Gatland, Ian R.
2002-01-01
Proposes a ray tracing approach to thin lens analysis based on a vector form of Snell's law for paraxial rays as an alternative to the usual approach in introductory physics courses. The ray tracing approach accommodates skew rays and thus provides a complete analysis. (Author/KHR)
Lam, Wai Sze Tiffany
Optical components made of anisotropic materials, such as crystal polarizers and crystal waveplates, are widely used in many complex optical system, such as display systems, microlithography, biomedical imaging and many other optical systems, and induce more complex aberrations than optical components made of isotropic materials. The goal of this dissertation is to accurately simulate the performance of optical systems with anisotropic materials using polarization ray trace. This work extends the polarization ray tracing calculus to incorporate ray tracing through anisotropic materials, including uniaxial, biaxial and optically active materials. The 3D polarization ray tracing calculus is an invaluable tool for analyzing polarization properties of an optical system. The 3x3 polarization ray tracing P matrix developed for anisotropic ray trace assists tracking the 3D polarization transformations along a ray path with series of surfaces in an optical system. To better represent the anisotropic light-matter interactions, the definition of the P matrix is generalized to incorporate not only the polarization change at a refraction/reflection interface, but also the induced optical phase accumulation as light propagates through the anisotropic medium. This enables realistic modeling of crystalline polarization elements, such as crystal waveplates and crystal polarizers. The wavefront and polarization aberrations of these anisotropic components are more complex than those of isotropic optical components and can be evaluated from the resultant P matrix for each eigen-wavefront as well as for the overall image. One incident ray refracting or reflecting into an anisotropic medium produces two eigenpolarizations or eigenmodes propagating in different directions. The associated ray parameters of these modes necessary for the anisotropic ray trace are described in Chapter 2. The algorithms to calculate the P matrix from these ray parameters are described in Chapter 3 for
Interactive Ray Tracing for Virtual TV Studio Applications
Philipp Slusallek
2005-12-01
Full Text Available In the last years, the well known ray tracing algorithm gained new popularity with the introduction of interactive ray tracing methods. The high modularity and the ability to produce highly realistic images make ray tracing an attractive alternative to raster graphics hardware.Interactive ray tracing also proved its potential in the field of Mixed Reality rendering and provides novel methods for seamless integration of real and virtual content. Actor insertion methods, a subdomain of Mixed Reality and closely related to virtual television studio techniques, can use ray tracing for achieving high output quality in conjunction with appropriate visual cues like shadows and reflections at interactive frame rates.In this paper, we show how interactive ray tracing techniques can provide new ways of implementing future virtual studio applications.
IONORT: IONOsphere Ray-Tracing
Bianchi, C.; Settimi, A; Azzarone, A.
2010-01-01
Il pacchetto applicativo “IONORT” per il calcolo del ray-tracing può essere utilizzato dagli utenti che impiegano il sistema operativo Windows. È un programma la cui interfaccia grafica con l’utente è realizzata in MATLAB. In realtà, il programma lancia un eseguibile che integra il sistema d’equazioni differenziali scritto in linguaggio Fortran e ne importa l’output nel programma MATLAB, il quale genera i grafici e altre informazioni sul raggio. A completamento di questa premessa va detto ...
Fast Ray Tracing NURBS Surfaces
秦开怀; 龚明伦; 等
1996-01-01
In this paper,a new algorithm wit extrapolation process for computing the ray/surface intersection is presented.Also,a ray is defined to be the intersection of two planes,which are non-orthogonal in general,in such a way that the number of multiplication operations is reduced.In the preprocessing step,NURBS surfaces are subdivded adaptively into rational Bezier patches.Parallelepipeds are used to enclose the respective patches as tightly as possible Therefore,for each ray that hits the enclosure(i.e.,parallelepiped)of a patch the intersection points with the parallelepiped's faces can be used to yield a good starting point for the following iteration.The improved Newton iteration with extrapolation process saves CPU time by reducing the number of iteration steps.The intersection scheme is facter than previous methods for which published performance data allow reliable comparison.The method may also be used to speed up tracing the intersection of two parametric surfaces and oter operations that need Newton iteration.
RAY TRACING IMPLEMENTATION IN JAVA PROGRAMMING LANGUAGE
Aybars UĞUR
2002-01-01
Full Text Available In this paper realism in computer graphics and components providing realism are discussed at first. It is mentioned about illumination models, surface rendering methods and light sources for this aim. After that, ray tracing which is a technique for creating two dimensional image of a three-dimensional virtual environment is explained briefly. A simple ray tracing algorithm was given. "SahneIzle" which is a ray tracing program implemented in Java programming language which can be used on the internet is introduced. As a result, importance of network-centric ray tracing software is discussed.
Reverse ray tracing for transformation optics.
Hu, Chia-Yu; Lin, Chun-Hung
2015-06-29
Ray tracing is an important technique for predicting optical system performance. In the field of transformation optics, the Hamiltonian equations of motion for ray tracing are well known. The numerical solutions to the Hamiltonian equations of motion are affected by the complexities of the inhomogeneous and anisotropic indices of the optical device. Based on our knowledge, no previous work has been conducted on ray tracing for transformation optics with extreme inhomogeneity and anisotropicity. In this study, we present the use of 3D reverse ray tracing in transformation optics. The reverse ray tracing is derived from Fermat's principle based on a sweeping method instead of finding the full solution to ordinary differential equations. The sweeping method is employed to obtain the eikonal function. The wave vectors are then obtained from the gradient of that eikonal function map in the transformed space to acquire the illuminance. Because only the rays in the points of interest have to be traced, the reverse ray tracing provides an efficient approach to investigate the illuminance of a system. This approach is useful in any form of transformation optics where the material property tensor is a symmetric positive definite matrix. The performance and analysis of three transformation optics with inhomogeneous and anisotropic indices are explored. The ray trajectories and illuminances in these demonstration cases are successfully solved by the proposed reverse ray tracing method.
Validation of Ray Tracing Code Refraction Effects
Heath, Stephanie L.; McAninch, Gerry L.; Smith, Charles D.; Conner, David A.
2008-01-01
NASA's current predictive capabilities using the ray tracing program (RTP) are validated using helicopter noise data taken at Eglin Air Force Base in 2007. By including refractive propagation effects due to wind and temperature, the ray tracing code is able to explain large variations in the data observed during the flight test.
The Alba ray tracing code: ART
Nicolas, Josep; Barla, Alessandro; Juanhuix, Jordi
2013-09-01
The Alba ray tracing code (ART) is a suite of Matlab functions and tools for the ray tracing simulation of x-ray beamlines. The code is structured in different layers, which allow its usage as part of optimization routines as well as an easy control from a graphical user interface. Additional tools for slope error handling and for grating efficiency calculations are also included. Generic characteristics of ART include the accumulation of rays to improve statistics without memory limitations, and still providing normalized values of flux and resolution in physically meaningful units.
Backward ray tracing for ultrasonic imaging
Breeuwer, R.
1990-01-01
Focused ultrasonic beams frequently pass one or more media interfaces, strongly affecting the ultrasonic beamshape and focusing. A computer program, based on backward ray tracing was developed to compute the shape of a corrected focusing mirror. This shape is verified with another program; then the
Backward ray tracing for ultrasonic imaging
Breeuwer, R.
1990-01-01
Focused ultrasonic beams frequently pass one or more media interfaces, strongly affecting the ultrasonic beamshape and focusing. A computer program, based on backward ray tracing was developed to compute the shape of a corrected focusing mirror. This shape is verified with another program; then the
OSPRay - A CPU Ray Tracing Framework for Scientific Visualization.
Wald, I; Johnson, G P; Amstutz, J; Brownlee, C; Knoll, A; Jeffers, J; Gunther, J; Navratil, P
2017-01-01
Scientific data is continually increasing in complexity, variety and size, making efficient visualization and specifically rendering an ongoing challenge. Traditional rasterization-based visualization approaches encounter performance and quality limitations, particularly in HPC environments without dedicated rendering hardware. In this paper, we present OSPRay, a turn-key CPU ray tracing framework oriented towards production-use scientific visualization which can utilize varying SIMD widths and multiple device backends found across diverse HPC resources. This framework provides a high-quality, efficient CPU-based solution for typical visualization workloads, which has already been integrated into several prevalent visualization packages. We show that this system delivers the performance, high-level API simplicity, and modular device support needed to provide a compelling new rendering framework for implementing efficient scientific visualization workflows.
RAY TRACING RENDER MENGGUNAKAN FRAGMENT ANTI ALIASING
Febriliyan Samopa
2008-07-01
Full Text Available Normal 0 false false false IN X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Rendering is generating surface and three-dimensional effects on an object displayed on a monitor screen. Ray tracing as a rendering method that traces ray for each image pixel has a drawback, that is, aliasing (jaggies effect. There are some methods for executing anti aliasing. One of those methods is OGSS (Ordered Grid Super Sampling. OGSS is able to perform aliasing well. However, this method requires more computation time since sampling of all pixels in the image will be increased. Fragment Anti Aliasing (FAA is a new alternative method that can cope with the drawback. FAA will check the image when performing rendering to a scene. Jaggies effect is only happened at curve and gradient object. Therefore, only this part of object that will experience sampling magnification. After this sampling magnification and the pixel values are computed, then downsample is performed to retrieve the original pixel values. Experimental results show that the software can implement ray tracing well in order to form images, and it can implement FAA and OGSS technique to perform anti aliasing. In general, rendering using FAA is faster than using OGSS
IL RAY-TRACING NELLA IONOSFERA
Azzarone, A.; Bianchi, C.; Settimi, A
2010-01-01
Il pacchetto applicativo “IONORT” per il calcolo del ray-tracing può essere utilizzato dagli utenti che impiegano il sistema operativo Windows. È un programma la cui interfaccia grafica con l’utente è realizzata in MATLAB. In realtà, il programma lancia un eseguibile che integra il sistema d’equazioni differenziali scritto in linguaggio Fortran e ne importa l’output nel programma MATLAB, il quale genera i grafici e altre informazioni sul raggio. A completamento di questa premessa va detto che...
IONORT: IONOsphere Ray-Tracing - Ray-tracing program in ionospheric magnetoplasma
Bianchi, Cesidio; Settimi, Alessandro; Azzarone, Adriano
2010-01-01
The application package "IONORT" for the calculation of ray-tracing can be used by customers using the Windows operating system. It is a program whose interface with the user is created in MATLAB. In fact, the program launches an executable that integrates the system of differential equations written in Fortran and importing the output in the MATLAB program, which generates graphics and other information on the ray. This work is inspired mainly by the program of Jones and Stephenson, widespre...
RayTrace: A Simplified Ray Tracing Software for use in AutoCad
Reimann, Gregers Peter; Tang, C.K.
2005-01-01
A design aid tool for testing and development of daylighting systems was developed. A simplified ray tracing software was programmed in Lisp for AutoCad. Only fully specularly reflective, fully transparent and fully absorbant surfaces can be defined in the software. The software is therefore best...
RayTrace: A Simplified Ray Tracing Software for use in AutoCad
Reimann, Gregers Peter; Tang, C.K.
2005-01-01
A design aid tool for testing and development of daylighting systems was developed. A simplified ray tracing software was programmed in Lisp for AutoCad. Only fully specularly reflective, fully transparent and fully absorbant surfaces can be defined in the software. The software is therefore best...
Development of ray tracing visualization program by Monte Carlo method
Higuchi, Kenji; Otani, Takayuki [Japan Atomic Energy Research Inst., Tokyo (Japan); Hasegawa, Yukihiro
1997-09-01
Ray tracing algorithm is a powerful method to synthesize three dimensional computer graphics. In conventional ray tracing algorithms, a view point is used as a starting point of ray tracing, from which the rays are tracked up to the light sources through center points of pixels on the view screen to calculate the intensities of the pixels. This manner, however, makes it difficult to define the configuration of light source as well as to strictly simulate the reflections of the rays. To resolve these problems, we have developed a new ray tracing means which traces rays from a light source, not from a view point, with use of Monte Carlo method which is widely applied in nuclear fields. Moreover, we adopt the variance reduction techniques to the program with use of the specialized machine (Monte-4) for particle transport Monte Carlo so that the computational time could be successfully reduced. (author)
Development of ray tracing visualization program by Monte Carlo method
Higuchi, Kenji; Otani, Takayuki [Japan Atomic Energy Research Inst., Tokyo (Japan); Hasegawa, Yukihiro
1997-09-01
Ray tracing algorithm is a powerful method to synthesize three dimensional computer graphics. In conventional ray tracing algorithms, a view point is used as a starting point of ray tracing, from which the rays are tracked up to the light sources through center points of pixels on the view screen to calculate the intensities of the pixels. This manner, however, makes it difficult to define the configuration of light source as well as to strictly simulate the reflections of the rays. To resolve these problems, we have developed a new ray tracing means which traces rays from a light source, not from a view point, with use of Monte Carlo method which is widely applied in nuclear fields. Moreover, we adopt the variance reduction techniques to the program with use of the specialized machine (Monte-4) for particle transport Monte Carlo so that the computational time could be successfully reduced. (author)
Powerful scriptable ray tracing package xrt
Klementiev, Konstantin; Chernikov, Roman
2014-09-01
We present an open source python based ray tracing tool that offers several useful features in graphical presentation, material properties, advanced calculations of synchrotron sources, implementation of diffractive and refractive elements, complex (also closed) surfaces and multiprocessing. The package has many usage examples which are supplied together with the code and visualized on its web page. We exemplify the present version by modeling (i) a curved crystal analyzer, (ii) a quarter wave plate, (iii) Bragg-Fresnel optics and (iv) multiple reflective and non-sequential optics (polycapillary). The present version implements the use of OpenCL framework that executes calculations on both CPUs and GPUs. Currently, the calculations of an undulator source on a GPU show a gain of about two orders of magnitude in computing time. The development version is successful in modelling the wavefront propagation. Two examples of diffraction on a plane mirror and a plane blazed grating are given for a beam with a finite energy band.
Three-dimensional polarization ray-tracing calculus II: retardance.
Yun, Garam; McClain, Stephen C; Chipman, Russell A
2011-06-20
The concept of retardance is critically analyzed for ray paths through optical systems described by a three-by-three polarization ray-tracing matrix. Algorithms are presented to separate the effects of retardance from geometric transformations. The geometric transformation described by a "parallel transport matrix" characterizes nonpolarizing propagation through an optical system, and also provides a proper relationship between sets of local coordinates along the ray path. The proper retardance is calculated by removing this geometric transformation from the three-by-three polarization ray-tracing matrix. Two rays with different ray paths through an optical system can have the same polarization ray-tracing matrix but different retardances. The retardance and diattenuation of an aluminum-coated three fold-mirror system are analyzed as an example.
Simplification of vector ray tracing by the groove function.
Hu, Zhongwen; Liu, Zuping; Wang, Qiuping
2005-01-01
Tracing rays through arbitrary diffraction gratings (including holographic gratings of the second generation fabricated on a curved substrate) by the vector form is somewhat complicated. Vector ray tracing utilizes the local groove density, the calculation of which highly depends on how the grooves are generated. Characterizing a grating by its groove function, available for almost arbitrary gratings, is much simpler than doing so by its groove density, essentially being a vector. Applying the concept of Riemann geometry, we give an expression of the groove density by the groove function. The groove function description of a grating can thus be incorporated into vector ray tracing, which is beneficial especially at the design stage. A unified explicit grating ray-tracing formalism is given as well.
IONORT: IONOsphere Ray-Tracing - Ray-tracing program in ionospheric magnetoplasma
Bianchi, Cesidio; Azzarone, Adriano
2010-01-01
The application package "IONORT" for the calculation of ray-tracing can be used by customers using the Windows operating system. It is a program whose interface with the user is created in MATLAB. In fact, the program launches an executable that integrates the system of differential equations written in Fortran and imports the output in the MATLAB program, which generates graphics and other information on the ray. This work is inspired mainly by the program of Jones and Stephenson, widespread in the scientific community that is interested in radio propagation via the ionosphere. The program is written in FORTRAN 77, a mainframe CDC-3800. The code itself, as well as being very elegant, is highly efficient and provides the basis for many programs now in use mainly in the Coordinate Registration (CR) of Over The Horizon (OTH) radar. The input and output of this program require devices no longer in use for several decades and there are no compilers that accept instructions written for that type of mainframe. For ...
Masmoudi, Nabil
2014-01-01
We present an approximate, but efficient and sufficiently accurate P-wave ray tracing and dynamic ray tracing procedure for 3D inhomogeneous, weakly orthorhombic media with varying orientation of symmetry planes. In contrast to commonly used approaches, the orthorhombic symmetry is preserved at any point of the model. The model is described by six weak-anisotropy parameters and three Euler angles, which may vary arbitrarily, but smoothly, throughout the model. We use the procedure for the calculation of rays and corresponding two-point traveltimes in a VSP experiment in a part of the BP benchmark model generalized to orthorhombic symmetry.
Benthin, Carsten; Wald, Ingo; Woop, Sven; Ernst, Manfred; Mark, William R
2012-09-01
Wide-SIMD hardware is power and area efficient, but it is challenging to efficiently map ray tracing algorithms to such hardware especially when the rays are incoherent. The two most commonly used schemes are either packet tracing, or relying on a separate traversal stack for each SIMD lane. Both work great for coherent rays, but suffer when rays are incoherent: The former experiences a dramatic loss of SIMD utilization once rays diverge; the latter requires a large local storage, and generates multiple incoherent streams of memory accesses that present challenges for the memory system. In this paper, we introduce a single-ray tracing scheme for incoherent rays that uses just one traversal stack on 16-wide SIMD hardware. It uses a bounding-volume hierarchy with a branching factor of four as the acceleration structure, exploits four-wide SIMD in each box and primitive intersection test, and uses 16-wide SIMD by always performing four such node or primitive tests in parallel. We then extend this scheme to a hybrid tracing scheme that automatically adapts to varying ray coherence by starting out with a 16-wide packet scheme and switching to the new single-ray scheme as soon as rays diverge. We show that on the Intel Many Integrated Core architecture this hybrid scheme consistently, and over a wide range of scenes and ray distributions, outperforms both packet and single-ray tracing.
Implementation of Refined Ray Tracing inside a Space Module
Balamati Choudhury
2012-08-01
Full Text Available Modern space modules are susceptible to EM radiation from both external and internal sources within the space module. Since the EM waves for various operations are frequently in the high-frequency domain, asymptotic raytheoretic methods are often the most optimal choice for deterministic EM field analysis. In this work, surface modeling of a typical manned space module is done by hybridizing a finite segment of right circular cylinder and a general paraboloid of revolution (GPOR frustum. A transmitting source is placed inside the space module and test rays are launched from the transmitter. The rays are allowed to propagate inside the cavity. Unlike the available ray-tracing package, that use numerical search methods, a quasi-analytical ray-propagation model is developed to obtain the ray-path details inside the cavity which involves the ray-launching, ray-bunching, and an adaptive cube for ray-reception.
Ray Tracing RF Field Prediction: An Unforgiving Validation
E. M. Vitucci
2015-01-01
Full Text Available The prediction of RF coverage in urban environments is now commonly considered a solved problem with tens of models proposed in the literature showing good performance against measurements. Among these, ray tracing is regarded as one of the most accurate ones available. In the present work, however, we show that a great deal of work is still needed to make ray tracing really unleash its potential in practical use. A very extensive validation of a state-of-the-art 3D ray tracing model is carried out through comparison with measurements in one of the most challenging environments: the city of San Francisco. Although the comparison is based on RF cellular coverage at 850 and 1900 MHz, a widely studied territory, very relevant sources of error and inaccuracy are identified in several cases along with possible solutions.
GPU-based Ray Tracing of Dynamic Scenes
Christopher Lux
2010-08-01
Full Text Available Interactive ray tracing of non-trivial scenes is just becoming feasible on single graphics processing units (GPU. Recent work in this area focuses on building effective acceleration structures, which work well under the constraints of current GPUs. Most approaches are targeted at static scenes and only allow navigation in the virtual scene. So far support for dynamic scenes has not been considered for GPU implementations. We have developed a GPU-based ray tracing system for dynamic scenes consisting of a set of individual objects. Each object may independently move around, but its geometry and topology are static.
Parallel Ray Tracing Using the Message Passing Interface
2007-09-01
efficiency of 97.9% and a normalized ray-tracing rate of 6.95 ?106 rays ? surfaces/(s ? processor) in a system with 22 planar surfaces, two paraboloid ...with 22 planar surfaces, two paraboloid reflectors, and one hyperboloid refractor. The need for a load-balancing software was obviated by the use of a...specified for each type of optical surface—planar, spherical, paraboloid , hyperboloid, aspheric—and whether it applies for reflection or refraction. The
Real time ray tracing of skeletal implicit surfaces
Rouiller, Olivier; Bærentzen, Jakob Andreas
Modeling and rendering in real time is usually done via rasterization of polygonal meshes. We present a method to model with skeletal implicit surfaces and an algorithm to ray trace these surfaces in real time in the GPU. Our skeletal representation of the surfaces allows to create smooth models...
Ray Tracing Modelling of Reflector for Vertical Bifacial Panel
Jakobsen, Michael Linde; Thorsteinsson, Sune; Poulsen, Peter Behrensdorff
2016-01-01
Bifacial solar panels have recently become a new attractive building block for PV systems. In this work we propose a reflector system for a vertical bifacial panel, and use ray tracing modelling to model the performance. Particularly, we investigate the impact of the reflector volume being filled...
Ray tracing and refraction in the modified US1976 atmosphere
van der Werf, SY
2003-01-01
A new and flexible ray-tracing procedure for calculating astronomical refraction is outlined and applied to the US1976 standard atmosphere. This atmosphere is generalized to allow for a free choice of the temperature and pressure at sea level, and in this form it has been named the modified US1976
Simplifying numerical ray tracing for characterization of optical systems.
Gagnon, Yakir Luc; Speiser, Daniel I; Johnsen, Sönke
2014-07-20
Ray tracing, a computational method for tracing the trajectories of rays of light through matter, is often used to characterize mechanical or biological visual systems with aberrations that are larger than the effect of diffraction inherent in the system. For example, ray tracing may be used to calculate geometric point spread functions (PSFs), which describe the image of a point source after it passes through an optical system. Calculating a geometric PSF is useful because it gives an estimate of the detail and quality of the image formed by a given optical system. However, when using ray tracing to calculate a PSF, the accuracy of the estimated PSF directly depends on the number of discrete rays used in the calculation; higher accuracies may require more computational power. Furthermore, adding optical components to a modeled system will increase its complexity and require critical modifications so that the model will describe the system correctly, sometimes necessitating a completely new model. Here, we address these challenges by developing a method that represents rays of light as a continuous function that depends on the light's initial direction. By utilizing Chebyshev approximations (via the chebfun toolbox in MATLAB) for the implementation of this method, we greatly simplified the calculations for the location and direction of the rays. This method provides high precision and fast calculation speeds that allow the characterization of any symmetrical optical system (with a centered point source) in an analytical-like manner. Next, we demonstrate our methods by showing how they can easily calculate PSFs for complicated optical systems that contain multiple refractive and/or reflective interfaces.
Improved algorithm of ray tracing in ICF cryogenic targets
Zhang, Rui; Yang, Yongying; Ling, Tong; Jiang, Jiabin
2016-10-01
The high precision ray tracing inside inertial confinement fusion (ICF) cryogenic targets plays an important role in the reconstruction of the three-dimensional density distribution by algebraic reconstruction technique (ART) algorithm. The traditional Runge-Kutta methods, which is restricted by the precision of the grid division and the step size of ray tracing, cannot make an accurate calculation in the case of refractive index saltation. In this paper, we propose an improved algorithm of ray tracing based on the Runge-Kutta methods and Snell's law of refraction to achieve high tracing precision. On the boundary of refractive index, we apply Snell's law of refraction and contact point search algorithm to ensure accuracy of the simulation. Inside the cryogenic target, the combination of the Runge-Kutta methods and self-adaptive step algorithm are employed for computation. The original refractive index data, which is used to mesh the target, can be obtained by experimental measurement or priori refractive index distribution function. A finite differential method is performed to calculate the refractive index gradient of mesh nodes, and the distance weighted average interpolation methods is utilized to obtain refractive index and gradient of each point in space. In the simulation, we take ideal ICF target, Luneberg lens and Graded index rod as simulation model to calculate the spot diagram and wavefront map. Compared the simulation results to Zemax, it manifests that the improved algorithm of ray tracing based on the fourth-order Runge-Kutta methods and Snell's law of refraction exhibits high accuracy. The relative error of the spot diagram is 0.2%, and the peak-to-valley (PV) error and the root-mean-square (RMS) error of the wavefront map is less than λ/35 and λ/100, correspondingly.
A Fast Ray-Tracing Using Bounding Spheres and Frustum Rays for Dynamic Scene Rendering
Suzuki, Ken-Ichi; Kaeriyama, Yoshiyuki; Komatsu, Kazuhiko; Egawa, Ryusuke; Ohba, Nobuyuki; Kobayashi, Hiroaki
Ray tracing is one of the most popular techniques for generating photo-realistic images. Extensive research and development work has made interactive static scene rendering realistic. This paper deals with interactive dynamic scene rendering in which not only the eye point but also the objects in the scene change their 3D locations every frame. In order to realize interactive dynamic scene rendering, RTRPS (Ray Tracing based on Ray Plane and Bounding Sphere), which utilizes the coherency in rays, objects, and grouped-rays, is introduced. RTRPS uses bounding spheres as the spatial data structure which utilizes the coherency in objects. By using bounding spheres, RTRPS can ignore the rotation of moving objects within a sphere, and shorten the update time between frames. RTRPS utilizes the coherency in rays by merging rays into a ray-plane, assuming that the secondary rays and shadow rays are shot through an aligned grid. Since a pair of ray-planes shares an original ray, the intersection for the ray can be completed using the coherency in the ray-planes. Because of the three kinds of coherency, RTRPS can significantly reduce the number of intersection tests for ray tracing. Further acceleration techniques for ray-plane-sphere and ray-triangle intersection are also presented. A parallel projection technique converts a 3D vector inner product operation into a 2D operation and reduces the number of floating point operations. Techniques based on frustum culling and binary-tree structured ray-planes optimize the order of intersection tests between ray-planes and a sphere, resulting in 50% to 90% reduction of intersection tests. Two ray-triangle intersection techniques are also introduced, which are effective when a large number of rays are packed into a ray-plane. Our performance evaluations indicate that RTRPS gives 13 to 392 times speed up in comparison with a ray tracing algorithm without organized rays and spheres. We found out that RTRPS also provides competitive
Ray tracing reconstruction investigation for C-arm tomosynthesis
Malalla, Nuhad A. Y.; Chen, Ying
2016-04-01
C-arm tomosynthesis is a three dimensional imaging technique. Both x-ray source and the detector are mounted on a C-arm wheeled structure to provide wide variety of movement around the object. In this paper, C-arm tomosynthesis was introduced to provide three dimensional information over a limited view angle (less than 180o) to reduce radiation exposure and examination time. Reconstruction algorithms based on ray tracing method such as ray tracing back projection (BP), simultaneous algebraic reconstruction technique (SART) and maximum likelihood expectation maximization (MLEM) were developed for C-arm tomosynthesis. C-arm tomosynthesis projection images of simulated spherical object were simulated with a virtual geometric configuration with a total view angle of 40 degrees. This study demonstrated the sharpness of in-plane reconstructed structure and effectiveness of removing out-of-plane blur for each reconstruction algorithms. Results showed the ability of ray tracing based reconstruction algorithms to provide three dimensional information with limited angle C-arm tomosynthesis.
Trace chemical characterization using monochromatic X-ray undulator radiation
Eba; Numako; Iihara; Sakurai
2000-06-01
An efficient Johansson-type X-ray fluorescence spectrometer has been developed for advanced X-ray spectroscopic analysis with third-generation synchrotron radiation. Kalpha and Kbeta X-ray fluorescence spectra for trace metals have been collected by a Ge(220) analyzing crystal with a Rowland radius of 150 mm, under monochromatic X-ray excitation at the undulator beamline at the SPring-8. The energy resolution is approximately 10 eV for most of the K lines for 3d transition metals. In light of the greatly improved efficiency, as well as the excellent signal-to-background ratio, the relative and absolute detection limits achieved are 1 ppm and 1.2 ng of copper in a carbon matrix, respectively. The energy resolution of the present spectrometer permits the observation of some chemical effects in Kbeta spectra. It has been demonstrated that the changes in Kbeta5 and Kbeta'' intensity for iron and cobalt compounds can be used for the analysis of chemical states. Resonant X-ray fluorescent spectra are another important application of monochromatic excitation. In view of trace chemical characterization, the present spectrometer can be a good alternative to a conventional Si(Li) detector system when combined with highly brilliant X-rays.
McXtrace: A modern ray-tracing package for X-ray instrumentation
Bergbäck Knudsen, Erik; Prodi, A.; Willendrup, Peter Kjær
2011-01-01
we present the developments of the McXtrace project, a free, open source software package based on Monte Carlo ray tracing for simulations and optimisation of complete X-ray instruments. The methodology of building a simulation is presented through an example beamline, namely Beamline 811 at MAX-...
3D ultrasonic ray tracing in AutoCAD®
Reilly, D.; Leggat, P.; McNab, A.
2001-04-01
To assist with the design and validation of testing procedures for NDT, add-on modules have been developed for AutoCAD® 2000. One of the modules computes and displays ultrasonic 3D ray tracing. Another determines paths between two points, for instance a probe and a target or two probes. The third module displays phased array operational modes and calculates element delays for phased array operation. The modules can be applied to simple or complex solid model components.
Tropospheric Refraction Modeling Using Ray-Tracing and Parabolic Equation
P. Pechac
2005-12-01
Full Text Available Refraction phenomena that occur in the lower atmospheresignificantly influence the performance of wireless communicationsystems. This paper provides an overview of corresponding computationalmethods. Basic properties of the lower atmosphere are mentioned.Practical guidelines for radiowave propagation modeling in the loweratmosphere using ray-tracing and parabolic equation methods are given.In addition, a calculation of angle-of-arrival spectra is introducedfor multipath propagation simulations.
Ray Tracing Modelling of Reflector for Vertical Bifacial Panel
Jakobsen, Michael Linde; Thorsteinsson, Sune; Poulsen, Peter Behrensdorff
2016-01-01
Bifacial solar panels have recently become a new attractive building block for PV systems. In this work we propose a reflector system for a vertical bifacial panel, and use ray tracing modelling to model the performance. Particularly, we investigate the impact of the reflector volume being filled...... with a refractive medium, and shows the refractive medium improves the reflector performance since it directs almost all the light incident on the incoming plane into the PV panel....
The Search for Efficiency in Arboreal Ray Tracing Applications
van Leeuwen, M.; Disney, M.; Chen, J. M.; Gomez-Dans, J.; Kelbe, D.; van Aardt, J. A.; Lewis, P.
2016-12-01
Forest structure significantly impacts a range of abiotic conditions, including humidity and the radiation regime, all of which affect the rate of net and gross primary productivity. Current forest productivity models typically consider abstract media to represent the transfer of radiation within the canopy. Examples include the representation forest structure via a layered canopy model, where leaf area and inclination angles are stratified with canopy depth, or as turbid media where leaves are randomly distributed within space or within confined geometric solids such as blocks, spheres or cones. While these abstract models are known to produce accurate estimates of primary productivity at the stand level, their limited geometric resolution restricts applicability at fine spatial scales, such as the cell, leaf or shoot levels, thereby not addressing the full potential of assimilation of data from laboratory and field measurements with that of remote sensing technology. Recent research efforts have explored the use of laser scanning to capture detailed tree morphology at millimeter accuracy. These data can subsequently be used to combine ray tracing with primary productivity models, providing an ability to explore trade-offs among different morphological traits or assimilate data from spatial scales, spanning the leaf- to the stand level. Ray tracing has a major advantage of allowing the most accurate structural description of the canopy, and can directly exploit new 3D structural measurements, e.g., from laser scanning. However, the biggest limitation of ray tracing models is their high computational cost, which currently limits their use for large-scale applications. In this talk, we explore ways to more efficiently exploit ray tracing simulations and capture this information in a readily computable form for future evaluation, thus potentially enabling large-scale first-principles forest growth modelling applications.
Distance measurement based on light field geometry and ray tracing.
Chen, Yanqin; Jin, Xin; Dai, Qionghai
2017-01-09
In this paper, we propose a geometric optical model to measure the distances of object planes in a light field image. The proposed geometric optical model is composed of two sub-models based on ray tracing: object space model and image space model. The two theoretic sub-models are derived on account of on-axis point light sources. In object space model, light rays propagate into the main lens and refract inside it following the refraction theorem. In image space model, light rays exit from emission positions on the main lens and subsequently impinge on the image sensor with different imaging diameters. The relationships between imaging diameters of objects and their corresponding emission positions on the main lens are investigated through utilizing refocusing and similar triangle principle. By combining the two sub-models together and tracing light rays back to the object space, the relationships between objects' imaging diameters and corresponding distances of object planes are figured out. The performance of the proposed geometric optical model is compared with existing approaches using different configurations of hand-held plenoptic 1.0 cameras and real experiments are conducted using a preliminary imaging system. Results demonstrate that the proposed model can outperform existing approaches in terms of accuracy and exhibits good performance at general imaging range.
Ray tracing and ECRH absorption modeling in the HSX stellarator
Weir, G. M.; Likin, K. M.; Marushchenko, N. B.; Turkin, Y.
2015-09-01
To increase flexibility in ECRH experiments on the helically symmetric experiment (HSX), a second gyrotron and transmission line have been installed. The second antenna includes a steerable mirror for off-axis heating, and the launched power may be modulated for use in heat pulse propagation experiments. The extraordinary wave at the second harmonic of the electron gyrofrequency or the ordinary wave at the fundamental resonance are used for plasma start-up and heating on HSX. The tracing visualized ray tracing code (Marushchenko et al 2007 Plasma Fusion Res. 2 S1129) is used to estimate single-pass absorption and to model multi-pass wave damping in the three-dimensional HSX geometry. The single-pass absorption of the ordinary wave at the fundamental resonance is calculated to be as high as 30%, while measurements of the total absorption indicate that 45% of the launched power is absorbed. A multi-pass ray tracing model correctly predicts the experimental absorption and indicates that the launched power is absorbed within the plasma core (r/a≤slant 0.2 ).
Dynamic ray tracing and its application in triangulated media
Rueger, A.
1993-07-01
Hale and Cohen (1991) developed software to generate two-dimensional computer models of complex geology. Their method uses a triangulation technique designed to support efficient and accurate computation of seismic wavefields for models of the earth`s interior. Subsequently, Hale (1991) used this triangulation approach to perform dynamic ray tracing and create synthetic seismograms based on the method of Gaussian beams. Here, I extend this methodology to allow an increased variety of ray-theoretical experiments. Specifically, the developed program GBmod (Gaussian Beam MODeling) can produce arbitrary multiple sequences and incorporate attenuation and density variations. In addition, I have added an option to perform Fresnel-volume ray tracing (Cerveny and Soares, 1992). Corrections for reflection and transmission losses at interfaces, and for two-and-one-half-dimensional (2.5-D) spreading are included. However, despite these enhancements, difficulties remain in attempts to compute accurate synthetic seismograms if strong lateral velocity inhomogeneities are present. Here, these problems are discussed and, to a certain extent, reduced. I provide example computations of high-frequency seismograms based on the method of Gaussian beams to exhibit the advantages and disadvantages of the proposed modeling method and illustrate new features for both surface and vertical seismic profiling (VSP) acquisition geometries.
Microseismic network design assessment based on 3D ray tracing
Näsholm, Sven Peter; Wuestefeld, Andreas; Lubrano-Lavadera, Paul; Lang, Dominik; Kaschwich, Tina; Oye, Volker
2016-04-01
There is increasing demand on the versatility of microseismic monitoring networks. In early projects, being able to locate any triggers was considered a success. These early successes led to a better understanding of how to extract value from microseismic results. Today operators, regulators, and service providers work closely together in order to find the optimum network design to meet various requirements. In the current study we demonstrate an integrated and streamlined network capability assessment approach. It is intended for use during the microseismic network design process prior to installation. The assessments are derived from 3D ray tracing between a grid of event points and the sensors. Three aspects are discussed: 1) Magnitude of completeness or detection limit; 2) Event location accuracy; and 3) Ground-motion hazard. The network capability parameters 1) and 2) are estimated at all hypothetic event locations and are presented in the form of maps given a seismic sensor coordinate scenario. In addition, the ray tracing traveltimes permit to estimate the point-spread-functions (PSFs) at the event grid points. PSFs are useful in assessing the resolution and focusing capability of the network for stacking-based event location and imaging methods. We estimate the performance for a hypothetical network case with 11 sensors. We consider the well-documented region around the San Andreas Fault Observatory at Depth (SAFOD) located north of Parkfield, California. The ray tracing is done through a detailed velocity model which covers a 26.2 by 21.2 km wide area around the SAFOD drill site with a resolution of 200 m both for the P-and S-wave velocities. Systematic network capability assessment for different sensor site scenarios prior to installation facilitates finding a final design which meets the survey objectives.
Trans-Ionospheric High Frequency Signal Ray Tracing
Wright, S.; Gillespie, R. J.
2012-09-01
All electromagnetic radiation undergoes refraction as it propagates through the atmosphere. Tropospheric refraction is largely governed by interaction of the radiation with bounded electrons; ionospheric refraction is primarily governed by free electron interactions. The latter phenomenon is important for propagation and refraction of High Frequency (HF) through Extremely High Frequency (EHF) signals. The degree to which HF to EHF signals are bent is dependent upon the integrated refractive effect of the ionosphere: a result of the signal's angle of incidence with the boundaries between adjacent ionospheric regions, the magnitude of change in electron density between two regions, as well as the frequency of the signal. In the case of HF signals, the ionosphere may bend the signal so much that it is directed back down towards the Earth, making over-the-horizon HF radio communication possible. Ionospheric refraction is a major challenge for space-based geolocation applications, where the ionosphere is typically the biggest contributor to geolocation error. Accurate geolocation requires an algorithm that accurately reflects the physical process of a signal transiting the ionosphere, and an accurate specification of the ionosphere at the time of the signal transit. Currently implemented solutions are limited by both the algorithm chosen to perform the ray trace and by the accuracy of the ionospheric data used in the calculations. This paper describes a technique for adapting a ray tracing algorithm to run on a General-Purpose Graphics Processing Unit (GPGPU or GPU), and using a physics-based model specifying the ionosphere at the time of signal transit. This technique allows simultaneous geolocation of significantly more signals than an equivalently priced Central Processing Unit (CPU) based system. Additionally, because this technique makes use of the most widely accepted numeric algorithm for ionospheric ray tracing and a timely physics-based model of the ionosphere
Modular soft x-ray spectrometer for applications in energy sciences and quantum materials
Chuang, Yi-De; Shao, Yu-Cheng; Cruz, Alejandro; Hanzel, Kelly; Brown, Adam; Frano, Alex; Qiao, Ruimin; Smith, Brian; Domning, Edward; Huang, Shih-Wen; Wray, L. Andrew; Lee, Wei-Sheng; Shen, Zhi-Xun; Devereaux, Thomas P.; Chiou, Jaw-Wern; Pong, Way-Faung; Yashchuk, Valeriy V.; Gullikson, Eric; Reininger, Ruben; Yang, Wanli; Guo, Jinghua; Duarte, Robert; Hussain, Zahid
2017-01-01
Over the past decade, the advances in grating-based soft X-ray spectrometers have revolutionized the soft X-ray spectroscopies in materials research. However, these novel spectrometers are mostly dedicated designs, which cannot be easily adopted for applications with diverging demands. Here we present a versatile spectrometer design concept based on the Hettrick-Underwood optical scheme that uses modular mechanical components. The spectrometer's optics chamber can be used with gratings operated in either inside or outside orders, and the detector assembly can be reconfigured accordingly. The spectrometer can be designed to have high spectral resolution, exceeding 10 000 resolving power when using small source (˜1 μ m) and detector pixels (˜5 μ m) with high line density gratings (˜3000 lines/mm), or high throughput at moderate resolution. We report two such spectrometers with slightly different design goals and optical parameters in this paper. We show that the spectrometer with high throughput and large energy window is particularly useful for studying the sustainable energy materials. We demonstrate that the extensive resonant inelastic X-ray scattering (RIXS) map of battery cathode material LiNi1/3Co1/3Mn1/3O2 can be produced in few hours using such a spectrometer. Unlike analyzing only a handful of RIXS spectra taken at selected excitation photon energies across the elemental absorption edges to determine various spectral features like the localized dd excitations and non-resonant fluorescence emissions, these features can be easily identified in the RIXS maps. Studying such RIXS maps could reveal novel transition metal redox in battery compounds that are sometimes hard to be unambiguously identified in X-ray absorption and emission spectra. We propose that this modular spectrometer design can serve as the platform for further customization to meet specific scientific demands.
Photorealistic ray tracing to visualize automobile side mirror reflective scenes.
Lee, Hocheol; Kim, Kyuman; Lee, Gang; Lee, Sungkoo; Kim, Jingu
2014-10-20
We describe an interactive visualization procedure for determining the optimal surface of a special automobile side mirror, thereby removing the blind spot, without the need for feedback from the error-prone manufacturing process. If the horizontally progressive curvature distributions are set to the semi-mathematical expression for a free-form surface, the surface point set can then be derived through numerical integration. This is then converted to a NURBS surface while retaining the surface curvature. Then, reflective scenes from the driving environment can be virtually realized using photorealistic ray tracing, in order to evaluate how these reflected images would appear to drivers.
Adaptive image ray-tracing for astrophysical simulations
Parkin, E R
2010-01-01
A technique is presented for producing synthetic images from numerical simulations whereby the image resolution is adapted around prominent features. In so doing, adaptive image ray-tracing (AIR) improves the efficiency of a calculation by focusing computational effort where it is needed most. The results of test calculations show that a factor of >~ 4 speed-up, and a commensurate reduction in the number of pixels required in the final image, can be achieved compared to an equivalent calculation with a fixed resolution image.
The ray-tracing mapping operator in an asymmetric atmosphere
无
2008-01-01
In a spherically symmetric atmosphere, the refractive index profile is retrieved from bending angle measurements through Abel integral transform. As horizontal refractivity inhomogeneity becomes significant in the moist low atmosphere, the error in refractivity profile obtained from Abel inversion reaches about 10%. One way to avoid this error is to directly assimilate bending angle profile into numerical weather models. This paper discusses the 2D ray-tracing mapping operator for bending angle in an asymmetric atmosphere. Through simulating computations, the retrieval error of the refractivity in horizontal inhomogeneity is assessed. The step length of 4 rank Runge-Kutta method is also tested.
Ray tracing study for non-imaging daylight collectors
Wittkopf, Stephen [Solar Energy Research Institute of Singapore (SERIS), National University of Singapore (NUS), 7 Engineering Drive 1, Block E3A, 06-01, Singapore 117574 (Singapore); Solar Energy and Building Physics Laboratory (LESO), Swiss Federal Institute of Technology Lausanne (EPFL) (Switzerland); Oliver Grobe, Lars; Geisler-Moroder, David [Solar Energy Research Institute of Singapore (SERIS), National University of Singapore (NUS), 7 Engineering Drive 1, Block E3A, 06-01, Singapore 117574 (Singapore); Compagnon, Raphael [College of Engineering and Architecture of Fribourg (EIA-FR), University of Applied Sciences of Western Switzerland (HES-SO) (Switzerland); Kaempf, Jerome; Linhart, Friedrich; Scartezzini, Jean-Louis [Solar Energy and Building Physics Laboratory (LESO), Swiss Federal Institute of Technology Lausanne (EPFL) (Switzerland)
2010-06-15
This paper presents a novel method to study how well non-imaging daylight collectors pipe diffuse daylight into long horizontal funnels for illuminating deep buildings. Forward ray tracing is used to derive luminous intensity distributions curves (LIDC) of such collectors centered in an arc-shaped light source representing daylight. New photometric characteristics such as 2D flux, angular spread and horizontal offset are introduced as a function of such LIDC. They are applied for quantifying and thus comparing different collector contours. (author)
Ray-tracing optical modeling of negative dysphotopsia
Hong, Xin; Liu, Yueai; Karakelle, Mutlu; Masket, Samuel; Fram, Nicole R.
2011-12-01
Negative dysphotopsia is a relatively common photic phenomenon that may occur after implantation of an intraocular lens. The etiology of negative dysphotopsia is not fully understood. In this investigation, optical modeling was developed using nonsequential-component Zemax ray-tracing technology to simulate photic phenomena experienced by the human eye. The simulation investigated the effects of pupil size, capsulorrhexis size, and bag diffusiveness. Results demonstrated the optical basis of negative dysphotopsia. We found that photic structures were mainly influenced by critical factors such as the capsulorrhexis size and the optical diffusiveness of the capsular bag. The simulations suggested the hypothesis that the anterior capsulorrhexis interacting with intraocular lens could induce negative dysphotopsia.
Ray-tracing software comparison for linear focusing solar collectors
Osório, Tiago; Horta, Pedro; Larcher, Marco; Pujol-Nadal, Ramón; Hertel, Julian; van Rooyen, De Wet; Heimsath, Anna; Schneider, Simon; Benitez, Daniel; Frein, Antoine; Denarie, Alice
2016-05-01
Ray-Tracing software tools have been widely used in the optical design of solar concentrating collectors. In spite of the ability of these tools to assess the geometrical and material aspects impacting the optical performance of concentrators, their use in combination with experimental measurements in the framework of collector testing procedures as not been implemented, to the date, in none of the current solar collector testing standards. In the latest revision of ISO9806 an effort was made to include linear focusing concentrating collectors but some practical and theoretical difficulties emerged. A Ray-Tracing analysis could provide important contributions to overcome these issues, complementing the experimental results obtained through thermal testing and allowing the achievement of more thorough testing outputs with lower experimental requirements. In order to evaluate different available software tools a comparison study was conducted. Taking as representative technologies for line-focus concentrators the Parabolic Trough Collector and the Linear Fresnel Reflector Collector, two exemplary cases with predefined conditions - geometry, sun model and material properties - were simulated with different software tools. This work was carried out within IEA/SHC Task 49 "Solar Heat Integration in Industrial Processes".
Characterization of a new modular decay total absorption gamma-ray spectrometer (DTAS) for FAIR
Montaner Piza, A.; Tain, J. L.; Agramunt, J.; Algora, A.; Guadilla, V.; Marin, E.; Rice, S.; Rubio, B. [Instituto de Fisica Corpuscular, CSIC-Univ. de Valencia, Apdo. Correos 22085, E-46071 Valencia (Spain)
2013-06-10
Beta-decay studies are one of the main goals of the DEcay SPECtroscopy experiment (DESPEC) to be installed at the future Facility for Antiproton and Ion Research (FAIR). DESPEC aims at the study of nuclear structure of exotic nuclei. A new modular Decay Total Absorption gamma-ray Spectrometer (DTAS) is being built at IFIC and is specially adapted to studies at fragmentation facilities such as the Super Fragment Separator (Super-FRS) at FAIR. The designed spectrometer is composed of 16 identical NaI(Tl) scintillation crystals. This work focuses on the characterization of these independent modules, as an initial step for the characterization of the full spectrometer. Monte Carlo simulations have been performed in order to understand the detector response.
Performance Evaluation of a Modular Detector Unit for X-Ray Computed Tomography
Guangshu Hu
2013-04-01
Full Text Available A research prototype CT scanner is currently under development in our lab. One of the key components in this project is the CT detector. This paper describes the design and performance evaluation of the modular CT detector unit for our proposed scanner. It consists of a Photodiode Array Assembly which captures irradiating X-ray photons and converts the energy into electrical current, and a mini Data Acquisition System which performs current integration and converts the analog signal into digital samples. The detector unit can be easily tiled together to form a CT detector. Experiments were conducted to characterize the detector performance both at the single unit level and system level. The noise level, linearity and uniformity of the proposed detector unit were reported and initial imaging studies were also presented which demonstrated the potential application of the proposed detector unit in actual CT scanners.
High performance dosimetry calculations using adapted ray-tracing
Perrotte, Lancelot; Saupin, Guillaume
2010-11-01
When preparing interventions on nuclear sites, it is interesting to study different scenarios, to identify the most appropriate one for the operator(s). Using virtual reality tools is a good way to simulate the potential scenarios. Thus, taking advantage of very efficient computation times can help the user studying different complex scenarios, by immediately evaluating the impact of any changes. In the field of radiation protection, people often use computation codes based on the straight line attenuation method with build-up factors. As for other approaches, geometrical computations (finding all the interactions between radiation rays and the scene objects) remain the bottleneck of the simulation. We present in this paper several optimizations used to speed up these geometrical computations, using innovative GPU ray-tracing algorithms. For instance, we manage to compute every intersectionbetween 600 000 rays and a huge 3D industrial scene in a fraction of second. Moreover, our algorithm works the same way for both static and dynamic scenes, allowing easier study of complex intervention scenarios (where everything moves: the operator(s), the shielding objects, the radiation sources).
The Verification and Validation of the Ray-tracing of Bag of Triangles (BoTs)
2015-02-01
The Verification and Validation of the Ray-tracing of Bag of Triangles ( BoTs ) by Charith Ranawake ARL-CR-0761 February 2015...Ground, MD 22105 ARL-CR-0761 February 2015 The Verification and Validation of the Ray-tracing of Bag of Triangles ( BoTs ) Charith...and Validation of the Ray-tracing of Bag of Triangles ( BoTs ) 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S
Ionospheric Plasma Drift Analysis Technique Based On Ray Tracing
Ari, Gizem; Toker, Cenk
2016-07-01
Ionospheric drift measurements provide important information about the variability in the ionosphere, which can be used to quantify ionospheric disturbances caused by natural phenomena such as solar, geomagnetic, gravitational and seismic activities. One of the prominent ways for drift measurement depends on instrumentation based measurements, e.g. using an ionosonde. The drift estimation of an ionosonde depends on measuring the Doppler shift on the received signal, where the main cause of Doppler shift is the change in the length of the propagation path of the signal between the transmitter and the receiver. Unfortunately, ionosondes are expensive devices and their installation and maintenance require special care. Furthermore, the ionosonde network over the world or even Europe is not dense enough to obtain a global or continental drift map. In order to overcome the difficulties related to an ionosonde, we propose a technique to perform ionospheric drift estimation based on ray tracing. First, a two dimensional TEC map is constructed by using the IONOLAB-MAP tool which spatially interpolates the VTEC estimates obtained from the EUREF CORS network. Next, a three dimensional electron density profile is generated by inputting the TEC estimates to the IRI-2015 model. Eventually, a close-to-real situation electron density profile is obtained in which ray tracing can be performed. These profiles can be constructed periodically with a period of as low as 30 seconds. By processing two consequent snapshots together and calculating the propagation paths, we estimate the drift measurements over any coordinate of concern. We test our technique by comparing the results to the drift measurements taken at the DPS ionosonde at Pruhonice, Czech Republic. This study is supported by TUBITAK 115E915 and Joint TUBITAK 114E092 and AS CR14/001 projects.
RAY-RAMSES: a code for ray tracing on the fly in N-body simulations
Barreira, Alexandre; Bose, Sownak; Li, Baojiu
2016-01-01
We present a ray tracing code to compute integrated cosmological observables on the fly in AMR N-body simulations. Unlike conventional ray tracing techniques, our code takes full advantage of the time and spatial resolution attained by the N-body simulation by computing the integrals along the line of sight on a cell-by-cell basis through the AMR simulation grid. Moroever, since it runs on the fly in the N-body run, our code can produce maps of the desired observables without storing large (or any) amounts of data for post-processing. We implemented our routines in the RAMSES N-body code and tested the implementation using an example of weak lensing simulation. We analyse basic statistics of lensing convergence maps and find good agreement with semi-analytical methods. The ray tracing methodology presented here can be used in several cosmological analysis such as Sunyaev-Zel'dovich and integrated Sachs-Wolfe effect studies as well as modified gravity. Our code can also be used in cross-checks of the more conv...
Design of a modular signal processing board (MSPB) for gamma-ray imaging applications
Bieberle, A., E-mail: A.Bieberle@hzdr.de [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Safety Research, Bautzner Landstrasse 400, 01328 Dresden (Germany); Berger, R.; Yadav, R.; Schleicher, E.; Hampel, U. [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Safety Research, Bautzner Landstrasse 400, 01328 Dresden (Germany)
2012-01-21
In this paper a new modular signal processing board (MSPB) for high-resolution gamma-ray computed tomography (GCT) is presented. The MSPB is optimised for parallel signal processing of eight detector channels operating in pulse counting mode. Signal processing stages comprise of variable gain amplifiers, pulse height discrimination stages, 13-bit counters with corresponding latches as well as logic circuitry for coordinated data transfer with a multitude of MSPBs. The digital signal processing units are realised in commercially available complex programmable logic devices (CPLD). Each MSPB is addressable by an 8-bit DIP-switch, which allows the use of up to 256 modules or 2048 detector pixels within one detector system. The geometry of the MSPB allows a multiple and seamless detector module arrangement, which eases the adaptation of a given gamma-ray detector system to specific industrial and laboratory applications. The choice of the electronic devices and the thermal design was optimised for low power consumption in order to minimise internal heat production, which would affect the characteristics of the detector's intrinsic gain strongly. Thermal measurements have been executed to prove the functionality of the thermal design.
Baltser, Jana; Bergbäck Knudsen, Erik; Vickery, Anette
2011-01-01
of X-ray beamline designs for particular user experiments. In this work we used the newly developed McXtrace ray-tracing package and the SRW wave-optics code to simulate the beam propagation of X-ray undulator radiation through such a "transfocator" as implemented at ID- 11 at ESRF. By applying two...
Testing the validity of the ray-tracing code GYOTO
Grould, Marion; Perrin, Guy
2016-01-01
In the next few years, the near-infrared interferometer GRAVITY will be able to observe the Galactic center. Astrometric data will be obtained with an anticipated accuracy of 10 $\\mu$as. To analyze these future data, we have developed a code called GYOTO to compute orbits and images. We want to assess the validity and accuracy of GYOTO in a variety of contexts, in particular for stellar astrometry in the Galactic center. Furthermore, we want to tackle and complete a study made on the astrometric displacements that are due to lensing effects of a star of the central parsec with GYOTO. We first validate GYOTO in the weak-deflection limit (WDL) by studying primary caustics and primary critical curves obtained for a Kerr black hole. We compare GYOTO results to available analytical approximations and estimate GYOTO errors using an intrinsic estimator. In the strong-deflection limit (SDL), we choose to compare null geodesics computed by GYOTO and the ray-tracing code named Geokerr. Finally, we use GYOTO to estimate...
Fast Ray Tracing of Lunar Digital Elevation Models
McClanahan, Timothy P.; Evans, L. G.; Starr, R. D.; Mitrofanov, I.
2009-01-01
Ray-tracing (RT) of Lunar Digital Elevation Models (DEM)'s is performed to virtually derive the degree of radiation incident to terrain as a function of time, orbital and ephemeris constraints [I- 4]. This process is an integral modeling process in lunar polar research and exploration due to the present paucity of terrain information at the poles and mission planning activities for the anticipated spring 2009 launch of the Lunar Reconnaissance Orbiter (LRO). As part of the Lunar Exploration Neutron Detector (LEND) and Lunar Crater Observation and Sensing Satellite (LCROSS) preparations RI methods are used to estimate the critical conditions presented by the combined effects of high latitude, terrain and the moons low obliquity [5-7]. These factors yield low incident solar illumination and subsequently extreme thermal, and radiation conditions. The presented research uses RT methods both for radiation transport modeling in space and regolith related research as well as to derive permanently shadowed regions (PSR)'s in high latitude topographic minima, e.g craters. These regions are of scientific and human exploration interest due to the near constant low temperatures in PSRs, inferred to be < 100 K. Hydrogen is thought to have accumulated in PSR's through the combined effects of periodic cometary bombardment and/or solar wind processes, and the extreme cold which minimizes hydrogen sublimation [8-9]. RT methods are also of use in surface position optimization for future illumination dependent on surface resources e.g. power and communications equipment.
Virtual Ray Tracing as a Conceptual Tool for Image Formation in Mirrors and Lenses
Heikkinen, Lasse; Savinainen, Antti; Saarelainen, Markku
2016-12-01
The ray tracing method is widely used in teaching geometrical optics at the upper secondary and university levels. However, using simple and straightforward examples may lead to a situation in which students use the model of ray tracing too narrowly. Previous studies show that students seem to use the ray tracing method too concretely instead of as a conceptual model. This suggests that introductory physics students need to understand the nature of the ray model more profoundly. In this paper, we show how a virtual ray tracing model can be used as a tool for image formation in more complex and unconventional cases. We believe that this tool has potential in helping students to better appreciate the nature of the ray model.
Three-dimensional polarization ray-tracing calculus I: definition and diattenuation.
Yun, Garam; Crabtree, Karlton; Chipman, Russell A
2011-06-20
A three-by-three polarization ray-tracing matrix method for polarization ray tracing in optical systems is presented for calculating the polarization transformations associated with ray paths through optical systems. The method is a three-dimensional generalization of the Jones calculus. Reflection and refraction algorithms are provided. Diattenuation of the optical system is calculated via singular value decomposition. Two numerical examples, a three fold-mirror system and a hollow corner cube, demonstrate the method.
Application of ray-traced tropospheric slant delays to geodetic VLBI analysis
Hofmeister, Armin; Böhm, Johannes
2017-02-01
The correction of tropospheric influences via so-called path delays is critical for the analysis of observations from space geodetic techniques like the very long baseline interferometry (VLBI). In standard VLBI analysis, the a priori slant path delays are determined using the concept of zenith delays, mapping functions and gradients. The a priori use of ray-traced delays, i.e., tropospheric slant path delays determined with the technique of ray-tracing through the meteorological data of numerical weather models (NWM), serves as an alternative way of correcting the influences of the troposphere on the VLBI observations within the analysis. In the presented research, the application of ray-traced delays to the VLBI analysis of sessions in a time span of 16.5 years is investigated. Ray-traced delays have been determined with program RADIATE (see Hofmeister in Ph.D. thesis, Department of Geodesy and Geophysics, Faculty of Mathematics and Geoinformation, Technische Universität Wien. http://resolver.obvsg.at/urn:nbn:at:at-ubtuw:1-3444, 2016) utilizing meteorological data provided by NWM of the European Centre for Medium-Range Weather Forecasts (ECMWF). In comparison with a standard VLBI analysis, which includes the tropospheric gradient estimation, the application of the ray-traced delays to an analysis, which uses the same parameterization except for the a priori slant path delay handling and the used wet mapping factors for the zenith wet delay (ZWD) estimation, improves the baseline length repeatability (BLR) at 55.9% of the baselines at sub-mm level. If no tropospheric gradients are estimated within the compared analyses, 90.6% of all baselines benefit from the application of the ray-traced delays, which leads to an average improvement of the BLR of 1 mm. The effects of the ray-traced delays on the terrestrial reference frame are also investigated. A separate assessment of the RADIATE ray-traced delays is carried out by comparison to the ray-traced delays from the
Application of ray-traced tropospheric slant delays to geodetic VLBI analysis
Hofmeister, Armin; Böhm, Johannes
2017-08-01
The correction of tropospheric influences via so-called path delays is critical for the analysis of observations from space geodetic techniques like the very long baseline interferometry (VLBI). In standard VLBI analysis, the a priori slant path delays are determined using the concept of zenith delays, mapping functions and gradients. The a priori use of ray-traced delays, i.e., tropospheric slant path delays determined with the technique of ray-tracing through the meteorological data of numerical weather models (NWM), serves as an alternative way of correcting the influences of the troposphere on the VLBI observations within the analysis. In the presented research, the application of ray-traced delays to the VLBI analysis of sessions in a time span of 16.5 years is investigated. Ray-traced delays have been determined with program RADIATE (see Hofmeister in Ph.D. thesis, Department of Geodesy and Geophysics, Faculty of Mathematics and Geoinformation, Technische Universität Wien. http://resolver.obvsg.at/urn:nbn:at:at-ubtuw:1-3444, 2016) utilizing meteorological data provided by NWM of the European Centre for Medium-Range Weather Forecasts (ECMWF). In comparison with a standard VLBI analysis, which includes the tropospheric gradient estimation, the application of the ray-traced delays to an analysis, which uses the same parameterization except for the a priori slant path delay handling and the used wet mapping factors for the zenith wet delay (ZWD) estimation, improves the baseline length repeatability (BLR) at 55.9% of the baselines at sub-mm level. If no tropospheric gradients are estimated within the compared analyses, 90.6% of all baselines benefit from the application of the ray-traced delays, which leads to an average improvement of the BLR of 1 mm. The effects of the ray-traced delays on the terrestrial reference frame are also investigated. A separate assessment of the RADIATE ray-traced delays is carried out by comparison to the ray-traced delays from the
A three-dimensional sound ray tracing method by deploying regular tetrahedrons
JIANG Wei; LI Taibao
2005-01-01
A sound ray tracing algorithm is presented, which helps to rapidly find the sound ray trajectories in three-dimensional (3-D) space. At each step of ray tracing, a small regular tetrahedron is made in front of a ray, so that the sound speed field inside may be approximately regarded as linear. Since a ray trajectory in the linear sound speed field is always on a plane, it may be obtained by the two-dimensional (2-D) sound ray tracing method by deploying triangles.The theoretical derivation is given and a numerical model is discussed. It shows that the algorithm is fast and precise. It is also more concise and reliable than the traditional 3-D algorithms, and may be used to avoid the damage to the precision by the acoustic refraction in the 3-D ultrasound computerized tomography.
Study of improved ray tracing parallel algorithm for CGH of 3D objects on GPU
Cong, Bin; Jiang, Xiaoyu; Yao, Jun; Zhao, Kai
2014-11-01
An improved parallel algorithm for holograms of three-dimensional objects was presented. According to the physical characteristics and mathematical properties of the original ray tracing algorithm for computer generated holograms (CGH), using transform approximation and numerical analysis methods, we extract parts of ray tracing algorithm which satisfy parallelization features and implement them on graphics processing unit (GPU). Meanwhile, through proper design of parallel numerical procedure, we did parallel programming to the two-dimensional slices of three-dimensional object with CUDA. According to the experiments, an effective method of dealing with occlusion problem in ray tracing is proposed, as well as generating the holograms of 3D objects with additive property. Our results indicate that the improved algorithm can effectively shorten the computing time. Due to the different sizes of spatial object points and hologram pixels, the speed has increased 20 to 70 times comparing with original ray tracing algorithm.
Validation of Three-Dimensional Ray-Tracing Algorithm for Indoor Wireless Propagations
Majdi Salem; Mahamod Ismail; Norbahiah Misran
2011-01-01
A 3D ray tracing simulator has been developed for indoor wireless networks. The simulator uses geometrical optics (GOs) to propagate the electromagnetic waves inside the buildings. The prediction technique takes into account multiple reflections and transmissions of the propagated waves. An interpolation prediction method (IPM) has been proposed to predict the propagated signal and to make the ray-tracing algorithm faster, accurate, and simple. The measurements have been achieved by using a s...
Fox, Christopher; Romeijn, H Edwin; Dempsey, James F
2006-05-01
We present work on combining three algorithms to improve ray-tracing efficiency in radiation therapy dose computation. The three algorithms include: An improved point-in-polygon algorithm, incremental voxel ray tracing algorithm, and stereographic projection of beamlets for voxel truncation. The point-in-polygon and incremental voxel ray-tracing algorithms have been used in computer graphics and nuclear medicine applications while the stereographic projection algorithm was developed by our group. These algorithms demonstrate significant improvements over the current standard algorithms in peer reviewed literature, i.e., the polygon and voxel ray-tracing algorithms of Siddon for voxel classification (point-in-polygon testing) and dose computation, respectively, and radius testing for voxel truncation. The presented polygon ray-tracing technique was tested on 10 intensity modulated radiation therapy (IMRT) treatment planning cases that required the classification of between 0.58 and 2.0 million voxels on a 2.5 mm isotropic dose grid into 1-4 targets and 5-14 structures represented as extruded polygons (a.k.a. Siddon prisms). Incremental voxel ray tracing and voxel truncation employing virtual stereographic projection was tested on the same IMRT treatment planning cases where voxel dose was required for 230-2400 beamlets using a finite-size pencil-beam algorithm. Between a 100 and 360 fold cpu time improvement over Siddon's method was observed for the polygon ray-tracing algorithm to perform classification of voxels for target and structure membership. Between a 2.6 and 3.1 fold reduction in cpu time over current algorithms was found for the implementation of incremental ray tracing. Additionally, voxel truncation via stereographic projection was observed to be 11-25 times faster than the radial-testing beamlet extent approach and was further improved 1.7-2.0 fold through point-classification using the method of translation over the cross product technique.
Design of indoor WLANs: Combination of a ray-tracing tool with the BPSO method
Moreno Delgado, José; Domingo Gracia, Marta; Valle López, Luis; Pérez López, Jesús Ramón; Torres Jménez, Rafael Pedro; Basterrechea Verdeja, José
2015-01-01
This paper presents an approach that combines a ray tracing tool with a binary version of the particle swarm optimization method (BPSO) for the design of infrastructure mode indoor wireless local area networks (WLAN). The approach uses the power levels of a set of candidate access point (AP) locations obtained with the ray tracing tool at a mesh of potential receiver locations or test points to allow the BPSO optimizer to carry out the design of the WLAN. For this purpose, several restriction...
Ray-Tracing studies in a perturbed atmosphere I- The initial value problem
Tannous, C
2001-01-01
We report the development of a new ray-tracing simulation tool having the potential of the full characterization of a radio link through the accurate study of the propagation path of the signal from the transmitting to the receiving antennas across a perturbed atmosphere. The ray-tracing equations are solved, with controlled accuracy, in three dimensions (3D) and the propagation characteristics are obtained using various refractive index models. The launching of the rays, the atmospheric medium and its disturbances are characterized in 3D. The novelty in the approach stems from the use of special numerical techniques dealing with so called stiff differential equations without which no solution of the ray-tracing equations is possible. Starting with a given launching angle, the solution consists of the ray trajectory, the propagation time information at each point of the path, the beam spreading, the transmitted (resp. received) power taking account of the radiation pattern and orientation of the antennas and ...
Refined ray tracing inside single- and double-curvatured concave surfaces
Choudhury, Balamati
2016-01-01
This book describes the ray tracing effects inside different quadric surfaces. Analytical surface modeling is a priori requirement for electromagnetic (EM) analysis over aerospace platforms. Although numerically-specified surfaces and even non-uniform rational basis spline (NURBS) can be used for modeling such surfaces, for most practical EM applications, it is sufficient to model them as quadric surface patches and the hybrids thereof. It is therefore apparent that a vast majority of aerospace bodies can be conveniently modeled as combinations of simpler quadric surfaces, i.e. hybrid of quadric cylinders and quadric surfaces of revolutions. Hence the analysis of geometric ray tracing inside is prerequisite to analyzing the RF build-up. This book, describes the ray tracing effects inside different quadric surfaces such as right circular cylinder, general paraboloid of revolution (GPOR), GPOR frustum of different shaping parameters and the corresponding visualization of the ray-path details. Finally ray tracin...
Lund, Henrik Hautop; Pagliarini, Luigi
2009-01-01
In this concept paper we trace the contours and define a new approach to robotic systems, composed of interactive robotic modules which are somehow worn on the body. We label such a field as Modular Robotic Wearable (MRW). We describe how, by using modular robotics for creating wearable....... Finally, by focusing on the intersection of the combination modular robotic systems, wearability, and bodymind we attempt to explore the theoretical characteristics of such approach and exploit the possible playware application fields....
An expanded X-ray beam facility (BEaTriX) to test the modular elements of the ATHENA optics
Spiga, D; Bonnini, E; Buffagni, E; Ferrari, C; Pareschi, G; Tagliaferri, G
2015-01-01
Future large X-ray observatories like ATHENA will be equipped with very large optics, obtained by assembling modular optical elements, named X-ray Optical Units (XOU) based on the technology of either Silicon Pore Optics or Slumped Glass Optics. In both cases, the final quality of the modular optic (a 5 arcsec HEW requirement for ATHENA) is determined by the accuracy alignment of the XOUs within the assembly, but also by the angular resolution of the individual XOU. This is affected by the mirror shape accuracy, its surface roughness, and the mutual alignment of the mirrors within the XOU itself. Because of the large number of XOUs to be produced, quality tests need to be routinely done to select the most performing stacked blocks, to be integrated into the final optic. In addition to the usual metrology based on profile and roughness measurements, a direct measurement with a broad, parallel, collimated and uniform X- ray beam would be the most reliable test, without the need of a focal spot reconstruction as...
An expanded x-ray beam facility (BEaTriX) to test the modular elements of the ATHENA optics
Spiga, D.; Pelliciari, C.; Bonnini, E.; Buffagni, E.; Ferrari, C.; Pareschi, G.; Tagliaferri, G.
2014-07-01
Future large X-ray observatories like ATHENA will be equipped with very large optics, obtained by assembling modular optical elements, named X-ray Optical Units (XOU) based on the technology of either Silicon Pore Optics or Slumped Glass Optics. In both cases, the final quality of the modular optic (a 5 arcsec HEW requirement for ATHENA) is determined by the accuracy alignment of the XOUs within the assembly, but also by the angular resolution of the individual XOU. This is affected by the mirror shape accuracy, its surface roughness, and the mutual alignment of the mirrors within the XOU itself. Because of the large number of XOUs to be produced, quality tests need to be routinely done to select the most performing stacked blocks, to be integrated into the final optic. In addition to the usual metrology based on profile and roughness measurements, a direct measurement with a broad, parallel, collimated and uniform Xray beam would be the most reliable test, without the need of a focal spot reconstruction as usually done in synchrotron light. To this end, we designed the BEaTriX (Beam Expander Testing X-ray facility) to be realized at INAF-OAB, devoted to the functional tests of the XOUs. A grazing incidence parabolic mirror and an asymmetrically cut crystal will produce a parallel X-ray beam broad enough to illuminate the entire aperture of the focusing elements. An X-ray camera at the focal distance from the mirrors will directly record the image. The selection of different crystals will enable to test the XOUs in the 1 - 5 keV range, included in the X-ray energy band of ATHENA (0.2-12 keV). In this paper we discuss a possible BEaTriX facility implementation. We also show a preliminary performance simulation of the optical system.
The Gaussian Laser Angular Distribution in HYDRA's 3D Laser Ray Trace Package
Sepke, Scott M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)
2017-04-10
In this note, the angular distribution of rays launched by the 3D LZR ray trace package is derived for Gaussian beams (npower==2) with bm model=3±. Beams with bm model=+3 have a nearly at distribution, and beams with bm model=-3 have a nearly linear distribution when the spot size is large compared to the wavelength.
Real-time ray tracing of implicit surfaces on the GPU.
Singh, Jag Mohan; Narayanan, P J
2010-01-01
Compact representation of geometry using a suitable procedural or mathematical model and a ray-tracing mode of rendering fit the programmable graphics processor units (GPUs) well. Several such representations including parametric and subdivision surfaces have been explored in recent research. The important and widely applicable category of the general implicit surface has received less attention. In this paper, we present a ray-tracing procedure to render general implicit surfaces efficiently on the GPU. Though only the fourth or lower order surfaces can be rendered using analytical roots, our adaptive marching points algorithm can ray trace arbitrary implicit surfaces without multiple roots, by sampling the ray at selected points till a root is found. Adapting the sampling step size based on a proximity measure and a horizon measure delivers high speed. The sign test can handle any surface without multiple roots. The Taylor test that uses ideas from interval analysis can ray trace many surfaces with complex roots. Overall, a simple algorithm that fits the SIMD architecture of the GPU results in high performance. We demonstrate the ray tracing of algebraic surfaces up to order 50 and nonalgebraic surfaces including a Blinn's blobby with 75 spheres at better than interactive frame rates.
Skew ray tracing in a step-index optical fiber using Geometric Algebra
Ang, Angeleene; McNamara, Daniel J
2015-01-01
We used Geometric Algebra to compute the paths of skew rays in a cylindrical, step-index multimode optical fiber. To do this, we used the vector addition form for the law of propagation, the exponential of an imaginary vector form for the law of refraction, and the juxtaposed vector product form for the law of reflection. In particular, the exponential forms of the vector rotations enables us to take advantage of the addition or subtraction of exponential arguments of two rotated vectors in the derivation of the ray tracing invariants in cylindrical and spherical coordinates. We showed that the light rays inside the optical fiber trace a polygonal helical path characterized by three invariants that relate successive reflections inside the fiber: the ray path distance, the difference in axial distances, and the difference in the azimuthal angles. We also rederived the known generalized formula for the numerical aperture for skew rays, which simplifies to the standard form for meridional rays.
HUANG Yueqin; ZHANG Jianzhong
2008-01-01
A kind of three-dimensional(3-D) sound ray tracing algorithm in heterogeneous media is studied. This algorithm includes two steps: the first step computes the wavefront traveltimes forward; the second step traces the sound rays backward. In the first step, the computation of wavefront traveltimes at discrete grid points from the sound source, was found on Eikonal equation solutions and carried out by GMM (Group marching method) wavefront marching method based on level set. In the second step, sound ray tracing was proceeded gradually from the receiver to each cell towards the sound source, with wavefront traveltimes computed in the first step. Time values on arbitrary positions in each cuboid cell can be expressed by linear interpolation of wavefront traveltimes at the same cell's grid points. Thus,an algorithm of 3-D sound ray tracing in heterogeneous media is put forward. The simulation results indicate that this method can improve both the accuracy and the efficiency of 3-D sound ray tracing greatly.
SolTrace: A Ray-Tracing Code for Complex Solar Optical Systems
Wendelin, Tim [National Renewable Energy Lab. (NREL), Golden, CO (United States); Dobos, Aron [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lewandowski, Allan [Allan Lewandowski Solar Consulting LLC, Evergreen, CO (United States)
2013-10-01
SolTrace is an optical simulation tool designed to model optical systems used in concentrating solar power (CSP) applications. The code was first written in early 2003, but has seen significant modifications and changes since its inception, including conversion from a Pascal-based software development platform to C++. SolTrace is unique in that it can model virtually any optical system utilizingthe sun as the source. It has been made available for free and as such is in use worldwide by industry, universities, and research laboratories. The fundamental design of the code is discussed, including enhancements and improvements over the earlier version. Comparisons are made with other optical modeling tools, both non-commercial and commercial in nature. Finally, modeled results are shownfor some typical CSP systems and, in one case, compared to measured optical data.
Tracing Analytic Ray Curves for Light and Sound Propagation in Non-Linear Media.
Mo, Qi; Yeh, Hengchin; Manocha, Dinesh
2016-11-01
The physical world consists of spatially varying media, such as the atmosphere and the ocean, in which light and sound propagates along non-linear trajectories. This presents a challenge to existing ray-tracing based methods, which are widely adopted to simulate propagation due to their efficiency and flexibility, but assume linear rays. We present a novel algorithm that traces analytic ray curves computed from local media gradients, and utilizes the closed-form solutions of both the intersections of the ray curves with planar surfaces, and the travel distance. By constructing an adaptive unstructured mesh, our algorithm is able to model general media profiles that vary in three dimensions with complex boundaries consisting of terrains and other scene objects such as buildings. Our analytic ray curve tracer with the adaptive mesh improves the efficiency considerably over prior methods. We highlight the algorithm's application on simulation of visual and sound propagation in outdoor scenes.
Optimizing detector geometry for trace element mapping by X-ray fluorescence.
Sun, Yue; Gleber, Sophie-Charlotte; Jacobsen, Chris; Kirz, Janos; Vogt, Stefan
2015-05-01
Trace metals play critical roles in a variety of systems, ranging from cells to photovoltaics. X-Ray Fluorescence (XRF) microscopy using X-ray excitation provides one of the highest sensitivities available for imaging the distribution of trace metals at sub-100 nm resolution. With the growing availability and increasing performance of synchrotron light source based instruments and X-ray nanofocusing optics, and with improvements in energy-dispersive XRF detectors, what are the factors that limit trace element detectability? To address this question, we describe an analytical model for the total signal incident on XRF detectors with various geometries, including the spectral response of energy dispersive detectors. This model agrees well with experimentally recorded X-ray fluorescence spectra, and involves much shorter calculation times than with Monte Carlo simulations. With such a model, one can estimate the signal when a trace element is illuminated with an X-ray beam, and when just the surrounding non-fluorescent material is illuminated. From this signal difference, a contrast parameter can be calculated and this can in turn be used to calculate the signal-to-noise ratio (S/N) for detecting a certain elemental concentration. We apply this model to the detection of trace amounts of zinc in biological materials, and to the detection of small quantities of arsenic in semiconductors. We conclude that increased detector collection solid angle is (nearly) always advantageous even when considering the scattered signal. However, given the choice between a smaller detector at 90° to the beam versus a larger detector at 180° (in a backscatter-like geometry), the 90° detector is better for trace element detection in thick samples, while the larger detector in 180° geometry is better suited to trace element detection in thin samples.
Ray tracing optical analysis of offset solar collector for Space Station solar dynamic system
Jefferies, Kent S.
1988-01-01
OFFSET, a detailed ray tracing computer code, was developed at NASA Lewis Research Center to model the offset solar collector for the Space Station solar dynamic electric power system. This model traces rays from 50 points on the face of the sun to 10 points on each of the 456 collector facets. The triangular facets are modeled with spherical, parabolic, or toroidal reflective surface contour and surface slope errors. The rays are then traced through the receiver aperture to the walls of the receiver. Images of the collector and of the sun within the receiver produced by this code provide insight into the collector receiver interface. Flux distribution on the receiver walls, plotted by this code, is improved by a combination of changes to aperture location and receiver tilt angle. Power loss by spillage at the receiver aperture is computed and is considerably reduced by using toroidal facets.
Robust Image Denoising using a Virtual Flash Image for Monte Carlo Ray Tracing
Moon, Bochang; Jun, Jong Yun; Lee, JongHyeob
2013-01-01
parameters. To highlight the benefits of our method, we apply our method to two Monte Carlo ray tracing methods, photon mapping and path tracing, with various input scenes. We demonstrate that using virtual flash images and homogeneous pixels with a standard denoising method outperforms state-of-the-art......We propose an efficient and robust image-space denoising method for noisy images generated by Monte Carlo ray tracing methods. Our method is based on two new concepts: virtual flash images and homogeneous pixels. Inspired by recent developments in flash photography, virtual flash images emulate...... values. While denoising each pixel, we consider only homogeneous pixels—pixels that are statistically equivalent to each other. This makes it possible to define a stochastic error bound of our method, and this bound goes to zero as the number of ray samples goes to infinity, irrespective of denoising...
Defining Modules, Modularity and Modularization
Miller, Thomas Dedenroth; Pedersen, Per Erik Elgård
The paper describes the evolution of the concept of modularity in a historical perspective. The main reasons for modularity are: create variety, utilize similarities, and reduce complexity. The paper defines the terms: Module, modularity, and modularization.......The paper describes the evolution of the concept of modularity in a historical perspective. The main reasons for modularity are: create variety, utilize similarities, and reduce complexity. The paper defines the terms: Module, modularity, and modularization....
Reflection formulae for ray tracing in uniaxial anisotropic media using Huygens's principle.
Alemán-Castañeda, Luis A; Rosete-Aguilar, Martha
2016-11-01
Ray tracing in uniaxial anisotropic materials is important because they are widely used for instrumentation, liquid-crystal displays, laser cavities, and quantum experiments. There are previous works regarding ray tracing refraction and reflection formulae using the common electromagnetic theory approach, but only the refraction formulae have been deduced using Huygens's principle. In this paper we obtain the reflection expressions using this unconventional approach with a specific coordinate system in which both refraction and reflection formulae are simplified as well as their deduction. We compute some numerical examples to compare them with the common expressions obtained using electromagnetic theory.
A boundary integral formalism for stochastic ray tracing in billiards
Chappell, David J. [School of Science and Technology, Nottingham Trent University, Clifton Campus, Nottingham NG11 8NS (United Kingdom); Tanner, Gregor [School of Mathematical Sciences, University of Nottingham, University Park, Nottingham NG7 2RD (United Kingdom)
2014-12-15
Determining the flow of rays or non-interacting particles driven by a force or velocity field is fundamental to modelling many physical processes. These include particle flows arising in fluid mechanics and ray flows arising in the geometrical optics limit of linear wave equations. In many practical applications, the driving field is not known exactly and the dynamics are determined only up to a degree of uncertainty. This paper presents a boundary integral framework for propagating flows including uncertainties, which is shown to systematically interpolate between a deterministic and a completely random description of the trajectory propagation. A simple but efficient discretisation approach is applied to model uncertain billiard dynamics in an integrable rectangular domain.
a Highly-Accurate and Fast Ray Tracing Sysyem for HF and UHF Simulations
Jones, J. C.; Richards, G. P.
2016-12-01
Accurate and fast ray tracing is critical for radiowave propagation tools and applications. A ray tracer needs to be accurate to reduce accumulated errors which come from the myriad of models (ionospheric electron density, magnetic field, ion density, neutral molecule density, absorption, land surface, ocean surface, and potentially others) required for accurate simulation. A ray tracer must also be fast to make the use of applications practical. Here we introduce NINJART Is Not Just Another Ray Tracer (NINJART), a highly accurate and fast ray tracing system. NINJART consists of an embarrassingly parallel algorithm rigorously solving the 3-D Hasselgrove equations with a Runge-Kutta adaptive step quadrature rule to accurately trace high frequency to ultra-high frequency radiowaves. It is capable of a wide range of propagation modes from multi-ground hops to vertical and near vertical incidence rays, chordal modes, and other esoteric paths. It is capable of using a variety of ionospheric models to include operational data assimilative or empirical models depending on the needs of the user. It can forward and backward ray trace, calculate time of flight, find the focus factor for signals near the skip zone and calculate the angle of arrival from a known transmitter to a known receiver location. Additionally NINJART uses magnetic field data from various models including the International Geomagnetic Reference Field to reduce the inaccuracies introduced by the simple dipole model, which is commonly used by other ray tracers, in calculating the effects of magneto-ionic splitting thereby allowing accurate traces of both the ordinary and extraordinary mode rays. The NINJART algorithm is a heterogeneous system utilizing the CUDA programming language to take advantage of the computing power of graphical processing units. This allows tracing of thousands of rays concurrently. NINJART achieves additional processing savings, without sacrificing accuracy, by use of an adaptive
Magnetospheric Whistler Mode Ray Tracing with the Inclusion of Finite Electron and Ion Temperature
Maxworth, A. S.; Golkowski, M.
2015-12-01
Ray tracing is an important technique for the study of whistler mode wave propagation in the Earth's magnetosphere. In numerical ray tracing the trajectory of a wave packet is calculated at each point in space by solving the Haselgrove equations, assuming a smooth, loss-less medium with no mode coupling. Previous work on ray tracing has assumed a cold plasma environment with negligible electron and ion temperatures. In this work we present magnetospheric whistler mode wave ray tracing results with the inclusion of finite ion and electron temperature. The inclusion of finite temperature effects makes the fourth order dispersion relation become sixth order. We compare our results with the work done by previous researchers for cold plasma environments, using two near earth space models (NGO and GCPM). Inclusion of finite temperature closes the otherwise open refractive index surface near the lower hybrid resonance frequency and affects the magnetospheric reflection of whistler waves. We also asses the main changes in the ray trajectory and implications for cyclotron resonance wave particle interactions including energetic particle precipitation.
BEaTriX, expanded x-ray beam facility for testing modular elements of telescope optics: an update
Pelliciari, C.; Spiga, D.; Bonnini, E.; Buffagni, E.; Ferrari, C.; Pareschi, G.; Tagliaferri, G.
2015-09-01
We present in this paper an update on the design of BEaTriX (Beam Expander Testing X-ray facility), an X-ray apparatus to be realized at INAF/OAB and that will generate an expanded, uniform and parallel beam of soft X-rays. BEaTriX will be used to perform the functional tests of X-ray focusing modules of large X-ray optics such as those for the ATHENA X-ray observatory, using the Silicon Pore Optics (SPO) as a baseline technology, and Slumped Glass Optics (SGO) as a possible alternative. Performing the tests in X-rays provides the advantage of an in-situ, at-wavelength quality control of the optical modules produced in series by the industry, performing a selection of the modules with the best angular resolution, and, in the case of SPOs, there is also the interesting possibility to align the parabolic and the hyperbolic stacks directly under X-rays, to minimize the aberrations. However, a parallel beam with divergence below 2 arcsec is necessary in order to measure mirror elements that are expected to reach an angular resolution of about 4 arcsec, since the ATHENA requirement for the entire telescope is 5 arcsec. Such a low divergence over the typical aperture of modular optics would require an X-ray source to be located in a several kilometers long vacuum tube. In contrast, BEaTriX will be compact enough (5 m x 14 m) to be housed in a small laboratory, will produce an expanded X-ray beam 60 mm x 200 mm broad, characterized by a very low divergence (1.5 arcsec HEW), strong polarization, high uniformity, and X-ray energy selectable between 1.5 keV and 4.5 keV. In this work we describe the BEaTriX layout and show a performance simulation for the X-ray energy of 4.5 keV.
Odyssey: Ray tracing and radiative transfer in Kerr spacetime
Pu, Hung-Yi; Yun, Kiyun; Younsi, Ziri; Yoon, Suk-Jin
2016-01-01
Odyssey is a GPU-based General Relativistic Radiative Transfer (GRRT) code for computing images and/or spectra in Kerr metric describing the spacetime around a rotating black hole. Odyssey is implemented in CUDA C/C++. For flexibility, the namespace structure in C++ is used for different tasks; the two default tasks presented in the source code are the redshift of a Keplerian disk and the image of a Keplerian rotating shell at 340GHz. Odyssey_Edu, an educational software package for visualizing the ray trajectories in the Kerr spacetime that uses Odyssey, is also available.
Ray-tracing simulations of spherical Johann diffraction spectrometer for in-beam X-ray experiments
Jagodziński, P., E-mail: jagodzin@tu.kielce.pl [Department of Physics, Kielce University of Technology, Tysiaclecia PP 7, 25-314 Kielce (Poland); Pajek, M.; Banaś, D. [Institute of Physics, Jan Kochanowski University, Świȩtokrzyska 15, 25-406 Kielce (Poland); Beyer, H.F. [GSI Helmholtzzentrum für Schwerionenforschung, D-64291 Darmstadt (Germany); Trassinelli, M. [Institut des NanoSciences de Paris, Université Pierre et Marie Curie, 4 Place Jussieu, 75015 Paris (France); Stoehlker, Th. [GSI Helmholtzzentrum für Schwerionenforschung, D-64291 Darmstadt (Germany); Helmholtz-Insitut Jena, D-07743 Jena (Germany); Institut für Optic und Quantenelektronik, Friedrich-Schiller-Universität Jena, D-07743 Jena (Germany)
2014-07-01
The results of the Monte-Carlo ray-tracing simulations for a Johann-type Bragg spectrometer with spherically curved-crystal designed to detect the X-rays from a fast-moving source are reported. These calculations were performed to optimize the X-ray spectrometer to be used at the gas-target installed at ion storage ring for high-resolution X-ray experiments. In particular, the two-dimensional distributions of detected photons were studied using the Monte-Carlo method both for the stationary and moving X-ray sources, taking into account a detailed description of X-ray source and X-ray diffraction on the crystal as well as a role of the Doppler effect for in-beam experiments. The origin of the asymmetry of observed X-ray profiles was discussed in detail and the procedure to derive a precise (sub-eV) X-ray transition energy for such asymmetric profiles was proposed. The results are important for the investigations of 1s2p{sup 3}P{sub 2}→1s2s{sup 3}S{sub 1} intrashell transition in excited He-like uranium ions in in-beam X-ray experiments.
Seismic ray-tracing calculation based on parabolic travel-time interpolation
周竹生; 张赛民; 陈灵君
2004-01-01
A new seismic ray-tracing method is put forward based on parabolic travel-time interpolation(PTI) method, which is more accurate than the linear travel-time interpolation (LTI) method. Both PTI method and LTI method are used to compute seismic travel-time and ray-path in a 2-D grid cell model. Firstly, some basic concepts are introduced. The calculations of travel-time and ray-path are carried out only at cell boundaries. So, the ray-path is always straight in the same cells with uniform velocity. Two steps are applied in PTI and LTI method, step 1 computes travel-time and step 2 traces ray-path. Then, the derivation of LTI formulas is described. Because of the presence of refraction wave in shot cell, the formula aiming at shot cell is also derived. Finally, PTI method is presented. The calculation of PTI method is more complex than that of LTI method, but the error is limited. The results of numerical model show that PTI method can trace ray-path more accurately and efficiently than LTI method does.
GRay: a Massively Parallel GPU-Based Code for Ray Tracing in Relativistic Spacetimes
Chan, Chi-kwan; Ozel, Feryal
2013-01-01
We introduce GRay, a massively parallel integrator designed to trace the trajectories of billions of photons in a curved spacetime. This GPU-based integrator employs the stream processing paradigm, is implemented in CUDA C/C++, and runs on nVidia graphics cards. The peak performance of GRay using single precision floating-point arithmetic on a single GPU exceeds 300 GFLOP (or 1 nanosecond per photon per time step). For a realistic problem, where the peak performance cannot be reached, GRay is two orders of magnitude faster than existing CPU-based ray tracing codes. This performance enhancement allows more effective searches of large parameter spaces when comparing theoretical predictions of images, spectra, and lightcurves from the vicinities of compact objects to observations. GRay can also perform on-the-fly ray tracing within general relativistic magnetohydrodynamic algorithms that simulate accretion flows around compact objects. Making use of this algorithm, we calculate the properties of the shadows of K...
A boundary integral formalism for stochastic ray tracing in billiards
Chappell, David J
2014-01-01
Determining the flow of rays or particles driven by a force or velocity field is fundamental to modelling many physical processes, including weather forecasting and the simulation of molecular dynamics. High frequency wave energy distributions can also be approximated using flow or transport equations. Applications arise in underwater and room acoustics, vibro-acoustics, seismology, electromagnetics, quantum mechanics and in producing computer generated imagery. In many practical applications, the driving field is not known exactly and the dynamics are determined only up to a degree of uncertainty. This paper presents a boundary integral framework for propagating flows including uncertainties, which is shown to systematically interpolate between a deterministic and a completely random description of the trajectory propagation. A simple but efficient discretisation approach is applied to model uncertain billiard dynamics in an integrable rectangular domain.
An Energy Conservative Ray-Tracing Method With a Time Interpolation of the Force Field
Yao, Jin [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)
2015-02-10
A new algorithm that constructs a continuous force field interpolated in time is proposed for resolving existing difficulties in numerical methods for ray-tracing. This new method has improved accuracy, but with the same degree of algebraic complexity compared to Kaisers method.
A Ray-tracing Method to Analyzing Modulated Planar Fabry-Perot Antennas
Hougs, Mikkel Dahl; Kim, Oleksiy S.; Breinbjerg, Olav
2015-01-01
A new approach for fast modelling of Fabry-Perot antennas with modulated partially reflective surfaces (PRS) using ray-tracing is proposed. For validation of the method, a configuration is introduced which consists of a cavity with a modulated PRS, fed internally by a magnetic dipole. The PRS con...
Emulating Ray-Tracing Channels in Multi-probe Anechoic Chamber Setups for Virtual Drive Testing
Fan, Wei; Llorente, Ines Carton; Kyösti, Pekka
2016-01-01
This paper discusses virtual drive testing (VDT) for multiple-input multiple-output (MIMO) capable terminals in multi-probe anechoic chamber (MPAC) setups. We propose to perform VDT, via reproducing ray tracing (RT) simulated channels with the field synthesis technique. Simulation results demonst...
A Ray-tracing Method to Analyzing Modulated Planar Fabry-Perot Antennas
Hougs, Mikkel Dahl; Kim, Oleksiy S.; Breinbjerg, Olav
2015-01-01
A new approach for fast modelling of Fabry-Perot antennas with modulated partially reflective surfaces (PRS) using ray-tracing is proposed. For validation of the method, a configuration is introduced which consists of a cavity with a modulated PRS, fed internally by a magnetic dipole. The PRS...
Investigation of propagation algorithms for ray-tracing simulation of polarized neutrons
Bergbäck Knudsen, Erik; Tranum-Rømer, A.; Willendrup, Peter Kjær
2014-01-01
Ray-tracing of polarized neutrons faces a challenge when the neutron propagates through an inhomogeneous magnetic field. This affects simulations of novel instruments using encoding of energy or angle into the neutron spin. We here present a new implementation of propagation of polarized neutrons...
GPU-based ray tracing algorithm for high-speed propagation prediction in typical indoor environments
Guo, Lixin; Guan, Xiaowei; Liu, Zhongyu
2015-10-01
A fast 3-D ray tracing propagation prediction model based on virtual source tree is presented in this paper, whose theoretical foundations are geometrical optics(GO) and the uniform theory of diffraction(UTD). In terms of typical single room indoor scene, taking the geometrical and electromagnetic information into account, some acceleration techniques are adopted to raise the efficiency of the ray tracing algorithm. The simulation results indicate that the runtime of the ray tracing algorithm will sharply increase when the number of the objects in the single room is large enough. Therefore, GPU acceleration technology is used to solve that problem. As is known to all, GPU is good at calculation operation rather than logical judgment, so that tens of thousands of threads in CUDA programs are able to calculate at the same time, in order to achieve massively parallel acceleration. Finally, a typical single room with several objects is simulated by using the serial ray tracing algorithm and the parallel one respectively. It can be found easily from the results that compared with the serial algorithm, the GPU-based one can achieve greater efficiency.
A Sub-band Divided Ray Tracing Algorithm Using the DPS Subspace in UWB Indoor Scenarios
Gan, Mingming; Xu, Zhinan; Hofer, Markus
2015-01-01
Sub-band divided ray tracing (SDRT) is one technique that has been extensively used to obtain the channel characteristics for ultra-wideband (UWB) radio wave propagation in realistic indoor environments. However, the computational complexity of SDRT scales directly with the number of sub-bands. A...
Ray-tracing simulations of liquid-crystal gradient-index lenses for three-dimensional displays
Sluijter, M.; Herzog, A.; De Boer, D.K.G.; Krijn, M.P.C.M.; Urbach, P.H.
2009-01-01
For the first time, to our knowledge, we report ray-tracing simulations of an advanced liquid-crystal gradientindex lens structure for application in switchable two-dimensional/three-dimensional (3D) autostereoscopic displays. We present ray-tracing simulations of the angular-dependent lens action.
Invisibility cloaking via non-smooth transformation optics and ray tracing
Crosskey, Miles M., E-mail: mmc31@duke.ed [Mathematics Department, Duke University, Box 90320, Durham, NC 27708-0320 (United States); Nixon, Andrew T., E-mail: andrew_nixon@brown.ed [Division of Applied Mathematics, Brown University, 182 George Street, Providence, RI 02912 (United States); Schick, Leland M., E-mail: lschick@math.arizona.ed [Department of Mathematics, University of Arizona, 617 N. Santa Rita Ave., P.O. Box 210089, Tucson, AZ 85721-0089 (United States); Kovacic, Gregor, E-mail: kovacg@rpi.ed [Mathematical Sciences Department, Rensselaer Polytechnic Institute, 110 8th Street, Troy, NY 12180 (United States)
2011-05-02
We present examples of theoretically-predicted invisibility cloaks with shapes other than spheres and cylinders, including cones and ellipsoids, as well as shapes spliced from parts of these simpler shapes. In addition, we present an example explicitly displaying the non-uniqueness of invisibility cloaks of the same shape. We depict rays propagating through these example cloaks using ray tracing for geometric optics. - Highlights: Theoretically-predicted conical and ellipsoidal invisibility cloaks. Non-smooth cloaks spliced from parts of simpler shapes. Example displaying non-uniqueness of invisibility cloaks of the same shape. Rays propagating through example cloaks depicted using geometric optics.
Tichý, Vladimír; Hudec, René; Němcová, Šárka
2016-06-01
The algorithm presented is intended mainly for lobster eye optics. This type of optics (and some similar types) allows for a simplification of the classical ray-tracing procedure that requires great many rays to simulate. The method presented performs the simulation of a only few rays; therefore it is extremely effective. Moreover, to simplify the equations, a specific mathematical formalism is used. Only a few simple equations are used, therefore the program code can be simple as well. The paper also outlines how to apply the method to some other reflective optical systems.
Statistical Inverse Ray Tracing for Image-Based 3D Modeling.
Liu, Shubao; Cooper, David B
2014-10-01
This paper proposes a new formulation and solution to image-based 3D modeling (aka "multi-view stereo") based on generative statistical modeling and inference. The proposed new approach, named statistical inverse ray tracing, models and estimates the occlusion relationship accurately through optimizing a physically sound image generation model based on volumetric ray tracing. Together with geometric priors, they are put together into a Bayesian formulation known as Markov random field (MRF) model. This MRF model is different from typical MRFs used in image analysis in the sense that the ray clique, which models the ray-tracing process, consists of thousands of random variables instead of two to dozens. To handle the computational challenges associated with large clique size, an algorithm with linear computational complexity is developed by exploiting, using dynamic programming, the recursive chain structure of the ray clique. We further demonstrate the benefit of exact modeling and accurate estimation of the occlusion relationship by evaluating the proposed algorithm on several challenging data sets.
Solar Proton Transport Within an ICRU Sphere Surrounded by a Complex Shield: Ray-trace Geometry
Slaba, Tony C.; Wilson, John W.; Badavi, Francis F.; Reddell, Brandon D.; Bahadori, Amir A.
2015-01-01
A computationally efficient 3DHZETRN code with enhanced neutron and light ion (Z is less than or equal to 2) propagation was recently developed for complex, inhomogeneous shield geometry described by combinatorial objects. Comparisons were made between 3DHZETRN results and Monte Carlo (MC) simulations at locations within the combinatorial geometry, and it was shown that 3DHZETRN agrees with the MC codes to the extent they agree with each other. In the present report, the 3DHZETRN code is extended to enable analysis in ray-trace geometry. This latest extension enables the code to be used within current engineering design practices utilizing fully detailed vehicle and habitat geometries. Through convergence testing, it is shown that fidelity in an actual shield geometry can be maintained in the discrete ray-trace description by systematically increasing the number of discrete rays used. It is also shown that this fidelity is carried into transport procedures and resulting exposure quantities without sacrificing computational efficiency.
ACCELERATION RENDERING METHOD ON RAY TRACING WITH ANGLE COMPARISON AND DISTANCE COMPARISON
Liliana liliana
2007-01-01
Full Text Available In computer graphics applications, to produce realistic images, a method that is often used is ray tracing. Ray tracing does not only model local illumination but also global illumination. Local illumination count ambient, diffuse and specular effects only, but global illumination also count mirroring and transparency. Local illumination count effects from the lamp(s but global illumination count effects from other object(s too. Objects that are usually modeled are primitive objects and mesh objects. The advantage of mesh modeling is various, interesting and real-like shape. Mesh contains many primitive objects like triangle or square (rare. A problem in mesh object modeling is long rendering time. It is because every ray must be checked with a lot of triangle of the mesh. Added by ray from other objects checking, the number of ray that traced will increase. It causes the increasing of rendering time. To solve this problem, in this research, new methods are developed to make the rendering process of mesh object faster. The new methods are angle comparison and distance comparison. These methods are used to reduce the number of ray checking. The rays predicted will not intersect with the mesh, are not checked weather the ray intersects the mesh. With angle comparison, if using small angle to compare, the rendering process will be fast. This method has disadvantage, if the shape of each triangle is big, some triangles will be corrupted. If the angle to compare is bigger, mesh corruption can be avoided but the rendering time will be longer than without comparison. With distance comparison, the rendering time is less than without comparison, and no triangle will be corrupted.
Weiland, C.M. [Univ. of California, Santa Barbara, CA (United States); Steck, L.K. [Los Alamos National Lab., NM (United States); Dawson, P.B. [Geological Survey, Menlo Park, CA (United States)] [and others
1995-10-10
The authors explore the impact of three-dimensional minimum travel time ray tracing on nonlinear teleseismic inversion. This problem has particular significance when trying to image strongly contrasting low-velocity bodies, such as magma chambers, because strongly refracted/and/or diffracted rays may precede the direct P wave arrival traditionally used in straight-ray seismic tomography. They use a simplex-based ray tracer to compute the three-dimensional, minimum travel time ray paths and employ an interative technique to cope with nonlinearity. Results from synthetic data show that their algorithm results in better model reconstructions compared with traditional straight-ray inversions. The authors reexamine the teleseismic data collected at Long Valley caldera by the U.S. Geological Survey. The most prominent feature of their result is a 25-30% low-velocity zone centered at 11.5 km depth beneath the northwestern quandrant of the caldera. Beneath this at a depth of 24.5 km is a more diffuse 15% low-velocity zone. In general, the low velocities tend to deepen to the south and east. The authors interpret the shallow feature to be the residual Long Valley caldera magma chamber, while the deeper feature may represent basaltic magmas ponded in the midcrust. The deeper position of the prominent low-velocity region in comparison to earlier tomographic images is a result of using three-dimensional rays rather than straight rays in the ray tracing. The magnitude of the low-velocity anomaly is a factor of {approximately}3 times larger than earlier models from linear arrival time inversions and is consistent with models based on observations of ray bending at sites within the caldera. These results imply the presence of anywhere from 7 to 100% partial melt beneath the caldera. 40 refs., 1 fig., 1 tab.
A beam optics study of a modular multi-source X-ray tube for novel computed tomography applications
Walker, Brandon J.; Radtke, Jeff; Chen, Guang-Hong; Eliceiri, Kevin W.; Mackie, Thomas R.
2017-10-01
A modular implementation of a scanning multi-source X-ray tube is designed for the increasing number of multi-source imaging applications in computed tomography (CT). An electron beam array coupled with an oscillating magnetic deflector is proposed as a means for producing an X-ray focal spot at any position along a line. The preliminary multi-source model includes three thermionic electron guns that are deflected in tandem by a slowly varying magnetic field and pulsed according to a scanning sequence that is dependent on the intended imaging application. Particle tracking simulations with particle dynamics analysis software demonstrate that three 100 keV electron beams are laterally swept a combined distance of 15 cm over a stationary target with an oscillating magnetic field of 102 G perpendicular to the beam axis. Beam modulation is accomplished using 25 μs pulse widths to a grid electrode with a reverse gate bias of -500 V and an extraction voltage of +1000 V. Projected focal spot diameters are approximately 1 mm for 138 mA electron beams and the stationary target stays within thermal limits for the 14 kW module. This concept could be used as a research platform for investigating high-speed stationary CT scanners, for lowering dose with virtual fan beam formation, for reducing scatter radiation in cone-beam CT, or for other industrial applications.
TIM, a ray-tracing program for METATOY research and its dissemination
Lambert, Dean; Hamilton, Alasdair C.; Constable, George; Snehanshu, Harsh; Talati, Sharvil; Courtial, Johannes
2012-03-01
TIM (The Interactive METATOY) is a ray-tracing program specifically tailored towards our research in METATOYs, which are optical components that appear to be able to create wave-optically forbidden light-ray fields. For this reason, TIM possesses features not found in other ray-tracing programs. TIM can either be used interactively or by modifying the openly available source code; in both cases, it can easily be run as an applet embedded in a web page. Here we describe the basic structure of TIM's source code and how to extend it, and we give examples of how we have used TIM in our own research. Program summaryProgram title: TIM Catalogue identifier: AEKY_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEKY_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: GNU General Public License No. of lines in distributed program, including test data, etc.: 124 478 No. of bytes in distributed program, including test data, etc.: 4 120 052 Distribution format: tar.gz Programming language: Java Computer: Any computer capable of running the Java Virtual Machine (JVM) 1.6 Operating system: Any; developed under Mac OS X Version 10.6 RAM: Typically 145 MB (interactive version running under Mac OS X Version 10.6) Classification: 14, 18 External routines: JAMA [1] (source code included) Nature of problem: Visualisation of scenes that include scene objects that create wave-optically forbidden light-ray fields. Solution method: Ray tracing. Unusual features: Specifically designed to visualise wave-optically forbidden light-ray fields; can visualise ray trajectories; can visualise geometric optic transformations; can create anaglyphs (for viewing with coloured "3D glasses") and random-dot autostereograms of the scene; integrable into web pages. Running time: Problem-dependent; typically seconds for a simple scene.
Pal, Lipika R; Guda, Chittibabu
2006-11-07
The functional repertoire of the human proteome is an incremental collection of functions accomplished by protein domains evolved along the Homo sapiens lineage. Therefore, knowledge on the origin of these functionalities provides a better understanding of the domain and protein evolution in human. The lack of proper comprehension about such origin has impelled us to study the evolutionary origin of human proteome in a unique way as detailed in this study. This study reports a unique approach for understanding the evolution of human proteome by tracing the origin of its constituting domains hierarchically, along the Homo sapiens lineage. The uniqueness of this method lies in subtractive searching of functional and conserved domains in the human proteome resulting in higher efficiency of detecting their origins. From these analyses the nature of protein evolution and trends in domain evolution can be observed in the context of the entire human proteome data. The method adopted here also helps delineate the degree of divergence of functional families occurred during the course of evolution. This approach to trace the evolutionary origin of functional domains in the human proteome facilitates better understanding of their functional versatility as well as provides insights into the functionality of hypothetical proteins present in the human proteome. This work elucidates the origin of functional and conserved domains in human proteins, their distribution along the Homo sapiens lineage, occurrence frequency of different domain combinations and proteome-wide patterns of their distribution, providing insights into the evolutionary solution to the increased complexity of the human proteome.
MCViNE -- An object oriented Monte Carlo neutron ray tracing simulation package
Lin, Jiao Y Y; Granroth, Garrett E; Abernathy, Douglas L; Lumsden, Mark D; Winn, Barry; Aczel, Adam A; Aivazis, Michael; Fultz, Brent
2015-01-01
MCViNE (Monte-Carlo VIrtual Neutron Experiment) is a versatile Monte Carlo (MC) neutron ray-tracing program that provides researchers with tools for performing computer modeling and simulations that mirror real neutron scattering experiments. By adopting modern software engineering practices such as using composite and visitor design patterns for representing and accessing neutron scatterers, and using recursive algorithms for multiple scattering, MCViNE is flexible enough to handle sophisticated neutron scattering problems including, for example, neutron detection by complex detector systems, and single and multiple scattering events in a variety of samples and sample environments. In addition, MCViNE can take advantage of simulation components in linear-chain-based MC ray tracing packages widely used in instrument design and optimization, as well as NumPy-based components that make prototypes useful and easy to develop. These developments have enabled us to carry out detailed simulations of neutron scatteri...
Herlocker, J. A.; Jiang, J.; Garcia, K. J.
2008-08-01
Common digital display systems have evolved into sophisticated optical devices. The rapid market growth in liquid crystal displays makes the simulation of full systems attractive, promoting virtual prototyping with decreased development times and improved manufacturability. Realistic simulation using commercial non-sequential ray tracing tools has been instrumental in this process, but the need to accurately model polarization devices has become critical in many designs. As display systems seek more efficient use of light and more accurate color representation, the proper simulation of polarization devices with large acceptance angles is essential. This paper examines non-uniform polarization effects in the simulation of modern display devices using realistic polarizer and retarder models in the ASAPÂ® non-sequential ray-tracing environment.
Stress optical path difference analysis of off-axis lens ray trace footprint
Hsu, Ming-Ying; Chan, Chia-Yen; Lin, Wei-Cheng; Wu, Kun-Huan; Chen, Chih-Wen; Chan, Shenq-Tsong; Huang, Ting-Ming
2013-06-01
The mechanical and thermal stress on lens will cause the glass refractive index different, the refractive index of light parallel and light perpendicular to the direction of stress. The refraction index changes will introduce Optical Path Difference (OPD). This study is applying Finite Element Method (FEM) and optical ray tracing; calculate off axis ray stress OPD. The optical system stress distribution result is calculated from finite element simulation, and the stress coordinate need to rotate to optical path direction. Meanwhile, weighting stress to each optical ray path and sum the ray path OPD. The Z-direction stress OPD can be fitted by Zernike polynomial, the separated to sag difference, and rigid body motion. The fitting results can be used to evaluate the stress effect on optical component.
Guda Chittibabu
2006-11-01
Full Text Available Abstract Background The functional repertoire of the human proteome is an incremental collection of functions accomplished by protein domains evolved along the Homo sapiens lineage. Therefore, knowledge on the origin of these functionalities provides a better understanding of the domain and protein evolution in human. The lack of proper comprehension about such origin has impelled us to study the evolutionary origin of human proteome in a unique way as detailed in this study. Results This study reports a unique approach for understanding the evolution of human proteome by tracing the origin of its constituting domains hierarchically, along the Homo sapiens lineage. The uniqueness of this method lies in subtractive searching of functional and conserved domains in the human proteome resulting in higher efficiency of detecting their origins. From these analyses the nature of protein evolution and trends in domain evolution can be observed in the context of the entire human proteome data. The method adopted here also helps delineate the degree of divergence of functional families occurred during the course of evolution. Conclusion This approach to trace the evolutionary origin of functional domains in the human proteome facilitates better understanding of their functional versatility as well as provides insights into the functionality of hypothetical proteins present in the human proteome. This work elucidates the origin of functional and conserved domains in human proteins, their distribution along the Homo sapiens lineage, occurrence frequency of different domain combinations and proteome-wide patterns of their distribution, providing insights into the evolutionary solution to the increased complexity of the human proteome.
Numerical simulation and comparison of nonlinear self-focusing based on iteration and ray tracing
Li, Xiaotong; Chen, Hao; Wang, Weiwei; Ruan, Wangchao; Zhang, Luwei; Cen, Zhaofeng
2017-05-01
Self-focusing is observed in nonlinear materials owing to the interaction between laser and matter when laser beam propagates. Some of numerical simulation strategies such as the beam propagation method (BPM) based on nonlinear Schrödinger equation and ray tracing method based on Fermat's principle have applied to simulate the self-focusing process. In this paper we present an iteration nonlinear ray tracing method in that the nonlinear material is also cut into massive slices just like the existing approaches, but instead of paraxial approximation and split-step Fourier transform, a large quantity of sampled real rays are traced step by step through the system with changing refractive index and laser intensity by iteration. In this process a smooth treatment is employed to generate a laser density distribution at each slice to decrease the error caused by the under-sampling. The characteristics of this method is that the nonlinear refractive indices of the points on current slice are calculated by iteration so as to solve the problem of unknown parameters in the material caused by the causal relationship between laser intensity and nonlinear refractive index. Compared with the beam propagation method, this algorithm is more suitable for engineering application with lower time complexity, and has the calculation capacity for numerical simulation of self-focusing process in the systems including both of linear and nonlinear optical media. If the sampled rays are traced with their complex amplitudes and light paths or phases, it will be possible to simulate the superposition effects of different beam. At the end of the paper, the advantages and disadvantages of this algorithm are discussed.
Mathematic models for a ray tracing method and its applications in wireless optical communications.
Zhang, Minglun; Zhang, Yangan; Yuan, Xueguang; Zhang, Jinnan
2010-08-16
This paper presents a new ray tracing method, which contains a whole set of mathematic models, and its validity is verified by simulations. In addition, both theoretical analysis and simulation results show that the computational complexity of the method is much lower than that of previous ones. Therefore, the method can be used to rapidly calculate the impulse response of wireless optical channels for complicated systems.
Modeling pyramidal sensors in ray-tracing software by a suitable user-defined surface
Antichi, Jacopo; Munari, Matteo; Magrin, Demetrio; Riccardi, Armando
2016-04-01
Following the unprecedented results in terms of performances delivered by the first light adaptive optics system at the Large Binocular Telescope, there has been a wide-spread and increasing interest on the pyramid wavefront sensor (PWFS), which is the key component, together with the adaptive secondary mirror, of the adaptive optics (AO) module. Currently, there is no straightforward way to model a PWFS in standard sequential ray-tracing software. Common modeling strategies tend to be user-specific and, in general, are unsatisfactory for general applications. To address this problem, we have developed an approach to PWFS modeling based on user-defined surface (UDS), whose properties reside in a specific code written in C language, for the ray-tracing software ZEMAX™. With our approach, the pyramid optical component is implemented as a standard surface in ZEMAX™, exploiting its dynamic link library (DLL) conversion then greatly simplifying ray tracing and analysis. We have utilized the pyramid UDS DLL surface-referred to as pyramidal acronyms may be too risky (PAM2R)-in order to design the current PWFS-based AO system for the Giant Magellan Telescope, evaluating tolerances, with particular attention to the angular sensitivities, by means of sequential ray-tracing tools only, thus verifying PAM2R reliability and robustness. This work indicates that PAM2R makes the design of PWFS as simple as that of other optical standard components. This is particularly suitable with the advent of the extremely large telescopes era for which complexity is definitely one of the main challenges.
A rapid and accurate two-point ray tracing method in horizontally layered velocity model
TIAN Yue; CHEN Xiao-fei
2005-01-01
A rapid and accurate method for two-point ray tracing in horizontally layered velocity model is presented in this paper. Numerical experiments show that this method provides stable and rapid convergence with high accuracies, regardless of various 1-D velocity structures, takeoff angles and epicentral distances. This two-point ray tracing method is compared with the pseudobending technique and the method advanced by Kim and Baag (2002). It turns out that the method in this paper is much more efficient and accurate than the pseudobending technique, but is only applicable to 1-D velocity model. Kim(s method is equivalent to ours for cases without large takeoff angles, but it fails to work when the takeoff angle is close to 90o. On the other hand, the method presented in this paper is applicable to cases with any takeoff angles with rapid and accurate convergence. Therefore, this method is a good choice for two-point ray tracing problems in horizontally layered velocity model and is efficient enough to be applied to a wide range of seismic problems.
Vertex shading of the three-dimensional model based on ray-tracing algorithm
Hu, Xiaoming; Sang, Xinzhu; Xing, Shujun; Yan, Binbin; Wang, Kuiru; Dou, Wenhua; Xiao, Liquan
2016-10-01
Ray Tracing Algorithm is one of the research hotspots in Photorealistic Graphics. It is an important light and shadow technology in many industries with the three-dimensional (3D) structure, such as aerospace, game, video and so on. Unlike the traditional method of pixel shading based on ray tracing, a novel ray tracing algorithm is presented to color and render vertices of the 3D model directly. Rendering results are related to the degree of subdivision of the 3D model. A good light and shade effect is achieved by realizing the quad-tree data structure to get adaptive subdivision of a triangle according to the brightness difference of its vertices. The uniform grid algorithm is adopted to improve the rendering efficiency. Besides, the rendering time is independent of the screen resolution. In theory, as long as the subdivision of a model is adequate, cool effects as the same as the way of pixel shading will be obtained. Our practical application can be compromised between the efficiency and the effectiveness.
Ray-tracing and physical-optics analysis of the aperture efficiency in a radio telescope.
Olmi, Luca; Bolli, Pietro
2007-07-01
The performance of telescope systems working at microwave or visible-IR wavelengths is typically described in terms of different parameters according to the wavelength range. Most commercial ray-tracing packages have been specifically designed for use with visible-IR systems and thus, though very flexible and sophisticated, do not provide the appropriate parameters to fully describe microwave antennas and to compare with specifications. We demonstrate that the Strehl ratio is equal to the phase efficiency when the apodization factor is taken into account. The phase efficiency is the most critical contribution to the aperture efficiency of an antenna and the most difficult parameter to optimize during the telescope design. The equivalence between the Strehl ratio and the phase efficiency gives the designer/user of the telescope the opportunity to use the faster commercial ray-tracing software to optimize the design. We also discuss the results of several tests performed to check the validity of this relationship that we carried out using a ray-tracing software, ZEMAX, and a full Physical Optics software, GRASP9.3, applied to three different telescope designs that span a factor of approximately 10 in terms of D/lambda. The maximum measured discrepancy between phase efficiency and Strehl ratio varies between approximately 0.4% and 1.9% up to an offset angle of >40 beams, depending on the optical configuration, but it is always less than 0.5% where the Strehl ratio is >0.95.
MIT modular x-ray source systems for the study of plasma diagnostics
Coleman, J. W.; Wenzel, K. W.; Petrasso, R. D.; Lo, D. H.; Li, C. K.; Lierzer, J. R.; Wei, T.
1992-10-01
Two new x-ray source systems are now on line at our facility. Each provides an e-beam to 25 kV. Targets are interchangeable between machines, and four x-ray detectors may be used simultaneously with a target. The gridded e-gun of the RACEHORSE system gives a 0.5-1.0-cm pulsable spot on target. The nongridded e-gun of the SCORPION system provides a 0.3-mm or smaller dc microspot on target. RACEHORSE is being used to study and characterize type-II diamond photoconductors for use in diagnosing plasmas, while SCORPION is being used to develop a slitless spectrograph using photographic film. Source design details and some RACEHORSE results are presented.
Ray-tracing critical-angle transmission gratings for the X-ray Surveyor and Explorer-size missions
Günther, Hans M.; Bautz, Marshall W.; Heilmann, Ralf K.; Huenemoerder, David P.; Marshall, Herman L.; Nowak, Michael A.; Schulz, Norbert S.
2016-07-01
We study a critical angle transmission (CAT) grating spectrograph that delivers a spectral resolution significantly above any X-ray spectrograph ever own. This new technology will allow us to resolve kinematic components in absorption and emission lines of galactic and extragalactic matter down to unprecedented dispersion levels. We perform ray-trace simulations to characterize the performance of the spectrograph in the context of an X-ray Surveyor or Arcus like layout (two mission concepts currently under study). Our newly developed ray-trace code is a tool suite to simulate the performance of X-ray observatories. The simulator code is written in Python, because the use of a high-level scripting language allows modifications of the simulated instrument design in very few lines of code. This is especially important in the early phase of mission development, when the performances of different configurations are contrasted. To reduce the run-time and allow for simulations of a few million photons in a few minutes on a desktop computer, the simulator code uses tabulated input (from theoretical models or laboratory measurements of samples) for grating efficiencies and mirror reflectivities. We find that the grating facet alignment tolerances to maintain at least 90% of resolving power that the spectrometer has with perfect alignment are (i) translation parallel to the optical axis below 0.5 mm, (ii) rotation around the optical axis or the groove direction below a few arcminutes, and (iii) constancy of the grating period to 1:105. Translations along and rotations around the remaining axes can be significantly larger than this without impacting the performance.
Ray tracing simulation of aero-optical effect using multiple gradient index layer
Yang, Seul Ki; Seong, Sehyun; Ryu, Dongok; Kim, Sug-Whan; Kwon, Hyeuknam; Jin, Sang-Hun; Jeong, Ho; Kong, Hyun Bae; Lim, Jae Wan; Choi, Jong Hwa
2016-10-01
We present a new ray tracing simulation of aero-optical effect through anisotropic inhomogeneous media as supersonic flow field surrounds a projectile. The new method uses multiple gradient-index (GRIN) layers for construction of the anisotropic inhomogeneous media and ray tracing simulation. The cone-shaped projectile studied has 19° semi-vertical angle; a sapphire window is parallel to the cone angle; and an optical system of the projectile was assumed via paraxial optics and infrared image detector. The condition for the steady-state solver conducted through computational fluid dynamics (CFD) included Mach numbers 4 and 6 in speed, 25 km altitude, and 0° angle of attack (AoA). The grid refractive index of the flow field via CFD analysis and Gladstone-Dale relation was discretized into equally spaced layers which are parallel with the projectile's window. Each layer was modeled as a form of 2D polynomial by fitting the refractive index distribution. The light source of ray set generated 3,228 rays for varying line of sight (LOS) from 10° to 40°. Ray tracing simulation adopted the Snell's law in 3D to compute the paths of skew rays in the GRIN layers. The results show that optical path difference (OPD) and boresight error (BSE) decreases exponentially as LOS increases. The variation of refractive index decreases, as the speed of flow field increases the OPD and its rate of decay at Mach number 6 in speed has somewhat larger value than at Mach number 4 in speed. Compared with the ray equation method, at Mach number 4 and 10° LOS, the new method shows good agreement, generated 0.33% of relative root-mean-square (RMS) OPD difference and 0.22% of relative BSE difference. Moreover, the simulation time of the new method was more than 20,000 times faster than the conventional ray equation method. The technical detail of the new method and simulation is presented with results and implication.
Comparing FDTD and Ray-Tracing Models in Numerical Simulation of HgCdTe LWIR Photodetectors
Vallone, Marco; Goano, Michele; Bertazzi, Francesco; Ghione, Giovanni; Schirmacher, Wilhelm; Hanna, Stefan; Figgemeier, Heinrich
2016-09-01
We present a simulation study of HgCdTe-based long-wavelength infrared detectors, focusing on methodological comparisons between the finite-difference time-domain (FDTD) and ray-tracing optical models. We performed three-dimensional simulations to determine the absorbed photon density distributions and the corresponding photocurrent and quantum efficiency spectra of isolated n-on- p uniform-composition pixels, systematically comparing the results obtained with FDTD and ray tracing. Since ray tracing is a classical optics approach, unable to describe interference effects, its applicability has been found to be strongly wavelength dependent, especially when reflections from metallic layers are relevant. Interesting cavity effects around the material cutoff wavelength are described, and the cases where ray tracing can be considered a viable approximation are discussed.
Ray-tracing for coordinate knowledge in the JWST Integrated Science Instrument Module
Sabatke, Derek; Rohrbach, Scott; Kubalak, David
2014-01-01
Optical alignment and testing of the Integrated Science Instrument Module of the James Webb Space Telescope is underway. We describe the Optical Telescope Element Simulator used to feed the science instruments with point images of precisely known location and chief ray pointing, at appropriate wavelengths and flux levels, in vacuum and at operating temperature. The simulator's capabilities include a number of devices for in situ monitoring of source flux, wavefront error, pupil illumination, image position and chief ray angle. Taken together, these functions become a fascinating example of how the first order properties and constructs of an optical design (coordinate systems, image surface and pupil location) acquire measurable meaning in a real system. We illustrate these functions with experimental data, and describe the ray tracing system used to provide both pointing control during operation and analysis support subsequently. Prescription management takes the form of optimization and fitting. Our core too...
Betremieux, Yan
2015-01-01
Atmospheric refraction affects to various degrees exoplanet transit, lunar eclipse, as well as stellar occultation observations. Exoplanet retrieval algorithms often use analytical expressions for the column abundance along a ray traversing the atmosphere as well as for the deflection of that ray, which are first order approximations valid for low densities in a spherically symmetric homogeneous isothermal atmosphere. We derive new analytical formulae for both of these quantities, which are valid for higher densities, and use them to refine and validate a new ray tracing algorithm which can be used for arbitrary atmospheric temperature-pressure profiles. We illustrate with simple isothermal atmospheric profiles the consequences of our model for different planets: temperate Earth-like and Jovian-like planets, as well as HD189733b, and GJ1214b. We find that, for both hot exoplanets, our treatment of refraction does not make much of a difference to pressures as high as 10 atmosphere, but that it is important to ...
Ray trace algorithm description for the study of pump power absorption in double clad fibers
Narro, R.; Rodriguez, E.; Ponce, L.; de Posada, E.; Flores, T.; Arronte, M.
2011-09-01
An algorithm for the analysis of the double clad fiber design is presented. The algorithm developed in the MATLAB computing language, is based on ray tracing method applied to three-dimensional graphics figures which are composed of a set of plans. The algorithm can evaluate thousands of ray paths in sequence and its corresponding pump absorption in each of the elements of the fiber according to the Lambert-Beer law. The beam path is evaluated in 3 dimensions considering the losses by reflexion and refraction in the faces and within the fiber. Due to its flexibility, the algorithm can be used to study the ray propagation in single mode or multimode fibers, bending effects in fibers, variable geometries of the inner clad and the core, and could also be used to study tappers.
Maliage, M
2012-05-01
Full Text Available The purpose of this paper is to validate SolTrace for concentrating solar investigations at CSIR by means of a test case: the comparison of the flux distribution in the focal spot of a 1.25 m2 target aligned heliostat predicted by the ray tracing...
GRay: A Massively Parallel GPU-based Code for Ray Tracing in Relativistic Spacetimes
Chan, Chi-kwan; Psaltis, Dimitrios; Özel, Feryal
2013-11-01
We introduce GRay, a massively parallel integrator designed to trace the trajectories of billions of photons in a curved spacetime. This graphics-processing-unit (GPU)-based integrator employs the stream processing paradigm, is implemented in CUDA C/C++, and runs on nVidia graphics cards. The peak performance of GRay using single-precision floating-point arithmetic on a single GPU exceeds 300 GFLOP (or 1 ns per photon per time step). For a realistic problem, where the peak performance cannot be reached, GRay is two orders of magnitude faster than existing central-processing-unit-based ray-tracing codes. This performance enhancement allows more effective searches of large parameter spaces when comparing theoretical predictions of images, spectra, and light curves from the vicinities of compact objects to observations. GRay can also perform on-the-fly ray tracing within general relativistic magnetohydrodynamic algorithms that simulate accretion flows around compact objects. Making use of this algorithm, we calculate the properties of the shadows of Kerr black holes and the photon rings that surround them. We also provide accurate fitting formulae of their dependencies on black hole spin and observer inclination, which can be used to interpret upcoming observations of the black holes at the center of the Milky Way, as well as M87, with the Event Horizon Telescope.
Development of a total reflection X-ray fluorescence spectrometer for ultra-trace element analysis
M K Tiwari; B Gowrishankar; V K Raghuvanshi; R V Nandedkar; K J S Sawhney
2002-10-01
A simple and fairly inexpensive total reflection X-ray fluorescence (TXRF) spectrometer has been designed, constructed and realized. The spectrometer is capable of ultra-trace multielement analysis as well as performs surface characterization of thin films. The TXRF setup comprises of an X-ray generator, a slitcollimator arrangement, a monochromator/cutoff-stage, a sample reflector stage and an X-ray detection system. The glancing angle of incidence on the two reflectors is implemented using a sine-bar mechanism that enables precise angle adjustments. An energy dispersive detector and a GM counter are employed for measuring respectively the fluorescence intensities and the direct X-ray beam intensity. A Cu-target X-ray generator with its line focus window is used as an excitation source. The spectrometer is quite portable with its compact design and use of a peltier cooled solid state detector for energy dispersive detection. Alignment and characterization of the TXRF system has been performed and the minimum detection limits for various elements have been determined to be in the range of 100 pg to 5 ng even at low X-ray generator powers of 30 kV, 5 mA. The capability of the TXRF system developed for thin film characterization is also demonstrated.
A comprehensive ray tracing study on the impact of solar reflections from glass curtain walls.
Wong, Justin S J
2016-01-01
To facilitate the investigation of the impact of solar reflection from the façades of skyscrapers to surrounding environment, a comprehensive ray tracing model has been developed using the International Commerce Centre (ICC) in Hong Kong as an example. Taking into account the actual physical dimensions of buildings and meteorological data, the model simulates and traces the paths of solar reflections from ICC to the surrounding buildings, assessing the impact in terms of hit locations, light intensity and the hit time on each day throughout the year. Our analyses show that various design and architectural features of ICC have amplified the intensity of reflected solar rays and increased the hit rates of surrounding buildings. These factors include the high reflectivity of glass panels, their upward tilting angles, the concave profile of the 'Dragon Tail' (glass panels near the base), the particular location and orientation of ICC, as well as the immense height of ICC with its large reflective surfaces. The simulation results allow us to accurately map the date and time when the ray projections occur on each of the target buildings, rendering important information such as the number of converging (overlapping) projections, and the actual light intensity hitting each of the buildings at any given time. Comparisons with other skyscrapers such as Taipei 101 in Taiwan and 2-IFC (International Finance Centre) Hong Kong are made. Remedial actions for ICC and preventive measures are also discussed.
N. H. Abd Rahman
2014-01-01
Full Text Available Reflector antennas have been widely used in many areas. In the implementation of parabolic reflector antenna for broadcasting satellite applications, it is essential for the spacecraft antenna to provide precise contoured beam to effectively serve the required region. For this purpose, combinations of more than one beam are required. Therefore, a tool utilizing ray tracing method is developed to calculate precise off-axis beams for multibeam antenna system. In the multibeam system, each beam will be fed from different feed positions to allow the main beam to be radiated at the exact direction on the coverage area. Thus, detailed study on caustics of a parabolic reflector antenna is performed and presented in this paper, which is to investigate the behaviour of the rays and its relation to various antenna parameters. In order to produce accurate data for the analysis, the caustic behaviours are investigated in two distinctive modes: scanning plane and transverse plane. This paper presents the detailed discussions on the derivation of the ray tracing algorithms, the establishment of the equations of caustic loci, and the verification of the method through calculation of radiation pattern.
Spin tracking simulations in AGS based on ray-tracing methods - bare lattice, no snakes -
Meot, F.; Ahrens, L.; Gleen, J.; Huang, H.; Luccio, A.; MacKay, W. W.; Roser, T.; Tsoupas, N.
2009-09-01
This Note reports on the first simulations of and spin dynamics in the AGS using the ray-tracing code Zgoubi. It includes lattice analysis, comparisons with MAD, DA tracking, numerical calculation of depolarizing resonance strengths and comparisons with analytical models, etc. It also includes details on the setting-up of Zgoubi input data files and on the various numerical methods of concern in and available from Zgoubi. Simulations of crossing and neighboring of spin resonances in AGS ring, bare lattice, without snake, have been performed, in order to assess the capabilities of Zgoubi in that matter, and are reported here. This yields a rather long document. The two main reasons for that are, on the one hand the desire of an extended investigation of the energy span, and on the other hand a thorough comparison of Zgoubi results with analytical models as the 'thin lens' approximation, the weak resonance approximation, and the static case. Section 2 details the working hypothesis : AGS lattice data, formulae used for deriving various resonance related quantities from the ray-tracing based 'numerical experiments', etc. Section 3 gives inventories of the intrinsic and imperfection resonances together with, in a number of cases, the strengths derived from the ray-tracing. Section 4 gives the details of the numerical simulations of resonance crossing, including behavior of various quantities (closed orbit, synchrotron motion, etc.) aimed at controlling that the conditions of particle and spin motions are correct. In a similar manner Section 5 gives the details of the numerical simulations of spin motion in the static case: fixed energy in the neighboring of the resonance. In Section 6, weak resonances are explored, Zgoubi results are compared with the Fresnel integrals model. Section 7 shows the computation of the {rvec n} vector in the AGS lattice and tuning considered. Many details on the numerical conditions as data files etc. are given in the
X-rays across the galaxy population I: tracing the main sequence of star formation
Aird, J; Georgakakis, A
2016-01-01
We use deep Chandra imaging to measure the distribution of X-ray luminosities (L_X) for samples of star-forming galaxies as a function of stellar mass and redshift, using a Bayesian method to push below the nominal X-ray detection limits. Our luminosity distributions all show narrow peaks at L_X < 10^{42} erg/s that we associate with star formation, as opposed to AGN that are traced by a broad tail to higher L_X. Tracking the luminosity of these peaks as a function of stellar mass reveals an "X-ray main sequence" with a constant slope ~0.63 +/- 0.03 over 8.5 < log M*/Msun < 11.5 and 0.1 < z < 4, with a normalization that increases with redshift as (1+z)^{3.79+/-0.12}. We also compare the peak X-ray luminosities with UV-to-IR tracers of star formation rates (SFRs) to calibrate the scaling between L_X and SFR. We find that L_X \\propto SFR^{0.83} x (1+z)^{1.3}, where the redshift evolution and non-linearity likely reflect changes in high-mass X-ray binary populations of star-forming galaxies. Usin...
Infrasonic ray tracing applied to mesoscale atmospheric structures: refraction by hurricanes.
Bedard, Alfred J; Jones, R Michael
2013-11-01
A ray-tracing program is used to estimate the refraction of infrasound by the temperature structure of the atmosphere and by hurricanes represented by a Rankine-combined vortex wind plus a temperature perturbation. Refraction by the hurricane winds is significant, giving rise to regions of focusing, defocusing, and virtual sources. The refraction of infrasound by the temperature anomaly associated with a hurricane is small, probably no larger than that from uncertainties in the wind field. The results are pertinent to interpreting ocean wave generated infrasound in the vicinities of tropical cyclones.
Shi, Guangyuan; Li, Song; Huang, Ke; Li, Zile; Zheng, Guoxing
2016-10-01
We have developed a new numerical ray-tracing approach for LIDAR signal power function computation, in which the light round-trip propagation is analyzed by geometrical optics and a simple experiment is employed to acquire the laser intensity distribution. It is relatively more accurate and flexible than previous methods. We emphatically discuss the relationship between the inclined angle and the dynamic range of detector output signal in biaxial LIDAR system. Results indicate that an appropriate negative angle can compress the signal dynamic range. This technique has been successfully proved by comparison with real measurements.
X-Ray fluorescence analysis of trace elements in fruit juice
Bao, Sheng-Xiang; Wang, Zhi-Hong; Liu, Jing-Song
1999-12-01
X-Ray fluorescence spectrometry is applied to the determination of trace elements in fruit juice characterized by a high content of sugar and other soluble solid substances. Samples are prepared by evaporation, carbonization and pressing into discs. The synthesis of standards is described in detail. All element concentrations are directly estimated from linear calibration curves obtained without any matrix correction. The results of the analysis are in good agreement with those given by inductively coupled plasma-atomic emission spectrometry and atomic absorption spectrometry techniques.
Mitsuishi, I.; Ezoe, Y.; Ogawa, T.; Sato, M.; Nakamura, K.; Numazawa, M.; Takeuchi, K.; Ohashi, T.; Ishikawa, K.; Mitsuda, K.
2016-01-01
To investigate a feasibility for in situ X-ray imaging spectrometer JUXTA (Jupiter X-ray Telescope Array) onboard a Japanese Jupiter exploration mission, we demonstrated the ideal performances, i.e., angular resolution, effective area and grasp, of our original, conically-approximated Wolter type-I MEMS-processed optics, by extending the previous ray-tracing simulator. The novel simulator enables us to study both on- and off-axis responses for our optics with two-stage optical configurations for the first time. The on-axis angular resolution is restricted to ∼ 13 μm corresponding to ∼ 10 arcsec on the detector plane without considering the diffraction effect and dominated by the diffraction effect below ∼ 1 keV (e.g., 13 arcsec at 1 keV). Si optics can achieve effective area of >700 mm2 and grasp of >1600 mm2 deg2 at our interesting energy of 600 eV. Larger effective area and grasp can be attained by employing Ni as a substrate material or Ir as a reflecting surface material. However, other factors produced in the fabrication processes such as the waviness on the mirror surface and the deformation error cause the significant performance degradation. Thus, we concluded that MEMS-processed optics can satisfy all the requirements of JUXTA only if the manufacturing accuracy can be controlled.
Zijffers, J.F.; Janssen, M.G.J.; Tramper, J.; Wijffels, R.H.; Salim, S.
2008-01-01
The Green Solar Collector (GSC), a photobioreactor designed for area efficient outdoor cultivation of microalgae uses Fresnel lenses and light guides to focus, transport and distribute direct light into the algae suspension. Calculating the path of rays of light, so-called ray tracing, is used to de
Snellenburg, J.J.; Braaf, B.; Hermans, E.A.; Heijde, van der R.G.L.; Sicam, V.A.
2010-01-01
A forward ray tracing (FRT) model is presented to determine the exact image projection in a general corneal topography system. Consequently, the skew ray error in Placido-based topography is demonstrated. A quantitative analysis comparing FRT-based algorithms and Placido-based algorithms in reconstr
Zijffers, J.F.; Janssen, M.G.J.; Tramper, J.; Wijffels, R.H.; Salim, S.
2008-01-01
The Green Solar Collector (GSC), a photobioreactor designed for area efficient outdoor cultivation of microalgae uses Fresnel lenses and light guides to focus, transport and distribute direct light into the algae suspension. Calculating the path of rays of light, so-called ray tracing, is used to de
Modeling of 3D In—Building Propagation by Ray Tracing Technique
GongKe; XuRui
1995-01-01
The modeling of in-building propagation is of great importance for planning of indoor wireless networks.To model the transmission system comprising of transmitter,receiver and dif-ferent kinds of obstacles,ray tracing technique is used by taking a transmitter as a source launch-ing radio rays in different directions,some of these can reach the receiver through different paths with different path loss and delay,adding them together gives out the field strength at the receiv-ing point.Based on this model,computer simulation is carried out to predict the propagation loss and delay spread,it is shown that the simulation agrees well with the experiments.
Novel applications of the x-ray tracing software package McXtrace
Bergbäck Knudsen, Erik; Nielsen, Martin Meedom; Haldrup, Kristoffer
2014-01-01
We will present examples of applying the X-ray tracing software package McXtrace to different kinds of X-ray scattering experiments. In particular we will be focusing on time-resolved type experiments. Simulations of full scale experiments are particularly useful for this kind, especially when...... some of the issues encountered. Generally more than one or all of these effects are present at once. Simulations can in these cases be used to identify distinct footprints of such distortions and thus give the experimenter a means of deconvoluting them from the signal. We will present a study...... of this kind along with the newest developments of the McXtrace software package....
Ray-tracing analysis of crosstalk in multi-core polymer optical fibers.
Berganza, Amaia; Aldabaldetreku, Gotzon; Zubia, Joseba; Durana, Gaizka
2010-10-11
The aim of this paper is to present a new ray-tracing model which describes the propagation of light in multi-core polymer optical fibers (MCPOFs), taking into account the crosstalk among their cores. The new model overcomes many of the limitations of previous approaches allowing us to simulate MCPOFs of arbitrary designs. Additionally, it provides us with the output ray distribution at the end of the fiber, making it possible to calculate useful parameters related to the fiber performance such as the Near-Field Pattern, the Far-Field Pattern or the bandwidth. We also present experimental measurements in order to validate the computational model and we analyze the importance of crosstalk in different MCPOF configurations.
Microcellular propagation prediction model based on an improved ray tracing algorithm.
Liu, Z-Y; Guo, L-X; Fan, T-Q
2013-11-01
Two-dimensional (2D)/two-and-one-half-dimensional ray tracing (RT) algorithms for the use of the uniform theory of diffraction and geometrical optics are widely used for channel prediction in urban microcellular environments because of their high efficiency and reliable prediction accuracy. In this study, an improved RT algorithm based on the "orientation face set" concept and on the improved 2D polar sweep algorithm is proposed. The goal is to accelerate point-to-point prediction, thereby making RT prediction attractive and convenient. In addition, the use of threshold control of each ray path and the handling of visible grid points for reflection and diffraction sources are adopted, resulting in an improved efficiency of coverage prediction over large areas. Measured results and computed predictions are also compared for urban scenarios. The results indicate that the proposed prediction model works well and is a useful tool for microcellular communication applications.
Photorealistic ray tracing of free-space invisibility cloaks made of uniaxial dielectrics
Halimeh, Jad C
2012-01-01
The design rules of transformation optics generally lead to spatially inhomogeneous and anisotropic impedance-matched magneto-dielectric material distributions for, e.g., free-space invisibility cloaks. Recently, simplified anisotropic non-magnetic free-space cloaks made of a locally uniaxial dielectric material (calcite) have been realized experimentally. In a two-dimensional setting and for in-plane polarized light propagating in this plane, the cloaking performance can still be perfect for light rays. However, for general views in three dimensions, various imperfections are expected. In this paper, we study two different purely dielectric uniaxial cylindrical free-space cloaks. For one, the optic axis is along the radial direction, for the other one it is along the azimuthal direction. The azimuthal uniaxial cloak has not been suggested previously to the best of our knowledge. We visualize the cloaking performance of both by calculating photorealistic images rendered by ray tracing. Following and complemen...
Tracing X-rays through an L-shaped laterally graded multilayer mirror: a synchrotron application.
Honnicke, Marcelo Goncalves; Huang, Xianrong; Keister, Jeffrey W; Kodituwakku, Chaminda Nalaka; Cai, Yong Q
2010-05-01
A theoretical model to trace X-rays through an L-shaped (nested or Montel Kirkpatrick-Baez mirrors) laterally graded multilayer mirror to be used in a synchrotron application is presented. The model includes source parameters (size and divergence), mirror figure (parabolic and elliptic), multilayer parameters (reflectivity, which depends on layer material, thickness and number of layers) and figure errors (slope error, roughness, layer thickness fluctuation Deltad/d and imperfection in the corners). The model was implemented through MATLAB/OCTAVE scripts, and was employed to study the performance of a multilayer mirror designed for the analyzer system of an ultrahigh-resolution inelastic X-ray scattering spectrometer at National Synchrotron Light Source II. The results are presented and discussed.
Integrated ray tracing simulation of spectral bio-signatures from full 3D earth model
Ryu, Dongok; Seong, Sehyun; Lee, Jae-Min; Hong, Jinsuk; Jeong, Soomin; Jeong, Yukyeong; Kim, Sug-Whan
2009-08-01
Accurate identification and understanding of spectral bio-signatures from possible extra terrestrial planets have received an ever increasing attention from both astronomy and space science communities in recent years. In pursuance of this subject, one of the most important scientific breakthroughs would be to obtain the detailed understanding on spectral biosignatures of the Earth, as it serves as a reference datum for accurate interpretation of collapsed (in temporal and spatial domains) information from the spectral measurement using TPF instruments. We report a new Integrated Ray Tracing (IRT) model capable of computing various spectral bio-signatures as they are observed from the Earth surface. The model includes the Sun, the full 3-D Earth, and an optical instrument, all combined into single ray tracing environment in real scale. In particular, the full 3-D Earth surface is constructed from high resolution coastal line data and defined with realistic reflectance and BSDF characteristics depending on wavelength, vegetation types and their distributions. We first examined the model validity by confirming the imaging and radiometric performance of the AmonRa visible channel camera, simulating the Earth observation from the L1 halo orbit. We then computed disk averaged spectra, light curves and NDVI indexes, leading to the construction of the observed disk averaged spectra at the AmonRa instrument detector plane. The model, computational procedure and the simulation results are presented. The future plan for the detailed spectral signature simulation runs for various input conditions including seasonal vegetation changes and variable cloud covers is discussed.
MCViNE - An object oriented Monte Carlo neutron ray tracing simulation package
Lin, Jiao Y. Y.; Smith, Hillary L.; Granroth, Garrett E.; Abernathy, Douglas L.; Lumsden, Mark D.; Winn, Barry; Aczel, Adam A.; Aivazis, Michael; Fultz, Brent
2016-02-01
MCViNE (Monte-Carlo VIrtual Neutron Experiment) is an open-source Monte Carlo (MC) neutron ray-tracing software for performing computer modeling and simulations that mirror real neutron scattering experiments. We exploited the close similarity between how instrument components are designed and operated and how such components can be modeled in software. For example we used object oriented programming concepts for representing neutron scatterers and detector systems, and recursive algorithms for implementing multiple scattering. Combining these features together in MCViNE allows one to handle sophisticated neutron scattering problems in modern instruments, including, for example, neutron detection by complex detector systems, and single and multiple scattering events in a variety of samples and sample environments. In addition, MCViNE can use simulation components from linear-chain-based MC ray tracing packages which facilitates porting instrument models from those codes. Furthermore it allows for components written solely in Python, which expedites prototyping of new components. These developments have enabled detailed simulations of neutron scattering experiments, with non-trivial samples, for time-of-flight inelastic instruments at the Spallation Neutron Source. Examples of such simulations for powder and single-crystal samples with various scattering kernels, including kernels for phonon and magnon scattering, are presented. With simulations that closely reproduce experimental results, scattering mechanisms can be turned on and off to determine how they contribute to the measured scattering intensities, improving our understanding of the underlying physics.
Fast ray-tracing of human eye optics on Graphics Processing Units.
Wei, Qi; Patkar, Saket; Pai, Dinesh K
2014-05-01
We present a new technique for simulating retinal image formation by tracing a large number of rays from objects in three dimensions as they pass through the optic apparatus of the eye to objects. Simulating human optics is useful for understanding basic questions of vision science and for studying vision defects and their corrections. Because of the complexity of computing such simulations accurately, most previous efforts used simplified analytical models of the normal eye. This makes them less effective in modeling vision disorders associated with abnormal shapes of the ocular structures which are hard to be precisely represented by analytical surfaces. We have developed a computer simulator that can simulate ocular structures of arbitrary shapes, for instance represented by polygon meshes. Topographic and geometric measurements of the cornea, lens, and retina from keratometer or medical imaging data can be integrated for individualized examination. We utilize parallel processing using modern Graphics Processing Units (GPUs) to efficiently compute retinal images by tracing millions of rays. A stable retinal image can be generated within minutes. We simulated depth-of-field, accommodation, chromatic aberrations, as well as astigmatism and correction. We also show application of the technique in patient specific vision correction by incorporating geometric models of the orbit reconstructed from clinical medical images. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.
Monte Carlo tolerancing tool using nonsequential ray tracing on a computer cluster
Reimer, Christopher
2010-08-01
The development of a flexible tolerancing tool for illumination systems based on Matlab® and Zemax® is described in this paper. Two computationally intensive techniques are combined, Monte Carlo tolerancing and non-sequential ray tracing. Implementation of the tool on a computer cluster allows for relatively rapid tolerancing. This paper explores the tool structure, describing the splitting the task of tolerancing between Zemax and Matlab. An equation is derived that determines the number of simulated ray traces needed to accurately resolve illumination uniformity. Two examples of tolerancing illuminators are given. The first one is a projection system consisting of a pico-DLP, a light pipe, a TIR prism and the critical illumination relay optics. The second is a wide band, high performance Köhler illuminator, which includes a modified molded LED as the light source. As high performance illumination systems evolve, the practice of applying standard workshop tolerances to these systems may need to be re-examined.
Kjartansson, Einar; Bjarnason, Ingi Th.
2017-04-01
Tools for ray-tracing through one dimensional earth models consisting of layers of constant velocity gradients, and continuous values across layers, have been developed. They are used to investigate stability and robustness of earthquake locations and velocity determinations in the South Iceland Lowlands (SIL) a transform seismic zone. These tools will also be used to invert for velocity functions for different regions and time periods, by inverting simultaneously for micro-earthquake source parameters and P and S velocities. Increase of velocity gradient with depth will cause rays with different take-off angles to cross, which can result in focusing and triplication when velocity is plotted versus time. It is therefore important to constrain the velocity solutions to avoid this. Large changes in gradient between adjacent layers causes variability of ray density and geometrical spreading, particularly for rays that turn just below the boundaries. This may create artificial clustering in the depth distribution of micro-earthquake source solutions. Resampling of the velocity functions using cubic spline interpolation can be used to reduce these effects. The software is open source and can be accessed at https://github.com/4dseismic
Ray tracing based path-length calculations for polarized light tomographic imaging
Manjappa, Rakesh; Kanhirodan, Rajan
2015-09-01
A ray tracing based path length calculation is investigated for polarized light transport in a pixel space. Tomographic imaging using polarized light transport is promising for applications in optical projection tomography of small animal imaging and turbid media with low scattering. Polarized light transport through a medium can have complex effects due to interactions such as optical rotation of linearly polarized light, birefringence, di-attenuation and interior refraction. Here we investigate the effects of refraction of polarized light in a non-scattering medium. This step is used to obtain the initial absorption estimate. This estimate can be used as prior in Monte Carlo (MC) program that simulates the transport of polarized light through a scattering medium to assist in faster convergence of the final estimate. The reflectance for p-polarized (parallel) and s-polarized (perpendicular) are different and hence there is a difference in the intensities that reach the detector end. The algorithm computes the length of the ray in each pixel along the refracted path and this is used to build the weight matrix. This weight matrix with corrected ray path length and the resultant intensity reaching the detector for each ray is used in the algebraic reconstruction (ART) method. The proposed method is tested with numerical phantoms for various noise levels. The refraction errors due to regions of different refractive index are discussed, the difference in intensities with polarization is considered. The improvements in reconstruction using the correction so applied is presented. This is achieved by tracking the path of the ray as well as the intensity of the ray as it traverses through the medium.
Identification of gravity wave sources using reverse ray tracing over Indian region
M. Pramitha
2014-07-01
Full Text Available Reverse ray tracing method is successfully implemented for the first time in the Indian region for identification of the sources and propagation characteristics of the gravity waves observed using airglow emissions from Gadanki (13.5° N, 79.2° E and Hyderabad (17.5° N, 78.5° E. Wave amplitudes are also traced back for these wave events by including both radiative and diffusive damping. Background temperature and wind data obtained from MSISE-90 and HWM-07 models, respectively, are used for the ray tracing. For Gadanki region suitability of these models is tested. Further, a climatological model of background atmosphere for Gadanki region has been developed using a long-term of nearly 30 years of observations available from a variety of ground-based (MST radar, radiosonde, MF radar, rocket-, and satellite-borne measurements. For considering real-time atmospheric inputs, ERA-Interim products are utilized. By this reverse ray method, the source locations for nine wave events could be identified to be in the upper troposphere, whereas, for five other events the waves seem to have been ducted in the mesosphere itself. Uncertainty in locating the terminal points in the horizontal direction is estimated to be within 50–100 and 150–300 km for Gadanki and Hyderabad wave events, respectively. This uncertainty arises mainly due to non-consideration of the day-to-day variability in tidal amplitudes. As no convection in-and-around the terminal points are noticed, it is unlikely to be the source. Interestingly, large (~9 m s−1 km−1 vertical shear in the horizontal wind is noted near the ray terminal points (at 10–12 km altitude and is identified to be the source for generating the nine wave events. Conditions prevailing at the terminal points for each of the 14 events are also provided. These events provide leads to a greater understanding of the tropical lower and upper atmospheric coupling through gravity waves.
Okumura, Akira; Rulten, Cameron
2016-01-01
We have developed a non-sequential ray-tracing simulation library, ROOT-based simulator for ray tracing (ROBAST), which is aimed to be widely used in optical simulations of cosmic-ray (CR) and gamma-ray telescopes. The library is written in C++, and fully utilizes the geometry library of the ROOT framework. Despite the importance of optics simulations in CR experiments, no open-source software for ray-tracing simulations that can be widely used in the community has existed. To reduce the dispensable effort needed to develop multiple ray-tracing simulators by different research groups, we have successfully used ROBAST for many years to perform optics simulations for the Cherenkov Telescope Array (CTA). Among the six proposed telescope designs for CTA, ROBAST is currently used for three telescopes: a Schwarzschild-Couder (SC) medium-sized telescope, one of SC small-sized telescopes, and a large-sized telescope (LST). ROBAST is also used for the simulation and development of hexagonal light concentrators propose...
GPU-based four-dimensional general-relativistic ray tracing
Kuchelmeister, Daniel; Müller, Thomas; Ament, Marco; Wunner, Günter; Weiskopf, Daniel
2012-10-01
This paper presents a new general-relativistic ray tracer that enables image synthesis on an interactive basis by exploiting the performance of graphics processing units (GPUs). The application is capable of visualizing the distortion of the stellar background as well as trajectories of moving astronomical objects orbiting a compact mass. Its source code includes metric definitions for the Schwarzschild and Kerr spacetimes that can be easily extended to other metric definitions, relying on its object-oriented design. The basic functionality features a scene description interface based on the scripting language Lua, real-time image output, and the ability to edit almost every parameter at runtime. The ray tracing code itself is implemented for parallel execution on the GPU using NVidia's Compute Unified Device Architecture (CUDA), which leads to performance improvement of an order of magnitude compared to a single CPU and makes the application competitive with small CPU cluster architectures. Program summary Program title: GpuRay4D Catalog identifier: AEMV_v1_0 Program summary URL: http://cpc.cs.qub.ac.uk/summaries/AEMV_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 73649 No. of bytes in distributed program, including test data, etc.: 1334251 Distribution format: tar.gz Programming language: C++, CUDA. Computer: Linux platforms with a NVidia CUDA enabled GPU (Compute Capability 1.3 or higher), C++ compiler, NVCC (The CUDA Compiler Driver). Operating system: Linux. RAM: 2 GB Classification: 1.5. External routines: OpenGL Utility Toolkit development files, NVidia CUDA Toolkit 3.2, Lua5.2 Nature of problem: Ray tracing in four-dimensional Lorentzian spacetimes. Solution method: Numerical integration of light rays, GPU-based parallel programming using CUDA, 3D
Zhang, Dong; Zhang, Ting-Ting; Zhang, Xiao-Lei; Yang, Yan; Hu, Ying; Qin, Qian-Qing
2013-05-01
We present a new method of three-dimensional (3-D) seismic ray tracing, based on an improvement to the linear traveltime interpolation (LTI) ray tracing algorithm. This new technique involves two separate steps. The first involves a forward calculation based on the LTI method and the dynamic successive partitioning scheme, which is applied to calculate traveltimes on cell boundaries and assumes a wavefront that expands from the source to all grid nodes in the computational domain. We locate several dynamic successive partition points on a cell's surface, the traveltimes of which can be calculated by linear interpolation between the vertices of the cell's boundary. The second is a backward step that uses Fermat's principle and the fact that the ray path is always perpendicular to the wavefront and follows the negative traveltime gradient. In this process, the first-arriving ray path can be traced from the receiver to the source along the negative traveltime gradient, which can be calculated by reconstructing the continuous traveltime field with cubic B-spline interpolation. This new 3-D ray tracing method is compared with the LTI method and the shortest path method (SPM) through a number of numerical experiments. These comparisons show obvious improvements to computed traveltimes and ray paths, both in precision and computational efficiency.
,
2015-01-01
We have developed a non-sequential ray-tracing simulation library, ROot-BAsed Simulator for ray Tracing (ROBAST), which is aimed for wide use in optical simulations of cosmic-ray (CR) and gamma-ray telescopes. The library is written in C++ and fully utilizes the geometry library of the ROOT analysis framework. Despite the importance of optics simulations in CR experiments, no open-source software for ray-tracing simulations that can be widely used existed. To reduce the unnecessary effort demanded when different research groups develop multiple ray-tracing simulators, we have successfully used ROBAST for many years to perform optics simulations for the Cherenkov Telescope Array (CTA). Among the proposed telescope designs for CTA, ROBAST is currently being used for three telescopes: a Schwarzschild--Couder telescope, one of the Schwarzschild--Couder small-sized telescopes, and a large-sized telescope (LST). ROBAST is also used for the simulations and the development of hexagonal light concentrators that has be...
X-rays across the galaxy population - I. Tracing the main sequence of star formation
Aird, J.; Coil, A. L.; Georgakakis, A.
2017-03-01
We use deep Chandra imaging to measure the distribution of X-ray luminosities (LX) for samples of star-forming galaxies as a function of stellar mass and redshift, using a Bayesian method to push below the nominal X-ray detection limits. Our luminosity distributions all show narrow peaks at LX ≲ 1042 erg s-1 that we associate with star formation, as opposed to AGN that are traced by a broad tail to higher LX. Tracking the luminosity of these peaks as a function of stellar mass reveals an 'X-ray main sequence' with a constant slope ≈0.63 ± 0.03 over 8.5 ≲ log {M}_{ast }/M_{⊙} ≲ 11.5 and 0.1 ≲ z ≲ 4, with a normalization that increases with redshift as (1 + z)3.79 ± 0.12. We also compare the peak X-ray luminosities with UV-to-IR tracers of star formation rates (SFRs) to calibrate the scaling between LX and SFR. We find that LX ∝ SFR0.83 × (1 + z)1.3, where the redshift evolution and non-linearity likely reflect changes in high-mass X-ray binary populations of star-forming galaxies. Using galaxies with a broader range of SFR, we also constrain a stellar-mass-dependent contribution to LX, likely related to low-mass X-ray binaries. Using this calibration, we convert our X-ray main sequence to SFRs and measure a star-forming main sequence with a constant slope ≈0.76 ± 0.06 and a normalization that evolves with redshift as (1 + z)2.95 ± 0.33. Based on the X-ray emission, there is no evidence for a break in the main sequence at high stellar masses, although we cannot rule out a turnover given the uncertainties in the scaling of LX to SFR.
KARAT-LAMBDA - frequency dependent ray-traced troposphere delays for space applications
Hobiger, Thomas; Baron, Philippe
2014-05-01
Space-geodetic microwave techniques work under the assumption that the only dispersive, i.e. frequency dependent delay contribution is caused by the ionosphere. In general, the refractivity, even for the troposphere, is a complex quantity which can be denoted as N = N0 + (N'(f) + i N''(f)) where N0 is a frequency independent term, and N'(f) and N''(f) represent the complex frequency dependence. Thereby, the imaginary part can be used to derive the loss of energy (absorption) and the real part can be assigned to the changes in the propagation velocity (refraction) and thus describes the delay of an electromagnetic wave which propagates through that medium. Although the frequency dependent delay contribution appears to be of small order, one has to consider that signals are propagating through few kilometers of troposphere at high elevations to hundredths of kilometers at low elevations. Therefore, the Kashima Ray-Tracing package (Hobiger et al., 2008) has been modified (and named KARAT-LAMBDA) to enable the consideration of a frequency dependent refractivity. By using this tool, it was studied if and to which extent future space geodetic instruments are affected from dispersive troposphere delays. Moreover, a semi-empirical correction model for the microwave link of the Atomic Clock Ensemble in Space (ACES) has been developed, based on ray-tracing calculations with KARAT-LAMBDA. The proposed model (Hobiger et al., 2013) has been tested with simulated ISS overflights at different potential ACES ground station sites and it could be demonstrated that this model is capable to remove biases and elevation dependent features caused by the dispersive troposphere delay difference between the up-link and down-link. References: T. Hobiger, R. Ichikawa, T. Kondo, and Y. Koyama (2008), Fast and accurate ray-tracing algorithms for real-time space geodetic applications using numerical weather models, Journal of Geophysical Research, vol. 113, iss. D203027, pp. 1-14. T. Hobiger, D
Determination of minor and trace elements in kidney stones by x-ray fluorescence analysis
Srivastava, Anjali; Heisinger, Brianne J.; Sinha, Vaibhav; Lee, Hyong-Koo; Liu, Xin; Qu, Mingliang; Duan, Xinhui; Leng, Shuai; McCollough, Cynthia H.
2014-03-01
The determination of accurate material composition of a kidney stone is crucial for understanding the formation of the kidney stone as well as for preventive therapeutic strategies. Radiations probing instrumental activation analysis techniques are excellent tools for identification of involved materials present in the kidney stone. In particular, x-ray fluorescence (XRF) can be very useful for the determination of minor and trace materials in the kidney stone. The X-ray fluorescence measurements were performed at the Radiation Measurements and Spectroscopy Laboratory (RMSL) of department of nuclear engineering of Missouri University of Science and Technology and different kidney stones were acquired from the Mayo Clinic, Rochester, Minnesota. Presently, experimental studies in conjunction with analytical techniques were used to determine the exact composition of the kidney stone. A new type of experimental set-up was developed and utilized for XRF analysis of the kidney stone. The correlation of applied radiation source intensity, emission of X-ray spectrum from involving elements and absorption coefficient characteristics were analyzed. To verify the experimental results with analytical calculation, several sets of kidney stones were analyzed using XRF technique. The elements which were identified from this techniques are Silver (Ag), Arsenic (As), Bromine (Br), Chromium (Cr), Copper (Cu), Gallium (Ga), Germanium (Ge), Molybdenum (Mo), Niobium (Nb), Rubidium (Rb), Selenium (Se), Strontium (Sr), Yttrium (Y), Zirconium (Zr). This paper presents a new approach for exact detection of accurate material composition of kidney stone materials using XRF instrumental activation analysis technique.
Avlonitis, Viktor; Hsuan, Juliana
2015-01-01
The purpose of this research is to investigate the studies on service modularity with a goal of informing service science and advancing contemporary service systems research. Modularity, a general systems property, can add theoretical underpinnings to the conceptual development of service science...... in general and service systems in particular. Our research is guided by the following question: how can modularity theory inform service system design? We present a review of the modularity literature and associated concepts. We then introduce the contemporary service science and service system discourse...
Yang, Yufei; Yan, Changxiang
2016-02-20
The polarization properties of a two-axis periscopic optical scanner constituted by a pair of rotating planar mirrors have been studied by using the three-dimensional polarization ray-tracing matrix method. The separate and cumulative matrices that define the transformation of the polarization state are obtained and expressed in terms of the rotation angles of two mirrors. The variations of diattenuation and retardance are investigated and graphically shown as functions of the rotation angles. On this basis, a further investigation about the cumulative polarization aberrations of three different metal-coated periscopic scanners is accomplished. Finally, the output polarization states of the three metal-coated scanners are calculated with the input beam of the arbitrary polarization states, and the results show that aluminum film is more appropriate than gold film or silver film for the polarization-maintaining periscopic scanner.
Oprea, Cristiana; Gustova, Marina V; Oprea, Ioan A; Buzguta, Violeta L
2014-01-01
X-ray fluorescence spectrometry (XRFS) was used as a multielement method of evaluation of individual whole human tooth or tooth tissues for their amounts of trace elements. Measurements were carried out on human enamel, dentine, and dental cementum, and some differences in tooth matrix composition were noted. In addition, the elemental concentrations determined in teeth from subjects of different ages, nutritional states, professions and gender, living under various environmental conditions and dietary habits, were included in a comparison by multivariate statistical analysis (MVSA) methods. By factor analysis it was established that inorganic components of human teeth varied consistently with their source in the tissue, with more in such tissue from females than in that from males, and more in tooth incisor than in tooth molar.
MC ray-tracing optimization of lobster-eye focusing devices with RESTRAX
Saroun, Jan [Nuclear Physics Institute, ASCR, 25068 Rez (Czech Republic)]. E-mail: saroun@ujf.cas.cz; Kulda, Jiri [Institut Laue-Langevin, 6 rue Jules Horowitz, BP 156, 38042 Grenoble Cedex 9 (France)
2006-11-15
The enhanced functionalities of the latest version of the RESTRAX software, providing a high-speed Monte Carlo (MC) ray-tracing code to represent a virtual three-axis neutron spectrometer, include representation of parabolic and elliptic guide profiles and facilities for numerical optimization of parameter values, characterizing the instrument components. As examples, we present simulations of a doubly focusing monochromator in combination with cold neutron guides and lobster-eye supermirror devices, concentrating a monochromatic beam to small sample volumes. A Levenberg-Marquardt minimization algorithm is used to optimize simultaneously several parameters of the monochromator and lobster-eye guides. We compare the performance of optimized configurations in terms of monochromatic neutron flux and energy spread and demonstrate the effect of lobster-eye optics on beam transformations in real and momentum subspaces.
Simulation of radiation damping in rings, using stepwise ray-tracing methods
Méot, F.
2015-06-01
The ray-tracing code Zgoubi computes particle trajectories in arbitrary magnetic and/or electric field maps or analytical field models. It includes a built-in fitting procedure, spin tracking, many Monte Carlo processes. The accuracy of the integration method makes it an efficient tool for multi-turn tracking in periodic machines. Energy loss by synchrotron radiation, based on Monte Carlo techniques, had been introduced in Zgoubi in the early 2000s for studies regarding the linear collider beam delivery system. However, only recently has this Monte Carlo tool been used for systematic beam dynamics and spin diffusion studies in rings, including the eRHIC electron-ion collider project at the Brookhaven National Laboratory. Some beam dynamics aspects of this recent use of Zgoubi capabilities, including considerations of accuracy as well as further benchmarking in the presence of synchrotron radiation in rings, are reported here.
Heat-Flux Analysis of Solar Furnace Using the Monte Carlo Ray-Tracing Method
Lee, Hyun Jin; Kim, Jong Kyu; Lee, Sang Nam; Kang, Yong Heack [Korea Institute of Energy Research, Daejeon (Korea, Republic of)
2011-10-15
An understanding of the concentrated solar flux is critical for the analysis and design of solar-energy-utilization systems. The current work focuses on the development of an algorithm that uses the Monte Carlo ray-tracing method with excellent flexibility and expandability; this method considers both solar limb darkening and the surface slope error of reflectors, thereby analyzing the solar flux. A comparison of the modeling results with measurements at the solar furnace in Korea Institute of Energy Research (KIER) show good agreement within a measurement uncertainty of 10%. The model evaluates the concentration performance of the KIER solar furnace with a tracking accuracy of 2 mrad and a maximum attainable concentration ratio of 4400 sun. Flux variations according to measurement position and flux distributions depending on acceptance angles provide detailed information for the design of chemical reactors or secondary concentrators.
Enzo+Moray: Radiation Hydrodynamics Adaptive Mesh Refinement Simulations with Adaptive Ray Tracing
Wise, John H
2010-01-01
We describe a photon-conserving radiative transfer algorithm, using a spatially-adaptive ray tracing scheme, and its parallel implementation into the adaptive mesh refinement (AMR) cosmological hydrodynamics code, Enzo. By coupling the solver with the energy equation and non-equilibrium chemistry network, our radiation hydrodynamics framework can be utilised to study a broad range of astrophysical problems, such as stellar and black hole (BH) feedback. Inaccuracies can arise from large timesteps and poor sampling, therefore we devised an adaptive time-stepping scheme and a fast approximation of the optically-thin radiation field with multiple sources. We test the method with several radiative transfer and radiation hydrodynamics tests that are given in Iliev et al. (2006, 2009). We further test our method with more dynamical situations, for example, the propagation of an ionisation front through a Rayleigh-Taylor instability, time-varying luminosities, and collimated radiation. The test suite also includes an...
Construction of Virtual Tuming Scene Based on Local Ray Tracing Algorithm
王国锋; 王子良; 王太勇
2003-01-01
According to the features of the turning simulation, a simplified Whitted lighting model is proposed based on the analysis of Phong and other local illumination model. Moreover, in order to obtain the natural lighting effects, local ray tracing algorithm is given to calculate the light intensity of every position during the course of the simulation. This method can calculate the refresh area before calculating the intersection line,simulate the machining environment accurately and reduce the calculating time. Finally, an example of the virtual cutting scene is shown to demonstrate the effects of the global illumination model. If the CUP is 1.3 G and the internal memory is 128 M, the refreshing time of virtual turning scene can be reduced by nine times. This study plays an important role in the enrichment of the virtual manufacturing theory and the promotion of the development of the advanced manufacturing technology.
Tracing the Lowest Propeller Line in Magellanic High-mass X-Ray Binaries
Christodoulou, Dimitris M.; Laycock, Silas G. T.; Yang, Jun; Fingerman, Samuel
2016-09-01
We have combined the published observations of high-mass X-ray binary (HMXB) pulsars in the Magellanic Clouds with a new processing of the complete archival data sets from the XMM-Newton and Chandra observatories in an attempt to trace the lowest propeller line below which accretion to polar caps is inhibited by the centrifugal force and the pulsations from the most weakly magnetized pulsars cease. Previously published data reveal that some of the faster-spinning pulsars with spin periods of P S < 12 s, detected at relatively low X-ray luminosities L X , appear to define such a line in the P S -L X diagram, characterized by a magnetic moment of μ = 3 × 1029 G cm3. This value implies the presence of surface magnetic fields of B ≥ 3 × 1011 G in the compact objects of this class. Only a few quiescent HMXBs are found below the propeller line: LXP4.40 and SXP4.78, for which XMM-Newton and Chandra null detections respectively placed firm upper limits on their X-ray fluxes in deep quiescence; and A0538-66, for which many sub-Eddington detections have never measured any pulsations. On the other hand, the data from the XMM-Newton and Chandra archives show clearly that, during routine observation cycles, several sources have been detected below the propeller line in extremely faint, nonpulsating states that can be understood as the result of weak magnetospheric emission when accretion to the poles is centrifugally stalled or severely diminished. We also pay attention to the anomalous X-ray pulsar CXOU J010043.1-721134 that was reported in HMXB surveys. Its pulsations and locations near and above the propeller line indicate that this pulsar could be accreting from a fossil disk.
Okumura, Akira; Noda, Koji; Rulten, Cameron
2016-03-01
We have developed a non-sequential ray-tracing simulation library, ROOT-basedsimulatorforraytracing (ROBAST), which is aimed to be widely used in optical simulations of cosmic-ray (CR) and gamma-ray telescopes. The library is written in C++, and fully utilizes the geometry library of the ROOT framework. Despite the importance of optics simulations in CR experiments, no open-source software for ray-tracing simulations that can be widely used in the community has existed. To reduce the dispensable effort needed to develop multiple ray-tracing simulators by different research groups, we have successfully used ROBAST for many years to perform optics simulations for the Cherenkov Telescope Array (CTA). Among the six proposed telescope designs for CTA, ROBAST is currently used for three telescopes: a Schwarzschild-Couder (SC) medium-sized telescope, one of SC small-sized telescopes, and a large-sized telescope (LST). ROBAST is also used for the simulation and development of hexagonal light concentrators proposed for the LST focal plane. Making full use of the ROOT geometry library with additional ROBAST classes, we are able to build the complex optics geometries typically used in CR experiments and ground-based gamma-ray telescopes. We introduce ROBAST and its features developed for CR experiments, and show several successful applications for CTA.
ENZO+MORAY: radiation hydrodynamics adaptive mesh refinement simulations with adaptive ray tracing
Wise, John H.; Abel, Tom
2011-07-01
We describe a photon-conserving radiative transfer algorithm, using a spatially-adaptive ray-tracing scheme, and its parallel implementation into the adaptive mesh refinement cosmological hydrodynamics code ENZO. By coupling the solver with the energy equation and non-equilibrium chemistry network, our radiation hydrodynamics framework can be utilized to study a broad range of astrophysical problems, such as stellar and black hole feedback. Inaccuracies can arise from large time-steps and poor sampling; therefore, we devised an adaptive time-stepping scheme and a fast approximation of the optically-thin radiation field with multiple sources. We test the method with several radiative transfer and radiation hydrodynamics tests that are given in Iliev et al. We further test our method with more dynamical situations, for example, the propagation of an ionization front through a Rayleigh-Taylor instability, time-varying luminosities and collimated radiation. The test suite also includes an expanding H II region in a magnetized medium, utilizing the newly implemented magnetohydrodynamics module in ENZO. This method linearly scales with the number of point sources and number of grid cells. Our implementation is scalable to 512 processors on distributed memory machines and can include the radiation pressure and secondary ionizations from X-ray radiation. It is included in the newest public release of ENZO.
Three-dimensional ray tracing for refractive correction of human eye ametropies
Jimenez-Hernandez, J. A.; Diaz-Gonzalez, G.; Trujillo-Romero, F.; Iturbe-Castillo, M. D.; Juarez-Salazar, R.; Santiago-Alvarado, A.
2016-09-01
Ametropies of the human eye, are refractive defects hampering the correct imaging on the retina. The most common ways to correct them is by means of spectacles, contact lenses, and modern methods as laser surgery. However, in any case it is very important to identify the ametropia grade for designing the optimum correction action. In the case of laser surgery, it is necessary to define a new shape of the cornea in order to obtain the wanted refractive correction. Therefore, a computational tool to calculate the focal length of the optical system of the eye versus variations on its geometrical parameters is required. Additionally, a clear and understandable visualization of the evaluation process is desirable. In this work, a model of the human eye based on geometrical optics principles is presented. Simulations of light rays coming from a punctual source at six meter from the cornea are shown. We perform a ray-tracing in three dimensions in order to visualize the focusing regions and estimate the power of the optical system. The common parameters of ametropies can be easily modified and analyzed in the simulation by an intuitive graphic user interface.
Kashima RAy-Tracing Service (KARATS) for high accurate GNSS positioning
Ichikawa, R.; Hobiger, T.; Hasegawa, S.; Tsutsumi, M.; Koyama, Y.; Kondo, T.
2010-12-01
Radio signal delays associated with the neutral atmosphere are one of the major error sources of space geodesy such as GPS, GLONASS, GALILEO, VLBI, In-SAR measurements. We have developed a state-of-art tool to estimate the atmospheric path delays by ray-tracing through JMA meso-scale analysis (MANAL data) data. The tools, which we have named 'KAshima RAytracing Tools (KARAT)', are capable of calculating total slant delays and ray-bending angles considering real atmospheric phenomena. Numerical weather models such as MANAL data have undergone a significant improvement of accuracy and spatial resolution, which makes it feasible to utilize them for the correction of atmosphere excess path delays. In the previous studies for evaluating KARAT performance, the KARAT solutions are slightly better than the solutions using VMF1 and GMF with linear gradient model for horizontal and height positions. Based on these results we have started the web-based online service, 'KAshima RAytracing Service (KARATS)' for providing the atmospheric delay correction of RINEX files on Jan 27th, 2010. The KARATS receives user's RINEX data via a proper web site (http://vps.nict.go.jp/karats/index.html) and processes user's data files using KARAT for reducing atmospheric slant delays. The reduced RINEX files are archived in the specific directory for each user on the KARATS server. Once the processing is finished the information of data archive is sent privately via email to each user. If user want to process a large amount of data files, user can prepare own server which archives them. The KARATS can get these files from the user's server using GNU ¥emph{wget} and performs ray-traced corrections. We will present a brief status of the KARATS and summarize first experiences gained after this service went operational in December 2009. In addition, we will also demonstrate the newest KARAT performance based on the 5km MANAL data which has been operational from April 7th, 2009 and an outlook on
Accounting for partiality in serial crystallography using ray-tracing principles.
Kroon-Batenburg, Loes M J; Schreurs, Antoine M M; Ravelli, Raimond B G; Gros, Piet
2015-09-01
Serial crystallography generates `still' diffraction data sets that are composed of single diffraction images obtained from a large number of crystals arbitrarily oriented in the X-ray beam. Estimation of the reflection partialities, which accounts for the expected observed fractions of diffraction intensities, has so far been problematic. In this paper, a method is derived for modelling the partialities by making use of the ray-tracing diffraction-integration method EVAL. The method estimates partialities based on crystal mosaicity, beam divergence, wavelength dispersion, crystal size and the interference function, accounting for crystallite size. It is shown that modelling of each reflection by a distribution of interference-function weighted rays yields a `still' Lorentz factor. Still data are compared with a conventional rotation data set collected from a single lysozyme crystal. Overall, the presented still integration method improves the data quality markedly. The R factor of the still data compared with the rotation data decreases from 26% using a Monte Carlo approach to 12% after applying the Lorentz correction, to 5.3% when estimating partialities by EVAL and finally to 4.7% after post-refinement. The merging R(int) factor of the still data improves from 105 to 56% but remains high. This suggests that the accuracy of the model parameters could be further improved. However, with a multiplicity of around 40 and an R(int) of ∼50% the merged still data approximate the quality of the rotation data. The presented integration method suitably accounts for the partiality of the observed intensities in still diffraction data, which is a critical step to improve data quality in serial crystallography.
The Use of Pro/Engineer CAD Software and Fishbowl Tool Kit in Ray-tracing Analysis
Nounu, Hatem N.; Kim, Myung-Hee Y.; Ponomarev, Artem L.; Cucinotta, Francis A.
2009-01-01
This document is designed as a manual for a user who wants to operate the Pro/ENGINEER (ProE) Wildfire 3.0 with the NASA Space Radiation Program's (SRP) custom-designed Toolkit, called 'Fishbowl', for the ray tracing of complex spacecraft geometries given by a ProE CAD model. The analysis of spacecraft geometry through ray tracing is a vital part in the calculation of health risks from space radiation. Space radiation poses severe risks of cancer, degenerative diseases and acute radiation sickness during long-term exploration missions, and shielding optimization is an important component in the application of radiation risk models. Ray tracing is a technique in which 3-dimensional (3D) vehicle geometry can be represented as the input for the space radiation transport code and subsequent risk calculations. In ray tracing a certain number of rays (on the order of 1000) are used to calculate the equivalent thickness, say of aluminum, of the spacecraft geometry seen at a point of interest called the dose point. The rays originate at the dose point and terminate at a homogenously distributed set of points lying on a sphere that circumscribes the spacecraft and that has its center at the dose point. The distance a ray traverses in each material is converted to aluminum or other user-selected equivalent thickness. Then all equivalent thicknesses are summed up for each ray. Since each ray points to a direction, the aluminum equivalent of each ray represents the shielding that the geometry provides to the dose point from that particular direction. This manual will first list for the user the contact information for help in installing ProE and Fishbowl in addition to notes on the platform support and system requirements information. Second, the document will show the user how to use the software to ray trace a Pro/E-designed 3-D assembly and will serve later as a reference for troubleshooting. The user is assumed to have previous knowledge of ProE and CAD modeling.
The Super Gaussian Laser Intensity Profile in HYDRA's 3D Laser Ray Trace Package
Sepke, Scott M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)
2017-01-05
In this note, the laser focal plane intensity pro le for a beam modeled using the 3D ray trace package in HYDRA is determined. First, the analytical model is developed followed by a practical numerical model for evaluating the resulting computationally intensive normalization factor for all possible input parameters.
User and programmers guide to the neutron ray-tracing package McStas, version 1.2
Nielsen, K.; Lefmann, K.
2000-01-01
The software package McStas is a tool for writing Monte Carlo ray-tracing simulations of neutron scattering instruments with very high complexity and precision. The simulations can compute all aspects of the performance of instruments and can thus be usedto optimize the use of existing equipment...
The forms of trace metals in an Illinois basin coal by x-ray absorption fine structure spectroscopy
Chou, I.-Ming; Bruinius, J.A.; Lytle, J.M.; Ruch, R.R.; Huggins, Frank E.; Huffman, G.P.; Ho, K.K.
1997-01-01
Utilities burning Illinois coals currently do not consider trace elements in their flue gas emissions. After the US EPA completes an investigation on trace elements, however, this may change and flue gas emission standards may be established. The mode of occurrence of a trace element may determine its cleanability and Hue gas emission potential. X-ray Absorption Fine Structure (XAFS) is a spectroscopic technique that can differentiate the mode of occurrence of an element, even at the low concentrations that trace elements are found in coal. This is principally accomplished by comparing the XAFS spectra of a coal to a database of reference sample spectra. This study evaluated the technique as a potential tool to examine six trace elements in an Illinois #6 coal. For the elements As and Zn, the present database provides a definitive interpretation on their mode of occurrence. For the elements Ti, V, Cr, and Mn the database of XAFS spectra of trace elements in coal was still too limited to allow a definitive interpretation. The data obtained on these elements, however, was sufficient to rule out several of the mineralogical possibilities that have been suggested previously. The results indicate that XAFS is a promising technique for the study of trace elements in coal.
Total reflection X-ray fluorescence analysis of trace-elements in candies marketed in Mexico
Martinez, T., E-mail: tmc@servidor.unam.m [Facultad de Quimica, Departamento de Quimica Inorganica y Nuclear. Universidad Nacional Autonoma de Mexico, Mexico D.F. 04510 (Mexico); Lartigue, J. [Facultad de Quimica, Departamento de Quimica Inorganica y Nuclear. Universidad Nacional Autonoma de Mexico, Mexico, D.F. 04510 (Mexico); Zarazua, G.; Avila-Perez, P. [National Institute of Nuclear Research. Ocoyoacac, Edo. de Mexico, 05045 (Mexico); Navarrete, M. [Facultad de Quimica, Departamento de Quimica Inorganica y Nuclear. Universidad Nacional Autonoma de Mexico, Mexico, D.F. 04510 (Mexico); Tejeda, S. [National Institute of Nuclear Research. Ocoyoacac, Edo. de Mexico, 05045 (Mexico)
2010-06-15
Trace metals concentrations in food are significant for nutrition, due either to their nature or toxicity. Sweets, including chewing gum and candies, are not exactly a food, but they usually are unwearied consumed by children, the most vulnerable age-group to any kind of metal contamination in the food chain. The presence of relatively high concentrations of heavy metals such as Lead elicits concern since children are highly susceptible to heavy metals poisoning. Trace-metals concentrations were determined for six different flavors of a Mexican candy by means of Total X-ray Fluorescence Spectrometry. Triplicate samples of the various candy's flavours (strawberry, pineapple, lemon, blackberry, orange and chilli) were digested in 8 mL of a mix of supra-pure HNO{sub 3} and H{sub 2}O{sub 2} (6 mL: 2 mL) in a microwave oven MARS-X. Results show the presence of essential and toxic elements such as Ti, Cr, Mn, Fe, Ni, Cu, Zn, Br, Rb, Sr, and Pb. All metal concentrations were higher and significantly different ({alpha} = 0.05) in chilli candy, compared to other candy flavours. Lead concentration fluctuated in the range of 0.102 to 0.342 {mu}g g{sup -1}. A discussion about risk consumption and concentration allowed by Mexican and International Norms is made. As a part of the Quality Control Program, a NIST standard of 'Citrus Leaves' and a blank were treated in the same way.
Lo, Ch. K.; Lim, Y. S.; Tan, S. G.; Rahman, F. A. [Faculty of Engineering and Science, University Tunku Abdul Rahman, Jalan Genting Klang, 53300, Kuala Lumpur (Malaysia)
2010-12-15
A Luminescent Solar Concentrator (LSC) is a transparent plate containing luminescent material with photovoltaic (PV) cells attached to its edges. Sunlight entering the plate is absorbed by the luminescent material, which in turn emits light. The emitted light propagates through the plate and arrives at the PV cells through total internal reflection. The ratio of the area of the relatively cheap polymer plate to that of the expensive PV cells is increased, and the cost per unit of solar electricity can be reduced by 75%. To improve the emission performance of LSCs, simulation modeling of LSCs becomes essential. Ray-tracing modeling is a popular approach for simulating LSCs due to its great ability of modeling various LSC structures under direct and diffuse sunlight. However, this approach requires substantial amount of measurement input data. Also, the simulation time is enormous because it is a forward-ray tracing method that traces all the rays propagating from the light source to the concentrator. On the other hand, the thermodynamic approach requires substantially less input parameters and simulation time, but it can only be used to model simple LSC designs with direct sunlight. Therefore, a new hybrid model was developed to perform various simulation studies effectively without facing the issues arisen from the existing ray-tracing and thermodynamic models. The simulation results show that at least 60% of the total output irradiance of a LSC is contributed by the light trapped and channeled by the LSC. The novelty of this hybrid model is the concept of integrating the thermodynamic model with a well-developed Radiance ray-tracing model, hence making this model as a fast, powerful and cost-effective tool for the design of LSCs. (authors)
Chin Kim Lo
2010-11-01
Full Text Available A Luminescent Solar Concentrator (LSC is a transparent plate containing luminescent material with photovoltaic (PV cells attached to its edges. Sunlight entering the plate is absorbed by the luminescent material, which in turn emits light. The emitted light propagates through the plate and arrives at the PV cells through total internal reflection. The ratio of the area of the relatively cheap polymer plate to that of the expensive PV cells is increased, and the cost per unit of solar electricity can be reduced by 75%. To improve the emission performance of LSCs, simulation modeling of LSCs becomes essential. Ray-tracing modeling is a popular approach for simulating LSCs due to its great ability of modeling various LSC structures under direct and diffuse sunlight. However, this approach requires substantial amount of measurement input data. Also, the simulation time is enormous because it is a forward-ray tracing method that traces all the rays propagating from the light source to the concentrator. On the other hand, the thermodynamic approach requires substantially less input parameters and simulation time, but it can only be used to model simple LSC designs with direct sunlight. Therefore, a new hybrid model was developed to perform various simulation studies effectively without facing the issues arisen from the existing ray-tracing and thermodynamic models. The simulation results show that at least 60% of the total output irradiance of a LSC is contributed by the light trapped and channeled by the LSC. The novelty of this hybrid model is the concept of integrating the thermodynamic model with a well-developed Radiance ray-tracing model, hence making this model as a fast, powerful and cost-effective tool for the design of LSCs.
Gualdi, Giulia; Illuminati, Fabrizio
2010-01-01
We introduce and discuss the concept of modular entanglement. This is the entanglement that is established between the end points of modular systems composed by sets of interacting blocks of arbitrarily fixed size. We show that end-to-end modular entanglement scales in the thermodynamic limit and rapidly saturates with the number of constituent blocks. We clarify the mechanisms underlying the onset of entanglement between distant and non-interacting quantum systems and its optimization for applications to quantum repeaters and entanglement distribution and sharing.
Gualdi, Giulia; Giampaolo, Salvatore M; Illuminati, Fabrizio
2011-02-04
We introduce and discuss the concept of modular entanglement. This is the entanglement that is established between the end points of modular systems composed by sets of interacting moduli of arbitrarily fixed size. We show that end-to-end modular entanglement scales in the thermodynamic limit and rapidly saturates with the number of constituent moduli. We clarify the mechanisms underlying the onset of entanglement between distant and noninteracting quantum systems and its optimization for applications to quantum repeaters and entanglement distribution and sharing.
Identification of Gravity wave Sources over Tropical Latitudes Using Reverse Ray Tracing technique
Venkat Ratnam, Madineni; Pramitha, M.
2016-07-01
Sources and propagation characteristics of high-frequency gravity waves (GWs) observed in the mesosphere using airglow emissions from Gadanki (13.5oN, 79.2oE) and Hyderabad (17.5oN, 78.5oE) are investigated using reverse ray tracing. Wave amplitudes are also traced back, including both radiative and diffusive damping. For this a climatological model of the background atmosphere for the Gadanki region has been developed using nearly 30 years of observations available from a variety of ground based (MST radar, radiosondes, MF radar) and rocket- and satellite-borne measurements. With the reverse ray-tracing method, the source locations for wave events could be identified to be in the upper troposphere. Uncertainty in locating the terminal points of wave events in the horizontal direction is estimated to be within 50-100 km and 150-300 km for Gadanki and Hyderabad wave events, respectively. This uncertainty arises mainly due to non-consideration of the day-to-day variability in the tidal amplitudes. Interestingly, large (~9ms-1 km-1) vertical shears in the horizontal wind are noticed near the ray terminal points (at 10-12 km altitude) and are thus identified to be the source for generating the observed high phase- speed, high-frequency GWs. We also tried to identify the sources for the GWs which are observed during Indo-French campaign conducted during May 2014. Uniqueness of the present study lies in using near-real time background atmosphere data from simultaneous radiosonde and meteor radar covering both source and propagation/dissipation regions of GWs. When we searched for the sources near the terminal points, deep convection is found to be a source for these events. We also tried to identify the sources of inertia-gravity waves (IGWs) that are observed in the troposphere and lower stratosphere during different seasons using long-term (2006-2014) high resolution radiosonde observations. In general, 50% of the waves observed over this location have convection as
Magnetospherically reflected chorus waves revealed by ray tracing with CLUSTER data
M. Parrot
Full Text Available This paper is related to the propagation characteristics of a chorus emission recorded simultaneously by the 4 satellites of the CLUSTER mission on 29 October 2001 between 01:00 and 05:00 UT. During this day, the spacecraft (SC 1, 2, and 4 are relatively close to each other but SC3 has been delayed by half an hour. We use the data recorded aboard CLUSTER by the STAFF spectrum analyser. This instrument provides the cross spectral matrix of three magnetic and two electric field components. Dedicated software processes this spectral matrix in order to determine the wave normal directions relative to the Earth’s magnetic field. This calculation is done for the 4 satellites at different times and different frequencies and allows us to check the directions of these waves. Measurements around the magnetic equator show that the parallel component of the Poynting vector changes its sign when the satellites cross the equator region. It indicates that the chorus waves propagate away from this region which is considered as the source area of these emissions. This is valid for the most intense waves observed on the magnetic and electric power spectrograms. But it is also observed on SC1, SC2, and SC4 that lower intensity waves propagate toward the equator simultaneously with the SC3 intense chorus waves propagating away from the equator. Both waves are at the same frequency. Using the wave normal directions of these waves, a ray tracing study shows that the waves observed by SC1, SC2, and SC4 cross the equatorial plane at the same location as the waves observed by SC3. SC3 which is 30 minutes late observes the waves that originate first from the equator; meanwhile, SC1, SC2, and SC4 observe the same waves that have suffered a Lower Hybrid Resonance (LHR reflection at low altitudes (based on the ray tracing analysis and now return to the equator at a different location with a lower intensity. Similar phenomenon is observed when all SC are on the other side
Mauro, N A; Kelton, K F
2011-03-01
High-energy x-ray diffraction studies of metallic liquids provide valuable information about structural evolution on the atomic length scale, leading to insights into the origin of the nucleation barrier and the processes of supercooling and glass formation. The containerless processing of the beamline electrostatic levitation (BESL) facility allows coordinated thermophysical and structural studies of equilibrium and supercooled liquids to be made in a contamination-free, high-vacuum (∼10(-8) Torr) environment. To date, the incorporation of electrostatic levitation facilities into synchrotron beamlines has been difficult due to the large footprint of the apparatus and the difficulties associated with its transportation and implementation. Here, we describe a modular levitation facility that is optimized for diffraction studies of high-temperature liquids at high-energy synchrotron beamlines. The modular approach used in the apparatus design allows it to be easily transported and quickly setup. Unlike most previous electrostatic levitation facilities, BESL can be operated by a single user instead of a user team.
Eccentric small-zone ray tracing wavefront aberrometry for refraction in keratoconus.
Fredriksson, Anneli; Behndig, Anders
2016-11-01
To compare objective refraction using small-zone eccentric laser ray tracing (LRT) wavefront aberrometry to standard autorefraction in keratoconus (KC), and whether the visual acuities achieved with these refractions differ from corresponding values in healthy eyes. Twenty-nine eyes of 29 patients with KC and 29 eyes of 29 healthy controls were included in this prospective unmasked case-control study. The uncorrected (UCVA) and spectacle-corrected (SCVA) Early Treatment Diabetic Retinopathy Study (ETDRS) visual acuities based on refractions derived from LRT in central and four eccentric zones were compared to those achieved with standard autorefraction. The spherical equivalent (M) and two astigmatic power vectors (C0 and C45) were calculated for all refractions. Pentacam HR(®) was used to generate keratometry readings of the corresponding zones. In KC, the refraction from the upper nasal zone rendered a higher SCVA than the standard autorefraction more often than in the controls (p refractions rendered similar SCVA:s in KC. Pentacam HR(®) showed higher keratometry readings infero-temporally, but also lower readings supero-nasally, compared to controls. In KC, eccentric LRT measurements gave better SCVA than standard autorefraction more often than in healthy eyes. Eccentric LRT may become a valuable tool in the demanding task of subjective refraction in KC. © 2016 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.
Stevens, John Colby [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). The Joint Center for Artificial Photosynthesis; Univ. of California, Berkeley, CA (United States). Dept. of Mechanical Engineering
2012-12-01
Ray tracing was used to perform optical optimization of arrays of photovoltaic microrods and explore the interaction between light and bubbles of oxygen gas on the surface of the microrods. The incident angle of light was varied over a wide range. The percent of incident light absorbed by the microrods and reflected by the bubbles was computed over this range. It was found that, for the 10 μm diameter, 100 μm tall SrTiO_{3} microrods simulated in the model, the optimal center-to-center spacing was 14 μm for a square grid. This geometry produced 75% average and 90% maximum absorbance. For a triangular grid using the same microrods, the optimal center-to-center spacing was 14 μm. This geometry produced 67% average and 85% maximum absorbance. For a randomly laid out grid of 5 μm diameter, 100 μm tall SrTiO_{3} microrods with an average center-to-center spacing of 20 μm, the average absorption was 23% and the maximum absorption was 43%. For a 50% areal coverage fraction of bubbles on the absorber surface, between 2%-20% of the incident light energy was reflected away from the rods by the bubbles, depending upon incident angle and bubble morphology.
Yang, Que; Wang, Shanshan; Wang, Kai; Zhang, Chunyu; Zhang, Lu; Meng, Qingyu; Zhu, Qiudong
2015-08-01
For normal eyes without history of any ocular surgery, traditional equations for calculating intraocular lens (IOL) power, such as SRK-T, Holladay, Higis, SRK-II, et al., all were relativley accurate. However, for eyes underwent refractive surgeries, such as LASIK, or eyes diagnosed as keratoconus, these equations may cause significant postoperative refractive error, which may cause poor satisfaction after cataract surgery. Although some methods have been carried out to solve this problem, such as Hagis-L equation[1], or using preoperative data (data before LASIK) to estimate K value[2], no precise equations were available for these eyes. Here, we introduced a novel intraocular lens power estimation method by accurate ray tracing with optical design software ZEMAX. Instead of using traditional regression formula, we adopted the exact measured corneal elevation distribution, central corneal thickness, anterior chamber depth, axial length, and estimated effective lens plane as the input parameters. The calculation of intraocular lens power for a patient with keratoconus and another LASIK postoperative patient met very well with their visual capacity after cataract surgery.
Sakurai, K; Inoue, K; Yagi, N
2001-01-01
The downsizing of a Johansson-type X-ray fluorescence (XRF) spectrometer has been examined as a way of enhancing detection efficiency with a tolerable loss of energy resolution. A compact spectrometer equipped with a Ge(2 2 0) analyzing crystal with a Rowland radius of 120 mm has been tested with a highly brilliant helical undulator source at BL40XU, SPring-8. The energy resolution obtained for cobalt K alpha sub 1 (6930.32 eV) was 8.8 eV, which is 10-20 times better than that obtained using a Si(Li) detector, and effectively improved the signal-to-background ratio for XRF spectra. The combination of the present spectrometer and a third generation synchrotron source could provide new opportunities for trace analytical applications, which have been difficult so far by conventional synchrotron XRF experiments based on a Si(Li) detector system. The detection limit obtained for solid bulk samples has reached a level of several tens of ppb.
Liang, Yicheng; Peng, Hao
2015-02-07
Depth-of-interaction (DOI) poses a major challenge for a PET system to achieve uniform spatial resolution across the field-of-view, particularly for small animal and organ-dedicated PET systems. In this work, we implemented an analytical method to model system matrix for resolution recovery, which was then incorporated in PET image reconstruction on a graphical processing unit platform, due to its parallel processing capacity. The method utilizes the concepts of virtual DOI layers and multi-ray tracing to calculate the coincidence detection response function for a given line-of-response. The accuracy of the proposed method was validated for a small-bore PET insert to be used for simultaneous PET/MR breast imaging. In addition, the performance comparisons were studied among the following three cases: 1) no physical DOI and no resolution modeling; 2) two physical DOI layers and no resolution modeling; and 3) no physical DOI design but with a different number of virtual DOI layers. The image quality was quantitatively evaluated in terms of spatial resolution (full-width-half-maximum and position offset), contrast recovery coefficient and noise. The results indicate that the proposed method has the potential to be used as an alternative to other physical DOI designs and achieve comparable imaging performances, while reducing detector/system design cost and complexity.
Woei Leow, Shin; Corrado, Carley; Osborn, Melissa; Isaacson, Michael; Alers, Glenn; Carter, Sue A.
2013-06-01
Luminescent solar concentrators (LSC) collect ambient light from a broad range of angles and concentrate the captured light onto photovoltaic (PV) cells. LSCs with front-facing cells collect direct and indirect sunlight ensuring a gain factor greater than one. The flexible placement and percentage coverage of PV cells on the LSC panel allow for layout adjustments to be made in order to balance re-absorption losses and the level of light concentration desired. A weighted Monte Carlo ray tracing program was developed to study the transport of photons and loss mechanisms in the LSC to aid in design optimization. The program imports measured absorption/emission spectra of an organic luminescent dye (LR305), the transmission coefficient, and refractive index of acrylic as parameters that describe the system. Simulations suggest that for LR305, 8-10 cm of luminescent material surrounding the PV cell yields the highest increase in power gain per unit area of LSC added, thereby determining the ideal spacing between PV cells in the panel. For rectangular PV cells, results indicate that for each centimeter of PV cell width, an additional increase of 0.15 mm to the waveguide thickness is required to efficiently transport photon collected by the LSC to the PV cell with minimal loss.
A model of polarized-beam AGS in the ray-tracing code Zgoubi
Meot, F. [Brookhaven National Lab. (BNL), Upton, NY (United States); Ahrens, L. [Brookhaven National Lab. (BNL), Upton, NY (United States); Brown, K. [Brookhaven National Lab. (BNL), Upton, NY (United States); Dutheil, Y. [Brookhaven National Lab. (BNL), Upton, NY (United States); Glenn, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Huang, H. [Brookhaven National Lab. (BNL), Upton, NY (United States); Roser, T. [Brookhaven National Lab. (BNL), Upton, NY (United States); Shoefer, V. [Brookhaven National Lab. (BNL), Upton, NY (United States); Tsoupas, N. [Brookhaven National Lab. (BNL), Upton, NY (United States)
2016-07-12
A model of the Alternating Gradient Synchrotron, based on the AGS snapramps, has been developed in the stepwise ray-tracing code Zgoubi. It has been used over the past 5 years in a number of accelerator studies aimed at enhancing RHIC proton beam polarization. It is also used to study and optimize proton and Helion beam polarization in view of future RHIC and eRHIC programs. The AGS model in Zgoubi is operational on-line via three different applications, ’ZgoubiFromSnaprampCmd’, ’AgsZgoubiModel’ and ’AgsModelViewer’, with the latter two essentially interfaces to the former which is the actual model ’engine’. All three commands are available from the controls system application launcher in the AGS ’StartUp’ menu, or from eponymous commands on shell terminals. Main aspects of the model and of its operation are presented in this technical note, brief excerpts from various studies performed so far are given for illustration, means and methods entering in ZgoubiFromSnaprampCmd are developed further in appendix.
Leow, Shin Woei; Corrado, Carley; Osborn, Melissa; Carter, Sue A.
2013-09-01
Luminescent solar concentrators (LSCs) have the ability to receive light from a wide range of angles, concentrating the captured light onto small photo active areas. This enables greater incorporation of LSCs into building designs as windows, skylights and wall claddings in addition to rooftop installations of current solar panels. Using relatively cheap luminescent dyes and acrylic waveguides to effect light concentration onto lesser photovoltaic (PV) cells, there is potential for this technology to approach grid price parity. We employ a panel design in which the front facing PV cells collect both direct and concentrated light ensuring a gain factor greater than one. This also allows for flexibility in determining the placement and percentage coverage of PV cells during the design process to balance reabsorption losses against the power output and level of light concentration desired. To aid in design optimization, a Monte-Carlo ray tracing program was developed to study the transport of photons and loss mechanisms in LSC panels. The program imports measured absorption/emission spectra and transmission coefficients as simulation parameters with interactions of photons in the panel determined by comparing calculated probabilities with random number generators. LSC panels with multiple dyes or layers can also be simulated. Analysis of the results reveals optimal panel dimensions and PV cell layouts for maximum power output for a given dye concentration, absorbtion/emission spectrum and quantum efficiency.
Using Stochastic Ray Tracing to Simulate a Dense Time Series of Gross Primary Productivity
Martin van Leeuwen
2015-12-01
Full Text Available Eddy-covariance carbon dioxide flux measurement is an established method to estimate primary productivity at the forest stand level (typically 10 ha. To validate eddy-covariance estimates, researchers rely on extensive time-series analysis and an assessment of flux contributions made by various ecosystem components at spatial scales much finer than the eddy-covariance footprint. Scaling these contributions to the stand level requires a consideration of the heterogeneity in the canopy radiation field. This paper presents a stochastic ray tracing approach to predict the probabilities of light absorption from over a thousand hemispherical directions by thousands of individual scene elements. Once a look-up table of absorption probabilities is computed, dynamic illumination conditions can be simulated in a computationally realistic time, from which stand-level gross primary productivity can be obtained by integrating photosynthetic assimilation over the scene. We demonstrate the method by inverting a leaf-level photosynthesis model with eddy-covariance and meteorological data. Optimized leaf photosynthesis parameters and canopy structure were able to explain 75% of variation in eddy-covariance gross primary productivity estimates, and commonly used parameters, including photosynthetic capacity and quantum yield, fell within reported ranges. Remaining challenges are discussed including the need to address the distribution of radiation within shoots and needles.
Zhu, Yang; Zhang, Xin; Liu, Tao; Wu, Yanxiong; Shi, Guangwei; Wang, Lingjie
2015-07-01
A long wave infrared imaging system operated for space exploration of faint target is highly sensitive to stray radiation. We present an integrative suppression process of internal and external stray radiation. A compact and re-imaging LWIR catadioptric telescope is designed as practical example and internal and external stray radiation is analyzed for this telescope. The detector is cryogenically cooled with 100% cold shield efficiency of Lyot stop. A non-sequential ray tracing technique is applied to investigate how the stray radiation propagates inside optical system. The simulation and optimization during initial design stage are proceeded to avoid subversive defect that the stray radiation disturbs the target single. The quantitative analysis of stray radiation irradiance emitted by lenses and structures inside is presented in detail. The optical elements, which operate at room-temperature due to the limitation of weight and size, turn to be the significant stray radiation sources. We propose a method combined infrared material selection and optical form optimization to reduce the internal stray radiation of lens. We design and optimize mechanical structures to achieve a further attenuation of internal stray radiation power. The point source transmittance (PST) is calculated to assess the external radiation which comes from the source out of view field. The ghost of bright target due to residual reflection of optical coatings is simulated. The results show that the performance of stray radiation suppression is dramatically improved by iterative optimization and modification of optomechanical configurations.
Trace metal content in aspirin and women's cosmetics via proton induced x-ray emission (PIXE)
Hichwa, B.P.; Pun, D.D.; Wang, D.
1981-04-01
A multielemental analysis to determine the trace metal content of generic and name-brand aspirins and name-brand lipsticks was done via proton induced x-ray (PIXE) measurements. The Hope College PIXE system is described as well as the target preparation methods. The trace metal content of twelve brands of aspirin and aspirin substitutes and fourteen brands of lipstick are reported. Detection limits for most elements are in the range of 100 parts per billion (ppb) to 10 parts per million (ppm).
无
2000-01-01
A method using synchrotron radiation X-ray fluorescence analysis to in situ determine trace elements during protein electrophoretically separating process was established. The distribution of elements in protein bands for human liver cytosolic sample separated by SDS-PAGE was analyzed along polyacrylamide gel. The results showed that the protein fraction of peak III in cytosol was mainly composed of metal ion Zn-associated proteins, being in agreement with that given by atomic absorption spectrometry. Thus, it demonstrated the feasibility of this novel technique for in situ analysis of trace elements in protein bands.
陈春英; 章佩群; 柴之芳; 李光城; 黄宇营
2000-01-01
A method using synchrotron radiation X-ray fluorescence analysis to in situ determine trace elements during protein electrophoretically separating process was established. The distribution of elements in protein bands for human liver cytosolic sample separated by SDS-PAGE was analyzed a-long polyacrylamide gel. The results showed that the protein fraction of peak III in cvtosol was mainly composed of metal ion Zn-associated proteins, being in agreement with that given by atomic absorption spectrometry. Thus, it demonstrated the feasibility of this novel technique for in situ analysis of trace elements in protein bands.
Kobayashi, Tatsuo; Urakawa, Yuko
2016-01-01
Modular invariance is a striking symmetry in string theory, which may keep stringy corrections under control. In this paper, we investigate a phenomenological consequence of the modular invariance, assuming that this symmetry is preserved as well as in a four dimensional (4D) low energy effective field theory. As a concrete setup, we consider a modulus field $T$ whose contribution in the 4D effective field theory remains invariant under the modular transformation and study inflation drived by $T$. The modular invariance restricts a possible form of the scalar potenntial. As a result, large field models of inflation are hardly realized. Meanwhile, a small field model of inflation can be still accomodated in this restricted setup. The scalar potential traced during the slow-roll inflation mimics the hilltop potential $V_{ht}$, but it also has a non-negligible deviation from $V_{ht}$. Detecting the primordial gravitational waves predicted in this model is rather challenging. Yet, we argue that it may be still po...
Kobayashi, Tatsuo [Department of Physics, Hokkaido University,Kita, Sapporo, 060-0810 (Japan); Nitta, Daisuke; Urakawa, Yuko [Department of Physics and Astrophysics, Nagoya University,Chikusa, Nagoya 464-8602 (Japan)
2016-08-08
Modular invariance is a striking symmetry in string theory, which may keep stringy corrections under control. In this paper, we investigate a phenomenological consequence of the modular invariance, assuming that this symmetry is preserved as well as in a four dimensional (4D) low energy effective field theory. As a concrete setup, we consider a modulus field T whose contribution in the 4D effective field theory remains invariant under the modular transformation and study inflation drived by T. The modular invariance restricts a possible form of the scalar potenntial. As a result, large field models of inflation are hardly realized. Meanwhile, a small field model of inflation can be still accomodated in this restricted setup. The scalar potential traced during the slow-roll inflation mimics the hilltop potential V{sub ht}, but it also has a non-negligible deviation from V{sub ht}. Detecting the primordial gravitational waves predicted in this model is rather challenging. Yet, we argue that it may be still possible to falsify this model by combining the information in the reheating process which can be determined self-completely in this setup.
Kobayashi, Tatsuo; Nitta, Daisuke; Urakawa, Yuko
2016-08-01
Modular invariance is a striking symmetry in string theory, which may keep stringy corrections under control. In this paper, we investigate a phenomenological consequence of the modular invariance, assuming that this symmetry is preserved as well as in a four dimensional (4D) low energy effective field theory. As a concrete setup, we consider a modulus field T whose contribution in the 4D effective field theory remains invariant under the modular transformation and study inflation drived by T. The modular invariance restricts a possible form of the scalar potenntial. As a result, large field models of inflation are hardly realized. Meanwhile, a small field model of inflation can be still accomodated in this restricted setup. The scalar potential traced during the slow-roll inflation mimics the hilltop potential Vht, but it also has a non-negligible deviation from Vht. Detecting the primordial gravitational waves predicted in this model is rather challenging. Yet, we argue that it may be still possible to falsify this model by combining the information in the reheating process which can be determined self-completely in this setup.
Component-level test of molded freeform optics for LED beam shaping using experimental ray tracing
Gutierrez, Gustavo; Hilbig, David; Fleischmann, Friedrich; Henning, Thomas
2017-06-01
Due to the high demand of LED light sources, the need to modify their radiation pattern to meet specific application requirements has also increased. This is mostly achieved by using molded secondary optics, which are composed of a combination of several aspherical and freeform surfaces. Unfortunately, the manufacturers of these secondary optics only provide output information at system level, making impossible to independently characterize the secondary optic in order to determine the sources of erroneous results. For this reason, it is necessary to perform a component-level verification leading to the validation of the correctness of the produced secondary optic independently of the light source. To understand why traditional inspection methods fail, it is necessary to take into account that not only errors due to irregularities on the lens surface like pores, glass indentations or scratches affect the performance of the lens, but also differences in refractive index appear after the compression during fabrication process. These internal alterations are generally produced during the cooling stage and their effect over the performance of the lens are not possible to be measured using tactile techniques. Additionally, the small size of the lens and the freeform characteristics of its surface introduce additional difficulties to perform its validation. In this work, the component-level test is done by obtaining the ray mapping function (RMF) which describes the deflection of the light beam as a function of the input angle. To obtain the RMF, firstly a collimated light source is held fix and the lens is rotated. Thus, a virtual point source is created and subsequently by using experimental ray tracing it is possible to determine the ray slopes, which are used to the retrieve the RMF. Under the assumption that the optical system under analysis is lossless and considering the principle of energy conservation, it is possible under specific conditions to use this new
E. Achmad
2006-12-01
Full Text Available Gravity wave signatures were extracted from OH airglow observations using all-sky CCD imagers at four different stations: Cachoeira Paulista (CP (22.7° S, 45° W and São João do Cariri (7.4° S, 36.5° W, Brazil; Tanjungsari (TJS (6.9° S, 107.9° E, Indonesia and Shigaraki (34.9° N, 136° E, Japan. The gravity wave parameters are used as an input in a reverse ray tracing model to study the gravity wave vertical propagation trajectory and to estimate the wave source region. Gravity waves observed near the equator showed a shorter period and a larger phase velocity than those waves observed at low-middle latitudes. The waves ray traced down into the troposphere showed the largest horizontal wavelength and phase speed. The ray tracing results also showed that at CP, Cariri and Shigaraki the majority of the ray paths stopped in the mesosphere due to the condition of m2m2m|→∞, which suggests the presence of ducting waves and/or waves generated in-situ. In the troposphere, the possible gravity wave sources are related to meteorological front activities and cloud convections at CP, while at Cariri and TJS tropical cloud convections near the equator are the most probable gravity wave sources. The tropospheric jet stream and the orography are thought to be the major responsible sources for the waves observed at Shigaraki.
Desnijder, Karel; Hanselaer, Peter; Meuret, Youri
2016-04-01
A key requirement to obtain a uniform luminance for a side-lit LED backlight is the optimised spatial pattern of structures on the light guide that extract the light. The generation of such a scatter pattern is usually performed by applying an iterative approach. In each iteration, the luminance distribution of the backlight with a particular scatter pattern is analysed. This is typically performed with a brute-force ray-tracing algorithm, although this approach results in a time-consuming optimisation process. In this study, the Adding-Doubling method is explored as an alternative way for evaluating the luminance of a backlight. Due to the similarities between light propagating in a backlight with extraction structures and light scattering in a cloud of light scatterers, the Adding-Doubling method which is used to model the latter could also be used to model the light distribution in a backlight. The backlight problem is translated to a form upon which the Adding-Doubling method is directly applicable. The calculated luminance for a simple uniform extraction pattern with the Adding-Doubling method matches the luminance generated by a commercial raytracer very well. Although successful, no clear computational advantage over ray tracers is realised. However, the dynamics of light propagation in a light guide as used the Adding-Doubling method, also allow to enhance the efficiency of brute-force ray-tracing algorithms. The performance of this enhanced ray-tracing approach for the simulation of backlights is also evaluated against a typical brute-force ray-tracing approach.
Bailey, M J; Morgan, R M; Comini, P; Calusi, S; Bull, P A
2012-03-06
The independent verification in a forensics context of quartz grain morphological typing by scanning electron microscopy was demonstrated using particle-induced X-ray emission (PIXE) and particle-induced γ-ray emission (PIGE). Surface texture analysis by electron microscopy and high-sensitivity trace element mapping by PIXE and PIGE are independent analytical techniques for identifying the provenance of quartz in sediment samples in forensic investigations. Trace element profiling of the quartz grain matrix separately from the quartz grain inclusions served to differentiate grains of different provenance and indeed went some way toward discriminating between different quartz grain types identified in a single sample of one known forensic provenance. These results confirm the feasibility of independently verifying the provenance of critical samples from forensic cases.
Cheng, Ruida; Jackson, Jennifer N.; McCreedy, Evan S.; Gandler, William; Eijkenboom, J. J. F. A.; van Middelkoop, M.; McAuliffe, Matthew J.; Sheehan, Frances T.
2016-03-01
The paper presents an automatic segmentation methodology for the patellar bone, based on 3D gradient recalled echo and gradient recalled echo with fat suppression magnetic resonance images. Constricted search space outlines are incorporated into recursive ray-tracing to segment the outer cortical bone. A statistical analysis based on the dependence of information in adjacent slices is used to limit the search in each image to between an outer and inner search region. A section based recursive ray-tracing mechanism is used to skip inner noise regions and detect the edge boundary. The proposed method achieves higher segmentation accuracy (0.23mm) than the current state-of-the-art methods with the average dice similarity coefficient of 96.0% (SD 1.3%) agreement between the auto-segmentation and ground truth surfaces.
Weeratunga, S K
2008-11-06
Ares and Kull are mature code frameworks that support ALE hydrodynamics for a variety of HEDP applications at LLNL, using two widely different meshing approaches. While Ares is based on a 2-D/3-D block-structured mesh data base, Kull is designed to support unstructured, arbitrary polygonal/polyhedral meshes. In addition, both frameworks are capable of running applications on large, distributed-memory parallel machines. Currently, both these frameworks separately support assorted collections of physics packages related to HEDP, including one for the energy deposition by laser/ion-beam ray tracing. This study analyzes the options available for developing a common laser/ion-beam ray tracing package that can be easily shared between these two code frameworks and concludes with a set of recommendations for its development.
BEaTriX, expanded X-ray beam facility for testing modular elements of telescope optics: an update
Pelliciari, Carlo; Bonnini, Elisa; Buffagni, Elisa; Ferrari, Claudio; Pareschi, Giovanni; Tagliaferri, Gianpiero
2016-01-01
We present in this paper an update on the design of BEaTriX (Beam Expander Testing X-ray facility), an X-ray apparatus to be realized at INAF/OAB and that will generate an expanded, uniform and parallel beam of soft X-rays. BEaTriX will be used to perform the functional tests of X-ray focusing modules of large X-ray optics such as those for the ATHENA X-ray observatory, using the Silicon Pore Optics (SPO) as a baseline technology, and Slumped Glass Optics (SGO) as a possible alternative. Performing the tests in X-rays provides the advantage of an in-situ, at-wavelength quality control of the optical modules produced in series by the industry, performing a selection of the modules with the best angular resolution, and, in the case of SPOs, there is also the interesting possibility to align the parabolic and the hyperbolic stacks directly under X-rays, to minimize the aberrations. However, a parallel beam with divergence below 2 arcsec is necessary in order to measure mirror elements that are expected to reach ...
Fokker-Planck/Ray Tracing for Electron Bernstein and Fast Wave Modeling in Support of NSTX
Harvey, R. W. [CompX, Del Mar, CA (United States)
2009-11-12
This DOE grant supported fusion energy research, a potential long-term solution to the world's energy needs. Magnetic fusion, exemplified by confinement of very hot ionized gases, i.e., plasmas, in donut-shaped tokamak vessels is a leading approach for this energy source. Thus far, a mixture of hydrogen isotopes has produced 10's of megawatts of fusion power for seconds in a tokamak reactor at Princeton Plasma Physics Laboratory in New Jersey. The research grant under consideration, ER54684, uses computer models to aid in understanding and projecting efficacy of heating and current drive sources in the National Spherical Torus Experiment, a tokamak variant, at PPPL. The NSTX experiment explores the physics of very tight aspect ratio, almost spherical tokamaks, aiming at producing steady-state fusion plasmas. The current drive is an integral part of the steady-state concept, maintaining the magnetic geometry in the steady-state tokamak. CompX further developed and applied models for radiofrequency (rf) heating and current drive for applications to NSTX. These models build on a 30 year development of rf ray tracing (the all-frequencies GENRAY code) and higher dimensional Fokker-Planck rf-collisional modeling (the 3D collisional-quasilinear CQL3D code) at CompX. Two mainline current-drive rf modes are proposed for injection into NSTX: (1) electron Bernstein wave (EBW), and (2) high harmonic fast wave (HHFW) modes. Both these current drive systems provide a means for the rf to access the especially high density plasma--termed high beta plasma--compared to the strength of the required magnetic fields. The CompX studies entailed detailed modeling of the EBW to calculate the efficiency of the current drive system, and to determine its range of flexibility for driving current at spatial locations in the plasma cross-section. The ray tracing showed penetration into NSTX bulk plasma, relatively efficient current drive, but a limited ability to produce current over
He, Wenjun; Fu, Yuegang; Zheng, Yang; Zhang, Lei; Wang, Jiake; Liu, Zhiying; Zheng, Jianping
2013-07-01
The output polarization states of corner cubes (for both uncoated and metal-coated surfaces) with an input beam of arbitrary polarization state and of arbitrary tilt angle to the cube have been analyzed by using the three-dimensional polarization ray-tracing matrix method. The diattenuation and retardance of the corner-cube retroreflector (CCR) for all six different ray paths are calculated, and the relationships to the tilt angle and the tilt orientation angle are shown. When the tilt angle is large, hollow metal-coated CCR is more appropriate than solid metal-coated CCR for the case that the polarization states of output beam should be controlled.
Jefferies, K.
1994-01-01
OFFSET is a ray tracing computer code for optical analysis of a solar collector. The code models the flux distributions within the receiver cavity produced by reflections from the solar collector. It was developed to model the offset solar collector of the solar dynamic electric power system being developed for Space Station Freedom. OFFSET has been used to improve the understanding of the collector-receiver interface and to guide the efforts of NASA contractors also researching the optical components of the power system. The collector for Space Station Freedom consists of 19 hexagonal panels each containing 24 triangular, reflective facets. Current research is geared toward optimizing flux distribution inside the receiver via changes in collector design and receiver orientation. OFFSET offers many options for experimenting with the design of the system. The offset parabolic collector model configuration is determined by an input file of facet corner coordinates. The user may choose other configurations by changing this file, but to simulate collectors that have other than 19 groups of 24 triangular facets would require modification of the FORTRAN code. Each of the roughly 500 facets in the assembled collector may be independently aimed to smooth out, or tailor, the flux distribution on the receiver's wall. OFFSET simulates the effects of design changes such as in receiver aperture location, tilt angle, and collector facet contour. Unique features of OFFSET include: 1) equations developed to pseudo-randomly select ray originating sources on the Sun which appear evenly distributed and include solar limb darkening; 2) Cone-optics technique used to add surface specular error to the ray originating sources to determine the apparent ray sources of the reflected sun; 3) choice of facet reflective surface contour -- spherical, ideal parabolic, or toroidal; 4) Gaussian distributions of radial and tangential components of surface slope error added to the surface normals at
3-D TECATE/BREW: Thermal, stress, and birefringent ray-tracing codes for solid-state laser design
Gelinas, R. J.; Doss, S. K.; Nelson, R. G.
1994-07-01
This report describes the physics, code formulations, and numerics that are used in the TECATE (totally Eulerian code for anisotropic thermo-elasticity) and BREW (birefringent ray-tracing of electromagnetic waves) codes for laser design. These codes resolve thermal, stress, and birefringent optical effects in 3-D stationary solid-state systems. This suite of three constituent codes is a package referred to as LASRPAK.
Sheil, Conor; Goncharov, Alexander V.
2013-05-01
A physical model eye was constructed to test the quality of ophthalmic instruments. The accuracy and precision of two commercially available instruments were analysed. For these instruments, a particular model eye was obtained which mimicked the physical properties that would be usually measured e.g. corneal topography or optical path within the human eye. The model eye was designed using relatively simple optical components (e.g. plano-convex lenses) separated by appropriate intraocular distances taken from the literature. The dimensions of the model eye were known a priori: The lenses used in the construction of the model eye were characterised ac cording to values given in the manufacturers' data sheets and also through measurement using an interferometer. The distances between the lens surfaces were calculated using the interferometric data with reverse ray-tracing. Optical paths were calculated as the product of refractive index and axial distance. The errors inherent in mea suring these ocular parameters by different ophthalmic instruments can be considered as producing an erroneous value for the overall refractive power of the eye. The latter is a useful metric for comparing various ophthalmic devices where the direct comparison of quality is not possible or is not practical. For example, a 1% error in anterior corneal radius of curvature will have a more detrimental effect than the same error in posterior corneal radius, due to the relative differences in refractive indices at those surface boundaries. To quantify the error in ocular refractive power, a generic eye model was created in ZEMAX optical design software. The parametric errors were then used to compute the overall error in predicting ocular refractive power, thus highlighting the relative importance of individual errors. This work will help in future determination of acceptable levels of metrological errors in ocular instrumentation.
Shi, Shengxian; Ding, Junfei; New, T. H.; Soria, Julio
2017-07-01
This paper presents a dense ray tracing reconstruction technique for a single light-field camera-based particle image velocimetry. The new approach pre-determines the location of a particle through inverse dense ray tracing and reconstructs the voxel value using multiplicative algebraic reconstruction technique (MART). Simulation studies were undertaken to identify the effects of iteration number, relaxation factor, particle density, voxel-pixel ratio and the effect of the velocity gradient on the performance of the proposed dense ray tracing-based MART method (DRT-MART). The results demonstrate that the DRT-MART method achieves higher reconstruction resolution at significantly better computational efficiency than the MART method (4-50 times faster). Both DRT-MART and MART approaches were applied to measure the velocity field of a low speed jet flow which revealed that for the same computational cost, the DRT-MART method accurately resolves the jet velocity field with improved precision, especially for the velocity component along the depth direction.
Development of a modular CdTe detector plane for gamma-ray burst detection below 100 keV
Ehanno, M.; Amoros, C.; Barret, D.; Lacombe, K.; Pons, R.; Rouaix, G.; Gevin, O.; Limousin, O.; Lugiez, F.; Bardoux, A.; Penquer, A.
2007-01-01
We report on the development of an innovative CdTe detector plane (DPIX) optimized for the detection and localization of gamma-ray bursts in the X-ray band (below 100 keV). DPIX is part of an R&D program funded by the French Space Agency (CNES). DPIX builds upon the heritage of the ISGRI instrument, currently operating with great success on the ESA INTEGRAL mission. DPIX is an assembly of 200 elementary modules (XRDPIX) equipped with 32 CdTe Schottky detectors (4x4 mm2, 1 mm thickness) produc...
Fogle, M; Daly, B; Evans, M; Justiniano, E L; Kovacs, C J; Shinpaugh, J L; Toburen, L H
2001-11-01
Although altered levels of circulating essential trace elements are known to accompany malignant disease, the lack of sensitivity of conventional detection methods has generally limited their study to clinical conditions involving extensive disease (i.e., significant tumor burden). As such, the application of altered trace element levels as potential prognostic guides or as response indicators subsequent to treatment has been of limited use. During this study, proton-induced X-ray emission spectroscopy was evaluated as a tool to determine trace element imbalances in a murine tumor model. Using plasma from C57B1/6 mice bearing the syngeneic Lewis lung carcinoma (LLCa), levels of Fe, Cu, and Zn, as well as changes in the Cu /Zn ratio, were measured in animals carrying an increasing primary tumor burden. The plasma levels of Fe, Cu, and Zn were found to decrease significantly 7 d following implants of LLCa cells with no significant change observed in the Cu/Zn ratio. By d 21, however, an increase in the Cu/Zn ratio was found to accompany increased growth of the LLCa tumor; the plasma levels of Cu had returned to normal levels, whereas both the Fe and Zn plasma levels remained lowered. Collectively, the results suggest that although a net change in individual plasma trace element concentrations might not be accurately associated with tumor growth, a clear relationship was established between the Cu/Zn ratio and tumor size.
The Ray Tracing Analytical Solution within the RAMOD framework. The case of a Gaia-like observer
Crosta, Mariateresa; de Felice, Fernando; Lattanzi, Mario Gilberto
2015-01-01
This paper presents the analytical solution of the inverse ray tracing problem for photons emitted by a star and collected by an observer located in the gravitational field of the Solar System. This solution has been conceived to suit the accuracy achievable by the ESA Gaia satellite (launched on December 19, 2013) consistently with the measurement protocol in General relativity adopted within the RAMOD framework. Aim of this study is to provide a general relativistic tool for the science exploitation of such a revolutionary mission, whose main goal is to trace back star directions from within our local curved space-time, therefore providing a three-dimensional map of our Galaxy. The results are useful for a thorough comparison and cross-checking validation of what already exists in the field of Relativistic Astrometry. Moreover, the analytical solutions presented here can be extended to model other measurements that require the same order of accuracy expected for Gaia.
Kolski, Jeffrey S. [Los Alamos National Laboratory; Barlow, David B. [Los Alamos National Laboratory; Macek, Robert J. [Los Alamos National Laboratory; McCrady, Rodney C. [Los Alamos National Laboratory
2011-01-01
Particle ray tracing through simulated 3D magnetic fields was executed to investigate the effective quadrupole strength of the edge focusing of the rectangular bending magnets in the Los Alamos Proton Storage Ring (PSR). The particle rays receive a kick in the edge field of the rectangular dipole. A focal length may be calculated from the particle tracking and related to the fringe field integral (FINT) model parameter. This tech note introduces the baseline lattice model of the PSR and motivates the need for an improvement in the baseline model's vertical tune prediction, which differs from measurement by .05. An improved model of the PSR is created by modifying the fringe field integral parameter to those suggested by the ray tracing investigation. This improved model is then verified against measurement at the nominal PSR operating set point and at set points far away from the nominal operating conditions. Lastly, Linear Optics from Closed Orbits (LOCO) is employed in an orbit response matrix method for model improvement to verify the quadrupole strengths of the improved model.
Chorus wave-normal statistics in the Earth's radiation belts from ray tracing technique
H. Breuillard
2012-08-01
Full Text Available Discrete ELF/VLF (Extremely Low Frequency/Very Low Frequency chorus emissions are one of the most intense electromagnetic plasma waves observed in radiation belts and in the outer terrestrial magnetosphere. These waves play a crucial role in the dynamics of radiation belts, and are responsible for the loss and the acceleration of energetic electrons. The objective of our study is to reconstruct the realistic distribution of chorus wave-normals in radiation belts for all magnetic latitudes. To achieve this aim, the data from the electric and magnetic field measurements onboard Cluster satellite are used to determine the wave-vector distribution of the chorus signal around the equator region. Then the propagation of such a wave packet is modeled using three-dimensional ray tracing technique, which employs K. Rönnmark's WHAMP to solve hot plasma dispersion relation along the wave packet trajectory. The observed chorus wave distributions close to waves source are first fitted to form the initial conditions which then propagate numerically through the inner magnetosphere in the frame of the WKB approximation. Ray tracing technique allows one to reconstruct wave packet properties (electric and magnetic fields, width of the wave packet in k-space, etc. along the propagation path. The calculations show the spatial spreading of the signal energy due to propagation in the inhomogeneous and anisotropic magnetized plasma. Comparison of wave-normal distribution obtained from ray tracing technique with Cluster observations up to 40° latitude demonstrates the reliability of our approach and applied numerical schemes.
Kohei Arai
2013-01-01
Full Text Available Monte Carlo Ray Tracing: MCRT based sensitivity analysis of the geophysical parameters (the atmosphere and the ocean on Top of the Atmosphere: TOA radiance in visible to near infrared wavelength regions is conducted. As the results, it is confirmed that the influence due to the atmosphere is greater than that of the ocean. Scattering and absorption due to aerosol particles and molecules in the atmosphere is major contribution followed by water vapor and ozone while scattering due to suspended solid is dominant contribution for the ocean parameters.
Cervera, M. A.; Harris, T. J.
2014-01-01
The Defence Science and Technology Organisation (DSTO) has initiated an experimental program, Spatial Ionospheric Correlation Experiment, utilizing state-of-the-art DSTO-designed high frequency digital receivers. This program seeks to understand ionospheric disturbances at scales employ a 3-D magnetoionic Hamiltonian ray tracing engine, developed by DSTO, to (1) model the various disturbance features observed on both the O and X polarization modes in our QVI data and (2) understand how they are produced. The ionospheric disturbances which produce the observed features were modeled by perturbing the ionosphere with atmospheric gravity waves.
Pujol Nadal, Ramon; Martínez Moll, Víctor
2013-10-20
Fixed-mirror solar concentrators (FMSCs) use a static reflector and a moving receiver. They are easily installable on building roofs. However, for high-concentration factors, several flat mirrors would be needed. If curved mirrors are used instead, high-concentration levels can be achieved, and such a solar concentrator is called a curved-slats fixed-mirror solar concentrator (CSFMSC), on which little information is available. Herein, a methodology is proposed to characterize the CSFMSC using 3D ray-tracing tools. The CSFMSC shows better optical characteristics than the FMSC, as it needs fewer reflector segments for achieving the same concentration and optical efficiency.
Chistyakov, Vyacheslav
2015-01-01
Aimed toward researchers and graduate students familiar with elements of functional analysis, linear algebra, and general topology; this book contains a general study of modulars, modular spaces, and metric modular spaces. Modulars may be thought of as generalized velocity fields and serve two important purposes: generate metric spaces in a unified manner and provide a weaker convergence, the modular convergence, whose topology is non-metrizable in general. Metric modular spaces are extensions of metric spaces, metric linear spaces, and classical modular linear spaces. The topics covered include the classification of modulars, metrizability of modular spaces, modular transforms and duality between modular spaces, metric and modular topologies. Applications illustrated in this book include: the description of superposition operators acting in modular spaces, the existence of regular selections of set-valued mappings, new interpretations of spaces of Lipschitzian and absolutely continuous mappings, the existe...
Ray-tracing formulas for refraction and internal reflection in uniaxial crystals.
Beyerle, G; McDermid, I S
1998-12-01
Formulas for the calculation of the direction cosines of refracted and internally reflected rays in anisotropic uniaxial crystals are presented. The method is based on a transformation to a nonorthonormal coordinate system in which the normal surface associated with the extraordinary ray is of spherical shape. A numerical example for the case of refraction and internal reflection in calcite is given.
Junjie Ma
2015-05-01
Full Text Available Total-reflection X-ray fluorescence (TXRF has achieved remarkable success with the advantages of simultaneous multi-element analysis capability, decreased background noise, no matrix effects, wide dynamic range, ease of operation, and potential of trace analysis. Simultaneous quantitative online analysis of trace heavy metals is urgently required by dynamic environmental monitoring and management, and TXRF has potential in this application domain. However, it calls for an online analysis scheme based on TXRF as well as a robust and rapid quantification method, which have not been well explored yet. Besides, spectral overlapping and background effects may lead to loss of accuracy or even faulty results during practical quantitative TXRF analysis. This paper proposes an intelligent, multi-element quantification method according to the established online TXRF analysis platform. In the intelligent quantification method, collected characteristic curves of all existing elements and a pre-estimated background curve in the whole spectrum scope are used to approximate the measured spectrum. A novel hybrid algorithm, PSO-RBFN-SA, is designed to solve the curve-fitting problem, with offline global optimization and fast online computing. Experimental results verify that simultaneous quantification of trace heavy metals, including Cr, Mn, Fe, Co, Ni, Cu and Zn, is realized on the online TXRF analysis platform, and both high measurement precision and computational efficiency are obtained.
Solis, C.; Issac O, K. [Instituto de Fisica, Departamento de Fisica Experimental, UNAM, Apartado Postal 20-364, 01000 Mexico D. F. (Mexico); Martinez, A.; Lavoisier, E.; Martinez, M. A. [Instituto de Investigaciones en Materiales, UNAM, Ciudad Universitaria, 04510 Mexico D. F. (Mexico)
2008-02-15
The growing urban and tourist activity in the Mexican Caribbean coasts has resulted in an increase of chemical substances, metals in particular, discharged to the coastal waters. In order to reach an adequate management and conservation of these marine ecosystems it is necessary to perform an inventory of the actual conditions that reflect the vulnerability and the level of damage. Sea-grasses are considered good biological indicators of heavy metal contamination in marine systems. The goal of this preliminary work is to evaluate the concentrations of trace metals such as Cr, Mn, Fe, Co, Cu, Zn, and Pb in Thalassia testudinum, a very common sea-grass in the Mexican Caribbean Sea. Samples were collected from several locations in the coasts of the Yucatan Peninsula: Holbox, Blanquizal and Punta Allen, areas virtually uninfluenced by anthropogenic activities. Trace elements in different part plants were determined by particle induced X-ray emission (PIXE). This is a very suitable technique since it offers a fast, accurate and multi-element analysis. Also, the analysis by PIXE can be performed directly on powdered leaves without a laborious sample preparation. The trace metal concentration determined in sea-grasses growing in Caribbean generally fall in the range of the lowest valuables reported for sea grasses from the Gulf of Mexico. The results indicate that the studied areas do not present contamination by heavy metals. (Author)
Ma, Junjie; Wang, Yeyao; Yang, Qi; Liu, Yubing; Shi, Ping
2015-05-06
Total-reflection X-ray fluorescence (TXRF) has achieved remarkable success with the advantages of simultaneous multi-element analysis capability, decreased background noise, no matrix effects, wide dynamic range, ease of operation, and potential of trace analysis. Simultaneous quantitative online analysis of trace heavy metals is urgently required by dynamic environmental monitoring and management, and TXRF has potential in this application domain. However, it calls for an online analysis scheme based on TXRF as well as a robust and rapid quantification method, which have not been well explored yet. Besides, spectral overlapping and background effects may lead to loss of accuracy or even faulty results during practical quantitative TXRF analysis. This paper proposes an intelligent, multi-element quantification method according to the established online TXRF analysis platform. In the intelligent quantification method, collected characteristic curves of all existing elements and a pre-estimated background curve in the whole spectrum scope are used to approximate the measured spectrum. A novel hybrid algorithm, PSO-RBFN-SA, is designed to solve the curve-fitting problem, with offline global optimization and fast online computing. Experimental results verify that simultaneous quantification of trace heavy metals, including Cr, Mn, Fe, Co, Ni, Cu and Zn, is realized on the online TXRF analysis platform, and both high measurement precision and computational efficiency are obtained.
Comparison of a 3-D GPU-Assisted Maxwell Code and Ray Tracing for Reflectometry on ITER
Gady, Sarah; Kubota, Shigeyuki; Johnson, Irena
2015-11-01
Electromagnetic wave propagation and scattering in magnetized plasmas are important diagnostics for high temperature plasmas. 1-D and 2-D full-wave codes are standard tools for measurements of the electron density profile and fluctuations; however, ray tracing results have shown that beam propagation in tokamak plasmas is inherently a 3-D problem. The GPU-Assisted Maxwell Code utilizes the FDTD (Finite-Difference Time-Domain) method for solving the Maxwell equations with the cold plasma approximation in a 3-D geometry. Parallel processing with GPGPU (General-Purpose computing on Graphics Processing Units) is used to accelerate the computation. Previously, we reported on initial comparisons of the code results to 1-D numerical and analytical solutions, where the size of the computational grid was limited by the on-board memory of the GPU. In the current study, this limitation is overcome by using domain decomposition and an additional GPU. As a practical application, this code is used to study the current design of the ITER Low Field Side Reflectometer (LSFR) for the Equatorial Port Plug 11 (EPP11). A detailed examination of Gaussian beam propagation in the ITER edge plasma will be presented, as well as comparisons with ray tracing. This work was made possible by funding from the Department of Energy for the Summer Undergraduate Laboratory Internship (SULI) program. This work is supported by the US DOE Contract No.DE-AC02-09CH11466 and DE-FG02-99-ER54527.
Tsujimura, T., Ii; Kubo, S.; Takahashi, H.; Makino, R.; Seki, R.; Yoshimura, Y.; Igami, H.; Shimozuma, T.; Ida, K.; Suzuki, C.; Emoto, M.; Yokoyama, M.; Kobayashi, T.; Moon, C.; Nagaoka, K.; Osakabe, M.; Kobayashi, S.; Ito, S.; Mizuno, Y.; Okada, K.; Ejiri, A.; Mutoh, T.
2015-11-01
The central electron temperature has successfully reached up to 7.5 keV in large helical device (LHD) plasmas with a central high-ion temperature of 5 keV and a central electron density of 1.3× {{10}19} m-3. This result was obtained by heating with a newly-installed 154 GHz gyrotron and also the optimisation of injection geometry in electron cyclotron heating (ECH). The optimisation was carried out by using the ray-tracing code ‘LHDGauss’, which was upgraded to include the rapid post-processing three-dimensional (3D) equilibrium mapping obtained from experiments. For ray-tracing calculations, LHDGauss can automatically read the relevant data registered in the LHD database after a discharge, such as ECH injection settings (e.g. Gaussian beam parameters, target positions, polarisation and ECH power) and Thomson scattering diagnostic data along with the 3D equilibrium mapping data. The equilibrium map of the electron density and temperature profiles are then extrapolated into the region outside the last closed flux surface. Mode purity, or the ratio between the ordinary mode and the extraordinary mode, is obtained by calculating the 1D full-wave equation along the direction of the rays from the antenna to the absorption target point. Using the virtual magnetic flux surfaces, the effects of the modelled density profiles and the magnetic shear at the peripheral region with a given polarisation are taken into account. Power deposition profiles calculated for each Thomson scattering measurement timing are registered in the LHD database. The adjustment of the injection settings for the desired deposition profile from the feedback provided on a shot-by-shot basis resulted in an effective experimental procedure.
Sarmah, Nabin; Richards, Bryce S; Mallick, Tapas K
2011-07-01
We present a detailed design concept and optical performance evaluation of stationary dielectric asymmetric compound parabolic concentrators (DiACPCs) using ray-tracing methods. Three DiACPC designs, DiACPC-55, DiACPC-66, and DiACPC-77, of acceptance half-angles (0° and 55°), (0° and 66°), and (0° and 77°), respectively, are designed in order to optimize the concentrator for building façade photovoltaic applications in northern latitudes (>55 °N). The dielectric concentrator profiles have been realized via truncation of the complete compound parabolic concentrator profiles to achieve a geometric concentration ratio of 2.82. Ray-tracing simulation results show that all rays entering the designed concentrators within the acceptance half-angle range can be collected without escaping from the parabolic sides and aperture. The maximum optical efficiency of the designed concentrators is found to be 83%, which tends to decrease with the increase in incidence angle. The intensity is found to be distributed at the receiver (solar cell) area in an inhomogeneous pattern for a wide range of incident angles of direct solar irradiance with high-intensity peaks at certain points of the receiver. However, peaks become more intense for the irradiation incident close to the extreme acceptance angles, shifting the peaks to the edge of the receiver. Energy flux distribution at the receiver for diffuse radiation is found to be homogeneous within ±12% with an average intensity of 520 W/m².
Custo, Graciela [Unidad de Actividad Quimica, Comision Nacional de Energia Atomica, Av. Gral Paz 1499 (B1650KNA) San Martin, Buenos Aires (Argentina); Litter, Marta I. [Unidad de Actividad Quimica, Comision Nacional de Energia Atomica, Av. Gral Paz 1499 (B1650KNA) San Martin, Buenos Aires (Argentina); Escuela de Posgrado, Universidad de General San Martin, San Lorenzo 3391 Villa Ballester, 1653. Prov. de Buenos Aires (Argentina); Rodriguez, Diana [Universidad Nacional de Lujan, Ruta 5 y 7. Prov. de Buenos Aires (Argentina); Vazquez, Cristina [Unidad de Actividad Quimica, Comision Nacional de Energia Atomica, Av. Gral Paz 1499 (B1650KNA) San Martin, Buenos Aires (Argentina) and Laboratorio de Quimica de Sistemas Heterogeneos, Facultad de Ingenieria, Universidad de Buenos Aires, P. Colon 850 (C1063ACU), Buenos Aires (Argentina)]. E-mail: Cristina.Vazquez@cnea.gov.ar
2006-11-15
It is well known that Hg species cause high noxious effects on the health of living organisms even at very low levels (5 {mu}g/L). Quantification of this element is an analytical challenge due to the peculiar physicochemical properties of all Hg species. The regulation of the maximal allowable Hg concentration led to search for sensitive methods for its determination. Total reflection X-ray fluorescence is a proved instrumental analytical tool for the determination of trace elements. In this work, the use of total reflection X-ray fluorescence for Hg quantification is investigated. However, experimental determination by total reflection X-ray fluorescence requires depositing a small volume of sample on the reflector and evaporation of the solvent until dryness to form a thin film. Because of volatilization of several Hg forms, a procedure to capture these volatile species in liquid samples by using complexing agents is proposed. Acetate, oxalic acid, ethylenediaminetetracetic acid and ammonium pyrrolidine-dithiocarbamate were assayed for trapping the analytes into the solution during the preparation of the sample and onto the reflector during total reflection X-ray fluorescence measurements. The proposed method was applied to evaluate Hg concentration during TiO{sub 2}-heterogeneous photocatalysis, one of the most known advanced oxidation technologies. Advanced oxidation technologies are processes for the treatment of effluents in waters and air that involve the generation of very active oxidative and reductive species. In heterogeneous photocatalysis, Hg is transformed to several species under ultraviolet illumination in the presence of titanium dioxide. Total reflection X-ray fluorescence was demonstrated to be applicable in following the extent of the heterogeneous photocatalysis reaction by determining non-transformed Hg in the remaining solution.
Custo, Graciela; Litter, Marta I.; Rodríguez, Diana; Vázquez, Cristina
2006-11-01
It is well known that Hg species cause high noxious effects on the health of living organisms even at very low levels (5 μg/L). Quantification of this element is an analytical challenge due to the peculiar physicochemical properties of all Hg species. The regulation of the maximal allowable Hg concentration led to search for sensitive methods for its determination. Total reflection X-ray fluorescence is a proved instrumental analytical tool for the determination of trace elements. In this work, the use of total reflection X-ray fluorescence for Hg quantification is investigated. However, experimental determination by total reflection X-ray fluorescence requires depositing a small volume of sample on the reflector and evaporation of the solvent until dryness to form a thin film. Because of volatilization of several Hg forms, a procedure to capture these volatile species in liquid samples by using complexing agents is proposed. Acetate, oxalic acid, ethylenediaminetetracetic acid and ammonium pyrrolidine-dithiocarbamate were assayed for trapping the analytes into the solution during the preparation of the sample and onto the reflector during total reflection X-ray fluorescence measurements. The proposed method was applied to evaluate Hg concentration during TiO 2-heterogeneous photocatalysis, one of the most known advanced oxidation technologies. Advanced oxidation technologies are processes for the treatment of effluents in waters and air that involve the generation of very active oxidative and reductive species. In heterogeneous photocatalysis, Hg is transformed to several species under ultraviolet illumination in the presence of titanium dioxide. Total reflection X-ray fluorescence was demonstrated to be applicable in following the extent of the heterogeneous photocatalysis reaction by determining non-transformed Hg in the remaining solution.
Nosikov, I. A.; Klimenko, M. V.; Bessarab, P. F.; Zhbankov, G. A.
2017-07-01
Point-to-point ray tracing is an important problem in many fields of science. While direct variational methods where some trajectory is transformed to an optimal one are routinely used in calculations of pathways of seismic waves, chemical reactions, diffusion processes, etc., this approach is not widely known in ionospheric point-to-point ray tracing. We apply the Nudged Elastic Band (NEB) method to a radio wave propagation problem. In the NEB method, a chain of points which gives a discrete representation of the radio wave ray is adjusted iteratively to an optimal configuration satisfying the Fermat's principle, while the endpoints of the trajectory are kept fixed according to the boundary conditions. Transverse displacements define the radio ray trajectory, while springs between the points control their distribution along the ray. The method is applied to a study of point-to-point ionospheric ray tracing, where the propagation medium is obtained with the International Reference Ionosphere model taking into account traveling ionospheric disturbances. A 2-dimensional representation of the optical path functional is developed and used to gain insight into the fundamental difference between high and low rays. We conclude that high and low rays are minima and saddle points of the optical path functional, respectively.
改进的地震模型初值射线追踪方法%Improved Seismic Model Initial Value Ray Tracing Method
贺中银; 高阳
2011-01-01
The initial value ray tracing method is one of major method in modem ray tracing methods. It overcomes time-consuming computing efficiency in two spots ray tracing. Based on eikonal equation, improved initial value ray tracing, that is using square slowness to replace velocity parameters in model, make eikonal equation produces analytic solutions, a step further to derive computing expressions of reflection and transmission slowness vectors when the ray confiont with interface, and reflection and transmission coefficients function expressions. Through ray tracings of simple two layered interface syncline model and complex multiple layered salt-dome model, have shown the improvement of initial value ray tracing by comparison with Runge-Kutta discrete numerical solution, not only improved ray tracing efficiency (about 10 times), but also extended limit for the use of ray tracing method.%初值射线追踪方法是现代射线追踪方法中的一个很重要的理论,它克服了两点法射线追踪方法耗时的计算效率问题.以程函方程为基础,对初值射线追踪方法进行改进,即利用平方慢度来替换模型中的速度参数,使得程函方程产生解析解,从而进一步导出当射线遇到界面时的反射和透射慢度向量的计算表达式,以及反射、透射系数的函数表达式.通过对简单的两层界面向斜模型及复杂的多层盐丘模型的射线追踪,表明该初值射线追踪方法的改进相比于以往的龙格库塔离散数值解法,不但使射线追踪效率得到了大幅度提高(10倍左右),且也扩大了射线法使用范围.
A Three-Dimensional Ray-Tracing Study of R-X Mode Waves during High Geomagnetic Activity
XIAO Fu-Liang; CHEN Lun-Jin; ZHENG Hui-Nan; WANG Shui; GUO Jun
2008-01-01
We further present a three-dimensional(3D)ray-tracing study on the propagation characteristic of the superluminous R-X mode waves during high geomagnetic activity following our recent two-dimensional results [J.Geophys.Res.112(2007)A10214].We perform numerical calculations for this mode which originates at specific altitude r=2.0RE in the souice cavity along a 70°night geomagnetic field line.We demonstrate that the ray path of the R-X mode is essentially governed by the azimuthal angle of the wave vector k.Ray paths starting with azimuthal angle 180°(or in the meridian plane)can reach the lowest latitude,but stay at relatively higher latitudes with the azimuthal anglas other than 180°(or off the meridian plane).The results further supports the previous finding that the R-X mode may be physically present in the radiation belts under appropriate conditions.
Architecture of a highly modular lighting simulation system
CERN. Geneva
2014-01-01
This talk will discuss the challenges before designing a highly modular, parallel, heterogeneous rendering system and their solutions. It will review how different lighting simulation algorithms could be combined to work together using an unified framework. We will discuss how the system can be instrumented for collecting data about the algorithms' runtime performance. The talk includes an overview of how collected data could be visualised in the computational domain of the lighting algorithms and be used for visual debugging and analysis. About the speaker Hristo Lesev has been working in the software industry for the last ten years. He has taken part in delivering a number of desktop and mobile applications. Computer Graphics programming is Hristo's main passion and he has experience writing extensions for 3D software like 3DS Max, Maya, Blender, Sketchup, and V-Ray. Since 2006 Hristo teaches Photorealistic Ray Tracing in the Faculty of Mathematics and Informatics at the Paisii Hilendarski...
Aranda, Pedro R.; Moyano, Susana; Martinez, Luis D.; De Vito, Irma E. [Universidad Nacional de San Luis, Facultad de Quimica, Bioquimica y Farmacia, Area de Quimica Analitica, Instituto de Quimica de San Luis (INQUISAL - CONICET), San Luis (Argentina)
2010-09-15
A new, simple, and selective method for preconcentration and determination of Cr(VI) in aqueous samples. After adsorption in ''batch mode'' on Aliquat 336-AC, determinations were made directly on the solid by X-ray fluorescence spectrometry, which had the advantage of not requiring the step of elution of the chromium retained. The enrichment factor was calculated considering that the tablets obtained from 10 mL solution of Cr(VI) (1000 {mu}g L{sup -1}) had a final thickness of 0.64 mm and a diameter of 16.7 mm; the volume deposited on the pellet was 0.14 cm{sup 3}. The preconcentration factor obtained was 71-fold, which was highly satisfactory for chromium trace analysis by XRF. Finally, the method was successfully applied to the determination of Cr(VI) in drinking water samples. (orig.)
A model of the AGS based on stepwise ray-tracing through the measured field maps of the main magnets
Dutheil Y.; Meot, F.; Tsoupas, N.
2012-05-20
Two-dimensional mid-plane magnetic field maps of two of the main AGS magnets were produced, from Hall probe measurements, for a series of different current settings. The analysis of these data yielded the excitation functions [1] and the harmonic coefficients [2] of the main magnets which have been used so far in all the models of the AGS. The constant increase of the computation power makes it possible today to directly use a stepwise raytracing through these measured field maps with a reasonable computation time. We describe in detail how these field maps have allowed the generation of models of the 6 different types of AGS main magnets, and how they are being handled with the Zgoubi ray-tracing code [3]. We give and discuss a number of results obtained regarding both beam and spin dynamics in the AGS, and we provide comparisons with other numerical and analytical modelling methods.
Christophe Lièbe
2010-01-01
Full Text Available This paper presents a new software for design of through-the-wall imaging radars. The first part describes the evolution of a ray tracing simulator, originally designed for propagation of narrowband signals, and then for ultra-wideband signals. This simulator allows to obtain temporal channel response to a wide-band emitter (3 GHz to 10 GHz. An experimental method is also described to identify the propagation paths. Simulation results are compared to propagation experiments under the same conditions. Different configurations are tested and then discussed. Finally, a configuration of through-the-wall imaging radar is proposed, with different antennas patterns and different targets. Simulated images will be helpful for understanding the experiment obtained images.
He, Wenjun; Fu, Yuegang; Liu, Zhiying; Zhang, Lei; Wang, Jiake; Zheng, Yang; Li, Yahong
2017-03-01
The polarization aberrations of a complex optical system with multi-element lens have been investigated using a 3D polarization aberration function. The 3D polarization ray-tracing matrix has been combined with the optical path difference to obtain a 3D polarization aberration function, which avoids the need for a complicated phase unwrapping process. The polarization aberrations of a microscope objective have been analyzed to include, the distributions of 3D polarization aberration functions, diattenuation aberration, retardance aberration, and polarization-dependent intensity on the exit pupil. Further, the aberrations created by the field of view and the coating on the distribution rules of 3D polarization aberration functions are discussed in detail. Finally a novel appropriate field of view and wavelength correction is proposed for a polarization aberration function which optimizes the image quality of a multi-element optical system.
Nugent, Allen H; Bertram, Christopher D
2010-02-01
Prediction of the effects of refractive index (RI) mismatch on laser Doppler anemometer (LDA) measurements within a curvilinear cavity (an artificial ventricle) was achieved by developing a general technique for modelling the paths of the convergent beams of the LDA system using 3D vector geometry. Validated by ray tracing through CAD drawings, the predicted maximum tolerance in RI between the solid model and the working fluid was +/- 0.0005, equivalent to focusing errors commensurate with the geometric and alignment uncertainties associated with the flow model and the LDA arrangement. This technique supports predictions of the effects of refraction within a complex geometry. Where the RI mismatch is unavoidable but known, it is possible not only to calculate the true position of the measuring volume (using the probe location and model geometry), but also to estimate degradation in signal quality arising from differential displacement and refraction of the laser beams.
Chevallier, P.; Wang, J.; Jehanno, C.; Maurette, M.; Sutton, S. R.
1986-01-01
Synchrotron X-ray fluorescence spectra of unpolished iron and chondritic spheres extracted from sediments collected on the melt zone of the Greenland ice cap allow the analysis of Ni, Cu, Zn, Ga, Ge, Pb, and Se with minimum detection limits on the order of several parts per million. All detected elements are depleted relative to chondritic abundance with the exception of Pb, which shows enrichments up to a factor of 500. An apparent anticorrelation between the Ni-content and trace element concentration was observed in both types of spherules. The fractionation patterns of the iron and chondritic spheres are not complementary and consequently the two iron spheres examined in this study are unlikely to result from ejection of globules of Fe/Ni from parent chondritic micrometeoroids.
Sangita Dhara; N L Misra
2011-02-01
Applicability of total reﬂection X-ray ﬂuorescence (TXRF) spectrometry for trace elemental analysis of rainwater samples was studied. The study was used to develop these samples as rainwater standards by the National University of Singapore (NUS). Our laboratory was one of the participants to use TXRF for this study. The rainwater sample obtained from NUS was analysed by TXRF and the trace elements Mn, Fe, Ni, Cu, Zn, V and Pb were determined as required by the NUS. The average precision was found to be within 16% and the TXRF-determined elemental concentrations of these elements were below 20 /l. The average deviation of TXRFdetermined values from the certiﬁed values were 20% (excluding the deviation for Fe and V which were comparatively high). Apart from the above elements, S, K, Ca, Rb, Sr, Ba and Br were also determined by TXRF and were found to be in the range of 0.2 to 191 /l. TXRF-determined values of our laboratory played an important role in the certiﬁcation of concentration of seven elements in this rainwater sample which was later developed as a rainwater standard.
Song Fu
2015-01-01
Full Text Available Although the uniform theory of diffraction (UTD could be theoretically applied to arbitrarilyshaped convex objects modeled by nonuniform rational B-splines (NURBS, one of the great challenges in calculation of the UTD surface diffracted fields is the difficulty in determining the geodesic paths along which the creeping waves propagate on arbitrarilyshaped NURBS surfaces. In differential geometry, geodesic paths satisfy geodesic differential equation (GDE. Hence, in this paper, a general and efficient adaptive variable step Euler method is introduced for solving the GDE on arbitrarilyshaped NURBS surfaces. In contrast with conventional Euler method, the proposed method employs a shape factor (SF ξ to efficiently enhance the accuracy of tracing and extends the application of UTD for practical engineering. The validity and usefulness of the algorithm can be verified by the numerical results.
Dahl, Tais W.; Ruhl, Micha; Hammarlund, Emma U.
2013-01-01
Elevated molybdenum (Mo) contents in organic-rich sediments are indicative of deposition from an anoxic and sulfide-rich (euxinic) water-column. This can be used for tracing past euxinic conditions in ancient oceans from sedimentary archives. Conventional analytical detection of elevated molybdenum...... with Mo: 47 ppm and NIST-2702 with Mo: 10 ppm) for analytical control. Analytical precision (1 sigma) after 30, 120, and 300 seconds of measuring time was 4, 2, and 1 ppm, with a respective detection limit of 11, 5, 3 ppm (3 sigma, noise level). The data were accurate to within the given precision (1...... sigma) after a daily calibration to samples covering a range of Mo concentrations from 0 to >30 ppm. Hand-held XRF equipment also allows Mo measurements directly on fresh rock surfaces, both in the field and under laboratory conditions. Rock-samples from a Cambrian drill core closely match ICPMS...
Pingitore, N. E.; Cruz-Jimenez, G.; Price, T. D.
2001-12-01
X-ray absorption spectroscopy (XAS) affords the opportunity to probe the atomic environment of trace elements in human bone. We are using XAS to investigate the mode(s) of incorporation of Sr, Zn, Pb, and Ba in both modern and ancient (and thus possibly altered) human and animal bone. Because burial and diagenesis may add trace elements to bone, we performed XAS analysis on samples of pristine contemporary and ancient, buried human and animal bone. We assume that deposition of these elements during burial occurs by processes distinct from those in vivo, and this will be reflected in their atomic environments. Archaeologists measure strontium in human and animal bone as a guide to diet. Carnivores show lower Sr/Ca ratios than their herbivore prey due to discrimination against Sr relative to Ca up the food chain. In an initial sample suite no difference was observed between modern and buried bone. Analysis of additional buried samples, using a more sensitive detector, revealed significant differences in the distance to the second and third neighbors of the Sr in some of the buried samples. Distances to the first neighbor, oxygen, were similar in all samples. Zinc is also used in paleo-diet studies. Initial x-ray absorption spectroscopy of a limited suite of bones did not reveal any differences between modern and buried samples. This may reflect the limited number of samples examined or the low levels of Zn in typical aqueous solutions in soils. Signals from barium and lead were too low to record useful XAS spectra. Additional samples will be studied for Zn, Ba, and Pb. We conducted our XAS experiments on beam lines 4-1 and 4-3 at the Stanford Synchrotron Radiation Laboratory. Data were collected in the fluorescence mode, using a Lytle detector and appropriate filter, and a solid state, 13-element Ge-detector.
Trace element determination in amniotic fluid by total reflection X-ray fluorescence
Greaves, E.D.; Sajo-Bohus, L.; Castelli, C.; Borgerg, C. [Universidad Simon Bolivar, Caracas (Venezuela); Meitin, J.; Liendo, J.
1995-03-01
A new method is reported for the determination of Fe, Cu, Zn, and Br in amniotic fluid (AF) by Total Reflection X-Ray Fluorescence. The irradiation of AF samples with monochromatic X-Rays reduces the scattering background from the organic matrix and avoids the need for sample digestion. Sample manipulation is reduced to centrifuging and adding cobalt as internal standard. Lower detection limits obtained are 109, 53, 44 and 37 ppb for Fe, Cu, Zn and Br respectively. Measurement precision depends on element concentrations and can be as low as 1.5% SD. Results of the analysis of 34 AF samples from Venezuelan pregnant patients agree with previously reported ranges of Fe, Cu and Zn. Other elements observed but not quantified are Cl, K, Ca in all spectra and Pb and Sr in some of them. (author).
Martinez, T. [National University of Mexico, Faculty of Chemistry, Building D, CU (O4510) Mexico, D.F. Mexico (Mexico)], E-mail: tmc@servidor.unam.mx; Lartigue, J. [National University of Mexico, Faculty of Chemistry, Building D, CU (O4510) Mexico, D.F. Mexico (Mexico); Zarazua, G.; Avila-Perez, P. [National Institute of Nuclear Research. Carr. Mexico-Toluca Km 36.5, (52045) Salazar, Ocoyoacac, Edo. de Mexico (Mexico); Navarrete, M. [National University of Mexico, Faculty of Chemistry, Building D, CU (O4510) Mexico, D.F. Mexico (Mexico); Tejeda, S. [National Institute of Nuclear Research. Carr. Mexico-Toluca Km 36.5, (52045) Salazar, Ocoyoacac, Edo. de Mexico (Mexico)
2008-12-15
Many studies have identified an important number of toxic elements along with organic carcinogen molecules and radioactive isotopes in tobacco. In this work we have analyzed by Total Reflection X-Ray Fluorescence 9 brands of cigarettes being manufactured and distributed in the Mexican market. Two National Institute of Standards and Technology standards and a blank were equally treated at the same time. Results show the presence of some toxic elements such as Pb and Ni. These results are compared with available data for some foreign brands, while their implications for health are discussed. It can be confirmed that the Total Reflection X-Ray Fluorescence method provides precise (reproducible) and accuracy (trueness) data for 15 elements concentration in tobacco samples.
周庆华; 史建魁; 肖伏良
2011-01-01
A three-dimensional ray tracing study of a whistler-mode chorus is conducted for different geomagnetic activities by using a global core plasma density model. For the upperband chorus, the initial azimuthal wave angle affects slightly the projection of ray trajectories onto the plane （Z, √（x^2 ＋ y^2））, but controls the longitudinal propagation. The trajectory of the upper-band chorus is strongly associated with the plasmapause and the magnetic local time （MLT） of chorus source region. For the high geomagnetic activity, the chorus trajectory moves inward together with the plasmapause. In the bulge region, the plasmapause extends outward, while the chorus trajectory moves outward together with the plasmapause. For moderately or high geomagnetic activity, the lower-band chorus suffers low hybrid resonance （LHR） reflection before it reaches the plasmapause, leading to a weak correlation with the geomagnetic activity and magnetic local time of the chorus source region. For low geomagnetic activity, the lower-band chorus may be reflected firstly at the plasmapause instead of suffering LHR reflection, exhibiting a propagation characteristic similar to that of the upper-band chorus. The results provide a new insight into the propagation characteristics of the chorus for different geomagnetic activities and contribute to further understanding of the acceleration of energetic electron by a chorus wave.
Characterizing trace metal impurities in optical waveguide materials using x-ray absorption
Citrin, P.H.; Northrup, P.A.; Atkins, R.M.; Niu, L.; Marcus, M.A.; Jacobson, D.C. [Lucent Technologies, Murray Hill, NJ (United States). Bell Labs.; Glodis, P.F. [Lucent Technologies, Norcross, GA (United States). Bell Labs.
1998-12-31
X-ray absorption measurements are described for identifying metal impurities in silica preforms, the rod-like starting materials from which hair-like optical fibers are drawn. The results demonstrate the effectiveness of this approach as a non-destructive, quantitative, element-selective, position-sensitive, and chemical-state-specific means for characterizing transition metals in the concentration regime of parts per billion.
Alternative methods for ray tracing in uniaxial media. Application to negative refraction
Bellver-Cebreros, Consuelo; Rodriguez-Danta, Marcelo
2007-03-01
In previous papers [C. Bellver-Cebreros, M. Rodriguez-Danta, Eikonal equation, alternative expression of Fresnel's equation and Mohr's construction in optical anisotropic media, Opt. Commun. 189 (2001) 193; C. Bellver-Cebreros, M. Rodriguez-Danta, Internal conical refraction in biaxial media and graphical plane constructions deduced from Mohr's method, Opt. Commun. 212 (2002) 199; C. Bellver-Cebreros, M. Rodriguez-Danta, Refraccion conica externa en medios biaxicos a partir de la construccion de Mohr, Opt. Pura AppliE 36 (2003) 33], the authors have developed a method based on the local properties of dielectric permittivity tensor and on Mohr's plane graphical construction in order to study the behaviour of locally plane light waves in anisotropic media. In this paper, this alternative methodology is compared with the traditional one, by emphasizing the simplicity of the former when studying ray propagation through uniaxial media (comparison is possible since, in this case, traditional construction becomes also plane). An original and simple graphical method is proposed in order to determine the direction of propagation given by the wave vector from the knowledge of the extraordinary ray direction (given by Poynting vector). Some properties of light rays in these media not described in the literature are obtained. Finally, two applications are considered: a description of optical birefringence under normal incidence and the study of negative refraction in uniaxial media.
Understanding Socio Technical Modularity
Thuesen, Christian Langhoff; Kudsk, Anders; Hvam, Lars
2011-01-01
Modularity has gained an increasing popularity as a central concept for exploring product structure, process structure, organization structure and supply chain structure. With the offset in system theory the predominant understanding of modularity however faces difficulties in explaining the social...... Theory in particular. By formulating modularity from an ANT perspective covering social, material and process aspects, the modularity of a socio-technical system can be understood as an entanglement of product, process, organizational and institutional modularity. The theoretical framework is illustrated...
Viridi, Sparisoma
2013-01-01
Trace of ray deviated by a prism, which is common in a TIR (total internal reflection) measurement system, is sometimes difficult to manage, especially if the prism is an equilateral right angle prism (ERAP). The point where the ray is reflected inside the right-angle prism is also changed as the angle of incident ray changed. In an ATR (attenuated total reflectance) measurement system, range of this point determines size of sample. Using JavaScript and HTML5 model and visualization of ray tracing deviated by an ERAP is perform and reported in this work. Some data are obtained from this visualization and an empirical relations between angle of incident ray source \\theta_S, angle of ray detector hand \\theta_D, and angle of ray detector \\theta'_D are presented for radial position of ray source R_S, radial position of ray detector R_D, height of right-angle prism t, and refractive index of the prism n. Keywords: deviation angle, equilateral right angle prism, total internal reflection, JavaScript, HTML5.
Logarithmic conformal field theory, log-modular tensor categories and modular forms
Creutzig, Thomas
2016-01-01
The two pillars of rational conformal field theory and rational vertex operator algebras are modularity of characters on the one hand and its interpretation of modules as objects in a modular tensor category on the other one. Overarching these pillars is the Verlinde formula. In this paper we consider the more general class of logarithmic conformal field theories and $C_2$-cofinite vertex operator algebras. We suggest that their modular pillar are trace functions with insertions corresponding to intertwiners of the projective cover of the vacuum, and that the categorical pillar are finite tensor categories $\\mathcal C$ which are ribbon and whose double is isomorphic to the Deligne product $\\mathcal C\\otimes \\mathcal C^{opp}$. Overarching these pillars is then a logarithmic variant of Verlinde's formula. Numerical data realizing this are the modular $S$-matrix and modified traces of open Hopf links. The representation categories of $C_2$-cofinite and logarithmic conformal field theories that are fairly well un...
New ray-tracing capabilities for the development of silicon pore optics
Vacanti, Giuseppe; Barrière, Nicolas; Chatbi, Abdelhakim; Collon, Maximilien; Günther, Ramses; Yanson, Alexei; Vervest, Mark; Bavdaz, Marcos; Wille, Eric
2015-09-01
The Geant4 based ray-tracer used to support the development of Silicon Pore Optics is being extended to take into account more subtle effects that affect the performance of the optics, like thermo-mechanical stresses and detailed surface metrology. Its performance has also been increased to make it possible to simulate rapidly and in detail the optics of Athena so that various possible configurations can be explored and characterized providing important feedback to the development and system teams. In this paper we report on the state of the development.
Wandzilak, Aleksandra; Czyzycki, Mateusz; Radwanska, Edyta; Adamek, Dariusz; Geraki, Kalotina; Lankosz, Marek
2015-12-01
Neoplastic and healthy brain tissues were analysed to discern the changes in the spatial distribution and overall concentration of elements using micro X-ray fluorescence spectroscopy. High-resolution distribution maps of minor and trace elements such as P, S, Cl, K, Ca, Fe, Cu and Zn made it possible to distinguish between homogeneous cancerous tissue and areas where some structures could be identified, such as blood vessels and calcifications. Concentrations of the elements in the selected homogeneous areas of brain tissue were compared between tumours with various malignancy grades and with the controls. The study showed a decrease in the average concentration of Fe, P, S and Ca in tissues with high grades of malignancy as compared to the control group, whereas the concentration of Zn in these tissues was increased. The changes in the concentration were found to be correlated with the tumour malignancy grade. The efficacy of micro X-ray fluorescence spectroscopy to distinguish between various types of cancer based on the concentrations of studied elements was confirmed by multivariate discriminant analysis. Our analysis showed that the most important elements for tissue classification are Cu, K, Fe, Ca, and Zn. This method made it possible to correctly classify histopathological types in 99.93% of the cases used to build the model and in as much as 99.16% of new cases.
Cashen, M. T.; Koch, P. M.
1997-04-01
In our fast-beam apparatus we have long used( P. Koch and K. van Leeuwen, Phys. Rep. 255), 289 (1995). an electrostatic filter lens (FL) selectively to transmit energy labeled signal ions (e.g., H^+ or He^+) whose energy EB + EL is E_L=40--300 eV above the energy, typically E_B=14.6 keV, of the much more intense primary ion beam. Based on one originally used( H. Zeman, K. Jost, and S. Gilad, Rev. Sci. Inst. 42), 485 (1971). with hundred-eV-energy-range electrons, our 12.8 cm long FL has 21 identical, equally spaced, 0.1 cm thick mumetal disks (11.4 cm OD with 1.91 cm dia. axial hole) electrically biased via resistors so that its near-axis electrostatic field is approximately hyperbolic. We have long noted that the analysis presented in Ref. [3], which ignores focusing effects, fails to explain why our FL has a final cutoff up to five or more times sharper than `theory'. We present ray tracing results obtained with the computer program uc(Simion) to show that strong focusing and higher operating regions (initially parallel rays crossing the axis more than once) play a very important role in the operation of the FL near cutoff and in sharpening its cutoff. Agreement is good.
Tracing X-ray Binary Population Evolution By Galaxy Dissection: First Results from M51
Lehmer, Bret; Eufrasio, Rafael T.; Markwardt, Larissa; Zezas, Andreas; Basu-Zych, Antara; Fragos, Tassos; Hornschemeier, Ann E.; Kalogera, Vassiliki; Ptak, Andrew; Tzanavaris, Panayiotis; Yukita, Mihoko
2017-01-01
Recently, we have found, in the Chandra Deep Field-South, that the emission from X-ray binary (XRB) populations in galaxies evolves significantly with cosmic time, most likely due to changes in the physical properties of galaxies like star-formation rate, stellar mass, stellar age, and metallicity. However, it has been challenging to directly show that these same physical properties are connected to XRB populations using data from nearby galaxies. We present a new technique for empirically calibrating how X-ray binary (XRB) populations evolve following their formation in a variety of environments. We first utilize detailed stellar population synthesis modeling of far-UV to far-IR broadband data of nearby (face-on spiral galaxies to construct maps of the star-formation histories on subgalactic scales. Using Chandra data, we then identify the locations of the XRBs within these galaxies and correlate their formation frequencies with local galaxy properties. In this talk, I will show promising first results for the Whirlpool galaxy (M51), and will discuss how expanding our sample to an archival sample of 20 face-on spirals will lead to a detailed empirical timeline for how XRBs form and evolve in various environments.
Trace the polymerization induced by gamma-ray irradiated silica particles
Lee, Hoik; Ryu, Jungju; Kim, Myungwoong; Im, Seung Soon; Kim, Ick Soo; Sohn, Daewon
2016-08-01
A γ-ray irradiation to inorganic particles is a promising technique for preparation of organic/inorganic composites as it offers a number of advantages such as an additive-free polymerizations conducted under mild conditions, avoiding undesired damage to organic components in the composites. Herein, we demonstrated a step-wise formation mechanism of organic/inorganic nanocomposite hydrogel in detail. The γ-ray irradiation to silica particles dispersed in water generates peroxide groups on their surface, enabling surface-initiated polymerization of acrylic acid from the inorganic material. As a result, poly(acrylic acid) (PAA) covers the silica particles in the form of a core-shell at the initial stage. Then, PAA-coated silica particles associate with each other by combination of radicals at the end of chains on different particles, leading to micro-gel domains. Finally, the micro-gels are further associated with each other to form a 3D network structure. We investigated this mechanism using dynamic light scattering (DLS) and transmission electron microscopy (TEM). Our result strongly suggests that controlling reaction time is critical to achieve specific and desirable organic/inorganic nanocomposite structure among core-shell particles, micro-gels and 3D network bulk hydrogel.
Ménez, Bénédicte; Philippot, Pascal; Bonnin-Mosbah, Michelle; Simionovici, Alexandre; Gibert, François
2002-02-01
A critical problem for conducting quantitative analysis of individual fluid inclusions using Synchrotron X-Ray Fluorescence (SXRF) technique relates to the standardization and the calibration of the X-ray spectra. In this study, different approaches have been tested for calibration purposes: (a) the use of chlorine when Cl content can be estimated either from melting point depressions of undersaturated fluid inclusions or from saturation limits for halite-bearing fluid inclusions, (b) the use of calcium from synthetic fluid inclusions of known CaCl 2 content as an external standard. SXRF analysis was performed on individual fluid inclusions from the Chivor and Guali emerald deposits, Columbia. These well-known samples contain a single fluid inclusion population for which detailed crush-leach analyses are available, thus providing a relevant compositional reference frame. Concentration estimates were also compared to Particle Induced X-ray Emission (PIXE) analysis carried out independently on the same fluid inclusions. Results of the calibration tests indicate that major (Cl, K, Ca, Fe, Mn) and trace element (Cu, Zn, As, Br, Rb, Sr, Ba, Pb) concentration estimates can be performed without precise knowledge of the analytical volume and the inclusion's 3D geometry. Although the standard deviation of the SXRF results can be relatively high depending on the calibration mode used, mean concentration estimates for most elements are in good agreement with PIXE and crush-leach analysis. Elemental distributions within single fluid inclusions were also established. Associated correlation diagrams argue for the homogeneous distribution of most elements in the fluid inclusion. In contrast, Br shows a bimodal distribution interpreted to reflect a significant enrichment of the vapor portion of the inclusion fluid.
Farace, Paolo; Righetto, Roberto; Deffet, Sylvain; Meijers, Arturs; Vander Stappen, Francois
2016-01-01
Purpose: To introduce a fast ray-tracing algorithm in pencil proton radiography (PR) with a multilayer ionization chamber (MLIC) for in vivo range error mapping. Methods: Pencil beam PR was obtained by delivering spots uniformly positioned in a square (45x45 mm(2) field-of-view) of 9x9 spots capable
Determination of trace element levels in leaves of Nerium oleander using X-Ray Fluorescence
Santos, Ramon S.; Sanches, Francis A.C.R.A.; Neves, Arthur O.P.; Oliveira, Luis F.; Oliveira, Davi F.; Anjos, Marcelino J. [Universidade do Estado do Rio de Janeiro (UERJ), Rio de Janeiro, RJ (Brazil). Inst. de Fisica Armando Dias Tavares. Dept. de Fisica Aplicada e Termodinamica
2013-07-01
The environmental pollution by human activity has been one of the most concerns in the last years, principally due to rapid urban growth in the cities and the industrialization process. The air pollution can be increased due to several different kinds of emissions: urban traffic, industrial activities, burning fuel, civil industry of construction/demolition, fires and natural phenomena. Many of these emissions move from long distances due to convections currents and finally tend to deposit mainly in the plants leaves and in the soil. Thus, the plants leaves works as a natural sampler by the emissions deposit in these ones. In this study Nerium oleander leaves were used to measure the environmental pollutions levels in different sampling urban regions in the city of Rio de Janeiro/RJ: Andarai, Benfica, Bonsucesso, Caju, Engenho de Dentro, Engenho Novo, Estacio, Grajau, Inhauma, Lins, Maracana, Maria da Graca, Meier, Praca da Bandeira, Riachuelo, Rio Comprido, Sao Cristovao, Tijuca, Vila Isabel and city Center. The control samples were collected in Campo Grande near of Parque Nacional da Pedra Branca/RJ (National Park of Pedra Branca/RJ). The leaves were collected from adult plants and after the collection the samples were cleaned and placed in the greenhouse for drying, then were mashed and pressed into tablets forms. The analyses were performed using the energy dispersion X-ray fluorescence (EDXRF), developed on the own laboratory and based in a SiPIN detector and a mini X ray tube. It was possible to detect 16 elements in the analyzed samples: K, Ca, Cr, Mn, Fe, Cu, Zn, Br, Rb, Sr, Ba and Pb. The results shows that, in the studied areas, the analysis of the Nerium oleander plant shows a low-cost option and with a substantial efficiency as an environmental pollution biomonitor. (author)
Takahara, Hikari, E-mail: hikari@rigaku.co.jp [Rigaku Corp., 14-8 Akaoji-cho, Takatsuki, Osaka 569-1146 (Japan); Mori, Yoshihiro [Horiba Ltd., 2 Miyanohigashi, Kisshoin, Minami-ku, Kyoto 601-8510 (Japan); Shibata, Harumi [SUMCO Corporation, Seavance North, 1-2-1 Shibaura, Minato-ku, Tokyo 105-8634 (Japan); Shimazaki, Ayako [Toshiba Corporation, 8, Shinsugita-cho, Isogo-ku, Yokohama 235-8522 (Japan); Shabani, Mohammad B. [Mitsubishi Material Corporation, 1-297, Kitabukuro-cho, Omiya-ku, Saitama 330-8508 (Japan); Yamagami, Motoyuki [Rigaku Corp., 14-8 Akaoji-cho, Takatsuki, Osaka 569-1146 (Japan); Yabumoto, Norikuni [Analysis Atelier Co., 4-36-4, Yoyogi, Shibuya-ku, Tokyo 151-0053 (Japan); Nishihagi, Kazuo [Horiba Ltd., 2 Miyanohigashi, Kisshoin, Minami-ku, Kyoto 601-8510 (Japan); Gohshi, Yohichi [Tsukuba University, 1-1-1, Tennodai, Tsukuba, Ibaraki 305-8571 (Japan)
2013-12-01
Vapor phase treatment (VPT) was under investigation by the International Organization for Standardization/Technical Committee 201/Working Group 2 (ISO/TC201/WG2) to improve the detection limit of total reflection X-ray fluorescence spectroscopy (TXRF) for trace metal analysis of silicon wafers. Round robin test results have confirmed that TXRF intensity increased by VPT for intentional contamination with 5 × 10{sup 9} and 5 × 10{sup 10} atoms/cm{sup 2} Fe and Ni. The magnification of intensity enhancement varied greatly (1.2–4.7 in VPT factor) among the participating laboratories, though reproducible results could be obtained for average of mapping measurement. SEM observation results showed that various features, sizes, and surface densities of particles formed on the wafer after VPT. The particle morphology seems to have some impact on the VPT efficiency. High resolution SEM observation revealed that a certain number of dots with SiO{sub 2}, silicate and/or carbon gathered to form a particle and heavy metals, Ni and Fe in this study were segregated on it. The amount and shape of the residue should be important to control VPT factor. - Highlights: • This paper presents a summary of study results of VPT–TXRF using ISO/TC201/WG2. • Our goal is to analyze the trace metallic contamination on silicon wafer with concentrations below 1 × 10{sup 10} atoms/cm{sup 2}. • The efficiency and mechanism of VPT are discussed under several round robin tests and systematic studies.
Greenwald, R. A.; Frissell, N. A.; de Larquier, S.
2016-12-01
In this paper, we evaluate the performance of three methods used by HF radars in the SuperDARN network for determining the ground ranges to ionospheric scattering volumes. Each method uses somewhat different approaches, but the same equivalent-path analysis. We also show that Snell's Law can be added to this analysis to determine the refractive index of each scattering volume and thereby correct Doppler velocity measurements for ionospheric refraction. Two of these methods make their predictions using the group range to the scattering volume and a virtual height model, while the third method uses the group range and the elevation angle each backscattered return. The effectiveness of each of these methods is evaluated using ray tracing analyses through the International Reference Ionosphere. Ray tracings analysis provides determinations of the initial elevation angle, group range, group range, and refractive index of each ionospheric volume that backscatters signals to the radar. The initial or final elevation angle and the group range are used as inputs to the geolocation methods and the ground range and refractive index serve as reference data against which the predictions of the geolocation methods can be evaluated. We find that the methods using virtual height models actually change the initial elevation angle determined from ray tracing to a different elevation angle that is consistent with the virtual height model. Due to this change, predictions of the ground range and refractive index of scattering volumes located with virtual-height models are rarely consistent with the predictions obtained from ray tracing. In contrast, the geolocation method that uses the group range and initial or final elevation angle yields predictions that are in good agreement with ray tracing. Modifications to the equivalent-path analysis are required to obtain consistent predictions of the ground range and refractive index of backscatter from the topside F-layer.
Arindam Pal
2007-01-01
Full Text Available This paper presents an evaluation of the MIMO performance of three candidate antenna array designs, each embedded within a PDA footprint, using indoor wideband channel measurements at 5.2 GHz alongside channel simulations. A channel model which employs the plane-wave approximation was used to combine the embedded antenna radiation patterns of the candidate devices obtained from far-field pattern measurements and multipath component parameters from an indoor ray-tracer. The 4-element candidate arrays were each constructed using a different type of antenna element, and despite the diverse element directivities, pattern characteristics, and polarization purities, all three devices were constructed to fully exploit diversity in polarization, space, and angle. Thus, low correlation and high information theoretic capacity was observed in each case. A good match between the model and the measurements is also demonstrated, especially for 2ÃƒÂ—2 MIMO subsets of identically or orthogonally polarized linear slot antennas. The interdependencies between the channel XPD, directional spread and pathloss, and the respective impact on channel capacity are also discussed in this paper.
Pal Arindam
2007-01-01
Full Text Available This paper presents an evaluation of the MIMO performance of three candidate antenna array designs, each embedded within a PDA footprint, using indoor wideband channel measurements at 5.2 GHz alongside channel simulations. A channel model which employs the plane-wave approximation was used to combine the embedded antenna radiation patterns of the candidate devices obtained from far-field pattern measurements and multipath component parameters from an indoor ray-tracer. The 4-element candidate arrays were each constructed using a different type of antenna element, and despite the diverse element directivities, pattern characteristics, and polarization purities, all three devices were constructed to fully exploit diversity in polarization, space, and angle. Thus, low correlation and high information theoretic capacity was observed in each case. A good match between the model and the measurements is also demonstrated, especially for MIMO subsets of identically or orthogonally polarized linear slot antennas. The interdependencies between the channel XPD, directional spread and pathloss, and the respective impact on channel capacity are also discussed in this paper.
Silva Marina P
2012-07-01
Full Text Available Abstract Background The application and better understanding of traditional and new breast tumor biomarkers and prognostic factors are increasing due to the fact that they are able to identify individuals at high risk of breast cancer, who may benefit from preventive interventions. Also, biomarkers can make possible for physicians to design an individualized treatment for each patient. Previous studies showed that trace elements (TEs determined by X-Ray Fluorescence (XRF techniques are found in significantly higher concentrations in neoplastic breast tissues (malignant and benign when compared with normal tissues. The aim of this work was to evaluate the potential of TEs, determined by the use of the Energy Dispersive X-Ray Fluorescence (EDXRF technique, as biomarkers and prognostic factors in breast cancer. Methods By using EDXRF, we determined Ca, Fe, Cu, and Zn trace elements concentrations in 106 samples of normal and breast cancer tissues. Cut-off values for each TE were determined through Receiver Operating Characteristic (ROC analysis from the TEs distributions. These values were used to set the positive or negative expression. This expression was subsequently correlated with clinical prognostic factors through Fisher’s exact test and chi-square test. Kaplan Meier survival curves were also evaluated to assess the effect of the expression of TEs in the overall patient survival. Results Concentrations of TEs are higher in neoplastic tissues (malignant and benign when compared with normal tissues. Results from ROC analysis showed that TEs can be considered a tumor biomarker because, after establishing a cut-off value, it was possible to classify different tissues as normal or neoplastic, as well as different types of cancer. The expression of TEs was found statistically correlated with age and menstrual status. The survival curves estimated by the Kaplan-Meier method showed that patients with positive expression for Cu presented a poor
Jie Ji
2012-09-01
Full Text Available This study aims to determine the necessity of applying a mirror coating on the side of a truncated solid dielectric CPC (compound parabolic concentrator since ray tracing analysis has revealed that part of the incoming rays do not undergo total internal reflection, even within the half acceptance angle of the CPC. An experiment was designed and conducted indoors and outdoors to study the effect of mirror coating on the optical performance of a solid dielectric CPC. Ray tracing was also employed for the detailed analysis and its results are compared with the measurements. Based on these, a concept of partial coating is proposed and verified through simulation. The results show that a partly coated solid dielectric CPC may have a better optical efficiency than a solid CPC without coating for a certain range of incidence angles.
Complexity in Managing Modularization
Hansen, Poul H. Kyvsgård; Sun, Hongyi
2011-01-01
In general, the phenomenon of managing modularization is not well known. The cause-effect relationships between modularization and realized benefits are complex and comprehensive. Though a number of research works have contributed to the study of the phenomenon of efficient and effective modulari......In general, the phenomenon of managing modularization is not well known. The cause-effect relationships between modularization and realized benefits are complex and comprehensive. Though a number of research works have contributed to the study of the phenomenon of efficient and effective...... modularization management it is far from clarified. Recognizing the need for further empirical research, we have studied 40 modularity cases in various companies. The studies have been designed as long-term studies leaving time for various types of modularization benefits to emerge. Based on these studies we...... have developed a framework to support the heuristic and iterative process of planning and realizing modularization benefits....
Modularity and Economic Organization
Sanchez, Ron; Mahoney, Joseph T.
This paper addresses modularity as a basis for organizing economic activity. We first define the key concepts of architecture and of modularity as a special form of architecture. We then suggest how modular systems of all types may exhibit several properties of fundamental importance...... to the organization of economic activities, including greater adaptability and evolvability than systems that lack modular properties. We draw extensively on our original 1996 paper on modularity and subsequent research to suggest broad theoretical implications of modularity for (i) firms' product strategies...... and the nature of product market competition, (ii) the organization designs firms may adopt and the industry structures that can result when significant numbers of firms adopt modular product architectures, and (iii) learning processes and knowledge structures at the firm and industry levels in modular product...
Understanding Socio Technical Modularity
Thuesen, Christian Langhoff; Kudsk, Anders; Hvam, Lars
2011-01-01
Modularity has gained an increasing popularity as a central concept for exploring product structure, process structure, organization structure and supply chain structure. With the offset in system theory the predominant understanding of modularity however faces difficulties in explaining the social...... dimension of modularity like irrational behaviors, cultural differences, learning processes, social organization and institutional influences on modularity. The paper addresses this gab offering a reinterpretation of the modularity concept from a socio-technical perspective in general and Actor Network...... Theory in particular. By formulating modularity from an ANT perspective covering social, material and process aspects, the modularity of a socio-technical system can be understood as an entanglement of product, process, organizational and institutional modularity. The theoretical framework is illustrated...
Wang, Xiao-Huan; Meng, Qing-Fen; Dong, Ya-Ping; Chen, Mei-Da; Li, Wu
2010-03-01
A rapid multi-element analysis method for clay mineral samples was described. This method utilized a polarized wave-length dispersive X-ray fluorescence spectrometer--Axios PW4400, which had a maximum tube power of 4 000 watts. The method was developed for the determination of As, Mn, Co, Cu, Cr, Dy, Ga, Mo, P, Pb, Rb, S, Sr, Ni, ,Cs, Ta, Th, Ti, U, V, Y, Zn, Zr, MgO, K2O, Na2O, CaO, Fe2O3, Al2O3, SiO2 and so on. Thirty elements in clay mineral species were measured by X-ray fluorescence spectrometry with pressed powder pellets. Spectral interferences, in particular the indirect interferences of each element, were studied. A method to distinguish the interference between each other periodic elements in element periodic table was put forward. The measuring conditions and existence were mainly investigated, and the selected background position as well as corrected spectral overlap for the trace elements were also discussed. It was found that the indirect spectral overlap line was the same important as direct spectral overlap line. Due to inducing the effect of indirect spectral overlap, some elements jlike Bi, Sn, W which do not need analysis were also added to the elements channel. The relative standard deviation (RSD) was in the range of 0.01% to 5.45% except three elements Mo, Cs and Ta. The detection limits, precisions and accuracies for most elements using this method can meet the requirements of sample analysis in clay mineral species.
Comparison of VTEC from ground-based space geodetic techniques based on ray-traced mapping factors
Heinkelmann, Robert; Alizadeh, M. Mahdi; Schuh, Harald; Deng, Zhiguo; Zus, Florian; Etemadfard, M. Hossein
2016-07-01
For the derivation of vertical total electron content (VTEC) from slant total electron content (STEC), usually a standard approach is used based on mapping functions that assume a single-layer model of the ionosphere (e.g. IERS Conventions 2010). In our study we test the standard approach against a recently developed alternative which is based on station specific ray-traced mapping factors. For the evaluation of this new mapping concept, we compute VTEC at selected Very Long Baseline Interferometry (VLBI) stations using the dispersive delays and the corresponding formal errors obtained by observing extra-galactic radio sources at two radio frequencies in S- and X-bands by the permanent geodetic/astrometric program organized by the IVS (International VLBI Service for Geodesy and Astrometry). Additionally, by applying synchronous sampling and a consistent analysis configuration, we determine VTEC at Global Navigation Satellite System (GNSS) antennas using GPS (Global Positioning System) and/or GLONASS (Globalnaja nawigazionnaja sputnikowaja Sistema) observations provided by the IGS (International GNSS Service) that are operated in the vicinity of the VLBI antennas. We compare the VTEC time series obtained by the individual techniques over a period of about twenty years and describe their characteristics qualitatively and statistically. The length of the time series allows us to assess the long-term climatology of ionospheric VTEC during the last twenty years.
Fu, Lei
2017-05-11
Full-waveform inversion of land seismic data tends to get stuck in a local minimum associated with the waveform misfit function. This problem can be partly mitigated by using an initial velocity model that is close to the true velocity model. This initial starting model can be obtained by inverting traveltimes with ray-tracing traveltime tomography (RT) or wave-equation traveltime (WT) inversion. We have found that WT can provide a more accurate tomogram than RT by inverting the first-arrival traveltimes, and empirical tests suggest that RT is more sensitive to the additive noise in the input data than WT. We present two examples of applying WT and RT to land seismic data acquired in western Saudi Arabia. One of the seismic experiments investigated the water-table depth, and the other one attempted to detect the location of a buried fault. The seismic land data were inverted by WT and RT to generate the P-velocity tomograms, from which we can clearly identify the water table depth along the seismic survey line in the first example and the fault location in the second example.
Custodio, P.J.; Carvalho, M.L. [Centro Fisica Atomica, Universidade de Lisboa, Av. Prof. Gama Pinto, 2, 1649-003, Lisboa (Portugal); Nunes, F. [Hospital Garcia de Orta, Almada (Portugal)
2003-04-01
This work is an application of energy dispersive X-ray fluorescence (EDXRF) as an analytical technique for trace elemental determination in human membrane and placenta and elemental concentrations correlations in both tissues. Whole samples were collected during the delivery from healthy mothers and full-term pregnancies. The age of the mother was between 25 and 40 years old, and the weight of the infants ranged from 2.56 to 4.05 kg. Samples were lyophilised and analysed without any chemical treatment. No significant differences in elemental content of placenta and membrane samples were observed except for Ca. Very low levels of Se, As and Pb were observed in all the analysed samples. Zn, considered as one of the key elements in newborn health, was not significantly different in the analysed samples, all of which originated from healthy mothers and healthy babies. The obtained values agree with the literature except for Ca, which is much higher in the studied samples. (orig.)
Connolly, G D; Lowe, M J S; Temple, J A G; Rokhlin, S I
2010-05-01
The use of ultrasonic arrays has increased dramatically within recent years due to their ability to perform multiple types of inspection and to produce images of the structure through post-processing of received signals. Phased arrays offer many advantages over conventional transducers in the inspection of materials that are inhomogeneous with spatially varying anisotropic properties. In this paper, the arrays are focused on austenitic steel welds as a representative inhomogeneous material. The method of ray-tracing through a previously developed model of an inhomogeneous weld is shown, with particular emphasis on the difficulties presented by material inhomogeneity. The delay laws for the structure are computed and are used to perform synthetic focusing at the post-processing stage of signal data acquired by the array. It is demonstrated for a simulated austenitic weld that by taking material inhomogeneity and anisotropy into account, superior reflector location (and hence, superior sizing) results when compared to cases where these are ignored. The image is thus said to have been corrected. Typical images are produced from both analytical data in the frequency domain and data from finite element simulations in the time domain in a variety of wave modes, including cases with mode conversion and reflections.
Stevens, John [Univ. of California, Berkeley, CA (United States)
2013-12-01
Ray tracing was used to perform optical optimization of arrays of photovoltaic microrods and explore the interaction between light and bubbles of oxygen gas on the surface of the microrods. The incident angle of light was varied over a wide range. The percent of incident light absorbed by the microrods and reflected by the bubbles was computed over this range. It was found that, for the 10 μm diameter, 100 μm tall SrTiO_{3} microrods simulated in the model, the optimal center-to-center spacing was 14 μm for a square grid. This geometry produced 75% average and 90% maximum absorbance. For a triangular grid using the same microrods, the optimal center-to-center spacing was 14 μm. This geometry produced 67% average and 85% maximum absorbance. For a randomly laid out grid of 5 μm diameter, 100 μm tall SrTiO! microrods with an average center-to-center spacing of 20 μm, the average absorption was 23% and the maximum absorption was 43%. For a 50% areal coverage fraction of bubbles on the absorber surface, between 2%-20% of the incident light energy was reflected away from the rods by the bubbles, depending upon incident angle and bubble morphology.
Pelzers, R S; Yu, Q L; Mangkuto, R A
2014-10-01
This article aims to understand the radiation behavior within a photo-reactor, following the ISO 22197-1:2007 standard. The RADIANCE lighting simulation tool, based on the backward ray-tracing modeling method, is employed for a numerical computation of the radiation field. The reflection of the glass cover in the photo-reactor and the test sample influence the amount of irradiance received by the test-sample surface in the photo-reactor setup. The reflection of a white sample limits the irradiance reduction by the glass cover to 1.4 %, but darker samples can lead to an overestimation up to 9.8 % when used in the same setup. This overestimation could introduce considerable error into the interpretation of experiments. Furthermore, this method demonstrates that the kinetics for indoor photocatalytic pollutant degradation can be refined through radiation modeling of the reactor setup. In addition, RADIANCE may aid in future modeling of the more complex indoor environment where radiation affects significantly photocatalytic activity.
Sassen, Kenneth; Knight, Nancy C.; Takano, Yoshihide; Heymsfield, Andrew J.
1994-01-01
During the 1986 Project FIRE (First International Satellite Cloud Climatology Project Regional Experiment) field campaign, four 22 deg halo-producing cirrus clouds were studied jointly from a ground-based polarization lidar and an instrumented aircraft. The lidar data show the vertical cloud structure and the relative position of the aircraft, which collected a total of 84 slides by impaction, preserving the ice crystals for later microscopic examination. Although many particles were too fragile to survive impaction intact, a large fraction of the identifiable crystals were columns and radial bullet rosettes, with both displaying internal cavitations and radial plate-column combinations. Particles that were solid or displayed only a slight amount of internal structure were relatively rare, which shows that the usual model postulated by halo theorists, i.e., the randomly oriented, solid hexagonal crystal, is inappropriate for typical cirrus clouds. With the aid of new ray-tracing simulations for hexagonal hollow-ended column and bullet-rosette models, we evaluate the effects of more realistic ice-crystal structures on halo formation and lidar depolarization and consider why the common halo is not more common in cirrus clouds.
Jensen, K. A.; Ripoll, J.-F.; Wray, A. A.; Joseph, D.; ElHafi, M.
2004-01-01
Five computational methods for solution of the radiative transfer equation in an absorbing-emitting and non-scattering gray medium were compared on a 2 m JP-8 pool fire. The temperature and absorption coefficient fields were taken from a synthetic fire due to the lack of a complete set of experimental data for fires of this size. These quantities were generated by a code that has been shown to agree well with the limited quantity of relevant data in the literature. Reference solutions to the governing equation were determined using the Monte Carlo method and a ray tracing scheme with high angular resolution. Solutions using the discrete transfer method, the discrete ordinate method (DOM) with both S(sub 4) and LC(sub 11) quadratures, and moment model using the M(sub 1) closure were compared to the reference solutions in both isotropic and anisotropic regions of the computational domain. DOM LC(sub 11) is shown to be the more accurate than the commonly used S(sub 4) quadrature technique, especially in anisotropic regions of the fire domain. This represents the first study where the M(sub 1) method was applied to a combustion problem occurring in a complex three-dimensional geometry. The M(sub 1) results agree well with other solution techniques, which is encouraging for future applications to similar problems since it is computationally the least expensive solution technique. Moreover, M(sub 1) results are comparable to DOM S(sub 4).
Ray-trace simulation of CuInS(Se)₂ quantum dot based luminescent solar concentrators.
Hu, Xiangmin; Kang, Ruidan; Zhang, Yongyou; Deng, Luogen; Zhong, Haizheng; Zou, Bingsuo; Shi, Li-Jie
2015-07-27
To enhance the performance of luminescent solar concentrator (LSC), there is an increased need to search novel emissive materials with broad absorption and large Stokes shifts. I-III-VI colloidal CuInS2 and CuInSe2 based nanocrystals, which exhibit strong photoluminescence emissions in the visible to near infrared region with large Stokes shifts, are expected to improve performance in luminescent solar concentrator applications. In this work, the performance of CuInS(Se)2 quantum dots in simple planar LSC is evaluated by applying Monte-Carlo ray-trace simulation. A systematic parameters study was conducted to optimize the performance. An optimized photon concentration ratio of 0.34 for CuInS2 nanocrystals and 1.25 for CuInSe2 nanocrystals doping LSC are obtained from the simulation. The results demonstrated that CuInSe2 based nanocrystals are particularly interesting for luminescent solar concentrator applications, especially to combine with low price Si solar cells.
Decomposition theorems for Hilbert modular newforms
Linowitz, Benjamin
2011-01-01
Let $\\mathscr{S}_k^+(\\cn,\\Phi)$ denote the space generated by Hilbert modular newforms (over a fixed totally real field $K$) of weight $k$, level $\\cn$ and Hecke character $\\Phi$. We show how to decompose $\\mathscr{S}_k^+(\\cn,\\Phi)$ into direct sums of twists of other spaces of newforms. This sheds light on the behavior of a newform under a character twist: the exact level of the twist of a newform, when such a twist is itself a newform, and when a newform may be realized as the twist of a primitive newform. These results were proven for elliptic modular forms by Hijikata, Pizer and Shemanske by employing a formula for the trace of the Hecke operator $T_k(n)$. We obtain our results not by employing a more general formula for the trace of Hecke operators on spaces of Hilbert modular forms, but instead by using basic properties of newforms which were proven for elliptic modular forms by Li, and Atkin and Li, and later extended to Hilbert modular forms by Shemanske and Walling.
Complexity in Managing Modularization
Hansen, Poul H. Kyvsgård; Sun, Hongyi
2011-01-01
modularization management it is far from clarified. Recognizing the need for further empirical research, we have studied 40 modularity cases in various companies. The studies have been designed as long-term studies leaving time for various types of modularization benefits to emerge. Based on these studies we......In general, the phenomenon of managing modularization is not well known. The cause-effect relationships between modularization and realized benefits are complex and comprehensive. Though a number of research works have contributed to the study of the phenomenon of efficient and effective...
Kolkoori, Sanjeevareddy
2014-07-01
Austenitic welds and dissimilar welds are extensively used in primary circuit pipes and pressure vessels in nuclear power plants, chemical industries and fossil fuelled power plants because of their high fracture toughness, resistance to corrosion and creep at elevated temperatures. However, cracks may initiate in these weld materials during fabrication process or stress operations in service. Thus, it is very important to evaluate the structural integrity of these materials using highly reliable non-destructive testing (NDT) methods. Ultrasonic non-destructive inspection of austenitic welds and dissimilar weld components is complicated because of anisotropic columnar grain structure leading to beam splitting and beam deflection. Simulation tools play an important role in developing advanced reliable ultrasonic testing (UT) techniques and optimizing experimental parameters for inspection of austenitic welds and dissimilar weld components. The main aim of the thesis is to develop a 3D ray tracing model for quantitative evaluation of ultrasonic wave propagation in an inhomogeneous anisotropic austenitic weld material. Inhomogenity in the anisotropic weld material is represented by discretizing into several homogeneous layers. According to ray tracing model, ultrasonic ray paths are traced during its energy propagation through various discretized layers of the material and at each interface the problem of reflection and transmission is solved. The influence of anisotropy on ultrasonic reflection and transmission behaviour in an anisotropic austenitic weld material are quantitatively analyzed in three dimensions. The ultrasonic beam directivity in columnar grained austenitic steel material is determined three dimensionally using Lamb's reciprocity theorem. The developed ray tracing model evaluates the transducer excited ultrasonic fields accurately by taking into account the directivity of the transducer, divergence of the ray bundle, density of rays and phase
Modularity and Economic Organization
Sanchez, Ron; Mahoney, Joseph T.
and the nature of product market competition, (ii) the organization designs firms may adopt and the industry structures that can result when significant numbers of firms adopt modular product architectures, and (iii) learning processes and knowledge structures at the firm and industry levels in modular product...... markets. We also discuss an evolutionary perspective on modularity as an emergent phenomenon in firms and industries. We explain how modularity as a relatively new field of strategy and economic research may provide a new theoretical perspective on economic organizing that has significant potential......This paper addresses modularity as a basis for organizing economic activity. We first define the key concepts of architecture and of modularity as a special form of architecture. We then suggest how modular systems of all types may exhibit several properties of fundamental importance...
Product Architecture Modularity Strategies
Mikkola, Juliana Hsuan
2003-01-01
The focus of this paper is to integrate various perspectives on product architecture modularity into a general framework, and also to propose a way to measure the degree of modularization embedded in product architectures. Various trade-offs between modular and integral product architectures...... and how components and interfaces influence the degree of modularization are considered. In order to gain a better understanding of product architecture modularity as a strategy, a theoretical framework and propositions are drawn from various academic literature sources. Based on the literature review......, the following key elements of product architecture are identified: components (standard and new-to-the-firm), interfaces (standardization and specification), degree of coupling, and substitutability. A mathematical function, termed modularization function, is introduced to measure the degree of modularization...
Dorn, Ulrich; Neumann, Daniel; Frank, Mario
2014-04-01
This study compared the corrosion behavior of tantalum-coated cobalt-chromium modular necks with that of titanium alloy modular necks at their junction to titanium-alloy femoral stem. Tests were performed in a dry assembly and two wet assemblies, one contaminated with calf serum and the other contaminated with calf serum and bone particles. Whereas the titanium modular neck tested in the dry assembly showed no signs of corrosion, the titanium modular necks tested in both wet assemblies showed marked depositions and corrosive attacks. By contrast, the tantalum-coated cobalt-chromium modular necks showed no traces of corrosion or chemical attack in any of the three assemblies. This study confirms the protective effect of tantalum coating the taper region of cobalt-chromium modular neck components, suggesting that the use of tantalum may reduce the risk of implant failure due to corrosion.
On modular semifinite index theory
Kaad, Jens
2011-01-01
We propose a definition of a modular spectral triple which covers existing examples arising from KMS-states, Podles sphere and quantum SU(2). The definition also incorporates the notion of twisted commutators appearing in recent work of Connes and Moscovici. We show how a finitely summable modular spectral triple admits a twisted index pairing with unitaries satisfying a modular condition. The twist means that the dimensions of kernels and cokernels are measured with respect to two different but intimately related traces. The twisted index pairing can be expressed by pairing Chern characters in reduced versions of twisted cyclic theories. We end the paper by giving a local formula for the reduced Chern character in the case of quantum SU(2). It appears as a twisted coboundary of the Haar-state. In particular we present an explicit computation of the twisted index pairing arising from the sequence of corepresentation unitaries. As an important tool we construct a family of derived integration spaces associated...
Niccolini, Gilles; De Souza, Armando Domiciano
2010-01-01
The physical interpretation of spectro-interferometric data is strongly model-dependent. On one hand, models involving elaborate radiative transfer solvers are too time consuming in general to perform an automatic fitting procedure and derive astrophysical quantities and their related errors. On the other hand, using simple geometrical models does not give sufficient insights into the physics of the object. We propose to stand in between these two extreme approaches by using a physical but still simple parameterised model for the object under consideration. Based on this philosophy, we developed a numerical tool optimised for mid-infrared (mid-IR) interferometry, the fast ray-tracing algorithm for circumstellar structures (FRACS) which can be used as a stand-alone model, or as an aid for a more advanced physical description or even for elaborating observation strategies. FRACS is based on the ray-tracing technique without scattering, but supplemented with the use of quadtree meshes and the full symmetries of ...
Baba, Y.; Shimoyama, I.; Hirao, N.
2016-10-01
In order to determine the chemical states of radioactive cesium (137Cs or 134Cs) sorbed in clay minerals, chemical states of cesium as well as the other alkali metals (sodium and rubidium) sorbed in micaceous oxides have been investigated by X-ray photoelectron spectroscopy (XPS). Since the number of atoms in radioactive cesium is extremely small, we specially focused on chemical states of trace-level alkali metals. For this purpose, we have measured XPS under X-ray total reflection (TR) condition. For cesium, it was shown that ultra-trace amount of cesium down to about 100 pg cm-2 can be detected by TR-XPS. This amount corresponds to about 200 Bq of 137Cs (t1/2 = 30.2 y). It was demonstrated that ultra-trace amount of cesium corresponding to radioactive cesium level can be measured by TR-XPS. As to the chemical states, it was found that core-level binding energy in TR-XPS for trace-level cesium shifted to lower-energy side compared with that for thicker layer. A reverse tendency is observed in sodium. Based on charge transfer within a simple point-charge model, it is concluded that chemical bond between alkali metal and micaceous oxide for ultra-thin layer is more polarized that for thick layer.
Yun, W.; Lewis, S.; Stripe, B.; Chen, S.; Reynolds, D.; Spink, I.; Lyon, A.
2015-12-01
We are developing a patent-pending x-ray microprobe with substantially unprecedented performance attributes: working distances of >2 cm, narrow spectral bandwidth, and large x-ray flux. The outstanding performance is enabled by: (1) a revolutionary new type of high flux x-ray source designed to be >10X brighter than the brightest rotating anode x-ray source available; (2) an axially symmetric x-ray mirror lens with large solid angle collection and high focusing efficiency; and (3) a detector configuration that enables the collection of 10X more x-rays than current microXRF designs. The sensitivity will be ppm-scale, far surpassing charged particle analysis (e.g. EPMA and SEM-EDS), and >1000X throughput over the leading micro-XRFs. Despite the introduction of a number of laboratory microXRF systems in the past decade, the state-of-the-art has been limited primarily by low resolution (~30 μm) and low throughput. This is substantially attributable to a combination of low x-ray source brightness and poor performance x-ray optics. Here we present our initial results in removing the x-ray source bottleneck, in which we use a novel x-ray source using Fine Anode Array Source Technology (Sigray FAAST™). When coupled with our proprietary high efficiency x-ray mirror lens, the throughput achieved is comparable to that of many synchrotron microXRF beamlines. Potential applications of the x-ray microprobe include high throughput mapping of mineralogy at high resolution, including trace elements, such as rare earth metals, and deposits (e.g. siderite, clays), with ppm sensitivity, providing information for properties such as permeability and elastic/mechanical properties, and to provide compositional information for Digital Rock. Additional applications include those in which the limited penetration of electrons limits achieving adequate statistics, such as determining the concentration of precious minerals in mine tailings.
Causin, Valerio; Marega, Carla; Carresi, Pietro; Schiavone, Sergio; Marigo, Antonio
2007-05-03
Thirty-three shopping bags, commonly encountered in the packaging of drug doses, were characterized by wide angle X-ray diffraction (WAXD). Using this single technique, without sample preparation, nearly all the considered samples could be differentiated, achieving a discriminating power of 0.992. The rather large degree of variability existing in grocery bags, even though they are mass produced, was shown, confirming that these items can be useful in tracing the source of illicit drug doses.
M Grafe; M Landers; R Tappero; P Austin; B Gan; A Grabsch; C Klauber
2011-12-31
We describe the application of quantitative evaluation of mineralogy by scanning electron microscopy in combination with techniques commonly available at hard X-ray microprobes to define the mineralogical environment of a bauxite residue core segment with the more specific aim of determining the speciation of trace metals (e.g., Ti, V, Cr, and Mn) within the mineral matrix. Successful trace metal speciation in heterogeneous matrices, such as those encountered in soils or mineral residues, relies on a combination of techniques including spectroscopy, microscopy, diffraction, and wet chemical and physical experiments. Of substantial interest is the ability to define the mineralogy of a sample to infer redox behavior, pH buffering, and mineral-water interfaces that are likely to interact with trace metals through adsorption, coprecipitation, dissolution, or electron transfer reactions. Quantitative evaluation of mineralogy by scanning electron microscopy coupled with micro-focused X-ray diffraction, micro-X-ray fluorescence, and micro-X-ray absorption near edge structure (mXANES) spectroscopy provided detailed insights into the composition of mineral assemblages and their effect on trace metal speciation during this investigation. In the sample investigated, titanium occurs as poorly ordered ilmenite, as rutile, and is substituted in iron oxides. Manganese's spatial correlation to Ti is closely linked to ilmenite, where it appears to substitute for Fe and Ti in the ilmenite structure based on its mXANES signature. Vanadium is associated with ilmenite and goethite but always assumes the +4 oxidation state, whereas chromium is predominantly in the +3 oxidation state and solely associated with iron oxides (goethite and hematite) and appears to substitute for Fe in the goethite structure.
van Aardt, J. A.; van Leeuwen, M.; Kelbe, D.; Kampe, T.; Krause, K.
2015-12-01
Remote sensing is widely accepted as a useful technology for characterizing the Earth surface in an objective, reproducible, and economically feasible manner. To date, the calibration and validation of remote sensing data sets and biophysical parameter estimates remain challenging due to the requirements to sample large areas for ground-truth data collection, and restrictions to sample these data within narrow temporal windows centered around flight campaigns or satellite overpasses. The computer graphics community have taken significant steps to ameliorate some of these challenges by providing an ability to generate synthetic images based on geometrically and optically realistic representations of complex targets and imaging instruments. These synthetic data can be used for conceptual and diagnostic tests of instrumentation prior to sensor deployment or to examine linkages between biophysical characteristics of the Earth surface and at-sensor radiance. In the last two decades, the use of image generation techniques for remote sensing of the vegetated environment has evolved from the simulation of simple homogeneous, hypothetical vegetation canopies, to advanced scenes and renderings with a high degree of photo-realism. Reported virtual scenes comprise up to 100M surface facets; however, due to the tighter coupling between hardware and software development, the full potential of image generation techniques for forestry applications yet remains to be fully explored. In this presentation, we examine the potential computer graphics techniques have for the analysis of forest structure-function relationships and demonstrate techniques that provide for the modeling of extremely high-faceted virtual forest canopies, comprising billions of scene elements. We demonstrate the use of ray tracing simulations for the analysis of gap size distributions and characterization of foliage clumping within spatial footprints that allow for a tight matching between characteristics
Kim, Jee Hoon; Lee, Joon Woo; Ahn, Tae In; Shin, Jong Hwa; Park, Kyung Sub; Son, Jung Eek
2016-01-01
Canopy photosynthesis has typically been estimated using mathematical models that have the following assumptions: the light interception inside the canopy exponentially declines with the canopy depth, and the photosynthetic capacity is affected by light interception as a result of acclimation. However, in actual situations, light interception in the canopy is quite heterogenous depending on environmental factors such as the location, microclimate, leaf area index, and canopy architecture. It is important to apply these factors in an analysis. The objective of the current study is to estimate the canopy photosynthesis of paprika (Capsicum annuum L.) with an analysis of by simulating the intercepted irradiation of the canopy using a 3D ray-tracing and photosynthetic capacity in each layer. By inputting the structural data of an actual plant, the 3D architecture of paprika was reconstructed using graphic software (Houdini FX, FX, Canada). The light curves and A/C i curve of each layer were measured to parameterize the Farquhar, von Caemmerer, and Berry (FvCB) model. The difference in photosynthetic capacity within the canopy was observed. With the intercepted irradiation data and photosynthetic parameters of each layer, the values of an entire plant's photosynthesis rate were estimated by integrating the calculated photosynthesis rate at each layer. The estimated photosynthesis rate of an entire plant showed good agreement with the measured plant using a closed chamber for validation. From the results, this method was considered as a reliable tool to predict canopy photosynthesis using light interception, and can be extended to analyze the canopy photosynthesis in actual greenhouse conditions.
Jee Hoon Kim
2016-09-01
Full Text Available Canopy photosynthesis has typically been estimated using mathematical models that have the following assumptions: the light interception inside the canopy exponentially declines with the canopy depth, and the photosynthetic capacity is affected by light interception as a result of acclimation. However, in actual situations, light interception in the canopy is quite heterogenous depending on environmental factors such as the location, microclimate, leaf area index, and canopy architecture. It is important to apply these factors in an analysis. The objective of the current study is to estimate the canopy photosynthesis of paprika (Capsicum annuum L. with an analysis of by simulating the intercepted irradiation of the canopy using a 3D ray-tracing and photosynthetic capacity in each layer. By inputting the structural data of an actual plant, the 3D architecture of paprika was reconstructed using graphic software (Houdini FX, FX, Canada. The light curves and A/Ci curve of each layer were measured to parameterize the Farquhar, von Caemmerer and Berry (FvCB model. The difference in photosynthetic capacity within the canopy was observed. With the intercepted irradiation data and photosynthetic parameters of each layer, the values of an entire plant’s photosynthesis rate were estimated by integrating the calculated photosynthesis rate at each layer. The estimated photosynthesis rate of an entire plant showed good agreement with the measured plant using a closed chamber for validation. From the results, this method was considered as a reliable tool to predict canopy photosynthesis using light interception, and can be extended to analyze the canopy photosynthesis in actual greenhouse conditions.
Kim, Jee Hoon; Lee, Joon Woo; Ahn, Tae In; Shin, Jong Hwa; Park, Kyung Sub; Son, Jung Eek
2016-01-01
Canopy photosynthesis has typically been estimated using mathematical models that have the following assumptions: the light interception inside the canopy exponentially declines with the canopy depth, and the photosynthetic capacity is affected by light interception as a result of acclimation. However, in actual situations, light interception in the canopy is quite heterogenous depending on environmental factors such as the location, microclimate, leaf area index, and canopy architecture. It is important to apply these factors in an analysis. The objective of the current study is to estimate the canopy photosynthesis of paprika (Capsicum annuum L.) with an analysis of by simulating the intercepted irradiation of the canopy using a 3D ray-tracing and photosynthetic capacity in each layer. By inputting the structural data of an actual plant, the 3D architecture of paprika was reconstructed using graphic software (Houdini FX, FX, Canada). The light curves and A/Ci curve of each layer were measured to parameterize the Farquhar, von Caemmerer, and Berry (FvCB) model. The difference in photosynthetic capacity within the canopy was observed. With the intercepted irradiation data and photosynthetic parameters of each layer, the values of an entire plant's photosynthesis rate were estimated by integrating the calculated photosynthesis rate at each layer. The estimated photosynthesis rate of an entire plant showed good agreement with the measured plant using a closed chamber for validation. From the results, this method was considered as a reliable tool to predict canopy photosynthesis using light interception, and can be extended to analyze the canopy photosynthesis in actual greenhouse conditions. PMID:27667994
Flandes, Alberto; Spilker, Linda; Déau, Estelle
2016-10-01
Saturn's rings are a complex collection of icy particles with diameters from 1 m to few meters. Their natural window of study is the infrared because its temperatures are between 40K and 120K. The main driver of the temperature of these rings is the direct solar radiation as well as the solar radiation reflected off Saturn's atmosphere. The second most important energy source is the infrared radiation coming from Saturn itself. The study of the variations of temperatures of the rings, or, in general, their thermal behavior, may provide important information on their composition, their structure and their dynamics. Models that consider these and other energy sources are able to explain, to a first approximation, the observed temperature variations of the rings. The challenge for these models is to accurately describe the variation of illumination on the rings, i. e., how the illuminated and non-illuminated regions of the ring particles change at the different observation geometries. This shadowing mainly depends on the optical depth, as well as the general structure of the rings.In this work, We show a semi-analytical model that considers the main energy sources of the rings and their average properties (e.g., optical depth, particle size range and vertical distribution). In order to deal with the shadowing at specific geometries, the model uses the ray-tracing technique. The goal is to describe the ring temperatures observed by the Composite Infrared Spectrometer, CIRS, onboard the Cassini spacecraft, which is in orbit around Saturn since 2004. So far, the model is able to reproduce some of the general features of specific regions of the A, B and C rings.
张昕; 刘月巍; 王斌; 季仲贞
2004-01-01
The Spectral Statistical Interpolation (SSI) analysis system of NCEP is used to assimilate meteorological data from the Global Positioning Satellite System (GPS/MET) refraction angles with the variational technique. Verified by radiosonde, including GPS/MET observations into the analysis makes an overall improvement to the analysis variables of temperature, winds, and water vapor. However, the variational model with the ray-tracing method is quite expensive for numerical weather prediction and climate research. For example, about 4 000 GPS/MET refraction angles need to be assimilated to produce an ideal global analysis. Just one iteration of minimization will take more than 24 hours CPU time on the NCEP's Gray C90 computer. Although efforts have been taken to reduce the computational cost, it is still prohibitive for operational data assimilation. In this paper, a parallel version of the three-dimensional variational data assimilation model of GPS/MET occultation measurement suitable for massive parallel processors architectures is developed. The divide-and-conquer strategy is used to achieve parallelism and is implemented by message passing. The authors present the principles for the code's design and examine the performance on the state-of-the-art parallel computers in China. The results show that this parallel model scales favorably as the number of processors is increased. With the Memory-IO technique implemented by the author, the wall clock time per iteration used for assimilating 1420 refraction angles is reduced from 45 s to 12 s using 1420 processors. This suggests that the new parallelized code has the potential to be useful in numerical weather prediction (NWP) and climate studies.
Qiao Liya; Wan Xiuhua; Cai Xiaogu; Balamurali Vasudevan; Xiong Ying; Tan Jiaxuan; Guan Zheng
2014-01-01
Background The evaluation of retinal image quality in cataract eyes has gained importance and the clinical modulation transfer functions (MTF) can obtained by aberrometer and double pass (DP) system.This study aimed to compare MTF derived from a ray tracing aberrometer and a DP system in eady cataractous and normal eyes.Methods There were 128 subjects with 61 control eyes and 67 eyes with early cataract defined according to the Lens Opacities Classification System Ⅲ.A laser ray-tracing wavefront aberrometer (iTrace) and a double pass (DP) system (OQAS) assessed ocular MTF for 6.0 mm pupil diameters following dilation.Areas under the MTF (AUMTF) and their correlations were analyzed.Stepwise multiple regression analysis assessed factors affecting the differences between iTrace-and OQAS-derived AUMTF for the early cataract group.Results For both early cataract and control groups,iTrace-derived MTFs were higher than OQAS-derived MTFs across a range of spatial frequencies (P ＜0.01).No significant difference between the two groups occurred for iTrace-derived AUMTF,but the early cataract group had significantly smaller OQAS-derived AUMTF than did the control group (P ＜0.01).AUMTF determined from both the techniques demonstrated significant correlations with nuclear opacities,higher-order aberrations (HOAs),visual acuity,and contrast sensitivity functions,while the OQAS-derived AUMTF also demonstrated significant correlations with age and cortical opacity grade.The factors significantly affecting the difference between iTrace and OQAS AUMTF were root-mean-squared HOAs (standardized beta coefficient=-0.63,P ＜0.01) and age (standardized beta coefficient=0.26,P ＜0.01).Conclusions MTFs determined from a iTrace and a DP system (OQAS) differ significantly in early cataractous and normal subjects.Correlations with visual performance were higher for the DP system.OQAS-derived MTF may be useful as an indicator of visual performance in early cataract eyes.
BENDING RAY-TRACING BASED ON SIMULATED ANNEALING METHOD%基于模拟退火法的弯曲射线追踪
周竹生; 谢金伟
2011-01-01
This paper proposes a new ray-tracing method based on the concept of simulated annealing. With the new method, not only the problem that the traditional ray-tracing method is over dependent on pre - established initial ray-paths is well solved, but also the quality of desirable ray-paths construction and the associated traveltime calculation between fixed sources and receivers is ensured, even if the model is of much complicated velocity-field. As a result, the ray-paths whose traveltime approach is overall minimum are searched out successfully. Furthermore, the algorithm may calculate ray-paths with local extreme lower traveltime too and restrict them easily by instructing rays to pass through some fixed points. The feasibility and stability of the method have been proved by trial results of theoretical models.%提出了一种新的射线追踪方法——模拟退火法.新方法不仅较好地解决了传统射线追踪方法过分依赖初始模型的问题,而且对于复杂速度场模型也能保证在固定的发射与接收点之间构建令人满意的射线路径及其相应的走时,搜索到满足旅行时全局最小的射线路径.此外,新方法还可计算局部最小旅行时,并可方便地通过指定射线经过固定点来对射线路径进行限制.理论模型的试算结果证明了该方法的可行性和稳健性.
Designing Modular Robotic Playware
Lund, Henrik Hautop; Marti, Patrizia
2009-01-01
In this paper, we explore the design of modular robotic objects that may enhance playful experiences. The approach builds upon the development of modular robotics to create a kind of playware, which is flexible in both set-up and activity building for the end-user to allow easy creation of games....... Key features of this design approach are modularity, flexibility, and construction, immediate feedback to stimulate engagement, activity design by end-users, and creative exploration of play activities. These features permit the use of such modular playware by a vast array of users, including disabled...
Kolkoori, Sanjeevareddy; Hoehne, Christian; Prager, Jens; Rethmeier, Michael; Kreutzbruck, Marc
2014-02-01
Quantitative evaluation of ultrasonic C-scan images in homogeneous and layered anisotropic austenitic materials is of general importance for understanding the influence of anisotropy on wave fields during ultrasonic non-destructive testing and evaluation of these materials. In this contribution, a three dimensional ray tracing method is presented for evaluating ultrasonic C-scan images quantitatively in general homogeneous and layered anisotropic austenitic materials. The directivity of the ultrasonic ray source in general homogeneous columnar grained anisotropic austenitic steel material (including layback orientation) is obtained in three dimensions based on Lamb's reciprocity theorem. As a prerequisite for ray tracing model, the problem of ultrasonic ray energy reflection and transmission coefficients at an interface between (a) isotropic base material and anisotropic austenitic weld material (including layback orientation), (b) two adjacent anisotropic weld metals and (c) anisotropic weld metal and isotropic base material is solved in three dimensions. The influence of columnar grain orientation and layback orientation on ultrasonic C-scan image is quantitatively analyzed in the context of ultrasonic testing of homogeneous and layered austenitic steel materials. The presented quantitative results provide valuable information during ultrasonic characterization of homogeneous and layered anisotropic austenitic steel materials. Copyright © 2013 Elsevier B.V. All rights reserved.
Amberger, Martin A.; Hoeltig, Michael [University of Hamburg, Institute for Inorganic and Applied Chemistry, Martin-Luther-King-Platz 6, D-20146 Hamburg (Germany); Broekaert, Jose A.C., E-mail: jose.broekaert@chemie.uni-hamburg.d [University of Hamburg, Institute for Inorganic and Applied Chemistry, Martin-Luther-King-Platz 6, D-20146 Hamburg (Germany)
2010-02-15
The use of slurry sampling total reflection X-ray fluorescence spectrometry (SlS-TXRF) for the direct determination of Ca, Cr, Cu, Fe, Mn and Ti in four boron nitride powders has been described. Measurements of the zeta potential showed that slurries with good stabilities can be obtained by the addition of polyethylenimine (PEI) at a concentration of 0.1 wt.% and by adjusting the pH at 4. For the optimization of the concentration of boron nitride in the slurries the net line intensities and the signal to background ratios were determined for the trace elements Ca and Ti as well as for the internal standard element Ga in the case of concentrations of boron nitride ranging from 1 to 30 mg mL{sup -1}. As a compromise with respect to high net line intensities and high signal to background ratios, concentrations of 5 mg mL{sup -1} of boron nitride were found suitable and were used for all further measurements. The limits of detection of SlS-TXRF for the boron nitride powders were found to range from 0.062 to 1.6 mug g{sup -1} for Cu and Ca, respectively. Herewith, they are higher than those obtained in solid sampling and slurry sampling graphite furnace atomic absorption spectrometry (SoS-GFAAS, SlS-GFAAS) as well as those of solid sampling electrothermal evaporation inductively coupled plasma optical emission spectrometry (SoS-ETV-ICP-OES). For Ca and Fe as well as for Cu and Fe, however, they were found to be lower than for GFAAS and for ICP-OES subsequent to wet chemical digestion, respectively. The universal applicability of SlS-TXRF to the analysis of samples with a wide variety of matrices could be demonstrated by the analysis of certified reference materials such as SiC, Al{sub 2}O{sub 3}, powdered bovine liver and borate ore with a single calibration. The correlation coefficients of the plots for the values found for Ca, Fe and Ti by SlS-TXRF in the boron nitride powders as well as in the before mentioned samples versus the reference values for the respective
Tibaldo, L
2015-01-01
Cosmic rays up to at least PeV energies are usually described in the framework of an elementary scenario that involves acceleration by objects that are located in the disk of the Milky Way, such as supernova remnants or massive star-forming regions, and then diffusive propagation throughout the Galaxy. Details of the propagation process are so far inferred mainly from the composition of cosmic rays measured near the Earth and then extrapolated to the whole Galaxy. The details of the propagation in the Galactic halo and the escape into the intergalactic medium remain uncertain. The densities of cosmic rays in specific locations can be traced via the gamma rays they produce in inelastic collisions with clouds of interstellar gas. Therefore, we analyze 73 months of Fermi-LAT data from 300 MeV to 10 GeV in the direction of several high- and intermediate-velocity clouds that are located in the halo of the Milky Way. These clouds are supposed to be free of internal sources of cosmic rays and hence any gamma-ray emi...
Marguí, E., E-mail: eva.margui@udg.edu [Department of Chemistry, University of Girona, Campus Montilivi, 17071 Girona (Spain); Zawisza, B.; Skorek, R. [Institute of Chemistry, University of Silesia, Szkolna 9, 40-006 Katowice (Poland); Theato, T. [SPECTRO Analytical Instruments GmbH, Boschstr. 10, 47533 Kleve (Germany); Queralt, I. [Laboratory of X-Ray Analytical Applications, Institute of Earth Sciences Jaume Almera, CSIC, Solé Sabarís s/n, 08028 Barcelona (Spain); Hidalgo, M. [Department of Chemistry, University of Girona, Campus Montilivi, 17071 Girona (Spain); Sitko, R. [Institute of Chemistry, University of Silesia, Szkolna 9, 40-006 Katowice (Poland)
2013-10-01
This study was aimed to achieve improved instrumental sensitivity and detection limits for multielement determination of V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Se, Pb and Cd in liquid samples by using different X-ray fluorescence (XRF) configurations (a benchtop energy-dispersive X-ray fluorescence spectrometer, a benchtop polarised energy-dispersive X-ray fluorescence spectrometer and a wavelength-dispersive X-ray fluorescence spectrometer). The preconcentration of metals from liquid solutions consisted on a solid-phase extraction using carbon nanotubes (CNTs) as solid sorbents. After the extraction step, the aqueous sample was filtered and CNTs with the absorbed elements were collected onto a filter paper which was directly analyzed by XRF. The calculated detection limits in all cases were in the low ng mL{sup −1} range. Nevertheless, results obtained indicate the benefits, in terms of sensitivity, of using polarized X-ray sources using different secondary targets in comparison to conventional XRF systems, above all if Cd determination is required. The developed methodologies, using the aforementioned equipments, have been applied for multielement determination in water samples from an industrial area of Poland. - Highlights: • Use of carbon nanotubes for preconcentration of V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Se, Pb and Cd • Combination of this preconcentration procedure with different XRF systems • Benefit of using polarized X-ray sources for trace element determination.
Modular Forms and Weierstrass Mock Modular Forms
Amanda Clemm
2016-02-01
Full Text Available Alfes, Griffin, Ono, and Rolen have shown that the harmonic Maass forms arising from Weierstrass ζ-functions associated to modular elliptic curves “encode” the vanishing and nonvanishing for central values and derivatives of twisted Hasse-Weil L-functions for elliptic curves. Previously, Martin and Ono proved that there are exactly five weight 2 newforms with complex multiplication that are eta-quotients. In this paper, we construct a canonical harmonic Maass form for these five curves with complex multiplication. The holomorphic part of this harmonic Maass form arises from the Weierstrass ζ-function and is referred to as the Weierstrass mock modular form. We prove that the Weierstrass mock modular form for these five curves is itself an eta-quotient or a twist of one. Using this construction, we also obtain p-adic formulas for the corresponding weight 2 newform using Atkin’s U-operator.
A dictionary of modular threefolds
Meyer, Christian
2005-01-01
The thesis deals with the modularity conjecture for three-dimensional Calabi-Yau varieties. This is a generalization of the work of A. Wiles and others on modularity of elliptic curves. Modularity connects the number of points on varieties with coefficients of certain modular forms. In chapter 1 we collect the basics on arithmetic on Calabi-Yau manifolds, including general modularity results and strategies for modularity proofs. In chapters 2, 3, 4 and 5 we investigate exa...
Supercongruences via modular forms
Osburn, Robert
2009-01-01
We prove two supercongruences for the coefficients of power series expansions in t of modular forms where t is a modular function. As a result, we settle two recent conjectures of Chan, Cooper and Sica. Additionally, we provide a table of supercongruences for numbers which appear in similar power series expansions and in the study of integral solutions of Apery-like differential equations.
Bahr, Patrick
2012-01-01
Tree automata are traditionally used to study properties of tree languages and tree transformations. In this paper, we consider tree automata as the basis for modular and extensible recursion schemes. We show, using well-known techniques, how to derive from standard tree automata highly modular r...
None
2002-12-01
This fact sheet provides information about modular biomass systems. Small modular biomass systems can help supply electricity to rural areas, businesses, and the billions of people who live without power worldwide. These systems use locally available biomass fuels such as wood, crop waste, animal manures, and landfill gas.
Bahr, Patrick
2012-01-01
Tree automata are traditionally used to study properties of tree languages and tree transformations. In this paper, we consider tree automata as the basis for modular and extensible recursion schemes. We show, using well-known techniques, how to derive from standard tree automata highly modular...
Modular Abelian Varieties of Odd Modular Degree
Yazdani, Soroosh
2009-01-01
In this paper, we will study modular Abelian varieties with odd congruence numbers by examining the cuspidal subgroup of $J_0(N)$. We will show that the conductor of such Abelian varieties must be of a special type. For example, if $N$ is the conductor of an absolutely simple modular Abelian variety with an odd congruence number, then $N$ has at most two prime divisors, and if $N$ is odd, then $N=p^\\alpha$ or $N=pq$ for some prime $p$ and $q$. In the second half of this paper, we will focus o...
Baba, Y., E-mail: baba.yuji@jaea.go.jp; Shimoyama, I.; Hirao, N.
2016-10-30
Highlights: • Total-reflection XPS for Na, Rb, and Cs on micaceous oxide were measured. • Detection limit of 100 pg cm{sup −2} was achieved in Cs, corresponding to 200 Bq of {sup 137}Cs (t{sub 1/2} = 30.2 y). • Cs sorbed in micaceous oxides is found ionically bonded with oxygen atoms. - Abstract: In order to determine the chemical states of radioactive cesium ({sup 137}Cs or {sup 134}Cs) sorbed in clay minerals, chemical states of cesium as well as the other alkali metals (sodium and rubidium) sorbed in micaceous oxides have been investigated by X-ray photoelectron spectroscopy (XPS). Since the number of atoms in radioactive cesium is extremely small, we specially focused on chemical states of trace-level alkali metals. For this purpose, we have measured XPS under X-ray total reflection (TR) condition. For cesium, it was shown that ultra-trace amount of cesium down to about 100 pg cm{sup −2} can be detected by TR-XPS. This amount corresponds to about 200 Bq of {sup 137}Cs (t{sub 1/2} = 30.2 y). It was demonstrated that ultra-trace amount of cesium corresponding to radioactive cesium level can be measured by TR-XPS. As to the chemical states, it was found that core-level binding energy in TR-XPS for trace-level cesium shifted to lower-energy side compared with that for thicker layer. A reverse tendency is observed in sodium. Based on charge transfer within a simple point-charge model, it is concluded that chemical bond between alkali metal and micaceous oxide for ultra-thin layer is more polarized that for thick layer.
Gastellu-Etchegorry, Jean-Philippe; Yin, Tiangang; Lauret, Nicolas; Grau, Eloi; Rubio, Jeremy; Cook, Bruce D.; Morton, Douglas C.; Sun, Guoqing
2016-01-01
Light Detection And Ranging (LiDAR) provides unique data on the 3-D structure of atmosphere constituents and the Earth's surface. Simulating LiDAR returns for different laser technologies and Earth scenes is fundamental for evaluating and interpreting signal and noise in LiDAR data. Different types of models are capable of simulating LiDAR waveforms of Earth surfaces. Semi-empirical and geometric models can be imprecise because they rely on simplified simulations of Earth surfaces and light interaction mechanisms. On the other hand, Monte Carlo ray tracing (MCRT) models are potentially accurate but require long computational time. Here, we present a new LiDAR waveform simulation tool that is based on the introduction of a quasi-Monte Carlo ray tracing approach in the Discrete Anisotropic Radiative Transfer (DART) model. Two new approaches, the so-called "box method" and "Ray Carlo method", are implemented to provide robust and accurate simulations of LiDAR waveforms for any landscape, atmosphere and LiDAR sensor configuration (view direction, footprint size, pulse characteristics, etc.). The box method accelerates the selection of the scattering direction of a photon in the presence of scatterers with non-invertible phase function. The Ray Carlo method brings traditional ray-tracking into MCRT simulation, which makes computational time independent of LiDAR field of view (FOV) and reception solid angle. Both methods are fast enough for simulating multi-pulse acquisition. Sensitivity studies with various landscapes and atmosphere constituents are presented, and the simulated LiDAR signals compare favorably with their associated reflectance images and Laser Vegetation Imaging Sensor (LVIS) waveforms. The LiDAR module is fully integrated into DART, enabling more detailed simulations of LiDAR sensitivity to specific scene elements (e.g., atmospheric aerosols, leaf area, branches, or topography) and sensor configuration for airborne or satellite LiDAR sensors.
Wee, Tae-Kwon; Kuo, Ying-Hwa; Lee, Dong-Kyou
2010-12-01
A two-dimensional curved ray tracer (CRT) is developed to study the propagation path of radio signals across a heterogeneous planetary atmosphere. The method, designed to achieve improvements in both computational efficiency and accuracy over conventional straight-line methods, takes rays' first-order bending into account to better describe curved raypaths in the stratified atmosphere. CRT is then used to simulate the phase path from GPS radio occultation (RO). The merit of the ray tracing approach in GPS RO is explicit consideration of horizontal variation in the atmosphere, which may lead to a sizable error but is disregarded in traditional retrieval schemes. In addition, direct modeling of the phase path takes advantage of simple error characteristics in the measurement. With provision of ionospheric and neutral atmospheric refractive indices, in this effort, rays are traced along the full range of GPS-low Earth orbiting (LEO) radio links just as the measurements are made in real life. Here, ray shooting is employed to realize the observed radio links with controlled accuracy. CRT largely reproduces the very measured characteristics of GPS signals. When compared, the measured and simulated phases show remarkable agreement. The cross validation between CRT and GPS RO has confirmed not only the strength of CRT but also the high accuracy of GPS RO measurements. The primary motivation for this study is enabling effective quality control for GPS RO data, overcoming a complicated error structure in the high-level data. CRT has also shown a great deal of potential for improved utilization of GPS RO data for geophysical research.
Kohei Arai
2012-06-01
Full Text Available Simulation method of sea water which contains spherical and non-spherical particles of suspended solid and phytoplankton based on Monte Carlo Ray Tracing: MCRT is proposed for identifying non-spherical species of phytoplankton. From the simulation results, it is found that the proposed MCRT model is validated. Also some possibility of identification of spherical and non-spherical shapes of particles which are contained in sea water is shown. Meanwhile, simulations with the different shape of particles, Prolate and Oblate show that Degree of Polarization: DP depends on shapes. Therefore, non-spherical shape of phytoplankton can be identified with polarization characteristics measurements of the ocean.
Kohei Arai
2013-04-01
Full Text Available Comparative study on linear and nonlinear mixed pixel models of which pixels in remote sensing satellite images is composed with plural ground cover materials mixed together, is conducted for remote sensing satellite image analysis. The mixed pixel models are based on Cierniewski of ground surface reflectance model. The comparative study is conducted by using of Monte Carlo Ray Tracing: MCRT simulations. Through simulation study, the difference between linear and nonlinear mixed pixel models is clarified. Also it is found that the simulation model is validated.
Slot Thing, Rune; Bernchou, Uffe; Mainegra-Hing, Ernesto;
2013-01-01
Abstract Purpose. Cone beam computed tomography (CBCT) image quality is limited by scattered photons. Monte Carlo (MC) simulations provide the ability of predicting the patient-specific scatter contamination in clinical CBCT imaging. Lengthy simulations prevent MC-based scatter correction from...... and pelvis scan were simulated within 2% statistical uncertainty in two hours per scan. Within the same time, the ray tracing algorithm provided the primary signal for each of the projections. Thus, all the data needed for MC-based scatter correction in clinical CBCT imaging was obtained within two hours per...
Claudiu Pozna
2007-08-01
Full Text Available The present paper intention is to develop a kinematical foundation for our nextworks in industrial robots (IR modular design. The goal of this works is todevelop cheap and improved robots which are adapted to the costumer needs. Inorder to achieve the mentioned goal, in [43], we have started a bibliographicalresearch of the main modular design aspects. The mentioned analyze of the actualresults in modular robots design gives us the possibility to establish our researchprogram. The idea of this paper is to develop a kinematical formalism which willbe use in the next dedicated to this subject.
Exploring Modularity in Services
Avlonitis, Viktor; Hsuan, Juliana
2017-01-01
Purpose The purpose of this paper is to examine how modularity manifests in the design of services. The study brings new insights on the organization of service firms by empirically exploring and theoretically advancing the intersection of modularity and service design. Design/methodology/approac......Purpose The purpose of this paper is to examine how modularity manifests in the design of services. The study brings new insights on the organization of service firms by empirically exploring and theoretically advancing the intersection of modularity and service design. Design...... concept), intra-firm organization (service delivery system), and inter-firm relationships (service network). They posit that service architectures require the examination of different analytical levels due to the complex and dynamic nature of service business. Additionally, the analysis provides new...
Kadota, K; Kadota, Kenji; Stewart, Ewan D.
2003-01-01
We present a modular cosmology scenario where the difficulties encountered in conventional modular cosmology are solved in a self-consistent manner, with definite predictions to be tested by observation. Notably, the difficulty of the dilaton finding its way to a precarious weak coupling minimum is made irrelevant by having eternal modular inflation at the vacuum supersymmetry breaking scale after the dilaton is stabilised. Neither this eternal inflation nor the subsequent non-slow-roll modular inflation destabilise the dilaton from its precarious minimum due to the low energy scale of the inflation and consequent small back reaction on the dilaton potential. The observed flat CMB spectrum is obtained from fluctuations in the angular component of a modulus near a symmetric point, which are hugely magnified by the roll down of the modulus to Planckian values, allowing them to dominate the final curvature perturbation. We also give precise calculations of the spectral index and its running.
Hu, Jian-Ying; Hirokawa, Takeshi; Nishiyama, Fumitaka; Kimura, Goji; Kiso, Yoshiyuki; Ito, Kazuaki; Shoto, Eiji [Hiroshima Univ., Higashi-Hiroshima (Japan). Faculty of Engineering
1993-12-31
A misch metal, an alloy of light rare earth elements, was analyzed by a new coupled analytical method, ITP-PIXE (isotachophoresis - Particle Induced X-ray Emission): The sample solution containing ca.1 mg misch metal was separated and fractionated by the use of a preparative isotachophoretic analyzer. The dropwise fractions containing nanomole rare earth elements were analyzed off-line by PIXE. The matrix effect in X-ray measurement was reduced by the isotachophoretic removing of the dominant lanthanoids and preconcentration of the trace elements of interest. Consequently the minor elements, Sm, Gd, Tb, Dy, Ho, Er, Yb and Y could be determined accurately. The most trace element found was Yb (4ppm, 4ng in 1mg sample). The good accuracy of ITP-PIXE method was also demonstrated for several model samples of lanthanoids, where La was the dominant element and the thirteen lanthanoids were the minor elements. The ratio was varied from 500:1 to 50000:1. Even in the case of 50000:1, ca.10% accuracy was achieved for each minor element except for Sm(23%), Gd(17%) and Yb(18%). The analytical results by ITP-PIXE were compared with those by means of ICP-AES (Inductively Coupled Plasma - Atomic Emission Spectrometry). (author).
Feizi, Sepehr; Delfazayebaher, Siamak; Ownagh, Vahid; Sadeghpour, Fatemeh
2017-08-03
To evaluate the agreement between total corneal astigmatism calculated by vector summation of anterior and posterior corneal astigmatism (TCAVec) and total corneal astigmatism measured by ray tracing (TCARay). This study enrolled a total of 204 right eyes of 204 normal subjects. The eyes were measured using a Galilei double Scheimpflug analyzer. The measured parameters included simulated keratometric astigmatism using the keratometric index, anterior corneal astigmatism using the corneal refractive index, posterior corneal astigmatism, and TCARay. TCAVec was derived by vector summation of the astigmatism on the anterior and posterior corneal surfaces. The magnitudes and axes of TCAVec and TCARay were compared. The Pearson correlation coefficient and Bland-Altman plots were used to assess the relationship and agreement between TCAVec and TCARay, respectively. The mean TCAVec and TCARay magnitudes were 0.76±0.57D and 1.00±0.78D, respectively (Pvector summation and ray tracing methods cannot be used interchangeably. There was a systematic error between the TCAVec and TCARay magnitudes. Copyright © 2017 Spanish General Council of Optometry. Published by Elsevier España, S.L.U. All rights reserved.
Berry, Jonna Elizabeth [Iowa State Univ., Ames, IA (United States)
2016-10-25
This dissertation describes a variety of studies on the determination of trace elements in samples with forensic importance. Laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) was used to determine the trace element composition of numerous lipstick samples. Lipstick samples were determined to be homogeneous. Most lipstick samples of similar colors were readily distinguishable at a 95% confidence interval based on trace element composition. Numerous strands of a multi-strand speaker cable were analyzed by LA-ICP-MS. The strands in this study are spatially heterogeneous in trace element composition. In actual forensic applications, the possibility of spatial heterogeneity must be considered, especially in cases where only small samples (e.g., copper wire fragments after an explosion) are available. The effects of many unpredictable variables, such as weather, temperature, and human activity, on the retention of gunshot residue (GSR) around projectile wounds were assessed with LAICP- MS. Skin samples around gunshot and stab wounds and larvae feeding in and around the wounds on decomposing pig carcasses were analyzed for elements consistent with GSR (Sb, Pb, Ba, and Cu). These elements were detected at higher levels in skin and larvae samples around the gunshot wounds compared to the stab wounds for an extended period of time throughout decomposition in both a winter and summer study. After decomposition, radiographic images of the pig bones containing possible damage from bullets revealed metallic particles embedded within a number of bones. Metallic particles within the bones were analyzed with x-ray, K-edge densitometry and determined to contain lead, indicating that bullet residue can be retained throughout decomposition and detected within bones containing projectile trauma.
Service Modularity and Architecture
Brax, Saara A.; Bask, Anu; Hsuan, Juliana
2017-01-01
Purpose: Services are highly important in a world economy which has increasingly become service driven. There is a growing need to better understand the possibilities for, and requirements of, designing modular service architectures. The purpose of this paper is to elaborate on the roots of the e......Purpose: Services are highly important in a world economy which has increasingly become service driven. There is a growing need to better understand the possibilities for, and requirements of, designing modular service architectures. The purpose of this paper is to elaborate on the roots...... of the emerging research stream on service modularity, provide a concise overview of existing work on the subject, and outline an agenda for future research on service modularity and architecture. The articles in the special issue offer four diverse sets of research on service modularity and architecture. Design....../methodology/approach: The paper is built on a literature review mapping the current body of literature on the topic and developing future research directions in service modularity and architecture. Findings: The growing focus on services has triggered needs to investigate the suitability and implementation of physical...
Lehmer, B.D; Brandt, W.N.; Schneider, D.P.; Steffen, A.T.; Alexander, D.M.; Bell, E.F.; Hornschemeier, A.E.; McIntosh, D.H.; Bauer, F.E.; Gilli, R.; Mainieri, V.; Silverman, J.D.; Tozzi, P.; Wolf, C.
2008-01-01
We report on the X-ray evolution over the last approx.9 Gyr of cosmic history (i.e., since z = 1.4) of late-type galaxy populations in the Chandra Deep Field-North and Extended Chandra Deep Field-South (CDF-N and E-CDF-S. respectively; jointly CDFs) survey fields. Our late-type galaxy sample consists of 2568 galaxies. which were identified using rest-frame optical colors and HST morphologies. We utilized X-ray stacking analyses to investigate the X-ray emission from these galaxies, emphasizing the contributions from normal galaxies that are not dominated by active galactic nuclei (AGNs). Over this redshift range, we find significant increases (factors of approx. 5-10) in the X-ray-to-optical mean luminosity ratio (L(sub x)/L(sub B)) and the X-ray-to-stellar-mass mean ratio (L(sub x)/M(sub *)) for galaxy populations selected by L(sub B) and M(sub *), respectively. When analyzing galaxy samples selected via SFR, we find that the mean X-ray-to-SFR ratio (L(sub x)/SFR) is consistent with being constant over the entire redshift range for galaxies with SFR = 1-100 Solar Mass/yr, thus demonstrating that X-ray emission can be used as a robust indicator of star-formation activity out to z approx. 1.4. We find that the star-formation activity (as traced by X-ray luminosity) per unit stellar mass in a given redshift bin increases with decreasing stellar mass over the redshift range z = 0.2-1, which is consistent with previous studies of how star-formation activity depends on stellar mass. Finally, we extend our X-ray analyses to Lyman break galaxies at z approx. 3 and estimate that L(sub x)/L(sub B) at z approx. 3 is similar to its value at z = 1.4.
Islam, M J; Reza, A W; Kausar, A S M Z; Ramiah, H
2014-01-01
The advent of technology with the increasing use of wireless network has led to the development of Wireless Body Area Network (WBAN) to continuously monitor the change of physiological data in a cost efficient manner. As numerous researches on wave propagation characterization have been done in intrabody communication, this study has given emphasis on the wave propagation characterization between the control units (CUs) and wireless access point (AP) in a hospital scenario. Ray tracing is a tool to predict the rays to characterize the wave propagation. It takes huge simulation time, especially when multiple transmitters are involved to transmit physiological data in a realistic hospital environment. Therefore, this study has developed an accelerated ray tracing method based on the nearest neighbor cell and prior knowledge of intersection techniques. Beside this, Red-Black tree is used to store and provide a faster retrieval mechanism of objects in the hospital environment. To prove the superiority, detailed complexity analysis and calculations of reflection and transmission coefficients are also presented in this paper. The results show that the proposed method is about 1.51, 2.1, and 2.9 times faster than the Object Distribution Technique (ODT), Space Volumetric Partitioning (SVP), and Angular Z-Buffer (AZB) methods, respectively. To show the various effects on received power in 60 GHz frequency, few comparisons are made and it is found that on average -9.44 dBm, -8.23 dBm, and -9.27 dBm received power attenuations should be considered when human, AP, and CU move in a given hospital scenario.
M. J. Islam
2014-01-01
Full Text Available The advent of technology with the increasing use of wireless network has led to the development of Wireless Body Area Network (WBAN to continuously monitor the change of physiological data in a cost efficient manner. As numerous researches on wave propagation characterization have been done in intrabody communication, this study has given emphasis on the wave propagation characterization between the control units (CUs and wireless access point (AP in a hospital scenario. Ray tracing is a tool to predict the rays to characterize the wave propagation. It takes huge simulation time, especially when multiple transmitters are involved to transmit physiological data in a realistic hospital environment. Therefore, this study has developed an accelerated ray tracing method based on the nearest neighbor cell and prior knowledge of intersection techniques. Beside this, Red-Black tree is used to store and provide a faster retrieval mechanism of objects in the hospital environment. To prove the superiority, detailed complexity analysis and calculations of reflection and transmission coefficients are also presented in this paper. The results show that the proposed method is about 1.51, 2.1, and 2.9 times faster than the Object Distribution Technique (ODT, Space Volumetric Partitioning (SVP, and Angular Z-Buffer (AZB methods, respectively. To show the various effects on received power in 60 GHz frequency, few comparisons are made and it is found that on average −9.44 dBm, −8.23 dBm, and −9.27 dBm received power attenuations should be considered when human, AP, and CU move in a given hospital scenario.
On sub-modularization and morphological heterogeneity in modular robotics
Lyder, A. H.; Stoy, K.; Garciá, R. F. M.
2012-01-01
Modular robots are a kind of robots built from mechatronic modules, which can be assembled in many different ways allowing the modular robot to assume a wide range of morphologies and functions. An important question in modular robotics is to which degree modules should be heterogeneous...... and implement the Thor robot and evaluate it by participating in the ICRA Planetary Robotic Contingency Challenge. The Thor robot demonstrates that sub-functional modularity and morphological heterogeneity may increase the versatility of modular robots while reducing the complexity of individual modules, which...... in the longer term may lead to more affordable modular robots. © 2013 Springer-Verlag....
On sub-modularization and morphological heterogeneity in modular robotics
Lyder, A. H.; Stoy, K.; Garciá, R. F. M.
2012-01-01
Modular robots are a kind of robots built from mechatronic modules, which can be assembled in many different ways allowing the modular robot to assume a wide range of morphologies and functions. An important question in modular robotics is to which degree modules should be heterogeneous...... and implement the Thor robot and evaluate it by participating in the ICRA Planetary Robotic Contingency Challenge. The Thor robot demonstrates that sub-functional modularity and morphological heterogeneity may increase the versatility of modular robots while reducing the complexity of individual modules, which...... in the longer term may lead to more affordable modular robots. © 2013 Springer-Verlag....
Tibaldo, L.; Digel, S. W.; Franckowiak, A.; Moskalenko, I. V.; Negro, M.; Orlando, E.; Porter, T. A.; Reimer, O. [W. W. Hansen Experimental Physics Laboratory, Kavli Institute for Particle Astrophysics and Cosmology, Department of Physics and SLAC National Accelerator Laboratory, Stanford University, Stanford, CA 94305 (United States); Casandjian, J. M.; Grenier, I. A.; Marshall, D. J. [Laboratoire AIM, CEA-IRFU/CNRS/Université Paris Diderot, Service d’Astrophysique, CEA Saclay, F-91191 Gif sur Yvette (France); Jóhannesson, G. [Science Institute, University of Iceland, IS-107 Reykjavik (Iceland); Strong, A. W., E-mail: ltibaldo@slac.stanford.edu, E-mail: digel@stanford.edu [Max-Planck Institut für extraterrestrische Physik, D-85748 Garching (Germany)
2015-07-10
It is widely accepted that cosmic rays (CRs) up to at least PeV energies are Galactic in origin. Accelerated particles are injected into the interstellar medium where they propagate to the farthest reaches of the Milky Way, including a surrounding halo. The composition of CRs coming to the solar system can be measured directly and has been used to infer the details of CR propagation that are extrapolated to the whole Galaxy. In contrast, indirect methods, such as observations of γ-ray emission from CR interactions with interstellar gas, have been employed to directly probe the CR densities in distant locations throughout the Galactic plane. In this article we use 73 months of data from the Fermi Large Area Telescope in the energy range between 300 MeV and 10 GeV to search for γ-ray emission produced by CR interactions in several high- and intermediate-velocity clouds (IVCs) located at up to ∼7 kpc above the Galactic plane. We achieve the first detection of IVCs in γ rays and set upper limits on the emission from the remaining targets, thereby tracing the distribution of CR nuclei in the halo for the first time. We find that the γ-ray emissivity per H atom decreases with increasing distance from the plane at 97.5% confidence level. This corroborates the notion that CRs at the relevant energies originate in the Galactic disk. The emissivity of the upper intermediate-velocity Arch hints at a 50% decline of CR densities within 2 kpc from the plane. We compare our results to predictions of CR propagation models.
Petitgirard, Sylvain; Daniel, Isabelle; Dabin, Yves; Cardon, Hervé; Tucoulou, Rémi; Susini, Jean
2009-03-01
We present a new diamond anvil cell (DAC), hereafter called the fluoX DAC, dedicated for x-ray fluorescence (XRF) analysis of trace elements in fluids under high pressure and high temperature to 10 GPa and 1273 K at least. This new setup has allowed measurement of Rb, Sr, Y, Zr, with concentrations of 50 ppm to 5.6 GPa and 1273 K. The characteristics of the fluoX DAC consist in an optimized shielding and collection geometry in order to reduce the background level in XRF spectrum. Consequently, minimum detection limits of 0.3 ppm were calculated for the abovementioned elements in this new setup. This new DAC setup coupled to the hard x-rays focusing beamline ID22 (ESRF, France) offers the possibility to analyze in situ at high pressure and high temperature, ppm level concentrations of heavy elements, rare earth elements, and first transition metals, which are of prime importance in geochemical processes. The fluoX DAC is also suitable to x-ray diffraction over the same high pressure-temperature range.
Modular Curvature for Noncommutative Two-Tori
Connes, Alain
2011-01-01
Starting from the description of the conformal geometry of noncommutative 2-tori in the framework of modular spectral triples, we explicitly compute the local curvature functionals determined by the value at zero of the zeta functions affiliated with these spectral triples. We give a closed formula for the Ray-Singer analytic torsion in terms of the Dirichlet quadratic form and the generating function for Bernoulli numbers applied to the modular operator. The gradient of the Ray-Singer analytic torsion is then expressed in terms of these functionals, and yields the analogue of scalar curvature. Computing this gradient in two ways elucidates the meaning of the complicated two variable functions occurring in the formula for the scalar curvature. Moreover, the corresponding evolution equation for the metric produces the appropriate analogue of Ricci curvature. We prove the analogue of the classical result which asserts that in every conformal class the maximum value of the determinant of the Laplacian on metrics...
Khuder, A. [Department of Chemistry, Atomic Energy Commission, P.O. Box 6091, Damascus (Syrian Arab Republic)], E-mail: scientific2@aec.org.sy; Sawan, M.Kh.; Karjou, J. [Department of Chemistry, Atomic Energy Commission, P.O. Box 6091, Damascus (Syrian Arab Republic); Razouk, A.K. [Department of Agriculture, Atomic Energy Commission, P.O. Box 6091, Damascus (Syrian Arab Republic)
2009-07-15
X-ray fluorescence (XRF) and total-reflection X-ray fluorescence (TXRF) techniques suited well for a multi-element determination of K, Ca, Mn, Fe, Cu, Zn, Rb, and Sr in some Syrian medicinal plant species. The accuracy and the precision of both techniques were verified by analyzing the Standard Reference Materials (SRM) peach-1547 and apple leaves-1515. A good agreement between the measured concentrations of the previously mentioned elements and the certified values were obtained with errors less than 10.7% for TXRF and 15.8% for XRF. The determination of Br was acceptable only by XRF with an error less than 24%. Furthermore, the XRF method showed a very good applicability for the determination of K, Ca, Mn, Fe, Cu, Zn, Rb, Sr, and Br in infusions of different Syrian medicinal plant species, namely anise (Anisum vulgare), licorice root (Glycyrrhiza glabra), and white wormwood (Artemisia herba-alba)
Khuder, A.; Sawan, M. Kh.; Karjou, J.; Razouk, A. K.
2009-07-01
X-ray fluorescence (XRF) and total-reflection X-ray fluorescence (TXRF) techniques suited well for a multi-element determination of K, Ca, Mn, Fe, Cu, Zn, Rb, and Sr in some Syrian medicinal plant species. The accuracy and the precision of both techniques were verified by analyzing the Standard Reference Materials (SRM) peach-1547 and apple leaves-1515. A good agreement between the measured concentrations of the previously mentioned elements and the certified values were obtained with errors less than 10.7% for TXRF and 15.8% for XRF. The determination of Br was acceptable only by XRF with an error less than 24%. Furthermore, the XRF method showed a very good applicability for the determination of K, Ca, Mn, Fe, Cu, Zn, Rb, Sr, and Br in infusions of different Syrian medicinal plant species, namely anise ( Anisum vulgare), licorice root ( Glycyrrhiza glabra), and white wormwood ( Artemisia herba-alba).
Pingbo, An; Li, Wang; Hongxi, Lu; Zhiguo, Yu; Lei, Liu; Xin, Xi; Lixia, Zhao; Junxi, Wang; Jinmin, Li
2016-06-01
The internal quantum efficiency (IQE) of the light-emitting diodes can be calculated by the ratio of the external quantum efficiency (EQE) and the light extraction efficiency (LEE). The EQE can be measured experimentally, but the LEE is difficult to calculate due to the complicated LED structures. In this work, a model was established to calculate the LEE by combining the transfer matrix formalism and an in-plane ray tracing method. With the calculated LEE, the IQE was determined and made a good agreement with that obtained by the ABC model and temperature-dependent photoluminescence method. The proposed method makes the determination of the IQE more practical and conventional. Project supported by the National Natural Science Foundation of China (Nos.11574306, 61334009), the China International Science and Technology Cooperation Program (No. 2014DFG62280), and the National High Technology Program of China (No. 2015AA03A101).
Yuan, Cadmus C. A.
2015-12-01
Optical ray tracing modeling applied Beer-Lambert method in the single luminescence material system to model the white light pattern from blue LED light source. This paper extends such algorithm to a mixed multiple luminescence material system by introducing the equivalent excitation and emission spectrum of individual luminescence materials. The quantum efficiency numbers of individual material and self-absorption of the multiple luminescence material system are considered as well. By this combination, researchers are able to model the luminescence characteristics of LED chip-scaled packaging (CSP), which provides simple process steps and the freedom of the luminescence material geometrical dimension. The method will be first validated by the experimental results. Afterward, a further parametric investigation has been then conducted.
Ezoe, Masako; Sasaki, Miho; Hokura, Akiko; Nakai, Izumi [Tokyo Univ. of Science, Faculty of Science, Tokyo (Japan); Terada, Yasuko [Japan Synchrotron Radiation Research Inst., Mikazuki, Hyogo (Japan); Yoshinaga, Tatsuki; Tukamoto, Katsumi [Tokyo Univ., Ocean Research Inst., Tokyo (Japan); Hagiwara, Atsushi [Nagasaki Univ., Graduate School of Science and Technology, Bunkyou, Nagasaki (Japan)
2002-10-01
Two-dimensional imaging and a quantitative analysis of trace elements in rotifer, Brachionus plicatilis, belonging to zooplankton, were carried out by a synchrotron radiation X-ray fluorescence analysis (SR-XRF). The XRF imaging revealed that female rotifers accumulated Fe and Zn in the digestive organ and Fe, Zn, Cu, and Ca in the sexual organs, while the Mn level was high in the head. From a quantitative analysis by inductively coupled plasma mass spectrometry (ICP-MS), we found that rotifers eat the chlorella and accumulate the above elements in the body. The result of quantitative analyses of Mn, Cu, and Zn by SR-XRF in a single sample is in fair agreement with the average values determined by ICP-MS analyses, which were obtained by measuring a large number of rotifers, digested by nitric acid. The present study has demonstrated that SR-XRF is an effective tool for the trace element analysis of a single individual of rotifer. (author)
Krishna, A. Keshav; Khanna, Tarun C.; Mohan, K. Rama
2016-08-01
This paper introduces a calibration procedure and provides the data achieved for accuracy, precision, reproducibility and the detection limits for major (Si, Al, Fe, Mn, Mg, Ca, Na, K, Ti, P) and trace (Ba, Cr, Cu, Hf, La, Nb, Ni, Pb, Rb, Sr, Ta, Th, U, Y, Zn, Zr) elements in the routine analysis of geological and environmental samples. Forty-two rock and soil reference materials were used to calibrate and evaluate the analytical method using a sequential wavelength dispersive X-ray fluorescence spectrometer. Samples were prepared as fused glass discs and analysis performed with a total measuring time of thirty-one minutes. Another set of twelve independent reference materials were analyzed for the evaluation of accuracy. The detection limits and accuracy obtained for the trace elements (1-2 mg/kg) are adequate both for geochemical exploration and environmental studies. The fitness for purpose of the results was also evaluated by the quality criteria test proposed by the International Global Geochemical Mapping Program (IGCP) from which it can be deduced that the method is adequate considering geochemical mapping application and accuracy obtained is within the expected interval of certified values in most cases.
Rucker, Dale F.; Ferré, Ty P. A.
2004-08-01
A MATLAB program was developed to invert first arrival travel time picks from zero offset profiling borehole ground penetrating radar traces to obtain the electromagnetic wave propagation velocities in soil. Zero-offset profiling refers to a mode of operation wherein the centers of the bistatic antennae being lowered to the same depth below ground for each measurement. The inversion uses a simulated annealing optimization routine, whereby the model attempts to reduce the root mean square error between the measured and modeled travel time by perturbing the velocity in a ray tracing routine. Measurement uncertainty is incorporated through the presentation of the ensemble mean and standard deviation from the results of a Monte Carlo simulation. The program features a pre-processor to modify or delete travel time information from the profile before inversion and post-processing through presentation of the ensemble statistics of the water contents inferred from the velocity profile. The program includes a novel application of a graphical user interface to animate the velocity fitting routine.
Modular Optofluidic Systems (MOPS)
Ackermann, Tobias N.; Dietvorst, Jiri; Sanchis, Ana; Salvador, Juan P.; Munoz-Berbel, Xavier; Alvarez-Conde, Erica; Kopp, Daniel; Zappe, Hans; Marco, M.-Pilar; Llobera, Andreu
2016-12-01
Elementary PDMS-based building blocks of fluidic, optical and optofluidic components for Lab on a chip (LOC) platforms has here been developed. All individual modules are compatible and can be anchored and released with the help of puzzle-type connectors This approach is a powerful toolbox to create modular optofluidic systems (MOPS), which can be modified/upgraded to user needs and in-situ reconfigurable. In addition, the PDMS can locally be functionalized, defining a modular biosensor. Measurements in absorbance and fluorescence have been pursued as demonstrator.
Modular assembled space telescope
Feinberg, Lee D.; Budinoff, Jason; MacEwen, Howard; Matthews, Gary; Postman, Marc
2013-09-01
We present a new approach to building a modular segmented space telescope that greatly leverages the heritage of the Hubble Space Telescope and the James Webb Space Telescope. The modular design in which mirror segments are assembled into identical panels allows for economies of scale and for efficient space assembly that make a 20-m aperture approach cost effective. This assembly approach can leverage NASA's future capabilities and has the power to excite the public's imagination. We discuss the science drivers, basic architecture, technology, and leveraged NASA infrastructure, concluding with a proposed plan for going forward.
Brandes, U; Gaertler, M; Goerke, R; Hoefer, M; Nikoloski, Z; Wagner, D
2006-01-01
Several algorithms have been proposed to compute partitions of networks into communities that score high on a graph clustering index called modularity. While publications on these algorithms typically contain experimental evaluations to emphasize the plausibility of results, none of these algorithms has been shown to actually compute optimal partitions. We here settle the unknown complexity status of modularity maximization by showing that the corresponding decision version is NP-complete in the strong sense. As a consequence, any efficient, i.e. polynomial-time, algorithm is only heuristic and yields suboptimal partitions on many instances.
Modular High Voltage Power Supply
Newell, Matthew R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)
2017-05-18
The goal of this project is to develop a modular high voltage power supply that will meet the needs of safeguards applications and provide a modular plug and play supply for use with standard electronic racks.
The Evolution of Modular Construction.
American School & University, 1993
1993-01-01
Explores how the myths of modular construction for schools began; also discusses the advances made in steel and modular construction. The major advantages of using permanent modular construction for schools are highlighted, including its rapid construction, use of standard building materials, financial flexibility, and durability. (GR)
Modular cleanroom construction success.
Möllmann, Markus
2007-09-01
The completion of a 408 m2 major new aseptic pharmacy unit for the St George's Hospital NHS Trust, London, is a significant example of the benefits of using modern modular construction techniques compared to a traditional cleanroom build. At every stage from concept through project planning to final completion, the use of modules proved to be the most appropriate for the task.
Network modularity promotes cooperation.
Marcoux, Marianne; Lusseau, David
2013-05-01
Cooperation in animals and humans is widely observed even if evolutionary biology theories predict the evolution of selfish individuals. Previous game theory models have shown that cooperation can evolve when the game takes place in a structured population such as a social network because it limits interactions between individuals. Modularity, the natural division of a network into groups, is a key characteristic of all social networks but the influence of this crucial social feature on the evolution of cooperation has never been investigated. Here, we provide novel pieces of evidence that network modularity promotes the evolution of cooperation in 2-person prisoner's dilemma games. By simulating games on social networks of different structures, we show that modularity shapes interactions between individuals favouring the evolution of cooperation. Modularity provides a simple mechanism for the evolution of cooperation without having to invoke complicated mechanisms such as reputation or punishment, or requiring genetic similarity among individuals. Thus, cooperation can evolve over wider social contexts than previously reported.
Evolution of Modularity Literature
Frandsen, Thomas
2017-01-01
Purpose The purpose of this paper is to review and analyze the modularity literature to identify the established and emerging perspectives. Design/methodology/approach A systematic literature search and review was conducted through the use of bibliometrics and network analysis. The analysis ident...
Blach, K.
Notatet er på engelsk, idet det er lavet som et oplæg til den internationale standardiseringsorganisations (ISO) arbejde med målkoordinering i byggeriet. Materialet har også været forelagt ekspertgrupperne i CIB W24 og i International Modular Group. Det i notatet præsenterede materiale er blevet ...
Trace determination of uranium in fertilizer samples by total reﬂection X-ray ﬂuorescence
N L Misra; Sangita Dhara; Arijeet Das; G S Lodha; S K Aggarwal; I Varga
2011-02-01
Uranium is reported to be present in phosphate fertilizers. The recovery of uranium from the fertilizers is important because it can be used as fuel in nuclear reactors and also because of environmental concerns. For both these activities suitable method of uranium determinations at trace levels in these fertilizers are required. Studies have been initiated for such TXRF determination of uranium and the results are reported in the present paper. For TXRF determinations the fertilizer samples were processed with nitric acid and the uranium present in it was removed by solvent extraction using tri-n-butyl phosphate as the extractant. The organic phase containing uranium was equilibrated with 1.5% suprapure nitric acid to bring out uranium in aqueous phase. This aqueous phase was mixed with internal standard Y and the TXRF spectra were measured by depositing samples on ﬂoat glass supports. The amounts of uranium in four fertilizer samples of Hungarian origin were determined by processing these TXRF spectra. Uranium concentrations in two fertilizer samples were found to be in the range of 4–6 /, whereas two fertilizer samples did not show the presence of uranium. The precision of the TXRF determination of uranium was found to be better than 8 % (1).
Miksat, J.; Müller, T. M.; Wenzel, F.
2008-07-01
Finite difference (FD) simulation of elastic wave propagation is an important tool in geophysical research. As large-scale 3-D simulations are only feasible on supercomputers or clusters, and even then the simulations are limited to long periods compared to the model size, 2-D FD simulations are widespread. Whereas in generally 3-D heterogeneous structures it is not possible to infer the correct amplitude and waveform from 2-D simulations, in 2.5-D heterogeneous structures some inferences are possible. In particular, Vidale & Helmberger developed an approach that simulates 3-D waveforms using 2-D FD experiments only. However, their method requires a special FD source implementation technique that is based on a source definition which is not any longer used in nowadays FD codes. In this paper, we derive a conversion between 2-D and 3-D Green tensors that allows us to simulate 3-D displacement seismograms using 2-D FD simulations and the actual ray path determined in the geometrical optic limit. We give the conversion for a source of a certain seismic moment that is implemented by incrementing the components of the stress tensor. Therefore, we present a hybrid modelling procedure involving 2-D FD and kinematic ray-tracing techniques. The applicability is demonstrated by numerical experiments of elastic wave propagation for models of different complexity.
Wahlberg, J.S.
1981-01-01
Low levels of selenium (0.1-500 ppm) in both organic and inorganic geologic materials can be semiquantitatively measured by isolating Se as a thin film for presentation to an energy-dispersive X-ray fluorescence spectrometer. Suitably pulverized samples are first digested by fusing with a mixture of Na2CO3 and Na2O2. The fusion cake is dissolved in distilled water, buffered with NH4Cl, and filtered to remove Si and the R2O3 group. A carrier solution of Na2TeO4, plus solid KI, hydrazine sulfate and Na2SO3, is added to the filtrate. The solution is then vacuum-filtered through a 0.45-??m pore-size filter disc. The filter, with the thin film of precipitate, is supported between two sheets of Mylar?? film for analysis. Good agreement is shown between data reported in this study and literature values reported by epithermal neutron-activation analysis and spectrofluorimetry. The method can be made quantitative by utilizing a secondary precipitation to assure complete recovery of the Se. The X-ray method offers fast turn-around time and a reasonably high production rate. ?? 1981.
Alxneit, I. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)
1999-08-01
The program RAY was developed to perform Monte-Carlo simulations of the flux distribution in solar reactors in connection with an arbitrary heliostat field. The code accounts for the shading of the incoming rays from the sun due to the reactor supporting tower as well as for full blocking and shading of the heliostats among themselves. A simplified falling particle reactor (FPR) was evaluated. A central receiver field was used with a total area of 311 m{sup 2} composed of 176 round, focusing heliostats. No attempt was undertaken to optimise either the geometry of the heliostat field nor the aiming strategy of the heliostats. The FPR was evaluated at two different geographic latitudes (-8.23W/47.542N; PSI and -8.23W/20.0N) and during the course of a day (May 30{sup th}). The incident power passing through the reactor aperture and the flux density distribution within the FPR was calculated. (author) 3 figs., 1 tab., 3 refs.
Maruthi, Y. A.; Das, N. Lakshmana; Ramprasad, S.; Ram, S. S.; Sudarshan, M.
2015-08-01
The present studies focus the quantitative analysis of elements in school chalk to ensure the safety of its use. The elements like Calcium (Ca), Aluminum (Al), Iron (Fe), Silicon (Si) and Chromium (Cr) were analyzed from settled chalk dust samples collected from five classrooms (CD-1) and also from another set of unused chalk samples collected from local market (CD-2) using Energy Dispersive X-Ray florescence(ED-XRF) spectroscopy. Presence of these elements in significant concentrations in school chalk confirmed that, it is an irritant and occupational hazard. It is suggested to use protective equipments like filtered mask for mouth, nose and chalk holders. This study also suggested using the advanced mode of techniques like Digital boards, marker boards and power point presentations to mitigate the occupational hazard for classroom chalk
董建军; 杨正华; 曹柱荣; 韦敏习; 詹夏宇; 刘慎业; 丁永坤
2011-01-01
The spatial resolution of KBA X-ray microscope is studied with ray-tracing simulation and experimental test. In the experiment, the imaging object is Au grid, backlit by X-rays produced by the 9th laser interaction with Cu target on Shen-guang II laser facility. The spatial resolution of KBA X-ray microscope is found to be asymmetric about the center of its field of view. Moreover, the experimental data show that, the variation of resolution in the reducing direction of grazing incidence angle is smaller than that in the increasing direction, and the resolution asymmetry is about 30% relative to the field center.%通过光线追踪模拟在SGⅡ激光装置上利用第9路激光入射到Cu背光靶面产生X射线,通过Au网格背光照相,利用KBA显微镜对此网格成像,获得了清晰的网格图像.通过对实验网格数据的分析发现:在掠射角减小的方向,空间分辨力随视场的变化比掠射角增大的方向变化小,与光线追踪模拟比较,二者均表明KBA的视场是非对称的,从实验图像数据得出,视场的不对称相对于中心位置约为30％.
Ran, Jing; Wang, Dejian; Wang, Can; Zhang, Gang; Yao, Lipeng
2014-08-01
Portable X-ray fluorescence (PXRF) spectrometry may be very suitable for a fast and effective environmental assessment and source identification of trace metals in soils. In this study, topsoils (0-10 cm) at 139 sites were in situ scanned for total trace metals (Cr, Cu, Ni, Pb and Zn) and arsenic concentrations by PXRF in a typical town in Yangtze Delta region of Jiangsu province, China. To validate the utility of PXRF, 53 samples were collected from the scanning sites for the determination of selected trace metals using conventional methods. Based on trace metal concentrations detected by in situ PXRF, the contamination extent and sources of trace metals were studied via geo-accumulation index, multivariate analysis and geostatistics. The trace metal concentrations determined by PXRF were similar to those obtained via conventional chemical analysis. The median concentration of As, Cr, Cu, Ni, Pb and Zn in soils were 10.8, 56.4, 41.5, 43.5, 33.5, and 77.7 mg kg(-1), respectively. The distribution patterns of Cr, Cu, Ni, Pb, and Zn were mostly affected by anthropogenic sources, while As was mainly derived from lithogenic sources. Overall, PXRF has been successfully applied to contamination assessment and source identification of trace metals in soils.
Traces of co-evolution in high z X-ray selected and submm-luminous QSOs
Khan-Ali, A; Page, M J; Stevens, J A; Mateos, S; Symeonidis, M; Orjales, J M Cao
2014-01-01
We present a detailed study of a X -ray selected sample of 5 submillimeter bright QSOs at $z\\sim2$, where the highest rates of star formation (SF) and further growth of black holes (BH) occur. Therefore, this sample is a great laboratory to investigate the co-evolution of star formation and AGN. We present here the analysis of the spectral energy distributions (SED) of the 5 QSOS, including new data from Herschel PACS and SPIRE. Both AGN components (direct and reprocessed) and like Star Formation (SF) are needed to model its SED. From the SED and their UV-optical spectra we have estimated the mass of the black hole ($M_{BH} = 10^9 - 10^{10} M_{SUN}$) and bolometric luminosities of AGN ($L_{BOL} = (0.8-20) \\times 10^{13} L_{SUN}$). These objects show very high luminosities in the far infrared range (at the H/ULIRG levels) and very high rates of SF (SFR = 400-1400 $M_{SUN}$/y). Known their current SFR and their BH masses, we deduce that their host galaxies must be already very massive, or would not have time to...
Freidel, Laurent; Minic, Djordje
2016-01-01
At present, our notion of space is a classical concept. Taking the point of view that quantum theory is more fundamental than classical physics, and that space should be given a purely quantum definition, we revisit the notion of Euclidean space from the point of view of quantum mechanics. Since space appears in physics in the form of labels on relativistic fields or Schrodinger wave functionals, we propose to define Euclidean quantum space as a choice of polarization for the Heisenberg algebra of quantum theory. We show, following Mackey, that generically, such polarizations contain a fundamental length scale and that contrary to what is implied by the Schrodinger polarization, they possess topologically distinct spectra. These are the modular spaces. We show that they naturally come equipped with additional geometrical structures usually encountered in the context of string theory or generalized geometry. Moreover, we show how modular space reconciles the presence of a fundamental scale with translation and...
Modularity promotes epidemic recurrence
Jesan, T; Sinha, Sitabhra
2016-01-01
The long-term evolution of epidemic processes depends crucially on the structure of contact networks. As empirical evidence indicates that human populations exhibit strong community organization, we investigate here how such mesoscopic configurations affect the likelihood of epidemic recurrence. Through numerical simulations on real social networks and theoretical arguments using spectral methods, we demonstrate that highly contagious diseases that would have otherwise died out rapidly can persist indefinitely for an optimal range of modularity in contact networks.
Woelfl, S.; Óvári, M.; Nimptsch, J.; Neu, T. R.; Mages, M.
2016-02-01
Element determination in plankton is important for the assessment of metal contamination of aquatic environments. Until recently, it has been difficult to determine elemental content in rotifers or ciliates derived from natural plankton samples because of the difficulty in handling and separation of these fragile organisms. The aim of this study was to evaluate methods for separation of rotifers and large ciliates from natural plankton samples (μg range dry weight) and subsequent analysis of their elemental content using total-reflection X-ray fluorescence spectrometry (TXRF). Plankton samples were collected from different aquatic environments (three lakes, one river) in Chile, Argentina and Hungary. From one to eighty specimens of five rotifer species (Brachionus calyciflorus, Brachionus falcatus, Asplanchna sieboldii, Asplanchna sp., Philodina sp.) and four to twelve specimens of one large ciliate (Stentor amethystinus) were prepared according to the dry method originally developed for microcrustaceans, and analysed by TRXF following in situ microdigestion. Our results demonstrated that it possible to process these small and fragile organisms (individual dry mass: 0.17-9.39 μg ind- 1) via careful washing and preparation procedures. We found species-dependent differences of the element mass fractions for some of the elements studied (Cr, Mn, Fe, Ni, Cu, Zn, As, Pb), especially for Cu, Fe and Mn. One large rotifer species (A. sieboldii) also showed a negative correlation between individual dry weight and the element content for Pb, Ni and Cr. We conclude that our application of the in situ microdigestion-TRXF method is suitable even for rotifers and ciliates, greatly expanding the possibilities for use of plankton in biomonitoring of metal contamination in aquatic environments.
Ibrahim Gaafar
2015-12-01
Full Text Available This study is an attempt to use the gamma ray spectrometric measurements and VLF-EM data to identify the subsurface structure and map uranium mineralization along El Sela shear zone, South Eastern Desert of Egypt. Many injections more or less mineralized with uranium and associated with alteration processes were recorded in El Sela shear zone. As results from previous works, the emplacement of these injections is structurally controlled and well defined by large shear zones striking in an ENE–WSW direction and crosscut by NW–SE to NNW–SSE fault sets. VLF method has been applied to map the structure and the presence of radioactive minerals that have been delineated by the detection of high uranium mineralization. The electromagnetic survey was carried out to detect the presence of shallow and deep conductive zones that cross the granites along ENE–WSW fracturing directions and to map its spatial distribution. The survey comprised seventy N–S spectrometry and VLF-EM profiles with 20 m separation. The resulted data were displayed as composite maps for K, eU and eTh as well as VLF-Fraser map. Twelve profiles with 100 m separation were selected for detailed description. The VLF-EM data were interpreted qualitatively as well as quantitatively using the Fraser and the Karous–Hjelt filters. Fraser filtered data and relative current density pseudo-sections indicate the presence of shallow and deep conductive zones that cross the granites along ENE–WSW shearing directions. High uranium concentrations found just above the higher apparent current-density zones that coincide with El-Sela shear zone indicate a positive relation between conductivity and uranium minerals occurrence. This enables to infer that the anomalies detected by VLF-EM data are due to the highly conductive shear zone enriched with uranium mineralization extending for more than 80 m.
Freidel, Laurent; Leigh, Robert G.; Minic, Djordje
2016-11-01
At present, our notion of space is a classical concept. Taking the point of view that quantum theory is more fundamental than classical physics, and that space should be given a purely quantum definition, we revisit the notion of Euclidean space from the point of view of quantum mechanics. Since space appears in physics in the form of labels on relativistic fields or Schrödinger wave functionals, we propose to define Euclidean quantum space as a choice of polarization for the Heisenberg algebra of quantum theory. We show, following Mackey, that generically, such polarizations contain a fundamental length scale and that contrary to what is implied by the Schrödinger polarization, they possess topologically distinct spectra. These are the modular spaces. We show that they naturally come equipped with additional geometrical structures usually encountered in the context of string theory or generalized geometry. Moreover, we show how modular space reconciles the presence of a fundamental scale with translation and rotation invariance. We also discuss how the usual classical notion of space comes out as a form of thermodynamical limit of modular space while the Schrödinger space is a singular limit.
Javier Valenzuela
2007-06-01
Full Text Available First generation cognitive science has always maintained that the mind/brain is a modular system. This has been especially apparent in linguistics, where the modularity thesis goes largely unquestioned by the linguistic mainstream. Cognitive linguists have long disputed the reality of modular architectures of grammar. Instead of conceiving syntax as a computational system of a relatively small set of formal principles and parameters, cognitive linguists take the notion of grammatical construction to be the basic unit of syntax: syntax is simply our repertoire of form-meaning pairings. On such a view, there is no a-priori reason to believe that semantics and phonology cannot affect syntax. In the present paper, we want to take things a step further and suggest, more generally, that language is not a module of cognition in any strict sense. We present preliminary results from research in progress concerning the effect of music on grammatical constructions. More specifically, our experiment compares reaction times between two grammatical constructions that differ in semantics and intonational curves but share lexical material. Our data so far suggests that subjects take less time reading the construction when the semantic bias and intonation match than in non-matching cases. This, we argue, suggests not only that semantics, phonology and syntax form an information bundle (i.e. a construction in the cognitive linguistic sense, but that perceived similarity of music can influence linguistic cognition.
[Modular enteral nutrition in pediatrics].
Murillo Sanchís, S; Prenafeta Ferré, M T; Sempere Luque, M D
1991-01-01
Modular Enteral Nutrition may be a substitute for Parenteral Nutrition in children with different pathologies. Study of 4 children with different pathologies selected from a group of 40 admitted to the Maternal-Childrens Hospital "Valle de Hebrón" in Barcelona, who received modular enteral nutrition. They were monitored on a daily basis by the Dietician Service. Modular enteral nutrition consists of modules of proteins, peptides, lipids, glucids and mineral salts-vitamins. 1.--Craneo-encephalic traumatisms with loss of consciousness, Feeding with a combination of parenteral nutrition and modular enteral nutrition for 7 days. In view of the tolerance and good results of the modular enteral nutrition, the parenteral nutrition was suspended and modular enteral nutrition alone used up to a total of 43 days. 2.--55% burns with 36 days of hyperproteic modular enteral nutrition together with normal feeding. A more rapid recovery was achieved with an increase in total proteins and albumin. 3.--Persistent diarrhoea with 31 days of modular enteral nutrition, 5 days on parenteral nutrition alone and 8 days on combined parenteral nutrition and modular enteral nutrition. In view of the tolerance and good results of the modular enteral nutrition, the parenteral nutrition was suspended. 4.--Mucoviscidosis with a total of 19 days on modular enteral nutrition, 12 of which were exclusively on modular enteral nutrition and 7 as a night supplement to normal feeding. We administered proteic intakes of up to 20% of the total calorific intake and in concentrations of up to 1.2 calories/ml of the final preparation, always with a good tolerance. Modular enteral nutrition can and should be used as a substitute for parenteral nutrition in children with different pathologies, thus preventing the complications inherent in parenteral nutrition.
Kovács, Z.; Harko, T.
2011-11-01
We present a full general relativistic numerical code for estimating the energy-momentum deposition rate (EMDR) from neutrino pair annihilation (?). The source of the neutrinos is assumed to be a neutrino-cooled accretion disc around neutron and quark stars. We calculate the neutrino trajectories by using a ray-tracing algorithm with the general relativistic Hamilton's equations for neutrinos and derive the spatial distribution of the EMDR due to the annihilations of neutrinos and antineutrinos around rotating neutron and quark stars. We obtain the EMDR for several classes of rotating neutron stars, described by different equations of state of the neutron matter, and for quark stars, described by the Massachusetts Institute of Technology (MIT) bag model equation of state and in the colour-flavour-locked (CFL) phase. The distribution of the total annihilation rate of the neutrino-antineutrino pairs around rotating neutron and quark stars is studied for isothermal discs and accretion discs in thermodynamical equilibrium. We demonstrate both the differences in the equations of state for neutron and quark matter and rotation with the general relativistic effects significantly modify the EMDR of the electrons and positrons generated by the neutrino-antineutrino pair annihilation around compact stellar objects, as measured at infinity.
Xiao, Yi; Tholen, Danny; Zhu, Xin-Guang
2016-11-01
Leaf photosynthesis is determined by biochemical properties and anatomical features. Here we developed a three-dimensional leaf model that can be used to evaluate the internal light environment of a leaf and its implications for whole-leaf electron transport rates (J). This model includes (i) the basic components of a leaf, such as the epidermis, palisade and spongy tissues, as well as the physical dimensions and arrangements of cell walls, vacuoles and chloroplasts; and (ii) an efficient forward ray-tracing algorithm, predicting the internal light environment for light of wavelengths between 400 and 2500nm. We studied the influence of leaf anatomy and ambient light on internal light conditions and J The results show that (i) different chloroplasts can experience drastically different light conditions, even when they are located at the same distance from the leaf surface; (ii) bundle sheath extensions, which are strips of parenchyma, collenchyma or sclerenchyma cells connecting the vascular bundles with the epidermis, can influence photosynthetic light-use efficiency of leaves; and (iii) chloroplast positioning can also influence the light-use efficiency of leaves. Mechanisms underlying leaf internal light heterogeneity and implications of the heterogeneity for photoprotection and for the convexity of the light response curves are discussed.
Woelfl, Stefan; Mercado, Susana; Villalobos, Lorena [Instituto de Zoologia, Universidad Austral de Chile, Casilla 567, Valdivia (Chile); Mages, Margarete; Ovari, Mihaly [Department of Inland Water Research Magdeburg, UFZ Centre for Environmental Research Leipzig-Halle, Brueckstrasse 3a, 39114, Magdeburg (Germany); Encina, Francisco [Escuela de Ciencias Ambientales, Facultad de Ciencias, Universidad Catolica de Temuco, Montt 056, Temuco (Chile)
2004-02-01
First results are described from the application of a recently developed dry method for determination of elements in single specimens of freshwater microcrustaceans, using total reflection X-ray fluorescence spectrometry (TXRF). This method is a powerful, non-destructive technique for quantifying the trace element content of minute biological samples with a dry weight of 3-50 {mu}g. Three different freshwater microcrustaceans were sampled, from the natural, uncontaminated Lake Laja and from the artificial Rapel reservoir which is slightly contaminated by drainage water from a copper mine. Single specimens of Daphnia pulex, Bosmina chilensis, and Ceriodaphnia dubia were prepared using a modification of the dry method and measured by TXRF. The results showed that both As, Mn, Fe, Ni, Zn, and Cu content and the bioaccumulation of these metals were usually significantly different between the microcrustaceans from the two lakes. The largest difference was found for Cu which was eight times more concentrated in the two microcrustaceans from Rapel reservoir than it was in D. pulex from Lake Laja. (orig.)
The modularity of pollination networks
Olesen, Jens Mogens; Bascompte, J.; Dupont, Yoko
2007-01-01
consist of strongly connected species. The importance of modularity has been discussed for a long time, but no consensus on its prevalence in ecological networks has yet been reached. Progress is hampered by inadequate methods and a lack of large datasets. We analyzed 51 pollination networks including...... almost 10,000 species and 20,000 links and tested for modularity by using a recently developed simulated annealing algorithm. All networks with >150 plant and pollinator species were modular, whereas networks with
A Unifying Modularity in Networks
HAO Jun-Jun; CAI Shui-Ming; HE Qin-Bin; LIU Zeng-Rong
2010-01-01
@@ We propose a new modularity criterion in complex networks,called the unifying modularity q which is independent of the number of partitions.It is shown that,for a given network,the relationship between the upper limit of Q and the number of the partitions,k,is sup(Qk)=(k-1)/k.Since the range of Q for each partition number is inconsistent,we try to extend the concept Q to unifying modularity q,which is independent of the number of partitions.Subsequently,we indicate that it is more accurately to determine the number of partitions by using unifying modularity q than Q.
Uniruledness of orthogonal modular varieties
Gritsenko, Valery
2012-01-01
A strongly reflective modular form with respect to an orthogonal group of signature (2,n) determines a Lorentzian Kac--Moody algebra. We find a new geometric application of such modular forms: we prove that if the weight is larger than n then the corresponding modular variety is uniruled. We also construct new reflective modular forms and thus provide new examples of uniruled moduli spaces of lattice polarised K3 surfaces. Finally we prove that the moduli space of Kummer surfaces associated to (1,21)-polarised abelian surfaces is uniruled.
Winther-Hansen, Casper; Frandsen, Thomas
facilitate co-creation through open platforms and service modularity. Based on data from two pharmaceuticals we explore issues of governance related to the relative openness of platforms and their completeness. Whereas some pharmaceuticals should cater to sophisticated needs of competent users through open......Pharmaceuticals increasingly consider the potential of services, as healthcare payers require them to provide data on treatment outcomes. Ranging from corporate websites to free apps, these services are meant to increase the value of product offerings. This paper investigates how services can...
Vranish, John M. (Inventor)
2009-01-01
A gearing system using modular gear bearing components. Each component is composed of a core, one or more modules attached to the core and two or more fastening modules rigidly attaching the modules to the core. The modules, which are attached to the core, may consist of gears, rollers or gear bearing components. The core orientation affects the orientation of the modules attached to the core. This is achieved via the keying arrangement of the core and the component modules that attach to the core. Such an arrangement will also facilitate the phase tuning of gear modules with respect to the core and other gear modules attached to the core.
Modular Biometric Monitoring System
Chmiel, Alan J. (Inventor); Humphreys, Bradley T. (Inventor)
2017-01-01
A modular system for acquiring biometric data includes a plurality of data acquisition modules configured to sample biometric data from at least one respective input channel at a data acquisition rate. A representation of the sampled biometric data is stored in memory of each of the plurality of data acquisition modules. A central control system is in communication with each of the plurality of data acquisition modules through a bus. The central control system is configured to control communication of data, via the bus, with each of the plurality of data acquisition modules.
Modular Mobile Application Design
Jim Hahn
2012-10-01
Full Text Available This article describes the development of the Minrva library app for Android phones. The decisions to build a native application with Java and use a modular design are discussed. The application includes five modules: catalog search, in-building navigation, a barcode scanning feature, and up to date notifications of circulating technology availability. A sixth module, Amazon recommendations, that is not included in the version of the app that was released is also discussed. The article also reports on the findings of two rounds of usability testing and the plans for future development of the app.
Isik, Hakan
This study is premised on the fact that student conceptions of optics appear to be unrelated to student characteristics of gender, age, years since high school graduation, or previous academic experiences. This study investigated the relationships between student characteristics and student performance on image formation test items and the changes in student conceptions of optics after an introductory inquiry-based physics course. Data was collected from 39 college students who were involved in an inquiry-based physics course teaching topics of geometrical optics. Student data concerning characteristics and previous experiences with optics and mathematics were collected. Assessment of student understanding of optics knowledge for pinholes, plane mirrors, refraction, and convex lenses was collected with, the Test of Image Formation with Light-Ray Tracing instrument. Total scale and subscale scores representing the optics instrument content were derived from student pretest and posttest responses. The types of knowledge, needed to answer each optics item correctly, were categorized as situational, conceptual, procedural, and strategic knowledge. These types of knowledge were associated with student correct and incorrect responses to each item to explain the existences and changes in student scientific and naive conceptions. Correlation and stepwise multiple regression analyses were conducted to identify the student characteristics and academic experiences that significantly predicted scores on the subscales of the test. The results showed that student experience with calculus was a significant predictor of student performance on the total scale as well as on the refraction subscale of the Test of Image Formation with Light-Ray Tracing. A combination of student age and previous academic experience with precalculus was a significant predictor of student performance on the pretest pinhole subscale. Student characteristic of years since high school graduation
Modular radiochemistry synthesis system
Satyamurthy, Nagichettiar; Barrio, Jorge R.; Amarasekera, Bernard; Van Dam, Michael R.; Olma, Sebastian; Williams, Dirk; Eddings, Mark; Shen, Clifton Kwang-Fu
2016-11-01
A modular chemical production system includes multiple modules for performing a chemical reaction, particularly of radiochemical compounds, from a remote location. One embodiment comprises a reaction vessel including a moveable heat source with the position thereof relative to the reaction vessel being controllable from a remote position. Alternatively the heat source may be fixed in location and the reaction vial is moveable into and out of the heat source. The reaction vessel has one or more sealing plugs, the positioning of which in relationship to the reaction vessel is controllable from a remote position. Also the one or more reaction vessel sealing plugs can include one or more conduits there through for delivery of reactants, gases at atmospheric or an elevated pressure, inert gases, drawing a vacuum and removal of reaction end products to and from the reaction vial, the reaction vial with sealing plug in position being operable at elevated pressures. The modular chemical production system is assembled from modules which can each include operating condition sensors and controllers configured for monitoring and controlling the individual modules and the assembled system from a remote position. Other modules include, but are not limited to a Reagent Storage and Delivery Module, a Cartridge Purification Module, a Microwave Reaction Module, an External QC/Analysis/Purification Interface Module, an Aliquotting Module, an F-18 Drying Module, a Concentration Module, a Radiation Counting Module, and a Capillary Reactor Module.
Borroni-Bird, Christopher E. (Inventor); Vitale, Robert L. (Inventor); Lee, Chunhao J. (Inventor); Ambrose, Robert O. (Inventor); Bluethmann, William J. (Inventor); Junkin, Lucien Q. (Inventor); Lutz, Jonathan J. (Inventor); Guo, Raymond (Inventor); Lapp, Anthony Joseph (Inventor); Ridley, Justin S. (Inventor)
2015-01-01
A modular robotic vehicle includes a chassis, driver input devices, an energy storage system (ESS), a power electronics module (PEM), modular electronic assemblies (eModules) connected to the ESS via the PEM, one or more master controllers, and various embedded controllers. Each eModule includes a drive wheel containing a propulsion-braking module, and a housing containing propulsion and braking control assemblies with respective embedded propulsion and brake controllers, and a mounting bracket covering a steering control assembly with embedded steering controllers. The master controller, which is in communication with each eModule and with the driver input devices, communicates with and independently controls each eModule, by-wire, via the embedded controllers to establish a desired operating mode. Modes may include a two-wheel, four-wheel, diamond, and omni-directional steering modes as well as a park mode. A bumper may enable docking with another vehicle, with shared control over the eModules of the vehicles.
Preheating after modular inflation
Barnaby, Neil; Bond, J. Richard; Huang, Zhiqi; Kofman, Lev
2009-12-01
We study (p)reheating in modular (closed string) inflationary scenarios, with a special emphasis on Kähler moduli/Roulette models. It is usually assumed that reheating in such models occurs through perturbative decays. However, we find that there are very strong non-perturbative preheating decay channels related to the particular shape of the inflaton potential (which is highly nonlinear and has a very steep minimum). Preheating after modular inflation, proceeding through a combination of tachyonic instability and broad-band parametric resonance, is perhaps the most violent example of preheating after inflation known in the literature. Further, we consider the subsequent transfer of energy to the standard model sector in scenarios where the standard model particles are confined to a D7-brane wrapping the inflationary blow-up cycle of the compactification manifold or, more interestingly, a non-inflationary blow-up cycle. We explicitly identify the decay channels of the inflaton in these two scenarios. We also consider the case where the inflationary cycle shrinks to the string scale at the end of inflation; here a field theoretical treatment of reheating is insufficient and one must turn instead to a stringy description. We estimate the decay rate of the inflaton and the reheat temperature for various scenarios.
Modular radiochemistry synthesis system
Satyamurthy, Nagichettiar; Barrio, Jorge R.; Amarasekera, Bernard; Van Dam, R. Michael; Olma, Sebastian; Williams, Dirk; Eddings, Mark; Shen, Clifton Kwang-Fu
2015-12-15
A modular chemical production system includes multiple modules for performing a chemical reaction, particularly of radiochemical compounds, from a remote location. One embodiment comprises a reaction vessel including a moveable heat source with the position thereof relative to the reaction vessel being controllable from a remote position. Alternatively the heat source may be fixed in location and the reaction vial is moveable into and out of the heat source. The reaction vessel has one or more sealing plugs, the positioning of which in relationship to the reaction vessel is controllable from a remote position. Also the one or more reaction vessel sealing plugs can include one or more conduits there through for delivery of reactants, gases at atmospheric or an elevated pressure, inert gases, drawing a vacuum and removal of reaction end products to and from the reaction vial, the reaction vial with sealing plug in position being operable at elevated pressures. The modular chemical production system is assembled from modules which can each include operating condition sensors and controllers configured for monitoring and controlling the individual modules and the assembled system from a remote position. Other modules include, but are not limited to a Reagent Storage and Delivery Module, a Cartridge Purification Module, a Microwave Reaction Module, an External QC/Analysis/Purification Interface Module, an Aliquotting Module, an F-18 Drying Module, a Concentration Module, a Radiation Counting Module, and a Capillary Reactor Module.
Modular Engineering of Production Plants
Miller, Thomas Dedenroth
1998-01-01
Based on a case-study on design of pharmaceutical production plants, this paper suggests that modularity may support business efficiency for companies with one-of-a-kind production and without in-house manufacturing. Modularity may support efficient management of design knowledge and may facilitate...
Fable: Socially Interactive Modular Robot
Magnússon, Arnþór; Pacheco, Moises; Moghadam, Mikael
2013-01-01
Modular robots have a significant potential as user-reconfigurable robotic playware, but often lack sufficient sensing for social interaction. We address this issue with the Fable modular robotic system by exploring the use of smart sensor modules that has a better ability to sense the behavior...
Modular Decomposition of Boolean Functions
J.C. Bioch (Cor)
2002-01-01
textabstractModular decomposition is a thoroughly investigated topic in many areas such as switching theory, reliability theory, game theory and graph theory. Most appli- cations can be formulated in the framework of Boolean functions. In this paper we give a uni_ed treatment of modular decompositio
Modular Engineering of Production Plants
Miller, Thomas Dedenroth
1998-01-01
Based on a case-study on design of pharmaceutical production plants, this paper suggests that modularity may support business efficiency for companies with one-of-a-kind production and without in-house manufacturing. Modularity may support efficient management of design knowledge and may facilitate...
Modular Decomposition of Boolean Functions
J.C. Bioch (Cor)
2002-01-01
textabstractModular decomposition is a thoroughly investigated topic in many areas such as switching theory, reliability theory, game theory and graph theory. Most appli- cations can be formulated in the framework of Boolean functions. In this paper we give a uni_ed treatment of modular
Quantum modular forms, mock modular forms, and partial theta functions
Kimport, Susanna
Defined by Zagier in 2010, quantum modular forms have been the subject of an explosion of recent research. Many of these results are aimed at discovering examples of these functions, which are defined on the rational numbers and have "nice" modularity properties. Though the subject is in its early stages, numerous results (including Zagier's original examples) show these objects naturally arising from many areas of mathematics as limits of other modular-like functions. One such family of examples is due to Folsom, Ono, and Rhoades, who connected these new objects to partial theta functions (introduced by Rogers in 1917) and mock modular forms (about which there is a rich theory, whose origins date back to Ramanujan in 1920). In this thesis, we build off of the work of Folsom, Ono, and Rhoades by providing an infinite family of quantum modular forms of arbitrary positive half-integral weight. Further, this family of quantum modular forms "glues" mock modular forms to partial theta functions and is constructed from a so-called "universal" mock theta function by extending a method of Eichler and Zagier (originally defined for holomorphic Jacobi forms) into a non-holomorphic setting. In addition to the infinite family, we explore the weight 1/2 and 3/2 functions in more depth. For both of these weights, we are able to explicitly write down the quantum modular form, as well as the corresponding "errors to modularity," which can be shown to be Mordell integrals of specific theta functions and, as a consequence, are real-analytic functions. Finally, we turn our attention to the partial theta functions associated with these low weight examples. Berndt and Kim provide asymptotic expansions for a certain class of partial theta functions as q approaches 1 radially within the unit disk. Here, we extend this work to not only obtain asymptotic expansions for this class of functions as q approaches any root of unity, but also for a certain class of derivatives of these functions
Baran, A. J.; Hesse, Evelyn; Sourdeval, Odran
2017-03-01
Future satellite missions, from 2022 onwards, will obtain near-global measurements of cirrus at microwave and sub-millimetre frequencies. To realise the potential of these observations, fast and accurate light-scattering methods are required to calculate scattered millimetre and sub-millimetre intensities from complex ice crystals. Here, the applicability of the ray tracing with diffraction on facets method (RTDF) in predicting the bulk scalar optical properties and phase functions of randomly oriented hexagonal ice columns and hexagonal ice aggregates at millimetre frequencies is investigated. The applicability of RTDF is shown to be acceptable down to size parameters of about 18, between the frequencies of 243 and 874 GHz. It is demonstrated that RTDF is generally well within about 10% of T-matrix solutions obtained for the scalar optical properties assuming hexagonal ice columns. Moreover, on replacing electromagnetic scalar optical property solutions obtained for the hexagonal ice aggregate with the RTDF counterparts at size parameter values of about 18 or greater, the bulk scalar optical properties can be calculated to generally well within ±5% of an electromagnetic-based database. The RTDF-derived bulk scalar optical properties result in brightness temperature errors to generally within about ±4 K at 874 GHz. Differing microphysics assumptions can easily exceed such errors. Similar findings are found for the bulk scattering phase functions. This finding is owing to the scattering solutions being dominated by the processes of diffraction and reflection, both being well described by RTDF. The impact of centimetre-sized complex ice crystals on interpreting cirrus polarisation measurements at sub-millimetre frequencies is discussed.
Krumer, Zachar; van Sark, Wilfried G. J. H. M.; de Mello Donegá, Celso; Schropp, Ruud E. I.
2013-09-01
Luminescent solar concentrators (LSCs) are low cost photovoltaic devices, which reduce the amount of necessary semiconductor material per unit area of a photovoltaic solar energy converter by means of concentration. The device is comprised of a thin plastic plate in which luminescent species (fluorophores) have been incorporated.The fluorophores absorb the solar light and radiatively re-emit a part of the energy. Total internal reflection traps most of the emitted light inside the plate and wave-guides it to a narrow side facet with a solar cell attached, where conversion into electricity occurs. The eciency of such devices is as yet rather low, due to several loss mechanisms, of which self-absorption is of high importance. Combined ray-tracing and Monte-Carlosimulations is a widely used tool for efficiency estimations of LSC-devices prior to manufacturing. We have applied this method to a model experiment, in which we analysed the impact of self-absorption onto LSC-efficiency of fluorophores with different absorption/emission-spectral overlap (Stokes-shift): several organic dyes and semiconductor quantum dots (single compound and core/shell of type-II). These results are compared with the ones obtained experimentally demonstrating a good agreement. The validated model is used to investigate systematically the influence of spectral separation and luminescence quantum efficiency on the intensity loss inconsequence of increased self-absorption. The results are used to adopt a quantity called the self-absorption cross-section and establish it as reliable criterion for self-absorption properties of materials that can be obtained from fundamental data and has a more universal scope of application, than the currently used Stokes-shift.
Configuring Product Modularity and Service Modularity for Mass Customization Strategies
Bask, Anu; Hsuan, Juliana; Rajahonka, Mervi
Service modularity is an emerging field of research, and there has been a growing interest on how it can contribute to service design and operations management. In this study we develop a framework to assess configurations of the bundling of products and services through modularization strategies......, and how such configurations become the foundations for mass customization strategies. As a result we identify critical characteristics that are relevant for both product and services, and suggest a conceptual framework consisting of twelve dynamic mass customization strategies with paired product...... and service modularity. Case examples are used for illustration of different strategies....
Configuring Product Modularity and Service Modularity for Mass Customization Strategies
Bask, Anu; Hsuan, Juliana; Rajahonka, Mervi
, and how such configurations become the foundations for mass customization strategies. As a result we identify critical characteristics that are relevant for both product and services, and suggest a conceptual framework consisting of twelve dynamic mass customization strategies with paired product......Service modularity is an emerging field of research, and there has been a growing interest on how it can contribute to service design and operations management. In this study we develop a framework to assess configurations of the bundling of products and services through modularization strategies...... and service modularity. Case examples are used for illustration of different strategies....
Collier, Scott; Yin, Xi
2016-01-01
We constrain the spectrum of two-dimensional unitary, compact conformal field theories with central charge c > 1 using modular bootstrap. Upper bounds on the gap in the dimension of primary operators of any spin, as well as in the dimension of scalar primaries, are computed numerically as functions of the central charge using semi-definite programming. Our bounds refine those of Hellerman and Friedan-Keller, and are in some cases saturated by known CFTs. In particular, we show that unitary CFTs with c < 8 must admit relevant deformations, and that a nontrivial bound on the gap of scalar primaries exists for c < 25. We also study bounds on the dimension gap in the presence of twist gaps, bounds on the degeneracy of operators, and demonstrate how "extremal spectra" which maximize the degeneracy at the gap can be determined numerically.
Modular small hydro configuration
1981-09-01
Smaller sites (those under 750 kilowatts) which previously were not attractive to develop using equipment intended for application at larger scale sites, were the focal point in the conception of a system which utilizes standard industrial components which are generally available within short procurement times. Such components were integrated into a development scheme for sites having 20 feet to 150 feet of head. The modular small hydro configuration maximizes the use of available components and minimizes modification of existing civil works. A key aspect of the development concept is the use of a vertical turbine multistage pump, used in the reverse mode as a hydraulic turbine. The configuration allows for automated operation and control of the hydroelectric facilities with sufficient flexibility for inclusion of potential hydroelectric sites into dispersed storage and generation (DSG) utility grid systems.
Modular reconfigurable machines incorporating modular open architecture control
Padayachee, J
2008-01-01
Full Text Available degrees of freedom on a single platform. A corresponding modular Open Architecture Control (OAC) system is presented. OAC overcomes the inflexibility of fixed proprietary automation, ensuring that MRMs provide the reconfigurability and extensibility...
RoboMusic with modular playware
Falkenberg, Kasper; Bærendsen, Niels Kristian; Nielsen, Jacob
2011-01-01
Based on the concepts of RoboMusic and modular playware, we developed a system composed of modular playware devices which allow any user to perform music in a simple, interactive manner. The key features exploited in the modular playware approach are modularity, fl exibility, construction...
RoboMusic with Modular Playware
Lund, Henrik Hautop; Bærendsen, Niels Kristian; Nielsen, Jacob
2010-01-01
Based on the concepts of RoboMusic and Modular Playware, we developed a system composed of modular playware devices, which allow any user to perform music in a simple, interactive manner. The key features exploited from the Modular Playware approach are modularity, flexibility, and construction...
Bi, Lei; Yang, Ping; Liu, Chao; Yi, Bingqi; Baum, Bryan A.; Van Diedenhoven, Bastiaan; Iwabuchi, Hironobu
2014-01-01
A fundamental problem in remote sensing and radiative transfer simulations involving ice clouds is the ability to compute accurate optical properties for individual ice particles. While relatively simple and intuitively appealing, the conventional geometric-optics method (CGOM) is used frequently for the solution of light scattering by ice crystals. Due to the approximations in the ray-tracing technique, the CGOM accuracy is not well quantified. The result is that the uncertainties are introduced that can impact many applications. Improvements in the Invariant Imbedding T-matrix method (II-TM) and the Improved Geometric-Optics Method (IGOM) provide a mechanism to assess the aforementioned uncertainties. The results computed by the II-TMþIGOM are considered as a benchmark because the IITM solves Maxwell's equations from first principles and is applicable to particle size parameters ranging into the domain at which the IGOM has reasonable accuracy. To assess the uncertainties with the CGOM in remote sensing and radiative transfer simulations, two independent optical property datasets of hexagonal columns are developed for sensitivity studies by using the CGOM and the II-TMþIGOM, respectively. Ice cloud bulk optical properties obtained from the two datasets are compared and subsequently applied to retrieve the optical thickness and effective diameter from Moderate Resolution Imaging Spectroradiometer (MODIS) measurements. Additionally, the bulk optical properties are tested in broadband radiative transfer (RT) simulations using the general circulation model (GCM) version of the Rapid Radiative Transfer Model (RRTMG) that is adopted in the National Center for Atmospheric Research (NCAR) Community Atmosphere Model (CAM, version 5.1). For MODIS retrievals, the mean bias of uncertainties of applying the CGOM in shortwave bands (0.86 and 2.13 micrometers) can be up to 5% in the optical thickness and as high as 20% in the effective diameter, depending on cloud optical
Forbang, R Teboh [John Hopkins University, Baltimore, MD (United States)
2014-06-01
Purpose: MultiPlan, the treatment planning system for the CyberKnife Robotic Radiosurgery system offers two approaches to dose computation, namely Ray-Tracing (RT), the default technique and Monte Carlo (MC), an option. RT is deterministic, however it accounts for primary heterogeneity only. MC on the other hand has an uncertainty associated with the calculation results. The advantage is that in addition, it accounts for heterogeneity effects on the scattered dose. Not all sites will benefit from MC. The goal of this work was to focus on central nervous system (CNS) tumors and compare dosimetrically, treatment plans computed with RT versus MC. Methods: Treatment plans were computed using both RT and MC for sites covering (a) the brain (b) C-spine (c) upper T-spine (d) lower T-spine (e) L-spine and (f) sacrum. RT was first used to compute clinically valid treatment plans. Then the same treatment parameters, monitor units, beam weights, etc., were used in the MC algorithm to compute the dose distribution. The plans were then compared for tumor coverage to illustrate the difference if any. All MC calculations were performed at a 1% uncertainty. Results: Using the RT technique, the tumor coverage for the brain, C-spine (C3–C7), upper T-spine (T4–T6), lower T-spine (T10), Lspine (L2) and sacrum were 96.8%, 93.1%, 97.2%, 87.3%, 91.1%, and 95.3%. The corresponding tumor coverage based on the MC approach was 98.2%, 95.3%, 87.55%, 88.2%, 92.5%, and 95.3%. It should be noted that the acceptable planning target coverage for our clinical practice is >95%. The coverage can be compromised for spine tumors to spare normal tissues such as the spinal cord. Conclusion: For treatment planning involving the CNS, RT and MC appear to be similar for most sites but for the T-spine area where most of the beams traverse lung tissue. In this case, MC is highly recommended.
MODULAR INNOVATION NETWORKS IN HIGH-TECHNOLOGY INDUSTRIES
Milton Freitas Chagas
2011-12-01
Full Text Available The article shows how interorganizational modular networks are structured in two high-tecnology industries: Embraer and Siemens. Three product platforms were used in the research: the Embraer 170/190 program from Embraer and the SX platform and X-ray equipment from Siemens. The objective of this article is to expand our comprehension of systems integration as a coordination mechanism in projects. The method adopted in the research is a case study. Data were collected by interviews and by analysis of documents from the two organizations. It was possible to identify and analyze the influence of the level of coupling and how the networks are structured. The research shows two levels of coupling in the modular innovation networks studied: two loosely coupled networks and one tightly coupled network. In addition, it was verified that the system integrators, the organizations that lead the modular networks, act as a matter of facts as knowledge integrators.
AES Modular Power Systems Project
National Aeronautics and Space Administration — The goals of this project are to 1) develop modular power design concepts for human exploration flight vehicles (longer-term) and assess, develop, and/or...
Hierarchy of Modular Graph Identities
D'Hoker, Eric
2016-01-01
The low energy expansion of Type II superstring amplitudes at genus one is organized in terms of modular graph functions associated with Feynman graphs of a conformal scalar field on the torus. In earlier work, surprising identities between two-loop graphs at all weights, and between higher-loop graphs of weights four and five were constructed. In the present paper, these results are generalized in two complementary directions. First, all identities at weight six and all dihedral identities at weight seven are obtained and proven. Whenever the Laurent polynomial at the cusp is available, the form of these identities confirms the pattern by which the vanishing of the Laurent polynomial governs the full modular identity. Second, the family of modular graph functions is extended to include all graphs with derivative couplings and worldsheet fermions. These extended families of modular graph functions are shown to obey a hierarchy of inhomogeneous Laplace eigenvalue equations. The eigenvalues are calculated analy...
Resilience of modular complex networks
Shai, Saray; Kenett, Yoed N; Faust, Miriam; Dobson, Simon; Havlin, Shlomo
2014-01-01
Complex networks often have a modular structure, where a number of tightly- connected groups of nodes (modules) have relatively few interconnections. Modularity had been shown to have an important effect on the evolution and stability of biological networks, on the scalability and efficiency of large-scale infrastructure, and the development of economic and social systems. An analytical framework for understanding modularity and its effects on network vulnerability is still missing. Through recent advances in the understanding of multilayer networks, however, it is now possible to develop a theoretical framework to systematically study this critical issue. Here we study, analytically and numerically, the resilience of modular networks under attacks on interconnected nodes, which exhibit high betweenness values and are often more exposed to failure. Our model provides new understandings into the feedback between structure and function in real world systems, and consequently has important implications as divers...
Habidite: viviendas modulares industrializadas
Gómez Jáuregui, V.
2009-03-01
Full Text Available This paper is an introduction to one of the most relevant constructive systems of the last years: The integral industrialized construction. This method, based on three-dimensional modules, produces buildings made mainly from spatial cells of big dimensions; these three-dimensional modules are fabricated entirely in factory and, once they are finished, they are carried out to the site, where they are assembled in an easy manner. Even though it’s not a totally new system (in fact, the precedents will also be mentioned in this essay, Habidite is very confident in backing this tendency and doing its part in order to obtain modular reinforced concrete buildings of extraordinary quality, with domotic implements totally integrated in the dwellings and a high degree of sustainability, eco-technology and energetic efficiency. Many advantages are exposed and explained, dealing with the optimization of the productive processes in construction by means of the most advanced technologies.En este artículo se realiza una breve introducción a uno de los sistemas constructivos que más auge está teniendo en los últimos años: la edificación industrializada integral. Realizado a base de módulos tridimensionales, es éste un método de construcción en el cual los edificios se conforman básicamente por medio de células espaciales de grandes dimensiones; estos módulos tridimensionales se elaboran íntegramente en fábrica y, una vez están totalmente terminados, se transportan a obra, donde son montados de forma sencilla y rápida. Aunque no es un sistema totalmente novedoso (de hecho sus antecedentes también serán tratados brevemente en este texto, Habidite apuesta fuertemente por esta tendencia y aporta su grano de arena para conseguir edificios modulares de hormigón armado de extraordinaria calidad, con implementos domóticos totalmente integrados en la vivienda y un alto grado de sostenibilidad, eco-tecnología y eficiencia energética. Se abordan
Enzymatic computation and cognitive modularity
Barrett, H. Clark
2005-01-01
Currently, there is widespread skepticism that higher cognitive processes, given their apparent flexibility and globality, could be carried out by specialized computational devices, or modules. This skepticism is largely due to Fodor's influential definition of modularity. From the rather flexible catalogue of possible modular features that Fodor originally proposed has emerged a widely held notion of modules as rigid, informationally encapsulated devices that accept highly local inputs and w...
Spacecraft Modularity for Serviceable Satellites
Rossetti, Dino; Keer, Beth; Panek, John; Reed, Benjamin; Cepollina, Frank; Ritter, Robert
2015-01-01
Satellite servicing has been a proven capability of NASA since the first servicing missions in the 1980s with astronauts on the space shuttle. This capability enabled the on-orbit assembly of the International Space Station (ISS) and saved the Hubble Space Telescope (HST) mission following the discovery of the flawed primary mirror. The effectiveness and scope of servicing opportunities, especially using robotic servicers, is a function of how cooperative a spacecraft is. In this paper, modularity will be presented as a critical design aspect for a spacecraft that is cooperative from a servicing perspective. Different features of modularity are discussed using examples from HST and the Multimission Modular Spacecraft (MMS) program from the 1980s and 1990s. The benefits of modularity will be presented including those directly related to servicing and those outside of servicing including reduced costs and increased flexibility. The new Reconfigurable Operational spacecraft for Science and Exploration (ROSE) concept is introduced as an affordable implementation of modularity that provides cost savings and flexibility. Key aspects of the ROSE architecture are discussed such as the module design and the distributed avionics architecture. The ROSE concept builds on the experience from MMS and due to its modularity, would be highly suitable as a future client for on-orbit servicing.
Modular Isotopic Thermoelectric Generator
Schock, Alfred
1981-04-03
Advanced RTG concepts utilizing improved thermoelectric materials and converter concepts are under study at Fairchild for DOE. The design described here is based on DOE's newly developed radioisotope heat source, and on an improved silicon-germanium material and a multicouple converter module under development at Syncal. Fairchild's assignment was to combine the above into an attractive power system for use in space, and to assess the specific power and other attributes of that design. The resultant design is highly modular, consisting of standard RTG slices, each producing ~24 watts at the desired output voltage of 28 volt. Thus, the design could be adapted to various space missions over a wide range of power levels, with little or no redesign. Each RTG slice consists of a 250-watt heat source module, eight multicouple thermoelectric modules, and standard sections of insulator, housing, radiator fins, and electrical circuit. The design makes it possible to check each thermoelectric module for electrical performance, thermal contact, leaktightness, and performance stability, after the generator is fully assembled; and to replace any deficient modules without disassembling the generator or perturbing the others. The RTG end sections provide the spring-loaded supports required to hold the free-standing heat source stack together during launch vibration. Details analysis indicates that the design offers a substantial improvement in specific power over the present generator of RTGs, using the same heat source modules. There are three copies in the file.
Modular Nuclear Testing Concept
Wouters, L. F.
1964-07-01
The continuing concern with efficient utilization of manpower at the Nevada Test Site (NTS) and the seemingly high cost of individual nuclear shots, together with the recent evolution of the L-12 scope, generated some fresh thoughts concerning more efficient procedures for the `average` test. Every time anyone looks at the problem., they tend to analyze the existing conventional approach and try to find the one or two most expensive and `lossy` factors in the can of worms. Usually this turns out to be a problem within the realm of specialization of the particular analyst! People not so directly concerned with the program tend to look for, or wish for, or even `invent` miracles`. Our present techniques appear to be the sum (and possibly even the product) of many small contributions which have all been beaten down to the same level of importance. Such a situation in any systemic problem is usually symptomatic of the need for fairly violent departures in the aver-all system approach, at least in thinking. This report proposes and details a modular nuclear testing concept.
Modular Approach to Spintronics.
Camsari, Kerem Yunus; Ganguly, Samiran; Datta, Supriyo
2015-06-11
There has been enormous progress in the last two decades, effectively combining spintronics and magnetics into a powerful force that is shaping the field of memory devices. New materials and phenomena continue to be discovered at an impressive rate, providing an ever-increasing set of building blocks that could be exploited in designing transistor-like functional devices of the future. The objective of this paper is to provide a quantitative foundation for this building block approach, so that new discoveries can be integrated into functional device concepts, quickly analyzed and critically evaluated. Through careful benchmarking against available theory and experiment we establish a set of elemental modules representing diverse materials and phenomena. These elemental modules can be integrated seamlessly to model composite devices involving both spintronic and nanomagnetic phenomena. We envision the library of modules to evolve both by incorporating new modules and by improving existing modules as the field progresses. The primary contribution of this paper is to establish the ground rules or protocols for a modular approach that can build a lasting bridge between materials scientists and circuit designers in the field of spintronics and nanomagnetics.
Lectures on Hilbert modular varieties and modular forms
Goren, Eyal Z
2001-01-01
This book is devoted to certain aspects of the theory of p-adic Hilbert modular forms and moduli spaces of abelian varieties with real multiplication. The theory of p-adic modular forms is presented first in the elliptic case, introducing the reader to key ideas of N. M. Katz and J.-P. Serre. It is re-interpreted from a geometric point of view, which is developed to present the rudiments of a similar theory for Hilbert modular forms. The theory of moduli spaces of abelian varieties with real multiplication is presented first very explicitly over the complex numbers. Aspects of the general theory are then exposed, in particular, local deformation theory of abelian varieties in positive characteristic. The arithmetic of p-adic Hilbert modular forms and the geometry of moduli spaces of abelian varieties are related. This relation is used to study q-expansions of Hilbert modular forms, on the one hand, and stratifications of moduli spaces on the other hand. The book is addressed to graduate students and non-exper...
Modular framization of the BMW algebra
Juyumaya, Jesus
2010-01-01
In this work we introduce the concept of Modular Framization or simply Framization. We construct a framization $F_{d,n}$ of the Birman--Wenzl--Murakami algebra, also known as BMW algebra, and start a systematic study of this framization. We show that $F_{d,n}$ is finite dimensional and the \\lq braid generators\\rq\\ of this algebra satisfy a quartic relation which is of minimal degree not containing the generators $t_i$. They also satisfy a quintic relation, as the smallest closed relation. We conjecture that the algebras $F_{d,n}$ support a Markov trace which allow to define polynomial invariants for unoriented knots in an analogous way that the Kauffman polynomial is derived from the BMW algebra. The idea originates from the Yokonuma--Hecke algebra, built from the classical Hecke algebra by adding framing generators and changing the Hecke algebra quadratic relation by a new quadratic relation which involves the framing generators. Using the Yokonuma--Hecke algebras and a Markov trace constructed on them\\cite{...
Modular Stirling Radioisotope Generator
Schmitz, Paul C.; Mason, Lee S.; Schifer, Nicholas A.
2016-01-01
High-efficiency radioisotope power generators will play an important role in future NASA space exploration missions. Stirling Radioisotope Generators (SRGs) have been identified as a candidate generator technology capable of providing mission designers with an efficient, high-specific-power electrical generator. SRGs high conversion efficiency has the potential to extend the limited Pu-238 supply when compared with current Radioisotope Thermoelectric Generators (RTGs). Due to budgetary constraints, the Advanced Stirling Radioisotope Generator (ASRG) was canceled in the fall of 2013. Over the past year a joint study by NASA and the Department of Energy (DOE) called the Nuclear Power Assessment Study (NPAS) recommended that Stirling technologies continue to be explored. During the mission studies of the NPAS, spare SRGs were sometimes required to meet mission power system reliability requirements. This led to an additional mass penalty and increased isotope consumption levied on certain SRG-based missions. In an attempt to remove the spare power system, a new generator architecture is considered, which could increase the reliability of a Stirling generator and provide a more fault-tolerant power system. This new generator called the Modular Stirling Radioisotope Generator (MSRG) employs multiple parallel Stirling convertor/controller strings, all of which share the heat from the General Purpose Heat Source (GPHS) modules. For this design, generators utilizing one to eight GPHS modules were analyzed, which provided about 50 to 450 W of direct current (DC) to the spacecraft, respectively. Four Stirling convertors are arranged around each GPHS module resulting in from 4 to 32 Stirling/controller strings. The convertors are balanced either individually or in pairs, and are radiatively coupled to the GPHS modules. Heat is rejected through the housing/radiator, which is similar in construction to the ASRG. Mass and power analysis for these systems indicate that specific
The non-semisimple Verlinde formula and pseudo-trace functions
Gainutdinov, A M
2016-01-01
We point out that results of Shimizu on internal characters imply a useful non-semisimple variant of the categorical Verlinde formula for factorisable finite tensor categories. When combined with results on pseudo-trace functions by Miyamoto and Arike-Nagatomo, one can make a precise conjecture for a non-semisimple modular Verlinde formula which relates modular properties of pseudo-trace functions and the product in the Grothendieck ring of the corresponding vertex operator algebra.
Trofimov, M. Yu.; Zakharenko, A. D.; Kozitskiy, S. B.
2016-10-01
A mode parabolic equation in the ray centered coordinates for 3D underwater sound propagation is developed. The Gaussian beam tracing in this case is constructed. The test calculations are carried out for the ASA wedge benchmark and proved an excellent agreement with the source images method in the case of cross-slope propagation. But in the cases of wave propagation at some angles to the cross-slope direction an account of mode interaction becomes necessary.
Modular Power Standard for Space Explorations Missions
Oeftering, Richard C.; Gardner, Brent G.
2016-01-01
Future human space exploration will most likely be composed of assemblies of multiple modular spacecraft elements with interconnected electrical power systems. An electrical system composed of a standardized set modular building blocks provides significant development, integration, and operational cost advantages. The modular approach can also provide the flexibility to configure power systems to meet the mission needs. A primary goal of the Advanced Exploration Systems (AES) Modular Power System (AMPS) project is to establish a Modular Power Standard that is needed to realize these benefits. This paper is intended to give the space exploration community a "first look" at the evolving Modular Power Standard and invite their comments and technical contributions.
Quantum modularity and complex Chern-Simons theory
Dimofte, Tudor
2015-01-01
The Quantum Modularity Conjecture of Zagier predicts the existence of a formal power series with arithmetically interesting coefficients that appears in the asymptotics of the Kashaev invariant at each root of unity. Our goal is to construct a power series from a Neumann-Zagier datum (i.e., an ideal triangulation of the knot complement and a geometric solution to the gluing equations) and a complex root of unity $\\zeta$. We prove that the coefficients of our series lie in the trace field of the knot, adjoined a complex root of unity. We conjecture that our series are those that appear in the Quantum Modularity Conjecture and confirm that they match the numerical asymptotics of the Kashaev invariant (at various roots of unity) computed by Zagier and the first author. Our construction is motivated by the analysis of singular limits in Chern-Simons theory with gauge group $SL(2,C)$ at fixed level $k$, where $\\zeta^k=1$.
Imani, Sahar Sadat Afshar
2013-01-01
Modular EFL Educational Program has managed to offer specialized language education in two specific fields: Audio-visual Materials Translation and Translation of Deeds and Documents. However, no explicit empirical studies can be traced on both internal and external validity measures as well as the extent of compatibility of both courses with the…
Cozer, Thamara C.; Conceicao, Andre L.C.; Paschuk, Sergei A.; Rocha, Anna S.S. da; Fagundes, Alana C.F.; Maciel, Karla F.R.; Pimentel, Gustavo R.O.; Badelli, Juliana C., E-mail: thamara.cozer@gmail.com, E-mail: alconceicao@utfpr.edu.br, E-mail: sergei@utfpr.edu.br, E-mail: anna@utfpr.edu.br, E-mail: alanacarolinef@gmail.com, E-mail: karla_rimanski@hotmail.com, E-mail: g_rop@hotmail.com, E-mail: jubadellin@gmail.com [Universidade Tecnologica Federal do Parana (UTFPR), Curitiba, PR (Brazil). Lab. de Espectroscopia de Raio-X
2015-07-01
Studies performed with canines indicate that one of the main neoplasia which affect these animals are the breast tumors, representing from 25% to 50% of all kinds of tumors. Moreover, half of them are classified as malignant. In this sense, recent researches on humans have been associated the presence of certain trace elements with the development of breast neoplasia in those individuals. Then, as the breast tissue composition in canines is very similar to the humans, it is expected the same behavior. In this direction, a very effective technique to identify and to determinate trace elements concentration is the EDXRF. However, studies on this area are scarce in the literature. Therefore, in this work it was developed an approach to quantify the main trace elements present into these tumors with high sensitivity. For this purpose, it was determined calibration curves of standards samples diluted in water, with concentrations of Ca, Fe, Cu and Zn, ranging from 400mg/kg to 35mg/kg, from 20mg/kg to 2mg/kg, from 10mg/kg to 1mg/kg and from 100mg/kg to 10mg/kg, respectively. All calibration curves were linearly fitted and on basis in this behavior it was determined the sensitivity of our approach to quantify the concentration of the trace elements mentioned above. In addition, it is important to mention that studies in this area are of great potential, because EDXRF represents a quickly practical and non-destructive alternative to quantify trace elements. (author)
Product Modular Design Incorporating Preventive Maintenance Issues
GAO Yicong; FENG Yixiong; TAN Jianrong
2016-01-01
Traditional modular design methods lead to product maintenance problems, because the module form of a system is created according to either the function requirements or the manufacturing considerations. For solving these problems, a new modular design method is proposed with the considerations of not only the traditional function related attributes, but also the maintenance related ones. First, modularity parameters and modularity scenarios for product modularity are defined. Then the reliability and economic assessment models of product modularity strategies are formulated with the introduction of the effective working age of modules. A mathematical model used to evaluate the difference among the modules of the product so that the optimal module of the product can be established. After that, a multi-objective optimization problem based on metrics for preventive maintenance interval different degrees and preventive maintenance economics is formulated for modular optimization. Multi-objective GA is utilized to rapidly approximate the Pareto set of optimal modularity strategy trade-offs between preventive maintenance cost and preventive maintenance interval difference degree. Finally, a coordinate CNC boring machine is adopted to depict the process of product modularity. In addition, two factorial design experiments based on the modularity parameters are constructed and analyzed. These experiments investigate the impacts of these parameters on the optimal modularity strategies and the structure of module. The research proposes a new modular design method, which may help to improve the maintainability of product in modular design.
Product modular design incorporating preventive maintenance issues
Gao, Yicong; Feng, Yixiong; Tan, Jianrong
2016-03-01
Traditional modular design methods lead to product maintenance problems, because the module form of a system is created according to either the function requirements or the manufacturing considerations. For solving these problems, a new modular design method is proposed with the considerations of not only the traditional function related attributes, but also the maintenance related ones. First, modularity parameters and modularity scenarios for product modularity are defined. Then the reliability and economic assessment models of product modularity strategies are formulated with the introduction of the effective working age of modules. A mathematical model used to evaluate the difference among the modules of the product so that the optimal module of the product can be established. After that, a multi-objective optimization problem based on metrics for preventive maintenance interval different degrees and preventive maintenance economics is formulated for modular optimization. Multi-objective GA is utilized to rapidly approximate the Pareto set of optimal modularity strategy trade-offs between preventive maintenance cost and preventive maintenance interval difference degree. Finally, a coordinate CNC boring machine is adopted to depict the process of product modularity. In addition, two factorial design experiments based on the modularity parameters are constructed and analyzed. These experiments investigate the impacts of these parameters on the optimal modularity strategies and the structure of module. The research proposes a new modular design method, which may help to improve the maintainability of product in modular design.
Modular robotics for playful physiotherapy
Lund, Henrik Hautop
2009-01-01
We developed modular robotic tiles to be used for playful physiotherapy, which is supposed to motivate patients to engage in and perform physical rehabilitation exercises. We tested the modular robotic tiles for an extensive period of time (3 years) in daily use in a hospital rehabilitation unit e.......g. for cardiac patients. Also, the tiles were tested for performing physical rehabilitation of stroke patients in their private home. In all pilot test cases qualitative feedback indicate that the patients find the playful use of modular robotic tiles engaging and motivating for them to perform...... the rehabilitation. Also, initial pilot test data suggest that some playful exercises on the tiles demand an average heart rate of 75% and 86% of the maximum heart rate....
Modular Software-Defined Radio
Rhiemeier Arnd-Ragnar
2005-01-01
Full Text Available In view of the technical and commercial boundary conditions for software-defined radio (SDR, it is suggestive to reconsider the concept anew from an unconventional point of view. The organizational principles of signal processing (rather than the signal processing algorithms themselves are the main focus of this work on modular software-defined radio. Modularity and flexibility are just two key characteristics of the SDR environment which extend smoothly into the modeling of hardware and software. In particular, the proposed model of signal processing software includes irregular, connected, directed, acyclic graphs with random node weights and random edges. Several approaches for mapping such software to a given hardware are discussed. Taking into account previous findings as well as new results from system simulations presented here, the paper finally concludes with the utility of pipelining as a general design guideline for modular software-defined radio.
Modular process modeling for OPC
Keck, M. C.; Bodendorf, C.; Schmidtling, T.; Schlief, R.; Wildfeuer, R.; Zumpe, S.; Niehoff, M.
2007-03-01
Modular OPC modeling, describing mask, optics, resist and etch processes separately is an approach to keep efforts for OPC manageable. By exchanging single modules of a modular OPC model, a fast response to process changes during process development is possible. At the same time efforts can be reduced, since only single modular process steps have to be re-characterized as input for OPC modeling as the process is adjusted and optimized. Commercially available OPC tools for full chip processing typically make use of semi-empirical models. The goal of our work is to investigate to what extent these OPC tools can be applied for modeling of single process steps as separate modules. For an advanced gate level process we analyze the modeling accuracy over different process conditions (focus and dose) when combining models for each process step - optics, resist and etch - for differing single processes to a model describing the total process.
Modular system design and evaluation
Levin, Mark Sh
2015-01-01
This book examines seven key combinatorial engineering frameworks (composite schemes consisting of algorithms and/or interactive procedures) for hierarchical modular (composite) systems. These frameworks are based on combinatorial optimization problems (e.g., knapsack problem, multiple choice problem, assignment problem, morphological clique problem), with the author’s version of morphological design approach – Hierarchical Morphological Multicritieria Design (HMMD) – providing a conceptual lens with which to elucidate the examples discussed. This approach is based on ordinal estimates of design alternatives for systems parts/components, however, the book also puts forward an original version of HMMD that is based on new interval multiset estimates for the design alternatives with special attention paid to the aggregation of modular solutions (system versions). The second part of ‘Modular System Design and Evaluation’ provides ten information technology case studies that enriches understanding of th...
Emergent interfaces for feature modularization
Ribeiro, Márcio; Brabrand, Claus
2014-01-01
Developers frequently introduce errors into software systems when they fail to recognise module dependencies. Using forty-three software families and Software Product Lines (SPLs), where the majority are commonly used in industrial practice, the authors reports on the feature modularization problem and provides a study of how often it may occur in practice. To solve the problem they present the concept of emergent feature modularization which aims to establish contracts between features to prevent developers from breaking other features when performing a maintenance task.
短波射线追踪技术中的电离层混合建模方法%Ionosphere hybrid modeling method for short-wave ray tracing
栗伟珉; 苏东林; 阎照文; 刘焱
2012-01-01
在国际参考电离层模型和多层准抛物模型的基础上,提出了一种混合应用两种模型进行电离层建模的新方法.利用射线追踪技术,分别对混合模型和传统国际参考电离层模型下短波射线在电离层中的轨迹进行了仿真,得到了电波群路径.通过与实测电波群路径的对比,结果表明：对中国中纬度地区在电离层混合模型下的射线追踪精度优于传统国际参考电离层模型下的射线追踪精度,同时混合建模方法降低了多层准抛物模型对输入条件的要求,扩展了多层准抛物模型在射线追踪技术中的应用范围.%Based on the international reference ionosphere（IRI） and the quasi-parabolic segments（QPS） model,a new ionosphere hybrid modeling method for short-wave ray tracing was proposed.The group ranges which show the short-wave propagation trace in the ionosphere were obtained separately by simulation in the hybrid model and the IRI model.By comparing the simulated results and the ionospheric oblique incidence sounding experimental data,the hybrid modeling method accuracy at mid-latitude region in China was analyzed.It indicates the ray tracing simulation accuracy in the hybrid model on experimental day better than the one in the IRI model.The limit to the QPS model＇s input is reduced by the hybrid modeling method and the QPS model＇s application range is extended in ray tracing technology.
Walk modularity and community structure in networks
Mehrle, David; Harkin, Anthony
2014-01-01
Modularity maximization has been one of the most widely used approaches in the last decade for discovering community structure in networks of practical interest in biology, computing, social science, statistical mechanics, and more. Modularity is a quality function that measures the difference between the number of edges found within clusters minus the number of edges one would statistically expect to find based on random chance. We present a natural generalization of modularity based on the difference between the actual and expected number of walks within clusters, which we call walk-modularity. Walk-modularity can be expressed in matrix form, and community detection can be performed by finding leading eigenvectors of the walk-modularity matrix. We demonstrate community detection on both synthetic and real-world networks and find that walk-modularity maximization returns significantly improved results compared to traditional modularity maximization.
Modularity for Modulating Exercises and Levels
Lund, Henrik Hautop; Nielsen, Camilla Balslev
2011-01-01
The modular interactive tiles aim at engaging anybody (elderly, carer, hospital personnel, children) in performing playful and motivating physical activities. Inspired by modular robotics, each tile is a self-contained module with processing power and communication to neighbouring modules...
Un-Hong Wong
2014-01-01
Full Text Available In this paper, we model the reflectance of the lunar regolith by a new method combining Monte Carlo ray tracing and Hapke’s model. The existing modeling methods exploit either a radiative transfer model or a geometric optical model. However, the measured data from an Interference Imaging spectrometer (IIM on an orbiter were affected not only by the composition of minerals but also by the environmental factors. These factors cannot be well addressed by a single model alone. Our method implemented Monte Carlo ray tracing for simulating the large-scale effects such as the reflection of topography of the lunar soil and Hapke’s model for calculating the reflection intensity of the internal scattering effects of particles of the lunar soil. Therefore, both the large-scale and microscale effects are considered in our method, providing a more accurate modeling of the reflectance of the lunar regolith. Simulation results using the Lunar Soil Characterization Consortium (LSCC data and Chang’E-1 elevation map show that our method is effective and useful. We have also applied our method to Chang’E-1 IIM data for removing the influence of lunar topography to the reflectance of the lunar soil and to generate more realistic visualizations of the lunar surface.
van der Horst, A J; Miller-Jones, J C A; Linford, J D; Gorosabel, J; Russell, D M; Postigo, A de Ugarte; Lundgren, A A; Taylor, G B; Maitra, D; Guziy, S; Belloni, T M; Kouveliotou, C; Jonker, P G; Kamble, A; Paragi, Z; Homan, J; Kuulkers, E; Granot, J; Altamirano, D; Buxton, M M; Castro-Tirado, A; Fender, R P; Garrett, M A; Gehrels, N; Hartmann, D H; Kennea, J A; Krimm, H A; Mangano, V; Ramirez-Ruiz, E; Romano, P; Wijers, R A M J; Wijnands, R; Yang, Y J
2013-01-01
MAXI J1659-152 was discovered on 2010 September 25 as a new X-ray transient, initially identified as a gamma-ray burst, but was later shown to be a new X-ray binary with a black hole as the most likely compact object. Dips in the X-ray light curves have revealed that MAXI J1659-152 is the shortest period black hole candidate identified to date. Here we present the results of a large observing campaign at radio, sub-millimeter, near-infrared (nIR), optical and ultraviolet (UV) wavelengths. We have combined this very rich data set with the available X-ray observations to compile a broadband picture of the evolution of this outburst. We have performed broadband spectral modeling, demonstrating the presence of a spectral break at radio frequencies and a relationship between the radio spectrum and X-ray states. Also, we have determined physical parameters of the accretion disk and put them into context with respect to the other parameters of the binary system. Finally, we have investigated the radio-X-ray and nIR/...
Cheney, James; Ahmed, Amal
2008-01-01
Provenance is information about the origin, derivation, ownership, or history of an object. It has recently been studied extensively in scientific databases and other settings due to its importance in helping scientists judge data validity, quality and integrity. However, most models of provenance have been stated as ad hoc definitions motivated by informal concepts such as "comes from", "influences", "produces", or "depends on". These models lack clear formalizations describing in what sense the definitions capture these intuitive concepts. This makes it difficult to compare approaches, evaluate their effectiveness, or argue about their validity. We introduce provenance traces, a general form of provenance for the nested relational calculus (NRC), a core database query language. Provenance traces can be thought of as concrete data structures representing the operational semantics derivation of a computation; they are related to the traces that have been used in self-adjusting computation, but differ in impor...
p-adic Modular Symbols and Λ-adic Modular Forms
Fu Zheng WANG
2006-01-01
A construction of Λ-adic modular forms from p-adic modular symbols is described. It showsthat each Λ linear map satisfying some certain conditions from the module of p-adic modular symbols to Λ corresponds to a Λ-adic modular form.
Additive Approximation Algorithms for Modularity Maximization
Kawase, Yasushi; Matsui, Tomomi; Miyauchi, Atsushi
2016-01-01
The modularity is a quality function in community detection, which was introduced by Newman and Girvan (2004). Community detection in graphs is now often conducted through modularity maximization: given an undirected graph $G=(V,E)$, we are asked to find a partition $\\mathcal{C}$ of $V$ that maximizes the modularity. Although numerous algorithms have been developed to date, most of them have no theoretical approximation guarantee. Recently, to overcome this issue, the design of modularity max...
A Modular Rewriting Semantics for CML
Chalub, Fabricio; Braga, Christiano de Oliveira
2004-01-01
This paper presents a modular rewriting semantics (MRS) specification for Reppy's Concurrent ML (CML), based on Peter Mosses' modular structural operational semantics specification for CML. A modular rewriting semantics specification for a programming language is a rewrite theory in rewriting log...
Generating graphs that approach a prescribed modularity
Trajanovski, S.; Kuipers, F.A.; Martín-Hernández, J.; Van Mieghem, P.
2013-01-01
Modularity is a quantitative measure for characterizing the existence of a community structure in a network. A network's modularity depends on the chosen partitioning of the network into communities, which makes finding the specific partition that leads to the maximum modularity a hard problem. In t
SOME RESULTS OF MODULAR LIE SUPERALGEBRAS
无
2006-01-01
In the present article, the authors give some properties on subinvariant subalgebras of modular Lie superalgebras and obtain the derivation tower theorem of modular Lie superalgebras, which is analogous to the automorphism tower theorem of finite groups.Moreover, they announce and prove some results of modular complete Lie superalgebras.
On modular Galois representations modulo prime powers
Chen, Imin; Kiming, Ian; Wiese, Gabor
2013-01-01
We study modular Galois representations mod pm. We show that there are three progressively weaker notions of modularity for a Galois representation mod pm: We have named these "strongly", "weakly", and "dc-weakly" modular. Here, "dc" stands for "divided congruence" in the sense of Katz and Hida. ...
On modular Galois representations modulo prime powers
Chen, Imin; Kiming, Ian; Wiese, Gabor
2013-01-01
. These notions of modularity are relative to a fixed level M. Using results of Hida we display a level-lowering result ("stripping-of-powers of p away from the level"): A mod pm strongly modular representation of some level Npr is always dc-weakly modular of level N (here, N is a natural number not divisible...
Hierarchy of modular graph identities
D’Hoker, Eric; Kaidi, Justin [Mani L. Bhaumik Institute for Theoretical Physics, Department of Physics and Astronomy,University of California,Los Angeles, CA 90095 (United States)
2016-11-09
The low energy expansion of Type II superstring amplitudes at genus one is organized in terms of modular graph functions associated with Feynman graphs of a conformal scalar field on the torus. In earlier work, surprising identities between two-loop graphs at all weights, and between higher-loop graphs of weights four and five were constructed. In the present paper, these results are generalized in two complementary directions. First, all identities at weight six and all dihedral identities at weight seven are obtained and proven. Whenever the Laurent polynomial at the cusp is available, the form of these identities confirms the pattern by which the vanishing of the Laurent polynomial governs the full modular identity. Second, the family of modular graph functions is extended to include all graphs with derivative couplings and worldsheet fermions. These extended families of modular graph functions are shown to obey a hierarchy of inhomogeneous Laplace eigenvalue equations. The eigenvalues are calculated analytically for the simplest infinite sub-families and obtained by Maple for successively more complicated sub-families. The spectrum is shown to consist solely of eigenvalues s(s−1) for positive integers s bounded by the weight, with multiplicities which exhibit rich representation-theoretic patterns.
Modular crystals as modulated structures
Elcoro, L.; Perez-Mato, J.M.; Friese, K.;
2008-01-01
The use of the superspace formalism is extended to the description and refinement of the homologous series of modular structures with two symmetry-related modules with different orientations. The lillianite homologous series has been taken as a study case. Starting from a commensurate modulated c...
Physical Modeling Modular Boxes: PHOXES
Gelineck, Steven; Serafin, Stefania
2010-01-01
This paper presents the development of a set of musical instruments, which are based on known physical modeling sound synthesis techniques. The instruments are modular, meaning that they can be combined in various ways. This makes it possible to experiment with physical interaction and sonic expl...
Modularity in Cancer Care Provision
Gobbi, Chiara; Hsuan, Juliana
2012-01-01
The paper presents the findings of a case study research conducted within the Danish healthcare system aimed at analyzing how modularity is deployed in the process of delivery cancer care. Three cancer packages are presented into detailed describing the process of defining the diagnosis and treat...
Pell Numbers, Pell-Lucas Numbers and Modular Group
Q. Mushtaq; U. Hayat
2007-01-01
We show that the matrix A(g), representing the element g = ((xy)2(xy2)2)m (m≥) of the modular group PSL(2,Z)=(x,y:x2=y3=1),where x:z →-1/z and y :z → -1/z, is a 2×2 symmetric matrix whose entries are Pell numbers and whose trace is a Pell-Lucas number. If g fixes elements of Q(√d), where d is a square-free positive number, on the circuit of the coset diagram, then d ＝ 2 and there are only four pairs of ambiguous numbers on the circuit.
基于GPU和均匀栅格法的光线追踪算法研究%Research of ray-tracing algorithm based on GPU and uniform grid method
童星; 袁道华
2011-01-01
由于GPU(图形处理器)性能的大幅提高和可编程性的发展,基于GPU的光线追踪算法逐渐成为研究热点,光线追踪算法需要的计算量大,基于此,分析了光线追踪算法的基本原理,在NVIDIA公司的CUDA(计算统一设备体系结构)环境下采用均匀栅格法作为加速结构实现了光线追踪算法.实验结果表明,该计算模式相对于传统基于CPU的光线追踪算法具有更快的整体运算速度,GPU适合处理高密度数据计算.%Ray-tracing is the technique that rendering images from a three dimensional model of a scene by projecting it on to a two dimensional image plane. In the past decades, the development of the computer graphic (especial for raster graphics systems) emphasize on building the high-efficient, low-cost large graphic systems. For the above-mentioned reasons such as the implementation of a large number of mathematical calculation, the large-scale parallel processing technologies play a important role in graphics compose. The principle of ray-tracing algorithm is introduced. A ray-tracing parallel processing model is built through the research on GPU stream processing and MPICH, and it is proved that applying this mode reduces computation time effectively and the quality of the generated graph holds no difference with that by traditional stand-alone computer.
Burns, Jack O.; Datta, Abhirup; Hallman, Eric J.
2016-06-01
Galaxy clusters are assembled through large and small mergers which are the most energetic events ("bangs") since the Big Bang. Cluster mergers "stir" the intracluster medium (ICM) creating shocks and turbulence which are illuminated by ~Mpc-sized radio features called relics and halos. These shocks heat the ICM and are detected in x-rays via thermal emission. Disturbed morphologies in x-ray surface brightness and temperatures are direct evidence for cluster mergers. In the radio, relics (in the outskirts of the clusters) and halos (located near the cluster core) are also clear signposts of recent mergers. Our recent ENZO cosmological simulations suggest that around a merger event, radio emission peaks very sharply (and briefly) while the x-ray emission rises and decays slowly. Hence, a sample of galaxy clusters that shows both luminous x-ray emission and radio relics/halos are good candidates for very recent mergers. We are in the early stages of analyzing a unique sample of 48 galaxy clusters with (i) known radio relics and/or halos and (ii) significant archival x-ray observations (>50 ksec) from Chandra and/or XMM. We have developed a new x-ray data analysis pipeline, implemented on parallel processor supercomputers, to create x-ray surface brightness, high fidelity temperature, and pressure maps of these clusters in order to study merging activity. The temperature maps are made using three different map-making techniques: Weighted Voronoi Tessellation, Adaptive Circular Binning, and Contour Binning. In this talk, we will show preliminary results for several clusters, including Abell 2744 and the Bullet cluster. This work is supported by NASA ADAP grant NNX15AE17G.
Bundling Products and Services Through Modularization Strategies
Bask, Anu; Hsuan, Juliana; Rajahonka, Mervi;
2012-01-01
Modularity has been recognized as a powerful tool in improving the efficiency and management of product design and manufacturing. However, the integrated view on covering both, product and service modularity for product-service systems (PSS), is under researched. Therefore, in this paper our...... objective is to contribute to the PSS modularity. Thus, we describe configurations of PSSs and the bundling of products and services through modularization strategies. So far there have not been tools to analyze and determine the correct combinations of degrees of product and service modularities....
Towards a Standard for Modular Petri Nets
Kindler, Ekkart; Petrucci, Laure
2009-01-01
as a mechanism for modules in Petri nets that is independent from a particular version of Petri nets and that can mimic many composition mechanisms by a simple import and export concept. Due to its generality, the semantics of modular PNML was only informally defined. Moreover, modular PNML did not define which...... concepts could or should be subject to import and export in high-level Petri nets. In this paper, we formalise a minimal version of modular high-level Petri nets, which is based on the concepts of modular PNML. This shows that modular PNML can be formalised once a specific version of Petri net is fixed...
Reflective modular forms in algebraic geometry
Gritsenko, Valery
2010-01-01
We prove that the existence of a strongly reflective modular form of a large weight implies that the Kodaira dimension of the corresponding modular variety is negative or, in some special case, it is equal to zero. Using the Jacobi lifting we construct three towers of strongly reflective modular forms with the simplest possible divisor. In particular we obtain a Jacobi lifting construction of the Borcherds-Enriques modular form Phi_4 and Jacobi liftings of automorphic discriminants of the K\\"ahler moduli of Del Pezzo surfaces constructed recently by Yoshikawa. We obtain also three modular varieties of dimension 4, 6 and 7 of Kodaira dimension 0.
Modularity and stability in ecological communities
Grilli, Jacopo; Rogers, Tim; Allesina, Stefano
2016-01-01
Networks composed of distinct, densely connected subsystems are called modular. In ecology, it has been posited that a modular organization of species interactions would benefit the dynamical stability of communities, even though evidence supporting this hypothesis is mixed. Here we study the effect of modularity on the local stability of ecological dynamical systems, by presenting new results in random matrix theory, which are obtained using a quaternionic parameterization of the cavity method. Results show that modularity can have moderate stabilizing effects for particular parameter choices, while anti-modularity can greatly destabilize ecological networks. PMID:27337386
Quasispecies theory for evolution of modularity.
Park, Jeong-Man; Niestemski, Liang Ren; Deem, Michael W
2015-01-01
Biological systems are modular, and this modularity evolves over time and in different environments. A number of observations have been made of increased modularity in biological systems under increased environmental pressure. We here develop a quasispecies theory for the dynamics of modularity in populations of these systems. We show how the steady-state fitness in a randomly changing environment can be computed. We derive a fluctuation dissipation relation for the rate of change of modularity and use it to derive a relationship between rate of environmental changes and rate of growth of modularity. We also find a principle of least action for the evolved modularity at steady state. Finally, we compare our predictions to simulations of protein evolution and find them to be consistent.
Quasispecies theory for evolution of modularity
Park, Jeong-Man; Niestemski, Liang Ren; Deem, Michael W.
2015-01-01
Biological systems are modular, and this modularity evolves over time and in different environments. A number of observations have been made of increased modularity in biological systems under increased environmental pressure. We here develop a quasispecies theory for the dynamics of modularity in populations of these systems. We show how the steady-state fitness in a randomly changing environment can be computed. We derive a fluctuation dissipation relation for the rate of change of modularity and use it to derive a relationship between rate of environmental changes and rate of growth of modularity. We also find a principle of least action for the evolved modularity at steady state. Finally, we compare our predictions to simulations of protein evolution and find them to be consistent.
Feng, Chang; Cooray, Asantha; Keating, Brian
2017-02-01
The extragalactic γ-ray background and its spatial anisotropy could potentially contain a signature of dark matter (DM) annihilation or particle decay. Astrophysical foregrounds, such as blazars and star-forming galaxies (SFGs), however, dominate the γ-ray background, precluding an easy detection of the signal associated with the DM annihilation or decay in the background intensity spectrum. The DM imprint on the γ-ray background is expected to be correlated with large-scale structure tracers. In some cases, such a cross-correlation is even expected to have a higher signal-to-noise ratio than the auto-correlation. One reliable tracer of the DM distribution in the large-scale structure is lensing of the cosmic microwave background (CMB), and the cosmic infrared background (CIB) is a reliable tracer of SFGs. We analyze Fermi-LAT data taken over 92 months and study the cross-correlation with Planck CMB lensing, Planck CIB, and Fermi-γ maps. We put upper limits on the DM annihilation cross-section from the cross-power spectra with the γ-ray background anisotropies. The unbiased power spectrum estimation is validated with simulations that include cross-correlated signals. We also provide a set of systematic tests and show that no significant contaminations are found for the measurements presented here. Using γ-ray background map from data gathered over 92 months, we find the best constraint on the DM annihilation with a 1σ confidence level upper limit of 10‑25–10‑24 cm3 s‑1, when the mass of DM particles is between 20 and 100 GeV.
Modular Platforms for Optofluidic Systems
Brammer, Marko; Mappes, Timo
2014-01-01
Optofluidics is increasingly gaining impact in a number of different fields of research, namely biology and medicine, environmental monitoring and green energy. However, the market for optofluidic products is still in the early development phase. In this manuscript, we discuss modular platforms as a potential concept to facilitate the transfer of optofluidic sensing systems to an industrial implementation. We present microfluidic and optical networks as a basis for the interconnection of optofluidic sensor modules. Finally, we show the potential for entire optofluidic networks
Moreira, Silvana [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Civil, Arquitetura e Urbanismo]. E-mail: Silvana@fec.unicamp.br; Vives, Ana Elisa S. de [Universidade Metodista de Piracicaba (UNIMEP), Santa Barbara D' Oeste, SP (Brazil). Faculdade de Engenharia, Arquitetura e Urbanismo]. E-mail: aesvives@unimep.br; Brienza, Sandra Maria B. [Universidade Metodista de Piracicaba (UNIMEP), Santa Barbara D' Oeste, SP (Brazil) Faculdade de Ciencias Matematicas, da Natureza e de Tecnologia da Informacao]. E-mail: sbrienza@unimep.br; Medeiros, Jean Gabriel S.; Tomazello Filho, Mario [Sao Paulo Univ., Piracicaba, SP (Brazil). Escola Superior de Agricultura Luiz de Queiroz]. E-mail: jeangm@esalq.usp.br; mtomazel@esalq.usp.br; Zucchi, Orgheda L.A.D. [Sao Paulo Univ., Ribeirao Preto, SP (Brazil). Faculdade de Ciencias Farmaceuticas]. E-mail: olzucchi@fcfrp.usp.br; Nascimento Filho, Virgilio F. [Centro de Energia Nuclear na Agricultura (CENA), Piracicaba, SP (Brazil). Lab. de Instrumentacao Nuclear]. E-mail: virgilio@cena.usp.br
2005-07-01
This paper aims to study the environmental pollution in the tree development, as a manner to evaluate its use as bioindicator in urban and country sides. The sample collecting was carry out in Piracicaba city, Sao Paulo State, that presents high level of environmental contamination of the water, soil and air, due industrial activities, vehicles combustion, sugar-cane leaves burning in the harvesting, etc. It was selected the Caesalpinia peltophoroides ('Sibipiruna') specie because its very used in urban arborization. It was employed the analytical technique named total reflection X-ray fluorescence (TXRF) to identify and quantify the elements and metals of nutritional and toxicological importance in the wood samples. The analysis was done in the Brazilian Synchrotron Light Laboratory, using a white beam for excitation and a Si(Li) detector for characteristic X-ray detection. It was quantified the P, K, Ca, Ti, Fe, Sr, Ba e Pb elements. (author)
Hsu, Ming-Ying; Lin, Yu-Chuan; Chan, Chia-Yen; Lin, Wei-Cheng; Chan, Shenq-Tsong; Huang, Ting-Ming
2012-10-01
The Cassegrain telescope system in this study, is discussion correct lens thermal OPD (Optical Path Difference) effect optical performance. The correct lens assembly are includes several components such as correct lens, lens mount, spacer, mount barrel and retainer. The heat transfer from surrounding to the correct lens barrel will causes optical system aberration. Meanwhile, the off-axis rays path of the OPD must consider lens incidence point and emergence point. The correct lens temperature distribution is calculate the lens barrel heat transfer analysis, the thermal distortion and stress are solve by FEM (Finite Element Method) software. The temperature calculation results can be weighting to each incidence ray path and calculate thermal OPD. The thermal OPD on Z-direction can be fitted by rigid body motion and Zernike polynomial. The fitting results can be used to evaluate the thermal effect on correct lens assembly in telescope system.
Feng, Chang; Keating, Brian
2016-01-01
The extragalactic $\\gamma$-ray background, and its spatial anisotropy, could potentially contain a signature of dark matter annihilation or particle decay. Astrophysical foregrounds, such as blazars and star-forming galaxies, however, dominate the $\\gamma$-ray background, precluding an easy detection of the signal associated with the dark matter annihilation or decay in the background intensity spectrum. The dark matter imprint on the $\\gamma$-ray background is expected to be correlated with large-scale structure tracers. In some cases such a cross-correlation is even expected to have a higher signal-to-noise ratio than the auto-correlation. A reliable tracer of the dark matter distribution in the large-scale structure is lensing of the cosmic microwave background (CMB) and the cosmic infrared background (CIB) is a reliable tracer of star-forming galaxies. We analyze Fermi-LAT data taken over 92 months and study the cross-correlation with Planck CMB lensing, Planck CIB, and Fermi-$\\gamma$ maps. We put upper l...
Woods, R Jeremy; Brower, Justin O; Castellanos, Elena; Hashemzadeh, Mehrnoosh; Khakshoor, Omid; Russu, Wade A; Nowick, James S
2007-03-07
The development of peptide beta-hairpins is problematic, because folding depends on the amino acid sequence and changes to the sequence can significantly decrease folding. Robust beta-hairpins that can tolerate such changes are attractive tools for studying interactions involving protein beta-sheets and developing inhibitors of these interactions. This paper introduces a new class of peptide models of protein beta-sheets that addresses the problem of separating folding from the sequence. These model beta-sheets are macrocyclic peptides that fold in water to present a pentapeptide beta-strand along one edge; the other edge contains the tripeptide beta-strand mimic Hao [JACS 2000, 122, 7654] and two additional amino acids. The pentapeptide and Hao-containing peptide strands are connected by two delta-linked ornithine (deltaOrn) turns [JACS 2003, 125, 876]. Each deltaOrn turn contains a free alpha-amino group that permits the linking of individual modules to form divalent beta-sheets. These "cyclic modular beta-sheets" are synthesized by standard solid-phase peptide synthesis of a linear precursor followed by solution-phase cyclization. Eight cyclic modular beta-sheets 1a-1h containing sequences based on beta-amyloid and macrophage inflammatory protein 2 were synthesized and characterized by 1H NMR. Linked cyclic modular beta-sheet 2, which contains two modules of 1b, was also synthesized and characterized. 1H NMR studies show downfield alpha-proton chemical shifts, deltaOrn delta-proton magnetic anisotropy, and NOE cross-peaks that establish all compounds but 1c and 1g to be moderately or well folded into a conformation that resembles a beta-sheet. Pulsed-field gradient NMR diffusion experiments show little or no self-association at low (
Modular Robotics in an African Context
Lund, Henrik Hautop
2011-01-01
In this paper, we review the concept, development and use of modular robotic devices for education, health improvements, and business in Africa. The modular robotics inspired technology has the advantage of allowing any user easy access to a physical construction of new and advanced technology. We...... conceptualized several educational tools inspired by modular robotics for contextualized IT education in Tanzania, leading to a novel IT degree program and the development of East Africa’s first science and business park in Iringa, Tanzania. The prototypes inspired by modular robotics were developed in the local......, rural context and tested by local users in hospitals and rehabilitation centres. In this paper, we review the development of both modular building blocks for education and modular robotic tiles for rehabilitation in Tanzania....
(Automated) software modularization using community detection
Hansen, Klaus Marius; Manikas, Konstantinos
2015-01-01
detection algorithm of Reichardt and Bornholdt improved community quality for all systems, that coupling decreased for 99 of the systems, and that coherence increased for 102 of the systems. Furthermore, the modularity function correlates with existing metrics for coupling and coherence.......The modularity of a software system is known to have an effect on, among other, development effort, change impact, and technical debt. Modularizing a specific system and evaluating this modularization is, however, challenging. In this paper, we apply community detection methods to the graph...... of class dependencies in software systems to find optimal modularizations through communities. We evaluate this approach through a study of 111 Java systems contained in the Qualitas Corpus. We found that using the modularity function of Newman with an Erdős-Rényi null-model and using the community...
Modular Design in Treaty Verification Equipment
Macarthur, Duncan Whittemore [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Benz, Jacob [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tolk, Keith [Milagro Consulting, Albuquerque, NM (United States); Weber, Tom [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)
2015-01-27
It is widely believed that modular design is a good thing. However, there are often few explicit arguments, or even an agreed range of definitions, to back up this belief. In this paper, we examine the potential range of design modularity, the implications of various amounts of modularity, and the advantages and disadvantages of each level of modular construction. We conclude with a comparison of the advantages and disadvantages of each type, as well as discuss many caveats that should be observed to take advantage of the positive features of modularity and minimize the effects of the negative. The tradeoffs described in this paper will be evaluated during the conceptual design to determine what amount of modularity should be included.
Modular, Hierarchical Learning By Artificial Neural Networks
Baldi, Pierre F.; Toomarian, Nikzad
1996-01-01
Modular and hierarchical approach to supervised learning by artificial neural networks leads to neural networks more structured than neural networks in which all neurons fully interconnected. These networks utilize general feedforward flow of information and sparse recurrent connections to achieve dynamical effects. The modular organization, sparsity of modular units and connections, and fact that learning is much more circumscribed are all attractive features for designing neural-network hardware. Learning streamlined by imitating some aspects of biological neural networks.
A Modular Rewriting Semantics for CML
Chalub, Fabricio; Braga, Christiano de Oliveira
2004-01-01
This paper presents a modular rewriting semantics (MRS) specification for Reppy's Concurrent ML (CML), based on Peter Mosses' modular structural operational semantics specification for CML. A modular rewriting semantics specification for a programming language is a rewrite theory in rewriting log...... of rewriting logic, and to verify CML programs using Maude's built-in LTL model checker. It is assumed that the reader is familiar with basic concepts of structural operational semantics and algebraic specifications....
Identification of drivers for modular production
Brunoe, Thomas Ditlev; Bossen, Jacob; Nielsen, Kjeld
2015-01-01
Todays competitive environment in industry creates a need for companies to enhance their ability to introduce new products faster. To increase rampup speed reconfigurable manufacturing systems is a promising concept, however to implement this production platforms and modular manufacturing...... is required. This paper presents an analysis whether and which module drivers from general product development can be applied to the development process of a modular manufacturing system. The result is a compiled list of modular drivers for manufacturing and examples of their use....
Jiang, Jonathan Q
2011-01-01
We show here that the problem of maximizing a family of quantitative functions, encompassing both the modularity (Q-measure) and modularity density (D-measure), for community detection can be uniformly understood as a combinatoric optimization involving the trace of a matrix called modularity Laplacian. Instead of using traditional spectral relaxation, we apply additional nonnegative constraint into this graph clustering problem and design efficient algorithms to optimize the new objective. With the explicit nonnegative constraint, our solutions are very close to the ideal community indicator matrix and can directly assign nodes into communities. The near-orthogonal columns of the solution can be reformulated as the posterior probability of corresponding node belonging to each community. Therefore, the proposed method can be exploited to identify the fuzzy or overlapping communities and thus facilitates the understanding of the intrinsic structure of networks. Experimental results show that our new algorithm ...
Sirito de Vives, Ana Elisa [School of Civil Engineering, Architecture and Urban Design Methodist University of Piracicaba, Rodovia Santa Barbara D' Oeste/Iracemapolis, km 01, 13450-000 Santa Barbara D' Oeste, SP (Brazil)]. E-mail: aesvives@unimep.br; Moreira, Silvana [State University of Campinas - UNICAMP/FEC (Brazil); Brienza, Sandra Maria Boscolo [School of Civil Engineering, Architecture and Urban Design Methodist University of Piracicaba, Rodovia Santa Barbara D' Oeste/Iracemapolis, km 01, 13450-000 Santa Barbara D' Oeste, SP (Brazil); Silva Medeiros, Jean Gabriel [University of Sao Paulo - USP/ ESALQ (Brazil); Tomazello Filho, Mario Tomazello [University of Sao Paulo - USP/ ESALQ (Brazil); Araujo Domingues Zucchi, Orgheda Luiza [University of Sao Paulo - USP/FCFRP (Brazil); Nascimento Filho, Virgilio Franco do [University of Sao Paulo - USP/CENA (Brazil)
2006-11-15
This paper aims to study the environmental pollution in the tree development, in order to evaluate its use as bioindicator in urban and country sides. The sample collection was carried out in Piracicaba city, Sao Paulo State, which presents high level of environmental contamination in water, soil and air, due to industrial activities, vehicles combustion, sugar-cane leaves burning in the harvesting, etc. The species Caesalpinia peltophoroides ('Sibipiruna') was selected because it is widely used in urban forestation. Synchrotron Radiation Total Reflection X-ray Fluorescence technique (SR-TXRF) was employed to identify and quantify the elements and metals of nutritional and toxicological importance in the wood samples. The analysis was performed in the Brazilian Synchrotron Light Source Laboratory, using a white beam for excitation and a Si(Li) detector for X-ray detection. In several samples, P, K, Ca, Ti, Fe, Sr, Ba and Pb were quantified. The K/Ca, K/P and Pb/Ca ratios were found to decrease towards the bark.
Modularity and its effects on innovation
Boer, Henrike Engele Elisabeth; Hansen, Poul H. Kyvsgård
Purpose Through a discussion of the link between modularity and innovation, it is assessed whether and, then, when it is appropriate for an entrepreneur to apply modularity in his company’s innovation processes. Design/Methodology/Approach A conceptual paper, which aims to combine three theoretical...... fields: Modularity, Innovation, and Entrepreneurship Findings: Modularization can provide huge advantages for entrepreneurs. However, the true benefits can first be pursued when the product and production processes are mature enough. At this point of time the entrepreneur will need to accept more...
A SCALABLE HYBRID MODULAR MULTIPLICATION ALGORITHM
Meng Qiang; Chen Tao; Dai Zibin; Chen Quji
2008-01-01
Based on the analysis of several familiar large integer modular multiplication algorithms,this paper proposes a new Scalable Hybrid modular multiplication (SHyb) algorithm which has scalable operands, and presents an RSA algorithm model with scalable key size. Theoretical analysis shows that SHyb algorithm requires m2n/2+2m iterations to complete an mn-bit modular multiplication with the application of an n-bit modular addition hardware circuit. The number of the required iterations can be reduced to a half of that of the scalable Montgomery algorithm. Consequently, the application scope of the RSA cryptosystem is expanded and its operation speed is enhanced based on SHyb algorithm.
Problems in the theory of modular forms
Murty, M Ram; Graves, Hester
2016-01-01
This book introduces the reader to the fascinating world of modular forms through a problem-solving approach. As such, besides researchers, the book can be used by the undergraduate and graduate students for self-instruction. The topics covered include q-series, the modular group, the upper half-plane, modular forms of level one and higher level, the Ramanujan τ-function, the Petersson inner product, Hecke operators, Dirichlet series attached to modular forms and further special topics. It can be viewed as a gentle introduction for a deeper study of the subject. Thus, it is ideal for non-experts seeking an entry into the field. .
Functional annotation of hierarchical modularity.
Kanchana Padmanabhan
Full Text Available In biological networks of molecular interactions in a cell, network motifs that are biologically relevant are also functionally coherent, or form functional modules. These functionally coherent modules combine in a hierarchical manner into larger, less cohesive subsystems, thus revealing one of the essential design principles of system-level cellular organization and function-hierarchical modularity. Arguably, hierarchical modularity has not been explicitly taken into consideration by most, if not all, functional annotation systems. As a result, the existing methods would often fail to assign a statistically significant functional coherence score to biologically relevant molecular machines. We developed a methodology for hierarchical functional annotation. Given the hierarchical taxonomy of functional concepts (e.g., Gene Ontology and the association of individual genes or proteins with these concepts (e.g., GO terms, our method will assign a Hierarchical Modularity Score (HMS to each node in the hierarchy of functional modules; the HMS score and its p-value measure functional coherence of each module in the hierarchy. While existing methods annotate each module with a set of "enriched" functional terms in a bag of genes, our complementary method provides the hierarchical functional annotation of the modules and their hierarchically organized components. A hierarchical organization of functional modules often comes as a bi-product of cluster analysis of gene expression data or protein interaction data. Otherwise, our method will automatically build such a hierarchy by directly incorporating the functional taxonomy information into the hierarchy search process and by allowing multi-functional genes to be part of more than one component in the hierarchy. In addition, its underlying HMS scoring metric ensures that functional specificity of the terms across different levels of the hierarchical taxonomy is properly treated. We have evaluated our
Geometric Kac-Moody Modularity
Lynker, M; Lynker, Monika; Schimmrigk, Rolf
2004-01-01
It is shown how the arithmetic structure of algebraic curves encoded in the Hasse-Weil L-function can be related to affine Kac-Moody algebras. This result is useful in relating the arithmetic geometry of Calabi-Yau varieties to the underlying exactly solvable theory. In the case of the genus three Fermat curve we identify the Hasse-Weil L-function with the Mellin transform of the twist of a number theoretic modular form derived from the string function of a non-twisted affine Lie algebra. The twist character is associated to the number field of quantum dimensions of the conformal field theory.
Modular training for career counsellors
Maruša Goršak
2015-12-01
Full Text Available Exactly ten years have passed since first attempts were made in Slovenia to establish a comprehensive and formalized educational program for counsellors working in the field of lifelong career guidance. In the past, organizations providing (career guidance services have established their own non-formal employee trainings. A step forward has been made under the framework of the project “National coordination point for lifelong career guidance”, which enabled the implementation of the first joint training for (career guidance counsellors, called Modular training of career counsellors.
Hamdi Sahraoui
2016-08-01
Full Text Available Lead (Pb, Zinc (Zn and Cadmium (Cd levels on soils surrounding of Lakhouat mine (North-West of Tunisia were measured. The total concentration of these elements in the soil samples was determined by portable X-ray fluorescence (XRF in situ and compared to the traditional digestion method using inductively coupled-plasma optical emission spectroscopy (ICP-OES. Statistical analyses were performed to determine if significant differences existed between the instrumental techniques, which included simple correlations by the regression lines and t-test for mean comparison. The statistical analysis demonstrated that no statistically significant differences were observed for the Pb concentrations; however, for the Zn and Cd concentrations, t-test showed significant differences between the inst
Sen, N; Roy, N K; Das, A K
1989-06-01
Separation by solvent extraction followed by X-ray fluorescence spectrometry has been used for determination of molybdenum and tungsten in rocks and minerals. Samples are decomposed either by heating with a mixture of hydrofluoric acid and perchloric acid or by fusion with potassium pyrosulphate, followed by extraction of molybdenum and tungsten with N-benzoylphenylhydroxylamine in toluene from 4-5M sulphuric acid medium. The extract is collected on a mass of cellulose powder, which is dried in vacuum, mixed thoroughly and pressed into a disc for XRF measurements. The method is free from all matrix effects and needs no mathematical corrections for interelement effects. The method is suitable for determination of molybdenum and tungsten in geological materials down to ppm levels, with reasonable precision and accuracy.
Ribstein, B.; Achatz, U.
2016-09-01
Gravity waves (GWs) play an important role in atmospheric dynamics. Due to their short wavelengths, they must be parameterized in current weather and forecast models, which cannot resolve them explicitly. We are here the first to report the possibility and the implication of having an online GW parameterization in a linear but global model that incorporates their horizontal propagation, the effects of transients and of horizontal background gradients on GW dynamics. The GW parameterization is based on a ray-tracer model with a spectral formulation that is safe against numerical instabilities due to caustics. The global model integrates the linearized primitive equations to obtain solar tides (STs), with a seasonally dependent reference climatology, forced by a climatological daily cycle of the tropospheric and stratospheric heating, and the (instantaneous) GW momentum and buoyancy flux convergences resulting from the ray tracer. Under a more conventional "single-column" approximation, where GWs only propagate vertically and do not respond to horizontal gradients of the resolved flow, GW impacts are shown to be significantly changed in comparison with "full" experiments, leading to significant differences in ST amplitudes and phases, pointing at a sensitive issue of GW parameterizations in general. In the full experiment, significant semidiurnal STs arise even if the tidal model is only forced by diurnal heating rates. This indicates that an important part of the tidal signal is forced directly by GWs via their momentum and buoyancy deposition. In general, the effect of horizontal GW propagation and the GW response to horizontal large-scale flow gradients is rather observed in nonmigrating than in migrating tidal components.
Trace Elements in Ovaries: Measurement and Physiology.
Ceko, Melanie J; O'Leary, Sean; Harris, Hugh H; Hummitzsch, Katja; Rodgers, Raymond J
2016-04-01
Traditionally, research in the field of trace element biology and human and animal health has largely depended on epidemiological methods to demonstrate involvement in biological processes. These studies were typically followed by trace element supplementation trials or attempts at identification of the biochemical pathways involved. With the discovery of biological molecules that contain the trace elements, such as matrix metalloproteinases containing zinc (Zn), cytochrome P450 enzymes containing iron (Fe), and selenoproteins containing selenium (Se), much of the current research focuses on these molecules, and, hence, only indirectly on trace elements themselves. This review focuses largely on two synchrotron-based x-ray techniques: X-ray absorption spectroscopy and x-ray fluorescence imaging that can be used to identify the in situ speciation and distribution of trace elements in tissues, using our recent studies of bovine ovaries, where the distribution of Fe, Se, Zn, and bromine were determined. It also discusses the value of other techniques, such as inductively coupled plasma mass spectrometry, used to garner information about the concentrations and elemental state of the trace elements. These applications to measure trace elemental distributions in bovine ovaries at high resolutions provide new insights into possible roles for trace elements in the ovary.
Compactification of Drinfeld modular varieties and Drinfeld Modular Forms of Arbitrary Rank
Pink, Richard
2010-01-01
We give an abstract characterization of the Satake compactification of a general Drinfeld modular variety. We prove that it exists and is unique up to unique isomorphism, though we do not give an explicit stratification by Drinfeld modular varieties of smaller rank which is also expected. We construct a natural ample invertible sheaf on it, such that the global sections of its $k$-th power form the space of (algebraic) Drinfeld modular forms of weight~$k$. We show how the Satake compactification and modular forms behave under all natural morphisms between Drinfeld modular varieties; in particular we define Hecke operators. We give explicit results in some special cases.
Modularity, noise, and natural selection.
Marroig, Gabriel; Melo, Diogo A R; Garcia, Guilherme
2012-05-01
Most biological systems are formed by component parts that are to some degree interrelated. Groups of parts that are more associated among themselves and are relatively autonomous from others are called modules. One of the consequences of modularity is that biological systems usually present an unequal distribution of the genetic variation among traits. Estimating the covariance matrix that describes these systems is a difficult problem due to a number of factors such as poor sample sizes and measurement errors. We show that this problem will be exacerbated whenever matrix inversion is required, as in directional selection reconstruction analysis. We explore the consequences of varying degrees of modularity and signal-to-noise ratio on selection reconstruction. We then present and test the efficiency of available methods for controlling noise in matrix estimates. In our simulations, controlling matrices for noise vastly improves the reconstruction of selection gradients. We also perform an analysis of selection gradients reconstruction over a New World Monkeys skull database to illustrate the impact of noise on such analyses. Noise-controlled estimates render far more plausible interpretations that are in full agreement with previous results. © 2012 The Author(s). Evolution© 2012 The Society for the Study of Evolution.
Decentralized and Modular Electrical Architecture
Elisabelar, Christian; Lebaratoux, Laurence
2014-08-01
This paper presents the studies made on the definition and design of a decentralized and modular electrical architecture that can be used for power distribution, active thermal control (ATC), standard inputs-outputs electrical interfaces.Traditionally implemented inside central unit like OBC or RTU, these interfaces can be dispatched in the satellite by using MicroRTU.CNES propose a similar approach of MicroRTU. The system is based on a bus called BRIO (Bus Réparti des IO), which is composed, by a power bus and a RS485 digital bus. BRIO architecture is made with several miniature terminals called BTCU (BRIO Terminal Control Unit) distributed in the spacecraft.The challenge was to design and develop the BTCU with very little volume, low consumption and low cost. The standard BTCU models are developed and qualified with a configuration dedicated to ATC, while the first flight model will fly on MICROSCOPE for PYRO actuations and analogue acquisitions. The design of the BTCU is made in order to be easily adaptable for all type of electric interface needs.Extension of this concept is envisaged for power conditioning and distribution unit, and a Modular PCDU based on BRIO concept is proposed.
Modular polynomials via isogeny volcanoes
Broker, Reinier; Sutherland, Andrew V
2010-01-01
We present a new algorithm to compute the classical modular polynomial Phi_n in the rings Z[X,Y] and (Z/mZ)[X,Y], for a prime n and any positive integer m. Our approach uses the graph of n-isogenies to efficiently compute Phi_n mod p for many primes p of a suitable form, and then applies the Chinese Remainder Theorem (CRT). Under the Generalized Riemann Hypothesis (GRH), we achieve an expected running time of O(n^3 (log n)^3 log log n), and compute Phi_n mod m using O(n^2 (log n)^2 + n^2 log m) space. We have used the new algorithm to compute Phi_n with n over 5000, and Phi_n mod m with n over 20000. We also consider several modular functions g for which Phi_n^g is smaller than Phi_n, allowing us to handle n over 60000.
Modular invariance and the fusion algebra
Dijkgraaf, Robbert; Verlinde, Erik
1988-12-01
We discuss the relation between modular transformations and the fusion algebra, and explain its proof. It is shown that the existence of off-diagonal modular invariant partition functions imply the existence of a non-trivial automorphism of the fusion algebra. This is illustrated using the SU(2) affine models.
Algebra and Arithmetic of Modular Forms
Rustom, Nadim
In [Rus14b] and [Rus14a], we study graded rings of modular forms over congruence subgroups, with coefficients in subrings A of C, and determine bounds of the weights of modular forms constituting a minimal set of generators, as well as on the degree of the generators of the ideal of relations bet...
A Modular Laser Graphics Projection System
Newswanger, Craig D.
1984-05-01
WED Enterprises has designed and built a modular projection system for the presentation of animated laser shows. This system was designed specifically for use in Disney theme shows. Its modular design allows it to be adapted to many show situations with simple hardware and software adjustments. The primary goals were superior animation, long life, low maintenance and stand alone operation.
Modular bootstrap in Liouville field theory
Hadasz, Leszek, E-mail: hadasz@th.if.uj.edu.p [M. Smoluchowski Institute of Physics, Jagiellonian University, Reymonta 4, 30-059 Krakow (Poland); Jaskolski, Zbigniew, E-mail: jask@ift.uni.wroc.p [Institute of Theoretical Physics, University of Wroclaw, pl. M. Borna, 50-204 Wroclaw (Poland); Suchanek, Paulina, E-mail: paulina@ift.uni.wroc.p [Institute of Theoretical Physics, University of Wroclaw, pl. M. Borna, 50-204 Wroclaw (Poland)
2010-02-22
The modular matrix for the generic 1-point conformal blocks on the torus is expressed in terms of the fusion matrix for the 4-point blocks on the sphere. The modular invariance of the toric 1-point functions in the Liouville field theory with DOZZ structure constants is proved.
Modular bootstrap in Liouville field theory
Hadasz, Leszek; Suchanek, Paulina
2009-01-01
The modular matrix for the generic 1-point conformal blocks on the torus is expressed in terms of the fusion matrix for the 4-point blocks on the sphere. The modular invariance of the toric 1-point functions in the Liouville field theory with DOZZ structure constants is proved.
Analytic properties of the Virasoro modular kernel
Nemkov, Nikita
2016-01-01
On the space of generic conformal blocks the modular transformation of the underlying surface is realized as a linear integral transformation. We show that the analytic properties of conformal block implied by Zamolodchikov's formula are shared by the kernel of the modular transformation and illustrate this by explicit computation in the case of the one-point toric conformal block.
Detectability thresholds of general modular graphs
Kawamoto, Tatsuro
2016-01-01
We investigate the detectability thresholds of various modular structures in the stochastic block model. Our analysis reveals how the detectability threshold is related to the details of the modular pattern, including the hierarchy of the clusters. We show that certain planted structures are impossible to infer regardless of their fuzziness.
Modular Construction: The Wave of the Future.
Savage, Chuck
1989-01-01
Modular construction of school buildings offers speed of construction, with 100 percent contractor responsibility for the completed structures. Under negotiated terms, modular projects can be purchased outright or through long-term leasing arrangements that provide ownership at the end of the lease period. (MLF)
Mapping Modular SOS to Rewriting Logic
Braga, Christiano de Oliveira; Haeusler, Edward Hermann; Meseguer, José;
2003-01-01
Modular SOS (MSOS) is a framework created to improve the modularity of structural operational semantics specifications, a formalism frequently used in the fields of programming languages semantics and process algebras. With the objective of defining formal tools to support the execution and verif...
Complex Convexity of Orlicz Modular Sequence Spaces
Lili Chen
2016-01-01
Full Text Available The concepts of complex extreme points, complex strongly extreme points, complex strict convexity, and complex midpoint locally uniform convexity in general modular spaces are introduced. Then we prove that, for any Orlicz modular sequence space lΦ,ρ, lΦ,ρ is complex midpoint locally uniformly convex. As a corollary, lΦ,ρ is also complex strictly convex.
Analytic properties of the Virasoro modular kernel
Nemkov, Nikita [Moscow Institute of Physics and Technology (MIPT), Dolgoprudny (Russian Federation); Institute for Theoretical and Experimental Physics (ITEP), Moscow (Russian Federation); National University of Science and Technology MISIS, The Laboratory of Superconducting metamaterials, Moscow (Russian Federation)
2017-06-15
On the space of generic conformal blocks the modular transformation of the underlying surface is realized as a linear integral transformation. We show that the analytic properties of conformal block implied by Zamolodchikov's formula are shared by the kernel of the modular transformation and illustrate this by explicit computation in the case of the one-point toric conformal block. (orig.)
The Algorithmic Complexity of Modular Decomposition
J.C. Bioch (Cor)
2001-01-01
textabstractModular decomposition is a thoroughly investigated topic in many areas such as switching theory, reliability theory, game theory and graph theory. We propose an O(mn)-algorithm for the recognition of a modular set of a monotone Boolean function f with m prime implicants and n variables.
Algebra and Arithmetic of Modular Forms
Rustom, Nadim
In [Rus14b] and [Rus14a], we study graded rings of modular forms over congruence subgroups, with coefficients in subrings A of C, and determine bounds of the weights of modular forms constituting a minimal set of generators, as well as on the degree of the generators of the ideal of relations bet...
Modular Power Architectures for Microgrid Clusters
Lin, Hengwei; Liu, Leo; Guerrero, Josep M.
2014-01-01
. The user-frame concept proposed here when designing microgrids considers that the end-user is the basis for the geographical deployment. Meanwhile, a modular user-oriented approach is adopted in order to enhance reliability and expansibility. Finally, a unified dispatching and hierarchical management...... approach is proposed and evaluated to effectively optimize and manage modular microgrid architectures....
Magalhães, T.; Carvalho, M. L.; Von Bohlen, A.; Becker, M.
2010-06-01
In this work Total-reflection X-ray fluorescence (TXRF) was used to analyse healthy and cancerous tissues of the same individual along several contiguous thin sections of each tissue. Thirty two samples (16 pairs) of breast tissue, 30 samples (15 pairs) of intestine tissue and 10 samples (5 pairs) of stomach tissue were analysed. The samples were obtained in Civil Hospitals of Germany (Dortmund) and Portugal (Lisbon). The elemental distribution of P, S, Cl, K, Ca, Cr, Mn, Fe, Ni, Cu, Zn, Se, Br, Rb, Sr and Pb in these samples was studied. Descriptive statistics based on bar graphics and hypotheses tests and also an automatic classification based on hierarchical grouping analysis was used for the several analysed tissues. It was shown that the behaviour of the elements is tissue dependent. Some elements, like P and K exhibit the same behaviour in all the analysed tissue types. They have increased concentrations in all cancerous tissues. Unlike, other elements like Br show completely different behaviour depending on the tissue: similar concentration in healthy and cancerous stomach, decreased levels in colon cancerous tissues and enhanced concentrations in breast was observed. Moreover cancer tissues present decreased Se concentrations on colon and increased on breast.
Takahashi, Atsushi; Igarashi, Shukuro; Ueki, Yasuo [Ibaraki Univ., Hitachi (Japan). Faculty of Engineering; Yamaguchi, Hitoshi [National Research Inst. for Metals, Ibaraki (Japan)
2000-11-01
A homogeneous liquid-liquid extraction method for 36 metal ions with diethyldithiocarbamate was studied. As a result, 11 metal ions were extracted as metal-chelates. Under the experimental conditions, the maximum concentration factor was 500 (i.e., 0.1 mL of sedimented liquid phase was produced from 50 mL of aqueous phase). Moreover, the proposed method was utilized as a preconcentration method for X-ray fluorescence analysis of these metals. The recovery of each metal was ca. 97-100%. All calibration curves were linear over the range of 5.0 x 10{sup -7} mol L{sup -1} to 1.0 x 10{sup -5} mol L{sup -1}. The detection limits were at the 10{sup -8} mol L{sup -1} levels and the relative standard deviations were below 5% (5 determinations). When the proposed method was used for the determination of contaminants in a synthetic sample (Al-based alloy model) and of components in an Au-Pd alloy, the results were satisfactory. (orig.)