, in the majority of cases, the plant operators reliance upon external consultants. These software based assessment methods rely upon historic operating data (in the same manner as their desk- based counterparts) and hence also need to be periodically up-dated. However, as previous assessments can

  5. Power System Real-Time Monitoring by Using PMU-Based Robust State Estimation Method

    DEFF Research Database (Denmark)

    Zhao, Junbo; Zhang, Gexiang; Das, Kaushik;

    2016-01-01

    . To be specific, an adaptive weight assignment function to dynamically adjust the measurement weight based on the distance of big unwanted disturbances from the PMU measurements is proposed to increase algorithm robustness. Furthermore, a statistical test-based interpolation matrix H updating judgment strategy...... is proposed. The processed and resynced PMU information are used as priori information and incorporated to the modified weighted least square estimation to address the measurements imperfect synchronization between supervisory control and data acquisition and PMU measurements. Finally, the innovation analysis......-based bad data (BD) detection method, which can handle the smearing effect and critical measurement errors, is presented. We evaluate PRSEM by using IEEE benchmark test systems and a realistic utility system. The numerical results indicate that, in short computation time, PRSEM can effectively track...

  6. Remote Monitoring of Near-Surface Soil Moisture Dynamics In Unstable Slopes Using a Low-Power Autonomous Resistivity Imaging System

    Science.gov (United States)

    Chambers, J. E.; Meldrum, P.; Gunn, D.; Wilkinson, P. B.; Uhlemann, S.; Swift, R. T.; Kuras, O.; Inauen, C.; Hutchinson, D.; Butler, S.

    2016-12-01

    ERT monitoring has been demonstrated in numerous studies as an effective means of imaging near surface processes for applications as diverse as permafrost studies and contaminated land assessment. A limiting factor in applying time-lapse ERT for long-term studies in remote locations has been the availability of cost-effective ERT measurement systems designed specifically for monitoring applications. Typically, monitoring is undertaken using repeated manual data collection, or by building conventional survey instruments into a monitoring setup. The latter often requires high power and is therefore difficult to operate remotely without access to mains electricity. We describe the development of a low-power resistivity imaging system designed specifically for remote monitoring, taking advantage of, e.g., solar power and data telemetry. Here, we present the results of two field deployments. The system has been installed on an active railway cutting to provide insights into the effect of vegetation on the moisture dynamics in unstable infrastructure slopes and to gather subsurface information for pro-active remediation measures. The system, comprising 255 electrodes, acquires 4596 reciprocal measurement pairs twice daily during standard operation. In case of severe weather events, the measurement schedule is reactively changed, to gather high temporal resolution data to image rainfall infiltration processes. The system has also been installed along a leaking and marginally stable canal embankment; a less favourable location for remote monitoring, with limited solar power and poor mobile reception. Nevertheless, the acquired data indicated the effectiveness of remedial actions on the canal. The ERT results showed that one leak was caused by the canal and fixed during remediation, while two other "leaks" were shown to be effects of groundwater dynamics. The availability of cost-effective, low-power ERT monitoring instrumentation, combined with an automated workflow of

  7. Remote power quality monitoring system based on EtherNet%基于ARM的远程电能质量监测系统

    Institute of Scientific and Technical Information of China (English)

    赵燕君; 任卫东

    2012-01-01

    With the rapid development of society and economy, the power quality problems are getting worse, so making efficient power quality monitoring is becoming increasingly important. A power quality monitoring system based on ARM through the request of power monitoring was designed in this paper. By this system, the acquisition of real-time signal was completed, and a WEB server using embedded Linux with the TCP/IP protocol stack was built. In this way, the personnel could visit the system from any WEB browser. It is a new method for the long-distance power quality monitoring.%随着社会的进步和经济的快速发展,电能质量问题不断恶化,高效的电能质量监测变得越来越重要.从电力监测的实际要求出发,设计了基于ARM的电能质量综合监测系统,系统完成实时信号的采集,并利用嵌入式Linux自带的TCP/IP协议栈内建一个WEB服务器,工作人员可以在任何一个WEB浏览器访问这个系统.这对于地域跨越大的电网的远程监测提供了一种新思路.

  8. Reliability of Power Electronic Converter Systems

    DEFF Research Database (Denmark)

    -link capacitance in power electronic converter systems; wind turbine systems; smart control strategies for improved reliability of power electronics system; lifetime modelling; power module lifetime test and state monitoring; tools for performance and reliability analysis of power electronics systems; fault......-tolerant adjustable speed drive systems; mission profile oriented reliability design in wind turbine and photovoltaic systems; reliability of power conversion systems in photovoltaic applications; power supplies for computers; and high-power converters. Reliability of Power Electronic Converter Systems is essential...... reading for researchers, professionals and students working with power electronics and their applications, particularly those specializing in the development and application of power electronic converters and systems....

  9. Inductive Monitoring System (IMS)

    Data.gov (United States)

    National Aeronautics and Space Administration — IMS: Inductive Monitoring System The Inductive Monitoring System (IMS) is a tool that uses a data mining technique called clustering to extract models of normal...

  10. Flight Systems Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I project will develop the Flight System Monitor which will use non-intrusive electrical monitoring (NEMO). The electronic system health of...

  11. Intelligent Component Monitoring for Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Lefteri Tsoukalas

    2010-07-30

    Reliability and economy are two major concerns for a nuclear power generation system. Next generation nuclear power reactors are being developed to be more reliable and economic. An effective and efficient surveillance system can generously contribute toward this goal. Recent progress in computer systems and computational tools has made it necessary and possible to upgrade current surveillance/monitoring strategy for better performance. For example, intelligent computing techniques can be applied to develop algorithm that help people better understand the information collected from sensors and thus reduce human error to a new low level. Incidents incurred from human error in nuclear industry are not rare and have been proven costly. The goal of this project is to develop and test an intelligent prognostics methodology for predicting aging effects impacting long-term performance of nuclear components and systems. The approach is particularly suitable for predicting the performance of nuclear reactor systems which have low failure probabilities (e.g., less than 10-6 year-). Such components and systems are often perceived as peripheral to the reactor and are left somewhat unattended. That is, even when inspected, if they are not perceived to be causing some immediate problem, they may not be paid due attention. Attention to such systems normally involves long term monitoring and possibly reasoning with multiple features and evidence, requirements that are not best suited for humans.

  12. Power management system

    Science.gov (United States)

    Algrain, Marcelo C.; Johnson, Kris W.; Akasam, Sivaprasad; Hoff, Brian D.

    2007-10-02

    A method of managing power resources for an electrical system of a vehicle may include identifying enabled power sources from among a plurality of power sources in electrical communication with the electrical system and calculating a threshold power value for the enabled power sources. A total power load placed on the electrical system by one or more power consumers may be measured. If the total power load exceeds the threshold power value, then a determination may be made as to whether one or more additional power sources is available from among the plurality of power sources. At least one of the one or more additional power sources may be enabled, if available.

  13. CloudMonitor: Profiling Power Usage

    CERN Document Server

    Smith, James William; Ward, Jonathan Stuart; Sommerville, Ian

    2012-01-01

    In Cloud Computing platforms the addition of hardware monitoring devices to gather power usage data can be impractical or uneconomical due to the large number of machines to be metered. CloudMonitor, a monitoring tool that can generate power models for software-based power estimation, can provide insights to the energy costs of deployments without additional hardware. Accurate power usage data leads to the possibility of Cloud providers creating a separate tariff for power and therefore incentivizing software developers to create energy-efficient applications.

  14. Pilot evaluation of electricity-reliability and power-quality monitoring in California's Silicon Valley with the I-Grid(R) system

    Energy Technology Data Exchange (ETDEWEB)

    Eto, Joseph; Divan, Deepak; Brumsickle, William

    2004-02-01

    Power-quality events are of increasing concern for the economy because today's equipment, particularly computers and automated manufacturing devices, is susceptible to these imperceptible voltage changes. A small variation in voltage can cause this equipment to shut down for long periods, resulting in significant business losses. Tiny variations in power quality are difficult to detect except with expensive monitoring equipment used by trained technicians, so many electricity customers are unaware of the role of power-quality events in equipment malfunctioning. This report describes the findings from a pilot study coordinated through the Silicon Valley Manufacturers Group in California to explore the capabilities of I-Grid(R), a new power-quality monitoring system. This system is designed to improve the accessibility of power-quality in formation and to increase understanding of the growing importance of electricity reliability and power quality to the economy. The study used data collected by I-Grid sensors at seven Silicon Valley firms to investigate the impacts of power quality on individual study participants as well as to explore the capabilities of the I-Grid system to detect events on the larger electricity grid by means of correlation of data from the sensors at the different sites. In addition, study participants were interviewed about the value they place on power quality, and their efforts to address electricity-reliability and power-quality problems. Issues were identified that should be taken into consideration in developing a larger, potentially nationwide, network of power-quality sensors.

  15. Development and application of a high-speed, high-resolution data acquisition system for monitoring power at the service entrance to buildings

    Energy Technology Data Exchange (ETDEWEB)

    Sharp, T.R.

    1995-02-01

    A non-intrusive load monitoring system (NILMS) was developed and tested to determine its capabilities and examine ways that the system can supplement the understanding of how energy is used in a building. The investigation of the system as a method for obtaining short-term building energy use and demand data faster, as less cost, with less complexity, and less intrusively than from conventional submetering is described in this report. Data acquisition hardware and software, a power transducer, and current transformers were assembled into a system that could be used to sample the instantaneous real and reactive power coming into a building. The system was used to collect power profiles at a commercial and a residential building. The NILMS can sample power at low speeds (one sample per hour or less) and at speeds exceeding 100 Hz. Large changes in building power such as those due to central heating and cooling systems, water heaters, or banks of lights can easily be discriminated from total building power profiles collected by the system. Smaller loads, less than 1 or 2 kW, can be resolved when there is little ``noise`` in the power profile. Very small loads, less than 100 W, can be resolved in a residential application. Resolution becomes more difficult as larger and more frequent fluctuations occur. The ability of the system to easily collect valuable, short-term building power profiles, which permit individual loads to be determined (resolved), makes the system attractive for a number of applications. The system could prove very useful for measuring short-term energy use and demand, assisting building energy auditors in assessing building deficiencies, providing short-term performance data for validating engineering-based savings estimates and calibrating computer-based building performance models, and for validating, developing, and/or improving building and building system operating strategies.

  16. Development and application of a high-speed, high-resolution data acquisition system for monitoring power at the service entrance to buildings

    Energy Technology Data Exchange (ETDEWEB)

    Sharp, T.R.

    1995-02-01

    A non-intrusive load monitoring system (NILMS) was developed and tested to determine its capabilities and examine ways that the system can supplement the understanding of how energy is used in a building. The investigation of the system as a method for obtaining short-term building energy use and demand data faster, as less cost, with less complexity, and less intrusively than from conventional submetering is described in this report. Data acquisition hardware and software, a power transducer, and current transformers were assembled into a system that could be used to sample the instantaneous real and reactive power coming into a building. The system was used to collect power profiles at a commercial and a residential building. The NILMS can sample power at low speeds (one sample per hour or less) and at speeds exceeding 100 Hz. Large changes in building power such as those due to central heating and cooling systems, water heaters, or banks of lights can easily be discriminated from total building power profiles collected by the system. Smaller loads, less than 1 or 2 kW, can be resolved when there is little ``noise`` in the power profile. Very small loads, less than 100 W, can be resolved in a residential application. Resolution becomes more difficult as larger and more frequent fluctuations occur. The ability of the system to easily collect valuable, short-term building power profiles, which permit individual loads to be determined (resolved), makes the system attractive for a number of applications. The system could prove very useful for measuring short-term energy use and demand, assisting building energy auditors in assessing building deficiencies, providing short-term performance data for validating engineering-based savings estimates and calibrating computer-based building performance models, and for validating, developing, and/or improving building and building system operating strategies.

  17. Monitoring systems online of oil for transformers of nuclear power plants; Sistemas de monitorizacion online del aceite para transformadores de potencia de Centrales

    Energy Technology Data Exchange (ETDEWEB)

    Sarandeses, S.

    2014-07-01

    The nuclear power plants are showing their concern due to the existence of recent failures related to the bulky transformers of power. These transformers are not security, but are important for the production of power as its failure can cause transient on the floor, reactor scram or shooting, that can cause interruptions in the production of energy or might force us to reduce the power of production The analysis of gases dissolved in transformer oil is recognized as a trial key to identify a submerged transformer failure in oil. With this analysis it is not possible to ensure that there is no damage in the transformer, but the probability of risk of this type of failure can be reduced. The industry recommended to equip the new large power transformers with oil online monitoring systems and in some cases also be It recommended its use in existing transformers. (Author)

  18. Automatic chemical monitoring in the composition of functions performed by the unit level control system in the new projects of nuclear power plant units

    Science.gov (United States)

    Denisova, L. G.; Khrennikov, N. N.

    2014-08-01

    The article presents information on the state of regulatory framework and development of a subsystem for automated chemical monitoring of water chemistries in the primary and secondary coolant circuits used as part of the automatic process control system in new projects of VVER reactor-based nuclear power plant units. For the strategy of developing and putting in use the water chemistry-related part of the automated process control system within the standard AES-2006 nuclear power plant project to be implemented, it is necessary to develop regulatory documents dealing with certain requirements imposed on automatic water chemistry monitoring systems in accordance with the requirements of federal codes and regulations in the field of using atomic energy.

  19. Design of Power Supply Monitoring System for Fire Protection Equipment%消防设备电源监控系统设计

    Institute of Scientific and Technical Information of China (English)

    杨春丽

    2015-01-01

    对消防设备电源监控系统相关规范及标准进行分析及梳理,分析归纳消防设备电源、消防设备电源监控系统的定义及作用,结合某大型城市综合体工程,介绍消防设备电源监控系统的设置场所、范围、部位、布线等设计。%Relevant national regulations and standards regarding power supply monitoring system for fire protection equipment are analyzed and summarized. Definitions and functions of power supply for fire protection equipments and power supply monitoring systems for fire protection equipment are analyzed and summarized. Based on a large urban complex project, the setting place, range, location, wiring and other designs of power supply monitoring system for fire protection equipment are introduced.

  20. A wearable, low-power, health-monitoring instrumentation based on a Programmable System-on-Chip.

    Science.gov (United States)

    Massot, Bertrand; Gehin, Claudine; Nocua, Ronald; Dittmar, Andre; McAdams, Eric

    2009-01-01

    Improvement in quality and efficiency of health and medicine, at home and in hospital, has become of paramount importance. The solution of this problem would require the continuous monitoring of several key patient parameters, including the assessment of autonomic nervous system (ANS) activity using non-invasive sensors, providing information for emotional, sensorial, cognitive and physiological analysis of the patient. Recent advances in embedded systems, microelectronics, sensors and wireless networking enable the design of wearable systems capable of such advanced health monitoring. The subject of this article is an ambulatory system comprising a small wrist device connected to several sensors for the detection of the autonomic nervous system activity. It affords monitoring of skin resistance, skin temperature and heart activity. It is also capable of recording the data on a removable media or sending it to computer via a wireless communication. The wrist device is based on a Programmable System-on-Chip (PSoC) from Cypress: PSoCs are mixed-signal arrays, with dynamic, configurable digital and analogical blocks and an 8-bit Microcontroller unit (MCU) core on a single chip. In this paper we present first of all the hardware and software architecture of the device, and then results obtained from initial experiments.

  1. Induced Seismicity Monitoring System

    Science.gov (United States)

    Taylor, S. R.; Jarpe, S.; Harben, P.

    2014-12-01

    There are many seismological aspects associated with monitoring of permanent storage of carbon dioxide (CO2) in geologic formations. Many of these include monitoring underground gas migration through detailed tomographic studies of rock properties, integrity of the cap rock and micro seismicity with time. These types of studies require expensive deployments of surface and borehole sensors in the vicinity of the CO2 injection wells. Another problem that may exist in CO2 sequestration fields is the potential for damaging induced seismicity associated with fluid injection into the geologic reservoir. Seismic hazard monitoring in CO2 sequestration fields requires a seismic network over a spatially larger region possibly having stations in remote settings. Expensive observatory-grade seismic systems are not necessary for seismic hazard deployments or small-scale tomographic studies. Hazard monitoring requires accurate location of induced seismicity to magnitude levels only slightly less than that which can be felt at the surface (e.g. magnitude 1), and the frequencies of interest for tomographic analysis are ~1 Hz and greater. We have developed a seismo/acoustic smart sensor system that can achieve the goals necessary for induced seismicity monitoring in CO2 sequestration fields. The unit is inexpensive, lightweight, easy to deploy, can operate remotely under harsh conditions and features 9 channels of recording (currently 3C 4.5 Hz geophone, MEMS accelerometer and microphone). An on-board processor allows for satellite transmission of parameter data to a processing center. Continuous or event-detected data is kept on two removable flash SD cards of up to 64+ Gbytes each. If available, data can be transmitted via cell phone modem or picked up via site visits. Low-power consumption allows for autonomous operation using only a 10 watt solar panel and a gel-cell battery. The system has been successfully tested for long-term (> 6 months) remote operations over a wide range

  2. Remote Maintenance Monitoring System -

    Data.gov (United States)

    Department of Transportation — The Remote Maintenance and Monitoring System (RMMS) is a collection of subsystems that includes telecommunication components, hardware, and software, which serve to...

  3. Aerospace Systems Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Proposal Title: Aerospace Systems Monitor PHASE 1 Technical Abstract: This Phase II STTR project will continue development and commercialization of the Aerospace...

  4. FAULT PROPAGATION AND EFFECTS ANALYSIS FOR DESIGNING AN ONLINE MONITORING SYSTEM FOR THE SECONDARY LOOP OF A NUCLEAR POWER PLANT PART OF A HYBRID ENERGY SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Li, Huijuan; Diao, Xiaoxu; Li, Boyuan; Smidts, Carol; Bragg-Sitton, Shannon

    2017-03-01

    This paper studies the propagation and effects of faults of critical components that pertain to the secondary loop of a nuclear power plant found in Nuclear Hybrid Energy Systems (NHES). This information is used to design an on-line monitoring (OLM) system which is capable of detecting and forecasting faults that are likely to occur during NHES operation. In this research, the causes, features, and effects of possible faults are investigated by simulating the propagation of faults in the secondary loop. The simulation is accomplished by using the Integrated System Failure Analysis (ISFA). ISFA is used for analyzing hardware and software faults during the conceptual design phase. In this paper, the models of system components required by ISFA are initially constructed. Then, the fault propagation analysis is implemented, which is conducted under the bounds set by acceptance criteria derived from the design of an OLM system. The result of the fault simulation is utilized to build a database for fault detection and diagnosis, provide preventive measures, and propose an optimization plan for the OLM system.

  5. Wireless Sensor Network Powered by a Terrestrial Microbial Fuel Cell as a Sustainable Land Monitoring Energy System

    Directory of Open Access Journals (Sweden)

    Andrea Pietrelli

    2014-10-01

    Full Text Available This work aims at investigating the possibility of a wireless sensor network powered by an energy harvesting technology, such as a microbial fuel cell (MFC. An MFC is a bioreactor that transforms energy stored in chemical bonds of organic compounds into electrical energy. This process takes place through catalytic reactions of microorganisms under anaerobic conditions. An anode chamber together with a cathode chamber composes a conventional MFC reactor. The protons generated in the anode chamber are then transferred into the cathode chamber through a proton exchange membrane (PEM. A possible option is to use the soil itself as the membrane. In this case, we are referring to, more properly, a terrestrial microbial fuel cell (TMFC. This research examines the sustainability of a wireless sensor network powered by TMFC for land monitoring and precision agriculture. Acting on several factors, such as pH, temperature, humidity and type of soil used, we obtained minimum performance requirements in terms of the output power of the TMFC. In order to identify some of the different network node configurations and to compare the resulting performance, we investigated the energy consumption of the core components of a node, e.g., the transceiver and microcontroller, looking for the best performance.

  6. Crosslinking and condition monitoring with wind power plants; Vernetzung und Condition Monitoring bei Windenergieanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Spelter, Frank [Bachmann Electronic GmbH, Feldkirch (Austria). Unternehmenskommunikation

    2010-10-15

    Condition monitoring of wind power systems is getting increasingly important, and there are various possible approaches. The Bachmann M1 automation system allows the implementation of measuring and control processes and evaluations up to comprehensive condition monitoring. In combination with an expert system, it is possible to monitor mechanical and technical components and to detect defects before these will have negative effects on the system condition. (orig.)

  7. Application of Wind Power Monitoring System Based on OPC Technology%基于OPC技术在风电监控系统上的应用

    Institute of Scientific and Technical Information of China (English)

    李晓斌; 王迪

    2011-01-01

    Wind power,a kind of green and clean energy is widely emphasized in all of countries. OPC technology is introduced in this article. A wind power monitoring system is applied based on OPC technology at low cost.%风电作为成熟的绿色能源受到各国的重视.在介绍OPC技术的基础上提出并实现了基于OPC技术的低成本的风电监控系统的应用方案.

  8. A grid job monitoring system

    Energy Technology Data Exchange (ETDEWEB)

    Dumitrescu, Catalin; /Fermilab; Nowack, Andreas; /Aachen, Tech. Hochsch.; Padhi, Sanjay; /UC, San Diego; Sarkar, Subir; /INFN, Pisa /Pisa, Scuola Normale Superiore

    2010-01-01

    This paper presents a web-based Job Monitoring framework for individual Grid sites that allows users to follow in detail their jobs in quasi-real time. The framework consists of several independent components: (a) a set of sensors that run on the site CE and worker nodes and update a database, (b) a simple yet extensible web services framework and (c) an Ajax powered web interface having a look-and-feel and control similar to a desktop application. The monitoring framework supports LSF, Condor and PBS-like batch systems. This is one of the first monitoring systems where an X.509 authenticated web interface can be seamlessly accessed by both end-users and site administrators. While a site administrator has access to all the possible information, a user can only view the jobs for the Virtual Organizations (VO) he/she is a part of. The monitoring framework design supports several possible deployment scenarios. For a site running a supported batch system, the system may be deployed as a whole, or existing site sensors can be adapted and reused with the web services components. A site may even prefer to build the web server independently and choose to use only the Ajax powered web interface. Finally, the system is being used to monitor a glideinWMS instance. This broadens the scope significantly, allowing it to monitor jobs over multiple sites.

  9. Monitoring solar gain. Performance of an industrial-scale solar thermal power system; Anlagenertraege kontrollieren. Betriebsergebnisse einer solarthermischen Grossanlage

    Energy Technology Data Exchange (ETDEWEB)

    Haug, W.; Rittmann, B. [Fachhochschule Aalen (Germany)

    2001-05-01

    The Carl-Schneider students' hostel of Aalen Technical University gets its warm water from a solar systems. A faulty return valve was detected during a routine check, and the authors therefore stress the need for continuous monitoring of solar systems. [German] Eine Solarwaermeanlage versorgt das Carl-Schneider-Studentenheim der Fachhochschule Aalen mit Warmwasser. Sie funktioniert tadellos. Dem war nicht immer so. Ein klemmendes Rueckschlagventil waere wohl nie entdeckt worden, haette es nicht eine Abnahmemessung gegeben. Die Autoren, Professoren an der Fachhochschule, plaedieren deshalb fuer eine kontinuierliche Ueberwachung von Solaranlagen. (orig.)

  10. Monitoring Cray Cooling Systems

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, Don E [ORNL; Ezell, Matthew A [ORNL; Becklehimer, Jeff [Cray, Inc.; Donovan, Matthew J [ORNL; Layton, Christopher C [ORNL

    2014-01-01

    While sites generally have systems in place to monitor the health of Cray computers themselves, often the cooling systems are ignored until a computer failure requires investigation into the source of the failure. The Liebert XDP units used to cool the Cray XE/XK models as well as the Cray proprietary cooling system used for the Cray XC30 models provide data useful for health monitoring. Unfortunately, this valuable information is often available only to custom solutions not accessible by a center-wide monitoring system or is simply ignored entirely. In this paper, methods and tools used to harvest the monitoring data available are discussed, and the implementation needed to integrate the data into a center-wide monitoring system at the Oak Ridge National Laboratory is provided.

  11. Light weight, high-speed, and self-powered wireless fiber optic sensor (WiFOS) structural health monitor system for avionics and aerospace environments

    Science.gov (United States)

    Mendoza, Edgar A.; Kempen, Cornelia; Sun, Sunjian; Esterkin, Yan

    2014-09-01

    This paper describes recent progress towards the development of an innovative light weight, high-speed, and selfpowered wireless fiber optic sensor (WiFOS™) structural health monitor system suitable for the onboard and in-flight unattended detection, localization, and classification of load, fatigue, and structural damage in advanced composite materials commonly used in avionics and aerospace systems. The WiFOS™ system is based on ROI's advancements on monolithic photonic integrated circuit microchip technology, integrated with smart power management, on-board data processing, wireless data transmission optoelectronics, and self-power using energy harvesting tools such as solar, vibration, thermoelectric, and magneto-electric. The self-powered, wireless WiFOS™ system offers a versatile and powerful SHM tool to enhance the reliability and safety of avionics platforms, jet fighters, helicopters, commercial aircraft that use lightweight composite material structures, by providing comprehensive information about the structural integrity of the structure from a large number of locations. Immediate SHM applications are found in rotorcraft and aircraft, ships, submarines, and in next generation weapon systems, and in commercial oil and petrochemical, aerospace industries, civil structures, power utilities, portable medical devices, and biotechnology, homeland security and a wide spectrum of other applications.

  12. Circuit of power quality monitoring system for wireless transmission%无线传输的电能质量监测系统电路

    Institute of Scientific and Technical Information of China (English)

    陈允刚

    2015-01-01

    Real time monitoring of power quality is to improve production efficiency,key energy-saving emission reduction,safety in production,this paper in Baotou park equipment of power quality requirements proposed a based on the ZigBee wireless sensor network electric energy quality monitoring system.The system not only has powerful functions in measurement and communication,and has convenient networking,the characteristics of dynamic topology,low cost,large capacity,high reliability,can well meet the high-tech industrial park electrical quality real-time monitoring of the actual needs.%电能质量的实时监测是提高生产效率、节能减排、安全生产的关键,本文针对包头装备园区对电能质量的要求,提出了一种基于ZigBee无线传感网络的电能质量实时监测系统.该系统不仅具有强大的测量和通信功能,而且具有组网方便、动态拓扑、低成本、大容量、高可靠性的特点,能很好地满足高科技工业园电能质量实时监测的实际需要.

  13. Electric power systems

    CERN Document Server

    Weedy, B M; Jenkins, N; Ekanayake, J B; Strbac, G

    2012-01-01

    The definitive textbook for Power Systems students, providing a grounding in essential power system theory while also focusing on practical power engineering applications. Electric Power Systems has been an essential book in power systems engineering for over thirty years. Bringing the content firmly up-to-date whilst still retaining the flavour of Weedy's extremely popular original, this Fifth Edition has been revised by experts Nick Jenkins, Janaka Ekanayake and Goran Strbac. This wide-ranging text still covers all of the fundamental power systems subjects but is now e

  14. 基于WSN技术电能监测系统设计%Design of power monitoring system based on WSN technology

    Institute of Scientific and Technical Information of China (English)

    张慧颖; 黄南天

    2015-01-01

    In view of lack of the effective means of power quality monitoring in the traditional laboratory, this paper put forward a new wireless power quality monitoring system based on WSN technology.It consists of energy acquisition node, wireless transmission network and the monitoring center, and the wireless network is built by the combination of Zigbee technology and GPRS technology.This system uses AT7022B as the core of the acquisition node, and optimi-zes the routing nodes that composed of CC2530.The results shows that the correctness transfer rate of the system is up to 99 percent, and the system is featured with reliability, flexible networking, and low power consumption, which can effectively improved the laboratory power management.%针对传统的实验室缺少有效电能质量监测手段等现状,设计了一种基于WSN技术的无线电能质量监测系统. 系统由电能采集节点、无线传输网络和监控中心三部分组成,将Zigbee技术和GPRS技术有效结合实现了无线网络的搭建. 本系统以专用计量芯片AT7022B进行电能参数的采集,并对CC2530组成的路由节点进行优化设计. 实验结果表明,该系统传输正确率可达99%,而且系统可靠、组网灵活、低功耗,可有效提高实验室电能管理.

  15. Monitoring Systems for Hydropower Plants

    Directory of Open Access Journals (Sweden)

    Damaschin Pepa

    2015-07-01

    Full Text Available One of the most important issue in hydro power industry is to determine the necessary degree of automation in order to improve the operation security. Depending upon the complexity of the system (the power plant equipment the automation specialist will build a philosophy of control following some general principals of security and operation. Helped by the modern digital equipment, today is relative easy to design a complete monitoring and supervising system including all the subparts of a hydro aggregate. A series of sensors and transducers specific for each auxiliary installation of the turbine and generator will be provided, together with a PLC or an industrial PC that will run an application software for implementing the security and control algorithms. The purpose of this paper is to offer a general view of these issues, providing a view of designing an automation & control and security system for hydro power plants of small, medium and big power.

  16. Application of computer monitoring system in sugar mill power station%计算机监控技术在糖厂热电站的应用

    Institute of Scientific and Technical Information of China (English)

    甘耀明; 农志民

    2013-01-01

      In this paper, TAS9000 computer monitoring system’s technical characters were introduced, including system construction, equipments and its’ main functions. And application effect of this system in sugar mill power station was introduced.%  从系统构成、系统设备、系统主要功能等方面介绍了 TAS9000计算机监控系统的技术特点及糖厂发电站计算机监控系统的具体应用。

  17. Reconstruction Design for Computer Monitoring System of Lushui Power Plant%陆水电厂计算机监控系统改造设计

    Institute of Scientific and Technical Information of China (English)

    余春明; 杨流学; 陈康龙

    2012-01-01

    In terms of the problems of computer monitoring system of Lushui Power Station,design options are proposed,and the system is fully upgraded,eliminating the security risks and offering certain referential siginificance to the same type of computers.%针对陆水电厂计算机监控系统存在的问题,提出了设计方案,并对该系统进行了全面升级,消除了安全隐患,对同类型计算机监控系统的改造具有一定的借鉴意义。

  18. Adaptive Power Control of Hydropower Station Computer Monitoring System%水电厂监控系统适应式功率调节控制技术

    Institute of Scientific and Technical Information of China (English)

    邹桂丽; 魏加富; 王辉斌

    2013-01-01

    Aiming at the fact that, nowadays closed-loop power adjustment in most hydropower stations are realized by computer monitoring systems, this paper describes common modes of parameter regulation in monitoring system. And it also describes the necessity and feasibility of adaptive power adjustment control in computer monitoring system and the way of achieving it.%文章针对目前水电厂功率调节主要是在计算机监控系统中实现闭环调节的现状,描述了监控系统功率调节参数设置的常用模式,论述了计算机监控系统适应式功率调节控制的必要性和可行性,阐明了监控系统功率调节适应式控制技术的实现方法。

  19. Power system relaying

    CERN Document Server

    Horowitz, Stanley H; Niemira, James K

    2013-01-01

    The previous three editions of Power System Relaying offer comprehensive and accessible coverage of the theory and fundamentals of relaying and have been widely adopted on university and industry courses worldwide. With the third edition, the authors have added new and detailed descriptions of power system phenomena such as stability, system-wide protection concepts and discussion of historic outages. Power System Relaying, 4th Edition continues its role as an outstanding textbook on power system protection for senior and graduate students in the field of electric power engineering and a refer

  20. Shipboard electrical power systems

    CERN Document Server

    Patel, Mukund R

    2011-01-01

    Shipboard Electrical Power Systems addresses new developments in this growing field. Focused on the trend toward electrification to power commercial shipping, naval, and passenger vessels, this book helps new or experienced engineers master cutting-edge methods for power system design, control, protection, and economic use of power. Provides Basic Transferable Skills for Managing Electrical Power on Ships or on LandThis groundbreaking book is the first volume of its kind to illustrate optimization of all aspects of shipboard electrical power systems. Applying author Mukund Patel's rare combina

  1. Fatigue monitoring in Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Ware, A.G.; Shah, V.N. [Idaho National Engineering Laboratory, Idaho Falls, ID (United States)

    1995-04-01

    This paper summarizes fatigue monitoring methods and surveys their application in the nuclear power industry. The paper is based on a review of the technical literature. Two main reasons for fatigue monitoring are more frequent occurrence of some transients than that assumed in the fatigue design analysis and the discovery of stressors that were not included in the fatigue design analysis but may cause significant fatigue damage at some locations. One fatigue monitoring method involves use of plant operating data and procedures to update the fatigue usage. Another method involves monitoring of plant operating parameters using existing, or if needed, supplementary plant instrumentation for online computation of fatigue usage. Use of fatigue monitoring has better defined the operational transients. Most operational transients have been found less severe and fewer in numbers than anticipated in the design fatigue analysis. Use of fatigue monitoring has assisted in quantifying newly discovered stressors and has helped in detecting the presence of thermal stratification of unsuspected locations.

  2. Monitoring Biological Activity at Geothermal Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Peter Pryfogle

    2005-09-01

    The economic impact of microbial growth in geothermal power plants has been estimated to be as high as $500,000 annually for a 100 MWe plant. Many methods are available to monitor biological activity at these facilities; however, very few plants have any on-line monitoring program in place. Metal coupon, selective culturing (MPN), total organic carbon (TOC), adenosine triphosphate (ATP), respirometry, phospholipid fatty acid (PLFA), and denaturing gradient gel electrophoresis (DGGE) characterizations have been conducted using water samples collected from geothermal plants located in California and Utah. In addition, the on-line performance of a commercial electrochemical monitor, the BIoGEORGE?, has been evaluated during extended deployments at geothermal facilities. This report provides a review of these techniques, presents data on their application from laboratory and field studies, and discusses their value in characterizing and monitoring biological activities at geothermal power plants.

  3. Wireless power transfer system

    OpenAIRE

    Arai, Hiroyuki

    2012-01-01

    This paper presents a survey of recent wireless power transfer systems. The issue of wireless power transfer is to achieve a highly efficient system with small positioning errors of the facilities setting. Several theories have been presented to obtain precise system design. This paper presents a summary of design theory for short range power transfer systems and detailed formulations based on a circuit model and an array of infinitesimal dipoles. In addition to these theories, this paper in...

  4. Copilot: Monitoring Embedded Systems

    Science.gov (United States)

    Pike, Lee; Wegmann, Nis; Niller, Sebastian; Goodloe, Alwyn

    2012-01-01

    Runtime verification (RV) is a natural fit for ultra-critical systems, where correctness is imperative. In ultra-critical systems, even if the software is fault-free, because of the inherent unreliability of commodity hardware and the adversity of operational environments, processing units (and their hosted software) are replicated, and fault-tolerant algorithms are used to compare the outputs. We investigate both software monitoring in distributed fault-tolerant systems, as well as implementing fault-tolerance mechanisms using RV techniques. We describe the Copilot language and compiler, specifically designed for generating monitors for distributed, hard real-time systems. We also describe two case-studies in which we generated Copilot monitors in avionics systems.

  5. Energy harvesting to power embedded condition monitoring hardware

    Science.gov (United States)

    Farinholt, Kevin; Brown, Nathan; Siegel, Jake; McQuown, Justin; Humphris, Robert

    2015-04-01

    The shift toward condition-based monitoring is a key area of research for many military, industrial, and commercial customers who want to lower the overall operating costs of capital equipment and general facilities. Assessing the health of rotating systems such as gearboxes, bearings, pumps and other actuation systems often rely on the need for continuous monitoring to capture transient signals that are evidence of events that could cause (i.e. cavitation), or be the result of (i.e. spalling), damage within a system. In some applications this can be accomplished using line powered analyzers, however for wide-spread monitoring, the use of small-scale embedded electronic systems are more desirable. In such cases the method for powering the electronics becomes a significant design factor. This work presents a multi-source energy harvesting approach meant to provide a robust power source for embedded electronics, capturing energy from vibration, thermal and light sources to operate a low-power sensor node. This paper presents the general design philosophy behind the multi-source harvesting circuit, and how it can be extended from powering electronics developed for periodic monitoring to sensing equipment capable of providing continuous condition-based monitoring.

  6. SPORT及IDMA接口在电力系统监控产品中的应用%Using SPORT and IDMA in power system monitoring

    Institute of Scientific and Technical Information of China (English)

    孙瑞正

    2012-01-01

    电力系统监控产品中,模拟量数据流程是影响系统性能的重要因素。文中提出了一种基于ADSP中SPORT及IDMA的模拟量输入接口。实际应用表明,该方法可以简化数据流程,提高系统效率。%In monitor system for power system,the data-flow path of data acquisition system will effect the system performance .In this paper,a new data interface is presented base on SPORT and IDMA of ADSP,by which,the data-flow path can be simpled and the performance can be improved.

  7. The Development of an Open Hardware and Software System Onboard Unmanned Aerial Vehicles to Monitor Concentrated Solar Power Plants

    Directory of Open Access Journals (Sweden)

    Francisco Javier Mesas-Carrascosa

    2017-06-01

    Full Text Available Concentrated solar power (CSP plants are increasingly gaining interest as a source of renewable energy. These plants face several technical problems and the inspection of components such as absorber tubes in parabolic trough concentrators (PTC, which are widely deployed, is necessary to guarantee plant efficiency. This article presents a system for real-time industrial inspection of CSP plants using low-cost, open-source components in conjunction with a thermographic sensor and an unmanned aerial vehicle (UAV. The system, available in open-source hardware and software, is designed to be employed independently of the type of device used for inspection (laptop, smartphone, tablet or smartglasses and its operating system. Several UAV flight missions were programmed as follows: flight altitudes at 20, 40, 60, 80, 100 and 120 m above ground level; and three cruising speeds: 5, 7 and 10 m/s. These settings were chosen and analyzed in order to optimize inspection time. The results indicate that it is possible to perform inspections by an UAV in real time at CSP plants as a means of detecting anomalous absorber tubes and improving the effectiveness of methodologies currently being utilized. Moreover, aside from thermographic sensors, this contribution can be applied to other sensors and can be used in a broad range of applications where real-time georeferenced data visualization is necessary.

  8. The Development of an Open Hardware and Software System Onboard Unmanned Aerial Vehicles to Monitor Concentrated Solar Power Plants.

    Science.gov (United States)

    Mesas-Carrascosa, Francisco Javier; Verdú Santano, Daniel; Pérez Porras, Fernando; Meroño-Larriva, José Emilio; García-Ferrer, Alfonso

    2017-06-08

    Concentrated solar power (CSP) plants are increasingly gaining interest as a source of renewable energy. These plants face several technical problems and the inspection of components such as absorber tubes in parabolic trough concentrators (PTC), which are widely deployed, is necessary to guarantee plant efficiency. This article presents a system for real-time industrial inspection of CSP plants using low-cost, open-source components in conjunction with a thermographic sensor and an unmanned aerial vehicle (UAV). The system, available in open-source hardware and software, is designed to be employed independently of the type of device used for inspection (laptop, smartphone, tablet or smartglasses) and its operating system. Several UAV flight missions were programmed as follows: flight altitudes at 20, 40, 60, 80, 100 and 120 m above ground level; and three cruising speeds: 5, 7 and 10 m/s. These settings were chosen and analyzed in order to optimize inspection time. The results indicate that it is possible to perform inspections by an UAV in real time at CSP plants as a means of detecting anomalous absorber tubes and improving the effectiveness of methodologies currently being utilized. Moreover, aside from thermographic sensors, this contribution can be applied to other sensors and can be used in a broad range of applications where real-time georeferenced data visualization is necessary.

  9. Stochastic power system operation

    OpenAIRE

    Power, Michael

    2010-01-01

    This paper outlines how to economically and reliably operate a power system with high levels of renewable generation which are stochastic in nature. It outlines the challenges for system operators, and suggests tools and methods for meeting this challenge, which is one of the most fundamental since large scale power networks were instituted. The Ireland power system, due to its nature and level of renewable generation, is considered as an example in this paper.

  10. Optimization in power systems

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Geraldo R.M. da [Sao Paulo Univ., Sao Carlos, SP (Brazil). Escola de Engenharia

    1994-12-31

    This paper discusses, partially, the advantages and the disadvantages of the optimal power flow. It shows some of the difficulties of implementation and proposes solutions. An analysis is made comparing the power flow, BIGPOWER/CESP, and the optimal power flow, FPO/SEL, developed by the author, when applied to the CEPEL-ELETRONORTE and CESP systems. (author) 8 refs., 5 tabs.

  11. SITE ELECTRICAL POWER SYSTEM DESCRIPTION DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    E.P. McCann

    1999-04-16

    The Site Electrical Power System receives and distributes utility power to all North Portal site users. The major North Portal users are the Protected Area including the subsurface facility and Balance of Plant areas. The system is remotely monitored and controlled from the Surface Operations Monitoring and Control System. The system monitors power quality and provides the capability to transfer between Off-Site Utility and standby power (including dedicated safeguards and security power). Standby power is only distributed to selected loads for personnel safety and essential operations. Security power is only distributed to essential security operations. The standby safeguards and security power is independent from all other site power. The system also provides surface lighting, grounding grid, and lightning protection for the North Portal. The system distributes power during construction, operation, caretaker, and closure phases of the repository. The system consists of substation equipment (disconnect switches, breakers, transformers and grounding equipment) and power distribution cabling from substation to the north portal switch gear building. Additionally, the system includes subsurface facility substation (located on surface), switch-gear, standby diesel generators, underground duct banks, power cables and conduits, switch-gear building and associated distribution equipment for power distribution. Each area substation distributes power to the electrical loads and includes the site grounding, site lighting and lightning protection equipment. The site electrical power system distributes power of sufficient quantity and quality to meet users demands. The Site Electrical Power System interfaces with the North Portal surface systems requiring electrical power. The system interfaces with the Subsurface Electrical Distribution System which will supply power to the underground facilities from the North Portal. Power required for the South Portal and development side

  12. Space Nuclear Power Systems

    Science.gov (United States)

    Houts, Michael G.

    2012-01-01

    Fission power and propulsion systems can enable exciting space exploration missions. These include bases on the moon and Mars; and the exploration, development, and utilization of the solar system. In the near-term, fission surface power systems could provide abundant, constant, cost-effective power anywhere on the surface of the Moon or Mars, independent of available sunlight. Affordable access to Mars, the asteroid belt, or other destinations could be provided by nuclear thermal rockets. In the further term, high performance fission power supplies could enable both extremely high power levels on planetary surfaces and fission electric propulsion vehicles for rapid, efficient cargo and crew transfer. Advanced fission propulsion systems could eventually allow routine access to the entire solar system. Fission systems could also enable the utilization of resources within the solar system.

  13. Inherently safe passive gas monitoring system

    Energy Technology Data Exchange (ETDEWEB)

    Cordaro, Joseph V.; Bellamy, John Stephen; Shuler, James M.; Shull, Davis J.; Leduc, Daniel R.

    2016-09-06

    Generally, the present disclosure is directed to gas monitoring systems that use inductive power transfer to safely power an electrically passive device included within a nuclear material storage container. In particular, the electrically passive device can include an inductive power receiver for receiving inductive power transfer through a wall of the nuclear material storage container. The power received by the inductive power receiver can be used to power one or more sensors included in the device. Thus, the device is not required to include active power generation components such as, for example, a battery, that increase the risk of a spark igniting flammable gases within the container.

  14. Nekton Interaction Monitoring System

    Energy Technology Data Exchange (ETDEWEB)

    2017-03-15

    The software provides a real-time processing system for sonar to detect and track animals, and to extract water column biomass statistics in order to facilitate continuous monitoring of an underwater environment. The Nekton Interaction Monitoring System (NIMS) extracts and archives tracking and backscatter statistics data from a real-time stream of data from a sonar device. NIMS also sends real-time tracking messages over the network that can be used by other systems to generate other metrics or to trigger instruments such as an optical video camera. A web-based user interface provides remote monitoring and control. NIMS currently supports three popular sonar devices: M3 multi-beam sonar (Kongsberg), EK60 split-beam echo-sounder (Simrad) and BlueView acoustic camera (Teledyne).

  15. Real-time monitoring and analyzing system for transient power quality%暂态电能质量实时监测和分析系统

    Institute of Scientific and Technical Information of China (English)

    冯浩; 谢盛平; 郑贺伟

    2011-01-01

    一套完整的电能质量监测装置要求能够同时对各种稳态和暂态电能质量信号进行实时监测和分析,而现有的监测装置仅有少数具有暂态监测和分析功能,且只涉及到电压暂降、电压暂升和短时电压中断这3种扰动信号.为了对目前各种常见暂态电能质量扰动信号进行实时监测和分析,提出了一种以移动离散小波变换算法为核心,虚拟仪器为平台的设计方案,所设计出的系统可以根据用户的需要实现在线和离线分析,能够实时地检测到常见暂态电能质量扰动信号的多个参数指标,同时能够对扰动信号进行准确而又快速的分类.最后,通过实验验证了该系统的实用性和可靠性.%A set of integrated power quality monitoring equipment needs real-time monitor and analyze both steady and transient power quality signals, however, only a little of existing monitoring equipment has the real-time transient monitoring and analyzing function,involving just three disturbance signals: voltage sag, voltage swell and momentary voltage interruption. In order to monitor and analyze all kinds of common transient power quality disturbance signals,a design proposal based on the running discrete wavelet transform and virtual instrument is proposed. The system can achieve on-line and off-line analysis depending on the user's requirement, with the function of detecting multiple index of the transient disturbance signals accurately,and classifying them automatically with high accuracy and speed. Finally,experiment results demonstrate the good practicability and reliability of the system.

  16. Radiation monitoring system

    Energy Technology Data Exchange (ETDEWEB)

    Aghina, Mauricio A.C.; Farias, Marcos S. de; Lacerda, Fabio de; Heimlich, Adino [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    Design of a portable low-power multichannel analyzer with wireless connectivity for remote radiation monitoring, powered from a solar panel with a internal battery to be operated in field. The multichannel analyzer is based on a single microcontroller which performs the digital functions and an analog signal processing board for implementing a Gaussian shaper preamplifier, a Gaussian stretcher, sample and hold, pile-up rejector and a 10 bit ADC. Now this design is to be used with a NaI(Ti) scintillator detector. This multichannel analyzer is designed to be a part of radiation monitoring network. All of them are connected, by radio in a radius of 10 kilometers, to a supervisor computer that collects data from the network of multichannel analyzers and numerically display the latest radiation measurements or graphically display measurements over time for all multichannel analyzers. Like: dose rate, spectra and operational status. Software also supports remotely configuring operating parameters (such as radiation alarm level) for each monitor independently. (author)

  17. Study of Power Quality Monitoring System of Rural Power Grid Based on DSP + ARM%基于DSP+ARM的农村电网电能质量监测系统研究

    Institute of Scientific and Technical Information of China (English)

    杜娟; 张瑾; 刘冰; 许青松

    2011-01-01

    针对农村电网电能质量问题,设计以DSP和ARM为核心的嵌入式系统来检测农村电网的电能质量.在嵌入式Linux操作系统的软件平台上,通过QT/Embedded实现良好的人机交互界面,以TMS320VC5416数据处理器、Samsung公司的S3C2410为硬件核心,以SPI实现DSP与ARM的串口通信,并利用希尔伯特-黄变换(HHT)算法对农村电能质量进行检测,大大提高了对农村电网的用电质量监测能力,同时也为农村电网的重建和改造提供了重要依据.%According to rural power grid power quality problems, the embedded system centered on DSP and ARM is designed to detect rural power grid power quality. In the embedded Linux operating system software platform through the QT/Embedded, the friendly man-machine interface is realized, Taking TMS320VC5416 data processor and Samsung S3C2410 as the hardware core, SPI is used to achieve DSP and ARM serial port communication, and the Hilbert-Huang transform ( HHT) algorithm is used to detect the rural power grid power quality. It has greatly increased the capability of rural power grid power quality monitoring while providing an important basis for the reconstruction of rural power grid.

  18. Power Systems integration

    Science.gov (United States)

    Brantley, L. W.

    1982-01-01

    Power systems integration in large flexible space structures is discussed with emphasis upon body control. A solar array is discussed as a typical example of spacecraft configuration problems. Information on how electric batteries dominate life-cycle costs is presented in chart form. Information is given on liquid metal droplet generators and collectors, hot spot analysis, power dissipation in solar arrays, solar array protection optimization, and electromagnetic compatibility for a power system platform.

  19. User guide to power management for PCs and monitors

    Energy Technology Data Exchange (ETDEWEB)

    Nordman, B.; Piette, M.A.; Kinney, K.; Webber, C. [Lawrence Berkeley National Lab., CA (United States). Environmental Energy Technologies Div.

    1997-01-01

    Power management of personal computers (PCs) and monitors has the potential to save significant amounts of electricity as well as deliver other economic and environmental benefits. The Environmental Protection Agency`s ENERGY STAR{reg_sign} program has transformed the PC market so that equipment capable of power management is now widely available. However, previous studies have found that many Energy Star compliant computer systems are not accomplishing energy savings. The principal reasons for this are systems not being enabled for power management or a circumstance that prevents power management from operating. This guide is intended to provide information to computer support workers to increase the portion of systems that successfully power manage. The guide introduces power management concepts and the variety of benefits that power management can bring. It then explains how the parts of a computer system work together to enter and leave power management states. Several common computer system types are addressed, as well as the complications that networks bring to power management. Detailed instructions for checking and configuring several system types are provided, along with trouble shooting advice. The guide concludes with a discussion of how to purchase Energy Star compliant systems and future directions for power management of PCs and related equipment.

  20. User guide to power management for PCs and monitors

    Energy Technology Data Exchange (ETDEWEB)

    Nordman, B.; Piette, M.A.; Kinney, K.; Webber, C. [Lawrence Berkeley National Lab., CA (United States). Environmental Energy Technologies Div.

    1997-01-01

    Power management of personal computers (PCs) and monitors has the potential to save significant amounts of electricity as well as deliver other economic and environmental benefits. The Environmental Protection Agency`s ENERGY STAR{reg_sign} program has transformed the PC market so that equipment capable of power management is now widely available. However, previous studies have found that many Energy Star compliant computer systems are not accomplishing energy savings. The principal reasons for this are systems not being enabled for power management or a circumstance that prevents power management from operating. This guide is intended to provide information to computer support workers to increase the portion of systems that successfully power manage. The guide introduces power management concepts and the variety of benefits that power management can bring. It then explains how the parts of a computer system work together to enter and leave power management states. Several common computer system types are addressed, as well as the complications that networks bring to power management. Detailed instructions for checking and configuring several system types are provided, along with trouble shooting advice. The guide concludes with a discussion of how to purchase Energy Star compliant systems and future directions for power management of PCs and related equipment.

  1. A real time status monitor for transistor bank driver power limit resistor in boost injection kicker power supply

    Energy Technology Data Exchange (ETDEWEB)

    Mi, J.; Tan, Y.; Zhang, W.

    2011-03-28

    For years suffering of Booster Injection Kicker transistor bank driver regulator troubleshooting, a new real time monitor system has been developed. A simple and floating circuit has been designed and tested. This circuit monitor system can monitor the driver regulator power limit resistor status in real time and warn machine operator if the power limit resistor changes values. This paper will mainly introduce the power supply and the new designed monitoring system. This real time resistor monitor circuit shows a useful method to monitor some critical parts in the booster pulse power supply. After two years accelerator operation, it shows that this monitor works well. Previously, we spent a lot of time in booster machine trouble shooting. We will reinstall all 4 PCB into Euro Card Standard Chassis when the power supply system will be updated.

  2. Vehicle chassis monitoring system

    Energy Technology Data Exchange (ETDEWEB)

    Pisu, P.; Soliman, A.; Rizzoni, G. [Ohio State Univ., Columbus (United States). Center for Automotive Research

    2001-07-01

    Fault detection and isolation is becoming one of the most important aspects in vehicle control system design. In order to achieve this FDI schemes, particular vehicle subsystems integrated with a controller have been proposed. This paper introduces a new model-based fault detection and fault diagnosis method for monitoring the vehicle chassis performance. (orig.)

  3. 风电场监控系统现状和发展趋势综述%Summary on the actuality and development trend of the wind power generation fields monitoring system

    Institute of Scientific and Technical Information of China (English)

    杨文华

    2011-01-01

    Based on the widely investigation for the integrative monitoring systems of internal and overseas wind power generation fields,analyzes the appearing background,network structure and function characteristic of the monitoring system in wind power generation fields,compares both of similarities and differences between internal and overseas monitoring system,discusses the development trend of the monitoring system in wind power generation fields.%对国内外风电场综合监控系统进行了广泛调研,分析了风电场监控系统的产生的背景、现状、组网方式及功能特点,比较了国内外监控系统的相同和异同,在此基础上讨论了风电场监控系统的发展趋势。

  4. Self-Powered WSN for Distributed Data Center Monitoring

    Directory of Open Access Journals (Sweden)

    Davide Brunelli

    2016-01-01

    Full Text Available Monitoring environmental parameters in data centers is gathering nowadays increasing attention from industry, due to the need of high energy efficiency of cloud services. We present the design and the characterization of an energy neutral embedded wireless system, prototyped to monitor perpetually environmental parameters in servers and racks. It is powered by an energy harvesting module based on Thermoelectric Generators, which converts the heat dissipation from the servers. Starting from the empirical characterization of the energy harvester, we present a power conditioning circuit optimized for the specific application. The whole system has been enhanced with several sensors. An ultra-low-power micro-controller stacked over the energy harvesting provides an efficient power management. Performance have been assessed and compared with the analytical model for validation.

  5. Self-Powered WSN for Distributed Data Center Monitoring

    Science.gov (United States)

    Brunelli, Davide; Passerone, Roberto; Rizzon, Luca; Rossi, Maurizio; Sartori, Davide

    2016-01-01

    Monitoring environmental parameters in data centers is gathering nowadays increasing attention from industry, due to the need of high energy efficiency of cloud services. We present the design and the characterization of an energy neutral embedded wireless system, prototyped to monitor perpetually environmental parameters in servers and racks. It is powered by an energy harvesting module based on Thermoelectric Generators, which converts the heat dissipation from the servers. Starting from the empirical characterization of the energy harvester, we present a power conditioning circuit optimized for the specific application. The whole system has been enhanced with several sensors. An ultra-low-power micro-controller stacked over the energy harvesting provides an efficient power management. Performance have been assessed and compared with the analytical model for validation. PMID:26729135

  6. Self-Powered WSN for Distributed Data Center Monitoring.

    Science.gov (United States)

    Brunelli, Davide; Passerone, Roberto; Rizzon, Luca; Rossi, Maurizio; Sartori, Davide

    2016-01-02

    Monitoring environmental parameters in data centers is gathering nowadays increasing attention from industry, due to the need of high energy efficiency of cloud services. We present the design and the characterization of an energy neutral embedded wireless system, prototyped to monitor perpetually environmental parameters in servers and racks. It is powered by an energy harvesting module based on Thermoelectric Generators, which converts the heat dissipation from the servers. Starting from the empirical characterization of the energy harvester, we present a power conditioning circuit optimized for the specific application. The whole system has been enhanced with several sensors. An ultra-low-power micro-controller stacked over the energy harvesting provides an efficient power management. Performance have been assessed and compared with the analytical model for validation.

  7. Inductive System Monitors Tasks

    Science.gov (United States)

    2008-01-01

    The Inductive Monitoring System (IMS) software developed at Ames Research Center uses artificial intelligence and data mining techniques to build system-monitoring knowledge bases from archived or simulated sensor data. This information is then used to detect unusual or anomalous behavior that may indicate an impending system failure. Currently helping analyze data from systems that help fly and maintain the space shuttle and the International Space Station (ISS), the IMS has also been employed by data classes are then used to build a monitoring knowledge base. In real time, IMS performs monitoring functions: determining and displaying the degree of deviation from nominal performance. IMS trend analyses can detect conditions that may indicate a failure or required system maintenance. The development of IMS was motivated by the difficulty of producing detailed diagnostic models of some system components due to complexity or unavailability of design information. Successful applications have ranged from real-time monitoring of aircraft engine and control systems to anomaly detection in space shuttle and ISS data. IMS was used on shuttle missions STS-121, STS-115, and STS-116 to search the Wing Leading Edge Impact Detection System (WLEIDS) data for signs of possible damaging impacts during launch. It independently verified findings of the WLEIDS Mission Evaluation Room (MER) analysts and indicated additional points of interest that were subsequently investigated by the MER team. In support of the Exploration Systems Mission Directorate, IMS is being deployed as an anomaly detection tool on ISS mission control consoles in the Johnson Space Center Mission Operations Directorate. IMS has been trained to detect faults in the ISS Control Moment Gyroscope (CMG) systems. In laboratory tests, it has already detected several minor anomalies in real-time CMG data. When tested on archived data, IMS was able to detect precursors of the CMG1 failure nearly 15 hours in advance of

  8. Power Electronics System Communications

    OpenAIRE

    Milosavljevic, Ivana

    1999-01-01

    This work investigates communication issues in high-frequency power converters. A novel control communication network (Power Electronics System Network or PES Net) is proposed for modular, medium and high-power, converters. The network protocol, hardware and software are designed and implemented. The PES Net runs at 125 Mb/s over plastic optical fiber allowing converter switching frequencies in excess of 100 kHz. Communication control is implemented in a fie...

  9. CERN GSM monitoring system

    CERN Multimedia

    Ghabrous Larrea, C

    2009-01-01

    As a result of the tremendous development of GSM services over the last years, the number of related services used by organizations has drastically increased. Therefore, monitoring GSM services is becoming a business critical issue in order to be able to react appropriately in case of incident. In order to provide with GSM coverage all the CERN underground facilities, more than 50 km of leaky feeder cable have been deployed. This infrastructure is also used to propagate VHF radio signals for the CERN’s fire brigade. Even though CERN’s mobile operator monitors the network, it cannot guarantee the availability of GSM services, and for sure not VHF services, where signals are carried by the leaky feeder cable. So, a global monitoring system has become critical to CERN. In addition, monitoring this infrastructure will allow to characterize its behaviour over time, especially with LHC operation. Given that commercial solutions were not yet mature, CERN developed a system based on GSM probes and an application...

  10. 基于物联网的光伏发电智能监控系统%Photovoltaic Power Generation Intelligent Monitoring System Based on Internet of Things

    Institute of Scientific and Technical Information of China (English)

    梁新田; 徐志华

    2015-01-01

    搭建基于物联网的区域光伏发电系统的智能监控平台。以光伏发电系统故障检测算法和设备的优化管理为基础,通过建立性能评估模型,实现对区域分布式光伏发电系统的安全运行性能进行评估。运行结果表明,系统数据传输效果好、性能稳定可靠,具有很高的应用和推广价值。%This paper built an intelligent monitoring system of integrated photovoltaic power generation based onInternet of Things.Based on the fault detection algorithm and the optimal management of devices,the evaluation modelwas built to evaluate the operation performances of regional distributed photovoltaic power generation system.The testresults show that the system has the effective data transmission,reliable and steady performances,which has highapplication and promotion value.

  11. 电力变压器无线温度监测系统的研究%Study on wireless temperature monitoring system of power transformer

    Institute of Scientific and Technical Information of China (English)

    陈国庆

    2012-01-01

    我国变配电用变压器数量众多、分布广泛,充分利用现有的无线电通讯技术、以太网等监测技术、可以构建一个安全可靠的变压器无线温度监测网.本文介绍了在配电变压器上安装无线温度监测系统,通过实时监测变压器的温度变化情况,及时发现变压器存在的缺陷或发生故障的位置,并通过中短距离无线网络转发方式,将信号传递至以太网,彻底解决现场监测配电变压器参数的困难,从而实现变压器数据的实时采集和传输,实现区域内乃至全国性的变配电变压器信息的汇集与监测体系.%The transformer for electricity transformation and distribution has a great quantity and has been widely used in China. By fully applying the existing monitoring technologies like radio communication and Ethernet, a safe and reliable wireless temperature monitoring network of transformer can be established. In this paper, the installation of wireless temperature monitoring system on transformer for power distribution was introduced. By monitoring the temperature variations in real time, it could find the existing defects or error position of transformer in time, and by the forwarding way of wireless communication in medium and short distance, the signals can be transferred to the Ethernet. It can solve the difficulty on field monitoring of transformer parameters, so as to realize the real - time collection and transmission, and establish the regional and nationwide influx and monitor system of information of transformer for electricity transformation and distribution.

  12. The assessment of external photon dose rate in the vicinity of nuclear power stations. An intercomparison of different monitoring systems

    DEFF Research Database (Denmark)

    Thompson, I.M.G.; Bøtter-Jensen, L.; Lauterbach, U.

    1993-01-01

    to a nuclear power station. The responses of each of these detectors to the natural radiation and to the radiation from the power station are given. Estimations by three of the dose rate instruments of the air kerma from all the radiation components are intercompared with the results from three different types...... of thermoluminescence dosemeter. The results clearly demonstrate that accurate estimations of doses in the environment arising from a nuclear facility can only be obtained if the responses of the detectors used to the different radiation components at that location are accurately evaluated. By correcting the measured...

  13. Prognostics and Health Monitoring of High Power LED

    Directory of Open Access Journals (Sweden)

    Chris Bailey

    2012-02-01

    Full Text Available Prognostics is seen as a key component of health usage monitoring systems, where prognostics algorithms can both detect anomalies in the behavior/performance of a micro-device/system, and predict its remaining useful life when subjected to monitored operational and environmental conditions. Light Emitting Diodes (LEDs are optoelectronic micro-devices that are now replacing traditional incandescent and fluorescent lighting, as they have many advantages including higher reliability, greater energy efficiency, long life time and faster switching speed. For some LED applications there is a requirement to monitor the health of LED lighting systems and predict when failure is likely to occur. This is very important in the case of safety critical and emergency applications. This paper provides both experimental and theoretical results that demonstrate the use of prognostics and health monitoring techniques for high power LEDs subjected to harsh operating conditions.

  14. Faults and Diagnosis Systems in Power Converters

    DEFF Research Database (Denmark)

    Lee, Kyo-Beum; Choi, Uimin

    2014-01-01

    efforts have been put into making these systems better in terms of reliability in order to achieve high power source availability, reduce the cost of energy and also increase the reliability of overall systems. Among the components used in power converters, a power device and a capacitor fault occurs most......A power converter is needed in almost all kinds of renewable energy systems and drive systems. It is used both for controlling the renewable source and for interfacing with the load, which can be grid-connected or working in standalone mode. Further, it drives the motors efficiently. Increasing...... frequently. Therefore, it is important to monitor the power device and capacitor fault to increase the reliability of power electronics. In this chapter, the diagnosis methods for power device fault will be discussed by dividing into open- and short-circuit faults. Then, the condition monitoring methods...

  15. Earth System Monitoring, Introduction

    Science.gov (United States)

    Orcutt, John

    This section provides sensing and data collection methodologies, as well as an understanding of Earth's climate parameters and natural and man-made phenomena, to support a scientific assessment of the Earth system as a whole, and its response to natural and human-induced changes. The coverage ranges from climate change factors and extreme weather and fires to oil spill tracking and volcanic eruptions. This serves as a basis to enable improved prediction and response to climate change, weather, and natural hazards as well as dissemination of the data and conclusions. The data collection systems include satellite remote sensing, aerial surveys, and land- and ocean-based monitoring stations. Our objective in this treatise is to provide a significant portion of the scientific and engineering basis of Earth system monitoring and to provide this in 17 detailed articles or chapters written at a level for use by university students through practicing professionals. The reader is also directed to the closely related sections on Ecological Systems, Introduction and also Climate Change Modeling Methodology, Introduction as well as Climate Change Remediation, Introduction to. For ease of use by students, each article begins with a glossary of terms, while at an average length of 25 print pages each, sufficient detail is presented for use by professionals in government, universities, and industries. The chapters are individually summarized below.

  16. Wind power in modern power systems

    DEFF Research Database (Denmark)

    Chen, Zhe

    2013-01-01

    In recent years, wind power is experiencing a rapid growth, and large-scale wind turbines/wind farms have been developed and connected to power systems. However, the traditional power system generation units are centralized located synchronous generators with different characteristics compared...... with wind turbines. This paper presents an overview of the issues about integrating large-scale wind power plants into modern power systems. Firstly, grid codes are introduced. Then, the main technical problems and challenges are presented. Finally, some possible technical solutions are discussed....

  17. Power Systems Development Facility

    Energy Technology Data Exchange (ETDEWEB)

    Southern Company Services

    2009-01-31

    In support of technology development to utilize coal for efficient, affordable, and environmentally clean power generation, the Power Systems Development Facility (PSDF), located in Wilsonville, Alabama, has routinely demonstrated gasification technologies using various types of coals. The PSDF is an engineering scale demonstration of key features of advanced coal-fired power systems, including a Transport Gasifier, a hot gas particulate control device, advanced syngas cleanup systems, and high-pressure solids handling systems. This final report summarizes the results of the technology development work conducted at the PSDF through January 31, 2009. Twenty-one major gasification test campaigns were completed, for a total of more than 11,000 hours of gasification operation. This operational experience has led to significant advancements in gasification technologies.

  18. An Initial Survey of Fire Prevention and Monitoring in Power Systems%新型变电站火灾监测技术之探讨

    Institute of Scientific and Technical Information of China (English)

    杜燕平

    2012-01-01

    对具有强电磁干扰的变电站的火灾隐患进行预防和监测,多年来人们一直在探讨,如单独利用传统的电子传感器或采用新型的光纤光栅温度传感系统来实施远程监控,但由于传输导线的绝缘性能不稳定、光纤光栅传感器的成本较高、施工工艺复杂,故不能在电力火灾的监控中广泛采用.通过对烟雾火灾报警与光纤光栅测温相结合的探讨,不仅能对变电站的关键热点实施实时监测,而且还能对电力系统进行宏观监控以预防电力火灾.%In the electrical power system some spots have the strong electromagnetic interference and terrible envi- ronment. Traditional electronic sensors require metal wire for signal transmission. For it is unable to guarantee its transmission, the wire has reliable also stable insulating ability in the high voltage environment, thus it is unable to realize the online precision measurement. New fiber Bragg grating temperature sensor system is able to achieve real - time remote monitoring of the electricity system febrile node. However, due to the higher cost of fiber Bragg grat- ing sensors, and complex construction process, it is not suitable for substation fire monitoring. We combine the smoke/ire alarm system and fiber Bragg grating temperature system, and then achieve not only real -time monito- ring of key hot spots of the substation and the elimination of fire hazards, but also macro monitoring of substation and increase of the reliability of the system.

  19. 电力安全风险现场监控系统的设计%Research and Design of Power Security Risk on Site Monitoring System

    Institute of Scientific and Technical Information of China (English)

    李琳; 杨涛; 栗庆吉

    2013-01-01

    In light of the better mobility and flexibility of the mobile terminal, this paper proposes a design of Android-based power se-curity risk on site monitoring system. With this software, users can view and operate the instructions during the operation in real-time, monitor and record the information of the job sites, to achieve the assessment, warning and containment of the full state of standardized job security risk. And it comprehensively improves the level of standardization of operating risk containment.%基于移动终端具有移动性、灵活性等优点,提出一种基于Android的电力安全风险现场监控系统。应用该软件系统,用户可在作业过程中对指导书进行实时查看与操作,对作业现场进行实时监控与记录,实现标准化作业安全风险全程实时评估、预警和控制,全面提高标准化作业风险防控水平。

  20. SUNIST Microwave Power System

    Institute of Scientific and Technical Information of China (English)

    Feng Songlin; Yang Xuanzong; Feng Chunhua; Wang Long; Rao Jun; Feng Kecheng

    2005-01-01

    Experiments on the start-up and formation of spherical tokamak plasmas by electron cyclotron heating alone without ohmic heating and electrode discharge assisted electron cyclotron wave current start-up will be carried out on the SUNIST (Sino United Spherical Tokamak) device.The 2.45 GHz/100 kW/30 ms microwave power system and 1000 V/50 A power supply for electrode discharge are ready for experiments with non-inductive current drive.

  1. The Danish Marine Monitoring System

    DEFF Research Database (Denmark)

    Ærtebjerg, G.

    1997-01-01

    Indeholder abstracts fra Workshop on Marine Monitoring Systems and Technology, Risø, 17-18 April 1996.......Indeholder abstracts fra Workshop on Marine Monitoring Systems and Technology, Risø, 17-18 April 1996....

  2. Configuration of Risk Monitor System by PLant Defense-In.Depth Monitor and Relability Monitor

    DEFF Research Database (Denmark)

    Yoshikawa, Hidekazu; Lind, Morten; Yang, Ming;

    2012-01-01

    A new method of risk monitor system of a nuclear power plant has been proposed from the aspect by what degree of safety functions incorporated in the plant system is maintained by multiple barriers of defense-in-depth (DiD). Wherein, the central idea is plant DiD risk monitor and reliability...... monitor derived from the four aspects of (i) design principle of nuclear safety to realize DiD concept, (ii) definition of risk and risk to be monitored, (iii) severe accident phenomena as major risk, (iv) scheme of risk ranking, and (v) dynamic risk display. In this paper, the overall frame...... of the proposed frame on risk monitor system is summarized and the detailed discussion is made on the definitions of major terminologies of risk, risk ranking, anatomy of fault occurrence, two-layer configuration of risk monitor, how to configure individual elements of plant DiD risk monitor and its example...

  3. Submerged Medium Voltage Cable Systems at Nuclear Power Plants. A Review of Research Efforts Relevant to Aging Mechanisms and Condition Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Jason [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bernstein, Robert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); White, II, Gregory Von [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Glover, Steven F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Neely, Jason C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Pena, Gary [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Williamson, Kenneth Martin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Zutavern, Fred J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gelbard, Fred [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-03-01

    and industrial literature was performed to identify : 1) findings regarding the degradation mechanisms of submerged cabling and 2) condition monitoring methods that may prove useful in predict ing the remaining lifetime of submerged medium voltage p ower cables . The re search was conducted by a multi - disciplinary team , and s ources includ ed official NRC reports, n ational l aboratory reports , IEEE standards, conference and journal proceedings , magazine articles , PhD dissertations , and discussions with experts . The purpose of this work was to establish the current state - of - the - art in material degradation modeling and cable condition monitoring techniques and to identify research gaps . Subsequently, future areas of focus are recommended to address these research gaps and thus strengthen the efficacy of the NRC's developing cable condition monitoring program . Results of this literature review and details of the test ing recommendations are presented in this report . FOREWORD To ensure the safe, re liable, and cost - effective long - term operation of nuclear power plants, many systems, structures, and components must be continuously evaluated. The Nuclear Regulatory Commission (NRC) has identified that cables in submerged environments are of concern, particularly as plants are seeking license renewal. To date, there is a lack of consensus on aging and degradation mechanisms even though the area of submerged cables has been extensively studied. Consequently, the ability to make lifetime predictions for submerged cable does not yet exist. The NRC has engaged Sandia National Laboratories (SNL) to lead a coordinated effort to help elucidate the aging and degradation of cables in submerged environments by collaborating with cable manufacturers, utilities, universities, and other government agencies. A team of SNL experts was assembled from the laboratories including electrical condition monitoring, mat erial science, polymer degradation, plasma physics

  4. Electrical power distribution control methods, electrical energy demand monitoring methods, and power management devices

    Science.gov (United States)

    Chassin, David P.; Donnelly, Matthew K.; Dagle, Jeffery E.

    2006-12-12

    Electrical power distribution control methods, electrical energy demand monitoring methods, and power management devices are described. In one aspect, an electrical power distribution control method includes providing electrical energy from an electrical power distribution system, applying the electrical energy to a load, providing a plurality of different values for a threshold at a plurality of moments in time and corresponding to an electrical characteristic of the electrical energy, and adjusting an amount of the electrical energy applied to the load responsive to an electrical characteristic of the electrical energy triggering one of the values of the threshold at the respective moment in time.

  5. Development and installation of a new monitoring system for piping systems in fossil fired power plants; Entwicklung und Einsatz eines modernen Rohrleitungsueberwachungssystems fuer fossil befeuerte Kraftwerke

    Energy Technology Data Exchange (ETDEWEB)

    Maile, K. [Staatliche Materialpruefungsanstsalt (MPA), Stuttgart (Germany); Purper, H. [Staatliche Materialpruefungsanstsalt (MPA), Stuttgart (Germany); Rohler, K. [Deutsche Babcock Werke AG, Oberhausen (Germany); Wilson, B. [Babcock Energy Ltd., Renfrew (United Kingdom); Lehmann, H. [Rheinisch-Westfaelischer TUEV, Essen (Germany); Garcia, G. [Empresarios Agrupados, Madrid (Spain); Fernandez, J. [Union Fenosa, Madrid (Spain)

    1994-12-31

    The aim of the project was to produce a calculation method, instrumentation/measurement system and computer algorithms. The research was intended to increase the performance of life limiting components and systems operating at elevated temperatures. The detailed objectives of the project were specified as: 1. To evaluate elastic and inelastic stresses and strains and to assess creep and fatigue damage due to internal pressure, thermal transients and external loads - including dynamic loads - by advanced methods. 2. to determine highly loaded areas of components and systems by a new parametric calculation method and to optimise the load distribution on the components and systems for relevant operating conditions by that new method. 3. to determine thermal stresses in thick walled components by measuring temperatures on the outer surface of the component 4. to determine lifetime-relevant external loads by measuring important variables in systems by new methods and to take action if the measured results are out of specification 5. to record cumulative creep/fatigue damage and to estimate the remanent lifetime of the selected highly loaded areas of components and systems by new advanced lifetime monitoring systems. (orig.)

  6. New Passive Methodology for Power Cable Monitoring and Fault Location

    Science.gov (United States)

    Kim, Youngdeug

    The utilization of power cables is increasing with the development of renewable energy and the maintenance replacement of old overhead power lines. Therefore, effective monitoring and accurate fault location for power cables are very important for the sake of a stable power supply. The recent technologies for power cable diagnosis and temperature monitoring system are described including their intrinsic limitations for cable health assessment. Power cable fault location methods are reviewed with two main categories: off-line and on-line data based methods. As a diagnostic and fault location approach, a new passive methodology is introduced. This methodology is based on analyzing the resonant frequencies of the transfer function between the input and output of the power cable system. The equivalent pi model is applied to the resonant frequency calculation for the selected underground power cable transmission system. The characteristics of the resonant frequencies are studied by analytical derivations and PSCAD simulations. It is found that the variation of load magnitudes and change of positive power factors (i.e., inductive loads) do not affect resonant frequencies significantly, but there is considerable movement of resonant frequencies under change of negative power factors (i.e., capacitive loads). Power cable fault conditions introduce new resonant frequencies in accordance with fault positions. Similar behaviors of the resonant frequencies are shown in a transformer (TR) connected power cable system with frequency shifts caused by the TR impedance. The resonant frequencies can be extracted by frequency analysis of power signals and the inherent noise in these signals plays a key role to measure the resonant frequencies. Window functions provide an effective tool for improving resonant frequency discernment. The frequency analysis is implemented on noise laden PSCAD simulation signals and it reveals identical resonant frequency characteristics with theoretical

  7. Advanced targeted monitoring of high temperature components in power plants

    Energy Technology Data Exchange (ETDEWEB)

    Roos, E.; Maile, K.; Jovanovic, A. [MPA Stuttgart (Germany)

    1998-12-31

    The article presents the idea of targeted monitoring of high-temperature pressurized components in fossil-fueled power plants, implemented within a modular software system and using, in addition to pressure and temperature data, also displacement and strain measurement data. The concept has been implemented as a part of a more complex company-oriented Internet/Intranet system of MPA Stuttgart (ALIAS). ALIAS enables to combine smoothly the monitoring results with those of the off-line analysis, e. g. sensitivity analyses, comparison with preceding experience (case studies), literature search, search in material databases -(experimental and standard data), nonlinear FE-analysis, etc. The concept and the system have been implemented in real plant conditions several power plants in Germany and Europe: one of these applications and its results are described more in detail in the presentation. (orig.) 9 refs.

  8. Wireless system for location of permanent faults by short circuit current monitoring in electric power distribution network; Sistema wireless para localizacao de faltas permanentes atraves da monitoracao da corrente de curto-circuito em redes de distribuicao de energia eletrica

    Energy Technology Data Exchange (ETDEWEB)

    Machado, A.G.; Correa, A.C.; Machado, R.N. das M.; Ferreira, A.M.D.; Pinto, J.A.C. [Instituto Federal de Educacao, Ciencia e Tecnologia do Para (IFPA), Belem, PA (Brazil)], E-mail: alcidesmachado000@yahoo.com.br; Barra Junior, W. [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Inst. de Tecnologia. Faculdade de Engenharia Eletrica], E-mail: walbarra@ufpa.br

    2009-07-01

    This paper presents the development of an automatic system for permanent short-circuits location in medium voltage (13.8 kV) electric power system distribution feeders, by indirect monitoring of the line current. When a permanent failure occurs, the developed system uses mobile telephony (GSM) text messages (SMS) to inform the power company operation center where the failure most likely took place. With this information in real time, the power company operation center may provide the network restoration in a faster and efficient way. (author)

  9. Power Monitoring Using the Raspberry Pi

    Science.gov (United States)

    Snyder, Robin M.

    2014-01-01

    The Raspberry Pi is a credit card size low powered compute board with Ethernet connection, HDMI video output, audio, full Linux operating system run from an SD card, and more, all for $45. With cables, SD card, etc., the cost is about $70. Originally designed to help teach computer science principles to low income children and students, the Pi has…

  10. Systems and methods for an integrated electrical sub-system powered by wind energy

    Science.gov (United States)

    Liu, Yan; Garces, Luis Jose

    2008-06-24

    Various embodiments relate to systems and methods related to an integrated electrically-powered sub-system and wind power system including a wind power source, an electrically-powered sub-system coupled to and at least partially powered by the wind power source, the electrically-powered sub-system being coupled to the wind power source through power converters, and a supervisory controller coupled to the wind power source and the electrically-powered sub-system to monitor and manage the integrated electrically-powered sub-system and wind power system.

  11. Holistic data analysis at the condition monitoring of wind power plants; Gesamtheitliche Datenanalyse beim Condition Monitoring von Windenergieanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Brenner, Daniel; Tilch, Dietmar [Bosch Rexroth Monitoring Systems GmbH, Dresden (Germany)

    2013-06-01

    First of all, the holistic condition monitoring implies a combination of various sources of information. Currently, there are different systems of condition monitoring of single components at wind power plants. Furthermore, there are various sensors being integrated into the SCADA system. This requires a handling with different solutions as well as control rooms and thus with increased training costs, enhanced personnel costs and enhanced system costs. DMT GmbH (Essen, Federal Republic of Germany) and Bosch Rexroth Monitoring Systems GmbH (Dresden, Federal Republic of Germany) show how a solution can be created by means of a rotor blade monitoring system BLADEcontrol as well as the power train monitoring system Windsafe. This solution enables a combined analysis and is open to other monitoring systems under a unified user interface.

  12. Design and Retrofit of Radiation Monitoring System for the PWR Nuclear Power Plant%压水堆核电厂辐射监测系统的设计与改造

    Institute of Scientific and Technical Information of China (English)

    张涛; 熊国华; 郎玉凯; 郭伟

    2011-01-01

    辐射监测系统是压水堆核电厂安全运行的重要保障,研究压水堆核电厂辐射监测系统的设计方法和原则,对于提高压水堆核电厂辐射监测系统的设计水平,减少改造风险至关重要.根据核电厂的法规和设计规范,结合大亚湾核电厂辐射监测系统的设计与改造经验,提出了压水堆核电厂辐射监测系统的一般设计原则和要求,并简要介绍了大亚湾核电厂辐射监测系统的改造措施及方法.%Radiation monitoring system is important for the PWR nuclear power plant, and the research of design methods and principles for the radiation monitoring system can greatly improve the design ability of the system for PWR nuclear power plant, and reduce the risk of system retrofit. According to the Nuclear power plant regulations and design specifications, and taking the design and retrofit experience of the radiation monitoring system in Daya Bay Nuclear Power Plant into account, the general design principles and requirements of the radiation monitoring system in the PWR nuclear power plant is proposed, and the retrofit method of the radiation monitoring system in Daya Bay Nuclear Power Plant is briefly introduced.

  13. Monitoring and diagnosis of condensation systems in thermoelectric power stations: behavior indicators; Monitoreo y diagnostico de sistemas de condensacion en centrales termoelectricas: indicadores de comportamiento

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez Martinez, Hugo; Sanchez Sanchez, Ramon [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2009-07-01

    In this article are described the basic characteristics, capacities and benefits of a computer system for the monitoring and operation diagnosis of the main equipment of a condensation system of thermoelectric power plants. The system monitors the process variables in real time and, with base in these variables, it can realize a diagnosis of the cooling tower, the condenser, the circulation water and the circulating water pumps, deducting the possible problems (deficiency causes) and raising alternatives to improve the system performance or to solve the problem. It is important to mention that with base in the raised alternatives, the user can take decisions to diminish or eliminate the problem. The essential content of the article focuses in the description of the basic procedures for the calculation of the performance and diagnosis indicators of the condensation system of the equipment. The equipment evaluation is carried out by means of the comparison between the indicators values and the expected ones, whereas the diagnosis is realized by means of an expert system. [Spanish] En este articulo se describen las caracteristicas principales, capacidades y beneficios de un sistema computacional para el monitoreo y diagnostico del funcionamiento de los equipos principales de un sistema de condensacion de plantas termoelectricas. El sistema monitorea las variables del proceso en tiempo real y, con base en dichas variables, puede realizar un diagnostico de la torre de enfriamiento, el condensador y las bombas de agua de circulacion, deduciendo los posibles problemas (causas de las deficiencias) y planteando alternativas para mejorar el desempeno del sistema o solucionar el problema. Es importante mencionar que con base en las alternativas planteadas, el usuario puede tomar decisiones para reducir o eliminar el problema. El contenido esencial del articulo se enfoca en la descripcion de los procedimientos basicos para el calculo de los indicadores de desempeno y

  14. Solving the problems concerned with modernization of power unit monitoring and control systems using the distributed facilities and technologies available in the sargon computerized automation system. Part 1: Tools of PTC "sargon" for distributed systems

    Science.gov (United States)

    Mendelevich, V. A.

    2013-02-01

    The first part of this article describes the tools intended to construct distributed automated process control systems for the main thermal power equipment of power stations that are available in the SARGON computerized automation system.

  15. INSTALLATION OF A POST-ACCIDENT CONFINEMENT HIGH-LEVEL RADIATION MONITORING SYSTEM IN THE KOLA NUCLEAR POWER STATION (UNIT 2) IN RUSSIA

    Energy Technology Data Exchange (ETDEWEB)

    GREENE,G.A.; GUPPY,J.G.

    1998-09-01

    This is the final report on the INSP project entitled, ``Post-Accident Confinement High-Level Radiation Monitoring System'' conducted by BNL under the authorization of Project Work Plan WBS 1.2.2.6 (Attachment 1). This project was initiated in February 1993 to assist the Russians in reducing risks associated with the continued operation of older Soviet-designed nuclear power plants, specifically the Kola VVER-440/230 Unit 2, through improved accident detection capability, specifically by the installation of a dual train high-level radiation detection system in the confinement of Unit 2 of the Kola NPP. The major technical objective of this project was to provide, install and make operational the necessary hardware inside the confinement of the Kola NPP Unit 2 to provide early and reliable warning of the release of radionuclides from the reactor into the confinement air space as an indication of the occurrence of a severe accident at the plant. In addition, it was intended to provide hands-on experience and training to the Russian plant workers in the installation, operation, calibration and maintenance of the equipment in order that they may use the equipment without continued US assistance as an effective measure to improve reactor safety at the plant.

  16. The electric power engineering handbook power systems

    CERN Document Server

    2012-01-01

    Power Systems, Third Edition (part of the five-volume set, The Electric Power Engineering Handbook) covers all aspects of power system protection, dynamics, stability, operation, and control. Under the editorial guidance of L.L. Grigsby, a respected and accomplished authority in power engineering, and section editors Andrew Hanson, Pritindra Chowdhuri, Gerry Sheble, and Mark Nelms, this carefully crafted reference includes substantial new and revised contributions from worldwide leaders in the field. This content provides convenient access to overviews and detailed information on a diverse arr

  17. Wireless power transfer system

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Hunter; Sealy, Kylee; Gilchrist, Aaron

    2016-02-23

    A system includes a first stage of an inductive power transfer system with an LCL load resonant converter with a switching section, an LCL tuning circuit, and a primary receiver pad. The IPT system includes a second stage with a secondary receiver pad, a secondary resonant circuit, a secondary rectification circuit, and a secondary decoupling converter. The secondary receiver pad connects to the secondary resonant circuit. The secondary resonant circuit connects to the secondary rectification circuit. The secondary rectification circuit connects to the secondary decoupling converter. The second stage connects to a load. The load includes an energy storage element. The second stage and load are located on a vehicle and the first stage is located at a fixed location. The primary receiver pad wirelessly transfers power to the secondary receiver pad across a gap when the vehicle positions the secondary receiver pad with respect to the primary receiver pad.

  18. Submerged Medium Voltage Cable Systems at Nuclear Power Plants. A Review of Research Efforts Relevant to Aging Mechanisms and Condition Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Jason [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bernstein, Robert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); White, II, Gregory Von [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Glover, Steven F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Neely, Jason C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Pena, Gary [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Williamson, Kenneth Martin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Zutavern, Fred J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gelbard, Fred [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-03-01

    and industrial literature was performed to identify : 1) findings regarding the degradation mechanisms of submerged cabling and 2) condition monitoring methods that may prove useful in predict ing the remaining lifetime of submerged medium voltage p ower cables . The re search was conducted by a multi - disciplinary team , and s ources includ ed official NRC reports, n ational l aboratory reports , IEEE standards, conference and journal proceedings , magazine articles , PhD dissertations , and discussions with experts . The purpose of this work was to establish the current state - of - the - art in material degradation modeling and cable condition monitoring techniques and to identify research gaps . Subsequently, future areas of focus are recommended to address these research gaps and thus strengthen the efficacy of the NRC's developing cable condition monitoring program . Results of this literature review and details of the test ing recommendations are presented in this report . FOREWORD To ensure the safe, re liable, and cost - effective long - term operation of nuclear power plants, many systems, structures, and components must be continuously evaluated. The Nuclear Regulatory Commission (NRC) has identified that cables in submerged environments are of concern, particularly as plants are seeking license renewal. To date, there is a lack of consensus on aging and degradation mechanisms even though the area of submerged cables has been extensively studied. Consequently, the ability to make lifetime predictions for submerged cable does not yet exist. The NRC has engaged Sandia National Laboratories (SNL) to lead a coordinated effort to help elucidate the aging and degradation of cables in submerged environments by collaborating with cable manufacturers, utilities, universities, and other government agencies. A team of SNL experts was assembled from the laboratories including electrical condition monitoring, mat erial science, polymer degradation, plasma physics

  19. Retrofitting automated process control systems at Ukrainian power stations

    Energy Technology Data Exchange (ETDEWEB)

    B.E. Simkin; V.S. Naumchik; B.D. Kozitskii (and others) [OAO L' vovORGRES, Lviv (Ukraine)

    2008-04-15

    Approaches and principles for retrofitting automated process control systems at Ukrainian power stations are considered. The results obtained from retrofitting the monitoring and control system of Unit 9 at the Burshtyn thermal power station are described.

  20. Analysis and design on control mode of reforming station computer monitoring system of hydroelectric power%水电厂计算机监控系统改造的控制模式分析与设计

    Institute of Scientific and Technical Information of China (English)

    陈诚; 胡丽娟

    2012-01-01

    This paper introduced how to complete the upgrade of hydroelectric power station computer monitoring system while meeting the requirements of production and equipment control in power grid scheduling and set control center.%介绍了如何在保证满足电网调度集控中心的生产、设备控制要求同时完成水电厂计算机监控系统升级改造。

  1. 水文监测系统电源故障分析与维修%Analysis and Maintenance of Power Breakdown in Hydrological Monitoring System

    Institute of Scientific and Technical Information of China (English)

    莫炳建

    2013-01-01

    水文监测系统电源常采用太阳能电池板充电、蓄电池储电的供电方式,但太阳能电池板受天气因素影响,容易使电源电压波动而造成系统部分遥测站工作异常。出现故障的主要原因是当蓄电池电压略高于额定值时,太阳充电控制器过放电保护功能动作,断开与遥测终端RTU连接,停止向RTU供电;当蓄电池电压略低于额定值时,对电源电压要求较高的发射模块、压力水位计、光电编码型水位计等电子仪器不工作,为此提出解决的办法:更换电池,更换太阳能充电控制器,加装直流稳压器。经过多个水文站的使用,效果很好。%The hydrological monitoring system often uses power supply in the mode of solar panel charging and battery storage. However, solar panel is easily affected by weather factors, which may cause telemetry system abnormal due to voltage fluctuations. The main reason for this breakdown is the activation of protection function. Because when the battery voltage is higher than its rating value, the over-discharge protection function of the solar charge controller will be activated, then disconnect with telemetry RTU, which will result in interruption of power supply. The lower battery voltage will also cause problem. When the battery voltage is lower than rating value, the transmitter module, pressure gauge, optical encoder water level meter and other electronic devices which have higher demand of the power supply voltage, will stop working. There is one proposed solution:replacing battery and solar charge controller, installing DC regulator. Through the use at many stations, it proves the effect is very good.

  2. Wind power plant system services

    DEFF Research Database (Denmark)

    Basit, Abdul; Altin, Müfit

    Traditionally, conventional power plants have the task to support the power system, by supplying power balancing services. These services are required by the power system operators in order to secure a safe and reliable operation of the power system. However, as in the future the wind power...... is going more and more to replace conventional power plants, the sources of conventional reserve available to the system will be reduced and fewer conventional plants will be available on-line to share the regulation burden. The reliable operation of highly wind power integrated power system might...... then beat risk unless the wind power plants (WPPs) are able to support and participate in power balancing services. The objective of this PhD project is to develop and analyse control strategies which can increase the WPPs capability to provide system services, such as active power balancing control...

  3. Balancing modern Power System with large scale of wind power

    OpenAIRE

    Basit, Abdul; Altin, Müfit; Hansen, Anca Daniela; Sørensen, Poul Ejnar

    2014-01-01

    Power system operators must ensure robust, secure and reliable power system operation even with a large scale integration of wind power. Electricity generated from the intermittent wind in large propor-tion may impact on the control of power system balance and thus deviations in the power system frequency in small or islanded power systems or tie line power flows in interconnected power systems. Therefore, the large scale integration of wind power into the power system strongly concerns the s...

  4. The development of power specific redlines for SSME safety monitoring

    Science.gov (United States)

    Maul, William A.; Bosch, Claudia M.

    1989-01-01

    Over the past several years, there has been an increased awareness in the necessity for rocket engine health monitoring because of the cost and complexity of present and future systems. A current rocket engine system, the Space Shuttle Main Engine (SSME), combines a limited redline system with closed-loop control of the engine's thrust level and mixture ratio. Despite these features, 27 tests of the SSME have resulted in major incidents. An SSME transient model was used to examine the effect of variations in high pressure turbopump performance on various engine parameters. Based on analysis of the responses, several new parameters are proposed for further investigation as power-level specific redlines.

  5. The ingestible thermal monitoring system

    Science.gov (United States)

    Cutchis, Protagoras N.; Hogrefe, Arthur F.; Lesho, Jeffery C.

    1988-01-01

    A thermal monitoring system for measuring body core temperatures was developed that contains an ingestible pill which is both commandable and rechargeable, and which uses magnetic induction for command and telemetry as well as for recharging. The pill electronics consist of a battery power source, a crystal-controlled oscillator that drives a small air coil, and a command detection circuit. The resulting 262-kHz magnetilc field can be easily detected from a distance of 1 m. The pill oscillator functions at voltages less than 1 V, supplied by a single Ni-Cd battery, which must be recharged after 72 h of continuous transmission. The pill can be recalibrated periodically to compensate for long-term drift.

  6. Tools for Distributed Systems Monitoring

    Directory of Open Access Journals (Sweden)

    Kufel Łukasz

    2016-11-01

    Full Text Available The management of distributed systems infrastructure requires dedicated set of tools. The one tool that helps visualize current operational state of all systems and notify when failure occurs is available within monitoring solution. This paper provides an overview of monitoring approaches for gathering data from distributed systems and what are the major factors to consider when choosing a monitoring solution. Finally we discuss the tools currently available on the market.

  7. ON COMPLEXITY OF POWER SYSTEMS

    Institute of Scientific and Technical Information of China (English)

    MA Jin; CHENG Daizhan; HONG Yiguang; SUN Yuanzhang

    2003-01-01

    The power system is a classical example of complex systems. In this paper it is shown that the power industry in China is facing a tremendous challenge. The complexity in power systems is investigated as follows. First, the cascade failure in power systems is analyzed, and compared with sand-pile model. Next, we show that the agent-based modelling is a proper way for power network. Mathematically, the geometric dynamics and differential inclusion are useful tools for the stability analysis of large scale power systems. As for power market, the game theory and generalized control system model are proposed. For a complex power system, an evolutive model may be more accurate in description and analysis. Finally, certain newly developed numerical methods in the power system computation are introduced. Overall, we are convinced that the theorem of complexity, combined with modern control theory, may be the right way to answer the challenges faced by the power industry in China.

  8. CERN Safety System Monitoring - SSM

    CERN Document Server

    Hakulinen, T; Valentini, F; Gonzalez, J; Salatko-Petryszcze, C

    2011-01-01

    CERN SSM (Safety System Monitoring) [1] is a system for monitoring state-of-health of the various access and safety systems of the CERN site and accelerator infrastructure. The emphasis of SSM is on the needs of maintenance and system operation with the aim of providing an independent and reliable verification path of the basic operational parameters of each system. Included are all network-connected devices, such as PLCs, servers, panel displays, operator posts, etc. The basic monitoring engine of SSM is a freely available system-monitoring framework Zabbix [2], on top of which a simplified traffic-light-type web-interface has been built. The web-interface of SSM is designed to be ultra-light to facilitate access from handheld devices over slow connections. The underlying Zabbix system offers history and notification mechanisms typical of advanced monitoring systems.

  9. Instrumentation for monitoring powered support behavior

    Energy Technology Data Exchange (ETDEWEB)

    Smart, B.G.D.; Sommerville, J. M.; McGraw, W.M.

    1987-06-01

    The parameters quantifying powered support performance can be efficiently gathered underground on working faces with an electronic data logger. The paper reports modifications to a British Coal/Rapco Data Logger, to existing analogue transducers, and the development of new transducers to enable various parameters to be logged and related to mining operations. The paper also reports on the management and interpretation of the logged data by a suite of computer programs developed around a P.C. workstation. Conclusions as to the suitability of the system are drawn and recommendations about future transducer development are made. 1 ref.

  10. Power Systems Development Facility

    Energy Technology Data Exchange (ETDEWEB)

    None

    2003-07-01

    This report discusses Test Campaign TC12 of the Kellogg Brown & Root, Inc. (KBR) Transport Gasifier train with a Siemens Westinghouse Power Corporation (SW) particle filter system at the Power Systems Development Facility (PSDF) located in Wilsonville, Alabama. The Transport Gasifier is an advanced circulating fluidized-bed reactor designed to operate as either a combustor or a gasifier using a particulate control device (PCD). While operating as a gasifier, either air or oxygen can be used as the oxidant. Test run TC12 began on May 16, 2003, with the startup of the main air compressor and the lighting of the gasifier start-up burner. The Transport Gasifier operated until May 24, 2003, when a scheduled outage occurred to allow maintenance crews to install the fuel cell test unit and modify the gas clean-up system. On June 18, 2003, the test run resumed when operations relit the start-up burner, and testing continued until the scheduled end of the run on July 14, 2003. TC12 had a total of 733 hours using Powder River Basin (PRB) subbituminous coal. Over the course of the entire test run, gasifier temperatures varied between 1,675 and 1,850 F at pressures from 130 to 210 psig.

  11. Power Systems Development Facility

    Energy Technology Data Exchange (ETDEWEB)

    None

    2003-07-01

    This report discusses Test Campaign TC12 of the Kellogg Brown & Root, Inc. (KBR) Transport Gasifier train with a Siemens Westinghouse Power Corporation (SW) particle filter system at the Power Systems Development Facility (PSDF) located in Wilsonville, Alabama. The Transport Gasifier is an advanced circulating fluidized-bed reactor designed to operate as either a combustor or a gasifier using a particulate control device (PCD). While operating as a gasifier, either air or oxygen can be used as the oxidant. Test run TC12 began on May 16, 2003, with the startup of the main air compressor and the lighting of the gasifier start-up burner. The Transport Gasifier operated until May 24, 2003, when a scheduled outage occurred to allow maintenance crews to install the fuel cell test unit and modify the gas clean-up system. On June 18, 2003, the test run resumed when operations relit the start-up burner, and testing continued until the scheduled end of the run on July 14, 2003. TC12 had a total of 733 hours using Powder River Basin (PRB) subbituminous coal. Over the course of the entire test run, gasifier temperatures varied between 1,675 and 1,850 F at pressures from 130 to 210 psig.

  12. Wind Powered Sprinkler System

    Directory of Open Access Journals (Sweden)

    Chin Jung Huang

    2013-06-01

    Full Text Available Due to limited energy resources, excessive emission of CO2, global warming, increase of mean temperature, serious impacts have resulted on our living environment, and thus, energy saving and carbon reduction have become urgent issues. Planting grass, flowers and trees can absorb and reduce CO2, thus meeting the requirements for energy saving and carbon reduction in environmental protection. At present, most of lawns or gardens in Taiwan are maintained by manual or traditional semiautomatic watering device. Whether the lawn needs to be watered and the amount of water to be sprinkled depends on subjective decision. When the lawn is watered without examining the moisture content of the soil beforehand, it causes waste of time, labor, water and cost. The intelligent wind powered watering system developed by this study used an electromechanical integrated design system to control the humidity probe, and used the electricity generated by natural wind power and pumping device to control the sprinkling action. This system sprinkles water by sensing the soil moisture content, and stops sprinkling automatically when the soil moisture content is enough, thus achieving the purposes of cost and energy saving.

  13. Smart Power Supply for Battery-Powered Systems

    Science.gov (United States)

    Krasowski, Michael J.; Greer, Lawrence; Prokop, Norman F.; Flatico, Joseph M.

    2010-01-01

    A power supply for battery-powered systems has been designed with an embedded controller that is capable of monitoring and maintaining batteries, charging hardware, while maintaining output power. The power supply is primarily designed for rovers and other remote science and engineering vehicles, but it can be used in any battery alone, or battery and charging source applications. The supply can function autonomously, or can be connected to a host processor through a serial communications link. It can be programmed a priori or on the fly to return current and voltage readings to a host. It has two output power busses: a constant 24-V direct current nominal bus, and a programmable bus for output from approximately 24 up to approximately 50 V. The programmable bus voltage level, and its output power limit, can be changed on the fly as well. The power supply also offers options to reduce the programmable bus to 24 V when the set power limit is reached, limiting output power in the case of a system fault detected in the system. The smart power supply is based on an embedded 8051-type single-chip microcontroller. This choice was made in that a credible progression to flight (radiation hard, high reliability) can be assumed as many 8051 processors or gate arrays capable of accepting 8051-type core presently exist and will continue to do so for some time. To solve the problem of centralized control, this innovation moves an embedded microcontroller to the power supply and assigns it the task of overseeing the operation and charging of the power supply assets. This embedded processor is connected to the application central processor via a serial data link such that the central processor can request updates of various parameters within the supply, such as battery current, bus voltage, remaining power in battery estimations, etc. This supply has a direct connection to the battery bus for common (quiescent) power application. Because components from multiple vendors may have

  14. 3G POWER GRID SYSTEM

    OpenAIRE

    Saiyad Tausif Ali *; Gaurav Pawar; Pragati Rathi; Mandar Pathak

    2016-01-01

    3G Power grid system is dual side stream of electricity and automated construct information and distributed advanced energy delivery network. In this 3G Power grid system avoided the thermal and hydro sources of energy. By using the solar power and wind power energy will generate electricity according with the condition of nature. 3G Power grid system provides the facility of generating as well as marketing of electricity not only for the producers but also for consumers. By using megabytes o...

  15. Locomotive monitoring system using wireless sensor networks

    CSIR Research Space (South Africa)

    Croucamp, PL

    2014-07-01

    Full Text Available Theft of cables used for powering a locomotive not only stops the train from functioning but also paralyzes the signalling and monitoring system. This means that information on certain locomotive's cannot be passed onto other locomotives which may...

  16. OpenSM Monitoring System

    Energy Technology Data Exchange (ETDEWEB)

    2015-04-17

    The OpenSM Monitoring System includes a collection of diagnostic and monitoring tools for use on Infiniband networks. The information this system gathers is obtained from a service, which in turn is obtained directly from the OpenSM subnet manager.

  17. Ecological Monitoring Information System (EMIS).

    Science.gov (United States)

    Fiene, Richard John; And Others

    A system for evaluating and monitoring child development projects, with possible computerization capabilities, was developed for the State of Pennsylvania in connection with 26 child development projects funded by the Appalachian Regional Commission. The Ecological Monitoring Information System (EMIS), provides a series of ecological measurement…

  18. 基于LabVIEW的飞机地面电源监控系统设计与实现%Design and implementation of aircraft ground power supply monitoring system based on LabVIEW

    Institute of Scientific and Technical Information of China (English)

    程绪刚; 邱智; 郝世勇

    2015-01-01

    Since the complex situation and different electricity demands of aircraft from ground power supply,the ground power supply system is affected. Traditional instruments couldn’t monitor the whole working process of ground power supply,to ensure high power quality and stable performance of the ground power supply,the aircraft ground power supply monitoring system based on LabVIEW software is designed. The ground power supply is monitored and recorded in real⁃time by the parameters of voltage,frequency,harmonic content and so on,the status of ground power supply is judged with reference standard,an effec⁃tive method is provided to maintain normal operation of the ground power supply and ensure the safety electricity of the aircraft.%当地面电源向飞机供电时,由于情况复杂及飞机的用电需求各不相同,从而对地面电源产生影响。传统的仪器仪表不能监测地面电源工作时的整个过程,为保证地面电源有较高的供电品质和稳定的性能,基于LabVIEW软件设计飞机地面电源监控系统。从电压、频率、谐波含量等多个方面对地面电源进行实时监控并记录,参照一定的标准,对地面电源的状态进行判断,为维护地面电源的正常工作及保证飞机的用电安全提供了更有效的方法。

  19. International experience feedback on fatigue monitoring systems for nuclear power plants; Le retour d`experience international des fatiguemetres des tranches nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    Morilhat, P. [Electricite de France (EDF), Direction des Etudes et Recherches, 92 - Clamart (France)

    1997-12-31

    From the very beginning of electro-nuclear programmes the need has become internationally obvious to develop systems aiming at automation and improvement of monitoring of the transients stressing the main mechanical components of nuclear units, by checking the conservativeness of the design no longer from a comparison of causes (temperature and pressure variations) but by directly assessing the results (stresses and linked damage). Prototypes of such systems have appeared since the middle of the 1980`s mainly in France, the USA and Germany, and manufacturing them has since continued. Several years of development and on site testing of prototypes of fatigue measuring devices designed by the R and D Direction have enabled contacts with the developers of similar systems to be established and, in some cases, comparisons to be made. The experience accumulated in the use of such systems, both in France and abroad from now on makes a first experience feedback possible. The fatigue measuring device concept is based on a succession of elementary modules which enable the information received from the unit to be processed, first in the form of transient counting (transient meters), then in the form of mechanical diagnosis (fatigue monitoring systems). Among the systems in operation some provide actually only the transient meter part while others link transient meters and fatigue meters (EDF, EPRI and MITSUBISHI systems and some versions of the SIEMENS system). Moreover, numerous systems require, in addition to unit operation instrumentation, specific instrumentation located in monitored areas. The number of devices in operation has not stopped growing since the middle of the 80`s to reach 53 systems working in 1996. The biggest developers are EPRI and its consultant Structural Integrity Associates (FatiguePro system), SIEMENS (FAMOS system) and EDF whose gradual implementation of SYSFAC from `96 is going to make its share particularly increase. Technical experience feedback

  20. Arduino Based Infant Monitoring System

    Science.gov (United States)

    Farhanah Mohamad Ishak, Daing Noor; Jamil, Muhammad Mahadi Abdul; Ambar, Radzi

    2017-08-01

    This paper proposes a system for monitoring infant in an incubator and records the relevant data into a computer. The data recorded by the system can be further referred by the neonatal intensive care unit (NICU) personnel for diagnostic or research purposes. The study focuses on designing the monitoring system that consists of an incubator equipped with humidity sensor to measure the humidity level, and a pulse sensor that can be attached on an infant placed inside the incubator to monitor infant’s heart pulse. The measurement results which are the pulse rate and humidity level are sent to the PC via Arduino microcontroller. The advantage of this system will be that in the future, it may also enable doctors to closely monitor the infant condition through local area network and internet. This work is aimed as an example of an application that contributes towards remote tele-health monitoring system.

  1. Power Systems Development Facility

    Energy Technology Data Exchange (ETDEWEB)

    Southern Company Services

    2004-04-30

    This report discusses Test Campaign TC15 of the Kellogg Brown & Root, Inc. (KBR) Transport Gasifier train with a Siemens Power Generation, Inc. (SPG) particle filter system at the Power Systems Development Facility (PSDF) located in Wilsonville, Alabama. The Transport Gasifier is an advanced circulating fluidized-bed reactor designed to operate as either a combustor or gasifier using a particulate control device (PCD). While operating as a gasifier, either air or oxygen can be used as the oxidant. Test run TC15 began on April 19, 2004, with the startup of the main air compressor and the lighting of the gasifier startup burner. The Transport Gasifier was shutdown on April 29, 2004, accumulating 200 hours of operation using Powder River Basin (PRB) subbituminous coal. About 91 hours of the test run occurred during oxygen-blown operations. Another 6 hours of the test run was in enriched-air mode. The remainder of the test run, approximately 103 hours, took place during air-blown operations. The highest operating temperature in the gasifier mixing zone mostly varied from 1,800 to 1,850 F. The gasifier exit pressure ran between 200 and 230 psig during air-blown operations and between 110 and 150 psig in oxygen-enhanced air operations.

  2. 智能化电能质量监测、分析、管理系统的研究%Research of Intelligent Monitoring, Analysis and Management System of Power Quality

    Institute of Scientific and Technical Information of China (English)

    张鹏飞

    2012-01-01

    The paper introduced an intelligent monitoring, analysis and management system of power quality, and focused on overall structure, software architecture and function modules of the system. The system can online monitor electricity consumption situation and power quality of substation real-timely, classify and process collected information automatically, and achieve functions of online and association analysis of power quality and emergency alarm, which provides a reference for power grid plan, power quality trend forecasting, event prediction, pollution control and resolution of power quality disputes.%介绍了一种智能化电能质量监测、分析、管理系统,重点研究了系统的总体结构、软件架构及各功能模块.该系统能够对变电站的用电情况和电能质量进行实时在线监测,自动对收集的资料进行分类处理,实现了对电能质量的在线分析及关联分析、应急报警等功能,为电网规划、电能质量趋势预测、事件预测、污染源治理以及电能质量纠纷的解决提供了参考依据.

  3. Real-time performance monitoring and management system

    Science.gov (United States)

    Budhraja, Vikram S.; Dyer, James D.; Martinez Morales, Carlos A.

    2007-06-19

    A real-time performance monitoring system for monitoring an electric power grid. The electric power grid has a plurality of grid portions, each grid portion corresponding to one of a plurality of control areas. The real-time performance monitoring system includes a monitor computer for monitoring at least one of reliability metrics, generation metrics, transmission metrics, suppliers metrics, grid infrastructure security metrics, and markets metrics for the electric power grid. The data for metrics being monitored by the monitor computer are stored in a data base, and a visualization of the metrics is displayed on at least one display computer having a monitor. The at least one display computer in one said control area enables an operator to monitor the grid portion corresponding to a different said control area.

  4. 基于智能手机的智能电网实时监控系统设计%The real-time monitoring system design in the smart-power-grids based on smart-phones

    Institute of Scientific and Technical Information of China (English)

    王佳

    2013-01-01

    互联网和无线通讯技术的不断发展,越来越多的企业都在研发一种比较小巧、便携的监控设备.由于智能手机具有较强的移动性和很大的灵活性,在智能电网系统中结合智能手机的优点,提出了一种基于智能手机在智能电网中的实时监控系统的设计,该系统可以实时的随时随地对智能电网中的电力线路运行状况和用电量进行监控,很好的监控了电网的工作状态.%The continuous development of the Internet and wireless communication technology,more and more enterprises are in the development of a more compact,portable monitoring equipment.Because the smartphone has strong mobility and flexibility,in the smart grid system combined with the advantages of the smartphone,puts forward a real-time monitoring system based on smart phones in the smart grid design,the system can real-time anywhere in smart grid,power line monitor running status,and power consumption,good monitoring the working state of the power grid.

  5. Gas House Autonomous System Monitoring

    Science.gov (United States)

    Miller, Luke; Edsall, Ashley

    2015-01-01

    Gas House Autonomous System Monitoring (GHASM) will employ Integrated System Health Monitoring (ISHM) of cryogenic fluids in the High Pressure Gas Facility at Stennis Space Center. The preliminary focus of development incorporates the passive monitoring and eventual commanding of the Nitrogen System. ISHM offers generic system awareness, adept at using concepts rather than specific error cases. As an enabler for autonomy, ISHM provides capabilities inclusive of anomaly detection, diagnosis, and abnormality prediction. Advancing ISHM and Autonomous Operation functional capabilities enhances quality of data, optimizes safety, improves cost effectiveness, and has direct benefits to a wide spectrum of aerospace applications.

  6. POWER SYSTEMS DEVELOPMENT FACILITY

    Energy Technology Data Exchange (ETDEWEB)

    Unknown

    2002-11-01

    This report discusses test campaign GCT4 of the Kellogg Brown & Root, Inc. (KBR) transport reactor train with a Siemens Westinghouse Power Corporation (Siemens Westinghouse) particle filter system at the Power Systems Development Facility (PSDF) located in Wilsonville, Alabama. The transport reactor is an advanced circulating fluidized-bed reactor designed to operate as either a combustor or a gasifier using one of two possible particulate control devices (PCDs). The transport reactor was operated as a pressurized gasifier during GCT4. GCT4 was planned as a 250-hour test run to continue characterization of the transport reactor using a blend of several Powder River Basin (PRB) coals and Bucyrus limestone from Ohio. The primary test objectives were: Operational Stability--Characterize reactor loop and PCD operations with short-term tests by varying coal-feed rate, air/coal ratio, riser velocity, solids-circulation rate, system pressure, and air distribution. Secondary objectives included the following: Reactor Operations--Study the devolatilization and tar cracking effects from transient conditions during transition from start-up burner to coal. Evaluate the effect of process operations on heat release, heat transfer, and accelerated fuel particle heat-up rates. Study the effect of changes in reactor conditions on transient temperature profiles, pressure balance, and product gas composition. Effects of Reactor Conditions on Synthesis Gas Composition--Evaluate the effect of air distribution, steam/coal ratio, solids-circulation rate, and reactor temperature on CO/CO{sub 2} ratio, synthesis gas Lower Heating Value (LHV), carbon conversion, and cold and hot gas efficiencies. Research Triangle Institute (RTI) Direct Sulfur Recovery Process (DSRP) Testing--Provide syngas in support of the DSRP commissioning. Loop Seal Operations--Optimize loop seal operations and investigate increases to previously achieved maximum solids-circulation rate.

  7. A Solution of Power Quality Monitoring System Based on SOA%一种基于SOA架构的电能质量监测系统解决方案

    Institute of Scientific and Technical Information of China (English)

    丁泽俊; 向阳; 夏锐

    2012-01-01

    A pow e r quality monitoring system based on Service -Oriented Architecture (SOA), featuring a set of principles and methodologies for designing and developing software in the form of interoperable services, is presented in this paper. The method as described, using Java Message Service (JMS), not only can be seamlessly integrated with other systems deployed in the power system, such as EMS and MIS, but also can integrate the power quality systems deployed and to be deployed to achieve advanced power quality monitoring. Rather than the power quality data analysis for the single substation, the SOA -based power quality monitoring system can analyze the power quality data in the range of even a province. The experiments validate the effectiveness of the presented solution.%研究一种基于面向服务架构(Service-Oriented Architecture,SOA)的电能质量监测系统解决方案.该方案采用JMS(Java Message Service)技术,以服务提供方式将各模块解耦,既可无缝集成电力系统的调度自动化系统、生产管理等系统,也可集成已部署与将部署的电能质量监测系统.将各系统无缝集成后,综合各系统的功能和数据,还可完成电能质量分析与评估的高级应用.该方案的现场应用效果表明,基于SOA的电能质量监测系统不仅可以完成单个变电站的电能质量高级分析,还能扩展到片区、供电局甚至省(网)级的高级分析应用.

  8. Thermionic power system power processing and control

    Science.gov (United States)

    Metcalf, Kenneth J.

    1992-01-01

    Thermionic power systems are being considered for space-based miltary applications because of their survivability and high efficiency. Under the direction of the Air Force, conceptual designs were generated for two thermionic power systems to determine preliminary system performance data and direct future component development. This paper discusses the power processing and control (PP&C) subsystem that conditions the thermionic converter power and controls the operation of the reactor and thermionic converter subsystems. The baseline PP&C design and design options are discussed, mass and performance data are provided, and technology needs are identified. The impact on PP&C subsystem mass and efficiency of alternate power levels and boom lengths is also presented. The baseline PP&C subsystem is lightweight and reliable, and it uses proven design concepts to minimize development and testing time. However, the radiation dosages specified in the program research and development announcement (PRDA) are 10 to 100 times the capabilities of present semiconductor devices. While these levels are aggressive, they are considered to be achievable by 1995 if the Air Force and other government agencies continue to actively develop radiation resistant electronics devices for military applications.

  9. Unattended Monitoring System Design Methodology

    Energy Technology Data Exchange (ETDEWEB)

    Drayer, D.D.; DeLand, S.M.; Harmon, C.D.; Matter, J.C.; Martinez, R.L.; Smith, J.D.

    1999-07-08

    A methodology for designing Unattended Monitoring Systems starting at a systems level has been developed at Sandia National Laboratories. This proven methodology provides a template that describes the process for selecting and applying appropriate technologies to meet unattended system requirements, as well as providing a framework for development of both training courses and workshops associated with unattended monitoring. The design and implementation of unattended monitoring systems is generally intended to respond to some form of policy based requirements resulting from international agreements or domestic regulations. Once the monitoring requirements are established, a review of the associated process and its related facilities enables identification of strategic monitoring locations and development of a conceptual system design. The detailed design effort results in the definition of detection components as well as the supporting communications network and data management scheme. The data analyses then enables a coherent display of the knowledge generated during the monitoring effort. The resultant knowledge is then compared to the original system objectives to ensure that the design adequately addresses the fundamental principles stated in the policy agreements. Implementation of this design methodology will ensure that comprehensive unattended monitoring system designs provide appropriate answers to those critical questions imposed by specific agreements or regulations. This paper describes the main features of the methodology and discusses how it can be applied in real world situations.

  10. Engineering monitoring expert system's developer

    Science.gov (United States)

    Lo, Ching F.

    1991-01-01

    This research project is designed to apply artificial intelligence technology including expert systems, dynamic interface of neural networks, and hypertext to construct an expert system developer. The developer environment is specifically suited to building expert systems which monitor the performance of ground support equipment for propulsion systems and testing facilities. The expert system developer, through the use of a graphics interface and a rule network, will be transparent to the user during rule constructing and data scanning of the knowledge base. The project will result in a software system that allows its user to build specific monitoring type expert systems which monitor various equipments used for propulsion systems or ground testing facilities and accrues system performance information in a dynamic knowledge base.

  11. Soldier System Power Sources

    Science.gov (United States)

    2006-12-31

    squad level, with the fundamental goal of reducing the total mass of the electric power sources carried by a Marine in the Expeditionary Forces while...still meeting all of his electric power demands. To achieve that goal, this work investigated the effectiveness of hybrid power sources composed...variously of batteries, fuel cells, and super capacitors, it developed control algorithms for those hybrid power sources , it assessed the value of

  12. Wearable impedance monitoring system for dialysis patients.

    Science.gov (United States)

    Bonnet, S; Bourgerette, A; Gharbi, S; Rubeck, C; Arkouche, W; Massot, B; McAdams, E; Montalibet, A; Jallon, P

    2016-08-01

    This paper describes the development and the validation of a prototype wearable miniaturized impedance monitoring system for remote monitoring in home-based dialysis patients. This device is intended to assess the hydration status of dialysis patients using calf impedance measurements. The system is based on the low-power AD8302 component. The impedance calibration procedure is described together with the Cole parameter estimation and the hydric volume estimation. Results are given on a test cell to validate the design and on preliminary calf measurements showing Cole parameter variations during hemodialysis.

  13. TAS配网运行监控系统在盐池电网的应用%Application of TAS distribution network operation monitoring system in Yanchi power grid

    Institute of Scientific and Technical Information of China (English)

    刘江涛

    2015-01-01

    Aiming at the problems such as long transmission line,more branches,harsh operation condition,frequent power failure,weak monitoring instrumentality and difficult failure search etc., using the TAS distribution network operation monitoring system realizes the functions of failure diagnosis,failure isolation,failure alarm,operation monitoring,abnormal operation state alarm and remote setting protection fixed value. The application result shows that the system can fleetly eliminate failure,shorten the time of failure elimination,reduce the range of power cut,decrease times of power cut and improve reliability of power supply.%针对盐池地区配电网线路长,分支多,运行条件恶劣,故障多发,监控手段薄弱,查找困难等问题,采用TAS配网运行监控系统,实现了配电网故障判断、故障隔离、故障报警、运行监控、异常运行情况告警、远程设定保护定值等功能。应用结果表明:该系统可快速排除故障,缩短故障排查处理时间,缩小停电范围,减少了停电次数,提高供电可靠性。

  14. Balancing modern Power System with large scale of wind power

    DEFF Research Database (Denmark)

    Basit, Abdul; Altin, Müfit; Hansen, Anca Daniela

    2014-01-01

    Power system operators must ensure robust, secure and reliable power system operation even with a large scale integration of wind power. Electricity generated from the intermittent wind in large propor-tion may impact on the control of power system balance and thus deviations in the power system...... to be analysed with improved analytical tools and techniques. This paper proposes techniques for the active power balance control in future power systems with the large scale wind power integration, where power balancing model provides the hour-ahead dispatch plan with reduced planning horizon and the real time...... frequency in small or islanded power systems or tie line power flows in interconnected power systems. Therefore, the large scale integration of wind power into the power system strongly concerns the secure and stable grid operation. To ensure the stable power system operation, the evolving power system has...

  15. NB Power Transmission system

    Energy Technology Data Exchange (ETDEWEB)

    Williamson, J. [NB Power Transmission, Fredericton, NB (Canada)

    2006-07-01

    The NB Power Transmission System operates 6700 km of transmission lines having voltages of 69 kV, 138 kV, 230 kV, and 345 kV. The history of lightning protection on this transmission system was presented. Lightning protection with shield wires has been applied selectively on the 69 kV and 138 kV lines and has been applied to all lines in the 230 kV and 345 kV range. Beginning in 2000, line arresters were installed on selected 69 kV and 138 kV lines. It was noted that although overhead shield wires are commonly installed to capture lightning strikes and shield the conductors, problems can occur if the electrical flashover of insulators result in a line to ground fault. Good grounding is needed to ensure that lightning enters the ground from the tower. The new approach is to install line arresters on structures without overhead shield wires. Line arresters are surge arresters applied in parallel with the insulator string. This new line arrester technology was tested by installing nearly 1200 arresters in the Saint John area. This paper described the reasons for choosing line arresters over shield wires and presented the methods of installation. The problems and failure rates of the installed line arresters were presented along with solutions, including solutions to protect lines against lightning in areas with heavy icing. Recommendations for future research into the use, application and development of line arresters were also presented. tabs., figs.

  16. Heart monitoring systems--a review.

    Science.gov (United States)

    Jain, Puneet Kumar; Tiwari, Anil Kumar

    2014-11-01

    To diagnose health status of the heart, heart monitoring systems use heart signals produced during each cardiac cycle. Many types of signals are acquired to analyze heart functionality and hence several heart monitoring systems such as phonocardiography, electrocardiography, photoplethysmography and seismocardiography are used in practice. Recently, focus on the at-home monitoring of the heart is increasing for long term monitoring, which minimizes risks associated with the patients diagnosed with cardiovascular diseases. It leads to increasing research interest in portable systems having features such as signal transmission capability, unobtrusiveness, and low power consumption. In this paper we intend to provide a detailed review of recent advancements of such heart monitoring systems. We introduce the heart monitoring system in five modules: (1) body sensors, (2) signal conditioning, (3) analog to digital converter (ADC) and compression, (4) wireless transmission, and (5) analysis and classification. In each module, we provide a brief introduction about the function of the module, recent developments, and their limitation and challenges.

  17. Wearable Health Monitoring Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this proposal is to demonstrate the feasibility of producing a wearable health monitoring system for the human body that is functional, comfortable,...

  18. Wearable Health Monitoring Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this proposal is to demonstrate the feasibility of producing a wearable health monitoring system for the human body that is functional, comfortable,...

  19. Low-power hybrid wireless network for monitoring infant incubators.

    Science.gov (United States)

    Shin, D I; Shin, K H; Kim, I K; Park, K S; Lee, T S; Kim, S I; Lim, K S; Huh, S J

    2005-10-01

    We have created a pilot wireless network for the convenient monitoring of temperature and humidity of infant incubators. This system combines infrared and radio frequency (RF) communication in order to minimize the power consumption of slave devices, and we therefore call it a hybrid wireless network. The slave module installed in the infant incubator receives the calling signal from the host with an infrared receiver, and sends temperature and humidity data to the host with an RF transmitter. The power consumption of the host system is not critical, and hence it uses the maximum power of infrared transmission and continuously operating RF receiver. In our test implementation, we included four slave devices. The PC calls each slave device every second and then waits for 6 s, resulting in a total scan period of 10 s. Slave devices receive the calling signals and transmit three data values (temperature, moisture, and skin temperature); their power demand is 1 mW, and can run for about 1000 h on four AA-size nickel-hydride batteries.

  20. Monitoring System for Power Transmission lines Based on 4G Transforming into WIFI Wireless Sensor Network%4G转WIFI无线传感器网络的输电线路监测系统

    Institute of Scientific and Technical Information of China (English)

    邓红雷; 师留阳

    2016-01-01

    提出一种新的解决输电线路监测系统数据发送的通信网络方法———基于4G转WIFI无线传感器网络的输电线路监测系统。该方法通过数据汇集平台和云平台,将数据采集网络、数据通信网和后端数据平台连接,实现输电线路监测数据的采集、处理、发送和显示整个过程。系统具有传输速度快、监测范围广、网络建设方便等优点。%This paper presents a new kind of communication network solution for data sending of monitoring system for pow‐er transmission lines named monitoring system for power transmission lines based on 4G transforming into WIFI wireless sen‐sor network .By data acquisition platform and cloud platform ,it is able to connect data acquisition network ,data communi‐cation network and rear‐end data platform so as to realize the whole process of monitoring data acquisition ,processing , sending and display of power transmission lines .This system has advantages of fast transmission speed ,wide monitoring range ,convenient network construction .

  1. Bewegingsvolgsysteem = Monitor tracking system

    NARCIS (Netherlands)

    Slycke, Per Johan; Veltink, Petrus Hermanus; Roetenberg, Daniel

    2006-01-01

    A motion tracking system for tracking an object composed of object parts in a three-dimensional space. The system comprises a number of magnetic field transmitters; a number of field receivers for receiving the magnetic fields of the field transmitters; a number of inertial measurement units for rec

  2. Bewegingsvolgsysteem = Monitor tracking system

    NARCIS (Netherlands)

    Slycke, Per Johan; Veltink, Petrus Hermanus; Roetenberg, Daniel

    2007-01-01

    A motion tracking system for tracking an object composed of object parts in a three-dimensional space. The system comprises a number of magnetic field transmitters; a number of field receivers for receiving the magnetic fields of the field transmitters; a number of inertial measurement units for rec

  3. Design and Realization of Intelligent Monitoring System for Photovoltaic Grid-connected Power Station%光伏并网电站智能监控系统的设计与实现

    Institute of Scientific and Technical Information of China (English)

    叶琴瑜; 胡天友; 秦文

    2012-01-01

    针对目前光伏并网电站监控系统自动化程度较低、监控技术较落后的状况,提出了一种新型光伏并网电站智能监控系统设计方案.在深入研究DSP技术、现场总线技术及软件编程技术的基础上,详细阐述了系统的软硬件设计.该系统通过DSP控制内部A/D进行采样,并与装载有监控软件和CAN总线的PC机进行通信,实现光伏电站运行参数的采集、控制和显示,从而实时监测电站的运行状况.试验表明,该系统取得了良好的效果.%In accordance with the current situation of the monitoring system for photovoltaic grid-connected power stations, I. e. , low level in automation and backward monitoring techniques, the design scheme for a new type of intelligent monitoring system is proposed. On the basis of in-depth research on technologies of DSP, field buses and software programming, the design of hardware and software of this system are described in detail. In the system, by adopting DSP, the internal A/D sampling is controlled, and communication between system and PC that is loaded with the monitoring software and CAN fieldbus is done, and the acquisition, control and display of the operational parameters of the PV power station are implemented; thus the operational status of the station can be monitored in real time. The experiment verifies that the system offers good effects.

  4. Pluto Express power system architecture

    Energy Technology Data Exchange (ETDEWEB)

    Carr, G.A. [California Inst. of Tech., Pasadena, CA (United States). Jet Propulsion Lab.

    1996-12-31

    The Pluto Express power system must answer the challenge of the next generation spacecraft by reducing its power, mass and volume envelopes. Technology developed by the New Millennium Program will enable the power system to meet the stringent requirements for the Pluto Express mission without exceeding the spacecraft mass and volume budgets. Traditionally, there has been an increasing trend of the percentage of mass of the power system electronics with respect to the total spacecraft mass. With all of the previous technology focus on high density digital packaging, the power system electronics have not been keeping pace forcing the spacecraft to absorb a relative increase in the power system mass. The increasing trend can be reversed by using mixed signal ASICs and high density multi-chip-module (MCM) packaging techniques validated by the New Millennium Program. As the size of the spacecraft shrinks, the power system electronics must become tightly integrated with the spacecraft loads. The power system architecture needs the flexibility to accommodate the specific load requirements without sacrificing the capability for growth or reduction as the spacecraft requirements change throughout the development. Modularity is a key requirement that will reduce the overall power system cost. Although the focus has been on shrinking the power system volume and mass, the efficiency and functionality cannot be ignored. Increased efficiency and functionality will only enhance the power systems capability to reduce spacecraft power requirements. The combination of the New Millennium packaging technologies with the Pluto Express power system architecture will produce a product with the capability to meet a wide range of mission profiles while reducing system development costs.

  5. Modular Biometric Monitoring System

    Science.gov (United States)

    Chmiel, Alan J. (Inventor); Humphreys, Bradley T. (Inventor)

    2017-01-01

    A modular system for acquiring biometric data includes a plurality of data acquisition modules configured to sample biometric data from at least one respective input channel at a data acquisition rate. A representation of the sampled biometric data is stored in memory of each of the plurality of data acquisition modules. A central control system is in communication with each of the plurality of data acquisition modules through a bus. The central control system is configured to control communication of data, via the bus, with each of the plurality of data acquisition modules.

  6. The design, construction, and monitoring of photovoltaic power system and solar thermal system on the Georgia Institute of Technology Aquatic Center. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Long, R.C.

    1996-12-31

    This is a report on the feasibility study, design, and construction of a PV and solar thermal system for the Georgia Tech Aquatic Center. The topics of the report include a discussion of site selection and system selection, funding, design alternatives, PV module selection, final design, and project costs. Included are appendices describing the solar thermal system, the SAC entrance canopy PV mockup, and the PV feasibility study.

  7. Design of network type temperature and humidity monitoring system based on power line communication%基于电力线传输的网络型温湿度监控系统设计

    Institute of Scientific and Technical Information of China (English)

    邵祥兵; 温秀兰; 唐桂富; 金懿铭; 刘海鹏; 朱佳

    2011-01-01

    为提高工作效率,节省成本,设计了一种基于电力线传输的网络型温湿度监控系统.该系统由温湿度监控单元、集成单元和中央控制单元组成;温湿度监控单元通过电力线与集成单元连接,用以采集现场温度和湿度数据并通过电力线通信模块发送至集成单元;集成单元和中央控制单元通过RS232接口连接,监控结果可以图形、报表多种方式显示.实验结果证实了该系统不仪能够有效地实现对多点温湿度的远程采集、监控和历史数据的管理分析,而且大大节省成本.%In order to improve work efficiency and save cost, net work type temperature and humidity monitoring system based on power line carrier communication is designed. The system consists of temperature and humidity monitoring unit, integration unit and comprehensive control unit. The temperature and humidity monitoring unit connects to integration unitby the power line communication and the monitoring unit can send the temperature and humidity data to integration unit by the power line. The integration unit connects to comprehensive control unit by RS232. Monitoring results can be displayed in many ways such as graphic and report form. Experimental results show that the system can not only effectively collect remote multipoint temperature and humidity data,tnonitor and analyze historical data,but also it saves costs greatly.

  8. Research and development of communication power monitoring system based on VPN technology%基于VPN技术的通信电源监控系统的研究与开发

    Institute of Scientific and Technical Information of China (English)

    刘子林; 任卫东

    2013-01-01

    Communication power remote video monitoring technology based on VPN can be achieved through the VPN tunnel operate man-machine interface and timely solutions to the failure of the function of the scene at the corporate headquarters to assist service engineers for real-time video monitoring, on-site communications power site. It can greatly improve the efficiency and reduce the corresponding costs. The actual situation of the communication power monitoring system was analyzed, and a suitable communication power video surveillance program was designed.%基于VPN的远程视频监控技术能够实现在公司总部通过VPN通道对现场通信电源站点进行实时视频监控,协助服务工程师操作人机界面,及时解决现场故障的功能,可以大幅提升工作效率和降低相应的费用.通过分析通信电源监控系统的实际情况,开发了一套适合通信电源实现视频监控的方案.

  9. Low power wireless sensor networks for infrastructure monitoring

    Science.gov (United States)

    Ghaed, Mohammad Hassan; Ghahramani, Mohammad Mahdi; Chen, Gregory; Fojtik, Matthew; Blaauw, David; Flynn, Michael P.; Sylvester, Dennis

    2012-04-01

    Sensors with long lifetimes are ideal for infrastructure monitoring. Miniaturized sensor systems are only capable of storing small amounts of energy. Prior work has increased sensor lifetime through the reduction of supply voltage , necessitating voltage conversion from storage elements such as batteries. Sensor lifetime can be further extended by harvesting from solar, vibrational, or thermal energy. Since harvested energy is sporadic, it must be detected and stored. Harvesting sources do not provide voltage levels suitable for secondary power sources, necessitating DC-DC upconversion. We demonstrate a 8.75mm3 sensor system with a near-threshold ARM microcontroller, custom 3.3fW/bit SRAM, two 1mm2 solar cells, a thin-film Li-ion battery, and integrated power management unit. The 7.7μW system enters a 550pW data-retentive sleep state between measurements and harvests solar energy to enable energy autonomy. Our receiver and transmitter architectures benefit from a design strategy that employs mixed signal and digital circuit schemes that perform well in advanced CMOS integrated circuit technologies. A prototype transmitter implemented in 0.13μm CMOS satisfies the requirements for Zigbee, but consumes far less power consumption than state-of-the-art commercial devices.

  10. Design Scheme of Remote Monitoring System Based on Qt

    Directory of Open Access Journals (Sweden)

    Xu Dawei

    2015-01-01

    Full Text Available This paper introduces a design scheme of remote monitoring system based on Qt, the scheme of remote monitoring system based on S3C2410 and Qt, with the aid of cross platform development tools Qt and powerful ARM platform design and implementation. The development of remote video surveillance system based on embedded terminal has practical significance and value.

  11. POWER SYSTEMS DEVELOPMENT FACILITY

    Energy Technology Data Exchange (ETDEWEB)

    Unknown

    2002-05-01

    This report discusses test campaign GCT3 of the Halliburton KBR transport reactor train with a Siemens Westinghouse Power Corporation (Siemens Westinghouse) particle filter system at the Power Systems Development Facility (PSDF) located in Wilsonville, Alabama. The transport reactor is an advanced circulating fluidized-bed reactor designed to operate as either a combustor or a gasifier using one of two possible particulate control devices (PCDs). The transport reactor was operated as a pressurized gasifier during GCT3. GCT3 was planned as a 250-hour test run to commission the loop seal and continue the characterization of the limits of operational parameter variations using a blend of several Powder River Basin coals and Bucyrus limestone from Ohio. The primary test objectives were: (1) Loop Seal Commissioning--Evaluate the operational stability of the loop seal with sand and limestone as a bed material at different solids circulation rates and establish a maximum solids circulation rate through the loop seal with the inert bed. (2) Loop Seal Operations--Evaluate the loop seal operational stability during coal feed operations and establish maximum solids circulation rate. Secondary objectives included the continuation of reactor characterization, including: (1) Operational Stability--Characterize the reactor loop and PCD operations with short-term tests by varying coal feed, air/coal ratio, riser velocity, solids circulation rate, system pressure, and air distribution. (2) Reactor Operations--Study the devolatilization and tar cracking effects from transient conditions during transition from start-up burner to coal. Evaluate the effect of process operations on heat release, heat transfer, and accelerated fuel particle heat-up rates. Study the effect of changes in reactor conditions on transient temperature profiles, pressure balance, and product gas composition. (3) Effects of Reactor Conditions on Syngas Composition--Evaluate the effect of air distribution, steam

  12. Automatic outdoor monitoring system for photovoltaic panels

    Science.gov (United States)

    Stefancich, Marco; Simpson, Lin; Chiesa, Matteo

    2016-05-01

    Long-term acquisition of solar panel performance parameters, for panels operated at maximum power point in their real environment, is of critical importance in the photovoltaic research sector. However, few options exist for the characterization of non-standard panels such as concentrated photovoltaic systems, heavily soiled or shaded panels or those operating under non-standard spectral illumination; certainly, it is difficult to find such a measurement system that is flexible and affordable enough to be adopted by the smaller research institutes or universities. We present here an instrument aiming to fill this gap, autonomously tracking and maintaining any solar panel at maximum power point while continuously monitoring its operational parameters and dissipating the produced energy without connection to the power grid. The instrument allows periodic acquisition of current-voltage curves to verify the employed maximum power point tracking approach. At the same time, with hardware schematics and software code being provided, it provides a flexible open development environment for the monitoring of non-standard generators like concentrator photovoltaic systems and to test novel power tracking approaches. The key issues, and the corresponding solutions, encountered in the design are analyzed in detail and the relevant schematics presented.

  13. Automatic outdoor monitoring system for photovoltaic panels.

    Science.gov (United States)

    Stefancich, Marco; Simpson, Lin; Chiesa, Matteo

    2016-05-01

    Long-term acquisition of solar panel performance parameters, for panels operated at maximum power point in their real environment, is of critical importance in the photovoltaic research sector. However, few options exist for the characterization of non-standard panels such as concentrated photovoltaic systems, heavily soiled or shaded panels or those operating under non-standard spectral illumination; certainly, it is difficult to find such a measurement system that is flexible and affordable enough to be adopted by the smaller research institutes or universities. We present here an instrument aiming to fill this gap, autonomously tracking and maintaining any solar panel at maximum power point while continuously monitoring its operational parameters and dissipating the produced energy without connection to the power grid. The instrument allows periodic acquisition of current-voltage curves to verify the employed maximum power point tracking approach. At the same time, with hardware schematics and software code being provided, it provides a flexible open development environment for the monitoring of non-standard generators like concentrator photovoltaic systems and to test novel power tracking approaches. The key issues, and the corresponding solutions, encountered in the design are analyzed in detail and the relevant schematics presented.

  14. Automatic outdoor monitoring system for photovoltaic panels

    Energy Technology Data Exchange (ETDEWEB)

    Stefancich, Marco [Consiglio Nazionale delle Ricerce, Istituto dei Materiali per l’Elettronica ed il Magnetismo (CNR-IMEM), Parco Area delle Scienze 37/A, 43124 Parma, Italy; Simpson, Lin [National Renewable Energy Laboratory, 15013 Denver West Parkway, Golden, Colorado 80401, USA; Chiesa, Matteo [Masdar Institute of Science and Technology, P.O. Box 54224, Masdar City, Abu Dhabi, United Arab Emirates

    2016-05-01

    Long-term acquisition of solar panel performance parameters, for panels operated at maximum power point in their real environment, is of critical importance in the photovoltaic research sector. However, few options exist for the characterization of non-standard panels such as concentrated photovoltaic systems, heavily soiled or shaded panels or those operating under non-standard spectral illumination; certainly, it is difficult to find such a measurement system that is flexible and affordable enough to be adopted by the smaller research institutes or universities. We present here an instrument aiming to fill this gap, autonomously tracking and maintaining any solar panel at maximum power point while continuously monitoring its operational parameters and dissipating the produced energy without connection to the power grid. The instrument allows periodic acquisition of current-voltage curves to verify the employed maximum power point tracking approach. At the same time, with hardware schematics and software code being provided, it provides a flexible open development environment for the monitoring of non-standard generators like concentrator photovoltaic systems and to test novel power tracking approaches. The key issues, and the corresponding solutions, encountered in the design are analyzed in detail and the relevant schematics presented.

  15. Remote monitoring of nuclear power plants in Baden-Wuerttemberg.

    Science.gov (United States)

    Neff, U; Müller, U; Mandel, C; Coutinho, P; Aures, R; Grimm, C; Hagmann, M; Wilbois, T; Ren, Y

    2014-08-01

    As part of its responsibilities as nuclear supervisory authority, the Ministry of the Environment, Climate Protection and the Energy Sector Baden-Wuerttemberg (UM) operates a computer-based system for remote monitoring of nuclear power plants (NPPs) (KFUe, Kernreaktor-Fernüberwachung). In addition to the Baden-Wuerttemberg NPPs located at Philippsburg, Neckarwestheim and the disused Obrigheim, those in foreign locations close to the border area, i.e. Fessenheim in France, and Leibstadt and Beznau in Switzerland, are monitored. The KFUe system provides several methods to evaluate and present the measured data as well as to ensure compliance of threshold limits and safety objectives. For the UM, it serves as an instrument of the nuclear supervision. In case of a radioactive release, the authorities responsible for civil protection can use dispersion calculations in order to identify potentially affected areas and to initiate protective measures for the population. Beyond the data collected at the plant sites, various international radiation and meteorological measuring networks are integrated in the KFUe. The State Institute for Environment, Measurements and Nature Protection (LUBW), the technical operator of the KFUe, runs its own special monitoring network for ambient gamma dose rate and nuclide specific activity concentration measurements in the vicinity of each NPP. This article gives an overview of the solution to combine data of different sources on a single screen: dose rate networks, dose rate traces measured by car, airborne gamma spectra of helicopters, mobile dose rate probes, grid data of weather forecasts, dispersion calculations, etc.

  16. Design and Implementation of the Hybrid Wind/PV Power System's Remote Monitoring for Mobile Communication Base Station%移动通信基站风光互补系统远程监控设计与实现

    Institute of Scientific and Technical Information of China (English)

    谢瑛珂; 龚恒翔; 巫江; 朱新才

    2013-01-01

    According to the demand of the hybrid wind/photovoltaic power system for mobile communication site,the study designed a distant monitoring system based on GPRS(General Packet Radio Service) network.The system achieved the hybrid wind/PV power system's real-time data collect and alarm,which include the operation parameters,environmental parameters,storage battery temperature and the video images.The monitoring software and website are designed and developed under the Visual studio.net and SQL Server 2005 environment,and realize the monitoring center and the mobile communication site monitoring terminal wireless communication,hybrid wind/photovoltaic system of remote real-time monitoring,the state analysis,remote controlling and alarming etc.And the real-time data are acquired and processed for display,statistics,analysis and storage,also support for internet access.The monitoring system has been trial running in hybrid wind/PV power system which generate electricity for Yangliu base station that lies in Chongqing Banan district,and meets the requirements of networkization and intelligentialization.It has important guiding significance for application and popularization in Chongqing with geographical meteorological characteristics of hybrid wind/photovoltaic system.%根据移动通信基站风光互补供电系统的需要,设计了基于GPRS网络的远程监控系统,实现了风光互补供电系统现场终端运行状况参数、现场环境参数、蓄电池组温度及现场视频图像的远程实时数据监测与报警.基于Visual.net与SQL Server 2005平台开发了监控软件,实现了监控中心与移动通信基站监控终端的无线通信,风光互补发电系统的远程实时监测、状态分析、远程控制和预警等功能,以及监控数据的实时显示、分析、统计及存储,并支持Internet远程查询和访问.该监控系统目前已在重庆移动公司巴南区杨柳基站风光互补供电系统中试运行,能满足系统

  17. Advanced Risk Management and Monitoring System, ARMMS

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kil Yoo; Han, Sang Hoon; Lim, Ho Gon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2011-10-15

    Many risk informed regulation and applications (RIR and A) are approved and used for the nuclear power plants(NPPs), and more RIR and A will be actively applied in Korea. Also, since Korean NPPs are recently exported to other country such as UAE, RIR and A would be applied to the exported NPPs. Thus, a tool which will help the user apply RIR and A is required. KAERI is being developing a tool, called ARMMS (Advanced Risk Management and Monitoring System), for this purpose. The design plan of ARMMS was introduced in the Ref, and in this paper, the actual implementation of ARMMS is introduced, and the performance monitoring module is introduced

  18. Power system protection 3 application

    CERN Document Server

    1995-01-01

    The worldwide growth in demand for electricity has forced the pace of developments in electrical power system design to meet consumer needs for reliable, secure and cheap supplies. Power system protection, as a technology essential to high quality supply, is widely recognised as a specialism of growing and often critical importance, in which power system needs and technological progress have combined to result in rapid developments in policy and practice in recent years. In the United Kingdom, the need for appropriate training in power system protection was recognised in the early 1960s with t

  19. BES Monitoring & Displaying System

    Institute of Scientific and Technical Information of China (English)

    MengWANG; BingyunZHANG; 等

    2001-01-01

    BES1 Monitoring & Displaying System(BESMDS)is projected to monitor and display the running status of DAQ and Slow Control systems of BES through the Web for worldwide accessing.It provides a real-time remote means of monitoring as well as an approach to study the environmental influence upon physical data taking.The system collects real-time data separately from BES online subsystems by network sockets and stores the data into a database.People can access the system through its web site.which retrieves data on request from the database and can display results in dynamically created images.Its web address in http:// besmds,ihep.ac.cn/

  20. Application Analysis of Power Supply Enterprise Electric Energy Information Collection and Monitoring System%供电企业电能量信息采集与监控系统的应用分析

    Institute of Scientific and Technical Information of China (English)

    温亚东; 郭丽娜

    2016-01-01

    针对供电企业营销工作人员必须到现场核对设备运行情况及抄读数据导致的工作效率低、数据易出错等问题,内蒙古电力(集团)有限责任公司建立了电能量信息采集与监控系统,对用户进行实时监测及管理。该系统可将用户的用电信息上传至后台并生成各类报表,使电力营销工作人员能够准确掌握用户电能使用情况,从而大幅减少由于设备损坏等原因丢失的电量,同时为窃电查处、电量追补等工作提供了有力的依据。%Power supply enterprise marketing staff must go to the site to check the operation of the equipment, which leads to the low efficiency of reading data, data errors and other issues. Inner Mongolia Power (Group) Co.,Ltd. establishes the power information collection and monitoring system, to make real-time monitoring and management of users. The system can be used to upload the users′ information to the background and generate various types of reports, so that the power marketing staff can accurately grasp the situation of the power use, make a significant reduction in power consumption due to equipment damage and other reasons, meanwhile it provides a strong basis for the investigation of stealing and power compensation, etc.

  1. Low-power wireless sensor networks for environmental monitoring

    Science.gov (United States)

    Musaloiu-Elefteri, Razvan

    Significant progress has been made in the field of Wireless Sensor Networks in the decade that passed since its inception. This thesis presents several advances intended to make these networks a suitable instrument for environmental monitoring. The thesis first describes Koala, a low-power data-retrieval system that can achieve duty cycles below 1% by using bulk transfers, and Low Power Probing, a novel mechanism to efficiently wake up a network. The second contribution is Serendipity, another data-retrieval system, which takes advantage of the random rendezvous inherent in the Low Power Probing mechanism to achieve a very low duty cycle for low data rate networks. The third part explores the problem of and presents a solution for the interference between WSNs using IEEE 802.15.4 radios and the ubiquitous WiFi networks in the 2.4 GHz spectrum bandwidth. The last contribution of this thesis is Latte, a restricted version of the JavaScript language, that not only can be compiled to C and dynamically loaded on a sensing node, but can also be simulated and debugged in a JavaScript-enabled browser.

  2. Optical monitoring for power law fluids during spin coating.

    Science.gov (United States)

    Jardim, P L G; Michels, A F; Horowitz, F

    2012-01-30

    Optical monitoring is applied, in situ and in real time, to non-newtonian, power law fluids in the spin coating process. An analytical exact solution is presented for thickness evolution that well fits to most measurement data. As result, typical rheological parameters are obtained for several CMC (carboximetilcelullose) concentrations and rotation speeds. Optical monitoring thus precisely indicates applicability of the model to power law fluids under spin coating.

  3. Power quality load management for large spacecraft electrical power systems

    Science.gov (United States)

    Lollar, Louis F.

    1988-01-01

    In December, 1986, a Center Director's Discretionary Fund (CDDF) proposal was granted to study power system control techniques in large space electrical power systems. Presented are the accomplishments in the area of power system control by power quality load management. In addition, information concerning the distortion problems in a 20 kHz ac power system is presented.

  4. 基于PXI技术的全功率风电变流器监测系统%A Full-Scale Wind Power Converter Monitor System Based on PXI Technology

    Institute of Scientific and Technical Information of China (English)

    陈昭宇; 张建文; 蔡旭

    2012-01-01

    To test the performance of the full—scale wind power converter in its development, a monitoring system is needed not only for the high speed sampling of the numerous channels, but also serves as fault alert, data saving, and data analyzing. In this paper a monitor system for a 3MW full-scale wind power converter based on PXI technology is proposed and realized to meet the above —mentioned requirements. Its realization is described in detail with the solution to the problem of the real time system given. At the end of this paper an application example of the 3WM full —scale wind power converter monitoring system is provided, in which the monitor system has successfully detected and recorded a fault occurred in a converter study test, suggesting that the converter monitor system works well and it is very important to the study of the full-scale wind power converter.%在风力发电并网全功率变流器的研发过程中,为了测试和验证变流器的运行性能,需要一个变流器监测系统,不仅能够满足大量通道的高速数据采集,同时还要具有故障报警、录波、以及数据分析的能力.提出了并实现了一种基于PXI技术的3 MW全功率变流器监测系统以满足上述的要求.详细描述了监测系统软硬件的实现方法,并且给出了大数据量监测系统的实时性问题的软件解决方法.在最后,给出了监测系统在3 MW变流器实际调试过程中捕捉并记录下变流器故障的实例,表明了所提出的变流器监测系统的实效性.

  5. Power supply system design and build for Antarctica telescope

    Science.gov (United States)

    Du, Fujia; Li, Hao; Li, Aiai

    2016-07-01

    Currently, more and more telescopes were built and installed in Dome A of Antarctic. The telescopes are remote controlled, unattended operation due to Dome A's environment. These telescopes must be work successfully at least one year without any failure. According to past experience, the power supply system is the weakest point in whole system. The telescopes have to stop if the power system have a problem, even a minor problem. So the high requirement for power supply system are presented. The requirement include high reliability, the self-diagnosis and perfect monitor system. Furthermore, the optic telescope only can work at night. The power source mainly relay on diesel engine. To protect the Antarctic environment and increase the life of engines. The power capacity is limited during observation. So it need the power supply system must be high power factor, high efficient. To meet these requirement, one power supply system was design and built for Antarctic telescope. The power supply system have the following features. First, we give priority to achieve high reliability. The reliability of power system was calculated and the redundant system is designed to make sure that the spare one can be work immediately when some parts have problems. Second, the perfect monitor system was designed to monitor the voltage, current, power and power factor for each power channel. The status of power supply system can be acquired by internet continuously. All the status will be logged in main computer for future analysis. Third, the PFC (Power Factor Correction) technology was used in power supply system. This technology can dramatically increase the power factor, especially in high power situation. The DC-DC inverter instead of AC-DC inverter was used for different voltage level to increase the efficient of power supply.

  6. Improved Power Quality Monitoring through Phasor Measurement Unit Data Interpretation

    DEFF Research Database (Denmark)

    Pertl, Michael; Marinelli, Mattia; Bindner, Henrik W.

    2015-01-01

    the correct actions for operating the system. In future power systems more measuring sensors including phasor measurement units will be available distributed all over the power system. They can and should be utilized to increase the observability of the power system. In this paper the impact of photovoltaic....... The voltage unbalance factor (VUF) could be a ‘new’ observable for a particular power system condition. Information about the actual injected wind power for a certain grid area could be derived without knowing/measuring the real wind power injection....

  7. Analysis of Trinity Power Metrics for Automated Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Michalenko, Ashley Christine [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-07-28

    This is a presentation from Los Alamos National Laboraotyr (LANL) about the analysis of trinity power metrics for automated monitoring. The following topics are covered: current monitoring efforts, motivation for analysis, tools used, the methodology, work performed during the summer, and future work planned.

  8. Versatile CAMAC power supply controller-monitor with built-in ramping and ripple monitor

    Energy Technology Data Exchange (ETDEWEB)

    Kang, H.; Horelick, D.

    1984-10-01

    An integrated power supply controller-monitor has been designed and is in use to control large power supplies for SLC dc magnets. This single-width CAMAC module contains a 14-bit DAC, a 14-bit ADC, and several channels of optically coupled digital status and control signals. Additional features include built-in selectable ramping rates, self-test capabilities, and a ripple monitor circuit to measure ac ripple in the power supply current.

  9. Review on Environment Monitoring System and Energy Efficiency

    Directory of Open Access Journals (Sweden)

    Nikita Gaikwad

    2015-07-01

    Full Text Available The Environment monitoring is one of the applications of wireless sensor network. The most serious environment pollution is air pollution because different air pollutant causes damage to human health and causes global warming. To avoid such effect on human health and climate change Environment monitoring systems are used. This paper provides the short overview of different environmental air pollution monitoring systems and Energy efficiency in WSN to reduced the power consumption of system.

  10. Models for thermal and mechanical monitoring of power transformers

    Energy Technology Data Exchange (ETDEWEB)

    Vilaithong, Rummiya

    2011-07-01

    At present, for economic reasons, there is an increasing emphasis on keeping transformers in service for longer than in the past. A condition-based maintenance using an online monitoring and diagnostic system is one option to ensure reliability of the transformer operation. The key parameters for effectively monitoring equipment can be selected by failure statistics and estimated failure consequences. In this work, two key aspects of transformer condition monitoring are addressed in depth: thermal behaviour and behaviour of on-load tap changers. In the first part of the work, transformer thermal behaviour is studied, focussing on top-oil temperatures. Through online comparison of a measured value of the top-oil temperature and its calculated value, some rapidly developing failures in power transformers such as malfunction of the cooling unit may be detected. Predictions of top-oil temperature can be obtained by means of a mathematical model. Long-term investigations on some dynamic top-oil temperature models are presented for three different types of transformer units. The last-state top-oil temperature, load current, ambient temperature and the operating state of pumps and fans are applied as inputs of the top-oil temperature models. In the fundamental physical models presented, some constant parameters are required and can be estimated using a least-squares optimization technique. Multilayer Feed-forward and Recurrent neural network models are also proposed and investigated. The neural network models are trained with three different Backpropagation training algorithms: Levenberg-Marquardt, Scaled Conjugate Gradient and Automated Bayesian Regularization. The effect of varying operating conditions of the cooling units and the non-steady-state behaviour of loading conditions, as well as ambient temperature are noted. Results show sophisticated temperature prediction is possible using the neural network models that is generally more accurate than with the physical

  11. Impact of advanced wind power ancillary services on power system

    DEFF Research Database (Denmark)

    Hansen, Anca Daniela; Altin, Müfit

    The objective of this report is to illustrate and analyse, by means of simulation test cases, the impact of wind power advanced ancillary services, like inertial response (IR), power oscillation damping (POD) and synchronising power (SP) on the power system. Generic models for wind turbine, wind...... power plant and power system are used in the investigation....

  12. Optical monitoring of high power direct diode laser cladding

    Science.gov (United States)

    Liu, Shuang; Farahmand, Parisa; Kovacevic, Radovan

    2014-12-01

    Laser cladding is one of the most advanced surface modification techniques which can be used to build and repair high-value components. High power direct diode laser (HPDDL) offers unique quality and cost advantages over other lasers (CO2, Nd:YAG). Especially its rectangular laser beam with top-hat intensity distribution makes HPDDL an ideal tool for large area cladding. In order to utilize this technique successfully, the development of on-line monitoring and process control is necessary. In this study, an optical monitoring system consisting of a high-speed CCD camera, a pyrometer, and an infrared camera was used to analyze the mass- and heat-transfer in the cladding process. The particle transport in flight was viewed by a high-speed CCD camera; the interaction between powder flow and laser beam was observed by an infrared camera; and the thermal behavior of the molten pool was recorded by the pyrometer and the infrared camera. The effects of the processing parameters on the laser attenuation, particle heating and clad properties were investigated based on the obtained signals. The optical monitoring method improved the understanding about mutual interrelated phenomena in the cladding process.

  13. Control system for high power laser drilling workover and completion unit

    Energy Technology Data Exchange (ETDEWEB)

    Zediker, Mark S; Makki, Siamak; Faircloth, Brian O; DeWitt, Ronald A; Allen, Erik C; Underwood, Lance D

    2015-05-12

    A control and monitoring system controls and monitors a high power laser system for performing high power laser operations. The control and monitoring system is configured to perform high power laser operation on, and in, remote and difficult to access locations.

  14. Handbook of power systems I

    CERN Document Server

    Pardalos, P M; Pereira, Mario V; Iliadis, Niko A

    2010-01-01

    Energy is one of the world's most challenging problems, and power systems are an important aspect of energy-related issues. The Handbook of Power Systems contains state-of-the-art contributions on power systems modeling. In particular, it covers topics like operation planning, expansion planning, transmission and distribution modelling, computing technologies in energy systems, energy auctions, risk management, market regulation, stochastic programming in energy, and forecasting in energy. The book is separated into nine sections, which cover the most important areas of energy systems. The con

  15. Power systems engineering and mathematics

    CERN Document Server

    Knight, U G

    1972-01-01

    Power Systems Engineering and Mathematics investigates the application of mathematical aids, particularly the techniques of resource planning, to some of the technical-economic problems of power systems engineering. Topics covered include the process of engineering design and the use of computers in system design and operation; power system planning and operation; time scales and computation in system operation; and load prediction and generation capacity. This volume is comprised of 13 chapters and begins by outlining the stages in the synthesis of designs (or operating states) for engineerin

  16. Robust power system frequency control

    CERN Document Server

    Bevrani, Hassan

    2008-01-01

    Emphasizes the physical and engineering aspects of the power system frequency control design problem while providing a conceptual understanding of frequency regulation and application of robust control techniques. This book summarizes the author's research outcomes, contributions and experiences with power system frequency regulation.

  17. Design of Low-power Intelligent Tire Monitoring System Based on MSP430 MCU%基于MSP430单片机的低功耗智能轮胎监测系统设计

    Institute of Scientific and Technical Information of China (English)

    葛益娴; 杨博; 张加宏; 吴雨生

    2013-01-01

    设计了一种超低功耗的轮胎压力智能监测系统.该系统由轮胎监测模块和中心接收模块两大模块组成,以低功耗MSP430单片机为主控,监测模块利用MPXY8020A传感芯片,进行轮胎温度和压力的检测,并将数据转化后无线发送.中心模块接受数据后进行分析、处理,实现胎压的显示、语音提示、智能管理等功能.该智能轮胎监测系统可以实现对轮胎压力的智能化监测和管理,且功耗特别低,耐用性强,具有较大的实用价值.%A low-power intelligent tire pressure monitor system is designed.This system is composed of two core modules,i.e.,tire monitoring module and central receiver module,which both takes MSP430 MCU as master control.The tire monitoring module utilizes MPXY8020A sensor chip to measure temperature and pressure of tire and send the data by wireless after the measurement data conversion.The central receiver module receives the converted data and analyses them to realize the function of display,voice prompt,intelligent management.The intelligent tire monitoring system with special low-power and strong durability can achieve the intelligent tire pressure monitoring and management,and has great practical value.

  18. 田湾核电站辐射监测系统探讨%The Discussion of Radiation Monitor System about Tianwan Nuclear Power Station

    Institute of Scientific and Technical Information of China (English)

    李伟

    2016-01-01

    Radiation monitoring is an important means to ensure safe and reliable operation of the plant,there are some similarities between each plant,but also has its uniqueness. The advantages and disadvantages of Tianwan’s radiation monitoring systemare introduced in this paper,and put forward some reasonable proposals aboutthe system design and equipment installation based on the results of system operation and maintenance.%辐射监测是确保核电站安全可靠运行的重要手段,各核电站的辐射监测系统既有相同之处,又具有其独特性。本文介绍了田湾核电站辐射监测系统的优点和缺点,并结合系统运行、维修情况,对系统设计、设备安装等提出了合理性建议。

  19. Decision Fusion System for Bolted Joint Monitoring

    Directory of Open Access Journals (Sweden)

    Dong Liang

    2015-01-01

    Full Text Available Bolted joint is widely used in mechanical and architectural structures, such as machine tools, industrial robots, transport machines, power plants, aviation stiffened plate, bridges, and steel towers. The bolt loosening induced by flight load and environment factor can cause joint failure leading to a disastrous accident. Hence, structural health monitoring is critical for the bolted joint detection. In order to realize a real-time and convenient monitoring and satisfy the requirement of advanced maintenance of the structure, this paper proposes an intelligent bolted joint failure monitoring approach using a developed decision fusion system integrated with Lamb wave propagation based actuator-sensor monitoring method. Firstly, the basic knowledge of decision fusion and classifier selection techniques is briefly introduced. Then, a developed decision fusion system is presented. Finally, three fusion algorithms, which consist of majority voting, Bayesian belief, and multiagent method, are adopted for comparison in a real-world monitoring experiment for the large aviation aluminum plate. Based on the results shown in the experiment, a big potential in real-time application is presented that the method can accurately and rapidly identify the bolt loosening by analyzing the acquired strain signal using proposed decision fusion system.

  20. Methodology for the location of PMU for the monitoring of critical oscillations in power systems; Metodologia para la ubicacion de PMU para el monitoreo de oscilaciones criticas en sistemas electricos de potencia

    Energy Technology Data Exchange (ETDEWEB)

    Calderon Guizar, Jorge Guillermo [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2009-07-01

    The deregulation and restructuring undergone by the electrical industry, as well as the tendency at world-wide level of reorganization in generation, transmission and distribution units has brought about, as a consequence, drastic changes in the operation of the electric power systems. The difficulties to construct new transmission power lines and the continuous increase in the electricity consumption are forcing more and more to operate the electric power systems every time nearer their safety limits. Nevertheless, to assure the system reliability without mattering what so plaintiff is the operating condition is a requirement that the electrical companies must satisfy. This panorama has motivated and impelled the use of new technologies for the critical indicators the monitoring that allow the electrical companies to guarantee the system safe operation. In this paper a methodology for the location of Fasorial Measurement Units, better known as FMU for the monitoring of the critical oscillation modes in the electric power systems is presented. [Spanish] La desregulacion y reestructuracion experimentada por la industria electrica, asi como la tendencia a nivel mundial de reorganizacion en unidades de generacion, transmision y distribucion ha traido como consecuencia cambios drasticos en la operacion de los sistemas electricos de potencia. Las dificultades para construir nuevas lineas de transmision y el incremento continuo en el consumo de electricidad estan forzando a operar el sistema electrico de potencia cada vez mas cerca de sus limites de seguridad. Sin embargo, asegurar la confiabilidad del sistema sin importar que tan demandante sea la condicion de operacion es un requisito que las companias electricas deben satisfacer. Este panorama ha motivado e impulsado el uso de nuevas tecnologias para el monitoreo de indicadores criticos que permitan a las companias electricas garantizar una operacion segura del sistema. En este trabajo se presenta una metodologia para

  1. Power system protection 2 systems and methods

    CERN Document Server

    1995-01-01

    The worldwide growth in demand for electricity has forced the pace of developments in electrical power system design to meet consumer needs for reliable, secure and cheap supplies. Power system protection, as a technology essential to high quality supply, is widely recognised as a specialism of growing and often critical importance, in which power system needs and technological progress have combined to result in rapid developments in policy and practice in recent years. In the United Kingdom, the need for appropriate training in power system protection was recognised in the early 1960s with t

  2. Solar Weather Ice Monitoring Station (SWIMS). A low cost, extreme/harsh environment, solar powered, autonomous sensor data gathering and transmission system

    Science.gov (United States)

    Chetty, S.; Field, L. A.

    2013-12-01

    The Arctic ocean's continuing decrease of summer-time ice is related to rapidly diminishing multi-year ice due to the effects of climate change. Ice911 Research aims to develop environmentally respectful materials that when deployed will increase the albedo, enhancing the formation and/preservation of multi-year ice. Small scale deployments using various materials have been done in Canada, California's Sierra Nevada Mountains and a pond in Minnesota to test the albedo performance and environmental characteristics of these materials. SWIMS is a sophisticated autonomous sensor system being developed to measure the albedo, weather, water temperature and other environmental parameters. The system (SWIMS) employs low cost, high accuracy/precision sensors, high resolution cameras, and an extreme environment command and data handling computer system using satellite and terrestrial wireless communication. The entire system is solar powered with redundant battery backup on a floating buoy platform engineered for low temperature (-40C) and high wind conditions. The system also incorporates tilt sensors, sonar based ice thickness sensors and a weather station. To keep the costs low, each SWIMS unit measures incoming and reflected radiation from the four quadrants around the buoy. This allows data from four sets of sensors, cameras, weather station, water temperature probe to be collected and transmitted by a single on-board solar powered computer. This presentation covers the technical, logistical and cost challenges in designing, developing and deploying these stations in remote, extreme environments. Image captured by camera #3 of setting sun on the SWIMS station One of the images captured by SWIMS Camera #4

  3. Space power systems technology

    Science.gov (United States)

    Coulman, George A.

    1994-01-01

    Reported here is a series of studies which examine several potential catalysts and electrodes for some fuel cell systems, some materials for space applications, and mathematical modeling and performance predictions for some solid oxide fuel cells and electrolyzers. The fuel cell systems have a potential for terrestrial applications in addition to solar energy conversion in space applications. Catalysts and electrodes for phosphoric acid fuel cell systems and for polymer electrolyte membrane (PEM) fuel cell and electrolyzer systems were examined.

  4. Phonocardiograph system monitors heart sounds

    Science.gov (United States)

    1966-01-01

    Phonocardiograph system monitors the mechanical activity of the heart in extreme environments. It uses a piezoelectric-crystal microphone with an integral preamplifier, and a signal conditioner having special frequency characteristics. The output signals can be recorded on tape, presented aurally, or transmitted telemetrically to a remote station.

  5. Wireless remote monitoring system for sleep apnea

    Science.gov (United States)

    Oh, Sechang; Kwon, Hyeokjun; Varadan, Vijay K.

    2011-04-01

    Sleep plays the important role of rejuvenating the body, especially the central nervous system. However, more than thirty million people suffer from sleep disorders and sleep deprivation. That can cause serious health consequences by increasing the risk of hypertension, diabetes, heart attack and so on. Apart from the physical health risk, sleep disorders can lead to social problems when sleep disorders are not diagnosed and treated. Currently, sleep disorders are diagnosed through sleep study in a sleep laboratory overnight. This involves large expenses in addition to the inconvenience of overnight hospitalization and disruption of daily life activities. Although some systems provide home based diagnosis, most of systems record the sleep data in a memory card, the patient has to face the inconvenience of sending the memory card to a doctor for diagnosis. To solve the problem, we propose a wireless sensor system for sleep apnea, which enables remote monitoring while the patient is at home. The system has 5 channels to measure ECG, Nasal airflow, body position, abdominal/chest efforts and oxygen saturation. A wireless transmitter unit transmits signals with Zigbee and a receiver unit which has two RF modules, Zigbee and Wi-Fi, receives signals from the transmitter unit and retransmits signals to the remote monitoring system with Zigbee and Wi-Fi, respectively. By using both Zigbee and Wi-Fi, the wireless sensor system can achieve a low power consumption and wide range coverage. The system's features are presented, as well as continuous monitoring results of vital signals.

  6. A Resilient Condition Assessment Monitoring System

    Energy Technology Data Exchange (ETDEWEB)

    Humberto Garcia; Wen-Chiao Lin; Semyon M. Meerkov

    2012-08-01

    An architecture and supporting methods are presented for the implementation of a resilient condition assessment monitoring system that can adaptively accommodate both cyber and physical anomalies to a monitored system under observation. In particular, the architecture includes three layers: information, assessment, and sensor selection. The information layer estimates probability distributions of process variables based on sensor measurements and assessments of the quality of sensor data. Based on these estimates, the assessment layer then employs probabilistic reasoning methods to assess the plant health. The sensor selection layer selects sensors so that assessments of the plant condition can be made within desired time periods. Resilient features of the developed system are then illustrated by simulations of a simplified power plant model, where a large portion of the sensors are under attack.

  7. Power Aware Distributed Systems

    Science.gov (United States)

    2004-01-01

    algorithm from the Army Research Laboratory for power aware analysis. In addition to the algorithm in MATLAB (and ported to C by MIT), the...tool for software energy pro ling”, in Proc. IEEE/ACM DAC, June, 2001. [37] J. L. W. V. Jensen, “Sur les fonctions convexes et les ingalits entre les... fonctions convexes et les ingalits entre les valeurs moyennes”, Acta Math., vol. 30, pp. 175–193, 1906. [37] PARSEC parallel simulation language (http://pcl.cs.ucla.edu/projects/parsec) 19 225

  8. Research on Power Quality Monitoring System and Its Data Storage Format Based on LabVIEW%基于LabVIEW的电能质量监测系统及其数据存储格式的研究*

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

      利用虚拟仪器技术,通过软硬件结合,设计了基于LabVIEW的电能质量监测系统。阐述了硬件设计方案,并重点讨论了电能质量稳态指标的分析方法,系统实现了对电能质量指标实时测量和分析、数据库存储和格式转换等功能。为了克服监测网中多数据源给电能质量数据统一管理分析带来的不便,系统采用IEEE推荐的PQDIF格式存储数据,详细介绍了LabVIEW软件生成PQDIF文件的方法。实验测试表明系统满足电网监测的需求,同时具备电网监测标准化和智能化的特点。%A power quality monitoring system based on LabVIEW is designed by using the technique of virtual instrument through the combination of hardware and software. This paper mainly discusses the hardware designing proposal and the analytical methods of steady index for power quality. It realizes the functions of real-time measurement and analysis, data storage and convertion and waveform saving. In order to overcome multi-data sources, generated by different monitor equipments of power quality monitor network, to cause inconvenience to unified management and analysis of power quality data, the system adopts the storage data in PQDIF recommended by IEEE. A detailed specification of PQDIF file and its implementing method based on LabVIEW are presented. The experiment results show that the system can satisfy the requirement of power monitoring with the characteristic of standardization and intelligent.

  9. Energy Monitoring System Berbasis Web

    Directory of Open Access Journals (Sweden)

    Novan Zulkarnain

    2013-12-01

    Full Text Available Government through the Ministry of Energy and Mineral Resources (ESDM encourages the energy savings at whole buildings in Indonesia. Energy Monitoring System (EMS is a web-based solution to monitor energy usage in a building. The research methods used are the analysis, prototype design and testing. EMSconsists of hardware which consists of electrical sensors, temperature-humidity sensor, and a computer. Data on EMS are designed using Modbus protocol, stored in MySQL database application, and displayed on charts through Dashboard on LED TV using PHP programming.

  10. 基于 ZigBee 的低功耗无线温室环境监测系统设计%Design for Low Power Wireless Greenhouse Environment Monitoring System Based on ZigBee

    Institute of Scientific and Technical Information of China (English)

    任伟; 顾小莉; 王丽华

    2014-01-01

    This paper presents a novel low power wireless greenhouse environmental monitoring system .Based on ZigBee technology ,we construct a wireless sensor network to realize the acquisition of environmental information and single or multi hop transmission , a network node collect all environmental information to be processed by epigenous machine , and the system has scene display and alarm function .We achieve low power design of system in aspects of low power hardware circuit , multi dormancy of node , transfer more quickly .The experimental results show that the system has low power con-sumption , low cost , real-time monitoring and can be used as an important basis for practice and environment control of greenhouse .%提出了一种新型低功耗无线温室环境监测系统,基于 ZigBee 技术构建的无线传感网络实现环境信息采集和单跳或多跳方式的传输,网络中心节点汇集多环境信息由上位机处理,具有现场显示和报警功能。系统从硬件电路低功耗、节点多休眠、传输更迅速3方面实现系统软硬件结合的低功耗设计。结果表明,该系统功耗低、成本低,监测实时稳定,可进一步用作温室作业及其环境控制的重要依据。

  11. Real Time Monitoring and Wear Out of Power Modules

    DEFF Research Database (Denmark)

    Ghimire, Pramod

    the expected lifetime of converters. Real time monitoring of power modules is very important together with a smart control and a driving technique in a converter. This ensures to operate the device within a safe operating area and also to protect from a catastrophic failure. Furthermore, the inherent physical...... parameters that deviate by thermo-mechanical stress need to be identified and also measured during operation. Major stressors for high power multi-chip IGBT modules are identified as maximum junction temperature, temperature cycle, over-voltage, over-current, humidity, vibration etc. In addition, finding...... out is monitored online and also the evolution of degradation in interconnects are studied extensively in order to understand the failure process in high power modules under sinusoidal loading conditions. A number of power modules are tested in active power or thermal cycling for different number...

  12. Protection of industrial power systems

    CERN Document Server

    DAVIES, T

    2006-01-01

    The protection which is installed on an industrial power system is likely to be subjected to more difficult conditions than the protection on any other kind of power system. Starting with the many simple devices which are employed and covering the whole area of industrial power system protection, this book aims to help achieve a thorough understanding of the protection necessary.Vital aspects such as the modern cartridge fuse, types of relays, and the role of the current transformer are covered and the widely used inverse definite-minimum time overcurrent relay, the theory of the M

  13. 77 FR 2521 - Integrated System Power Rates

    Science.gov (United States)

    2012-01-18

    ... Southwestern Power Administration Integrated System Power Rates AGENCY: Southwestern Power Administration, DOE... System pursuant to the Integrated System Rate Schedules which supersede the existing rate schedules... Integrated System pursuant to the following Integrated System Rate Schedules: Rate Schedule P-11,...

  14. Review on Environment Monitoring System and Energy Efficiency

    OpenAIRE

    Nikita Gaikwad; Yogita Mistry

    2015-01-01

    The Environment monitoring is one of the applications of wireless sensor network. The most serious environment pollution is air pollution because different air pollutant causes damage to human health and causes global warming. To avoid such effect on human health and climate change Environment monitoring systems are used. This paper provides the short overview of different environmental air pollution monitoring systems and Energy efficiency in WSN to reduced the power consumption ...

  15. Optimization of power system operation

    CERN Document Server

    Zhu, Jizhong

    2015-01-01

    This book applies the latest applications of new technologies topower system operation and analysis, including new and importantareas that are not covered in the previous edition. Optimization of Power System Operation covers both traditional andmodern technologies, including power flow analysis, steady-statesecurity region analysis, security constrained economic dispatch,multi-area system economic dispatch, unit commitment, optimal powerflow, smart grid operation, optimal load shed, optimalreconfiguration of distribution network, power system uncertaintyanalysis, power system sensitivity analysis, analytic hierarchicalprocess, neural network, fuzzy theory, genetic algorithm,evolutionary programming, and particle swarm optimization, amongothers. New topics such as the wheeling model, multi-areawheeling, the total transfer capability computation in multipleareas, are also addressed. The new edition of this book continues to provide engineers andac demics with a complete picture of the optimization of techn...

  16. 风光互补供电系统在输电线路视频监控中的应用%Application of Wind and Solar Hybrid Power Supply System in Transmission Line Video Monitoring

    Institute of Scientific and Technical Information of China (English)

    曾东; 杜俊杰; 许金明; 张勇

    2012-01-01

    Solar power supply adopted presently cannot content with transmission line video monitoring that worked round-the-clockly and operated-stably in the sequential overcast and rainy weather,consequently formed the blind spot of the transmission line danger location site monitoring,wind and solar hybrid power supply system that uses the complementary between wind And solar resource resolves the question availably.The article introduced the configuration and work elements of wind and solar hybrid power supply system,through analyzing the fact electro-requirement of equipment in transmission line round-the-clock video monitoring system,design the configuration and installation scheme.%目前采用的太阳能供电无法满足输电线路视频监控全天候以及在连续阴雨天持续稳定运行从而形成危险点现场监控盲点,风光互补供电系统利用风能和太阳能资源的互补性实现全天候发电,有效地解决了该问题。本文介绍了风光互补供电系统结构和工作原理,通过分析输电线路全天候视频监控系统各设备的实际用电需求,设计了蓄电池、风力发电机、太阳能光伏电池阵列的配置方案和安装方案。

  17. 主动配电网电能质量实时监测系统设计与实现%Design and Realization of Power Quality Real-time Monitoring System for Active Distribution Networks

    Institute of Scientific and Technical Information of China (English)

    曲广龙; 杨洪耕; 李兰芳

    2015-01-01

    A service-oriented power quality real-time monitoring system for active distribution network (ADN) based on the browser/server(B/S) schema is designed and realized.The system can monitor the power quality of ADN in the process of integrating distributed generators in real time.The influence of power flow direction change on the power quality level is focused on.A power quality information model based on the IEC 61850 standard is developed.By means of the manufacturing message specification (MMS),the power quality real-time monitored data on site are uploaded to the master station for parsing,and then stored in the real-time database.The main wiring diagrams of ADN are modeled and drawn by the Silverlight technology.The client side communicates with the server side through Windows communication foundation(WCF) service for retrieving real-time monitored data.By combining the main wiring diagrams,the power quality real-time monitoring for the whole ADN is realized,while the integrated display of graphics and data is realized.The system has successfully been used in an ADN demonstration project in Guangdong Province,and is able to provide effective data for making control strategies and solving power quality problems in AND,which verifies the reliability and practicability of the system.%设计并实现了一套面向服务的浏览器/服务器(B/S)模式主动配电网电能质量实时监测系统,提供主动配电网逐层消纳分布式电源过程的电能质量实时监测功能,重点观测潮流方向变化对电能质量水平的影响。该系统基于 IEC 61850标准建立电能质量信息模型,通过制造报文规范(MMS)将现场电能质量实时监测数据上传到主站解析并存入实时数据库;采用 Silverlight 技术对主动配电网主接线进行建模和绘制,客户端通过 Windows 通信基础(WCF)服务与服务器端通信,获取实时监测数据,并结合主接线图实现主动配电网电能质量全局实时

  18. 基于CAN总线的码头岸电监控系统实时性分析%Real time analysis of wharf shore power monitoring system based on CAN bus

    Institute of Scientific and Technical Information of China (English)

    季学彬; 窦金生

    2015-01-01

    With the"energy conservation and emission reduction"become imperative, using of wharf power during the ship is in port and intelligent monitoring of wharf shore power supply have becoming a current tendency,further more,it has being vigorously promoted.The CAN bus has the broad application prospect in the field of intelligent monitoring, in big network monitoring system,the real-time of system is very important. This paper analyse the problem of real-time of CAN bus.The CAN protocol simulation model is proposed.Measuring the delay data of CAN message transmission by experiment. Comparison of several optimization problem based on TTCAN algorithm.For the subsequent development of large network monitoring system have some certain reference significance.%随着我国"节能减排"的势在必行,船舶靠港期间使用码头岸电以及岸电供给的智能监控已经成为当前的趋势,并正在大力推广。CAN总线在智能监控领域具有广阔的应用前景,在大型网络监控系统中,监控系统的实时性具有重要的意义。文章分析了CAN总线的实时性问题,针对CAN协议提出了仿真模型,实验测出延时数据,总结比较了当前几种基于TTCAN的算法优化问题。对于开发大型网络监控系统具有一定的现实参考意义。

  19. Wind farm - A power source in future power systems

    DEFF Research Database (Denmark)

    Chen, Zhe; Blaabjerg, Frede

    2009-01-01

    wind turbines and wind farms, and then introduces the wind power development and wind farms. An optimization platform for designing electrical systems of offshore wind farms is briefed. The major issues related to the grid connection requirements and the operation of wind turbines/farms in power......The paper describes modern wind power systems, introduces the issues of large penetration of wind power into power systems, and discusses the possible methods of making wind turbines/farms act as a power source, like conventional power plants in power systems. Firstly, the paper describes modern...... systems are illustrated....

  20. 基于ZigBee技术的电力输电线路监测系统设计%Design of Power Transmission Line Monitoring System Based on ZigBee Technology

    Institute of Scientific and Technical Information of China (English)

    方刚; 张雷

    2013-01-01

    In view of the difficult of real-time monitoring in current power transmission lines,this paper analyzed the applied feasibility of the internet of things in electric power. Because the internet of things has lots of advantages, such as convenient networking , strong scalability, good fault tolerance, low power dissipation and low cost, the power lines monitoring system was designed based on the internet of things, whose core section is the lowest costuming single-chip processor of MSP430 and RF model of CC2430. The system powered by solar energy, and achieved collection, transmission, processing and judgment variety of environmental parameters of lines through ZigBee wireless sensor network technology. And it sent information to the monitoring center by the GPRS when an exception occurred it can send SMS to the person who in charge of in a timely. The system promotes the mutual penetration and technical integration of the smart grid and the Internet of things, to further improve the safety and controllability of the power transmission.%针对当前电力输电线路实时监测困难的问题,分析了物联网技术在电力输电领域应用的可行性,利用物联网的扩展性强、容错性好、功耗小及成本低的特性,以超低功耗MSP430单片机和CC2430射频模块为核心设计出基于物联网的线路监测系统,由太阳能提供电源,通过ZigBee无线传感器网络技术实现对线路多种环境参数的采集、传输、处理和判断,并通过GPRS向上位机监测中心发送数据信息,当出现异常时能够及时向负责人发送手机短信.该系统促进了智能电网与物联网的相互渗透和技术融合,进一步提高了电力传输的安全性和可控性.

  1. TPR system: a powerful technique to monitor carbon nanotube formation during chemical vapour deposition; Sistema RTP: uma tecnica poderosa para o monitoramento da formacao de nanotubos de carbono durante o processo por deposicao de vapor quimico

    Energy Technology Data Exchange (ETDEWEB)

    Tristao, Juliana Cristina; Moura, Flavia Cristina Camilo; Lago, Rochel Montero, E-mail: rochel@ufmg.b [Universidade Federal de Minas Gerais (DQ/UFMG), Belo Horizonte, MG (Brazil). Dept. de Quimica; Sapag, Karim [Universidade Nacional de San Luis (Argentina). Lab. de Ciencias de Superficies y Medios Porosos

    2010-07-01

    In this work, a TPR (Temperature Programmed Reduction) system is used as a powerful tool to monitor carbon nanotubes production during CVD (Chemical Vapour Deposition), The experiments were carried out using catalyst precursors based on Fe-Mo supported on Al{sub 2}O{sub 3} and methane as carbon source. As methane reacts on the Fe metal surface, carbon is deposited and H2 is produced. TPR is very sensitive to the presence of H2 and affords information on the temperature where catalyst is active to form different forms of carbon, the reaction kinetics, the catalyst deactivation and carbon yields. (author)

  2. Triboelectric Nanogenerator Enabled Body Sensor Network for Self-Powered Human Heart-Rate Monitoring.

    Science.gov (United States)

    Lin, Zhiming; Chen, Jun; Li, Xiaoshi; Zhou, Zhihao; Meng, Keyu; Wei, Wei; Yang, Jin; Wang, Zhong Lin

    2017-09-26

    Heart-rate monitoring plays a critical role in personal healthcare management. A low-cost, noninvasive, and user-friendly heart-rate monitoring system is highly desirable. Here, a self-powered wireless body sensor network (BSN) system is developed for heart-rate monitoring via integration of a downy-structure-based triboelectric nanogenerator (D-TENG), a power management circuit, a heart-rate sensor, a signal processing unit, and Bluetooth module for wireless data transmission. By converting the inertia energy of human walking into electric power, a maximum power of 2.28 mW with total conversion efficiency of 57.9% was delivered at low operation frequency, which is capable of immediately and sustainably driving the highly integrated BSN system. The acquired heart-rate signal by the sensor would be processed in the signal process circuit, sent to an external device via the Bluetooth module, and displayed on a personal cell phone in a real-time manner. Moreover, by combining a TENG-based generator and a TENG-based sensor, an all-TENG-based wireless BSN system was developed, realizing continuous and self-powered heart-rate monitoring. This work presents a potential method for personal heart-rate monitoring, featured as being self-powered, cost-effective, noninvasive, and user-friendly.

  3. The NASA Carbon Monitoring System

    Science.gov (United States)

    Hurtt, G. C.

    2015-12-01

    Greenhouse gas emission inventories, forest carbon sequestration programs (e.g., Reducing Emissions from Deforestation and Forest Degradation (REDD and REDD+), cap-and-trade systems, self-reporting programs, and their associated monitoring, reporting and verification (MRV) frameworks depend upon data that are accurate, systematic, practical, and transparent. A sustained, observationally-driven carbon monitoring system using remote sensing data has the potential to significantly improve the relevant carbon cycle information base for the U.S. and world. Initiated in 2010, NASA's Carbon Monitoring System (CMS) project is prototyping and conducting pilot studies to evaluate technological approaches and methodologies to meet carbon monitoring and reporting requirements for multiple users and over multiple scales of interest. NASA's approach emphasizes exploitation of the satellite remote sensing resources, computational capabilities, scientific knowledge, airborne science capabilities, and end-to-end system expertise that are major strengths of the NASA Earth Science program. Through user engagement activities, the NASA CMS project is taking specific actions to be responsive to the needs of stakeholders working to improve carbon MRV frameworks. The first phase of NASA CMS projects focused on developing products for U.S. biomass/carbon stocks and global carbon fluxes, and on scoping studies to identify stakeholders and explore other potential carbon products. The second phase built upon these initial efforts, with a large expansion in prototyping activities across a diversity of systems, scales, and regions, including research focused on prototype MRV systems and utilization of COTS technologies. Priorities for the future include: 1) utilizing future satellite sensors, 2) prototyping with commercial off-the-shelf technology, 3) expanding the range of prototyping activities, 4) rigorous evaluation, uncertainty quantification, and error characterization, 5) stakeholder

  4. Water Powered Bioassay System

    Science.gov (United States)

    2004-06-01

    capillary micropump 27 Figure 30: Slow dripping/separation of a droplet from a capillary 4.1.5 Micro Osmotic Pumping Nano Droplet...stored and delivered fluidic pressure and, with a combination of pumps and valves, formed the basic micro fluidic processing unit. The addition of...System, Microvalve, Micro -Accumulator, Micro Dialysis Needle, Bioassay System, Water Activated, Micro Osmotic Pump 16. PRICE CODE 17. SECURITY

  5. Frequency control in power systems with high wind power penetration

    Energy Technology Data Exchange (ETDEWEB)

    Tarnowski, German Claudio [Technical Univ. of Denmark (Denmark). Centre for Electric Technology; Vestas Wind Systems A/S, Alsve (Denmark); Kjaer, Philip Carne [Vestas Wind Systems A/S, Alsve (Denmark); Oestergaard, Jacob [Technical Univ. of Denmark (Denmark). Centre for Electric Technology; Soerensen, Poul E. [Risoe National Laboratory for Sustainable Energy, Roskilde (Denmark). Wind Energy Dept.

    2010-07-01

    The fluctuating nature of wind power introduces several challenges to reliable operation of power system. With high wind power penetration, conventional power plants are displaced and wind speed fluctuations introduce large power imbalances which lead to power system frequency control and operational problems. This paper analysis the impact of wind power in the frequency control of power systems for different amount of controllable variable speed wind turbines. Real measurements from short term wind power penetration tests in a power system are shown and used to study the amount of total regulating power needed from conventional power plants. Dynamic simulations with validated model of the power system support the studies. The paper also presents control concepts for wind power plants necessary to achieve characteristic of frequency response and active power balancing similarly to conventional power plants, therefore allowing higher wind power penetration. As the power system dependency on wind power increases, wind power generation has to contribute with dynamic response and control actions similarly to conventional power plants. (orig.)

  6. 29 CFR 1954.2 - Monitoring system.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 9 2010-07-01 2010-07-01 false Monitoring system. 1954.2 Section 1954.2 Labor Regulations...) PROCEDURES FOR THE EVALUATION AND MONITORING OF APPROVED STATE PLANS General § 1954.2 Monitoring system. (a... Act, the Assistant Secretary has established a State Program Performance Monitoring System....

  7. Design and characterization of a novel power over fiber system integrating a high power diode laser

    Science.gov (United States)

    Perales, Mico; Yang, Mei-huan; Wu, Cheng-liang; Hsu, Chin-wei; Chao, Wei-sheng; Chen, Kun-hsein; Zahuranec, Terry

    2017-02-01

    High power 9xx nm diode lasers along with MH GoPower's (MHGP's) flexible line of Photovoltaic Power Converters (PPCs) are spurring high power applications for power over fiber (PoF), including applications for powering remote sensors and sensors monitoring high voltage equipment, powering high voltage IGBT gate drivers, converters used in RF over Fiber (RFoF) systems, and system power applications, including powering UAVs. In PoF, laser power is transmitted over fiber, and is converted to electricity by photovoltaic cells (packaged into Photovoltaic Power Converters, or PPCs) which efficiently convert the laser light. In this research, we design a high power multi-channel PoF system, incorporating a high power 976 nm diode laser, a cabling system with fiber break detection, and a multichannel PPC-module. We then characterizes system features such as its response time to system commands, the PPC module's electrical output stability, the PPC-module's thermal response, the fiber break detection system response, and the diode laser optical output stability. The high power PoF system and this research will serve as a scalable model for those interested in researching, developing, or deploying a high power, voltage isolated, and optically driven power source for high reliability utility, communications, defense, and scientific applications.

  8. Power monitoring and control for large scale projects: SKA, a case study

    Science.gov (United States)

    Barbosa, Domingos; Barraca, João. Paulo; Maia, Dalmiro; Carvalho, Bruno; Vieira, Jorge; Swart, Paul; Le Roux, Gerhard; Natarajan, Swaminathan; van Ardenne, Arnold; Seca, Luis

    2016-07-01

    Large sensor-based science infrastructures for radio astronomy like the SKA will be among the most intensive datadriven projects in the world, facing very high demanding computation, storage, management, and above all power demands. The geographically wide distribution of the SKA and its associated processing requirements in the form of tailored High Performance Computing (HPC) facilities, require a Greener approach towards the Information and Communications Technologies (ICT) adopted for the data processing to enable operational compliance to potentially strict power budgets. Addressing the reduction of electricity costs, improve system power monitoring and the generation and management of electricity at system level is paramount to avoid future inefficiencies and higher costs and enable fulfillments of Key Science Cases. Here we outline major characteristics and innovation approaches to address power efficiency and long-term power sustainability for radio astronomy projects, focusing on Green ICT for science and Smart power monitoring and control.

  9. Software Oriented Data Monitoring System

    CERN Document Server

    K, Phani Nandan

    2010-01-01

    This project "Software Oriented Data Monitoring System" deals with real time monitoring of patients' parameters like body temperature, heart rate etc. The parameters are checked at regular intervals and Short Messaging Service (SMS) is sent to concerned doctor regarding the measured values. If the obtained parameters are above or below critical values, an alert SMS is also sent to the concerned doctor. This system is very much useful in hospitals, which saves the valuable time of the doctor who otherwise will have to monitor the patients throughout the day. Here the analog data from the sensors is first converted into digital form and is fed to the parallel port of the computer. This data obtained is converted into useful parameters, which is monitored and checked for safe limits. Appropriate SMS is sent to the doctor depending on whether the request is from an alert or routine signal. This is possible by interfacing a mobile phone (Siemens c35i) to the serial port of the computer. The SMS is sent from the co...

  10. Monitoring of power demand of foundry machinery, using the example of paddle mixers

    Directory of Open Access Journals (Sweden)

    R. Wrona

    2008-04-01

    Full Text Available The study outlines the basic features of a newly-designed computer-supported system for monitoring and recording the instantaneous power consumption, used to control the operating parameters of foundry machinery. Explored are potential applications of the module for fast recording of instantaneous currents and voltages in a triple phase power supply system in a paddle mixer. Further research areas are indicated, to extend the system and the range of its potential applications.

  11. Remote and Centralized Monitoring of PV Power Plants

    DEFF Research Database (Denmark)

    Kopacz, Csaba; Spataru, Sergiu; Sera, Dezso

    2014-01-01

    the inverters within each PV plant. The monitoring software stores the PV measurements in a data warehouse optimized for managing and data mining large amounts of data, from where it can be later visualized, analyzed and exported. By combining PV production measurements data with I-V curve measurements......This paper presents the concept and operating principles of a low-cost and flexible monitoring system for PV plants. Compared to classical solutions which can require dedicated hardware and/or specialized data logging systems, the monitoring system we propose allows parallel monitoring of PV plants...

  12. Corral Monitoring System assessment results

    Energy Technology Data Exchange (ETDEWEB)

    Filby, E.E.; Haskel, K.J.

    1998-03-01

    This report describes the results of a functional and operational assessment of the Corral Monitoring Systems (CMS), which was designed to detect and document accountable items entering or leaving a monitored site. Its development was motivated by the possibility that multiple sites in the nuclear weapons states of the former Soviet Union might be opened to such monitoring under the provisions of the Strategic Arms Reduction Treaty. The assessment was performed at three levels. One level evaluated how well the planned approach addressed the target application, and which involved tracking sensitive items moving into and around a site being monitored as part of an international treaty or other agreement. The second level examined the overall design and development approach, while the third focused on individual subsystems within the total package. Unfortunately, the system was delivered as disassembled parts and pieces, with very poor documentation. Thus, the assessment was based on fragmentary operating data coupled with an analysis of what documents were provided with the system. The system design seemed to be a reasonable match to the requirements of the target application; however, important questions about site manning and top level administrative control were left unanswered. Four weaknesses in the overall design and development approach were detected: (1) poor configuration control and management, (2) inadequate adherence to a well defined architectural standard, (3) no apparent provision for improving top level error tolerance, and (4) weaknesses in the object oriented programming approach. The individual subsystems were found to offer few features or capabilities that were new or unique, even at the conceptual level. The CMS might possibly have offered a unique combination of features, but this level of integration was never realized, and it had no unique capabilities that could be readily extracted for use in another system.

  13. Slow Monitoring Systems for CUORE

    Science.gov (United States)

    Dutta, Suryabrata; Cuore Collaboration

    2016-09-01

    The Cryogenic Underground Observatory for Rare Events (CUORE) is a ton-scale neutrinoless double-beta decay experiment under construction at the Laboratori Nazionali del Gran Sasso (LNGS). The experiment is comprised of 988 TeO2 bolometric crystals arranged into 19 towers and operated at a temperature of 10 mK. We have developed slow monitoring systems to monitor the cryostat during detector installation, commissioning, data taking, and other crucial phases of the experiment. Our systems use responsive LabVIEW virtual instruments and video streams of the cryostat. We built a website using the Angular, Bootstrap, and MongoDB frameworks to display this data in real-time. The website can also display archival data and send alarms. I will present how we constructed these slow monitoring systems to be robust, accurate, and secure, while maintaining reliable access for the entire collaboration from any platform in order to ensure efficient communications and fast diagnoses of all CUORE systems.

  14. Geological hazard monitoring system in Georgia

    Science.gov (United States)

    Gaprindashvili, George

    2017-04-01

    Georgia belongs to one of world's most complex mountainous regions according to the scale and frequency of Geological processes and damage caused to population, farmlands, and Infrastructure facilities. Geological hazards (landslide, debrisflow/mudflow, rockfall, erosion and etc.) are affecting many populated areas, agricultural fields, roads, oil and gas pipes, high-voltage electric power transmission towers, hydraulic structures, and tourist complexes. Landslides occur almost in all geomorphological zones, resulting in wide differentiation in the failure types and mechanisms and in the size-frequency distribution. In Georgia, geological hazards triggered by: 1. Activation of highly intense earthquakes; 2. Meteorological events provoking the disaster processes on the background of global climatic change; 3. Large-scale Human impact on the environment. The prediction and monitoring of Geological Hazards is a very wide theme, which involves different researchers from different spheres. Geological hazard monitoring is essential to prevent and mitigate these hazards. In past years in Georgia several monitoring system, such as Ground-based geodetic techniques, Debrisflow Early Warning System (EWS) were installed on high sensitive landslide and debrisflow areas. This work presents description of Geological hazard monitoring system in Georgia.

  15. High power lasers & systems

    OpenAIRE

    Chatwin, Chris; Young, Rupert; Birch, Philip

    2015-01-01

    Some laser history;\\ud Airborne Laser Testbed & Chemical Oxygen Iodine Laser (COIL);\\ud Laser modes and beam propagation;\\ud Fibre lasers and applications;\\ud US Navy Laser system – NRL 33kW fibre laser;\\ud Lockheed Martin 30kW fibre laser;\\ud Conclusions

  16. Power Systems Advanced Research

    Energy Technology Data Exchange (ETDEWEB)

    California Institute of Technology

    2007-03-31

    In the 17 quarters of the project, we have accomplished the following milestones - first, construction of the three multiwavelength laser scattering machines for different light scattering study purposes; second, build up of simulation software package for simulation of field and laboratory particulates matters data; third, carried out field online test on exhaust from combustion engines with our laser scatter system. This report gives a summary of the results and achievements during the project's 16 quarters period. During the 16 quarters of this project, we constructed three multiwavelength scattering instruments for PM2.5 particulates. We build up a simulation software package that could automate the simulation of light scattering for different combinations of particulate matters. At the field test site with our partner, Alturdyne, Inc., we collected light scattering data for a small gas turbine engine. We also included the experimental data feedback function to the simulation software to match simulation with real field data. The PM scattering instruments developed in this project involve the development of some core hardware technologies, including fast gated CCD system, accurately triggered Passively Q-Switched diode pumped lasers, and multiwavelength beam combination system. To calibrate the scattering results for liquid samples, we also developed the calibration system which includes liquid PM generator and size sorting instrument, i.e. MOUDI. In this report, we give the concise summary report on each of these subsystems development results.

  17. FLAME MONITORING IN POWER STATION BOILERS USING IMAGE PROCESSING

    OpenAIRE

    K Sujatha; VENMATHI, M.; N. Pappa

    2012-01-01

    Combustion quality in power station boilers plays an important role in minimizing the flue gas emissions. In the present work various intelligent schemes to infer the flue gas emissions by monitoring the flame colour at the furnace of the boiler are proposed here. Flame image monitoring involves capturing the flame video over a period of time with the measurement of various parameters like Carbon dioxide (CO2), excess oxygen (O2), Nitrogen dioxide (NOx), Sulphur dioxide (SOx) and Carbon monox...

  18. Environmental intelligent monitoring system for greenhouse based on solar power supply%基于太阳能供电的温室环境智能监控系统

    Institute of Scientific and Technical Information of China (English)

    龙滢; 张立

    2012-01-01

    系统设计包含太阳能供电和环境智能监控两模块,利用太阳能光伏组件阵列进行光电转换为系统提供电能,并且采用了MPPT和自跟踪的方法,实现对太阳能的高效率利用.借助传感器和微处理器实现环境智能监控,所控制的因子有温度、湿度、CO2浓度以及光照,使农作物生长在最为合适的环境中,提高农作物产量与质量.%The design of this system contains two modules: solar power supply module and environmental intelligent monitoring module. The array of solar PV modules is adopted to provide electric energy for the system by its photoelectric conversion. The MPPT and autotracking method are employed. The environmental intelligent monitoring is realized by sensors and microcontroller. The factors which are monitored by the system are temperature, humidity, CO2 density and illumination, which let crops grow in the most appropriate environment and can improve the yield and quanity of crops.

  19. 计算机监控系统改造在观音阁水库电厂的应用%Application of Computer Monitoring System Transformation in Guanyinge Reservoir Power Plant

    Institute of Scientific and Technical Information of China (English)

    王金华

    2014-01-01

    为全面提高观音阁水库电厂设备的安全运行和发电质量,观音阁水库电厂经过10多年的运行管理,与时俱进,不断完善计算机监控系统及其设备更新改造,目前设备运行良好,已显现出了计算机监控系统自动化改造的优越性。本文对计算机监控系统自动化改造在观音阁水库电厂的应用进行论述。%Guanyinge Reservoir Water Plant is operated and managed for more than 10 years,and the computer monitoring system and equipment updating renovation are constantly improved with the times in order to comprehensively improve the safe operation and power generation quality of equipment in Guanyinge Reservoir Water Plant.The equipment is currently operated well,and the superiority of computer monitoring system automation transformation has been shown.In this paper, the application of computer monitoring system automation transformation in Guanyinge Reservoir Water Plant is discussed.

  20. The Monitoring System Based on Cutting Power and Hydraulic Signals in Deep-hole Drilling%基于切削功率与油压信号的深孔钻削监测系统

    Institute of Scientific and Technical Information of China (English)

    王玮

    2011-01-01

    针对深孔加工系统实时监测困难和可靠性较差的特点,本文应用多传感器综合检测技术,分别采集深孔钻削过程中的切削功率与油压信号,并将两路信号融合起来输入系统进行分析,建立多参数融合的监测系统,由对信号的综合分析得出检测结果.%For the difficulties of real-time monitoring and poor reliability of deep-hole machining system, in this paper, an integrated multi-sensor detection technology is used to analyze the cutting power and hydraulic signals in the process of acquisition of deep-hole drilling and the input system with the integration of the two signals, and multi-parameter integration monitoring systems is established, in the end the monitoring results are got from comprehensive analysis of signals.

  1. Hypoxia, Monitoring, and Mitigation System

    Science.gov (United States)

    2015-08-01

    When compared to max VO2 as derived from a person’s two-mile run an indication of personalized capacity state can be generated which can also be...Monitoring, Alert and Mitigation System HR Heart Rate HRC Heart Rate Complexity HW Hardware IDR Initial Design Review K Thousand m Meters max Maximum... reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of

  2. TidGen Power System Commercialization Project

    Energy Technology Data Exchange (ETDEWEB)

    Sauer, Christopher R. [President & CEO; McEntee, Jarlath [VP Engineering & CTO

    2013-12-30

    ORPC Maine, LLC, a wholly-owned subsidiary of Ocean Renewable Power Company, LLC (collectively ORPC), submits this Final Technical Report for the TidGen® Power System Commercialization Project (Project), partially funded by the U.S. Department of Energy (DE-EE0003647). The Project was built and operated in compliance with the Federal Energy Regulatory Commission (FERC) pilot project license (P-12711) and other permits and approvals needed for the Project. This report documents the methodologies, activities and results of the various phases of the Project, including design, engineering, procurement, assembly, installation, operation, licensing, environmental monitoring, retrieval, maintenance and repair. The Project represents a significant achievement for the renewable energy portfolio of the U.S. in general, and for the U.S. marine hydrokinetic (MHK) industry in particular. The stated Project goal was to advance, demonstrate and accelerate deployment and commercialization of ORPC’s tidal-current based hydrokinetic power generation system, including the energy extraction and conversion technology, associated power electronics, and interconnection equipment capable of reliably delivering electricity to the domestic power grid. ORPC achieved this goal by designing, building and operating the TidGen® Power System in 2012 and becoming the first federally licensed hydrokinetic tidal energy project to deliver electricity to a power grid under a power purchase agreement in North America. Located in Cobscook Bay between Eastport and Lubec, Maine, the TidGen® Power System was connected to the Bangor Hydro Electric utility grid at an on-shore station in North Lubec on September 13, 2012. ORPC obtained a FERC pilot project license for the Project on February 12, 2012 and the first Maine Department of Environmental Protection General Permit issued for a tidal energy project on January 31, 2012. In addition, ORPC entered into a 20-year agreement with Bangor Hydro Electric

  3. System for monitoring microclimate conditions in greenhouse

    Directory of Open Access Journals (Sweden)

    Marković Dušan B.

    2014-01-01

    Full Text Available Monitoring microclimate parameters in different kind of environments has significant contribution to many areas of human activity and production processes. One of them is vegetable production in greenhouses where measurement of its microclimate parameters may influence the decision on taking appropriate action and protect crops. It is also important to preserve optimal condition in greenhouses to facilitate the process of transpiration, plant mineral nutrition and prevent of a variety physiological damage caused by a deficit of some specific nutrients. Systems for monitoring have wide application in the last years thanks to development of modern computer technology. In this paper model of the monitoring system based on smart transducer concept was introduced. Within the system components are based on MSP430 ultra low power micro controllers. They are using wireless communication to exchange data within the system that was structured according to smart transducer concept. User applications from the network could access to system interface using HTTP protocol where web server could be running on the computer or it could be an embedded web server running on micro controller based device.

  4. Events as power source: wireless sustainable corrosion monitoring.

    Science.gov (United States)

    Sun, Guodong; Qiao, Guofu; Zhao, Lin; Chen, Zhibo

    2013-12-17

    This study presents and implements a corrosion-monitoring wireless sensor platform, EPS (Events as Power Source), which monitors the corrosion events in reinforced concrete (RC) structures, while being powered by the micro-energy released from the corrosion process. In EPS, the proposed corrosion-sensing device serves both as the signal source for identifying corrosion and as the power source for driving the sensor mote, because the corrosion process (event) releases electric energy; this is a novel idea proposed by this study. For accumulating the micro-corrosion energy, we integrate EPS with a COTS (Commercial Off-The-Shelf) energy-harvesting chip that recharges a supercapacitor. In particular, this study designs automatic energy management and adaptive transmitted power control polices to efficiently use the constrained accumulated energy. Finally, a set of preliminary experiments based on concrete pore solution are conducted to evaluate the feasibility and the efficacy of EPS.

  5. Events as Power Source: Wireless Sustainable Corrosion Monitoring

    Directory of Open Access Journals (Sweden)

    Guodong Sun

    2013-12-01

    Full Text Available This study presents and implements a corrosion-monitoring wireless sensor platform, EPS (Events as Power Source, which monitors the corrosion events in reinforced concrete (RC structures, while being powered by the micro-energy released from the corrosion process. In EPS, the proposed corrosion-sensing device serves both as the signal source for identifying corrosion and as the power source for driving the sensor mote, because the corrosion process (event releases electric energy; this is a novel idea proposed by this study. For accumulating the micro-corrosion energy, we integrate EPS with a COTS (Commercial Off-The-Shelf energy-harvesting chip that recharges a supercapacitor. In particular, this study designs automatic energy management and adaptive transmitted power control polices to efficiently use the constrained accumulated energy. Finally, a set of preliminary experiments based on concrete pore solution are conducted to evaluate the feasibility and the efficacy of EPS.

  6. Power Quality Real-time Grid-connected PV Plant Monitoring System%并网光伏电站电能质量实时监测系统

    Institute of Scientific and Technical Information of China (English)

    杜金其; 周林

    2013-01-01

    并网光伏电站的电能质量问题已经成为制约光伏发电技术发展的关键因素之一,进行实时电能质量监测有助于光伏发电技术的改进和提高,对于保障电网安全稳定运行具有重大意义.文中开发了一种基于虚拟仪器的并网光伏电站电能质量实时监测系统,该系统实现了对并网光伏电站电能质量三项稳态指标的监测,利用LabSQL模块和数据库技术实现数据存储以及基于C/S模式、B/S模式和Remote Panels技术的信息远程发布方案,使监控中心可通过Internet直接查看即时和历史电能质量数据,实现信息共享.同时利用7.68 kWp光伏电站对文中开发的系统进行验证,试验结果表明该系统能满足实时、准确、长期、连续的实际测量需要.%Power quality of grid-connected PV plant has been one of the key factors which restricted the development of photovoltaic technology.So the supervision of the plant is to improve and enhance the photovoltaic technology and ensure grid security and stability.This paper presented a power quality real-time monitoring system based on LabVIEW,the system can satisfy the requirement of monitoring three steady targets for power quality.This paper proposed the mode of the remote data storage based on the LabSQL module and database technology,meanwhile,information transmission scheme based on the C/S mode,the B/S mode and remote panels technology.Monitoring center can inquire the data of power quality through the Internet.This system was verified by 7.68 kW grid-connected PV system,the test results show that the system could meet the need of actual measurement.

  7. Design of the Remote Monitoring and Fault Diagnosis System for Power Electronic Equipment%电力电子设备远程监控与故障诊断系统设计

    Institute of Scientific and Technical Information of China (English)

    马皓; 韩思亮

    2005-01-01

    针对电力电子设备中监控与故障诊断实时性要求高、数据传输量大、诊断原因复杂的特点,提出了一种具有强兼容性的基于工控机(IPC)和PLC现场控制分布式远程监控与故障诊断系统的新思路.结合电力电子技术、故障诊断技术以及网络技术,设计开发了一种三层C/S结构与Internet结合的电力电子设备远程监控与故障诊断网络系统,着重介绍了具有强兼容性的系统结构、现场监控兼容性设计、数据采集子系统和实时监控子系统等各部分子系统的设计和通信协议设计开发.%To meet the requirement of highly real-time, tremendous data transferring and complicated diagnostic causes of remote monitoring and fault diagnosis with power electronic equipment, a novel idea of distributed system with industrial PC (IPC) and PLC controlling field terminal is proposed in this paper. Based on the techniques of power electronics, fault diagnosis and network, a remote monitoring and fault diagnosis system with combination of a three-layer C/S structure and Internet is presented, which achieves with high compatibility between different equipment. Furthermore, the paper focuses on the discussion about the structure of compatible systems, the compatibility design of remote monitoring and the realization of field control equipment, such as the data collection sub-system, the real-time monitoring sub-system, the fault diagnosis sub-system and the data disposal and management sub-system, and the design of the data transferring sub-system and the communication protocol format.This work is supported by National Natural Science Foundation of China (No. 50207008).

  8. Embedded multiparametric system for volcano monitoring

    Science.gov (United States)

    Moure, David; Torres, Pedro A.; Meletlidis, Stavros; Lopez, Carmen; José Blanco, María

    2014-05-01

    A low cost and low power consumption multiparametric system designed for volcano monitoring is presented. Once tested with various sensors, at present it is installed in two locations in Tenerife, Canary Islands, acquiring and transmitting data in real time. The system is based on a commercial board (Raspberry Pi®, RPi®) that uses an embedded ARMTM processor with a Debian (Wheezy-Raspbian) Linux Operating System. This configuration permits different standard communication systems between devices as USB and ETHERNET, and also communication with integrated circuits is possible. The whole system includes this platform and self-developed hardware and software. Analog signals are acquired at an expansion board with an ADC converter with three 16 bits channels. This board, which is powered directly from the RPi®, provides timing to the sampling data using a Real Time Clock (RTC). Two serial protocols (I2C and SPI) are responsible for communications. Due to the influence of atmospheric phenomena on the volcano monitoring data, the system is complemented by a self-developed meteorological station based on ArduinoCC and low cost commercial sensors (atmospheric pressure, humidity and rainfall). It is powered with the RPi® and it uses a serial protocol for communications. Self-developed software run under Linux OS and handles configuration, signal acquisition, data storage (USB storage or SD card) and data transmission (FTP, web server). Remote configuration, data plotting and downloading is available through a web interface tool. Nowadays, the system is used for gravimetric and oceanic tides data acquisition in Tenerife and soon it will be applied for clinometric data.

  9. Power Quality in DC Power Distribution Systems and Microgrids

    Directory of Open Access Journals (Sweden)

    Stephen Whaite

    2015-05-01

    Full Text Available This review paper discusses power quality considerations for direct current (DC electric power distribution systems, particularly DC microgrids. First, four selected sample DC architectures are discussed to provide motivation for the consideration of power quality in DC systems. Second, a brief overview of power quality challenges in conventional alternating current (AC distribution systems is given to establish the field of power quality. Finally, a survey of literature addressing power quality issues in DC systems is presented, and necessary power quality considerations in DC distribution system design and operation are discussed.

  10. Fuel cell power system for utility vehicle

    Energy Technology Data Exchange (ETDEWEB)

    Graham, M.; Barbir, F.; Marken, F.; Nadal, M. [Energy Partners, Inc., West Palm Beach, FL (United States)

    1996-12-31

    Based on the experience of designing and building the Green Car, a fuel cell/battery hybrid vehicle, and Genesis, a hydrogen/oxygen fuel cell powered transporter, Energy Partners has developed a fuel cell power system for propulsion of an off-road utility vehicle. A 10 kW hydrogen/air fuel cell stack has been developed as a prototype for future mass production. The main features of this stack are discussed in this paper. Design considerations and selection criteria for the main components of the vehicular fuel cell system, such as traction motor, air compressor and compressor motor, hydrogen storage and delivery, water and heat management, power conditioning, and control and monitoring subsystem are discussed in detail.

  11. LUCIDPIPE™ POWER SYSTEM

    OpenAIRE

    Team, Purdue ECT

    2016-01-01

    In most gravity fed water transmission pipelines, it is desired to reduce excess pressure head to prevent undue strain on a pipeline and lower the incidence of leaks. Normally this is done with pressure reducing valves that essentially burn off this excess pressure as heat. The LucidPipe™ system converts it to low cost electricity thereby removing unwanted pressure and generating energy at the same time - energy that can be put used behind the grid or put back on the grid. The LucidPipe™ syst...

  12. Remote Monitoring System Used for Power Substation Integrated Automation%遥视系统用于电力变电站综合自动化

    Institute of Scientific and Technical Information of China (English)

    许文杰

    2011-01-01

    变电站是调控原始电能大小的主要场所,利用变电站设备可完成电能从高到低或从低到高的转换。综合自动化是未来变电站运行的新趋势,将遥视系统运用于变电站运行管理可提高其安全性、可靠性,本文重点分析了遥视系统的相关问题。%Substation is the original power control size of the main site,use substation equipment can complete electrical energy from high to low or from low to high conversion.The integrated automation is the new trend of future substation operation,the remote vision system used in substation operation management can improve its safety, reliability, this paper focuses on the analysis of remote viewing system related problems.

  13. Coastwide Reference Monitoring System (CRMS)

    Science.gov (United States)

    2010-01-01

    In 1990, the U.S. Congress enacted the Coastal Wetlands Planning, Protection and Restoration Act (CWPPRA) in response to growing awareness of a land loss crisis in Louisiana. Projects funded by CWPPRA require monitoring and evaluation of project effectiveness, and there is also a need to assess the cumulative effects of all projects to achieve a sustainable coastal environment. In 2003, the Louisiana Office of Coastal Protection and Restoration (OCPR) and the U.S. Geological Survey (USGS) received approval from the CWPPRA Task Force to implement the Coastwide Reference Monitoring System (CRMS) as a mechanism to monitor and evaluate the effectiveness of CWPPRA projects at the project, region, and coastwide levels. The CRMS design implements a multiple reference approach by using aspects of hydrogeomorphic functional assessments and probabilistic sampling. The CRMS program is as dynamic as the coastal habitats it monitors. The program is currently funded through CWPPRA and provides data for a variety of user groups, including resource managers, academics, landowners, and researchers.

  14. Electric power system applications of optimization

    CERN Document Server

    Momoh, James A

    2008-01-01

    Introduction Structure of a Generic Electric Power System  Power System Models  Power System Control Power System Security Assessment  Power System Optimization as a Function of Time  Review of Optimization Techniques Applicable to Power Systems Electric Power System Models  Complex Power Concepts Three-Phase Systems Per Unit Representation  Synchronous Machine Modeling Reactive Capability Limits Prime Movers and Governing Systems  Automatic Gain Control Transmission Subsystems  Y-Bus Incorporating the Transformer Effect  Load Models  Available Transfer Capability  Illustrative Examples  Power

  15. An Electrical Energy Consumption Monitoring and Forecasting System

    OpenAIRE

    Rojas-Renteria, J. L.; T. D. Espinoza-Huerta; F. S. Tovar-Pacheco; Gonzalez-Perez, J. L.; Lozano-Dorantes, R.

    2016-01-01

    Electricity consumption is currently an issue of great interest for power companies that need an as much as accurate profile for controlling the installed systems but also for designing future expansions and alterations. Detailed monitoring has proved to be valuable for both power companies and consumers. Further, as smart grid technology is bound to result to increasingly flexible rates, an accurate forecast is bound to prove valuable in the future. In this paper, a monitoring and forecastin...

  16. Partial Discharge Monitoring in Power Transformers Using Low-Cost Piezoelectric Sensors

    Directory of Open Access Journals (Sweden)

    Bruno Castro

    2016-08-01

    Full Text Available Power transformers are crucial in an electric power system. Failures in transformers can affect the quality and cause interruptions in the power supply. Partial discharges are a phenomenon that can cause failures in the transformers if not properly monitored. Typically, the monitoring requires high-cost corrective maintenance or even interruptions of the power system. Therefore, the development of online non-invasive monitoring systems to detect partial discharges in power transformers has great relevance since it can reduce significant maintenance costs. Although commercial acoustic emission sensors have been used to monitor partial discharges in power transformers, they still represent a significant cost. In order to overcome this drawback, this paper presents a study of the feasibility of low-cost piezoelectric sensors to identify partial discharges in mineral insulating oil of power transformers. The analysis of the feasibility of the proposed low-cost sensor is performed by its comparison with a commercial acoustic emission sensor commonly used to detect partial discharges. The comparison between the responses in the time and frequency domain of both sensors was carried out and the experimental results indicate that the proposed piezoelectric sensors have great potential in the detection of acoustic waves generated by partial discharges in insulation oil, contributing for the popularization of this noninvasive technique.

  17. Partial Discharge Monitoring in Power Transformers Using Low-Cost Piezoelectric Sensors.

    Science.gov (United States)

    Castro, Bruno; Clerice, Guilherme; Ramos, Caio; Andreoli, André; Baptista, Fabricio; Campos, Fernando; Ulson, José

    2016-08-10

    Power transformers are crucial in an electric power system. Failures in transformers can affect the quality and cause interruptions in the power supply. Partial discharges are a phenomenon that can cause failures in the transformers if not properly monitored. Typically, the monitoring requires high-cost corrective maintenance or even interruptions of the power system. Therefore, the development of online non-invasive monitoring systems to detect partial discharges in power transformers has great relevance since it can reduce significant maintenance costs. Although commercial acoustic emission sensors have been used to monitor partial discharges in power transformers, they still represent a significant cost. In order to overcome this drawback, this paper presents a study of the feasibility of low-cost piezoelectric sensors to identify partial discharges in mineral insulating oil of power transformers. The analysis of the feasibility of the proposed low-cost sensor is performed by its comparison with a commercial acoustic emission sensor commonly used to detect partial discharges. The comparison between the responses in the time and frequency domain of both sensors was carried out and the experimental results indicate that the proposed piezoelectric sensors have great potential in the detection of acoustic waves generated by partial discharges in insulation oil, contributing for the popularization of this noninvasive technique.

  18. Partial Discharge Monitoring in Power Transformers Using Low-Cost Piezoelectric Sensors

    Science.gov (United States)

    Castro, Bruno; Clerice, Guilherme; Ramos, Caio; Andreoli, André; Baptista, Fabricio; Campos, Fernando; Ulson, José

    2016-01-01

    Power transformers are crucial in an electric power system. Failures in transformers can affect the quality and cause interruptions in the power supply. Partial discharges are a phenomenon that can cause failures in the transformers if not properly monitored. Typically, the monitoring requires high-cost corrective maintenance or even interruptions of the power system. Therefore, the development of online non-invasive monitoring systems to detect partial discharges in power transformers has great relevance since it can reduce significant maintenance costs. Although commercial acoustic emission sensors have been used to monitor partial discharges in power transformers, they still represent a significant cost. In order to overcome this drawback, this paper presents a study of the feasibility of low-cost piezoelectric sensors to identify partial discharges in mineral insulating oil of power transformers. The analysis of the feasibility of the proposed low-cost sensor is performed by its comparison with a commercial acoustic emission sensor commonly used to detect partial discharges. The comparison between the responses in the time and frequency domain of both sensors was carried out and the experimental results indicate that the proposed piezoelectric sensors have great potential in the detection of acoustic waves generated by partial discharges in insulation oil, contributing for the popularization of this noninvasive technique. PMID:27517931

  19. Automated chemical monitoring in new projects of nuclear power plant units

    Science.gov (United States)

    Lobanok, O. I.; Fedoseev, M. V.

    2013-07-01

    The development of automated chemical monitoring systems in nuclear power plant units for the past 30 years is briefly described. The modern level of facilities used to support the operation of automated chemical monitoring systems in Russia and abroad is shown. Hardware solutions suggested by the All-Russia Institute for Nuclear Power Plant Operation (which is the General Designer of automated process control systems for power units used in the AES-2006 and VVER-TOI Projects) are presented, including the structure of additional equipment for monitoring water chemistry (taking the Novovoronezh 2 nuclear power plant as an example). It is shown that the solutions proposed with respect to receiving and processing of input measurement signals and subsequent construction of standard control loops are unified in nature. Simultaneous receipt of information from different sources for ensuring that water chemistry is monitored in sufficient scope and with required promptness is one of the problems that have been solved successfully. It is pointed out that improved quality of automated chemical monitoring can be supported by organizing full engineering follow-up of the automated chemical monitoring system's equipment throughout its entire service life.

  20. Self-Powered, Wireless, Remote Meteorologic Monitoring Based on Triboelectric Nanogenerator Operated by Scavenging Wind Energy.

    Science.gov (United States)

    Zhang, Hulin; Wang, Jie; Xie, Yuhang; Yao, Guang; Yan, Zhuocheng; Huang, Long; Chen, Sihong; Pan, Taisong; Wang, Liping; Su, Yuanjie; Yang, Weiqing; Lin, Yuan

    2016-12-07

    Meteorologic monitoring plays a key role on weather forecast and disaster warning and deeply relies on various sensor networks. It is an optimal choice that grabbing the environmental energy around sensors for driving sensor network. Here, we demonstrate a self-powered, wireless, remote meteorologic monitoring system based on an innovative TENG. The TENG has been proved capable of scavenging wind energy and can be employed for self-powered, wireless meteorologic sounding. This work not only promotes the development of renewable energy harvesting, but also exploits and enriches promising applications based on TENGs for self-powered, wireless, remote sensing.

  1. 核电厂辐射监测系统特点及发展趋势分析%Analysis of Features and Development Tendency for Nuclear Power Plant’s Radiation Monitoring System

    Institute of Scientific and Technical Information of China (English)

    余少杰; 张静; 郝锐

    2014-01-01

    Radiation Monitoring System (RMS ) is important to protect the safety of Nuclear Power Plant (NPP) workers ,the public ,the environment ,and also the operation of nuclear power system .The paper anal-yses and summarizes the technical features of RMS for 2nd ,2nd-plus ,and 3rd-generation Pressurized Water Reactor (PWR) ,discusses development tendency of its framework ,intelligence auto-alarm technology ,and post-accident monitoring technology .This study will inform RMS’s design ,operation management ,research and development of new equipment ,etc .%辐射监测系统是保障核电厂工作人员、公众和环境辐射安全以及核动力系统安全运行的重要系统。本文介绍了二代、二代加及三代压水堆核电厂辐射监测系统的特点,探讨分析压水堆核电厂辐射监测系统的框架体系、智能化报警技术以及事故后监测技术等方面的发展趋势,为压水堆核电厂辐射监测系统的设计、运行管理以及新型辐射监测设备的研发提供参考。

  2. 模块式电源监控系统双机热备份的设计%Design of Dual Hot Standby with Monitoring System of Power Supply Module

    Institute of Scientific and Technical Information of China (English)

    曾成; 赵艳玲

    2013-01-01

    To satisfy the strict requirement on reliability for module power, dual hot standby mechanism with fault-tolerant control is proposed in this paper. Design requirement of dual hot standby is research and analyzed, then the design of dual hot standby with monitoring system of module power supply is completed based on CAN bus communication. State diagnosis, real time synchronization strategies and switch control in the realization process of the dual hot standby with monitoring system are discussed further based on CAN bus communication protocol design basis, and gives design and implementation specifically.%为了满足模块式电源对可靠性的严格要求,提出了具有容错控制的双机热备份机制。研究分析了双机热备份的设计需求,完成了基于CAN总线通信的模块式电源监控系统双机热备份的设计。本文在CAN总线通信协议设计的基础上,深入讨论了在双机热备份实现过程中监控系统的状态诊断方法、实时数据同步策略以及切换控制,并给出了具体的设计和实现。

  3. Shared performance monitor in a multiprocessor system

    Science.gov (United States)

    Chiu, George; Gara, Alan G; Salapura, Valentina

    2014-12-02

    A performance monitoring unit (PMU) and method for monitoring performance of events occurring in a multiprocessor system. The multiprocessor system comprises a plurality of processor devices units, each processor device for generating signals representing occurrences of events in the processor device, and, a single shared counter resource for performance monitoring. The performance monitor unit is shared by all processor cores in the multiprocessor system. The PMU is further programmed to monitor event signals issued from non-processor devices.

  4. Valve Health Monitoring System Utilizing Smart Instrumentation

    Science.gov (United States)

    Jensen, Scott L.; Drouant, George J.

    2006-01-01

    The valve monitoring system is a stand alone unit with network capabilities for integration into a higher level health management system. The system is designed for aiding in failure predictions of high-geared ball valves and linearly actuated valves. It performs data tracking and archiving for identifying degraded performance. The data collection types are cryogenic cycles, total cycles, inlet temperature, body temperature torsional strain, linear bonnet strain, preload position, total travel and total directional changes. Events are recorded and time stamped in accordance with the IRIG B True Time. The monitoring system is designed for use in a Class 1 Division II explosive environment. The basic configuration consists of several instrumentation sensor units and a base station. The sensor units are self contained microprocessor controlled and remotely mountable in three by three by two inches. Each unit is potted in a fire retardant substance without any cavities and limited to low operating power for maintaining safe operation in a hydrogen environment. The units are temperature monitored to safeguard against operation outside temperature limitations. Each contains 902-928 MHz band digital transmitters which meet Federal Communication Commission's requirements and are limited to a 35 foot transmission radius for preserving data security. The base-station controller correlates data from the sensor units and generates data event logs on a compact flash memory module for database uploading. The entries are also broadcast over an Ethernet network. Nitrogen purged National Electrical Manufactures Association (NEMA) Class 4 enclosures are used to house the base-station

  5. FLAME MONITORING IN POWER STATION BOILERS USING IMAGE PROCESSING

    Directory of Open Access Journals (Sweden)

    K. Sujatha

    2012-05-01

    Full Text Available Combustion quality in power station boilers plays an important role in minimizing the flue gas emissions. In the present work various intelligent schemes to infer the flue gas emissions by monitoring the flame colour at the furnace of the boiler are proposed here. Flame image monitoring involves capturing the flame video over a period of time with the measurement of various parameters like Carbon dioxide (CO2, excess oxygen (O2, Nitrogen dioxide (NOx, Sulphur dioxide (SOx and Carbon monoxide (CO emissions plus the flame temperature at the core of the fire ball, air/fuel ratio and the combustion quality. Higher the quality of combustion less will be the flue gases at the exhaust. The flame video was captured using an infrared camera. The flame video is then split up into the frames for further analysis. The video splitter is used for progressive extraction of the flame images from the video. The images of the flame are then pre-processed to reduce noise. The conventional classification and clustering techniques include the Euclidean distance classifier (L2 norm classifier. The intelligent classifier includes the Radial Basis Function Network (RBF, Back Propagation Algorithm (BPA and parallel architecture with RBF and BPA (PRBFBPA. The results of the validation are supported with the above mentioned performance measures whose values are in the optimal range. The values of the temperatures, combustion quality, SOx, NOx, CO, CO2 concentrations, air and fuel supplied corresponding to the images were obtained thereby indicating the necessary control action taken to increase or decrease the air supply so as to ensure complete combustion. In this work, by continuously monitoring the flame images, combustion quality was inferred (complete/partial/incomplete combustion and the air/fuel ratio can be automatically varied. Moreover in the existing set-up, measurements like NOx, CO and CO2 are inferred from the samples that are collected periodically or by

  6. Handbook of power systems II

    Energy Technology Data Exchange (ETDEWEB)

    Rebennack, Steffen [Colorado School of Mines, Golden, CO (United States). Div. of Economics and Business; Pardalos, Panos M. [Florida Univ., Gainesville, FL (United States). Dept. of Industrial and Systems Engineering; Pereira, Mario V.F. [Centro Empresarial Rio Praia de Botafogo, Rio de Janeiro (Brazil); Iliadis, Niko A. (eds.) [EnerCoRD, Athens (Greece)

    2010-07-01

    Energy is one of the world's most challenging problems, and power systems are an important aspect of energy related issues. This handbook contains state-of-the-art contributions on power systems modeling and optimization. The book is separated into two volumes with six sections, which cover the most important areas of energy systems. The first volume covers the topics operations planning and expansion planning while the second volume focuses on transmission and distribution modeling, forecasting in energy, energy auctions and markets, as well as risk management. The contributions are authored by recognized specialists in their fields and consist in either state-of-the-art reviews or examinations of state-of-the-art developments. The articles are not purely theoretical, but instead also discuss specific applications in power systems. (orig.)

  7. Handbook of power systems I

    Energy Technology Data Exchange (ETDEWEB)

    Rebennack, Steffen [Colorado School of Mines, Golden, CO (United States). Div. of Economics and Business; Pardalos, Panos M. [Florida Univ., Gainesville, FL (United States). Dept. of Industrial and Systems Engineering; Pereira, Mario V.F. [Centro Empresarial Rio Praia de Botafogo, Rio de Janeiro, RJ (Brazil); Iliadis, Niko A. (eds.) [EnerCoRD, Athens (Greece)

    2010-07-01

    Energy is one of the world's most challenging problems, and power systems are an important aspect of energy related issues. This handbook contains state-of-the-art contributions on power systems modeling and optimization. The book is separated into two volumes with six sections, which cover the most important areas of energy systems. The first volume covers the topics operations planning and expansion planning while the second volume focuses on transmission and distribution modeling, forecasting in energy, energy auctions and markets, as well as risk management. The contributions are authored by recognized specialists in their fields and consist in either state-of-the-art reviews or examinations of state-of-the-art developments. The articles are not purely theoretical, but instead also discuss specific applications in power systems. (orig.)

  8. Solar-powered cooling system

    Energy Technology Data Exchange (ETDEWEB)

    Farmer, Joseph C

    2013-12-24

    A solar-powered adsorption-desorption refrigeration and air conditioning system uses nanostructural materials made of high specific surface area adsorption aerogel as the adsorptive media. Refrigerant molecules are adsorbed on the high surface area of the nanostructural material. A circulation system circulates refrigerant from the nanostructural material to a cooling unit.

  9. Monitoring and Warning System with Ultra-Low Power For Watertight Compartment Working Condition%超低功耗的水密舱工况综合监测报警系统

    Institute of Scientific and Technical Information of China (English)

    雷开卓; 吴春东; 黄强; 杨海波; 于春磊

    2012-01-01

    水密舱的渗漏工况是水下装备可靠工作的安全保障.论述了低功耗设计原理,分析了低功耗单片机的性能参数,并以该单片机为核心,利用集成温度传感器监测温度,湿敏电容结合555振荡器监测湿度,电阻分压监测供电电压,凝露传感器监测渗漏,设计并实现了一款超低功耗的水密舱渗漏及工况综合监测报警系统;分析了单片机监控软件流程,给出了系统性能参数及功能测试数据.综合测试结果表明,本监测系统工作可靠、功能齐全、性价比高,而且最大功耗≤17.5 mW.%The leakage and working condition is the most important security for underwater-tools working well. Low power theory and the inter function framework, system resource and performance parameter of single-chip are analyzed. Take this single-chip as center, using integrated temperature sensor detecting temperature, humi-cap with oscillator detecting humidity, resistance partial pressure detecting voltage, condensation sensor detecting water-leakage, has made one kind of working condition monitoring system for watertight compartment with ultra low power consumption. Analyzing the software program flow, given the function and performance testing data, which has shown that the monitoring system not only have a good performance and detection reliability, but also cost less and power consumption less than 17.5 mW.

  10. Energy Use and Power Levels in New Monitors and Personal Computers

    Energy Technology Data Exchange (ETDEWEB)

    Roberson, Judy A.; Homan, Gregory K.; Mahajan, Akshay; Nordman, Bruce; Webber, Carrie A.; Brown, Richard E.; McWhinney, Marla; Koomey, Jonathan G.

    2002-07-23

    Our research was conducted in support of the EPA ENERGY STAR Office Equipment program, whose goal is to reduce the amount of electricity consumed by office equipment in the U.S. The most energy-efficient models in each office equipment category are eligible for the ENERGY STAR label, which consumers can use to identify and select efficient products. As the efficiency of each category improves over time, the ENERGY STAR criteria need to be revised accordingly. The purpose of this study was to provide reliable data on the energy consumption of the newest personal computers and monitors that the EPA can use to evaluate revisions to current ENERGY STAR criteria as well as to improve the accuracy of ENERGY STAR program savings estimates. We report the results of measuring the power consumption and power management capabilities of a sample of new monitors and computers. These results will be used to improve estimates of program energy savings and carbon emission reductions, and to inform rev isions of the ENERGY STAR criteria for these products. Our sample consists of 35 monitors and 26 computers manufactured between July 2000 and October 2001; it includes cathode ray tube (CRT) and liquid crystal display (LCD) monitors, Macintosh and Intel-architecture computers, desktop and laptop computers, and integrated computer systems, in which power consumption of the computer and monitor cannot be measured separately. For each machine we measured power consumption when off, on, and in each low-power level. We identify trends in and opportunities to reduce power consumption in new personal computers and monitors. Our results include a trend among monitor manufacturers to provide a single very low low-power level, well below the current ENERGY STAR criteria for sleep power consumption. These very low sleep power results mean that energy consumed when monitors are off or in active use has become more important in terms of contribution to the overall unit energy consumption (UEC

  11. Optimization of photovoltaic power systems

    CERN Document Server

    Rekioua, Djamila

    2012-01-01

    Photovoltaic generation is one of the cleanest forms of energy conversion available. One of the advantages offered by solar energy is its potential to provide sustainable electricity in areas not served by the conventional power grid. Optimisation of Photovoltaic Power Systems details explicit modelling, control and optimisation of the most popular stand-alone applications such as pumping, power supply, and desalination. Each section is concluded by an example using the MATLAB(R) and Simulink(R) packages to help the reader understand and evaluate the performance of different photovoltaic syste

  12. Power systems for space exploration

    Science.gov (United States)

    Shipbaugh, Calvin; Solomon, Kenneth A.

    The Outreach Program was designed to solicit creative ideas from academia, research institutions, private enterprises, and the general public and is intended to be helpful in defining promising technical areas and program paths for more detailed study. To the Outreach Program, a number of power system concepts were proposed. In conclusion, there are a number of advanced concepts for space power and propulsion sources that deserve study if we want to expand our ability to not only explore space, but to utilize it. Advanced nuclear concepts and power beaming concepts are two areas worthy of detailed assessments.

  13. The CMS Detector Power System

    CERN Document Server

    Lusin, S

    2008-01-01

    The power system for the on-detector electronics of the CMS Experiment comprises approximately 12000 low voltage channels, with a total power requirement of 1.1 MVA. The radiation environment inside the CMS experimental cavern combined with an ambient magnetic field (reaching up to 1.3 kGauss at the detector periphery) severely limit the available choices of low voltage supplies, effectively ruling out the use of commercial off-the-shelf DC power supplies. Typical current requirements at the CMS detector front end range from 1A-30A per channel at voltages ranging between 1.25V and 8V. This requires in turn that the final stage of the low voltage power supply be located on the detector periphery. Power to the CMS front-end electronics is stabilized by a 2 MVA uninterruptible power supply (UPS) located in a CMS surface building. This UPS isolates the CMS detector from disturbances on the local power grid and provides for 2 minutes of autonomy following a power failure, allowing for an orderly shutdown of detect...

  14. Optimal Management of Power Systems

    OpenAIRE

    Andreassi, Luca; Ubertini, Stefano

    2010-01-01

    The present chapter discusses the importance of energy systems proper management to reduce energy costs and environmental impact. A numerical model for the optimal management of a power plant in buildings and industrial plants is presented. The model allows evaluating different operating strategies for the power plant components. The different strategies are defined on the basis of a pure economic optimisation (minimisation of total cost) and/or of an energetic optimisation (minimisation of f...

  15. Development of Solar Powered Irrigation System

    Science.gov (United States)

    Abdelkerim, A. I.; Sami Eusuf, M. M. R.; Salami, M. J. E.; Aibinu, A.; Eusuf, M. A.

    2013-12-01

    Development of a solar powered irrigation system has been discussed in this paper. This system would be SCADA-based and quite useful in areas where there is plenty of sunshine but insufficient water to carry out farming activities, such as rubber plantation, strawberry plantation, or any plantation, that requires frequent watering. The system is powered by solar system as a renewable energy which uses solar panel module to convert Sunlight into electricity. The development and implementation of an automated SCADA controlled system that uses PLC as a controller is significant to agricultural, oil and gas monitoring and control purpose purposes. In addition, the system is powered by an intelligent solar system in which solar panel targets the radiation from the Sun. Other than that, the solar system has reduced energy cost as well as pollution. The system is equipped with four input sensors; two soil moisture sensors, two level detection sensors. Soil moisture sensor measures the humidity of the soil, whereas the level detection sensors detect the level of water in the tank. The output sides consist of two solenoid valves, which are controlled respectively by two moistures sensors.

  16. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2004-08-31

    The deep hard rock drilling environment induces severe vibrations into the drillstring, which can cause reduced rates of penetration (ROP) and premature failure of the equipment. The only current means of controlling vibration under varying conditions is to change either the rotary speed or the weight-on-bit (WOB). These changes often reduce drilling efficiency. Conventional shock subs are useful in some situations, but often exacerbate the problems. The objective of this project is development of a unique system to monitor and control drilling vibrations in a ''smart'' drilling system. This system has two primary elements: (1) The first is an active vibration damper (AVD) to minimize harmful axial, lateral and torsional vibrations. The hardness of this damper will be continuously adjusted using a robust, fast-acting and reliable unique technology. (2) The second is a real-time system to monitor drillstring vibration, and related parameters. This monitor adjusts the damper according to local conditions. In some configurations, it may also send diagnostic information to the surface via real-time telemetry. The AVD is implemented in a configuration using magnetorheological (MR) fluid. By applying a current to the magnetic coils in the damper, the viscosity of the fluid can be changed rapidly, thereby altering the damping coefficient in response to the measured motion of the tool. Phase I of this program entailed modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype. Phase I of the project was completed by the revised end date of May 31, 2004. The objectives of this phase were met, and all prerequisites for Phase II have been completed.

  17. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2004-08-31

    The deep hard rock drilling environment induces severe vibrations into the drillstring, which can cause reduced rates of penetration (ROP) and premature failure of the equipment. The only current means of controlling vibration under varying conditions is to change either the rotary speed or the weight-on-bit (WOB). These changes often reduce drilling efficiency. Conventional shock subs are useful in some situations, but often exacerbate the problems. The objective of this project is development of a unique system to monitor and control drilling vibrations in a ''smart'' drilling system. This system has two primary elements: (1) The first is an active vibration damper (AVD) to minimize harmful axial, lateral and torsional vibrations. The hardness of this damper will be continuously adjusted using a robust, fast-acting and reliable unique technology. (2) The second is a real-time system to monitor drillstring vibration, and related parameters. This monitor adjusts the damper according to local conditions. In some configurations, it may also send diagnostic information to the surface via real-time telemetry. The AVD is implemented in a configuration using magnetorheological (MR) fluid. By applying a current to the magnetic coils in the damper, the viscosity of the fluid can be changed rapidly, thereby altering the damping coefficient in response to the measured motion of the tool. Phase I of this program entailed modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype. Phase I of the project was completed by the revised end date of May 31, 2004. The objectives of this phase were met, and all prerequisites for Phase II have been completed.

  18. Analysis on energy consumption index system of thermal power plant

    Science.gov (United States)

    Qian, J. B.; Zhang, N.; Li, H. F.

    2017-05-01

    Currently, the increasingly tense situation in the context of resources, energy conservation is a realistic choice to ease the energy constraint contradictions, reduce energy consumption thermal power plants has become an inevitable development direction. And combined with computer network technology to build thermal power “small index” to monitor and optimize the management system, the power plant is the application of information technology and to meet the power requirements of the product market competition. This paper, first described the research status of thermal power saving theory, then attempted to establish the small index system and build “small index” monitoring and optimization management system in thermal power plant. Finally elaborated key issues in the field of small thermal power plant technical and economic indicators to be further studied and resolved.

  19. Automatic respiration monitoring system; Shushin jotai no jido monitoring system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This is a system to recognize automatically status of a person in sleep including respiration stop, toss about in bed, and departure from the bed by performing animated image processing on images of the person in sleep as photographed by a camera, and by obtaining respiration waveforms from changes in the images of the breast. The system has been developed jointly by the Medical Department of Ehime University and Toshiba Engineering Company when commissioned from the Silver Service Promotion Association as a two-year project. The system requires no operation by an operator, can monitor the respiration during sleep on a real time basis from a completely non-restraint condition, and can be utilized for early discovery of crib death and/or apneic syndrome of aged persons and infants. Its effectiveness was verified by the field tests at a special facility for physically and mentally handicapped aged persons. The system was awarded with the first grand prize for an image recognition system from the Japan Automatic Recognition System Association. (translated by NEDO)

  20. General digitalized system on nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Akagi, Katsumi; Kadohara, Hozumi; Taniguchi, Manabu [Mitsubishi Electric Corp., Tokyo (Japan)

    2000-08-01

    Hitherto, instrumentation control system in a PWR nuclear power plant has stepwisely adopted digital technology such as application of digital instrumentation control device to ordinary use (primary/secondary system control device, and so on), application of CRT display system to monitoring function, and so forth, to realize load reduction of an operator due to expansion of operation automation range, upgrading of reliability and maintenance due to self-diagnosis function, reduction of mass in cables due to multiple transfer, and upgrading of visual recognition due to information integration. In next term PWR plant instrumentation control system, under consideration of application practice of conventional digital technology, application of general digitalisation system to adopt digitalisation of overall instrumentation control system containing safety protection system, and central instrumentation system (new type of instrumentation system) and to intend to further upgrade economics, maintenance, operability/monitoring under security of reliability/safety is planned. And, together with embodiment of construction program of the next-term plant, verification at the general digitalisation proto-system aiming at establishment of basic technology on the system is carried out. Then, here was described on abstract of the general digitalisation system and characteristics of a digital type safety protection apparatus to be adopted in the next-term plant. (G.K.)

  1. Hybrid Power Management System and Method

    Science.gov (United States)

    Eichenberg, Dennis J. (Inventor)

    2008-01-01

    A system and method for hybrid power management. The system includes photovoltaic cells, ultracapacitors, and pulse generators. In one embodiment, the hybrid power management system is used to provide power for a highway safety flasher.

  2. 光伏发电短期功率预测模型与电站监控系统设计%The Short-term Prediction Model of Photovoltaic Grid Power Generation and the Design for Monitoring System of a Power Station

    Institute of Scientific and Technical Information of China (English)

    林嵩

    2016-01-01

    At present, there is a large fluctuation and randomicity in output power of the large-scale photovoltaic (pv) grid power generation system. To accurately predict the output power in order to solve problems of peak regulation and schedule in photovoltaic grid, this paper set up a low cost small meteorological station real-time monitoring the environment parameters such as radiation intensity, temperature, humidity, wind direction, wind speed etc. and a monitoring system to monitor the operation condition of the photovoltaic power station and gather the data of meteorology to apply to the identification of the meteorological conditions and the prediction model of a short-term power in the photovoltaic power generation system of wavelet neural network so as to realize the accurate prediction for an output power in the large-scale photovoltaic (pv) grid power system and it could have an important significance to generate and apply in a large-scale photovoltaic (pv) grid power generation system.%目前大规模光伏并网发电系统的输出功率波动大、随机性强,为准确预测光伏电站的输出功率以解决大规模光伏并网发电给电网造成的调峰、调度等难题。通过开发能实时监测环境辐照强度、温度、湿度、风向、风速等环境参数的低成本小型气象站和光伏电站监控系统来监测光伏电站的运行状况和采集气象与电站输出功率的数据,并应用于气象条件聚类识别和小波神经网络光伏发电系统短期发电功率预测模型上,以实现大规模光伏并网发电系统输出功率的精确预测,对大规模光伏并网发电系统的推广应用具有重要意义。

  3. An extensible database architecture for nationwide power quality monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Kuecuek, Dilek; Inan, Tolga; Salor, Oezguel; Demirci, Turan; Buhan, Serkan; Boyrazoglu, Burak [TUBITAK Uzay, Power Electronics Group, TR 06531 Ankara (Turkey); Akkaya, Yener; Uensar, Oezguer; Altintas, Erinc; Haliloglu, Burhan [Turkish Electricity Transmission Co. Inc., TR 06490 Ankara (Turkey); Cadirci, Isik [TUBITAK Uzay, Power Electronics Group, TR 06531 Ankara (Turkey); Hacettepe University, Electrical and Electronics Eng. Dept., TR 06532 Ankara (Turkey); Ermis, Muammer [METU, Electrical and Electronics Eng. Dept., TR 06531 Ankara (Turkey)

    2010-07-15

    Electrical power quality (PQ) data is one of the prevalent types of engineering data. Its measurement at relevant sampling rates leads to large volumes of PQ data to be managed and analyzed. In this paper, an extensible database architecture is presented based on a novel generic data model for PQ data. The proposed architecture is operated on the nationwide PQ data of the Turkish Electricity Transmission System measured in the field by mobile PQ monitoring systems. The architecture is extensible in the sense that it can be used to store and manage PQ data collected by any means with little or no customization. The architecture has three modules: a PQ database corresponding to the implementation of the generic data model, a visual user query interface to enable its users to specify queries to the PQ database and a query processor acting as a bridge between the query interface and the database. The operation of the architecture is illustrated on the field PQ data with several query examples through the visual query interface. The execution of the architecture on this data of considerable volume supports its applicability and convenience for PQ data. (author)

  4. PowerFactory applications for power system analysis

    CERN Document Server

    Gonzalez-Longatt, Francisco

    2014-01-01

    This book presents a comprehensive set of guidelines and applications of DIgSILENT PowerFactory, an advanced power system simulation software package, for different types of power systems studies. Written by specialists in the field, it combines expertise and years of experience in the use of DIgSILENT PowerFactory with a deep understanding of power systems analysis. These complementary approaches therefore provide a fresh perspective on how to model, simulate and analyse power systems. It presents methodological approaches for modelling of system components, including both classical and non-

  5. POWER CONSUMING SYSTEM USING WSN IN HEMS

    Directory of Open Access Journals (Sweden)

    S.SAMA RUHIN

    2017-03-01

    Full Text Available Today’s buildings account for a large fraction of our energy consumption. In an effort to economize scarce fossil fuels on earth, sensor networks are a valuable tool to increase the energy efficiency of buildings without severely reducing our quality of life. Within a smart building many sensors and actuators are interconnected to form a control system. Nowadays, the deployment of a building control system is complicated because of different communication standards. Here we present a web services-based approach to integrate resource constrained sensor and actuator nodes into IP-based networks. A key feature of our approach is its capability for automatic service discovery. The design and development of an intelligent monitoring and controlling system for home appliances in a real time system is reported in this paper. This system principally monitors the electrical parameters such as voltage and current and subsequently calculates the power consumption of the home appliances that are need to be monitored. The innovation of this system is controlling mechanism implementation in so many ways. Also the proposed system is an economical and easily operable. Due to these intelligent characteristics it become an electricity expense reducer and people friendly.

  6. 76 FR 55137 - Monitoring the Effectiveness of Maintenance at Nuclear Power Plants

    Science.gov (United States)

    2011-09-06

    ... COMMISSION Monitoring the Effectiveness of Maintenance at Nuclear Power Plants AGENCY: Nuclear Regulatory..., ``Monitoring the Effectiveness of Maintenance at Nuclear Power Plants.'' This guide endorses Revision 4A to... Effectiveness of Maintenance at Nuclear Power Plants,'' which provides methods that......

  7. Honey Bee Colonies Remote Monitoring System

    Science.gov (United States)

    Gil-Lebrero, Sergio; Quiles-Latorre, Francisco Javier; Ortiz-López, Manuel; Sánchez-Ruiz, Víctor; Gámiz-López, Victoria; Luna-Rodríguez, Juan Jesús

    2016-01-01

    Bees are very important for terrestrial ecosystems and, above all, for the subsistence of many crops, due to their ability to pollinate flowers. Currently, the honey bee populations are decreasing due to colony collapse disorder (CCD). The reasons for CCD are not fully known, and as a result, it is essential to obtain all possible information on the environmental conditions surrounding the beehives. On the other hand, it is important to carry out such information gathering as non-intrusively as possible to avoid modifying the bees’ work conditions and to obtain more reliable data. We designed a wireless-sensor networks meet these requirements. We designed a remote monitoring system (called WBee) based on a hierarchical three-level model formed by the wireless node, a local data server, and a cloud data server. WBee is a low-cost, fully scalable, easily deployable system with regard to the number and types of sensors and the number of hives and their geographical distribution. WBee saves the data in each of the levels if there are failures in communication. In addition, the nodes include a backup battery, which allows for further data acquisition and storage in the event of a power outage. Unlike other systems that monitor a single point of a hive, the system we present monitors and stores the temperature and relative humidity of the beehive in three different spots. Additionally, the hive is continuously weighed on a weighing scale. Real-time weight measurement is an innovation in wireless beehive—monitoring systems. We designed an adaptation board to facilitate the connection of the sensors to the node. Through the Internet, researchers and beekeepers can access the cloud data server to find out the condition of their hives in real time. PMID:28036061

  8. Honey Bee Colonies Remote Monitoring System

    Directory of Open Access Journals (Sweden)

    Sergio Gil-Lebrero

    2016-12-01

    Full Text Available Bees are very important for terrestrial ecosystems and, above all, for the subsistence of many crops, due to their ability to pollinate flowers. Currently, the honey bee populations are decreasing due to colony collapse disorder (CCD. The reasons for CCD are not fully known, and as a result, it is essential to obtain all possible information on the environmental conditions surrounding the beehives. On the other hand, it is important to carry out such information gathering as non-intrusively as possible to avoid modifying the bees’ work conditions and to obtain more reliable data. We designed a wireless-sensor networks meet these requirements. We designed a remote monitoring system (called WBee based on a hierarchical three-level model formed by the wireless node, a local data server, and a cloud data server. WBee is a low-cost, fully scalable, easily deployable system with regard to the number and types of sensors and the number of hives and their geographical distribution. WBee saves the data in each of the levels if there are failures in communication. In addition, the nodes include a backup battery, which allows for further data acquisition and storage in the event of a power outage. Unlike other systems that monitor a single point of a hive, the system we present monitors and stores the temperature and relative humidity of the beehive in three different spots. Additionally, the hive is continuously weighed on a weighing scale. Real-time weight measurement is an innovation in wireless beehive—monitoring systems. We designed an adaptation board to facilitate the connection of the sensors to the node. Through the Internet, researchers and beekeepers can access the cloud data server to find out the condition of their hives in real time.

  9. An integrated system for pipeline condition monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Strong, Andrew P.; Lees, Gareth; Hartog, Arthur; Twohig, Richard; Kader, Kamal; Hilton, Graeme; Mullens, Stephen; Khlybov, Artem [Schlumberger, Southampton (United Kingdom); Sanderson, Norman [BP Exploration, Sunbury (United Kingdom)

    2009-07-01

    In this paper we present the unique and innovative 'Integriti' pipeline and flow line integrity monitoring system developed by Schlumberger in collaboration with BP. The system uses optical fiber distributed sensors to provide simultaneous distributed measurements of temperature, strain and vibration for the detection, monitoring, and location of events including: Third Party Interference (TPI), including multiple simultaneous disturbances; geo-hazards and landslides; gas and oil leaks; permafrost protection. The Integriti technology also provides a unique means for tracking the progress of cleaning and instrumented pigs using existing optical telecom and data communications cables buried close to pipelines. The Integriti solution provides a unique and proactive approach to pipeline integrity management. It performs analysis of a combination of measurands to provide the pipeline operator with an event recognition and location capability, in effect providing a hazard warning system, and offering the operator the potential to take early action to prevent loss. Through the use of remote, optically powered amplification, an unprecedented detection range of 100 km is possible without the need for any electronics and therefore remote power in the field. A system can thus monitor 200 km of pipeline when configured to monitor 100 km upstream and downstream from a single location. As well as detecting conditions and events leading to leaks, this fully integrated system provides a means of detecting and locating small leaks in gas pipelines below the threshold of present online leak detection systems based on monitoring flow parameters. Other significant benefits include: potential reductions in construction costs; enhancement of the operator's existing integrity management program; potential reductions in surveillance costs and HSE risks. In addition to onshore pipeline systems this combination of functionality and range is available for practicable

  10. ADVANCED POWER SYSTEMS ASH BEHAVIOR IN POWER SYSTEMS

    Energy Technology Data Exchange (ETDEWEB)

    ZYGARLICKE, CHRISTOPHER J; MCCOLLOR, DONALD P; KAY, JOHN P; SWANSON, MICHAEL L

    1998-09-01

    The overall goal of this initiative is to develop fundamental knowledge of ash behavior in power systems for the purpose of increasing power production efficiency, reducing operation and maintenance costs, and reducing greenhouse gas emissions into the atmosphere. The specific objectives of this initiative focus primarily on ash behavior related to advanced power systems and include the following: Determine the current status of the fundamental ash interactions and deposition formation mechanisms as already reported through previous or ongoing projects at the EERC or in the literature. Determine sintering mechanisms for temperatures and particle compositions that are less well known and remain for the most part undetermined. Identify the relationship between the temperature of critical viscosity (Tcv ) as measured in a viscometer and the crystallization occurring in the melt. Perform a literature search on the use of heated-stage microscopy (HSM) for examining in situ ash-sintering phenomena and then validate the use of HSM in the determination of viscosity in spherical ash particles. Ascertain the formation and stability of specific mineral or amorphous phases in deposits typical of advanced power systems. Evaluate corrosion for alloys being used in supercritical combustion systems.

  11. Power System Stability Enhancement Using Unified Power Flow Controller

    Directory of Open Access Journals (Sweden)

    Prechanon Kumkratug

    2010-01-01

    Full Text Available Problem statement: The enhancement of transient stability of the power system is one of the most challenging research areas in power engineer. Approach: This study presents the method to enhance transient stability of power system by Unified Power Flow Controller (UPFC. The mathematical model of power system equipped with a UPFC is systematically derived. The parameters of UPFC are modeled into power flow equation and thus it is used to determine control strategy. The swing curves of the three phase faulted power system without and with a UPFC are tested and compared in various cases. Results: The swing curve of system without a UPFC gets increases monotonically and thus the system can be considered as unstable whereas the swing curves of system with a UPFC can return to stable equilibrium point. Conclusion: From the simulation results, the UPFC can enhance transient stability of power system.

  12. An Electrical Energy Consumption Monitoring and Forecasting System

    Directory of Open Access Journals (Sweden)

    J. L. Rojas-Renteria

    2016-10-01

    Full Text Available Electricity consumption is currently an issue of great interest for power companies that need an as much as accurate profile for controlling the installed systems but also for designing future expansions and alterations. Detailed monitoring has proved to be valuable for both power companies and consumers. Further, as smart grid technology is bound to result to increasingly flexible rates, an accurate forecast is bound to prove valuable in the future. In this paper, a monitoring and forecasting system is investigated. The monitoring system was installed in an actual building and the recordings were used to design and evaluate the forecasting system, based on an artificial neural network. Results show that the system can provide detailed monitoring and also an accurate forecast for a building’s consumption.

  13. Study on Network Security Architecture for Power Systems

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The wide application of network technology in power systems brings not only convenience and flexibility but also security threats. An architecture of network security for power system was proposed in this study,which protected data and facilities from being attacked by outside users by means of firewall, security monitor and control system. Firewall was basically the first line of defense for the intranet; the security monitoring system was a kind of IDS (Intrusion Detection System), while security control system provided authentication, authorization,data-encrypted transmission and security management. This architecture provides various security services, such as identification, authentication, authorization, data integrity and confidentiality.

  14. Design of computer monitoring and control system for the complex thermal power plants%复杂热动力装置计算机监控系统设计

    Institute of Scientific and Technical Information of China (English)

    刘永葆; 龚建政; 李鹏

    2001-01-01

    给出了一般复杂热动力装置计算机监控系统的结构方案,讨论了系统硬件结构及配置,分析了系统软件结构及特点,阐述了复杂系统状态参数采集处理的方法以及串行数据通信的实现,展望了系统的应用前景和发展趋势.%The general structure scheme of computer monitoring and control system for complex thermal power plants is presented. The structure and its features of the software and the hardware are analyzed. The acquisition and processing method of the parameters in complex system are described. The implementation of the serial communication is discussed. The application and the development trends are prospected.

  15. Knolls Atomic Power Laboratory environmental monitoring report, calendar year 1999

    Energy Technology Data Exchange (ETDEWEB)

    None

    2000-12-01

    The results of the effluent and environmental monitoring programs at the three Knolls Atomic Power Laboratory (KAPL) Sites are summarized and assessed in this report. Operations at the three KAPL Sites [Knolls Site, Niskayuna, New York; Kesselring Site, West Milton, New York; S1C Site, Windsor, Connecticut] during calendar year 1999 resulted in no significant release of hazardous substances or radioactivity to the environment. The effluent and environmental monitoring programs conducted by KAPL are designed to determine the effectiveness of treatment and control methods, to provide measurement of the concentrations in effluents for comparison with applicable standards, and to assess resultant concentrations in the environment. The monitoring programs include analyses of samples of liquid and gaseous effluents for chemical constituents and radioactivity as well as monitoring of environmental air, water, sediment, and fish. Radiation measurements are also made around the perimeter of each Site and at off-site background locations.

  16. Development of Self-Powered Wireless-Ready High Temperature Electrochemical Sensors for In-Situ Corrosion Monitoring for Boiler Tubes in Next Generation Coal-based Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xingbo [West Virginia Univ., Morgantown, WV (United States)

    2015-06-30

    The key innovation of this project is the synergy of the high temperature sensor technology based on the science of electrochemical measurement and state-of-the-art wireless communication technology. A novel self-powered wireless high temperature electrochemical sensor system has been developed for coal-fired boilers used for power generation. An initial prototype of the in-situ sensor demonstrated the capability of the wireless communication system in the laboratory and in a pilot plant (Industrial USC Boiler Setting) environment to acquire electrochemical potential and current signals during the corrosion process. Uniform and localized under-coal ash deposit corrosion behavior of Inconel 740 superalloy has been studied at different simulated coal ash hot corrosion environments using the developed sensor. Two typical potential noise patterns were found to correlate with the oxidation and sulfidation stages in the hot coal ash corrosion process. Two characteristic current noise patterns indicate the extent of the corrosion. There was a good correlation between the responses of electrochemical test data and the results from corroded surface analysis. Wireless electrochemical potential and current noise signals from a simulated coal ash hot corrosion process were concurrently transmitted and recorded. The results from the performance evaluation of the sensor confirm a high accuracy in the thermodynamic and kinetic response represented by the electrochemical noise and impedance test data.

  17. Power system studies of new ancillary services

    DEFF Research Database (Denmark)

    Hansen, Anca Daniela; Altin, Müfit

    The objective of this report is to illustrate and analyse, by means of simulation test cases, the impact of wind power advanced ancillary services, like inertial response (IR), power oscillation damping (POD) and synchronising power (SP) on the power system. Generic models for wind turbine, wind...... power plant and power system are used in the investigation....

  18. Power system distributed oscilation detection based on Synchrophasor data

    Science.gov (United States)

    Ning, Jiawei

    Along with increasing demand for electricity, integration of renewable energy and deregulation of power market, power industry is facing unprecedented challenges nowadays. Within the last couple of decades, several serious blackouts have been taking place in United States. As an effective approach to prevent that, power system small signal stability monitoring has been drawing more interests and attentions from researchers. With wide-spread implementation of Synchrophasors around the world in the last decade, power systems real-time online monitoring becomes much more feasible. Comparing with planning study analysis, real-time online monitoring would benefit control room operators immediately and directly. Among all online monitoring methods, Oscillation Modal Analysis (OMA), a modal identification method based on routine measurement data where the input is unmeasured ambient excitation, is a great tool to evaluate and monitor power system small signal stability. Indeed, high sampling Synchrophasor data around power system is fitted perfectly as inputs to OMA. Existing methods in OMA for power systems are all based on centralized algorithms applying at control centers only; however, with rapid growing number of online Synchrophasors the computation burden at control centers is and will be continually exponentially expanded. The increasing computation time at control center compromises the real-time feature of online monitoring. The communication efforts between substation and control center will also be out of reach. Meanwhile, it is difficult or even impossible for centralized algorithms to detect some poorly damped local modes. In order to avert previous shortcomings of centralized OMA methods and embrace the new changes in the power systems, two new distributed oscillation detection methods with two new decentralized structures are presented in this dissertation. Since the new schemes brought substations into the big oscillation detection picture, the proposed

  19. The electric power engineering handbook power system stability and control

    CERN Document Server

    Grisby, Leonard L

    2012-01-01

    With contributions from worldwide leaders in the field, Power System Stability and Control, Third Edition (part of the five-volume set, The Electric Power Engineering Handbook) updates coverage of recent developments and rapid technological growth in essential aspects of power systems. Edited by L.L. Grigsby, a respected and accomplished authority in power engineering, and section editors Miroslav Begovic, Prabha Kundur, and Bruce Wollenberg, this reference presents substantially new and revised content. Topics covered include: * Power System Protection * Power System Dynamics and Stability *

  20. Monitoring and Automatic Control for Ship Power Plants Based Logical Algorithms

    Directory of Open Access Journals (Sweden)

    Mahmoud Mohammad Salem Al-suod

    2014-12-01

    Full Text Available Controlling power station systems with diesel engines is vital issue. Algorithms of microprocessors are developed to be used in the control unit of this type of power station systems. Such Algorithms are built in a logic form, and then the control functions are derived using logic functions. Analyzing the contents of the received logic signals allows us to overcome structural redundancy of the systems. Monitor the network parameter is very important to protect the devices used in the power station systems. In this paper automated controller is developed using microprocessor algorithms to view and control the parameters of the system devices such as generator, synchronizers, and load sharers on-line, this will help in improving the system to be fast, reliable and more accurate. This paper proposes an implementation of a subsequent optimization for structural and algorithmic blocks of microprocessor systems automation of ship power plants.

  1. Design of Low Energy Wireless Monitoring Network in Ultrafiltration System of Power Plant%电厂超滤系统低功耗无线监测网络的设计

    Institute of Scientific and Technical Information of China (English)

    汪凤珠; 白焰; 王仁书

    2012-01-01

    为克服现有化学水处理系统所存在的成本高、布线复杂、扩展性差等缺陷,提出了一种基于ZigBee的电厂锅炉补给水超滤系统监测网络的设计方案,并给出了详细的硬件电路和软件设计流程.对状态检测的能耗进行了理论分析和计算,利用PLC实现了整个无线监测系统.测试表明,该设计符合实际需求并且具有较低的功耗.%In order to overcome the defects in the existing chemical water treatment system, such as high cost, complex wiring, poor expansibility, etc, on the basis of ZigBee, a design scheme of monitoring network of boiler water supply ultrafiltration system in power plant is proposed. Detailed hardware circuits and software design flow are given. The energy consumption in state detection is analyzed theoretically and calculated, and the whole wireless monitoring system is implemented with PLC. Tests show that the design features low energy consumption and meets the actual demands.

  2. Anti Interference Measures of Computer Monitoring System in Thermal Power Plant%火力发电厂计算机监控系统的抗干扰措施

    Institute of Scientific and Technical Information of China (English)

    宋延成

    2014-01-01

    The process of thermal power plant operation, the computermonitoring system for its normal operation has a very important role, but in actual work process, due to the interference sources are numerous, would produce a certain interference to the normal work of the computer monitoring and control system, anti interference measures, ensure the normal work of the computer monitoring system is very necessary.%火力发电厂运行的过程中,计算机监控系统对于其正常运行具有非常重要的作用,但是在实际的工作过程中,由于干扰源众多,会对计算机监控系统的正常工作产生一定的干扰,采取有效的抗干扰措施,保证计算机监控系统的正常工作是非常必要的。

  3. Dynamic influences of wind power on the power system

    Energy Technology Data Exchange (ETDEWEB)

    Rosas, Pedro

    2003-03-01

    The thesis first presents the basics influences of wind power on the power system stability and quality by pointing out the main power quality issues of wind power in a small-scale case and following, the expected large-scale problems are introduced. Secondly, a dynamic wind turbine model that supports power quality assessment of wind turbines is presented. Thirdly, an aggregate wind farm model that support power quality and stability analysis from large wind farms is presented. The aggregate wind farm model includes the smoothing of the relative power fluctuation from a wind farm compared to a single wind turbine. Finally, applications of the aggregate wind farm model to the power systems are presented. The power quality and stability characteristics influenced by large-scale wind power are illustrated with three cases. In this thesis, special emphasis has been given to appropriate models to represent the wind acting on wind farms. The wind speed model to a single wind turbine includes turbulence and tower shadow effects from the wind and the rotational sampling turbulence due to the rotation of the blades. In a park scale, the wind speed model to the wind farm includes the spatial coherence between different wind turbines. Here the wind speed model is applied to a constant rotational speed wind turbine/farm, but the model is suitable to variable speed wind turbine/farm as well. The cases presented here illustrate the influences of the wind power on the power system quality and stability. The flicker and frequency deviations are the main power quality parameters presented. The power system stability concentrates on the voltage stability and on the power system oscillations. From the cases studied, voltage and the frequency variations were smaller than expected from the large-scale wind power integration due to the low spatial correlation of the wind speed. The voltage quality analysed in a Brazilian power system and in the Nordel power system from connecting large

  4. Predicting the indicators of the safety performance monitoring after implementation of integrated management system (IMS in a combined cycle power plant in Yazd city

    Directory of Open Access Journals (Sweden)

    F. Laal

    2015-07-01

    .Conclusion: Findings show that Cubic regression can be an appropriate to olforinvestigating the indicators trends and for their predictionin planning and monitoring the performance ofsafety unitso that the decision-making for determining the priority of organizations’ safety programs would be facilitated.

  5. NASA's Radioisotope Power Systems - Plans

    Science.gov (United States)

    Hamley, John A.; Mccallum, Peter W.; Sandifer, Carl E., II; Sutliff, Thomas J.; Zakrajsek, June F.

    2015-01-01

    NASA's Radioisotope Power Systems (RPS) Program continues to plan and implement content to enable planetary exploration where such systems could be needed, and to prepare more advanced RPS technology for possible infusion into future power systems. The 2014-2015 period saw significant changes, and strong progress. Achievements of near-term objectives have enabled definition of a clear path forward in which payoffs from research investments and other sustaining efforts can be applied. The future implementation path is expected to yield a higher-performing thermoelectric generator design, a more isotope-fuel efficient system concept design, and a robust RPS infrastructure maintained effectively within both NASA and the Department of Energy. This paper describes recent work with an eye towards the future plans that result from these achievements.

  6. Advanced aircraft electric power system

    Energy Technology Data Exchange (ETDEWEB)

    Segrest, J.D.

    1981-01-01

    The role of electric energy in both military and commercial aircraft increases in importance with every advancement in airframe performance and avionic technology. Microcircuits and volatile memories impact power continuity and quality, digital flight control and stability augmentation require high reliability. This paper presents the system concept, hardware development and status of the Navy program.

  7. Intrusion Detection System: Security Monitoring System

    Directory of Open Access Journals (Sweden)

    ShabnamNoorani,

    2015-10-01

    Full Text Available An intrusion detection system (IDS is an ad hoc security solution to protect flawed computer systems. It works like a burglar alarm that goes off if someone tampers with or manages to get past other security mechanisms such as authentication mechanisms and firewalls. An Intrusion Detection System (IDS is a device or a software application that monitors network or system activities for malicious activities or policy violations and produces reports to a management station.Intrusion Detection System (IDS has been used as a vital instrument in defending the network from this malicious or abnormal activity..In this paper we are comparing host based and network based IDS and various types of attacks possible on IDS.

  8. Modeling of power electronic systems with EMTP

    Science.gov (United States)

    Tam, Kwa-Sur; Dravid, Narayan V.

    1989-01-01

    In view of the potential impact of power electronics on power systems, there is need for a computer modeling/analysis tool to perform simulation studies on power systems with power electronic components as well as to educate engineering students about such systems. The modeling of the major power electronic components of the NASA Space Station Freedom Electric Power System is described along with ElectroMagnetic Transients Program (EMTP) and it is demonstrated that EMTP can serve as a very useful tool for teaching, design, analysis, and research in the area of power systems with power electronic components. EMTP modeling of power electronic circuits is described and simulation results are presented.

  9. Power System Operation with Large Scale Wind Power Integration

    DEFF Research Database (Denmark)

    Suwannarat, A.; Bak-Jensen, B.; Chen, Z.

    2007-01-01

    to the uncertain nature of wind power. In this paper, proposed models of generations and control system are presented which analyze the deviation of power exchange at the western Danish-German border, taking into account the fluctuating nature of wind power. The performance of the secondary control of the thermal...... power plants and the spinning reserves control from the Combined Heat and Power (CHP) units to achieve active power balance with the increased wind power penetration is presented.......The Danish power system starts to face problems of integrating thousands megawatts of wind power, which produce in a stochastic behavior due to natural wind fluctuations. With wind power capacities increasing, the Danish Transmission System Operator (TSO) is faced with new challenges related...

  10. Using Data-Mining Approaches for Wind Turbine Power Curve Monitoring: A Comparative Study

    DEFF Research Database (Denmark)

    Schlechtingen, Meik; Santos, Ilmar; Achiche, Sofiane

    2013-01-01

    Four data-mining approaches for wind turbine power curve monitoring are compared. Power curve monitoring can be applied to evaluate the turbine power output and detect deviations, causing financial loss. In this research, cluster center fuzzy logic, neural network, and -nearest neighbor models...... are built and their performance compared against literature. Recently developed adaptive neuro-fuzzy-interference system models are set up and their performance compared with the other models, using the same data. Literature models often neglect the influence of the ambient temperature and the wind...... direction. The ambient temperature can influence the power output up to 20%. Nearby obstacles can lower the power output for certain wind directions. The approaches proposed in literature and the ANFIS models are compared by using wind speed only and two additional inputs. The comparison is based...

  11. Productivity Enhancement through Production Monitoring System

    OpenAIRE

    Prasad, Shiva H C; Rao, Potti Srinivasa; Gopalkrishna, B; Ahluwalia, Aakash

    2017-01-01

    A production monitoring system uses the real-time data while production is online. The real-time production monitoring systems are designed as means of auto data to the collection and monitoring the data via display boards. This study focuses on analysing the real-time production monitoring systems through trend analysis in production and over consumption of raw material controlling the over consumptions in a pen manufacturing industry. The methodology followed is through process flow diagram...

  12. Overvoltage Monitoring System for 500 kV Power Grid Based on Rogowski Coil%基于罗氏线圈原理的500kV电网过电压监测系统的研究

    Institute of Scientific and Technical Information of China (English)

    胡泉伟; 黄海波; 袁鹏; 寇小适; 李彦明; 范开元

    2011-01-01

    介绍了一种通过罗氏线圈传感器测量变压器套管末屏电流信号,经后续信号调理从而复原过电压信号的过电压监测系统.在分析了系统的可行性及组成方案优缺点的基础上,确定了系统的最终组成方案.设计了符合测量要求的罗氏线圈、三阶积分电路及触发电路,编写了基于LABVIEW语言的采集处理程序.系统动态响应试验表明,过电压监测系统可以准确地记录电网过电压波形,满足在线监测的要求.%An overvoltage monitoring system based on Rogowski coil was proposed, in which the current signal flowing through the tap of transformer hushing was measured by the coil and was subsequently processed and recovered into overvoltage signal. Consequently, a Rogowski coil meeting the measurement requirements, a third-order integral circuit, and a trigger circuit were designed, and an acquisition and process program was coded based on LABVIEW language for the system. The results show that the proposed system can accurately record the overvoltage waveforms of power grid and satisfy the requirements for monitoring power grid overvoltage.

  13. Evolutionary Autonomous Health Monitoring System (EAHMS) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — For supporting NASA's Robotics, Tele-Robotics and Autonomous Systems Roadmap, we are proposing the "Evolutionary Autonomous Health Monitoring System" (EAHMS) for...

  14. Geomagnetic disturbance effects on power systems

    Energy Technology Data Exchange (ETDEWEB)

    Albertson, V.D.; Bozoki, B.; Feero, W.E.; Kappenman, J.G.; Larsen, E.V.; Nordell, D.E.; Ponder, J.; Prabhakara, F.S.; Thompson, K.; Walling, R.

    1993-07-01

    In the northern hemisphere, the aurora borealis is visual evidence of simultaneous fluctuations in the earth's magnetic field (geomagnetic field). These geomagnetic disturbances (GMD's), or geomagnetic storms, can affect a number of man-made systems, including electric power systems. The GMD's are caused by the electromagnetic interaction of the solar wind plasma of protons and electrons with the geomagnetic field. These dynamic impulses in the solar wind are due to solar flares, coronal holes, and disappearing filaments, and reach the earth from one to six days after being emitted by a solar event. Instances of geomagnetic storms affecting telegraph systems were noted in England in 1846, and power system disturbances linked to GMD's were first reported in the United States in 1940. This Working Group report is a summary of the state of knowledge and research activity to the present time, and covers the GMD/Geomagnetically-induced currents (GIC) phenomena, transformer effects, the impact on generators, protective relay effects, and communication system effects. It also summarizes modeling and predicting GIC, measuring and monitoring GIC, mitigation methods, system operating guidelines during GMD's, and alerting and forecasting procedures and needs for the power industry.

  15. Handbook of power systems engineering with power electronics applications

    CERN Document Server

    Hase, Yoshihide

    2012-01-01

    Formerly known as Handbook of Power System Engineering, this second edition provides rigorous revisions to the original treatment of systems analysis together with a substantial new four-chapter section on power electronics applications. Encompassing a whole range of equipment, phenomena, and analytical approaches, this handbook offers a complete overview of power systems and their power electronics applications, and presents a thorough examination of the fundamental principles, combining theories and technologies that are usually treated in separate specialised fields, in a single u

  16. Bonneville, Power Administration Timing System

    Science.gov (United States)

    Martin, Kenneth E.

    1996-01-01

    Time is an integral part of the Bonneville Power Administration's (BPA) operational systems. Generation and power transfers are planned in advance. Utilities coordinate with each other by making these adjustments on a timed schedule. Price varies with demand, so billing is based on time. Outages for maintenance are scheduled to assure they do not interrupt reliable power delivery. Disturbance records are aligned with recorded timetags for analysis and comparison with related information. Advanced applications like traveling wave fault location and real-time phase measurement require continuous timing with high precision. Most of BPA is served by a Central Time System (CTS) at the Dittmer Control Center near Portland, OR. This system keeps time locally and supplies time to both the control center systems and field locations via a microwave signal. It is kept synchronized to national standard time and coordinated with interconnected utilities. It is the official BPA time. Powwer system control and operation is described, followed by a description of BPA timing systems including CTS, the Fault Location Acquisition Reporter, time dissemination, and phasor measurements. References are provided for further reading.

  17. Design Study of Nuclear Power Plant Severe Accidents Monitoring and Control System%核电厂严重事故监测和控制系统的设计研究

    Institute of Scientific and Technical Information of China (English)

    杜德君; 何庆镭

    2015-01-01

    HAF102-2004 "Nuclear power plant safety requirements for quality assurance" requires: besides of design reference, nuclear power plant design must consider the specific case beyond design reference, which includes the behavior of selected severe accidents. After the Fukushima accidents, each country pays more attention to sever accidents, the prevention and mitigation of severe accidents becomes one important point for the nuclear plant design. In the third generation nuclear power plant, the severe accidents monitoring and control system should be implemented to realize the function of prevention and mitigation for severe accidents.%HAF102-2004《核动力厂设计安全规定》中要求:除了设计基准外,设计中还必须考虑核动力厂在特定的超设计基准事故包括选定的严重事故中的行为。2011年福岛事故后,各国对严重事故更加关注,严重事故的预防和缓解成为核电厂设计中的一个重点。在三代核电厂设计中,增加了专门的严重事故监测和控制系统用来实现严重事故的预防和缓解功能。

  18. Power management for energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Gybel Hovgaard, T.

    2013-02-15

    In this thesis, we consider the control of two different industrial applications that belong at either end of the electricity grid; a power consumer in the form of a commercial refrigeration system, and wind turbines for power production. Our primary studies deal with economic model predictive control of a commercial multi-zone refrigeration system, consisting of several cooling units that share a common compressor, and is used to cool multiple areas or rooms, e.g., in supermarkets. For control of the commercial refrigeration application as well as the wind turbine application, we propose an economic optimizing model predictive controller, economic MPC. Our investigations are primarily concerned with: 1) modeling of the applications to suit the chosen control framework; 2) formulating the MPC controller laws to overcome challenges introduced by the industrial applications, and defining economic objectives that reect the real physics of the systems as well as our control objectives; 3) solving the involved, non-trivial optimization problems eciently in real-time; 4) demonstrating the feasibility and potential of the proposed methods by extensive simulation and comparison with existing control methods and evaluation of data from systems in actual operation. We demonstrate, i.a., substantial cost savings, on the order of 30 %, compared to a standard thermostat-based supermarket refrigeration system and show how our methods exhibit sophisticated demand response to real-time variations in electricity prices. Violations of the temperature ranges can be kept at a very low frequency of occurrence inspite of the presence of uncertainty. For the power output from wind turbines, ramp rates, as low a 3 % of the rated power per minute, can be effectively ensured with the use of energy storage and we show how the active use of rotor inertia as an additional energy storage can reduce the needed storage capacity by up to 30 % without reducing the power output. (Author)

  19. An Online Monitoring and Fault Location Methodology for Underground Power Cables

    Science.gov (United States)

    Govindarajan, Sudarshan

    With the growing importance of underground power systems and the need for greater reliability of the power supply, cable monitoring and accurate fault location detection has become an increasingly important issue. The presence of inherent random fluctuations in power system signals can be used to extract valuable information about the condition of system equipment. One such component is the power cable, which is the primary focus of this research. This thesis investigates a unique methodology that allows online monitoring of an underground power cable. The methodology analyzes conventional power signals in the frequency domain to monitor the condition of a power cable. First, the proposed approach is analyzed theoretically with the help of mathematical computations. Frequency domain analysis techniques are then used to compute the power spectral density (PSD) of the system signals. The importance of inherent noise in the system, a key requirement of this methodology, is also explained. The behavior of resonant frequencies, which are unique to every system, are then analyzed under different system conditions with the help of mathematical expressions. Another important aspect of this methodology is its ability to accurately estimate cable fault location. The process is online and hence does not require the system to be disconnected from the grid. A single line to ground fault case is considered and the trend followed by the resonant frequencies for different fault positions is observed. The approach is initially explained using theoretical calculations followed by simulations in MATLAB/Simulink. The validity of this technique is proved by comparing the results obtained from theory and simulation to actual measurement data.

  20. In Vivo Self-Powered Wireless Cardiac Monitoring via Implantable Triboelectric Nanogenerator.

    Science.gov (United States)

    Zheng, Qiang; Zhang, Hao; Shi, Bojing; Xue, Xiang; Liu, Zhuo; Jin, Yiming; Ma, Ye; Zou, Yang; Wang, Xinxin; An, Zhao; Tang, Wei; Zhang, Wei; Yang, Fan; Liu, Yang; Lang, Xilong; Xu, Zhiyun; Li, Zhou; Wang, Zhong Lin

    2016-07-26

    Harvesting biomechanical energy in vivo is an important route in obtaining sustainable electric energy for powering implantable medical devices. Here, we demonstrate an innovative implantable triboelectric nanogenerator (iTENG) for in vivo biomechanical energy harvesting. Driven by the heartbeat of adult swine, the output voltage and the corresponding current were improved by factors of 3.5 and 25, respectively, compared with the reported in vivo output performance of biomechanical energy conversion devices. In addition, the in vivo evaluation of the iTENG was demonstrated for over 72 h of implantation, during which the iTENG generated electricity continuously in the active animal. Due to its excellent in vivo performance, a self-powered wireless transmission system was fabricated for real-time wireless cardiac monitoring. Given its outstanding in vivo output and stability, iTENG can be applied not only to power implantable medical devices but also possibly to fabricate a self-powered, wireless healthcare monitoring system.

  1. A portable power system using PEM fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Long, E. [Ball Aerospace and Technologies Corp., Boulder, CO (United States)

    1997-12-31

    Ball has developed a proof-of-concept, small, lightweight, portable power system. The power system uses a proton exchange membrane (PEM) fuel cell stack, stored hydrogen, and atmospheric oxygen as the oxidant to generate electrical power. Electronics monitor the system performance to control cooling air and oxidant flow, and automatically do corrective measures to maintain performance. With the controller monitoring the system health, the system can operate in an ambient environment from 0 C to +50 C. The paper describes system testing, including load testing, thermal and humidity testing, vibration and shock testing, field testing, destructive testing of high-pressure gas tanks, and test results on the fuel cell power system, metal hydride hydrogen storage, high-pressure hydrogen gas storage, and chemical hydride hydrogen storage.

  2. Implementation of a worth-oriented monitoring system by means of a medium-sized power supply company; Implementierung eines wertorientierten Steuerungssystems inklusive Beispiel anhand eines mittelgrossen Energieversorgungsunternehmens

    Energy Technology Data Exchange (ETDEWEB)

    Mierzwa, Thomas

    2009-07-01

    The book under consideration reports on a systematization as well as on a theoretical presentation of existing worth-oriented control concepts. The author points out the computation as well as the possibility of an implementation of worth-orientated sizes on the basis of an exemplary power supply company.

  3. Research of on-line monitoring method for insulation condition of power transformer bushing

    Science.gov (United States)

    Xia, Jiuyun; Qian, Zheng; Yu, Hao; Yao, Junda

    2016-01-01

    The power transformer is the key equipment of the power system; its insulation condition will directly influence the security and reliability of the power system. Thus, the on-line monitoring of power transformer is urgently required in order to guarantee the normal operation of the power system. Moreover, the dielectric loss factor is a significant parameter reflecting the condition of transformer bushing, so the on-line measurement of dielectric loss factor is really important. In this paper, the phase-to-phase comparison method is selected as the on-line monitoring method based on the overall analysis and discussion of the existing on-line monitoring methods. At first, the harmonic analysis method is utilized to calculate the dielectric loss of each phase of the three-phase transformer bushing, and then the differences of dielectric loss between every two phases are calculated and analyzed. So the insulation condition of each bushing could be achieved based on the careful analysis of different phase-to-phase dielectric loss. The simulation results of phase-to-phase comparison method are carried out in this paper, and the validity is verified. At last, this method is utilized in an actual equipment of on-line monitoring.

  4. Beamlet pulsed-power system

    Energy Technology Data Exchange (ETDEWEB)

    Larson, D.

    1996-06-01

    The 13-MJ Beamlet pulsed-power system provides power to the 512 flash lamps in the cavity and booster amplifiers. Since the flash lamps pump all of the apertures in the 2 x 2 amplifier array, the capacitor bank provides roughly four times the energy required to pump the single active beam line. During the 40 s prior to the shot, the capacitors are charged by constant-current power supplies. Ignitron switches transfer the capacitor energy to the flash lamps via coaxial cables. A preionization system triggers the flash lamps and delivers roughly 1 % of the capacitor energy 200 {mu}s prior to the main discharge. This is the first time flash-lamp preionization has been used in a large facility. Preionization improves the amplifier efficiency by roughly 5% and increases the lifetime of the flash lamps. LabVIEW control panels provide an operator interface with the modular controls and diagnostics. To improve the reliability of the system, high-energy-density, self-healing, metallized dielectric capacitors are used. High-frequency, voltage-regulated switching power supplies are integrated into each module on Beamlet, allowing greater independence among the modules and improved charge voltage accuracy, flexibility, and repeatability.

  5. Electric Vehicles in Power Systems with 50% Wind Power Penetration

    DEFF Research Database (Denmark)

    Østergaard, Jacob; Foosnæs, Anders; Xu, Zhao

    2009-01-01

    . This paper analyse the potential for using EVs in Denmark and identify the benefits of the electric power system with high wind power generation by intelligent charging of the EVs. Based on the analysis important technology gabs are identified, and the corresponding research and development initiatives...... will be an important balancing measure to enable the Danish government’s energy strategy, which implies 50% wind power penetration in the electric power system. An EV will be a storage device for smoothing power fluctuations from renewable resources especially wind power and provide valuable system services...... for a reliable power system operation. Cost-benefit analysis shows that intelligent bidirectional charging – vehicle to grid (V2G) – provides a socio-economic profit of 150 million Euro/year in the Danish electric power system in 2025 assuming that 15% of the Danish road transport need is supplied by electricity...

  6. Power system dynamics and control

    CERN Document Server

    Kwatny, Harry G

    2016-01-01

    This monograph explores a consistent modeling and analytic framework that provides the tools for an improved understanding of the behavior and the building of efficient models of power systems. It covers the essential concepts for the study of static and dynamic network stability, reviews the structure and design of basic voltage and load-frequency regulators, and offers an introduction to power system optimal control with reliability constraints. A set of Mathematica tutorial notebooks providing detailed solutions of the examples worked-out in the text, as well as a package that will enable readers to work out their own examples and problems, supplements the text. A key premise of the book is that the design of successful control systems requires a deep understanding of the processes to be controlled; as such, the technical discussion begins with a concise review of the physical foundations of electricity and magnetism. This is followed by an overview of nonlinear circuits that include resistors, inductors, ...

  7. 基于GSM的短信息的电源监控系统的设计%Design of monitor system of power supply for short message based on GSM

    Institute of Scientific and Technical Information of China (English)

    王文亮; 冀文超

    2011-01-01

    With the development of GSM, short message is developing very quickly and widely as a simple and convenient ways of data communicalion. The structure and the design proposal of the power source monitor system based on GSM were introduced. and a real time and accurate monitoring by existing GMS network resources was carried out The system is suitable to the field which requires less data transmission and dispersed detected point%随着GSM网络的发展,短信息作为GSM系统中最为简单和方便的数据通信方式,得到了迅猛的发展.介绍了基于短消息业务的电源监控系统的组成结构和设计方案,利用了GSM移动通讯网络短信息服务快捷的性能对电源进行实时、准确的监控.该系统对于监测点分散,数据传送量较少,需要监控的领域具有较大的实用价值.

  8. Standard hydrogen monitoring system equipment installation instructions

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, T.C.

    1996-09-27

    This document provides the technical specifications for the equipment fabrication, installation, and sitework construction for the Standard Hydrogen Monitoring System. The Standard Hydrogen Monitoring System is designed to remove gases from waste tank vapor space and exhaust headers for continual monitoring and remote sample analysis.

  9. Dynamic Influences of Wind Power on The Power System

    DEFF Research Database (Denmark)

    Rosas, Pedro Andrè Carvalho

    2004-01-01

    The thesis first presents the basic influences of wind power on the power system stability and quality by pointing out the main power quality issues of wind power in a small-scale case and following, the expected large-scale problems are introduced.Secondly, a dynamic wind turbine model...... to a single wind turbine. Finally, applications of the aggregate wind farm model to the power systems are presented. The power quality and stabilitycharacteristics influenced by large-scale wind power are illustrated with three cases. In this thesis, special emphasis has been given to appropriate models...... that supports power quality assessment of wind turbines is presented. Thirdly, an aggregate wind farm model that support power quality and stability analysis from large wind farms is presented. The aggregate windfarm model includes the smoothing of the relative power fluctuation from a wind farm compared...

  10. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2004-01-09

    The objective of this program is to develop a system to both monitor the vibration of a bottomhole assembly, and to adjust the properties of an active damper in response to these measured vibrations. Phase I of this program entails modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype. The project continues to advance, but is behind the revised (14-month) schedule. Tasks 1-3 (Modeling, Specification and Design) are all essentially complete. The test bench for the Test and Evaluation (Tasks 4 & 5) has been designed and constructed. The design of the full-scale laboratory prototype and associated test equipment is complete and the components are out for manufacture. Barring any unforeseen difficulties, laboratory testing should be complete by the end of March, as currently scheduled. We anticipate the expenses through March to be approximately equal to those budgeted for Phase I.

  11. 78 FR 62616 - Integrated System Power Rates

    Science.gov (United States)

    2013-10-22

    ... Southwestern Power Administration Integrated System Power Rates AGENCY: Southwestern Power Administration, DOE... Integrated System pursuant to the Integrated System Rate Schedules to supersede the existing rate schedules... into effect on an interim basis, increases the power rates for the Integrated System pursuant to...

  12. 75 FR 1363 - Integrated System Power Rates

    Science.gov (United States)

    2010-01-11

    ... Southwestern Power Administration Integrated System Power Rates AGENCY: Southwestern Power Administration, DOE... System pursuant to the following Integrated System Rate Schedules: Rate Schedule P-09, Wholesale Rates...) Administrator has determined based on the 2009 Integrated System Current Power Repayment Study, that...

  13. Use of simulators for validation of advanced plant monitoring systems

    Energy Technology Data Exchange (ETDEWEB)

    Uytterhoeven, G.; Vlaminck, M. De [Belgatom, Brussels (Belgium); Javaux, D. [Cognitive Ergonomics Work-Psychology Department, University of Liege, Sart-Tilman (Belgium)

    1999-07-01

    This paper describes how the full-scope nuclear power plant simulator of Doel (Belgium) was used to assess Situation Awareness for the validation of a process monitoring and supervision system, named DIMOS. The method (derived from a method originally developed for the aerospace industry) has been adapted and applied to compare the efficiency of two versions of the monitoring system: Alarm-masking and non alarm-masking versions of DIMOS have been analysed in their ability to support Situation Awareness, to improve performance and to fulfil the satisfaction of operators. Both normal power plant operating conditions and abnormal operating conditions were simulated and a large number of power plant operators were involved in the evaluation. The paper focuses on the rationale behind the 'Situation Awareness' evaluation, the experiment environment and the results regarding the added value of the alarm masking version of the monitoring system. (author)

  14. Accounting for complementarity to maximize monitoring power for species management.

    Science.gov (United States)

    Tulloch, Ayesha I T; Chadès, Iadine; Possingham, Hugh P

    2013-10-01

    To choose among conservation actions that may benefit many species, managers need to monitor the consequences of those actions. Decisions about which species to monitor from a suite of different species being managed are hindered by natural variability in populations and uncertainty in several factors: the ability of the monitoring to detect a change, the likelihood of the management action being successful for a species, and how representative species are of one another. However, the literature provides little guidance about how to account for these uncertainties when deciding which species to monitor to determine whether the management actions are delivering outcomes. We devised an approach that applies decision science and selects the best complementary suite of species to monitor to meet specific conservation objectives. We created an index for indicator selection that accounts for the likelihood of successfully detecting a real trend due to a management action and whether that signal provides information about other species. We illustrated the benefit of our approach by analyzing a monitoring program for invasive predator management aimed at recovering 14 native Australian mammals of conservation concern. Our method selected the species that provided more monitoring power at lower cost relative to the current strategy and traditional approaches that consider only a subset of the important considerations. Our benefit function accounted for natural variability in species growth rates, uncertainty in the responses of species to the prescribed action, and how well species represent others. Monitoring programs that ignore uncertainty, likelihood of detecting change, and complementarity between species will be more costly and less efficient and may waste funding that could otherwise be used for management. © 2013 Society for Conservation Biology.

  15. Power system dynamics and stability with synchrophasor measurement and power system toolbox

    CERN Document Server

    Sauer, Peter W; Chow, Joe H

    2017-01-01

    This new edition addresses the needs of dynamic modeling and simulation relevant to power system planning, design, and operation, including a systematic derivation of synchronous machine dynamic models together with speed and voltage control subsystems. Reduced-order modeling based on integral manifolds is used as a firm basis for understanding the derivations and limitations of lower-order dynamic models. Following these developments, a multi-machine model interconnected through the transmission network is formulated and simulated using numerical simulation methods. Energy function methods are discussed for direct evaluation of stability. Small-signal analysis is used for determining the electromechanical modes and mode-shapes, and for power system stabilizer design. Time-synchronized high-sampling-rate phasor measurement units (PMUs) to monitor power system disturbances ave been implemented throughout North America and many other countries. In this second edition, new chapters on synchrophasor measurement ...

  16. Distribution of the 134Cs/137Cs ratio around the Fukushima Daiichi nuclear power plant using an unmanned helicopter radiation monitoring system

    Science.gov (United States)

    Torii, T.; Nishizawa, Y.

    2015-12-01

    Many radioactive substances were released by the Fukushima Daiichi nuclear power plant accident occurred on March 11, 2011 in the atmosphere. A lot of short half-life nuclides which are 131I, 132Te (132I) and 133I, etc., in addition to longer half-lived nuclides such as 134Cs and 137Cs. The estimated release amount of these nuclides from the reactor 1st to 3rd unit is reported, but it's found to be quite different in the short half-lived nuclides by the reactor units. Because the radioactivity ratio of 134Cs and 137Cs was slight different between the reactor units, it can be considered that the valuable source is obtained by the measurement of 134Cs/137Cs ratio in the environment around the Fukushima Daiichi nuclear power station at the present stage when the nuclides with short half-lives had already decayed. We have measured high-resolution gamma-ray spectrum using an unmanned helicopter equipped with LaBr3(Ce) detector in a 3-km range from the power station which was near to the release source of the radioactive cesium. Because the LaBr3(Ce) detector has high resolution of gamma rays, the discrimination of many nuclides is possible. In addition, there is extremely much number of the data provided by the distribution measurement with the unmanned helicopter. Because a new map was illustrated by the analysis of the 134Cs/137Cs ratio, we report the outline.

  17. Non-intrusive Methods for Mode Estimation in Power Systems using Synchrophasors

    NARCIS (Netherlands)

    Perić, V.

    2016-01-01

    The power system industry has been going through dynamic infrastructural and operational changes in recent years that have caused more prominent lightly damped electromechanical oscillations. Real-time monitoring of electromechanical oscillations is of great significance for power system operators;

  18. Non-intrusive Methods for Mode Estimation in Power Systems using Synchrophasors

    NARCIS (Netherlands)

    Perić, V.

    2016-01-01

    The power system industry has been going through dynamic infrastructural and operational changes in recent years that have caused more prominent lightly damped electromechanical oscillations. Real-time monitoring of electromechanical oscillations is of great significance for power system operators;

  19. OVERLOAD CAPABILITY OF POWER CABLES IN ACTUAL POWER CONSUMPTION SYSTEMS

    Directory of Open Access Journals (Sweden)

    L.A. Szhebenyuk

    2013-09-01

    Full Text Available Results of overload capability calculations for 6-kV power cables are analyzed. The work is aimed at creating a computation system for the current rating of high-voltage cross-linked polyethylene power cables.

  20. A Dual-Core System Solution for Wearable Health Monitors

    NARCIS (Netherlands)

    Santana Arnaiz, O.A.; Bouwens, F.; Huisken, J.A.; De Groot, H.; Bennebroek, M.T.; Van Meerbergen, J.L.; Abbo, A.A.; Fraboulet, A.

    2011-01-01

    This paper presents a system design study for wearable sensor devices intended for healthcare and lifestyle applications based on ECG,EEG and activity monitoring. In order to meet the low-power requirement of these applications, a dual-core signal processing system is proposed which combines an ultr

  1. Uncertainty Quantification Techniques for Sensor Calibration Monitoring in Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Ramuhalli, Pradeep; Lin, Guang; Crawford, Susan L.; Konomi, Bledar A.; Braatz, Brett G.; Coble, Jamie B.; Shumaker, Brent; Hashemian, Hash

    2013-09-01

    This report describes the status of ongoing research towards the development of advanced algorithms for online calibration monitoring. The objective of this research is to develop the next generation of online monitoring technologies for sensor calibration interval extension and signal validation in operating and new reactors. These advances are expected to improve the safety and reliability of current and planned nuclear power systems as a result of higher accuracies and increased reliability of sensors used to monitor key parameters. The focus of this report is on documenting the outcomes of the first phase of R&D under this project, which addressed approaches to uncertainty quantification (UQ) in online monitoring that are data-driven, and can therefore adjust estimates of uncertainty as measurement conditions change. Such data-driven approaches to UQ are necessary to address changing plant conditions, for example, as nuclear power plants experience transients, or as next-generation small modular reactors (SMR) operate in load-following conditions.

  2. Uncertainty Quantification Techniques for Sensor Calibration Monitoring in Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Ramuhalli, Pradeep; Lin, Guang; Crawford, Susan L.; Konomi, Bledar A.; Coble, Jamie B.; Shumaker, Brent; Hashemian, Hash

    2014-04-30

    This report describes research towards the development of advanced algorithms for online calibration monitoring. The objective of this research is to develop the next generation of online monitoring technologies for sensor calibration interval extension and signal validation in operating and new reactors. These advances are expected to improve the safety and reliability of current and planned nuclear power systems as a result of higher accuracies and increased reliability of sensors used to monitor key parameters. The focus of this report is on documenting the outcomes of the first phase of R&D under this project, which addressed approaches to uncertainty quantification (UQ) in online monitoring that are data-driven, and can therefore adjust estimates of uncertainty as measurement conditions change. Such data-driven approaches to UQ are necessary to address changing plant conditions, for example, as nuclear power plants experience transients, or as next-generation small modular reactors (SMR) operate in load-following conditions.

  3. Prometheus: a next-generation monitoring system

    CERN Document Server

    CERN. Geneva

    2017-01-01

    Prometheus is an open eco-system that provides an end-to-end approach to infrastructure and application monitoring. It covers all levels beginning with easy instrumentation based on a flexible, multi-dimensional data model. The Prometheus server itself collects and stores time series while trying to maintain operational simplicity while being adaptable to varying scales and layouts of infrastructure. By integrating with a wide range of service discovery systems, it always stays in sync with the world it is monitoring. The powerful query language allows us to ask complex questions and can be applied seamlessly between ad-hoc investigation and static dashboarding. It is also directly applied in the eco-system's alerting layer, which favors a time-series based over and event driven approach. In this talk we will look at all aspects of Prometheus from the high-level philosophy behind its design to its practical concerns of implementation and operation. About the speaker Fabian Reinartz is a software eng...

  4. Remote Power Control of Ethernet PON System

    Institute of Scientific and Technical Information of China (English)

    Inkwun Jung; Chunghwan Lim; Youngil Park

    2003-01-01

    A power control scheme to make all ONU channels’ power received at OLT nearly equal is proposed. Implemented by monitoring powers at OLT and sending control message to each ONU, it helps data recovery from the burst type upstream optical signals.

  5. Remote Power Control of Ethernet PON System

    Institute of Scientific and Technical Information of China (English)

    Inkwun; Jung; Chunghwan; Lim; Youngil; Park

    2003-01-01

    A power control scheme to make all ONU channels' power received at OLT nearly equal is proposed. Implemented by monitoring powers at OLT and sending control message to each ONU, it helps data recovery from the burst type upstream optical signals.

  6. Radioisotope Power System Pool Concept

    Science.gov (United States)

    Rusick, Jeffrey J.; Bolotin, Gary S.

    2015-01-01

    Advanced Radioisotope Power Systems (RPS) for NASA deep space science missions have historically used static thermoelectric-based designs because they are highly reliable, and their radioisotope heat sources can be passively cooled throughout the mission life cycle. Recently, a significant effort to develop a dynamic RPS, the Advanced Stirling Radioisotope Generator (ASRG), was conducted by NASA and the Department of Energy, because Stirling based designs offer energy conversion efficiencies four times higher than heritage thermoelectric designs; and the efficiency would proportionately reduce the amount of radioisotope fuel needed for the same power output. However, the long term reliability of a Stirling based design is a concern compared to thermoelectric designs, because for certain Stirling system architectures the radioisotope heat sources must be actively cooled via the dynamic operation of Stirling converters throughout the mission life cycle. To address this reliability concern, a new dynamic Stirling cycle RPS architecture is proposed called the RPS Pool Concept.

  7. Power system applications for PASC converter systems

    Energy Technology Data Exchange (ETDEWEB)

    Donnelly, M.K. [Pacific Northwest Lab., Richland, WA (United States); Johnson, R.M. [Montana State Univ., Bozeman, MT (United States)

    1994-04-01

    This paper shows, using computer EMTP simulations, some preliminary results of applying pulse amplitude synthesis and control (PASC) technology to single-source level voltage converter system. The method can be applied to any single terminal pair source with appropriate modifications in power extraction interface and computer control program to match source and load impedance characteristics. The PASC realization as discussed here employs banks of transformers, one bank per phase, in which the primaries are connected in parallel through a switch matrix to the dc source. Two opposite polarity primaries per transformer are pulsed alternatively in time to produce an oscillatory sinusoidal output waveform. PASC conversion system capabilities to produce both leading and lagging power factor power output in single-phase and three-phase {Delta} or Y configurations are illustrated. EMTP simulations are used to demonstrate the converter capabilities. Also included are discussions regarding harmonics and potential control strategies to adapt the converter to an application or to minimize harmonics.

  8. Robust power system frequency control

    CERN Document Server

    Bevrani, Hassan

    2014-01-01

    This updated edition of the industry standard reference on power system frequency control provides practical, systematic and flexible algorithms for regulating load frequency, offering new solutions to the technical challenges introduced by the escalating role of distributed generation and renewable energy sources in smart electric grids. The author emphasizes the physical constraints and practical engineering issues related to frequency in a deregulated environment, while fostering a conceptual understanding of frequency regulation and robust control techniques. The resulting control strategi

  9. Knolls Atomic Power Laboratory environmental monitoring report, calendar year 2000

    Energy Technology Data Exchange (ETDEWEB)

    None

    2001-12-01

    The results of the effluent and environmental monitoring programs at the three Knolls Atomic Power Laboratory (KAPL) Sites are summarized and assessed in this report. Operations at the Knolls Site, Niskayuna, New York and the Kesselring Site, West Milton, New York and site closure activities at the S1C Site, Windsor, Connecticut, continued to have no adverse effect on human health and the quality of the environment during calendar year 2000. The effluent and environmental monitoring programs conducted by KAPL are designed to determine the effectiveness of treatment and control methods, to provide measurement of the concentrations in effluents for comparison with applicable standards, and to assess resultant concentrations in the environment. The monitoring programs include analyses of samples of liquid and gaseous effluents for chemical constituents and radioactivity as well as monitoring of environmental air, water, sediment, and fish. Radiation measurements are also made around the perimeter of each Site and at off-site background locations. Monitoring programs at the S1C Site were reduced in scope during calendar year 2000 due to completion of site dismantlement activities during 1999.

  10. Knolls Atomic Power Laboratory environmental monitoring report, calendar year 2001

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-12-31

    The results of the effluent and environmental monitoring programs at the three Knolls Atomic Power Laboratory (KAPL) Sites are summarized and assessed in this report. Operations at the Knolls and Kesselring Sites and Site closure activities at the S1C Site (also known as the KAPL Windsor Site) continue to have no adverse effect on human health and the quality of the environment. The effluent and environmental monitoring programs conducted by KAPL at the Knolls and Kesselring Sites are designed to determine the effectiveness of treatment and control methods, to provide measurement of the concentrations in effluents for comparison with applicable standards, and to assess resultant concentrations in the environment. The monitoring programs include analyses of samples of liquid and gaseous effluents for chemical constituents and radioactivity as well as environmental monitoring of air, water, sediment, and fish. Radiation measurements are also made around the perimeter of the Knolls and Kesselring Sites and at off-site background locations. The environmental monitoring program for the S1C Site continues to be reduced in scope from previous years due to the completion of Site dismantlement activities during 1999 and a return to green field conditions during 2000.

  11. Remote monitoring of LED lighting system performance

    Science.gov (United States)

    Thotagamuwa, Dinusha R.; Perera, Indika U.; Narendran, Nadarajah

    2016-09-01

    The concept of connected lighting systems using LED lighting for the creation of intelligent buildings is becoming attractive to building owners and managers. In this application, the two most important parameters include power demand and the remaining useful life of the LED fixtures. The first enables energy-efficient buildings and the second helps building managers schedule maintenance services. The failure of an LED lighting system can be parametric (such as lumen depreciation) or catastrophic (such as complete cessation of light). Catastrophic failures in LED lighting systems can create serious consequences in safety critical and emergency applications. Therefore, both failure mechanisms must be considered and the shorter of the two must be used as the failure time. Furthermore, because of significant variation between the useful lives of similar products, it is difficult to accurately predict the life of LED systems. Real-time data gathering and analysis of key operating parameters of LED systems can enable the accurate estimation of the useful life of a lighting system. This paper demonstrates the use of a data-driven method (Euclidean distance) to monitor the performance of an LED lighting system and predict its time to failure.

  12. Long endurance underwater power system

    Science.gov (United States)

    1989-01-01

    The development and design of deep sea power sources for long endurances (more than 1 year) and moderate power (more than 1 KW) are unique. The best primary battery (Li-thionyl chloride) would involve huge space and weight and the cost of such a system would be prohibitive. Fuel cells with stored gases need a pressure vessel and also quite a large volume and weight. Aquanautics is engaged in developing a power source to a very demanding design. The design would involve a completely open system eliminating the need for a pressure vessel. Aquanautics will capture oxygen from the seawater to be delivered to a fuel cell. The hydrogen generated in this design is envisioned to be from a reaction between aluminum and seawater. Such a completely open system is already available from Alupower, Inc. This provides for a much safer and more compact design than cryogenic hydrogen. Lithium or magnesium can also be used. Both are expensive and lithium is known to be potentially hazardous. Since the last report, there has been major improvement of the technological issue of carrier longevity. The previous carrier had an operational life of 3 days. At present, Aquanautics has discovered a carrier called 23SuzyP which has stable electrochemical performance for over a month.

  13. BWR online monitoring system based on noise analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz-Villafuerte, Javier [Departamento de Sistemas Nucleares, Instituto Nacional de Investigaciones Nucleares, Carr. Mexico-Toluca S/N, Ocoyoacac, Edo. de Mexico, 52750 (Mexico)]. E-mail: jov@nuclear.inin.mx; Castillo-Duran, Rogelio [Departamento de Sistemas Nucleares, Instituto Nacional de Investigaciones Nucleares, Carr. Mexico-Toluca S/N, Ocoyoacac, Edo. de Mexico, 52750 (Mexico)]. E-mail: rcd@nuclear.inin.mx; Alonso, Gustavo [Departamento de Sistemas Nucleares, Instituto Nacional de Investigaciones Nucleares, Carr. Mexico-Toluca S/N, Ocoyoacac, Edo. de Mexico, 52750 (Mexico)]. E-mail: galonso@nuclear.inin.mx; Calleros-Micheland, Gabriel [Central Nuclear de Laguna Verde, Comision Federal de Electricidad, Carr. Cardel-Nautla, km. 42.5, Alto Lucero, Veracruz (Mexico)]. E-mail: gcm9acpp@cfe.gob.mx

    2006-11-15

    A monitoring system for during operation early detection of an anomaly and/or faulty behavior of equipment and systems related to the dynamics of a boiling water reactor (BWR) has been developed. The monitoring system is based on the analysis of the 'noise' or fluctuations of a signal from a sensor or measurement device. An efficient prime factor algorithm to compute the fast Fourier transform allows the continuous, real-time comparison of the normalized power spectrum density function of the signal against previously stored reference patterns in a continuously evolving matrix. The monitoring system has been successfully tested offline. Four examples of the application of the monitoring system to the detection and diagnostic of faulty equipment behavior are presented in this work: the detection of two different events of partial blockage at the jet pump inlet nozzle, miss-calibration of a recirculation mass flow sensor, and detection of a faulty data acquisition card. The events occurred at the two BWR Units of the Laguna Verde Nuclear Power Plant. The monitoring system and its possible coupling to the data and processing information system of the Laguna Verde Nuclear Power Plant are described. The signal processing methodology is presented along with the introduction of the application of the evolutionary matrix concept for determining the base signature of reactor equipment or component and the detection of off normal operation conditions.

  14. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2005-01-28

    The objective of this program is to develop a system to both monitor the vibration of a bottomhole assembly, and to adjust the properties of an active damper in response to these measured vibrations. Phase I of this program, which entailed modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype, was completed on May 31, 2004. The principal objectives of Phase II are: more extensive laboratory testing, including the evaluation of different feedback algorithms for control of the damper; design and manufacture of a field prototype system; and, testing of the field prototype in drilling laboratories and test wells. The redesign and upgrade of the laboratory prototype was completed on schedule and it was assembled during the last period. Testing was begin during the first week of October. Initial results indicated that the dynamic range of the damping was less than predicted and that the maximum damping was also less than required. A number of possible explanations for these results were posited, and test equipment was acquired to evaluate the various hypotheses. Testing was just underway at the end of this period.

  15. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2004-10-29

    The objective of this program is to develop a system to both monitor the vibration of a bottomhole assembly, and to adjust the properties of an active damper in response to these measured vibrations. Phase I of this program, which entailed modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype, was completed on May 31, 2004. Phase II began on June 1, and the first month's effort were reported in the seventh quarterly report on the project.1 The principal objectives of Phase II are: more extensive laboratory testing, including the evaluation of different feedback algorithms for control of the damper; design and manufacture of a field prototype system; and, testing of the field prototype in drilling laboratories and test wells. The redesign and upgrade of the laboratory prototype was completed on schedule during this period, and assembly was complete at the end of this period. Testing will begin during the first week of October. This aspect of the project is thus approximately six weeks behind schedule. Design of the field prototype is progressing per schedule.

  16. Self-powered Real-time Movement Monitoring Sensor Using Triboelectric Nanogenerator Technology.

    Science.gov (United States)

    Jin, Liangmin; Tao, Juan; Bao, Rongrong; Sun, Li; Pan, Caofeng

    2017-09-05

    The triboelectric nanogenerator (TENG) has great potential in the field of self-powered sensor fabrication. Recently, smart electronic devices and movement monitoring sensors have attracted the attention of scientists because of their application in the field of artificial intelligence. In this article, a TENG finger movement monitoring, self-powered sensor has been designed and analysed. Under finger movements, the TENG realizes the contact and separation to convert the mechanical energy into electrical signal. A pulse output current of 7.8 μA is generated by the bending and straightening motions of the artificial finger. The optimal output power can be realized when the external resistance is approximately 30 MΩ. The random motions of the finger are detected by the system with multiple TENG sensors in series. This type of flexible and self-powered sensor has potential applications in artificial intelligence and robot manufacturing.

  17. Virtual instrument for controlling and monitoring digitalized power supply in SSRF

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The Shanghai Synchrotron Radiation Facility (SSRF) needs extremely precise power supplies for their various magnets. A digital controller is being developed for the power converters of the SSRF power supply (PS). In the digital controller, a fully digital pulse-width modulator (PWM) directly controls the power unit insulated gate bipolar transistor (IGBT) of the PS. A program in LabVIEW language has been developed to control and monitor the digital PS via serial communication (RS232) from a PC and to modify its parameters as well. In this article, the software design of the virtual instrument for controlling and monitoring digitalized PS and its associated functions are described, and the essential elements of the program graphical main-Ⅵ and sub-Ⅵ source code are presented and explained. The communication protocol and the structure of the developed system are also included in this article.

  18. Review of Power System Stability with High Wind Power Penetration

    DEFF Research Database (Denmark)

    Hu, Rui; Hu, Weihao; Chen, Zhe

    2015-01-01

    analyzing methods and stability improvement approaches. With increasing wind power penetration, system balancing and the reduced inertia may cause a big threaten for stable operation of power systems. To mitigate or eliminate the wind impacts for high wind penetration systems, although the practical......This paper presents an overview of researches on power system stability with high wind power penetration including analyzing methods and improvement approaches. Power system stability issues can be classified diversely according to different considerations. Each classified issue has special...... and reliable choices currently are the strong outside connections or sufficient reserve capacity constructions, many novel theories and approaches are invented to investigate the stability issues, looking forward to an extra-high penetration or totally renewable resource based power systems. These analyzing...

  19. Monitored Geologic Repository Operations Monitoring and Control System Description Document

    Energy Technology Data Exchange (ETDEWEB)

    E.F. Loros

    2000-06-29

    The Monitored Geologic Repository Operations Monitoring and Control System provides supervisory control, monitoring, and selected remote control of primary and secondary repository operations. Primary repository operations consist of both surface and subsurface activities relating to high-level waste receipt, preparation, and emplacement. Secondary repository operations consist of support operations for waste handling and treatment, utilities, subsurface construction, and other selected ancillary activities. Remote control of the subsurface emplacement operations, as well as, repository performance confirmation operations are the direct responsibility of the system. In addition, the system monitors parameters such as radiological data, air quality data, fire detection status, meteorological conditions, unauthorized access, and abnormal operating conditions, to ensure a safe workplace for personnel. Parameters are displayed in a real-time manner to human operators regarding surface and subsurface conditions. The system performs supervisory monitoring and control for both important to safety and non-safety systems. The system provides repository operational information, alarm capability, and human operator response messages during emergency response situations. The system also includes logic control to place equipment, systems, and utilities in a safe operational mode or complete shutdown during emergency response situations. The system initiates alarms and provides operational data to enable appropriate actions at the local level in support of emergency response, radiological protection response, evacuation, and underground rescue. The system provides data communications, data processing, managerial reports, data storage, and data analysis. This system's primary surface and subsurface operator consoles, for both supervisory and remote control activities, will be located in a Central Control Center (CCC) inside one of the surface facility buildings. The system

  20. Monitoring of Low Levels of Furfural in Power Transformer Oil with a Sensor System Based on a POF-MIP Platform

    Science.gov (United States)

    Cennamo, Nunzio; De Maria, Letizia; D’Agostino, Girolamo; Zeni, Luigi; Pesavento, Maria

    2015-01-01

    In this work an innovative, miniaturized and low cost optical chemical sensor (POF-MIP platform), based on a molecular imprinted polymer (MIP) and surface plasmon resonance in a plastic optical fiber (POF), is presented and preliminarily tested for monitoring of furfural (furan-2-carbaldehyde) in transformer oil. To this end, the optical platform was coupled to an MIP layer, highly selective for furfural. The ability of the developed sensor to directly detect furfural in the insulating oil was investigated. The detection limit of the sensor has been found to be 9 ppb, with a linear response up to about 30 ppb. However there is a sensible response up to 0.15 ppm. Because of the small linearity range, the Hill equation is suggested for the quantification. The sensor has been effectively tested in real oil samples collected from aged electrical equipment removed from service. The assessed concentration of furfural is in good agreement with that evaluated by a high pressure liquid chromatography (HLPC) method, confirming the good selectivity of the proposed sensor. PMID:25871719

  1. Monitoring of low levels of furfural in power transformer oil with a sensor system based on a POF-MIP platform.

    Science.gov (United States)

    Cennamo, Nunzio; De Maria, Letizia; D'Agostino, Girolamo; Zeni, Luigi; Pesavento, Maria

    2015-04-13

    In this work an innovative, miniaturized and low cost optical chemical sensor (POF-MIP platform), based on a molecular imprinted polymer (MIP) and surface plasmon resonance in a plastic optical fiber (POF), is presented and preliminarily tested for monitoring of furfural (furan-2-carbaldehyde) in transformer oil. To this end, the optical platform was coupled to an MIP layer, highly selective for furfural. The ability of the developed sensor to directly detect furfural in the insulating oil was investigated. The detection limit of the sensor has been found to be 9 ppb, with a linear response up to about 30 ppb. However there is a sensible response up to 0.15 ppm. Because of the small linearity range, the Hill equation is suggested for the quantification. The sensor has been effectively tested in real oil samples collected from aged electrical equipment removed from service. The assessed concentration of furfural is in good agreement with that evaluated by a high pressure liquid chromatography (HLPC) method, confirming the good selectivity of the proposed sensor.

  2. Monitoring of Low Levels of Furfural in Power Transformer Oil with a Sensor System Based on a POF-MIP Platform

    Directory of Open Access Journals (Sweden)

    Nunzio Cennamo

    2015-04-01

    Full Text Available In this work an innovative, miniaturized and low cost optical chemical sensor (POF-MIP platform, based on a molecular imprinted polymer (MIP and surface plasmon resonance in a plastic optical fiber (POF, is presented and preliminarily tested for monitoring of furfural (furan-2-carbaldehyde in transformer oil. To this end, the optical platform was coupled to an MIP layer, highly selective for furfural. The ability of the developed sensor to directly detect furfural in the insulating oil was investigated. The detection limit of the sensor has been found to be 9 ppb, with a linear response up to about 30 ppb. However there is a sensible response up to 0.15 ppm. Because of the small linearity range, the Hill equation is suggested for the quantification. The sensor has been effectively tested in real oil samples collected from aged electrical equipment removed from service. The assessed concentration of furfural is in good agreement with that evaluated by a high pressure liquid chromatography (HLPC method, confirming the good selectivity of the proposed sensor.

  3. Power Monitoring and Control for Large Scale projects: SKA, a case study

    CERN Document Server

    Barbosa, Domingos; Maia, Dalmiro; Carvalho, Bruno; Vieira, Jorge; Swart, Paul; Roux, Gerhard Le; Natarajan, Swaminathan; van Ardenne, Arnold; Seca, Luis

    2016-01-01

    Large sensor-based science infrastructures for radio astronomy like the SKA will be among the most intensive data-driven projects in the world, facing very high demanding computation, storage, management, and above all power demands. The geographically wide distribution of the SKA and and its associated processing requirements in the form of tailored High Performance Computing (HPC) facilities, require a Greener approach towards the Information and Communications Technologies (ICT) adopted for the data processing to enable operational compliance to potentially strict power budgets. Addressing the reduction of electricity costs, improve system power monitoring and the generation and management of electricity at system level is paramount to avoid future inefficiencies and higher costs and enable fulfillments of Key Science Cases. Here we outline major characteristics and innovation approaches to address power efficiency and long-term power sustainability for radio astronomy projects, focusing on Green ICT for s...

  4. Computer Jet-Engine-Monitoring System

    Science.gov (United States)

    Disbrow, James D.; Duke, Eugene L.; Ray, Ronald J.

    1992-01-01

    "Intelligent Computer Assistant for Engine Monitoring" (ICAEM), computer-based monitoring system intended to distill and display data on conditions of operation of two turbofan engines of F-18, is in preliminary state of development. System reduces burden on propulsion engineer by providing single display of summary information on statuses of engines and alerting engineer to anomalous conditions. Effective use of prior engine-monitoring system requires continuous attention to multiple displays.

  5. Computer Jet-Engine-Monitoring System

    Science.gov (United States)

    Disbrow, James D.; Duke, Eugene L.; Ray, Ronald J.

    1992-01-01

    "Intelligent Computer Assistant for Engine Monitoring" (ICAEM), computer-based monitoring system intended to distill and display data on conditions of operation of two turbofan engines of F-18, is in preliminary state of development. System reduces burden on propulsion engineer by providing single display of summary information on statuses of engines and alerting engineer to anomalous conditions. Effective use of prior engine-monitoring system requires continuous attention to multiple displays.

  6. Sistema de Adquisición y Almacenamiento de Datos para Monitorización del Estado de Transformadores de Potencia Data Acquisition and Storage System for Condition Monitoring. Application to Operating Power Transformers

    Directory of Open Access Journals (Sweden)

    P. Mariño

    2004-01-01

    Full Text Available El objetivo del presente trabajo es el diseño y realización de un sistema de adquisición, procesado y almacenamiento de datos para la monitorización del estado de transformadores de potencia. Utilizando técnicas de Almacén de Datos (Data Warehouse e instrumentos virtuales, se creó un sistema de medida en cuatro transformadores en funcionamiento de 40 MVA. Se ha proporcionado a la aplicación que maneja los modelos de predicción, abstracciones de los sensores que los autores han denominado Tarjetas de Adquisición Virtuales. El sistema desarrollado en este trabajo tiene la ventaja frente a los sistemas comerciales existentes de ser fácilmente reconfigurable. Los subsistemas desarrollados, se pueden modificar para adaptarse a la monitorización del estado de otros equipos que necesiten medir variables mediante sensoresThe objective of the current work is the design and development of an acquisition, processing and storage data system for monitoring the condition of power transformers. Using techniques for data storage (Data Warehouse and virtual instruments, a measuring system was created in four 40 MVA transformers. The application that handles the prediction models was provided with an abstraction of the sensors, which the authors have named Virtual Acquisition Cards. Compared with available commercial software the acquisition system developed in this work has the advantage of being easily reconfigurable. The subsystems designed can be easily modified to monitor the estate of any other equipment that needs to measure variables using sensors

  7. Power Plant Emission Monitoring in Munich Using Differential Column Measurements

    Science.gov (United States)

    Chen, Jia; Nguyen, Hai; Toja-Silva, Francisco; Heinle, Ludwig; Hase, Frank; Butz, André

    2017-04-01

    Differential column measurements using compact Fourier transform spectrometers (EM27/SUN) have shown to be an effective method to determine the greenhouse gas emissions. Citywide measurement campaigns were carried out in Boston, Indianapolis, San Francisco, etc., focusing on city (e.g. emissions from natural gas infrastructure) and local sources. We are particularly working on validating this novel method for attributing and quantifying local emission sources. Optimal strategies are developed for measuring in different seasons with various sun elevations. We have deployed two spectrometers to monitor the CO2 and CH4 emission rates (kg s-1) of a natural gas fired combined heat-and-power plant in Munich, Germany (Heizkraftwerk Süd). We placed our spectrometers in the vicinity (differential column measurements for determining power plant emissions and explore their sensitivities to meteorological and model parameters. In addition, we present measurement strategies and experimental design criteria for different meteorological conditions and time of the year, including winter when the sun elevation is low and the column inclination becomes very important. Differential column measurements using compact spectrometers are shown to be a reliable method to monitor power plant emissions.

  8. Impact of grounding and filtering on power insulation monitoring in insulated terrestrial power networks

    NARCIS (Netherlands)

    van Vugt, Pieter Karel Anton; Bijman, Rob; Timens, R.B.; Leferink, Frank Bernardus Johannes

    2013-01-01

    Insulated terrestrial power networks are used for reliable systems such as large production plants, hospital operating rooms and naval ships. The system is isolated from ground and a first fault, such as a short circuit between a phase and ground, will not result in disconnection of the power via

  9. Digital Solution to Mining Image Monitor System

    Institute of Scientific and Technical Information of China (English)

    刘越男; 孙继平; 苏辉; 那景芳

    2001-01-01

    The thesis describes an advanced digital solution to mining digital image monitor system, which makes up the shortage of the traditional mining analog image monitor. It illustrates the system components and how to choose the encoder bandwidth of the system. The problem of image multicast and its solution in LAN are also discussed.

  10. Software For Monitoring VAX Computer Systems

    Science.gov (United States)

    Farkas, Les; Don, Ken; Lavery, David; Baron, Amy

    1994-01-01

    VAX Continuous Monitoring System (VAXCMS) computer program developed at NASA Headquarters to aid system managers in monitoring performances of VAX computer systems through generation of graphic images summarizing trends in performance metrics over time. VAXCMS written in DCL and VAX FORTRAN for use with DEC VAX-series computers running VMS 5.1 or later.

  11. A low-power multi-modal body sensor network with application to epileptic seizure monitoring.

    Science.gov (United States)

    Altini, Marco; Del Din, Silvia; Patel, Shyamal; Schachter, Steven; Penders, Julien; Bonato, Paolo

    2011-01-01

    Monitoring patients' physiological signals during their daily activities in the home environment is one of the challenge of the health care. New ultra-low-power wireless technologies could help to achieve this goal. In this paper we present a low-power, multi-modal, wearable sensor platform for the simultaneous recording of activity and physiological data. First we provide a description of the wearable sensor platform, and its characteristics with respect to power consumption. Second we present the preliminary results of the comparison between our sensors and a reference system, on healthy subjects, to test the reliability of the detected physiological (electrocardiogram and respiration) and electromyography signals.

  12. Power quality in power systems and electrical machines

    CERN Document Server

    Fuchs, Ewald

    2015-01-01

    The second edition of this must-have reference covers power quality issues in four parts, including new discussions related to renewable energy systems. The first part of the book provides background on causes, effects, standards, and measurements of power quality and harmonics. Once the basics are established the authors move on to harmonic modeling of power systems, including components and apparatus (electric machines). The final part of the book is devoted to power quality mitigation approaches and devices, and the fourth part extends the analysis to power quality solutions for renewable

  13. Advanced Systems for Monitoring Underwater Sounds

    Science.gov (United States)

    Lane, Michael; Van Meter, Steven; Gilmore, Richard Grant; Sommer, Keith

    2007-01-01

    The term "Passive Acoustic Monitoring System" (PAMS) describes a developmental sensing-and-data-acquisition system for recording underwater sounds. The sounds (more precisely, digitized and preprocessed versions from acoustic transducers) are subsequently analyzed by a combination of data processing and interpretation to identify and/or, in some cases, to locate the sources of those sounds. PAMS was originally designed to locate the sources such as fish of species that one knows or seeks to identify. The PAMS unit could also be used to locate other sources, for example, marine life, human divers, and/or vessels. The underlying principles of passive acoustic sensing and analyzing acoustic-signal data in conjunction with temperature and salinity data are not new and not unique to PAMS. Part of the uniqueness of the PAMS design is that it is the first deep-sea instrumentation design to provide a capability for studying soniferous marine animals (especially fish) over the wide depth range described below. The uniqueness of PAMS also lies partly in a synergistic combination of advanced sensing, packaging, and data-processing design features with features adapted from proven marine instrumentation systems. This combination affords a versatility that enables adaptation to a variety of undersea missions using a variety of sensors. The interpretation of acoustic data can include visual inspection of power-spectrum plots for identification of spectral signatures of known biological species or artificial sources. Alternatively or in addition, data analysis could include determination of relative times of arrival of signals at different acoustic sensors arrayed at known locations. From these times of arrival, locations of acoustic sources (and errors in those locations) can be estimated. Estimates of relative locations of sources and sensors can be refined through analysis of the attenuation of sound in the intervening water in combination with water-temperature and salinity

  14. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2005-04-27

    The objective of this program is to develop a system to both monitor the vibration of a bottomhole assembly, and to adjust the properties of an active damper in response to these measured vibrations. Phase I of this program, which entailed modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype, was completed on May 31, 2004. The principal objectives of Phase II are: more extensive laboratory testing, including the evaluation of different feedback algorithms for control of the damper; design and manufacture of a field prototype system; and, testing of the field prototype in drilling laboratories and test wells. As a result of the lower than expected performance of the MR damper noted last quarter, several additional tests were conducted. These dealt with possible causes of the lack of dynamic range observed in the testing: additional damping from the oil in the Belleville springs; changes in properties of the MR fluid; and, residual magnetization of the valve components. Of these, only the last was found to be significant. By using a laboratory demagnetization apparatus between runs, a dynamic range of 10:1 was achieved for the damper, more than adequate to produce the needed improvements in drilling. Additional modeling was also performed to identify a method of increasing the magnetic field in the damper. As a result of the above, several changes were made in the design. Additional circuitry was added to demagnetize the valve as the field is lowered. The valve was located to above the Belleville springs to reduce the load placed upon it and offer a greater range of materials for its construction. In addition, to further increase the field strength, the coils were relocated from the mandrel to the outer housing. At the end of the quarter, the redesign was complete and new parts were on order. The project is approximately three months behind schedule at this time.

  15. Design and Development of Patient Monitoring System

    Science.gov (United States)

    Hazwanie Azizulkarim, Azra; Jamil, Muhammad Mahadi Abdul; Ambar, Radzi

    2017-08-01

    Patient monitoring system allows continuous monitoring of patient vital signs, support decision making among medical personnel and help enhance patient care. This system can consist of devices that measure, display and record human’s vital signs, including body temperature, heart rate, blood pressure and other health-related criteria. This paper proposes a system to monitor the patient’s conditions by monitoring the body temperature and pulse rate. The system consists of a pulse rate monitoring software and a wearable device that can measure a subject’s temperature and pulse rate only by using a fingertip. The device is able to record the measurement data and interface to PC via Arduino microcontroller. The recorded data can be viewed as a historical file or can be archived for further analysis. This work also describes the preliminary experimental results of the selected sensors to show the usefulness of the sensors for the proposed patient monitoring system.

  16. Knolls Atomic Power Laboratory environmental monitoring report, calendar year 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    The results of the effluent and environmental monitoring programs at the three Knolls Atomic Power Laboratory (KAPL) sites are summarized and assessed in this report. The principal function at KAPL sites (Knolls, Kesselring, and Windsor) is research and development in the design and operation of Naval nuclear propulsion plants. The Kesselring Site is also used for the training of personnel in the operation of these plants. The Naval nuclear propulsion plant at the Windsor Site is currently being dismantled. Operations at the three KAPL sites resulted in no significant release of hazardous substances or radioactivity to the environment. The effluent and environmental monitoring programs conducted by KAPL are designed to determine the effectiveness of treatment and control methods, to provide measurement of the concentrations in effluents for comparison with applicable standards, and to assess resultant concentrations in the environment. The monitoring programs include analyses of samples of liquid and gaseous effluents for chemical constituents and radioactivity as well as monitoring of environmental air, water, sediment, and fish. Radiation measurements are also made around the perimeter of each site and at off-site background locations.

  17. Monitoring by holographic radar systems

    Science.gov (United States)

    Catapano, Ilaria; Crocco, Lorenzo; Affinito, Antonio; Gennarelli, Gianluca; Soldovieri, Francesco

    2013-04-01

    Nowadays, radar technology represents a significant opportunity to collect useful information for the monitoring and conservation of critical infrastructures. Radar systems exploit the non-invasive interaction between the matter and the electromagnetic waves at microwave frequencies. Such an interaction allows obtaining images of the region under test from which one can infer the presence of potential anomalies such as deformations, cracks, water infiltrations, etc. This information turns out to be of primary importance in practical scenarios where the probed structure is in a poor state of preservation and renovation works must be planned. In this framework, the aim of this contribution is to describe the potentialities of the holographic radar Rascan 4/4000, a holographic radar developed by Remote Sensing Laboratory of Bauman Moscow State Technical University, as a non-destructive diagnostic tool capable to provide, in real-time, high resolution subsurface images of the sounded structure [1]. This radar provides holograms of hidden anomalies from the amplitude of the interference signal arising between the backscattered signal and a reference signal. The performance of the holographic radar is appraised by means of several experiments. Preliminary tests concerning the imaging below the floor and inside wood structures are carried out in controlled conditions at the Electromagnetic Diagnostic Laboratory of IREA-CNR. After, with reference to bridge monitoring for security aim, the results of a measurement campaign performed on the Musmeci bridge are presented [2]. Acknowledgments This research has been performed in the framework of the "Active and Passive Microwaves for Security and Subsurface imaging (AMISS)" EU 7th Framework Marie Curie Actions IRSES project (PIRSES-GA-2010-269157). REFERENCES [1] S. Ivashov, V. Razevig, I. Vasilyev, A. Zhuravlev, T. Bechtel, L. Capineri, The holographic principle in subsurface radar technology, International Symposium to

  18. Small fission power systems for Mars

    Science.gov (United States)

    Lipinski, Ronald J.; Wright, Steven A.; Sherman, Martin P.; Lenard, Roger X.; Talandis, Regina A.; Poston, David I.; Kapernick, Richard; Guffee, Ray; Reid, Robert; Elson, Jay; Lee, James

    2002-01-01

    A Mars surface power system configuration with an output power of 3 kWe and a system mass of 775 kg is described. It consists of a heatpipe-cooled reactor with UN fuel coupled to a Stirling engine with a fixed conical radiator driven by loop heat pipes. Key to achieving this low mass is the use of a highly radiation-resistant multiplexer for monitoring and controlling the reactor, as well as radiation resistant generators and motors. Also key is the judicious placement of shields to prevent radiation scattered from the Martian surface and air from damaging the reactor controls. Several alternate configurations also are briefly looked at, including a moderated reactor with UZrH fuel and a reactor using 233U instead of 235U. The moderated reactor system has essentially the same mass as the baseline unmoderated UN system and yields the same radiation shielding requirements. The 233U reactor is significantly smaller and yields a system mass about 228 kg lighter than with 235U, but part of this weight reduction is due to the use of removable neutron absorbers to assure subcriticality with water immersion, as opposed to permanently placed absorbers. .

  19. The International Remote Monitoring Project -- First results of the Argentina nuclear power station field trial

    Energy Technology Data Exchange (ETDEWEB)

    Bonino, A.; Pizarro, L.; Perez, A. [Ente Nacional Regulador Nuclear, Buenos Aires (Argentina); Schoeneman, J.L.; Dupree, S.A.; Martinez, R.L. [Sandia National Labs., Albuquerque, NM (United States); Maxey, C. [Oak Ridge National Lab., TN (United States)

    1995-12-31

    As part of the International Remote Monitoring Project field trials, during the month of March, 1995 a Remote Monitoring System (RMS) was installed at the Embalse Nuclear Power Station in Embalse, Argentina. This system monitors the status of four typical Candu spent fuel dry storage silos. The monitoring equipment for each silo consists of analog temperature and gamma radiation sensors and digital motion and electronic fiber-optic seals connected to a wireless Authenticate Item Monitoring System (AIMS). All sensor data are authenticated and transmitted via RF link to Receiver Processor Units (RPU) coupled to Remote Monitoring System equipment located in a nearby IAEA/ENREN inspector office. One of these RPUs is connected to Remote Monitoring equipment capable of information transmission (via commercial telephone links) to Data Review Stations (DRS) at ENREN laboratories in Buenos Aires, Argentina, and at Sandia National Laboratories, Albuquerque, New Mexico. The other RPU is used for on-site data storage and analysis. It is anticipated that this information will soon be transmitted to a DRS at the ABACC facility in Rio de Janeiro, Brazil. During these trials site data will be collected and analyzed periodically from Buenos Aires, Albuquerque, and Rio de Janeiro. Installation detail and data analysis will be presented in this paper.

  20. Wireless and Powerless Sensing Node System Developed for Monitoring Motors

    Directory of Open Access Journals (Sweden)

    Dasheng Lee

    2008-08-01

    Full Text Available Reliability and maintainability of tooling systems can be improved through condition monitoring of motors. However, it is difficult to deploy sensor nodes due to the harsh environment of industrial plants. Sensor cables are easily damaged, which renders the monitoring system deployed to assure the machine’s reliability itself unreliable. A wireless and powerless sensing node integrated with a MEMS (Micro Electro-Mechanical System sensor, a signal processor, a communication module, and a self-powered generator was developed in this study for implementation of an easily mounted network sensor for monitoring motors. A specially designed communication module transmits a sequence of electromagnetic (EM pulses in response to the sensor signals. The EM pulses can penetrate through the machine’s metal case and delivers signals from the sensor inside the motor to the external data acquisition center. By using induction power, which is generated by the motor’s shaft rotation, the sensor node is self-sustaining; therefore, no power line is required. A monitoring system, equipped with novel sensing nodes, was constructed to test its performance. The test results illustrate that, the novel sensing node developed in this study can effectively enhance the reliability of the motor monitoring system and it is expected to be a valuable technology, which will be available to the plant for implementation in a reliable motor management program.