Investigation of the oxidative ammonolysis of propylene on oxide catalysts containing molybdenum and using the response method

International Nuclear Information System (INIS)

Gadzhiev, K.N.; Adzhamov, K.Y.; Alkhazov, T.G.; Khanmamedova, A.K.

1985-01-01

The response method has been used to study the oxidative ammonolysis of propylene on MoO 3 and molybdenum oxide systems containing bismuth, silicon, and phosphorous ions. The response curves obtained for ammonia, propylene, CO 2 , acrolein, acrylonitrile in these systems are discussed and compared with individual molybdenum trioxide. It has been shown that the modifying action of ammonia on the catalyst surfaces determines the direction of the oxidative conversion of the propylene

Investigation of optical properties and electronic transitions in bulk and nano-microribbons of molybdenum trioxide

International Nuclear Information System (INIS)

Lupan, O; Mishra, Y K; Adelung, R; Trofim, V; Cretu, V; Stamov, I; Syrbu, N N; Tiginyanu, I

2014-01-01

In this work, we report on crystalline quality and optical characteristics of molybdenum trioxide (MoO 3 ) bulk and nano-microribbons grown by rapid thermal oxidation (RTO). The developed RTO procedure allows one to synthesize highly crystalline (α-phase) bulk and nano-microribbons of MoO 3 . For R–Γ indirect transitions in bulk single crystals of MoO 3 , it has been found that the width of the bandgap along the E‖c polarization, associated with transitions R v1 –Γ c1 , is lower than the width of the band gap in polarization E ⊥ c, associated with transitions R v2 –Γ c2 . This result is indicative of splitting of the absorption edge due to α-MoO 3 structural anisotropy. Studies of the polarization dependence of the absorption in nano-microribbons (d ≈ 15–500 nm) demonstrated that the energy gap corresponding to R v1 –X c1 (E‖c) transition is smaller than that of R v2 –X c2 (E ⊥ c) transition. Similar dependence has been found for the R–Y indirect transitions. The results of the investigation of the reflectance spectra in the energy range from 3 to 6 eV are shown. By using the Kramers–Kronig method, the optical functions were derived from the reflection spectra of nano-microribbons, and the polarization dependence of direct energy transitions at the point R in the Brillouin zone are determined. The alternation in splitting caused by polarization of the absorption edge related to indirect transitions due to polarization opens new prospects for the design and fabricating interesting optoelectronic devices based on α-MoO 3 bulk and nano-microribbons with characteristics dependent on the polarization of light waves. (paper)

A kinetic study of the redox reactions of complex cyanides of iron, molybdenum and tungsten with compounds of the group VI A elements

International Nuclear Information System (INIS)

Dennis, C.R.

1981-01-01

The kinetic study arises out of the fact that few is known about redox kinetics of complex cyanides of molybdenum and tungsten. The redox kinetics of the complex cyanides of iron with organic and inorganic compounds are well known in organic chemistry. This comparitive study is done to obtain more information on redox reactions of complex cyanides of molybdenum and tungsten considering its greater applicability in organic and inorganic chemistry because of the propitious reduction potential of this complex cyanide in acidic and alkaline mediums. Various redox systems are kinetically investigated regarding the influence of the oxidising agent, reducing agent hydrogen ions and alkaline-metal ions on the reaction rate. A reaction mechanism is proposed for every system

Recovery of molybdenum using alumina microspheres and precipitation with selective organic reagents

International Nuclear Information System (INIS)

Carvalho, Fatima Maria Sequeira de; Abrao, Alcidio

1998-01-01

In this paper is presented a study for the optimization of dissolution of the UAL x plates used for irradiation and production of radiomolybdenum. The alloy is dissolved in nitric acid with mercury as catalyst. The separation and concentration of the molybdenum was achieved using a chromatographic grade alumina microspheres column. the purified eluted molybdenum is finally precipitated using one of the selective reagents: alizarine blue, α,α'- bipyridine and 1,10-phenanthroline. Any one of the obtained precipitate can be fired to the molybdenum trioxide. The interference of the following elements was studied: Re(VII), U(VI), Cr(VI), W(VI), V(V), Te(IV), Ti(IV), Zr(IV), Th(IV), Fe(III), Au(III), Ru(III), Al(III), Bi(III), Sb(III), Ce(IV), Pr(III), Sc(III), Y(III), Sm(III), Ba(II), Sr(II), Ni(II), Co(II), Cs(I). The molybdenum precipitates were characterized by gravimetric, CHN, TG, DTG, IR and X-ray diffraction analyses. (author)

Kinetic parameters of nitridation of molybdenum and niobium alloys with various structure states

International Nuclear Information System (INIS)

Solodkin, G.A.; Bulgach, A.A.; Likhacheva, T.E.

1985-01-01

Effect of preliminary plastic strain under rolling on kinetic parameters of nitridation of VN-2AEh, VN-3 niobium alloys and molybdenum alloy with hafnium is investigated. Extreme character of dependence of kinetic parameters of nitridation on the degree of reduction under rolling is determined. Preliminary plastic strain at negligible reduction is shown to accelerate growth of the zone of internal nitridation and decelerates growth of the nitride zone. Nitrogen atom removal from the surface to the centre is retarded at the increase of the degree of reduction up to 50% and higher. The degree of deformations is the higher the lower nitridation temperature is

Direct atomic-emission determination of tungsten in molybdenum oxide in dc arc

International Nuclear Information System (INIS)

Zolotareva, N.I.; Grazhulene, S.S.

2007-01-01

A method of direct atomic-emission determination of tungsten impurity in molybdenum trioxide of high purity in dc arc is presented. Chemically active additives of elementary sulfur and gallium oxide are used to optimize W evaporation rate and residence time in the arc plasma. The procedure is easy to use and provides the limit of W determination at a level of 2x10 -4 wt. % [ru

Environmental Benign Process for Production of Molybdenum Metal from Sulphide Based Minerals

Science.gov (United States)

Rajput, Priyanka; Janakiram, Vangada; Jayasankar, Kalidoss; Angadi, Shivakumar; Bhoi, Bhagyadhar; Mukherjee, Partha Sarathi

2017-10-01

Molybdenum is a strategic and high temperature refractory metal which is not found in nature in free state, it is predominantly found in earth's crust in the form of MoO3/MoS2. The main disadvantage of the industrial treatment of Mo concentrate is that the process contains many stages and requires very high temperature. Almost in every step many gaseous, liquid, solid chemical substances are formed which require further treatment. To overcome the above drawback, a new alternative one step novel process is developed for the treatment of sulphide and trioxide molybdenum concentrates. This paper presents the results of the investigations on molybdenite dissociation (MoS2) using microwave assisted plasma unit as well as transferred arc thermal plasma torch. It is a single step process for the preparation of pure molybdenum metal from MoS2 by hydrogen reduction in thermal plasma. Process variable such as H2 gas, Ar gas, input current, voltage and time have been examined to prepare molybdenum metal. Molybdenum recovery of the order of 95% was achieved. The XRD results confirm the phases of molybdenum metal and the chemical analysis of the end product indicate the formation of metallic molybdenum (Mo 98%).

Kinetics of molybdenum reduction to molybdenum blue by Bacillus sp. strain A.rzi.

Science.gov (United States)

Othman, A R; Bakar, N A; Halmi, M I E; Johari, W L W; Ahmad, S A; Jirangon, H; Syed, M A; Shukor, M Y

2013-01-01

Molybdenum is very toxic to agricultural animals. Mo-reducing bacterium can be used to immobilize soluble molybdenum to insoluble forms, reducing its toxicity in the process. In this work the isolation of a novel molybdate-reducing Gram positive bacterium tentatively identified as Bacillus sp. strain A.rzi from a metal-contaminated soil is reported. The cellular reduction of molybdate to molybdenum blue occurred optimally at 4 mM phosphate, using 1% (w/v) glucose, 50 mM molybdate, between 28 and 30 °C and at pH 7.3. The spectrum of the Mo-blue product showed a maximum peak at 865 nm and a shoulder at 700 nm. Inhibitors of bacterial electron transport system (ETS) such as rotenone, sodium azide, antimycin A, and potassium cyanide could not inhibit the molybdenum-reducing activity. At 0.1 mM, mercury, copper, cadmium, arsenic, lead, chromium, cobalt, and zinc showed strong inhibition on molybdate reduction by crude enzyme. The best model that fitted the experimental data well was Luong followed by Haldane and Monod. The calculated value for Luong's constants p max, K(s), S(m), and n was 5.88 μmole Mo-blue hr(-1), 70.36 mM, 108.22 mM, and 0.74, respectively. The characteristics of this bacterium make it an ideal tool for bioremediation of molybdenum pollution.

Kinetics of Molybdenum Reduction to Molybdenum Blue by Bacillus sp. Strain A.rzi

Directory of Open Access Journals (Sweden)

A. R. Othman

2013-01-01

Full Text Available Molybdenum is very toxic to agricultural animals. Mo-reducing bacterium can be used to immobilize soluble molybdenum to insoluble forms, reducing its toxicity in the process. In this work the isolation of a novel molybdate-reducing Gram positive bacterium tentatively identified as Bacillus sp. strain A.rzi from a metal-contaminated soil is reported. The cellular reduction of molybdate to molybdenum blue occurred optimally at 4 mM phosphate, using 1% (w/v glucose, 50 mM molybdate, between 28 and 30°C and at pH 7.3. The spectrum of the Mo-blue product showed a maximum peak at 865 nm and a shoulder at 700 nm. Inhibitors of bacterial electron transport system (ETS such as rotenone, sodium azide, antimycin A, and potassium cyanide could not inhibit the molybdenum-reducing activity. At 0.1 mM, mercury, copper, cadmium, arsenic, lead, chromium, cobalt, and zinc showed strong inhibition on molybdate reduction by crude enzyme. The best model that fitted the experimental data well was Luong followed by Haldane and Monod. The calculated value for Luong’s constants pmax, Ks, Sm, and n was 5.88 μmole Mo-blue hr−1, 70.36 mM, 108.22 mM, and 0.74, respectively. The characteristics of this bacterium make it an ideal tool for bioremediation of molybdenum pollution.

Kinetics of molybdenum(6) complexation with o,o'-dihydroxyazo compounds or heterocyclic azo compounds in the presence of hydroxylamine

International Nuclear Information System (INIS)

Kochelaeva, G.A.; Degtyarev, M.Yu.; Ivanov, V.M.; Prokhorova, G.V.; Figurovskaya, V.N.

1999-01-01

The kinetics of complexation in the system molybdenum(6)-azo compound-hydroxylamine was studied. Azo compounds of the types o,o'-dihydroxyazo compounds, such as Lyumogallion IREA and Magneson IREA, and heterocyclic azo compounds, such as 4-(2-pyridylazo)resorcinol and 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol, were studied. The formation of mixed-ligand complexes with the ratio of component 1 : 1 : 1 was detected. Rate constants, activation energies, and stability constants of the forming compounds were evaluated. It was concluded that the reagents under study are promising for the analytical chemistry of molybdenum [ru

Study of the oxidation kinetics of the nickel-molybdenum alloy

International Nuclear Information System (INIS)

Gouillon, Marie-Josephe

1974-01-01

This research thesis reports the study of the oxidation of a nickel-molybdenum alloy in the high-nickel-content part of this alloy. After a bibliographical study on the both metals, the author proposes a physical model based on observed phenomena and based on experimental results. Based on a thermodynamic study, the author compares the stability of the different oxides which may be formed, and reports a prediction of oxides obtained on the alloy during oxidation. Qualitative and quantitative studies have been performed by scanning electron microscopy coupled with electronic microprobe analysis to investigate morphological characteristics on oxidation films. A kinetic study by thermogravimetry shows a decrease of the alloy oxidation rate with respect to that of pure nickel at temperatures lower than 800 degrees C. This result is interpreted by the intervention of two opposed diffusion phenomena which act against each other [fr

Antimicrobial, antioxidant and cytotoxic effect of Molybdenum trioxide nanoparticles and application of this for degradation of ketamine under different light illumination.

Science.gov (United States)

Fakhri, Ali; Nejad, Pedram Afshar

2016-06-01

A hydrothermal method was employed to synthesize Molybdenum trioxide (MoO3) nanoparticles. The synthesized samples were evaluated for photocatalytic properties and biological application. The nanoparticles characterized by scanning electron microscopy, powder X-ray diffraction, transmission electron microscopy, an energy dispersive X-ray spectrometer and UV-Vis DRS spectra. The synthesized MoO3 NPs were found to be spherical in shape with size in the range of 75nm. The synthesized MoO3 nanoparticles have good optical properties with 2.78eV of band-gap. The photocatalytic properties of the synthesized MoO3 nanoparticles were carried out by performing the degradation of ketamine under visible, UV and sunlight irradiations. A high efficiency was observed between sunlight and MoO3 nanoparticles for the photocatalysis reaction. Two compounds as intermediates of photo-degradation of ketamine under visible and UV lights were detected. The antifungal activity of the nanoscale MoO3 against Candida albicans and Aspergillus niger was assessed using the disc-diffusion susceptibility tests. All MoO3 nanoparticles concentrations showed good ABT radical scavenging activity. Then, this research has been presented to exhibit the synthesized MoO3 NPs which indicated a high antibacterial activity against Gram negative and positive bacteria and were also proved to exhibit excellent cytotoxic influence on lung and breast cancer cell lines. The results show that the high applicability of MoO3 nanoparticles biologically was great and is environmentally friendly. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of the substrate temperature on the physical properties of molybdenum tri-oxide thin films obtained through the spray pyrolysis technique

International Nuclear Information System (INIS)

Martínez, H.M.; Torres, J.; López Carreño, L.D.; Rodríguez-García, M.E.

2013-01-01

Polycrystalline molybdenum tri-oxide thin films were prepared using the spray pyrolysis technique; a 0.1 M solution of ammonium molybdate tetra-hydrated was used as a precursor. The samples were prepared on Corning glass substrates maintained at temperatures ranging between 423 and 673 K. The samples were characterized through micro Raman, X-ray diffraction, optical transmittance and DC electrical conductivity. The species MoO 3 (H 2 O) 2 was found in the sample prepared at a substrate temperature of 423 K. As the substrate temperature rises, the water disappears and the samples crystallize into α-MoO 3 . The optical gap diminishes as the substrate temperature rises. Two electrical transport mechanisms were found: hopping under 200 K and intrinsic conduction over 200 K. The MoO 3 films' sensitivity was analyzed for CO and H 2 O in the temperature range 160 to 360 K; the results indicate that CO and H 2 O have a reduction character. In all cases, it was found that the sensitivity to CO is lower than that to H 2 O. - Highlights: ► A low cost technique is used which produces good material. ► Thin films are prepared using ammonium molybdate tetra hydrated. ► The control of the physical properties of the samples could be done. ► A calculation method is proposed to determine the material optical properties. ► The MoO 3 thin films prepared by spray pyrolysis could be used as gas sensor.

Electronic structure evolution in doping of fullerene (C{sub 60}) by ultra-thin layer molybdenum trioxide

Energy Technology Data Exchange (ETDEWEB)

Wang, Chenggong; Wang, Congcong; Kauppi, John [Department of Physics and Astronomy, University of Rochester, Rochester, New York 14627 (United States); Liu, Xiaoliang [Institute for Super-microstructure and Ultrafast Process in Advanced Materials (ISUPAM), Central South University, Changsha, Hunan 410083 (China); Gao, Yongli, E-mail: ygao@pas.rochester.edu [Department of Physics and Astronomy, University of Rochester, Rochester, New York 14627 (United States); Institute for Super-microstructure and Ultrafast Process in Advanced Materials (ISUPAM), Central South University, Changsha, Hunan 410083 (China)

2015-08-28

Ultra-thin layer molybdenum oxide doping of fullerene has been investigated using ultraviolet photoemission spectroscopy (UPS) and X-ray photoemission spectroscopy (XPS). The highest occupied molecular orbital (HOMO) can be observed directly with UPS. It is observed that the Fermi level position in fullerene is modified by ultra-thin-layer molybdenum oxide doping, and the HOMO onset is shifted to less than 1.3 eV below the Fermi level. The XPS results indicate that charge transfer was observed from the C{sub 60} to MoO{sub x} and Mo{sup 6+} oxides is the basis as hole dopants.

Performance of the periodic pulse technique--4. Periodic pulse reaction kinetics of oxidative dehydrogenation of isobutyraldehyde

Energy Technology Data Exchange (ETDEWEB)

Hattori, T.; Ii, M.; Murakami, Y.

1980-07-01

The periodic pulse method was used to study the reaction mechanism and kinetics of the oxidative dehydrogenation of isobutyraldehyde (IBA) by following the formation rates of methacrolein (MA), carbon monoxide and dioxide (CO/sub x/), and other products (P) as a function of pulse widths and reactant partial pressures at 350/sup 0/C over a 2:3 antimony oxide/molybdenum trioxide catalyst. The results were consistent with a mechanism according to which IBA reacts with oxygen retained by the catalyst to form MA, causing reduction of the catalyst. The IBA also adsorbed on the surface as an oxygenated species which either reacted with gas-phase oxygen to form CO/sub x/ or desorbed as an oxygenated P. The reduced catalyst surface was reoxidized by oxygen adsorption. Implications of catalyst tailoring for increased MA yields by improving the redox mechanism and inhibiting the surface reactions, are discussed.

Enhanced generation of hydroxyl radicals on well-crystallized molybdenum trioxide/nano-graphite anode with sesame cake-like structure for degradation of bio-refractory antibiotic.

Science.gov (United States)

Tang, Bo; Du, Jiannan; Feng, Qingmao; Zhang, Jiaqi; Wu, Dan; Jiang, Xiankai; Dai, Ying; Zou, Jinlong

2018-05-01

Anodic electro-catalysis oxidation is a highly effective way to solve the pollution problem of antibiotics in wastewater and receiving water bodies. In this study, for the first time, molybdenum trioxide/Nano-graphite (MoO 3 /Nano-G) composites are synthesized as anodic catalysts by a surfactant-assisted solvothermal method followed by low-temperature calcination. The effects of the proportion of MoO 3 to Nano-G (10, 30 and 50%) on the properties of composites are investigated through structural characterizations and electrochemical measurements. Results indicate that MoO 3 (30)/Nano-G electrode displays the electro-catalysis degradation efficiency of 99.9% towards ceftazidime, which is much higher than those of Nano-G (46.7%) and dimensionally stable anode (69.2%). The degradation mechanism for ceftazidime is studied by investigating the yields and kinds of active species. Results show that all of the OH, O 2- and H 2 O 2 are responsible for the electro-catalytic degradation process, and the produced OH radicals are the major active species for ceftazidime degradation. The synergistic effects between MoO 3 and Nano-G greatly contribute to the activation of H 2 O molecules to produce OH, meanwhile the special sesame cake-like structure facilitates to the exposure of contaminants to OH on active sites to enhance the degradation efficiency. These results suggest that MoO 3 /Nano-G electrodes can be considered as the promising catalysts for treating bio-refractory organic wastewater. Copyright © 2018 Elsevier Inc. All rights reserved.

Contribution to the study of sulfur trioxide formation and determination of the sulfuric acid dew point in boiler plants

Energy Technology Data Exchange (ETDEWEB)

Mueller, H.

1983-11-01

This paper analyzes chemical reaction kinetics of the formation of sulfur trioxide and sulfuric acid in combustion air and flue gas of steam generators. Formulae for sulfuric acid equilibrium reactions according to Wahnschaffe (W. Grimm, 1972) and R. Hasse, H.W. Borgmann (1962) are presented. Theoretical acid dew point, combustion parameters with influence on the dew point temperature and formation of sulfates are further discussed. Sulfur trioxide formation at temperatures above 1,000 C as a non-equilibrium reaction is outlined as another variant of chemical reactions. A graphic evaluation is made of dew point conditions in brown coal dust fired, and heating oil fired steam generators. (11 refs.)

Arsenic trioxide sensitizes glioblastoma to a myc inhibitor.

Directory of Open Access Journals (Sweden)

Yayoi Yoshimura

Full Text Available Glioblastoma multiforme (GBM is associated with high mortality due to infiltrative growth and recurrence. Median survival of the patients is less than 15 months, increasing requirements for new therapies. We found that both arsenic trioxide and 10058F4, an inhibitor of Myc, induced differentiation of cancer stem-like cells (CSC of GBM and that arsenic trioxide drastically enhanced the anti-proliferative effect of 10058F4 but not apoptotic effects. EGFR-driven genetically engineered GBM mouse model showed that this cooperative effect is higher in EGFRvIII-expressing INK4a/Arf-/- neural stem cells (NSCs than in control wild type NSCs. In addition, treatment of GBM CSC xenografts with arsenic trioxide and 10058F4 resulted in significant decrease in tumor growth and increased differentiation with concomitant decrease of proneural and mesenchymal GBM CSCs in vivo. Our study was the first to evaluate arsenic trioxide and 10058F4 interaction in GBM CSC differentiation and to assess new opportunities for arsenic trioxide and 10058F4 combination as a promising approach for future differentiation therapy of GBM.

Arsenic Trioxide Injection

Science.gov (United States)

... people who have not been helped by other types of chemotherapy or whose condition has improved but then worsened following treatment with other types of chemotherapy. Arsenic trioxide is in a class of medications ...

Catalytic hydrotreatment of Illinois No. 6 coal-derived naphtha: comparison of molybdenum nitride and molybdenum sulfide for heteroatom removal

Energy Technology Data Exchange (ETDEWEB)

Raje, A.; Liaw, S.J.; Chary, K.V.R.; Davis, B.H. [University of Kentucky, Lexington, KY (United States). Center for Applied Energy Research

1995-03-16

The hydrotreatment of naphtha derived from Illinois No. 6 coal was investigated using molybdenum sulfide and nitride catalysts. The two catalysts are compared on the basis of total catalyst weight. Molybdenum sulfide is more active than molybdenum nitride for hydrodesulfurization (HDS) of a coal-derived naphtha. The rate of hydrodeoxygenation (HDO) of the naphtha over both catalysts are comparable. For hydrodenitrogenation (HDN), the sulfide is more active than the nitride only at higher temperatures ({gt}325{degree}C). Based upon conversion data, the naphtha can be lumped into a reactive and a less reactive fraction with each following first-order kinetics for heteroatom removal. The HDS and HDN rates and activation energies of the less reactive lump are smaller for the nitride than for the sulfide catalyst.

Effect of precipitation route on the properties of antimony trioxide

International Nuclear Information System (INIS)

Abdullah, Abdul Halim; Noor, Nor Hayati Mohd; Ramli, Irmawati; Hashim, Mansor

2008-01-01

Antimony trioxide was prepared, using antimony potassium tartarate as starting material, via forward and reverse precipitation technique. The characteristics of the resulting antimony oxides were determined by BET surface area method, differential thermogravimetry analysis (DTG), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR) and SEM. The DTG curves for all uncalcined samples showed only a single endothermic peak which indicated that the sample is antimony trioxide. Unlike forward precipitation technique which resulted in a single antimony trioxide phase which is senarmontite, reverse precipitation technique produced antimony trioxide with both senarmontite and valentinite phase. Upon calcinations at 723 K, a small amount of Sb 2 O 4 with cervantite phase was formed at the expense of Sb 2 O 3 senarmontite phase as detected from the XRD pattern and infrared spectrum of RSb. The effect of preparation route on the properties of the antimony trioxide produced was clearly demonstrated

Molybdenum, molybdenum oxides, and their electrochemistry.

Science.gov (United States)

Saji, Viswanathan S; Lee, Chi-Woo

2012-07-01

The electrochemical behaviors of molybdenum and its oxides, both in bulk and thin film dimensions, are critical because of their widespread applications in steels, electrocatalysts, electrochromic materials, batteries, sensors, and solar cells. An important area of current interest is electrodeposited CIGS-based solar cells where a molybdenum/glass electrode forms the back contact. Surprisingly, the basic electrochemistry of molybdenum and its oxides has not been reviewed with due attention. In this Review, we assess the scattered information. The potential and pH dependent active, passive, and transpassive behaviors of molybdenum in aqueous media are explained. The major surface oxide species observed, reversible redox transitions of the surface oxides, pseudocapacitance and catalytic reduction are discussed along with carefully conducted experimental results on a typical molybdenum glass back contact employed in CIGS-based solar cells. The applications of molybdenum oxides and the electrodeposition of molybdenum are briefly reviewed. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Biomass as biosorbent for molybdenum ions

International Nuclear Information System (INIS)

Yamaura, Mitiko; Santos, Jacinete L. dos; Damasceno, Marcos O.; Egute, Nayara dos S.; Moraes, Adeniane A.N.; Santos, Bruno Z.

2013-01-01

Biosorbents have been focused as renewable materials of low cost, and have been used for metal removal from the wastewater by adsorption phenomenon. Biosorbents are prepared of biomass, whose reactive sites in its chemical structure have affinity to bind to metal ions. In this work, performance of corn husk, sugarcane bagasse, coir, banana peel, fish scale, chitin and chitosan as biosorbents of molybdenum (VI) ions in aqueous medium was evaluated. The adsorption experiments were investigated in a batch system varying the pH solution from 0.5 to 12 and the contact time between the phases from 2 min to 70 min. 99 Mo radioisotope was used as radioactive tracer for analysis of molybdenum ions by gamma spectroscopy using a HPGe detector. Results revealed that acidity of the solution favored the adsorption of Mo (VI) ions on the all biosorbents. Adsorption values higher than 85% were found on sugarcane bagasse, coir, corn husk, chitin and chitosan at pH 2.0. Only the chitosan was dissolved at pH 0.5 and a gel was formed. The models of pseudo-second order and external film diffusion described the kinetics of adsorption of Mo ions on the coir. This work showed that the studied biomass has high potential to be used as biosorbent of molybdenum ions from acidic wastewater, and the kinetics of Mo adsorption on the coir suggested high-affinity adsorption governed by chemisorption. (author)

Biomass as biosorbent for molybdenum ions

Energy Technology Data Exchange (ETDEWEB)

Yamaura, Mitiko; Santos, Jacinete L. dos; Damasceno, Marcos O.; Egute, Nayara dos S.; Moraes, Adeniane A.N.; Santos, Bruno Z., E-mail: myamaura@ipen.br, E-mail: jlsantos@ipen.br, E-mail: molidam@ipen.br, E-mail: nayara.egute@usp.br, E-mail: adenianemrs@ig.com.br, E-mail: bzsantos@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

Biosorbents have been focused as renewable materials of low cost, and have been used for metal removal from the wastewater by adsorption phenomenon. Biosorbents are prepared of biomass, whose reactive sites in its chemical structure have affinity to bind to metal ions. In this work, performance of corn husk, sugarcane bagasse, coir, banana peel, fish scale, chitin and chitosan as biosorbents of molybdenum (VI) ions in aqueous medium was evaluated. The adsorption experiments were investigated in a batch system varying the pH solution from 0.5 to 12 and the contact time between the phases from 2 min to 70 min. {sup 99}Mo radioisotope was used as radioactive tracer for analysis of molybdenum ions by gamma spectroscopy using a HPGe detector. Results revealed that acidity of the solution favored the adsorption of Mo (VI) ions on the all biosorbents. Adsorption values higher than 85% were found on sugarcane bagasse, coir, corn husk, chitin and chitosan at pH 2.0. Only the chitosan was dissolved at pH 0.5 and a gel was formed. The models of pseudo-second order and external film diffusion described the kinetics of adsorption of Mo ions on the coir. This work showed that the studied biomass has high potential to be used as biosorbent of molybdenum ions from acidic wastewater, and the kinetics of Mo adsorption on the coir suggested high-affinity adsorption governed by chemisorption. (author)

Mineral trioxide aggregate: part 2 - a review of the material aspects.

Science.gov (United States)

Malhotra, Neeraj; Agarwal, Antara; Mala, Kundabala

2013-03-01

The purpose of this two-part series is to review the composition, properties, and products of mineral trioxide aggregate (MTA) materials. PubMed and MedLine electronic databases were used to identify scientific papers from January 1991 to May 2010. Based on the selected inclusion criteria, citations were referenced from the scientific peer-reviewed dental literature. Mineral trioxide aggregate is a refined form of the parent compound, Portland cement (PC), and demonstrates a strong biocompatibility due to the high pH level and the material's ability to form hydroxyapatite. Mineral trioxide aggregate materials provide better microleakage protection than traditional endodontic materials as observed in findings from dye-leakage, fluid-filtration, protein-leakage, and bacterial penetration-leakage studies and has been recognized as a bioactive material. Various MTA commercial products are available, including gray mineral trioxide aggregate (GMTA), white mineral trioxide aggregate (WMTA), and mineral trioxide aggregate-Angelus (AMTA). Although these materials are indicated for various dental uses and applications, long-term in-vivo clinical studies are needed. Part 1 of this article highlighted and discussed the composition and characteristics of the material. Part 2 provides an overview of commercially available MTA materials.

Kinetics of carbide formation in the molybdenum-tungsten coatings used in the ITER-like Wall

Science.gov (United States)

Maier, H.; Rasinski, M.; von Toussaint, U.; Greuner, H.; Böswirth, B.; Balden, M.; Elgeti, S.; Ruset, C.; Matthews, G. F.

2016-02-01

The kinetics of tungsten carbide formation was investigated for tungsten coatings on carbon fibre composite with a molybdenum interlayer as they are used in the ITER-like Wall in JET. The coatings were produced by combined magnetron sputtering and ion implantation. The investigation was performed by preparing focused ion beam cross sections from samples after heat treatment in argon atmosphere. Baking of the samples was done at temperatures of 1100 °C, 1200 °C, and 1350 °C for hold times between 30 min and 20 h. It was found that the data can be well described by a diffusional random walk with a thermally activated diffusion process. The activation energy was determined to be (3.34 ± 0.11) eV. Predictions for the isothermal lifetime of this coating system were computed from this information.

Development of silicide coating over molybdenum based refractory alloy and its characterization

International Nuclear Information System (INIS)

Chakraborty, S.P.; Banerjee, S.; Sharma, I.G.; Suri, A.K.

2010-01-01

Molybdenum based refractory alloys are potential candidate materials for structural applications in high temperature compact nuclear reactors and fusion reactors. However, these alloys being highly susceptible to oxidation in air or oxygen at elevated temperature, undergoes severe losses from highly volatile molybdenum trioxide species. Present investigation, therefore, examines the feasibility of development of silicide type of coating over molybdenum base TZM alloy shape (Mo > 99 wt.%) using pack cementation coating technique. TZM alloy was synthesized in this laboratory from oxide intermediates of MoO 2 , TiO 2 and ZrO 2 in presence of requisite amount of carbon, by alumino-thermic reduction smelting technique. The arc melted and homogenized samples of TZM alloy substrate was then embedded in the chosen and intimately mixed pack composition consisting of inert matrix (Al 2 O 3 ), coating powder (Si) and activator (NH 4 Cl) taken in the judicious proportion. The sealed charge packs contained in an alumina crucible were heated at temperatures of 1000 o C for 8-16 h heating cycle to develop the coating. The coating phase was confirmed to be of made of MoSi 2 by XRD analysis. The morphology of the coating was studied by SEM characterization. It had revealed that the coating was diffusion bonded where Si from coating diffused inward and Mo from TZM substrate diffused outward to form the coating. The coating was found to be resistant to oxidation when tested in air up to 1200 o C. A maximum 100 μm of coating thickness was achieved on each side of the substrate.

Development of an arsenic trioxide vapor and arsine sampling train

International Nuclear Information System (INIS)

Crecelius, E.A.; Sanders, R.W.

1980-01-01

A sampling train was evaluated using 76 As tracer for the measurement of particulate arsenic, arsine, and arsenic trioxide vapor in air and industrial process gas streams. In this train, a demister was used to remove droplets of water and oil, and particulates were removed by a filter. Vapor arsenic trioxide was collected in an impinger solution, and arsine gas was collected on silvered quartz beads. Hydrogen sulfide gas did not reduce the arsine trapping efficiency of the silvered beads, and charcoal proved to be an effective trap for both arsine and arsenic trioxide vapor. 1 figure, 2 tables

Molybdenum oxide nanowires based supercapacitors with enhanced capacitance and energy density in ethylammonium nitrate electrolyte

Energy Technology Data Exchange (ETDEWEB)

Sarfraz, Mansoor; Aboud, Mohamed F.A.; Shakir, Imran, E-mail: shakir@skku.edu

2015-11-25

Orthorhombic molybdenum trioxide (α-MoO{sub 3}) nanowires as an electrode for electrochemical supercapacitors in ethylammonium nitrate (EAN) electrolyte exhibits a high specific capacitance of 288 Fg{sup −1}, which is 8 times higher than the specific capacitance obtained from MoO{sub 3} nanowires in water based electrolyte. MoO{sub 3} nanowires in EAN electrolyte exhibit energy density of 46.32 Wh kg{sup −1} at a power density of 20.3 kW kg{sup −1} with outstanding cycling stability with specific capacitance retention of 96% over 3000 cycles. We believe that the superior performance of the MoO{sub 3} nanowires in EAN based electrolyte is primarily due to its relatively low viscosity (0.28 P at 25 °C), high electrical conductivity (20 mS cm{sup −1} at 25 °C) and large working voltage window. The results clearly demonstrate that EAN as electrolyte is one of the most promising electrolyte for high performance large scale energy storage devices. - Highlights: • Synthesis of single crystalline molybdenum oxide nanowires. • Ethylammonium Nitrate as an electrolyte for high performance large scale psuedocapacitor based energy storage devices. • Molybdenum oxide nanowires based electrodes shows 8 fold enhancement in Ethylammonium Nitrate electrolyte as compared to water based electrolytes. • The devices in Ethylammonium Nitrate exhibit excellent stability, retaining 96% of its initial capacity after 3000 cycles.

Molybdenum Disilicide Oxidation Kinetics in High Temperature Steam

Energy Technology Data Exchange (ETDEWEB)

Wood, Elizabeth Sooby [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Parker, Stephen Scott [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Nelson, Andrew Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-09-07

The Fuel Cycle Research and Development program’s Advanced Fuels Campaign is currently supporting a range of experimental efforts aimed at the development and qualification of ‘accident tolerant’ nuclear fuel forms. One route to enhance the accident tolerance of nuclear fuel is to replace the zirconium alloy cladding, which is prone to rapid oxidation in steam at elevated temperatures, with a more oxidation-resistant cladding. Several cladding replacement solutions have been envisaged. The cladding can be completely replaced with a more oxidation resistant alloy, a layered approach can be used to optimize the strength, creep resistance, and oxidation tolerance of various materials, or the existing zirconium alloy cladding can be coated with a more oxidation-resistant material. Molybdenum is one candidate cladding material favored due to its high temperature creep resistance. However, it performs poorly under autoclave testing and suffers degradation under high temperature steam oxidation exposure. Development of composite cladding architectures consisting of a molybdenum core shielded by a molybdenum disilicide (MoSi₂) coating is hypothesized to improve the performance of a Mo-based cladding system. MoSi₂ was identified based on its high temperature oxidation resistance in O₂ atmospheres (e.g. air and “wet air”). However, its behavior in H₂O is less known. This report presents thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and x-ray diffraction (XRD) results for MoSi₂ exposed to 670-1498 K water vapor. Synthetic air (80-20%, Ar-O₂) exposures were also performed, and those results are presented here for a comparative analysis. It was determined that MoSi₂ displays drastically different oxidation behavior in water vapor than in dry air. In the 670-1498 K temperature range, four distinct behaviors are observed. Parabolic oxidation is exhibited in only 670

Chemistry and Mechanism of Interaction Between Molybdenite Concentrate and Sodium Chloride When Heated in the Presence of Oxygen

Science.gov (United States)

Aleksandrov, P. V.; Medvedev, A. S.; Imideev, V. A.; Moskovskikh, D. O.

2017-04-01

Roasting of molybdenum concentrates with sodium chloride has high potential and can be an alternative to oxidizing roasting and autoclave leaching; however, the chemistry and mechanism are poorly known. The chemical mechanism of the roasting process between molybdenite concentrate and sodium chloride in the presence of atmospheric oxygen is proposed. It is demonstrated that the process occurs through molybdenite oxidation, up to molybdenum trioxide, with subsequent formation of sodium polymolybdates and molybdenum dioxydichloride from molybdenum trioxide. It is found that the formation of water-soluble sodium polymolybdates from molybdenum trioxide stops over time due to passivation of sodium chloride surface by polymolybdates. It is proved experimentally that preliminary grinding of the mixture in a furnace charge leads to an increase in the polymolybdate fraction of the roasting products, which constitutes approximately 65 pct of molybdenum initially in the roasted mixture against 20 to 22 pct in a nonground mixture (or 75 to 77 pct against 30 to 33 pct of molybdenum in calcine). For the first time, the presence of the Na2S2O7 phase in the calcine was confirmed experimentally. The suggested mechanism gives possible explanations for the sharp increase of MoO2Cl2 formation within the temperature range of 673 K to 723 K (400 °C to 450 °C) that is based on the catalytic reaction of molybdenum dioxydichloride from the Na2S2O7 liquid phase as it runs in a melt.

Vapor deposition of molybdenum oxide using bis(ethylbenzene) molybdenum and water

International Nuclear Information System (INIS)

Drake, Tasha L.; Stair, Peter C.

2016-01-01

Three molybdenum precursors—bis(acetylacetonate) dioxomolybdenum, molybdenum isopropoxide, and bis(ethylbenzene) molybdenum—were tested for molybdenum oxide vapor deposition. Quartz crystal microbalance studies were performed to monitor growth. Molybdenum isopropoxide and bis(ethylbenzene) molybdenum achieved linear growth rates 0.01 and 0.08 Å/cycle, respectively, using atomic layer deposition techniques. Negligible MoO_x growth was observed on alumina powder using molybdenum isopropoxide, as determined by inductively coupled plasma optical emission spectroscopy. Bis(ethylbenzene) molybdenum achieved loadings of 0.5, 1.1, and 1.9 Mo/nm"2 on alumina powder after one, two, and five cycles, respectively, using atomic layer deposition techniques. The growth window for bis(ethylbenzene) molybdenum is 135–150 °C. An alternative pulsing strategy was also developed for bis(ethylbenzene) molybdenum that results in higher growth rates in less time compared to atomic layer deposition techniques. The outlined process serves as a methodology for depositing molybdenum oxide for catalytic applications. All as-deposited materials undergo further calcination prior to characterization and testing.

The investigation of the kinetics of hydrochemical oxidation of metal sulphides with the aim of determination of the optimal conditions for the selective extraction of molybdenum from ores

Directory of Open Access Journals (Sweden)

Lutsik V.

2005-01-01

Full Text Available The kinetics of the oxidation of molybdenyte, pyrite and sphalerite in solutions of nitric acid, hydrogen peroxide, and sodium hypochlorite was studied by the rotating disk method. The influence of the molar concentration of reagent, pH of solution, temperature, disk rotation frequency, and duration of measurements on the specific rate of hydrochemical oxidation of sulpfides was determined. The kinetic models allowing to calculate the dissolution rate of sulphides when these parameters change simultaneously were obtained. The conditions of kinetically and diffusion-controlled processes were detected. The details of mechanism of the studied processes were revealed. The nature of intermediate solid products, the reasons and the conditions of their formation as well as the character of their influence on the kinetics of dissolution processes were determined. The probable schemes of interactions corresponding to the observable kinetic dependences were offered. The conditions of the effective and selective molybdenum leaching directly from ore without its concentration were found.

Programming voltage reduction in phase change memory cells with tungsten trioxide bottom heating layer/electrode

International Nuclear Information System (INIS)

Rao Feng; Song Zhitang; Gong Yuefeng; Wu Liangcai; Feng Songlin; Chen, Bomy

2008-01-01

A phase change memory cell with tungsten trioxide bottom heating layer/electrode is investigated. The crystalline tungsten trioxide heating layer promotes the temperature rise in the Ge 2 Sb 2 Te 5 layer which causes the reduction in the reset voltage compared to a conventional phase change memory cell. Theoretical thermal simulation and calculation for the reset process are applied to understand the thermal effect of the tungsten trioxide heating layer/electrode. The improvement in thermal efficiency of the PCM cell mainly originates from the low thermal conductivity of the crystalline tungsten trioxide material.

The potential DNA toxic changes among workers exposed to antimony trioxide.

Science.gov (United States)

El Shanawany, Safaa; Foda, Nermine; Hashad, Doaa I; Salama, Naglaa; Sobh, Zahraa

2017-05-01

Occupational exposure to antimony has gained much interest when specific toxic effects were noticed among workers processing antimony. Thus, the aim of the present work was to investigate the potential DNA oxidative damage occurring among Egyptian workers occupationally exposed to antimony trioxide. The study was conducted on 25 subjects exposed to antimony trioxide while working in the polymerization process of polyester in Misrayon and Polyester Fiber Company, KafrEldawwar, Beheira, Egypt. Urinary antimony levels were assessed using inductive coupled plasma-optical emission spectrometry (ICP-OES) and considered as a biological exposure index. DNA damage and total oxidant capacity (TOC) were assessed using ELISA. DNA damage was detected in the form of increased apurinic/apyrimidinic (AP) sites among antimony trioxide-exposed workers compared to control subjects, but it could not be explained by oxidative mechanisms due to lack of significant correlation between DNA damage and measured TOC. Antimony trioxide might have a genotoxic impact on occupationally exposed workers which could not be attributed to oxidative stress in the studied cases.

Structure, activity and kinetics of supported molybdenum oxide and mixed molybdenum-vanadium oxide catalysts prepared by flame spray pyrolysis for propane OHD

DEFF Research Database (Denmark)

Høj, Martin; Kessler, Thomas; Beato, Pablo

2013-01-01

reflectance UV-vis spectroscopy and evaluated as catalysts for the oxidative dehydrogenation (ODH) of propane. The results show that samples with high specific surface areas between 122 and 182 m2/g were obtained, resulting in apparent MoOx and VOx surface densities from 0.7 to 7.7 nm -2 and 1.5 to 1.9 nm-2......, respectively. Raman spectroscopy, UV-vis spectroscopy and XRD confirmed the high dispersion of molybdenum and vanadia species on γ-Al2O3 as the main crystalline phase. Only at the highest loading of 15 wt% Mo, with theoretically more than monolayer coverage, some crystalline molybdenum oxide was observed...

Molybdenum extraction from copper-molybdenum ores

International Nuclear Information System (INIS)

Nevaeva, L.M.

1982-01-01

Molybdenum extraction from copper-molybdenum ores as practised in different countries is reviewed. In world practice the production process including depression of copper and iron sulfides and flotation of molybdenite is widely spread. At two USA factories the process of a selective flotation with molybdenite depression by dextrin is used

Kinetics of molybdenum and chlorine interaction

International Nuclear Information System (INIS)

Zelikman, A.N.; Nazarov, Yu.N.; Sarkarov, T.Eh.; Tulyakov, N.V.

1977-01-01

The kinetics is studied of molybdenite chlorination with gaseous chlorine. The time dependences of the depth and degree of molybdenite chlorination are given along with the dependence on chlorine concentration of molybdenite chlorination rate. Active interaction is shown to take place at 450-470 deg C. At 350-435 deg C, chlorination occurs in the kinetic range, the apparent activation energy being equal to 22.2 kcal/mole and the order of reaction by chlorine to 0.77. At 435-610 deg C, the process takes place in the diffusion range and is restricted by dissipation of the reaction products (activation energy - 4.05 kcal/mole; order of reaction by chlorine - 0.6)

Mineral Trioxide Aggregate and Portland Cement for Direct Pulp Capping in Dog: A Histopathological Evaluation

Directory of Open Access Journals (Sweden)

Maryam Bidar

2014-09-01

Full Text Available Background and aims. Mineral trioxide aggregate and calcium hydroxide are considered the gold standard pulp-capping materials. Recently, Portland cement has been introduced with properties similar to those of mineral trioxide aggregate. His-topathological effects of direct pulp capping using mineral trioxide aggregate and Portland cements on dog dental pulp tis-sue were evaluated in the present study. Materials and methods. This histopatological study was carried out on 64 dog premolars. First, the pulp was exposedwith a sterile bur. Then, the exposed pulp was capped with white or gray mineral trioxide aggregates and white or gray Port-land cements in each quadrant and sealed with glass-ionomer. The specimens were evaluated under a light microscope after 6 months. Statistical analysis was carried out using Kruskal-Wallis test. Statistical significance was defined at α=5%. Results. There was no acute inflammation in any of the specimens. Chronic inflammation in white and gray mineral triox-ide aggregates and white and gray Portland cements was reported to be 45.5%, 27.3%, 57.1% and 34.1%, respectively. Al-though the differences were not statistically significant, severe inflammation was observed mostly adjacent to white mineral trioxide aggregate. The largest extent of increased vascularization (45% and the least increase in fibrous tissue were ob-served adjacent to white mineral trioxide aggregate, with no significant differences. In addition, the least calcified tissue formed adjacent to white mineral trioxide aggregate, although the difference was not significant. Conclusion. The materials used in this study were equally effective as pulp protection materials following direct pulp cap-ping in dog teeth.

Influence of macroscopic shear deformation on polygonization and recrystallization of molybdenum crystals

International Nuclear Information System (INIS)

Larikov, L.N.; Belyakova, M.N.; Maksimenko, E.A.; Mudruk, P.V.

1984-01-01

The effect of shear bands on polygonization and recrystallization is studied on molybdenum monocrystals deformed by compression. A sharp bend of the lattice is shown to be a structural condition necessary for arising the shear step. Internal stress relaxation strongly changes kinetics of softening processes in compressed molybdenum crystals: it slows down polygonization under low-temperature heating (below 700 deg C) and accelerates it under high-temperature heating (higher 1000 deg C). Under the effect of relaxation of internal streses recrystallization in the investigated crystals is similar to dynamical: recrystallized grains are distorted and they have a developed substructure

Effect of oxidizing environment on mechanical properties of molybdenum and TZM

International Nuclear Information System (INIS)

Liu, C.T.; Anderson, S.H.; Inouye, H.

1978-10-01

The effect of environment on mechanical properties of molybdenum and TZM was investigated in low-pressure (1.3-mPa) oxygen at 1150 0 C. Specimens of TZM picked up oxygen and lost carbon. The oxygen concentration increases linearly with exposure time, indicating that the chemisorption of oxygen molecules at the specimen surface, rather than bulk diffusion, controls the kinetics of oxygen absorption at 1150 0 C. Specimens of TZM increase in tensile strength and decrease in ductility with increasing oxygen content. Exposed TZM loses its ductility at elevated temperatures at an oxygen level of 500 ppM. The embrittlement is due to the formation of zones or oxide precipitates, which harden the alloy and promote the brittle fracture associated with cleavage and grain-boundary separation. Unalloyed molybdenum responds to the oxidizing environment quite differently from TZM. The molybdenum (containing no active element such as Ti and Zr) showed no internal oxidation at 1150 0 C. Instead, our results indicate that a trace of oxygen penetrated into molybdenum through its grain boundaries. This penetration raises the ductile-to-brittle transition temperature of molybdenum by 200 0 C lowers the ductility above 900 0 C. The ductility of oxygen-exposed molybdenum is virtually unaffected in the temperature range from 400 to 900 0 C. A ductility minimum (10%) is observed at 1350 0 C because of dynamic embrittlement effects; that is, diffusion of oxygen to grain boundaries or crack tips where high triaxial states of stress are generated during plastic deformation. This embrittlement can be totally eliminated by an increase in strain rate

Investigation into electrochemical behavior of molybdenum VM-1 alloy at high current density

Energy Technology Data Exchange (ETDEWEB)

Tatarinova, O M; Amirkhanova, N A; Akhmadiev, A G

1975-01-01

The effect of the composition and concentration of electrolyte on the workability of the molybdenum VM-1 alloy has been studied and a number of anions has been determined relative to their activation capacity. The best workability of the alloy is achieved in a 15% NaOH solution and a composite electrolyte 15% NaNO/sub 3/+5%NaOH. It is shown that in polarization of the VM-1 alloy both in alkali- and salt solutions a film of oxides of different valence molybdenum is formed: Mo/sub 2/O/sub 3/, Mo/sub 4/O/sub 11/, Mo/sub 9/O/sub 26/, MoO/sub 3/, but molybdenum gets dissolved only in a hexavalent form, its content in a solution being in conformity with the polarizing current densities. Using a temperature-kinetic technique it has been found that the concentrational polarization is the limiting stage in the reaction of molybdenum and VM-1 alloy anodic dissolution in 15% NaNO/sub 3/ solution and in the composite electrolyte 15%NaNO/sub 3/+5%NaOH.

Surface composition of carburized tungsten trioxide and its catalytic activity

International Nuclear Information System (INIS)

Nakazawa, M.; Okamoto, H.

1985-01-01

The surface composition and electronic structure of carburized tungsten trioxide are investigated using x-ray photoelectron spectroscopy (XPS). The relationship between the surface composition and the catalytic activity for methanol electro-oxidation is clarified. The tungsten carbide concentration in the surface layer increases with the carburization time. The formation of tungsten carbide enhances the catalytic activity. On the other hand, the presence of free carbon or tungsten trioxide in the surface layer reduces the activity remarkably. It is also shown that, the higher the electronic density of states near the Fermi level, the higher the catalytic activity

Polaron interaction energies in reduced tungsten trioxide

International Nuclear Information System (INIS)

Iguchi, E.; Salje, E.; Tilley, R.J.D.

1981-01-01

Consideration of the properties of reduced tungsten trioxide suggest that the mobile charge carriers are polarons. As it is uncertain how the presence of polarons will influence the microstructures of the crystallographic shear (CS) planes present in reduced tungsten trioxide we have calculated both the polaron-CS plane and polaron-polaron interaction energy for a variety of circumstances. Three CS plane geometries were considered, (102), (103), and (001) CS plane arrays, and the nominal compositions of the crystals ranged from WO 2 70 to WO 3 0 . The polarons were assumed to have radii from 0.6 to 1.0 nm and the polaron-CS plane electrostatic interaction was assumed to be screened. The results suggest that for the most part the total interaction energy is small and is unlikely to be of major importance in controlling the microstructures found in CS planes. However, at very high polaron densities the interaction energy could be appreciable and may have some influence on the existence range of CS phases

Evaluation of oxide dispersion strengthened (ODS) molybdenum and molybdenum-rhenium alloys

International Nuclear Information System (INIS)

Mueller, A.J.; Bianco, R.; Buckman, R.W. Jr.

1999-01-01

Oxide dispersion strengthened (ODS) molybdenum alloys being developed for high temperature applications possess excellent high temperature strength and creep resistance. In addition they exhibit a ductile-to-brittle transition temperature (DBIT) in the worked and stress-relieved condition under longitudinal tensile load well below room temperature. However, in the recrystallized condition, the DBTT maybe near or above room temperature, depending on the volume fraction of oxide dispersion and the amount of prior work. Dilute rhenium additions (7 and 14 wt.%) to ODS molybdenum were evaluated to determine their effect on low temperature ductility. The addition of 7 wt.% rhenium to the ODS molybdenum did not significantly enhance the mechanical properties. However, the addition of 14 wt.% rhenium to the ODS molybdenum resulted in a DBTT well below room temperature in both the stress-relieved and recrystallized condition. Additionally, the tensile strength of ODS Mo-14Re is greater than the base ODS molybdenum at 1,000 to 1,250 C

Thermodynamic and kinetic studies of As2O3 toxicological effects on human insulin in generation diabetes mellitus

Science.gov (United States)

Mohsennia, Mohsen; Motaharinejad, Atieh; Rafiee-Pour, Hossain-Ali; Torabbeigi, Marzieh

2017-12-01

The interaction of arsenic trioxide with human insulin was investigated by circular dichroism (CD), cyclic voltammetry and electrophoresis techniques. The interfacial behavior of insulin in presence of As2O3 onto the Ag electrode surface was studied at 310 K in phosphate buffer solution (PBS). According to Far-UV CD spectroscopy results, As2O3 caused to decrease in structural compactness and variety of alpha helix into beta structures. Near-UV CD indicated that As2O3 dissociates disulfide linkage in insulin structure. The kinetic parameters, including charge-transfer coefficient and apparent heterogeneous electron transfer rate constant were also determined. The thermodynamic parameters of insulin denaturation in presence of arsenic trioxide were calculated and reported. The obtained results indicated strong adsorption of insulin in presence of arsenic trioxide onto the Ag surface via chemisorptions.

The role of oxygen in porous molybdenum electrodes for the alkali metal thermoelectric converter

International Nuclear Information System (INIS)

Williams, R.M.; Nagasubramanian, G.; Khanna, S.K.; Bankston, C.P.; Thakoor, A.P.; Cole, T.

1986-01-01

The alkali metal thermoelectric converter is a direct energy conversion device, utilizing a high alkali metal activity gradient to generate electrical power. Its operation is based on the unique ion conductive properties of beta''-alumina solid electrolyte. The major barrier to application of this device is identification of an electrode which can maintain optimum power densities for operation times of >10,000h. Thin, porous molybdenum electrodes have shown the best performance characteristics, but show a variety of time dependent phenomena, including eventual degradation to power densities 3-5 times lower than initial values. Several Na-Mo-O compounds, including Na/sub 2/MoO/sub 4/ and Na/sub 2/Mo/sub 3/O/sub 6/, are formed during AMTEC operation. These compounds may be responsible for enhanced Na transport through Mo electrodes via sodium ion conduction, and eventual performance degradation due to their volatilization and decomposition. No decomposition of beta''-alumina has been observed under simulated AMTEC operating conditions up to 1373 K. In this paper, we present a model for chemical reactions occurring in porous molybdenum electrodes. The model is based on thermochemical and kinetic data, known sodium-molybdenum-oxygen chemistry, x-ray diffraction analysis of molybdenum and molybdenum oxide electrodes, and the electrochemical behavior of the cell

Expression of cyclin A in A549 cell line after treatment with arsenic trioxide

Directory of Open Access Journals (Sweden)

Agnieszka Żuryń

2015-12-01

Full Text Available Background: Arsenic trioxide (ATO is an effective drug used in acute promyelocytic leukemia (AML. Many reports suggest that ATO can also be applied as an anticancer agent for solid tumors in the future. The influence of arsenic trioxide on the expression of different cell cycle regulators is poorly recognized. The purpose of the current study is to investigate how arsenic trioxide affects cyclin A expression and localization in the A549 cell line.Materials and methods: Morphological and ultrastructural changes in A549 cells were observed using light and transmission electron microscopes. Cyclin A localization was determined by immunofluorescence. Image-based cytometry was applied to evaluate the effect of arsenic trioxide on apoptosis and the cell cycle. Expression of cyclin A mRNA was quantified by real-time PCR.Results: After treatment with arsenic trioxide, increased numbers of cells with cytoplasmic localization of cyclin A were observed. The doses of 10 and 15 μM ATO slightly reduced expression of cyclin A mRNA. The apoptotic phenotype of cells was poorly represented, and the Tali imagebased cytometry analysis showed low percentages of apoptotic cells. The A549 population displayed an enriched fraction of cells in G0/G1 phase in the presence of 5μM ATO, whereas starting from the higher concentrations of the drug, i.e. 10 and 15 μM ATO, the G2/M fraction was on the increase.Discussion: Low expression of cyclin A in the A549 cell line may constitute a potential factor determining arsenic trioxide resistance. It could be hypothesized that the observed alterations in cyclin A expression/distribution may correlate well with changes in cell cycle regulation in our model, which in turn determines the outcome of the treatment.

"Hexagonal molybdenum trioxide"--known for 100 years and still a fount of new discoveries.

Science.gov (United States)

Lunk, Hans-Joachim; Hartl, Hans; Hartl, Monika A; Fait, Martin J G; Shenderovich, Ilya G; Feist, Michael; Frisk, Timothy A; Daemen, Luke L; Mauder, Daniel; Eckelt, Reinhard; Gurinov, Andrey A

2010-10-18

In 1906, the preparation of “molybdic acid hydrate” was published by Arthur Rosenheim. Over the past 40 years, a multitude of isostructural compounds, which exist within a wide phase range of the system MoO3−NH3−H2O, have been published. The reported molecular formulas of “hexagonal molybdenum oxide” varied from MoO3 to MoO3·0.33NH3 to MoO3·nH2O (0.09 ≤ n ≤ 0.69) to MoO3·mNH3·nH2O (0.09 ≤ m ≤ 0.20; 0.18 ≤ n ≤ 0.60). Samples, prepared by the acidification route were investigated using thermal analysis coupled online to a mass spectrometer for evolved gas analysis, X-ray powder diffraction, Fourier transform infrared, Raman, magic-angle-spinning 1H- and 15N NMR spectroscopy, and incoherent inelastic neutron scattering. A comprehensive characterization of these samples will lead to a better understanding of their structure and physical properties as well as uncover the underlying relationship between the various compositions. The synthesized polymeric parent samples can be represented by the structural formula (NH4)(x∞)(3)[Mo(y square 1−y)O(3y)(OH)(x)(H2O)(m−n)]·nH2O with 0.10 ≤ x ≤ 0.14, 0.84 ≤ y ≤ 0.88, and m + n ≥ 3 − x − 3y. The X-ray study of a selected monocrystal confirmed the presence of the well-known 3D framework of edge- and corner-sharing MoO6 octahedra. The colorless monocrystal crystallizes in the hexagonal system with space group P6(3)/m, Z = 6, and unit cell parameters of a = 10.527(1) Å, c = 3.7245(7) Å, V = 357.44(8) Å3, and ρ = 3.73 g·cm(−3). The structure of the prepared monocrystal can best be described by the structural formula (NH4)(0.13∞)(3)[Mo(0.86 square 0.14)O2.58(OH)0.13(H2O)(0.29−n)]·nH2O, which is consistent with the existence of one vacancy (square) for six molybdenum sites. The sample MoO3·0.326NH3·0.343H2O, prepared by the ammoniation of a partially dehydrated MoO3·0.170NH3·0.153H2O with dry gaseous ammonia, accommodates NH3 in the hexagonal tunnels, in addition to [NH4

Potentiometric determination of molybdenum

International Nuclear Information System (INIS)

Rusina, O.N.; Gorbatkova, B.Kh.

1977-01-01

Potentiometric titration by lead acetate is used to determine molybdenum in the form of molybdate ions. The behaviour of bimetallic electrode couples, i.e. tungsten-lead, platinum-lead, lead-carbon electrode, molybdenum-carbon electrode platinum-molibdenum has been investigated. The greatest jump of the potential in the finite point is observed for platinum-molybdenum electrode couple (150 mV/ml at pH 4.0-5.5). The limiting concentration of molybdenum in potentiometric titration by lead acetate is 2.8x10 -4 M. The measurements are accurate to within +-0.1%

Characterization, non-isothermal decomposition kinetics and photocatalytic water splitting of green chemically synthesized polyoxoanions of molybdenum containing phosphorus as hetero atom

International Nuclear Information System (INIS)

D’Cruz, Bessy; Samuel, Jadu; George, Leena

2014-01-01

Highlights: • CPM nanorods were synthesized by applying the principles of green chemistry. • The isoconversional method was used to analyze the effective activation energy. • The appropriate reaction models of the two decomposition stages were determined. • Photocatalytic water splitting was investigated in the presence of platinum co-catalyst. - Abstract: In here, the green synthesis and thermal characterization of a novel polyoxoanions of molybdenum containing phosphorus as hetero atom are reported. The composition and morphology of the nanorods were established by fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and inductively coupled plasma atomic emission spectroscopic (ICP-AES) techniques. Thermal properties of the nanoparticles were investigated by non-isothermal analysis under nitrogen atmosphere. The values activation energy of each stage of thermal decomposition for all heating rates was calculated by Flynn–Wall–Ozawa (FWO) and Kissinger–Akahira–Sunnose (KAS) methods. Invariant kinetic parameter (IKP) method and master plot method were also used to evaluate the kinetic parameters and mechanism for the thermal decomposition of cetylpyridinium phosphomolybdate (CPM). Photocatalytic water oxidation mechanism using CPM catalyst in the presence of platinum (Pt) co-catalyst enhances the H 2 evolution and was found to be 1.514 mmol/g/h

Characterization, non-isothermal decomposition kinetics and photocatalytic water splitting of green chemically synthesized polyoxoanions of molybdenum containing phosphorus as hetero atom

Energy Technology Data Exchange (ETDEWEB)

D’Cruz, Bessy [Department of Chemistry, Mar Ivanios College, Thiruvananthapuram 695015 (India); Samuel, Jadu, E-mail: jadu_samuel@yahoo.co.in [Department of Chemistry, Mar Ivanios College, Thiruvananthapuram 695015 (India); George, Leena [Catalysis and Inorganic Chemistry Division, National Chemical Laboratory, Pune 411008 (India)

2014-11-20

Highlights: • CPM nanorods were synthesized by applying the principles of green chemistry. • The isoconversional method was used to analyze the effective activation energy. • The appropriate reaction models of the two decomposition stages were determined. • Photocatalytic water splitting was investigated in the presence of platinum co-catalyst. - Abstract: In here, the green synthesis and thermal characterization of a novel polyoxoanions of molybdenum containing phosphorus as hetero atom are reported. The composition and morphology of the nanorods were established by fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and inductively coupled plasma atomic emission spectroscopic (ICP-AES) techniques. Thermal properties of the nanoparticles were investigated by non-isothermal analysis under nitrogen atmosphere. The values activation energy of each stage of thermal decomposition for all heating rates was calculated by Flynn–Wall–Ozawa (FWO) and Kissinger–Akahira–Sunnose (KAS) methods. Invariant kinetic parameter (IKP) method and master plot method were also used to evaluate the kinetic parameters and mechanism for the thermal decomposition of cetylpyridinium phosphomolybdate (CPM). Photocatalytic water oxidation mechanism using CPM catalyst in the presence of platinum (Pt) co-catalyst enhances the H{sub 2} evolution and was found to be 1.514 mmol/g/h.

Determination of rhenium in ores of complex composition by the kinetic method

Energy Technology Data Exchange (ETDEWEB)

Pavlova, L G; Gurkina, T V [Kazakhskij Gosudarstvennyj Univ., Alma-Ata (USSR); Tsentral' naya Lab. Yuzhno-Kazakhstanskogo Geologicheskogo Upravleniya, Alma-Ata (USSR))

1979-09-01

The kinetic rhenium determination method is proposed based on rhenium catalytic effect in the reaction of malachite green with thiourea. The accompanying elements, excluding molybdenum, do not interfere with the rhenium determination at their concentration of up to 0.1 M. The interfering influence of molybdenum can be eliminated by addition of tartaric acid to the solution up to the concentration of 0.1 M. This enables to determine rhenium in presence of 1000-fold quantity of molybdenum. The method is applicable for the analysis of complex copper-zinc sulphide ores.

Ambient pressure hydrometallurgical conversion of arsenic trioxide to crystalline scorodite

Energy Technology Data Exchange (ETDEWEB)

Debekaussen, R. [Corus Consulting and Technical Services, Delft (Netherlands); Droppert, D. [Solumet Inc., Montreal, PQ (Canada); Demopoulos, G. P. [McGill Univ., Dept. of Metallurgical Enginering, Montreal, PQ (Canada)

2001-06-01

Development of a novel process for the ambient pressure conversion of arsenic trioxide, a common, but extremely toxic by-product of the non-ferrous smelting industry, is described. The process consists of three main stages; (1) dissolution of arsenic trioxide, (2) oxidation of trivalent arsenic with the addition of hydrogen peroxide at 95 degree C, to pentavalent arsenic, and (3) step-wise precipitation of crystalline scorodite from highly concentrated arsenic containing solutions, by operating below a characteristics induction pH in the presence of seed material. The technical feasibility of the process has been confirmed by bench-scale testing of industrial flue dust material or acid plant effluents. 30 refs., 2 tabs., 5 figs.

Analytic chemistry of molybdenum

International Nuclear Information System (INIS)

Parker, G.A.

1983-01-01

Electrochemical, colorimetric, gravimetric, spectroscopic, and radiochemical methods for the determination of molybdenum are summarized in this book. Some laboratory procedures are described in detail while literature citations are given for others. The reader is also referred to older comprehensive reviews of the analytical chemistry of molybdenum. Contents, abridged: Gravimetric methods. Titrimetric methods. Colorimetric methods. X-ray fluorescence. Voltammetry. Catalytic methods. Molybdenum in non-ferrous alloys. Molydbenum compounds

Molybdenum from uranium solutions

International Nuclear Information System (INIS)

Gardner, H.E.

1981-01-01

A method of removing molybdenum from a uranium bearing solution is claimed. It comprises adding sufficient reactive lead compound to supply at least 90 percent of the stoichiometric quantity of lead ion required to fully react with the molybdenum present to form insoluble lead molybdate and continuing the reaction with agitation until the desired percentage of the molybdenum present has reacted with the lead ion

Bibliographic study on molybdenum biokinetics

International Nuclear Information System (INIS)

Erzberger, A.

1988-05-01

This bibliographical study compiles and analyzes findings about the metabolism and resorption of molybdenum. Besides including studies on the physiology of molybdenum 99, a general survey is given on molybdenum in the environment and on its physiological behaviour. In particular, information on the dependence of molybdenum resorption on various factors, such as the chemical form, antagonisms etc., are gathered from literature. These factors have to be considered for sensibly carrying out necessary experiments. (orig./MG) [de

Arsenic trioxide mediates HAPI microglia inflammatory response and subsequent neuron apoptosis through p38/JNK MAPK/STAT3 pathway

International Nuclear Information System (INIS)

Mao, Jiamin; Yang, Jianbing; Zhang, Yan; Li, Ting; Wang, Cheng; Xu, Lingfei; Hu, Qiaoyun; Wang, Xiaoke; Jiang, Shengyang; Nie, Xiaoke; Chen, Gang

2016-01-01

Arsenic is a widely distributed toxic metalloid all over the world. Inorganic arsenic species are supposed to affect astrocytic functions and to cause neuron apoptosis in CNS. Microglias are the key cell type involved in innate immune responses in CNS, and microglia activation has been linked to inflammation and neurotoxicity. In this study, using ELISA, we showed that Arsenic trioxide up-regulated the expression and secretion of IL-1β in a dose-dependent manner and a time-dependent manner in cultured HAPI microglia cells. The secretion of IL-1β caused the apoptosis of SH-SY5Y. These pro-inflammatory responses were inhibited by the STAT3 blocker, AG490 and P38/JNK MAPK blockers SB202190, SP600125. Further, Arsenic trioxide exposure could induce phosphorylation and activation of STAT3, and the translocation of STAT3 from the cytosol to the nucleus in this HAPI microglia cell line. Thus, the STAT3 signaling pathway can be activated after Arsenic trioxide treatment. However, P38/JNK MAPK blockers SB202190, SP600125 also obviously attenuated STAT3 activation and transnuclear transport induced by Arsenic trioxide. In concert with these results, we highlighted that the secretion of IL-1β and STAT3 activation induced by Arsenic trioxide can be mediated by elevation of P38/JNK MAPK in HAPI microglia cells and then induced the toxicity of neurons. - Highlights: • Arsenic trioxide exposure induced expression of IL-β in HAPI microglia. • Arsenic trioxide exposure induced activation of MAPK pathways in HAPI microglia. • Arsenic trioxide exposure induced activation of STAT3 pathways in HAPI microglia. • The expression of IL-β though P38/JNK MAPK/STAT3 pathways in HAPI microglia.

Arsenic trioxide mediates HAPI microglia inflammatory response and subsequent neuron apoptosis through p38/JNK MAPK/STAT3 pathway

Energy Technology Data Exchange (ETDEWEB)

Mao, Jiamin [Department of Environmental Health, School of Public Health, Nantong University, Nantong, Jiangsu 226001 (China); Yang, Jianbing [Department of Pediatrics, Affiliated Hospital of Nantong University, Nantong, Jiangsu 226001 (China); Zhang, Yan [Department of Nutrition and Food Hygiene, School of Public Health, Nantong University, Nantong, Jiangsu 226001 (China); Li, Ting [Department of Environmental Health, School of Public Health, Nantong University, Nantong, Jiangsu 226001 (China); Wang, Cheng [Department of Nutrition and Food Hygiene, School of Public Health, Nantong University, Nantong, Jiangsu 226001 (China); Xu, Lingfei; Hu, Qiaoyun; Wang, Xiaoke; Jiang, Shengyang [Department of Environmental Health, School of Public Health, Nantong University, Nantong, Jiangsu 226001 (China); Nie, Xiaoke [Department of Nutrition and Food Hygiene, School of Public Health, Nantong University, Nantong, Jiangsu 226001 (China); Chen, Gang, E-mail: chengang@ntu.edu.cn [Department of Environmental Health, School of Public Health, Nantong University, Nantong, Jiangsu 226001 (China)

2016-07-15

Arsenic is a widely distributed toxic metalloid all over the world. Inorganic arsenic species are supposed to affect astrocytic functions and to cause neuron apoptosis in CNS. Microglias are the key cell type involved in innate immune responses in CNS, and microglia activation has been linked to inflammation and neurotoxicity. In this study, using ELISA, we showed that Arsenic trioxide up-regulated the expression and secretion of IL-1β in a dose-dependent manner and a time-dependent manner in cultured HAPI microglia cells. The secretion of IL-1β caused the apoptosis of SH-SY5Y. These pro-inflammatory responses were inhibited by the STAT3 blocker, AG490 and P38/JNK MAPK blockers SB202190, SP600125. Further, Arsenic trioxide exposure could induce phosphorylation and activation of STAT3, and the translocation of STAT3 from the cytosol to the nucleus in this HAPI microglia cell line. Thus, the STAT3 signaling pathway can be activated after Arsenic trioxide treatment. However, P38/JNK MAPK blockers SB202190, SP600125 also obviously attenuated STAT3 activation and transnuclear transport induced by Arsenic trioxide. In concert with these results, we highlighted that the secretion of IL-1β and STAT3 activation induced by Arsenic trioxide can be mediated by elevation of P38/JNK MAPK in HAPI microglia cells and then induced the toxicity of neurons. - Highlights: • Arsenic trioxide exposure induced expression of IL-β in HAPI microglia. • Arsenic trioxide exposure induced activation of MAPK pathways in HAPI microglia. • Arsenic trioxide exposure induced activation of STAT3 pathways in HAPI microglia. • The expression of IL-β though P38/JNK MAPK/STAT3 pathways in HAPI microglia.

Kinetics of chemical vapor deposition of boron on molybdenum

International Nuclear Information System (INIS)

Tanaka, H.; Nakanishi, N.; Kato, E.

1987-01-01

Experimental rate data of chemical vapor deposition of boron by reduction of boron trichloride with hydrogen are analyzed to determine the reaction mechanism. The experiments were conducted at atmospheric pressure. The weight change of the sample was noted by means of a thermobalance. Molybdenum was used as the substrate. It has been found that the outer layer of the deposited film is Mo/sub 2/B/sub 5/ and the inner layer is MoB, and in the stational state of the reaction, the diffusion in the solid state is considered not to be rate controlling. When mass transport limitation was absent, the reaction orders with respect to boron trichloride and hydrogen were one third and one half, respectively. By comparing these orders with those obtained from Langmuir-Hinshelwood type equations, the rate controlling mechanism is identified to be the desorption of hydrogen chloride from the substrate

Clinical Assessment of Mineral Trioxide Aggregate in the Treatment ...

African Journals Online (AJOL)

2017-05-22

May 22, 2017 ... (OH)2 (n = 49) or MTA (n = 51) and restored with composite resin in 73 patients. Periapical ... Clinical Assessment of Mineral Trioxide Aggregate in the Treatment of .... materials, light-cured glass ionomer cement base (Riva.

The influence of particle size on intermediate and final stages of molybdenum sintering

International Nuclear Information System (INIS)

Uskokovic, D.; Novakovic, B.; Petrovic, V.; Ristic, M.M.

1982-01-01

The influence of initial particle size on kinetics of molybdenum sintering was investigated. Three fractions of monodispersed molybdenum powder (2, 5 and 10 μm) were used as well as a polydispersed powder with mean particle size of 12 μm. Decrease in particle size accelerates to a great extent densification and grain growth processes. During sintering of 10 μm powder and to a smaller extent in the case of polydispersed powder, Zeners's relation was confirmed. Quantitative equations for the intermediate sintering stages could not be fitted to the investigated particulate systems, even though the grain growth process could be described by cubic law and though the volume diffusion coefficient and the surface energy were known with great reliability. (Auth.)

Kinetic of martensitic transformations induced by hydrogen in the austenite

International Nuclear Information System (INIS)

Oliveira, Sergio P. de; Saavedra, A.; Miranda, P.E.V. de

1986-01-01

The X-ray diffractometry technique was used, with an automatic data acquisition system to determine the kinetics of hydrogen induced martensitic phase transformations in an AISI 304 austenitic stainless steel type, used in nuclear power plants. Hydrogenation was performed cathodically in a 1N sulfuric acid solution, containing 100 mg/l of arsenic trioxide, at 50 0 C, during 2 hours and with a current density of 200 A/m 2 . It was found that the microstructure of the steel plays a role on the generation of hydrogen induced martensitic phases and surface micro cracks. Both kinetics were slower on a pre-cold rolled steel. (Author) [pt

Molybdenum dioxide-molybdenite roasting

International Nuclear Information System (INIS)

Sabacky, B.J.; Hepworth, M.T.

1984-01-01

A process is disclosed for roasting molybdenite concentrates directly to molybdenum dioxide. The process comprises establishing a roasting zone having a temperature of about 700 0 C. to about 800 0 C., introducing into the roasting zone particulate molybdenum dioxide and molybdenite in a weight ratio of at least about 2:1 along with an oxygen-containing gas in amount sufficient to oxidize the sulfur content of the molybdenite to molybdenum dioxide

Relapsed acute promyelocytic leukemia in a hemodialysis-dependent patient treated with arsenic trioxide: a case report

Directory of Open Access Journals (Sweden)

Emmons Gregory S

2012-10-01

Full Text Available Abstract Introduction In the relapsed setting, arsenic trioxide remains the backbone of treatment. Scant literature exists regarding treatment of relapsed acute promyelocytic leukemia in patients with renal failure. To the best of our knowledge we are the first to report a safe and effective means of treatment for relapsed acute promyelocytic leukemia in the setting of advanced renal failure, employing titration of arsenic trioxide based on clinical parameters rather than arsenic trioxide levels. Case presentation A 33-year-old Caucasian man with a history of acute promyelocytic leukemia in remission for 3 years, as well as dialysis-dependent chronic renal failure secondary to a solitary kidney and focal segmental glomerulosclerosis and human immunodeficiency virus infection, receiving highly active antiretroviral therapy presented to our hospital with bone marrow biopsy-confirmed relapsed acute promyelocytic leukemia. Arsenic trioxide was begun at a low dose with dose escalation based only on side effect profile monitoring and not laboratory testing for induction as well as maintenance without undue toxicity. Our patient achieved and remains in complete hematologic and molecular remission as of this writing. Conclusion Arsenic trioxide can be used safely and effectively to treat acute promyelocytic leukemia in patients with advanced renal failure using careful monitoring of side effects rather than blood levels of arsenic to guide therapeutic dosing.

Retreatability of Root Canals Obturated using Mineral Trioxide ...

African Journals Online (AJOL)

2018-04-04

Apr 4, 2018 ... 2018 Nigerian Journal of Clinical Practice | Published by Wolters Kluwer ‑ Medknow. Background: ... remaining RCFM was evaluated using digital camera. The images ... trioxide aggregate-based and two resin-based sealers. Niger J Clin ... glass ionomer cement and the specimens were stored at. 37°C in ...

Evaluation of molybdenum and its alloys

International Nuclear Information System (INIS)

Lundberg, L.B.

1981-01-01

The choice of pure molybdenum as the prime candidate material for space reactor core heat pipes is critically examined. Pure molybdenum's high ductile-brittle transition temperature appears to be its major disadvantage. The candidate materials examined in detail for this application include low carbon arc-cast molybdenum, TZM-molybdenum alloy, and molybdenum-rhenium alloys. Published engineering properties are collected and compared, and it appears that Mo-Re alloys with 10 to 15% rhenium offer the best combination. Hardware is presently being made from electron beam melted Mo-13Re to test this conclusion

Dose- and Time-Dependent Response of Human Leukemia (HL-60 Cells to Arsenic Trioxide Treatment

Directory of Open Access Journals (Sweden)

Paul B. Tchounwou

2006-06-01

Full Text Available The treatment of acute promyelocytic leukemia (APL has been based on the administration of all-trans retinoic acid plus anthracycline chemotherapy, which is very effective as first line therapy; however 25 to 30% of patients will relapse with their disease becoming refractory to conventional therapy. Recently, studies have shown arsenic trioxide to be effective in the treatment of acute promyelocytic leukemia. In this study, we used the human leukemia (HL-60 cell line as a model to evaluate the cytoxicity of arsenic trioxide based on the MTT assay. Data obtained from this assay indicated that arsenic trioxide significantly reduced the viability of HL-60 cells, showing LD50 values of 14.26 + 0.5μg/mL, 12.54 + 0.3μg/mL, and 6.4 + 0.6μg/mL upon 6, 12, and 24 hours of exposure, respectively; indicating a dose- and time-dependent response relationship. Findings from the present study indicate that arsenic trioxide is highly cytotoxic to human leukemia (HL-60 cells, supporting its use as an effective therapeutic agent in the management of acute promyelocytic leukemia.

Recovery of uranium and molybdenum from a carbonate type uranium-molybdenum ore

International Nuclear Information System (INIS)

Zhou Genmao; Zeng Yijun; Tang Baobin; Meng Shu; Xu Guolong

2014-01-01

Based on the results of process mineralogical research of a carbonate type uranium-molybdenum ore, leaching behaviors of the uranium-molybdenum ore were studied by alkali agitation leaching, conventional alkali column leaching and alkali curing column leaching processes. The results showed that using the alkali curing column leaching process, the leaching rate of molybdenum increased to more than 90%, and the leaching rate of uranium was about 85%, Compared with the conventional alkali column leaching process, the leaching time of the alkali curing column leaching process decreased by 60 days. (authors)

In-situ field-ion microscope study of the recovery behavior of heavy metal ion-irradiated tungsten, tungsten (rhenium) alloys and molybdenum

International Nuclear Information System (INIS)

Nielsen, C.H.

1977-06-01

Three field ion microscope (FIM) experiments were carried out to study the annealing behavior of heavy ion irradiated tungsten, tungsten (rhenium) alloys and molybdenum. The first experiment dealt with the stage I long-range migration of tungsten self interstitial atoms (SIAs) in high purity tungsten of resistivity ratio, R = 24,000 (R = rho 300 /rho 4 . 2 , where rho 300 and rho 4 . 2 are the room temperature and 0 0 C resistivities). The FIM specimens were irradiated in situ at 18 K with 30 keV W + ions to an average dose of 5 x 10 12 ions cm -2 and subsequently examined by the pulsed-field evaporation technique. The second experiment dealt with the phenomenon of impurity atom trapping of SIAs during long-range migration. It was shown that rhenium atoms in a tungsten matrix tend to capture tungsten SIAs and remain bound up to temperatures as high as 390 K. The final experiment was concerned with the low temperature annealing kinetics of irradiated molybdenum. High purity molybdenum of resistivity ratio R = 5700 was irradiated at 10 K with 30 keV Mo + ions to a dose of approximately 5 x 10 12 ions cm -2 . The results indicated that the electric field has only a minimal effect on the SIA annealing kinetics. This tends to strengthen the contention that the molybdenum SIA becomes mobile at 32 K

Rapid analysis of molybdenum contents in molybdenum master alloys by X-ray fluorescence technique

International Nuclear Information System (INIS)

Tongkong, P.

1985-01-01

Determination of molybdenum contents in molybdenum master alloy had been performed using energy dispersive x-ray fluorescence (EDX) technique where analysis were made via standard additions and calibration curves. Comparison of EDX technique with other analyzing techniques, i.e., wavelength dispersive x-ray fluorescence, neutron activation analysis and inductive coupled plasma spectrometry, showed consistency in the results. This technique was found to yield reliable results when molybdenum contents in master alloys were in the range of 13 to 50 percent using HPGe detector or proportional counter. When the required error was set at 1%, the minimum analyzing time was found to be 30 and 60 seconds for Fe-Mo master alloys with molybdenum content of 13.54 and 49.09 percent respectively. For Al-Mo master alloys, the minimum times required were 120 and 300 seconds with molybdenum content of 15.22 and 47.26 percent respectively

Method of producing oxidation resistant coatings for molybdenum

International Nuclear Information System (INIS)

Timmons, G.A.

1989-01-01

A method is described for producing a molybdenum element having adherently bonded thereto a thermally self-healing plasma-sprayed coating consisting essentially of a composite of molybdenum and a refactory oxide material capable of reacting with molybdenum oxide under oxidizing conditions to form a substantially thermally stable refractory compound of molybdenum, the method comprising plasma-spraying a coating formed by the step-wise application of a plurality of interbonded plasma-sprayed layers of a composite of molybdenum/refractory oxide material produced from a particulate mixture thereof. The coating comprises a first layer of molybdenum plasma-sprayed bonded to the substrate of the molybdenum element, a second layer of plasma-sprayed mixture of particulate molybdenum/refactory oxide consisting essentially of predominantly molybdenum bonded to the first layer, and succeeding layers of this mixture. The next step is heating the coated molybdenum element under oxidizing conditions to an elevated temperature sufficient to cause oxygen to diffuse into the surface of the multi-layered coating to react with dispersed molybdenum therein to form molybdenum oxide and effect healing of the coating by reaction of the molybdenum oxide with the contained refractory oxide and thereby protect the substrate of the molybdenum element against oxidation

Summary of the Preliminary Analysis of Savannah River Depleted Uranium Trioxide

International Nuclear Information System (INIS)

2010-01-01

This report summarizes a preliminary special analysis of the Savannah River Depleted Uranium Trioxide waste stream (SVRSURANIUM03, Revision 2). The analysis is considered preliminary because a final waste profile has not been submitted for review. The special analysis is performed to determine the acceptability of the waste stream for shallow land burial at the Area 5 Radioactive Waste Management Site (RWMS) at the Nevada National Security Site (NNSS). The Savannah River Depleted Uranium Trioxide waste stream requires a special analysis because the waste stream's sum of fractions exceeds one. The 99Tc activity concentration is 98 percent of the NNSS Waste Acceptance Criteria and the largest single contributor to the sum of fractions.

Molybdenum reduction to molybdenum blue in Serratia sp. Strain DRY5 is catalyzed by a novel molybdenum-reducing enzyme.

Science.gov (United States)

Shukor, M Y; Halmi, M I E; Rahman, M F A; Shamaan, N A; Syed, M A

2014-01-01

The first purification of the Mo-reducing enzyme from Serratia sp. strain DRY5 that is responsible for molybdenum reduction to molybdenum blue in the bacterium is reported. The monomeric enzyme has an apparent molecular weight of 105 kDalton. The isoelectric point of this enzyme was 7.55. The enzyme has an optimum pH of 6.0 and maximum activity between 25 and 35°C. The Mo-reducing enzyme was extremely sensitive to temperatures above 50°C (between 54 and 70°C). A plot of initial rates against substrate concentrations at 15 mM 12-MP registered a V max for NADH at 12.0 nmole Mo blue/min/mg protein. The apparent K m for NADH was 0.79 mM. At 5 mM NADH, the apparent V max and apparent K m values for 12-MP of 12.05 nmole/min/mg protein and 3.87 mM, respectively, were obtained. The catalytic efficiency (k cat/K m ) of the Mo-reducing enzyme was 5.47 M(-1) s(-1). The purification of this enzyme could probably help to solve the phenomenon of molybdenum reduction to molybdenum blue first reported in 1896 and would be useful for the understanding of the underlying mechanism in molybdenum bioremediation involving bioreduction.

Molybdenum Reduction to Molybdenum Blue in Serratia sp. Strain DRY5 Is Catalyzed by a Novel Molybdenum-Reducing Enzyme

Directory of Open Access Journals (Sweden)

M. Y. Shukor

2014-01-01

Full Text Available The first purification of the Mo-reducing enzyme from Serratia sp. strain DRY5 that is responsible for molybdenum reduction to molybdenum blue in the bacterium is reported. The monomeric enzyme has an apparent molecular weight of 105 kDalton. The isoelectric point of this enzyme was 7.55. The enzyme has an optimum pH of 6.0 and maximum activity between 25 and 35°C. The Mo-reducing enzyme was extremely sensitive to temperatures above 50°C (between 54 and 70°C. A plot of initial rates against substrate concentrations at 15 mM 12-MP registered a Vmax for NADH at 12.0 nmole Mo blue/min/mg protein. The apparent Km for NADH was 0.79 mM. At 5 mM NADH, the apparent Vmax and apparent Km values for 12-MP of 12.05 nmole/min/mg protein and 3.87 mM, respectively, were obtained. The catalytic efficiency (kcat/Km of the Mo-reducing enzyme was 5.47 M-1 s-1. The purification of this enzyme could probably help to solve the phenomenon of molybdenum reduction to molybdenum blue first reported in 1896 and would be useful for the understanding of the underlying mechanism in molybdenum bioremediation involving bioreduction.

Synthesis of vanadium trioxide

International Nuclear Information System (INIS)

Yankelevich, R.G.; Vinarov, I.V.; Sheka, I.A.; Pushek, N.G.

1976-01-01

There have been studied the conditions for production of vanadium trioxide in a single-stage process of V 2 O 5 reduction by gaseous ammonia. To determine the optimum conditions for V 2 O 5 reduction, there have been studied the temperature range of the reaction and the effect offered by the volumetric rate and time of ammonia injection. The following conditions have proved to be the optimum ones: temperature - 450 deg C, volumetric rate of NH 3 injection at a batch of 10 g - 4 l/h, time of recovery - 3 hours. In accordance with the adopted procedure there have been synthetized the samples containing 98 - 99% V 2 O 3 [ru

Simulation of uranium oxides reduction kinetics by hydrogen. Reactivities of germination and growth

International Nuclear Information System (INIS)

Brun, C.

1997-01-01

The aim of this work is to simulate the reduction by hydrogen of the tri-uranium octo-oxide U 3 O 8 (obtained by uranium trioxide calcination) into uranium dioxide. The kinetics curves have been obtained by thermal gravimetric analysis, the hydrogen and steam pressures being defined. The geometrical modeling which has allowed to explain the trend of the kinetics curves and of the velocity curves is an anisotropic germination-growth modeling. The powder is supposed to be formed of spherical grains with the same radius. The germs of the new UO 2 phase appear at the surface of the U 3 O 8 grains with a specific germination frequency. The growth reactivity is anisotropic and is very large in the tangential direction to the grains surface. Then, the uranium dioxide growths inside the grain and the limiting step is the grain surface. The variations of the growth reactivity and of the germination specific frequency in terms of the gases partial pressures and of the temperature have been explained by two different mechanisms. The limiting step of the growth mechanism is the desorption of water in the uranium dioxide surface. Concerning the germination mechanism the limiting step is a water desorption too but in the tri-uranium octo-oxide surface. The same geometrical modeling and the same germination and growth mechanisms have been applied to the reduction of a tri-uranium octo-oxide obtained by calcination of hydrated uranium trioxide. The values of the germination specific frequency of this solid are nevertheless weaker than those of the solid obtained by direct calcination of the uranium trioxide. (O.M.)

Method of producing molybdenum-99

Science.gov (United States)

Pitcher, Eric John

2013-05-28

Method of producing molybdenum-99, comprising accelerating ions by means of an accelerator; directing the ions onto a metal target so as to generate neutrons having an energy of greater than 10 MeV; directing the neutrons through a converter material comprising techentium-99 to produce a mixture comprising molybdenum-99; and, chemically extracting the molybdenum-99 from the mixture.

Cathodic electrodeposition of mixed molybdenum tungsten oxides from peroxo-polymolybdotungstate solutions.

Science.gov (United States)

Kondrachova, Lilia; Hahn, Benjamin P; Vijayaraghavan, Ganesh; Williams, Ryan D; Stevenson, Keith J

2006-12-05

Mixed molybdenum tungsten trioxide films of varying stoichiometry (MoxW1 - xO3, 0 cathodic electrodeposition on indium tin oxide (ITO)-coated glass substrates from aqueous peroxo-polymolybdotungstate solutions. Electrochemical quartz crystal microbalance (EQCM), cyclic voltammetry, and chronocoulometry were used to gain insight into the electrodeposition mechanism. The compositional and structural properties were characterized for MoxW1 - xO3 films deposited at intermediate potentials (-0.35 V vs Ag/AgCl) and sintered at 250 degrees C using energy-dispersive spectroscopy, X-ray diffraction, and Raman spectroscopy. These studies reveal that films consist of homogeneously mixed MoxW1 - xO3, with an enriched Mo content ranging in composition from 0.4 < x < 0.7 depending upon the mol % Mo present in the deposition solution. Chronoamperometry and spectroelectrochemical measurements were conducted to estimate lithium ion diffusion coefficients and coloration efficiencies for the mixed metal oxide films in 1 M LiClO4/propylene carbonate. The subtle interplay between structural and compositional properties due to the uniform mixing of Mo and W oxide components shows that electrochromic and lithium ion transport properties are moderately enhanced relative to those of single-component WO3 and MoO3 and demonstrate improved structural stability over pure MoO3 polymorphs during electrochemical cycling.

Molybdenum market in transition

International Nuclear Information System (INIS)

Sutulov, A.

1980-01-01

Since the beginning of 1980 - after seven years of constant unbalance between supply and demand of molybdenum, characterized by a demand overhang and after two years of unprecedented spot market prices - clear signals for a consolidation of the molybdenum market can be recognized. (orig.) [de

The Effect of Adding Antimony Trioxide (Sb2O3 ‎On A.C Electrical Properties of (PVA-PEG Films

Directory of Open Access Journals (Sweden)

Akeel Shakir Alkelaby

2017-12-01

Full Text Available In this work, many samples have been prepared by adding Antimony Trioxide (Sb2O3 to the polyvinyl alcohol-poly ethylene glycol (PVA-PEG. The effect of the Sb2O3 added as a filler with different weight percentages on the A.C electrical properties have been investigated. The samples were prepared as films by solution cast technique. The experimental results of the A.C electrical properties show that the dielectric constant increase with the increasing frequency of applied electrical field and concentration of the Antimony Trioxide. Dielectric loss decrease with the increasing the frequency, while it increases with the increase of the concentration of the Antimony Trioxide. The A.C electrical conductivity increase with increasing the Antimony Trioxide contain and frequency for the composition.

Primary defect production by high energy displacement cascades in molybdenum

Energy Technology Data Exchange (ETDEWEB)

Selby, Aaron P. [Department of Nuclear Engineering, University of Tennessee, Knoxville, TN 37996 (United States); Xu, Donghua, E-mail: xudh@utk.edu [Department of Nuclear Engineering, University of Tennessee, Knoxville, TN 37996 (United States); Juslin, Niklas; Capps, Nathan A. [Department of Nuclear Engineering, University of Tennessee, Knoxville, TN 37996 (United States); Wirth, Brian D. [Department of Nuclear Engineering, University of Tennessee, Knoxville, TN 37996 (United States); Oak Ridge National Laboratory, P.O. Box 2008, MS6003, Oak Ridge, TN 37831 (United States)

2013-06-15

We report molecular dynamics simulations of primary damage in molybdenum produced by high energy displacement cascades on the femto- to pico-second and Angstrom to nanometer scales. Clustering directly occurred for both interstitials and vacancies in the 1–50 keV cascade energy range explored. Point defect survival efficiency and partitioning probabilities into different sized clusters were quantified. The results will provide an important reference for kinetic models to describe the microstructural evolution in Mo under ion or neutron irradiations over much longer time and length scales.

Molybdenum Oxides - From Fundamentals to Functionality.

Science.gov (United States)

de Castro, Isabela Alves; Datta, Robi Shankar; Ou, Jian Zhen; Castellanos-Gomez, Andres; Sriram, Sharath; Daeneke, Torben; Kalantar-Zadeh, Kourosh

2017-10-01

The properties and applications of molybdenum oxides are reviewed in depth. Molybdenum is found in various oxide stoichiometries, which have been employed for different high-value research and commercial applications. The great chemical and physical characteristics of molybdenum oxides make them versatile and highly tunable for incorporation in optical, electronic, catalytic, bio, and energy systems. Variations in the oxidation states allow manipulation of the crystal structure, morphology, oxygen vacancies, and dopants, to control and engineer electronic states. Despite this overwhelming functionality and potential, a definitive resource on molybdenum oxide is still unavailable. The aim here is to provide such a resource, while presenting an insightful outlook into future prospective applications for molybdenum oxides. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Studying arsenic trioxide-induced apoptosis of Colo-16 cells with ...

African Journals Online (AJOL)

Jane

2011-10-05

Oct 5, 2011 ... induced apoptosis at the single cell level. Key words: Two-photon laser scanning microscopy, confocal laser scanning microscopy, human skin squamous carcinoma cells (Colo-16 cells), arsenic trioxide, apoptosis. INTRODUCTION. Although arsenic is poisonous and chronic arsenic exposure from ...

Color in 'tungsten trioxide' thin films

International Nuclear Information System (INIS)

Gerard, P.; Deneuville, A.; Hollinger, G.; Duc, Tran Minh

1977-01-01

We show that evaporated tungsten trioxide amorphous layers commonly used in electrochromic displays actually have the composition WO_2_._7H_y (0.2< y<0.5). We emphasize that coloration of virgin transparent films can be obtained without injection of any external ion into the layer, and further that around a critical substoichiometry by sputtering, namely, WO_2_._5, one can prepare blue virgin layers without any hydrogen. The effect of substoichiometry on the valence of tungsten atoms has been followed by XPS measurements of sputtered layers.

Color in ''tungsten trioxide'' thin films

International Nuclear Information System (INIS)

Gerard, P.; Deneuville, A.; Hollinger, G.; Tran Minh Duc

1977-01-01

We show that evaporated tungsten trioxide amorphous layers commonly used in electrochromic displays actually have the composition WO/sub 2.7/H/sub y/ (0.2< y<0.5). We emphasize that coloration of virgin transparent films can be obtained without injection of any external ion into the layer, and further that around a critical substoichiometry by sputtering, namely, WO/sub 2.5/, one can prepare blue virgin layers without any hydrogen. The effect of substoichiometry on the valence of tungsten atoms has been followed by XPS measurements of sputtered layers

Determination of antimony trioxide in fire-retardant conveyor belts

Energy Technology Data Exchange (ETDEWEB)

Rytych-Witwicka, B.; Szmyd, E.

1976-12-01

Two methods for the determination of antimony trioxide in rubber and pvc are described. One is a colorimetric method based on the reaction of antimony with rhodamine B; the other is a polarographic method. The results of the two methods show a satisfactory consistency and the methods themselves appear rapid and effective.

Elimination of excess molybdenum by cattle

Energy Technology Data Exchange (ETDEWEB)

Toelgyesi, G.; Elmoty, I.A.

1967-01-01

It was found that cattle would ingest spontaneously 5-15 g of molybdenum on one occasion. The uptake of this quantity caused but moderate loss of appetite and mild enteritis, both normalizing in one week. The occurrence of a severe acute molybdenum poisoning can be practically excluded, owing to refusal of the poisoned feed. Spontaneously ingested molybdenum caused on the first day a 30-100 fold rise of ruminal Mo-level, decreasing to the order of the normal value in about one week. But in the urine and faeces, Mo-level was at least 10 fold, in the blood and milk about 4 fold of the normal one, even one or two weeks after ingestion. During this period at least 90% of ingested Mo was eliminated with the faeces, urine and milk. One week after the ingestion of molybdenum, the rumen content showed no evidence on poisoning and no trace of molybdenum. Oral administration of ammonium molybdenate in an amount equivalent to 40 g molybdenum caused no fatality. In fact, cattle would never ingest spontaneously such a large dose.

Static recrystallisation and precipitation after hot deformation of austenitic stainless steels containing molybdenum and niobium

International Nuclear Information System (INIS)

Lombry, R.; Rossard, C.; Thomas, B.J.

1981-01-01

In general the hot workability of austenite depends on the work hardening during deformation and the kinetics of the dynamic and static restoration processes. Static recrystallisation is a very important factor in the case of hot rolling. The present work was undertaken to determine the effect of additions of molybdenum or niobium on the kinetics of static recrystallisation. The results show that the rate of static recrystallisation of type 304, 316 and 347 stainless steels decreases in this order for a given amount of prior deformation (epsilon=0,44). The differences in the rates of recrystallisation increases as the temperature is lowered towards 900 deg C. The effect of molybdenum appears to be attribuable to a solute drag effect on the mobility of dislocations, subgrain boundaries or grain boundaries whereas niobium additions lead to the formation of NbC precipitates on the dislocation cell walls and sub boundaries. It is also shown that in the case of type 316 and type 347 steels the dynamic recrystallisation process (observed in type 304 steels at all temperatures above 900 deg C) is replaced by dynamic recovery at temperatures egal to or below about 1000 deg C [fr

Molybdenum solubility in aluminium nitrate solutions

Energy Technology Data Exchange (ETDEWEB)

Heres, X.; Sans, D.; Bertrand, M.; Eysseric, C. [CEA, Centre de Marcoule, Nuclear Energy Division, DRCP, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Brackx, E.; Domenger, R.; Excoffier, E. [CEA, Centre de Marcoule, Nuclear Energy Division, DTEC, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Valery, J.F. [AREVA-NC, DOR/RDP, Paris - La Defense (France)

2016-07-01

For over 60 years, research reactors (RR or RTR for research testing reactors) have been used as neutron sources for research, radioisotope production ({sup 99}Mo/{sup 99m}Tc), nuclear medicine, materials characterization, etc... Currently, over 240 of these reactors are in operation in 56 countries. They are simpler than power reactors and operate at lower temperature (cooled to below 100 C. degrees). The fuel assemblies are typically plates or cylinders of uranium alloy and aluminium (U-Al) coated with pure aluminium. These fuels can be processed in AREVA La Hague plant after batch dissolution in concentrated nitric acid and mixing with UOX fuel streams. The aim of this study is to accurately measure the solubility of molybdenum in nitric acid solution containing high concentrations of aluminium. The higher the molybdenum solubility is, the more flexible reprocessing operations are, especially when the spent fuels contain high amounts of molybdenum. To be most representative of the dissolution process, uranium-molybdenum alloy and molybdenum metal powder were dissolved in solutions of aluminium nitrate at the nominal dissolution temperature. The experiments showed complete dissolution of metallic elements after 30 minutes long stirring, even if molybdenum metal was added in excess. After an induction period, a slow precipitation of molybdic acid occurs for about 15 hours. The data obtained show the molybdenum solubility decreases with increasing aluminium concentration. The solubility law follows an exponential relation around 40 g/L of aluminium with a high determination coefficient. Molybdenum solubility is not impacted by the presence of gadolinium, or by an increasing concentration of uranium. (authors)

Chemical Fixation of CO{sub 2} to Acrylates Using Low-Valent Molybdenum Sources

Energy Technology Data Exchange (ETDEWEB)

Bernskoetter, Wesley

2013-09-30

The kinetic, mechanistic, and reactivity experiments to access the viability and possible reaction design of coupling of carbon dioxide and ethylene at a zerovalent molybdenum for the production of acrylates are described. A general model of the reaction mechanism has been outlined, including assessment of the rate limiting step in the reaction. Kinetic and computational data have valuated the influence of a range of tridentate ligand platforms on the rate of coupling. An in situ reduction and acrylate formation activity screen protocol has also been developed to aid in the technology development of this process. Portions of descriptions of the research products presented here have also been adapted with permission from journal publications.

Influence of the mode of preparation of the UO3 trioxide on its specific surface

International Nuclear Information System (INIS)

Sauteron, J.

1960-01-01

As the specific surface of uranium trioxide UO 3 closely depends on the preparation mode and conditions, the authors report and discuss several results obtained on uranium trioxides produced either by precipitation of uranyl nitrate (with oxygenated water, liquid or gaseous ammoniac, and ammonium carbonate), then by calcination at 350 C, or by thermal decomposition of the uranyl nitrate. The authors also studied the influence of calcination temperature of ammonium uranate on the specific surface of the obtained oxide (between 200 and 900 deg.) [fr

Standard Method for Analyzing Gases in Titanium and Titanium Alloys. Standard Method for the Chemical Analysis of Titanium Alloys.

Science.gov (United States)

1982-10-28

form a non- soluble complex. After filtering and burning the non-pure molybdenum trioxide is weighed. Ammonia water is used to dissolve the molybdenum...niobium and tantalum should use the methyl alcohol distillation - curcumin absorption luminosity 66 method for determination. II. The Methyl Alcohol...Distillation - Curcumin Absorption Luminosity Method 1. Summary of Method In a phosphorus sulfate medium, boron and methyl alcohol produce methyl borate

Enhancement of efficiencies for tandem green phosphorescent organic light-emitting devices with a p-type charge generation layer

Energy Technology Data Exchange (ETDEWEB)

Yoo, Byung Soo; Jeon, Young Pyo; Lee, Dae Uk; Kim, Tae Whan, E-mail: twk@hanayng.ac.kr

2014-10-15

The operating voltage of the tandem green phosphorescent organic light-emitting device with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer was improved by 3% over that of the organic light-emitting device with a molybdenum trioxide layer. The maximum brightness of the tandem green phosphorescent organic light-emitting device at 21.9 V was 26,540 cd/m{sup 2}. The dominant peak of the electroluminescence spectra for the devices was related to the fac-tris(2-phenylpyridine) iridium emission. - Highlights: • Tandem OLEDs with CGL were fabricated to enhance their efficiency. • The operating voltage of the tandem OLED with a HAT-CN layer was improved by 3%. • The efficiency and brightness of the tandem OLED were 13.9 cd/A and 26,540 cd/m{sup 2}. • Efficiency of the OLED with a HAT-CN layer was lower than that with a MoO{sub 3} layer. - Abstract: Tandem green phosphorescent organic light-emitting devices with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile or a molybdenum trioxide charge generation layer were fabricated to enhance their efficiency. Current density–voltage curves showed that the operating voltage of the tandem green phosphorescent organic light-emitting device with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer was improved by 3% over that of the corresponding organic light-emitting device with a molybdenum trioxide layer. The efficiency and the brightness of the tandem green phosphorescent organic light-emitting device were 13.9 cd/A and 26,540 cd/m{sup 2}, respectively. The current efficiency of the tandem green phosphorescent organic light-emitting device with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer was lower by 1.1 times compared to that of the corresponding organic light-emitting device with molybdenum trioxide layer due to the decreased charge generation and transport in the 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer resulting from triplet–triplet exciton annihilation.

CVD molybdenum films of high infrared reflectance

Energy Technology Data Exchange (ETDEWEB)

Carver, G. E.

1979-01-01

Molybdenum thin films of high infrared reflectance have been deposited by pyrolytic decomposition of molybdenum carbonyl (Mo(CO)/sub 6/), and by hydrogen reduction of molybdenum pentachloride (MoCl/sub 5/). Reflectance values within 0.7% of the reflectance of supersmooth bulk molybdenum have been attained by annealing films of lower reflectance in both reducing and non-reducing atmospheres. All depositions and anneals proceed at atmospheric pressure, facilitating a continuous, flow-through fabrication. These reflectors combine the high temperature stability of molybdenum thin films with the infrared reflectance of a material such as aluminum. Deposition from Mo(CO)/sub 6/ under oxidizing conditions, and subsequent anneal in a reducing atmosphere, results in films that combine high solar absorptance with low thermal emittance. If anti-reflected, black molybdenum films can serve as highly selective single layer photothermal converters. Structural, compositional, and crystallographic properties have been measured after both deposition and anneal.

Evaluation of magnetite nanoparticles as molybdenum ions adsorbent

International Nuclear Information System (INIS)

Holland, Helber; Yamaura, Mitiko; Sousa, Jose Silva; Freitas, Antonio Alves

2011-01-01

Molybdenum-99 is the generator radionuclide of the most used radioisotope for preparation of radiopharmaceuticals with diagnostic purposes in nuclear medicine, technetium-99m (Tc-99m). One way of Mo-99 obtaining is as fission product of irradiated uranium targets in reactor. In this work, the potential application of magnetite particles in the separation of Mo-99 from a dissolution solution of U targets was evaluated. Synthetic magnetite nanoparticles were prepared by alkaline precipitation method from Fe 2+ ions and heat-treated via microwave irradiation in a conventional household oven. Adsorption kinetics was studied. It was observed that the adsorption of Mo by magnetite nanoparticles is fast and followed the model of pseudo-second order. (author)

Organic transformations catalyzed by methylrhenium trioxide

Energy Technology Data Exchange (ETDEWEB)

Zhu, Zuolin [Iowa State Univ., Ames, IA (United States)

1995-10-06

Methylrhenium trioxide (MTO), CH₃ReO₃, was first prepared in 1979. MTO forms stable or unstable adducts with electron-rich ligands, such as amines (quinuclidine, 1,4-diazabicyclo-octane, pyridine, aniline, 2,2'-bipyridine), alkynes, olefins, 1,2-diols, catechols, hydrogen peroxide, water, thiophenols, 1,2-dithiols, triphenylphosphine, 2-aminophenols, 2-aminothiophenols, 8-hydroxyquinoline and halides (Cl-, Br-, I-). After coordination, different further reactions will occur for different reagents. Reactions described in this report include the dehydration of alcohols, direct amination of alcohols, activation of hydrogen peroxide, oxygen transfer, and decomposition of ethyl diazoacetate.

Preparation of selective molybdenum concentrate from collective coppermolybdenum concentrate

Directory of Open Access Journals (Sweden)

N. Tusupbaev

2016-06-01

Full Text Available The paper considers possibilities of selective separation of the concentrate of copper and molybdenum from a collective copper-molybdenum concentrate of Aktogay deposit using regrinding and conventional flotation reagents. In the case of conventional flotoreagents, the content of molybdenum in a molybdenum concentrate was 8.0% at extraction effectiveness 83.12%. At 27.96% extraction degree of copper, it’s content in the concentrate equaled to 21.3%. After regrinding, molybdenum content in the concentrate was 24.0% at the extraction effectiveness 59.63%, and copper content in the concentrate was 21.9% at the recovery of 61.23%. Thus, the regrinding of a collective copper-molybdenum concentrate resulted in an increase in the content of molybdenum in molybdenum concentrate by 16%, and the copper concentration increased by 0.6%.

The Development of Molybdenum Speciation as a Paleoredox Tool

Science.gov (United States)

Rodley, J.; Peacock, C.; Mosselmans, J. F. W.; Poulton, S.

2017-12-01

The redox state of the oceans has changed throughout geological time and an understanding of these changes is essential to elucidate links between ocean chemistry, climate and life. Due to its abundance in seawater and redox-sensitive nature, molybdenum has enormous potential as a paleoredox proxy. Although a significant amount of research has been done on molybdenum in ancient and modern sediments in terms of its concentrations and isotopic ratios there remains a limited understanding of the drawdown mechanisms of molybdenum under different redox conditions restricting its use in identifying a range of redox states. In order to address these uncertainties, we have developed a novel sequential extraction technique to examine molybdenum concentrations in six sediment fractions from modern samples that represent oxic, nitrogenous, ferruginous and euxinic environments. In addition we use µ-XRF and µ-XANES synchrotron spectroscopy to examine the molybdenum speciation within these fractions and environments. To interpret our µ-XANES data we have developed an extensive library of molybdenum XANES standards that represent molybdenum sequestration by the sediment fractions identified from the sequential extraction. To further verify our synchrotron results we developed a series of µ-XANES micro-column experiments to examine preferential uptake pathways of molybdenum to different sediment phases under a euxinic water column. The initial data from both the sequential extraction and µ-XANES methods indicate that molybdenum is not limited to a single burial pathway in any of the redox environments. We find that each of the redox environments can be characterised by a limited set of molybdenum phase associations, with molybdenum adsorption to pyrite likely the dominant burial pathway. These findings agree with existing research for molybdenum speciation in euxinic environments suggesting that both pyrite and sulphidised organic matter act as important molybdenum sinks. Our

Molybdenum distribution and sensitivity in tomatoes, sunflowers and beans

Energy Technology Data Exchange (ETDEWEB)

Hecht-Buchholz, C

1973-01-01

The influence of increasing levels of molybdenum on the growth, molybdenum uptake and distribution in individual plant organs was investigated in tomatoes, beans and sunflowers in a 9 day trial. With tomatoes, which showed marked damage with high molybdenum levels, the molybdenum content of dry matter was highest in the leaf and lowest in the stem. On the other hand, beans, insensitive towards the high molybdenum level, dry matter molybdenum content was appreciably higher in the stem than in the leaf. It is supposed that in plant species, insensitive to high molybdenum levels, molybdenum is held less firmly in this tissue and can attain damaging levels in the cytoplasm of the youngest leaf tissue cells. It is supposed, on the basis of the reactions which were carried out with expressed root juice and on the basis of the yellow coloration attainable in vitro in the tissue caused by the addition of molybdate solution, that the yellow coloration appearing in the cells and plant organs of various plant species, here tomatoes and sunflowers, with high molybdenum levels is due to a reaction between molybdenum and polyvalent phenols in cellsap.

Success Rate of Formocresol Pulpotomy versus Mineral Trioxide Aggregate in Human Primary Molar Tooth

Directory of Open Access Journals (Sweden)

S E Jabbarifar

2004-12-01

Full Text Available Background: In spite of long time and broad use of formaldehyde derivates (Fixation agent in primary tooth pulp treatment, There is some concerns about these derivates such as variability, inconsistency success rate, mutagenicity, cytotoxicity, alergenicity, and some other potential health hazards of them. Therefore other alternative pulpotomy procedures like Bioactive glass (BAG, Glutaraldehyde (2%, Hydroxyappetite (HA, Bone dried freezed (BDF, ferric sulfate (15%, laser, Electrosurgery (ES, Bone Morphogenic proteins (BMP, recombinant protein-1 (RP1, and Mineral Trioxide Aggregate (MTA have been compared. The purpose of this clinical trial is to assess radiographic and clinical success rate of Formocresol (FC pulpotomy in compare with MTA in human primary molar teeth. Methods: 64 molars were pulpotomized equally and randomly with mineral trioxide Aggregate and Formocresol. Prior to trial, we defined a case as failure, when one or more of the events such as external root resorption, internal root resorption, periapical and furca lucency, pain, swelling, mobility, dental abscess, or early extraction appeared. Every treated tooth was defined as successful, if any noted evident was not shown. Results: Totally, 60 teeth treatment (92.2 percent were successful and 7.8 percent were failed. Failure and success rates for MTA group were 6.3 and 93.7 percent, respectively. Failure and success rates in FC group were 8.4 and 90.2 percent respectively. The difference between MTA and FC treatment methods was not significant (Fisher Exact test. Conclusion: Findings of this study show that mineral trioxide aggregate can be an alternative procedure for FC pulpotomy of primary tooth. Keywords: Mineral trioxide aggregate, formocresol, pulpotomy, success and failure rate.

The corrosion behavior of molybdenum and Hastelloy B in sulfur and sodium polysulfides at 623 K

International Nuclear Information System (INIS)

Brown, A.P.

1987-01-01

An experimental study was completed to determine the corrosion behavior of molybdenum and Hastelloy B, a nickel-based alloy with high molybdenum content, in sulfur and sodium polysulfides (Na/sub 2/S/sub 3/,Na/sub 2/S/sub 4/, Na/sub 2/S/sub 5/) at 623 K. In sulfur, molybdenum corrodes very slowly, with a parabolic rate constant of 3.6 x 10/sup -9/ cm s/sup -1/2/. Hastelloy B shows no measurable corrosion after 100h of exposure to sulfur. The corrosion reaction of molybdenum in Na/sub 2/S/sub 3/ is characterized by the formation of a protective film that effectively eliminates further corrosion after the first 100h of exposure. Hastelloy B, however, corrodes rapidly in Na/sub 2/S/sub 3/, with corrosion rates approaching those of pure nickel under the same conditions. After the first 4h of exposure, the kinetics for the corrosion of Hastelloy B in Na/sub 2/S/sub 3/ follows a linear rate law. The scale morphology has multiple spalled layers of NiS/sub 2/, with some crystallites of NiS/sub 2/ appearing on the leading face of the scale and between the individual scale layers. This spalling causes smaller coupons of the Hastelloy B to corrode faster than larger coupons

Behavior of molybdenum in mixed-oxide fuel

International Nuclear Information System (INIS)

Giacchetti, G.; Sari, C.

1976-01-01

Metallic molybdenum, Mo--Ru--Rh--Pd alloys, barium, zirconium, and tungsten were added to uranium and uranium--plutonium oxides by coprecipitation and mechanical mixture techniques. This material was treated in a thermal gradient similar to that existing in fuel during irradiation to study the behavior of molybdenum in an oxide matrix as a function of the O/(U + Pu) ratio and some added elements. Result of ceramographic and microprobe analysis shows that when the overall O/(U + Pu) ratio is less than 2, molybdenum and Mo--Ru--Rh--Pd alloy inclusions are present in the uranium--plutonium oxide matrix. If the O/(U + Pu) ratio is greater than 2, molybdenum oxidizes to MoO 2 , which is gaseous at a temperature approximately 1000 0 C. Molybdenum oxide vapor reacts with barium oxide and forms a compound that exists as a liquid phase in the columnar grain region. Molybdenum oxide also reacts with tungsten oxide (tungsten is often present as an impurity in the fuel) and forms a compound that contains approximately 40 wt percent of actinide metals. The apparent solubility of molybdenum in uranium and uranium--plutonium oxides, determined by electron microprobe, was found to be less than 250 ppM both for hypo- and hyperstoichiometric fuels

Isotope analysis of molybdenum in selected minerals

International Nuclear Information System (INIS)

Becker, S.; Dietze, H.J.

1980-01-01

An analytical method is described for the mass spectrometric determination of molybdenum abundance values. The results of analyses of three molybdenum mineral samples are presented and compared with the results of other authors. It is shown that the fine variations of molybdenum in natural minerals cannot be analysed with currently available mass spectrometers

Structural, morphological, gas sensing and photocatalytic characterization of MoO3 and WO3 thin films prepared by the thermal vacuum evaporation technique

Science.gov (United States)

Arfaoui, A.; Touihri, S.; Mhamdi, A.; Labidi, A.; Manoubi, T.

2015-12-01

Thin films of molybdenum trioxide and tungsten trioxide were deposited on glass substrates using a simplified thermal evaporation under vacuum method monitored by heat treatment in flowing oxygen at 500 °C for 1 h. The structural and morphological properties of the films were investigated using X-ray diffraction, Raman spectroscopy, atomic force microscopy and scanning electron microscopy. The X-ray diffraction analysis shows that the films of MoO3 and WO3 were well crystallized in orthorhombic and monoclinic phase respectively with the crystallites preferentially oriented toward (2 0 0) direction parallel a-axis for both samples. In literature, we have shown in previous papers that structural and surface morphology of metal thin films play an important role in the gas detection mechanism. In this article, we have studied the response evolution of MoO3 and WO3 thin films sensors ethanol versus time, working temperature and the concentration of the ethanol. It was found that these films had high sensitivity to ethanol, which made them as a good candidate for the ethanol sensor. Finally, the photocatalytic activity of the samples was evaluated with respect to the degradation reaction of a wastewater containing methylene blue (MB) under UV-visible light irradiation. The molybdenum trioxide exhibits a higher degradation rate than the tungsten trioxide thin films under similar experimental conditions.

Kinetics and mechanism of the oxidation of alkenes and silanes by hydrogen peroxide catalyzed by methylrhenium trioxide (MTO) and a novel application of electrospray mass spectrometry to study the hydrolysis of MTO

Energy Technology Data Exchange (ETDEWEB)

Tan, Haisong [Iowa State Univ., Ames, IA (United States)

1999-11-08

Conjugated dienes were oxidized by hydrogen peroxide with methylrhenium trioxide (MTO) as catalyst. Methylrhenium bis-peroxide was the major reactive catalyst present. Hydroxyalkenes and trisubstituted silane were also tested. Mechanisms for each of these reactions are presented.

Crevice corrosion kinetics of nickel alloys bearing chromium and molybdenum

International Nuclear Information System (INIS)

Zadorozne, N.S.; Giordano, C.M.; Rodríguez, M.A.; Carranza, R.M.; Rebak, R.B.

2012-01-01

Highlights: ► The crevice corrosion resistance of the tested alloys increased with PREN, which is mainly affected by their Mo content. ► Crevice corrosion kinetics was controlled by ohmic drop only in the more dilute chloride solutions. ► Charge transfer control was observed in concentrated chloride solutions. ► A critical ohmic drop was not necessary for crevice corrosion to occur. ► Ohmic drop was a consequence of the crevice corrosion process in certain conditions. - Abstract: The crevice corrosion kinetics of alloys C-22, C-22HS and HYBRID-BC1 was studied in several chloride solutions at 90 °C. The crevice corrosion resistance of the alloys increased with PREN (Pitting Resistance Equivalent Number), which is mainly affected by the Mo content in the alloys. The crevice corrosion kinetics of the three alloys was analyzed at potentials slightly higher than the repassivation potential. Crevice propagation was controlled by ohmic drop in the more dilute chloride solutions, and by charge transfer in the more concentrated chloride solutions. Ohmic drop was not a necessary condition for crevice corrosion to occur.

Preparation of molybdenum oxide thin films by MOCVD

International Nuclear Information System (INIS)

Guerrero, R. Martinez; Garcia, J.R. Vargas; Santes, V.; Gomez, E.

2007-01-01

In this study, molybdenum oxide films were prepared in a horizontal hot-wall MOCVD apparatus using molybdenum dioxide acetylacetonate as precursor. The molybdenum precursor was synthesized from acetylacetone and molybdenum oxide powder. Thermal gravimetric (TG) and differential thermal analyses (DTA) of the precursor suggested the formation of molybdenum oxides around 430 o C (703 K). Thus, a range of deposition temperatures varying from 350 to 630 o C (623-903 K) was explored to investigate the effects on the nature of the molybdenum oxide films. X-ray diffraction (XRD) results showed that the films consisted of α-MoO 3 phase at deposition temperatures ranging from 400 to 560 o C (673-833 K). Crystalline α-MoO 3 films can be obtained from molybdenum dioxide acetylacetonate precursor, without need of a post-annealing treatment. The best crystalline quality was found in films having needle-like crystallites grown at deposition temperature of about 560 o C (833 K), which exhibit a strong (0 1 0) preferred orientation and a transparent visual appearance

Preparation of molybdenum oxide thin films by MOCVD

Energy Technology Data Exchange (ETDEWEB)

Guerrero, R. Martinez [Depto. de Ingenieria Metalurgica, ESIQIE-IPN, Mexico 07300, D.F. (Mexico); Garcia, J.R. Vargas [Depto. de Ingenieria Metalurgica, ESIQIE-IPN, Mexico 07300, D.F. (Mexico)]. E-mail: rvargasga@ipn.mx; Santes, V. [CIIEMAD-IPN, Miguel Othon de Mendizabal 485, Mexico 07700, D.F. (Mexico); Gomez, E. [Instituto de Quimica-UNAM, Circuito Exterior-Ciudad Universitaria, Mexico 04510, D.F. (Mexico)

2007-05-31

In this study, molybdenum oxide films were prepared in a horizontal hot-wall MOCVD apparatus using molybdenum dioxide acetylacetonate as precursor. The molybdenum precursor was synthesized from acetylacetone and molybdenum oxide powder. Thermal gravimetric (TG) and differential thermal analyses (DTA) of the precursor suggested the formation of molybdenum oxides around 430 {sup o}C (703 K). Thus, a range of deposition temperatures varying from 350 to 630 {sup o}C (623-903 K) was explored to investigate the effects on the nature of the molybdenum oxide films. X-ray diffraction (XRD) results showed that the films consisted of {alpha}-MoO{sub 3} phase at deposition temperatures ranging from 400 to 560 {sup o}C (673-833 K). Crystalline {alpha}-MoO{sub 3} films can be obtained from molybdenum dioxide acetylacetonate precursor, without need of a post-annealing treatment. The best crystalline quality was found in films having needle-like crystallites grown at deposition temperature of about 560 {sup o}C (833 K), which exhibit a strong (0 1 0) preferred orientation and a transparent visual appearance.

Nitrogen reduction: Molybdenum does it again

Science.gov (United States)

Schrock, Richard R.

2011-02-01

Nature reduces dinitrogen under mild conditions using nitrogenases, the most active of which contains molybdenum and iron. The only abiological dinitrogen reduction catalyst that avoids the harsh conditions of the Haber-Bosch process contains just molybdenum.

Molybdenum sealing glass-ceramic composition

International Nuclear Information System (INIS)

Eagan, R.J.

1976-01-01

A glass-ceramic composition is described having low hydrogen and helium permeability properties, along with high fracture strength, and a thermal coefficient of expansion similar to that of molybdenum. The composition is adaptable for hermetically sealing to molybdenum at temperatures between 900 and about 950 0 C to form a hermetically sealed insulator body

Development of Silicide Coating on Molybdenum Alloy Cladding

International Nuclear Information System (INIS)

Lim, Woojin; Ryu, Ho Jin

2015-01-01

The molybdenum alloy is considered as one of the accident tolerant fuel (ATF) cladding materials due to its high temperature mechanical properties. However, molybdenum has a weak oxidation resistance at elevated temperatures. To modify the oxidation resistance of molybdenum cladding, silicide coating on the cladding is considered. Molybdenum silicide layers are oxidized to SiO 2 in an oxidation atmosphere. The SiO 2 protective layer isolates the substrate from the oxidizing atmosphere. Pack cementation deposition technique is widely adopted for silicide coating for molybdenum alloys due to its simple procedure, homogeneous coating quality and chemical compatibility. In this study, the pack cementation method was conducted to develop molybdenum silicide layers on molybdenum alloys. It was found that the Mo 3 Si layer was deposited on substrate instead of MoSi 2 because of short holding time. It means that through the extension of holding time, MoSi 2 layer can be formed on molybdenum substrate to enhance the oxidation resistance of molybdenum. The accident tolerant fuel (ATF) concept is to delay the process following an accident by reducing the oxidation rate at high temperatures and to delay swelling and rupture of fuel claddings. The current research for Atf can be categorized into three groups: First, modification of existing zirconium-based alloy cladding by improving the high temperature oxidation resistance and strength. Second, replacing Zirconium based alloys with alternative metallic materials such as refractory elements with high temperature oxidation resistance and strength. Third, designing alternative fuel structures using ceramic and composite systems

High strength tungsten heavy alloys with molybdenum additions

International Nuclear Information System (INIS)

Bose, A.; Sims, D.M.; German, R.M.

1987-01-01

Tungsten heavy alloys are candidates for numerous applications based on the unique combination of high density, high strength, and high ductility coupled with excellent machinability. Though there has been considerable research on heavy alloys, the primary focus has been on the ductility. These alloys are well suited for ballistic uses due to their high densities and it is expected that for superior ballistic performance, a high hardness, high strength and moderate ductility alloy would be ideal. The major goal of this investigation was to obtain heavy alloys with hardness greater than HRA 72. It is evident from the phase diagrams that molybdenum, which goes into solution in tungsten, nickel and iron, could act as a potential strengthening addition. With this in view, tungsten heavy alloys with molybdenum additions were fabricated from mixed elemental powders. A baseline composition of 90W-7Ni-3Fe was chosen to its good elongation and moderate strength. The molybdenum additions were made by replacing the tungsten. Compared to the baseline properties with no molybdenum addition, the strength and hardness showed a continuous increase with molybdenum addition. The ductility of the alloy continued to decrease with increasing molybdenum content, but even with 16% wt. % molybdenum of the elongation was still around 6%. An interesting facet of these alloying additions is the grain refinement that is brought about by adding to molybdenum to the system. The grain refinement is related to the lower solubility of tunbsten in the matrix due to partial displacement by molybdenum

Antimony Trioxide (ATO) - Summary of External Peer Review and Public Comments and Disposition

Science.gov (United States)

This document summarizes the public and external peer review comments that the EPA’s Office of Pollution Prevention and Toxics (OPPT) received for the draft work plan risk assessment for Antimony Trioxide (ATO).

Scale-up of heterogeneous catalytic reactions

Energy Technology Data Exchange (ETDEWEB)

Heggs, P; Sunderland, P

1979-12-01

This report on the Institution of Chemical Engineers ''Problems in Applied Catalysis'' Meeting (Bath, U.K. 1/4-5/78) covers papers on the nature of the catalyst surface, including the use of IR spectroscopy, electron energy loss spectroscopy, low-energy electron diffraction, electron spectroscopy, secondary ion mass spectroscopy, and modular-beam scattering for investigating solid surfaces and their relevance to catalysis; study of the reaction mechanisms by which catalysis takes place; use of mechanistic models to determine the true chemical kinetics illustrated for the oxidation of benzene to maleic anhydride over a vanadium pentoxide/molybdenum trioxide catalyst; the study with respect to the importance of transport effects in catalyst pellets on scale-up, falsification of true kinetics, and the design of laboratory reactors; full-scale reactor design of packed-bed reactors; and practical scale-up problems illustrated for methanol synthesis over a copper catalyst, ammonia oxidation over a cobalt oxide catalyst, and the steam reforming of naphtha.

Electric heating of a unit for uranium trioxide production

International Nuclear Information System (INIS)

Faron, R.; Striff, A.

1985-01-01

Ammonium diuranate U 2 O 7 (NH 4 ) 2 containing about 50% of water is dried and transformed by calcination in uranium trioxide UO 3 . Drying and calcination was obtained by air heated by two burners using domestic fuel. In 1984 the plant was transformed for utilization of electric heating improving maintenance cost, decreasing heat losses and by energy saving the payback period on investment is of 2.6 years [fr

Process for separation of tungsten and molybdenum by extraction

International Nuclear Information System (INIS)

Zelikman, A.N.; Voldman, G.M.; Rumyantsev, V.K.; Ziberov, G.N.; Kagermanian, V.S.

1976-01-01

A process for the separation of tungsten and molybdenum by extraction involves the addition of HCl or HNO 3 to an aqueous solution containing tungsten and molybdenum to obtain a pH from 0.5 to 4.3, and introduction of a stabilizer comprising water-soluble phosphorus salts and a complexing agent, hydrogen peroxide, in an amount from 1.5 to 2 mole per 1 g-atom of the total content of tungsten and molybdenum. Then molybdenum is selectively extracted from the resulting aqueous solution with tri-n-butylphosphate with equal volumetric proportioning of the aqueous and organic solutions. Re-extraction of molybdenum and partially tungsten is carried out from the organic extracting agent with an alkali or soda solution. The process makes possible the preparation of tungsten solution containing no more than 0.001 g/l of molybdenum, and an increase in the degree of extraction of tungsten and molybdenum

On mechanism of austenite chromium-nickel-molybdenum steels intercrystalline corrosion in weak and strong oxidizing media

International Nuclear Information System (INIS)

Plaskeev, A.V.; Savkina, L.Ya.; Knyazheva, V.M.; Kolotyrkin, Ya.M.; Fil'dgandler, Eh.G.; Rodin, N.N.

1975-01-01

Wide possibilities γ-spectrometry for kinetic investigation of intercrystalline corrosion (ICC) and also for recognizing the nature of the selectively soluble structural components at the stages of their initiation and development has been determined using 00Cr16Ni15Mo steel, containing 0,05 and 0,03%C. It is shown by γ-spectrometry, autoradiography, electrochemistry, optical and electron metallography in combination with (Cr,Fe,Mo) 23 C 6 carbide properties investigation, that ICC of sensitized 00Cr16Ni15Mo3 steel, is determined by selective dissolution of chromium and molybdenum depleted boundary regions of solid solutions. At potentials of passivation region (imitation of D method) the main cause of ICC is the selective dissolution of (Cr;Fe;Mo) 23 C 6 carbides arranged at grain boundaries. This process is facilitated in the presence of molybdenum in carbide

Formation of self-ordered porous anodized alumina template for growing tungsten trioxide nanowires

Science.gov (United States)

Hussain, Tajamal; Shah, Asma Tufail; Shehzad, Khurram; Mujahid, Adnan; Farooqi, Zahoor Hussain; Raza, Muhammad Hamid; Ahmed, Mirza Nadeem; Nisa, Zaib Un

2015-12-01

Uniform porous anodized aluminum oxide (AAO) membrane has been synthesized by two-step anodization for fabricating tungsten trioxide (WO3) nanowires. Under assayed conditions, uniform porous structure of alumina (Al2O3) membrane with long range ordered hexagonal arrangements of nanopores was achieved. The self-assembled template possesses pores of internal diameter of 50 nm and interpore distance ( d int) of 80 nm with a thickness of about 80 µm, i.e., used for fabrication of nanostructures. WO3 nanowires have been fabricated by simple electroless deposition method inside Al2O3 nanopores. SEM images show tungsten trioxide nanowire with internal diameter of about 50 nm, similar to porous diameter of AAO template. XRD results showed that nanowires exist in cubic crystalline state with minor proportion of monoclinic phase.

Selective adsorption of molybdenum(VI) from Mo-Re bearing effluent by chemically modified astringent persimmon

Energy Technology Data Exchange (ETDEWEB)

Xiong Ying, E-mail: xiongying_1977@hotmail.com [School of Chemistry, Key Laboratory of Rare-scattered Elements of Liaoning Province, Liaoning University, Shenyang 110036 (China); Wang Haitao; Lou Zhenning; Shan Weijun; Xing Zhiqiang; Deng Guichun [School of Chemistry, Key Laboratory of Rare-scattered Elements of Liaoning Province, Liaoning University, Shenyang 110036 (China); Wu Dongbei [Department of Chemistry, Tongji University, 200092 (China); Fang Dawei [School of Chemistry, Key Laboratory of Rare-scattered Elements of Liaoning Province, Liaoning University, Shenyang 110036 (China); Biswas, Biplob Kumar [Department of Applied Chemistry, Saga University, Honjo 1, Saga 840-8502 (Japan); Department of Applied Chemistry and Chemical Engineering, Jessore Science and Technology University, Jessore (Bangladesh)

2011-02-28

Graphical abstract: The use of persimmon for the recovery of Mo(VI) from aqueous chloride medium was investigated. The excellent adsorption characteristics for Mo(VI) were confirmed by adsorption and elution tests using a column packed with the APF gel. Research highlights: {yields} Astringent persimmon was chemically cross-linked by formaldehyde to obtain a novel kind of adsorption gel. By comparing with the adsorption of some other metal ions, especially for Re(VII), this new gel exhibited selectivity only for molybdenum with a remarkably high capacity for Mo(VI) (1.05 mol/kg dry gel). {yields} The adsorption mechanisms of molybdenum on the astringent persimmon gel have been determined for deferent molybdenum species. And, the endothermic adsorption process followed pseudo-second order kinetics, and the adsorption behavior obeys the Langmuir mode. {yields} The excellent adsorption characteristics for Mo(VI) were confirmed by adsorption and elution tests using a column packed with the APF gel, especially from an actual industrial waste effluent. - Abstract: Astringent persimmon was chemically cross-linked by formaldehyde to obtain a novel kind of adsorption gel, which was named as APF gel. The adsorption behaviors of Mo(VI) and Re(VII) along with other coexisting metals onto the APF gel were studied in the present paper. The APF gel was found to be effective for the adsorption of Mo(VI) while the gel is almost completely inert toward rhenium and calcium over the whole hydrochloric acid concentration region. The APF gel has a low affinity for iron, copper, lead, nickel, manganese and zinc ions when the concentration of HCl is higher than 1 mol/L. The gel exhibited selectivity only for Mo(VI) with a remarkably high adsorption capacity 1.05 mol/kg, and the adsorption behavior obeys the Langmuir model. According to the thermodynamic and kinetic studies, the endothermic adsorption process followed pseudo-second order kinetics. Also, its excellent adsorption

Effect of molybdenum and iron supply on molybdenum (99Mo) and iron (59Fe) uptake and activity of certain enzymes in tomato plants grown in sand culture

International Nuclear Information System (INIS)

Chatterjee, C.; Agarwala, S.C.

1979-01-01

Tomato (Lycopersicon esculentum Mill. var. Marglobe) plants were raised under controlled sand culture to study the interaction of molybdenum and iron supply on the uptake of molybdenum and iron and activity of certain enzymes affected by iron and/or molybdenum supply. Iron deficiency caused a decrease in the molybdenum uptake and accentuated the effect of molybdenum deficiency in reducing the uptake and more so the translocation of molybdenum from roots to shoots, thus inducing more severe molybdenum deficiency. The deficiency of iron and molybdenum decreased the activity of catalase, succinate dehydrogenase and nitrate reductase, the most marked decrease being found in plants supplied with both iron and molybdenum at low levels. Changes in the activities of nitrate reductase and catalase can be attributed to the interaction of iron and molybdenum supply in their absorption and translocation. (auth.)

Molybdenum-A Key Component of Metal Alloys

Science.gov (United States)

Kropschot, S.J.

2010-01-01

Molybdenum, whose chemical symbol is Mo, was first recognized as an element in 1778. Until that time, the mineral molybdenite-the most important source of molybdenum-was believed to be a lead mineral because of its metallic gray color, greasy feel, and softness. In the late 19th century, French metallurgists discovered that molybdenum, when alloyed (mixed) with steel in small quantities, creates a substance that is remarkably tougher than steel alone and is highly resistant to heat. The alloy was found to be ideal for making tools and armor plate. Today, the most common use of molybdenum is as an alloying agent in stainless steel, alloy steels, and superalloys to enhance hardness, strength, and resistance to corrosion.

Molybdenum solar neutrino experiment

International Nuclear Information System (INIS)

Wolfsberg, K.; Cowan, G.A.; Bryant, E.A.

1984-01-01

The goal of the molybdenum solar neutrino experiment is to deduce the 8 B solar neutrino flux, averaged over the past several million years, from the concentration of 98 Tc in a deeply buried molybdenum deposit. The experiment is important to an understanding of stellar processes because it will shed light on the reason for the discrepancy between theory and observation of the chlorine solar neutrino experiment. Possible reasons for the discrepancy may lie in the properties of neutrinos (neutrino oscillations or massive neutrinos) or in deficiencies of the standard solar model. The chlorine experiment only measures the 8 B neutrino flux in current times and does not address possible temporal variations in the interior of the sun, which are also not considered in the standard model. In the molybdenum experiment, we plan to measure 98 Tc (4.2 Myr), also produced by 8 B neutrinos, and possibly 97 Tc (2.6 Myr), produced by lower energy neutrinos

Determination of molybdenum by the gravimetric plumbate method (with the molybdenum content from 50 % and above)

International Nuclear Information System (INIS)

Stepin, V.V.; Kurbatova, V.I.; Fedorova, N.D.

1980-01-01

A gravimetric method of molybdenum determination in ferromolybdenum (Mo content from 50% and higher) after its dissolving in HNO 3 is developed. The method is based on Mo deposition in acetic acid solution in the form of molybdenum oxide lead after separation of Fe and other interfering elements with sodium hydroxide [ru

Thermodynamic Properties of Manganese and Molybdenum

International Nuclear Information System (INIS)

Desai, P.D.

1987-01-01

This work reviews and discusses the data on the various thermodynamic properties of manganese and molybdenum available through March 1985. These include heat capacity, enthalpy, enthalpy of transitions and melting, vapor pressure, and enthalpy of vaporization. The existing data have been critically evaluated and analyzed. The recommended values for the heat capacity, enthalpy, entropy, and Gibbs energy function from 0.5 to 2400 K for manganese and from 0.4 to 5000 K for molybdenum have been generated, as have heat capacity values for supercooled β-Mn and for γ-Mn below 298.15 K. The recommended values for vapor pressure cover the temperature range from 298.15 to 2400 K for manganese and from 298.15 to 5000 K for molybdenum. These values are referred to temperatures based on IPTS-1968. The uncertainties in the recommended values of the heat capacity range from +-3% to +-5% for manganese and from +-1.5% to +-3% for molybdenum

Abstract: The Reaction between MoO3 and Molten K2S2O7 forming K2MoO2(SO4)2

DEFF Research Database (Denmark)

Nørbygaard, Thomas; Berg, Rolf W.; Nielsen, Kurt

1998-01-01

The present work is part of a general study on metal ore extraction by a pyrosulfate melting process. We report on the formation and structure of colorless crystals, which were prepared by dissolving molybdenum trioxide in molten potassium pyrosulfate at 430 degrees C....

Hydrotreatment activities of supported molybdenum nitrides and carbides

Energy Technology Data Exchange (ETDEWEB)

Dolce, G.M.; Savage, P.E.; Thompson, L.T. [University of Michigan, Ann Arbor, MI (United States). Dept. of Chemical Engineering

1997-05-01

The growing need for alternative sources of transportation fuels encourages the development of new hydrotreatment catalysts. These catalysts must be active and more hydrogen efficient than the current commercial hydrotreatment catalysts. Molybdenum nitrides and carbides are attractive candidate materials possessing properties that are comparable or superior to those of commercial sulfide catalysts. This research investigated the catalytic properties of {gamma}-Al{sub 2}O{sub 3}-supported molybdenum nitrides and carbides. These catalysts were synthesized via temperature-programmed reaction of supported molybdenum oxides with ammonia or methane/hydrogen mixtures. Phase constituents and compositions were determined by X-ray diffraction, elemental analysis, and neutral activation analysis. Oxygen chemisorption was used to probe the surface properties of the catalysts. Specific activities of the molybdenum nitrides and carbides were competitive with those of a commercial sulfide catalyst for hydrodenitrogenation (HDN), hydrodesulfurization (HDS), and hydrodeoxygenation (HDO). For HDN and HDS, the catalytic activity on a molybdenum basis was a strong inverse function of the molybdenum loading. Product distributions of the HDN, HDO and HDS of a variety of heteroatom compounds indicated that several of the nitrides and carbides were more hydrogen efficient than the sulfide catalyst. 35 refs., 8 figs., 7 tabs.

Molybdenum-UO2 cermet irradiation at 1145 K.

Science.gov (United States)

Mcdonald, G.

1971-01-01

Two molybdenum-uranium dioxide cermet fuel pins with molybdenum clad were fission-heated in a forced-convection helium coolant for sufficient time to achieve 5.3% burnup. The cermet core contained 20 wt % of 93.2% enriched uranium dioxide. The results were as follows: there was no visible change in the appearance of the molybdenum clad during irradiation; the maximum increase in diameter of the fuel pins was 0.8%; there was no migration of uranium dioxide along grain boundaries and no evident interaction between molybdenum and uranium dioxide; and, finally, approximately 12% of the fission gas formed was released from the cermet core into the gas plenum.

Spheroidization of molybdenum powder by radio frequency thermal plasma

Science.gov (United States)

Liu, Xiao-ping; Wang, Kuai-she; Hu, Ping; Chen, Qiang; Volinsky, Alex A.

2015-11-01

To control the morphology and particle size of dense spherical molybdenum powder prepared by radio frequency (RF) plasma from irregular molybdenum powder as a precursor, plasma process parameters were optimized in this paper. The effects of the carrier gas flow rate and molybdenum powder feeding rate on the shape and size of the final products were studied. The molybdenum powder morphology was examined using high-resolution scanning electron microscopy. The powder phases were analyzed by X-ray diffraction. The tap density and apparent density of the molybdenum powder were investigated using a Hall flow meter and a Scott volumeter. The optimal process parameters for the spherical molybdenum powder preparation are 50 g/min powder feeding rate and 0.6 m3/h carrier gas rate. In addition, pure spherical molybdenum powder can be obtained from irregular powder, and the tap density is enhanced after plasma processing. The average size is reduced from 72 to 62 µm, and the tap density is increased from 2.7 to 6.2 g/cm3. Therefore, RF plasma is a promising method for the preparation of high-density and high-purity spherical powders.

Features of the kinetics of heterogeneous reactions with phase transformations on catalyst surfaces

Energy Technology Data Exchange (ETDEWEB)

Berman, A D; Krylov, O V

1978-01-01

This paper presents a review of 41 bibliographic references to experiments on the adsorption of various gases (e.g., carbon monoxide, formic acid, ammonia, and oxygen) on metals (e.g., nickel, molybdenum, and platinum) and oxides covers observations of two-dimensional phases during adsorption; the kinetics of adsorption and catalysis associated with two-dimensional phase transitions; and several approximate models for describing the kinetics of heterogeneous catalysis which account for two-dimensional phase transformations on catalyst surfaces.

Monoblock Obturation Technique for Non-Vital Immature Permanent Maxillary Incisors Using Mineral Trioxide Aggregate: Results from Case Series

International Nuclear Information System (INIS)

Iqbal, Z.; Qureshi, A. H.

2014-01-01

Ten patients presented with non-vital immature teeth for root canal treatment. In all these cases the pre-operative clinical examination revealed apical periodontitis with a buccal sinus tract of endodontic origin. These cases were treated by a mineral trioxide aggregate (MTA) monoblock obturation technique. Follow-up evaluations were performed at 1 - 2 years after treatment. Eight out of 10 cases were associated with periradicular healing at follow-up evaluation. Mineral trioxide aggregate Monoblock obturation technique appears to be a valid material to obtain periradicular healing in teeth with open apices and necrotic pulps. (author)

Features of soldering of molybdenum a lols

International Nuclear Information System (INIS)

Grishin, V.L.; Rybkin, B.V.; Cherkasov, A.F.

1980-01-01

Soldering features of complex-alloy molybdenum alloys were investigated in comparison with alloys based on solid solutions. Soldering features of heterogeneous molybdenum base alloys were investigated using samples of 0.5-1.O mm sheets with the strain of about 95% made of ingots which had been smelted in arc vacuum furnaces. The soldering of samples was carried out in 5x1O -5 mm Hg vacuum using different sources of heating: radiation, electron-ray and contact. It was shown that heat-resisting soldered joints of heterogeneous molybdenum alloys could be produced using zirconium and niobium base solders containing the most effective hardeners of the parent material (titanum, vanadium, tantalum, molybdenum, tungsten). To preserve high mechanical properties of heterogeneous alloys it was expedient to use for welding local heating sources which permitted to decrease considerably temperature- time conditions of the process

Feasibility of preparing patterned molybdenum coatings on bismuth telluride thermoelectric modules.

Energy Technology Data Exchange (ETDEWEB)

Sarobol, Pylin; Hall, Aaron Christopher; Miller, Stephen Samuel; Knight, Marlene E.; LePage, William S.; Sobczak, Catherine Elizabeth.; Wesolowski, Daniel Edward

2013-09-01

Molybdenum electrical interconnects for thermoelectric modules were produced by air plasma spraying a 30%CE%BCm size molybdenum powder through a laser-cut Kapton tape mask. Initial feasibility demonstrations showed that the molybdenum coating exhibited excellent feature and spacing retention (~170%CE%BCm), adhered to bismuth-telluride, and exhibited electrical conductivity appropriate for use as a thermoelectric module interconnect. A design of experiments approach was used to optimize air plasma spray process conditions to produce a molybdenum coating with low electrical resistivity. Finally, a molybdenum coating was successfully produced on a fullscale thermoelectric module. After the addition of a final titanium/gold layer deposited on top of the molybdenum coating, the full scale module exhibited an electrical resistivity of 128%CE%A9, approaching the theoretical resistivity value for the 6mm module leg of 112%CE%A9. Importantly, air plasma sprayed molybdenum did not show significant chemical reaction with bismuth-telluride substrate at the coating/substrate interface. The molybdenum coating microstructure consisted of lamellar splats containing columnar grains. Air plasma sprayed molybdenum embedded deeply (several microns) into the bismuth-telluride substrate, leading to good adhesion between the coating and the substrate. Clusters of round pores (and cracks radiating from the pores) were found immediately beneath the molybdenum coating. These pores are believed to result from tellurium vaporization during the spray process where the molten molybdenum droplets (2623%C2%B0C) transferred their heat of solidification to the substrate at the moment of impact. Substrate cooling during the molybdenum deposition process was recommended to mitigate tellurium vaporization in future studies.

Fracture resistance and histological findings of immature teeth treated with mineral trioxide aggregate

DEFF Research Database (Denmark)

Hatibovic-Kofman, S.; Raimundo, L.; Zheng, L.

2008-01-01

The objective of the present study was to test the hypothesis that the fracture strength of calcium hydroxide and mineral trioxide aggregate (MTA)-filled immature teeth decreased over time. Immature mandibular incisors from sheep were extracted and the pulps were extirpated using an apical approach...

Sorption of molybdenum by cellulose polyphosphate from acid solutions

International Nuclear Information System (INIS)

Luneva, N.K.; Oputina, A.G.; Ermolenko, I.N.

1985-01-01

The sorption of molybdenum on cellulose polyphosphate from acid solutions of ammonium molybdate depending on the phosphorus content in samples, concentration and pH of the solution, sorption time is studied. It is shown that a maximum molybdenum content on the cellulose samples with different phosphorus content is pointed out at an ammonium molybdate concentration 0.02 M. Saturation of the sorption curve is attained at molar ratio of adsrbed molybdenum to phosphorus 1:4. In case of small fillings the compound with molybdenum to phosphorus ratio 1:10 is formed

Activity and selectivity of three molybdenum catalysts for coal liquefaction reactions

Energy Technology Data Exchange (ETDEWEB)

Curtis, C.W.; Pellegrino, J.L.

The activity and selectivity of three different molybdenum catalysts for reactions occurring in coal liquefaction, specifically for hydrogenation (HYD), hydrodeoxygenation (HDO), hydrodenitrogenation (HDN), hydrodesulfurization (HDS), and hydrocracking (HYC), have been examined. The three molybdenum catalysts used were molybdenum napthenate, molybdenum on ..gamma..-alumina, and a precipitated, disordered MoS/sub 2/. Molybdenum naphthenate was most selective for HYD and HDN. All three catalysts exhibited approximately equal activity for HDS and HDO and little selectivity for HYC of alkyl bridge structures. The activity and selectivity of the three molybdenum catalysts for producing hydrocarbons and removing heteroatoms from coal during liquefaction were determined and compared. Molybdenum naphthenate was the most active catalyst for hydrocarbon production and removal of nitrogen- and oxygen-containing species during coal liquefaction. 31 refs., 4 figs., 7 tabs.

Deformation localization and cyclic strength in polycrystalline molybdenum

Energy Technology Data Exchange (ETDEWEB)

Sidorov, O.T.; Rakshin, A.F.; Fenyuk, M.I.

1983-06-01

Conditions of deformation localization and its interrelation with cyclic strength in polycrystalline molybdenum were investigated. A fatigue failure of polycrystalline molybdenum after rolling and in an embrittled state reached by recrystallization annealing under cyclic bending at room temperature takes place under nonuniform distribution of microplastic strain resulting in a temperature rise in separate sections of more than 314 K. More intensive structural changes take place in molybdenum after rolling than in recrystallized state.

Bibliographic study on molybdenum biokinetics. Literaturstudie zur Biokinetik von Molybdaen

Energy Technology Data Exchange (ETDEWEB)

Erzberger, A.

1988-05-01

This bibliographical study compiles and analyzes findings about the metabolism and resorption of molybdenum. Besides including studies on the physiology of molybdenum 99, a general survey is given on molybdenum in the environment and on its physiological behaviour. In particular, information on the dependence of molybdenum resorption on various factors, such as the chemical form, antagonisms etc., are gathered from literature. These factors have to be considered for sensibly carrying out necessary experiments.

Kinetic interaction in hydrogenitrogenation of quinoline and acridine

International Nuclear Information System (INIS)

El-Bishtawi, R.F.; Seapan, M.

1988-01-01

Liquid fossil fuels contain numerous nitrogen compounds. During hydrodenitrogenation processes, these compounds for the active catalytic sites, with each compound affecting the kinetics of the other compounds. An understanding of the kinetic interaction is essential in using the results of model compound kinetics to predict the behavior of complex mixtures. In this work, the authors study the hydrodenitrogenation of quinoline and acridine in n-hexadecane over a commercial nickel-molybdenum catalyst in a batch autoclave reactor at 8.3 MPa (1200 psig) and 357-390 0 C. The reaction networks and kinetics of individual compounds were developed. These results confirm the existing knowledge of reaction networks for quinoline and acridine. Furthermore, their experiments show that formation for o-ethylaniline, o-toluidine and aniline are also important steps in quinoline denitrogenation. For total nitrogen removal, a dual site Langmuir-Hinshelwood type model considering separate sites for adsorption of hydrogen and nitrogen compounds give the best fit

Thermal cyclic strength of molybdenum monocrystal at high temperatures

International Nuclear Information System (INIS)

Strizhalo, V.A.; Uskov, E.I.

1975-01-01

The results of the investigation of the thermocyclic creep and low-cycle fatigue of a molybdenum single crystal are discussed. The strength of a molybdenum single crystal under nonisothermal stressing has been investigated by using two different regimes of temperature and load variation. The temperature limits of the cycle were the same for the two testing regimes, the maximum temperature being 1700degC and the minimum 350degC. At higher temperatures (above 1500degC) the short-term strength of single-crystal molybdenum is comparable with that of commercial molybdenum and the refractory alloys, while the ductility is considerably higher. It should be noted that the failure of single-crystal molybdenum under rigid alternating loading is preceded by intensive distortion of the specimen, owing to directional cyclic creep of the metal in zones of bulging and thinning

Exploring atomic defects in molybdenum disulphide monolayers

KAUST Repository

Hong, Jinhua; Hu, Zhixin; Probert, Matt; Li, Kun; Lv, Danhui; Yang, Xinan; Gu, Lin; Mao, Nannan; Feng, Qingliang; Xie, Liming; Zhang, Jin; Wu, Dianzhong; Zhang, Zhiyong; Jin, Chuanhong; Ji, Wei; Zhang, Xixiang; Yuan, Jun; Zhang, Ze

2015-01-01

Defects usually play an important role in tailoring various properties of two-dimensional materials. Defects in two-dimensional monolayer molybdenum disulphide may be responsible for large variation of electric and optical properties. Here we present a comprehensive joint experiment-theory investigation of point defects in monolayer molybdenum disulphide prepared by mechanical exfoliation, physical and chemical vapour deposition. Defect species are systematically identified and their concentrations determined by aberration-corrected scanning transmission electron microscopy, and also studied by ab-initio calculation. Defect density up to 3.5 × 10 13 cm '2 is found and the dominant category of defects changes from sulphur vacancy in mechanical exfoliation and chemical vapour deposition samples to molybdenum antisite in physical vapour deposition samples. Influence of defects on electronic structure and charge-carrier mobility are predicted by calculation and observed by electric transport measurement. In light of these results, the growth of ultra-high-quality monolayer molybdenum disulphide appears a primary task for the community pursuing high-performance electronic devices.

Exploring atomic defects in molybdenum disulphide monolayers

KAUST Repository

Hong, Jinhua

2015-02-19

Defects usually play an important role in tailoring various properties of two-dimensional materials. Defects in two-dimensional monolayer molybdenum disulphide may be responsible for large variation of electric and optical properties. Here we present a comprehensive joint experiment-theory investigation of point defects in monolayer molybdenum disulphide prepared by mechanical exfoliation, physical and chemical vapour deposition. Defect species are systematically identified and their concentrations determined by aberration-corrected scanning transmission electron microscopy, and also studied by ab-initio calculation. Defect density up to 3.5 × 10 13 cm \\'2 is found and the dominant category of defects changes from sulphur vacancy in mechanical exfoliation and chemical vapour deposition samples to molybdenum antisite in physical vapour deposition samples. Influence of defects on electronic structure and charge-carrier mobility are predicted by calculation and observed by electric transport measurement. In light of these results, the growth of ultra-high-quality monolayer molybdenum disulphide appears a primary task for the community pursuing high-performance electronic devices.

Molybdenum silicide based materials and their properties

International Nuclear Information System (INIS)

Yao, Z.; Stiglich, J.; Sudarshan, T.S.

1999-01-01

Molybdenum disilicide (MoSi 2 ) is a promising candidate material for high temperature structural applications. It is a high melting point (2030 C) material with excellent oxidation resistance and a moderate density (6.24 g/cm 3 ). However, low toughness at low temperatures and high creep rates at elevated temperatures have hindered its commercialization in structural applications. Much effort has been invested in MoSi 2 composites as alternatives to pure molybdenum disilicide for oxidizing and aggressive environments. Molybdenum disilicide-based heating elements have been used extensively in high-temperature furnaces. The low electrical resistance of silicides in combination with high thermal stability, electron-migration resistance, and excellent diffusion-barrier characteristics is important for microelectronic applications. Projected applications of MoSi 2 -based materials include turbine airfoils, combustion chamber components in oxidizing environments, missile nozzles, molten metal lances, industrial gas burners, diesel engine glow plugs, and materials for glass processing. On this paper, synthesis, fabrication, and properties of the monolithic and composite molybdenum silicides are reviewed

Molybdenum: the element and aqueous solution chemistry

International Nuclear Information System (INIS)

Sykes, A.G.

1987-01-01

This chapter on the chemistry of the coordination compounds of molybdenum concentrates on the element itself, its recovery from ores and its use in the manufacture of steels. Most of the chapter is devoted to the aqueous solution chemistry of molybdenum in oxidation states II, III and IV. (UK)

Low-temperature heat capacity of molybdenum borides

International Nuclear Information System (INIS)

Bolgar, A.S.; Klinder, A.V.; Novoseletskaya, L.M.; Turov, V.P.; Klochkov, L.A.; Lyashchenko, A.B.

1988-01-01

Heat capacity of molybdenum borides Mo 2 B, MoB, Mo 2 B 5 is studied for the first time in the 60-300 K range using the adiabatic method. Standard (at 298.15 K) thermodynamic functions (enthalpy, heat capacity, entropy, reduced Gibbs energy) of molybdenum borides are calculated

XUV spectra of highly ionised molybdenum

Energy Technology Data Exchange (ETDEWEB)

Mansfield, M W.D.; Peacock, N J; Smith, C C; Hobby, M G [UKAEA, Abingdon. Culham Lab.; Cowan, R D

1978-05-14

The spectra of molybdenum ions produced in Tokamaks in the wavelength range 10-200 A have been reproduced in a plasma formed by laser beam irradiation of solid molybdenum targets. Lines from highly ionised stages of molybdenum (Mo XXX to Mo XXXII) have been distinguished by varying the laser beam intensity. Detailed analyses of the simpler ions, Mo XV (Ni-like), Mo XVI (Co-like), Mo XXXII (Na-like), and to a lesser extent Mo XXXI (Mg-like) and Mo XVII (Fe-like), have been achieved by comparison with ab initio calculations. A general interpretation of intermediate ion stages is also given but it is shown that most of these spectra are so complex, as a result of inner-subshell excitation, that detailed term-scheme analyses are nearly impossible.

Importance of molybdenum in the nitrogen metabolism of microorganisms and higher plants

Energy Technology Data Exchange (ETDEWEB)

Mulder, E G

1948-01-01

The effect of molybdenum on the growth of microorganisms and higher plants and on some well-defined biochemical reactions was investigated. Results indicate that Aspergillus niger requires small amounts of molybdenum when growing in a culture solution supplied with nitrate nitrogen. With ammonium sulfate as a source of nitrogen, the response of the fungus to molybdenum was much smaller. It was shown that this different response of Aspergillus to molybdenum was not brought about by a difference in purity of both nitrogen compounds used, nor by a difference in absorption of the molybdenum impurity, but by a considerably higher requirement of molybdenum in a medium with nitrate nitrogen. The growth-rate curve and the increasing sporulation of Aspergillus niger with increasing amounts of molybdenum were used in estimating very small amounts of this element in various materials. In culture solution experiments with tomato, barley and oat plants the effect of traces of molybdenum on the growth of these plants was investigated. In good agreement with the results of the experiments with Aspergillus and denitrifying bacteria it could be shown that in the green plant as in these microorganisms molybdenum is acting as a catalyst in nitrate reduction. In experiments with Azotobacter chroococcum and leguminous plants the effect of molybdenum on the fixation of gaseous N/sub 2/ was studied. In culture solutions with pea plants the effect of molybdenum on the nitrogen fixation of the nodules was investigated. In the absence of molybdenum as well as in a complete nutrient medium many nodules were formed. 30 references, 6 figures, 16 tables.

Separation of uranium from molybdenum by alkyl phosphoric acid extraction

Energy Technology Data Exchange (ETDEWEB)

Zhongshi, Li

1986-08-01

The regularities of separation of uranium from molybdenum by alkyl phosphoric acid extraction are described. Two parameters, i.e., density ratio of uranium to molybdenum in organic phase at first stage and density of uranium in raffinate at last stage are presented. The relationship between these parameters and purity of molybdenum and uranium products is given. The method of adjusting and controlling these parameters in experiments and production is worked out. The technical key problem in comprehensive utilization of sedimentary type uranium ore containing molybdenum with close concentration of these to elements has been solved.

Activity of molybdenum-containing oxide catalysts in the reaction of ethane oxidation

International Nuclear Information System (INIS)

Konovalov, V.I.; Ehpova, T.I.; Shchukin, V.P.; Averbukh, A.Ya.

1977-01-01

Investigation results concerning the catalytic activity of molybdenum-containing catalysts in ethane oxidation reaction are presented. It has been found that the greatest activity in the temperature range from 450 to 600 deg C is exhibited by cobalt-molybdenum catalyst; at 600 deg C bismuth-molybdenum catalyst is the most active. Nickel-molybdenum catalyst is selective and active with respect to ethylene. Iron- and manganese-molybdenum catalysts do not show high ethane oxidation rates and their selectivity is insignificant

Alkaline elution of uranium and molybdenum and their recovery

International Nuclear Information System (INIS)

Song Wenlan; Wu Peisheng; Zhao Pinzhi; Tao Dening; Xie Chaoyan

1987-01-01

The uranium and molybdenum can be simultaneously eluted by using eluant (NH 4 ) 2 CO 3 + (NH 4 ) 2 SO 4 from resin loaded uranium and molybdenum. The ADU is precipitated from eluant by volatilization of ammonia. The molybdenum is extracted by TFA-TBP-kerosene from the filtrate at pH 3.0-3.2 with molybdenum extraction > 98%. Uranium is nearly not extracted. The precipitation of Mo is reached by sulphuric acid after stripping and the ammonium multimolybdate is obtained. This process can give the total recovery more than 99% for U and 90% for Mo. Because of the use of sulphate salt system, the hazard of NO 3 - can be avoided

Molybdenum erosion measurements in Alcator C-Mod

Energy Technology Data Exchange (ETDEWEB)

Wampler, W.R. [Sandia National Labs., Albuquerque, NM (United States); LaBombard, B.; Lipshultz, B.; Pappas, D.; Pitcher, C.S. [Massachusetts Inst. of Tech., Cambridge, MA (United States); McCracken, G.M. [JET Joint Undertaking, Abingdon (United Kingdom)

1998-05-01

Erosion of molybdenum was measured on a set of 21 tiles after a run campaign of 1,090 shots in the Alcator C-Mod tokamak. The net erosion of molybdenum, was determined from changes in the depth of a thin chromium marker layer measured by Rutherford backscattering. Net Mo erosion was found to be approximately 150 nm near the outer divertor strike point, and much less everywhere else. Gross erosion rates by sputtering were estimated using ion energies and fluxes obtained from Langmuir probe measurements of edge-plasma conditions. Predicted net erosion using calculated gross erosion with prompt redeposition and measured net erosion agree within a factor of 3. Sputtering by boron and molybdenum impurities dominates erosion.

Extraction of molybdenum VI by alpha benzoinoxime

International Nuclear Information System (INIS)

Achache, M.; Meklati, M.

1990-06-01

The concentration of molybdenum, was studied using alpha benzoinoxime dissolved in chloroform. Several acids and salt at different levels of concentration were investigated as well as other parameters such as (mixing time, extractant to metal ratio, temperature etc.) The molybdenum stippling was also studied in alkaline medium with the subsequent recovery of the extractant and solvent

Synthesis of molybdenum borides and molybdenum silicides in molten salts and their oxidation behavior in an air-water mixture

NARCIS (Netherlands)

Kuznetsov, S.A.; Kuznetsova, S.V.; Rebrov, E.V.; Mies, M.J.M.; Croon, de M.H.J.M.; Schouten, J.C.

2005-01-01

The formation of various coatings in molybdenum-boron and molybdenum-silicon systems was investigated. Boronizing and siliciding treatments were conducted in molten salts under inert gas atm. in the 850-1050 DegC temp. range for 7 h. The presence of boride (e.g. Mo2B, MoB, Mo2B5) and silicide

Weldability of powder-metallurgy molybdenum with low oxygen content

International Nuclear Information System (INIS)

Hiraoka, Yutaka; Okada, Masatoshi

1987-01-01

Relationships between the formation of weld pores and the chemical compositions in powder-metallurgy molybdenum were investigated. It is suggested that almost 100% of Ca and Mg form oxides. In contrast, Fe, Ni, Cr and Al, Si only partly form oxides. A powder-metallurgy molybdenum containing less than 84 at.ppm oxygen did not show any large weld pores. The reduction of the oxygen content was achieved by purifying the molybdenum powder. (orig.) [de

Separation and selective determination of molybdenum with sodiumthiosulfate and ethylacetate

International Nuclear Information System (INIS)

Hainberger, L.; de Oliveira Andrade, W.

1982-01-01

A sensitive and selective method of spectrophotometric determination of molybdenum is described. Molybdenum is extracted to more than 97%. Lambert-Beer's law is obeyed between 0.35 and 30μg/10ml of the used aqueous solution. 43 ions concerning their interference are studied. The method was used to determine the content of molybdenum in black beans. (Author)

Friction and corrosion resistance of sputter deposited supersaturated metastable aluminium-molybdenum alloys

Energy Technology Data Exchange (ETDEWEB)

Abu-Zeid, O.A. [Univ. of the United Arab Emirates, Al-Ain (United Arab Emirates). Dept. of Mech. Eng.; Bates, R.I. [Design, Mfg. and Marketing Research Inst., Univ. of Salford (United Kingdom)

1996-12-15

Two closed field unbalanced magnetrons with targets of aluminium and molybdenum have been used for the co-deposition of aluminium-molybdenum coatings with different compositions. A pin on disk machine and a computer controlled potentiostat have been used to evaluate respectively, the tribological and corrosion properties of the deposited alloys. Results have shown that introducing molybdenum into aluminium coatings improves their poor tribological properties. Aluminium-molybdenum coatings with different compositions have shown low wear behaviour and for coatings with high molybdenum contents (> 80%) friction coefficients against steel, as low as 0.18 have been obtained. The addition of molybdenum into aluminium coatings has reduced their corrosion tendency and corrosion current density in a marine environment. (orig.)

Molybdenum plasma spray powder, process for producing said powder, and coating made therefrom

International Nuclear Information System (INIS)

Lafferty, W.D.; Cheney, R.F.; Pierce, R.H.

1979-01-01

Plasma spray powders of molybdenum particles containing 0.5 to 15 weight percent oxygen and obtained by reacting molybdenum particles with oxygen or oxides in a plasma, form plasma spray coatings exhibiting hardness comparable to flame sprayed coatings formed from molybdenum wire and plasma coatings of molybdenum powders. Such oxygen rich molybdenum powders may be used to form wear resistant coatings, such as for piston rings. (author)

Solid solutions of hydrogen in niobium, molybdenum and their alloys

International Nuclear Information System (INIS)

Ishikawa, T.T.

1981-01-01

The solubility of hydrogen in niobium, molybdenum and niobium-molybdenum alloys with varying atomic fraction of molybdenum from 0.15 to 0.75 was measured on the temperature range of 673 0 K to 1273 0 k for one atmosphere hydrogen pressure. The experimental technique involved the saturation of the solvent metal or alloy with hydrogen, followed by quenching and analysis of the solid solution. The results obtained of hydrogen solubility are consistent with the quasi-regular model for the dilute interstitial solid solutions. The partial molar enthalpy and partial molar entropy in excess of the dissolved hydrogen atoms were calculated from data of solubility versus reciprocal doping temperature. The variation of the relative partial molar enthalpy of hydrogen dissolved in niobium-molybdenum alloys, with the increase of molybdenum content of the alloy was analized. (Author) [pt

Potentiometric titration of molybdenum (6) with a cathode-polarized solid electrode

International Nuclear Information System (INIS)

Boeva, L.V.; Kimstach, V.A.; Bagdasarov, K.N.

1980-01-01

The possibility has been studied of using solid electrodes for potentiometric precipitation titration of molybdenum (6). A cathode-polarized electrode, electrochemically covered with a molybdenum blue layer, can be used as indicator electrode. The best results were obtained during deposition of molybdenum blue on a tungsten electrode. The mechanism of electrode work during titration has been investigated. A procedure has been developed of titration of molybdenum (6) in acid solutions using hydroxylamine N-aryl derivatives as titrants

Electrical properties of tungsten trioxide films

International Nuclear Information System (INIS)

Xu, Z.; Vetelino, J.F.; Lec, R.; Parker, D.C.

1990-01-01

Selectively doped semiconducting metal oxide (SMO) films have been shown to have applications as the sensing element in gas microsensors. Critical to the design and operation of these sensors is the SMO film. In the present work, the electrical properties of both intrinsic and extrinsic (doped with gold) tungsten trioxide (WO 3 ) films, which selectively sorb hydrogen sulfide (H 2 S), are investigated. Hall effect measurements are performed as a function of film thickness, temperature, gold-doping concentration, and H 2 S gas concentration. The conductivity was found to be n type and strongly dependent on temperature, gold doping concentration, and H 2 S gas concentration and less dependent on film thickness. The mobility was relatively high while the intrinsic carrier concentration was low when compared to typical semiconductor materials. The conductivity was shown to exhibit anomalous behavior at certain temperatures and H 2 S gas concentrations

Recovery of molybdenum metal powder from a low grade molybdenite concentrate

International Nuclear Information System (INIS)

Mukherjee, T.K.; Menon, P.R.; Shukla, P.P.; Gupta, C.K.

1988-01-01

An account is given of the development of a process for the production of molybdenum metal powder from a low grade molybdenite concentrate. The molybdenum value present in the concentrate was leached with a dilute hypochlorite solution generated in-situ by electrolysis of brine solution. The leach liquor was subsequently purified by carbon adsorption process. The leach liquor was chemically processed to recover the molybdenum value in the forms of calcium molybdate and ammonium molybdate salts. These molybdenum intermediates were hydrogen-reduced to metallic molybdenum powder. The experimental set up used, procedure followed and results obtained are discussed and a flowsheet indicating the entire processing scheme is included. 11 refs., 4 figs., 8 tabs

Experiment on bio-leaching of associated molybdenum and uranium ore

International Nuclear Information System (INIS)

Zheng Ying; Fan Baotuan; Liu Jian; Meng Yunsheng; Liu Chao

2007-01-01

Column leaching experiment results on associated molybdenum uranium ore by bacteria (T. f) are introduced. The ore are leached for 210 days using bacteria domesticated to tolerate molybdenum, the leaching of uranium is of 98% and leaching of molybdenum is of 41%. Sulphuric acid produced by bio-oxidation of sulfides in ore can meet the demand of ore leaching. (authors)

Microstructure and mechanical properties of multi-components rare earth oxide-doped molybdenum alloys

International Nuclear Information System (INIS)

Zhang Guojun; Sun Yuanjun; Zuo Chao; Wei Jianfeng; Sun Jun

2008-01-01

Pure molybdenum and molybdenum alloys doped with two- or three-components rare earth oxide particles were prepared by powder metallurgy. Both the tensile property and fracture toughness of the pure molybdenum and multi-components rare earth oxide-doped molybdenum alloys were determined at room temperature. The multi-components rare earth oxide-doped molybdenum alloys are fine grained and contain a homogeneous distribution of fine particles in the submicron and nanometer size ranges, which is why the molybdenum alloys have higher strength and fracture toughness than pure molybdenum. Quantitative analysis is used to explain the increase in yield strength with respect to grain size and second phase strengthening. Furthermore, the relationship between the tensile properties and microstructural parameters is quantitatively established

Colour centres in amorphous tungsten trioxide thin films

International Nuclear Information System (INIS)

Kleperis, J.J.; Cikmach, P.D.; Lusis, A.R.

1984-01-01

Magnetic, optical, and electrical properties of thin tungsten trioxide (a-WO 3 ) films obtained on substrates with different temperatures and annealed in air and vacuum are investigated. On the basis of these results and recent structural investigations a structure model of the a-WO 3 film is given: a spatial network of tightly bounded clusters which are built from hydrated WO 6 octahedra. These octahedra contain terminal oxygens and being axially distorted they are the sites for localization of injected electrons. The colour centres formed are paramagnetic (ESR signal from W 5+ ) and their optical absorption is satisfactorily described by the intervalence charge transfer between the localized states of W 5+ and W 6+ ions. (author)

Investigation of pressing of molybdenum powder compacts

International Nuclear Information System (INIS)

Mymrin, S.A.; Kuznetsov, V.Eh.; Yampol'skij, M.L.; Leonov, S.A.; Mikhridinov, R.M.; Korzukhin, V.A.

1990-01-01

Results of an experimental investigation into pressing of compacts of MCh type molybdenum powders using the industrial equipment are presented. To measure the density of powder molybdenum billets a radioisotopic density meter with cesium-137 is used as radioactive gamma radiation source. The dependence of the produced billet density on the specific compacting pressure at different values of the powder bulk density is ascertained

The XUV spectra of highly ionised molybdenum

International Nuclear Information System (INIS)

Mansfield, M.W.D.; Peacock, N.J.; Smith, C.C.; Hobby, M.G.; Cowan, R.D.

1978-01-01

The spectra of molybdenum ions produced in Tokamaks in the wavelength range 10-200 A have been reproduced in a plasma formed by laser beam irradiation of solid molybdenum targets. Lines from highly ionised stages of molybdenum (Mo XXX to Mo XXXII) have been distinguished by varying the laser beam intensity. Detailed analyses of the simpler ions, Mo XV (Ni-like), Mo XVI (Co-like), Mo XXXII (Na-like), and to a lesser extent Mo XXXI (Mg-like) and Mo XVII (Fe-like), have been achieved by comparison with ab initio calculations. A general interpretation of intermediate ion stages is also given but it is shown that most of these spectra are so complex, as a result of inner-subshell excitation, that detailed term-scheme analyses are nearly impossible. (author)

A study on the kinetics of hydrogen reduction of molybdenum disulphide powders

International Nuclear Information System (INIS)

Mehdi Afsahi, M.; Sohrabi, Morteza; Vasant Kumar, R.; Ale Ebrahim, Habib

2008-01-01

In order to achieve direct reduction of molybdenite in presence of a sulphur scavenger such as CaO such that SO 2 emission is completely avoided, it is important to maximise the rate of the partial reaction involving molybdenite and hydrogen (without lime) given the low thermodynamic driving force for this reaction. Accordingly, reaction of molybdenum disulphide powders with hydrogen was investigated by thermogravimetric method. Effect of temperature and concentration on the reaction rate was studied under such conditions that resistance to mass transfer arising from external film, between particles and intra-grain was negligible. The operating temperature ranged between 973 and 1173 K while the hydrogen concentration was varied between 30 and 100%. The experimental data obtained under the above conditions were analyzed by applying 'the shrinking unreacted core model'. The reduction reaction was found to be first order with respect to the gaseous reactant. Pre-exponential factor and activation energy have been determined to be 3.91 x 10 3 cm min -1 and 139.0 kJ mol -1 , respectively. Activation energy obtained from a fitted model, agreed well with the values determined from the model-free methods using isothermal measurements

Reduction and immobilization of molybdenum by Desulfovibrio desulfuricans

Energy Technology Data Exchange (ETDEWEB)

Tucker, M.D.; Barton, L.L.; Thomson, B.M. [Sandia National Laboratories, Albuquerque, NM (United States)

1997-07-01

Molybdenum contamination of groundwater occurs through activities such as molybdenum and copper mining and processing, shale oil production and power generation from coal-fired power plants. The mobility of Mo in the environment is strongly dependent on its chemical oxidation state. Under oxidizing conditions, Mo occurs as highly soluble and mobile Mo(VI) and Mo(V) compounds. However, under reducing conditions Mo usually forms insoluble Mo(IV) phases. The objective of this study was to demonstrate the ability of the sulfate-reducing bacterium, Desulfovibrio desulfuricans, to reduce Mo(IV) to Mo(IV) in anaerobic environments. Molybdenum-VI was reduced to Mo(IV) by washed cells of D. desulfuricans suspended in bicarbonate buffer solution with either lactate or H{sub 2} as the electron donor and Mo(VI) as the electron acceptor. Molybdenum-VIi reduction by D. desulfuricans in the presence of sulfide resulted in the extracelluar precipitation of the mineral molybdenite. Molybdenum-VI reduction did not occur in the absence of an electron donor or in the presence of heat-killed cells of D. desulfuricans. The results indicate that enzymatic reduction of Mo(VI) by sulfate-reducing bacteria may contribute to the accumulation of Mo(IV) in anaerobic environments and that there organisms may be useful for removing soluble Mo from contaminated water. 20 refs., 6 figs., 4 tabs.

Uranium and Molybdenum extraction from a Cerro Solo deposit ore

International Nuclear Information System (INIS)

Becquart, Elena T.; Arias, Maria J.; Fuente, Juan C. de la; Misischia, Yamila A.; Santa Cruz, Daniel E.; Tomellini, Guido C.

2009-01-01

Cerro Solo, located in Chubut, Argentina, is a sandstone type uranium-molybdenum deposit. Good recovery of both elements can be achieved by acid leaching of the ore but the presence of molybdenum in pregnant liquors is an inconvenient to uranium separation and purification. A two steps process is developed. A selective alkaline leaching of the ore with sodium hydroxide allows separating and recovering of molybdenum and after solid-liquid separation, the ore is acid leached to recover uranium. Several samples averaging 0,2% uranium and 0,1% molybdenum with variable U/Mo ratio have been used and in both steps, leaching and oxidant reagents concentration, temperature and residence time in a stirred tank leaching have been studied. In alkaline leaching molybdenum recoveries greater than 96% are achieved, with 1% uranium extraction. In acid leaching up to 93% of the uranium is extracted and Mo/U ratio in solvent extraction feed is between 0,013 and 0,025. (author)

Mechanical properties of molybdenum coated with titanium carbide film

International Nuclear Information System (INIS)

Shikama, T.; Shinno, H.; Fukutomi, M.; Fujitsuka, M.; Okada, M.

1983-01-01

TiC-coated molybdenum is mechanically tensile tested. The 6 μm thick TiC-coated molybdenum has a higher 0.2% proof strength with a slight decrease in uniform and rupture elongation than the uncoated one. This strengthening effect of the TiC coating can be explained by the constrained effect of the high strength TiC film. The 1.2 μm thick TiC-coated molybdenum starts its plastic deformation at a lower stress than the uncoated one. Also, the coating makes the stress-strain curve more smooth. These effects are attributed to the surface effect, namely, that the interface between the molybdenum substrate and the strong and brittle TiC film acts as a strong dislocation source. The compressive stress in the TiC film will also help the start of plastic deformation at lower external stresses. (author)

Addition of Arsenic Trioxide into Induction Regimens Could Not Accelerate Recovery of Abnormality of Coagulation and Fibrinolysis in Patients with Acute Promyelocytic Leukemia.

Directory of Open Access Journals (Sweden)

Ye Zhang

Full Text Available All-trans retinoic acid combined to anthracycline-based chemotherapy is the standard regimen of acute promyelocytic leukemia. The advent of arsenic trioxide has contributed to improve the anti-leukemic efficacy in acute promyelocytic leukemia. The objectives of the current study were to evaluate if dual induction by all-trans retinoic acid and arsenic trioxide could accelerate the recovery of abnormality of coagulation and fibrinolysis in patients with acute promyelocytic leukemia.Retrospective analysis was performed in 103 newly-diagnosed patients with acute promyelocytic leukemia. Hemostatic variables and the consumption of component blood were comparably analyzed among patients treated by different induction regimen with or without arsenic trioxide.Compared to patients with other subtypes of de novo acute myeloid leukemia, patients with acute promyelocytic leukemia had lower platelet counts and fibrinogen levels, significantly prolonged prothrombin time and elevated D-dimers (P<0.001. Acute promyelocytic leukemia patients with high or intermediate risk prognostic stratification presented lower initial fibrinogen level than that of low-risk group (P<0.05. After induction treatment, abnormal coagulation and fibrinolysis of patients with acute promyelocytic leukemia was significantly improved before day 10. The recovery of abnormal hemostatic variables (platelet, prothrombin time, fibrinogen and D-dimer was not significantly accelerated after adding arsenic trioxide in induction regimens; and the consumption of transfused component blood (platelet and plasma did not dramatically change either. Acute promyelocytic leukemia patients with high or intermediate risk prognostic stratification had higher platelet transfusion demands than that of low-risk group (P<0.05.Unexpectedly, adding arsenic trioxide could not accelerate the recovery of abnormality of coagulation and fibrinolysis in acute promyelocytic leukemia patients who received all

Crystalline silicon films sputtered on molybdenum A study of the silicon-molybdenum interface

Energy Technology Data Exchange (ETDEWEB)

Reinig, P.; Fenske, F.; Fuhs, W.; Schoepke, A.; Selle, B

2003-04-15

Polycrystalline silicon films were grown on molybdenum (Mo)-coated substrates at high deposition rate using the pulsed magnetron sputtering technique. Our study investigates the silicon-molybdenum interface of these films to elucidate stimulating mechanisms for an ordered crystalline silicon thin film growth. Both Auger electron spectroscopy and Rutherford backscattering reveal that at a substrate temperature as low as T{sub S}=450 deg. C during the deposition process intermixing of Si and Mo at the Si-Mo interface takes place leading to a compositional ratio Mo:Si of about 1:2. By Raman spectroscopy hexagonal {beta}-MoSi{sub 2} could be identified as the dominant phase in this intermixed region. The dependence of the resulting thickness of the reacted interface layer on the deposition conditions is not fully understood yet.

Crystalline silicon films sputtered on molybdenum A study of the silicon-molybdenum interface

International Nuclear Information System (INIS)

Reinig, P.; Fenske, F.; Fuhs, W.; Schoepke, A.; Selle, B.

2003-01-01

Polycrystalline silicon films were grown on molybdenum (Mo)-coated substrates at high deposition rate using the pulsed magnetron sputtering technique. Our study investigates the silicon-molybdenum interface of these films to elucidate stimulating mechanisms for an ordered crystalline silicon thin film growth. Both Auger electron spectroscopy and Rutherford backscattering reveal that at a substrate temperature as low as T S =450 deg. C during the deposition process intermixing of Si and Mo at the Si-Mo interface takes place leading to a compositional ratio Mo:Si of about 1:2. By Raman spectroscopy hexagonal β-MoSi 2 could be identified as the dominant phase in this intermixed region. The dependence of the resulting thickness of the reacted interface layer on the deposition conditions is not fully understood yet

Study of molybdenum(VI) dimerization equilibrium in strongly acidic medium

International Nuclear Information System (INIS)

Esbelin, E.

2000-01-01

Molybdenum (VI) was investigated spectro-photometrically in non complexing and strongly acidic medium for the first time by Krumenacker. Cationic species of molybdenum were identified by electrophoresis on cellulose paper in highly acidic solutions. From these early results using absorption spectrophotometry, Krumenacker postulated the condensation of molybdenum in this medium. He studied the polymeric species by measuring diffusion coefficients and identified the polymeric form as a dimer. He described the system by equations (1) and (2). Cruywagen later added two equations (3) and (4) to supplement the description of the system. The aim of this work was to re-examine the conditional dimerization equilibrium between the various species of molybdenum(VI) in strongly acid medium by focussing on the influence of the medium. All Mo solution concentrations were analyzed by ICP-AES. Absorbance of the solutions were measured with a VARIAN model CARY5 spectrophotometer in double beam mode with air as reference; blank solutions contained all reagents except molybdenum. The quartz cell path length was 1 mm. The dimerization of monomeric molybdenum(VI) was investigated spectro-photometrically at perchloric acid concentrations of 0.5, 1.0, 2.0 and 3 M at 25 deg C. Two absorption bands at 215 and 245 nm were observed and attributed to monomeric and dimeric forms respectively. The variations in the conditional molar absorption coefficient of molybdenum with total molybdenum(VI) concentration is indicative of several molybdenum forms involved in the total absorbance. Dimerization equilibrium is defined by equation (5). By using the additivity of absorbance and mass conservation of molybdenum, a descriptive equation of the 'spectrochemical' system is developed. This equation is linearized into two forms (6) et (7). From them, two refinement methods were used to estimate the conditional dimerization constant K' d for various medium concentrations. This numerical procedure offers

Femtosecond laser surface structuring of molybdenum thin films

Energy Technology Data Exchange (ETDEWEB)

Kotsedi, L., E-mail: Kotsedi@tlabs.ac.za [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk ridge, PO Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, PO Box 722, Somerset West, Western Cape Province (South Africa); Mthunzi, P. [Council for Scientific and Industrial Research (CSIR), Biophotonics Lab: National Laser Centre Pretoria, 0001 (South Africa); Nuru, Z.Y. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk ridge, PO Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, PO Box 722, Somerset West, Western Cape Province (South Africa); Eaton, S.M. [Physics Department, Politecnico di Milano, Piazza Leonardo Da Vinci, 32, 20133 Milano (Italy); Center for Nano Science and Technology, Istituto Italiano di Tecnologia, Via Pascoli 70/3, 20133 Milano, Itala (Italy); Sechoghela, P.; Mongwaketsi, N. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk ridge, PO Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, PO Box 722, Somerset West, Western Cape Province (South Africa); Ramponi, R. [Institute for Photonics and Nanotechnologies (IFN)–CNR, Piazza Leanardo Da Vinci, 32, 20133 Milano (Italy); Maaza, M. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk ridge, PO Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, PO Box 722, Somerset West, Western Cape Province (South Africa)

2015-10-30

Highlights: • Color change of the molybdenum thin film from shinny to violet–yellowish color after laser irradiation at various laser powers. • Formation of the molybdenum dioxide coating after laser exposure, as confirmed by the X-ray diffraction spectrometry. • Selective solar absorbing nature of the laser exposed films. • Study of the binding energies is presented in this contribution using the XPS spectrometry. - Abstract: This contribution reports on the femtosecond surface structuring of molybdenum thin coatings deposited by electron beam evaporation onto Corning glass substrates. The 1-D type periodic grating lines created by such an ablation showed that the widths of the shallow grooves followed a logarithmic dependence with the laser energy incident on the molybdenum film. The electronic valence “x” of the created oxide surface layer MoO{sub x} was found to be incident laser power dependent via Rutherford backscattering spectrometry, X-ray photoelectron spectroscopy and X-ray diffraction investigations. Such a photo-induced MoO{sub x}–Mo nanocomposite exhibited effective selective solar absorption in the UV–vis–IR spectral range.

A molybdenum disulfide/carbon nanotube heterogeneous complementary inverter.

Science.gov (United States)

Huang, Jun; Somu, Sivasubramanian; Busnaina, Ahmed

2012-08-24

We report a simple, bottom-up/top-down approach for integrating drastically different nanoscale building blocks to form a heterogeneous complementary inverter circuit based on layered molybdenum disulfide and carbon nanotube (CNT) bundles. The fabricated CNT/MoS(2) inverter is composed of n-type molybdenum disulfide (MOS(2)) and p-type CNT transistors, with a high voltage gain of 1.3. The CNT channels are fabricated using directed assembly while the layered molybdenum disulfide channels are fabricated by mechanical exfoliation. This bottom-up fabrication approach for integrating various nanoscale elements with unique characteristics provides an alternative cost-effective methodology to complementary metal-oxide-semiconductors, laying the foundation for the realization of high performance logic circuits.

Dissimilatory antimonate reduction and production of antimony trioxide microcrystals by a novel microorganism.

Science.gov (United States)

Abin, Christopher A; Hollibaugh, James T

2014-01-01

Antimony (Sb) is a metalloid that has been exploited by humans since the beginning of modern civilization. The importance of Sb to such diverse industries as nanotechnology and health is underscored by the fact that it is currently the ninth-most mined metal worldwide. Although its toxicity mirrors that of its Group 15 neighbor arsenic, its environmental chemistry is very different, and, unlike arsenic, relatively little is known about the fate and transport of Sb, especially with regard to biologically mediated redox reactions. To further our understanding of the interactions between microorganisms and Sb, we have isolated a bacterium that is capable of using antimonate [Sb(V)] as a terminal electron acceptor for anaerobic respiration, resulting in the precipitation of antimonite [Sb(III)] as microcrystals of antimony trioxide. The bacterium, designated strain MLFW-2, is a sporulating member of a deeply branching lineage within the order Bacillales (phylum Firmicutes). This report provides the first unequivocal evidence that a bacterium is capable of conserving energy for growth and reproduction from the reduction of antimonate. Moreover, microbiological antimonate reduction may serve as a novel route for the production of antimony trioxide microcrystals of commercial significance to the nanotechnology industry.

Gaseous oxygen and hydrogen embrittlements of the uranium-10 weight % molybdenum alloy

International Nuclear Information System (INIS)

Corcos, Jean.

1979-07-01

The stress corrosion of an Uranium-10 weight % Molybdenum alloy in high purity gaseous oxygen and hydrogen was studied. Tests were performed with fracture-mechanic specimens, fatigue precracked and carried out in tension with a constant sustained load. The experimental procedure enabled to determine the S.C. morphology during the test, and its kinetics. Tests in gaseous oxygen were performed with p02=0.15 MPa from 0 0 C to 100 0 C, and at 20 0 C for p02=0.15, 0.15.10 -2 and 0.15.10 -4 MPa. Two kinetic laws are proposed. Cracking is transgranular with a quasi-clivage type, and occurs on the (1 1 1) planes of the matrix. Tests in gaseous hydrogen were performed with pH2=0.15 MPa from - 50 0 C to + 135 0 C; for all the tests, even those under no exterior load, there is a failure by S.C. and macroscopic hydruration occurs. We propose a kinetic law, which may display that the hydruration phenomenon rules the S.C. propagation. We have performed the identification of the hydride, as well as the study of the precipitation. These phenomena don't occur with pH2=0.15.10 -2 MPa. The embrittlement is thought to be due to a formation-failure cycle of an hydride precipitate at the crack tip [fr

Neutron scattering and models: molybdenum

International Nuclear Information System (INIS)

Smith, A.B.

1999-01-01

A comprehensive interpretation of the fast-neutron interaction with elemental and isotopic molybdenum at energies of le 30 MeV is given. New experimental elemental-scattering information over the incident energy range 4.5 r a rrow 10 MeV is presented. Spherical, vibrational and dispersive models are deduced and discussed, including isospin, energy-dependent and mass effects. The vibrational models are consistent with the ''Lane potential''. The importance of dispersion effects is noted. Dichotomies that exist in the literature are removed. The models are vehicles for fundamental physical investigations and for the provision of data for applied purposes. A ''regional'' molybdenum model is proposed. Finally, recommendations for future work are made

FY16 Status Report for the Uranium-Molybdenum Fuel Concept

International Nuclear Information System (INIS)

Bennett, Wendy D.; Doherty, Ann L.; Henager, Charles H.; Lavender, Curt A.; Montgomery, Robert O.; Omberg, Ronald P.; Smith, Mark T.; Webster, Ryan A.

2016-01-01

The Fuel Cycle Research and Development program of the Office of Nuclear Energy has implemented a program to develop a Uranium-Molybdenum metal fuel for light water reactors. Uranium-Molybdenum fuel has the potential to provide superior performance based on its thermo-physical properties. With sufficient development, it may be able to provide the Light Water Reactor industry with a melt-resistant, accident-tolerant fuel with improved safety response. The Pacific Northwest National Laboratory has been tasked with extrusion development and performing ex-reactor corrosion testing to characterize the performance of Uranium-Molybdenum fuel in both these areas. This report documents the results of the fiscal year 2016 effort to develop the Uranium-Molybdenum metal fuel concept for light water reactors.

FY16 Status Report for the Uranium-Molybdenum Fuel Concept

Energy Technology Data Exchange (ETDEWEB)

Bennett, Wendy D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Doherty, Ann L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Henager, Charles H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lavender, Curt A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Montgomery, Robert O. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Omberg, Ronald P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Smith, Mark T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Webster, Ryan A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-09-22

The Fuel Cycle Research and Development program of the Office of Nuclear Energy has implemented a program to develop a Uranium-Molybdenum metal fuel for light water reactors. Uranium-Molybdenum fuel has the potential to provide superior performance based on its thermo-physical properties. With sufficient development, it may be able to provide the Light Water Reactor industry with a melt-resistant, accident-tolerant fuel with improved safety response. The Pacific Northwest National Laboratory has been tasked with extrusion development and performing ex-reactor corrosion testing to characterize the performance of Uranium-Molybdenum fuel in both these areas. This report documents the results of the fiscal year 2016 effort to develop the Uranium-Molybdenum metal fuel concept for light water reactors.

A highly sensitive method for detection of molybdenum-containing proteins

International Nuclear Information System (INIS)

Kalakutskii, K.L.; Shvetsov, A.A.; Bursakov, S.A.; Letarov, A.V.; Zabolotnyi, A.I.; L'vov, N.P.

1992-01-01

A highly sensitive method for detection of molybdenum-containing proteins in gels after electrophoresis has been developed. The method involves in vitro labeling of the proteins with the radioactive isotope 185 W. The method used to detect molybdenum-accumulating proteins in lupine seeds, xanthine dehydrogenase and another molybdenum-containing protein in wheat, barley, and pea seedlings, and nitrate reductase and xanthine dehydrogenase in bacteroides from lupine nodules. Nitrogenase could not be detected by the method. 16 refs., 5 figs

Molybdenum(6) complexing with ethylenediaminedisuccinic acid from PMR spectroscopy data

International Nuclear Information System (INIS)

Larchenko, V.E.; Kovaleva, I.B.; Mitrofanova, N.D.; Martynenko, L.I.

1989-01-01

Methods of high resolution PMR spectroscopy and pH potentiometry are used to study molybdenum(6) complexing with ethylenediaminedisuccinic acid in aqueous solutions. It is shown that molybdenum(6) interacts with ethylenediaminedisuccinic acid in the narrow range of pH values 4.0-6.5, where MoO 3 H 2 L 2 - and MoO 3 HL 3- complexes with asymmetrical structure are formed. Composition and structure of molybdenum(6) ethylenediaminedisuccinates and ethylenediaminetetraacetates are compared

Kinetics of Sulfur, Vanadium and Nickel Removal from Basra Crude Oil Hydro Treating

Directory of Open Access Journals (Sweden)

Muzher M. Ibrahim

2013-05-01

Full Text Available     Basra crude oil was hydro treated in trickle–bed reactor using cobalt - molybdenum alumina as a Catalyst. The reaction range temperatures was598 – 648 k, while LHSV was 0.7 – 2 hr-1. The pressure and H2/Oil for all experiments keep constant at 3Mpa and 300 L/L respectively.    Desulphurization and demutualization kinetics were studied and found that the kinetics of sculpture removal is of first – order, and the kinetic of vanadium and nickel removal is of second – order.    Activation energy were calculated and their value are 24.03, 745.86, 63.90 KJ / mole, respectively for sculpture, vanadium, and nickel.

Comparison of early stages of precipitation in molybdenum-rich and molybdenum-poor maraging stainless steels

International Nuclear Information System (INIS)

Andersson, M.; Stiller, K.; Haettestrand, M.

2004-01-01

Full text: The precipitation hardening process in the molybdenum-rich Sandvik alloy 1RK91, with composition 12.8Cr-8.6Ni-2.3Mo-1.7Cu-1.2Ti-0.7Al (at. %), has previously been investigated with APFIM, energy-filtering transmission electron microscopy, and conventional transmission electron microscopy. The initial ageing response corresponds to Ni 3 (Al, Ti)-type precipitates, nucleating on copper clusters after only five minutes of ageing at 475 o C. After several hours of ageing, the precipitation hardening also includes contribution from molybdenum-rich quasicrystalline precipitates of icosahedral symmetry (R'), and another nickel-rich phase of type L1 0 . This complex precipitation behaviour, in combination with a resistance to coarsening of R', results in a continuous increase in material hardness for up to several hundred of hours of ageing. A significant difference in ageing response has been observed between the Sandvik alloy 1RK91 and molybdenum-poor alloy Carpenter 455 with composition 12.3Cr-7.9Ni-0.3Mo-1.8Cu-1.3Ti-0.1Al (at. %). During ageing at 475 o C, the hardness of Carpenter 455 saturates with a subsequent softening after just a few hours. The reason for the discrepancy in the ageing behaviour of the two steels is not well understood, since the precipitation reactions in Carpenter 455 have not been thoroughly surveyed. Therefore, the precipitation hardening process of Carpenter 455 has been studied, by using three-dimensional atom probe and energy-filtering transmission electron microscopy. The results have been compared with the precipitation hardening process of 1RK91 in order to explain the difference in ageing response of the two steels. Special interest has been devoted to understand the influence of molybdenum in the precipitation process of 1RK91. Refs 3 (author)

Manufacture of good-weldable low oxygen molybdenum by powder metallurgy

International Nuclear Information System (INIS)

Hiraoka, Yutaka; Okada, Masatoshi; Akiyama, Takashi; Yamafuchi, Yasuo.

1984-01-01

In general most of commercial molybdenum is produced by the powder metallurgy method and is utilized as a superior heat-resisting material in many fields. Moreover, molybdenum is expected to be used as the first-wall components of JT-60 (JAERI Tokamak-60). However, one of major problems on molybdenum, particularly on powder metallurgy molybdenum, is that any sound welded joint is hard to be obtainable. In many cases weld pores are formed on welding and, therefore, ductility of the welded joint is severely degraded. The object of the present work is to get a sound welded joint without any weld pores by reducing impurity levels in the material. The materials were produced by modifying one or several parts in the ordinary manufacturing process of powder metallurgy molybdenum. Oxygen, nitrogen, carbon and other principal metallic impurities were chemically analysed. The above materials were then subjected to electron-beam-welding by using a melt-run technique, and the soundness of the welded joints was examined by optical microscopy. (author)

Ion exchange resin fouling of molybdenum in recovery uranium processess

International Nuclear Information System (INIS)

Zhang Guowei; Zhao Guirong

1990-09-01

The relationship between anion exchange resin fouling and molybdic acid polymerization was studied. By using potentiometer titration and laser-Raman spectroscopy the relationship of molybdic acid polymerization and the pH value of solution or the molybdenum concentration was determined. It was shown that as the concentration of initial molybdenum in solution decreases from 0.2 mol/L to 0.5 mmol/L, the pH value of starting polymerization decreased from 6.5 to 4.5. The experimental results show that the fouling of 201 x 7 resin in the acidic solution is mainly caused by the adsorbing of Mo 3 O 26 4- ion and occupying the exchange radical site of the resin. Under the leaching conditions the molybdenum and phosphate existing in the leaching liquor can form 12-molybdo-phosphate ion. It also leads to resin fouling. The molybdenum on the fouled resin can synergically be desorbed by mixed desorbents containing ammonium hydroxide and ammonium sulfate. The desorbed resin can be used for uranium adsorption and the desorbed molybdenum can be recovered by ion exchange method

Molybdenum/alkali metal/ethylene glycol complexes useful as epoxidation catalysts

International Nuclear Information System (INIS)

Marquis, E.T.; Sanderson, J.R.; Keating, K.P.

1987-01-01

This patent describes a clear, storage stable solution of a molybdenum/alkali metal/ethylene glycol complex in ethylene glycol made by the process comprising: reacting at an elevated temperature between about 25 0 and 150 0 C a solid ammonium molybdate or a hydrate thereof and a solid alkali metal molybdate or a hydrate thereof with ethylene glycol, such that the ratio of moles of ethylene glycol to total gram atoms of molybdenum in the molybdates ranges from about 7:10 to 10:1, and the ratio of gram atoms of molybdenum in the ammonium molybdate or hydrate thereof to gram atoms of molybdenum in the alkali metal molybdate is from about 1:1 to about 20:1 to thereby provide a reaction product composed of a solution of an alkali metal-containing complex of molybdenum, alkali metal and ethylene glycol and by-products, including water, in the ethylene glycol and subsequently stripping the solution at a reduced pressure to remove from about 5 to about 25% of the reaction product, as distillate, to thereby provide a storage stable solution of the complex in the ethylene glycol having a molybdenum content of about 6 wt. % to about 20 wt. %, a water concentration of about 0.1 wt. % to about 6 wt. % and an acid number of more than about 60

Modification of molybdenum disulfide in methanol solvent for hydrogen evolution reaction

Science.gov (United States)

Niyitanga, Theophile; Jeong, Hae Kyung

2018-05-01

Molybdenum disulfide is a promising catalyst to replace the expensive platinum as an electrocatalyst but needs to be modified to present excellent electrocatalytic properties. Herein, we successfully modify molybdenum disulfide in methanol solvent for hydrogen evolution reaction by using a simple hydrothermal method. Overpotential reduced to -0.6 V from -1.5 V, and energy band gap decreased from 1.73 eV to 1.58 eV after the modification. The modified molybdenum disulfide also demonstrated lower resistance (42 Ω) at high frequency (1000 kHz) compared with that (240 Ω) of the precursor, showing that conductivity of the modified molybdenum disulfide has improved.

Fracture toughness of 6.4 mm (0.25 inch) Arc-Cast molybdenum and molybdenum-TZM plate at room temperature and 300 oC

International Nuclear Information System (INIS)

Shields, J.A. jr.; Lipetzky, P.; Mueller, A.J.

2001-01-01

The fracture toughness of 6.4 mm (0.25 inch) low carbon arc-cast (LCAC) molybdenum and arc-cast molybdenum-TZM alloy plate were measured at room temperature and 300 o C using compact tension specimens. The effect of crack plane orientation (longitudinal vs. transverse) and annealing practice (stress-relieved vs. recrystallized) were evaluated. Depending upon the test temperature either a standard K IC or a J-integral analysis was used to obtain the toughness value. At room temperature, regardless of alloy, orientation, or microstructure, fracture toughness values between 15 and 22 MPa m 1/2 (14 and 20 ksi in 1/2 ) were measured. These K IC values were consistent with measurements by other authors. Increasing temperature improves the toughness, due to the fact that one takes advantage of the ductile-brittle transition behavior of molybdenum. At 300 o C, the fracture toughness of recrystallized LCAC and arc-cast TZM molybdenum were also similar at approximately 64 MPa m 1/2 (58 ksi in 1/2 ). In the stress-relieved condition, however, the toughness of arc-cast TZM (91 MPa m 1/2 / 83 ksi in 1/2 ) was higher than that of the LCAC molybdenum (74 MPa m 1/2 / 67 ksi in 1/2 ). (author)

A study on the kinetics of hydrogen reduction of molybdenum disulphide powders

Energy Technology Data Exchange (ETDEWEB)

Mehdi Afsahi, M. [Amirkabir University of Technology, Department of Chemical Engineering, Tehran 15914 (Iran, Islamic Republic of); University of Cambridge, Department of Materials Sciences and Metallurgy, Cambridge CB2 3QZ (United Kingdom)], E-mail: mma50@cam.ac.uk; Sohrabi, Morteza [Amirkabir University of Technology, Department of Chemical Engineering, Tehran 15914 (Iran, Islamic Republic of); Vasant Kumar, R. [University of Cambridge, Department of Materials Sciences and Metallurgy, Cambridge CB2 3QZ (United Kingdom); Ale Ebrahim, Habib [Amirkabir University of Technology, Department of Chemical Engineering, Tehran 15914 (Iran, Islamic Republic of)

2008-07-10

In order to achieve direct reduction of molybdenite in presence of a sulphur scavenger such as CaO such that SO{sub 2} emission is completely avoided, it is important to maximise the rate of the partial reaction involving molybdenite and hydrogen (without lime) given the low thermodynamic driving force for this reaction. Accordingly, reaction of molybdenum disulphide powders with hydrogen was investigated by thermogravimetric method. Effect of temperature and concentration on the reaction rate was studied under such conditions that resistance to mass transfer arising from external film, between particles and intra-grain was negligible. The operating temperature ranged between 973 and 1173 K while the hydrogen concentration was varied between 30 and 100%. The experimental data obtained under the above conditions were analyzed by applying 'the shrinking unreacted core model'. The reduction reaction was found to be first order with respect to the gaseous reactant. Pre-exponential factor and activation energy have been determined to be 3.91 x 10{sup 3} cm min{sup -1} and 139.0 kJ mol{sup -1}, respectively. Activation energy obtained from a fitted model, agreed well with the values determined from the model-free methods using isothermal measurements.

Influence of Chromium and Molybdenum on the Corrosion of Nickel Based Alloys

International Nuclear Information System (INIS)

Hayes, J R; Gray, J; Szmodis, A W; Orme, C A

2005-01-01

The addition of chromium and molybdenum to nickel creates alloys with exceptional corrosion resistance in a diverse range of environments. This study examines the complementary roles of Cr and Mo in Ni alloy passivation. Four nickel alloys with varying amounts of chromium and molybdenum were studied in 1 molar salt solutions over a broad pH range. The passive corrosion and breakdown behavior of the alloys suggests that chromium is the primary element influencing general corrosion resistance. The breakdown potential was nearly independent of molybdenum content, while the repassivation potential is strongly dependant on the molybdenum content. This indicates that chromium plays a strong role in maintaining the passivity of the alloy, while molybdenum acts to stabilize the passive film after a localized breakdown event

Recovery of Tungsten and Molybdenum from Low-Grade Scheelite

Science.gov (United States)

Li, Yongli; Yang, Jinhong; Zhao, Zhongwei

2017-10-01

With most high-quality tungsten ores being exhausted, the enhancement of low-grade scheelite concentrates processing has attracted a great deal of attention. The objective of this study is to develop a method to maximize the recovery tungsten and molybdenum from a low-grade scheelite via a new acid leaching process followed by solvent extraction. Under optimal conditions (350 g/L H2SO4, 95°C, and 2 h), approximately 99.8% of tungsten and 98% of molybdenum were leached out. In the subsequent solvent extraction process, more than 99% of the tungsten and molybdenum were extracted with a co-extraction system (50% TBP, 30% HDEHP, and 10% 2-octanol in kerosene) using a three-stage cross-flow extraction. The raffinate can be recycled for the next leaching process after replenishing the H2SO4 to the initial value (approximately 350 g/L). Based on these results, a conceptual flowsheet is presented to recover tungsten and molybdenum from the low-grade scheelite.

Effect of drying method on properties of vanadium-molybdenum oxide catalysts

International Nuclear Information System (INIS)

Gorshkova, T.P.; Savchenko, L.A.; Tarasova, D.V.; Tret'yakov, Yu.D.; Olen'kova, I.P.; Nikoro, T.A.; Maksimov, N.G.

1981-01-01

Effect of drying method of molybdenum and vanadium salt solutions on physicochemical and catalytical properties of vanadium-molybdenum catalysts is studied. It is shown that the drying method of solutions determines the completeness of vanadium binding into oxide vanadium-molybdenum compounds and thus effects the activity and selectivity of catalysts in acrolein oxidation into acrylic acid. Besides the drying method determines the porous structure of catalysts [ru

Change of mechanical properties of molybdenum after chemical heat treatment

International Nuclear Information System (INIS)

Skuratov, L.P.; Yatsimirskij, V.K.; Kirillova, N.V.

1987-01-01

Gaseous media (argon, ammonia, nitrogen-hydrogen-ammonia mixture) are studied for their effect on mechanical characteristics of molybdenum at temperatures up to 1000 deg C. It is established that the highest hardening occurs when molybdenum is esposed in the nitrogen-hydrogen medium, while the highest lost of strength takes place in the ammonia medium. An increase of the ammonia concentration in nitrogen-hydrogen-ammonia mixture promotes regular increasing of the deformation rate. With ammonia concentration of 33.3% the gaseous mixture acts the same as pure ammonia. Change of physical-and-mechanical properties of molybdenum under the action of nitrogen-containing gaseous media is associated with formation of molybdenum compounds with nitrogen. During nitriding in ammonia an internal (volume) nitriding proceeds while in the medium of nitrogen-hydrogen mixture surface nitride layers form

Antimony trioxide-induced apoptosis is dependent on SEK1/JNK signaling.

Science.gov (United States)

Mann, Koren K; Davison, Kelly; Colombo, Myrian; Colosimo, April L; Diaz, Zuanel; Padovani, Alessandra M S; Guo, Qi; Scrivens, P James; Gao, Wenli; Mader, Sylvie; Miller, Wilson H

2006-01-05

Very little is known concerning the toxicity of antimony, despite its commercial use as a flame retardant and medical use as a treatment for parasitic infections. Our previous studies show that antimony trioxide (Sb(2)O(3)) induces growth inhibition in patient-derived acute promyelocytic leukemia (APL) cell lines, a disease in which a related metal, arsenic trioxide (As(2)O(3)), is used clinically. However, signaling pathways initiated by Sb(2)O(3) treatment remain undefined. Here, we show that Sb(2)O(3) treatment of APL cells is associated with increased apoptosis as well as differentiation markers. Sb(2)O(3)-induced reactive oxygen species (ROS) correlated with increased apoptosis. In addition, when we decreased the buffering capacity of the cell by depleting glutathione, ROS production and apoptosis was enhanced. Arsenic-resistant APL cells with increased glutathione levels exhibited increased cross-resistance to Sb(2)O(3). Based on studies implicating c-jun kinase (JNK) in the mediation of the response to As(2)O(3), we investigated the role for JNK in Sb(2)O(3)-induced apoptosis. Sb(2)O(3) activates JNK and its downstream target, AP-1. In fibroblasts with a genetic deletion in SEK1, an upstream regulator of JNK, Sb(2)O(3)-induced growth inhibition as well as JNK activation was decreased. These data suggest roles for ROS and the SEK1/JNK pathway in the cytotoxicity associated with Sb(2)O(3) exposure.

Simulation of uranium oxides reduction kinetics by hydrogen. Reactivities of germination and growth; Modelisation de la cinetique de reduction d`oxydes d`uranium par l`hydrogene. Reactivites de germination et de croissance

Energy Technology Data Exchange (ETDEWEB)

Brun, C

1997-12-04

The aim of this work is to simulate the reduction by hydrogen of the tri-uranium octo-oxide U{sub 3}O{sub 8} (obtained by uranium trioxide calcination) into uranium dioxide. The kinetics curves have been obtained by thermal gravimetric analysis, the hydrogen and steam pressures being defined. The geometrical modeling which has allowed to explain the trend of the kinetics curves and of the velocity curves is an anisotropic germination-growth modeling. The powder is supposed to be formed of spherical grains with the same radius. The germs of the new UO{sub 2} phase appear at the surface of the U{sub 3}O{sub 8} grains with a specific germination frequency. The growth reactivity is anisotropic and is very large in the tangential direction to the grains surface. Then, the uranium dioxide growths inside the grain and the limiting step is the grain surface. The variations of the growth reactivity and of the germination specific frequency in terms of the gases partial pressures and of the temperature have been explained by two different mechanisms. The limiting step of the growth mechanism is the desorption of water in the uranium dioxide surface. Concerning the germination mechanism the limiting step is a water desorption too but in the tri-uranium octo-oxide surface. The same geometrical modeling and the same germination and growth mechanisms have been applied to the reduction of a tri-uranium octo-oxide obtained by calcination of hydrated uranium trioxide. The values of the germination specific frequency of this solid are nevertheless weaker than those of the solid obtained by direct calcination of the uranium trioxide. (O.M.) 45 refs.

Reduction of molybdate to molybdenum blue by Klebsiella sp. strain hkeem.

Science.gov (United States)

Lim, H K; Syed, M A; Shukor, M Y

2012-06-01

A novel molybdate-reducing bacterium, tentatively identified as Klebsiella sp. strain hkeem and based on partial 16s rDNA gene sequencing and phylogenetic analysis, has been isolated. Strain hkeem produced 3 times more molybdenum blue than Serratia sp. strain Dr.Y8; the most potent Mo-reducing bacterium isolated to date. Molybdate was optimally reduced to molybdenum blue using 4.5 mM phosphate, 80 mM molybdate and using 1% (w/v) fructose as a carbon source. Molybdate reduction was optimum at 30 °C and at pH 7.3. The molybdenum blue produced from cellular reduction exhibited absorption spectrum with a maximum peak at 865 nm and a shoulder at 700 nm. Inhibitors of electron transport system such as antimycin A, rotenone, sodium azide, and potassium cyanide did not inhibit the molybdenum-reducing enzyme. Mercury, silver, and copper at 1 ppm inhibited molybdenum blue formation in whole cells of strain hkeem. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Low cycle fatigue behavior of titanium carbide coated molybdenum

International Nuclear Information System (INIS)

Nishi, Hiroshi; Oku, Tatsuo; Kodaira, Tsuneo; Kikuyama, Toshihiko

1985-09-01

Sintered molybdenum coated by TiC is used for the first wall such as a troidal fixed limiter and a magnetic limiter plate in JT-60, that is being operated at JAERI presently. This report describes the low cycle fatigue behavior of sintered molybdenum and the influence of TiC coating on fatigue strength. The low cycle fatigue test was conducted at room temperature and 500 0 C. The test results was also analyzed by fractographic observation, metallography and element analysis using EPMA. The low cycle fatigue strength of the molybdenum coated by TiC at 500 0 C is decreased compared with the one at room temperature. (author)

Removal and recovery of molybdenum from aqueous solutions by adsorption onto Surfactant-Modified coir pith, a lignocellulosic polymer

Energy Technology Data Exchange (ETDEWEB)

Namasivayam, Chinnaiya [Environmental Chemistry Division, Department of Environmental Sciences, Bharathiar University, Coimbatore (India); Sureshkumar, Molagoundanpalayam Venkatachalam [Department of Chemistry, PARK College of Engineering and Technology, Coimbatore (India)

2009-01-15

Coconut coir pith, a lignocellulosic polymer, is an unwanted by-product of the coir fiber industry. The pith was used as a biosorbent for the removal of Molybdenum(VI) after modification with a cationic surfactant, hexadecyltrimethylammonium bromide. The optimum pH for maximum adsorption of Mo(VI) was found to be 3.0. Langmuir, Freundlich and Dubinin Radushkevich isotherms were used to model the adsorption equilibrium data and the system was seen to follow all three isotherms. The Langmuir adsorption capacity of the biosorbent was found to be 57.5 mg g{sup -1}. Kinetic studies showed that the adsorption generally obeyed a second-order kinetic model. Desorption studies showed that the recovery of Mo(VI) from the spent adsorbent was feasible. The effect of foreign anions on the adsorption of Mo(VI) was also examined. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

Bioaccessibility of micron-sized powder particles of molybdenum metal, iron metal, molybdenum oxides and ferromolybdenum--Importance of surface oxides.

Science.gov (United States)

Mörsdorf, Alexander; Odnevall Wallinder, Inger; Hedberg, Yolanda

2015-08-01

The European chemical framework REACH requires that hazards and risks posed by chemicals, including alloys and metals, that are manufactured, imported or used in different products (substances or articles) are identified and proven safe for humans and the environment. Metals and alloys need hence to be investigated on their extent of released metals (bioaccessibility) in biologically relevant environments. Read-across from available studies may be used for similar materials. This study investigates the release of molybdenum and iron from powder particles of molybdenum metal (Mo), a ferromolybdenum alloy (FeMo), an iron metal powder (Fe), MoO2, and MoO3 in different synthetic body fluids of pH ranging from 1.5 to 7.4 and of different composition. Spectroscopic tools and cyclic voltammetry have been employed to characterize surface oxides, microscopy, light scattering and nitrogen absorption for particle characterization, and atomic absorption spectroscopy to quantify released amounts of metals. The release of molybdenum from the Mo powder generally increased with pH and was influenced by the fluid composition. The mixed iron and molybdenum surface oxide of the FeMo powder acted as a barrier both at acidic and weakly alkaline conditions. These findings underline the importance of the surface oxide characteristics for the bioaccessibility of metal alloys. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Arsenic speciation in saliva of acute promyelocytic leukemia patients undergoing arsenic trioxide treatment

OpenAIRE

Chen, Baowei; Cao, Fenglin; Yuan, Chungang; Lu, Xiufen; Shen, Shengwen; Zhou, Jin; Le, X. Chris

2013-01-01

Arsenic trioxide has been successfully used as a therapeutic in the treatment of acute promyelocytic leukemia (APL). Detailed monitoring of the therapeutic arsenic and its metabolites in various accessible specimens of APL patients can contribute to improving treatment efficacy and minimizing arsenic-induced side effects. This article focuses on the determination of arsenic species in saliva samples from APL patients undergoing arsenic treatment. Saliva samples were collected from nine APL pa...

Molybdenum peroxo complex. Structure and thermal behavior

Energy Technology Data Exchange (ETDEWEB)

Segawa, Koichi; Ooga, Katsumi; Kurusu, Yasuhiko

1984-10-01

The molybdenum peroxide (Mo-y) prepared by oxidation of molybdenum metal with hydrogen peroxide has been studied to determine its structure and thermal behavior. Temperature programmed decomposition has been used to study the thermal stability of Mo-y. Two distinct peaks, I and II, of decomposition processes are discernible in Mo-y. Peak I corresponds to the elimination of water of crystallization and peak II to the decomposition of a peroxide ion of Mo-y. IR and UV examinations support the results of the thermal analysis. The IR band at 931 cm/sup -1/ and the UV band at 381 nm show the same thermal behavior. Both bands are attributable to the peroxide ion of Mo-y. Spectroscopic studies show that Mo-y has the tetrahedral coordination derived from the single molybdenum complex, which has double bond oxygens attached to Mo atom and has a symmetric type of peroxide ion with one water of crystallization.

Production of Molybdenum-99 using Neutron Capture Methods

Energy Technology Data Exchange (ETDEWEB)

Toth, James J; Greenwood, Lawrence R; Soderquist, Chuck Z; Wittman, Richard S; Pierson, Bruce D; Burns, Kimberly A; Lavender, Curt A; Painter, Chad L; Love, Edward F; Wall, Donald E

2011-01-01

Pacific Northwest National Laboratory (PNNL), operated by Battelle, has identified a reference process for the production of molybdenum-99 (99Mo) for use in a chromatographic generator to separate the daughter product, technetium-99m (99mTc). The reference process uses the neutron capture reaction of natural or enriched molybdenum oxide via the reaction 98Mo(n,γ)99Mo. The irradiated molybdenum is dissolved in an alkaline solution, whereby the molybdenum, dissolved as the molybdate anion, is loaded on a proprietary ion exchange material in the chromatographic generator. The approach of this investigation is to provide a systematic collection of technologies to make the neutron capture method for Mo-99 production economically viable. This approach would result in the development of a technetium Tc99m generator and a new type of target. The target is comprised of molybdenum, either natural or enriched, and is tailored to the design of currently operating U.S. research reactors. The systematic collection of technologies requires evaluation of new metallurgical methods to produce the target, evaluation of target geometries tailored to research reactors, and chemical methods to dissolve the irradiated target materials for use in a chromatographic generator. A Technical specification for testing the target and neutron capture method in a research reactor is also required. This report includes identification of research and demonstration activities needed to enable deployment of neutron capture production method, including irradiations of prototypic targets, chemical processing of irradiated targets, and loading and extraction tests of Mo99 and Tc99m on the sorbent material in a prototypic generator design. The prototypical generator design is based on the proprietary method and systems for isotope product generation. The proprietary methods and systems described in this report are clearly delineated with footnotes. Ultimately, the Tc-99m generator solution provided by

Reactions of ethyl diazoacetate catalyzed by methylrhenium trioxide

Energy Technology Data Exchange (ETDEWEB)

Zhu, Z.; Espenson, H. [Iowa State Univ., Ames, IA (United States)

1995-11-03

Methylrhenium trioxide (CH{sub 3}ReO{sub 3} or MTO) has found wise use in catalysis, including the epoxidation and metathesis of olefins, aldehyde olefination, and oxygen transfer. Extensive reports have now appeared in the area of MTO-catalyzed substrate oxidations with hydrogen peroxide. Certain catalytic applications of MTO for organic reactions that do not utilize peroxide have now been realized. In particular, a catalytic amount of MTO with ethyl diazoacetate (EDA) will convert aromatic imines to aziridines and convert aldehydes and ketones to epoxides. The aziridine preparation proceeds in high yields under anaerobic conditions more conveniently than with existing methods. Compounds with a three-membered heterocyclic ring can be obtained with the EDA/MTO catalytic system. Aromatic imines undergo cycloaddition reactions to give aziridines under mild conditions.

Extraction of molybdenum with TBP-dodecane mixture in nitric medium. Application to uranium refining

International Nuclear Information System (INIS)

Donnet, Louis

1993-01-01

Uranium ores may contain high quantities of molybdenum which represents an undesirable impurity in the uranium conversion process. Thus it is necessary to check carefully its extraction and its stripping during the purification step. The purpose of this study was to investigate the molybdenum behaviour during this step. We have developed a radiochemical method for the determination of the molybdenum concentration in each phase. This method used gamma radiation of technetium 99m issued from molybdenum 99 disintegration. After a systematic study of all the extraction parameters, we have proposed mechanisms accounting for molybdenum extraction and we have calculated the constants for the different equilibria. In particular, we have furnished new data concerning the extraction of polymerised molybdenum species with tri butyl phosphate. We have also determined the polymerization constants of molybdenum in the aqueous phase. The influence of uranium and phosphate ions on the molybdenum behaviour during the extraction and stripping has been investigated. We have shown that the extraction of molybdenum was not modified by uranium but improved in the presence of phosphate ions. In the general case, we have shown that uranium, phosphate ions and the ageing of the solvent have an unfavourable effect on stripping. We have explained this result by the evolution of the complex in the organic phase to an un-stripped polymeric form. In conclusion, our study has allowed to explain the behaviour of molybdenum during the purification process, and the role of impurities present in the industrial solutions. It would serve as a guide to improve the exploitation for a better molybdenum-uranium separation. (author) [fr

Tetrathionate reductase of Salmonella thyphimurium: a molybdenum containing enzyme

International Nuclear Information System (INIS)

Hinojosa-Leon, M.; Dubourdieu, M.; Sanchez-Crispin, J.A.; Chippaux, M.

1986-01-01

Use of radioactive molybdenum demonstrates that the tetrathionate reductase of Salmonella typhimurium is a molydenum containing enzyme. It is proposed that this enzyme shares with other molybdo-proteins, such as nitrate reductase, a common molybdenum containing cofactor the defect of which leads to the loss of the tetrathionate reductase and nitrate reductase activities

Potentiometric titrations of molybdenum and vanadium in aqueous and mixed so lvents

International Nuclear Information System (INIS)

Das, S.K.; Dhaneshwar, R.G.

1990-01-01

Potentiometric titration method was developed for molybdenum, employing different electrode systems. Molybdenum(VI) is reduced to molybdenum(V) by ferrous solution in presence of phosphoric acid and then titrated with potassium dichromate. It was found that ferrous concentration should be five times more than molybdenum and phosphoric acid should be 1.0 ml for 0.1N titration and 0.5 ml for lower concentration titrations. The method is also applicable to vanadium titrations. Employing Au/SCE and Pt/SCE systems, it was observed that generally curve heights obtained for platinum electrode are higher than those for gold electrode. Also for both the electrode systems, the curve heights for vanadium titrations were found to be more than those for molybdenum. Lower limits of titrations for Au/SCE system are 0.01N for molybdenum and 0.0001N for vanadium, whereas for Pt/SCE system, the lower limits obtained were 0.01N for both molybdenum and vanadium titrations. In order to improve the sensitivities of the method, the bimetallic electrode systems Au/Pt and Pt/Au were employed. Au/Pt system was found to give better results than Pt/Au systems. Addition of organic solvent was found to have beneficial effects for titrations of 0.001N and below. Methanol was found to be a better solvent than ethanol. Molybdenum titrations, at 0.0001N level could be performed in methanol with Au/Pt system, which is to b e generally preferred than Pt/Au system. (author). 7 refs., 3 tabs

Kinetics of the process of formation and high-temperature oxidation of electrospark coatings on steel

International Nuclear Information System (INIS)

Verkhoturov, A.D.; Chiplik, V.N.; Egorov, F.F.; Lavrenko, V.A.; Podchernyaeva, I.A.; Shemet, V.Z.

1986-01-01

This work is a study of the kinetics of formation and of the heat resistance of electrospark coatings based on the composite TiB 2 -Mo with varying molybdenum content. In the process of electrospark alloying they measured the specific erosion of the anode and the increase in weight of the cathode with an accuracy not worse than 5%. Electrospark coatings of TiB 2 -Mo on steel 45 are marked by improved scaling resistance at temperatures above 900 C. Their scaling resistance and also the effectiveness of the process of electrospark alloying increase with increasing content of the phase B-MoB in the coating because molybdenum borate forms during its high-temperature oxidation. Illustrations and table are included

Molybdenum-cofactor deficiency: an easily missed cause of neonatal convulsions

NARCIS (Netherlands)

Slot, H. M.; Overweg-Plandsoen, W. C.; Bakker, H. D.; Abeling, N. G.; Tamminga, P.; Barth, P. G.; van Gennip, A. H.

1993-01-01

Intractable seizures in the neonatal period may be caused by molybdenum-cofactor deficiency, an inborn error which combines the deficiencies of sulphite oxidase and xanthine dehydrogenase. The neurological symptoms of molybdenum cofactor and isolated sulphite oxidase deficiencies are identical. Two

Pulp-Capping with Mineral Trioxide Aggregate

Directory of Open Access Journals (Sweden)

Peycheva Kalina

2015-11-01

Full Text Available There are two considerations for direct pulp capping - accidental mechanical pulp exposure and exposure caused by caries. Mineral trioxide aggregate (MTA was used as pulp-capping material to preserve the vitality of the pulpal tissues. Follow-up examinations revealed that treatment was successful in preserving pulpal vitality and continued development of the tooth. On the basis of available information, it appears that MTA is the material of choice for some clinical applications. Material and methods: Cases 18 - 8 teeth with grey MTA, 10 teeth with white MTA; diagnose: Pulpitis chronica ulcerosa, Electro pulpal test (EOD - 30-35 μA, pre-clinical X-ray - without changes in the structures, follow ups for 4 years. Successful treatments: without clinical symptoms and changes in the X-rays: 5 teeth with grey MTA, 8 teeth with white MTA for period of 4 years. Unsuccessful treatments: Clinical symptoms and sometimes changes in the X-ray: 3 with grey MTA, 2 with white MTA. MTA is an appropriate material for pulp-capping and follow-up examinations revealed that the treatment was successful in preserving pulpal vitality.

Spectrographic analysis of uranium-molybdenum alloys

International Nuclear Information System (INIS)

Roca, M.

1967-01-01

A spectrographic method of analysis has been developed for uranium-molybdenum alloys containing up to 10 % Mo. The carrier distillation technique, with gallium oxide and graphite as carriers, is used for the semiquantitative determination of Al, Cr, Fe, Ni and Si, involving the conversion of the samples into oxides. As a consequence of the study of the influence of the molybdenum on the line intensities, it is useful to prepare only one set of standards with 0,6 % MoO 3 . Total burning excitation is used for calcium, employing two sets of standards with 0,6 and 7.5 MoO 3 . (Author) 5 refs

The Effect of Molybdenum Fertilization on Arachis Glabrata Biomass ...

African Journals Online (AJOL)

The effect of molybdenum fertilization on biomass and the number of nodules of Arachis glabrata was assessed at the Teaching and Research Farm of the University of Dschang in 2011 at different periods of mowing. A factorial design comparing four doses of molybdenum as ammonium molybdate (0, 0.75, 1.5 and 2.25 ...

Flexible Molybdenum Electrodes towards Designing Affinity Based Protein Biosensors.

Science.gov (United States)

Kamakoti, Vikramshankar; Panneer Selvam, Anjan; Radha Shanmugam, Nandhinee; Muthukumar, Sriram; Prasad, Shalini

2016-07-18

Molybdenum electrode based flexible biosensor on porous polyamide substrates has been fabricated and tested for its functionality as a protein affinity based biosensor. The biosensor performance was evaluated using a key cardiac biomarker; cardiac Troponin-I (cTnI). Molybdenum is a transition metal and demonstrates electrochemical behavior upon interaction with an electrolyte. We have leveraged this property of molybdenum for designing an affinity based biosensor using electrochemical impedance spectroscopy. We have evaluated the feasibility of detection of cTnI in phosphate-buffered saline (PBS) and human serum (HS) by measuring impedance changes over a frequency window from 100 mHz to 1 MHz. Increasing changes to the measured impedance was correlated to the increased dose of cTnI molecules binding to the cTnI antibody functionalized molybdenum surface. We achieved cTnI detection limit of 10 pg/mL in PBS and 1 ng/mL in HS medium. The use of flexible substrates for designing the biosensor demonstrates promise for integration with a large-scale batch manufacturing process.

Study on creep-fatigue evaluation of chrome-molybdenum steel

International Nuclear Information System (INIS)

Aoto, Kazumi; Wada, Yusaku

1993-01-01

Though chrome-molybdenum steel has quite different basic material properties from austenitic stainless steel, the life fraction rule based on an advanced ductility exhaustion theory proposed for SUS304 is able to give proper prediction for creep-fatigue life of chrome-molybdenum steel. The applicability of the present evaluation method to chrome-molybdenum steel is validated by both mechanical study and micro-structural observation. The mechanism of creep-fatigue failure of Mod.9Cr-1Mo(NT) is one of the most controversial subjects among researchers. However, it is clarified in this report that creep-fatigue damage of this material under actual loading conditions is dominated by creep-cavitation of grain boundaries as same way as that of austenitic stainless steel. Furthermore, for the life reduction of low cycle fatigue of chrome-molybdenum steel with compression-side strain hold, both effects of mean stress and oxide-wedge are denied and it is insisted that the acceleration of fatigue-crack propagation is occurred by oxide-progress location and its thickness. (author)

Electron accelerator-based production of molybdenum-99: Bremsstrahlung and photoneutron generation from molybdenum vs. tungsten

Energy Technology Data Exchange (ETDEWEB)

Tsechanski, A. [Ben-Gurion University of the Negev, Department of Nuclear Engineering, P.O. Box 653, Beer-Sheva 84105 (Israel); Bielajew, A.F. [Department of Nuclear Engineering and Radiological Sciences, The University of Michigan, 2355 Bonisteel Boulevard, Ann Arbor, MI 48109 (United States); Archambault, J.P.; Mainegra-Hing, E. [National Research Council of Canada, Ionizing Radiation Standards Laboratory, Ottawa, ON K1A 0R6 (Canada)

2016-01-01

A new “one-stage” approach for production of {sup 99}Mo and other radioisotopes by means of an electron linear accelerator is described. It is based on using a molybdenum target both as a bremsstrahlung converter and as a radioisotope producing target for the production of {sup 99}Mo via the photoneutron reaction {sup 100}Mo(γ,n){sup 99}Mo. Bremsstrahlung characteristics, such as bremsstrahlung efficiency, angular distribution, and energy deposition for molybdenum targets were obtained by means of the EGSnrc Monte Carlo simulation code system. As a result of our simulations, it is concluded that a 60 MeV electron beam incident on a thick Mo target will have greater bremsstrahlung efficiency than the same thickness (in units of r{sub 0}) W target, for target thickness z > 1.84r{sub 0}, where r{sub 0} is the electron range. A 50 MeV electron beam incident on a Mo target will result in greater bremsstrahlung efficiency than the same thickness W target (in units of r{sub 0}) for target thickness case: z ⩾ 2.0r{sub 0}. It is shown for the one-stage approach with thicknesses of (1.84–2.0)r{sub 0}, that the {sup 99}Mo-production bremsstrahlung efficiency of a molybdenum target is greater by ∼100% at 30 MeV and by ∼70% at 60 MeV compared to the values for tungsten of the same thickness (in units of the appropriate r{sub 0}) in the traditional two-stage approach (W converter and separate {sup 99}Mo producing target). This advantage of the one-stage approach arises from the fact that the bremsstrahlung produced is attenuated only once from attenuation in the molybdenum converter/target. In the traditional, two-stage approach, the bremsstrahlung generated in the W-converter/target is attenuated both in the converter in the {sup 99}Mo-producing molybdenum target. The photoneutron production yield of molybdenum and tantalum (as a substitute for tungsten) target was calculated by means of the MCNP5 transport code. On the basis of these data, the specific activity

The potential roles of lime and molybdenum on the growth, nitrogen ...

African Journals Online (AJOL)

STORAGESEVER

2010-04-26

Apr 26, 2010 ... and Molybdenum (Mo) are essential plant nutrients; whose role has been well ... interaction on different photosynthetic activities in P. vulgaris grown ..... concentrations of nickel, cadmium lead and molybdenum. J. Plant. Nutr.

Critical evaluation of molybdenum and its alloys for use in space reactor core heat pipes

International Nuclear Information System (INIS)

Lundberg, L.B.

1981-01-01

The choice of pure molybdenum as the prime candidate material for space reactor core heat pipes is examined, and the advantages and disadvantages of this material are brought into focus. Even though pure molybdenum heat pipes have been built and tested, this metal's high ductile-brittle transition temperature and modest creep strength place significant design restrictions on a core heat pipe made from it. Molybdenum alloys are examined with regard to their promise as potential replacements for pure molybdenum. The properties of TZM and molybdenum-rhenium alloys are examined, and it appears that Mo-Re alloys with 10 to 15 wt % rhenium offer the most advantage as an alternative to pure molybdenum in space reactor core heat pipes

Study of mechanoactivation of tungsten-molybdenum containing raw material in gas-jet mill

International Nuclear Information System (INIS)

Agnokov, T.Sh.; Gorobets, L.Zh.; Martynenko, V.P.; Fedorov, Yu.P.; Krakhmaleva, M.T.; Sokolova, L.A.

1988-01-01

Investigation is aimed at intensifying autoclave-soda leaching of tungsten-molybdenum-containing raw material. Connection of reactivity and physicochemical properties of crushed tungsten-molybdenum-containing products under different gas-jet crushing parameters is investigated. Optimal technological indices of hydrometallurgical reprocessing of tungsten-molybdenum-containing raw materials and products processed by gas-jet technique are given. The results obtained point out to perspectiveness of applying gas-jet technique of thermomechanical processing for intensifying and increasing the quality of tungsten- and molybdenum-containing raw materials and products of hydrometallurgical production

Recovering and recycling uranium used for production of molybdenum-99

Science.gov (United States)

Reilly, Sean Douglas; May, Iain; Copping, Roy; Dale, Gregory Edward

2017-12-12

A processes for recycling uranium that has been used for the production of molybdenum-99 involves irradiating a solution of uranium suitable for forming fission products including molybdenum-99, conditioning the irradiated solution to one suitable for inducing the formation of crystals of uranyl nitrate hydrates, then forming the crystals and a supernatant and then separating the crystals from the supernatant, thus using the crystals as a source of uranium for recycle. Molybdenum-99 is recovered from the supernatant using an adsorbent such as alumina. Another process involves irradiation of a solid target comprising uranium, forming an acidic solution from the irradiated target suitable for inducing the formation of crystals of uranyl nitrate hydrates, then forming the crystals and a supernatant and then separating the crystals from the supernatant, thus using the crystals as a source of uranium for recycle. Molybdenum-99 is recovered from the supernatant using an adsorbent such as alumina.

Sintering of cermets on the base of corundum and molybdenum

International Nuclear Information System (INIS)

Fedotov, A.V.

1987-01-01

Liquid-phase sintering of cermets has been studied to develop rational technology allowing to produce a dense material at lower temperatures. Molybdenum of the MPCh mark with the specific surface ranged from 1900 to 4000 cm 2 /g and the corundum powder of the VK-94-1 mark with the specific surface of 6000 cm 2 /g containing upto 10% of the glass-phase have been used as initial materials. It is shown that application of the VK-94-1 ceramics powder for molybdenum content cermets allows to decrease the temperature of dense material production (∼ upto 100 deg C). To produce dense materials, it is necessary to restrict the initial porosity of compaction and to correspond it to the sintering conditions. The increase of molybdenum dispersion allows to produce material with the more homogeneous structure, higher density and strength. Molybdenum presence decreases recrystallization of corundum crystals and causes structure production resistant to high-temperature heating

Electrical resistivity of sputtered molybdenum films

International Nuclear Information System (INIS)

Nagano, J.

1980-01-01

The electrical resistivity of r.f. sputtered molybdenum films of thickness 5-150 nm deposited on oxidized silicon substrates was resolved into the three electron scattering components: isotropic background scattering, scattering at grain boundaries and scattering at surfaces. It was concluded that the isotropic background scattering is almost equal to that of bulk molybdenum and is not influenced by sputtering and annealing conditions. When the film thickness is sufficient that surface scattering can be ignored, the decrease in film resistivity after annealing is caused by the decrease in scattering at the grain boundaries for zero bias sputtered films, and is caused by an increase of the grain diameter for r.f. bias sputtered films. (Auth.)

Arsenic trioxide: impact on the growth and differentiation of cancer cells and possible use in cancer therapy

Directory of Open Access Journals (Sweden)

Ewelina Hoffman

2013-08-01

Full Text Available Arsenic trioxide (As2O3 has recently been identified as an effective drug in different types of cancer therapy. It is a useful pharmacological agent in acute promyelocytic leukemia (APL treatment, especially the form that is resistant to conventional chemotherapy with all-trans retinoic acid (ATRA. What is more, laboratory data suggest that As2O3 is also active when it comes to several solid tumor cell lines. However, the mechanism of action is not fully understood. As2O3 in high doses triggers apoptosis, while in lower concentrations it induces partial differentiation. The As2O3 mechanism of action involves effects on mitochondrial transmembrane potential which lead to apoptosis. It also acts on the activity of JNK kinase, glutathione, caspases, NF-ĸB nuclear factor or pro- and antiapoptotic proteins. This publication presents the current knowledge about the influence of arsenic trioxide in cancer cells.

Dependence of fracture toughness of molybdenum laser welds on processing parameters and in-situ oxygen gettering

International Nuclear Information System (INIS)

Pope, L.E.; Jellison, J.L.

1980-01-01

Fracture toughness properties have been determined for laser welds in different grades of molybdenum. The fracture toughness of welds in sintered molybdenum was consistently less than the fracture toughness of welds in vacuum arc remelted molybdenum. These differences cannot be attributed to oxygen content, since the oxygen level was nominally the same for all grades of molybdenum examined in this program. Alloy additions of titanium by means of physically deposited coatings significantly improved the fracture toughness of welds in sintered molybdenum, whereas titanium additions to welds in vacuum arc remelted molybdenum decreased the fracture toughness slightly. Pulsed laser welds exhibited fine columnar structures and, in the case of sintered molybdenum, superior fracture toughness when compared with continuous wave laser welds. 6 figures, 3 tables

The behaviour of molybdenum dialkyldithiocarbamate friction modifier additives

International Nuclear Information System (INIS)

Graham, Jocelyn Claire Herries

2001-01-01

In recent years there has been growing concern to produce energy-efficient lubricated components and modem engine oil specifications require lubricants to demonstrate fuel efficiency in standardised engine tests. One important method of producing low friction and thus fuel-efficient lubricants is to use oil-soluble, molybdenum-containing, friction modifier additives. In optimal conditions these additives are able to produce very low friction coefficients, in the range 0.045 to 0.075 in boundary lubrication conditions. Very little is known about the chemical and physical mechanisms by which oil soluble molybdenum additives form low friction films in tribological contacts. Information about their activity could lead to optimal use of these additives in lubricants and, therefore, more efficient engine running. The work outlined in this thesis investigated the behaviour of oil-soluble molybdenum additives and showed that these additives were able to effectively reduce friction in the absence of other additives such as ZnDTP. Their activity was shown to be highly concentration and temperature dependent and was also found to be sensitive to the roughness of the contacting surfaces. Raman spectroscopy was used to analyse the chemical nature of molybdenum-containing reaction films and found that friction reduction indubitably arises from the local formation of platelets (diameter 30-50 nm) of MoS 2 . The formation of MoS 2 -rich films was found to occur only during direct asperity-asperity rubbing of the contacting surfaces (this type of contact being especially prevalent in pure sliding contacts). At elevated temperatures and in the presence of oxidising gases the consumption of MoDTC was monitored. MoDTC concentration dropped until the total value fell below a critical level to reduce friction. The study showed that decay rate of molybdenum-containing species was reduced by the addition of peroxide-decomposing antioxidants. (author)

Preparation of single phase molybdenum boride

International Nuclear Information System (INIS)

Camurlu, Hasan Erdem

2011-01-01

Highlights: → Formation of Mo and a mixture of molybdenum boride phases take place in preparation of molybdenum borides. → It is intricate to prepare single phase molybdenum borides. → Formation of single phase MoB from MoO 3 + B 2 O 3 + Mg mixtures has not been reported previously. → Single phase MoB was successfully prepared through a combination of mechanochemical synthesis and annealing process. - Abstract: The formation of MoB through volume combustion synthesis (VCS), and through mechanochemical synthesis (MCS) followed by annealing has been investigated. MoO 3 , B 2 O 3 and Mg were used as reactants while MgO and NaCl were introduced as diluents. Products were leached in dilute HCl solution and were subjected to X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) examinations. Mo was the major phase component in the VCS products under all the experimental conditions. Mo 2 B, MoB, MoB 2 and Mo 2 B 5 were found as minor phases. Products of MCS contained a mixture of Mo 2 B, MoB, MoB 2 and Mo. After annealing the MCS product at 1400 deg. C for 3 h, single phase α-MoB was obtained.

Application of anion-exchange techniques to the determination of traces of molybdenum in sea-water

International Nuclear Information System (INIS)

Kiriyama, T.; Kuroda, R.

1984-01-01

A combined ion-exchange spectrophotometric method has been developed for the determination of molybdenum in sea-water. Molybdenum is sorbed strongly on Amberlite CG 400 (Cl - ) at pH 3 from sea-water containing ascorbic acid and is easily eluted with 6 M nitric acid. Molybdenum in the effluent can be determined spectrophotometrically with potassium thiocyanate and stannous chloride. The combined method allows selective and sensitive determination of traces of molybdenum in sea-water. The precision of the method is 2% at a molybdenum level of approx. 10 μg/l. (author)

Kinetics of oxidation of the alloy-MR-47VP with nitrogen dioxide

International Nuclear Information System (INIS)

Vasil'eva, A.G.; Rakova, N.N.; Vladimirskaya, I.N.; Kabanova, O.V.; Miklyaev, A.D.

1978-01-01

The kinetic dependences of oxidation of MR-47VP grade molybdenum-rhenium alloy with nitrogen dioxide have been examined within the temperature range of 350 to 550 deg C. It has been shown that the processes take place in the transition region. The specific oxidation rate of the alloy with the nitrogen dioxide is but small, and it is comparable as to its value with the specific rate of its oxidation in oxygen under identical conditions

Astrocyte dysfunction following molybdenum-associated purine loading could initiate Parkinson's disease with dementia.

Science.gov (United States)

Bourke, Christopher A

2018-01-01

Sporadic or idiopathic Parkinson's disease is a movement disorder with a worldwide distribution, a long pre-clinical latent period and a frequent association with dementia. The combination of molybdenum deficiency and purine ingestion could explain the movement disorder, the distribution, the latent period and the dementia association. Recent studies in sheep have shown that molybdenum deficiency enables some dietary purines to accumulate in the central nervous system. This causes astrocyte dysfunction, altered neuromodulation and eventually irreversible central nervous system disease. Humans and sheep share the ability to salvage purines and this ability places humans at risk when they ingest xanthosine, inosine, adenosine and guanosine. Adenosine ingestion in molybdenum-deficient humans will lead to adenosine loading and potentially a disturbance to the A2a adenosine receptors in the nigro-striatum. This could result in Parkinson's disease. Guanosine ingestion in molybdenum-deficient humans will lead to guanosine loading and potentially a disturbance to the guanosine receptors in the hippocampus, amygdala and ventral striatum. This could result in dementia. The molybdenum content of the average daily diet in the United States is 0.07 ppm and in the United Kingdom 0.04 ppm. Central nervous system disease occurs in sheep at <0.04 ppm. Consistent with the role proposed for molybdenum deficiency in Parkinson's disease is the observation that affected individuals have elevated sulfur amino acid levels, depressed sulfate levels, and depressed uric acid levels. Likewise the geographical distribution of Parkinson's dementia complex on Guam corresponds with the distribution of molybdenum-deficient soils hence molybdenum-deficient food gardens on that island.

The use of xylenol orange (XO) reagent in molybdenum (MO) analysis

International Nuclear Information System (INIS)

Yusuf Nampira; Dian Anggraini

2012-01-01

The use of xylenol orange (XO) reagent in the analysis of Molybdenum (Mo) by spectrophotometry have been studied. The aim of this activity is to study the ability of xylenol orange to form a compound of molybdenum-xylenol orange complex to be analyzed by spectrophotometry. Some factors influencing the forming of the complex compound, for instance pH, time, comparison of XO/MO and the amount of Mo, are also studied. The materials used in this research includes ammonium molybdate (NH 4 ) 6 Mo 7 O 24 .4H 2 O), 0,5% xylenol orange and buffer solution (pH 1,5). Measurement result indicates that molybdenum content can be determined by spectrophotometry method at a wavelength of 563,6 nm. The maximum absorbance reached at a ratio of Molybdenum/Xylenol orange 1:2. The concentration of Mo was determined by using law of Lambert Beer, which stayed in the range of 2 ppm to 4 ppm. The stability of complex compound of molybdenum xylenol orange was shorter than 5 minutes. This measurement result can be used as a parameter in the determination of Mo element with UV-VIS spectrophotometer. (author)

The adsorption of molybdenum(VI) onto activated carbon from acid solution

International Nuclear Information System (INIS)

De Wet, H.F.

1985-11-01

The adsorption of molybdenum(VI) onto activated carbon is dependent on which nuclides are present in the solution. In this study the adsorption of Mo(VI) onto activated carbon is examined as a function of two variables, namely: the total molybdenum concentration and the pH. The equilibration time, the influence of ionic strength and the reversibility of the system was also examined. A series of solutions of a specified molybdenum concentration were equilibrated with activated carbon. In these experiments the pH varied from 5,5 to 0,9 while the temperature and ionic strength remained constant. The solutions were analysed colorimetrically and the pH equilibrium of each was measured. The molybdenum concentration for the series of experiments varied from 5x10 -4 M to 2x10 -2 M. 61 refs., 39 figs., 38 tabs

Research of the technology of obtaining pure and disperse molybdenum disulfide from molybdenum concentrate

International Nuclear Information System (INIS)

Hovsepyan, A.H.; Israyelyan, S.M.

2009-01-01

The technology of obtaining pure and disperse molybdenum disulfide is worked out. The processes of refinement from the flotation reagents and deslimation by means of decantation, refinement of molybdenite concentrate from impurities by selective leaching methods are studied. The optimal regime of technological process is chosen

Influence of Soil Solution Salinity on Molybdenum Adsorption by Soils

Science.gov (United States)

Molybdenum (Mo) adsorption on five arid-zone soils from California was investigated as a function of equilibrium solution Mo concentration (0-30 mg L-1), solution pH (4-8), and electrical conductivity (EC = 0.3 or 8 dS m-1). Molybdenum adsorption decreased with increasing pH. An adsorption maximum...

Microstructures define melting of molybdenum at high pressures

Science.gov (United States)

Hrubiak, Rostislav; Meng, Yue; Shen, Guoyin

2017-03-01

High-pressure melting anchors the phase diagram of a material, revealing the effect of pressure on the breakdown of the ordering of atoms in the solid. An important case is molybdenum, which has long been speculated to undergo an exceptionally steep increase in melting temperature when compressed. On the other hand, previous experiments showed nearly constant melting temperature as a function of pressure, in large discrepancy with theoretical expectations. Here we report a high-slope melting curve in molybdenum by synchrotron X-ray diffraction analysis of crystalline microstructures, generated by heating and subsequently rapidly quenching samples in a laser-heated diamond anvil cell. Distinct microstructural changes, observed at pressures up to 130 gigapascals, appear exclusively after melting, thus offering a reliable melting criterion. In addition, our study reveals a previously unsuspected transition in molybdenum at high pressure and high temperature, which yields highly textured body-centred cubic nanograins above a transition temperature.

Recovery of uranium and molybdenum elements from gebel gattar raw material, eastern desert, Egypt. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

El-Hazek, N T; Mahdy, M A; Mahmoud, H M.K. [Nuclear Materials Authority, Cairo, (Egypt)

1996-03-01

G. Gatter uranium mineralizations are located along the faults and fracture zones crossing G.Gattar granitic pluton and long the contact of the pluton with the hammamat sediments. Also, molybdenum id presented in more than one mode of occurrence. The molybdenum mineralization treated in this work is the dessimenated type. The uranium and molybdenum raw material was subjected to series of leaching experiments including acid and alkaline agitation, alkaline percolation, and acid heap leaching techniques. Recovery of uranium and molybdenum was achieved by anion-exchange method followed by their elution by acidified sodium chloride. Uranium precipitation was performed in the form of ammonium diuranate (Yellow Cake). On the other hand molybdenum was precipitated in the form of molybdenum oxide. A tentative flowsheet for the extraction of both uranium and molybdenum is proposed and discussed. 13 figs., 3 tabs.

Recovery of uranium and molybdenum elements from gebel gattar raw material, eastern desert, Egypt. Vol. 3

International Nuclear Information System (INIS)

El-Hazek, N.T.; Mahdy, M.A.; Mahmoud, H.M.K.

1996-01-01

G. Gatter uranium mineralizations are located along the faults and fracture zones crossing G.Gattar granitic pluton and long the contact of the pluton with the hammamat sediments. Also, molybdenum id presented in more than one mode of occurrence. The molybdenum mineralization treated in this work is the dessimenated type. The uranium and molybdenum raw material was subjected to series of leaching experiments including acid and alkaline agitation, alkaline percolation, and acid heap leaching techniques. Recovery of uranium and molybdenum was achieved by anion-exchange method followed by their elution by acidified sodium chloride. Uranium precipitation was performed in the form of ammonium diuranate (Yellow Cake). On the other hand molybdenum was precipitated in the form of molybdenum oxide. A tentative flowsheet for the extraction of both uranium and molybdenum is proposed and discussed. 13 figs., 3 tabs

Active carbon supported molybdenum carbides for higher alcohols synthesis from syngas

DEFF Research Database (Denmark)

Wu, Qiongxiao; Chiarello, Gian Luca; Christensen, Jakob Munkholt

This work provides an investigation of the high pressure CO hydrogenation to higher alcohols on K2CO3 promoted active carbon supported molybdenum carbide. Both activity and selectivity to alcohols over supported molybdenum carbides increased significantly compared to bulk carbides in literatures...

Response of soybean plants to phosphorus, boron and molybdenum fertilization

International Nuclear Information System (INIS)

Abdel-Aziz, H. A.; Aly, M. E.

2012-12-01

A pot experiment was carried out to study the effect of added phosphorus levels (30. 60 kg p/fed) with the addition of boron at (2, 6 ppm) and molybdenum at (5, 10.ppm) and without addition beside the control the control on growth and mineral content and root nodules in soybean plants. The results indicated that the effect of phosphorus on the formation of nodules had a clear effect when added with boron, molybdenum and when boron added at a rate of 2 ppm in the absence of phosphorus led to increase in root nodules in each of the 5, 10 ppm led to increased formation of, naldetuss in of the alluvial and calcareous soil. The molybdenum, nitrogen and phosphorus uptake increased directly proportional to the result of increased rate of addition of phosphorus and molybdenum. While the uptake born may be added with the rate of increased concentration of 2 ppm, while when added at 6 ppm led tp increased absorption of boron in the calcareous soil, but led to a decrease in the alluvial soils. (Author)

Edge eigen-stress and eigen-displacement of armchair molybdenum disulfide nanoribbons

Energy Technology Data Exchange (ETDEWEB)

Wu, Quan; Li, Xi [Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), University of Science and Technology Beijing, Beijing 100083 (China); Volinsky, Alex A., E-mail: volinsky@usf.edu [Department of Mechanical Engineering, University of South Florida, Tampa, FL 33620 (United States); Su, Yanjing, E-mail: yjsu@ustb.edu.cn [Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), University of Science and Technology Beijing, Beijing 100083 (China)

2017-05-10

Edge effects on mechanical properties of armchair molybdenum disulfide nanoribbons were investigated using first principles calculations. The edge eigen-stress model was applied to explain the relaxation process of forming molybdenum disulfide nanoribbon. Edge effects on surface atoms fluctuation degree were obtained from each fully relaxed nanoribbon with different width. Changes of the relaxed armchair molybdenum disulfide nanoribbons structure can be expressed using hexagonal perimeters pattern. Based on the thickness change, relaxed armchair molybdenum disulfide nanoribbons tensile/compression tests were simulated, providing intrinsic edge elastic parameters, such as eigen-stress, Young's modulus and Poisson's ratio. - Highlights: • Edge effects on mechanical properties of armchair MoS{sub 2} nanoribbons were investigated. • Structure changes of different width armchair MoS{sub 2} nanoribbons were obtained. • Tensile/compressive tests were conducted to determine elastic constants. • Mechanical properties are compared for two and three dimensional conditions.

A New Method for Low-Temperature Decomposition of Chromites and Dichromium Trioxide using Bromic Acid Evaluated by Chromium Isotope Measurements

Czech Academy of Sciences Publication Activity Database

Chrastný, V.; Rohovec, Jan; Čadková, E.; Pašava, J.; Farkaš, J.; Novák, M.

2014-01-01

Roč. 38, č. 1 (2014), s. 103-110 ISSN 1639-4488 Institutional support: RVO:67985831 Keywords : chromites * dichromium trioxide * decomposition * chromium isotopes * bromic acid Subject RIV: DD - Geochemistry Impact factor: 3.792, year: 2013

Recovery of uranium from sulphate solutions containing molybdenum

International Nuclear Information System (INIS)

Weir, D.R.; Genik-Sas-Berezowsky, R.M.

1983-01-01

A process for recovering uranium from a sulphate solution containing dissolved uranium and molybdenum includes reacting the solution with ammonia (pH 8 to 10), the pH of the original solution must not exceed 5.5 and after the addition of ammonia the pH must not be in the vicinity of 7 for a significant time. The resultant uranium precipitate is relatively uncontaminated by molybdenum. The precipitate is then separated from the remaining solution while the pH is maintained within the stated range

Nanograin formation in milled MoO3 powders

International Nuclear Information System (INIS)

Guerrero-Paz, J; Dorantes-Rosales, H; Aguilar-Martínez, J A; Garibay-Febles, V

2013-01-01

Powder of Molybdenum trioxide was milled for different times in horizontal ball mills. Such powder was characterized by TEM and XRD. Powder was rapidly de-agglomerated and fragmented up to attain nanoplates of two types, amorphous and crystalline. Finally, cold-welding of nanoplates occurred permitting some relaxation process to obtain a more stable energized structure consisting of equiaxial crystalline nanograins after 16 hours of milling.

Silicon heterojunction solar cell with passivated hole selective MoOx contact

Science.gov (United States)

Battaglia, Corsin; de Nicolás, Silvia Martín; De Wolf, Stefaan; Yin, Xingtian; Zheng, Maxwell; Ballif, Christophe; Javey, Ali

2014-03-01

We explore substoichiometric molybdenum trioxide (MoOx, x MoOx, we observe a substantial gain in photocurrent of 1.9 mA/cm2 in the ultraviolet and visible part of the solar spectrum, when compared to a p-type amorphous silicon emitter of a traditional silicon heterojunction cell. Our results emphasize the strong potential for oxides as carrier selective heterojunction partners to inorganic semiconductors.

First-principles study on influence of molybdenum on acicular ferrite formation on TiC particles in microallyed steels

Science.gov (United States)

Hua, Guomin; Li, Changsheng; Cheng, Xiaonong; Zhao, Xinluo; Feng, Quan; Li, Zhijie; Li, Dongyang; Szpunar, Jerzy A.

2018-01-01

In this study, influences of molybdenum on acicular ferrite formation on precipitated TiC particles are investigated from thermodynamic and kinetic respects. In thermodynamics, Segregation of Mo towards austenite/TiC interface releases the interfacial energy and induces phase transformation from austenite to acicular ferrite on the precipitated TiC particles. The Phase transformation can be achieved by displacive deformation along uniaxial Bain path. In addition, the segregation of Mo atom will also lead to the enhanced stability of ferrite in comparison with austenite no matter at low temperature or at high temperature. In kinetics, the Mo solute in acicular ferrite can effectively suppress the diffusion of carbon atoms, which ensures that orientation relationship between acicular ferrite and austenitized matrix can be satisfied during the diffusionless phase transformation. In contrast to ineffectiveness of TiC particles, the alloying Mo element can facilitate the formation of acicular ferrite on precipitated TiC particles, which is attributed to the above thermodynamic and kinetic reasons. Furthermore, Interfacial toughness and ductility of as-formed acicular ferrite/TiC interface can be improved simultaneously by segregation of Mo atom.

Paraelasticity in electron-irradiated molybdenum

International Nuclear Information System (INIS)

Beuneu, Brigitte; Quere, Yves.

1981-11-01

The relaxation of a radiation-induced point defect-most probably the rotation of a dumbell-is observed during isothermal anneals of irradiated molybdenum by resistivity measurements. The recovery of close pairs is not affected, in first analysis, by the presence of a uniaxial stress

Special features of nickel-molybdenum alloy electrodeposition onto screen-type cathodes

International Nuclear Information System (INIS)

Aleksandrova, G.S.; Varypaev, V.N.

1982-01-01

Electrolytic nickel-molybdenum alloy, which has a rather low hydrogen overpotential and high corrosion resistance, is of interest as cathode material in industrial electrolysis. Screen-type electrodes with a nickel-molybdenum coating can be used as nonconsumable cathodes in water-activated magnesium-alloy batteries

Determination of molybdenum in plant reference material by thermal-ionization isotope-dilution mass spectrometry

International Nuclear Information System (INIS)

Saumer, M.; Gantner, E.; Reinhardt, J.; Ache, H.J.

1992-01-01

An analytical method is described for the determination of the concentration and the isotopic composition of molybdenum in plant samples using thermal ionization mass spectrometry. After microwave acid digestion and liquid-liquid extractive separation with Amberlite LA-2, the molybdenum isotopes are measured as MoO 3 - -ions in a quadrupole mass spectrometer. In all cases, the relative standard deviation of the measurements of both natural and spike molybdenum was better than 3% for all ratios measured. The concentration of molybdenum found in three different plant reference materials agreed well with the certified values. (orig.)

Method for palladium activating molybdenum metallized features on a ceramic substrate

International Nuclear Information System (INIS)

Kumar, A.H.; Schwartz, B.

1985-01-01

A molybdenum or tungsten metallurgical pattern is formed on or in a dielectric green sheet. Palladium, nickel, platinum or rhodium is coated on a layer of polyvinyl butyral which is carried on a polyester film. The metal layer of this assembly is laminated to a dielectric green sheet which carries the molybdenum or tungsten metallurgy. The polyester film is stripped off. The resulting assembly is sintered to a fired structure, whereby the polyvinyl butyral is volatilized off and the palladium, nickel, platinum or rhodium is alloyed with the molybdenum or tungsten metallurgy to provide a densified metallurgy whose surface is free of glass

MOLYBDENUM CATALYZED ACID PEROXIDE BLEACHING OF EUCALYPTUS KRAFT PULP

Directory of Open Access Journals (Sweden)

Marcos S. Rabelo

2008-08-01

Full Text Available Molybdenum catalyzed peroxide bleaching (PMo Stage consists of pulp treatment with hydrogen peroxide under acidic conditions in the presence of a molybdenum catalyst. Molybdenum is applied in catalytic doses (50-200 mg/kg pulp and may originate from various sources, including (NH46Mo7O24.4H2O, Na2MoO4.2H2O, siliconmolybdate, etc. This work is aimed at optimizing the PMo stage and evaluating its industrial application in the OAZDP sequence. Optimum PMo stage conditions for bleaching eucalyptus pulp were 90 ºC, pH 3.5, 2 h, 0.1 kg/adt Mo and 5 kg/adt H2O2. The PMo stage was more efficient to remove pulp hexenuronic acids than lignin. Its efficiency decreased with increasing pH in the range of 1.5-5.5, while it increased with increasing temperature and peroxide and molybdenum doses. The application of the PMo stage as replacement for the A-stage of the AZDP sequence significantly decreased chlorine dioxide demand. The PMo stage caused a decrease of 20-30% in the generation of organically bound chlorine. The quality parameters of the pulp produced during the PMo stage mill trial were comparable to those obtained with the reference A-stage.

Brazing molybdenum and tungsten for high temperature service

International Nuclear Information System (INIS)

Lundberg, L.B.; Turner, W.C.; Hoffman, C.G.

1978-01-01

Investigations were conducted to develop vacuum brazes for molybdenum and tungsten which can be used in seal joint applications up to 1870 K (1597 C, 2907 F). Joints were attempted in molybdenum, tungsten and tungsten--molybdenum. The braze materials included: Ti--10Cr powder, Ti--30V wire, Ti--65V wire, V wire, Ni electroplate, MoB--50MoC powder mixture, V--50Mo powder mixture, Mo--15MoB 2 powder mixture and Mo--49V--15MoB 2 powder mixture. Braze temperature ranged from 1900 K (1627 C, 2961 F) to 2530 K, (2257 C, 4095 F), and leak-tight joints were made with all braze materials except Ti--10Cr. After heat treatments up to 1870 K (1597 C, 2907 F) Kirkendall voiding was found to cause leakage of some of the joints made with only substitutional alloying elements. However, adding base metal powders to the braze or narrowing the root opening eliminated this problem. Kirkendall voiding was not a problem when interstitial elements were a major ingredient in the braze material. Shear testing of Ti--65V, V, MoB--50MoC and V--50Mo brazed molybdenum at 1670 K (1397 C, 2547 F) indicated strengths equal to or better than the base metal. Ti--65V, V--50Mo and MoB--50MoC brazed joints were exposed to basalt at 1670 K (1397 C, 2547 F) for 3 h without developing leaks

GEMAS: Molybdenum Spatial Distribution Patterns in European Soil

Science.gov (United States)

Cicchella, Domenico; Zuzolo, Daniela; Demetriades, Alecos; De Vivo, Benedetto; Eklund, Mikael; Ladenberger, Anna; Negrel, Philippe; O'Connor, Patrick

2017-04-01

Molybdenum is an essential trace element for both plants and animals as well as for human being. It is one such trace element for which potential health concerns have been raised but for which few data exist and little investigation or interpretation of distributions in soils has been made. The main goal of this study was to fill this gap. Molybdenum (Mo) concentrations are reported for the similar spatial distribution patterns mainly governed by geology (parent material and mineralisation), as well as weathering, soil formation and climate since the last glaciations period. The dominant feature is represented by low Mo concentrations over the coarse-grained sandy deposits of the last glaciations in central northern Europe while the most extensive anomalies occur in Scandinavian soils. The highest Mo concentration value occurs to the North of Oslo close to one of the largest porphyry Mo deposit of the World. Some interesting anomalous patterns occur also in Italy in correspondence with alkaline volcanics, in Spain and Greece associated with sulfides mineralizations and in Slovenia and Croatia where are probably related to the long weathering history of karstic residual soils. Anomalous concentrations in some areas of Ireland represent a clear example of how an excess of molybdenum has produced potentially toxic pastures. In fact, these give rise to problems particularly in young cattle when excess molybdenum in the herbage acts as an antagonist, which militates against efficient copper absorption by the animal.

A review of chromium, molybdenum, and tungsten alloys

International Nuclear Information System (INIS)

Klopp, W.D.

1975-01-01

The mechanical properties of chromium, molybdenum, and tungsten alloys are reviewed, with particular emphasis on high-temperature strength and low-temperature ductility. Precipitate strengthening is highly effective at 0.4-0.8 Tsub(m) in these metals, with HfC being most effective in tungsten and molybdenum, and Ta(B,C) most effective in chromium. Low-temperature ductility can be improved by alloying to promote rhenium ductilizing or solution softening. The low-temperature mechanical properties of these alloys appear related to electronic interactions rather than to the usual metallurgical considerations. (Auth.)

Studying the electrochemical deposition process of molybdenum from aqueous solution of molybdate ions

Directory of Open Access Journals (Sweden)

Samira Fikret Cafarova

2016-02-01

Full Text Available In this study, the tracing of the electroreduction process of molybdate ions in aqueous media at different conditions is achieved for obtaining molybdenum metal in a simple and easy way. The kinetics and the mechanism of the electroreduction of molybdate ions are studied using cathodic polarization technique. It is observed that, the speed of the electroreduction process depends on the speed of the change of the cathodic potential sweep as well as on the temperature of the electrodeposition bath. Moreover, it is observed that, at the potential range from the stationary potential (Est = 0.25V to −0.7 V, the electroreduction of molybdate ions occurs into two steps. Moreover it is observed that, after −0.7 V the electroreduction process of molybdate is accompanying with evolution of hydrogen.

Mineral trioxide aggregate enhances the odonto/osteogenic capacity of stem cells from inflammatory dental pulps via NF-κB pathway.

Science.gov (United States)

Wang, Y; Yan, M; Fan, Z; Ma, L; Yu, Y; Yu, J

2014-10-01

This study was designed to investigate the effects of mineral trioxide aggregate (MTA) on the osteo/odontogenic differentiation of inflammatory dental pulp stem cells (iDPSCs). inflammatory DPSCs were isolated from the inflammatory pulps of rat incisors and cocultured with MTA-conditioned medium. MTT assay and flow cytometry were performed to evaluate the proliferation of iDPSCs. Alkaline phosphatase (ALP) activity, alizarin red staining, real-time RT-PCR, and Western blot assay were used to investigate the differentiation capacity as well as the involvement of NF-κB pathway in iDPSCs. Mineral trioxide aggregate-treated iDPSCs demonstrated the higher ALP activity and formed more mineralized nodules than the untreated group. The odonto/osteoblastic markers (Alp, Runx2/RUNX2, Osx/OSX, Ocn/OCN, and Dspp/DSP, respectively) in MTA-treated iDPSCs were significantly upregulated as compared with untreated iDPSCs. Mechanistically, cytoplastic phos-P65 and nuclear P65 in MTA-treated iDPSCs were significantly increased in a time-dependent manner. Moreover, the inhibition of NF-κB pathway suppressed the MTA-induced odonto/osteoblastic differentiation of iDPSCs, as indicated by decreased ALP levels, weakened mineralization capacity and downregulated levels of odonto/osteoblastic genes (Osx, Ocn, and Dspp). Mineral trioxide aggregate enhances the odonto/osteogenic capacity of DPSCs from inflammatory sites via activating the NF-κB pathway. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Structural integrity testing of glass-ceramic/molybdenum vacuum tube frames

International Nuclear Information System (INIS)

Spears, R.K.

1980-01-01

In this study, vacuum tube subassemblies made of glass-ceramic insulators sealed to inner and outer molybdenum frames were loaded in compression to failure with a tensile test machine. Several factors were varied in processing these subassemblies. These factors included etching and nonetching of molybdenum piece parts, annealing and nonannealing of subassemblies, and vapor and non-vapor honing of insulators after sealing. After failure, the subassemblies were examined for fracture patterns. In most cases, fracture started at points near the lower portion of the inner sleeve-insulator interface. More load was carried by subassemblies having molybdenum piece parts that were acid etched. No difference appeared between the strength of subassemblies having annealed and nonannealed glass-ceramic insulators. Parts with vapor-honed insulators failed at substantially lower loads

High-temperature performance of the brazement of molybdenum single crystals

International Nuclear Information System (INIS)

Hirakoa, Y.

1992-01-01

Molybdenum is utilized in the fields of high-temperature vacuum industry, electrical and electronic industry, and chemical industries. For the wider application of this material, however, it is necessary to obtain a joining with good quality. In this investigation, high-temperature brazing of a single-crystalline molybdenum was performed. Then the bend properties of the brazement after a high-temperature annealing were evaluated. The single-crystalline molybdenum had been produced by the secondary recrystallization method. Brazing was performed in vacuum at 2273K using Mo-40Ru alloy powder as a brazing material. The brazement was investigated via optical microscopy, EPMA, Knoop hardness, and three point bending. In this paper the effects of annealing in hydrogen and vacuum are discussed

Study of the early stages of precipitation of molybdenum in steelwelds

International Nuclear Information System (INIS)

Choudhary, H.U.

2001-01-01

The addition of molybdenum to steel welds in quite small concentrations leads to a variety of anomalous microstructural and mechanical property effects. In some cases, the effects manifest even there are no obvious changes in microstructure at the resolution of a transmission electron microscope. It has been reported in the published literature, that an increase in the molybdenum concentration leads to a corresponding increase in the proportion of primary microstructure in multipass welds. Another striking anomaly with molybdenum containing welds, identified in the published literature, is that the strength of such welds is much higher than is estimated using normally reliable models for he prediction of mechanical properties. The surprising feature of this anomaly is that it is present even for the as-deposited microstructure, which has not been deliberately or otherwise tempered. The anomaly cannot therefore be attributed to easily observed secondary hardening effects, and indeed precipitates such a molybdenum carbides are not found to occur in the as-deposited state at the resolution of a conventional transmission electron microscope. An investigation has been carried out to study the possible existence of the early stages of precipitation/clustering of molybdenum atoms, using the atomic resolution method know as APFIM (Atom Probe Field Ion Microscopy). The results has given a strong indication that the anomalous strengthening in the as deposited welds is due to sub-microscopic effects, arising from the fine scale clustering of molybdenum atoms. This clustering appears to occur in the ferrite as the weld cools to ambient temperature after solidification. The effect is essentially secondary hardening, but at the very early stages. (author)

Correlation of microstructure and wear resistance of molybdenum blend coatings fabricated by atmospheric plasma spraying

International Nuclear Information System (INIS)

Hwang, Byoungchul; Lee, Sunghak; Ahn, Jeehoon

2004-01-01

The correlation of microstructure and wear resistance of various molybdenum blend coatings applicable to automotive parts was investigated in this study. Five types of spray powders, one of which was pure molybdenum powder and the others were blends of brass, bronze, and aluminum alloy powders with molybdenum powder, were deposited on a low-carbon steel substrate by atmospheric plasma spraying (APS). Microstructural analysis of the coatings showed that they consisted of a curved lamellar structure formed by elongated splats, with hard phases that formed during spraying being homogeneously distributed in the molybdenum matrix. The wear test results revealed that the blend coatings showed better wear resistance than the pure molybdenum coating because they contained a number of hard phases. In particular, the molybdenum coating blended with bronze and aluminum alloy powders and the counterpart material showed an excellent wear resistance due to the presence of hard phases, such as CuAl 2 and Cu 9 Al 4 . In order to improve overall wear properties for the coating and the counterpart material, appropriate spray powders should be blended with molybdenum powders to form hard phases in the coatings

A novel route to nanosized molybdenum boride and carbide and/or metallic molybdenum by thermo-synthesis method from MoO3, KBH4, and CCl4

International Nuclear Information System (INIS)

Li Yuanzhi; Fan Yining; Chen Yi

2003-01-01

Nanosized molybdenum boride and carbide were synthesized from MoO 3 , KBH 4 , and CCl 4 by thermo-synthesis method at lower temperature. The relative content of Mo, Mo 2 C, and molybdenum boride in the product was decided by the molar ratio between MoO 3 , KBH 4 , and CCl 4 . Increasing the molar ratio of CCl 4 to MoO 3 was favorable to the production of Mo 2 C. Increasing the molar ratio of KBH 4 to MoO 3 was favorable to the production of molybdenum boride. By carefully adjusting the reaction conditions and annealing in Ar at 900 deg. C, a single phase of MoB could be obtained

Preparation and properties of molybdenum-tungsten-carbonitrides

International Nuclear Information System (INIS)

Schreiner, M.; Ettmayer, P.; Kieffer, R.

1982-01-01

Molybdenum-tungsten-carbonitrides can be prepared by reacting prealloyed powders of Mo and W with carbon in the presence of nitrogen or ammonia. Single phase carbonitrides (Mo,W) (C,N) with the WC-type structure can be obtained. The nitrogen content of these carbonitrides increases with increasing molybdenum content. Flowing ammonia has a decarburizing effect, which has to be counterbalanced by an addition of a carbonaceous gas such as methane. Nitrogen instead of ammonia is equally effective and gives carbonitrides which have a nitrogen content only insignificantly lower than the carbonitrides obtained in flowing ammonia. The lattice parameters of the carbonitrides are found to slightly smaller than the lattice parameters of the corresponding carbides. (Author)

Recovery of molybdenum in froth flotation

International Nuclear Information System (INIS)

Parlman, R.M.; Bresson, C.R.

1981-01-01

Beta-mercaptoethanol has been found to be an effective suppressant for such minerals as copper, iron and lead in a molybdenum sulfide ore froth flotation operation. The recovery process and a suppressant utilizing said compound are claimed

Use of molybdenum as a structural material of fuel elements for improving nuclear reactors safety

Energy Technology Data Exchange (ETDEWEB)

Shmelev, Anatoly N.; Kulikov, Gennady G.; Kozhahmet, Bauyrzhan K.; Kulikov, Evgeny G.; Apse, Vladimir A. [National Research Nuclear Univ., Moscow (Russian Federation). Moscow Engineering Physics Institute (MEPhI)

2016-12-15

Main purpose of the study is justifying the use of molybdenum as a structural material of fuel elements for improving the safety of nuclear reactors. Particularity of the used molybdenum is that its isotopic composition corresponds to molybdenum, which is obtained as tailing during operation of the separation cascade for producing a material for medical diagnostics of cancer. The following results were obtained: A method for reducing the thermal constant of fuel elements for light water and fast reactors by using dispersion fuel in cylindrical fuel rods containing, for example, granules of metallic U-Mo-alloy into Mo-matrix was proposed; the necessity of molybdenum enrichment by weakly absorbing isotopes was shown; total use of isotopic molybdenum will be more than 50 %.

HYDROGEN VACANCY INTERACTION IN MOLYBDENUM

NARCIS (Netherlands)

Abd El Keriem, M.S.; van der Werf, D.P.; Pleiter, F

1993-01-01

Vacancy-hydrogen interaction in molybdenum was investigated by means of the perturbed angular correlation technique, using the isotope In-111 as a probe. The complex InV2 turned out to trap up to two hydrogen atoms: trapping of a single hydrogen atom gives rise to a decrease of the quadrupole

Evaluation of SinoRhizobium meliloti Efficiency and Qualitative Traits of Alfalfa under Application of Molybdenum

Directory of Open Access Journals (Sweden)

F Ahmadi Dana

2017-12-01

Full Text Available Introduction Agriculture depends heavily on nitrogen which is biologically fixed through the symbiotic association between rhizobia and legume plants in nodules located on plant roots. Alfalfa is a legume that should fix most of its own N requirement if it is sufficiently nodulated by viable Rhizobium meliloti inoculums. The process of nitrogen fixation is done by the help of an enzyme called nitrogenase and molybdenum which is an important element in the formation of this compound. Molybdenum is required by plants for protein synthesis and is especially important for legumes as it is needed for nitrogen fixation by rhizobia. Therefore the following research was done aimed on studying the effect of different amount of molybdenum and S. rhizobium bacteria on alfalfa’s yield. Material and Methods Alfalfa (Medicago sativa were grown in a field. The experiment was conducted at Karaj in 2013 in split plot arrangement based on completely randomized block design (RCBD, including 2 caring S. rhizobium inoculated seed and non-inoculated as the main plot factorand 3 levels of Molybdenum (0,5,10 kg ha-1 from ammonium molybdate (as the sub plot factor in three replications. Sinorhizobium meliloti bacteria were cultured on plates. Then half of the seeds were inoculated by Sinorhizobium meliloti. Nitrogen fertilizer was added only in one stage before planting up to 50 kg per hectare. Plants were grown until flowering. The data were analyzed by the SAS (9.1 software and mean comparisons were done by Duncan's MRT at the 1% and 5% probability level. Results and Discussion The results showed the effect of different levels of molybdenum and S. Rhizobium bacteria on dry matter yield, molybdenum concentrations in shoots and roots and the number of root nodules was significant. This treatment was significant in comparison to the control treatment with the14.27 ton per hectare. Increasing of molybdenum application, led to increasing of root nodules and showed a

Effect of high concentration of molybdenum on the structure and properties of niobium

International Nuclear Information System (INIS)

Trekina, M.I.; Vasil'eva, E.V.

1989-01-01

The effect of alloying of 20,25 and 30 % Mo on the structure and mechanical properties of niobium is studied. It is shown that niobium alloying with molybdenum in the studied concentration leads to grain grinding, which increases with the molybdenum content growth in the alloy. The effective energy values of recrystallization activation of the studied niobium and molybdenum alloys are determined. The high hardness level at some plasticity and deformability of niobium alloy with 20 % Mo is established

Composite sheet made of molybdenum and dispersion-strengthened copper

International Nuclear Information System (INIS)

Nicholson, R.D.; Fusco, R.S.

1990-01-01

This patent describes a roll-bonded composite sheet product having at least one layer of dispersion-strengthened copper and at least one layer of molybdenum. The composite is characterized by a sharply defined, cleavage-resistant interface between the copper and the molybdenum with substantially no detectable diffusion of one metal into the other across the interface. The composite is resistant to delamination and being capable of maintaining structural integrity upon repeated high temperature firings at temperatures up to 900 degrees C

Cleavage and formation of molecular dinitrogen in a single system assisted by molybdenum complexes bearing ferrocenyldiphosphine.

Science.gov (United States)

Miyazaki, Takamasa; Tanaka, Hiromasa; Tanabe, Yoshiaki; Yuki, Masahiro; Nakajima, Kazunari; Yoshizawa, Kazunari; Nishibayashi, Yoshiaki

2014-10-20

The N≡N bond of molecular dinitrogen bridging two molybdenum atoms in the pentamethylcyclopentadienyl molybdenum complexes that bear ferrocenyldiphosphine as an auxiliary ligand is homolytically cleaved under visible light irradiation at room temperature to afford two molar molybdenum nitride complexes. Conversely, the bridging molecular dinitrogen is reformed by the oxidation of the molybdenum nitride complex at room temperature. This result provides a successful example of the cleavage and formation of molecular dinitrogen induced by a pair of two different external stimuli using a single system assisted by molybdenum complexes bearing ferrocenyldiphosphine under ambient conditions. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

An experimental study of steam explosions involving CORIUM melts

International Nuclear Information System (INIS)

Millington, R.A.

1984-05-01

An experimental programme to investigate molten fuel coolant interactions involving 0.5 kg thermite-generated CORIUM melts and water has been carried out. System pressures and initial coolant subcoolings were chosen to enhance the probability of steam explosions. Yields and efficiencies of the interactions were found to be very close to those obtained from similar experiments using molten UO 2 generated from a Uranium/Molybdenum Trioxide thermite. (author)

Low resistivity molybdenum thin film towards the back contact of dye ...

Indian Academy of Sciences (India)

Abstract. This paper reports the optimization of the molybdenum thin film electrode as the back contact of dye-sensitized solar cell (DSSC). The molybdenum thin film was grown on the glass substrate by direct current sputtering techniques of which the sputtering power was 150Wat 18 sccm flow rate of Ar. At such sputtering ...

Separation of fission Molybdenum for production of technetium generator

International Nuclear Information System (INIS)

Bayat, L.; Shaham, V.; Davarkha, R.

2002-01-01

There are two basically different methods for Mo-99 productions: Activation of Mo-99 contained at about 24% in natural isotopic mixtures. Mo-98 enriched targets are irradiated in high-flux reactors in order to achieve the highest possible specific activity of the product. Idolisation of fission molybdenum from irradiated nuclear fuel targets which have undergone short-term cooling. Maximum fission yield can be attained by irradiation of uranium-235 with the highest possible enrichment. On account of its approximately 1000 times higher specific activity. Fission molybdenum has almost replaced worldwide the product fabricated by activation. However, fission molybdenum-99 production has as its prerequisite a suitably advanced technology by which the production process taking place under high activity conditions can be controlled. An integral part of the process consist in the retention of the fission gases the recycling of non-consumed fuel and the treatment of the waste streams arising. This publication will deal with the individual steps in the process

Management of immature teeth with apical infections using mineral trioxide aggregate

Directory of Open Access Journals (Sweden)

Sivakumar Nuvvula

2010-01-01

Full Text Available Traumatic injuries to the young permanent teeth lead to devitalization of the pulp with concomitant arrest in further development of the immature root of the involved tooth. Hermetic seal of the root canal system during obturation is not possible in such cases, due to the lack of an apical constriction. The traditional management technique in such cases has been apexification involving induction of a calcific barrier at the apex using calcium hydroxide, which in turn facilitates obturation of the root canal. However this becomes complicated when there is persistent infection leading to periapical changes. This case report describes the use of mineral trioxide aggregate (MTA for management of a periapically compromised immature tooth.

Atomic physics for fusion plasma spectroscopy; a soft x-ray study of molybdenum ions

International Nuclear Information System (INIS)

Fournier, K.B.

1996-01-01

Understanding the radiative patterns of the ions of heavy atoms (Z approx-gt 18) is crucial to fusion experiments. The present thesis applies ab initio, relativistic calculations of atomic data to modeling the emission of molybdenum (Z = 42) ions in magnetically confined fusion plasmas. The models are compared to observations made in the Alcator C-Mod tokamak (Plasma Fusion Center, Massachusetts Institute of Technology), and the Frascati Tokamak Upgrade. Experimental confirmation of these models allows confidence in calculations of the total molybdenum concentration and quantitative estimates of the total power lost from the plasmas due to molybdenum line radiation. Charge states in the plasma core (Mo 33+ to Mo 29+ ) emit strong x-ray and XUV spectra which allow benchmarking of models for the spatial distribution of highly stripped molybdenum ions; the models only achieve agreement with observations when the rates of indirect ionization and recombination processes are included in the calculation of the charge state distribution of the central molybdenum ions. The total concentration of molybdenum in the core of the plasma is found, and the total power radiated from the plasma core is computed. Observations of line emission from more highly charged molybdenum ions (Mo 36+ to Mo 34+ ) are presented. open-quotes Bulkclose quotes molybdenum charge states (Mo 25+ to Mo 23+ ) emit complicated XUV spectra from a position in the plasma near C-Mod's half radius; spatial profiles of these ions' emission are analyzed. Models for the line-emission spectra of adjacent ions (Mo 28+ to Mo 26+ ) are offered, and the accuracy and limits of ab initio energy level calculations are discussed. open-quotes Edgeclose quotes charge states (Mo 22+ to Mo 15 ) extend to the last closed magnetic flux surface of the C-Mod plasma. The strongest features from these charge states are emitted in a narrow band from ∼70 Angstrom

Development of an environmentally friendly protective coating for the depleted uranium-0.75 wt% titanium alloy

International Nuclear Information System (INIS)

Roeper, Donald F.; Chidambaram, Devicharan; Clayton, Clive R.; Halada, Gary P.; Derek Demaree, J.

2006-01-01

Molybdenum oxide-based conversion coatings have been formed on the surface of the depleted uranium-0.75 wt% titanium alloy using either concentrated nitric acid or fluorides for surface activation prior to coating formation. The acid-activated surface forms a coating that offers corrosion protection after a period of aging, when uranium species have migrated to the surface. X-ray photoelectron spectroscopy (XPS) revealed that the protective coating is primarily a polymolybdate bound to a uranyl ion. Rutherford backscattering spectroscopy (RBS) on the acid-activated coatings also shows uranium dioxide migrating to the surface. The fluoride-activated surface does not form a protective coating and there are no uranium species on the surface as indicated by XPS. The coating on the fluoride-activated samples has been found to contain a mixture of molybdenum oxides of which the main component is molybdenum trioxide and a minor component of an Mo(V) oxide

Flame retardant synergism between molybdenum and halogen-containing compounds in unsaturated polyesters. [Smoke suppression

Energy Technology Data Exchange (ETDEWEB)

Skinner, G.A.; Parker, L.E.; Marshall, P.J.

1978-01-01

Oxygen index results for a series of unsaturated polyesters, containing molybdenum oxide and various halogenated compounds, have provided definite evidence for some form of flame retardant synergistic effect between molybdenum and halogen. With the halogenated compounds used, the magnitude of the effect was greater in the presence of bromine but was dependent on the type of compound. When dibromoneopentyl glycol was used as the bromine source, the synergistic effect exhibited by molybdenum oxide was comparable to that shown by antimony oxide. Since molybdenum oxide also acts as a smoke suppressant, it could offer a useful alternative to antimony oxide particularly in the light of probable changes in standards and regulatory control regarding smoke emission. 4 figures, 2 tables.

Experimental study on effect of arsenic trioxide on vascular smooth muscle cells

International Nuclear Information System (INIS)

Lu Qin; An Yanli; Niu Huanzhang; Teng Gaojun; Wang Zihao; Zhang Dongsheng; Fang Juanjuan

2007-01-01

Objective: To investigate the effect of arsenic trioxide (As 2 O 3 ) nanoparticles on rabbit vascular smooth muscle cells in vitro in comparison with normal form As 2 O 3 . Methods: The rabbit vascular smooth muscle cells were cultured in vitro. Nano and normal forms of As 2 O 3 with drug concentrations of 3 μmol/L were added into the cells. Cell proliferation curve was drawn according to the light absorption values of MTT test. Flow cytometry was applied to observe the apoptosis. DNA was extracted and underwent electrophoresis. Results: Cell proliferation treated with the 3 μmol/L concentration of As 2 O 3 was inhibited. Cell growth was inhibited markedly with increased treatment time, and the inhibition effect of nano drug form seemed stronger than that of normal form. MTT light absorption values of cells treated at 24, 48 and 72 h showed statistically significant difference (H=10.934, 15.039, 15.539, P 2 O 3 , normal drug form of As 2 O 3 and control group of cells without As 2 O 3 were 44.97%, 58.54%, 74.02% respectively. The early apoptosis rates were 16.89%, 11.27%, 11.20%, late apoptosis rates were 26.56%, 23.60%, 12.46%, and necrosis rates were 11.58%, 6.59%, 2.32% respectively. Agarose gel electrophoresis showed 'ladder' strand of DNA, with more strands and obscurity for nano drug form treated cells. Conclusion: Arsenic trioxide may inhibit the growth of rabbit vascular smooth muscle cells. The nano drug form showed stronger inhibition effect than that of the normal drug form. (authors)

Determination of molybdenum (VI) in sea water with preliminary concentration by the method of ion flotation

International Nuclear Information System (INIS)

Andreeva, I. Yu.; Drapchinskaya, O.L.; Lebedeva, L.I.

1985-01-01

The purpose of this paper is to assess the feasibility of using the method of ion flotation for the concentration of microamounts of molybdenum (VI) during determination in sea water. The ion flotation method is used for the purification of industrial sewage from the ions of nonferrous metals, including molybdenum (VI) with its content of up to 50 mg/liter. A 1.10 -4 M solution of sodium molybdate in 0.1M NaOH was used. The effect of different factors on the ion flotation process of molybdenum (VI) was investigated: pH of the solution, flotation times, concentrations of surface-active substances (SAS), molybdenum (IV), extraneous salts. Data presented show that the ion flotation method in conjunction with the photometric method of determining molybdenum with brompyrogallol red (BPR) and cetylpridinium chloride (CP) (limit of detection 0.02 micrograms/liter) allows the content of molybdenum (VI) in sea water to be established with sufficient reliability and reproducibility

Derivation of kinetic coefficients by atomistic methods for studying defect behavior in Mo

International Nuclear Information System (INIS)

Insepov, Z.; Rest, J.; Yacout, A.M.; Kuksin, A.Yu.; Norman, G.E.; Stegailov, V.V.; Starikov, S.V.; Yanilkin, A.V.

2012-01-01

Highlights: ► A multiscale concept couples molecular dynamics (MD) with ab initio and kinetic rate theory. ► Evolution of a system of self-interstitial atoms and vacancies in Mo is studied by MD. ► Formation of di-SIA clusters and SIA–vacancy recombination is analyzed. ► 1D diffusion of self-interstitials at various temperature and defect concentrations were studied. ► This paper provides a powerful predictive tool for simulating irradiation of nuclear materials. - Abstract: A multiscale concept for irradiated materials simulation is formulated based on coupling molecular dynamics simulations (MD) where the potential was obtained from ab initio data of energies of the basic defect structures, with kinetic mesoscale models. The evolution of a system containing self-interstitial atoms (SIAs) and vacancies in crystalline molybdenum is investigated by means of MD. The kinetics of formation of di-SIA clusters and SIA–vacancy recombination is analyzed via approaches used in the kinetic theory of radiation ageing. The effects of 1D diffusion of SIAs, temperature, and defect concentrations on the reaction rates are also studied. This approach can validate both the kinetic mechanisms and the appropriate kinetic coefficients, offering the potential to significantly reduce the uncertainty of the kinetic methodology and providing a powerful predictive tool for simulating irradiation behavior of nuclear materials.

Strengthening and elongation mechanism of Lanthanum-doped Titanium-Zirconium-Molybdenum alloy

Energy Technology Data Exchange (ETDEWEB)

Hu, Ping, E-mail: huping1985@126.com [School of Metallurgy Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Jinduicheng Molybdenum Co., Ltd., Xi’an 710068 (China); Hu, Bo-liang; Wang, Kuai-she; Song, Rui; Yang, Fan [School of Metallurgy Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Yu, Zhi-tao [Ruifulai Tungsten & Molybdenum Co., Ltd., Xi’an 721914 (China); Tan, Jiang-fei [School of Metallurgy Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Cao, Wei-cheng; Liu, Dong-xin; An, Geng [Jinduicheng Molybdenum Co., Ltd., Xi’an 710068 (China); Guo, Lei [Ruifulai Tungsten & Molybdenum Co., Ltd., Xi’an 721914 (China); Yu, Hai-liang [School of Mechanical, Materials and Mechatronics Engineering, University of Wollongong, NSW 2522 (Australia)

2016-12-15

The microstructural contributes to understand the strengthening and elongation mechanism in Lanthanum-doped Titanium-Zirconium-Molybdenum alloy. Lanthanum oxide particles not only act as heterogeneous nucleation core, but also act as the second phase to hinder the grain growth during sintering crystallization. The molybdenum substrate formed sub-grain under the effect of second phase when the alloy rolled to plate.

Electrochemistry and biochemistry of molybdenum. Ehlektrokhimiya i biokhimiya molibdena

Energy Technology Data Exchange (ETDEWEB)

Ryzhov, A M; Zajtsev, P M; Mambetkaziev, E A; Zhdanov, S I

1992-07-01

Using the review of data on polarographic behaviour of double and ternary systems molybdenum(6)-oxidant-organic ligand (oxy- and aminoacids of protein composition) by way of example, the possibility to use the metal ferments for the study of peculiarities in behaviour of the metal ions manifested in reactions was considered. The content of molybdenum in organism is noticeably different for healthy people and patients with malignant neoplasms and diabetes mellitus. There is a certain relation between catalytic activity of the metal ions and multiplicity of their accumulation in human organism.

A redox-assisted molecular assembly of molybdenum oxide amine composite nanobelts

International Nuclear Information System (INIS)

Luo Haiyan; Wei Mingdeng; Wei Kemei

2011-01-01

Research highlights: → Nanobelts of molybdenum oxide amine were first synthesized via a redox-assisted molecular assembly route. → These nanobelts are highly crystalline with a several tens of micrometers in length and 20-30 nm in thickness. - Abstract: In this paper, the nanobelts of molybdenum oxide amine composite were successfully synthesized via a redox-assisted molecular assembly route under the hydrothermal conditions. The synthesized nanobelts were characterized by XRD, SEM, TEM, TG and FT-IR measurements. The thickness of nanobelts is found to be ca. 20-30 nm and their lengths are up to several tens of micrometers. Based on a series of the experimental results, a possible model, redox-intercalation-exfoliation, was suggested for the formation of nanobelts of molybdenum oxide amine composite.

Effect of pH and modifier-concentration on the solvent extraction of molybdenum with an alkyl amine

International Nuclear Information System (INIS)

Al-Siddique, F.R.; Adeler, I.; Huwyler, S.

1980-07-01

The results of the extraction behaviour of molybdenum in aqueous sulfuric acid solutions of an alkyl amine (amberlite LA-2) in kerosene under various pH and in the presence of various percentage of 1-octanol has been reported. The concentration of molybdenum employed was high enough to precipitate it partially during extraction as an amine-molybdenum complex. The maximum extraction coefficient was found to lie between pH 1.5-2.5. Presence of 1-octanol increased the extraction coefficient of molybdenum by increasing the solubility of the amine-molybdenum complex in the organic phase without changing the pH at the maximum extraction. (Auth.)

Effect of molybdenum status on the ascorbic acid content of plants in sand culture

Energy Technology Data Exchange (ETDEWEB)

Hewitt, E J; Agarwala, S C; Jones, E W

1950-12-30

The role of molybdenum in higher plants is generally thought to be closely connected with the assimilation of nitrate nitrogen. The nature of the system involved in nitrate assimilation and the step activated by molybdenum are still obscure. Preliminary results are presented which indicate that molydenum deficiency consistently causes a striking and generally significant reduction in the apparent ascorbic acid content of several crops. Molydenum-deficient plants were also injected through the petioles with molybdenum; there was a detectable rise in ascorbic acid content in 24 hr. The first visual response to molybdenum was just perceptible in three days as chlorophyll formation, and growth response could be detected about seven days after injection. Several hypotheses to account for the results obtained are discussed. 13 references, 1 table.

Growth and surface characterization of sputter-deposited molybdenum oxide thin films

Energy Technology Data Exchange (ETDEWEB)

Ramana, Chintalapalle V.; Atuchin, Victor V.; Kesler, V. G.; Kochubey, V. A.; Pokrovsky, L. D.; Shutthanandan, V.; Becker, U.; Ewing, Rodney C.

2007-04-15

Molybdenum oxide thin films were produced by magnetron sputtering using a molybdenum (Mo) target. The sputtering was performed in a reactive atmosphere of argon-oxygen gas mixture under varying conditions of substrate temperature (Ts) and oxygen partial pressure (pO2). The effect of Ts and pO2 on the growth and microstructure of molybdenum oxide films was examined in detail using reflection high-energy electron diffraction (RHEED), Rutherford backscattering spectrometry (RBS), energy dispersive X-ray spectrometry (EDS), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) measurements. The analyses indicate that the effect of Ts and pO2 on the microstructure and phase of the grown molybdenum oxide thin films is remarkable. RHEED and RBS results indicate that the films grown at 445 *C under 62.3% O2 pressure were stoichiometric and polycrystalline MoO3. Films grown at lower pO2 were nonstoichiometric MoOx films with the presence of secondary phase. The microstructure of the grown Mo oxide films is discussed and conditions were optimized to produce phase pure, stoichiometric, and highly textured polycrystalline MoO3 films.

Study of defects near molybdenum surface using thermal desorption spectrometer

International Nuclear Information System (INIS)

Naik, P.K.

1980-01-01

Thermal desorption spectrometry is utilized to study the migration of atoms and defects near molybdenum surface. The thermal desorption spectra of inert gas ions (neon, argon and krypton) injected with various energies (430-1950 eV) into a polycrystalline molybdenum target with various dosages (6.4 x 10sup(12) - 3.9 x 10sup(14) ions/cmsup(2)) are investigated. Four different states of binding of the trapped atoms corresponding to the activation energies for desorption have been revealed from the spectra. The activation energies are found to be relatively insensitive to the species of the bombarding ion, incident ion energy and the dosage. The patterns of the spectra are strongly influenced by the mean projected range of the ions into the solid. The activation energies deduced are in good agreement with those reported for the migration of atoms and defects in molybdenum. (auth.)

Determination of molybdenum in various materials by normal-phase liquid chromatography using N-benzoyl-N-phenylhydroxylamine

International Nuclear Information System (INIS)

Bagur, Gracia; Sanchez-Vinas, Mercedes; Gazquez, Domingo

1995-01-01

A normal-phase liquid chromatographic method for the selective determination of molybdenum with N-benzoyl-N-phenylhydroxylamine is described. The molybdenum(VI) complex was preconcentrated by extraction into chloroform and injected onto a nitrile column for chromatography. The mobile phase was a 0.075 M solution of reagent in chloroform (stabilized with amylene). The detection limit for molybdenum by the proposed method was 0.88 ng for a phase volume ratio of 20:1 (aqueous to organic). Molybdenum has been determined in several samples with satisfactory accuracy and precision

Study of the molybdenum retention in alumina

International Nuclear Information System (INIS)

Wilkinson, Maria V.; Mondino, Angel V.; Manzini, Alberto

2002-01-01

The Argentine National Atomic Energy Commission routinely produces 99 Mo by fission of highly enriched uranium contained in targets irradiated in RA-3 reactor. The current process begins with the dissolution of the irradiated target in a basic media, considering the possibility of changing the targets, it could be convenient to dissolve them in acid media. The use of alumina as a first separation step in acid dissolution processes is already known although it is necessary to determine both the type of alumina to be used and the separation conditions. The study of molybdenum retention in alumina was performed at laboratory scale, using Mo-99 as radiotracer. Different kinds of alumina were tried, varying charge solution acidity. Influence of uranium concentration in the loading solution on molybdenum retention was also studied. (author)

Investigation of molybdenum pentachloride interaction with chlorine

International Nuclear Information System (INIS)

Salyulev, A.B.; Vovkotrub, Eh.G.; Strekalovskij, V.N.

1993-01-01

In Raman spectra of molybdenum pentachloride solutions in liquid chlorine lines were recorded in case of 397, 312, 410, 217 and 180 cm - 1 vibrations of ν 1 (A 1 '), ν 2 (A 1 '), ν 5 (E'), ν 6 (E') and ν 8 (E'') monomer (symmetry D 3h ) molecules of MoCl 5 . Interaction of molten molybdenum pentachloride with chlorine at increased (up to 6 MPa) pressures of Cl 2 was studied. In Raman spectra of its vapour distillation in liquid chlorine alongside with MoCl 5 lines appearance of new lines at 363 and 272 cm -1 , similar in their frequency to the ones calculated for the vibrations ν 1 (A 1g ) and ν 2 (E g ) of MoCl 6 molecules (symmetry O h ), was observed

Bandgap tunability at single-layer molybdenum disulphide grain boundaries

KAUST Repository

Huang, Yu Li

2015-02-17

Two-dimensional transition metal dichalcogenides have emerged as a new class of semiconductor materials with novel electronic and optical properties of interest to future nanoelectronics technology. Single-layer molybdenum disulphide, which represents a prototype two-dimensional transition metal dichalcogenide, has an electronic bandgap that increases with decreasing layer thickness. Using high-resolution scanning tunnelling microscopy and spectroscopy, we measure the apparent quasiparticle energy gap to be 2.40±0.05 eV for single-layer, 2.10±0.05 eV for bilayer and 1.75±0.05 eV for trilayer molybdenum disulphide, which were directly grown on a graphite substrate by chemical vapour deposition method. More interestingly, we report an unexpected bandgap tunability (as large as 0.85±0.05 eV) with distance from the grain boundary in single-layer molybdenum disulphide, which also depends on the grain misorientation angle. This work opens up new possibilities for flexible electronic and optoelectronic devices with tunable bandgaps that utilize both the control of two-dimensional layer thickness and the grain boundary engineering.

Direct determination of molybdenum in seawater by adsorption voltametry

International Nuclear Information System (INIS)

Berg, M.G. van den.

1985-01-01

Complex ions of molybdenum(VI) with 8-hydroxyquinoline (oxine) are shown to adsorb onto the hanging mercury drop electrode. This property forms the basis of a sensitive electrochemical technique by which dissolved molybdenum in seawater can be determined directly. The reduction current of adsorbed complex ions is measured by differential pulse adsorption voltametry, preceded by a period of 1 or 2 min of unstirred collection at an adsorption potential of -0.2 V. In the presence of 2 x 10 -3 M oxine and at pH 2.5 the potential of the main reduction peak is located at -0.59 V. The peak current-molybdenum concentration relationship is linear up to 3 x 10 -7 M; the detection limit is 4 nM. Greater sensitivity is obtained after stirred collection at pH 3.0 and with 10 -4 M oxine, but the calibration curve is nonlinear. In these conditions the limit of detection lies at 10 -10 M after 10 min stirred collection. 19 references, 8 figures

Effect of deformation diagram on molybdenum structure and properties

International Nuclear Information System (INIS)

Larin, Eh.N.; Abalikhin, A.A.; Kolikov, A.P.; Ushakova, N.E.

1984-01-01

Effect of deformation diagram on a tendency to lamination and mechanical properties of disks made of molybdenum alloy is studied. Investigated samples were subjected to hot rolling or forging. X-ray structural analysis of texture is carried out along with estimation of the level of mechanical properties across item cross section. Sample mechanical bending tests were conducted. Sample microstructure is also studied. It is shown that rolled molybdenum has a tendency to lamination, but forged molybdenum is free of such a tendency. Forged sample ductility is practically equal in all directionse but rolled sample ductility in a surface layer is high and decreases with depth. A conclusion is drawn that forged sample grains in a setting surface are equiaxial, but distinct deformation texture is observed for rolled samples and their grains are elongated in the direction of rolling. A conclusion is made that a flow diagram of the process of disk fabrication by forging or stamping ppovides a necessary complex of physicomechanical properties of metal as compared to polling, and metal discharge coefficient decreases sharply in this case

Assessing the efficiency of aluminium phosphide and arsenic trioxide in controlling the Indian crested porcupine (hystrix indica) in an irrigated forest plantation or Punjab, Pakistan

International Nuclear Information System (INIS)

Khan, A.A.

2010-01-01

The Indian crested porcupine, Hystrix indica, is widely distributed in the irrigated forests of Punjab, Pakistan and causes serious damage to trees, nursery stocking, field crops and vegetables. Field trials were conducted to determine the efficacy of aluminium phosphide (Phostoxin, 3g tablets) and arsenic trioxide bait (at 2.5g per apple) against the porcupine in a forest plantation. For fumigation with phostoxin, tablets were used at the rate of four, five, six and seven tablets per den. Observations showed that four tablets were ineffective, five and six tablets provided partial control, while seven tablets provided complete control of porcupines. Baiting with arsenic trioxide also resulted in 89 % reduction of the porcupine population occupying the treated dens. (author)

Evaluation of a molybdenum assay canister

International Nuclear Information System (INIS)

Yoshizumi, T.T.; Keener, S.J.

1988-01-01

The performance characteristics of a commercial molybdenum assay canister were evaluated. The geometrical variation of the technetium-99m (/sup 99m/Tc) activity reading was studied as a function of the elution volume for the standard vials. It was found that the /sup 99m/Tc canister activity reading was ∼ 5% lower than that of the standard method. This is due to attenuation by the canister wall. However, the effect of the geometric variation on the clinical dose preparation was found to be insignificant. The molybdenum-99 ( 99 Mo) contamination level was compared by two methods: (1) the commercial canister and (2) the standard assay kit. The 99 Mo contamination measurements with the canister indicated consistently lower readings than those with the standard 99 Mo assay kit. The authors conclude that the canister may be used in the clinical settings. However, the user must be aware of the problems and the limitations associated with this canister

Ternary cobalt-molybdenum-zirconium coatings for alternative energies

Science.gov (United States)

Yar-Mukhamedova, Gulmira; Ved', Maryna; Sakhnenko, Nikolay; Koziar, Maryna

2017-11-01

Consistent patterns for electrodeposition of Co-Mo-Zr coatings from polyligand citrate-pyrophosphate bath were investigated. The effect of both current density amplitude and pulse on/off time on the quality, composition and surface morphology of the galvanic alloys were determined. It was established the coating Co-Mo-Zr enrichment by molybdenum with current density increasing up to 8 A dm-2 as well as the rising of pulse time and pause duration promotes the content of molybdenum because of subsequent chemical reduction of its intermediate oxides by hydrogen ad-atoms. It was found that the content of the alloying metals in the coating Co-Mo-Zr depends on the current density and on/off times extremely and maximum Mo and Zr content corresponds to the current density interval 4-6 A dm-2, on-/off-time 2-10 ms. Chemical resistance of binary and ternary coatings based on cobalt is caused by the increased tendency to passivity and high resistance to pitting corrosion in the presence of molybdenum and zirconium, as well as the acid nature of their oxides. Binary coating with molybdenum content not less than 20 at.% and ternary ones with zirconium content in terms of corrosion deep index are in a group ;very proof;. It was shown that Co-Mo-Zr alloys exhibits the greatest level of catalytic properties as cathode material for hydrogen electrolytic production from acidic media which is not inferior a platinum electrode. The deposits Co-Mo-Zr with zirconium content 2-4 at.% demonstrate high catalytic properties in the carbon(II) oxide conversion. This confirms the efficiency of materials as catalysts for the gaseous wastes purification and gives the reason to recommend them as catalysts for red-ox processes activating by oxygen as well as electrode materials for red-ox batteries.

Weldability of molybdenum and its alloy sheet, 1

International Nuclear Information System (INIS)

Matsuda, Fukuhisa; Ushio, Masao; Nakata, Kazuhiro; Edo, Yoshiaki

1979-01-01

Basic weldability of electron-beam melted pure molybdenum has been examined in electron-beam welding in high vacuum and GTA welding in pure and air mixed argon atmospheres by paying attention to weld defects such as hot cracking and porosity in weld metal and also mechanical properties of welded joint in comparison with conventional TZM alloys. The main conclusions obtained were as follows; (1) The weld metals of electron-beam melted pure molybdenum with electron-beam and GTA weldings in pure and air mixed argon atmosphere up to about 1% were almost porosity free. However, large amount of oxygen content of 200 ppm in powder-metallurgy TZM alloy made very porous weld bead in electron-beam welding in high vacuum. Therefore, oxygen content in base metal should be lowered to the minimum, that is, less than 10 ppm, especially in electron-beam welding in high vacuum. (2) Hot cracking occurred in the weld metal of GTA welding when air content in argon atmosphere exceeded about 0.6% for electron-beam melted pure molybdenum and powder metallurgy TZM alloy. In less than 0.26% air, no hot cracking were observed in this experiment. Moreover, in electron-beam welding, no hot cracking was observed in weld metals for both materials. In order to prevent the formation of hot cracking, the purity of welding atmosphere should be kept as high as possible. (3) Joint efficiency of the welded joint of electron-beam melted pure molybdenum with electron-beam welding was 50 to 60% to base metal at room temperature and 500 0 C and almost 100% at 1000 0 C. Those of GTA welds in pure and 0.13% air mixed argon atmospheres were fairly lower than those in electron-beam welding for each testing temperature. (author)

Determination of molybdenum in flotation concentrates by atomic absorption spectrophotometry

International Nuclear Information System (INIS)

Ise, Kazuo

1978-01-01

Molybdenum was determined by atomic absorption spectrophotometry in 0.05 N ammoniacal solution after the decomposition of the concentrate with aqua regia. Negros ore from Philippines was used as a flotation feed, which contained chalcopyrites and calcium-magnesium minerals. Among the metals tested copper, iron and the alkaline earths interfered. Less than 50 ppm of copper yielded lower results for molybdenum. Higher results came out with more than 50 ppm of copper. In the presence of iron and citric acid (0.4 g/100 ml) which is a suppressor for hydroxide formation, a lower estimation resulted for molybdenum. Calcium interfered, lower results by 2 and >10% being obtained with respective 2.5 and 20 ppm of calcium. More than 20 ppm of magnesium behaved similarly. Sodium sulfate (0.5 g/100 ml) served as the suppressor for copper, iron and citric acid; 100 ppm each of copper and iron did not interfere in this way. Interferences due to calcium and magnesium (less than 60 ppm) was able to be masked by the addition of sodium silicate (200 ppm as silica). The analysis of flotation products and synthetic samples consisting of molybdenite, chalcopyrite, calcium chloride and magnesium sulfate revealed that the atomic absorption method can be applied to the analysis of the concentrates for molybdenum with an error of about 2%. (auth.)

Effect of molybdenum addition on metastability of cubic γ-uranium

International Nuclear Information System (INIS)

Sinha, V.P.; Hegde, P.V.; Prasad, G.J.; Dey, G.K.; Kamath, H.S.

2010-01-01

Over the years U 3 Si 2 compound dispersed in aluminium matrix has been used successfully as the potential low enriched uranium (LEU 235 ) base dispersion fuel for use in new research and test reactors and also for converting high enriched uranium (HEU > 85%U 235 ) cores to LEU for most of the existing research and test reactors world over, though maximum 4.8 g U cm -3 density is achievable with U 3 Si 2 -Al dispersion fuel. To achieve a uranium density of 8.0-9.0 g U cm -3 in dispersion fuel with aluminium as matrix material, it is required to use γ-stabilized uranium metal powders. At Bhabha Atomic Research Centre (BARC), R and D efforts are on to develop these high density uranium base alloys. This paper describes the alloying behaviour of uranium with varying amount of molybdenum. The U-Mo alloys with different molybdenum content have been prepared by using an induction melting furnace with uranium and molybdenum metal pellets as starting materials. U-Mo alloys with different molybdenum content were characterized by X-ray diffraction (XRD) for phase identification and lattice parameter measurements. The optical microstructure of different U-Mo alloy composition has also been discussed in this paper. Quantitative image analysis was also carried out to determine the amount of various phases in each composition.

AC conductivity and dielectric properties of bulk tungsten trioxide (WO3)

Science.gov (United States)

El-Nahass, M. M.; Ali, H. A. M.; Saadeldin, M.; Zaghllol, M.

2012-11-01

AC conductivity and dielectric properties of tungsten trioxide (WO3) in a pellet form were studied in the frequency range from 42 Hz to 5 MHz with a variation of temperature in the range from 303 K to 463 K. AC conductivity, σac(ω) was found to be a function of ωs where ω is the angular frequency and s is the frequency exponent. The values of s were found to be less than unity and decrease with increasing temperature, which supports the correlated barrier hopping mechanism (CBH) as the dominant mechanism for the conduction in WO3. The dielectric constant (ε‧) and dielectric loss (ε″) were measured. The Cole-Cole diagram determined complex impedance for different temperatures.

Air-segmented continuous-flow analysis for molybdenum in various geochemical samples

International Nuclear Information System (INIS)

Harita, Y.; Sugiyama, M.; Hori, T.

2003-01-01

An air-segmented continuous-flow method has been developed for the determination of molybdenum at ultra trace levels using the catalytic effect of molybdate during the oxidation of L-ascorbic acid by hydrogen peroxide. Incorporation of an on-line ion exchange column improved the tolerance limit for various ions. The detection limits with and without the column were 64 pmol L m1 and 17 pmol L m1 , and the reproducibilities at 10 nmol L m1 were 2.1 % and 0.2 %, respectively. The proposed method was applied to the determination of molybdenum in seawater and lake water as well as in rock and sediment samples. This method has the highest sensitivity among the available literature to our knowledge, and is also convenient for routine analysis of molybdenum in various natural samples. (author)

Direct determination of molybdenum in seawater by adsorption cathodic stripping square-wave voltammetry.

Science.gov (United States)

Sun, Y C; Mierzwa, J; Lan, C R

2000-06-30

A reliable and very sensitive procedure for the determination of trace levels of molybdenum in seawater is proposed. The complex of molybdenum with 8-hydroxyquinoline (Oxine) is analyzed by cathodic stripping square-wave voltammetry based on the adsorption collection onto a hanging mercury drop electrode (HMDE). This procedure of molybdenum determination was found to be more favorable than differential pulse cathodic stripping voltammetry because of inherently faster scan rate and much better linearity obtained through the one-peak (instead of one-of-two peaks) calibration. The variation of polarographic peak and peak current with a pH, adsorption time, adsorption potential, and some instrumental parameters such as scan rate and pulse height were optimized. The alteration of polarographic wave and its likely mechanism are also discussed. The relationship between peak current and molybdenum concentration is linear up to 150 mug l(-1). Under the optimal analytical conditions, the determination limit of 0.5 mug l(-1) Mo was reached after 60 s of the stirred collection. The estimated detection limit is better than 0.1 mug l(-1) of Mo. The applicability of this method to analysis of seawater was assessed by the determination of molybdenum in two certified reference seawater samples (CASS-2 and NASS-2) and the comparison of the analytical results for real seawater samples (study on a vertical distribution of Mo in the seawater column) with the results obtained by Zeeman-corrected electrothermal atomization atomic absorption spectrometry (Zeeman ETAAS). A good agreement between two used methods of molybdenum determination was obtained.

Study of arsenic and molybdenum retention in organism during hydrotherapy by neutron activation analysis

International Nuclear Information System (INIS)

Irigaray, J.L.; Mannou, B.; Pepin, D.; Fauquert, J.L.

1989-01-01

At La Bourboule (France), arsenic and molybdenum are contained in high concentrations in the spring water used for hydrotherapy. Thermal neutron activation analysis was applied to determine arsenic and molybdenum penetration into the organism for the first time. The results obtained with children, men and rabbits are similar. The chronology of the absorption of arsenic and molybdenum in blood and urine during the treatment is in good accordance with the medical therapeutic observations. (author) 10 refs.; 10 figs.; 10 tabs

High-resolution K-shell spectra from laser excited molybdenum plasmas

Directory of Open Access Journals (Sweden)

Szabo C.I.

2013-11-01

Full Text Available X-ray spectra from Molybdenum plasmas were recorded by a Cauchois-type cylindrically bent Transmission Crystal Spectrometer (TCS. The absolutely calibrated spectrometer provides an unprecedented resolution of inner shell transitions (K x-ray radiation. This tool allows us to resolve individual lines from different charge states existing inside the laser-produced plasma. The inner shell transitions from highly charged Molybdenum shown in this report have never been resolved before in such detail in a laser-produced plasma.

SEALING ABILITY OF MINERAL TRIOXIDE AGGREGATE, CALCIUM PHOSPHATE CEMENT, AND GLASS IONOMER CEMENT IN THE REPAIR OF FURCATION PERFORATIONS

Directory of Open Access Journals (Sweden)

Prabath Singh

2013-01-01

Full Text Available Objectives: The purpose of this study was to evaluate the in vitro sealing ability of three repair materials. Mineral trioxide aggregate (MTA; Group A, calcium phosphate cement (CPC; Group B, and light cured glass ionomer cement (GIC; Group C when used to repair the perforation created in the pulpal floor of fifty extracted human permanent molars. Materials and methods: Preparation of access openings and furcation perforations were done, and the teeth divided into five experimental groups (A, B, C including two controls (D, E with ten samples in each group randomly. Following the repair procedure, the pulp chambers and access openings were filled with composite resin and immersed in 2% methylene blue solution for 48 hours. The teeth were sectioned longitudinally and the linear dye penetration measured under a stereo­microscope. Results: The comparison of the linear length of micro-leakage (mm among the experimental groups revealed no significant difference (p = 0.332. On calculating the percentage of depth of leakage to the total length of the perforation, it was observed that the mean leakage was 35.5% in Group A, 53.6% in Group B and the highest, 87.5% in Group C. The mean of leakage percentage was statistically significant by Kruskal-Wallis test (p = 0.003. The results indicated that the dye penetration used as furcation perforation repair material was least with mineral trioxide aggregate. Comparing the depth of penetration of dye, 50% of the Group A samples showed less than 25% of depth penetration. While 40% of Group B cases had more than 50% dye penetration. In our study, all Group C teeth had ≥ 50% dye penetration. Conclusions: The present study indicated that GIC had the greatest dye penetration followed by CPC and MTA. Mineral trioxide aggregate and calcium phosphate cement had comparatively better sealing ability than glass ionomer cement.

Separation of molybdenum(VI) by extraction with n-octylaniline from hydrochloric acid medium

International Nuclear Information System (INIS)

Sawant, S.S.; Anuse, M.A.; Chavan, M.B.

1997-01-01

N-Octylaniline in benzene was used for the extractive separation of molybdenum(VI) from hydrochloric acid medium. Molybdenum(VI) was extracted quantitatively from 10 ml aqueous solution 1.5M in hydrochloric acid and 10M in lithium chloride into 10 ml of 10% n-octylaniline in benzene. It was stripped from the organic phase with 5% aqueous ammonia solution and estimated spectrophotometrically with thiocyanate at 465 nm. The interference of various ions has been studied in detail and conditions have been established for the determination of molybdenum(VI) in synthetic mixtures and alloy samples. (author)

Nitrogen incorporation in sputter deposited molybdenum nitride thin films

Energy Technology Data Exchange (ETDEWEB)

Stöber, Laura, E-mail: laura.stoeber@tuwien.ac.at; Patocka, Florian, E-mail: florian.patocka@tuwien.ac.at; Schneider, Michael, E-mail: michael.schneider@tuwien.ac.at; Schmid, Ulrich, E-mail: ulrich.e366.schmid@tuwien.ac.at [Institute of Sensor and Actuator Systems, TU Wien, Gußhausstraße 27-29, A-1040 Vienna (Austria); Konrath, Jens Peter, E-mail: jenspeter.konrath@infineon.com; Haberl, Verena, E-mail: verena.haberl@infineon.com [Infineon Technologies Austria AG, Siemensstraße 2, 9500 Villach (Austria)

2016-03-15

In this paper, the authors report on the high temperature performance of sputter deposited molybdenum (Mo) and molybdenum nitride (Mo{sub 2}N) thin films. Various argon and nitrogen gas compositions are applied for thin film synthetization, and the amount of nitrogen incorporation is determined by Auger measurements. Furthermore, effusion measurements identifying the binding conditions of the nitrogen in the thin film are performed up to 1000 °C. These results are in excellent agreement with film stress and scanning electron microscope analyses, both indicating stable film properties up to annealing temperatures of 500 °C.

Molybdenum-containing acidic catalysts to convert cellulosic biomass to glycolic acid

KAUST Repository

Han, Yu

2014-09-30

Embodiments of the present invention include methods and compositions related to catabolic conversion of cellulosic biomass to glycolic acid using molybdenum-containing acidic catalysts. The invention includes the use of heteropoly and isopoly acids and salts as the molybdenum-containing multi-functional catalysts for biomass conversion. In embodiments of the invention, the reactions employ successive hydrolysis, retro-aldol fragmentation, and selective oxidation in a noble metal-free system.

Note: Laser-cut molybdenum grids for a retarding field energy analyzer

Science.gov (United States)

Landheer, K.; Kobelev, A. A.; Smirnov, A. S.; Bosman, J.; Deelen, S.; Rossewij, M.; de Waal, A. C.; Poulios, I.; Benschop, A. F.; Schropp, R. E. I.; Rath, J. K.

2017-06-01

A retarding field energy analyzer (RFEA) with grids created by laser-cutting a honeycomb mesh in a 50 μm thick molybdenum foil is presented. The flat grids span an area of 1 cm2 and have high transmission (20 μm wide walls between 150 μm wide meshes). The molybdenum grids were tested in a 3-grid RFEA configuration with an analyzer depth of 0.87 mm.

Hydrothermal synthesis of electrode materials pyrochlore tungsten trioxide film

Science.gov (United States)

Guo, Jingdong; Li, Yingjeng James; Stanley Whittingham, M.

Hydrothermal synthesis methods have been successfully used to prepare new transition-metal oxides for cathodes in electrochemical devices such as lithium batteries and electrochromic windows. The tungsten oxides were the first studied, but the method has been extended to the oxides of molybdenum, vanadium and manganese. Sodium tungsten oxide films with the pyrochlore structure have been prepared on gold/alumina and indium-doped tin oxide substrates. These films reversibly and rapidly intercalate lithium and hydrogen ions.

Growth and surface characterization of sputter-deposited molybdenum oxide thin films

Energy Technology Data Exchange (ETDEWEB)

Ramana, C.V. [Nanoscience and Surface Chemistry Laboratory, Department of Geological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States)]. E-mail: ramanacv@umich.edu; Atuchin, V.V. [Laboratory of Optical Materials and Structures, Institute of Semiconductor Physics, SB RAS, Novosibirsk 630090 (Russian Federation); Kesler, V.G. [Technical Centre, Institute of Semiconductor Physics, SB RAS, Novosibirsk 630090 (Russian Federation); Kochubey, V.A. [Laboratory of Optical Materials and Structures, Institute of Semiconductor Physics, SB RAS, Novosibirsk 630090 (Russian Federation); Pokrovsky, L.D. [Laboratory of Optical Materials and Structures, Institute of Semiconductor Physics, SB RAS, Novosibirsk 630090 (Russian Federation); Shutthanandan, V. [Environmental Molecular Sciences Laboratory, Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Becker, U. [Nanoscience and Surface Chemistry Laboratory, Department of Geological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Ewing, R.C. [Nanoscience and Surface Chemistry Laboratory, Department of Geological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States)

2007-04-15

Molybdenum oxide thin films were produced by magnetron sputtering using a molybdenum (Mo) target. The sputtering was performed in a reactive atmosphere of an argon-oxygen gas mixture under varying conditions of substrate temperature (T {sub s}) and oxygen partial pressure (pO{sub 2}). The effect of T {sub s} and pO{sub 2} on the growth and microstructure of molybdenum oxide films was examined in detail using reflection high-energy electron diffraction (RHEED), Rutherford backscattering spectrometry (RBS), energy-dispersive X-ray spectrometry (EDS), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) measurements. The analyses indicate that the effect of T {sub s} and pO{sub 2} on the microstructure and phase of the grown molybdenum oxide thin films is remarkable. RHEED and RBS results indicate that the films grown at 445 deg. C under 62.3% O{sub 2} pressure were stoichiometric and polycrystalline MoO{sub 3}. Films grown at lower pO{sub 2} were non-stoichiometric MoO {sub x} films with the presence of secondary phase. The microstructure of the grown Mo oxide films is discussed and conditions were optimized to produce phase pure, stoichiometric, and highly textured polycrystalline MoO{sub 3} films.

Peculiarities of phase transformations in molybdenum-silicon system under ion bombardment

International Nuclear Information System (INIS)

Gurskij, L.I.; Zelenin, V.A.; Bobchenok, Yu.L.

1984-01-01

The problems of effect of ion bombardment and thermal treatment on the mechanisms of formation of transition layers and structural transformations in the molybdenum-silicon system, where the interface is subjected to ion bombardment through a film of molybdenum, are considered. The method of electron diffraction analysis has been applied to establish that at the molybdenum-silicon interface a transitional region appears during irradiation which has a semiamorphous structure at the doses up to 8x10 14 ion/cm 2 , while at higher doses it transforms into polycrystalline intermediate layer which consists of MoB and the compound close in composition to MoSisub(0.65). Due to thermal treatment for 60873 K a large-grain phase (Mo 3 Si+MoSi 2 ) appears in the transition layer below which a large-grain silicon layer is placed

Development of a low-permeability glass--ceramic to seal to molybdenum

International Nuclear Information System (INIS)

Eagan, R.J.

1975-03-01

This report describes the development of low-permeability glass-ceramics which can be sealed directly to molybdenum for the purpose of producing long-life vacuum tubes. Low permeability to helium and thermal expansion match to molybdenum are the bases upon which particular glass-ceramic compositions were selected and developed. The fabrication of tube envelopes using glass-ceramics is simplified when compared to conventional ceramic/metal tubes and these melting and sealing techniques are presented

An analytic study of molybdenum disulfide nanofluids using the modern approach of Atangana-Baleanu fractional derivatives

Science.gov (United States)

Ali Abro, Kashif; Hussain, Mukkarum; Mahmood Baig, Mirza

2017-10-01

The significance of the different shapes of molybdenum disulfide nanoparticles contained in ethylene glycol has recently attracted researchers, because of the numerical or experimental analyses on the shapes of molybdenum disulfide and the lack of fractionalized analytic approaches. This work is dedicated to examining the shape impacts of molybdenum disulfide nanofluids in the mixed convection flow with magnetic field and a porous medium. Ethylene glycol is chosen as the base fluid in which molybdenum disulfide nanoparticles are suspended. Non-spherically shaped molybdenum disulfide nanoparticles, namely, platelet, blade, cylinder and brick, are utilized in this analysis. The modeling of the problem is characterized by employing the modern approach of Atangana-Baleanu fractional derivatives and the governing partial differential equations are solved via Laplace transforms with inversion. Solutions are obtained for temperature distribution and velocity field and expressed in terms of compact form of M-function, Mba(T) . In the end, a figures are drawn to compare the different non-spherically shaped molybdenum disulfide nanoparticles. Furthermore, the Atangana-Baleanu fractional derivatives model has been compared with ordinary derivatives models and discussed graphically by setting various rheological parameters.

Electron transfer kinetics on natural crystals of MoS2 and graphite.

Science.gov (United States)

Velický, Matěj; Bissett, Mark A; Toth, Peter S; Patten, Hollie V; Worrall, Stephen D; Rodgers, Andrew N J; Hill, Ernie W; Kinloch, Ian A; Novoselov, Konstantin S; Georgiou, Thanasis; Britnell, Liam; Dryfe, Robert A W

2015-07-21

Here, we evaluate the electrochemical performance of sparsely studied natural crystals of molybdenite and graphite, which have increasingly been used for fabrication of next generation monolayer molybdenum disulphide and graphene energy storage devices. Heterogeneous electron transfer kinetics of several redox mediators, including Fe(CN)6(3-/4-), Ru(NH3)6(3+/2+) and IrCl6(2-/3-) are determined using voltammetry in a micro-droplet cell. The kinetics on both materials are studied as a function of surface defectiveness, surface ageing, applied potential and illumination. We find that the basal planes of both natural MoS2 and graphite show significant electroactivity, but a large decrease in electron transfer kinetics is observed on atmosphere-aged surfaces in comparison to in situ freshly cleaved surfaces of both materials. This is attributed to surface oxidation and adsorption of airborne contaminants at the surface exposed to an ambient environment. In contrast to semimetallic graphite, the electrode kinetics on semiconducting MoS2 are strongly dependent on the surface illumination and applied potential. Furthermore, while visibly present defects/cracks do not significantly affect the response of graphite, the kinetics on MoS2 systematically accelerate with small increase in disorder. These findings have direct implications for use of MoS2 and graphene/graphite as electrode materials in electrochemistry-related applications.

Electroplating and stripping copper on molybdenum and niobium

Science.gov (United States)

Power, J. L.

1978-01-01

Molybdenum and niobium are often electroplated and subsequently stripped of copper. Since general standard plating techniques produce poor quality coatings, general procedures have been optimized and specified to give good results.

Generalized molybdenum oxide surface chemical state XPS determination via informed amorphous sample model

Energy Technology Data Exchange (ETDEWEB)

Baltrusaitis, Jonas, E-mail: job314@lehigh.edu [Department of Chemical Engineering, Lehigh University, B336 Iacocca Hall, 111 Research Drive, Bethlehem, PA 18015 (United States); PhotoCatalytic Synthesis group, MESA+ Institute for Nanotechnology, Faculty of Science and Technology, University of Twente, Meander 229, P.O. Box 217, 7500 AE Enschede (Netherlands); Mendoza-Sanchez, Beatriz [CRANN, Chemistry School, Trinity College Dublin, Dublin (Ireland); Fernandez, Vincent [Institut des Matériaux Jean Rouxel, 2 rue de la Houssinière, BP 32229, F-44322 Nantes Cedex 3 (France); Veenstra, Rick [PhotoCatalytic Synthesis group, MESA+ Institute for Nanotechnology, Faculty of Science and Technology, University of Twente, Meander 229, P.O. Box 217, 7500 AE Enschede (Netherlands); Dukstiene, Nijole [Department of Physical and Inorganic Chemistry, Kaunas University of Technology, Radvilenu pl. 19, LT-50254 Kaunas (Lithuania); Roberts, Adam [Kratos Analytical Ltd, Trafford Wharf Road, Wharfside, Manchester, M17 1GP (United Kingdom); Fairley, Neal [Casa Software Ltd, Bay House, 5 Grosvenor Terrace, Teignmouth, Devon TQ14 8NE (United Kingdom)

2015-01-30

Highlights: • We analyzed and modeled spectral envelopes of complex molybdenum oxides. • Molybdenum oxide films of varying valence and crystallinity were synthesized. • MoO{sub 3} and MoO{sub 2} line shapes from experimental data were created. • Informed amorphous sample model (IASM) developed. • Amorphous molybdenum oxide XPS envelopes were interpreted. - Abstract: Accurate elemental oxidation state determination for the outer surface of a complex material is of crucial importance in many science and engineering disciplines, including chemistry, fundamental and applied surface science, catalysis, semiconductors and many others. X-ray photoelectron spectroscopy (XPS) is the primary tool used for this purpose. The spectral data obtained, however, is often very complex and can be subject to incorrect interpretation. Unlike traditional XPS spectra fitting procedures using purely synthetic spectral components, here we develop and present an XPS data processing method based on vector analysis that allows creating XPS spectral components by incorporating key information, obtained experimentally. XPS spectral data, obtained from series of molybdenum oxide samples with varying oxidation states and degree of crystallinity, were processed using this method and the corresponding oxidation states present, as well as their relative distribution was elucidated. It was shown that monitoring the evolution of the chemistry and crystal structure of a molybdenum oxide sample due to an invasive X-ray probe could be used to infer solutions to complex spectral envelopes.

Selective emission multilayer coatings for a molybdenum thermophotovoltaic radiator

Science.gov (United States)

Cockeram, Brian Vern

2004-01-27

Multilayer coating designs have been developed to provide selective emission for a molybdenum thermophotovoltaic (TPV) radiator surface. These coatings increase the surface emissivity of a molybdenum TPV radiator substrate in the wavelength range that matches the bandgap of the TPV cells to increase the power density of the TPV system. Radiator emission at wavelengths greater than the bandgap energy of the TPV cells is greatly reduced through the use of these coatings, which significantly increases the efficiency of the TPV system. The use of this coating greatly improves the performance of a TPV system, and the coating can be tailored to match the bandgap of any practical TPV system.

Effect of molybdenum on structure, microstructure and mechanical properties of biomedical Ti-20Zr-Mo alloys.

Science.gov (United States)

Kuroda, Pedro Akira Bazaglia; Buzalaf, Marília Afonso Rabelo; Grandini, Carlos Roberto

2016-10-01

Titanium has an allotropic transformation around 883°C. Below this temperature, the crystalline structure is hexagonal close-packed (α phase), changing to body-centered cubic (β phase). Zirconium has the same allotropic transformation around 862°C. Molybdenum has body-centered cubic structure, being a strong β-stabilizer for the formation of titanium alloys. In this paper, the effect of substitutional molybdenum was analyzed on the structure, microstructure and selected mechanical properties of Ti-20Zr-Mo (wt%) alloys to be used in biomedical applications. The samples were prepared by arc-melting and characterized by x-ray diffraction with subsequent refinement by the Rietveld method, optical and scanning electron microscopy. The mechanical properties were analyzed by Vickers microhardness and dynamic elasticity modulus. X-ray measurements and Rietveld analysis revealed the presence of α' phase without molybdenum, α'+α″ phases with 2.5wt% of molybdenum, α″+β phases with 5 and 7.5wt% of molybdenum, and only β phase with 10wt% of molybdenum. These results were corroborated by microscopy results, with a microstructure composed of grains of β phase and lamellae and needles of α' and α″ phase in intra-grain the region. The hardness of the alloy was higher than the commercially pure titanium, due to the action of zirconium and molybdenum as hardening agents. The samples have a smaller elasticity modulus than the commercially pure titanium. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of liming on the molybdenum content in the root and leaf of ...

African Journals Online (AJOL)

Three liming treatments were employed (1, 3 and 4 t/ha CaCO3). The liming operation used on pseudogley induced a statistically significant increase in molybdenum ion absorption into the root system of tomato. Independently from the aforementioned, the values for the root and leaf molybdenum content of tomato in each ...

Influence of molybdenum content on transformation behavior of high performance bridge steel during continuous cooling

International Nuclear Information System (INIS)

Chen, Jun; Tang, Shuai; Liu, Zhenyu; Wang, Guodong

2013-01-01

Highlights: ► The bainite transformation field was refined. ► The empirical equation to estimate the GF s was established. ► Transformation behavior was studied with serially increasing Mo addition. ► The molybdenum content can be lowered as the cooling rate is increased. ► GF transformation field is also shifted to right by increasing Mo content. - Abstract: The continuous-cooling-transformation (CCT) diagrams of high performance bridge steel with different molybdenum content were plotted by means of a combined method of dilatometry and metallography. The results show that the molybdenum addition of 0.17 wt% does not noticeably alter the transformation behavior, whereas 0.38 wt% significantly. In addition, the molybdenum addition of 0.38 wt% completely eliminates the formation of polygonal ferrite (PF) and significantly lower the granular ferrite (GF) transformation starting temperatures throughout the range of cooling rates studied. At lower cooling rates, with the increase of the molybdenum content, the martensite/austenite (M/A) constituents are noticeably refined, whereas the effects are not obvious at higher cooling rates. Moreover, the molybdenum addition of 0.38 wt% can significantly increase the Vickers hardness, but the Vickers hardness increments (by comparison of Mo-0.17wt% steel and Mo-0.38wt% steel) are sharply reduced at the cooling rate of 30 °C/s, indicating that at higher cooling rate, the molybdenum usage can be saved and the higher strengthen can be also gained. It could be found the GF transformation starting temperature is linear with the cooling rate. The empirical equation was established to calculate GF transformation starting temperatures, and the calculated values are in good agreement with measured ones

Principal component analysis of NEXAFS spectra for molybdenum speciation in hydrotreating catalysts

International Nuclear Information System (INIS)

Faro Junior, Arnaldo da C.; Rodrigues, Victor de O.; Eon, Jean-G.; Rocha, Angela S.

2010-01-01

Bulk and supported molybdenum based catalysts, modified by nickel, phosphorous or tungsten were studied by NEXAFS spectroscopy at the Mo L III and L II edges. The techniques of principal component analysis (PCA) together with a linear combination analysis (LCA) allowed the detection and quantification of molybdenum atoms in two different coordination states in the oxide form of the catalysts, namely tetrahedral and octahedral coordination. (author)

Modeling the homogenization kinetics of as-cast U-10wt% Mo alloys

Energy Technology Data Exchange (ETDEWEB)

Xu, Zhijie, E-mail: zhijie.xu@pnnl.gov [Computational Mathematics Group, Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Joshi, Vineet [Energy Processes & Materials Division, Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Hu, Shenyang [Reactor Materials & Mechanical Design, Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Paxton, Dean [Nuclear Engineering and Analysis Group, Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Lavender, Curt [Energy Processes & Materials Division, Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Burkes, Douglas [Nuclear Engineering and Analysis Group, Pacific Northwest National Laboratory, Richland, WA 99352 (United States)

2016-04-01

Low-enriched U-22at% Mo (U–10Mo) alloy has been considered as an alternative material to replace the highly enriched fuels in research reactors. For the U–10Mo to work effectively and replace the existing fuel material, a thorough understanding of the microstructure development from as-cast to the final formed structure is required. The as-cast microstructure typically resembles an inhomogeneous microstructure with regions containing molybdenum-rich and -lean regions, which may affect the processing and possibly the in-reactor performance. This as-cast structure must be homogenized by thermal treatment to produce a uniform Mo distribution. The development of a modeling capability will improve the understanding of the effect of initial microstructures on the Mo homogenization kinetics. In the current work, we investigated the effect of as-cast microstructure on the homogenization kinetics. The kinetics of the homogenization was modeled based on a rigorous algorithm that relates the line scan data of Mo concentration to the gray scale in energy dispersive spectroscopy images, which was used to generate a reconstructed Mo concentration map. The map was then used as realistic microstructure input for physics-based homogenization models, where the entire homogenization kinetics can be simulated and validated against the available experiment data at different homogenization times and temperatures.

Effect of Blood Contamination on Marginal Adaptation and Surface Microstructure of Mineral Trioxide Aggregate: A SEM Study

OpenAIRE

Amin Salem Milani; Saeed Rahimi; Mohammad Froughreyhani; Mahdi Vahid Pakdel

2013-01-01

Background and aims. In various clinical situations, mineral trioxide aggregate (MTA) may come into direct contact or even be mixed with blood. The aim of the present study was to evaluate the effect of exposure to blood on marginal adaptation and surface microstructure of MTA. Materials and methods. Thirty extracted human single-rooted teeth were used. Standard root canal treatment was carried out. Root-ends were resected, and retrocavities were prepared. The teeth were randomly ...

Molybdenum carbide coating electrodeposited from molten fluoride bath

International Nuclear Information System (INIS)

Topor, D.C.; Selman, J.R.

1987-01-01

Molybdenum carbide has been recently considered as a candidate material for the protection of common steel-based substrates in high-temperature high-sulfur activity applications. Methods to produce coatings of materials such as Mo/sub 2/C are scarce and only the electrodeposition from molten salts can yield dense, pore-free layers on various metallic profiles. Recently Stern reported the deposition of a Mo/sub 2/C coating on nickel substrate form, FLINAK + K/sub 2/MoCl/sub 6/ + Na/sub 2/CO/sub 3/ mixture at 850 0 C. Electrodeposition of Mo/sub 2/C on a cathode surface proceeds according to a rather complicated mechanism which may involve simultaneous reduction of carbonate to C, of molybdate to Mo and a subsequent chemical reaction between both species. The deposit grows further as a coherent coating. Reduction of CO/sub 2/ or carbonate to carbon in a fused salt medium could follow different paths but Li/sup +/ ions or other highly polarizing ions must be present. A similar situation in which a polyatomic anion discharges at the cathode is encountered when molybdates are used as source of molybdenum. In fluoride melts the chemistry of Mo(VI) species is considered to be much simpler due to the hard fluoride ions. These ions form strong complexes with molybdenum and the resulting solution is more stable

The determination of molybdenum and tungsten in resin by x-ray-fluorescence spectrometry

International Nuclear Information System (INIS)

Eddy, B.T.

1985-01-01

This report describes a method using X-ray-fluorescence spectrometry for the determination of molybdenum and tungsten in ion-exchange resins. The dried resin is milled with sand, binder, and an internal-standard mixture before being briquetted. Niobium and zinc are used as the internal standards for molybdenum and tungsten respectively. Intensity measurements are made with the gold anode tube. Corrections are made for the interference of the Mo Kα analytical line on the background intensities used for the Mo Kα and Nb Kα lines. The precision of the analysis for molybdenum ranges from a relative standard deviation 0,02 at 5 mg/g to 0.045 at 55μg/g; for tungsten, the relative standard deviation ranges from 0,04 at 5 mg/g to 0,055 at 55μg/g. The limits of determination in the original resin sample were found to be 40μg/g for molybdenum and 80μg/g for tungsten. The laboratory method is given in an appendix

Hexavalent Molybdenum Reduction to Mo-Blue by a Sodium-Dodecyl-Sulfate-Degrading Klebsiella oxytoca Strain DRY14

Directory of Open Access Journals (Sweden)

M. I. E. Halmi

2013-01-01

Full Text Available Bacteria with the ability to tolerate, remove, and/or degrade several xenobiotics simultaneously are urgently needed for remediation of polluted sites. A previously isolated bacterium with sodium dodecyl sulfate- (SDS- degrading capacity was found to be able to reduce molybdenum to the nontoxic molybdenum blue. The optimal pH, carbon source, molybdate concentration, and temperature supporting molybdate reduction were pH 7.0, glucose at 1.5% (w/v, between 25 and 30 mM, and 25°C, respectively. The optimum phosphate concentration for molybdate reduction was 5 mM. The Mo-blue produced exhibits an absorption spectrum with a maximum peak at 865 nm and a shoulder at 700 nm. None of the respiratory inhibitors tested showed any inhibition to the molybdenum-reducing activity suggesting that the electron transport system of this bacterium is not the site of molybdenum reduction. Chromium, cadmium, silver, copper, mercury, and lead caused approximately 77, 65, 77, 89, 80, and 80% inhibition of the molybdenum-reducing activity, respectively. Ferrous and stannous ions markedly increased the activity of molybdenum-reducing activity in this bacterium. The maximum tolerable concentration of SDS as a cocontaminant was 3 g/L. The characteristics of this bacterium make it a suitable candidate for molybdenum bioremediation of sites cocontaminated with detergent pollutant.

X-ray target with substrate of molybdenum alloy

International Nuclear Information System (INIS)

Hirsch, H.H.

1980-01-01

Rotary targets for x-ray tubes are provided comprising a molybdenum base body alloyed with a stabilizing proportion of iron, silicon, cobalt, tantalum, niobium, hafnium, stable metal oxide, or a mixture of the preceding

High-strength chromium--molybdenum rails

International Nuclear Information System (INIS)

Smith, Y.E.; Sawhill, J.M. Jr.; Cias, W.W.; Eldis, G.T.

1976-01-01

A laboratory study was conducted with the aim of developing an as-rolled rail of over 100 ksi (689 N/mm 2 ) yield strength. A series of compositions providing both pearlitic and bainitic microstructures was evaluated. A fine pearlitic structure was developed in a 0.73 percent C -- 0.83 percent Mn -- 0.16 percent Si -- 0.75 percent Cr -- 0.21 percent Mo steel by simulating the mill cooling rate of 132-lb/yd (65.5-kg/m) rail. Two 100-ton commercial heats were made of this approximate composition and processed into 132-lb/yd (65.5-kg/m) rail. Samples tested in the laboratory ranged from 109 to 125 ksi (750 to 860 N/mm 2 ) in yield strength. The chromium-molybdenum rails also exhibited excellent fracture toughness and fatigue properties. Sections of the rail were joined by both flash-butt welding and thermite welding. The hardness peaks produced in the flash-butt welds could be reduced by applying either a postweld current or an induction heating cycle. The high-strength chromium-molybdenum rails have been in service for over eight months in curved sections of an ore railway that carries over 55 million gross long tons per year. 7 tables, 18 figs

Photoresist removal using gaseous sulfur trioxide cleaning technology

Science.gov (United States)

Del Puppo, Helene; Bocian, Paul B.; Waleh, Ahmad

1999-06-01

A novel cleaning method for removing photoresists and organic polymers from semiconductor wafers is described. This non-plasma method uses anhydrous sulfur trioxide gas in a two-step process, during which, the substrate is first exposed to SO3 vapor at relatively low temperatures and then is rinsed with de-ionized water. The process is radically different from conventional plasma-ashing methods in that the photoresist is not etched or removed during the exposure to SO3. Rather, the removal of the modified photoresist takes place during the subsequent DI-water rinse step. The SO3 process completely removes photoresist and polymer residues in many post-etch applications. Additional advantages of the process are absence of halogen gases and elimination of the need for other solvents and wet chemicals. The process also enjoys a very low cost of ownership and has minimal environmental impact. The SEM and SIMS surface analysis results are presented to show the effectiveness of gaseous SO3 process after polysilicon, metal an oxide etch applications. The effects of both chlorine- and fluorine-based plasma chemistries on resist removal are described.

Concentrations of boron, molybdenum, and selenium in chinook salmon

Science.gov (United States)

Hamilton, Steven J.; Wiedmeyer, Raymond H.

1990-01-01

The concentrations of boron, molybdenum, and selenium in young chinook salmon Oncorhynchus tshawytscha were determined in three partial life cycle chronic toxicity studies. In each study, fish were exposed to a mixture of boron, molybdenum, selenate, and selenite in the proportions found in subsurface agricultural drainage water in the basin of the San Joaquin Valley, California. Tests were conducted in well water and in site-specific fresh and brackish waters. No boron or molybdenum was detected in fish exposed to concentrations as high as 6,046 μg boron/L and 193 μg molybdenum/L for 90 d in well water or fresh water; however, whole-body concentrations of selenium increased with increasing exposure concentrations in well water and fresh water, but not in brackish water. Concentrations of selenium in chinook salmon were strongly correlated with reduced survival and growth of fish in well water and with reduced survival in a 15-d seawater challenge test of fish from fresh water. Concentrations of selenium in fish seemed to reach a steady state after 60 d of exposure in well water or fresh water. Fish in brackish water had only background concentrations of selenium after 60 d of exposure, and no effects on survival and growth in brackish water or on survival in a 10-d seawater challenge test were exhibited. This lack of effect in brackish water was attributed to initiation of the study with advanced fry, which were apparently better able to metabolize the trace element mixture than were the younger fish used in studies with well water and fresh water. In all three experimental waters, concentration factors (whole-body concentration/waterborne concentration) for selenium decreased with increasing exposure concentrations, suggesting decreased uptake or increased excretion, or both, of selenium at the higher concentrations.

Spectrophotometric flow injection catalytic determination of molybdenum in plant digest using ion exchange resin

International Nuclear Information System (INIS)

Pessenda, L.C.R.

1987-03-01

A spectrophotometric flow injection analytical method based on the catalytic action of molybdenum on the oxidation of iodide by hydrogen peroxide in acidic medium is proposed for the molybdenum determination in plant digests. A cation exchange resin column is incorporated into a flow injection system for removal of interferents. The following system variables were investigated and optimized: reagent concentrations, sample injection volume, mixing and reaction coil lengths, temperature, sampling time, pumping rate and concentration of eluting agents. The effects of interfering species and of the acidity of samples on the molybdenum retention by the ion exchange resin column were investigated. The proposed method is characterized by good precision (r.s.d. (2.0%), a sampling rate of about 40 samples per hour, and permits the determination of molybdenum in plant digests in the range 1.0 to 40.0 μg/l. The results compare well with those obtained by graphite furnace atomic absorption spectrometry. (author) [pt

Synthesis of borides in molybdenum implanted by B+ ions under thermal and electron annealing

International Nuclear Information System (INIS)

Kazdaev, Kh.R.; Akchulakov, M.T.; Bayadilov, E.M.; Ehngel'ko, V.I.; Lazarenko, A.V.; Chebukov, E.S.

1989-01-01

The possibility of formation of borides in the near surface layers of monocrystalline molybdenum implanted by boron ions at 35 keV energy under thermal and pulsed electron annealing by an electon beam at 140 keV energy is investigated. It is found that implantation of boron ions into molybdenum with subsequent thermal annealing permits to produce both molybdenum monoboride (α-MoB) and boride (γ-Mo 2 B) with rather different formation mechanisms. Formation of the α-MoB phase occurs with the temperature elevation from the centers appeared during implantation, while the γ-Mo 2 B phase appears only on heating the implanted layers up to definite temperature as a result of the phase transformation of the solid solution into a chemical compound. Pulsed electron annealing instead of thermal annealing results mainly in formation of molybdenum boride (γ-Mo 2 B), the state of structure is determined by the degree of heating of implanted layers and their durable stay at temperatures exceeding the threshold values

Atomic Layer-Deposited Molybdenum Oxide/Carbon Nanotube Hybrid Electrodes: The Influence of Crystal Structure on Lithium-Ion Capacitor Performance.

Science.gov (United States)

Fleischmann, Simon; Zeiger, Marco; Quade, Antje; Kruth, Angela; Presser, Volker

2018-05-25

Merging of supercapacitors and batteries promises the creation of electrochemical energy storage devices that combine high specific energy, power, and cycling stability. For that purpose, lithium-ion capacitors (LICs) that store energy by lithiation reactions at the negative electrode and double-layer formation at the positive electrode are currently investigated. In this study, we explore the suitability of molybdenum oxide as a negative electrode material in LICs for the first time. Molybdenum oxide-carbon nanotube hybrid materials were synthesized via atomic layer deposition, and different crystal structures and morphologies were obtained by post-deposition annealing. These model materials are first structurally characterized and electrochemically evaluated in half-cells. Benchmarking in LIC full-cells revealed the influences of crystal structure, half-cell capacity, and rate handling on the actual device level performance metrics. The energy efficiency, specific energy, and power are mainly influenced by the overpotential and kinetics of the lithiation reaction during charging. Optimized LIC cells show a maximum specific energy of about 70 W·h·kg -1 and a high specific power of 4 kW·kg -1 at 34 W·h·kg -1 . The longevity of the LIC cells is drastically increased without significantly reducing the energy by preventing a deep cell discharge, hindering the negative electrode from crossing its anodic potential limit.

Carbon, chromium and molybdenum contents

International Nuclear Information System (INIS)

Sinatora, A; Goldenstein, H.; Mei, P.R.; Albertin, E.; Fuoco, R.; Mariotto, C.L.

1992-01-01

This work describes solidification experiments on white cast iron, with 15 and 20% of chromium, 2.3, 3.0 and 3.6 % of carbon and 0.0, 1.5 and 2.5 % of molybdenum in test de samples with 30 mm diameter. Measurements were performed on the austenite and eutectic formation arrests, the number of the eutectic carbide particles relative to the total and the eutectic volumes, and the volume fraction of the primary austenite

Kinetics of reactions of chromium, molybdenum and tungsten hexacarbonyls with hydroxylamine and trimethylamine oxide

International Nuclear Information System (INIS)

Maksakov, V.A.; Ershova, V.A.

1994-01-01

Mechanism of M(CO) 6 (M = Cr, Mo, W) reaction with hydroxylamine was studied. On the basis of kinetic data it was ascertained that as a result of the reaction CO oxidation to CO 2 and intramolecular transfer of amine formed to the central atom of metal occur. Mechanisms of M(CO) 6 reactions with hydroxylamine and trimethylamine oxide are compared

The separation of tungsten and molybdenum by the formation of sulphide complexes and extraction into a weak-base resin

International Nuclear Information System (INIS)

Fleming, C.A.

1985-01-01

The separation of molybdenum from tungten can be achieved if a solution containing molybdate and tungstate ions is reacted with sulphide ions, and the molybdenum sulphide is extracted with an anion-exchangeresin. The separation between molybdenum and tungsten is influenced byfactors such as the pH value of the solution, the concentrations of sulphide and resin in the solution, and the period of contact between theresin and the metal ions in solution. A fundamental study of the interaction between sulphide ions and molybdate or tungstate ions confirmed a mechanism proposed recently in the literature: MeOsup(2-)sub(4)+nHSsup(-)+nHsup(+) is equivalent to MeO 4 sub(-n)Ssub(n)sup(2-)+nH 2 O, where Me = molybdenum or tungsten and n = 1, 2, 3, or 4. In these reaction sequences, each successive step in the reaction (sulphur being substituted for oxygen) is slower than the preceding one, and the molybdate reactions with sulphide are several orders of magnitude faster than the analogous tungsten reactions. As a result, the extent of the complexing of tungsten with sulphide is minimal compared with that of molybdenum in the time span of the extraction experiments. However, the current investigation shows that this is not the cause of the selectivity of anion-exchange resins for molybdenum in this system, and that the separation factor between molybdenum and tungsten is much the same for the precursor tungstate anion as it is for the various tungsten sulphide anions. The selectivity of the resin for molybdenum apparently originates from a thermodynamic preference of the amine functional group on the resin for molybdenum sulphide anions over tungstate or tungsten sulphide anions. It is shown that, under optimum conditions, a separation factor of about 30 between molybdenum and tungsten can be achieved in this system

NEXAFS characterization and reactivity studies of bimetallic vanadium molybdenum oxynitride hydrotreating catalysts

Energy Technology Data Exchange (ETDEWEB)

Kapoor, R.; Oyama, S.T. [Virginia Polytechnic Inst., Blacksburg, VA (United States); Fruehberger, B.; Chen, J.G. [Exxon Research and Engineering Company, Annandale, NJ (United States)

1997-02-27

The surface and bulk compositions of vanadium molybdenum oxynitride (V{sub 2}MoO{sub 1.7}N{sub 2.4}), prepared by temperature-programmed reaction (TPR) of vanadium molybdenum oxide (V{sub 2}MoO{sub 8}) with ammonia, have been characterized using near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. The NEXAFS data were recorded at the K-edges of nitrogen and oxygen, the L-edge of vanadium, and the M-edge of molybdenum. The nitrogen K-edge region of V-Mo oxynitride shows the characteristic NEXAFS features of early-transition-metal nitrides, although these features are different from those of either VN or Mo{sub 2}N. Furthermore, comparison of the electron yield and fluorescence yield measurements also reveals that the oxidation state is different for vanadium near the surface region and for vanadium in the bulk, which is estimated to be 2.8 {+-} 0.3 and 3.8 {+-} 0.3, respectively. The oxidation state of bulk molybdenum is also estimated to be 4.4 {+-} 0.3. The X-ray diffraction pattern shows that the bulk phase of the bimetallic oxide is different from the pure monometallic oxide phases but the oxynitride has a cubic structure that resembles the pure vanadium and molybdenum nitride phases. The V-Mo oxide as prepared shows a preferential orientation of [001] crystallographic planes which is lost during the nitridation process. This shows that the solid state transformation V{sub 2}MoO{sub 8} {yields} V{sub 2}MoO{sub 1.7}N{sub 2.4} is not topotactic. 27 refs., 8 figs., 1 tab.

Nrf2 activation ameliorates cytotoxic effects of arsenic trioxide in acute promyelocytic leukemia cells through increased glutathione levels and arsenic efflux from cells

Energy Technology Data Exchange (ETDEWEB)

Nishimoto, Shoichi; Suzuki, Toshihiro; Koike, Shin [Department of Analytical Biochemistry, Meiji Pharmaceutical University, 2-522-1 Noshio, Kiyose, Tokyo 204-8588 (Japan); Yuan, Bo; Takagi, Norio [Department of Applied Biochemistry, School of Pharmacy, Tokyo University of Pharmacy and Life Sciences, Hachioji, Tokyo 192-0392 (Japan); Ogasawara, Yuki, E-mail: yo@my-pharm.ac.jp [Department of Analytical Biochemistry, Meiji Pharmaceutical University, 2-522-1 Noshio, Kiyose, Tokyo 204-8588 (Japan)

2016-08-15

Carnosic acid (CA), a phenolic diterpene isolated from Rosmarinus officinalis, has been shown to activate nuclear transcription factor E2-related factor 2 (Nrf2), which plays a central role in cytoprotective responses to oxidative and electrophilic stress. Recently, the Nrf2-Kelch ECH associating protein 1 (Keap1) pathway has been associated with cancer drug resistance attributable to modulation of the expression and activation of antioxidant and detoxification enzymes. However, the exact mechanisms by which Nrf2 activation results in chemoresistance are insufficiently understood to date. This study investigated the mechanisms by which the cytotoxic effects of arsenic trioxide (ATO), an anticancer drug, were decreased in acute promyelocytic leukemia cells treated with CA, a typical activator of Nrf2 used to stimulate the Nrf2/Keap1 system. Our findings suggest that arsenic is non-enzymatically incorporated into NB4 cells and forms complexes that are dependent on intracellular glutathione (GSH) concentrations. In addition, the arsenic complexes are recognized as substrates by multidrug resistance proteins and subsequently excreted from the cells. Therefore, Nrf2-associated activation of the GSH biosynthetic pathway, followed by increased levels of intracellular GSH, are key mechanisms underlying accelerated arsenic efflux and attenuation of the cytotoxic effects of ATO. - Highlights: • Nrf2 activation attenuates the effect of arsenic trioxide to acute promyelocytic leukemia cells. • The sensitivity of arsenic trioxide to NB4 cells was dependent on efflux rate of arsenic. • Activation of the GSH biosynthesis is essential in Nrf2-regulated responses for arsenic efflux.

Vacuum atomization of powder and shaping of net-shape components of molybdenum

International Nuclear Information System (INIS)

Devillard, Jacques.

1979-01-01

The paper reports an electron beam process and furnace for the production of spherical molybdenum powders of varying particle size prepared by vacuum atomization. Technical parameters of this process are discussed in an industrial plant. Powders of molybdenum alloys were extruded into round bars and tubes and the conditions of extrusion are specified. The mechanical properties in the as extruded state and after recrystallization were found to depend on the interstitial elements content and the particle size of the powder used. Tubes were cold bent to a 5 cm radius of curvature before or after uncanning. In the as-extruded state the tubes have a ligneous surface, the roughness depends on the particle size of the powder used. A new step of development in shaping molybdenum tubes is investigated and the cost of this process in an industrial plant is discussed [fr

Chemical and morphological characteristics of mineral trioxide aggregate and Portland cements.

Science.gov (United States)

Khan, Shahbaz; Kaleem, Muhammad; Fareed, Muhammad Amber; Habib, Amir; Iqbal, Kefi; Aslam, Ayesha; Ud Din, Shahab

2016-01-01

The purpose of this study was to investigate the chemical composition and particle morphology of white mineral trioxide aggregate (WMTA) and two white Portland cements (CEM 1 and CEM 2). Compositional analysis was performed by energy dispersive X-ray spectroscopy, X-ray fluorescence spectrometry and X-ray diffraction whereas, morphological characteristics were analyzed by scanning electron microscope and Laser scattering particle size distribution analyzer. The elemental composition of WMTA, CEM 1 and CEM 2 were similar except for the presence of higher amounts of bismuth in WMTA. Calcium oxide and silicon oxide constitute the major portion of the three materials whereas, tricalcium silicate was detected as the major mineral phase. The particle size distribution and morphology of WMTA was finer compared to CEM 1 and CEM 2. The three tested materials had relatively similar chemical composition and irregular particle morphologies.

Nanostructures obtained from a mechanically alloyed and heat treated molybdenum carbide

International Nuclear Information System (INIS)

Diaz Barriga Arceo, L.; Orozco, E.; Mendoza-Leon, H.; Palacios Gonzalez, E.; Leyte Guerrero, F.; Garibay Febles, V.

2007-01-01

Mechanical alloying was used to prepare molybdenum carbide. Microstructural characterization of samples was performed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) methods. Molybdenum carbide was heated at 800 o C for 15 min in order to produce carbon nanotubes. Nanoparticles of about 50-140 nm in diameter and nanotubes with diameters of about 70-260 nm and 0.18-0.3 μm in length were obtained after heating at 800 o C, by means of this process

Nanostructures obtained from a mechanically alloyed and heat treated molybdenum carbide

Energy Technology Data Exchange (ETDEWEB)

Diaz Barriga Arceo, L. [Programa de Ingenieria Molecular, I.M.P. Lazaro Cardenas 152, C.P. 07730 D.F. Mexico (Mexico) and ESIQIE-UPALM, IPN Apdo Postal 118-395, C.P. 07051 D.F. Mexico (Mexico)]. E-mail: luchell@yahoo.com; Orozco, E. [Instituto de Fisica UNAM, Apdo Postal 20-364, C.P. 01000 D.F. Mexico (Mexico)]. E-mail: eorozco@fisica.unam.mx; Mendoza-Leon, H. [ESIQIE-UPALM, IPN Apdo Postal 118-395, C.P. 07051 D.F. Mexico (Mexico)]. E-mail: luchell@yahoo.com; Palacios Gonzalez, E. [Programa de Ingenieria Molecular, I.M.P. Lazaro Cardenas 152, C.P. 07730 D.F. Mexico (Mexico)]. E-mail: epalacio@imp.mx; Leyte Guerrero, F. [Programa de Ingenieria Molecular, I.M.P. Lazaro Cardenas 152, C.P. 07730 D.F. Mexico (Mexico)]. E-mail: fleyte@imp.mx; Garibay Febles, V. [Programa de Ingenieria Molecular, I.M.P. Lazaro Cardenas 152, C.P. 07730 D.F. Mexico (Mexico)]. E-mail: vgaribay@imp.mx

2007-05-31

Mechanical alloying was used to prepare molybdenum carbide. Microstructural characterization of samples was performed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) methods. Molybdenum carbide was heated at 800 {sup o}C for 15 min in order to produce carbon nanotubes. Nanoparticles of about 50-140 nm in diameter and nanotubes with diameters of about 70-260 nm and 0.18-0.3 {mu}m in length were obtained after heating at 800 {sup o}C, by means of this process.

Comparative investigations of sodium arsenite, arsenic trioxide and cadmium sulphate in combination with gamma-radiation on apoptosis, micronuclei induction and DNA damage in a human lymphoblastoid cell line

International Nuclear Information System (INIS)

Hornhardt, Sabine; Gomolka, Maria; Walsh, Linda; Jung, Thomas

2006-01-01

In the field of radiation protection the combined exposure to radiation and other toxic agents is recognised as an important research area. To elucidate the basic mechanisms of simultaneous exposure, the interaction of the carcinogens and environmental toxicants cadmium and two arsenic compounds, arsenite and arsenic trioxide, in combination with gamma-radiation in human lymphoblastoid cells (TK6) were investigated. Gamma-radiation induced significant genotoxic effects such as micronuclei formation, DNA damage and apoptosis, whereas arsenic and cadmium had no significant effect on these indicators of cellular damage at non-toxic concentrations. However, in combination with gamma-radiation arsenic trioxide induced a more than additive apoptotic rate compared to the sum of the single effects. Here, the level of apoptotic cells was increased, in a dose-dependent way, up to two-fold compared to the irradiated control cells. Arsenite did not induce a significant additive effect at any of the concentrations or radiation doses tested. On the other hand, arsenic trioxide was less effective than arsenite in the induction of DNA protein cross-links. These data indicate that the two arsenic compounds interact through different pathways in the cell. Cadmium sulphate, like arsenite, had no significant effect on apoptosis in combination with gamma-radiation at low concentrations and, at high concentrations, even reduced the radiation-induced apoptosis. An additive effect on micronuclei induction was observed with 1 μM cadmium sulphate with an increase of up to 80% compared to the irradiated control cells. Toxic concentrations of cadmium and arsenic trioxide seemed to reduce micronuclei induction. The results presented here indicate that relatively low concentrations of arsenic and cadmium, close to those occurring in nature, may interfere with radiation effects. Differences in action of the two arsenic compounds were identified

Effect of molybdenum on structure, microstructure and mechanical properties of biomedical Ti-20Zr-Mo alloys

Energy Technology Data Exchange (ETDEWEB)

Kuroda, Pedro Akira Bazaglia [UNESP - Univ Estadual Paulista, Laboratório de Anelasticidade e Biomateriais, 17.033-360, Bauru, SP (Brazil); IBTN/Br – Institute of Biomaterials, Tribocorrosion and Nanomedicine, Brazilian Branch, 17.033-360 Bauru, SP (Brazil); Buzalaf, Marília Afonso Rabelo [USP – Universidade de São Paulo, Departamento de Ciências Biológicas, 17.012-901, Bauru, SP (Brazil); Grandini, Carlos Roberto, E-mail: betog@fc.unesp.br [UNESP - Univ Estadual Paulista, Laboratório de Anelasticidade e Biomateriais, 17.033-360, Bauru, SP (Brazil); IBTN/Br – Institute of Biomaterials, Tribocorrosion and Nanomedicine, Brazilian Branch, 17.033-360 Bauru, SP (Brazil)

2016-10-01

Titanium has an allotropic transformation around 883 °C. Below this temperature, the crystalline structure is hexagonal close-packed (α phase), changing to body-centered cubic (β phase). Zirconium has the same allotropic transformation around 862 °C. Molybdenum has body-centered cubic structure, being a strong β-stabilizer for the formation of titanium alloys. In this paper, the effect of substitutional molybdenum was analyzed on the structure, microstructure and selected mechanical properties of Ti-20 Zr-Mo (wt%) alloys to be used in biomedical applications. The samples were prepared by arc-melting and characterized by x-ray diffraction with subsequent refinement by the Rietveld method, optical and scanning electron microscopy. The mechanical properties were analyzed by Vickers microhardness and dynamic elasticity modulus. X-ray measurements and Rietveld analysis revealed the presence of α′ phase without molybdenum, α′ + α″ phases with 2.5 wt% of molybdenum, α″ + β phases with 5 and 7.5 wt% of molybdenum, and only β phase with 10 wt% of molybdenum. These results were corroborated by microscopy results, with a microstructure composed of grains of β phase and lamellae and needles of α′ and α″ phase in intra-grain the region. The hardness of the alloy was higher than the commercially pure titanium, due to the action of zirconium and molybdenum as hardening agents. The samples have a smaller elasticity modulus than the commercially pure titanium. - Highlights: • Ti-20Zr-Mo system alloys were developed. • β-Stabilizer effect of Zr in the presence of another β-stabilizer element • Alloys with low elastic modulus.

Transmission electron microscopy of oxide dispersion strengthened (ODS) molybdenum: effects of irradiation on material microstructure

International Nuclear Information System (INIS)

Baranwal, R.; Burke, M.G.

2003-01-01

Oxide dispersion strengthened (ODS) molybdenum has been characterized using transmission electron microscopy (TEM) to determine the effects of irradiation on material microstructure. This work describes the results-to-date from TEM characterization of unirradiated and irradiated ODS molybdenum. The general microstructure of the unirradiated material consists of fine molybdenum grains (< 5 (micro)m average grain size) with numerous low angle boundaries and isolated dislocation networks. 'Ribbon'-like lanthanum oxides are aligned along the working direction of the product form and are frequently associated with grain boundaries, serving to inhibit grain boundary and dislocation movement. In addition to the 'ribbons', discrete lanthanum oxide particles have also been detected. After irradiation, the material is characterized by the presence of nonuniformly distributed large (∼ 20 to 100 nm in diameter), multi-faceted voids, while the molybdenum grain size and oxide morphology appear to be unaffected by irradiation

Protection of MoO3 high work function by organic thin film

International Nuclear Information System (INIS)

Wang, Chenggong; Irfan, Irfan; Gao, Yongli

2014-01-01

The effects of air exposure are investigated for molybdenum trioxide (MoO 3 ) covered with organic thin films using ultraviolet photoemission spectroscopy. It is found that the severe drop of the work function of MoO 3 by air exposure is substantially reduced by the organic thin films. Both CuPc and C 60 are used for the investigations. The results indicate that the MoO 3 surface can be passivated by approximately two monolayers of organic thin films against exposure to air

Regularly arranged indium islands on glass/molybdenum substrates upon femtosecond laser and physical vapor deposition processing

Energy Technology Data Exchange (ETDEWEB)

Ringleb, F.; Eylers, K.; Teubner, Th.; Boeck, T., E-mail: torsten.boeck@ikz-berlin.de [Leibniz-Institute for Crystal Growth, Max-Born-Straße 2, Berlin 12489 (Germany); Symietz, C.; Bonse, J.; Andree, S.; Krüger, J. [Bundesanstalt für Materialforschung und-prüfung (BAM), Unter den Eichen 87, Berlin 12205 (Germany); Heidmann, B.; Schmid, M. [Department of Physics, Freie Universität Berlin, Arnimalle 14, Berlin 14195 (Germany); Nanooptical Concepts for PV, Helmholtz Zentrum Berlin, Hahn-Meitner-Platz 1, Berlin 14109 (Germany); Lux-Steiner, M. [Nanooptical Concepts for PV, Helmholtz Zentrum Berlin, Hahn-Meitner-Platz 1, Berlin 14109 (Germany); Heterogeneous Material Systems, Helmholtz Zentrum Berlin, Hahn-Meitner-Platz 1, Berlin 14109 (Germany)

2016-03-14

A bottom-up approach is presented for the production of arrays of indium islands on a molybdenum layer on glass, which can serve as micro-sized precursors for indium compounds such as copper-indium-gallium-diselenide used in photovoltaics. Femtosecond laser ablation of glass and a subsequent deposition of a molybdenum film or direct laser processing of the molybdenum film both allow the preferential nucleation and growth of indium islands at the predefined locations in a following indium-based physical vapor deposition (PVD) process. A proper choice of laser and deposition parameters ensures the controlled growth of indium islands exclusively at the laser ablated spots. Based on a statistical analysis, these results are compared to the non-structured molybdenum surface, leading to randomly grown indium islands after PVD.

Deposit of molybdenum associated with uranium in Pena Blanca, Mexico

International Nuclear Information System (INIS)

Reyes-Cortes, M.

1985-01-01

The uranium-molybdenum deposits are in the Sierra Pena Blanca, 45 km north of the city of Chihuahua. The largest amounts of uranium-molybdenum ore are found in the area of Las Margaritas-Puerto III. The ratio of molybdenum mineralization to uranium is 2:1 in this area and the deposits are distributed at depths of 55-100 m in ignimbritic rocks of the so called Escuadra Formation. This volcanic unit consists of an altered crystalline-lithic ash-flow tuff of Oligocene age. The molybdenum mineral occurs as powellite (CaMoO 4 ) and is found predominantly in two size ranges: phenocrysts 0.1-20 mm in diameter are abundant in the upper part of the deposit, while a material which varies between cryptocrystalline and amorphous predominates in the lower part. This latter material can easily be identified inside the mine by its strong orange fluorescence; it is also easy to recover by leaching. In contrast, the metallurgical process of recovery by leaching of the phenocrystalline portion of the powellite has so far presented problems. Powellite is generally found in association with carnotite, margaritasite and uranophane, and its mineralization consists of disseminated lumps, druses, crustifications and veins; frequently, it partially replaces the phenocrysts of argillized feldspars of the Escuadra Formation. Fractured and brecciated zones with intense oxidation of jarosite, haematite, limonite and goethite sometimes show high U-Mo concentrations; on other occasions the concentration is found with alunite at the contact between the ignimbrite and the layers of argillized vitrophyre. The mineralizations of fluorite, pyrite, jarosite, alunite and opal are indicative of hydrothermal deposition, possibly at low temperature with supergene or geothermal alterations. (author)

Diffusion in molybdenum disilicide

International Nuclear Information System (INIS)

Salamon, M.; Mehrer, H.

2005-01-01

The diffusion behaviour of the high-temperature material molybdenum disilicide (MoSi 2 ) was completely unknown until recently. In this paper we present studies of Mo self-diffusion and compare our present results with our already published studies of Si and Ge diffusion in MoSi 2 . Self-diffusion of molybdenum in monocrystalline MoSi 2 was studied by the radiotracer technique using the radioisotope 99 Mo. Deposition of the radiotracer and serial sectioning after the diffusion anneals to determine the concentration-depth profiles was performed using a sputtering device. Diffusion of Mo is a very slow process. In the entire temperature region investigated (1437 to 2173 K), the 99 Mo diffusivities in both principal directions of the tetragonal MoSi 2 crystals obey Arrhenius laws, where the diffusion perpendicular to the tetragonal axis is faster by two to three orders of magnitude than parallel to it. The activation enthalpies for diffusion perpendicular and parallel to the tetragonal axis are Q perpendicular to = 468 kJ mol -1 (4.85 eV) and Q parallel = 586 kJ mol -1 (6.07 eV), respectively. Diffusion of Si and its homologous element Ge is fast and is mediated by thermal vacancies of the Si sublattice of MoSi 2 . The diffusion of Mo is by several orders of magnitude slower than the diffusion of Si and Ge. This large difference suggests that Si and Mo diffusion are decoupled and that the diffusion of Mo likely takes place via vacancies on the Mo sublattice. (orig.)

Behavior of molybdenum in pyrochemical reprocessing: A spectroscopic study of the chlorination of molybdenum and its oxides in chloride melts

International Nuclear Information System (INIS)

Volkovicha, Vladimir A.; Griffiths, Trevor R.; Thied, Robert C.; Lewin, Bob

2003-01-01

The high temperature reactions of molybdenum and its oxides with chlorine and hydrogen chloride in molten alkali metal chlorides were investigated between 400 and 700 deg. C. The melts studied were LiCl-KCl, NaCl-CsCl and NaCl-KCl and the reactions were followed by in situ electronic absorption spectroscopy measurements. In these melts Mo reacts with Cl 2 and initially produces MoCl 6 2- and then a mixture of Mo(III) and Mo(V) chlorocomplexes, the final proportion depending on the reaction conditions. The Mo(V) content can be removed as MoCl 5 from the melt under vacuum or be reduced to Mo(III) by Mo metal. The reaction of Mo when HCl gas is bubbled into alkali chloride melts yields only MoCl 6 3- . MoO 2 reacts in these melts with chlorine to form soluble MoOCl 5 2- and volatile MoO 2 Cl 2 . MoO 3 is soluble in chloride melts and then decomposes into the oxychloride MoO 2 Cl 2 , which sublimes or can be sparged from the melt, and molybdate. Pyrochemical reprocessing can thus be employed for molybdenum since, after various intermediates, the end-products are chloride melts containing chloro and oxychloro anions of molybdenum plus molybdate, and volatile chlorides and oxychlorides that can be readily separated off. The reactions were fastest in the NaCl-KCl melt. The X-ray diffraction pattern of MoO 2 Cl 2 is reported for the first time

The Structure and Stability of Molybdenum Ditelluride Thin Films

Directory of Open Access Journals (Sweden)

Zhouling Wang

2014-01-01

Full Text Available Molybdenum-tellurium alloy thin films were fabricated by electron beam evaporation and the films were annealed in different conditions in N2 ambient. The hexagonal molybdenum ditelluride thin films with well crystallization annealed at 470°C or higher were obtained by solid state reactions. Thermal stability measurements indicate the formation of MoTe2 took place at about 350°C, and a subtle weight-loss was in the range between 30°C and 500°C. The evolution of the chemistry for Mo-Te thin films was performed to investigate the growth of the MoTe2 thin films free of any secondary phase. And the effect of other postdeposition treatments on the film characteristics was also investigated.

On the interaction of molybdenum cyanide complexes with hydroperoxide of tertiary butyl

International Nuclear Information System (INIS)

Vretsena, N.B.; Nikipanchuk, M.V.; Chernyak, B.I.

1979-01-01

Conducted is investigation of interaction of potassium dioxotetracyanomolybdate (4) K 4 [MoO 2 (CN) 4 ], potassium oxotetracyanomolybdate (2) K 4 [MoO(CN) 4 ] and potassium tetracyanomolybdate K 4 [Mo(CN) 4 ] in CCl 4 and hydroperoxide of tertiary butyl medium, (HPTB). Shown is the process complex mechanism which leads to molybdenum oxidation in complexes and also to coordination and HPTB decomposition. Calculated are parameters of complex formation process of molybdenum with HPTB cyanide complexes

Highlighting micrographic structures of uranium alloys containing 0.5 to 10 per cent wt molybdenum

International Nuclear Information System (INIS)

Laniesse, J.; Bouleau, M.

1959-02-01

The authors report a study which aimed at determining for different uranium molybdenum alloys and with respect to their molybdenum content a polishing method which allows a relatively simple grain examination in the as-cast condition, an as perfect as possible resolution of eutectic decompositions, and the appropriate conditions to highlight structures (beta-alpha and gamma-alpha martensite transformations, beta phase retention and decomposition, transient structures, eutectoid decomposition, and so on). Alloys differ by their molybdenum content: from 0.5 to 1 per cent wt, 1.5 to 3 per cent wt, 5 to 10 per cent wt

Preparation and characterization of dimeric and tetrameric clusters of molybdenum and tungsten

Energy Technology Data Exchange (ETDEWEB)

Ryan, T.R.

1981-10-01

The cyclo-addition of two Mo/sub 2/Cl/sub 4/(P(C/sub 6/H/sub 5/)/sub 3/)/sub 2/(CH/sub 3/OH)/sub 2/ molecules has produced a new type of tetrameric molybdenum cluster, Mo/sub 4/Cl/sub 8/L/sub 4/. Structural characterization of this dimer revealed weak molybdenum-methanol bonding which was consistent with the observed reactivity of the compound. New synthetic methods were devised for the preparation of Mo/sub 4/X/sub 8/L/sub 4/ clusters where X = Cl, Br, I and L = PR/sub 3/, Po/sub 3/, RCN, CH/sub 3/OH. A scheme for the metal-metal bonding in these clusters was presented which was in agreement with the known structural features of Mo/sub 4/Cl/sub 8/(PR/sub 3/)/sub 4/, R = C/sub 2/H/sub 5/, n-C/sub 4/H/sub 9/. The preparation of the analogous W/sub 4/Cl/sub 8/(PR/sub 3/)/sub 4/ cluster from WCl/sub 4/ was accomplished by application of techniques used in the molybdenum syntheses. The single crystal x-ray structure revealed slight differences from the molybdenum analog which were rationalized in terms of the known behavior in dimeric tungsten and molybdenum species. The attempted preparation of a tetrameric tungsten cluster from W/sub 2/(mhp)/sub 4/ was unsuccessful (mhp = anion of 2-methyl-6-hydroxypyridine). Instead, the new tungsten dimer, W/sub 2/Cl/sub 2/(mhp)/sub 3/, was isolated which possessed a metal-metal bond order of 3.5. The x-ray crystal structure of the dimer revealed that the chlorine atoms were situated cis, one bound to each tungsten. Cyclic voltammetry showed that the compound could be reversibly reduced, presumably to a W/sub 2//sup 4 +/ dimer containing a quadruple metal-metal bond.

Study of heterogeneous catalytic processes over cobalt, molybdenum and cobalt-molybdenum catalysts supported on alumina by temperature-programmed desorption and temperature-programmed reaction. 1. Adsorption of hydrozen

International Nuclear Information System (INIS)

Rozanov, V.V.; Tsao Yamin; Krylov, O.V.

1996-01-01

Hydrogen adsorption on reduced, sulphidized and reoxidized specimens of molybdenum-and cobalt-molybdenum-containing catalysts applied on aluminium oxide has been studied by the method of thermal desorption (TD). Comparison of TD spectra of hydrogen and data of X-ray phase analysis of the specimens and mass-spectrometric analysis of the products desorbed from the surface of catalysts after their successive reduction sulphidizing, carbonizing and reoxidation permitted a correlation between various forms of hydrogen adsorption and certain centres on the surface of the catalysts. 12 refs., 2 figs

Climax-Type Porphyry Molybdenum Deposits

Science.gov (United States)

Ludington, Steve; Plumlee, Geoffrey S.

2009-01-01

Climax-type porphyry molybdenum deposits, as defined here, are extremely rare; thirteen deposits are known, all in western North America and ranging in age from Late Cretaceous to mainly Tertiary. They are consistently found in a postsubduction, extensional tectonic setting and are invariably associated with A-type granites that formed after peak activity of a magmatic cycle. The deposits consist of ore shells of quartz-molybdenite stockwork veins that lie above and surrounding the apices of cupola-like, highly evolved, calc-alkaline granite and subvolcanic rhyolite-porphyry bodies. These plutons are invariably enriched in fluorine (commonly >1 percent), rubidium (commonly >500 parts per million), and niobium-tantalum (Nb commonly >50 parts per million). The deposits are relatively high grade (typically 0.1-0.3 percent Mo) and may be very large (typically 100-1,000 million tons). Molybdenum, as MoS2, is the primary commodity in all known deposits. The effect on surface-water quality owing to natural influx of water or sediment from a Climax-type mineralized area can extend many kilometers downstream from the mineralized area. Waste piles composed of quartz-silica-pyrite altered rocks will likely produce acidic drainage waters. The potential exists for concentrations of fluorine or rare metals in surface water and groundwater to exceed recommended limits for human consumption near both mined and unmined Climax-type deposits.

Development of Molybdenum Adsorbent for 99Mo/99mTc Radioisotope Generator Based on Irradiated Natural Molybdenum

International Nuclear Information System (INIS)

Rohadi Awaludin; Hotman Lubis; Sriyono; Abidin; Herlina; Endang Sarmini; Indra Saptiama; Hambali

2011-01-01

Preparation of 99 Mo/ 99m Tc radioisotope generator using irradiated natural molybdenum requires an adsorbent with high absorption capacity. Zirconium-based materials (ZBM), adsorbent with adsorption capacity of about 183 mg(Mo) / g(adsorbent), has been successfully synthesized. However, the adsorbent was easily broken in the Mo adsorption process due to many fractures in the grain. To increase the hardness, the material was immersed in tetraethyl orthosilicate (TEOS) and coated by TEOS flow in a column. The hardness test results showed that the ZBM with TEOS treatment was not broken when immersed into the Mo solution. Observations using SEM showed that the fractures formed on the ZBM were successfully removed by TEOS treatment. Measurements using EDS showed that after TEOS treatment, the silicon was detected and the oxygen content increased in the material surface. Adsorption test results showed that the TEOS immersion decreased the adsorption capacity of molybdenum from 183 to 79.8 mg of Mo per gram of adsorbent. The TEOS flow-in a column gave material with relatively high adsorption capacity, 140 mgMo per gram adsorbent. The content of Silicon in the surface was lower than that of adsorbent immersed in TEOS. (author)

One-step liquid phase chemical method to prepare carbon-based amorphous molybdenum sulfides: As the effective hydrogen evolution reaction catalysts

International Nuclear Information System (INIS)

Guo, Mengmeng; Wu, Qikang; Yu, Miaomiao; Wang, Yinling; Li, Maoguo

2017-01-01

Two different kinds of carbon-based amorphous molybdenum sulfide composite catalysts (activated carbon supported amorphous molybdenum sulfide and acetylene black supported amorphous molybdenum sulfide) had been prepared in a facile and scalable one-step liquid phase chemical method. The morphological and structural information of catalysts was characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-Ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and it’s electro-catalytic HER activity were evaluated by linear sweep voltammetry(LSV), amperometric i-t technology and AC impedance technology. The as-prepared carbon-based amorphous molybdenum sulfides showed greatly enhanced electro-catalytic activity for HER compared with pure amorphous molybdenum sulfides. Especially, the nano-sized acetylene black supported molybdenum sulfide exhibited excellent electro-catalytic HER performances with a low onset potential of −116 mV versus reverse hydrogen electrode (RHE) and a small Tafel slope of 51 mV per decade.

Density changes observed in pure molybdenum and Mo-41Re after irradiation in FFTF/MOTA

International Nuclear Information System (INIS)

Garner, F.A.; Greenwood, L.R.

1993-01-01

Pure molybdenum and Mo-41wt% Re, in both the 20% cold-worked and aged and the annealed and aged conditions, were irradiated in FFTF/MOTA to exposures as high as 111 dpa. Pure molybdenum appears to approach a saturation swelling level that is independent of the starting state. Cold-worked and aged molybdenum initially swells at a higher rate than that of solution annealed and aged molybdenum and overshoots the saturation level at lower irradiation temperatures. This requires that part of the accumulated swelling be removed to approach saturation, probably by void shrinkage. The alloy Mo-41Re exhibits a more complex behavior with the annealed and aged condition initially swelling faster, but eventually the density change of both conditions begins to turn downward and tends toward densification. The role of solid transmutation to Tc, Re, and Os is though to be very important in the irradiation behavior of these two metals. Calculations of transmutant generation are provided for FFTF, HFIR and STARFIRE spectra

Microstructure and emission ability of rare earth oxides doped molybdenum cathodes

International Nuclear Information System (INIS)

Yang Jiancan; Nie Zuoren; Wang Yiman

2003-01-01

We adopted high-resolution transmission electron microscopy (TEM) and scanning electron microscopy (SAM) to observe and analyze the microstructure of rare earth oxide (La 2 O 3 , Sc 2 O 3 ) doped molybdenum cathodes. The results show that there are many nanometer particles in the molybdenum matrix besides some sub-micrometer particles in the crystal interfaces. All these particles are rare earth oxides as determined through calculating the electron diffraction pattern. Then we determined the electron work function and the zero-field emission current of molybdenum cathodes by the electron emission measurement. To correlate the emission data with surface composition, we use Auger electron spectroscopy (AES) to analyze the elements on the activated cathode surface and their depth profiles. We found that there were about 20 nm thick layers on an activated cathode surface, which have a high content of rare earth elements. We also use AES to analyze the elements diffusion to the cathode surface from cathode body during heating up to its operating temperature to find out which element positively affects the electron emission

Boron-dependency of molybdenum boride electrocatalysts for the hydrogen evolution reaction

International Nuclear Information System (INIS)

Park, Hyounmyung; Encinas, Andrew; Fokwa, Boniface P.T.; Scheifers, Jan P.; Zhang, Yuemei

2017-01-01

Molybdenum-based materials have been considered as alternative catalysts to noble metals, such as platinum, for the hydrogen evolution reaction (HER). We have synthesized four binary bulk molybdenum borides Mo_2B, α-MoB, β-MoB, and MoB_2 by arc-melting. All four phases were tested for their electrocatalytic activity (linear sweep voltammetry) and stability (cyclic voltammetry) with respect to the HER in acidic conditions. Three of these phases were studied for their HER activity and by X-ray photoelectron spectroscopy (XPS) for the first time; MoB_2 and β-MoB show excellent activity in the same range as the recently reported α-MoB and β-Mo_2C phases, while the molybdenum richest phase Mo_2B show significantly lower HER activity, indicating a strong boron-dependency of these borides for the HER. In addition, MoB_2 and β-MoB show long-term cycle stability in acidic solution. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Boron-dependency of molybdenum boride electrocatalysts for the hydrogen evolution reaction

Energy Technology Data Exchange (ETDEWEB)

Park, Hyounmyung; Encinas, Andrew; Fokwa, Boniface P.T. [Department of Chemistry, University of California, Riverside, CA (United States); Department of Chemical and Environmental Engineering, University of California, Riverside, CA (United States); Scheifers, Jan P.; Zhang, Yuemei [Department of Chemistry, University of California, Riverside, CA (United States)

2017-05-08

Molybdenum-based materials have been considered as alternative catalysts to noble metals, such as platinum, for the hydrogen evolution reaction (HER). We have synthesized four binary bulk molybdenum borides Mo{sub 2}B, α-MoB, β-MoB, and MoB{sub 2} by arc-melting. All four phases were tested for their electrocatalytic activity (linear sweep voltammetry) and stability (cyclic voltammetry) with respect to the HER in acidic conditions. Three of these phases were studied for their HER activity and by X-ray photoelectron spectroscopy (XPS) for the first time; MoB{sub 2} and β-MoB show excellent activity in the same range as the recently reported α-MoB and β-Mo{sub 2}C phases, while the molybdenum richest phase Mo{sub 2}B show significantly lower HER activity, indicating a strong boron-dependency of these borides for the HER. In addition, MoB{sub 2} and β-MoB show long-term cycle stability in acidic solution. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Photodecomposition Profile of Curcumin in the Existence of Tungsten Trioxide Particles

Science.gov (United States)

Nandiyanto, A. B. D.; Zaen, R.; Oktiani, R.; Abdullah, A. G.

2018-02-01

The purpose of this study was to investigate the stability of curcumin solution in the existence of tungsten trioxide (WO3) particles under light illumination. In the experimental method, curcumin extracted from Indonesian local turmeric was added with WO3 microparticles and put into the photoreactor system. The photostability performance of curcumin was conducted for 22 hours using 100 W of Neon Lamp. The results showed that the curcumin solution was relatively stable. When curcumin without existence of WO3 was irradiated, no change in the curcumin concentration was found. However, when curcumin solution was mixed with WO3 particles, decreases in the concentration of curcumin was found. The concentration of curcumin with WO3 after light irradiation was about 73.58%. Based on the results, we concluded that the curcumin is relatively stable against light. However, its lightirradiation stability decreases with additional inorganic material.

Properties of low content uranium-molybdenum alloys which may be used as nuclear fuels

International Nuclear Information System (INIS)

Lehmann, J.; Decours, J.

1964-01-01

Metallurgical properties are given in this report of uranium-molybdenum alloys containing 0,5 to 3 per cent of molybdenum. Since some of these alloys are used in EDF power reactors are given: briefly the operating conditions imposed on nuclear fuels: maximum temperature, temperature gradient and external pressure. In the first part are considered the structural properties of the alloys correlation with the phase transformation kinetics; a description is given of the effects of certain physico-metallurgical factors on the morphology and the crystalline structure of the materials: - solidification conditions and the heredity of the γ structure, - cooling rate at the transformation points, - whether or not the intermediate γ → β transformation is suppressed In the second part we show how a knowledge of the phase transformation processes has made it possible to define the optimum preparation conditions for these materials in the form of fuel tubes intended for the EDF reactors: casting conditions, controlled cooling treatments, weldability. In the third part we study the thermal, stability during the long duration high temperature treatments and the cycles in the two zones of the diagram α + γ; β + γ the effects of the morphology (in particular the two types of α pseudo-grains observed) and of the cooling rate during the transformation point transitions are described. In the fourth part are discussed the mechanical properties: resistance to a tractive force, resistance to creep, resilience. These properties can also be affected by the γ structure heredity and by the cooling rate to which the alloy has been subjected. In conclusion we discuss the reasons which led to the choice of some of these alloys for the first EDF reactors in particular the advantages of their high creep resistance between 450 and 600 deg C for use in the form of tubes subjected to an external pressure. (authors) [fr

Molybdenum-UO2 cerment irradiation at 1145 K

Science.gov (United States)

Mcdonald, G.

1971-01-01

Two molybdenum-UO2 cermet fuel pins were fission heated in a helium-cooled loop at a temperature of 1145 K and to a total burnup of 5.3 % of the U-235. After irradiation the fuel pins were measured to check dimensional stability, punctured at the plenums to determine fission gas release, and examined metallographically to determine the effect of irradiation. Burnup was determined in several sections of the fuel pin. The results of the postirradiation examination indicated: (1) There was no visible change in the fuel pins on irradiation under the above conditions. (2) The maximum swelling of the fuel pins was less than 1%. (3) There was no migration of UO2 and no visible interaction between the molybdenum and the UO2. (4) Approximately 12% of the fission gas formed was released from the cermet cone into the gas plenum.

Use of arsenic trioxide in remission induction and consolidation therapy for acute promyelocytic leukaemia in the Australasian Leukaemia and Lymphoma Group (ALLG) APML4 study: a non-randomised phase 2 trial.

Science.gov (United States)

Iland, Harry J; Collins, Marnie; Bradstock, Ken; Supple, Shane G; Catalano, Alberto; Hertzberg, Mark; Browett, Peter; Grigg, Andrew; Firkin, Frank; Campbell, Lynda J; Hugman, Amanda; Reynolds, John; Di Iulio, Juliana; Tiley, Campbell; Taylor, Kerry; Filshie, Robin; Seldon, Michael; Taper, John; Szer, Jeff; Moore, John; Bashford, John; Seymour, John F

2015-09-01

Initial treatment of acute promyelocytic leukaemia traditionally involves tretinoin (all-trans retinoic acid) combined with anthracycline-based risk-adapted chemotherapy, with arsenic trioxide being the treatment of choice at relapse. To try to reduce the relapse rate, we combined arsenic trioxide with tretinoin and idarubicin in induction therapy, and used arsenic trioxide with tretinoin as consolidation therapy. Patients with previously untreated genetically confirmed acute promyelocytic leukaemia were eligible for this study. Eligibilty also required Eastern Cooperative Oncology Group performance status 0-3, age older than 1 year, normal left ventricular ejection fraction, Q-Tc interval less than 500 ms, absence of serious comorbidity, and written informed consent. Patients with genetic variants of acute promyelocytic leukaemia (fusion of genes other than PML with RARA) were ineligible. Induction comprised 45 mg/m(2) oral tretinoin in four divided doses daily on days 1-36, 6-12 mg/m(2) intravenous idarubicin on days 2, 4, 6, and 8, adjusted for age, and 0·15 mg/kg intravenous arsenic trioxide once daily on days 9-36. Supportive therapy included blood products for protocol-specified haemostatic targets, and 1 mg/kg prednisone daily as prophylaxis against differentiation syndrome. Two consolidation cycles with tretinoin and arsenic trioxide were followed by maintenance therapy with oral tretinoin, 6-mercaptopurine, and methotrexate for 2 years. The primary endpoints of the study were freedom from relapse and early death (within 36 days of treatment start) and we assessed improvement compared with the 2 year interim results. To assess durability of remission we compared the primary endpoints and disease-free and overall survival at 5 years in APML4 with the 2 year interim APML4 data and the APML3 treatment protocol that excluded arsenic trioxide. This study is registered with the Australian New Zealand Clinical Trials Registry, number ACTRN12605000070639. 124

Neutron activation determination of impurities in molybdenum

International Nuclear Information System (INIS)

Usmanova, M.M.; Mukhamedshina, N.M.; Obraztsova, T.V.; Saidakhmedov, K.Kh.

1984-01-01

Instrumental neutron-activation techniques of impurity element determination in molybdenum and MoO 3 (solid and powdered samples) have been developed. When determining impurities of Na, K, Mn, Cu, W, Re molybdenum has been irradiated by thermal neutrons in reactor for 20 min, the sample mass constituted 200-300 mg, sample cooling time after irradiation - 2.5-3.5 h. It is shown that in the process of Cr, Fe, Co, Zn determination the samples should be irradiated with thermal neutrons, and in the process of Sb, Ta and Ni determination - with resonance and fast neutrons. Simultaneous determination of the elements during irradiation with neutrons with reactor spectrum is possible. When determining P and S the samples are irradiated with thermal and epithermal neutrons and β-activity of samples and comparison samples are measured using β-spectrometer with anthracene crystal. The techniques developed permit to determine impurities in Mo with a relative standard deviation 0.07-0.15 and lower boundaries of contents determined - 10 -4 - 10 -7 %

Stress analysis of glass-ceramic insulator and molybdenum cylinders in vacuum tube subassembly

International Nuclear Information System (INIS)

Spears, R.K.

1980-01-01

This study determined the state of stress between molybdenum cylinders and a glass-ceramic insulator of a vacuum tube during cooling when the glass-ceramic coefficient of expansion differed from molybdenum by +-2 x 10 -7 / 0 C. A thermoelastic stress analysis was performed on the vacuum tube subassembly using the finite element method. Two cases, which examined the effect of cooling over a 700 0 C range, were considered. In Case One, the expansion coefficient of the glass-ceramic was 2 x 10 -7 / 0 C less than that of molybdenum while for Case Two, it was 2 x 10 -7 / 0 C greater. For Case One, it was found that the tangential stresses in the insulator were entirely compressive but the maximum principal stresses in the r-z plane were mainly tensile. For Case Two, the tangential stresses were tensile in the insulator as were most of the maximum principal stresses in the r-z plane except for stress in the upper regions of the insulator. The magnitude of the stress at the maximum principal stress location appears to be substantially lower than what has been observed in practice (i.e., cracking of this design had never been a major problem, but it has been observed that if the coefficient of expansion of the glass-ceramic was 2 x 10 -7 / 0 C lower than molybdenum, cracking usually resulted). This analysis showed that the expansion coefficient of the glass-ceramic could be varied quite liberally from molybdenum before the ultimate strength (13,000 lb/in. 2 ) of the glass-ceramic was exceeded

The Technological Mineralogical Research of Molybdenum in Skarn-type Ore of Huangshaping Polymetallic Mining Area, Hunan, China

Science.gov (United States)

Liu, W. H.; Pan, J. Y.

2017-10-01

Huangshaping is one of the most important polymetallic deposits in the south of Hunan Province. Through field investigation, chemical analysis, observation under the optical microscope, energy spectrum analysis of the SEM and X-ray diffraction, the author made a technological mineralogical research of molybdenum on skarn-type ore, and the result shows that the ore containing molybdenum is mainly on the contact of the granite porphyry and the impure limestone in the lower carboniferous Shidengzi group. Besides molybdenum, the ore minerals contain scheelite, native bismuth, bismuthinite, magnetite and so on; and the gangue minerals are mainly andradite, fluorite and wollastonite. Part of the molybdenum exists in the scheelite in form of isomorphism, and there is an obvious negative correlation between MoO3 and WO3. The molybdenite granularity is mainly located in the 0.04~ 0.08mm area, which accounts for 29.5% of the total and is the finely disseminated ore. For samples of 70%, 90%, and 100% with the particle size of more than 200 meshes, the maximum recovery of the molybdenite are 75.15%, 86.45% and 91.25% respectively. So there will be a better use of molybdenum if we properly improve the grinded particle size of the comprehensive samples. As part of the molybdenum is distributed in the scheelite lattice, the actual recovery rate in this area may decline compared with the ideal value.

Spectrophotometric determination of molybdenum with non-ionic surfactant and thiocyanate

International Nuclear Information System (INIS)

Hayashi, Kenjiro; Yamamoto, Atsuo; Fujimura, Yasue; Ito, Saburo.

1980-01-01

Although the molybdenum (V)-thiocyanate complex is quite stable in non-aqueous solvent such as ether, the complex in dilute acidic solution is unstable. However, this unstable complex was stabilized remarkably by addition of some non-ionic surfactant such as Triton X-100 (alkylphenolpolyoxyethylene ether). The application of this stabilizing effect of the surfactant to the photometric determination of trace amounts of molybdenum with thiocyanate resulted in an increase in the sensitivity. The rate of formation of the Mo(V)-SCN complex was affected by the presence of ferrous ion and its rate constant was proportional to the concentration of Fe(II). The stabilizing effect of the surfactant on the yellowish orange coloration can be understood if we assume that the Mo(V)-SCN complex is incorporated into the micelles of Triton X-100 as [H 2 + , MoO(CNS) 5 2- ]. The optimum condition for the determination of molybdenum is as follows: concentration of sulfuric acid, 0.22 mol dm -3 ; Triton X-100, 0.8%; ascorbic acid, 0.32 mol dm -3 ; thiocyanate, 0.30 mol dm -3 ; iron, 40 mg dm -3 ; standing time for coloration, 10 min and more. Beer's law was obeyed over the range (1 -- 233) μg/50 cm 3 . The molar absorption coefficient at 468 nm was 1.7 2 x 10 4 cm -1 mol -1 dm 3 . The maximum permissible limits of foreign ions (mg/50 cm 3 ) were as follows: Ni(30); Co(12); W(VI) (2); Cu, Zn, V(V) (3); Cr(VI) (5). Large amounts of iron interfered, but this interference was removed by addition of the same amount of iron to the reagent blank. Trace amounts of molybdenum in steel was determined by this method with satisfactory results. (author)

On the mechanism of dispersion hardening in molybdenum-carbide alloy systems

International Nuclear Information System (INIS)

Shulepov, V.I.; Yudkovskij, S.I.; Batenina, O.I. et al.

1975-01-01

The effect of heat treatment of the forming alloys of the Mo-Ti-C and Mo-Ti-Zr-C systems (at the temperatures below the recrystallization temperature) on the structure, distribution of carbon and mechanical properties of the alloys is studied. It is shown that the dispersion-strengthened state of the molybdenum alloys may be obtained on the account of the deformation ageing effect, rather than through the use of the standard heat-treatment procedure (hardening plus ageing). On the basis of the experimental results a theoretical explanation of strengthening of the high-alloy molybdenum-titanum-carbon system is given

Retinoic acid and arsenic trioxide in the treatment of acute promyelocytic leukemia: current perspectives

Directory of Open Access Journals (Sweden)

McCulloch D

2017-03-01

Full Text Available Derek McCulloch, Christina Brown, Harry Iland Institute of Hematology, Royal Prince Alfred Hospital, Camperdown, NSW, Australia Abstract: Acute promyelocytic leukemia (APL is a distinct subtype of acute myeloid leukemia (AML with a unique morphological appearance, associated coagulopathy and canonical balanced translocation of genetic material between chromosomes 15 and 17. APL was first described as a distinct subtype of AML in 1957 by Dr Leif Hillestad who recognized the pattern of an acute leukemia associated with fibrinolysis, hypofibrinogenemia and catastrophic hemorrhage. In the intervening years, the characteristic morphology of APL has been described fully with both classical hypergranular and variant microgranular forms. Both are characterized by a balanced translocation between the long arms of chromosomes 15 and 17, [t(15;17(q24;q21], giving rise to a unique fusion gene PML-RARA and an abnormal chimeric transcription factor (PML-RARA, which disrupts normal myeloid differentiation programs. The success of current treatments for APL is in marked contrast to the vast majority of patients with non-promyelocytic AML. The overall prognosis in non-promyelocytic AML is poor, and although there has been an improvement in overall survival in patients aged <60 years, only 30%–40% of younger patients are still alive 5 years after diagnosis. APL therapy has diverged from standard AML therapy through the empirical discovery of two agents that directly target the molecular basis of the disease. The evolution of treatment over the last 4 decades to include all-trans retinoic acid and arsenic trioxide, with chemotherapy limited to patients with high-risk disease, has led to complete remission in 90%–100% of patients in trials and rates of overall survival between 86% and 97%. Keywords: acute promyelocytic leukemia, ATRA, arsenic trioxide

Surface analyses of TiC coated molybdenum limiter material exposed to high heat flux electron beam

International Nuclear Information System (INIS)

Onozuka, M.; Uchikawa, T.; Yamao, H.; Kawai, H.; Kousaku, A.; Nakamura, H.; Niikura, S.

1986-01-01

Observation and surface analyses of TiC coated molybdenum exposed to high heat flux have been performed to study thermal damage resistance of TiC coated molybdenum limiter material. High heat loads were provided by a 120 kW electron beam facility. (author)

Well-Defined Silica Grafted Molybdenum Bis(imido) Catalysts for Imine Metathesis Reactions

KAUST Repository

Barman, Samir

2017-04-06

Novel site-isolated tetracoordinated molybdenum complexes possessing bis(imido) ligands, [(≡Si–O)2Mo(═NR)2] (R = t-Bu, 2,6-C6H3-i-Pr2), were immobilized on partially dehydroxylated silica (SiO2-200) by a rigorous surface organometallic chemistry protocol. The newly developed materials adorned with bis(imido) functional units, which were previously exploited mainly as spectator ligands on silica-supported olefin metathesis molybdenum catalysts, are found to be efficient heterogeneous catalytic systems for imine cross metathesis under mild conditions.

Well-Defined Silica Grafted Molybdenum Bis(imido) Catalysts for Imine Metathesis Reactions

KAUST Repository

Barman, Samir; Merle, Nicolas; Minenkov, Yury; De Mallmann, Aimery; Samantaray, Manoja; Le Qué mé ner, Fré dé ric; Szeto, Kai C.; Abou-Hamad, Edy; Cavallo, Luigi; Taoufik, Mostafa; Basset, Jean-Marie

2017-01-01

Novel site-isolated tetracoordinated molybdenum complexes possessing bis(imido) ligands, [(≡Si–O)2Mo(═NR)2] (R = t-Bu, 2,6-C6H3-i-Pr2), were immobilized on partially dehydroxylated silica (SiO2-200) by a rigorous surface organometallic chemistry protocol. The newly developed materials adorned with bis(imido) functional units, which were previously exploited mainly as spectator ligands on silica-supported olefin metathesis molybdenum catalysts, are found to be efficient heterogeneous catalytic systems for imine cross metathesis under mild conditions.

Reaction of boron carbide with molybdenum disilicide

International Nuclear Information System (INIS)

Novikov, A.V.; Melekhin, V.F.; Pegov, V.S.

1989-01-01

The investigation results of interaction in the B 4 C-MoSi 2 system during sintering in vacuum are presented. Sintering of boron carbide with molybdenum disilicide is shown to lead to the formation of MoB 2 , SiC, Mo 5 Si 3 compounds, the presence of carbon-containing covering plays an important role in sintering

Extraction and selective stripping of uranium and molybdenum in sulfate solution using amines

International Nuclear Information System (INIS)

Sialino, E.; Mignot, C.; Michel, P.; Vial, J.

1977-01-01

The uranium solutions issued from leaching of AKOUTA ores and containing lot of molybdenum are purified using solvent extraction. During the first test run precipitation of complexes such as amine phosphomolybdate was observed. It was pointed out that the precipitation could be prevented if the molybdenum is oxidized in the feed prior to solvent extraction. Informations on the basic studies carried out to ensure the reliability of the process are given in the complete paper

Uranium refining in South Africa. The production of uranium trioxide, considering raw material properties and nuclear purity requirements

International Nuclear Information System (INIS)

Colborn, R.P.; Bayne, D.L.G.; Slabber, M.N.

1980-01-01

Conventional practice results in raw materials being delivered to the uranium refineries in a form more suitable for transportation than for processing, and therefore the refineries are required to treat these raw materials to produce an acceptable intermediate feed stock. During this treatment, it is advantageous to include a purification step to ensure that the feed stock is of the required purity for nuclear grade uranium hexafluoride production, and this usually results in ammonium diuranate slurries of the required quality being produced as the intermediate feed stock. All subsequent processing steps can therefore be standardized and are effectively independent of the origin of the raw materials. It is established practice in South Africa to transport uranium as an ammonium diuranate slurry from the various mines to the Nufcor central processing plant for UOC production, and therefore the process for the production of uranium hexafluoride in South Africa was designed to take cognizance of existing transport techniques and to accept ammonium diuranate slurries as the raw material. The South African refinery will be able to process these slurries directly to uranium trioxide. This paper discusses the conditions under which the various ammonium diuranate raw materials, exhibiting a wide range of properties, can be effectively processed to produce a uranium trioxide of acceptably consistent properties. Mention is also made of the uranium hexafluoride distillation process adopted

Integral experiment on molybdenum with DT neutrons at JAEA/FNS

Energy Technology Data Exchange (ETDEWEB)

Ohta, Masayuki, E-mail: ohta.masayuki@jaea.go.jp; Sato, Satoshi; Kwon, Saerom; Ochiai, Kentaro; Konno, Chikara

2016-11-01

Highlights: • An integral experiment on molybdenum was conducted with DT neutron at JAEA/FNS. • The experimental results were analyzed by MCNP5 with recent nuclear data libraries. • The calculated results generally show underestimation. • Problems on recent nuclear data of molybdenum were discussed. - Abstract: An integral experiment on molybdenum is performed with a DT neutron source at JAEA/FNS. A Mo assembly is covered with lithium oxide blocks in order to reduce background neutrons inside the assembly. Several reaction rates and fission rates are measured along the central axis inside the assembly and compared with calculated ones with the Monte Carlo transport code MCNP5-1.40 and recent nuclear data libraries of ENDF/B-VII.1, JENDL-4.0, and JEFF-3.2. The calculated results generally show underestimation. From our detailed analysis, it is concluded that the (n,2n) cross section data of all the Mo stable isotopes in JEFF-3.2 are more suitable than those in JENDL-4.0 and the (n,γ) cross section data of {sup 92}Mo, {sup 94}Mo, {sup 95}Mo, {sup 96}Mo, {sup 97}Mo, and {sup 100}Mo in JENDL-4.0 are overestimated.

High heat flux testing of TiC coated molybdenum with a tungsten intermediate layer

International Nuclear Information System (INIS)

Fujitsuka, Masakazu; Fukutomi, Masao; Okada, Masatoshi

1988-01-01

The use of low atomic number (Z) material coatings for fusion reactor first-wall components has proved to be a valuable technique to reduce the plasma radiation losses. Molybdenum coated with titanium carbide is considered very promising since it has a good capability of receiving heat from the plasma. An interfacial reaction between the TiC film and the molybdenum substrate, however, causes a severe deterioration of the film at elevated temperatures. In order to solve this problem a TiC coated molybdenum with an intermediate tungsten layer was developed. High temperature properties of this material was evaluated by a newly devised electron beam heating apparatus. TiC coatings prepared on a vacuum-heat-treated molybdenum with a tungsten intermediate layer showed good high temperature stability and survived 2.0 s pulses of heating at a power density as high as 53 MW/m 2 . The melt area of the TiC coatings in high heat flux testings also markedly decreased when a tungsten intermediate layer was applied. The melting mechanism of the TiC coatings with and without a tungsten intermediate layer was discussed by EPMA measurements. (author)

Physical chemical quality control of the molybdenum technetium generator

International Nuclear Information System (INIS)

Olive, E.; Cruz, J.; Isaac, M.; Gamboa, R.; D'Alessandro, K.; Desdin, L.F.

1995-01-01

Comparative operational procedure imported molybdenum technetium generators have been made. Procedures for determination of chemical, radiochemical and radionuclidic purities that may be applied in Hospital's laboratories and in the quality control of generators production are developed

Characterisation of the simultaneous molybdenum reduction and glyphosate degradation by Burkholderia vietnamiensis AQ5-12 and Burkholderia sp. AQ5-13.

Science.gov (United States)

Manogaran, Motharasan; Ahmad, Siti Aqlima; Yasid, Nur Adeela; Yakasai, Hafeez Muhammad; Shukor, Mohd Yunus

2018-02-01

In this novel study, we report on the use of two molybdenum-reducing bacteria with the ability to utilise the herbicide glyphosate as the phosphorus source. The bacteria reduced sodium molybdate to molybdenum blue (Mo-blue), a colloidal and insoluble product, which is less toxic. The characterisation of the molybdenum-reducing bacteria was carried out using resting cells immersed in low-phosphate molybdenum media. Two glyphosate-degrading bacteria, namely Burkholderia vietnamiensis AQ5-12 and Burkholderia sp. AQ5-13, were able to use glyphosate as a phosphorous source to support molybdenum reduction to Mo-blue. The bacteria optimally reduced molybdenum between the pHs of 6.25 and 8. The optimum concentrations of molybdate for strain Burkholderia vietnamiensis strain AQ5-12 was observed to be between 40 and 60 mM, while for Burkholderia sp. AQ5-13, the optimum molybdate concentration occurred between 40 and 50 mM. Furthermore, 5 mM of phosphate was seen as the optimum concentration supporting molybdenum reduction for both bacteria. The optimum temperature aiding Mo-blue formation ranged from 30 to 40 °C for Burkholderia vietnamiensis strain AQ5-12, whereas for Burkholderia sp. AQ5-13, the range was from 35 to 40 °C. Glucose was the best electron donor for supporting molybdate reduction, followed by sucrose, fructose and galactose for both strains. Ammonium sulphate was the best nitrogen source in supporting molybdenum reduction. Interestingly, increasing the glyphosate concentrations beyond 100 and 300 ppm for Burkholderia vietnamiensis strain AQ5-12 and Burkholderia sp. AQ5-13, respectively, significantly inhibited molybdenum reduction. The ability of these bacteria to reduce molybdenum while degrading glyphosate is a useful process for the bioremediation of both toxicants.

Development of a potentiometric EDTA method for determination of molybdenum. Use of the analysis for molybdenite concentrates

Science.gov (United States)

Khristova, R.; Vanmen, M.

1986-01-01

Based on considerations of principles and experimental data, the interference of sulfate ions in poteniometric titration of EDTA with FeCl3 was confirmed. The method of back complexometric titration of molybdenum of Nonova and Gasheva was improved by replacing hydrazine sulfate with hydrazine hydrochloride for reduction of Mo(VI) to Mo(V). The method can be used for one to tenths of mg of molybdenum with 0.04 mg standard deviation. The specific method of determination of molybdenum in molybdenite concentrates is presented.

Development of a potentiometric EDTA method for determination of molybdenum. Use of the analysis for molybdenite concentrates

International Nuclear Information System (INIS)

Khristova, R.; Vanmen, M.

1976-01-01

Based on considerations of principles and experimental data, the interference of sulfate ions in poteniometric titration of EDTA with FeCl 3 was confirmed. The method of back complexometric titration of molybdenum of Nonova and Gasheva was improved by replacing hydrazine sulfate with hydrazine hydrochloride for reduction of Mo(VI) to Mo(V). The method can be used for one to tenths of mg of molybdenum with 0.04 mg standard deviation. The specific method of determination of molybdenum in molybdenite concentrates is presented

XPS and electrochemical studies of the dissolution and passivation of molybdenum-implanted austenitic stainless steels

International Nuclear Information System (INIS)

De Vito, E.; Marcus, P.

1993-01-01

X-ray Photoelectron Spectroscopy (XPS) was used to investigate the chemical composition and the chemical states of the passive film formed on austenitic stainless steels (Fe-19Cr-10Ni (at.%)) which have been implanted with molybdenum (Mo + , 100 keV, 2.5 x 10 16 at./cm 2 ). Prior to passivation the implanted alloy was characterized by RBS (Rutherford Backscattering Spectroscopy) and XPS. Alloys with well-defined surface concentrations of molybdenum were prepared by ion sputtering the implanted alloy in the preparation chamber of the spectrometer, to a fixed point in the implantation profile. The samples were then transferred without air exposure to a glove box with inert gas in which the electrochemical measurements were performed. After passivation, return transfer of the passivated samples was done with the same transfer device to avoid exposure to air. In 0.5 M H 2 SO 4 , the anodic dissolution current density decreases with increasing Mo content on the alloy surface. Surface analysis by XPS showed that the surface is enriched with molybdenum in the Mo 4+ chemical state. The current density in the passive state is similar for both the non-implanted and the implanted alloys. Surface analysis by XPS showed that the passive film has a bilayer structure (inner oxide and outer hydroxide) and that the hydroxide layer present on the surface of the passive film is markedly enriched with molybdenum in the Mo 6+ chemical state. The XPS measurements indicate that the presence of molybdenum favors the formation of chromium hydroxide at the expense of chromium oxide. A significant enrichment of the alloyed (Cr, Ni) and implanted (Mo) elements was also observed in the metallic phase under the passive film. The possible mechanisms of the effect of molybdenum on the corrosion resistance of stainless steels are discussed in light of the obtained surface analytical results

A ductile fracture criterion with Zener-Hollomon parameter of pure molybdenum sheet in thermal forming

Directory of Open Access Journals (Sweden)

Wang Chu

2015-01-01

Full Text Available Formability of pure molybdenum in thermal forming process has been greatly improved, but it is still hard to avoid the generation of rupture and other quality defects. In this paper, a ductile fracture criterion of pure molybdenum sheet in thermal forming was established by considering the plastic deformation capacity of material and stress states, which can be used to describe fracture behaviour and critical rupture prediction of pure molybdenum sheet during hot forming process. Based on the isothermal uniaxial tensile tests which performed at 993 to 1143 K with strain rate range from 0.0005 to 0.2 s−1, the material parameters are calculated by the combination method of experiment with FEsimulation. Based on the observation, new fracture criteria can be expressed as a function of Zener-Hollomon parameter. The critical fracture value that calculated by Oyane-Sato criterion increases with increasing temperature and decreasing strain rate. The ductile fracture criterion with Zener-Hollomon parameter of pure molybdenum in thermal forming is proposed.

A case of accidental intake of Molybdenum Radionuclides: analysis of data with a revised biokinetic model

International Nuclear Information System (INIS)

Giussani, A.; Cantone, M.C.; Tavola, F.; Lopez, M.A.; Navarro, T.

2002-01-01

In recent years, a series of investigations on the biokinetics of molybdenum in humans, conducted using stable isotopes of Mo as tracers, has provided valuable experimental data about the dynamics of relevant processes such as the uptake from the gut walls, the clearance from the systemic circulation and the elimination pathways. The results of these studies are in good agreement with the findings of a group of nutritionist who also performed biokinetic studies with stable tracers. All measurements show several deviations from the predictions of the current ICRP model. On the basis of these data, a preliminary revision of the biokinetic model for Mo was presented. The modified model was thus used as a starting point for a new series of biokinetic investigations, aimed at a better definition of some of its features. In a total of 54 studies conducted in 15 volunteers, the influence of the mass and of the chemical form on intestinal absorption, internal kinetics and urinary excretion was investigated

Structure and reactivity of molybdenum oxide cluster ions in the gas phase

International Nuclear Information System (INIS)

Goncharov, V.B.; Fialko, E.F.

2002-01-01

A set of cluster ions of molybdenum oxides Mo x O y + (x = 1-5, y = 1-15) was prepared using a combination of the ionic cyclotron resonance method and Knudsen effusion source. Dependence of concentration of different molybdenum oxide ions on the time of retention and their interaction with carbon monoxide was studied. It is shown that Mo x O y + ions with x>3 contain cyclic fragment Mo 3 O 9 in their structure. Oxygen binding energies within ionic clusters Mo x O y + were estimated [ru

Statistics of grain misorientations in molybdenum

Energy Technology Data Exchange (ETDEWEB)

Rybin, V V; Titovets, Yu F; Teplitskij, D M; Zolotorevskij, N Yu

1982-03-01

Sets of misorientations between neighbouring grains for three recrystallized molybdenum polycrystals differing in purity, phase composition and prehistory are experimentally determined. The data obtained are analyzed according to modern representations of intergrain boundary structure. In the two materials among the three mentioned above the share of boundaries close to special boundaries with high density of coinciding points turned to be 1.5 times higher than in the polycrystal with chaotic distribution of grains by orientations.

Establishment and characterization of arsenic trioxide resistant KB/ATO cells.

Science.gov (United States)

Zhang, Yun-Kai; Dai, Chunling; Yuan, Chun-Gang; Wu, Hsiang-Chun; Xiao, Zhijie; Lei, Zi-Ning; Yang, Dong-Hua; Le, X Chris; Fu, Liwu; Chen, Zhe-Sheng

2017-09-01

Arsenic trioxide (ATO) is used as a chemotherapeutic agent for the treatment of acute promyelocytic leukemia. However, increasing drug resistance is reducing its efficacy. Therefore, a better understanding of ATO resistance mechanism is required. In this study, we established an ATO-resistant human epidermoid carcinoma cell line, KB/ATO, from its parental KB-3-1 cells. In addition to ATO, KB/ATO cells also exhibited cross-resistance to other anticancer drugs such as cisplatin, antimony potassium tartrate, and 6-mercaptopurine. The arsenic accumulation in KB/ATO cells was significantly lower than that in KB-3-1 cells. Further analysis indicated that neither application of P-glycoprotein inhibitor, breast cancer resistant protein (BCRP) inhibitor, or multidrug resistance protein 1 (MRP1) inhibitor could eliminate ATO resistance. We found that the expression level of ABCB6 was increased in KB/ATO cells. In conclusion, ABCB6 could be an important factor for ATO resistance in KB/ATO cells. The ABCB6 level may serve as a predictive biomarker for the effectiveness of ATO therapy.

Development of Chemosorbent Based on Metallic Waste for Cleaning Mine Water From Molybdenum

Directory of Open Access Journals (Sweden)

Alexander Evgenyevich Isakov

2018-01-01

Full Text Available The article presents the results of hydrochemical studies of water objects, located in the impact zone of one of the largest mining enterprises in the Russian Federation – JSC “Apatite”. According to the monitoring studies, the source of surface water pollution with molybdenum was determined, geochemical assessment of the molybdenum transformation in the system “ore-bearing rocks – mine water – surface water” was performed. In order to reduce the technogenic load on the surface water located in the considered area, the way of large-tonnage mine waters purificationfrom molybdenum was proposed. The method involves using the chemical sorbent based on waste metals. The method of sewage purificationwill allow solving one of the key environmental problems of the considered enterprise and, in addition, to improve the environmental situation in the considered area as well as the quality of the local population life.

Molybdenum oxide nanocolloids prepared by an external field-assisted laser ablation in water

Directory of Open Access Journals (Sweden)

Spadaro Salvatore

2018-01-01

Full Text Available he synthesis of extremely stable molybdenum oxide nanocolloids by pulsed laser ablation was studied. This green technique ensures the formation of contaminant-free nanostructures and the absence of by-products. A focused picosecond pulsed laser beam was used to ablate a solid molybdenum target immersed in deionized water. Molybdenum oxide nearly spherical nanoparticles with dimensions within few nanometers (20-100 nm are synthesized when the ablation processes were carried out, in water, at room temperature and 80°C. The application of an external electric field during the ablation process induces a nanostructures reorganization, as indicated by Scanning-Transmission Electron Microscopy images analysis. The ablation products were also characterized by some spectroscopic techniques: conventional UV-vis optical absorption, atomic absorption, dynamic light scattering, micro-Raman and X-ray photoelectron spectroscopies. Finally, NIH/3T3 mouse fibroblasts were used to evaluate cell viability by the sulforhodamine B assay

Impact of helium implantation and ion-induced damage on reflectivity of molybdenum mirrors

Energy Technology Data Exchange (ETDEWEB)

Garcia-Carrasco, A., E-mail: alvarogc@kth.se [Department of Fusion Plasma Physics, Royal Institute of Technology (KTH), Teknikringen 31, 100 44 Stockholm (Sweden); Petersson, P.; Hallén, A. [Department of Fusion Plasma Physics, Royal Institute of Technology (KTH), Teknikringen 31, 100 44 Stockholm (Sweden); Grzonka, J. [Faculty of Materials Science and Engineering, Warsaw University of Technology, 02-507 Warsaw (Poland); Institute of Electronic Materials Technology, 133 Wolczynska Str., 01-919 Warsaw (Poland); Gilbert, M.R. [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Fortuna-Zalesna, E. [Faculty of Materials Science and Engineering, Warsaw University of Technology, 02-507 Warsaw (Poland); Rubel, M. [Department of Fusion Plasma Physics, Royal Institute of Technology (KTH), Teknikringen 31, 100 44 Stockholm (Sweden)

2016-09-01

Molybdenum mirrors were irradiated with Mo and He ions to simulate the effect of neutron irradiation on diagnostic first mirrors in next-generation fusion devices. Up to 30 dpa were produced under molybdenum irradiation leading to a slight decrease of reflectivity in the near infrared range. After 3 × 10{sup 17} cm{sup −2} of helium irradiation, reflectivity decreased by up to 20%. Combined irradiation by helium and molybdenum led to similar effects on reflectivity as irradiation with helium alone. Ion beam analysis showed that only 7% of the implanted helium was retained in the first 40 nm layer of the mirror. The structure of the near-surface layer after irradiation was studied with scanning transmission electron microscopy and the extent and size distribution of helium bubbles was documented. The consequences of ion-induced damage on the performance of diagnostic components are discussed.

Synthesis and superconductivity of molybdenum cluster compounds (Chevrel phase)

International Nuclear Information System (INIS)

Culetto, F.J.

1979-05-01

The discovery of superconductivity in ternary molybdenum sulfides (Chevrel phases) in 1972 has stimulated research on these compounds. Some of the phases show extremely high critical fields Hc 2 and might therefore find technical application as high field superconductors. In order to understand the electron-phonon-interaction in these substances, measurements of the superconducting isotope effect in 92-100 Mo 6 Se 8 , Mo 6 76-82 Se 8 , and 116-124 SnMo 6 S 8 have been performed. The corresponding isotope effect exponents β (βmo=0.27 +- 0.04, βSe=0.27 +- 0.05 and βSn 6 Se 8 . In case of the ternary Chevrel phase SnMo 6 S 8 , phonon modes connected with displacements of the Sn-ions have only minor influence on the transition temperature. This result can be explained by the weak overlap of the molybdenum dsub(x)2sub(-y)2 - orbitals with Sn-sites. Furthermore, we report experiments on the synthesis of new Chevrel phase materials. In order to optimize the valence electron concentration in some ternary molybdenum selenide compounds, chalcogen exchange reactions have been performed. A new Chevrel phase superconductor, Cusub(x)Mo 6 S 6 J 2 with x=0 - 1.2, has been synthesized by copper diffusion into the non occupied channels running between the Mo 6 S 6 J 2 -'molecules' of Mo 6 S 6 J 2 . (orig.)

Materials for Molybdenum 99 purification

International Nuclear Information System (INIS)

Wilkinson, M. Victoria; Mondino, Angel V.; Manzini, Alberto C.

2003-01-01

The National Atomic Energy Commission (CNEA) produces fission Mo 99, an isotope of wide use in nuclear medicine. In order to simplify the current Mo 99 production process, to shorten its duration and reduce impurities in the final product, alternative methods for purification steps were looked for. In this work a variety of new materials for the purification columns were designed, all of them with carbon. These materials were studied and a material which contribute with the best results for molybdenum retention, was selected. The preparation procedure and the working conditions were determined. (author)

Process for producing molybdenum foil and collapsible tubing

Science.gov (United States)

Bretts, G. R.; Gavert, R. B.; Groschke, G. F.

1971-01-01

Manufacturing process produces molybdenum foil 0.002 cm thick and 305 m long, and forms foil into high-strength, thin-walled tubing which can be flattened for storage on a spool. Desirable metal properties include high thermal conductivity stiffness, yield and tensile stress, and low thermal expansion coeffecient.

Investigation of molybdenum-crosslinker interfaces for affinity based electrochemical biosensing applications

Science.gov (United States)

Kamakoti, Vikramshankar; Shanmugam, Nandhinee Radha; Tanak, Ambalika Sanjeev; Jagannath, Badrinath; Prasad, Shalini

2018-04-01

Molybdenum (Mo) has been investigated for implementation as an electrode material for affinity based biosensing towards devloping flexibe electronic biosensors. Treatment of the native oxide of molybdenum was investigated through two surface treatment strategies namely thiol and carbodiimide crosslinking methods. The binding interaction between cross-linker molecules and Mo electrode surface has been characterized using Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and optical microscopy. The efficacy of treatment of Mo with its native oxide using carbodiimide cross linking methodology was established. The carbodiimide cross-linking chemistry was found to possess better surface coverage and binding affinity with Molybdenum electrode surface when compared to thiol cross-linking chemistry.Electrochemical characterization of Mo electrode using Electrochemical Impedance Spectroscopy (EIS) and Cyclic Voltametry (CV) techniques was performed to evaluate the effect of ionic properties of solution buffer on the Mo electrode's performance. Affinity based biosensing of C-Reactive Protein (CRP) has been demonstrated on a flexible nanoporous polymeric substrate with detection threshold of 100 pg/ml in synthetic urine buffer medium. The biosensor has been evaluated to be developed as a dipstick based point of care device for detection of biomarkers in urine.

Catalytic activity of oxide cerium-molybdenum-tellurium catalysts in oxidation ammonolysis

International Nuclear Information System (INIS)

Dzhordano, N.; Bart, D.; Madzhori, R.

1984-01-01

A commercial catalyst containing a mixture of Ce-, Mo-, Te oxides deposited on SiO 2 is shown to manifest a high efficiency in oxidative ammonolysis of propylene (C 3 - ) to acrylonitrile (AN). The dependence of the catalytic properties on the catalyst composition and reaction conditions is studied. It is established that three-component mixtures are more active and selective than the systems with a lesser number of components. Using the catalyst with the optimum ratio of constituent oxides in a microreactor at 440 deg enabled one to achieve initial selectivity in terms of AN equal to 82.5% at 97% conversion of C 3 - . Acrolein, acetonitrile, HCN and nitrogen oxides are the reaction by-products. A supposition is made that the reaction proceeds via the formation of π-compleXes on the centres of Te(4). Setective oxidation occurs on oxygen atoms bonded with the Mo(6) ions. Tellurium enhances the molybdenum reducibleness due to delocalization of electrons, whereas the cerium addition to the mixture of tellurium- and molybdenum oxides increases the rate of molybdenum reoxidation and thus enhances the catalytic system stability

Determination of molybdenum in natural waters by laser thermal-lens spectrometry

International Nuclear Information System (INIS)

Proskurnin, M.A.; Abroskin, A.G.; Artemova, S.I.; Belyaeva, T.V.; Ivanova, E.K.

1992-01-01

As before, the determination of nanogram quantities of heavy metals from small sample volumes of natural water represents an acute problem. This task has been solved more or less successfully by the use of different and sufficiently developed physicochemical methods. In most cases the determination requires a 100-fold preconcentration of the component determined (for instance, when using atomic absorption spectrometry). This significant disadvantage can be avoided by the use of thermal-lens laser spectrometry (TLS); some alternatives of the method have already found applications in analytical practice. The objective of the present study has been to investigate the optimum conditions for the determination of molybdenum in natural waters from small sample volumes by TLS. The resulting method based on the reaction with thiocyanate ions in the presence of ascorbic acid, has a detection limit of 19 pg/ml. Masking of iron(III) with a 1000-fold excess of tartrate ions has been proposed and it has been shown that a 10-fold excess of iron does not interfere in the determination of molybdenum. The procedure has been applied to the determination of molybdenum in drinking and natural waters

Problems in producing nuclear reactor for medical isotopes and the Global Crisis of molybdenum supply

International Nuclear Information System (INIS)

Zubiarrain, A.

2011-01-01

Nuclear medicine uses drugs that incorporate a radioactive isotope radiopharmaceuticals. Every year are performed, worldwide, 35 million nuclear medicine procedures, of which 80% are done with radiopharmaceuticals containing the isotope, molybdenum-99, produced in nuclear reactors. In recent years, there have been several supply crisis of molybdenum-99, which have hampered diagnostic procedure with technitium-99m. (Author)

Production of molybdenum-99 by heterogeneous and homogeneous uranium fueled reactors

International Nuclear Information System (INIS)

Carlin, G.E.; Bonin, H.W.

2012-01-01

The use of radioisotopes for various procedures in the health care industry has become one of the most important practices in medicine. At the forefront of the medical isotope list is molybdenum-99 and its daughter isotope technetium-99m, which encompass over 80% of radiopharmaceutical procedures. Fission of uranium-235 to produce molybdenum-99 is the most widely used method for producing this radioisotope. The heterogeneous reactor and the aqueous homogeneous reactor are looked at here with emphasis on the use of low enriched uranium as the fuel source. Methods of technetium-99m generation and its medical use are also reviewed. (author)

Production of molybdenum-99 by heterogeneous and homogeneous uranium fueled reactors

Energy Technology Data Exchange (ETDEWEB)

Carlin, G.E.; Bonin, H.W., E-mail: george.carlin@rmc.ca, E-mail: bonin-h@rmc.ca [Royal Military College of Canada, Kingston, Ontario (Canada)

2012-07-01

The use of radioisotopes for various procedures in the health care industry has become one of the most important practices in medicine. At the forefront of the medical isotope list is molybdenum-99 and its daughter isotope technetium-99m, which encompass over 80% of radiopharmaceutical procedures. Fission of uranium-235 to produce molybdenum-99 is the most widely used method for producing this radioisotope. The heterogeneous reactor and the aqueous homogeneous reactor are looked at here with emphasis on the use of low enriched uranium as the fuel source. Methods of technetium-99m generation and its medical use are also reviewed. (author)

The effect of molybdenum on the grain boundary segregation of phosphorus in steel

International Nuclear Information System (INIS)

Moller, R.; Brenner, S.S.; Grabke, A.J.

1986-01-01

The beneficial effect of molybdenum on the temper embrittlement of steels is well known but has not yet been satisfactorily explained. Yu and McMahon suggested a strong interaction between molybdenum and phosphorus to form Mo-P clusters which decrease the concentration of phosphorus in the matrix and consequently the amount segregated to grain boundaries. Such clusters have as yet not been observed but this may have been owing to the insufficient resolution of conventional analytical methods. However, since no scavenging of phosphorus was observed in carbon-free Fe-Mo-P alloys, i.e. Mo alone did not affect the grain boundary concentration of phosphorus, it is improbable that the Mo-P cluster formation mechanisms can be operative. Instead, it is more likely that a requisite for the scavenging of phosphorus is the formation of Mo carbides in the steel. This work was undertaken to determine the distribution of phosphorus in two similar Fe-Mo-P alloys, one of which contained carbon while the other was carbon-free. The emphasis of the study was to determine the interaction of phosphorus with molybdenum and molybdenum carbides in the steel. Field-ion microscopy combined with atom probe microanalysis was used for this purpose. The atom-by-atom sampling method and the near-atomic spatial resolution of the FIM/atom probe make this instrument ideally suited for this type of investigations

Novel target configurations for selective ionization state studies in molybdenum

International Nuclear Information System (INIS)

Ilcisin, K.J.; Feldman, U.; Schwob, J.L.; Wouters, A.; Suckewer, S.; Princeton Univ., NJ

1990-03-01

Details of experiments aimed at achieving low ionization state selectivity in molybdenum are presented. Targets are excited with a 10 J CO 2 laser and the resultant VUV spectrum (300--700 Angstrom) has been studied. Combinations of focal spot size, target depth, and target geometries are compared. Simple attenuation of energy is shown not to vary ionization stage composition significantly. Experiments conducted with grazing incidence targets result only in a hot plasma. Modular targets with cooling cylinders of various radii demonstrated good selectivity of the ionization states, but with low absolute signals. Finally, results from combinations of focal spot adjustment and radiative cooling illustrate increased control over desired plasma temperature and density for spectroscopic studies of molybdenum. 7 refs., 14 figs

Tensile properties of electron-beam-welded single crystals of molybdenum

International Nuclear Information System (INIS)

Hiraoka, Yutaka; Okada, Masatoshi; Irie, Hirosada; Fujii, Tadayuki.

1987-01-01

The purpose of this study is to investigate the macro- and microstructures and the tensile properties of electron-beam-welded single crystals of molybdenum. The single-crystal sheets were prepared by means of secondary recrystallization. The welding was carried out by a melt-run technique. The weld metal had the same crystallographic orientation as the base metal, and no grain boundary was observed. However, many large weld pores were formed mostly along the weld bond. The strength and ductility of the welded joints of single crystals were almost the same as those of the base metal (''annealed'' single crystals). It is concluded that the joint efficiency of molybdenum single crystals at room temperature or above was excellent and nearly 100 %. (author)

Core conversion study from silicide to molybdenum fuel in the Indonesian 30 MW multipurpose reactor G.A. Siwabessy (RSG-GAS)

International Nuclear Information System (INIS)

Sembiring, T.M.; Kuntoro, I.

2005-01-01

This paper describes the core conversion from silicide to molybdenum core through a series of silicide (2.96 gU cm -3 ) - molybdenum (3.55 gUcm -3 ) mixed transition cores for the Indonesian 30 MW-Multipurpose G.A. Siwabessy (RSGGAS) reactor. The core calculations are carried out using the two-dimensional multigroup neutron diffusion method code of Batan-EQUIL-2D. The calculated results showed that the proposed silicide-molybdenum mixed transition cores, using the same refueling/reshuffling scheme, meet the safety criteria and it can be used in safely converting from an all-silicide core to an all-molybdenum core. (author)

Effect of white mineral trioxide aggregate compared with biomimetic carbonated apatite on dentine bridge formation and inflammatory response in a dental pulp model.

Science.gov (United States)

Danesh, F; Vahid, A; Jahanbani, J; Mashhadiabbas, F; Arman, E

2012-01-01

  To evaluate the effects of apatite precipitation on the biocompatibility and hard tissue induction properties of white mineral trioxide aggregate (WMTA) in a dental pulp model.   Pulp exposures were created on the axial walls of 32 sound canine teeth of eight dogs. Four additional sound teeth served as controls. The pulps were capped either with WMTA or apatite derivatives [biomimetic carbonated apatite (BCAp)] in the interaction of WMTA with a synthetic tissue fluid and restored with zinc oxide-eugenol cement. After 7 and 70 days, the animals were killed, and the histological specimens taken from the teeth were stained with haematoxylin and eosin for histomorphological evaluation. The Brown and Brenn technique was employed to stain bacteria. The data were subjected to nonparametric Kruskall-Wallis analysis and Mann-Whitney U_tests.   Biomimetic carbonated apatite did not induce hard tissue bridge formation. WMTA performed significantly better than BCAp in this respect at both periods (P 0.05).   White mineral trioxide aggregate induced hard tissue formation via a mechanism other than that postulated via apatite formation. © 2011 International Endodontic Journal.

Chemical effects of nuclear transformations in molybdenum complexes

International Nuclear Information System (INIS)

Millan S, S.A.

1977-01-01

The Szilard-Chalmers effect was studied in the complexes: tetraacetatedimolybdenum(II), tetrabenzoatedimolybdenum(II), benzenetricarbonylmolybdenym(0). The results we obtained in the measurement of the Szilard-Chalmers effect on the studied complexes imply some influence of the structure in the molecular fragmentation, or the conservation of the links molybdenum-ligands. (author)

Electroerosion resistance of tungsten-copper and molybdenum-copper pseudoalloys

International Nuclear Information System (INIS)

Nerus, L.N.; Verkhoturov, A.D.; Marek, B.A.; Mukha, I.M.

1977-01-01

Results of the study of electroerosion resistance of W-Cu and Mo-Cu pseudoalloys in a wide range of concentrations are presented. Tungsten alloys with 10-20% copper and pure molybdenum have exhibited the best erosion resistance at electrospark machining

Determination of molybdenum in human urine by electrothermal atomization atomic absorption spectrometry

International Nuclear Information System (INIS)

Pita Calvo, C.; Bermejo Barrera, P.; Bermejo Barrera, A.

1995-01-01

Various matrix modifiers were investigated for the determination of molybdenum in human urine samples by electrothermal atomization atomic absorption spectrometry. Methods with nitric acid, barium difluoride, magnesium nitrate, palladium-magnesium nitrate and palladium-hydroxylamine hydrochloride were studied by introducing the urine samples directly into the graphite furnace with 0.3% Triton X-100. The charring and atomization curves, the amount of modifier and the calibration and addition graphs were studied in all instances. The precision, accuracy and chemical interferences of the methods were also investigated. The matrix interferences have been removed with the modifiers barium difluoride, palladium-magnesium nitrate and palladium-hydroxylamine hydrochloride. The limits of detection and quantification were 0.2 and 0.7 μg l -1 , respectively, for these modifiers. The characteristic masses were 14.1, 18.0 and 14.9 pg of Mo for palladium-magnesium nitrate, palladium-hydroxylamine hydrochloride and barium difluoride, respectively. The method with palladium-magnesium nitrate has been applied to the study of the amount of molybdenum in human urine samples. The molybdenum levels found lie between 4.8-205.6 μg l -1

The structure and function of supported molybdenum nitride and molybdenum carbide hydrotreating catalysts

Science.gov (United States)

Dolce, Gregory Martin

1997-11-01

A series of gamma-Alsb2Osb3 supported molybdenum nitrides and carbides were prepared by the temperature programmed reaction of supported molybdates with ammonia and methane/hydrogen mixtures, respectively. In the first part of this research, the effects of synthesis heating rates and molybdenum loading on the catalytic properties of the materials were examined. A significant amount of excess carbon was deposited on the surface of the carbides during synthesis. The materials consisted of small particles which were very highly dispersed. Oxygen chemisorption indicated that the nitride particles may have been two-dimensional. The dispersion of the carbides, however, appeared to decrease as the loading increased. The catalysts were evaluated for hydrodenitrogenation (HDN), hydrodesulfurization (HDS), and hydrodeoxygenation (HDO). The molybdenum loading had the largest effect on the activity of the materials. For the nitrides, the HDN and HDS activities were inverse functions of the loading. This suggested that the most active HDN and HDS sites were located at the perimeter of the two-dimensional particles. The HDN and HDS activities of the carbides followed the same trend as the oxygen uptake. This result suggested that oxygen titrated the active sites on the supported carbides. Selected catalysts were evaluated for methylcarbazole HDN, dibenzothiophene HDS, and dibenzofuran HDO. The activity and selectivity of the nitrides and carbides were competitive with a presulfided commercial catalyst. In the second part of this work, a series of supported nitrides and carbides were prepared using a wider range of loadings (5-30 wt% Mo). Thermogravimetric analysis was used to determine the temperature at which excess carbon was deposited on the carbides. By modifying the synthesis parameters, the deposition of excess carbon was effectively inhibited. The dispersions of the supported nitrides and carbides were constant and suggested that the materials consisted of two

The effect of molybdenum addition on SCC susceptibility of stainless steels in oxygenated high temperature water

International Nuclear Information System (INIS)

Akashi, Masatsune; Kawamoto, Teruaki

1978-01-01

The effect of molybdenum addition on the SCC susceptibility of sensitized stainless steel in oxygenated high temperature water has been studied through the creviced bent beam SCC test (CBB test) and A262E intergranular corrosion test. The molybdenum addition improved the SCC susceptibility of sensitized stainless steels in oxygenated high temperature water not only by delaying the sensitization at lower temperatures but also by increasing the material resistance to the SCC under a given degree of sensitization. These laboratory test results reveal that the molybdenum addition is quite beneficial for improving the SCC susceptibility of stainless steel pipe weld joints in boiling water reactor environment. (auth.)

Neutronic and thermal hydraulic analysis for production of fission molybdenum-99 at Pakistan Research Reactor-1

Energy Technology Data Exchange (ETDEWEB)

Mushtaq, A. [Isotope Production Division, Pakistan Institute of Nuclear Science and Technology, P.O. Nilore, Islamabad (Pakistan)], E-mail: mushtaqa@pinstech.org.pk; Iqbal, Massod; Bokhari, Ishtiaq Hussain; Mahmood, Tariq; Mahmood, Tayyab; Ahmad, Zahoor; Zaman, Qamar [Nuclear Engineering Division, Pakistan Institute of Nuclear Science and Technology, P.O. Nilore, Islamabad (Pakistan)

2008-02-15

Neutronic and thermal hydraulic analysis for the fission molybdenum-99 production at PARR-1 has been performed. Low enriched uranium foil (<20% {sup 235}U) will be used as target material. Annular target designed by ANL (USA) will be irradiated in PARR-1 for the production of 100 Ci of molybdenum-99 at the end of irradiation, which will be sufficient to prepare required {sup 99}Mo/{sup 99m}Tc generators at PINSTECH and its supply in the country. Neutronic and thermal hydraulic analysis were performed using various codes. Data shows that annular targets can be safely irradiated in PARR-1 for production of required amount of fission molybdenum-99.

Molybdenum-99 supply: a global issue

International Nuclear Information System (INIS)

Cote, R.V.

2011-01-01

This article discusses the global supply of Molybdenum 99 used in nuclear medicine. Following a disruption in supplies of isotopes in the last few years, a Canadian expert panel assessed the most viable options for securing a sustainable supply of Technitium 99 over the medium to long term. The general recommendations were to strive for diversity and redundancy throughout the supply chain, leverage multi-use infrastructure, continue with international coordination and seek processing standardization within North America.

Effect of an intermediate tungsten layer on thermal properties of TiC coatings ion plated onto molybdenum

International Nuclear Information System (INIS)

Fukutomi, M.; Fujitsuka, M.; Shikama, T.; Okada, M.

1985-01-01

Among the various low-Z coating-substrate systems proposed for fusion reactor first-wall applications, molybdenum coated with titanium carbide is considered very promising since it has a good capability of receiving heat from the plasma. The thermal stabilities of TiC layers ion plated onto the molybdenum substrate are discussed with particular reference to the interfacial reaction between the TiC coating and molybdenum. The deposition of an intermediate tungsten layer was found to be very effective in suppressing the formation of reaction layers, resulting in a marked improvement in thermal stabilities of TiC--Mo systems. Thermal shock test using a pulsed electron beam showed that the TiC coatings remained adherent to the molybdenum substrates during energy depositions high enough to melt the substrates within the area of beam deposition. The melt area of the TiC coatings apparently decreased when a tungsten intermediate layer was applied

Mineral trioxide aggregate induces osteoblastogenesis via Atf6

Directory of Open Access Journals (Sweden)

Toyonobu Maeda

2015-06-01

Full Text Available Mineral trioxide aggregate (MTA has been recommended for various uses in endodontics. To understand the effects of MTA on alveolar bone, we examined whether MTA induces osteoblastic differentiation using MC3T3-E1 cells. MTA enhanced mineralization concomitant with alkaline phosphatase activity in a dose- and time-dependent manner. MTA increased production of collagens (Type I and Type III and matrix metalloproteinases (MMP-9 and MMP-13, suggesting that MTA affects bone matrix remodeling. MTA also induced Bglap (osteocalcin but not Bmp2 (bone morphogenetic protein-2 mRNA expression. We observed induction of Atf6 (activating transcription factor 6, an endoplasmic reticulum (ER stress response transcription factor mRNA expression and activation of Atf6 by MTA treatment. Forced expression of p50Atf6 (active form of Atf6 markedly enhanced Bglap mRNA expression. Chromatin immunoprecipitation assay was performed to investigate the increase in p50Atf6 binding to the Bglap promoter region by MTA treatment. Furthermore, knockdown of Atf6 gene expression by introduction of Tet-on Atf6 shRNA expression vector abrogated MTA-induced mineralization. These results suggest that MTA induces in vitro osteoblastogenesis through the Atf6–osteocalcin axis as ER stress signaling. Therefore, MTA in endodontic treatment may affect alveolar bone healing in the resorbed region caused by pulpal infection.

Liquid phase sintering of carbides using a nickel-molybdenum alloy

International Nuclear Information System (INIS)

Barranco, J.M.; Warenchak, R.A.

1987-01-01

Liquid phase vacuum sintering was used to densify four carbide groups. These were titanium carbide, tungsten carbide, vanadium carbide, and zirconium carbide. The liquid phase consisted of nickel with additions of molybdenum of from 6.25 to 50.0 weight percent at doubling increments. The liquid phase or binder comprised 10, 20, and 40 percent by weight of the pressed powders. The specimens were tested using 3 point bending. Tungsten carbide showed the greatest improvement in bend rupture strength, flexural modulus, fracture energy and hardness using 20 percent binder with lesser amounts of molybdenum (6.25 or 12.5 wt %) added to nickel compared to pure nickel. A refinement in the carbide microstructure and/or a reduction in porosity was seen for both the titanium and tungsten carbides when the alloy binder was used compared to using the nickel alone. Curves depicting the above properties are shown for increasing amounts of molybdenum in nickel for each carbide examined. Loss of binder phase due to evaporation was experienced during heating in vacuum at sintering temperatures. In an effort to reduce porosity, identical specimens were HIP processed at 15 ksi and temperatures averaging 110 C below the sintering g temperature. The tungsten carbide and titanium carbide series containing 80 and 90 weight percent carbide phase respectively showed improvement properties after HIP while properties decreased for most other compositions

Electrical Transport Properties of Polycrystalline Monolayer Molybdenum Disulfide

Science.gov (United States)

2014-07-14

Lou, Sina Najmaei, Matin Amani, Matthew L. Chin, Zheng Se. TASK NUMBER Liu Sf. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAMES AND ADDRESSES 8...Transport Properties of Polycrystalline Monolayer Molybdenum Disulfide Sina Najmaei,t.§ Matin Ama ni,M Matthew L. Chin,* Zhe ng liu/ ·"·v: A. Gle n

Surface analyses of TiC coated molybdenum limiter material exposed to high heat flux electron beam

International Nuclear Information System (INIS)

Onozuka, M.; Uchikawa, T.; Yamao, H.; Kawai, H.; Kousaku, A.; Nakamura, H.; Niikura, S.

1987-01-01

Observation and surface analyses of TiC coated molybdenum exposed to high heat flux have been performed to study thermal damage resistance of TiC coated molybdenum limiter material. High heat loads were provided by a 120 kW electron beam facility. SEM, AES and EPMA have been applied to the surface analyses

Reaction between molybdenum hexafluoride and carboxylic acids

International Nuclear Information System (INIS)

Shustov, L.D.; Nikolenko, L.N.; Senchenkova, T.M.

1983-01-01

Trifluoromethyl derivatives of pyridine, imidazole and difluoromethane are synthesized during interaction of MoF 6 surplUs (190-210 deg) with nicotine-isomicotine-, 2,6-pyridinedicarboxylic-, 4,5-imidazoledicarboxyclic- and diffluoroacetic acids. The yield of trifluoromethyl derivatives attains 84%. Molybdenum hexafluoride offers some advantages in comparisoo with toxic SF 4 . MoF 6 toxicity is low; leakage of MoF 6 vapors is easily detected

Effect of dispersed particles of calcium fluoride on the molybdenum solubility in iron

International Nuclear Information System (INIS)

Shvejkin, G.P.; Antsiferov, V.N.; Postnikov, V.S.

1981-01-01

The results of the investigation of compositions containing 20 at% Mo and 12 vol.% CaF 2 are presented. The sample diffractograms of compositions Fe+20 at% Mo and (Fe+20 at% Mo)+12 vol.% CaF 2 are given. It is shown that the introduction of calcium fluoride results in formation of continuos series of solid solutions of molybdenum in iron. The results of X-ray diffraction investigations on exceeding solubility limit of molybdenum in iron in the presence of calcium fluoride are confirmed

The extended family of hexagonal molybdenum oxide

Energy Technology Data Exchange (ETDEWEB)

Hartl, Monika [Los Alamos National Laboratory; Daemen, Luke [Los Alamos National Laboratory; Lunk, J H [NON LANL; Hartl, H [NON LANL; Frisk, A T [NON LANL; Shendervich, I [NON LANL; Mauder, D [NON LANL; Feist, M [NON LANL; Eckelt, R [NON LANL

2009-01-01

Over the last 40 years, a large number of isostructural compounds in the system MoO{sub 3}-NH{sub 3}-H{sub 2}O have been published. The reported molecular formulae of 'hexagonal molybdenum oxide' (HEMO) varied from MoO{sub 3}, MoO{sub 3} {center_dot} 0.33NH{sub 3}, MoO{sub 3} {center_dot} nH{sub 2}O (0.09 {le} n {le} 0.69) to MoO{sub 3} {center_dot} mNH{sub 3} {center_dot} nH{sub 2}O (0.09 {le} m {le} 0.20; 0.18 {le} n {le} 0.60). Samples, prepared by the acidification route, were investigated using thermal analysis coupled on-line to a mass spectrometer for evolved gas analysis; X-ray powder diffraction; Fourier Transform Infrared, Raman and Magic-Angle-Spinning {sup 1}H-NMR spectroscopy; Incoherent Inelastic Neutron Scattering. The X-ray study of a selected monocrystal confirmed the presence of the well-known framework of edge-sharing MoO{sub 6} octahedra: Space group P6{sub 3}/m, a = 10.527(1), c =3.7245(7) {angstrom}, {gamma} = 120{sup o}. The structure of the synthesized samples can best be described by the structural formula (NH{sub 4})[Mo{sub x}{open_square}{sub 1/2+p/2}(O{sub 3x + 1/2-p/2})(OH){sub p}] {center_dot} yH{sub 2}O (x 5.9-7.1; p {approx} 0.1; y = 1.2-2.6), which is consistent with the existence of one vacancy for 12-15 molybdenum sites. The 'chimie douce' reaction of MoO{sub 3} {center_dot} 0.155NH{sub 3} {center_dot} 0.440H{sub 2}O with a 1:1 mixture of NO/NO{sub 2} at 100 C resulted in the synthesis of MoO{sub 3} {center_dot} 0.539H{sub 2}O. Tailored nano-sized molybdenum powders can be produced using HEMO as precursor.

Catalytic dehydrogenation of alcohol over solid-state molybdenum sulfide clusters with an octahedral metal framework

Energy Technology Data Exchange (ETDEWEB)

Kamiguchi, Satoshi, E-mail: kamigu@riken.jp [Advanced Catalysis Research Group, RIKEN Center for Sustainable Resource Science, 2-1 Hirosawa, Wako City, Saitama 351-0198 (Japan); Organometallic Chemistry Laboratory, RIKEN, 2-1 Hirosawa, Wako City, Saitama 351-0198 (Japan); Okumura, Kazu [School of Advanced Engineering, Kogakuin University, Nakano-machi, Hachioji City, Tokyo 192-0015 (Japan); Nagashima, Sayoko; Chihara, Teiji [Graduate School of Science and Engineering, Saitama University, Shimo-Okubo, Sakura-ku, Saitama City, Saitama 338-8570 (Japan)

2015-12-15

Graphical abstract: - Highlights: • Solid-state molybdenum sulfide clusters catalyzed the dehydrogenation of alcohol. • The dehydrogenation proceeded without the addition of any oxidants. • The catalytic activity developed when the cluster was activated at 300–500 °C in H{sub 2}. • The Lewis-acidic molybdenum atom and basic sulfur ligand were catalytically active. • The clusters function as bifunctional acid–base catalysts. - Abstract: Solid-state molybdenum sulfide clusters with an octahedral metal framework, the superconducting Chevrel phases, are applied to catalysis. A copper salt of a nonstoichiometric sulfur-deficient cluster, Cu{sub x}Mo{sub 6}S{sub 8–δ} (x = 2.94 and δ ≈ 0.3), is stored in air for more than 90 days. When the oxygenated cluster is thermally activated in a hydrogen stream above 300 °C, catalytic activity for the dehydrogenation of primary alcohols to aldehydes and secondary alcohols to ketones develops. The addition of pyridine or benzoic acid decreases the dehydrogenation activity, indicating that both a Lewis-acidic coordinatively unsaturated molybdenum atom and a basic sulfur ligand synergistically act as the catalytic active sites.

Determination of hafnium, molybdenum, and vanadium in niobium and niobium-based alloys by atomic absorption spectrometry

International Nuclear Information System (INIS)

Ide, Kunikazu; Kobayashi, Takeshi; Sudo, Emiko.

1985-01-01

The analytical procedure is as follows: Weigh 1 g of a sample and put it into a 100 cm 3 PTFE beaker. Add 5 ml of distilled water and 5 ml of hydrofluoric acid, and then heat the solution on a hot plate, adding 3 ml of nitric acid dropwise. Dilute the solution to 100 cm 3 with distilled water. When hafnium is determined, add 2 g of diammonium titanium hexafluoride ((NH 4 ) 2 TiF 6 )) before dilution. Working standard solutions are prepared by adding the stock standard solutions of hafnium, molybdenum, and vanadium into niobium solutions. When hafnium is determined, add 2 g of (NH 4 ) 2 TiF 6 and the alloying elements in amounts corresponding to those in sample solutions into the working standard solutions. The tolerable amounts of hydrofluoric acid were 2.9 M, 2.1 M, and 3.1 M and those of nitric acid were 1.0 M, 1.6 M, and 1.6 M for hafnium, molybdenum, and vanadium, respectively. It was found that (NH 4 ) 2 TiF 6 greatly increased the sensitivity for hafnium determination. Niobium showed minus effect for hafnium and plus effect for molybdenum and vanadium. The atomic absorption of molybdenum and vanadium were not influenced by the presence of 20 % of each alloying element, while the atomic absorption of hafnium was given plus effect by 20 % of zirconium, iron, cobalt, nickel, manganese, chromium or vanadium and minus effect by 20 % tungsten. The analytical values of hafnium, molybdenum, and vanadium in niobium-based alloys by this method showed a good agreement with those by X-ray fluorescence analysis. The lower limits of determination (S/N=2) were 0.05, 0.001, and 0.002 % and the relative standard deviation were 3, 1, and 1.5 % for hafnium, molybdenum, and vanadium, respectively. (author)

Effect of molybdenum on yield and nutrient content of the strawberry

International Nuclear Information System (INIS)

Bender, R.J.; Barros, I.B.I. de

1984-01-01

The cultivation of strawberries (Fragaria x ananassa Duch.) cv. Campinas in nutrient solution using five fields levels of molybdenum (MO), 0.010 ppm, 0.010 ppm, 0.10 ppm, 1.0 ppm and control (Without applying molybdenum). The experiment was carried out in greenhouse and phytothron to evaluate the changes in the mineral status of the leaves and the quality of the berries. The concentration of Mo in the leaves, at the beginning of fruiting stage, varied from 0.5 ppm to 64 ppm. The total N in the levels was affected significantly by Mo. Average weight of the berries were affected by treatments and presented a quadratic regression response. (M.A.C.) [pt

Effect of low fatigue on the ductile-brittle transition of molybdenum

International Nuclear Information System (INIS)

Furuya, K.; Nagata, N.; Watanabe, R.; Yoshida, H.

1982-01-01

An explicit ductile-brittle transition of molybdenum occurring in both tensile and low cycle fatigue tests was investigated. Tests were performed on several sorts of molybdenum and its alloy TZM, and effects of heat treatment, fabrication method and alloying on the transition behavior and fracture mode are described in detail. All the materials exhibited a brittle failure with degraded fatigue behavior at room temperature, while they became ductile as temperature increased up to 573 K. The tendency of fatigue results was qualitatively in accordance with that of reduction of area in tensile tests. Differences among the materials were minor on the ductile-brittle transition temperature (DBTT), but major on the fatigue life for the embrittled materials. (orig.)

Influence of Roughness on Quality Molybdenum Deposit Layer by Thermal Spraying

Directory of Open Access Journals (Sweden)

Marián Bujna

2016-01-01

Full Text Available In this paper we deal with the impact of roughness on the quality of molybdenum layer. Insufficient cleaning may result in a poor quality of the sprayed layer. Our aim is to analyze the influence of surface roughness on the quality of molybdenum layer thickness applied by thermal spraying. Thermal spraying influence several physical and chemical properties of the coating surface. The most important ones include: hardness, density, porosity, corrosion resistance and adhesion. This technology of surface treatment of material is often used for its high degree of hardness. Hardness and erosion resistance are the parameters that need to be achieved particularly in working conditions where there is excessive depreciation of a component.

Characterization of molybdenum particles reinforced Al6082 aluminum matrix composites with improved ductility produced using friction stir processing

Energy Technology Data Exchange (ETDEWEB)

Selvakumar, S., E-mail: lathaselvam1963@gmail.com [Department of Mechanical Engineering, Nehru Institute of Technology, Coimbatore 641105, Tamil Nadu (India); Department of Mechanical Engineering, Anna University, Chennai 600025, Tamil Nadu (India); Dinaharan, I., E-mail: dinaweld2009@gmail.com [Department of Mechanical Engineering Science, University of Johannesburg, Auckland Park Kingsway Campus, Johannesburg 2006 (South Africa); Palanivel, R., E-mail: rpalanivelme@gmail.com [Department of Mechanical Engineering Science, University of Johannesburg, Auckland Park Kingsway Campus, Johannesburg 2006 (South Africa); Ganesh Babu, B., E-mail: profbgb@gmail.com [Department of Mechanical Engineering, Roever College of Engineering and Technology, Perambalur 621212, Tamil Nadu (India)

2017-03-15

Aluminum matrix composites (AMCs) reinforced with various ceramic particles suffer a loss in ductility. Hard metallic particles can be used as reinforcement to improve ductility. The present investigation focuses on using molybdenum (Mo) as potential reinforcement for Mo(0,6,12 and 18 vol.%)/6082Al AMCs produced using friction stir processing (FSP). Mo particles were successfully retained in the aluminum matrix in its elemental form without any interfacial reaction. A homogenous distribution of Mo particles in the composite was achieved. The distribution was independent upon the region within the stir zone. The grains in the composites were refined considerably due to dynamic recrystallization and pinning effect. The tensile test results showed that Mo particles improved the strength of the composite without compromising on ductility. The fracture surfaces of the composites were characterized with deeply developed dimples confirming appreciable ductility. - Highlights: •Molybdenum particles used as reinforcement for aluminum composites to improve ductility. •Molybdenum particles were retained in elemental form without interfacial reaction. •Homogeneous dispersion of molybdenum particles were observed in the composite. •Molybdenum particles improved tensile strength without major loss in ductility. •Deeply developed dimples on the fracture surfaces confirmed improved ductility.

Characterization of molybdenum particles reinforced Al6082 aluminum matrix composites with improved ductility produced using friction stir processing

International Nuclear Information System (INIS)

Selvakumar, S.; Dinaharan, I.; Palanivel, R.; Ganesh Babu, B.

2017-01-01

Aluminum matrix composites (AMCs) reinforced with various ceramic particles suffer a loss in ductility. Hard metallic particles can be used as reinforcement to improve ductility. The present investigation focuses on using molybdenum (Mo) as potential reinforcement for Mo(0,6,12 and 18 vol.%)/6082Al AMCs produced using friction stir processing (FSP). Mo particles were successfully retained in the aluminum matrix in its elemental form without any interfacial reaction. A homogenous distribution of Mo particles in the composite was achieved. The distribution was independent upon the region within the stir zone. The grains in the composites were refined considerably due to dynamic recrystallization and pinning effect. The tensile test results showed that Mo particles improved the strength of the composite without compromising on ductility. The fracture surfaces of the composites were characterized with deeply developed dimples confirming appreciable ductility. - Highlights: •Molybdenum particles used as reinforcement for aluminum composites to improve ductility. •Molybdenum particles were retained in elemental form without interfacial reaction. •Homogeneous dispersion of molybdenum particles were observed in the composite. •Molybdenum particles improved tensile strength without major loss in ductility. •Deeply developed dimples on the fracture surfaces confirmed improved ductility.

Molybdenum-95 nuclear magnetic resonance of a series of phosphine and phosphite substituted molybdenum carbonyls Mo(CO)sub(6-n)Lsub(n)(n = 1,2,3,4,5)

International Nuclear Information System (INIS)

Jaitner, P.; Wohlgenannt, W.

1982-01-01

Molybdenum-95 NMR spectra of a series of phosphine and phosphite substituted molybdenum carbonyls Mo(CO)sub(6-n)Lsub(n)n[L = P(OCH 3 ) 3 n = 1,2,3,4,5, L = P(OC 2 H 5 ) 3 n = 1,2,3, L = P(C 6 H 5 ) 3 n = 1] including isomers (cis, trans, fac, mer) are reported. A large range of chemical shifts is found for the title compounds. The coupling constants 1 J( 95 Mo- 31 P) are derived either from 95 Mo-NMR spectra or 31 P-NMR spectra. Syntheses of the measured compounds were performed by thermal or photochemical ligand sustitution. (Author)

Compaction of Ceramic Microspheres, Spherical Molybdenum Powder and Other Materials to 3 GPa

International Nuclear Information System (INIS)

Carlson, S R; Bonner, B P; Ryerson, F J; Hart, M M

2006-01-01

Pressure-volume relationships were measured at room temperature for eight granular materials and one specimen of epoxy foam. The granular materials included hollow ceramic microspheres, spherical molybdenum powder, Ottawa sand, aluminum, copper, titanium and silicon carbide powders and glassy carbon spheres. Measurements were made to 0.9 GPa in a liquid medium press for all of the granular materials and to 3 GPa in a solid medium press for the ceramic microspheres and molybdenum powder. A single specimen of epoxy foam was compressed to 30 MPa in the liquid medium press. Bulk moduli were calculated as a function of pressure for the ceramic microspheres, the molybdenum powder and three other granular materials. The energy expended in compacting the granular materials was determined by numerically integrating pressure-volume curves. More energy was expended per unit volume in compacting the molybdenum powder to 1 GPa than for the other materials, but compaction of the ceramic microspheres required more energy per gram due to their very low initial density. The merge pressure, the pressure at which all porosity is removed, was estimated for each material by plotting porosity against pressure on a semi-log plot. The pressure-volume curves were then extrapolated to the predicted merge pressures and numerically integrated to estimate the energy required to reach full density for each material. The results suggest that the glassy carbon spheres and the ceramic microspheres would require more energy than the other materials to attain full density

Materials and Breakdown Phenomena: Heterogeneous Molybdenum Metallic Films

Directory of Open Access Journals (Sweden)

Augusto Marcelli

2017-05-01

Full Text Available Technological activities to design, manufacture, and test new accelerating devices using different materials and methods is under way all over the world. The main goal of these studies is to increase the accelerating gradients and reduce the probability of radio-frequency (RF breakdown. Indeed, it is still not clear why, by increasing the intensity of the applied field, intense surface damage is observed in copper structures, limiting the lifetime and, therefore, the practical applications. A possible solution is represented by a coating of a relatively thick layer of molybdenum in order to improve the breakdown rate. molybdenum can be reliably grown on different substrates with a negligible strain and, for thicknesses up to 600 nm, with a resistivity < 100–150·μΩ cm. Moreover, Mo coatings with controlled composition, internal stress, and roughness may allow improving thermo-mechanical properties reaching values not attainable by uncoated copper. Although the Mo conductivity remains lower compared to Cu, a Mo coating represents a very interesting option for high gradient accelerator components manufactured in copper.

Will mineral trioxide aggregate replace calcium hydroxide in treating pulpal and periodontal healing complications subsequent to dental trauma?

DEFF Research Database (Denmark)

Bakland, Leif K; Andreasen, Jens O

2012-01-01

Mineral trioxide aggregate (MTA) has over the last two decades begun to take the place of calcium hydroxide (CH) in the treatment of a variety of pulpal and periodontal healing complications following dental trauma. These conditions include teeth with: (i) exposed pulps, (ii) immature roots......, the quality of such induced hard tissues, and finally the dentin weakening effect of CH, which in some instances lead to cervical root fractures in immature teeth. MTA appears, from a relatively few clinical studies, to overcome these shortcomings of CH. The lack of long-term clinical studies, however, may...

Differential pulse polarographic determination of molybdenum (VI) in phosphoric medium by benzoin alpha oxime

International Nuclear Information System (INIS)

Chergouche, S.

1992-02-01

The extraction of Molybdenum (VI) using both 4-Methylpentane-2-one (hexone) and chloroform dissolved Benzoin-alpha-oxime has been investigated in order to develop a simple and sensitive polarographic method allowing the analysis of Molybdenum (VI) contained in industrial phosphoric acid produced in ANNABA (Eastern Algeria). The investigation takes into account various parameters such as: The stirring time, solvent rate, the number of stages ... as well as the organic phase conditioning during the polarographic analysis

78 FR 59679 - Antimony Trioxide TSCA Chemical Risk Assessment; Notice of Public Meetings and Opportunity To...

Science.gov (United States)

2013-09-27

...EPA's contractor, The Scientific Consulting Group (SCG), Inc., has identified a panel of scientific experts to conduct a peer review of EPA's draft Toxic Substances Control Act (TSCA) chemical risk assessment, ``TSCA Workplan Chemical Risk Assessment for Antimony Trioxide.'' EPA will hold three peer review meetings by web connect and teleconference. EPA invites the public to register to attend the meetings as observers and/or speakers providing oral comments during any or all of the peer review meetings as discussed in this notice. The public may also provide comment on whether they believe the appearance of conflict of interest exists for any proposed peer review panel expert.

The antitumor effect of arsenic trioxide on hepatocellular carcinoma is enhanced by andrographolide.

Science.gov (United States)

Duan, Xuhua; Li, Tengfei; Han, Xinwei; Ren, Jianzhuang; Chen, Pengfei; Li, Hao; Gong, Shaojun

2017-10-31

High concentrations of arsenic trioxide (As 2 O 3 ) are used to treat acute promyelocytic leukemia and solid tumors, with negative side effects to normal cells. Andrographolide is a traditional Chinese medicine that exerts anti-cancer, anti-inflammatory, anti-virus, and anti-diabetic effects. Here, we tested the effects of combined andrographolide with As 2 O 3 against hepatocellular carcinoma (HCC). We found that by increasing apoptosis, andrographolide synergistically enhanced the anti-tumor effects of As2O3 in HepG2 cells in vitro and in vivo . Furthermore, results from our microarray assays and experiments with mouse xenografts showed that EphB4 was downregulated by the combination of As 2 O 3 plus andrographolide. These findings suggest that the combination of andrographolide and As 2 O 3 could yield therapeutic benefits in the treatment of HCC.

Chromium and molybdenum diffusion in tungsten single crystals

International Nuclear Information System (INIS)

Klotsman, S.M.; Koloskov, V.M.; Osetrov, S.V.; Polikarpova, I.P.; Tatarinova, G.N.; Timofeev, A.N.

1989-01-01

Consideration is given to results of measuring temperature dependences of diffusion coefficients of homovalent impurities of chromium and molybdenum in tungsten single crystals. It is concluded that the difference of activation energies of selfdiffusion and impurity diffusion in the system 'tungsten-homovalent impurity' is conditioned by interaction of screened potentials of impurity and vacancy with Lazarus-Le Claire model

ISOLATION AND CHARACTERIZATION OF A MOLYBDENUM-REDUCING, PHENOL- AND CATECHOL-DEGRADING PSEUDOMONAS PUTIDA STRAIN AMR-12 IN SOILS FROM EGYPT

Directory of Open Access Journals (Sweden)

M. Abd. AbdEl-Mongy

2016-02-01

Full Text Available Sites contaminated with both heavy metals and organic xenobiotic pollutants warrants the effective use of either a multitude of bacterial degraders or bacteria having the capacity to detoxify numerous toxicants simultaneously. A molybdenum-reducing bacterium with the capacity to degrade phenolics is reported. Molybdenum (sodium molybdate reduction was optimum between pH 6.0 and 7.0 and between 20 and 30 °C. The most suitable electron donor was glucose. A narrow range of phosphate concentrations between 5.0 and 7.5 mM was required for optimal reduction, while molybdate between 20 and 30 mM were needed for optimal reduction. The scanning absorption spectrum of the molybdenum blue produced indicated that Mo-blue is a reduced phosphomolybdate. Molybdenum reduction was inhibited by the heavy metals mercury, silver and chromium. Biochemical analysis identified the bacterium as Pseudomonas putida strain Amr-12. Phenol and phenolics cannot support molybdenum reduction. However, the bacterium was able to grow on the phenolic compounds (phenol and catechol with observable lag periods. Maximum growth on phenol and catechol occurred around the concentrations of 600 mg∙L-1. The ability of this bacterium to detoxify molybdenum and grown on toxic phenolic makes this bacterium an important tool for bioremediation.

Determination of molybdenum (VI) by its catalytic effect on the oxidation of nile blue by hydrogen peroxide

International Nuclear Information System (INIS)

Ensafi, Ali A.; Sadeghie, Majid M.; Alaie-Yazdie, F.

1998-01-01

A spectrophotometric reaction rate method for the determination of molybdenum is described, based on its catalytic effect on the oxidation of nile blue by hydrogen peroxide. The decrease in absorbance of nile blue with time from 0.5 to 4 min at 590 nm is proportional to the concentration of Mo(VI) over the range 0.022-1000 μg/ml. The limit of detection of molybdenum(VI) is 0.008 μg/ml. The precision and the effect of more than forty ions are reported. The procedure has been successfully applied for the determination of molybdenum (VI) in plant materials and steel samples. (author)

Chitosan-coated magnetite nanoparticles as adsorbent for the removal of molybdenum ions

International Nuclear Information System (INIS)

Sousa, Jose S.; Egute, Nayara S.; Yamaura, Mitiko; Freitas, Antonio A.; Holland, Helber; Lugao, Ademar B.

2011-01-01

Metal ions in wastewater, even at low concentrations, affect a large number of organisms due to their high degree of toxicity. Research has developed some alternative methods for metal removal from the wastewater, as adsorption using a bio sorbent of combined chitosan with magnetic particles. Chitosan is a natural bio polymer, which has a highly reactive active sites in its structure, composed of amino and hydroxyl groups with affinity to bind to metal ions. In this study, magnetic nanoparticles of coated magnetite with chitosan as an adsorbent of molybdenum(Vi) ions in aqueous medium was investigated. The adsorption experiments were performed varying the time contact from 5 to 150 min, the p H from 0.5 to 11 and the molybdenum concentrations in nitric solutions. All molybdenum analyses were carried out by gamma spectroscopy using a Hp Ge detector and 99 Mo as radioactive tracer. Results showed that the chitosan-coated magnetite particles are good adsorbent for Mo ions from aqueous medium in the range of p H from 0.5 to 9 with a removal higher than 99%. Among the studied isotherm models, the Freundlich model fitted best the equilibrium adsorption isotherm of Mo(VI) ions. (author)

Separation of Molybdenum from Acidic High-Phosphorus Tungsten Solution by Solvent Extraction

Science.gov (United States)

Li, Yongli; Zhao, Zhongwei

2017-10-01

A solvent-extraction process for deep separation of molybdenum from an acidic high-phosphate tungsten solution was developed using tributyl phosphate (TBP) as the extractant and hydrogen peroxide (H2O2) as a complexing agent. The common aqueous complexes of tungsten and molybdenum (PMoxW12-xO40 3-, x = 0-12) are depolymerized to {PO4[Mo(O)2(O-O)]4}3- and {PO4[W(O)2(O-O)]4}3- by H2O2. The former can be preferentially extracted by TBP. The extractant concentration, phase contact time, H2O2 dosage, and H2SO4 concentration were optimized. By employing 80% by volume TBP, O:A = 1:1, 1.0 mol/L H2SO4, 1.0 mol/L H3PO4, a contact time of 2 min, and a molar ratio of H2O2/(W + Mo) equal to 1.5, 60.2% molybdenum was extracted in a single stage, while limiting tungsten co-extraction to 3.2%. An extraction isotherm indicated that the raffinate could be reduced to <0.1 g/L Mo in six stages of continuous counter-current extraction.

On molybdenum (6) alcoholates

International Nuclear Information System (INIS)

Turova, N.Ya.; Kessler, V.G.

1990-01-01

Synthesis techniques for molybdenum (6) alcoholates of MoO(OR) 4 (1) and MoO 2 (OR) 2 (2) series by means of exchange interaction of corresponding oxychloride with MOR (M=Li, Na) are obtained. These techniques have allowed to prepare 1(R=Me, Et, i-Pr) and 2(R=Me, Et) with 70-98 % yield. Methylates are also prepared at ether interchange of ethylates by methyl alcohol. Metal anode oxidation in corresponding alcohol may be used for 1 synthesis. Physicochemical properties of both series alcoholates, solubility in alcohols in particular, depend on their formation conditions coordination polymerism. Alcoholates of 1 are rather unstable and tend to decomposition up to 2 and ether. It is suggested to introduce NaOR microquantities to stabilize those alcoholates

Molybdenum Tube Characterization report

Energy Technology Data Exchange (ETDEWEB)

Beaux II, Miles Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Usov, Igor Olegovich [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-02-07

Chemical vapor deposition (CVD) techniques have been utilized to produce free-standing molybdenum tubes with the end goal of nuclear fuel clad applications. In order to produce tubes with properties desirable for this application, deposition rates were lowered requiring long deposition durations on the order of 50 hours. Standard CVD methods as well as fluidized-bed CVD (FBCVD) methods were applied towards these objectives. Characterization of the tubes produced in this manner revealed material suitable for fuel clad applications, but lacking necessary uniformity across the length of the tubes. The production of freestanding Mo tubes that possess the desired properties across their entire length represents an engineering challenge that can be overcome in a next iteration of the deposition system.

Spectrographic analysis of uranium-molybdenum alloys; Analisis espectrografico de aleaciones uranio-molibdeno

Energy Technology Data Exchange (ETDEWEB)

Roca, M

1967-07-01

A spectrographic method of analysis has been developed for uranium-molybdenum alloys containing up to 10 % Mo. The carrier distillation technique, with gallium oxide and graphite as carriers, is used for the semiquantitative determination of Al, Cr, Fe, Ni and Si, involving the conversion of the samples into oxides. As a consequence of the study of the influence of the molybdenum on the line intensities, it is useful to prepare only one set of standards with 0,6 % MoO{sub 3}. Total burning excitation is used for calcium, employing two sets of standards with 0,6 and 7.5 MoO{sub 3}. (Author) 5 refs.

22.5% efficient silicon heterojunction solar cell with molybdenum oxide hole collector

Energy Technology Data Exchange (ETDEWEB)

Geissbühler, Jonas, E-mail: jonas.geissbuehler@epfl.ch; Werner, Jérémie; Martin de Nicolas, Silvia; Hessler-Wyser, Aïcha; Tomasi, Andrea; Niesen, Bjoern; De Wolf, Stefaan [Photovoltaics and Thin Film Electronics Laboratory, Institute of Microengineering (IMT), École Polytechnique Fédérale de Lausanne (EPFL), Rue de la Maladière 71b, CH-2000 Neuchâtel (Switzerland); Barraud, Loris; Despeisse, Matthieu; Nicolay, Sylvain [CSEM PV-Center, Jaquet-Droz 1, CH-2000 Neuchâtel (Switzerland); Ballif, Christophe [Photovoltaics and Thin Film Electronics Laboratory, Institute of Microengineering (IMT), École Polytechnique Fédérale de Lausanne (EPFL), Rue de la Maladière 71b, CH-2000 Neuchâtel (Switzerland); CSEM PV-Center, Jaquet-Droz 1, CH-2000 Neuchâtel (Switzerland)

2015-08-24

Substituting the doped amorphous silicon films at the front of silicon heterojunction solar cells with wide-bandgap transition metal oxides can mitigate parasitic light absorption losses. This was recently proven by replacing p-type amorphous silicon with molybdenum oxide films. In this article, we evidence that annealing above 130 °C—often needed for the curing of printed metal contacts—detrimentally impacts hole collection of such devices. We circumvent this issue by using electrodeposited copper front metallization and demonstrate a silicon heterojunction solar cell with molybdenum oxide hole collector, featuring a fill factor value higher than 80% and certified energy conversion efficiency of 22.5%.

MHD simulations of molybdenum X-pinches

International Nuclear Information System (INIS)

Ivanenkov, G.V.; Stepnevski, V.

2002-01-01

One investigates into compression of molybdenum X-pinches applying numerical MHD-models with parabolic and conical initial geometry. The second model describing plasma axial motion in greater detail offers a real geometry of a discharge and is applicable to loads characterized by higher masses in contrast to the first one. Both models enabled to describe all basic phases of compression including origination of a minidiode, occurrence of a narrow neck, microexplosion of a hot point and origination of shock waves followed by sausage instability [ru

Spectra from foil-excited molybdenum ions

International Nuclear Information System (INIS)

Johnson, B.M.; Jones, K.W.; Cecchi, J.L.; Kruse, T.H.

1978-01-01

The extreme-ultraviolet spectra (5 to 55 nm) for foil-excited molybdenum ions have been measured using 22 to 200 MeV beams from the Brookhaven National Laboratory MP tandem Van de Graaff accelerator facility, 20 μg/cm 2 C stripping foils, and a grazing incidence spectrometer. The mean ion charge states (13 to 28) and the narrow distribution widths (about 2 charge states) were accurately predictable from experimental parameters. Where possible, comparisons are given with Mo radiation from tokamaks, vacuum sparks, and laser-excited plasmas

Development of the copper and molybdenum industries and the Armenian economy

Science.gov (United States)

Bond, A.R.; Levine, R.M.

1997-01-01

Production of copper and molybdenum in Armenia is examined, with special emphasis on the location of major deposits, former and proposed future centers of processing, and contribution of metals exports to the country's foreign trade revenues. Particular emphasis is placed on the impacts on these industries of the disruption of economic ties resulting from the dissolution of the USSR and an economic crisis precipitated by a major earthquake, Armenia's tension with Azerbaijan over armed conflict in Nagorno-Karabakh and surrounding areas in Azerbaijan, an economic blockade imposed by Turkey and Azerbaijan, and a consequent severe energy crisis. The paper highlights developments in the mid-1990s in copper and molybdenum and in the recent expansion of trade relations with Iran.

Immediate and delayed solubility of mineral trioxide aggregate and Portland cement

Directory of Open Access Journals (Sweden)

Augusto Bodanezi

2008-04-01

Full Text Available This study investigated the solubility of mineral trioxide aggregate (MTA and Portland cement since its mixture until 672 hours, by means of two complimentary methods. Metal ring molds filled with the cements were covered with distilled water and, at each experimental time (3, 24, 72, 168, 336 and 672 hours, were weighed as soon as the plates in which the samples have been placed. Empty rings served as the control group (n=8. Mean weight gain and loss was determined and analyzed statistically by two-way ANOVA and Tukey's test for all pairwise comparisons. Only Portland cement showed less than 3% weight loss through 24 hours. Detached MTA residues were heavier than those of Portland cement over the 3 to 168 hours. The weight of MTA rings increased more than that of Portland rings within 672 hours (p=0.05. The findings of the present study indicate that, in an aqueous environment MTA is more soluble than Portland cement and exceeds the maximum weight loss considered acceptable by ISO 6876 standard (2001.

Immediate and delayed solubility of mineral trioxide aggregate and Portland cement.

Science.gov (United States)

Bodanezi, Augusto; Carvalho, Nara; Silva, Daniela; Bernardineli, Norberti; Bramante, Clovis Monteiro; Garcia, Roberto Brandão; de Moraes, Ivaldo Gomes

2008-01-01

This study investigated the solubility of mineral trioxide aggregate (MTA) and Portland cement since its mixture until 672 hours, by means of two complimentary methods. Metal ring molds filled with the cements were covered with distilled water and, at each experimental time (3, 24, 72, 168, 336 and 672 hours), were weighed as soon as the plates in which the samples have been placed. Empty rings served as the control group (n=8). Mean weight gain and loss was determined and analyzed statistically by two-way ANOVA and Tukey's test for all pairwise comparisons. Only Portland cement showed less than 3% weight loss through 24 hours. Detached MTA residues were heavier than those of Portland cement over the 3 to 168 hours. The weight of MTA rings increased more than that of Portland rings within 672 hours (p=0.05). The findings of the present study indicate that, in an aqueous environment MTA is more soluble than Portland cement and exceeds the maximum weight loss considered acceptable by ISO 6876 standard (2001).

Method for preparing microstructure arrays on the surface of thin film material

KAUST Repository

Wang, Peng; Tang, Bo; Zhang, Lianbin

2017-01-01

Methods are provided for growing a thin film of a nanoscale material. Thin films of nanoscale materials are also provided. The films can be grown with microscale patterning. The method can include vacuum filtration of a solution containing the nanostructured material through a porous substrate. The porous substrate can have a pore size that is comparable to the size of the nanoscale material. By patterning the pores on the surface of the substrate, a film can be grown having the pattern on a surface of the thin film, including on the top surface opposite the substrate. The nanoscale material can be graphene, graphene oxide, reduced graphene oxide, molybdenum disulfide, hexagonal boron nitride, tungsten diselenide, molybdenum trioxide, or clays such as montmorillonite or lapnotie. The porous substrate can be a porous organic or inorganic membrane, a silicon stencil membrane, or similar membrane having pore sizes on the order of microns.

Method for preparing microstructure arrays on the surface of thin film material

KAUST Repository

Wang, Peng

2017-02-09

Methods are provided for growing a thin film of a nanoscale material. Thin films of nanoscale materials are also provided. The films can be grown with microscale patterning. The method can include vacuum filtration of a solution containing the nanostructured material through a porous substrate. The porous substrate can have a pore size that is comparable to the size of the nanoscale material. By patterning the pores on the surface of the substrate, a film can be grown having the pattern on a surface of the thin film, including on the top surface opposite the substrate. The nanoscale material can be graphene, graphene oxide, reduced graphene oxide, molybdenum disulfide, hexagonal boron nitride, tungsten diselenide, molybdenum trioxide, or clays such as montmorillonite or lapnotie. The porous substrate can be a porous organic or inorganic membrane, a silicon stencil membrane, or similar membrane having pore sizes on the order of microns.

Finite Element Analysis and Optimization for the Multi-stage Deep Drawing of Molybdenum Sheet

International Nuclear Information System (INIS)

Kim, Heung-Kyu; Hong, Seok Kwan; Kang, Jeong Jin; Heo, Young-moo; Lee, Jong-Kil; Jeon, Byung-Hee

2005-01-01

Molybdenum, a bcc refractory metal with a melting point of about 2600 deg. C, has a high heat and electrical conductivity. In addition, it remains strong mechanically at high temperatures as well as at low temperatures. Therefore it is a technologically very important material for the applications operating at high temperatures. However, a multi-stage process is required due to the low drawability for making a deep drawn part from the molybdenum sheet. In this study, a multi-stage deep drawing process for a molybdenum circular cup was designed by combining the drawing with the ironing, which was effective for the low drawability materials. A parametric study by FE analysis for the multi-stage deep drawing was conducted for evaluation of the design variables effect. Based on the FE analysis result, the multi-stage deep drawing process was parameterized by the design variables, and an optimum process design was obtained by the process optimization based on the FE simulation at each stage

Measurement of Actinides in Molybdenum-99 Solution Analytical Procedure

International Nuclear Information System (INIS)

Soderquist, Chuck Z.; Weaver, Jamie L.

2015-01-01

This document is a companion report to a previous report, PNNL 24519, Measurement of Actinides in Molybdenum-99 Solution, A Brief Review of the Literature, August 2015. In this companion report, we report a fast, accurate, newly developed analytical method for measurement of trace alpha-emitting actinide elements in commercial high-activity molybdenum-99 solution. Molybdenum-99 is widely used to produce 99m Tc for medical imaging. Because it is used as a radiopharmaceutical, its purity must be proven to be extremely high, particularly for the alpha emitting actinides. The sample of 99 Mo solution is measured into a vessel (such as a polyethylene centrifuge tube) and acidified with dilute nitric acid. A gadolinium carrier is added (50 µg). Tracers and spikes are added as necessary. Then the solution is made strongly basic with ammonium hydroxide, which causes the gadolinium carrier to precipitate as hydrous Gd(OH) 3 . The precipitate of Gd(OH) 3 carries all of the actinide elements. The suspension of gadolinium hydroxide is then passed through a membrane filter to make a counting mount suitable for direct alpha spectrometry. The high-activity 99 Mo and 99m Tc pass through the membrane filter and are separated from the alpha emitters. The gadolinium hydroxide, carrying any trace actinide elements that might be present in the sample, forms a thin, uniform cake on the surface of the membrane filter. The filter cake is first washed with dilute ammonium hydroxide to push the last traces of molybdate through, then with water. The filter is then mounted on a stainless steel counting disk. Finally, the alpha emitting actinide elements are measured by alpha spectrometry.

Arc-related porphyry molybdenum deposit model: Chapter D in Mineral deposit models for resource assessment

Science.gov (United States)

Taylor, Ryan D.; Hammarstrom, Jane M.; Piatak, Nadine M.; Seal, Robert R.

2012-01-01

This report provides a descriptive model for arc-related porphyry molybdenum deposits. Presented within are geological, geochemical, and mineralogical characteristics that differentiate this deposit type from porphyry copper and alkali-feldspar rhyolite-granite porphyry molybdenum deposits. The U.S. Geological Survey's effort to update existing mineral deposit models spurred this research, which is intended to supplement previously published models for this deposit type that help guide mineral-resource and mineral-environmental assessments.

The solubility of uranium trioxide simulated lung fluid

International Nuclear Information System (INIS)

Kravchiks, T.; Kol, R.; Prager, A.; German, U.; Oved, S.; Laichter, Y.

1997-01-01

Uranium trioxide is an important intermediate compound in the uranium production process. Inhalation of UO 3 aerosols can occur during this process. To assess the radiation dose from the intake of this compound it is necessary to know its transportability class, based on its dissolution rate in lung fluid. The International Commission on Radiological Protection (ICRP) has assigned UO 3 to Inhalation Class W (lung retention half-time of 10 to 100 days). A solubility study of UO 3 in a simulated lung fluid has been carried out using a batch/filter replacement method. Two tests were conducted over a 100-days period, during which 17 samples were collected and analyzed for their dissolved uranium content. The results show that about 40% of the total uranium was dissolved during the first days and nearly all was dissolved during 100 days. Expressed as the fraction of the total uranium remaining undissolved as a function of time, using a non-linear least squares regression fit, it was found that the solubility of UO 3 in simulated lung fluid could be expressed as a combination of two Inactions: about 25% of the UO 3 could be classified as type D (with lung retention half-time of several hours) and about 75% as type W (with half-time of 10-20 days). This classification is in agreement with recent investigations and indicates that UO 3 is more soluble than considered by ICRP. (authors)

Determination of trace amounts of impurities in molybdenum by spark source and glow discharge mass spectrometry

International Nuclear Information System (INIS)

Saito, Morimasa

1994-01-01

For the determination of trace and ultra-trace amounts of impurities in high-purity molybdenum, spark source mass spectrometry and glow discharge mass spectrometry were studied. In spark source mass spectrometry using the metal probe method, the liquid-helium cryogenic pump was used in order to protect the surface of the samples from oxidation. The theoretical relative sensitivity factors (Mo=1) calculated from physical properties were used. The analytical results obtained for molybdenum tablet and high-purity molybdenum were in good agreement with those obtained by other methods (atomic absorption spectrometry and others). In glow discharge mass spectrometry, the relative sensitivity factors were calculated by using the results obtained by spark source mass spectrometry and atomic absorption spectrometry, and this method was applied to the determination of ultra-trace amounts of impurities in ultra high-purity molybdenum and gave the satisfactory results. The detection limits (2σ, n=10) in the integration time of 600 s for U and Th were 0.6 ppb and 0.3 ppb, and the values for Al, Si, Cr, Mn and Cu were in the range of 10 ppb to 0.5 ppb. (author)

Effect of acetic acid on wet patterning of copper/molybdenum thin films in phosphoric acid solution

International Nuclear Information System (INIS)

Seo, Bo.-Hyun; Lee, Sang-Hyuk; Park, In-Sun; Seo, Jong Hyun; Choe, HeeHwan; Jeon, Jae-Hong; Hong, Munpyo; Lee, Yong Uk; Winkler, Joerg

2011-01-01

Copper metallization is a key issue for high performance thin film transistor (TFT) technology. A phosphoric acid based copper etchant is a potentially attractive alternative to the conventional hydrogen peroxide based etchant due to its longer-life expectancy time and higher stability in use. In this paper, it is shown that amount of the acetic acid in the phosphoric based copper etchant plays an important role in controlling the galvanic reaction between the copper and the molybdenum. As the concentration of acetic acid in the phosphoric mixture solution increased from 0 M to 0.4 M, the measured galvanic current density dropped from 32 mA/cm 2 to 26 mA/cm 2 , indicating that the acetic acid induces the lower galvanic reaction between the copper and the molybdenum in the solution. From the XPS analysis, with the addition of the acetic acid, the thickness of the protective MoO 2 passive film covering the molybdenum surface grew and the dissolution rate of the molybdenum thin film decreased. However, the dissolution rate of the copper thin film increased as the concentration of acetic acid in the mixture solution increased.

Effect of acetic acid on wet patterning of copper/molybdenum thin films in phosphoric acid solution

Energy Technology Data Exchange (ETDEWEB)

Seo, Bo.-Hyun; Lee, Sang-Hyuk; Park, In-Sun [Department of Materials Engineering, Korea Aerospace University, Hwajeon, Goyang, Gyonggi-do 412-791 (Korea, Republic of); Seo, Jong Hyun, E-mail: jhseo@kau.ac.kr [Department of Materials Engineering, Korea Aerospace University, Hwajeon, Goyang, Gyonggi-do 412-791 (Korea, Republic of); Choe, HeeHwan; Jeon, Jae-Hong [School of Electronics, Telecommunications and Computer Engineering, Korea Aerospace University, Hwajeon, Goyang, Gyonggi-do 412-791 (Korea, Republic of); Hong, Munpyo [Display and Semiconductor Physics, Korea University (Korea, Republic of); Lee, Yong Uk [PETEC (The Printable Electronics Technology Centre) (United Kingdom); Winkler, Joerg [PLANSEE Metal GmbH, Metallwerk-Plansee-Str. 71A-6600, Reutte (Austria)

2011-08-01

Copper metallization is a key issue for high performance thin film transistor (TFT) technology. A phosphoric acid based copper etchant is a potentially attractive alternative to the conventional hydrogen peroxide based etchant due to its longer-life expectancy time and higher stability in use. In this paper, it is shown that amount of the acetic acid in the phosphoric based copper etchant plays an important role in controlling the galvanic reaction between the copper and the molybdenum. As the concentration of acetic acid in the phosphoric mixture solution increased from 0 M to 0.4 M, the measured galvanic current density dropped from 32 mA/cm{sup 2} to 26 mA/cm{sup 2}, indicating that the acetic acid induces the lower galvanic reaction between the copper and the molybdenum in the solution. From the XPS analysis, with the addition of the acetic acid, the thickness of the protective MoO{sub 2} passive film covering the molybdenum surface grew and the dissolution rate of the molybdenum thin film decreased. However, the dissolution rate of the copper thin film increased as the concentration of acetic acid in the mixture solution increased.

99mTc generator preparation using (n, γ)99Mo produced using natural molybdenum

International Nuclear Information System (INIS)

Kim, Hark Rho; Park, Jin Ho; Lee, Kye Hong

2003-01-01

The Mo-99 is a widely used radioisotope in Korea. To fulfill the demand, we are producing Mo-99 using a specially designed and fabricated rig containing MoO 3 target. We are using natural molybdenum so far. But considering the utilization of the enriched molybdenum to increase the specific activity further, we desire the realization of PZC with (n, γ)Mo-99 as early as possible. To make the generator loading facility, we are in progress of construction work for the related hot cell facilities. (author)

Compton scattering of 145 keV photons from bound electrons of tin and molybdenum

Energy Technology Data Exchange (ETDEWEB)

Ghumman, B S; Acharya, V B; Singh, B [Punjabi Univ., Patiala (India). Dept. of Physics

1981-10-28

Differential cross sections for Compton scattering of 145 keV gamma rays from K-shell electrons of tin and molybdenum are measured at scattering angles in the range 30 to 150/sup 0/. Measurements are made employing NaI(Tl) detectors and a coincidence set up with resolving time approximately equal to 30 ns. The experimental results are compared with the available theoretical data. The total cross section is estimated to be about 0.43 sigmasub(F) for tin and 0.41 sigmasub(F) for molybdenum.

Molybdenum oxide nanocubes: Synthesis and characterizations

Energy Technology Data Exchange (ETDEWEB)

Muthamizh, S.; Suresh, R.; Giribabu, K.; Manigandan, R.; Kumar, S. Praveen; Munusamy, S.; Narayanan, V., E-mail: vnnara@yahoo.co.in [Department of Inorganic Chemistry, University of Madras, Guindy Campus, Chennai -600025 (India); Stephen, A. [Department of Nuclear Physics, University of Madras, Guindy Campus, Chennai-600025 (India)

2015-06-24

Molybdenum oxide nanoparticles were prepared by Solid state synthesis. The MoO{sub 3} nanoparticles were synthesized by using commercially available ammonium heptamolybdate. The XRD pattern reveals that the synthesized MoO{sub 3} has orthorhombic structure. In addition, lattice parameter values were also calculated using XRD data. The Raman analysis confirm the presence of Mo-O in MoO{sub 3} nanoparticles. DRS-UV analysis shows that MoO{sub 3} has a band gap of 2.89 eV. FE-SEM analysis confirms the material morphology in cubes with nano scale.

REACTION PRODUCTS AND CORROSION OF MOLYBDENUM ELECTRODE IN GLASS MELT CONTAINING ANTIMONY OXIDES AND SODIUM SULFATE

Directory of Open Access Journals (Sweden)

JIŘÍ MATĚJ

2012-09-01

Full Text Available The products on the interface of a molybdenum electrode and glass melt were investigated primarily at 1400°C in three model glass melts without ingredients, with 1 % Sb2O3 and with 1 % Sb2O3 and 0.5 % SO3 (wt. %, both under and without load by alternating current. Corrosion of the molybdenum electrode in glass melt without AC load is higher by one order of magnitude if antimony oxides are present. The corrosion continues to increase if sulfate is present in addition to antimony oxides. Isolated antimony droplets largely occur on the electrode-glass melt interface, and numerous droplets are also dissipated in the surrounding glass if only antimony oxides are present in the glass melt. A comparatively continuous layer of antimony occurs on the interface if SO3 is also present, antimony being always in contact with molybdenum sulfide. Almost no antimony droplets are dissipated in the glass melt. The total amount of precipitated antimony also increases. The presence of sulfide on the interface likely facilitates antimony precipitation. The reaction of molybdenum with antimony oxides is inhibited in sites covered by an antimony layer. The composition of sulfide layers formed at 1400°C approximates that of Mo2S3. At 1100°C, the sulfide composition approximates that of MoS4. Corrosion multiplies in the glass melt without additions through the effect of AC current, most molybdenum being separated in the form of metallic particles. Corrosion also increases in the glass melt containing antimony oxides. This is due to increased corrosion in the neighborhood of the separated antimony droplets. This mechanism also results in the loosening of molybdenum particles. The amount of precipitated antimony also increases through the effect of the AC current. AC exerts no appreciable effect on either corrosion, the character of the electrode-glass interface, or antimony precipitation in the glass melt containing SO3.

Boron, cobalt and molybdenum in the knottiness and production on pea (Pisum sativum L.) cv Bolero culture

International Nuclear Information System (INIS)

Oliveira Junior, A.; Teixeira, N.T.; Maluf, C.E.; Campos, M.F. de

1989-01-01

The test carried out to study the effect of Boron, Cobalt and Molybdenum on the knottiness and production of the pea (Pisum sativum L.)cv Bolero culture, in controlled conditions. The results showed that Boron didn't affect the knottiness and it increased the production, while, Cobalt and Molybdenum promoted significant increase in the knottiness and productivity. (author) [pt

Infrared Spectroscopy in the region X-Ray Diffraction and the mineral trioxide aggregate

International Nuclear Information System (INIS)

Barros, C.M.B.; Oliveira, S.V.; Silva, M.C.; Cartaxo, J.M.; Fook, M.V.L.

2011-01-01

In the nineties was introduced into the search field of biomaterials to mineral trioxide aggregate (MTA). It is a derivative of Portland cement with similar chemical properties and was initially developed as a root filling material in dentistry. This material is presented characteristics of mechanical, physical and biological meaningful when applied to biological environment. It was used to search a commercial MTA manipulated with distilled water and propylene glycol in order to verify chemical composition, infrared absorption bands and stages in the samples. The MTA has been characterized by XRF, XRD and FTIR. In X-ray fluorescence was found that the MTA has a characteristic composition of hydraulic cement. Through FTIR MTA mixed with water presents an enlargement in the absorption bands in the region 1467 and 873 cm-1. By means of XRD showed that there is no presence of toxic materials in the majority and secondary phases. (author)

Predicted crystal structures of molybdenum under high pressure

Energy Technology Data Exchange (ETDEWEB)

Wang, Bing; Zhang, Guang Biao [Institute for Computational Materials Science, School of Physics and Electronics, Henan University, Kaifeng 475004 (China); Wang, Yuan Xu, E-mail: wangyx@henu.edu.cn [Institute for Computational Materials Science, School of Physics and Electronics, Henan University, Kaifeng 475004 (China); Guizhou Provincial Key Laboratory of Computational Nano-Material Science, Institute of Applied Physics, Guizhou Normal College, Guiyang 550018 (China)

2013-04-15

Highlights: ► A double-hexagonal close-packed (dhcp) structure of molybdenum is predicted. ► Calculated acoustic velocity confirms the bcc–dhcp phase transition at 660 GPa. ► The valence electrons of dhcp Mo are mostly localized in the interstitial sites. -- Abstract: The high-pressure structures of molybdenum (Mo) at zero temperature have been extensively explored through the newly developed particle swarm optimization (PSO) algorithm on crystal structural prediction. All the experimental and earlier theoretical structures were successfully reproduced in certain pressure ranges, validating our methodology in application to Mo. A double-hexagonal close-packed (dhcp) structure found by Mikhaylushkin et al. (2008) [12] is confirmed by the present PSO calculations. The lattice parameters and physical properties of the dhcp phase were investigated based on first principles calculations. The phase transition occurs only from bcc phase to dhcp phase at 660 GPa and at zero temperature. The calculated acoustic velocities also indicate a transition from the bcc to dhcp phases for Mo. More intriguingly, the calculated density of states (DOS) shows that the dhcp structure remains metallic. The calculated electron density difference (EDD) reveals that its valence electrons are localized in the interstitial regions.

Development and tests of molybdenum armored copper components for MITICA ion source

Science.gov (United States)

Pavei, Mauro; Böswirth, Bernd; Greuner, Henri; Marcuzzi, Diego; Rizzolo, Andrea; Valente, Matteo

2016-02-01

In order to prevent detrimental material erosion of components impinged by back-streaming positive D or H ions in the megavolt ITER injector and concept advancement beam source, a solution based on explosion bonding technique has been identified for producing a 1 mm thick molybdenum armour layer on copper substrate, compatible with ITER requirements. Prototypes have been recently manufactured and tested in the high heat flux test facility Garching Large Divertor Sample Test Facility (GLADIS) to check the capability of the molybdenum-copper interface to withstand several thermal shock cycles at high power density. This paper presents both the numerical fluid-dynamic analyses of the prototypes simulating the test conditions in GLADIS as well as the experimental results.

Development and tests of molybdenum armored copper components for MITICA ion source

International Nuclear Information System (INIS)

Pavei, Mauro; Marcuzzi, Diego; Rizzolo, Andrea; Valente, Matteo; Böswirth, Bernd; Greuner, Henri

2016-01-01

In order to prevent detrimental material erosion of components impinged by back-streaming positive D or H ions in the megavolt ITER injector and concept advancement beam source, a solution based on explosion bonding technique has been identified for producing a 1 mm thick molybdenum armour layer on copper substrate, compatible with ITER requirements. Prototypes have been recently manufactured and tested in the high heat flux test facility Garching Large Divertor Sample Test Facility (GLADIS) to check the capability of the molybdenum-copper interface to withstand several thermal shock cycles at high power density. This paper presents both the numerical fluid-dynamic analyses of the prototypes simulating the test conditions in GLADIS as well as the experimental results

Development and tests of molybdenum armored copper components for MITICA ion source

Energy Technology Data Exchange (ETDEWEB)

Pavei, Mauro, E-mail: mauro.pavei@igi.cnr.it; Marcuzzi, Diego; Rizzolo, Andrea; Valente, Matteo [Consorzio RFX, Corso Stati Uniti, 4, I-35127 Padova (Italy); Böswirth, Bernd; Greuner, Henri [Max-Planck-Institut für Plasmaphysik, Boltzmannstrasse 2, D-85748 Garching (Germany)

2016-02-15

In order to prevent detrimental material erosion of components impinged by back-streaming positive D or H ions in the megavolt ITER injector and concept advancement beam source, a solution based on explosion bonding technique has been identified for producing a 1 mm thick molybdenum armour layer on copper substrate, compatible with ITER requirements. Prototypes have been recently manufactured and tested in the high heat flux test facility Garching Large Divertor Sample Test Facility (GLADIS) to check the capability of the molybdenum-copper interface to withstand several thermal shock cycles at high power density. This paper presents both the numerical fluid-dynamic analyses of the prototypes simulating the test conditions in GLADIS as well as the experimental results.

Molybdenum-containing acidic catalysts to convert cellulosic biomass to glycolic acid

KAUST Repository

Han, Yu; Zhang, Jizhe; Liu, Xin

2014-01-01

Embodiments of the present invention include methods and compositions related to catabolic conversion of cellulosic biomass to glycolic acid using molybdenum-containing acidic catalysts. The invention includes the use of heteropoly and isopoly acids

Nitrogen diffusion in near-surface range of ion doped molybdenum

CERN Document Server

Zamalin, E Y

2001-01-01

The dynamics of change in nitrogen near-the-surface concentration in the Mo ion-alloyed monocrystalline foil is studied through the Auger-electron spectroscopy and the secondary ion mass spectrometry. The implantation dose constituted 5 x 10 sup 1 sup 7 ion/cm sup 2 and the implantation energy equaled 50 and 100 keV. The samples diffusion annealing was performed at the temperature of 800-900 deg C. The evaluation of the nitrogen diffusion coefficient indicates the values by 3-5 orders lesser than the diffusion coefficient in the nitrogen solid-state solution in the molybdenum. At the same time the molybdenum self-diffusion coefficient value is by 3-5 orders lesser as compared to the obtained value. The supposition is made, the the surplus nitrogen relative to the solubility limit is deposited on the radiation defects and in the process of the diffusion annealing it nitrates together with them

Predicting molybdenum toxicity to higher plants: Influence of soil properties

International Nuclear Information System (INIS)

McGrath, S.P.; Mico, C.; Curdy, R.; Zhao, F.J.

2010-01-01

The effect of soil properties on the toxicity of molybdenum (Mo) to four plant species was investigated. Soil organic carbon or ammonium-oxalate extractable Fe oxides were found to be the best predictors of the 50% effective dose (ED 50 ) of Mo in different soils, explaining > 65% of the variance in ED 50 for four species except for ryegrass (26-38%). Molybdenum concentrations in soil solution and consequently plant uptake were increased when soil pH was artificially raised because sorption of Mo to amorphous oxides is greatly reduced at high pH. The addition of sulphate significantly decreased Mo uptake by oilseed rape. For risk assessment, we suggest that Mo toxicity values for plants should be normalised using soil amorphous iron oxide concentrations. - Amorphous iron oxides or organic carbon were found to be the best predictors of the toxicity threshold values of Mo to higher plants on different soils.

Effects of exposure to high-temperature helium containing oxygen on the mechanical properties of molybdenum and TZM-Mo alloy at room temperature

International Nuclear Information System (INIS)

Noda, T.; Okada, M.; Watanabe, R.

1980-01-01

The effects of exposure to helium containing oxygen of 0.1-115 vpm at 1000 0 C on the mechanical properties of molybdenum and TZM-Mo alloy at room temperature were studied. The stress-relieved molybdenum specimen which was not recrystallized at test temperature showed the ductility after exposure to helium containing oxygen. The recrystallized molybdenum and TZM lost ductility after exposure to helium containing oxygen of 0.1-13 vpm in a few hours. The embrittlement of molybdenum was considered to be due to the grain boundary weakening. Molybdenum to which carbon was added seemed to hinder the grain boundary weakening by the oxygen contamination. Both stress-relieved and recrystallized TZM specimens picked up oxygen linearly with time of exposure to helium. The increase in oxygen content of TZM, which was considered to be caused by the internal oxidation of titanium and zirconium, results in the embrittlement of TZM. (orig.)

Moessbauer study of defects in molybdenum and chromium irradiated with ions

International Nuclear Information System (INIS)

Troyan, V.A.; Bogdanov, V.V.; Ivanyushkin, E.M.; Pen'kov, Yu.P.

1980-01-01

Effects of ion irradiation of monocrystalline molybdenum and polycrystalline chromium with Co-57 impurity were studied by Moessbauer effect. Molybdenum specimens were irradiated by He + ions at accelerators with 40 keV energy. Chromium specimens were irradiated by hydrogen ions with 1.2 MeV energy up to integral 2x10 17 -2x10 19 ion/cm 2 doses. It is shown, that defect introduction into the source matrix by irradiation results in change of gamma-resonance line form and effect value. The observed effects of defect influence on spectrum parameters are discussed. It is concluded, that study of Moessbauer spectra parameters of diluted Co-57 solutions in matrices of different metals permits to determine dynamics of movement of impurity atoms and defects in metals irradiated with ions [ru

Influence of plastic deformation on nitriding of a molybdenum-hafnium alloy

International Nuclear Information System (INIS)

Lakhtin, Yu.M.; Kogan, Ya.D.; Shashkov, D.P.; Likhacheva, T.E.

1982-01-01

The influence of a preliminary plastic strain on the structure and properties of molybdenum alloy with 0.2 wt.% Hf upon nitriding in the ammonia medium at 900-1200 deg C during 1-6 h is investigated. The study of microhardness distribution across the nitrided layer thickness has shown that with increase of the degree of preliminary plastic strain up to 50 % the nitrided layer hardness decreases and with further reduction growth up to 90 % - increases. Nitriding sharply (hundred times) increases wear resistance of molybdenum alloy with hafnium addition. At the reduction degree 25 % the wear resistance is less than at other values of percentage reduction in area owing to the minimum thickness of the nitride zone. The alloy strained before nitriding by 25 % has shown the best results during heat resistance testing

Determination of molybdenum and selenium in bioenvironmental samples using neutron activation analysis

International Nuclear Information System (INIS)

Abu-Samra, A.; Morris, J.S.; Koirtyohann, S.R.; Vogt, J.R.

1974-01-01

Because of the increasing interest as to their roles in biological systems, a procedure has been developed by which molybdenum and selenium can be determined at nanogram levels in these types of samples. Results from the analysis of orchard leaves and bovine liver are presented. The samples are packaged in pre-cleaned quartz vials prepared from GE-204 tubing. If both selenium and molybdenum are to be determined, the samples are irradiated for 40 or more hours at a thermal neutron flux of 8 x 10 13 n cm -2 sec -1 . After the samples have decayed for approximately 48 hours the vials are unpackaged, cleaned in aqua-regia, and broken. The irradiation period can be reduced to 24 hours if molybdenum is to be determined individually or if the selenium content is known to be 1 microgram or more. The sample is digested with carriers and the selenium is then distilled as a volatile selenium halide. Elemental selenium is precipitated by reduction with SO 2 produced through the protonation of the hydrogen sulfite ion and subsequent decomposition of the resulting sulfurous acid. The 401 keV summation peak of 75 Se is normally used for quantitative determination. The chemical yield is determined by drying and weighing the elemental selenium

Effect of dietary molybdenum and sulphur on the copper status of ...

African Journals Online (AJOL)

in all groups receiving supplementary Mo. A dietary supplement of 70 mg Mo for a restricted period is ... Keywords: Sheep nutrition, copper toxicity, molybdenum toxicity, sulphur. ..... observation supports the suggestion by Dick, et af. (1975).

Sulfidation of alumina-supported iron and iron-molybdenum oxide catalysts

NARCIS (Netherlands)

Ramselaar, W.L.T.M.; Crajé, M.W.J.; Hadders, R.H.; Gerkema, E.; Beer, de V.H.J.; Kraan, van der A.M.

1990-01-01

The transition of alumina-supported iron and iron-molybdenum catalysts from the oxidic precursor to the sulfided catalysts was systematically studied by means of in-situ Mössbauer spectroscopy at room temperature. This enabled the adjudgement of various sulfidic phases in the sulfided catalysts. The

DFT Study of the Molybdenum-Catalyzed Deoxydehydration of Vicinal Diols

DEFF Research Database (Denmark)

Lupp, Daniel; Christensen, Niels Johan; Dethlefsen, Johannes Rytter

2015-01-01

, and extrusion of the alkene. We have compared the proposed pathway with several alternatives, and the results have been corroborated by comparison with the molybdenum- catalyzed sulfoxide reduction recently published by Sanz et al. and with experimental observations for the DODH itself. Improved understanding...

Measurement of Actinides in Molybdenum-99 Solution Analytical Procedure

Energy Technology Data Exchange (ETDEWEB)

Soderquist, Chuck Z. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Weaver, Jamie L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-11-01

This document is a companion report to a previous report, PNNL 24519, Measurement of Actinides in Molybdenum-99 Solution, A Brief Review of the Literature, August 2015. In this companion report, we report a fast, accurate, newly developed analytical method for measurement of trace alpha-emitting actinide elements in commercial high-activity molybdenum-99 solution. Molybdenum-99 is widely used to produce ^99mTc for medical imaging. Because it is used as a radiopharmaceutical, its purity must be proven to be extremely high, particularly for the alpha emitting actinides. The sample of ⁹⁹Mo solution is measured into a vessel (such as a polyethylene centrifuge tube) and acidified with dilute nitric acid. A gadolinium carrier is added (50 µg). Tracers and spikes are added as necessary. Then the solution is made strongly basic with ammonium hydroxide, which causes the gadolinium carrier to precipitate as hydrous Gd(OH)₃. The precipitate of Gd(OH)₃ carries all of the actinide elements. The suspension of gadolinium hydroxide is then passed through a membrane filter to make a counting mount suitable for direct alpha spectrometry. The high-activity ⁹⁹Mo and ^99mTc pass through the membrane filter and are separated from the alpha emitters. The gadolinium hydroxide, carrying any trace actinide elements that might be present in the sample, forms a thin, uniform cake on the surface of the membrane filter. The filter cake is first washed with dilute ammonium hydroxide to push the last traces of molybdate through, then with water. The filter is then mounted on a stainless steel counting disk. Finally, the alpha emitting actinide elements are measured by alpha spectrometry.

Growth of molybdenum disulphide using iodine as transport material

Indian Academy of Sciences (India)

In the present paper an attempt has been made to describe the chemical vapor transport (CVT) technique used for the growth of molybdenum disulphide (MoS2) single crystals. Iodine (I2) is used as transporting material for this purpose. The energy dispersive analysis by X-ray (EDAX) confirmed the stoichiometry of the ...

Simultaneous spectrophotometric determination of tungsten and molybdenum with dithiol

International Nuclear Information System (INIS)

Navale, A.S.

1987-01-01

Toluene-3,4-dithiol is a very sensitive reagent for the spectrophotometric determination of tungsten and molybdenum. Since the absorption spectra of the dithiol complexes of these two elements overlap, a separation of the two elements is carried out. This leads to time consuming extraction procedures. Measuring the absorption of the mixed complexes at two wavelengths and solving a set of simultaneous equations is also not favorable because a lot of time and effort is required for solving the simultaneous equations for each sample. A faster and simpler method is described here for the simultaneous determination of the two elements. The method is based on measurement of absorbance of the mixed complexes at three pre-selected wavelengths and simple calculations involving the absorbance differences. The criteria for selecting the three wavelengths and the theory are described. Application of the method for the determination of tungsten and molybdenum in ore samples is presented. The method is applicable to any similar system consisting of two interfering components. 4 figures, 2 tables, 6 refs. (author)