Performance evaluation of nuclear grade filters for the Trupact-I pressure equalization system

International Nuclear Information System (INIS)

Sandoval, R.P.; Joseph, B.J.

1987-01-01

The performance of high-efficiency-particulate-air and ultra-low- penetration-air filters subjected to extreme environments of temperature, shock, pressure, and particulate loading was evaluated in a test program at the Sandia National Laboratories. The test program was initiated to evaluate the feasibility of using commercially available nuclear-grade filters in the filtered pressure equalization system of a contact-handled transuranic waste transport system, called TRUPACT-I. The filtered pressure equalization system of TRUPACT-I assures containment of the activity within the limits permitted by federal regulations and simultaneously equalizes the pressure between the cavity of the packaging and the environment, and minimizes the buildup of radiolytically generated gases. The filters were exposed to temperatures, pressures and stresses that exceed expected environments in normal and accident conditions of transport. The performance of the test filters was determined by measuring and quantifying filter efficiency and the Darcy constant. In addition, the integrity of the filter housing was evaluated using non-destructive helium leak testing. The details of the test program and results obtained from the tests are presented in this paper

Experimental study on reduced moderation BWR with Advanced Recycle System (BARS)

International Nuclear Information System (INIS)

Hiraiwa, K.; Yoshioka, K.; Yamamoto, Y.; Akiba, M.; Yamaoka, M.; Abe, N.; Mimatsu, J.

2004-01-01

Experimental study has been done for reduced-moderation spectrum boiling water reactor named BARS (BWR with Advanced Recycle System). The critical assembly experiment for triangular tight uranium lattice has been done in TOSHIBA critical assembly (NCA). Experimental method based on modified conversion ratio was adopted to evaluate the void reactivity effect. Void fraction was simulated by formed polystyrene in this experiment. The measured void coefficient for tight uranium lattice agreed with calculation. The thermal hydraulic test study has been done to study the coolability of BARS lattice. Visual test and high-pressure thermal hydraulic test have been done as the thermal hydraulic test. Visual test has indicated the flow behavior for BARS lattice is same as that of current BWR. The high-pressure thermal hydraulic test has indicated the applicability of modified Arai's correlation to the BARS lattice. (authors)

Evaluating the BD-100R [Bubble Technology Industries] as a neutron spectrometer through pressure variation

International Nuclear Information System (INIS)

White, B.; Ebert, D.; Munno, F.

1990-01-01

Other investigators have evaluated the dose response of neutron bubble dosimeters for possible use as personnel monitors for the U.S. Navy in low level radiation fields. In addition to dose measurements, these devices have been modified to measure the neutron energy spectra. These methods tend to be cumbersome, inaccurate, or both and do not use the same devices as employed in the dosimetry. The BD-100R dosimeter used in this work consists of a test tube containing an elastic polymer with interspersed droplets of two types of Freon; Freon-12 and Freon-114. Each superheated liquid droplet is a potential nucleation site. The minimum energy needed to form a bubble from the nucleation site is given by, E = 16πγ 3 (T)/3(ΔP) 2 , where ΔP is the difference between the vapor pressure of the droplet and the applied pressure. Upon reaching a critical radius, a bubble becomes unstable and grows in size. It may be seen from this equation that the energy deposition required for bubble formation is inversely proportional to the square of the pressure difference. The number of bubbles formed continually decreases with increasing applied pressure, until a pressure is reached where no bubbles are formed since the energy transferred can no longer vaporize the Freon. This investigation is intended to demonstrate the determination of an unknown spectrum utilizing the dosimeter response (number of bubbles formed) as a function of the neutron energy (applied pressure). A set of 12 dosimeters was initially exposed outside the East Beam Port (EBP) at the Maryland University Training Reactor (MUTR). The dosimeters were inside a pressure chamber which could accommodate up to 18 dosimeters. The same set of dosimeters were irradiated using a paraffin moderated PuBe source for which the neutron energy spectrum is unknown. There were eight exposures of six dosimeters at varied pressures in the EBP. The average number of bubbles and standard deviation was measured for each pressure. Data

Increased intracranial pressure: evaluation by computerized tomography

International Nuclear Information System (INIS)

Lightfoote, W.E.; Pressman, B.D.

1975-01-01

Computerized tomography is clearly very useful in the evaluation of patients with increased intracranial pressure and suspected pseudotumor cerebri. It provides an index of ventricular size and configuration and has the capability of demonstrating intracranial lesions. Moreover, this new technique is rapid and non-invasive, and is without attendant risks. Examinations may be performed serially as the clinical process evolves, thereby giving roentgenographic correlation to the clinical features. (U.S.)

Effects of hiking at moderate and low altitude on cardiovascular parameters in male patients with metabolic syndrome: Austrian Moderate Altitude Study.

Science.gov (United States)

Neumayr, Günther; Fries, Dietmar; Mittermayer, Markus; Humpeler, Egon; Klingler, Anton; Schobersberger, Wolfgang; Spiesberger, Reinhard; Pokan, Rochus; Schmid, Peter; Berent, Robert

2014-09-01

Physical activity is a cornerstone in therapy for patients with metabolic syndrome. Walking and hiking in a mountain scenery represents an ideal approach to make them move. The Austrian Moderate Altitude Study (AMAS) 2000 main study is a randomized controlled trial to investigate the cardiovascular effects of hiking at moderate altitude on patients with metabolic syndrome compared with a control group at low altitude, to assess a potential altitude-specific effect. Seventy-one male patients with metabolic syndrome were randomly assigned to a moderate altitude group (at 1700 m), with 36 participants, or to a low altitude group (at 200 m), with 35 participants. The 3-week vacation program included 12 hiking tours (4 per week, average duration 2.5 hours, intensity 55% to 65% of heart rate maximum). Physical parameters, performance capacity, 24-hour blood pressure, and heart rate profiles were obtained before, during, and after the stay. In both groups, we found a significant mean weight loss of -3.13 kg; changes in performance capacity were minor. Systolic, diastolic, and mean arterial pressures and circadian heart rate profiles were significantly reduced in both groups, with no differences between them. Consequently, the pressure-rate product was reduced as well. All study participants tolerated the vacation well without any adverse events. A 3-week hiking vacation at moderate or low altitude is safe for patients with metabolic syndrome and provides several improvements in their cardiovascular parameters. The cardiovascular benefits achieved are more likely to be the result of regular physical activity than the altitude-specific effect of a mountain environment. Copyright © 2014 Wilderness Medical Society. Published by Elsevier Inc. All rights reserved.

Walking the straight and narrow: the moderating effect of evaluation apprehension on the relationship between collectivism and corruption.

Science.gov (United States)

Huang, Zhen-wei; Liu, Li; Zheng, Wen-wen; Tan, Xu-yun; Zhao, Xian

2015-01-01

Previous studies obtained mixed results regarding the association between collectivism and corruption. To make sense of the mixed results, the current research examined the moderating role of evaluation apprehension on the relationship between collectivism and corruption. Study 1, using a bribery scenario, indicated that collectivism facilitated corruption only when evaluation apprehension was low. Study 2, using a real money bribery game, confirmed the moderated model found in Study 1. Study 3 further demonstrated the different effects of vertical/horizontal collectivism on corruption. Our results suggest that a society may effectively combat corruption by increasing its social costs while, at the same time, retaining its collectivistic values.

Pressure tube type research reactor

International Nuclear Information System (INIS)

Ueda, Hiroshi.

1976-01-01

Object: To prevent excessive heat generation due to radiation of a pressure tube vessel. Structure: A pressure tube encasing therein a core comprises a dual construction comprising inner and outer tubes coaxially disposed. High speed cooling water is passed through the inner tube for cooling. In addition, in the outer periphery of said outer tube there is provided a forced cooling tube disposed coaxially thereto, into which cooling fluid, for example, such as moderator or reflector is forcibly passed. This forced cooling tube has its outer periphery surrounded by the vessel into which moderator or reflector is fed. By the provision of the dual construction of the pressure tube and the forced cooling tube, the vessel may be prevented from heat generation. (Ikeda, J.)

Criticality evaluations with moderators other than water for uranium metal fuels

International Nuclear Information System (INIS)

Toffer, H.; Tollefson, D.A.; Finfrock, S.H.

1986-01-01

Occasionally, nuclear criticality safety analyses of fissile material handling operations or transport situations require consideration of moderation other than water. Such moderators could be oils, plastics, wood, concrete, carbon, or even wet sand. All of these materials contain either hydrogen, carbon, or mixtures of the two elements as the principal moderators. Other elements as part of the compounds or mixtures contribute less to the neutron slowing down process and can possibly be significant parasitic neutron absorbers. Results of a series of calculations are presented illustrating the impact of various moderators on critical masses or critical parameters as a function of lattice pitch for different uranium metal fuel elements at low 235 U enrichments. Several nuclear criticality safety analyses performed at the Hanford N Reactor, operated by UNC Nuclear Industries for the US Department of Energy, have considered alternative moderators to assure that water moderation represented the most limiting case

Improved Slow-Positron Yield using a Single Crystal Tungsten Moderator

DEFF Research Database (Denmark)

Vehanen, A.; Lynn, K. G.; Schultz, P. J.

1983-01-01

A well-annealed W(110) single crystal was used as a fast-to-slow positron moderator. The measured moderator efficiency at room temperature using a58Co positron source in the backscattering geometry isɛ =(3.2±0.4)×10−3, roughly a factor of three better thanɛ for the best previously reported Cu(111......)+S moderator. We find a stable positron moderation efficiency over a period of several weeks when maintained at pressures around 10−9 Torr and an energy spreadΔE = 0.7 eV of the emitted slow positrons. An initial attempt was made to fabricate a hybrid Cu on W(110) moderator, which yieldedɛ of about 1...

Pressure Ulcer Risk Evaluation in Critical Patients: Clinical and Social Characteristics.

Science.gov (United States)

de Azevedo Macena, Mônica Suêla; da Costa Silva, Rayanne Suely; Dias Fernandes, Maria Isabel Da Conceição; de Almeida Medeiros, Ana Beatriz; Batista Lúcio, Kadyjina Daiane; de Carvalho Lira, Ana Luisa Brandão

2017-01-01

Pressure ulcers increase hospital stays and treatment costs due to their complications. Therefore, recognizing factors that contribute to pressure ulcer risk are important to patient safety. To evaluate the association between the scores of the Waterlow, Braden, and Norton scales and clinical and social characteristics in critically ill patients. A cross-sectional study of 78 patients in an adult intensive care unit of a university hospital in Northeastern Brazil was conducted from July to December 2015. Data included social and clinical information and the risk factors of the Braden, Norton and Waterlow scales. Data were analysed by the descriptive and inferential statistics. Most of the participants were female, adults and elderly people with brown skin colour, low education levels and insufficient income. Most of them showed a high risk for developing pressure ulcers using the three evaluated scales. Age, smoking status, diabetes and hypertension were associated with scores on the Waterlow, Braden and Norton scales. Age, use of the tobacco, diabetes and hypertension were associated with the risk of pressure ulcers in ICU patients.

Prospective clinical study to evaluate an oscillometric blood pressure monitor in pet rabbits.

Science.gov (United States)

Bellini, Luca; Veladiano, Irene A; Schrank, Magdalena; Candaten, Matteo; Mollo, Antonio

2018-02-27

Rabbits are particularly sensitive to develop hypotension during sedation or anaesthesia. Values of systolic or mean non-invasive arterial blood pressure below 80 or 60 mmHg respectively are common under anaesthesia despite an ongoing surgery. A reliable method of monitoring arterial blood pressure is extremely important, although invasive technique is not always possible due to the anatomy and dimension of the artery. The aim of this study was to evaluate the agreement between a new oscillometric device for non-invasive arterial blood pressure measurement and the invasive method. Moreover the trending ability of the device, ability to identify changes in the same direction with the invasive methods, was evaluated as well as the sensibility of the device in identifying hypotension arbitrarily defined as invasive arterial blood pressure below 80 or 60 mmHg. Bland-Altman analysis for repeated measurements showed a poor agreement between the two methods; the oscillometric device overestimated the invasive arterial blood pressure, particularly at high arterial pressure values. The same analysis repeated considering oscillometric measurement that match invasive mean pressure lower or equal to 60 mmHg showed a decrease in biases and limits of agreement between methods. The trending ability of the device, evaluated with both the 4-quadrant plot and the polar plot was poor. Concordance rate of mean arterial blood pressure was higher than systolic and diastolic pressure although inferior to 90%. The sensibility of the device in detecting hypotension defined as systolic or mean invasive arterial blood pressure lower than 80 or 60 mmHg was superior for mean oscillometric pressure rather than systolic. A sensitivity of 92% was achieved with an oscillometric measurement for mean pressure below 65 mmHg instead of 60 mmHg. Non-invasive systolic blood pressure is less sensitive as indicator of hypotension regardless of the cutoff limit considered. Although mean invasive

Influence of depth of neuromuscular blockade on surgical conditions during low-pressure pneumoperitoneum laparoscopic cholecystectomy: A randomized blinded study.

Science.gov (United States)

Barrio, Javier; Errando, Carlos L; García-Ramón, Jaime; Sellés, Rafael; San Miguel, Guillermo; Gallego, Juan

2017-11-01

To evaluate the influence of neuromuscular blockade (NMB) on surgical conditions during low-pressure pneumoperitoneum (8mmHg) laparoscopic cholecystectomy (LC), while comparing moderate and deep NMB. Secondary objective was to evaluate if surgical conditions during low-pressure pneumoperitoneum LC performed with deep NMB could be comparable to those provided during standard-pressure pneumoperitoneum (12mmHg) LC. Prospective, randomized, blinded clinical trial. Operating room. Ninety ASA 1-2 patients scheduled for elective LC. Patients were allocated into 3 groups: Group 1: low-pressure pneumoperitoneum with moderate-NMB (1-3 TOF), Group 2: low-pressure pneumoperitoneum with deep-NMB (1-5 PTC) and Group 3: standard pneumoperitoneum (12mmHg). Rocuronium was used to induce NMB and acceleromiography was used for NMB monitoring (TOF-Watch-SX). Three experienced surgeons evaluated surgical conditions using a four-step scale at three time-points: surgical field exposure, dissection of the gallbladder and extraction/closure. Low-pressure pneumoperitoneum (Group 1 vs. 2): good conditions: 96.7 vs. 96.7%, 90 vs. 80% and 89.6 vs. 92.3%, respectively for the time-points, p>0.05. No differences in optimal surgical conditions were observed between the groups. Surgery completion at 8mmHg pneumoperitoneum: 96.7 vs. 86.7%, p=0.353. Standard-pressure pneumoperitoneum vs. low-pressure pneumoperitoneum with deep NMB (Group 3 vs. 2): good conditions: 100% in Group 3 for the three time-points (p=0.024 vs. Group 2 at dissection of the gallbladder). Significantly greater percentage of optimal conditions during standard-pressure pneumoperitoneum LC at the three time points of evaluation. The depth of NMB was found not to be decisive neither in the improvement of surgical conditions nor in the completion of low-pressure pneumoperitoneum LC performed by experienced surgeons. Surgical conditions were considered better with a standard-pressure pneumoperitoneum, regardless of the depth of NMB

Evaluation of Pharmacokinetic and Pharmacodynamic Drug-Drug Interaction of Sacubitril/Valsartan (LCZ696) and Sildenafil in Patients With Mild-to-Moderate Hypertension.

Science.gov (United States)

Hsiao, H-L; Langenickel, T H; Petruck, J; Kode, K; Ayalasomayajula, S; Schuehly, U; Greeley, M; Pal, P; Zhou, W; Prescott, M F; Sunkara, G; Rajman, I

2018-03-01

Sacubitril/valsartan (LCZ696) is indicated for the treatment of patients with heart failure and reduced ejection fraction (HFrEF). Since patients with HFrEF may receive sacubitril/valsartan and sildenafil, both increasing cyclic guanosine monophosphate, the present study evaluated the pharmacokinetic and pharmacodynamic drug interaction potential between sacubitril/valsartan and sildenafil. In this open-label, three-period, single sequence study, patients with mild-to-moderate hypertension (153.8 ± 8.2 mmHg mean systolic blood pressure (SBP)) received a single dose of sildenafil 50 mg, sacubitril/valsartan 400 mg once daily for 5 days, and sacubitril/valsartan and sildenafil coadministration. When coadministered with sildenafil, the AUC and C max of valsartan decreased by 29% and 39%, respectively. Coadministration of sacubitril/valsartan and sildenafil resulted in a greater decrease in BP (-5/-4/-4 mmHg mean ambulatory SBP/DBP/MAP (mean arterial pressure)) than with sacubitril/valsartan alone. Both treatments were generally safe and well tolerated in this study; however, the additional BP reduction suggests that sildenafil should be administered cautiously in patients receiving sacubitril/valsartan. Unique identifier: NCT01601470. © 2017 The Authors Clinical Pharmacology & Therapeutics published by Wiley Periodicals, Inc. on behalf of American Society for Clinical Pharmacology and Therapeutics.

Moderator purification and design modifications based on operation feedback

International Nuclear Information System (INIS)

Das, S.; Chakrabarti, A.K.; Shirolkar, K.M.; Sharma, V.K.

1994-01-01

Heavy water is used as a moderator in the Pressurized Heavy Water Reactors using natural uranium as a fissile fuel. The purification system is provided to maintain the purity of moderator heavy water so as to minimise the radiolytic decomposition of heavy water due to nuclear radiation which otherwise would lead to hazardous concentration of deuterium in the moderator cover gas. The presence of dissolved impurity in the moderator increases the radiolysis rate by impeding the reverse reaction and hence these must be removed. The purification system in general controls the chemistry of moderator by minimizing the corrosion of piping in the circuit and along with the liquid poison injection system adjusts the concentration of the poisons in the moderator. This paper describes the evolution of the purification system for the 500 MWe PHWRs based on various operating requirements and feedback from the operating stations. (author)

Nonlinear focal shift beyond the geometrical focus in moderately focused acoustic beams.

Science.gov (United States)

Camarena, Francisco; Adrián-Martínez, Silvia; Jiménez, Noé; Sánchez-Morcillo, Víctor

2013-08-01

The phenomenon of the displacement of the position along the axis of the pressure, intensity, and radiation force maxima of focused acoustic beams under increasing driving voltages (nonlinear focal shift) is studied for the case of a moderately focused beam. The theoretical and experimental results show the existence of this shift along the axis when the initial pressure in the transducer increases until the acoustic field reaches the fully developed nonlinear regime of propagation. Experimental data show that at high amplitudes and for moderate focusing, the position of the on-axis pressure maximum and radiation force maximum can surpass the geometrical focal length. On the contrary, the on-axis pressure minimum approaches the transducer under increasing driving voltages, increasing the distance between the positive and negative peak pressure in the beam. These results are in agreement with numerical KZK model predictions and the existed data of other authors and can be explained according to the effect of self-refraction characteristic of the nonlinear regime of propagation.

Consideration on evaluation of internal pressure creep rupture for tube with circumferential joint

International Nuclear Information System (INIS)

Nagato, Kotaro; Satoh, Keisuke

1983-01-01

The behavior of internal pressure creep rupture of the thin-walled cylinders with circumferential joints is affected by the combination of creep characteristics of parent materials and weld metals. In particular, the compatibility of the creep strain rate of parent materials and weld metals becomes an important controlling factor. The behavior of internal pressure creep of the welded parts in circumferential joint cylinders can be evaluated simply with the uniaxial creep data of parent materials and weld metals, considering it by approximately substituting with the creep behavior of a uniaxial longitudinal joint. The method of evaluation is, first, to analyze the breaking behavior of uniaxial longitudinal joints using the uniaxial creep characteristic values of parent materials and weld metals, and next, by combining the equation for the relation between the rupture times of uniaxial creep and internal pressure creep with the analyzed breaking behavior of uniaxial joints, the internal pressure creep rupture behavior of the cylinders with circumferential joints can be evaluated. The internal pressure creep behavior of the thin-walled cylinders with circumferential joints, their rupture life and the uniaxial creep rupture life of longitudinal joints, and the examination of Hastelloy X cylinders are reported. (Kako, I.)

An analytical evaluation for the pressure drop characteristics of bottom nozzle flow holes

International Nuclear Information System (INIS)

Yang, S. G.; Kim, H. J.; Lim, H. T.; Park, E. J.; Jeon, K. L.

2002-01-01

An analytical evaluation for the bottom nozzle flow holes was performed to find a best design concept in terms of pressure drop. For this analysis, Computational Fluid Dynamics (CFD), FLUENT 5.5, code was selected as an analytical evaluation tool. The applicability of CFD code was verified by benchmarking study with Vibration Investigation of Small-scale Test Assemblies (VISTA) test data in several flow conditions and typical flow hole shape. From this verification, the analytical data were benchmarked roughly within 17% to the VISTA test data. And, overall trend under various flow conditions looked very similar between both cases. Based on the evaluated results using CFD code, it is concluded that the deburring and multiple chamfer hole features at leading edge are the excellent design concept to decrease pressure drop across bottom nozzle plate. The deburring and multiple chamfer hole features at leading edge on the bottom nozzle plate have 12% and 17% pressure drop benefit against a single chamfer hole feature on the bottom nozzle plate, respectively. These design features are meaningful and applicable as a low pressure drop design concept of bottom nozzle for Pressurized Water Reactor (PWR) fuel assembly

Development of high pressure conductivity probe (HPCP) for secondary shut down system (SDS-2) of 500 MWe PHWR

International Nuclear Information System (INIS)

Sapra, M.K.; Kundu, S.; Mohan, L.R.

2003-09-01

The poison solution and the moderator in Secondary Shutdown System (SDS-2) of 500 MWe PHWR, are separated by their own liquid in liquid interface. This interface moves towards the calandria because of molecular diffusion, temperature difference and physical disturbances in the moderator level. It is proposed to install two numbers of high pressure conductivity probes (HPCP) to monitor the interface movement as well as to provide the safe annunciation value for interface location. On actuation of the SDS-2 signal, high-pressure helium will inject the poison into the moderator to shutdown the reactor. During poison injection, these probes will experience high pressure of nearly 85 kg/sq.cm. Global market survey indicated that conductivity probes having built in temperature sensor are available for a maximum pressure rating of 35 kg/sq.cm. Hence in order to meet the process requirement of SDS-2, the development of HPCP suitable for a pressure of 85 kg/sq.cm. was taken up. Two numbers of such probes were successfully designed, fabricated and evaluated for their performance. The developed conductivity probes fully meet the laid design and performance criteria. The aforesaid development work was a successful endeavour towards indigenisation of high-pressure conductivity probe for future applications. This report deals with the design aspects, fabrication technique, material and performance evajuation criteria and test results of HPCP. (author)

Effects of a high-intensity interval training program versus a moderate-intensity continuous training program on maximal oxygen uptake and blood pressure in healthy adults: study protocol for a randomized controlled trial.

Science.gov (United States)

Arboleda Serna, Víctor Hugo; Arango Vélez, Elkin Fernando; Gómez Arias, Rubén Darío; Feito, Yuri

2016-08-18

Participation in aerobic exercise generates increased cardiorespiratory fitness, which results in a protective factor for cardiovascular disease and all-cause mortality. High-intensity interval training might cause higher increases in cardiorespiratory fitness in comparison with moderate-intensity continuous training; nevertheless, current evidence is not conclusive. To our knowledge, this is the first study to test the effect of high-intensity interval training with total load duration of 7.5 min per session. A randomized controlled trial will be performed on two groups of healthy, sedentary male volunteers (n = 44). The study protocol will include 24 exercise sessions, three times a week, including aerobic training on a treadmill and strength training exercises. The intervention group will perform 15 bouts of 30 s, each at an intensity between 90 % and 95 % of maximal heart rate. The control group will complete 40 min of continuous exercise, ranging between 65 % and 75 % of maximal heart rate. The primary outcome measure to be evaluated will be maximal oxygen uptake (VO2max), and systolic and diastolic blood pressure will be evaluated as secondary outcome measures. Waist circumference, body mass index, and body composition will also be evaluated. Epidemiological evidence shows the link between VO2max and its association with chronic conditions that trigger CVD. Therefore, finding ways to improve VO2max and reduce blood pressure it is of vital importance to public health. NCT02288403 . Registered on 4 November 2014.

Power spectral density measurements with 252Cf for a light water moderated research reactor

International Nuclear Information System (INIS)

King, W.T.; Mihalczo, J.T.

1979-01-01

A method of determining the reactivity of far subcritical systems from neutron noise power spectral density measurements with 252 Cf has previously been tested in fast reactor critical assemblies: a mockup of the Fast Flux Test Facility reactor and a uranium metal sphere. Calculations indicated that this measurement was feasible for a pressurized water reactor (PWR). In order to evaluate the ability to perform these measurements with moderated reactors which have long prompt neutron lifetimes, measurements were performed with a small plate-type research reactor whose neutron lifetime (57 microseconds) was about a factor of three longer than that of a PWR and approx. 50% longer than that of a boiling water reactor. The results of the first measurements of power spectral densities with 252 Cf for a water moderated reactor are presented

Fluid moderator control system reactor internals distribution system

International Nuclear Information System (INIS)

Fensterer, H.F.; Klassen, W.E.; Veronesi, L.; Boyle, D.E.; Salton, R.B.

1987-01-01

This patent describes a spectral shift pressurized water nuclear reactor employing a low neutron moderating fluid for the spectral shift including a reactor pressure vessel, a core comprising a plurality of fuel assemblies, a core support plate, apparatus comprising means for penetrating the reactor vessel for introducing the moderating fluid into the reactor vessel. Means associated with the core support plate for directly distributing the moderating fluid to and from the fuel assemblies comprises at least one inlet flow channel in the core plate; branch inlet feed lines connect to the inlet flow channel in the core plate; vertical inlet flow lines flow connected to the branch inlet feed lines; each vertical flow line communicates with a fuel assembly; the distribution means further comprise lines serving as return flow lines, each of which is connected to one of the fuel assemblies; branch exit flow lines in the core plate flow connected to the return flow lines of the fuel assembly; and at least one outlet flow channel flow connected to the branch exit flow lines; and a flow port interposed between the penetration means and the distribution means for flow connecting the penetration means with the distribution means

Evaluation of Low Pressure Fogging System for Improving Crop Yield of Tomato (Lycopersicon esculentum Mill.: Grown under Heat Stress Conditions

Directory of Open Access Journals (Sweden)

Kobi Shilo

2013-06-01

Full Text Available In Mediterranean regions, many tomato plants are grown throughout the hot summer period (May–September in sheltered cultivation, mainly for plant protection reasons. Most of the shelters that are used are low cost net houses covered with 50 mesh insect proof net. In most cases these net houses have a flat roof and no ventilation or climate control measures. This insufficient ventilation during the hot summer leads to above optimal air temperatures and causes moderate heat stress inside the shelters, which leads to yield reduction. The aim of this study was to evaluate the ability of a simple and inexpensive low pressure fogging system installed in a naturally ventilated net house to lower temperatures and improve the yield during the summer. The study showed that in areas where relative air humidity (RH during the daytime is less than 60%, tomato plants improved their performance when grown through the summer in net houses under moderate heat stress. Under fogging conditions pollen grain viability and fruit set were significantly improved. This improvement influenced the yield picked during September (104–136 DAP. However, total seasonal yield was not affected by the fogging treatment.

Kinetics of Pressurized Water Reactors with Hot or Cold Moderators

Energy Technology Data Exchange (ETDEWEB)

Norinder, O

1960-11-15

The set of neutron kinetic equations developed in this report permits the use of long integration steps during stepwise integration. Thermal relations which describe the transfer of heat from fuel to coolant are derived. The influence upon the kinetic behavior of the reactor of a number of parameters is studied. A comparison of the kinetic properties of the hot and cold moderators is given.

Reduction of peak plantar pressure in people with diabetes-related peripheral neuropathy: an evaluation of the DH Pressure Relief Shoe™

Directory of Open Access Journals (Sweden)

Raspovic Anita

2012-10-01

Full Text Available Abstract Background Offloading plantar pressure is a key strategy for the prevention or healing of neuropathic plantar ulcers in diabetes. Non-removable walking casts, such as total contact casts, are currently considered the gold-standard for offloading this type of wound. However, alternative methods for offloading that are more cost effective and easier to use are continually being sought. The aim of this study was to evaluate the capacity of the DH Pressure Relief Shoe™ to offload high pressure areas under the neuropathic foot in diabetes. Methods A within-subjects, repeated measures design was used. Sixteen participants with diabetic peripheral neuropathy were recruited and three footwear conditions were evaluated in a randomised order: a canvas shoe (the control, the participants’ own standard shoe, and the DH Pressure Relief Shoe™. The primary outcome was peak plantar pressure, measured using the pedar-X® mobile in-shoe system between the three conditions. Results Data analysis was conducted on 14 out of the 16 participants because two participants could not complete data collection. The mean peak pressure values in kPa (±SD for each condition were: control shoe 315.9 (±140.7, participants’ standard shoe 273.0 (±127.1 and DH Pressure Relief Shoe™ 155.4 (±89.9. There was a statistically significant difference in peak plantar pressure between the DH Pressure Relief Shoe™ compared to both the control shoe (p = 0.002 and participants’ standard shoe (p = 0.001. The DH Pressure Relief Shoe™ decreased plantar pressures by 51% compared to the control shoe and by 43% compared to participants’ standard shoe. Importantly, for a couple of study participants, the DH Pressure Relief Shoe™ appeared unsuitable for day-to-day wearing. Conclusions The DH Pressure Relief Shoe™ reduced plantar pressures more than the other two shoe conditions. The DH Pressure Relief Shoe™ may be a useful alternative to current offloading

Moderator purification and design modifications based on operation feedback

Energy Technology Data Exchange (ETDEWEB)

Das, S; Chakrabarti, A K; Shirolkar, K M; Sharma, V K [Nuclear Power Corporation, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Heavy water is used as a moderator in the Pressurized Heavy Water Reactors using natural uranium as a fissile fuel. The purification system is provided to maintain the purity of moderator heavy water so as to minimise the radiolytic decomposition of heavy water due to nuclear radiation which otherwise would lead to hazardous concentration of deuterium in the moderator cover gas. The presence of dissolved impurity in the moderator increases the radiolysis rate by impeding the reverse reaction and hence these must be removed. The purification system in general controls the chemistry of moderator by minimizing the corrosion of piping in the circuit and along with the liquid poison injection system adjusts the concentration of the poisons in the moderator. This paper describes the evolution of the purification system for the 500 MWe PHWRs based on various operating requirements and feedback from the operating stations. (author). 2 refs., 3 figs., 1 tab.

Auditory feedback improves heart rate moderation during moderate-intensity exercise.

Science.gov (United States)

Shaykevich, Alex; Grove, J Robert; Jackson, Ben; Landers, Grant J; Dimmock, James

2015-05-01

The objective of this study is to determine whether exposure to automated HR feedback can produce improvements in the ability to regulate HR during moderate-intensity exercise and to evaluate the persistence of these improvements after feedback is removed. Twenty healthy adults performed 10 indoor exercise sessions on cycle ergometers over 5 wk after a twice-weekly schedule. During these sessions (FB), participants received auditory feedback designed to maintain HR within a personalized, moderate-intensity training zone between 70% and 80% of estimated maximum HR. All feedback was delivered via a custom mobile software application. Participants underwent an initial assessment (PREFB) to measure their ability to maintain exercise intensity defined by the training zone without use of feedback. After completing the feedback training, participants performed three additional assessments identical to PREFB at 1 wk (POST1), 2 wk (POST2), and 4 wk (POST3) after their last feedback session. Time in zone (TIZ), defined as the ratio of the time spent within the training zone divided by the overall time of exercise, rate of perceived exertion, instrumental attitudes, and affective attitudes were then evaluated to assess results using two-way, mixed-model ANOVA with sessions and gender as factors. Training with feedback significantly improved TIZ (P moderate-intensity exercise in healthy adults.

Basic conceptions for reactor pressure vessel manipulators and their evaluation

International Nuclear Information System (INIS)

Popp, P.

1987-01-01

The study deals with application fields and basic design conceptions of manipulators in reactor pressure vessels as well as their evaluation. It is shown that manipulators supported at the reactor flange have essential advantages

Abnormal albuminuria and blood pressure rise in incipient diabetic nephropathy induced by exercise

DEFF Research Database (Denmark)

Christensen, Cramer

1984-01-01

The aim of the study was to evaluate the influence of light to moderate dynamic work (450 kpm/min followed by 600 kpm/min during 20 min each) on the blood pressure and renal protein handling in insulin-dependent diabetic patients with incipient nephropathy (D3) (elevated baseline albumin excretion...... diastolic blood pressure was elevated [92.1 mm Hg +/- 6.0 (mean +/- SD)] compared to D2 (80.9 mm Hg +/- 4.8, 2P = 0.003%) and C (79.5 mm Hg +/- 12.4, 2P = 1.2%). Baseline systolic blood pressure was not significantly different in the three groups, but systolic blood pressure was more elevated at 600 kpm...... blood pressure and maximal exercise induced albumin excretion was demonstrable in D3.(ABSTRACT TRUNCATED AT 250 WORDS)...

Analysis and evaluation system for elevated temperature design of pressure vessels

International Nuclear Information System (INIS)

Hayakawa, Teiji; Sayawaki, Masaaki; Nishitani, Masahiro; Mii, Tatsuo; Murasawa, Kanji

1977-01-01

In pressure vessel technology, intensive efforts have recently been made to develop the elevated temperature design methods. Much of the impetus of these efforts has been provided mainly by the results of the Liquid Metal Fast Breeder Reactor (LMFBR) and more recently, of the High Temperature Gas-cooled Reactor (HTGR) Programs. The pressure vessels and associated components in these new type nuclear power plants must operate for long periods at elevated temperature where creep effects are significant and then must be designed by rigorous analysis for high reliability and safety. To carry out such an elevated temperature designing, numbers of highly developed analysis and evaluation techniques, which are so complicated as to be impossible by manual work, are indispensable. Under these circumstances, the authors have made the following approaches in the study: (1) Study into basic concepts and the associated techniques in elevated temperature design. (2) Systematization (Analysis System) of the procedure for loads and stress analyses. (3) Development of post-processor, ''POST-1592'', for strength evaluation based on ASME Code Case 1592-7. By linking the POST-1592 together with the Analysis System, an analysis and evaluation system is developed for an elevated temperature design of pressure vessels. Consequently, designing of elevated temperature vessels by detailed analysis and evaluation has easily and effectively become feasible by applying this software system. (auth.)

Evaluation of monkey intraocular pressure by rebound tonometer

Science.gov (United States)

Yu, Wenhan; Cao, Guiqun; Qiu, Jinghua; Ma, Jia; Li, Ni; Yu, Man; Yan, Naihong; Chen, Lei; Pang, Iok-Hou

2009-01-01

Purpose To evaluate the usefulness of the TonoVet™ rebound tonometer in measuring intraocular pressure (IOP) of monkeys. Methods The accuracy of the TonoVet™ rebound tonometer was determined in cannulated eyes of anesthetized rhesus monkeys where IOP was controlled by adjusting the height of a connected perfusate reservoir. To assess the applicability of the equipment through in vivo studies, the diurnal fluctuation of IOP and effects of IOP-lowering compounds were evaluated in monkeys. Results IOP readings generated by the TonoVet™ tonometer correlated very well with the actual pressure in the cannulated monkey eye. The linear correlation had a slope of 0.922±0.014 (mean±SEM, n=4), a y-intercept of 3.04±0.61, and a correlation coefficient of r2=0.97. Using this method, diurnal IOP fluctuation of the rhesus monkey was demonstrated. The tonometer was also able to detect IOP changes induced by pharmacologically active compounds. A single topical ocular instillation (15 μg) of the rho kinase inhibitor, H1152, produced a 5–6 mmHg reduction (pmonkey eye. PMID:19898690

Higher levels of spontaneous breathing reduce lung injury in experimental moderate acute respiratory distress syndrome.

Science.gov (United States)

Carvalho, Nadja C; Güldner, Andreas; Beda, Alessandro; Rentzsch, Ines; Uhlig, Christopher; Dittrich, Susanne; Spieth, Peter M; Wiedemann, Bärbel; Kasper, Michael; Koch, Thea; Richter, Torsten; Rocco, Patricia R; Pelosi, Paolo; de Abreu, Marcelo Gama

2014-11-01

To assess the effects of different levels of spontaneous breathing during biphasic positive airway pressure/airway pressure release ventilation on lung function and injury in an experimental model of moderate acute respiratory distress syndrome. Multiple-arm randomized experimental study. University hospital research facility. Thirty-six juvenile pigs. Pigs were anesthetized, intubated, and mechanically ventilated. Moderate acute respiratory distress syndrome was induced by repetitive saline lung lavage. Biphasic positive airway pressure/airway pressure release ventilation was conducted using the airway pressure release ventilation mode with an inspiratory/expiratory ratio of 1:1. Animals were randomly assigned to one of four levels of spontaneous breath in total minute ventilation (n = 9 per group, 6 hr each): 1) biphasic positive airway pressure/airway pressure release ventilation, 0%; 2) biphasic positive airway pressure/airway pressure release ventilation, > 0-30%; 3) biphasic positive airway pressure/airway pressure release ventilation, > 30-60%, and 4) biphasic positive airway pressure/airway pressure release ventilation, > 60%. The inspiratory effort measured by the esophageal pressure time product increased proportionally to the amount of spontaneous breath and was accompanied by improvements in oxygenation and respiratory system elastance. Compared with biphasic positive airway pressure/airway pressure release ventilation of 0%, biphasic positive airway pressure/airway pressure release ventilation more than 60% resulted in lowest venous admixture, as well as peak and mean airway and transpulmonary pressures, redistributed ventilation to dependent lung regions, reduced the cumulative diffuse alveolar damage score across lungs (median [interquartile range], 11 [3-40] vs 18 [2-69]; p ventilation more than 0-30% and more than 30-60% showed a less consistent pattern of improvement in lung function, inflammation, and damage compared with biphasic positive airway

Inhibitory self-control moderates the effect of changed implicit food evaluations on snack food consumption.

Science.gov (United States)

Haynes, Ashleigh; Kemps, Eva; Moffitt, Robyn

2015-07-01

The current study used a modified implicit association test (IAT) to change implicit evaluations of unhealthy snack food and tested its effects on subsequent consumption. Furthermore, we investigated whether these effects were moderated by inhibitory self-control. A sample of 148 women (17-25 years) motivated to manage weight through healthy eating completed an IAT intervention, and pre- and post-intervention IATs assessing implicit evaluations of unhealthy food. The intervention IAT trained participants to pair unhealthy food stimuli with either positive or negative stimuli. A task disguised as a taste-test was used to assess consumption of unhealthy snack foods. Inhibitory self-control was measured using a self-report scale. As predicted, the implicit evaluation of unhealthy food became more negative from pre- to post-training among participants in the food negative pairing condition; however, there was no corresponding change in the food positive pairing condition. The effect of the training on snack consumption was moderated by inhibitory self-control with only participants low in inhibitory self-control having lower snack intake following the food negative training. This finding is consistent with dual-process models of behaviour which predict that self-control capacity renders impulses less influential on behaviour. Furthermore, it suggests that an intervention that retrains implicit food evaluations could be effective at reducing unhealthy eating, particularly among those with low inhibitory self-control. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evaluation of upper-shelf toughness requirements for reactor pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Gamble, R.M.; Zahoor, A. (NOVETECH Corp., Rockville, MD (USA)); Hiser, A. (Materials Engineering Associates, Inc., Lanham, MD (USA)); Ernst, H.A.; Pollitz, E.T. (Georgia Inst. of Tech., Atlanta, GA (USA))

1990-04-01

This work assesses and applies the criteria recommended by the ASME Subgroup on Evaluation Standards for the evaluation of reactor pressure vessel beltline materials having upper shelf Charpy energies less than 50 ft-lbs. The assessment included comparison of the upper shelf energies required by the criteria recommended for Service Level A and B conditions and criteria proposed for evaluation of postulated Service Level C and D events. The criteria recommended for Service Level A and B conditions was used to evaluate Linde 80 weld material. 9 refs., 4 figs.

Evaluation of upper-shelf toughness requirements for reactor pressure vessels

International Nuclear Information System (INIS)

Gamble, R.M.; Zahoor, A.; Hiser, A.; Ernst, H.A.; Pollitz, E.T.

1990-04-01

This work assesses and applies the criteria recommended by the ASME Subgroup on Evaluation Standards for the evaluation of reactor pressure vessel beltline materials having upper shelf Charpy energies less than 50 ft-lbs. The assessment included comparison of the upper shelf energies required by the criteria recommended for Service Level A and B conditions and criteria proposed for evaluation of postulated Service Level C and D events. The criteria recommended for Service Level A and B conditions was used to evaluate Linde 80 weld material. 9 refs., 4 figs

Elderly people and ulcer caused by pressure at home care service

Directory of Open Access Journals (Sweden)

Ana Débora Alcantara Coêlho

2012-09-01

Full Text Available This research aimed at estimating the prevalence of pressure ulcers in a home care service. Cross-sectional study carried out in July/August 2009 with 194 bedridden aged patients. For data collection, the Braden Scale and an instrument consisting of demographics, clinical data, and preventive measures for pressure ulcers were applied. Data was analyzed using SPSS16.0 and presented as descriptive statistics. From the total sample, 69.6% (n = 135 were female; 68% (n = 132 ≥ 80 years old; 33% (n=64 were Alzheimer patients, and 26.3% (n = 51 had sequels of stroke; 31.4% (n = 61 had pressure ulcers, from which 54.1% (n = 33 were developed in the hospital. A prevalence of 31.4% and moderate risk (13.2% for pressure ulcers was identified. It is recommended longitudinal study for evaluating the relationship between the Braden Scale indicators and the development of pressure ulcers.

Moderate temperature gas purification system: application to high calorific coal derived fuel

Energy Technology Data Exchange (ETDEWEB)

M. Kobayashi; H. Shirai; M. Nunokawa [Central Research Institute of Electric Power Industry (CRIEPI), Kanagawa (Japan)

2005-07-01

Simultaneous removal of dust, alkaline and alkaline-earth metals, halides and sulfur compounds is required to enlarge application of coal-derived gas to the high temperature fuel cells and the fuel synthesis through chemical processing. Because high calorific fuel gas, such as oxygen-blown coal gas, has high carbon monoxide content, high temperature gas purification system is always subjected to the carbon deposition and slippage of contaminant of high vapor pressure. It was suggested that moderate temperature operation of the gas purification system is applied to avoid the harmful disproportionation reaction and efficient removal of the various contaminants. To establish the moderate temperature gas purification system, the chemical-removal processes where the reaction rate is predominant to the performance of contaminant removal should be evaluated. Performance of the removal processes for halides and sulfur compounds were experimentally evaluated. The halide removal process with sodium based sorbent had potential good performance at around 300{sup o}C. The sulfur removal process was also applicable to the temperature range, although the improvement of the sulfidation reaction rate is considered to be essential. 11 refs., 8 figs., 1 tab.

Evaluative threat and ambulatory blood pressure: cardiovascular effects of social stress in daily experience.

Science.gov (United States)

Smith, Timothy W; Birmingham, Wendy; Uchino, Bert N

2012-11-01

Physiological effects of social evaluation are central in models of psychosocial influences on physical health. Experimental manipulations of evaluative threat evoke substantial cardiovascular and neuroendocrine responses in laboratory studies, but only preliminary evidence is available regarding naturally occurring evaluative threats in daily life. In such nonexperimental ambulatory studies, it is essential to distinguish effects of evaluative threat from related constructs known to alter stress, such as ability perceptions and concerns about appearance. 94 married, working couples (mean age 29.2 years) completed a 1-day (8 a.m. to 10 p.m.) ambulatory blood pressure protocol with random interval-contingent measurements using a Suntech monitor and Palm Pilot-based measures of control variables and momentary experiences of social-evaluative threat, concerns about appearance, and perceived ability. In hierarchical analyses for couples and multiple measurement occasions (Proc Mixed; SAS) and controlling individual differences (BMI, age, income) and potential confounds (e.g., posture, activity), higher reports of social-evaluative threat were associated with higher concurrent systolic (estimate = .87, SE = .34) and diastolic blood pressure (estimate = 1.06; SE = .26), both p social-evaluative threat remained significant when perceived ability and appearance concerns were controlled. Naturally occurring social-evaluative threat during daily activity is associated with increased systolic and diastolic blood pressure. Given associations between ambulatory blood pressure and risk of cardiovascular disease, the findings support conceptual models of threats to the social self as a potentially important influence on physical health.

Evaluation of CANDU NPP containment structure subjected to aging and internal pressure increase

Energy Technology Data Exchange (ETDEWEB)

Huang, Xu [Department of Civil Engineering, University of Toronto, Toronto M5S 1A4 (Canada); Kwon, Oh-Sung, E-mail: os.kwon@utoronto.ca [Department of Civil Engineering, University of Toronto, Toronto M5S 1A4 (Canada); Bentz, Evan [Department of Civil Engineering, University of Toronto, Toronto M5S 1A4 (Canada); Tcherner, Julia [Candu Energy Inc. a member of SNC-Lavalin Group, Mississauga L5K 1B1 (Canada)

2017-04-01

Highlights: • The aging effects on the performance of a nuclear containment structure is evaluated. • A numerical model of the structure is subjected to increasing internal pressure. • No through-thickness cracks are predicted under the design level internal pressure. • The structure is predicted to be ductile up to large internal pressure levels. - Abstract: The objective of this study is to investigate the long-term performance of a typical CANDU® containment structure. A three-dimensional nonlinear finite element model was built to realistically evaluate the performance of the structure under service load as well as a hypothetical beyond-design level internal pressure. Consideration is given to the time-dependent effects, such as shrinkage, creep, and relaxation of prestressing tendons, over a 60-year timeframe. In addition, the sensitivity of the response of the containment structure against support condition, internal temperature profile and temporary construction openings was also investigated. The accuracy of the numerical model was validated against structural measurements made during a routine leak rate test. The analysis results show that the containment structure would develop a ductile mechanism if the internal pressure significantly exceeded the design pressure. The pressure-deformation relationship of the structure is sensitive to the considered time-dependent parameters.

The effects of perspective-taking on prejudice: the moderating role of self-evaluation.

Science.gov (United States)

Galinsky, Adam D; Ku, Gillian

2004-05-01

Perspective-taking, by means of creating an overlap between self and other cognitive representations, has been found to effectively decrease stereotyping and ingroup favoritism. In the present investigation, the authors examined the potential moderating role of self-esteem on the effects of perspective-taking on prejudice. In two experiments, it was found that perspective-takers, but not control participants, with temporarily or chronically high self-esteem evaluated an outgroup more positively than perspective-takers with low self-esteem. This finding suggests an irony of perspective-taking: it builds off egocentric biases to improve outgroup evaluations. The discussion focuses on how debiasing intergroup thought is often best accomplished by working through the very processes that produced the bias in the first place.

Characterization of gait in female patients with moderate to severe hallux valgus deformity.

Science.gov (United States)

Chopra, S; Moerenhout, K; Crevoisier, X

2015-07-01

Hallux valgus is one of the most common forefoot problems in females. Studies have looked at gait alterations due to hallux valgus deformity, assessing temporal, kinematic or plantar pressure parameters individually. The present study, however, aims to assess all listed parameters at once and to isolate the most clinically relevant gait parameters for moderate to severe hallux valgus deformity with the intent of improving post-operative patient prognosis and rehabilitation. The study included 26 feet with moderate to severe hallux valgus deformity and 30 feet with no sign of hallux valgus in female participants. Initially, weight bearing radiographs and foot and ankle clinical scores were assessed. Gait assessment was then performed utilizing pressure insoles (PEDAR) and inertial sensors (Physilog) and the two groups were compared using a non-parametric statistical hypothesis test (Wilcoxon rank sum, Phallux valgus group compared to controls and 9 gait parameters (effect size between 1.03 and 1.76) were successfully isolated to best describe the altered gait in hallux valgus deformity (r(2)=0.71) as well as showed good correlation with clinical scores. Our results, and nine listed parameters, could serve as benchmark for characterization of hallux valgus and objective evaluation of treatment efficacy. Copyright © 2015 Elsevier Ltd. All rights reserved.

EQUATIONS FOR GAS RELEASING PROCESS FROM PRESSURIZED VESSELS IN ODH EVALUATION

International Nuclear Information System (INIS)

JIA, L.X.; WANG, L.

2001-01-01

IN THE EVALUATION OF ODH, THE CALCULATION OF THE SPILL RATE FROM THE PRESSURIZED VESSEL IS THE CENTRAL TASK. THE ACCURACY OF THE ENGINEERING ESTIMATION BECOMES ONE OF THE SAFETY DESIGN ISSUES. THIS PAPER SUMMARIZES THE EQUATIONS FOR THE OXYGEN CONCENTRATION CALCULATION IN DIFFERENT CASES, AND DISCUSSES THE EQUATIONS FOR THE GAS RELEASE PROCESS CALCULATION BOTH FOR THE HIGH-PRESSURE GAS TANK AND THE LOW-TEMPERATURE LIQUID CONTAINER

Spontaneous breathing during lung-protective ventilation in an experimental acute lung injury model: high transpulmonary pressure associated with strong spontaneous breathing effort may worsen lung injury.

Science.gov (United States)

Yoshida, Takeshi; Uchiyama, Akinori; Matsuura, Nariaki; Mashimo, Takashi; Fujino, Yuji

2012-05-01

We investigated whether potentially injurious transpulmonary pressure could be generated by strong spontaneous breathing and exacerbate lung injury even when plateau pressure is limited to ventilation, each combined with weak or strong spontaneous breathing effort. Inspiratory pressure for low tidal volume ventilation was set at 10 cm H2O and tidal volume at 6 mL/kg. For moderate tidal volume ventilation, the values were 20 cm H2O and 7-9 mL/kg. The groups were: low tidal volume ventilation+spontaneous breathingweak, low tidal volume ventilation+spontaneous breathingstrong, moderate tidal volume ventilation+spontaneous breathingweak, and moderate tidal volume ventilation+spontaneous breathingstrong. Each group had the same settings for positive end-expiratory pressure of 8 cm H2O. Respiratory variables were measured every 60 mins. Distribution of lung aeration and alveolar collapse were histologically evaluated. Low tidal volume ventilation+spontaneous breathingstrong showed the most favorable oxygenation and compliance of respiratory system, and the best lung aeration. By contrast, in moderate tidal volume ventilation+spontaneous breathingstrong, the greatest atelectasis with numerous neutrophils was observed. While we applied settings to maintain plateau pressure at ventilation+spontaneous breathingstrong, transpulmonary pressure rose >33 cm H2O. Both minute ventilation and respiratory rate were higher in the strong spontaneous breathing groups. Even when plateau pressure is limited to mechanical ventilation, transpulmonary pressure and tidal volume should be strictly controlled to prevent further lung injury.

Microbial quality of soil from the Pampa biome in response to different grazing pressures

Directory of Open Access Journals (Sweden)

Rafael S. Vargas

2015-06-01

Full Text Available The aim of this study was to evaluate the impact of different grazing pressures on the activity and diversity of soil bacteria. We performed a long-term experiment in Eldorado do Sul, southern Brazil, that assessed three levels of grazing pressure: high pressure (HP, with 4% herbage allowance (HA, moderate pressure (MP, with 12% HA, and low pressure (LP, with 16% HA. Two reference areas were also assessed, one of never-grazed native vegetation (NG and another of regenerated vegetation after two years of grazing (RG. Soil samples were evaluated for microbial biomass and enzymatic (β-glucosidase, arylsulfatase and urease activities. The structure of the bacterial community and the population of diazotrophic bacteria were evaluated by RFLP of the 16S rRNA and nifH genes, respectively. The diversity of diazotrophic bacteria was assessed by partial sequencing of the 16S rDNA gene. The presence of grazing animals increased soil microbial biomass in MP and HP. The structures of the bacterial community and the populations of diazotrophic bacteria were altered by the different grazing managements, with a greater diversity of diazotrophic bacteria in the LP treatment. Based on the characteristics evaluated, the MP treatment was the most appropriate for animal production and conservation of the Pampa biome.

Effect of telmisartan on arterial distensibility and central blood pressure in patients with mild to moderate hypertension and Type 2 diabetes mellitus

Directory of Open Access Journals (Sweden)

Roland Asmar

2001-06-01

Full Text Available Arterial wall stiffness is an important independent risk factor for cardiovascular disease in hypertensive patients, which is further exacerbated by co-existent diabetes mellitus. Increased arterial stiffness is directly associated with an increase in pulse wave velocity (PWV and indirectly with increased central and peripheral blood pressure. Following a two-week placebo run-in period, 27 patients with mild to moderate essential hypertension and Type 2 diabetes mellitus, were randomised to once daily treatment with either telmisartan 40 mg or placebo for three weeks, and after a two-week washout period, crossed-over to the alternative treatment for a further three weeks. Carotid/femoral and carotid/radial PWV were measured non-invasively using the automatic Complior® device, and central parameters (central blood pressure, pulse contour analysis, and augmentation index were measured using the SphygmoCor® system, at the start and end of each treatment period. Compared with placebo, treatment with telmisartan significantly reduced carotid/femoral PWV (mean adjusted treatment difference -0.95 m/s, 95% confidence intervals: -1.67, -0.23 m/s, p=0.013, as well as peripheral and central diastolic, systolic and pulse pressure. In conclusion, the results of this study show that telmisartan is effective in reducing arterial stiffness in hypertensive patients with Type 2 diabetes mellitus, and may potentially have beneficial effects on cardiovascular outcomes, beyond blood-pressure lowering effects, in this patient group.

Mediated moderation or moderated mediation: relationship between length of unemployment, resilience, coping and health.

Science.gov (United States)

Sojo, Víctor; Guarino, Leticia

2011-05-01

The aim of the present research was to evaluate a model of mediated moderation vs. moderated mediation that could explain the relationship between length of unemployment, dispositional resilience, coping styles and depression and social functioning of Venezuelan unemployed individuals. Self-report measures were administered to a sample of 328 unemployed residents in Caracas, Venezuela. Results indicated that emotional coping acted as a mediator in the relationship between resilience and depression. Individuals with greater resilience used more detachment coping when unemployment was longer, while individuals with poorer resilience in the same situation used less avoidance coping. Resilience acted as a protective moderating factor between longer periods of unemployment and social functioning, a process mediated by detachment coping. Overall, results supported a mediated moderation model, with resilience as the moderating factor and coping as the mediator in the relation between stress due to the length of unemployment and well-being.

Effects of high hydrostatic pressure and temperature increase on Escherichia coli spp. and pectin methyl esterase inactivation in orange juice.

Science.gov (United States)

Torres, E F; González-M, G; Klotz, B; Rodrigo, D

2016-03-01

The aim of this study was to evaluate the effect of high hydrostatic pressure treatment combined with moderate processing temperatures (25 ℃-50 ℃) on the inactivation of Escherichia coli O157: H7 (ATCC 700728), E. coli K12 (ATCC 23716), and pectin methyl esterase in orange juice, using pressures of 250 to 500 MPa with times ranging between 1 and 30 min. Loss of viability of E. coli O157:H7 increased significantly as pressure and treatment time increased, achieving a 6.5 log cycle reduction at 400 MPa for 3 min at 25 ℃ of treatment. With regard to the inactivation of pectin methyl esterase, the greatest reduction obtained was 90.05 ± 0.01% at 50 ℃ and 500 MPa of pressure for 15 min; therefore, the pectin methyl esterase enzyme was highly resistant to the treatments by high hydrostatic pressure. The results obtained in this study showed a synergistic effect between the high pressure and moderate temperatures in inactivating E. coli cells. © The Author(s) 2016.

Pressure-induced valence change and moderate heavy fermion state in Eu-compounds

Science.gov (United States)

Honda, Fuminori; Okauchi, Keigo; Sato, Yoshiki; Nakamura, Ai; Akamine, Hiromu; Ashitomi, Yosuke; Hedo, Masato; Nakama, Takao; Takeuchi, Tetsuya; Valenta, Jaroslav; Prchal, Jiri; Sechovský, Vladimir; Aoki, Dai; Ōnuki, Yoshichika

2018-05-01

A pressure-induced valence transition has attracted much attention in Eu-compounds. Among them, EuRh2Si2, EuNi2Ge2, and EuCo2Ge2 reveal the valence transition around 1, 2, and 3 GPa, respectively. We have succeeded in growing single crystals of EuT2X2 (T: transition metal, X: Si, Ge) and studied electronic properties under pressure. EuRh2Si2 indicates a first-order valence transition between 1 and 2 GPa, with a large and prominent hysteresis in the electrical resistivity. At higher pressures, the first-order valence transition changes to a cross-over regime with an intermediate valence state. Tuning of the valence state with pressure is reflected in a drastic change of the temperature dependence of the electrical resistivity in EuRh2Si2 single crystals. Effect of pressure on the valence states on EuRh2Si2, EuIr2Si2, EuNi2Ge2, and EuCo2Ge2, as well as an isostructural related compound EuGa4, are reviewed.

The beneficial effect of regular endurance exercise training on blood pressure and quality of life in patients with hypertension.

Science.gov (United States)

Tsai, Jen-Chen; Yang, Hung-Yu; Wang, Wei-Hsin; Hsieh, Ming-Hsiung; Chen, Pei-Ti; Kao, Ching-Chiu; Kao, Pai-Feng; Wang, Chia-Hui; Chan, Paul

2004-04-01

Regular aerobic exercise can reduce blood pressure and is recommended as part of the lifestyle modification to reduce high blood pressure and cardiovascular risk. Hypertension itself, or/and pharmacological treatment for hypertension is associated with adverse effects on some aspects of quality of life. This study was performed to evaluate the effects of regular endurance exercise training on quality of life and blood pressure. Patients with mild to moderate hypertension (systolic blood pressure 140-180 or diastolic blood pressure 90-110 mm Hg) were randomized to a moderate-intensity aerobic exercise group training for 3 sessions/week over 10 weeks or to a non-exercising control group. Health-related quality of life was assessed with the Short Form 36-item Health Survey (SF-36) at baseline and after 6 and 10 weeks. In the 102 subjects (47 male, mean age 47 years) who completed the study, reductions in blood pressure in the exercise group at 10 weeks (-13.1/-6.3 mm Hg) were significant (P endurance training improves both blood pressure and quality of life in hypertensive patients and should be encouraged more widely.

Evaluation of hydride blisters in zirconium pressure tube in CANDU reactor

International Nuclear Information System (INIS)

Cheong, Y. M.; Kim, Y. S.; Gong, U. S.; Kwon, S. C.; Kim, S. S.; Choo, K.N.

2000-09-01

When the garter springs for maintaining the gap between the pressure tube and the calandria tube are displaced in the CANDU reactor, the sagging of pressure tube results in a contact to the calandria tube. This causes a temperature difference between the inner and outer surface of the pressure tube. The hydride can be formed at the cold spot of outer surface and the volume expansion by hydride dormation causes the blistering in the zirconium alloys. An incident of pressure tube rupture due to the hydride blisters had happened in the Canadian CANDU reactor. This report describes the theoretical development and models on the formation and growth of hydride blister and some experimental results. The evaluation methodology and non-destructive testing for hydride blister in operating reactors are also described

Evaluation of hydride blisters in zirconium pressure tube in CANDU reactor

Energy Technology Data Exchange (ETDEWEB)

Cheong, Y M; Kim, Y S; Gong, U S; Kwon, S C; Kim, S S; Choo, K N

2000-09-01

When the garter springs for maintaining the gap between the pressure tube and the calandria tube are displaced in the CANDU reactor, the sagging of pressure tube results in a contact to the calandria tube. This causes a temperature difference between the inner and outer surface of the pressure tube. The hydride can be formed at the cold spot of outer surface and the volume expansion by hydride dormation causes the blistering in the zirconium alloys. An incident of pressure tube rupture due to the hydride blisters had happened in the Canadian CANDU reactor. This report describes the theoretical development and models on the formation and growth of hydride blister and some experimental results. The evaluation methodology and non-destructive testing for hydride blister in operating reactors are also described.

The stress analysis evaluation and pipe support layout for pressurizer discharge system

International Nuclear Information System (INIS)

Mao Qing; Wang Wei; Zhang Yixiong

2000-01-01

The author presents the stress analysis and evaluation of pipe layout and support adjustment process for Qinshan phase II pressurizer discharge system. Using PDL-SYSPIPE INTERFACE software, the characteristic parameters of the system are gained from 3-D CAD engineering design software PDL and outputted as the input date file format of special pipe stress analysis program SYSPIPE. Based on that, SYSPIPE program fast stress analysis function is applied in adjusting pipe layout , support layout and support types. According to RCC-M standard, the pipe stress analysis and evaluation under deadweight, internal pressure, thermal expansion, seismic, pipe rupture and discharge loads are fulfilled

CHF experiments of tight pitch lattice rod bundles under PWR pressure condition for development of reduced moderation water reactor

International Nuclear Information System (INIS)

Araya, Fumimasa; Nakatsuka, Toru; Yoritsune, Tsutomu

2002-10-01

In order to improve plutonium utilization, design studies of reduced moderation water reactors which have hard neutron energy spectrum have been carried out at Division of Energy System Research of Japan Atomic Energy Research Institute (JAERI). At present, triangle, tight pitch lattice cores with about 1 mm gap width between fuel rods have been focused in the neutronic core design. Since a degradation of the heat removal from the fuel rods is worried, an evaluation of heat removal capability i.e. critical heat flux becomes one of important evaluation items in the feasibility study. However, any of published data base, which can be applicable to the evaluation on such narrow gap width cores, does not exist. Therefore, in the present study, in order to accumulate applicable data and to confirm applicability of an evaluation methodology of critical heat flux, basic experiments on the critical heat flux were performed using the test sections consisted of 7 heater rods bundles with the gap widths of 1.5, 1.0 and 0.6 mm under the PWR pressure conditions. The present report describes the experimental apparatus, experimental conditions and accumulated data. Analysis results of the data and the applicability of the evaluation methodology used for the design work are also discussed in this report. As the results of the experiment, it was found that the critical heat flux increased as the mass flux and the inlet subcooling increased. In the region of the mass flux less than about 2,000 kg/m 2 /s, the critical heat flux decreased as the gap width decreased. In the larger mass flux region, obvious trend of effects of the gap width on critical heat flux were not observed due to data scatterings. The flow-area-averaged thermal-equilibrium quality at the CHF position was in the higher ranges from 0.3 to 0.8 in the cases of gap widths of 1.0 and 0.6 mm, and 0.1 to 0.3 in the 1.5 mm case. Based on the experimental results such that the CHFs occurred in the higher quality range and

Application of hydrogen water chemistry to moderate corrosive circumstances around the reactor pressure vessel bottom of boiling water reactors

International Nuclear Information System (INIS)

Uchida, Shunsuke; Ibe, Eishi; Nakata, Kiyatomo; Fuse, Motomasa; Ohsumi, Katsumi; Takashima, Yoshie

1995-01-01

Many efforts to preserve the structural integrity of major piping, components, and structures in a boiling water reactor (BWR) primary cooling system have been directed toward avoiding intergranular stress corrosion cracking (IGSCC). Application of hydrogen water chemistry (HWC) to moderate corrosive circumstances is a promising approach to preserve the structural integrity during extended lifetimes of BWRs. The benefits of HWC application are (a) avoiding the occurrence of IGSCC on structural materials around the bottom of the crack growth rate, even if microcracks are present on the structural materials. Several disadvantage caused by HWC are evaluated to develop suitable countermeasures prior to HWC application. The advantages and disadvantages of HWC are quantitatively evaluated base on both BWR plant data and laboratory data shown in unclassified publications. Their trade-offs are discussed, and suitable applications of HWC are described. It is concluded that an optimal amount of Hydrogen injected into the feedwater can moderate corrosive circumstances, in the region to be preserved, without serious disadvantages. The conclusions have been drawn by combining experimental and theoretical results. Experiments in BWR plants -- e.g., direct measurements of electrochemical corrosion potential and crack growth rate at the RPV bottom -- are planned that would collect data to support the theoretical considerations

Students' Scientific Epistemic Beliefs, Online Evaluative Standards, and Online Searching Strategies for Science Information: The Moderating Role of Cognitive Load Experience

Science.gov (United States)

Hsieh, Ya-Hui; Tsai, Chin-Chung

2014-06-01

The purpose of this study is to examine the moderating role of cognitive load experience between students' scientific epistemic beliefs and information commitments, which refer to online evaluative standards and online searching strategies. A total of 344 science-related major students participated in this study. Three questionnaires were used to ascertain the students' scientific epistemic beliefs, information commitments, and cognitive load experience. Structural equation modeling was then used to analyze the moderating effect of cognitive load, with the results revealing its significant moderating effect. The relationships between sophisticated scientific epistemic beliefs and the advanced evaluative standards used by the students were significantly stronger for low than for high cognitive load students. Moreover, considering the searching strategies that the students used, the relationships between sophisticated scientific epistemic beliefs and advanced searching strategies were also stronger for low than for high cognitive load students. However, for the high cognitive load students, only one of the sophisticated scientific epistemic belief dimensions was found to positively associate with advanced evaluative standard dimensions.

The high moderating ratio reactor using 100% MOX reloads

International Nuclear Information System (INIS)

Barbrault, P.

1994-06-01

This report presents the concept of a High Moderating ratio Reactor, which should accept 100% MOX reloads. This reactor aims to be the plutonium version of the European Pressurized Reactor (EPR), which is developed jointly by French and German companies. A moderating ration of 2.5 (instead of the standard value of 2.0) is obtained by replacing several fuel rods by water holes. The core would contain 241 Fuel Assemblies. We present some advantages of over-moderation for plutonium fuel, a description of the core and assemblies, calculations of fuel reload schemes and Reactivity Shutdown Margins, and the behavior of the core during two occidental transients. (author). 2 refs., 9 figs., 2 tabs

Design and evaluation of a pressure sensor for high temperature nuclear application

International Nuclear Information System (INIS)

Yancey, M.E.

1981-11-01

The goal of this technical development task was the development of a small eddy-current pressure sensor for use within a high temperature nuclear environment. The sensor is designed for use at pressures and temperatures of up to 17.23 MPa and 650 0 F. The design of the sensor incorporated features to minimize possible errors due to temperature transients present in nuclear applications. This report describes a prototype pressure sensor that was designed, the associated 100 kHz signal conditioning electronics, and the evaluation tests which were conducted

Assessment of Loss-of-Coolant Effect on Pressurized Heavy Water Reactors

International Nuclear Information System (INIS)

Kim, Won Young; Park, Joo Hwan; Kim, Bong Ghi

2009-01-01

A CANDU reactor is a heavy-water-moderated, natural uranium fuelled reactor with a pressure tube. The reactor contains a horizontal cylindrical vessel (calandria) and each pressure tube is isolated from the heavy-water moderator in a calandria. This allows the moderator system to be operated of a high-pressure and of a high-temperature coolant in pressure tube. This causes the pressurized liquid coolant in the channel to void and therefore give rise to a reactivity transient in the event of a break or fault in the coolant circuit. In particular, all CANDU reactors are well known to have a positive void reactivity coefficient and thus this phenomenon may lead to a positive feedback, which can cause a large power pulse. We assess the loss-of-coolant effect by coolant void reactivity versus fuel burnup, four factor parameters for fresh fuel and equilibrium fuel, reactivity change due to the change of coolant density and reactivity change in the case of half- and full-core coolant

Negative Attitudes toward Older Workers and Hiring Decisions: Testing the Moderating Role of Decision Makers' Core Self-Evaluations.

Science.gov (United States)

Fasbender, Ulrike; Wang, Mo

2016-01-01

Organizational hiring practices have been charged for unfair treatment on the grounds of age. Drawing on theories of planned behavior and core self-evaluations, this research investigated the impact of negative attitudes toward older workers on hiring decisions and examined the moderating role of decision-makers' core self-evaluations. We tested our hypotheses based on a structured online questionnaire and a vignette study using a sample of 102 participants working in human resource management across different industries. As predicted, negative attitudes toward older workers were positively related to avoidance of hiring older people, which in turn was negatively related to the likelihood to select the oldest candidate. Because hiring decisions are not only about the hiring subject but also about the decision-maker, we tested the moderating role of decision-makers' core self-evaluations. Results showed that core self-evaluations buffered the relationship between negative attitudes toward older workers and avoidance of hiring older people. Theoretical implications of the findings with regard to hiring decisions about older people and practical recommendations to improve diversity management strategies and age-balanced hiring practices in organizations are discussed.

Evaluation of anticipatory signal to steam generator pressure control program for 700 MWe Indian pressurized heavy water reactor

International Nuclear Information System (INIS)

Pahari, S.; Hajela, S.; Rammohan, H. P.; Malhotra, P. K.; Ghadge, S. G.

2012-01-01

700 MWe Indian Pressurized Heavy Water Reactor (IPHWR) is horizontal channel type reactor with partial boiling at channel outlet. Due to boiling, it has a large volume of vapor present in the primary loops. It has two primary loops connected with the help of pressurizer surge line. The pressurizer has a large capacity and is partly filled by liquid and partly by vapor. Large vapor volume improves compressibility of the system. During turbine trip or load rejection, pressure builds up in Steam Generator (SG). This leads to pressurization of Primary Heat Transport System (PHTS). To control pressurization of SG and PHTS, around 70% of the steam generated in SG is dumped into the condenser by opening Condenser Steam Dump Valves (CSDVs) and rest of the steam is released to the atmosphere by opening Atmospheric Steam Discharge Valves (ASDVs) immediately after sensing the event. This is accomplished by adding anticipatory signal to the output of SG pressure controller. Anticipatory signal is proportional to the thermal power of reactor and the proportionality constant is set so that SG pressure controller's output jacks up to ASDV opening range when operating at 100% FP. To simulate this behavior for 700 MWe IPHWR, Primary and secondary heat transport system is modeled. SG pressure control and other process control program have also been modeled to capture overall plant dynamics. Analysis has been carried out with 3-D neutron kinetics coupled thermal hydraulic computer code ATMIKA.T to evaluate the effect of the anticipatory signal on PHT pressure and over all plant dynamics during turbine trip in 700 MWe IPHWR. This paper brings out the results of the analysis with and without considering anticipatory signal in SG pressure control program during turbine trip. (authors)

Is Familiarity a Moderator of Brand/Country Alliances?

DEFF Research Database (Denmark)

Kristensen, Tore; Gabrielsen, Gorm; Jaffe, Eugene D.

2014-01-01

Product and brand familiarity have an important role in consumer choice behaviour and they have been equated with knowledge and experience Consumers having high and low familiarity utilized brand information (an extrinsic cue) in their evaluations, whereas moderately familiar consumers used...... intrinsic cues (product attributes) in evaluating products. The question of whether familiarity moderates the country-of-origin (COO) effect is a valid one. In this present paper, we attempt to provide additional evidence as to how familiarity with products, brands and countries moderates consumer...... evaluation of brand/country alliances. Specifically, we concentrate on the brand leveraging process identified by Keller (2003) applied to the effect of familiarity on country/brand alliances....

OpenFOAM Analysis of CANDU-6 Moderator Flow

International Nuclear Information System (INIS)

Kim, Hyoung Tae; Chang, Se-Myong

2015-01-01

In this study OpenFOAM (Open Field Operation and Manipulation), an open source CFD solver, is used to simulate the three-dimensional moderator flow in calandria tank of CANDU-6 reactor improving the computational efficiency by parallel computing which does not need any proprietary license. A prototype of CANDU-6 reactor is numerically analyzed about three-dimensional moderator flow in calandrian tank with OpenFOAM, an open source CFD code. The horizontal fuel channels in a CANDU-6 reactor (a pressurized heavy water reactor) are submerged in the heavy water (D 2 O) pool which is contained by a cylindrical tank, calandria. Each fuel channel consists of concentric tubes: a Pressure Tube (PT) and a Calandria Tube (CT). And the CO 2 gas is filled between these tubes. Consequently, a heat flux is rapidly transferred to the outer CT so that a film boiling may occur in CT. As a result, it is important to keep the subcooling in the moderator. It is one of the major concerns in the CANDU safety analyses to estimate the local subcooling margin of the moderator inside the calandria tank. Previous experimental studies showed that the film boiling would be unlikely to occur if the local moderator subcooling is sufficient. Therefore, an accurate prediction of the moderator temperature distribution in the calandria tank is needed to confirm the channel integrity. There have been numerous computational efforts to estimate the thermal hydraulics in the calandria tank using CFD codes. Hadaller et al. obtained a tube bank pressure drop model for tube bundle region of the calandria tank and implemented it into the MODTURC C LAS code. Yoon et al. used the CFX code to develop a CFD model with a porous media approach for the core region. However, it is known that porous media modeling provide only average values of flow velocities and temperatures and do not give any information about local flow variables near tube solid walls, which are necessary to implement accurate heat transfer

OpenFOAM Analysis of CANDU-6 Moderator Flow

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyoung Tae [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Chang, Se-Myong [Kunsan National University, Gunsan (Korea, Republic of)

2015-10-15

In this study OpenFOAM (Open Field Operation and Manipulation), an open source CFD solver, is used to simulate the three-dimensional moderator flow in calandria tank of CANDU-6 reactor improving the computational efficiency by parallel computing which does not need any proprietary license. A prototype of CANDU-6 reactor is numerically analyzed about three-dimensional moderator flow in calandrian tank with OpenFOAM, an open source CFD code. The horizontal fuel channels in a CANDU-6 reactor (a pressurized heavy water reactor) are submerged in the heavy water (D{sub 2}O) pool which is contained by a cylindrical tank, calandria. Each fuel channel consists of concentric tubes: a Pressure Tube (PT) and a Calandria Tube (CT). And the CO{sub 2} gas is filled between these tubes. Consequently, a heat flux is rapidly transferred to the outer CT so that a film boiling may occur in CT. As a result, it is important to keep the subcooling in the moderator. It is one of the major concerns in the CANDU safety analyses to estimate the local subcooling margin of the moderator inside the calandria tank. Previous experimental studies showed that the film boiling would be unlikely to occur if the local moderator subcooling is sufficient. Therefore, an accurate prediction of the moderator temperature distribution in the calandria tank is needed to confirm the channel integrity. There have been numerous computational efforts to estimate the thermal hydraulics in the calandria tank using CFD codes. Hadaller et al. obtained a tube bank pressure drop model for tube bundle region of the calandria tank and implemented it into the MODTURC{sub C}LAS code. Yoon et al. used the CFX code to develop a CFD model with a porous media approach for the core region. However, it is known that porous media modeling provide only average values of flow velocities and temperatures and do not give any information about local flow variables near tube solid walls, which are necessary to implement accurate heat

Evaluation of the Stress Adjustment and Adaptation Model among Families Reporting Economic Pressure

Science.gov (United States)

Vandsburger, Etty; Biggerstaff, Marilyn A.

2004-01-01

This research evaluates the Stress Adjustment and Adaptation Model (double ABCX model) examining the effects resiliency resources on family functioning when families experience economic pressure. Families (N = 128) with incomes at or below the poverty line from a rural area of a southern state completed measures of perceived economic pressure,…

The Impact of Green Supply Chain Management Practices on Performance: Moderating Role of Institutional Pressure with Mediating Effect of Green Innovation

Directory of Open Access Journals (Sweden)

Muhammad Shafique

2017-06-01

Full Text Available Green supply chain management (GSCM, a cross-disciplinary field has grown during recent years with increasing interest from both academia and industry. GSCM considers emphasizing environmental issues in Traditional Supply Chain Management (TSCM. Due to the new trends in global warming, environmental sustainability has become a greater concern among the organizations and enterprises globally. This study will focus on green supply chain management practices in the presence of green innovation. Green innovation will improve organizational processes as well as products, which lead to economic and environmental performance. Different institutional actors are putting pressures to implement Green supply chain management practices. Population of this study is electronics industry in Pakistan. Sample size is 500 with cluster sampling technique. Data has been collected through a survey method based on the adopted questionnaire. The collected data will be tested through Cronbach Alpha, Descriptive Statistics, Pearson Correlation, Linear Regression, Moderated Regression, Multiple Logistic Regression and Hayes’s statistical tests to analyse the suggested research model. This study will enable organizations to implement green supply chain management practices to bear institutional pressure and move towards green innovation to enhance their economic and environmental performance that were never possible before this study.

Thermal-hydraulic instabilities in pressure tube graphite - moderated boiling water reactors

Energy Technology Data Exchange (ETDEWEB)

Tsiklauri, G.; Schmitt, B.

1995-09-01

Thermally induced two-phase instabilities in non-uniformly heated boiling channels in RBMK-1000 reactor have been analyzed using RELAP5/MOD3 code. The RELAP5 model of a RBMK-1000 reactor was developed to investigate low flow in a distribution group header (DGH) supplying 44 fuel pressure tubes. The model was evaluated against experimental data. The results of the calculations indicate that the period of oscillation for the high power tube varied from 3.1s to 2.6s, over the power range of 2.0 MW to 3.0 MW, respectively. The amplitude of the flow oscillation for the high powered tube varied from +100% to -150% of the tube average flow. Reverse flow did not occur in the lower power tubes. The amplitude of oscillation in the subcooled region at the inlet to the fuel region is higher than in the saturated region at the outlet. In the upper fuel region and outlet connectors the flow oscillations are dissipated. The threshold of flow instability for the high powered tubes of a RBMK reactor is compared to Japanese data and appears to be in good agreement.

Thermal-hydraulic instabilities in pressure tube graphite-moderated boiling water reactors

International Nuclear Information System (INIS)

Tsiklauri, G.; Schmitt, B.

1995-09-01

Thermally induced two-phase instabilities in non-uniformly heated boiling charmers in RBMK-1000 reactor have been analyzed using RELAP5/MOD3 code. The RELAP5 model of a RBMK-1000 reactor was developed to investigate low flow in a distribution group header (DGH) supplying 44 fuel pressure tubes. The model was evaluated against experimental data. The results of the calculations indicate that the period of oscillation for the high power tube varied from 3.1s to 2.6s, over the power range of 2.0 MW to 3.0 MW, respectively. The amplitude of the flow oscillation for the high powered tube varied from +100% to -150% of the tube average flow. Reverse flow did not occur in the lower power tubes. The amplitude of oscillation in the subcooled region at the inlet to the fuel region is higher than in the saturated region at the outlet. In the upper fuel region and outlet connectors the flow oscillations are dissipated. The threshold of flow instability for the high powered tubes of a RBMK reactor is compared to Japanese data and appears to be in good agreement

Effect of combined loading due to bending and internal pressure on pipe flaw evaluation criteria

International Nuclear Information System (INIS)

Miura, Naoki; Sakai, Shinsuke

2006-01-01

Considering a rational maintenance rule of Light Water Reactor piping, reliable flaw evaluation criteria are essential to determine how a detected flaw is detrimental to continuous plant operation. Ductile fracture is one of the dominant failure modes to be considered for carbon steel piping, and can be analyzed by the elastic-plastic fracture mechanics. Some analytical efforts have been provided as flaw evaluation criteria using load correction factors such like the Z-factors in the JSME codes on fitness-for-service for nuclear power plants or the ASME boiler and pressure vessel code section XI. The present correction factors were conventionally determined taken conservatism and simplicity into account, however, the effect of internal pressure which would be an important factor under an actual plant condition was not adequately considered. Recently, a J-estimation scheme, 'LBB. ENGC' for ductile fracture analysis of circumferentially through-wall-cracked pipes subjected combined loading was newly developed to have a better prediction with more realistic manner. This method is explicitly incorporated the contribution of both bending and tension due to internal pressure by means of the scheme compatible with an arbitrary combined loading history. In this paper, the effect of internal pressure on the flaw evaluation criteria was investigated using the new J-estimation scheme. A correction factor based on the new J-estimation scheme was compared with the present correction factors, and the predictability of the current flaw evaluation criteria was quantitatively evaluated in consideration of internal pressure. (author)

Does CPAP treatment lead to gastroesophageal reflux in patients with moderate and severe OSA?

Science.gov (United States)

Ozcelik, Hatice; Kayar, Yusuf; Danalioglu, Ahmet; Arabaci, Elif; Uysal, Omer; Yakar, Fatih; Kart, Levent

2017-03-01

Obstructive sleep apnea (OSA) leads to upper respiratory tract obstruction, causing increased abdominal-gastric pressure and decreased lower esophageal sphincter (LES) pressure and thus gastroesophageal reflux (GER). Continuous positive airway pressure (CPAP) is known to be an effective method for OSA treatment, but its effect on GER is still controversial. There are a very few studies investigating CPAP and GER relationship and performed based on pre- and post-treatment objective parameters of GER in patients with OSA. The study investigated the effect of CPAP treatment in patients with moderate and severe OSA without GER complaints on pre- and post-treatment objective GER parameters. The study included 25 patients with respiratory disturbance indices >15 without reflux symptoms who had undergone polysomnography at sleep laboratory. Age, sex, body mass index (BMI), waist, and neck circumference of the patients were documented. DeMeester score, LES pressure, and polysomnography parameters were evaluated pre- and post-CPAP. The results were statistically evaluated, and p value CPAP phase, mean sphincter pressure was 22.2 ± 1.2 (range 8-73), and mean DeMeester score was 18 ± 15.5 (range 0.2-57). At the post-CPAP, mean sphincter pressure was 22.9 ± 1.6 (range 9-95), and mean DeMeester score was 16.3 ± 14.8 (range 0.2-55). No significant difference (p > 0.05) was found comparing pre-CPAP and post-CPAP measurements. Objective criteria show that CPAP treatment does not cause reflux in patients with OSA. Unlike studies reported in the literature, this conclusion has been reached by pre- and post-CPAP assessments.

Evaluation of flaws or service induced cracks in pressure vessels

International Nuclear Information System (INIS)

Riccardella, P.C.; Copeland, J.F.; Gilman, J.

1987-01-01

An overview of the ASME flaw evaluation procedures for nuclear pressure vessels is presented, with emphasis on fatigue crack growth evaluations. Environmental and load-rate effects are further considered with respect to new crack growth data and a time-dependent crack growth model. This new crack growth model is applied to evaluate feedwater nozzle cracking in boiling water reactors and is compared to current and past ASME crack growth curves. The time-dependent model bounds the observed cracking and indicates that more detailed consideration of material susceptibility, in terms of sulfur content and product form, is needed

Evaluation of response function of moderating-type neutron detector and application to environmental neutron measurement

International Nuclear Information System (INIS)

Kosako, Toshiso; Nakamura, Takashi; Iwai, Satoshi; Katsuki, Shinji; Kamata, Masashi.

1983-08-01

The energy-dependent response function of a multi-cylinder moderating-type BF 3 counter, so-called Bonner counter, was calculated by the time-dependent multi-group Monte Carlo code, TMMCR. The calculated response function was evaluated experimentally for neutron energy below about 50 keV down to epithermal energy by the time-of-flight method combining with a large lead pile at the Nuclear Engineering Research Laboratory, University of Tokyo and also above 50 keV by using the monoenergetic neutron standard field a t the Electrotechnical Laboratory. The time delay in the polyethylene moderator of the Bonner counter due to multiple collisions with hydrogen was analyzed by the TMMCR code and used for the time-spectrum analysis of the time-of-flight measurement. The response function obtained by these two experiments showed good agreement with the calculated results. This Bonner counter having a response function evaluated from thermal to MeV energy range was used for spectrometry and dosimetry of environmental neutrons around some nuclear facilities. The neutron spectra and dose measured in the environment around a 252 Cf fission source, fast neutron source reactor and electron synchrotron were all in good agreement with the calculated results and the measured results with other neutron detectors. (author)

Effect of moderate exercise on peritoneal neutrophils from juvenile rats.

Science.gov (United States)

Braz, Glauber Ruda; Ferreira, Diorginis Soares; Pedroza, Anderson Apolonio; da Silva, Aline Isabel; Sousa, Shirley Maria; Pithon-Curi, Tania Cristina; Lagranha, Claudia

2015-09-01

Previous studies showed that moderate exercise in adult rats enhances neutrophil function, although no studies were performed in juvenile rats. We evaluated the effects of moderate exercise on the neutrophil function in juvenile rats. Viability and neutrophils function were evaluated. Moderate exercise did not impair the viability and mitochondrial transmembrane potential of neutrophils, whereas there was greater reactive oxygen species production (164%; p < 0.001) and phagocytic capacity (29%; p < 0.05). Our results suggest that moderate exercise in juvenile rats improves neutrophil function, similar to adults.

Evaluation to Mitigate Secondary System Peak Pressure for Loss of Condenser Vacuum Event

Energy Technology Data Exchange (ETDEWEB)

Choi, Bong Oh; Park, Jong Cheol; Park, Min Soo; Lee, Gyu Cheon; Kim, Shin Whan [KEPCO E and C, Inc., Daejeon (Korea, Republic of)

2015-10-15

In this paper, countermeasures to compensate the increased secondary pressure are introduced and evaluated. From the standpoint of the secondary system pressurization, consideration of the PPCS may result in a conservative secondary system peak pressure. The control systems are generally credited for the safety analysis if the analysis produces conservative results. However, in most of all non-loss of coolant accident (non-LOCA) events, the control system helps to mitigate a transient state. Accordingly, the safety analysis of non-LOCA assumes the control systems are in the manual mode of operation. The loss of condenser vacuum event (LOCV) is a typical anticipated operational occurrence (AOO) which results in an increase in primary and secondary system pressure. The pressurizer (PZR) pressure control system (PPCS) will function to reduce the primary system pressure increase during the transient. Therefore, it is assumed to be in manual mode and credit is not taken for its functioning. However, crediting the function of PPCS has been found to be more conservative with regard to the secondary system pressure. This is due to the delay of the reactor trip on high pressurizer pressure (HPP) and results in an increase in secondary pressure.

Emotional Dissonance and Burnout: The Moderating Role of Team Reflexivity and Re-Evaluation.

Science.gov (United States)

Andela, Marie; Truchot, Didier

2017-08-01

The aim of the present study was to better understand the relationship between emotional dissonance and burnout by exploring the buffering effects of re-evaluation and team reflexivity. The study was conducted with a sample of 445 nurses and healthcare assistants from a general hospital. Team reflexivity was evaluated with the validation of the French version of the team reflexivity scale (Facchin, Tschan, Gurtner, Cohen, & Dupuis, 2006). Burnout was measured with the MBI General Survey (Schaufeli, Leiter, Maslach, & Jackson, 1996). Emotional dissonance and re-evaluation were measured with the scale developed by Andela, Truchot, & Borteyrou (2015). With reference to Rimé's theoretical model (2009), we suggested that both dimensions of team reflexivity (task and social reflexivity) respond to both psychological necessities induced by dissonance (cognitive clarification and socio-affective necessities). Firstly, results indicated that emotional dissonance was related to burnout. Secondly, regression analysis confirmed the buffering role of re-evaluation and social reflexivity on the emotional exhaustion of emotional dissonance. Overall, results contribute to the literature by highlighting the moderating effect of re-evaluation and team reflexivity in analysing the relationship between emotional dissonance and burnout. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Molten fuel-moderator interaction

International Nuclear Information System (INIS)

Lee, J.H.S.; Kynstautas, R.

1987-02-01

A critical review of the current understanding of vapor explosions was carried out. It was concluded that, on the basis of actual industrial accidents and large scale experiments, energetic high yield steam explosion cannot be regarded as an improbable event if large quantities of molten fuel and coolant are mixed together. This study also reviewed a hydrodynamic transient model proposed by Henry and Fauske Associates to assess a molten fuel-moderator interaction event. It was found that the proposed model negates a priori the possibility of a violent event, by introducing two assumptions: 1) fine fragmentation of the molten fuel, and ii) rapid heat transfer from the fine fragments to form steam. Using the Hicks and Menzies thermodynamic model, maximum work potential and pressure rise in the calandria were estimated. However, it is recommended that a more representative upper bound model based on an underwater explosion of a pressurized volume of steam be developed

Heavy water moderated tubular type nuclear reactor

International Nuclear Information System (INIS)

Oohashi, Masahisa.

1986-01-01

Purpose: To enable to effectively change the volume of heavy water per unit fuel lattice in heavy water moderated pressure tube type nuclear reactors. Constitution: In a nuclear reactor in which fuels are charged within pressure tubes and coolants are caused to flow between the pressure tubes and the fuels, heavy water tubes for recycling heavy water are disposed to a gas region formed to the outside of the pressure tubes. Then, the pressure tube diameter at the central portion of the reactor core is made smaller than that at the periphery of the reactor core. Further, injection means for gas such as helium is disposed to the upper portion for each of the heavy water tubes so that the level of the heavy water can easily be adjusted by the control for the gas pressure. Furthermore, heavy water reflection tubes are disposed around the reactor core. In this constitution, since the pitch for the pressure tubes can be increased, the construction and the maintenance for the nuclear reactor can be facilitated. Also, since the liquid surface of the heavy water in the heavy water tubes can be varied, nuclear properties is improved and the conversion ratio is improved. (Ikeda, J.)

Thermally moderated hollow fiber sorbent modules in rapidly cycled pressure swing adsorption mode for hydrogen purification

KAUST Repository

Lively, Ryan P.; Bessho, Naoki; Bhandari, Dhaval A.; Kawajiri, Yoshiaki; Koros, William J.

2012-01-01

We describe thermally moderated multi-layered pseudo-monolithic hollow fiber sorbents entities, which can be packed into compact modules to provide small-footprint, efficient H2 purification/CO2 removal systems for use in on-site steam methane reformer product gas separations. Dual-layer hollow fibers are created via dry-jet, wet-quench spinning with an inner "active" core of cellulose acetate (porous binder) and zeolite NaY (69 wt% zeolite NaY) and an external sheath layer of pure cellulose acetate. The co-spun sheath layer reduces the surface porosity of the fiber and was used as a smooth coating surface for a poly(vinyl-alcohol) post-treatment, which reduced the gas permeance through the fiber sorbent by at least 7 orders of magnitude, essentially creating an impermeable sheath layer. The interstitial volume between the individual fibers was filled with a thermally-moderating paraffin wax. CO2 breakthrough experiments on the hollow fiber sorbent modules with and without paraffin wax revealed that the "passively" cooled paraffin wax module had 12.5% longer breakthrough times than the "non-isothermal" module. The latent heat of fusion/melting of the wax offsets the released latent heat of sorption/desorption of the zeolites. One-hundred rapidly cycled pressure swing adsorption cycles were performed on the "passively" cooled hollow fiber sorbents using 25 vol% CO2/75 vol% He (H2 surrogate) at 60 °C and 113 psia, resulting in a product purity of 99.2% and a product recovery of 88.1% thus achieving process conditions and product quality comparable to conventional pellet processes. Isothermal and non-isothermal dynamic modeling of the hollow fiber sorbent module and a traditional packed bed using gPROMS® indicated that the fiber sorbents have sharper fronts (232% sharper) and longer adsorbate breakthrough times (66% longer), further confirming the applicability of the new fiber sorbent approach for H2 purification. © 2012, Hydrogen Energy Publications, LLC

Thermally moderated hollow fiber sorbent modules in rapidly cycled pressure swing adsorption mode for hydrogen purification

KAUST Repository

Lively, Ryan P.

2012-10-01

We describe thermally moderated multi-layered pseudo-monolithic hollow fiber sorbents entities, which can be packed into compact modules to provide small-footprint, efficient H2 purification/CO2 removal systems for use in on-site steam methane reformer product gas separations. Dual-layer hollow fibers are created via dry-jet, wet-quench spinning with an inner "active" core of cellulose acetate (porous binder) and zeolite NaY (69 wt% zeolite NaY) and an external sheath layer of pure cellulose acetate. The co-spun sheath layer reduces the surface porosity of the fiber and was used as a smooth coating surface for a poly(vinyl-alcohol) post-treatment, which reduced the gas permeance through the fiber sorbent by at least 7 orders of magnitude, essentially creating an impermeable sheath layer. The interstitial volume between the individual fibers was filled with a thermally-moderating paraffin wax. CO2 breakthrough experiments on the hollow fiber sorbent modules with and without paraffin wax revealed that the "passively" cooled paraffin wax module had 12.5% longer breakthrough times than the "non-isothermal" module. The latent heat of fusion/melting of the wax offsets the released latent heat of sorption/desorption of the zeolites. One-hundred rapidly cycled pressure swing adsorption cycles were performed on the "passively" cooled hollow fiber sorbents using 25 vol% CO2/75 vol% He (H2 surrogate) at 60 °C and 113 psia, resulting in a product purity of 99.2% and a product recovery of 88.1% thus achieving process conditions and product quality comparable to conventional pellet processes. Isothermal and non-isothermal dynamic modeling of the hollow fiber sorbent module and a traditional packed bed using gPROMS® indicated that the fiber sorbents have sharper fronts (232% sharper) and longer adsorbate breakthrough times (66% longer), further confirming the applicability of the new fiber sorbent approach for H2 purification. © 2012, Hydrogen Energy Publications, LLC

Evaluation of four non-invasive methods for examination and characterization of pressure ulcers

DEFF Research Database (Denmark)

Andersen, E.S.; Karlsmark, T.

2008-01-01

Background: Pressure ulcers are globally of major concern and there is need for research in the pathogenesis for early intervention. Early studies have suggested existence of a hypo-echogenic subepidermal layer at the location of pressure ulcers, visualized by ultrasound scans. As a continuation......, we here report on usability of four non-invasive techniques for evaluation of pressure ulcers. Methods: Fifteen pressure ulcers in stage 0-IV were examined using four different non-invasive techniques [redness index, skin temperature, skin elasticity (i.e. retraction time), and ultrasound scanning...... at all pressure ulcers, but none at the reference points. The skin retraction time was often higher at the location of a pressure ulcer than at the reference location. We found no correlation between the stage of the ulcers and temperature, redness index, subepidermal layer thickness, or retraction time...

Investigation of focused and unfocused transducer beam patterns in moderately nonlinear absorbing media

Science.gov (United States)

Kharin, Nikolay A.

2001-05-01

The novel solution of the KZK equation for acoustic pressure of the second harmonic in slightly focused beam of a circular transducer was obtained in a closed form for moderately nonlinear absorbing media (Gol'dberg numbers ~ 1). The solution is based on the method of slowly changing wave profile in combination with the method of successive approximations. Two pairs of transducers (Valpey-Fisher Corp.) Were compared to investigate the influence of focusing on the applicability of the moderate nonlinearity approach. The first pair was of 0.25' diameter and the second was of 0.5' diameter. Both pairs has one transducer with flat surface and the other geometrically focused at 4'. The central frequency for all transducers was 5 MHz. Measurements were undertaken in the blood-mimicking solution of water and glycerine. The results demonstrated that for slightly focused transducers with circular apertures, the moderate nonlinearity approach is still valid, as it was proved for flat sources with the same source level, despite the higher pressures in the focal region. The peak pressure for the weakly focused system occurs at a shorter range than focal length.

Efficacy and safety of the treatment: combination of benazepril/lercanidipine vs. benazepril alone in patients with mild-to-moderate hypertension.

Science.gov (United States)

Chen, Ting; Chen, Guang-Hui; Yang, Ting-Shu; Zhong, Zhen-Yu; An, Wei-Shuai; Zhang, Xiao-Xia; Li, Jia-Dan

2013-06-01

Combination therapy is an effective method to reduce the blood pressure (BP) for patients with hypertension. This study was performed to evaluate the efficacy and safety of benazepril/lercanidipine compared with benazepril alone in patients with mild-to-moderate hypertension. One hundred and eighty-one patients with mild-to-moderate primary hypertension were assigned in this randomized, single-blind, parallel-group study and were randomly divided into group A (benazepril 10 mg/lercanidipine 10 mg) and group B (benazepril 10 mg) for 8 weeks. At 4 weeks, the dosage of Benazepril was titrated up to 20 mg if the diastolic blood pressure (DBP) remained ≥ 90 mmHg. BP control and side effects were evaluated at the end of 1, 4 and 8 weeks. The baseline characteristics of the two groups were similar. The BP in both groups decreased from the baseline (P Benazepril/Lercanidipine produced greater BP reduction than Benazepril alone (P benazepril/lercanidipine and benazepril groups at the end of 1, 4, and 8 weeks were 41.2% vs. 37.6% (P > 0.05), 67.1% vs. 44.7% (P benazepril/lercanidipine combination is more effective in reducing BP than benazepril alone, while it does not increase the incidence of side effects.

Transient Moderator Simulation Using CFX10-CAMO, a CANDU Moderator Analysis Model Based on a Coupled Solver

International Nuclear Information System (INIS)

Yoon, Churl; Park, Joo Hwan

2007-01-01

When a PHT(Primary Heat Transfer) system fails to remove excess heat from fuel channels for some loss of coolant accidents(LOCA's) in CANDU NPP's, the fuel channel temperature could increase until the pressure tube strains (i.e., balloon or sag) to contact its surrounding Calandria tube.(PT/CT contact) Following a PT/CT contact, there is a spike in the heat flux to the moderator surrounding the Calandria tube, which may lead to a sustained CT dryout and also a failure of a fuel channel. The prevention of a CT dryout following a PT/CT contact depends on the local moderator subcooling. That is, fuel channel integrity depends on the capability of the moderator to act as the ultimate heat sink for some LOCA's in a CANDU reactor. In KAERI, Yoon et al. developed a CFD model for predicting a CANDU-6 moderator temperature on the basis of a commercial CFD code CFX-4(ANSYS Inc.). This analytic model has the strength of modelling the hydraulic resistances in the core region and accounting for a heat source term in the energy equations. But convergence difficulties and a slow computing speed are the limitations of this model, because the CFX-4 code adapts a segregated solver to resolve a moderator circulation including a strong coupled-effect. Compared to a segregated solver, a coupled-solver is highly efficient and robust especially for a flow with a strong interference between the variables such as combustion

Sensitivity of Spores of Eight Bacillus Cereus Strains to Pressure-Induced Germination by Moderate Hydrostatic Pressure, Time and Temperature

National Research Council Canada - National Science Library

Kalchayanand, Norasak; Ray, Bibek; Dunne, C. P; Sikes, Anthony

2005-01-01

The spores of eight Bacillus cereus strains were pressurized at 138 to 483 MPa for 5 to 20 min at 25 to 70 C in order to determine the sensitive and the resistant strains to pressure-induced germination...

Effect of combined loading due to bending and internal pressure on pipe flaw evaluation criteria

International Nuclear Information System (INIS)

Miura, Naoki; Sakai, Shinsuke

2008-01-01

Considering a rule for the rationalization of maintenance of Light Water Reactor piping, reliable flaw evaluation criteria are essential for determining how a detected flaw will be detrimental to continuous plant operation. Ductile fracture is one of the dominant failure modes that must be considered for carbon steel piping and can be analyzed by elastic-plastic fracture mechanics. Some analytical efforts have provided various flaw evaluation criteria using load correction factors, such as the Z-factors in the JSME codes on fitness-for-service for nuclear power plants and the section XI of the ASME boiler and pressure vessel code. The present Z-factors were conventionally determined, taking conservativity and simplicity into account; however, the effect of internal pressure, which is an important factor under actual plant conditions, was not adequately considered. Recently, a J-estimation scheme, LBB.ENGC for the ductile fracture analysis of circumferentially through-wall-cracked pipes subjected to combined loading was developed for more accurate prediction under more realistic conditions. This method explicitly incorporates the contributions of both bending and tension due to internal pressure by means of a scheme that is compatible with an arbitrary combined-loading history. In this study, the effect of internal pressure on the flaw evaluation criteria was investigated using the new J-estimation scheme. The Z-factor obtained in this study was compared with the presently used Z-factors, and the predictability of the current flaw evaluation criteria was quantitatively evaluated in consideration of the internal pressure. (author)

Evaluation of Generalized Performance across Materials When Using Video Technology by Students with Autism Spectrum Disorder and Moderate Intellectual Disability

Science.gov (United States)

Mechling, Linda C.; Ayres, Kevin M.; Foster, Ashley L.; Bryant, Kathryn J.

2015-01-01

The purpose of this study was to evaluate the ability of four high school-aged students with a diagnosis of autism spectrum disorder and moderate intellectual disability to generalize performance of skills when using materials different from those presented through video models. An adapted alternating treatments design was used to evaluate student…

Fracture probability evaluation of a LWR pressure vessel

International Nuclear Information System (INIS)

Grandemange, J.; Pellissier-Tanon, A.; Quero, J.; Carnino, A.; Dufresne, J.

1978-01-01

Fracture probability evaluation, of a LWR pressure vessel have been performed in the past, using statistical data from conventional plant. A more accurate evaluation has been requested in 1976 from the SCSIN to the CEA. With this object, a joint collaboration agreement has been signed between CEA, EURATOM/ISPRA and FRAMATOME. The whole program proceeding from this agreement is managed by a joint board including the three partners. The basic objective of this program is to develop a method which integrates, or makes it possible to integrate at a later stage, the greatest number of significant parameters. Also, in order to prepare the practical applications, a special effort is being made to collect the data corresponding to these parameters. Parallel basic research program have been launched in order to clarify our knowledge on some important parts of the main factors contributing to the evaluation. The results of this research will be progressively introduced into the method or will help checking its validity

Evaluation of blood and serum markers in spinal cord injured patients with pressure sores.

Science.gov (United States)

Gurcay, Eda; Bal, Ajda; Gurcay, Ahmet G; Cakci, Aytul

2009-03-01

To evaluate blood and serum markers in traumatic spinal cord injured (SCI) patients, with and without pressure sores. This cross-sectional study was performed at the Ministry of Health Diskapi Yildirim Beyazit, and Numune Education and Research Hospitals, Ankara, Turkey, from 2006-2008. A total of 23 SCI patients with pressure sores (group I) and a control group of 25 SCI patients without pressure sores (group II) were evaluated. Characteristics of sores were examined with respect to duration, location, grade, tissue types, surface area, and exudate amount. Recorded laboratory parameters included erythrocyte sedimentation rates (ESR), C-reactive protein (CRP), hemoglobin (Hb), hematocrit (Htc), lymphocytes, white blood cells (WBC), red blood cells (RBC), serum iron, transferrin, total iron-binding capacity (TIBC), ferritin, total protein, albumin, vitamin B12, and zinc. The most common pressure sore location was the sacrum (38%). Compared to the control group, the patients with pressure sores showed anemia with reduced serum iron, transferrin, TIBC, and increased ferritin. They also had increased ESR, CRP, and WBC and reduced lymphocytes, total protein, albumin and zinc. Statistically significant correlations were found between CRP, Hb, Htc, lymphocytes, RBC, WBC, and serum protein levels, and grade of pressure sores. Clinicians should regularly screen patients with respect to blood and serum markers, in order to determine any risks for pressure sores, and they should perform immediate preventive measures based on the patient's condition.

Detailed evaluation of RCS boundary rupture during high-pressure severe accident sequences

International Nuclear Information System (INIS)

Park, Rae-Joon; Hong, Seong-Wan

2011-01-01

A depressurization possibility of the reactor coolant system (RCS) before a reactor vessel rupture during a high-pressure severe accident sequence has been evaluated for the consideration of direct containment heating (DCH) and containment bypass. A total loss of feed water (TLOFW) and a station blackout (SBO) of the advanced power reactor 1400 (APR 1400) has been evaluated from an initiating event to a creep rupture of the RCS boundary by using the SCDAP/RELAP5 computer code. In addition, intentional depressurization of the RCS using power-operated safety relief valves (POSRVs) has been evaluated. The SCDAPRELAP5 results have shown that the pressurizer surge line broke before the reactor vessel rupture failure, but a containment bypass did not occur because steam generator U tubes did not break. The intentional depressurization of the RCS using POSRV was effective for the DCH prevention at a reactor vessel rupture. (author)

Improvement of methods to evaluate brittle failure resistance of the WWER reactor pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Popov, A A; Parshutin, E V [Engineering Center of Nuclear Equipment Strength, Research and Development Inst. of Power Engineering, Moscow (Russian Federation); Rogov, M F; Dragunov, U G [Experimenter` s and Designer` s Office ` ` Hydropress` ` (Russian Federation)

1997-09-01

At the next 10 years a number of Russian WWER nuclear power plants will complete its design lifetime. Normative methods to evaluate brittle failure resistance of the reactor pressure vessels used in Russia have been intended for design stage. The evaluation of reactor pressure vessel lifetime in operation stage demands to create new methods of calculation and new methods for experimental evaluation of brittle failure resistance degradation. The main objective of the study in this type of reactor is weldment number 4. In this report an analysis is made of methods to determine critical temperature of reactor materials including the results of instrumented Charpy testing. 12 figs.

Validation of a protocol to evaluate maximal expiratory pressure using a pressure transducer and a signal conditioner

Directory of Open Access Journals (Sweden)

Viviane Soares

2011-09-01

Full Text Available The respiratory muscles can present fatigue and even chronic inability to generate force. So, reliable devices are necessary to their evaluation. The aim of this study is to evaluate the MEP (Maximal Expiratory Pressure values of individuals between 20 and 25 years old and to validate a protocol using a pressure transducer and a signal conditioner comparing it with the digital manometer. We evaluated the MEP of 10 participants. They remained seated and made six respiratory maneuvers from Total Lung Capacity (TLC to Residual Volume (RV. The results in the study showed no statistically significant differences when compared to values reported in the literature, and that the pressure transducer provides reliable values for MEP.Os músculos respiratórios podem apresentar fadiga e até mesmo a incapacidade crônica na geração de força, sendo necessários dispositivos confiáveis para sua avaliação. O objetivo deste estudo foi avaliar a pressão expiratória máxima (PeMáx de indivíduos entre 20 e 25 anos e validar um protocolo que utiliza um transdutor de pressão e um condicionador de sinais comparando-o com a manovacuometria. Foram avaliadas a PeMáx de 10 participantes. Estes permaneceram sentados e realizaram seis manobras respiratórias a partir da capacidade pulmonar total (CPT até o volume residual (VR. Os resultados do estudo não apresentaram diferenças estatisticamente significativas quando comparados com os valores de normalidade descritos na literatura e mostraram que o transdutor de pressão fornece valores confiáveis para Pe máx.

Consequence evaluation of hypothetical reactor pressure vessel support failure

International Nuclear Information System (INIS)

Lu, S.C.; Holman, G.S.; Lambert, H.E.

1991-01-01

This paper describes a consequence evaluation to address safety concerns raised by the radiation embrittlement of the reactor pressure vessel (RPV) supports for the Trojan nuclear power plant. The study comprises a structural evaluation and an effects evaluation and assumes that all four reactor vessel supports have completely lost the load carrying capability. The structural evaluation concludes that the Trojan reactor coolant loop (RCL) piping is capable of transferring loads to the steam generator (SG) supports and the reactor coolant pump (RCP) supports and that the SG supports and the RCP supports have sufficient design margins to accommodate additional loads transferred to them through the RCL piping. The effects evaluation, employing a systems analysis approach, investigates initiating events and the reliability of the engineered safeguard systems as the RPV is subject to movements caused by the RPV support failure. The evaluation identifies a number of areas for further investigation and concludes that a hypothetical failure of the Trojan RPV supports due to radiation embrittlement will not result in consequences of significant safety concerns. (author)

Salinity-gradient power: Evaluation of pressure-retarded osmosis and reverse electrodialysis

NARCIS (Netherlands)

Post, J.W.; Veerman, J.; Hamelers, H.V.M.; Euverink, G.J.W.; Metz, S.J.; Nymeijer, K.; Buisman, C.J.N.

2007-01-01

A huge potential to obtain clean energy exists from mixing water streams with different salt concentrations. Two membrane-based energy conversion techniques are evaluated: pressure-retarded osmosis and reverse electrodialysis. From the literature, a comparison is not possible since the reported

Cardiopulmonary Changes with Moderate Decompression in Rats

Science.gov (United States)

Robinson, R.; Little, T.; Doursout, M.-F.; Butler, B. D.; Chelly, J. E.

1996-01-01

Sprague-Dawley rats were compressed to 616 kPa for 120 min then decompressed at 38 kPa/min to assess the cardiovascular and pulmonary responses to moderate decompression stress. In one series of experiments the rats were chronically instrumented with Doppler ultrasonic probes for simultaneous measurement of blood pressure, cardiac output, heart rate, left and right ventricular wall thickening fraction, and venous bubble detection. Data were collected at base-line, throughout the compression/decompression protocol, and for 120 min post decompression. In a second series of experiments the pulmonary responses to the decompression protocol were evaluated in non-instrumented rats. Analyses included blood gases, pleural and bronchoalveolar lavage (BAL) protein and hemoglobin concentration, pulmonary edema, BAL and lung tissue phospholipids, lung compliance, and cell counts. Venous bubbles were directly observed in 90% of the rats where immediate post-decompression autopsy was performed and in 37% using implanted Doppler monitors. Cardiac output, stroke volume, and right ventricular wall thickening fractions were significantly decreased post decompression, whereas systemic vascular resistance was increased suggesting a decrease in venous return. BAL Hb and total protein levels were increased 0 and 60 min post decompression, pleural and plasma levels were unchanged. BAL white blood cells and neutrophil percentages were increased 0 and 60 min post decompression and pulmonary edema was detected. Venous bubbles produced with moderate decompression profiles give detectable cardiovascular and pulmonary responses in the rat.

Evaluation of Peripheral Blood Circulation Disorder in Scleroderma Patients Using an Optical Sensor with a Pressurization Mechanism.

Directory of Open Access Journals (Sweden)

Yoshiki Yamakoshi

Full Text Available Blood circulation function of peripheral blood vessels in skin dermis was evaluated employing an optical sensor with a pressurization mechanism using the blood outflow and reflow characteristics. The device contains a light source and an optical sensor. When applied to the skin surface, it first exerts the primary pressure (higher than the systolic blood pressure, causing an outflow of blood from the dermal peripheral blood vessels. After two heartbeats, the pressure is lowered (secondary pressure and blood reflows into the peripheral blood vessels. Hemoglobin concentration, which changes during blood outflow and reflow, is derived from the received light intensity using the Beer-Lambert law. This method was evaluated in 26 healthy female volunteers and 26 female scleroderma patients. In order to evaluate the blood circulation function of the peripheral blood vessels of scleroderma patients, pressurization sequence which consists of primary pressure followed by secondary pressure was adopted. Blood reflow during the first heartbeat period after applying the secondary pressure of 40mmHg was (mean±SD 0.059±0.05%mm for scleroderma patients and 0.173±0.104%mm for healthy volunteers. Blood reflow was significantly lower in scleroderma patients than in healthy volunteers (p<0.05. This result indicates that the information necessary for assessing blood circulation disorder of peripheral blood vessels in scleroderma patients is objectively obtained by the proposed method.

Pressure Tube and Pressure Vessel Reactors; certain comparisons

Energy Technology Data Exchange (ETDEWEB)

Margen, P H; Ahlstroem, P E; Pershagen, B

1961-04-15

In a comparison between pressure tube and pressure vessel type reactors for pressurized D{sub 2}O coolant and natural uranium, one can say that reactors of these two types having the same net electrical output, overall thermal efficiency, reflected core volume and fuel lattice have roughly the same capital cost. In these circumstances, the fuel burn-up obtainable has a significant influence on the relative economics. Comparisons of burn-up values made on this basis are presented in this report and the influence on the results of certain design assumptions are discussed. One of the comparisons included is based on the dimensions and ratings proposed for CANDU. Moderator temperature coefficients are compared and differences in kinetic behaviour which generally result in different design philosophies for the two types are mentioned, A comparison of different methods of obtaining flux flattening is presented. The influence of slight enrichment and other coolants, (boiling D{sub 2}O and gases) on the comparison between pressure tube and pressure vessel designs is discussed and illustrated with comparative designs for 400 MW electrical output. This paper was presented at the EAES Enlarged Symposium on Heterogeneous Heavy Water Power Reactors, Mallorca, October 10 - 14, 1960.

Pressure Tube and Pressure Vessel Reactors; certain comparisons

International Nuclear Information System (INIS)

Margen, P.H.; Ahlstroem, P.E.; Pershagen, B.

1961-04-01

In a comparison between pressure tube and pressure vessel type reactors for pressurized D 2 O coolant and natural uranium, one can say that reactors of these two types having the same net electrical output, overall thermal efficiency, reflected core volume and fuel lattice have roughly the same capital cost. In these circumstances, the fuel burn-up obtainable has a significant influence on the relative economics. Comparisons of burn-up values made on this basis are presented in this report and the influence on the results of certain design assumptions are discussed. One of the comparisons included is based on the dimensions and ratings proposed for CANDU. Moderator temperature coefficients are compared and differences in kinetic behaviour which generally result in different design philosophies for the two types are mentioned, A comparison of different methods of obtaining flux flattening is presented. The influence of slight enrichment and other coolants, (boiling D 2 O and gases) on the comparison between pressure tube and pressure vessel designs is discussed and illustrated with comparative designs for 400 MW electrical output. This paper was presented at the EAES Enlarged Symposium on Heterogeneous Heavy Water Power Reactors, Mallorca, October 10 - 14, 1960

[The determination of arterial pressure by the physician or the nurse: its relation to ambulatory pressure and left ventricular mass. The MAPA-Madrid Group. Monitorización Ambulatoria de la Presión Arterial (Ambulatory Monitoring of Arterial Pressure)].

Science.gov (United States)

Martínez, M A; Aguirre, A; Sánchez, M; Nevado, A; Laguna, I; Torre, A; Manuel, E; Villar, C; García-Puig, J

1999-12-11

In the present study we evaluated the influence of the observer's status--physician or nurse--on blood pressure levels and the relationship among clinic blood pressure measurement with ambulatory blood pressure and left ventricle mass. Cross sectional study performed in seven primary care centers. Participating physicians and nurses were trained for blood pressure measurement prior to the study and subsequently retrained at 3 month intervals during the study. Patients included in the study were 122 subjects with mild to moderate hypertension who underwent the following study protocol: a) measurement of clinic blood pressure by physician and nurse, in an independent fashion, on 3 visits; b) clinic-epidemiologic questionnaire; c) conventional hematological and biochemical study; d) electrocardiogram; e) 24-hour ambulatory blood pressure monitoring, f) M-mode and Doppler echocardiography (only in 58 subjects). Nurse-measured blood pressure levels were higher than those determined by physicians (mean differences: 3.9 [6.7] mmHg in systolic blood pressure and 2.6 [5.4] mmHg in diastolic blood pressure). The blood pressure level differences between the two observers were higher in female patients and subjects with low educational level, independently of the observer's gender. Nurse-measured blood pressure was more closely related to ambulatory blood pressure and left ventricle mass than physician-measured blood pressure. Nurse-measured blood pressure levels are lower than those determined by physicians and more closely related to ambulatory blood pressure and left ventricle mass than physician-measured blood pressure. These data support that nurses, instead of doctors, should routinely measure blood pressure in primary care centers.

Moderating ratio parameter evaluation for different materials by means of Monte Carlo calculations and reactivity direct measurements

International Nuclear Information System (INIS)

Borio, A.; Cagnazzo, M.; Marchetti, F.; Pappalardo, P.; Salvini, A.

2004-01-01

The aim of this work is to determine moderating properties of different materials (water, graphite, perfluoropolyethers), in particular the slowing down power (SDP) and the moderating ratio (MR), defined as SDP =ξΣ S and MR=ξΣ S /Σ A , where Σ S and Σ A represent the macroscopic scattering and absorption cross section, respectively, and ξ is the average logarithmic energy loss per collision. Slowing-down power indicates how rapidly a neutron will slow down in the material, but it does not fully explain the effectiveness of the material as a moderator. In fact, a material can slow down neutrons with high efficiency because of its big Σ S , but it can be a poor moderator because with high probability it also absorbs neutrons. Thus, the most complete measure of the effectiveness of a moderator is the moderating ratio parameter which takes into account also the absorption effects: the bigger is the moderating ratio values, the more effectively the material performs as a moderator. The first part of the work consisted in the comparison between the SDP and MR parameter evaluated for different materials by means of Monte Carlo simulations and by means of calculations based on their definition formula (they are developed from knowledge of material composition and of microscopic cross section σ i (derived from literature)). It was found that this comparison showed a good agreement with errors less than 10 %. Thus the Monte Carlo code seems to be a good support for the calculation of the moderating parameters, particularly useful when the materials are compounds of many elements. The second part of the work was dedicated to correlate the materials' MR values with the measured variation of reactivity induced by the insertion of the materials in the core of TRIGA Mark II reactor of the University of Pavia. This is possible by definition of a new parameter for the measure. This parameter, named S, depends on the total weight of the sample inserted in the reactor core

Risky substance use and peer pressure in Swiss young men: Test of moderation effects.

Science.gov (United States)

Studer, Joseph; Baggio, Stéphanie; Grazioli, Véronique S; Mohler-Kuo, Meichun; Daeppen, Jean-Bernard; Gmel, Gerhard

2016-11-01

Peer pressure (PP) toward misconduct is a well-known risk factor for substance use. However, the way it interacts with social factors and the associations of the aspects of PP other than PP toward misconduct have been understudied. This study examined the associations of three aspects of PP with risky substance use and tested whether the associations of PP toward misconduct were moderated by social factors. A representative sample of 5,680 young Swiss males completed a questionnaire assessing risky alcohol, cigarette, and cannabis use, PP toward misconduct, toward peer involvement, and toward peer conformity, as well as social support (SS) and neighbourhood cohesion. Multinomial logistic regression models were used. PP toward misconduct was positively associated with all substance use outcomes. The PP toward misconduct-risky alcohol use association was stronger in individuals reporting high than in those reporting low levels of PP toward peer involvement, SS, and neighbourhood cohesion. The PP toward misconduct-risky cannabis use association was stronger in individuals reporting high than in those reporting low levels of SS and neighbourhood cohesion. The PP toward misconduct-smoking association was stronger in individuals reporting high than in those reporting low levels of PP toward peer involvement. The risk for substance use associated with PP toward misconduct varies as a function of social factors. Being well connected with others (high level of PP toward peer involvement and SS), and living in a cohesive neighbourhood may amplify the risk for risky substance use associated with PP toward misconduct. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Study of the consequences of the rupture of a pressure tube in the tank of a gas-cooled, heavy-water moderated reactor; Etude des consequences de la rupture d'un tube de force dans la cuve d'un reacteur modere a l'eau lourde et refroidi au gaz

Energy Technology Data Exchange (ETDEWEB)

Hareux, F; Roche, R; Vrillon, B [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

Bursting of a pressure tube in the tank of a heavy water moderated-gas cooled reactor is an accident which has been studied experimentally about EL-4. A first test (scale 1) having shown that the burst of a tube does not cause the rupture of adjacent tubes, tests on the tank resistance have been undertaken with a very reduced scale model (1 to 10). It has been found that the tank can endure many bursts of tube without any important deformation. Transient pressure in the tank is an oscillatory weakened wave, the maximum of which (pressure peak) has been the object of a particular experimental study. It appears that the most important parameters which affect the pressure peak are; the pressure of the gas included in the bursting pressure tube, the volume of this gas, the mass of air included in the tank and the nature of the gas. A general method to calculate the pressure peak value in reactor tanks has been elaborated by direct application of experimental data. (authors) [French] L'eclatement d'un tube de force dans la cuve d'un reacteur de puissance modere a l'eau lourde et refroidi par un gaz sous pression est un accident qui a ete etudie experimentalement a propos d'EL-4. Un premier essai a l'echelle 1 ayant montre que l'eclatement d'un tube ne provoque pas celui des tubes voisins, des essais relatifs a la tenue de la cuve ont ete effectues sur maquettes a echelle tres reduite (l/lO). Il a ete trouve que la cuve peut supporter plusieurs eclatements de tubes sans deformations notables. La pression transitoire dans la cuve a une allure oscillatoire amortie dont le maximum (pression de pic) a fait l'objet d'une etude experimentale detaillee. Il apparait que les parametres essentiels influant sur cette pression sont: la pression du gaz contenu dans le tube de force, le volume du gaz qui participe a l'eclatement, la flexibilite de la cuve, la masse d'air empoisonnee dans la cuve, la nature du gaz explosant. Une methode generale d'estimation des pics de pression dans

Fissile fuel assembly for a sub-moderated nuclear reactor

International Nuclear Information System (INIS)

Millot, J.P.; Dejeux, Pol.; Alibran, Patrice.

1983-01-01

Each of the core assemblies is composed of a prismatic case made of a neutron absorbing material, inside which very long rods containing the fissile material are arranged parallel to the height of the case and according to a regular network in the straight sections of the case. At least one piece in a fertile material exposed to the neutrons emitted by the fissile material of the assembly is arranged on each one of the side faces of the case. The invention applies in particular to sub-moderated reactors, cooled and moderated by pressurized water [fr

Economic Evaluations of Strategies to Prevent Hospital-Acquired Pressure Injuries.

Science.gov (United States)

Ocampo, Wrechelle; Cheung, Amanda; Baylis, Barry; Clayden, Nancy; Conly, John M; Ghali, William A; Ho, Chester H; Kaufman, Jaime; Stelfox, Henry T; Hogan, David B

2017-07-01

To provide information from a review of literature about economic evaluations of preventive strategies for pressure injuries (PIs). This continuing education activity is intended for physicians, physician assistants, nurse practitioners, and nurses with an interest in skin and wound care. After participating in this educational activity, the participant should be better able to:1. Identify the purpose and methods used for this study.2. Compare costs and effectiveness related to preventative strategies for PIs. BACKGROUND: Pressure injuries (PIs) are a common and resource-intensive challenge for acute care hospitals worldwide. While a number of preventive strategies have the potential to reduce the cost of hospital-acquired PIs, it is unclear what approach is the most effective. The authors performed a narrative review of the literature on economic evaluations of preventive strategies to survey current findings and identify important factors in economic assessments. Ovid, MEDLINE, NHS Economic Evaluation Databases, and the Cochrane Database of Systematic ReviewsSELECTION CRITERIA: Potentially relevant original research articles and systematic reviews were considered. Selection criteria included articles that were written in English, provided data on cost or economic evaluations of preventive strategies of PIs in acute care, and published between January 2004 and September 2015. Data were abstracted from the articles using a standardized approach to evaluate how the items on the Consolidated Health Economic Evaluation Reporting Standards checklist were addressed. The searches identified 192 references. Thirty-three original articles were chosen for full-text reviews. Nineteen of these articles provided clear descriptions of interventions, study methods, and outcomes considered. Limitations in the available literature prevent firm conclusions from being reached about the relative economic merits of the various approaches to the prevention of PIs. The authors' review

Prediction of moderator temperature under 35% RIH break LOCA with LOECC in CANDU calandria vessel

International Nuclear Information System (INIS)

Yu, Seon Oh; Kim, Man Woong; Kim, Hho Jung; Lee, Jae Yung

2004-01-01

A CANDU reactor has the unique safety features with the intrinsic safety related characteristics that distinguish it from other water-cooled thermal reactors such as a PWR. One of the safety features is that the heavy water moderator is continuously cooled, providing with a heat sink for the decay heat produced in the fuel when there is the LOCA with the coincident failure of the emergency coolant injection (ECI) system. Under such a dual failure condition, the hot pressure tube (PT) would deform into contacting with the calandria tube (CT), providing with an effective heat transfer path from the fuel to the moderator. Following PT/CT contact, there is the spike of the heat flux in the moderator surrounding the CT, which could lead to sustained CT dryout. The prevention of the CT dryout depends on available local moderator subcooling. Higher moderator temperature (or lower subcooling) would decrease the margin of the CTs to dryout. As for LOCAs with coincident loss of the ECI, fuel channel integrity depends on the capability of the moderator as an ultimate heat sink. In this regard, the Canadian Nuclear Safety Commission (CNSC) had categorized the temperature prediction for the moderator cooling integrity as a general action item (GAI) and had recommended that a series of experimental works should be performed to verify the evaluation codes comparing with the results of three-dimensional experimental data. However, although a couple of computer codes were used to predict moderator temperature prediction for those problems, they could not be adequately validated due to the uncertainty of temperature prediction. In this work, the temperature prediction under the transient condition of LOCA with loss of emergency core cooling (LOECC) in a CANDU reactor is conducted using the optimized calculation scheme from the previous work

Evaluating the risk of eye injuries: intraocular pressure during high speed projectile impacts.

Science.gov (United States)

Duma, Stefan M; Bisplinghoff, Jill A; Senge, Danielle M; McNally, Craig; Alphonse, Vanessa D

2012-01-01

To evaluate the risk of eye injuries by determining intraocular pressure during high speed projectile impacts. A pneumatic cannon was used to impact eyes with a variety of projectiles at multiple velocities. Intraocular pressure was measured with a small pressure sensor inserted through the optic nerve. A total of 36 tests were performed on 12 porcine eyes with a range of velocities between 6.2 m/s and 66.5 m/s. Projectiles selected for the test series included a 6.35  mm diameter metal ball, a 9.25  mm diameter aluminum rod, and an 11.16  mm diameter aluminum rod. Experiments were designed with velocities in the range of projectile consumer products such as toy guns. A range of intraocular pressures ranged between 2017 mmHg to 26,426 mmHg (39 psi-511 psi). Four of the 36 impacts resulted in globe rupture. Intraocular pressures dramatically above normal physiological pressure were observed for high speed projectile impacts. These pressure data provide critical insight to chronic ocular injuries and long-term complications such as glaucoma and cataracts.

ARTERIAL STIFFNESS PARAMETERS IN PATIENTS WITH MODERATE/HIGH CARDIOVASCULAR RISK DURING LISINOPRIL AND SIMVASTATIN TREATMENT

Directory of Open Access Journals (Sweden)

V. N. Isakova

2016-01-01

Full Text Available Aim. To evaluate parameters of arterial stiffness by non-invasive arteriography in patients with moderate/high cardiovascular risk receiving lisinopril and simvastatin.Material and methods. 20 patients (aged 50-55 y.o. with arterial hypertension of the 1st degree and dislipidemia are included in the study. All patients had pulse wave velocity (PWV ≥ 10 m/s and/or the corrected index of pulse wave augmentation (AI × 80 ≥ -10% according to non-invasive arteriography data; and moderate-high cardiovascular risk (≥ 3%. Patients received therapy with lisinopril and simvastatin. Blood pressure (BP levels and lipid profiles were assessed before therapy and in 1, 2, 6 and 12 month of the observation. Non-invasive arteriography was performed before therapy and in 2, 6 and 12 months later.Results. BP target levels were reached within 1 month of treatment as well as improvement of lipid profile was reached within 2 months in majority of the patients. Reference PWV and AI were reached in 85,7% of patients within one year of treatment.Conclusion. Arterial stiffness parameters help to evaluate cardiovascular risk changes accurately as the results of treatment.

Development of Evaluation Technology of the Integrity of HWR Pressure Tubes

Energy Technology Data Exchange (ETDEWEB)

Jeong, Y. M.; Kim, Y. S.; Im, K. S.; Kim, K. S.; Ahn, S. B

2007-06-15

Zr-2.5Nb pressure tubes are one of the most critical structural components governing the lifetime of the heavy water reactors to carry fuel bundles and heavy coolant water inside. Since they are being degraded during their operation in reactors due to dimensional changes caused by creep and irradiation growth, neutron irradiation and delayed hydride cracking, it is required to evaluate their degradation by conducting material testing and examinations on the highly irradiated pressure tubes in hot cells and to keep tracking of their degradation behavior with operation time, which are the aim of this project.

Pressurized thermal shock evaluation of the Calvert Cliffs Unit 1 Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Abbott, L [ed.

1985-09-01

An evaluation of the risk to the Calvert Cliffs Unit 1 nuclear power plant due to pressurized thermal shock (PTS) has been completed by Oak Ridge National Laboratory (ORNL) with the assistance of several other organizations. This evaluation was part of a Nuclear Regulatory Commission program designed to study the PTS risk to three nuclear plants, the other two plants being Oconee Unit 1 and H.B. Robinson Unit 2. The specific objectives of the program were to (1) provide a best estimate of the frequency of a through-the-wall crack in the pressure vessel at each of the three plants, together with the uncertainty in the estimated frequency and its sensitivity to the variables used in the evaluation; (2) determine the dominant overcooling sequences contributing to the estimated frequency and the associated failures in the plant systems or in operator actions; and (3) evaluate the effectiveness of potential corrective measures.

Pressurized thermal shock evaluation of the Calvert Cliffs Unit 1 Nuclear Power Plant

International Nuclear Information System (INIS)

Abbott, L.

1985-09-01

An evaluation of the risk to the Calvert Cliffs Unit 1 nuclear power plant due to pressurized thermal shock (PTS) has been completed by Oak Ridge National Laboratory (ORNL) with the assistance of several other organizations. This evaluation was part of a Nuclear Regulatory Commission program designed to study the PTS risk to three nuclear plants, the other two plants being Oconee Unit 1 and H.B. Robinson Unit 2. The specific objectives of the program were to (1) provide a best estimate of the frequency of a through-the-wall crack in the pressure vessel at each of the three plants, together with the uncertainty in the estimated frequency and its sensitivity to the variables used in the evaluation; (2) determine the dominant overcooling sequences contributing to the estimated frequency and the associated failures in the plant systems or in operator actions; and (3) evaluate the effectiveness of potential corrective measures

Personality as a moderator of context effects on academic achievement

NARCIS (Netherlands)

Hendriks, A.A.J.; Kuyper, H.; Lubbers, M.J; Van der Werf, M.P.C.

We investigated whether personality moderates group influence of classmates on academic achievement and whether these so-called context effects can be attributed to peer pressure. The sample consisted of 2498 students in their first year of Dutch secondary education. The data were analyzed by a

Evaluation of Flexible Force Sensors for Pressure Monitoring in Treatment of Chronic Venous Disorders.

Science.gov (United States)

Parmar, Suresh; Khodasevych, Iryna; Troynikov, Olga

2017-08-21

The recent use of graduated compression therapy for treatment of chronic venous disorders such as leg ulcers and oedema has led to considerable research interest in flexible and low-cost force sensors. Properly applied low pressure during compression therapy can substantially improve the treatment of chronic venous disorders. However, achievement of the recommended low pressure levels and its accurate determination in real-life conditions is still a challenge. Several thin and flexible force sensors, which can also function as pressure sensors, are commercially available, but their real-life sensing performance has not been evaluated. Moreover, no researchers have reported information on sensor performance during static and dynamic loading within the realistic test conditions required for compression therapy. This research investigated the sensing performance of five low-cost commercial pressure sensors on a human-leg-like test apparatus and presents quantitative results on the accuracy and drift behaviour of these sensors in both static and dynamic conditions required for compression therapy. Extensive experimental work on this new human-leg-like test setup demonstrated its utility for evaluating the sensors. Results showed variation in static and dynamic sensing performance, including accuracy and drift characteristics. Only one commercially available pressure sensor was found to reliably deliver accuracy of 95% and above for all three test pressure points of 30, 50 and 70 mmHg.

Thermo-hydraulic test of the moderator cell of liquid hydrogen cold neutron source for the Budapest research reactor

International Nuclear Information System (INIS)

Grosz, Tamas; Rosta, Laszlo; Hargitai, Tibor; Mityukhlyaev, V.A.; Serebrov, A.P.; Zaharov, A.A.

1999-01-01

Thermo-hydraulic experiment was carried out in order to test performance of the direct cooled liquid hydrogen moderator cell to be installed at the research reactor of the Budapest Neutron Center. Two electric hearers up to 300 W each imitated the nuclear heat release in the liquid hydrogen as well as in construction material. The test moderator cell was also equipped with temperature gauges to measure the hydrogen temperature at different positions as well as the inlet and outlet temperature of cooling he gas. The hydrogen pressure in the connected buffer volume was also controlled. At 140 w expected total heat load the moderator cell was filled with liquid hydrogen within 4 hours. The heat load and hydrogen pressure characteristics of the moderator cell are also presented. (author)

Effect of plasma colloid osmotic pressure on intraocular pressure during haemodialysis

OpenAIRE

Tokuyama, T.; Ikeda, T.; Sato, K.

1998-01-01

BACKGROUND—In a previous case report, it was shown that an increase in plasma colloid osmotic pressure induced by the removal of fluid during haemodialysis was instrumental in decreasing intraocular pressure. The relation between changes in intraocular pressure, plasma osmolarity, plasma colloid osmotic pressure, and body weight before and after haemodialysis is evaluated.
METHODS—Intraocular pressure, plasma osmolarity, plasma colloid osmotic pressure, and body weight were evaluated before a...

Radiological experience on decontamination of moderator and associated system at NAPS-1

International Nuclear Information System (INIS)

Yadav, C.L.R.; Mitra, S.R.; Pawar, S.K.; Lal Chand

2000-01-01

Narora Atomic Power Station, the first of Indian standardized Pressurized Heavy Water Reactor, is faced with a problem of 60 Co contamination in moderator and its associated system. This contamination has resulted in increase of collective dose contribution. As a part of ALARA campaign in NAPS it was decided to decontaminate the moderator and associated systems and also incorporate modification which will further control the 60 Co contamination. As a part of decontamination program several experiments to determine the effectiveness of the chemical formulation on SS and cupro-nickel surfaces were carried out on various moderator system equipment before finalizing the formulation for full scale decontamination of moderator system. This paper gives an overview of various modifications in system and decontamination efficiency of various chemical formulation which were used for decontamination of moderator system (excluding calandria) and associated equipment. (author)

Prevalence of pre-high blood pressure and high blood pressure among non-overweight children and adolescents using international blood pressure references in developed regions in China.

Science.gov (United States)

Tian, Changwei; Xu, Shuang; Wang, Hua; Wang, Wenming; Shen, Hui

2017-09-01

There is a lack of data on the prevalence of pre-high blood pressure (PreHBP) and high blood pressure (HBP), based on recent international blood pressure references, in non-overweight children and adolescents. To describe the prevalence of PreHBP and HBP in non-overweight children and adolescents in developed regions of China. In total, 588 097 non-overweight children and adolescents aged 6-17 years from the National Surveys on Chinese Students' Constitution and Health in 2015 were included. The prevalence of PreHBP was 13.41% and subjects in urban areas had a higher prevalence of PreHBP (14.14%) than those in rural areas (12.92%). Subjects in regions with a high (13.56%) or moderate (13.61%) socioeconomic status showed a higher prevalence of PreHBP than those in regions with a relatively low socioeconomic status (12.76%). A similar pattern was found for the prevalence of HBP, and the prevalence of HBP was 18.25% for all participants, 20.55% for subjects in urban areas, 16.71% in rural areas, 18.76% in high socioeconomic areas, 18.62% in moderate socioeconomic areas and 16.70% in relatively low socioeconomic areas. A large proportion of non-overweight children and adolescents had elevated blood pressure and there were urban-rural and socioeconomic disparities in the prevalence of elevated blood pressure.

Solving the Fluid Pressure Poisson Equation Using Multigrid-Evaluation and Improvements.

Science.gov (United States)

Dick, Christian; Rogowsky, Marcus; Westermann, Rudiger

2016-11-01

In many numerical simulations of fluids governed by the incompressible Navier-Stokes equations, the pressure Poisson equation needs to be solved to enforce mass conservation. Multigrid solvers show excellent convergence in simple scenarios, yet they can converge slowly in domains where physically separated regions are combined at coarser scales. Moreover, existing multigrid solvers are tailored to specific discretizations of the pressure Poisson equation, and they cannot easily be adapted to other discretizations. In this paper we analyze the convergence properties of existing multigrid solvers for the pressure Poisson equation in different simulation domains, and we show how to further improve the multigrid convergence rate by using a graph-based extension to determine the coarse grid hierarchy. The proposed multigrid solver is generic in that it can be applied to different kinds of discretizations of the pressure Poisson equation, by using solely the specification of the simulation domain and pre-assembled computational stencils. We analyze the proposed solver in combination with finite difference and finite volume discretizations of the pressure Poisson equation. Our evaluations show that, despite the common assumption, multigrid schemes can exploit their potential even in the most complicated simulation scenarios, yet this behavior is obtained at the price of higher memory consumption.

Quantitative evaluation of the effect of buffer pressure on well output

Energy Technology Data Exchange (ETDEWEB)

Kobrushko, A T

1980-01-01

In the examples of the Pashninskiy and the Usinskiy fields of the Komi ASSR, a method is presented for determining the possible increase in output of a gusher well on decrease in the buffer pressure. A quantitative evaluation of this increase is presented. The essence of the method is construction of a nomogram for characteristics of a gusher lifter and indicator diagrams of the wells combined in one figure. Mutual intersection of the characteristics and diagrams corresponds to the steady-state operating mode of the bed-well system. Cases are examined of productivity 10, 25, 50 and 100 m/sup 3//day of the MPa for the Pashninskiy and 25, 50, 102 and 200 m/sup 3//day of the MPa for the Usinskiy fields. Despite the broad range of well productivity, and also the significant difference in fields according to gushing conditions, increase of the well output for 0.1 MPa of decrease in buffer pressure differs little. In the interval of buffer pressures 2.00.5 MPa, the specific increase of output from decrease in buffer pressure is very significant and is 7-10 m/sup 3//day. The findings convincingly proved the expediency of using systems of oil and gas recovery at new fields with possibly low pressure in the pipelines.

Two-phase pressure drop and heat transfer of sodium at forced convection

International Nuclear Information System (INIS)

Grieb, G.

1989-04-01

Experiments with sodium for the two-phase pressure drop in vertical tubes with upward flow (internal diameters 6 and 9 mm) performed at the Joint Research Centre (JRC) of the European Communities in Ispra, Italy, and at the Nuclear Research Centre in Karlsruhe (KfK) were evaluated and analysed. Furthermore, experiments for the single-phase and two-phase heat transfer in the grid spaced twelve-rod bundle (p d /d =1.3, rod diameter 8 mm) with flow in axial direction performed at the JRC were evaluated and analysed. The pressure drop measurements were carried out at moderate to high mass flow rates (30 to 4500 kg/(m 2 s)) and at moderate pressures (50 to 300 kPa, density ratio ρ f /ρ g = 950 to 5400). The measurements for the single-phase heat transfer at high heat fluxes (0.16 to 1.6 MW/m 2 ) were carried out in the Reynolds number region (3100 2 s)) and at high heat fluxes (0.46 to 1.6 MW/m 2 ) within the temperature range from 870 to 970 0 C. For the subsequent calculation of the experiments relating to the two-phase pressure drop a computer program was developed, which is based on the so-called slip model. It requires a friction pressure loss correlation and a slip correlation. The tested correlations were not suitable for describing the experimental measurements. Accordingly, simplified equations of momentum were used to develop a new slip correlation for the case of annular flow together with the annular-mist flow, the most important two-phase flow regimes for sodium in the measurement range. After the inception of the entrainment - transition from the annular flow to the annular-mist flow - an even larger fraction of liquid enters the vapour core in the form of droplets, as the vapour quality increases. An equation was formulated for the slip in this region and adapted to the experiments via coefficients. (orig./GL) [de

MicroRNAs are associated with blood-pressure effects of exposure to particulate matter: Results from a mediated moderation analysis.

Science.gov (United States)

Motta, Valeria; Favero, Chiara; Dioni, Laura; Iodice, Simona; Battaglia, Cristina; Angelici, Laura; Vigna, Luisella; Pesatori, Angela Cecilia; Bollati, Valentina

2016-04-01

Exposure to particulate air pollution is associated with increased blood pressure (BP), a well-established risk factor for cardiovascular disease. To elucidate the mechanisms underlying this relationship, we investigated whether the effects of particulate matter of less than 10μm in aerodynamic diameter (PM10) on BP are mediated by microRNAs. We recruited 90 obese individuals and we assessed their PM10 exposure 24 and 48h before the recruitment day. We performed multivariate linear regression models to investigate the effects of PM10 on BP. Using the TaqMan® Low-Density Array, we experimentally evaluated and technically validated the expression levels of 377 human miRNAs in peripheral blood. We developed a mediated moderation analysis to estimate the proportion of PM10 effects on BP that was mediated by miRNA expression. PM10 exposure 24 and 48h before the recruitment day was associated with increased systolic BP (β=1.22mmHg, P=0.019; β=1.24mmHg, P=0.019, respectively) and diastolic BP (β=0.67mmHg, P=0.044; β=0.91mmHg, P=0.007, respectively). We identified nine miRNAs associated with PM10 levels 48h after exposure. A conditional indirect effect (CIE=-0.1431) of PM10 on diastolic BP, which was mediated by microRNA-101, was found in individuals with lower values of mean body mass index. Our data provide evidence that miRNAs are a molecular mechanism underlying the BP-related effects of air pollution exposure, and indicate miR-101 as epigenetic mechanism to be further investigated. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Is the area under blood pressure curve the best parameter to evaluate 24-h ambulatory blood pressure monitoring data?

Science.gov (United States)

Nobre, Fernando; Mion, Décio

2005-10-01

Ambulatory blood pressure monitoring (ABPM) provides relevant data about blood pressure over a 24-h period. The analysis of parameters to determine the blood pressure profile from these data is of great importance. To calculate areas under systolic and diastolic blood pressure curves (SBP-AUC/DBP-AUC) and compare with systolic and diastolic blood pressure load (SBPL/DBPL) and 24-h systolic and diastolic blood pressure (24-h SBP/24-h DBP) in order to determine which provides the best correlation with left ventricular mass index (LVMI). ABPM measurements (1143 individuals) were analyzed to obtain 24-h SBP/24-h DBP, SBPL/DBPL, and SBP-AUC/ DBP-AUC, using Spacelabs (90207) and CardioSistemas devices. Left ventricular mass was determined using an echocardiograph HP Sonos 5500 and LVMI was calculated. The correlations between all possible pairs within the group 24-h SBP/SBPL/SBP-AUC and 24-h DBP/DBPL/DBP-AUC were high and statistically significant. The correlations between 24-h SBP/24-h DBP and SBP-AUC/DBP-AUC with SBPL/DBPL close to 100%, were lower than those mentioned above. The correlations of the parameters obtained by ABPM with LVMI were also high and statistically significant, except for blood pressure load between 90 and 100%, and for 24-h SBP of 135 mmHg or less and SBPL higher than 50%. SBPL/DBPL and SBP-AUC/DBP-AUC can be used for the evaluation of ABPM data owing to the strong correlation with 24-h SBP/24-h DBP and with LVMI, except when SBPL is close to 100% or 24-h SBP is below 135 mmHg but SBPL is above 50%. SBP-AUC/DBP-AUC, however, are a better alternative because they do not have the limitations of blood pressure load or even of 24-h blood pressure present.

Effect of Flow Configuration on Velocity and Temperature Distribution of Moderator Inside 540 MWe PHWR Calandria using CFD Techniques

International Nuclear Information System (INIS)

Bharj, J.S.; Sahaya, R.R.; Datta, D.; Dharne, S.P.

2006-01-01

The calandria of a Pressurized Heavy Water Reactor (PHWR) is a horizontal cylindrical vessel housing a matrix of horizontal tubes called calandria tubes, through which pass the pressure tubes that house the fuel bundles. The calandria is filled with heavy water acting as moderator. A large amount of heat (about 95 MW) is generated within the moderator mainly due to neutron slowing down and attenuation of gamma radiations. In the present configuration of 540 MWe calandria, moderator inlet diffusers are directed upwards and the outlet is from the bottom of the calandria. This configuration is not conducive for the buoyancy-dominated flows generated due to large volumetric heat generation in the moderator. In order to decide the effects of changes in flow configuration by changing location/direction of inlet/outlet nozzles, a study was done for moderator flows in the using PHOENICS CFD software. The results of study with various flow configurations show that modification in moderator flow configuration, reduces the peak temperature of moderator in calandria by about 12 deg C as well as gives a much more uniform temperature distribution. (authors)

ABPM comparison of the anti-hypertensive profiles of telmisartan and enalapril in patients with mild-to-moderate essential hypertension.

Science.gov (United States)

Amerena, J; Pappas, S; Ouellet, J P; Williams, L; O'Shaughnessy, D

2002-01-01

In this multicentre, prospective, randomized, open-label, blinded-endpoint (PROBE) study, the efficacy of 12 weeks' treatment with once-daily telmisartan 40-80 mg and enalapril 10-20 mg was evaluated using ambulatory blood pressure monitoring (ABPM) in 522 patients with mild-to-moderate essential hypertension. Patients were titrated to the higher dose of study drug at week 6 if mean seated diastolic blood pressure (DBP) was > or = 90 mmHg. The primary endpoint was the change from baseline in ambulatory DBP in the last 6 h of the 24-h dosing interval after 12 weeks' treatment. Telmisartan and enalapril produced similar reductions from baseline in DBP and systolic blood pressure (SBP) over all ABPM periods evaluated (last 6 h, 24-h, daytime and night-time). Telmisartan produced a significantly greater reduction in mean seated trough DBP, measured unblinded with an automated ABPM device in the clinic, amounting to a difference of -2.02 mmHg (P ABPM device. Both treatments were well tolerated. Compared with telmisartan, enalapril was associated with a higher incidence of cough (8.9% versus 0.8%) and hypotension (3.9% versus 1.1%). Therefore, telmisartan may provide better long-term compliance and, consequently, better blood pressure control than enalapril.

[Evaluation of accuracy of measuring intraocular pressure by handheld non-contact applanation tonometer].

Science.gov (United States)

Chen, X; Peng, D; Zhou, W; Zhong, Y

1995-06-01

To evaluate the accuracy of measuring intraocular pressure by handheld non-contact applanation tonometer. 58 patients' (113 eyes) intraocular pressure were measured by Keeler, non-contact tonometer and R 900 Goldmann applanation tonometer and the results of measurement of intraocular pressure by the two kinds of tonometers were compared. The mean intraocular pressure measured by non-contact is 16.31 +/- 5.59 mmHg and 17.49 +/- 6.13 mmHg (1 mmHg = 0.1333 kPa) by Goldmann applanation tonometer, respectively. There was no statistical significance to be found (P > 0.05) between the two methods. By linear correlation and regression analysis, a positive correlation was found between the two methods (r = 0.8942, b = 0.8154). The handheld non-contact tonometer has the same accuracy and reliability of measurement of intraocular pressure comparing with Goldmann applanation tonometer, and it can be used in glaucoma clinic and screening.

Moderate alcohol use and cardiovascular disease from Mendelian randomization.

Directory of Open Access Journals (Sweden)

Shiu Lun Au Yeung

Full Text Available BACKGROUND: Observational studies show moderate alcohol use negatively associated with ischemic heart disease (IHD and cardiovascular disease (CVD. However, healthier attributes among moderate users compared to never users may confound the apparent association. A potentially less biased way to examine the association is Mendelian randomization, using alcohol metabolizing genes which influence alcohol use. METHODS: We used instrumental variable analysis with aldehyde dehydrogenase 2 (ALDH2 genotypes (AA/GA/GG as instrumental variables for alcohol use to examine the association of alcohol use (10 g ethanol/day with CVD risk factors (blood pressure, lipids and glucose and morbidity (self-reported IHD and CVD among men in the Guangzhou Biobank Cohort Study. RESULTS: ALDH2 genotypes were a credible instrument for alcohol use (F-statistic 74.6. Alcohol was positively associated with HDL-cholesterol (0.05 mmol/L per alcohol unit, 95% confidence interval (CI 0.02 to 0.08 and diastolic blood pressure (1.15 mmHg, 95% CI 0.23 to 2.07 but not with systolic blood pressure (1.00 mmHg, 95% CI -0.74 to 2.74, LDL-cholesterol (0.03 mmol/L, 95% CI -0.03 to 0.08, log transformed triglycerides (0.03 mmol/L, 95% CI -0.01 to 0.08 or log transformed fasting glucose (0.01 mmol/L, 95% CI -0.006 to 0.03, self-reported CVD (odds ratio (OR 0.98, 95% CI 0.76 to 1.27 or self-reported IHD (OR 1.10, 95% CI 0.83 to 1.45. CONCLUSION: Low to moderate alcohol use among men had the expected effects on most CVD risk factors but not fasting glucose. Larger studies are needed to confirm the null associations with IHD, CVD and fasting glucose.

Reactor-moderated intermediate-energy neutron beams for neutron-capture therapy

International Nuclear Information System (INIS)

Less, T.J.

1987-01-01

One approach to producing an intermediate energy beam is moderating fission neutrons escaping from a reactor core. The objective of this research is to evaluate materials that might produce an intermediate beam for NCT via moderation of fission neutrons. A second objective is to use the more promising moderator material in a preliminary design of an NCT facility at a research reactor. The evaluations showed that several materials or combinations of materials could produce a moderator source for an intermediate beam for NCT. The best neutron spectrum for use in NCT is produced by Al 2 O 3 , but mixtures of Al metal and D 2 O are also attractive. Using the best moderator materials, results were applied to the design of an NCT moderator at the Georgia Institute of Technology Research Reactor's bio-medical facility. The amount of photon shielding and thermal neutron absorber were optimized with respect to the desired photon dose rate and intermediate neutron flux at the patient position

Evaluation of pressure tuning of enzymes

DEFF Research Database (Denmark)

Naghshineh, Mahsa

and high energy consumption. Therefore, searching for an environmentally friendly method of pectin extraction is a task for science and industry. Employment of hydrolytic enzymes may represent a green approach to obtain intact pectin polymer. However, the low stability/activity of enzymes, and low polymer...... yield of enzymatic extraction limits the application of enzyme in pectin production. There is evidence that emerging technology of high hydrostatic pressure processing can result in stabilization and activation of some enzymes. Therefore, the use of high hydrostatic pressure in combination with enzyme...... (cellulase/xylanase: 50/0, 50/25, 50/50, 25/50, and 0/50 U/g lime peel) at ambient pressure, 100 and 200 MPa were used to extract pectin from dried lime peel waste. It was found that pressure level, type and concentration of enzyme significantly influenced pectin yield and degree of esterification (DE...

High pressure inactivation of relevant target microorganisms in poultry meat products and the evaluation of pressure-induced protein denaturation of marinated poultry under different high pressure treatments

Science.gov (United States)

Schmidgall, Johanna; Hertel, Christian; Bindrich, Ute; Heinz, Volker; Toepfl, Stefan

2011-03-01

In this study, the possibility of extending shelf life of marinated poultry meat products by high pressure processing was evaluated. Relevant spoilage and pathogenic strains were selected and used as target microorganisms (MOs) for challenge experiments. Meat and brine were inoculated with MOs and treated at 450 MPa, 4 °C for 3 min. The results of inactivation show a decreasing pressure tolerance in the series Lactobacillus > Arcobacter > Carnobacterium > Bacillus cereus > Brochothrix thermosphacta > Listeria monocytogenes. Leuconostoc gelidum exhibited the highest pressure tolerance in meat. A protective effect of poultry meat was found for L. sakei and L. gelidum. In parallel, the influence of different marinade formulations (pH, carbonates, citrates) on protein structure changes during a pressure treatment was investigated. Addition of sodium carbonate shows a protection against denaturation of myofibrillar proteins and provides a maximum water-holding capacity. Caustic marinades allowed a higher retention of product characteristics than low-pH marinades.

Neutron moderators for the European Spallation Source

DEFF Research Database (Denmark)

Klinkby, Esben Bryndt; Zanini, L.; Batkov, K.

The design of the neutron moderators for the European Spallation Source, intended to be installed at the start of operations of the facility in 2019 has now been finalized and the moderators are being fabricated. Among the driving principles in the design have been flexibility for instruments...... to have access to cold and thermal neutrons with highest possible source brightness. Different design and configuration options were evaluated. The final configuration accepted for construction foresees two moderators with identical para-hydrogen (so-called "butterfly") shape, but different heights......, placed above and below the spallation target. Both moderators are able to serve the full 2 x 120° beam extraction sectors of instrument suite. The top, 3-cm tall moderator, has both high thermal and high cold brightness, more than by a factor of 2.5 compared to the previous design of the Technical Design...

Probabilistic evaluation of concrete containment capacity for beyond design basis internal pressures

International Nuclear Information System (INIS)

Tang, H.T.; Dameron, R.A.; Rashid, Y.R.

1995-01-01

For beyond design basis internal pressure loading, experimental studies have demonstrated that the most probable failure mode governing the ultimate functional capacity of concrete containments is leak rather than break. Based on leak rates measured in experiments, a prediction formula for leak rate as functions of containment liner size and internal pressure has been postulated. The determination of liner tear is cast in a probabilistic framework. In calculating leakage, particular attention is paid to the evaluation of leakage versus rupture and the loading rates that may be required to leapfrog over a leakage mode. (orig.)

The construction and evaluation of a high pressure manifold and vessels for a Calvet type microcalorimeter

International Nuclear Information System (INIS)

Jones, D.E.G.; Turcotte, A.-M.; Fouchard, R.C.

2003-01-01

A Setaram C-80 calorimeter has been modified in order to measure the heat flow of energetic materials at pressures up to 69 MPa. A manifold and sample cells capable of operating at high pressure were designed, constructed and evaluated. This paper will describe, in detail, the high pressure manifold construction, safety assessment and calibration. As well, the results for initial trials with ammonium nitrate (AN), and pentaerythritol tetranitrate (PETN) at various pressures and heating rates will be discussed

A method for evaluating pressure locking and thermal binding of gate valves

Energy Technology Data Exchange (ETDEWEB)

Dogan, T.

1996-12-01

A method is described to evaluate the susceptibility of gate valves to pressure locking and thermal binding. Binding of the valve disc in the closed position due to high pressure water trapped in the bonnet cavity (pressure locking) or differential thermal expansion of the disk in the seat (thermal binding) represents a potential mechanism that can prevent safety-related systems from functioning when called upon. The method described here provides a general equation that can be applied to a given gate valve design and set of operating conditions to determine the susceptibility of the valve to fail due to disc binding. The paper is organized into three parts. The first part discusses the physical mechanisms that cause disc binding. The second part describes the mathematical equations. The third part discusses the conclusions.

Physiological and emotional responses to subjective social evaluative threat in daily life.

Science.gov (United States)

Lehman, Barbara J; Cane, Arianna C; Tallon, Shannon J; Smith, Stephanie F

2015-01-01

This study examined concurrent and delayed emotional and cardiovascular correlates of naturally occurring experiences with subjective social evaluative threat (SSET) and tested whether individual differences in social interaction anxiety moderated those associations. Sixty-eight participants wore ambulatory blood pressure monitors for three days. Following each blood pressure reading, participants reported on SSET and negative emotions, yielding 1770 momentary measures. Multilevel modeling suggested that reports of greater SSET uniquely predicted elevations in anxiety and embarrassment, with elevations in anxiety, embarrassment, and shame extending to the hour following SSET. Reports of concurrent and previous-hour SSET also predicted cardiovascular elevations. Linkages between SSET and anxiety and shame, but not cardiovascular measures, were moderated by social interaction anxiety. Those higher in social interaction anxiety showed especially strong associations between SSET and both concurrent and delayed anxiety and greater delayed shame. This research suggests an important role for anxiety, embarrassment, and shame as emotional consequences of naturally occurring evaluative threat, especially for those who are more socially anxious. Further, this work replicates other naturalistic studies that have documented increased blood pressure at times of SSET and extends that work by documenting cardiovascular responses into the following hour.

Design concept of the HPLWR moderator flow path

International Nuclear Information System (INIS)

Koehly, Christina; Schulenberg, Thomas; Starflinger, Joerg

2009-01-01

The latest design concept of the High Performance Light Water Reactor (HPLWR) includes a thermal core in which supercritical water at 25 MPa inlet pressure is heated up from 280degC reactor inlet temperature to 500degC core exit temperature in three steps with intermediate coolant mixing to minimize peak cladding temperatures of the fuel rods. Prior to entering the first fuel assemblies, the coolant is used as moderator in water rods inside assemblies, in the gap volume between assembly boxes, as well as in the surrounding axial or radial reflectors. Even though assembly boxes and moderator rods are designed with a certain thermal insulation, heat is generated in the moderator water or transferred to it from the superheated steam inside assemblies, causing concern of natural convection phenomena with uncontrolled neutronic feedback on the core power distribution. Moreover, bypass flows of the moderator water need to be minimized at any thermal expansion of the reactor internal structures to avoid an unpredictable moderator mass flow. The design concept of the moderator flow path described in this paper is trying to overcome these problems. Downward flow of moderator water is limited to sub-cooled conditions, well below the pseudo-critical point of supercritical water. Dedicated orifices are foreseen to allow later correction of the mass flow split. The sealing concept accounts for larger thermal expansions of reactor components by using C-rings or bellows. A welded construction is preferred wherever possible to minimize leakage. The removable steam plenum is aligned at the extractable steam pipes to minimize thermal displacements at the sealing positions. The paper is showing several design details to illustrate the technical solutions. (author)

Evaluation of Pressure Generated by Resistors From Different Positive Expiratory Pressure Devices.

Science.gov (United States)

Fagevik Olsén, Monika; Carlsson, Maria; Olsén, Erik; Westerdahl, Elisabeth

2015-10-01

Breathing exercises with positive expiratory pressure (PEP) are used to improve pulmonary function and airway clearance. Different PEP devices are available, but there have been no studies that describe the pressure generated by different resistors. The purpose of this study was to compare pressures generated from the proprietary resistor components of 4 commercial flow-dependent PEP valves with all other parameters kept constant. Resistors from 4 flow-regulated PEP devices (Pep/Rmt system, Wellspect HealthCare; Pipe P breathing exerciser, Koo Medical Equipment; Mini-PEP, Philips Respironics [including resistors by Rüsch]; and 15-mm endo-adapter, VBM Medizintechnik) were tested randomly by a blinded tester at constant flows of 10 and 18 L/min from an external gas system. All resistors were tested 3 times. Resistors with a similar diameter produced statistically significant different pressures at the same flow. The differences were smaller when the flow was 10 L/min compared with 18 L/min. The differences were also smaller when the diameter of the resistor was increased. The pressures produced by the 4 resistors of the same size were all significantly different when measuring 1.5- and 2.0-mm resistors at a flow of 10 L/min and 2.0-mm resistors at a flow of 18 L/min (P < .001). There were no significant differences between any of the resistors when testing sizes of 4.5 and 5.0 mm at either flow. The Mini-PEP and adapter resistors gave the highest pressures. Pressures generated by the different proprietary resistor components of 4 commercial PEP devices were not comparable, even though the diameter of the resistors is reported to be the same. The pressures generated were significantly different, particularly when using small-diameter resistors at a high flow. Therefore, the resistors may not be interchangeable. This is important information for clinicians, particularly when considering PEP for patients who do not tolerate higher pressures. Copyright © 2015 by

Evaluation Of Liner Back-pressure Due To Concrete Pore Pressure At Elevated Temperatures

International Nuclear Information System (INIS)

James, R.J.; Rashid, Y.R.; Liu, A.S.; Gou, B.

2006-01-01

GE's latest evolution of the boiling water reactor, the ESBWR, has innovative passive design features that reduce the number and complexity of active systems, which in turn provide economic advantages while also increasing safety. These passive systems used for emergency cooling also mean that the primary containment system will experience elevated temperatures with longer durations than conventional plants in the event of design basis accidents. During a Loss of Coolant Accident (LOCA), the drywell in the primary containment structure for the ESBWR will be exposed to saturated steam conditions for up to 72 hours following the accident. A containment spray system may be activated that sprays the drywell area with water to condense the steam as part of the recovery operations. The liner back-pressure will build up gradually over the 72 hours as the concrete temperatures increase, and a sudden cool down could cause excessive differential pressure on the liner to develop. For this analysis, it is assumed that the containment spray is activated at the end of the 72-hour period. A back-pressure, acting between the liner and the concrete wall of the containment, can occur as a result of elevated temperatures in the concrete causing steam and saturated vapor pressures to develop from the free water remaining in the pores of the concrete. Additional pore pressure also develops under the elevated temperatures from the non-condensable gases trapped in the concrete pores during the concrete curing process. Any buildup of this pore pressure next to the liner, in excess of the drywell internal pressure, will act to push the liner away from the concrete with a potential for tearing at the liner anchorages. This paper describes the methods and analyses used to quantify this liner back-pressure so that appropriate measures are included in the design of the liner and anchorage system. A pore pressure model is developed that calculates the pressure distribution across the concrete

CLINICAL STUDY TO EVALUATE THE VISUAL OUTCOME AND PATIENT COMFORT IN LASIK AND PHOTOREFRACTIVE KERATECTOMY IN LOW-TO-MODERATE MYOPIC ASTIGMATISM PATIENTS

OpenAIRE

Ashok Kumar P; Ananda Babu M; Radha Priyadharshini R; Jeevitha A

2017-01-01

BACKGROUND To evaluate visual outcomes following LASIK and Photorefractive Keratectomy (PRK) in low-to-moderate myopia and/or myopic astigmatism in age and refractive error matched eyes. MATERIALS AND METHODS Of a total 30 patients aged ≥21 years, 20 (40 eyes) underwent LASIK and 10 (20 eyes) underwent PRK for low-to-moderate myopia or myopic astigmatism. LASIK was performed with the Alcon wave light 500 and PRK with the alcohol application for epithelial removal. All abl...

On the neutron slowing-down in moderators

Energy Technology Data Exchange (ETDEWEB)

Caldeira, Alexandre D., E-mail: alexdc@ieav.cta.br [Instituto de Estudos Avançados (IEAV), São José dos Campos, SP (Brazil). Divisão de Energia Nuclear

2017-07-01

Neutron slowing-down is a very important subject to be considered in several areas of nuclear energy application, such as thermal nuclear reactors, nuclear medicine, radiological protection, detectors design and so on. Moderator materials are the responsible to perform this task and among the neutron induced cross sections, the elastic scattering cross section is the main nuclear interaction in this case. At thermal neutron energies, the moderator molecular or crystalline structure become important and dependent on the moderator phase, gas, liquid, or solid, its cross sections and, consequently, the angular and energy distributions of the scattered neutron are affected. The procedures used for generating correctly moderators cross sections at thermal neutron energies from evaluated nuclear data files utilizing the NJOY system are addressed. (author)

Description of code system PLES/PTS for evaluation of pressure vessel integrity during PTS events

International Nuclear Information System (INIS)

Hirano, Masashi; Kohsaka, Atsuo.

1992-02-01

A code system PLES/PTS has been developed at the Japan Atomic Energy Research Institute (JAERI) to evaluate the integrity of the pressure vessel during plant thermal-hydraulic transients related to pressurized thermal shock (PTS) in a pressurized water reactor (PWR). The code system consists of several member codes to analyse the thermal-mixing behavior of emergency core cooling (ECC) water and primary coolant, transient stress distribution within the vessel wall, and crack growth behavior at the inner surface of the vessel. The crack growth behavior is evaluated by comparing the stress intensity factor (k I ) with the crack initiation toughness (k Ic ) and crack arrest toughness (k Ic ), taking into account the fast neutron irradiation embrittlement. This report describes the methods and models applied in PLES/PTS and the input data requirements. (author)

Line pressure effects on differential pressure measurements

International Nuclear Information System (INIS)

Neff, G.G.; Evans, R.P.

1982-01-01

The performance of differential pressure transducers in experimental pressurized water reactor (PWR) systems was evaluated. Transient differential pressure measurements made using a simple calibration proportionality relating differential pressure to output voltage could have large measurement uncertainties. A more sophisticated calibration equation was derived to incorporate the effects of zero shifts and sensitivity shifts as pressure in the pressure sensing line changes with time. A comparison made between the original calibration proportionality equation and the derived compensation equation indicates that potential measurement uncertainties can be reduced

Early activation of the coagulation system during lower body negative pressure

DEFF Research Database (Denmark)

Zaar, M; Johansson, P I; Nielsen, L B

2009-01-01

We considered that a moderate reduction of the central blood volume (CBV) may activate the coagulation system. Lower body negative pressure (LBNP) is a non-invasive means of reducing CBV and, thereby, simulates haemorrhage. We tested the hypothesis that coagulation markers would increase following...... moderate hypovolemia by exposing 10 healthy male volunteers to 10 min of 30 mmHg LBNP. Thoracic electrical impedance increased during LBNP (by 2.6 +/- 0.7 Omega, mean +/- SD; P pressure decreased (84 +/- 5 to 80...

Evaluation of handwriting kinematics and pressure for differential diagnosis of Parkinson's disease.

Science.gov (United States)

Drotár, Peter; Mekyska, Jiří; Rektorová, Irena; Masarová, Lucia; Smékal, Zdeněk; Faundez-Zanuy, Marcos

2016-02-01

We present the PaHaW Parkinson's disease handwriting database, consisting of handwriting samples from Parkinson's disease (PD) patients and healthy controls. Our goal is to show that kinematic features and pressure features in handwriting can be used for the differential diagnosis of PD. The database contains records from 37 PD patients and 38 healthy controls performing eight different handwriting tasks. The tasks include drawing an Archimedean spiral, repetitively writing orthographically simple syllables and words, and writing of a sentence. In addition to the conventional kinematic features related to the dynamics of handwriting, we investigated new pressure features based on the pressure exerted on the writing surface. To discriminate between PD patients and healthy subjects, three different classifiers were compared: K-nearest neighbors (K-NN), ensemble AdaBoost classifier, and support vector machines (SVM). For predicting PD based on kinematic and pressure features of handwriting, the best performing model was SVM with classification accuracy of Pacc=81.3% (sensitivity Psen=87.4% and specificity of Pspe=80.9%). When evaluated separately, pressure features proved to be relevant for PD diagnosis, yielding Pacc=82.5% compared to Pacc=75.4% using kinematic features. Experimental results showed that an analysis of kinematic and pressure features during handwriting can help assess subtle characteristics of handwriting and discriminate between PD patients and healthy controls. Copyright © 2016 Elsevier B.V. All rights reserved.

Personality as a Moderator of Context Effects on Academic Achievement

Science.gov (United States)

Hendriks, A. A. Jolijn; Kuyper, Hans; Lubbers, Miranda J.; Van der Werf, Margaretha P. C.

2011-01-01

We investigated whether personality moderates group influence of classmates on academic achievement and whether these so-called context effects can be attributed to peer pressure. The sample consisted of 2498 students in their first year of Dutch secondary education. The data were analyzed by a two-level (students within classes) analysis,…

Combustion of High Molecular Weight Hydrocarbon Fuels and JP-8 at Moderate Pressures

Science.gov (United States)

2016-07-26

1. Introduction Fundamental knowledge of mechanisms of autoignition of condensed hydrocarbon fuels at elevated pressures is essential for accurate...particular JP-8) and surrogates of jet-fuels in laminar non-uniform flows at elevated pressures upto 2.5 MPa. Experimental and kinetic modeling studies...AGENCY NAME(S) AND ADDRESS (ES) U.S. Army Research Office P.O. Box 12211 Research Triangle Park, NC 27709-2211 Combustion, Jet Fuels, JP-8, Elevated

Full-scale Mark II CRT program: dynamic response evaluation test of pressure transducers

International Nuclear Information System (INIS)

Kukita, Yutaka; Namatame, Ken; Takeshita, Isao; Shiba, Masayoshi

1982-12-01

A dynamic response evaluation test of pressure transducers was conducted in support of the JAERI Full-Scale Mark II CRT (Containment Response Test) Program. The test results indicated that certain of the cavity-type transducers used in the early blowdown test had undesirable response characteristics. The transducer mounting scheme was modified to avoid trapping of air bubbles in the pressure transmission tubing attached to the transducers. The dynamic response of the modified transducers was acceptable within the frequency range of 200 Hz. (author)

Evaluation of Pressure Changes in HANARO Reactor Hall after a Reactor Shutdown

International Nuclear Information System (INIS)

Han, Geeyang; Han, Jaesam; Ahn, Gukhoon; Jung, Hoansung

2013-01-01

The major objective of this work is intended to evaluate the characteristics of the thermal behavior regarding how the decay heat will be affected by the reactor hall pressure change and the increase of pool water temperature induced in the primary coolant after a reactor shutdown. The particular reactor pool water temperature at the surface where it is evaporated owing to the decay heat resulting in the local heat transfer rate is related to the pressure change response in the reactor hall associated with the primary cooling system because of the reduction of the heat exchanger to remove the heat. The increase in the pool water temperature is proportional to the heat transfer rate in the reactor pool. Consequently, any limit on the reactor pool water temperature imposes a corresponding limit on the reactor hall pressure. At HANARO, the decay heat after a reactor shutdown is mainly removed by the natural circulation cooling in the reactor pool. This paper is written for the safety feature of the pressure change related leakage rate from the reactor hall. The calculation results show that the increase of pressure in the reactor hall will not cause any serious problems to the safety limits although the reactor hall pressure is slightly increased. Therefore, it was concluded that the pool water temperature increase is not so rapid as to cause the pressure to vary significantly in the reactor hall. Furthermore, the mathematical model developed in this work can be a useful analytical tool for scoping and parametric studies in the area of thermal transient analysis, with its proper representation of the interaction between the temperature and pressure in the reactor hall

Subchannel analysis with turbulent mixing rate of supercritical pressure fluid

International Nuclear Information System (INIS)

Wu, Jianhui; Oka, Yoshiaki

2015-01-01

Highlights: • Subchannel analysis with turbulent mixing rate law of supercritical pressure fluid (SPF) is carried out. • Turbulent mixing rate is enhanced, compared with that calculated by the law of pressurized water reactor (PWR). • Increase in maximum cladding surface temperature (MCST) is smaller comparing with PWR model. • The sensitivities of MCST on non-uniformity of subchannel area and power peaking are reduced by using SPF model. - Abstract: The subchannel analysis with turbulent mixing rate law of supercritical pressure fluid (SPF) is carried out for supercritical-pressurized light water cooled and moderated reactor (Super LWR). It is different from the turbulent mixing rate law of pressurized water reactor (PWR), which is widely adopted in Super LWR subchannel analysis study, the density difference between adjacent subchannels is taken into account for turbulent mixing rate law of SPF. MCSTs are evaluated on three kinds of fuel assemblies with different pin power distribution patterns, gap spacings and mass flow rates. Compared with that calculated by employing turbulent mixing rate law of PWR, the increase in MCST is smaller even when peaking factor is large and gap spacing is uneven. The sensitivities of MCST on non-uniformity of the subchannel area and power peaking are reduced

Evaluation of the constant pressure panel method (CPM) for unsteady air loads prediction

Science.gov (United States)

Appa, Kari; Smith, Michael J. C.

1988-01-01

This paper evaluates the capability of the constant pressure panel method (CPM) code to predict unsteady aerodynamic pressures, lift and moment distributions, and generalized forces for general wing-body configurations in supersonic flow. Stability derivatives are computed and correlated for the X-29 and an Oblique Wing Research Aircraft, and a flutter analysis is carried out for a wing wind tunnel test example. Most results are shown to correlate well with test or published data. Although the emphasis of this paper is on evaluation, an improvement in the CPM code's handling of intersecting lifting surfaces is briefly discussed. An attractive feature of the CPM code is that it shares the basic data requirements and computational arrangements of the doublet lattice method. A unified code to predict unsteady subsonic or supersonic airloads is therefore possible.

Proposal of evaluation method of tsunami wave pressure using 2D depth-integrated flow simulation

International Nuclear Information System (INIS)

Arimitsu, Tsuyoshi; Ooe, Kazuya; Kawasaki, Koji

2012-01-01

To design and construct land structures resistive to tsunami force, it is most essential to evaluate tsunami pressure quantitatively. The existing hydrostatic formula, in general, tended to underestimate tsunami wave pressure under the condition of inundation flow with large Froude number. Estimation method of tsunami pressure acting on a land structure was proposed using inundation depth and horizontal velocity at the front of the structure, which were calculated employing a 2D depth-integrated flow model based on the unstructured grid system. The comparison between the numerical and experimental results revealed that the proposed method could reasonably reproduce the vertical distribution of the maximum tsunami pressure as well as the time variation of the tsunami pressure exerting on the structure. (author)

A multicenter, open-label study of the efficacy and safety of telmisartan in mild to moderate hypertensive patients

Directory of Open Access Journals (Sweden)

Plavnik Frida Liane

2002-01-01

Full Text Available OBJECTIVE: To evaluate the efficacy and tolerability of telmisartan, given once a day to patients with mild to moderate hypertension, as well as to assess the 24-hour blood pressure profile with ABPM. METHODS: Initially, 163 patients over 18 were selected, regardless of sex, with blood pressure levels >140/90mmHg at visit 1, which was confirmed at visit 2. One hundred thirty-four patients completed the study. After a 4-week placebo run-in phase, telmisartan 40mg/daily was given for 6 weeks. In those patients whose blood pressure (BP levels were lower than 140/90mmHg, the same dosage was kept for an additional period of 6 weeks. For those who had BP higher than 140/90mmHg, the dosage was increased to 80mg/daily. Sixty-two patients were included in a subgroup that underwent ABPM 3 different times during the study. RESULTS: In the overall group, blood pressure reduction ranged from 162.3±14.5/101.3±5.75 mmHg (baseline to 147.3±20.1/90.8±10.9 mmHg (week 12 (p<0.05. Mean blood pressure decreases were 14.4mmHg for systolic BP and 10.3mmHg for diastolic BP, after 12 weeks of active treatment. A subanalysis showed that 47 (35% patients took telmisartan 40mg throughout the study and 81 (65% had the dosage increased to 80mg daily. Using ABPM, an 8-mmHg reduction in systolic BP as well as a 5-mmHg reduction in diastolic BP were observed, when compared with baseline values in the final 6 hours (18-24 hours after the last dose of study medication. CONCLUSION: Our results confirm that telmisartan given once a day is effective in reducing blood pressure levels in mild to moderate hypertensive patients. This reduction occurs in a sustained and gradual manner during a 24-hour period confirmed by ABPM.

Perceived unfairness at work, social and personal resources, and resting blood pressure.

Science.gov (United States)

Ford, Michael T

2014-02-01

By drawing from theoretical perspectives suggesting that unfair conditions threaten fundamental psychological needs, perceived unfairness at work was proposed and tested as a predictor of resting blood pressure. As part of the Midlife Development in the United States Biomarkers project, participants completed questionnaires measuring perceived unfairness, self-esteem and coworker support. Resting blood pressure readings were also recorded as part of a larger physical examination. Results indicate that perceived unfairness at work was associated with higher resting diastolic and systolic blood pressure. Perceived unfairness was most strongly related to diastolic and systolic blood pressure among women with low levels of coworker support. Contrary to predictions, self-esteem did not moderate the association between perceived unfairness and blood pressure. These results suggest that high blood pressure may be a mechanism linking unfairness to negative health outcomes and point to coworker support as a moderator of the perceived unfairness-blood pressure relationship among women. Further research is needed exploring the mediating mechanisms linking unfair treatment at work to blood pressure and health. Copyright © 2013 John Wiley & Sons, Ltd.

On high-pressure melting of tantalum

Science.gov (United States)

Luo, Sheng-Nian; Swift, Damian C.

2007-01-01

The issues related to high-pressure melting of Ta are discussed within the context of diamond-anvil cell (DAC) and shock wave experiments, theoretical calculations and common melting models. The discrepancies between the extrapolations of the DAC melting curve and the melting point inferred from shock wave experiments, cannot be reconciled either by superheating or solid-solid phase transition. The failure to reproduce low-pressure DAC melting curve by melting models such as dislocation-mediated melting and the Lindemann law, and molecular dynamics and quantum mechanics-based calculations, undermines their predictions at moderate and high pressures. Despite claims to the contrary, the melting curve of Ta (as well as Mo and W) remains inconclusive at high pressures.

Redistribution Principle Approach for Evaluation of Seismic Active Earth Pressure Behind Retaining Wall

Science.gov (United States)

Maskar, A. D.; Madhekar, S. N.; Phatak, D. R.

2017-11-01

The knowledge of seismic active earth pressure behind the rigid retaining wall is very essential in the design of retaining wall in earthquake prone regions. Commonly used Mononobe-Okabe (MO) method considers pseudo-static approach. Recently there are many pseudo-dynamic methods used to evaluate the seismic earth pressure. However, available pseudo-static and pseudo-dynamic methods do not incorporate the effect of wall movement on the earth pressure distribution. Dubrova (Interaction between soils and structures, Rechnoi Transport, Moscow, 1963) was the first, who considered such effect and till date, it is used for cohesionless soil, without considering the effect of seismicity. In this paper, Dubrova's model based on redistribution principle, considering the seismic effect has been developed. It is further used to compute the distribution of seismic active earth pressure, in a more realistic manner, by considering the effect of wall movement on the earth pressure, as it is displacement based method. The effects of a wide range of parameters like soil friction angle (ϕ), wall friction angle (δ), horizontal and vertical seismic acceleration coefficients (kh and kv); on seismic active earth pressure (Kae) have been studied. Results are presented for comparison of pseudo-static and pseudo-dynamic methods, to highlight the realistic, non-linearity of seismic active earth pressure distribution. The current study results in the variation of Kae with kh in the same manner as that of MO method and Choudhury and Nimbalkar (Geotech Geol Eng 24(5):1103-1113, 2006) study. To increase in ϕ, there is a reduction in static as well as seismic earth pressure. Also, by keeping constant ϕ value, as kh increases from 0 to 0.3, earth pressure increases; whereas as δ increases, active earth pressure decreases. The seismic active earth pressure coefficient (Kae) obtained from the present study is approximately same as that obtained by previous researchers. Though seismic earth

Study on neutronics performance of flower shape advanced supercritical water cooled fast reactor with different solid moderators

International Nuclear Information System (INIS)

Yu Tao; Li Zhifeng; Xie Jinsen; Peng Honghua

2015-01-01

The supercritical water cooled fast reactors worked at such harsh condition with high temperature and high pressure, huge hydrogen balance pressure and thermal shock can result in a great loss of hydrogen. The released hydrogen would be out of control under accident situations. K_e_f_f, conversion ratio, moderator temperature effect, Doppler effect and void effect of different material such as ZrH_1_._7, Bp, BeO, C and SiC are discussed. BeO and SiC hold better integrated performance among these materials. Besides, moderators have less effect on the Doppler effect of fuel. (authors)

Structural analysis and evaluation for the design of pressure vessel

International Nuclear Information System (INIS)

Arai, K.; Uragami, K.; Funada, T.; Baba, K.; Kira, T.

1977-01-01

For the design of pressure vessel, the detailed structural analysis such as the fatigue analysis under operating conditions is required by ASME Code or Japanese regulation. Accordingly, it should be verified by the analysis that the design of the pressure vessel is in compliance with the stress limitation defined in the Code or the regulation. However, it was apparent that the analysis is very complicated and takes a lot of time to evaluate in accordance with the Code requirements. Thereupon we developed the computer program by which we can perform the stress analysis with correctness and comparatively in a short period of design work reflecting the calculation results on detailed drawings to be used for fabrication. The computer program is controlled in combination with the system of the design work and out put list of the program can be directly used for the stress analysis report which is issued to customers. In addition to the above computer program, we developed the specific three dimensional finite element computer program to make sure of the structural integrity of the vessel head and flanges which are most complex for the analysis compared with the stress distribution measured by strain gauges on the vessel head and flange. Besides the structural analysis, the fracture mechanics analysis for the purpose of preventing the pressure vessel from the brittle fracture during heat-up and cool-down operation is also important and thereby we showed herein that the pressure vessel is in safety against the brittle fracture for the specified operating conditions. As a result of the above-mentioned analysis, the pressure vessel is designed with safety from the stand-points of the structural intensity and the fracture mechanics. (auth.)

Evaluation of the stress distribution on the pressure vessel head with multi-openings

Energy Technology Data Exchange (ETDEWEB)

Kim, K.S.; Kim, T.W.; Jeong, K.H.; Lee, G.M. [Korea Atomic Energy Research Institute, Taejon (Korea)

1998-06-01

This report discusses and analyzes the stress distribution on the pressure vessel head with multi-openings(3 PSV nozzles, 2 SDS nozzles and 1 Man Way) according to patterns of the opening distance. The pressurizer of Korea Standardized Nuclear Power Plant(Ulchin 3 and 4), which meets requirements of the cyclic operation and opening design defined by ASME code, was used as the basic model for that. Stress changes according to the distance between openings were investigated and the factors which should be considered for the opening design were analyzed. Also, the nozzle loads at Level A, B conditions and internal pressure were applied in order to evaluate changes of head stress distributions due to nozzle loads. (author). 6 refs., 29 figs., 4 tabs.

Pulmonary Artery Wedge Pressure Relative to Exercise Work Rate in Older Men and Women.

Science.gov (United States)

Esfandiari, Sam; Wright, Stephen P; Goodman, Jack M; Sasson, Zion; Mak, Susanna

2017-07-01

An augmented pulmonary artery wedge pressure (PAWP) response may explain exercise intolerance in some humans. However, routine use of exercise hemodynamic testing is limited by a lack of data from normal older men and women. Our objective was to evaluate the exercise PAWP response and the potential for sexual dimorphism in healthy, nondyspneic older adults. Thirty-six healthy volunteers (18 men [54 ± 7 yr] and 18 women [58 ± 6 yr]) were studied at rest (control) and during two stages of semi-upright cycle ergometry, at heart rates of 100 bpm (light exercise) and 120 bpm (moderate exercise). Right heart catheterization was performed to measure pulmonary pressures. The PAWP response to exercise was assessed in context of exercise work rate and body size. At control, PAWP was similar between men and women. Work rates were significantly smaller in women at comparable HR (P exercise, with no further increase at moderate exercise. When indexed to work rate alone or work rate adjusted to body weight and height, the PAWP response at light and moderate exercise was significantly elevated in women compared with men (P exercise. The similar rise in the PAWP response to submaximal exercise occurs despite lower work rate in healthy older women compared with men, even when adjusted for smaller body size. It is important to consider sex in the development of normal reference ranges for exercise hemodynamic testing.

Consequences assessment for fuel channel failure with consequential moderator drain

International Nuclear Information System (INIS)

Wahba, N.N.; Bayoumi, M.H.

2002-01-01

This paper documents the consequences of spontaneous pressure tube/consequential calandria tube rupture followed by the ejection of end fittings (as a result of guillotine failure of pressure tube) leading to the drain of the moderator. The event is postulated to occur in conjunction with an independent failure of Emergency Coolant Injection System (ECIS). The results of the detailed consequence assessments are used to propose a course of action to mitigate the consequences of such an event. A methodology based on a lumped-parameter model was developed to assess the consequences of the postulated event. (author)

Replacement of low pressure reheater and performance evaluation on domestic NPP moisture separator reheater

International Nuclear Information System (INIS)

Choi, Y. S.; Jeong, W. T.; Shon, S. Y.; Kim, M. H.

2003-01-01

Moisture Separator Reheater is one of the most important equipment for the integrity of low pressure turbine and the total efficiency of the nuclear power plant, It supplies the dry steam to low pressure turbine after separation of moisture and reheating the wet steam out of high pressure turbine. This equipment is always operated under severe conditions, therefore it should be carefully maintained for safe operation and operating confidence. After replacement low pressure reheater of moister separator reheater on domestic nuclear power plant, there was MSR performance degradation and vibration of condensate drain line. So I found out root cause and commented a solution, site people modified the equipment. Finally I concluded the performanc of MSR was good condition, after I inspected the equipment and evaluated the performance of MSR

The moderator's moderator

International Nuclear Information System (INIS)

Williamson, G.K.

1990-01-01

A brief account is given of the development of graphite moderators for Magnox and advanced gas cooled reactors. The accident at Windscale in 1957 brought to worldwide attention the importance of irradiation damage in graphite and the consequent storage of Wigner energy. In spite of the Windscale setback, preparations for the civil programme of Magnox reactors went ahead apace. Some of the background to the disastrous Dungeness B tender is presented. In spite of all the difficulties and uncertainties, the graphite in UK reactors has performed well. In all cases, as far as the author is aware, the behaviour of the graphite moderators will not prevent design life being achieved. (author)

Dynamic osseous scintigraphy in the knee hyper-pressure syndromes

International Nuclear Information System (INIS)

Laurin, J.; Jau, P.; Ferro, L.; Fouque, M.

1997-01-01

This retrospective study of 49 patients, carrying an internal mono-compartmental algic syndrome of the knee, determines the place of the dynamical osseous scintigraphy in three times: in comparison with the pan-goniometry (for 42 of them), in the diagnosis of the hyper-pressure syndrome and in the evaluation of its severity. The vascularization is augmented in 10 patients and the sanguinary pool in 14. Forty eight internal compartments exhibit a tracer hyper-fixation at late times. These anomalies have been classified according to their tibial or condylar localization and intensity, than compared with the pan-goniometric values of the deviation, which in case of a varus, entail an over-pressure risk. These comparisons show a good correlation between the hyper-fixation in the sub-chondral band of the internal tibial plateau and a syndrome of hyper-pressure by deviation in varus, whether this hyper-fixation was moderated and isolated or severe or associated to a condylar image; the intensity of the fixation indicates the severity. The tibial fixation intensity is always superior to that of the rest of compartment, what is essential for the differential diagnosis in case of a simple, without hyper-pressure, arthritis, or other pathology. From this exploration stem 8 osteotomies and 1 prosthesis

Needs for evaluated covariance data for reactor pressure vessel dosimetry

International Nuclear Information System (INIS)

Maerker, R.E.; Broadhead, B.L.; Wagschal, J.J.

1992-01-01

This report discusses new methodology for quantifying and then reducing uncertainties in the calculated pressure vessel fluences of a pressurized water reactor (PWR). The technique involves combining the integral results of the calculated and measured PWR surveillance dosimetry activities with the differential data used in the calculations, along with covariances of all the quantities, into a generalized linear least-squares adjustment procedure. Based on analysis of both PWRs and test reactor benchmarks, substantial evidence now exists to support the conclusion that, of all the nuclear as well as non-nuclear differential data considered, ENDF/B-VI values of the total inelastic iron cross sections and their covariances are the most important data controlling the outcome of the adjustment procedure. Predicted adjustments in these cross sections provided the stimulus for new measurements, the results of which impacted the ENDF/B-VI evaluation of iron 56

Long-term effects of maternal diabetes on blood pressure and renal function in rat male offspring.

Directory of Open Access Journals (Sweden)

Jie Yan

Full Text Available AIMS/HYPOTHESIS: Gestational diabetes mellitus (GDM is increasing rapidly worldwide. Previous animal models were established to study consequences of offspring after exposure to severe intrauterine hyperglycemia. In this study we are aiming to characterize the blood pressure levels and renal function of male offspring obtained from diabetic mothers with moderate hyperglycemia. METHODS: We established a rat model with moderate hyperglycemia after pregnancy by a single intraperitoneal injection of streptozotocin (STZ. The male offspring were studied and fed with either normal diet or high salt diet after weaning. Arterial pressure and renal function were measured. RESULTS: Arterial pressure of male offspring increased from 12 weeks by exposure to intrauterine moderate hyperglycemia. At 20 weeks, high salt diet accelerated the blood pressure on diabetic offspring compared to diabetic offspring fed with normal diet. We found offspring exposed to intrauterine moderate hyperglycemia had a trend to have a higher creatinine clearance rate and significant increase of urinary N-acetyl-β-D-glucosaminidase (NAG excretion indicating an early stage of nephropathy progression. CONCLUSIONS/INTERPRETATION: We observed the high blood pressure level and early renal dysfunction of male offspring obtained from diabetic mothers with moderate hyperglycemia. Furthermore, we investigated high salt diet after weaning on offspring exposed to intrauterine hyperglycemia could exacerbate the blood pressure and renal function. Renin angiotensin system (RAS plays an important role in hypertension pathogenesis and altered gene expression of RAS components in offspring with in utero hyperglycemia exposure may account for the programmed hypertension. Therefore, our study provides evidence "fetal programming" of maternal diabetes is critical for metabolic disease development.

Energy Saving High-Capacity Moderate Pressure Carbon Dioxide Storage System, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Our approach to high-pressure carbon dioxide storage will directly address the challenges associated with storage of compressed carbon dioxide - the need to reduce...

KAPP-3 and 4 containment pressure following postulated severe accident along with SAMG implementation

International Nuclear Information System (INIS)

Sharma, Sanjeev Kr.; Bhartia, D.K.; Mohan, Nalini; Malhotra, P.K.; Ghadge, S.G.; Chandra, Umesh

2011-01-01

Containment is an ultimate safety barrier which is designed to enclose whole reactor systems and to prevent the spread of active air-borne fission products. Studies are done to access its performance following severe accident i.e. Loss of Coolant Accident (LOCA) along with failure of Emergency Core Cooling System (ECCS), moderator and calandria vault water cooling system. The accident progression begins with the double ended break in reactor outlet/inlet header with simultaneous failure of ECCS followed by failure of moderator and calandria vault water cooling system. Initially decay heat and metal water reaction energy are assumed to be added to moderator water resulting in boiling of moderator and re-pressurization of containment due to steam addition. Subsequent to moderator boiling, decay heat and metal water reaction energy are assumed to be added to calandria vault water resulting in boiling and re-pressurization of containment due to steam addition. After moderator and calandria vault water have completely boiled off, rapid hydrogen generation would take place due to oxidation of pressure tubes and calandria tubes. In such accident scenario, the core is severely damaged. It will also lead to release of a large quantity of radio nuclides to containment atmosphere. To arrest the progression of accident, which can result in Severe Core damage and large amount of hydrogen production, which could leads to containment failure due to hydrogen deflagration or detonation, application of Severe Accident Management Guidelines (SAMG) has been studied. SAMG involve addition of water to calandria and calandria vault. It would result the boiling of the added water and consequent pressurization of containment. This paper presents the analysis for pressure-temperature of KAPP-3 and 4 containment following the postulated accident along with the application of Severe Accident Management Guidelines (SAMG). SAMG initiated action helps in arresting the progression of core

Moderator behaviour and reactor internals integrity at Atucha I NPP

International Nuclear Information System (INIS)

Berra, S.; Guala, M.; Herzovich, P.; Chocron, M.; Lorenzo, A.; Raffo Calderon, Ma. C. del; Urrutia, G.

1996-01-01

Atucha I is a Pressure Vessel Heavy Water Cooled Heavy Water Moderator Reactor. In this kind of reactor the moderator tank is physically connected to the primary coolant. Since neutron economy requires the moderator to be as cold as possible, it is necessary that even when physically connected, it should have a separated cooling system, which in this case is also used as a feed-water preheater, and also heat mass transfer with primary coolant should be minimized. This condition requires that some reactor internals are designed in principle to last the whole life of the plant. However, in 1988 the failure of one internal produced a 16 month shut down. This incident could have been prevented but the idea that reactor internals would not have failures due to aging was dominant at that time avoiding the early detection of the failure. However, the analysis of the records after the incident showed that some process variables had changed previously to the incident, i.e., power exchanged at the moderator heat exchanger had increased. Since the station restart up some changes in the moderator process variables and a flow rate reduction of about 10% through the primary side of one moderator cooler were observed. In order to understand the flow reduction and the overall behaviour of moderators parameters, two models were developed that predict moderator and moderator cooler behavior under the new conditions. The present paper refers to these models, which together with the improvement of process variables measurements mentioned in another paper presented at this meeting permits to understand current moderator behaviour and helps to early diagnostic of an eventual reactor internal failure. (author). 2 refs, 4 figs, 1 tab

Moderator behaviour and reactor internals integrity at Atucha I NPP

Energy Technology Data Exchange (ETDEWEB)

Berra, S; Guala, M; Herzovich, P [Central Nuclear Atucha I, Nucleoelectrica Argentina, Lima, Buenos Aires (Argentina); Chocron, M; Lorenzo, A; Raffo Calderon, Ma. C. del; Urrutia, G [Comision Nacional de Energia Atomica, Buenos Aires (Argentina). Centro Atomico Constituyentes

1997-12-31

Atucha I is a Pressure Vessel Heavy Water Cooled Heavy Water Moderator Reactor. In this kind of reactor the moderator tank is physically connected to the primary coolant. Since neutron economy requires the moderator to be as cold as possible, it is necessary that even when physically connected, it should have a separated cooling system, which in this case is also used as a feed-water preheater, and also heat mass transfer with primary coolant should be minimized. This condition requires that some reactor internals are designed in principle to last the whole life of the plant. However, in 1988 the failure of one internal produced a 16 month shut down. This incident could have been prevented but the idea that reactor internals would not have failures due to aging was dominant at that time avoiding the early detection of the failure. However, the analysis of the records after the incident showed that some process variables had changed previously to the incident, i.e., power exchanged at the moderator heat exchanger had increased. Since the station restart up some changes in the moderator process variables and a flow rate reduction of about 10% through the primary side of one moderator cooler were observed. In order to understand the flow reduction and the overall behaviour of moderators parameters, two models were developed that predict moderator and moderator cooler behavior under the new conditions. The present paper refers to these models, which together with the improvement of process variables measurements mentioned in another paper presented at this meeting permits to understand current moderator behaviour and helps to early diagnostic of an eventual reactor internal failure. (author). 2 refs, 4 figs, 1 tab.

Promoting sustainability in quality improvement: an evaluation of a web-based continuing education program in blood pressure measurement.

Science.gov (United States)

Block, Lauren; Flynn, Sarah J; Cooper, Lisa A; Lentz, Caroline; Hull, Tammie; Dietz, Katherine B; Boonyasai, Romsai T

2018-01-10

The accuracy of blood pressure measurement is variable in office-based settings. Even when staff training programs are effective, knowledge and skills decay over time, supporting the need for ongoing staff training. We evaluated whether a web-based continuing education program in blood pressure measurement reinforced knowledge and skills among clinical staff and promoted sustainability of an existing quality improvement program. Medical assistants and nurses at six primary care clinics within a health system enrolled in a 30-min online educational program designed to refresh their knowledge of blood pressure measurement. A 20-question pre- and post-intervention survey addressed learners' knowledge and attitudes. Direct observation of blood pressure measurement technique before and after the intervention was performed. Differences in responses to pre- and post-module knowledge and attitudes questions and in observation data were analyzed using chi-square tests and simple logistic regression. All 88 clinical staff members participated in the program and completed the evaluation survey. Participants answered 80.6% of questions correctly before the module and 93.4% afterwards (p blood pressure measurement were high at baseline and did not improve significantly. Prior to the intervention, staff adhered to 9 of 18 elements of the recommended technique during at least 90% of observations. Following the program, staff was more likely to explain the protocol, provide a rest period, measure an average blood pressure, and record the average blood pressure, but less likely to measure blood pressure with the arm at heart level and use the right arm. We designed, implemented, and evaluated a web-based educational program to improve knowledge, skills, and attitudes in blood pressure measurement and use of an automated device among nurses and medical assistants in ambulatory care. The program reinforced knowledge related to recommended blood pressure measurement technique

The effectivty of hydrogeneous moderators in pulsed sources

International Nuclear Information System (INIS)

Rief, H.; Hartman, J.

1975-01-01

Guide lines are provided for an evaluation of the potential of pulsed reactors. In the SORA reactor, neutrons emitted from the fast core are converted in hydrogeneous moderators to beams of low energy neutrons for time of flight experiments. The important characteristics of the neutron sources are absolute intensity of the neutron beam and its energy and time distribution. The problem is solved mathematcially by the random walk (Monte Carlo) method. Calculational methods which are described are compared with pulsed moderator measurements. The choice of moderators and criteria of optimization are discussed. Particular examples of realistic moderator design as planned for SOYA, and as they will be used in pulsed reactors, are analysed, a distinction being made between thermal, cold, and hot moderators. Finally flux estimates are compared with those obtained for a spallation target. (U.K.)

Qualitative Resting Coronary Pressure Wave Form Analysis to Predict Fractional Flow Reserve.

Science.gov (United States)

Matsumura, Mitsuaki; Maehara, Akiko; Johnson, Nils P; Fearon, William F; De Bruyne, Bernard; Oldroyd, Keith G; Pijls, Nico H J; Jenkins, Paul; Ali, Ziad A; Mintz, Gary S; Stone, Gregg W; Jeremias, Allen

2018-03-27

To evaluate the predictability of resting distal coronary pressure wave forms for fractional flow reserve (FFR). Resting coronary wave forms were qualitatively evaluated for the presence of (i) dicrotic notch; (ii) diastolic dipping; and (iii) ventricularization. In a development cohort (n=88) a scoring system was developed that was then applied to a validation cohort (n=428) using a multivariable linear regression model to predict FFR and receiver operating characteristics (ROC) to predict FFR ≤0.8. In the development cohort, all 3 qualitative parameters were independent predictors of FFR. However, in a multivariable linear regression model in the validation cohort, qualitative wave form analysis did not further improve the ability of resting distal coronary to aortic pressure ratio (Pd/Pa) (p=0.80) or instantaneous wave-free ratio (iFR) (p=0.26) to predict FFR. Using ROC, the area under the curve of resting Pd/Pa (0.86 versus 0.86, P=0.08) and iFR (0.86 versus 0.86, P=0.26) did not improve by adding qualitative analysis. Qualitative coronary wave form analysis showed moderate classification agreement in predicting FFR but did not add substantially to the resting pressure gradients Pd/Pa and iFR; however, when discrepancies between quantitative and qualitative analyses are observed, artifact or pressure drift should be considered.

Core Self-Evaluations and Job and Life Satisfaction: The Mediating and Moderated Mediating Role of Job Insecurity.

Science.gov (United States)

Hsieh, Hui-Hsien; Huang, Jie-Tsuen

2017-04-03

This study examined the mediating role of job insecurity in the relationship between core self-evaluations (CSE) and job satisfaction, while also investigating the moderating role of job insecurity in the mediated relationship between CSE and life satisfaction via job satisfaction. Survey data were collected from a sample of 346 full-time employees in Taiwan. We found that job insecurity partially mediated the CSE-job satisfaction relationship. Moreover, we found that job insecurity moderated not only the relationship between CSE and job satisfaction but also the mediated relationship between CSE and life satisfaction via job satisfaction. Specifically, both the CSE-job satisfaction relationship and the CSE-job satisfaction-life satisfaction relationship became stronger when job insecurity was low. Our results emphasize the importance of raising employees' CSE, which is beneficial not only for diminishing their perceptions of job insecurity, but also for boosting their job and life satisfaction. Practical implications and directions for future research are discussed.

Basic data generation and pressure loss coefficient evaluation for HANARO core thermal-hydraulic analyses

International Nuclear Information System (INIS)

Chae, Hee Taek; Lee, Kye Hong

1999-06-01

MATRA-h, a HANARO subchannel analysis computer code, is used to evaluate thermal margin of the HANARO fuel. It's capability includes the assessments of CHF, ONB margin, and fuel temperature. In this report, basic input data and core design parameters required to perform the subchannel analysis with MATRA-h code are collected. These data include the subchannel geometric data, thermal-hydraulic correlations, empirical constants and material properties. The friction and form loss coefficients of the fuel assemblies were determined based on the results of the pressure drop test. At the same time, different form loss coefficients at the end plates and spacers are evaluated for various subchannels. The adequate correlations are applied to the evaluation of the form loss coefficients for various subchannels, which are corrected by measured values in order to have a same pressure drop at each flow channel. These basic input data and design parameters described in this report will be applied usefully to evaluate the thermal margin of the HANARO fuel. (author). 11 refs., 13 tabs., 11 figs

Insomnia complaints in lean patients with obstructive sleep apnea negatively affect positive airway pressure treatment adherence.

Science.gov (United States)

Eysteinsdottir, Bjorg; Gislason, Thorarinn; Pack, Allan I; Benediktsdottir, Bryndís; Arnardottir, Erna S; Kuna, Samuel T; Björnsdottir, Erla

2017-04-01

The objective of this study was to evaluate the determinants of long-term adherence to positive airway pressure treatment among patients with obstructive sleep apnea, with special emphasis on patients who stop positive airway pressure treatment within 1 year. This is a prospective long-term follow-up of subjects in the Icelandic Sleep Apnea Cohort who were diagnosed with obstructive sleep apnea between 2005 and 2009, and started on positive airway pressure treatment. In October 2014, positive airway pressure adherence was obtained by systematically evaluating available clinical files (n = 796; 644 males, 152 females) with moderate to severe obstructive sleep apnea (apnea-hypopnea index ≥15 events per h). The mean follow-up time was 6.7 ± 1.2 years. In total, 123 subjects (15.5%) returned their positive airway pressure device within the first year, 170 (21.4%) returned it later and 503 (63.2%) were still using positive airway pressure. The quitters within the first year had lower body mass index, milder obstructive sleep apnea, less sleepiness, and more often had symptoms of initial and late insomnia compared with long-term positive airway pressure users at baseline. Both initial and late insomnia were after adjustment still significantly associated with being an early quitter among subjects with body mass index insomnia are associated with early quitting on positive airway pressure among non-obese subjects. © 2016 European Sleep Research Society.

Evaluation of thermal properties of food materials at high pressures using a dual-needle line-heat-source method.

Science.gov (United States)

Zhu, S; Ramaswamy, H S; Marcotte, M; Chen, C; Shao, Y; Le Bail, A

2007-03-01

Thermal properties of food systems at high pressure (HP) are important in the design and operation of HP processing equipment. Available techniques for thermal property evaluation under HP conditions are still very limited. In this study, a dual-needle line-heat-source (DNL) device was installed in an HP vessel to evaluate thermal conductivity (k), diffusivity (alpha), and volumetric heat capacity (C(pV)) of foods at high pressure. The DNL probe was calibrated using glycerin (0.1 MPa) and 2% (w/w) agar gel (0.1 to 350 MPa) at 5 and 25 degrees C. Calibration results showed a good correlation with the reference data of pure water: R(2)= 0.966 for thermal conductivity and R(2)= 0.837 for diffusivity, and a small standard deviation of relative error (3.18%) for the volumetric heat capacity. Fresh potato and cheddar cheese were used as test samples at 5 degrees C at selected pressure levels (0.1 to 350 MPa). The potato samples gave thermal properties very close to those of pure water, but much higher than those of the cheese. The k and alpha values of both potato and cheese increased with pressure and a 2nd-order polynomial well fitted their pressure dependency. The volumetric heat capacity data did not show a clear pressure-dependency trend. The experimental system worked well for the evaluation of thermal properties at pressures up to 350 MPa.

Evaluation of local allowable wall thickness of thinned pipe considering internal pressure and bending moment

International Nuclear Information System (INIS)

Kim, J. W.; Park, C. Y.; Kim, B. Y.

2000-01-01

This study proposed the local allowable wall thickness (LAWT) evaluation method for local wall thinned pipe subjected by internal pressure and bending moment. Also, LAWT was evaluated for simplified thinned pipe and the effect of axial extent of thinned area on LAWT was investigated. The results showed that LAWT predicted by present method was thinner, about 50%, than that evaluated by construction code and ASME Code Case N-597, while it was thicker, about 2 times, than that calculated by evaluation model based on pipe experiments. LAWT decreased with increasing axial extent of thinned area and was saturated above axial extent of pipe radius, which was a contrast to the results of ASME Code Case N-597 evaluation. The results of stress analysis with applied loading type indicated that the effect of axial extent of thinned area on LAWT was dependent on loading type considering in the evaluation. That is, the dependence of axial extent on LAWT is determined by magnitude of bending moment, and the contrary trend with axial extent in ASME Code Case is because ASME Code Case N-597 considers only internal pressure in the evaluation

[Injection Pressure Evaluation of the New Venous Catheter with Side Holes for Contrast-enhanced CT/MRI].

Science.gov (United States)

Fukuda, Junya; Arai, Keisuke; Miyazawa, Hitomi; Kobayashi, Kyouko; Nakamura, Junpei; Suto, Takayuki; Tsushima, Yoshito

2018-01-01

The simulation study was conducted for the new venous catheter with side holes of contrast-enhanced computed tomography (CT) and magnetic resonance imaging (MRI) to evaluate the infusion pressure on four contrast media and several injection speeds. All infusion pressure of the new venous catheter with side holes were less than 15 kg/cm 2 as limitation of extension tube and also reduced the infusion pressure by 15% at the maximum compared to the catheter with single hole. The results suggest that the new venous catheter with side holes can reduce the infusion pressure by power injection of contrast-enhanced CT and MRI.

An evaluation of the process used to determine life orientation moderation in school based asssessments for Grade twelve

OpenAIRE

2013-01-01

M. Ed. (Higher Education) This study seeks to evaluate the processes used in the moderation of School-based Assessment (SBA) in Life Orientation (LO). This subject has been introduced by the Department of Education (DoE) to form part of Grade 12 exit examinations the National Curriculum Statement (NCS). SBA refers to all assessment that is conducted by teachers, and sometimes is known as internal assessment, coursework or continuous assessment...

Laser therapy in pressure ulcers: evaluation by the Pressure Ulcer Scale for Healing and Nursing Outcomes Classification

Directory of Open Access Journals (Sweden)

Sofia Palagi

2015-10-01

Full Text Available AbstractOBJECTIVETo describe the pressure ulcer healing process in critically ill patients treated with conventional dressing therapy plus low-intensity laser therapy evaluated by the Pressure Ulcer Scale for Healing (PUSH and the result of Wound Healing: Secondary Intention, according to the Nursing Outcomes Classification (NOC.METHODCase report study according to nursing process conducted with an Intensive Care Unit patient. Data were collected with an instrument containing the PUSH and the result of the NOC. In the analysis we used descriptive statistics, considering the scores obtained on the instrument.RESULTSA reduction in the size of lesions of 7cm to 1.5cm of length and 6cm to 1.1cm width, in addition to the increase of epithelial tissue and granulation, decreased secretion and odor.CONCLUSIONThere was improvement in the healing process of the lesion treated with adjuvant therapy and the use of NOC allowed a more detailed and accurate assessment than the PUSH.

Technical Evaluation Report. 54. Best Practices in Synchronous Conferencing Moderation

Science.gov (United States)

Anderson, Lynn; Fyvie, Barb; Koritko, Brenda; McCarthy, Kathy; Paz, Sonia Murillo; Rizzuto, Mary; Tremblay, Remi; Sawyers, Urel

2006-01-01

Practical guidelines are offered for the use of synchronous online conferencing software by session administrators and moderators. The configuration of the software prior to conferencing sessions is discussed, and the planning and implementation of useful collaborative activities such as "synchronised browsing." The combination of these…

The first Iranian recommendations on prevention, evaluation and management of high blood pressure

Directory of Open Access Journals (Sweden)

Feridoun Noohi

2012-10-01

Full Text Available This paper presents the complete report of the first Iranian Recommendations on Prevention, Evaluation and Management of High Blood Pressure. The purpose is to provide an evidence-based approach to the prevention, management and control of hypertension (HTN by adapting the most internationally known and used guidelines to the local health care status with consideration of the currently available data and based on the locally conducted researches on HTN as well as social and health care requirements. A working group of national and international experts participated in discussions and collaborated in decision-making, writing and reviewing the whole report. Multiple subcommittees worked together to review the recent national and international literature on HTN in different areas. We used the evaluation tool that is called “AGREE” and considered a score of > 60% as a high score. We adapted the Canadian Hypertension Education Program (CHEP, the United Kingdom’s National Institute for Health and Clinical Excellence (NICE and the US-based joint National Committee on Prevention, Detection, Evaluation and Treatment of High Blood Pressure (JNC7. The key topics that are highlighted in this report include: The importance of ambulatory and self-measurement of blood pressure, evaluation of cardiovascular risk in HTN patients, the role of lifestyle modification in the prevention of HTN and its control with more emphasis on salt intake reduction and weight control, introducing pharmacotherapy suitable for uncomplicated HTN or specific situations and the available drugs in Iran, highlighting the importance of angiotensin-converting enzyme inhibitors, angiotensin-receptor blockers and calcium channel blockers as the first line therapy in many situations, the non-use of beta blockers as the first time treatment except in specific conditions, treating HTN in women, children, obese and elderly patients, the patient compliance to improve HTN control, practical

Performance evaluation of reactor operated zircaloy-2 pressure tubes of RAPS-1

International Nuclear Information System (INIS)

Chatterjee, S.; Ramadasan, E.; Balakrishnan, K.S.; Bahl, J.K.

1992-01-01

Detailed post irradiation examination was carried out on pressure tube sections from E-10, F-9 and F-10 locations of RAPS-1 after an in-reactor residence equivalent to 3.6 effective full power years. The F-10 pressure tube was studied in detail on sections obtained from one end to the other, whereas in the case of E-9 and F-9 pressure tubes only the end sections were examined. The studies carried out were visual examination, metallography, hydrogen i.e. H(D) analysis and mechanical testing at 300 C. Microstructural observations revealed uniform and random hydride/deuteride platelet distribution and absence of blisters or hydride segregation. The H(D) content in the F-10 pressure tube was found to vary in the range 6-12 ppm. The typical H(D) content in the three tubes was around 1 ppm. The H(D) pick-up evaluated from the observed oxide layer thickness was 8 ppm. Longitudinal tensile specimens fabricated from the F-10 pressure tube section and tested at 300 C exhibited increase in yield strength and tensile strength of 39% and 30% respectively. The residual uniform elongation was typically 1.8%. The observed changes in the tensile properties were found to be lower than those reported on unstressed specimens irradiated to similar neutron fluences. The observed hydrogen content and tensile properties obtained in F-10 pressure tube would not be detrimental under normal reactor operating conditions. (author). 10 refs., 4 figs., 2 tabs., 1 annexure

Evaluating piezo-electric transducer response to thermal shock from in-cilinder pressure data

NARCIS (Netherlands)

Baert, R.S.G.; Rosseel, E.; Sierens, R.

1999-01-01

One of the major effects limiting the accuracy of piezoelectric transducers for performing in-cylinder pressure measurements is their sensitivity to the cyclic thermal loading effects of the intermittent combustion process. This paper compares five different methods for evaluating the effect of this

Energetic evaluation of high pressure PEM electrolyzer systems for intermediate storage of renewable energies

International Nuclear Information System (INIS)

Bensmann, B.; Hanke-Rauschenbach, R.; Peña Arias, I.K.; Sundmacher, K.

2013-01-01

Three pathways for high pressure hydrogen production by means of water electrolysis are energetically compared. Besides the two classic paths, comprising either the pressurization of the product gas (path I) or the mechanical pressurization of the feed water (path II), a third path is discussed. It involves the electrochemical co-compression during the electrolysis. The energetic evaluation is based on a uniform model description of the different hydrogen production pathways. It consists of integral, steady-state balances for energy, entropy and mass as well as a modern equation of state. From this the reversible energy demand is used to identify the inherent thermodynamic drawbacks of the pathways. The additional consideration of irreversibilities allows for the determination of efficiency losses due to device specific characteristics. For hydrogen delivery pressures of up to 40 bar the classical pathways are out-performed by path III. Since the hydrogen is already produced at elevated pressure this eliminates the need for an energy consuming mechanical hydrogen compression and spares the additional energy demand due to the oxygen pressurization. However, with increasing pressure differences the hydrogen back-diffusion strongly decreases the Faradaic efficiency of the asymmetric electrolyzer that has to be compensated by an additional energy supply

Flow Control Device Evaluation for an Internal Flow with an Adverse Pressure Gradient

Science.gov (United States)

Jenkins, Luther N.; Gorton, Susan Althoff; Anders, Scott G.

2002-01-01

The effectiveness of several active and passive devices to control flow in an adverse pressure gradient with secondary flows present was evaluated in the 15 Inch Low Speed Tunnel at NASA Langley Research Center. In this study, passive micro vortex generators, micro bumps, and piezoelectric synthetic jets were evaluated for their flow control characteristics using surface static pressures, flow visualization, and 3D Stereo Digital Particle Image Velocimetry. Data also were acquired for synthetic jet actuators in a zero flow environment. It was found that the micro vortex generator is very effective in controlling the flow environment for an adverse pressure gradient, even in the presence of secondary vortical flow. The mechanism by which the control is effected is a re-energization of the boundary layer through flow mixing. The piezoelectric synthetic jet actuators must have sufficient velocity output to produce strong longitudinal vortices if they are to be effective for flow control. The output of these devices in a laboratory or zero flow environment will be different than the output in a flow environment. In this investigation, the output was higher in the flow environment, but the stroke cycle in the flow did not indicate a positive inflow into the synthetic jet.

Functional outcome of tibial fracture with acute compartment syndrome and correlation to deep posterior compartment pressure.

Science.gov (United States)

Goyal, Saumitra; Naik, Monappa A; Tripathy, Sujit Kumar; Rao, Sharath K

2017-05-18

To measure single baseline deep posterior compartment pressure in tibial fracture complicated by acute compartment syndrome (ACS) and to correlate it with functional outcome. Thirty-two tibial fractures with ACS were evaluated clinically and the deep posterior compartment pressure was measured. Urgent fasciotomy was needed in 30 patients. Definite surgical fixation was performed either primarily or once fasciotomy wound was healthy. The patients were followed up at 3 mo, 6 mo and one year. At one year, the functional outcome [lower extremity functional scale (LEFS)] and complications were assessed. Three limbs were amputated. In remaining 29 patients, the average times for clinical and radiological union were 25.2 ± 10.9 wk (10 to 54 wk) and 23.8 ± 9.2 wk (12 to 52 wk) respectively. Nine patients had delayed union and 2 had nonunion who needed bone grafting to augment healing. Most common complaint at follow up was ankle stiffness (76%) that caused difficulty in walking, running and squatting. Of 21 patients who had paralysis at diagnosis, 13 (62%) did not recover and additional five patients developed paralysis at follow-up. On LEFS evaluation, there were 14 patients (48.3%) with severe disability, 10 patients (34.5%) with moderate disability and 5 patients (17.2%) with minimal disability. The mean pressures in patients with minimal disability, moderate disability and severe disability were 37.8, 48.4 and 58.79 mmHg respectively ( P fractures causes severe functional disability in majority of patients. These patients are prone for delayed union and nonunion; however, long term disability is mainly because of severe soft tissue contracture. Intra-compartmental pressure (ICP) correlates with functional disability; patients with relatively high ICP are prone for poor functional outcome.

Are Some Countries More Prone to Pressure Evaluators than Others? Comparing Findings from the United States, United Kingdom, Germany, and Switzerland

Science.gov (United States)

Pleger, Lyn; Sager, Fritz; Morris, Michael; Meyer, Wolfgang; Stockmann, Reinhard

2017-01-01

Pressure on evaluators has been investigated recently by surveys in the USA, the UK, Germany, and Switzerland. This study compares the results of those studies regarding pressure on evaluators in different countries. The findings suggest that independence of evaluations does not exist for many respondents. Moreover, the person who commissioned the…

Failure assessment and evaluation of critical crack length for a fresh Zr-2 pressure tube of an Indian PHWR

International Nuclear Information System (INIS)

Krishnan, Suresh; Bhasin, Vivek; Kushwaha, H.S.; Mahajan, S.C.; Kakodkar, A.

1996-01-01

Fracture analysis of Zr-2 pressure tubes having through wall axial crack was done using finite element method. The analysis was done for tubes in as received condition. During reactor operation the mechanical properties of Zr-2 undergo changes. The analysis is valid for pressure tubes of newly commissioned reactors. The main aim of the study was to determine critical crack length of pressure tubes in normal operating conditions. Elastic plastic fracture analysis was done for different crack lengths to determine applied J-integral values. Tearing modulus instability concept was used to evaluate critical crack length. One of the important parameter studied was, the effect of crack face pressure, which leaking fluid exert on the crack faces/lips of through wall axial crack. Its effect was found to be significant for pressure tubes. It increases the applied J-integral values. Approximate analytical solutions which takes into account the plasticity ahead of crack tip, are available and widely used. These formulae do not take into account the crack face pressure. Since, for the present situation the effect of crack face pressure is significant hence, detailed finite analysis was necessary. Detailed 3D finite element analysis gives an insight into the variation of J-integral values over the thickness of pressure tube. It was found that J values are maximum at the middle layer of the tube. A peak factor on J values was defined and evaluated as ratio of maximum J to average J across the thickness, crack opening area for each length was also evaluated. The knowledge of crack opening area is useful for leak before break studies. The failure assessment was also done using Central Electricity Generating Board (CEGB) R-6 method considering the ductile tearing. The reserve factors (or safety margins) for different crack lengths was evaluated using R-6 method. (author). 30 refs., 21 figs., 34 tabs

Effectiveness of an e-learning tool for education on pressure ulcer evaluation.

Science.gov (United States)

Morente, Laura; Morales-Asencio, José M; Veredas, Francisco J

2014-07-01

To evaluate the effectiveness of information and communication technologies in the undergraduate students' pressure ulcer training as a learning tool, compared with traditional teaching methods. Pressure ulcers constitute one of the great challenges faced by nursing professionals. Currently, pressure ulcer training is based on traditional on-campus teaching, involving lecture-style classes with frequent use of photographs of the wounds. This traditional training has some important weaknesses that can put the efficacy of the training at risk. A randomised controlled trial was developed including undergraduate nursing students. The intervention group used an adaptive self-learning e-learning tool developed by the research team (ePULab) for pressure ulcer assessment and treatment. The control group received a traditional on-campus class on the same topic. Pretest and post-test questionnaires were designed to assess the students' ability in pressure ulcer diagnosis and treatment. The educational intervention based on the use of the ePULab tool produced significantly better learning acquisition results than those obtained by traditional lecture-style classes: the total score improved in the control group from 8·23 (SD 1·23)-11·6 (SD 2·52) after the lecture, whereas in the intervention group, the knowledge score changed from 8·27 (SD 1·39)-15·83 (SD 2·52) (p = 0·01) with the use of ePULab. The results show a higher effectiveness of the devised e-learning approach for education on management of pressure ulcers. Our results reveal the suitability of the ePULab e-learning tool as an effective instrument for training on assessment of and treatment for pressure ulcers and its potential impact on clinical decision-making. © 2013 John Wiley & Sons Ltd.

Reproducibility of heart rate variability, blood pressure variability and baroreceptor sensitivity during rest and head-up tilt

DEFF Research Database (Denmark)

Højgaard, Michael V; Agner, Erik; Kanters, Jørgen K

2005-01-01

OBJECTIVE: Previous studies have indicated moderate-to-poor reproducibility of heart rate variability (HRV) but the reproducibility of blood pressure variability (BPV) and spectral measures of baroreceptor sensitivity (BRS) are not well established. METHODS: We measured normal-to-normal heart beat...... pressures were extracted for the assessment of day-to-day and short-term reproducibility. Power spectrum analysis (Fourier) and transfer function analysis was performed. Reproducibility was assessed using the coefficient of variation (CV). The reproducibility of the mean RR interval, mean systolic......, diastolic and mean blood pressure was good (CVspectral parameters of HRV (CV range 18-36%) and BPV (16-44%) and moderate reproducibility of BRS (14-20%). CONCLUSION: Spectral estimates of BRS had only moderate reproducibility although...

Economic and safety aspects of using moderator heat for feed water heating in a nuclear power plant

International Nuclear Information System (INIS)

Patwegar, I.A.; Dutta, Anu; Chaki, S.K.; Venkat Raj, V.

2002-01-01

Full text: In the proposed advanced heavy water reactor (AHWR), coolant and moderator are separated by the coolant channel. The coolant absorbs most of the fission heat produced in the reactor core. However, the moderator absorbs about 5 to 6 % of the fission heat. In a reactor producing 750 MW(th) power, this moderator heat is about 40 MW. In the present Indian PHWR (pressurized heavy water reactor) systems, this moderator heat is lost to a sink through the moderator heat exchangers, which are cooled by process water. This paper presents the results of the steam cycle analysis carried out for AHWR using moderator heat exchangers as part of the feed heating system. The present study is an attempt to determine the gain in electrical output (MW) if moderator heat is utilized for feed water heating. The operational and safety aspects of using moderator heat are also discussed in the paper

Process evaluation of a cluster-randomised trial testing a pressure ulcer prevention care bundle: a mixed-methods study.

Science.gov (United States)

Roberts, Shelley; McInnes, Elizabeth; Bucknall, Tracey; Wallis, Marianne; Banks, Merrilyn; Chaboyer, Wendy

2017-02-13

As pressure ulcers contribute to significant patient burden and increased health care costs, their prevention is a clinical priority. Our team developed and tested a complex intervention, a pressure ulcer prevention care bundle promoting patient participation in care, in a cluster-randomised trial. The UK Medical Research Council recommends process evaluation of complex interventions to provide insight into why they work or fail and how they might be improved. This study aimed to evaluate processes underpinning implementation of the intervention and explore end-users' perceptions of it, in order to give a deeper understanding of its effects. A pre-specified, mixed-methods process evaluation was conducted as an adjunct to the main trial, guided by a framework for process evaluation of cluster-randomised trials. Data was collected across eight Australian hospitals but mainly focused on the four intervention hospitals. Quantitative and qualitative data were collected across the evaluation domains: recruitment, reach, intervention delivery and response to intervention, at both cluster and individual patient level. Quantitative data were analysed using descriptive and inferential statistics. Qualitative data were analysed using thematic analysis. In the context of the main trial, which found a 42% reduction in risk of pressure ulcer with the intervention that was not significant after adjusting for clustering and covariates, this process evaluation provides important insights. Recruitment and reach among clusters and individuals was high, indicating that patients, nurses and hospitals are willing to engage with a pressure ulcer prevention care bundle. Of 799 intervention patients in the trial, 96.7% received the intervention, which took under 10 min to deliver. Patients and nurses accepted the care bundle, recognising benefits to it and describing how it enabled participation in pressure ulcer prevention (PUP) care. This process evaluation found no major failures

Effectiveness of a guided self-help manual in strengthening resilience in people diagnosed with moderate depression and their family caregivers in Thailand: a randomised controlled trial

OpenAIRE

McCann, Terence; Songprakun, Wallapa; Stephenson, John

2017-01-01

The growing incidence of depression in developing countries, such as Thailand, is placing increasing pressure on public mental health services, and those living in rural areas have limited access to mental health services and specialised support. Resilience is integral to the recovery of people with depression and to caregivers. This parallel group randomised controlled trial evaluated the effectiveness of a guided self-help manual in improving resilience in adults diagnosed with moderate dep...

Pressure ulcers management: an economic evaluation.

Science.gov (United States)

Foglia, E; Restelli, U; Napoletano, A M; Coclite, D; Porazzi, E; Bonfanti, M; Croce, D

2012-03-01

Pressure ulcer management represents a growing problem for medical and social health care systems all over the world, particularly in European Union countries where the incidence of pressure ulcers in older persons (> 60 years of age) is predicted to rise. The aim of this study was to provide evidence for the lower impact on economic resources of using advanced dressings for the treatment of pressure ulcers with respect to conventional simple dressings. Two different models of analysis, derived from Activity Based Costing and Health Technology Assessment, were used to measure, over a 30-day period, the direct costs incurred by pressure ulcer treatment for community-residing patients receiving integrated home care. Although the mean cost per home care visit was higher in the advanced dressings patient group than in the simple dressings patient one (E 22.31 versus E 16.03), analysis of the data revealed that the cost of using advanced dressings was lower due to fewer home care visits (22 versus 11). The results underline the fact that decision-makers need to improve their understanding of the advantages of taking a long-term view with regards to the purchase and use of materials. This could produce considerable savings of resources in addition to improving treatment efficacy for the benefit of patients and the health care system.

Evaluated Plan Stress Of Weld In Pressure Tube Using X Ray Diffraction Technique

International Nuclear Information System (INIS)

Phan Trong Phuc; Nguyen Duc Thanh; Luu Anh Tuyen

2011-01-01

X ray diffraction is a fundamental technique measuring stress, this technique has determined crystal strain in materials, from that determined stress in materials. This paper presents study of evaluating plane stress of weld in pressure tube, using modern XRD apparatus: X Pert Pro. (author)

Calculation of the Thermal State of the Graphite Moderator of the RBMK Reactor

Directory of Open Access Journals (Sweden)

Vorobiev Alexander V.

2017-01-01

Full Text Available This work is devoted to study the temperature field of the graphite stack of the RBMK reactor. In work was analyzed the influence of contact pressure between the components of the masonry on the temperature of the graphite moderator.

A controlled evaluation of oral screen effects on intra-oral pressure curve characteristics.

Science.gov (United States)

Knösel, Michael; Jung, Klaus; Kinzinger, Gero; Bauss, Oskar; Engelke, Wilfried

2010-10-01

The purpose of this study was to quantify the impact of oral screen (OS) application on intra-oral pressure characteristics in three malocclusion groups. Fifty-six randomly recruited participants (26 males and 30 females) who met the inclusion criteria of either an Angle Class I occlusal relationships or Angle Class II1 or II2 malocclusions, were assigned by dentition to group I (n = 31), group II1 (n = 12), or group II2 (n = 13). Two 3 minute periods of intra-oral pressure monitoring were conducted on each participant, using two different oral end fittings connected to a piezo-resistive relative pressure sensor: (1) a flexible OS and (2) a small-dimensioned air-permeable end cap (EC), which was placed laterally in the premolar region, thus recording intra-oral pressure independent of the influence of the OS. Pressure curve characteristics for both periods and between the malocclusion groups were evaluated with reference to the frequency of swallowing peaks, duration, and altitude of negative pressure plateau phases and the area under the pressure curve. Statistical analysis was undertaken using analysis of variance (ANOVA), the Wilcoxon Mann-Whitney test, and spearman correlation coefficient. A median number of two peaks (median height -20.9 mbar) and three plateau phases (median height of -2.3 mbar) may be regarded as normative for normal occlusion subjects during a 3 minute period, at rest. OS application raised the median average duration and height of intra-oral negative pressure plateau phases in the II1 subjects, exceeding those of group I, but less than the plateau duration in group II2. Median peak heights were distinctively lower in groups I and II1 during OS application. It is concluded that additional training for extension of intra-oral pressure phases may be a promising approach to pre-orthodontic Class II division 1 treatment.

Evaluation of pressure transducers to measure surface level in the waste storage tanks

International Nuclear Information System (INIS)

Peters, T.J.; Colson, J.B.

1994-06-01

This report describes the results of tests conducted at the Pacific Northwest Laboratory (PNL) to determine if pressure transducers can be used to measure the surface level in the waste tanks. A survey was first conducted to evaluate which, if any, commercially available pressure transducers were available that could meet the requirements for use in the waste tanks. More than 35 companies were contacted to determine if they manufactured a pressure transducer that could be used in the 101-SY waste tank. The three basic requirements for a pressure transducer for this application were that they were radiation-hardened, could withstand a caustic environment, and were certified to be intrinsically safe. No manufacturer was able to meet all three of these requirements with a commercially available product. Seven companies were able to meet the requirements for being radiation-hardened and being able to withstand the caustic environment. However, only two of the nine companies were willing to supply a pressure transducer for laboratory testing. The two pressure transducers that were tested in this program were the VEGA D36-38 from HiTech Technologies, Inc., and the KP-1911-A from Kaman Instrumentation Corporation. Pressure transducers operate on the principle that the pressure at the location of a sensor increases directly with the depth of the liquid above it. A liquid is required in order for these devices to operate. For these tests, water was first used to determine the ideal operation of the devices, then the devices were placed in a 101-SY waste tank simulant. The simulant had a specific gravity of 1.96 and had the consistency similar to the convective layer in the 101-SY waste tank. In order to determine the surface level with pressure transducers, the density of the material needs to be known

Benefits of Moderate-Intensity Exercise during a Calorie-Restricted Low-Fat Diet

Science.gov (United States)

Apekey, Tanefa A.; Morris, A. E. J.; Fagbemi, S.; Griffiths, G. J.

2012-01-01

Objective: Despite the health benefits, many people do not undertake regular exercise. This study investigated the effects of moderate-intensity exercise on cardiorespiratory fitness (lung age, blood pressure and maximal aerobic power, VO[subscript 2]max), serum lipids concentration and body mass index (BMI) in sedentary overweight/obese adults…

Moderator temperature coefficient in BWR core

International Nuclear Information System (INIS)

Naito, Yoshitaka

1977-01-01

Temperature dependences of infinite multiplication factor k sub(infinity) and neutron leakage from the core must be examined for estimation of moderator temperature coefficient. Temperature dependence on k sub(infinity) has been investigated by many researchers, however, the dependence on neutron leakage of a BWR with cruciformed control rods has hardly been done. Because there are difficulties and necessity on calculations of three space dimensional and multi-energy groups neutron distribution in a BWR core. In this study, moderator temperature coefficients of JPDR-II (BWR) core were obtained by calculation with DIFFUSION-ACE, which is newly developed three-dimensional multi-group computer code. The results were compared with experimental data measured from 20 to 275 0 C of the moderator temperature and the good agreement was obtained between calculation and measurement. In order to evaluate neutron leakage from the core, the other two calculations were carried out, adjusting criticality by uniform absorption rate and by material buckling. The former underestimated neutron leakage and the latter overestimated it. Discussion on the results shows that in order to estimate the temperature coefficient of BWR, neutron leakage must be evaluated precisely, therefore the calculation at actual pattern of control rods is necessary. (auth.)

Evaluation of heat transfer coefficient of tungsten filaments at low pressures and high temperatures

International Nuclear Information System (INIS)

Chondrakis, N.G.; Topalis, F.V.

2011-01-01

The paper presents an experimental method for the evaluation of the heat transfer coefficient of tungsten filaments at low pressures and high temperatures. For this purpose an electrode of a T5 fluorescent lamp was tested under low pressures with simultaneous heating in order to simulate the starting conditions in the lamp. It was placed in a sealed vessel in which the pressure was varied from 1 kM (kilo micron) to 760 kM. The voltage applied to the electrode was in the order of the filament's voltage of the lamp at the normal operation with the ballast during the preheating process. The operating frequency ranged from DC to 50 kHz. The experiment targeted on estimating the temperature of the electrode at the end of the first and the ninth second after initiating the heating process. Next, the heat transfer coefficient was calculated at the specific experimental conditions. A mathematical model based on the results was developed that estimates the heat transfer coefficient. The experiments under different pressures confirm that the filament's temperature strongly depends on the pressure.

Thermal analysis of CANDU6 moderator system for loss of cooling

International Nuclear Information System (INIS)

Xu Zhen

2012-01-01

The coolant system and moderator system of CANDU6 are independent. The prompt neutrons are moderated as thermal neutrons by the moderator and the continuous nuclear fission in the reactor is maintained. At the same time the moderator system supplies the heat sink for the heat produced by the neutrons moderation. During the in-service maintenance of plant, the standby RCW which will only cool down reactor coolant system operates instead of RCW and can not supply heat sink for moderator system heat exchanger. As the result, the moderator system will lose heat sink during the operation of standby RCW. To estimate the moderator temperature, the thermal analysis of moderator system for loss of cooling was compared with the experiment data and the system failure caused by the temperature raising was evaluated in this paper. (author)

Pressure ulcers prevention efficacy of an alternating pressure air mattress in elderly patients: E²MAO a randomised study.

Science.gov (United States)

Sauvage, P; Touflet, M; Pradere, C; Portalier, F; Michel, J-M; Charru, P; Passadori, Y; Fevrier, R; Hallet-Lezy, A-M; Beauchêne, F; Scherrer, B

2017-06-02

Our aim was to compare Axtair One, an alternating pressure air mattress (APAM), with a viscoelastic foam mattress (VFM) in elderly patients at moderate to high risk of developing pressure ulcers (PUs). A randomised, controlled, superiority, parallel-group, open-label, multicentre study, was conducted, between February 2012 and March 2015, in nine French, medium- and long-term stay facilities. Eligible patients were aged 70 and over, had no PUs on enrolment, were bedridden for at least 15 hours per day, had reduced mobility, an absent or minimal positioning capability, a Braden score 12 and a Karnofsky score elderly patients, bedridden for more than 15 hours per day, severely dependent, at moderate-to high-risk of PUs, with an instantaneous risk for the appearance of PUs 7.57 times greater in the VFM group than in the APAM group. This study provides descriptive information and evidence for practice.

High spatial resolution pressure distribution of the vaginal canal in Pompoir practitioners: A biomechanical approach for assessing the pelvic floor.

Science.gov (United States)

Cacciari, Licia P; Pássaro, Anice C; Amorim, Amanda C; Sacco, Isabel C N

2017-08-01

Pompoir is a technique poorly studied in the literature that claims to improve pelvic floor strength and coordination. This study aims to investigate the pelvic floor muscles' coordination throughout the vaginal canal among Pompoir practitioners and non-practitioners by describing a high resolution map of pressure distribution. This cross-sectional, study included 40 healthy women in two groups: control and Pompoir. While these women performed both sustained and "waveform" pelvic floor muscle contractions, the spatiotemporal pressure distribution in their vaginal canals was evaluated by a non-deformable probe fully instrumented with a 10×10 matrix of capacitive transducers. Pompoir group was able to sustain the pressure levels achieved for a longer period (40% longer, moderate effect, P=0.04). During the "waveform" contraction task, Pompoir group achieved lower, earlier peak pressures (moderate effect, P=0.05) and decreased rates of contraction (small effect, P=0.04) and relaxation (large effect, P=0.01). During both tasks, Pompoir group had smaller relative contributions by the mid-region and the anteroposterior planes and greater contributions by the caudal and cranial regions and the latero-lateral planes. Results suggest that specific coordination training of the pelvic floor muscles alters the pressure distribution profile, promoting a more-symmetric distribution of pressure throughout the vaginal canal. Therefore, this study suggests that pelvic floor muscles can be trained to a degree beyond strengthening by focusing on coordination, which results in changes in symmetry of the spatiotemporal pressure distribution in the vaginal canal. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sweating under pressure: skin conductance level reactivity moderates the association between peer victimization and externalizing behavior.

Science.gov (United States)

Gregson, Kim D; Tu, Kelly M; Erath, Stephen A

2014-01-01

This study examined whether the association between peer victimization and externalizing behavior may be illuminated by individual differences in skin conductance level reactivity (SCLR) in the context of peer stress. Participants included 123 fifth and sixth graders (Mean age = 12.03 years, 50% females; 42% ethnic minorities). SCLR was assessed in the context of an ecologically relevant, lab-based peer-evaluative stress experience in preadolescence. As hypothesized, self-reported peer victimization was linked with parent- and teacher-reported externalizing behavior, and SCLR consistently moderated these associations. Peer victimization was associated with parent- and teacher-reported externalizing behavior among preadolescents who exhibited lower SCLR, but not among preadolescents who exhibited higher SCLR. Results suggest that promoting engagement with peer stress experiences and enhancing inhibitory control are potential intervention targets that may reduce externalizing behavior in the context of peer victimization (or reduce peer victimization among preadolescents who exhibit externalizing behavior). © 2013 The Authors. Journal of Child Psychology and Psychiatry © 2013 Association for Child and Adolescent Mental Health.

EVALUATION ON THE SEISMIC RESPONSE CHARACTERISTICS OF A ROAD EMBANKMENT BASED ON THE MODERATE EARTHQUAKE OBSERVATION AND THE MICROTREMOR MEASUREMENT

Science.gov (United States)

Hata, Yoshiya; Ichii, Koji; Yamada, Masayuki; Tokida, Ken-Ichi; Takezawa, Koichiro; Shibao, Susumu; Mitsushita, Junji; Murata, Akira; Furukawa, Aiko; Koizumi, Keigo

Accurate evaluation on the seismic response characteristics of a road embankment is very important for the rational seismic assessment. However, in a lot of previous studies, the seismic response characteristics of an embankment were evaluated based on the results of shaking table test, centrifuge model test and dynamic FEM analysis. In this study, the transfer function and the shear wave velocity of a road embankment were evaluated based on the in-situ records of moderate earthquake observation and microtremor measurement. Test results show the possibility that the shear wave velocity of an embankment can be estimated by the earthquake observation or the microtremor measurement and the dynamic linear FEM analysis.

Evaluation of containment peak pressure and structural response for a large-break loss-of-coolant accident in a VVER-440/213 NPP

Energy Technology Data Exchange (ETDEWEB)

Spencer, B.W.; Sienicki, J.J.; Kulak, R.F.; Pfeiffer, P.A. [Argonne National Lab., IL (United States); Voeroess, L.; Techy, Z. [VEIKI Inst. for Electric Power Research, Budapest (Hungary); Katona, T. [Paks Nuclear Power Plant (Hungary)

1998-07-01

A collaborative effort between US and Hungarian specialists was undertaken to investigate the response of a VVER-440/213-type NPP to a maximum design-basis accident, defined as a guillotine rupture with double-ended flow from the largest pipe (500 mm) in the reactor coolant system. Analyses were performed to evaluate the magnitude of the peak containment pressure and temperature for this event; additional analyses were performed to evaluate the ultimate strength capability of the containment. Separate cases were evaluated assuming 100% effectiveness of the bubbler-condenser pressure suppression system as well as zero effectiveness. The pipe break energy release conditions were evaluated from three sources: (1) FSAR release rate based on Soviet safety calculations, (2) RETRAN-03 analysis and (3) ATHLET analysis. The findings indicated that for 100% bubbler-condenser effectiveness the peak containment pressures were less than the containment design pressure of 0.25 MPa. For the BDBA case of zero effectiveness of the bubbler-condenser system, the peak pressures were less than the calculated containment failure pressure of 0.40 MPa absolute.

Temperature and pressure dependent osmotic pressure in liquid sodium-cesium alloys

International Nuclear Information System (INIS)

Rashid, R.I.M.A.

1987-01-01

The evaluation of the osmotic pressure in terms of the concentration fluctuations of mixtures and the equations of state of the pure liquids is considered. The temperature and pressure dependent experimentally measured concentration-concentration correlations in the long wavelength limit of liquid sodium-cesium alloys are used to demonstrate the appreciable dependence of the temperature and pressure on the osmotic pressure as a function of concentration. Introducing interchange energies as functions of temperature and pressure, our analysis is consistent with the Flory model. Thus, a formalism for evaluating the state dependent osmotic pressure is developed and our numerical work is considered to be an extension of the calculations of Rashid and March in the sense that a temperature and pressure dependent interchange energy parameter that more closely parameterizes the state dependent concentration fluctuations in the liquid alloys, is used. (author)

STUDY OF WATER HAMMERS IN THE FILLING OF THE SYSTEM OF PRESSURE COMPENSATION IN THE WATER-COOLED AND WATER-MODERATED POWER REACTORS

Directory of Open Access Journals (Sweden)

A. V. Korolyev

2017-01-01

Full Text Available The research presented in the article conforms to the severe accident that took place at the Three Mail Island nuclear power plant in the USA. The research is focused on improving the reliability of the pressure compensator that is an important equipment of the primary circuit. In order to simulate such a situation, the stand has been developed to simulate the design of the pressurizer of the PWR-440 reactor, in particular an elliptical shape of the upper lid which has a steam outlet pipe at the top of the construction that creates conditions for occurrence of such water hammers. For the experiments, an installation has been created that makes it possible to measure and record the water hammering that occur when the tanks are filled. Measurement of the amplitude of the water hammering was carried out by a specially developed piezoelectric sensor, and the registration – by a light-beam oscilloscope. The technique of carrying out the experiment is described and the results of an experimental study of the water hammers arising when the vessels are completely filled are presented. Quantitative data were obtained on the amplitudes of the hydraulic impacts depending on the rate of filling of the vessel and the diameter of the outlet, the maximum pressure of the hydraulic shock was 7–9 atm. Comparison of calculated and experimental data has been performed. The allowable discrepancy is explained by the calculated value of the system stiffness coefficient, which did not take into account the presence of welded seams in the tank that imparts the system with additional rigidity. The calculated relationships are obtained, that make it possible to estimate the amplitudes of the water hammers through the acceleration of the water level in front of the outlet from a vessel with an elliptical bottom. The possibility of a water hammer in the pressure compensator is demonstrated by experiment and by theoretical calculations. Based on the experimental data, a

Evaluation of Blood Pressure Control Levels and Treatment Compliances of Hypertensive Patients

Directory of Open Access Journals (Sweden)

Cenk Aypak

2013-04-01

Full Text Available Purpose: The aim of the study is to evaluate the knowledge of patients about hypertension (HT, compliance with lifestyle changes and to determine their blood pressure levels under antihypertensive therapy. Method: Hypertensive patients that applied to Family medicine outpatient clinics of Diskapi Yildirim Beyazit Education and Research Hospital for the first time, in 2012 (between February 1 to April 30, were included in our cross-sectional study. Patients are evaluated primarily for the control and the factors that can affect high blood pressure and the rate on achieving treatment goals. Results: Three hundred and forty patients were included in the study. The mean age of the patients was 60.5±10.7 years and 222 of them (65.3% were female. The blood pressure was not under control in 108 (31.8% patients. The mean body weight of male patients was statistically higher than females (p=0.015. The number of the patients that knew the normal blood pressure value was 249 (73.2%. Among those 155 (62.2% were women and 179 (71.9% were younger than 65 years of age (p=0.0001. Forty one patients (12.1% were still smoking, 46 (13.5% patients were exercising regularly and 32 (9.4% were consuming regular diet. Blood pressure was better controlled in the group that was exercising regularly (p=0.001. The rate of male patients that were on regular exercise and diet, were higher than females (p=0.09. Only 86 patients (25.3% knew the name of their antihypertensive medication and 65 of patients (19.1% knew the dose of their medication. Female patients knew the name of their medication better than males (p=0.002. 156 patients (45.9% were using two kinds of antihypertensive medication. 58 patients (17.1% were skipping doses a few times a week. Conclusion: The knowledge of hypertensive patients on their illness and their compliance on non-drug treatments were inadequate. The compliance of patients should be improved by development of patient-doctor should be improved

3-D CFD analysis of the CANDU-6 moderator circulation under normal operating conditions

International Nuclear Information System (INIS)

Yoon, Churl; Rhee, Bo Wook; Min, Byung Joo

2004-01-01

A computational fluid dynamics model for predicting moderator circulation inside the Canada Deuterium Uranium (CANDU) reactor vessel has been developed to estimate the local subcooling of the moderator in the vicinity of the calandria tubes. The buoyancy effect induced by the internal heating is accounted for by the Boussinesq approximation. The standard k-ε turbulence model with logarithmic wall treatment is applied to predict the turbulent jet flows from the inlet nozzles. The matrix of the calandria tubes in the core region is simplified to a porous media in which the anisotropic hydraulic impedance is modeled using an empirical correlation of pressure loss. The governing equations are solved by CFX-4.4, a commercial CFD code developed by AEA technology. The resultant flow patterns of the constant-z slices containing the inlet nozzles and the outlet port are 'mixed-type', as observed in the former 2-dimensional experimental investigations. With 103% full power for conservatism, the maximum temperature of the moderator is 82.9 deg. C at the top of the core region. Considering the hydrostatic pressure change, the minimum subcooling is 24.8 .deg. C

Cerebrospinal fluid pressures resulting from experimental traumatic spinal cord injuries in a pig model.

Science.gov (United States)

Jones, Claire F; Lee, Jae H T; Burstyn, Uri; Okon, Elena B; Kwon, Brian K; Cripton, Peter A

2013-10-01

Despite considerable effort over the last four decades, research has failed to translate into consistently effective treatment options for spinal cord injury (SCI). This is partly attributed to differences between the injury response of humans and rodent models. Some of this difference could be because the cerebrospinal fluid (CSF) layer of the human spine is relatively large, while that of the rodents is extremely thin. We sought to characterize the fluid impulse induced in the CSF by experimental SCIs of moderate and high human-like severity, and to compare this with previous studies in which fluid impulse has been associated with neural tissue injury. We used a new in vivo pig model (n = 6 per injury group, mean age 124.5 days, 20.9 kg) incorporating four miniature pressure transducers that were implanted in pairs in the subarachnoid space, cranial, and caudal to the injury at 30 mm and 100 mm. Tissue sparing was assessed with Eriochrome Cyanine and Neutral Red staining. The median peak pressures near the injury were 522.5 and 868.8 mmHg (range 96.7-1430.0) and far from the injury were 7.6 and 36.3 mmHg (range 3.8-83.7), for the moderate and high injury severities, respectively. Pressure impulse (mmHg.ms), apparent wave speed, and apparent attenuation factor were also evaluated. The data indicates that the fluid pressure wave may be sufficient to affect the severity and extent of primary tissue damage close to the injury site. However, the CSF pressure was close to normal physiologic values at 100 mm from the injury. The high injury severity animals had less tissue sparing than the moderate injury severity animals; this difference was statistically significant only within 1.6 mm of the epicenter. These results indicate that future research seeking to elucidate the mechanical origins of primary tissue damage in SCI should consider the effects of CSF. This pig model provides advantages for basic and preclinical SCI research due to its

Moderate Dilution of Copper Slag by Natural Gas

Science.gov (United States)

Zhang, Bao-jing; Zhang, Ting-an; Niu, Li-ping; Liu, Nan-song; Dou, Zhi-he; Li, Zhi-qiang

2018-01-01

To enable use of copper slag and extract the maximum value from the contained copper, an innovative method of reducing moderately diluted slag to smelt copper-containing antibacterial stainless steel is proposed. This work focused on moderate dilution of copper slag using natural gas. The thermodynamics of copper slag dilution and ternary phase diagrams of the slag system were calculated. The effects of blowing time, temperature, matte settling time, and calcium oxide addition were investigated. The optimum reaction conditions were identified to be blowing time of 20 min, reaction temperature of 1250°C, settling time of 60 min, CaO addition of 4% of mass of slag, natural gas flow rate of 80 mL/min, and outlet pressure of 0.1 MPa. Under these conditions, the Fe3O4 and copper contents of the residue were 7.36% and 0.50%, respectively.

Premoderator optimization of decoupled hydrogen moderator

International Nuclear Information System (INIS)

Harada, Masahide; Teshigawara, Makoto; Kai, Tetsuya; Sakata, Hideaki; Watanabe, Noboru; Ikeda, Yujiro

2001-03-01

An optimization study on the premoderator, the reflector material choice and a length of the linear is carried out for the design of high performance decoupled hydrogen moderator. NMTC/JAM and MCNP-4C are used for the neutronics calculation. The result indicates that, assuming premoderator dimensions and decoupling energy is controlled, the decoupled hydrogen moderator with a premoderator can provide better pulse characteristics than that without the premoderator for a Be reflector. On the selection of the reflector material, it is clearly shown that Pb and Hg reflectors give merits in using the premoderator for higher intensity and reduction of energy deposition in moderator. It is also shown that a H 2 O premoderator provides a short tail while a D 2 O premoderator provides the high peak intensity. Minimum liner length is evaluated to be 20 cm from the viewpoint of neutronics. (author)

Comprehensive evaluation of immunomodulation by moderate hypoxia in S. agalactiae vaccinated Nile tilapia.

Science.gov (United States)

Gallage, Sanchala; Katagiri, Takayuki; Endo, Masato; Maita, Masashi

2017-07-01

Streptococcus agalactiae is a major bacterial pathogen in tilapia aquaculture. Vaccines are known to provide protection but S. agalactiae clearance in tilapia can be reduced by marginal environmental conditions. Therefore, the purpose of this study is to examine S. agalactiae clearance in vaccinated Nile tilapia under moderate hypoxic (55± 5% DO) and normoxic (85 ± 5%DO) conditions. Fish were acclimatized to either moderate hypoxia or normoxia and immunized with formalin-inactivated S. agalactiae. Fish were experimentally challenged with S. agalactiae at 30 days post-vaccination. Serum antibody titer was significantly higher in vaccinated fish kept under normoxic condition compared to the moderate hypoxic condition at fifteen and thirty days post-vaccination. The cumulative mortality following challenge was significantly reduced in vaccinated fish kept under normoxic condition compared to those in moderate hypoxic condition reflecting that pre-challenge antibody titer may correlate with survival of fish. Blood and tissue pathogen burden detection of S. agalactiae studies revealed that culturable S. agalactiae cells could not be detected in the blood of normoxic vaccinated fish at all the sampling points. In contrast, fish vaccinated in moderate hypoxic condition had considerable number of culturable S. agalactiae cells in their blood up to 5 days following challenge. Phagocytosis and intracellular reactive oxygen species (ROS) production were lowered by moderate hypoxia in vitro. Furthermore, presence of specific antibodies and higher specific antibody level in the serum increased phagocytosis, ROS production and lowered intracellular survival of S. agalactiae in head kidney leukocytes. Overall this study has highlighted that S. agalactiae clearance in vaccinated Nile tilapia is modulated by moderate hypoxia. One of the possible explanations for this might be less efficient phagocytic activities due to low oxygen availability and lower specific

Radiographic evaluation of corrosion/erosion failures in pressure vessels and pipings in fertilizer industry

International Nuclear Information System (INIS)

Sinha, G.S.; Sahay, K.N.; Sundaram, K.V.; Banerji, K.C.

1977-01-01

The uses of radiography in combating the corrosion/erosion failures of pressure equipments used in the fertilizer industry are highlighted. Premature failures in fertilizer plants have proved to be very costly. One of the principal agencies responsible for such failures in process industry is corrosion/erosion. Radiography, when supplemented with other NDT-techniques, has been found to be ideal and highly useful method for on-stream inspection and evaluation of corrosion/erosion failures of pressure vessels and pipings. Three case-histories have been presented to illustrate the importance of radiography. (author)

Consequence evaluation of radiation embrittlement of Trojan reactor pressure vessel supports

International Nuclear Information System (INIS)

Lu, S.C.; Sommer, S.C.; Johnson, G.L.; Lambert, H.E.

1990-10-01

This report describes a consequence evaluation to address safety concerns raised by the radiation embrittlement of the reactor pressure vessel (RPV) supports for the Trojan nuclear power plant. The study comprises a structural evaluation and an effects evaluation and assumes that all four reactor vessel supports have completely lost the load carrying capability. By demonstrating that the ASME code requirements governing Level D service limits are satisfied, the structural evaluation concludes that the Trojan reactor coolant loop (RCL) piping is capable of transferring loads to the steam generator (SG) supports and the reactor coolant pump (RCP) supports. A subsequent design margins to accommodate additional loads transferred to them through the RCL piping. The effects evaluation, employing a systems analysis approach, investigates initiating events and the reliability of the engineered safeguard systems as the RPV is subject to movements caused by the RPV support failure. The evaluation identifies a number of areas of additional safety concerns, but further investigation of the above safety concerns, however, concludes that a hypothetical failure of the Trojan RPV supports due to radiation embrittlement will not result in consequences of significant safety concerns

Deep breathing exercises with positive expiratory pressure in patients with multiple sclerosis - a randomized controlled trial.

Science.gov (United States)

Westerdahl, Elisabeth; Wittrin, Anna; Kånåhols, Margareta; Gunnarsson, Martin; Nilsagård, Ylva

2016-11-01

Breathing exercises with positive expiratory pressure are often recommended to patients with advanced neurological deficits, but the potential benefit in multiple sclerosis (MS) patients with mild and moderate symptoms has not yet been investigated in randomized controlled trials. To study the effects of 2 months of home-based breathing exercises for patients with mild to moderate MS on respiratory muscle strength, lung function, and subjective breathing and health status outcomes. Forty-eight patients with MS according to the revised McDonald criteria were enrolled in a randomized controlled trial. Patients performing breathing exercises (n = 23) were compared with a control group (n = 25) performing no breathing exercises. The breathing exercises were performed with a positive expiratory pressure device (10-15 cmH 2 O) and consisted of 30 slow deep breaths performed twice a day for 2 months. Respiratory muscle strength (maximal inspiratory and expiratory pressure at the mouth), spirometry, oxygenation, thoracic excursion, subjective perceptions of breathing and self-reported health status were evaluated before and after the intervention period. Following the intervention, there was a significant difference between the breathing group and the control group regarding the relative change in lung function, favoring the breathing group (vital capacity: P < 0.043; forced vital capacity: P < 0.025). There were no other significant differences between the groups. Breathing exercises may be beneficial in patients with mild to moderate stages of MS. However, the clinical significance needs to be clarified, and it remains to be seen whether a sustainable effect in delaying the development of respiratory dysfunction in MS can be obtained. © 2015 The Authors. The Clinical Respiratory Journal published by John Wiley & Sons Ltd.

Moderate Contrast in the Evaluation of Paintings Is Liked More but Remembered Less than High Contrast

Directory of Open Access Journals (Sweden)

Katinka Dijkstra

2017-09-01

Full Text Available Many visual aspects of paintings, as well as exposure to art and cultural norms, contribute to the aesthetic evaluation of paintings. The current study looked at heightened visual contrast as an important factor in the appreciation of paintings. Participants evaluated abstract digitized paintings that were manipulated in contrast for an appreciation task and were later presented with these paintings in a memory task. The results indicated that for art appreciation, a moderate increase in contrast resulted in the highest appreciation for paintings whereas recognition memory was better for paintings with a higher increase in contrast. These results replicate earlier findings with regard to the role of contrast in aesthetic perception and extend these findings by demonstrating a surprising different effect of contrast manipulation for recognition memory. Confidence with which memory decisions were made was in line with art appreciation decisions not memory performance.

Safety and effectiveness of moderate sedation for radiologic non-vascular intervention

International Nuclear Information System (INIS)

Kim, Tae-Hoon

2006-01-01

The purpose of this study was to prospectively characterize the safety and effectiveness of moderate sedation/analgesia for performing radiologic non-vascular abdominal intervention. During a 3-month period, a total of 63 adult patients with a mean age of 64 years (range:27-82) underwent moderate sedation for 72 radiologic non-vascular interventional procedures. A combination of fentanyl citrate and midazolam hydrochloride, based on the patient's body weight, was intravenously administered until the patient was drowsy and tranquil. The adverse events associated with this moderate sedation were assessed. The visual analog scale format was used to measure the subjective feelings of the patient's pre-pro- cedural anxiety and intraprocedural pain. The mean total dose per kilogram of body weight of fentanyl used in PTBD was 1.148 μg. The mean total dose per kilogram of body weight of midazolam was 0.035 mg in PTBD, PTGBD, AD, PCN, DJS, GS and FRA, 0.039 mg in TDC, and 0.043 mg in BS. A temporary reduction of systolic blood pressure to less than 80 mmHg was observed during 5 procedures (6.9%), whereas a temporary elevation of systolic blood pressure above 150 mmHg was observed during 10 procedures (13.8%). A reduction of arterial oxygen saturation to less than 90% was observed during 14 procedures (19.4%). None of the patients required pharmacologic reversal agents or cardiopulmonary resuscitation. The mean anxiety score recorded before all procedures was 5.2 (distressing). The mean pain score during the procedure, which was recorded after all procedures, was 2.9 (mild). Moderate sedation allows performance of safe and effective radiologic non-vascular intervention, and it is also easy for an interventional radiologist to use. The patients should be continuously monitored to check their vital signs and arterial oxygen saturation during the procedures

Safety and effectiveness of moderate sedation for radiologic non-vascular intervention

Energy Technology Data Exchange (ETDEWEB)

Kim, Tae-Hoon [Dankook University Hospital, Chungju (Korea, Republic of)

2006-06-15

The purpose of this study was to prospectively characterize the safety and effectiveness of moderate sedation/analgesia for performing radiologic non-vascular abdominal intervention. During a 3-month period, a total of 63 adult patients with a mean age of 64 years (range:27-82) underwent moderate sedation for 72 radiologic non-vascular interventional procedures. A combination of fentanyl citrate and midazolam hydrochloride, based on the patient's body weight, was intravenously administered until the patient was drowsy and tranquil. The adverse events associated with this moderate sedation were assessed. The visual analog scale format was used to measure the subjective feelings of the patient's pre-pro- cedural anxiety and intraprocedural pain. The mean total dose per kilogram of body weight of fentanyl used in PTBD was 1.148 {mu}g. The mean total dose per kilogram of body weight of midazolam was 0.035 mg in PTBD, PTGBD, AD, PCN, DJS, GS and FRA, 0.039 mg in TDC, and 0.043 mg in BS. A temporary reduction of systolic blood pressure to less than 80 mmHg was observed during 5 procedures (6.9%), whereas a temporary elevation of systolic blood pressure above 150 mmHg was observed during 10 procedures (13.8%). A reduction of arterial oxygen saturation to less than 90% was observed during 14 procedures (19.4%). None of the patients required pharmacologic reversal agents or cardiopulmonary resuscitation. The mean anxiety score recorded before all procedures was 5.2 (distressing). The mean pain score during the procedure, which was recorded after all procedures, was 2.9 (mild). Moderate sedation allows performance of safe and effective radiologic non-vascular intervention, and it is also easy for an interventional radiologist to use. The patients should be continuously monitored to check their vital signs and arterial oxygen saturation during the procedures.

Relationship among vaginal palpation, vaginal squeeze pressure, electromyographic and ultrasonographic variables of female pelvic floor muscles

Directory of Open Access Journals (Sweden)

Vanessa S. Pereira

2014-10-01

Full Text Available Background: The proper evaluation of the pelvic floor muscles (PFM is essential for choosing the correct treatment. Currently, there is no gold standard for the assessment of female PFM function. Objective: To determine the correlation between vaginal palpation, vaginal squeeze pressure, and electromyographic and ultrasonographic variables of the female PFM. Method: This cross-sectional study evaluated 80 women between 18 and 35 years of age who were nulliparous and had no pelvic floor dysfunction. PFM function was assessed based on digital palpation, vaginal squeeze pressure, electromyographic activity, bilateral diameter of the bulbocavernosus muscles and the amount of bladder neck movement during voluntary PFM contraction using transperineal bi-dimensional ultrasound. The Pearson correlation was used for statistical analysis (p<0.05. Results: There was a strong positive correlation between PFM function and PFM contraction pressure (0.90. In addition, there was a moderate positive correlation between these two variables and PFM electromyographic activity (0.59 and 0.63, respectively and movement of the bladder neck in relation to the pubic symphysis (0.51 and 0.60, respectively. Conclusions: This study showed that there was a correlation between vaginal palpation, vaginal squeeze pressure, and electromyographic and ultrasonographic variables of the PFM in nulliparous women. The strong correlation between digital palpation and PFM contraction pressure indicated that perineometry could easily be replaced by PFM digital palpation in the absence of equipment.

Is Familiarity a Moderator of Brand/Country Alliances? One More Look

OpenAIRE

Tore Kristensen; Gorm Gabrielsen; Eugene D. Jaffe

2014-01-01

Product and brand familiarity have an important role in consumer choice behaviour and they have been equated with knowledge and experience Consumers having high and low familiarity utilized brand information (an extrinsic cue) in their evaluations, whereas moderately familiar consumers used intrinsic cues (product attributes) in evaluating products. The question of whether familiarity moderates the country-of-origin (COO) effect is a valid one. In this present paper, we attempt to provide add...

Moderate alcohol consumption and cognitive risk

Directory of Open Access Journals (Sweden)

Neafsey EJ

2011-08-01

Full Text Available Edward J Neafsey, Michael A CollinsDepartment of Molecular Pharmacology and Therapeutics, Loyola University Chicago, Stritch School of Medicine, Maywood, IL, USAAbstract: We reviewed 143 papers that described the relationship between moderate drinking of alcohol and some aspect of cognition. Two types of papers were found: (1 those that provided ratios of risk between drinkers and nondrinkers (74 papers in total and (2 those that, although they did not provide such ratios, allowed cognition in drinkers to be rated as “better,” “no different,” or “worse” than cognition in nondrinkers (69 papers in total. The history of research on moderate drinking and cognition can be divided into two eras: 1977–1997 and 1998–present. Phase I (1977–1997 was the era of neuropsychological evaluation involving mostly young to middle-aged (18–50 years old subjects. Although initial studies indicated moderate drinking impaired cognition, many later studies failed to confirm this, instead finding no difference in cognition between drinkers and nondrinkers. Phase II (1998–present was and is the era of mental status exam evaluation involving mostly older (≥55 years old subjects. These studies overwhelmingly found that moderate drinking either reduced or had no effect on the risk of dementia or cognitive impairment. When all the ratios of risk from all the studies in phase II providing such ratios are entered into a comprehensive meta-analysis, the average ratio of risk for cognitive risk (dementia or cognitive impairment/decline associated with moderate “social” (not alcoholic drinking of alcohol is 0.77, with nondrinkers as the reference group. The benefit of moderate drinking applied to all forms of dementia (dementia unspecified, Alzheimer’s disease, and vascular dementia and to cognitive impairment (low test scores, but no significant benefit against cognitive decline (rate of decline in test scores was found. Both light and moderate

The first Iranian recommendations on prevention, evaluation and management of high blood pressure.

Science.gov (United States)

Noohi, Feridoun; Sarrafzadegan, Nizal; Khosravi, Alireza; Andalib, Elham

2012-01-01

This paper presents the complete report of the first Iranian Recommendations on Prevention, Evaluation and Management of High Blood Pressure. The purpose is to provide an evidence-based approach to the prevention, management and control of hypertension (HTN) by adapting the most internationally known and used guidelines to the local health care status with consideration of the currently available data and based on the locally conducted researches on HTN as well as social and health care requirements. A working group of national and international experts participated in discussions and collaborated in decision-making, writing and reviewing the whole report. Multiple subcommittees worked together to review the recent national and international literature on HTN in different areas. We used the evaluation tool that is called "AGREE" and considered a score of > 60% as a high score. We adapted the Canadian Hypertension Education Program (CHEP), the United Kingdom's National Institute for Health and Clinical Excellence (NICE) and the US-based joint National Committee on Prevention, Detection, Evaluation and Treatment of High Blood Pressure (JNC7). The key topics that are highlighted in this report include: The importance of ambulatory and self-measurement of blood pressure, evaluation of cardiovascular risk in HTN patients, the role of lifestyle modification in the prevention of HTN and its control with more emphasis on salt intake reduction and weight control, introducing pharmacotherapy suitable for uncomplicated HTN or specific situations and the available drugs in Iran, highlighting the importance of angiotensin-converting enzyme inhibitors, angiotensin-receptor blockers and calcium channel blockers as the first line therapy in many situations, the non-use of beta blockers as the first time treatment except in specific conditions, treating HTN in women, children, obese and elderly patients, the patient compliance to improve HTN control, practical guidelines to improve

Technical Evaluation Report 54: Best practices in synchronous conferencing moderation

Directory of Open Access Journals (Sweden)

Lynn Anderson, Barb Fyvie, Brenda Koritko, Kathy McCarthy, Sonia Murillo Paz, Mary Rizzuto, Remi Tremblay, and Urel Sawyers

2006-06-01

Full Text Available Practical guidelines are offered for the use of online synchronous conferencing software by session administrators and moderators. The configuration of the software prior to conferencing sessions is discussed, and the planning and implementation of useful collaborative activities such as “synchronised browsing.” The combination of these practices into useful ”patterns” for specific online conferencing purposes is discussed.

Conceptual mechanical design for a pressure-tube type supercritical water-cooled reactor

Energy Technology Data Exchange (ETDEWEB)

Yetisir, M.; Diamond, W.; Leung, L.K.H.; Martin, D.; Duffey, R. [Atomic Energy of Canada Limited, Chalk River, ON (Canada)

2011-07-01

This paper presents a conceptual mechanical design for a heavy-water-moderated pressure-tube supercritical water (SCW) reactor, which has evolved from the well-established CANDU nuclear reactor. As in the current designs, the pressure-tube SCW reactor uses a calandria vessel and, as a result, many of today's technologies (such as the shutdown safety systems) can readily be adopted with small changes. Because the proposed concept uses a low-pressure moderator, it does not require a pressure vessel that is subject to the full SCW pressure and temperature conditions. The proposed design uses batch refueling and hence, the reactor core is orientated vertically. Significant simplifications result in the design with the elimination of on line fuelling systems, fuel channel end fittings and fuel channel closure seals and thus utilize the best features of Light Water Reactor (LWR) and Heavy Water Reactor (HWR) technologies. The safety goal is based on achieving a passive 'no core melt' configuration for the channels and core, so the mechanical features and systems directly reflect this desired attribute. (author)

Conceptual mechanical design for a pressure-tube type supercritical water-cooled reactor

International Nuclear Information System (INIS)

Yetisir, M.; Diamond, W.; Leung, L.K.H.; Martin, D.; Duffey, R.

2011-01-01

This paper presents a conceptual mechanical design for a heavy-water-moderated pressure-tube supercritical water (SCW) reactor, which has evolved from the well-established CANDU nuclear reactor. As in the current designs, the pressure-tube SCW reactor uses a calandria vessel and, as a result, many of today's technologies (such as the shutdown safety systems) can readily be adopted with small changes. Because the proposed concept uses a low-pressure moderator, it does not require a pressure vessel that is subject to the full SCW pressure and temperature conditions. The proposed design uses batch refueling and hence, the reactor core is orientated vertically. Significant simplifications result in the design with the elimination of on line fuelling systems, fuel channel end fittings and fuel channel closure seals and thus utilize the best features of Light Water Reactor (LWR) and Heavy Water Reactor (HWR) technologies. The safety goal is based on achieving a passive 'no core melt' configuration for the channels and core, so the mechanical features and systems directly reflect this desired attribute. (author)

Pressure slip casting and cold isostatic pressing of aluminum titanate green ceramics: A comparative evaluation

Directory of Open Access Journals (Sweden)

Ramanathan Papitha

2013-12-01

Full Text Available Aluminum titanate (Al2TiO5 green bodies were prepared from mixture of titania and alumina powders with different particle sizes by conventional slip casting (CSC, pressure slip casting (PSC and cold isostatic pressing (CIP. Precursor-powder mixtures were evaluated with respect to the powder properties, flow behaviours and shaping parameters. Green densities were measured and correlated with the fractographs. A substantial increase in green densities up to 60 %TD (theoretical density of 4.02 g/cm3, calculated based on rule of mixtures is observed with the application of 2–3 MPa pressure with PSC. While particle size distribution and solid loading are the most influential parameters in the case of CSC, with PSC pressure also plays a key role in achieving the higher green densities. Being a dry process, high pressure of > 100 MPa for CIP is essential to achieve densities in the range of 60–65 %TD. Slip pressurization under PSC conditions facilitate the rearrangement of particles through rolling, twisting and interlocking unlike CIP processing where pressure is needed to overcome the inter-particle friction.

Hazardous gas treatment using atmospheric pressure microwave discharges

International Nuclear Information System (INIS)

Mizeraczyk, Jerzy; Jasinski, Mariusz; Zakrzewski, Zenon

2005-01-01

Atmospheric pressure microwave discharge methods and devices used for producing non-thermal plasmas for control of gaseous pollutants are described in this paper. The main part of the paper is concerned with microwave torch discharges (MTDs). Results of laboratory experiments on plasma abatement of several volatile organic compounds (VOCs) in their mixtures with either synthetic air or nitrogen in low (∼100 W) and moderate (200-400 W) microwave torch plasmas at atmospheric pressure are presented. Three types of MTD generators, i.e. low-power coaxial-line-based MTDs, moderate-power waveguide-based coaxial-line MTDs and moderate-power waveguide-based MTDs were used. The gas flow rate and microwave (2.45 GHz) power delivered to the discharge were in the range of 1-3 litre min -1 and 100-400 W, respectively. The concentrations of the processed gaseous pollutants were from several to several tens of per cent. The results showed that the MTD plasmas fully decomposed the VOCs at a relatively low energy cost. The energy efficiency of decomposition of several gaseous pollutants reached 1000 g (kW-h) -1 . This suggests that MTD plasmas can be useful tools for decomposition of highly concentrated VOCs

Students' Scientific Epistemic Beliefs, Online Evaluative Standards, and Online Searching Strategies for Science Information: The Moderating Role of Cognitive Load Experience

Science.gov (United States)

Hsieh, Ya-Hui; Tsai, Chin-Chung

2014-01-01

The purpose of this study is to examine the moderating role of cognitive load experience between students' scientific epistemic beliefs and information commitments, which refer to online evaluative standards and online searching strategies. A total of 344 science-related major students participated in this study. Three questionnaires were…

Evaluation of the acute adverse reaction of contrast medium with high and moderate iodine concentration in patients undergoing computed tomography

International Nuclear Information System (INIS)

Nagamoto, Masashi; Gomi, Tatsuya; Terada, Hitoshi; Terada, Shigehiko; Kohda, Eiichi

2006-01-01

The aim of this prospective study was to evaluate and compare acute adverse reactions between contrast medium containing moderate and high concentrations of iodine in patients undergoing computed tomography (CT). A total of 945 patients undergoing enhanced CT were randomly assigned to receive one of two doses of contrast medium. We then prospectively investigated the incidence of adverse reactions. Iopamidol was used as the contrast medium, with a high concentration of 370 mgI/ml and a moderate concentration of 300 mgI/ml. The frequency of adverse reactions, such as pain at the injection site and heat sensation, were determined. Acute adverse reactions were observed in 2.4% (11/458) of the moderate-concentration group compared to 3.11% (15/482) of the high-concentration group; there was no significant difference in incidence between the two groups. Most adverse reactions were mild, and there was no significant difference in severity. One patient in the high-concentration group was seen to have a moderate adverse reaction. No correlation existed between the incidence of adverse reactions and patient characteristics such as sex, age, weight, flow amount, and flow rate. The incidence of pain was not significantly different between the two groups. In contrast, the incidence of heat sensation was significantly higher in the high-concentration group. The incidence and severity of acute adverse reactions were not significantly different between the two groups, and there were no severe adverse reactions in either group. (author)

Pressure tube reactors

International Nuclear Information System (INIS)

Natori, Hisahide.

1981-01-01

Purpose: To improve the electrical power generation efficiency in a pressure tube reactor in which coolants and moderators are separated by feedwater heating with heat generated in heavy water and by decreasing the amount of steams to be extracted from the turbine. Constitution: A heat exchanger and a heavy water cooler are additionally provided to a conventional pressure tube reactor. The heat exchanger is disposed at the pre-stage of a low pressure feedwater heater series. High temperature heavy water heated in the core is passed through the primary side of the exchanger, while feedwater is passed through the secondary side. The cooler is disposed on the downstream of the heat exchanger in the flowing direction of the heavy water, in which heavy water from the heat exchanger is passed through the primary side and the auxiliary equipment cooling water is sent to the secondary side thereof. Accordingly, since extraction of heating steams is no more necessary, the steam can be used for the rotation of the turbine, and the electrical power generation efficiency can be improved. (Seki, T.)

Optimal right heart filling pressure in acute respiratory distress syndrome determined by strain echocardiography.

Science.gov (United States)

Garcia-Montilla, Romel; Imam, Faryal; Miao, Mi; Stinson, Kathryn; Khan, Akram; Heitner, Stephen

2017-06-01

Right ventricular (RV) systolic dysfunction is common in acute respiratory distress syndrome (ARDS). While preload optimization is crucial in its management, dynamic fluid responsiveness indices lack reliability, and there is no consensus on target central venous pressure (CVP). We analyzed the utility of RV free wall longitudinal strain (RVFWS) in the estimation of optimal RV filling pressure in ARDS. A retrospective cross-sectional analysis of clinical data and echocardiograms of patients with ARDS was performed. Tricuspid annular plane systolic excursion (TAPSE), tricuspid peak systolic velocity (S'), RV fractional area change (RVFAC), RVFWS, CVP, systolic pulmonary artery pressure (SPAP), and left ventricular ejection fraction (LVEF) were measured. Fifty-one patients with moderate-severe ARDS were included. There were inverse correlations between CVP and TAPSE, S', RVFAC, RVFWS, and LVEF. The most significant was with RVFWS (r:.74, R 2 :.55, P:.00001). Direct correlations with creatinine and lactate were noted. Receiver operating characteristic analysis showed that RVFWS -21% (normal reference value) was associated with CVP: 13 mm Hg (AUC: 0.92, 95% CI: 0.83-1.00). Regression model analysis of CVP, and RVFWS interactions established an RVFWS range from -18% to -24%. RVFWS -24% corresponded to CVP: 11 mm Hg and RVFWS -18% to CVP: 15 mm Hg. Beyond a CVP of 15 mm Hg, biventricular systolic dysfunction rapidly ensues. Our data are the first to show that an RV filling pressure of 13±2 mm Hg-as by CVP-correlates with optimal RV mechanics as evaluated by strain echocardiography in patients with moderate-severe ARDS. © 2017, Wiley Periodicals, Inc.

Impacts on oil recovery from capillary pressure and capillary heterogeneities

Energy Technology Data Exchange (ETDEWEB)

Bognoe, Thomas

2008-07-01

The main conclusions drawn from this thesis are; 7 scientific papers are published on a broad variety of subjects, and describes in detail the experiments and research treated in this thesis. Scientific research has been performed, investigating the subjects of capillary pressure and capillary heterogeneities from different angles. This thesis discusses the findings in this study and aims to illustrate the benefits of the results obtained for further development of other experiments, and/or even the industrial benefits in field development. The methods for wettability alteration have developed throughout the work. From producing heterogeneous wettability alterations, the methods have improved to giving both radial and lateral uniform wettability alterations, which also remains unaltered throughout the duration of the experimental work. The alteration of wettability is dependent on initial water saturation, flow rate, aging time and crude oil composition. Capillary pressure and relative permeability curves have been measured for core plugs at different wettabilities using conventional centrifuge methods. The trends observed are mostly consistent with theory. The production mechanisms of strongly and moderately water wet chalk has been investigated. At strongly water wet conditions in fractured chalk; the flow is governed by capillary forces, showing strong impact from the fractures. At moderately water wet conditions, the impact of the fractures are absent, and a dispersed water front is observed during the displacement. The oil recovery is about the same, at the two wettabilities. Fracture crossing mechanisms at the same wettability conditions have been mapped. And the observations are consistent with those of the water floods. During strongly water wet displacement, the fracture crossing is occurring once the inlet core has reached endpoint of spontaneous imbibition. At moderately water wet conditions the fracture crossing is less abrupt, and creation of wetting

Report on the international workshop on cold moderators for pulsed neutron sources

International Nuclear Information System (INIS)

Carpenter, J. M.

1999-01-01

The International Workshop on Cold Moderators for Pulsed Neutron Sources resulted from the coincidence of two forces. Our sponsors in the Materials Sciences Branch of DOE's Office of Energy Research and the community of moderator and neutron facility developers both realized that it was time. The Neutron Sources Working Group of the Megascience Forum of the Organization for Economic Cooperation and Development offered to contribute its support by publishing the proceedings, which with DOE and Argonne sponsorship cemented the initiative. The purposes of the workshop were: to recall and improve the theoretical groundwork of time-dependent neutron thermalization; to pose and examine the needs for and benefits of cold moderators for neutron scattering and other applications of pulsed neutron sources; to summarize experience with pulsed source, cold moderators, their performance, effectiveness, successes, problems and solutions, and the needs for operational data; to compile and evaluate new ideas for cold moderator materials and geometries; to review methods of measuring and characterizing pulsed source cold moderator performance; to appraise methods of calculating needed source characteristics and to evaluate the needs and prospects for improvements; to assess the state of knowledge of data needed for calculating the neutronic and engineering performance of cold moderators; and to outline the needs for facilities for testing various aspects of pulsed source cold moderator performance

Report on the international workshop on cold moderators for pulsed neutron sources.

Energy Technology Data Exchange (ETDEWEB)

Carpenter, J. M.

1999-01-06

The International Workshop on Cold Moderators for Pulsed Neutron Sources resulted from the coincidence of two forces. Our sponsors in the Materials Sciences Branch of DOE's Office of Energy Research and the community of moderator and neutron facility developers both realized that it was time. The Neutron Sources Working Group of the Megascience Forum of the Organization for Economic Cooperation and Development offered to contribute its support by publishing the proceedings, which with DOE and Argonne sponsorship cemented the initiative. The purposes of the workshop were: to recall and improve the theoretical groundwork of time-dependent neutron thermalization; to pose and examine the needs for and benefits of cold moderators for neutron scattering and other applications of pulsed neutron sources; to summarize experience with pulsed source, cold moderators, their performance, effectiveness, successes, problems and solutions, and the needs for operational data; to compile and evaluate new ideas for cold moderator materials and geometries; to review methods of measuring and characterizing pulsed source cold moderator performance; to appraise methods of calculating needed source characteristics and to evaluate the needs and prospects for improvements; to assess the state of knowledge of data needed for calculating the neutronic and engineering performance of cold moderators; and to outline the needs for facilities for testing various aspects of pulsed source cold moderator performance.

Development work for the moderator of the ITR-fuel

International Nuclear Information System (INIS)

Duenner, P.; Becker, D.

1973-06-01

In the frame of the ITR-project (Incore-Thermionic-Reactor) fuel-moderator-materials had been investigated, which are also of interest for the KNK-project and which are therefore documented in this report. Partial pressure measurements on the systems Zr-H, Zr U-H, Y-H and YH-H revealed the premise for the elaboration of a hydration technique. On the basis of the functional relation between partial H 2 -pressure, temperature and H 2 -content of the hydride, an optimum hydration kinetic for the production of flawless and well defined hydrated Zirconium hydride/Uranium pellets and of Zirconium hydride and Yttrium hydride moderator bodies was developed. Alternatively to the ZrH x -U-technology a powder- metallurgical procedure for the production of a Y-U sinter-alloy as base material was tested. In an irradiation experiment in the DIDO reactor (in Juelich) the burnup behavior of Zirconium hydride-Uranium and Yttrium hydride-Uranium under ITR-similar conditions has been tested. With a U235-burnup of 6.75 % and an irradiation temperature of 490 deg C a fission gas release rate of 0.1 % was observed. The ZrH x -pellets remained mechanically intact, whereas the YH x -pellets crumbled during the post-examinations. The ZrH x -U showed a maximum density reduction of 4.2 % [de

Prevalence of renal artery stenosis in subjects with moderate hypertension. A population-based study

DEFF Research Database (Denmark)

Andersen, Ulrik B; Borglykke, Anders; Jørgensen, Torben

2011-01-01

Abstract Aim. To examine the prevalence of significant renal artery stenosis (RAS) in subjects with moderate to severe hypertension. Materials and methods. Subjects aged 50-66 years with blood pressure >160/100 mmHg or receiving antihypertensive treatment were selected from the population study...

Design, fabrication and metrological evaluation of wearable pressure sensors.

Science.gov (United States)

Goy, C B; Menichetti, V; Yanicelli, L M; Lucero, J B; López, M A Gómez; Parodi, N F; Herrera, M C

2015-04-01

Pressure sensors are valuable transducers that are necessary in a huge number of medical application. However, the state of the art of compact and lightweight pressure sensors with the capability of measuring the contact pressure between two surfaces (contact pressure sensors) is very poor. In this work, several types of wearable contact pressure sensors are fabricated using different conductive textile materials and piezo-resistive films. The fabricated sensors differ in size, the textile conductor used and/or the number of layers of the sandwiched piezo-resistive film. The intention is to study, through the obtaining of their calibration curves, their metrological properties (repeatability, sensitivity and range) and determine which physical characteristics improve their ability for measuring contact pressures. It has been found that it is possible to obtain wearable contact pressure sensors through the proposed fabrication process with satisfactory repeatability, range and sensitivity; and that some of these properties can be improved by the physical characteristics of the sensors.

Ultrasound Evaluation of Patients with Moderate and Severe Carpal Tunnel Syndrome

Directory of Open Access Journals (Sweden)

Ali Moghtaderi

2012-01-01

Full Text Available The objective of this study is to determine cut-off points for the crosssectional areas of the median nerve proximal and distal to carpal tunnel in moderate and severe Carpal Tunnel Syndrome (CTS and compare the results of our study with those available in the literature. Forty-three patients with upper limb pain other than CTS and 36 patients with idiopathic CTS enrolled into the study. The diagnosis and categorization of CTS were based on electrophysiologic criteria of the American Academy of Neurology. Median nerve cross-sectional areas were measured. Arithmetic mean values and standard deviation of each variable were measured. Student t-test and chi-squared test were applied to compare continuous and dichotomous variables between CTS and non-CTS control groups. Ultimately the diagnostic performances of the test characteristics including sensitivity, specificity, positive and negative predictive values were measured. Mean cross-sectional area of the nerve is higher in moderate than severe CTS proximal and distal to carpal tunnel. We accepted cut-off points of 11.5 mm2 and 13.5 mm2 for cross-sectional areas of the proximal and distal portions of carpal canal respectively. The sensitivity, specificity, positive and negative predictive values for the proximal inlet are 83%, 90.7%, 65.5% and 55.7%; and for the distal outlet are 36.1%, 93%, 81.2% and 63.4% respectively. We suggest that ultrasound is a good diagnostic modality for patients referred to tertiary care centers which categorized as moderate CTS.

Normal endothelial function in patients with mild-to-moderate psoriasis: a case-control study

DEFF Research Database (Denmark)

Jensen, Peter R; Zachariae, Claus; Hansen, Peter

2011-01-01

-dependent and technically demanding ultrasound measurement of brachial artery flow-mediated vasodilation. Therefore, we decided to measure endothelial function and other cardiovascular risk factors in patients with mild-to-moderate psoriasis (n = 30) and controls (n = 30) using a newer and relatively operator......Evidence is increasing that severe psoriasis is an independent cardiovascular risk factor. Results from case-control studies of endothelial dysfunction, a marker of early atherosclerosis, in patients with moderate-to-severe psoriasis have been conflicting and were conducted with operator...... blood pressures, and plasma levels of triglycerides, very-low-density lipoprotein cholesterol and glycated glucose, compared with controls. This indicates that even mild-to-moderate psoriasis may be regarded as a systemic inflammatory disease, and that an increased risk of cardiovascular morbidity may...

Report From BPTCS Project Team On Evaluation Of Additive Manufacturing For Pressure Retaining Equipment

Energy Technology Data Exchange (ETDEWEB)

Rawls, G. [Savannah River Site (SRS), Aiken, SC (United States)

2016-09-22

ASME is evaluating the use of additive manufacturing (AM) for the construction of pressure equipment. The information in this report assesses available AM technologies for direct metal fabrication of pressure equipment. Background information is included in the report to provide context for those not experienced in AM technology. Only commercially available technologies for direct metal fabrication are addressed in the report because these AM methods are the only viable approaches for the construction of pressure equipment. Metal AM technologies can produce near-net shape parts by using multiple layers of material from a three dimensional (3D) design model of the geometry. Additive manufacturing of metal components was developed from polymer based rapid prototyping or 3D printing. At the current maturity level, AM application for pressure equipment has the potential to reduce delivery times and costs for complex shapes. AM will also lead to a reduction in the use of high cost materials, since parts can be created with corrosion resistant layers of high alloy material and structural layers of lower cost materials.

Curvilinear Moderation—A More Complete Examination of Moderation Effects in Behavioral Sciences

OpenAIRE

Johnson Ching-Hong Li

2018-01-01

In behavioral sciences, researchers often examine whether any linear moderations exist in their studies. That is, they evaluate the extent (i.e., magnitude, direction) to which a linear effect of a predictor X (e.g., cognitive ability) on a criterion Y (e.g., performance) may differ across the levels of a moderator M (e.g., gender). In that case, researchers often run a liner regression analysis for examining this moderation (e.g., gender by ability). Despite its popularity, linear moderation...

High-temperature transient creep properties of CANDU pressure tubes

International Nuclear Information System (INIS)

Fong, R.W.L.; Chow, C.K.

2002-06-01

During a hypothetical large break loss-of-coolant accident (LOCA), the coolant flow would be reduced in some fuel channels and would stagnate and cause the fuel temperature to rise and overheat the pressure tube. The overheated pressure tube could balloon (creep radially) into contact with its moderator-cooled calandria tube. Upon contact, the stored thermal energy in the pressure tube is transferred to the calandria tube and into the moderator, which acts as a heat sink. For safety analyses, the modelling of fuel channel deformation behaviour during a large LOCA requires a sound knowledge of the high-temperature creep properties of Zr-2.5Nb pressure tubes. To this extent, a ballooning model to predict pressure-tube deformation was developed by Shewfelt et al., based on creep equations derived using uniaxial tensile specimens. It has been recognized, however, that there is an inherent variability in the high-temperature creep properties of CANDU pressure tubes. The variability, can be due to different tube-manufacturing practices, variations in chemical compositions, and changes in microstructure induced by irradiation during service in the reactor. It is important to quantify the variability of high-temperature creep properties so that accurate predictions on pressure-tube creep behaviour can be made. This paper summarizes recent data obtained from high-temperature uniaxial creep tests performed on specimens taken from both unirradiated (offcut) and irradiated pressure tubes, suggesting that the variability is attributed mainly to the initial differences in microstructure (grain size, shape and preferred orientation) and also from tube-to-tube variations in chemical composition, rather than due to irradiation exposure. These data will provide safety analysts with the means to quantify the uncertainties in the prediction of pressure-tube contact temperatures during a postulated large break LOCA. (author)

Feasibility and safety of low-flow extracorporeal carbon dioxide removal to facilitate ultra-protective ventilation in patients with moderate acute respiratory distress sindrome.

Science.gov (United States)

Fanelli, Vito; Ranieri, Marco V; Mancebo, Jordi; Moerer, Onnen; Quintel, Michael; Morley, Scott; Moran, Indalecio; Parrilla, Francisco; Costamagna, Andrea; Gaudiosi, Marco; Combes, Alain

2016-02-10

Mechanical ventilation with a tidal volume (VT) of 6 mL/kg/predicted body weight (PBW), to maintain plateau pressure (Pplat) lower than 30 cmH2O, does not completely avoid the risk of ventilator induced lung injury (VILI). The aim of this study was to evaluate safety and feasibility of a ventilation strategy consisting of very low VT combined with extracorporeal carbon dioxide removal (ECCO2R). In fifteen patients with moderate ARDS, VT was reduced from baseline to 4 mL/kg PBW while PEEP was increased to target a plateau pressure--(Pplat) between 23 and 25 cmH2O. Low-flow ECCO2R was initiated when respiratory acidosis developed (pH 60 mmHg). Ventilation parameters (VT, respiratory rate, PEEP), respiratory compliance (CRS), driving pressure (DeltaP = VT/CRS), arterial blood gases, and ECCO2R system operational characteristics were collected during the period of ultra-protective ventilation. Patients were weaned from ECCO2R when PaO2/FiO2 was higher than 200 and could tolerate conventional ventilation settings. Complications, mortality at day 28, need for prone positioning and extracorporeal membrane oxygenation, and data on weaning from both MV and ECCO2R were also collected. During the 2 h run in phase, VT reduction from baseline (6.2 mL/kg PBW) to approximately 4 mL/kg PBW caused respiratory acidosis (pH protective mechanical ventilation strategy in patients with moderate ARDS.

Licensing assessment of the Candu Pressurized Heavy Water Reactor. Preliminary safety information document. Volume II

International Nuclear Information System (INIS)

1977-06-01

ERDA has requested United Engineers and Constructors (UE and C) to evaluate the design of the Canadian natural uranium fueled, heavy water moderated (CANDU) nuclear reactor power plant to assess its conformance with the licensing criteria and guidelines of the U.S. Nuclear Regulatory Commission (USNRC) for light water reactors. This assessment was used to identify cost significant items of nonconformance and to provide a basis for developing a detailed cost estimate for a 1140 MWe, 3-loop Pressurized Heavy Water Reactor (PHWR) located at the Middletown, USA Site

Procurement of replacement pressure vessels for MURR

International Nuclear Information System (INIS)

Meyer, W.A. Jr.; Edwards, C.B. Jr.; McKibben, J.C.; Schoone, A.R.

1989-01-01

The University of Missouri Research Reactor Facility (MURR) located in Columbia, Missouri, is the highest powered, highest steady-state flux university research reactor in the United States. The reactor is a 10-MW pressurized loop, in-pool-type, light-water-moderated, beryllium-reflected, flux trap reactor. MURR has a compact core (0.033 m 3 ) composed of eight fuel elements of the materials test reactor type arranged as an annular right circular cylinder between the inner and outer aluminum pressure vessels. Conservative engineering judgment resulted in the decision in 1988 to purchase new inner and outer pressure vessels. This paper details the difficulties encountered in procuring replacements for aluminum pressure vessels built to standards that are no longer applicable in attempting to meet nuclear standards that are not applicable to nonferrous material

Therapy of moderate and severe psoriasis

Directory of Open Access Journals (Sweden)

Werfel, Thomas

2006-04-01

Full Text Available Objective and methods: This health technology assessment (HTA report synthesises systematically randomized controlled studies (RCT on the therapy of moderate and severe psoriasis vulgaris which were published between 1999 and 2004; it includes some important clinical studies which have been published after 2004 and thus updates the English HTA report by Griffiths et al. [1]. The major objective is the evaluation of the medical effectiveness of different therapeutical approaches and the cost effectiveness with relevance for Germany. Results: The major conclusions from the results of medical RCT on moderate and severe psoriasis vulgaris are: Oral fumarates are effective in the treatment of moderate to severe psoriasis vulgaris. However, fumarates quiet frequently cause moderate side effects. Cyclosporine and methotrexate are both effective in the treatment of severe psoriasis vulgaris. Both substances have a different spectrum of side effects which may limit the individual applicability. Acetritin is only moderately effective in the treatment of severe psoriasis of the plaque type. Calcipotriol or UV-radiation used at the same time can increase the clinical effectiveness of acetritin. Systemic PUVA, balneo-PUVA and UVB therapy are all effective for the treatment of severe psoriasis. The combination of UV therapy with vitamin D3 analogues or with topical steroids is more effective than the treatment with UV radiation alone. Saltwater baths increase the effectiveness of UVB therapy. No RCT on the therapeutical effects of topical tar or of dithranol in combination with UV therapy have been published so far. A continuous therapy with PUVA should not be applied due to its proven photocarcinogenicity. Three substances from the group of biologicals (Efalizumab, Etanercept, and Infliximab are now available in Europe and a further substance (Alefacept is available in the USA for the treatment of moderate to severe psoriasis. All biologicals have been

Roles of preoperative arterial blood gas tests in the surgical treatment of scoliosis with moderate or severe pulmonary dysfunction.

Science.gov (United States)

Liu, Jia-Ming; Shen, Jian-Xiong; Zhang, Jian-Guo; Zhao, Hong; Li, Shu-Gang; Zhao, Yu; Qiu, Giu-Xing

2012-01-01

It has been stated that preoperative pulmonary function tests are essential to assess the surgical risk in patients with scoliosis. Arterial blood gas tests have also been used to evaluate pulmonary function before scoliotic surgery. However, few studies have been reported. The aim of this study was to investigate the roles of preoperative arterial blood gas tests in the surgical treatment of scoliosis with moderate or severe pulmonary dysfunction. This study involved scoliotic patients with moderate or severe pulmonary dysfunction (forced vital capacity treatment between January 2002 and April 2010. A total of 73 scoliotic patients (23 males and 50 females) with moderate or severe pulmonary dysfunction were included. The average age of the patients was 16.53 years (ranged 10 - 44). The demographic distribution, medical records, and radiographs of all patients were collected. All patients received arterial blood gas tests and pulmonary function tests before surgery. The arterial blood gas tests included five parameters: partial pressure of arterial oxygen, partial pressure of arterial carbon dioxide, alveolar-arterial oxygen tension gradient, pH, and standard bases excess. The pulmonary function tests included three parameters: forced expiratory volume in 1 second ratio, forced vital capacity ratio, and peak expiratory flow ratio. All five parameters of the arterial blood gas tests were compared between the two groups with or without postoperative pulmonary complications by variance analysis. Similarly, all three parameters of the pulmonary function tests were compared. The average coronal Cobb angle before surgery was 97.42° (range, 50° - 180°). A total of 15 (20.5%) patients had postoperative pulmonary complications, including hypoxemia in 5 cases (33.3%), increased requirement for postoperative ventilatory support in 4 (26.7%), pneumonia in 2 (13.3%), atelectasis in 2 (13.3%), pneumothorax in 1 (6.7%), and hydrothorax in 1 (6.7%). No significant differences

Longitudinal assessment of high blood pressure in children with nonalcoholic fatty liver disease.

Science.gov (United States)

Schwimmer, Jeffrey B; Zepeda, Anne; Newton, Kimberly P; Xanthakos, Stavra A; Behling, Cynthia; Hallinan, Erin K; Donithan, Michele; Tonascia, James

2014-01-01

Nonalcoholic fatty liver disease (NAFLD) affects 9.6% of children and may put these children at elevated risk of high blood pressure and subsequent cardiovascular morbidity and mortality. Therefore, we sought to determine the prevalence of and risk factors for high blood pressure in children with NAFLD. Cohort study performed by the NIDDK NASH Clinical Research Network. There were 484 children with NAFLD ages 2 to 17 at enrollment; 382 children were assessed both at enrollment and 48 weeks afterwards. The main outcomes were high blood pressure at baseline and persistent high blood pressure at both baseline and 48 weeks. Prevalence of high blood pressure at baseline was 35.8% and prevalence of persistent high blood pressure was 21.4%. Children with high blood pressure were significantly more likely to have worse steatosis than children without high blood pressure (mild 19.8% vs. 34.2%, moderate 35.0% vs. 30.7%, severe 45.2% vs. 35.1%; P = 0.003). Higher body mass index, low-density lipoprotein, and uric acid were independent risk factors for high blood pressure (Odds Ratios: 1.10 per kg/m2, 1.09 per 10 mg/dL, 1.25 per mg/dL, respectively). Compared to boys, girls with NAFLD were significantly more likely to have persistent high blood pressure (28.4% vs.18.9%; P = 0.05). In conclusion, NAFLD is a common clinical problem that places children at substantial risk for high blood pressure, which may often go undiagnosed. Thus blood pressure evaluation, control, and monitoring should be an integral component of the clinical management of children with NAFLD.

Longitudinal assessment of high blood pressure in children with nonalcoholic fatty liver disease.

Directory of Open Access Journals (Sweden)

Jeffrey B Schwimmer

Full Text Available Nonalcoholic fatty liver disease (NAFLD affects 9.6% of children and may put these children at elevated risk of high blood pressure and subsequent cardiovascular morbidity and mortality. Therefore, we sought to determine the prevalence of and risk factors for high blood pressure in children with NAFLD.Cohort study performed by the NIDDK NASH Clinical Research Network. There were 484 children with NAFLD ages 2 to 17 at enrollment; 382 children were assessed both at enrollment and 48 weeks afterwards. The main outcomes were high blood pressure at baseline and persistent high blood pressure at both baseline and 48 weeks.Prevalence of high blood pressure at baseline was 35.8% and prevalence of persistent high blood pressure was 21.4%. Children with high blood pressure were significantly more likely to have worse steatosis than children without high blood pressure (mild 19.8% vs. 34.2%, moderate 35.0% vs. 30.7%, severe 45.2% vs. 35.1%; P = 0.003. Higher body mass index, low-density lipoprotein, and uric acid were independent risk factors for high blood pressure (Odds Ratios: 1.10 per kg/m2, 1.09 per 10 mg/dL, 1.25 per mg/dL, respectively. Compared to boys, girls with NAFLD were significantly more likely to have persistent high blood pressure (28.4% vs.18.9%; P = 0.05.In conclusion, NAFLD is a common clinical problem that places children at substantial risk for high blood pressure, which may often go undiagnosed. Thus blood pressure evaluation, control, and monitoring should be an integral component of the clinical management of children with NAFLD.

Comparative assessment of PIV-based pressure evaluation techniques applied to a transonic base flow

NARCIS (Netherlands)

Blinde, P; Michaelis, D; van Oudheusden, B.W.; Weiss, P.E.; de Kat, R.; Laskari, A.; Jeon, Y.J.; David, L; Schanz, D; Huhn, F.; Gesemann, S; Novara, M.; McPhaden, C.; Neeteson, N.; Rival, D.; Schneiders, J.F.G.; Schrijer, F.F.J.

2016-01-01

A test case for PIV-based pressure evaluation techniques has been developed by constructing a simulated experiment from a ZDES simulation for an axisymmetric base flow at Mach 0.7. The test case comprises sequences of four subsequent particle images (representing multi-pulse data) as well as

Relationship between the evaporation rate and vapor pressure of moderately and highly volatile chemicals.

Science.gov (United States)

van Wesenbeeck, Ian; Driver, Jeffrey; Ross, John

2008-04-01

Volatilization of chemicals can be an important form of dissipation in the environment. Rates of evaporative losses from plant and soil surfaces are useful for estimating the potential for food-related dietary residues and operator and bystander exposure, and can be used as source functions for screening models that predict off-site movement of volatile materials. A regression of evaporation on vapor pressure from three datasets containing 82 pesticidal active ingredients and co-formulants, ranging in vapor pressure from 0.0001 to >30,000 Pa was developed for this purpose with a regression correlation coefficient of 0.98.

Influence of short-term blood pressure variability on blood pressure determinations

NARCIS (Netherlands)

Bos, W. J.; van Goudoever, J.; van Montfrans, G. A.; Wesseling, K. H.

1992-01-01

To evaluate the effect of blood pressure variability on Riva Rocci Korotkoff blood pressure determinations, we studied the intra-arterial pressure during Riva Rocci Korotkoff determinations in 25 patients. In 50 measurements with a cuff deflation rate of 2.5 mm Hg/sec, the systolic intra-arterial

Evaluation of continuous and intermittent myocardial topical negative pressure

DEFF Research Database (Denmark)

Lindstedt, Sandra; Malmsjö, Malin; Gesslein, Bodil

2008-01-01

Topical negative pressure, commonly used in wound therapy, has been shown to increase blood flow and stimulate angiogenesis in subcutaneous tissue and skeletal muscle. In wound therapy, intermittent negative pressure is often preferred to continuous negative pressure as tissue exposed to intermit...

Evaluation and Optimization of Therapeutic Footwear for Neuropathic Diabetic Foot Patients Using In-Shoe Plantar Pressure Analysis

Science.gov (United States)

Bus, Sicco A.; Haspels, Rob; Busch-Westbroek, Tessa E.

2011-01-01

OBJECTIVE Therapeutic footwear for diabetic foot patients aims to reduce the risk of ulceration by relieving mechanical pressure on the foot. However, footwear efficacy is generally not assessed in clinical practice. The purpose of this study was to assess the value of in-shoe plantar pressure analysis to evaluate and optimize the pressure-reducing effects of diabetic therapeutic footwear. RESEARCH DESIGN AND METHODS Dynamic in-shoe plantar pressure distribution was measured in 23 neuropathic diabetic foot patients wearing fully customized footwear. Regions of interest (with peak pressure >200 kPa) were selected and targeted for pressure optimization by modifying the shoe or insole. After each of a maximum of three rounds of modifications, the effect on in-shoe plantar pressure was measured. Successful optimization was achieved with a peak pressure reduction of >25% (criterion A) or below an absolute level of 200 kPa (criterion B). RESULTS In 35 defined regions, mean peak pressure was significantly reduced from 303 (SD 77) to 208 (46) kPa after an average 1.6 rounds of footwear modifications (P diabetic foot. This result provides an objective approach to instantly improve footwear quality, which should reduce the risk for pressure-related plantar foot ulcers. PMID:21610125

Efficacy and safety of a therapeutic interchange from high-dose calcium channel blockers to a fixed-dose combination of amlodipine/benazepril in patients with moderate-to-severe hypertension.

Science.gov (United States)

Hilleman, D E; Reyes, A P; Wurdeman, R L; Faulkner, M

2001-08-01

Recent hypertension trials have demonstrated the importance of achieving goal blood pressures to reduce the risk of target organ damage. In patients with moderate to severe hypertension, the use of high-dose monotherapy and/or combinations of drugs are necessary to achieve these goals. Fixed-dose combination products may be useful in these patients by reducing the number of daily doses required to control blood pressure. The objective of the present study was to evaluate the efficacy and safety of a therapeutic interchange between high-dose calcium channel blocker therapy and a fixed-dose combination of amlodipine/ benazepril (Lotrel; Novartis Pharmaceuticals, USA) in patients with moderate to severe hypertension. A total of 75 patients were switched from amlodipine (n = 25), felodipine (n = 25), and nifedipine-GITS (n = 25) to amlodipine/benazepril. Twenty-eight of the 75 patients (37%) were taking either a beta-blocker or a diuretic in addition to the high-dose calcium channel blocker prior to the switch. Blood pressure control, side effects and the cost of the therapeutic interchange were evaluated in the year following the therapeutic interchange. Sixty-six of the 75 (88%) patients were successfully switched with maintenance of blood pressure control and without the development of new dose-limiting side effects. Reasons for treatment failure after the therapeutic interchange included loss of blood pressure control in five patients and the development of new dose-limiting side effects in four patients. These side effects included cough in three patients and rash in one patient. After accounting for differences in drug acquisition cost and costs related to the switch (clinic and emergency room and laboratory tests), a cost savings of $16030 for all 75 patients was realised in the first year. The per patient-per year cost savings was $214. Our data indicate that a therapeutic interchange from selected high-dose calcium channel blockers to a fixed-dose combination

Evaluation of diel patterns of relative changes in cell turgor of tomato plants using leaf patch clamp pressure probes

NARCIS (Netherlands)

Lee, K.M.; Driever, S.M.; Heuvelink, E.; Rüger, S.; Zimmermann, U.; Gelder, de A.; Marcelis, L.F.M.

2012-01-01

Relative changes in cell turgor of leaves of well-watered tomato plants were evaluated using the leaf patch clamp pressure probe (LPCP) under dynamic greenhouse climate conditions. Leaf patch clamp pressure changes, a measure for relative changes in cell turgor, were monitored at three different

Risk factors for cardiovascular disease in patients with COPD: mild-to-moderate COPD versus severe-to-very severe COPD

Directory of Open Access Journals (Sweden)

Laura Miranda de Oliveira Caram

Full Text Available ABSTRACT Objective: To assess and compare the prevalence of comorbidities and risk factors for cardiovascular disease (CVD in COPD patients according to disease severity. Methods: The study included 25 patients with mild-to-moderate COPD (68% male; mean age, 65 ± 8 years; mean FEV1, 73 ± 15% of predicted and 25 with severe-to-very severe COPD (males, 56%; mean age, 69 ± 9 years; mean FEV1, 40 ± 18% of predicted. Comorbidities were recorded on the basis of data obtained from medical charts and clinical evaluations. Comorbidities were registered on the basis of data obtained from medical charts and clinical evaluations. The Charlson comorbidity index was calculated, and the Hospital Anxiety and Depression Scale (HADS score was determined. Results: Of the 50 patients evaluated, 38 (76% had been diagnosed with at least one comorbidity, 21 (42% having been diagnosed with at least one CVD. Twenty-four patients (48% had more than one CVD. Eighteen (36% of the patients were current smokers, 10 (20% had depression, 7 (14% had dyslipidemia, and 7 (14% had diabetes mellitus. Current smoking, depression, and dyslipidemia were more prevalent among the patients with mild-to-moderate COPD than among those with severe-to-very severe COPD (p < 0.001, p = 0.008, and p = 0.02, respectively. The prevalence of high blood pressure, diabetes mellitus, alcoholism, ischemic heart disease, and chronic heart failure was comparable between the two groups. The Charlson comorbidity index and HADS scores did not differ between the groups. Conclusions: Comorbidities are highly prevalent in COPD, regardless of its severity. Certain risk factors for CVD, themselves classified as diseases (including smoking, dyslipidemia, and depression, appear to be more prevalent in patients with mild-to-moderate COPD.

Preliminary Study on the High Efficiency Supercritical Pressure Water-Cooled Reactor for Electricity Generation

Energy Technology Data Exchange (ETDEWEB)

Bae, Yoon Yeong; Park, Jong Kyun; Cho, Bong Hyun and others

2006-01-15

This research has been performed to introduce a concept of supercritical pressure water cooled reactor(SCWR) in Korea The area of research includes core conceptual design, evaluation of candidate fuel, fluid systems conceptual design with mechanical consideration, preparation of safety analysis code, and construction of supercritical pressure heat transfer test facility, SPHINX, and preliminary test. As a result of the research, a set of tools for the reactor core design has been developed and the conceptual core design with solid moderator was proposed. The direct thermodynamic cycle has been studied to find a optimum design. The safety analysis code has also been adapted to supercritical pressure condition. A supercritical pressure CO2 heat transfer test facility has been constructed and preliminary test proved the facility works as expected. The result of this project will be good basis for the participation in the international collaboration under GIF GEN-IV program and next 5-year mid and long term nuclear research program of MOST. The heat transfer test loop, SPHINX, completed as a result of this project may be used for the power cycle study as well as further heat transfer study for the various geometries.

Lack of Association between Blood Pressure Management by Anesthesia Residents and Competence Committee Evaluations or In-training Exam Performance: A Cohort Analysis.

Science.gov (United States)

Sessler, Daniel I; Makarova, Natalya; Riveros-Perez, Ricardo; Brown, David L; Kimatian, Stephen

2016-02-01

Prompt treatment of severe blood pressure instability requires both cognitive and technical skill. The ability to anticipate and respond to episodes of hemodynamic instability should improve with training. The authors tested the hypothesis that the duration of severe hypotension during anesthesia administered by residents correlates with concurrent adjusted overall performance evaluations by the Clinical Competence Committee and subsequent in-training exam scores. The authors obtained data on 70 first- and second-year anesthesia residents at the Cleveland Clinic. Analysis was restricted to adults having noncardiac surgery with general anesthesia. Outcome variables were in-training exam scores and subjective evaluations of resident performance ranked in quintiles. The primary predictor was cumulative systolic arterial pressure less than 70 mmHg. Secondary predictors were administration of vasopressors, frequency of hypotension, average duration of hypotensive episodes, and blood pressure variability. The primary statistical approach was mixed-effects modeling, adjusted for potential confounders. The authors considered 15,216 anesthesia care episodes. A total of 1,807 hypotensive episodes were observed, lasting an average of 32 ± 20 min (SD) per 100 h of anesthesia, with 68% being followed by vasopressor administration. The duration of severe hypotension (systolic pressure less than 70 mmHg) was associated with neither Competence Committee evaluations nor in-training exam scores. There was also no association between secondary blood pressure predictors and either Competence Committee evaluations or in-training exam results. There was no association between any of the five blood pressure management characteristics and either in-training exam scores or clinical competence evaluations. However, it remains possible that the measures of physiologic control, as assessed from electronic anesthesia records, evaluate useful but different aspects of anesthesiologist

Determination of mean pressure from PIV in compressible flows using the Reynolds-averaging approach

Science.gov (United States)

van Gent, Paul L.; van Oudheusden, Bas W.; Schrijer, Ferry F. J.

2018-03-01

The feasibility of computing the flow pressure on the basis of PIV velocity data has been demonstrated abundantly for low-speed conditions. The added complications occurring for high-speed compressible flows have, however, so far proved to be largely inhibitive for the accurate experimental determination of instantaneous pressure. Obtaining mean pressure may remain a worthwhile and realistic goal to pursue. In a previous study, a Reynolds-averaging procedure was developed for this, under the moderate-Mach-number assumption that density fluctuations can be neglected. The present communication addresses the accuracy of this assumption, and the consistency of its implementation, by evaluating of the relevance of the different contributions resulting from the Reynolds-averaging. The methodology involves a theoretical order-of-magnitude analysis, complemented with a quantitative assessment based on a simulated and a real PIV experiment. The assessments show that it is sufficient to account for spatial variations in the mean velocity and the Reynolds-stresses and that temporal and spatial density variations (fluctuations and gradients) are of secondary importance and comparable order-of-magnitude. This result permits to simplify the calculation of mean pressure from PIV velocity data and to validate the approximation of neglecting temporal and spatial density variations without having access to reference pressure data.

Reduction of cervical and respiratory muscle strength in patients with chronic nonspecific neck pain and having moderate to severe disability.

Science.gov (United States)

López-de-Uralde-Villanueva, Ibai; Sollano-Vallez, Ernesto; Del Corral, Tamara

2017-06-11

To investigate whether patients with chronic nonspecific neck pain and having moderate to severe disability have a greater cervical motor function impairment and respiratory disturbances compared with patients with chronic nonspecific neck pain having mild disability and asymptomatic subjects; and the association between these outcomes in patients with chronic nonspecific neck pain and healthy controls. Cross-sectional study, 44 patients with chronic nonspecific neck pain and 31 healthy subjects participated. The neck disability index was used to divide the patients into 2 groups: 1) mild disability group (scores between 5 and 14 points); and 2) moderate to severe disability group (scores >14 points). Cervical motor function was measured by cervical range of motion, forward head posture, neck flexor, and extensor muscle strength. Respiratory function and maximum respiratory pressures were also measured. Statistically differences were found between the patients with chronic nonspecific neck pain having a moderate to severe disability and the asymptomatic subjects for cervical and respiratory muscle strength. Comparisons between chronic nonspecific neck pain and the asymptomatic groups showed differences for all the variables, except for forward head posture. The regression model determined that strength of cervical flexion explained 36.4 and 45.6% of the variance of maximum inspiratory pressures and maximum expiratory pressures, respectively. Only the chronic nonspecific neck pain group with moderate to severe disability showed differences compared with the healthy subjects. Neck muscle strength could be a good predictor of respiratory muscle function. Implications for rehabilitation Neck pain severity could be closely associated with decreased respiratory pressure in patients with chronic nonspecific neck pain. These findings suggest a new therapeutic approach for patients with moderate to severe disability, such as respiratory muscle training. The regression

Consequence evaluation of radiation embrittlement of Trojan reactor pressure vessel supports

International Nuclear Information System (INIS)

Lu, S.C.

1990-01-01

The consequences evaluation of radiation embrittlement of reactor pressure vessel (RPV) supports of nuclear power plants offers a more direct and less controversial approach to the safety concerns addressed by Generic Safety Issue 15(GSI-15) identified by the U.S. Nuclear Regulatory Commission (NRC) because this approach depends on more conventional methodologies widely accepted by the engineering community. The success of this evaluation may permit a satisfactory resolution to GSI-15 by demonstrating that even under the most unfavorable circumstances, i.e., complete failure of all RPV supports, there is no undue risk to public safety. This evaluation is divided into two phases. Phase 1 is a pilot study on a selected nuclear power plant. Phase 2 is a parametric study undertaken in an attempt to generalize the conclusion of the pilot study to other nuclear power plants. The Trojan nuclear power plant was selected for the pilot study because its RPV supports are located in the high radiation zone and are subject to high tensile stresses. The pilot study comprises a structural evaluation and an effect evaluation and assumes that all four RPV supports have completely lost their load carrying capability. The current paper addresses Phase 1 results and conclusions

Knowledge of pressure ulcer prevention: a cross-sectional and comparative study among nurses

Directory of Open Access Journals (Sweden)

Bours Gerrie JJW

2007-03-01

Full Text Available Abstract Background Pressure ulcers are a common, painful and costly condition. Results of a 1991 study into the knowledge among Dutch hospital nurses on the usefulness of measures to prevent pressure ulcers showed moderate knowledge. Results were confirmed by subsequent studies. In recent years, Dutch guidelines have been updated and the attention given to pressure ulcer care has been increased. This was expected to improve pressure ulcer care and to increase nurses' knowledge. The aims of the current study were to investigate (1 how much nurses employed in Dutch hospitals know about the usefulness of 28 preventive measures considered in the most recent national pressure ulcer guideline; (2 whether differences in knowledge exist between nurses working in hospitals that audit pressure ulcers and those employed in hospitals that do not; and (3 to study whether knowledge among Dutch hospital nurses regarding the usefulness of preventive measures had changed between 1991 and 2003. Methods A cross-sectional study design among nurses employed in Dutch hospitals in 2003 was used to investigate their knowledge and differences in knowledge between nurses employed in different types of institution. A comparative design was used to assess whether knowledge differed between this population and that of Dutch hospital nurses in 1991. The nurses' knowledge was assessed by a written questionnaire. Data of 522 respondents meeting the inclusion criteria were analyzed and compared with the results of the 351 nurses included in the 1991 study. Results Knowledge in 2003 was slightly better than that in 1991. The nurses were moderately aware of the usefulness of preventive measures. Nurses employed in organizations that monitored pressure ulcers did not display greater knowledge than those employed in organizations that did not do so. Conclusion Knowledge among Dutch hospital nurses about the usefulness of measures to prevent pressure ulcers seems to be moderate

Blood pressure reduction, persistence and costs in the evaluation of antihypertensive drug treatment – a review

Directory of Open Access Journals (Sweden)

Hasford Joerg

2009-03-01

Full Text Available Abstract Background Blood pressure lowering drugs are usually evaluated in short term trials determining the absolute blood pressure reduction during trough and the duration of the antihypertensive effect after single or multiple dosing. A lack of persistence with treatment has however been shown to be linked to a worse cardiovascular prognosis. This review explores the blood pressure reduction and persistence with treatment of antihypertensive drugs and the cost consequences of poor persistence with pharmaceutical interventions in arterial hypertension. Methods We have searched the literature for data on blood pressure lowering effects of different antihypertensive drug classes and agents, on persistence with treatment, and on related costs. Persistence was measured as patients' medication possession rate. Results are presented in the form of a systematic review. Results Angiotensin II receptor blocker (ARBs have a competitive blood pressure lowering efficacy compared with ACE-inhibitors (ACEi and calcium channel blockers (CCBs, beta-blockers (BBs and diuretics. 8 studies describing the persistence with treatment were identified. Patients were more persistent on ARBs than on ACEi and CCBs, BBs and diuretics. Thus the product of blood pressure lowering and persistence was higher on ARBs than on any other drug class. Although the price per tablet of more recently developed drugs (ACEi, ARBs is higher than that of older ones (diuretics and BBs, the newer drugs result in a more favourable cost to effect ratio when direct drug costs and indirect costs are also considered. Conclusion To evaluate drugs for the treatment of hypertension several key variables including the blood pressure lowering effect, side effects, compliance/persistence with treatment, as well as drug costs and direct and indirect costs of medical care have to be considered. ARBs, while nominally more expensive when drug costs are considered only, provide substantial cost savings

Eating Behaviours of Preadolescent Children over Time: Stability, Continuity and the Moderating Role of Perceived Parental Feeding Practices

Directory of Open Access Journals (Sweden)

Laura Houldcroft

2016-04-01

Full Text Available The links between childhood eating behaviours and parental feeding practices are well-established in younger children, but there is a lack of research examining these variables in a preadolescent age group, particularly from the child’s perspective, and longitudinally. This study firstly aimed to examine the continuity and stability of preadolescent perceptions of their parents’ controlling feeding practices (pressure to eat and restriction over a 12 month period. The second aim was to explore if perceptions of parental feeding practices moderated the relationship between preadolescents’ eating behaviours longitudinally. Two hundred and twenty nine preadolescents (mean age at recruitment 8.73 years completed questionnaires assessing their eating behaviours and their perceptions of parental feeding practices at two time points, 12 months apart (T1 and T2. Preadolescents’ perceptions of their parental feeding practices remained stable. Perceptions of restriction and pressure to eat were continuous. Perceptions of parental pressure to eat and restriction significantly moderated the relationships between eating behaviours at T1 and T2. The findings from this study suggest that in a preadolescent population, perceptions of parental pressure to eat and restriction of food may exacerbate the development of problematic eating behaviours.

Food parenting practices and child dietary behavior. Prospective relations and the moderating role of general parenting.

Science.gov (United States)

Sleddens, Ester F C; Kremers, Stef P J; Stafleu, Annette; Dagnelie, Pieter C; De Vries, Nanne K; Thijs, Carel

2014-08-01

Research on parenting practices has focused on individual behaviors while largely failing to consider the context of their use, i.e., general parenting. We examined the extent to which food parenting practices predict children's dietary behavior (classified as unhealthy: snacking, sugar-sweetened beverage; and healthy: water and fruit intake). Furthermore, we tested the moderating role of general parenting on this relationship. Within the KOALA Birth Cohort Study, in the Netherlands, questionnaire data were collected at 6 and 8 years (N = 1654). Correlations were computed to assess the association between food parenting practices and general parenting (i.e., nurturance, behavioral control, structure, coercive control, and overprotection). Linear regression models were fitted to assess whether food parenting practices predict dietary behavior. Instrumental and emotional feeding, and pressure to eat were found to have associations with undesirable child dietary behavior (increased unhealthy intake/decreased healthy intake), whereas associations were in the desirable direction for covert control, encouragement and restriction. Moderation analyses were performed by evaluating interactions with general parenting. The associations of encouragement and covert control with desirable child dietary behaviors were found to be stronger for children who were reared in a positive parenting context. Future research should assess the influence of contextual parenting factors moderating the relationships between food parenting and child dietary behavior as the basis for the development of more effective family-based interventions. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development and psychometric validation of a questionnaire to evaluate nurses' adherence to recommendations for preventing pressure ulcers (QARPPU).

Science.gov (United States)

Moya-Suárez, Ana Belén; Morales-Asencio, José Miguel; Aranda-Gallardo, Marta; Enríquez de Luna-Rodríguez, Margarita; Canca-Sánchez, José Carlos

2017-11-01

The main objective of this work is the development and psychometric validation of an instrument to evaluate nurses' adherence to the main recommendations issued for preventing pressure ulcers. An instrument was designed based on the main recommendations for the prevention of pressure ulcers published in various clinical practice guides. Subsequently, it was proceeded to evaluate the face and content validity of the instrument by an expert group. It has been applied to 249 Spanish nurses took part in a cross-sectional study to obtain a psychometric evaluation (reliability and construct validity) of the instrument. The study data were compiled from June 2015 to July 2016. From the results of the psychometric analysis, a final 18-item, 4-factor questionnaire was derived, which explained 60.5% of the variance and presented the following optimal indices of fit (CMIN/DF: 1.40 p < 0.001; GFI: 0.93; NFI: 0.92; CFI: 0.98; TLI: 0.97; RMSEA: 0.04 (90% CI 0.025-0.054). The results obtained show that the instrument presents suitable psychometric properties for evaluating nurses' adherence to recommendations for the prevention of pressure ulcers. Copyright © 2017 Tissue Viability Society. Published by Elsevier Ltd. All rights reserved.

Exercise excess pressure and exercise-induced albuminuria in patients with type 2 diabetes mellitus.

Science.gov (United States)

Climie, Rachel E D; Srikanth, Velandai; Keith, Laura J; Davies, Justin E; Sharman, James E

2015-05-01

Exercise-induced albuminuria is common in patients with type 2 diabetes mellitus (T2DM) in response to maximal exercise, but the response to light-moderate exercise is unclear. Patients with T2DM have abnormal central hemodynamics and greater propensity for exercise hypertension. This study sought to determine the relationship between light-moderate exercise central hemodynamics (including aortic reservoir and excess pressure) and exercise-induced albuminuria. Thirty-nine T2DM (62 ± 9 yr; 49% male) and 39 nondiabetic controls (53 ± 9 yr; 51% male) were examined at rest and during 20 min of light-moderate cycle exercise (30 W; 50 revolutions/min). Albuminuria was assessed by the albumin-creatinine ratio (ACR) at rest and 30 min postexercise. Hemodynamics recorded included brachial and central blood pressure (BP), aortic stiffness, augmented pressure (AP), aortic reservoir pressure, and excess pressure integral (Pexcess). There was no difference in ACR between groups before exercise (P > 0.05). Exercise induced a significant rise in ACR in T2DM but not controls (1.73 ± 1.43 vs. 0.53 ± 1.0 mg/mol, P = 0.002). All central hemodynamic variables were significantly higher during exercise in T2DM (i.e., Pexcess, systolic BP and AP; P exercise Pexcess was associated with postexercise ACR (r = 0.51, P = 0.002), and this relationship was independent of age, sex, body mass index, heart rate, aortic stiffness, antihypertensive medication, and ambulatory daytime systolic BP (β = 0.003, P = 0.003). Light-moderate exercise induced a significant rise in ACR in T2DM, and this was independently associated with Pexcess, a potential marker of vascular dysfunction. These novel findings suggest that Pexcess could be important for appropriate renal function in T2DM. Copyright © 2015 the American Physiological Society.

HFIR cold neutron source moderator vessel design analysis

International Nuclear Information System (INIS)

Chang, S.J.

1998-04-01

A cold neutron source capsule made of aluminum alloy is to be installed and located at the tip of one of the neutron beam tubes of the High Flux Isotope Reactor. Cold hydrogen liquid of temperature approximately 20 degree Kelvin and 15 bars pressure is designed to flow through the aluminum capsule that serves to chill and to moderate the incoming neutrons produced from the reactor core. The cold and low energy neutrons thus produced will be used as cold neutron sources for the diffraction experiments. The structural design calculation for the aluminum capsule is reported in this paper

Evaluation of high-pressure containment buildings for LMFBR's

International Nuclear Information System (INIS)

Armstrong, G.R.

1981-01-01

A study was conducted on the use of High Pressure LMFBR Containment Buildings for 1000 MW(e) LMFBRs. Two principal aspects were investigated: accident consequence mitigation and cost. Two types of hypothetical accidents were analyzed to establish consequence mitigation: melt-through and energetic expulsion. Three Containment Building (CB) design pressures were investigated: 69 kPa (10 psig), 207 kPa (30 psig), and 414 kPa (60 psig). Four types of design structures were analyzed to establish cost: steel, steel with confinement building, reinforced concrete, and prestressed/post-tensioned concrete. Results show that: it is within reason that a high pressure containment for a 1000 MW(e) reactor can be fabricated that will retain its integrity during postulated severe hypothetical accidents, if available measures are taken to reduce or prevent hydrogen production and the cost differential between basic high (414 kPa) and low (69 kPa) pressure containments is $10 x 10 6 or less

Performance Evaluation of Pressure Transducers for Water Impacts

Science.gov (United States)

Vassilakos, Gregory J.; Stegall, David E.; Treadway, Sean

2012-01-01

The Orion Multi-Purpose Crew Vehicle is being designed for water landings. In order to benchmark the ability of engineering tools to predict water landing loads, test programs are underway for scale model and full-scale water impacts. These test programs are predicated on the reliable measurement of impact pressure histories. Tests have been performed with a variety of pressure transducers from various manufacturers. Both piezoelectric and piezoresistive devices have been tested. Effects such as thermal shock, pinching of the transducer head, and flushness of the transducer mounting have been studied. Data acquisition issues such as sampling rate and anti-aliasing filtering also have been studied. The response of pressure transducers have been compared side-by-side on an impulse test rig and on a 20-inch diameter hemisphere dropped into a pool of water. The results have identified a range of viable configurations for pressure measurement dependent on the objectives of the test program.

Blood pressure modifies retinal susceptibility to intraocular pressure elevation.

Directory of Open Access Journals (Sweden)

Zheng He

Full Text Available Primary open angle glaucoma affects more than 67 million people. Elevated intraocular pressure (IOP is a risk factor for glaucoma and may reduce nutrient availability by decreasing ocular perfusion pressure (OPP. An interaction between arterial blood pressure and IOP determines OPP; but the exact contribution that these factors have for retinal function is not fully understood. Here we sought to determine how acute modifications of arterial pressure will affect the susceptibility of neuronal function and blood flow to IOP challenge. Anaesthetized (ketamine:xylazine Long-Evan rats with low (∼60 mmHg, sodium nitroprusside infusion, moderate (∼100 mmHg, saline, or high levels (∼160 mmHg, angiotensin II of mean arterial pressure (MAP, n = 5-10 per group were subjected to IOP challenge (10-120 mmHg, 5 mmHg steps every 3 minutes. Electroretinograms were measured at each IOP step to assess bipolar cell (b-wave and inner retinal function (scotopic threshold response or STR. Ocular blood flow was measured using laser-Doppler flowmetry in groups with similar MAP level and the same IOP challenge protocol. Both b-wave and STR amplitudes decreased with IOP elevation. Retinal function was less susceptible to IOP challenge when MAP was high, whereas the converse was true for low MAP. Consistent with the effects on retinal function, higher IOP was needed to attenuated ocular blood flow in animals with higher MAP. The susceptibility of retinal function to IOP challenge can be ameliorated by acute high BP, and exacerbated by low BP. This is partially mediated by modifications in ocular blood flow.

Evaluation of fatigue damage of pressure vessel materials by observation of microstructures

International Nuclear Information System (INIS)

Yoshida, Kazuo

1994-01-01

As the important factor as the secular change mode of pressure vessel materials, there is fatigue damage. In USA, there is the move to use LWRs by extending their life, and it becomes necessary to show the soundness of the structures of machinery and equipment for long period. For exactly evaluating the soundness of the structures of machinery and equipment, it is important to clarify the degree of secular deterioration of the materials. In this report, by limiting to the fatigue damage of LWR pressure vessel steel, the method of grasping the change of microstructure and the method of estimating the degree of fatigue damage from the change of microstructure are shown. The change of microstructure arising in materials due to fatigue advances in the following steps, namely, the multiplication of dislocations, the tangling of dislocations, the formation of cell structure, the turning of cells, the formation of microcracks, the growth of cracks and fracture. In the case of pressure vessel steel, due to the quenching and tempering, the cell structure is formed from the beginning, and the advance of fatigue is recognized as the increase of the turning angle of cell structures. The detection of fatigue damage by microstructure is reported. (K.I.)

High-frequency pressure variations in the vicinity of a surface CO2 flux chamber

Science.gov (United States)

Eugene S. Takle; James R. Brandle; R. A. Schmidt; Rick Garcia; Irina V. Litvina; William J. Massman; Xinhua Zhou; Geoffrey Doyle; Charles W. Rice

2003-01-01

We report measurements of 2Hz pressure fluctuations at and below the soil surface in the vicinity of a surface-based CO2 flux chamber. These measurements were part of a field experiment to examine the possible role of pressure pumping due to atmospheric pressure fluctuations on measurements of surface fluxes of CO2. Under the moderate wind speeds, warm temperatures,...

Surgical Space Conditions During Low-Pressure Laparoscopic Cholecystectomy with Deep Versus Moderate Neuromuscular Blockade

DEFF Research Database (Denmark)

Staehr-Rye, Anne K; Rasmussen, Lars S.; Rosenberg, Jacob

2014-01-01

: In this assessor-blinded study, 48 patients undergoing elective laparoscopic cholecystectomy were administered rocuronium for neuromuscular blockade and randomized to either deep neuromuscular blockade (rocuronium bolus plus infusion maintaining a posttetanic count 0-1) or moderate neuromuscular blockade...... (rocuronium repeat bolus only for inadequate surgical conditions with spontaneous recovery of neuromuscular function). Patients received anesthesia with propofol, remifentanil, and rocuronium. The primary outcome was the proportion of procedures with optimal surgical space conditions (assessed by the surgeon...

Combined exercise circuit session acutely attenuates stress-induced blood pressure reactivity in healthy adults

Directory of Open Access Journals (Sweden)

Sérgio R. Moreira

2014-03-01

Full Text Available Objective: To investigate the blood pressure (BP responses to cardiovascular stress test after a combined exercise circuit session at moderate intensity. Method: Twenty individuals (10 male/10 fem; 33.4± 6.9 years; 70.2± 15.8 kg; 170.4± 11.5 cm; 22.3± 6.8% body fat were randomized in a different days to control session with no exercise or exercise session consisting of 3 laps of the following circuit: knee extension, bench press, knee flexion, rowing in the prone position, squats, shoulder press, and 5 min of aerobic exercise at 75-85% of age-predicted maximum heart rate and/or 13 on the Borg Rating of Perceived Exertion [scale of 6 to 20]. The sets of resistance exercise consisted of 15 repetitions at ~50% of the estimated 1 repetition maximum test. Systolic blood pressure (SBP and diastolic blood pressure (DBP were measured at rest and during 1h of recovery in both experimental sessions. After that, blood pressure reactivity (BPR was evaluated using the Cold Pressor Test. Results: During 1h of exercise recovery, there was a reduction in SBP (3-6 mmHg and DBP (2-5 mmHg in relation to pre-session rest (p<0.01, while this reduction was not observed in the control session. A decline in BPR (4-7 mmHg; p<0.01 was observed 1h post-exercise session, but not in the control session. Post-exercise reductions in SBP and DBP were significantly correlated with BPR reductions (r=0.50-0.45; p<0.05. Conclusion: A combined exercise circuit session at moderate intensity promoted subsequent post-exercise hypotension and acutely attenuated BPR in response to a cardiovascular stress test. In addition, the post-exercise BP reduction was correlated with BPR attenuation in healthy adults of both genders.

Nocturnal Blood Pressure Variability in Patients with Obstructive Sleep Apnea Syndrome.

Science.gov (United States)

Martynowicz, H; Porębska, I; Poręba, R; Mazur, G; Brzecka, A

2016-01-01

Obstructive sleep apnea (OSA) is a common respiratory disorder associated with hypertension and cardiovascular complications. Blood pressure variability may be a sign of risk of cardiovascular events. The aim of this study was to investigate the hypothesis that severe OSA syndrome is associated with increased blood pressure variability. Based on respiratory polygraphy, 58 patients were categorized into two groups: severe OSA with apnea/hypopnea index (AHI) greater than 29 episodes per hour (mean 52.2 ± 19.0/h) and mild-to-moderate OSA with AHI between 5 and 30 episodes per hour (mean 20.2 ± 7.8/h). A 24-h noninvasive blood pressure monitoring was performed. The standard deviation of mean blood pressure was used as the indicator of blood pressure variability. In patients with severe, compared with mild-to-moderate OSA, a higher mean nocturnal systolic blood pressure (133.2 ± 17.4 mmHg vs. 117.7 ± 31.2 mmHg, p variability (12.1 ± 6.0 vs. 7.6 ± 4.3, p variability (10.5 ± 6.1 vs. 7.3 ± 4.0 p variability (9.1 ± 4.9 mmHg vs. 6.8 ± 3.5 mmHg) were detected. The findings of the study point to increased nocturnal systolic and diastolic arterial blood pressure and blood pressure variability as risk factors of cardiovascular complications in patients with severe OSA.

Moderate and extreme maternal obesity.

LENUS (Irish Health Repository)