WorldWideScience

Sample records for modeling section ends

  1. Water quality modeling in the dead end sections of drinking water (Supplement)

    Data.gov (United States)

    U.S. Environmental Protection Agency — Dead-end sections of drinking water distribution networks are known to be problematic zones in terms of water quality degradation. Extended residence time due to...

  2. Water quality modeling in the dead end sections of drinking water distribution networks.

    Science.gov (United States)

    Abokifa, Ahmed A; Yang, Y Jeffrey; Lo, Cynthia S; Biswas, Pratim

    2016-02-01

    Dead-end sections of drinking water distribution networks are known to be problematic zones in terms of water quality degradation. Extended residence time due to water stagnation leads to rapid reduction of disinfectant residuals allowing the regrowth of microbial pathogens. Water quality models developed so far apply spatial aggregation and temporal averaging techniques for hydraulic parameters by assigning hourly averaged water demands to the main nodes of the network. Although this practice has generally resulted in minimal loss of accuracy for the predicted disinfectant concentrations in main water transmission lines, this is not the case for the peripheries of the distribution network. This study proposes a new approach for simulating disinfectant residuals in dead end pipes while accounting for both spatial and temporal variability in hydraulic and transport parameters. A stochastic demand generator was developed to represent residential water pulses based on a non-homogenous Poisson process. Dispersive solute transport was considered using highly dynamic dispersion rates. A genetic algorithm was used to calibrate the axial hydraulic profile of the dead-end pipe based on the different demand shares of the withdrawal nodes. A parametric sensitivity analysis was done to assess the model performance under variation of different simulation parameters. A group of Monte-Carlo ensembles was carried out to investigate the influence of spatial and temporal variations in flow demands on the simulation accuracy. A set of three correction factors were analytically derived to adjust residence time, dispersion rate and wall demand to overcome simulation error caused by spatial aggregation approximation. The current model results show better agreement with field-measured concentrations of conservative fluoride tracer and free chlorine disinfectant than the simulations of recent advection dispersion reaction models published in the literature. Accuracy of the simulated

  3. OISI dynamic end-to-end modeling tool

    Science.gov (United States)

    Kersten, Michael; Weidler, Alexander; Wilhelm, Rainer; Johann, Ulrich A.; Szerdahelyi, Laszlo

    2000-07-01

    The OISI Dynamic end-to-end modeling tool is tailored to end-to-end modeling and dynamic simulation of Earth- and space-based actively controlled optical instruments such as e.g. optical stellar interferometers. `End-to-end modeling' is meant to denote the feature that the overall model comprises besides optical sub-models also structural, sensor, actuator, controller and disturbance sub-models influencing the optical transmission, so that the system- level instrument performance due to disturbances and active optics can be simulated. This tool has been developed to support performance analysis and prediction as well as control loop design and fine-tuning for OISI, Germany's preparatory program for optical/infrared spaceborne interferometry initiated in 1994 by Dornier Satellitensysteme GmbH in Friedrichshafen.

  4. Field quality of the end sections of SSC [Superconducting Super Collider] dipoles

    International Nuclear Information System (INIS)

    Hassenzahl, W.V.; Caspi, S.; Gilbert, W.; Helm, M.; Laslett, L.J.; Morgan, G.A.

    1986-09-01

    The central or two-dimensional field of a dipole magnet can be calculated with some precision. The fields at the end of the magnet, which are three-dimensional in nature, provide a more complicated problem. Starting with an end design that produced a relatively good end in terms of multipole components, a method of extending parts of the straight section was used to reduce the most important harmonics, the sextupole and decapole, to a negligible level. In addition, the effect of extending an iron yoke over the ends of a magnet was investigated and it was found to have little effect on the harmonics, though it will raise the dipole field. These results are encouraging as they imply that good ends can be developed with relative ease should the two dimensional cross-section of a dipole magnet such as the SSC have to be changed

  5. Modeling and simulation of satellite subsystems for end-to-end spacecraft modeling

    Science.gov (United States)

    Schum, William K.; Doolittle, Christina M.; Boyarko, George A.

    2006-05-01

    During the past ten years, the Air Force Research Laboratory (AFRL) has been simultaneously developing high-fidelity spacecraft payload models as well as a robust distributed simulation environment for modeling spacecraft subsystems. Much of this research has occurred in the Distributed Architecture Simulation Laboratory (DASL). AFRL developers working in the DASL have effectively combined satellite power, attitude pointing, and communication link analysis subsystem models with robust satellite sensor models to create a first-order end-to-end satellite simulation capability. The merging of these two simulation areas has advanced the field of spacecraft simulation, design, and analysis, and enabled more in-depth mission and satellite utility analyses. A core capability of the DASL is the support of a variety of modeling and analysis efforts, ranging from physics and engineering-level modeling to mission and campaign-level analysis. The flexibility and agility of this simulation architecture will be used to support space mission analysis, military utility analysis, and various integrated exercises with other military and space organizations via direct integration, or through DOD standards such as Distributed Interaction Simulation. This paper discusses the results and lessons learned in modeling satellite communication link analysis, power, and attitude control subsystems for an end-to-end satellite simulation. It also discusses how these spacecraft subsystem simulations feed into and support military utility and space mission analyses.

  6. Model outputs - Developing end-to-end models of the Gulf of California

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The purpose of this project is to develop spatially discrete end-to-end models of the northern Gulf of California, linking oceanography, biogeochemistry, food web...

  7. A gastrocnemius heterotopical transplant model with end-to-side neurorraphy.

    Science.gov (United States)

    Jaeger, Marcos Ricardo de Oliveira; Silva, Jefferson Luis Braga; Bain, James; Ely, Pedro Bins; Pires, Jefferson André; Ferreira, Lydia Masako

    2014-01-01

    To present an animal model to assess the effects of end-to-side innervation in the heterotopically transplanted model with reduced chances of neural contamination. The medial portion of the gastrocnemius muscle in wistar male rats was isolated and its pedicle dissected and performed a flap in the abdominal portion. To prevent neural contamination in the abdominal region, the muscle was wrapped with a Goretex(r) sheet. The specimens were divided into 2 groups (G). In G1 was performed an end-to-end suture between tibial nerve of the gastrocnemius and femoral motor nerve and between the saphenous sensory nerve and the motor nerve. In G2 was performed a end-to-side suture between the tibial nerve and the motor femoral and between the tibial nerve and saphenous motor nerve. The specimens were evaluated 60 days later to check the structure of the neurorraphy. Sections were obtained proximal and distal to the coaptation site. The medial gastrocnemius muscle had the advantage of maintaining visible mass after 60 days. No disruption of the coaptation site was found. No major injury to the donor nerve was seen in group 2. The proposed model is simple, reproduciple and prevent the neural contamination in the flap in end-to-side suture.

  8. Development of a Dynamic, End-to-End Free Piston Stirling Convertor Model

    Science.gov (United States)

    Regan, Timothy F.; Gerber, Scott S.; Roth, Mary Ellen

    2003-01-01

    A dynamic model for a free-piston Stirling convertor is being developed at the NASA Glenn Research Center. The model is an end-to-end system model that includes the cycle thermodynamics, the dynamics, and electrical aspects of the system. The subsystems of interest are the heat source, the springs, the moving masses, the linear alternator, the controller and the end-user load. The envisioned use of the model will be in evaluating how changes in a subsystem could affect the operation of the convertor. The model under development will speed the evaluation of improvements to a subsystem and aid in determining areas in which most significant improvements may be found. One of the first uses of the end-to-end model will be in the development of controller architectures. Another related area is in evaluating changes to details in the linear alternator.

  9. A Bayes Theory-Based Modeling Algorithm to End-to-end Network Traffic

    Directory of Open Access Journals (Sweden)

    Zhao Hong-hao

    2016-01-01

    Full Text Available Recently, network traffic has exponentially increasing due to all kind of applications, such as mobile Internet, smart cities, smart transportations, Internet of things, and so on. the end-to-end network traffic becomes more important for traffic engineering. Usually end-to-end traffic estimation is highly difficult. This paper proposes a Bayes theory-based method to model the end-to-end network traffic. Firstly, the end-to-end network traffic is described as a independent identically distributed normal process. Then the Bases theory is used to characterize the end-to-end network traffic. By calculating the parameters, the model is determined correctly. Simulation results show that our approach is feasible and effective.

  10. A Bayes Theory-Based Modeling Algorithm to End-to-end Network Traffic

    OpenAIRE

    Zhao Hong-hao; Meng Fan-bo; Zhao Si-wen; Zhao Si-hang; Lu Yi

    2016-01-01

    Recently, network traffic has exponentially increasing due to all kind of applications, such as mobile Internet, smart cities, smart transportations, Internet of things, and so on. the end-to-end network traffic becomes more important for traffic engineering. Usually end-to-end traffic estimation is highly difficult. This paper proposes a Bayes theory-based method to model the end-to-end network traffic. Firstly, the end-to-end network traffic is described as a independent identically distrib...

  11. End-to-End Delay Model for Train Messaging over Public Land Mobile Networks

    Directory of Open Access Journals (Sweden)

    Franco Mazzenga

    2017-11-01

    Full Text Available Modern train control systems rely on a dedicated radio network for train to ground communications. A number of possible alternatives have been analysed to adopt the European Rail Traffic Management System/European Train Control System (ERTMS/ETCS control system on local/regional lines to improve transport capacity. Among them, a communication system based on public networks (cellular&satellite provides an interesting, effective and alternative solution to proprietary and expensive radio networks. To analyse performance of this solution, it is necessary to model the end-to-end delay and message loss to fully characterize the message transfer process from train to ground and vice versa. Starting from the results of a railway test campaign over a 300 km railway line for a cumulative 12,000 traveled km in 21 days, in this paper, we derive a statistical model for the end-to-end delay required for delivering messages. In particular, we propose a two states model allowing for reproducing the main behavioral characteristics of the end-to-end delay as observed experimentally. Model formulation has been derived after deep analysis of the recorded experimental data. When it is applied to model a realistic scenario, it allows for explicitly accounting for radio coverage characteristics, the received power level, the handover points along the line and for the serving radio technology. As an example, the proposed model is used to generate the end-to-end delay profile in a realistic scenario.

  12. Atlantis model outputs - Developing end-to-end models of the California Current Large Marine Ecosystem

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The purpose of this project is to develop spatially discrete end-to-end models of the California Current LME, linking oceanography, biogeochemistry, food web...

  13. End-to-end network models encompassing terrestrial, wireless, and satellite components

    Science.gov (United States)

    Boyarko, Chandler L.; Britton, John S.; Flores, Phil E.; Lambert, Charles B.; Pendzick, John M.; Ryan, Christopher M.; Shankman, Gordon L.; Williams, Ramon P.

    2004-08-01

    Development of network models that reflect true end-to-end architectures such as the Transformational Communications Architecture need to encompass terrestrial, wireless and satellite component to truly represent all of the complexities in a world wide communications network. Use of best-in-class tools including OPNET, Satellite Tool Kit (STK), Popkin System Architect and their well known XML-friendly definitions, such as OPNET Modeler's Data Type Description (DTD), or socket-based data transfer modules, such as STK/Connect, enable the sharing of data between applications for more rapid development of end-to-end system architectures and a more complete system design. By sharing the results of and integrating best-in-class tools we are able to (1) promote sharing of data, (2) enhance the fidelity of our results and (3) allow network and application performance to be viewed in the context of the entire enterprise and its processes.

  14. Analysis of a DSM program using an end use model; End use model wo mochiita DSM program no bunseki

    Energy Technology Data Exchange (ETDEWEB)

    Asano, H.; Takahashi, M.; Okada, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-01-30

    An end use model used in the United States who is advanced in demand-side management (DSM) was used to discuss possibilities of designing and evaluating Japan`s future DSM measures. The end use model assumes energy demand based on such factors as device characteristics, meteorological data, energy prices, user characteristics, market characteristics and DSM measures. The model calculates energy demand amount by end uses basically by multiplying assumptions on device unit requirement, device retention rate, and number of users. A representative tool as an end use model that handles load shapes is the hourly electric load model (HELM). It assumes an annual load curve and predicts a maximum system load. The present discussions have performed estimation on demand for consumer use air conditioners in a day in which a maximum summer load occurs in a reference year, estimation on load in a maximum load day in an estimated year, and estimation on weather sensitivity of loads. 5 refs., 5 figs.

  15. Modeling Non-homologous End Joining

    Science.gov (United States)

    Li, Yongfeng

    2013-01-01

    Non-homologous end joining (NHEJ) is the dominant DNA double strand break (DSB) repair pathway and involves several NHEJ proteins such as Ku, DNA-PKcs, XRCC4, Ligase IV and so on. Once DSBs are generated, Ku is first recruited to the DNA end, followed by other NHEJ proteins for DNA end processing and ligation. Because of the direct ligation of break ends without the need for a homologous template, NHEJ turns out to be an error-prone but efficient repair pathway. Some mechanisms have been proposed of how the efficiency of NHEJ repair is affected. The type of DNA damage is an important factor of NHEJ repair. For instance, the length of DNA fragment may determine the recruitment efficiency of NHEJ protein such as Ku [1], or the complexity of the DNA breaks [2] is accounted for the choice of NHEJ proteins and subpathway of NHEJ repair. On the other hand, the chromatin structure also plays a role of the accessibility of NHEJ protein to the DNA damage site. In this talk, some mathematical models of NHEJ, that consist of series of biochemical reactions complying with the laws of chemical reaction (e.g. mass action, etc.), will be introduced. By mathematical and numerical analysis and parameter estimation, the models are able to capture the qualitative biological features and show good agreement with experimental data. As conclusions, from the viewpoint of modeling, how the NHEJ proteins are recruited will be first discussed for connection between the classical sequential model [4] and recently proposed two-phase model [5]. Then how the NHEJ repair pathway is affected, by the length of DNA fragment [6], the complexity of DNA damage [7] and the chromatin structure [8], will be addressed

  16. General Practitioners' Attitudes towards Essential Competencies in End-of-Life Care: A Cross-Sectional Survey.

    Science.gov (United States)

    Giezendanner, Stéphanie; Jung, Corinna; Banderet, Hans-Ruedi; Otte, Ina Carola; Gudat, Heike; Haller, Dagmar M; Elger, Bernice S; Zemp, Elisabeth; Bally, Klaus

    2017-01-01

    Identifying essential competencies in end-of-life care, as well as general practitioners' (GPs) confidence in these competencies, is essential to guide training and quality improvement efforts in this domain. To determine which competencies in end-of-life care are considered important by GPs, to assess GPs' confidence in these competencies in a European context and their reasons to refer terminally ill patients to a specialist. Cross-sectional postal survey involving a stratified random sample of 2000 GPs in Switzerland in 2014. Survey development was informed by a previous qualitative exploration of relevant end-of-life GP competencies. Main outcome measures were GPs' assessment of the importance of and confidence in 18 attributes of end-of-life care competencies, and reasons for transferring care of terminally-ill patients to a specialist. GP characteristics associated with main outcome measures were tested using multivariate regression models. The response rate was 31%. Ninety-nine percent of GPs considered the recognition and treatment of pain as important, 86% felt confident about it. Few GPs felt confident in cultural (16%), spiritual (38%) and legal end-of-life competencies such as responding to patients seeking assisted suicide (35%) although more than half of the respondents regarded these competencies as important. Most frequent reasons to refer terminally ill patients to a specialist were lack of time (30%), better training of specialists (23%) and end-of-life care being incompatible with other duties (19%). In multiple regression analyses, confidence in end-of-life care was positively associated with GPs' age, practice size, home visits and palliative training. GPs considered non-somatic competencies (such as spiritual, cultural, ethical and legal aspects) nearly as important as pain and symptom control. Yet, few GPs felt confident in these non-somatic competencies. These findings should inform training and quality improvement efforts in this domain, in

  17. QoS Modeling for End-to-End Performance Evaluation over Networks with Wireless Access

    Directory of Open Access Journals (Sweden)

    Gómez Gerardo

    2010-01-01

    Full Text Available This paper presents an end-to-end Quality of Service (QoS model for assessing the performance of data services over networks with wireless access. The proposed model deals with performance degradation across protocol layers using a bottom-up strategy, starting with the physical layer and moving on up to the application layer. This approach makes it possible to analytically assess performance at different layers, thereby facilitating a possible end-to-end optimization process. As a representative case, a scenario where a set of mobile terminals connected to a streaming server through an IP access node has been studied. UDP, TCP, and the new TCP-Friendly Rate Control (TFRC protocols were analyzed at the transport layer. The radio interface consisted of a variable-rate multiuser and multichannel subsystem, including retransmissions and adaptive modulation and coding. The proposed analytical QoS model was validated on a real-time emulator of an end-to-end network with wireless access and proved to be very useful for the purposes of service performance estimation and optimization.

  18. Quantification of Back-End Nuclear Fuel Cycle Metrics Uncertainties Due to Cross Sections

    International Nuclear Information System (INIS)

    Tracy E. Stover Jr.

    2007-01-01

    This work examines uncertainties in the back end fuel cycle metrics of isotopic composition, decay heat, radioactivity, and radiotoxicity. Most advanced fuel cycle scenarios, including the ones represented in this work, are limited by one or more of these metrics, so that quantification of them becomes of great importance in order to optimize or select one of these scenarios. Uncertainty quantification, in this work, is performed by propagating cross-section covariance data, and later number density covariance data, through a reactor physics and depletion code sequence. Propagation of uncertainty is performed primarily via the Efficient Subspace Method (ESM). ESM decomposes the covariance data into singular pairs and perturbs input data along independent directions of the uncertainty and only for the most significant values of that uncertainty. Results of these perturbations being collected, ESM directly calculates the covariance of the observed output posteriori. By exploiting the rank deficient nature of the uncertainty data, ESM works more efficiently than traditional stochastic sampling, but is shown to produce equivalent results. ESM is beneficial for very detailed models with large amounts of input data that make stochastic sampling impractical. In this study various fuel cycle scenarios are examined. Simplified, representative models of pressurized water reactor (PWR) and boiling water reactor (BWR) fuels composed of both uranium oxide and mixed oxides are examined. These simple models are intended to give a representation of the uncertainty that can be associated with open uranium oxide fuel cycles and closed mixed oxide fuel cycles. The simplified models also serve as a demonstration to show that ESM and stochastic sampling produce equivalent results, because these models require minimum computer resources and have amounts of input data small enough such that either method can be quickly implemented and a numerical experiment performed. The simplified

  19. VMTL: a language for end-user model transformation

    DEFF Research Database (Denmark)

    Acretoaie, Vlad; Störrle, Harald; Strüber, Daniel

    2016-01-01

    , these languages are largely ill-equipped for adoption by end-user modelers in areas such as requirements engineering, business process management, or enterprise architecture. We aim to introduce a model transformation language addressing the skills and requirements of end-user modelers. With this contribution, we......Model transformation is a key enabling technology of Model-Driven Engineering (MDE). Existing model transformation languages are shaped by and for MDE practitioners—a user group with needs and capabilities which are not necessarily characteristic of modelers in general. Consequently...... hope to broaden the application scope of model transformation and MDE technology in general. We discuss the profile of end-user modelers and propose a set of design guidelines for model transformation languages addressing them. We then introduce Visual Model Transformation Language (VMTL) following...

  20. Model Manipulation for End-User Modelers

    DEFF Research Database (Denmark)

    Acretoaie, Vlad

    , and transformations using their modeling notation and editor of choice. The VM* languages are implemented via a single execution engine, the VM* Runtime, built on top of the Henshin graph-based transformation engine. This approach combines the benefits of flexibility, maturity, and formality. To simplify model editor......End-user modelers are domain experts who create and use models as part of their work. They are typically not Software Engineers, and have little or no programming and meta-modeling experience. However, using model manipulation languages developed in the context of Model-Driven Engineering often...... requires such experience. These languages are therefore only used by a small subset of the modelers that could, in theory, benefit from them. The goals of this thesis are to substantiate this observation, introduce the concepts and tools required to overcome it, and provide empirical evidence in support...

  1. Screening California Current fishery management scenarios using the Atlantis end-to-end ecosystem model

    Science.gov (United States)

    Kaplan, Isaac C.; Horne, Peter J.; Levin, Phillip S.

    2012-09-01

    End-to-end marine ecosystem models link climate and oceanography to the food web and human activities. These models can be used as forecasting tools, to strategically evaluate management options and to support ecosystem-based management. Here we report the results of such forecasts in the California Current, using an Atlantis end-to-end model. We worked collaboratively with fishery managers at NOAA’s regional offices and staff at the National Marine Sanctuaries (NMS) to explore the impact of fishery policies on management objectives at different spatial scales, from single Marine Sanctuaries to the entire Northern California Current. In addition to examining Status Quo management, we explored the consequences of several gear switching and spatial management scenarios. Of the scenarios that involved large scale management changes, no single scenario maximized all performance metrics. Any policy choice would involve trade-offs between stakeholder groups and policy goals. For example, a coast-wide 25% gear shift from trawl to pot or longline appeared to be one possible compromise between an increase in spatial management (which sacrificed revenue) and scenarios such as the one consolidating bottom impacts to deeper areas (which did not perform substantially differently from Status Quo). Judged on a coast-wide scale, most of the scenarios that involved minor or local management changes (e.g. within Monterey Bay NMS only) yielded results similar to Status Quo. When impacts did occur in these cases, they often involved local interactions that were difficult to predict a priori based solely on fishing patterns. However, judged on the local scale, deviation from Status Quo did emerge, particularly for metrics related to stationary species or variables (i.e. habitat and local metrics of landed value or bycatch). We also found that isolated management actions within Monterey Bay NMS would cause local fishers to pay a cost for conservation, in terms of reductions in landed

  2. Modelling assessment of End Pit Lakes meromictic potential

    International Nuclear Information System (INIS)

    2006-11-01

    The use of End Pit Lakes have been proposed as a remediation solution for oil sands reclamation and operational waters. This report modelled the main factors controlling the occurrence of stratification in Pit Lakes in order to establish design and management guidelines for the Cumulative Environmental Management Association's End Pit Lake Sub-group. The study focused on End Pit Lake size, depth, starting lake salinity concentrations, inflow rates and inflow salinity flux, and investigated their influence on density gradients. One-dimensional modelling and limited 2-D modelling simulations were conducted to examine meromictic potential for a large range of End Pit Lake configurations and conditions. Modelling results showed that fall is the governing season for determining meromixis. The expelling of salt from saline water upon ice formation and its effect on stratification potential and the effect of fresh water loading on stratification potential during spring melt events were not observed to be dominant factors governing meromictic potential for the scenarios examined in the study. Results suggested that shallow End Pit Lakes showed a high turn-over rate with seasonal heating and cooling cycles. Moderately deep End Pit Lakes demonstrated a meromictic potential that was inversely proportional to lake size and require higher starting salinities. With a 2 or 10 million m 3 /yr inflow rate and a 5 parts per thousand starting salinity, a 50 m deep End Pit Lake achieved meromixis at all 3 size ranges considered in the study. Results also showed that the rate of influent salinity decrease was the least important of the parameters influencing meromixis. It was observed that meromixis was a temporary condition in all of the End Pit Lake scenarios envisioned due to the lack of a constant, positive salt replenishment over the long term. It was concluded that further 3-D modelling is required to represent littoral areas as well as to account for extreme winter conditions. A

  3. Physical oceanography - Developing end-to-end models of the California Current Large Marine Ecosystem

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The purpose of this project is to develop spatially discrete end-to-end models of the California Current LME, linking oceanography, biogeochemistry, food web...

  4. Influence of suture technique and suture material selection on the mechanics of end-to-end and end-to-side anastomoses.

    Science.gov (United States)

    Baumgartner, N; Dobrin, P B; Morasch, M; Dong, Q S; Mrkvicka, R

    1996-05-01

    Experiments were performed in dogs to evaluate the mechanics of 26 end-to-end and 42 end-to-side artery-vein graft anastomoses constructed with continuous polypropylene sutures (Surgilene; Davis & Geck, Division of American Cyanamid Co., Danbury, Conn.), continuous polybutester sutures (Novafil; Davis & Geck), and interrupted stitches with either suture material. After construction, the grafts and adjoining arteries were excised, mounted in vitro at in situ length, filled with a dilute barium sulfate suspension, and pressurized in 25 mm Hg steps up to 200 mm Hg. Radiographs were obtained at each pressure. The computed cross-sectional areas of the anastomoses were compared with those of the native arteries at corresponding pressures. Results showed that for the end-to-end anastomoses at 100 mm Hg the cross-sectional areas of the continuous Surgilene anastomoses were 70% of the native artery cross-sectional areas, the cross-sectional areas of the continuous Novafil anastomoses were 90% of the native artery cross-sectional areas, and the cross-sectional areas of the interrupted anastomoses were 107% of the native artery cross-sectional areas (p anastomoses demonstrated no differences in cross-sectional areas or compliance for the three suture techniques. This suggests that, unlike with end-to-end anastomoses, when constructing an end-to-side anastomosis in patients any of the three suture techniques may be acceptable.

  5. An end-to-end coupled model ROMS-N 2 P 2 Z 2 D 2 -OSMOSE of ...

    African Journals Online (AJOL)

    An end-to-end coupled model ROMS-N 2 P 2 Z 2 D 2 -OSMOSE of the southern Benguela foodweb: parameterisation, calibration and pattern-oriented validation. ... We also highlight the capacity of this model for tracking indicators at various hierarchical levels. Keywords: individual-based model, model validation, ...

  6. Study of influence of radial matcher section end shape on RFQ cavity frequency

    International Nuclear Information System (INIS)

    Zhang Zhouli; He Yuan; Zhang Bin; Shi Aimin; Pan Gang; Du Xiaonan; Sun Liepeng; Li Derun

    2014-01-01

    To investigate the feasibility of using a form cutter to machine the Radial Matcher Section (RMS) of the Radio Frequency Quadrupole (RFQ) for the Accelerator Driven System (ADS) project at Institute of Modern Physics, Chinese Academy of Sciences (IMP, CAS), the influence of RMS end shape on the RFQ cavity frequency is studied. The results indicate that using a form cutter to machine the RMS of an RFQ will indeed influence the cavity frequency. The RMS end shape will give more influence to a shorter RFQ cavity. For the 4.2 m ADS RFQ, the influence is negligible, which means that a form cutter can be used to machine the RMS. (authors)

  7. End to end distribution functions for a class of polymer models

    International Nuclear Information System (INIS)

    Khandekar, D.C.; Wiegel, F.W.

    1988-01-01

    The two point end-to-end distribution functions for a class of polymer models have been obtained within the first cumulant approximation. The trial distribution function this purpose is chosen to correspond to a general non-local quadratic functional. An Exact expression for the trial distribution function is obtained. It is pointed out that these trial distribution functions themselves can be used to study certain aspects of the configurational behaviours of polymers. These distribution functions are also used to obtain the averaged mean square size 2 > of a polymer characterized by the non-local quadratic potential energy functional. Finally, we derive an analytic expression for 2 > of a polyelectrolyte model and show that for a long polymer a weak electrostatic interaction does not change the behaviour of 2 > from that of a free polymer. (author). 16 refs

  8. Design and end-to-end modelling of a deployable telescope

    Science.gov (United States)

    Dolkens, Dennis; Kuiper, Hans

    2017-09-01

    a closed-loop system based on measurements of the image sharpness as well as measurements obtained with edge sensors placed between the mirror segments. In addition, a phase diversity system will be used to recover residual wavefront aberrations. To aid the design of the deployable telescope, an end-to-end performance model was developed. The model is built around a dedicated ray-trace program written in Matlab. This program was built from the ground up for the purpose of modelling segmented telescope systems and allows for surface data computed with Finite Element Models (FEM) to be imported in the model. The program also contains modules which can simulate the closed-loop calibration of the telescope and it can use simulated images as an input for phase diversity and image processing algorithms. For a given thermo-mechanical state, the end-to-end model can predict the image quality that will be obtained after the calibration has been completed and the image has been processed. As such, the model is a powerful systems engineering tool, which can be used to optimize the in-orbit performance of a segmented, deployable telescope.

  9. End-to-End Traffic Flow Modeling of the Integrated SCaN Network

    Science.gov (United States)

    Cheung, K.-M.; Abraham, D. S.

    2012-05-01

    In this article, we describe the analysis and simulation effort of the end-to-end traffic flow for the Integrated Space Communications and Navigation (SCaN) Network. Using the network traffic derived for the 30-day period of July 2018 from the Space Communications Mission Model (SCMM), we generate the wide-area network (WAN) bandwidths of the ground links for different architecture options of the Integrated SCaN Network. We also develop a new analytical scheme to model the traffic flow and buffering mechanism of a store-and-forward network. It is found that the WAN bandwidth of the Integrated SCaN Network is an important differentiator of different architecture options, as the recurring circuit costs of certain architecture options can be prohibitively high.

  10. Clamped end conditions and cross section deformation in the finite element absolute nodal coordinate formulation

    International Nuclear Information System (INIS)

    Hussein, Bassam A.; Weed, David; Shabana, Ahmed A.

    2009-01-01

    In the finite element absolute nodal coordinate formulation (ANCF), the elimination of the relative translations and rotations at a point does not necessarily define a fully clamped joint, particularly in the case of fully parameterized ANCF finite elements that allow for the deformation of the cross section. In this investigation, the formulations and results of two different sets of clamped end conditions that define two different joints are compared. The first joint, called the partially clamped joint, eliminates only the translations and rotations at a point on the cross section. The second joint, called the fully clamped joint, eliminates all the translation, rotation and deformation degrees of freedom at a point on the cross section. The kinematic equations that define the partially and fully clamped joints are developed, and the dynamic equations used in the comparative numerical study presented in this paper are shown. As discussed in this investigation, the fully clamped joint does not allow for the deformation of the cross section at the joint node since the gradient vectors remain orthogonal unit vectors. The partially clamped joint, on the other hand, allows for the deformation of the cross section. Nanson's formula is used as a measure of the deformation of the cross section in the case of the partially clamped joint. A very flexible pendulum that has a rigid body attached to its free end is used to compare the results of the partially and fully clamped joints. The numerical results obtained using this very flexible pendulum example show that, while the type of joint (partially or fully clamped) does not significantly affect the gross reference motion of the system, there are fundamental differences between the two joints since the partially clamped joint allows for the cross section deformations at the joint node

  11. An End-to-End Model of Plant Pheromone Channel for Long Range Molecular Communication.

    Science.gov (United States)

    Unluturk, Bige D; Akyildiz, Ian F

    2017-01-01

    A new track in molecular communication is using pheromones which can scale up the range of diffusion-based communication from μm meters to meters and enable new applications requiring long range. Pheromone communication is the emission of molecules in the air which trigger behavioral or physiological responses in receiving organisms. The objective of this paper is to introduce a new end-to-end model which incorporates pheromone behavior with communication theory for plants. The proposed model includes both the transmission and reception processes as well as the propagation channel. The transmission process is the emission of pheromones from the leaves of plants. The dispersion of pheromones by the flow of wind constitutes the propagation process. The reception process is the sensing of pheromones by the pheromone receptors of plants. The major difference of pheromone communication from other molecular communication techniques is the dispersion channel acting under the laws of turbulent diffusion. In this paper, the pheromone channel is modeled as a Gaussian puff, i.e., a cloud of pheromone released instantaneously from the source whose dispersion follows a Gaussian distribution. Numerical results on the performance of the overall end-to-end pheromone channel in terms of normalized gain and delay are provided.

  12. Modeling hard clinical end-point data in economic analyses.

    Science.gov (United States)

    Kansal, Anuraag R; Zheng, Ying; Palencia, Roberto; Ruffolo, Antonio; Hass, Bastian; Sorensen, Sonja V

    2013-11-01

    The availability of hard clinical end-point data, such as that on cardiovascular (CV) events among patients with type 2 diabetes mellitus, is increasing, and as a result there is growing interest in using hard end-point data of this type in economic analyses. This study investigated published approaches for modeling hard end-points from clinical trials and evaluated their applicability in health economic models with different disease features. A review of cost-effectiveness models of interventions in clinically significant therapeutic areas (CV diseases, cancer, and chronic lower respiratory diseases) was conducted in PubMed and Embase using a defined search strategy. Only studies integrating hard end-point data from randomized clinical trials were considered. For each study included, clinical input characteristics and modeling approach were summarized and evaluated. A total of 33 articles (23 CV, eight cancer, two respiratory) were accepted for detailed analysis. Decision trees, Markov models, discrete event simulations, and hybrids were used. Event rates were incorporated either as constant rates, time-dependent risks, or risk equations based on patient characteristics. Risks dependent on time and/or patient characteristics were used where major event rates were >1%/year in models with fewer health states (Models of infrequent events or with numerous health states generally preferred constant event rates. The detailed modeling information and terminology varied, sometimes requiring interpretation. Key considerations for cost-effectiveness models incorporating hard end-point data include the frequency and characteristics of the relevant clinical events and how the trial data is reported. When event risk is low, simplification of both the model structure and event rate modeling is recommended. When event risk is common, such as in high risk populations, more detailed modeling approaches, including individual simulations or explicitly time-dependent event rates, are

  13. End-to-end models for marine ecosystems: Are we on the precipice of a significant advance or just putting lipstick on a pig?

    Directory of Open Access Journals (Sweden)

    Kenneth A. Rose

    2012-02-01

    Full Text Available There has been a rapid rise in the development of end-to-end models for marine ecosystems over the past decade. Some reasons for this rise include need for predicting effects of climate change on biota and dissatisfaction with existing models. While the benefits of a well-implemented end-to-end model are straightforward, there are many challenges. In the short term, my view is that the major role of end-to-end models is to push the modelling community forward, and to identify critical data so that these data can be collected now and thus be available for the next generation of end-to-end models. I think we should emulate physicists and build theoretically-oriented models first, and then collect the data. In the long-term, end-to-end models will increase their skill, data collection will catch up, and end-to-end models will move towards site-specific applications with forecasting and management capabilities. One pathway into the future is individual efforts, over-promise, and repackaging of poorly performing component submodels (“lipstick on a pig”. The other pathway is a community-based collaborative effort, with appropriate caution and thoughtfulness, so that the needed improvements are achieved (“significant advance”. The promise of end-to-end modelling is great. We should act now to avoid missing a great opportunity.

  14. Results of 3-dimensional structural FE-modeling of the coil end-regions of the LHC main dipoles

    CERN Document Server

    Hoeck, U; Schillo, M; Perini, D; Siegel, N

    2000-01-01

    The transition region between the straight part and the ends of the coils of the LHC model and prototype dipole magnets are often identified as the origin of training quenches. In order to study how the discontinuities in the material properties of these regions affect coil pre-stress and possibly gain more insight in the quench behavior, a program was set up at CERN to analyze by 3D-FEM these particular regions. The ACCEL team, who performed a similar analysis for the main quadrupoles of the Superconducting Supercollider SSC, is entrusted with this program. In this paper we report on the results of 3D-modeling and analysis of the coil return end region, including the complete coil mass, of a 1-m single bore model magnet. This magnet represents all relevant features of the "two-in-one" LHC main dipole design concerning the winding configuration, the collar pack, the yoke, and the outer shell representing the He-vessel. The transition region between coil ends and straight section is modeled by slicing the magn...

  15. End-to-end Information Flow Security Model for Software-Defined Networks

    Directory of Open Access Journals (Sweden)

    D. Ju. Chaly

    2015-01-01

    Full Text Available Software-defined networks (SDN are a novel paradigm of networking which became an enabler technology for many modern applications such as network virtualization, policy-based access control and many others. Software can provide flexibility and fast-paced innovations in the networking; however, it has a complex nature. In this connection there is an increasing necessity of means for assuring its correctness and security. Abstract models for SDN can tackle these challenges. This paper addresses to confidentiality and some integrity properties of SDNs. These are critical properties for multi-tenant SDN environments, since the network management software must ensure that no confidential data of one tenant are leaked to other tenants in spite of using the same physical infrastructure. We define a notion of end-to-end security in context of software-defined networks and propose a semantic model where the reasoning is possible about confidentiality, and we can check that confidential information flows do not interfere with non-confidential ones. We show that the model can be extended in order to reason about networks with secure and insecure links which can arise, for example, in wireless environments.The article is published in the authors’ wording.

  16. ONE SIZE DOES NOT FIT ALL — UNDERSTANDING THE FRONT-END AND BACK-END OF BUSINESS MODEL INNOVATION

    OpenAIRE

    FRANZISKA GÜNZEL; ANNA B. HOLM

    2013-01-01

    Business model innovation is becoming a central research topic in management. However, a lack of a common understanding of the nature of the business model leads to disregarding its multifaceted structure when analyzing the business model innovation process. This article proposes a more detailed understanding of the business model innovation process by drawing on existing knowledge from new product development literature and examining the front-end and the back-end of business model innovatio...

  17. Network modeling for reverse flows of end-of-life vehicles

    International Nuclear Information System (INIS)

    Ene, Seval; Öztürk, Nursel

    2015-01-01

    Highlights: • We developed a network model for reverse flows of end-of-life vehicles. • The model considers all recovery operations for end-of-life vehicles. • A scenario-based model is used for uncertainty to improve real case applications. • The model is adequate to real case applications for end-of-life vehicles recovery. • Considerable insights are gained from the model by sensitivity analyses. - Abstract: Product recovery operations are of critical importance for the automotive industry in complying with environmental regulations concerning end-of-life products management. Manufacturers must take responsibility for their products over the entire life cycle. In this context, there is a need for network design methods for effectively managing recovery operations and waste. The purpose of this study is to develop a mathematical programming model for managing reverse flows in end-of-life vehicles’ recovery network. A reverse flow is the collection of used products from consumers and the transportation of these products for the purpose of recycling, reuse or disposal. The proposed model includes all operations in a product recovery and waste management network for used vehicles and reuse for vehicle parts such as collection, disassembly, refurbishing, processing (shredding), recycling, disposal and reuse of vehicle parts. The scope of the network model is to determine the numbers and locations of facilities in the network and the material flows between these facilities. The results show the performance of the model and its applicability for use in the planning of recovery operations in the automotive industry. The main objective of recovery and waste management is to maximize revenue and minimize pollution in end-of-life product operations. This study shows that with an accurate model, these activities may provide economic benefits and incentives in addition to protecting the environment

  18. Network modeling for reverse flows of end-of-life vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Ene, Seval; Öztürk, Nursel

    2015-04-15

    Highlights: • We developed a network model for reverse flows of end-of-life vehicles. • The model considers all recovery operations for end-of-life vehicles. • A scenario-based model is used for uncertainty to improve real case applications. • The model is adequate to real case applications for end-of-life vehicles recovery. • Considerable insights are gained from the model by sensitivity analyses. - Abstract: Product recovery operations are of critical importance for the automotive industry in complying with environmental regulations concerning end-of-life products management. Manufacturers must take responsibility for their products over the entire life cycle. In this context, there is a need for network design methods for effectively managing recovery operations and waste. The purpose of this study is to develop a mathematical programming model for managing reverse flows in end-of-life vehicles’ recovery network. A reverse flow is the collection of used products from consumers and the transportation of these products for the purpose of recycling, reuse or disposal. The proposed model includes all operations in a product recovery and waste management network for used vehicles and reuse for vehicle parts such as collection, disassembly, refurbishing, processing (shredding), recycling, disposal and reuse of vehicle parts. The scope of the network model is to determine the numbers and locations of facilities in the network and the material flows between these facilities. The results show the performance of the model and its applicability for use in the planning of recovery operations in the automotive industry. The main objective of recovery and waste management is to maximize revenue and minimize pollution in end-of-life product operations. This study shows that with an accurate model, these activities may provide economic benefits and incentives in addition to protecting the environment.

  19. A Computational Analysis Model for Open-ended Cognitions

    Science.gov (United States)

    Morita, Junya; Miwa, Kazuhisa

    In this paper, we propose a novel usage for computational cognitive models. In cognitive science, computational models have played a critical role of theories for human cognitions. Many computational models have simulated results of controlled psychological experiments successfully. However, there have been only a few attempts to apply the models to complex realistic phenomena. We call such a situation ``open-ended situation''. In this study, MAC/FAC (``many are called, but few are chosen''), proposed by [Forbus 95], that models two stages of analogical reasoning was applied to our open-ended psychological experiment. In our experiment, subjects were presented a cue story, and retrieved cases that had been learned in their everyday life. Following this, they rated inferential soundness (goodness as analogy) of each retrieved case. For each retrieved case, we computed two kinds of similarity scores (content vectors/structural evaluation scores) using the algorithms of the MAC/FAC. As a result, the computed content vectors explained the overall retrieval of cases well, whereas the structural evaluation scores had a strong relation to the rated scores. These results support the MAC/FAC's theoretical assumption - different similarities are involved on the two stages of analogical reasoning. Our study is an attempt to use a computational model as an analysis device for open-ended human cognitions.

  20. Modeling, simulation, and optimization of a front-end system for acetylene hydrogenation reactors

    Directory of Open Access Journals (Sweden)

    R. Gobbo

    2004-12-01

    Full Text Available The modeling, simulation, and dynamic optimization of an industrial reaction system for acetylene hydrogenation are discussed in the present work. The process consists of three adiabatic fixed-bed reactors, in series, with interstage cooling. These reactors are located after the compression and the caustic scrubbing sections of an ethylene plant, characterizing a front-end system; in contrast to the tail-end system where the reactors are placed after the de-ethanizer unit. The acetylene conversion and selectivity profiles for the reactors are optimized, taking into account catalyst deactivation and process constraints. A dynamic optimal temperature profile that maximizes ethylene production and meets product specifications is obtained by controlling the feed and intercoolers temperatures. An industrial acetylene hydrogenation system is used to provide the necessary data to adjust kinetics and transport parameters and to validate the approach.

  1. Open-end tube dynamic flow model with an oscillatory extortion

    Directory of Open Access Journals (Sweden)

    Tulwin Tytus

    2017-01-01

    Full Text Available This paper presents a derivation of dynamic 2d mathematical model for open end tube with oscillatory extortion in the region of the closed end. The aim the research is to investigate possible uses of the increased pressure in the enclosed tube chamber, especially for energy efficient lift generation. The mathematical model allows to test and predict how flow modifications impact the resultant lifting force. A derivation of the proposed mathematical model is shown. The mathematical model is then compared to the computational fluid dynamics discrete model. The results prove the accuracy of the mathematical physical model.

  2. End-of-life care in general practice: A cross-sectional, retrospective survey of 'cancer', 'organ failure' and 'old-age/dementia' patients

    NARCIS (Netherlands)

    Evans, N.C.; Pasman, H.R.W.; Donker, G.A.; Deliens, L.; Block, L.; Onwuteaka-Philipsen, B.D.

    2014-01-01

    Background: End-of-life care is often provided in primary care settings. Aim: To describe and compare general-practitioner end-of-life care for Dutch patients who died from 'cancer', 'organ failure' and 'old-age or dementia'. Design: A cross-sectional, retrospective survey was conducted within a

  3. Model of a generator end-winding cage

    International Nuclear Information System (INIS)

    Leger, A.C.; Fanton, J.P.; Davies, C.

    1994-09-01

    This document presents some studies concerning the vibratory characterization of particular structures called: generator end-winding cages. These structures are mainly made up of the endings of armature windings. The question of their good mechanical behaviour is of prime importance, since they are submitted to high electromagnetic efforts during the different electrical ratings encountered during operation. The designer (GEC-Alsthom) and the user (EDF) have both undertaken numerical calculations in order to characterize a given machine, in this case a 600 MW bipolar generator; it appeared interesting to compare such calculations. The models realized respectively by GEC-Alsthom and EDF make use of different techniques and hypotheses. GEC-Alsthom represents the sets of rods and spacers by plates, which properties are determined by a pre-processor. The model is simplified to take into account the existing symmetries. It takes profit of previous experience and aims at a fast utilisation. The EDF model tends to allow a further comprehensive calculation, form the electromagnetic efforts to the determination of local stresses. The whole set of the constituting elements of the structure is modelled by beams, which leads to an important size for the model (21 000 degrees of freedom). The validation performed on the two models has been focused on the comparison between respective results and also with experimental results. Each model provides values for the first eigenfrequencies and the associated modes shapes. (authors). 3 refs., 3 figs., 2 tabs

  4. Modelling axisymmetric cod-ends made of different mesh types

    DEFF Research Database (Denmark)

    Priour, D.; Herrmann, Bent; O'Neill, F.G.

    2009-01-01

    the selectivity process has become more important. This paper presents a model of the deformation of an axisymmetric cod-end. The twine tension and the catch pressure acting on the knots of each mesh along the cod-end profile are calculated, and a Newton-Raphson scheme is used to estimate the equilibrium position...

  5. A calibrated energy end-use model for the U.S. chemical industry

    International Nuclear Information System (INIS)

    Ozalp, N.; Hyman, B.

    2005-01-01

    The chemical industry is the second largest energy user after the petroleum industry in the United States. This paper provided a model for onsite steam and power generation in the chemical industry, as well as an end-use of the industrial gas manufacturing sector. The onsite steam and power generation model included the actual conversion efficiencies of prime movers in the sector. The energy end-use model also allocated combustible fuel and renewable energy inputs among generic end-uses including intermediate conversions through onsite power and steam generation. The model was presented in the form of a graphical depiction of energy flows. Results indicate that 35 per cent of the energy output from boilers is used for power generation, whereas 45 per cent goes directly to end-uses and 20 per cent to waste heat tanks for recovery in the chemical industry. The end-use model for the industrial gas manufacturing sector revealed that 42 per cent of the fuel input goes to onsite steam and power generation, whereas 58 per cent goes directly to end-uses. Among the end-uses, machine drive was the biggest energy user. It was suggested that the model is applicable to all other industries and is consistent with U.S. Department of Energy data for 1998. When used in conjunction with similar models for other years, it can be used to identify changes and trends in energy utilization at the prime mover level of detail. An analysis of the economic impact of energy losses can be based on the results of this model. Cascading of waste heat from high temperature processes to low temperature processes could be integrated into the model. 20 refs., 4 tabs., 8 figs

  6. Model cross section calculations using LAHET

    International Nuclear Information System (INIS)

    Prael, R.E.

    1992-01-01

    The current status of LAHET is discussed. The effect of a multistage preequilibrium exciton model following the INC is examined for neutron emission benchmark calculations, as is the use of a Fermi breakup model for light nuclei rather than an evaporation model. Comparisons are made also for recent fission cross section experiments, and a discussion of helium production cross sections is presented

  7. Nurses' knowledge of advance directives and perceived confidence in end-of-life care: a cross-sectional study in five countries.

    LENUS (Irish Health Repository)

    Coffey, Alice

    2016-01-28

    Nurses\\' knowledge regarding advance directives may affect their administration and completion in end-of-life care. Confidence among nurses is a barrier to the provision of quality end-of-life care. This study investigated nurses\\' knowledge of advance directives and perceived confidence in end-of-life care, in Hong Kong, Ireland, Israel, Italy and the USA using a cross-sectional descriptive design (n = 1089). In all countries, older nurses and those who had more professional experience felt more confident managing patients\\' symptoms at end-of-life and more comfortable stopping preventive medications at end-of-life. Nurses in the USA reported that they have more knowledge and experience of advance directives compared with other countries. In addition, they reported the highest levels of confidence and comfort in dealing with end-of-life care. Although legislation for advance directives does not yet exist in Ireland, nurses reported high levels of confidence in end-of-life care.

  8. End-of-Discharge and End-of-Life Prediction in Lithium-Ion Batteries with Electrochemistry-Based Aging Models

    Science.gov (United States)

    Daigle, Matthew; Kulkarni, Chetan S.

    2016-01-01

    As batteries become increasingly prevalent in complex systems such as aircraft and electric cars, monitoring and predicting battery state of charge and state of health becomes critical. In order to accurately predict the remaining battery power to support system operations for informed operational decision-making, age-dependent changes in dynamics must be accounted for. Using an electrochemistry-based model, we investigate how key parameters of the battery change as aging occurs, and develop models to describe aging through these key parameters. Using these models, we demonstrate how we can (i) accurately predict end-of-discharge for aged batteries, and (ii) predict the end-of-life of a battery as a function of anticipated usage. The approach is validated through an experimental set of randomized discharge profiles.

  9. Optimized capture section for a muon accelerator front end

    Directory of Open Access Journals (Sweden)

    Hisham Kamal Sayed

    2014-07-01

    Full Text Available In a muon accelerator complex, a target is bombarded by a multi-MW proton beam to produce pions, which decay into the muons which are thereafter bunched, cooled, and accelerated. The front end of the complex captures those pions, then manipulates their phase space, and that of the muons into which they decay, to maximize the number of muons within the acceptance of the downstream systems. The secondary pion beam produced at the target is captured by a high field target solenoid that tapers down to a constant field throughout the rest of the front end. In this study we enhance the useful muon flux by introducing a new design of the longitudinal profile of the solenoid field at, and downstream of, the target. We find that the useful muon flux exiting the front end is larger when the field at the target is higher, the distance over which the field tapers down is shorter, and the field at the end of the taper is higher. We describe how the solenoid field profile impacts the transverse and longitudinal phase space of the beam and thereby leads to these dependencies.

  10. Experimental research on end-to-side anastomosis of peripheral nerves and effect of FK506 on end-to-side anastomosis.

    Science.gov (United States)

    Yang, L M; Wu, Y X; Zhang, X P; Li, X H

    2014-01-01

    To study the effects of end-to-side anastomosis of initially-denatured nerves at different times. 60 male Wistar albino rats were used to fabricate animal models for the experiment on end-to-side anastomosis of peripheral nerves and 50 female Wistar albino rats were used to fabricate animal models for the experiment on the effect of FK506 on end-to-side anastomosis. Bilateral common peroneal nerve, tibialis anterior muscle electrophysiological and histological examinations, tibialis anterior muscle wet muscle weight determination, and motor end plate examination were performed 3 months after operation. All recovery rates of action potential, single muscle contraction force and tetanic contraction force of the FK506 experimental group are significantly higher than those of the control group and the sectional area of muscle fiber is also higher than that of the control group of normal saline. The best time for end-to-side anastomosis of nerves should be controlled within 2 weeks and the effect of end-to-side anastomosis of nerves will gradually become unsatisfactory. FK506 plays a role in promoting functional rehabilitation following nerve end-to-side anastomosis (Tab. 7, Fig. 4, Ref. 31).

  11. West Coast fish, mammal, and bird species diets - Developing end-to-end models of the California Current Large Marine Ecosystem

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The purpose of this project is to develop spatially discrete end-to-end models of the California Current LME, linking oceanography, biogeochemistry, food web...

  12. Analytical Model for the End-Bearing Capacity of Tapered Piles Using Cavity Expansion Theory

    Directory of Open Access Journals (Sweden)

    Suman Manandhar

    2012-01-01

    Full Text Available On the basis of evidence from model tests on increasing the end-bearing behavior of tapered piles at the load-settlement curve, this paper proposes an analytical spherical cavity expansion theory to evaluate the end-bearing capacity. The angle of tapering is inserted in the proposed model to evaluate the end-bearing capacity. The test results of the proposed model in different types of sands and different relative densities show good effects compared to conventional straight piles. The end-bearing capacity increases with increases in the tapering angle. The paper then propounds a model for prototypes and real-type pile tests which predicts and validates to evaluate the end-bearing capacity.

  13. A THEORETICAL MODEL OF SUPPORTING OPEN SOURCE FRONT END INNOVATION THROUGH IDEA MANAGEMENT

    DEFF Research Database (Denmark)

    Aagaard, Annabeth

    2013-01-01

    to overcome these various challenges companies are looking for new models to support FEI. This theoretical paper explores in what way idea management may be applied as a tool in facilitation of front end innovation and how this facilitation may be captured in a conceptual model. First, I show through...... a literature study, how idea management and front end innovation are related and how they may support each other. Secondly, I present a theoretical model of how idea management may be applied in support of the open source front end of new product innovations. Thirdly, I present different venues of further...... exploration of active facilitation of open source front end innovation through idea management....

  14. ROXIE the Routine for the Optimization of Magnet X-sections, Inverse Field Computation and Coil End Design

    CERN Document Server

    Russenschuck, Stephan

    1999-01-01

    The ROXIE software program package has been developed for the design of the superconducting magnets for the LHC at CERN. The software is used as an approach towards the integrated design of superconducting magnets including feature-based coil geometry creation, conceptual design using genetic algorithms, optimization of the coil and iron cross-sections using a reduced vector-potential formulation, 3-D coil end geometry and field optimization using deterministic vector- optimization techniques, tolerance analysis, production of drawings by means of a DXF interface, end-spacer design with interfaces to CAD-CAM for the CNC machining of these pieces, and the tracing of manufacturing errors using field quality measurements. This paper gives an overview of the methods applied in the ROXIE program. (9 refs).

  15. Standardizing an End-to-end Accounting Service

    Science.gov (United States)

    Greenberg, Edward; Kazz, Greg

    2006-01-01

    Currently there are no space system standards available for space agencies to accomplish end-to-end accounting. Such a standard does not exist for spacecraft operations nor for tracing the relationship between the mission planning activities, the command sequences designed to perform those activities, the commands formulated to initiate those activities and the mission data and specifically the mission data products created by those activities. In order for space agencies to cross-support one another for data accountability/data tracing and for inter agency spacecraft to interoperate with each other, an international CCSDS standard for end-to-end data accountability/tracing needs to be developed. We will first describe the end-to-end accounting service model and functionality that supports the service. This model will describe how science plans that are ultimately transformed into commands can be associated with the telemetry products generated as a result of their execution. Moreover, the interaction between end-to-end accounting and service management will be explored. Finally, we will show how the standard end-to-end accounting service can be applied to a real life flight project i.e., the Mars Reconnaissance Orbiter project.

  16. Network modeling for reverse flows of end-of-life vehicles.

    Science.gov (United States)

    Ene, Seval; Öztürk, Nursel

    2015-04-01

    Product recovery operations are of critical importance for the automotive industry in complying with environmental regulations concerning end-of-life products management. Manufacturers must take responsibility for their products over the entire life cycle. In this context, there is a need for network design methods for effectively managing recovery operations and waste. The purpose of this study is to develop a mathematical programming model for managing reverse flows in end-of-life vehicles' recovery network. A reverse flow is the collection of used products from consumers and the transportation of these products for the purpose of recycling, reuse or disposal. The proposed model includes all operations in a product recovery and waste management network for used vehicles and reuse for vehicle parts such as collection, disassembly, refurbishing, processing (shredding), recycling, disposal and reuse of vehicle parts. The scope of the network model is to determine the numbers and locations of facilities in the network and the material flows between these facilities. The results show the performance of the model and its applicability for use in the planning of recovery operations in the automotive industry. The main objective of recovery and waste management is to maximize revenue and minimize pollution in end-of-life product operations. This study shows that with an accurate model, these activities may provide economic benefits and incentives in addition to protecting the environment. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. End-of-life care in general practice: a cross-sectional, retrospective survey of ‘cancer’, ‘organ failure’ and ‘old-age/dementia’ patients.

    NARCIS (Netherlands)

    Evans, N.; Pasman, H.R.W.; Donker, G.A.; Deliens, L.; Block, L. van den; Onwuteaka-Philipsen, B.

    2014-01-01

    Background: End-of-life care is often provided in primary care settings. Aim: To describe and compare general-practitioner end-of-life care for Dutch patients who died from ‘cancer’, ‘organ failure’ and ‘old-age or dementia’. Design: A cross-sectional, retrospective survey was conducted within a

  18. West Coast fish, mammal, bird life history and abunance parameters - Developing end-to-end models of the California Current Large Marine Ecosystem

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The purpose of this project is to develop spatially discrete end-to-end models of the California Current LME, linking oceanography, biogeochemistry, food web...

  19. Gulf of California species and catch spatial distributions and historical time series - Developing end-to-end models of the Gulf of California

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The purpose of this project is to develop spatially discrete end-to-end models of the northern Gulf of California, linking oceanography, biogeochemistry, food web...

  20. A model-based software development methodology for high-end automotive components

    NARCIS (Netherlands)

    Ravanan, Mahmoud

    2014-01-01

    This report provides a model-based software development methodology for high-end automotive components. The V-model is used as a process model throughout the development of the software platform. It offers a framework that simplifies the relation between requirements, design, implementation,

  1. Team-Based Models for End-of-Life Care: An Evidence-Based Analysis

    Science.gov (United States)

    2014-01-01

    Background End of life refers to the period when people are living with advanced illness that will not stabilize and from which they will not recover and will eventually die. It is not limited to the period immediately before death. Multiple services are required to support people and their families during this time period. The model of care used to deliver these services can affect the quality of the care they receive. Objectives Our objective was to determine whether an optimal team-based model of care exists for service delivery at end of life. In systematically reviewing such models, we considered their core components: team membership, services offered, modes of patient contact, and setting. Data Sources A literature search was performed on October 14, 2013, using Ovid MEDLINE, Ovid MEDLINE In-Process and Other Non-Indexed Citations, Ovid Embase, EBSCO Cumulative Index to Nursing & Allied Health Literature (CINAHL), and EBM Reviews, for studies published from January 1, 2000, to October 14, 2013. Review Methods Abstracts were reviewed by a single reviewer and full-text articles were obtained that met the inclusion criteria. Studies were included if they evaluated a team model of care compared with usual care in an end-of-life adult population. A team was defined as having at least 2 health care disciplines represented. Studies were limited to English publications. A meta-analysis was completed to obtain pooled effect estimates where data permitted. The GRADE quality of the evidence was evaluated. Results Our literature search located 10 randomized controlled trials which, among them, evaluated the following 6 team-based models of care: hospital, direct contact home, direct contact home, indirect contact comprehensive, indirect contact comprehensive, direct contact comprehensive, direct, and early contact Direct contact is when team members see the patient; indirect contact is when they advise another health care practitioner (e.g., a family doctor) who sees

  2. Impacts of the Deepwater Horizon oil spill evaluated using an end-to-end ecosystem model.

    Science.gov (United States)

    Ainsworth, Cameron H; Paris, Claire B; Perlin, Natalie; Dornberger, Lindsey N; Patterson, William F; Chancellor, Emily; Murawski, Steve; Hollander, David; Daly, Kendra; Romero, Isabel C; Coleman, Felicia; Perryman, Holly

    2018-01-01

    We use a spatially explicit biogeochemical end-to-end ecosystem model, Atlantis, to simulate impacts from the Deepwater Horizon oil spill and subsequent recovery of fish guilds. Dose-response relationships with expected oil concentrations were utilized to estimate the impact on fish growth and mortality rates. We also examine the effects of fisheries closures and impacts on recruitment. We validate predictions of the model by comparing population trends and age structure before and after the oil spill with fisheries independent data. The model suggests that recruitment effects and fishery closures had little influence on biomass dynamics. However, at the assumed level of oil concentrations and toxicity, impacts on fish mortality and growth rates were large and commensurate with observations. Sensitivity analysis suggests the biomass of large reef fish decreased by 25% to 50% in areas most affected by the spill, and biomass of large demersal fish decreased even more, by 40% to 70%. Impacts on reef and demersal forage caused starvation mortality in predators and increased reliance on pelagic forage. Impacts on the food web translated effects of the spill far away from the oiled area. Effects on age structure suggest possible delayed impacts on fishery yields. Recovery of high-turnover populations generally is predicted to occur within 10 years, but some slower-growing populations may take 30+ years to fully recover.

  3. End to End Digitisation and Analysis of Three-Dimensional Coral Models, from Communities to Corallites.

    Directory of Open Access Journals (Sweden)

    Luis Gutierrez-Heredia

    Full Text Available Coral reefs hosts nearly 25% of all marine species and provide food sources for half a billion people worldwide while only a very small percentage have been surveyed. Advances in technology and processing along with affordable underwater cameras and Internet availability gives us the possibility to provide tools and softwares to survey entire coral reefs. Holistic ecological analyses of corals require not only the community view (10s to 100s of meters, but also the single colony analysis as well as corallite identification. As corals are three-dimensional, classical approaches to determine percent cover and structural complexity across spatial scales are inefficient, time-consuming and limited to experts. Here we propose an end-to-end approach to estimate these parameters using low-cost equipment (GoPro, Canon and freeware (123D Catch, Meshmixer and Netfabb, allowing every community to participate in surveys and monitoring of their coral ecosystem. We demonstrate our approach on 9 species of underwater colonies in ranging size and morphology. 3D models of underwater colonies, fresh samples and bleached skeletons with high quality texture mapping and detailed topographic morphology were produced, and Surface Area and Volume measurements (parameters widely used for ecological and coral health studies were calculated and analysed. Moreover, we integrated collected sample models with micro-photogrammetry models of individual corallites to aid identification and colony and polyp scale analysis.

  4. End to End Digitisation and Analysis of Three-Dimensional Coral Models, from Communities to Corallites.

    Science.gov (United States)

    Gutierrez-Heredia, Luis; Benzoni, Francesca; Murphy, Emma; Reynaud, Emmanuel G

    2016-01-01

    Coral reefs hosts nearly 25% of all marine species and provide food sources for half a billion people worldwide while only a very small percentage have been surveyed. Advances in technology and processing along with affordable underwater cameras and Internet availability gives us the possibility to provide tools and softwares to survey entire coral reefs. Holistic ecological analyses of corals require not only the community view (10s to 100s of meters), but also the single colony analysis as well as corallite identification. As corals are three-dimensional, classical approaches to determine percent cover and structural complexity across spatial scales are inefficient, time-consuming and limited to experts. Here we propose an end-to-end approach to estimate these parameters using low-cost equipment (GoPro, Canon) and freeware (123D Catch, Meshmixer and Netfabb), allowing every community to participate in surveys and monitoring of their coral ecosystem. We demonstrate our approach on 9 species of underwater colonies in ranging size and morphology. 3D models of underwater colonies, fresh samples and bleached skeletons with high quality texture mapping and detailed topographic morphology were produced, and Surface Area and Volume measurements (parameters widely used for ecological and coral health studies) were calculated and analysed. Moreover, we integrated collected sample models with micro-photogrammetry models of individual corallites to aid identification and colony and polyp scale analysis.

  5. An integrative modeling approach for the efficient estimation of cross sectional tibial stresses during locomotion.

    Science.gov (United States)

    Derrick, Timothy R; Edwards, W Brent; Fellin, Rebecca E; Seay, Joseph F

    2016-02-08

    The purpose of this research was to utilize a series of models to estimate the stress in a cross section of the tibia, located 62% from the proximal end, during walking. Twenty-eight male, active duty soldiers walked on an instrumented treadmill while external force data and kinematics were recorded. A rigid body model was used to estimate joint moments and reaction forces. A musculoskeletal model was used to gather muscle length, muscle velocity, moment arm and orientation information. Optimization procedures were used to estimate muscle forces and finally internal bone forces and moments were applied to an inhomogeneous, subject specific bone model obtained from CT scans to estimate stress in the bone cross section. Validity was assessed by comparison to stresses calculated from strain gage data in the literature and sensitivity was investigated using two simplified versions of the bone model-a homogeneous model and an ellipse approximation. Peak compressive stress occurred on the posterior aspect of the cross section (-47.5 ± 14.9 MPa). Peak tensile stress occurred on the anterior aspect (27.0 ± 11.7 MPa) while the location of peak shear was variable between subjects (7.2 ± 2.4 MPa). Peak compressive, tensile and shear stresses were within 0.52 MPa, 0.36 MPa and 3.02 MPa respectively of those calculated from the converted strain gage data. Peak values from a inhomogeneous model of the bone correlated well with homogeneous model (normal: 0.99; shear: 0.94) as did the normal ellipse model (r=0.89-0.96). However, the relationship between shear stress in the inhomogeneous model and ellipse model was less accurate (r=0.64). The procedures detailed in this paper provide a non-invasive and relatively quick method of estimating cross sectional stress that holds promise for assessing injury and osteogenic stimulus in bone during normal physical activity. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. The Open-Ended Approach Framework

    Science.gov (United States)

    Munroe, Lloyd

    2015-01-01

    This paper describes a pedagogical framework that teachers can use to support students who are engaged in solving open-ended problems, by explaining how two Japanese expert teachers successfully apply open-ended problems in their mathematics class. The Open-Ended Approach (OPA) framework consists of two main sections: Understanding Mathematical…

  7. Models for Pooled Time-Series Cross-Section Data

    Directory of Open Access Journals (Sweden)

    Lawrence E Raffalovich

    2015-07-01

    Full Text Available Several models are available for the analysis of pooled time-series cross-section (TSCS data, defined as “repeated observations on fixed units” (Beck and Katz 1995. In this paper, we run the following models: (1 a completely pooled model, (2 fixed effects models, and (3 multi-level/hierarchical linear models. To illustrate these models, we use a Generalized Least Squares (GLS estimator with cross-section weights and panel-corrected standard errors (with EViews 8 on the cross-national homicide trends data of forty countries from 1950 to 2005, which we source from published research (Messner et al. 2011. We describe and discuss the similarities and differences between the models, and what information each can contribute to help answer substantive research questions. We conclude with a discussion of how the models we present may help to mitigate validity threats inherent in pooled time-series cross-section data analysis.

  8. Mixed integer nonlinear programming model of wireless pricing scheme with QoS attribute of bandwidth and end-to-end delay

    Science.gov (United States)

    Irmeilyana, Puspita, Fitri Maya; Indrawati

    2016-02-01

    The pricing for wireless networks is developed by considering linearity factors, elasticity price and price factors. Mixed Integer Nonlinear Programming of wireless pricing model is proposed as the nonlinear programming problem that can be solved optimally using LINGO 13.0. The solutions are expected to give some information about the connections between the acceptance factor and the price. Previous model worked on the model that focuses on bandwidth as the QoS attribute. The models attempt to maximize the total price for a connection based on QoS parameter. The QoS attributes used will be the bandwidth and the end to end delay that affect the traffic. The maximum goal to maximum price is achieved when the provider determine the requirement for the increment or decrement of price change due to QoS change and amount of QoS value.

  9. End-of-life care and mental illness: a model for community psychiatry and beyond.

    Science.gov (United States)

    Candilis, Philip J; Foti, Mary Ellen G; Holzer, Jacob C

    2004-02-01

    End-of-life care is often influenced by the stereotyping of patients by age, diagnosis, or cultural identity. Two common stereotypes arise from the presumed incompetence of many patients to contribute to end-of-life decisions, and the fear that the discussions themselves will be de-stabilizing. We present a model for end-of-life discussions that combines competence assessment with healthcare preferences in a psychiatric population that faces identical stereotypes. The model, which draws on clinical research in competence and suicide risk assessment, has important implications for all patients in the community who are marginalized or stereotyped during discussions of end-of-life treatment.

  10. End-member modelling as a tool for climate reconstruction-An Eastern Mediterranean case study.

    Science.gov (United States)

    Beuscher, Sarah; Krüger, Stefan; Ehrmann, Werner; Schmiedl, Gerhard; Milker, Yvonne; Arz, Helge; Schulz, Hartmut

    2017-01-01

    The Eastern Mediterranean Sea is a sink for terrigenous sediments from North Africa, Europe and Asia Minor. Its sediments therefore provide valuable information on the climate dynamics in the source areas and the associated transport processes. We present a high-resolution dataset of sediment core M40/4_SL71, which was collected SW of Crete and spans the last ca. 180 kyr. We analysed the clay mineral composition, the grain size distribution within the silt fraction, and the abundance of major and trace elements. We tested the potential of end-member modelling on these sedimentological datasets as a tool for reconstructing the climate variability in the source regions and the associated detrital input. For each dataset, we modelled three end members. All end members were assigned to a specific provenance and sedimentary process. In total, three end members were related to the Saharan dust input, and five were related to the fluvial sediment input. One end member was strongly associated with the sapropel layers. The Saharan dust end members of the grain size and clay mineral datasets generally suggest enhanced dust export into the Eastern Mediterranean Sea during the dry phases with short-term increases during Heinrich events. During the African Humid Periods, dust export was reduced but may not have completely ceased. The loading patterns of two fluvial end members show a strong relationship with the Northern Hemisphere insolation, and all fluvial end members document enhanced input during the African Humid Periods. The sapropel end member most likely reflects the fixation of redox-sensitive elements within the anoxic sapropel layers. Our results exemplify that end-member modelling is a valuable tool for interpreting extensive and multidisciplinary datasets.

  11. End-to-End Availability Analysis of IMS-Based Networks

    DEFF Research Database (Denmark)

    Kamyod, Chayapol; Nielsen, Rasmus Hjorth; Prasad, Neeli R.

    2013-01-01

    Generation Networks (NGNs). In this paper, an end-to-end availability model is proposed and evaluated using a combination of Reliability Block Diagrams (RBD) and a proposed five-state Markov model. The overall availability for intra- and inter domain communication in IMS is analyzed, and the state...

  12. A Rational Model of the Closed-End Fund Discount

    OpenAIRE

    Jonathan Berk; Richard Stanton

    2004-01-01

    The discount on closed-end funds is widely accepted as proof of investor irrationality. We show,however, that a parsimonious rational model can generate a discount that exhibits many of the characteristics observed in practice. The only required features of the model are that managers have (imperfectly observable) ability to generate excess returns; they sign long-term contracts guaranteeing them a fee each year equal to a fixed fraction of assets under management; and they can leave to earn ...

  13. Lateral Penumbra Modelling Based Leaf End Shape Optimization for Multileaf Collimator in Radiotherapy

    Directory of Open Access Journals (Sweden)

    Dong Zhou

    2016-01-01

    Full Text Available Lateral penumbra of multileaf collimator plays an important role in radiotherapy treatment planning. Growing evidence has revealed that, for a single-focused multileaf collimator, lateral penumbra width is leaf position dependent and largely attributed to the leaf end shape. In our study, an analytical method for leaf end induced lateral penumbra modelling is formulated using Tangent Secant Theory. Compared with Monte Carlo simulation and ray tracing algorithm, our model serves well the purpose of cost-efficient penumbra evaluation. Leaf ends represented in parametric forms of circular arc, elliptical arc, Bézier curve, and B-spline are implemented. With biobjective function of penumbra mean and variance introduced, genetic algorithm is carried out for approximating the Pareto frontier. Results show that for circular arc leaf end objective function is convex and convergence to optimal solution is guaranteed using gradient based iterative method. It is found that optimal leaf end in the shape of Bézier curve achieves minimal standard deviation, while using B-spline minimum of penumbra mean is obtained. For treatment modalities in clinical application, optimized leaf ends are in close agreement with actual shapes. Taken together, the method that we propose can provide insight into leaf end shape design of multileaf collimator.

  14. Lateral Penumbra Modelling Based Leaf End Shape Optimization for Multileaf Collimator in Radiotherapy

    Science.gov (United States)

    Zhou, Dong; Zhang, Hui; Ye, Peiqing

    2016-01-01

    Lateral penumbra of multileaf collimator plays an important role in radiotherapy treatment planning. Growing evidence has revealed that, for a single-focused multileaf collimator, lateral penumbra width is leaf position dependent and largely attributed to the leaf end shape. In our study, an analytical method for leaf end induced lateral penumbra modelling is formulated using Tangent Secant Theory. Compared with Monte Carlo simulation and ray tracing algorithm, our model serves well the purpose of cost-efficient penumbra evaluation. Leaf ends represented in parametric forms of circular arc, elliptical arc, Bézier curve, and B-spline are implemented. With biobjective function of penumbra mean and variance introduced, genetic algorithm is carried out for approximating the Pareto frontier. Results show that for circular arc leaf end objective function is convex and convergence to optimal solution is guaranteed using gradient based iterative method. It is found that optimal leaf end in the shape of Bézier curve achieves minimal standard deviation, while using B-spline minimum of penumbra mean is obtained. For treatment modalities in clinical application, optimized leaf ends are in close agreement with actual shapes. Taken together, the method that we propose can provide insight into leaf end shape design of multileaf collimator. PMID:27110274

  15. Lateral Penumbra Modelling Based Leaf End Shape Optimization for Multileaf Collimator in Radiotherapy.

    Science.gov (United States)

    Zhou, Dong; Zhang, Hui; Ye, Peiqing

    2016-01-01

    Lateral penumbra of multileaf collimator plays an important role in radiotherapy treatment planning. Growing evidence has revealed that, for a single-focused multileaf collimator, lateral penumbra width is leaf position dependent and largely attributed to the leaf end shape. In our study, an analytical method for leaf end induced lateral penumbra modelling is formulated using Tangent Secant Theory. Compared with Monte Carlo simulation and ray tracing algorithm, our model serves well the purpose of cost-efficient penumbra evaluation. Leaf ends represented in parametric forms of circular arc, elliptical arc, Bézier curve, and B-spline are implemented. With biobjective function of penumbra mean and variance introduced, genetic algorithm is carried out for approximating the Pareto frontier. Results show that for circular arc leaf end objective function is convex and convergence to optimal solution is guaranteed using gradient based iterative method. It is found that optimal leaf end in the shape of Bézier curve achieves minimal standard deviation, while using B-spline minimum of penumbra mean is obtained. For treatment modalities in clinical application, optimized leaf ends are in close agreement with actual shapes. Taken together, the method that we propose can provide insight into leaf end shape design of multileaf collimator.

  16. A practice model for rural district nursing success in end-of-life advocacy care.

    Science.gov (United States)

    Reed, Frances M; Fitzgerald, Les; Bish, Melanie R

    2017-08-24

    The development of a practice model for rural district nursing successful end-of-life advocacy care. Resources to help people live well in the end stages of life in rural areas can be limited and difficult to access. District nurse advocacy may promote end-of-life choice for people living at home in rural Australia. The lack of evidence available internationally to inform practice in this context was addressed by exploratory study. A pragmatic mixed method study approved by the University Faculty Ethics Committee and conducted from March 2014 to August 2015 was used to explore the successful end-of-life advocacy of 98 rural Australian district nurses. The findings and results were integrated then compared with theory in this article to develop concepts for a practice model. The model illustrates rural district nurse advocacy success based on respect for the rights and values of people. Advocacy action is motivated by the emotional responses of nurses to the end-of-life vulnerability people experience. The combination of willing investment in relationships, knowing the rural people and resources, and feeling supported, together enables district nurses to develop therapeutic emotional intelligence. This skill promotes moral agency in reflection and advocacy action to overcome emotional and ethical care challenges of access and choice using holistic assessment, communication, organisation of resources and empowering support for the self-determination of person-centred end-of-life goals. Recommendations are proposed from the theoretical concepts in the model. Testing the model in practice is recommended to gain the perceptions of a broader range of rural people both giving and receiving end-of-life-care. A model developed by gathering and comparing district nursing experiences and understanding using mixed methods and existing theory offers evidence for practice of a philosophy of successful person-centred advocacy care in a field of nursing that lacks specific

  17. Surface roughness prediction model in end milling of Al/SiCp MMC ...

    African Journals Online (AJOL)

    user

    2 Department of Mechanical Engineering, Pondicherry Engineering College, ... Keywords: Surface roughness (Ra), Response surface method (RSM), End milling, .... To establish the initial model and refined model, a software package MiniTab ..... The After building the regression model, a numerical optimization technique ...

  18. Comparison of the CATHENA model of Gentilly-2 end shield cooling system predictions to station data

    Energy Technology Data Exchange (ETDEWEB)

    Zagre, G.; Sabourin, G. [Candu Energy Inc., Montreal, Quebec (Canada); Chapados, S. [Hydro-Quebec, Montreal, Quebec (Canada)

    2012-07-01

    As part of the Gentilly-2 Refurbishment Project, Hydro-Quebec has elected to perform the End Shield Cooling Safety Analysis. A CATHENA model of Gentilly-2 End Shield Cooling System was developed for this purpose. This model includes new elements compared to other CANDU6 End Shield Cooling models such as a detailed heat exchanger and control logic model. In order to test the model robustness and accuracy, the model predictions were compared with plant measurements.This paper summarizes this comparison between the model predictions and the station measurements. It is shown that the CATHENA model is flexible and accurate enough to predict station measurements for critical parameters, and the detailed heat exchanger model allows reproducing station transients. (author)

  19. Learning of Cross-Sectional Anatomy Using Clay Models

    Science.gov (United States)

    Oh, Chang-Seok; Kim, Ji-Young; Choe, Yeon Hyeon

    2009-01-01

    We incorporated clay modeling into gross anatomy and neuro-anatomy courses to help students understand cross-sectional anatomy. By making clay models, cutting them and comparing cut surfaces to CT and MR images, students learned how cross-sectional two-dimensional images were created from three-dimensional structure of human organs. Most students…

  20. Effects of cross-section on mechanical properties of Au nanowire

    Energy Technology Data Exchange (ETDEWEB)

    Vazinishayan, Ali; Yang, Shuming, E-mail: shuming.yang@mail.xjtu.edu.cn; Duongthipthewa, Anchalee; Wang, Yiming [State Key Laboratory for manufacturing system engineering, Xi’an Jiaotong University, Xi’an, 710049 (China)

    2016-02-15

    The aim of this paper is study of the effects of multiple cross-section of Au nanowire on mechanical properties. Different cross-section models of Au nanowires including circular, hexagonal, pentagonal and rectangular were simulated by finite element modeling using ABAQUS. In this study, the bending technique was applied so that both ends of the model were clamped with mid-span under loading condition. The cross-sections had the length of 400 nm and the diameter of 40 nm, except the circular cross-section while the rest of the cross-sections had an equivalent diameter. Von Misses stresses distribution were used to define the stress distribution in the cross-section under loading condition, and elastic deformation was analyzed by the beam theory. The results disclosed that the circular and the rectangular models had highest and lowest strengths against plastic deformation, respectively.

  1. Cyberinfrastructure for End-to-End Environmental Explorations

    Science.gov (United States)

    Merwade, V.; Kumar, S.; Song, C.; Zhao, L.; Govindaraju, R.; Niyogi, D.

    2007-12-01

    The design and implementation of a cyberinfrastructure for End-to-End Environmental Exploration (C4E4) is presented. The C4E4 framework addresses the need for an integrated data/computation platform for studying broad environmental impacts by combining heterogeneous data resources with state-of-the-art modeling and visualization tools. With Purdue being a TeraGrid Resource Provider, C4E4 builds on top of the Purdue TeraGrid data management system and Grid resources, and integrates them through a service-oriented workflow system. It allows researchers to construct environmental workflows for data discovery, access, transformation, modeling, and visualization. Using the C4E4 framework, we have implemented an end-to-end SWAT simulation and analysis workflow that connects our TeraGrid data and computation resources. It enables researchers to conduct comprehensive studies on the impact of land management practices in the St. Joseph watershed using data from various sources in hydrologic, atmospheric, agricultural, and other related disciplines.

  2. 7 CFR 51.1240 - Paper ends.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Paper ends. 51.1240 Section 51.1240 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Cleaned Virginia Type Peanuts in the Shell Definitions § 51.1240 Paper ends. Paper ends means...

  3. Flexible End2End Workflow Automation of Hit-Discovery Research.

    Science.gov (United States)

    Holzmüller-Laue, Silke; Göde, Bernd; Thurow, Kerstin

    2014-08-01

    The article considers a new approach of more complex laboratory automation at the workflow layer. The authors purpose the automation of end2end workflows. The combination of all relevant subprocesses-whether automated or manually performed, independently, and in which organizational unit-results in end2end processes that include all result dependencies. The end2end approach focuses on not only the classical experiments in synthesis or screening, but also on auxiliary processes such as the production and storage of chemicals, cell culturing, and maintenance as well as preparatory activities and analyses of experiments. Furthermore, the connection of control flow and data flow in the same process model leads to reducing of effort of the data transfer between the involved systems, including the necessary data transformations. This end2end laboratory automation can be realized effectively with the modern methods of business process management (BPM). This approach is based on a new standardization of the process-modeling notation Business Process Model and Notation 2.0. In drug discovery, several scientific disciplines act together with manifold modern methods, technologies, and a wide range of automated instruments for the discovery and design of target-based drugs. The article discusses the novel BPM-based automation concept with an implemented example of a high-throughput screening of previously synthesized compound libraries. © 2014 Society for Laboratory Automation and Screening.

  4. 49 CFR 238.413 - End structures of trailer cars.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false End structures of trailer cars. 238.413 Section... II Passenger Equipment § 238.413 End structures of trailer cars. (a) Except as provided in paragraph (b) of this section, the end structure of a trailer car shall be designed to include the following...

  5. Building dialogue POMDPs from expert dialogues an end-to-end approach

    CERN Document Server

    Chinaei, Hamidreza

    2016-01-01

    This book discusses the Partially Observable Markov Decision Process (POMDP) framework applied in dialogue systems. It presents POMDP as a formal framework to represent uncertainty explicitly while supporting automated policy solving. The authors propose and implement an end-to-end learning approach for dialogue POMDP model components. Starting from scratch, they present the state, the transition model, the observation model and then finally the reward model from unannotated and noisy dialogues. These altogether form a significant set of contributions that can potentially inspire substantial further work. This concise manuscript is written in a simple language, full of illustrative examples, figures, and tables. Provides insights on building dialogue systems to be applied in real domain Illustrates learning dialogue POMDP model components from unannotated dialogues in a concise format Introduces an end-to-end approach that makes use of unannotated and noisy dialogue for learning each component of dialogue POM...

  6. Models for Photon-photon Total Cross-sections

    OpenAIRE

    Godbole, RM; Grau, A; Pancheri, G

    1999-01-01

    We present here a brief overview of recent models describing the photon-photon cross-section into hadrons. We shall show in detail results from the eikonal minijet model, with and without soft gluon summation.

  7. One size does not fit all - understanding the front-end and back-ens of business model innovation

    DEFF Research Database (Denmark)

    Günzel, Franziska; Holm, Anna B.

    2013-01-01

    Business model innovation is becoming a central research topic in management. However, a lack of a common understanding of the nature of the business model leads to disregarding its multifaceted structure when analyzing the business model innovation process. This article proposes a more detailed...... understanding of the business model innovation process by drawing on existing knowledge from new product development literature and examining the front-end and the back-end of business model innovation of three leading Danish newspapers. We studied how changes introduced during the development of digital news...... production and delivery have affected key components of these business models, namely value creation, proposition, delivery and capture in the period 2002–2011. Our findings suggest the need to distinguish between front-end and back-end business model innovation processes, and to recognize the importance...

  8. Estimating teat canal cross-sectional area to determine the effects of teat-end and mouthpiece chamber vacuum on teat congestion.

    Science.gov (United States)

    Penry, J F; Upton, J; Mein, G A; Rasmussen, M D; Ohnstad, I; Thompson, P D; Reinemann, D J

    2017-01-01

    The primary objective of this experiment was to assess the effect of mouthpiece chamber vacuum on teat-end congestion. The secondary objective was to assess the interactive effects of mouthpiece chamber vacuum with teat-end vacuum and pulsation setting on teat-end congestion. The influence of system vacuum, pulsation settings, mouthpiece chamber vacuum, and teat-end vacuum on teat-end congestion were tested in a 2×2 factorial design. The low-risk conditions for teat-end congestion (TEL) were 40 kPa system vacuum (Vs) and 400-ms pulsation b-phase. The high-risk conditions for teat-end congestion (TEH) were 49 kPa Vs and 700-ms b-phase. The low-risk condition for teat-barrel congestion (TBL) was created by venting the liner mouthpiece chamber to atmosphere. In the high-risk condition for teat-barrel congestion (TBH) the mouthpiece chamber was connected to short milk tube vacuum. Eight cows (32 quarters) were used in the experiment conducted during 0400 h milkings. All cows received all treatments over the entire experimental period. Teatcups were removed after 150 s for all treatments to standardize the exposure period. Calculated teat canal cross-sectional area (CA) was used to assess congestion of teat tissue. The main effect of the teat-end treatment was a reduction in CA of 9.9% between TEL and TEH conditions, for both levels of teat-barrel congestion risk. The main effect of the teat-barrel treatment was remarkably similar, with a decrease of 9.7% in CA between TBL and TBH conditions for both levels of teat-end congestion risk. No interaction between treatments was detected, hence the main effects are additive. The most aggressive of the 4 treatment combinations (TEH plus TBH) had a CA estimate 20% smaller than for the most gentle treatment combination (TEL plus TBL). The conditions designed to impair circulation in the teat barrel also had a deleterious effect on circulation at the teat end. This experiment highlights the importance of elevated mouthpiece

  9. Mathematical models of the pregnant woman at the end of the first trimester

    International Nuclear Information System (INIS)

    Watson, E.E.; Stabin, M.G.; Eckerman, K.F.; Cristy, M.; Ryman, J.C.; Davis, J.F.

    1989-01-01

    Most calculations of absorbed doses from radionuclides in the body are based on a mathematical model of Reference Man with no consideration of persons of different sizes nor of the different geometric relationships of organs as in women and children. This is inappropriate for the pregnant woman, particularly as the pregnancy progresses. Many of the mother's abdominal organs are repositioned and their shapes changed. Existing mathematical models need to be modified to reflect these changes and improve the accuracy of absorbed dose estimates. Models of the pregnant woman at the end of the first and third trimester have been developed. These models are modifications of the adult female model that is part of the Oak Ridge National Laboratory phantom series. The models for both the three- and nine-month models were patterned after anatomic information appearing in obstetric texts and reports. The three-month model incorporated changes in the size and shape of the uterus as well as in the urinary bladder, the small intestine, and portions of the large intestine. The changes in the Reference Woman model to approximate the nine-month model are much more extensive. Many organs including the uterus plus contents, stomach, small intestine, upper and lower large intestine, pelvis, urinary bladder, and liver were remodeled. The outside of the trunk also had to be enlarged to accommodate the uterus. Volumes for the mother's organs were maintained at the values proposed for the Reference Woman phantom. The uterine contents at nine-months were divided into fetal soft tissues, fetal skeleton, and other tissues within the uterus so that estimates of specific absorbed fractions can be calculated for various sections of the fetus as well as for the total fetus

  10. Biomethane storage: Evaluation of technologies, end uses, business models, and sustainability

    International Nuclear Information System (INIS)

    Budzianowski, Wojciech M.; Brodacka, Marlena

    2017-01-01

    Highlights: • Biomethane storage integrates the different energy subsystems. • It facilitates adoption of solar and wind energy sources. • It is essential to adequately match storages with their end uses and business models. • Business models must propose, create, and capture value linked with gas storage. • Sustainable is economically viable, environmentally benign, and socially beneficial. - Abstract: Biomethane is a renewable gas that can be turned into dispatchable resource through applying storage techniques. The storage enables the discharge of stored biomethane at any time and place it is required as gas turbine power, heat or transport fuel. Thus the stored biomethane could more efficiently serve various energy applications in the power, transport, heat, and gas systems as well as in industry. Biomethane storage may therefore integrate the different energy subsystems making the whole energy system more efficient. This work provides an overview and evaluation of biomethane storage technologies, end uses, business models and sustainability. It is shown that storage technologies are versatile, have different costs and efficiencies and may serve different end uses. Business models may be created or selected to fit regional spatial contexts, realistic demands for gas storage related services, and the level of available subsidies. By applying storage the sustainability of biomethane is greatly improved in terms of economic viability, reduced environmental impacts and greater social benefits. Stored biomethane may greatly facilitate adoption of intermittent renewable energy sources such as solar and wind. Other findings show that biomethane storage needs to be combined with grid services and other similar services to reduce overall storage costs.

  11. GridLAB-D Technical Support Document: Residential End-Use Module Version 1.0

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Zachary T.; Gowri, Krishnan; Katipamula, Srinivas

    2008-07-31

    1.0 Introduction The residential module implements the following end uses and characteristics to simulate the power demand in a single family home: • Water heater • Lights • Dishwasher • Range • Microwave • Refrigerator • Internal gains (plug loads) • House (heating/cooling loads) The house model considers the following four major heat gains/losses that contribute to the building heating/cooling load: 1. Conduction through exterior walls, roof and fenestration (based on envelope UA) 2. Air infiltration (based on specified air change rate) 3. Solar radiation (based on CLTD model and using tmy data) 4. Internal gains from lighting, people, equipment and other end use objects. The Equivalent Thermal Parameter (ETP) approach is used to model the residential loads and energy consumption. The following sections describe the modeling assumptions for each of the above end uses and the details of power demand calculations in the residential module.

  12. Optical Model and Cross Section Uncertainties

    Energy Technology Data Exchange (ETDEWEB)

    Herman,M.W.; Pigni, M.T.; Dietrich, F.S.; Oblozinsky, P.

    2009-10-05

    Distinct minima and maxima in the neutron total cross section uncertainties were observed in model calculations using spherical optical potential. We found this oscillating structure to be a general feature of quantum mechanical wave scattering. Specifically, we analyzed neutron interaction with 56Fe from 1 keV up to 65 MeV, and investigated physical origin of the minima.We discuss their potential importance for practical applications as well as the implications for the uncertainties in total and absorption cross sections.

  13. Mathematical modeling of a multi-product EMQ model with an enhanced end items issuing policy and failures in rework.

    Science.gov (United States)

    Chiu, Yuan-Shyi Peter; Sung, Peng-Cheng; Chiu, Singa Wang; Chou, Chung-Li

    2015-01-01

    This study uses mathematical modeling to examine a multi-product economic manufacturing quantity (EMQ) model with an enhanced end items issuing policy and rework failures. We assume that a multi-product EMQ model randomly generates nonconforming items. All of the defective are reworked, but a certain portion fails and becomes scraps. When rework process ends and the entire lot of each product is quality assured, a cost reduction n + 1 end items issuing policy is used to transport finished items of each product. As a result, a closed-form optimal production cycle time is obtained. A numerical example demonstrates the practical usage of our result and confirms a significant savings in stock holding and overall production costs as compared to that of a prior work (Chiu et al. in J Sci Ind Res India, 72:435-440 2013) in the literature.

  14. Lake Representations in Global Climate Models: An End-User Perspective

    Science.gov (United States)

    Rood, R. B.; Briley, L.; Steiner, A.; Wells, K.

    2017-12-01

    The weather and climate in the Great Lakes region of the United States and Canada are strongly influenced by the lakes. Within global climate models, lakes are incorporated in many ways. If one is interested in quantitative climate information for the Great Lakes, then it is a first principle requirement that end-users of climate model simulation data, whether scientists or practitioners, need to know if and how lakes are incorporated into models. We pose the basic question, how are lakes represented in CMIP models? Despite significant efforts by the climate community to document and publish basic information about climate models, it is unclear how to answer the question about lake representations? With significant knowledge of the practice of the field, then a reasonable starting point is to use the ES-DOC Comparator (https://compare.es-doc.org/ ). Once at this interface to model information, the end-user is faced with the need for more knowledge about the practice and culture of the discipline. For example, lakes are often categorized as a type of land, a counterintuitive concept. In some models, though, lakes are specified in ocean models. There is little evidence and little confidence that the information obtained through this process is complete or accurate. In fact, it is verifiably not accurate. This experience, then, motivates identifying and finding either human experts or technical documentation for each model. The conclusion from this exercise is that it can take months or longer to provide a defensible answer to if and how lakes are represented in climate models. Our experience with lake finding is that this is not a unique experience. This talk documents our experience and explores barriers we have identified and strategies for reducing those barriers.

  15. A global reference for caesarean section rates (C-Model): a multicountry cross-sectional study.

    Science.gov (United States)

    Souza, J P; Betran, A P; Dumont, A; de Mucio, B; Gibbs Pickens, C M; Deneux-Tharaux, C; Ortiz-Panozo, E; Sullivan, E; Ota, E; Togoobaatar, G; Carroli, G; Knight, H; Zhang, J; Cecatti, J G; Vogel, J P; Jayaratne, K; Leal, M C; Gissler, M; Morisaki, N; Lack, N; Oladapo, O T; Tunçalp, Ö; Lumbiganon, P; Mori, R; Quintana, S; Costa Passos, A D; Marcolin, A C; Zongo, A; Blondel, B; Hernández, B; Hogue, C J; Prunet, C; Landman, C; Ochir, C; Cuesta, C; Pileggi-Castro, C; Walker, D; Alves, D; Abalos, E; Moises, Ecd; Vieira, E M; Duarte, G; Perdona, G; Gurol-Urganci, I; Takahiko, K; Moscovici, L; Campodonico, L; Oliveira-Ciabati, L; Laopaiboon, M; Danansuriya, M; Nakamura-Pereira, M; Costa, M L; Torloni, M R; Kramer, M R; Borges, P; Olkhanud, P B; Pérez-Cuevas, R; Agampodi, S B; Mittal, S; Serruya, S; Bataglia, V; Li, Z; Temmerman, M; Gülmezoglu, A M

    2016-02-01

    To generate a global reference for caesarean section (CS) rates at health facilities. Cross-sectional study. Health facilities from 43 countries. Thirty eight thousand three hundred and twenty-four women giving birth from 22 countries for model building and 10,045,875 women giving birth from 43 countries for model testing. We hypothesised that mathematical models could determine the relationship between clinical-obstetric characteristics and CS. These models generated probabilities of CS that could be compared with the observed CS rates. We devised a three-step approach to generate the global benchmark of CS rates at health facilities: creation of a multi-country reference population, building mathematical models, and testing these models. Area under the ROC curves, diagnostic odds ratio, expected CS rate, observed CS rate. According to the different versions of the model, areas under the ROC curves suggested a good discriminatory capacity of C-Model, with summary estimates ranging from 0.832 to 0.844. The C-Model was able to generate expected CS rates adjusted for the case-mix of the obstetric population. We have also prepared an e-calculator to facilitate use of C-Model (www.who.int/reproductivehealth/publications/maternal_perinatal_health/c-model/en/). This article describes the development of a global reference for CS rates. Based on maternal characteristics, this tool was able to generate an individualised expected CS rate for health facilities or groups of health facilities. With C-Model, obstetric teams, health system managers, health facilities, health insurance companies, and governments can produce a customised reference CS rate for assessing use (and overuse) of CS. The C-Model provides a customized benchmark for caesarean section rates in health facilities and systems. © 2015 World Health Organization; licensed by John Wiley & Sons Ltd on behalf of Royal College of Obstetricians and Gynaecologists.

  16. 78 FR 8535 - Medicare Program: Comprehensive End-Stage Renal Disease Care Model Announcement

    Science.gov (United States)

    2013-02-06

    ... develop and test innovative health care payment and service delivery models that show promise of reducing... test innovative payment and service delivery models that reduce spending under Medicare, Medicaid or...] Medicare Program: Comprehensive End-Stage Renal Disease Care Model Announcement AGENCY: Centers for...

  17. Content Model Use and Development to Redeem Thin Section Records

    Science.gov (United States)

    Hills, D. J.

    2014-12-01

    The National Geothermal Data System (NGDS) is a catalog of documents and datasets that provide information about geothermal resources located primarily within the United States. The goal of NGDS is to make large quantities of geothermal-relevant geoscience data available to the public by creating a national, sustainable, distributed, and interoperable network of data providers. The Geological Survey of Alabama (GSA) has been a data provider in the initial phase of NGDS. One method by which NGDS facilitates interoperability is through the use of content models. Content models provide a schema (structure) for submitted data. Schemas dictate where and how data should be entered. Content models use templates that simplify data formatting to expedite use by data providers. These methodologies implemented by NGDS can extend beyond geothermal data to all geoscience data. The GSA, using the NGDS physical samples content model, has tested and refined a content model for thin sections and thin section photos. Countless thin sections have been taken from oil and gas well cores housed at the GSA, and many of those thin sections have related photomicrographs. Record keeping for these thin sections has been scattered at best, and it is critical to capture their metadata while the content creators are still available. A next step will be to register the GSA's thin sections with SESAR (System for Earth Sample Registration) and assign an IGSN (International Geo Sample Number) to each thin section. Additionally, the thin section records will be linked to the GSA's online record database. When complete, the GSA's thin sections will be more readily discoverable and have greater interoperability. Moving forward, the GSA is implementing use of NGDS-like content models and registration with SESAR and IGSN to improve collection maintenance and management of additional physical samples.

  18. Development of a global computable general equilibrium model coupled with detailed energy end-use technology

    International Nuclear Information System (INIS)

    Fujimori, Shinichiro; Masui, Toshihiko; Matsuoka, Yuzuru

    2014-01-01

    Highlights: • Detailed energy end-use technology information is considered within a CGE model. • Aggregated macro results of the detailed model are similar to traditional model. • The detailed model shows unique characteristics in the household sector. - Abstract: A global computable general equilibrium (CGE) model integrating detailed energy end-use technologies is developed in this paper. The paper (1) presents how energy end-use technologies are treated within the model and (2) analyzes the characteristics of the model’s behavior. Energy service demand and end-use technologies are explicitly considered, and the share of technologies is determined by a discrete probabilistic function, namely a Logit function, to meet the energy service demand. Coupling with detailed technology information enables the CGE model to have more realistic representation in the energy consumption. The proposed model in this paper is compared with the aggregated traditional model under the same assumptions in scenarios with and without mitigation roughly consistent with the two degree climate mitigation target. Although the results of aggregated energy supply and greenhouse gas emissions are similar, there are three main differences between the aggregated and the detailed technologies models. First, GDP losses in mitigation scenarios are lower in the detailed technology model (2.8% in 2050) as compared with the aggregated model (3.2%). Second, price elasticity and autonomous energy efficiency improvement are heterogeneous across regions and sectors in the detailed technology model, whereas the traditional aggregated model generally utilizes a single value for each of these variables. Third, the magnitude of emissions reduction and factors (energy intensity and carbon factor reduction) related to climate mitigation also varies among sectors in the detailed technology model. The household sector in the detailed technology model has a relatively higher reduction for both energy

  19. A gastrocnemius heterotopical transplant model with end-to-side neurorraphy

    OpenAIRE

    Jaeger, Marcos Ricardo de Oliveira; Braga Silva, Jefferson [UNIFESP; Bain, James; Ely, Pedro Bins; Pires, Jefferson André; Ferreira, Lydia Masako [UNIFESP

    2014-01-01

    PURPOSE:To present an animal model to assess the effects of end-to-side innervation in the heterotopically transplanted model with reduced chances of neural contamination.METHODS: The medial portion of the gastrocnemius muscle in wistar male rats was isolated and its pedicle dissected and performed a flap in the abdominal portion. To prevent neural contamination in the abdominal region, the muscle was wrapped with a Goretex(r) sheet. The specimens were divided into 2 groups (G). In G1 was per...

  20. Argos: Residential end-use simulation model for load management strategy analysis

    International Nuclear Information System (INIS)

    Capasso, A.; Lamedica, R.; Prudenzi, A.

    1992-01-01

    In recent years, load management (LM) strategies, aimed at the optimization of available energy resources, as well as, the reduction of investments for new power plants, have been applied worldwide in residential end-use assessments. However, the forecasting of LM strategy impacts on the residential sector is very complex because it is based on a preliminary evaluation of the customers' proclivity to adapt their load characteristics to utility aims. In order to reduce load analysis requirements, which are substantial due to the need for thorough statistical analyses, complex field tests and measurements, the availability of models taking into account customer behavioural aspects is of paramount importance. This paper illustrates a simulation model which allows the performance of numerical evaluations concerning the effectiveness of some LM strategies applied to a residential end-use area load profile as previously determined by the aggregation of the contributions of individual households. This model enabled the evaluation of the impact, on the load profile, of a time-of-day tariff such as that recently introduced in Italy

  1. SU-E-T-430: Modeling MLC Leaf End in 2D for Sliding Window IMRT and Arc Therapy

    International Nuclear Information System (INIS)

    Liang, X; Zhu, T

    2014-01-01

    Purpose: To develop a 2D geometric model for MLC accounting for leaf end dose leakage for dynamic IMRT and Rapidarc therapy. Methods: Leaf-end dose leakage is one of the problems for MLC dose calculation and modeling. Dosimetric leaf gap used to model the MLC and to count for leakage in dose calculation, but may not be accurate for smaller leaf gaps. We propose another geometric modeling method to compensate for the MLC round-shape leaf ends dose leakage, and improve the accuracy of dose calculation and dose verification. A triangular function is used to geometrically model the MLC leaf end leakage in the leaf motion direction, and a step function is used in the perpendicular direction. Dose measurements with different leaf gap, different window width, and different window height were conducted, and the results were used to fit the analytical model to get the model parameters. Results: Analytical models have been obtained for stop-and-shoot and dynamic modes for MLC motion. Parameters a=0.4, lw'=5.0 mm for 6X and a=0.54, lw'=4.1 mm for 15x were obtained from the fitting process. The proposed MLC leaf end model improves the dose profile at the two ends of the sliding window opening. This improvement is especially significant for smaller sliding window openings, which are commonly used for highly modulated IMRT plans and arc therapy plans. Conclusion: This work models the MLC round leaf end shape and movement pattern for IMRT dose calculation. The theory, as well as the results in this work provides a useful tool for photon beam IMRT dose calculation and verification

  2. Domain wall partition function of the eight-vertex model with a non-diagonal reflecting end

    International Nuclear Information System (INIS)

    Yang Wenli; Chen Xi; Feng Jun; Hao Kun; Shi Kangjie; Sun Chengyi; Yang Zhanying; Zhang Yaozhong

    2011-01-01

    With the help of the Drinfeld twist or factorizing F-matrix for the eight-vertex SOS model, we derive the recursion relations of the partition function for the eight-vertex model with a generic non-diagonal reflecting end and domain wall boundary condition. Solving the recursion relations, we obtain the explicit determinant expression of the partition function. Our result shows that, contrary to the eight-vertex model without a reflecting end, the partition function can be expressed as a single determinant.

  3. A Variable Flow Modelling Approach To Military End Strength Planning

    Science.gov (United States)

    2016-12-01

    function. The MLRPS is more complex than the variable flow model as it has to cater for a force structure that is much larger than just the MT branch...essential positions in a Ship’s complement, or by the biggest current deficit in forecast end strength. The model can be adjusted to cater for any of these...is unlikely that the RAN will be able to cater for such an increase in hires, so this scenario is not likely to solve their problem. Each transition

  4. The effect of support springs in ends welded gap hollow YT-joint

    Directory of Open Access Journals (Sweden)

    R. F. Vieira

    Full Text Available This paper presents an analysis on the effect of support springs in an ends circular hollow sections welded into a YT joint. The overall behavior and failure of the joint were characterized under axial compression of the lap brace. Two joint failure modes were identified: chord wall plastification (Mode A and cross-sectional chord buckling (Mode F in the region below the lap brace. The system was modeled with and without support springs using the numerical finite element program Ansys. Model results were compared with experimental data in terms of principal stress in the joint intersection. The finite element model without support springs proved to be more accurate than that with support springs.

  5. Sectioning Clay Models Makes Anatomy & Development Tangible

    Science.gov (United States)

    Howell, Carina Endres; Howell, James Endres

    2010-01-01

    Clay models have proved to be useful teaching aids for many topics in biology that depend on three-dimensional reasoning. Students studying embryonic development struggle to mentally reconstruct the three-dimensional structure of embryos and larvae by observing prepared slides of cross-sectional slices. Students who build clay models of embryos…

  6. Learning end-of-life care within a constructivist model: Undergraduate nursing students’ experiences

    Directory of Open Access Journals (Sweden)

    Anna E. van der Wath

    2015-11-01

    Full Text Available Background: Although nursing education aims to equip nursing students to provide care to dying patients and their families, nurses often feel ill-prepared to cope with the emotional labour involved in end-of-life care. Objectives: The aim of the study was to explore and describe nursing students’ experiences of end-of-life care through experiential learning within a constructivist educational model. Method: A qualitative, descriptive design was used. As part of introducing experiential learning, innovative educational practices were initiated during a second year level undergraduate nursing module on end-of-life care. Qualitative data on second-year nursing students’ experiences were collected through written reflections and analysed using open coding. Results: The themes that emerged revealed participants’ sensory and emotional experiences during the learning opportunities. Participants reflected on what they learnt and clarified their values related to death and dying. They indicated how they would apply the new meanings constructed in clinical practice. Conclusion: A constructivist educational model of experiential learning holds potential to enhance value clarification and nursing students’ sensory and emotional awareness of death and dying. Experiential learning is recommended to develop nursing students’ competency inproviding end-of-life care.

  7. Turbine airfoil having outboard and inboard sections

    Science.gov (United States)

    Mazzola, Stefan; Marra, John J

    2015-03-17

    A turbine airfoil usable in a turbine engine and formed from at least an outboard section and an inboard section such that an inner end of the outboard section is attached to an outer end of the inboard section. The outboard section may be configured to provide a tip having adequate thickness and may extend radially inward from the tip with a generally constant cross-sectional area. The inboard section may be configured with a tapered cross-sectional area to support the outboard section.

  8. Scalable Database Design of End-Game Model with Decoupled Countermeasure and Threat Information

    Science.gov (United States)

    2017-11-01

    the Army Modular Active Protection System (MAPS) program to provide end-to-end APS modeling and simulation capabilities. The SSES simulation features...research project of scalable database design was initiated in support of SSES modularization efforts with respect to 4 major software components...Iron Curtain KE kinetic energy MAPS Modular Active Protective System OLE DB object linking and embedding database RDB relational database RPG

  9. Modelling interaction cross sections for intermediate and low energy ions

    International Nuclear Information System (INIS)

    Toburen, L.H.; Shinpaugh, J.L.; Justiniano, E.L.B.

    2002-01-01

    When charged particles slow in tissue they undergo electron capture and loss processes than can have profound effects on subsequent interaction cross sections. Although a large amount of data exists for the interaction of bare charged particles with atoms and molecules, few experiments have been reported for these 'dressed' particles. Projectile electrons contribute to an impact-parameter-dependent screening of the projectile charge that precludes straightforward scaling of energy loss cross sections from those of bare charged particles. The objective of this work is to develop an analytical model for the energy-loss-dependent effects of screening on differential ionisation cross sections that can be used in track structure calculations for high LET ions. As a first step a model of differential ionisation cross sections for bare ions has been combined with a simple screening model to explore cross sections for intermediate and low energy dressed ions in collisions with atomic and molecular gas targets. The model is described briefly and preliminary results compared to measured electron energy spectra. (author)

  10. End-to-end System Performance Simulation: A Data-Centric Approach

    Science.gov (United States)

    Guillaume, Arnaud; Laffitte de Petit, Jean-Luc; Auberger, Xavier

    2013-08-01

    In the early times of space industry, the feasibility of Earth observation missions was directly driven by what could be achieved by the satellite. It was clear to everyone that the ground segment would be able to deal with the small amount of data sent by the payload. Over the years, the amounts of data processed by the spacecrafts have been increasing drastically, leading to put more and more constraints on the ground segment performances - and in particular on timeliness. Nowadays, many space systems require high data throughputs and short response times, with information coming from multiple sources and involving complex algorithms. It has become necessary to perform thorough end-to-end analyses of the full system in order to optimise its cost and efficiency, but even sometimes to assess the feasibility of the mission. This paper presents a novel framework developed by Astrium Satellites in order to meet these needs of timeliness evaluation and optimisation. This framework, named ETOS (for “End-to-end Timeliness Optimisation of Space systems”), provides a modelling process with associated tools, models and GUIs. These are integrated thanks to a common data model and suitable adapters, with the aim of building suitable space systems simulators of the full end-to-end chain. A big challenge of such environment is to integrate heterogeneous tools (each one being well-adapted to part of the chain) into a relevant timeliness simulation.

  11. Statistical Modelling of Resonant Cross Section Structure in URR, Model of the Characteristic Function

    International Nuclear Information System (INIS)

    Koyumdjieva, N.

    2006-01-01

    A statistical model for the resonant cross section structure in the Unresolved Resonance Region has been developed in the framework of the R-matrix formalism in Reich Moore approach with effective accounting of the resonance parameters fluctuations. The model uses only the average resonance parameters and can be effectively applied for analyses of cross sections functional, averaged over many resonances. Those are cross section moments, transmission and self-indication functions measured through thick sample. In this statistical model the resonant cross sections structure is accepted to be periodic and the R-matrix is a function of ε=E/D with period 0≤ε≤N; R nc (ε)=π/2√(S n *S c )1/NΣ(i=1,N)(β in *β ic *ctg[π(ε i - = ε-iS i )/N]; Here S n ,S c ,S i is respectively neutron strength function, strength function for fission or inelastic channel and strength function for radiative capture, N is the number of resonances (ε i ,β i ) that obey the statistic of Porter-Thomas and Wigner's one. The simple case of this statistical model concerns the resonant cross section structure for non-fissile nuclei under the threshold for inelastic scattering - the model of the characteristic function with HARFOR program. In the above model some improvements of calculation of the phases and logarithmic derivatives of neutron channels have been done. In the parameterization we use the free parameter R l ∞ , which accounts the influence of long-distant resonances. The above scheme for statistical modelling of the resonant cross section structure has been applied for evaluation of experimental data for total, capture and inelastic cross sections for 232 Th in the URR (4-150) keV and also the transmission and self-indication functions in (4-175) keV. The set of evaluated average resonance parameters have been obtained. The evaluated average resonance parameters in the URR are consistent with those in the Resolved Resonance Region (CRP for Th-U cycle, Vienna, 2006

  12. Peningkatan Kemampuan Pemecahan Masalah dan Komunikasi Matematis Siswa SMP melalui Model Pembelajaran Means-ends Analysis

    Directory of Open Access Journals (Sweden)

    Juanda Juanda

    2014-12-01

    Full Text Available Dalam kurikulum mata pelajaran matematika, siswa dituntut mampu mengembangkan kemampuan matematika dalam pemecahan masalah dan mengkomunikasikan ide atau gagasan dengan menggunakan simbol, tabel, diagram, dan media lain. Oleh karena itu, dibutuhkan model pembelajaran yang tepat untuk meningkatkan kemampuan pemecahan masalah dan komunikasi matematis. Penelitian ini bertujuan untuk; 1 mengetahui peningkatan kemampuan pemecahan masalah dan komunikasi matematis apabila ditinjau keseluruhan siswa dan level kemampuan awal siswa, 2 interaksi antara model pembelajaran dan level kemampuan siswa terhadap peningkatan kemampuan pemecahan masalah dan komunikasi matematis dan 3 sikap siswa terhadap pembelajaran model Means-ends analysis. Penelitian ini menggunakan pendekatan kuantitatif dengan metode eksperimen. Populasi dalam penelitian ini adalah seluruh siswa kelas VIII SMPS YPPU Sigli, Provinsi Aceh, sedangkan sampelnya adalah siswa kelas VIII-1 sebagai kelas eksperimen dan kelas VIII-2 sebagai kelas kontrol. Instrumen yang digunakan adalah jenis tes dan non tes. Analisis data dilakukan secara kuantitatif dengan menggunakan uji-t terhadap rataan gain ternormalisasi antara kedua kelompok sampel  dan uji anova dua jalur untuk menguji interaksi antara model pembelajaran dan level siswa terhadap peningkatan kemampuan matematis siswa. Hasil penelitian menyimpulkan bahwa peningkatan kemampuan pemecahan masalah dan komunikasi matematis siswa yang memperoleh pembelajaran model Means-ends analysis lebih baik daripada siswa yang memperoleh pembelajaran konvensional baik ditinjau berdasarkan keseluruhan siswa maupun berdasarkan level kemampuan siswa. Terdapat interaksi antara faktor model pembelajaran dan level kemampuan siswa terhadap peningkatan kemampuan pemecahan masalah matematis. Tidak terdapat interaksi antara model pembelajaran Means-ends analysis dan level kemampuan siswa terhadap peningkatan kemampuan komunikasi matematis. Siswa memiliki sikap positif

  13. Analytical model for shear strength of end slabs of prestressed concrete nuclear reactor vessels

    International Nuclear Information System (INIS)

    Abdulrahman, H.O.; Sozen, M.A.; Schnobrich, W.C.

    1979-04-01

    The results are presented of an investigation of the behavior and strength of flat end slabs of cylindrical prestressed concrete nuclear reactor vessels. The investigation included tests of ten small-scale pressure vessels and development of a nonlinear finite-element model to simulate the deformation response and strength of the end slabs. Because earlier experimental studies had shown that the flexural strength of the end slab could be calculated using intelligible procedures, the emphasis of this investigation was on shear strength

  14. One size does not fit all - understanding the front-end and back-ens of business model innovation

    OpenAIRE

    Günzel, Franziska; Holm, Anna B.

    2013-01-01

    Business model innovation is becoming a central research topic in management. However, a lack of a common understanding of the nature of the business model leads to disregarding its multifaceted structure when analyzing the business model innovation process. This article proposes a more detailed understanding of the business model innovation process by drawing on existing knowledge from new product development literature and examining the front-end and the back-end of business model innovatio...

  15. 34 CFR 34.26 - Ending garnishment.

    Science.gov (United States)

    2010-07-01

    ... 34 Education 1 2010-07-01 2010-07-01 false Ending garnishment. 34.26 Section 34.26 Education Office of the Secretary, Department of Education ADMINISTRATIVE WAGE GARNISHMENT § 34.26 Ending... to pay any portion of the amount stated in the order, the employer must— (i) Notify us; and (ii...

  16. Means-End based Functional Modeling for Intelligent Control: Modeling and Experiments with an Industrial Heat Pump System

    DEFF Research Database (Denmark)

    Saleem, Arshad

    2007-01-01

    The purpose of this paper is to present a Multilevel Flow Model (MFM) of an industrial heat pump system and its use for diagnostic reasoning. MFM is functional modeling language supporting an explicit means-ends intelligent control strategy for large industrial process plants. The model is used...... in several diagnostic experiments analyzing different fault scenarios. The model and results of the experiments are explained and it is shown how MFM based intelligent modeling and automated reasoning can improve the fault diagnosis process significantly....

  17. Modeling and measurement of the ALS U5 undulator end magnetic structures

    International Nuclear Information System (INIS)

    Humphries, D.; Halbach, K.; Hoyer, E.; Kincaid, B.; Marks, S.; Schlueter, R.

    1993-05-01

    The end structures for the ALS U5.0 undulators utilize a system of dual permanent magnet rotors intended to establish gap independent field performance. They may also be used for tuning of the first and second magnetic field integrals of these devices. The behavior of these structures has been studied by means of a two dimensional modeling with the POISSON Group of computer codes. A parametric study of the magnetic field distribution and first and second integrals of the fields has been conducted. In parallel, magnetic measurements of the final completed structures have been performed using an automated Hall probe measurement system. Results of the modeling and measurements are compared. Implications for tuning of the ends of the devices within the context of the electron beam parameters of the ALS are discussed

  18. Measurements and analysis of end-to-end Internet dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Paxson, Vern [Univ. of California, Berkeley, CA (United States). Computer Science Division

    1997-04-01

    Accurately characterizing end-to-end Internet dynamics - the performance that a user actually obtains from the lengthy series of network links that comprise a path through the Internet - is exceptionally difficult, due to the network`s immense heterogeneity. At the heart of this work is a `measurement framework` in which a number of sites around the Internet host a specialized measurement service. By coordinating `probes` between pairs of these sites one can measure end-to-end behavior along O(N2) paths for a framework consisting of N sites. Consequently, one obtains a superlinear scaling that allows measuring a rich cross-section of Internet behavior without requiring huge numbers of observation points. 37 sites participated in this study, allowing the author to measure more than 1,000 distinct Internet paths. The first part of this work looks at the behavior of end-to-end routing: the series of routers over which a connection`s packets travel. Based on 40,000 measurements made using this framework, the author analyzes: routing `pathologies` such as loops, outages, and flutter; the stability of routes over time; and the symmetry of routing along the two directions of an end-to-end path. The author finds that pathologies increased significantly over the course of 1995 and that Internet paths are heavily dominated by a single route. The second part of this work studies end-to-end Internet packet dynamics. The author analyzes 20,000 TCP transfers of 100 Kbyte each to investigate the performance of both the TCP endpoints and the Internet paths. The measurements used for this part of the study are much richer than those for the first part, but require a great degree of attention to issues of calibration, which are addressed by applying self-consistency checks to the measurements whenever possible. The author finds that packet filters are capable of a wide range of measurement errors, some of which, if undetected, can significantly taint subsequent analysis.

  19. Evaluation of End-Products in Architecture Design Process: A Fuzzy Decision-Making Model

    Directory of Open Access Journals (Sweden)

    Serkan PALABIYIK

    2012-06-01

    Full Text Available This paper presents a study on the development of a fuzzy multi-criteria decision-making model for the evaluation of end products of the architectural design process. Potentials of the developed model were investigated within the scope of architectural design education, specifically an international design studio titled “Design for Disassembly and Reuse: Design & Building Multipurpose Transformable Pavilions.” The studio work followed a design process that integrated systematic and heuristic thinking. The design objectives and assessment criteria were clearly set out at the beginning of the process by the studio coordinator with the aim of narrowing the design space and increasing awareness of the consequences of design decisions. At the end of the design process, designs produced in the studio were evaluated using the developed model to support decision making. The model facilitated the identification of positive and negative aspects of the designs and selection of the design alternative that best met the studio objectives set at the beginning.

  20. Analytical Framework for End-to-End Delay Based on Unidirectional Highway Scenario

    Directory of Open Access Journals (Sweden)

    Aslinda Hassan

    2015-01-01

    Full Text Available In a sparse vehicular ad hoc network, a vehicle normally employs a carry and forward approach, where it holds the message it wants to transmit until the vehicle meets other vehicles or roadside units. A number of analyses in the literature have been done to investigate the time delay when packets are being carried by vehicles on both unidirectional and bidirectional highways. However, these analyses are focusing on the delay between either two disconnected vehicles or two disconnected vehicle clusters. Furthermore, majority of the analyses only concentrate on the expected value of the end-to-end delay when the carry and forward approach is used. Using regression analysis, we establish the distribution model for the time delay between two disconnected vehicle clusters as an exponential distribution. Consequently, a distribution is newly derived to represent the number of clusters on a highway using a vehicular traffic model. From there, we are able to formulate end-to-end delay model which extends the time delay model for two disconnected vehicle clusters to multiple disconnected clusters on a unidirectional highway. The analytical results obtained from the analytical model are then validated through simulation results.

  1. Utilizing Domain Knowledge in End-to-End Audio Processing

    DEFF Research Database (Denmark)

    Tax, Tycho; Antich, Jose Luis Diez; Purwins, Hendrik

    2017-01-01

    to learn the commonly-used log-scaled mel-spectrogram transformation. Secondly, we demonstrate that upon initializing the first layers of an end-to-end CNN classifier with the learned transformation, convergence and performance on the ESC-50 environmental sound classification dataset are similar to a CNN......-based model trained on the highly pre-processed log-scaled mel-spectrogram features....

  2. The Levy sections theorem revisited

    International Nuclear Information System (INIS)

    Figueiredo, Annibal; Gleria, Iram; Matsushita, Raul; Silva, Sergio Da

    2007-01-01

    This paper revisits the Levy sections theorem. We extend the scope of the theorem to time series and apply it to historical daily returns of selected dollar exchange rates. The elevated kurtosis usually observed in such series is then explained by their volatility patterns. And the duration of exchange rate pegs explains the extra elevated kurtosis in the exchange rates of emerging markets. In the end, our extension of the theorem provides an approach that is simpler than the more common explicit modelling of fat tails and dependence. Our main purpose is to build up a technique based on the sections that allows one to artificially remove the fat tails and dependence present in a data set. By analysing data through the lenses of the Levy sections theorem one can find common patterns in otherwise very different data sets

  3. The Levy sections theorem revisited

    Science.gov (United States)

    Figueiredo, Annibal; Gleria, Iram; Matsushita, Raul; Da Silva, Sergio

    2007-06-01

    This paper revisits the Levy sections theorem. We extend the scope of the theorem to time series and apply it to historical daily returns of selected dollar exchange rates. The elevated kurtosis usually observed in such series is then explained by their volatility patterns. And the duration of exchange rate pegs explains the extra elevated kurtosis in the exchange rates of emerging markets. In the end, our extension of the theorem provides an approach that is simpler than the more common explicit modelling of fat tails and dependence. Our main purpose is to build up a technique based on the sections that allows one to artificially remove the fat tails and dependence present in a data set. By analysing data through the lenses of the Levy sections theorem one can find common patterns in otherwise very different data sets.

  4. Structure and data requirements of an end-use model for residential ...

    African Journals Online (AJOL)

    driniev

    2004-07-03

    Jul 3, 2004 ... 2 Department of Civil and Urban Engineering, Rand Afrikaans University, PO Box 524, Auckland Park 2006, ... One such approach is end-use modelling, which has a ... chemistry and are not easily removed after being dissolved into the ..... with a rainfall of 12 mm/month for month m the same applies to all.

  5. Numerical Analysis of Flow Field in Generator End-Winding Region

    Directory of Open Access Journals (Sweden)

    Wei Tong

    2008-01-01

    Full Text Available Cooling in an end-winding region of a high-powered, large-sized generator still remains a challenge today because of a number of factors: a larger number of parts/components with irregular geometries, complexity in cooling flow paths, flow splitting and mixing, and interactions between rotor-induced rotating flows and nonrotating flows from stationary sections. One of the key challenges is to model cooling flows passing through armature bars, which are made up of bundles of strands of insulated copper wires and are bent oppositely to cross each other. This work succeeded in modeling a complex generator end-winding region with great efforts to simplify the model by treating the armature bar region as a porous medium. The flow and pressure fields at the end-winding region were investigated numerically using an axial symmetric computational fluid dynamics (CFD model. Based on the analysis, the cooling flow rate at each flow branch (rotor-stator gap, rotor subslot, outside space block, and small ventilation holes to the heat exchanger was determined, and the high-pressure gradient zones were identified. The CFD results have been successfully used to optimize the flow path configuration for improving the generator operation performance, and the control of the cooling flow, as well as minimizing windage losses and flow-introduced noises.

  6. Open-ended education

    DEFF Research Database (Denmark)

    Nørgård, Rikke Toft; Paaskesen, Rikke Berggreen

    2016-01-01

    THE ARTICLE DESCRIBES OPEN-ENDED EDUCATION FOR 21ST CENTURY LEARNING AS THE COMING TOGETHER OF OPEN-ENDED TECHNOLOGY, OPEN-ENDED PROJECTS, AND OPEN-ENDED INSTITUTIONS IN WAYS THAT FOSTER AND PROMOTE FUTURE EDUCATION FOR CITIZENSHIP IN SOCIETY. THROUGH THE CASE OF THE CODING PIRATES FUTURE ISLAND......, THE ARTICLE DEMONSTRATES HOW OPEN-ENDED EDUCATION CAN BE PRACTICED TO FOSTER AND PROMOTE TECHNOLOGICAL IMAGINATION, ENTERPRISING, AND PARTICIPATION. THIS PRACTICE IS THEN DEVELOPED INTO A THEORETICAL MODEL FOR THE CONCEPT OF OPEN-ENDED EDUCATION AS A WAY OF AND FRAMEWORK FOR PRACTICING FUTURE EDUCATION FOR 21......ST CENTURY LEARNING WITH NEW TECHNOLOGIES. THE ARTICLE PRESENTS AN ANSWER TO THE CALL FOR 21ST CENTURY LEARNING AS THOROUGHLY COLLABORATIVE, COMMUNICATIVE, CREATIVE, AND CRITICALLY REFLECTIVE THROUGH THE CASE AND THE CONCEPT OF OPEN-ENDED EDUCATION. IT OUTLINES THE IMPLICATIONS OF THIS CALL...

  7. A model for emergency department end-of-life communications after acute devastating events--part II: moving from resuscitative to end-of-life or palliative treatment.

    Science.gov (United States)

    Limehouse, Walter E; Feeser, V Ramana; Bookman, Kelly J; Derse, Arthur

    2012-11-01

    The model for emergency department (ED) end-of-life communications after acute devastating events addresses decision-making capacity, surrogates, and advance directives, including legal definitions and application of these steps. Part II concerns communications moving from resuscitative to palliative and end-of-life treatments. After completing the steps involved in determining decision-making, emergency physicians (EPs) should consider starting palliative measures versus continuing resuscitative treatment. As communications related to these end-of-life decisions increasingly fall within the scope of emergency medicine (EM) practice, we need to become educated about and comfortable with them. © 2012 by the Society for Academic Emergency Medicine.

  8. 30 CFR 57.19028 - End attachment replacement.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false End attachment replacement. 57.19028 Section 57.19028 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Hoisting Wire Ropes § 57.19028 End attachment replacement. Wire rope attachments shall be replaced when...

  9. 30 CFR 56.19028 - End attachment replacement.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false End attachment replacement. 56.19028 Section 56.19028 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Wire Ropes § 56.19028 End attachment replacement. Wire rope attachments shall be replaced when cracked...

  10. 30 CFR 77.1438 - End attachment replacement.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false End attachment replacement. 77.1438 Section 77.1438 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND... Personnel Hoisting Wire Ropes § 77.1438 End attachment replacement. Wire rope attachments shall be replaced...

  11. Double muscle innervation using end-to-side neurorrhaphy in rats

    Directory of Open Access Journals (Sweden)

    Elisangela Jeronymo Stipp-Brambilla

    Full Text Available CONTEXT AND OBJECTIVE: One of the techniques used for treating facial paralysis is double muscle innervation using end-to-end neurorrhaphy with sectioning of healthy nerves. The aim of this study was to evaluate whether double muscle innervation by means of end-to-side neurorrhaphy could occur, with maintenance of muscle innervation. DESIGN AND SETTING: Experimental study developed at the Experimental Research Center, Faculdade de Medicina de Botucatu, Unesp. METHODS: One hundred rats were allocated to five groups as follows: G1, control group; G2, the peroneal nerve was sectioned; G3, the tibial nerve was transected and the proximal stump was end-to-side sutured to the intact peroneal nerve; G4, 120 days after the G3 surgery, the peroneal nerve was sectioned proximally to the neurorrhaphy; G5, 120 days after the G3 surgery, the peroneal and tibial nerves were sectioned proximally to the neurorrhaphy. RESULTS: One hundred and fifty days after the surgery, G3 did not show any change in tibial muscle weight or muscle fiber diameter, but the axonal fiber diameter in the peroneal nerve distal to the neurorrhaphy had decreased. Although G4 showed atrophy of the cranial tibial muscle 30 days after sectioning the peroneal nerve, the electrophysiological test results and axonal diameter measurement confirmed that muscle reinnervation had occurred. CONCLUSION: These findings suggest that double muscle innervation did not occur through end-to-side neurorrhaphy; the tibial nerve was not able to maintain muscle innervation after the peroneal nerve had been sectioned, although muscle reinnervation was found to have occurred, 30 days after the peroneal nerve had been sectioned.

  12. CASTHY, Statistical Model for Neutron Cross-Sections and Gamma-Ray Spectra

    International Nuclear Information System (INIS)

    Igarasi, Sin-iti; Fukahori, Tokio

    1998-01-01

    Description of program or function: CASTHY calculates neutron cross sections of total, shape elastic scattering and compound nucleus formation with the optical model, and compound elastic, inelastic and capture cross sections by the statistical model. The other cross sections, such as (n,2n), (n,p), (n,f) reactions are treated as cross sections of competing processes, and their sum is given through input data. Capture gamma-ray spectra can also be calculated. The branching ratio for primary transition can be treated in a particular way, if required

  13. Development and testing of the cooling coil cleaning end effector

    International Nuclear Information System (INIS)

    Johnson, K.I.; Mullen, O.D.; Powell, M.R.; Daly, D.S.; Engel, D.W.

    1997-01-01

    The Retrieval Process Development and Enhancement (KPD ampersand E) program has developed and tested an end effector to support the waste retrieval mission at the Idaho National Engineering and Environmental Laboratory (INEEL). The end effector was developed specifically to remove a sticky waste material from the cooling coils in the High Level Liquid Waste (HLLW) tank, and to vacuum up a sediment layer that has settled beneath the cooling coils. An extensive testing program was conducted in the hydraulic test bed (HTB) at the Pacific Northwest National Laboratory (PNNL) to evaluate the performance of the end effector under simulated in-tank conditions. A mock up of the cooling coils was installed in the test bed tank, and simulated waste materials were included to represent the sticky waste on the tubes and the particulate waste settled beneath them. The testing program focused on assessing long-duration mining strategies for cleaning the cooling coils and removing the particulate waste forms. The report describes the results of the end effector testing program at PNNL. Section 2 describes the physical characteristics of the HLLW tanks, including the layout of the cooling coils, and it also describes what is known of the waste forms in the tanks. Section 3 describes the cleaning and retrieval strategy that was used in developing the end effector design. Section 4 describes the cooling coil mockup in the hydraulic test bed. Section 5 discusses the rationale used in selecting the simulants for the tarry waste and particulate waste forms. Section 6 describes the tests that were performed to evaluate cleaning of the cooling coils and retrieval of the particulate simulant. Section 7 summarizes the cleaning and retrieval tests, assesses the relative importance of cleaning the cooling coils and retrieving the particulate waste, and suggests modifications that would simplify the end effector design

  14. The rational choice model in family decision making at the end of life.

    Science.gov (United States)

    Karasz, Alison; Sacajiu, Galit; Kogan, Misha; Watkins, Liza

    2010-01-01

    Most end-of-life decisions are made by family members. Current ethical guidelines for family decision making are based on a hierarchical model that emphasizes the patient's wishes over his or her best interests. Evidence suggests that the model poorly reflects the strategies and priorities of many families. Researchers observed and recorded 26 decision-making meetings between hospital staff and family members. Semi-structured follow-up interviews were conducted. Transcriptions were analyzed using qualitative techniques. For both staff and families, consideration of a patient's best interests generally took priority over the patient's wishes. Staff generally introduced discussion of the patient's wishes for rhetorical purposes, such as persuasion. Competing moral frameworks, which de-emphasized the salience of patients' autonomy and "right to choose," played a role in family decision making. The priority given to the patients' wishes in the hierarchical model does not reflect the priorities of staff and families in making decisions about end-of-life care.

  15. Improving energy efficiency and smart grid program analysis with agent-based end-use forecasting models

    International Nuclear Information System (INIS)

    Jackson, Jerry

    2010-01-01

    Electric utilities and regulators face difficult challenges evaluating new energy efficiency and smart grid programs prompted, in large part, by recent state and federal mandates and financial incentives. It is increasingly difficult to separate electricity use impacts of individual utility programs from the impacts of increasingly stringent appliance and building efficiency standards, increasing electricity prices, appliance manufacturer efficiency improvements, energy program interactions and other factors. This study reviews traditional approaches used to evaluate electric utility energy efficiency and smart-grid programs and presents an agent-based end-use modeling approach that resolves many of the shortcomings of traditional approaches. Data for a representative sample of utility customers in a Midwestern US utility are used to evaluate energy efficiency and smart grid program targets over a fifteen-year horizon. Model analysis indicates that a combination of the two least stringent efficiency and smart grid program scenarios provides peak hour reductions one-third greater than the most stringent smart grid program suggesting that reductions in peak demand requirements are more feasible when both efficiency and smart grid programs are considered together. Suggestions on transitioning from traditional end-use models to agent-based end-use models are provided.

  16. 2010 ANNUAL MEETING ON NUCLEAR TECHNOLOGY. Pt. 4. Section reports

    International Nuclear Information System (INIS)

    Berlepsch, Thilo v.; Hering, Wolfgang

    2011-01-01

    Summary report on 2 Sessions of Section: - New Build and Innovations (Section 12) of the ANNUAL MEETING On NUCLEAR TECHNOLOGY held in Berlin on May 4 to 6, 2010. The other Sections 'Reactor Physics and Methods of Calculation (Section 1)', 'Thermodynamics and Fluid Dynamics (Section 2)', 'Safety of Nuclear Installations - Methods, Analysis, Results (Section 3)', 'Front End and Back End of the Fuel Cycle, Radioactive Waste, Storage (Section 4)', 'Front End of the Fuel Cycle, Fuel Elements and Core Components (Section 5)', 'Operation of Nuclear Installations (Section 6)', 'Decommissioning of Nuclear Installations (Section 7)', 'Fusion Technology (Section 8)', 'Energy Industry and Economics (Section 10)', 'Radiation Protection (Section 11)', 'New Build and Innovations (Session New Build and Innovations, Section 12)', and 'Education, Expert Knowledge, Know-how-Transfer (Section 13)' have been covered in atw issues 10, 11 and 12 (2010). (orig.)

  17. Medical Writing Competency Model - Section 1: Functions, Tasks, and Activities.

    Science.gov (United States)

    Clemow, David B; Wagner, Bertil; Marshallsay, Christopher; Benau, Dan; L'Heureux, Darryl; Brown, David H; Dasgupta, Devjani Ghosh; Girten, Eileen; Hubbard, Frank; Gawrylewski, Helle-Mai; Ebina, Hiroko; Stoltenborg, Janet; York, J P; Green, Kim; Wood, Linda Fossati; Toth, Lisa; Mihm, Michael; Katz, Nancy R; Vasconcelos, Nina-Maria; Sakiyama, Norihisa; Whitsell, Robin; Gopalakrishnan, Shobha; Bairnsfather, Susan; Wanderer, Tatyana; Schindler, Thomas M; Mikyas, Yeshi; Aoyama, Yumiko

    2018-01-01

    This article provides Section 1 of the 2017 Edition 2 Medical Writing Competency Model that describes the core work functions and associated tasks and activities related to professional medical writing within the life sciences industry. The functions in the Model are scientific communication strategy; document preparation, development, and finalization; document project management; document template, standard, format, and style development and maintenance; outsourcing, alliance partner, and client management; knowledge, skill, ability, and behavior development and sharing; and process improvement. The full Model also includes Section 2, which covers the knowledge, skills, abilities, and behaviors needed for medical writers to be effective in their roles; Section 2 is presented in a companion article. Regulatory, publication, and other scientific writing as well as management of writing activities are covered. The Model was developed to aid medical writers and managers within the life sciences industry regarding medical writing hiring, training, expectation and goal setting, performance evaluation, career development, retention, and role value sharing to cross-functional partners.

  18. Predictive Surface Roughness Model for End Milling of Machinable Glass Ceramic

    Energy Technology Data Exchange (ETDEWEB)

    Reddy, M Mohan; Gorin, Alexander [School of Engineering and Science, Curtin University of Technology, Sarawak (Malaysia); Abou-El-Hossein, K A, E-mail: mohan.m@curtin.edu.my [Mechanical and Aeronautical Department, Nelson Mandela Metropolitan University, Port Elegebeth, 6031 (South Africa)

    2011-02-15

    Advanced ceramics of Machinable glass ceramic is attractive material to produce high accuracy miniaturized components for many applications in various industries such as aerospace, electronics, biomedical, automotive and environmental communications due to their wear resistance, high hardness, high compressive strength, good corrosion resistance and excellent high temperature properties. Many research works have been conducted in the last few years to investigate the performance of different machining operations when processing various advanced ceramics. Micro end-milling is one of the machining methods to meet the demand of micro parts. Selecting proper machining parameters are important to obtain good surface finish during machining of Machinable glass ceramic. Therefore, this paper describes the development of predictive model for the surface roughness of Machinable glass ceramic in terms of speed, feed rate by using micro end-milling operation.

  19. Predictive Surface Roughness Model for End Milling of Machinable Glass Ceramic

    International Nuclear Information System (INIS)

    Reddy, M Mohan; Gorin, Alexander; Abou-El-Hossein, K A

    2011-01-01

    Advanced ceramics of Machinable glass ceramic is attractive material to produce high accuracy miniaturized components for many applications in various industries such as aerospace, electronics, biomedical, automotive and environmental communications due to their wear resistance, high hardness, high compressive strength, good corrosion resistance and excellent high temperature properties. Many research works have been conducted in the last few years to investigate the performance of different machining operations when processing various advanced ceramics. Micro end-milling is one of the machining methods to meet the demand of micro parts. Selecting proper machining parameters are important to obtain good surface finish during machining of Machinable glass ceramic. Therefore, this paper describes the development of predictive model for the surface roughness of Machinable glass ceramic in terms of speed, feed rate by using micro end-milling operation.

  20. Studying psychosocial adaptation to end-stage renal disease: the proximal-distal model of health-related outcomes as a base model.

    Science.gov (United States)

    Chan, Ramony; Brooks, Robert; Erlich, Jonathan; Gallagher, Martin; Snelling, Paul; Chow, Josephine; Suranyi, Michael

    2011-05-01

    Studying psychosocial adaptation in end-stage renal disease (ESRD) is increasingly important, as it may explain the variability in health outcomes unaccounted for by clinical factors. The Brenner et al. proximal-distal model of health-related outcomes provides a theoretical foundation for understanding psychosocial adaptation and integrating health outcomes, clinical, and psychosocial factors (Brenner MH, Curbow B, Legro MW. The proximal-distal continuum of multiple health outcome measures: the case of cataract surgery. Med Care. 1995;33(4 Suppl):AS236-44). This study aims to empirically validate the proximal-distal model in the dialysis population and examine the impact of psychosocial factors on the model. A cross-sectional observational study was conducted with a sample of long-term dialysis patients (n=201). Eleven factors: quality of life (QoL), depression, positive affect, comorbidity, symptoms, physical functioning, disease accommodation, loss, self-efficacy, illness acceptance, and social support were measured by standardized psychometric scales. A three-month average of hemoglobin was used. Latent composite structural equation modeling was used to examine the models. The proximal-distal model with slight modification was supported by fit statistics [χ(2)=16.04, df=13, P=.25, root mean square error of approximation (RMSEA)=0.024], indicating that the impact of clinical factors on QoL is mediated through a range of functional and psychological factors, except for hemoglobin which impacts directly on QoL. The model with additional psychosocial factors was also supported by fit statistics (χ(2)=43.59, df=41, P=.36, RMSEA=0.018). These additional factors mainly impact on symptom status, psychological states, and QoL components of the model. The present study supported the proximal-distal model in the dialysis population and demonstrated the considerable impact of psychosocial factors on the model. The proximal-distal model plus psychosocial factors as a

  1. STS/DBS power subsystem end-to-end stability margin

    Science.gov (United States)

    Devaux, R. N.; Vattimo, R. J.; Peck, S. R.; Baker, W. E.

    Attention is given to a full-up end-to-end subsystem stability test which was performed with a flight solar array providing power to a fully operational spacecraft. The solar array simulator is described, and a comparison is made between test results obtained with the simulator and those obtained with the actual array. It is concluded that stability testing with a fully integrated spacecraft is necessary to ensure that all elements have been adequately modeled.

  2. Functional description of APS beamline front ends

    International Nuclear Information System (INIS)

    Kuzay, T.

    1993-02-01

    Traditional synchrotron sources were designed to produce bending magnet radiation and have proven to be an essential scientific tool. Currently, a new generation of synchrotron sources is being built that will be able to accommodate a large number of insertion device (ID) and high quality bending magnet (BM) sources. One example is the 7-GeV Advanced Photon Source (APS) now under construction at Argonne National Laboratory. The research and development effort at the APS is designed to fully develop the potential of this new generation of synchrotron sources. Of the 40 straight sections in the APS storage ring, 34 will be available for IDs. The remaining six sections are reserved for the storage ring hardware and diagnostics. Although the ring incorporates 80 BMs, only 40 of them can be used to extract radiation. The accelerator hardware shadows five of these 40 bending magnets, so the maximum number of BM sources on the lattice is 35. Generally, a photon beamline consists of four functional sections. The first section is the ID or the BM, which provides the radiation source. The second section, which is immediately outside the storage ring but inside a concrete shielding tunnel, is the front end, which is designed to control, define, and/or confine the x-ray beam. In the case of the APS, the front ends are designed to confine the photon beam. The third section, just outside the concrete shielding tunnel and on the experimental floor, is the first optics enclosure, which contains optics to filter and monochromatize the photon beam. The fourth section of a beamline consists of beam transports, additional optics, and experiment stations to do the scientific investigations. This document describes only the front ends of the APS beamlines

  3. SSC collider dipole magnet end mechanical design

    International Nuclear Information System (INIS)

    Delchamps, S.W.; Bossert, R.C.; Carson, J.; Ewald, K.; Fulton, H.; Kerby, J.; Koska, W.; Strait, J.; Wake, M.; Leung, K.K.

    1991-01-01

    This paper describes the mechanical design of the ends of Superconducting Super Collider dipole magnets to be constructed and tested at Fermilab. Coil end clamps, end yoke configuration, and end plate design are discussed. Loading of the end plate by axial Lorentz forces is discussed. Relevant data from 40 mm and 50 mm aperture model dipole magnets built and tested at Fermilab are presented. In particular, the apparent influence of end clamp design on the quench behavior of model SSC dipoles is described

  4. 47 CFR 25.283 - End-of-life disposal.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false End-of-life disposal. 25.283 Section 25.283 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS... satellite orbit under this part shall be relocated, at the end of its useful life, barring catastrophic...

  5. SSC collider dipole magnet end mechanical design

    International Nuclear Information System (INIS)

    Delchamps, S.W.; Bossert, R.C.; Carson, J.; Ewald, K.; Fulton, H.; Kerby, J.; Koska, W.; Strait, J.; Wake, S.M.; Leung, K.K.

    1991-05-01

    This paper describes the mechanical design of the ends of Superconducting Super Collider dipole magnets to be constructed and tested at Fermilab. Coil end clamps, end yoke configuration, and end plate design are discussed. Loading of the end plate by axial Lorentz forces is discussed. Relevant data from 40 mm and 50 mm aperture model dipole magnets built and tested at Fermilab are presented. In particular, the apparent influence of end clamp design on the quench behavior of model SSC dipoles is described. 8 refs., 3 figs

  6. Impact of confinement housing on study end-points in the calf model of cryptosporidiosis.

    Science.gov (United States)

    Graef, Geneva; Hurst, Natalie J; Kidder, Lance; Sy, Tracy L; Goodman, Laura B; Preston, Whitney D; Arnold, Samuel L M; Zambriski, Jennifer A

    2018-04-01

    Diarrhea is the second leading cause of death in children confinement housing, and Interval Collection (IC), which permits use of box stalls. CFC mimics human challenge model methodology but it is unknown if confinement housing impacts study end-points and if data gathered via this method is suitable for generalization to human populations. Using a modified crossover study design we compared CFC and IC and evaluated the impact of housing on study end-points. At birth, calves were randomly assigned to confinement (n = 14) or box stall housing (n = 9), or were challenged with 5 x 107 C. parvum oocysts, and followed for 10 days. Study end-points included fecal oocyst shedding, severity of diarrhea, degree of dehydration, and plasma cortisol. Calves in confinement had no significant differences in mean log oocysts enumerated per gram of fecal dry matter between CFC and IC samples (P = 0.6), nor were there diurnal variations in oocyst shedding (P = 0.1). Confinement housed calves shed significantly more oocysts (P = 0.05), had higher plasma cortisol (P = 0.001), and required more supportive care (P = 0.0009) than calves in box stalls. Housing method confounds study end-points in the calf model of cryptosporidiosis. Due to increased stress data collected from calves in confinement housing may not accurately estimate the efficacy of chemotherapeutics targeting C. parvum.

  7. Are advance directives helpful for good end of life decision making: a cross sectional survey of health professionals.

    Science.gov (United States)

    Peicius, Eimantas; Blazeviciene, Aurelija; Kaminskas, Raimondas

    2017-06-05

    This paper joins the debate over changes in the role of health professionals when applying advance directives to manage the decision-making process at the end of life care. Issues in relation to advance directives occur in clinical units in Lithuania; however, it remains one of the few countries in the European Union (EU) where the discussion on advance directives is not included in the health-care policy-making agenda. To encourage the discussion of advance directives, a study was designed to examine health professionals' understanding and preferences related to advance directives. In addition, the study sought to explore the views of health care professionals of the application of Advance Directives (AD) in clinical practice in Lithuania. A cross-sectional survey was conducted by interviewing 478 health professionals based at major health care centers in Kaunas district, Lithuania. The design of the study included the use of a questionnaire developed for this study and validated by a pilot study. The collected data were analyzed using standard descriptive statistical methods. The analysis of knowledge about AD revealed some statistically significant differences when comparing the respondents' profession and gender. The analysis also indicated key emerging themes among respondents including tranquility of mind, the longest possible life expectancy and freedom of choice. Further, the study findings revealed that more than half of the study participants preferred to express their will while alive by using advance directives. The study findings revealed a low level of knowledge on advance directives among health professionals. Most health professionals agreed that AD's improved end-of-life decision making while the majority of physicians appreciated AD as the best tool for sharing responsibilities in clinical practice in Lithuania. More physicians than nurses preferred the presence of advance directives to support their decision making in end-of-life situations.

  8. Towards an energy end use model

    International Nuclear Information System (INIS)

    Smith Fontana, Raul

    2003-01-01

    The general equilibrium energy end use model proposed, uses linear programming as te basic and central element to optimization of variables defined in the economic and energy areas of the country related to a four factors structure: Energy, Raw Material, Capital and Labor, and related to the sectors: Residential, Commercial, Industrial, Transportation and Import/Export. Input-Output coefficients are defined in an input-output matrix of processes representing the supply of Electricity (generated by nuclear- not available in Chile-hydro, gas, fuel-oil and coal), Petroleum, Imported Natural Gas (transported and distributed) National Natural Gas, LPG, Coal, Wood and representing a demand of Residential, Commercial, Industrial, Transportation and Import/Export. There is an interaction of the final demand composition, the prices of capital, labor and taxes with the levels of operation for each process and the prices of goods and services. In addition to the prices of fuels for each annual period, to the supply and demand of energy and to the total demand it can forecast the optimum coefficients of the final demand. If the data to be collected result reasonably complete and consistent, the model will be useful for planning. A special effort should be placed in specifying a certain number of typical energy activities, the available options for fuels, the selection of them attending rational market decisions and conservation according to well known economical criteria of substitution. To simulate the process of options selection given by the activities and to allow substitutions, it is possible to introduce the logit function characterized by a Weibull distribution and the generalized substitution function characterized by the constant electricity. The model would allow, assuming differents scenario, to visualize general policies in the penetration of energy technologies. To study the penetration of electric energy generated by nuclear, in which the country does not have

  9. End-to-end simulation of the C-ADS injector Ⅱ with a 3-D field map

    International Nuclear Information System (INIS)

    Wang Zhijun; He Yuan; Li Chao; Wang Wangsheng; Liu Shuhui; Jia Huan; Xu Xianbo; Chen Ximeng

    2013-01-01

    The Injector II, one of the two parallel injectors of the high-current superconducting proton driver linac for the China Accelerator-Driven System (C-ADS) project, is being designed and constructed by the Institute of Modern Physics. At present, the design work for the injector is almost finished. End-to-end simulation has been carried out using the TRACK multiparticle simulation code to check the match between each acceleration section and the performance of the injector as a whole. Moreover, multiparticle simulations with all kinds of errors and misalignments have been performed to define the requirements of each device. The simulation results indicate that the lattice design is robust. In this paper, the results of end-to-end simulation and error simulation with a 3-D field map are presented. (authors)

  10. 20 CFR 416.1832 - When we consider your marriage ended.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false When we consider your marriage ended. 416.1832 Section 416.1832 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SUPPLEMENTAL SECURITY INCOME... consider your marriage ended. We consider your marriage ended when— (a) Your spouse dies; (b) Your divorce...

  11. The Glauber model and heavy ion reaction and elastic scattering cross sections

    Energy Technology Data Exchange (ETDEWEB)

    Mehndiratta, Ajay [Physics Department, Indian Institute of Technology, Guwahati (India); Shukla, Prashant, E-mail: pshukla@barc.gov.in [Nuclear Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Homi Bhabha National Institute, Anushakti Nagar, Mumbai 400094 (India)

    2017-05-15

    We revisit the Glauber model to study the heavy ion reaction cross sections and elastic scattering angular distributions at low and intermediate energies. The Glauber model takes nucleon–nucleon cross sections and nuclear densities as inputs and has no free parameter and thus can predict the cross sections for unknown systems. The Glauber model works at low energies down to Coulomb barrier with very simple modifications. We present new parametrization of measured total cross sections as well as ratio of real to imaginary parts of the scattering amplitudes for pp and np collisions as a function of nucleon kinetic energy. The nuclear (charge) densities obtained by electron scattering form factors measured in large momentum transfer range are used in the calculations. The heavy ion reaction cross sections are calculated for light and heavy systems and are compared with available data measured over large energy range. The model gives excellent description of the data. The elastic scattering angular distributions are calculated for various systems at different energies. The model gives good description of the data at small momentum transfer but the calculations deviate from the data at large momentum transfer.

  12. Progress report of the Radiation Technology and Industrial Applications Section, Isotope Group for the period ending August 1977

    International Nuclear Information System (INIS)

    Naik, A.D.; Roy, A.N.; Majali, A.B.

    1977-01-01

    The activities of the Radiation Technology and Industrial Applications Section of the Bhabha Atomic Research Centre, Bombay, for the period ending August 1977 are reported. Major highlights are: (1) completion of studies and design engineering for an economic scale cobalt-60 based irradiator for the radiation sterilisation of medical products, (2) taking up the work of setting up the cobalt-60 irradiation facilities for sources up to 300,000 Ci level, (3) development of radiation processed wood-polymer composite and practical demonstration of its superiority for application in industries - a cobalt-60 facility specifically for this purpose is being installed, (4) development of a commercially viable design of a smoke alarm system based on radioisotopes and (5) production and supply of irradiation units such as gamma chambers, radiography cameras, etc. (M.G.B.)

  13. 17 CFR 230.498 - Summary Prospectuses for open-end management investment companies.

    Science.gov (United States)

    2010-04-01

    ...-end management investment companies. 230.498 Section 230.498 Commodity and Securities Exchanges... management investment companies. (a) Definitions. For purposes of this section: (1) Class means a class of... reliance on an exemptive rule adopted by the Commission. (3) Fund means an open-end management investment...

  14. Sectional modeling of nanoparticle size and charge distributions in dusty plasmas

    International Nuclear Information System (INIS)

    Agarwal, Pulkit; Girshick, Steven L

    2012-01-01

    Sectional models of the dynamics of aerosol populations are well established in the aerosol literature but have received relatively less attention in numerical models of dusty plasmas, where most modeling studies have assumed the existence of monodisperse dust particles. In the case of plasmas in which nanoparticles nucleate and grow, significant polydispersity can exist in particle size distributions, and stochastic charging can cause particles of given size to have a broad distribution of charge states. Sectional models, while computationally expensive, are well suited to treating such distributions. This paper presents an overview of sectional modeling of nanodusty plasmas, and presents examples of simulation results that reveal important qualitative features of the spatiotemporal evolution of such plasmas, many of which could not be revealed by models that consider only monodisperse dust particles and average particle charge. These features include the emergence of bimodal particle populations consisting of very small neutral particles and larger negatively charged particles, the effects of size and charge distributions on coagulation, spreading and structure of the particle cloud, and the dynamics of dusty plasma afterglows. (paper)

  15. FMIT test-end instrumentation development bases

    International Nuclear Information System (INIS)

    Fuller, J.L.

    1982-06-01

    FMIT test-end measurements proposed for deuteron beam control, target diagnostics, and irradiation sample dosimetry are listed. The test-end refers to the area inside the test cell, but includes measurements inside and outside the cell. Justification, categorization, and limits qualification are presented for each measurement. Methods are purposefully de-emphasized in order to clarify the measurement needs, not techniques. Some discussion of techniques currently under investigation is given in the last section of the report

  16. Integral formula for elliptic SOS models with domain walls and a reflecting end

    Energy Technology Data Exchange (ETDEWEB)

    Lamers, Jules, E-mail: j.lamers@uu.nl

    2015-12-15

    In this paper we extend previous work of Galleas and the author to elliptic SOS models. We demonstrate that the dynamical reflection algebra can be exploited to obtain a functional equation characterizing the partition function of an elliptic SOS model with domain-wall boundaries and one reflecting end. Special attention is paid to the structure of the functional equation. Through this approach we find a novel multiple-integral formula for that partition function.

  17. A housing stock model of non-heating end-use energy in England verified by aggregate energy use data

    International Nuclear Information System (INIS)

    Lorimer, Stephen

    2012-01-01

    This paper proposes a housing stock model of non-heating end-use energy for England that can be verified using aggregate energy use data available for small areas. These end-uses, commonly referred to as appliances and lighting, are a rapidly increasing part of residential energy demand. This paper proposes a model that can be verified using aggregated data of electricity meters in small areas and census data on housing. Secondly, any differences that open up between major collections of housing could potentially be resolved by using data from frequently updated expenditure surveys. For the year 2008, the model overestimated domestic non-heating energy use at the national scale by 1.5%. This model was then used on the residential sector with various area classifications, which found that rural and suburban areas were generally underestimated by up to 3.3% and urban areas overestimated by up to 5.2% with the notable exception of “professional city life” classifications. The model proposed in this paper has the potential to be a verifiable and adaptable model for non-heating end-use energy in households in England for the future. - Highlights: ► Housing stock energy model was developed for end-uses outside of heating for UK context. ► This entailed changes to the building energy model that serves as the bottom of the stock model. ► The model is adaptable to reflect rapid changes in consumption between major housing surveys. ► Verification was done against aggregated consumption data and for the first time uses a measured size of the housing stock. ► The verification process revealed spatial variations in consumption patterns for future research.

  18. Use of nuclear reaction models in cross section calculations

    International Nuclear Information System (INIS)

    Grimes, S.M.

    1975-03-01

    The design of fusion reactors will require information about a large number of neutron cross sections in the MeV region. Because of the obvious experimental difficulties, it is probable that not all of the cross sections of interest will be measured. Current direct and pre-equilibrium models can be used to calculate non-statistical contributions to neutron cross sections from information available from charged particle reaction studies; these are added to the calculated statistical contribution. Estimates of the reliability of such calculations can be derived from comparisons with the available data. (3 tables, 12 figures) (U.S.)

  19. End-to-end operations at the National Radio Astronomy Observatory

    Science.gov (United States)

    Radziwill, Nicole M.

    2008-07-01

    In 2006 NRAO launched a formal organization, the Office of End to End Operations (OEO), to broaden access to its instruments (VLA/EVLA, VLBA, GBT and ALMA) in the most cost-effective ways possible. The VLA, VLBA and GBT are mature instruments, and the EVLA and ALMA are currently under construction, which presents unique challenges for integrating software across the Observatory. This article 1) provides a survey of the new developments over the past year, and those planned for the next year, 2) describes the business model used to deliver many of these services, and 3) discusses the management models being applied to ensure continuous innovation in operations, while preserving the flexibility and autonomy of telescope software development groups.

  20. 49 CFR 238.409 - Forward end structures of power car cabs.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Forward end structures of power car cabs. 238.409... II Passenger Equipment § 238.409 Forward end structures of power car cabs. This section contains requirements for the forward end structure of the cab of a power car. (A conceptual implementation of this end...

  1. Soft modes at the critical end point in the chiral effective models

    International Nuclear Information System (INIS)

    Fujii, Hirotsugu; Ohtani, Munehisa

    2004-01-01

    At the critical end point in QCD phase diagram, the scalar, vector and entropy susceptibilities are known to diverge. The dynamic origin of this divergence is identified within the chiral effective models as softening of a hydrodynamic mode of the particle-hole-type motion, which is a consequence of the conservation law of the baryon number and the energy. (author)

  2. End-to-side neurorraphy: a long-term study of neural regeneration in a rat model.

    Science.gov (United States)

    Tarasidis, G; Watanabe, O; Mackinnon, S E; Strasberg, S R; Haughey, B H; Hunter, D A

    1998-10-01

    This study evaluated long-term reinnervation of an end-to-side neurorraphy and the resultant functional recovery in a rat model. The divided distal posterior tibial nerve was repaired to the side of an intact peroneal nerve. Control groups included a cut-and-repair of the posterior tibial nerve and an end-to-end repair of the peroneal nerve to the posterior tibial nerve. Evaluations included walking-track analysis, nerve conduction studies, muscle mass measurements, retrograde nerve tracing, and histologic evaluation. Walking tracks indicated poor recovery of posterior tibial nerve function in the experimental group. No significant difference in nerve conduction velocities was seen between the experimental and control groups. Gastrocnemius muscle mass measurements revealed no functional recovery in the experimental group. Similarly, retrograde nerve tracing revealed minimal motor neuron staining in the experimental group. However, some sensory staining was seen within the dorsal root ganglia of the end-to-side group. Histologic study revealed minimal myelinated axonal regeneration in the experimental group as compared with findings in the other groups. These results suggest that predominantly sensory regeneration occurs in an end-to-side neurorraphy at an end point of 6 months.

  3. Model Test Research on the End Bearing Behavior of the Large-Diameter Cast-in-Place Concrete Pile for Jointed Rock Mass

    Directory of Open Access Journals (Sweden)

    Jingwei Cai

    2016-01-01

    Full Text Available For large-diameter, cast-in-place concrete piles, the end bearing capacity of a single pile is affected by discontinuous surfaces that exist in natural rock masses when the bearing layer of the pile end is located in the rock layer. In order to study the influence of the jointed dip angle on the bearing characteristics of the pile end, the discrete element models are adopted to simulate the mechanical characteristics of the jointed rock masses, and the model tests of the failure mode of the jointed rock masses were also designed. The results of the numerical calculations and modeling tests show that the joints, which have a filtering effect on the internal stress of the bedrock located at the pile end, change the load transferring paths. And the failure mode of the jointed rock foundation also changes as jointed dip angle changes. The rock located at the pile end generally presents a wedge failure mode. In addition, the Q-S curves obtained by model tests show that the ultimate end bearing capacity of a single pile is influenced by the jointed dip angle. The above results provide an important theoretical basis for how to correctly calculate end resistance for a cast-in-place concrete pile.

  4. Understanding Effect of Constraint Release Environment on End-to-End Vector Relaxation of Linear Polymer Chains

    KAUST Repository

    Shivokhin, Maksim E.

    2017-05-30

    We propose and verify methods based on the slip-spring (SSp) model [ Macromolecules 2005, 38, 14 ] for predicting the effect of any monodisperse, binary, or ternary environment of topological constraints on the relaxation of the end-to-end vector of a linear probe chain. For this purpose we first validate the ability of the model to consistently predict both the viscoelastic and dielectric response of monodisperse and binary mixtures of type A polymers, based on published experimental data. We also report the synthesis of new binary and ternary polybutadiene systems, the measurement of their linear viscoelastic response, and the prediction of these data by the SSp model. We next clarify the relaxation mechanisms of probe chains in these constraint release (CR) environments by analyzing a set of "toy" SSp models with simplified constraint release rates, by examining fluctuations of the end-to-end vector. In our analysis, the longest relaxation time of the probe chain is determined by a competition between the longest relaxation times of the effective CR motions of the fat and thin tubes and the motion of the chain itself in the thin tube. This picture is tested by the analysis of four model systems designed to separate and estimate every single contribution involved in the relaxation of the probe\\'s end-to-end vector in polydisperse systems. We follow the CR picture of Viovy et al. [ Macromolecules 1991, 24, 3587 ] and refine the effective chain friction in the thin and fat tubes based on Read et al. [ J. Rheol. 2012, 56, 823 ]. The derived analytical equations form a basis for generalizing the proposed methodology to polydisperse mixtures of linear and branched polymers. The consistency between the SSp model and tube model predictions is a strong indicator of the compatibility between these two distinct mesoscopic frameworks.

  5. Model of passage of vessels through the waterway section forming the schedule in the course of its implementation

    Directory of Open Access Journals (Sweden)

    S. N. Plotnikov

    2017-01-01

    Full Text Available The model of passage of vessels through a section of the waterway is considered, which independently determines the order of passage of vessels with limited capacity of sections of the track. Such a model will consist of a number of standard algorithmic networks. When composing the schedule in the model, the following preference rules were used: first-come-first-served (that is, if the ship occupied the workplace, this decision is not canceled; The rule of the shortest operation; For the swamps the priority of vessels going downstream (the direction of flow from the source to the drain. An algorithmic network that implements the search for an acceptable schedule must implement the following for conflicting operations: the operation that has started is not interrupted; If several operations simultaneously claim for one workplace (port, reach and their number is greater than its throughput, then the conflict resolution is carried out in accordance with predefined preference rules or based on the user's decision; If the operation is waiting for the release of the workplace, it does not occupy the resource; The resource is returned immediately after the operation is completed. The considered design of algorithmic networks allows to resolve the conflict, with a simultaneous resource request, to take the resource once, remember that it was received and return it after the end of the operation, then the resource receives a contra-controlling operation for execution. However, the use of this design introduces redundancy into the model, even if it is used only for conflicting operations. The model is presented in the language of algorithmic networks and is implemented in the system of modeling automation KOGNITRON.

  6. Mercury anomalies as a proxy for large igneous province volicanism and effects on the carbon cycle in a U-Pb age-constrained section spanning the end-Triassic mass extinction, Levanto, Peru

    Science.gov (United States)

    Yager, J. A.; West, A. J.; Bergquist, B. A.; Thibodeau, A. M.; Corsetti, F. A.; Berelson, W.; Rosas, S.; Bottjer, D. J.

    2017-12-01

    Understanding the causes of the end-Triassic extinction and their potential relationship to Central Atlantic Magmatic Province (CAMP) volcanism necessitates careful correlation of carbon cycle records (largely from marine sections) and volcanism (largely from terrestrial successions) in a robust chronological framework. Here, we report stable carbon isotopes and mercury concentrations and isotopes from the Levanto section in Northern Peru as a putative proxy for CAMP (a large igneous province) in a marine section. Levanto represents deposition well below storm wave base and is lithologically homogenous before, during, and after the end-Triassic extinction interval, making it ideal for detailed chemostratigraphy. Furthermore, abundant intercalated ash beds allow us to correlate mercury concentrations in the marine record directly with CAMP basalt ages, providing a test of the correspondence of mercury anomalies with the eruption of CAMP volcanics. Age dating and C isotope analyses provide an opportunity to explore orbital tuning of the carbon isotope record and ground truth it with existing U-Pb ages from the section, a feature not available in any other marine sections examined to date. The abundance of U-Pb dated ashes in the Levanto section allows us to correlate orbital tuning with other basins, which lack absolute age control, providing a better understanding for the C cycle changes associated with the Triassic-Jurassic boundary.

  7. Report on the value engineering workshop on APS beamline front ends

    International Nuclear Information System (INIS)

    Kuzay, T.

    1993-01-01

    A formal value engineering evaluation process was developed to address the front end components of the beamlines for the Advanced Photon Source (APS). This process (described in Section 2) involved an information phase, a creative phase, a judgment phase, a development phase, and a recommendation phase. Technical experts from other national laboratories and industry were invited to a two-day Value Engineering Workshop on November 5-6, 1992. The results of this Workshop are described in Section 4. Following the Workshop, various actions by the APS staff led to the redesign of the front end components, which are presented in Sections 5 and 6. The cost benefit analysis is presented in Section 7. It is important of realize that an added benefit of the Workshop was to obtain numerous design evaluations and enhancements of the front end components by experts in the field. As the design work proceeds to Title II completion, the APS staff is including many of these suggestions

  8. Lidar cross-sections of soot fractal aggregates: Assessment of equivalent-sphere models

    Science.gov (United States)

    Ceolato, Romain; Gaudfrin, Florian; Pujol, Olivier; Riviere, Nicolas; Berg, Matthew J.; Sorensen, Christopher M.

    2018-06-01

    This work assesses the ability of equivalent-sphere models to reproduce the optical properties of soot aggregates relevant for lidar remote sensing, i.e. the backscattering and extinction cross sections. Lidar cross-sections are computed with a spectral discrete dipole approximation model over the visible-to-infrared (400-5000 nm) spectrum and compared with equivalent-sphere approximations. It is shown that the equivalent-sphere approximation, applied to fractal aggregates, has a limited ability to calculate such cross-sections well. The approximation should thus be used with caution for the computation of broadband lidar cross-sections, especially backscattering, at small and intermediate wavelengths (e.g. UV to visible).

  9. End-to-end delay analysis in wireless sensor networks with service vacation

    KAUST Repository

    Alabdulmohsin, Ibrahim; Hyadi, Amal; Afify, Laila H.; Shihada, Basem

    2014-01-01

    In this paper, a delay-sensitive multi-hop wireless sensor network is considered, employing an M/G/1 with vacations framework. Sensors transmit measurements to a predefined data sink subject to maximum end-to-end delay constraint. In order to prolong the battery lifetime, a sleeping scheme is adopted throughout the network nodes. The objective of our proposed framework is to present an expression for maximum hop-count as well as an approximate expression of the probability of blocking at the sink node upon violating certain end-to-end delay threshold. Using numerical simulations, we validate the proposed analytical model and demonstrate that the blocking probability of the system for various vacation time distributions matches the simulation results.

  10. End-to-end delay analysis in wireless sensor networks with service vacation

    KAUST Repository

    Alabdulmohsin, Ibrahim

    2014-04-01

    In this paper, a delay-sensitive multi-hop wireless sensor network is considered, employing an M/G/1 with vacations framework. Sensors transmit measurements to a predefined data sink subject to maximum end-to-end delay constraint. In order to prolong the battery lifetime, a sleeping scheme is adopted throughout the network nodes. The objective of our proposed framework is to present an expression for maximum hop-count as well as an approximate expression of the probability of blocking at the sink node upon violating certain end-to-end delay threshold. Using numerical simulations, we validate the proposed analytical model and demonstrate that the blocking probability of the system for various vacation time distributions matches the simulation results.

  11. Anchorage strength models for end-debonding predictions in RC beams strengthened with FRP composites

    Science.gov (United States)

    Nardini, V.; Guadagnini, M.; Valluzzi, M. R.

    2008-05-01

    The increase in the flexural capacity of RC beams obtained by externally bonding FRP composites to their tension side is often limited by the premature and brittle debonding of the external reinforcement. An in-depth understanding of this complex failure mechanism, however, has not yet been achieved. With specific regard to end-debonding failure modes, extensive experimental observations reported in the literature highlight the important distinction, often neglected in strength models proposed by researchers, between the peel-off and rip-off end-debonding types of failure. The peel-off failure is generally characterized by a failure plane located within the first few millimetres of the concrete cover, whilst the rip-off failure penetrates deeper into the concrete cover and propagates along the tensile steel reinforcement. A new rip-off strength model is described in this paper. The model proposed is based on the Chen and Teng peel-off model and relies upon additional theoretical considerations. The influence of the amount of the internal tensile steel reinforcement and the effective anchorage length of FRP are considered and discussed. The validity of the new model is analyzed further through comparisons with test results, findings of a numerical investigation, and a parametric study. The new rip-off strength model is assessed against a database comprising results from 62 beams tested by various researchers and is shown to yield less conservative results.

  12. HINS Linac front end focusing system R&D

    Energy Technology Data Exchange (ETDEWEB)

    Apollinari, G.; Carcagno, R.H.; Dimarco, J.; Huang, Y.; Kashikhin, V.V.; Orris, D.F.; Page, T.M.; Rabehl, R.; Sylvester, C.; Tartaglia, M.A.; Terechkine, I.; /Fermilab /Argonne

    2008-08-01

    This report summarizes current status of an R&D program to develop a focusing system for the front end of a superconducting RF linac. Superconducting solenoids will be used as focusing lenses in the low energy accelerating sections of the front end. The development of focusing lenses for the first accelerating section is in the production stage, and lens certification activities are in preparation at FNAL. The report contains information about the focusing lens design and performance, including solenoid, dipole corrector, and power leads, and about cryogenic system design and performance. It also describes the lens magnetic axis position measurement technique and discusses scope of an acceptance/certification process.

  13. Predictive model for risk of cesarean section in pregnant women after induction of labor.

    Science.gov (United States)

    Hernández-Martínez, Antonio; Pascual-Pedreño, Ana I; Baño-Garnés, Ana B; Melero-Jiménez, María R; Tenías-Burillo, José M; Molina-Alarcón, Milagros

    2016-03-01

    To develop a predictive model for risk of cesarean section in pregnant women after induction of labor. A retrospective cohort study was conducted of 861 induced labors during 2009, 2010, and 2011 at Hospital "La Mancha-Centro" in Alcázar de San Juan, Spain. Multivariate analysis was used with binary logistic regression and areas under the ROC curves to determine predictive ability. Two predictive models were created: model A predicts the outcome at the time the woman is admitted to the hospital (before the decision to of the method of induction); and model B predicts the outcome at the time the woman is definitely admitted to the labor room. The predictive factors in the final model were: maternal height, body mass index, nulliparity, Bishop score, gestational age, macrosomia, gender of fetus, and the gynecologist's overall cesarean section rate. The predictive ability of model A was 0.77 [95% confidence interval (CI) 0.73-0.80] and model B was 0.79 (95% CI 0.76-0.83). The predictive ability for pregnant women with previous cesarean section with model A was 0.79 (95% CI 0.64-0.94) and with model B was 0.80 (95% CI 0.64-0.96). For a probability of estimated cesarean section ≥80%, the models A and B presented a positive likelihood ratio (+LR) for cesarean section of 22 and 20, respectively. Also, for a likelihood of estimated cesarean section ≤10%, the models A and B presented a +LR for vaginal delivery of 13 and 6, respectively. These predictive models have a good discriminative ability, both overall and for all subgroups studied. This tool can be useful in clinical practice, especially for pregnant women with previous cesarean section and diabetes.

  14. Non-random temporary emigration and the robust design: Conditions for bias at the end of a time series: Section VIII

    Science.gov (United States)

    Langtimm, Catherine A.

    2008-01-01

    Deviations from model assumptions in the application of capture–recapture models to real life situations can introduce unknown bias. Understanding the type and magnitude of bias under these conditions is important to interpreting model results. In a robust design analysis of long-term photo-documented sighting histories of the endangered Florida manatee, I found high survival rates, high rates of non-random temporary emigration, significant time-dependence, and a diversity of factors affecting temporary emigration that made it difficult to model emigration in any meaningful fashion. Examination of the time-dependent survival estimates indicated a suspicious drop in survival rates near the end of the time series that persisted when the original capture histories were truncated and reanalyzed under a shorter time frame. Given the wide swings in manatee emigration estimates from year to year, a likely source of bias in survival was the convention to resolve confounding of the last survival probability in a time-dependent model with the last emigration probabilities by setting the last unmeasurable emigration probability equal to the previous year’s probability when the equality was actually false. Results of a series of simulations demonstrated that if the unmeasurable temporary emigration probabilities in the last time period were not accurately modeled, an estimation model with significant annual variation in survival probabilities and emigration probabilities produced bias in survival estimates at the end of the study or time series being explored. Furthermore, the bias propagated back in time beyond the last two time periods and the number of years affected varied positively with survival and emigration probabilities. Truncating the data to a shorter time frame and reanalyzing demonstrated that with additional years of data surviving temporary emigrants eventually return and are detected, thus in subsequent analysis unbiased estimates are eventually realized.

  15. A cosmological model with compact space sections and low mass density

    International Nuclear Information System (INIS)

    Fagundes, H.V.

    1982-01-01

    A general relativistic cosmological model is presented, which has closed space sections and mass density below a critical density similar to that of Friedmann's models. The model may predict double images of cosmic sources. (Author) [pt

  16. Contribution to the optical model study by the measurement of the reaction sections; Contribution au modele optique par la mesure de sections de reaction

    Energy Technology Data Exchange (ETDEWEB)

    Delaunay, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1967-07-01

    Excitation functions of reaction cross-section {delta}{sub R} for protons were obtained between 5 and 11 MeV, for {sup 141}Pr and {sup 150}Nd by radioactive techniques and, between 9 and 12 MeV, for Cu and Ni by the transmission method. Results were compared to the prevision of the optical model. Calculations were made to see in what part {delta}{sub R} is able to reduce the ambiguities of the optical model. (author) [French] Des fonctions d'excitation de section efficace de reaction par protons {delta}{sub R} ont ete obtenues pour {sup 141}Pr et {sup 150}Nd, entre 5 et 11 MeV, par des methodes de radioactivite et pour Cu et Ni, entre 9 et 12 MeV, par la methode de transmission. Les resultats ont ete compares aux previsions du modele optique. Des calculs ont ete faits pour voir le role que peut jouer {delta}{sub R} pour diminuer les differentes ambiguites du modele optique. (auteur)

  17. End-to-End Adversarial Retinal Image Synthesis.

    Science.gov (United States)

    Costa, Pedro; Galdran, Adrian; Meyer, Maria Ines; Niemeijer, Meindert; Abramoff, Michael; Mendonca, Ana Maria; Campilho, Aurelio

    2018-03-01

    In medical image analysis applications, the availability of the large amounts of annotated data is becoming increasingly critical. However, annotated medical data is often scarce and costly to obtain. In this paper, we address the problem of synthesizing retinal color images by applying recent techniques based on adversarial learning. In this setting, a generative model is trained to maximize a loss function provided by a second model attempting to classify its output into real or synthetic. In particular, we propose to implement an adversarial autoencoder for the task of retinal vessel network synthesis. We use the generated vessel trees as an intermediate stage for the generation of color retinal images, which is accomplished with a generative adversarial network. Both models require the optimization of almost everywhere differentiable loss functions, which allows us to train them jointly. The resulting model offers an end-to-end retinal image synthesis system capable of generating as many retinal images as the user requires, with their corresponding vessel networks, by sampling from a simple probability distribution that we impose to the associated latent space. We show that the learned latent space contains a well-defined semantic structure, implying that we can perform calculations in the space of retinal images, e.g., smoothly interpolating new data points between two retinal images. Visual and quantitative results demonstrate that the synthesized images are substantially different from those in the training set, while being also anatomically consistent and displaying a reasonable visual quality.

  18. System of end-to-end symmetric database encryption

    Science.gov (United States)

    Galushka, V. V.; Aydinyan, A. R.; Tsvetkova, O. L.; Fathi, V. A.; Fathi, D. V.

    2018-05-01

    The article is devoted to the actual problem of protecting databases from information leakage, which is performed while bypassing access control mechanisms. To solve this problem, it is proposed to use end-to-end data encryption, implemented at the end nodes of an interaction of the information system components using one of the symmetric cryptographic algorithms. For this purpose, a key management method designed for use in a multi-user system based on the distributed key representation model, part of which is stored in the database, and the other part is obtained by converting the user's password, has been developed and described. In this case, the key is calculated immediately before the cryptographic transformations and is not stored in the memory after the completion of these transformations. Algorithms for registering and authorizing a user, as well as changing his password, have been described, and the methods for calculating parts of a key when performing these operations have been provided.

  19. [End-of-life care and end-of-life medical decisions: the ITAELD study].

    Science.gov (United States)

    Miccinesi, Guido; Puliti, Donella; Paci, Eugenio

    2011-01-01

    To describe the attitudes towards end of life care and the practice of end-of-life medical decisions with possible life-shortening effect among Italian physicians. Cross sectional study (last death among the assisted patients in the last 12 months was considered). In the year 2007, 5,710 GPs and 8,950 hospital physicians were invited all over Italy to participate in the ITAELDstudy through anonymous mail questionnaire. Proportion of agreement with statements on end-of-life care issues. Proportion of deaths with an end-of-life medical decision. The response rate was 19.2%. The 65% of respondents agreed with the duty to respect any non-treatment request of the competent patient, the 55% agreed with the same duty in case of advanced directives, the 39% in case of proxy's request. The 53% of respondents agreed with the ethical acceptability of active euthanasia in selected cases. Among 1,850 deaths the 57.7% did not receive any end-of-life medical decision. For a further 21.0% no decision was possible, being sudden and unexpected deaths. In the remaining 21.3% at least one end-of-life medical decision was reported: 0.8% was classified as physician assisted death, 20.5% as non-treatment decision. Among all deceased the 19.6% were reported to have been deeply sedated. Being favourable to the use of opioids in terminal patients was associated to non-treatment decisions with possible but non-intentional life shortening effect; agreeing with the duty to fully respect any actual non-treatment request of the competent patient was associated to end-of life medical decisions with intentional life-shortening effect (adjusted OR>10 in both cases). The life stance and ethical beliefs of physicians determine their behaviour at the end of life wherever specific statements of law are lacking. Therefore education and debate are needed on these issues.

  20. Ending domestic violence against women: assessment of ...

    African Journals Online (AJOL)

    Ending domestic violence against women: assessment of knowledge and ... Methods: A descriptive cross-sectional design was utilized for this study. ... study documented poor knowledge and perception of DV among the studied population.

  1. Older Adults Making End of Life Decisions: An Application of Roy's Adaptation Model

    Directory of Open Access Journals (Sweden)

    Weihua Zhang

    2013-01-01

    Full Text Available Purpose. The purpose of this study was to identify variables that influenced completion of advanced directives in the context of adaptation from national data in older adults. Knowledge gained from this study would help us identify factors that might influence end of life discussions and shed light on strategies on effective communication on advance care planning. Design and Method. A model-testing design and path analysis were used to examine secondary data from 938 participants. Items were extracted from the data set to correspond to variables for this study. Scales were constructed and reliabilities were tested. Results. The final path model showed that physical impairment, self-rated health, continuing to work, and family structure had direct and indirect effects on completion of advanced directives. Five percent of the variance was accounted for by the path analysis. Conclusion. The variance accounted for by the model was small. This could have been due to the use of secondary data and limitations imposed for measurement. However, health care providers and families should explore patient’s perception of self-health as well as their family and work situation in order to strategize a motivational discussion on advance directive or end of life care planning.

  2. Covariance matrices for nuclear cross sections derived from nuclear model calculations

    International Nuclear Information System (INIS)

    Smith, D. L.

    2005-01-01

    The growing need for covariance information to accompany the evaluated cross section data libraries utilized in contemporary nuclear applications is spurring the development of new methods to provide this information. Many of the current general purpose libraries of evaluated nuclear data used in applications are derived either almost entirely from nuclear model calculations or from nuclear model calculations benchmarked by available experimental data. Consequently, a consistent method for generating covariance information under these circumstances is required. This report discusses a new approach to producing covariance matrices for cross sections calculated using nuclear models. The present method involves establishing uncertainty information for the underlying parameters of nuclear models used in the calculations and then propagating these uncertainties through to the derived cross sections and related nuclear quantities by means of a Monte Carlo technique rather than the more conventional matrix error propagation approach used in some alternative methods. The formalism to be used in such analyses is discussed in this report along with various issues and caveats that need to be considered in order to proceed with a practical implementation of the methodology

  3. Modeling Soft Gluons and Fiducial Cross Sections: New Physics or Old QCD?

    CERN Multimedia

    CERN. Geneva

    2014-01-01

    In this talk I will describe some of the consequences of the consistently discrepant WW cross section measured at ATLAS and CMS. I will describe models where stops can be as light as 200 GeV satisfying naturalness constraints. I will also discuss the current states of the art modeling of QCD effects in the measurement of the cross section using p_T resummation. I will show that there is a sizable effect caused by a jet veto in extrapolating to the total cross section, but ultimately not enough to explain the current discrepancy.

  4. Joint research report of Central Research Institute of Electric Power Industry and Japan Research Institute Ltd. Conceptual construction of Japanese type end-use model; Denryoku chuo kenkyusho Nihon Sogo Kenkyusho kyodo kenkyu hokokusho. Nippon gata end use model no gainen kochiku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    The concept of Japanese type demand analysis model (end-use model) was constructed for the efficient management of electric power companies and efficient power utilization. Diffusion and use conditions of domestic air conditioners are considerably different depending on local life style and climate. In order to design demand measures considering combination of appliances in every market segment, demands in an end use level (end demand level, each appliance level) should be acquired. The basic structure of the model is composed of various exogenous variables such as weather data, price and ups and downs trend of customers, and various appliance data such as size, efficiency and energy consumption rate, and various customer data such as possession rate of appliances and number of customers. The final energy demand is estimated by integrating the above variables. By systematizing the stored data of precise actual load conditions, construction of DSM (demand side management) strategy becomes possible by using computer tools. 8 refs., 15 figs., 13 tabs.

  5. Crosstalk in an FDM Laboratory Setup and the Athena X-IFU End-to-End Simulator

    Science.gov (United States)

    den Hartog, R.; Kirsch, C.; de Vries, C.; Akamatsu, H.; Dauser, T.; Peille, P.; Cucchetti, E.; Jackson, B.; Bandler, S.; Smith, S.; Wilms, J.

    2018-04-01

    The impact of various crosstalk mechanisms on the performance of the Athena X-IFU instrument has been assessed with detailed end-to-end simulations. For the crosstalk in the electrical circuit, a detailed model has been developed. In this contribution, we test this model against measurements made with an FDM laboratory setup and discuss the assumption of deterministic crosstalk in the context of the weak link effect in the detectors. We conclude that crosstalk levels predicted by the model are conservative with respect to the observed levels.

  6. End-to-end integrated security and performance analysis on the DEGAS Choreographer platform

    DEFF Research Database (Denmark)

    Buchholtz, Mikael; Gilmore, Stephen; Haenel, Valentin

    2005-01-01

    We present a software tool platform which facilitates security and performance analysis of systems which starts and ends with UML model descriptions. A UML project is presented to the platform for analysis, formal content is extracted in the form of process calculi descriptions, analysed with the......We present a software tool platform which facilitates security and performance analysis of systems which starts and ends with UML model descriptions. A UML project is presented to the platform for analysis, formal content is extracted in the form of process calculi descriptions, analysed...

  7. A wide-range model of two-group gross sections in the dynamics code HEXTRAN

    International Nuclear Information System (INIS)

    Kaloinen, E.; Peltonen, J.

    2002-01-01

    In dynamic analyses the thermal hydraulic conditions within the reactor core may have a large variation, which sets a special requirement on the modeling of cross sections. The standard model in the dynamics code HEXTRAN is the same as in the static design code HEXBU-3D/MODS. It is based on a linear and second order fitting of two-group cross sections on fuel and moderator temperature, moderator density and boron density. A new, wide-range model of cross sections developed in Fortum Nuclear Services for HEXBU-3D/MOD6 has been included as an option into HEXTRAN. In this model the nodal cross sections are constructed from seven state variables in a polynomial of more than 40 terms. Coefficients of the polynomial are created by a least squares fitting to the results of a large number of fuel assembly calculations. Depending on the choice of state variables for the spectrum calculations, the new cross section model is capable to cover local conditions from cold zero power to boiling at full power. The 5. dynamic benchmark problem of AER is analyzed with the new option and results are compared to calculations with the standard model of cross sections in HEXTRAN (Authors)

  8. Dynamics of Longitudinal Impact in the Variable Cross-Section Rods

    Science.gov (United States)

    Stepanov, R.; Romenskyi, D.; Tsarenko, S.

    2018-03-01

    Dynamics of longitudinal impact in rods of variable cross-section is considered. Rods of various configurations are used as elements of power pulse systems. There is no single method to the construction of a mathematical model of longitudinal impact on rods. The creation of a general method for constructing a mathematical model of longitudinal impact for rods of variable cross-section is the goal of the article. An elastic rod is considered with a cross-sectional area varying in powers of law from the longitudinal coordinate. The solution of the wave equation is obtained using the Fourier method. Special functions are introduced on the basis of recurrence relations for Bessel functions for solving boundary value problems. The expression for the square of the norm is obtained taking into account the orthogonality property of the eigen functions with weight. For example, the impact of an inelastic mass along the wide end of a conical rod is considered. The expressions for the displacements, forces and stresses of the rod sections are obtained for the cases of sudden velocity communication and the application of force. The proposed mathematical model makes it possible to carry out investigations of the stress-strain state in rods of variable and constant cross-section for various conditions of dynamic effects.

  9. 49 CFR 231.9 - Tank cars without end sills.

    Science.gov (United States)

    2010-10-01

    ... clearance, within 30 inches of side of car, until car is shopped for work amounting to practically... 49 Transportation 4 2010-10-01 2010-10-01 false Tank cars without end sills. 231.9 Section 231.9..., DEPARTMENT OF TRANSPORTATION RAILROAD SAFETY APPLIANCE STANDARDS § 231.9 Tank cars without end sills. (a...

  10. Improvement of Axial Reflector Cross Section Generation Model for PWR Core Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Shim, Cheon Bo; Lee, Kyung Hoon; Cho, Jin Young [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    This paper covers the study for improvement of axial reflector XS generation model. In the next section, the improved 1D core model is represented in detail. Reflector XS generated by the improved model is compared to that of the conventional model in the third section. Nuclear design parameters generated by these two XS sets are also covered in that section. Significant of this study is discussed in the last section. Two-step procedure has been regarded as the most practical approach for reactor core designs because it offers core design parameters quite rapidly within acceptable range. Thus this approach is adopted for SMART (System-integrated Modular Advanced Reac- Tor) core design in KAERI with the DeCART2D1.1/ MASTER4.0 (hereafter noted as DeCART2D/ MASTER) code system. Within the framework of the two-step procedure based SMART core design, various researches have been studied to improve the core design reliability and efficiency. One of them is improvement of reflector cross section (XS) generation models. While the conventional FA/reflector two-node model used for most core designs to generate reflector XS cannot consider the actual configuration of fuel rods that intersect at right angles to axial reflectors, the revised model reflects the axial fuel configuration by introducing the radially simplified core model. The significance of the model revision is evaluated by observing HGC generated by DeCART2D, reflector XS, and core design parameters generated by adopting the two models. And it is verified that about 30 ppm CBC error can be reduced and maximum Fq error decreases from about 6 % to 2.5 % by applying the revised model. Error of AO and axial power shapes are also reduced significantly. Therefore it can be concluded that the simplified 1D core model improves the accuracy of the axial reflector XS and leads to the two-step procedure reliability enhancement. Since it is hard for core designs to be free from the two-step approach, it is necessary to find

  11. Parallel phase model : a programming model for high-end parallel machines with manycores.

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Junfeng (Syracuse University, Syracuse, NY); Wen, Zhaofang; Heroux, Michael Allen; Brightwell, Ronald Brian

    2009-04-01

    This paper presents a parallel programming model, Parallel Phase Model (PPM), for next-generation high-end parallel machines based on a distributed memory architecture consisting of a networked cluster of nodes with a large number of cores on each node. PPM has a unified high-level programming abstraction that facilitates the design and implementation of parallel algorithms to exploit both the parallelism of the many cores and the parallelism at the cluster level. The programming abstraction will be suitable for expressing both fine-grained and coarse-grained parallelism. It includes a few high-level parallel programming language constructs that can be added as an extension to an existing (sequential or parallel) programming language such as C; and the implementation of PPM also includes a light-weight runtime library that runs on top of an existing network communication software layer (e.g. MPI). Design philosophy of PPM and details of the programming abstraction are also presented. Several unstructured applications that inherently require high-volume random fine-grained data accesses have been implemented in PPM with very promising results.

  12. Centrifuge modeling of rapid load tests with open-ended piles

    NARCIS (Netherlands)

    Nguyen, T.C.; Van Lottum, H.; Holscher, P.; Van Tol, A.F.

    2012-01-01

    Rapid and static load tests were conducted on open-ended and close-ended piles in the Deltares GeoCentriflige. hi flight, a pile was driven into the soil. Both fme-grained sand and silt beds were tested. Both the rapid and static soil resistances o f a close-ended pile were higher than the soil

  13. Neutrino-carbon cross section in QRPA models

    International Nuclear Information System (INIS)

    Samana, Arturo R.; Krmpotic, Francisco; Bertulani, Carlos A.; Paar, Nils

    2009-01-01

    Full text follows. The ν/ν-bar - 12 C cross sections are calculated in the projected quasiparticle random phase approximation (PQRPA) [1,2] and the relativistic quasiparticle random phase approximation (RQRPA) [3,4]. We compare these cross section as a function of the incident neutrino energy and the number of shells used in the nuclear structure calculation. Additional comparison with other RPA models are performed. A guide to find an upper limit of the incident neutrino energy as a function of the number of shell is implemented. Important consequences on the extrapolation of the cross section to higher neutrino energies is discussed. The formalism obtained in Ref. [1] for the neutrino interaction is extended for antineutrino scattering. This formalism includes the effect of the violation of the Conserved Vector Current by the Coulomb field. It is furthermore simplified by classifying the nuclear matrix elements in natural and unnatural parities. The distribution of cross sections averaged with the Michel spectrum as well as with other estimated fluxes for future experiments are compared for ν e and ν-bar e . Some astrophysical implications are addressed. References [1] F. Krmpotic, A. Mariano and A. Samana, Phys.Lett. B541, 298 (2002). [2] F. Krmpotic, A. Mariano and A. Samana, Phys. Rev. C 71, 044319 (2005). [3] N. Paar, T. Niksic, D. Vretenar, and P. Ring, Phys. Rev. C 69, 054303 (2004). [4] N. Paar, D. Vretenar, T. Marketin and P. Ring, Phys. Rev. C 77, 024608 (2008)

  14. Development of a global aerosol model using a two-dimensional sectional method: 1. Model design

    Science.gov (United States)

    Matsui, H.

    2017-08-01

    This study develops an aerosol module, the Aerosol Two-dimensional bin module for foRmation and Aging Simulation version 2 (ATRAS2), and implements the module into a global climate model, Community Atmosphere Model. The ATRAS2 module uses a two-dimensional (2-D) sectional representation with 12 size bins for particles from 1 nm to 10 μm in dry diameter and 8 black carbon (BC) mixing state bins. The module can explicitly calculate the enhancement of absorption and cloud condensation nuclei activity of BC-containing particles by aging processes. The ATRAS2 module is an extension of a 2-D sectional aerosol module ATRAS used in our previous studies within a framework of a regional three-dimensional model. Compared with ATRAS, the computational cost of the aerosol module is reduced by more than a factor of 10 by simplifying the treatment of aerosol processes and 2-D sectional representation, while maintaining good accuracy of aerosol parameters in the simulations. Aerosol processes are simplified for condensation of sulfate, ammonium, and nitrate, organic aerosol formation, coagulation, and new particle formation processes, and box model simulations show that these simplifications do not substantially change the predicted aerosol number and mass concentrations and their mixing states. The 2-D sectional representation is simplified (the number of advected species is reduced) primarily by the treatment of chemical compositions using two interactive bin representations. The simplifications do not change the accuracy of global aerosol simulations. In part 2, comparisons with measurements and the results focused on aerosol processes such as BC aging processes are shown.

  15. An Equivalent cross-section Framework for improving computational efficiency in Distributed Hydrologic Modelling

    Science.gov (United States)

    Khan, Urooj; Tuteja, Narendra; Ajami, Hoori; Sharma, Ashish

    2014-05-01

    While the potential uses and benefits of distributed catchment simulation models is undeniable, their practical usage is often hindered by the computational resources they demand. To reduce the computational time/effort in distributed hydrological modelling, a new approach of modelling over an equivalent cross-section is investigated where topographical and physiographic properties of first-order sub-basins are aggregated to constitute modelling elements. To formulate an equivalent cross-section, a homogenization test is conducted to assess the loss in accuracy when averaging topographic and physiographic variables, i.e. length, slope, soil depth and soil type. The homogenization test indicates that the accuracy lost in weighting the soil type is greatest, therefore it needs to be weighted in a systematic manner to formulate equivalent cross-sections. If the soil type remains the same within the sub-basin, a single equivalent cross-section is formulated for the entire sub-basin. If the soil type follows a specific pattern, i.e. different soil types near the centre of the river, middle of hillslope and ridge line, three equivalent cross-sections (left bank, right bank and head water) are required. If the soil types are complex and do not follow any specific pattern, multiple equivalent cross-sections are required based on the number of soil types. The equivalent cross-sections are formulated for a series of first order sub-basins by implementing different weighting methods of topographic and physiographic variables of landforms within the entire or part of a hillslope. The formulated equivalent cross-sections are then simulated using a 2-dimensional, Richards' equation based distributed hydrological model. The simulated fluxes are multiplied by the weighted area of each equivalent cross-section to calculate the total fluxes from the sub-basins. The simulated fluxes include horizontal flow, transpiration, soil evaporation, deep drainage and soil moisture. To assess

  16. Random walkers with extreme value memory: modelling the peak-end rule

    Science.gov (United States)

    Harris, Rosemary J.

    2015-05-01

    Motivated by the psychological literature on the ‘peak-end rule’ for remembered experience, we perform an analysis within a random walk framework of a discrete choice model where agents’ future choices depend on the peak memory of their past experiences. In particular, we use this approach to investigate whether increased noise/disruption always leads to more switching between decisions. Here extreme value theory illuminates different classes of dynamics indicating that the long-time behaviour is dependent on the scale used for reflection; this could have implications, for example, in questionnaire design.

  17. Modelling and performance of heat pipes with long evaporator sections

    Science.gov (United States)

    Wits, Wessel W.; te Riele, Gert Jan

    2017-11-01

    This paper presents a planar cooling strategy for advanced electronic applications using heat pipe technology. The principle idea is to use an array of relatively long heat pipes, whereby heat is disposed to a long section of the pipes. The proposed design uses 1 m long heat pipes and top cooling through a fan-based heat sink. Successful heat pipe operation and experimental performances are determined for seven heating configurations, considering active bottom, middle and top sections, and four orientation angles (0°, 30°, 60° and 90°). For all heating sections active, the heat pipe oriented vertically in an evaporator-down mode and a power input of 150 W, the overall thermal resistance was 0.014 K/W at a thermal gradient of 2.1 K and an average operating temperature of 50.7 °C. Vertical operation showed best results, as can be expected; horizontally the heat pipe could not be tested up to the power limit and dry-out occurred between 20 and 80 W depending on the heating configuration. Heating configurations without the bottom section active demonstrated a dynamic start-up effect, caused by heat conduction towards the liquid pool and thereafter batch-wise introducing the working fluid into the two-phase cycle. By analysing the heat pipe limitations for the intended operating conditions, a suitable heat pipe geometry was chosen. To predict the thermal performance a thermal model using a resistance network was created. The model compares well with the measurement data, especially for higher input powers. Finally, the thermal model is used for the design of a 1 kW planar system-level electronics cooling infrastructure featuring six 1 m heat pipes in parallel having a long ( 75%) evaporator section.

  18. Means-end theory of lifestyle

    DEFF Research Database (Denmark)

    Scholderer, Joachim; Brunsø, Karen; Grunert, Klaus G.

    2002-01-01

    Brunsø, Scholderer and Grunert (in press) reconstruct means-end chain theory and lifestyle within a dual-process framework, incorporating bottom-up and top-down information-processing routes. The bottom-up route of their model is defined as a hierarchical categorization process, and the top...... of the intervening knowledge structures is considered a necessary condition for both information-processing routes to reach their ends, predicting a complete-mediation model. The initial study by Brunsø et al. (in press) was exactly replicated based on survey data gathered in the United Kingdom in 1998, using...... modeling. Compared against five alternative model structures, the complete-mediation model fitted the data best, thus confirming the predictions derived from the reconstructed theory, and cross-validating the initial model in a different consumer population....

  19. Large Signal Circuit Model of Two-Section Gain Lever Quantum Dot Laser

    International Nuclear Information System (INIS)

    Horri Ashkan; Mirmoeini Seyedeh Zahra; Faez Rahim

    2012-01-01

    An equivalent circuit model for the design and analysis of two-section gain lever quantum dot (QD) laser is presented. This model is based on the three level rate equations with two independent carrier populations and a single longitudinal optical mode. By using the presented model, the effect of gain lever on QD laser performances is investigated. The results of simulation show that the main characteristics of laser such as threshold current, transient response, output power and modulation response are affected by differential gain ratios between the two-sections

  20. Charged-current inclusive neutrino cross sections in the SuperScaling model

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, M. V., E-mail: martin.inrne@gmail.com [Institute for Nuclear Research and Nuclear Energy, Bulgarian Academy of Sciences, Sofia 1784 (Bulgaria); Grupo de Física Nuclear, Departamento de Física Atómica, Molecular y Nuclear, Facultad de Ciencias Físicas, Universidad Complutense de Madrid, Madrid E-28040 (Spain); Megias, G. D.; Caballero, J. A. [Departamento de Física Atómica, Molecular y Nuclear, Universidad de Sevilla, 41080 Sevilla (Spain); González-Jiménez, R. [Department of Physics and Astronomy, Ghent University, Proeftuinstraat 86, B-9000 Gent (Belgium); Moreno, O.; Donnelly, T. W. [Center for Theoretical Physics, Laboratory for Nuclear Science and Department of Physics, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Barbaro, M. B. [Dipartimento di Fisica, Università di Torino and INFN, Sezione di Torino, Via P. Giuria 1, 10125 Torino (Italy); Antonov, A. N. [Institute for Nuclear Research and Nuclear Energy, Bulgarian Academy of Sciences, Sofia 1784 (Bulgaria); Moya de Guerra, E.; Udías, J. M. [Grupo de Física Nuclear, Departamento de Física Atómica, Molecular y Nuclear, Facultad de Ciencias Físicas, Universidad Complutense de Madrid, Madrid E-28040 (Spain)

    2016-03-25

    SuperScaling model (SuSA) predictions to neutrino-induced charged-current π{sup +} production in the Δ-resonance region are explored under MiniBooNE experimental conditions. The SuSA charged-current π{sup +} results are in good agreement with data on neutrino flux-averaged double-differential cross sections. The SuSA model for quasielastic scattering and its extension to the pion production region are used for predictions of charged-current inclusive neutrino-nucleus cross sections. Results are also compared with the T2K experimental data for inclusive scattering.

  1. 40 CFR 63.487 - Batch front-end process vents-reference control technology.

    Science.gov (United States)

    2010-07-01

    ... § 63.487 Batch front-end process vents—reference control technology. (a) Batch front-end process vents... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Batch front-end process vents-reference control technology. 63.487 Section 63.487 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...

  2. Comparing the dependability and associations with functioning of the DSM-5 Section III trait model of personality pathology and the DSM-5 Section II personality disorder model.

    Science.gov (United States)

    Chmielewski, Michael; Ruggero, Camilo J; Kotov, Roman; Liu, Keke; Krueger, Robert F

    2017-07-01

    Two competing models of personality psychopathology are included in the fifth edition of the Diagnostic Statistical Manual of Mental Disorders ( DSM-5 ; American Psychiatric Association, 2013); the traditional personality disorder (PD) model included in Section II and an alternative trait-based model included in Section III. Numerous studies have examined the validity of the alternative trait model and its official assessment instrument, the Personality Inventory for DSM-5 (PID-5; Krueger, Derringer, Markon, Watson, & Skodol, 2012). However, few studies have directly compared the trait-based model to the traditional PD model empirically in the same dataset. Moreover, to our knowledge, only a single study (Suzuki, Griffin, & Samuel, 2015) has examined the dependability of the PID-5, which is an essential component of construct validity for traits (Chmielewski & Watson, 2009; McCrae, Kurtz, Yamagata, & Terracciano, 2011). The current study directly compared the dependability of the DSM-5 traits, as assessed by the PID-5, and the traditional PD model, as assessed by the Personality Diagnostic Questionnaire-4 (PDQ-4+), in a large undergraduate sample. In addition, it evaluated and compared their associations with functioning, another essential component of personality pathology. In general, our findings indicate that most DSM-5 traits demonstrate high levels of dependability that are superior to the traditional PD model; however, some of the constructs assessed by the PID-5 may be more state like. The models were roughly equivalent in terms of their associations with functioning. The current results provide additional support for the validity of PID-5 and the DSM-5 Section III personality pathology model. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  3. Empirical models for end-use properties prediction of LDPE: application in the flexible plastic packaging industry

    Directory of Open Access Journals (Sweden)

    Maria Carolina Burgos Costa

    2008-03-01

    Full Text Available The objective of this work is to develop empirical models to predict end use properties of low density polyethylene (LDPE resins as functions of two intrinsic properties easily measured in the polymers industry. The most important properties for application in the flexible plastic packaging industry were evaluated experimentally for seven commercial polymer grades. Statistical correlation analysis was performed for all variables and used as the basis for proper choice of inputs to each model output. Intrinsic properties selected for resin characterization are fluidity index (FI, which is essentially an indirect measurement of viscosity and weight average molecular weight (MW, and density. In general, models developed are able to reproduce and predict experimental data within experimental accuracy and show that a significant number of end use properties improve as the MW and density increase. Optical properties are mainly determined by the polymer morphology.

  4. Photoproduction within the two-component Dual Parton Model: amplitudes and cross sections

    International Nuclear Information System (INIS)

    Engel, R.; Siegen Univ.

    1995-01-01

    In the framework of the Dual Parton Model an approximation scheme to describe high energy photoproduction processes is presented. Based on the distinction between direct, resolved soft, and resolved hard interaction processes we construct effective impact parameter amplitudes. In order to treat low mass diffraction within the eikonal formalism in a consistent way a phenomenological ansatz is proposed. The free parameters of the model are determined by fits to high energy hadro- and photoproduction cross sections. We calculate the partial photoproduction cross sections and discuss predictions of the model at HERA energies. Using hadro- and photoproduction data together, the uncertainties of the model predictions are strongly reduced. (orig.)

  5. HINS Linac front end focusing system R and D

    International Nuclear Information System (INIS)

    Apollinari, G.; Carcagno, R.H.; Dimarco, J.; Huang, Y.; Kashikhin, V.V.; Orris, D.F.; Page, T.M.; Rabehl, R.; Sylvester, C.; Tartaglia, M.A.; Terechkine, I.; Fermilab; Argonne

    2008-01-01

    This report summarizes current status of an R and D program to develop a focusing system for the front end of a superconducting RF linac. Superconducting solenoids will be used as focusing lenses in the low energy accelerating sections of the front end. The development of focusing lenses for the first accelerating section is in the production stage, and lens certification activities are in preparation at FNAL. The report contains information about the focusing lens design and performance, including solenoid, dipole corrector, and power leads, and about cryogenic system design and performance. It also describes the lens magnetic axis position measurement technique and discusses scope of an acceptance/certification process

  6. Perturbation analysis for Monte Carlo continuous cross section models

    International Nuclear Information System (INIS)

    Kennedy, Chris B.; Abdel-Khalik, Hany S.

    2011-01-01

    Sensitivity analysis, including both its forward and adjoint applications, collectively referred to hereinafter as Perturbation Analysis (PA), is an essential tool to complete Uncertainty Quantification (UQ) and Data Assimilation (DA). PA-assisted UQ and DA have traditionally been carried out for reactor analysis problems using deterministic as opposed to stochastic models for radiation transport. This is because PA requires many model executions to quantify how variations in input data, primarily cross sections, affect variations in model's responses, e.g. detectors readings, flux distribution, multiplication factor, etc. Although stochastic models are often sought for their higher accuracy, their repeated execution is at best computationally expensive and in reality intractable for typical reactor analysis problems involving many input data and output responses. Deterministic methods however achieve computational efficiency needed to carry out the PA analysis by reducing problem dimensionality via various spatial and energy homogenization assumptions. This however introduces modeling error components into the PA results which propagate to the following UQ and DA analyses. The introduced errors are problem specific and therefore are expected to limit the applicability of UQ and DA analyses to reactor systems that satisfy the introduced assumptions. This manuscript introduces a new method to complete PA employing a continuous cross section stochastic model and performed in a computationally efficient manner. If successful, the modeling error components introduced by deterministic methods could be eliminated, thereby allowing for wider applicability of DA and UQ results. Two MCNP models demonstrate the application of the new method - a Critical Pu Sphere (Jezebel), a Pu Fast Metal Array (Russian BR-1). The PA is completed for reaction rate densities, reaction rate ratios, and the multiplication factor. (author)

  7. End-of-life conversations and care: an asset-based model for community engagement.

    Science.gov (United States)

    Matthiesen, Mary; Froggatt, Katherine; Owen, Elaine; Ashton, John R

    2014-09-01

    Public awareness work regarding palliative and end-of-life care is increasingly promoted within national strategies for palliative care. Different approaches to undertaking this work are being used, often based upon broader educational principles, but little is known about how to undertake such initiatives in a way that equally engages both the health and social care sector and the local communities. An asset-based community engagement approach has been developed that facilitates community-led awareness initiatives concerning end-of-life conversations and care by identifying and connecting existing skills and expertise. (1) To describe the processes and features of an asset-based community engagement approach that facilitates community-led awareness initiatives with a focus on end-of-life conversations and care; and (2) to identify key community-identified priorities for sustainable community engagement processes. An asset-based model of community engagement specific to end-of-life issues using a four-step process is described (getting started, coming together, action planning and implementation). The use of this approach, in two regional community engagement programmes, based across rural and urban communities in the northwest of England, is described. The assets identified in the facilitated community engagement process encompassed people's talents and skills, community groups and networks, government and non-government agencies, physical and economic assets and community values and stories. Five priority areas were addressed to ensure active community engagement work: information, outreach, education, leadership and sustainability. A facilitated, asset-based approach of community engagement for end-of-life conversations and care can catalyse community-led awareness initiatives. This occurs through the involvement of community and local health and social care organisations as co-creators of this change across multiple sectors in a sustainable way. This approach

  8. Model of a generator end-winding cage; Modelisation d`une cage de developpantes d`alternateur

    Energy Technology Data Exchange (ETDEWEB)

    Leger, A.C.; Fanton, J.P.; Davies, C.

    1994-09-01

    This document presents some studies concerning the vibratory characterization of particular structures called: generator end-winding cages. These structures are mainly made up of the endings of armature windings. The question of their good mechanical behaviour is of prime importance, since they are submitted to high electromagnetic efforts during the different electrical ratings encountered during operation. The designer (GEC-Alsthom) and the user (EDF) have both undertaken numerical calculations in order to characterize a given machine, in this case a 600 MW bipolar generator; it appeared interesting to compare such calculations. The models realized respectively by GEC-Alsthom and EDF make use of different techniques and hypotheses. GEC-Alsthom represents the sets of rods and spacers by plates, which properties are determined by a pre-processor. The model is simplified to take into account the existing symmetries. It takes profit of previous experience and aims at a fast utilisation. The EDF model tends to allow a further comprehensive calculation, form the electromagnetic efforts to the determination of local stresses. The whole set of the constituting elements of the structure is modelled by beams, which leads to an important size for the model (21 000 degrees of freedom). The validation performed on the two models has been focused on the comparison between respective results and also with experimental results. Each model provides values for the first eigenfrequencies and the associated modes shapes. (authors). 3 refs., 3 figs., 2 tabs.

  9. Mudaraba-Venture Capital Closed-end Mutual Funds and Mudaraba-Venture Capital Open-end Mutual Funds

    OpenAIRE

    Halil Ibrahim Bulut

    2008-01-01

    The important part of this study attempts to explain that both venture capital and interest-free financing are based on similar ground, if not the same. Two new models called Mudaraba-Venture Capital Closed-End Mutual Funds and Mudaraba-Venture Capital Open-End Mutual Funds, based on both the similarities and the needs of financial innovation in the interest-free financing system, are detailed. It is believed that the development of these two models could make some improvements not only in th...

  10. End-of-life care in the United States: policy issues and model programs of integrated care

    Directory of Open Access Journals (Sweden)

    Joshua M. Wiener

    2003-05-01

    Full Text Available Background: End-of-life care financing and delivery in the United States is fragmented and uncoordinated, with little integration of acute and long-term care services. Objective: To assess policy issues involving end-of-life care, especially involving the hospice benefit, and to analyse model programs of integrated care for people who are dying. Methods: The study conducted structured interviews with stakeholders and experts in end-of-life care and with administrators of model programs in the United States, which were nominated by the experts. Results: The two major public insurance programs—Medicare and Medicaid—finance the vast majority of end-of-life care. Both programs offer a hospice benefit, which has several shortcomings, including requiring physicians to make a prognosis of a six month life expectancy and insisting that patients give up curative treatment—two steps which are difficult for doctors and patients to make—and payment levels that may be too low. In addition, quality of care initiatives for nursing homes and hospice sometimes conflict. Four innovative health systems have overcome these barriers to provide palliative services to beneficiaries in their last year of life. Three of these health systems are managed care plans which receive capitated payments. These providers integrate health, long-term and palliative care using an interdisciplinary team approach to management of services. The fourth provider is a hospice that provides palliative services to beneficiaries of all ages, including those who have not elected hospice care. Conclusions: End-of-life care is deficient in the United States. Public payers could use their market power to improve care through a number of strategies.

  11. End-Users, Front Ends and Librarians.

    Science.gov (United States)

    Bourne, Donna E.

    1989-01-01

    The increase in end-user searching, the advantages and limitations of front ends, and the role of the librarian in end-user searching are discussed. It is argued that librarians need to recognize that front ends can be of benefit to themselves and patrons, and to assume the role of advisors and educators for end-users. (37 references) (CLB)

  12. End design of the SSC 58 mm High Gradient Quadrupole

    International Nuclear Information System (INIS)

    Caspi, S.

    1992-01-01

    The ''end'' design of the High Gradient Quad. was done with consideration to the integrated field harmonics, the iron contribution, and the maximum field at the conductor. Magnetic analysis was done on the return end only, however the physical dimension of the lead end were determined as well. Using the cross-section of the windings and Cook's program BEND, we generated the physical end windings around the return end. Placing a single wire at the center of each turn the integrated gradient was computed and iterating on the end block spacers the integrated harmonics minimized. The final geometry was then used for more, extensive calculations, such as the field at the conductor and the 3D field harmonics. For this detailed calculation we have placed a single line current at the center of each strand and included the iron contribution (μ = ∞), see Appendix C. With the termination of the iron serving as a reference, the maximum length of the inner and outer layers are 182 mm and 215 mm respectively. The magnetic length of the end was computed from the gradient function A 2 and was found to be 142 mm. In reality we expect the physical length of the end to be somewhat larger, however this should have little or no effect on the magnetic length. The gradient in the straight section is 212.44 T/m at 7000 A and the integrated value of the gradient is -3.01665 E5 (G) in the end region marked by the magnetic length of the end. The respective integrated harmonics for the end 12 pole and 20 pole are -10.6658 (G/CM 4 ) and 0.7279 (G/cm 8 ) corresponding to b 6 = 0.351 , b 10 = -0.024 units. The above was computed from the values of A 2 , A 6 , and A 10

  13. Refinement of a Conceptual Model for Adolescent Readiness to Engage in End-of-Life Discussions.

    Science.gov (United States)

    Bell, Cynthia J; Zimet, Gregory D; Hinds, Pamela S; Broome, Marion E; McDaniel, Anna M; Mays, Rose M; Champion, Victoria L

    Adolescents living with incurable cancer require ongoing support to process grief, emotions, and information as disease progresses including treatment options (phase 1 clinical trials and/or hospice/palliative care). Little is known about how adolescents become ready for such discussions. The purpose of this study was to explore the process of adolescent readiness for end-of-life preparedness discussions, generating a theoretical understanding for guiding clinical conversations when curative options are limited. We explored 2 in-depth cases across time using case-study methodology. An à priori conceptual model based on current end-of-life research guided data collection and analysis. Multiple sources including in-depth adolescent interviews generated data collection on model constructs. Analysis followed a logical sequence establishing a chain of evidence linking raw data to study conclusions. Synthesis and data triangulation across cases and time led to theoretical generalizations. Initially, we proposed a linear process of readiness with 3 domains: a cognitive domain (awareness), an emotional domain (acceptance), and a behavioral domain (willingness), which preceded preparedness. Findings led to conceptual model refinement showing readiness is a dynamic internal process that interacts with preparedness. Current awareness context facilitates the type of preparedness discussions (cognitive or emotional). Furthermore, social constraint inhibits discussions. Data support theoretical understanding of the dynamism of readiness. Future research that validates adolescent conceptualization will ensure age-appropriate readiness representation. Understanding the dynamic process of readiness for engaging in end-of-life preparedness provides clinician insight for guiding discussions that facilitate shared decision making and promote quality of life for adolescents and their families.

  14. Mean multiplicity in the Regge models with rising cross sections

    International Nuclear Information System (INIS)

    Chikovani, Z.E.; Kobylisky, N.A.; Martynov, E.S.

    1979-01-01

    Behaviour of the mean multiplicity and the total cross section σsub(t) of hadron-hadron interactions is considered in the framework of the Regge models at high energies. Generating function was plotted for models of dipole and froissaron, and the mean multiplicity and multiplicity moments were calculated. It is shown that approximately ln 2 S (energy square) in the dipole model, which is in good agreement with the experiment. It is also found that in various Regge models approximately σsub(t)lnS

  15. Construction of tomographic head model using sectioned photographic images of cadaver

    International Nuclear Information System (INIS)

    Lee, Choon Sik; Lee, Jai Ki; Park, Jin Seo; Chung, Min Suk

    2004-01-01

    Tomographic models are currently the most complete, developed and realistic models of the human anatomy. They have been used to estimate organ doses for diagnostic radiation examination and radiotherapy treatment planning, and radiation protection. The quality of original anatomic images is a key factor to build a quality tomographic model. Computed tomography (CT) and magnetic resonance imaging (MRI) scan, from which most of current tomographic models are constructed, have their inherent shortcomings. In this study, a tomographic model of Korean adult male head was constructed by using serially sectioned photographs of cadaver. The cadaver was embedded, frozen, serially sectioned and photographed by high resolution digital camera at 0.2 mm interval. The contours of organs and tissues in photographs were segmented by several trained anatomists. The 120 segmented images of head at 2mm interval were converted into binary files and ported into Monte Carlo code to perform an example calculation of organ dose. Whole body tomographic model will be constructed by using the procedure developed in this study

  16. Absolute cross sections from the ''boomerang model'' for resonant electron-molecule scattering

    International Nuclear Information System (INIS)

    Dube, L.; Herzenberg, A.

    1979-01-01

    The boomerang model is used to calculate absolute cross sections near the 2 Pi/sub g/ shape resonance in e-N 2 scattering. The calculated cross sections are shown to satisfy detailed balancing. The exchange of electrons is taken into account. A parametrized complex-potential curve for the intermediate N 2 /sup ts-/ ion is determined from a small part of the experimental data, and then used to calculate other properties. The calculations are in good agreement with the absolute cross sections for vibrational excitation from the ground state, the absolute cross section v = 1 → 2, and the absolute total cross section

  17. Modeling and Simulation of Satellite Subsystems for End-to-End Spacecraft Modeling

    National Research Council Canada - National Science Library

    Schum, William K; Doolittle, Christina M; Boyarko, George A

    2006-01-01

    During the past ten years, the Air Force Research Laboratory (AFRL) has been simultaneously developing high-fidelity spacecraft payload models as well as a robust distributed simulation environment for modeling spacecraft subsystems...

  18. Incomplete information and the closed-end fund discount

    OpenAIRE

    Barone-Adesi, Giovanni; Kim, Youngsoo

    2008-01-01

    We model the closed-end fund discount/premium in a version of Merton’s (1978) asset pricing model with incomplete information. In this economy, investors trade only assets which they “ know about” . The model generates a closed-end fund discount or premium, depending on risk-aversion parameters. The fund share price reverts to the net asset value on open-ending of the fund. The discount/premium is a result of two economic forces: (1) the fund manager’s objective is to maximize expected utilit...

  19. Robotic end-effector for rewaterproofing shuttle tiles

    Science.gov (United States)

    Manouchehri, Davoud; Hansen, Joseph M.; Wu, Cheng M.; Yamamoto, Brian S.; Graham, Todd

    1992-11-01

    This paper summarizes work by Rockwell International's Space Systems Division's Robotics Group at Downey, California. The work is part of a NASA-led team effort to automate Space Shuttle rewaterproofing in the Orbiter Processing Facility at the Kennedy Space Center and the ferry facility at the Ames-Dryden Flight Research Facility. Rockwell's effort focuses on the rewaterproofing end-effector, whose function is to inject hazardous dimethylethyloxysilane into thousands of ceramic tiles on the underside of the orbiter after each flight. The paper has five sections. First, it presents background on the present manual process. Second, end-effector requirements are presented, including safety and interface control. Third, a design is presented for the five end-effector systems: positioning, delivery, containment, data management, and command and control. Fourth, end-effector testing and integrating to the total system are described. Lastly, future applications for this technology are discussed.

  20. 20 CFR 408.816 - When does SVB entitlement end due to death?

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false When does SVB entitlement end due to death? 408.816 Section 408.816 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SPECIAL BENEFITS FOR CERTAIN WORLD WAR II VETERANS Suspensions and Terminations Termination § 408.816 When does SVB entitlement end due to death? Your SVB entitlement ends wit...

  1. Sediment transport processes in the Pearl River Estuary as revealed by grain-size end-member modeling and sediment trend analysis

    Science.gov (United States)

    Li, Tao; Li, Tuan-Jie

    2018-04-01

    The analysis of grain-size distribution enables us to decipher sediment transport processes and understand the causal relations between dynamic processes and grain-size distributions. In the present study, grain sizes were measured from surface sediments collected in the Pearl River Estuary and its adjacent coastal areas. End-member modeling analysis attempts to unmix the grain sizes into geologically meaningful populations. Six grain-size end-members were identified. Their dominant modes are 0 Φ, 1.5 Φ, 2.75 Φ, 4.5 Φ, 7 Φ, and 8 Φ, corresponding to coarse sand, medium sand, fine sand, very coarse silt, silt, and clay, respectively. The spatial distributions of the six end-members are influenced by sediment transport and depositional processes. The two coarsest end-members (coarse sand and medium sand) may reflect relict sediments deposited during the last glacial period. The fine sand end-member would be difficult to transport under fair weather conditions, and likely indicates storm deposits. The three remaining fine-grained end-members (very coarse silt, silt, and clay) are recognized as suspended particles transported by saltwater intrusion via the flood tidal current, the Guangdong Coastal Current, and riverine outflow. The grain-size trend analysis shows distinct transport patterns for the three fine-grained end-members. The landward transport of the very coarse silt end-member occurs in the eastern part of the estuary, the seaward transport of the silt end-member occurs in the western part, and the east-west transport of the clay end-member occurs in the coastal areas. The results show that grain-size end-member modeling analysis in combination with sediment trend analysis help to better understand sediment transport patterns and the associated transport mechanisms.

  2. MARS-LMR modeling for the post-test analysis of Phenix End-of-Life natural circulation

    International Nuclear Information System (INIS)

    Jeong, Hae Yong; Ha, Kwi Seok; Chang, Won Pyo; Lee, Kwi Lim

    2011-01-01

    For a successful design and analysis of Sodium cooled Fast Reactor (SFR), it is required to have a reliable and well-proven system analysis code. To achieve this purpose, KAERI is enhancing the modeling capability of MARS code by adding the SFR-specific models such as pressure drop model, heat transfer model and reactivity feedback model. This version of MARS-LMR will be used as a basic tool in the design and analysis of future SFR systems in Korea. Before wide application of MARS-LMR code, it is required to verify and validate the code models through analyses for appropriate experimental data or analytical results. The end-of-life test of Phenix reactor performed by the CEA provided a unique opportunity to have reliable test data which is very valuable in the validation and verification of a SFR system analysis code. The KAERI joined this international program of the analysis of Phenix end-of-life natural circulation test coordinated by the IAEA from 2008. The main test of natural circulation was completed in 2009. Before the test the KAERI performed the pre-test analysis based on the design condition provided by the CEA. Then, the blind post-test analysis was also performed based on the test conditions measured during the test before the CEA provide the final test results. Finally, the final post-test analysis was performed recently to predict the test results as accurate as possible. This paper introduces the modeling approach of the MARS-LMR used in the final post-test analysis and summarizes the major results of the analysis

  3. Effective Cross Section of Cold Formed Steel Column Under Axial Compression

    Science.gov (United States)

    Manikandan, P.; Pradeep, T.

    2018-06-01

    The compressive resistance of cold-formed steel (CFS) section may be governed by local, distortional or overall buckling and any apparent interaction between these modes. A new inventive stiffened CFS section is elected in this study, selected cross sections geometries and lengths are chosen such that all the types of buckling modes are met with. Buckling plot is plotted using linear elastic buckling analysis software (CUFSM). Using the test results obtained in the literature, the developed finite element model is calibrated and furthers a total of 126 parametric study is conducted such as a consequence of dimensions and the length of the cross section, thickness and yield stress. The FEA included relevant material and geometric imperfections. All the columns are analyzed under pin end conditions with axial compression. The analysis results demonstrate that the DSM equations generally assess the strength of stiffened section conservatively. Modifications to the DSM equations are recommended to evaluate the strength of stiffened section more precisely.

  4. Effective Cross Section of Cold Formed Steel Column Under Axial Compression

    Science.gov (United States)

    Manikandan, P.; Pradeep, T.

    2018-02-01

    The compressive resistance of cold-formed steel (CFS) section may be governed by local, distortional or overall buckling and any apparent interaction between these modes. A new inventive stiffened CFS section is elected in this study, selected cross sections geometries and lengths are chosen such that all the types of buckling modes are met with. Buckling plot is plotted using linear elastic buckling analysis software (CUFSM). Using the test results obtained in the literature, the developed finite element model is calibrated and furthers a total of 126 parametric study is conducted such as a consequence of dimensions and the length of the cross section, thickness and yield stress. The FEA included relevant material and geometric imperfections. All the columns are analyzed under pin end conditions with axial compression. The analysis results demonstrate that the DSM equations generally assess the strength of stiffened section conservatively. Modifications to the DSM equations are recommended to evaluate the strength of stiffened section more precisely.

  5. End-to-end interoperability and workflows from building architecture design to one or more simulations

    Science.gov (United States)

    Chao, Tian-Jy; Kim, Younghun

    2015-02-10

    An end-to-end interoperability and workflows from building architecture design to one or more simulations, in one aspect, may comprise establishing a BIM enablement platform architecture. A data model defines data entities and entity relationships for enabling the interoperability and workflows. A data definition language may be implemented that defines and creates a table schema of a database associated with the data model. Data management services and/or application programming interfaces may be implemented for interacting with the data model. Web services may also be provided for interacting with the data model via the Web. A user interface may be implemented that communicates with users and uses the BIM enablement platform architecture, the data model, the data definition language, data management services and application programming interfaces to provide functions to the users to perform work related to building information management.

  6. Validation of elastic cross section models for space radiation applications

    Energy Technology Data Exchange (ETDEWEB)

    Werneth, C.M., E-mail: charles.m.werneth@nasa.gov [NASA Langley Research Center (United States); Xu, X. [National Institute of Aerospace (United States); Norman, R.B. [NASA Langley Research Center (United States); Ford, W.P. [The University of Tennessee (United States); Maung, K.M. [The University of Southern Mississippi (United States)

    2017-02-01

    The space radiation field is composed of energetic particles that pose both acute and long-term risks for astronauts in low earth orbit and beyond. In order to estimate radiation risk to crew members, the fluence of particles and biological response to the radiation must be known at tissue sites. Given that the spectral fluence at the boundary of the shielding material is characterized, radiation transport algorithms may be used to find the fluence of particles inside the shield and body, and the radio-biological response is estimated from experiments and models. The fidelity of the radiation spectrum inside the shield and body depends on radiation transport algorithms and the accuracy of the nuclear cross sections. In a recent study, self-consistent nuclear models based on multiple scattering theory that include the option to study relativistic kinematics were developed for the prediction of nuclear cross sections for space radiation applications. The aim of the current work is to use uncertainty quantification to ascertain the validity of the models as compared to a nuclear reaction database and to identify components of the models that can be improved in future efforts.

  7. End to End Travel

    Data.gov (United States)

    US Agency for International Development — E2 Solutions is a web based end-to-end travel management tool that includes paperless travel authorization and voucher document submissions, document approval...

  8. Ends, fundamental tones and capacity of minimal submanifolds via extrinsic comparison theory

    DEFF Research Database (Denmark)

    Gimeno, Vicent; Markvorsen, Steen

    2015-01-01

    We study the volume of extrinsic balls and the capacity of extrinsic annuli in minimal submanifolds which are properly immersed with controlled radial sectional curvatures into an ambient manifold with a pole. The key results are concerned with the comparison of those volumes and capacities with ...... with the corresponding entities in a rotationally symmetric model manifold. Using the asymptotic behavior of the volumes and capacities we then obtain upper bounds for the number of ends as well as estimates for the fundamental tone of the submanifolds in question....

  9. Cross-section crushing behaviour of hat-sections (Part II: Analytical modelling)

    NARCIS (Netherlands)

    Hofmeyer, H.

    2005-01-01

    Hat-sections are often used to experimentally investigate building sheeting subject to a concentrated load and bending. In car doors, hat-sections are used for side-impact protection. Their crushing behaviour can partly be explained by only observing their cross-sectional behaviour [1]. This

  10. Extension of non-linear beam models with deformable cross sections

    Science.gov (United States)

    Sokolov, I.; Krylov, S.; Harari, I.

    2015-12-01

    Geometrically exact beam theory is extended to allow distortion of the cross section. We present an appropriate set of cross-section basis functions and provide physical insight to the cross-sectional distortion from linear elastostatics. The beam formulation in terms of material (back-rotated) beam internal force resultants and work-conjugate kinematic quantities emerges naturally from the material description of virtual work of constrained finite elasticity. The inclusion of cross-sectional deformation allows straightforward application of three-dimensional constitutive laws in the beam formulation. Beam counterparts of applied loads are expressed in terms of the original three-dimensional data. Special attention is paid to the treatment of the applied stress, keeping in mind applications such as hydrogel actuators under environmental stimuli or devices made of electroactive polymers. Numerical comparisons show the ability of the beam model to reproduce finite elasticity results with good efficiency.

  11. Angle-correlated cross sections in the framework of the continuum shell model

    International Nuclear Information System (INIS)

    Moerschel, K.P.

    1984-01-01

    In the present thesis in the framework of the continuum shell modell a concept for the treatment of angle-correlated cross sections was developed by which coincidence experiments on electron scattering on nuclei are described. For this the existing Darmstadt continuum-shell-model code had to be extended to the calculation of the correlation coefficients in which nuclear dynamics enter and which determine completely the angle-correlated cross sections. Under inclusion of the kinematics a method for the integration over the scattered electron was presented and used for the comparison with corresponding experiments. As application correlation coefficients for the proton channel in 12 C with 1 - and 2 + excitations were studied. By means of these coefficients finally cross sections for the reaction 12 C (e,p) 11 B could be calculated and compared with the experiment whereby the developed methods were proved as suitable to predict correctly both the slope and the quantity of the experimental cross sections. (orig.) [de

  12. Advanced modeling of reaction cross sections for light nuclei

    International Nuclear Information System (INIS)

    Resler, D.A.

    1991-01-01

    The shell model/R-matrix technique of calculating nuclear reaction cross sections for light projectiles incident on light nuclei is discussed, particularly in the application of the technique to thermonuclear reactions. Details are presented on the computational methods for the shell model which display how easily the calculations can be performed. Results of the shell model/R-matrix technique are discussed as are some of the problems encountered in picking an appropriate nucleon-nucleon interaction for the large model spaces which must be used for current problems. The status of our work on developing an effective nucleon-nucleon interaction for use in large-basis shell model calculations is presented. This new interaction is based on a combination of global constraints and microscopic nuclear data. 23 refs., 6 figs., 2 tabs

  13. Wall correction model for wind tunnels with open test section

    DEFF Research Database (Denmark)

    Sørensen, Jens Nørkær; Shen, Wen Zhong; Mikkelsen, Robert Flemming

    2006-01-01

    In the paper we present a correction model for wall interference on rotors of wind turbines or propellers in wind tunnels. The model, which is based on a one-dimensional momentum approach, is validated against results from CFD computations using a generalized actuator disc principle. In the model...... good agreement with the CFD computations, demonstrating that one-dimensional momentum theory is a reliable way of predicting corrections for wall interference in wind tunnels with closed as well as open cross sections....

  14. Simulation of Model Force-Loading with Changing Its Position in the Wind Tunnel Test Section

    Directory of Open Access Journals (Sweden)

    V. T. Bui

    2015-01-01

    Full Text Available When planning and implementing an aerodynamic experiment, model sizes and its position in the test section of the wind tunnel (WT play very important role. The paper focuses on the value variations of the aerodynamic characteristics of a model through changing its position in the WT test section and on the attenuation of the velocity field disturbance in front of the model. Flow around aerodynamic model profile in the open test section of the low-speed WT T-500 is simulated at BMSTU Department SM3. The problem is solved in a two-dimensional case using the ANSYS Fluent package. The mathematical model of flow is based on the Reynolds equations closed by the SST turbulence model. The paper also presents the results of the experiment. Experiments conducted in WT T-500 well correlate with the calculated data and show the optimal position in the middle of the test section when conducting the weighing and drainage experiments. Disturbance of tunnel dynamic pressure (velocity head and flow upwash around the model profile and circular cylinder in the WT test section is analyzed. It was found that flow upstream from the front stagnation point on the body weakly depends on the Reynolds number and obtained results can be used to assess the level of disturbances in the flow around a model by incompressible airflow.

  15. Design and Implementation of Radar Cross-Section Models on a Virtex-6 FPGA

    Directory of Open Access Journals (Sweden)

    B. U. V. Prashanth

    2014-01-01

    Full Text Available The simulation of radar cross-section (RCS models in FPGA is illustrated. The models adopted are the Swerling ones. Radar cross-section (RCS which is also termed as echo area gives the amount of scattered power from a target towards the radar. This paper elucidates the simulation of RCS to represent the specified targets under different conditions, namely, aspect angle and frequency. This model is used for the performance evaluation of radar. RCS models have been developed for various targets like simple objects to complex objects like aircrafts, missiles, tanks, and so forth. First, the model was developed in MATLAB real time simulation environment and after successful verification, the same was implemented in FPGA. Xilinx ISE software was used for VHDL coding. This simulation model was used for the testing of a radar system. The results were compared with MATLAB simulations and FPGA based timing diagrams and RTL synthesis. The paper illustrates the simulation of various target radar cross-section (RCS models. These models are simulated in MATLAB and in FPGA, with the aim of implementing them efficiently on a radar system. This method can be generalized to apply to objects of arbitrary geometry for the two configurations of transmitter and receiver in the same as well as different locations.

  16. Photo-neutron reaction cross-section for 93Nb in the end-point bremsstrahlung energies of 12–16 and 45–70 MeV

    International Nuclear Information System (INIS)

    Naik, H.; Kim, G.N.; Schwengner, R.; Kim, K.; Zaman, M.; Tatari, M.; Sahid, M.; Yang, S.C.; John, R.; Massarczyk, R.; Junghans, A.; Shin, S.G.; Key, Y.; Wagner, A.; Lee, M.W.; Goswami, A.; Cho, M.-H.

    2013-01-01

    The photo-neutron cross-sections of 93 Nb at the end-point bremsstrahlung energies of 12, 14 and 16 MeV as well as 45, 50, 55, 60 and 70 MeV have been determined by the activation and the off-line γ-ray spectrometric techniques using the 20 MeV electron linac (ELBE) at Helmholtz-Zentrum Dresden-Rossendorf (HZDR), Dresden, Germany, and 100 MeV electron linac at Pohang Accelerator Laboratory (PAL), Pohang, Korea. The 93 Nb(γ, xn, x=1–4) reaction cross-sections as a function of photon energy were also calculated using computer code TALYS 1.4. The flux-weighted average values were obtained from the experimental and the theoretical (TALYS) values based on mono-energetic photons. The experimental values of present work are in good agreement with the flux-weighted theoretical values of TALYS 1.4 but are slightly higher than the flux-weighted experimental data of mono-energetic photons. It was also found that the theoretical and the experimental values of present work and literature data for the 93 Nb(γ, xn) reaction cross-sections increase from the threshold values to a certain energy, where other reaction channels opens. However, the increase of 93 Nb(γ, n) and 93 Nb(γ, 2n) reaction cross-sections are sharper compared to 93 Nb(γ, 3n) and 93 Nb(γ, 4n) reaction cross-sections. The sharp increase of 93 Nb(γ, n) and 93 Nb(γ, 2n) reaction cross-sections from the threshold value up to 17–22 MeV is due to the Giant Dipole Resonance (GDR) effect besides the role of excitation energy. After a certain values, the individual 93 Nb(γ, xn) reaction cross-sections decrease with increase of bremsstrahlung energy due to opening of other reaction channels

  17. Investigation on macroscopic cross section model for BWR pin-by-pin core analysis - 118

    International Nuclear Information System (INIS)

    Fujita, T.; Tada, K.; Yamamoto, A.; Yamane, Y.; Kosaka, S.; Hirano, G.

    2010-01-01

    A cross section model used in the pin-by-pin core analysis for BWR is investigated. In the pin-by-pin core calculation method, pin-cell averaged cross sections are calculated for many combinations of state and history variables that have influences on the cross section and are tabulated prior to the core calculations. Variation of a cross section in a core simulator is classified into two different types, i.e., the instantaneous effect and the history effect. The instantaneous effect is incorporated by the variation of cross section which is caused by the instantaneous change of state variables. For this effect, the exposure, the void fraction, the fuel temperature, the moderator temperature and the control rod are used as indexes. The history effect is the cumulative effect of state variables. We treat this effect with a unified approach using the spectral history. To confirm accuracy of the cross section model, the pin-by-pin fission rate distribution and the k-infinity of fuel assembly which are obtained with the tabulated and the reference cross sections are compared. For the instantaneous effect, the present cross section model well reproduces the reference results for all off-nominal conditions. For the history effect, however, considerable differences both on the pin-by-pin fission rate distribution and the k-infinity are observed at high exposure points. (authors)

  18. 30 CFR 75.1438 - End attachment replacement.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false End attachment replacement. 75.1438 Section 75.1438 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND... attachment replacement. Wire rope attachments shall be replaced when cracked, deformed, or excessively worn. ...

  19. A Three End-Member Mixing Model Based on Isotopic Composition and Elemental Ratio

    Directory of Open Access Journals (Sweden)

    Kon-Kee Liu Shuh-Ji Kao

    2007-01-01

    Full Text Available A three end-member mixing model based on nitrogen isotopic composition and organic carbon to nitrogen ratio of suspended particulate matter in an aquatic environment has been developed. Mathematical expressions have been derived for the calculation of the fractions of nitrogen or organic carbon originating from three different sources of distinct isotopic and elemental compositions. The model was successfully applied to determine the contributions from anthropogenic wastes, soils and bedrock-derived sediments to particulate nitrogen and particulate organic carbon in the Danshuei River during the flood caused by Typhoon Bilis in August 2000. The model solutions have been expressed in a general form that allows applications to mixtures with other types of isotopic compositions and elemental ratios or in forms other than suspended particulate matter.

  20. Validation of models that predict Cesarean section after induction of labor

    NARCIS (Netherlands)

    Verhoeven, C. J. M.; Oudenaarden, A.; Hermus, M. A. A.; Porath, M. M.; Oei, S. G.; Mol, B. W. J.

    2009-01-01

    Objective Models for the prediction of Cesarean delivery after induction of labor can be used to improve clinical decision-making. The objective of this study was to validate two existing models, published by Peregrine et al. and Rane et al., for the prediction of Cesarean section after induction of

  1. End-to-side and end-to-end anastomoses give similar results in cervical oesophagogastrostomy.

    Science.gov (United States)

    Pierie, J P; De Graaf, P W; Poen, H; Van Der Tweel, I; Obertop, H

    1995-12-01

    To find out if there were any differences in healing between end-to-end and end-to-side anastomoses for oesophagogastrostomy. Open study with historical controls. University hospital, The Netherlands. 28 patients with end-to-end and 90 patients with end-to-side anastomoses after transhiatal oesophagectomy and partial gastrectomy for cancer of the oesophagus or oesophagogastric junction, with gastric tube reconstruction and cervical anastomosis. Leak and stricture rates, and the number of dilatations needed to relieve dysphagia. There were no significant differences in leak rates (end-to-end 4/28, 14%, and end-to-side 13/90, 14%) or anastomotic strictures (end-to-end 9/28, 32%, and end-to-side 26/90, 29%). The median number of dilatations needed to relieve dysphagia was 7 (1-33) after end-to-end and 9 (1-113) after end-to-side oesophagogastrostomy. There were no differences between the two methods of suture of cervical oesophagogastrostomy when leakage, stricture, and number of dilatations were used as criteria of good healing.

  2. Josephson cross-sectional model experiment

    International Nuclear Information System (INIS)

    Ketchen, M.B.; Herrell, D.J.; Anderson, C.J.

    1985-01-01

    This paper describes the electrical design and evaluation of the Josephson cross-sectional model (CSM) experiment. The experiment served as a test vehicle to verify the operation at liquid-helium temperatures of Josephson circuits integrated in a package environment suitable for high-performance digital applications. The CSM consisted of four circuit chips assembled on two cards in a three-dimensional card-on-board package. The chips (package) were fabricated in a 2.5-μm (5-μm) minimum linewidth Pb-alloy technology. A hierarchy of solder and pluggable connectors was used to attach the parts together and to provide electrical interconnections between parts. A data path which simulated a jump control sequence and a cache access in each machine cycle was successfully operated with cycle times down to 3.7 ns. The CSM incorporated the key components of the logic, power, and package of a prototype Josephson signal processor and demonstrated the feasibility of making such a processor with a sub-4-ns cycle time

  3. PBTK modeling demonstrates contribution of dermal and inhalation exposure components to end-exhaled breath concentrations of naphthalene.

    Science.gov (United States)

    Kim, David; Andersen, Melvin E; Chao, Yi-Chun E; Egeghy, Peter P; Rappaport, Stephen M; Nylander-French, Leena A

    2007-06-01

    Dermal and inhalation exposure to jet propulsion fuel 8 (JP-8) have been measured in a few occupational exposure studies. However, a quantitative understanding of the relationship between external exposures and end-exhaled air concentrations has not been described for occupational and environmental exposure scenarios. Our goal was to construct a physiologically based toxicokinetic (PBTK) model that quantitatively describes the relative contribution of dermal and inhalation exposures to the end-exhaled air concentrations of naphthalene among U.S. Air Force personnel. The PBTK model comprised five compartments representing the stratum corneum, viable epidermis, blood, fat, and other tissues. The parameters were optimized using exclusively human exposure and biological monitoring data. The optimized values of parameters for naphthalene were a) permeability coefficient for the stratum corneum 6.8 x 10(-5) cm/hr, b) permeability coefficient for the viable epidermis 3.0 x 10(-3) cm/hr, c) fat:blood partition coefficient 25.6, and d) other tissue:blood partition coefficient 5.2. The skin permeability coefficient was comparable to the values estimated from in vitro studies. Based on simulations of workers' exposures to JP-8 during aircraft fuel-cell maintenance operations, the median relative contribution of dermal exposure to the end-exhaled breath concentration of naphthalene was 4% (10th percentile 1% and 90th percentile 11%). PBTK modeling allowed contributions of the end-exhaled air concentration of naphthalene to be partitioned between dermal and inhalation routes of exposure. Further study of inter- and intraindividual variations in exposure assessment is required to better characterize the toxicokinetic behavior of JP-8 components after occupational and/or environmental exposures.

  4. Measurements of the effective thermal neutron absorption cross-section in multi-grain models

    International Nuclear Information System (INIS)

    Drozdowicz, K.; Gabanska, B.; Igielski, A.; Krynicka, E.; Schneider, K.; Woznicka, U.

    2005-01-01

    The effective macroscopic absorption cross-section Σ a eff of thermal neutrons in a grained medium differs from the corresponding cross-section Σ a hom in the homogeneous medium consisting of the same components, contributing in the same amounts. The ratio of these cross-sections defines the grain parameter, G, which is a measure of heterogeneity of the system for neutron absorption. Heterogeneous models have been built as two- or three-component systems (Ag, Cu and Co 3 O 4 grains distributed in a regular grid in Plexiglas, in various proportions between them). The effective absorption cross-section has been measured and the experimental grain parameter has been found for each model. The obtained values are in the interval 0.34 < G < 0.58, while G = 1 means the homogeneous material. (author)

  5. End points and assessments in esthetic dental treatment.

    Science.gov (United States)

    Ishida, Yuichi; Fujimoto, Keiko; Higaki, Nobuaki; Goto, Takaharu; Ichikawa, Tetsuo

    2015-10-01

    There are two key considerations for successful esthetic dental treatments. This article systematically describes the two key considerations: the end points of esthetic dental treatments and assessments of esthetic outcomes, which are also important for acquiring clinical skill in esthetic dental treatments. The end point and assessment of esthetic dental treatment were discussed through literature reviews and clinical practices. Before designing a treatment plan, the end point of dental treatment should be established. The section entitled "End point of esthetic dental treatment" discusses treatments for maxillary anterior teeth and the restoration of facial profile with prostheses. The process of assessing treatment outcomes entitled "Assessments of esthetic dental treatment" discusses objective and subjective evaluation methods. Practitioners should reach an agreement regarding desired end points with patients through medical interviews, and continuing improvements and developments of esthetic assessments are required to raise the therapeutic level of esthetic dental treatments. Copyright © 2015 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

  6. SPoRT - An End-to-End R2O Activity

    Science.gov (United States)

    Jedlovec, Gary J.

    2009-01-01

    Established in 2002 to demonstrate the weather and forecasting application of real-time EOS measurements, the Short-term Prediction Research and Transition (SPoRT) program has grown to be an end-to-end research to operations activity focused on the use of advanced NASA modeling and data assimilation approaches, nowcasting techniques, and unique high-resolution multispectral observational data applications from EOS satellites to improve short-term weather forecasts on a regional and local scale. SPoRT currently partners with several universities and other government agencies for access to real-time data and products, and works collaboratively with them and operational end users at 13 WFOs to develop and test the new products and capabilities in a "test-bed" mode. The test-bed simulates key aspects of the operational environment without putting constraints on the forecaster workload. Products and capabilities which show utility in the test-bed environment are then transitioned experimentally into the operational environment for further evaluation and assessment. SPoRT focuses on a suite of data and products from MODIS, AMSR-E, and AIRS on the NASA Terra and Aqua satellites, and total lightning measurements from ground-based networks. Some of the observations are assimilated into or used with various versions of the WRF model to provide supplemental forecast guidance to operational end users. SPoRT is enhancing partnerships with NOAA / NESDIS for new product development and data access to exploit the remote sensing capabilities of instruments on the NPOESS satellites to address short term weather forecasting problems. The VIIRS and CrIS instruments on the NPP and follow-on NPOESS satellites provide similar observing capabilities to the MODIS and AIRS instruments on Terra and Aqua. SPoRT will be transitioning existing and new capabilities into the AWIIPS II environment to continue the continuity of its activities.

  7. Three Software Tools for Viewing Sectional Planes, Volume Models, and Surface Models of a Cadaver Hand.

    Science.gov (United States)

    Chung, Beom Sun; Chung, Min Suk; Shin, Byeong Seok; Kwon, Koojoo

    2018-02-19

    The hand anatomy, including the complicated hand muscles, can be grasped by using computer-assisted learning tools with high quality two-dimensional images and three-dimensional models. The purpose of this study was to present up-to-date software tools that promote learning of stereoscopic morphology of the hand. On the basis of horizontal sectioned images and outlined images of a male cadaver, vertical planes, volume models, and surface models were elaborated. Software to browse pairs of the sectioned and outlined images in orthogonal planes and software to peel and rotate the volume models, as well as a portable document format (PDF) file to select and rotate the surface models, were produced. All of the software tools were downloadable free of charge and usable off-line. The three types of tools for viewing multiple aspects of the hand could be adequately employed according to individual needs. These new tools involving the realistic images of a cadaver and the diverse functions are expected to improve comprehensive knowledge of the hand shape. © 2018 The Korean Academy of Medical Sciences.

  8. Mucociliary clearance following tracheal resection and end-to-end anastomosis.

    Science.gov (United States)

    Toomes, H; Linder, A

    1989-10-01

    Mucociliary clearance is an important cleaning system of the bronchial tree. The complex transport system reacts sensitively to medicinal stimuli and inhaled substances. A disturbance causes secretion retention which encourages the development of acute and chronic pulmonary diseases. It is not yet known in which way sectional resection of the central airway effects mucociliary clearance. A large number of the surgical failures are attributable to septic complications in the area of the anastomosis. In order to study the transportation process over the anastomosis, ten dogs underwent a tracheal resection with end-to-end anastomosis, and the mucociliary activity was recorded using a bronchoscopic video-technical method. Recommencement of mucous transport was observed on the third, and transport over the anastomosis from the sixth to tenth, postoperative days. The mucociliary clearance had completely recovered on the twenty-first day in the majority of dogs. Histological examination of the anastomoses nine months postoperatively showed a flat substitute epithelium without cilia-bearing cells in all dogs. This contrasts with the quick restitution of the transport function. In case of undamaged respiratory mucosa, a good adaptation of the resection margins suffices for the mucous film to slide over the anastomosis.

  9. WiMAX security and quality of service an end-to-end perspective

    CERN Document Server

    Tang, Seok-Yee; Sharif, Hamid

    2010-01-01

    WiMAX is the first standard technology to deliver true broadband mobility at speeds that enable powerful multimedia applications such as Voice over Internet Protocol (VoIP), online gaming, mobile TV, and personalized infotainment. WiMAX Security and Quality of Service, focuses on the interdisciplinary subject of advanced Security and Quality of Service (QoS) in WiMAX wireless telecommunication systems including its models, standards, implementations, and applications. Split into 4 parts, Part A of the book is an end-to-end overview of the WiMAX architecture, protocol, and system requirements.

  10. Interfaces for End-User Information Seeking.

    Science.gov (United States)

    Marchionini, Gary

    1992-01-01

    Discusses essential features of interfaces to support end-user information seeking. Highlights include cognitive engineering; task models and task analysis; the problem-solving nature of information seeking; examples of systems for end-users, including online public access catalogs (OPACs), hypertext, and help systems; and suggested research…

  11. End effects on elbows subjected to moment loadings

    International Nuclear Information System (INIS)

    Rodabaugh, E.C.; Moore, S.E.

    1982-01-01

    So-called end effects for moment loadings on short-radius and long-radius butt welding elbows of various arc lengths are investigated with a view toward providing more accurate design formulas for critical piping systems. Data developed in this study, along with published information, were used to develop relatively simple design equations for elbows attached at both ends to long sections of straight pipe. These formulas are the basis for an alternate ASME Code procedure for evaluating the bending moment stresses in Class 1 nuclear piping (ASME Code Case N-319). The more complicated problems of elbows with other end conditions, e.g., flanges at one or both ends, are also considered. Comparisons of recently published experimental and theoretical studies with current industrial code design rules for these situations indicate that these rules also need to be improved

  12. Combined fishing and climate forcing in the southern Benguela upwelling ecosystem: an end-to-end modelling approach reveals dampened effects.

    Directory of Open Access Journals (Sweden)

    Morgane Travers-Trolet

    Full Text Available The effects of climate and fishing on marine ecosystems have usually been studied separately, but their interactions make ecosystem dynamics difficult to understand and predict. Of particular interest to management, the potential synergism or antagonism between fishing pressure and climate forcing is analysed in this paper, using an end-to-end ecosystem model of the southern Benguela ecosystem, built from coupling hydrodynamic, biogeochemical and multispecies fish models (ROMS-N2P2Z2D2-OSMOSE. Scenarios of different intensities of upwelling-favourable wind stress combined with scenarios of fishing top-predator fish were tested. Analyses of isolated drivers show that the bottom-up effect of the climate forcing propagates up the food chain whereas the top-down effect of fishing cascades down to zooplankton in unfavourable environmental conditions but dampens before it reaches phytoplankton. When considering both climate and fishing drivers together, it appears that top-down control dominates the link between top-predator fish and forage fish, whereas interactions between the lower trophic levels are dominated by bottom-up control. The forage fish functional group appears to be a central component of this ecosystem, being the meeting point of two opposite trophic controls. The set of combined scenarios shows that fishing pressure and upwelling-favourable wind stress have mostly dampened effects on fish populations, compared to predictions from the separate effects of the stressors. Dampened effects result in biomass accumulation at the top predator fish level but a depletion of biomass at the forage fish level. This should draw our attention to the evolution of this functional group, which appears as both structurally important in the trophic functioning of the ecosystem, and very sensitive to climate and fishing pressures. In particular, diagnoses considering fishing pressure only might be more optimistic than those that consider combined effects

  13. [3-dimensional models of actual or simulated cesarean sections].

    Science.gov (United States)

    Patzak, B; Schaller, A

    2001-01-01

    Following upon an etymological and historical introduction, this report refers to two three-dimensional wax models of Caesarean sections, which have recently been acquired by the Pathological-anatomical Federal Museum in Vienna. Information is given on origin, dating and kind of production; questions of indication and operation technique, and--when in doubt--obduction technique, are being considered.

  14. Combining interviewing and modeling for end-user energy conservation

    International Nuclear Information System (INIS)

    Goldblatt, David L.; Hartmann, Christoph; Duerrenberger, Gregor

    2005-01-01

    Studying energy consumption through the lens of households is an increasingly popular research avenue. This paper focuses on residential end-user energy conservation. It describes an approach that combines energy modeling and in-depth interviews for communicating about energy use and revealing consumer preferences for change at different levels and intervention points. Expert knowledge was embodied in a computer model for householders that calculates an individual's current energy consumption and helps assess personal savings potentials, while also bringing in socio-technical and economic elements beyond the user's direct control. The paper gives a detailed account of this computer information tool developed for interviewing purposes. It then describes the interview guidelines, data analysis, and main results. In general, interview subjects overestimated the environmental friendliness of their lifestyles. After experience with the program, they tended to rate external (technological, societal) factors as somewhat stronger determinants of their consumption levels than personal (behavioral and household investment) factors, with the notable exception of mobility. Concerning long-term energy perspectives, the majority of subjects felt that society has the ability to make a collective choice towards significantly lower energy consumption levels. Interviewees confirmed that the software and interactive sessions helped them think more holistically about the personal, social, and technological dimensions of energy conservation. Lessons can be applied to the development of future energy communication tools

  15. End-to-End Neural Optical Music Recognition of Monophonic Scores

    Directory of Open Access Journals (Sweden)

    Jorge Calvo-Zaragoza

    2018-04-01

    Full Text Available Optical Music Recognition is a field of research that investigates how to computationally decode music notation from images. Despite the efforts made so far, there are hardly any complete solutions to the problem. In this work, we study the use of neural networks that work in an end-to-end manner. This is achieved by using a neural model that combines the capabilities of convolutional neural networks, which work on the input image, and recurrent neural networks, which deal with the sequential nature of the problem. Thanks to the use of the the so-called Connectionist Temporal Classification loss function, these models can be directly trained from input images accompanied by their corresponding transcripts into music symbol sequences. We also present the Printed Music Scores dataset, containing more than 80,000 monodic single-staff real scores in common western notation, that is used to train and evaluate the neural approach. In our experiments, it is demonstrated that this formulation can be carried out successfully. Additionally, we study several considerations about the codification of the output musical sequences, the convergence and scalability of the neural models, as well as the ability of this approach to locate symbols in the input score.

  16. Interval-parameter chance-constraint programming model for end-of-life vehicles management under rigorous environmental regulations.

    Science.gov (United States)

    Simic, Vladimir

    2016-06-01

    As the number of end-of-life vehicles (ELVs) is estimated to increase to 79.3 million units per year by 2020 (e.g., 40 million units were generated in 2010), there is strong motivation to effectively manage this fast-growing waste flow. Intensive work on management of ELVs is necessary in order to more successfully tackle this important environmental challenge. This paper proposes an interval-parameter chance-constraint programming model for end-of-life vehicles management under rigorous environmental regulations. The proposed model can incorporate various uncertainty information in the modeling process. The complex relationships between different ELV management sub-systems are successfully addressed. Particularly, the formulated model can help identify optimal patterns of procurement from multiple sources of ELV supply, production and inventory planning in multiple vehicle recycling factories, and allocation of sorted material flows to multiple final destinations under rigorous environmental regulations. A case study is conducted in order to demonstrate the potentials and applicability of the proposed model. Various constraint-violation probability levels are examined in detail. Influences of parameter uncertainty on model solutions are thoroughly investigated. Useful solutions for the management of ELVs are obtained under different probabilities of violating system constraints. The formulated model is able to tackle a hard, uncertainty existing ELV management problem. The presented model has advantages in providing bases for determining long-term ELV management plans with desired compromises between economic efficiency of vehicle recycling system and system-reliability considerations. The results are helpful for supporting generation and improvement of ELV management plans. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Flexural Behavior of Concrete Beam Strengthened by Near-Surface Mounted CFRP Reinforcement Using Equivalent Section Model

    Directory of Open Access Journals (Sweden)

    Woo-tai Jung

    2017-01-01

    Full Text Available FRP (fiber reinforced polymer has found wide applications as an alternative to steel rebar not only for the repair and strengthening of existing structures but also for the erection of new structures. Near-surface mounted (NSM strengthening was introduced as an alternative of externally bonded reinforcement (EBR but this method also experiences early bond failure, which stresses the importance of predicting accurately the bond failure behavior in order to evaluate precisely the performance of NSM reinforcement. This study proposes the equivalent section model assuming monolithic behavior of the filler and CFRP reinforcement. This equivalent section model enables establishing a bond failure model applicable independently of the sectional shape of the CFRP reinforcement. This so-derived bond failure model is then validated experimentally by means of beams flexure-strengthened by NSM CFRP reinforcements with various cross-sections. Finally, analytical analysis applying the bond failure model considering the equivalent section and defined failure criteria is performed. The results show the accuracy of the prediction of the failure mode as well as the accurate prediction of the experimental results regardless of the sectional shape of the CFRP reinforcement.

  18. Optimal urban water conservation strategies considering embedded energy: coupling end-use and utility water-energy models.

    Science.gov (United States)

    Escriva-Bou, A.; Lund, J. R.; Pulido-Velazquez, M.; Spang, E. S.; Loge, F. J.

    2014-12-01

    Although most freshwater resources are used in agriculture, a greater amount of energy is consumed per unit of water supply for urban areas. Therefore, efforts to reduce the carbon footprint of water in cities, including the energy embedded within household uses, can be an order of magnitude larger than for other water uses. This characteristic of urban water systems creates a promising opportunity to reduce global greenhouse gas emissions, particularly given rapidly growing urbanization worldwide. Based on a previous Water-Energy-CO2 emissions model for household water end uses, this research introduces a probabilistic two-stage optimization model considering technical and behavioral decision variables to obtain the most economical strategies to minimize household water and water-related energy bills given both water and energy price shocks. Results show that adoption rates to reduce energy intensive appliances increase significantly, resulting in an overall 20% growth in indoor water conservation if household dwellers include the energy cost of their water use. To analyze the consequences on a utility-scale, we develop an hourly water-energy model based on data from East Bay Municipal Utility District in California, including the residential consumption, obtaining that water end uses accounts for roughly 90% of total water-related energy, but the 10% that is managed by the utility is worth over 12 million annually. Once the entire end-use + utility model is completed, several demand-side management conservation strategies were simulated for the city of San Ramon. In this smaller water district, roughly 5% of total EBMUD water use, we found that the optimal household strategies can reduce total GHG emissions by 4% and utility's energy cost over 70,000/yr. Especially interesting from the utility perspective could be the "smoothing" of water use peaks by avoiding daytime irrigation that among other benefits might reduce utility energy costs by 0.5% according to our

  19. M5 model tree based predictive modeling of road accidents on non-urban sections of highways in India.

    Science.gov (United States)

    Singh, Gyanendra; Sachdeva, S N; Pal, Mahesh

    2016-11-01

    This work examines the application of M5 model tree and conventionally used fixed/random effect negative binomial (FENB/RENB) regression models for accident prediction on non-urban sections of highway in Haryana (India). Road accident data for a period of 2-6 years on different sections of 8 National and State Highways in Haryana was collected from police records. Data related to road geometry, traffic and road environment related variables was collected through field studies. Total two hundred and twenty two data points were gathered by dividing highways into sections with certain uniform geometric characteristics. For prediction of accident frequencies using fifteen input parameters, two modeling approaches: FENB/RENB regression and M5 model tree were used. Results suggest that both models perform comparably well in terms of correlation coefficient and root mean square error values. M5 model tree provides simple linear equations that are easy to interpret and provide better insight, indicating that this approach can effectively be used as an alternative to RENB approach if the sole purpose is to predict motor vehicle crashes. Sensitivity analysis using M5 model tree also suggests that its results reflect the physical conditions. Both models clearly indicate that to improve safety on Indian highways minor accesses to the highways need to be properly designed and controlled, the service roads to be made functional and dispersion of speeds is to be brought down. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Circumferential resection and "Z"-shape plastic end-to-end anastomosis of canine trachea.

    Science.gov (United States)

    Zhao, H; Li, Z; Fang, J; Fang, C

    1999-03-01

    To prevent anastomotic stricture of the trachea. Forty young mongrel dogs, weighing 5-7 kg, were randomly divided into two groups: experimental group and control group, with 20 dogs in each group. Four tracheal rings were removed from each dog. In the experimental group, two "Z"-shape tracheoplastic anastomoses were performed on each dog, one on the anterior wall and the other on the membranous part of the trachea. In the control group, each dog received only simple end-to-end anastomosis. Vicryl 3-0 absorbable suture and OB fibrin glue were used for both groups. All dogs were killed when their body weight doubled. The average sagittal stenotic ratio were 1.20 +/- 0.12 for the experimental group and 0.83 +/- 0.05 for the control group. The average cross-sectional area stenotic ratio were 0.90 +/- 0.12 and 0.69 +/- 0.09 and T values were 8.71 and 4.57 for the two groups (P anastomosis in preventing anastomotic stricture of canine trachea.

  1. Optical and statistical model calculation of the americium 242m capture cross section

    International Nuclear Information System (INIS)

    Tellier, Henry.

    1981-04-01

    The capture cross sections of Am 242m can be deduced from resonances analysis at low energy and computed with theoretical models at high energy. In this work, a coherent set of cross sections which reproduced the experimental values of the fission cross sections is computed. These calculations were performed for an energy of the incoming neutron between 1 keV and 1 MeV

  2. cmpXLatt: Westinghouse automated testing tool for nodal cross section models

    International Nuclear Information System (INIS)

    Guimaraes, Petri Forslund; Rönnberg, Kristian

    2011-01-01

    The procedure for evaluating the merits of different nodal cross section representation models is normally both cumbersome and time consuming, and includes many manual steps when preparing appropriate benchmark problems. Therefore, a computer tool called cmpXLatt has been developed at Westinghouse in order to facilitate the process of performing comparisons between nodal diffusion theory results and corresponding transport theory results on a single node basis. Due to the large number of state points that can be evaluated by cmpXLatt, a systematic and comprehensive way of performing verification and validation of nodal cross section models is provided. This paper presents the main features of cmpXLatt and demonstrates the benefits of using cmpXLatt in a real life application. (author)

  3. α -induced reactions on 115In: Cross section measurements and statistical model analysis

    Science.gov (United States)

    Kiss, G. G.; Szücs, T.; Mohr, P.; Török, Zs.; Huszánk, R.; Gyürky, Gy.; Fülöp, Zs.

    2018-05-01

    Background: α -nucleus optical potentials are basic ingredients of statistical model calculations used in nucleosynthesis simulations. While the nucleon+nucleus optical potential is fairly well known, for the α +nucleus optical potential several different parameter sets exist and large deviations, reaching sometimes even an order of magnitude, are found between the cross section predictions calculated using different parameter sets. Purpose: A measurement of the radiative α -capture and the α -induced reaction cross sections on the nucleus 115In at low energies allows a stringent test of statistical model predictions. Since experimental data are scarce in this mass region, this measurement can be an important input to test the global applicability of α +nucleus optical model potentials and further ingredients of the statistical model. Methods: The reaction cross sections were measured by means of the activation method. The produced activities were determined by off-line detection of the γ rays and characteristic x rays emitted during the electron capture decay of the produced Sb isotopes. The 115In(α ,γ )119Sb and 115In(α ,n )Sb118m reaction cross sections were measured between Ec .m .=8.83 and 15.58 MeV, and the 115In(α ,n )Sb118g reaction was studied between Ec .m .=11.10 and 15.58 MeV. The theoretical analysis was performed within the statistical model. Results: The simultaneous measurement of the (α ,γ ) and (α ,n ) cross sections allowed us to determine a best-fit combination of all parameters for the statistical model. The α +nucleus optical potential is identified as the most important input for the statistical model. The best fit is obtained for the new Atomki-V1 potential, and good reproduction of the experimental data is also achieved for the first version of the Demetriou potentials and the simple McFadden-Satchler potential. The nucleon optical potential, the γ -ray strength function, and the level density parametrization are also

  4. Home-end and activity-end preferences for access to and egress from train stations in the Copenhagen region

    DEFF Research Database (Denmark)

    Halldórsdóttir, Katrín; Nielsen, Otto Anker; Prato, Carlo Giacomo

    2017-01-01

    . Moreover, model results emphasize the role of bicycle parking in terms of the sheer number of spaces to be increased as well as covered places to be offered at the activity end, de facto giving the possibility to leave a bicycle at that end during the night. Lastly, model results show that it is a matter......Increasing public transport use with the aim of improving the sustainability of cities should focus not only on enhancing level and quality of the service offered, but also on understanding determinants of the choice of access and egress modes to and from the railway network. This study analyzes...... the difference in preferences at the home-end and activity-end for travelers who have chosen train as their main travel mode while investigating the effect of policy variables such as car parking availability, bicycle parking availability and type, and bicycle on train possibility. Specifically, this study...

  5. Models of conflict and cooperation

    CERN Document Server

    Gillman, Rick

    2009-01-01

    Models of Conflict and Cooperation is a comprehensive, introductory, game theory text for general undergraduate students. As a textbook, it provides a new and distinctive experience for students working to become quantitatively literate. Each chapter begins with a "dialogue" that models quantitative discourse while previewing the topics presented in the rest of the chapter. Subsequent sections develop the key ideas starting with basic models and ending with deep concepts and results. Throughout all of the sections, attention is given to promoting student engagement with the material through re

  6. Wall Correction Model for Wind Tunnels with Open Test Section

    DEFF Research Database (Denmark)

    Sørensen, Jens Nørkær; Shen, Wen Zhong; Mikkelsen, Robert Flemming

    2004-01-01

    , the corrections from the model are in very good agreement with the CFD computaions, demonstrating that one-dimensional momentum theory is a reliable way of predicting corrections for wall interference in wind tunnels with closed as well as open cross sections. Keywords: Wind tunnel correction, momentum theory...

  7. Development of an end-of-life vehicle recovery model using system dynamics and future research needs

    Science.gov (United States)

    Mohamad-Ali, N.; Ghazilla, R. A. R.; Abdul-Rashid, S. H.; Sakundarini, N.; Ahmad-Yazid, A.; Stephenie, L.

    2017-06-01

    The implementation of end-of-life vehicle (ELV) recovery policy in Malaysia has led vehicle manufacturers to look at different ways to improve design and development of vehicles. Nowadays, it is crucial to incorporate end-of-life (EOL) design strategies into the vehicle design in order to enhance the effectiveness of the ELV recovery network. Although recent studies have shown that product design has a significant effect on the product recovery rate, there is a lack of studies on how EOL design strategies affects the effectiveness of ELV recovery, particularly when there are dynamic changes in the behaviour of the product recovery network. Thus, in this study, we developed a preliminary model based on the system dynamics approach in order to predict the effectiveness of ELV recovery in response to dynamic changes of various factors (including EOL design strategies) in the business environment. We developed this model based on preliminary data that we had gathered from unstructured interviews with the key stakeholders of ELV management in Malaysia. We believe that our model will greatly benefit product designers in incorporating the appropriate EOL design strategies in order to boost ELV recovery effectiveness in Malaysia.

  8. Evaluation of multisectional and two-section particulate matter photochemical grid models in the Western United States.

    Science.gov (United States)

    Morris, Ralph; Koo, Bonyoung; Yarwood, Greg

    2005-11-01

    Version 4.10s of the comprehensive air-quality model with extensions (CAMx) photochemical grid model has been developed, which includes two options for representing particulate matter (PM) size distribution: (1) a two-section representation that consists of fine (PM2.5) and coarse (PM2.5-10) modes that has no interactions between the sections and assumes all of the secondary PM is fine; and (2) a multisectional representation that divides the PM size distribution into N sections (e.g., N = 10) and simulates the mass transfer between sections because of coagulation, accumulation, evaporation, and other processes. The model was applied to Southern California using the two-section and multisection representation of PM size distribution, and we found that allowing secondary PM to grow into the coarse mode had a substantial effect on PM concentration estimates. CAMx was then applied to the Western United States for the 1996 annual period with a 36-km grid resolution using both the two-section and multisection PM representation. The Community Multiscale Air Quality (CMAQ) and Regional Modeling for Aerosol and Deposition (REMSAD) models were also applied to the 1996 annual period. Similar model performance was exhibited by the four models across the Interagency Monitoring of Protected Visual Environments (IMPROVE) and Clean Air Status and Trends Network monitoring networks. All four of the models exhibited fairly low annual bias for secondary PM sulfate and nitrate but with a winter overestimation and summer underestimation bias. The CAMx multisectional model estimated that coarse mode secondary sulfate and nitrate typically contribute nitrate when averaged across the more rural IMPROVE monitoring network.

  9. 2008 annual meeting on nuclear technology. Pt. 1. Section reports

    International Nuclear Information System (INIS)

    Dagan, Ron; Sanchez Espinoza, Victor Hugo; Faber, Wolfgang; Berlepsch, Thilo v.; Spann, Holger; Schaffrath, Andreas; Schubert, Bernd; Rieger, Udo; Christ, Bernhard G.; Gulden, Werner; Bogusch, Edgar

    2008-01-01

    Summary report on these 5 - out of 11 - Sections of the Annual Conference on Nuclear Technology held in Hamburg on May 27-29, 2008: - Reactor Physics and Methods of Calculation - Thermodynamics and Fluid Dynamics - Safety of Nuclear Installations - Methods, Analysis, Results - Front End and Back End of the Fuel Cycle, Radioactive Waste, Storage - Fusion Technology. Other Sections will be covered in reports in further issues of atw. (orig.)

  10. Simultaneous Feedback Models with Macro-Comparative Cross-Sectional Data

    Directory of Open Access Journals (Sweden)

    Nate Breznau

    2018-06-01

    Full Text Available Social scientists often work with theories of reciprocal causality. Sometimes theories suggest that reciprocal causes work simultaneously, or work on a time-scale small enough to make them appear simultaneous. Researchers may employ simultaneous feedback models to investigate such theories, although the practice is rare in cross-sectional survey research. This paper discusses the certain conditions that make these models possible if not desirable using such data. This methodological excursus covers the construction of simultaneous feedback models using a structural equation modeling perspective. This allows the researcher to test if a simultaneous feedback theory fits survey data, test competing hypotheses and engage in macro-comparisons. This paper presents methods in a manner and language amenable to the practicing social scientist who is not a statistician or matrix mathematician. It demonstrates how to run models using three popular software programs (MPlus, Stata and R, and an empirical example using International Social Survey Program data.

  11. Electronic Nicotine Delivery Systems (ENDS): Mapping the Indian Online Retail Market.

    Science.gov (United States)

    Mohanty, Vikrant R; Chahar, Puneet; Balappanavar, Aswini Y; Yadav, Vipul

    2017-11-01

    Motivating tobacco consumers to change their behavior, and harm reduction strategies, are the predominant traditional approaches to tobacco cessation. Recent trends worldwide have shown the emergence of Electronic Nicotine Delivery Systems (ENDS), such as electronic cigarettes (e-cigarettes), as a purported harm reduction strategy to traditional cigarettes. Considering the global rise in the popularity of ENDS, our study aims to survey the online retail market for ENDS in India. The current study was conducted in September-October, 2015 and 4 keywords were used to search Google India to identify online retail websites marketing ENDS. Each website was searched using the same keywords and all specific website pages displaying ENDS models were considered. Thus, data was obtained for various measures of ENDS present on the model descriptions. A total of 6 retail shopping websites were searched which revealed 65 different models of ENDS (34 brands). Forty-five models (69%) were flavored and 21 models (33%) mentioned about nicotine strengths. Seventeen models (26%) provided health warnings in their product descriptions. "No tar no tobacco" was most common claim accounting to 34 models (51%). This article provide insight into the current status of evident online sales of ENDS in India. There is urgent need to implement regulations on online sales of these products and protect the future from such approaches of tobacco control which still have divided opinions. The study permits the use of web search engine to explore market availability of ENDS at various online retail websites. Recommendations from the study can be used to guide policy makers in developing strategies tailored to regulate availability and online sales of ENDS in India. © The Author 2017. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  12. Prediction Model and Principle of End-of-Life Threshold for Lithium Ion Batteries Based on Open Circuit Voltage Drifts

    International Nuclear Information System (INIS)

    Cui, Yingzhi; Yang, Jie; Du, Chunyu; Zuo, Pengjian; Gao, Yunzhi; Cheng, Xinqun; Ma, Yulin; Yin, Geping

    2017-01-01

    Highlights: •Open circuit voltage evolution over ageing of lithium ion batteries is deciphered. •The mechanism responsible for the end-of-life (EOL) threshold is elaborated. •A new prediction model of EOL threshold with improved accuracy is developed. •This EOL prediction model is promising for the applications in electric vehicles. -- Abstract: The end-of-life (EOL) of a lithium ion battery (LIB) is defined as the time point when the LIB can no longer provide sufficient power or energy to accomplish its intended function. Generally, the EOL occurs abruptly when the degradation of a LIB reaches the threshold. Therefore, current prediction methods of EOL by extrapolating the early degradation behavior often result in significant errors. To address this problem, this paper analyzes the reason for the EOL threshold of a LIB with shallow depth of discharge. It is found that the sudden appearance of EOL threshold results from the drift of open circuit voltage (OCV) at the end of both shallow depth and full discharges. Further, a new EOL threshold prediction model with highly improved accuracy is developed based on the OCV drifts and their evolution mechanism, which can effectively avoid the misjudgment of EOL threshold. The accuracy of this EOL threshold prediction model is verified by comparing with experimental results. The EOL threshold prediction model can be applied to other battery chemistry systems and its possible application in electric vehicles is finally discussed.

  13. T-section glulam timber bridge modules : modeling and performance

    Science.gov (United States)

    Paul A. Morgan; Steven E. Taylor; Michael A. Ritter; John M. Franklin

    1999-01-01

    This paper describes the design, modeling, and testing of two portable timber bridges, each consisting of two noninterconnected longitudinal glued-laminated timber (glulam) deck panels 1.8 m (6 ft) wide. One bridge is 12.2 m (40 ft) long while the other bridge is 10.7 m (35 ft) long. The deck panels are fabricated in a unique double-tee cross section. The bridges...

  14. 17 CFR 274.11a-1 - Form N-2, registration statement of closed end management investment companies.

    Science.gov (United States)

    2010-04-01

    ... statement of closed end management investment companies. 274.11a-1 Section 274.11a-1 Commodity and... management investment companies. This form shall be used as the registration statement to be filed pursuant to section 8(b) of the Investment Company Act of 1940 by closed end management investment companies...

  15. 14 CFR Section 3 - Chart of Balance Sheet Accounts

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Chart of Balance Sheet Accounts Section 3 Section 3 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION... Balance Sheet Classifications Section 3 Chart of Balance Sheet Accounts [See footnotes at end of table...

  16. Multiphysical model of heterogenous flow moving along а channel of variable cross-section

    Directory of Open Access Journals (Sweden)

    М. А. Васильева

    2017-10-01

    Full Text Available The article deals with the problem aimed at solving the fundamental problems of developing effective methods and tools for designing, controlling and managing the stream of fluid flowing in variable-section pipelines intended for the production of pumping equipment, medical devices and used in such areas of industry as mining, chemical, food production, etc. Execution of simulation modelling of flow motion according to the scheme of twisted paddle static mixer allows to estimate the efficiency of mixing by calculating the trajectory and velocities of the suspended particles going through the mixer, and also to estimate the pressure drop on the hydraulic flow resistance. The model examines the mixing of solids dissolved in a liquid at room temperature. To visualize the process of distributing the mixture particles over the cross-section and analyzing the mixing efficiency, the Poincaréplot module of the COMSOL Multiphysics software environment was used. For the first time, a multi-physical stream of heterogeneous flow model has been developed that describes in detail the physical state of the fluid at all points of the considered section at the initial time, takes into account the design parameters of the channel (orientation, dimensions, material, etc., specifies the laws of variation of the parameters at the boundaries of the calculated section in conditions of the wave change in the internal section of the working chamber-channel of the inductive peristaltic pumping unit under the influence of the energy of the magnetic field.

  17. Total cross sections of hadron interactions at high energies in low constituents number model

    International Nuclear Information System (INIS)

    Abramovskij, V.A.; Radchenko, N.V.

    2009-01-01

    We consider QCD hadrons interaction model in which gluons density is low in initial state wave function in rapidity space and real hadrons are produced from color strings decay. In this model behavior of total cross sections of pp, pp bar, π ± p, K ± p, γp, and γγ interactions is well described. The value of proton-proton total cross section at LHC energy is predicted

  18. The validity of the means-end chain model of consumer behaviour

    DEFF Research Database (Denmark)

    Scholderer, Joachim; Grunert, Klaus G.

    2004-01-01

    Despite its popularity in consumer research, means-end chain theory suffers from problems of unconfirmed validity: the nomological status of its central construct, the means-end chain, is still unknown. The aim of the research reported here was threefold: (a) to reformulate means-end chain theory....... In a pilot session, each participant completed four different laddering tasks. Each task consisted of four different consumer products varying on three different attributes. After the pilot session, the word material that participants had generated in the laddering task was entered into a database...

  19. Experimental evaluation of end-to-end delay in switched Ethernet application in the automotive domain

    OpenAIRE

    Beretis , Kostas; Symeonidis , Ieroklis

    2013-01-01

    International audience; This article presents an approach for deriving upper bound for end-to-end delay in a double star switched Ethernet network. Four traffic classes, following a strict priority queuing policy, were considered. The theoretical analysis was based on network calculus. An experimental setup, which accu-rately reflects an automotive communication network, was implemented in or-der to evaluate the theoretical model. The results obtained by the experiments provided valuable feed...

  20. End-Tidal CO2-Guided Chest Compression Delivery Improves Survival in a Neonatal Asphyxial Cardiac Arrest Model.

    Science.gov (United States)

    Hamrick, Justin T; Hamrick, Jennifer L; Bhalala, Utpal; Armstrong, Jillian S; Lee, Jeong-Hoo; Kulikowicz, Ewa; Lee, Jennifer K; Kudchadkar, Sapna R; Koehler, Raymond C; Hunt, Elizabeth A; Shaffner, Donald H

    2017-11-01

    To determine whether end-tidal CO2-guided chest compression delivery improves survival over standard cardiopulmonary resuscitation after prolonged asphyxial arrest. Preclinical randomized controlled study. University animal research laboratory. 1-2-week-old swine. After undergoing a 20-minute asphyxial arrest, animals received either standard or end-tidal CO2-guided cardiopulmonary resuscitation. In the standard group, chest compression delivery was optimized by video and verbal feedback to maintain the rate, depth, and release within published guidelines. In the end-tidal CO2-guided group, chest compression rate and depth were adjusted to obtain a maximal end-tidal CO2 level without other feedback. Cardiopulmonary resuscitation included 10 minutes of basic life support followed by advanced life support for 10 minutes or until return of spontaneous circulation. Mean end-tidal CO2 at 10 minutes of cardiopulmonary resuscitation was 34 ± 8 torr in the end-tidal CO2 group (n = 14) and 19 ± 9 torr in the standard group (n = 14; p = 0.0001). The return of spontaneous circulation rate was 7 of 14 (50%) in the end-tidal CO2 group and 2 of 14 (14%) in the standard group (p = 0.04). The chest compression rate averaged 143 ± 10/min in the end-tidal CO2 group and 102 ± 2/min in the standard group (p tidal CO2-guided chest compression delivery. The response of the relaxation arterial pressure and cerebral perfusion pressure to the initial epinephrine administration was greater in the end-tidal CO2 group than in the standard group (p = 0.01 and p = 0.03, respectively). The prevalence of resuscitation-related injuries was similar between groups. End-tidal CO2-guided chest compression delivery is an effective resuscitation method that improves early survival after prolonged asphyxial arrest in this neonatal piglet model. Optimizing end-tidal CO2 levels during cardiopulmonary resuscitation required that chest compression delivery rate exceed current guidelines

  1. Effects of positive end-expiratory pressure and recruitment maneuvers in a ventilator-induced injury mouse model.

    Directory of Open Access Journals (Sweden)

    Laura A Cagle

    Full Text Available Positive-pressure mechanical ventilation is an essential therapeutic intervention, yet it causes the clinical syndrome known as ventilator-induced lung injury. Various lung protective mechanical ventilation strategies have attempted to reduce or prevent ventilator-induced lung injury but few modalities have proven effective. A model that isolates the contribution of mechanical ventilation on the development of acute lung injury is needed to better understand biologic mechanisms that lead to ventilator-induced lung injury.To evaluate the effects of positive end-expiratory pressure and recruitment maneuvers in reducing lung injury in a ventilator-induced lung injury murine model in short- and longer-term ventilation.5-12 week-old female BALB/c mice (n = 85 were anesthetized, placed on mechanical ventilation for either 2 hrs or 4 hrs with either low tidal volume (8 ml/kg or high tidal volume (15 ml/kg with or without positive end-expiratory pressure and recruitment maneuvers.Alteration of the alveolar-capillary barrier was noted at 2 hrs of high tidal volume ventilation. Standardized histology scores, influx of bronchoalveolar lavage albumin, proinflammatory cytokines, and absolute neutrophils were significantly higher in the high-tidal volume ventilation group at 4 hours of ventilation. Application of positive end-expiratory pressure resulted in significantly decreased standardized histology scores and bronchoalveolar absolute neutrophil counts at low- and high-tidal volume ventilation, respectively. Recruitment maneuvers were essential to maintain pulmonary compliance at both 2 and 4 hrs of ventilation.Signs of ventilator-induced lung injury are evident soon after high tidal volume ventilation (as early as 2 hours and lung injury worsens with longer-term ventilation (4 hrs. Application of positive end-expiratory pressure and recruitment maneuvers are protective against worsening VILI across all time points. Dynamic compliance can be used guide

  2. Effects of positive end-expiratory pressure and recruitment maneuvers in a ventilator-induced injury mouse model

    Science.gov (United States)

    Franzi, Lisa M.; Linderholm, Angela L.; Last, Jerold A.; Adams, Jason Y.; Harper, Richart W.

    2017-01-01

    Background Positive-pressure mechanical ventilation is an essential therapeutic intervention, yet it causes the clinical syndrome known as ventilator-induced lung injury. Various lung protective mechanical ventilation strategies have attempted to reduce or prevent ventilator-induced lung injury but few modalities have proven effective. A model that isolates the contribution of mechanical ventilation on the development of acute lung injury is needed to better understand biologic mechanisms that lead to ventilator-induced lung injury. Objectives To evaluate the effects of positive end-expiratory pressure and recruitment maneuvers in reducing lung injury in a ventilator-induced lung injury murine model in short- and longer-term ventilation. Methods 5–12 week-old female BALB/c mice (n = 85) were anesthetized, placed on mechanical ventilation for either 2 hrs or 4 hrs with either low tidal volume (8 ml/kg) or high tidal volume (15 ml/kg) with or without positive end-expiratory pressure and recruitment maneuvers. Results Alteration of the alveolar-capillary barrier was noted at 2 hrs of high tidal volume ventilation. Standardized histology scores, influx of bronchoalveolar lavage albumin, proinflammatory cytokines, and absolute neutrophils were significantly higher in the high-tidal volume ventilation group at 4 hours of ventilation. Application of positive end-expiratory pressure resulted in significantly decreased standardized histology scores and bronchoalveolar absolute neutrophil counts at low- and high-tidal volume ventilation, respectively. Recruitment maneuvers were essential to maintain pulmonary compliance at both 2 and 4 hrs of ventilation. Conclusions Signs of ventilator-induced lung injury are evident soon after high tidal volume ventilation (as early as 2 hours) and lung injury worsens with longer-term ventilation (4 hrs). Application of positive end-expiratory pressure and recruitment maneuvers are protective against worsening VILI across all time points

  3. Effects of positive end-expiratory pressure and recruitment maneuvers in a ventilator-induced injury mouse model.

    Science.gov (United States)

    Cagle, Laura A; Franzi, Lisa M; Linderholm, Angela L; Last, Jerold A; Adams, Jason Y; Harper, Richart W; Kenyon, Nicholas J

    2017-01-01

    Positive-pressure mechanical ventilation is an essential therapeutic intervention, yet it causes the clinical syndrome known as ventilator-induced lung injury. Various lung protective mechanical ventilation strategies have attempted to reduce or prevent ventilator-induced lung injury but few modalities have proven effective. A model that isolates the contribution of mechanical ventilation on the development of acute lung injury is needed to better understand biologic mechanisms that lead to ventilator-induced lung injury. To evaluate the effects of positive end-expiratory pressure and recruitment maneuvers in reducing lung injury in a ventilator-induced lung injury murine model in short- and longer-term ventilation. 5-12 week-old female BALB/c mice (n = 85) were anesthetized, placed on mechanical ventilation for either 2 hrs or 4 hrs with either low tidal volume (8 ml/kg) or high tidal volume (15 ml/kg) with or without positive end-expiratory pressure and recruitment maneuvers. Alteration of the alveolar-capillary barrier was noted at 2 hrs of high tidal volume ventilation. Standardized histology scores, influx of bronchoalveolar lavage albumin, proinflammatory cytokines, and absolute neutrophils were significantly higher in the high-tidal volume ventilation group at 4 hours of ventilation. Application of positive end-expiratory pressure resulted in significantly decreased standardized histology scores and bronchoalveolar absolute neutrophil counts at low- and high-tidal volume ventilation, respectively. Recruitment maneuvers were essential to maintain pulmonary compliance at both 2 and 4 hrs of ventilation. Signs of ventilator-induced lung injury are evident soon after high tidal volume ventilation (as early as 2 hours) and lung injury worsens with longer-term ventilation (4 hrs). Application of positive end-expiratory pressure and recruitment maneuvers are protective against worsening VILI across all time points. Dynamic compliance can be used guide the frequency

  4. Manufacture of the straight section chambers for the SPring-8 storage ring

    International Nuclear Information System (INIS)

    Watanabe, K.; Saeki, H.; Sakaue, H.; Ohkuma, H.; Be, S.H.; Oishi, M.; Tuchiya, M.; Nishidono, T.

    1995-01-01

    To carry out the performance test of the vacuum system, we manufactured three different straight section chambers prior to the manufacture of the 48 cell full scale vacuum systems. One of three straight section chambers contains only downstream end absorber, while the other two contain a downstream end absorber, upstream end bellows and a photon beam extraction duct. In this paper, the manufacture of these chambers and their assemblies are described in detail. (author). 1 ref., 3 figs., 3 tabs

  5. Neutron Elastic Scattering Cross Sections Experimental Data and Optical Model Cross Section Calculations. A Compilation of Neutron Data from the Studsvik Neutron Physics Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Holmqvist, B; Wiedling, T

    1969-06-15

    Neutron elastic scattering cross section measurements have been going on for a long period at the Studsvik Van de Graaff laboratory. The cross sections of a range of elements have been investigated in the energy interval 1.5 to 8 MeV. The experimental data have been compared with cross sections calculated with the optical model when using a local nuclear potential.

  6. Challenging fission cross section simulation with long standing macro-microscopic model of nucleus potential energy surface

    International Nuclear Information System (INIS)

    Tamagno, Pierre

    2015-01-01

    The work presented here aims to improve models used in the fission cross section evaluation. The results give insights for a significant breakthrough in this field and yielded large extensions of the evaluation code CONRAD. Partial cross sections are inherently strongly correlated together as of the competition of the related reactions must yield the total cross section. Therefore improving fission cross section benefits to all partial cross sections. A sound framework for the simulation of competitive reactions had to be settled in order to further investigate on the fission reaction; this was implemented using the TALYS reference code as guideline. After ensuring consistency and consistency of the framework, focus was made on fission. Perspective resulting from the use of macroscopic-microscopic models such as the FRDM and FRLDM were analyzed; these models have been implemented and validated on experimental data and benchmarks. To comply with evaluation requirements in terms of computation time, several specific numerical methods have been used and parts of the program were written to run on GPU. These macroscopic-microscopic models yield potential energy surfaces that can be used to extract a one-dimensional fission barrier. This latter can then be used to obtained fission transmission coefficients that can be used in a Hauser-Feshbach model. This method has been finally tested for the calculation of the average fission cross section for 239 Pu(n,f). (author) [fr

  7. The Total Cross Section at the LHC: Models and Experimental Consequences

    CERN Document Server

    Cudell, J R

    2010-01-01

    I review the predictions of the total cross section for many models, and point out that some of them lead to the conclusion that the standard experimental analysis may lead to systematic errors much larger than expected.

  8. Simple kinetic theory model of reactive collisions. IV. Laboratory fixed orientational cross sections

    International Nuclear Information System (INIS)

    Evans, G.T.

    1987-01-01

    The differential orientational cross section, obtainable from molecular beam experiments on aligned molecules, is calculated using the line-of-normals model for reactive collisions involving hard convex bodies. By means of kinetic theory methods, the dependence of the cross section on the angle of attack γ 0 is expressed in a Legendre function expansion. Each of the Legendre expansion coefficients is given by an integral over the molecule-fixed cross section and functions of the orientation dependent threshold energy

  9. Analysis of the relationship between end-to-end distance and activity of single-chain antibody against colorectal carcinoma.

    Science.gov (United States)

    Zhang, Jianhua; Liu, Shanhong; Shang, Zhigang; Shi, Li; Yun, Jun

    2012-08-22

    We investigated the relationship of End-to-end distance between VH and VL with different peptide linkers and the activity of single-chain antibodies by computer-aided simulation. First, we developed (G4S)n (where n = 1-9) as the linker to connect VH and VL, and estimated the 3D structure of single-chain Fv antibody (scFv) by homologous modeling. After molecular models were evaluated and optimized, the coordinate system of every protein was built and unified into one coordinate system, and End-to-end distances calculated using 3D space coordinates. After expression and purification of scFv-n with (G4S)n as n = 1, 3, 5, 7 or 9, the immunoreactivity of purified ND-1 scFv-n was determined by ELISA. A multi-factorial relationship model was employed to analyze the structural factors affecting scFv: rn=ABn-ABO2+CDn-CDO2+BCn-BCst2. The relationship between immunoreactivity and r-values revealed that fusion protein structure approached the desired state when the r-value = 3. The immunoreactivity declined as the r-value increased, but when the r-value exceeded a certain threshold, it stabilized. We used a linear relationship to analyze structural factors affecting scFv immunoreactivity.

  10. Determination of tire cross-sectional geometric characteristics from a digitally scanned image

    Science.gov (United States)

    Danielson, Kent T.

    1995-08-01

    A semi-automated procedure is described for the accurate determination of geometrical characteristics using a scanned image of the tire cross-section. The procedure can be useful for cases when CAD drawings are not available or when a description of the actual cured tire is desired. Curves representing the perimeter of the tire cross-section are determined by an edge tracing scheme, and the plyline and cord-end positions are determined by locations of color intensities. The procedure provides an accurate description of the perimeter of the tire cross-section and the locations of plylines and cord-ends. The position, normals, and curvatures of the cross-sectional surface are included in this description. The locations of the plylines provide the necessary information for determining the ply thicknesses and relative position to a reference surface. Finally, the locations of the cord-ends provide a means to calculate the cord-ends per inch (epi). Menu driven software has been developed to facilitate the procedure using the commercial code, PV-Wave by Visual Numerics, Inc., to display the images. From a single user interface, separate modules are executed for image enhancement, curve fitting the edge trace of the cross-sectional perimeter, and determining the plyline and cord-end locations. The code can run on SUN or SGI workstations and requires the use of a mouse to specify options or identify items on the scanned image.

  11. Inelastic cross-sections for electron transport in liquid water: a comparison of dielectric models

    International Nuclear Information System (INIS)

    Emfietzoglou, D.

    2003-01-01

    Various methodologies for constructing inelastic cross-sections for low-energy (<10 keV) electron transport in liquid water are presented and compared. They are all based on an optical-data model which provides the dependence on energy loss, and a dispersion algorithm which incorporates the momentum-transfer dependence. A Drude dielectric model was used to analytically represent the optical data. Various dispersion schemes were examined: the Bethe approximation, the δ-oscillator models of Ashley and Liljequist, and two forms of Ritchie's extended-Drude model. They all have been used in Monte-Carlo (MC) codes for analog electron transport in the condensed phase. Results in the form of differential and total inelastic cross-sections are presented. Where possible, comparisons with results of other studies are made. It was found that, despite the application of general constraints (e.g. sum rules), the optical model has a notable influence on the single-collision energy loss spectrum. In addition, both the shape and peak position of the total and differential cross-section distributions depend strongly on the dispersion model adopted. The work is particularly relevant to the development of event-by-event MC transport codes for liquid water, as well as, to the calculations of stopping-powers below the range of applicability of Bethe's formula

  12. The Non-universality of the Low-mass End of the IMF is Robust against the Choice of SSP Model

    NARCIS (Netherlands)

    Spiniello, C.; Trager, S. C.; Koopmans, L. V. E.

    We perform a direct comparison of two state-of-the art single stellar population (SSP) models that have been used to demonstrate the non-universality of the low-mass end of the initial mass function (IMF) slope. The two public versions of the SSP models are restricted to either solar abundance

  13. Kinetics of end-to-end collision in short single-stranded nucleic acids.

    Science.gov (United States)

    Wang, Xiaojuan; Nau, Werner M

    2004-01-28

    A novel fluorescence-based method, which entails contact quenching of the long-lived fluorescent state of 2,3-diazabicyclo[2.2.2]-oct-2-ene (DBO), was employed to measure the kinetics of end-to-end collision in short single-stranded oligodeoxyribonucleotides of the type 5'-DBO-(X)n-dG with X = dA, dC, dT, or dU and n = 2 or 4. The fluorophore was covalently attached to the 5' end and dG was introduced as an efficient intrinsic quencher at the 3' terminus. The end-to-end collision rates, which can be directly related to the efficiency of intramolecular fluorescence quenching, ranged from 0.1 to 9.0 x 10(6) s(-1). They were strongly dependent on the strand length, the base sequence, as well as the temperature. Oligonucleotides containing dA in the backbone displayed much slower collision rates and significantly higher positive activation energies than strands composed of pyrimidine bases, suggesting a higher intrinsic rigidity of oligoadenylate. Comparison of the measured collision rates in short single-stranded oligodeoxyribonucleotides with the previously reported kinetics of hairpin formation indicates that the intramolecular collision is significantly faster than the nucleation step of hairpin closing. This is consistent with the configurational diffusion model suggested by Ansari et al. (Ansari, A.; Kuznetsov, S. V.; Shen, Y. Proc.Natl. Acad. Sci. USA 2001, 98, 7771-7776), in which the formation of misfolded loops is thought to slow hairpin formation.

  14. A Conceptual Model for Increasing Use of Electronic Medical Records by Primary Care Physicians Through End-User Support.

    Science.gov (United States)

    Randhawa, Gurprit K

    2017-01-01

    A conceptual model for exploring the relationship between end-user support (EUS) and electronic medical record (EMR) use by primary care physicians is presented. The model was developed following a review of conceptual and theoretical frameworks related to technology adoption/use and EUS. The model includes (a) one core construct (facilitating conditions), (b) four antecedents and one postcedent of facilitating conditions, and (c) four moderators. EMR use behaviour is the key outcome of the model. The proposed conceptual model should be tested. The model may be used to inform planning and decision-making for EMR implementations to increase EMR use for benefits realization.

  15. HVAC system optimisation-in-building section

    Energy Technology Data Exchange (ETDEWEB)

    Lu, L.; Cai, W.; Xie, L.; Li, S.; Soh, Y.C. [School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore (Singapore)

    2004-07-01

    This paper presents a practical method to optimise in-building section of centralised Heating, Ventilation and Air-Conditioning (HVAC) systems which consist of indoor air loops and chilled water loops. First, through component characteristic analysis, mathematical models associated with cooling loads and energy consumption for heat exchangers and energy consuming devices are established. By considering variation of cooling load of each end user, adaptive neuro-fuzzy inference system (ANFIS) is employed to model duct and pipe networks and obtain optimal differential pressure (DP) set points based on limited sensor information. A mix-integer nonlinear constraint optimization of system energy is formulated and solved by a modified genetic algorithm. The main feature of our paper is a systematic approach in optimizing the overall system energy consumption rather than that of individual component. A simulation study for a typical centralized HVAC system is provided to compare the proposed optimisation method with traditional ones. The results show that the proposed method indeed improves the system performance significantly. (author)

  16. HVAC system optimization - in-building section

    Energy Technology Data Exchange (ETDEWEB)

    Lu Lu; Wenjian Cai; Lihua Xie; Shujiang Li; Yeng Chai Soh [Nanyang Technological Univ., Singapore (Singapore). School of Electrical and Electronic Engineering

    2005-01-01

    This paper presents a practical method to optimize in-building section of centralized Heating, Ventilation and Air-conditioning (HVAC) systems which consist of indoor air loops and chilled water loops. First, through component characteristic analysis, mathematical models associated with cooling loads and energy consumption for heat exchangers and energy consuming devices are established. By considering variation of cooling load of each end user, adaptive neuro-fuzzy inference system (ANFIS) is employed to model duct and pipe networks and obtain optimal differential pressure (DP) set points based on limited sensor information. A mix-integer nonlinear constraint optimization of system energy is formulated and solved by a modified genetic algorithm. The main feature of our paper is a systematic approach in optimizing the overall system energy consumption rather than that of individual component. A simulation study for a typical centralized HVAC system is provided to compare the proposed optimization method with traditional ones. The results show that the proposed method indeed improves the system performance significantly. (author)

  17. Integration of the End Cap TEC+ of the CMS Silicon Strip Tracker

    CERN Document Server

    Adler, Volker; Ageron, Michel; Agram, Jean-Laurent; Atz, Bernd; Barvich, Tobias; Baulieu, Guillaume; Beaumont, Willem; Beissel, Franz; Bergauer, Thomas; Berst, Jean-Daniel; Blüm, Peter; Bock, E; Bogelsbacher, F; de Boer, Wim; Bonnet, Jean-Luc; Bonnevaux, Alain; Boudoul, Gaelle; Bouhali, Othmane; Braunschweig, Wolfgang; Bremer, R; Brom, Jean-Marie; Butz, Erik; Chabanat, Eric; Chabert, Eric Christian; Clerbaux, Barbara; Contardo, Didier; De Callatay, Bernard; Dehm, Philip; Delaere, Christophe; Della Negra, Rodolphe; Dewulf, Jean-Paul; D'Hondt, Jorgen; Didierjean, Francois; Dierlamm, Alexander; Dirkes, Guido; Dragicevic, Marko; Drouhin, Frédéric; Ernenwein, Jean-Pierre; Esser, Hans; Estre, Nicolas; Fahrer, Manuel; Feld, Lutz; Fernández, J; Florins, Benoit; Flossdorf, Alexander; Flucke, Gero; Flügge, Günter; Fontaine, Jean-Charles; Freudenreich, Klaus; Frey, Martin; Friedl, Markus; Furgeri, Alexander; Giraud, Noël; Goerlach, Ulrich; Goorens, Robert; Graehling, Philippe; Grégoire, Ghislain; Gregoriev, E; Gross, Laurent; Hansel, S; Haroutunian, Roger; Hartmann, Frank; Heier, Stefan; Hermanns, Thomas; Heydhausen, Dirk; Heyninck, Jan; Hosselet, J; Hrubec, Josef; Jahn, Dieter; Juillot, Pierre; Kaminski, Jochen; Karpinski, Waclaw; Kaussen, Gordon; Keutgen, Thomas; Klanner, Robert; Klein, Katja; König, Stefan; Kosbow, M; Krammer, Manfred; Ledermann, Bernhard; Lemaître, Vincent; De Lentdecker, Gilles; Linn, Alexander; Lounis, Abdenour; Lübelsmeyer, Klaus; Lumb, Nicholas; Maazouzi, Chaker; Mahmoud, Tariq; Michotte, Daniel; Militaru, Otilia; Mirabito, Laurent; Müller, Thomas; Neukermans, Lionel; Ollivetto, C; Olzem, Jan; Ostapchuk, Andrey; Pandoulas, Demetrios; Pein, Uwe; Pernicka, Manfred; Perriès, Stephane; Piaseki, C; Pierschel, Gerhard; Piotrzkowski, Krzysztof; Poettgens, Michael; Pooth, Oliver; Rouby, Xavier; Sabellek, Andreas; Schael, Stefan; Schirm, Norbert; Schleper, Peter; Schmitz, Stefan Antonius; Schultz von Dratzig, Arndt; Siedling, Rolf; Simonis, Hans-Jürgen; Stahl, Achim; Steck, Pia; Steinbruck, G; Stoye, Markus; Strub, Roger; Tavernier, Stefaan; Teyssier, Daniel; Theel, Andreas; Trocmé, Benjamin; Udo, Fred; Van der Donckt, M; Van der Velde, C; Van Hove, Pierre; Vanlaer, Pascal; Van Lancker, Luc; Van Staa, Rolf; Vanzetto, Sylvain; Weber, Markus; Weiler, Thomas; Weseler, Siegfried; Wickens, John; Wittmer, Bruno; Wlochal, Michael; De Wolf, Eddi A; Zhukov, Valery; Zoeller, Marc Henning

    2009-01-01

    The silicon strip tracker of the CMS experiment has been completed and inserted into the CMS detector in late 2007. The largest sub-system of the tracker is its end cap system, comprising two large end caps (TEC) each containing 3200 silicon strip modules. To ease construction, the end caps feature a modular design: groups of about 20 silicon modules are placed on sub-assemblies called petals and these self-contained elements are then mounted into the TEC support structures. Each end cap consists of 144 petals, and the insertion of these petals into the end cap structure is referred to as TEC integration. The two end caps were integrated independently in Aachen (TEC+) and at CERN (TEC--). This note deals with the integration of TEC+, describing procedures for end cap integration and for quality control during testing of integrated sections of the end cap and presenting results from the testing.

  18. On the model-dependence of the relation between minimum-bias and inelastic proton-proton cross sections

    International Nuclear Information System (INIS)

    Ostapchenko, S.

    2011-01-01

    The model-dependence of the relation between the inelastic and various minimum-bias proton-proton cross sections is analyzed, paying a special attention to the sensitivity of minimum-bias triggers to diffractive collisions. Concentrating on the trigger selections of the ATLAS experiment, the measured cross sections are compared to predictions of a number of hadronic Monte Carlo models used in the cosmic ray field. It is demonstrated that the ATLAS results are able to discriminate between different models and between certain theoretical approaches for soft multi-particle production. On the other hand, the strong model-dependence of the selection efficiency of the minimum-bias triggers prevents one from inferring high mass diffraction rate from the discussed data. Moreover, the measured cross sections prove to be insensitive to the production of low mass diffractive states in proton-proton collisions. Consequently, a reliable determination of the total inelastic cross section requires forward proton tracking by a dedicated experiment.

  19. Program POD; A computer code to calculate nuclear elastic scattering cross sections with the optical model and neutron inelastic scattering cross sections by the distorted-wave born approximation

    International Nuclear Information System (INIS)

    Ichihara, Akira; Kunieda, Satoshi; Chiba, Satoshi; Iwamoto, Osamu; Shibata, Keiichi; Nakagawa, Tsuneo; Fukahori, Tokio; Katakura, Jun-ichi

    2005-07-01

    The computer code, POD, was developed to calculate angle-differential cross sections and analyzing powers for shape-elastic scattering for collisions of neutron or light ions with target nucleus. The cross sections are computed with the optical model. Angle-differential cross sections for neutron inelastic scattering can also be calculated with the distorted-wave Born approximation. The optical model potential parameters are the most essential inputs for those model computations. In this program, the cross sections and analyzing powers are obtained by using the existing local or global parameters. The parameters can also be inputted by users. In this report, the theoretical formulas, the computational methods, and the input parameters are explained. The sample inputs and outputs are also presented. (author)

  20. 15 CFR 745.2 - End-Use Certificate reporting requirements under the Chemical Weapons Convention.

    Science.gov (United States)

    2010-01-01

    ... requirements under the Chemical Weapons Convention. 745.2 Section 745.2 Commerce and Foreign Trade Regulations... EXPORT ADMINISTRATION REGULATIONS CHEMICAL WEAPONS CONVENTION REQUIREMENTS § 745.2 End-Use Certificate reporting requirements under the Chemical Weapons Convention. Note: The End-Use Certificate requirement of...

  1. THREE PERSPECTIVES ON MANAGING FRONT END INNOVATION

    DEFF Research Database (Denmark)

    Jensen, Anna Rose Vagn; Clausen, Christian; Gish, Liv

    2018-01-01

    as a complementary perspective. The paper combines a literature review with an empirical examination of the application of these multiple perspectives across three cases of front end of innovation (FEI) management in mature product developing companies. While the process models represent the dominant, albeit rather...... to represent an emergent approach in managing FEI where process models, knowledge strategies and objects become integrated elements in more advanced navigational strategies for key players.......This paper presents three complementary perspectives on the management of front end innovation: A process model perspective, a knowledge perspective and a translational perspective. While the first two perspectives are well established in literature, we offer the translation perspective...

  2. Modelling of N21P emission rates in aurora using various cross sections for excitation

    Directory of Open Access Journals (Sweden)

    O. Jokiaho

    2009-06-01

    Full Text Available Measurements of N21P auroral emissions from the (4,1 and (5,2 bands have been made at high temporal and spatial resolution in the region of the magnetic zenith. The instrument used was the auroral imager ASK, situated at Ramfjordmoen, Norway (69.6 N, 19.2 E on 22 October 2006. Measurements from the European Incoherent Scatter Radar (EISCAT have been combined with the optical measurements, and incorporated into an ionospheric model to obtain height profiles of electron density and emission rates of the N21P bands. The radar data provide essential verification that the energy flux used in the model is correct. One of the most important inputs to the model is the cross section for excitation to the B3Πg electronic state, as well as the cross sections to higher states from which cascading into the B state occurs. The balance equations for production and loss of the populations of all levels in each state are solved in order to find the cascade contributions. Several sets of cross sections have been considered, and selected cross sections have been used to construct "emission" cross sections for the observed bands. The resulting brightnesses are compared with those measured by ASK. The importance of specific contributions from cascading is found, with more than 50% of the total brightness resulting from cascading. The cross sections used are found to produce a range of brightnesses well within the uncertainty of both the modelled and measured values.

  3. REASONING IN THE FUZZY FRONT END OF INNOVATION:

    DEFF Research Database (Denmark)

    Haase, Louise Møller; Laursen, Linda Nhu

    2018-01-01

    in the fuzzy front end is the reasoning process: innovation teams are faced with open-ended, ill-defined problems, where they need to make decisions about an unknown future but have only incomplete, ambiguous and contradicting insights available. We study the reasoning of experts, how they frame to make sense...... of all the insights and create a basis for decision-making in relation to a new project. Based on case studies of five innovative products from various industries, we propose a Product DNA model for understanding the reasoning in the fuzzy front end of innovation. The Product DNA Model explains how...... experts reason and what direct their reasoning....

  4. TOWARD END-TO-END MODELING FOR NUCLEAR EXPLOSION MONITORING: SIMULATION OF UNDERGROUND NUCLEAR EXPLOSIONS AND EARTHQUAKES USING HYDRODYNAMIC AND ANELASTIC SIMULATIONS, HIGH-PERFORMANCE COMPUTING AND THREE-DIMENSIONAL EARTH MODELS

    Energy Technology Data Exchange (ETDEWEB)

    Rodgers, A; Vorobiev, O; Petersson, A; Sjogreen, B

    2009-07-06

    This paper describes new research being performed to improve understanding of seismic waves generated by underground nuclear explosions (UNE) by using full waveform simulation, high-performance computing and three-dimensional (3D) earth models. The goal of this effort is to develop an end-to-end modeling capability to cover the range of wave propagation required for nuclear explosion monitoring (NEM) from the buried nuclear device to the seismic sensor. The goal of this work is to improve understanding of the physical basis and prediction capabilities of seismic observables for NEM including source and path-propagation effects. We are pursuing research along three main thrusts. Firstly, we are modeling the non-linear hydrodynamic response of geologic materials to underground explosions in order to better understand how source emplacement conditions impact the seismic waves that emerge from the source region and are ultimately observed hundreds or thousands of kilometers away. Empirical evidence shows that the amplitudes and frequency content of seismic waves at all distances are strongly impacted by the physical properties of the source region (e.g. density, strength, porosity). To model the near-source shock-wave motions of an UNE, we use GEODYN, an Eulerian Godunov (finite volume) code incorporating thermodynamically consistent non-linear constitutive relations, including cavity formation, yielding, porous compaction, tensile failure, bulking and damage. In order to propagate motions to seismic distances we are developing a one-way coupling method to pass motions to WPP (a Cartesian anelastic finite difference code). Preliminary investigations of UNE's in canonical materials (granite, tuff and alluvium) confirm that emplacement conditions have a strong effect on seismic amplitudes and the generation of shear waves. Specifically, we find that motions from an explosion in high-strength, low-porosity granite have high compressional wave amplitudes and weak

  5. Development of a cross-section based stream package for MODFLOW

    Science.gov (United States)

    Ou, G.; Chen, X.; Irmak, A.

    2012-12-01

    Accurate simulation of stream-aquifer interactions for wide rivers using the streamflow routing package in MODFLOW is very challenging. To better represent a wide river spanning over multiple model grid cells, a Cross-Section based streamflow Routing (CSR) package is developed and incorporated into MODFLOW to simulate the interaction between streams and aquifers. In the CSR package, a stream segment is represented as a four-point polygon instead of a polyline which is traditionally used in streamflow routing simulation. Each stream segment is composed of upstream and downstream cross-sections. A cross-section consists of a number of streambed points possessing coordinates, streambed thicknesses and streambed hydraulic conductivities to describe the streambed geometry and hydraulic properties. The left and right end points are used to determine the locations of the stream segments. According to the cross-section geometry and hydraulic properties, CSR calculates the new stream stage at the cross-section using the Brent's method to solve the Manning's Equation. A module is developed to automatically compute the area of the stream segment polygon on each intersected MODFLOW grid cell as the upstream and downstream stages change. The stream stage and streambed hydraulic properties of model grids are interpolated based on the streambed points. Streambed leakage is computed as a function of streambed conductance and difference between the groundwater level and stream stage. The Muskingum-Cunge flow routing scheme with variable parameters is used to simulate the streamflow as the groundwater (discharge or recharge) contributes as lateral flows. An example is used to illustrate the capabilities of the CSR package. The result shows that the CSR is applicable to describing the spatial and temporal variation in the interaction between streams and aquifers. The input data become simple due to that the internal program automatically interpolates the cross-section data to each

  6. Reaction of oxygen with γ, δ-ethylenic phenylhydrazones. Model reaction of end-group behavior in phenylhydrazine-accelerated oxidation of natural rubber

    International Nuclear Information System (INIS)

    El Hamdaoui, A.; Reyx, D.; Campistron, I.

    1995-01-01

    An accurate definition of terminal groups of chains in the liquid polymers obtained by the phenylhydrazine-accelerated oxidation of natural rubber is needed. The object of the work was to use model molecules to explore the behavior of γ,δ-ethylenic methylketone phenylhydrazone end-groups in oxidation conditions. We have investigated the synthesis and characterization of models of these hypothetical end-groups, methylketones and phenones 1, their phenylhydrazones 2, the α-(phenyldiazenyl)hydroperoxides 3 resulting from reaction of 2 with oxygen, and the α-(phenyldiazenyl)alcohols 4 as characteristic derivatives of 3 or as models of possible reduced structures in oxidized liquid natural rubber. Three original syntheses of γ,δ-ethylenic ketones were carried out. In the case of γ,δ-ethylenic phenylhydrazones, the oxidation led to the expected α-(phenyldiazenyl)hydroperoxides and to epoxide derivatives of α-(phenyldiazenyl)alcohols 5 and ketones 6. An intramolecular mechanism is proposed. The results are used to predict the possibilities of identification of the corresponding end-groups in liquid rubbers produced in this way. (authors). 16 refs., 12 figs., 3 tabs

  7. Advanced Camera Image Cropping Approach for CNN-Based End-to-End Controls on Sustainable Computing

    Directory of Open Access Journals (Sweden)

    Yunsick Sung

    2018-03-01

    Full Text Available Recent research on deep learning has been applied to a diversity of fields. In particular, numerous studies have been conducted on self-driving vehicles using end-to-end approaches based on images captured by a single camera. End-to-end controls learn the output vectors of output devices directly from the input vectors of available input devices. In other words, an end-to-end approach learns not by analyzing the meaning of input vectors, but by extracting optimal output vectors based on input vectors. Generally, when end-to-end control is applied to self-driving vehicles, the steering wheel and pedals are controlled autonomously by learning from the images captured by a camera. However, high-resolution images captured from a car cannot be directly used as inputs to Convolutional Neural Networks (CNNs owing to memory limitations; the image size needs to be efficiently reduced. Therefore, it is necessary to extract features from captured images automatically and to generate input images by merging the parts of the images that contain the extracted features. This paper proposes a learning method for end-to-end control that generates input images for CNNs by extracting road parts from input images, identifying the edges of the extracted road parts, and merging the parts of the images that contain the detected edges. In addition, a CNN model for end-to-end control is introduced. Experiments involving the Open Racing Car Simulator (TORCS, a sustainable computing environment for cars, confirmed the effectiveness of the proposed method for self-driving by comparing the accumulated difference in the angle of the steering wheel in the images generated by it with those of resized images containing the entire captured area and cropped images containing only a part of the captured area. The results showed that the proposed method reduced the accumulated difference by 0.839% and 0.850% compared to those yielded by the resized images and cropped images

  8. Notes on modeling and simulation

    Energy Technology Data Exchange (ETDEWEB)

    Redondo, Antonio [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-10

    These notes present a high-level overview of how modeling and simulation are carried out by practitioners. The discussion is of a general nature; no specific techniques are examined but the activities associated with all modeling and simulation approaches are briefly addressed. There is also a discussion of validation and verification and, at the end, a section on why modeling and simulation are useful.

  9. A Vehicle Management End-to-End Testing and Analysis Platform for Validation of Mission and Fault Management Algorithms to Reduce Risk for NASA's Space Launch System

    Science.gov (United States)

    Trevino, Luis; Johnson, Stephen B.; Patterson, Jonathan; Teare, David

    2015-01-01

    The development of the Space Launch System (SLS) launch vehicle requires cross discipline teams with extensive knowledge of launch vehicle subsystems, information theory, and autonomous algorithms dealing with all operations from pre-launch through on orbit operations. The characteristics of these systems must be matched with the autonomous algorithm monitoring and mitigation capabilities for accurate control and response to abnormal conditions throughout all vehicle mission flight phases, including precipitating safing actions and crew aborts. This presents a large complex systems engineering challenge being addressed in part by focusing on the specific subsystems handling of off-nominal mission and fault tolerance. Using traditional model based system and software engineering design principles from the Unified Modeling Language (UML), the Mission and Fault Management (M&FM) algorithms are crafted and vetted in specialized Integrated Development Teams composed of multiple development disciplines. NASA also has formed an M&FM team for addressing fault management early in the development lifecycle. This team has developed a dedicated Vehicle Management End-to-End Testbed (VMET) that integrates specific M&FM algorithms, specialized nominal and off-nominal test cases, and vendor-supplied physics-based launch vehicle subsystem models. The flexibility of VMET enables thorough testing of the M&FM algorithms by providing configurable suites of both nominal and off-nominal test cases to validate the algorithms utilizing actual subsystem models. The intent is to validate the algorithms and substantiate them with performance baselines for each of the vehicle subsystems in an independent platform exterior to flight software test processes. In any software development process there is inherent risk in the interpretation and implementation of concepts into software through requirements and test processes. Risk reduction is addressed by working with other organizations such as S

  10. Novel model for end-neuroma formation in the amputated rabbit forelimb

    Directory of Open Access Journals (Sweden)

    Kuiken Todd A

    2010-03-01

    Full Text Available Abstract Background The forelimb amputee poses many reconstructive challenges in the clinical setting, and there is a paucity of established surgical models for study. To further elucidate the pathogenic process in amputation neuroma formation, we created a reproducible, well-tolerated rabbit forelimb amputation model. Methods Upon approval from the Institutional Animal Care and Use Committee, 5 New Zealand White rabbits underwent left forelimb amputation. During this initial surgery, the median, radial and ulnar nerves were transected 1.6-2.5 (mean 2.0 cm distal to the brachial plexus, transposed onto the anterior chest wall and preserved at length. Six weeks subsequent to the amputation, the distal 5 mm of each neuroma was excised, and the remaining stump underwent histomorphometric analysis. Results The nerve cross sectional areas increased by factors of 1.99, 3.17, and 2.59 in the median (p = 0.077, radial (p Conclusion Given that the surgical model appears well-tolerated by the rabbits and that patterns of morphologic change are consistent and reproducible, we are encouraged to further investigate the utility of this model in the pathogenesis of neuroma formation.

  11. Experimental study of prequalified status of flush end plate connections

    Directory of Open Access Journals (Sweden)

    Sherif H.M. Hassanien

    2016-04-01

    Full Text Available Seismic design of steel structures is an essential part of the design process. Egyptian loading code development process continues in a high rate to catch up with emerging new concepts and standards. Steel design codes (ASD and LRFD are not developing in the same speed, which prevents the full utilization and application of loading code. The above reason leads to the need for evaluating flush end plate connections from prequalification point of view according to international standards. Due to the lack of sufficient experimental data on flush end-plate connections, an experimental program was conducted to investigate this topic. Six flush end-plate samples were designed according to the Egyptian code for steel construction (ECP205 ASD using different beam and column sections, bolt diameters and grades. A cyclic loading pattern defined by international standards was used in the testing process, and the performance was evaluated accordingly. Evaluation of M–Φ curves showed that in some cases flush end plate connections satisfy the strict requirements for prequalification. However, beam sections having limited depth fail to achieve prequalification criteria for the connections. Reduced web may be used to enhance the connection status and is investigated in one of the samples to evaluate its impact on connection performance and the failure mode. The proposed staggered hole configuration showed a promising performance.

  12. Elective caesarean section versus vaginal delivery. Whither the end of traditional obstetrics?

    Science.gov (United States)

    Husslein, P

    2001-11-01

    No other topic has dominated the obstetrical discussion to the same extent as caesarean section. Nor has any other aspect of obstetrics been subject to a comparable degree of professional controversy,quite recently the topic has been discussed in this journal by Ludwig and Loeffler. For some caesarean section remains a major surgical procedure with a corresponding level of risk, which must only be employed in the presence of specific complications and in conjunction with a clearly defined set of indications; others consider caesarean section quite simply to be the most efficient and straightforward means to deliver as well as the one attended by the least amount of risk. Opinion among those most immediately affected is likewise divided: For many women the experience of vaginal birth is among the most fulfilling of their entire life - comparable only to sexuality-related moments of ecstasy - other women come to regard birth as the worst thing that ever happened to them an experience attended by pain, fear, loneliness, perhaps even long lasting negative consequences. There can be no doubt that, this question also affects the foundations of patriarchal thinking, still so firmly embedded in peoples' minds: Are doctors to determine what exactly takes place in the delivery room and in the operating theatre, or will the patient - in obstetrics, the parturient - be enabled to assert her right to self-determination also in the medical context; especially in light of the fact that said right can currently be exercised in an almost unlimited fashion throughout the rest of one's adult life? It is against the wider background of this ongoing controversy that the ensuing article will seek to defuse the emotional charge characterising some of the commonly employed arguments and instead revert to a more rational and factually based approach to this question.

  13. Fast-neutron total and scattering cross sections of sup 58 Ni and nuclear models

    Energy Technology Data Exchange (ETDEWEB)

    Smith, A.B.; Guenther, P.T.; Whalen, J.F. (Argonne National Lab., IL (United States)); Chiba, S. (Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment)

    1991-07-01

    The neutron total cross sections of {sup 58}Ni were measured from {approx} 1 to > 10 MeV using white-source techniques. Differential neutron elastic-scattering cross sections were measured from {approx} 4.5 to 10 MeV at {approx} 0.5 MeV intervals with {ge} 75 differential values per distribution. Differential neutron inelastic-scattering cross sections were measured, corresponding to fourteen levels with excitations up to 4.8 MeV. The measured results, combined with relevant values available in the literature, were interpreted in terms of optical-statistical and coupled-channels model using both vibrational and rotational coupling schemes. The physical implications of the experimental results nd their interpretation are discussed in the contexts of optical-statistical, dispersive-optical, and coupled-channels models. 61 refs.

  14. Probalistisk short-term risk modeling for back-end fuel cycle and waste management facilities

    International Nuclear Information System (INIS)

    Kjellbert, N.A.

    1980-03-01

    This study of probabilistic short-term risk modeling of back-end fuel cycle and waste management facilities represents the continuation of work started in 1977. The purpose of the report is to present a more detailed survey of models and analysis techniques that mey be applicable. The definition of the risk concept and the nature of the facilities and events which are to be analyzed are described. The most important criteria are that the model or method shall be quantitative, logically/scientifically based, and be able to handle systems of some complexity. Several formalized analysis methods are described, most of them emanating from reliability theory. No single model will fulfill all criteria simultaneously, to the degree desired. Nevertheless, fault tree analysis seems to be an efficient tool in many applications, although it must probably be used together with other models in most cases. Other methodologies described can also be useful, such as failure modes and effects analysis, renewal theory and Markov chains, reliability block diagrams, event trees and cause/consequence diagrams, the GO methodology, Monte Carlo simulation, and, often necessary, various consequence modeling techniques. (author)

  15. Preliminary assessment of Geant4 HP models and cross section libraries by reactor criticality benchmark calculations

    DEFF Research Database (Denmark)

    Cai, Xiao-Xiao; Llamas-Jansa, Isabel; Mullet, Steven

    2013-01-01

    Geant4 is an open source general purpose simulation toolkit for particle transportation in matter. Since the extension of the thermal scattering model in Geant4.9.5 and the availability of the IAEA HP model cross section libraries, it is now possible to extend the application area of Geant4......, U and O in uranium dioxide, Al metal, Be metal, and Fe metal. The native HP cross section library G4NDL does not include data for elements with atomic number larger than 92. Therefore, transuranic elements, which have impacts for a realistic reactor, can not be simulated by the combination of the HP...... models and the G4NDL library. However, cross sections of those missing isotopes were made available recently through the IAEA project “new evaluated neutron cross section libraries for Geant4”....

  16. 17 CFR 270.12b-1 - Distribution of shares by registered open-end management investment company.

    Science.gov (United States)

    2010-04-01

    ... registered open-end management investment company. 270.12b-1 Section 270.12b-1 Commodity and Securities... 1940 § 270.12b-1 Distribution of shares by registered open-end management investment company. (a)(1... the printing and mailing of sales literature; (b) A registered, open-end management investment company...

  17. Electron-Impact Excitation Cross Sections for Modeling Non-Equilibrium Gas

    Science.gov (United States)

    Huo, Winifred M.; Liu, Yen; Panesi, Marco; Munafo, Alessandro; Wray, Alan; Carbon, Duane F.

    2015-01-01

    In order to provide a database for modeling hypersonic entry in a partially ionized gas under non-equilibrium, the electron-impact excitation cross sections of atoms have been calculated using perturbation theory. The energy levels covered in the calculation are retrieved from the level list in the HyperRad code. The downstream flow-field is determined by solving a set of continuity equations for each component. The individual structure of each energy level is included. These equations are then complemented by the Euler system of equations. Finally, the radiation field is modeled by solving the radiative transfer equation.

  18. A macroscopic cross-section model for BWR pin-by-pin core analysis

    International Nuclear Information System (INIS)

    Fujita, Tatsuya; Endo, Tomohiro; Yamamoto, Akio

    2014-01-01

    A macroscopic cross-section model used in boiling water reactor (BWR) pin-by-pin core analysis is studied. In the pin-by-pin core calculation method, pin-cell averaged cross sections are calculated for many combinations of core state and depletion history variables and are tabulated prior to core calculations. Variations of cross sections in a core simulator are caused by two different phenomena (i.e. instantaneous and history effects). We treat them through the core state variables and the exposure-averaged core state variables, respectively. Furthermore, the cross-term effect among the core state and the depletion history variables is considered. In order to confirm the calculation accuracy and discuss the treatment of the cross-term effect, the k-infinity and the pin-by-pin fission rate distributions in a single fuel assembly geometry are compared. Some cross-term effects could be negligible since the impacts of them are sufficiently small. However, the cross-term effects among the control rod history (or the void history) and other variables have large impacts; thus, the consideration of them is crucial. The present macroscopic cross-section model, which considers such dominant cross-term effects, well reproduces the reference results and can be a candidate in practical applications for BWR pin-by-pin core analysis on the normal operations. (author)

  19. Defining the end-point of mastication: A conceptual model.

    Science.gov (United States)

    Gray-Stuart, Eli M; Jones, Jim R; Bronlund, John E

    2017-10-01

    The great risks of swallowing are choking and aspiration of food into the lungs. Both are rare in normal functioning humans, which is remarkable given the diversity of foods and the estimated 10 million swallows performed in a lifetime. Nevertheless, it remains a major challenge to define the food properties that are necessary to ensure a safe swallow. Here, the mouth is viewed as a well-controlled processor where mechanical sensory assessment occurs throughout the occlusion-circulation cycle of mastication. Swallowing is a subsequent action. It is proposed here that, during mastication, temporal maps of interfacial property data are generated, which the central nervous system compares against a series of criteria in order to be sure that the bolus is safe to swallow. To determine these criteria, an engineering hazard analysis tool, alongside an understanding of fluid and particle mechanics, is used to deduce the mechanisms by which food may deposit or become stranded during swallowing. These mechanisms define the food properties that must be avoided. By inverting the thinking, from hazards to ensuring safety, six criteria arise which are necessary for a safe-to-swallow bolus. A new conceptual model is proposed to define when food is safe to swallow during mastication. This significantly advances earlier mouth models. The conceptual model proposed in this work provides a framework of decision-making to define when food is safe to swallow. This will be of interest to designers of dietary foods, foods for dysphagia sufferers and will aid the further development of mastication robots for preparation of artificial boluses for digestion research. It enables food designers to influence the swallow-point properties of their products. For example, a product may be designed to satisfy five of the criteria for a safe-to-swallow bolus, which means the sixth criterion and its attendant food properties define the swallow-point. Alongside other organoleptic factors, these

  20. The gross theory model for neutrino-nucleus cross-section

    International Nuclear Information System (INIS)

    Samana, A R; Barbero, C A; Krmpotic, F; Duarte, S B; Dimarco, A J

    2008-01-01

    The nuclear gross theory, originally formulated by Takahashi and Yamada (1969 Prog. Theor. Phys. 41 1470) for the β-decay, is applied to the electronic-neutrino nucleus reactions, employing a more realistic description of the energetics of the Gamow-Teller resonances. The model parameters are gauged from the most recent experimental data, both for β - -decay and electron capture, separately for even-even, even-odd, odd-odd and odd-even nuclei. The numerical estimates for neutrino-nucleus cross-sections agree fairly well with previous evaluations done within the framework of microscopic models. The formalism presented here can be extended to the heavy nuclei mass region, where weak processes are quite relevant, which is of astrophysical interest because of its applications in supernova explosive nucleosynthesis

  1. An Electronic Model of the ATLAS Phase-1 Upgrade Hadronic Endcap Calorimeter Front End Crate Baseplane

    CERN Document Server

    Porter, Ryan

    This thesis presents an electrical model of two pairs of interconnects of the ATLAS Phase-1 Upgrade Hadronic Endcap Front End Crate prototype baseplane. Stripline transmission lines of the baseplane are modeled using Keysight Technologies' Electromagnetic Professional's (EMPro) 3D electromagnetic simulation (Finite Element Method) and the connectors are modeled using built-in models in Keysight Technologies' Advanced Design System (ADS). The model is compared in both the time and frequency domain to measured Time Domain Reflectometer (TDR) traces and S-parameters. The S-parameters of the model are found to be within $5\\%$ of the measured S-parameters for transmission and reflection, and range from $25\\%$ below to $100\\%$ above for forward and backward crosstalk. To make comparisons with measurements, the cables used to connect the prototype HEC baseplane to the measurement system had to be included in the model. Plots of the S-parameters of a model without these cables are presented for one pair of interconne...

  2. Design and Analysis of a Bio-Inspired Wire-Driven Multi-Section Flexible Robot

    Directory of Open Access Journals (Sweden)

    Zheng Li

    2013-04-01

    Full Text Available This paper presents a bio-inspired wire-driven multi-section flexible robot. It is inspired by the snake skeleton and octopus arm muscle arrangements. The robot consists of three sections and each section is made up of several identical vertebras, which are articulated by both spherical joints and a flexible backbone. Each section is driven by two groups of wires, controlling the bending motion in X and Y directions. This design integrates the serpentine robots' structure and the continuum robots' actuation. As a result, it is more compact than traditional serpentine robots and has a higher positioning accuracy than typical continuum soft robots, such as OctArm V. A Kinematics model and a workspace model of the robot are developed based on the piece wise constant curvature assumption. To evaluate the design, a prototype is built and experiments are carried out. The average distal end positioning error is less than 4%. Characteristics of the wire-driven robot are also discussed, including the leverage effect and the manipulability under constraint. These features makes the proposed robot well suited to confined spaces, especially for working in minimally invasive surgery, nuclear reactor pipelines, disaster debris, etc.

  3. Test of Seal System for Flexible Pipe End Fitting

    DEFF Research Database (Denmark)

    Banke, Lars; Jensen, Thomas Gregers

    1999-01-01

    The purpose of the end fitting seal system is to ensure leak proof termination of flexible pipes. The seal system of an NKT end fitting normally consists of a number of ring joint gaskets mounted in a steel sleeve on the outside of the polymeric inner liner of the pipe. The seal system is activated...... by compression of the gaskets, thus using the geometry to establish a seal towards the inner liner of the pipe and the steel sleeve of the end fitting. This paper describes how the seal system of an end fitting can be tested using an autoclave. By regulating temperature and pressure, the seal system can...... be tested up to 130oC and 51.7 MPa. Pressure, temperature and the mechanical behaviours of the pipe are measured for use in further research. The set-up is used to test the efficiency of the seal system as function of parameters such as cross sectional shapes of the gaskets, tolerances between gaskets...

  4. Appendix F : finite element analysis of end region.

    Science.gov (United States)

    2013-03-01

    FE (finite element) modeling was conducted to 1) provide a better understanding of the : elastic behavior of the end region prior to cracking and 2) to evaluate the effects of bearing pad : stiffness and width on end region elastic stresses. The FEA ...

  5. Long-term oceanic changes prior the end-Triassic mass extinction

    Science.gov (United States)

    Clémence, Marie-Emilie; Mette, Wolfgang; Thibault, Nicolas; Korte, Christoph

    2014-05-01

    A number of potential causes and kill mechanisms have been proposed for the end-Triassic mass extinction such as palaeoclimatic and sea-level variations, massive volcanism and ocean acidification. Recent analysis of the stomatal index and density of fossil leaves and geochemical research on pedogenic carbonate nodules are suggestive of rising atmospheric CO2 concentration and fluctuating climate in the Rhaetian. It seems therefore probable that the end-Triassic event was preceded by large climatic fluctuations and environmental perturbations in the Rhaetian which might have partly affected the composition and diversity of the terrestrial and marine biota prior to the end-Triassic interval. The Northern Calcareous Alps (NCA) has long been favored for the study of the Rhaetian, since the GSSP of the Triassic/Jurassic (T/J) boundary and other important T/J sections are situated in this region. However, the most famous Rhaetian sections in the NCA are composed of carbonates from the Koessen Formation and were situated in a large isolated intraplatform Basin (the Eiberg Basin), bordered to the south-east by a well-developed coral reef in the NW of the Tethys border. Several Rhaetian sections composed of marls and shales of the Zlambach Formation were deposited at the same time on the other side of this reef, in the oceanic Halstatt Basin, which was in direct connection to the Tethys. Here, we present new results on sedimentology, stable isotope and trace element analysis of both intraplatform and oceanic basin deposits in the NCA. Intraplatform Rhaetian sections from the Koessen Formation bear a few minor intervals of shales with enrichments in organic matter, some of which are associated to carbon isotopic excursions. Oceanic sections from the Hallstatt Basin are characterized at the base by very cyclic marl-limestone alternations. Higher up in the section, sediments progressively turn into pure shale deposits and the top of the Formation is characterized by organic

  6. Magnetic field in the end region of the SSC quadrupole magnet

    International Nuclear Information System (INIS)

    Caspi, S.; Helm, M.; Laslett, L.J.

    1991-06-01

    Recent advances in methods of computing magnetic fields have made it possible to study the field in the end region of the SS quadrupole magnet in detail. The placement of conductor in the straight section, away from the ends, was designed to produce a practically pure quadrupole field in the two-dimensional sense. The ends of the coils were designed to produce a practically pure quadrupole field in the integral sense using a method that ignores the presence of the iron yoke. Subsequently, the effect of presence of the yoke on the field was analyzed. The paper presents the end configuration together with the computed integrated multipole components, local multipole components, and local field components. A comparison with measurements is included. 5 refs., 5 figs., 1 tab

  7. Introduction to the special section on mixture modeling in personality assessment.

    Science.gov (United States)

    Wright, Aidan G C; Hallquist, Michael N

    2014-01-01

    Latent variable models offer a conceptual and statistical framework for evaluating the underlying structure of psychological constructs, including personality and psychopathology. Complex structures that combine or compare categorical and dimensional latent variables can be accommodated using mixture modeling approaches, which provide a powerful framework for testing nuanced theories about psychological structure. This special series includes introductory primers on cross-sectional and longitudinal mixture modeling, in addition to empirical examples applying these techniques to real-world data collected in clinical settings. This group of articles is designed to introduce personality assessment scientists and practitioners to a general latent variable framework that we hope will stimulate new research and application of mixture models to the assessment of personality and its pathology.

  8. An alternate end design for SSC dipoles

    International Nuclear Information System (INIS)

    Peters, C.; Caspi, S.; Taylor, C.

    1989-02-01

    Experience in the SSC dipole program has shown that fabrication of cylindrical coil ends is difficult. Cable stiffness requires large forces to maintain the proper position of the conductors in the end during winding. After winding, the coil ends remain distorted nd significant motion of the need conductors is required to force the coil end into the molding cavity. Local mechanical stresses are high during this process and extra pieces of insulation are required to prevent turn-to-turn shorts from developing during the winding and molding steps. Prior to assembly the coil end is compressed in a mold cavity and injected with a filler material to correct surface irregularities and fill voids in the end. LBL has developed an alternate design which permits the conductors to be wound over the end using minimal force and technician coerosion. The conductors are placed on a conical surface where the largest diameter over the outer layer conductors is 10 cm. No coil end spaces or insulation pieces between turns are required. The conductor geometry was analytically optimized to meet SSC multipole requirements for the ends. The first 1-m dipole utilizing this end geometry has been constructed and successfully tested. Design and construction data are presented. Also model test results, including training and multipole measurements of the end are given. 1 ref., 12 figs., 3 tabs

  9. DEF: an automated dead-end filling approach based on quasi-endosymbiosis.

    Science.gov (United States)

    Liu, Lili; Zhang, Zijun; Sheng, Taotao; Chen, Ming

    2017-02-01

    Gap filling for the reconstruction of metabolic networks is to restore the connectivity of metabolites via finding high-confidence reactions that could be missed in target organism. Current methods for gap filling either fall into the network topology or have limited capability in finding missing reactions that are indirectly related to dead-end metabolites but of biological importance to the target model. We present an automated dead-end filling (DEF) approach, which is derived from the wisdom of endosymbiosis theory, to fill gaps by finding the most efficient dead-end utilization paths in a constructed quasi-endosymbiosis model. The recalls of reactions and dead ends of DEF reach around 73% and 86%, respectively. This method is capable of finding indirectly dead-end-related reactions with biological importance for the target organism and is applicable to any given metabolic model. In the E. coli iJR904 model, for instance, about 42% of the dead-end metabolites were fixed by our proposed method. DEF is publicly available at http://bis.zju.edu.cn/DEF/. mchen@zju.edu.cn Supplementary data are available at Bioinformatics online.

  10. Analytical solutions to SSC coil end design

    International Nuclear Information System (INIS)

    Bossert, R.C.; Brandt, J.S.; Carson, J.A.; Fulton, H.J.; Lee, G.C.; Cook, J.M.

    1989-03-01

    As part of the SCC magnet effort, Fermilab will build and test a series of one meter model SSC magnets. The coils in these magnets will be constructed with several different end configurations. These end designs must satisfy both mechanical and magnetic criteria. Only the mechanical problem will be addressed. Solutions will attempt to minimize stresses and provide internal support for the cable. Different end designs will be compared in an attempt to determine which is most appropriate for the SSC dipole. The mathematics required to create each end configuration will be described. The computer aided design, programming and machine technology needed to make the parts will be reviewed. 2 refs., 10 figs

  11. End-to-End Airplane Detection Using Transfer Learning in Remote Sensing Images

    Directory of Open Access Journals (Sweden)

    Zhong Chen

    2018-01-01

    Full Text Available Airplane detection in remote sensing images remains a challenging problem due to the complexity of backgrounds. In recent years, with the development of deep learning, object detection has also obtained great breakthroughs. For object detection tasks in natural images, such as the PASCAL (Pattern Analysis, Statistical Modelling and Computational Learning VOC (Visual Object Classes Challenge, the major trend of current development is to use a large amount of labeled classification data to pre-train the deep neural network as a base network, and then use a small amount of annotated detection data to fine-tune the network for detection. In this paper, we use object detection technology based on deep learning for airplane detection in remote sensing images. In addition to using some characteristics of remote sensing images, some new data augmentation techniques have been proposed. We also use transfer learning and adopt a single deep convolutional neural network and limited training samples to implement end-to-end trainable airplane detection. Classification and positioning are no longer divided into multistage tasks; end-to-end detection attempts to combine them for optimization, which ensures an optimal solution for the final stage. In our experiment, we use remote sensing images of airports collected from Google Earth. The experimental results show that the proposed algorithm is highly accurate and meaningful for remote sensing object detection.

  12. Linear Modeling of the Three-Phase Diode Front-Ends with Reduced Capacitance Considering the Continuous Conduction Mode

    DEFF Research Database (Denmark)

    Máthé, Lászlo; Yang, Feng; Wang, Dong

    2016-01-01

    for the entire drive systems have to be designed. A linearization and simplification to single phase model can be performed; however, when inductance is present at the grid side its performance is not satisfactory. The problem is mainly caused by neglecting the continuous conduction mode of the rectifier......Reducing the DC-link capacitance considerably is a new trend in many applications, such as: motor drives, electrolysers etc.. A straight forward method for modelling the diode front-end is to build a non-linear diode based model. This non-linear model gives difficulties when the controllers...... in the simplified model. This article proposes a simplified linear model where the continuous conduction mode is also considered. The DC-link voltage and current waveforms obtained through the proposed simplified model matches very well the waveforms obtained with the three phase diode based model and also...

  13. 17 CFR 270.6c-10 - Exemption for certain open-end management investment companies to impose deferred sales loads.

    Science.gov (United States)

    2010-04-01

    ... management investment companies to impose deferred sales loads. 270.6c-10 Section 270.6c-10 Commodity and... ACT OF 1940 § 270.6c-10 Exemption for certain open-end management investment companies to impose... purposes of this section: (1) Company means a registered open-end management investment company, other than...

  14. Large animal model of functional tricuspid regurgitation in pacing induced end-stage heart failure.

    Science.gov (United States)

    Malinowski, Marcin; Proudfoot, Alistair G; Langholz, David; Eberhart, Lenora; Brown, Michael; Schubert, Hans; Wodarek, Jeremy; Timek, Tomasz A

    2017-06-01

    Functional tricuspid regurgitation (FTR) is common in patients with advanced heart failure and frequently complicates left ventricular assist device implantation yet remains poorly understood. We set out to establish large animal model of FTR that could serve as a research platform to investigate the pathogenesis of FTR associated with end-stage heart failure. : Through right thoracotomy, ten adult sheep underwent implantation of pacemaker with epicardial LV lead, five sonomicrometry crystals on the right ventricle, and left and right ventricular telemetry pressure sensors during a beating heart off-pump procedure. After 5 ± 1 days of recovery, baseline haemodynamic, echocardiographic and sonomicrometry data were collected. Animals were paced thereafter at a rate of 220-240 beats/min until the development of heart failure and concomitant tricuspid regurgitation. : Three animals died during early recovery period and one during the pacing phase. Six surviving animals were paced for a mean of 14 ± 5 days. Cardiac function was significantly depressed compared to baseline, with LV ejection fraction falling from 69 ± 2% to 22 ± 4% ( P  tricuspid annulus (from 29.5 ± 1.6 to 36.5 ± 4.5 mm; P  = 0.01) and right ventricle (from 21.9 ± 0.2 to 30.3 ± 0.6 mm; P  = 0.03). Sonomicrometry derived contractility of RV free wall was depressed and at least moderate tricuspid insufficiency developed in all animals. : Biventricular dysfunction, tricuspid annular dilatation and significant FTR were observed in our model of ovine tachycardia induced cardiomyopathy. This animal model reflects the clinical situation of end-stage heart failure patients presenting for mechanical support. © The Author 2017. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

  15. Modeling and Negotiating Service Quality

    Science.gov (United States)

    Benbernou, Salima; Brandic, Ivona; Cappiello, Cinzia; Carro, Manuel; Comuzzi, Marco; Kertész, Attila; Kritikos, Kyriakos; Parkin, Michael; Pernici, Barbara; Plebani, Pierluigi

    In this chapter the research problems of specifying and negotiating QoS and its corresponding quality documents are analyzed. For this reason, this chapter is separated into two main sections, Section 6.1 and 6.2, with each dedicated to one of the two problems, i.e., QoS specification and negotiation, respectively. Each section has a similar structure: they first introduce the problem and then, in the remaining subsections, review related work. Finally, the chapter ends with Section 6.3, which identifies research gaps and presents potential research challenges in QoS modelling, specification and negotiation.

  16. Selected System Models

    Science.gov (United States)

    Schmidt-Eisenlohr, F.; Puñal, O.; Klagges, K.; Kirsche, M.

    Apart from the general issue of modeling the channel, the PHY and the MAC of wireless networks, there are specific modeling assumptions that are considered for different systems. In this chapter we consider three specific wireless standards and highlight modeling options for them. These are IEEE 802.11 (as example for wireless local area networks), IEEE 802.16 (as example for wireless metropolitan networks) and IEEE 802.15 (as example for body area networks). Each section on these three systems discusses also at the end a set of model implementations that are available today.

  17. Testing Cross-Sectional Correlation in Large Panel Data Models with Serial Correlation

    Directory of Open Access Journals (Sweden)

    Badi H. Baltagi

    2016-11-01

    Full Text Available This paper considers the problem of testing cross-sectional correlation in large panel data models with serially-correlated errors. It finds that existing tests for cross-sectional correlation encounter size distortions with serial correlation in the errors. To control the size, this paper proposes a modification of Pesaran’s Cross-sectional Dependence (CD test to account for serial correlation of an unknown form in the error term. We derive the limiting distribution of this test as N , T → ∞ . The test is distribution free and allows for unknown forms of serial correlation in the errors. Monte Carlo simulations show that the test has good size and power for large panels when serial correlation in the errors is present.

  18. Mixtures of endocrine disrupting contaminants modelled on human high end exposures

    DEFF Research Database (Denmark)

    Christiansen, Sofie; Kortenkamp, A.; Petersen, Marta Axelstad

    2012-01-01

    exceeding 1 is expected to lead to effects in the rat, a total dose more than 62 times higher than human exposures should lead to responses. Considering the high uncertainty of this estimate, experience on lowest‐observed‐adverse‐effect‐level (LOAEL)/NOAEL ratios and statistical power of rat studies, we...... expected that combined doses 150 times higher than high end human intake estimates should give no, or only borderline effects, whereas doses 450 times higher should produce significant responses. Experiments indeed showed clear developmental toxicity of the 450‐fold dose in terms of increased nipple...... though each individual chemical is present at low, ineffective doses, but the effects of mixtures modelled based on human intakes have not previously been investigated. To address this issue for the first time, we selected 13 chemicals for a developmental mixture toxicity study in rats where data about...

  19. Revisiting the T2K data using different models for the neutrino-nucleus cross sections

    Energy Technology Data Exchange (ETDEWEB)

    Meloni, D., E-mail: meloni@fis.uniroma3.it [Dipartimento di Fisica ' E. Amaldi' , Universita degli Studi Roma Tre, Via della Vasca Navale 84, 00146 Roma (Italy); Martini, M., E-mail: mmartini@ulb.ac.be [Institut d' Astronomie et d' Astrophysique, CP-226, Universite Libre de Bruxelles, 1050 Brussels (Belgium)

    2012-09-17

    We present a three-flavor fit to the recent {nu}{sub {mu}}{yields}{nu}{sub e} and {nu}{sub {mu}}{yields}{nu}{sub {mu}} T2K oscillation data with different models for the neutrino-nucleus cross section. We show that, even for a limited statistics, the allowed regions and best fit points in the ({theta}{sub 13},{delta}{sub CP}) and ({theta}{sub 23},{Delta}m{sub atm}{sup 2}) planes are affected if, instead of using the Fermi gas model to describe the quasielastic cross section, we employ a model including the multinucleon emission channel.

  20. Modelling end-glacial earthquakes at Olkiluoto. Expansion of the 2010 study

    Energy Technology Data Exchange (ETDEWEB)

    Faelth, B.; Hoekmark, H. [Clay Technology AB, Lund (Sweden)

    2012-02-15

    The present report is an extension of Posiva working report 2011-13: 'Modelling end-glacial earthquakes at Olkiluoto'. The modelling methodology and most parameter values are identical to those used in that report. The main objective is the same: to obtain conservative estimates of fracture shear displacements induced by end-glacial earthquakes occurring on verified deformation zones at the Olkiluoto site. The remotely activated rock fractures (with their fracture centres positioned at different distances around the potential earthquake fault being considered) are called 'target fractures'. As in the previous report, all target fractures were assumed to be perfectly planar and circular with a radius of 75 m. Compared to the previous study, the result catalogue is more complete. One additional deformation zone (i.e. potential earthquake fault) has been included (BFZ039), whereas one deformation zone that appeared to produce only insignificant target fracture disturbances (BFZ214) is omitted. For each of the three zones considered here (BFZ021, BFZ039, and BFZ100), four models, each with a different orientation of the target fractures surrounding the fault, are analysed. Three of these four sets were included in the previous report, however not as systematically as here where each of the four fracture orientations is tried in all fracture positions. As in the previous study, seismic moments and moment magnitudes are as high as reasonably possible, given the sizes and orientations of the zones, i.e., the earthquakes release the largest possible amount of strain energy. The strain energy release is restricted only by a low residual fault shear strength applied to suppress post-rupture fault oscillations. Moment magnitudes are: 5.8 (BFZ021), 3.9 (BFZ039) and 4.3 (BFZ100). For the BFZ100 model, the sensitivity of the results to variations in fracture shear strength is checked. The BFZ021 and BFZ100 models are analyzed for two additional in situ stress

  1. The upper end of climate model temperature projections is inconsistent with past warming

    International Nuclear Information System (INIS)

    Stott, Peter; Good, Peter; Jones, Gareth; Gillett, Nathan; Hawkins, Ed

    2013-01-01

    Climate models predict a large range of possible future temperatures for a particular scenario of future emissions of greenhouse gases and other anthropogenic forcings of climate. Given that further warming in coming decades could threaten increasing risks of climatic disruption, it is important to determine whether model projections are consistent with temperature changes already observed. This can be achieved by quantifying the extent to which increases in well mixed greenhouse gases and changes in other anthropogenic and natural forcings have already altered temperature patterns around the globe. Here, for the first time, we combine multiple climate models into a single synthesized estimate of future warming rates consistent with past temperature changes. We show that the observed evolution of near-surface temperatures appears to indicate lower ranges (5–95%) for warming (0.35–0.82 K and 0.45–0.93 K by the 2020s (2020–9) relative to 1986–2005 under the RCP4.5 and 8.5 scenarios respectively) than the equivalent ranges projected by the CMIP5 climate models (0.48–1.00 K and 0.51–1.16 K respectively). Our results indicate that for each RCP the upper end of the range of CMIP5 climate model projections is inconsistent with past warming. (letter)

  2. Cross-section parameterization of the pebble bed modular reactor using the dimension-wise expansion model

    International Nuclear Information System (INIS)

    Zivanovic, Rastko; Bokov, Pavel M.

    2010-01-01

    This paper discusses the use of the dimension-wise expansion model for cross-section parameterization. The components of the model were approximated with tensor products of orthogonal polynomials. As we demonstrate, the model for a specific cross-section can be built in a systematic way directly from data without any a priori knowledge of its structure. The methodology is able to construct a finite basis of orthogonal polynomials that is required to approximate a cross-section with pre-specified accuracy. The methodology includes a global sensitivity analysis that indicates irrelevant state parameters which can be excluded from the model without compromising the accuracy of the approximation and without repetition of the fitting process. To fit the dimension-wise expansion model, Randomised Quasi-Monte-Carlo Integration and Sparse Grid Integration methods were used. To test the parameterization methods with different integrations embedded we have used the OECD PBMR 400 MW benchmark problem. It has been shown in this paper that the Sparse Grid Integration achieves pre-specified accuracy with a significantly (up to 1-2 orders of magnitude) smaller number of samples compared to Randomised Quasi-Monte-Carlo Integration.

  3. The end-to-end testbed of the optical metrology system on-board LISA Pathfinder

    Energy Technology Data Exchange (ETDEWEB)

    Steier, F; Cervantes, F Guzman; Marin, A F GarcIa; Heinzel, G; Danzmann, K [Max-Planck-Institut fuer Gravitationsphysik (Albert-Einstein-Institut) and Universitaet Hannover (Germany); Gerardi, D, E-mail: frank.steier@aei.mpg.d [EADS Astrium Satellites GmbH, Friedrichshafen (Germany)

    2009-05-07

    LISA Pathfinder is a technology demonstration mission for the Laser Interferometer Space Antenna (LISA). The main experiment on-board LISA Pathfinder is the so-called LISA Technology Package (LTP) which has the aim to measure the differential acceleration between two free-falling test masses with an accuracy of 3 x 10{sup -14} ms{sup -2} Hz{sup -1/2} between 1 mHz and 30 mHz. This measurement is performed interferometrically by the optical metrology system (OMS) on-board LISA Pathfinder. In this paper, we present the development of an experimental end-to-end testbed of the entire OMS. It includes the interferometer and its sub-units, the interferometer backend which is a phasemeter and the processing of the phasemeter output data. Furthermore, three-axes piezo-actuated mirrors are used instead of the free-falling test masses for the characterization of the dynamic behaviour of the system and some parts of the drag-free and attitude control system (DFACS) which controls the test masses and the satellite. The end-to-end testbed includes all parts of the LTP that can reasonably be tested on earth without free-falling test masses. At its present status it consists mainly of breadboard components. Some of those have already been replaced by engineering models of the LTP experiment. In the next steps, further engineering and flight models will also be inserted in this testbed and tested against well-characterized breadboard components. The presented testbed is an important reference for the unit tests and can also be used for validation of the on-board experiment during the mission.

  4. 17 CFR 274.11 - Form N-1, registration statement of open-end management investment companies.

    Science.gov (United States)

    2010-04-01

    ... statement of open-end management investment companies. 274.11 Section 274.11 Commodity and Securities Exchanges SECURITIES AND EXCHANGE COMMISSION (CONTINUED) FORMS PRESCRIBED UNDER THE INVESTMENT COMPANY ACT...(b) of the Investment Company Act of 1940 by open-end management investment companies that are...

  5. Modeling and Analysis of a Piezoelectric Energy Harvester with Varying Cross-Sectional Area

    Directory of Open Access Journals (Sweden)

    Maiara Rosa

    2014-01-01

    Full Text Available This paper reports on the modeling and on the experimental verification of electromechanically coupled beams with varying cross-sectional area for piezoelectric energy harvesting. The governing equations are formulated using the Rayleigh-Ritz method and Euler-Bernoulli assumptions. A load resistance is considered in the electrical domain for the estimate of the electric power output of each geometric configuration. The model is first verified against the analytical results for a rectangular bimorph with tip mass reported in the literature. The experimental verification of the model is also reported for a tapered bimorph cantilever with tip mass. The effects of varying cross-sectional area and tip mass on the electromechanical behavior of piezoelectric energy harvesters are also discussed. An issue related to the estimation of the optimal load resistance (that gives the maximum power output on beam shape optimization problems is also discussed.

  6. Overview of statistical methods, models and analysis for predicting equipment end of life

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-07-01

    Utility equipment can be operated and maintained for many years following installation. However, as the equipment ages, utility operators must decide whether to extend the service life or replace the equipment. Condition assessment modelling is used by many utilities to determine the condition of equipment and to prioritize the maintenance or repair. Several factors are weighted and combined in assessment modelling, which gives a single index number to rate the equipment. There is speculation that this index alone may not be adequate for a business case to rework or replace an asset because it only ranks an asset into a particular category. For that reason, a new methodology was developed to determine the economic end of life of an asset. This paper described the different statistical methods available and their use in determining the remaining service life of electrical equipment. A newly developed Excel-based demonstration computer tool is also an integral part of the deliverables of this project.

  7. Positive end-expiratory pressure improves survival in a rodent model of cardiopulmonary resuscitation using high-dose epinephrine.

    LENUS (Irish Health Repository)

    McCaul, Conán

    2009-10-01

    Multiple interventions have been tested in models of cardiopulmonary resuscitation (CPR) to optimize drug use, chest compressions, and ventilation. None has studied the effects of positive end-expiratory pressure (PEEP) on outcome. We hypothesized that because PEEP can reverse pulmonary atelectasis, lower pulmonary vascular resistance, and potentially improve cardiac output, its use during CPR would increase survival.

  8. 17 CFR 274.11A - Form N-1A, registration statement of open-end management investment companies.

    Science.gov (United States)

    2010-04-01

    ... statement of open-end management investment companies. 274.11A Section 274.11A Commodity and Securities...(b) of the Investment Company Act of 1940 by open-end management investment companies other than... registration under the Securities Act of 1933 of the securities of all open-end management investment companies...

  9. A novel end-to-end classifier using domain transferred deep convolutional neural networks for biomedical images.

    Science.gov (United States)

    Pang, Shuchao; Yu, Zhezhou; Orgun, Mehmet A

    2017-03-01

    Highly accurate classification of biomedical images is an essential task in the clinical diagnosis of numerous medical diseases identified from those images. Traditional image classification methods combined with hand-crafted image feature descriptors and various classifiers are not able to effectively improve the accuracy rate and meet the high requirements of classification of biomedical images. The same also holds true for artificial neural network models directly trained with limited biomedical images used as training data or directly used as a black box to extract the deep features based on another distant dataset. In this study, we propose a highly reliable and accurate end-to-end classifier for all kinds of biomedical images via deep learning and transfer learning. We first apply domain transferred deep convolutional neural network for building a deep model; and then develop an overall deep learning architecture based on the raw pixels of original biomedical images using supervised training. In our model, we do not need the manual design of the feature space, seek an effective feature vector classifier or segment specific detection object and image patches, which are the main technological difficulties in the adoption of traditional image classification methods. Moreover, we do not need to be concerned with whether there are large training sets of annotated biomedical images, affordable parallel computing resources featuring GPUs or long times to wait for training a perfect deep model, which are the main problems to train deep neural networks for biomedical image classification as observed in recent works. With the utilization of a simple data augmentation method and fast convergence speed, our algorithm can achieve the best accuracy rate and outstanding classification ability for biomedical images. We have evaluated our classifier on several well-known public biomedical datasets and compared it with several state-of-the-art approaches. We propose a robust

  10. Vaginal birth after caesarean section prediction models: a UK comparative observational study.

    Science.gov (United States)

    Mone, Fionnuala; Harrity, Conor; Mackie, Adam; Segurado, Ricardo; Toner, Brenda; McCormick, Timothy R; Currie, Aoife; McAuliffe, Fionnuala M

    2015-10-01

    Primarily, to assess the performance of three statistical models in predicting successful vaginal birth in patients attempting a trial of labour after one previous lower segment caesarean section (TOLAC). The statistically most reliable models were subsequently subjected to validation testing in a local antenatal population. A retrospective observational study was performed with study data collected from the Northern Ireland Maternity Service Database (NIMATs). The study population included all women that underwent a TOLAC (n=385) from 2010 to 2012 in a regional UK obstetric unit. Data was collected from the Northern Ireland Maternity Service Database (NIMATs). Area under the curve (AUC) and correlation analysis was performed. Of the three prediction models evaluated, AUC calculations for the Smith et al., Grobman et al. and Troyer and Parisi Models were 0.74, 0.72 and 0.65, respectively. Using the Smith et al. model, 52% of women had a low risk of caesarean section (CS) (predicted VBAC >72%) and 20% had a high risk of CS (predicted VBAC <60%), of whom 20% and 63% had delivery by CS. The fit between observed and predicted outcome in this study cohort using the Smith et al. and Grobman et al. models were greatest (Chi-square test, p=0.228 and 0.904), validating both within the population. The Smith et al. and Grobman et al. models could potentially be utilized within the UK to provide women with an informed choice when deciding on mode of delivery after a previous CS. Crown Copyright © 2015. Published by Elsevier Ireland Ltd. All rights reserved.

  11. Threshold law for ionization cross sections in the Temkin-Poet model

    International Nuclear Information System (INIS)

    Macek, J.H.; Ihra, W.

    1997-01-01

    An integral representation of wave functions for the Temkin-Poet model of electron impact on atomic hydrogen is given. Approximate wave functions are evaluated analytically for large hyperradius to extract the ionization S-matrix element. An ionization cross section of the form exp[-aE -1/6 +bE 1/6 ], where a and b are positive constants, is derived. The exponential suppression of ionization for small E appears to be the quantum counterpart of the delayed onset of ionization in the classical theory for this model. copyright 1997 The American Physical Society

  12. Issues on generating primordial anisotropies at the end of inflation

    Energy Technology Data Exchange (ETDEWEB)

    Emami, Razieh; Firouzjahi, Hassan, E-mail: emami@mail.ipm.ir, E-mail: firouz@mail.ipm.ir [School of Physics, Institute for Research in Fundamental Sciences (IPM), P.O. Box 19395-5531, Tehran (Iran, Islamic Republic of)

    2012-01-01

    We revisit the idea of generating primordial anisotropies at the end of inflation in models of inflation with gauge fields. To be specific we consider the charged hybrid inflation model where the waterfall field is charged under a U(1) gauge field so the surface of end of inflation is controlled both by inflaton and the gauge fields. Using δN formalism properly we find that the anisotropies generated at the end of inflation from the gauge field fluctuations are exponentially suppressed on cosmological scales. This is because the gauge field evolves exponentially during inflation while in order to generate appreciable anisotropies at the end of inflation the spectator gauge field has to be frozen. We argue that this is a generic feature, that is, one can not generate observable anisotropies at the end of inflation within an FRW background.

  13. Issues on generating primordial anisotropies at the end of inflation

    International Nuclear Information System (INIS)

    Emami, Razieh; Firouzjahi, Hassan

    2012-01-01

    We revisit the idea of generating primordial anisotropies at the end of inflation in models of inflation with gauge fields. To be specific we consider the charged hybrid inflation model where the waterfall field is charged under a U(1) gauge field so the surface of end of inflation is controlled both by inflaton and the gauge fields. Using δN formalism properly we find that the anisotropies generated at the end of inflation from the gauge field fluctuations are exponentially suppressed on cosmological scales. This is because the gauge field evolves exponentially during inflation while in order to generate appreciable anisotropies at the end of inflation the spectator gauge field has to be frozen. We argue that this is a generic feature, that is, one can not generate observable anisotropies at the end of inflation within an FRW background

  14. 48 CFR 52.222-18 - Certification Regarding Knowledge of Child Labor for Listed End Products.

    Science.gov (United States)

    2010-10-01

    ... for Listed End Products. As prescribed in 22.1505(a), insert the following provision: Certification... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Certification Regarding Knowledge of Child Labor for Listed End Products. 52.222-18 Section 52.222-18 Federal Acquisition...

  15. 40 CFR 63.495 - Back-end process provisions-procedures to determine compliance using stripping technology.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Back-end process provisions-procedures to determine compliance using stripping technology. 63.495 Section 63.495 Protection of Environment...: Group I Polymers and Resins § 63.495 Back-end process provisions—procedures to determine compliance...

  16. Interoperable End-to-End Remote Patient Monitoring Platform Based on IEEE 11073 PHD and ZigBee Health Care Profile.

    Science.gov (United States)

    Clarke, Malcolm; de Folter, Joost; Verma, Vivek; Gokalp, Hulya

    2018-05-01

    This paper describes the implementation of an end-to-end remote monitoring platform based on the IEEE 11073 standards for personal health devices (PHD). It provides an overview of the concepts and approaches and describes how the standard has been optimized for small devices with limited resources of processor, memory, and power that use short-range wireless technology. It explains aspects of IEEE 11073, including the domain information model, state model, and nomenclature, and how these support its plug-and-play architecture. It shows how these aspects underpin a much larger ecosystem of interoperable devices and systems that include IHE PCD-01, HL7, and BlueTooth LE medical devices, and the relationship to the Continua Guidelines, advocating the adoption of data standards and nomenclature to support semantic interoperability between health and ambient assisted living in future platforms. The paper further describes the adaptions that have been made in order to implement the standard on the ZigBee Health Care Profile and the experiences of implementing an end-to-end platform that has been deployed to frail elderly patients with chronic disease(s) and patients with diabetes.

  17. Negative emotionality across diagnostic models: RDoC, DSM-5 Section III, and FFM.

    Science.gov (United States)

    Gore, Whitney L; Widiger, Thomas A

    2018-03-01

    The research domain criteria (RDoC) were established in an effort to explore underlying dimensions that cut across many existing disorders and to provide an alternative to the Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition (DSM-5). One purpose of the present study was to suggest a potential alignment of RDoC negative valence with 2 other dimensional models of negative emotionality: five-factor model (FFM) neuroticism and the DSM-5 Section III negative affectivity. A second purpose of the study, though, was to compare their coverage of negative emotionality, more specifically with respect to affective instability. Participants were adult community residents (N = 90) currently in mental health treatment. Participants received self-report measures of RDoC negative valence, FFM neuroticism, and DSM-5 Section III negative affectivity, along with measures of affective instability, borderline personality disorder, and impairment. Findings suggested that RDoC negative valence is commensurate with FFM neuroticism and DSM-5 Section III negative affectivity, and it would be beneficial if it was expanded to include affective instability. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  18. The end point of the first-order phase transition of the SU(2) gauge-Higgs model on a four-dimensional isotropic lattice

    International Nuclear Information System (INIS)

    Aoki, Y.; Csikor, F.; Fodor, Z.; Ukawa, A.

    1999-01-01

    We report results of a study of the end point of the electroweak phase transition of the SU(2) gauge-Higgs model defined on a four-dimensional isotropic lattice with N t = 2. Finite-size scaling study of Lee-Yang zeros yields λ c = 0.00116(16) for the end point. Combined with a zero-temperature measurement of Higgs and W boson masses, this leads to M H,c = 68.2 ± 6.6 GeV for the critical Higgs boson mass. An independent analysis of Binder cumulant gives a consistent value λ c = 0.00102(3) for the end point

  19. Modeling the fate and end-of-life phase of engineered nanomaterials in the Japanese construction sector.

    Science.gov (United States)

    Suzuki, Shinya; Part, Florian; Matsufuji, Yasushi; Huber-Humer, Marion

    2018-02-01

    To date construction materials that contain engineered nanomaterials (ENMs) are available at the markets, but at the same time very little is known about their environmental fate. Therefore, this study aimed at modeling the potential fate of ENMs by using the example of the Japanese construction sector and by conducting a dynamic material flow analysis. Expert interviews and national reports revealed that about 3920-4660 tons of ENMs are annually used for construction materials in Japan. Nanoscale TiO 2 , SiO 2 , Al 2 O 3 and carbon black have already been applied for decades to wall paints, road markings or concrete. The dynamic material flow model indicates that in 2016 about 95% of ENMs, which have been used since their year of market penetration, remained in buildings, whereas only 5% ended up in the Japanese waste management system or were diffusely released into the environment. Considering the current Japanese waste management system, ENMs were predicted to end up in recycled materials (40-47%) or in landfills (36-41%). It was estimated that only a small proportion was used in agriculture (5-7%, as ENM-containing sewage sludges) or was diffusely released into soils, surface waters or the atmosphere (5-19%). The results indicate that ENM release predominantly depend on their specific applications and characteristics. The model also highlights the importance of adequate collection and treatment of ENM-containing wastes. In future, similar dynamic flow models for other countries should consider, inasmuch as available, historical data on ENM production (e.g. like declaration reports that are annually published by relevant public authorities or associations), as such input data is very important regarding data reliability in order to decrease uncertainties and to continuously improve model accuracy. In addition, more environmental monitoring studies that aim at the quantification of ENM release and inadvertent transfer, particularly triggered by waste treatment

  20. SampleCNN: End-to-End Deep Convolutional Neural Networks Using Very Small Filters for Music Classification

    Directory of Open Access Journals (Sweden)

    Jongpil Lee

    2018-01-01

    Full Text Available Convolutional Neural Networks (CNN have been applied to diverse machine learning tasks for different modalities of raw data in an end-to-end fashion. In the audio domain, a raw waveform-based approach has been explored to directly learn hierarchical characteristics of audio. However, the majority of previous studies have limited their model capacity by taking a frame-level structure similar to short-time Fourier transforms. We previously proposed a CNN architecture which learns representations using sample-level filters beyond typical frame-level input representations. The architecture showed comparable performance to the spectrogram-based CNN model in music auto-tagging. In this paper, we extend the previous work in three ways. First, considering the sample-level model requires much longer training time, we progressively downsample the input signals and examine how it affects the performance. Second, we extend the model using multi-level and multi-scale feature aggregation technique and subsequently conduct transfer learning for several music classification tasks. Finally, we visualize filters learned by the sample-level CNN in each layer to identify hierarchically learned features and show that they are sensitive to log-scaled frequency.

  1. A Non-Linear Finite Element Model for the LHC Main Dipole Coil Cross-Section

    CERN Document Server

    Pojer, M; Scandale, Walter

    2006-01-01

    The production of the dipole magnets for the Large Hadron Collider is at its final stage. Nevertheless, some mechanical instabilities are still observed for which no clear explanation has been found yet. A FE modelization of the dipole cold mass cross-section had already been developed at CERN, mainly for magnetic analysis, taking into account conductor blocks and a frictionless behavior. This paper describes a new ANSYS® model of the dipole coil cross-section, featuring individual turns inside conductor blocks, and implementing friction and the mechanical non-linear behavior of insulated cables. Preliminary results, comparison with measurements performed in industry and ongoing developments are discussed.

  2. Static end-expiratory and dynamic forced expiratory tracheal collapse in COPD

    International Nuclear Information System (INIS)

    O'Donnell, C.R.; Bankier, A.A.; O'Donnell, D.H.; Loring, S.H.; Boiselle, P.M.

    2014-01-01

    Aim: To determine the range of tracheal collapse at end-expiration among chronic obstructive pulmonary disease (COPD) patients and to compare the extent of tracheal collapse between static end-expiratory and dynamic forced-expiratory multidetector-row computed tomography (MDCT). Materials and methods: After institutional review board approval and obtaining informed consent, 67 patients meeting the National Heart, Lung, and Blood Institute (NHLBI)/World Health Organization (WHO) Global Initiative for Chronic Obstructive Lung Disease (GOLD) criteria for COPD were sequentially imaged using a 64-detector-row CT machine at end-inspiration, during forced expiration, and at end-expiration. Standardized respiratory coaching and spirometric monitoring were employed. Mean percentage tracheal collapse at end-expiration and forced expiration were compared using correlation analysis, and the power of end-expiratory cross-sectional area to predict excessive forced-expiratory tracheal collapse was computed following construction of receiver operating characteristic (ROC) curves. Results: Mean percentage expiratory collapse among COPD patients was 17 ± 18% at end-expiration compared to 62 ± 16% during forced expiration. Over the observed range of end-expiratory tracheal collapse (approximately 10–50%), the positive predictive value of end-expiratory collapse to predict excessive (≥80%) forced expiratory tracheal collapse was <0.3. Conclusion: COPD patients demonstrate a wide range of end-expiratory tracheal collapse. The magnitude of static end-expiratory tracheal collapse does not predict excessive dynamic expiratory tracheal collapse

  3. Determination of Ultimate Torque for Multiply Connected Cross Section Rod

    Directory of Open Access Journals (Sweden)

    V. L. Danilov

    2015-01-01

    Full Text Available The aim of this work is to determine load-carrying capability of the multiply cross-section rod. This calculation is based on the model of the ideal plasticity of the material, so that the desired ultimate torque is a torque at which the entire cross section goes into a plastic state.The article discusses the cylindrical multiply cross-section rod. To satisfy the equilibrium equation and the condition of plasticity simultaneously, two stress function Ф and φ are introduced. By mathematical transformations it has been proved that Ф is constant along the path, and a formula to find its values on the contours has been obtained. The paper also presents the rationale of the line of stress discontinuity and obtained relationships, which allow us to derive the equations break lines for simple interaction of neighboring circuits, such as two lines, straight lines and circles, circles and a different sign of the curvature.After substitution into the boundary condition at the end of the stress function Ф and mathematical transformations a formula is obtained to determine the ultimate torque for the multiply cross-section rod.Using the doubly connected cross-section and three-connected cross-section rods as an example the application of the formula of ultimate torque is studied.For doubly connected cross-section rod, the paper offers a formula of the torque versus the radius of the rod, the aperture radius and the distance between their centers. It also clearly demonstrates the torque dependence both on the ratio of the radii and on the displacement of hole. It is shown that the value of the torque is more influenced by the displacement of hole, rather than by the ratio of the radii.For the three-connected cross-section rod the paper shows the integration feature that consists in selection of a coordinate system. As an example, the ultimate torque is found by two methods: analytical one and 3D modeling. The method of 3D modeling is based on the Nadai

  4. CHEETAH: circuit-switched high-speed end-to-end transport architecture

    Science.gov (United States)

    Veeraraghavan, Malathi; Zheng, Xuan; Lee, Hyuk; Gardner, M.; Feng, Wuchun

    2003-10-01

    Leveraging the dominance of Ethernet in LANs and SONET/SDH in MANs and WANs, we propose a service called CHEETAH (Circuit-switched High-speed End-to-End Transport ArcHitecture). The service concept is to provide end hosts with high-speed, end-to-end circuit connectivity on a call-by-call shared basis, where a "circuit" consists of Ethernet segments at the ends that are mapped into Ethernet-over-SONET long-distance circuits. This paper focuses on the file-transfer application for such circuits. For this application, the CHEETAH service is proposed as an add-on to the primary Internet access service already in place for enterprise hosts. This allows an end host that is sending a file to first attempt setting up an end-to-end Ethernet/EoS circuit, and if rejected, fall back to the TCP/IP path. If the circuit setup is successful, the end host will enjoy a much shorter file-transfer delay than on the TCP/IP path. To determine the conditions under which an end host with access to the CHEETAH service should attempt circuit setup, we analyze mean file-transfer delays as a function of call blocking probability in the circuit-switched network, probability of packet loss in the IP network, round-trip times, link rates, and so on.

  5. Exercise starts and ends in the brain.

    Science.gov (United States)

    Kayser, Bengt

    2003-10-01

    Classically the limit to endurance of exercise is explained in terms of metabolic capacity. Cardio-respiratory capacity and muscle fatigue are thought to set the limit and the majority of studies on factors limiting endurance exercise discuss issues such as maximal oxygen uptake (VO2max), aerobic enzyme capacity, cardiac output, glycogen stores, etc. However, this paradigm does not explain the limitation to endurance exercise with large muscle groups at altitude, when at exhaustion exercise is ended without limb locomotor muscle fatigue and with sub-maximal cardiac output. A simple fact provides a basis for an explanation. Voluntary exercise starts and ends in the brain. It starts with spatial and temporal recruitment of motor units and ends with their de-recruitment. A conscious decision precedes a voluntary effort. The end of effort is again volitional and a forced conscious decision to stop precedes it, but it is unknown what forces the off-switch of recruitment at exhaustion although sensation of exertion certainly plays a role. An alternative model explaining the limitation of exercise endurance thus proposes that the central nervous system integrates input from various sources all related to the exercise and limits the intensity and duration of recruitment of limb skeletal muscle to prevent jeopardizing the integrity of the organism. This model acknowledges the cardio-respiratory and muscle metabolic capacities as prime actors on the performance scene, while crediting the central nervous system for its pivotal role as the ultimate site where exercise starts and ends.

  6. The LXCat project: Electron scattering cross sections and swarm parameters for low temperature plasma modeling

    International Nuclear Information System (INIS)

    Pancheshnyi, S.; Biagi, S.; Bordage, M.C.; Hagelaar, G.J.M.; Morgan, W.L.; Phelps, A.V.; Pitchford, L.C.

    2012-01-01

    Graphical abstract: LXCat is an open-access website containing data needed for low temperature plasma modeling as well as on-line tools useful for their manipulation. Highlights: ► LXCat: an open-access website with data for low temperature plasma modeling. ► Contains compilations of electron scattering cross sections and transport data. ► Data from different contributors for many neutral, ground-state species. ► On-line tools for browsing, plotting, up/downloading data. ► On-line Boltzmann solver for calculating electron swarm parameters. - Abstract: LXCat is a dynamic, open-access, website for collecting, displaying, and downloading ELECtron SCATtering cross sections and swarm parameters (mobility, diffusion coefficient, reaction rates, etc.) required for modeling low temperature, non-equilibrium plasmas. Contributors set up individual databases, and the available databases, indicated by the contributor’s chosen title, include mainly complete sets of electron-neutral scattering cross sections, although the option for introducing partial sets of cross sections exists. A database for measured swarm parameters is also part of LXCat, and this is a growing activity. On-line tools include options for browsing, plotting, and downloading cross section data. The electron energy distribution functions (edfs) in low temperature plasmas are in general non-Maxwellian, and LXCat provides an option for execution of an on-line Boltzmann equation solver to calculate the edf in homogeneous electric fields. Thus, the user can obtain electron transport and rate coefficients (averages over the edfs) in pure gases or gas mixtures over a range of values of the reduced electric fields strength, E/N, the ratio of the electric field strength to the neutral density, using cross sections from the available databases. New contributors are welcome and anyone wishing to create a database and upload data can request a username and password. LXCat is part of a larger, community

  7. Euthanasia embedded in palliative care. Responses to essentialistic criticisms of the Belgian model of integral end-of-life care.

    Science.gov (United States)

    Bernheim, Jan L; Raus, Kasper

    2017-08-01

    The Belgian model of 'integral' end-of-life care consists of universal access to palliative care (PC) and legally regulated euthanasia. As a first worldwide, the Flemish PC organisation has embedded euthanasia in its practice. However, some critics have declared the Belgian-model concepts of 'integral PC' and 'palliative futility' to fundamentally contradict the essence of PC. This article analyses the various essentialistic arguments for the incompatibility of euthanasia and PC. The empirical evidence from the euthanasia-permissive Benelux countries shows that since legalisation, carefulness (of decision making) at the end of life has improved and there have been no significant adverse 'slippery slope' effects. It is problematic that some critics disregard the empirical evidence as epistemologically irrelevant in a normative ethical debate. Next, rejecting euthanasia because its prevention was a founding principle of PC ignores historical developments. Further, critics' ethical positions depart from the PC tenet of patient centeredness by prioritising caregivers' values over patients' values. Also, many critics' canonical adherence to the WHO definition of PC, which has intention as the ethical criterion is objectionable. A rejection of the Belgian model on doctrinal grounds also has nefarious practical consequences such as the marginalisation of PC in euthanasia-permissive countries, the continuation of clandestine practices and problematic palliative sedation until death. In conclusion, major flaws of essentialistic arguments against the Belgian model include the disregard of empirical evidence, appeals to canonical and questionable definitions, prioritisation of caregiver perspectives over those of patients and rejection of a plurality of respectable views on decision making at the end of life. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  8. Dynamic Model for the Z Accelerator Vacuum Section Based on Transmission Line Code%Dynamic Model for the Z Accelerator Vacuum Section Based on Transmission Line Code

    Institute of Scientific and Technical Information of China (English)

    呼义翔; 雷天时; 吴撼宇; 郭宁; 韩娟娟; 邱爱慈; 王亮平; 黄涛; 丛培天; 张信军; 李岩; 曾正中; 孙铁平

    2011-01-01

    The transmission-line-circuit model of the Z accelerator, developed originally by W. A. STYGAR, P. A. CORCORAN, et al., is revised. The revised model uses different calculations for the electron loss and flow impedance in the magnetically insulated transmission line system of the Z accelerator before and after magnetic insulation is established. By including electron pressure and zero electric field at the cathode, a closed set of equations is obtained at each time step, and dynamic shunt resistance (used to represent any electron loss to the anode) and flow impedance are solved, which have been incorporated into the transmission line code for simulations of the vacuum section in the Z accelerator. Finally, the results are discussed in comparison with earlier findings to show the effectiveness and limitations of the model.

  9. Biomass Resource Allocation among Competing End Uses

    Energy Technology Data Exchange (ETDEWEB)

    Newes, E.; Bush, B.; Inman, D.; Lin, Y.; Mai, T.; Martinez, A.; Mulcahy, D.; Short, W.; Simpkins, T.; Uriarte, C.; Peck, C.

    2012-05-01

    The Biomass Scenario Model (BSM) is a system dynamics model developed by the U.S. Department of Energy as a tool to better understand the interaction of complex policies and their potential effects on the biofuels industry in the United States. However, it does not currently have the capability to account for allocation of biomass resources among the various end uses, which limits its utilization in analysis of policies that target biomass uses outside the biofuels industry. This report provides a more holistic understanding of the dynamics surrounding the allocation of biomass among uses that include traditional use, wood pellet exports, bio-based products and bioproducts, biopower, and biofuels by (1) highlighting the methods used in existing models' treatments of competition for biomass resources; (2) identifying coverage and gaps in industry data regarding the competing end uses; and (3) exploring options for developing models of biomass allocation that could be integrated with the BSM to actively exchange and incorporate relevant information.

  10. A Vehicle Management End-to-End Testing and Analysis Platform for Validation of Mission and Fault Management Algorithms to Reduce Risk for NASAs Space Launch System

    Science.gov (United States)

    Trevino, Luis; Johnson, Stephen B.; Patterson, Jonathan; Teare, David

    2015-01-01

    The engineering development of the National Aeronautics and Space Administration's (NASA) new Space Launch System (SLS) requires cross discipline teams with extensive knowledge of launch vehicle subsystems, information theory, and autonomous algorithms dealing with all operations from pre-launch through on orbit operations. The nominal and off-nominal characteristics of SLS's elements and subsystems must be understood and matched with the autonomous algorithm monitoring and mitigation capabilities for accurate control and response to abnormal conditions throughout all vehicle mission flight phases, including precipitating safing actions and crew aborts. This presents a large and complex systems engineering challenge, which is being addressed in part by focusing on the specific subsystems involved in the handling of off-nominal mission and fault tolerance with response management. Using traditional model-based system and software engineering design principles from the Unified Modeling Language (UML) and Systems Modeling Language (SysML), the Mission and Fault Management (M&FM) algorithms for the vehicle are crafted and vetted in Integrated Development Teams (IDTs) composed of multiple development disciplines such as Systems Engineering (SE), Flight Software (FSW), Safety and Mission Assurance (S&MA) and the major subsystems and vehicle elements such as Main Propulsion Systems (MPS), boosters, avionics, Guidance, Navigation, and Control (GNC), Thrust Vector Control (TVC), and liquid engines. These model-based algorithms and their development lifecycle from inception through FSW certification are an important focus of SLS's development effort to further ensure reliable detection and response to off-nominal vehicle states during all phases of vehicle operation from pre-launch through end of flight. To test and validate these M&FM algorithms a dedicated test-bed was developed for full Vehicle Management End-to-End Testing (VMET). For addressing fault management (FM

  11. End-to-End Security for Personal Telehealth

    NARCIS (Netherlands)

    Koster, R.P.; Asim, M.; Petkovic, M.

    2011-01-01

    Personal telehealth is in rapid development with innovative emerging applications like disease management. With personal telehealth people participate in their own care supported by an open distributed system with health services. This poses new end-to-end security and privacy challenges. In this

  12. 3D simulation of accelerator conventional magnets with end pole defined by an analytical approach controlling multipoles and magnetic length

    CERN Document Server

    Delferrière, O; Duperrier, R

    2000-01-01

    During the design of a magnet, people generally pay particular attention to get the largest transverse section with small contribution of undesirable multipoles, and the 2D cross-section is adjusted in that way with a good accuracy. But the poles are often cut with sharp ends in the beam direction. Otherwise, in order to minimize the stray field to avoid interaction with other elements on the beam lines and corner saturation, it is common to define a simple 45 degrees chamber. The such truncated poles will create an amount of multipoles that could exceed the magnet required tolerances. The magnetic length is also affected by the way that the truncation is done. We propose in this paper a handy analytical model that allows both to control integrated focusing forces and magnetic lengths for each type of conventional magnets (dipole, quadrupole, sextupole). The different end pole profiles are simulated with the 3D-program TOSCA for the dipole and the quadrupole cases. To estimate a possible damaging of optical q...

  13. Data Evaluation of Actinide Cross Sections: 238Pu, 237Pu, and 236Pu

    Energy Technology Data Exchange (ETDEWEB)

    Guaglioni, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jurgenson, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Descalle, M. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Thompson, I. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ormand, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Escher, J. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Younes, W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mattoon, C. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Beck, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Burke, J. T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bailey, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-10-04

    This report documents the recent evaluation of the 236Pu, 237Pu, and 238Pu cross section sets. Nuclear data evaluation is the fundamental interface that takes measured nuclear cross section data and turns them into a continuous curve that 1) is consistent with other measurements and nuclear reaction theory/models, and 2) is required by down-stream users. All experiments that generate nuclear data need to include an evaluation step for their data to be broadly useful to the end users.

  14. Homogenization of linearly anisotropic scattering cross sections in a consistent B1 heterogeneous leakage model

    International Nuclear Information System (INIS)

    Marleau, G.; Debos, E.

    1998-01-01

    One of the main problems encountered in cell calculations is that of spatial homogenization where one associates to an heterogeneous cell an homogeneous set of cross sections. The homogenization process is in fact trivial when a totally reflected cell without leakage is fully homogenized since it involved only a flux-volume weighting of the isotropic cross sections. When anisotropic leakages models are considered, in addition to homogenizing isotropic cross sections, the anisotropic scattering cross section must also be considered. The simple option, which consists of using the same homogenization procedure for both the isotropic and anisotropic components of the scattering cross section, leads to inconsistencies between the homogeneous and homogenized transport equation. Here we will present a method for homogenizing the anisotropic scattering cross sections that will resolve these inconsistencies. (author)

  15. Annual report of the Neutron Physics Section : period ending December 1976

    International Nuclear Information System (INIS)

    Joneja, O.P.; Ramanandham, M.

    1977-01-01

    Research activities of the Neutron Physics Section of the Bhabha Atomic Research Centre, Bombay, for the period July 1975 - December 1976 are reported. Work in the field of : (1) X-ray and neutron crystallography of molecules of biological interest, (2) phase transformations of various kinds and (3) reactor physics and applied neutron physics is being continued. Some of the highlights are : (1) TDC-312 computer controlled neutron diffractometer has been put into operation, (2) two critical configurations using U 233 -uranyl nitrate solution have been planned, (3) vapourisation, melting and other phenomena in rocks as a result of an underground nuclear explosion have been studied. In this connection, computer codes for the propagation of shock waves in rocks using numerical simulation techniques have been developed. (M.G.B.)

  16. Correlates and Predictors of Conflict at the End of Life Among Families Enrolled in Hospice.

    Science.gov (United States)

    Kramer, Betty J; Boelk, Amy Z

    2015-08-01

    Despite the palliative care mandate to view family as the unit of care, and the high prevalence and detrimental consequences of conflict at the end of life, little research has been conducted with hospice families to understand what contributes to family conflict. Using a recently generated explanatory matrix of family conflict at the end of life, this study sought to identify the correlates and predictors of family conflict. As part of a larger mixed methods cross-sectional study, a 100-item survey was administered to 161 hospice family caregivers enrolled in a Medicare/Medicaid certified non-profit hospice organization located in the Midwest U.S. Although overall levels of conflict were relatively low, 57% of hospice caregivers reported experiencing some family conflict at the end of life. Contextual variables associated with family conflict included a history of family conflict, female gender, younger caregiver age, presence of children in the home, and less advance care planning discussions. Significant main effects in the prediction of family conflict in the final hierarchical multiple regression model included prior family conflict, caregiver age, caregiver gender, advance care planning discussions, family "coming out of the woodwork," communication constraints, and family members asserting control. The model explained 59% of the variance in family conflict. Results support the multidimensional theoretical model of family conflict specifying the importance of the family context, key conditions that set the stage for conflict, and essential contributing factors. Implications for routine assessment and screening to identify families at risk and recommendations for future research are highlighted. Copyright © 2015 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All rights reserved.

  17. Lower end fitting debris collector and end cap spacer grid

    International Nuclear Information System (INIS)

    Bryan, W.J.

    1990-01-01

    This patent describes a nuclear reactor having fuel assemblies including an upper end fitting and spaced nuclear fuel rod spacer grids for supporting and spacing a plurality of elongated nuclear fuel rods. Each includes a hollow active portion of nuclear fuel filled cladding intermediate the rod ends and tapering end cap of solid material with a circumferential groove on the rod end which first encounters reactor coolant flow, a lower end filtering debris collector and end cap spacer grid for capturing and retaining deleterious debris carried by reactor coolant before it enters the active region of a fuel assembly and creates fuel rod cladding damage

  18. Optimal cross-sectional sampling for river modelling with bridges: An information theory-based method

    Energy Technology Data Exchange (ETDEWEB)

    Ridolfi, E.; Napolitano, F., E-mail: francesco.napolitano@uniroma1.it [Sapienza Università di Roma, Dipartimento di Ingegneria Civile, Edile e Ambientale (Italy); Alfonso, L. [Hydroinformatics Chair Group, UNESCO-IHE, Delft (Netherlands); Di Baldassarre, G. [Department of Earth Sciences, Program for Air, Water and Landscape Sciences, Uppsala University (Sweden)

    2016-06-08

    The description of river topography has a crucial role in accurate one-dimensional (1D) hydraulic modelling. Specifically, cross-sectional data define the riverbed elevation, the flood-prone area, and thus, the hydraulic behavior of the river. Here, the problem of the optimal cross-sectional spacing is solved through an information theory-based concept. The optimal subset of locations is the one with the maximum information content and the minimum amount of redundancy. The original contribution is the introduction of a methodology to sample river cross sections in the presence of bridges. The approach is tested on the Grosseto River (IT) and is compared to existing guidelines. The results show that the information theory-based approach can support traditional methods to estimate rivers’ cross-sectional spacing.

  19. Optimal cross-sectional sampling for river modelling with bridges: An information theory-based method

    International Nuclear Information System (INIS)

    Ridolfi, E.; Napolitano, F.; Alfonso, L.; Di Baldassarre, G.

    2016-01-01

    The description of river topography has a crucial role in accurate one-dimensional (1D) hydraulic modelling. Specifically, cross-sectional data define the riverbed elevation, the flood-prone area, and thus, the hydraulic behavior of the river. Here, the problem of the optimal cross-sectional spacing is solved through an information theory-based concept. The optimal subset of locations is the one with the maximum information content and the minimum amount of redundancy. The original contribution is the introduction of a methodology to sample river cross sections in the presence of bridges. The approach is tested on the Grosseto River (IT) and is compared to existing guidelines. The results show that the information theory-based approach can support traditional methods to estimate rivers’ cross-sectional spacing.

  20. FLOOD MODELING OF THE VUKA RIVER SECTION UPSTREAM OF ITS CONFLUENCE WITH THE DANUBE RIVER

    Directory of Open Access Journals (Sweden)

    Dario Marić

    2016-12-01

    Full Text Available In this paper, a section of the Vuka River from its confluence with the Danube River in Vukovar to 3 + 630 rkm was modeled. The possibility and size of floods in the surrounding area were analyzed for different return periods (2, 5, 10, 50, and 100 yrs. Although the high-water levels of the Danube River are lower than the terrain elevation of Vukovar, they cause backwater in the Vuka River and in its tributary, the Bobotski canal. In that indirect way, the surrounding area is endangered and the efficiency of drainage systems is reduced. The existing riverbed of the analyzed Vuka River section was digitalized based on a digital terrain model using the geographic information system (GIS software ArcGIS and the HEC-GeoRAS toolbar. A mathematical model of the steady-state flow of the Vuka river section using the digitized riverbed was executed in the HEC-RAS software using different return periods. The obtained velocities and water levels were analyzed using HEC-RAS, and the sizes of the flooded areas were calculated and observed in ArcGIS.

  1. Summary report of the second research co-ordination meeting on improvement of the standard cross sections for light elements

    International Nuclear Information System (INIS)

    Carlson, A.D.; Hale, G.M.; Pronyaev, V.G.

    2004-03-01

    Results are presented following one and a half years of work under the Coordinated Research Project (CRP) on Improvement of the Standard Cross Sections for Light Elements. They include the use of the refined resonating group model for the theoretical prediction of the R-matrix poles and preliminary R-matrix model fits of the full experimental database for the 6 Li+n system obtained with different codes. Significant attention was paid to the exclusion of the bias in the evaluated data caused by the possible presence of Peelle's Pertinent Puzzle effect in the experimental data. Updates were also presented of the experimental database for light and heavy element standards including fission cross sections up to 200 MeV. First results and observed trends for all standard reactions are given, including the preliminary results of combining the model (for light elements) and non-model fits. The timetable for further work was agreed, which should lead to new reaction cross section standards for light and heavy elements by the end 2004. (author)

  2. Failure of Stadard Optical Models to Reproduce Neutron Total Cross Section Difference in the W Isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, J D; Bauer, R W; Dietrich, F S; Grimes, S M; Finlay, R W; Abfalterer, W P; Bateman, F B; Haight, R C; Morgan, G L; Bauge, E; Delaroche, J P; Romain, P

    2001-11-01

    Recently cross section differences among the isotopes{sup 182,184,186}W have been measured as part of a study of total cross sections in the 5-560 MeV energy range. These measurements show oscillations up to 150 mb between 5 and 100 MeV. Spherical and deformed phenomenological optical potentials with typical radial and isospin dependences show very small oscillations, in disagreement with the data. In a simple Ramsauer model, this discrepancy can be traced to a cancellation between radial and isospin effects. Understanding this problem requires a more detailed model that incorporates a realistic description of the neutron and proton density distributions. This has been done with results of Hartree-Fock-Bogolyubov calculations using the Gogny force, together with a microscopic folding model employing a modification of the JLM potential as an effective interaction. This treatment yields a satisfactory interpretation of the observed total cross section differences.

  3. Coincidence cross sections within the quasi free break-up model for elastic projectile break-up

    International Nuclear Information System (INIS)

    Corcalciuc, V.; Jelitto, H.

    1991-11-01

    Scrutinizing the basic break-up model of Serber we show that it is possible to derive the triple differential cross sections for particle-particle coincidences in analytical form. An alternative interpretation within the opaque version of the model suggests to assign these cross sections to the elastic nonresonant projectile break-up due to the nuclear interaction. Distortion effects by the Coulomb field of the target are included in analogy to the Serber model. Beside the well known single maximum in the break-up spectra double and triple peak structures appear for certain combinations of the observation angles. The model yields reasonable agreement to the given experimental data, concerning the multiple peak structure as well as the order of magnitude for the absolute normalisation. Its application comprises the region of forward emission angles, especially the angular range of the classical Coulomb deflection. (orig.) [de

  4. Fission cross-section calculations and the multi-modal fission model

    International Nuclear Information System (INIS)

    Hambsch, F.J.

    2004-01-01

    New, self consistent, neutron-induced reaction cross section calculations for 235,238 U, 237 Np have been performed. The statistical model code STATIS was improved to take into account the multimodality of the fission process. The three most dominant fission modes, the two asymmetric standards I (S1) and standard II (S2) modes and the symmetric superlong (SL) mode have been taken into account. De-convoluted fission cross sections for those modes for 235,238 U(n,f) and 237 Np(n,f) based on experimental branching ratios, were calculated for the first time up to the second chance fission threshold. For 235 U(n,f), the calculations being made up to 28 MeV incident neutron energy, higher fission chances have been considered. This implied the need for additional calculations for the neighbouring isotopes. As a side product also mass yield distributions could be calculated at energies hitherto not accessible by experiment. Experimental validation of the predictions is being envisaged

  5. THE NON-UNIVERSALITY OF THE LOW-MASS END OF THE IMF IS ROBUST AGAINST THE CHOICE OF SSP MODEL

    International Nuclear Information System (INIS)

    Spiniello, C.; Trager, S. C.; Koopmans, L. V. E.

    2015-01-01

    We perform a direct comparison of two state-of-the art single stellar population (SSP) models that have been used to demonstrate the non-universality of the low-mass end of the initial mass function (IMF) slope. The two public versions of the SSP models are restricted to either solar abundance patterns or solar metallicity, too restrictive if one aims to disentangle elemental enhancements, metallicity changes, and IMF variations in massive early-type galaxies (ETGs) with star formation histories different from those in the solar neighborhood. We define response functions (to metallicity and α-abundance) to extend the parameter space for each set of models. We compare these extended models with a sample of Sloan Digital Sky Survey (SDSS) ETG spectra with varying velocity dispersions. We measure equivalent widths of optical IMF-sensitive stellar features to examine the effect of the underlying model assumptions and ingredients, such as stellar libraries or isochrones, on the inference of the IMF slope down to ∼0.1 M ⊙ . We demonstrate that the steepening of the low-mass end of the IMF based on a non-degenerate set of spectroscopic optical indicators is robust against the choice of the stellar population model. Although the models agree in a relative sense (i.e., both imply more bottom-heavy IMFs for more massive systems), we find non-negligible differences in the absolute values of the IMF slope inferred at each velocity dispersion by using the two different models. In particular, we find large inconsistencies in the quantitative predictions of the IMF slope variations and abundance patterns when sodium lines are used. We investigate the possible reasons for these inconsistencies

  6. THE NON-UNIVERSALITY OF THE LOW-MASS END OF THE IMF IS ROBUST AGAINST THE CHOICE OF SSP MODEL

    Energy Technology Data Exchange (ETDEWEB)

    Spiniello, C. [Max-Planck Institute for Astrophysics, Karl-Schwarzschild-Strasse 1, D-8l740 Garching (Germany); Trager, S. C.; Koopmans, L. V. E. [Kapteyn Astronomical Institute, University of Groningen, P.O. Box 800, 9700 AV Groningen (Netherlands)

    2015-04-20

    We perform a direct comparison of two state-of-the art single stellar population (SSP) models that have been used to demonstrate the non-universality of the low-mass end of the initial mass function (IMF) slope. The two public versions of the SSP models are restricted to either solar abundance patterns or solar metallicity, too restrictive if one aims to disentangle elemental enhancements, metallicity changes, and IMF variations in massive early-type galaxies (ETGs) with star formation histories different from those in the solar neighborhood. We define response functions (to metallicity and α-abundance) to extend the parameter space for each set of models. We compare these extended models with a sample of Sloan Digital Sky Survey (SDSS) ETG spectra with varying velocity dispersions. We measure equivalent widths of optical IMF-sensitive stellar features to examine the effect of the underlying model assumptions and ingredients, such as stellar libraries or isochrones, on the inference of the IMF slope down to ∼0.1 M{sub ⊙}. We demonstrate that the steepening of the low-mass end of the IMF based on a non-degenerate set of spectroscopic optical indicators is robust against the choice of the stellar population model. Although the models agree in a relative sense (i.e., both imply more bottom-heavy IMFs for more massive systems), we find non-negligible differences in the absolute values of the IMF slope inferred at each velocity dispersion by using the two different models. In particular, we find large inconsistencies in the quantitative predictions of the IMF slope variations and abundance patterns when sodium lines are used. We investigate the possible reasons for these inconsistencies.

  7. Compression and flexural properties of finger jointed mango wood sections

    OpenAIRE

    Kumar, V.S Kishan; Sharma, C.M; Gupta, Sachin

    2014-01-01

    In this paper, an attempt was made to assess the effectiveness of finger jointing in utilising mango wood sections for various end uses like furniture. The study was based on the estimation of Modulus of elasticity and Modulus of rupture under static bending and Maximum Crushing Stress and Modulus of elasticity under compression parallel to grain of finger jointed sections and comparing them with the values measured for clear wood sections from the same lot. For joining the sections, the Poly...

  8. The Mechanics of a Cantilever Beam with an Embedded Horizontal Crack Subjected to an End Transverse Force, Part A: Modelling

    Directory of Open Access Journals (Sweden)

    Panos G. Charalambides

    2016-05-01

    Full Text Available This study addresses the mechanics of a cracked cantilever beam subjected to a transverse force applied at it’s free end. In this Part A of a two Part series of papers, emphasis is placed on the development of a four-beam model for a beam with a fully embedded horizontal sharp crack. The beam aspect ratio, crack length and crack centre location appear as general model parameters. Rotary springs are introduced at the crack tip cross sections as needed to account for the changes in the structural compliance due to the presence of the sharp crack and augmented load transfer through the near-tip transition regions. Guided by recent finite element findings reported elsewhere, the four-beam model is advanced by recognizing two key observations, (a the free surface and neutral axis curvatures of the cracked beam at the crack center location match the curvature of a healthy beam (an identical beam without a crack under the same loading conditions, (b the neutral axis rotations (slope of the cracked beam in the region between the applied load and the nearest crack tip matches the corresponding slope of the healthy beam. The above observations led to the development of close form solutions for the resultant forces (axial and shear and moment acting in the beams above and below the crack. Axial force and bending moment predictions are found to be in excellent agreement with 2D finite element results for all normalized crack depths considered. Shear force estimates dominating the beams above and below the crack as well as transition region length estimates are also obtained. The model developed in this study is then used along with 2D finite elements in conducting parametric studies aimed at both validating the model and establishing the mechanics of the cracked system under consideration. The latter studies are reported in the companion paper Part B-Results and Discussion.

  9. Large Psub(tr) and quark-quark cross section in the dynamical model of factorizing quarks

    International Nuclear Information System (INIS)

    Kapshay, V.N.; Sidorov, A.V.; Skachkov, N.B.

    1978-01-01

    Dynamical model of factorizing quarks containing the quark mass as free model parameter was described. Model calculations were compared with the experimental data on the cross section of the inclusive πsup(o) meson production in the proton-proton interaction. It is shown that the results of the paper are in good agreement with experiments

  10. Application of an enhanced cross-section interpolation model for highly poisoned LWR core calculations

    International Nuclear Information System (INIS)

    Palau, J.M.; Cathalau, S.; Hudelot, J.P.; Barran, F.; Bellanger, V.; Magnaud, C.; Moreau, F.

    2011-01-01

    Burnable poisons are extensively used by Light Water Reactor designers in order to preserve the fuel reactivity potential and increase the cycle length (without increasing the uranium enrichment). In the industrial two-steps (assembly 2D transport-core 3D diffusion) calculation schemes these heterogeneities yield to strong flux and cross-sections perturbations that have to be taken into account in the final 3D burn-up calculations. This paper presents the application of an enhanced cross-section interpolation model (implemented in the French CRONOS2 code) to LWR (highly poisoned) depleted core calculations. The principle is to use the absorbers (or actinide) concentrations as the new interpolation parameters instead of the standard local burnup/fluence parameters. It is shown by comparing the standard (burnup/fluence) and new (concentration) interpolation models and using the lattice transport code APOLLO2 as a numerical reference that reactivity and local reaction rate prediction of a 2x2 LWR assembly configuration (slab geometry) is significantly improved with the concentration interpolation model. Gains on reactivity and local power predictions (resp. more than 1000 pcm and 20 % discrepancy reduction compared to the reference APOLLO2 scheme) are obtained by using this model. In particular, when epithermal absorbers are inserted close to thermal poison the 'shadowing' ('screening') spectral effects occurring during control operations are much more correctly modeled by concentration parameters. Through this outstanding example it is highlighted that attention has to be paid to the choice of cross-section interpolation parameters (burnup 'indicator') in core calculations with few energy groups and variable geometries all along the irradiation cycle. Actually, this new model could be advantageously applied to steady-state and transient LWR heterogeneous core computational analysis dealing with strong spectral-history variations under

  11. Weighted-DESYNC and Its Application to End-to-End Throughput Fairness in Wireless Multihop Network

    Directory of Open Access Journals (Sweden)

    Ui-Seong Yu

    2017-01-01

    Full Text Available The end-to-end throughput of a routing path in wireless multihop network is restricted by a bottleneck node that has the smallest bandwidth among the nodes on the routing path. In this study, we propose a method for resolving the bottleneck-node problem in multihop networks, which is based on multihop DESYNC (MH-DESYNC algorithm that is a bioinspired resource allocation method developed for use in multihop environments and enables fair resource allocation among nearby (up to two hops neighbors. Based on MH-DESYNC, we newly propose weighted-DESYNC (W-DESYNC as a tool artificially to control the amount of resource allocated to the specific user and thus to achieve throughput fairness over a routing path. Proposed W-DESYNC employs the weight factor of a link to determine the amount of bandwidth allocated to a node. By letting the weight factor be the link quality of a routing path and making it the same across a routing path via Cucker-Smale flocking model, we can obtain throughput fairness over a routing path. The simulation results show that the proposed algorithm achieves throughput fairness over a routing path and can increase total end-to-end throughput in wireless multihop networks.

  12. Unobserved Heterogeneity in the Binary Logit Model with Cross-Sectional Data and Short Panels

    DEFF Research Database (Denmark)

    Holm, Anders; Jæger, Mads Meier; Pedersen, Morten

    This paper proposes a new approach to dealing with unobserved heterogeneity in applied research using the binary logit model with cross-sectional data and short panels. Unobserved heterogeneity is particularly important in non-linear regression models such as the binary logit model because, unlike...... in linear regression models, estimates of the effects of observed independent variables are biased even when omitted independent variables are uncorrelated with the observed independent variables. We propose an extension of the binary logit model based on a finite mixture approach in which we conceptualize...

  13. How to Use Benchmark and Cross-section Studies to Improve Data Libraries and Models

    Science.gov (United States)

    Wagner, V.; Suchopár, M.; Vrzalová, J.; Chudoba, P.; Svoboda, O.; Tichý, P.; Krása, A.; Majerle, M.; Kugler, A.; Adam, J.; Baldin, A.; Furman, W.; Kadykov, M.; Solnyshkin, A.; Tsoupko-Sitnikov, S.; Tyutyunikov, S.; Vladimirovna, N.; Závorka, L.

    2016-06-01

    Improvements of the Monte Carlo transport codes and cross-section libraries are very important steps towards usage of the accelerator-driven transmutation systems. We have conducted a lot of benchmark experiments with different set-ups consisting of lead, natural uranium and moderator irradiated by relativistic protons and deuterons within framework of the collaboration “Energy and Transmutation of Radioactive Waste”. Unfortunately, the knowledge of the total or partial cross-sections of important reactions is insufficient. Due to this reason we have started extensive studies of different reaction cross-sections. We measure cross-sections of important neutron reactions by means of the quasi-monoenergetic neutron sources based on the cyclotrons at Nuclear Physics Institute in Řež and at The Svedberg Laboratory in Uppsala. Measurements of partial cross-sections of relativistic deuteron reactions were the second direction of our studies. The new results obtained during last years will be shown. Possible use of these data for improvement of libraries, models and benchmark studies will be discussed.

  14. 20 CFR 404.337 - When does my entitlement to widow's and widower's benefits start and end?

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false When does my entitlement to widow's and widower's benefits start and end? 404.337 Section 404.337 Employees' Benefits SOCIAL SECURITY... does my entitlement to widow's and widower's benefits start and end? (a) We will find you entitled to...

  15. Environmental Sciences Division. Annual progress report for period ending September 30, 1979

    International Nuclear Information System (INIS)

    1980-03-01

    Progress for the period ending September 30, 1979 by the Environmental Sciences Division is reported. Sections reporting include terrestrial ecoloy; earth sciences; environmental resources; aquatic ecology; synthetic fuels; nuclear program; environmental impacts program; ecosystem studies; and burial ground technology

  16. MDT-ASD, CMOS front-end for ATLAS MDT

    CERN Document Server

    Posch, C; Oliver, J

    2007-01-01

    This document serves as the main reference and user`s manual for the read-out chip of the Monitored Drift Tubes in the ATLAS Muon Spectrometer. The eight-channel front-end ASIC is referred to as MDT-ASD. The document contains the requirements and complete specifications, a detailed description of the design with characteristics of all sub-circuits and building blocks, a comprehensive section on functionality and performance test results, and a complete bibliography.

  17. Analysis on learning curves of end-use appliances for the establishment of price-sensitivity load model in competitive electricity market

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Sung Wook; Kim, Jung Hoon [Hongik University (Korea); Song, Kyung Bin [Keimyung University (Korea); Choi, Joon Young [Jeonju University (Korea)

    2001-07-01

    The change of the electricity charge from cost base to price base due to the introduction to the electricity market competition causes consumer to choose a variety of charge schemes and a portion of loads to be affected by this change. Besides, it is required the index that consolidate the price volatility experienced on the power exchange with gaming and strategic bidding by suppliers to increase profits. Therefore, in order to find a mathematical model of the sensitively-responding to-price loads, the price-sensitive load model is needed. And the development of state-of- the-art technologies affects the electricity price, so the diffusion of high-efficient end-uses and these price affect load patterns. This paper shows the analysis on learning curves algorithms which is used to investigate the correlation of the end-uses' price and load patterns. (author). 6 refs., 4 figs., 4 tabs.

  18. Spectral investigation of neutron radiation in three-sectional concrete labyrinth from a californium-252 source

    International Nuclear Information System (INIS)

    Belogorlov, E.A.; Britvich, G.I.; Getmanov, V.B.

    1985-01-01

    Construction of labyrinths in points of communication output from the storage-ring under construction is accompanied by numerous difficulties due to a considerable number of gas and cryogenic pipelines, which require large cross sections at the minimal length of the pipelines proper for their location. It results in unfavourable for radiation attenuation ratios between cross section and length of the labyrinth separate sections. Neutron spectra in a model concrete labyrinth, at the entrance to which a neutron source with fission spectrum (californium-252) and the same source in a polyethylene moderator are located, are measured. On the basis of the spectra obtained the formation of fluence and equivalent dose along the labyrinth geometric axis is analyzed. Conditions permitting actually to reduce radiation dose in the labyrinth (dead end provision, the use of cover materials, construction of diaphragms and shielding plates) are simulated

  19. Comparison of Direct Side-to-End and End-to-End Hypoglossal-Facial Anastomosis for Facial Nerve Repair.

    Science.gov (United States)

    Samii, Madjid; Alimohamadi, Maysam; Khouzani, Reza Karimi; Rashid, Masoud Rafizadeh; Gerganov, Venelin

    2015-08-01

    The hypoglossal facial anastomosis (HFA) is the gold standard for facial reanimation in patients with severe facial nerve palsy. The major drawbacks of the classic HFA technique are lingual morbidities due to hypoglossal nerve transection. The side-to-end HFA is a modification of the classic technique with fewer tongue-related morbidities. In this study we compared the outcome of the classic end-to-end and the direct side-to-end HFA surgeries performed at our center in regards to the facial reanimation success rate and tongue-related morbidities. Twenty-six successive cases of HFA were enrolled. In 9 of them end-to-end anastomoses were performed, and 17 had direct side-to-end anastomoses. The House-Brackmann (HB) and Pitty and Tator (PT) scales were used to document surgical outcome. The hemiglossal atrophy, swallowing, and hypoglossal nerve function were assessed at follow-up. The original pathology was vestibular schwannoma in 15, meningioma in 4, brain stem glioma in 4, and other pathologies in 3. The mean interval between facial palsy and HFA was 18 months (range: 0-60). The median follow-up period was 20 months. The PT grade at follow-up was worse in patients with a longer interval from facial palsy and HFA (P value: 0.041). The lesion type was the only other factor that affected PT grade (the best results in vestibular schwannoma and the worst in the other pathologies group, P value: 0.038). The recovery period for facial tonicity was longer in patients with radiation therapy before HFA (13.5 vs. 8.5 months) and those with a longer than 2-year interval from facial palsy to HFA (13.5 vs. 8.5 months). Although no significant difference between the side-to-end and the end-to-end groups was seen in terms of facial nerve functional recovery, patients from the side-to-end group had a significantly lower rate of lingual morbidities (tongue hemiatrophy: 100% vs. 5.8%, swallowing difficulty: 55% vs. 11.7%, speech disorder 33% vs. 0%). With the side-to-end HFA

  20. Reconstitutable control assembly having removable control rods with detachable split upper end plugs

    International Nuclear Information System (INIS)

    Gjertsen, R.K.; Knott, R.P.; Sparrow, J.A.

    1991-01-01

    This patent describes, for use in facilitating replacement of a neutron absorber control rod on a control assembly spider structure, an end plug. It comprises a pair of separate upper and lower plug portions; the upper section of the upper plug portion being configured for rigid attachment; the middle section of the upper plug portion having angularly displaced flat surfaces formed on the exterior

  1. Workshop on electronic and ionic collision cross sections needed in the modeling of radiation interactions with matter: proceedings

    International Nuclear Information System (INIS)

    1984-05-01

    The term modeling in the Workship title refers to the mathematical analysis of the consequences of many collision processes for characterizing the physical stage of radiation actions. It requires as input some knowledge of collision cross sections. Traditionally, work on cross sections and work on the modeling are conducted by separate groups of scientists. It was the purpose of the Workshop to bring these two groups together in a forum that would promote effective communication. Cross-section workers described the status of their work and told what data were available or trustworthy. Modeling workers told what kind of data were needed or were most important. Twenty-two items from the workshop were prepared separately for the data base

  2. Workshop on electronic and ionic collision cross sections needed in the modeling of radiation interactions with matter: proceedings

    Energy Technology Data Exchange (ETDEWEB)

    1984-05-01

    The term modeling in the Workship title refers to the mathematical analysis of the consequences of many collision processes for characterizing the physical stage of radiation actions. It requires as input some knowledge of collision cross sections. Traditionally, work on cross sections and work on the modeling are conducted by separate groups of scientists. It was the purpose of the Workshop to bring these two groups together in a forum that would promote effective communication. Cross-section workers described the status of their work and told what data were available or trustworthy. Modeling workers told what kind of data were needed or were most important. Twenty-two items from the workshop were prepared separately for the data base.

  3. A Computer Model for the Hydraulic Analysis of Open Channel Cross Sections

    Directory of Open Access Journals (Sweden)

    W. H. Shayya

    1996-01-01

    Full Text Available Irrigation and hydraulic engineers are often faced with the difficulty of tedious trial solutions of the Manning equation to determine the various geometric elements of open channels. This paper addresses the development of a computer model for the design of the most commonly used channel-sections. The developed model is intended as an educational tool. It may be applied to the hydraulic design of trapezoidal , rectangular, triangular, parabolic, round-concered rectangular, and circular cross sections. Two procedures were utilized for the solution of the encountered implicit equations; the Newton-Raphson and the Regula-Falsi methods.  In order to initiate the solution process , these methods require one and two initial guesses, respectively. Tge result revealed that the Regula-Flasi method required more iterations to coverage to the solution compared to the Newton-Raphson method, irrespective of the nearness of the initial guess to the actual solution. The average number of iterations for the Regula-Falsi method was approximately three times that of the Newton-Raphson method.

  4. Magnet Misalignment Studies for the Front-end of the Neutrino Factory

    CERN Document Server

    Prior, G; Stratakis, D; Neuffer, D; Snopok, P; Rogers, C

    2013-01-01

    In the Neutrino Factory front-end the muon beam coming from the interaction of a high-power (4 MW) proton beam on a mercury jet target is transformed through a buncher, a phase rotator and an ionization cooling channel before entering the downstream acceleration system. The muon front-end channel is densely packed with solenoid magnets, normal conducting radio-frequency cavities and absorber windows for the cooling section. The tolerance to the misalignment of the different components has to be determined in order on one hand to set the limits beyond which the performance of the front-end channel would be degraded; on the other hand to optimize the design and assembly of the front-end cells such that the component alignment can be checked and corrected for where crucial for the performance of the channel. In this paper we show the results of some of the simulations of the frontend channel performance where the magnetic field direction has been altered compared to the baseline.

  5. Modal Bin Hybrid Model: A surface area consistent, triple-moment sectional method for use in process-oriented modeling of atmospheric aerosols

    Science.gov (United States)

    Kajino, Mizuo; Easter, Richard C.; Ghan, Steven J.

    2013-09-01

    triple-moment sectional (TMS) aerosol dynamics model, Modal Bin Hybrid Model (MBHM), has been developed. In addition to number and mass (volume), surface area is predicted (and preserved), which is important for aerosol processes and properties such as gas-to-particle mass transfer, heterogeneous reaction, and light extinction cross section. The performance of MBHM was evaluated against double-moment sectional (DMS) models with coarse (BIN4) to very fine (BIN256) size resolutions for simulating evolution of particles under simultaneously occurring nucleation, condensation, and coagulation processes (BINx resolution uses x sections to cover the 1 nm to 1 µm size range). Because MBHM gives a physically consistent form of the intrasectional distributions, errors and biases of MBHM at BIN4-8 resolution were almost equivalent to those of DMS at BIN16-32 resolution for various important variables such as the moments Mk (k: 0, 2, 3), dMk/dt, and the number and volume of particles larger than a certain diameter. Another important feature of MBHM is that only a single bin is adequate to simulate full aerosol dynamics for particles whose size distribution can be approximated by a single lognormal mode. This flexibility is useful for process-oriented (multicategory and/or mixing state) modeling: Primary aerosols whose size parameters would not differ substantially in time and space can be expressed by a single or a small number of modes, whereas secondary aerosols whose size changes drastically from 1 to several hundred nanometers can be expressed by a number of modes. Added dimensions can be applied to MBHM to represent mixing state or photochemical age for aerosol mixing state studies.

  6. ROXIE: Routine for the optimization of magnet X-sections, inverse field calculation and coil end design. Proceedings

    International Nuclear Information System (INIS)

    Russenschuck, S.

    1999-01-01

    The Large Hadron Collider (LHC) will provide proton-proton collisions with a center-of-mass energy of 14 TeV which requires high field superconducting magnets to guide the counter-rotating beams in the existing LEP tunnel with a circumference of about 27 km. The LHC magnet system consists of 1232 superconducting dipoles and 386 main quadrupoles together with about 20 different types of magnets for insertions and correction. The design and optimization of these magnets is dominated by the requirement of a extremely uniform field which is mainly defined by the layout of the superconducting coils. The program package ROXIE (Routine for the Optimization of magnet X-sections, Inverse field calculation and coil End design) has been developed for the design and optimization of the coil geometries in two and three dimensions. Recently it has been extended in a collaboration with the University of Graz, Austria, to the calculation of saturation induced effects using a reduced vector-potential FEM formulation. With the University of Stuttgart, Germany, a collaboration exists fro the application of the BEM-FEM coupling method for the 2D and 3D field calculation. ROXIE now also features a TCL-TK user interface. The growing number of ROXIE users inside and outside CERN gave rise to the idea of organizing the 'First International ROXIE Users Meeting and Workshop' at CERN, March 16-18, 1998 which brought together about 50 researchers in the field. This report contains the contributions to the workshop and describes the features of the program, the mathematical optimization techniques applied and gives examples of the recent design work carried out. It also gives the theoretical background for the field computation methods and serves as a handbook for the installation and application of the program. (orig.)

  7. ROXIE: Routine for the optimization of magnet X-sections, inverse field calculation and coil end design. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Russenschuck, S [ed.

    1999-04-12

    The Large Hadron Collider (LHC) will provide proton-proton collisions with a center-of-mass energy of 14 TeV which requires high field superconducting magnets to guide the counter-rotating beams in the existing LEP tunnel with a circumference of about 27 km. The LHC magnet system consists of 1232 superconducting dipoles and 386 main quadrupoles together with about 20 different types of magnets for insertions and correction. The design and optimization of these magnets is dominated by the requirement of a extremely uniform field which is mainly defined by the layout of the superconducting coils. The program package ROXIE (Routine for the Optimization of magnet X-sections, Inverse field calculation and coil End design) has been developed for the design and optimization of the coil geometries in two and three dimensions. Recently it has been extended in a collaboration with the University of Graz, Austria, to the calculation of saturation induced effects using a reduced vector-potential FEM formulation. With the University of Stuttgart, Germany, a collaboration exists fro the application of the BEM-FEM coupling method for the 2D and 3D field calculation. ROXIE now also features a TCL-TK user interface. The growing number of ROXIE users inside and outside CERN gave rise to the idea of organizing the 'First International ROXIE Users Meeting and Workshop' at CERN, March 16-18, 1998 which brought together about 50 researchers in the field. This report contains the contributions to the workshop and describes the features of the program, the mathematical optimization techniques applied and gives examples of the recent design work carried out. It also gives the theoretical background for the field computation methods and serves as a handbook for the installation and application of the program. (orig.)

  8. Fault-related-folding structure and reflection seismic sections. Construction of earth model using balanced cross section; Danso ga kaizaisuru shukyoku kozo no keitai to jishin tansa danmen. 1. Balanced cross section wo mochiita chika model no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Tamagawa, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    Pre-stacking depth migration treatment is studied for the estimation of the fold configuration from seismic survey cross sections. The estimation of a velocity structure is necessary for the execution of such treatment, and the utilization of structural-geological knowledge is required for its interpretation. The concept of balanced cross section in relation to the fault-bend fold constructs a stratum structure model under conditions that the deformation during fold and fault formation is a planar strain, that there is no change in volume due to deformation, and that a fold is a parallel fold. In addition to the above geometric and kinetic approach, there is another fold formation process simulation model using a Newtonian fluid for study from the viewpoint of dynamics. This simulation stands on the presumption that the boundary contains a ramp that had been in presence before fold formation and that an incompressible viscous matter is mounted on the top surface. The viscous matter flows and deforms for the formation of an anticline on the ramp. Such enables the reproduction of a fault-bend fold formation process, and helpful discussion may be furthered on the dynamic aspect of this simulation. 5 refs., 4 figs.

  9. Modeling end-use quality in U. S. soft wheat germplasm

    Science.gov (United States)

    End-use quality in soft wheat (Triticum aestivum L.) can be assessed by a wide array of measurements, generally categorized into grain, milling, and baking characteristics. Samples were obtained from four regional nurseries. Selected parameters included: test weight, kernel hardness, kernel size, ke...

  10. Residential applliance data, assumptions and methodology for end-use forecasting with EPRI-REEPS 2.1

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, R.J,; Johnson, F.X.; Brown, R.E.; Hanford, J.W.; Kommey, J.G.

    1994-05-01

    This report details the data, assumptions and methodology for end-use forecasting of appliance energy use in the US residential sector. Our analysis uses the modeling framework provided by the Appliance Model in the Residential End-Use Energy Planning System (REEPS), which was developed by the Electric Power Research Institute. In this modeling framework, appliances include essentially all residential end-uses other than space conditioning end-uses. We have defined a distinct appliance model for each end-use based on a common modeling framework provided in the REEPS software. This report details our development of the following appliance models: refrigerator, freezer, dryer, water heater, clothes washer, dishwasher, lighting, cooking and miscellaneous. Taken together, appliances account for approximately 70% of electricity consumption and 30% of natural gas consumption in the US residential sector. Appliances are thus important to those residential sector policies or programs aimed at improving the efficiency of electricity and natural gas consumption. This report is primarily methodological in nature, taking the reader through the entire process of developing the baseline for residential appliance end-uses. Analysis steps documented in this report include: gathering technology and market data for each appliance end-use and specific technologies within those end-uses, developing cost data for the various technologies, and specifying decision models to forecast future purchase decisions by households. Our implementation of the REEPS 2.1 modeling framework draws on the extensive technology, cost and market data assembled by LBL for the purpose of analyzing federal energy conservation standards. The resulting residential appliance forecasting model offers a flexible and accurate tool for analyzing the effect of policies at the national level.

  11. MODELING AND ANALYSIS OF COUPLED FLEXURAL-TORSIONAL SPINNING BEAMS WITH UNSYMMETRICAL CROSS SECTIONS

    OpenAIRE

    Wang, Jie; Li, Dongxu; Jiang, Jianping

    2017-01-01

    The structural modeling and dynamic properties of a spinning beam with an unsymmetrical cross section are studied. Due to the eccentricity and spinning, transverse deflections along the two principal directions and the torsional motion about the longitudinal axis are coupled. The structural model of the beam is established based on the Hamilton principle and by incorporating the torsional inertia. Moreover, because of its significant influence on characteristics for the non-circular cross-sec...

  12. Assessing End-Of-Supply Risk of Spare Parts Using the Proportional Hazard Model

    NARCIS (Netherlands)

    X. Li (Xishu); R. Dekker (Rommert); C. Heij (Christiaan); M. Hekimoğlu (Mustafa)

    2016-01-01

    textabstractOperators of long field-life systems like airplanes are faced with hazards in the supply of spare parts. If the original manufacturers or suppliers of parts end their supply, this may have large impacts on operating costs of firms needing these parts. Existing end-of-supply evaluation

  13. The Effect of Modeling and Visualization Resources on Student Understanding of Physical Hydrology

    Science.gov (United States)

    Marshall, Jilll A.; Castillo, Adam J.; Cardenas, M. Bayani

    2015-01-01

    We investigated the effect of modeling and visualization resources on upper-division, undergraduate and graduate students' performance on an open-ended assessment of their understanding of physical hydrology. The students were enrolled in one of five sections of a physical hydrology course. In two of the sections, students completed homework…

  14. Fourier method for modeling slanted lamellar gratings of arbitrary end-surface shapes in conical mounting.

    Science.gov (United States)

    Li, Lifeng

    2015-10-01

    An efficient modal method for numerically modeling slanted lamellar gratings of isotropic dielectric or metallic media in conical mounting is presented. No restrictions are imposed on the slant angle and the length of the lamellae. The end surface of the lamellae can be arbitrary, subject to certain restrictions. An oblique coordinate system that is adapted to the slanted lamella sidewalls allows the most efficient way of representing and manipulating the electromagnetic fields. A translational coordinate system that is based on the oblique Cartesian coordinate system adapts to the end-surface profile of the lamellae, so that the latter can be handled simply and easily. Moreover, two matrix eigenvalue problems of size 2N × 2N, one for each fundamental polarization of the electromagnetic fields in the periodic lamellar structure, where N is the matrix truncation number, are derived to replace the 4N × 4N eigenvalue problem that has been used in the literature. The core idea leading to this success is the polarization decomposition of the electromagnetic fields inside the periodic lamellar region when the fields are expressed in the oblique translational coordinate system.

  15. Riddles of the Sphinx: Titan Science Questions at the End of Cassini-Huygens

    Science.gov (United States)

    Nixon, C. A.; Achterberg, R. K.; Buch, A.; Clark, R. N.; Coll, P.; Flasar, F. M.; Hayes, A. G.; Iess, L.; Lorenz, R. D.; Lopes, R.; Mastroguiseppe, M.; Raulin, F.; Smith, T.; Solomidou, A.; Sotin, C.; Strobel, D. F.; Turtle, E. P.; Vuitton, V.; West, R. A.; Yelle, R.

    2017-02-01

    The paper will describe the outstanding high-level questions for Titan science that are remaining at the end of the Cassini-Huygens mission, compiled by a cross-section of scientists from multiple instrument teams.

  16. Study of p-4He Total Reaction cross section using Glauber and Modified Glauber Models

    International Nuclear Information System (INIS)

    Tag El Din, I.M.A.; Taha, M.M.; Hassan, S.S.A.

    2012-01-01

    The total nuclear reaction cross-section for p - 4 He in the energy range from 25 to 1000 MeV is calculated within Glauber and modified Glauber models. The modified Glauber model is introduced via both Coulomb trajectory of the projectile and calculation of the effective radius of interaction. The effects of density dependent total cross-section and phase variation of nucleon-nucleon scattering amplitude are studied. It is pointed out that the phase variation of the nucleon-nucleon amplitude plays a significant role in describing σR at E p 2 at e = e0 = 0 and γ=2fm 2 at e = e0 = 0.17fm -3 .

  17. Influence of horizontally curved roadway section characteristics on motorcycle-to-barrier crash frequency.

    Science.gov (United States)

    Gabauer, Douglas J; Li, Xiaolong

    2015-04-01

    The purpose of this study was to investigate motorcycle-to-barrier crash frequency on horizontally curved roadway sections in Washington State using police-reported crash data linked with roadway data and augmented with barrier presence information. Data included 4915 horizontal curved roadway sections with 252 of these sections experiencing 329 motorcycle-to-barrier crashes between 2002 and 2011. Negative binomial regression was used to predict motorcycle-to-barrier crash frequency using horizontal curvature and other roadway characteristics. Based on the model results, the strongest predictor of crash frequency was found to be curve radius. This supports a motorcycle-to-barrier crash countermeasure placement criterion based, at the very least, on horizontal curve radius. With respect to the existing horizontal curve criterion of 820 feet or less, curves meeting this criterion were found to increase motorcycle-to-barrier crash frequency rate by a factor of 10 compared to curves not meeting this criterion. Other statistically significant predictors were curve length, traffic volume and the location of adjacent curves. Assuming curves of identical radius, the model results suggest that longer curves, those with higher traffic volume, and those that have no adjacent curved sections within 300 feet of either curve end would likely be better candidates for a motorcycle-to-barrier crash countermeasure. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Observations on dual-ended readout of 100 mm long LYSO crystals

    Energy Technology Data Exchange (ETDEWEB)

    Ur-Rehman, Fazal, E-mail: Fazal@physics.umanitoba.ca [Department of Physics and Astronomy, University of Manitoba, Winnipeg (Canada); McIntosh, Bryan [Department of Physics and Astronomy, University of Manitoba, Winnipeg (Canada); Goertzen, Andrew L. [Department of Physics and Astronomy, University of Manitoba, Winnipeg (Canada); Department of Radiology, University of Manitoba, Winnipeg (Canada)

    2011-10-01

    We are investigating using dual-ended readout of axially oriented long thin scintillator crystals in detectors for a compact geometry, small ring diameter animal PET system. The axial position of interaction is determined from the light sharing between two photodetectors at opposite ends of the crystal. We examine the light output, energy resolution and axial spatial resolution of 1.5-5x2x100 mm{sup 3} polished LYSO crystals by irradiating with an electronically collimated beam of 511 keV photons oriented perpendicular to the long axis and read out at either end by position sensitive photomultiplier tubes (PSPMTs). Three reflector materials, namely Teflon, 3 M enhanced specular reflector (ESR) and black paint are examined for the 2x2x100 mm{sup 3} crystal size. The light output increases and energy resolution improves with the crystal cross-section. Generally, the spatial resolution worsens with increase in crystal cross-section. For the 2x2x100 mm{sup 3} crystal size, the mean energy resolutions of the photopeak over the nine irradiation positions were 14.4{+-}0.4%, 16.0{+-}1.2% and 28.3{+-}2.1% with mean spatial resolutions of 7.0{+-}1.0, 9.4{+-}3.3 and 26.0{+-}5.0 mm using ESR, Teflon and black paint, respectively. ESR reflector gave the best light output, energy and axial spatial resolutions. These characterization results of PSPMT-based dual-ended long LYSO crystals will be useful in the design of detector modules for a highly compact geometry preclinical PET system using this detector technology.

  19. Multi-institutional evaluation of end-to-end protocol for IMRT/VMAT treatment chains utilizing conventional linacs.

    Science.gov (United States)

    Loughery, Brian; Knill, Cory; Silverstein, Evan; Zakjevskii, Viatcheslav; Masi, Kathryn; Covington, Elizabeth; Snyder, Karen; Song, Kwang; Snyder, Michael

    2018-03-20

    We conducted a multi-institutional assessment of a recently developed end-to-end monthly quality assurance (QA) protocol for external beam radiation therapy treatment chains. This protocol validates the entire treatment chain against a baseline to detect the presence of complex errors not easily found in standard component-based QA methods. Participating physicists from 3 institutions ran the end-to-end protocol on treatment chains that include Imaging and Radiation Oncology Core (IROC)-credentialed linacs. Results were analyzed in the form of American Association of Physicists in Medicine (AAPM) Task Group (TG)-119 so that they may be referenced by future test participants. Optically stimulated luminescent dosimeter (OSLD), EBT3 radiochromic film, and A1SL ion chamber readings were accumulated across 10 test runs. Confidence limits were calculated to determine where 95% of measurements should fall. From calculated confidence limits, 95% of measurements should be within 5% error for OSLDs, 4% error for ionization chambers, and 4% error for (96% relative gamma pass rate) radiochromic film at 3% agreement/3 mm distance to agreement. Data were separated by institution, model of linac, and treatment protocol (intensity-modulated radiation therapy [IMRT] vs volumetric modulated arc therapy [VMAT]). A total of 97% of OSLDs, 98% of ion chambers, and 93% of films were within the confidence limits; measurements were found outside these limits by a maximum of 4%, consistent despite institutional differences in OSLD reading equipment and radiochromic film calibration techniques. Results from this test may be used by clinics for data comparison. Areas of improvement were identified in the end-to-end protocol that can be implemented in an updated version. The consistency of our data demonstrates the reproducibility and ease-of-use of such tests and suggests a potential role for their use in broad end-to-end QA initiatives. Copyright © 2018 American Association of Medical

  20. End-of-life care: Indian perspective

    Science.gov (United States)

    Sharma, Himanshu; Jagdish, Vankar; Anusha, Prabhakaran; Bharti, Sharma

    2013-01-01

    According to Hinduism, the main religion of India, the end-of-life (EOL) deals with good and bad death. The WHO definition of palliative care stresses on improving not only the quality of life of patients facing incurable diseases but also their families by providing relief from the pain and suffering that includes the psychosocial and spiritual needs as well. The Indian Society of Palliative Care has been doing a commendable work and appreciable efforts are being done by the Kerala model of delivering the EOL care. The spiritual, ethical issues and ethical challenges raised when the patients are in terminal phase are also reviewed keeping in mind the socio-cultural norms. The Indian Penal Code (IPC) has lacunae, which hamper the physicians from taking proper decision in the EOL care. Some of the sections like IPC 309 are defunct and need to be changed. The Indian Society for Critical Care Medicine has developed a position statement on the patient management of the terminally ill patient in the Intensive Care Unit (ICU) which states that the society should move from the paternalistic model to the share based decision model of the West when deciding the fate of such patients. The literature review on the Indian research on palliative care shows very little emphatic results and the medical under graduates show illiteracy. To strengthen it Medical Council of India has included the palliative care in its curriculum by starting a PG course. Literature review revealed that more research from Indian perspective should be done in this area. This article studies the core issues of developing palliative care in Indian setting keeping in mind the ethical, spiritual and legal issues. PMID:23858271

  1. Estimation of contribution ratios of pollutant sources to a specific section based on an enhanced water quality model.

    Science.gov (United States)

    Cao, Bibo; Li, Chuan; Liu, Yan; Zhao, Yue; Sha, Jian; Wang, Yuqiu

    2015-05-01

    Because water quality monitoring sections or sites could reflect the water quality status of rivers, surface water quality management based on water quality monitoring sections or sites would be effective. For the purpose of improving water quality of rivers, quantifying the contribution ratios of pollutant resources to a specific section is necessary. Because physical and chemical processes of nutrient pollutants are complex in water bodies, it is difficult to quantitatively compute the contribution ratios. However, water quality models have proved to be effective tools to estimate surface water quality. In this project, an enhanced QUAL2Kw model with an added module was applied to the Xin'anjiang Watershed, to obtain water quality information along the river and to assess the contribution ratios of each pollutant source to a certain section (the Jiekou state-controlled section). Model validation indicated that the results were reliable. Then, contribution ratios were analyzed through the added module. Results show that among the pollutant sources, the Lianjiang tributary contributes the largest part of total nitrogen (50.43%), total phosphorus (45.60%), ammonia nitrogen (32.90%), nitrate (nitrite + nitrate) nitrogen (47.73%), and organic nitrogen (37.87%). Furthermore, contribution ratios in different reaches varied along the river. Compared with pollutant loads ratios of different sources in the watershed, an analysis of contribution ratios of pollutant sources for each specific section, which takes the localized chemical and physical processes into consideration, was more suitable for local-regional water quality management. In summary, this method of analyzing the contribution ratios of pollutant sources to a specific section based on the QUAL2Kw model was found to support the improvement of the local environment.

  2. Plugger guide for aligning an end plug and a fuel rod tube end

    International Nuclear Information System (INIS)

    Klapper, K.K.; Boatwright, D.A.

    1987-01-01

    A pin driving tool is described for inserting or removing pins from teeth on a digging means, comprising: fuel rod tube toward an end plug for application of the end plug into the tube end, the apparatus comprising: (a) a guide housing having an elongated central longitudinal bore with one end for receiving the end plug and an opposite end for receiving the fuel rod tube end; (b) sets of rolling elements disposed in the housing at axially spaced positions along and about the bore thereof. The rolling elements in each set are positioned in fixed relation with respect to one another to receive the fuel rod tube end therebetween and align the tube end with the end plug as the tube end is moved through the bore and into engagement with the end plug; and (c) retaining means disposed adjacent to the open end of the housing bore for engaging the end plug so as to maintain it in a stationary seated position at the one end of the housing bore

  3. Instantaneous flow field above the free end of finite-height cylinders and prisms

    International Nuclear Information System (INIS)

    Rostamy, N.; Sumner, D.; Bergstrom, D.J.; Bugg, J.D.

    2013-01-01

    Highlights: • PIV measurements of the flow above the free end of finite-height bodies. • Effect of cross-sectional shape of the models on the instantaneous flow. • Small-scale structures generated by the separated shear layer were revealed. • Effect of aspect ratio on the reattachment of the separated flow on the free end. -- Abstract: The flow above the free ends of surface-mounted finite-height circular cylinders and square prisms was studied experimentally using particle image velocimetry (PIV). Cylinders and prisms with aspect ratios of AR = 9, 7, 5, and 3 were tested at a Reynolds number of Re = 4.2 × 10 4 . The bodies were mounted normal to a ground plane and were partially immersed in a turbulent zero-pressure-gradient boundary layer, where the boundary layer thickness relative to the body width was δ/D = 1.6. PIV measurements were made above the free ends of the bodies in a vertical plane aligned with the flow centreline. The present PIV results provide insight into the effects of aspect ratio and body shape on the instantaneous flow field. The recirculation zone under the separated shear layer is larger for the square prism of AR = 3 compared to the more slender prism of AR = 9. Also, for a square prism with low aspect ratio (AR = 3), the influence of the reverse flow over the free end surface becomes more significant compared to that for a higher aspect ratio (AR = 9). For the circular cylinder, a cross-stream vortex forms within the recirculation zone. As the aspect ratio of the cylinder decreases, the reattachment point of the separated flow on the free end surface moves closer to the trailing edge. For both the square prism and circular cylinder cases, the instantaneous velocity vector field and associated in-plane vorticity field revealed small-scale structures mostly generated by the separated shear layer

  4. Technology of interdisciplinary open-ended designing in engineering education

    Science.gov (United States)

    Isaev, A. P.; Plotnikov, L. V.; Fomin, N. I.

    2017-11-01

    Author’s technology of interdisciplinary open-ended engineering is presented in this article. This technology is an integrated teaching method that significantly increases the practical component in the educational program. Author’s technology creates the conditions to overcome the shortcomings in the engineering education. The basic ideas of the technology of open-ended engineering, experience of their implementation in higher education and the author’s vision of the teaching technology are examined in the article. The main stages of development process of the author’s technology of open-ended engineering to prepare students (bachelor) of technical profile are presented in the article. Complex of the methodological tools and procedures is shown in the article. This complex is the basis of the developed training technology that is used in educational process in higher school of engineering (UrFU). The organizational model of the technology of open-ended engineering is presented. Organizational model integrates the functions in the creation and implementation of all educational program. Analysis of the characteristics of educational activity of students working on author’s technology of interdisciplinary open-ended engineering is presented. Intermediate results of the application of author’s technology in the educational process of the engineering undergraduate are shown.

  5. Statistical Model Analysis of (n, α Cross Sections for 4.0-6.5 MeV Neutrons

    Directory of Open Access Journals (Sweden)

    Khuukhenkhuu G.

    2016-01-01

    Full Text Available The statistical model based on the Weisskopf-Ewing theory and constant nuclear temperature approximation is used for systematical analysis of the 4.0-6.5 MeV neutron induced (n, α reaction cross sections. The α-clusterization effect was considered in the (n, α cross sections. A certain dependence of the (n, α cross sections on the relative neutron excess parameter of the target nuclei was observed. The systematic regularity of the (n, α cross sections behaviour is useful to estimate the same reaction cross sections for unstable isotopes. The results of our analysis can be used for nuclear astrophysical calculations such as helium burning and possible branching in the s-process.

  6. STAX-2, Neutron Scattering Cross-Sections by Optical Model and Moldauer Theory with Hauser-Feshbach

    International Nuclear Information System (INIS)

    Tomita, Y.

    1972-01-01

    1 - Nature of physical problem solved: The program calculates neutron scattering cross sections by means of the optical model and Moldauer's theory, and can search for potential parameters which reproduce measured cross sections. The Hauser-Feshbach calculation is also possible. 2 - Restrictions on the complexity of the problem: The maximum number of levels is 25. The largest value of the orbital angular momentum is 10

  7. Structural Analysis of an Integrated Model of Short Straight Section, Service Module, Jumper Connection and Magnet Interconnects for the Large Hadron Collider

    CERN Document Server

    Dutta, S; Kumar, A; Skoczen, B; Soni, H C

    2004-01-01

    The Short Straight Section (SSS) of the Large Hadron Collider (LHC) may undergo relative displacements between cold-mass and cryostat for the following three reasons: - Fabrication tolerance of interconnection bellows - Global smoothing after pre-alignment - Ground motion in a sector of the LHC tunnel The forces responsible for such displacements stem from finite stiffness of interconnect bellows & metal hoses of the internal piping of the jumper connection and from relatively flexible 'glass fibre reinforced epoxy' (GFRE) composite supports of the cold mass. In addition, the vacuum jacket of the jumper connection and the large sleeves attached to both ends of SSS produce elastic deformations of the cryostat vessel. A unified finite element model consisting of cryostat, large sleeves, vacuum jacket of jumper, interconnection bellows, internal piping of jumper, composite cold supports and alignment jacks has been prepared. The knowledge of the position of the cold mass with respect to its cryostat under va...

  8. An Economic Case for End System Multicast

    Science.gov (United States)

    Analoui, Morteza; Rezvani, Mohammad Hossein

    This paper presents a non-strategic model for the end-system multicast networks based on the concept of replica exchange economy. We believe that microeconomics is a good candidate to investigate the problem of selfishness of the end-users (peers) in order to maximize the aggregate throughput. In this solution concept, the decisions that a peer might make, does not affect the actions of the other peers at all. The proposed mechanism tunes the price of the service in such a way that general equilibrium holds.

  9. Computer calculation of neutron cross sections with Hauser-Feshbach code STAPRE incorporating the hybrid pre-compound emission model

    International Nuclear Information System (INIS)

    Ivascu, M.

    1983-10-01

    Computer codes incorporating advanced nuclear models (optical, statistical and pre-equilibrium decay nuclear reaction models) were used to calculate neutron cross sections needed for fusion reactor technology. The elastic and inelastic scattering (n,2n), (n,p), (n,n'p), (n,d) and (n,γ) cross sections for stable molybdenum isotopes Mosup(92,94,95,96,97,98,100) and incident neutron energy from about 100 keV or a threshold to 20 MeV were calculated using the consistent set of input parameters. The hydrogen production cross section which determined the radiation damage in structural materials of fusion reactors can be simply deduced from the presented results. The more elaborated microscopic models of nuclear level density are required for high accuracy calculations

  10. End-to-End Trade-space Analysis for Designing Constellation Missions

    Science.gov (United States)

    LeMoigne, J.; Dabney, P.; Foreman, V.; Grogan, P.; Hache, S.; Holland, M. P.; Hughes, S. P.; Nag, S.; Siddiqi, A.

    2017-12-01

    cost model represents an aggregate model consisting of Cost Estimating Relationships (CERs) from widely accepted models. The current GUI automatically generates graphics representing metrics such as average revisit time or coverage as a function of cost. The end-to-end system will be demonstrated as part of the presentation.

  11. 17 CFR 239.15A - Form N-1A, registration statement of open-end management investment companies.

    Science.gov (United States)

    2010-04-01

    ... statement of open-end management investment companies. 239.15A Section 239.15A Commodity and Securities... Registration Statements § 239.15A Form N-1A, registration statement of open-end management investment companies... management investment companies other than separate accounts of insurance companies registered under the...

  12. EFEKTIVITAS OPEN-ENDED EXPERIENTIAL LEARNING CASES DALAM PENINGKATAN PERTIMBANGAN PROFESIONAL

    Directory of Open Access Journals (Sweden)

    Andian Ari Istiningrum

    2015-04-01

    Full Text Available Abstrak: Penelitian ini bertujuan untuk mengetahui efektivitas implementasi model pembelajaran Open-Ended Experiential Learning Cases dalam usaha peningkatan kemampuan mahasiswa untuk memberikan pertimbangan profesional. Penelitian ini merupakan penelitian pre-experimental design dengan jenis one-group pretes-postes design. Popolasi penelitian adalah mahasiswa jurusan Akuntansi yang mengambil mata kuliah Akuntansi Keuangan Menengah 1 sebanyak 75 orang, sedangkan sampel yang digunakan adalah 44 orang. Teknik pengambilan sampel dilakukan dengan convenience sampling. Data dikumpulkan dengan tes uraian dan dianalisis dengan uji beda t test untuk sampel berhubungan. Hasil penelitian menunjukkan bahwa terdapat perbedaan signifikan kemampuan mahasiswa dalam memberikan pertimbangan profesional sebelum dan sesudah model pembelajaran open-ended experiential learning cases diimplementasikan yang menunjukkan terjadinya peningkatan pertimbangan profesional setelah mahasiswa mengikuti pembelajaran dengan model pembelajaran openended experiential learning cases. Kata Kunci: open-ended experiential learning cases, pertimbangan profesional THE EFFECTIVENESS OF OPEN-ENDED EXPERIENTIAL LEARNING CASES TO IMPROVE PROFESSIONAL JUDGMENT Abstract: This study was aimed to reveal the effectiveness of the implementation of the open-ended experiential learning cases to improve students’ professional judgment. To achieve this purpose, the study was designed as the pre-experimental design with the one-group pretest-post-test design type. The population of the study was the Accounting Department Students at Yogyakarta State University taking the 1 st Intermediate Financial Accounting course. There were 75 students as the population and 44 students were chosen as the research sample. The sampling technique used was the convenience sampling. The data were collected by using the essay test and analyzed by t-test for paired samples. The findings showed that there was a

  13. Evaluation of the Dignity Care Pathway for community nurses caring for people at the end of life.

    Science.gov (United States)

    Johnston, Bridget; Östlund, Ulrika; Brown, Hilary

    2012-10-01

    People nearing the end of life fear loss of dignity, and a central tenet of palliative care is to help people die with dignity. The Dignity Care Pathway (DCP) is an intervention based on the Chochinov theoretical model of dignity care. It has four sections: a manual, a Patient Dignity Inventory, reflective questions, and care actions. The feasibility and acceptability of the DCP were evaluated using a qualitative design with a purposive sample of community nurses. Data was collected from April to October 2010 using in-depth interviews, reflective diaries, and case studies and then analysed using framework analysis. The DCP was acceptable to the community nurses, helped them identify when patients were at the end of life, identified patients' key concerns, and aided nurses in providing holistic end-of-life care. It requires the nurse to have excellent communication skills. Some of the nurses found it hard to initiate a conversation on dignity-conserving care. The DCP helps nurses to deliver individualised care and psychological care, which has previously been identified as a difficult area for community nurses. All of the nurses wished to continue to use the DCP and would recommend it to others.

  14. Introduction to the physics of the total cross section at LHC. A review of data and models

    Energy Technology Data Exchange (ETDEWEB)

    Pancheri, Giulia [INFN Frascati National Laboratory, Frascati (Italy); Massachusetts Institute of Technology, Center for Theoretical Physics, Cambridge, MA (United States); Srivastava, Yogendra N. [University of Perugia, Physics Department, Perugia (Italy); Northeastern University, Physics Department, Boston, MA (United States)

    2017-03-15

    This review describes the development of the physics of hadronic cross sections up to recent LHC results and cosmic ray experiments. We present here a comprehensive review - written with a historical perspective - about total cross sections from medium to the highest energies explored experimentally and studied through a variety of methods and theoretical models for over 60 years. We begin by recalling the analytic properties of the elastic amplitude and the theorems about the asymptotic behavior of the total cross section. A discussion of how proton-proton cross sections are extracted from cosmic rays at higher than accelerator energies and help the study of these asymptotic limits, is presented. This is followed by a description of the advent of particle colliders, through which high energies and unmatched experimental precisions have been attained. Thus the measured hadronic elastic and total cross sections have become crucial instruments to probe the so called soft part of QCD physics, where quarks and gluons are confined, and have led to test and refine Regge behavior and a number of diffractive models. As the c.m. energy increases, the total cross section also probes the transition into hard scattering describable with perturbative QCD, the so-called mini-jet region. Further tests are provided by cross section measurements of γp, γ*p and γ*γ* for models based on vector meson dominance, scaling limits of virtual photons at high Q{sup 2} and the BFKL formalism. Models interpolating from virtual to real photons are also tested. It seems to us to be a necessary task to explore bit-by-bit the rigorous consequences of analyticity, unitarity and crossing. Who knows if someday one will not be able to reassemble the pieces of the puzzle. - A. Martin and F. Cheung, based on 1967 A.M. Lectures at Brandeis Summer School and Lectures at SUNY and Stony Brook (Martin and Cheung in Analyticity properties and bounds of the scattering amplitudes. Gordon and Breach Science

  15. Means-end theory of lifestyle: A replication in the UK

    DEFF Research Database (Denmark)

    Scholderer, Joachim; Brunsø, Karen; Grunert, Klaus G.

    Brunsø, Scholderer and Grunert (submitted, 2000) reconstruct means-end chain theory and lifestyle within a dual-process framework, incorporating bottom-up and top-down information-processing routes. The bottom-up route of their model is defined as a hierarchical categorization process, and the top...... of the intervening knowledge structures is considered a necessary condition for both information-processing routes to reach their ends, predicting a complete-mediation model. The initial study by Brunsø et al. (2000) was exactly replicated based on survey data gathered in the United Kingdom in 1998, using the 'list...... modeling. Compared against five alternative model structures, the complete-mediation model fitted the data best, thus confirming the predictions derived from reconstructed theory, and cross-validating the initial model in a different consumer population....

  16. Right Heart End-Systolic Remodeling Index Strongly Predicts Outcomes in Pulmonary Arterial Hypertension: Comparison With Validated Models.

    Science.gov (United States)

    Amsallem, Myriam; Sweatt, Andrew J; Aymami, Marie C; Kuznetsova, Tatiana; Selej, Mona; Lu, HongQuan; Mercier, Olaf; Fadel, Elie; Schnittger, Ingela; McConnell, Michael V; Rabinovitch, Marlene; Zamanian, Roham T; Haddad, Francois

    2017-06-01

    Right ventricular (RV) end-systolic dimensions provide information on both size and function. We investigated whether an internally scaled index of end-systolic dimension is incremental to well-validated prognostic scores in pulmonary arterial hypertension. From 2005 to 2014, 228 patients with pulmonary arterial hypertension were prospectively enrolled. RV end-systolic remodeling index (RVESRI) was defined by lateral length divided by septal height. The incremental values of RV free wall longitudinal strain and RVESRI to risk scores were determined. Mean age was 49±14 years, 78% were female, 33% had connective tissue disease, 52% were in New York Heart Association class ≥III, and mean pulmonary vascular resistance was 11.2±6.4 WU. RVESRI and right atrial area were strongly connected to the other right heart metrics. Three zones of adaptation (adapted, maladapted, and severely maladapted) were identified based on the RVESRI to RV systolic pressure relationship. During a mean follow-up of 3.9±2.4 years, the primary end point of death, transplant, or admission for heart failure was reached in 88 patients. RVESRI was incremental to risk prediction scores in pulmonary arterial hypertension, including the Registry to Evaluate Early and Long-Term PAH Disease Management score, the Pulmonary Hypertension Connection equation, and the Mayo Clinic model. Using multivariable analysis, New York Heart Association class III/IV, RVESRI, and log NT-proBNP (N-Terminal Pro-B-Type Natriuretic Peptide) were retained (χ 2 , 62.2; P right heart metrics, RVESRI demonstrated the best test-retest characteristics. RVESRI is a simple reproducible prognostic marker in patients with pulmonary arterial hypertension. © 2017 American Heart Association, Inc.

  17. Promoting excellence in end-of-life care: a report on innovative models of palliative care.

    Science.gov (United States)

    Byock, Ira; Twohig, Jeanne Sheils; Merriman, Melanie; Collins, Karyn

    2006-02-01

    Promoting Excellence in End-of Life Care, a national program of The Robert Wood Johnson Foundation, funded 22 demonstration projects representing a wide range of health care settings and patient populations to develop innovative models for delivering palliative care that addressed documented deficiencies in the care of patients and families facing the final stage of life. To determine the practicality (feasibility of development and operation as well as acceptance by stakeholders) of new models of care and to determine the impact of the models on access to, quality of and financing for palliative care. The program cannot report scientifically rigorous outcomes, but the grant-funded projects used a variety of methods and measures to assess acceptance of new models and their impact from the perspectives of various stakeholders, including patients and their families, clinicians, administrators and payers. While it is not possible to aggregate data across projects, the data reported to the Promoting Excellence national program office were used to describe program impact with respect to the practicality of palliative care service integration into existing clinical care settings (feasibility and acceptance by stakeholders), the availability and use of palliative care services (access), quality of care (conformance to patient expectations and accepted clinical standards) and costs of care. The 22 projects provided services in urban as well as rural settings, in integrated health systems, hospitals, outpatient clinics, cancer centers, nursing homes, renal dialysis clinics, inner city public health and safety net systems and prisons. Populations served included prison inmates, military veterans, renal dialysis patients, Native Americans, Native Alaskans, and African American patients, inner-city medically underserved patients, pediatric patients, and persons with serious mental illness patients. Hosting or adopting institutions sustained or expanded twenty of the 22 models

  18. Cox proportional hazards models have more statistical power than logistic regression models in cross-sectional genetic association studies

    NARCIS (Netherlands)

    van der Net, Jeroen B.; Janssens, A. Cecile J. W.; Eijkemans, Marinus J. C.; Kastelein, John J. P.; Sijbrands, Eric J. G.; Steyerberg, Ewout W.

    2008-01-01

    Cross-sectional genetic association studies can be analyzed using Cox proportional hazards models with age as time scale, if age at onset of disease is known for the cases and age at data collection is known for the controls. We assessed to what degree and under what conditions Cox proportional

  19. The role of nonlinear torsional contributions on the stability of flexural-torsional oscillations of open-cross section beams

    Science.gov (United States)

    Di Egidio, Angelo; Contento, Alessandro; Vestroni, Fabrizio

    2015-12-01

    An open-cross section thin-walled beam model, already developed by the authors, has been conveniently simplified while maintaining the capacity of accounting for the significant nonlinear warping effects. For a technical range of geometrical and mechanical characteristics of the beam, the response is characterized by the torsional curvature prevailing over the flexural ones. A Galerkin discretization is performed by using a suitable expansion of displacements based on shape functions. The attention is focused on the dynamic response of the beam to a harmonic force, applied at the free end of the cantilever beam. The excitation is directed along the symmetry axis of the beam section. The stability of the one-component oscillations has been investigated using the analytical model, showing the importance of the internal resonances due to the nonlinear warping coupling terms. Comparison with the results provided by a computational finite element model has been performed. The good agreement among the results of the analytical and the computational models confirms the effectiveness of the simplified model of a nonlinear open-cross section thin-walled beam and overall the important role of the warping and of the torsional elongation in the study of the one-component dynamic oscillations and their stability.

  20. A new modelling of the multigroup scattering cross section in deterministic codes for neutron transport

    International Nuclear Information System (INIS)

    Calloo, A.A.

    2012-01-01

    In reactor physics, calculation schemes with deterministic codes are validated with respect to a reference Monte Carlo code. The remaining biases are attributed to the approximations and models induced by the multigroup theory (self-shielding models and expansion of the scattering law using Legendre polynomials) to represent physical phenomena (resonant absorption and scattering anisotropy respectively). This work focuses on the relevance of a polynomial expansion to model the scattering law. Since the outset of reactor physics, the latter has been expanded on a truncated Legendre polynomial basis. However, the transfer cross sections are highly anisotropic, with non-zero values for a very small range of the cosine of the scattering angle. Besides, the finer the energy mesh and the lighter the scattering nucleus, the more exacerbated is the peaked shape of this cross section. As such, the Legendre expansion is less suited to represent the scattering law. Furthermore, this model induces negative values which are non-physical. In this work, various scattering laws are briefly described and the limitations of the existing model are pointed out. Hence, piecewise-constant functions have been used to represent the multigroup scattering cross section. This representation requires a different model for the diffusion source. The discrete ordinates method which is widely employed to solve the transport equation has been adapted. Thus, the finite volume method for angular discretization has been developed and implemented in Paris environment which hosts the S n solver, Snatch. The angular finite volume method has been compared to the collocation method with Legendre moments to ensure its proper performance. Moreover, unlike the latter, this method is adapted for both the Legendre moments and the piecewise-constant functions representations of the scattering cross section. This hybrid-source method has been validated for different cases: fuel cell in infinite lattice

  1. An optimum cold end configuration for helium liquefaction cycles

    International Nuclear Information System (INIS)

    Minta, M.; Smith, J.L.

    1984-01-01

    This chapter examines the effect of the non-ideal behavior of helium at low temperature on the performance of helium liquefaction cycles. The effect is isolated by means of a continuum model for the precooling stage. The cold end losses are due primarily to the composite effect of the non-ideality of helium at low temperatures and the heat exchanger losses, in addition to the component losses fixed by the expander/compressor efficiencies. Topics considered include continuously distributed full-pressure ratio expanders, continuously distributed full-flow expanders, the heat exchange effect (ideal gas working fluid, real gas working fluid), and cold end configuration. The cold end configuration minimizes the cycle cold end losses

  2. The first section of the CMS detector (centre of photo) arriving from the vertical shaft, viewed from the cavern floor.

    CERN Document Server

    Maximilien Brice

    2006-01-01

    In the early morning of 2 November, the first section of the CMS detector began its eagerly awaited descent into the underground cavern. You may imagine the CMS detector as a loaf of sliced bread, cut into 15 slices of different sizes. The two HF sections are the end pieces; the slices in between will be lowered sequentially according to their positions in the ‘loaf', starting from the HF+ section at the far end of the cavern, towards the access shaft at the opposite end.

  3. IMPROVEMENT OF WELDED CONNECTIONS WITH SIDE LAP WELDS BY REDISTRIBUTION OF ALL-WELD METAL ALONG LENGTHS AND CROSS-SECTIONS THEREOF USING MECHANIZED AND ROBOTIC WELDING SYSTEMS

    Directory of Open Access Journals (Sweden)

    Pavlov Evgeniy Igorevich

    2017-05-01

    Full Text Available Experimental study of bearing capacity of samples of two series performed by semiautomatic welding in CO2 on the axis, and by robotic welding machine in mixture (CO2 + Ar, is presented. Welds of constant cross section, welds with extended leg on end sections, and welds in the form of two dowels on end sections were performed. Efficiency of pilot samples of the first series (with extended leg on end sections by way of a smooth transition defined by the ratio of weld metal volume to a crushing load reaches 28 % relative to samples with a leg constant as per length. Samples of the first series with an extended leg on end sections also showed efficiency increased to 17 %. According to the second series samples test results, the exceeding of bearing capacity of the samples performed with an extended leg on end sections by 24 % in comparison with the samples with a leg of constant cross section was determined. Samples of the second series performed in the form of two dowels on end sections demonstrated the exceeding of the relative bearing capacity by 42 % in comparison with the samples with a continuous leg of constant cross-section.

  4. Surface Generation Modeling in Ball Nose End Milling: a review of relevant literature

    DEFF Research Database (Denmark)

    Bissacco, Giuliano

    One of the most common metal removal operation used in industry is the milling process. This machining process is well known since the beginning of last century and has experienced, along the years, many improvements of the basic technology, as concerns tools, machine tools, coolants...... to be adjusted afterwards. Nevertheless, many efforts have been done during the last 50 years in order to realize prediction tools for machining processes and particularly for conventional turning and milling operations. Most of these models aim at prediction of cutting forces tool wear and tool life. However...... been addressed in this direction. Among all the machining operations, ball nose end milling has shown great potentials, particularly in machining of sculptured surfaces with high requirements in terms of surface finish; this is due to the good spatial agreement of the mill shape with the geometry...

  5. Differences in nulliparous caesarean section rates across models of care: a decomposition analysis.

    LENUS (Irish Health Repository)

    Brick, Aoife

    2016-01-01

    To evaluate the extent of the difference in elective (ELCS) and emergency (EMCS) caesarean section (CS) rates between nulliparous women in public maternity hospitals in Ireland by model of care, and to quantify the contribution of maternal, clinical, and hospital characteristics in explaining the difference in the rates.

  6. 40 CFR 63.494 - Back-end process provisions-residual organic HAP limitations.

    Science.gov (United States)

    2010-07-01

    ... organic HAP limitations. 63.494 Section 63.494 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... § 63.494 Back-end process provisions—residual organic HAP limitations. (a) The monthly weighted average residual organic HAP content of all grades of elastomer processed, measured after the stripping operation...

  7. Organizational home care models across Europe: A cross sectional study.

    Science.gov (United States)

    Van Eenoo, Liza; van der Roest, Henriëtte; Onder, Graziano; Finne-Soveri, Harriet; Garms-Homolova, Vjenka; Jonsson, Palmi V; Draisma, Stasja; van Hout, Hein; Declercq, Anja

    2018-01-01

    Decision makers are searching for models to redesign home care and to organize health care in a more sustainable way. The aim of this study is to identify and characterize home care models within and across European countries by means of structural characteristics and care processes at the policy and the organization level. At the policy level, variables that reflected variation in health care policy were included based on a literature review on the home care policy for older persons in six European countries: Belgium, Finland, Germany, Iceland, Italy, and the Netherlands. At the organizational level, data on the structural characteristics and the care processes were collected from 36 home care organizations by means of a survey. Data were collected between 2013 and 2015 during the IBenC project. An observational, cross sectional, quantitative design was used. The analyses consisted of a principal component analysis followed by a hierarchical cluster analysis. Fifteen variables at the organizational level, spread across three components, explained 75.4% of the total variance. The three components made it possible to distribute home care organizations into six care models that differ on the level of patient-centered care delivery, the availability of specialized care professionals, and the level of monitoring care performance. Policy level variables did not contribute to distinguishing between home care models. Six home care models were identified and characterized. These models can be used to describe best practices. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Algorithm for Solution of Direct Kinematic Problem of Multi-sectional Manipulator with Parallel Structure

    Directory of Open Access Journals (Sweden)

    A. L. Lapikov

    2014-01-01

    Full Text Available The article is aimed at creating techniques to study multi-sectional manipulators with parallel structure. To solve this task the analysis in the field concerned was carried out to reveal both advantages and drawbacks of such executive mechanisms and main problems to be encountered in the course of research. The work shows that it is inefficient to create complete mathematical models of multisectional manipulators, which in the context of solving a direct kinematic problem are to derive a functional dependence of location and orientation of the end effector on all the generalized coordinates of the mechanism. The structure of multisectional manipulators was considered, where the sections are platform manipulators of parallel kinematics with six degrees of freedom. The paper offers an algorithm to define location and orientation of the end effector of the manipulator by means of iterative solution of analytical equation of the moving platform plane for each section. The equation for the unknown plane is derived using three points, which are attachment points of the moving platform joints. To define the values of joint coordinates a system of nine non-linear equations is completed. It is necessary to mention that for completion of the equation system are used the equations with the same type of non-linearity. The physical sense of all nine equations of the system is Euclidean distance between the points of the manipulator. The result of algorithm execution is a matrix of homogenous transformation for each section. The correlations describing transformations between adjoining sections of the manipulator are given. An example of the mechanism consisting of three sections is examined. The comparison of theoretical calculations with results obtained on a 3D-prototype is made. The next step of the work is to conduct research activities both in the field of dynamics of platform parallel kinematics manipulators with six degrees of freedom and in the

  9. 49 CFR 231.3 - Drop-end high-side gondola cars.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Drop-end high-side gondola cars. 231.3 Section 231... gondola cars. (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see § 231.1(a)(1)). (2) Dimensions. Same as specified for “Box and other house cars” (see § 231.1(a)(2)). (3...

  10. 49 CFR 231.5 - Drop-end low-side gondola cars.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Drop-end low-side gondola cars. 231.5 Section 231... gondola cars. (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see § 231.1(a)(1)). (2) Dimensions. Same as specified for “Box and other house cars” (see § 231.1(a)(2)). (3...

  11. An End-to-End System to Enable Quick, Easy and Inexpensive Deployment of Hydrometeorological Stations

    Science.gov (United States)

    Celicourt, P.; Piasecki, M.

    2014-12-01

    The high cost of hydro-meteorological data acquisition, communication and publication systems along with limited qualified human resources is considered as the main reason why hydro-meteorological data collection remains a challenge especially in developing countries. Despite significant advances in sensor network technologies which gave birth to open hardware and software, low-cost (less than $50) and low-power (in the order of a few miliWatts) sensor platforms in the last two decades, sensors and sensor network deployment remains a labor-intensive, time consuming, cumbersome, and thus expensive task. These factors give rise for the need to develop a affordable, simple to deploy, scalable and self-organizing end-to-end (from sensor to publication) system suitable for deployment in such countries. The design of the envisioned system will consist of a few Sensed-And-Programmed Arduino-based sensor nodes with low-cost sensors measuring parameters relevant to hydrological processes and a Raspberry Pi micro-computer hosting the in-the-field back-end data management. This latter comprises the Python/Django model of the CUAHSI Observations Data Model (ODM) namely DjangODM backed by a PostgreSQL Database Server. We are also developing a Python-based data processing script which will be paired with the data autoloading capability of Django to populate the DjangODM database with the incoming data. To publish the data, the WOFpy (WaterOneFlow Web Services in Python) developed by the Texas Water Development Board for 'Water Data for Texas' which can produce WaterML web services from a variety of back-end database installations such as SQLite, MySQL, and PostgreSQL will be used. A step further would be the development of an appealing online visualization tool using Python statistics and analytics tools (Scipy, Numpy, Pandas) showing the spatial distribution of variables across an entire watershed as a time variant layer on top of a basemap.

  12. A simplified unified Hauser-Feshbach/Pre-Equilibrium model for calculating double differential cross sections

    International Nuclear Information System (INIS)

    Fu, C.Y.

    1988-01-01

    A unified Hauser-Feshbach/Pre-Equilibrium model is extended and simplified. The extension involves the addition of correlations among states of different total quantum numbers (J and J') and the introduction of consistent level density formulas for the H-F and the P-E parts of the calculation. The simplification, aimed at reducing the computational cost, is achieved mainly by keeping only the off-diagonal terms that involve strongly correlated 2p-1h states. A correlation coefficient is introduced to fit the experimental data. The model has been incorporated into the multistep H-F model code TNG. Calculated double differential (n,xn) cross sections at 14 and 25.7 MeV for iron, niobium, and bismuth are in good agreement with experiments. In use at ORNL and JAERI, the TNG code in various stages of development has been applied with success to the evaluation of double differential (n,xn) cross sections from 1 to 20 MeV for the dominant isotopes of chromium, manganese, iron, nickel, copper, and lead. 11 refs., 2 figs

  13. Unmanned Aircraft Systems Minimum Operations Performance Standards End-to-End Verification and Validation (E2-V2) Simulation

    Science.gov (United States)

    Ghatas, Rania W.; Jack, Devin P.; Tsakpinis, Dimitrios; Vincent, Michael J.; Sturdy, James L.; Munoz, Cesar A.; Hoffler, Keith D.; Dutle, Aaron M.; Myer, Robert R.; Dehaven, Anna M.; hide

    2017-01-01

    As Unmanned Aircraft Systems (UAS) make their way to mainstream aviation operations within the National Airspace System (NAS), research efforts are underway to develop a safe and effective environment for their integration into the NAS. Detect and Avoid (DAA) systems are required to account for the lack of "eyes in the sky" due to having no human on-board the aircraft. The current NAS relies on pilot's vigilance and judgement to remain Well Clear (CFR 14 91.113) of other aircraft. RTCA SC-228 has defined DAA Well Clear (DAAWC) to provide a quantified Well Clear volume to allow systems to be designed and measured against. Extended research efforts have been conducted to understand and quantify system requirements needed to support a UAS pilot's ability to remain well clear of other aircraft. The efforts have included developing and testing sensor, algorithm, alerting, and display requirements. More recently, sensor uncertainty and uncertainty mitigation strategies have been evaluated. This paper discusses results and lessons learned from an End-to-End Verification and Validation (E2-V2) simulation study of a DAA system representative of RTCA SC-228's proposed Phase I DAA Minimum Operational Performance Standards (MOPS). NASA Langley Research Center (LaRC) was called upon to develop a system that evaluates a specific set of encounters, in a variety of geometries, with end-to-end DAA functionality including the use of sensor and tracker models, a sensor uncertainty mitigation model, DAA algorithmic guidance in both vertical and horizontal maneuvering, and a pilot model which maneuvers the ownship aircraft to remain well clear from intruder aircraft, having received collective input from the previous modules of the system. LaRC developed a functioning batch simulation and added a sensor/tracker model from the Federal Aviation Administration (FAA) William J. Hughes Technical Center, an in-house developed sensor uncertainty mitigation strategy, and implemented a pilot

  14. End-to-End Multimodal Emotion Recognition Using Deep Neural Networks

    Science.gov (United States)

    Tzirakis, Panagiotis; Trigeorgis, George; Nicolaou, Mihalis A.; Schuller, Bjorn W.; Zafeiriou, Stefanos

    2017-12-01

    Automatic affect recognition is a challenging task due to the various modalities emotions can be expressed with. Applications can be found in many domains including multimedia retrieval and human computer interaction. In recent years, deep neural networks have been used with great success in determining emotional states. Inspired by this success, we propose an emotion recognition system using auditory and visual modalities. To capture the emotional content for various styles of speaking, robust features need to be extracted. To this purpose, we utilize a Convolutional Neural Network (CNN) to extract features from the speech, while for the visual modality a deep residual network (ResNet) of 50 layers. In addition to the importance of feature extraction, a machine learning algorithm needs also to be insensitive to outliers while being able to model the context. To tackle this problem, Long Short-Term Memory (LSTM) networks are utilized. The system is then trained in an end-to-end fashion where - by also taking advantage of the correlations of the each of the streams - we manage to significantly outperform the traditional approaches based on auditory and visual handcrafted features for the prediction of spontaneous and natural emotions on the RECOLA database of the AVEC 2016 research challenge on emotion recognition.

  15. Semantic Complex Event Processing over End-to-End Data Flows

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Qunzhi [University of Southern California; Simmhan, Yogesh; Prasanna, Viktor K.

    2012-04-01

    Emerging Complex Event Processing (CEP) applications in cyber physical systems like SmartPower Grids present novel challenges for end-to-end analysis over events, flowing from heterogeneous information sources to persistent knowledge repositories. CEP for these applications must support two distinctive features - easy specification patterns over diverse information streams, and integrated pattern detection over realtime and historical events. Existing work on CEP has been limited to relational query patterns, and engines that match events arriving after the query has been registered. We propose SCEPter, a semantic complex event processing framework which uniformly processes queries over continuous and archived events. SCEPteris built around an existing CEP engine with innovative support for semantic event pattern specification and allows their seamless detection over past, present and future events. Specifically, we describe a unified semantic query model that can operate over data flowing through event streams to event repositories. Compile-time and runtime semantic patterns are distinguished and addressed separately for efficiency. Query rewriting is examined and analyzed in the context of temporal boundaries that exist between event streams and their repository to avoid duplicate or missing results. The design and prototype implementation of SCEPterare analyzed using latency and throughput metrics for scenarios from the Smart Grid domain.

  16. Observations on dual-ended readout of 100 mm long LYSO crystals

    International Nuclear Information System (INIS)

    Ur-Rehman, Fazal; McIntosh, Bryan; Goertzen, Andrew L.

    2011-01-01

    We are investigating using dual-ended readout of axially oriented long thin scintillator crystals in detectors for a compact geometry, small ring diameter animal PET system. The axial position of interaction is determined from the light sharing between two photodetectors at opposite ends of the crystal. We examine the light output, energy resolution and axial spatial resolution of 1.5-5x2x100 mm 3 polished LYSO crystals by irradiating with an electronically collimated beam of 511 keV photons oriented perpendicular to the long axis and read out at either end by position sensitive photomultiplier tubes (PSPMTs). Three reflector materials, namely Teflon, 3 M enhanced specular reflector (ESR) and black paint are examined for the 2x2x100 mm 3 crystal size. The light output increases and energy resolution improves with the crystal cross-section. Generally, the spatial resolution worsens with increase in crystal cross-section. For the 2x2x100 mm 3 crystal size, the mean energy resolutions of the photopeak over the nine irradiation positions were 14.4±0.4%, 16.0±1.2% and 28.3±2.1% with mean spatial resolutions of 7.0±1.0, 9.4±3.3 and 26.0±5.0 mm using ESR, Teflon and black paint, respectively. ESR reflector gave the best light output, energy and axial spatial resolutions. These characterization results of PSPMT-based dual-ended long LYSO crystals will be useful in the design of detector modules for a highly compact geometry preclinical PET system using this detector technology.

  17. Optical model calculation of neutron-nucleus scattering cross sections

    International Nuclear Information System (INIS)

    Smith, M.E.; Camarda, H.S.

    1980-01-01

    A program to calculate the total, elastic, reaction, and differential cross section of a neutron interacting with a nucleus is described. The interaction between the neutron and the nucleus is represented by a spherically symmetric complex potential that includes spin-orbit coupling. This optical model problem is solved numerically, and is treated with the partial-wave formalism of scattering theory. The necessary scattering theory required to solve this problem is briefly stated. Then, the numerical methods used to integrate the Schroedinger equation, calculate derivatives, etc., are described, and the results of various programming tests performed are presented. Finally, the program is discussed from a user's point of view, and it is pointed out how and where the program (OPTICAL) can be changed to satisfy particular needs

  18. Fuel rod end plug

    International Nuclear Information System (INIS)

    McGeary, R.K.; Bucher, G.D.

    1989-01-01

    This patent describes an end plug for welded disposition within the end of a tube. It comprises a circumferentially extending, axially oriented land surface, having a radial extent defined by means of a first predetermined dimension, for disposition within the end of the tube; a circumferentially extending, axially oriented land surface, having a radial extent defined by means of a second predetermined dimension which is greater than the first predetermined dimension, for disposition outside of the end of the tube. The second land surface being disposed upstream of the first land surface; an annularly extending, radially oriented shoulder portion, defined at the downstream end of the second land surface and having a radially inward depth which is greater than the difference defined between the first and second radial dimensions of the first and second land surfaces, for engaging the end of the tube in a butt contact fashion; and annular groove means defined between the upstream end of the first land surface and the shoulder portion of the end plug, for eliminating porosity defects normally developed within a weldment defined between the tube end and the end plug when the end plug is welded within the tube end, and including a conical surface which extends radially outwardly from the innermost radial depth extent of the shoulder portion to the upstream end of the first land surface

  19. Shell-model computed cross sections for charged-current scattering of astrophysical neutrinos off 40Ar

    Science.gov (United States)

    Kostensalo, Joel; Suhonen, Jouni; Zuber, K.

    2018-03-01

    Charged-current (anti)neutrino-40Ar cross sections for astrophysical neutrinos have been calculated. The initial and final nuclear states were calculated using the nuclear shell model. The folded solar-neutrino scattering cross section was found to be 1.78 (23 ) ×10-42cm2 , which is higher than what the previous papers have reported. The contributions from the 1- and 2- multipoles were found to be significant at supernova-neutrino energies, confirming the random-phase approximation (RPA) result of a previous study. The effects of neutrino flavor conversions in dense stellar matter (matter oscillations) were found to enhance the neutrino-scattering cross sections significantly for both the normal and inverted mass hierarchies. For the antineutrino scattering, only a small difference between the nonoscillating and inverted-hierarchy cross sections was found, while the normal-hierarchy cross section was 2-3 times larger than that of the nonoscillating cross section, depending on the adopted parametrization of the Fermi-Dirac distribution. This property of the supernova-antineutrino signal could probably be used to distinguish between the two hierarchies in megaton LAr detectors.

  20. Pricing end-of-life components

    Science.gov (United States)

    Vadde, Srikanth; Kamarthi, Sagar V.; Gupta, Surendra M.

    2005-11-01

    The main objective of a product recovery facility (PRF) is to disassemble end-of-life (EOL) products and sell the reclaimed components for reuse and recovered materials in second-hand markets. Variability in the inflow of EOL products and fluctuation in demand for reusable components contribute to the volatility in inventory levels. To stay profitable the PRFs ought to manage their inventory by regulating the price appropriately to minimize holding costs. This work presents two deterministic pricing models for a PRF bounded by environmental regulations. In the first model, the demand is price dependent and in the second, the demand is both price and time dependent. The models are valid for single component with no inventory replenishment sale during the selling horizon . Numerical examples are presented to illustrate the models.

  1. Automatic provisioning of end-to-end QoS into the home

    DEFF Research Database (Denmark)

    Brewka, Lukasz Jerzy; Skoldström, Pontus; Nelis, Jelle

    2011-01-01

    Due to a growing number of high bandwidth applications today (such as HDTV), and an increasing amount of network and cloud based applications, service providers need to pay attention to QoS in their networks. We believe there is a need for an end-to-end approach reaching into the home as well....... The Home Gateway (HG) as a key component of the home network is crucial for enabling the end-to-end solutions. UPnP-QoS has been proposed as an inhome solution for resource reservations. In this paper we assess a solution for automatic QoS reservations, on behalf of non-UPnP-QoS aware applications....... Additionally we focus on an integrated end-to-end solution, combining GMPLS-based reservations in e.g., access/metro and UPnP-QoS based reservation in the home network....

  2. Dynamic radar cross section measurements of a full-scale aircraft for RCS modelling validation

    CSIR Research Space (South Africa)

    Van Schalkwyk, Richard F

    2017-10-01

    Full Text Available In this paper the process followed in generating a high fidelity reference data set for radar cross section (RCS) modelling validation for a full-scale aircraft, is presented. An overview of two dynamic RCS measurement campaigns, involving both...

  3. Ranking and validation of spallation models for isotopic production cross sections of heavy residua

    Science.gov (United States)

    Sharma, Sushil K.; Kamys, Bogusław; Goldenbaum, Frank; Filges, Detlef

    2017-07-01

    The production cross sections of isotopically identified residual nuclei of spallation reactions induced by 136Xe projectiles at 500AMeV on hydrogen target were analyzed in a two-step model. The first stage of the reaction was described by the INCL4.6 model of an intranuclear cascade of nucleon-nucleon and pion-nucleon collisions whereas the second stage was analyzed by means of four different models; ABLA07, GEM2, GEMINI++ and SMM. The quality of the data description was judged quantitatively using two statistical deviation factors; the H-factor and the M-factor. It was found that the present analysis leads to a different ranking of models as compared to that obtained from the qualitative inspection of the data reproduction. The disagreement was caused by sensitivity of the deviation factors to large statistical errors present in some of the data. A new deviation factor, the A factor, was proposed, that is not sensitive to the statistical errors of the cross sections. The quantitative ranking of models performed using the A-factor agreed well with the qualitative analysis of the data. It was concluded that using the deviation factors weighted by statistical errors may lead to erroneous conclusions in the case when the data cover a large range of values. The quality of data reproduction by the theoretical models is discussed. Some systematic deviations of the theoretical predictions from the experimental results are observed.

  4. Ranking and validation of spallation models for isotopic production cross sections of heavy residua

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Sushil K.; Kamys, Boguslaw [Jagiellonian University, The Marian Smoluchowski Institute of Physics, Krakow (Poland); Goldenbaum, Frank; Filges, Detlef [Forschungszentrum Juelich, Institut fuer Kernphysik, Juelich (Germany)

    2017-07-15

    The production cross sections of isotopically identified residual nuclei of spallation reactions induced by {sup 136}Xe projectiles at 500 AMeV on hydrogen target were analyzed in a two-step model. The first stage of the reaction was described by the INCL4.6 model of an intranuclear cascade of nucleon-nucleon and pion-nucleon collisions whereas the second stage was analyzed by means of four different models; ABLA07, GEM2, GEMINI++ and SMM. The quality of the data description was judged quantitatively using two statistical deviation factors; the H-factor and the M-factor. It was found that the present analysis leads to a different ranking of models as compared to that obtained from the qualitative inspection of the data reproduction. The disagreement was caused by sensitivity of the deviation factors to large statistical errors present in some of the data. A new deviation factor, the A factor, was proposed, that is not sensitive to the statistical errors of the cross sections. The quantitative ranking of models performed using the A-factor agreed well with the qualitative analysis of the data. It was concluded that using the deviation factors weighted by statistical errors may lead to erroneous conclusions in the case when the data cover a large range of values. The quality of data reproduction by the theoretical models is discussed. Some systematic deviations of the theoretical predictions from the experimental results are observed. (orig.)

  5. A model for emergency department end-of-life communications after acute devastating events--part I: decision-making capacity, surrogates, and advance directives.

    Science.gov (United States)

    Limehouse, Walter E; Feeser, V Ramana; Bookman, Kelly J; Derse, Arthur

    2012-09-01

    Making decisions for a patient affected by sudden devastating illness or injury traumatizes a patient's family and loved ones. Even in the absence of an emergency, surrogates making end-of-life treatment decisions may experience negative emotional effects. Helping surrogates with these end-of-life decisions under emergent conditions requires the emergency physician (EP) to be clear, making medical recommendations with sensitivity. This model for emergency department (ED) end-of-life communications after acute devastating events comprises the following steps: 1) determine the patient's decision-making capacity; 2) identify the legal surrogate; 3) elicit patient values as expressed in completed advance directives; 4) determine patient/surrogate understanding of the life-limiting event and expectant treatment goals; 5) convey physician understanding of the event, including prognosis, treatment options, and recommendation; 6) share decisions regarding withdrawing or withholding of resuscitative efforts, using available resources and considering options for organ donation; and 7) revise treatment goals as needed. Emergency physicians should break bad news compassionately, yet sufficiently, so that surrogate and family understand both the gravity of the situation and the lack of long-term benefit of continued life-sustaining interventions. EPs should also help the surrogate and family understand that palliative care addresses comfort needs of the patient including adequate treatment for pain, dyspnea, or anxiety. Part I of this communications model reviews determination of decision-making capacity, surrogacy laws, and advance directives, including legal definitions and application of these steps; Part II (which will appear in a future issue of AEM) covers communication moving from resuscitative to end-of-life and palliative treatment. EPs should recognize acute devastating illness or injuries, when appropriate, as opportunities to initiate end-of-life discussions and to

  6. Paraho environmental data. Part IV. Land reclamation and revegetation. Part V. Biological effects. Part VI. Occupational health and safety. Part VII. End use

    Energy Technology Data Exchange (ETDEWEB)

    Limbach, L.K.

    1982-06-01

    Characteristics of the environment and ecosystems at Anvil Points, reclamation of retorted shale, revegetation of retorted shale, and ecological effects of retorted shale are reported in the first section of this report. Methods used in screening shale oil and retort water for mutagens and carcinogens as well as toxicity studies are reported in the second section of this report. The third section contains information concerning the industrial hygiene and medical studies made at Anvil Points during Paraho research operations. The last section discusses the end uses of shale crude oil and possible health effects associated with end use. (DMC)

  7. Examining the nonparametric effect of drivers' age in rear-end accidents through an additive logistic regression model.

    Science.gov (United States)

    Ma, Lu; Yan, Xuedong

    2014-06-01

    This study seeks to inspect the nonparametric characteristics connecting the age of the driver to the relative risk of being an at-fault vehicle, in order to discover a more precise and smooth pattern of age impact, which has commonly been neglected in past studies. Records of drivers in two-vehicle rear-end collisions are selected from the general estimates system (GES) 2011 dataset. These extracted observations in fact constitute inherently matched driver pairs under certain matching variables including weather conditions, pavement conditions and road geometry design characteristics that are shared by pairs of drivers in rear-end accidents. The introduced data structure is able to guarantee that the variance of the response variable will not depend on the matching variables and hence provides a high power of statistical modeling. The estimation results exhibit a smooth cubic spline function for examining the nonlinear relationship between the age of the driver and the log odds of being at fault in a rear-end accident. The results are presented with respect to the main effect of age, the interaction effect between age and sex, and the effects of age under different scenarios of pre-crash actions by the leading vehicle. Compared to the conventional specification in which age is categorized into several predefined groups, the proposed method is more flexible and able to produce quantitatively explicit results. First, it confirms the U-shaped pattern of the age effect, and further shows that the risks of young and old drivers change rapidly with age. Second, the interaction effects between age and sex show that female and male drivers behave differently in rear-end accidents. Third, it is found that the pattern of age impact varies according to the type of pre-crash actions exhibited by the leading vehicle. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. 2008 annual meeting on nuclear technology. Pt. 1. Section reports; JAHRESTAGUNG KERNTECHNIK 2008. T. 1. Sektionsberichte

    Energy Technology Data Exchange (ETDEWEB)

    Dagan, Ron; Sanchez Espinoza, Victor Hugo [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Reaktorsicherheit; Rohde, U.; Kliem, Soeren [Forschungszentrum Rossendorf e.V. (FZR), Dresden (Germany); Faber, Wolfgang; Berlepsch, Thilo v.; Spann, Holger [E.ON Kernkraft GmbH, Hannover (Germany); Schaffrath, Andreas [TUEV Nord SysTec GmbH und Co. KG, Hamburg (Germany); Schubert, Bernd [Vattenfall Europe Nuclear Energy GmbH, Hamburg (Germany); Rieger, Udo [Vattenfall Nuclear Energy GmbH, Hamburg (Germany); Christ,, Bernhard G. [NUKEM Technologies GmbH, Alzenau (Germany); Gulden, Werner [Fusion for Energy, Barcelona (Spain); Bogusch, Edgar [AREVA NP GmbH, Erlangen (Germany)

    2008-08-15

    Summary report on these 5 - out of 11 - Sections of the Annual Conference on Nuclear Technology held in Hamburg on May 27-29, 2008: - Reactor Physics and Methods of Calculation - Thermodynamics and Fluid Dynamics - Safety of Nuclear Installations - Methods, Analysis, Results - Front End and Back End of the Fuel Cycle, Radioactive Waste, Storage - Fusion Technology. Other Sections will be covered in reports in further issues of atw. (orig.)

  9. Method of drying long-distance pipelines in sections

    Energy Technology Data Exchange (ETDEWEB)

    Steinhaus, H.; Meiners, D.

    1989-04-11

    This invention provides a method of drying long distance pipelines using a vacuum, and provides high-quality drying over the whole length of the pipeline in a manageable and easily followed process. Evacuation of the pipeline is effected by means of a vacuum pump located at least at one point of the section of pipeline. The section is subsequently scavenged or flooded with scavenging gas. After a predetermined reduced pressure is reached, and while the vacuum pump continues to draw off, a scavenging is effected from the end or ends remote from the evacuation point with a molar flow rate of the stream of scavenging gas that is equal to or less than the evacuation stream in throughput, at least initially. The scavenging is effected not from the evacuation point, but from a remote point, and is also effected with a feed speed or feed amount that is throttled at least initially. This ensures that no condensation occurs even in the inner walls of the pipeline.

  10. Commercial equipment loads: End-Use Load and Consumer Assessment Program (ELCAP)

    Energy Technology Data Exchange (ETDEWEB)

    Pratt, R.G.; Williamson, M.A.; Richman, E.E.; Miller, N.E.

    1990-07-01

    The Office of Energy Resources of the Bonneville Power Administration is generally responsible for the agency's power and conservation resource planning. As associated responsibility which supports a variety of office functions is the analysis of historical trends in and determinants of energy consumption. The Office of Energy Resources' End-Use Research Section operates a comprehensive data collection program to provide pertinent information to support demand-side planning, load forecasting, and demand-side program development and delivery. Part of this on-going program is known as the End-Use Load and Consumer Assessment Program (ELCAP), an effort designed to collect electricity usage data through direct monitoring of end-use loads in buildings. This program is conducted for Bonneville by the Pacific Northwest Laboratory. This report provides detailed information on electricity consumption of miscellaneous equipment from the commercial portion of ELCAP. Miscellaneous equipment includes all commercial end-uses except heating, ventilating, air conditioning, and central lighting systems. Some examples of end-uses covered in this report are office equipment, computers, task lighting, refrigeration, and food preparation. Electricity consumption estimates, in kilowatt-hours per square food per year, are provided for each end-use by building type. The following types of buildings are covered: office, retail, restaurant, grocery, warehouse, school, university, and hotel/motel. 6 refs., 35 figs., 12 tabs.

  11. Modelling and simulation of size selectivity in diamond mesh trawl cod-ends

    DEFF Research Database (Denmark)

    Herrmann, Bent

    of the fishing gear. The cod-end is the rearmost part of a trawl where catch accumulates and in which most of the size selection is known to take place. To date, the main method used to assess the selectivity of trawl cod-ends has been to run sea trials followed by statistical analysis of the obtained......Within many fisheries there is a widespread discard of fish. Furthermore, there are several fisheries where fish are caught before reaching the optimal size, leading to an adverse exploitation of the resources. One way to achieve a more optimal exploitation is to improve the size selectivity...

  12. In-plane vibrations of inhomogeneous curved bars having varying cross-section

    International Nuclear Information System (INIS)

    Suzuki, Katsuyoshi; Kosawada, Tadashi; Takahashi, Shin

    1986-01-01

    An exact method using power series expansions is presented for solving in-plane free vibration problems of inhomogeneous curved bars having varying curvatures and cross-sections. Equations of motion and boundary conditions are derived from the stationary conditions of the Lagrangian of curved bars. Natural frequencies and mode shapes are presented for elliptical and circular arc bars having both ends clamped and calmped-free ends. (author)

  13. Performance of a New Model for Predicting End of Flowering Date (bbch 69) of Grapevine (Vitis Vinifera L.)

    Science.gov (United States)

    Gentilucci, Matteo

    2017-04-01

    The end of flowering date (BBCH 69) is an important phenological stage for grapevine (Vitis Vinifera L.), in fact up to this date the growth is focused on the plant and gradually passes on the berries through fruit set. The aim of this study is to perform a model to predict the date of the end of flowering (BBCH69) for some grapevine varieties. This research carried out using three cultivars of grapevine (Maceratino, Montepulciano, Sangiovese) in three different locations (Macerata, Morrovalle and Potenza Picena), places of an equal number of wine farms for the time interval between 2006 and 2013. In order to have reliable temperatures for each location, the data of 6 weather stations near these farms have been interpolated using cokriging methods with elevation as independent variable. The procedure to predict the end of flowering date starts with an investigation of cardinal temperatures typical of each grapevine cultivar. In fact the analysis is characterized by four temperature thresholds (cardinals): minimum activity temperature (TCmin = below this temperature there is no growth for the plant), lower optimal temperature (TLopt = above this temperature there is maximum growth), upper optimal temperature (TUopt = below this temperature there is maximum growth) and maximum activity temperature (TC max = above this temperature there is no growth). Thus this model take into consideration maximum, mean and minimum daily temperatures of each location, relating them with the four above mentioned cultivar temperature thresholds. In this way it has been obtained some possible cases (32) corresponding to as many equations, depending on the position of temperatures compared with the thresholds, in order to calculate the amount of growing degree units (GDU) for each day. Several iterative tests (about 1000 for each cultivar) have been performed, changing the values of temperature thresholds and GDU in order to find the best possible combination which minimizes error

  14. End-to-end tests using alanine dosimetry in scanned proton beams

    Science.gov (United States)

    Carlino, A.; Gouldstone, C.; Kragl, G.; Traneus, E.; Marrale, M.; Vatnitsky, S.; Stock, M.; Palmans, H.

    2018-03-01

    This paper describes end-to-end test procedures as the last fundamental step of medical commissioning before starting clinical operation of the MedAustron synchrotron-based pencil beam scanning (PBS) therapy facility with protons. One in-house homogeneous phantom and two anthropomorphic heterogeneous (head and pelvis) phantoms were used for end-to-end tests at MedAustron. The phantoms were equipped with alanine detectors, radiochromic films and ionization chambers. The correction for the ‘quenching’ effect of alanine pellets was implemented in the Monte Carlo platform of the evaluation version of RayStation TPS. During the end-to-end tests, the phantoms were transferred through the workflow like real patients to simulate the entire clinical workflow: immobilization, imaging, treatment planning and dose delivery. Different clinical scenarios of increasing complexity were simulated: delivery of a single beam, two oblique beams without and with range shifter. In addition to the dose comparison in the plastic phantoms the dose obtained from alanine pellet readings was compared with the dose determined with the Farmer ionization chamber in water. A consistent systematic deviation of about 2% was found between alanine dosimetry and the ionization chamber dosimetry in water and plastic materials. Acceptable agreement of planned and delivered doses was observed together with consistent and reproducible results of the end-to-end testing performed with different dosimetric techniques (alanine detectors, ionization chambers and EBT3 radiochromic films). The results confirmed the adequate implementation and integration of the new PBS technology at MedAustron. This work demonstrates that alanine pellets are suitable detectors for end-to-end tests in proton beam therapy and the developed procedures with customized anthropomorphic phantoms can be used to support implementation of PBS technology in clinical practice.

  15. Snow cover and End of Summer Snowline statistics from a simple stochastic model

    Science.gov (United States)

    Petrelli, A.; Crouzy, B.; Perona, P.

    2012-04-01

    One essential parameter characterizing snow cover statistics is the End Of Summer Snowline (EOSS), which is also a good indicator of actual climatic trends in mountain regions. EOSS is usually modelled by means of spatially distributed physically based models, and typically require heavy parameterization. In this paper we validate the simple stochastic model proposed by Perona et al. (2007), by showing that the snow cover statistics and the position of EOSS can in principle be explained by only four essential (meteorological) parameters. Perona et al. (2007) proposed a model accounting for stochastic snow accumulation in the cold period, and deterministic melting dynamics in the warm period, and studied the statistical distribution of the snowdepth on the long term. By reworking the ensemble average of the steady state evolution equation we single out a relationship between the snowdepth statistics (including the position of EOSS) and the involved parameters. The validation of the established relationship is done using 50 years of field data from 73 Swiss stations located above 2000 m a.s.l. First an estimation of the meteorological parameters is made. Snow height data are used as a precipitation proxy, using temperature data to estimate SWE during the precipitation event. Thresholds are used both to separate accumulation from actual precipitation and wind transport phenomena, and to better assess summer melting rate, considered to be constant over the melting period according to the simplified model. First results show that data for most of the weather stations actually scales with the proposed relationship. This indicates that, on the long term, the effect of spatial and temporal noise masks most of the process detail so that minimalist models suffice to obtain reliable statistics. Future works will test the validity of this approach at different spatial scales, e.g., regional, continental and planetary. Reference: P. Perona, A. Porporato, and L. Ridolfi, "A

  16. Guest Editorial Special Section on Systems of Power Converters: Design, Modeling, Control, and Implementation

    DEFF Research Database (Denmark)

    Liu, Wenxin; Guerrero, Josep M.; Kim, Jang Mok

    2017-01-01

    In this Special Section on Systems of Power Converters: Design, Modeling, Control, and Implementation, we have 11 high-quality papers approved for publication that cover the following three topics. 1) Converter Design and Operation. 2) Subsystem-Level Applications. 3) System-Level Applications...

  17. Aquelarre. A computer code for fast neutron cross sections from the statistical model

    International Nuclear Information System (INIS)

    Guasp, J.

    1974-01-01

    A Fortran V computer code for Univac 1108/6 using the partial statistical (or compound nucleus) model is described. The code calculates fast neutron cross sections for the (n, n'), (n, p), (n, d) and (n, α reactions and the angular distributions and Legendre moments.for the (n, n) and (n, n') processes in heavy and intermediate spherical nuclei. A local Optical Model with spin-orbit interaction for each level is employed, allowing for the width fluctuation and Moldauer corrections, as well as the inclusion of discrete and continuous levels. (Author) 67 refs

  18. Year-End Clinic Handoffs: A National Survey of Academic Internal Medicine Programs.

    Science.gov (United States)

    Phillips, Erica; Harris, Christina; Lee, Wei Wei; Pincavage, Amber T; Ouchida, Karin; Miller, Rachel K; Chaudhry, Saima; Arora, Vineet M

    2017-06-01

    While there has been increasing emphasis and innovation nationwide in training residents in inpatient handoffs, very little is known about the practice and preparation for year-end clinic handoffs of residency outpatient continuity practices. Thus, the latter remains an identified, yet nationally unaddressed, patient safety concern. The 2014 annual Association of Program Directors in Internal Medicine (APDIM) survey included seven items for assessing the current year-end clinic handoff practices of internal medicine residency programs throughout the country. Nationwide survey. All internal medicine program directors registered with APDIM. Descriptive statistics of programs and tools used to formulate a year-end handoff in the ambulatory setting, methods for evaluating the process, patient safety and quality measures incorporated within the process, and barriers to conducting year-end handoffs. Of the 361 APDIM member programs, 214 (59%) completed the Transitions of Care Year-End Clinic Handoffs section of the survey. Only 34% of respondent programs reported having a year-end ambulatory handoff system, and 4% reported assessing residents for competency in this area. The top three barriers to developing a year-end handoff system were insufficient overlap between graduating and incoming residents, inability to schedule patients with new residents in advance, and time constraints for residents, attendings, and support staff. Most internal medicine programs do not have a year-end clinic handoff system in place. Greater attention to clinic handoffs and resident assessment of this care transition is needed.

  19. Integration of End-User Cloud Storage for CMS Analysis

    CERN Document Server

    Riahi, Hassen; Álvarez Ayllón, Alejandro; Balcas, Justas; Ciangottini, Diego; Hernández, José M; Keeble, Oliver; Magini, Nicolò; Manzi, Andrea; Mascetti, Luca; Mascheroni, Marco; Tanasijczuk, Andres Jorge; Vaandering, Eric Wayne

    2018-01-01

    End-user Cloud storage is increasing rapidly in popularity in research communities thanks to the collaboration capabilities it offers, namely synchronisation and sharing. CERN IT has implemented a model of such storage named, CERNBox, integrated with the CERN AuthN and AuthZ services. To exploit the use of the end-user Cloud storage for the distributed data analysis activity, the CMS experiment has started the integration of CERNBox as a Grid resource. This will allow CMS users to make use of their own storage in the Cloud for their analysis activities as well as to benefit from synchronisation and sharing capabilities to achieve results faster and more effectively. It will provide an integration model of Cloud storages in the Grid, which is implemented and commissioned over the world’s largest computing Grid infrastructure, Worldwide LHC Computing Grid (WLCG). In this paper, we present the integration strategy and infrastructure changes needed in order to transparently integrate end-user Cloud storage with...

  20. Preferences for care towards the end of life when decision-making capacity may be impaired: A large scale cross-sectional survey of public attitudes in Great Britain and the United States.

    Directory of Open Access Journals (Sweden)

    Gemma Clarke

    Full Text Available There is continuing public debate about treatment preferences at the end of life, and the acceptability and legal status of treatments that sustain or end life. However, most surveys use binary yes/no measures, and little is known about preferences in neurological disease when decision-making capacity is lost, as most studies focus on cancer. This study investigates changes in public preferences for care towards the end of life, with a focus on measures to sustain or end life.Large-scale international public opinion surveys using a six-stage patient vignette, respondents chose a level of intervention for each stage as health and decision-making capacity deteriorated. Cross-sectional representative samples of the general public in Great Britain and the USA (N = 2016. Primary outcome measure: changes in respondents' preferences for care, measured on a four-point scale designed before data collection. The scale ranged from: maintaining life at all costs; to intervention with agreement; to no intervention; to measures for ending life.There were no significant differences between GB and USA. Preference for measures to sustain life at all costs peaked at short-term memory loss (30.2%, n = 610. Respondents selecting 'measures to help me die peacefully' increased from 3.9% to 37.0% as the condition deteriorated, with the largest increase occurring when decision-making capacity was lost (10.3% to 23.0%. Predictors of choosing 'measures to help me die peacefully' at any stage were: previous personal experience (OR = 1.34, p<0.010, and older age (OR = 1.09 per decade, p<0.010. Negative predictors: living with children (OR = 0.72, p<0.010 and being of "black" race/ethnicity (OR = 0.45, p<0.001.Public opinion was uniform between GB and USA, but markedly heterogeneous. Despite contemporaneous capacitous consent providing an essential legal safeguard in most jurisdictions, there was a high prevalence of preference for "measures to end my life peacefully" when

  1. Measurement of the Standard Model W+W- production cross-section using the ATLAS experiment on the LHC

    International Nuclear Information System (INIS)

    Zeman, Martin

    2014-01-01

    Measurements of di-boson production cross-sections are an important part of the physics programme at the CERN Large Hadron Collider. These physics analyses provide the opportunity to probe the electroweak sector of the Standard Model at the TeV scale and could also indicate the existence of new particles or probe beyond the Standard Model physics. The excellent performance of the LHC through years 2011 and 2012 allowed for very competitive measurements. This thesis provides a comprehensive overview of the experimental considerations and methods used in the measurement of the W + W - production cross-section in proton-proton collisions at √s = 7 TeV and 8 TeV. The treatise covers the material in great detail, starting with the introduction of the theoretical framework of the Standard Model and follows with an extensive discussion of the methods implemented in recording and reconstructing physics events in an experiment of this magnitude. The associated online and offline software tools are included in the discussion. The relevant experiments are covered, including a very detailed section about the ATLAS detector. The final chapter of this thesis contains a detailed description of the analysis of the W-pair production in the leptonic decay channels using the datasets recorded by the ATLAS experiment during 2011 and 2012 (Run I). The analyses use 4.60 fb -1 recorded at √s = 7 TeV and 20.28 fb -1 recorded at 8 TeV. The experimentally measured cross section for the production of W bosons at the ATLAS experiment is consistently enhanced compared to the predictions of the Standard Model at centre-of-mass energies of 7 TeV and 8 TeV. The thesis concludes with the presentation of differential cross-section measurement results. (author) [fr

  2. Current HIV/AIDS end-of-life care in sub-Saharan Africa: a survey of models, services, challenges and priorities

    Directory of Open Access Journals (Sweden)

    O'Neill Joseph F

    2003-10-01

    Full Text Available Abstract Background In response to increased global public health funding initiatives to HIV/AIDS care in Africa, this study aimed to describe practice models, strategies and challenges to delivering end-of-life care in sub-Saharan Africa. Methods A survey end-of-life care programs was conducted, addressing the domains of service aims and configuration, barriers to pain control, governmental endorsement and strategies, funding, monitoring and evaluation, and research. Both closed and qualitative responses were sought. Results Despite great structural challenges, data from 48 programs in 14 countries with a mean annual funding of US $374,884 demonstrated integrated care delivery across diverse settings. Care was commonly integrated with all advanced disease care (67% and disease stages (65% offering care from diagnosis. The majority (98% provided home-based care for a mean of 301 patients. Ninety-four percent reported challenges in pain control (including availability, lack of trained providers, stigma and legal restrictions, and 77% addressed the effects of poverty on disease progression and management. Although 85% of programs reported Government endorsement, end-of-life and palliative care National strategies were largely absent. Conclusions The interdependent tasks of expanding pain control, balancing quality and coverage of care, providing technical assistance in monitoring and evaluation, collaborating between donor agencies and governments, and educating policy makers and program directors of end-of-life care are all necessary if resources are to reach their goals.

  3. Pelvic movement strategies and leg extension power in patients with end-stage medial compartment knee osteoarthritis: a cross-sectional study.

    Science.gov (United States)

    Kierkegaard, Signe; Jørgensen, Peter Bo; Dalgas, Ulrik; Søballe, Kjeld; Mechlenburg, Inger

    2015-09-01

    During movement tasks, patients with medial compartment knee osteoarthritis use compensatory strategies to minimise the joint load of the affected leg. Movement strategies of the knees and trunk have been investigated, but less is known about movement strategies of the pelvis during advancing functional tasks, and how these strategies are associated with leg extension power. The aim of the study was to investigate pelvic movement strategies and leg extension power in patients with end-stage medial compartment knee osteoarthritis compared with controls. 57 patients (mean age 65.6 years) scheduled for medial uni-compartmental knee arthroplasty, and 29 age and gender matched controls were included in this cross-sectional study. Leg extension power was tested with the Nottingham Leg Extension Power-Rig. Pelvic range of motion was derived from an inertia-based measurement unit placed over the sacrum bone during walking, stair climbing and stepping. Patients had lower leg extension power than controls (20-39 %, P 0.06). Furthermore, an inverse association (coefficient: -0.03 to -0.04; R (2) = 13-22 %) between leg extension power and pelvic range of motion during stair and step descending was found in the patients. Compared to controls, patients with medial compartment knee osteoarthritis use greater pelvic movements during advanced functional performance tests, particularly when these involve descending tasks. Further studies should investigate if it is possible to alter these movement strategies by an intervention aimed at increasing strength and power for the patients.

  4. Numerical Study on Ultimate Behaviour of Bolted End-Plate Steel Connections

    Directory of Open Access Journals (Sweden)

    R.E.S. Ismail

    Full Text Available Abstract Bolted end-plate steel connections have become more popular due to ease of fabrication. This paper presents a three dimension Finite Element Model (FEM, using the multi-purpose software ABAQUS, to study the effect of different geometrical parameters on the ultimate behavior of the connection. The proposed model takes into account material and geometrical non-linearities, initial imperfection, contact between adjacent surfaces and the pretension force in the bolts. The Finite Element results are calibrated with published experimental results ''briefly reviewed in this paper'' and verified that the numerical model can simulate and analyze the overall and detailed behavior of different types of bolted end-plate steel connections. Using verified FEM, parametric study is then carried out to study the ultimate behavior with variations in: bolt diameter, end-plate thickness, length of column stiffener, angle of rib stiffener. The results are examined with respect to the failure modes, the evolution of the resistance, the initial stiffness, and the rotation capacity. Finally, the ultimate behavior of the bolted end-plate steel connection is discussed in detail, and recommendations for the design purpose are made.

  5. HADES. A computer code for fast neutron cross section from the Optical Model

    International Nuclear Information System (INIS)

    Guasp, J.; Navarro, C.

    1973-01-01

    A FORTRAN V computer code for UNIVAC 1108/6 using a local Optical Model with spin-orbit interaction is described. The code calculates fast neutron cross sections, angular distribution, and Legendre moments for heavy and intermediate spherical nuclei. It allows for the possibility of automatic variation of potential parameters for experimental data fitting. (Author) 55 refs

  6. End-to-End Assessment of a Large Aperture Segmented Ultraviolet Optical Infrared (UVOIR) Telescope Architecture

    Science.gov (United States)

    Feinberg, Lee; Rioux, Norman; Bolcar, Matthew; Liu, Alice; Guyon, Oliver; Stark, Chris; Arenberg, Jon

    2016-01-01

    Key challenges of a future large aperture, segmented Ultraviolet Optical Infrared (UVOIR) Telescope capable of performing a spectroscopic survey of hundreds of Exoplanets will be sufficient stability to achieve 10^-10 contrast measurements and sufficient throughput and sensitivity for high yield Exo-Earth spectroscopic detection. Our team has collectively assessed an optimized end to end architecture including a high throughput coronagraph capable of working with a segmented telescope, a cost-effective and heritage based stable segmented telescope, a control architecture that minimizes the amount of new technologies, and an Exo-Earth yield assessment to evaluate potential performance. These efforts are combined through integrated modeling, coronagraph evaluations, and Exo-Earth yield calculations to assess the potential performance of the selected architecture. In addition, we discusses the scalability of this architecture to larger apertures and the technological tall poles to enabling it.

  7. Morphology of nerve endings in vocal fold of human newborn.

    Science.gov (United States)

    Gonçalves da Silva Leite, Janaina; Costa Cavalcante, Maria Luzete; Fechine-Jamacaru, Francisco Vagnaldo; de Lima Pompeu, Margarida Maria; Leite, José Alberto Dias; Nascimento Coelho, Dulce Maria; Rabelo de Freitas, Marcos

    2016-10-01

    Sensory receptors are distributed throughout the oral cavity, pharynx, and larynx. Laryngeal sensitivity is crucial for maintaining safe swallowing, thus avoiding silent aspiration. Morphologic description of different receptor types present in larynx vary because of the study of many different species, from mouse to humans. The most commonly sensory structures described in laryngeal mucosa are free nerve endings, taste buds, muscle spindles, glomerular and corpuscular receptors. This study aimed at describing the morphology and the distribution of nerve endings in premature newborn glottic region. Transversal serial frozen sections of the whole vocal folds of three newborns were analyzed using an immuno-histochemical process with a pan-neuronal marker anti-protein gene product 9.5 (PGP 9.5). Imaging was done using a confocal laser microscope. Nerve fiber density in vocal cord was calculated using panoramic images in software Morphometric Analysis System v1.0. Some sensory structures, i.e. glomerular endings and intraepithelial free nerve endings were found in the vocal cord mucosa. Muscle spindles, complex nerve endings (Meissner-like, spherical, rectangular and growing) spiral-wharves nerve structures were identified in larynx intrinsic muscles. Nervous total mean density in vocal cord was similar in the three newborns, although they had different gestational age. The mean nerve fiber density was higher in the posterior region than anterior region of vocal cord. The present results demonstrate the occurrence of different morphotypes of sensory corpuscles and nerve endings premature newborn glottic region and provide information on their sensory systems. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  8. Environmental Sciences Division annual progress report for period ending September 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-01

    This progress report summarizes the research and development activities conducted in the Environmental Sciences Division (ESD) of Oak Ridge National Laboratory during fiscal year (FY) 1993, which extended from October 1, 1992, through September 30, 1993. The report is structured to provide descriptions of current activities and accomplishments in each of the division`s major organizational units. Following the sections describing the organizational units are sections highlighting ESD Scientific, Technical, and Administrative Achievement awards and listing information necessary to convey the scope of the work in the division. An organizational chart of staff and long-term guests who were in ESD and the end of FY 1993 is located in the final section of the report.

  9. Environmental Sciences Division annual progress report for period ending September 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    This progress report summarizes the research and development activities conducted in the Environmental Sciences Division (ESD) of Oak Ridge National Laboratory during fiscal year (FY) 1994, which extended from October 1, 1993, through September 30, 1994. The report is structured to provide descriptions of current activities and accomplishments in each of the division`s major organizational units. Following the sections describing the organizational units are sections highlighting ESD Scientific, Technical, and Administrative Achievement awards and listing information necessary to covey the scope of the work in the division. An organizational chart of staff and long-term guests who wee in ESD at the end of FY 1994 is located in the final section of the report.

  10. Environmental Sciences Division annual progress report for period ending September 30, 1994

    International Nuclear Information System (INIS)

    1994-01-01

    This progress report summarizes the research and development activities conducted in the Environmental Sciences Division (ESD) of Oak Ridge National Laboratory during fiscal year (FY) 1994, which extended from October 1, 1993, through September 30, 1994. The report is structured to provide descriptions of current activities and accomplishments in each of the division's major organizational units. Following the sections describing the organizational units are sections highlighting ESD Scientific, Technical, and Administrative Achievement awards and listing information necessary to covey the scope of the work in the division. An organizational chart of staff and long-term guests who wee in ESD at the end of FY 1994 is located in the final section of the report

  11. Environmental Sciences Division annual progress report for period ending September 30, 1993

    International Nuclear Information System (INIS)

    1994-05-01

    This progress report summarizes the research and development activities conducted in the Environmental Sciences Division (ESD) of Oak Ridge National Laboratory during fiscal year (FY) 1993, which extended from October 1, 1992, through September 30, 1993. The report is structured to provide descriptions of current activities and accomplishments in each of the division's major organizational units. Following the sections describing the organizational units are sections highlighting ESD Scientific, Technical, and Administrative Achievement awards and listing information necessary to convey the scope of the work in the division. An organizational chart of staff and long-term guests who were in ESD and the end of FY 1993 is located in the final section of the report

  12. The Gaussian Graphical Model in Cross-Sectional and Time-Series Data.

    Science.gov (United States)

    Epskamp, Sacha; Waldorp, Lourens J; Mõttus, René; Borsboom, Denny

    2018-04-16

    We discuss the Gaussian graphical model (GGM; an undirected network of partial correlation coefficients) and detail its utility as an exploratory data analysis tool. The GGM shows which variables predict one-another, allows for sparse modeling of covariance structures, and may highlight potential causal relationships between observed variables. We describe the utility in three kinds of psychological data sets: data sets in which consecutive cases are assumed independent (e.g., cross-sectional data), temporally ordered data sets (e.g., n = 1 time series), and a mixture of the 2 (e.g., n > 1 time series). In time-series analysis, the GGM can be used to model the residual structure of a vector-autoregression analysis (VAR), also termed graphical VAR. Two network models can then be obtained: a temporal network and a contemporaneous network. When analyzing data from multiple subjects, a GGM can also be formed on the covariance structure of stationary means-the between-subjects network. We discuss the interpretation of these models and propose estimation methods to obtain these networks, which we implement in the R packages graphicalVAR and mlVAR. The methods are showcased in two empirical examples, and simulation studies on these methods are included in the supplementary materials.

  13. The End

    DEFF Research Database (Denmark)

    Hasse Jørgensen, Stina

    2016-01-01

    Operaen THE END af den japanske komponist og DJ, Keiichiro Shibuya, skubber radikalt til publikums forventninger om, hvad en opera kan og skal være. THE END byder på 3D animation, surround sound, elektronisk glitch og syntetiske stemmer i en kompromisløs virtuel forestilling med det japanske...

  14. End-to-side neurotization with the phrenic nerve in restoring the function of toe extension: an experimental study in a rat model.

    Science.gov (United States)

    Jia, Xiaotian; Chen, Chao; Yang, Jianyun; Yu, Cong

    2018-06-01

    The phrenic nerve being transferred to the posterior division of the lower trunk with end-to-end neurorrhaphy is reported to be effective in restoring the function of digit extension in literature. However, the phrenic nerve is extremely important in respiration. We designed an animal experiment to discover whether the phrenic nerve being transferred to the posterior division of the lower trunk with end-to-side neurotization was feasible and provided the theoretical basis. A sum of 36 Sprague-Dawley rats was randomly assigned to one of two groups. In Group A, the phrenic nerve was transferred to the posterior division of the lower trunk with end-to-side neurotization. In Group B, the posterior division of the lower trunk was directly sutured. The results of behavioral assessment, electrophysiology, histology and nerve fiber count and muscle weight at 12 weeks postoperatively were recorded. In Group A, none of the rats experienced tachypnea. The motion of slight toe extension was observed. The results of electrophysiology, histology and nerve fiber count and muscle weight in Group A were not as well as those of Group B, but gradually improved with time. The phrenic nerve being transferred to the posterior division of lower trunk with end-to-side neurotization can partially restore the function of toe extension in a rat model. Whether the function of digit extension can be restored by the phrenic nerve with end-to-side neurotization in humans still needs more practice in clinic.

  15. MR assessment of end-organ damage in the metabolic syndrome and diabetes mellitus

    NARCIS (Netherlands)

    Schinkel, Linda Danielle van

    2014-01-01

    The first part of this thesis focuses on assessing end-organ damage in individuals with the metabolic syndrome and diabetes mellitus using magnetic resonance imaging (MRI) and spectroscopy (1H-MRS). We performed cross sectional and intervention studies to investigate the contribution of obesity,

  16. Armazenamento refrigerado sob atmosfera modificada de pedúnculos de cajueiro-anão-precoce dos clones CCP-76, end-157, end-183 e end-189 Storage of cashew apples from dwarf clones CCP-76, end-157, end-183 and end-189 under refrigeration and modified atmosphere

    Directory of Open Access Journals (Sweden)

    Auricélia de Souza Morais

    2002-12-01

    Full Text Available Pedúnculos de clones de cajueiro-anão-precoce, dos clones CCP-76, END-157, END-183 e END-189, foram armazenados durante 25 dias, sob refrigeração associada a atmosfera modificada, com o objetivo de avaliar o efeito das condições atualmente utilizadas (5ºC e 85-90% de UR para conservação, transporte e comercialização de cajus in natura. Os pedúnculos foram avaliados a cada 5 dias quanto às seguintes características: perda de peso, firmeza, cor (antocianinas, sólidos e açúcares solúveis, acidez, pH, vitamina C e compostos fenólicos. O uso da refrigeração (5ºC e 85% U.R, associada a atmosfera modificada, proporcionou uma vida útil pós-colheita de 10 dias para o clone END 189, de até 15 dias para o clone END 157 e de até 25 dias para os clones CCP 76 e END 183. A temperatura de 5ºC não se mostrou adequada para armazenamento de pedúnculos de coloração mais intensa (END 157 e END 189 que a testemunha (CCP 76, provocando perda de cor (antocianinas a partir do 10º dia de armazenamento. A atmosfera modificada reduziu significativamente a perda de peso, favorecendo a aparência do produto para comercialização, independentemente do clone estudado.Apples or false fruits from early dwarf cashew clones CCP-76, END-157, END-183 and END-189 were stored for 25 days under refrigeration associated to modified atmosphere with the aim of evaluating the effect of the conditions presently adopted (5ºC and 85-90% RH for conservation, storage and commercialization of fresh cashew apples. The cashew apples were evaluated every 5 days for the following characteristics: weight loss, pulp firmness, color (anthocyannins, acidity, pH, soluble solids, vitamin C and phenolic contents. With the use of refrigeration and modified atmosphere it was possible to attain postharvest storage life of 10 days for clone END 189, 15 days for clone END 157 and up to 25 days for clones CCP 76 and END 183. It was found that 5ºC was not an adequate

  17. Role of end effects in helical aggregation

    NARCIS (Netherlands)

    Gestel, van J.A.M.; Schoot, van der P.P.A.M.; Michels, M.A.J.

    2003-01-01

    End effects are known to play a pivotal role in equilibrium polymerization. To investigate their role in detail, we apply constraints to the first and last bonds of model linear aggregates that exhibit a helix-coil type configurational transition. Three different classes of behavior manifest

  18. The effectiveness of sharp end and rounded end bristle toothbrush

    OpenAIRE

    Paulus Januar; Anastasia Susetyo; Ratih Widyastuti

    2010-01-01

    Background: Numerous designs of manual toothbrush are available in the market with the claims of superiority in plaque removal. It often makes the public confuse which is the best design. The sharp end bristle toothbrush is a modification that commercially available in the market. Purpose: The objective of the study was to compare the effectiveness in plaque removal of the sharp end bristle toothbrush and the rounded end bristle toothbrush. Methods: This clinical trial was a double blind cros...

  19. Volume calculation from limited number of MR imaging sections

    International Nuclear Information System (INIS)

    Wang, J.; Mezrich, R.; Sebok, D.

    1988-01-01

    Magnetic resonance imaging is an accurate and noninvasive way to obtain cardiac geometrical information. For the quantification of left ventricular dynamic parameters, sections are taken along the long axis of the ventricle. Due to the limited number of sections that can be obtained in a reasonable amount of scanning time, the estimation of longitudinal dimension is usually the cause of error in volume calculation. The starting and ending sections are best estimated by guidance of the short axis cuts. This can only guarantee first-order accuracy. Simpson's rule for summation of areas to calculate volume, which is the commonly used method, assumes an accurate knowledge of the starting and ending points of integration. When this assumption is not perfectly met, Simpson's rule tends to unsystemically over- or underestimate the true volume. Due to this concern, some researchers adopt the images from the short axis cut to aid the volume calculation. This can improve the accuracy, but makes the already long scanning time longer. The authors have derived a method of extrapolation and intrapolation based on no more information than usually available to correct the volume over- or underestimated by the Simpson's rule

  20. DNA Breaks and End Resection Measured Genome-wide by End Sequencing.

    Science.gov (United States)

    Canela, Andres; Sridharan, Sriram; Sciascia, Nicholas; Tubbs, Anthony; Meltzer, Paul; Sleckman, Barry P; Nussenzweig, André

    2016-09-01

    DNA double-strand breaks (DSBs) arise during physiological transcription, DNA replication, and antigen receptor diversification. Mistargeting or misprocessing of DSBs can result in pathological structural variation and mutation. Here we describe a sensitive method (END-seq) to monitor DNA end resection and DSBs genome-wide at base-pair resolution in vivo. We utilized END-seq to determine the frequency and spectrum of restriction-enzyme-, zinc-finger-nuclease-, and RAG-induced DSBs. Beyond sequence preference, chromatin features dictate the repertoire of these genome-modifying enzymes. END-seq can detect at least one DSB per cell among 10,000 cells not harboring DSBs, and we estimate that up to one out of 60 cells contains off-target RAG cleavage. In addition to site-specific cleavage, we detect DSBs distributed over extended regions during immunoglobulin class-switch recombination. Thus, END-seq provides a snapshot of DNA ends genome-wide, which can be utilized for understanding genome-editing specificities and the influence of chromatin on DSB pathway choice. Published by Elsevier Inc.