WorldWideScience

Sample records for modeling material property

  1. Probabilistic Modeling of Graded Timber Material Properties

    DEFF Research Database (Denmark)

    Faber, M. H.; Köhler, J.; Sørensen, John Dalsgaard

    2004-01-01

    The probabilistic modeling of timber material characteristics is considered with special emphasis to the modeling of the effect of different quality control and selection procedures used as means for quality grading in the production line. It is shown how statistical models may be established...... an important role in the overall probabilistic modeling. Therefore a scheme for estimating the parameters of probability distribution parameters focusing on the tail behavior has been established using a censored Maximum Likelihood estimation technique. The proposed probabilistic models have been formulated...

  2. Models for acoustical properties of green roof materials

    OpenAIRE

    2011-01-01

    To predict the acoustical effects of green roof structures it is necessary to be able to model the acoustical properties of their materials including gravel. For time domain calculations it is convenient to use the phenomenological model due to Zwikker and Kosten. However this phenomenological model is related to a low frequency/high flow resistivity approximation of more ‘exact’ identical pore models. The results of fitting predictions to short range level difference data and to impedance da...

  3. Analytic Thermoelectric Couple Modeling: Variable Material Properties and Transient Operation

    Science.gov (United States)

    Mackey, Jonathan A.; Sehirlioglu, Alp; Dynys, Fred

    2015-01-01

    To gain a deeper understanding of the operation of a thermoelectric couple a set of analytic solutions have been derived for a variable material property couple and a transient couple. Using an analytic approach, as opposed to commonly used numerical techniques, results in a set of useful design guidelines. These guidelines can serve as useful starting conditions for further numerical studies, or can serve as design rules for lab built couples. The analytic modeling considers two cases and accounts for 1) material properties which vary with temperature and 2) transient operation of a couple. The variable material property case was handled by means of an asymptotic expansion, which allows for insight into the influence of temperature dependence on different material properties. The variable property work demonstrated the important fact that materials with identical average Figure of Merits can lead to different conversion efficiencies due to temperature dependence of the properties. The transient couple was investigated through a Greens function approach; several transient boundary conditions were investigated. The transient work introduces several new design considerations which are not captured by the classic steady state analysis. The work helps to assist in designing couples for optimal performance, and also helps assist in material selection.

  4. Properties of granular analogue model materials: A community wide survey

    Science.gov (United States)

    Klinkmüller, M.; Schreurs, G.; Rosenau, M.; Kemnitz, H.

    2016-08-01

    We report the material properties of 26 granular analogue materials used in 14 analogue modelling laboratories. We determined physical characteristics such as bulk density, grain size distribution, and grain shape, and performed ring shear tests to determine friction angles and cohesion, and uniaxial compression tests to evaluate the compaction behaviour. Mean grain size of the materials varied between c. 100 and 400 μm. Analysis of grain shape factors shows that the four different classes of granular materials (14 quartz sands, 5 dyed quartz sands, 4 heavy mineral sands and 3 size fractions of glass beads) can be broadly divided into two groups consisting of 12 angular and 14 rounded materials. Grain shape has an influence on friction angles, with most angular materials having higher internal friction angles (between c. 35° and 40°) than rounded materials, whereas well-rounded glass beads have the lowest internal friction angles (between c. 25° and 30°). We interpret this as an effect of intergranular sliding versus rolling. Most angular materials have also higher basal friction angles (tested for a specific foil) than more rounded materials, suggesting that angular grains scratch and wear the foil. Most materials have an internal cohesion in the order of 20-100 Pa except for well-rounded glass beads, which show a trend towards a quasi-cohesionless (C < 20 Pa) Coulomb-type material. The uniaxial confined compression tests reveal that rounded grains generally show less compaction than angular grains. We interpret this to be related to the initial packing density after sifting, which is higher for rounded grains than for angular grains. Ring-shear test data show that angular grains undergo a longer strain-hardening phase than more rounded materials. This might explain why analogue models consisting of angular grains accommodate deformation in a more distributed manner prior to strain localisation than models consisting of rounded grains.

  5. Lifelong modelling of properties for materials with technological memory

    Science.gov (United States)

    Falaleev, AP; Meshkov, VV; Vetrogon, AA; Ogrizkov, SV; Shymchenko, AV

    2016-10-01

    An investigation of real automobile parts produced from dual phase steel during standard periods of life cycle is presented, which considers such processes as stamping, exploitation, automobile accident, and further repair. The development of the phenomenological model of the mechanical properties of such parts was based on the two surface plastic theory of Chaboche. As a consequence of the composite structure of dual phase steel, it was shown that local mechanical properties of parts produced from this material change significantly their during their life cycle, depending on accumulated plastic deformations and thermal treatments. Such mechanical property changes have a considerable impact on the accuracy of the computer modelling of automobile behaviour. The most significant errors of modelling were obtained at the critical operating conditions, such as crashes and accidents. The model developed takes into account the kinematics (Bauschinger effect), isotropic hardening, non-linear elastic steel behaviour and changes caused by the thermal treatment. Using finite element analysis, the model allows the evaluation of the passive safety of a repaired car body, and enables increased restoration accuracy following an accident. The model was confirmed experimentally for parts produced from dual phase steel DP780.

  6. Quantitative property-structural relation modeling on polymeric dielectric materials

    Science.gov (United States)

    Wu, Ke

    Nowadays, polymeric materials have attracted more and more attention in dielectric applications. But searching for a material with desired properties is still largely based on trial and error. To facilitate the development of new polymeric materials, heuristic models built using the Quantitative Structure Property Relationships (QSPR) techniques can provide reliable "working solutions". In this thesis, the application of QSPR on polymeric materials is studied from two angles: descriptors and algorithms. A novel set of descriptors, called infinite chain descriptors (ICD), are developed to encode the chemical features of pure polymers. ICD is designed to eliminate the uncertainty of polymer conformations and inconsistency of molecular representation of polymers. Models for the dielectric constant, band gap, dielectric loss tangent and glass transition temperatures of organic polymers are built with high prediction accuracy. Two new algorithms, the physics-enlightened learning method (PELM) and multi-mechanism detection, are designed to deal with two typical challenges in material QSPR. PELM is a meta-algorithm that utilizes the classic physical theory as guidance to construct the candidate learning function. It shows better out-of-domain prediction accuracy compared to the classic machine learning algorithm (support vector machine). Multi-mechanism detection is built based on a cluster-weighted mixing model similar to a Gaussian mixture model. The idea is to separate the data into subsets where each subset can be modeled by a much simpler model. The case study on glass transition temperature shows that this method can provide better overall prediction accuracy even though less data is available for each subset model. In addition, the techniques developed in this work are also applied to polymer nanocomposites (PNC). PNC are new materials with outstanding dielectric properties. As a key factor in determining the dispersion state of nanoparticles in the polymer matrix

  7. Estimating Energy Conversion Efficiency of Thermoelectric Materials: Constant Property Versus Average Property Models

    Science.gov (United States)

    Armstrong, Hannah; Boese, Matthew; Carmichael, Cody; Dimich, Hannah; Seay, Dylan; Sheppard, Nathan; Beekman, Matt

    2017-01-01

    Maximum thermoelectric energy conversion efficiencies are calculated using the conventional "constant property" model and the recently proposed "cumulative/average property" model (Kim et al. in Proc Natl Acad Sci USA 112:8205, 2015) for 18 high-performance thermoelectric materials. We find that the constant property model generally predicts higher energy conversion efficiency for nearly all materials and temperature differences studied. Although significant deviations are observed in some cases, on average the constant property model predicts an efficiency that is a factor of 1.16 larger than that predicted by the average property model, with even lower deviations for temperature differences typical of energy harvesting applications. Based on our analysis, we conclude that the conventional dimensionless figure of merit ZT obtained from the constant property model, while not applicable for some materials with strongly temperature-dependent thermoelectric properties, remains a simple yet useful metric for initial evaluation and/or comparison of thermoelectric materials, provided the ZT at the average temperature of projected operation, not the peak ZT, is used.

  8. A whole range hygric material model: Modelling liquid and vapour transport properties in porous media

    DEFF Research Database (Denmark)

    Scheffler, Gregor Albrecht; Plagge, Rudolf

    2010-01-01

    This paper addresses the modelling of hygric material coefficients bridging the gap between measured material properties and the non-linear storage and transport coefficients in the transfer equation. The conductivity approach and a bundle of tubes model are the basis. By extending this model...

  9. The design and modeling of periodic materials with novel properties

    Science.gov (United States)

    Berger, Jonathan Bernard

    Cellular materials are ubiquitous in our world being found in natural and engineered systems as structural materials, sound and energy absorbers, heat insulators and more. Stochastic foams made of polymers, metals and even ceramics find wide use due to their novel properties when compared to monolithic materials. Properties of these so called hybrid materials, those that combine materials or materials and space, are derived from the localization of thermomechanical stresses and strains on the mesoscale as a function of cell topology. The effects of localization can only be generalized in stochastic materials arising from their inherent potential complexity, possessing variations in local chemistry, microstructural inhomogeneity and topological variations. Ordered cellular materials on the other hand, such as lattices and honeycombs, make for much easier study, often requiring analysis of only a single unit-cell. Theoretical bounds predict that hybrid materials have the potential to push design envelopes offering lighter stiffer and stronger materials. Hybrid materials can achieve very low and even negative coefficients of thermal expansion (CTE) while retaining a relatively high stiffness -- properties completely unmatched by monolithic materials. In the first chapter of this thesis a two-dimensional lattice is detailed that possess near maximum stiffness, relative to the tightest theoretical bound, and low, zero and even appreciably negative thermal expansion. Its CTE and stiffness are given in closed form as a function of geometric parameters and the material properties. This result is confirmed with finite elements (FE) and experiment. In the second chapter the compressive stiffness of three-dimensional ordered foams, both closed and open cell, are predicted with FE and the results placed in property space in terms of stiffness and density. A novel structure is identified that effectively achieves theoretical bounds for Young's, shear and bulk modulus

  10. Application for managing model-based material properties for simulation-based engineering

    Science.gov (United States)

    Hoffman, Edward L [Alameda, CA

    2009-03-03

    An application for generating a property set associated with a constitutive model of a material includes a first program module adapted to receive test data associated with the material and to extract loading conditions from the test data. A material model driver is adapted to receive the loading conditions and a property set and operable in response to the loading conditions and the property set to generate a model response for the material. A numerical optimization module is adapted to receive the test data and the model response and operable in response to the test data and the model response to generate the property set.

  11. Frequency Response of Synthetic Vocal Fold Models with Linear and Nonlinear Material Properties

    Science.gov (United States)

    Shaw, Stephanie M.; Thomson, Scott L.; Dromey, Christopher; Smith, Simeon

    2012-01-01

    Purpose: The purpose of this study was to create synthetic vocal fold models with nonlinear stress-strain properties and to investigate the effect of linear versus nonlinear material properties on fundamental frequency (F[subscript 0]) during anterior-posterior stretching. Method: Three materially linear and 3 materially nonlinear models were…

  12. Using JMatPro to model materials properties and behavior

    Science.gov (United States)

    Saunders, N.; Guo, U. K. Z.; Li, X.; Miodownik, A. P.; Schillé, J.-Ph.

    2003-12-01

    This article describes the development of a new multi-platform software program called JMatPro for calculating the properties and behavior of multi-component alloys. These properties are wide ranging, including thermophysical and physical properties (from room temperature to the liquid state), time-temperature-transformation/continuous-cooling transformation diagrams, stress/strain diagrams, proof and tensile stress, hardness, coarsening of γ' and γ″, and creep. A feature of the new program is that the calculations are based on sound physical principles rather than purely statistical methods. Thus, many of the shortcomings of methods such as regression analysis can be overcome. With this program, sensitivity to microstructure can be included for many of the properties and the true inter-relationship between properties can be developed, for example in the modeling of creep and precipitation hardening.

  13. Modeling Material Properties of Lead-Free Solder Alloys

    Science.gov (United States)

    Guo, Zhanli; Saunders, Nigel; Miodownik, Peter; Schillé, Jean-Philippe

    2008-01-01

    A full set of physical and thermophysical properties for lead-free solder (LFS) alloys have been calculated, including liquidus/solidus temperatures, fraction solid, density, coefficient of thermal expansion, thermal conductivity, Young’s modulus, viscosity, and liquid surface tension, all as a function of composition and temperature (extending into the liquid state). The results have been extensively validated against data available in the literature. A detailed comparison of the properties of two LFS alloys Sn-20In-2.8Ag and Sn-5.5Zn-4.5In-3.5Bi with Sn-37Pb has been made to show the utility and need for calculations that cover a wide range of properties, including the need to consider the effect of nonequilibrium cooling. The modeling of many of these properties follows well-established procedures previously used in JMatPro software for a range of structural alloys. This paper describes an additional procedure for the calculation of the liquid surface tension for multicomponent systems, based on the Butler equation. Future software developments are reviewed, including the addition of mechanical properties, but the present calculations can already make a useful contribution to the selection of appropriate new LFS alloys.

  14. Modeling of Impact Properties of Auxetic Materials: Phase 1

    Science.gov (United States)

    2013-08-01

    underlying metal substrate from impact damage will be determined, and compared to the effect of solid polymer coatings (containing no honeycomb shaped air...higher indentation resistance, higher fracture toughness and greater resistance to impact damage . These unique features of the auxetic materials make... Elastoplasticity of auxetic materials, Computational Material Science, in press. [24] Horrigan, E.J., Smith, C.W., Scarpa, F.L., Gaspar, N., Javadi, A.A

  15. Material Properties from Air Puff Corneal Deformation by Numerical Simulations on Model Corneas

    Science.gov (United States)

    Dorronsoro, Carlos; de la Hoz, Andrés; Marcos, Susana

    2016-01-01

    Objective To validate a new method for reconstructing corneal biomechanical properties from air puff corneal deformation images using hydrogel polymer model corneas and porcine corneas. Methods Air puff deformation imaging was performed on model eyes with artificial corneas made out of three different hydrogel materials with three different thicknesses and on porcine eyes, at constant intraocular pressure of 15 mmHg. The cornea air puff deformation was modeled using finite elements, and hyperelastic material parameters were determined through inverse modeling, minimizing the difference between the simulated and the measured central deformation amplitude and central-peripheral deformation ratio parameters. Uniaxial tensile tests were performed on the model cornea materials as well as on corneal strips, and the results were compared to stress-strain simulations assuming the reconstructed material parameters. Results The measured and simulated spatial and temporal profiles of the air puff deformation tests were in good agreement (< 7% average discrepancy). The simulated stress-strain curves of the studied hydrogel corneal materials fitted well the experimental stress-strain curves from uniaxial extensiometry, particularly in the 0–0.4 range. Equivalent Young´s moduli of the reconstructed material properties from air-puff were 0.31, 0.58 and 0.48 MPa for the three polymer materials respectively which differed < 1% from those obtained from extensiometry. The simulations of the same material but different thickness resulted in similar reconstructed material properties. The air-puff reconstructed average equivalent Young´s modulus of the porcine corneas was 1.3 MPa, within 18% of that obtained from extensiometry. Conclusions Air puff corneal deformation imaging with inverse finite element modeling can retrieve material properties of model hydrogel polymer corneas and real corneas, which are in good correspondence with those obtained from uniaxial extensiometry

  16. Models and simulations of nuclear fuel materials properties

    Energy Technology Data Exchange (ETDEWEB)

    Stan, M. [Los Alamos National Laboratory, PO Box 1663, Los Alamos, NM 87545 (United States)], E-mail: mastan@lanl.gov; Ramirez, J.C. [Los Alamos National Laboratory, PO Box 1663, Los Alamos, NM 87545 (United States); Cristea, P. [University of Bucharest, Faculty of Physics, Bucuresti-Magurele (Romania); Hu, S.Y.; Deo, C.; Uberuaga, B.P.; Srivilliputhur, S.; Rudin, S.P.; Wills, J.M. [Los Alamos National Laboratory, PO Box 1663, Los Alamos, NM 87545 (United States)

    2007-10-11

    To address the complexity of the phenomena that occur in a nuclear fuel element, a multi-scale method was developed. The method incorporates theory-based atomistic and continuum models into finite element simulations to predict heat transport phenomena. By relating micro and nano-scale models to the macroscopic equilibrium and non-equilibrium simulations, the predictive character of the method is improved. The multi-scale approach was applied to calculations of point defect concentration, helium bubbles formation, oxygen diffusivity, and simulations of heat and mass transport in UO{sub 2+x}.

  17. Modeling Spin Testing Using Location Specific Material Properties

    Science.gov (United States)

    2012-04-01

    Three stages of creep. 37 2.4.1 Creep Testing A virtual creep test begins with an elastoplastic coupon, and an initial prescribed...and maximum single crystal Schmid factor. This then models the worst case of a potent damaged inclusion cluster located in a group of grains of high...is the maximum plastic shear strain amplitude, while the coefficient K’ takes into account the damaging effect of the local maximum normal stress

  18. FRAPCON-3: Modifications to fuel rod material properties and performance models for high-burnup application

    Energy Technology Data Exchange (ETDEWEB)

    Lanning, D.D.; Beyer, C.E.; Painter, C.L.

    1997-12-01

    This volume describes the fuel rod material and performance models that were updated for the FRAPCON-3 steady-state fuel rod performance code. The property and performance models were changed to account for behavior at extended burnup levels up to 65 Gwd/MTU. The property and performance models updated were the fission gas release, fuel thermal conductivity, fuel swelling, fuel relocation, radial power distribution, solid-solid contact gap conductance, cladding corrosion and hydriding, cladding mechanical properties, and cladding axial growth. Each updated property and model was compared to well characterized data up to high burnup levels. The installation of these properties and models in the FRAPCON-3 code along with input instructions are provided in Volume 2 of this report and Volume 3 provides a code assessment based on comparison to integral performance data. The updated FRAPCON-3 code is intended to replace the earlier codes FRAPCON-2 and GAPCON-THERMAL-2. 94 refs., 61 figs., 9 tabs.

  19. STUDY OF DYNAMIC MECHANICAL PROPERTIES OF FUSED DEPOSITION MODELLING PROCESSED ULTEM MATERIAL

    OpenAIRE

    Adhiyamaan Arivazhagan; Ammar Saleem; S. H. Masood; Mostafa Nikzad; K. A. JAGADEESH

    2014-01-01

    Fused Deposition Modelling (FDM), a renowned Rapid Prototyping (RP) process, has been successfully implemented in several industries to fabricate concept models and prototypes for rapid manufacturing. This study furnishes terse notes about the material damping properties of FDM made ULTEM samples considering the effect of FDM process parameters. Dynamic Mechanical Analysis (DMA) is carried out using DMA 2980 equipment to study the dynamic response of the FDM material subjected to single canti...

  20. Multiscale Modeling of Carbon/Phenolic Composite Thermal Protection Materials: Atomistic to Effective Properties

    Science.gov (United States)

    Arnold, Steven M.; Murthy, Pappu L.; Bednarcyk, Brett A.; Lawson, John W.; Monk, Joshua D.; Bauschlicher, Charles W., Jr.

    2016-01-01

    Next generation ablative thermal protection systems are expected to consist of 3D woven composite architectures. It is well known that composites can be tailored to achieve desired mechanical and thermal properties in various directions and thus can be made fit-for-purpose if the proper combination of constituent materials and microstructures can be realized. In the present work, the first, multiscale, atomistically-informed, computational analysis of mechanical and thermal properties of a present day - Carbon/Phenolic composite Thermal Protection System (TPS) material is conducted. Model results are compared to measured in-plane and out-of-plane mechanical and thermal properties to validate the computational approach. Results indicate that given sufficient microstructural fidelity, along with lowerscale, constituent properties derived from molecular dynamics simulations, accurate composite level (effective) thermo-elastic properties can be obtained. This suggests that next generation TPS properties can be accurately estimated via atomistically informed multiscale analysis.

  1. MINIMUM SOLID AREA MODELS FOR THE EFFECTIVE PROPERTIES OF POROUS MATERIALS - A REFUTATION

    Directory of Open Access Journals (Sweden)

    Willi Pabst

    2015-09-01

    Full Text Available Minimum solid area (MSA models are popular models for the calculation of the effective properties of porous materials and are frequently used to justify the use of a simple exponential relation for fitting purposes. In this contribution it is shown that MSA models, and the simple exponentials they support, are misleading and should be avoided. In particular, taking Young modulus and conductivity (thermal or electrical as examples, it is shown that MSA models are based on the unjustified (and unjustifiable hypothesis that the relative Young modulus and relative conductivity are identical, and moreover equal to the MSA fraction itself. This claim is generally false for isotropic materials, both random or periodic. Although indeed a very specific case exists in which this claim is true for the properties in one specific direction (viz., extremely anisotropic materials with translational invariance, in this specific case MSA models are redundant, because the relative properties are given exactly by the volume- or area-weighted arithmetic mean. It is shown that the mere existence of non-trivial cross-property relations is incompatible with the existence of MSA models. Finally, it is shown by numerical (finite-element modeling that MSA models provide incorrect results even in the simplest of the cases for which they were originally designed, i.e. for simple cubic packings of partially sintered isometric (initially spherical grains. Therefore, paraphrasing Box, MSA models are not only wrong, but also useless, and should be abandoned.

  2. Numerical evaluation of bulk material properties of dental composites using two-phase finite element models.

    Science.gov (United States)

    Li, Jianying; Li, Haiyan; Fok, Alex S L; Watts, David C

    2012-09-01

    The aim of this study was to numerically evaluate the effects of filler contents and resin properties on the material properties of dental composites utilizing realistic 3D micromechanical finite element models. 3D micromechanical finite element models of dental composites containing irregular fillers with non-uniform sizes were created based on a large-scale, surrogate mixture fabricated from irregularly shaped stones and casting resin. The surrogate mixture was first scanned with a micro-CT scanner, and the images reassembled to produce a 3D finite element model. Different filler fractions were achieved by adjusting the matrix volume while keeping the fillers unchanged. Polymerization shrinkage, Young's modulus, Poisson's ratio and viscosity of the model composites were predicted using the finite element models, and their dependence on the filler fraction and material properties of the resin matrix were considered. Comparison of the numerical predictions with available experimental data and analytical models from the literature was performed. Increased filler fraction resulted in lower material shrinkage, higher Young's modulus, lower Poisson's ratio and higher viscosity in the composite. Predicted shrinkage and Young's modulus agreed well with the experimental data and analytical predictions. The McGee-McCullough model best fit the shrinkage and Young's modulus predicted by the finite element method. However, a new parameter, used as the exponent of the filler fraction, had to be introduced to the McGee-McCullough model to better match the predicted viscosity and Poisson's ratio with those from the finite element analysis. Realistic micro-structural finite element models were successfully applied to study the effects of filler fraction and matrix properties on a wide range of mechanical properties of dental composites with irregular fillers. The results can be used to direct the design of such materials to achieve the desired mechanical properties. Published by

  3. Frequency Response of Synthetic Vocal Fold Models with Linear and Nonlinear Material Properties

    Science.gov (United States)

    Shaw, Stephanie M.; Thomson, Scott L.; Dromey, Christopher; Smith, Simeon

    2014-01-01

    Purpose The purpose of this study was to create synthetic vocal fold models with nonlinear stress-strain properties and to investigate the effect of linear versus nonlinear material properties on fundamental frequency during anterior-posterior stretching. Method Three materially linear and three materially nonlinear models were created and stretched up to 10 mm in 1 mm increments. Phonation onset pressure (Pon) and fundamental frequency (F0) at Pon were recorded for each length. Measurements were repeated as the models were relaxed in 1 mm increments back to their resting lengths, and tensile tests were conducted to determine the stress-strain responses of linear versus nonlinear models. Results Nonlinear models demonstrated a more substantial frequency response than did linear models and a more predictable pattern of F0 increase with respect to increasing length (although range was inconsistent across models). Pon generally increased with increasing vocal fold length for nonlinear models, whereas for linear models, Pon decreased with increasing length. Conclusions Nonlinear synthetic models appear to more accurately represent the human vocal folds than linear models, especially with respect to F0 response. PMID:22271874

  4. On the Use of Biaxial Properties in Modeling Annulus as a Holzapfel-Gasser-Ogden Material

    Directory of Open Access Journals (Sweden)

    Narjes eMomeni Shahraki

    2015-06-01

    Full Text Available Besides the biology, stresses and strains within the tissue greatly influence the location of damage initiation and mode of failure in an intervertebral disc. Finite element models of a functional spinal unit (FSU that incorporate reasonably accurate geometry and appropriate material properties are suitable to investigate such issues. Different material models and techniques have been used to model the anisotropic annulus fibrosus, but the abilities of these models to predict damage initiation in the annulus and to explain clinically observed phenomena are unclear. In this study a hyperelastic anisotropic material model for the annulus with two different sets of material constants, experimentally determined using uniaxial and biaxial loading conditions, were incorporated in a 3D finite element model of a ligamentous FSU. The purpose of the study was to highlight the biomechanical differences (e.g., intradiscal pressure, motion, forces, stresses and strains, etc. due to the dissimilarity between the two sets of material properties (uniaxial and biaxial. Based on the analyses, the biaxial constants simulations resulted in better agreements with the in-vitro and in-vivo data, and thus are more suitable for future damage analysis and failure prediction of the annulus under complex multiaxial loading conditions.

  5. The Homogenized Energy Model (HEM) for Characterizing Polarization and Strains in Hysteretic Ferroelectric Materials: Material Properties and Uniaxial Model Development

    Science.gov (United States)

    2012-01-01

    m3) 1 Introduction Piezoelectric materials exhibit two complementary properties due to their noncentrosymmetric struc- ture: the direct effect in which...by analysis of magnetostriction presented on pages 343–346 of [18] or pages 99–104 of [39]. We let ε̄ denote the spontaneous strain generated by the...on Phase Transitions and the Renormalization Group, Addison-Wesley, Reading, MA, 1992. [26] J. Grindlay, An Introduction to the Phenomenological

  6. Material models and properties in the finite element analysis of knee ligaments: a literature review

    Directory of Open Access Journals (Sweden)

    Fabio eGalbusera

    2014-11-01

    Full Text Available Knee ligaments are elastic bands of soft tissue with a complex microstructure and biomechanics which are critical to determine the kinematics as well as the stress bearing behavior of the knee joint. Their correct implementation in terms of material models and properties is therefore necessary in the development of finite element models of the knee, which has been performed for decades for the investigation of both its basic biomechanics and the development of replacement implants and repair strategies for degenerative and traumatic pathologies. Indeed, a wide range of element types and material models has been used to represent knee ligaments, ranging from elastic unidimensional elements to complex hyperelastic three-dimensional structures with anatomically realistic shapes. This paper systematically reviews literature studies which described finite element models of the knee, and summarizes the approaches which have been used to model the ligaments highlighting their strengths and weaknesses.

  7. Material Models and Properties in the Finite Element Analysis of Knee Ligaments: A Literature Review

    Science.gov (United States)

    Galbusera, Fabio; Freutel, Maren; Dürselen, Lutz; D’Aiuto, Marta; Croce, Davide; Villa, Tomaso; Sansone, Valerio; Innocenti, Bernardo

    2014-01-01

    Knee ligaments are elastic bands of soft tissue with a complex microstructure and biomechanics, which are critical to determine the kinematics as well as the stress bearing behavior of the knee joint. Their correct implementation in terms of material models and properties is therefore necessary in the development of finite element models of the knee, which has been performed for decades for the investigation of both its basic biomechanics and the development of replacement implants and repair strategies for degenerative and traumatic pathologies. Indeed, a wide range of element types and material models has been used to represent knee ligaments, ranging from elastic unidimensional elements to complex hyperelastic three-dimensional structures with anatomically realistic shapes. This paper systematically reviews literature studies, which described finite element models of the knee, and summarizes the approaches, which have been used to model the ligaments highlighting their strengths and weaknesses. PMID:25478560

  8. Optimized constitutive equation of material property based on inverse modeling for aluminum alloy hydroforming simulation

    Institute of Scientific and Technical Information of China (English)

    LANG Li-hui; LI Tao; ZHOU Xian-bin; B. E. KRISTENSEN; J. DANCKERT; K. B. NIELSEN

    2006-01-01

    By using aluminum alloys, the properties of the material in sheet hydroforming were obtained based on the identification of parameters for constitutive models by inverse modeling in which the friction coefficients were also considered in 2D and 3D simulations. With consideration of identified simulation parameters by inverse modeling, some key process parameters including tool dimensions and pre-bulging on the forming processes in sheet hydroforming were investigated and optimized. Based on the optimized parameters, the sheet hydroforming process can be analyzed more accurately to improve the robust design. It proves that the results from simulation based on the identified parameters are in good agreement with those from experiments.

  9. Modelling of Physical, Chemical, and Material Properties of Solid Oxide Fuel Cells

    Directory of Open Access Journals (Sweden)

    Jakub Kupecki

    2015-01-01

    Full Text Available This paper provides a review of modelling techniques applicable for system-level studies to account for physical, chemical, and material properties of solid oxide fuel cells. Functionality of 0D to 3D models is discussed and selected examples are given. Author provides information on typical length scales in evaluation of power systems with solid oxide fuel cells. In each section, proper examples of previous studies done in the field of 0D–3D modelling are recalled and discussed.

  10. A novel stress distribution analytical model of O-ring seals under different properties of materials

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Di; Wang, Shao Ping; Wang, Xing Jian [School of Automation Science and Electrical Engineering, Beihang University, Beijing (China)

    2017-01-15

    The elastomeric O-ring seals have been widely used as sealing elements in hydraulic systems. The sealing performance of O-ring seals is related to stress distribution. The stresses distribution depends on the squeeze rate and internal pressure, and would vary with properties of O-ring seals materials. Thus, in order to study the sealing performance of O-ring seals, it is necessary to describe the analytic relationship between stress distribution and properties of O-ring seals materials. For this purpose, a novel Stress distribution analytical model (SDAM) is proposed in this paper. The analytical model utilizes two stress complex functions to describe the stress distribution of O-ring seals. The proposed SDAM can express not only the analytical relationship between stress distribution and Young’s modulus, but also the one between stress distribution and Poisson’s ratio. Finally, compared results between finite element analysis and the SDAM validate that the proposed model can effectively reveal the stress distribution under different properties for O-ring materials.

  11. Modeling the material properties at the onset of damage initiation in bulk potassium dihydrogen phosphate crystals

    Science.gov (United States)

    Demos, Stavros G.; Feit, Michael D.; Duchateau, Guillaume

    2014-10-01

    A model simulating transient optical properties during laser damage in the bulk of KDP/DKDP crystals is presented. The model was developed and tested using as a benchmark its ability to reproduce the well-documented damage initiation behaviors but most importantly, the salient behavior of the wavelength dependence of the damage threshold. The model involves two phases. During phase I, the model assumes a moderate localized initial absorption that is strongly enhanced during the laser pulse via excited state absorption and thermally driven generation of additional point defects in the surrounding material. The model suggests that during a fraction of the pulse duration, the host material around the defect cluster is transformed into a strong absorber that leads to significant increase of the local temperature. During phase II, the model suggests that the excitation pathway consists mainly of one photon absorption events within a quasicontinuum of short-lived vibronic defect states spanning the band gap that was generated after the initial localized heating of the material due to thermal quenching of the excited state lifetimes. The width of the transition (steps) between different number of photons is governed by the instantaneous temperature, which was estimated using the experimental data. The model also suggests that the critical physical parameter prior to initiation of breakdown is the conduction band electron density. This model, employing very few free parameters, for the first time is able to quantitatively reproduce the wavelength dependence of the damage initiation threshold, and thus provides important insight into the physical processes involved.

  12. Electrical properties of materials

    CERN Document Server

    Solymar, L; Syms, R R A

    2014-01-01

    An informal and highly accessible writing style, a simple treatment of mathematics, and clear guide to applications have made this book a classic text in electrical and electronic engineering. Students will find it both readable and comprehensive. The fundamental ideas relevant to the understanding of the electrical properties of materials are emphasized; in addition, topics are selected in order to explain the operation of devices having applications (or possible future applications) in engineering. The mathematics, kept deliberately to a minimum, is well within the grasp of a second-year student. This is achieved by choosing the simplest model that can display the essential properties of a phenomenom, and then examining the difference between the ideal and the actual behaviour. The whole text is designed as an undergraduate course. However most individual sections are self contained and can be used as background reading in graduate courses, and for interested persons who want to explore advances in microele...

  13. Infarcted Left Ventricles Have Stiffer Material Properties and Lower Stiffness Variation: Three-Dimensional Echo-Based Modeling to Quantify In Vivo Ventricle Material Properties.

    Science.gov (United States)

    Fan, Longling; Yao, Jing; Yang, Chun; Tang, Dalin; Xu, Di

    2015-08-01

    Methods to quantify ventricle material properties noninvasively using in vivo data are of great important in clinical applications. An ultrasound echo-based computational modeling approach was proposed to quantify left ventricle (LV) material properties, curvature, and stress/strain conditions and find differences between normal LV and LV with infarct. Echo image data were acquired from five patients with myocardial infarction (I-Group) and five healthy volunteers as control (H-Group). Finite element models were constructed to obtain ventricle stress and strain conditions. Material stiffening and softening were used to model ventricle active contraction and relaxation. Systolic and diastolic material parameter values were obtained by adjusting the models to match echo volume data. Young's modulus (YM) value was obtained for each material stress-strain curve for easy comparison. LV wall thickness, circumferential and longitudinal curvatures (C- and L-curvature), material parameter values, and stress/strain values were recorded for analysis. Using the mean value of H-Group as the base value, at end-diastole, I-Group mean YM value for the fiber direction stress-strain curve was 54% stiffer than that of H-Group (136.24 kPa versus 88.68 kPa). At end-systole, the mean YM values from the two groups were similar (175.84 kPa versus 200.2 kPa). More interestingly, H-Group end-systole mean YM was 126% higher that its end-diastole value, while I-Group end-systole mean YM was only 29% higher that its end-diastole value. This indicated that H-Group had much greater systole-diastole material stiffness variations. At beginning-of-ejection (BE), LV ejection fraction (LVEF) showed positive correlation with C-curvature, stress, and strain, and negative correlation with LV volume, respectively. At beginning-of-filling (BF), LVEF showed positive correlation with C-curvature and strain, but negative correlation with stress and LV volume, respectively. Using averaged values of two groups

  14. Porous Materials - Structure and Properties

    DEFF Research Database (Denmark)

    Nielsen, Anders

    1997-01-01

    The paper presents some viewpoints on the description of the pore structure and the modelling of the properties of the porous building materials. Two examples are given , where it has been possible to connect the pore structure to the properties: Shrinkage of autoclaved aerated concrete and the p......The paper presents some viewpoints on the description of the pore structure and the modelling of the properties of the porous building materials. Two examples are given , where it has been possible to connect the pore structure to the properties: Shrinkage of autoclaved aerated concrete...

  15. STUDY OF DYNAMIC MECHANICAL PROPERTIES OF FUSED DEPOSITION MODELLING PROCESSED ULTEM MATERIAL

    Directory of Open Access Journals (Sweden)

    Adhiyamaan Arivazhagan

    2014-01-01

    Full Text Available Fused Deposition Modelling (FDM, a renowned Rapid Prototyping (RP process, has been successfully implemented in several industries to fabricate concept models and prototypes for rapid manufacturing. This study furnishes terse notes about the material damping properties of FDM made ULTEM samples considering the effect of FDM process parameters. Dynamic Mechanical Analysis (DMA is carried out using DMA 2980 equipment to study the dynamic response of the FDM material subjected to single cantilever loading under periodic stress. Three FDM process parameters namely Build Style, Raster Width and Raster Angle were contemplated. ULTEM parts are fabricated using solid normal build style and three values each of raster width and raster angle. DMA is performed with temperature sweep at three different fixed frequencies of 1, 50 and 100 Hz. Results were obtained for dynamic properties such as Maximum Storage Modulus, Maximum Loss Modulus, Maximum Tan Delta and Maximum Complex Viscosity. The present work discusses the effect of increasing the frequencies and temperature on FDM made ULTEM samples using different FDM process parameters.

  16. Spin Dynamics simulations of the dynamic properties of classical models for magnetic materials

    Science.gov (United States)

    Bunker, Alex; Landau, D. P.

    1998-03-01

    The Spin Dynamics simulation technique, which has had considerable success for the study of critical properties of classical Heisenberg antiferromagnets(A. Bunker, K. Chen, and D. P. Landau Phys. Rev. B) \\underline54, 9259 (1996), has been used to determine more general properties for a wider range of materials. A general spin dynamics program has been developed which can determine the dynamic structure factor, S(q,ω), in the [100], [110], and [111] directions for a wide range of classical magnetic models at any temperature desired. We have simulated the magnetic dynamics in the ordered phase of the isotropic Heisenberg model with both ferromagnetic and antiferromagnetic coupling on L×L×L BCC and SC lattices. Outside of the critical regime relatively small lattice sizes of L = 12, 24 could be used. From our simulation we have determined the stiffness coefficient and the spin relaxation rate which were compared to both experimental(J. Als-Nielsen in Phase Transitions and Critical Phenomena), ed. C. Domb, M. S. Green, Academic Press, (1976) and theoretical results. We have performed the same simulation with anisotropy appropriate for MnF2 and FeF_2. Research supported in part by the NSF

  17. Study of normal and shear material properties for viscoelastic model of asphalt mixture by discrete element method

    DEFF Research Database (Denmark)

    Feng, Huan; Pettinari, Matteo; Stang, Henrik

    2015-01-01

    In this paper, the viscoelastic behavior of asphalt mixture was studied by using discrete element method. The dynamic properties of asphalt mixture were captured by implementing Burger’s contact model. Different ways of taking into account of the normal and shear material properties of asphalt mi...

  18. Modelling of thermoelectric materials

    DEFF Research Database (Denmark)

    Bjerg, Lasse

    In order to discover new good thermoelectric materials, there are essentially two ways. One way is to go to the laboratory, synthesise a new material, and measure the thermoelectric properties. The amount of compounds, which can be investigated this way is limited because the process is time...... consuming. Another approach is to model the thermoelectric properties of a material on a computer. Several crystal structures can be investigated this way without use of much man power. I have chosen the latter approach. Using density functional theory I am able to calculate the band structure of a material....... This band structure I can then use to calculate the thermoelectric properties of the material. With these results I have investigated several materials and found the optimum theoretical doping concentration. If materials with these doping concentrations be synthesised, considerably better thermoelectric...

  19. Dynamical properties measurements for asteroid, comet and meteorite material applicable to impact modeling and mitigation calculations

    Energy Technology Data Exchange (ETDEWEB)

    Furnish, M.D.; Boslough, M.B. [Sandia National Labs., Albuquerque, NM (United States); Gray, G.T. III [Los Alamos National Lab., NM (United States); Remo, J.L. [Quantametrics, Inc., St. James, NY (United States)

    1994-07-01

    We describe methods for measuring dynamical properties for two material categories of interest in understanding large-scale extraterrestrial impacts: iron-nickel and underdense materials (e.g. snow). Particular material properties measured by the present methods include Hugoniot release paths and constitutive properties (stress vs. strain). The iron-nickel materials lend themselves well to conventional shock and quasi-static experiments. As examples, a suite of experiments is described including six impact tests (wave profile compression/release) over the stress range 2--20 GPa, metallography, quasi-static and split Hopkinson pressure bar (SHPB) mechanical testing, and ultrasonic mapping and sound velocity measurements. Temperature sensitivity of the dynamic behavior was measured at high and low strain rates. Among the iron-nickel materials tested, an octahedrite was found to have behavior close to that of Armco iron under shock and quasi-static conditions, while an ataxite exhibited a significantly larger quasi-static yield strength than did the octahedrite or a hexahedrite. The underdense materials pose three primary experimental difficulties. First, the samples are friable; they can melt or sublimate during storage, preparation and testing. Second, they are brittle and crushable; they cannot withstand such treatment as traditional machining or launch in a gun system. Third, with increasing porosity the calculated Hugoniot density becomes rapidly more sensitive to errors in wave time-of-arrival measurements. Carefully chosen simulants eliminate preservation (friability) difficulties, but the other difficulties remain. A family of 36 impact tests was conducted on snow and snow simulants at Sandia, yielding reliable Hugoniot and reshock states, but limited release property information. Other methods for characterizing these materials are discussed.

  20. Dynamical properties measurements for asteroid, comet and meteorite material applicable to impact modeling and mitigation calculations

    Science.gov (United States)

    Furnish, M. D.; Boslough, M. B.; Gray, G. T., III; Remo, J. L.

    We describe methods for measuring dynamical properties for two material categories of interest in understanding large-scale extraterrestrial impacts: iron-nickel and underdense materials (e.g. snow). Particular material properties measured by the present methods include Hugoniot release paths and constitutive properties (stress vs. strain). The iron-nickel materials lend themselves well to conventional shock and quasi-static experiments. As examples, a suite of experiments is described including six impact tests (wave profile compression/release) over the stress range 2-20 GPa, metallography, quasi-static and split Hopkinson pressure bar (SHPB) mechanical testing, and ultrasonic mapping and sound velocity measurements. Temperature sensitivity of the dynamic behavior was measured at high and low strain rates. Among the iron-nickel materials tested, an octahedrite was found to have behavior close to that of Armco iron under shock and quasi-static conditions, while an ataxite exhibited a significantly larger quasi-static yield strength than did the octahedrite or a hexahedrite. The underdense materials pose three primary experimental difficulties. First, the samples are friable; they can melt or sublimate during storage, preparation and testing. Second, they are brittle and crushable; they cannot withstand such treatment as traditional machining or launch in a gun system. Third, with increasing porosity the calculated Hugoniot density becomes rapidly more sensitive to errors in wave time-of-arrival measurements. Carefully chosen simulants eliminate preservation (friability) difficulties, but the other difficulties remain. A family of 36 impact tests was conducted on snow and snow simulants at Sandia, yielding reliable Hugoniot and reshock states, but limited release property information. Other methods for characterizing these materials are discussed.

  1. The effect of material properties on growth rates of folding and boudinage: Experiments with wax models

    Science.gov (United States)

    Neurath, C.; Smith, R. B.

    The growth of unstable structures was studied experimentally in layered wax models. The rheological properties of the two wax types were determined independently by a series of cylinder compression tests. Both waxes enhibited (1) a non-Newtonian stress vs strain-rate relationship (2) strain softening and (3) temperature-dependent viscosity. The stress-strain-rate relationships approximated a power-law, with stress exponents of 5 for the microcrystalline wax and 1.8 for paraffin wax. Blocks of paraffin with a single embedded layer of microcrystalline wax were deformed in two-dimensional pure shear with the layer oriented either parallel to the compressive strain axis so that it shortened and folded, or perpendicular to that axis so that it would stretch and boundinage would form. The growth rates of tiny initial disturbances were measured. The growth rates for folding and boudinage were much higher than could be accounted for by theories assuming Newtonian material properties. Theories taking non-Newtonian behaviour into account (Smith, R. B. 1975. Bull. geol. Soc. Am.86, 1601-1609; Fletcher, R. C. 1974. Am. J. Sci.274, 1029-1043) better describe the folding growth rates. Boudinage, however, grew almost three times faster than would be predicted even by existing non-Newtonian theory. A possible reason for this discrepancy is that the waxes do not exhibit steady-state creep as assumed in the theory. We, therefore, extend the theory to include strain-softening. The crucial step in this theory is the use of a scalar measure of the deformation as a state variable in the constitutive law. In this way the isotropic manifestation of strain-softening can be taken into account. The analysis shows that strain-softening can lead to greatly increased boudinage growth rates while having little influence on the growth rates of folds, which is in agreement with the experiments.

  2. Mechanism of Exfoliation and Prediction of Materials Properties of Clay-Polymer Nanocomposites from Multiscale Modeling.

    Science.gov (United States)

    Suter, James L; Groen, Derek; Coveney, Peter V

    2015-12-09

    We describe the mechanism that leads to full exfoliation and dispersion of organophilic clays when mixed with molten hydrophilic polymers. This process is of fundamental importance for the production of clay-polymer nanocomposites with enhanced materials properties. The chemically specific nature of our multiscale approach allows us to probe how chemistry, in combination with processing conditions, produces such materials properties at the mesoscale and beyond. In general agreement with experimental observations, we find that a higher grafting density of charged quaternary ammonium surfactant ions promotes exfoliation, by a mechanism whereby the clay sheets slide transversally over one another. We can determine the elastic properties of these nanocomposites; exfoliated and partially exfoliated morphologies lead to substantial enhancement of the Young's modulus, as found experimentally.

  3. Atomistic simulation of nanoporous layered double hydroxide materials and their properties. I. Structural modeling

    Science.gov (United States)

    Kim, Nayong; Kim, Yongman; Tsotsis, Theodore T.; Sahimi, Muhammad

    2005-06-01

    An atomistic model of layered double hydroxides, an important class of nanoporous materials, is presented. These materials have wide applications, ranging from adsorbents for gases and liquid ions to nanoporous membranes and catalysts. They consist of two types of metallic cations that are accommodated by a close-packed configuration of OH- and other anions in a positively charged brucitelike layer. Water and various anions are distributed in the interlayer space for charge compensation. A modified form of the consistent-valence force field, together with energy minimization and molecular dynamics simulations, is utilized for developing an atomistic model of the materials. To test the accuracy of the model, we compare the vibrational frequencies, x-ray diffraction patterns, and the basal spacing of the material, computed using the atomistic model, with our experimental data over a wide range of temperature. Good agreement is found between the computed and measured quantities.

  4. Electromagnetic Nondestructive Evaluation of Wire Insulation and Models of Insulation Material Properties

    Science.gov (United States)

    Bowler, Nicola; Kessler, Michael R.; Li, Li; Hondred, Peter R.; Chen, Tianming

    2012-01-01

    Polymers have been widely used as wiring electrical insulation materials in space/air-craft. The dielectric properties of insulation polymers can change over time, however, due to various aging processes such as exposure to heat, humidity and mechanical stress. Therefore, the study of polymers used in electrical insulation of wiring is important to the aerospace industry due to potential loss of life and aircraft in the event of an electrical fire caused by breakdown of wiring insulation. Part of this research is focused on studying the mechanisms of various environmental aging process of the polymers used in electrical wiring insulation and the ways in which their dielectric properties change as the material is subject to the aging processes. The other part of the project is to determine the feasibility of a new capacitive nondestructive testing method to indicate degradation in the wiring insulation, by measuring its permittivity.

  5. Evaluation of a Multiscale Modelling Methodology to Predict the Mechanical Properties of PCL/β-TCP Sintered Scaffold Materials.

    Science.gov (United States)

    Doyle, Heather; Lohfeld, Stefan; McDonnell, Pat; McHugh, Peter

    2015-08-01

    A multiscale modelling methodology to predict the macroscale stiffness of selective laser sintered polycaprolactone (PCL)/β-tricalcium phosphate (β-TCP) materials is evaluated. The relationship between a micromechanics-evaluated composite material elastic modulus (E eff) and segment grey-value (GVave) is established for a 90/10 wt% PCL/β-TCP material and compared to the previously established E eff vs. GVave relationship for a 50/50 wt% PCL/β-TCP material. The increase in E eff with GVave was found to be greater for the 90/10 wt% material than for the 50/50 wt% material. Differences in the material microstructures are visible with greater local conglomerations of β-TCP in the 90/10 wt% material compared to the 50/50 wt% material. These results indicate that the relationship between E eff and GVave is material-specific and that one definition cannot be used to describe both materials. We have used the E eff and GVave relationship specific to the 90/10 wt% material to assign element-specific elastic properties in a high resolution macroscale strut finite element model to successfully predict the experimentally-evaluated strut effective stiffness of the 90/10 wt%. These results combined indicate that this multiscale modelling methodology reasonably predicts the effective elastic modulus of selective laser sintering struts with different material configurations, and that it can be used to determine the material-specific definition of the relationship between E eff and GVave for a particular material.

  6. Chemical modeling of acid-base properties of soluble biopolymers derived from municipal waste treatment materials.

    Science.gov (United States)

    Tabasso, Silvia; Berto, Silvia; Rosato, Roberta; Marinos, Janeth Alicia Tafur; Ginepro, Marco; Zelano, Vincenzo; Daniele, Pier Giuseppe; Montoneri, Enzo

    2015-02-04

    This work reports a study of the proton-binding capacity of biopolymers obtained from different materials supplied by a municipal biowaste treatment plant located in Northern Italy. One material was the anaerobic fermentation digestate of the urban wastes organic humid fraction. The others were the compost of home and public gardening residues and the compost of the mix of the above residues, digestate and sewage sludge. These materials were hydrolyzed under alkaline conditions to yield the biopolymers by saponification. The biopolymers were characterized by 13C NMR spectroscopy, elemental analysis and potentiometric titration. The titration data were elaborated to attain chemical models for interpretation of the proton-binding capacity of the biopolymers obtaining the acidic sites concentrations and their protonation constants. The results obtained with the models and by NMR spectroscopy were elaborated together in order to better characterize the nature of the macromolecules. The chemical nature of the biopolymers was found dependent upon the nature of the sourcing materials.

  7. An ongoing investigation on modeling the strength properties of water-entrained cement-based materials

    DEFF Research Database (Denmark)

    Esteves, L.P.

    2012-01-01

    Water-entrained cement based materials by superabsorbent polymers is a concept that was introduced in the research agenda about a decade ago. However, a recent application in the production of high performance concrete revealed potential weaknesses when the proportioning of this intelligent...... material is not well performed, raising doubts among both academic and industrial society about the usability of superabsorbent polymers in cement-based materials. This work constitutes the baseline tentatively to be used on modeling the compressive strength of SF-modified water-entrained cement...

  8. Perspective: Web-based machine learning models for real-time screening of thermoelectric materials properties

    Science.gov (United States)

    Gaultois, Michael W.; Oliynyk, Anton O.; Mar, Arthur; Sparks, Taylor D.; Mulholland, Gregory J.; Meredig, Bryce

    2016-05-01

    The experimental search for new thermoelectric materials remains largely confined to a limited set of successful chemical and structural families, such as chalcogenides, skutterudites, and Zintl phases. In principle, computational tools such as density functional theory (DFT) offer the possibility of rationally guiding experimental synthesis efforts toward very different chemistries. However, in practice, predicting thermoelectric properties from first principles remains a challenging endeavor [J. Carrete et al., Phys. Rev. X 4, 011019 (2014)], and experimental researchers generally do not directly use computation to drive their own synthesis efforts. To bridge this practical gap between experimental needs and computational tools, we report an open machine learning-based recommendation engine (http://thermoelectrics.citrination.com) for materials researchers that suggests promising new thermoelectric compositions based on pre-screening about 25 000 known materials and also evaluates the feasibility of user-designed compounds. We show this engine can identify interesting chemistries very different from known thermoelectrics. Specifically, we describe the experimental characterization of one example set of compounds derived from our engine, RE12Co5Bi (RE = Gd, Er), which exhibits surprising thermoelectric performance given its unprecedentedly high loading with metallic d and f block elements and warrants further investigation as a new thermoelectric material platform. We show that our engine predicts this family of materials to have low thermal and high electrical conductivities, but modest Seebeck coefficient, all of which are confirmed experimentally. We note that the engine also predicts materials that may simultaneously optimize all three properties entering into zT; we selected RE12Co5Bi for this study due to its interesting chemical composition and known facile synthesis.

  9. Perspective: Web-based machine learning models for real-time screening of thermoelectric materials properties

    Directory of Open Access Journals (Sweden)

    Michael W. Gaultois

    2016-05-01

    Full Text Available The experimental search for new thermoelectric materials remains largely confined to a limited set of successful chemical and structural families, such as chalcogenides, skutterudites, and Zintl phases. In principle, computational tools such as density functional theory (DFT offer the possibility of rationally guiding experimental synthesis efforts toward very different chemistries. However, in practice, predicting thermoelectric properties from first principles remains a challenging endeavor [J. Carrete et al., Phys. Rev. X 4, 011019 (2014], and experimental researchers generally do not directly use computation to drive their own synthesis efforts. To bridge this practical gap between experimental needs and computational tools, we report an open machine learning-based recommendation engine (http://thermoelectrics.citrination.com for materials researchers that suggests promising new thermoelectric compositions based on pre-screening about 25 000 known materials and also evaluates the feasibility of user-designed compounds. We show this engine can identify interesting chemistries very different from known thermoelectrics. Specifically, we describe the experimental characterization of one example set of compounds derived from our engine, RE12Co5Bi (RE = Gd, Er, which exhibits surprising thermoelectric performance given its unprecedentedly high loading with metallic d and f block elements and warrants further investigation as a new thermoelectric material platform. We show that our engine predicts this family of materials to have low thermal and high electrical conductivities, but modest Seebeck coefficient, all of which are confirmed experimentally. We note that the engine also predicts materials that may simultaneously optimize all three properties entering into zT; we selected RE12Co5Bi for this study due to its interesting chemical composition and known facile synthesis.

  10. Satellite material contaminant optical properties

    Science.gov (United States)

    Wood, B. E.; Bertrand, W. T.; Seiber, B. L.; Kiech, E. L.; Falco, P. M.; Holt, J. D.

    1990-03-01

    The Air Force Wright Research and Development Center and the Arnold Engineering Development Center are continuing a program for measuring optical effects of satellite material outgassing products on cryo-optic surfaces. Presented here are infrared (4000 to 700 cm(-1)) transmittance data for contaminant films condensed on a 77 K germanium window. From the transmittance data, the contaminant film refractive and absorptive indices (n, k) were derived using an analytical thin-film interference model with a nonlinear least-squares algorithm. To date 19 materials have been studied with the optical contents determined for 13 of those. The materials include adhesives, paints, composites, films, and lubricants. This program is continuing and properties for other materials will be available in the future.

  11. Soft Tissue Finite Element Modeling and Calibration of the Material Properties in the Context of Computer-Assisted Medical Interventions

    OpenAIRE

    Payan, Yohan

    2016-01-01

    International audience; This chapter aims at illustrating how patient-specific models of human organs / soft tissues can be implemented into Finite Element (FE) packages. First is addressed the question of the generation of patient-specific FE models compatible with the clinical constraints. Then is discussed the calibration of the material properties, with choices that should be done between calibrations based on ex vivo or in vivo tissues loadings. The example of computer assisted maxillofa...

  12. An ongoing investigation on modeling the strength properties of water-entrained cement-based materials

    DEFF Research Database (Denmark)

    Esteves, L.P.

    2012-01-01

    -based materials. Beyond the discussion of whether or not the introduction of superabsorbent polymers leads to a strength reduction, this paper uses both experimental and theoretical background to separate the effect of SAP in both pore structure and internal relative humidity and the effect from the active......Water-entrained cement based materials by superabsorbent polymers is a concept that was introduced in the research agenda about a decade ago. However, a recent application in the production of high performance concrete revealed potential weaknesses when the proportioning of this intelligent...... material is not well performed, raising doubts among both academic and industrial society about the usability of superabsorbent polymers in cement-based materials. This work constitutes the baseline tentatively to be used on modeling the compressive strength of SF-modified water-entrained cement...

  13. Full-band structure modeling of the radiative and non-radiative properties of semiconductor materials and devices (Presentation Recording)

    Science.gov (United States)

    Bellotti, Enrico; Wen, Hanqing; Pinkie, Benjamin; Matsubara, Masahiko; Bertazzi, Francesco

    2015-08-01

    Understanding the radiative and non-radiative properties of semiconductor materials is a prerequisite for optimizing the performance of existing light emitters and detectors and for developing new device architectures based on novel materials. Due to the ever increasing complexity of novel semiconductor systems and their relative technological immaturity, it is essential to have design tools and simulation strategies that include the details of the microscopic physics and their dependence on the macroscopic (continuum) variables in the macroscopic device models. Towards this end, we have developed a robust full-band structure based approach that can be used to study the intrinsic material radiative and non-radiative properties and evaluate the same characteristics of low-dimensional device structures. A parallel effort is being carried out to model the effect of substrate driven stress/strain and material quality (dislocations and defects) on microscopic quantities such as non-radiative recombination rate. Using this modeling approach, we have extensively studied the radiative and non-radiative properties of both elemental (Si and Ge) and compound semiconductors (HgCdTe, InGaAs, InAsSb and InGaN). In this work we outline the details of the modelling approach, specifically the challenges and advantages related to the use of the full-band description of the material electronic structure. We will present a detailed comparison of the radiative and Auger recombination rates as a function of temperature and doping for HgCdTe and InAsSb that are two important materials for infrared detectors and emitters. Furthermore we will discuss the role of non-radiatiave Auger recombination processes in explaining the performance of light emitter diodes. Finally we will present the extension of the model to low dimensional structures employed in a number of light emitter and detector structures.

  14. Chemical Modeling of Acid-Base Properties of Soluble Biopolymers Derived from Municipal Waste Treatment Materials

    Science.gov (United States)

    Tabasso, Silvia; Berto, Silvia; Rosato, Roberta; Tafur Marinos, Janeth Alicia; Ginepro, Marco; Zelano, Vincenzo; Daniele, Pier Giuseppe; Montoneri, Enzo

    2015-01-01

    This work reports a study of the proton-binding capacity of biopolymers obtained from different materials supplied by a municipal biowaste treatment plant located in Northern Italy. One material was the anaerobic fermentation digestate of the urban wastes organic humid fraction. The others were the compost of home and public gardening residues and the compost of the mix of the above residues, digestate and sewage sludge. These materials were hydrolyzed under alkaline conditions to yield the biopolymers by saponification. The biopolymers were characterized by 13C NMR spectroscopy, elemental analysis and potentiometric titration. The titration data were elaborated to attain chemical models for interpretation of the proton-binding capacity of the biopolymers obtaining the acidic sites concentrations and their protonation constants. The results obtained with the models and by NMR spectroscopy were elaborated together in order to better characterize the nature of the macromolecules. The chemical nature of the biopolymers was found dependent upon the nature of the sourcing materials. PMID:25658795

  15. Chemical Modeling of Acid-Base Properties of Soluble Biopolymers Derived from Municipal Waste Treatment Materials

    Directory of Open Access Journals (Sweden)

    Silvia Tabasso

    2015-02-01

    Full Text Available This work reports a study of the proton-binding capacity of biopolymers obtained from different materials supplied by a municipal biowaste treatment plant located in Northern Italy. One material was the anaerobic fermentation digestate of the urban wastes organic humid fraction. The others were the compost of home and public gardening residues and the compost of the mix of the above residues, digestate and sewage sludge. These materials were hydrolyzed under alkaline conditions to yield the biopolymers by saponification. The biopolymers were characterized by 13C NMR spectroscopy, elemental analysis and potentiometric titration. The titration data were elaborated to attain chemical models for interpretation of the proton-binding capacity of the biopolymers obtaining the acidic sites concentrations and their protonation constants. The results obtained with the models and by NMR spectroscopy were elaborated together in order to better characterize the nature of the macromolecules. The chemical nature of the biopolymers was found dependent upon the nature of the sourcing materials.

  16. Modeling of molecular properties

    CERN Document Server

    Comba, Peter

    2011-01-01

    Molecular modeling encompasses applied theoretical approaches and computational techniques to model structures and properties of molecular compounds and materials in order to predict and / or interpret their properties. The modeling covered in this book ranges from methods for small chemical to large biological molecules and materials. With its comprehensive coverage of important research fields in molecular and materials science, this is a must-have for all organic, inorganic and biochemists as well as materials scientists interested in applied theoretical and computational chemistry. The 28

  17. Numerical Modeling of Thermoelectric Generators with Varing Material Properties in a Circuit Simulator

    DEFF Research Database (Denmark)

    Chen, Min; Rosendahl, Lasse; Condra, Thomas

    2009-01-01

    -compatible environment. This model of thermoelectric battery accounts for all temperature-dependent characteristics of the thermoelectric materials to include the nonlinear voltage, current, and electrothermal coupled effects. It is validated with simulation data from the recognized program ANSYS and experimental data......When a thermoelectric generator (TEG) and its external load circuitry are considered together as a system, the codesign and cooptimization of the electronics and the device are crucial in maximizing the system efficiency. In this paper, an accurate TEG model is proposed and implemented in a SPICE...... from a real thermoelectric device, respectively.Within a common circuit simulator, the model can be easily connected to various electrical models of applied loads to predict and optimize the system performance....

  18. Energy-based constitutive modelling of local material properties of canine aortas

    Science.gov (United States)

    Shahmirzadi, Danial; Acosta, Camilo J.; Konofagou, Elisa

    2016-01-01

    This study aims at determining the in vitro anisotropic mechanical behaviour of canine aortic tissue. We specifically focused on spatial variations of these properties along the axis of the vessel. We performed uniaxial stretch tests on canine aortic samples in both circumferential and longitudinal directions, as well as histological examinations to derive the tissue's fibre orientations. We subsequently characterized a constitutive model that incorporates both phenomenological and structural elements to account for macroscopic and microstructural behaviour of the tissue. We showed the two fibre families were oriented at similar angles with respect to the aorta's axis. We also found significant changes in mechanical behaviour of the tissue as a function of axial position from proximal to distal direction: the fibres become more aligned with the aortic axis from 46° to 30°. Also, the linear shear modulus of media decreased as we moved distally along the aortic axis from 139 to 64 kPa. These changes derived from the parameters in the nonlinear constitutive model agreed well with the changes in tissue structure. In addition, we showed that isotropic contribution, carried by elastic lamellae, to the total stress induced in the tissue decreases at higher stretch ratios, whereas anisotropic stress, carried by collagen fibres, increases. The constitutive models can be readily used to design computational models of tissue deformation during physiological loading cycles. The findings of this study extend the understanding of local mechanical properties that could lead to region-specific diagnostics and treatment of arterial diseases. PMID:27703701

  19. Evaluation of Fatigue Crack Growth and Fracture Properties of Cryogenic Model Materials

    Science.gov (United States)

    Newman, John A.; Forth, Scott C.; Everett, Richard A., Jr.; Newman, James C., Jr.; Kimmel, William M.

    2002-01-01

    The criteria used to prevent failure of wind-tunnel models and support hardware were revised as part of a project to enhance the capabilities of cryogenic wind tunnel testing at NASA Langley Research Center. Specifically, damage-tolerance fatigue life prediction methods are now required for critical components, and material selection criteria are more general and based on laboratory test data. The suitability of two candidate model alloys (AerMet 100 and C-250 steel) was investigated by obtaining the fatigue crack growth and fracture data required for a damage-tolerance fatigue life analysis. Finally, an example is presented to illustrate the newly implemented damage tolerance analyses required of wind-tunnel model system components.

  20. Analytical applications and effective properties of a second gradient isotropic elastic material model

    Science.gov (United States)

    Enakoutsa, Koffi

    2015-06-01

    Recently, the works by Toupin, Mindlin, Sokolowski and Germain have been developed following two research streams. In the first one, higher-order gradient continuum models were developed based on the Cauchy tetrahedron argument (see, e.g., dell'Isola and Seppecher in Comptes Rendus de l Academie de Sciences 17 Serie IIb: Mecanique, Physique, Chimie, Astronomie 321:303-308, 1995, Meccanica 32:33-52 1997, Zeitschrift fr Angewandte Mathematik und Physik 63(6):1119-1141, 2012). In the second one, the structure of higher-order gradient models is developed with a view to the applications. In particular in the model of linear isotropic solids proposed by Dell'Isola, Sciarra and Vidoli (DSV), the main constitutive equation is obtained for the case of second gradient models. This model introduces in addition to the two well-known Lame's elastic constants five constitutive constants. The practical applications of this model remain in its infancy since the issue of determining the new moduli it introduces is not yet completely addressed. Also, analytical solutions of simple boundary value problems that can be helpful to grasp some of the physical foundations of this model are missing. This paper aims to address these two issues by providing the analytical solutions for two model problems, a spherical shell subjected to axisymmetric loading conditions and the circular bending of a beam in plane strain, both the beam and the shell obeying the DSV second gradient isotropic elastic model. The solution of the circular bending of a beam has served to grasp some of the physical soundness of the model. A framework based on homogenization under inhomogeneous boundary conditions is also suggested to determine the unknown constitutive constants, which are provided in the particular case of elastic porous heterogeneous materials.

  1. Predicting the elastic properties of selective laser sintered PCL/β-TCP bone scaffold materials using computational modelling.

    Science.gov (United States)

    Doyle, Heather; Lohfeld, Stefan; McHugh, Peter

    2014-03-01

    This study assesses the ability of finite element (FE) models to capture the mechanical behaviour of sintered orthopaedic scaffold materials. Individual scaffold struts were fabricated from a 50:50 wt% poly-ε-caprolactone (PCL)/β-tricalcium phosphate (β-TCP) blend, using selective laser sintering. The tensile elastic modulus of single struts was determined experimentally. High resolution FE models of single struts were generated from micro-CT scans (28.8 μm resolution) and an effective strut elastic modulus was calculated from tensile loading simulations. Three material assignment methods were employed: (1) homogeneous PCL elastic constants, (2) composite PCL/β-TCP elastic constants based on rule of mixtures, and (3) heterogeneous distribution of micromechanically-determined elastic constants. In comparison with experimental results, the use of homogeneous PCL properties gave a good estimate of strut modulus; however it is not sufficiently representative of the real material as it neglects the β-TCP phase. The rule of mixtures method significantly overestimated strut modulus, while there was no significant difference between strut modulus evaluated using the micromechanically-determined elastic constants and experimentally evaluated strut modulus. These results indicate that the multi-scale approach of linking micromechanical modelling of the sintered scaffold material with macroscale modelling gives an accurate prediction of the mechanical behaviour of the sintered structure.

  2. Optical properties of advanced materials

    CERN Document Server

    Kajikawa, Kotaro

    2013-01-01

    In the last decade, optically functionalized materials have developed rapidly, from bulk matters to structured forms. Now we have a rich variety of attractive advanced materials. They are applied to optical and electrical devices that support the information communication technology in the mid 21-th century. Accordingly, it is quite important to have a broad knowledge of the optical properties of advanced materials for students, scientists and engineers working in optics and related fields. This book is designed to teach fundamental optical properties of such advanced materials effectively. These materials have their own peculiarities which are very interesting in modern optical physics and also for applications because the concepts of optical properties are quite different from those in conventional optical materials. Hence each chapter starts to review the basic concepts of the materials briefly and proceeds to the practical use. The important topics covered in this book include:  quantum structures of sem...

  3. Multiscale Lattice Boltzmann-Finite Element Modelling of Transport Properties in Cement-based Materials

    NARCIS (Netherlands)

    Zhang, M.

    2013-01-01

    Cement-based materials are the most widely used man-made materials in the world. The durability of cement-based materials has been a major concern due to the premature failure and serviceability issues of many reinforced concrete structures. Durability of cement-based materials is to a large content

  4. Multiscale Lattice Boltzmann-Finite Element Modelling of Transport Properties in Cement-based Materials

    NARCIS (Netherlands)

    Zhang, M.

    2013-01-01

    Cement-based materials are the most widely used man-made materials in the world. The durability of cement-based materials has been a major concern due to the premature failure and serviceability issues of many reinforced concrete structures. Durability of cement-based materials is to a large content

  5. An Overview of Mechanical Properties and Material Modeling of Polylactide (PLA) for Medical Applications.

    Science.gov (United States)

    Bergström, Jörgen S; Hayman, Danika

    2016-02-01

    This article provides an overview of the connection between the microstructural state and the mechanical response of various bioresorbable polylactide (PLA) devices for medical applications. PLLA is currently the most commonly used material for bioresorbable stents and sutures, and its use is increasing in many other medical applications. The non-linear mechanical response of PLLA, due in part to its low glass transition temperature (T g ≈ 60 °C), is highly sensitive to the molecular weight and molecular orientation field, the degree of crystallinity, and the physical aging time. These microstructural parameters can be tailored for specific applications using different resin formulations and processing conditions. The stress-strain, deformation, and degradation response of a bioresorbable medical device is also strongly dependent on the time history of applied loads and boundary conditions. All of these factors can be incorporated into a suitable constitutive model that captures the multiple physics that are involved in the device response. Currently developed constitutive models already provide powerful computations simulation tools, and more progress in this area is expected to occur in the coming years.

  6. Dental materials with antibiofilm properties.

    Science.gov (United States)

    Wang, Zhejun; Shen, Ya; Haapasalo, Markus

    2014-02-01

    Oral bacteria have evolved to form biofilms on hard tooth surfaces and dental materials. The antibiofilm effect of materials used for the restoration of oral function affects oral health. In this review we describe the features involved in the formation of oral biofilms on different surfaces in the oral cavity and the antibiofilm properties of dental materials. An electronic search of scientific papers from 1987 to 2013 was performed with PubMed, ScienceDirect and Google search engines using the following search terms: antibiofilm, dental material, dental hard tissue, endodontic material, implant material, oral biofilm, and restorative material. Selected inclusion criteria resulted in 179 citations from the scientific, peer-reviewed literature. Oral biofilms form not only on dental hard tissue, but also on a wide range of dental materials used in cariology, endodontics, restorative dentistry and periodontology, resulting in destruction of dental hard tissue and even infection. Therefore, there has been a continuous effort to develop the antibiofilm properties of dental materials used for different purposes. Specific antimicrobial design in the composition and application of new materials (e.g. bioceramic sealer, resin composite, implant coating) demonstrates an improvement of the antibiofilm properties of these materials compared to earlier generations. A significant number of dental materials have been shown to affect biofilm growth by inhibiting the adhesion of bacteria, limiting their growth or killing microbes in the biofilms formed in vitro. Incorporation of an appropriate amount of antibacterial agent could provide dental materials with antibiofilm activity without significantly influencing their mechanical properties. However, more randomized and double-blind clinical studies of sufficient length with these materials are needed to confirm long term success following their use in the dental clinic. Copyright © 2013 Academy of Dental Materials. Published by

  7. Materials Analysis and Modeling of Underfill Materials.

    Energy Technology Data Exchange (ETDEWEB)

    Wyatt, Nicholas B [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Chambers, Robert S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-08-01

    The thermal-mechanical properties of three potential underfill candidate materials for PBGA applications are characterized and reported. Two of the materials are a formulations developed at Sandia for underfill applications while the third is a commercial product that utilizes a snap-cure chemistry to drastically reduce cure time. Viscoelastic models were calibrated and fit using the property data collected for one of the Sandia formulated materials. Along with the thermal-mechanical analyses performed, a series of simple bi-material strip tests were conducted to comparatively analyze the relative effects of cure and thermal shrinkage amongst the materials under consideration. Finally, current knowledge gaps as well as questions arising from the present study are identified and a path forward presented.

  8. NATO Advanced Study Institute on Engineering of Crystalline Materials Properties : State of the Art in Modeling Design and Applications. New Materials for better Defence and Security

    CERN Document Server

    Braga, Dario; Addadi, Lia

    2008-01-01

    This volume collects the lecture notes (ordered alphabetically according to the first author surname) of the talks delivered by the main speakers at the Erice 2007 International School of Crystallography, generously selected by NATO as an Advanced Study Institute (# 982582). The aim of the school was to discuss the state-of-the-art in molecular materials design, that is, the rational analysis and fabrication of crystalline solids showing a predefined structural organization of their component molecules and ions, which results in the manifestation of a specific collective property of technological interest. The School was held on June 7–17, 2007, in Erice (an old town, over 3000 years, located on the top of a Sicilian hill that oversees the sea near Trapani). The school developed following two parallel lines. First we established “where we are” in terms of modelling, design, synthesis and applications of crystalline solids with predefined properties. Second, we attempted to define current and possible fu...

  9. Materials with complex behaviour II properties, non-classical materials and new technologies

    CERN Document Server

    Oechsner, Andreas

    2012-01-01

    This book reviews developments and trends in advanced materials and their properties; modeling and simulation of non-classical materials and new technologies for joining materials. Offers tools for characterizing and predicting properties and behavior.

  10. Chemically specific multiscale modeling of clay-polymer nanocomposites reveals intercalation dynamics, tactoid self-assembly and emergent materials properties.

    Science.gov (United States)

    Suter, James L; Groen, Derek; Coveney, Peter V

    2015-02-01

    A quantitative description is presented of the dynamical process of polymer intercalation into clay tactoids and the ensuing aggregation of polymer-entangled tactoids into larger structures, obtaining various characteristics of these nanocomposites, including clay-layer spacings, out-of-plane clay-sheet bending energies, X-ray diffractograms, and materials properties. This model of clay-polymer interactions is based on a three-level approach, which uses quantum mechanical and atomistic descriptions to derive a coarse-grained yet chemically specific representation that can resolve processes on hitherto inaccessible length and time scales. The approach is applied to study collections of clay mineral tactoids interacting with two synthetic polymers, poly(ethylene glycol) and poly(vinyl alcohol). The controlled behavior of layered materials in a polymer matrix is centrally important for many engineering and manufacturing applications. This approach opens up a route to computing the properties of complex soft materials based on knowledge of their chemical composition, molecular structure, and processing conditions. © 2014 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Material Properties at Low Temperature

    CERN Document Server

    Duthil, P

    2014-01-01

    From ambient down to cryogenic temperatures, the behaviour of materials changes greatly. Mechanisms leading to variations in electrical, thermal, mechanical, and magnetic properties in pure metals, alloys, and insulators are briefly introduced from a general engineering standpoint. Data sets are provided for materials commonly used in cryogenic systems for design purposes.

  12. Mechanical Properties of Materials

    CERN Document Server

    Pelleg, Joshua

    2013-01-01

    The subject of mechanical behavior has been in the front line of basic studies in engineering curricula for many years.  This textbook was written for engineering students with the aim of presenting, in a relatively simple manner, the basic concepts of mechanical behavior in solid materials. A second aim of the book is to guide students in their laboratory experiments by helping them to understand their observations in parallel with the lectures of their various courses; therefore the first chapter of the book is devoted to mechanical testing. Another aim of the book is to provide practicing engineers with basic help to bridge the gap of time that has passed from their graduation up to their actual involvement in engineering work. The book also serves as the basis for more advanced studies and seminars when pursuing courses on a graduate level. The content of this textbook and the topics discussed correspond to courses that are usually taught in universities and colleges all over the world, but with a differ...

  13. Finite Element Modeling of CNS White Matter Kinematics: Use of a 3D-RVE to Determine Material Properties

    Directory of Open Access Journals (Sweden)

    Yi ePan

    2013-12-01

    Full Text Available Axonal injury represents a critical target area for the prevention and treatment of traumatic brain and spinal cord injuries. Finite element (FE models of the head and/or brain are often used to predict brain injury caused by external mechanical loadings, such as explosive waves and direct impact. The accuracy of these numerical models depends on correctly determining the material properties and on the precise depiction of the tissues’ microstructure (microscopic level. Moreover, since the axonal microstructure for specific regions of the brain white matter is locally oriented, the stress and strain fields are highly anisotropic and axon orientation dependent. Additionally, mechanical strain has been identified as the proximal cause of axonal injury, which further demonstrates the importance of this multi-scale relationship. In this study, our previously developed FE and kinematic axonal models are coupled and applied to a pseudo 3-dimensional representative volume element (RVE of central nervous system white matter to investigate the multi-scale mechanical behavior. An inverse FE procedure was developed to identify material parameters of spinal cord white matter by combining the results of uniaxial testing with FE modeling. A satisfactory balance between simulation and experiment was achieved via optimization by minimizing the squared error between the simulated and experimental force-stretch curve. The combination of experimental testing and FE analysis provides a useful analysis tool for soft biological tissues in general, and specifically enables evaluations of the axonal response to tissue-level loading and subsequent predictions of axonal damage.

  14. Material properties and modeling characteristics for MnFeP1-xAsx materials for application in magnetic refrigeration

    DEFF Research Database (Denmark)

    Engelbrecht, Kurt; Nielsen, Kaspar Kirstein; Bahl, Christian R.H.

    2013-01-01

    properties. Different methods of building property functions from the measured specific heat, magnetization, and adiabatic temperature change are presented. It is shown that model predictions can be highly dependent on how the properties that are used by the AMR model are calculated. © 2013 AIP Publishing...

  15. An experimentally verified model for thermal microactuators including nonlinear material properties, vacuum, and intra-device heat conduction

    Science.gov (United States)

    Colbert, Keegan; Naraghi, Mohammad; Boyd, James G.

    2017-02-01

    This paper presents a model and computational method to predict the steady-state performance of thermal flexure microactuators at high input powers and various levels of partial vacuum. The model accounts for nonlinear temperature dependence of material properties, heat loss due to radiation, and intra-device heat transfer by conduction across an air gap. The model is validated by comparing the model predictions with the experimentally measured voltage, current, and displacement at standard conditions, prior to adjusting for partial vacuum. In order to understand the effect of nonlinearities on model reliability, the predictions of six additional hypothetical models are considered where (1) intra-device heat transfer is neglected, (2) radiation is neglected, (3) the thermal conductivity of silicon is assumed to be temperature-independent, (4) the thermal conductivity of air is assumed to be temperature-independent, (5) the electrical resistivity of silicon is assumed to be linear in temperature, and (6) the thermal expansion coefficient of silicon is assumed to be temperature-independent. All factors except radiation were shown to have a significant influence on the device performance especially at high input powers. The experimentally validated full model is then employed to predict the effect of reduced air pressure on the displacement and heat transfer properties of the actuator. This aspect of the study targets applications of thermal actuators in controlled environments such as space applications, actuators used for in situ micropositioning and tensile testing inside electron microscopy chambers, or actuators incorporated into the design of MEMS resonators. It was demonstrated that the maximum actuator displacement is not a linear function of reduced pressure and that it reaches a maximum at a certain partial vacuum level.

  16. Mathematical Modeling of Phenomenological Material Properties – Differential Operator Forms of Constitutive Equations

    Directory of Open Access Journals (Sweden)

    Minárová Mária

    2014-12-01

    Full Text Available The paper deals with rheological models and creep and relaxation tests on matters which are represented by models. Three models based on two fundamental components (Hooke’s elastic and Newton’s viscous compounds are performed. The models originated from several fundamental matters by their parallel or serial connections. The corresponding constitutive equations are derived. The behavior of the models under the creep and relaxation tests is observed and is expressed by corresponding stress - strain formulas and illustrated in the figures.

  17. Multiscale Modeling of the Effects of Salt and Perfume Raw Materials on the Rheological Properties of Commercial Threadlike Micellar Solutions.

    Science.gov (United States)

    Tang, Xueming; Zou, Weizhong; Koenig, Peter H; McConaughy, Shawn D; Weaver, Mike R; Eike, David M; Schmidt, Michael J; Larson, Ronald G

    2017-03-23

    We link micellar structures to their rheological properties for two surfactant body-wash formulations at various concentrations of salts and perfume raw materials (PRMs) using molecular simulations and micellar-scale modeling, as well as traditional surfactant packing arguments. The two body washes, namely, BW-1EO and BW-3EO, are composed of sodium lauryl ethylene glycol ether sulfate (SLEnS, where n is the average number of ethylene glycol repeat units), cocamidopropyl betaine (CAPB), ACCORD (which is a mixture of six PRMs), and NaCl salt. BW-3EO is an SLE3S-based body wash, whereas BW-1EO is an SLE1S-based body wash. Additional PRMs are also added into the body washes. The effects of temperature, salt, and added PRMs on micellar lengths, breakage times, end-cap free energies, and other properties are obtained from fits of the rheological data to predictions of the "Pointer Algorithm" [ Zou , W. ; Larson , R.G. J. Rheol. 2014 , 58 , 1 - 41 ], which is a simulation method based on the Cates model of micellar dynamics. Changes in these micellar properties are interpreted using the Israelachvili surfactant packing argument. From coarse-grained molecular simulations, we infer how salt modifies the micellar properties by changing the packing between the surfactant head groups, with the micellar radius remaining nearly constant. PRMs do so by partitioning to different locations within the micelles according to their octanol/water partition coefficient POW and chemical structures, adjusting the packing of the head and/or tail groups, and by changing the micelle radius, in the case of a large hydrophobic PRM. We find that relatively hydrophilic PRMs with log POW 4, are isolated deep inside the micelle, separating from the tails and swelling the radius of the micelle, leading to shorter micelles and much lower viscosities, leading eventually to swollen-droplet micelles.

  18. Material properties in complement activation

    DEFF Research Database (Denmark)

    Moghimi, S. Moein; Andersen, Alina Joukainen; Ahmadvand, Davoud

    2011-01-01

    -immune performance’ relationship studies in nanomedicine research at many fronts. The interaction between nanomaterials and the complement system is complex and regulated by inter-related factors that include nanoscale size, morphology and surface characteristics. Each of these parameters may affect complement...... activation differently and through different sensing molecules and initiation pathways. The importance of material properties in triggering complement is considered and mechanistic aspects discussed. Mechanistic understanding of complement events could provide rational approaches for improved material design...

  19. Mechanical Properties of Composite Materials

    Directory of Open Access Journals (Sweden)

    Mitsuhiro Okayasu

    2014-10-01

    Full Text Available An examination has been made of the mechanical and failure properties of several composite materials, such as a short and a long carbon fiber reinforced plastic (short- and long-CFRP and metal based composite material. The short CFRP materials were used for a recycled CFRP which fabricated by the following process: the CFRP, consisting of epoxy resin with carbon fiber, is injected to a rectangular plate cavity after mixing with acrylonitrile butadiene styrene resin with different weight fractions of CFRP. The fatigue and ultimate tensile strength (UTS increased with increasing CFRP content. These correlations, however, break down, especially for tensile strength, as the CFPR content becomes more than 70%. Influence of sample temperature on the bending strength of the long-CFRP was investigated, and it appears that the strength slightly decreases with increasing the temperature, due to the weakness in the matrix. Broken fiber and pull-out or debonding between the fiber and matrix were related to the main failure of the short- and long-CFRP samples. Mechanical properties of metal based composite materials have been also investigated, where fiber-like high hardness CuAl2 structure is formed in aluminum matrix. Excellent mechanical properties were obtained in this alloy, e.g., the higher strength and the higher ductility, compared tothe same alloy without the fiber-like structure. There are strong anisotropic effects on the mechanical properties due to the fiber-like metal composite in a soft Al based matrix.

  20. Mitral leaflet modeling: Importance of in vivo shape and material properties.

    Science.gov (United States)

    Stevanella, Marco; Krishnamurthy, Gaurav; Votta, Emiliano; Swanson, Julia C; Redaelli, Alberto; Ingels, Neil B

    2011-08-11

    The anterior mitral leaflet (AML) is a thin membrane that withstands high left ventricular (LV) pressure pulses 100,000 times per day. The presence of contractile cells determines AML in vivo stiffness and complex geometry. Until recently, mitral valve finite element (FE) models have neglected both of these aspects. In this study we assess their effect on AML strains and stresses, hypothesizing that these will differ significantly from those reported in literature. Radiopaque markers were sewn on the LV, the mitral annulus, and AML in sheep hearts, and their four-dimensional coordinates obtained with biplane video fluoroscopy. Employing in vivo data from three representative hearts, AML FE models were created from the marker coordinates at the end of isovolumic relaxation assumed as the unloaded reference state. AML function was simulated backward through systole, applying the measured trans-mitral pressure on AML LV surface and marker displacements on AML boundaries. Simulated AML displacements and curvatures were consistent with in vivo measurements, confirming model accuracy. AML circumferential strains were mostly tensile (1-3%), despite being compressive (-1%) near the commissures. Radial strains were compressive in the belly (-1 to -0.2%), and tensile (2-8%) near the free edge. These results differ significantly from those of previous FE models. They reflect the synergy of high tissue stiffness, which limits tensile circumferential strains, and initial compound curvature, which forces LV pressure to compress AML radially. The obtained AML shape may play a role not only in preventing mitral regurgitation, but also in optimizing LV outflow fluid dynamics.

  1. From Microstructures to Predict Properties of Materials

    Science.gov (United States)

    Wang, Ke-Gang

    2010-03-01

    Understanding the precise and fundamental manner in which materials structures (nanostructures or microstructures) and their evolution influences properties and service lifetimes of advanced materials profoundly impacts material design and today materials design plays an increasingly important rôle in many engineering applications. Linking structures to properties and predicting properties of materials is fundamental step for materials design. First, a framework of applications of multiscale modeling to property prediction of advanced materials will be briefly presented. As an example, a methodology will be shown to link micro-scale to the continuum scale, integrating microstructure modeling with the large Thermo-Calc^ database. This paradigm was successfully applied to the case of Fe-12Ni-6Mn maraging steel. Next, methodology for integrating first-principle calculation into simulations of microstructure evolution will be reviewed. Our methods are sufficiently reliable to permit control and fabrication of quantum-dots structures, nanocrystals, and particle-reinforced nanocomposites, as well as assist in the predictive behavior of macro-scale colloids, aerosols, and other soft matter systems.

  2. Quantify patient-specific coronary material property and its impact on stress/strain calculations using in vivo IVUS data and 3D FSI models: a pilot study.

    Science.gov (United States)

    Guo, Xiaoya; Zhu, Jian; Maehara, Akiko; Monoly, David; Samady, Habib; Wang, Liang; Billiar, Kristen L; Zheng, Jie; Yang, Chun; Mintz, Gary S; Giddens, Don P; Tang, Dalin

    2017-02-01

    Computational models have been used to calculate plaque stress and strain for plaque progression and rupture investigations. An intravascular ultrasound (IVUS)-based modeling approach is proposed to quantify in vivo vessel material properties for more accurate stress/strain calculations. In vivo Cine IVUS and VH-IVUS coronary plaque data were acquired from one patient with informed consent obtained. Cine IVUS data and 3D thin-slice models with axial stretch were used to determine patient-specific vessel material properties. Twenty full 3D fluid-structure interaction models with ex vivo and in vivo material properties and various axial and circumferential shrink combinations were constructed to investigate the material stiffness impact on stress/strain calculations. The approximate circumferential Young's modulus over stretch ratio interval [1.0, 1.1] for an ex vivo human plaque sample and two slices (S6 and S18) from our IVUS data were 1631, 641, and 346 kPa, respectively. Average lumen stress/strain values from models using ex vivo, S6 and S18 materials with 5 % axial shrink and proper circumferential shrink were 72.76, 81.37, 101.84 kPa and 0.0668, 0.1046, and 0.1489, respectively. The average cap strain values from S18 material models were 150-180 % higher than those from the ex vivo material models. The corresponding percentages for the average cap stress values were 50-75 %. Dropping axial and circumferential shrink consideration led to stress and strain over-estimations. In vivo vessel material properties may be considerably softer than those from ex vivo data. Material stiffness variations may cause 50-75 % stress and 150-180 % strain variations.

  3. The extraordinary joint material of an articulated coralline alga. II. Modeling the structural basis of its mechanical properties.

    Science.gov (United States)

    Denny, Mark W; King, Felicia A

    2016-06-15

    By incorporating joints into their otherwise rigid fronds, erect coralline algae have evolved to be as flexible as other seaweeds, which allows them to thrive - and even dominate space - on wave-washed shores around the globe. However, to provide the required flexibility, the joint tissue of Calliarthron cheilosporioides, a representative articulated coralline alga, relies on an extraordinary tissue that is stronger, more extensible and more fatigue resistant than that of other algae. Here, we used the results from recent experiments to parameterize a conceptual model that links the microscale architecture of cell walls to the adaptive mechanical properties of joint tissue. Our analysis suggests that the theory of discontinuous fiber-wound composite materials (with cellulose fibrils as the fibers and galactan gel as the matrix) can explain key aspects of the material's mechanics. In particular, its adaptive viscoelastic behavior can be characterized by two, widely separated time constants. We speculate that the short time constant (∼14 s) results from the viscous response of the matrix to the change in cell-wall shape as a joint is stretched, a response that allows the material both to remain flexible and to dissipate energy as a frond is lashed by waves. We propose that the long time constant (∼35 h), is governed by the shearing of the matrix between cellulose fibrils. The resulting high apparent viscosity ensures that joints avoid accumulating lethal deformation in the course of a frond's lifetime. Our synthesis of experimental measurements allows us to draw a chain of mechanistic inference from molecules to cell walls to fronds and community ecology.

  4. Material Modelling - Composite Approach

    DEFF Research Database (Denmark)

    Nielsen, Lauge Fuglsang

    1997-01-01

    in this report is that cement paste and concrete behave practically as linear-viscoelastic materials from an age of approximately 10 hours. This is a significant age extension relative to earlier studies in the literature where linear-viscoelastic behavior is only demonstrated from ages of a few days. Thus......, linear-viscoelastic analysis methods are justified from the age of approximately 10 hours.The rheological properties of plain cement paste are determined. These properties are the principal material properties needed in any stress analysis of concrete. Shrinkage (autogeneous or drying) of mortar...... and concrete and associated internal stress states are examples of analysis made in this report. In this context is discussed that concrete strength is not an invariable material property. It is a property the potentials of which is highly and negatively influenced by any damage caused by stress concentrations...

  5. Materials modelling in London

    Science.gov (United States)

    Ciudad, David

    2016-04-01

    Angelos Michaelides, Professor in Theoretical Chemistry at University College London (UCL) and co-director of the Thomas Young Centre (TYC), explains to Nature Materials the challenges in materials modelling and the objectives of the TYC.

  6. The combination therapy with alfacalcidol and risedronate improves the mechanical property in lumbar spine by affecting the material properties in an ovariectomized rat model of osteoporosis

    Directory of Open Access Journals (Sweden)

    Ito Masako

    2009-06-01

    Full Text Available Abstract Background We conducted the present study to investigate the therapeutic effects of a combination treatment of alfacalcidol (ALF and risedronate (RIS on the bone mechanical properties of bone and calcium (Ca metabolism using an ovariectomized (OVX rat model of osteoporosis. Methods Female Wistar rats were OVX- or sham-operated at 40 weeks of age. Twelve weeks post-surgery, rats were randomized into seven groups: 1 sham + vehicle, 2 OVX + vehicle, 3 OVX + ALF 0.025 μg/kg/day, 4 OVX + ALF 0.05 μg, 5 OVX + RIS 0.3 mg, 6 OVX + RIS 3.0 mg, 7 OVX + ALF 0.025 μg + RIS 0.3 mg. Each drug was administered orally five times a week for 12 weeks. After treatment, we evaluated the mechanical properties of the lumbar vertebra and femoral midshaft. In the lumbar vertebra, structural and material analyses were performed using micro-computed tomography (micro-CT and microbeam X-ray diffraction (micro-XRD, respectively. Biochemical markers in serum and urine were also determined. Results (1 With respect to improvement in the mechanical strength of the lumbar spine and the femoral midshaft, the combination treatment of ALF and RIS at their sub-therapeutic doses was more effective than each administered as a monotherapy; (2 In the suppression of bone resorption and the amelioration of microstructural parameters, the effects of ALF and RIS were considered to be independent and additive; (3 The improvement of material properties, such as microstructural parameters and the biological apatite (Bap c-axis orientation, contributed to the reinforcement of spinal strength; and (4 The combination treatment of ALF and RIS normalized urinary Ca excretion, suggesting that this treatment ameliorated the changes in Ca metabolism. Conclusion These results demonstrate that the combination treatment of ALF and RIS at their sub-therapeutic doses can improve the mechanical properties of the spine as well as the femur and ameliorate changes in Ca metabolism in an animal

  7. Mechanics of materials model

    Science.gov (United States)

    Meister, Jeffrey P.

    1987-01-01

    The Mechanics of Materials Model (MOMM) is a three-dimensional inelastic structural analysis code for use as an early design stage tool for hot section components. MOMM is a stiffness method finite element code that uses a network of beams to characterize component behavior. The MOMM contains three material models to account for inelastic material behavior. These include the simplified material model, which assumes a bilinear stress-strain response; the state-of-the-art model, which utilizes the classical elastic-plastic-creep strain decomposition; and Walker's viscoplastic model, which accounts for the interaction between creep and plasticity that occurs under cyclic loading conditions.

  8. Mechanical properties of wet granular materials

    Energy Technology Data Exchange (ETDEWEB)

    Fournier, Z; Geromichalos, D; Herminghaus, S; Kohonen, M M; Mugele, F; Scheel, M; Schulz, M; Schulz, B; Schier, Ch; Seemann, R; Skudelny, A

    2005-03-09

    We elaborate on the impact of liquids upon the mechanical properties of granular materials. We find that most of the experimental and simulation results may be accounted for by a simple model assuming frictionless, spherical grains, with a hysteretic attractive interaction between neighbouring grains due to capillary forces.

  9. Tissue level material composition and mechanical properties in Brtl/+ mouse model of Osteogenesis Imperfecta after sclerostin antibody treatment

    Science.gov (United States)

    Lloyd, William R.; Sinder, Benjamin P.; Salemi, Joseph; Ominsky, Michael S.; Marini, Joan C.; Caird, Michelle S.; Morris, Michael D.; Kozloff, Kenneth M.

    2015-02-01

    Osteogenesis imperfecta (OI) is a genetic disorder resulting in defective collagen or collagen-associated proteins and fragile, brittle bones. To date, therapies to improve OI bone mass, such as bisphosphonates, have increased bone mass in the axial skeleton of OI patients, but have shown limited effects at reducing long bone fragility. Sclerostin antibody (Scl- Ab), currently in clinical trials for osteoporosis, stimulates bone formation and may have the potential to reduce long bone fracture rates in OI patients. Scl-Ab has been investigated as an anabolic therapy for OI in the Brtl/+ mouse model of moderately severe Type IV OI. While Scl-Ab increases long bone mass in the Brtl/+ mouse, it is not known whether material properties and composition changes also occur. Here, we report on the effects of Scl-Ab on wild type and Brtl/+ young (3 week) and adult (6 month) male mice. Scl-Ab was administered over 5 weeks (25mg/kg, 2x/week). Raman microspectroscopy and nanoindentation are used for bone composition and biomechanical bone property measurements in excised bone. Fluorescent labels (calcein and alizarin) at 4 time points over the entire treatment period are used to enable measurements at specific tissue age. Differences between wild type and Brtl/+ groups included variations in the mineral and matrix lattices, particularly the phosphate v1, carbonate v1, and the v(CC) proline and hydroxyproline stretch vibrations. Results of Raman spectroscopy corresponded to nanoindentation findings which indicated that old bone (near midcortex) is stiffer (higher elastic modulus) than new bone. We compare and contrast mineral to matrix and carbonate to phosphate ratios in young and adult mice with and without treatment.

  10. Parameter identification of hyperelastic material properties of the heel pad based on an analytical contact mechanics model of a spherical indentation.

    Science.gov (United States)

    Suzuki, Ryo; Ito, Kohta; Lee, Taeyong; Ogihara, Naomichi

    2017-01-01

    Accurate identification of the material properties of the plantar soft tissue is important for computer-aided analysis of foot pathologies and design of therapeutic footwear interventions based on subject-specific models of the foot. However, parameter identification of the hyperelastic material properties of plantar soft tissues usually requires an inverse finite element analysis due to the lack of a practical contact model of the indentation test. In the present study, we derive an analytical contact model of a spherical indentation test in order to directly estimate the material properties of the plantar soft tissue. Force-displacement curves of the heel pads are obtained through an indentation experiment. The experimental data are fit to the analytical stress-strain solution of the spherical indentation in order to obtain the parameters. A spherical indentation approach successfully predicted the non-linear material properties of the heel pad without iterative finite element calculation. The force-displacement curve obtained in the present study was found to be situated lower than those identified in previous studies. The proposed framework for identifying the hyperelastic material parameters may facilitate the development of subject-specific FE modeling of the foot for possible clinical and ergonomic applications.

  11. Modeling multiphase materials processes

    CERN Document Server

    Iguchi, Manabu

    2010-01-01

    ""Modeling Multiphase Materials Processes: Gas-Liquid Systems"" describes the methodology and application of physical and mathematical modeling to multi-phase flow phenomena in materials processing. The book focuses on systems involving gas-liquid interaction, the most prevalent in current metallurgical processes. The performance characteristics of these processes are largely dependent on transport phenomena. This volume covers the inherent characteristics that complicate the modeling of transport phenomena in such systems, including complex multiphase structure, intense turbulence, opacity of

  12. Probabilistic Approach for Determining the Material Properties of Meniscal Attachments In Vivo Using Magnetic Resonance Imaging and a Finite Element Model.

    Science.gov (United States)

    Kang, Kyoung-Tak; Kim, Sung-Hwan; Son, Juhyun; Lee, Young Han; Chun, Heoung-Jae

    2015-12-01

    The material properties of in vivo meniscal attachments were evaluated using a probabilistic finite element (FE) model and magnetic resonance imaging (MRI). MRI scans of five subjects were collected at full extension and 30°, 60°, and 90° flexion. One subject with radiographic evidence of no knee injury and four subjects with Kellgren-Lawrence score of 1 or 2 (two each) were recruited. Isovoxel sagittal three-dimensional cube sequences of the knee were acquired in extension and flexion. Menisci movement in flexion was investigated using sensitivity analysis based on the Monte Carlo method in order to generate a subject-specific FE model to evaluate significant factors. The material properties of horn attachment in the five-subject FE model were optimized to minimize the differences between meniscal movements in the FE model and MR images in flexion. We found no significant difference between normal and patient knees in flexion with regard to movement of anterior, posterior, medial, and lateral menisci or changes in height morphology. At 90° flexion, menisci movement was primarily influenced by posterior horn stiffness, followed by anterior horn stiffness, the transverse ligament, and posterior cruciate ligament. The optimized material properties model predictions for menisci motion were more accurate than the initial material properties model. The results of this approach suggest that the material properties of horn attachment, which affects the mobile characteristics of menisci, could be determined in vivo. Thus, this study establishes a basis for a future design method of attachment for tissue-engineered replacement menisci.

  13. Modeling the mechanical and aging properties of silicone rubber and foam - stockpile-historical & additively manufactured materials

    Energy Technology Data Exchange (ETDEWEB)

    Maiti, A; Weisgraber, T H; Gee, R H

    2014-09-30

    M97* and M9763 belong to the M97xx series of cellular silicone materials that have been deployed as stress cushions in some of the LLNL systems. Their purpose of these support foams is to distribute the stress between adjacent components, maintain relative positioning of various components, and mitigate the effects of component size variation due to manufacturing and temperature changes. In service these materials are subjected to a continuous compressive strain over long periods of time. In order to ensure their effectiveness, it is important to understand how their mechanical properties change over time. The properties we are primarily concerned about are: compression set, load retention, and stress-strain response (modulus).

  14. Properties of Three Pseudo-Spins in Ferroelectric or Ferro-Antiferroelectric Materials Described by a Transverse Ising Model

    Institute of Scientific and Technical Information of China (English)

    JIANG Wei; Veng-Cheong Lo

    2005-01-01

    Ferroelectric phase diagrams and the temperature dependence of polarization, dielectric properties of the three pseudo-spin in ferroelectric or ferro-antiferroelectric system described by a transverse Ising models are investigated on the basis of the effective-field theory with the differential operator technique. The effects of the transverse field and the coupling strength between the nearest-neighboring pseudo-spin on the physical properties are discussed in detail.

  15. Bilayered graphene/h-BN with folded holes as new nanoelectronic materials: modeling of structures and electronic properties

    Science.gov (United States)

    Chernozatonskii, Leonid A.; Demin сtor A., Vi; Bellucci, Stefano

    2016-11-01

    The latest achievements in 2-dimensional (2D) material research have shown the perspective use of sandwich structures in nanodevices. We demonstrate the following generation of bilayer materials for electronics and optoelectronics. The atomic structures, the stability and electronic properties of Moiré graphene (G)/h-BN bilayers with folded nanoholes have been investigated theoretically by ab-initio DFT method. These perforated bilayers with folded hole edges may present electronic properties different from the properties of both graphene and monolayer nanomesh structures. The closing of the edges is realized by C-B(N) bonds that form after folding the borders of the holes. Stable ≪round≫ and ≪triangle≫ holes organization are studied and compared with similar hole forms in single layer graphene. The electronic band structures of the considered G/BN nanomeshes reveal semiconducting or metallic characteristics depending on the sizes and edge terminations of the created holes. This investigation of the new types of G/BN nanostructures with folded edges might provide a directional guide for the future of this emerging area.

  16. On Structure and Properties of Amorphous Materials

    Directory of Open Access Journals (Sweden)

    Zbigniew H. Stachurski

    2011-09-01

    Full Text Available Mechanical, optical, magnetic and electronic properties of amorphous materials hold great promise towards current and emergent technologies. We distinguish at least four categories of amorphous (glassy materials: (i metallic; (ii thin films; (iii organic and inorganic thermoplastics; and (iv amorphous permanent networks. Some fundamental questions about the atomic arrangements remain unresolved. This paper focuses on the models of atomic arrangements in amorphous materials. The earliest ideas of Bernal on the structure of liquids were followed by experiments and computer models for the packing of spheres. Modern approach is to carry out computer simulations with prediction that can be tested by experiments. A geometrical concept of an ideal amorphous solid is presented as a novel contribution to the understanding of atomic arrangements in amorphous solids.

  17. Effect of material properties on predicted vesical pressure during a cough in a simplified computational model of the bladder and urethra.

    Science.gov (United States)

    Spirka, Thomas; Kenton, Kimberly; Brubaker, Linda; Damaser, Margot S

    2013-01-01

    Stress urinary incontinence is a condition that affects mainly women and is characterized by the involuntary loss of urine in conjunction with an increase in abdominal pressure but in the absence of a bladder contraction. In spite of the large number of women affected by this condition, little is known regarding the mechanics associated with the maintenance of continence in women. Urodynamic measurements of the pressure acting on the bladder and the pressures developed within the bladder and the urethra offer a potential starting point for constructing computational models of the bladder and urethra during stress events. The measured pressures can be utilized in these models to provide information to specify loads and validate the models. The main goals of this study were to investigate the feasibility of incorporating human urodynamic pressure data into a computational model of the bladder and the urethra during a cough and determine if the resulting model could be validated through comparison of predicted and measured vesical pressure. The results of this study indicated that simplified models can predict vesical pressures that differ by less than 5 cmH(2)O (pressure measurements. In addition, varying material properties had a minimal impact on the vesical pressure and displacements predicted by the model. The latter finding limits the use of vesical pressure as a validation criterion since different parameters can yield similar results in the same model. However, the insensitivity of vesical pressure predictions to material properties ensures that the outcome of our models is not highly sensitive to tissue material properties, which are not well characterized.

  18. 2nd International Workshop on Physics-Based Modelling of Material Properties and Experimental Observations with special focus on Fracture and Damage Mechanics: Book of Abstracts

    OpenAIRE

    Nilsson, Karl-Fredrik; YALCINKAYA Tuncay; Oren, Ersin Emre; Tekoğlu, Cihan

    2013-01-01

    This report covers the book of abstracts of the 2nd International Workshop on Physics Based Modelling of Material Properties and Experimental Observations, with special focus on Fracture and Damage Mechanics. The workshop is organized in the context of European Commission’s Enlargement and Integration Action, by the Joint Research Centre in collaboration with the TOBB University of Economics and Technology (TOBB ETU) on 15th-17th May 2013 in Antalya, Turkey. The abstracts of the keynote le...

  19. Modeling the Peano fluidic muscle and the effects of its material properties on its static and dynamic behavior

    Science.gov (United States)

    Veale, Allan Joshua; Xie, Sheng Quan; Anderson, Iain Alexander

    2016-06-01

    The promise of wearable assistive robotics cannot be realized without the development of actuators that mimic the behavior and form of biological muscles. Planar fluidic muscles known as Peano muscles or pouch motors have the potential to provide the high force and compliance of McKibben pneumatic artificial muscles with the low threshold pressure of pleated pneumatic artificial muscles. Yet they do so in a soft and slim form that can be discreetly distributed over the human body. This work is an investigation into the empirical modeling of the Peano muscle, the effect of its material on its performance, and its capabilities and limitations. We discovered that the Peano muscle could provide responsive and discreet actuation of soft and rigid bodies requiring strains between 15% and 30%. Ideally, they are made of non-viscoelastic materials with high tensile and low bending stiffnesses. While Sarosi et al’s empirical model accurately captures its static behavior with an root mean square error of 10.2 N, their dynamic model overestimates oscillation frequency and damping. We propose that the Peano muscle be modeled by a parallel ideal contractile unit and viscoelastic element, both in series with another viscoelastic element.

  20. MIDAS (Material Implementation, Database, and Analysis Source): A comprehensive resource of material properties

    Energy Technology Data Exchange (ETDEWEB)

    Tang, M; Norquist, P; Barton, N; Durrenberger, K; Florando, J; Attia, A

    2010-12-13

    MIDAS is aimed to be an easy-to-use and comprehensive common source for material properties including both experimental data and models and their parameters. At LLNL, we will develop MIDAS to be the central repository for material strength related data and models with the long-term goal to encompass other material properties. MIDAS will allow the users to upload experimental data and updated models, to view and read materials data and references, to manipulate models and their parameters, and to serve as the central location for the application codes to access the continuously growing model source codes. MIDAS contains a suite of interoperable tools and utilizes components already existing at LLNL: MSD (material strength database), MatProp (database of materials properties files), and MSlib (library of material model source codes). MIDAS requires significant development of the computer science framework for the interfaces between different components. We present the current status of MIDAS and its future development in this paper.

  1. Fundamentals of semiconductors physics and materials properties

    CERN Document Server

    Yu, Peter Y

    2005-01-01

    Provides detailed explanations of the electronic, vibrational, transport, and optical properties of semiconductors. This textbook emphasizes understanding the physical properties of Si and similar tetrahedrally coordinated semiconductors and features an extensive collection of tables of material parameters, figures, and problems.

  2. Finite element and micromechanical modeling for investigating effective material properties of polymer-matrix nanocomposites with microfiber, reinforced by CNT arrays

    Science.gov (United States)

    Tahouneh, Vahid; Mashhadi, Mahmoud Mosavi; Naei, Mohammad Hasan

    2016-09-01

    This paper is motivated by the lack of studies to investigate the effect of fiber reinforced CNT arrays on the material properties of nanocomposites. To make a comprehensive study, this research work is conducted in two ways. Firstly, the effect of microfiber as reinforcement on the effective material properties is investigated; secondly, the study is carried on as the microfibers reinforced by CNT arrays. In both above-mentioned approaches, the results are compared to the results of generalized mixture rule which is known as a widely used micro-mechanical model. The representative volume element (RVE) is considered as a well-known method to investigate the effect of adding CNT arrays on the skin of microfibers. The results show that Generalized Mixture Rule cannot properly predict the effects of changing the length and diameter of nanotubes on the effective properties of nanocomposites. The main objective of this research work is to determine the effects of increasing nanotubes on the elastic properties which are achieved using two aforementioned methods including FE and rule of mixture. It is also absorbed; effective properties of RVE can be improved by increasing the volume fraction, length and decreasing CNT arrays diameter.

  3. Optimization of Structure and Material Properties for Solids Composed of Softening Material

    DEFF Research Database (Denmark)

    Bendsøe, Martin P.; Guedes, J.M.; J.M., Plaxton;

    1996-01-01

    Recent results on the design of material properties in the context of global structural optimization provide, in analytical form, a prediction of the optimal material tensor distributions for two or three dimensional continuum structures. The model developed for that purpose is extended here...... to cover the design of a structure and associated material properties for a system composed of a generic form of nonlinear softening material. As was established in the earlier study on design with linear materials, the formulation for combined 'material and structure' design with softening materials can...

  4. Spin-crossover materials properties and applications

    CERN Document Server

    Halcrow, Malcolm A

    2013-01-01

    The phenomenon of spin-crossover has a large impact on the physical properties of a solid material, including its colour, magnetic moment, and electrical resistance. Some materials also show a structural phase change during the transition. Several practical applications of spin-crossover materials have been demonstrated including display and memory devices, electrical and electroluminescent devices, and MRI contrast agents. Switchable liquid crystals, nanoparticles, and thin films of spin-crossover materials have also been achieved. Spin-Crossover Materials: Properties and Applicat

  5. Tailoring of epoxy material properties

    NARCIS (Netherlands)

    Nakka, J.S.

    2010-01-01

    This research work is aimed to understand the effect of resin chemistry on the physical properties (e.g. moduli, viscoelasticity, moisture uptake, coefficient of thermal expansion) of cured aromatic epoxy-amine thermoset resins. This understanding will result into a good first approximation of the f

  6. Fundamental properties of semiconductor materials, and material performance in detectors

    Science.gov (United States)

    Casper, K. J.

    1973-01-01

    Procedures for determining fundamental properties of semiconductor materials, their performance as radiation detectors, and their service life as such detectors are given. Relationships were established between the minority carrier lifetime in the bulk of the material and the charge collection efficiency of the detector.

  7. Properties and characterization of modern materials

    CERN Document Server

    Altenbach, Holm

    2017-01-01

    This book focuses on robust characterization and prediction methods for materials in technical applications as well as the materials’ safety features during operation. In particular, it presents methods for reliably predicting material properties, an aspect that is becoming increasingly important as engineering materials are pushed closer and closer to their limits to boost the performance of machines and structures. To increase their engineering value, components are now designed under the consideration of their multiphysical properties and functions, which requires much more intensive investigation and characterization of these materials. The materials covered in this monograph range from metal-based groups such as lightweight alloys, to advanced high-strength steels and modern titanium alloys. Furthermore, a wide range of polymers and composite materials (e.g. with micro- and nanoparticles or fibres) is covered. The book explores methods for property prediction from classical mechanical characterization-...

  8. Design of materials with prescribed nonlinear properties

    DEFF Research Database (Denmark)

    Wang, Fengwen; Sigmund, Ole; Jensen, Jakob Søndergaard

    2014-01-01

    We systematically design materials using topology optimization to achieve prescribed nonlinear properties under finite deformation. Instead of a formal homogenization procedure, a numerical experiment is proposed to evaluate the material performance in longitudinal and transverse tensile tests un....... The numerical examples illustrate optimized materials with rubber-like behavior and also optimized materials with extreme strain-independent Poisson's ratio for axial strain intervals of εi ∈ [0.00,0.30]. © 2014 Elsevier Ltd. All rights reserved....... under finite deformation, i.e. stress-strain relations and Poisson's ratio. By minimizing errors between actual and prescribed properties, materials are tailored to achieve the target. Both two dimensional (2D) truss-based and continuum materials are designed with various prescribed nonlinear properties...

  9. Learning targeted materials properties from data

    Science.gov (United States)

    Lookman, Turab; Balachandran, Prasanna V.; Dezhen, Xue; Theiler, James; Hogden, John

    We compare several strategies using a data set of 223 M2AX family of compounds for which the elastic properties [bulk (B), shear (G), and Young's (E) modulus] have been computed using density functional theory. The strategy is decomposed into two steps: a regressor is trained to predict elastic properties in terms of elementary orbital radii of the individual components of the materials; and a selector uses these predictions to choose the next material to investigate. The ultimate goal is to obtain a material with desired elastic properties. We examine how the choice of data set size, regressor and selector impact the results.

  10. Dynamic properties of ceramic materials

    Energy Technology Data Exchange (ETDEWEB)

    Grady, D.E. [Sandia National Labs., Albuquerque, NM (United States). Experimental Impact Physics Dept.

    1995-02-01

    The present study offers new data and analysis on the transient shock strength and equation-of-state properties of ceramics. Various dynamic data on nine high strength ceramics are provided with wave profile measurements, through velocity interferometry techniques, the principal observable. Compressive failure in the shock wave front, with emphasis on brittle versus ductile mechanisms of deformation, is examined in some detail. Extensive spall strength data are provided and related to the theoretical spall strength, and to energy-based theories of the spall process. Failure waves, as a mechanism of deformation in the transient shock process, are examined. Strength and equation-of-state analysis of shock data on silicon carbide, boron carbide, tungsten carbide, silicon dioxide and aluminum nitride is presented with particular emphasis on phase transition properties for the latter two. Wave profile measurements on selected ceramics are investigated for evidence of rate sensitive elastic precursor decay in the shock front failure process.

  11. Fundamental-Solution-Based Hybrid Element Model for Nonlinear Heat Conduction Problems with Temperature-Dependent Material Properties

    Directory of Open Access Journals (Sweden)

    Hui Wang

    2013-01-01

    Full Text Available The boundary-type hybrid finite element formulation coupling the Kirchhoff transformation is proposed for the two-dimensional nonlinear heat conduction problems in solids with or without circular holes, and the thermal conductivity of material is assumed to be in terms of temperature change. The Kirchhoff transformation is firstly used to convert the nonlinear partial differential governing equation into a linear one by introducing the Kirchhoff variable, and then the new linear system is solved by the present hybrid finite element model, in which the proper fundamental solutions associated with some field points are used to approximate the element interior fields and the conventional shape functions are employed to approximate the element frame fields. The weak integral functional is developed to link these two fields and establish the stiffness equation with sparse and symmetric coefficient matrix. Finally, the algorithm is verified on several examples involving various expressions of thermal conductivity and existence of circular hole, and numerical results show good accuracy and stability.

  12. Closed-form formulas for the effective properties of random particulate nanocomposites with complete Gurtin-Murdoch model of material surfaces

    Science.gov (United States)

    Nazarenko, Lidiia; Bargmann, Swantje; Stolarski, Henryk

    2017-01-01

    The objective of this work is to present an approach allowing for inclusion of the complete Gurtin-Murdoch material surface equations in methods leading to closed-form formulas defining effective properties of particle-reinforced nanocomposites. Considering that all previous developments of the closed-form formulas for effective properties employ only some parts of the Gurtin-Murdoch model, its complete inclusion constitutes the main focus of this work. To this end, the recently introduced new notion of the energy-equivalent inhomogeneity is generalized to precisely include all terms of the model. The crucial aspect of that generalization is the identification of the energy associated with the last term of the Gurtin-Murdoch equation, i.e., with the surface gradient of displacements. With the help of that definition, the real nanoparticle and its surface possessing its own distinct elastic properties and residual stresses are replaced by an energy-equivalent inhomogeneity with properties incorporating all surface effects. Such equivalent inhomogeneity can then be used in combination with any existing homogenization method. In this work, the method of conditional moments is used to analyze composites with randomly dispersed spherical nanoparticles. Closed-form expressions for effective moduli are derived for both bulk and shear moduli. As numerical examples, nanoporous aluminum is investigated. The normalized bulk and shear moduli of nanoporous aluminum as a function of residual stresses are analyzed and evaluated in the context of other theoretical predictions.

  13. Closed-form formulas for the effective properties of random particulate nanocomposites with complete Gurtin-Murdoch model of material surfaces

    Science.gov (United States)

    Nazarenko, Lidiia; Bargmann, Swantje; Stolarski, Henryk

    2016-07-01

    The objective of this work is to present an approach allowing for inclusion of the complete Gurtin-Murdoch material surface equations in methods leading to closed-form formulas defining effective properties of particle-reinforced nanocomposites. Considering that all previous developments of the closed-form formulas for effective properties employ only some parts of the Gurtin-Murdoch model, its complete inclusion constitutes the main focus of this work. To this end, the recently introduced new notion of the energy-equivalent inhomogeneity is generalized to precisely include all terms of the model. The crucial aspect of that generalization is the identification of the energy associated with the last term of the Gurtin-Murdoch equation, i.e., with the surface gradient of displacements. With the help of that definition, the real nanoparticle and its surface possessing its own distinct elastic properties and residual stresses are replaced by an energy-equivalent inhomogeneity with properties incorporating all surface effects. Such equivalent inhomogeneity can then be used in combination with any existing homogenization method. In this work, the method of conditional moments is used to analyze composites with randomly dispersed spherical nanoparticles. Closed-form expressions for effective moduli are derived for both bulk and shear moduli. As numerical examples, nanoporous aluminum is investigated. The normalized bulk and shear moduli of nanoporous aluminum as a function of residual stresses are analyzed and evaluated in the context of other theoretical predictions.

  14. Calibrated Properties Model

    Energy Technology Data Exchange (ETDEWEB)

    C. Ahlers; H. Liu

    2000-03-12

    The purpose of this Analysis/Model Report (AMR) is to document the Calibrated Properties Model that provides calibrated parameter sets for unsaturated zone (UZ) flow and transport process models for the Yucca Mountain Site Characterization Project (YMP). This work was performed in accordance with the ''AMR Development Plan for U0035 Calibrated Properties Model REV00. These calibrated property sets include matrix and fracture parameters for the UZ Flow and Transport Model (UZ Model), drift seepage models, drift-scale and mountain-scale coupled-processes models, and Total System Performance Assessment (TSPA) models as well as Performance Assessment (PA) and other participating national laboratories and government agencies. These process models provide the necessary framework to test conceptual hypotheses of flow and transport at different scales and predict flow and transport behavior under a variety of climatic and thermal-loading conditions.

  15. "a" interfacial parameter in Nicolais-Narkis model for yield strength of polymer particulate nanocomposites as a function of material and interphase properties.

    Science.gov (United States)

    Zare, Yasser

    2016-05-15

    In this paper, "a" interfacial parameter in Nicolais-Narkis model is expressed by thickness "ri" and strength "σi" of interphase between polymer and nanoparticles as well as material properties. "a" parameter is connected to "B1" interfacial parameter in modified Pukanszky model and the effects of "ri" and "σi" on "a" are explained. The negligible difference between "a" values calculated by fitting the experimental results to Nicolais-Narkis model and also, by "B1" results confirms the accurateness of the suggested relation between "a" and "B1" parameters. Additionally, an inverse relation is found between "a" and "B1" parameters for nanocomposites containing spherical nanoparticles. The results demonstrate that the slight levels of "ri" and "σi" data give a large value of "a" which indicates the poor interfacial adhesion.

  16. Magnetic materials fundamentals, products, properties, applications

    CERN Document Server

    Hilzinger, Rainer

    2013-01-01

    At a practical level, this compendium reviews the basics of soft and hard magnetic materials, discusses the advantages of the different processing routes for the exploitation of the magnetic properties and hence assists in proper, fail-safe and economic application of magnetic materials. Essential guidelines and formulas for the calculation of the magnetic and electrical properties, temperature and long-term stability of permanent magnets, of inductive components and magnetic shielding are compiled. Selected fields of application and case studies illustrate the large diversity of technical applications. Application engineers will appreciate the comprehensive compilation of the properties and detailed characteristic curves of modern soft and hard magnetic materials. Materials scientists will enjoy the presentation of the different processing routes and their impact on the magnetic properties and students will profit from the survey from the basics of magnetism down to the applications in inductive components, ...

  17. Numerical modeling of advanced materials

    NARCIS (Netherlands)

    Meinders, T.; Perdahcioglu, E.S.; Riel, van M.; Wisselink, H.H.

    2007-01-01

    The finite element (FE) method is widely used to numerically simulate forming processes. The accuracy of an FE analysis strongly depends on the extent to which a material model can represent the real material behavior. The use of new materials requires complex material models which are able to descr

  18. Size-Dependent Materials Properties Toward a Universal Equation

    Directory of Open Access Journals (Sweden)

    Guisbiers G

    2010-01-01

    Full Text Available Abstract Due to the lack of experimental values concerning some material properties at the nanoscale, it is interesting to evaluate this theoretically. Through a “top–down” approach, a universal equation is developed here which is particularly helpful when experiments are difficult to lead on a specific material property. It only requires the knowledge of the surface area to volume ratio of the nanomaterial, its size as well as the statistic (Fermi–Dirac or Bose–Einstein followed by the particles involved in the considered material property. Comparison between different existing theoretical models and the proposed equation is done.

  19. Measurement of thermal properties of PCM materials

    Energy Technology Data Exchange (ETDEWEB)

    Domanski, R.; Jaworski, M. [Warsaw Univ. of Technology (Poland). Inst. of Heat Engineering

    1994-12-31

    In the article results of measurements of thermal properties of PCM (phase change materials) and their stability are presented. These include specific heat, temperature of phase change, latent heat and enthalpy as a function of temperature. Different kind of materials were considered, especially some waxes, n-alkanes and salt hydrates. Measurements of thermal capacity of materials were performed using two techniques - standard DSC (for small samples and pure materials) and simple thermal analysis based on the measurement of temperature field in relatively big samples (about 20-50 g). Stability of thermal properties in many cycles of melting and solidification for some materials obtained in special set-up (for fast cycling) are presented. On the base of measurements mathematical formulas describing enthalpy vs. temperature for some materials were developed. These are very useful in computer simulation of thermal storage systems with PCM. (orig.)

  20. Geometric and mechanical properties evaluation of scaffolds for bone tissue applications designing by a reaction-diffusion models and manufactured with a material jetting system

    Directory of Open Access Journals (Sweden)

    Marco A. Velasco

    2016-10-01

    Full Text Available Scaffolds are essential in bone tissue engineering, as they provide support to cells and growth factors necessary to regenerate tissue. In addition, they meet the mechanical function of the bone while it regenerates. Currently, the multiple methods for designing and manufacturing scaffolds are based on regular structures from a unit cell that repeats in a given domain. However, these methods do not resemble the actual structure of the trabecular bone which may work against osseous tissue regeneration. To explore the design of porous structures with similar mechanical properties to native bone, a geometric generation scheme from a reaction-diffusion model and its manufacturing via a material jetting system is proposed. This article presents the methodology used, the geometric characteristics and the modulus of elasticity of the scaffolds designed and manufactured. The method proposed shows its potential to generate structures that allow to control the basic scaffold properties for bone tissue engineering such as the width of the channels and porosity. The mechanical properties of our scaffolds are similar to trabecular tissue present in vertebrae and tibia bones. Tests on the manufactured scaffolds show that it is necessary to consider the orientation of the object relative to the printing system because the channel geometry, mechanical properties and roughness are heavily influenced by the position of the surface analyzed with respect to the printing axis. A possible line for future work may be the establishment of a set of guidelines to consider the effects of manufacturing processes in designing stages.

  1. Finite Element Method for Analysis of Material Properties

    DEFF Research Database (Denmark)

    Rauhe, Jens Christian

    description of the material microstructure the finite element models must contain a large number of elements and this problem is solved by using the preconditioned conjugated gradient solver with an Element-By-Element preconditioner. Finite element analysis provides the volume averaged stresses and strains...... and the finite element method. The material microstructure of the heterogeneous material is non-destructively determined using X-ray microtomography. A software program has been generated which uses the X-ray tomographic data as an input for the mesh generation of the material microstructure. To obtain a proper...... which are used for the determination of the effective properties of the heterogeneous material. Generally, the properties determined using the finite element method coupled with X-ray microtomography are in good agreement with both experimentally determined properties and properties determined using...

  2. Stochastic multiscale modeling of polycrystalline materials

    Science.gov (United States)

    Wen, Bin

    Mechanical properties of engineering materials are sensitive to the underlying random microstructure. Quantification of mechanical property variability induced by microstructure variation is essential for the prediction of extreme properties and microstructure-sensitive design of materials. Recent advances in high throughput characterization of polycrystalline microstructures have resulted in huge data sets of microstructural descriptors and image snapshots. To utilize these large scale experimental data for computing the resulting variability of macroscopic properties, appropriate mathematical representation of microstructures is needed. By exploring the space containing all admissible microstructures that are statistically similar to the available data, one can estimate the distribution/envelope of possible properties by employing efficient stochastic simulation methodologies along with robust physics-based deterministic simulators. The focus of this thesis is on the construction of low-dimensional representations of random microstructures and the development of efficient physics-based simulators for polycrystalline materials. By adopting appropriate stochastic methods, such as Monte Carlo and Adaptive Sparse Grid Collocation methods, the variability of microstructure-sensitive properties of polycrystalline materials is investigated. The primary outcomes of this thesis include: (1) Development of data-driven reduced-order representations of microstructure variations to construct the admissible space of random polycrystalline microstructures. (2) Development of accurate and efficient physics-based simulators for the estimation of material properties based on mesoscale microstructures. (3) Investigating property variability of polycrystalline materials using efficient stochastic simulation methods in combination with the above two developments. The uncertainty quantification framework developed in this work integrates information science and materials science, and

  3. Optical properties of low-dimensional materials

    CERN Document Server

    Ogawa, T

    1998-01-01

    This book surveys recent theoretical and experimental studies of optical properties of low-dimensional materials. As an extended version of Optical Properties of Low-Dimensional Materials (Volume 1, published in 1995 by World Scientific), Volume 2 covers a wide range of interesting low-dimensional materials including both inorganic and organic systems, such as disordered polymers, deformable molecular crystals, dilute magnetic semiconductors, SiGe/Si short-period superlattices, GaAs quantum wires, semiconductor microcavities, and photonic crystals. There are excellent review articles by promis

  4. Design and properties of maxillofacial prosthetic materials.

    Science.gov (United States)

    Andreopoulos, A G; Theophanides, T

    1993-11-01

    Maxillofacial reconstruction by prosthetic means is a valuable contribution that medicine offers to the public. Materials design and properties are the main problems faced by scientists in this field. Materials used for intraoral prostheses are not ideal, but they have been perfected to the point of practical use. Denture resins, gold, chromium-cobalt alloys, and porcelain are widely used and produce acceptable results in the oral cavity. In this review, the properties and performance of some polymeric materials used in maxillofacial prosthetics are discussed, and new trends in research and development are also reported.

  5. Bioactive glasses materials, properties and applications

    CERN Document Server

    Ylänen, Heimo

    2011-01-01

    Due to their biocompatibility and bioactivity, bioactive glasses are used as highly effective implant materials throughout the human body to replace or repair damaged tissue. As a result, they have been in continuous use since shortly after their invention in the late 1960s and are the subject of extensive research worldwide.Bioactive glasses provides readers with a detailed review of the current status of this unique material, its properties, technologies and applications. Chapters in part one deal with the materials and mechanical properties of bioactive glass, examining topics such

  6. Thermal protection materials: Thermophysical property data

    Science.gov (United States)

    Williams, S. D.; Curry, Donald M.

    1992-01-01

    This publication presents a thermophysical property survey on materials that could potentially be used for future spacecraft thermal protection systems (TPS). This includes data that was reported in the 1960's as well as more current information reported through the 1980's. An attempt was made to cite the manufacturers as well as the data source in the bibliography. This volume represents an attempt to provide in a single source a complete set of thermophysical data on a large variety of materials used in spacecraft TPS analysis. The property data is divided into two categories: ablative and reusable. The ablative materials have been compiled into twelve categories that are descriptive of the material composition. An attempt was made to define the Arrhenius equation for each material although this data may not be available for some materials. In a similar manner, char data may not be available for some of the ablative materials. The reusable materials have been divided into three basic categories: thermal protection materials (such as insulators), adhesives, and structural materials.

  7. Multifunctional Polycrystalline Ferroelectric Materials Processing and Properties

    CERN Document Server

    Pardo, Lorena

    2011-01-01

    This book presents selected topics on processing and properties of ferroelectric materials that are currently the focus of attention in scientific and technical research. Ferro-piezoelectric ceramics are key materials in devices for many applications, such as automotive, healthcare and non-destructive testing. As they are polycrystalline, non-centrosymmetric materials, their piezoelectricity is induced by the so-called poling process. This is based on the principle of polarization reversal by the action of an electric field that characterizes the ferroelectric materials. This book was born with the aim of increasing the awareness of the multifunctionality of ferroelectric materials among different communities, such as researchers, electronic engineers, end-users and manufacturers, working on and with ferro-piezoelectric ceramic materials and devices which are based on them. The initiative to write this book comes from a well-established group of researchers at the Laboratories of Ferroelectric Materials, Mate...

  8. Microstructure and Property Evolution in Advanced Cladding and Duct Materials Under Long-Term and Elevated Temperature Irradiation: Modeling and Experimental Investigation

    Energy Technology Data Exchange (ETDEWEB)

    Wirth, Brian; Morgan, Dane; Kaoumi, Djamel; Motta, Arthur

    2013-12-01

    The in-service degradation of reactor core materials is related to underlying changes in the irradiated microstructure. During reactor operation, structural components and cladding experience displacement of atoms by collisions with neutrons at temperatures at which the radiation-induced defects are mobile, leading to microstructure evolution under irradiation that can degrade material properties. At the doses and temperatures relevant to fast reactor operation, the microstructure evolves by dislocation loop formation and growth, microchemistry changes due to radiation-induced segregation, radiation-induced precipitation, destabilization of the existing precipitate structure, and in some cases, void formation and growth. These processes do not occur independently; rather, their evolution is highly interlinked. Radiationinduced segregation of Cr and existing chromium carbide coverage in irradiated alloy T91 track each other closely. The radiation-induced precipitation of Ni-Si precipitates and RIS of Ni and Si in alloys T91 and HCM12A are likely related. Neither the evolution of these processes nor their coupling is understood under the conditions required for materials performance in fast reactors (temperature range 300-600°C and doses beyond 200 dpa). Further, predictive modeling is not yet possible as models for microstructure evolution must be developed along with experiments to characterize these key processes and provide tools for extrapolation. To extend the range of operation of nuclear fuel cladding and structural materials in advanced nuclear energy and transmutation systems to that required for the fast reactor, the irradiation-induced evolution of the microstructure, microchemistry, and the associated mechanical properties at relevant temperatures and doses must be understood. Predictive modeling relies on an understanding of the physical processes and also on the development of microstructure and microchemical models to describe their evolution under

  9. Modelling Real Property Transactions

    DEFF Research Database (Denmark)

    Stubkjær, Erik

    2002-01-01

    . The developed models and a subsequent comparative analysis can be used for improving the efficiency of the procedures. Further-more, the COST action will support Ph.D.-studies by providing a much-needed international research framework and a basis for Ph.D.-level courses. The paper develops on the multi...... of researchers relate to surveying studies, and hence to the FIG. The main objective of the action is to improve the transparency of real property markets and to provide a stronger basis for the reduction of costs of real property transactions by preparing a set of models of real property transaction...

  10. Bone strength and material properties of the glenoid

    DEFF Research Database (Denmark)

    Frich, Lars Henrik; Jensen, N.C.; Odgaard, A.;

    1997-01-01

    The quality of the glenoid bone is important to a successful total shoulder replacement. Finite element models have been used to model the response of the glenoid bone to an implanted prosthesis. Because very little is known about the bone strength and the material properties at the glenoid, thes...

  11. Prediction of the vertebral strength using a finite element model derived from low-dose biplanar imaging: benefits of subject-specific material properties.

    Science.gov (United States)

    Sapin-de Brosses, Emilie; Jolivet, Erwan; Travert, Christophe; Mitton, David; Skalli, Wafa

    2012-02-01

    A finite element analysis on osteoporotic vertebrae. This study aims to validate subject-specific finite element models (FEMs) derived from a low-dose imaging system (EOS, Biospace Med, France) for the prediction of vertebral strength. The vertebrae are submitted to an eccentric compression force leading to compression and anterior bending. Given the aging population, osteoporosis and vertebral fractures are a major public health issue. A low bone mineral density (BMD) does not always explain incident fractures, and multifactorial analyses are required. In this context, FEMs based on quantitative computed tomography (QCT) have been proposed to predict vertebral strength in vitro or quantify effects of treatments. However, the clinical use of such a model for the in vivo follow-up of the whole spine is limited by the high-radiation dose induced by QCT and the lying position, which does not allow postural assessment with the same modality. Fourteen vertebrae were modeled using a parametric meshing method. The mesh was subject-specific using geometric parameters computed on the 3-dimensional (3D) reconstructions obtained from the EOS biplanar radiographs. The contribution of cortical bone was taken into account by modeling a cortico-cancellous shell whose properties were derived from experimental data. The effect of subject-specific bone Young's moduli derived from EOS vertebral areal BMD was quantified. The 3D position of the point-of-load application and the 3D orientation of the force was faithfully reproduced in the model to compare the predicted strength and experimental strength under the same loading conditions. The relative error of prediction decreased from 43% to 16% (2.5 times) when subject-specific mechanical properties, derived from EOS areal BMD, were implemented in the FEM compared with averaged material properties. The resulting subject-specific FEMs predicted vertebral strength with a level of significance close to the QCT-based models (r adjusted = 0

  12. Multiscale Modeling and Computation of Liquid Crystal Polymers, Polymer Blends, and Polymer Nanocomposites: Investigation of Rheology and Material Properties

    Science.gov (United States)

    2008-04-15

    Multiscale kinetic theories for flows of biaxial liquid crystal polymers Given the rising interests in the modeling of nanofluids of biaxial constituents...Newtonian Fluid Mechanics, 2006, 128(1): 44-61. 4. M. G. Forest, R. Zhou, and Q. Wang, Nano-rod suspension flows: a 2D Smoluchowski-Navier-Stokes...dynamics for rigid rod & platelet suspensions in strongly coupled coplanar linear flow and magnetic fields II: Kinetic theory, Physics of Fluids, 2006, 18

  13. Finite Element Method for Analysis of Material Properties

    DEFF Research Database (Denmark)

    Rauhe, Jens Christian

    The use of cellular and composite materials have in recent years become more and more common in all kinds of structural components and accurate knowledge of the effective properties is therefore essential. In this wok the effective properties are determined using the real material microstructure...... and the finite element method. The material microstructure of the heterogeneous material is non-destructively determined using X-ray microtomography. A software program has been generated which uses the X-ray tomographic data as an input for the mesh generation of the material microstructure. To obtain a proper...... description of the material microstructure the finite element models must contain a large number of elements and this problem is solved by using the preconditioned conjugated gradient solver with an Element-By-Element preconditioner. Finite element analysis provides the volume averaged stresses and strains...

  14. Interface Properties in Extruded FRC-Materials

    DEFF Research Database (Denmark)

    Stang, Henrik

    1997-01-01

    In a research and development project recently carried out at Department of Structural Engineering and Materials, Technical University of Denmark a new extrusion process for HPFRCC-materials was demonstrated.It is shown that superior interfacial properties are obtained in a polypropylene fiber...... reinforced cementitious material extruded by the developed process. It is further more shown that the fiber-matrix bond is highly dependent on the relative slip at the interface and a bond-slip relationship is suggested for the extruded material. The observed very high fiber-matrix bond is explained...... by the densification of the interfacial matrix material which has taken place during the consolidation process and which can be observed in the thin-section analysis....

  15. Rock Properties Model

    Energy Technology Data Exchange (ETDEWEB)

    C. Lum

    2004-09-16

    The purpose of this model report is to document the Rock Properties Model version 3.1 with regard to input data, model methods, assumptions, uncertainties and limitations of model results, and qualification status of the model. The report also documents the differences between the current and previous versions and validation of the model. The rock properties model provides mean matrix and lithophysae porosity, and the cross-correlated mean bulk density as direct input to the ''Saturated Zone Flow and Transport Model Abstraction'', MDL-NBS-HS-000021, REV 02 (BSC 2004 [DIRS 170042]). The constraints, caveats, and limitations associated with this model are discussed in Section 6.6 and 8.2. Model validation accomplished by corroboration with data not cited as direct input is discussed in Section 7. The revision of this model report was performed as part of activities being conducted under the ''Technical Work Plan for: The Integrated Site Model, Revision 05'' (BSC 2004 [DIRS 169635]). The purpose of this revision is to bring the report up to current procedural requirements and address the Regulatory Integration Team evaluation comments. The work plan describes the scope, objectives, tasks, methodology, and procedures for this process.

  16. Determination of replicate composite bone material properties using modal analysis.

    Science.gov (United States)

    Leuridan, Steven; Goossens, Quentin; Pastrav, Leonard; Roosen, Jorg; Mulier, Michiel; Denis, Kathleen; Desmet, Wim; Sloten, Jos Vander

    2017-02-01

    Replicate composite bones are used extensively for in vitro testing of new orthopedic devices. Contrary to tests with cadaveric bone material, which inherently exhibits large variability, they offer a standardized alternative with limited variability. Accurate knowledge of the composite's material properties is important when interpreting in vitro test results and when using them in FE models of biomechanical constructs. The cortical bone analogue material properties of three different fourth-generation composite bone models were determined by updating FE bone models using experimental and numerical modal analyses results. The influence of the cortical bone analogue material model (isotropic or transversely isotropic) and the inter- and intra-specimen variability were assessed. Isotropic cortical bone analogue material models failed to represent the experimental behavior in a satisfactory way even after updating the elastic material constants. When transversely isotropic material models were used, the updating procedure resulted in a reduction of the longitudinal Young's modulus from 16.00GPa before updating to an average of 13.96 GPa after updating. The shear modulus was increased from 3.30GPa to an average value of 3.92GPa. The transverse Young's modulus was lowered from an initial value of 10.00GPa to 9.89GPa. Low inter- and intra-specimen variability was found. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. 3-D Modeling of Directional Solidification of a Non-Dilute Alloy with Temperature and Concentration Fields Coupling via Materials Properties Dependence and via Double Diffusive Convection

    Science.gov (United States)

    Bune, Andris V.; Gillies, Donald C.; Lehoczky, Sandor L.

    1998-01-01

    Numerical simulation of the HgCdTe growth by the vertical Bridgman method was performed using FIDAP finite element code. Double-diffusive melt convection is analyzed, as the primary factor at controls inhomogeneity of the solidified material. Temperature and concentration fields in the model are also coupled via material properties, such as thermal and solutal expansion coefficients with the dependence on both temperature and concentration, and melting temperature evaluation from pseudobinary CdTe-HgTe phase diagram. Experimental measurements were used to obtain temperature boundary conditions. Parametric study of the melt convection dependence on the gravity conditions was undertaken. It was found, that the maximum convection velocity in the melt can be reduced under certain conditions. Optimal conditions to obtain a near flat solidified interface are discussed. The predicted interface shape is in agreement with one obtained experimentally by quenching. The results of 3-D calculations are compared with previous 2- D findings. A video film featuring 3-D melt convection will be presented.

  18. Influence of muscle activation and mucosal material property on esophageal transport: study based on a fully-resolved computational model

    Science.gov (United States)

    Kou, Wenjun; Pandolfino, John; Kahrilas, Peter; Patankar, Neelesh

    2014-11-01

    Esophageal transport involves interactions between food (bolus), the esophageal walls (composed of mucosal, circular muscle (CM) and longitudinal muscle (LM) layers), and neurally coordinated muscle activation including CM contraction and LM shortening. Due to the complexity of these interactions, few studies have been conducted on the mechanical role of the mucosal layer in esophageal transport. Also poorly understood are the collaborative roles of CM contraction and LM shortening and the influence of their synchronization. Here, based on a fully-resolved computational model that we developed, we investigated the individual roles of CM contraction and LM shortening, compared bolus transport with various levels of discoordination between CM and LM activation, and studied the role of the mucosa and how its stiffening influenced transport. These preliminary findings should help understand the synergy between LM, CM, and the mucosal layer in facilitating bolus transport, thereby providing insight into related physiology and pathophysiology. The support of Grant R01 DK56033 and R01 DK079902 from NIH is gratefully acknowledged.

  19. Material Model Research on Rubber Vibration Isolators

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A viscohyperelastic constitutive model is proposed to describe the mechanical behaviour of vibration isolation rubber under broad-band vibration. This constitutive model comprises two parts: a component with three parameters to characterize the hyperelastic static properties of rubber materials,and the other component incorporating two relaxation time parameters, corresponding to high and low strain rates, respectively, to describe the dynamic response under vibration and impact loadings. Based on this proposed constitutive model, a series of experiments were performed on two types of rubber materials over a wide strain rate range. The results predicted from this model are in good agreement with the experimental data.

  20. Understanding and Predicting the Properties of Complex Materials

    DEFF Research Database (Denmark)

    Smedskjær, Morten Mattrup; Mauro, John C.; Yue, Yuanzheng

    Predicting the properties of new materials prior to manufacturing is a topic attracting great industrial and scientific interest. Mechanical properties are currently of particular interest given the increasing demand for stronger, thinner, and more flexible materials in recent years. Property...... prediction for ceramic materials is facilitated by the periodic short- and long-range order of crystals. Based on J.C. Phillips’s theory for the ionicity of chemical bonding from ~1970, a method for predicting the hardness of covalent crystals was developed in the 2000s, which is now widely applied...... for the design of new superhard ceramic materials. It took another 10 years before the same predictions became possible for glassy systems, in which the lack of long-range order and the long time scales for relaxation greatly complicate the traditional modeling efforts. The key for making progress was to extract...

  1. Interfacing materials models with fire field models

    Energy Technology Data Exchange (ETDEWEB)

    Nicolette, V.F.; Tieszen, S.R.; Moya, J.L.

    1995-12-01

    For flame spread over solid materials, there has traditionally been a large technology gap between fundamental combustion research and the somewhat simplistic approaches used for practical, real-world applications. Recent advances in computational hardware and computational fluid dynamics (CFD)-based software have led to the development of fire field models. These models, when used in conjunction with material burning models, have the potential to bridge the gap between research and application by implementing physics-based engineering models in a transient, multi-dimensional tool. This paper discusses the coupling that is necessary between fire field models and burning material models for the simulation of solid material fires. Fire field models are capable of providing detailed information about the local fire environment. This information serves as an input to the solid material combustion submodel, which subsequently calculates the impact of the fire environment on the material. The response of the solid material (in terms of thermal response, decomposition, charring, and off-gassing) is then fed back into the field model as a source of mass, momentum and energy. The critical parameters which must be passed between the field model and the material burning model have been identified. Many computational issues must be addressed when developing such an interface. Some examples include the ability to track multiple fuels and species, local ignition criteria, and the need to use local grid refinement over the burning material of interest.

  2. Modelling Real Property Transactions

    DEFF Research Database (Denmark)

    Stubkjær, Erik

    2003-01-01

    Der er store forskelle i financieringsomkostningerne ved hussalg i forskellige lande. Er disse forskelle nødvendige? og kan udgifterne reduceres? Sådanne spørgsmål søger forskningsprojektet ?Modelling Real Property Transactions?, officielt sat i værk indenfor rammerne af COST (European Co...

  3. Aerospace Materials Process Modelling

    Science.gov (United States)

    1988-08-01

    deTresca La d~termination du coefficient de frottement de Tresca 9 est effectu~e de facon courante en forgeant un anneau de g~oan~trie fix~e. On mesure la...ailleurs et vaut a= 105 xt 0 , 2 5 Les riductions relatives du diam~tre int~rieur sont report~es sur l1abaque TVM(fig. 2a). Les coefficient de frottement ...validated material data bass. Information such as constitutive equations, intrinsic workability maps, effective heat-transfer coefficients , interface

  4. Global nuclear material control model

    Energy Technology Data Exchange (ETDEWEB)

    Dreicer, J.S.; Rutherford, D.A.

    1996-05-01

    The nuclear danger can be reduced by a system for global management, protection, control, and accounting as part of a disposition program for special nuclear materials. The development of an international fissile material management and control regime requires conceptual research supported by an analytical and modeling tool that treats the nuclear fuel cycle as a complete system. Such a tool must represent the fundamental data, information, and capabilities of the fuel cycle including an assessment of the global distribution of military and civilian fissile material inventories, a representation of the proliferation pertinent physical processes, and a framework supportive of national or international perspective. They have developed a prototype global nuclear material management and control systems analysis capability, the Global Nuclear Material Control (GNMC) model. The GNMC model establishes the framework for evaluating the global production, disposition, and safeguards and security requirements for fissile nuclear material.

  5. Optical properties of photochromic and thermochromic materials

    Science.gov (United States)

    Mo, Yeon-Gon

    The optical properties of some thin film materials can be altered by an external stimulus. Photochromic and thermochromic materials, including inorganic and organic substances, have optical properties that can be changed in a reversible manner by irradiation and temperature respectively. These materials can be used in applications such as radiation or thermal sensors, information storage devices and smart window applications in buildings and cars. In this work, major effort was concentrated on passive thermal control coatings based on photochromic and thermochromic materials. The inorganic photochromic materials were based on tungsten and molybdenum oxide films and the organic photochromic materials included spiropyrans and spirooxazines. In addition, photochromic composite organic-inorganic films and thermochromic vanadium oxide films were prepared. The samples were synthesized using sputtering, sol-gel process, and thermal oxidation. The optical properties were investigated for the first time by ultraviolet/visible/infrared (UV/VIS/IR) spectroscopic ellipsometry, attenuated total reflection (ATR) infrared ellipsometry, spectrophotometry, and X-ray diffraction (XRD). For amorphous oxide films, the oxygen deficiency was important in determining the photochromic properties of the films. In the mid-infrared region, no photochromism was observed for the films. The optical properties of organic-inorganic composite films changed in the VIS/NIR wavelength region markedly in a reversible process, with UV irradiation. The composite films containing tungsten heteropolyoxometalate (HPOM) showed faster coloration and bleaching than pure tungsten oxide films. The composite films with molybdenum HPOM showed faster coloration and much slower bleaching than tungsten HPOM. The spiropyran and spirooxazine doped polymeric films were investigated for the first time using infrared and ATR ellipsometry. The infrared optical functions obtained by ATR measurements were a little smaller

  6. Properties of nanoclay PVA composites materials

    Directory of Open Access Journals (Sweden)

    Mohamed H. M. Ali

    2012-03-01

    Full Text Available Polyvinyl alcohol (PVA/ Na-rich Montmorillonite (MMT nanocomposites were prepared using solution method to create polymer-clay nanocomposite (PCN material. The PCN material was studied using X-ray diffraction (XRD, demonstrating polymer-clay intercalation that has a high d-spacing (lower diffraction angles in the PCN XRD pattern, compared to the pure MMT clay XRD pattern, which has a low d-spacing (high diffraction angles. The nano-scanning electron microscope (NSEM was used to study the morphological image of the PVA, MMT and PCN materials. The results showed that intercalation that took place between the PVA and MMT produced the PCN material. The mechanical properties of the pure PVA and the intercalated polymer material were studied. It was found that the small amount of MMT clay made the tensile modulus and percentage of the total elongation of the nano-composite significantly higher than the pure PVA polymer value, due to polymer-clay intercalation. The thermal stability of the intercalated polymer has been studied using thermal analytical techniques such as thermogravimetric analysis (TGA and differential scanning calorimetry (DSC. The results showed that the PCN material is more thermally stable than the pure PVA polymer.

  7. Modeling mechanical response of heterogeneous materials

    Science.gov (United States)

    Pal, Siladitya

    Heterogeneous materials are ubiquitous in nature and as synthetic materials. These materials provide unique combination of desirable mechanical properties emerging from its heterogeneities at different length scales. Future structural and technological applications will require the development of advanced light weight materials with superior strength and toughness. Cost effective design of the advanced high performance synthetic materials by tailoring their microstructure is the challenge facing the materials design community. Prior knowledge of structure-property relationships for these materials is imperative for optimal design. Thus, understanding such relationships for heterogeneous materials is of primary interest. Furthermore, computational burden is becoming critical concern in several areas of heterogeneous materials design. Therefore, computationally efficient and accurate predictive tools are highly essential. In the present study, we mainly focus on mechanical behavior of soft cellular materials and tough biological material such as mussel byssus thread. Cellular materials exhibit microstructural heterogeneity by interconnected network of same material phase. However, mussel byssus thread comprises of two distinct material phases. A robust numerical framework is developed to investigate the micromechanisms behind the macroscopic response of both of these materials. Using this framework, effect of microstuctural parameters has been addressed on the stress state of cellular specimens during split Hopkinson pressure bar test. A voronoi tessellation based algorithm has been developed to simulate the cellular microstructure. Micromechanisms (microinertia, microbuckling and microbending) governing macroscopic behavior of cellular solids are investigated thoroughly with respect to various microstructural and loading parameters. To understand the origin of high toughness of mussel byssus thread, a Genetic Algorithm (GA) based optimization framework has been

  8. Material Property Characterization of AS4/VRM-34 Textile Laminates

    Science.gov (United States)

    Grenoble, Ray W.; Johnston, William M

    2013-01-01

    Several material properties (modulus, strengths, and fracture toughness) of a textile composite have been evaluated to provide input data to analytical models of Pultruded Rod Stiffened Efficient Unitized Structure (PRSEUS). The material system is based on warp-knitted preforms of AS4 carbon fibers and VRM-34 epoxy resin, which have been processed via resin infusion and oven curing. Tensile, compressive, shear, and fracture toughness properties have been measured at ambient and elevated temperatures. All specimens were tested in as-fabricated (dry) condition. Specimens were tested with and without through-thickness stitching.

  9. Micro-mechanical modeling of the cement-bone interface: the effect of friction morphology and material properties on the micromechanical response

    NARCIS (Netherlands)

    Janssen, Dennis; Mann, Kenneth A.; Verdonschot, Nicolaas Jacobus Joseph

    2008-01-01

    In order to gain insight into the micro-mechanical behavior of the cement–bone interface, the effect of parametric variations of frictional, morphological and material properties on the mechanical response of the cement–bone interface were analyzed using a finite element approach. Finite element

  10. Development and Demonstration of Material Properties Database and Software for the Simulation of Flow Properties in Cementitious Materials

    Energy Technology Data Exchange (ETDEWEB)

    Smith, F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Flach, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-03-30

    This report describes work performed by the Savannah River National Laboratory (SRNL) in fiscal year 2014 to develop a new Cementitious Barriers Project (CBP) software module designated as FLOExcel. FLOExcel incorporates a uniform database to capture material characterization data and a GoldSim model to define flow properties for both intact and fractured cementitious materials and estimate Darcy velocity based on specified hydraulic head gradient and matric tension. The software module includes hydraulic parameters for intact cementitious and granular materials in the database and a standalone GoldSim framework to manipulate the data. The database will be updated with new data as it comes available. The software module will later be integrated into the next release of the CBP Toolbox, Version 3.0. This report documents the development efforts for this software module. The FY14 activities described in this report focused on the following two items that form the FLOExcel package; 1) Development of a uniform database to capture CBP data for cementitious materials. In particular, the inclusion and use of hydraulic properties of the materials are emphasized; and 2) Development of algorithms and a GoldSim User Interface to calculate hydraulic flow properties of degraded and fractured cementitious materials. Hydraulic properties are required in a simulation of flow through cementitious materials such as Saltstone, waste tank fill grout, and concrete barriers. At SRNL these simulations have been performed using the PORFLOW code as part of Performance Assessments for salt waste disposal and waste tank closure.

  11. Surface effects on the mechanical properties of nanoporous materials

    Energy Technology Data Exchange (ETDEWEB)

    Xia Re [School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072 (China); Li Xide; Feng Xiqiao [AML, Department of Engineering Mechanics, Tsinghua University, Beijing 100084 (China); Qin Qinghua [School of Engineering, Australian National University, Canberra, ACT 0200 (Australia); Liu Jianlin, E-mail: fengxq@tsinghua.edu.cn [Department of Engineering Mechanics, China University of Petroleum, Qingdao 266555 (China)

    2011-07-01

    Using the theory of surface elasticity, we investigate the mechanical properties of nanoporous materials. The classical theory of porous materials is modified to account for surface effects, which become increasingly important as the characteristic sizes of microstructures shrink to nanometers. First, a refined Timoshenko beam model is presented to predict the effective elastic modulus of nanoporous materials. Then the surface effects on the elastic microstructural buckling behavior of nanoporous materials are examined. In particular, nanoporous gold is taken as an example to illustrate the application of the proposed model. The results reveal that both the elastic modulus and the critical buckling behavior of nanoporous materials exhibit a distinct dependence on the characteristic sizes of microstructures, e.g. the average ligament width.

  12. Quality quantification model of basic raw materials

    Directory of Open Access Journals (Sweden)

    Š. Vilamová

    2016-07-01

    Full Text Available Basic raw materials belong to the key input sources in the production of pig iron. The properties of basic raw materials can be evaluated using a variety of criteria. The essential ones include the physical and chemical properties. Current competitive pressures, however, force the producers of iron more and more often to include cost and logistic criteria into the decision-making process. In this area, however, they are facing a problem of how to convert a variety of vastly different parameters into one evaluation indicator in order to compare the available raw materials. This article deals with the analysis of a model created to evaluate the basic raw materials, which was designed as part of the research.

  13. Identification of the viscoelastic properties of soft materials at low frequency: performance, ill-conditioning and extrapolation capabilities of fractional and exponential models.

    Science.gov (United States)

    Ciambella, J; Paolone, A; Vidoli, S

    2014-09-01

    We report about the experimental identification of viscoelastic constitutive models for frequencies ranging within 0-10Hz. Dynamic moduli data are fitted forseveral materials of interest to medical applications: liver tissue (Chatelin et al., 2011), bioadhesive gel (Andrews et al., 2005), spleen tissue (Nicolle et al., 2012) and synthetic elastomer (Osanaiye, 1996). These materials actually represent a rather wide class of soft viscoelastic materials which are usually subjected to low frequencies deformations. We also provide prescriptions for the correct extrapolation of the material behavior at higher frequencies. Indeed, while experimental tests are more easily carried out at low frequency, the identified viscoelastic models are often used outside the frequency range of the actual test. We consider two different classes of models according to their relaxation function: Debye models, whose kernel decays exponentially fast, and fractional models, including Cole-Cole, Davidson-Cole, Nutting and Havriliak-Negami, characterized by a slower decay rate of the material memory. Candidate constitutive models are hence rated according to the accurateness of the identification and to their robustness to extrapolation. It is shown that all kernels whose decay rate is too fast lead to a poor fitting and high errors when the material behavior is extrapolated to broader frequency ranges.

  14. Identification of material properties of sandwich structure with piezoelectric patches

    Directory of Open Access Journals (Sweden)

    Zemčík R.

    2008-11-01

    Full Text Available The work focuses on light-weight sandwich structures made of carbon-epoxy skins and foam core which have unique bending stiffness compared to conventional materials. The skins are manufactured by vacuum autoclave technology from unidirectional prepregs and the sandwich is then glued together. The resulting material properties of the structure usually differ from those provided by manufacturer or even those obtained from experimental tests on separate materials, which makes computational models unreliable. Therefore, the properties are identified using the combination of experimental analysis of the sandwich with attached piezoelectric transducer and corresponding static and modal finite element analyses. Simple mathematical optimization with repetitive finite element solution is used. The model is then verified by transient analysis when the piezoelectric patch is excited by harmonic signals covering the first two eigen-frequencies and the induced oscillations are measured by laser sensor.

  15. AGC 2 Irradiated Material Properties Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Rohrbaugh, David Thomas [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2017-05-01

    The Advanced Reactor Technologies Graphite Research and Development Program is conducting an extensive graphite irradiation experiment to provide data for licensing of a high temperature reactor (HTR) design. In past applications, graphite has been used effectively as a structural and moderator material in both research and commercial high temperature gas cooled reactor designs. , Nuclear graphite H 451, used previously in the United States for nuclear reactor graphite components, is no longer available. New nuclear graphite grades have been developed and are considered suitable candidates for new HTR reactor designs. To support the design and licensing of HTR core components within a commercial reactor, a complete properties database must be developed for these current grades of graphite. Quantitative data on in service material performance are required for the physical, mechanical, and thermal properties of each graphite grade, with a specific emphasis on data accounting for the life limiting effects of irradiation creep on key physical properties of the HTR candidate graphite grades. Further details on the research and development activities and associated rationale required to qualify nuclear grade graphite for use within the HTR are documented in the graphite technology research and development plan.

  16. Synthesis of new materials with properties ameliorated

    Science.gov (United States)

    Baira, F.; Benfarhi, S.; Zidani, S.

    2012-09-01

    Cellulose is the most abundant polymer in nature. It is used mainly for the production of paper bet also as a reinforcement in the polymer matrixes[1]. The modification of this polysaccharide presents a great interest, for it is the main constituent of agricultural wastes. It is well known that the microcrystalline cellulose gives, after chemical modification, new biodegradable materials[2], which may be used, for instance, for packaging. The esterification of cellulose necessitates an acid pretreatment which makes hydroxyl groups more accessible by breaking hydrogen bonds. X-rays diffraction analysis showed a feeble diminution of the treated samples cristallinity[3]. Cellulose, activated in this way, is esterified in a classic way in DMF, in the presence of triethylamine, LiCl and acid chloride at 60C° for 24 hours[4]. The obtained ester is precipitated in MeOH. The residue, dissolved in CHCl3, gives after evaporation in the open air, a plastic film surface. The water drop test has shown the hydrophobe properties of the plastic film surface. Our work is the study of the preparation of composite materials from the basis of their derivatives. Well as the study of the photopolymerisation kinetic, and the chemical degradation. The obtained films were analyzed by IR-TF, and the volumetrie[5,6]. As a conclusion, we have prepared composite materials with improved properties with reference to the matrix alone.

  17. Wear Property of Cast Steel Wheel Material in Rail Truck

    Institute of Scientific and Technical Information of China (English)

    MI Guo-fa; LIU Yan-lei; ZHANG Bin; FU Xiu-qin; ZHANG Hong; SONG Guo-xiang

    2009-01-01

    Wear property of material plays a key role in the service time of workpiece.A major objective in the development of new wheel materials is to improve the wear performance.The wear property of B and B+ grade cast steel materials was reported.The results showed that B+ grade cast steel material exhibited better wear property than the B grade material.Carbon content related to the hardness match was the principal factor affecting the wear properties.

  18. Homogenization for Periodic Heterogeneous Materials with Arbitrary Position-Dependent Material Properties

    Institute of Scientific and Technical Information of China (English)

    徐志杰

    2012-01-01

    We present a rigorous homogenization approach for elcient computation of a class of physical problems in a one-dimensional periodic heterogeneous material. This material is represented by a spatially periodic array of unit cells with a length of More specifically, the method is applied to the diffusion, heat conduction, and wave propagation problems. Heterogeneous materials can have arbitrary position-dependent continuous or discontinuous materials properties (for example heat conductivity) within the unit cell. The final effective model includes both effective properties at the leading order and high-order contributions due to the microscopic heterogeneity. A dimensionless heterogeneity parameter ~ is defined to represent high-order contributions, shown to be in the range of [-1/12, 0], and has a universal expression for all three problems. Both effective properties and heterogeneity parameter 13 are independent oft, the microscopic scale of heterogeneity. The homogenized solution describing macroscopic variations can be obtained from the effective model. Solution with sub-unit-cell accuracy can be constructed based on the homogenized solution and its spatial derivatives. The paper represents a general approach to obtain the effective model for arbitrary periodic heterogeneous materials with position-dependent properties.

  19. Fundamentals of semiconductors physics and materials properties

    CERN Document Server

    Yu, Peter Y

    1996-01-01

    Fundamentals of Semiconductors attempts to fill the gap between a general solid-state physics textbook and research articles by providing detailed explanations of the electronic, vibrational, transport, and optical properties of semiconductors The approach is physical and intuitive rather than formal and pedantic Theories are presented to explain experimental results This textbook has been written with both students and researchers in mind Its emphasis is on understanding the physical properties of Si and similar tetrahedrally coordinated semiconductors The explanations are based on physical insights Each chapter is enriched by an extensive collection of tables of material parameters, figures and problems Many of these problems 'lead the student by the hand' to arrive at the results

  20. Fundamentals of semiconductors physics and materials properties

    CERN Document Server

    Yu, Peter Y

    2010-01-01

    This fourth edition of the well-established Fundamentals of Semiconductors serves to fill the gap between a general solid-state physics textbook and research articles by providing detailed explanations of the electronic, vibrational, transport, and optical properties of semiconductors. The approach is physical and intuitive rather than formal and pedantic. Theories are presented to explain experimental results. This textbook has been written with both students and researchers in mind. Its emphasis is on understanding the physical properties of Si and similar tetrahedrally coordinated semiconductors. The explanations are based on physical insights. Each chapter is enriched by an extensive collection of tables of material parameters, figures, and problems. Many of these problems "lead the student by the hand" to arrive at the results. The major changes made in the fourth edition include: an extensive appendix about the important and by now well-established deep center known as the DX center, additional problems...

  1. Thermal Radiative Properties of Xonotlite Insulation Material

    Institute of Scientific and Technical Information of China (English)

    Xinxin ZHANG; Gaosheng WEI; Fan YU

    2005-01-01

    This paper presents experimental results of thermal radiative properties of xonotlite-type calcium silicate insulation material. Transmittance spectra were first taken using Fourier transform infrared spectrometer (FTIR)for the samples with ρ = 234 kg/m3. Specific extinction coefficient spectra were then obtained by applying Beer's law.Finally,by using the diffusion approximation,the specific Rossland mean extinction coefficients and radiative thermal conductivities were obtained for various temperatures. The results show that the specific spectral extinction coefficient of xonotlite is larger than 7 m2/kg in the whole measured spectra, and diffusion approximation equation is a reasonable description of radiative heat transfer in xonotlite insulation material. The specific Rossland mean extinction coefficient of xonotlite has a maximum ualue at 400 K and the radiative thermal conductivity is almost proportional to the cube of temperature.

  2. Photorefractive optics materials, properties, and applications

    CERN Document Server

    Yu, Francis T S

    1999-01-01

    The advances of photorefractive optics have demonstrated many useful and practical applications, which include the development of photorefractive optic devices for computer communication needs. To name a couple significant applications: the large capacity optical memory, which can greatly improve the accessible high-speed CD-ROM and the dynamic photorefractive gratings, which can be used for all-optic switches for high-speed fiber optic networks. This book is an important reference both for technical and non-technical staffs who are interested in this field. * Covers the recent development in materials, phenomena, and applications * Includes growth, characterization, dynamic gratings, and liquid crystal PR effect * Includes applications to photonic devices such as large capacity optical memory, 3-D interconnections, and dynamic holograms * Provides the recent overall picture of current trends in photorefractive optics * Includes optical and electronic properties of the materials as applied to dynamic photoref...

  3. Material properties of the plantar aponeurosis.

    Science.gov (United States)

    Kitaoka, H B; Luo, Z P; Growney, E S; Berglund, L J; An, K N

    1994-10-01

    Material properties of the plantar aponeurosis were determined by a two-dimensional video tracking method to simultaneously measure the aponeurosis deformation. Failure loads averaged 1189 +/- 244 N and were higher in men. Average stiffness of the intact fascia was 203.7 +/- 50.5 N/mm at a loading rate of 11.12 N/sec and it did not vary significantly for the loading rates of 11.12 to 1112 N/sec. The high tensile loads required for failure were consistent with clinical and biomechanical studies and indicated the importance of the aponeurosis in foot function and arch stability.

  4. Characterization of mechanical properties of materials using ultrasound broadband spectroscopy.

    Science.gov (United States)

    Agrawal, Megha; Prasad, Abhinav; Bellare, Jayesh R; Seshia, Ashwin A

    2016-01-01

    This article explores the characterization of homogenous materials (metals, alloys, glass and polymers) by a simple broadband ultrasonic interrogation method. The novelty lies in the use of ultrasound in a continuous way with very low input power (0 dBm or less) and analysis of the transmitted acoustic wave spectrum for material property characterization like speed of sound, density and dimensions of a material. Measurements were conducted on various thicknesses of samples immersed in liquid where continuous-wave, frequency swept ultrasonic energy was incident normal to the sample surface. The electro-acoustic transmission response is analyzed in the frequency domain with respect to a specifically constructed multi-layered analytical model. From the acoustic signature of the sample materials, material properties such as speed of sound and acoustic impedance can be calculated with experimentally derived values found to be in general agreement with the literature and with pulse-echo technique establishing the basis for a non-contact and non-destructive technique for material characterization. Further, by looking at the frequency spacing of the peaks of water when the sample is immersed, the thickness of the sample can be calculated independently from the acoustic response. This technique can prove to be an effective non-contact, non-destructive and fast material characterization technique for a wide variety of materials.

  5. Numerical modeling in materials science and engineering

    CERN Document Server

    Rappaz, Michel; Deville, Michel

    2003-01-01

    This book introduces the concepts and methodologies related to the modelling of the complex phenomena occurring in materials processing. After a short reminder of conservation laws and constitutive relationships, the authors introduce the main numerical methods: finite differences, finite volumes and finite elements. These techniques are developed in three main chapters of the book that tackle more specific problems: phase transformation, solid mechanics and fluid flow. The two last chapters treat inverse methods to obtain the boundary conditions or the material properties and stochastic methods for microstructural simulation. This book is intended for undergraduate and graduate students in materials science and engineering, mechanical engineering and physics and for engineering professionals or researchers who want to get acquainted with numerical simulation to model and compute materials processing.

  6. Symposium DD: Low-Dimensional Materials-Synthesis, Assembly, Property Scaling and Modeling. Held in San Francisco, CA on April 9-13, 2007

    Science.gov (United States)

    2008-06-01

    quantum dots are exquisitely sensitive to extra charges. As for electrochromic materials, the optical absorption is directly modified by state filling...University, Daejeon, South Korea. Layer-by-layer( LbL ) self-assembly is a template-assisted process in which charge reversal techniques using...allows consecutive thin film deposition to proceed via the electrostatic LbL method. The persistence length is a basic property quantifying the stiffness

  7. Catastrophic models of materials destruction

    OpenAIRE

    Kupchishin, A. I.; Taipova, B. G.; A. A. Kupchishin; Voronova, N. A.; Kirdyashkin, V. I.; Fursa, Tatyana Viktorovna

    2016-01-01

    The effect of concentration and type of fillers on mechanical properties of composite material based on polyimide were studied. Polyethylene terephthalate (PET, polyester), polycarbonate (PCAR) and montmorillonite (MM) were used as the fillers. The samples were prepared by mechanically blending the polyimide-based lacquer solutions with different concentrations of the second component. The concentration of filler and its class, especially their internal structure and technology of synthesis d...

  8. Exploring the interdependencies between parameters in a material model.

    Energy Technology Data Exchange (ETDEWEB)

    Silling, Stewart Andrew; Fermen-Coker, Muge

    2014-01-01

    A method is investigated to reduce the number of numerical parameters in a material model for a solid. The basis of the method is to detect interdependencies between parameters within a class of materials of interest. The method is demonstrated for a set of material property data for iron and steel using the Johnson-Cook plasticity model.

  9. A novel underuse model shows that inactivity but not ovariectomy determines the deteriorated material properties and geometry of cortical bone in the tibia of adult rats.

    Science.gov (United States)

    Miyagawa, Kazuaki; Kozai, Yusuke; Ito, Yumi; Furuhama, Takami; Naruse, Kouji; Nonaka, Kiichi; Nagai, Yumiko; Yamato, Hideyuki; Kashima, Isamu; Ohya, Keiichi; Aoki, Kazuhiro; Mikuni-Takagaki, Yuko

    2011-07-01

    Our goal in this study was to determine to what extent the physiologic consequences of ovariectomy (OVX) in bones are exacerbated by a lack of daily activity such as walking. We forced 14-week-old female rats to be inactive for 15 weeks with a unique experimental system that prevents standing and walking while allowing other movements. Tibiae, femora, and 4th lumbar vertebrae were analyzed by peripheral quantitative computed tomography (pQCT), microfocused X-ray computed tomography (micro-CT), histology, histomorphometry, Raman spectroscopy, and the three-point bending test. Contrary to our expectation, the exacerbation was very much limited to the cancellous bone parameters. Parameters of femur and tibia cortical bone were affected by the forced inactivity but not by OVX: (1) cross-sectional moment of inertia was significantly smaller in Sham-Inactive rat bones than that of their walking counterparts; (2) the number of sclerostin-positive osteocytes per unit cross-sectional area was larger in Sham-Inactive rat bones than in Sham-Walking rat bones; and (3) material properties such as ultimate stress of inactive rat tibia was lower than that of their walking counterparts. Of note, the additive effect of inactivity and OVX was seen only in a few parameters, such as the cancellous bone mineral density of the lumbar vertebrae and the structural parameters of cancellous bone in the lumbar vertebrae/tibiae. It is concluded that the lack of daily activity is detrimental to the strength and quality of cortical bone in the femur and tibia of rats, while lack of estrogen is not. Our inactive rat model, with the older rats, will aid the study of postmenopausal osteoporosis, the etiology of which may be both hormonal and mechanical.

  10. Development and Analysis of Synthetic Composite Materials Emulating Patient AAA Wall Material Properties

    Science.gov (United States)

    Margossian, Christa M.

    Abdominal Aortic Aneurysm (AAA) rupture accounts for 14,000 deaths a year in the United States. Since the number of ruptures has not decreased significantly in recent years despite improvements in imaging and surgical procedures, there is a need for an accurate, noninvasive technique capable of establishing rupture risk for specific patients and discriminating lesions at high risk. In this project, synthetic composite materials replicating patient-specific wall stiffness and strength were developed and their material properties evaluated. Composites utilizing various fibers were developed to give a range of stiffness from 1825.75 kPa up through 8187.64 kPa with one base material, Sylgard 170. A range of strength from 631.12 kPa to 1083 kPa with the same base material was also found. By evaluating various base materials and various reinforcing fibers, a catalogue of stiffnesses and strengths was started to allow for adaptation to specific patient properties. Three specific patient properties were well-matched with two composites fabricated: silk thread-reinforced Sylgard 170 and silk thread-reinforced Dragon Skin 20. The composites showed similar stiffnesses to the specific patients while reaching target stresses at particular strains. Not all patients were matched with composites as of yet, but recommendations for future matches are able to be determined. These composites will allow for the future evaluation of flow-induced wall stresses in models replicating patient material properties and geometries.

  11. Constitutive modeling for isotropic materials

    Science.gov (United States)

    Chan, K. S.; Lindholm, U. S.; Bodner, S. R.

    1988-01-01

    The third and fourth years of a 4-year research program, part of the NASA HOST Program, are described. The program goals were: (1) to develop and validate unified constitutive models for isotropic materials, and (2) to demonstrate their usefulness for structural analysis of hot section components of gas turbine engines. The unified models selected for development and evaluation were those of Bodner-Partom and of Walker. The unified approach for elastic-viscoplastic constitutive equations is a viable method for representing and predicting material response characteristics in the range where strain rate and temperature dependent inelastic deformations are experienced. This conclusion is reached by extensive comparison of model calculations against the experimental results of a test program of two high temperature Ni-base alloys, B1900+Hf and Mar-M247, over a wide temperature range for a variety of deformation and thermal histories including uniaxial, multiaxial, and thermomechanical loading paths. The applicability of the Bodner-Partom and the Walker models for structural applications has been demonstrated by implementing these models into the MARC finite element code and by performing a number of analyses including thermomechanical histories on components of hot sections of gas turbine engines and benchmark notch tensile specimens. The results of the 4-year program have been published in four annual reports. The results of the base program are summarized in this report. The tasks covered include: (1) development of material test procedures, (2) thermal history effects, and (3) verification of the constitutive model for an alternative material.

  12. Modeling Bamboo as a Functionally Graded Material

    Science.gov (United States)

    Silva, Emílio Carlos Nelli; Walters, Matthew C.; Paulino, Glaucio H.

    2008-02-01

    Natural fibers are promising for engineering applications due to their low cost. They are abundantly available in tropical and subtropical regions of the world, and they can be employed as construction materials. Among natural fibers, bamboo has been widely used for housing construction around the world. Bamboo is an optimized composite material which exploits the concept of Functionally Graded Material (FGM). Biological structures, such as bamboo, are composite materials that have complicated shapes and material distribution inside their domain, and thus the use of numerical methods such as the finite element method and multiscale methods such as homogenization, can help to further understanding of the mechanical behavior of these materials. The objective of this work is to explore techniques such as the finite element method and homogenization to investigate the structural behavior of bamboo. The finite element formulation uses graded finite elements to capture the varying material distribution through the bamboo wall. To observe bamboo behavior under applied loads, simulations are conducted considering a spatially-varying Young's modulus, an averaged Young's modulus, and orthotropic constitutive properties obtained from homogenization theory. The homogenization procedure uses effective, axisymmetric properties estimated from the spatially-varying bamboo composite. Three-dimensional models of bamboo cells were built and simulated under tension, torsion, and bending load cases.

  13. Thermophysical Property Models for Lunar Regolith

    Science.gov (United States)

    Schreiner, Samuel S.; Dominguez, Jesus A.; Sibille, Laurent; Hoffman, Jeffrey A.

    2015-01-01

    We present a set of models for a wide range of lunar regolith material properties. Data from the literature are t with regression models for the following regolith properties: composition, density, specific heat, thermal conductivity, electrical conductivity, optical absorption length, and latent heat of melting/fusion. These models contain both temperature and composition dependencies so that they can be tailored for a range of applications. These models can enable more consistent, informed analysis and design of lunar regolith processing hardware. Furthermore, these models can be utilized to further inform lunar geological simulations. In addition to regression models for each material property, the raw data is also presented to allow for further interpretation and fitting as necessary.

  14. Investigation of Effective Material Properties of Stony Meteorites

    Science.gov (United States)

    Agrawal, Parul; Carlozzi, Alex; Bryson, Kathryn

    2016-01-01

    To assess the threat posed by an asteroid entering Earth's atmosphere, one must predict if, when, and how it fragments during entry. A comprehensive understanding of the Asteroid material properties is needed to achieve this objective. At present, the meteorite material found on Earth are the only objects from an entering asteroid that can be used as representative material and be tested inside a laboratory setting. Therefore, unit cell models are developed to determine the effective material properties of stony meteorites and in turn deduce the properties of asteroids. The unit cell is representative volume that accounts for diverse minerals, porosity, and matrix composition inside a meteorite. The various classes under investigation includes H-class, L-class, and LL-class chondrites. The effective mechanical properties such as Young's Modulus and Poisson's Ratio of the unit cell are calculated by performing several hundreds of Monte-Carlo simulations. Terrestrial analogs such as Basalt and Gabbro are being used to validate the unit cell methodology.

  15. Interdisciplinary research on the nature and properties of ceramic materials

    Science.gov (United States)

    1980-01-01

    The advancement of material performance and design methodology as related to brittle materials was investigated. The processing and properties of ceramic materials as related to design requirements was also studied.

  16. Thermophysical Properties of Selected Aerospace Materials. Part 2. Thermophysical Properties of Seven Materials

    Science.gov (United States)

    1977-01-01

    Determining Thermal Conductivity of Solids from 20 to 600 K," Cryogenics, 5( 1), 17-20, 1965. 11. Garth, R.C. and Sailer , V.L., "Thermal Conductivity of...34Thermal Property Data Utilized for Asset Materials," McDonnell Aircraft Corp. Rept. A656, 45 pp., 1964. [AD 480 414] 23. Makarounls, O., " Solar

  17. Properties of Sealing Materials in Groundwater Wells

    DEFF Research Database (Denmark)

    Köser, Claus

    on the maximum swelling pressure; i) the bulk density of the sample, and ii) whether the sample is sorted or unsorted. CT scans (Computed Tomography) have been used to evaluate certain properties of bentonite seals in a limited volume. In this context, a set of algorithms to convert CT numbers (HU unit......) into densities for clay/water systems has been developed. This method has successfully been used to evaluate e.g., macroporosity, homogenization of the bentonite seal during the hydration of water, hydraulic conductivity and the creation of channels in the bentonite seals. Based on the results obtained...... in this Ph.D. thesis, a number of recommendations has been offered; i) a change regarding the production of pellets and ii) how sealing material must be treated in the actual construction of groundwater wells....

  18. Bone Material Properties in Osteogenesis Imperfecta.

    Science.gov (United States)

    Bishop, Nick

    2016-04-01

    Osteogenesis imperfecta entrains changes at every level in bone tissue, from the disorganization of the collagen molecules and mineral platelets within and between collagen fibrils to the macroarchitecture of the whole skeleton. Investigations using an array of sophisticated instruments at multiple scale levels have now determined many aspects of the effect of the disease on the material properties of bone tissue. The brittle nature of bone in osteogenesis imperfecta reflects both increased bone mineralization density-the quantity of mineral in relation to the quantity of matrix within a specific bone volume-and altered matrix-matrix and matrix mineral interactions. Contributions to fracture resistance at multiple scale lengths are discussed, comparing normal and brittle bone. Integrating the available information provides both a better understanding of the effect of current approaches to treatment-largely improved architecture and possibly some macroscale toughening-and indicates potential opportunities for alternative strategies that can influence fracture resistance at longer-length scales.

  19. Spacecraft dielectric material properties and spacecraft charging

    Science.gov (United States)

    Frederickson, A. R.; Wall, J. A.; Cotts, D. B.; Bouquet, F. L.

    1986-01-01

    The physics of spacecraft charging is reviewed, and criteria for selecting and testing semiinsulating polymers (SIPs) to avoid charging are discussed and illustrated. Chapters are devoted to the required properties of dielectric materials, the charging process, discharge-pulse phenomena, design for minimum pulse size, design to prevent pulses, conduction in polymers, evaluation of SIPs that might prevent spacecraft charging, and the general response of dielectrics to space radiation. SIPs characterized include polyimides, fluorocarbons, thermoplastic polyesters, poly(alkanes), vinyl polymers and acrylates, polymers containing phthalocyanine, polyacene quinones, coordination polymers containing metal ions, conjugated-backbone polymers, and 'metallic' conducting polymers. Tables summarizing the results of SIP radiation tests (such as those performed for the NASA Galileo Project) are included.

  20. Simulated Analysis of Dielectric Properties of Heterogeneous Materials

    Directory of Open Access Journals (Sweden)

    Yang Biao

    2016-01-01

    Full Text Available The present paper reports the results of a numerical analysis of two phases lossless heterogeneous materials based on a three dimensional (3-D random dielectric mixture. The effective permittivity of a 3-D dielectric materials is calculated by the S-parameter retrieval method and finite element method. The calculated effective permittivity is in good agreement with theoretical models by compared with Bruggeman formula and Coherent potential formula, showing that the volume fraction of inclusions is increasing, the effective permittivity increases with radiation frequency and appear an imaginary part taking on the dielectric loss properties.

  1. Mechanical properties of low dimensional materials

    Science.gov (United States)

    Saini, Deepika

    Recent advances in low dimensional materials (LDMs) have paved the way for unprecedented technological advancements. The drive to reduce the dimensions of electronics has compelled researchers to devise newer techniques to not only synthesize novel materials, but also tailor their properties. Although micro and nanomaterials have shown phenomenal electronic properties, their mechanical robustness and a thorough understanding of their structure-property relationship are critical for their use in practical applications. However, the challenges in probing these mechanical properties dramatically increase as their dimensions shrink, rendering the commonly used techniques inadequate. This dissertation focuses on developing techniques for accurate determination of elastic modulus of LDMs and their mechanical responses under tensile and shear stresses. Fibers with micron-sized diameters continuously undergo tensile and shear deformations through many phases of their processing and applications. Significant attention has been given to their tensile response and their structure-tensile properties relations are well understood, but the same cannot be said about their shear responses or the structure-shear properties. This is partly due to the lack of appropriate instruments that are capable of performing direct shear measurements. In an attempt to fill this void, this dissertation describes the design of an inexpensive tabletop instrument, referred to as the twister, which can measure the shear modulus (G) and other longitudinal shear properties of micron-sized individual fibers. An automated system applies a pre-determined twist to the fiber sample and measures the resulting torque using a sensitive optical detector. The accuracy of the instrument was verified by measuring G for high purity copper and tungsten fibers. Two industrially important fibers, IM7 carbon fiber and KevlarRTM 119, were found to have G = 17 and 2.4 GPa, respectively. In addition to measuring the shear

  2. Modelling Hospital Materials Management Processes

    Directory of Open Access Journals (Sweden)

    Raffaele Iannone

    2013-06-01

    integrated and detailed analysis and description model for hospital materials management data and tasks, which is able to tackle information from patient requirements to usage, from replenishment requests to supplying and handling activities. The model takes account of medical risk reduction, traceability and streamlined processes perspectives. Second, the paper translates this information into a business process model and mathematical formalization.The study provides a useful guide to the various relevant technology‐related, management and business issues, laying the foundations of an efficient reengineering of the supply chain to reduce healthcare costs and improve the quality of care.

  3. Magnetic Properties of Nanoparticles of Antiferromagnetic Materials

    DEFF Research Database (Denmark)

    Mørup, Steen; Frandsen, Cathrine; Bødker, Franz

    2003-01-01

    The magnetic properties of antiferromagnetic nanoparticles have been studied by Mossbauer spectroscopy and neutron scattering. Temperature series of Mossbauer spectra of non-interacting, superparamagnetic hematite nanoparticles were fitted by use of the Blume-Tjon relaxation model. It has been...... found that the magnetic anisotropy energy constant increases significantly with decreasing particle size. Neutron scattering experiments on similar samples give new information on both superparamagnetic relaxation and collective magnetic excitations. There is good agreement between the values...... of the parameters obtained from Mossbauer spectroscopy and neutron scattering. In samples of interacting hematite nanoparticles, the relaxation was significantly suppressed. The Mossbauer data for these samples are in accordance with a mean field model for an ordered state of strongly interacting particles. Mixing...

  4. Viscoelastic models for explosive binder materials

    Energy Technology Data Exchange (ETDEWEB)

    Bardenhagen, S.G.; Harstad, E.N.; Maudlin, P.J.; Gray, G.T. [Los Alamos National Lab., NM (United States); Foster, J.C. Jr. [Wright Lab., Eglin AFB, FL (United States)

    1997-07-01

    An improved model of the mechanical properties of the explosive contained in conventional munitions is needed to accurately simulate performance and accident scenarios in weapons storage facilities. A specific class of explosives can he idealized as a mixture of two components: energetic crystals randomly suspended in a polymeric matrix (binder). Strength characteristics of each component material are important in the macroscopic behavior of the composite (explosive). Of interest here is the determination of an appropriate constitutive law for a polyurethane binder material. This paper is a continuation of previous work in modeling polyurethane at moderately high strain rates and for large deformations. Simulation of a large deformation (strains in excess of 100%) Taylor Anvil experiment revealed numerical difficulties which have been addressed. Additional experimental data have been obtained including improved resolution Taylor Anvil data, and stress relaxation data at various strain rates. A thorough evaluation of the candidate viscoelastic constitutive model is made and possible improvements discussed.

  5. SATURATED - UNSATURATED HYDRAULIC PROPERTIES OF SUBBASE COURSE MATERIAL AND SUBGRADE SOIL

    Science.gov (United States)

    Yano, Takao; Nishiyama, Satoshi; Nakashima, Shin-Ichiro; Moriishi, Kazushi; Ohnishi, Yuzo

    In order to evaluate the rainwate r storage and infiltration properties of the permeable pavement by unsaturated seepage analysis or gas-liquid two-phase flow analysis, it is important to know the unsaturated hydraulic properties of materials wh ich constitute the pavement. For this reason, we showed the unsaturated hydraulic properties of porous asphalt material s but we have not clarified the relation between the performance of the permeable pavement and the properties of all constituti on materials. In this paper, we try to determine the unsaturated hydraulic properties of subbase course and subgrade materials that greatly affect the rainwater storage and infiltration properties of the permeable pavement. We show from experiments that water retention characteristic and the un saturated hydraulic properties of subbase course and subgrade materials well match the van Genuchten model and the Irmay model.

  6. Effective Materials Property Information Management for the 21st Century

    Science.gov (United States)

    Ren, Weiju; Cebon, David; Arnold, Steve

    2009-01-01

    This paper discusses key principles for the development of materials property information management software systems. There are growing needs for automated materials information management in various organizations. In part these are fueled by the demands for higher efficiency in material testing, product design and engineering analysis. But equally important, organizations are being driven by the need for consistency, quality and traceability of data, as well as control of access to sensitive information such as proprietary data. Further, the use of increasingly sophisticated nonlinear, anisotropic and multi-scale engineering analyses requires both processing of large volumes of test data for development of constitutive models and complex materials data input for Computer-Aided Engineering (CAE) software. And finally, the globalization of economy often generates great needs for sharing a single "gold source" of materials information between members of global engineering teams in extended supply chains. Fortunately, material property management systems have kept pace with the growing user demands and evolved to versatile data management systems that can be customized to specific user needs. The more sophisticated of these provide facilities for: (i) data management functions such as access, version, and quality controls; (ii) a wide range of data import, export and analysis capabilities; (iii) data "pedigree" traceability mechanisms; (iv) data searching, reporting and viewing tools; and (v) access to the information via a wide range of interfaces. In this paper the important requirements for advanced material data management systems, future challenges and opportunities such as automated error checking, data quality characterization, identification of gaps in datasets, as well as functionalities and business models to fuel database growth and maintenance are discussed.

  7. Effective Materials Property Information Management for the 21st Century

    Science.gov (United States)

    Ren, Weiju; Cebon, David; Arnold, Steve

    2009-01-01

    This paper discusses key principles for the development of materials property information management software systems. There are growing needs for automated materials information management in various organizations. In part these are fueled by the demands for higher efficiency in material testing, product design and engineering analysis. But equally important, organizations are being driven by the need for consistency, quality and traceability of data, as well as control of access to sensitive information such as proprietary data. Further, the use of increasingly sophisticated nonlinear, anisotropic and multi-scale engineering analyses requires both processing of large volumes of test data for development of constitutive models and complex materials data input for Computer-Aided Engineering (CAE) software. And finally, the globalization of economy often generates great needs for sharing a single "gold source" of materials information between members of global engineering teams in extended supply chains. Fortunately, material property management systems have kept pace with the growing user demands and evolved to versatile data management systems that can be customized to specific user needs. The more sophisticated of these provide facilities for: (i) data management functions such as access, version, and quality controls; (ii) a wide range of data import, export and analysis capabilities; (iii) data "pedigree" traceability mechanisms; (iv) data searching, reporting and viewing tools; and (v) access to the information via a wide range of interfaces. In this paper the important requirements for advanced material data management systems, future challenges and opportunities such as automated error checking, data quality characterization, identification of gaps in datasets, as well as functionalities and business models to fuel database growth and maintenance are discussed.

  8. Effective Materials Property Information Management for the 21st Century

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Weiju [ORNL; Cebon, David [Cambridge University; Barabash, Oleg M [ORNL

    2011-01-01

    This paper discusses key principles for the development of materials property information management software systems. There are growing needs for automated materials information management in various organizations. In part these are fuelled by the demands for higher efficiency in material testing, product design and engineering analysis. But equally important, organizations are being driven by the needs for consistency, quality and traceability of data, as well as control of access to proprietary or sensitive information. Further, the use of increasingly sophisticated nonlinear, anisotropic and multi-scale engineering analyses requires both processing of large volumes of test data for development of constitutive models and complex materials data input for Computer-Aided Engineering (CAE) software. And finally, the globalization of economy often generates great needs for sharing a single gold source of materials information between members of global engineering teams in extended supply-chains. Fortunately material property management systems have kept pace with the growing user demands and evolved to versatile data management systems that can be customized to specific user needs. The more sophisticated of these provide facilities for: (i) data management functions such as access, version, and quality controls; (ii) a wide range of data import, export and analysis capabilities; (iii) data pedigree traceability mechanisms; (iv) data searching, reporting and viewing tools; and (v) access to the information via a wide range of interfaces. In this paper the important requirements for advanced material data management systems, future challenges and opportunities such as automated error checking, data quality characterization, identification of gaps in datasets, as well as functionalities and business models to fuel database growth and maintenance are discussed.

  9. Atomistic Simulations of Material Properties under Extreme Conditions

    Science.gov (United States)

    An, Qi

    Extreme conditions involve low or high temperatures (> 1500 K), high pressures (> 30 MPa), high strains or strain rates, high radiation fluxes (> 100 dpa), and high electromagnetic fields (> 15T). Material properties under extreme conditions can be extremely different from those under normal conditions. Understanding material properties and performance under extreme conditions, including their dynamic evolution over time, plays an essential role in improving material properties and developing novel materials with desired properties. To understand material properties under extreme conditions, we use molecular dynamics (MD) simulations with recently developed reactive force fields (ReaxFF) and traditional embedded atom methods (EAM) potentials to examine various materials (e.g., energetic materials and binary liquids) and processes. The key results from the simulations are summarized below. Anisotropic sensitivity of RDX crystals: Based on the compress-and-shear reactive dynamics (CS-RD) simulations of cyclotrimethylene trinitramine (RDX) crystals, we predict that for mechanical shocks between 3 and 7 GPa, RDX is the most sensitive to shocks perpendicular to the (100) and (210) planes, while it is insensitive to those perpendicular to the (120), (111), and (110) planes. The simulations demonstrate that the molecular origin of anisotropic shock sensitivity is the steric hindrance to shearing of adjacent slip planes. Mechanisms of hotspot formation in polymer bonded explosives (PBXs): The simulations of a realistic model of PBXs reveal that hotspots may form at the nonplanar interfaces where shear relaxation leads to a dramatic temperature increase that persists long after the shock front has passed the interface. For energetic materials this temperature increase is coupled to chemical reactions that eventually lead to detonation. We show that decreasing the density of the binder eliminates the hotspots or reduces the sensitivity. Cavitation in binary metallic liquids

  10. Method and apparatus for modeling, visualization and analysis of materials

    KAUST Repository

    Aboulhassan, Amal

    2016-08-25

    A method, apparatus, and computer readable medium are provided for modeling of materials and visualization of properties of the materials. An example method includes receiving data describing a set of properties of a material, and computing, by a processor and based on the received data, geometric features of the material. The example method further includes extracting, by the processor, particle paths within the material based on the computed geometric features, and geometrically modeling, by the processor, the material using the geometric features and the extracted particle paths. The example method further includes generating, by the processor and based on the geometric modeling of the material, one or more visualizations regarding the material, and causing display, by a user interface, of the one or more visualizations.

  11. Computer-Aided Process Model For Carbon/Phenolic Materials

    Science.gov (United States)

    Letson, Mischell A.; Bunker, Robert C.

    1996-01-01

    Computer program implements thermochemical model of processing of carbon-fiber/phenolic-matrix composite materials into molded parts of various sizes and shapes. Directed toward improving fabrication of rocket-engine-nozzle parts, also used to optimize fabrication of other structural components, and material-property parameters changed to apply to other materials. Reduces costs by reducing amount of laboratory trial and error needed to optimize curing processes and to predict properties of cured parts.

  12. Transport properties of colossal magnetoresistive materials

    CERN Document Server

    Yates, K A

    2002-01-01

    A microwave technique was developed in order to test the validity of the hypothesis that the microwave transport of polycrystalline, optimally doped, colossal magnetoresistive materials was dominated by intragranular material. The microwave surface resistance at 9GHz was compared with dc resistivity and magnetisation to study the influence of yttrium doping on the grain boundary regions of bulk polycrystalline samples of La sub 0 sub . sub 7 sub - sub x Y sub x Ca sub 0 sub . sub 3 MnO sub 3. It was found that, within the grains, the addition of yttrium causes the activation energy above T sub p to increase. A phenomenological model was introduced to explain the data in terms of the difference in structure between the grain and grain boundary regions. The technique was also used to study the influence of deoxygenation on the grain boundary regions of bulk, polycrystalline, La sub 0 sub . sub 6 sub 7 Ca sub 0 sub . sub 3 sub 3 MnO sub 3. For samples interconnected porosity, low temperature (600 deg C), short a...

  13. Modeling electrical dispersion phenomena in Earth materials

    Directory of Open Access Journals (Sweden)

    D. Patella

    2008-06-01

    Full Text Available It is illustrated that IP phenomena in rocks can be described using conductivity dispersion models deduced as solutions to a 2nd-order linear differential equation describing the motion of a charged particle immersed in an external electrical field. Five dispersion laws are discussed, namely: the non-resonant positive IP model, which leads to the classical Debye-type dispersion law and by extension to the Cole-Cole model, largely used in current practice; the non-resonant negative IP model, which allows negative chargeability values, known in metals at high frequencies, to be explained as an intrinsic physical property of earth materials in specific field cases; the resonant flat, positive or negative IP models, which can explain the presence of peak effects at specific frequencies superimposed on flat, positive or negative dispersion spectra.

  14. Material properties of bovine intervertebral discs across strain rates.

    Science.gov (United States)

    Newell, Nicolas; Grigoriadis, Grigorios; Christou, Alexandros; Carpanen, Diagarajen; Masouros, Spyros D

    2017-01-01

    The intervertebral disc (IVD) is a complex structure responsible for distributing compressive loading to adjacent vertebrae and allowing the vertebral column to bend and twist. To study the mechanical behaviour of individual components of the IVD, it is common for specimens to be dissected away from their surrounding tissues for mechanical testing. However, disrupting the continuity of the IVD to obtain material properties of each component separately may result in erroneous values. In this study, an inverse finite element (FE) modelling optimisation algorithm has been used to obtain material properties of the IVD across strain rates, therefore bypassing the need to harvest individual samples of each component. Uniaxial compression was applied to ten fresh-frozen bovine intervertebral discs at strain rates of 10(-3)-1/s. The experimental data were fed into the inverse FE optimisation algorithm and each experiment was simulated using the subject specific FE model of the respective specimen. A sensitivity analysis revealed that the IVD's response was most dependent upon the Young's modulus (YM) of the fibre bundles and therefore this was chosen to be the parameter to optimise. Based on the obtained YM values for each test corresponding to a different strain rate (ε̇), the following relationship was derived:YM=35.5lnε̇+527.5. These properties can be used in finite element models of the IVD that aim to simulate spinal biomechanics across loading rates. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  15. Determination of thermal properties of composting bulking materials.

    Science.gov (United States)

    Ahn, H K; Sauer, T J; Richard, T L; Glanville, T D

    2009-09-01

    Thermal properties of compost bulking materials affect temperature and biodegradation during the composting process. Well determined thermal properties of compost feedstocks will therefore contribute to practical thermodynamic approaches. Thermal conductivity, thermal diffusivity, and volumetric heat capacity of 12 compost bulking materials were determined in this study. Thermal properties were determined at varying bulk densities (1, 1.3, 1.7, 2.5, and 5 times uncompacted bulk density), particle sizes (ground and bulk), and water contents (0, 20, 50, 80% of water holding capacity and saturated condition). For the water content at 80% of water holding capacity, saw dust, soil compost blend, beef manure, and turkey litter showed the highest thermal conductivity (K) and volumetric heat capacity (C) (K: 0.12-0.81 W/m degrees C and C: 1.36-4.08 MJ/m(3) degrees C). Silage showed medium values at the same water content (K: 0.09-0.47 W/m degrees C and C: 0.93-3.09 MJ/m(3) degrees C). Wheat straw, oat straw, soybean straw, cornstalks, alfalfa hay, and wood shavings produced the lowest K and C values (K: 0.03-0.30 W/m degrees C and C: 0.26-3.45 MJ/m(3) degrees C). Thermal conductivity and volumetric heat capacity showed a linear relationship with moisture content and bulk density, while thermal diffusivity showed a nonlinear relationship. Since the water, air, and solid materials have their own specific thermal property values, thermal properties of compost bulking materials vary with the rate of those three components by changing water content, bulk density, and particle size. The degree of saturation was used to represent the interaction between volumes of water, air, and solids under the various combinations of moisture content, bulk density, and particle size. The first order regression models developed in this paper represent the relationship between degree of saturation and volumetric heat capacity (r=0.95-0.99) and thermal conductivity (r=0.84-0.99) well. Improved

  16. Modeling of Laser Material Interactions

    Science.gov (United States)

    Garrison, Barbara

    2009-03-01

    Irradiation of a substrate by laser light initiates the complex chemical and physical process of ablation where large amounts of material are removed. Ablation has been successfully used in techniques such as nanolithography and LASIK surgery, however a fundamental understanding of the process is necessary in order to further optimize and develop applications. To accurately describe the ablation phenomenon, a model must take into account the multitude of events which occur when a laser irradiates a target including electronic excitation, bond cleavage, desorption of small molecules, ongoing chemical reactions, propagation of stress waves, and bulk ejection of material. A coarse grained molecular dynamics (MD) protocol with an embedded Monte Carlo (MC) scheme has been developed which effectively addresses each of these events during the simulation. Using the simulation technique, thermal and chemical excitation channels are separately studied with a model polymethyl methacrylate system. The effects of the irradiation parameters and reaction pathways on the process dynamics are investigated. The mechanism of ablation for thermal processes is governed by a critical number of bond breaks following the deposition of energy. For the case where an absorbed photon directly causes a bond scission, ablation occurs following the rapid chemical decomposition of material. The study provides insight into the influence of thermal and chemical processes in polymethyl methacrylate and facilitates greater understanding of the complex nature of polymer ablation.

  17. Computational modelling in materials at the University of the North

    CSIR Research Space (South Africa)

    Ngoepe, PE

    2005-09-01

    Full Text Available The authors review computational modelling studies in materials resulting from the National Research Foundation-Royal Society collaboration. Initially, investigations were confined to transport and defect properties in fluorine and oxygen ion...

  18. Validation of an efficient method of assigning material properties in finite element analysis of pelvic bone.

    Science.gov (United States)

    Shim, Vickie B; Battley, Mark; Anderson, Iain A; Munro, Jacob T

    2015-01-01

    Bone in the pelvis is a composite material with a complex anatomical structure that is difficult to model computationally. Rather than assigning material properties to increasingly smaller elements to capture detail in three-dimensional finite element (FE) models, properties can be assigned to Gauss points within larger elements. As part of a validation process, we compared experimental and analytical results from a composite beam under four-point load to FE models with material properties assigned to refined elements and Gauss points within larger elements. Both FE models accurately predicted deformation and the analytical predictions of internal shear stress.

  19. Characterization of ion-exchange membrane materials: properties vs structure.

    Science.gov (United States)

    Berezina, N P; Kononenko, N A; Dyomina, O A; Gnusin, N P

    2008-06-22

    This review focuses on the preparation, structure and applications of ion-exchange membranes formed from various materials and exhibiting various functions (electrodialytic, perfluorinated sulphocation-exchange and novel laboratory-tested membranes). A number of experimental techniques for measuring electrotransport properties as well as the general procedure for membrane testing are also described. The review emphasizes the relationships between membrane structures, physical and chemical properties and mechanisms of electrochemical processes that occur in charged membrane materials. The water content in membranes is considered to be a key factor in the ion and water transfer and in polarization processes in electromembrane systems. We suggest the theoretical approach, which makes it possible to model and characterize the electrochemical properties of heterogeneous membranes using several transport-structural parameters. These parameters are extracted from the experimental dependences of specific electroconductivity and diffusion permeability on concentration. The review covers the most significant experimental and theoretical research on ion-exchange membranes that have been carried out in the Membrane Materials Laboratory of the Kuban State University. These results have been discussed at the conferences "Membrane Electrochemistry", Krasnodar, Russia for many years and were published mainly in Russian scientific sources.

  20. Structure and properties of layered inorganic materials

    Institute of Scientific and Technical Information of China (English)

    Xue Duan

    2010-01-01

    @@ Inorganic layered materials are a class of advanced functional materials that have attracted considerable attention by virtue of their practical applications in a wide variety of fields. Sys-tematic studies of structure, design, synthesis, and fabrication processing may extend the range of practical utility of inor-ganic layered functional materials, in areas such as food industry,chemical industry, energy engineering, environmental engineer-ing, drug and gene delivery, electronics technology, and materials protection.

  1. Space-Time Transfinite Interpolation of Volumetric Material Properties.

    Science.gov (United States)

    Sanchez, Mathieu; Fryazinov, Oleg; Adzhiev, Valery; Comninos, Peter; Pasko, Alexander

    2015-02-01

    The paper presents a novel technique based on extension of a general mathematical method of transfinite interpolation to solve an actual problem in the context of a heterogeneous volume modelling area. It deals with time-dependent changes to the volumetric material properties (material density, colour, and others) as a transformation of the volumetric material distributions in space-time accompanying geometric shape transformations such as metamorphosis. The main idea is to represent the geometry of both objects by scalar fields with distance properties, to establish in a higher-dimensional space a time gap during which the geometric transformation takes place, and to use these scalar fields to apply the new space-time transfinite interpolation to volumetric material attributes within this time gap. The proposed solution is analytical in its nature, does not require heavy numerical computations and can be used in real-time applications. Applications of this technique also include texturing and displacement mapping of time-variant surfaces, and parametric design of volumetric microstructures.

  2. Saturation properties of a supercritical gas sorbed in nanoporous materials.

    Science.gov (United States)

    Poirier, Eric; Dailly, Anne

    2012-12-28

    The description of experimental gas adsorption data in terms of an accurate model is key to understand the adsorption mechanism and its limits. As a basic feature such a model should predict correctly the conditions under which saturation occurs. However, in the absence of bulk condensation properties for a supercritical adsorbate this matter remains open to discussions. In this study, the decreasing region of excess hydrogen adsorption isotherms measured down to 50 K is used to determine the adsorbed phase volume, density and pressure corresponding to saturation. The experimental method developed for these key measurements addresses the challenges of very low temperature adsorption measurements at high pressure. Therefore, the modifications specially made to a cryostat used in conjunction with a Sievert apparatus to reach high temperature stability (±10 mK) down to 40 K are presented. The approach is implemented on the novel nanoporous materials UMCM-1 and NOTT-112 over 50-77 K and 0-40 bar. The derived hydrogen saturation properties are found to be consistent with a Dubinin-Astakhov model. Importantly, the measured adsorbed hydrogen phase volume also compares well with the pore volume obtained from Ar porosimetry. The found saturation properties provide a physical basis to calculate consistent absolute adsorption isotherms and enthalpies, and to project the ultimate adsorption capacity of a conceptual material with a maximized specific surface area. The present findings provide additional evidence that the common view on supercritical adsorption, in which it is assumed that no liquid is formed and that the only possible mechanism involves monolayer coverage, does not hold in many nanoporous materials.

  3. Material properties of the heel fat pad across strain rates.

    Science.gov (United States)

    Grigoriadis, Grigoris; Newell, Nicolas; Carpanen, Diagarajen; Christou, Alexandros; Bull, Anthony M J; Masouros, Spyros D

    2017-01-01

    The complex structural and material behaviour of the human heel fat pad determines the transmission of plantar loading to the lower limb across a wide range of loading scenarios; from locomotion to injurious incidents. The aim of this study was to quantify the hyper-viscoelastic material properties of the human heel fat pad across strains and strain rates. An inverse finite element (FE) optimisation algorithm was developed and used, in conjunction with quasi-static and dynamic tests performed to five cadaveric heel specimens, to derive specimen-specific and mean hyper-viscoelastic material models able to predict accurately the response of the tissue at compressive loading of strain rates up to 150s(-1). The mean behaviour was expressed by the quasi-linear viscoelastic (QLV) material formulation, combining the Yeoh material model (C10=0.1MPa, C30=7MPa, K=2GPa) and Prony׳s terms (A1=0.06, A2=0.77, A3=0.02 for τ1=1ms, τ2=10ms, τ3=10s). These new data help to understand better the functional anatomy and pathophysiology of the foot and ankle, develop biomimetic materials for tissue reconstruction, design of shoe, insole, and foot and ankle orthoses, and improve the predictive ability of computational models of the foot and ankle used to simulate daily activities or predict injuries at high rate injurious incidents such as road traffic accidents and underbody blast. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  4. Measurement of Thermal Properties of Biosourced Building Materials

    Science.gov (United States)

    Pierre, Thomas; Colinart, Thibaut; Glouannec, Patrick

    2014-10-01

    This paper presents both experimental and theoretical works concerning the evaluation of the thermal conductivity and thermal diffusivity of hemp concrete. Experimental measurements of thermal properties are performed using a hot-strip technique for temperatures ranging from 3 to 30 and relative humidities ranging from 0 % to 95 %, thus creating a large database for this material. These experimental thermal conductivities are then compared with the results from the Krischer theoretical predictive model. The comparison shows good agreement, and a predictive analytical relation between the hemp concrete thermal conductivity, temperature, and relative humidity is determined.

  5. Recent Advances in the Sound Insulation Properties of Bio-based Materials

    Directory of Open Access Journals (Sweden)

    Xiaodong Zhu

    2013-12-01

    Full Text Available Many bio-based materials, which have lower environmental impact than traditional synthetic materials, show good sound absorbing and sound insulation performances. This review highlights progress in sound transmission properties of bio-based materials and provides a comprehensive account of various multiporous bio-based materials and multilayered structures used in sound absorption and insulation products. Furthermore, principal models of sound transmission are discussed in order to aid in an understanding of sound transmission properties of bio-based materials. In addition, the review presents discussions on the composite structure optimization and future research in using co-extruded wood plastic composite for sound insulation control. This review contributes to the body of knowledge on the sound transmission properties of bio-based materials, provides a better understanding of the models of some multiporous bio-based materials and multilayered structures, and contributes to the wider adoption of bio-based materials as sound absorbers.

  6. Cytocompatibility and Antibacterial Properties of Capping Materials

    Science.gov (United States)

    Arciola, Carla Renata; Monaco, Annachiara; Lombardini, Marco

    2014-01-01

    The aim of this study was to evaluate and compare the antimicrobial activity and cytocompatibility of six different pulp-capping materials: Dycal (Dentsply), Calcicur (Voco), Calcimol LC (Voco), TheraCal LC (Bisco), MTA Angelus (Angelus), and Biodentine (Septodont). To evaluate antimicrobial activity, materials were challenged in vitro with Streptococcus mutans, Streptococcus salivarius, and Streptococcus sanguis in the agar disc diffusion test. Cytocompatibility of the assayed materials towards rat MDPC-23 cells was evaluated at different times by both MTT and apoptosis assays. Results significantly differed among the different materials tested. Both bacterial growth inhibition halos and cytocompatibility performances were significantly different among materials with different composition. MTA-based products showed lower cytotoxicity and valuable antibacterial activity, different from calcium hydroxide-based materials, which exhibited not only higher antibacterial activity but also higher cytotoxicity. PMID:24959601

  7. Cytocompatibility and Antibacterial Properties of Capping Materials

    Directory of Open Access Journals (Sweden)

    Claudio Poggio

    2014-01-01

    Full Text Available The aim of this study was to evaluate and compare the antimicrobial activity and cytocompatibility of six different pulp-capping materials: Dycal (Dentsply, Calcicur (Voco, Calcimol LC (Voco, TheraCal LC (Bisco, MTA Angelus (Angelus, and Biodentine (Septodont. To evaluate antimicrobial activity, materials were challenged in vitro with Streptococcus mutans, Streptococcus salivarius, and Streptococcus sanguis in the agar disc diffusion test. Cytocompatibility of the assayed materials towards rat MDPC-23 cells was evaluated at different times by both MTT and apoptosis assays. Results significantly differed among the different materials tested. Both bacterial growth inhibition halos and cytocompatibility performances were significantly different among materials with different composition. MTA-based products showed lower cytotoxicity and valuable antibacterial activity, different from calcium hydroxide-based materials, which exhibited not only higher antibacterial activity but also higher cytotoxicity.

  8. Elucidating the role of interfacial materials properties in microfluidic packages.

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, Thayne L.

    2013-01-01

    The purpose of this work was to discover a method to investigate the properties of interfaces as described by a numerical physical model. The model used was adopted from literature and applied to a commercially available multiphysics software package. By doing this the internal properties of simple structures could be elucidated and then readily applied to more complex structures such as valves and pumps in laminate microfluidic structures. A numerical finite element multi-scale model of a cohesive interface comprised of heterogeneous material properties was used to elucidate irreversible damage from applied strain energy. An unknown internal state variable was applied to characterize the damage process. Using a constrained blister test, this unknown internal state variable could be determined for an adherend/adhesive/adherend body. This is particularly interesting for laminate systems with microfluidic and microstructures contained within the body. A laminate structure was designed and fabricated that could accommodate a variety of binary systems joined using nearly any technique such as adhesive, welding (solvent, laser, ultrasonic, RF, etc.), or thermal. The adhesive method was the most successful and easy to implement but also one of the more difficult to understand, especially over long periods of time. Welding methods are meant to achieve a bond that is similar to bulk properties and so are easier to predict. However, methods of welding often produce defects in the bonds.. Examples of the test structures used to elucidate the internal properties of the model were shown and demonstrated. The real life examples used this research to improve upon current designs and aided in creating complex structures for sensor and other applications.

  9. Metallurgy and properties of plasma spray formed materials

    Science.gov (United States)

    Mckechnie, T. N.; Liaw, Y. K.; Zimmerman, F. R.; Poorman, R. M.

    1992-01-01

    Understanding the fundamental metallurgy of vacuum plasma spray formed materials is the key to enhancing and developing full material properties. Investigations have shown that the microstructure of plasma sprayed materials must evolve from a powder splat morphology to a recrystallized grain structure to assure high strength and ductility. A fully, or near fully, dense material that exhibits a powder splat morphology will perform as a brittle material compared to a recrystallized grain structure for the same amount of porosity. Metallurgy and material properties of nickel, iron, and copper base alloys will be presented and correlated to microstructure.

  10. Absorption properties of waste matrix materials

    Energy Technology Data Exchange (ETDEWEB)

    Briggs, J.B. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

    1997-06-01

    This paper very briefly discusses the need for studies of the limiting critical concentration of radioactive waste matrix materials. Calculated limiting critical concentration values for some common waste materials are listed. However, for systems containing large quantities of waste materials, differences up to 10% in calculated k{sub eff} values are obtained by changing cross section data sets. Therefore, experimental results are needed to compare with calculation results for resolving these differences and establishing realistic biases.

  11. Cytocompatibility and Antibacterial Properties of Capping Materials

    OpenAIRE

    Claudio Poggio; Carla Renata Arciola; Riccardo Beltrami; Annachiara Monaco; Alberto Dagna; Marco Lombardini; Livia Visai

    2014-01-01

    The aim of this study was to evaluate and compare the antimicrobial activity and cytocompatibility of six different pulp-capping materials: Dycal (Dentsply), Calcicur (Voco), Calcimol LC (Voco), TheraCal LC (Bisco), MTA Angelus (Angelus), and Biodentine (Septodont). To evaluate antimicrobial activity, materials were challenged in vitro with Streptococcus mutans, Streptococcus salivarius, and Streptococcus sanguis in the agar disc diffusion test. Cytocompatibility of the assayed materials towa...

  12. Studies of molecular properties of polymeric materials

    Science.gov (United States)

    Harries, W. L.; Long, Sheila Ann T.; Long, Edward R., Jr.

    1990-01-01

    Aerospace environment effects (high energy electrons, thermal cycling, atomic oxygen, and aircraft fluids) on polymeric and composite materials considered for structural use in spacecraft and advanced aircraft are examined. These materials include Mylar, Ultem, and Kapton. In addition to providing information on the behavior of the materials, attempts are made to relate the measurements to the molecular processes occurring in the material. A summary and overview of the technical aspects are given along with a list of the papers that resulted from the studies. The actual papers are included in the appendices and a glossary of technical terms and definitions is included in the front matter.

  13. HYPERELASTIC MODELS FOR GRANULAR MATERIALS

    Energy Technology Data Exchange (ETDEWEB)

    Humrickhouse, Paul W; Corradini, Michael L

    2009-01-29

    A continuum framework for modeling of dust mobilization and transport, and the behavior of granular systems in general, has been reviewed, developed and evaluated for reactor design applications. The large quantities of micron-sized particles expected in the international fusion reactor design, ITER, will accumulate into piles and layers on surfaces, which are large relative to the individual particle size; thus, particle-particle, rather than particle-surface, interactions will determine the behavior of the material in bulk, and a continuum approach is necessary and justified in treating the phenomena of interest; e.g., particle resuspension and transport. The various constitutive relations that characterize these solid particle interactions in dense granular flows have been discussed previously, but prior to mobilization their behavior is not even fluid. Even in the absence of adhesive forces between particles, dust or sand piles can exist in static equilibrium under gravity and other forces, e.g., fluid shear. Their behavior is understood to be elastic, though not linear. The recent “granular elasticity” theory proposes a non-linear elastic model based on “Hertz contacts” between particles; the theory identifies the Coulomb yield condition as a requirement for thermodynamic stability, and has successfully reproduced experimental results for stress distributions in sand piles. The granular elasticity theory is developed and implemented in a stand- alone model and then implemented as part of a finite element model, ABAQUS, to determine the stress distributions in dust piles subjected to shear by a fluid flow. We identify yield with the onset of mobilization, and establish, for a given dust pile and flow geometry, the threshold pressure (force) conditions on the surface due to flow required to initiate it. While the granular elasticity theory applies strictly to cohesionless granular materials, attractive forces are clearly important in the interaction of

  14. Anisotropic Cloth Modeling for Material Fabric

    Science.gov (United States)

    Zhang, Mingmin; Pan, Zhigengx; Mi, Qingfeng

    Physically based cloth simulation has been challenging the graphics community for more than three decades. With the developing of virtual reality and clothing CAD, it has become the key technique of virtual garment and try-on system. Although it has received considerable attention in computer graphics, due to its flexible property and realistic feeling that the textile engineers pay much attention to, there is not a successful methodology to simulate cloth both in visual realism and physical accuracy. We present a new anisotropic textile modeling method based on physical mass-spring system, which models the warps and wefts separately according to the different material fabrics. The simulation process includes two main steps: firstly the rigid object simulation and secondly the flexible mass simulation near to be equilibrium. A multiresolution modeling is applied to enhance the tradeoff fruit of the realistic presentation and computation cost. Finally, some examples and the analysis results show the efficiency of the proposed method.

  15. Material properties of one-dimensional systems studied by path-integral quantum Monte Carlo simulations and an analytical many-body model

    Science.gov (United States)

    Böhm, Michael C.; Schulte, Joachim; Utrera, Luis

    Feynman path-integral quantum Monte Carlo (QMC) simulations and an analytic many-body approach are used to study the ground state properties of one-dimensional (1D) chains in the theoretical framework of model Hamiltonians of the Hubbard type. The QMC algorithm is employed to derive position-space quantities, while band structure properties are evaluated by combining QMC data with expressions derived in momentum (k) space. Bridging link between both representations is the quasi-chemical approximation (QCA). Electronic charge fluctuations and the fluctuations of the magnetic local moments are studied as a function of the on-site density and correlation strength, which is given by the ratio between two-electron interaction and kinetic hopping. Caused by the non-analytic behaviour of the chemical potential μ = ∂E/∂ (with E denoting the electronic energy), strict 1D systems with an on-site density of 1·0 do not exhibit the properties of a conductor for any non-zero interaction beyond the mean-field approximation. The QMC simulations lead to straightforward access to the probabilities Pi(n) of finding n = 0, 1, 2 electrons at the ith lattice site. The Pi(n) elements allow to calculate the enhancement factors on the electron spin susceptibility χ, effective electronic mass m* and Knight shift κ. m* is enhanced by a bandwidth renormalization factor D-10, κ by an element ηK mapping the additional localization of the correlated electrons in the presence of an external magnetic field B and χ by the product D-10 ηK. Available experimental data are discussed in the light of the present theoretical findings.

  16. Transition metal chalcogenides: ultrathin inorganic materials with tunable electronic properties.

    Science.gov (United States)

    Heine, Thomas

    2015-01-20

    presence of an external electric field are reported. While all materials of the MoWSeS family share the same qualitative properties, their individual values can differ strongly, for example, the spin-orbit splitting in WSe2 reaches the value of 428 meV, nearly three times that of MoS2. Further, we discuss the effect of strain on the electronic properties (straintronics). While MoWSeS single layers are very robust against external electric fields, bilayers show a linear reduction of the band gap, even reaching a semiconductor-metal phase transition, and an increase of the spin-orbit splitting from zero to the monolayer value at rather small fields. Strain is yet another possibility to control the band gap in a linear way, and MoWSeS monolayers become metallic at strain values of ∼10%. The density-functional based tight-binding model is a useful tool to investigate the electronic and structural properties, including electron conductance, of large MoS2 structures, which show spontaneous rippling in finite-temperature molecular dynamics simulations. Structural defects in MoS2 result in anisotropy of the electric conductivity. Finally, DFT predictions on the properties of noble metal dichalcogenides are presented. Most strikingly, 1T PdS2 is an indirect band gap semiconductor in its monolayer form but becomes metallic as a bilayer.

  17. New elastoplastic materials with performance properties

    OpenAIRE

    Sanda VISAN,; Virginia CIOBOTARU; Florica IONESCU; Anca ANGELESCU

    2009-01-01

    The fabrication of high performance materials using EPDM rubber and polyethylene mixtures with a low cost, nonpolluting and minimum investment technology is studied. These new materials can be used for obtaining a lot of goods for the economy, sport and private life..

  18. New elastoplastic materials with performance properties

    Directory of Open Access Journals (Sweden)

    Sanda VISAN,

    2009-06-01

    Full Text Available The fabrication of high performance materials using EPDM rubber and polyethylene mixtures with a low cost, nonpolluting and minimum investment technology is studied. These new materials can be used for obtaining a lot of goods for the economy, sport and private life.

  19. Benchmarking Density Functional Theory Based Methods To Model NiOOH Material Properties: Hubbard and van der Waals Corrections vs Hybrid Functionals.

    Science.gov (United States)

    Zaffran, Jeremie; Caspary Toroker, Maytal

    2016-08-09

    NiOOH has recently been used to catalyze water oxidation by way of electrochemical water splitting. Few experimental data are available to rationalize the successful catalytic capability of NiOOH. Thus, theory has a distinctive role for studying its properties. However, the unique layered structure of NiOOH is associated with the presence of essential dispersion forces within the lattice. Hence, the choice of an appropriate exchange-correlation functional within Density Functional Theory (DFT) is not straightforward. In this work, we will show that standard DFT is sufficient to evaluate the geometry, but DFT+U and hybrid functionals are required to calculate the oxidation states. Notably, the benefit of DFT with van der Waals correction is marginal. Furthermore, only hybrid functionals succeed in opening a bandgap, and such methods are necessary to study NiOOH electronic structure. In this work, we expect to give guidelines to theoreticians dealing with this material and to present a rational approach in the choice of the DFT method of calculation.

  20. Three-dimensional modeling of piezoelectric materials.

    Science.gov (United States)

    Brissaud, Michel

    2010-09-01

    This paper deals with 3-D modeling of piezoelectric materials. The model is based on an exact description of the potential and electric field inside a material. Moreover, coherent piezoelectric equations are used. Modeling has been applied to rectangular and cylindrical elements. In each case, the exact equations of the displacements along the three coordinate axes and the corresponding electric impedance are calculated. The general resonance conditions are stated for these two geometries. It is shown that, contrary to the 1-D models, a unique equation describes lateral and thickness vibrations, or radial and thickness vibrations. These properties enable us to analytically calculate the frequency spectrum of rectangular elements, thick disks, or cylinders and also thick rings or hollow cylinders versus the width to thickness ratio. It is then very easy to determine the corresponding dispersion diagram related to each geometry sample. These resonance conditions are similar to those deduced from the 1-D model described in the IEEE standard but are more general and necessitate no cancelling out assumptions. In addition, contrary to 1-D models, the wave velocities and the permittivity are independent of the element geometry (parallelepiped or cylindrical). The wave velocities are equal to those stated for the wave propagation in infinite medium and measured with pulse-echo techniques. It is the coupling inside the material which modifies the resonance conditions and not the geometrical dimensions of the vibrating element. 3-D modeling and 1-D radial mode of the admittance of a thick disk are calculated and compared with experimental measurements. Theoretical and measured admittances are compared and discussed.

  1. Compact rock material gas permeability properties

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Huanling, E-mail: whl_hm@163.com [Key Laboratory of Coastal Disaster and Defence, Ministry of Education, Hohai University, Nanjing 210098 (China); LML, University of Lille, Cite Scientifique, 59655 Villeneuve d’Ascq (France); Xu, Weiya; Zuo, Jing [Institutes of Geotechnical Engineering, Hohai University, Nanjing 210098 (China)

    2014-09-15

    Natural compact rocks, such as sandstone, granite, and rock salt, are the main materials and geological environment for storing underground oil, gas, CO{sub 2,} shale gas, and radioactive waste because they have extremely low permeabilities and high mechanical strengths. Using the inert gas argon as the fluid medium, the stress-dependent permeability and porosity of monzonitic granite and granite gneiss from an underground oil storage depot were measured using a permeability and porosity measurement system. Based on the test results, models for describing the relationships among the permeability, porosity, and confining pressure of rock specimens were analyzed and are discussed. A power law is suggested to describe the relationship between the stress-dependent porosity and permeability; for the monzonitic granite and granite gneiss (for monzonitic granite (A-2), the initial porosity is approximately 4.05%, and the permeability is approximately 10{sup −19} m{sup 2}; for the granite gneiss (B-2), the initial porosity is approximately 7.09%, the permeability is approximately 10{sup −17} m{sup 2}; and the porosity-sensitivity exponents that link porosity and permeability are 0.98 and 3.11, respectively). Compared with moderate-porosity and high-porosity rocks, for which φ > 15%, low-porosity rock permeability has a relatively lower sensitivity to stress, but the porosity is more sensitive to stress, and different types of rocks show similar trends. From the test results, it can be inferred that the test rock specimens’ permeability evolution is related to the relative particle movements and microcrack closure.

  2. RANDOM MICROSTRUCTURE FINITE ELEMENT METHOD AND ITS VERIFICATION FOR EFFECTIVE PROPERTIES OF COMPOSITE MATERIALS

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The present study aims at developing a new method-Random M icrostructure Finite Element Method (RMFEM)for the effective properties of composite materials . In this method, a random microstructure model is used to simulate the microstructure of the real composite materials. The physical fields in such a randm microstructure model under specified boundary and initial conditions are analyzed by finite element method. The effective properties of composite materials can be obtained from the analysis results. As verification, some effective properties of composite materials, such as elastic module,thermal expansion coefficient, thermal conductivity and elastoplastic properties, are investigated by random microstructure finite element method. The numerical results are given together with the experimental data. It i- revealed that the random microstructure finite element method is a very valid method for the determination of the effective properties of composite materials.

  3. Transport properties of damaged materials. Cementitious barriers partnership

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2014-11-01

    The objective of the Cementitious Barriers Partnership (CBP) project is to develop tools to improve understanding and prediction of the long-term structural, hydraulic, and chemical performance of cementitious barriers used in low-level waste storage applications. One key concern for the long-term durability of concrete is the degradation of the cementitious matrix, which occurs as a result of aggressive chemical species entering the material or leaching out in the environment, depending on the exposure conditions. The objective of the experimental study described in this report is to provide experimental data relating damage in cementitious materials to changes in transport properties, which can eventually be used to support predictive model development. In order to get results within a reasonable timeframe and to induce as much as possible uniform damage level in materials, concrete samples were exposed to freezing and thawing (F/T) cycles. The methodology consisted in exposing samples to F/T cycles and monitoring damage level with ultrasonic pulse velocity measurements. Upon reaching pre-selected damage levels, samples were tested to evaluate changes in transport properties. Material selection for the study was motivated by the need to get results rapidly, in order to assess the relevance of the methodology. Consequently, samples already available at SIMCO from past studies were used. They consisted in three different concrete mixtures cured for five years in wet conditions. The mixtures had water-to-cement ratios of 0.5, 0.65 and 0.75 and were prepared with ASTM Type I cement only. The results showed that porosity is not a good indicator for damage caused by the formation of microcracks. Some materials exhibited little variations in porosity even for high damage levels. On the other hand, significant variations in tortuosity were measured in all materials. This implies that damage caused by internal pressure does not necessarily create additional pore space in

  4. Cementitious barriers partnership transport properties of damaged materials

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2014-11-01

    The objective of the Cementitious Barriers Partnership (CBP) project is to develop tools to improve understanding and prediction of the long-term structural, hydraulic, and chemical performance of cementitious barriers used in low level waste storage applications. One key concern for the long-term durability of concrete is the degradation of the cementitious matrix, which occurs as a result of aggressive chemical species entering the material or leaching out in the environment, depending on the exposure conditions. The objective of the experimental study described in this report is to provide experimental data relating damage in cementitious materials to changes in transport properties, which can eventually be used to support predictive model development. In order to get results within a reasonable timeframe and to induce as much as possible uniform damage level in materials, concrete samples were exposed to freezing and thawing (F/T) cycles. The methodology consisted in exposing samples to F/T cycles and monitoring damage level with ultrasonic pulse velocity measurements. Upon reaching pre-selected damage levels, samples were tested to evaluate changes in transport properties. Material selection for the study was motivated by the need to get results rapidly, in order to assess the relevance of the methodology. Consequently, samples already available at SIMCO from past studies were used. They consisted in three different concrete mixtures cured for five years in wet conditions. The mixtures had water-to-cement ratios of 0.5, 0.65 and 0.75 and were prepared with ASTM Type I cement only. The results showed that porosity is not a good indicator for damage caused by the formation of microcracks. Some materials exhibited little variations in porosity even for high damage levels. On the other hand, significant variations in tortuosity were measured in all materials. This implies that damage caused by internal pressure do not necessarily creates additional pore space in

  5. Textile materials for lightweight constructions technologies, methods, materials, properties

    CERN Document Server

    2016-01-01

    In this book, experts on textile technologies convey both general and specific informa­tion on various aspects of textile engineering, ready-made technologies, and textile chemistry. They describe the entire process chain from fiber materials to various yarn constructions, 2D and 3D textile constructions, preforms, and interface layer design. In addition, the authors introduce testing methods, shaping and simulation techniques for the characterization of and structural mechanics calculations on anisotropic, pliable high-performance textiles, including specific examples from the fields of fiber plastic composites, textile concrete, and textile membranes. Readers will also be familiarized with the potential offered by increasingly popular textile structures, for instance in the fields of composite technology, construction technology, security technology, and membrane technology. Textile materials and semi-finished products have widely varied potential characteristics, and are commonly used as essential element...

  6. Elastic properties of superconductors and materials with weakly correlated spins.

    Science.gov (United States)

    Binek, Christian

    2017-07-07

    It is shown that in the ergodic regime, the temperature dependence of Young's modulus is solely determined by the magnetic properties of a material. For the large class of materials with paramagnetic or diamagnetic response, simple functional forms of the temperature derivative of Young's modulus are derived and compared with experimental data and empirical results. Superconducting materials in the Meissner phase are ideal diamagnets. As such, they display remarkable elastic properties. Constant diamagnetic susceptibility gives rise to a temperature independent elastic modulus for ceramic and single crystalline superconductors alike. The thermodynamic approach established in this report, paves the way to tailor elastic material parameters through the design of magnetic properties.

  7. Micro-Scale Experiments and Models for Composite Materials with Materials Research

    DEFF Research Database (Denmark)

    Zike, Sanita

    Numerical models are frequently implemented to study micro-mechanical processes in polymer/fibre composites. To ensure that these models are accurate, the length scale dependent properties of the fibre and polymer matrix have to be taken into account. Most often this is not the case, and material...... properties acquired at macro-scale are used for micro-mechanical models. This is because material properties at the macro-scale are much more available and the test procedures to obtain them are well defined. The aim of this research was to find methods to extract the micro-mechanical properties of the epoxy...... resin used in polymer/fibre composites for wind turbine blades combining experimental, numerical, and analytical approaches. Experimentally, in order to mimic the stress state created by a void in a bulk material, test samples with finite root radii were made and subjected to a double cantilever beam...

  8. Superconductivity and magnetism: Materials properties and developments

    Energy Technology Data Exchange (ETDEWEB)

    Andersen, N.H.; Bay, N.; Grivel, J.C. (eds.) [and others

    2003-07-01

    The 24th Risoe International Symposium on Materials Science focuses on development of new materials, devices and applications, as well as experimental and theoretical studies of novel and unexplained phenomena in superconductivity and magnetism, e.g. within high.T{sub c} superconductivity, magnetic superconductors, MgB{sub 2}, CMR materials, nanomagnetism and spin-tronics. The aim is to stimulate exchange of ideas and establish new collaborations between leading Danish and international scientists. The topics are addressed by presentations from 24 invited speakers and by 41 contributed papers. (ln)

  9. Fundamental Material Properties Underlying Solid Oxide Electrochemistry

    DEFF Research Database (Denmark)

    Mogensen, Mogens Bjerg; Hansen, Karin Vels; Holtappels, Peter

    2012-01-01

    and electronic conductor (MIEC) the electrode is. Selected examples of literature studies of specific electrodes in solid oxide cells (SOC) are discussed. The reported effects of impurities - both impurities in the electrode materials and in the gases – point to high reactivity and mobility of materials...... in the TPB region. Also, segregations to the surfaces and interfaces of the electrode materials, which may affect the electrode reaction mechanism, are very dependent on the exact history of fabrication and operation. The positive effects of even small concentrations of nanoparticles in the electrodes may...

  10. Fundamental Material Properties Underlying Solid Oxide Electrochemistry

    DEFF Research Database (Denmark)

    Mogensen, Mogens Bjerg; Hansen, Karin Vels; Holtappels, Peter

    2012-01-01

    and electronic conductor (MIEC) the electrode is. Selected examples of literature studies of specific electrodes in solid oxide cells (SOC) are discussed. The reported effects of impurities - both impurities in the electrode materials and in the gases – point to high reactivity and mobility of materials...... place. The length of the TPB is a key factor even though the width and depth of the zone, in which the rate limiting reactions take place, may vary depending of the degree of the electrode materials ability to conduct both electrons and ions, i.e. the TPB zone volume depends on how good a mixed ionic...... in the TPB region. Also, segregations to the surfaces and interfaces of the electrode materials, which may affect the electrode reaction mechanism, are very dependent on the exact history of fabrication and operation. The positive effects of even small concentrations of nanoparticles in the electrodes may...

  11. Optical properties of active photonic materials

    OpenAIRE

    Zeng, Yong

    2007-01-01

    Because of the generation of polaritons, which are quasiparticles possessing the characteristics of both photonics and electronics, active photonic materials offer a possible solution to transfer electromagnetic energy below the diffraction limit and further increase the density of photonic integrated circuits. A theoretical investigation of these exciting materials is, therefore, very important for practical applications. Four different kinds of polaritons have been studied in this thesis, (...

  12. Elastic properties of superconductors and materials with weakly correlated spins

    OpenAIRE

    Binek, Christian

    2017-01-01

    It is shown that in the ergodic regime, the temperature dependence of Young?s modulus is solely determined by the magnetic properties of a material. For the large class of materials with paramagnetic or diamagnetic response, simple functional forms of the temperature derivative of Young?s modulus are derived and compared with experimental data and empirical results. Superconducting materials in the Meissner phase are ideal diamagnets. As such, they display remarkable elastic properties. Const...

  13. Towards the Application of Structure-Property Relationship Modeling in Materials Science: Predicting the Seebeck Coefficient for Ionic Liquid/Redox Couple Systems.

    Science.gov (United States)

    Sosnowska, Anita; Barycki, Maciej; Gajewicz, Agnieszka; Bobrowski, Maciej; Freza, Sylwia; Skurski, Piotr; Uhl, Stefanie; Laux, Edith; Journot, Tony; Jeandupeux, Laure; Keppner, Herbert; Puzyn, Tomasz

    2016-06-01

    This work focuses on determining the influence of both ionic-liquid (IL) type and redox couple concentration on Seebeck coefficient values of such a system. The quantitative structure-property relationship (QSPR) and read-across techniques are proposed as methods to identify structural features of ILs (mixed with LiI/I2 redox couple), which have the most influence on the Seebeck coefficient (Se ) values of the system. ILs consisting of small, symmetric cations and anions with high values of vertical electron binding energy are recognized as those with the highest values of Se . In addition, the QSPR model enables the values of Se to be predicted for each IL that belongs to the applicability domain of the model. The influence of the redox-couple concentration on values of Se is also quantitatively described. Thus, it is possible to calculate how the value of Se will change with changing redox-couple concentration. The presence of the LiI/I2 redox couple in lower concentrations increases the values of Se , as expected.

  14. Extended propagation model for interfacial crack in composite material structure

    Institute of Scientific and Technical Information of China (English)

    闫相桥; 冯希金

    2002-01-01

    An interfacial crack is a common damage in a composite material structure . An extended propaga-tion model has been established for an interfacial crack to study the dependence of crack growth on the relativesizes of energy release rates at left and right crack tips and the properties of interfacial material characterize thegrowth of interfacial crack better.

  15. Dielectric properties of materials at microwave frequencies

    Directory of Open Access Journals (Sweden)

    Ivo Křivánek

    2008-01-01

    Full Text Available The paper introduces the review of the present state of art in the measurement of the interaction of electromagnetic waves with different kinds of materials. It is analysis of the possibilities of the mea­surement of the interaction of high frequencies waves (microwaves with materials and proposal of the experimental method for the studies mentioned above.The electromagnetic field consists of two components: electric and magnetic field. The influence of these components on materials is different. The influence of the magnetic field is negligible and it has no impact on practical use. The influence of the electric field is strong as the interaction between them results in the creation of electric currents in the material (Křivánek and Buchar, 1993.Experiments focused on the evaluation of the complex dielectric permitivity of different materials have been performed. The permitivity of solid material is also measurable by phasemethod, when the specimen is a part of transmission sub-circuit. Microwave instrument for complex permittivity measurement works in X frequency band (8.2–12.5 GHz, the frequency 10.1 GHz was used for all the measurement in the laboratory of physics, Mendel University in Brno. The extensive number of experimental data have been obtained for different materials. The length of the square side of the ae­rial open end was 50 mm and internal dimensions of waveguides were 23 mm × 10 mm. The samples have form of the plate shape with dimensions 150 mm × 150 mm × 4 mm.

  16. Test Methods for Measuring Material Properties of Composite Materials in all Three Material Axes

    Science.gov (United States)

    2012-01-24

    conducted using ASTM D 6641/D 6641M “Standard Test Method for Determining the Compressive Properties of Polymer Matrix Composite Laminates Using a Combined...D 7291/D 7291M “Standard Test Method for Through-Thickness “Flatwise” Tensile Strength and Elastic Modulus of a Fiber- Reinforced Polymer Matrix Composite Material...34Flatwise" Tensile Strength and Elastic Modulus of a Fiber-Reinforced Polymer Matrix Composite Material”. West Conshohocken, PA, 2005, DOI: 10.1520/D7291

  17. Modeling skull electrical properties

    OpenAIRE

    Sadleir, R. J.; A Argibay

    2007-01-01

    Accurate representations and measurements of skull electrical conductivity are essential in developing appropriate forward models for applications such as inverse EEG or Electrical Impedance Tomography of the head. Because of its layered structure, it is often assumed that skull is anisotropic, with an anisotropy ratio around 10. However, no detailed investigation of skull anisotropy has been performed. In this paper we investigate four-electrode measurements of conductivities and their relat...

  18. Transport properties site descriptive model. Guidelines for evaluation and modelling

    Energy Technology Data Exchange (ETDEWEB)

    Berglund, Sten [WSP Environmental, Stockholm (Sweden); Selroos, Jan-Olof [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

    2004-04-01

    modelling of transport properties, and hence the guidelines in this report, involve two main categories of parameters: Parameters that characterise the retention properties of geologic materials. These parameters quantify the diffusion and sorption properties of intact and altered rock, fracture coatings and fracture-filling materials, and are described within the framework of the 3D geometric models devised by Geology. Parameters that characterise solute transport along flow paths (flow-related transport parameters). These parameters include the 'F-parameter' and 'water travel time', tw, and parameters that account for spatial variability in diffusion and sorption. The flow-related parameters are obtained by means of particle tracking simulations in groundwater flow models.

  19. Material Property Correlations: Comparisons between FRAPCON-3.4, FRAPTRAN 1.4, and MATPRO

    Energy Technology Data Exchange (ETDEWEB)

    Luscher, Walter G.; Geelhood, Kenneth J.

    2010-08-01

    The U.S. Nuclear Regulatory Commission (NRC) uses the computer codes FRAPCON-3 and FRAPTRAN to model steady state and transient fuel behavior, respectively, in regulatory analysis. In order to effectively model fuel behavior, material property correlations must be used for a wide range of operating conditions (e.g. temperature and burnup). In this sense, a 'material property' is a physical characteristic of the material whose quantitative value is necessary in the analysis process. Further, the property may be used to compare the benefits of one material versus another. Generally speaking, the material properties of interest in regulatory analysis of nuclear fuel behavior are mechanical or thermodynamic in nature. The issue of what is and is not a 'material property' will never be universally resolved. In this report, properties such as thermal conductivity are included. Other characteristics of the material (e.g. fission gas release) are considered 'models' rather than properties, and are discussed elsewhere. Still others (e.g., neutron absorption cross-section) are simply not required in this specific analysis. The material property correlations for the FRAPCON-3 and FRAPTRAN computer codes were documented in NUREG/CR-6534 and NUREG/CR-6739, respectively. Some of these have been modified or updated since the original code documentation was published. The primary purpose of this report is to consolidate the current material property correlations used in FRAPCON-3 and FRAPTRAN into a single document. Material property correlations for oxide fuels, including uranium dioxide (UO2) and mixed oxide (MOX) fuels, are described in Section 2. Throughout this document, the term MOX will be used to describe fuels that are blends of uranium and plutonium oxides, (U,Pu)O2. The properties for uranium dioxide with other additives (e.g., gadolinia) are also discussed. Material property correlations for cladding materials and gases are described in

  20. Tribological Property of Polyimide Porous Materials

    Institute of Scientific and Technical Information of China (English)

    PU Yu-ping; L(U) Guang-shu; LI Xiao-jun; XIAO Han-cheng

    2006-01-01

    The friction performance of the polyimide (PI) porous composite materials made by moulding method with MoS2 or polytetrafluoroethylene (PTFE) appended are disserted. The result shows that all the PI-based porous composites have the performance of transfer lubrication in the friction process, and the transfer film is built between the counter friction bodies; with the increasing of the MoS2 a mount from 0 to 20%, the friction coefficient trends toward decrease, and the tr ansfer lubricate phenomenon become more obvious; when adding PTFE as synergist t o the porous PI+MoS2 composite material, the synergistic effect happens, which can improve the friction performance of the material effectively.

  1. Structure and Properties of Energetic Materials

    Science.gov (United States)

    1992-12-02

    7.76 9.11 30 Gurney energy (MJ/kg) 1.1 1.6 30 Heat of detonation (MJ/kg) -5.02 -6.78 30 In Table 2 we compare the properties of TATB and...velocity of HMX is some 17% greater than that of TATB, the Gurney energy 45% greater, and the heat of detonation 35% greater One reason that TATB...MJ/kg) 1.1 1.6 30 Heat of detonation (MJ/kg) -5.02 -6.78 30 In Table 2 we compare the properties of TATB and cyclotetramethylenetetranitramine (HMX

  2. Adsorption Properties of Chalk Reservoir Materials

    DEFF Research Database (Denmark)

    Okhrimenko, Denis

    Understanding adsorption energetics and wetting properties of calcium carbonate surfaces is essential for developing remediation strategies for aquifers, improving oil recovery, minimising risk in CO2 storage and optimising industrial processes. This PhD was focussed on comparing the vapour....../gas adsorption properties of synthetic calcium carbonate phases (calcite, vaterite and aragonite) with chalk, which is composed of biogenic calcite (>98%). In combination with data from nanotechniques, the results demonstrate the complexity of chalk behavior and the role of nanoscale clay particles. The results...

  3. Ceramic materials testing and modeling

    Energy Technology Data Exchange (ETDEWEB)

    Wilfinger, K. R., LLNL

    1998-04-30

    Certain refractory ceramics (notably oxides) have desirable properties suitable for the construction of ceramic waste containers for long term use in nuclear waste disposal applications. In particular, they are far less prone to environmental corrosion than metals under realistic repository conditions. The aqueous corrosion rates of oxides such as magnesium aluminate spinel (MgAl{sub 2}0{sub 4}) and alumina (Al{sub 2}0{sub 4}) fall in the range of a few millimeters per million years. Oxide ceramics are also not likely to be subject to microbiologically influenced corrosion, which apparently can attack most, if not all, of the available engineering metals. Ceramics have a reputation for poor mechanical performance and large, impermeable objects are not easily fabricated by most current fabrication methods. As a result, the most promising approach for incorporating ceramics in large waste packages appears to be to apply a high density ceramic coating to a supporting metallic structure. Ceramic coatings 2048 applied by a thermal spray technique can be made effectively seamless and provide a method for final closure of the waste package while maintaining low average temperatures for the entire assembly. The corrosion resistance of the ceramic should prevent or delay water penetration to the underlying metal, which will in turn provide most of the mechanical strength and toughness required by the application. In this way, the major concerns regarding the ceramic coating become ensuring it is impervious to moisture, its adherence and its resistance to mechanical stresses during handling or resulting from rock fall in the repository. Without water, electrochemical corrosion and microbiologically influenced corrosion processes are considered impossible, so a complete coating should protect the metal vessels for far longer than the current design requirements. Even an imperfect coating should extend the life of the package, delaying the onset and reducing the severity of

  4. Organic materials with nonlinear optical properties

    Science.gov (United States)

    Stupp, Samuel I.; Son, Sehwan; Lin, Hong-Cheu

    1995-01-01

    The present invention is directed to organic materials that have the ability to double or triple the frequency of light that is directed through the materials. Particularly, the present invention is directed to the compound 4-[4-(2R)-2-cyano-7-(4'-pentyloxy-4-biphenylcarbonyloxy)phenylheptylidene) phenylcarbonyloxy]benzaldehyde, which can double the frequency of light that is directed through the compound. The invention is also directed to the compound (12-hydroxy-5,7-dodecadiynyl) 4'-[(4'-pentyloxy-4-biphenyl)carbonyloxy]-4-biphenylcarboxylate, and its polymeric form. The polymeric form can triple the frequency of light directed through it.

  5. The effects of variability in bank material properties on riverbank stability: Goodwin Creek, Mississippi

    Science.gov (United States)

    Parker, Chris; Simon, Andrew; Thorne, Colin R.

    2008-11-01

    Bank retreat is an important area of research within fluvial geomorphology and is a land management problem of global significance. The Yazoo River Basin in Mississippi is one example of a system which is experiencing excessive erosion and bank instability. The properties of bank materials are important in controlling the stability of stream banks and past studies have found that these properties are often variable spatially. Through an investigation of bank material properties on a stretch of Goodwin Creek in the Yazoo Basin, Mississippi, this study focuses on: i) how and why effective bank material properties vary through different scales; ii) how this variation impacts on the outputs from a bank stability model; and iii) how best to appropriately represent this variability within a bank stability model. The study demonstrates the importance that the variability of effective bank material properties has on bank stability: at both the micro-scale within a site, and at the meso-scale between sites in a reach. This variability was shown to have important implications for the usage of the Bank Stability and Toe Erosion Model (BSTEM), a deterministic bank stability model that currently uses a single value to describe each bank material property. As a result, a probabilistic representation of effective bank material strength parameters is recommended as a potential solution for any bank stability model that wishes to account for the important influence of the inherent variability of soil properties.

  6. Handbook of the Properties of Optical Materials

    Science.gov (United States)

    1984-01-01

    EFFECTIVE MASS - - MOBILITY - - A-2 ARSEWIC SELENIOE (As2 Se3 ) OPTICAL PROPERTIES TRANSMISSION RANGE: 9 - 11n Optical Absorption Coefficient = 0.079...of 55 KRS-5 as a function of wavelength. A-2120 ZINC SELENIOE ZnSe 0 STRUCTURE CRYSTALLINE SYMMETRY = Cubic, 43m LATTICE CONSTANTS (A) = a = 5.667

  7. Adsorption Properties of Chalk Reservoir Materials

    DEFF Research Database (Denmark)

    Okhrimenko, Denis

    Understanding adsorption energetics and wetting properties of calcium carbonate surfaces is essential for developing remediation strategies for aquifers, improving oil recovery, minimising risk in CO2 storage and optimising industrial processes. This PhD was focussed on comparing the vapour...

  8. Dynamic Deformation Properties of Energetic Composite Materials

    Science.gov (United States)

    2005-04-01

    properties are close to that of pure beryllium ( Silversmith and Averbach 1970), but as far as we know no-one has acted on this suggestion. According to...J.L. (1998) "Analysis of load oscillations in instrumented impact testing" Engng Fract. Mech. 60 437-446 Silversmith , D.J. and Averbach, B.L. (1970

  9. Material properties under intensive dynamic loading

    CERN Document Server

    Cherne, Frank J; Zhernokletov, Mikhail V; Glushak, B L; Zocher, Marvin A

    2007-01-01

    Understanding the physical and thermomechanical response of materials subjected to intensive dynamic loading is a challenge of great significance in engineering today. This volume assumes the task of gathering both experimental and diagnostic methods in one place, since not much information has been previously disseminated in the scientific literature.

  10. Modification of Textile Materials' Surface Properties Using Chemical Softener

    Directory of Open Access Journals (Sweden)

    Jurgita KOŽENIAUSKIENĖ

    2011-03-01

    Full Text Available In the present study the effect of technological treatment involving the processes of washing or washing and softening with chemical cationic softener "Surcase" produced in Great Britain on the surface properties of cellulosic textile materials manufactured from cotton, bamboo and viscose spun yarns was investigated. The changes in textile materials surface properties were evaluated using KTU-Griff-Tester device and FEI Quanta 200 FEG scanning electron microscope (SEM. It was observed that the worst hand properties and the higher surface roughness are observed of cotton materials if compared with those of bamboo and viscose materials. Also, it was shown that depending on the material structure the handle parameters of knitted materials are the better than the ones of woven fabrics.http://dx.doi.org/10.5755/j01.ms.17.1.249

  11. Acoustic Properties of Innovative Material from Date Palm Fibre

    Directory of Open Access Journals (Sweden)

    Lamyaa Abd AL-Rahman

    2012-01-01

    Full Text Available Problem statement: An organic material is one of the major requirements to improve living environment and the invention of materials need to consider for the best solution. This study presents an experimental investigation on pure porous from Date Palm Fibre (DPF. The effectiveness of sound absorbers depends on structural architecture of this material. This study was conducted to examine the potential of using date palm fibre as sound absorber. The effects of porous layer thicknesses, densities and compression on Acoustic Absorption Coefficient (AAC of sound absorber using date palm fibre were studied. Approach: Rigid frame Johnson-Allard Model for various sample thicknesses was used in this study. The measurements were conducted in impedance tube on normal incidence acoustic absorption. The date palm fibre was mixed with latex which used for physical treatment on this material. Acoustic absorption behaviour of a porous material with different thicknesses was studied as well as samples with same thickness but different densities. In addition, samples with same properties but different period of compression time were inspected. The tests were in accordance to ISO 10534-2 and ASTM E1050-98 international standards for Acoustic Absorption Coefficient (AAC. Results: The experimental data indicates that two peak values of AAC is 0.93 at 1356Hz for sample with 50 mm thickness, also the AAC at high frequency for same thickness is 0.99 at 4200-4353 Hz that means able to improve acoustic absorption coefficient at low and high frequencies with significant increasing. Meanwhile, another experimental results were acquired for AAC of date palm fibre, with samples thicknesses of 35 mm at different densities .The results show that denser sample (11 Kg m-3 has higher AAC value of 0.83 at 1934- 2250 Hz as compared to less dense sample (9.92 Kg m-3 with AAC value 0.84 at 2443-2587 Hz . Conclusion: Acoustic absorption coefficient AAC of date palm fibre was

  12. Mechanical Properties of Air Plasma Sprayed Environmental Barrier Coating (EBC) Materials

    Science.gov (United States)

    Richards, Bradley; Zhu, Dongming; Ghosn, Louis; Wadley, Haydn

    2015-01-01

    Development work in Environmental Barrier Coatings (EBCs) for Ceramic Matrix Composites (CMCs) has focused considerably on the identification of materials systems and coating architectures to meet application needs. The evolution of these systems has occurred so quickly that modeling efforts and requisite data for modeling lag considerably behind development. Materials property data exists for many systems in the bulk form, but the effects of deposition on the critical properties of strength and fracture behavior are not well studied. We have plasma sprayed bulk samples of baseline EBC materials (silicon, ytterbium disilicate) and tested the mechanical properties of these materials to elicit differences in strength and toughness. We have also endeavored to assess the mixed-mode fracture resistance, Gc, of silicon in a baseline EBC applied to SiCSiC CMC via four point bend test. These results are compared to previously determined properties of the comparable bulk material.

  13. Numerical Simulation of the Mechanical Properties and Failure of Heterogeneous Elasto-Plastic Materials

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A general numerical approach was developed to simulate the mechanical properties and the failure of heterogeneous elasto-plastic materials using statistical distributions of the material properties. An appropriate elastic-plastic constitutive relation is used to describe the material behavior and failure in each element, with a two-parameter Weibull distribution used to produce the initial heterogeneous material property variations. An adaptive incremental load-step is applied so that only one or a few elements (or integration points) change their status (i.e., from elastic to plastic, or from plastic to strain failure) within one load step. A failed element is then assigned a very small modulus to simulate the failure rather than removing it from the model, which keeps the continuity of the geometric mesh. The numerical results show that the model is suitable for simulating the effective mechanical properties and failure of heterogeneous materials with local elasto-plastic constitutive relations.

  14. Broadband optical characterization of material properties

    DEFF Research Database (Denmark)

    Nielsen, Otto Højager Attermann

    , as well as details of the absorption spectrum which relate to chemical composition. The thesis focuses on two production process from the food industry. The first process is from the dairy industry where discrimination between chemical and structural properties is of importance. To explore...... inspection system for spectrallyresolved Static Light Scattering (SLS). (II) Photon Time-of-Flight (PToF) spectroscopy, which is a state of the art technique for characterization of turbid media. (III) A new hyperspectral imaging system based on full-field illumination by diffuse laser light. This thesis...... the fermentation process. It has also been shown that the optical inspection methods sense changes to structural properties before any are detected by traditional mechanical rheology. Finally, the developed hyperspectral imaging system was used to quantify the content of astaxanthin in fish feed, and performed...

  15. Mechanical Properties of Infrared Transmitting Materials

    Science.gov (United States)

    1978-01-01

    Theory of the Elasticity," 4th Edition, Dover Publ. Co., New York, N.Y., 1944. Marriott, J. B., and G. Rowden, "The Erosion of a Cobalt - Chromium Alloy...alumina (A1203), spinel (magnesium aluminate ), magnesia (MgO), yttria (Y203), as well as chemical vapor deposition (CVD) silicon carbide, CVD...known to be a problem. Because of their thermal and mechanical properties, alumina and magnesium aluminate (spinel) show, or can show, erosion

  16. Modeling skull electrical properties.

    Science.gov (United States)

    Sadleir, R J; Argibay, A

    2007-10-01

    Accurate representations and measurements of skull electrical conductivity are essential in developing appropriate forward models for applications such as inverse EEG or Electrical Impedance Tomography of the head. Because of its layered structure, it is often assumed that skull is anisotropic, with an anisotropy ratio around 10. However, no detailed investigation of skull anisotropy has been performed. In this paper we investigate four-electrode measurements of conductivities and their relation to tissue anisotropy ratio (ratio of tangential to radial conductivity) in layered or anisotropic biological samples similar to bone. It is shown here that typical values for the thicknesses and radial conductivities of individual skull layers produce tissue with much smaller anisotropy ratios than 10. Moreover, we show that there are very significant differences between the field patterns formed in a three-layered isotropic structure plausible for bone, and those formed assuming that bone is homogeneous and anisotropic. We performed a measurement of conductivity using an electrode configuration sensitive to the distinction between three-layered and homogeneous anisotropic composition and found results consistent with the sample being three-layered. We recommend that the skull be more appropriately represented as three isotropic layers than as homogeneous and anisotropic.

  17. Permittivity spectroscopy - an insight into materials properties.

    Science.gov (United States)

    Stoynov, Zdravko; Mladenova, Emiliya; Levi, Daniela; Vladikova, Daria

    2014-01-01

    Permittivity Spectroscopy is a branch of the Impedance Spectroscopy specially tuned for measurements and analyses of dielectrics permittivity properties. The present paper presents experimental results on permittivity properties of composite objects in which a polarizable dielectric is distributed in a fine non-polarizable matrix (solid or liquid) measured in frequency range 1 MHz down to 0.01 Hz. Two types of objects are studied - water in porous functional ceramics and lubricating oils. In both systems gigantic enhancement of the effective capacitance is observed. The first series of experiments was performed on porous membranes of yttrium doped barium cerate, which is a proton conducting ceramics with hydrophilic properties. At a given level of watering the measured capacitance is sharply increasing (3 to 5 orders of magnitude) in the lower frequency range. The second example covers permittivity study of lubricating oils, where the increase is 2-3 orders of magnitude. The phenomenon of gigantic enhancement of the effective capacitance could be related to a formation of dipole volume structures induced by the external alternating electrical field.

  18. Thermal and Electrical Properties of Nanocomposites, Including Material Properties

    NARCIS (Netherlands)

    Kochetov, R.

    2012-01-01

    The research described in this thesis is part of a state-funded IOP-EMVT project in cooperation with industrial companies, aiming at the design, assessment and implementation of new, environmental friendly (e.g. oil and SF6 - free) solid dielectric materials. A large disadvantage of solid polymer di

  19. Thermal and Electrical Properties of Nanocomposites, Including Material Properties

    NARCIS (Netherlands)

    Kochetov, R.

    2012-01-01

    The research described in this thesis is part of a state-funded IOP-EMVT project in cooperation with industrial companies, aiming at the design, assessment and implementation of new, environmental friendly (e.g. oil and SF6 - free) solid dielectric materials. A large disadvantage of solid polymer

  20. Recent Advances in the Sound Insulation Properties of Bio-based Materials

    OpenAIRE

    Xiaodong Zhu; Birm-June Kim; Qingwen Wang; Qinglin Wu

    2013-01-01

    Many bio-based materials, which have lower environmental impact than traditional synthetic materials, show good sound absorbing and sound insulation performances. This review highlights progress in sound transmission properties of bio-based materials and provides a comprehensive account of various multiporous bio-based materials and multilayered structures used in sound absorption and insulation products. Furthermore, principal models of sound transmission are discussed in order to aid in an ...

  1. Thin-Film Photoluminescent Properties and the Atomistic Model of Mg2TiO4 as a Non-rare Earth Matrix Material for Red-Emitting Phosphor

    Science.gov (United States)

    Huang, Chieh-Szu; Chang, Ming-Chuan; Huang, Cheng-Liang; Lin, Shih-kang

    2016-12-01

    Thin-film electroluminescent devices are promising solid-state lighting devices. Red light-emitting phosphor is the key component to be integrated with the well-established blue light-emitting diode chips for stimulating natural sunlight. However, environmentally hazardous rare-earth (RE) dopants, e.g. Eu2+ and Ce2+, are commonly used for red-emitting phosphors. Mg2TiO4 inverse spinel has been reported as a promising matrix material for "RE-free" red light luminescent material. In this paper, Mg2TiO4 inverse spinel is investigated using both experimental and theoretical approaches. The Mg2TiO4 thin films were deposited on Si (100) substrates using either spin-coating with the sol-gel process, or radio frequency sputtering, and annealed at various temperatures ranging from 600°C to 900°C. The crystallinity, microstructures, and photoluminescent properties of the Mg2TiO4 thin films were characterized. In addition, the atomistic model of the Mg2TiO4 inverse spinel was constructed, and the electronic band structure of Mg2TiO4 was calculated based on density functional theory. Essential physical and optoelectronic properties of the Mg2TiO4 luminance material as well as its optimal thin-film processing conditions were comprehensively reported.

  2. Thin-Film Photoluminescent Properties and the Atomistic Model of Mg2TiO4 as a Non-rare Earth Matrix Material for Red-Emitting Phosphor

    Science.gov (United States)

    Huang, Chieh-Szu; Chang, Ming-Chuan; Huang, Cheng-Liang; Lin, Shih-kang

    2016-08-01

    Thin-film electroluminescent devices are promising solid-state lighting devices. Red light-emitting phosphor is the key component to be integrated with the well-established blue light-emitting diode chips for stimulating natural sunlight. However, environmentally hazardous rare-earth (RE) dopants, e.g. Eu2+ and Ce2+, are commonly used for red-emitting phosphors. Mg2TiO4 inverse spinel has been reported as a promising matrix material for "RE-free" red light luminescent material. In this paper, Mg2TiO4 inverse spinel is investigated using both experimental and theoretical approaches. The Mg2TiO4 thin films were deposited on Si (100) substrates using either spin-coating with the sol-gel process, or radio frequency sputtering, and annealed at various temperatures ranging from 600°C to 900°C. The crystallinity, microstructures, and photoluminescent properties of the Mg2TiO4 thin films were characterized. In addition, the atomistic model of the Mg2TiO4 inverse spinel was constructed, and the electronic band structure of Mg2TiO4 was calculated based on density functional theory. Essential physical and optoelectronic properties of the Mg2TiO4 luminance material as well as its optimal thin-film processing conditions were comprehensively reported.

  3. Material characterization models and test methods for historic building materials

    DEFF Research Database (Denmark)

    Hansen, Tessa Kvist; Peuhkuri, Ruut Hannele; Møller, Eva B.

    2017-01-01

    Predictions of long term hygrothermal performance can be assessed by dynamic hygrothermal simulations, in which material parameters are crucial input. Material parameters for especially historic materials are often unknown; therefore, there is a need to determine important parameters, and simple...... ways for estimation of these. A case study of a brick wall was used to create and validate a hygrothermal simulation model; a parameter study with five different parameters was performed on this model to determine decisive parameters. Furthermore, a clustering technique has been proposed to estimate...

  4. Using regression models to determine the poroelastic properties of cartilage.

    Science.gov (United States)

    Chung, Chen-Yuan; Mansour, Joseph M

    2013-07-26

    The feasibility of determining biphasic material properties using regression models was investigated. A transversely isotropic poroelastic finite element model of stress relaxation was developed and validated against known results. This model was then used to simulate load intensity for a wide range of material properties. Linear regression equations for load intensity as a function of the five independent material properties were then developed for nine time points (131, 205, 304, 390, 500, 619, 700, 800, and 1000s) during relaxation. These equations illustrate the effect of individual material property on the stress in the time history. The equations at the first four time points, as well as one at a later time (five equations) could be solved for the five unknown material properties given computed values of the load intensity. Results showed that four of the five material properties could be estimated from the regression equations to within 9% of the values used in simulation if time points up to 1000s are included in the set of equations. However, reasonable estimates of the out of plane Poisson's ratio could not be found. Although all regression equations depended on permeability, suggesting that true equilibrium was not realized at 1000s of simulation, it was possible to estimate material properties to within 10% of the expected values using equations that included data up to 800s. This suggests that credible estimates of most material properties can be obtained from tests that are not run to equilibrium, which is typically several thousand seconds.

  5. Interfacial properties and design of functional energy materials.

    Science.gov (United States)

    Sumpter, Bobby G; Liang, Liangbo; Nicolaï, Adrien; Meunier, Vincent

    2014-11-18

    CONSPECTUS: The vital importance of energy to society continues to demand a relentless pursuit of energy responsive materials that can bridge fundamental chemical structures at the molecular level and achieve improved functionality and performance. This demand can potentially be realized by harnessing the power of self-assembly, a spontaneous process where molecules or much larger entities form ordered aggregates as a consequence of predominately noncovalent (weak) interactions. Self-assembly is the key to bottom-up design of molecular devices, because the nearly atomic-level control is very difficult to realize in a top-down, for example, lithographic, approach. However, while function in simple systems such as single crystals can often be evaluated a priori, predicting the function of the great variety of self-assembled molecular architectures is complicated by the lack of understanding and control over nanoscale interactions, mesoscale architectures, and macroscale order. To establish a foundation toward delivering practical solutions, it is critical to develop an understanding of the chemical and physical mechanisms responsible for the self-assembly of molecular and hybrid materials on various support substrates. Typical molecular self-assembly involves noncovalent intermolecular and substrate-molecule interactions. These interactions remain poorly understood, due to the combination of many-body interactions compounded by local or collective influences from the substrate atomic lattice and electronic structure. Progress toward unraveling the underlying physicochemical processes that control the structure and macroscopic physical, chemical, mechanical, electrical, and transport properties of materials increasingly requires tight integration of theory, modeling, and simulation with precision synthesis, advanced experimental characterization, and device measurements. Theory, modeling, and simulation can accelerate the process of materials understanding and design

  6. Quality quantification model of basic raw materials

    OpenAIRE

    Š. Vilamová; P. Besta; R. Kozel; K. Janovská; M. Piecha; Levit, A; Straka, M.; Šanda, M.

    2016-01-01

    Basic raw materials belong to the key input sources in the production of pig iron. The properties of basic raw materials can be evaluated using a variety of criteria. The essential ones include the physical and chemical properties. Current competitive pressures, however, force the producers of iron more and more often to include cost and logistic criteria into the decision-making process. In this area, however, they are facing a problem of how to convert a variety of vastly differ...

  7. Spectroscopic properties of rare earths in optical materials

    CERN Document Server

    Parisi, Jürgen; Osgood, R; Warlimont, Hans; Liu, Guokui; Jacquier, Bernard

    2005-01-01

    Aimed at researchers and graduate students, this book provides up-to-date information for understanding electronic interactions that impact the optical properties of rare earth ions in solids. Its goal is to establish a connection between fundamental principles and the materials properties of rare-earth activated luminescent and laser optical materials. The theoretical survey and introduction to spectroscopic properties include electronic energy level structure, intensities of optical transitions, ion-phonon interactions, line broadening, and energy transfer and up-conversion. An important aspect of the book lies in its deep and detailed discussions on materials properties and the potential of new applications such as optical storage, information processing, nanophotonics, and molecular probes that have been identified in recent experimental studies. This volume will be a valuable reference book on advanced topics of rare earth spectroscopy and materials science.

  8. Interdisciplinary research concerning the nature and properties of ceramic materials

    Science.gov (United States)

    1975-01-01

    The nature and properties of ceramic materials as they relate to solid state physics and metallurgy are studied. Special attention was given to the applications of ceramics to NASA programs and national needs.

  9. Molecular modeling and multiscaling issues for electronic material applications

    CERN Document Server

    Iwamoto, Nancy; Yuen, Matthew; Fan, Haibo

    Volume 1 : Molecular Modeling and Multiscaling Issues for Electronic Material Applications provides a snapshot on the progression of molecular modeling in the electronics industry and how molecular modeling is currently being used to understand material performance to solve relevant issues in this field. This book is intended to introduce the reader to the evolving role of molecular modeling, especially seen through the eyes of the IEEE community involved in material modeling for electronic applications.  Part I presents  the role that quantum mechanics can play in performance prediction, such as properties dependent upon electronic structure, but also shows examples how molecular models may be used in performance diagnostics, especially when chemistry is part of the performance issue.  Part II gives examples of large-scale atomistic methods in material failure and shows several examples of transitioning between grain boundary simulations (on the atomistic level)and large-scale models including an example ...

  10. Outgassing Properties of Chemically Polished Titanium Materials

    Science.gov (United States)

    Kurisu, Hiroki; Kimoto, Gou; Fujii, Hiroaki; Tanaka, Kazuhiko; Yamamoto, Setsuo; Matsuura, Mitsuru; Ishizawa, Katsunobu; Nomura, Takeru; Murashige, Nobuyuki

    We developed a chemical polishing (CP) for titanium materials applicable to ultrahigh vacuum (UHV) and extremely high vacuum (XHV) systems. The surface roughness, Ra, of the chemically polished titanium is obtained to be 25 nm by the atomic force microscopy measurement. This value is smaller than those of the base metal (BM) and the buff-polished (BP) samples. The thickness of the surface oxide layer of CP sample is estimated to be 7 nm by the cross section of transmission electron micrograph. Amount of desorption gas of CP sample obtained by the thermal desorption measurement is smaller than those of BM and BP sample, and is the same as that of the mechanochemically polished (MCP) sample. The outgassing rate of CP sample after baking at 150°C×20 h is obtained to be 7×10-13 Pa•m•s-1. This value is lower than that of standard vacuum materials by two orders of magnitude after the ordinary baking.

  11. Models of electromagnetic properties of composite media

    Science.gov (United States)

    Liu, Jin

    Electromagnetic composite materials have attracted much interest in recent years, due to their desirable microwave and optical applications. One class of these is negative refractive index materials, or double negative materials, in which both permittivity and permeability of materials are simultaneously negative. Many exciting potential applications of double negative materials have been proposed, such as the perfect lens and the cloaking device. Here, a simple-cubic lattice of identical, homogeneous or coated non-metallic spherical particles embedded in a matrix is analyzed. One contribution of this work is the derivation of an analytical formula for the threshold dielectric loss angle of spherical inclusions, above which DNG behavior of the system is extinguished. In addition, analytical formulas are derived from which double negative bandwidth of a simple-cubic lattice of identical, magnetodielectric homogeneous or coated spheres can be determined. Another case of interest is nanocomposites, which commonly consist of nanoparticles embedded in a polymer matrix. These materials show superior dielectric or mechanical performance by taking advantage of the merits of their individual non-hybrid components. In one manifestation, diblock copolymers can be utilized to spatially separate nanoparticles by incorporating them in one block, preferentially, to form a long-range ordered structure. By designing this structure, the electromagnetic properties can be tailored for potential applications in novel devices. Here, molecular dynamics of polymer matrices and nanocomposites is analyzed by parametric modeling of their dielectric spectra, supporting design of a composite with desired electromagnetic properties.

  12. ROCK PROPERTIES MODEL ANALYSIS MODEL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    Clinton Lum

    2002-02-04

    The purpose of this Analysis and Model Report (AMR) is to document Rock Properties Model (RPM) 3.1 with regard to input data, model methods, assumptions, uncertainties and limitations of model results, and qualification status of the model. The report also documents the differences between the current and previous versions and validation of the model. The rock properties models are intended principally for use as input to numerical physical-process modeling, such as of ground-water flow and/or radionuclide transport. The constraints, caveats, and limitations associated with this model are discussed in the appropriate text sections that follow. This work was conducted in accordance with the following planning documents: WA-0344, ''3-D Rock Properties Modeling for FY 1998'' (SNL 1997, WA-0358), ''3-D Rock Properties Modeling for FY 1999'' (SNL 1999), and the technical development plan, Rock Properties Model Version 3.1, (CRWMS M&O 1999c). The Interim Change Notice (ICNs), ICN 02 and ICN 03, of this AMR were prepared as part of activities being conducted under the Technical Work Plan, TWP-NBS-GS-000003, ''Technical Work Plan for the Integrated Site Model, Process Model Report, Revision 01'' (CRWMS M&O 2000b). The purpose of ICN 03 is to record changes in data input status due to data qualification and verification activities. These work plans describe the scope, objectives, tasks, methodology, and implementing procedures for model construction. The constraints, caveats, and limitations associated with this model are discussed in the appropriate text sections that follow. The work scope for this activity consists of the following: (1) Conversion of the input data (laboratory measured porosity data, x-ray diffraction mineralogy, petrophysical calculations of bound water, and petrophysical calculations of porosity) for each borehole into stratigraphic coordinates; (2) Re-sampling and merging of data sets; (3

  13. A Reference Guide for Cryogenic Properties of Materials

    Energy Technology Data Exchange (ETDEWEB)

    Weisend, John G

    2003-09-16

    A thorough knowledge of the behavior of materials at cryogenic temperatures is critical for the design of successful cryogenic systems. Over the past 50 years, a tremendous amount of material properties at cryogenic temperatures have been measured and published. This guide lists resources for finding these properties. It covers online databases, computer codes, conference proceedings, journals, handbooks, overviews and monographs. It includes references for finding reports issued by government laboratories and agencies. Most common solids and fluids used in cryogenics are covered.

  14. Cellular and Porous Materials Thermal Properties Simulation and Prediction

    CERN Document Server

    Öchsner, Andreas; de Lemos, Marcelo J S

    2008-01-01

    Providing the reader with a solid understanding of the fundamentals as well as an awareness of recent advances in properties and applications of cellular and porous materials, this handbook and ready reference covers all important analytical and numerical methods for characterizing and predicting thermal properties. In so doing it directly addresses the special characteristics of foam-like and hole-riddled materials, combining theoretical and experimental aspects for characterization purposes.

  15. INVESTIGATION OF TRIBOLOGICAL PROPERTIES CuSn10 BEARING MATERIAL

    OpenAIRE

    2005-01-01

    Bronzes which copper based alloys is widely used because of properties physical, thermal and tribological as journal bearing material. This material that has tribological performance good conclusions gives at journal bearings. In this study, CuSn10 bronze that were manufactured journal bearings friction and wear properties has been examined and compared. SAE 1050 steel shaft has been used as counter abrader. Experiments have been carried out 10 N and 20 N loads, 750 and 1500 rpm, dry and lubr...

  16. Surface properties of copper based cermet materials

    Energy Technology Data Exchange (ETDEWEB)

    Voinea, M. [The Centre: Product Design for Sustainable Development, Transilvania University of Brasov, Eroilor 29, 500036 (Romania)], E-mail: m.voinea@unitbv.ro; Vladuta, C.; Bogatu, C.; Duta, A. [The Centre: Product Design for Sustainable Development, Transilvania University of Brasov, Eroilor 29, 500036 (Romania)

    2008-08-25

    The paper presents the characterization of the surface properties of copper based cermets obtained by two different techniques: spray pyrolysis deposition (SPD) and electrodeposition. Copper acetate was used as precursor of Cu/CuO{sub x} cermet. The surface morphology was tailored by adding copolymers of maleic anhydride with controlled hydrophobia. The films morphology of Cu/CuO{sub x} was assessed using contact angle measurements and AFM analysis. The porous structures obtained via SPD lead to higher liquid adsorption rate than the electrodeposited films. A highly polar liquid - water is recommended as testing liquid in contact angle measurements, for estimating the porosity of copper based cermets, while glycerol can be used to distinguish among ionic and metal predominant structures. Thus, contact angle measurements can be used for a primary evaluation of the films morphology and, on the other hand, of the ratio between the cermet components.

  17. Novel thermal properties of nanostructured materials.

    Energy Technology Data Exchange (ETDEWEB)

    Eastman, J. A.

    1999-01-13

    A new class of heat transfer fluids, termed nanofluids, has been developed by suspending nanocrystalline particles in liquids. Due to the orders-of-magnitude larger thermal conductivities of solids compared to those of liquids such as water, significantly enhanced thermal properties are obtained with nanofluids. For example, an approximately 20% improvement in effective thermal conductivity is observed when 5 vol.% CuO nanoparticles are added to water. Even more importantly, the heat transfer coefficient of water under dynamic flow conditions is increased more than 15% with the addition of less than 1 vol.% CuO particles. The use of nanofluids could impact many industrial sectors, including transportation, energy supply and production, electronics, textiles, and paper production by, for example, decreasing pumping power needs or reducing heat exchanger sizes. In contrast to the enhancement in effective thermal transport rates that is obtained when nanoparticles are suspended in fluids, nanocrystalline coatings are expected to exhibit reduced thermal conductivities compared to coarse-grained coatings. Reduced thermal conductivities are predicted to arise because of a reduction in the mean free path of phonons due to presence of grain boundaries. This behavior, combined with improved mechanical properties, makes nanostructured zirconia coatings excellent candidates for future applications as thermal barriers. Yttria-stabilized zirconia (YSZ) thin films are being produced by metal-organic chemical vapor deposition techniques. Preliminary results have indicated that the thermal conductivity is reduced by approximately a factor-of-two at room temperature in 10 nm grain-sized YSZ compared to coarse-grained or single crystal YSZ.

  18. Solder joint technology materials, properties, and reliability

    CERN Document Server

    Tu, King-Ning

    2007-01-01

    Solder joints are ubiquitous in electronic consumer products. The European Union has a directive to ban the use of Pb-based solders in these products on July 1st, 2006. There is an urgent need for an increase in the research and development of Pb-free solders in electronic manufacturing. For example, spontaneous Sn whisker growth and electromigration induced failure in solder joints are serious issues. These reliability issues are quite complicated due to the combined effect of electrical, mechanical, chemical, and thermal forces on solder joints. To improve solder joint reliability, the science of solder joint behavior under various driving forces must be understood. In this book, the advanced materials reliability issues related to copper-tin reaction and electromigration in solder joints are emphasized and methods to prevent these reliability problems are discussed.

  19. Liquid Crystalline Semiconductors Materials, properties and applications

    CERN Document Server

    Kelly, Stephen; O'Neill, Mary

    2013-01-01

    This is an exciting stage in the development of organic electronics. It is no longer an area of purely academic interest as increasingly real applications are being developed, some of which are beginning to come on-stream. Areas that have already been commercially developed or which are under intensive development include organic light emitting diodes (for flat panel displays and solid state lighting), organic photovoltaic cells, organic thin film transistors (for smart tags and flat panel displays) and sensors. Within the family of organic electronic materials, liquid crystals are relative newcomers. The first electronically conducting liquid crystals were reported in 1988 but already a substantial literature has developed. The advantage of liquid crystalline semiconductors is that they have the easy processability of amorphous and polymeric semiconductors but they usually have higher charge carrier mobilities. Their mobilities do not reach the levels seen in crystalline organics but they circumvent all of t...

  20. Organoapatites: materials for artificial bone. II. Hardening reactions and properties.

    Science.gov (United States)

    Stupp, S I; Mejicano, G C; Hanson, J A

    1993-03-01

    This article reports on chemical reactions and the properties they generated in artificial bone materials termed "organoapatites." These materials are synthesized using methodology we reported in the previous article of this series. Two different processes were studied here for the transition from organoapatite particles to implants suitable for the restoration of the skeletal system. One process involved the hardening of powder compacts by beams of blue light derived from a lamp or a laser and the other involved pressure-induced interdiffusion of polymers. In both cases, the hardening reaction involved the formation of a polyion complex between two polyelectrolytes. In the photo-induced reaction an anionic electrolyte polymerizes to form the coulombic network and in the pressure-induced one, pressure forms the complex by interdiffusion of two polyions. Model reactions were studied using various polycations. Based on these results the organoapatite selected for the study was that containing dispersed poly(L-lysine) and sodium acrylate as the anionic monomer. The organomineral particles can be pressed at room temperature into objects of great physical integrity and hydrolytic stability relative to anorganic controls. The remarkable fact about these objects is that intimate molecular dispersion of only 2-3% by weight organic material provides integrity to the mineral network in an aqueous medium and also doubles its tensile strength. This integrity is essentially nonexistent in "anorganic" samples prepared by the same methodology used in organoapatite synthesis. The improvement in properties was most effectively produced by molecular bridges formed by photopolymerization. The photopolymerization leads to the "hardening" of pellets prepared by pressing of organoapatite powders. The reaction was found to be more facile in the microstructure of the organomineral, and it is potentially useful in the surgical application of organoapatites as artificial bone.

  1. Report on modelling and materials

    CERN Document Server

    EuCARD, Collaboration

    2014-01-01

    The WP8 aims at the design of advanced materials and collimators to allow for higher beam power in state-of-the-art accelerator facilities. Task 8.2 in particular focuses on the research, development, production, characterization and testing of novel materials for advanced thermal management applications primarily devoted to future Phase II Collimators, but having the potential to be applied to a much broader spectrum of applications. A broad variety of materials has been studied, produced and characterized, including metal-diamond composites such as Copper-Diamond, Silver-Diamond, Molybdenum-Diamond as well as Molybdenum-Graphite composites with very promising results. Advanced numerical simulation techniques have been used to study the behaviour of these, as well as more traditional materials under the effect of very intense, highly energetic particle beams. An intensive testing programme is being deployed to verify their behaviour under extreme conditions.

  2. Basis Function Sampling: A New Paradigm for Material Property Computation

    Science.gov (United States)

    Whitmer, Jonathan K.; Chiu, Chi-cheng; Joshi, Abhijeet A.; de Pablo, Juan J.

    2014-11-01

    Wang-Landau sampling, and the associated class of flat histogram simulation methods have been remarkably helpful for calculations of the free energy in a wide variety of physical systems. Practically, convergence of these calculations to a target free energy surface is hampered by reliance on parameters which are unknown a priori. Here, we derive and implement a method built upon orthogonal functions which is fast, parameter-free, and (importantly) geometrically robust. The method is shown to be highly effective in achieving convergence. An important feature of this method is its ability to attain arbitrary levels of description for the free energy. It is thus ideally suited to in silico measurement of elastic moduli and other material properties related to free energy perturbations. We demonstrate the utility of such applications by applying our method to calculate the Frank elastic constants of the Lebwohl-Lasher model of liquid crystals.

  3. Modeling pyrolysis of charring material in fire

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A modified model of pyrolysis for charring materials in fire has been proposed in this note. In this model some special factors which show the effect on pyrolysis are considered, i.e. heat loss by convection and radiation caused by surface temperature rise and shrinkage of char surface are considered. Experimental device is designed specially for validating the reliability of the model. Effects of density of materials and heat radiation on pyrolysis of materials have also been investigated.

  4. Materials Selection, Synthesis, and Dielectrical Properties of PVC Nanocomposites

    OpenAIRE

    Youssef Mobarak; Bassyouni, M.; Almutawa, M.

    2013-01-01

    Materials selection process for electrical insulation application was carried out using Cambridge Engineering Selector (CES) program. Melt mixing technique was applied to prepare polyvinyl-chloride- (PVC-) nanofumed silica and nanomontmorillonite clay composites. Surface analysis and particles dispersibility were examined using scanning electron microscope. Dielectrical properties were assessed using Hipot tester. An experimental work for dielectric loss of the nanocomposite materials has bee...

  5. Understanding Materials Science History · Properties · Applications

    CERN Document Server

    Hummel, Rolf E

    2005-01-01

    This introduction to materials science both for students of engineering and physics and for the interested general public examines not only the physical and engineering properties of virtually all kinds of materials, but also their history, uses, development, and some of the implications of resource depletion and recycling. It covers all topics on materials from an entirely novel perspective: the role materials have played throughout history in the development of humankind and technologies. Specifically, it shows the connection between the technical and the cultural, economic, ecological, and societal aspects of materials science. It aims to whet the appetite of its readers and inspire them to further explore the properties and applications of metals, alloys, ceramics, plastics, and electronic materials by presenting easily understandable explanations and entertaining historical facts. It is also intended to raise the reader’s awareness of their obligations to society as practicing engineers and scientists....

  6. OM85. Basic Properties of Optical Materials Summaries of Papers.

    Science.gov (United States)

    1985-05-01

    Optical Properties of Solids (Academic, New York, 1972) Ch.3. 7. D.B. Tanner, A.J...12, (1973). 6. T. Fleisch and R. Abermann, Thin Solid FilffF-42, 255-263 (1977). 7. F. Wooten, Optical Properties of Solids (Academic Press, New York...resolve cp structure. Such mea- surements are still lacking for many common semiconducting materials. REFERENCES 1. D.E. Aspnes, in Optical Properties of Solids :

  7. A Quantitative Property-Property Relationship for the Internal Diffusion Coefficients of Organic Compounds in Solid Materials

    DEFF Research Database (Denmark)

    Huang, Lei; Fantke, Peter; Jolliet, Olivier

    2017-01-01

    Indoor releases of organic chemicals encapsulated in solid materials are major contributors to human exposures and are directly related to the internal diffusion coefficient in solid materials. Existing correlations to estimate the diffusion coefficient are only valid for a limited number...... of chemical-material combinations. This paper develops and evaluates a quantitative property-property relationship (QPPR) to predict diffusion coefficients for a wide range of organic chemicals and materials. We first compiled a training dataset of 1103 measured diffusion coefficients for 158 chemicals in 32...... consolidated material types. Following a detailed analysis of the temperature influence, we developed a multiple linear regression model to predict diffusion coefficients as a function of chemical molecular weight (MW), temperature, and material type (adjusted R2 of 0.93). The internal validations showed...

  8. Significance of tests and properties of concrete and concrete-making materials

    CERN Document Server

    Pielert, James H

    2006-01-01

    Reflects a decade of technological changes in concrete industry! The newest edition of this popular ASTM publication reflects the latest technology in concrete and concrete-making materials. Six sections cover: (1) General information on the nature of concrete, sampling, variability, and testing laboratories. A new chapter deals with modeling cement and concrete properties. (2) Properties of freshly mixed concrete. (3) Properties of hardened concrete. (4) Concrete aggregates—this section has been revised and the chapters are presented in the order that most concerns concrete users: grading, density, soundness, degradation resistance, petrographic examination, reactivity, and thermal properties. (5) Materials other than aggregates—the chapter on curing materials now reflects the current technology of materials applied to new concrete surfaces. The chapter on mineral admixtures has been separated into two chapters: supplementary cementitious materials and ground slag. (6) Specialized concretes—contains a ...

  9. Grain size dependent mechanical properties in nanophase materials

    Energy Technology Data Exchange (ETDEWEB)

    Siegel, R.W. [Argonne National Lab., IL (United States); Fougere, G.E. [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering

    1995-02-01

    It has become possible in recent years to synthesize metals and ceramics under well controlled conditions with constituent grain structures on a manometer size scale (below 100 nm). These new materials have mechanical properties that are strongly grain-size dependent and often significantly different than those of their coarser grained counterparts. Nanophase metals tend to become stronger and ceramics are more easily deformed as grain size is reduced. The observed mechanical property changes appear to be related primarily to grain size limitations and the large percentage of atoms in grain boundary environments. A brief overview of our present knowledge about the grain-size dependent mechanical properties of nanophase materials is presented.

  10. Tunneling properties of electromagnetic wave in slab superconducting material

    Institute of Scientific and Technical Information of China (English)

    Khem B. Thapa; Sanjay Srivastava; Alka Vishwakarma; S. P. Ojha

    2011-01-01

    When the electromagnetic wave propagates through a slab superconducting material in microwave ranges, tunneling properties of the electromagnetic wave at critical temperature are investigated theoretically. The transmittance and the reflectance of the slab superconducting material vary with the thickness of material as well as the refractive index of substrates.The high transmittance is found for thin superconductor at low wavelength region.However, optical properties are strongly dependent upon temperature and incidence wavelength. The electromagnetic wave is totally transmitted without loss for incidence wavelength (λ = 5000 nm) due to the zero refractive index and infinite penetration depth of the superconductor at the critical temperature.

  11. Surface structure and electronic properties of materials

    Science.gov (United States)

    Siekhaus, W. J.; Somorjai, G. A.

    1975-01-01

    A surface potential model is developed to explain dopant effects on chemical vapor deposition. Auger analysis of the interaction between allotropic forms of carbon and silicon films has shown Si-C formation for all forms by glassy carbon. LEED intensity measurements have been used to determine the mean square displacement of surface atoms of silicon single crystals, and electron loss spectroscopy has shown the effect of structure and impurities on surface states located within the band gap. A thin film of Al has been used to enhance film crystallinity at low temperature.

  12. Properties of Materials Using Acoustic Waves.

    Science.gov (United States)

    1984-10-01

    CLASSiFICATIOO OF THIS PAGIR elM. DMe Eatae" to nonlinear acoustics which should permit us to cast problems with geometric and other complexities into a...on the kinetics of chemical reactions . 5. New theoretical approaches in nonlinear acoustics (R.M. McGowan and Professor B.-T. Chu) We are working to...of water and methanol was compared with the theoretical predictions given by Marston’s theory and the simplified model (Hsu 1983). This set of data

  13. Method for obtaining simple shear material properties of the intervertebral disc under high strain rates.

    Science.gov (United States)

    Ott, Kyle A; Armiger, Robert S; Wickwire, Alexis C; Carneal, Catherine M; Trexler, Morgana M; Lennon, Andrew M; Zhang, Jiangyue; Merkle, Andrew C

    2012-01-01

    Predicting spinal injury under high rates of vertical loading is of interest, but the success of computational models in modeling this type of loading scenario is highly dependent on the material models employed. Understanding the response of these biological materials at high strain rates is critical to accurately model mechanical response of tissue and predict injury. While data exists at lower strain rates, there is a lack of the high strain rate material data that are needed to develop constitutive models. The Split Hopkinson Pressure Bar (SHPB) has been used for many years to obtain properties of various materials at high strain rates. However, this apparatus has mainly been used for characterizing metals and ceramics and is difficult to apply to softer materials such as biological tissue. Recently, studies have shown that modifications to the traditional SHPB setup allow for the successful characterization of mechanical properties of biological materials at strain rates and peak strain values that exceed alternate soft tissue testing techniques. In this paper, the previously-reported modified SHPB technique is applied to characterize human intervertebral disc material under simple shear. The strain rates achieved range from 5 to 250 strain s-1. The results demonstrate the sensitivity to the disc composition and structure, with the nucleus pulposus and annulus fibrosus exhibiting different behavior under shear loading. Shear tangent moduli are approximated at varying strain levels from 5 to 20% strain. This data and technique facilitates determination of mechanical properties of intervertebral disc materials under shear loading, for eventual use in constitutive models.

  14. SEWABILITY PROPERTIES OF GARMENT LEATHERS TANNED WITH VARIOUS TANNING MATERIALS

    Directory of Open Access Journals (Sweden)

    ORK Nilay

    2016-05-01

    Full Text Available Chromium tannage is the most used technology in processing of garment leathers. Due to environmental requirements and demands on natural products there is an increasing interest on alternatives to chromium tannage especially on vegetable tanned leathers. Leather properties vary in a very wide range depending on the animal type it is obtained from and the process type and chemicals used in the manufacturing. In this study, the effect of various tanning materials to the sewability of garment leathers was investigated. For this purpose, vegetable, chromium and chromium-vegetable combination tanned garment leathers from the same animal origin were supplied from a garment leather manufacturing factory. Needle penetration force and the sewability values of these leathers were determined by using L&M Sewability Tester. It was found that material properties and sewing properties showed differences regarding to the tanning material used even in same type of raw material. Chromium tanned leathers had sewability values of 13.4% horizontal and 14.2% vertical which are considered good to fair. Vegetable tanned leathers and chromium-vegetable tanned leathers had sewability values of 38.2% horizontal, 49.2% vertical and 98% horizontal, 98.5% vertical respectively which are considered poor. The results of the study conclude that, there is a big difference in material properties when the tanning technology and material is changed which also affects the sewing properties.

  15. Thermal effects of variable material properties and metamorphic reactions in a three-component subducting slab

    DEFF Research Database (Denmark)

    Chemia, Zurab; Dolejš, David; Steinle-Neumann, Gerd

    2015-01-01

    We explore the effects of variable material properties, phase transformations, and metamorphic devolatilization reactions on the thermal structure of a subducting slab using thermodynamic phase equilibrium calculations combined with a thermal evolution model. The subducting slab is divided...... into three layers consisting of oceanic sediments, altered oceanic crust, and partially serpentinized or anhydrous harzburgite. Solid-fluid equilibria and material properties are computed for each layer individually to illustrate distinct thermal consequences when chemical and mechanical homogenization...

  16. High Temperature Thermoelectric Properties of ZnO Based Materials

    DEFF Research Database (Denmark)

    Han, Li

    This thesis investigated the high temperature thermoelectric properties of ZnO based materials. The investigation first focused on the doping mechanisms of Al-doped ZnO, and then the influence of spark plasma sintering conditions on the thermoelectric properties of Al, Ga-dually doped ZnO....... Following that, the nanostructuring effect for Al-doped ZnO was systematically investigated using samples with different microstructure morphologies. At last, the newly developed ZnCdO materials with superior thermoelectric properties and thermal stability were introduced as promising substitutions...... for conventional ZnO materials. For Al-doped ZnO, α- and γ-Al2O3 were selectively used as dopants in order to understand the doping mechanism of each phase and their effects on the thermoelectric properties. The samples were prepared by the spark plasma sintering technique from precursors calcined at various...

  17. Material Properties of the Mandibular Trabecular Bone

    Science.gov (United States)

    Lakatos, Éva; Magyar, Lóránt; Bojtár, Imre

    2014-01-01

    The present paper introduces a numerical simulation aided, experimental method for the measurement of Young's modulus of the trabecular substance in the human mandible. Compression tests were performed on fresh cadaveric samples containing trabecular bone covered with cortical layer, thus avoiding the destruction caused by the sterilization, preservation, and storage and the underestimation of the stiffness resulting from the individual failure of the trabeculae cut on the surfaces. The elastic modulus of the spongiosa was determined by the numerical simulation of each compression test using a specimen specific finite element model of each sample. The received mandibular trabecular bone Young's modulus values ranged from 6.9 to 199.5 MPa. PMID:27006933

  18. Basis Function Sampling for Material Property Computations

    Science.gov (United States)

    Whitmer, Jonathan K.; Chiu, Chi-Cheng; Joshi, Abhijeet A.; de Pablo, Juan J.

    2014-03-01

    Wang-Landau sampling, and the associated class of flat histogram simulation methods, have been particularly successful for free energy calculations in a wide array of physical systems. Practically, the convergence of these calculations to a target free energy surface is hampered by reliance on parameters which are unknown a priori. We derive and implement a method based on orthogonal (basis) functions which is fast, parameter-free, and geometrically robust. An important feature of this method is its ability to achieve arbitrary levels of description for the free energy. It is thus ideally suited to in silico measurement of elastic moduli and other quantities related to free energy perturbations. We demonstrate the utility of such applications by applying our method to calculation of the Frank elastic constants of the Lebwohl-Lasher model.

  19. Material Properties of the Mandibular Trabecular Bone

    Directory of Open Access Journals (Sweden)

    Éva Lakatos

    2014-01-01

    Full Text Available The present paper introduces a numerical simulation aided, experimental method for the measurement of Young’s modulus of the trabecular substance in the human mandible. Compression tests were performed on fresh cadaveric samples containing trabecular bone covered with cortical layer, thus avoiding the destruction caused by the sterilization, preservation, and storage and the underestimation of the stiffness resulting from the individual failure of the trabeculae cut on the surfaces. The elastic modulus of the spongiosa was determined by the numerical simulation of each compression test using a specimen specific finite element model of each sample. The received mandibular trabecular bone Young’s modulus values ranged from 6.9 to 199.5 MPa.

  20. Viscoelastic effective properties of two types of heterogeneous materials.

    Science.gov (United States)

    Cornet, Jan; Dabrowski, Marcin; Schmid, Daniel

    2015-04-01

    In the past, a lot of efforts have been put to describe two end cases of rock behaviors: elasticity and viscosity. In recent years, more focus has been brought on the intermediate viscoelastic cases which describe better the rheology of rocks such as shales. Shales are typically heterogeneous and the question arises as to how to derive their effective properties so that they can be approximated as homogeneous media. This question has already been dealt with at the elastic and viscous limit but still remains for some cases in between. Using MILAMIN, a fast finite element solver for large problems, we numerically investigate different approaches to derive the effective properties of several viscoelastic media. Two types of geometries are considered: layered and inclusion based media. We focus on two dimensional plane strain problems considering two phase composites deformed under pure shear. We start by investigating the case of transversely isotropic layered media made of two Maxwell materials. Using the Backus averaging method we discuss the degree of relevance of this averaging by considering some parameters as: layer periodicity, layer thickness and layer interface roughness. Other averaging methods are also discussed which provide a broader perspective on the performances of Backus averaging. In a second part we move on to inclusion based models. The advantage of these models compared to the previous one is that they provide a better approximation to real microstructures in rocks. The setup we consider in this part is the following: some viscous circular inclusions are embedded in an elastic matrix. Both the inclusions and the matrix are homogeneous but the inclusions are purely isotropic while the matrix can also be anisotropic. In order to derive the effective viscoelastic properties of the medium we use two approaches: the self-consistent averaging and the differential effective medium theory. The idea behind self-consistency is to assume that the inclusions

  1. Dielectric properties of tissues and biological materials: a critical review.

    Science.gov (United States)

    Foster, K R; Schwan, H P

    1989-01-01

    We critically review bulk electrical properties of tissues and other biological materials, from DC to 20 GHz, with emphasis on the underlying mechanisms responsible for the properties. We summarize the classical principles behind dielectric relaxation and critically review recent developments in this field. Special topics include a summary of the significant recent advances in theories of counterion polarization effects, dielectric properties of cancer vs. normal tissues, properties of low-water-content tissues, and macroscopic field-coupling considerations. Finally, the dielectric properties of tissues are summarized as empirical correlations with tissue water content in other compositional variables; in addition, a comprehensive table is presented of dielectric properties. The bulk electrical properties of tissues are needed for many bioengineering applications of electric fields or currents, and they provide insight into the basic mechanisms that govern the interaction of electric fields with tissue.

  2. Effects of bituminous layer as backfill material on mechanical behavior in tunnel model

    OpenAIRE

    Moriyoshi, Akihiro; Takano, Shin-ei; Urata, Hiroyuki; Suzuki, Tetsuya; Yoshida, Takaki

    2001-01-01

    This paper describes the effects of bituminous material as a backfill material on mechanical behavior in model tunnel in laboratory. It is known that load spreading and relaxation of bituminous material are good properties. Then if we use bituminous material as a backfill material of tunnel, the tunnel will have waterproof, good load spreading property. We used new bituminous material (Aquaphalt) which can solidify in water. We conducted relaxation test in tension for new bituminous mat...

  3. Computational Materials: Modeling and Simulation of Nanostructured Materials and Systems

    Science.gov (United States)

    Gates, Thomas S.; Hinkley, Jeffrey A.

    2003-01-01

    The paper provides details on the structure and implementation of the Computational Materials program at the NASA Langley Research Center. Examples are given that illustrate the suggested approaches to predicting the behavior and influencing the design of nanostructured materials such as high-performance polymers, composites, and nanotube-reinforced polymers. Primary simulation and measurement methods applicable to multi-scale modeling are outlined. Key challenges including verification and validation of models are highlighted and discussed within the context of NASA's broad mission objectives.

  4. Investigation of thermal properties of raw materials of asphalt mixtures

    Science.gov (United States)

    Géber, R.; Simon, A.; Kocserha, I.

    2017-02-01

    Asphalt mixtures are composite materials, which are made of different grades of mineral aggregates and bitumen. During the mixing process mineral materials were blended with bitumen at relatively high temperature (∼200 °C). As the binding process come off in these higher temperature range, thermal properties of asphaltic materials are important. The aim of this project is to reveal the thermal properties of raw materials. During our research two types of mineral aggregates were tested (limestone and dolomite) by different methods. Differential thermal analysis, thermal expansion and thermal conductivity were investigated at technologically important temperatures. The results showed that the structure of mineral materials did not change at elevated temperatures, expansion of samples was neglible, while thermal conductivity changed by temperature.

  5. A Summary of the Fatigue Properties of Wind Turbine Materials

    Energy Technology Data Exchange (ETDEWEB)

    SUTHERLAND, HERBERT J.

    1999-10-07

    Modern wind turbines are fatigue critical machines that are typically used to produce electrical power from the wind. The materials used to construct these machines are subjected to a unique loading spectrum that contains several orders of magnitude more cycles than other fatigue critical structures, e.g., an airplane. To facilitate fatigue designs, a large database of material properties has been generated over the past several years that is specialized to materials typically used in wind turbines. In this paper, I review these fatigue data. Major sections are devoted to the properties developed for wood, metals (primarily aluminum) and fiberglass. Special emphasis is placed on the fiberglass discussion because this material is current the material of choice for wind turbine blades. The paper focuses on the data developed in the U.S., but cites European references that provide important insights.

  6. Thermal properties of graphene and nanostructured carbon materials

    Science.gov (United States)

    Balandin, Alexander A.

    2011-08-01

    Recent years have seen a rapid growth of interest by the scientific and engineering communities in the thermal properties of materials. Heat removal has become a crucial issue for continuing progress in the electronic industry, and thermal conduction in low-dimensional structures has revealed truly intriguing features. Carbon allotropes and their derivatives occupy a unique place in terms of their ability to conduct heat. The room-temperature thermal conductivity of carbon materials span an extraordinary large range -- of over five orders of magnitude -- from the lowest in amorphous carbons to the highest in graphene and carbon nanotubes. Here, I review the thermal properties of carbon materials focusing on recent results for graphene, carbon nanotubes and nanostructured carbon materials with different degrees of disorder. Special attention is given to the unusual size dependence of heat conduction in two-dimensional crystals and, specifically, in graphene. I also describe the prospects of applications of graphene and carbon materials for thermal management of electronics.

  7. Thermal modeling of wide bandgap materials for power MOSFETs

    Science.gov (United States)

    Manandhar, Mahesh B.; Matin, Mohammad A.

    2016-09-01

    This paper investigates the thermal performance of different wide bandgap (WBG) materials for their applicability as semiconductor material in power electronic devices. In particular, Silicon Carbide (SiC) and Gallium Nitride (GaN) are modeled for this purpose. These WBG materials have been known to show superior intrinsic material properties as compared to Silicon (Si), such as higher carrier mobility, lower electrical and thermal resistance. These unique properties have allowed for them to be used in power devices that can operate at higher voltages, temperatures and switching speeds with higher efficiencies. Digital prototyping of power devices have facilitated inexpensive and flexible methods for faster device development. The commercial simulation software COMSOL Multiphysics was used to simulate a 2-D model of MOSFETs of these WBG materials to observe their thermal performance under different voltage and current operating conditions. COMSOL is a simulation software that can be used to simulate temperature changes due to Joule heating in the case of power MOSFETs. COMSOL uses Finite Element/Volume Analysis methods to solve for variables in complex geometries where multiple material properties and physics are involved. The Semiconductor and Heat Transfer with Solids modules of COMSOL were used to study the thermal performance of the MOSFETs in steady state conditions. The results of the simulations for each of the two WBG materials were compared with that of Silicon to determine relative stability and merit of each material.

  8. Quantitative measurement of nanomechanical properties in composite materials

    Science.gov (United States)

    Zhao, Wei

    results significantly, and new, power-law body of revolution models of the probe tip geometry have been applied. Due to the low yield strength of polymers compared with other engineering materials, elastic-plastic contact is considered to better represent the epoxy surface response and was used to acquire more accurate quantitative measurements. Visco-elastic contact response was introduced in the boundary condition of the AFAM cantilever vibration model, due to the creep nature of epoxy, to determine time-dependent effects. These methods have direct impact on the quantitative measurement capabilities of near-filler interphase regions in polymers and composites and the long-term influence of environmental conditions on composites. In addition, quantitative AFAM scans were made on distal surfaces of human bicuspids and molars, to determine the microstructural and spatial variation in nanomechanical properties of the enamel biocomposite. Single point AFAM measurements were performed on individual enamel prism and sheath locations to determine spatial elastic modulus. Mechanical property variation of enamel is associated to the differences in the mineral to organic content and the apatite crystal orientations within the enamel microstructure. Also, variation in the elastic modulus of the enamel ultrastructure was observed in measurements at the outer enamel versus near the dentine enamel junction (DEJ).

  9. Application of the concrete aging model to the case of cracked materials and to the coupling with the mechanical properties; Application du modele de degradation du beton au cas des milieux fissures et au couplage avec la mecanique

    Energy Technology Data Exchange (ETDEWEB)

    Torrenti, J.M.; Adenot, F.; Tognazzi, C. [CEA/Saclay, 91 - Gif-sur-Yvette (France); Tognazzi, C. [Toulouse Univ., 31 (France). LMDC; Danese, S. [Ecole Nationale Superieure des Arts et Industries de Strasbourg, 67 - Strasbourg (France); Poyet, S. [Ecole Nationale Superieure de Cachan, 94 (France)

    1998-07-01

    Predicting the long-term behavior of concrete used in radioactive waste disposal requires the knowledge of the effects of constantly renewed water on its chemistry and its coupling with the mechanical properties. In contact with water, concrete undergoes chemical degradation. This degradation influences the mechanical performance of the material as well as cracks could interfere with the chemical degradation. This paper shows how these problems can be treated using the Ca{sup ++} concentration in pore solution as the state variable that conducts the evolution of chemical, physical and mechanical properties. Some comparisons with experimental results are shown. Finally, the problem of the numerical simulation of accelerated tests of cracked samples is discussed. (authors)

  10. Dynamic material properties of the pregnant human uterus.

    Science.gov (United States)

    Manoogian, Sarah J; Bisplinghoff, Jill A; Kemper, Andrew R; Duma, Stefan M

    2012-06-01

    Given that automobile crashes are the largest single cause of death for pregnant females, scientists are developing advanced computer models of pregnant occupants. The purpose of this study is to quantify the dynamic material properties of the human uterus in order to increase the biofidelity of these models. A total of 19 dynamic tension tests were performed on pregnant human uterus tissues taken from six separate donors. The tissues were collected during full term Cesarean style deliveries and tested within 36 h of surgery. The tissues were processed into uniform coupon sections and tested at 1.5 strains/s using linear motors. Local stress and strain were determined from load data and optical markers using high speed video. The experiments resulted in a non-linear stress versus strain curves with an overall average peak failure true strain of 0.32±0.112 and a corresponding peak failure true stress of 656.3±483.9 kPa. These are the first data available for the dynamic response of pregnant human uterus tissues, and it is anticipated they will increase the accuracy of future pregnant female computational models.

  11. Analysis of nonlinear optical properties in donor–acceptor materials

    Energy Technology Data Exchange (ETDEWEB)

    Day, Paul N. [Air Force Research Laboratory, Wright-Patterson Air Force Base, Ohio 45433 (United States); General Dynamics Information Technology, Inc., Dayton, Ohio 45431 (United States); Pachter, Ruth [Air Force Research Laboratory, Wright-Patterson Air Force Base, Ohio 45433 (United States); Nguyen, Kiet A. [Air Force Research Laboratory, Wright-Patterson Air Force Base, Ohio 45433 (United States); UES, Inc., Dayton, Ohio 45432 (United States)

    2014-05-14

    Time-dependent density functional theory has been used to calculate nonlinear optical (NLO) properties, including the first and second hyperpolarizabilities as well as the two-photon absorption cross-section, for the donor-acceptor molecules p-nitroaniline and dimethylamino nitrostilbene, and for respective materials attached to a gold dimer. The CAMB3LYP, B3LYP, PBE0, and PBE exchange-correlation functionals all had fair but variable performance when compared to higher-level theory and to experiment. The CAMB3LYP functional had the best performance on these compounds of the functionals tested. However, our comprehensive analysis has shown that quantitative prediction of hyperpolarizabilities is still a challenge, hampered by inadequate functionals, basis sets, and solvation models, requiring further experimental characterization. Attachment of the Au{sub 2}S group to molecules already known for their relatively large NLO properties was found to further enhance the response. While our calculations show a modest enhancement for the first hyperpolarizability, the enhancement of the second hyperpolarizability is predicted to be more than an order of magnitude.

  12. Integrated modelling in materials and process technology

    DEFF Research Database (Denmark)

    Hattel, Jesper Henri

    2008-01-01

    Integrated modelling of entire process sequences and the subsequent in-service conditions, and multiphysics modelling of the single process steps are areas that increasingly support optimisation of manufactured parts. In the present paper, three different examples of modelling manufacturing...... processes from the viewpoint of combined materials and process modelling are presented: solidification of thin walled ductile cast iron, integrated modelling of spray forming and multiphysics modelling of friction stir welding. The fourth example describes integrated modelling applied to a failure analysis...

  13. Properties of structural materials in liquid metal environment. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Borgstedt, H.U. [ed.

    1991-12-15

    The International Working Group on Fast Reactors (IWGFR) Specialists Meeting on Properties of Structural Materials in Liquid Metal Environment was held during June 18 to June 20, 1991, at the Nuclear Research Centre (Kernforschungszentrum) in Karlsruhe, Germany. The Specialists Meeting was divided into five technical sessions which addressed topics as follows: Creep-Rupture Behaviour of Structural Materials in Liquid Metal Environment; Behaviour of Materials in Liquid Metal Environments under Off-Normal Conditions;Fatigue and Creep-Fatigue of Structural Materials in Liquid Metal Environment; Crack Propagation in Liquid Sodium; and Conclusions and recommendations. Individual papers have been cataloged separately.

  14. MPOD: A Material Property Open Database linked to structural information

    Science.gov (United States)

    Pepponi, Giancarlo; Gražulis, Saulius; Chateigner, Daniel

    2012-08-01

    Inspired by the Crystallography Open Database (COD), the Material Properties Open Database (MPOD) was given birth. MPOD aims at collecting and making publicly available at no charge tensorial properties (including scalar properties) of phases and linking such properties to structural information of the COD when available. MPOD files are written with the STAR file syntax, used and developed for the Crystallographic Information Files. A dictionary containing new definitions has been written according to the Dictionary Definition Language 1, although some tricks were adopted to allow for multiple entries still avoiding ambiguousness. The initial set includes mechanical properties, elastic stiffness and compliance, internal friction; electrical properties, resistivity, dielectric permittivity and stiffness, thermodynamic properties, heat capacity, thermal conductivity, diffusivity and expansion; electromechanical properties, piezoelectricity, electrostriction, electromechanical coupling; optical properties; piezooptic and photoelastic properties; superconducting properties, critical fields, penetration and coherence lengths. Properties are reported in MPOD files where the original published paper containing the data is cited and structural and experimental information is also given. One MPOD file contains information relative to only one publication and one phase. The files and the information contained therein can also be consulted on-line at http://www.materialproperties.org.

  15. Modelling dielectric and magnetic properties of ferroconcrete

    Directory of Open Access Journals (Sweden)

    T. Frenzel

    2008-05-01

    Full Text Available This contribution discusses the modelling and parameterization of dielectric and magnetic properties of ferroconcrete by using numerical electromagnetic field analysis software. The software is based on the Method of Moments (MoM. The shielding effectiveness (SE of the ferroconcrete DUT was already measured in a study by order of the government. According to these results, the ferroconcrete DUT is modelled and calculated. Therefore the DUT is subdivided into two parts. The first part represents the reinforcement mesh; the second part represents the lossy concrete with complex permittivity. Afterwards, the reflection and transmission properties of numerical analysed building materials are validated and compared with the measurement results in a frequency range of 30–1000 MHz.

  16. Modeling growth in biological materials

    OpenAIRE

    Jones, Gareth Wyn; Chapman, S. Jonathan

    2012-01-01

    The biomechanical modeling of growing tissues has recently become an area of intense interest. In particular, the interplay between growth patterns and mechanical stress is of great importance, with possible applications to arterial mechanics, embryo morphogenesis, tumor development, and bone remodeling. This review aims to give an overview of the theories that have been used to model these phenomena, categorized according to whether the tissue is considered as a continuum object or a collect...

  17. Properties and interfacial microstructure of cement-based materials with composite micro-grains

    Institute of Scientific and Technical Information of China (English)

    FENG Qi; BA Heng-jing; LIU Jun-zhe

    2005-01-01

    Silica fume, fly ash and nano-fiber mineral materials (NR powder) are employed to incorporate into cement-based materials. According to the grain grading mathematical model of cement-based materials, two packing systems, namely, spherical grading system and nano-fiber reinforced system were designed. Properties and interfacial microstructure of the two systems were studied according to secondary interface theory. It was shown that nano-fiber mineral materials can improve the grain grading of the admixture, increase the density of the system, improve the microstructure of the interface and the hardened paste, and enhance the uniformity of cement-based materials mixed with composite micro-grains and greatly increase their wearable rigidity and flexure strength. In this paper, two kinds of interface models, including spherical grain model and nano-fiber reinforced interface model of the cement-based materials mixed with composite micro-grains, were brought forward.

  18. Modeling charge transport in organic photovoltaic materials.

    Science.gov (United States)

    Nelson, Jenny; Kwiatkowski, Joe J; Kirkpatrick, James; Frost, Jarvist M

    2009-11-17

    The performance of an organic photovoltaic cell depends critically on the mobility of charge carriers within the constituent molecular semiconductor materials. However, a complex combination of phenomena that span a range of length and time scales control charge transport in disordered organic semiconductors. As a result, it is difficult to rationalize charge transport properties in terms of material parameters. Until now, efforts to improve charge mobilities in molecular semiconductors have proceeded largely by trial and error rather than through systematic design. However, recent developments have enabled the first predictive simulation studies of charge transport in disordered organic semiconductors. This Account describes a set of computational methods, specifically molecular modeling methods, to simulate molecular packing, quantum chemical calculations of charge transfer rates, and Monte Carlo simulations of charge transport. Using case studies, we show how this combination of methods can reproduce experimental mobilities with few or no fitting parameters. Although currently applied to material systems of high symmetry or well-defined structure, further developments of this approach could address more complex systems such anisotropic or multicomponent solids and conjugated polymers. Even with an approximate treatment of packing disorder, these computational methods simulate experimental mobilities within an order of magnitude at high electric fields. We can both reproduce the relative values of electron and hole mobility in a conjugated small molecule and rationalize those values based on the symmetry of frontier orbitals. Using fully atomistic molecular dynamics simulations of molecular packing, we can quantitatively replicate vertical charge transport along stacks of discotic liquid crystals which vary only in the structure of their side chains. We can reproduce the trends in mobility with molecular weight for self-organizing polymers using a cheap, coarse

  19. Advancing Material Models for Automotive Forming Simulations

    Science.gov (United States)

    Vegter, H.; An, Y.; ten Horn, C. H. L. J.; Atzema, E. H.; Roelofsen, M. E.

    2005-08-01

    Simulations in automotive industry need more advanced material models to achieve highly reliable forming and springback predictions. Conventional material models implemented in the FEM-simulation models are not capable to describe the plastic material behaviour during monotonic strain paths with sufficient accuracy. Recently, ESI and Corus co-operate on the implementation of an advanced material model in the FEM-code PAMSTAMP 2G. This applies to the strain hardening model, the influence of strain rate, and the description of the yield locus in these models. A subsequent challenge is the description of the material after a change of strain path. The use of advanced high strength steels in the automotive industry requires a description of plastic material behaviour of multiphase steels. The simplest variant is dual phase steel consisting of a ferritic and a martensitic phase. Multiphase materials also contain a bainitic phase in addition to the ferritic and martensitic phase. More physical descriptions of strain hardening than simple fitted Ludwik/Nadai curves are necessary. Methods to predict plastic behaviour of single-phase materials use a simple dislocation interaction model based on the formed cells structures only. At Corus, a new method is proposed to predict plastic behaviour of multiphase materials have to take hard phases into account, which deform less easily. The resulting deformation gradients create geometrically necessary dislocations. Additional micro-structural information such as morphology and size of hard phase particles or grains is necessary to derive the strain hardening models for this type of materials. Measurements available from the Numisheet benchmarks allow these models to be validated. At Corus, additional measured values are available from cross-die tests. This laboratory test can attain critical deformations by large variations in blank size and processing conditions. The tests are a powerful tool in optimising forming simulations

  20. 粘弹性阻尼材料动态力学性能温度谱模型%Temperature Spectrum Model of Dynamic Mechanical Properties for Viscoelastic Damping Materials

    Institute of Scientific and Technical Information of China (English)

    张针粒; 李世其; 朱文革

    2011-01-01

    粘弹性阻尼材料的动态力学性能通常以时温叠加得到的频率谱主曲线表征,而时温叠加过程需要测量多个温度下的频率谱,难以保证试验条件的一致性.为此,由时温叠加原理,提出频率谱—温度谱镜像关系的数学形式.基于频率谱五参数分数微分模型,提出粘弹性阻尼材料的动态力学性能温度谱六参数分数微分模型,简称温度谱模型.所提模型能直接利用动态机械分析的试验结果,对于损耗模量和损因子具有对称性或非对称性的情形均适用.温度谱模型的参数具有明确的物理含义,推导温度谱模型参数的初值公式,并给出参数辨识步骤.不同材料在不同测试条件下的动态机械分析试验表明,所提模型可较好地表征粘弹性阻尼材料动态力学性能随温度的变化.%The dynamic mechanical properties of viscoelastic damping materials are usually represented by the master curve (MC) in the frequency domain. In order to construct a MC, multiple frequency spectrums must be tested, in which case it's difficult to maintain the same test conditions. A mathematical form of the mirror relationship between the temperature spectrum and frequency spectrum is suggested according to the time-temperature superposition principle. Based on the five-parameter fractional derivative frequency spectrum model, a six-parameter fractional derivative temperature spectrum model of dynamic mechanical properties, temperature spectrum model for short, is established for viscoelastic damping materials. The proposed model can directly use the results of dynamic mechanical analysis (DMA), and is applicable whether the loss modulus and loss factor are symmetrical or asymmetrical. The six parameters in the model all have clear physical meanings, and some formulas are derived to obtain their initial values, which can be refined by the suggested parameter identification procedure. DMA tests using different materials under

  1. Polyvinyl siloxane impression materials: a review of properties and techniques.

    Science.gov (United States)

    Chee, W W; Donovan, T E

    1992-11-01

    Polyvinyl siloxane impression materials have been shown to have excellent properties as impression materials; however, they are sensitive to manipulative variables. Several methods of using very high viscosity (putty) materials to form "trays" to obtain uniform bulk of the wash impression are described, and the disadvantages of each of these techniques is pointed out. It is recommended that for best results acrylic resin custom trays should be used routinely. The interaction of polyvinyl siloxane materials with latex products is also discussed and problems that this inhibition can cause are stated. Suggestions to avoid this interaction are outlined. One of the disadvantages of the impression materials is that it has a relatively short working time. Refrigerating the material will increase working time without affecting accuracy.

  2. Interatomic Potential Models for Ionic Materials

    Science.gov (United States)

    Gale, Julian D.

    Ionic materials are present in many key technological applications of the modern era, from solid state batteries and fuel cells, nuclear waste immobiliza tion, through to industrial heterogeneous catalysis, such as that found in automotive exhaust systems. With the boundless possibilities for their utilization, it is natural that there has been a long history of computer simulation of their structure and properties in order to understand the materials science of these systems at the atomic level.

  3. Standard Guide for Identification of Fibers, Fillers, and Core Materials in Computerized Material Property Databases

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1992-01-01

    1.1 This guide establishes the essential and desirable elements of data required for the identification in computerized material property databases of fibers, fillers, and core materials used in composite materials. A recommended format for entry of these fields into a computerized database is provided. Examples of the application of this guide are also included. 1.2 The recommended format described in this guide is suggested for use in recording data in a database, which is different from contractural reporting of actual test results. The latter type of information is described in materials specifications shown in business transactions and is subject to agreement between vendor and purchaser. 1.3 The materials covered by this guide include fibers, both continuous and discontinuous, and fillers of various geometries which are used as reinforcements in composite materials, as well as core materials used in sandwich composites. Cores may be foam, honeycomb, or naturally occurring materials such as balsa wood....

  4. Frequency-dependent dynamic effective properties of porous materials

    Institute of Scientific and Technical Information of China (English)

    Peijun Wei; Zhuping Huang

    2005-01-01

    The frequency-dependent dynamic effective properties (phase velocity, attenuation and elastic modulus) of porous materials are studied numerically. The coherent plane longitudinal and shear wave equations, which are obtained by averaging on the multiple scattering fields, are used to evaluate the frequency-dependent dynamic effective properties of a porous material. It is found that the prediction of the dynamic effective properties includes the size effects of voids which are not included in most prediction of the traditional static effective properties. The prediction of the dynamic effective elastic modulus at a relatively low frequency range is compared with that of the traditional static effective elastic modulus, and the dynamic effective elastic modulus is found to be very close to the Hashin-Shtrikman upper bound.

  5. Modeling short-pulse laser excitation of dielectric materials

    DEFF Research Database (Denmark)

    Wædegaard, Kristian Juncher; Sandkamm, Ditte Både; Haahr-Lillevang, Lasse

    2014-01-01

    A theoretical description of ultrashort-pulse laser excitation of dielectric materials based on strong-field excitation in the Keldysh picture combined with a multiple-rateequation model for the electronic excitation including collisional processes is presented. The model includes light attenuation...... in a self-consistent manner and changing optical properties described in a Drude picture. The model can be used to calculate the electronic excitation as a function of time and depth, and from these quantities the time-dependent optical parameters as well as the ablation depth can be derived....... The simulations provide insight into the excitation and propagation dynamics of short-pulse excitation and show that at increasing fluence the excitation becomes localized near the material surface and gives rise to strongmodifications of the optical properties of the material....

  6. Calibrating the Abaqus Crushable Foam Material Model using UNM Data

    Energy Technology Data Exchange (ETDEWEB)

    Schembri, Philip E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lewis, Matthew W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-02-27

    Triaxial test data from the University of New Mexico and uniaxial test data from W-14 is used to calibrate the Abaqus crushable foam material model to represent the syntactic foam comprised of APO-BMI matrix and carbon microballoons used in the W76. The material model is an elasto-plasticity model in which the yield strength depends on pressure. Both the elastic properties and the yield stress are estimated by fitting a line to the elastic region of each test response. The model parameters are fit to the data (in a non-rigorous way) to provide both a conservative and not-conservative material model. The model is verified to perform as intended by comparing the values of pressure and shear stress at yield, as well as the shear and volumetric stress-strain response, to the test data.

  7. Handbook on dielectric and thermal properties of microwaveable materials

    CERN Document Server

    Komarov, Vyacheslav V

    2012-01-01

    The application of microwave energy for thermal processing of different materials and substances is a rapidly growing trend in modern science and engineering. In fact, optimal design work involving microwaves is impossible without solid knowledge of the properties of these materials. Here s a practical reference that collects essential data on the dielectric and thermal properties of microwaveable materials, saving you countless hours on projects in a wide range of areas, including microwave design and heating, applied electrodynamics, food science, and medical technology. This unique book provides hard-to-find information on complex dielectric permittivity of media at industrial, scientific, and medical frequencies (430 MHz, 915MHz, 2.45GHz, 5.8 GHz, and 24.125GHz). Written by a leading expert in the field, this authoritative book does an exceptional job at presenting critical data on various materials and explaining what their key characteristics are concerning microwaves.

  8. Fabrication, properties, and tritium recovery from solid breeder materials

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, C.E. (Argonne National Lab., IL (USA)); Kondo, T. (Japan Atomic Energy Research Inst., Tokyo (Japan)); Roux, N. (CEA Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France)); Tanaka, S. (Tokyo Univ. (Japan)); Vollath, D. (Kernforschungszentrum Karlsruhe GmbH (Germany, F.R.))

    1991-01-01

    The breeding blanket is a key component of the fusion reactor because it directly involves tritium breeding and energy extraction, both of which are critical to development of fusion power. The lithium ceramics continue to show promise as candidate breeder materials. This promise was recognized by the International Thermonuclear Experimental Reactor (ITER) design team in its selection of ceramics as the first option for the ITER breeder material. Blanket design studies have indicated properties in the candidate materials data base that need further investigation. Current studies are focusing on tritium release behavior at high burnup, changes in thermophysical properties with burnup, compatibility between the ceramic breeder and beryllium multiplier, and phase changes with burnup. Laboratory and in-reactor tests, some as part of an international collaboration for development of ceramic breeder materials, are underway. 133 refs., 1 fig.

  9. Modelling Various Solar Cells Materials Using Lorentzian-Drude Coefficients

    Directory of Open Access Journals (Sweden)

    Sameh Osama Abdellatif

    2016-12-01

    Full Text Available In order to develop an optoelectronic model for simulating different light trapping structures sandwiching the photovoltaic active layer, determining the materials dispersion and absorption properties is a must. The targeted model should be able to simulate the desperation and absorption capabilities of different conductor and semiconductor materials over the entire sun spectrum (200 nm to 1700 nm. Therefore, the Lorentzian-Dude (LD model is chosen due to its simplicity in implementation with the finite difference time domain algorithm chosen for optical modelling. In this paper, various materials are selected to be modelled with the LD model. The proposed algorithm is not only used for modelling material behaviour of various conducting materials published in literature, but is also used for other conducting and semiconducting materials that the original model was not capable of modelling over the entire range of spectrum. Besides that, the suggested algorithm showed a better time performance than those mentioned in literature. Experimental 1D grating structure prototype samples were made to validate the simulation results, showing perfect agreement.

  10. Reflector and Shield Material Properties for Project Prometheus

    Energy Technology Data Exchange (ETDEWEB)

    J. Nash

    2005-11-02

    This letter provides updated reflector and shield preliminary material property information to support reactor design efforts. The information provided herein supersedes the applicable portions of Revision 1 to the Space Power Program Preliminary Reactor Design Basis (Reference (a)). This letter partially answers the request in Reference (b) to provide unirradiated and irradiated material properties for beryllium, beryllium oxide, isotopically enriched boron carbide ({sup 11}B{sub 4}C) and lithium hydride. With the exception of {sup 11}B{sub 4}C, the information is provided in Attachments 1 and 2. At the time of issuance of this document, {sup 11}B{sub 4}C had not been studied.

  11. Synthesis, Properties and Mineralogy of Important Inorganic Materials

    CERN Document Server

    Warner, Terence E

    2010-01-01

    Intended as a textbook for courses involving preparative solid-state chemistry, this book offers clear and detailed descriptions on how to prepare a selection of inorganic materials that exhibit important optical, magnetic and electrical properties, on a laboratory scale. The text covers a wide range of preparative methods and can be read as separate, independent chapters or as a unified coherent body of work. Discussions of various chemical systems reveal how the properties of a material can often be influenced by modifications to the preparative procedure, and vice versa. References to miner

  12. Direct Imaging of Anisotropic Material Properties using Photorefractive Laser Ultrasound

    Energy Technology Data Exchange (ETDEWEB)

    Telschow, Kenneth Louis; Deason, Vance Albert; Schley, Robert Scott; Watson, Scott Marshall

    1999-07-01

    Anisotropic properties of materials can be determined by measuring the propagation of elastic waves in different directions. A laser imaging approach is presented that utilizes the adaptive property of photorefractive materials to produce a real-time measurement of the antisymmetric Lamb or flexural traveling wave mode displacement and phase. Continuous excitation is employed and the data is recorded and displayed in all directions simultaneously at video camera frame rates. Fourier transform of the data produces an image of the wave slowness in all planar directions. The results demonstrate imaging of microstructural isotropy and anisotropy and stress induced ansiotropy in plates.

  13. Direct Imaging of Anisotropic Material Properties using Photorefractive Laser Ultrasound

    Energy Technology Data Exchange (ETDEWEB)

    K.L. Telschow; R.S. Schley; S.M. Watson; V.A. Deason

    1999-06-01

    Anisotropic properties of materials can be determined by measuring the propagation of elastic waves in different directions. A laser imaging approach is presented that utilizes the adaptive property of photorefractive materials to produce a real-time measurement of the antisymmetric Lamb or flexural traveling wave mode displacement and phase. Continuous excitation is employed and the data is recorded and displayed in all directions simultaneously at video camera frame rates. Fourier transform of the data produces an image of the wave slowness in all planar directions. The results demonstrate imaging of microstructural isotropy and anisotropy and stress induced ansiotropy in plates.

  14. INVESTIGATION OF TRIBOLOGICAL PROPERTIES CuSn10 BEARING MATERIAL

    Directory of Open Access Journals (Sweden)

    Bekir Sadık ÜNLÜ

    2005-01-01

    Full Text Available Bronzes which copper based alloys is widely used because of properties physical, thermal and tribological as journal bearing material. This material that has tribological performance good conclusions gives at journal bearings. In this study, CuSn10 bronze that were manufactured journal bearings friction and wear properties has been examined and compared. SAE 1050 steel shaft has been used as counter abrader. Experiments have been carried out 10 N and 20 N loads, 750 and 1500 rpm, dry and lubricated conditions by using radial journal bearing wear test rig. As a results, high friction coefficient and weigh loss have been obtained at dry condition more than lubricated condition.

  15. Polymers for electricity and electronics materials, properties, and applications

    CERN Document Server

    Drobny, Jiri George

    2011-01-01

    The comprehensive, practical book that explores the principles, properties, and applications of electrical polymers The electrical properties of polymers present almost limitless possibilities for industrial research and development, and this book provides an in-depth look at these remarkable molecules. In addition to traditional applications in insulating materials, wires, and cables, electrical polymers are increasingly being used in a range of emerging technologies. Presenting a comprehensive overview of how electrical polymers function and how they can be applied in the elec

  16. Mechanical properties of some polymer materials used for tooth positioners.

    Science.gov (United States)

    Collett, A R; Cook, W D; West, V C

    1994-10-01

    The chemical composition, thermal behaviour and mechanical properties of three tooth positioner materials, Urethane P1 (P1), White Rubber (WR) and Elastocryl (EL) were investigated. Infra-red spectrophotometry indicated the P1 polyurethane material to be of the polyether type, and EL to be a blend of poly(ethyl methacrylate) and poly(methyl methacrylate) while WR appeared to be filled cis-poly (isoprene) (natural rubber). The glass transition temperature (Tg) for EL was determined as approximately 10 degrees C, and for both P1 and WR the Tg was less than -50 degrees C. The stress relaxation behaviour was assessed in compression by measuring the stress variation with time. The results for all three materials conformed to the superelastic theory of rubber elasticity. EL exhibited both a more rapid rate and higher degree of stress relaxation than did P1 and WR. Recovery from deformation was assessed by compressing cylinders for given periods of time and then measuring the level of reduced residual strain of the material with time. All three materials exhibited significant residual strain (epsilon(t)) over 'clinically relevant' time periods, and the reduced residual strain (epsilon(t)/epsilon(O)) following deformation was greater for EL than P1 or WR. There was some indication that the three materials have some permanent set following deformation. It was concluded that, in considering desirable mechanical properties of tooth positioner materials, EL is the least suitable of the three examined, with none of the materials being ideal.

  17. Electron paramagnetic resonance of material properties and processes

    Energy Technology Data Exchange (ETDEWEB)

    Brower, K. L.

    1980-01-01

    This paper demonstrates, primarily for the non-specialist and within the context of new and recent achievements, the diagnostic value of electron paramagnetic resonance (EPR) in the study of material properties and processes. I have selected three EPR studies which demonstrate the elegance and uniqueness of EPR in atomic defect studies and exemplify unusual achievements through the use of new techniques for material measurement and preparation. A brief introduction into the origin, interaction, and detection of unpaired electrons is included.

  18. Thermomechanical Properties of Corundum—Mullite—Zirconia Materials

    Institute of Scientific and Technical Information of China (English)

    ZHONGXiangchong; SUNGengcheng

    1998-01-01

    The mechanical properties at elevated tempera-tures of corundum-mullite materials and the effects of zirconia and titania additions have been investi-gated.The results are correlated with changes in microstructure,Based on the results of these investi-gations ,reaction-sintered corundum-mullite-zirco-nia materials with improved hot strength and ther-mal shock resistance have been developed for refractor-ries usage.

  19. Electrical and optoelectronic properties of two-dimensional materials

    Science.gov (United States)

    Wang, Qiaoming

    Electrical and optoelectronic properties of bulk semiconductor materials have been extensively explored in last century. However, when reduced to one-dimensional and two-dimensional, many semiconductors start to show unique electrical and optoelectronic behaviors. In this dissertation, electrical and optoelectronic properties of one-dimensional (nanowires) and two-dimensional semiconductor materials are investigated by various techniques, including scanning photocurrent microscopy, scanning Kelvin probe microscopy, Raman spectroscopy, photoluminescence, and finite-element simulations. In our work, gate-tunable photocurrent in ZnO nanowires has been observed under optical excitation in the visible regime, which originates from the nanowire/substrate interface states. This gate tunability in the visible regime can be used to enhance the photon absorption efficiency, and suppress the undesirable visible-light photodetection in ZnO-based solar cells. The power conversion efficiency of CuInSe2/CdS core-shell nanowire solar cells has been investigated. The highest power conversion efficiency per unit area/volume is achieved with core diameter of 50 nm and the thinnest shell thickness. The existence of the optimal geometrical parameters is due to a combined effect of optical resonances and carrier transport/dynamics. Significant current crowding in two-dimensional black phosphorus field-effect transistors has been found, which has been significantly underestimated by the commonly used transmission-line model. This current crowding can lead to Joule heating close to the contacts. New van der Waals metal-semiconductor junctions have been mechanically constructed and systematically studied. The photocurrent on junction area has been demonstrated to originate from the photothermal effect rather than the photovoltaic effect. Our findings suggest that a reasonable control of interface/surface state properties can enable new and beneficial functionalities in nanostructures. We

  20. Computational evaluation of optoelectronic properties for organic/carbon materials.

    Science.gov (United States)

    Shuai, Zhigang; Wang, Dong; Peng, Qian; Geng, Hua

    2014-11-18

    CONSPECTUS: Organic optoelectronic materials are used in a variety of devices, including light-emitting diodes, field-effect transistors, photovoltaics, thermoelectrics, spintronics, and chemico- and biosensors. The processes that determine the intrinsic optoelectronic properties occur either in the photoexcited states or within the electron-pumped charged species, and computations that predict these optical and electrical properties would help researchers design new materials. In this Account, we describe recent advances in related density functional theory (DFT) methods and present case studies that examine the efficiency of light emission, carrier mobility, and thermoelectric figures of merit by calculation of the electron-vibration couplings. First we present a unified vibrational correlation function formalism to evaluate the excited-state radiative decay rate constant kr, the nonradiative decay rate constant knr, the intersystem crossing rate constant kISC, and the optical spectra. The molecular parameters that appear in the formalism, such as the electronic excited-state energy, vibrational modes, and vibronic couplings, require extensive DFT calculations. We used experiments for anthracene at both low and ambient temperatures to benchmark the calculated photophysical parameters. In the framework of Fermi's golden rule, we incorporated the non-adiabatic coupling and the spin-orbit coupling to evaluate the phosphorescence efficiency and emission spectrum. Both of these are in good agreement with experimental results for anthracene and iridium compounds. Band electron scattering and relaxation processes within Boltzmann theory can describe charge transport in two-dimensional carbon materials and closely packed organic solids. For simplicity, we considered only the acoustic phonon scattering as modeled by the deformation potential approximation coupled with extensive DFT calculations for band structures. We then related the carrier mobility to the band

  1. Dielectric Characteristics of Microstructural Changes and Property Evolution in Engineered Materials

    Science.gov (United States)

    Clifford, Jallisa Janet

    quantitatively using BbDS. These materials are typically used in solid oxide fuel cells (SOFC). Results show significant effect of microstructural design on material properties at multiple temperatures (up to 800 °C). In the later part of the thesis, we will focus on microstructural changes of fiber reinforced composite materials due to impact and static loading. The changes in dielectric response can then be linked to the bulk mechanical properties of the material and various damage modes. Observing trends in dielectric response enables us to further determine local mechanisms and distribution of properties throughout the damaged specimens. A 3D X-ray microscope and a digital microscope have been used to visualize these changes in material microstructure and validate experimental observations. The increase in damage observed in the material microstructure can then also be linked to the changes in dielectric response. Results show that BbDS is an extremely useful tool for identifying microstructural changes within a heterogeneous material and particularly useful in relating remaining properties. Dielectric material variables can be used directly in property degradation laws and help develop a framework for future predictive modeling methodologies.

  2. Fatigue modeling of materials with complex microstructures

    DEFF Research Database (Denmark)

    Qing, Hai; Mishnaevsky, Leon

    2011-01-01

    A new approach and method of the analysis of microstructure-lifetime relationships of materials with complex structures is presented. The micromechanical multiscale computational analysis of damage evolution in materials with complex hierarchical microstructures is combined with the phenomenologi......A new approach and method of the analysis of microstructure-lifetime relationships of materials with complex structures is presented. The micromechanical multiscale computational analysis of damage evolution in materials with complex hierarchical microstructures is combined...... with the phenomenological model of fatigue damage growth. As a result, the fatigue lifetime of materials with complex structures can be determined as a function of the parameters of their structures. As an example, the fatigue lifetimes of wood modeled as a cellular material with multilayered, fiber reinforced walls were...

  3. The synthesis and properties of nanoscale ionic materials

    KAUST Repository

    Rodriguez, Robert Salgado

    2010-02-17

    In this article we discuss the effect of constituents on structure, flow, and thermal properties of nanoscale ionic materials (NIMs). NIMs are a new class of nanohybrids consisting of a nanometer-sized core, a charged corona covalently attached to the core, and an oppositely charged canopy. The hybrid nature of NIMs allows for their properties to be engineered by selectively varying their components. The unique properties associated with these systems can help overcome some of the issues facing the implementation of nanohybrids to various commercial applications, including carbon dioxide capture,water desalinization and as lubricants. Copyright © 2010 John Wiley & Sons, Ltd.

  4. Moisture storage parameters of porous building materials as time-dependent properties

    Science.gov (United States)

    Záleská, Martina; Pavlíková, Milena; Pavlík, Zbyšek

    2016-06-01

    Three different types of bricks and two different types of sandstones are studied in terms of measurement moisture storage parameters for over-hygroscopic moisture area using pressure plate device. For researched materials, basic physical properties as bulk density, matrix density and total open porosity are determined. From the obtained data of moisture storage measurement, the water retention curves and curves of degree of saturation in dependence on suction pressure are constructed. Water retention curve (also called suction curve, capillary potential curve, capillary-pressure function and capillary-moisture relationship) is the basic material property used in models for simulation of moisture storage in porous building materials.

  5. Effect of interface structure on mechanical properties of advanced composite materials.

    Science.gov (United States)

    Gan, Yong X

    2009-11-25

    This paper deals with the effect of interface structures on the mechanical properties of fiber reinforced composite materials. First, the background of research, development and applications on hybrid composite materials is introduced. Second, metal/polymer composite bonded structures are discussed. Then, the rationale is given for nanostructuring the interface in composite materials and structures by introducing nanoscale features such as nanopores and nanofibers. The effects of modifying matrices and nano-architecturing interfaces on the mechanical properties of nanocomposite materials are examined. A nonlinear damage model for characterizing the deformation behavior of polymeric nanocomposites is presented and the application of this model to carbon nanotube-reinforced and reactive graphite nanotube-reinforced epoxy composite materials is shown.

  6. Multi-scale modeling in microstructure evolution of materials

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Intelligent design and control of the microstructure to tailor properties of materials is the dream that materials scientists have been worked hard for many years. Formation of research area of computational materials science paves the way to realize the dream. Simulation of microstructure evolution is a chief branch of the computational materials science and has caused great attention from materials researchers. Multi-scale modeling gets popular just within 5- 6 years recently due to huge research works to try to shorten the distance between simulation and application. People have to command one or more classical simulation methods in order to do the multi-scale modeling so chief simulation methods will be discussed first and then more reviews in detail are given to the phase field simulation. The main part of the paper is carried out to introduce two key approaches to do the multi-scale modeling job. It is suggested that extension of the multiscale modeling is necessary to study the technologies to link microstructure simulation, processing simulation and property simulation each other as well as to build bridges between different simulation methods and between analytical models and numerical models.

  7. Evaluation of Water Resistance and Diffusion Properties of Paint Materials

    Directory of Open Access Journals (Sweden)

    J. Drchalová

    2001-01-01

    Full Text Available A simple method is presented for evaluating the water-proofness quality of paints on lining materials. The method is based on measuring the integral capillarity in dependence on time, and then comparing this value to the value determined for the basic lining material. Measurements of the effective water vapor permeability then provide information on the risk of condensation which may increase after applying the paint. A practical application of the method is performed with four Karlocolor paints on glass concrete substrates. All the Karlocolor paints are found to be very effective materials for driven rain protection. The diffusion properties of all the paints are found to be excellent.

  8. Percolation modeling of self-damaging of composite materials

    Science.gov (United States)

    Domanskyi, Sergii; Privman, Vladimir

    2014-07-01

    We propose the concept of autonomous self-damaging in “smart” composite materials, controlled by activation of added nanosize “damaging” capsules. Percolation-type modeling approach earlier applied to the related concept of self-healing materials, is used to investigate the behavior of the initial material's fatigue. We aim at achieving a relatively sharp drop in the material's integrity after some initial limited fatigue develops in the course of the sample's usage. Our theoretical study considers a two-dimensional lattice model and involves Monte Carlo simulations of the connectivity and conductance in the high-connectivity regime of percolation. We give several examples of local capsule-lattice and capsule-capsule activation rules and show that the desired self-damaging property can only be obtained with rather sophisticated “smart” material's response involving not just damaging but also healing capsules.

  9. Research of properties of modern heat-insulation materials

    Directory of Open Access Journals (Sweden)

    A. S. Shcherbak

    2013-04-01

    Full Text Available Purpose. To study the modern heat-insulating materials presented at the market of Ukraine and to estimate the efficiency of their application. Methodology. Research and analysis of heat-insulating materials presented at the market of Ukraine, according to the existing standards. Findings. To ensure the energy efficiency in buildings and constructions it is necessary to apply the domestic heat-insulating material, which possesses the given thermo technical characteristics, reduced indexes of water absorption, flammability and toxicity, as well as durability and relatively low self–cost. Originality. Basic heat-insulating materials, which are most widely used in construction are systematized, the researches of their properties are conducted and the foam glass is chosen as the most effective heat-insulating material. It is characterized by high thermo technical characteristics and possesses the best ecological indexes, as well as the sturdiness for aggressive factors influence. Practical value. Special attention deserves the insulating material foam glass, which is a synthetic silicate material with evenly placed pores (0.1 ... 5.0 mm separated by thin septa with a vitreous substance possesses the necessary properties and by aforesaid may be accepted for studies aimed its improvement (modification. The results of researches can be applied in the foam glass production, which is used for heat-insulation of buildings and constructions, equipment, pipelines etc.

  10. Characterization of electrical and optical properties of silicon based materials

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Guobin

    2009-12-04

    In this work, the electrical and luminescence properties of a series of silicon based materials used for photovoltaics, microelectronics and nanoelectronics have been investigated by means of electron beam induced current (EBIC), cathodoluminescence (CL), photoluminescence (PL) and electroluminescence (EL) methods. Photovoltaic materials produced by block casting have been investigated by EBIC on wafers sliced from different parts of the ingot. Various solar cell processings have been compared in parallel wafers by means of EBIC collection efficiency measurements and contrast-temperature C(T) behaviors of the extended defects, i. e. dislocations and grain boundaries (GBs). It was found that the solar cell processing with phosphorus diffusion gettering (PDG) followed with a SiN firing greatly reduces the recombination activity of extended defects at room temperature, and improves the bulk property simultaneously. A remaining activity of the dislocations indicates the limitation of the PDG at extended defects. Abnormal behavior of the dislocation activity after certain solar cell processes was also observed in the region with high dislocation density, the dislocations are activated after certain solar cell processings. In order to evaluate the properties of a thin polycrystalline silicon layer prepared by Al-induced layer exchange (Alile) technique, epitaxially layer grown on silicon substrate with different orientations was used as a model system to investigate the impact by the process temperature and the substrates. EBIC energy dependent collection efficiency measurements reveal an improvement of the epilayer quality with increasing substrate temperature during the growth from 450 C to 650 C, and a decrease of epilayer quality at 700 C. PL measurements on the epitaxially grown Si layer on silicon substrates revealed no characteristic dislocation-related luminescence (DRL) lines at room temperature and 77 K, while in the samples prepared by Alile process, intense

  11. Mechanics of advanced materials analysis of properties and performance

    CERN Document Server

    Matveenko, Valery

    2015-01-01

    The last decades have seen a large extension of types of materials employed in various applications. In many cases these materials demonstrate mechanical properties and performance that vary significantly from those of their traditional counterparts. Such uniqueness is sought – or even specially manufactured – to meet increased requirements on modern components and structures related to their specific use. As a result, mechanical behaviors of these materials under different loading and environmental conditions are outside the boundaries of traditional mechanics of materials, presupposing development of new characterization techniques, theoretical descriptions and numerical tools. The book presents interesting examples of recent developments in this area. Among the studied materials are bulk metallic glasses, metamaterials, special composites, piezoelectric smart structures, nonwovens, etc.

  12. Comparison of shrinkage related properties of various patch repair materials

    Science.gov (United States)

    Kristiawan, S. A.; Fitrianto, R. S.

    2017-02-01

    A patch repair material has been developed in the form of unsaturated polyester resin (UPR)-mortar. The performance and durability of this material are governed by its compatibility with the concrete being repaired. One of the compatibility issue that should be tackled is the dimensional compatibility as a result of differential shrinkage between the repair material and the concrete substrate. This research aims to evaluate such shrinkage related properties of UPR-mortar and to compare with those of other patch repair materials. The investigation includes the following aspects: free shrinkage, resistance to delamination and cracking. The results indicate that UPR-mortar poses a lower free shrinkage, lower risk of both delamination and cracking tendency in comparison to other repair materials.

  13. Mechanical properties of materials at micro/nano scales

    Science.gov (United States)

    Xu, Wei-Hua

    Mechanical properties of materials in small dimensions, including the depth-dependent hardness at the nano/micrometer scales, and the mechanical characterization of thin films and nanotubes, are reported. The surface effect on the depth-dependent nano/microhardness was studied and an apparent surface stress was introduced to represent the energy dissipated per unit area of a solid surface. A plastic bearing ratio model was proposed for the nanoindentation of rough surfaces. The energy dissipation occurring at the indented surface is among the factors that cause the Indentation Size Effect (ISE) at the micro/nanometer scales. Furthermore, an elastic-plastic bearing ratio model was developed for nanoindentation of rough surfaces with a flat indenter tip. The theoretical predictions agree with the experimental results and finite element simulations, from which the elastic constant and the surface hardness were extracted. The surface hardness exhibits an inverse ISE due to the interaction of asperities. The nanoindentation tests on Highly Oriented Pyrolytic Graphite (HOPG) may lead to the formation of carbon tubes, which are rolled up by the delaminated graphite layers. The nanoindentation loading-unloading curves reveal single pop-in and multiple pop-in phenomena, which is induced by fracture of the graphite layers and/or by delamination between the layers. From the load at pop-in, the fracture strength of the layers and/or the bonding strength between the layers can be estimated by the elastic field model for Hertzian contact including sliding friction for transverse isotropy. Two novel methods were developed to estimate the mechanical properties of films, including the Raman spectra method for the estimation of residual stresses in thin ferroelectric films and the microbridge testing method for the mechanical characterization of trilayer thin films. Mechanical characterization was also carried out on Tobacco Mosaic Virus (TMV) nanotubes with each being comprised of

  14. A Statistics-Based Material Property Analysis to Support TPS Characterization

    Science.gov (United States)

    Copeland, Sean R.; Cozmuta, Ioana; Alonso, Juan J.

    2012-01-01

    Accurate characterization of entry capsule heat shield material properties is a critical component in modeling and simulating Thermal Protection System (TPS) response in a prescribed aerothermal environment. The thermal decomposition of the TPS material during the pyrolysis and charring processes is poorly characterized and typically results in large uncertainties in material properties as inputs for ablation models. These material property uncertainties contribute to large design margins on flight systems and cloud re- construction efforts for data collected during flight and ground testing, making revision to existing models for entry systems more challenging. The analysis presented in this work quantifies how material property uncertainties propagate through an ablation model and guides an experimental test regimen aimed at reducing these uncertainties and characterizing the dependencies between properties in the virgin and charred states for a Phenolic Impregnated Carbon Ablator (PICA) based TPS. A sensitivity analysis identifies how the high-fidelity model behaves in the expected flight environment, while a Monte Carlo based uncertainty propagation strategy is used to quantify the expected spread in the in-depth temperature response of the TPS. An examination of how perturbations to the input probability density functions affect output temperature statistics is accomplished using a Kriging response surface of the high-fidelity model. Simulations are based on capsule configuration and aerothermal environments expected during the Mars Science Laboratory (MSL) entry sequence. We identify and rank primary sources of uncertainty from material properties in a flight-relevant environment, show the dependence on spatial orientation and in-depth location on those uncertainty contributors, and quantify how sensitive the expected results are.

  15. Transport Properties for Combustion Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Brown, N.J.; Bastein, L.; Price, P.N.

    2010-02-19

    This review examines current approximations and approaches that underlie the evaluation of transport properties for combustion modeling applications. Discussed in the review are: the intermolecular potential and its descriptive molecular parameters; various approaches to evaluating collision integrals; supporting data required for the evaluation of transport properties; commonly used computer programs for predicting transport properties; the quality of experimental measurements and their importance for validating or rejecting approximations to property estimation; the interpretation of corresponding states; combination rules that yield pair molecular potential parameters for unlike species from like species parameters; and mixture approximations. The insensitivity of transport properties to intermolecular forces is noted, especially the non-uniqueness of the supporting potential parameters. Viscosity experiments of pure substances and binary mixtures measured post 1970 are used to evaluate a number of approximations; the intermediate temperature range 1 < T* < 10, where T* is kT/{var_epsilon}, is emphasized since this is where rich data sets are available. When suitable potential parameters are used, errors in transport property predictions for pure substances and binary mixtures are less than 5 %, when they are calculated using the approaches of Kee et al.; Mason, Kestin, and Uribe; Paul and Warnatz; or Ern and Giovangigli. Recommendations stemming from the review include (1) revisiting the supporting data required by the various computational approaches, and updating the data sets with accurate potential parameters, dipole moments, and polarizabilities; (2) characterizing the range of parameter space over which the fit to experimental data is good, rather than the current practice of reporting only the parameter set that best fits the data; (3) looking for improved combining rules, since existing rules were found to under-predict the viscosity in most cases; (4

  16. Modeling the triaxial behavior of riverbed and blasted quarried rockfill materials using hardening soil model

    Directory of Open Access Journals (Sweden)

    N.P. Honkanadavar

    2016-06-01

    Full Text Available Riverbed modeled rockfill material from Noa Dehing dam project, Arunachal Pradesh, India and blasted quarried modeled rockfill material from Kol dam project, Himachal Pradesh, India were considered for this research. Riverbed rockfill material is rounded to sub-rounded and quarried rockfill material is angular to sub-angular in shape. Prototype rockfill materials were modeled into maximum particle size (dmax of 4.75 mm, 10 mm, 19 mm, 25 mm, 50 mm and 80 mm for testing in the laboratory. Consolidated drained triaxial tests were conducted on modeled rockfill materials with a specimen size of 381 mm in diameter and 813 mm in height to study the stress–strain–volume change behavior for both rockfill materials. Index properties, i.e. uncompacted void content (UVC and uniaxial compressive strength (UCS, were determined for both rockfill materials in association with material parameters. An elastoplastic hardening soil (HS constitutive model was used to predict the behavior of modeled rockfill materials. Comparing the predicted and observed stress–strain–volume change behavior, it is found that both observed and predicted behaviors match closely. The procedures were developed to predict the shear strength and elastic parameters of rockfill materials using the index properties, i.e. UCS, UVC and relative density (RD, and predictions were made satisfactorily. Comparing the predicted and experimentally determined shear strengths and elastic parameters, it is observed that both values match closely. Then these procedures were used to predict the elastic and shear strength parameters of large-size prototype rockfill materials. Correlations were also developed between index properties and material strength parameters (dilatancy angle, ψ, and initial void ratio, einit, required for HS model of modeled rockfill materials and the same correlations were used to predict the strength parameters for the prototype rockfill materials. Using the

  17. Modeling the triaxial behavior of riverbed and blasted quarried rockfill materials using hardening soil model

    Institute of Scientific and Technical Information of China (English)

    N.P. Honkanadavar; K.G. Sharma

    2016-01-01

    Riverbed modeled rockfill material from Noa Dehing dam project, Arunachal Pradesh, India and blasted quarried modeled rockfill material from Kol dam project, Himachal Pradesh, India were considered for this research. Riverbed rockfill material is rounded to sub-rounded and quarried rockfill material is angular to sub-angular in shape. Prototype rockfill materials were modeled into maximum particle size (dmax) of 4.75 mm, 10 mm, 19 mm, 25 mm, 50 mm and 80 mm for testing in the laboratory. Consolidated drained triaxial tests were conducted on modeled rockfill materials with a specimen size of 381 mm in diameter and 813 mm in height to study the stressestrainevolume change behavior for both rockfill materials. Index properties, i.e. uncompacted void content (UVC) and uniaxial compressive strength (UCS), were determined for both rockfill materials in association with material parameters. An elasto-plastic hardening soil (HS) constitutive model was used to predict the behavior of modeled rockfill materials. Comparing the predicted and observed stressestrainevolume change behavior, it is found that both observed and predicted behaviors match closely. The procedures were developed to predict the shear strength and elastic parameters of rockfill materials using the index properties, i.e. UCS, UVC and relative density (RD), and predictions were made satisfactorily. Comparing the predicted and experi-mentally determined shear strengths and elastic parameters, it is observed that both values match closely. Then these procedures were used to predict the elastic and shear strength parameters of large-size prototype rockfill materials. Correlations were also developed between index properties and ma-terial strength parameters (dilatancy angle, j, and initial void ratio, einit, required for HS model) of modeled rockfill materials and the same correlations were used to predict the strength parameters for the prototype rockfill materials. Using the predicted material parameters

  18. Modeling the Reactions of Energetic Materials in the Condensed Phase

    Energy Technology Data Exchange (ETDEWEB)

    Fried, L E; Manaa, M R; Lewis, J P

    2003-12-03

    High explosive (HE) materials are unique for having a strong exothermic reactivity, which has made them desirable for both military and commercial applications. Although the history of HE materials is long, condensed-phase properties are poorly understood. Understanding the condensed-phase properties of HE materials is important for determining stability and performance. Information regarding HE material properties (for example, the physical, chemical, and mechanical behaviors of the constituents in plastic-bonded explosive, or PBX, formulations) is necessary in efficiently building the next generation of explosives as the quest for more powerful energetic materials (in terms of energy per volume) moves forward. In addition, understanding the reaction mechanisms has important ramifications in disposing of such materials safely and cheaply, as there exist vast stockpiles of HE materials with corresponding contamination of earth and groundwater at these sites, as well as a military testing sites The ability to model chemical reaction processes in condensed phase energetic materials is rapidly progressing. Chemical equilibrium modeling is a mature technique with some limitations. Progress in this area continues, but is hampered by a lack of knowledge of condensed phase reaction mechanisms and rates. Atomistic modeling is much more computationally intensive, and is currently limited to very short time scales. Nonetheless, this methodology promises to yield the first reliable insights into the condensed phase processes responsible for high explosive detonation. Further work is necessary to extend the timescales involved in atomistic simulations. Recent work in implementing thermostat methods appropriate to shocks may promise to overcome some of these difficulties. Most current work on energetic material reactivity assumes that electronically adiabatic processes dominate. The role of excited states is becoming clearer, however. These states are not accessible in perfect

  19. Food material properties and early hominin processing techniques.

    Science.gov (United States)

    Zink, Katherine D; Lieberman, Daniel E; Lucas, Peter W

    2014-12-01

    Although early Homo is hypothesized to have used tools more than australopiths to process foods prior to consumption, it is unknown how much the food processing techniques they used altered the material properties of foods, and therefore the masticatory forces they generated, and how well they were able to comminute foods. This study presents experimental data on changes to food material properties caused by mechanical tenderization (pounding with a stone tool) and cooking (dry roasting) of two foods likely to have been important components of the hominin diet: meat and tubers. Mechanical tenderization significantly decreased tuber toughness by 42%, but had no effect on meat toughness. Roasting significantly decreased several material properties of tubers correlated with masticatory effort including toughness (49%), fracture stress (28%) and elastic modulus (45%), but increased the toughness (77%), fracture stress (50%-222%), and elastic modulus of muscle fibers in meat (308%). Despite increasing many material properties of meat associated with higher masticatory forces, roasting also decreased measured energy loss by 28%, which likely makes it easier to chew. These results suggest that the use of food processing techniques by early Homo probably differed for meat and tubers, but together would have reduced masticatory effort, helping to relax selection to maintain large, robust faces and large, thickly enameled teeth.

  20. Tailoring material properties of a nanofibrous extracellular matrix derived hydrogel

    Science.gov (United States)

    Johnson, Todd D.; Lin, Stephen Y.; Christman, Karen L.

    2011-12-01

    In the native tissue, the interaction between cells and the extracellular matrix (ECM) is essential for cell migration, proliferation, differentiation, mechanical stability, and signaling. It has been shown that decellularized ECMs can be processed into injectable formulations, thereby allowing for minimally invasive delivery. Upon injection and increase in temperature, these materials self-assemble into porous gels forming a complex network of fibers with nanoscale structure. In this study we aimed to examine and tailor the material properties of a self-assembling ECM hydrogel derived from porcine myocardial tissue, which was developed as a tissue specific injectable scaffold for cardiac tissue engineering. The impact of gelation parameters on ECM hydrogels has not previously been explored. We examined how modulating pH, temperature, ionic strength, and concentration affected the nanoscale architecture, mechanical properties, and gelation kinetics. These material characteristics were assessed using scanning electron microscopy, rheometry, and spectrophotometry, respectively. Since the main component of the myocardial matrix is collagen, many similarities between the ECM hydrogel and collagen gels were observed in terms of the nanofibrous structure and modulation of properties by altering ionic strength. However, variation from collagen gels was noted for the gelation temperature along with varied times and rates of gelation. These discrepancies when compared to collagen are likely due to the presence of other ECM components in the decellularized ECM based hydrogel. These results demonstrate how the material properties of ECM hydrogels could be tailored for future in vitro and in vivo applications.

  1. Thermal properties of hemp fibre non-woven materials

    Science.gov (United States)

    Freivalde, Liga; Kukle, Silvija; Russell, Stephen

    2013-12-01

    This review considers the thermal properties analysis of hemp fiber non-woven materials made by three different manufacturing technologies - thermal bonding, needle-punching and hydro-entanglement. For non-wovens development two hemp fibers cultivars grown in Latvia were used - Purini and Bialobrzeskie. Thermal resistance, conductivity and the effects of several parameters on thermal performance are revised.

  2. I. The metabolic properties of plutonium and allied materials

    Energy Technology Data Exchange (ETDEWEB)

    Hamilton, J.G.

    1948-05-24

    This report on the metabolic properties of plutonium and related radioactive materials presents experimental information in the following areas: radioautographic studies; tracer studies (with tables of accumulation in tissues) of actinium, radio-zirconium, technetium, radio-rubidium, radio-germanium, beryllium, and cadmium; decontamination and bone metabolism studies; and radio-chemical isolation.

  3. Thermal modelling of extrusion based additive manufacturing of composite materials

    DEFF Research Database (Denmark)

    Jensen, Mathias Laustsen; Sonne, Mads Rostgaard; Hattel, Jesper Henri

    2017-01-01

    One of the hottest topics regarding manufacturing these years is additive manufacturing (AM). AM is a young branch of manufacturing techniques, which by nature is disruptive due to its completely different manufacturing approach, wherein material is added instead of removed. By adding material...... process knowledge, and validating the generated toolpaths before the real manufacturing process takes place: Hence removing time consuming and expensive trial-and-error processes for new products. This study applies a 2D restricted finite volume model aimed to describe thermoplastic Acrylonitrille......-butadiene-styrene (ABS) and thermosetting polyurethane (PU) material extrusion processes. During the experimental evaluation of the produced models it is found that some critical material properties needs to be further investigated to increase the precision of the model. It is however also found that even with only...

  4. Material and Flexural Properties of Fiber-reinforced Rubber Concrete

    Science.gov (United States)

    Helminger, Nicholas P.

    The purpose of this research is to determine the material properties of rubber concrete with the addition of fibers, and to determine optimal mixture dosages of rubber and fiber in concrete for structural applications. Fiber-reinforced concrete and rubberized concrete have been researched separately extensively, but this research intends to combine both rubber and fiber in a concrete matrix in order to create a composite material, fiber-reinforced rubber concrete (FRRC). Sustainability has long been important in engineering design, but much of the previous research performed on sustainable concrete does not result in a material that can be used for practical purposes. While still achieving a material that can be used for structural applications, economical considerations were given when choosing the proportions and types of constituents in the concrete mix. Concrete mixtures were designed, placed, and tested in accordance with common procedures and standards, with an emphasis on practicality. Properties that were investigated include compressive strength, tensile strength, modulus of elasticity, toughness, and ductility. The basis for determining the optimal concrete mixture is one that is economical, practical, and exhibits ductile properties with a significant strength. Results show that increasing percentages of rubber tend to decrease workability, unit weight, compressive strength, split tensile strength, and modulus of elasticity while the toughness is increased. The addition of steel needle fibers to rubber concrete increases unit weight, compressive strength, split tensile strength, modulus of elasticity, toughness, and ductility of the composite material.

  5. Experimental analysis of electrical properties of composite materials

    Science.gov (United States)

    Fiala, L.; Rovnaník, P.; Černý, R.

    2017-02-01

    Dry cement-based composites are electrically non-conductive materials that behave in electric field like dielectrics. However, a relatively low amount of electrically conductive admixture significantly increases the electrical conductivity which extends applicability of such materials in practice. Therefore, they can be used as self-monitoring sensors controlling development of cracks; as sensors monitoring moisture content or when treated by an external electrical voltage as heat sources used for deicing of material's surface layer. Alkali-activated aluminosilicates (AAA), as competing materials to cement-based materials, are intensively investigated in the present due to their superior durability and environmental impact. Whereas the electrical properties of AAA are similar to those cement-based, they can be enhanced in the same way. In both cases, it is crucial to find a reasonable amount of electrically conductive phase to design composites with a sufficient electrical conductivity at an affordable price. In this paper, electrical properties of composites based on AAA binder and electrically conductive admixture represented by carbon nanotubes (CNT) are investigated. Measurements of electrical properties are carried out by means of 2-probes DC technique on nine types of samples; reference sample without the conductive phase and samples with CNT admixture in amount of 0.1 % - 2.5 % by vol. A significant increase of the electrical conductivity starts from the amount of 0.5 % CNT admixture and in case of 2.5 % CNT is about three orders of magnitude higher compared to the reference sample.

  6. Hyperelastic Material Properties of Mouse Skin under Compression.

    Directory of Open Access Journals (Sweden)

    Yuxiang Wang

    Full Text Available The skin is a dynamic organ whose complex material properties are capable of withstanding continuous mechanical stress while accommodating insults and organism growth. Moreover, synchronized hair cycles, comprising waves of hair growth, regression and rest, are accompanied by dramatic fluctuations in skin thickness in mice. Whether such structural changes alter skin mechanics is unknown. Mouse models are extensively used to study skin biology and pathophysiology, including aging, UV-induced skin damage and somatosensory signaling. As the skin serves a pivotal role in the transfer function from sensory stimuli to neuronal signaling, we sought to define the mechanical properties of mouse skin over a range of normal physiological states. Skin thickness, stiffness and modulus were quantitatively surveyed in adult, female mice (Mus musculus. These measures were analyzed under uniaxial compression, which is relevant for touch reception and compression injuries, rather than tension, which is typically used to analyze skin mechanics. Compression tests were performed with 105 full-thickness, freshly isolated specimens from the hairy skin of the hind limb. Physiological variables included body weight, hair-cycle stage, maturity level, skin site and individual animal differences. Skin thickness and stiffness were dominated by hair-cycle stage at young (6-10 weeks and intermediate (13-19 weeks adult ages but by body weight in mature mice (26-34 weeks. Interestingly, stiffness varied inversely with thickness so that hyperelastic modulus was consistent across hair-cycle stages and body weights. By contrast, the mechanics of hairy skin differs markedly with anatomical location. In particular, skin containing fascial structures such as nerves and blood vessels showed significantly greater modulus than adjacent sites. Collectively, this systematic survey indicates that, although its structure changes dramatically throughout adult life, mouse skin at a given

  7. Preparation and Properties of Carbon Fiber Chiral Materials

    Institute of Scientific and Technical Information of China (English)

    ZHANG Ping; HUANG Zhixin; WANG Guoqing

    2008-01-01

    The chiral materials were prepared by using the carbon fiber helices as chiral inclusions,and the composite of Fe3O4 and polyaniline as matrix.The electromagnetic properties,including the rotation angles,the axial ratios and the complex chirality parameters,were measured by using a circular waveguide method in the 8.5-11.0 GHz frequency range.The dependence of these electromagnetic properties on the frequency and the concentration of the Fe3O4 in the composite matrix were analyzed.The results show that an appropriate concentration of Fe3O4 in the matrix is useful in improving the electromagnetic properties of the chiral material.

  8. Effects of Material Properties on Bacterial Adhesion and Biofilm Formation.

    Science.gov (United States)

    Song, F; Koo, H; Ren, D

    2015-08-01

    Adhesion of microbes, such as bacteria and fungi, to surfaces and the subsequent formation of biofilms cause multidrug-tolerant infections in humans and fouling of medical devices. To address these challenges, it is important to understand how material properties affect microbe-surface interactions and engineer better nonfouling materials. Here we review the recent progresses in this field and discuss the main challenges and opportunities. In particular, we focus on bacterial biofilms and review the effects of surface energy, charge, topography, and stiffness of substratum material on bacterial adhesion. We summarize how these surface properties influence oral biofilm formation, and we discuss the important findings from nondental systems that have potential applications in dental medicine. © International & American Associations for Dental Research 2015.

  9. Structure-property relationships in silica-siloxane nanocomposite materials

    Energy Technology Data Exchange (ETDEWEB)

    Ulibarri, T.A.; Derzon, D.K.; Wang, L.C.

    1997-03-01

    The simultaneous formation of a filler phase and a polymer matrix via in situ sol-gel techniques provides silica-siloxane nanocomposite materials of high strength. This study concentrates on the effects of temperature and relative humidity on a trimodal polymer system in an attempt to accelerate the reaction as well as evaluate subtle process- structure-property relations. It was found that successful process acceleration is only viable for high humidity systems when using the tin(IV) catalyst dibutyltin dilaurate. Processes involving low humidity were found to be very temperature and time dependent. Bimodal systems were investigated and demonstrated that the presence of a short-chain component led to enhanced material strength. This part of the study also revealed a link between the particle size and population density and the optimization of material properties.

  10. Molecular structure based property modeling: Development/ improvement of property models through a systematic property-data-model analysis

    DEFF Research Database (Denmark)

    Hukkerikar, Amol Shivajirao; Sarup, Bent; Sin, Gürkan;

    2013-01-01

    to a wide range of properties of pure compounds. In this work, however, the application of the method is illustrated for the property modeling of normal melting point, enthalpy of fusion, enthalpy of formation, and critical temperature. For all the properties listed above, it has been possible to achieve......The objective of this work is to develop a method for performing property-data-model analysis so that efficient use of knowledge of properties could be made in the development/improvement of property prediction models. The method includes: (i) analysis of property data and its consistency check......; (ii) selection of the most appropriate form of the property model; (iii) selection of the data-set for performing parameter regression and uncertainty analysis; and (iv) analysis of model prediction errors to take necessary corrective steps to improve the accuracy and the reliability of property...

  11. The Model 9977 Radioactive Material Packaging Primer

    Energy Technology Data Exchange (ETDEWEB)

    Abramczyk, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-10-09

    The Model 9977 Packaging is a single containment drum style radioactive material (RAM) shipping container designed, tested and analyzed to meet the performance requirements of Title 10 the Code of Federal Regulations Part 71. A radioactive material shipping package, in combination with its contents, must perform three functions (please note that the performance criteria specified in the Code of Federal Regulations have alternate limits for normal operations and after accident conditions): Containment, the package must “contain” the radioactive material within it; Shielding, the packaging must limit its users and the public to radiation doses within specified limits; and Subcriticality, the package must maintain its radioactive material as subcritical

  12. MMSNF 2005. Materials models and simulations for nuclear fuels

    Energy Technology Data Exchange (ETDEWEB)

    Freyss, M.; Durinck, J.; Carlot, G.; Sabathier, C.; Martin, P.; Garcia, P.; Ripert, M.; Blanpain, P.; Lippens, M.; Schut, H.; Federov, A.V.; Bakker, K.; Osaka, M.; Miwa, S.; Sato, I.; Tanaka, K.; Kurosaki, K.; Uno, M.; Yamanaka, S.; Govers, K.; Verwerft, M.; Hou, M.; Lemehov, S.E.; Terentyev, D.; Govers, K.; Kotomin, E.A.; Ashley, N.J.; Grimes, R.W.; Van Uffelen, P.; Mastrikov, Y.; Zhukovskii, Y.; Rondinella, V.V.; Kurosaki, K.; Uno, M.; Yamanaka, S.; Minato, K.; Phillpot, S.; Watanabe, T.; Shukla, P.; Sinnott, S.; Nino, J.; Grimes, R.; Staicu, D.; Hiernaut, J.P.; Wiss, T.; Rondinella, V.V.; Ronchi, C.; Yakub, E.; Kaye, M.H.; Morrison, C.; Higgs, J.D.; Akbari, F.; Lewis, B.J.; Thompson, W.T.; Gueneau, C.; Gosse, S.; Chatain, S.; Dumas, J.C.; Sundman, B.; Dupin, N.; Konings, R.; Noel, H.; Veshchunov, M.; Dubourg, R.; Ozrin, C.V.; Veshchunov, M.S.; Welland, M.T.; Blanc, V.; Michel, B.; Ricaud, J.M.; Calabrese, R.; Vettraino, F.; Tverberg, T.; Kissane, M.; Tulenko, J.; Stan, M.; Ramirez, J.C.; Cristea, P.; Rachid, J.; Kotomin, E.; Ciriello, A.; Rondinella, V.V.; Staicu, D.; Wiss, T.; Konings, R.; Somers, J.; Killeen, J

    2006-07-01

    The MMSNF Workshop series aims at stimulating research and discussions on models and simulations of nuclear fuels and coupling the results into fuel performance codes.This edition was focused on materials science and engineering for fuel performance codes. The presentations were grouped in three technical sessions: fundamental modelling of fuel properties; integral fuel performance codes and their validation; collaborations and integration of activities. (A.L.B.)

  13. Visual texture accurate material appearance measurement, representation and modeling

    CERN Document Server

    Haindl, Michal

    2013-01-01

    This book surveys the state of the art in multidimensional, physically-correct visual texture modeling. Features: reviews the entire process of texture synthesis, including material appearance representation, measurement, analysis, compression, modeling, editing, visualization, and perceptual evaluation; explains the derivation of the most common representations of visual texture, discussing their properties, advantages, and limitations; describes a range of techniques for the measurement of visual texture, including BRDF, SVBRDF, BTF and BSSRDF; investigates the visualization of textural info

  14. Millimeter wave and terahertz dielectric properties of biological materials

    Science.gov (United States)

    Khan, Usman Ansar

    Broadband dielectric properties of materials can be employed to identify, detect, and characterize materials through their unique spectral signatures. In this study, millimeter wave, submillimeter wave, and terahertz dielectric properties of biological substances inclusive of liquids, solids, and powders were obtained using Dispersive Fourier Transform Spectroscopy (DFTS). Two broadband polarizing interferometers were constructed to test materials from 60 GHz to 1.2 THz. This is an extremely difficult portion of the frequency spectrum to obtain a material's dielectric properties since neither optical nor microwave-based techniques provide accurate data. The dielectric characteristics of liquids such as cyclohexane, chlorobenzene, benzene, ethanol, methanol, 1,4 dioxane, and 10% formalin were obtained using the liquid interferometer. Subsequently the solid interferometer was utilized to determine the dielectric properties of human breast tissues, which are fixed and preserved in 10% formalin. This joint collaboration with the Tufts New England Medical Center demonstrated a significant difference between the dielectric response of tumorous and non-tumorous breast tissues across the spectrum. Powders such as anthrax, flour, talc, corn starch, dry milk, and baking soda have been involved in a number of security threats and false alarms around the globe in the last decade. To be able to differentiate hoax attacks and serious security threats, the dielectric properties of common household powders were also examined using the solid interferometer to identify the powders' unique resonance peaks. A new sample preparation kit was designed to test the powder specimens. It was anticipated that millimeter wave and terahertz dielectric characterization will enable one to clearly distinguish one powder from the other; however most of the powders had relatively close dielectric responses and only Talc had a resonance signature recorded at 1.135 THz. Furthermore, due to

  15. Material Properties Analysis of Structural Members in Pumpkin Balloons

    Science.gov (United States)

    Sterling, W. J.

    2003-01-01

    The efficient design, service-life qualification, and reliability predictions for lightweight aerospace structures require careful mechanical properties analysis of candidate structural materials. The demand for high-quality laboratory data is particularly acute when the candidate material or the structural design has little history. The pumpkin-shaped super-pressure balloon presents both challenges. Its design utilizes load members (tendons) extending from apex to base around the gas envelope to achieve a lightweight structure. The candidate tendon material is highly weight-efficient braided HM cord. Previous mechanical properties studies of Zylon have focused on fiber and yarn, and industrial use of the material in tensile applications is limited. For high-performance polymers, a carefully plamed and executed properties analysis scheme is required to ensure the data are relevant to the desired application. Because no directly-applicable testing standard was available, a protocol was developed based on guidelines fiom professional and industry organizations. Due to the liquid-crystalline nature of the polymer, the cord is very stiff, creeps very little, and does not yield. Therefore, the key material property for this application is the breaking strength. The pretension load and gauge length were found to have negligible effect on the measured breaking strength over the ranges investigated. Strain rate was found to have no effect on breaking strength, within the range of rates suggested by the standards organizations. However, at the lower rate more similar to ULDB operations, the strength was reduced. The breaking strength increased when the experiment temperature was decreased from ambient to 183K which is the lowest temperature ULDB is expected to experience. The measured strength under all test conditions was well below that resulting from direct scale-up of fiber strength based on the manufacturers data. This expected result is due to the effects of the

  16. Structural properties of laminated Douglas fir/epoxy composite material

    Energy Technology Data Exchange (ETDEWEB)

    Spera, D.A. (National Aeronautics and Space Administration, Cleveland, OH (USA). Lewis Research Center); Esgar, J.B. (Sverdrup Technology, Inc., Cleveland, OH (USA)); Gougeon, M.; Zuteck, M.D. (Gougeon Bros., Bay City, MI (USA))

    1990-05-01

    This publication contains a compilation of static and fatigue and strength data for laminated-wood material made from Douglas fir and epoxy. Results of tests conducted by several organizations are correlated to provide insight into the effects of variables such as moisture, size, lamina-to-lamina joint design, wood veneer grade, and the ratio of cyclic stress to steady stress during fatigue testing. These test data were originally obtained during development of wood rotor blades for large-scale wind turbines of the horizontal-axis (propeller) configuration. Most of the strength property data in this compilation are not found in the published literature. Test sections ranged from round cylinders 2.25 in. in diameter to rectangular slabs 6 in. by 24 in. in cross section and approximately 30 ft long. All specimens were made from Douglas fir veneers 0.10 in. thick, bonded together with the WEST epoxy system developed for fabrication and repair of wood boats. Loading was usually parallel to the grain. Size effects (reduction in strength with increase in test volume) are observed in some of the test data, and a simple mathematical model is presented that includes the probability of failure. General characteristics of the wood/epoxy laminate are discussed, including features that make it useful for a wide variety of applications. 9 refs.

  17. Inversion of Scattered Waves for Material Properties in Fractured Rock

    Energy Technology Data Exchange (ETDEWEB)

    Gritto, Roland; Korneev, Valeri A.; Johnson, Lane R.

    1999-07-01

    The authors apply a recently developed low-frequency, non-linear inversion method which includes near and far field terms to a crosshole data set to determine the bulk and shear modulus, as well as the density for a fractured zone in a granitic rock mass. The method uses the scattered elastic wavefield which is extracted from the recorded data before the inversion is performed. The inversion result is appraised by investigating the resolution and standard deviation of the model estimates. The sensitivity of the three parameters to different features of the medium is revealed. While the bulk modulus appears to be sensitive to voids and welded contacts, the density is mostly affected by fractured zones. The shear modulus is least constrained due to the absence of S wave anisotropy information. It is shown that the three medium parameters are generally sensitive to other medium features than those determined by velocity inversions. Thus this method is viewed as a complimentary approach to travel time tomography which provides more insight into the material properties of inhomogeneous media.

  18. Structural properties of laminated Douglas fir/epoxy composite material

    Science.gov (United States)

    Spera, David A.; Esgar, Jack B.; Gougeon, Meade; Zuteck, Michael D.

    1990-01-01

    This publication contains a compilation of static and fatigue strength data for laminated-wood material made from Douglas fir and epoxy. Results of tests conducted by several organizations are correlated to provide insight into the effects of variables such as moisture, size, lamina-to-lamina joint design, wood veneer grade, and the ratio of cyclic stress to steady stress during fatigue testing. These test data were originally obtained during development of wood rotor blades for large-scale wind turbines of the horizontal-axis (propeller) configuration. Most of the strength property data in this compilation are not found in the published literature. Test sections ranged from round cylinders 2.25 in. in diameter to rectangular slabs 6 by 24 in. in cross section and approximately 30 ft. long. All specimens were made from Douglas fir veneers 0.10 in. thick, bonded together with the WEST epoxy system developed for fabrication and repair of wood boats. Loading was usually parallel to the grain. Size effects (reduction in strength with increase in test volume) are observed in some of the test data, and a simple mathematical model is presented that includes the probability of failure. General characteristics of the wood/epoxy laminate are discussed, including features that make it useful for a wide variety of applications.

  19. Unravelling the materials genome: Symmetry relationships in alloy properties

    Energy Technology Data Exchange (ETDEWEB)

    Toda-Caraballo, Isaac [Department of Materials Science and Metallurgy, University of Cambridge New Museums Site, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom); Galindo-Nava, Enrique I. [Department of Materials Science and Metallurgy, University of Cambridge New Museums Site, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom); Delft University of Technology, Mekelweg 2, Delft 2628 CD (Netherlands); Rivera-Díaz-del-Castillo, Pedro E.J., E-mail: pejr2@cam.ac.uk [Department of Materials Science and Metallurgy, University of Cambridge New Museums Site, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom)

    2013-07-25

    Highlights: ► Research strategy for Accelerated Metallurgy project is outlined. ► Surprising symmetry among atomic, nanoscale and mechanical properties. ► Generalisation of Ashby diagrams via principal component analysis. ► Atomic-related properties can be described with linear regression. ► Mechanical properties modelled via Kocks–Mecking-type physical method. -- Abstract: Metals and alloys have been indispensable for technological progress, but only a fraction of the possible ternary systems (combinations of three elements) is known. Statistical inference methods combined with physical models are presented to discover new systems of enhanced properties. It is demonstrated that properties originating from atomic-level interactions can be described employing a linear regression analysis, but properties incorporating microstructural and thermal history effects require a balance between physical and statistical modelling. In spite of this, there is a remarkable degree of symmetry among all properties, and by employing a principal components analysis it is shown that ten properties essential to engineering can be described well in a three dimensional space. This will aid in the discovery of novel alloying systems.

  20. How to determine composite material properties using numerical homogenization

    DEFF Research Database (Denmark)

    Andreassen, Erik; Andreasen, Casper Schousboe

    2014-01-01

    Numerical homogenization is an efficient way to determine effective macroscopic properties, such as the elasticity tensor, of a periodic composite material. In this paper an educational description of the method is provided based on a short, self-contained Matlab implementation. It is shown how t...... cell of the periodic material can take the shape of a square, rectangle, or parallelogram, allowing for all kinds of 2D periodicities. © 2013 Elsevier B.V. All rights reserved.......Numerical homogenization is an efficient way to determine effective macroscopic properties, such as the elasticity tensor, of a periodic composite material. In this paper an educational description of the method is provided based on a short, self-contained Matlab implementation. It is shown how...... the basic code, which computes the effective elasticity tensor of a two material composite, where one material could be void, is easily extended to include more materials. Furthermore, extensions to homogenization of conductivity, thermal expansion, and fluid permeability are described in detail. The unit...

  1. Materials Characterization at Utah State University: Facilities and Knowledge-base of Electronic Properties of Materials Applicable to Spacecraft Charging

    Science.gov (United States)

    Dennison, J. R.; Thomson, C. D.; Kite, J.; Zavyalov, V.; Corbridge, Jodie

    2004-01-01

    In an effort to improve the reliability and versatility of spacecraft charging models designed to assist spacecraft designers in accommodating and mitigating the harmful effects of charging on spacecraft, the NASA Space Environments and Effects (SEE) Program has funded development of facilities at Utah State University for the measurement of the electronic properties of both conducting and insulating spacecraft materials. We present here an overview of our instrumentation and capabilities, which are particularly well suited to study electron emission as related to spacecraft charging. These measurements include electron-induced secondary and backscattered yields, spectra, and angular resolved measurements as a function of incident energy, species and angle, plus investigations of ion-induced electron yields, photoelectron yields, sample charging and dielectric breakdown. Extensive surface science characterization capabilities are also available to fully characterize the samples in situ. Our measurements for a wide array of conducting and insulating spacecraft materials have been incorporated into the SEE Charge Collector Knowledge-base as a Database of Electronic Properties of Materials Applicable to Spacecraft Charging. This Database provides an extensive compilation of electronic properties, together with parameterization of these properties in a format that can be easily used with existing spacecraft charging engineering tools and with next generation plasma, charging, and radiation models. Tabulated properties in the Database include: electron-induced secondary electron yield, backscattered yield and emitted electron spectra; He, Ar and Xe ion-induced electron yields and emitted electron spectra; photoyield and solar emittance spectra; and materials characterization including reflectivity, dielectric constant, resistivity, arcing, optical microscopy images, scanning electron micrographs, scanning tunneling microscopy images, and Auger electron spectra. Further

  2. Material properties of zooplankton and nekton from the California current

    Science.gov (United States)

    Becker, Kaylyn

    contrast were investigated. The sound speed contrast (h) was measured for Pacific hake flesh, myctophid flesh, Humboldt squid mantle, and Humboldt squid braincase. Sound speed varied within and between nekton taxa. The material properties reported in this study can be used to improve target strength estimates from acoustic scattering models which would increase the accuracy of biomass estimates from acoustic surveys for these zooplankton and nekton.

  3. Biologic properties of surgical scaffold materials derived from dermal ECM.

    Science.gov (United States)

    Kulig, Katherine M; Luo, Xiao; Finkelstein, Eric B; Liu, Xiang-Hong; Goldman, Scott M; Sundback, Cathryn A; Vacanti, Joseph P; Neville, Craig M

    2013-07-01

    Surgical scaffold materials manufactured from donor human or animal tissue are increasingly being used to promote soft tissue repair and regeneration. The clinical product consists of the residual extracellular matrix remaining after a rigorous decellularization process. Optimally, the material provides both structural support during the repair period and cell guidance cues for effective incorporation into the regenerating tissue. Surgical scaffold materials are available from several companies and are unique products manufactured by proprietary methodology. A significant need exists for a more thorough understanding of scaffold properties that impact the early steps of host cell recruitment and infiltration. In this study, a panel of in vitro assays was used to make direct comparisons of several similar, commercially-available materials: Alloderm, Medeor Matrix, Permacol, and Strattice. Differences in the materials were detected for both cell signaling and scaffold architecture-dependent cell invasion. Material-conditioned media studies found Medeor Matrix to have the greatest positive effect upon cell proliferation and induction of migration. Strattice provided the greatest chemotaxis signaling and best suppressed apoptotic induction. Among assays measuring structure-dependent properties, Medeor Matrix was superior for cell attachment, followed by Permacol. Only Alloderm and Medeor Matrix supported chemotaxis-driven cell invasion beyond the most superficial zone. Medeor Matrix was the only material in the chorioallantoic membrane assay to support substantial cell invasion. These results indicate that both biologic and structural properties need to be carefully assessed in the considerable ongoing efforts to develop new uses and products in this important class of biomaterials. Copyright © 2013 Elsevier Ltd. All rights reserved.

  4. Temporal properties of material categorization and material rating: visual vs non-visual material features.

    Science.gov (United States)

    Nagai, Takehiro; Matsushima, Toshiki; Koida, Kowa; Tani, Yusuke; Kitazaki, Michiteru; Nakauchi, Shigeki

    2015-10-01

    Humans can visually recognize material categories of objects, such as glass, stone, and plastic, easily. However, little is known about the kinds of surface quality features that contribute to such material class recognition. In this paper, we examine the relationship between perceptual surface features and material category discrimination performance for pictures of materials, focusing on temporal aspects, including reaction time and effects of stimulus duration. The stimuli were pictures of objects with an identical shape but made of different materials that could be categorized into seven classes (glass, plastic, metal, stone, wood, leather, and fabric). In a pre-experiment, observers rated the pictures on nine surface features, including visual (e.g., glossiness and transparency) and non-visual features (e.g., heaviness and warmness), on a 7-point scale. In the main experiments, observers judged whether two simultaneously presented pictures were classified as the same or different material category. Reaction times and effects of stimulus duration were measured. The results showed that visual feature ratings were correlated with material discrimination performance for short reaction times or short stimulus durations, while non-visual feature ratings were correlated only with performance for long reaction times or long stimulus durations. These results suggest that the mechanisms underlying visual and non-visual feature processing may differ in terms of processing time, although the cause is unclear. Visual surface features may mainly contribute to material recognition in daily life, while non-visual features may contribute only weakly, if at all.

  5. Radiative properties of materials with surface scattering or volume scattering: A review

    Institute of Scientific and Technical Information of China (English)

    Qunzhi ZHU; Hyunjin LEE; Zhuomin M. ZHANG

    2009-01-01

    Radiative properties of rough surfaces, parti-culate media and porous materials are important in thermal engineering and many other applications. These properties are often needed for calculating heat transfer between surfaces and volume elements in participating media, as well as for accurate radiometric temperature measure-ments. In this paper, recent research on scattering of thermal radiation by rough surfaces, fibrous insulation, soot, aerogel, biological materials, and polytetrafluor-oethylene (PTFE) is reviewed. Both theoretical modeling and experimental investigation are discussed. Rigorous solutions and approximation methods for surface scattering and volume scattering are described. The approach of using measured surface roughness statistics in Monte Carlo simulations to predict radiative properties of rough surfaces is emphasized. The effects of various parameters on the radiative properties of particulate media and porous materials are summarized.

  6. Use of UHPC in Bridge Structures: Material Modeling and Design

    Directory of Open Access Journals (Sweden)

    Oguz Gunes

    2012-01-01

    Full Text Available Ultra-high-performance concrete (UHPC is a promising new class of concrete material that is likely to make a significant contribution to addressing the challenges associated with the load capacity, durability, sustainability, economy, and environmental impact of concrete bridge infrastructures. This paper focuses on the material modeling of UHPC and design of bridge girders made of UHPC. A two-phase model used for modeling the behavior of UHPC was briefly discussed, and the model was implemented in a preliminary design case study. Based on the implemented design and the reported use of UHPC in bridge applications, the advantages, limitations, and future prospects of UHPC bridges were discussed, highlighting the need for innovative research and design to make optimum use of the favorable properties of the material in bridge structures.

  7. Numerical Investigation of a Moisture Evaporation Model in Building Materials

    CERN Document Server

    Amirkhanov, I V; Pavlish, M; Puzynina, T P; Puzynin, I V; Sarhadov, I

    2005-01-01

    The properties of a model of moisture evaporation in a porous building material of a rectangular form proposed in [1] are investigated. Algorithms of solving a nonlinear diffusion equation with initial and boundary conditions simulating the dynamic distribution of moisture concentration, calculation of coefficients of a polynomial describing transport of moisture with usage of experimental measurement of moisture concentration in a sample are developed and investigated. Research on the properties of the model is carried out depending on the degree of the polynomial, a set of its coefficients, and the quantity of the used experimental data.

  8. Composite materials. Volume 1: Properties, non-destructive testing, and repair

    Energy Technology Data Exchange (ETDEWEB)

    Schwartz, M.M. [United Technologies Corp., East Hartford, CT (United States)

    1997-12-31

    This book provides a practical overview of the different types, properties, applications and design implementations of the latest composite materials. It describes important composite families, including metals, ceramics, polymers and other engineered materials; shows how each type of composite may be designed, manufactured, strengthened, and repaired; introduces composite modeling techniques; and explains the major industrial applications for composites. Primary markets for this book include materials engineers and designers in aerospace, automotive and transportation industries; works managers, facilities engineers, test engineers, plant engineers, manufacturing and industrial engineers, and production managers; students in material science, mechanical engineering and metallurgy.

  9. Microstructure characterization and magnetic properties of nano structured materials

    Energy Technology Data Exchange (ETDEWEB)

    Sun, X.C

    2000-07-01

    The present thesis deals with the unique microstructural properties and their novel magnetic properties of core-shell Ni-Ce nano composite particles, carbon encapsulated Fe, Co, and Ni nanoparticles and the nano crystallization behavior of typical ferromagnetic Fe{sub 78}Si{sub 9}B{sub 13} ribbons. These properties have intensively been investigated by high resolution transmission electron microscopy (HREM), X-ray diffraction (XRD), scanning electron microscopy (Sem), X-ray energy dispersive spectroscopy [eds.]; selected area electron diffraction pattern (SAED), Ft-IR, differential scanning calorimeter (DSC). In addition, magnetic moments measurements at different temperatures and applied fields have been performed by transmission Moessbauer spectroscopy, superconducting quantum interference device magnetometer (SQUID), and vibrating sample magnetometer (VSM). The present studies may provide the insights for the better understanding of the correlation between the unique microstructure and novel magnetic properties for several magnetic nano structured materials. (Author)

  10. Material Properties of High-Speed Steel Rolls

    Directory of Open Access Journals (Sweden)

    Shaohua Wu

    2017-03-01

    Full Text Available Recently, it has been required to improve the material properties of high-speed steel (HSS rolls, because of the low wear resistance and low mechanical properties. To improve them, several new steels have been proposed, which have high wear resistance as well as excellent mechanical properties, e.g., hardness and tensile properties, where additional elements (V, Cr and W were employed. However, their steels may have still technical issues, as the roll surfaces become roughened during the production process. The reason for this problem is found to be affected by the oxidation of the HSS surface. In this work, we have provided the suggestions to make high wear resistance of the HSS rolls

  11. Rectangular waveguide material characterization: anisotropic property extraction and measurement validation

    Science.gov (United States)

    Crowgey, Benjamin Reid

    for characterization of a sample filling the cross-section of a waveguide. Due to the rectangular nature of the waveguide, typically three different samples are manufactured from the same material in order to characterize the six complex material parameters. The second technique for measuring the electromagnetic properties of a biaxially anisotropic material sample uses a reduced-aperture waveguide sample holder designed to accommodate a cubical sample. All the tensor material parameters can then be determined by measuring the reflection and transmission coefficients of a single sample placed into several orientations. The parameters are obtained using a root-searching algorithm by comparing theoretically computed and measured reflection and transmission coefficients. The theoretical coefficients are determined using a mode matching technique. The first technique for characterizing the electromagnetic properties of gyromagnetic materials considers requires filling the cross-section of a waveguide. The material parameters are extracted from the measured reflection and transmission coefficients. Since the cross-sectional dimensions of waveguides become prohibitively large at low frequencies, and it is at these frequencies that the gyromagnetic properties are most pronounced, sufficiently large samples may not be available. Therefore, the second technique uses a reduced-aperture sample holder that does not require the sample to fill the entire cross section of the guide. The theoretical reflection and transmission coefficients for both methods are determined using a mode matching technique. A nonlinear least squares method is employed to extract the gyromagnetic material parameters. Finally, this dissertation introduces a waveguide standard that acts as a surrogate material with both electric and magnetic properties and is useful for verifying systems designed to characterize engineered materials using the NRW technique. A genetic algorithm is used to optimize the all

  12. Further developments in material properties determined by vibration analysis

    DEFF Research Database (Denmark)

    Nielsen, Lauge Fuglsang; Andreasen, Lotte; Seifert, Mette

    1997-01-01

    have been studied by testing a number of building materials. The method has been PC-integrated with the Brüel & Kjær's type 3550 vibration equipment - and special user menus have been developed to facilitate handling of the method in practice. Limits on range of test frequencies applied are discussed...... with respect to configurations of vibration equipment and shapes of test specimens used. Sensitivity studies have been made to identify sources of errors which may disturb the reliability of the method used in practice. Practical aspects with respect to test set-ups are considered in these studies - as well......A method was described in Materialnyt 1 (1995) on "Material properties determined by vibration analysis". This new method of materials testing has been further developed as the result of research at the Building Materials Laboratory, Technical University of Denmark.Practical aspects of the method...

  13. Correlation of macroscopic material properties with microscopic nuclear data

    Energy Technology Data Exchange (ETDEWEB)

    Simons, R.L.

    1981-12-18

    Two primary irradiation-induced changes occur during neutron irradiation: the displacement of atoms forming crystal defects and the transmutation of atoms into either gaseous or solid products. The material scientist studying irradiation damage to material by fusion-produced neutrons is faced with several questions: Is the nature of high-energy (14-MeV) displacement damage the same as or different from that caused by fission neutrons (< 2 MeV). How do the high helium concentrations expected in a fusion environment affect the material properties. What effects do solid transmutation products have on the behavior of the irradiated materials. In the past few years, much work has been done to answer these questions. This paper reviews recent work in this area.

  14. Thermal property of insulation material for HTS power cable

    Science.gov (United States)

    Choi, Yeon Suk; Kim, D. L.; Shin, D. W.; Hwang, S. D.

    2012-06-01

    The thermal property of insulation material is essential in developing a high temperature superconductor (HTS) power cable operating at around liquid nitrogen temperature. The accurate estimate of the heat flux is difficult in the nonmetallic materials because nonmetallic materials have a high thermal resistance and low temperature gradient along the specimen. The objective of the present work is to develop a precise instrument for measuring the thermal conductivity of insulating materials over a temperature range of 30 K to approximately the room temperature by using a cryocooler. The thermal conductivity of Teflon is measured and the accuracy confirmation is carried out by comparing published data. In addition, the experimental results of apparent thermal conductivity of polypropylene laminated paper (PPLP) are presented and the temperature dependency is also discussed

  15. A FEM-based method to determine the complex material properties of piezoelectric disks.

    Science.gov (United States)

    Pérez, N; Carbonari, R C; Andrade, M A B; Buiochi, F; Adamowski, J C

    2014-08-01

    Numerical simulations allow modeling piezoelectric devices and ultrasonic transducers. However, the accuracy in the results is limited by the precise knowledge of the elastic, dielectric and piezoelectric properties of the piezoelectric material. To introduce the energy losses, these properties can be represented by complex numbers, where the real part of the model essentially determines the resonance frequencies and the imaginary part determines the amplitude of each resonant mode. In this work, a method based on the Finite Element Method (FEM) is modified to obtain the imaginary material properties of piezoelectric disks. The material properties are determined from the electrical impedance curve of the disk, which is measured by an impedance analyzer. The method consists in obtaining the material properties that minimize the error between experimental and numerical impedance curves over a wide range of frequencies. The proposed methodology starts with a sensitivity analysis of each parameter, determining the influence of each parameter over a set of resonant modes. Sensitivity results are used to implement a preliminary algorithm approaching the solution in order to avoid the search to be trapped into a local minimum. The method is applied to determine the material properties of a Pz27 disk sample from Ferroperm. The obtained properties are used to calculate the electrical impedance curve of the disk with a Finite Element algorithm, which is compared with the experimental electrical impedance curve. Additionally, the results were validated by comparing the numerical displacement profile with the displacements measured by a laser Doppler vibrometer. The comparison between the numerical and experimental results shows excellent agreement for both electrical impedance curve and for the displacement profile over the disk surface. The agreement between numerical and experimental displacement profiles shows that, although only the electrical impedance curve is

  16. Alkali-activated cementitious materials: Mechanisms, microstructure and properties

    Science.gov (United States)

    Jiang, Weimin

    The goal of this study was to examine the activation reaction, microstructure, properties, identify the mechanisms of activation, and achieve an enhanced understanding of activation processes occurring during the synthesis of alkali activated cementitious materials (AAC). The discussions classify the following categories. (1) alkali activated slag cement; (2) alkali activated portland-slag cement; (3) alkali activated fly ash-slag cement; (4) alkali activated pozzolana-lime cement; (5) alkali activated pozzolana cement. The activators involved are NaOH, KOH; Nasb2SOsb4;\\ Nasb2COsb3;\\ CaSOsb4, and soluble silicate of sodium and potassium. The effect of alkali activation on the microstructure of these materials were analyzed at the micro-nanometer scale by SEM, EDS, ESEM, and TEM. Also sp{29}Si and sp{27}Al MAS-NMR, IR, Raman, TGA, and DTA were performed to characterize the phase in these systems. Slag, fly ash, silica fume, as well as blended cements containing mixtures of these and other components were characterized. A set of ordinary portland cement paste samples served as a control. This study confirmed that AAC materials have great potential because they could generate very early high strength, greater durability and high performance. Among the benefits to be derived from this research is a better understanding of the factors that control concrete properties when using AAC materials, and by controlling the chemistry and processing to produce desired microstructures and properties, as well as their durability.

  17. Mechanical Properties of Calcium Fluoride-Based Composite Materials

    Science.gov (United States)

    Kleczewska, Joanna; Pryliński, Mariusz; Podlewska, Magdalena; Sokołowski, Jerzy; Łapińska, Barbara

    2016-01-01

    Aim of the study was to evaluate mechanical properties of light-curing composite materials modified with the addition of calcium fluoride. The study used one experimental light-curing composite material (ECM) and one commercially available flowable light-curing composite material (FA) that were modified with 0.5–5.0 wt% anhydrous calcium fluoride. Morphology of the samples and uniformity of CaF2 distribution were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS). Mechanical properties were tested after 24-hour storage of specimens in dry or wet conditions. Stored dry ECM enriched with 0.5–1.0 wt% CaF2 showed higher tensile strength values, while water storage of all modified ECM specimens decreased their tensile strength. The highest Vickers hardness tested after dry storage was observed for 2.5 wt% CaF2 content in ECM. The addition of 2.0–5.0 wt% CaF2 to FA caused significant decrease in tensile strength after dry storage and overall tensile strength decrease of modified FA specimens after water storage. The content of 2.0 wt% CaF2 in FA resulted in the highest Vickers hardness tested after wet storage. Commercially available composite material (FA), unmodified with fluoride addition, demonstrated overall significantly higher mechanical properties. PMID:28004001

  18. Mechanical Properties of Calcium Fluoride-Based Composite Materials

    Directory of Open Access Journals (Sweden)

    Monika Łukomska-Szymańska

    2016-01-01

    Full Text Available Aim of the study was to evaluate mechanical properties of light-curing composite materials modified with the addition of calcium fluoride. The study used one experimental light-curing composite material (ECM and one commercially available flowable light-curing composite material (FA that were modified with 0.5–5.0 wt% anhydrous calcium fluoride. Morphology of the samples and uniformity of CaF2 distribution were analyzed using Scanning Electron Microscopy (SEM and Energy Dispersive Spectroscopy (EDS. Mechanical properties were tested after 24-hour storage of specimens in dry or wet conditions. Stored dry ECM enriched with 0.5–1.0 wt% CaF2 showed higher tensile strength values, while water storage of all modified ECM specimens decreased their tensile strength. The highest Vickers hardness tested after dry storage was observed for 2.5 wt% CaF2 content in ECM. The addition of 2.0–5.0 wt% CaF2 to FA caused significant decrease in tensile strength after dry storage and overall tensile strength decrease of modified FA specimens after water storage. The content of 2.0 wt% CaF2 in FA resulted in the highest Vickers hardness tested after wet storage. Commercially available composite material (FA, unmodified with fluoride addition, demonstrated overall significantly higher mechanical properties.

  19. Discrete element modelling of granular materials

    NARCIS (Netherlands)

    Van Baars, S.

    1996-01-01

    A new model is developed by the author, which does not use the equations of motion but the equations of equilibrium to describe granular materials. The numerical results show great similarities with reality and can generally be described by an advanced Mohr-Coulomb model. However, many contacts betw

  20. Method for the unique identification of hyperelastic material properties using full-field measures. Application to the passive myocardium material response.

    Science.gov (United States)

    Perotti, Luigi E; Ponnaluri, Aditya V S; Krishnamoorthi, Shankarjee; Balzani, Daniel; Ennis, Daniel B; Klug, William S

    2017-01-18

    Quantitative measurement of the material properties (eg, stiffness) of biological tissues is poised to become a powerful diagnostic tool. There are currently several methods in the literature to estimating material stiffness, and we extend this work by formulating a framework that leads to uniquely identified material properties. We design an approach to work with full-field displacement data-ie, we assume the displacement field due to the applied forces is known both on the boundaries and also within the interior of the body of interest-and seek stiffness parameters that lead to balanced internal and external forces in a model. For in vivo applications, the displacement data can be acquired clinically using magnetic resonance imaging while the forces may be computed from pressure measurements, eg, through catheterization. We outline a set of conditions under which the least-square force error objective function is convex, yielding uniquely identified material properties. An important component of our framework is a new numerical strategy to formulate polyconvex material energy laws that are linear in the material properties and provide one optimal description of the available experimental data. An outcome of our approach is the analysis of the reliability of the identified material properties, even for material laws that do not admit unique property identification. Lastly, we evaluate our approach using passive myocardium experimental data at the material point and show its application to identifying myocardial stiffness with an in silico experiment modeling the passive filling of the left ventricle. Copyright © 2017 John Wiley & Sons, Ltd.

  1. Multiscale Materials Modeling in an Industrial Environment.

    Science.gov (United States)

    Weiß, Horst; Deglmann, Peter; In 't Veld, Pieter J; Cetinkaya, Murat; Schreiner, Eduard

    2016-06-07

    In this review, we sketch the materials modeling process in industry. We show that predictive and fast modeling is a prerequisite for successful participation in research and development processes in the chemical industry. Stable and highly automated workflows suitable for handling complex systems are a must. In particular, we review approaches to build and parameterize soft matter systems. By satisfying these prerequisites, efficiency for the development of new materials can be significantly improved, as exemplified here for formulation polymer development. This is in fact in line with recent Materials Genome Initiative efforts sponsored by the US government. Valuable contributions to product development are possible today by combining existing modeling techniques in an intelligent fashion, provided modeling and experiment work hand in hand.

  2. Hysteretic behavior modeling of elastoplastic materials

    Directory of Open Access Journals (Sweden)

    Šumarac Dragoslav

    2008-01-01

    Full Text Available In the present paper the Preisach model of hysteresis is applied to model cyclic behavior of elasto-plastic material. Rate of loading and viscous effects will not be considered. The problem of axial loading of rectangular cross section and cyclic bending of rectangular tube (box will be studied in details. Hysteretic stress-strain loop for prescribed history of stress change is plotted for material modeled by series connection of three unite element. Also moment-curvature hysteretic loop is obtained for a prescribed curvature change of rectangular tube (box. One chapter of the paper is devoted to results obtained by FEM using Finite Element Code ABAQUS. All obtained results clearly show advantages of the Preisach model for describing cyclic behavior of elasto-plastic material.

  3. Elastic therapeutic tape: do they have the same material properties?

    Science.gov (United States)

    Boonkerd, Chuanpis; Limroongreungrat, Weerawat

    2016-01-01

    [Purpose] Elastic therapeutic tape has been widely used for rehabilitation and treatment of sports injuries. Tapes with different elastic properties serve different treatment purposes with inappropriate tension reducing tape effectiveness. Many tapes are available in the market, but studies on tape properties are limited. The aim of this study was to examine the material properties of elastic therapeutic tape. [Subjects and Methods] Brands of elastic therapeutic tape included KinesioTex®, ATex, Mueller, 3M, and ThaiTape. The Material Testing System Insight® 1 Electromechanical Testing Systems was used to apply a tensile force on elastic therapeutic tape. Ten specimens of each brand were tested. Stress, load, and Young’s modulus at 25%, 50%, 75%, 100%, and maximum point were collected. One-way analysis of variance with post hoc testing was used to analyze tape parameters. [Results] Maximum elongation and Young’s modulus at all percentages were significantly different between brands. There were no differences in maximum load and maximum stress. [Conclusion] Mechanical properties are different for commercial elastic therapeutic tapes. Physiotherapists and other clinicians should be aware of mechanical tape properties to correctly apply kinesio tape. PMID:27190472

  4. Elastic therapeutic tape: do they have the same material properties?

    Science.gov (United States)

    Boonkerd, Chuanpis; Limroongreungrat, Weerawat

    2016-04-01

    [Purpose] Elastic therapeutic tape has been widely used for rehabilitation and treatment of sports injuries. Tapes with different elastic properties serve different treatment purposes with inappropriate tension reducing tape effectiveness. Many tapes are available in the market, but studies on tape properties are limited. The aim of this study was to examine the material properties of elastic therapeutic tape. [Subjects and Methods] Brands of elastic therapeutic tape included KinesioTex(®), ATex, Mueller, 3M, and ThaiTape. The Material Testing System Insight(®) 1 Electromechanical Testing Systems was used to apply a tensile force on elastic therapeutic tape. Ten specimens of each brand were tested. Stress, load, and Young's modulus at 25%, 50%, 75%, 100%, and maximum point were collected. One-way analysis of variance with post hoc testing was used to analyze tape parameters. [Results] Maximum elongation and Young's modulus at all percentages were significantly different between brands. There were no differences in maximum load and maximum stress. [Conclusion] Mechanical properties are different for commercial elastic therapeutic tapes. Physiotherapists and other clinicians should be aware of mechanical tape properties to correctly apply kinesio tape.

  5. Analysis of Mechanical Properties of Fabrics of Different Raw Material

    Directory of Open Access Journals (Sweden)

    Aušra ADOMAITIENĖ

    2011-07-01

    Full Text Available The study analyzes dependence of mechanical properties (breaking force, elongation at break, static friction force and static friction coefficient on integrated fabric structure factor j and raw material density r, among the fabrics of different raw material (cotton, wool, polypropylene, polyester and polyacrylnitrile and woven in different conditions. The received results demonstrate that sometimes strong dependences exist (wool, polypropylene and polyacrylnitrile, whereas in some cases (cotton and polyester there is no correlation. It was also discovered that the breaking force and elongation at break in the direction of weft increase, when fabric structure becomes more rigid. In the meantime variations of the curves in the direction of warp are insignificant. Regarding static friction force and static friction coefficient (found in two cases, when fabrics were rubbing against leather and materials, it was discovered that consistency of the curves is irregular, i. e. they either increase or decrease, when integrated fabric structure factor j growth. It was also identified that some dependences are not strong and relationship between explored and analyzed factors does not exist. Variation of all these mechanical properties with respect to material density r enables to conclude that increase of material density r results in poor dependences or they are whatsoever non-existent.http://dx.doi.org/10.5755/j01.ms.17.2.487

  6. A bespoke single-band Hubbard model material

    Science.gov (United States)

    Griffin, S. M.; Staar, P.; Schulthess, T. C.; Troyer, M.; Spaldin, N. A.

    2016-02-01

    The Hubbard model, which augments independent-electron band theory with a single parameter to describe electron-electron correlations, is widely regarded to be the "standard model" of condensed-matter physics. The model has been remarkably successful at addressing a range of correlation phenomena in solids, but it neglects many behaviors that occur in real materials, such as phonons, long-range interactions, and, in its simplest form, multiorbital effects. Here, we use ab initio electronic structure methods to design a material whose Hamiltonian matches as closely as possible that of the single-band Hubbard model. Our motivation is to compare the measured properties of our new material to those predicted by reliable theoretical solutions of the Hubbard model to determine the relevance of the model in the description of real materials. After identifying an appropriate crystal class and several appropriate chemistries, we use density-functional theory and dynamical mean-field theory to screen for the desired electronic band structure and metal-insulator transition. We then explore the most promising candidates for structural stability and suitability for doping, and we propose specific materials for subsequent synthesis. Finally, we identify a regime—that should manifest in our bespoke material—in which the single-band Hubbard model on a triangular lattice exhibits exotic d -wave superconductivity.

  7. Preparation and Properties of Orthogonal Piezoelectric Composite Materials

    Institute of Scientific and Technical Information of China (English)

    Liu Jun; Lu Ying; Zhang Xingguo; Shen Yi; Chen Chun

    2004-01-01

    . PZT piezoelectric ceramic with La2O3, SrCO3, BaO and Sb2O5 was prepared. It has high value of the piezoelectric strain constant d33 ( -681 PC/N) and high value of-d33/d31 (2.65). Orthogonal piezoelectric composite materials was designed and prepared by PZT, DAD- 40 electric conductive adhesive and E51 epoxy resin. The OPCM shows obvious orthogonal anisotropy. The matching property of the interface between piezoelectric ceramic and polymer of OPCM relies on the defects of interface. The proper conductive mid-layer could improve the matching property of the interface.

  8. Thermophysical properties of new materials; Proprietes thermophysiques des materiaux nouveaux

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    This conference day was organized by the `thermo-kinetics` section of the French association of thermal engineers. This book of proceedings contains 5 papers entitled: `characterization of thermal properties using periodical methods at the Odeillo test centre: developments and applications`; `measurement of the distribution of local thermophysical properties by IR images processing and averaging technique`; `extension of shock probes to the characterization of multi-layers - development of a simple device for the characterization of insulating materials or shear fluids`; `thermal local diffusivity of constituents of carbon/carbon composites`; `new method for the thermal diffusivity measurement of thermo-hardenable resins during polymerization`. (J.S.)

  9. Structure/property relationships in non-linear optical materials

    Energy Technology Data Exchange (ETDEWEB)

    Cole, J.M. [Institut Max von Laue - Paul Langevin (ILL), 38 - Grenoble (France)]|[Durham Univ. (United Kingdom); Howard, J.A.K. [Durham Univ. (United Kingdom); McIntyre, G.J. [Institut Max von Laue - Paul Langevin (ILL), 38 - Grenoble (France)

    1997-04-01

    The application of neutrons to the study of structure/property relationships in organic non-linear optical materials (NLOs) is described. In particular, charge-transfer effects and intermolecular interactions are investigated. Charge-transfer effects are studied by charge-density analysis and an example of one such investigation is given. The study of intermolecular interactions concentrates on the effects of hydrogen-bonding and an example is given of two structurally similar molecules with very disparate NLO properties, as a result of different types of hydrogen-bonding. (author). 3 refs.

  10. Relationships between fracture toughness and other material properties. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Perra, M.; Finnie, I.

    1974-01-01

    The key experimental and analytical studies which have led to our present understanding of the mechanisms of ductile fracture are reviewed. It is concluded that insufficient progress has been made in the quantitative description of ductile separation mechanisms on a microscale to allow the realistic prediction of fracture toughness from material properties and microstructure. An experimental study of ductile fracture is underway which has the aim of determining the growth rate of voids in known plastic deformation fields as a function of triaxiality of stress and material work-hardening. Novel specimens of particularly well characterized microstructure are utilized.

  11. Optical and other material properties of SiO2 from ab initio studies

    Science.gov (United States)

    Warmbier, Robert; Mohammed, Faris; Quandt, Alexander

    2014-07-01

    The optical properties of photonic devices largely depend on the dielectric properties of the underlying materials. We apply modern ab initio methods to study crystalline SiO2 phases, which serve as toy models for amorphous glass. We discuss the dielectric response from the infrared to the VIS/UV, which is crucial for glass based photonic applications. Low density silica, like cristobalite, may provide a good basis for high transmission optical devices.

  12. Numerical modeling of materials under extreme conditions

    CERN Document Server

    Brown, Eric

    2014-01-01

    The book presents twelve state of the art contributions in the field of numerical modeling of materials subjected to large strain, high strain rates, large pressure and high stress triaxialities, organized into two sections. The first part is focused on high strain rate-high pressures such as those occurring in impact dynamics and shock compression related phenomena, dealing with material response identification, advanced modeling incorporating microstructure and damage, stress waves propagation in solids and structures response under impact. The latter part is focused on large strain-low strain rates applications such as those occurring in technological material processing, dealing with microstructure and texture evolution, material response at elevated temperatures, structural behavior under large strain and multi axial state of stress.

  13. Finite amplitude effects on drop levitation for material properties measurement

    Science.gov (United States)

    Ansari Hosseinzadeh, Vahideh; Holt, R. Glynn

    2017-05-01

    The method of exciting shape oscillation of drops to extract material properties has a long history, which is most often coupled with the technique of acoustic levitation to achieve non-contact manipulation of the drop sample. We revisit this method with application to the inference of bulk shear viscosity and surface tension. The literature is replete with references to a "10% oscillation amplitude" as a sufficient condition for the application of Lamb's analytical expressions for the shape oscillations of viscous liquids. Our results show that even a 10% oscillation amplitude leads to dynamic effects which render Lamb's results inapplicable. By comparison with samples of known viscosity and surface tension, we illustrate the complicating finite-amplitude effects (mode-splitting and excess dissipation associated with vorticity) that can occur and then show that sufficiently small oscillations allow us to recover the correct material properties using Lamb's formula.

  14. Mechanical Properties of Materials with Nanometer Scale Microstructures

    Energy Technology Data Exchange (ETDEWEB)

    William D. Nix

    2004-10-31

    We have been engaged in research on the mechanical properties of materials with nanometer-scale microstructural dimensions. Our attention has been focused on studying the mechanical properties of thin films and interfaces and very small volumes of material. Because the dimensions of thin film samples are small (typically 1 mm in thickness, or less), specialized mechanical testing techniques based on nanoindentation, microbeam bending and dynamic vibration of micromachined structures have been developed and used. Here we report briefly on some of the results we have obtained over the past three years. We also give a summary of all of the dissertations, talks and publications completed on this grant during the past 15 years.

  15. Optical properties of glazing materials at normal incidence

    Energy Technology Data Exchange (ETDEWEB)

    Rubin, M.; Powles, R.

    2001-10-01

    Measurements of spectral transmittance T and reflectance R at normal incidence continue to be the most common and accurate source of energy performance data for glazing materials. Prediction of these radiometric properties from more fundamental materials data is often confounded by the complexity and uncertainty of coating structures. Angle-dependent radiometric properties of coated glazing will probably be predicted from normal-incidence data rather than being measured at many angles. The general error level demonstrated in round-robin tests is on the order 1-2%; it is often necessary to achieve better levels of performance. Based on results obtained following the round-robin tests, it is expected that accuracy of better than 0.5% can be generally achieved. A new type of absolute standard reference is described and tested with promising results.

  16. New Technique for Evaluating Adhesion Properties between Soft Materials

    Science.gov (United States)

    Sato, Takaya; Goto, Motoaki; Nakano, Ken; Suzuki, Atsushi

    2005-11-01

    A new, simple apparatus for measuring the surface adhesion properties of soft materials was designed, where the adhesion force of a point contact between soft materials and the total energy required to separate the contact can be measured using the springs of phosphor-bronze thin plates with strain gauges. The adhesion between swollen hydrogels was studied here by this simple technique in air at room temperature. The gels used in the present preliminary experiments were poly(sodium acrylate) hydrogels physically cross-linked by aluminum ions. The adhesion force and the separation energy showed a power-law increase with separation velocity. The apparatus was applied to evaluate the adhesion properties of seven anti-inflammatory analgesic cataplasms on the market. It was found that the easiness to separate (rank of adhesion force and the separation energy) was consistent with the results of those obtained by organoleptic evaluations.

  17. Textile Materials with New Properties Used for Confections Manufacturing

    Directory of Open Access Journals (Sweden)

    Neacşu A. N.

    2009-12-01

    Full Text Available The quality of textile clothing depends on the quality of prime materials and also on the technology used; this must ensure a balance between transferred heat, resulted humidity and human and environmental thermal demands, all this bringing about physiological comfort. In order to meet consumers’ demands regarding the production of products which are easy to maintain and have high hygiene properties, new prime materials are searched, with a view to ensuring a wide range of clothing. Taking into consideration the acceleration of changes and the global inter-connections, a company must develop its capacity of innovation in order to bring products with new properties on the market before others do.

  18. A generalized methodology to characterize composite materials for pyrolysis models

    Science.gov (United States)

    McKinnon, Mark B.

    The predictive capabilities of computational fire models have improved in recent years such that models have become an integral part of many research efforts. Models improve the understanding of the fire risk of materials and may decrease the number of expensive experiments required to assess the fire hazard of a specific material or designed space. A critical component of a predictive fire model is the pyrolysis sub-model that provides a mathematical representation of the rate of gaseous fuel production from condensed phase fuels given a heat flux incident to the material surface. The modern, comprehensive pyrolysis sub-models that are common today require the definition of many model parameters to accurately represent the physical description of materials that are ubiquitous in the built environment. Coupled with the increase in the number of parameters required to accurately represent the pyrolysis of materials is the increasing prevalence in the built environment of engineered composite materials that have never been measured or modeled. The motivation behind this project is to develop a systematic, generalized methodology to determine the requisite parameters to generate pyrolysis models with predictive capabilities for layered composite materials that are common in industrial and commercial applications. This methodology has been applied to four common composites in this work that exhibit a range of material structures and component materials. The methodology utilizes a multi-scale experimental approach in which each test is designed to isolate and determine a specific subset of the parameters required to define a material in the model. Data collected in simultaneous thermogravimetry and differential scanning calorimetry experiments were analyzed to determine the reaction kinetics, thermodynamic properties, and energetics of decomposition for each component of the composite. Data collected in microscale combustion calorimetry experiments were analyzed to

  19. Tensile Properties of Fiber Materials under Different Strain Rates

    Institute of Scientific and Technical Information of China (English)

    XIONG Jie; GU Bo-hong; WANG Shan-yuan

    2002-01-01

    The quasi-static and dynamic tensile tests of aranid and high strength PVA fiber bundles are carried out under a wider range of strain rate by use of MTS (Materials Testing System) and bar-bar tensile impact apparatus.The influences of strain rate on mechanical properties of aramid and high strength polyvinyl alcohol fibers ar estudied. Micro failure mechanisms of fibers at different strain rates are examined by means of SEM.

  20. Measurement of Mechanical Properties of Cantilever Shaped Materials

    Directory of Open Access Journals (Sweden)

    Thomas Thundat

    2008-05-01

    Full Text Available Microcantilevers were first introduced as imaging probes in Atomic Force Microscopy (AFM due to their extremely high sensitivity in measuring surface forces. The versatility of these probes, however, allows the sensing and measurement of a host of mechanical properties of various materials. Sensor parameters such as resonance frequency, quality factor, amplitude of vibration and bending due to a differential stress can all be simultaneously determined for a cantilever. When measuring the mechanical properties of materials, identifying and discerning the most influential parameters responsible for the observed changes in the cantilever response are important. We will, therefore, discuss the effects of various force fields such as those induced by mass loading, residual stress, internal friction of the material, and other changes in the mechanical properties of the microcantilevers. Methods to measure variations in temperature, pressure, or molecular adsorption of water molecules are also discussed. Often these effects occur simultaneously, increasing the number of parameters that need to be concurrently measured to ensure the reliability of the sensors. We therefore systematically investigate the geometric and environmental effects on cantilever measurements including the chemical nature of the underlying interactions. To address the geometric effects we have considered cantilevers with a rectangular or circular cross section. The chemical nature is addressed by using cantilevers fabricated with metals and/or dielectrics. Selective chemical etching, swelling or changes in Young’s modulus of the surface were investigated by means of polymeric and inorganic coatings. Finally to address the effect of the environment in which the cantilever operates, the Knudsen number was determined to characterize the molecule-cantilever collisions. Also bimaterial cantilevers with high thermal sensitivity were used to discern the effect of temperature

  1. Fatigue properties of high-strength materials used in cold-forging tools

    DEFF Research Database (Denmark)

    Brøndsted, P.; Skov-Hansen, P.

    1998-01-01

    In the present work classical analytical models are used to describe the static stress–strain curves, low-cycle fatigue properties and fatigue crack growth behaviour of high-strength materials for use in tools for metal-forming processes such as cold forging and extrusion. The paper describes...

  2. Nanocomposite C-Pd thin films – a new material with specific spectral properties

    Directory of Open Access Journals (Sweden)

    M. Suchańska

    2013-09-01

    Full Text Available In this paper, the results of optical investigations for thin films of carbon-palladium (C-Pd nanocomposites are presented. This films were prepared using two steps method (PVD/ CVD. The optical and Raman spectroscopy has been used to characterize the material. The multinanolayer model was used to explain the specific spectral properties.

  3. Modeling of Irradiation Hardening of Polycrystalline Materials

    Energy Technology Data Exchange (ETDEWEB)

    Li, Dongsheng; Zbib, Hussein M.; Garmestani, Hamid; Sun, Xin; Khaleel, Mohammad A.

    2011-09-14

    High energy particle irradiation of structural polycrystalline materials usually produces irradiation hardening and embrittlement. The development of predict capability for the influence of irradiation on mechanical behavior is very important in materials design for next generation reactors. In this work a multiscale approach was implemented to predict irradiation hardening of body centered cubic (bcc) alpha-iron. The effect of defect density, texture and grain boundary was investigated. In the microscale, dislocation dynamics models were used to predict the critical resolved shear stress from the evolution of local dislocation and defects. In the macroscale, a viscoplastic self-consistent model was applied to predict the irradiation hardening in samples with changes in texture and grain boundary. This multiscale modeling can guide performance evaluation of structural materials used in next generation nuclear reactors.

  4. Ocean acidification alters the material properties of Mytilus edulis shells.

    Science.gov (United States)

    Fitzer, Susan C; Zhu, Wenzhong; Tanner, K Elizabeth; Phoenix, Vernon R; Kamenos, Nicholas A; Cusack, Maggie

    2015-02-01

    Ocean acidification (OA) and the resultant changing carbonate saturation states is threatening the formation of calcium carbonate shells and exoskeletons of marine organisms. The production of biominerals in such organisms relies on the availability of carbonate and the ability of the organism to biomineralize in changing environments. To understand how biomineralizers will respond to OA the common blue mussel, Mytilus edulis, was cultured at projected levels of pCO2 (380, 550, 750, 1000 µatm) and increased temperatures (ambient, ambient plus 2°C). Nanoindentation (a single mussel shell) and microhardness testing were used to assess the material properties of the shells. Young's modulus (E), hardness (H) and toughness (KIC) were measured in mussel shells grown in multiple stressor conditions. OA caused mussels to produce shell calcite that is stiffer (higher modulus of elasticity) and harder than shells grown in control conditions. The outer shell (calcite) is more brittle in OA conditions while the inner shell (aragonite) is softer and less stiff in shells grown under OA conditions. Combining increasing ocean pCO2 and temperatures as projected for future global ocean appears to reduce the impact of increasing pCO2 on the material properties of the mussel shell. OA may cause changes in shell material properties that could prove problematic under predation scenarios for the mussels; however, this may be partially mitigated by increasing temperature.

  5. Thermophysical Properties of Automotive Metallic Brake Disk Materials

    Science.gov (United States)

    Kim, S. W.; Park, K.; Lee, S. H.; Kang, K. H.; Lim, K. T.

    2008-12-01

    The temperature distribution, the thermal deformation, and the thermal stress of automotive brake disks have quite close relations with car safety; therefore, much research in this field has been performed. However, successful and satisfactory results have not been obtained because the temperature-dependent thermophysical properties of brake disk materials are not sufficiently known. In this study, the thermophysical properties (thermal diffusivity, the specific heat, and the coefficient of thermal expansion) of three kinds of iron alloy series brake disk materials, FC250, FC170, and FCD50, and two kinds of aluminum alloy series brake disk materials, Al MMC and A356, were measured in the temperature range from room temperature to 500 °C, and the thermal conductivity was calculated using the measured thermal diffusivity, specific heat capacity, and density. As expected, the results show that the two series have significant differences in respect of the thermophysical properties, and to reduce the thermal deformation of the brake disk, the aluminum alloys with a high thermal conductivity and the iron alloys with low thermal expansion are recommended.

  6. Deciphering chemical order/disorder and material properties at the single-atom level.

    Science.gov (United States)

    Yang, Yongsoo; Chen, Chien-Chun; Scott, M C; Ophus, Colin; Xu, Rui; Pryor, Alan; Wu, Li; Sun, Fan; Theis, Wolfgang; Zhou, Jihan; Eisenbach, Markus; Kent, Paul R C; Sabirianov, Renat F; Zeng, Hao; Ercius, Peter; Miao, Jianwei

    2017-02-01

    Perfect crystals are rare in nature. Real materials often contain crystal defects and chemical order/disorder such as grain boundaries, dislocations, interfaces, surface reconstructions and point defects. Such disruption in periodicity strongly affects material properties and functionality. Despite rapid development of quantitative material characterization methods, correlating three-dimensional (3D) atomic arrangements of chemical order/disorder and crystal defects with material properties remains a challenge. On a parallel front, quantum mechanics calculations such as density functional theory (DFT) have progressed from the modelling of ideal bulk systems to modelling 'real' materials with dopants, dislocations, grain boundaries and interfaces; but these calculations rely heavily on average atomic models extracted from crystallography. To improve the predictive power of first-principles calculations, there is a pressing need to use atomic coordinates of real systems beyond average crystallographic measurements. Here we determine the 3D coordinates of 6,569 iron and 16,627 platinum atoms in an iron-platinum nanoparticle, and correlate chemical order/disorder and crystal defects with material properties at the single-atom level. We identify rich structural variety with unprecedented 3D detail including atomic composition, grain boundaries, anti-phase boundaries, anti-site point defects and swap defects. We show that the experimentally measured coordinates and chemical species with 22 picometre precision can be used as direct input for DFT calculations of material properties such as atomic spin and orbital magnetic moments and local magnetocrystalline anisotropy. This work combines 3D atomic structure determination of crystal defects with DFT calculations, which is expected to advance our understanding of structure-property relationships at the fundamental level.

  7. Deciphering chemical order/disorder and material properties at the single-atom level

    Science.gov (United States)

    Yang, Yongsoo; Chen, Chien-Chun; Scott, M. C.; Ophus, Colin; Xu, Rui; Pryor, Alan; Wu, Li; Sun, Fan; Theis, Wolfgang; Zhou, Jihan; Eisenbach, Markus; Kent, Paul R. C.; Sabirianov, Renat F.; Zeng, Hao; Ercius, Peter; Miao, Jianwei

    2017-02-01

    Perfect crystals are rare in nature. Real materials often contain crystal defects and chemical order/disorder such as grain boundaries, dislocations, interfaces, surface reconstructions and point defects. Such disruption in periodicity strongly affects material properties and functionality. Despite rapid development of quantitative material characterization methods, correlating three-dimensional (3D) atomic arrangements of chemical order/disorder and crystal defects with material properties remains a challenge. On a parallel front, quantum mechanics calculations such as density functional theory (DFT) have progressed from the modelling of ideal bulk systems to modelling ‘real’ materials with dopants, dislocations, grain boundaries and interfaces; but these calculations rely heavily on average atomic models extracted from crystallography. To improve the predictive power of first-principles calculations, there is a pressing need to use atomic coordinates of real systems beyond average crystallographic measurements. Here we determine the 3D coordinates of 6,569 iron and 16,627 platinum atoms in an iron-platinum nanoparticle, and correlate chemical order/disorder and crystal defects with material properties at the single-atom level. We identify rich structural variety with unprecedented 3D detail including atomic composition, grain boundaries, anti-phase boundaries, anti-site point defects and swap defects. We show that the experimentally measured coordinates and chemical species with 22 picometre precision can be used as direct input for DFT calculations of material properties such as atomic spin and orbital magnetic moments and local magnetocrystalline anisotropy. This work combines 3D atomic structure determination of crystal defects with DFT calculations, which is expected to advance our understanding of structure–property relationships at the fundamental level.

  8. Modelling of advanced structural materials for GEN IV reactors

    Science.gov (United States)

    Samaras, M.; Hoffelner, W.; Victoria, M.

    2007-09-01

    The choice of suitable materials and the assessment of long-term materials damage are key issues that need to be addressed for the safe and reliable performance of nuclear power plants. Operating conditions such as high temperatures, irradiation and a corrosive environment degrade materials properties, posing the risk of very expensive or even catastrophic plant damage. Materials scientists are faced with the scientific challenge to determine the long-term damage evolution of materials under service exposure in advanced plants. A higher confidence in life-time assessments of these materials requires an understanding of the related physical phenomena on a range of scales from the microscopic level of single defect damage effects all the way up to macroscopic effects. To overcome lengthy and expensive trial-and-error experiments, the multiscale modelling of materials behaviour is a promising tool, bringing new insights into the fundamental understanding of basic mechanisms. This paper presents the multiscale modelling methodology which is taking root internationally to address the issues of advanced structural materials for Gen IV reactors.

  9. Modeling ready biodegradability of fragrance materials.

    Science.gov (United States)

    Ceriani, Lidia; Papa, Ester; Kovarich, Simona; Boethling, Robert; Gramatica, Paola

    2015-06-01

    In the present study, quantitative structure activity relationships were developed for predicting ready biodegradability of approximately 200 heterogeneous fragrance materials. Two classification methods, classification and regression tree (CART) and k-nearest neighbors (kNN), were applied to perform the modeling. The models were validated with multiple external prediction sets, and the structural applicability domain was verified by the leverage approach. The best models had good sensitivity (internal ≥80%; external ≥68%), specificity (internal ≥80%; external 73%), and overall accuracy (≥75%). Results from the comparison with BIOWIN global models, based on group contribution method, show that specific models developed in the present study perform better in prediction than BIOWIN6, in particular for the correct classification of not readily biodegradable fragrance materials. © 2015 SETAC.

  10. Filter properties of seam material from paved urban soils

    Directory of Open Access Journals (Sweden)

    T. Nehls

    2007-08-01

    Full Text Available We studied pavement seam material. This is the soil substrate in joints of pervious pavements in urban areas. It is mostly 1 cm thick and develops from the original seam filling by depositions of all kinds of urban residues, including anthropogenic organic substances. It was investigated, how this unique form of organic matter influences the filter properties of seam material and how the seam material influences heavy metal transport through the pavement. The seam material is characterised by a darker munsell colour, higher organic carbon content, higher surface areas, higher cation exchange capacities, but a lower fraction of high adsorption energy sites compared to the original seam filling. The deposited anthropogenic organic matter itself could be characterised as particulate and non-polar. Compared to natural soils, it has a small surface area and a low surface charge density resulting in a small cation exchange capacity of only 75 cmol(+ kg−1C. The seam material shows stronger sorption of Pb and Cd compared to the original construction sand. The retardation capacity of seam material towards Pb is similar, towards Cd it is much smaller compared to natural soils. The simulated long term displacement scenarios for a street in Berlin do not indicate an acute contamination risk for Pb. For Cd the infiltration from ponds can lead to a displacement of Cd during only one decade.

  11. Material Properties of Wire for the Fabrication of Knotted Fences

    Directory of Open Access Journals (Sweden)

    Dirk J. Pons

    2014-01-01

    Full Text Available This paper describes the materials properties of galvanised fencing wire, as used in the fabrication of knotted wire fences. A range of physical properties are investigated: tensile strength, ductility in tension, Young’s modulus, three-point bending, and bending span. A range of commercially available wire products were tested. The results show that most, but not all, high tensile wire samples met the minimum tensile and ductility requirements. Young’s modulus results failed to provide any meaningful insights into wire quality. Flexural modulus results also failed to provide any insight into wire quality issues, with no statistically significant differences existing between acceptable and problematic wire batches. The implications are that premature fence failures are unlikely to be caused solely by reduced tensile properties. Existing test methods, including tensile strength and ductility, are somewhat incomplete, perhaps even unreliable, as measures of wire quality.

  12. Regional material properties of the human hip joint capsule ligaments.

    Science.gov (United States)

    Hewitt, J; Guilak, F; Glisson, R; Vail, T P

    2001-05-01

    The hip joint capsule functions to constrain translation between the femur and acetabulum while allowing rotational and planar movements. Despite the crucial role it plays in the pathogenesis of hip instability, little is known about its biomechanical properties. The goal of this study was to determine the regional material properties of the iliofemoral and ischiofemoral ligaments of the capsule. Ten human cadaveric specimens of each ligament were tested to failure in tension. The stress at failure, strain at failure, strain energy density at failure, toe- and linear-region elastic moduli, and the Poisson's ratio were measured for each ligament. The strain to failure was greatest in the ischiofemoral ligament, while no significant difference was noted in failure stress by region or ligament. The Young's moduli of elasticity ranged from 76.1 to 285.8 MPa among the different ligaments, and were generally consistent with properties previously reported for the shoulder capsule. The elastic moduli and strain energy density at failure differed by region. No significant differences in Poisson's ratio were found by region or ligament. The average Poisson's ratio was approximately 1.4, consistent with anisotropic behavior of ligamentous tissues. Understanding the material properties of the hip capsule may help the orthopaedic surgeon better understand normal ligament function, and thereby choose a surgical approach or strategy of repair. Furthermore, knowledge of the normal mechanical function of the hip capsule ligaments could assist in the evaluation of the success of a repair.

  13. Property predictions using microstructural modeling

    Energy Technology Data Exchange (ETDEWEB)

    Wang, K.G. [Department of Materials Science and Engineering, Rensselaer Polytechnic Institute, CII 9219, 110 8th Street, Troy, NY 12180-3590 (United States)]. E-mail: wangk2@rpi.edu; Guo, Z. [Sente Software Ltd., Surrey Technology Centre, 40 Occam Road, Guildford GU2 7YG (United Kingdom); Sha, W. [Metals Research Group, School of Civil Engineering, Architecture and Planning, The Queen' s University of Belfast, Belfast BT7 1NN (United Kingdom); Glicksman, M.E. [Department of Materials Science and Engineering, Rensselaer Polytechnic Institute, CII 9219, 110 8th Street, Troy, NY 12180-3590 (United States); Rajan, K. [Department of Materials Science and Engineering, Rensselaer Polytechnic Institute, CII 9219, 110 8th Street, Troy, NY 12180-3590 (United States)

    2005-07-15

    Precipitation hardening in an Fe-12Ni-6Mn maraging steel during overaging is quantified. First, applying our recent kinetic model of coarsening [Phys. Rev. E, 69 (2004) 061507], and incorporating the Ashby-Orowan relationship, we link quantifiable aspects of the microstructures of these steels to their mechanical properties, including especially the hardness. Specifically, hardness measurements allow calculation of the precipitate size as a function of time and temperature through the Ashby-Orowan relationship. Second, calculated precipitate sizes and thermodynamic data determined with Thermo-Calc[copyright] are used with our recent kinetic coarsening model to extract diffusion coefficients during overaging from hardness measurements. Finally, employing more accurate diffusion parameters, we determined the hardness of these alloys independently from theory, and found agreement with experimental hardness data. Diffusion coefficients determined during overaging of these steels are notably higher than those found during the aging - an observation suggesting that precipitate growth during aging and precipitate coarsening during overaging are not controlled by the same diffusion mechanism.

  14. Static Magnetic Properties of AL800 Garnet Material

    Energy Technology Data Exchange (ETDEWEB)

    Kuharik, J. [Fermilab; Madrak, R. [Fermilab; Makarov, A. [Fermilab; Pellico, W. [Fermilab; Sun, S. [Fermilab; Tan, C. Y. [Fermilab; Terechkine, I. [Fermilab

    2017-05-17

    A second harmonic tunable RF cavity is being devel-oped for the Fermilab Booster. This device, which prom-ises reduction of the particle beam loss at the injection, transition, and extraction stages, employs perpendicularly biased garnet material for frequency tuning. The required range of the tuning is significantly wider than in previously built and tested tunable RF devices. As a result, the mag-netic field in the garnet comes fairly close to the gyromag-netic resonance line at the lower end of the frequency range. The chosen design concept of a tuner for the cavity cannot ensure uniform magnetic field in the garnet mate-rial; thus, it is important to know the static magnetic prop-erties of the material to avoid significant increase in the lo-cal RF loss power density. This report summarizes studies performed at Fermilab to understand variations in the mag-netic properties of the AL800 garnet material used to build the tuner of the cavity.

  15. A Sorption Hysteresis Model For Cellulosic Materials

    DEFF Research Database (Denmark)

    Frandsen, Henrik Lund; Damkilde, Lars

    2006-01-01

    The equilibrium concentration of adsorbed water in cellulosic materials is dependent on the history of the variations of vapor pressure in the ambient air, i.e. sorption hysteresis. Existing models to describe this phenomenon such as the independent domain theory have numerical drawbacks and....../or imply accounting for the entire history variations of every material point. This paper presents a sorption hysteresis model based on a state formulation and expressed in closed-form solutions, which makes it suitable for implementation into a numerical method....

  16. Effect of Spraying Condition and Material Properties on the Residual Stress in Plasma Spraying

    Institute of Scientific and Technical Information of China (English)

    Xiancheng ZHANG; Jianming GONG; Shandong TU

    2004-01-01

    The thermomechanical behavior and the distribution of residual stresses due to thermal spraying of NiCoCrAIY coating were studied by thermomechanical finite dement analysis. The effects of phase transformation due to solidifying process of coating particles, thickness and material properties of coating on the residual stresses were discussed.Results showed that residual stress decreases little with the stress relaxation due to the phase transformation. For the substrates with the same thickness, the residual stress increases with the increase in coating thickness. The state of residual stresses relates to the material properties of coating and substrate closely. The stress-induced failure model of coating is also discussed.

  17. An elastic mechanics model and computation method for geotechnical material

    Institute of Scientific and Technical Information of China (English)

    Zheng Yingren; Gao Hong; Zheng Lushi

    2010-01-01

    Internal friction characteristic is one of the basic properties of geotechnical materials and it exists in mechanical elements all the time.However,until now internal friction is only considered in limit analysis and plastic mechanics but not included in elastic theory for rocks and soils.We consider that internal friction exists in both elastic state and plastic state of geotechnical materials,so the mechanical unit of friction material is constituted.Based on study results of soil tests,the paper also proposes that cohesion takes effect first and internal friction works gradually with the increment of deformation.By assuming that the friction coefficient is proportional to the strain,the internal friction is computed.At last,by imitating the linear elastic mechanics,the nonlinear elastic mechanics model of friction material is established,where the shear modulus G is not a constant.The new model and the traditional elastic model are used simultaneously to analyze an elastic foundation.The results indicate that the displacements computed by the new model are less than those from the traditional method,which agrees with the fact and shows that the mechanical units of friction material are suitable for geotechnical material.

  18. Modelling of structure and mechanics of materials from microscale to product

    Energy Technology Data Exchange (ETDEWEB)

    Carstensen, J.V.; Leffers, T.; Lorentzen, T.; Pedersen, O.B.; Soerensen, B.F.; Winther, G. [eds.

    1998-12-31

    The theme of this symposium is the relation between the processing, structure and mechanical behaviour of materials and its expression in analytical and numerical models. Structure-property relations inevitably involve different length scales. Ultimately the scales range from the macroscopic to the atomic level corresponding to the ultimate resolution of the characterisation methods. The technologically interesting properties of many new materials are determined by structural features of nanometer size. Also, the size of modern industrial components ranges down to dimensions comparable with the scale of materials microstructures. The symposium focuses on attempts to establish connections between the various length scales. Research along these lines involves four different disciplines: materials processing, materials mechanics, materials science and materials physics. Traditionally, there are gaps between the various disciplines, particularly between the continuum models of materials processing and materials mechanics and the atomic models of materials physics. It is our ambition that the symposium will contribute to the narrowing of these gaps. (au)

  19. Preparation and properties on hollow nano-structured smoke material

    Science.gov (United States)

    Liu, Xiang-cui; Dai, Meng-yan; Fang, Guo-feng; Shi, Wei-dong; Cheng, Xiang; Liu, Hai-feng; Zhang, Tong

    2013-09-01

    In recent years, the weapon systems of laser guidance and infrared (IR) imaging guidance have been widely used in modern warfare because of their high precision and strong anti-interference. Notwithstanding, military smoke, as a rapid and effective passive jamming means, can effectively counteract the attack of enemy precision-guided weapons by scattering and absorbability. Conventional smoke has good attenuation capability only to visible light (0.4-0.76 μm), but hardly any effect to other electromagnetic wave band. The weapon systems of laser guidance and IR imaging guidance usually work in broad band, including near IR (1-3 μm), middle IR (3-5 μm), far IR (8-14 μm), and so on. Accordingly, exploiting and using new efficient obscurant materials, which is one of the important factors that develop smoke technology, have become a focus and attracted more interests around the world. Then nano-structured materials that are developing very quickly have turned into our new choice. Hollow nano-structured materials (HNSM) have many special properties because of their nano-size wall-thickness and sub-micron grain-size. After a lot of HNSM were synthesized in this paper, their physical and chemical properties, including grain size, phase composition, microstructure, optical properties and resistivity were tested and analysed. Then the experimental results of the optical properties showed that HNSM exhibit excellent wave-absorbing ability in ultraviolet, visible and infrared regions. On the basis of the physicochemmical properties, HNSM are firstly applied in smoke technology field. And the obscuration performance of HNSM smoke was tested in smoke chamber. The testing waveband included 1.06μm and 10.6μm laser, 3-5μm and 8-14μm IR radiation. Then the main parameters were obtained, including the attenuation rate, the transmission rate, the mass extinction coefficient, the efficiency obscuring time, and the sedimentation rate, etc. The main parameters of HNSM smoke were

  20. New resource for the computation of cartilage biphasic material properties with the interpolant response surface method.

    Science.gov (United States)

    Keenan, Kathryn E; Kourtis, Lampros C; Besier, Thor F; Lindsey, Derek P; Gold, Garry E; Delp, Scott L; Beaupre, Gary S

    2009-08-01

    Cartilage material properties are important for understanding joint function and diseases, but can be challenging to obtain. Three biphasic material properties (aggregate modulus, Poisson's ratio and permeability) can be determined using an analytical or finite element model combined with optimisation to find the material properties values that best reproduce an experimental creep curve. The purpose of this study was to develop an easy-to-use resource to determine biphasic cartilage material properties. A Cartilage Interpolant Response Surface was generated from interpolation of finite element simulations of creep indentation tests. Creep indentation tests were performed on five sites across a tibial plateau. A least-squares residual search of the Cartilage Interpolant Response Surface resulted in a best-fit curve for each experimental condition with corresponding material properties. These sites provided a representative range of aggregate moduli (0.48-1.58 MPa), Poisson's ratio (0.00-0.05) and permeability (1.7 x 10(- 15)-5.4 x 10(- 15) m(4)/N s) values found in human cartilage. The resource is freely available from https://simtk.org/home/va-squish.

  1. Modeling and Simulation of Nuclear Fuel Materials

    Energy Technology Data Exchange (ETDEWEB)

    Devanathan, Ramaswami; Van Brutzel, Laurent; Chartier, Alan; Gueneau, Christine; Mattsson, Ann E.; Tikare, Veena; Bartel, Timothy; Besmann, T. M.; Stan, Marius; Van Uffelen, Paul

    2010-10-01

    We review the state of modeling and simulation of nuclear fuels with emphasis on the most widely used nuclear fuel, UO2. The hierarchical scheme presented represents a science-based approach to modeling nuclear fuels by progressively passing information in several stages from ab initio to continuum levels. Such an approach is essential to overcome the challenges posed by radioactive materials handling, experimental limitations in modeling extreme conditions and accident scenarios, and the small time and distance scales of fundamental defect processes. When used in conjunction with experimental validation, this multiscale modeling scheme can provide valuable guidance to development of fuel for advanced reactors to meet rising global energy demand.

  2. Thermodynamic and kinetic modelling: creep resistant materials

    DEFF Research Database (Denmark)

    Hald, John; Korcakova, L.; Danielsen, Hilmar Kjartansson

    2008-01-01

    particles and coarsening of MX, M23C6 and Laves phase particles. The modelling provided new insight into the long term stability of new steels. Modelling of the detrimental precipitation of Z phase Cr(V,Nb)N is described, which points to new approaches in alloy development for higher temperatures......The use of thermodynamic and kinetic modelling of microstructure evolution in materials exposed to high temperatures in power plants is demonstrated with two examples. Precipitate stability in martensitic 9–12%Cr steels is modelled including equilibrium phase stability, growth of Laves phase...

  3. A continuum damage model for piezoelectric materials

    Institute of Scientific and Technical Information of China (English)

    Yiming Fu; Xianqiao Wang

    2008-01-01

    In this paper, a constitutive model is proposed for piezoelectric material solids containing distributed cracks.The model is formulated in a framework of continuum damage mechanics using second rank tensors as internal variables. The Helmhotlz free energy of piezoelectric mate-rials with damage is then expressed as a polynomial including the transformed strains, the electric field vector and the ten-sorial damage variables by using the integrity bases restricted by the initial orthotropic symmetry of the material. By using the Talreja's tensor valued internal state damage variables as well as the Helmhotlz free energy of the piezoelectric mate-rial, the constitutive relations of piezoelectric materials with damage are derived. The model is applied to a special case of piezoelectric plate with transverse matrix cracks. With theKirchhoff hypothesis of plate, the free vibration equationsof the piezoelectric rectangular plate considering damage isestablished. By using Galerkin method, the equations are sol-ved. Numerical results show the effect of the damage on the free vibration of the piezoelectric plate under the close-circuit condition, and the present results are compared with those of the three-dimensional theory.

  4. Scanning Probe Evaluation of Electronic, Mechanical and Structural Material Properties

    Science.gov (United States)

    Virwani, Kumar

    2011-03-01

    We present atomic force microscopy (AFM) studies of a range of properties from three different classes of materials: mixed ionic electronic conductors, low-k dielectrics, and polymer-coated magnetic nanoparticles. (1) Mixed ionic electronic conductors are being investigated as novel diodes to drive phase-change memory elements. Their current-voltage characteristics are measured with direct-current and pulsed-mode conductive AFM (C-AFM). The challenges to reliability of the C-AFM method include the electrical integrity of the probe, the sample and the contacts, and the minimization of path capacitance. The role of C-AFM in the optimization of these electro-active materials will be presented. (2) Low dielectric constant (low-k) materials are used in microprocessors as interlayer insulators, a role directly affected by their mechanical performance. The mechanical properties of nanoporous silicate low-k thin films are investigated in a comparative study of nanomechanics measured by AFM and by traditional nanoindentation. Both methods are still undergoing refinement as reliable analytical tools for determining nanomechanical properties. We will focus on AFM, the faster of the two methods, and its developmental challenges of probe shape, cantilever force constant, machine compliance and calibration standards. (3) Magnetic nanoparticles are being explored for their use in patterned media for magnetic storage. Current methods for visualizing the core-shell structure of polymer-coated magnetic nanoparticles include dye-staining the polymer shell to provide contrast in transmission electron microscopy. AFM-based fast force-volume measurements provide direct visualization of the hard metal oxide core within the soft polymer shell based on structural property differences. In particular, the monitoring of adhesion and deformation between the AFM tip and the nanoparticle, particle-by-particle, provides a reliable qualitative tool to visualize core-shell contrast without the use

  5. Testing and modeling of rockfill materials:A review

    Institute of Scientific and Technical Information of China (English)

    Yang Xiao; Hong Liu; Wengang Zhang; Hanlong Liu; Feng Yin; Youyu Wang

    2016-01-01

    The research development of rockfill materials (RFM) was investigated by a series of large-scale triaxial tests. It is observed that confining pressure and particle breakage play important roles in the mechanical property, dilatancy relation and constitutive model of RFM. In addition, it is observed that the conven-tional dilatancy relation and constitutive model are not suitable for RFM due to the complex mechanical behavior. Hence, it needs to propose a unified constitutive model of RFM, considering the state-dependent and particle breakage behavior.

  6. Numerical determination of the material properties of porous dust cakes

    CERN Document Server

    Paszun, D

    2008-01-01

    The formation of planetesimals requires the growth of dust particles through collisions. Micron-sized particles must grow by many orders of magnitude in mass. In order to understand and model the processes during this growth, the mechanical properties, and the interaction cross sections of aggregates with surrounding gas must be well understood. Recent advances in experimental (laboratory) studies now provide the background for pushing numerical aggregate models onto a new level. We present the calibration of a previously tested model of aggregate dynamics. We use plastic deformation of surface asperities as the physical model to bring critical velocities for sticking into accordance with experimental results. The modified code is then used to compute compression strength and the velocity of sound in the aggregate at different densities. We compare these predictions with experimental results and conclude that the new code is capable of studying the properties of small aggregates.

  7. Synthesis, processing and properties of materials for SOFCs

    Energy Technology Data Exchange (ETDEWEB)

    Bates, J.L.; Armstrong, T.A.; Kingsley, J.J.; Pederson, L.R.

    1994-03-01

    The synthesis and processing methods of complex oxide materials can significantly influence use in solid oxide fuel cells (SOFCs). This paper discusses (1) effects of powder synthesis and conditioning on fabrication, i.e., sintering, where close, reproducible control of composition and structure are required, and (2) influences on electrical, mechanical, structural and electrochemical properties that can influence SOFC performance. Examples are given for chromites, manganites and related oxides used as interconnections and electrodes in SOFCs. Materials, from source to incorporation into the fuel cell and generator, is a major issue in the development of solid oxide fuel cells (SOFCs). An integral part of this is the synthesis from chemicals and other virgin materials, generally as an oxide or metal powder, which can become a SOFC component. In some instances, such as with electrochemical vapor deposition, the component is formed directly from the chemicals. The synthesized materials are then conditioned and processes prior to fabrication into the fuel cell component, either separately or in conjunction with other material components.

  8. Cellular Automata Model for Elastic Solid Material

    Institute of Scientific and Technical Information of China (English)

    DONG Yin-Feng; ZHANG Guang-Cai; XU Ai-Guo; GAN Yan-Biao

    2013-01-01

    The Cellular Automaton (CA) modeling and simulation of solid dynamics is a long-standing difficult problem.In this paper we present a new two-dimensional CA model for solid dynamics.In this model the solid body is represented by a set of white and black particles alternatively positioned in the x-and y-directions.The force acting on each particle is represented by the linear summation of relative displacements of the nearest-neighboring particles.The key technique in this new model is the construction of eight coefficient matrices.Theoretical and numerical analyses show that the present model can be mathematically described by a conservative system.So,it works for elastic material.In the continuum limit the CA model recovers the well-known Navier equation.The coefficient matrices are related to the shear module and Poisson ratio of the material body.Compared with previous CA model for solid body,this model realizes the natural coupling of deformations in the x-and y-directions.Consequently,the wave phenomena related to the Poisson ratio effects are successfully recovered.This work advances significantly the CA modeling and simulation in the field of computational solid dynamics.

  9. Modelling irradiation effects in fusion materials

    DEFF Research Database (Denmark)

    Victoria, M.; Dudarev, S.; Boutard, J.L.;

    2007-01-01

    We review the current status of the European fusion materials modelling programme. We describe recent findings and outline potential areas for future development. Large-scale density functional theory (DFT) calculations reveal the structure of the point defects in α-Fe, and highlight the crucial...

  10. A Sorption Hysteresis Model For Cellulosic Materials

    DEFF Research Database (Denmark)

    Frandsen, Henrik Lund; Damkilde, Lars

    2006-01-01

    The equilibrium concentration of adsorbed water in cellulosic materials is dependent on the history of the variations of vapor pressure in the ambient air, i.e. sorption hysteresis. Existing models to describe this phenomenon such as the independent domain theory have numerical drawbacks and/or i...

  11. Properties of Residue from Olive Oil Extraction as a Raw Material for Sustainable Construction Materials. Part I: Physical Properties

    Directory of Open Access Journals (Sweden)

    Almudena Díaz-García

    2017-01-01

    Full Text Available Action on climate, the environment, and the efficient use of raw materials and resources are important challenges facing our society. Against this backdrop, the construction industry must adapt to new trends and environmentally sustainable construction systems, thus requiring lines of research aimed at keeping energy consumption in new buildings as low as possible. One of the main goals of this research is to efficiently contribute to reducing the amount of residue from olive oil extraction using a two-phase method. This can be achieved by producing alternative structural materials to be used in the construction industry by means of a circular economy. The technical feasibility of adding said residue to ceramic paste was proven by analyzing the changes produced in the physical properties of the paste, which were then compared to the properties of the reference materials manufactured with clay without residue. Results obtained show that the heating value of wet pomace can contribute to the thermal needs of the sintering process, contributing 30% of energy in pieces containing 3% of said material. Likewise, adding larger amounts of wet pomace to the clay body causes a significant decrease in bulk density values.

  12. Constitutive modeling for isotropic materials (HOST)

    Science.gov (United States)

    Chan, Kwai S.; Lindholm, Ulric S.; Bodner, S. R.; Hill, Jeff T.; Weber, R. M.; Meyer, T. G.

    1986-01-01

    The results of the third year of work on a program which is part of the NASA Hot Section Technology program (HOST) are presented. The goals of this program are: (1) the development of unified constitutive models for rate dependent isotropic materials; and (2) the demonstration of the use of unified models in structural analyses of hot section components of gas turbine engines. The unified models selected for development and evaluation are those of Bodner-Partom and of Walker. A test procedure was developed for assisting the generation of a data base for the Bodner-Partom model using a relatively small number of specimens. This test procedure involved performing a tensile test at a temperature of interest that involves a succession of strain-rate changes. The results for B1900+Hf indicate that material constants related to hardening and thermal recovery can be obtained on the basis of such a procedure. Strain aging, thermal recovery, and unexpected material variations, however, preluded an accurate determination of the strain-rate sensitivity parameter is this exercise. The effects of casting grain size on the constitutive behavior of B1900+Hf were studied and no particular grain size effect was observed. A systematic procedure was also developed for determining the material constants in the Bodner-Partom model. Both the new test procedure and the method for determining material constants were applied to the alternate material, Mar-M247 . Test data including tensile, creep, cyclic and nonproportional biaxial (tension/torsion) loading were collected. Good correlations were obtained between the Bodner-Partom model and experiments. A literature survey was conducted to assess the effects of thermal history on the constitutive behavior of metals. Thermal history effects are expected to be present at temperature regimes where strain aging and change of microstructure are important. Possible modifications to the Bodner-Partom model to account for these effects are outlined

  13. Modeling of rheological properties for entangled polymer systems

    Science.gov (United States)

    Banerjee, Nilanjana

    The study of entangled polymer rheology both in the field of medicine and polymer processing has their major importance. Mechanical properties of biomolecules are studied in order to better understand cellular behavior. Similarly, industrial processing of polymers needs thorough understanding of rheology so as to improve process techniques. Work in this dissertation has been organized into three major sections. Firstly, numerical/analytical models are reviewed for describing rheological properties and mechanical behaviors of cytoskeleton. The cytoskeleton models are classified into categories according to the length scales of the phenomena of interest. The main principles and characteristics of each model are summarized and discussed by comparison with each other, thus providing a systematic understanding of biopolymer network modeling. Secondly, a new constitutive "toy" Mead-Banerjee-Park (MBP) model is developed for monodisperse entangled polymer systems, by introducing the idea of a configuration dependent friction coefficient (CDFC) and entanglement dynamics (ED) into the MLD "toy" model. The model is tested against experimental data in steady and transient extensional and shear flows. The model simultaneously captures the monotonic thinning of the extensional flow curve of polystyrene (PS) melts and the extension hardening found in PS solutions. Thirdly, the monodisperse MBP model is accordingly modified into polydisperse MBP "toy" constitutive model to predict the nonlinear viscoelastic material properties of model polydisperse systems. The polydisperse MBP toy model accurately predicts the material properties in the forward direction for transient uniaxial extension and transient shear flow.

  14. Mathematical modeling and stochastic simulation of soft materials

    Science.gov (United States)

    Zeng, Yun

    Soft materials are all around us; they may appear as consumer products, foods, or biological materials. The interest in studying the properties of soft materials both experimentally and theoretically has steadily increased due to their wide range of industrial applications. One example of a soft material is wormlike micellar solutions. Depending on the temperature and composition, these solvent-surfactant-salt mixtures may exhibit close to mono-exponential or, alternatively, power-law or stretched-exponential stress decay. Of particular interest to this thesis is the development of stochastic models that can capture the stress relaxation behavior of such materials in the small strain limit, which is non-exponential in time as opposed to exponential. Continuous time random walk (CTRW) or subordinated Langevin processes are utilized to model systems exhibiting non-exponential relaxation behavior or anomalous diffusion. Stochastic simulations using the CTRW approach or the subordination method are carried out in this thesis for one-dimensional systems in which the probability density distribution of particle positions is described by a fractional Fokker-Planck equation (FFPE). The equivalence of the CTRW simulation and the subordination simulation with that of the FFPE is analyzed through the simulation of an ensemble of particle trajectories. The simulated particle dynamics suggest that CTRW processes or subordinated Langevin dynamics can be included in soft material mesoscale dynamics to capture the anomalous transport. To model the non-exponential stress relaxation dynamics of soft gel systems (three-dimensional fluids), stochastic models are simulated using transient network theory as developed and combined with the CTRW and subordinated Langevin processes. This approach enables us to connect the microstructural dynamics of certain soft gel-like materials with macroscale experimental observations by examining the material properties under homogeneous shear flow

  15. Multiscale mechanics of hierarchical structure/property relationships in calcified tissues and tissue/material interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Katz, J. Lawrence [School of Computing and Engineering, University of Missouri-Kansas City, Kansas City, MO (United States) and School of Dentistry, University of Missouri-Kansas City, Kansas City, MO (United States)]. E-mail: katzjl@umkc.edu; Misra, Anil [School of Computing and Engineering, University of Missouri-Kansas City, Kansas City, MO (United States); Spencer, Paulette [School of Dentistry, University of Missouri-Kansas City, Kansas City, MO (United States); Wang, Yong [School of Dentistry, University of Missouri-Kansas City, Kansas City, MO (United States); Bumrerraj, Sauwanan [School of Medicine, Khon Kaen University, Khon Kaen (Thailand); Nomura, Tsutomu [School of Dentistry, Niigata University, Niigata (Japan); Eppell, Steven J. [Case School of Engineering, Case Western Reserve University, Cleveland, OH (United States); Tabib-Azar, Massood [Case School of Engineering, Case Western Reserve University, Cleveland, OH (United States)

    2007-04-15

    This paper presents a review plus new data that describes the role hierarchical nanostructural properties play in developing an understanding of the effect of scale on the material properties (chemical, elastic and electrical) of calcified tissues as well as the interfaces that form between such tissues and biomaterials. Both nanostructural and microstructural properties will be considered starting with the size and shape of the apatitic mineralites in both young and mature bovine bone. Microstructural properties for human dentin and cortical and trabecular bone will be considered. These separate sets of data will be combined mathematically to advance the effects of scale on the modeling of these tissues and the tissue/biomaterial interfaces as hierarchical material/structural composites. Interfacial structure and properties to be considered in greatest detail will be that of the dentin/adhesive (d/a) interface, which presents a clear example of examining all three material properties, (chemical, elastic and electrical). In this case, finite element modeling (FEA) was based on the actual measured values of the structure and elastic properties of the materials comprising the d/a interface; this combination provides insight into factors and mechanisms that contribute to premature failure of dental composite fillings. At present, there are more elastic property data obtained by microstructural measurements, especially high frequency ultrasonic wave propagation (UWP) and scanning acoustic microscopy (SAM) techniques. However, atomic force microscopy (AFM) and nanoindentation (NI) of cortical and trabecular bone and the dentin-enamel junction (DEJ) among others have become available allowing correlation of the nanostructural level measurements with those made on the microstructural level.

  16. Tooth and bone deformation: structure and material properties by ESPI

    Science.gov (United States)

    Zaslansky, Paul; Shahar, Ron; Barak, Meir M.; Friesem, Asher A.; Weiner, Steve

    2006-08-01

    In order to understand complex-hierarchical biomaterials such as bones and teeth, it is necessary to relate their structure and mechanical-properties. We have adapted electronic speckle pattern-correlation interferometry (ESPI) to make measurements of deformation of small water-immersed specimens of teeth and bones. By combining full-field ESPI with precision mechanical loading we mapped sub-micron displacements and determined material-properties of the samples. By gradually and elastically compressing the samples, we compensate for poor S/N-ratios and displacement differences of about 100nm were reliably determined along samples just 2~3mm long. We produced stress-strain curves well within the elastic performance range of these materials under biologically relevant conditions. For human tooth-dentin, Young's modulus in inter-dental areas of the root is 40% higher than on the outer sides. For cubic equine bone samples the compression modulus of axial orientations is about double the modulus of radial and tangential orientations (20 GPa versus 10 GPa respectively). Furthermore, we measured and reproduced a surprisingly low Poisson's ratio, which averaged about 0.1. Thus the non-contact and non-destructive measurements by ESPI produce high sensitivity analyses of mechanical properties of mineralized tissues. This paves the way for mapping deformation-differences of various regions of bones, teeth and other biomaterials.

  17. Materials Selection, Synthesis, and Dielectrical Properties of PVC Nanocomposites

    Directory of Open Access Journals (Sweden)

    Youssef Mobarak

    2013-01-01

    Full Text Available Materials selection process for electrical insulation application was carried out using Cambridge Engineering Selector (CES program. Melt mixing technique was applied to prepare polyvinyl-chloride- (PVC- nanofumed silica and nanomontmorillonite clay composites. Surface analysis and particles dispersibility were examined using scanning electron microscope. Dielectrical properties were assessed using Hipot tester. An experimental work for dielectric loss of the nanocomposite materials has been investigated in a frequency range of 10 Hz–50 kHz. The initial results using CES program showed that microparticles of silica and clay can improve electrical insulation properties and modulus of elasticity of PVC. Nano-montmorillonite clay composites were synthesized and characterized. Experimental analyses displayed that trapping properties of matrix are highly modified by the presence of nanofillers. The nanofumed silica and nanoclay particles were dispersed homogenously in PVC up to 10% wt/wt. Dielectric loss tangent constant of PVC-nanoclay composites was decreased successfully from 0.57 to 0.5 at 100 Hz using fillers loading from 1% to 10% wt/wt, respectively. Nano-fumed silica showed a significant influence on the electrical resistivity of PVC by enhancing it up to 1 × 1011 Ohm·m.

  18. Oxide Thermoelectric Materials: A Structure-Property Relationship

    Science.gov (United States)

    Nag, Abanti; Shubha, V.

    2014-04-01

    Recent demand for thermoelectric materials for power harvesting from automobile and industrial waste heat requires oxide materials because of their potential advantages over intermetallic alloys in terms of chemical and thermal stability at high temperatures. Achievement of thermoelectric figure of merit equivalent to unity ( ZT ≈ 1) for transition-metal oxides necessitates a second look at the fundamental theory on the basis of the structure-property relationship giving rise to electron correlation accompanied by spin fluctuation. Promising transition-metal oxides based on wide-bandgap semiconductors, perovskite and layered oxides have been studied as potential candidate n- and p-type materials. This paper reviews the correlation between the crystal structure and thermoelectric properties of transition-metal oxides. The crystal-site-dependent electronic configuration and spin degeneracy to control the thermopower and electron-phonon interaction leading to polaron hopping to control electrical conductivity is discussed. Crystal structure tailoring leading to phonon scattering at interfaces and nanograin domains to achieve low thermal conductivity is also highlighted.

  19. The Study of the Thermoelectric Properties of Phase Change Materials

    Science.gov (United States)

    Yin, Ming; Abdi, Mohammed; Noimande, Zibusisu; Mbamalu, Godwin; Alameeri, Dheyaa; Datta, Timir

    We study thermoelectric property that is electrical phenomena occurring in conjunction with the flow of heat of phase-change materials (PCM) in particular GeSbTe (GST225). From given sets of material parameters, COMSOL Multiphysics heat-transfer module is used to compute maps of temperature and voltage distribution in the PCM samples. These results are used to design an apparatus including the variable temperature sample holder set up. An Arbitrary/ Function generator and a circuit setup is also designed to control the alternation of heaters embedded on the sample holder in order to ensure sequential back and forward flow of heat current from both sides of the sample. Accurate values of potential differences and temperature distribution profiles are obtained in order to compute the Seebeck coefficient of the sample. The results of elemental analysis and imaging studies such as XRD, UV-VIS, EDEX and SEM of the sample are obtained. Factors affecting the thermoelectric properties of phase change memory are also discussed. NNSA/ DOD Consortium for Materials and Energy Studies.

  20. Modeling of space environment impact on nanostructured materials. General principles

    Science.gov (United States)

    Voronina, Ekaterina; Novikov, Lev

    2016-07-01

    In accordance with the resolution of ISO TC20/SC14 WG4/WG6 joint meeting, Technical Specification (TS) 'Modeling of space environment impact on nanostructured materials. General principles' which describes computer simulation methods of space environment impact on nanostructured materials is being prepared. Nanomaterials surpass traditional materials for space applications in many aspects due to their unique properties associated with nanoscale size of their constituents. This superiority in mechanical, thermal, electrical and optical properties will evidently inspire a wide range of applications in the next generation spacecraft intended for the long-term (~15-20 years) operation in near-Earth orbits and the automatic and manned interplanetary missions. Currently, ISO activity on developing standards concerning different issues of nanomaterials manufacturing and applications is high enough. Most such standards are related to production and characterization of nanostructures, however there is no ISO documents concerning nanomaterials behavior in different environmental conditions, including the space environment. The given TS deals with the peculiarities of the space environment impact on nanostructured materials (i.e. materials with structured objects which size in at least one dimension lies within 1-100 nm). The basic purpose of the document is the general description of the methodology of applying computer simulation methods which relate to different space and time scale to modeling processes occurring in nanostructured materials under the space environment impact. This document will emphasize the necessity of applying multiscale simulation approach and present the recommendations for the choice of the most appropriate methods (or a group of methods) for computer modeling of various processes that can occur in nanostructured materials under the influence of different space environment components. In addition, TS includes the description of possible

  1. A nonlinear constitutive model for magnetostrictive materials

    Institute of Scientific and Technical Information of China (English)

    Xin'en Liu; Xiaojing Zheng

    2005-01-01

    A general nonlinear constitutive model is proposed for magnetostrictive materials, based on the important physical fact that a nonlinear part of the elastic strain produced by a pre-stress is related to the magnetic domain rotation or movement and is responsible for the change of the maximum magnetostrictive strain with the pre-stress. To avoid the complicity of determining the tensor function describing the nonlinear elastic strain part, this paper proposes a simplified model by means of linearizing the nonlinear function.For the convenience of engineering applications, the expressions of the 3-D (bulk), 2-D (film) and 1-D (rod) models are, respectively, given for an isotropic material and their applicable ranges are also discussed. By comparison with the experimental data of a Terfenol-D rod, it is found that the proposed model can accurately predict the magnetostrictive strain curves in low, moderate and high magnetic field regions for various compressive pre-stress levels. The numerical simulation further illustrates that, for either magnetostrictive rods or thin films, the proposed model can effectively describe the effects of the pre-stress or residual stress on the magnetization and magnetostrictive strain curves, while none of the known models can capture all of them. Therefore, the proposed model enjoys higher precision and wider applicability than the previous models, especially in the region of the high field.

  2. A Hysteresis Model for Piezoceramic Materials

    Science.gov (United States)

    Smith, Ralph C.; Ounaies, Zoubeida

    1999-01-01

    This paper addresses the modeling of nonlinear constitutive relations and hysteresis inherent to piezoceramic materials at moderate to high drive levels. Such models are, necessary to realize the, full potential of the materials in high performance control applications, and a necessary prerequisite is the development of techniques which permit control implementation. The approach employed here is based on the qualification of reversible and irreversible domain wall motion in response to applied electric fields. A comparison with experimental data illustrates that because the resulting ODE model is physics-based, it can be employed for both characterization and prediction of polarization levels throughout the range of actuator operation. Finally, the ODE formulation is amenable to inversion which facilitates the development of an inverse compensator for linear control design.

  3. Molecular structure based property modeling: Development/ improvement of property models through a systematic property-data-model analysis

    DEFF Research Database (Denmark)

    Hukkerikar, Amol Shivajirao; Sarup, Bent; Sin, Gürkan

    2013-01-01

    models. To make the property-data-model analysis fast and efficient, an approach based on the “molecular structure similarity criteria” to identify molecules (mono-functional, bi-functional, etc.) containing specified set of structural parameters (that is, groups) is employed. The method has been applied...... to a wide range of properties of pure compounds. In this work, however, the application of the method is illustrated for the property modeling of normal melting point, enthalpy of fusion, enthalpy of formation, and critical temperature. For all the properties listed above, it has been possible to achieve...

  4. Modeling Non-Linear Material Properties in Composite Materials

    Science.gov (United States)

    2016-06-28

    will be used to calculate the thermal strains. In equation [6], α is the coefficient of thermal expansion tensor . To determine the effects of the...governing equation for the microscale, where I is the identity tensor and Hk(y) is a Y-periodic tensor on the micro- scale relating T1 to the macro...9c] is the governing equation for the global scale. In this equation, � represents the effective thermal conductivity tensor , � is the

  5. Diffusion in condensed matter methods, materials, models

    CERN Document Server

    Kärger, Jörg

    2005-01-01

    Diffusion as the process of particle transport due to stochastic movement is a phenomenon of crucial relevance for a large variety of processes and materials. This comprehensive, handbook- style survey of diffusion in condensed matter gives detailed insight into diffusion as the process of particle transport due to stochastic movement. Leading experts in the field describe in 23 chapters the different aspects of diffusion, covering microscopic and macroscopic experimental techniques and exemplary results for various classes of solids, liquids and interfaces as well as several theoretical concepts and models. Students and scientists in physics, chemistry, materials science, and biology will benefit from this detailed compilation.

  6. Magnetomechanical Properties Of Composite Materials With Giant Magnetostriction

    Directory of Open Access Journals (Sweden)

    Tomiczek A.E.

    2015-09-01

    Full Text Available The aim of this work was to observe the changes in the magnetomechanical properties of composite materials with different Tb0.3Dy0.7Fe1.9 (Terfenol-D powder particle-size distributions and varying volume fractions in the polyurethane matrix. The results show a direct relationship between the properties and the particle size of the Tb0.3Dy0.7Fe1.9 powder: the increases in the particle-size distribution of the Tb0.3Dy0.7Fe1.9 powder in the matrix amplify the magnetostrictive responses and the compressive modulus values. Moreover, it was found that the key role in efficiency of the transformation of magnetic energy into mechanical plays the initial compressing pre-stress.

  7. Research on lunar materials. [optical, chemical, and electrical properties

    Science.gov (United States)

    Gold, T.

    1978-01-01

    Abstracts of 14 research reports relating to investigations of lunar samples are presented. The principal topics covered include: (1) optical properties of surface and core samples; (2) chemical composition of the surface layers of lunar grains: Auger electron spectroscopy of lunar soil and ground rock samples; (3) high frequency electrical properties of lunar soil and rock samples and their relevance for the interpretation of lunar radar observations; (4) the electrostatic dust transport process; (5) secondary electron emission characteristics of lunar soil samples and their relevance to the dust transportation process; (6) grain size distribution in surface soil and core samples; and (7) the optical and chemical effects of simulated solar wind (2keV proton and a particle radiation) on lunar material.

  8. Development and mechanical properties of structural materials from lunar simulants

    Science.gov (United States)

    Desai, Chandra S.; Girdner, K.; Saadatmanesh, H.; Allen, T.

    1991-01-01

    Development of the technologies for manufacture of structural and construction materials on the Moon, utilizing local lunar soil (regolith), without the use of water, is an important element for habitats and explorations in space. Here, it is vital that the mechanical behavior such as strength and flexural properties, fracture toughness, ductility and deformation characteristics be defined toward establishment of the ranges of engineering applications of the materials developed. The objective is to describe the research results in two areas for the above goal: (1) liquefaction of lunar simulant (at about 100 C) with different additives (fibers, powders, etc.); and (2) development and use of a new triaxial test device in which lunar simulants are first compressed under cycles of loading, and then tested with different vacuums and initial confining or in situ stress.

  9. Dosimetric properties of natural quartz grains extracted from fired materials

    DEFF Research Database (Denmark)

    Bluszcz, A.; Bøtter-Jensen, L.

    1995-01-01

    The paper describes an examination of the dosimetric properties of natural quartz grains extracted from ancient fired materials. Eleven samples of different origin were tested for their TL and GLSL (green light stimulated luminescence) sensitivities within the mGy dose range. Very promising results...... were obtained showing the possibility of measuring the doses of around 10 mGy with 1% precision using GLSL or TL and using the single aliquot technique for natural quartz as a dosimeter. The lowest detectable dose was estimated to be lower than 500 mu Gy. The results obtained indicate that natural...... quartz grains from selected materials could be used for the dosimetry of environmental gamma radiation for the purposes of paleodosimetric dating methods as well as for accident dosimetry....

  10. Pulsed power experiments in hydrodynamics and material properties

    CERN Document Server

    Reinovsky, R E

    1999-01-01

    A new application for high performance pulsed power program, the production of high energy density environments in materials for the study of material properties and hydrodynamics in complex geometries, has joined family of radiation source applications in the Stockpile Stewardship. The principle tool for producing high energy density environments is the high precision, magnetically imploded, near-solid density liner. The most attractive pulsed power system for driving such experiments is an ultra-high current, low impedance, microsecond time scale source that is economical both to build and operate. The 25-MJ Atlas capacitor bank system currently under construction at Los Alamos is the first system of its scale specifically designed to drive high precision solid liners. Delivering 30 MA, Atlas will provide liner velocities 12-15 km/sec and kinetic energies of 1-2 MJ /cm with extensive diagnostics and excellent reproducibility. Explosive flux compressor technology provides access to currents exceeding 100 MA ...

  11. Structure and Property Characterization of Oyster Shell Cementing Material

    Institute of Scientific and Technical Information of China (English)

    钟彬杨; 周强; 单昌锋; 于岩

    2012-01-01

    Oyster shell powder was used as the admixture of ordinary portland cement.The effects of different addition amounts and grinding ways on the strength and stability of cement mortar were discussed and proper addition amount of oyster shell powder was determined.The structure and property changes of cementing samples with different oyster shell powder contents were tested by XRD and SEM means.The results revealed that compressive and rupture strengths of the sample with 10% oyster shell powder was close to those of the original one without addition.Stability experiment showed that the sample prepared by pat method had smooth surface without crack and significant expansion or shrinkage after pre-curing and boiling,which indicated that cementing material dosed with oyster shell powder had fine stability.XRD and SEM observation showed that oyster shell independently exists in the cementing material.

  12. Comparison of Electrical Properties between Fluoroapatite and Hydroxyapatite Materials

    Science.gov (United States)

    Laghzizil, A.; El Herch, N.; Bouhaouss, A.; Lorente, G.; Macquete, J.

    2001-01-01

    By appropriate modifications of existing precipitation methods, apatite samples of formula M10(PO4)6X2 (M=Ca, Pb, Ba and X=F, OH) were prepared at 80°C. Samples were characterized using X-ray diffraction, infrared, 31P NMR, SEM, and chemical analysis. By comparing the effect of fluoride and hydroxide ions on ionic conductivity measurements, it was concluded that the fluorinated materials (MFAp) were better conductors than other hydroxyapatites (MHAp). The F- and H+ ions are the main charge carriers, respectively, in fluoroapatite and in hydroxyapatite compounds. The most pronounced effect on the conduction properties was observed in the lead apatite material. These results should provide important physico-chemical information for ionic diffusion of the roles played by fluoride in inhibiting dental caries.

  13. Properties and processing of nanocrystalline materials. Quarterly report

    Energy Technology Data Exchange (ETDEWEB)

    Valiev, R.Z.

    1996-01-22

    The present Report completes the investigations in the frame of the project for the first year. It is important to estimate our achievements in the investigation of properties of nanocrystalline materials obtained by severe plastic deformation and their production. We think that the main results obtained can be summarized as follows: (1) We performed an improvement of the die-set for equal channel (ECA) pressing and torsion under high pressure with the aim to increase dimensions of the samples produced and to conduct processing of low ductile materials. (2) It was established that in pure metals severe plastic deformation led to the formation of an ultra fine-grained structure with a mean grain size of 100-200 nm, while in alloys due to severe plastic deformation and/or special methods of treatment (a decrease in the temperature of deformation, an increase of the pressure applied etc.) the grain size could be decreased down to a few tens of manometers.

  14. Relaxor behavior and electrical properties of high dielectric constant materials

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Several typical high dielectric constant materials are reviewed to study the electrical properties and relaxation mechanism. It is found that a Lorenz-type law can be used to describe the dielectric permit- tivity of either the normal ferroelectrics with or without diffuse phase transitions (DPT) or the typical ferroelectric relaxors. The ferroelectric DPT can be well described by just one fitting process using the Lorenz-type law, while the relaxor ferroelectric transition needs two independent fitting processes. The Lorenz-type law fails at the low temperature side of the dielectric maximum of a first-order ferroelectric phase transition. Above the transition temperature, the dielectric curves of all the studied materials can be well described by a Lorenz-type law.

  15. Relaxor behavior and electrical properties of high dielectric constant materials

    Institute of Scientific and Technical Information of China (English)

    FAN HuiQing; KE ShanMing

    2009-01-01

    Several typical high dielectric constant materials are reviewed to study the electrical properties and relaxation mechanism.It is found that a Lorenz-type law can be used to describe the dielectric permitUvity of either the normal ferroelectrics with or without diffuse phase transitions(DPT)or the typical ferroelectric relaxors.The ferroelectric DPT can be well described by just one fitting process using the Lorenz-type law,while the relaxor ferroelectric transition needs two independent fitting processes.The Lorenz-type law fails at the low temperature side of the dielectric maximum of a first-order ferroelectric phase transition.Above the transition temperature,the dielectric curves of all the studied materials can be well described by a Lorenz-type law.

  16. Electronic, Vibrational and Thermoelectric Properties of Two-Dimensional Materials

    Science.gov (United States)

    Wickramaratne, Darshana

    The discovery of graphene's unique electronic and thermal properties has motivated the search for new two-dimensional materials. Examples of these materials include the layered two-dimensional transition metal dichalcogenides (TMDC) and metal mono-chalcogenides. The properties of the TMDCs (eg. MoS 2, WS2, TaS2, TaSe2) and the metal mono-chalcogenides (eg. GaSe, InSe, SnS) are diverse - ranging from semiconducting, semi-metallic and metallic. Many of these materials exhibit strongly correlated phenomena and exotic collective states such as exciton condensates, charge density waves, Lifshitz transitions and superconductivity. These properties change as the film thickness is reduced down to a few monolayers. We use first-principles simulations to discuss changes in the electronic and the vibrational properties of these materials as the film thickness evolves from a single atomic monolayer to the bulk limit. In the semiconducting TMDCs (MoS2, MoSe2, WS2 and WSe2) and monochalcogenides (GaS, GaSe, InS and InSe) we show confining these materials to their monolayer limit introduces large band degeneracies or non-parabolic features in the electronic structure. These changes in the electronic structure results in increases in the density of states and the number of conducting modes. Our first-principles simulations combined with a Landauer approach show these changes can lead to large enhancements up to an order of magnitude in the thermoelectric performance of these materials when compared to their bulk structure. Few monolayers of the TMDCs can be misoriented with respect to each other due to the weak van-der-Waals (vdW) force at the interface of two monolayers. Misorientation of the bilayer semiconducting TMDCs increases the interlayer van-der-Waals gap distance, reduces the interlayer coupling and leads to an increase in the magnitude of the indirect bandgap by up to 100 meV compared to the registered bilayer. In the semi-metallic and metallic TMDC compounds (TiSe2, Ta

  17. Optimization of the magnetic properties of materials for fluxgate sensors

    Directory of Open Access Journals (Sweden)

    Luiz Carlos de Carvalho Benyosef

    2008-06-01

    Full Text Available A study was made of the variation of the magnetic properties of cobalt-based alloys using different compositions of CoFeSiB and CoFeSiBCr systems, which were produced by the melt-spinning technique and some of them subjected to a stress annealing treatment. A comparative study of core geometry and supporting material was also performed in order to obtain low noise fluxgate sensor core using amorphous magnetic ribbons of these alloys. The best alloy was a stress annealed Co67.5Fe3.5Si17.4B11.6 sample, which yielded fluxgate sensors with lower noise levels than those of commercial crystalline materials.

  18. Modelling of composite propellant properties

    NARCIS (Netherlands)

    Keizers, H.L.J.; Hordijk, A.C.; Vliet, L.D. van; Bouquet, F.

    2000-01-01

    State-of-the-art composite propellants are based on solid particles (AP, Aluminium) in a polymeric HTPB based binder system. The usability of a propellant for a particular application is dependent on a large number of properties. These different properties sometimes result in contradictory requireme

  19. Fabrication of nanoscale to macroscale nickel-multiwall carbon nanotube hybrid materials with tunable material properties

    Science.gov (United States)

    Abdalla, Ahmed M.; Majdi, Tahereh; Ghosh, Suvojit; Puri, Ishwar K.

    2016-12-01

    To utilize their superior properties, multiwall carbon nanotubes (MWNTs) must be manipulated and aligned end-to-end. We describe a nondestructive method to magnetize MWNTs and provide a means to remotely manipulate them through the electroless deposition of magnetic nickel nanoparticles on their surfaces. The noncovalent bonds between Ni nanoparticles and MWNTs produce a Ni-MWNT hybrid material (NiCH) that is electrically conductive and has an enhanced magnetic susceptibility and elastic modulus. Our experiments show that MWNTs can be plated with Ni for Ni:MWNT weight ratios of γ = 1, 7, 14 and 30, to control the material properties. The phase, atom-level, and morphological information from x-ray diffraction, energy dispersive x-ray spectroscopy, scanning electron microscopy, transmission electron microscopy, dark field STEM, and atomic force microscopy clarify the plating process and reveal the mechanical properties of the synthesized material. Ni metalizes at the surface of the Pd catalyst, forming a continuous wavy layer that encapsulates the MWNT surfaces. Subsequently, Ni acts as an autocatalyst, allowing the plating to continue even after the original Pd catalyst has been completely covered. Raising γ increases the coating layer thickness from 10 to 150 nm, which influences the NiCH magnetic properties and tunes its elastic modulus from 12.5 to 58.7 GPa. The NiCH was used to fabricate Ni-MWNT macrostructures and tune their morphologies by changing the direction of an applied magnetic field. Leveraging the hydrophilic Ni-MWNT outer surface, a water-based conductive ink was created and used to print a conductive path that had an electrical resistivity of 5.9 Ω m, illustrating the potential of this material for printing electronic circuits.

  20. Hygrothermal Simulation of Foundations: Part 1 - Soil Material Properties

    Energy Technology Data Exchange (ETDEWEB)

    Kehrer, Manfred [ORNL; Pallin, Simon B [ORNL

    2012-10-01

    The hygrothermal performance of soils coupled to buildings is a complicated process. A computational approach for heat transfer through the ground has been well defined (EN ISO 13370:2007, 2007), and simplified methods have been developed (Staszczuk, Radon, and Holm 2010). However, these approaches generally ignore the transfer of soil moisture, which is not negligible (Janssen, Carmeliet, and Hens 2004). This study is divided into several parts. The intention of the first part is to gather, comprehend and adapt soil properties from Soil Science. The obtained information must be applicable to related tasks in Building Science and validated with hygrothermal calculation tools. Future parts of this study will focus on the validation aspect of the soil properties to be implemented. Basic changes in the software code may be requested at this time. Different types of basement construction will be created with a hygrothermal calculation tool, WUFI. Simulations from WUFI will be compared with existing or ongoing measurements. The intentions of the first part of this study have been fulfilled. The soil properties of interest in Building Science have been defined for 12 different soil textures. These properties will serve as input parameters when performing hygrothermal calculations of building constructions coupled to soil materials. The reliability of the soil parameters will be further evaluated with measurements in Part 2.

  1. Anticoagulation property and security of artificial heart valve material

    Institute of Scientific and Technical Information of China (English)

    WANG Xianghui; XU Jingfang; LIU Xianghuai; ZHANG Feng; LI Changrong; YU Liujiang; ZHENG Zhihong; WANG Xi; JIANG Zhenbin; CHEN Anqing

    2005-01-01

    Heart valve diseases threaten human health. One reliable way to save lives of such patients is to replace the pathologically changed heart valves by artificial ones. Over 2 million patients have received LTI-carbon heart valve's implantation. However, the thrombosis after the implantation is one of the difficulties that need to be solved. In order to improve the blood compatibility and security of mechanical heart valves, ion beam technology was used to modify the surface properties of the materials. The investigation results have been summarized in this paper.

  2. Mechanical Properties of Heat Exchanger Tube Materials at Elevated Temperatures

    Science.gov (United States)

    Kahl, Sören; Zajac, Jozefa; Ekström, Hans-Erik

    Since automotive heat exchangers are operated at elevated temperatures and under varying pressures, both static and dynamic mechanical properties should be known at the relevant temperatures. We have collected elevated-temperature tensile test data, elevated-temperature stress amplitude-fatigue life data, and creep-rupture data in a systematic fashion over the past years. For thin, soft, and braze-simulated heat exchanger tube materials tested inside closed furnaces, none of the well-established methods for crack detection and observation can be applied. In our contribution, we present a simple statistical method to estimate the time required for crack initiation.

  3. Preparation and properties of antimony thin film anode materials

    Institute of Scientific and Technical Information of China (English)

    SU Shufa; CAO Gaoshao; ZHAO Xinbing

    2004-01-01

    Metallic antimony thin films were deposited by magnetron sputtering and electrodeposition. Electrochemical properties of the thin film as anode materials for lithium-ion batteries were investigated and compared with those of antimony powder. It was found that both magnetron sputtering and electrodeposition are easily controllable processes to deposit antimony films with fiat charge/discharge potential plateaus. The electrochemical performances of antimony thin films, especially those prepared with magnetron sputtering, are better than those of antimony powder. The reversible capacities of the magnetron sputtered antimony thin film are above 400 mA h g-1 in the first 15 cycles.

  4. Electromagnetic properties in ferroelectric materials; Proprietes electromagnetiques des materiaux ferroelectriques

    Energy Technology Data Exchange (ETDEWEB)

    Ravez, J.; Elissalde, C. [Institut de Chimie de la Matiere Condensee, 33 - Pessac (France); Miane, J.L. [ENSCPB, 33 - Talence (France)

    1996-12-31

    The recent development of network analyzers has allowed electromagnetic property studies in perovskite-type ferroelectric materials in a large frequency range ({approx} 10{sup 2}-10{sup 10} Hz). A high frequency ({approx} 10{sup 7}-10{sup 10} Hz) relaxation has been evidenced. The origin of the relaxation process has been determined: it is an intrinsic mechanism directly related to the crystal lattice. In the light of the obtained results, physical-chemistry laws can be used to modulate the relaxation frequency using appropriate ionic substitutions. (authors). 13 refs., 6 figs., 1 tab.

  5. Electrical properties of spherical dipole antennas with lossy material cores

    DEFF Research Database (Denmark)

    Hansen, Troels Vejle; Kim, Oleksiy S.; Breinbjerg, Olav

    2012-01-01

    A spherical magnetic dipole antenna with a linear, isotropic, homogenous, passive, and lossy material core is modeled analytically, and closed form expressions are given for the internally stored magnetic and electric energies, the radiation efficiency, and radiation quality factor. This model...... size and permittivity, focusing on the effects of magnetic core losses for a simple magnetic dispersion model, to illustrate how stored energies, efficiency and quality factor are affected. This shows that large magnetic losses can be beneficial, as these can produce a relatively high efficiency....

  6. Mechanical properties of new dental pulp-capping materials.

    Science.gov (United States)

    Nielsen, Matthew J; Casey, Jeffery A; VanderWeele, Richard A; Vandewalle, Kraig S

    2016-01-01

    The mechanical properties of pulp-capping materials may affect their resistance to fracture during placement of a final restorative material or while supporting an overlying restoration over time. The purpose of this study was to compare the compressive strength, flexural strength, and flexural modulus of 2 new pulp-capping materials (TheraCal LC and Biodentine), mineral trioxide aggregate (MTA), and calcium hydroxide over time. Specimens were created in molds and tested to failure in a universal testing machine after 15 minutes, 3 hours, and 24 hours. The MTA specimens did not set at 15 minutes. At all time periods, TheraCal LC had the greatest compressive and flexural strengths. After 3 and 24 hours, Biodentine had the greatest flexural modulus. TheraCal LC had greater early strength to potentially resist fracture during immediate placement of a final restorative material. Biodentine had greater stiffness after 3 hours to potentially provide better support of an overlying restoration under function over time.

  7. Mechanical properties of gangue-containing aluminosilicate based cementitious materials

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    High performance aluminosilicate based cementitious materials were produced using calcined gangue as one of the major raw materials.The gangue was calcined at 500℃.The main constituent was calcined gangue, fly ash and slag, while alkali-silicate solutions were used as the diagenetic agent.The structure of gangue-containing aluminosilicate based cementitious materials was studied by the methods of IR, NMR and SEM.The results show that the mechanical properties are affected by the mass ratio between the gangue, slag and fly ash, the kind of activator and additional salt.For 28-day curing time, the compressive strength of the sample with a mass proportion of 2:1:1 (gangue: slag: fly ash) is 58.9 MPa, while the compressive strength of the sample containing 80wt%gangue can still be up to 52.3 MPa.The larger K+ favors the formation of large silicate oligomers with which Al(OH)4- prefers to bind.Therefore, in Na-K compounding activator solutions more oligomers exist which result in a stronger compressive strength of aluminosilicate-based cementitious materials than in the case of Na-containing activator.The reasons for this were found through IR and NMR analysis.Glauber's salt reduces the 3-day compressive strength of the paste, but increases its 7-day and 28-day compressive strengths.

  8. Mechanisms Responsible for Microwave Properties in High Performance Dielectric Materials

    Science.gov (United States)

    Zhang, Shengke

    Microwave properties of low-loss commercial dielectric materials are optimized by adding transition-metal dopants or alloying agents (i.e. Ni, Co, Mn) to tune the temperature coefficient of resonant frequency (tau f) to zero. This occurs as a result of the temperature dependence of dielectric constant offsetting the thermal expansion. At cryogenic temperatures, the microwave loss in these dielectric materials is dominated by electron paramagnetic resonance (EPR) loss, which results from the spin-excitations of d-shell electron spins in exchange-coupled clusters. We show that the origin of the observed magnetically-induced shifts in the dielectric resonator frequency originates from the same mechanism, as described by the Kramers-Kronig relations. The temperature coefficient of resonator frequency, tauf, is related to three material parameters according to the equation, tau f = - (½ tauepsilon + ½ taumu + alphaL), where tauepsilon, taumu , and alphaL are the temperature coefficient of dielectric constant, magnetic permeability, and lattice constant, respectively. Each of these parameters for dielectric materials of interest are measured experimentally. These results, in combination with density functional simulations, developed a much improved understanding of the fundamental mechanisms responsible for tau f. The same experimental methods have been used to characterize in-situ the physical nature and concentration of performance-degrading point defects in the dielectrics of superconducting planar microwave resonators.

  9. Strain Rate Dependant Material Model for Orthotropic Metals

    Science.gov (United States)

    Vignjevic, Rade

    2016-08-01

    In manufacturing processes anisotropic metals are often exposed to the loading with high strain rates in the range from 102 s-1 to 106 s-1 (e.g. stamping, cold spraying and explosive forming). These types of loading often involve generation and propagation of shock waves within the material. The material behaviour under such a complex loading needs to be accurately modelled, in order to optimise the manufacturing process and achieve appropriate properties of the manufactured component. The presented research is related to development and validation of a thermodynamically consistent physically based constitutive model for metals under high rate loading. The model is capable of modelling damage, failure and formation and propagation of shock waves in anisotropic metals. The model has two main parts: the strength part which defines the material response to shear deformation and an equation of state (EOS) which defines the material response to isotropic volumetric deformation [1]. The constitutive model was implemented into the transient nonlinear finite element code DYNA3D [2] and our in house SPH code. Limited model validation was performed by simulating a number of high velocity material characterisation and validation impact tests. The new damage model was developed in the framework of configurational continuum mechanics and irreversible thermodynamics with internal state variables. The use of the multiplicative decomposition of deformation gradient makes the model applicable to arbitrary plastic and damage deformations. To account for the physical mechanisms of failure, the concept of thermally activated damage initially proposed by Tuller and Bucher [3], Klepaczko [4] was adopted as the basis for the new damage evolution model. This makes the proposed damage/failure model compatible with the Mechanical Threshold Strength (MTS) model Follansbee and Kocks [5], 1988; Chen and Gray [6] which was used to control evolution of flow stress during plastic deformation. In

  10. Determination Of Thermal And Mechanical Properties Of Packaging Materials For The Use In FEM-Simulations

    Science.gov (United States)

    Roellig, Mike; Boehme, Bjoern; Meier, Karsten; Metasch, René

    2011-09-01

    Conventional and future electronic packages merge several different materials. Polymers, metals, solders, dielectrics, glasses, silicon, composites come together and show strong mechanical and material interaction. These interfacial effects increase if the miniaturization and diversification keep on rising as it is proposed. Many efforts have to be done to assure the system reliability of new electronic packages. The Finite Element Simulation has the ability to support the development process of new packages. The application of the FEM-analysis requires the knowledge about the precise mechanical and thermal behaviour of the materials. The paper presents different measurement methods to determine accurate mechanical material properties of moulding compound polymers, underfillers, solder mask, and wafer photo resist and solder joints. The temperature dependency is essential to be respected. The polymer materials moulding compound as well as solder mask were characterized by Dynamic Mechanical Analysis under humidity influences to determine mechanical properties as function of moisture and temperature. Further experiments on polymer were conducted to extract the cure kinetics by Differential Scanning Calorimetry and to determine Bulk Modulus by Pressure-Volume-Temperature experiments (PVT). Altogether, these material properties need to be modeled in a comprehensive way fitting to each other. The common practice of just compiling data from different sources has been found to fail yielding in reliable and accurate results. The conditions under which the data were determined may cause mismatches between them and cause inconsistencies within the model. If a convergent solution was obtained at all, much simulation time would be needed as many iterations with small time steps were needed. In order to avoid this, the paper reports an approach of characterizing the temperature and time dependent mechanical material properties in one comprehensive scheme. The solder

  11. Experimental Study on the Comparison of the Material Properties of Glass Wool Used as Building Materials

    Directory of Open Access Journals (Sweden)

    Kyoung-Woo KIM

    2014-04-01

    Full Text Available Artificial mineral fibers such as glass wool or stone wool are commonly used in building walls, ceilings and floors as a major insulation material for buildings. Among the material properties of building materials, thermal conductivity, the sound absorption coefficient, compressibility, and dynamic stiffness are regarded as important performance requirements since they directly affect the thermal and acoustic properties of the building. This study measured the changes of the thermal and acoustical performances of glass wool that was actually installed for a long time to the outer wall of a building as an insulation material through a comparison with recently produced glass wool. The results showed that the measured thermal conductivities of the old and the new specimens both rise with an increase of temperature, showing quite similar results in both specimens over temperature ranges of (0 – 20 ºC. The noise reduction coefficient decreased by 0.1 in the old specimen and the difference of the compressibilities in both specimens was shown to be 7.32 mm. The dynamic stiffness of the old specimen was found to be 1.28 MN/m3 higher than that of the new specimen.DOI: http://dx.doi.org/10.5755/j01.ms.20.1.3714

  12. Effect of intercostal muscle and costovertebral joint material properties on human ribcage stiffness and kinematics.

    Science.gov (United States)

    Kindig, Matthew; Li, Zuoping; Kent, Richard; Subit, Damien

    2015-01-01

    Current finite element (FE) models of the human thorax are limited by the lack of local-level validation, especially in the ribcage. This study exercised an existing FE ribcage model for a 50th percentile male under quasi-static point loading and dynamic sternal loading. Both force-displacement and kinematic responses of the ribcage were compared against experimental data. The sensitivity of the model response to changes in the material properties of the costovertebral (CV) joints and intercostal muscles was assessed. The simulations found that adjustments to the CV joints tended to change the amount of rib rotation in the sagittal plane, while changes to the elastic modulus and thickness of the intercostal muscles tended to alter both the stiffness and the direction and magnitude of rib motions. This study can lend insight into the role that the material properties of these two thoracic structures play in the dynamics of the ribcage during a frontal loading condition.

  13. CRACK PROPAGATING IN FUNCTIONALLY GRADED COATING WITH ARBITRARILY DISTRIBUTED MATERIAL PROPERTIES BONDED TO HOMOGENEOUS SUBSTRATE

    Institute of Scientific and Technical Information of China (English)

    Zhanqi Cheng; Danying Gao; Zheng Zhong

    2010-01-01

    In this paper,a finite crack with constant length(Yoffe type crack)propagating in a functionally graded coating with spatially varying elastic properties bonded to a homoge-neous substrate of finite thickness under anti-plane loading was studied.A multi-layered model is employed to model arbitrary variations of material properties based on two linearly-distributed material compliance parameters.The mixed boundary problem is reduced to a system of singular integral equations that are solved numerically.Some numerical examples are given to demonstrate the accuracy,efficiency and versatility of the model.The numerical results show that the graded parameters,the thicknesses of the interracial layer and the two homogeneous layers,the crack size and speed have significant effects on the dynamic fracture behavior.

  14. Approximation of mechanical properties of sintered materials with discrete element method

    Science.gov (United States)

    Dosta, Maksym; Besler, Robert; Ziehdorn, Christian; Janßen, Rolf; Heinrich, Stefan

    2017-06-01

    Sintering process is a key step in ceramic processing, which has strong influence on quality of final product. The final shape, microstructure and mechanical properties, e.g. density, heat conductivity, strength and hardness are depending on the sintering process. In order to characterize mechanical properties of sintered materials, in this contribution we present a microscale modelling approach. This approach consists of three different stages: simulation of the sintering process, transition to final structure and modelling of mechanical behaviour of sintered material with discrete element method (DEM). To validate the proposed simulation approach and to investigate products with varied internal structures alumina powder has been experimentally sintered at different temperatures. The comparison has shown that simulation results are in a very good agreement with experimental data and that the novel strategy can be effectively used for modelling of sintering process.

  15. Energy based model for temperature dependent behavior of ferromagnetic materials

    Science.gov (United States)

    Sah, Sanjay; Atulasimha, Jayasimha

    2017-03-01

    An energy based model for temperature dependent anhysteretic magnetization curves of ferromagnetic materials is proposed and benchmarked against experimental data. This is based on the calculation of macroscopic magnetic properties by performing an energy weighted average over all possible orientations of the magnetization vector. Most prior approaches that employ this method are unable to independently account for the effect of both inhomogeneity and temperature in performing the averaging necessary to model experimental data. Here we propose a way to account for both effects simultaneously and benchmark the model against experimental data from 5 K to 300 K for two different materials in both annealed (fewer inhomogeneities) and deformed (more inhomogeneities) samples. This demonstrates that this framework is well suited to simulate temperature dependent experimental magnetic behavior.

  16. Material properties of individual menisci and their attachments obtained through inverse FE-analysis.

    Science.gov (United States)

    Freutel, Maren; Galbusera, Fabio; Ignatius, Anita; Dürselen, Lutz

    2015-06-01

    Meniscal properties for computational methods have already been proposed. However, it is well known that there is high intra subject variability in the material properties of soft tissues and that disruption of the fiber network alters the biomechanics of the meniscus. Therefore, the objective of this study was to establish a non invasive method to determine the material properties of the individual menisci and their attachments using inverse FE-analyses. In a previous study, the 3D displacements of the meniscus and its attachments under axial joint loads were determined for intact porcine knees. To simulate the experimental response in individual FE-analyses (n=5), an anisotropic, hyperelastic meniscus matrix was embedded in a poroelastic model. During a particle swarm optimization, the difference between the force applied to the meniscus during the experiment and the femoral surface reaction force of the FE model at equilibrium was minimized by varying four material parameters. Afterwards, a prediction error was determined to describe how well the material parameter fit to each of the three displacement directions. Additionally, the stresses occurring in the meniscus were evaluated. The error of the material parameter optimization was on average 6.5±4.4%. The best fitting material parameter combination revealed an error of 1.2%. The highest stresses occurred in the region between the pars intermedia and posterior horn of the meniscus. The individual material properties of the meniscus were successfully obtained with a combination of previously reported, noninvasively measured 3D displacements and inverse FE-analyses. The methodology presented in this study is a promising contribution to the detection of degeneration within the meniscus. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Mathematical model predicts the elastic behavior of composite materials

    Directory of Open Access Journals (Sweden)

    Zoroastro de Miranda Boari

    2005-03-01

    Full Text Available Several studies have found that the non-uniform distribution of reinforcing elements in a composite material can markedly influence its characteristics of elastic and plastic deformation and that a composite's overall response is influenced by the physical and geometrical properties of its reinforcing phases. The finite element method, Eshelby's method and dislocation mechanisms are usually employed in formulating a composite's constitutive response. This paper discusses a composite material containing SiC particles in an aluminum matrix. The purpose of this study was to find the correlation between a composite material's particle distribution and its resistance, and to come up with a mathematical model to predict the material's elastic behavior. The proposed formulation was applied to establish the thermal stress field in the aluminum-SiC composite resulting from its fabrication process, whereby the mixture is prepared at 600 °C and the composite material is used at room temperature. The analytical results, which are presented as stress probabilities, were obtained from the mathematical model proposed herein. These results were compared with the numerical ones obtained by the FEM method. A comparison of the results of the two methods, analytical and numerical, reveals very similar average thermal stress values. It is also shown that Maxwell-Boltzmann's distribution law can be applied to identify the correlation between the material's particle distribution and its resistance, using Eshelby's thermal stresses.

  18. Finite element simulations on the mechanical properties of MHS materials

    Institute of Scientific and Technical Information of China (English)

    Z.Y.Gao; T.X.Yu; D.Karagiozova

    2007-01-01

    Finite element simulations are carried out toexamine the mechanical behavior of the metallic hollowsphere (MHS) material during their large plastic defor-mation and to estimate the energy absorbing capac-ity of these materials under uniaxial compression.Asimplified model is proposed from experimental obser-vations to describe the connection between theneighboring spheres,which greatly improves the com-putation efficiency.The effects of the governing physi-cal and geometrical parameters are evaluated; whilst aspecial attention is paid to the plateau stress,which isdirectly related to the energy absorbing capacity.Finally,the empirical functions of the relative material densityare proposed for the elastic modulus,yield strength andplateau stress for FCC packing arrangement of hollowspheres,showing a good agreement with the experimen-tal results obtained in our previous study.

  19. Material properties of Grade 91 steel at elevated temperature and their comparison with a design code

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hyeong Yeon; Kim, Woo Gon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Han Sang; Kim, Yun Jae [Korea Univ., Seoul (Korea, Republic of)

    2013-10-15

    In this study, the material properties of tensile strength, creep properties, and creep crack growth model for Gr.91 steel at elevated temperature were obtained from material tests at KAERI, and the test data were compared with those of the French elevated temperature design code, RCC-MRx. The conservatism of the material properties in the French design code is highlighted. Mod.9Cr-1Mo (ASME Grade 91; Gr.91) steel is widely adopted as candidate material for Generation IV nuclear systems as well as for advanced thermal plants. In a Gen IV sodium-cooled fast reactor of the PGSFR (Prototype Gen IV Sodium-cooled Fast Reactor) being developed by KAERI (Korea Atomic Energy Research Institute), Gr.91 steel is selected as the material for the steam generator, secondary piping, and decay heat exchangers. However, as this material has a relatively shorter history of usage in an actual plant than austenitic stainless steel, there are still many issues to be addressed including the long-term creep rupture life extrapolation and ratcheting behavior with cyclic softening characteristics.

  20. Dynamic modelling of packaging material flow systems.

    Science.gov (United States)

    Tsiliyannis, Christos A

    2005-04-01

    A dynamic model has been developed for reused and recycled packaging material flows. It allows a rigorous description of the flows and stocks during the transition to new targets imposed by legislation, product demand variations or even by variations in consumer discard behaviour. Given the annual reuse and recycle frequency and packaging lifetime, the model determines all packaging flows (e.g., consumption and reuse) and variables through which environmental policy is formulated, such as recycling, waste and reuse rates and it identifies the minimum number of variables to be surveyed for complete packaging flow monitoring. Simulation of the transition to the new flow conditions is given for flows of packaging materials in Greece, based on 1995--1998 field inventory and statistical data.