Computational fluid dynamic (CFD) analysis on ALUDRA SR-10 UAV with parachute recovery system

Science.gov (United States)

Saim, R.; Mohd, S.; Shamsudin, S. S.; Zulkifli, M. F.; Omar, Z.; Subari@Rahmat, Z.; Masrom, M. F. Mohd; Zaki, Y.

2017-09-01

In an operation, belly landing is mostly applied as recovery method especially on research Unmanned Aerial Vehicle (UAV) such as Aludra SR-10. This type of landing method may encounter tough landing on hard soil and gravel which create high impact load on the aircraft. The impact may cause structural or system damage which costly to be repaired. Nowadays, Parachute Recovery System (PRS) recently used in numerous different tasks such as landing purpose to replace belly landing technique. Parachute use in this system to slow down flying or falling UAV to a safe landing by opening the canopy to increase aerodynamic drag. This paper was described the Computational Fluid Dynamic (CFD) analysis on ALUDRA SR-10 model with two different conditions i.e. the UAV equipped with and without parachute in order to identify the changes of aerodynamic characteristics. This simulation studies using solid models of aircraft and hemisphere parachute and was carried out by using ANSYS 16.0 Fluent under steady and turbulent flow and was modelled using the k-epsilon (k-ε) turbulence model. This simulation was limited to determine the drag force and drag coefficient. The obtained result showed that implementation of parachute increase 0.25 drag coefficient of the aircraft that is from 0.93 to 1.18. Subsequent to the reduction of descent rate caused by the parachute, the drag force of the aircraft increase by 0.76N. These increasing of drag force of the aircraft will produce lower terminal velocity which is expected to reduce the impact force on the aircraft during landing.

FEAR AND ENTHUSIASM IN SPORT PARACHUTING,

Science.gov (United States)

Replies to a mail questionnaire by 825 sport parachutists affiliated with 103 parachute clubs are the data of this study. Questionnaires were...parachutists, attitudes relevant to sport parachuting, and included the Ma and Hy scales from the MMP1, a Draw-A-Person Test, and four story stimulus pictures

Verification and Validation of the Spring Model Parachute Air Delivery System in Subsonic Flow

Science.gov (United States)

2015-02-27

permeability [5]. Thus the coupling of the vertical flow with the permeable and flexible fabric may have significant difference with rigid bluff bodies...Vorticity, from left to right: γ = 0, 0.25, 0.5, 0.75 of the canopies and risers . Among these parachutes, the T-10 parachute is used by the Army as a...G. F. Homicz, and A. A. Gossler, Fluid- structure coupling for lightweight flexible bodies, 17th AIAA Aerodynamic Decelerator Systems Technology

Pilot ejection, parachute, and helicopter crash injuries.

Science.gov (United States)

McBratney, Colleen M; Rush, Stephen; Kharod, Chetan U

2014-01-01

USAF Pararescuemen (PJs) respond to downed aircrew as a fundamental mission for personnel recovery (PR), one of the Air Force's core functions. In addition to responding to these in Military settings, the PJs from the 212 Rescue Squadron routinely respond to small plane crashes in remote regions of Alaska. While there is a paucity of information on the latter, there have been articles detailing injuries sustained from helicopter crashes and while ejecting or parachuting from fixed wing aircraft. The following represents a new chapter added to the Pararescue Medical Operations Handbook, Sixth Edition (2014, editors Matt Wolf, MD, and Stephen Rush, MD, in press). It was designed to be a quick reference for PJs and their Special Operations flight surgeons to help with understanding of mechanism of injury with regard to pilot ejection, parachute, and helicopter accident injuries. It outlines the nature of the injuries sustained in such mishaps and provides an epidemiologic framework from which to approach the problem. 2014.

75 FR 47236 - Golden Parachute and Indemnification Payments

Science.gov (United States)

2010-08-05

... golden parachute, severance, indemnification or other agreement. Claims for employee welfare benefits or... legitimate employee severance payments and improper golden parachute payments. DATES: Comments must be... FICUs with greater clarity on the distinction between legitimate employee severance payments and...

Reconstruction of Orion Engineering Development Unit (EDU) Parachute Inflation Loads

Science.gov (United States)

Ray, Eric S.

2013-01-01

The process of reconstructing inflation loads of Capsule Parachute Assembly System (CPAS) has been updated as the program transitioned to testing Engineering Development Unit (EDU) hardware. The equations used to reduce the test data have been re-derived based on the same physical assumptions made by simulations. Due to instrumentation challenges, individual parachute loads are determined from complementary accelerometer and load cell measurements. Cluster inflations are now simulated by modeling each parachute individually to better represent different inflation times and non-synchronous disreefing. The reconstruction procedure is tailored to either infinite mass or finite mass events based on measurable characteristics from the test data. Inflation parameters are determined from an automated optimization routine to reduce subjectivity. Infinite mass inflation parameters have been re-defined to avoid unrealistic interactions in Monte Carlo simulations. Sample cases demonstrate how best-fit inflation parameters are used to generate simulated drag areas and loads which favorably agree with test data.

Wind tunnel tests of modified cross, hemisflo, and disk-gap-band parachutes with emphasis in the transonic range

Science.gov (United States)

Foughner, J. T., Jr.; Alexander, W. C.

1974-01-01

Transonic wind-tunnel studies were conducted with modified cross, hemisflo, and disk-gap-band parachute models in the wake of a cone-cylinder shape forebody. The basic cross design was modified with the addition of a circumferential constraining band at the lower edge of the canopy panels. The tests covered a Mach number range of 0.3 to 1.2 and a dynamic pressure range from 479 Newtons per square meter to 5746 Newtons per square meter. The parachute models were flexible textile-type structures and were tethered to a rigid forebody with a single flexible riser. Different size models of the modified cross and disk-gap-band canopies were tested to evaluate scale effects. Model reference diameters were 0.30, 0.61, and 1.07 meters (1.0, 2.0, and 3.5 ft) for the modified cross; and nominal diameters of 0.25 and 0.52 meter (0.83 and 1.7 ft) for the disk-gap-band; and 0.55 meter (1.8 ft) for the hemisflo. Reefing information is presented for the 0.61-meter-diameter cross and the 0.52-meter-diameter disk-gap-band. Results are presented in the form of the variation of steady-state average drag coefficient with Mach number. General stability characteristics of each parachute are discussed. Included are comments on canopy coning, spinning, and fluttering motions.

Validation of Multibody Program to Optimize Simulated Trajectories II Parachute Simulation with Interacting Forces

Science.gov (United States)

Raiszadeh, Behzad; Queen, Eric M.; Hotchko, Nathaniel J.

2009-01-01

A capability to simulate trajectories of multiple interacting rigid bodies has been developed, tested and validated. This capability uses the Program to Optimize Simulated Trajectories II (POST 2). The standard version of POST 2 allows trajectory simulation of multiple bodies without force interaction. In the current implementation, the force interaction between the parachute and the suspended bodies has been modeled using flexible lines, allowing accurate trajectory simulation of the individual bodies in flight. The POST 2 multibody capability is intended to be general purpose and applicable to any parachute entry trajectory simulation. This research paper explains the motivation for multibody parachute simulation, discusses implementation methods, and presents validation of this capability.

Parachute and lateral propping reactions in preterm children

Directory of Open Access Journals (Sweden)

Ohlweiler Lygia

2002-01-01

Full Text Available A non-controlled, prognostic cohort study was performed with the aim of establishing markers of neurological development and defining a clinical and epidemiological profile of preterm newborns at 3, 6, 9, and 12 months of gestation-corrected age in terms of parachute and lateral propping reactions. Newborns with gestational age of up to 36 weeks and 6 days, weighing 2,000 g or less at birth, were included in the study At 6 months of age, parachute and lateral propping reactions were present in 8.1% of the patients. At 9 months, the parachute reaction was present in 87.5%, and the lateral propping reaction was present in 90% of the children. It was possible to assess parachute and lateral propping reactions in preterm children in the first year of life. Alterations in trunk-limb coordination may be evidenced in the 1st year of life through postural reactions, which are maintained as prematurity markers until school age.

Study of Pressure Oscillations in Supersonic Parachute

Science.gov (United States)

Dahal, Nimesh; Fukiba, Katsuyoshi; Mizuta, Kazuki; Maru, Yusuke

2018-04-01

Supersonic parachutes are a critical element of planetary mission whose simple structure, light-weight characteristics together with high ratio of aerodynamic drag makes them the most suitable aerodynamic decelerators. The use of parachute in supersonic flow produces complex shock/shock and wake/shock interaction giving rise to dynamic pressure oscillations. The study of supersonic parachute is difficult, because parachute has very flexible structure which makes obtaining experimental pressure data difficult. In this study, a supersonic wind tunnel test using two rigid bodies is done. The wind tunnel test was done at Mach number 3 by varying the distance between the front and rear objects, and the distance of a bundle point which divides suspension lines and a riser. The analysis of Schlieren movies revealed shock wave oscillation which was repetitive and had large pressure variation. The pressure variation differed in each case of change in distance between the front and rear objects, and the change in distance between riser and the rear object. The causes of pressure oscillation are: interaction of wake caused by front object with the shock wave, fundamental harmonic vibration of suspension lines, interference between shock waves, and the boundary layer of suspension lines.

14 CFR 65.115 - Senior parachute rigger certificate: Experience, knowledge, and skill requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Senior parachute rigger certificate... CREWMEMBERS Parachute Riggers § 65.115 Senior parachute rigger certificate: Experience, knowledge, and skill requirements. Except as provided in § 65.117, an applicant for a senior parachute rigger certificate must— (a...

Risk Factors for Parachute Injuries and Airborne Student Observations on the Parachute Ankle Brace

National Research Council Canada - National Science Library

Knapik, Joseph J; Spiess, Anita; Darakjy, Salima; Grier, Tyson; Manning, Fred; Livingston, Elaine; Swedler, David; Amoroso, Paul; Jones, Bruce H

2007-01-01

...) of the Defense Safety Oversight Council (DSOC) to evaluate the parachute ankle brace (PAB). Information provided by the questionnaire identified potential injury risk factors and comments on the PAB...

Rocket-Powered Parachutes Rescue Entire Planes

Science.gov (United States)

2010-01-01

Small Business Innovation Research (SBIR) contracts with Langley Research Center helped BRS Aerospace, of Saint Paul, Minnesota, to develop technology that has saved 246 lives to date. The company s whole aircraft parachute systems deploy in less than 1 second thanks to solid rocket motors and are capable of arresting the descent of a small aircraft, lowering it safely to the ground. BRS has sold more than 30,000 systems worldwide, and the technology is now standard equipment on many of the world s top-selling aircraft. Parachutes for larger airplanes are in the works.

Factors Affecting Planting Depth and Standing of Rice Seedling in Parachute Rice Transplanting

Science.gov (United States)

Astika, I. W.; Subrata, I. D. M.; Pramuhadi, G.

2018-05-01

Parachute rice transplanting is a simple and practical rice transplanting method. It can be done manually or mechanically, with various possible designs of machines or tools. This research aimed at quantitatively formulating related factors to the planting depth and standing of rice seedling. Parachute seedlings of rice were grown at several sizes of parachute soil bulb sizes. The trays were specially designed with a 3D printer having bulb sizes 7, 8, 9, 10 mm in square sides and 15 mm depth. At seedling ages of 8-12 days after sowing the seedling bulbs were drops into puddled soil. Soil hardness was set at 3 levels of hardness, measured in hardness index using golf ball test. Angle of dropping was set at 3 levels: 0°, 30°and 45° from the vertical axis. The height of droppings was set at 100 cm, 75 cm, and 50 cm. The relationship between bulb size, height of dropping, soil hardness, dropping angle and planting depth was formulated with ANN. Most of input variables did not significantly affect the planting depth, except that hard soil significantly differs from mild soil and soft soil. The dropping also resulted in various positions of the planted seedlings: vertical standing, sloped, and falling. However, at any position of the planted seedlings, the seedlings would recover themselves into normally vertical position. With this result, the design of planting machinery, as well as the manual planting operation, can be made easier.

Simulation of 3D parachute fluid–structure interaction based on nonlinear finite element method and preconditioning finite volume method

Directory of Open Access Journals (Sweden)

Fan Yuxin

2014-12-01

Full Text Available A fluid–structure interaction method combining a nonlinear finite element algorithm with a preconditioning finite volume method is proposed in this paper to simulate parachute transient dynamics. This method uses a three-dimensional membrane–cable fabric model to represent a parachute system at a highly folded configuration. The large shape change during parachute inflation is computed by the nonlinear Newton–Raphson iteration and the linear system equation is solved by the generalized minimal residual (GMRES method. A membrane wrinkling algorithm is also utilized to evaluate the special uniaxial tension state of membrane elements on the parachute canopy. In order to avoid large time expenses during structural nonlinear iteration, the implicit Hilber–Hughes–Taylor (HHT time integration method is employed. For the fluid dynamic simulations, the Roe and HLLC (Harten–Lax–van Leer contact scheme has been modified and extended to compute flow problems at all speeds. The lower–upper symmetric Gauss–Seidel (LU-SGS approximate factorization is applied to accelerate the numerical convergence speed. Finally, the test model of a highly folded C-9 parachute is simulated at a prescribed speed and the results show similar characteristics compared with experimental results and previous literature.

Psychophysiological response in parachute jumps, the effect of experience and type of jump.

Science.gov (United States)

Clemente-Suárez, Vicente Javier; Robles-Pérez, José Juan; Fernández-Lucas, Jesús

2017-10-01

We aimed to analyse the effect of experience and type of parachute jump on the psychophysiological responses of jumpers. We analysed blood oxygen saturation, heart rate, blood glucose, lactate and creatinkinase, leg strength, isometric hand strength, cortical arousal, specific fine motor skills, self-confidence and cognition, and somatic and state anxiety, before and after four different parachute jumps: a sport parachute jump, a manual tactical parachute jump, tandem pilots, and tandem passengers. Independently of the parachute jump, the psychophysiological responses of experienced paratroopers were not affected by the jumps, except for an increase in anaerobic metabolism. Novice parachute jumpers presented a higher psychophysiological stress response than the experienced jumpers, together with a large anticipatory anxiety response before the jump; however, this decreased after the jump, although the high physiological activation was maintained. This information could be used by civil and military paratroopers' instructors to improve their training programmes. Copyright © 2017 Elsevier Inc. All rights reserved.

Flight test of a spin parachute for use with a Super Arcas sounding rocket

Science.gov (United States)

Silbert, M. N.

1975-01-01

The development and flight testing of a specially configured 16.6 ft Disc Band Gap (DBG) Spin Parachute is discussed. The parachute is integrated with a modified Super Arcas launch vehicle. Total payload weight was 17.6 lbs including the Spin Parachute and a scientific payload, and lift-off weight was 100.3 lbs. The Super Arcas vehicle was despun from 18.4 cps. After payload separation at 244,170 ft the Spin Parachute and its payload attained a maximum spin rate of 2.4 cps. Total suspended weight of the Spin Parachute and its payload was 14.64 lbs.

SUSI 62 A ROBUST AND SAFE PARACHUTE UAV WITH LONG FLIGHT TIME AND GOOD PAYLOAD

Directory of Open Access Journals (Sweden)

H. P. Thamm

2012-09-01

Full Text Available In many research areas in the geo-sciences (erosion, land use, land cover change, etc. or applications (e.g. forest management, mining, land management etc. there is a demand for remote sensing images of a very high spatial and temporal resolution. Due to the high costs of classic aerial photo campaigns, the use of a UAV is a promising option for obtaining the desired remote sensed information at the time it is needed. However, the UAV must be easy to operate, safe, robust and should have a high payload and long flight time. For that purpose, the parachute UAV SUSI 62 was developed. It consists of a steel frame with a powerful 62 cm3 2- stroke engine and a parachute wing. The frame can be easily disassembled for transportation or to replace parts. On the frame there is a gimbal mounted sensor carrier where different sensors, standard SLR cameras and/or multi-spectral and thermal sensors can be mounted. Due to the design of the parachute, the SUSI 62 is very easy to control. Two different parachute sizes are available for different wind speed conditions. The SUSI 62 has a payload of up to 8 kg providing options to use different sensors at the same time or to extend flight duration. The SUSI 62 needs a runway of between 10 m and 50 m, depending on the wind conditions. The maximum flight speed is approximately 50 km/h. It can be operated in a wind speed of up to 6 m/s. The design of the system utilising a parachute UAV makes it comparatively safe as a failure of the electronics or the remote control only results in the UAV coming to the ground at a slow speed. The video signal from the camera, the GPS coordinates and other flight parameters are transmitted to the ground station in real time. An autopilot is available, which guarantees that the area of investigation is covered at the desired resolution and overlap. The robustly designed SUSI 62 has been used successfully in Europe, Africa and Australia for scientific projects and also for

Sub-Scale Orion Parachute Test Results from the National Full-Scale Aerodynamics Complex 80- By 120-ft Wind Tunnel

Science.gov (United States)

Anderson, Brian P.; Greathouse, James S.; Powell, Jessica M.; Ross, James C.; Schairer, Edward T.; Kushner, Laura; Porter, Barry J.; Goulding, Patrick W., II; Zwicker, Matthew L.; Mollmann, Catherine

2017-01-01

A two-week test campaign was conducted in the National Full-Scale Aerodynamics Complex 80 x 120-ft Wind Tunnel in support of Orion parachute pendulum mitigation activities. The test gathered static aerodynamic data using an instrumented, 3-tether system attached to the parachute vent in combination with an instrumented parachute riser. Dynamic data was also gathered by releasing the tether system and measuring canopy performance using photogrammetry. Several canopy configurations were tested and compared against the current Orion parachute design to understand changes in drag performance and aerodynamic stability. These configurations included canopies with varying levels and locations of geometric porosity as well as sails with increased levels of fullness. In total, 37 runs were completed for a total of 392 data points. Immediately after the end of the testing campaign a down-select decision was made based on preliminary data to support follow-on sub-scale air drop testing. A summary of a more rigorous analysis of the test data is also presented.

Parachuting behavior and predation by ants in the nettle caterpillar, Scopelodes contracta.

Science.gov (United States)

Yamazaki, Kazuo

2010-01-01

This paper documents the bizarre descending behavior from the tree crown to the ground of the larvae of the moth, Scopelodes contracta Walker (Lepidoptera: Limacodidae) and the interaction of the larva with predatory ants. S. contracta larvae infest leaves of many tree species in urban areas and orchards in Japan. Mature larvae and leaves without basal leaf parts were found under trees of four species infested with S. contracta larvae in Osaka, Japan. Individual larvae riding on leaves were observed falling from tree crowns to the ground. Many S. contracta cocoons were found in the soil below the trees two weeks after the observed parachuting. These observations indicate that S. contracta larvae parachuted to the ground where they spin their cocoons in the soil. When a larva that had just parachuted down was returned to an arboreal twig, the larva repeated the parachuting behavior. This parachuting behavior appears to be adaptive, because larvae can descend to the ground safely and with low energy cost. Worker ants of Tetramorium tsushimae Emery (Hymenoptera: Formicidae) and Pristomyrmex punctatus Mayr (Hymenoptera: Formicidae) occasionally attacked larvae on the ground before they had a chance to burrow in the soil.

A Survey of Parachute Ankle Brace Breakages

National Research Council Canada - National Science Library

Knapik, Joseph J; Spiess, Anita; Darakjy, Salima; Grier, Tyson; Manning, Fred; Livingston, Elaine; Swedler, David; Amoroso, Paul; Jones, Bruce H

2008-01-01

...) of the Defense Safety Oversight Council (DSOC) to evaluate the parachute ankle brace (PAB). Information provided by the questionnaire identified potential injury risk factors and comments on the PAB...

Effect of Parachute Jump in the Psychophysiological Response of Soldiers in Urban Combat.

Science.gov (United States)

Sánchez-Molina, Joaquín; Robles-Pérez, José J; Clemente-Suárez, Vicente J

2017-06-01

The study of organic and psychological response during combat situations has been poorly reported despite its importance for soldiers training and specific instruction, so it was proposed as aim of the present investigation to analyze the effect of a tactical parachute simulated jump in psycho-physiological response of paratroopers' warfighters during an urban combat simulation. 19 male paratroopers (31.9 ± 6.2 year old; 173.6 ± 5.3 cm; 73.8 ± 8.3 Kg) of the Spanish Army were divided in two groups: parachute jump group (n:11) that conducted a simulated parachute jump and a urban combat maneuver and a non-parachute jump group (n:8) that only conducted an urban combat maneuver. We analyzed before and after the maneuver the rated perceived exertion, legs strength manifestation, blood lactate, cortical activation, heart rate variability, blood oxygen saturation and pressure, skin temperature, fine motor skills, and anxiety state. A tactical parachute simulated jump prior to an urban combat maneuver produce significantly (p jump situation in professional Army paratroopers. Independently of the parachute jump, an urban combat maneuver produces a significant increase in rated perceived exertion, blood lactate, heart rate, legs strength, sympathetic modulation and anxiety response as well as a significant decrease in blood oxygen saturation and parasympathetic modulation.

Prolactin, thyrotropin, and growth hormone release during stress associated with parachute jumping.

Science.gov (United States)

Noel, G L; Dimond, R C; Earll, J M; Frantz, A G

1976-05-01

Prolactin, growth hormone, and thyrotropin (TSH) release during the stress of parachute jumping has been evaluated in 14 male subjects. Subjects were studied at several times before and immediately after their first military parachute jump. All three hormones had risen significantly 1 to 14 min after the jump, compared to mean levels measured immediately beforehand. Earlier studies of physical exercise by ourselves and others would suggest that emotional stress played a role in producing changes of this magnitude. We conclude that prolactin, TSH, and growth hormone are released in physiologically significant amounts in association with the stress of parachute jumping.

Supersonic Testing of 0.8 m Disk Gap Band Parachutes in the Wake of a 70 Deg Sphere Cone Entry Vehicle

Science.gov (United States)

Sengupta, Anita; Wernet, Mark; Roeder, James; Kelsch, Richard; Witkowski, Al; Jones, Thomas

2009-01-01

Supersonic wind tunnel testing of Viking-type 0.8 m Disk-Gap-Band (DGB) parachutes was conducted in the NASA Glenn Research Center 10'x10' wind-tunnel. The tests were conducted in support of the Mars Science Laboratory Parachute Decelerator System development and qualification program. The aerodynamic coupling of the entry-vehicle wake to parachute flow-field is under investigation to determine the cause and functional dependence of a supersonic canopy breathing phenomenon referred to as area oscillations, characteristic of DGB's above Mach 1.5 operation. Four percent of full-scale parachutes (0.8 m) were constructed similar to the flight-article in material and construction techniques. The parachutes were attached to a 70-deg sphere-cone entry-vehicle to simulate the Mars flight configuration. The parachutes were tested in the wind-tunnel from Mach 2 to 2.5 in a Reynolds number range of 2x105 to 1x106, representative of a Mars deployment. Three different test configurations were investigated. In the first two configurations, the parachutes were constrained horizontally through the vent region to measure canopy breathing and wake interaction for fixed trim angles of 0 and 10 degrees from the free-stream. In the third configuration the parachute was unconstrained, permitted to trim and cone, similar to free-flight (but capsule motion is constrained), varying its alignment relative to the entry-vehicle wake. Non-intrusive test diagnostics were chosen to quantify parachute performance and provide insight into the flow field structure. An in-line loadcell provided measurement of unsteady and mean drag. Shadowgraph of the upstream parachute flow field was used to capture bow-shock motion and wake coupling. Particle image velocimetry provided first and second order flow field statistics over a planar region of the flow field, just upstream of the parachute. A photogrammetric technique was used to quantify fabric motion using multiple high speed video cameras to record

PROCESSING AND ANALYSIS OF DATA OF natural experiment FOR DETERMINING THE tragectory CHARACTERISTICS OF A ROUND PARACHUTE AT HIGH ALTITUDES

Directory of Open Access Journals (Sweden)

S. V. Zhurin

2015-01-01

Full Text Available The article is devoted to the analysis of the trajectory parameters obtained during the flight experiment at the start of meteo-rocket MMP-06, to determine major parameters of motion of a round parachute at subsonic speeds in the range of altitudes from 0 to 60 km. The Reynolds number is changed in the range from 104 to1,5·106.The main parameters of the trajectory were obtained according to the experimental data. Only laboratory research on a model parachute systems in such a wide range of Reynolds numbers are found in the literature on parachute subjects. This article obtained results of flight experiment.

Parachuting plasmapheresis into the Ebola crisis | Zacharias | Africa ...

African Journals Online (AJOL)

Parachuting plasmapheresis into the Ebola crisis. ... A vehicle was pre-fitted with sophisticated equipment and airlifted to the study site (ELWA). ... Training included plasmapheresis, donor management, testing and pathogen inactivation.

Development of a Smart Release Algorithm for Mid-Air Separation of Parachute Test Articles

Science.gov (United States)

Moore, James W.

2011-01-01

The Crew Exploration Vehicle Parachute Assembly System (CPAS) project is currently developing an autonomous method to separate a capsule-shaped parachute test vehicle from an air-drop platform for use in the test program to develop and validate the parachute system for the Orion spacecraft. The CPAS project seeks to perform air-drop tests of an Orion-like boilerplate capsule. Delivery of the boilerplate capsule to the test condition has proven to be a critical and complicated task. In the current concept, the boilerplate vehicle is extracted from an aircraft on top of a Type V pallet and then separated from the pallet in mid-air. The attitude of the vehicles at separation is critical to avoiding re-contact and successfully deploying the boilerplate into a heatshield-down orientation. Neither the pallet nor the boilerplate has an active control system. However, the attitude of the mated vehicle as a function of time is somewhat predictable. CPAS engineers have designed an avionics system to monitor the attitude of the mated vehicle as it is extracted from the aircraft and command a release when the desired conditions are met. The algorithm includes contingency capabilities designed to release the test vehicle before undesirable orientations occur. The algorithm was verified with simulation and ground testing. The pre-flight development and testing is discussed and limitations of ground testing are noted. The CPAS project performed a series of three drop tests as a proof-of-concept of the release technique. These tests helped to refine the attitude instrumentation and software algorithm to be used on future tests. The drop tests are described in detail and the evolution of the release system with each test is described.

Parachute diverts ventilation fast

Energy Technology Data Exchange (ETDEWEB)

Chironis, N.P.

1990-02-01

The USBM Pittsburgh Research Center is developing a simple, inexpensive and highly effective new technique for keeping smoke and toxic gases out of intake escapeways during mine fires. The technique involves the use of a special parachute which fixes onto a roof bolt plate or strap, and is automatically inflated by incoming air. The chute thus becomes a quick-erect check curtain which leaks much less than conventional curtains. The air pressure in the intake quickly climbs, making it unlikely that any smoke from an adjacent entry would be able to migrate into the intake. 2 figs.

Ribbon and gliding type parachutes evaluated in the 7 by 10 foot transonic wind tunnel

Energy Technology Data Exchange (ETDEWEB)

Ottensoser, J.

1975-09-01

An experiment has been conducted in the NSRDC 7- x 10-foot transonic tunnel for the Sandia Corporation to evaluate various parachute parameters. The experiment consisted of three main parts: the first phase evaluated the disreefing characteristics of the various parachutes as well as the drag forces before, during, and after disreefing; the second phase measured the pressure distribution around the chute as well as the drag forces; and the final phase evaluated the disreefing and drag characteristics of gliding type parachutes. The free stream dynamic pressure varied from 65 to 500 psf. 12 figures, 1 table. (auth)

Percutaneous Implantation of A Parachute Device For Treatment of Ischemic Heart Failure

Energy Technology Data Exchange (ETDEWEB)

Cilingiroglu, Mehmet, E-mail: mcilingiroglu@yahoo.com; Rollefson, William A.; Mego, David

2013-07-15

Congestive heart failure (CHF) secondary to ischemic cardiomyopathy is associated with significant morbidity and mortality despite currently available medical therapy. The Parachute{sup TM} device is a novel left ventricular partitioning device that is delivered percutaneously in the left ventricle (LV) in patients with anteroapical regional wall motion abnormalities, dilated LV and systolic dysfunction after anterior myocardial infarction with favorable clinical and LV hemodynamic improvements post-implantation. Here, we do review the current literature and present a case of the Parachute device implantation.

Percutaneous Implantation of A Parachute Device For Treatment of Ischemic Heart Failure

International Nuclear Information System (INIS)

Cilingiroglu, Mehmet; Rollefson, William A.; Mego, David

2013-01-01

Congestive heart failure (CHF) secondary to ischemic cardiomyopathy is associated with significant morbidity and mortality despite currently available medical therapy. The Parachute TM device is a novel left ventricular partitioning device that is delivered percutaneously in the left ventricle (LV) in patients with anteroapical regional wall motion abnormalities, dilated LV and systolic dysfunction after anterior myocardial infarction with favorable clinical and LV hemodynamic improvements post-implantation. Here, we do review the current literature and present a case of the Parachute device implantation

Parachute technique for partial penectomy

Directory of Open Access Journals (Sweden)

Fernando Korkes

2010-04-01

Full Text Available PURPOSE: Penile carcinoma is a rare but mutilating malignancy. In this context, partial penectomy is the most commonly applied approach for best oncological results. We herein propose a simple modification of the classic technique of partial penectomy, for better cosmetic and functional results. TECHNIQUE: If partial penectomy is indicated, the present technique can bring additional benefits. Different from classical technique, the urethra is spatulated only ventrally. An inverted "V" skin flap with 0.5 cm of extension is sectioned ventrally. The suture is performed with vicryl 4-0 in a "parachute" fashion, beginning from the ventral portion of the urethra and the "V" flap, followed by the "V" flap angles and than by the dorsal portion of the penis. After completion of the suture, a Foley catheter and light dressing are placed for 24 hours. CONCLUSIONS: Several complex reconstructive techniques have been previously proposed, but normally require specific surgical abilities, adequate patient selection and staged procedures. We believe that these reconstructive techniques are very useful in some specific subsets of patients. However, the technique herein proposed is a simple alternative that can be applied to all men after a partial penectomy, and takes the same amount of time as that in the classic technique. In conclusion, the "parachute" technique for penile reconstruction after partial amputation not only improves the appearance of the penis, but also maintains an adequate function.

Innovations in Air Insertion (Involving Parachutes)

Science.gov (United States)

2008-03-01

loadings and different trim. .........48 Figure 16. Thermal being radiated from a ploughed field.50 Figure 17. A series of ridges can amplify a wave and...Crews," MHQ: The Quarterly Journal of Military History 10, no. Autumn 1998 (1998), 99. 5 Niedermeyer was killed in March of 1922 did parachutes...was killed on a 1998 wing suit jump, the cause was not wing suit related but rather the result of an easily preventable rigging

Asymptotic Parachute Performance Sensitivity

Science.gov (United States)

Way, David W.; Powell, Richard W.; Chen, Allen; Steltzner, Adam D.

2006-01-01

In 2010, the Mars Science Laboratory mission will pioneer the next generation of robotic Entry, Descent, and Landing systems by delivering the largest and most capable rover to date to the surface of Mars. In addition to landing more mass than any other mission to Mars, Mars Science Laboratory will also provide scientists with unprecedented access to regions of Mars that have been previously unreachable. By providing an Entry, Descent, and Landing system capable of landing at altitudes as high as 2 km above the reference gravitational equipotential surface, or areoid, as defined by the Mars Orbiting Laser Altimeter program, Mars Science Laboratory will demonstrate sufficient performance to land on 83% of the planet s surface. By contrast, the highest altitude landing to date on Mars has been the Mars Exploration Rover at 1.3 km below the areoid. The coupling of this improved altitude performance with latitude limits as large as 60 degrees off of the equator and a precise delivery to within 10 km of a surface target, will allow the science community to select the Mars Science Laboratory landing site from thousands of scientifically interesting possibilities. In meeting these requirements, Mars Science Laboratory is extending the limits of the Entry, Descent, and Landing technologies qualified by the Mars Viking, Mars Pathfinder, and Mars Exploration Rover missions. Specifically, the drag deceleration provided by a Viking-heritage 16.15 m supersonic Disk-Gap-Band parachute in the thin atmosphere of Mars is insufficient, at the altitudes and ballistic coefficients under consideration by the Mars Science Laboratory project, to maintain necessary altitude performance and timeline margin. This paper defines and discusses the asymptotic parachute performance observed in Monte Carlo simulation and performance analysis and its effect on the Mars Science Laboratory Entry, Descent, and Landing architecture.

Parachuting from fixed objects: descriptive study of 106 fatal events in BASE jumping 1981-2006.

Science.gov (United States)

Westman, A; Rosén, M; Berggren, P; Björnstig, U

2008-06-01

To analyse the characteristics of fatal incidents in fixed object sport parachuting (building, antenna, span, earth (BASE) jumping) and create a basis for prevention. Descriptive epidemiological study. Data on reported fatal injury events (n = 106) worldwide in 1981-2006 retrieved from the BASE fatality list. Human, equipment and environmental factors. Identification of typical fatal incident and injury mechanisms for each of the four fixed object types of BASE jumping (building, antenna, span, earth). Human factors included parachutist free fall instability (loss of body control before parachute deployment), free fall acrobatics and deployment failure by the parachutist. Equipment factors included pilot chute malfunction and parachute malfunction. In cliff jumping (BASE object type E), parachute opening towards the object jumped was the most frequent equipment factor. Environmental factors included poor visibility, strong or turbulent winds, cold and water. The overall annual fatality risk for all object types during the year 2002 was estimated at about one fatality per 60 participants. Participants in BASE jumping should target risk factors with training and technical interventions. The mechanisms described in this study should be used by rescue units to improve the management of incidents.

The parachute morphology as equilibrium morphology of vesicle-polymer hybrids?

NARCIS (Netherlands)

Jung, M.; Hubert, D.H.W.; Herk, van A.M.; German, A.L.

2000-01-01

Polymerisation in vesicles leads to novel polymer colloid morphologies. Two morphologies are currently reported: the triple-shell and the parachute morphology. The termodynamic analysis of these two morphologies, presented here, stresses the importance of considering interfacial energies between

32 CFR 705.32 - Aviation events and parachute demonstrations.

Science.gov (United States)

2010-07-01

... performing. What type of crowd control is planned? 5. Flight and Parachute Team demonstrations require that... the public domain is to support the recruiting aspects of the all-volunteer force concept. The... member of the public might wish to have clarified, contact Chief, Aerial Events Branch, OASD(PA), Room...

The influence of parachute-resisted sprinting on running mechanics in collegiate track athletes.

Science.gov (United States)

Paulson, Sally; Braun, William A

2011-06-01

The influence of parachute-resisted sprinting on running mechanics in collegiate track athletes. The aim of this investigation was to compare the acute effects of parachute-resisted (PR) sprinting on selected kinematic variables. Twelve collegiate sprinters (mean age 19.58 ± 1.44 years, mass 69.32 ± 14.38 kg, height 1.71 ± 9.86 m) ran a 40-yd dash under 2 conditions: PR sprint and sprint without a parachute (NC) that were recorded on a video computer system (60 Hz). Sagittal plane kinematics of the right side of the body was digitized to calculate joint angles at initial ground contact (IGC) and end ground contact (EGC), ground contact (GC) time, stride rate (SR), stride length (SL), and the times of the 40-yd dashes. The NC 40-yd dash time was significantly faster than the PR trial (p 0.05). This study suggests that PR sprinting does not acutely affect GC time, SR, SL and upper extremity or lower extremity joint angles during weight acceptance (IGC) in collegiate sprinters. However, PR sprinting increased shoulder flexion by 23.5% at push-off and decreased speed by 4.4%. While sprinting with the parachute, the athlete's movement patterns resembled their mechanics during the unloaded condition. This indicates the external load caused by PR did not substantially overload the runner, and only caused a minor change in the shoulder during push-off. This sports-specific training apparatus may provide coaches with another method for training athletes in a sports-specific manner without causing acute changes to running mechanics.

An Innovative High Fidelity Multidisciplinary Computational Framework for Parachute Inflation Dynamics

Data.gov (United States)

National Aeronautics and Space Administration — Current technology for decelerating a spacecraft from the high speed of atmospheric entry to the final stages of landing on Mars is based on parachute systems. It...

Cirrus Airframe Parachute System and Odds of a Fatal Accident in Cirrus Aircraft Crashes.

Science.gov (United States)

Alaziz, Mustafa; Stolfi, Adrienne; Olson, Dean M

2017-06-01

General aviation (GA) accidents have continued to demonstrate high fatality rates. Recently, ballistic parachute recovery systems (BPRS) have been introduced as a safety feature in some GA aircraft. This study evaluates the effectiveness and associated factors of the Cirrus Airframe Parachute System (CAPS) at reducing the odds of a fatal accident in Cirrus aircraft crashes. Publicly available Cirrus aircraft crash reports were obtained from the National Transportation Safety Board (NTSB) database for the period of January 1, 2001-December 31, 2016. Accident metrics were evaluated through univariate and multivariate analyses regarding odds of a fatal accident and use of the parachute system. Included in the study were 268 accidents. For CAPS nondeployed accidents, 82 of 211 (38.9%) were fatal as compared to 8 of 57 (14.0%) for CAPS deployed accidents. After controlling for all other factors, the adjusted odds ratio for a fatal accident when CAPS was not deployed was 13.1. The substantial increased odds of a fatal accident when CAPS was not deployed demonstrated the effectiveness of CAPS at providing protection of occupants during an accident. Injuries were shifted from fatal to serious or minor with the use of CAPS and postcrash fires were significantly reduced. These results suggest that BPRS could play a significant role in the next major advance in improving GA accident survival.Alaziz M, Stolfi A, Olson DM. Cirrus Airframe Parachute System and odds of a fatal accident in Cirrus aircraft crashes. Aerosp Med Hum Perform. 2017; 88(6):556-564.

Self-socialization: a case study of a parachute child.

Science.gov (United States)

Newman, Philip R; Newman, Barbara M

2009-01-01

The theoretical concept of self-socialization suggests that an individual is able to reflect on the self, formulate a vision of a future self, set goals, and take actions that create or alter the developmental trajectory. This case study of a parachute child illustrates how a person constructs her life from a very young age, drawing on a profound capacity for personal agency to overcome obstacles, identify resources, and internalize values to build a life structure. A model of the psychosocial process of self-socialization emerges from this case. Following the disruption of a well-defined trajectory, self-socialization is observed as a sequence of actions, reflection, correction, and new actions. Self-socialization is possible when a strong sense of self-efficacy is applied to attaining internalized values and goals.

Airborne Priapism: A Case of Nonischemic Priapism After Military Static-Line Parachute Injury.

Science.gov (United States)

Charny, Grigory; Booms, Zachary; McDonough, Patrick; Schauer, Steven

2015-07-01

We report the case of a 21-year-old active duty U.S. Army soldier with painful and nonresolving priapism following blunt pelvic and lower extremity trauma from military static-line parachute injury during training. The patient's condition was initially managed with corporal aspiration and intracavernosal injections of phenylephrine that provided temporary relief but recurrence soon after. Referral to Urology at the site of the patient's injury yielded a diagnosis of penile hematoma. On subsequent evaluation by Urology on return to the patient's home duty station (over 96 hours after injury, with symptoms persisting), the corpora cavernosa were rigid, the corpus spongiosum was soft, and corporal blood gas drawn by the emergency department consistent with arterial blood. Penile duplex ultrasound revealed an isolated arterial-cavernosal fistula within the proximal left corporal body. The patient underwent percutaneous embolization of the fistula with successful resolution of his condition and return of normal erectile function. We discuss this unique case of high-flow priapism occurring after blunt trauma from military parachute injury and review suggested management in a stepwise fashion. The case is significant in that extensive literature review yields no previously described case of priapism following trauma from military parachute injury. Reprint & Copyright © 2015 Association of Military Surgeons of the U.S.

PROCESSING AND ANALYSIS OF Fligh experiment DATA FOR DETERMINING THE CHARACTERISTICS OF THE MOTION OF A ROUND PARACHUTE on a spiral trajectory AT HIGH ALTITUDES

Directory of Open Access Journals (Sweden)

S. V. Zhurin

2015-01-01

Full Text Available The article is addressed to the analysis of the trajectory parameters and videos obtained during the flight experiment at the launch of meteo-rocket MMP-06 with the purpose to determine major parameters of motion of a round parachute at subsonic speeds in the range of altitudes from 0 to 40 km. The data analysis showed that the trajectory of the parachute represents spiral "stretched" by the wind in the horizontal direction and disturbed by random factors of a non-stationary flow around the parachute. The main parameters of the trajectory are obtained according to the experimental data. Only qualitative analysis of spiral motion paths for round parachutes may be found in the publications on parachute subjects. This article presents the quantitative characteristics of this process.

Design of a Modular Monolithic Implicit Solver for Multi-Physics Applications

Science.gov (United States)

Carton De Wiart, Corentin; Diosady, Laslo T.; Garai, Anirban; Burgess, Nicholas; Blonigan, Patrick; Ekelschot, Dirk; Murman, Scott M.

2018-01-01

The design of a modular multi-physics high-order space-time finite-element framework is presented together with its extension to allow monolithic coupling of different physics. One of the main objectives of the framework is to perform efficient high- fidelity simulations of capsule/parachute systems. This problem requires simulating multiple physics including, but not limited to, the compressible Navier-Stokes equations, the dynamics of a moving body with mesh deformations and adaptation, the linear shell equations, non-re effective boundary conditions and wall modeling. The solver is based on high-order space-time - finite element methods. Continuous, discontinuous and C1-discontinuous Galerkin methods are implemented, allowing one to discretize various physical models. Tangent and adjoint sensitivity analysis are also targeted in order to conduct gradient-based optimization, error estimation, mesh adaptation, and flow control, adding another layer of complexity to the framework. The decisions made to tackle these challenges are presented. The discussion focuses first on the "single-physics" solver and later on its extension to the monolithic coupling of different physics. The implementation of different physics modules, relevant to the capsule/parachute system, are also presented. Finally, examples of coupled computations are presented, paving the way to the simulation of the full capsule/parachute system.

Finite element modeling of a 3D coupled foot-boot model.

Science.gov (United States)

Qiu, Tian-Xia; Teo, Ee-Chon; Yan, Ya-Bo; Lei, Wei

2011-12-01

Increasingly, musculoskeletal models of the human body are used as powerful tools to study biological structures. The lower limb, and in particular the foot, is of interest because it is the primary physical interaction between the body and the environment during locomotion. The goal of this paper is to adopt the finite element (FE) modeling and analysis approaches to create a state-of-the-art 3D coupled foot-boot model for future studies on biomechanical investigation of stress injury mechanism, foot wear design and parachute landing fall simulation. In the modeling process, the foot-ankle model with lower leg was developed based on Computed Tomography (CT) images using ScanIP, Surfacer and ANSYS. Then, the boot was represented by assembling the FE models of upper, insole, midsole and outsole built based on the FE model of the foot-ankle, and finally the coupled foot-boot model was generated by putting together the models of the lower limb and boot. In this study, the FE model of foot and ankle was validated during balance standing. There was a good agreement in the overall patterns of predicted and measured plantar pressure distribution published in literature. The coupled foot-boot model will be fully validated in the subsequent works under both static and dynamic loading conditions for further studies on injuries investigation in military and sports, foot wear design and characteristics of parachute landing impact in military. Copyright © 2011 IPEM. Published by Elsevier Ltd. All rights reserved.

Extrapolating the Trends of Test Drop Data with Opening Shock Factor Calculations: the Case of the Orion Main and Drogue Parachutes Inflating to 1st Reefed Stage

Science.gov (United States)

Potvin, Jean; Ray, Eric

2017-01-01

We describe a new calculation of the opening shock factor C (sub k) characterizing the inflation performance of NASA's Orion spacecraft main and drogue parachutes opening under a reefing constraint (1st stage reefing), as currently tested in the Capsule Parachute Assembly System (CPAS) program. This calculation is based on an application of the Momentum-Impulse Theorem at low mass ratio (R (sub m) is less than 10 (sup -1)) and on an earlier analysis of the opening performance of drogues decelerating point masses and inflating along horizontal trajectories. Herein we extend the reach of the Theorem to include the effects of payload drag and gravitational impulse during near-vertical motion - both important pre-requisites for CPAS parachute analysis. The result is a family of C (sub k) versus R (sub m) curves which can be used for extrapolating beyond the drop-tested envelope. The paper proves this claim in the case of the CPAS Mains and Drogues opening while trailing either a Parachute Compartment Drop Test Vehicle or a Parachute Test Vehicle (an Orion capsule boiler plate). It is seen that in all cases the values of the opening shock factor can be extrapolated over a range in mass ratio that is at least twice that of the test drop data.

Freestyle swimming technique variations using a parachute Variaciones en la técnica de crol durante el nado resistido con paracaídas

Directory of Open Access Journals (Sweden)

J.M. García

2010-09-01

Full Text Available

The appearance of new assistance materials like the parachute make it necessary for coaches to know about the impact that such devices have in swimming. To study this theme 16 national and international swimmers between 19 and 24 years old have been selected. The swimmers participated in four tests that consisted in freestyle (crawl stroke swimming for 10 and 45 seconds at maximum intensity, both with and without the parachute. These tests analysed stroke frequency and stroke length. A within-subjects design has been applied and a study of the facts has been made with an AVAR with repeat measures. The results indicate that the stroke frequency decreases (p<0.05 in the parachute swim during the 10 and 45 second tests, compared with the normal swim. It was also observed that the stroke frequency is higher (p<0.01 in the 10 second test than in the 45 second test. The stroke length is higher (p<0.01 in the normal swim test than in the parachute test. With respect to the swim periods of time, the stroke length is higher (p<0.01 in the 45 second test than in the 10 second test. The parachute swim produces important changes in stroke frequency and stroke length in both the 10 and 45 second tests in subjects swimming the freestyle at maximum intensity.
KEY WORDS: swimming, swim resistance, parachute, crawl, freestyle,. stroke frequency, stroke length.

La aparición de nuevos materiales auxiliares, como el paracaídas, hace necesario que los entrenadores conozcan las modificaciones que estos producen durante el nado. Para conseguir este objetivo se seleccionaron a 16 nadadores de nivel nacional e internacional comprendidos entre los 19 y 24 años. Éstos realizaron cuatro pruebas que consistieron en nadar a crol durante 10 y 45 segundos a máxima intensidad, utilizando el nado normal (NN y el nado resistido con paracaídas (NRCP. En estas pruebas se analizaron las variables

MISSION PROFILE AND DESIGN CHALLENGES FOR MARS LANDING EXPLORATION

Directory of Open Access Journals (Sweden)

J. Dong

2017-07-01

Full Text Available An orbiter and a descent module will be delivered to Mars in the Chinese first Mars exploration mission. The descent module is composed of a landing platform and a rover. The module will be released into the atmosphere by the orbiter and make a controlled landing on Martian surface. After landing, the rover will egress from the platform to start its science mission. The rover payloads mainly include the subsurface radar, terrain camera, multispectral camera, magnetometer, anemometer to achieve the scientific investigation of the terrain, soil characteristics, material composition, magnetic field, atmosphere, etc. The landing process is divided into three phases (entry phase, parachute descent phase and powered descent phase, which are full of risks. There exit lots of indefinite parameters and design constrain to affect the selection of the landing sites and phase switch (mortaring the parachute, separating the heat shield and cutting off the parachute. A number of new technologies (disk-gap-band parachute, guidance and navigation, etc. need to be developed. Mars and Earth have gravity and atmosphere conditions that are significantly different from one another. Meaningful environmental conditions cannot be recreated terrestrially on earth. A full-scale flight validation on earth is difficult. Therefore the end-to-end simulation and some critical subsystem test must be considered instead. The challenges above and the corresponding design solutions are introduced in this paper, which can provide reference for the Mars exploration mission.

Parachuting and pregnancy: what do we know about pregnant skydivers and the risks they are taking?

Science.gov (United States)

Ebner, Florian; Wöckel, Achim; Janni, Wolfgang; Paterson, Helen

2014-11-01

There is little medical knowledge about the risks of skydiving during pregnancy. Some national parachuting associations ask for a doctor's permission; others recommend not jumping at all during pregnancy. This article provides survey data and a literature review of pregnancy and parachuting/skydiving related issues to help the pregnant skydiver and her obstetrician make an informed decision. Survey data presented include pregnancy, delivery, and parachuting information from skydivers who jumped during pregnancy. International retrospective anonymous online questionnaire considering the Checklist for Reporting Results of Internet E-Surveys (CHERRIE). The PubMed database was searched with using the terms "skydive," "pregnancy," and "parachute" (query April 2013). Web page questionnaire on skydivers' epidemiology, experience, and pregnancy-related information. Fifty-seven parous female skydivers. Information on athletes' experience, weather conditions, obstetric history (gravida, gestational week), delivery mode was obtained. Epidemiology of pregnant skydivers and literature review to provide information on skydiving risks. Women do actively decide to skydive while pregnant. The majority of our participants were between 25-year-old and 35-year-old primips with 100 to 1000 jumps experience, answering the questionnaire from a European IP address. Precautions are taken in terms of weather conditions, gear, or sports partner. The literature review found no relevant literature regarding the question. Literature is searched for risk factors that come close to the ones in skydiving (ie, oxygen saturation, shock forces, and others). Further studies are needed to show the long-term effect of stress or low O2 saturation on antenatal programming, or short-term hypoxia and pregnancy outcome in pregnant skydiving women and their offspring. Pregnancy itself is a risk factor for injuries. Injuries in pregnancy are clearly associated with an unfavorable pregnancy outcome. The

X-Ray Micro-Tomography Applied to Nasa's Materials Research: Heat Shields, Parachutes and Asteroids

Science.gov (United States)

Panerai, Francesco; Borner, Arnaud; Ferguson, Joseph C.; Mansour, Nagi N.; Stern, Eric C.; Barnard, Harold S.; Macdowell, Alastair A.; Parkinson, Dilworth Y.

2017-01-01

X-ray micro-tomography is used to support the research on materials carried out at NASA Ames Research Center. The technique is applied to a variety of applications, including the ability to characterize heat shield materials for planetary entry, to study the Earth- impacting asteroids, and to improve broadcloths of spacecraft parachutes. From micro-tomography images, relevant morphological and transport properties are determined and validated against experimental data.

Automated scheme to determine design parameters for a recoverable reentry vehicle

International Nuclear Information System (INIS)

Williamson, W.E.

1976-01-01

The NRV (Nosetip Recovery Vehicle) program at Sandia Laboratories is designed to recover the nose section from a sphere cone reentry vehicle after it has flown a near ICBM reentry trajectory. Both mass jettison and parachutes are used to reduce the velocity of the RV near the end of the trajectory to a sufficiently low level that the vehicle may land intact. The design problem of determining mass jettison time and parachute deployment time in order to ensure that the vehicle does land intact is considered. The problem is formulated as a min-max optimization problem where the design parameters are to be selected to minimize the maximum possible deviation in the design criteria due to uncertainties in the system. The results of the study indicate that the optimal choice of the design parameters ensures that the maximum deviation in the design criteria is within acceptable bounds. This analytically ensures the feasibility of recovery for NRV

Influencing Factors of the Initiation Point in the Parachute-Bomb Dynamic Detonation System

Science.gov (United States)

Qizhong, Li; Ye, Wang; Zhongqi, Wang; Chunhua, Bai

2017-12-01

The parachute system has been widely applied in modern armament design, especially for the fuel-air explosives. Because detonation of fuel-air explosives occurs during flight, it is necessary to investigate the influences of the initiation point to ensure successful dynamic detonation. In fact, the initiating position exist the falling area in the fuels, due to the error of influencing factors. In this paper, the major influencing factors of initiation point were explored with airdrop and the regularity between initiation point area and factors were obtained. Based on the regularity, the volume equation of initiation point area was established to predict the range of initiation point in the fuel. The analysis results showed that the initiation point appeared area, scattered on account of the error of attitude angle, secondary initiation charge velocity, and delay time. The attitude angle was the major influencing factors on a horizontal axis. On the contrary, secondary initiation charge velocity and delay time were the major influencing factors on a horizontal axis. Overall, the geometries of initiation point area were sector coupled with the errors of the attitude angle, secondary initiation charge velocity, and delay time.

Mars Exploration Rover Terminal Descent Mission Modeling and Simulation

Science.gov (United States)

Raiszadeh, Behzad; Queen, Eric M.

2004-01-01

Because of NASA's added reliance on simulation for successful interplanetary missions, the MER mission has developed a detailed EDL trajectory modeling and simulation. This paper summarizes how the MER EDL sequence of events are modeled, verification of the methods used, and the inputs. This simulation is built upon a multibody parachute trajectory simulation tool that has been developed in POST I1 that accurately simulates the trajectory of multiple vehicles in flight with interacting forces. In this model the parachute and the suspended bodies are treated as 6 Degree-of-Freedom (6 DOF) bodies. The terminal descent phase of the mission consists of several Entry, Descent, Landing (EDL) events, such as parachute deployment, heatshield separation, deployment of the lander from the backshell, deployment of the airbags, RAD firings, TIRS firings, etc. For an accurate, reliable simulation these events need to be modeled seamlessly and robustly so that the simulations will remain numerically stable during Monte-Carlo simulations. This paper also summarizes how the events have been modeled, the numerical issues, and modeling challenges.

Low Density Supersonic Decelerator Flight Dynamics Test-1 Flight Design and Targeting

Science.gov (United States)

Ivanov, Mark

2015-01-01

NASA's Low Density Supersonic Decelerator (LDSD) program was established to identify, develop, and eventually qualify to Test [i.e. Technology] Readiness Level (TRL) - 6 aerodynamic decelerators for eventual use on Mars. Through comprehensive Mars application studies, two distinct Supersonic Inflatable Aerodynamic Decelerator (SIAD) designs were chosen that afforded the optimum balance of benefit, cost, and development risk. In addition, a Supersonic Disk Sail (SSDS) parachute design was chosen that satisfied the same criteria. The final phase of the multi-tiered qualification process involves Earth Supersonic Flight Dynamics Tests (SFDTs) within environmental conditions similar to those that would be experienced during a Mars Entry, Descent, and Landing (EDL) mission. The first of these flight tests (i.e. SFDT-1) was completed on June 28, 2014 with two more tests scheduled for the summer of 2015 and 2016, respectively. The basic flight design for all the SFDT flights is for the SFDT test vehicle to be ferried to a float altitude of 120 kilo-feet by a 34 thousand cubic feet (Mcf) heavy lift helium balloon. Once float altitude is reached, the test vehicle is released from the balloon, spun-up for stability, and accelerated to supersonic speeds using a Star48 solid rocket motor. After burnout of the Star48 motor the vehicle decelerates to pre-flight selected test conditions for the deployment of the SIAD system. After further deceleration with the SIAD deployed, the SSDS parachute is then deployed stressing the performance of the parachute in the wake of the SIAD augmented blunt body. The test vehicle/SIAD/parachute system then descends to splashdown in the Pacific Ocean for eventual recovery. This paper will discuss the development of both the test vehicle and the trajectory sequence including design trade-offs resulting from the interaction of both engineering efforts. In addition, the SFDT-1 nominal trajectory design and associated sensitivities will be discussed

A influência de palmares e parachute na coordenação dos nados

OpenAIRE

Thiago Telles

2012-01-01

Resumo: A natação é uma modalidade esportiva que, ao longo dos anos, sofreu modificações, atingindo um alto nível de exigência, o que é refletido nas sessões de treinamentos e nas pesquisas sobre a modalidade. Sendo assim, para otimizar o deslocamento nos nadadores pode-se otimizar a força propulsora. Para isso, pode-se utilizar palmares e parachute. Os palmares tem como função promover o aumento artificial da área da mão, desta maneira, aumenta-se a área frontal da mão do sujeito em contato ...

Orion Multi-Purpose Crew Vehicle Solving and Mitigating the Two Main Cluster Pendulum Problem

Science.gov (United States)

Ali, Yasmin; Sommer, Bruce; Troung, Tuan; Anderson, Brian; Madsen, Christopher

2017-01-01

The Orion Multi-purpose Crew Vehicle (MPCV) Orion spacecraft will return humans from beyond earth's orbit, including Mars and will be required to land 20,000 pounds of mass safely in the ocean. The parachute system nominally lands under 3 main parachutes, but the system is designed to be fault tolerant and land under 2 main parachutes. During several of the parachute development tests, it was observed that a pendulum, or swinging, motion could develop while the Crew Module (CM) was descending under two parachutes. This pendulum effect had not been previously predicted by modeling. Landing impact analysis showed that the landing loads would double in some places across the spacecraft. The CM structural design limits would be exceeded upon landing if this pendulum motion were to occur. The Orion descent and landing team was faced with potentially millions of dollars in structural modifications and a severe mass increase. A multidisciplinary team was formed to determine root cause, model the pendulum motion, study alternate canopy planforms and assess alternate operational vehicle controls & operations providing mitigation options resulting in a reliability level deemed safe for human spaceflight. The problem and solution is a balance of risk to a known solution versus a chance to improve the landing performance for the next human-rated spacecraft.

Efeitos do treinamento de força específico no desempenho de nadadores velocistas treinados com parachute

Directory of Open Access Journals (Sweden)

Danilo Sales Bocalini

2010-09-01

Full Text Available OBJETIVO: verificar os efeitos do treinamento de força específico no desempenho de nadadores velocistas. METODOLOGIA: dois grupos de nadadores randomizados em treinados sem (TSP, n: 8 e com parachute (TCP, n: 12 foram submetidos a treinamento de 12 semanas (6 x semana; 1 sessão de 2 h/dia, sendo avaliados a força muscular (FMMI; a força específica (FE e o tempo de sustentação de força (TSF; o número de braçadas em 50m (NB 50m; o tempo e a velocidade de nado em 15 (V 15m e 50m (V 50m, antes e após o protocolo. RESULTADOS: após o programa de treinamento, não ocorreram modificações na FMMI e V 15m para ambos os grupos. Nas demais variáveis houve melhora significante (p 18%; FE (> 30%; TSF (> 35%; NB 50m ( 16%. O grupo TSP apresentou melhora no TSF (> 9%. CONCLUSÃO: o emprego do parachute foi eficiente em melhorar os parâmetros de força e no desempenho no teste de 50m

The PARAChute Project: Remote Monitoring of Posture and Gait for Fall Prevention

Science.gov (United States)

Hewson, David J.; Duchêne, Jacques; Charpillet, François; Saboune, Jamal; Michel-Pellegrino, Valérie; Amoud, Hassan; Doussot, Michel; Paysant, Jean; Boyer, Anne; Hogrel, Jean-Yves

2007-12-01

Falls in the elderly are a major public health problem due to both their frequency and their medical and social consequences. In France alone, more than two million people aged over 65 years old fall each year, leading to more than 9 000 deaths, in particular in those over 75 years old (more than 8 000 deaths). This paper describes the PARAChute project, which aims to develop a methodology that will enable the detection of an increased risk of falling in community-dwelling elderly. The methods used for a remote noninvasive assessment for static and dynamic balance assessments and gait analysis are described. The final result of the project has been the development of an algorithm for movement detection during gait and a balance signature extracted from a force plate. A multicentre longitudinal evaluation of balance has commenced in order to validate the methodologies and technologies developed in the project.

The PARAChute Project: Remote Monitoring of Posture and Gait for Fall Prevention

Directory of Open Access Journals (Sweden)

Anne Boyer

2007-01-01

Full Text Available Falls in the elderly are a major public health problem due to both their frequency and their medical and social consequences. In France alone, more than two million people aged over 65 years old fall each year, leading to more than 9 000 deaths, in particular in those over 75 years old (more than 8 000 deaths. This paper describes the PARAChute project, which aims to develop a methodology that will enable the detection of an increased risk of falling in community-dwelling elderly. The methods used for a remote noninvasive assessment for static and dynamic balance assessments and gait analysis are described. The final result of the project has been the development of an algorithm for movement detection during gait and a balance signature extracted from a force plate. A multicentre longitudinal evaluation of balance has commenced in order to validate the methodologies and technologies developed in the project.

Parachute Recovery Systems Design Manual

Science.gov (United States)

1991-03-01

Decelerators Operating at High Altitudes and High Mach Numbers, by W E. Nikel and W M. Gran. USAF, July 1964. (USAF Report FDL-TDR-64-35.) 5-139 NWC TP...CUTTER BLADE ’S ACTUATOR ASSEMBLY ASSEMBL WELDED CLOSURE DISK LINE BORON/CALCIUM CHROMATE 1OHM BRIDGE -. (47gm Dia. Wire Tophet C) DAP RING POLVIMIDE...thread used in woven metals such as metal shielding for electrical wiring . All other man-made fibers are based on cellulose, protein, or resin composites

Modelling in Business Model design

NARCIS (Netherlands)

Simonse, W.L.

2013-01-01

It appears that business model design might not always produce a design or model as the expected result. However when designers are involved, a visual model or artefact is produced. To assist strategic managers in thinking about how they can act, the designers challenge is to combine strategy and

Effectiveness of Technological Design on Elementary Student Teachers' Understanding of Air Resistance, Gravity, Terminal Velocity and Acceleration: Model Parachute Race Activity

Science.gov (United States)

Aydin, Mirac; Bakirci, Hasan; Artun, Huseyin; Cepni, Salih

2013-01-01

Educational research maintains that, teaching science through designing technology has significant educational potential. Although the literature emphasizes that making technological designs is beneficial for students, it is stressed that studies about technological design generally focus on mental structures rather than hand skills of students…

Free-Spinning Characteristics of a 1/24-Scale Model of the Grumman F11F-1 Airplane, TED No. NACA AD 395

Science.gov (United States)

Bowman, James S., Jr.

1955-01-01

An investigation is being conducted in the Langley 20-foot free-spinning tunnel on a 1/24-scale model of the Grumman F11F-1 airplane to determine spin and recovery characteristics and the minimum-size parachute required to satisfactorily terminate the spin in an emergency. Results obtained to date are presented herein. Test results indicate that it may be difficult to obtain an erect or inverted spin on the airplane, but, if a spin is obtained, the spin will be very oscillatory and recovery from the developed erect spin by rudder reversal may not be possible. The lateral controls will have no appreciable effect on recoveries from erect.spins. Recovery from the inverted spin by merely neutralizing the rudder will be satisfactory. After recoveries by rudder reversal and after recoveries from spins without control movement (no spins), the model oftentimes rolled very rapidly about the X-axis. Based on limited preliminary tests made in this investigation to make the model recover satisfactorily, it appears that canards near the nose of the airplane or differentially operated horizontal tails may be utilized to provide rapid recoveries. The parachute test results indicate that an 11-foot-diameter (laid-out-flat) parachute with a drag coefficient of 0.650 (based on the laid- out-flat diameter) and with a towline length equal to the wing span is the minimum-size parachute required to satisfactorily terminate an erect or inverted spin in an emergency.

Summary of CPAS EDU Testing Analysis Results

Science.gov (United States)

Romero, Leah M.; Bledsoe, Kristin J.; Davidson, John.; Engert, Meagan E.; Fraire, Usbaldo, Jr.; Galaviz, Fernando S.; Galvin, Patrick J.; Ray, Eric S.; Varela, Jose

2015-01-01

The Orion program's Capsule Parachute Assembly System (CPAS) project is currently conducting its third generation of testing, the Engineering Development Unit (EDU) series. This series utilizes two test articles, a dart-shaped Parachute Compartment Drop Test Vehicle (PCDTV) and capsule-shaped Parachute Test Vehicle (PTV), both of which include a full size, flight-like parachute system and require a pallet delivery system for aircraft extraction. To date, 15 tests have been completed, including six with PCDTVs and nine with PTVs. Two of the PTV tests included the Forward Bay Cover (FBC) provided by Lockheed Martin. Advancements in modeling techniques applicable to parachute fly-out, vehicle rate of descent, torque, and load train, also occurred during the EDU testing series. An upgrade from a composite to an independent parachute simulation allowed parachute modeling at a higher level of fidelity than during previous generations. The complexity of separating the test vehicles from their pallet delivery systems necessitated the use the Automatic Dynamic Analysis of Mechanical Systems (ADAMS) simulator for modeling mated vehicle aircraft extraction and separation. This paper gives an overview of each EDU test and summarizes the development of CPAS analysis tools and techniques during EDU testing.

Parachute Creek Shale Oil Program Environmental Monitoring Program. Quarterly report, fourth quarter, October 1-December 31, 1991

International Nuclear Information System (INIS)

1992-01-01

The Energy Security Act of 1980 established a program to provide financial assistance to private industry in the construction and operation of commercial-scale synthetic fuels plants. The Parachute Creek Shale Oil Program is one of four projects awarded financial assistance. The Program agreed to comply with existing environmental monitoring regulations and to develop an Environmental Monitoring Plan (EMP) incorporating supplemental monitoring in the areas of water, air, solid waste, and worker health and safety during the period 1985-1992. These activities are described in a series of quarterly and annual reports. The document contains environmental compliance data collected in the fourth quarter of 1991, contents of reports on compliance data submitted to regulatory agencies, and supplemental analytical results from retorted shale pile runoff water collected following a storm event during the third quarter of 1991

Database modeling and design logical design

CERN Document Server

Teorey, Toby J; Nadeau, Tom; Jagadish, HV

2011-01-01

Database systems and database design technology have undergone significant evolution in recent years. The relational data model and relational database systems dominate business applications; in turn, they are extended by other technologies like data warehousing, OLAP, and data mining. How do you model and design your database application in consideration of new technology or new business needs? In the extensively revised fifth edition, you'll get clear explanations, lots of terrific examples and an illustrative case, and the really practical advice you have come to count on--with design rules

Database modeling and design logical design

CERN Document Server

Teorey, Toby J; Nadeau, Tom; Jagadish, HV

2005-01-01

Database systems and database design technology have undergone significant evolution in recent years. The relational data model and relational database systems dominate business applications; in turn, they are extended by other technologies like data warehousing, OLAP, and data mining. How do you model and design your database application in consideration of new technology or new business needs? In the extensively revised fourth edition, you'll get clear explanations, lots of terrific examples and an illustrative case, and the really practical advice you have come to count on--with design rul

Disturbance observer based model predictive control for accurate atmospheric entry of spacecraft

Science.gov (United States)

Wu, Chao; Yang, Jun; Li, Shihua; Li, Qi; Guo, Lei

2018-05-01

Facing the complex aerodynamic environment of Mars atmosphere, a composite atmospheric entry trajectory tracking strategy is investigated in this paper. External disturbances, initial states uncertainties and aerodynamic parameters uncertainties are the main problems. The composite strategy is designed to solve these problems and improve the accuracy of Mars atmospheric entry. This strategy includes a model predictive control for optimized trajectory tracking performance, as well as a disturbance observer based feedforward compensation for external disturbances and uncertainties attenuation. 500-run Monte Carlo simulations show that the proposed composite control scheme achieves more precise Mars atmospheric entry (3.8 km parachute deployment point distribution error) than the baseline control scheme (8.4 km) and integral control scheme (5.8 km).

Models in architectural design

OpenAIRE

Pauwels, Pieter

2017-01-01

Whereas architects and construction specialists used to rely mainly on sketches and physical models as representations of their own cognitive design models, they rely now more and more on computer models. Parametric models, generative models, as-built models, building information models (BIM), and so forth, they are used daily by any practitioner in architectural design and construction. Although processes of abstraction and the actual architectural model-based reasoning itself of course rema...

Unocal Parachute Creek Shale Oil Program Environmental Monitoring Program. Annual report, October 1, 1990-December 31, 1991

International Nuclear Information System (INIS)

1992-01-01

The Energy Security Act of 1980 established a program to provide financial assistance to private industry in the construction and operation of commercial-scale synthetic fuels plants. The Parachute Creek Shale Oil Program is one of four projects awarded financial assistance. The Program agreed to comply with existing environmental monitoring regulations and to develop an Environmental Monitoring Plan (EMP) incorporating supplemental monitoring in the areas of water, air, solid waste, and worker health and safety during the period 1985-1992. These activities are described in a series of quarterly and annual reports. The report contains summaries of compliance and supplemental environmental and industrial hygiene and health surveillance monitoring conducted during the period; compliance permits, permit changes, and Notices of Violations discussions; statistical significance of Employee General Health information, medical histories, physical exams, pulmonary functions, clinical tests and demographics; independent audit reports; and a description of retorted shale disposal activities

Designing Business Model Change

DEFF Research Database (Denmark)

Cavalcante, Sergio Andre

2014-01-01

The aim of this paper is to base organisational change on the firm's business model, an approach that research has only recently start to address. This study adopts a process-based perspective on business models and insights from a variety of theories as the basis for the development of ideas...... on the design of business model change. This paper offers a new, process-based strategic analytical artefact for the design of business model change, consisting of three main phases. Designing business model change as suggested in this paper allows ex ante analysis of alternative scenarios of change...

Designer's unified cost model

Science.gov (United States)

Freeman, William T.; Ilcewicz, L. B.; Swanson, G. D.; Gutowski, T.

1992-01-01

A conceptual and preliminary designers' cost prediction model has been initiated. The model will provide a technically sound method for evaluating the relative cost of different composite structural designs, fabrication processes, and assembly methods that can be compared to equivalent metallic parts or assemblies. The feasibility of developing cost prediction software in a modular form for interfacing with state of the art preliminary design tools and computer aided design programs is being evaluated. The goal of this task is to establish theoretical cost functions that relate geometric design features to summed material cost and labor content in terms of process mechanics and physics. The output of the designers' present analytical tools will be input for the designers' cost prediction model to provide the designer with a data base and deterministic cost methodology that allows one to trade and synthesize designs with both cost and weight as objective functions for optimization. The approach, goals, plans, and progress is presented for development of COSTADE (Cost Optimization Software for Transport Aircraft Design Evaluation).

Co-designing business models

DEFF Research Database (Denmark)

Gudiksen, Sune Klok

2015-01-01

in a system, product or service for a particular end-user. In this dissertation, co-design and design games enter a new frontier - business models - and move towards being a part of a broader innovation agenda. The research deals with a double concern: First, the transfer of co-design and the subfield design...... games into business model experimentation to investigate how this might be useful in this new application domain. Second, investigate what can be added to the transferring field co-design, hereunder especially design games. The research into this double concern is conducted through an approach assembled...... of business cases and games are investigated through video interaction analysis, observations during the activities, and evaluation rounds. Central to the first concern in this research is that in innovation studies and in business practises the notion of business model experimentation is becoming...

Designers' unified cost model

Science.gov (United States)

Freeman, W.; Ilcewicz, L.; Swanson, G.; Gutowski, T.

1992-01-01

The Structures Technology Program Office (STPO) at NASA LaRC has initiated development of a conceptual and preliminary designers' cost prediction model. The model will provide a technically sound method for evaluating the relative cost of different composite structural designs, fabrication processes, and assembly methods that can be compared to equivalent metallic parts or assemblies. The feasibility of developing cost prediction software in a modular form for interfacing with state-of-the-art preliminary design tools and computer aided design programs is being evaluated. The goal of this task is to establish theoretical cost functions that relate geometric design features to summed material cost and labor content in terms of process mechanics and physics. The output of the designers' present analytical tools will be input for the designers' cost prediction model to provide the designer with a database and deterministic cost methodology that allows one to trade and synthesize designs with both cost and weight as objective functions for optimization. This paper presents the team members, approach, goals, plans, and progress to date for development of COSTADE (Cost Optimization Software for Transport Aircraft Design Evaluation).

SLS Navigation Model-Based Design Approach

Science.gov (United States)

Oliver, T. Emerson; Anzalone, Evan; Geohagan, Kevin; Bernard, Bill; Park, Thomas

2018-01-01

The SLS Program chose to implement a Model-based Design and Model-based Requirements approach for managing component design information and system requirements. This approach differs from previous large-scale design efforts at Marshall Space Flight Center where design documentation alone conveyed information required for vehicle design and analysis and where extensive requirements sets were used to scope and constrain the design. The SLS Navigation Team has been responsible for the Program-controlled Design Math Models (DMMs) which describe and represent the performance of the Inertial Navigation System (INS) and the Rate Gyro Assemblies (RGAs) used by Guidance, Navigation, and Controls (GN&C). The SLS Navigation Team is also responsible for the navigation algorithms. The navigation algorithms are delivered for implementation on the flight hardware as a DMM. For the SLS Block 1-B design, the additional GPS Receiver hardware is managed as a DMM at the vehicle design level. This paper provides a discussion of the processes and methods used to engineer, design, and coordinate engineering trades and performance assessments using SLS practices as applied to the GN&C system, with a particular focus on the Navigation components. These include composing system requirements, requirements verification, model development, model verification and validation, and modeling and analysis approaches. The Model-based Design and Requirements approach does not reduce the effort associated with the design process versus previous processes used at Marshall Space Flight Center. Instead, the approach takes advantage of overlap between the requirements development and management process, and the design and analysis process by efficiently combining the control (i.e. the requirement) and the design mechanisms. The design mechanism is the representation of the component behavior and performance in design and analysis tools. The focus in the early design process shifts from the development and

Unocal Parachute Creek Shale Oil Program. Environmental Monitoring Plan quarterly report. Fourth quarter, 1989. Rept. for 1 Oct-31 Dec 89

International Nuclear Information System (INIS)

1990-01-01

The Energy Security Act of 1980 established a program to provide financial assistance to private industry in the construction and operation of commerical-scale synthetic fuels plants. The Parachute Creek Shale Oil Program is one of four projects awarded financial assistance. The Program agreed to comply with existing environmental monitoring regulations and to develop an Environmental Monitoring Plan incorporating supplemental monitoring in the areas of water, air, solid waste, and worker health and safety during the period 1985-1992. These activities are described in a series of quarterly and annual reports. The report contains environmental compliance data reports, results of industrial hygiene compliance monitoring, and independent audits. Table 2-1 shows 14 of the 20 supplemental monitoring sites sampled during the quarter

Computational Design Modelling : Proceedings of the Design Modelling Symposium

CERN Document Server

Kilian, Axel; Palz, Norbert; Scheurer, Fabian

2012-01-01

This book publishes the peer-reviewed proceeding of the third Design Modeling Symposium Berlin . The conference constitutes a platform for dialogue on experimental practice and research within the field of computationally informed architectural design. More than 60 leading experts the computational processes within the field of computationally informed architectural design to develop a broader and less exotic building practice that bears more subtle but powerful traces of the complex tool set and approaches we have developed and studied over recent years. The outcome are new strategies for a reasonable and innovative implementation of digital potential in truly innovative and radical design guided by both responsibility towards processes and the consequences they initiate.

Subgrade design models

CSIR Research Space (South Africa)

Theyse, HL

2002-02-01

Full Text Available procedure commonly used in South Africa, namely the South African Mechanistic-Empirical Design Method (SAMDM). This was achieved through the development of a new design approach and permanent deformation model for the pavement subgrade. The new distress...

Research design models: a new category

International Nuclear Information System (INIS)

Burgeson, D.A.

1983-01-01

This paper discusses the concept of a research design model and how it differs from an engineering design model. Essentially, the research design model draws on the methods, materials and processes of engineering design models but more emphasis is placed on conceptualization in 3-D. Typically, equipment and processes in research are unique. Often, there are competing concepts from which to decide. The approach which is evolving at Sandia National Laboratories mixes preliminary, engineering and research design on the same model

Military Free Fall Scheduling And Manifest Optimization Model

Science.gov (United States)

2016-12-01

zone. As interest in qualifying more personnel increased, the course expanded. By the mid-1990s, Reyes explains, a new location was required to better...Since 2005, the Chilean Professional Soccer Association has used operations research techniques to schedule professional leagues in Chile . These...a new parachute the students are using, the RA-1. The RA-1 parachute has a longer glide ratio, which means the rate of descent is slower than with

Get Ready To Fly.

Science.gov (United States)

Janes, Patricia

2001-01-01

Presents suggestions to help students learn about the concept of flight. Ideas include making a classroom timeline of flight, creating balloon rockets to demonstrate the concept of thrust, making tissue paper parachutes and observing the effect of drag, designing a space mission patch, and having a model paper airplane competition. (SM)

Model based design introduction: modeling game controllers to microprocessor architectures

Science.gov (United States)

Jungwirth, Patrick; Badawy, Abdel-Hameed

2017-04-01

We present an introduction to model based design. Model based design is a visual representation, generally a block diagram, to model and incrementally develop a complex system. Model based design is a commonly used design methodology for digital signal processing, control systems, and embedded systems. Model based design's philosophy is: to solve a problem - a step at a time. The approach can be compared to a series of steps to converge to a solution. A block diagram simulation tool allows a design to be simulated with real world measurement data. For example, if an analog control system is being upgraded to a digital control system, the analog sensor input signals can be recorded. The digital control algorithm can be simulated with the real world sensor data. The output from the simulated digital control system can then be compared to the old analog based control system. Model based design can compared to Agile software develop. The Agile software development goal is to develop working software in incremental steps. Progress is measured in completed and tested code units. Progress is measured in model based design by completed and tested blocks. We present a concept for a video game controller and then use model based design to iterate the design towards a working system. We will also describe a model based design effort to develop an OS Friendly Microprocessor Architecture based on the RISC-V.

UNOCAL Parachute Creek Shale Oil Program. Environmental Monitoring Plan - supplemental environmental. Volume 1. Trip 2 report. Rept. for 1988-90

International Nuclear Information System (INIS)

1991-01-01

The Energy Security Act of 1980 established a program to provide financial assistance to private industry in the construction and operation of commercial-scale synthetic fuels plants. The Parachute Creek Shale Oil Program is one of four projects awarded financial assistance. The Program agreed to comply with existing environmental monitoring regulations and to develop an Environmental Monitoring Plan (EMP) incorporating supplemental monitoring in the areas of water, air, solid waste, and worker health and safety during the period 1985-1992. These activities are described in a series of quarterly and annual reports. The report contains results of three years of supplemental environmental sampling (Trial Trip, 1988; Trip 1, 1989; and Trip 2, 1990); Trip 2 sampling and analytical methods; quality assurance and quality control procedures; sampling and analytical methods; and corrected data from 1988 and 1989 gas and particulate concentrations

A Model of Designing: Understanding Engineering Design Activity

DEFF Research Database (Denmark)

Ahmed, Saeema; Aurisicchio, Marco

2007-01-01

This research describes an understanding of design activity through design questions. From a number of previous studies two types of questions have been identified: 1) reasoning questions; and 2) strategic questions. Strategic questions are part of an experienced designers approach to solving a d...... solving model. An example of aerospace engineering design is used to illustrate the argument. The research contributes to an understanding of design activity....

Model-Based Engineering Design for Trade Space Exploration throughout the Design Cycle

Science.gov (United States)

Lamassoure, Elisabeth S.; Wall, Stephen D.; Easter, Robert W.

2004-01-01

This paper presents ongoing work to standardize model-based system engineering as a complement to point design development in the conceptual design phase of deep space missions. It summarizes two first steps towards practical application of this capability within the framework of concurrent engineering design teams and their customers. The first step is standard generation of system sensitivities models as the output of concurrent engineering design sessions, representing the local trade space around a point design. A review of the chosen model development process, and the results of three case study examples, demonstrate that a simple update to the concurrent engineering design process can easily capture sensitivities to key requirements. It can serve as a valuable tool to analyze design drivers and uncover breakpoints in the design. The second step is development of rough-order- of-magnitude, broad-range-of-validity design models for rapid exploration of the trade space, before selection of a point design. At least one case study demonstrated the feasibility to generate such models in a concurrent engineering session. The experiment indicated that such a capability could yield valid system-level conclusions for a trade space composed of understood elements. Ongoing efforts are assessing the practicality of developing end-to-end system-level design models for use before even convening the first concurrent engineering session, starting with modeling an end-to-end Mars architecture.

Model based process-product design and analysis

DEFF Research Database (Denmark)

Gani, Rafiqul

This paper gives a perspective on modelling and the important role it has within product-process design and analysis. Different modelling issues related to development and application of systematic model-based solution approaches for product-process design is discussed and the need for a hybrid...... model-based framework is highlighted. This framework should be able to manage knowledge-data, models, and associated methods and tools integrated with design work-flows and data-flows for specific product-process design problems. In particular, the framework needs to manage models of different types......, forms and complexity, together with their associated parameters. An example of a model-based system for design of chemicals based formulated products is also given....

Modelling and designing electric energy networks

International Nuclear Information System (INIS)

Retiere, N.

2003-11-01

The author gives an overview of his research works in the field of electric network modelling. After a brief overview of technological evolutions from the telegraph to the all-electric fly-by-wire aircraft, he reports and describes various works dealing with a simplified modelling of electric systems and with fractal simulation. Then, he outlines the challenges for the design of electric networks, proposes a design process, gives an overview of various design models, methods and tools, and reports an application in the design of electric networks for future jumbo jets

Telecommunications network modelling, planning and design

CERN Document Server

Evans, Sharon

2003-01-01

Telecommunication Network Modelling, Planning and Design addresses sophisticated modelling techniques from the perspective of the communications industry and covers some of the major issues facing telecommunications network engineers and managers today. Topics covered include network planning for transmission systems, modelling of SDH transport network structures and telecommunications network design and performance modelling, as well as network costs and ROI modelling and QoS in 3G networks.

SLS Model Based Design: A Navigation Perspective

Science.gov (United States)

Oliver, T. Emerson; Anzalone, Evan; Park, Thomas; Geohagan, Kevin

2018-01-01

The SLS Program has implemented a Model-based Design (MBD) and Model-based Requirements approach for managing component design information and system requirements. This approach differs from previous large-scale design efforts at Marshall Space Flight Center where design documentation alone conveyed information required for vehicle design and analysis and where extensive requirements sets were used to scope and constrain the design. The SLS Navigation Team is responsible for the Program-controlled Design Math Models (DMMs) which describe and represent the performance of the Inertial Navigation System (INS) and the Rate Gyro Assemblies (RGAs) used by Guidance, Navigation, and Controls (GN&C). The SLS Navigation Team is also responsible for navigation algorithms. The navigation algorithms are delivered for implementation on the flight hardware as a DMM. For the SLS Block 1B design, the additional GPS Receiver hardware model is managed as a DMM at the vehicle design level. This paper describes the models, and discusses the processes and methods used to engineer, design, and coordinate engineering trades and performance assessments using SLS practices as applied to the GN&C system, with a particular focus on the navigation components.

Design-based research in designing the model for educating simulation facilitators.

Science.gov (United States)

Koivisto, Jaana-Maija; Hannula, Leena; Bøje, Rikke Buus; Prescott, Stephen; Bland, Andrew; Rekola, Leena; Haho, Päivi

2018-03-01

The purpose of this article is to introduce the concept of design-based research, its appropriateness in creating education-based models, and to describe the process of developing such a model. The model was designed as part of the Nurse Educator Simulation based learning project, funded by the EU's Lifelong Learning program (2013-1-DK1-LEO05-07053). The project partners were VIA University College, Denmark, the University of Huddersfield, UK and Metropolia University of Applied Sciences, Finland. As an outcome of the development process, "the NESTLED model for educating simulation facilitators" (NESTLED model) was generated. This article also illustrates five design principles that could be applied to other pedagogies. Copyright © 2018 Elsevier Ltd. All rights reserved.

Design Transformations for Rule-based Procedural Modeling

KAUST Repository

Lienhard, Stefan; Lau, Cheryl; Mü ller, Pascal; Wonka, Peter; Pauly, Mark

2017-01-01

We introduce design transformations for rule-based procedural models, e.g., for buildings and plants. Given two or more procedural designs, each specified by a grammar, a design transformation combines elements of the existing designs to generate new designs. We introduce two technical components to enable design transformations. First, we extend the concept of discrete rule switching to rule merging, leading to a very large shape space for combining procedural models. Second, we propose an algorithm to jointly derive two or more grammars, called grammar co-derivation. We demonstrate two applications of our work: we show that our framework leads to a larger variety of models than previous work, and we show fine-grained transformation sequences between two procedural models.

Design Transformations for Rule-based Procedural Modeling

KAUST Repository

Lienhard, Stefan

2017-05-24

We introduce design transformations for rule-based procedural models, e.g., for buildings and plants. Given two or more procedural designs, each specified by a grammar, a design transformation combines elements of the existing designs to generate new designs. We introduce two technical components to enable design transformations. First, we extend the concept of discrete rule switching to rule merging, leading to a very large shape space for combining procedural models. Second, we propose an algorithm to jointly derive two or more grammars, called grammar co-derivation. We demonstrate two applications of our work: we show that our framework leads to a larger variety of models than previous work, and we show fine-grained transformation sequences between two procedural models.

Mechatronic Systems Design Methods, Models, Concepts

CERN Document Server

Janschek, Klaus

2012-01-01

In this textbook, fundamental methods for model-based design of mechatronic systems are presented in a systematic, comprehensive form. The method framework presented here comprises domain-neutral methods for modeling and performance analysis: multi-domain modeling (energy/port/signal-based), simulation (ODE/DAE/hybrid systems), robust control methods, stochastic dynamic analysis, and quantitative evaluation of designs using system budgets. The model framework is composed of analytical dynamic models for important physical and technical domains of realization of mechatronic functions, such as multibody dynamics, digital information processing and electromechanical transducers. Building on the modeling concept of a technology-independent generic mechatronic transducer, concrete formulations for electrostatic, piezoelectric, electromagnetic, and electrodynamic transducers are presented. More than 50 fully worked out design examples clearly illustrate these methods and concepts and enable independent study of th...

Model reduction in integrated controls-structures design

Science.gov (United States)

Maghami, Peiman G.

1993-01-01

It is the objective of this paper to present a model reduction technique developed for the integrated controls-structures design of flexible structures. Integrated controls-structures design problems are typically posed as nonlinear mathematical programming problems, where the design variables consist of both structural and control parameters. In the solution process, both structural and control design variables are constantly changing; therefore, the dynamic characteristics of the structure are also changing. This presents a problem in obtaining a reduced-order model for active control design and analysis which will be valid for all design points within the design space. In other words, the frequency and number of the significant modes of the structure (modes that should be included) may vary considerably throughout the design process. This is also true as the locations and/or masses of the sensors and actuators change. Moreover, since the number of design evaluations in the integrated design process could easily run into thousands, any feasible order-reduction method should not require model reduction analysis at every design iteration. In this paper a novel and efficient technique for model reduction in the integrated controls-structures design process, which addresses these issues, is presented.

Electromagnetic modeling in accelerator designs

International Nuclear Information System (INIS)

Cooper, R.K.; Chan, K.C.D.

1990-01-01

Through the years, electromagnetic modeling using computers has proved to be a cost-effective tool for accelerator designs. Traditionally, electromagnetic modeling of accelerators has been limited to resonator and magnet designs in two dimensions. In recent years with the availability of powerful computers, electromagnetic modeling of accelerators has advanced significantly. Through the above conferences, it is apparent that breakthroughs have been made during the last decade in two important areas: three-dimensional modeling and time-domain simulation. Success in both these areas have been made possible by the increasing size and speed of computers. In this paper, the advances in these two areas will be described

Designers workbench: toward real-time immersive modeling

Science.gov (United States)

Kuester, Falko; Duchaineau, Mark A.; Hamann, Bernd; Joy, Kenneth I.; Ma, Kwan-Liu

2000-05-01

This paper introduces the Designers Workbench, a semi- immersive virtual environment for two-handed modeling, sculpting and analysis tasks. The paper outlines the fundamental tools, design metaphors and hardware components required for an intuitive real-time modeling system. As companies focus on streamlining productivity to cope with global competition, the migration to computer-aided design (CAD), computer-aided manufacturing, and computer-aided engineering systems has established a new backbone of modern industrial product development. However, traditionally a product design frequently originates form a clay model that, after digitization, forms the basis for the numerical description of CAD primitives. The Designers Workbench aims at closing this technology or 'digital gap' experienced by design and CAD engineers by transforming the classical design paradigm into its fully integrate digital and virtual analog allowing collaborative development in a semi- immersive virtual environment. This project emphasizes two key components form the classical product design cycle: freeform modeling and analysis. In the freedom modeling stage, content creation in the form of two-handed sculpting of arbitrary objects using polygonal, volumetric or mathematically defined primitives is emphasized, whereas the analysis component provides the tools required for pre- and post-processing steps for finite element analysis tasks applied to the created models.

A Robust Design Applicability Model

DEFF Research Database (Denmark)

Ebro, Martin; Lars, Krogstie; Howard, Thomas J.

2015-01-01

to be applicable in organisations assigning a high importance to one or more factors that are known to be impacted by RD, while also experiencing a high level of occurrence of this factor. The RDAM supplements existing maturity models and metrics to provide a comprehensive set of data to support management......This paper introduces a model for assessing the applicability of Robust Design (RD) in a project or organisation. The intention of the Robust Design Applicability Model (RDAM) is to provide support for decisions by engineering management considering the relevant level of RD activities...

Threat modeling designing for security

CERN Document Server

Shostack, Adam

2014-01-01

Adam Shostack is responsible for security development lifecycle threat modeling at Microsoft and is one of a handful of threat modeling experts in the world. Now, he is sharing his considerable expertise into this unique book. With pages of specific actionable advice, he details how to build better security into the design of systems, software, or services from the outset. You'll explore various threat modeling approaches, find out how to test your designs against threats, and learn effective ways to address threats that have been validated at Microsoft and other top companies. Systems secur

Perceiving design as modelling: A cybernetic systems perspective

DEFF Research Database (Denmark)

Maier, Anja; Wynn, David C.; Howard, Thomas J.

2014-01-01

The creation and use of models is central to engineering design, to the extent that designing might be perceived as a propagation from model to model and modelling may be described as the language of the designer (the terms product model and artefact model are used synonymously throughout this ch...

Designing a Sustainable Future with Mental Models

OpenAIRE

Bernotat, Anke; Bertling, Jürgen; English, Christiane; Schanz, Judith

2017-01-01

Inspired by the question of the Club of Rome as to Design could help to translate the ubiquitous knowledge on sustainability into daily practise and Peter Senge's belief on mental models as a limiting factor to implementation of systemic insight (Senge 2006), we explored working with mental models as a sustainable design tool. We propose a definition for design uses. At the 7th Sustainable Summer School we collected general unsustainable mental models and "designed" sustainable ones. These me...

Verilog HDL digital design and modeling

CERN Document Server

Cavanagh, Joseph

2007-01-01

PREFACE INTRODUCTION History of HDL Verilog HDL IEEE Standard Features Assertion Levels OVERVIEW Design Methodologies Modulo-16 Synchronous Counter Four-Bit Ripple Adder Modules and Ports Designing a Test Bench for Simulation Construct Definitions Introduction to Dataflow Modeling Two-Input Exclusive-OR Gate Four 2-Input AND Gates With Delay Introduction to Behavioral Modeling Three-Input OR Gate Four-Bit Adder Modulo-16 Synchronous Counter Introduction to Structural Modeling Sum-of-Products Implementation Full Adder Four-Bit Ripple Adder Introduction to Mixed-Design Modeling Full Adder Problems LANGUAGE ELEMENTS Comments Identifiers Keywords Bidirectional Gates Charge Storage Strengths CMOS Gates Combinational Logic Gates Continuous Assignment Data Types Module Declaration MOS Switches Multiple-Way Branching Named Ev...

Optimizing Intermodal Train Schedules with a Design Balanced Network Design Model

DEFF Research Database (Denmark)

Pedersen, Michael Berliner; Crainic, Teodor Gabriel

We present a modeling approach for optimizing intermodal trains schedules based on an infrastructure divided into time-dependent train paths. The formulation can be generalized to a capacitated multi commodity network design model with additional design balance constraints. We present a Tabu Search...

On Design Mining: Coevolution and Surrogate Models.

Science.gov (United States)

Preen, Richard J; Bull, Larry

2017-01-01

Design mining is the use of computational intelligence techniques to iteratively search and model the attribute space of physical objects evaluated directly through rapid prototyping to meet given objectives. It enables the exploitation of novel materials and processes without formal models or complex simulation. In this article, we focus upon the coevolutionary nature of the design process when it is decomposed into concurrent sub-design-threads due to the overall complexity of the task. Using an abstract, tunable model of coevolution, we consider strategies to sample subthread designs for whole-system testing and how best to construct and use surrogate models within the coevolutionary scenario. Drawing on our findings, we then describe the effective design of an array of six heterogeneous vertical-axis wind turbines.

Information-Processing Models and Curriculum Design

Science.gov (United States)

Calfee, Robert C.

1970-01-01

"This paper consists of three sections--(a) the relation of theoretical analyses of learning to curriculum design, (b) the role of information-processing models in analyses of learning processes, and (c) selected examples of the application of information-processing models to curriculum design problems." (Author)

Conceptual Models Core to Good Design

CERN Document Server

Johnson, Jeff

2011-01-01

People make use of software applications in their activities, applying them as tools in carrying out tasks. That this use should be good for people--easy, effective, efficient, and enjoyable--is a principal goal of design. In this book, we present the notion of Conceptual Models, and argue that Conceptual Models are core to achieving good design. From years of helping companies create software applications, we have come to believe that building applications without Conceptual Models is just asking for designs that will be confusing and difficult to learn, remember, and use. We show how Concept

Modeling Languages Refine Vehicle Design

Science.gov (United States)

2009-01-01

Cincinnati, Ohio s TechnoSoft Inc. is a leading provider of object-oriented modeling and simulation technology used for commercial and defense applications. With funding from Small Business Innovation Research (SBIR) contracts issued by Langley Research Center, the company continued development on its adaptive modeling language, or AML, originally created for the U.S. Air Force. TechnoSoft then created what is now known as its Integrated Design and Engineering Analysis Environment, or IDEA, which can be used to design a variety of vehicles and machinery. IDEA's customers include clients in green industries, such as designers for power plant exhaust filtration systems and wind turbines.

Trading Robustness Requirements in Mars Entry Trajectory Design

Science.gov (United States)

Lafleur, Jarret M.

2009-01-01

One of the most important metrics characterizing an atmospheric entry trajectory in preliminary design is the size of its predicted landing ellipse. Often, requirements for this ellipse are set early in design and significantly influence both the expected scientific return from a particular mission and the cost of development. Requirements typically specify a certain probability level (6-level) for the prescribed ellipse, and frequently this latter requirement is taken at 36. However, searches for the justification of 36 as a robustness requirement suggest it is an empirical rule of thumb borrowed from non-aerospace fields. This paper presents an investigation into the sensitivity of trajectory performance to varying robustness (6-level) requirements. The treatment of robustness as a distinct objective is discussed, and an analysis framework is presented involving the manipulation of design variables to effect trades between performance and robustness objectives. The scenario for which this method is illustrated is the ballistic entry of an MSL-class Mars entry vehicle. Here, the design variable is entry flight path angle, and objectives are parachute deploy altitude performance and error ellipse robustness. Resulting plots show the sensitivities between these objectives and trends in the entry flight path angles required to design to these objectives. Relevance to the trajectory designer is discussed, as are potential steps for further development and use of this type of analysis.

Compact MOSFET models for VLSI design

CERN Document Server

Bhattacharyya, A B

2009-01-01

Practicing designers, students, and educators in the semiconductor field face an ever expanding portfolio of MOSFET models. In Compact MOSFET Models for VLSI Design , A.B. Bhattacharyya presents a unified perspective on the topic, allowing the practitioner to view and interpret device phenomena concurrently using different modeling strategies. Readers will learn to link device physics with model parameters, helping to close the gap between device understanding and its use for optimal circuit performance. Bhattacharyya also lays bare the core physical concepts that will drive the future of VLSI.

Prototype design based on NX subdivision modeling application

Science.gov (United States)

Zhan, Xianghui; Li, Xiaoda

2018-04-01

Prototype design is an important part of the product design, through a quick and easy way to draw a three-dimensional product prototype. Combined with the actual production, the prototype could be modified several times, resulting in a highly efficient and reasonable design before the formal design. Subdivision modeling is a common method of modeling product prototypes. Through Subdivision modeling, people can in a short time with a simple operation to get the product prototype of the three-dimensional model. This paper discusses the operation method of Subdivision modeling for geometry. Take a vacuum cleaner as an example, the NX Subdivision modeling functions are applied. Finally, the development of Subdivision modeling is forecasted.

Integrating Design Decision Management with Model-based Software Development

DEFF Research Database (Denmark)

Könemann, Patrick

Design decisions are continuously made during the development of software systems and are important artifacts for design documentation. Dedicated decision management systems are often used to capture such design knowledge. Most such systems are, however, separated from the design artifacts...... of the system. In model-based software development, where design models are used to develop a software system, outcomes of many design decisions have big impact on design models. The realization of design decisions is often manual and tedious work on design models. Moreover, keeping design models consistent......, or by ignoring the causes. This substitutes manual reviews to some extent. The concepts, implemented in a tool, have been validated with design patterns, refactorings, and domain level tests that comprise a replay of a real project. This proves the applicability of the solution to realistic examples...

Consequence Based Design. An approach for integrating computational collaborative models (Integrated Dynamic Models) in the building design phase

DEFF Research Database (Denmark)

Negendahl, Kristoffer

relies on various advancements in the area of integrated dynamic models. It also relies on the application and test of the approach in practice to evaluate the Consequence based design and the use of integrated dynamic models. As a result, the Consequence based design approach has been applied in five...... and define new ways to implement integrated dynamic models for the following project. In parallel, seven different developments of new methods, tools and algorithms have been performed to support the application of the approach. The developments concern: Decision diagrams – to clarify goals and the ability...... affect the design process and collaboration between building designers and simulationists. Within the limits of applying the approach of Consequence based design to five case studies, followed by documentation based on interviews, surveys and project related documentations derived from internal reports...

Conceptual design interpretations, mindset and models

CERN Document Server

Andreasen, Mogens Myrup; Cash, Philip

2015-01-01

Maximising reader insights into the theory, models, methods and fundamental reasoning of design, this book addresses design activities in industrial settings, as well as the actors involved. This approach offers readers a new understanding of design activities and related functions, properties and dispositions. Presenting a ‘design mindset’ that seeks to empower students, researchers, and practitioners alike, it features a strong focus on how designers create new concepts to be developed into products, and how they generate new business and satisfy human needs.   Employing a multi-faceted perspective, the book supplies the reader with a comprehensive worldview of design in the form of a proposed model that will empower their activities as student, researcher or practitioner. We draw the reader into the core role of design conceptualisation for society, for the development of industry, for users and buyers of products, and for citizens in relation to public systems. The book also features original con...

ARCHITECTURAL FORM CREATION IN THE DESIGN STUDIO: PHYSICAL MODELING AS AN EFFECTIVE DESIGN TOOL

Directory of Open Access Journals (Sweden)

Wael Abdelhameed

2011-11-01

Full Text Available This research paper attempts to shed more light on an area of the design studio, which concerns with the use of physical modeling as a design medium in architectural form creation. An experiment has been carried out during an architectural design studio in order to not only investigate physical modeling as a tool of form creation but also improve visual design thinking that students employ while using this manual tool. To achieve the research objective, a method was proposed and applied to track form creation processes, based upon three types of operation, namely: sketching transformations, divergent physical-modeling transformations, and convergent physical-modeling transformations. The method helps record the innovative transitions of form during conceptual designing in a simple way. Investigating form creation processes and activities associated with visual design thinking enables the research to conclude to general results of the role of physical modeling in the conceptual phase of designing, and to specific results of the methods used in this architectural design studio experiment.

TP-model transformation-based-control design frameworks

CERN Document Server

Baranyi, Péter

2016-01-01

This book covers new aspects and frameworks of control, design, and optimization based on the TP model transformation and its various extensions. The author outlines the three main steps of polytopic and LMI based control design: 1) development of the qLPV state-space model, 2) generation of the polytopic model; and 3) application of LMI to derive controller and observer. He goes on to describe why literature has extensively studied LMI design, but has not focused much on the second step, in part because the generation and manipulation of the polytopic form was not tractable in many cases. The author then shows how the TP model transformation facilitates this second step and hence reveals new directions, leading to powerful design procedures and the formulation of new questions. The chapters of this book, and the complex dynamical control tasks which they cover, are organized so as to present and analyze the beneficial aspect of the family of approaches (control, design, and optimization). Additionally, the b...

AN INSTRUCTIONAL DESIGN MODEL FOR BLENDED HIGHER EDUCATION

Directory of Open Access Journals (Sweden)

George Hack

2016-07-01

Full Text Available Instructional design models that are used by many higher education institutions to guide course design are insufficient for the unique opportunities of blended learning. Many established models are not practical tools for college faculty to use independently in the design of courses. Models like A.D.D.I.E., use a linear approach that can translate more easily into practical stages of course design, yet are historically rooted in the rapid prototyping of educational technologies or for designing military training and are inadequate for the complex demands of higher education, where learning outcomes are geared toward higher order thinking, scientific/clinical reasoning, and a syntheses of ideas into new knowledge. Presented here is an instructional design model that strategically incorporates the nuances of higher education, yet is practically framed to assist faculty with design challenges.

Using interactive model simulations in co-design : An experiment in urban design

NARCIS (Netherlands)

Steen, M.G.D.; Arendsen, J.; Cremers, A.H.M.; Vries, A. de; Jong, J.M.G. de; Koning, N.M. de

2013-01-01

This paper presents an experiment in which people performed a co-design task in urban design, using a multi-user touch table application with or without interactive model simulations. We hypothesised that using the interactive model simulations would improve communication and co-operation between

Modeling Adaptive Behavior for Systems Design

DEFF Research Database (Denmark)

Rasmussen, Jens

1994-01-01

Field studies in modern work systems and analysis of recent major accidents have pointed to a need for better models of the adaptive behavior of individuals and organizations operating in a dynamic and highly competitive environment. The paper presents a discussion of some key characteristics.......) The basic difference between the models of system functions used in engineering and design and those evolving from basic research within the various academic disciplines and finally 3.) The models and methods required for closed-loop, feedback system design....

Level Design as Model Transformation

NARCIS (Netherlands)

Dormans, Joris

2011-01-01

This paper frames the process of designing a level in a game as a series of model transformations. The transformations correspond to the application of particular design principles, such as the use of locks and keys to transform a linear mission into a branching space. It shows that by using rewrite

Flow Studies of Decelerators at Supersonic Speeds

Science.gov (United States)

1959-01-01

Wind tunnel tests recorded the effect of decelerators on flow at various supersonic speeds. Rigid parachute models were tested for the effects of porosity, shroud length, and number of shrouds. Flexible model parachutes were tested for effects of porosity and conical-shaped canopy. Ribbon dive brakes on a missile-shaped body were tested for effect of tension cable type and ribbon flare type. The final test involved a plastic sphere on riser lines.

Embracing model-based designs for dose-finding trials.

Science.gov (United States)

Love, Sharon B; Brown, Sarah; Weir, Christopher J; Harbron, Chris; Yap, Christina; Gaschler-Markefski, Birgit; Matcham, James; Caffrey, Louise; McKevitt, Christopher; Clive, Sally; Craddock, Charlie; Spicer, James; Cornelius, Victoria

2017-07-25

Dose-finding trials are essential to drug development as they establish recommended doses for later-phase testing. We aim to motivate wider use of model-based designs for dose finding, such as the continual reassessment method (CRM). We carried out a literature review of dose-finding designs and conducted a survey to identify perceived barriers to their implementation. We describe the benefits of model-based designs (flexibility, superior operating characteristics, extended scope), their current uptake, and existing resources. The most prominent barriers to implementation of a model-based design were lack of suitable training, chief investigators' preference for algorithm-based designs (e.g., 3+3), and limited resources for study design before funding. We use a real-world example to illustrate how these barriers can be overcome. There is overwhelming evidence for the benefits of CRM. Many leading pharmaceutical companies routinely implement model-based designs. Our analysis identified barriers for academic statisticians and clinical academics in mirroring the progress industry has made in trial design. Unified support from funders, regulators, and journal editors could result in more accurate doses for later-phase testing, and increase the efficiency and success of clinical drug development. We give recommendations for increasing the uptake of model-based designs for dose-finding trials in academia.

The Role(s) of Process Models in Design Practice

DEFF Research Database (Denmark)

Iversen, Søren; Jensen, Mads Kunø Nyegaard; Vistisen, Peter

2018-01-01

This paper investigates how design process models are implemented and used in design-driven organisations. The archetypical theoretical framing of process models, describe their primary role as guiding the design process, and assign roles and deliverables throughout the process. We hypothesise...... that the process models also take more communicative roles in practice, both in terms of creating an internal design rationale, as well as demystifying the black box of design thinking to external stakeholders. We investigate this hypothesis through an interview study of four major danish design......-driven organisations, and analyse the different roles their archetypical process models take in their organisations. The main contribution is the identification of three, often overlapping roles, which design process models showed to assume in design-driven organisations: process guidance, adding transparency...

Modeling Organizational Design - Applying A Formalism Model From Theoretical Physics

Directory of Open Access Journals (Sweden)

Robert Fabac

2008-06-01

Full Text Available Modern organizations are exposed to diverse external environment influences. Currently accepted concepts of organizational design take into account structure, its interaction with strategy, processes, people, etc. Organization design and planning aims to align this key organizational design variables. At the higher conceptual level, however, completely satisfactory formulation for this alignment doesn’t exist. We develop an approach originating from the application of concepts of theoretical physics to social systems. Under this approach, the allocation of organizational resources is analyzed in terms of social entropy, social free energy and social temperature. This allows us to formalize the dynamic relationship between organizational design variables. In this paper we relate this model to Galbraith's Star Model and we also suggest improvements in the procedure of the complex analytical method in organizational design.

Persuasive Game Design : A model and its definitions

NARCIS (Netherlands)

Visch, V.T.; Vegt, N.J.H.; Anderiesen, H.; Van der Kooij, K.

2013-01-01

The following position paper proposes a general theoretical model for persuasive game design. This model combines existing theories on persuasive technology, serious gaming, and gamification. The model is based on user experience, gamification design, and transfer effects.

Design and Operationalization of Technological Business Models

Directory of Open Access Journals (Sweden)

Adam Jabłoński

2015-01-01

Full Text Available The mechanisms of the network paradigm increasingly affecting the operation of companies form a new dimension of strategic management today. This applies also to the look at the design and operationalization of business models. Business models that become a source of competitive advantage in the market should have such a configuration that will provide the company with the capability to develop and grow in value. Innovation in particular determines this capability, which is the basis for the ability to create technologically new products and services. An interesting issue, not fully examined yet, is defining the principles of the design and operationalization of such business models in which technology determines their efficiency and effectiveness. These models may be technological business models. The aim of this paper is to discuss the important areas related to the design and operationalization of technological business models in the network environment and to present conclusions that are the basis for further research in this area. The author argues that in today’s, increasingly virtual reality effective and efficient tools for generating new value proposition for customers is the skillful design and use of technological business models developed by companies’ participation in the network environment. It is materialized in the form of achieving superior business results by the company.

Designing user models in a virtual cave environment

Energy Technology Data Exchange (ETDEWEB)

Brown-VanHoozer, S. [Argonne National Lab., Idaho Falls, ID (United States); Hudson, R. [Argonne National Lab., IL (United States); Gokhale, N. [Madge Networks, San Jose, CA (United States)

1995-12-31

In this paper, the results of a first study into the use of virtual reality for human factor studies and design of simple and complex models of control systems, components, and processes are described. The objective was to design a model in a virtual environment that would reflect more characteristics of the user`s mental model of a system and fewer of the designer`s. The technology of a CAVE{trademark} virtual environment and the methodology of Neuro Linguistic Programming were employed in this study.

Computer-based Creativity Enhanced Conceptual Design Model for Non-routine Design of Mechanical Systems

Institute of Scientific and Technical Information of China (English)

LI Yutong; WANG Yuxin; DUFFY Alex H B

2014-01-01

Computer-based conceptual design for routine design has made great strides, yet non-routine design has not been given due attention, and it is still poorly automated. Considering that the function-behavior-structure(FBS) model is widely used for modeling the conceptual design process, a computer-based creativity enhanced conceptual design model(CECD) for non-routine design of mechanical systems is presented. In the model, the leaf functions in the FBS model are decomposed into and represented with fine-grain basic operation actions(BOA), and the corresponding BOA set in the function domain is then constructed. Choosing building blocks from the database, and expressing their multiple functions with BOAs, the BOA set in the structure domain is formed. Through rule-based dynamic partition of the BOA set in the function domain, many variants of regenerated functional schemes are generated. For enhancing the capability to introduce new design variables into the conceptual design process, and dig out more innovative physical structure schemes, the indirect function-structure matching strategy based on reconstructing the combined structure schemes is adopted. By adjusting the tightness of the partition rules and the granularity of the divided BOA subsets, and making full use of the main function and secondary functions of each basic structure in the process of reconstructing of the physical structures, new design variables and variants are introduced into the physical structure scheme reconstructing process, and a great number of simpler physical structure schemes to accomplish the overall function organically are figured out. The creativity enhanced conceptual design model presented has a dominant capability in introducing new deign variables in function domain and digging out simpler physical structures to accomplish the overall function, therefore it can be utilized to solve non-routine conceptual design problem.

Computer-based creativity enhanced conceptual design model for non-routine design of mechanical systems

Science.gov (United States)

Li, Yutong; Wang, Yuxin; Duffy, Alex H. B.

2014-11-01

Computer-based conceptual design for routine design has made great strides, yet non-routine design has not been given due attention, and it is still poorly automated. Considering that the function-behavior-structure(FBS) model is widely used for modeling the conceptual design process, a computer-based creativity enhanced conceptual design model(CECD) for non-routine design of mechanical systems is presented. In the model, the leaf functions in the FBS model are decomposed into and represented with fine-grain basic operation actions(BOA), and the corresponding BOA set in the function domain is then constructed. Choosing building blocks from the database, and expressing their multiple functions with BOAs, the BOA set in the structure domain is formed. Through rule-based dynamic partition of the BOA set in the function domain, many variants of regenerated functional schemes are generated. For enhancing the capability to introduce new design variables into the conceptual design process, and dig out more innovative physical structure schemes, the indirect function-structure matching strategy based on reconstructing the combined structure schemes is adopted. By adjusting the tightness of the partition rules and the granularity of the divided BOA subsets, and making full use of the main function and secondary functions of each basic structure in the process of reconstructing of the physical structures, new design variables and variants are introduced into the physical structure scheme reconstructing process, and a great number of simpler physical structure schemes to accomplish the overall function organically are figured out. The creativity enhanced conceptual design model presented has a dominant capability in introducing new deign variables in function domain and digging out simpler physical structures to accomplish the overall function, therefore it can be utilized to solve non-routine conceptual design problem.

Network Design Models for Container Shipping

DEFF Research Database (Denmark)

Reinhardt, Line Blander; Kallehauge, Brian; Nielsen, Anders Nørrelund

This paper presents a study of the network design problem in container shipping. The paper combines the network design and fleet assignment problem into a mixed integer linear programming model minimizing the overall cost. The major contributions of this paper is that the time of a vessel route...... is included in the calculation of the capacity and that a inhomogeneous fleet is modeled. The model also includes the cost of transshipment which is one of the major cost for the shipping companies. The concept of pseudo simple routes is introduced to expand the set of feasible routes. The linearization...

Designer Modeling for Personalized Game Content Creation Tools

DEFF Research Database (Denmark)

Liapis, Antonios; Yannakakis, Georgios N.; Togelius, Julian

2013-01-01

preferences, goals and processes from their interaction with a computer-aided design tool, and suggests methods and domains within game development where such a model can be applied. We describe how designer modeling could be integrated with current work on automated and mixed-initiative content creation......With the growing use of automated content creation and computer-aided design tools in game development, there is potential for enhancing the design process through personalized interactions between the software and the game developer. This paper proposes designer modeling for capturing the designer’s......, and envision future directions which focus on personalizing the processes to a designer’s particular wishes....

Robust Bayesian Experimental Design for Conceptual Model Discrimination

Science.gov (United States)

Pham, H. V.; Tsai, F. T. C.

2015-12-01

A robust Bayesian optimal experimental design under uncertainty is presented to provide firm information for model discrimination, given the least number of pumping wells and observation wells. Firm information is the maximum information of a system can be guaranteed from an experimental design. The design is based on the Box-Hill expected entropy decrease (EED) before and after the experiment design and the Bayesian model averaging (BMA) framework. A max-min programming is introduced to choose the robust design that maximizes the minimal Box-Hill EED subject to that the highest expected posterior model probability satisfies a desired probability threshold. The EED is calculated by the Gauss-Hermite quadrature. The BMA method is used to predict future observations and to quantify future observation uncertainty arising from conceptual and parametric uncertainties in calculating EED. Monte Carlo approach is adopted to quantify the uncertainty in the posterior model probabilities. The optimal experimental design is tested by a synthetic 5-layer anisotropic confined aquifer. Nine conceptual groundwater models are constructed due to uncertain geological architecture and boundary condition. High-performance computing is used to enumerate all possible design solutions in order to identify the most plausible groundwater model. Results highlight the impacts of scedasticity in future observation data as well as uncertainty sources on potential pumping and observation locations.

Model predictive controller design of hydrocracker reactors

OpenAIRE

GÖKÇE, Dila

2011-01-01

This study summarizes the design of a Model Predictive Controller (MPC) in Tüpraş, İzmit Refinery Hydrocracker Unit Reactors. Hydrocracking process, in which heavy vacuum gasoil is converted into lighter and valuable products at high temperature and pressure is described briefly. Controller design description, identification and modeling studies are examined and the model variables are presented. WABT (Weighted Average Bed Temperature) equalization and conversion increase are simulate...

Modeling and design techniques for RF power amplifiers

CERN Document Server

Raghavan, Arvind; Laskar, Joy

2008-01-01

The book covers RF power amplifier design, from device and modeling considerations to advanced circuit design architectures and techniques. It focuses on recent developments and advanced topics in this area, including numerous practical designs to back the theoretical considerations. It presents the challenges in designing power amplifiers in silicon and helps the reader improve the efficiency of linear power amplifiers, and design more accurate compact device models, with faster extraction routines, to create cost effective and reliable circuits.

Using the Continuum of Design Modelling Techniques to Aid the Development of CAD Modeling Skills in First Year Industrial Design Students

Science.gov (United States)

Storer, I. J.; Campbell, R. I.

2012-01-01

Industrial Designers need to understand and command a number of modelling techniques to communicate their ideas to themselves and others. Verbal explanations, sketches, engineering drawings, computer aided design (CAD) models and physical prototypes are the most commonly used communication techniques. Within design, unlike some disciplines,…

Jovian Plasma Modeling for Mission Design

Science.gov (United States)

Garrett, Henry B.; Kim, Wousik; Belland, Brent; Evans, Robin

2015-01-01

The purpose of this report is to address uncertainties in the plasma models at Jupiter responsible for surface charging and to update the jovian plasma models using the most recent data available. The updated plasma environment models were then used to evaluate two proposed Europa mission designs for spacecraft charging effects using the Nascap-2k code. The original Divine/Garrett jovian plasma model (or "DG1", T. N. Divine and H. B. Garrett, "Charged particle distributions in Jupiter's magnetosphere," J. Geophys. Res., vol. 88, pp. 6889-6903,1983) has not been updated in 30 years, and there are known errors in the model. As an example, the cold ion plasma temperatures between approx.5 and 10 Jupiter radii (Rj) were found by the experimenters who originally published the data to have been underestimated by approx.2 shortly after publication of the original DG1 model. As knowledge of the plasma environment is critical to any evaluation of the surface charging at Jupiter, the original DG1 model needed to be updated to correct for this and other changes in our interpretation of the data so that charging levels could beproperly estimated using the Nascap-2k charging code. As an additional task, the Nascap-2k spacecraft charging tool has been adapted to incorporate the so-called Kappa plasma distribution function--an important component of the plasma model necessary to compute the particle fluxes between approx.5 keV and 100 keV (at the outset of this study,Nascap-2k did not directly incorporate this common representation of the plasma thus limiting the accuracy of our charging estimates). The updating of the DG1 model and its integration into the Nascap-2k design tool means that charging concerns can now be more efficiently evaluated and mitigated. (We note that, given the subsequent decision by the Europa project to utilize solar arrays for its baseline design, surface charging effects have becomeeven more of an issue for its mission design). The modifications and

Chaos Generation Managed Through Design Thinking: a Task Model for the Design Professional

DEFF Research Database (Denmark)

Knudsen, Christina; Møllenbach, Emilie

2016-01-01

The task model presented here is a working vision for the design professional redirecting focus from the application of predefined project structures to a process of complex evaluation. The task model is developed through a hermeneutic analysis of the discourse applied by design professionals...

Design Concept Evaluation Using System Throughput Model

International Nuclear Information System (INIS)

Sequeira, G.; Nutt, W. M.

2004-01-01

The U.S. Department of Energy (DOE) Office of Civilian Radioactive Waste Management (OCRWM) is currently developing the technical bases to support the submittal of a license application for construction of a geologic repository at Yucca Mountain, Nevada to the U.S. Nuclear Regulatory Commission. The Office of Repository Development (ORD) is responsible for developing the design of the proposed repository surface facilities for the handling of spent nuclear fuel and high level nuclear waste. Preliminary design activities are underway to sufficiently develop the repository surface facilities design for inclusion in the license application. The design continues to evolve to meet mission needs and to satisfy both regulatory and program requirements. A system engineering approach is being used in the design process since the proposed repository facilities are dynamically linked by a series of sub-systems and complex operations. In addition, the proposed repository facility is a major system element of the overall waste management process being developed by the OCRWM. Such an approach includes iterative probabilistic dynamic simulation as an integral part of the design evolution process. A dynamic simulation tool helps to determine if: (1) the mission and design requirements are complete, robust, and well integrated; (2) the design solutions under development meet the design requirements and mission goals; (3) opportunities exist where the system can be improved and/or optimized; and (4) proposed changes to the mission, and design requirements have a positive or negative impact on overall system performance and if design changes may be necessary to satisfy these changes. This paper will discuss the type of simulation employed to model the waste handling operations. It will then discuss the process being used to develop the Yucca Mountain surface facilities model. The latest simulation model and the results of the simulation and how the data were used in the design

Robust input design for nonlinear dynamic modeling of AUV.

Science.gov (United States)

Nouri, Nowrouz Mohammad; Valadi, Mehrdad

2017-09-01

Input design has a dominant role in developing the dynamic model of autonomous underwater vehicles (AUVs) through system identification. Optimal input design is the process of generating informative inputs that can be used to generate the good quality dynamic model of AUVs. In a problem with optimal input design, the desired input signal depends on the unknown system which is intended to be identified. In this paper, the input design approach which is robust to uncertainties in model parameters is used. The Bayesian robust design strategy is applied to design input signals for dynamic modeling of AUVs. The employed approach can design multiple inputs and apply constraints on an AUV system's inputs and outputs. Particle swarm optimization (PSO) is employed to solve the constraint robust optimization problem. The presented algorithm is used for designing the input signals for an AUV, and the estimate obtained by robust input design is compared with that of the optimal input design. According to the results, proposed input design can satisfy both robustness of constraints and optimality. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

A reference model for model-based design of critical infrastructure protection systems

Science.gov (United States)

Shin, Young Don; Park, Cheol Young; Lee, Jae-Chon

2015-05-01

Today's war field environment is getting versatile as the activities of unconventional wars such as terrorist attacks and cyber-attacks have noticeably increased lately. The damage caused by such unconventional wars has also turned out to be serious particularly if targets are critical infrastructures that are constructed in support of banking and finance, transportation, power, information and communication, government, and so on. The critical infrastructures are usually interconnected to each other and thus are very vulnerable to attack. As such, to ensure the security of critical infrastructures is very important and thus the concept of critical infrastructure protection (CIP) has come. The program to realize the CIP at national level becomes the form of statute in each country. On the other hand, it is also needed to protect each individual critical infrastructure. The objective of this paper is to study on an effort to do so, which can be called the CIP system (CIPS). There could be a variety of ways to design CIPS's. Instead of considering the design of each individual CIPS, a reference model-based approach is taken in this paper. The reference model represents the design of all the CIPS's that have many design elements in common. In addition, the development of the reference model is also carried out using a variety of model diagrams. The modeling language used therein is the systems modeling language (SysML), which was developed and is managed by Object Management Group (OMG) and a de facto standard. Using SysML, the structure and operational concept of the reference model are designed to fulfil the goal of CIPS's, resulting in the block definition and activity diagrams. As a case study, the operational scenario of the nuclear power plant while being attacked by terrorists is studied using the reference model. The effectiveness of the results is also analyzed using multiple analysis models. It is thus expected that the approach taken here has some merits

Analytical models for low-power rectenna design

NARCIS (Netherlands)

Akkermans, J.A.G.; Beurden, van M.C.; Doodeman, G.J.N.; Visser, H.J.

2005-01-01

The design of a low-cost rectenna for low-power applications is presented. The rectenna is designed with the use of analytical models and closed-form analytical expressions. This allows for a fast design of the rectenna system. To acquire a small-area rectenna, a layered design is proposed.

Journal of Modeling, Design and Management of Engineering ...

African Journals Online (AJOL)

Journal of Modeling, Design and Management of Engineering Systems. ... Journal Home > Vol 5, No 1 (2007) ... or mathematical modeling, computing, simulation, design and/or operations research tools for solving engineering problems.

Modelling Approach In Islamic Architectural Designs

Directory of Open Access Journals (Sweden)

Suhaimi Salleh

2014-06-01

Full Text Available Architectural designs contribute as one of the main factors that should be considered in minimizing negative impacts in planning and structural development in buildings such as in mosques. In this paper, the ergonomics perspective is revisited which hence focuses on the conditional factors involving organisational, psychological, social and population as a whole. This paper tries to highlight the functional and architectural integration with ecstatic elements in the form of decorative and ornamental outlay as well as incorporating the building structure such as wall, domes and gates. This paper further focuses the mathematical aspects of the architectural designs such as polar equations and the golden ratio. These designs are modelled into mathematical equations of various forms, while the golden ratio in mosque is verified using two techniques namely, the geometric construction and the numerical method. The exemplary designs are taken from theSabah Bandaraya Mosque in Likas, Kota Kinabalu and the Sarawak State Mosque in Kuching,while the Universiti Malaysia Sabah Mosque is used for the Golden Ratio. Results show thatIslamic architectural buildings and designs have long had mathematical concepts and techniques underlying its foundation, hence, a modelling approach is needed to rejuvenate these Islamic designs.

Model-based design languages: A case study

OpenAIRE

Cibrario Bertolotti, Ivan; Hu, Tingting; Navet, Nicolas

2017-01-01

Fast-paced innovation in the embedded systems domain puts an ever increasing pressure on effective software development methods, leading to the growing popularity of Model-Based Design (MBD). In this context, a proper choice of modeling languages and related tools - depending on design goals and problem qualities - is crucial to make the most of MBD benefits. In this paper, a comparison between two dissimilar approaches to modeling is carried out, with the goal of highlighting their relative ...

Modeling, simulation, and design of SAW grating filters

Science.gov (United States)

Schwelb, Otto; Adler, E. L.; Slaboszewicz, J. K.

1990-05-01

A systematic procedure for modeling, simulating, and designing SAW (surface acoustic wave) grating filters, taking losses into account, is described. Grating structures and IDTs (interdigital transducers) coupling to SAWs are defined by cascadable transmission-matrix building blocks. Driving point and transfer characteristics (immittances) of complex architectures consisting of gratings, transducers, and coupling networks are obtained by chain-multiplying building-block matrices. This modular approach to resonator filter analysis and design combines the elements of lossy filter synthesis with the transmission-matrix description of SAW components. A multipole filter design procedure based on a lumped-element-model approximation of one-pole two-port resonator building blocks is given and the range of validity of this model examined. The software for simulating the performance of SAW grating devices based on this matrix approach is described, and its performance, when linked to the design procedure to form a CAD/CAA (computer-aided design and analysis) multiple-filter design package, is illustrated with a resonator filter design example.

A business model design framework for viability : a business ecosystem approach

NARCIS (Netherlands)

D'Souza, Austin; Velthuijsen, Hugo; Wortmann, J.C.; Huitema, George

2015-01-01

Purpose: To facilitate the design of viable business models by proposing a novel business model design framework for viability. Design: A design science research method is adopted to develop a business model design framework for viability. The business model design framework for viability is

Research on an innovative design model

Science.gov (United States)

Fu, Y.; Fang, H.

2018-03-01

The design methods of furniture are different from east to west; it has been the hotspot of the scholars. However, in terms of the theory of modern design innovation, neither the early creation theory, the modern design theory, nor the widely applied TRIZ theory can fully fit the modern furniture design innovation, so it is urgent to study the modern furniture design theory. This paper is based on the idea of TRIZ theory, using lots of literatures as data, and uses the method of statistical stratification to analyze and sort out the research of modern sitting equipment, and finally put forward the modern furniture design model, which provides new ideas and perspectives for the modern design of Chinese furniture.

A decision-making model for engineering designers

DEFF Research Database (Denmark)

Ahmed, S.; Hansen, Claus Thorp

2002-01-01

This paper describes research that combines the generic decision-making model of Hansen, together with design strategies employed by experienced engineering designers. The relationship between the six decision-making sub-activities and the eight design strategies are examined. By combining...

Modeling OPC complexity for design for manufacturability

Science.gov (United States)

Gupta, Puneet; Kahng, Andrew B.; Muddu, Swamy; Nakagawa, Sam; Park, Chul-Hong

2005-11-01

Increasing design complexity in sub-90nm designs results in increased mask complexity and cost. Resolution enhancement techniques (RET) such as assist feature addition, phase shifting (attenuated PSM) and aggressive optical proximity correction (OPC) help in preserving feature fidelity in silicon but increase mask complexity and cost. Data volume increase with rise in mask complexity is becoming prohibitive for manufacturing. Mask cost is determined by mask write time and mask inspection time, which are directly related to the complexity of features printed on the mask. Aggressive RET increase complexity by adding assist features and by modifying existing features. Passing design intent to OPC has been identified as a solution for reducing mask complexity and cost in several recent works. The goal of design-aware OPC is to relax OPC tolerances of layout features to minimize mask cost, without sacrificing parametric yield. To convey optimal OPC tolerances for manufacturing, design optimization should drive OPC tolerance optimization using models of mask cost for devices and wires. Design optimization should be aware of impact of OPC correction levels on mask cost and performance of the design. This work introduces mask cost characterization (MCC) that quantifies OPC complexity, measured in terms of fracture count of the mask, for different OPC tolerances. MCC with different OPC tolerances is a critical step in linking design and manufacturing. In this paper, we present a MCC methodology that provides models of fracture count of standard cells and wire patterns for use in design optimization. MCC cannot be performed by designers as they do not have access to foundry OPC recipes and RET tools. To build a fracture count model, we perform OPC and fracturing on a limited set of standard cells and wire configurations with all tolerance combinations. Separately, we identify the characteristics of the layout that impact fracture count. Based on the fracture count (FC) data

Design Developing of IC- Model Using VHDL

International Nuclear Information System (INIS)

Inzar-Anas

2005-01-01

In present, the electronic design required to become simple, small and flexible. The physical dimension of IC and number of pin can be significantly reduced while the flexibility and compatibility of IC was not change. Implementation of VHDL(VHSIC Hardware Description Language) seem as a great progress in the design of digital circuit. By using this language designing of model can be more simple, flexible and efficient. This paper was purposed to introduce VHDL and its features. Sample in modeling to illustrate the advantage of VHDL will also be described. (author)

Optimal designs for linear mixture models

NARCIS (Netherlands)

Mendieta, E.J.; Linssen, H.N.; Doornbos, R.

1975-01-01

In a recent paper Snee and Marquardt (1974) considered designs for linear mixture models, where the components are subject to individual lower and/or upper bounds. When the number of components is large their algorithm XVERT yields designs far too extensive for practical purposes. The purpose of

Engineering design of systems models and methods

CERN Document Server

Buede, Dennis M

2009-01-01

The ideal introduction to the engineering design of systems-now in a new edition. The Engineering Design of Systems, Second Edition compiles a wealth of information from diverse sources to provide a unique, one-stop reference to current methods for systems engineering. It takes a model-based approach to key systems engineering design activities and introduces methods and models used in the real world. Features new to this edition include: * The addition of Systems Modeling Language (SysML) to several of the chapters, as well as the introduction of new terminology * Additional material on partitioning functions and components * More descriptive material on usage scenarios based on literature from use case development * Updated homework assignments * The software product CORE (from Vitech Corporation) is used to generate the traditional SE figures and the software product MagicDraw UML with SysML plugins (from No Magic, Inc.) is used for the SysML figures This book is designed to be an introductory reference ...

Optimal designs for linear mixture models

NARCIS (Netherlands)

Mendieta, E.J.; Linssen, H.N.; Doornbos, R.

1975-01-01

In a recent paper Snee and Marquardt [8] considered designs for linear mixture models, where the components are subject to individual lower and/or upper bounds. When the number of components is large their algorithm XVERT yields designs far too extensive for practical purposes. The purpose of this

The ontology of Gero's FBS  model of designing

DEFF Research Database (Denmark)

Galle, Per

2009-01-01

Recent work by Vermaas and Dorst has led to constructive criticism and conceptual clarification of Gero’s FBS (Function-Behaviour-Structure) model of designing. In this paper Vermaas’ and Dorst’s version of the model is scrutinized, with an emphasis on its temporal aspect and ontological implicat......Recent work by Vermaas and Dorst has led to constructive criticism and conceptual clarification of Gero’s FBS (Function-Behaviour-Structure) model of designing. In this paper Vermaas’ and Dorst’s version of the model is scrutinized, with an emphasis on its temporal aspect and ontological...... implications. Regarding the latter, the model is found to be in need of amendment and further refinement to ensure its clarity and logical coherence. To this end, two alternative modifications of the model are developed. These results are not claimed to be of immediate practical use to designers. Rather...

Using Mathematical Modeling and Set-Based Design Principles to Recommend an Existing CVL Design

Science.gov (United States)

2017-09-01

MATHEMATICAL MODELING AND SET-BASED DESIGN PRINCIPLES TO RECOMMEND AN EXISTING CVL DESIGN by William H. Ehlies September 2017 Thesis Advisor...Office of Management and Budget, Paperwork Reduction Project (0704-0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE...September 2017 3. REPORT TYPE AND DATES COVERED Master’s thesis 4. TITLE AND SUBTITLE USING MATHEMATICAL MODELING AND SET-BASED DESIGN PRINCIPLES

Design of nuclear power generation plants adopting model engineering method

International Nuclear Information System (INIS)

Waki, Masato

1983-01-01

The utilization of model engineering as the method of design has begun about ten years ago in nuclear power generation plants. By this method, the result of design can be confirmed three-dimensionally before actual production, and it is the quick and sure method to meet the various needs in design promptly. The adoption of models aims mainly at the improvement of the quality of design since the high safety is required for nuclear power plants in spite of the complex structure. The layout of nuclear power plants and piping design require the model engineering to arrange rationally enormous quantity of things in a limited period. As the method of model engineering, there are the use of check models and of design models, and recently, the latter method has been mainly taken. The procedure of manufacturing models and engineering is explained. After model engineering has been completed, the model information must be expressed in drawings, and the automation of this process has been attempted by various methods. The computer processing of design is in progress, and its role is explained (CAD system). (Kako, I.)

Verification of aseismic design model by using experimental results

International Nuclear Information System (INIS)

Mizuno, N.; Sugiyama, N.; Suzuki, T.; Shibata, Y.; Miura, K.; Miyagawa, N.

1985-01-01

A lattice model is applied as an analysis model for an aseismic design of the Hamaoka nuclear reactor building. With object to verify an availability of this design model, two reinforced concrete blocks are constructed on the ground and the forced vibration tests are carried out. The test results are well followed by simulation analysis using the lattice model. Damping value of the ground obtained from the test is more conservative than the design value. (orig.)

Engineering graphic modelling a workbook for design engineers

CERN Document Server

Tjalve, E; Frackmann Schmidt, F

2013-01-01

Engineering Graphic Modelling: A Practical Guide to Drawing and Design covers how engineering drawing relates to the design activity. The book describes modeled properties, such as the function, structure, form, material, dimension, and surface, as well as the coordinates, symbols, and types of projection of the drawing code. The text provides drawing techniques, such as freehand sketching, bold freehand drawing, drawing with a straightedge, a draughting machine or a plotter, and use of templates, and then describes the types of drawing. Graphic designers, design engineers, mechanical engine

Integration of Design and Control Through Model Analysis

DEFF Research Database (Denmark)

Russel, Boris Mariboe; Henriksen, Jens Peter; Jørgensen, Sten Bay

2000-01-01

of the phenomena models representing the process model identify the relationships between the important process and design variables, which help to understand, define and address some of the issues related to integration of design and control issues. The model analysis is highlighted through examples involving...... processes with mass and/or energy recycle. (C) 2000 Elsevier Science Ltd. All rights reserved....

Construction of mathematical models the parachute jumper with change position acrobatic

Science.gov (United States)

Asmianto, Asmianto; Hariyanto, Hariyanto; Herisman, Iis

2018-03-01

Construction of mathematical models the movement of a parachutist during the air using newton’s II law is ΣF = ma. Position parachutist after exiting the plane immediately unfurled his body so as to create a large air resistance. The presence of air drag resulting movement indirectly parachutist moves down vertically downwards but also shifting toward horizontal and form a parabolic trajectory. Parachutist speed getting down increased until eventually the parachutist reaches terminal velocity it’s the position where the air drag is equal to the gravitational force (gravity) jumpers. In this paper is assumed to be parachutist with 91.6 kg mass (including equipment) jumping from a plane at an altitude of 3.000 meters and reach a height of parachutist ± 1000 meters with velocity ± 57 m/s. So the parachutist have to be clever in taking account of everything, because if just a little too late can dangerous the safety of the parachutist.

Using physical models to study the gliding performance of extinct animals.

Science.gov (United States)

Koehl, M A R; Evangelista, Dennis; Yang, Karen

2011-12-01

Aerodynamic studies using physical models of fossil organisms can provide quantitative information about how performance of defined activities, such as gliding, depends on specific morphological features. Such analyses allow us to rule out hypotheses about the function of extinct organisms that are not physically plausible and to determine if and how specific morphological features and postures affect performance. The purpose of this article is to provide a practical guide for the design of dynamically scaled physical models to study the gliding of extinct animals using examples from our research on the theropod dinosaur, †Microraptor gui, which had flight feathers on its hind limbs as well as on its forelimbs. Analysis of the aerodynamics of †M. gui can shed light on the design of gliders with large surfaces posterior to the center of mass and provide functional information to evolutionary biologists trying to unravel the origins of flight in the dinosaurian ancestors and sister groups to birds. Measurements of lift, drag, side force, and moments in pitch, roll, and yaw on models in a wind tunnel can be used to calculate indices of gliding and parachuting performance, aerodynamic static stability, and control effectiveness in maneuvering. These indices permit the aerodynamic performance of bodies of different shape, size, stiffness, texture, and posture to be compared and thus can provide insights about the design of gliders, both biological and man-made. Our measurements of maximum lift-to-drag ratios of 2.5-3.1 for physical models of †M. gui suggest that its gliding performance was similar to that of flying squirrels and that the various leg postures that might have been used by †M. gui make little difference to that aspect of aerodynamic performance. We found that body orientation relative to the movement of air past the animal determines whether it is difficult or easy to maneuver.

Process Cost Modeling for Multi-Disciplinary Design Optimization

Science.gov (United States)

Bao, Han P.; Freeman, William (Technical Monitor)

2002-01-01

For early design concepts, the conventional approach to cost is normally some kind of parametric weight-based cost model. There is now ample evidence that this approach can be misleading and inaccurate. By the nature of its development, a parametric cost model requires historical data and is valid only if the new design is analogous to those for which the model was derived. Advanced aerospace vehicles have no historical production data and are nowhere near the vehicles of the past. Using an existing weight-based cost model would only lead to errors and distortions of the true production cost. This report outlines the development of a process-based cost model in which the physical elements of the vehicle are costed according to a first-order dynamics model. This theoretical cost model, first advocated by early work at MIT, has been expanded to cover the basic structures of an advanced aerospace vehicle. Elemental costs based on the geometry of the design can be summed up to provide an overall estimation of the total production cost for a design configuration. This capability to directly link any design configuration to realistic cost estimation is a key requirement for high payoff MDO problems. Another important consideration in this report is the handling of part or product complexity. Here the concept of cost modulus is introduced to take into account variability due to different materials, sizes, shapes, precision of fabrication, and equipment requirements. The most important implication of the development of the proposed process-based cost model is that different design configurations can now be quickly related to their cost estimates in a seamless calculation process easily implemented on any spreadsheet tool. In successive sections, the report addresses the issues of cost modeling as follows. First, an introduction is presented to provide the background for the research work. Next, a quick review of cost estimation techniques is made with the intention to

Designing a Knowledge Management Excellence Model Based on Interpretive Structural Modeling

Directory of Open Access Journals (Sweden)

Mirza Hassan Hosseini

2014-09-01

Full Text Available Despite the development of appropriate academic and experiential background knowledge management and its manifestation as a competitive advantage, many organizations have failed in its effective utilization. Among the reasons for this failure are some deficiencies in terms of methodology in inappropriate recognition and translation of KM dimensions and lack of systematic approach in establishment of causal relationships among KM factors. This article attempts to design an Organizational Knowledge Management Excellence Model. To design an organizational knowledge management excellence model based on library researches, interviews with experts and interpretive-structural modeling (ISM was used in order to identify and determine the relationships between the factors of km excellence. Accordingly, 9 key criteria of KM Excellence as well as 29 sub-criteria were extracted and the relationships and sequence of factors were defined and developed in 5 levels for designing an organizational KM excellence Model. Finally, the concepts were applied in Defense Organizations to illustrate the proposed methodology.

Absorption Cycle Heat Pump Model for Control Design

DEFF Research Database (Denmark)

Vinther, Kasper; Just Nielsen, Rene; Nielsen, Kirsten Mølgaard

2015-01-01

Heat pumps have recently received increasing interest due to green energy initiatives and increasing energy prices. In this paper, a nonlinear dynamic model of a single-effect LiBr-water absorption cycle heat pump is derived for simulation and control design purposes. The model is based on an act......Heat pumps have recently received increasing interest due to green energy initiatives and increasing energy prices. In this paper, a nonlinear dynamic model of a single-effect LiBr-water absorption cycle heat pump is derived for simulation and control design purposes. The model is based...... to operational data and different scenarios are simulated to investigate the operational stability of the heat pump. Finally, this paper provides suggestions and examples of derivation of lower order linear models for control design. © Copyright IEEE - All rights reserved....

Design Change Model for Effective Scheduling Change Propagation Paths

Science.gov (United States)

Zhang, Hai-Zhu; Ding, Guo-Fu; Li, Rong; Qin, Sheng-Feng; Yan, Kai-Yin

2017-09-01

Changes in requirements may result in the increasing of product development project cost and lead time, therefore, it is important to understand how requirement changes propagate in the design of complex product systems and be able to select best options to guide design. Currently, a most approach for design change is lack of take the multi-disciplinary coupling relationships and the number of parameters into account integrally. A new design change model is presented to systematically analyze and search change propagation paths. Firstly, a PDS-Behavior-Structure-based design change model is established to describe requirement changes causing the design change propagation in behavior and structure domains. Secondly, a multi-disciplinary oriented behavior matrix is utilized to support change propagation analysis of complex product systems, and the interaction relationships of the matrix elements are used to obtain an initial set of change paths. Finally, a rough set-based propagation space reducing tool is developed to assist in narrowing change propagation paths by computing the importance of the design change parameters. The proposed new design change model and its associated tools have been demonstrated by the scheduling change propagation paths of high speed train's bogie to show its feasibility and effectiveness. This model is not only supportive to response quickly to diversified market requirements, but also helpful to satisfy customer requirements and reduce product development lead time. The proposed new design change model can be applied in a wide range of engineering systems design with improved efficiency.

Modelling of Context: Designing Mobile Systems from Domain-Dependent Models

DEFF Research Database (Denmark)

Nielsen, Peter Axel; Stage, Jan

2009-01-01

Modelling of domain-dependent aspects is a key prerequisite for the design of software for mobile systems. Most mobile systems include a more or less advanced model of selected aspects of the domain in which they are used. This paper discusses the creation of such a model and its relevance for te...

Recurrent Neural Network Model for Constructive Peptide Design.

Science.gov (United States)

Müller, Alex T; Hiss, Jan A; Schneider, Gisbert

2018-02-26

We present a generative long short-term memory (LSTM) recurrent neural network (RNN) for combinatorial de novo peptide design. RNN models capture patterns in sequential data and generate new data instances from the learned context. Amino acid sequences represent a suitable input for these machine-learning models. Generative models trained on peptide sequences could therefore facilitate the design of bespoke peptide libraries. We trained RNNs with LSTM units on pattern recognition of helical antimicrobial peptides and used the resulting model for de novo sequence generation. Of these sequences, 82% were predicted to be active antimicrobial peptides compared to 65% of randomly sampled sequences with the same amino acid distribution as the training set. The generated sequences also lie closer to the training data than manually designed amphipathic helices. The results of this study showcase the ability of LSTM RNNs to construct new amino acid sequences within the applicability domain of the model and motivate their prospective application to peptide and protein design without the need for the exhaustive enumeration of sequence libraries.

A stage-based model of design teaching

DEFF Research Database (Denmark)

Beier, Sofie

2014-01-01

With a focus on the teaching of design students in higher education, the article will present a teaching approach model that follows the stages of the design process. The model suggests that at the Definition stage, the supervisor can focus on leading the student into a more thorough elaboration ...... apply an approach inspired by the master–apprentice relationship, where the student learns by observing the master at work....

Requirements for High Level Models Supporting Design Space Exploration in Model-based Systems Engineering

OpenAIRE

Haveman, Steven P.; Bonnema, G. Maarten

2013-01-01

Most formal models are used in detailed design and focus on a single domain. Few effective approaches exist that can effectively tie these lower level models to a high level system model during design space exploration. This complicates the validation of high level system requirements during detailed design. In this paper, we define requirements for a high level model that is firstly driven by key systems engineering challenges present in industry and secondly connects to several formal and d...

Integrated design approach of the pebble bed modular using models

International Nuclear Information System (INIS)

Venter, P.J.

2005-01-01

The Pebble Bed Modular Reactor (PBMR) is the first pebble bed reactor that will be utilised in a high temperature direct Brayton cycle configuration. This implies that there are a number of unique features in the PBMR that extend from the German experience base. One of the challenges in the design of the PBMR is managing the integrated design process between the designers, the physicists and the analysts. This integrated design process is managed through model-based development work. Three-dimensional CAD models are constructed of the components and parts in the reactor. From the CAD models, CFD models, neutronic models, shielding models, FEM models and other thermodynamic models are derived. These models range from very simple models to extremely detailed and complex models. The models are used in legacy software as well as commercial off-the-shelf software. The different models are also used in code-to-code comparisons to verify the results. This paper will briefly discuss the different models and the interaction between the models, showing the iterative design process that is used in the development of the reactor at PBMR. (author)

An investigation of modelling and design for software service applications.

Science.gov (United States)

Anjum, Maria; Budgen, David

2017-01-01

Software services offer the opportunity to use a component-based approach for the design of applications. However, this needs a deeper understanding of how to develop service-based applications in a systematic manner, and of the set of properties that need to be included in the 'design model'. We have used a realistic application to explore systematically how service-based designs can be created and described. We first identified the key properties of an SOA (service oriented architecture) and then undertook a single-case case study to explore its use in the development of a design for a large-scale application in energy engineering, modelling this with existing notations wherever possible. We evaluated the resulting design model using two walkthroughs with both domain and application experts. We were able to successfully develop a design model around the ten properties identified, and to describe it by adapting existing design notations. A component-based approach to designing such systems does appear to be feasible. However, it needs the assistance of a more integrated set of notations for describing the resulting design model.

Design of Individualized Wheelchairs Using AHP and Kano Model

Directory of Open Access Journals (Sweden)

Yanli Yuan

2014-06-01

Full Text Available To study how to design different grades of individualized wheelchairs according to users' needs, a personalized wheelchair design method based on AHP and Kano model is proposed. The AHP model determines the relative importance of characteristics of customers' demands. The subfunctions of manual wheelchairs and their attributes are given. The weight coefficients are calculated. 20 experts (10 are the members of the research team, 5 are doctors, and 5 are wheelchair designers are involved in the above two parts of the work. Kano model represents the types of user requirements. 30 participants' (wheelchair users needs are divided into 5 categories: M, O, E, I, and R. According to the types of user needs and the weight of each subfunction, three manual wheelchair models are built. Traditional design method usually cannot satisfy the requirements of users and product structure, so this paper makes a contribution to solve this problem. The method can be used to design individualized wheelchairs which may improve the product quality and customers' satisfaction. Meanwhile it also can reduce the design time, thereby reducing the design cost.

The models that made job design

NARCIS (Netherlands)

Daniels, K.; Le Blanc, P.M.; Davis, M.; Peeters, M.; Jonge, de J.; Taris, T.

2014-01-01

It is the purpose of this chapter to describe and evaluate five of the most significant approaches to job design that have laid the foundation for contemporary work psychology: the Job Characteristics Model (JCM; Hackman & Oldham, 1976, Section 3.2), the Demand–Control–Support Model (DCSM; Karasek &

Designing Customer Relationship Management Model in Hospital

OpenAIRE

Mohammad Abbaszadeh; Roohollah Askari; Morad Alizadeh; Mohammad Amin Bahrami

2017-01-01

Background: Customer relationship management is a modern marketing concept which is also considered as a successful business strategy. The present study aimed to design a customer relationship management model in the hospital. Methods: The study is an applied research performed in 2 phases of 1) texts investigation and 2) the experts' opinions to achieve consensus. Data were analyzed using SPSS 18 software along with descriptive statistics. Results: The designed model included areas of ...

Conceptual Model of Artifacts for Design Science Research

DEFF Research Database (Denmark)

Bækgaard, Lars

2015-01-01

We present a conceptual model of design science research artifacts. The model views an artifact at three levels. At the artifact level a selected artifact is viewed as a combination of material and immaterial aspects and a set of representations hereof. At the design level the selected artifact...

Orion Boiler Plate Airdrop Test System

Science.gov (United States)

Machin, Ricardo A.; Evans, Carol T.

2013-01-01

On the 29th of February 2012 the Orion Capsule Parachute Assembly System (CPAS) project attempted to perform an airdrop test of a boilerplate test article for the second time. The first attempt (Cluster Development Test 2, July 2008) to deliver a similar boilerplate from a C-17 using the Low Velocity Air Drop (LVAD) technique resulted in the programmer parachute failing to properly inflate, the test article failing to achieve the desired test initiation conditions, and the test article a total loss. This paper will pick up where the CDT-2 failure investigation left off, describing the test technique that was adopted, and outline the modeling that was performed to gain confidence that the second attempt would be successful. The second boiler plate test (Cluster Development Test 3-3) was indeed a complete success and has subsequently been repeated several times, allowing the CPAS project to proceed with the full scale system level development testing required to integrate the hardware to the first Entry Flight Test vehicle as well as go into the Critical Design Review with minimum risk and a mature design.

Modelling root reinforcement in shallow forest soils

Science.gov (United States)

Skaugset, Arne E.

1997-01-01

A hypothesis used to explain the relationship between timber harvesting and landslides is that tree roots add mechanical support to soil, thus increasing soil strength. Upon harvest, the tree roots decay which reduces soil strength and increases the risk of management -induced landslides. The technical literature does not adequately support this hypothesis. Soil strength values attributed to root reinforcement that are in the technical literature are such that forested sites can't fail and all high risk, harvested sites must fail. Both unstable forested sites and stable harvested sites exist, in abundance, in the real world thus, the literature does not adequately describe the real world. An analytical model was developed to calculate soil strength increase due to root reinforcement. Conceptually, the model is composed of a reinforcing element with high tensile strength, i.e. a conifer root, embedded in a material with little tensile strength, i.e. a soil. As the soil fails and deforms, the reinforcing element also deforms and stretches. The lateral deformation of the reinforcing element is treated analytically as a laterally loaded pile in a flexible foundation and the axial deformation is treated as an axially loaded pile. The governing differential equations are solved using finite-difference approximation techniques. The root reinforcement model was tested by comparing the final shape of steel and aluminum rods, parachute cord, wooden dowels, and pine roots in direct shear with predicted shapes from the output of the root reinforcement model. The comparisons were generally satisfactory, were best for parachute cord and wooden dowels, and were poorest for steel and aluminum rods. A parameter study was performed on the root reinforcement model which showed reinforced soil strength increased with increasing root diameter and soil depth. Output from the root reinforcement model showed a strain incompatibility between large and small diameter roots. The peak

Analysis and Comparison of Typical Models within Distribution Network Design

DEFF Research Database (Denmark)

Jørgensen, Hans Jacob; Larsen, Allan; Madsen, Oli B.G.

This paper investigates the characteristics of typical optimisation models within Distribution Network Design. During the paper fourteen models known from the literature will be thoroughly analysed. Through this analysis a schematic approach to categorisation of distribution network design models...... for educational purposes. Furthermore, the paper can be seen as a practical introduction to network design modelling as well as a being an art manual or recipe when constructing such a model....

A User-centered Model for Web Site Design

Science.gov (United States)

Kinzie, Mable B.; Cohn, Wendy F.; Julian, Marti F.; Knaus, William A.

2002-01-01

As the Internet continues to grow as a delivery medium for health information, the design of effective Web sites becomes increasingly important. In this paper, the authors provide an overview of one effective model for Web site design, a user-centered process that includes techniques for needs assessment, goal/task analysis, user interface design, and rapid prototyping. They detail how this approach was employed to design a family health history Web site, Health Heritage . This Web site helps patients record and maintain their family health histories in a secure, confidential manner. It also supports primary care physicians through analysis of health histories, identification of potential risks, and provision of health care recommendations. Visual examples of the design process are provided to show how the use of this model resulted in an easy-to-use Web site that is likely to meet user needs. The model is effective across diverse content arenas and is appropriate for applications in varied media. PMID:12087113

Integration of Design and Control through Model Analysis

DEFF Research Database (Denmark)

Russel, Boris Mariboe; Henriksen, Jens Peter; Jørgensen, Sten Bay

2002-01-01

A systematic computer aided analysis of the process model is proposed as a pre-solution step for integration of design and control problems. The process model equations are classified in terms of balance equations, constitutive equations and conditional equations. Analysis of the phenomena models...... (structure selection) issues for the integrated problems are considered. (C) 2002 Elsevier Science Ltd. All rights reserved....... representing the constitutive equations identify the relationships between the important process and design variables, which help to understand, define and address some of the issues related to integration of design and control. Furthermore, the analysis is able to identify a set of process (control) variables...

Design, Modelling and Analysis of a Workflow Reconfiguration

DEFF Research Database (Denmark)

Mazzara, Manuel; Abouzaid, Faisal; Dragoni, Nicola

2011-01-01

This paper describes a case study involving the reconfiguration of an office workflow. We state the requirements on a system implementing the workflow and its reconfiguration, and describe the system’s design in BPMN. We then use an asynchronous pi-calculus and Web.1 to model the design and to ve......This paper describes a case study involving the reconfiguration of an office workflow. We state the requirements on a system implementing the workflow and its reconfiguration, and describe the system’s design in BPMN. We then use an asynchronous pi-calculus and Web.1 to model the design...

Group Contribution Based Process Flowsheet Synthesis, Design and Modelling

DEFF Research Database (Denmark)

d'Anterroches, Loïc; Gani, Rafiqul

2004-01-01

This paper presents a process-group-contribution Method to model. simulate and synthesize a flowsheet. The process-group based representation of a flowsheet together with a process "property" model are presented. The process-group based synthesis method is developed on the basis of the computer...... aided molecular design methods and gives the ability to screen numerous process alternatives without the need to use the rigorous process simulation models. The process "property" model calculates the design targets for the generated flowsheet alternatives while a reverse modelling method (also...... developed) determines the design variables matching the target. A simple illustrative example highlighting the main features of the methodology is also presented....

Modeling and simulation for process and safeguards system design

International Nuclear Information System (INIS)

Gutmacher, R.G.; Kern, E.A.; Duncan, D.R.; Benecke, M.W.

1983-01-01

A computer modeling and simulation approach that meets the needs of both the process and safeguards system designers is described. The results have been useful to Westinghouse Hanford Company process designers in optimizing the process scenario and operating scheme of the Secure Automated Fabrication line. The combined process/measurements model will serve as the basis for design of the safeguards system. Integration of the process design and the safeguards system design should result in a smoothly operating process that is easier to safeguard

Assessment of slip factor models at off-design condition

International Nuclear Information System (INIS)

Yoon, Sung Ho; Baek, Je Hyun

2000-01-01

Slip factor is defined as an empirical factor being multiplied to theoretical energy transfer for the estimation of real work input of a centrifugal compressor. Researchers have tried to develop a simple empirical model, for a century, to predict a slip factor. However most these models were developed on the condition of design point assuming inviscid flow. So these models often fail to predict a correct slip factor at off-design condition. In this study, we summarized various slip factor models and compared these models with experimental and numerical data at off-design condition. As a result of this study, Wiesner's and Paeng and Chung's models are applicable for radial impeller, but all the models are not suitable for backswept impeller. Finally, the essential avenues for future study is discussed

The RHIC/AGS Online Model Environment: Design and Overview

International Nuclear Information System (INIS)

Satogata, T.; Brown, K.; Pilat, F.; Tafti Alai, A.; Tepikian, S.; Vanzeijtz

1999-01-01

An integrated online modeling environment is currently under development for use by AGS and RHIC physicists and commissioners. This environment combines the modeling efforts of both groups in a CDEV[1] client-server design, providing access to expected machine optics and physics parameters based on live and design machine settings. An abstract modeling interface has been designed as a set of adapters[2] around core computational modeling engines such as MAD and UAL/Teapot++[3]. This approach allows us to leverage existing survey, lattice, and magnet infrastructure, as well as easily incorporate new model engine developments. This paper describes the architecture of the RHIC/AGS modeling environment, including the application interface through CDEV and general tools for graphical interaction with the model using Tcl/Tk. Separate papers at this conference address the specifics of implementation and modeling experience for AGS and RHIC

Guidance, Navigation and Control (GN and C) Design Overview and Flight Test Results from NASA's Max Launch Abort System (MLAS)

Science.gov (United States)

Dennehy, Cornelius J.; Lanzi, Raymond J.; Ward, Philip R.

2010-01-01

The National Aeronautics and Space Administration Engineering and Safety Center designed, developed and flew the alternative Max Launch Abort System (MLAS) as risk mitigation for the baseline Orion spacecraft launch abort system already in development. The NESC was tasked with both formulating a conceptual objective system design of this alternative MLAS as well as demonstrating this concept with a simulated pad abort flight test. Less than 2 years after Project start the MLAS simulated pad abort flight test was successfully conducted from Wallops Island on July 8, 2009. The entire flight test duration was 88 seconds during which time multiple staging events were performed and nine separate critically timed parachute deployments occurred as scheduled. This paper provides an overview of the guidance navigation and control technical approaches employed on this rapid prototyping activity; describes the methodology used to design the MLAS flight test vehicle; and lessons that were learned during this rapid prototyping project are also summarized.

A domain-independent descriptive design model and its application to structured reflection on design processes

NARCIS (Netherlands)

Reymen, Isabelle; Hammer, D.K.; Kroes, P.A.; van Aken, Joan Ernst; van Aken, J.E.; Dorst, C.H.; Bax, M.F.T.; Basten, T

2006-01-01

Domain-independent models of the design process are an important means for facilitating interdisciplinary communication and for supporting multidisciplinary design. Many so-called domain-independent models are, however, not really domain independent. We state that to be domain independent, the

Model-based design approaches for plug-in hybrid vehicle design

Energy Technology Data Exchange (ETDEWEB)

Mendes, C.J. [CrossChasm Technologies, Cambridge, ON (Canada); Stevens, M.B.; Fowler, M.W. [Waterloo Univ., ON (Canada). Dept. of Chemical Engineering; Fraser, R.A. [Waterloo Univ., ON (Canada). Dept. of Mechanical Engineering; Wilhelm, E.J. [Paul Scherrer Inst., Villigen (Switzerland). Energy Systems Analysis

2007-07-01

A model-based design process for plug-in hybrid vehicles (PHEVs) was presented. The paper discussed steps between the initial design concept and a working vehicle prototype, and focused on an investigation of the software-in-the-loop (SIL), hardware-in-the-loop (HIL), and component-in-the-loop (CIL) design phases. The role and benefits of using simulation were also reviewed. A method for mapping and identifying components was provided along with a hybrid control strategy and component-level control optimization process. The role of simulation in component evaluation, architecture design, and de-bugging procedures was discussed, as well as the role simulation networks can play in speeding deployment times. The simulations focused on work performed on a 2005 Chevrolet Equinox converted to a fuel cell hybrid electric vehicle (FCHEV). Components were aggregated to create a complete virtual vehicle. A simplified vehicle model was implemented onto the on-board vehicle control hardware. Optimization metrics were estimated at 10 alpha values during each control loop iteration. The simulation was then used to tune the control system under a variety of drive cycles and conditions. A CIL technique was used to place a physical hybrid electric vehicle (HEV) component under the control of a real time HEV/PHEV simulation. It was concluded that controllers should have a standardized component description that supports integration into advanced testing procedures. 4 refs., 9 figs.

Requirements for high level models supporting design space exploration in model-based systems engineering

NARCIS (Netherlands)

Haveman, Steven; Bonnema, Gerrit Maarten

2013-01-01

Most formal models are used in detailed design and focus on a single domain. Few effective approaches exist that can effectively tie these lower level models to a high level system model during design space exploration. This complicates the validation of high level system requirements during

The "Parachute" Technique: A Simple and Effective Single-Row Procedure to Achieve an Increased Contact Area Between the Cuff-Tendon and Its Footprint.

Science.gov (United States)

Natera, Luis; Consigliere, Paolo; Witney-Lagen, Caroline; Brugera, Juan; Sforza, Giuseppe; Atoun, Ehud; Levy, Ofer

2017-10-01

Many techniques of arthroscopic rotator cuff repair have been described. No significant differences in clinical outcomes or rerupture rates have been observed when comparing single-row with double-row methods. Not all single- and double-row repairs are the same. The details of the technique used are crucial. It has been shown that the suture-tendon interface is the weakest point of the reconstruction. Therefore, the biomechanical properties of rotator cuff repairs might be influenced more by the suture configuration than by the number of anchors or by the number of rows involved. Techniques that secure less amount of tendon over a smaller area of the healing zone might be expected to have higher failure rates. The way the sutures of the "parachute technique" are configured represents a quadruple mattress that increases the contact and pressure between the tendon and its footprint and increases the primary load to failure of the repair. We present a simple and effective single-row technique that involves the biomechanical and biological advantages related to the increased contact area and pressure between the cuff and its footprint.

Evaluating procedural modelling for 3D models of informal settlements in urban design activities

Directory of Open Access Journals (Sweden)

Victoria Rautenbach

2015-11-01

Full Text Available Three-dimensional (3D modelling and visualisation is one of the fastest growing application fields in geographic information science. 3D city models are being researched extensively for a variety of purposes and in various domains, including urban design, disaster management, education and computer gaming. These models typically depict urban business districts (downtown or suburban residential areas. Despite informal settlements being a prevailing feature of many cities in developing countries, 3D models of informal settlements are virtually non-existent. 3D models of informal settlements could be useful in various ways, e.g. to gather information about the current environment in the informal settlements, to design upgrades, to communicate these and to educate inhabitants about environmental challenges. In this article, we described the development of a 3D model of the Slovo Park informal settlement in the City of Johannesburg Metropolitan Municipality, South Africa. Instead of using time-consuming traditional manual methods, we followed the procedural modelling technique. Visualisation characteristics of 3D models of informal settlements were described and the importance of each characteristic in urban design activities for informal settlement upgrades was assessed. Next, the visualisation characteristics of the Slovo Park model were evaluated. The results of the evaluation showed that the 3D model produced by the procedural modelling technique is suitable for urban design activities in informal settlements. The visualisation characteristics and their assessment are also useful as guidelines for developing 3D models of informal settlements. In future, we plan to empirically test the use of such 3D models in urban design projects in informal settlements.

ExaSAT: An exascale co-design tool for performance modeling

International Nuclear Information System (INIS)

Unat, Didem; Chan, Cy; Zhang, Weiqun; Williams, Samuel; Bachan, John

2015-01-01

One of the emerging challenges to designing HPC systems is understanding and projecting the requirements of exascale applications. In order to determine the performance consequences of different hardware designs, analytic models are essential because they can provide fast feedback to the co-design centers and chip designers without costly simulations. However, current attempts to analytically model program performance typically rely on the user manually specifying a performance model. Here we introduce the ExaSAT framework that automates the extraction of parameterized performance models directly from source code using compiler analysis. The parameterized analytic model enables quantitative evaluation of a broad range of hardware design trade-offs and software optimizations on a variety of different performance metrics, with a primary focus on data movement as a metric. Finally, we demonstrate the ExaSAT framework’s ability to perform deep code analysis of a proxy application from the Department of Energy Combustion Co-design Center to illustrate its value to the exascale co-design process. ExaSAT analysis provides insights into the hardware and software trade-offs and lays the groundwork for exploring a more targeted set of design points using cycle-accurate architectural simulators.

An investigation of modelling and design for software service applications

Science.gov (United States)

2017-01-01

Software services offer the opportunity to use a component-based approach for the design of applications. However, this needs a deeper understanding of how to develop service-based applications in a systematic manner, and of the set of properties that need to be included in the ‘design model’. We have used a realistic application to explore systematically how service-based designs can be created and described. We first identified the key properties of an SOA (service oriented architecture) and then undertook a single-case case study to explore its use in the development of a design for a large-scale application in energy engineering, modelling this with existing notations wherever possible. We evaluated the resulting design model using two walkthroughs with both domain and application experts. We were able to successfully develop a design model around the ten properties identified, and to describe it by adapting existing design notations. A component-based approach to designing such systems does appear to be feasible. However, it needs the assistance of a more integrated set of notations for describing the resulting design model. PMID:28489905

Integrating Surface Modeling into the Engineering Design Graphics Curriculum

Science.gov (United States)

Hartman, Nathan W.

2006-01-01

It has been suggested there is a knowledge base that surrounds the use of 3D modeling within the engineering design process and correspondingly within engineering design graphics education. While solid modeling receives a great deal of attention and discussion relative to curriculum efforts, and rightly so, surface modeling is an equally viable 3D…

Experimental designs for autoregressive models applied to industrial maintenance

International Nuclear Information System (INIS)

Amo-Salas, M.; López-Fidalgo, J.; Pedregal, D.J.

2015-01-01

Some time series applications require data which are either expensive or technically difficult to obtain. In such cases scheduling the points in time at which the information should be collected is of paramount importance in order to optimize the resources available. In this paper time series models are studied from a new perspective, consisting in the use of Optimal Experimental Design setup to obtain the best times to take measurements, with the principal aim of saving costs or discarding useless information. The model and the covariance function are expressed in an explicit form to apply the usual techniques of Optimal Experimental Design. Optimal designs for various approaches are computed and their efficiencies are compared. The methods working in an application of industrial maintenance of a critical piece of equipment at a petrochemical plant are shown. This simple model allows explicit calculations in order to show openly the procedure to find the correlation structure, needed for computing the optimal experimental design. In this sense the techniques used in this paper to compute optimal designs may be transferred to other situations following the ideas of the paper, but taking into account the increasing difficulty of the procedure for more complex models. - Highlights: • Optimal experimental design theory is applied to AR models to reduce costs. • The first observation has an important impact on any optimal design. • Either the lack of precision or small starting observations claim for large times. • Reasonable optimal times were obtained relaxing slightly the efficiency. • Optimal designs were computed in a predictive maintenance context

Design, modeling and testing of data converters

CERN Document Server

Kiaei, Sayfe; Xu, Fang

2014-01-01

This book presents the a scientific discussion of the state-of-the-art techniques and designs for modeling, testing and for the performance analysis of data converters. The focus is put on sustainable data conversion. Sustainability has become a public issue that industries and users can not ignore. Devising environmentally friendly solutions for data conversion designing, modeling and testing is nowadays a requirement that researchers and practitioners must consider in their activities. This book presents the outcome of the IWADC workshop 2011, held in Orvieto, Italy.

Reentry Vehicle Flight Controls Design Guidelines: Dynamic Inversion

Science.gov (United States)

Ito, Daigoro; Georgie, Jennifer; Valasek, John; Ward, Donald T.

2002-01-01

This report addresses issues in developing a flight control design for vehicles operating across a broad flight regime and with highly nonlinear physical descriptions of motion. Specifically it addresses the need for reentry vehicles that could operate through reentry from space to controlled touchdown on Earth. The latter part of controlled descent is achieved by parachute or paraglider - or by all automatic or a human-controlled landing similar to that of the Orbiter. Since this report addresses the specific needs of human-carrying (not necessarily piloted) reentry vehicles, it deals with highly nonlinear equations of motion, and then-generated control systems must be robust across a very wide range of physics. Thus, this report deals almost exclusively with some form of dynamic inversion (DI). Two vital aspects of control theory - noninteracting control laws and the transformation of nonlinear systems into equivalent linear systems - are embodied in DI. Though there is no doubt that the mathematical tools and underlying theory are widely available, there are open issues as to the practicality of using DI as the only or primary design approach for reentry articles. This report provides a set of guidelines that can be used to determine the practical usefulness of the technique.

Design and analysis of information model hotel complex

Directory of Open Access Journals (Sweden)

Garyaev Nikolai

2016-01-01

Full Text Available The article analyzes the innovation in 3D modeling and development of process design approaches based on visualization of information technology and computer-aided design systems. The problems arising in the modern design and the approach to address them.

Model-Based Requirements Management in Gear Systems Design Based On Graph-Based Design Languages

Directory of Open Access Journals (Sweden)

Kevin Holder

2017-10-01

Full Text Available For several decades, a wide-spread consensus concerning the enormous importance of an in-depth clarification of the specifications of a product has been observed. A weak clarification of specifications is repeatedly listed as a main cause for the failure of product development projects. Requirements, which can be defined as the purpose, goals, constraints, and criteria associated with a product development project, play a central role in the clarification of specifications. The collection of activities which ensure that requirements are identified, documented, maintained, communicated, and traced throughout the life cycle of a system, product, or service can be referred to as “requirements engineering”. These activities can be supported by a collection and combination of strategies, methods, and tools which are appropriate for the clarification of specifications. Numerous publications describe the strategy and the components of requirements management. Furthermore, recent research investigates its industrial application. Simultaneously, promising developments of graph-based design languages for a holistic digital representation of the product life cycle are presented. Current developments realize graph-based languages by the diagrams of the Unified Modelling Language (UML, and allow the automatic generation and evaluation of multiple product variants. The research presented in this paper seeks to present a method in order to combine the advantages of a conscious requirements management process and graph-based design languages. Consequently, the main objective of this paper is the investigation of a model-based integration of requirements in a product development process by means of graph-based design languages. The research method is based on an in-depth analysis of an exemplary industrial product development, a gear system for so-called “Electrical Multiple Units” (EMU. Important requirements were abstracted from a gear system

Design of reconfigurable antennas using graph models

CERN Document Server

Costantine, Joseph; Christodoulou, Christos G; Christodoulou, Christos G

2013-01-01

This lecture discusses the use of graph models to represent reconfigurable antennas. The rise of antennas that adapt to their environment and change their operation based on the user's request hasn't been met with clear design guidelines. There is a need to propose some rules for the optimization of any reconfigurable antenna design and performance. Since reconfigurable antennas are seen as a collection of self-organizing parts, graph models can be introduced to relate each possible topology to a corresponding electromagnetic performance in terms of achieving a characteristic frequency of oper

Robust control design verification using the modular modeling system

International Nuclear Information System (INIS)

Edwards, R.M.; Ben-Abdennour, A.; Lee, K.Y.

1991-01-01

The Modular Modeling System (B ampersand W MMS) is being used as a design tool to verify robust controller designs for improving power plant performance while also providing fault-accommodating capabilities. These controllers are designed based on optimal control theory and are thus model based controllers which are targeted for implementation in a computer based digital control environment. The MMS is being successfully used to verify that the controllers are tolerant of uncertainties between the plant model employed in the controller and the actual plant; i.e., that they are robust. The two areas in which the MMS is being used for this purpose is in the design of (1) a reactor power controller with improved reactor temperature response, and (2) the design of a multiple input multiple output (MIMO) robust fault-accommodating controller for a deaerator level and pressure control problem

Methodology for Designing Models Predicting Success of Infertility Treatment

OpenAIRE

Alireza Zarinara; Mohammad Mahdi Akhondi; Hojjat Zeraati; Koorsh Kamali; Kazem Mohammad

2016-01-01

Abstract Background: The prediction models for infertility treatment success have presented since 25 years ago. There are scientific principles for designing and applying the prediction models that is also used to predict the success rate of infertility treatment. The purpose of this study is to provide basic principles for designing the model to predic infertility treatment success. Materials and Methods: In this paper, the principles for developing predictive models are explained and...

Understanding Creative Design Processes by Integrating Sketching and CAD Modelling Design Environments: A Preliminary Protocol Result from Architectural Designers

Directory of Open Access Journals (Sweden)

Yi Teng Shih

2015-11-01

Full Text Available This paper presents the results of a preliminary protocol study of the cognitive behaviour of architectural designers during the design process. The aim is to better understand the similarities and differences in cognitive behaviour using Sequential Mixed Media (SMM and Alternative Mixed Media (AMM approaches, and how switching between media may impact on design processes. Two participants with at least one-year’s professional design experience and a Bachelor of Design degree, and competence in both sketching and computer-aid design (CAD modelling participated in the study. Video recordings of participants working on different projects were coded using the Function-Behaviour-Structure (FBS coding scheme. Participants were also interviewed and their explanations about their switching behaviours were categorised into three types: S→C, S/C↹R and C→S. Preliminary results indicate that switching between media may influence how designers identify problems and develop solutions. In particular, two design issues were identified.  These relate to the FBS coding scheme, where structure (S and behaviour derived from structure (Bs, change to documentation (D after switching from sketching to CAD modelling (S→C. These switches make it possible for designers to integrate both approaches into one design medium and facilitate their design processes in AMM design environments.

Mars Science Laboratory Entry Guidance Improvements for Mars 2018 (DRAFT)

Science.gov (United States)

Garcia-Llama, Eduardo; Winski, Richard G.; Shidner, Jeremy D.; Ivanov, Mark C.; Grover, Myron R.; Prakash, Ravi

2011-01-01

In 2011, the Mars Science Laboratory (MSL) will be launched in a mission to deliver the largest and most capable rover to date to the surface of Mars. A follow on MSL-derived mission, referred to as Mars 2018, is planned for 2018. Mars 2018 goals include performance enhancements of the Entry, Descent and Landing over that of its predecessor MSL mission of 2011. This paper will discuss the main elements of the modified 2018 EDL preliminary design that will increase performance on the entry phase of the mission. In particular, these elements will increase the parachute deploy altitude to allow for more time margin during the subsequent descent and landing phases and reduce the delivery ellipse size at parachute deploy through modifications in the entry reference trajectory design, guidance trigger logic design, and the effect of additional navigation hardware.

A Perspective on Computational Human Performance Models as Design Tools

Science.gov (United States)

Jones, Patricia M.

2010-01-01

The design of interactive systems, including levels of automation, displays, and controls, is usually based on design guidelines and iterative empirical prototyping. A complementary approach is to use computational human performance models to evaluate designs. An integrated strategy of model-based and empirical test and evaluation activities is particularly attractive as a methodology for verification and validation of human-rated systems for commercial space. This talk will review several computational human performance modeling approaches and their applicability to design of display and control requirements.

Design and competitive edge: A model for design management excellence in European SME's

OpenAIRE

Borja de Mozota, B

2002-01-01

This article suggests to use the conceptual model of Michael Porter Value Chain in order to integrate all the variables that explain the mechanism of value creation through design. The results of the study of 33 European SMES participating in the European Design Prize explain the role of design in the management of innovation, identify the variables that characterize design management and classify them according to the value chain concept. The main result of this research was the ...

Uniform design based SVM model selection for face recognition

Science.gov (United States)

Li, Weihong; Liu, Lijuan; Gong, Weiguo

2010-02-01

Support vector machine (SVM) has been proved to be a powerful tool for face recognition. The generalization capacity of SVM depends on the model with optimal hyperparameters. The computational cost of SVM model selection results in application difficulty in face recognition. In order to overcome the shortcoming, we utilize the advantage of uniform design--space filling designs and uniformly scattering theory to seek for optimal SVM hyperparameters. Then we propose a face recognition scheme based on SVM with optimal model which obtained by replacing the grid and gradient-based method with uniform design. The experimental results on Yale and PIE face databases show that the proposed method significantly improves the efficiency of SVM model selection.

Low-order aeroelastic models of wind turbines for controller design

DEFF Research Database (Denmark)

Sønderby, Ivan Bergquist

Wind turbine controllers are used to optimize the performance of wind turbines such as to reduce power variations and fatigue and extreme loads on wind turbine components. Accurate tuning and design of modern controllers must be done using low-order models that accurately captures the aeroelastic...... response of the wind turbine. The purpose of this thesis is to investigate the necessary model complexity required in aeroelastic models used for controller design and to analyze and propose methods to design low-order aeroelastic wind turbine models that are suited for model-based control design....... The thesis contains a characterization of the dynamics that influence the open-loop aeroelastic frequency response of a modern wind turbine, based on a high-order aeroelastic wind turbine model. One main finding is that the transfer function from collective pitch to generator speed is affected by two low...

Consistent Stochastic Modelling of Meteocean Design Parameters

DEFF Research Database (Denmark)

Sørensen, John Dalsgaard; Sterndorff, M. J.

2000-01-01

Consistent stochastic models of metocean design parameters and their directional dependencies are essential for reliability assessment of offshore structures. In this paper a stochastic model for the annual maximum values of the significant wave height, and the associated wind velocity, current...

A Generative Computer Model for Preliminary Design of Mass Housing

Directory of Open Access Journals (Sweden)

Ahmet Emre DİNÇER

2014-05-01

Full Text Available Today, we live in what we call the “Information Age”, an age in which information technologies are constantly being renewed and developed. Out of this has emerged a new approach called “Computational Design” or “Digital Design”. In addition to significantly influencing all fields of engineering, this approach has come to play a similar role in all stages of the design process in the architectural field. In providing solutions for analytical problems in design such as cost estimate, circulation systems evaluation and environmental effects, which are similar to engineering problems, this approach is being used in the evaluation, representation and presentation of traditionally designed buildings. With developments in software and hardware technology, it has evolved as the studies based on design of architectural products and production implementations with digital tools used for preliminary design stages. This paper presents a digital model which may be used in the preliminary stage of mass housing design with Cellular Automata, one of generative design systems based on computational design approaches. This computational model, developed by scripts of 3Ds Max software, has been implemented on a site plan design of mass housing, floor plan organizations made by user preferences and facade designs. By using the developed computer model, many alternative housing types could be rapidly produced. The interactive design tool of this computational model allows the user to transfer dimensional and functional housing preferences by means of the interface prepared for model. The results of the study are discussed in the light of innovative architectural approaches.

Aspect-oriented security hardening of UML design models

CERN Document Server

Mouheb, Djedjiga; Pourzandi, Makan; Wang, Lingyu; Nouh, Mariam; Ziarati, Raha; Alhadidi, Dima; Talhi, Chamseddine; Lima, Vitor

2015-01-01

This book comprehensively presents a novel approach to the systematic security hardening of software design models expressed in the standard UML language. It combines model-driven engineering and the aspect-oriented paradigm to integrate security practices into the early phases of the software development process. To this end, a UML profile has been developed for the specification of security hardening aspects on UML diagrams. In addition, a weaving framework, with the underlying theoretical foundations, has been designed for the systematic injection of security aspects into UML models. The

Assessing model-based reasoning using evidence-centered design a suite of research-based design patterns

CERN Document Server

Mislevy, Robert J; Riconscente, Michelle; Wise Rutstein, Daisy; Ziker, Cindy

2017-01-01

This Springer Brief provides theory, practical guidance, and support tools to help designers create complex, valid assessment tasks for hard-to-measure, yet crucial, science education standards. Understanding, exploring, and interacting with the world through models characterizes science in all its branches and at all levels of education. Model-based reasoning is central to science education and thus science assessment. Current interest in developing and using models has increased with the release of the Next Generation Science Standards, which identified this as one of the eight practices of science and engineering. However, the interactive, complex, and often technology-based tasks that are needed to assess model-based reasoning in its fullest forms are difficult to develop. Building on research in assessment, science education, and learning science, this Brief describes a suite of design patterns that can help assessment designers, researchers, and teachers create tasks for assessing aspects of model-based...

Computer-aided design of curved surfaces with automatic model generation

Science.gov (United States)

Staley, S. M.; Jerard, R. B.; White, P. R.

1980-01-01

The design and visualization of three-dimensional objects with curved surfaces have always been difficult. The paper given below describes a computer system which facilitates both the design and visualization of such surfaces. The system enhances the design of these surfaces by virtue of various interactive techniques coupled with the application of B-Spline theory. Visualization is facilitated by including a specially built model-making machine which produces three-dimensional foam models. Thus, the system permits the designer to produce an inexpensive model of the object which is suitable for evaluation and presentation.

MEMS 3-DoF gyroscope design, modeling and simulation through equivalent circuit lumped parameter model

International Nuclear Information System (INIS)

Mian, Muhammad Umer; Khir, M. H. Md.; Tang, T. B.; Dennis, John Ojur; Riaz, Kashif; Iqbal, Abid; Bazaz, Shafaat A.

2015-01-01

Pre-fabrication, behavioural and performance analysis with computer aided design (CAD) tools is a common and fabrication cost effective practice. In light of this we present a simulation methodology for a dual-mass oscillator based 3 Degree of Freedom (3-DoF) MEMS gyroscope. 3-DoF Gyroscope is modeled through lumped parameter models using equivalent circuit elements. These equivalent circuits consist of elementary components which are counterpart of their respective mechanical components, used to design and fabricate 3-DoF MEMS gyroscope. Complete designing of equivalent circuit model, mathematical modeling and simulation are being presented in this paper. Behaviors of the equivalent lumped models derived for the proposed device design are simulated in MEMSPRO T-SPICE software. Simulations are carried out with the design specifications following design rules of the MetalMUMPS fabrication process. Drive mass resonant frequencies simulated by this technique are 1.59 kHz and 2.05 kHz respectively, which are close to the resonant frequencies found by the analytical formulation of the gyroscope. The lumped equivalent circuit modeling technique proved to be a time efficient modeling technique for the analysis of complex MEMS devices like 3-DoF gyroscopes. The technique proves to be an alternative approach to the complex and time consuming couple field analysis Finite Element Analysis (FEA) previously used

MEMS 3-DoF gyroscope design, modeling and simulation through equivalent circuit lumped parameter model

Energy Technology Data Exchange (ETDEWEB)

Mian, Muhammad Umer, E-mail: umermian@gmail.com; Khir, M. H. Md.; Tang, T. B. [Department of Electrical and Electronic Engineering, Universiti Teknologi PETRONAS, Tronoh, Perak (Malaysia); Dennis, John Ojur [Department of Fundamental & Applied Sciences, Universiti Teknologi PETRONAS, Tronoh, Perak (Malaysia); Riaz, Kashif; Iqbal, Abid [Faculty of Electronics Engineering, GIK Institute of Engineering Sciences and Technology, Topi, Khyber Pakhtunkhaw (Pakistan); Bazaz, Shafaat A. [Department of Computer Science, Center for Advance Studies in Engineering, Islamabad (Pakistan)

2015-07-22

Pre-fabrication, behavioural and performance analysis with computer aided design (CAD) tools is a common and fabrication cost effective practice. In light of this we present a simulation methodology for a dual-mass oscillator based 3 Degree of Freedom (3-DoF) MEMS gyroscope. 3-DoF Gyroscope is modeled through lumped parameter models using equivalent circuit elements. These equivalent circuits consist of elementary components which are counterpart of their respective mechanical components, used to design and fabricate 3-DoF MEMS gyroscope. Complete designing of equivalent circuit model, mathematical modeling and simulation are being presented in this paper. Behaviors of the equivalent lumped models derived for the proposed device design are simulated in MEMSPRO T-SPICE software. Simulations are carried out with the design specifications following design rules of the MetalMUMPS fabrication process. Drive mass resonant frequencies simulated by this technique are 1.59 kHz and 2.05 kHz respectively, which are close to the resonant frequencies found by the analytical formulation of the gyroscope. The lumped equivalent circuit modeling technique proved to be a time efficient modeling technique for the analysis of complex MEMS devices like 3-DoF gyroscopes. The technique proves to be an alternative approach to the complex and time consuming couple field analysis Finite Element Analysis (FEA) previously used.

Influence of mathematical models in design of PV-Diesel systems

International Nuclear Information System (INIS)

Dufo-Lopez, Rodolfo; Bernal-Agustin, Jose L.

2008-01-01

This paper presents a study of the influence of mathematical models in the optimal design of PV-Diesel systems. For this purpose, a design tool developed by the authors, which allows obtaining the most cost effective design of a PV-Diesel system through the genetic algorithm technique, has been used. The mathematical models of some elements of the hybrid system have been improved in comparison to those usually employed in hybrid systems design programs. Furthermore, a more complete general control strategy has been developed, one that also takes into account more characteristics than those usually considered in this kind of design. Several designs have been made, evaluating the effect on the results of the different mathematical models and the novel strategy that can be considered

Heuristic decision model for intelligent nuclear power systems design

International Nuclear Information System (INIS)

Nassersharif, B.; Portal, M.G.; Gaeta, M.J.

1989-01-01

The objective of this project was to investigate intelligent nuclear power systems design. A theoretical model of the design process has been developed. A fundamental process in this model is the heuristic decision making for design (i.e., selection of methods, components, materials, etc.). Rule-based expert systems do not provide the completeness that is necessary to generate good design. A new method, based on the fuzzy set theory, has been developed and is presented here. A feedwater system knowledge base (KB) was developed for a prototype software experiment to benchmark the theory

Multiscale Modeling in the Clinic: Drug Design and Development

Energy Technology Data Exchange (ETDEWEB)

Clancy, Colleen E.; An, Gary; Cannon, William R.; Liu, Yaling; May, Elebeoba E.; Ortoleva, Peter; Popel, Aleksander S.; Sluka, James P.; Su, Jing; Vicini, Paolo; Zhou, Xiaobo; Eckmann, David M.

2016-02-17

A wide range of length and time scales are relevant to pharmacology, especially in drug development, drug design and drug delivery. Therefore, multi-scale computational modeling and simulation methods and paradigms that advance the linkage of phenomena occurring at these multiple scales have become increasingly important. Multi-scale approaches present in silico opportunities to advance laboratory research to bedside clinical applications in pharmaceuticals research. This is achievable through the capability of modeling to reveal phenomena occurring across multiple spatial and temporal scales, which are not otherwise readily accessible to experimentation. The resultant models, when validated, are capable of making testable predictions to guide drug design and delivery. In this review we describe the goals, methods, and opportunities of multi-scale modeling in drug design and development. We demonstrate the impact of multiple scales of modeling in this field. We indicate the common mathematical techniques employed for multi-scale modeling approaches used in pharmacology and present several examples illustrating the current state-of-the-art regarding drug development for: Excitable Systems (Heart); Cancer (Metastasis and Differentiation); Cancer (Angiogenesis and Drug Targeting); Metabolic Disorders; and Inflammation and Sepsis. We conclude with a focus on barriers to successful clinical translation of drug development, drug design and drug delivery multi-scale models.

Towards a visual modeling approach to designing microelectromechanical system transducers

Science.gov (United States)

Dewey, Allen; Srinivasan, Vijay; Icoz, Evrim

1999-12-01

In this paper, we address initial design capture and system conceptualization of microelectromechanical system transducers based on visual modeling and design. Visual modeling frames the task of generating hardware description language (analog and digital) component models in a manner similar to the task of generating software programming language applications. A structured topological design strategy is employed, whereby microelectromechanical foundry cell libraries are utilized to facilitate the design process of exploring candidate cells (topologies), varying key aspects of the transduction for each topology, and determining which topology best satisfies design requirements. Coupled-energy microelectromechanical system characterizations at a circuit level of abstraction are presented that are based on branch constitutive relations and an overall system of simultaneous differential and algebraic equations. The resulting design methodology is called visual integrated-microelectromechanical VHDL-AMS interactive design (VHDL-AMS is visual hardware design language for analog and mixed signal).

PROPOSAL OF A MODEL MANAGEMENT TO SMALL DESIGN COMPANIES

Directory of Open Access Journals (Sweden)

Otávio José de OLIVEIRA

2008-11-01

Full Text Available The main purpose of this paper is the proposition of a management model specifically developed for small building design firms, aligned with their needs and particularities. The field research was conducted with a qualitative approach through the analysis of four case studies in small building design firms acting mainly in São Paulo City. The data collection was accomplished through semi-structured interviews, direct observation and analysis of documents. The proposed model includes guidance to the management of the core processes and activities of small building design firms, such as: organizational structure; strategic planning; planning and control of design process; costs management; sales management; information systems; human resources management; services added to the design; and performance evaluation. Key-words: design firms; design process; building construction.

Dual Value Creation and Business Model Design

DEFF Research Database (Denmark)

Turcan, Romeo V.

This ethnographic research explores the process of business model design in the context of an NGO internationalizing to an emerging market. It contributes to the business model literature by investigating how this NGO - targeting multiple key stakeholders - was experimenting (1) with value...

Automatic paper sliceform design from 3D solid models.

Science.gov (United States)

Le-Nguyen, Tuong-Vu; Low, Kok-Lim; Ruiz, Conrado; Le, Sang N

2013-11-01

A paper sliceform or lattice-style pop-up is a form of papercraft that uses two sets of parallel paper patches slotted together to make a foldable structure. The structure can be folded flat, as well as fully opened (popped-up) to make the two sets of patches orthogonal to each other. Automatic design of paper sliceforms is still not supported by existing computational models and remains a challenge. We propose novel geometric formulations of valid paper sliceform designs that consider the stability, flat-foldability and physical realizability of the designs. Based on a set of sufficient construction conditions, we also present an automatic algorithm for generating valid sliceform designs that closely depict the given 3D solid models. By approximating the input models using a set of generalized cylinders, our method significantly reduces the search space for stable and flat-foldable sliceforms. To ensure the physical realizability of the designs, the algorithm automatically generates slots or slits on the patches such that no two cycles embedded in two different patches are interlocking each other. This guarantees local pairwise assembility between patches, which is empirically shown to lead to global assembility. Our method has been demonstrated on a number of example models, and the output designs have been successfully made into real paper sliceforms.

Electrical design and control. Simulation platform to model, optimice and design windturbines; Elektrisk design og styring - simuleringsplatform til modellering, optimering og design af vindmoeller

Energy Technology Data Exchange (ETDEWEB)

Iov, F.; Timbus, A.V.; Hansen, A.D.; Soerensen, P.; Blaabjerg, F.

2004-03-01

This report is a general overview of the results obtained in the project 'Electrical Design and Control. Simulation Platform to Model, Optimize and Design Wind Turbines'. The motivation for this research project is the ever-increasing wind energy penetration into the power network. Therefore, the project has the main goal to create a model database in different simulation tools for a system optimization of the wind turbine systems. Using this model database a simultaneous optimization of the aerodynamic, mechanical, electrical and control systems over the whole range of wind speeds and grid characteristics can be achieved. The report is structured in six chapters. First, the background of this project and the main goals as well as the structure of the simulation platform is given. The main topologies for wind turbines, which have been taken into account during the project, are briefly presented. Then, the considered simulation tools narrely: HAWC, DIgSILENT, Saber and Matlab/Simulink have been used in this simulation platform are described. The focus here is on the modelling and simulation time scale aspects. The abilities of these tools are complementary and they can together cover all the modelling aspects of the wind turbines e.g. mechanical loads, power quality, switching, control and grid faults. However, other simulation packages e.g PSCAD/EMTDC can easily be added in the simulation platform. New models and new Control algorithms for wind turbine systems have been developed and tested in these tools. All these models are collected in dedicated libraries in Matlab/Simulink as well as in Saber. Some simulation results from the considered tools are presented for MW wind turbines. These simulation results focuses on fixed-speed and variable speed/pitch wind turbines. A good agreement with the real behaviour of these systems is obtained for each simulation tool. These models can easily be extended to model different kinds of wind turbines or large wind

Feature-based component model for design of embedded systems

Science.gov (United States)

Zha, Xuan Fang; Sriram, Ram D.

2004-11-01

An embedded system is a hybrid of hardware and software, which combines software's flexibility and hardware real-time performance. Embedded systems can be considered as assemblies of hardware and software components. An Open Embedded System Model (OESM) is currently being developed at NIST to provide a standard representation and exchange protocol for embedded systems and system-level design, simulation, and testing information. This paper proposes an approach to representing an embedded system feature-based model in OESM, i.e., Open Embedded System Feature Model (OESFM), addressing models of embedded system artifacts, embedded system components, embedded system features, and embedded system configuration/assembly. The approach provides an object-oriented UML (Unified Modeling Language) representation for the embedded system feature model and defines an extension to the NIST Core Product Model. The model provides a feature-based component framework allowing the designer to develop a virtual embedded system prototype through assembling virtual components. The framework not only provides a formal precise model of the embedded system prototype but also offers the possibility of designing variation of prototypes whose members are derived by changing certain virtual components with different features. A case study example is discussed to illustrate the embedded system model.

11th International Workshop in Model-Oriented Design and Analysis

CERN Document Server

Müller, Christine; Atkinson, Anthony

2016-01-01

This volume contains pioneering contributions to both the theory and practice of optimal experimental design. Topics include the optimality of designs in linear and nonlinear models, as well as designs for correlated observations and for sequential experimentation. There is an emphasis on applications to medicine, in particular, to the design of clinical trials. Scientists from Europe, the US, Asia, Australia and Africa contributed to this volume of papers from the 11th Workshop on Model Oriented Design and Analysis.

Electric market models, competitive model and alternative design

International Nuclear Information System (INIS)

Arnedillo, O.

2007-01-01

Almost ten years after the liberalization of the Spanish electric system, its market design has remained basically unchanged. Therefore, it is reasonable to consider whether the current model continues to be adequate or whether it should be changed. However, although the current model is far from the absolute optimum, it is suited to the current state of the Spanish system. Only some improvements, such as the reform of the capacity guarantee payment can be undertaken immediately. It will only be possible to undertake other improvements as distribution companies cover all of their electricity needs in forward contracts acquired through a competitive process. (Author)

Ground Vehicle System Integration (GVSI) and Design Optimization Model

National Research Council Canada - National Science Library

Horton, William

1996-01-01

This report documents the Ground Vehicle System Integration (GVSI) and Design Optimization Model GVSI is a top-level analysis tool designed to support engineering tradeoff studies and vehicle design optimization efforts...

Integrating acoustic analysis in the architectural design process using parametric modelling

DEFF Research Database (Denmark)

Peters, Brady

2011-01-01

This paper discusses how parametric modeling techniques can be used to provide architectural designers with a better understanding of the acoustic performance of their designs and provide acoustic engineers with models that can be analyzed using computational acoustic analysis software. Architects......, acoustic performance can inform the geometry and material logic of the design. In this way, the architectural design and the acoustic analysis model become linked....

Micromechatronics modeling, analysis, and design with Matlab

CERN Document Server

Giurgiutiu, Victor

2009-01-01

Focusing on recent developments in engineering science, enabling hardware, advanced technologies, and software, Micromechatronics: Modeling, Analysis, and Design with MATLAB®, Second Edition provides clear, comprehensive coverage of mechatronic and electromechanical systems. It applies cornerstone fundamentals to the design of electromechanical systems, covers emerging software and hardware, introduces the rigorous theory, examines the design of high-performance systems, and helps develop problem-solving skills. Along with more streamlined material, this edition adds many new sections to exist

Modeling in the quality by design environment: Regulatory requirements and recommendations for design space and control strategy appointment.

Science.gov (United States)

Djuris, Jelena; Djuric, Zorica

2017-11-30

Mathematical models can be used as an integral part of the quality by design (QbD) concept throughout the product lifecycle for variety of purposes, including appointment of the design space and control strategy, continual improvement and risk assessment. Examples of different mathematical modeling techniques (mechanistic, empirical and hybrid) in the pharmaceutical development and process monitoring or control are provided in the presented review. In the QbD context, mathematical models are predominantly used to support design space and/or control strategies. Considering their impact to the final product quality, models can be divided into the following categories: high, medium and low impact models. Although there are regulatory guidelines on the topic of modeling applications, review of QbD-based submission containing modeling elements revealed concerns regarding the scale-dependency of design spaces and verification of models predictions at commercial scale of manufacturing, especially regarding real-time release (RTR) models. Authors provide critical overview on the good modeling practices and introduce concepts of multiple-unit, adaptive and dynamic design space, multivariate specifications and methods for process uncertainty analysis. RTR specification with mathematical model and different approaches to multivariate statistical process control supporting process analytical technologies are also presented. Copyright © 2017 Elsevier B.V. All rights reserved.

Simulation models and designs for advanced Fischer-Tropsch technology

Energy Technology Data Exchange (ETDEWEB)

Choi, G.N.; Kramer, S.J.; Tam, S.S. [Bechtel Corp., San Francisco, CA (United States)

1995-12-31

Process designs and economics were developed for three grass-roots indirect Fischer-Tropsch coal liquefaction facilities. A baseline and an alternate upgrading design were developed for a mine-mouth plant located in southern Illinois using Illinois No. 6 coal, and one for a mine-mouth plane located in Wyoming using Power River Basin coal. The alternate design used close-coupled ZSM-5 reactors to upgrade the vapor stream leaving the Fischer-Tropsch reactor. ASPEN process simulation models were developed for all three designs. These results have been reported previously. In this study, the ASPEN process simulation model was enhanced to improve the vapor/liquid equilibrium calculations for the products leaving the slurry bed Fischer-Tropsch reactors. This significantly improved the predictions for the alternate ZSM-5 upgrading design. Another model was developed for the Wyoming coal case using ZSM-5 upgrading of the Fischer-Tropsch reactor vapors. To date, this is the best indirect coal liquefaction case. Sensitivity studies showed that additional cost reductions are possible.

Design and Implementation of Linux Access Control Model

Institute of Scientific and Technical Information of China (English)

Wei Xiaomeng; Wu Yongbin; Zhuo Jingchuan; Wang Jianyun; Haliqian Mayibula

2017-01-01

In this paper,the design and implementation of an access control model for Linux system are discussed in detail. The design is based on the RBAC model and combines with the inherent characteristics of the Linux system,and the support for the process and role transition is added.The core idea of the model is that the file is divided into different categories,and access authority of every category is distributed to several roles.Then,roles are assigned to users of the system,and the role of the user can be transited from one to another by running the executable file.

NUMERICAL MODEL APPLICATION IN ROWING SIMULATOR DESIGN

Directory of Open Access Journals (Sweden)

Petr Chmátal

2016-04-01

Full Text Available The aim of the research was to carry out a hydraulic design of rowing/sculling and paddling simulator. Nowadays there are two main approaches in the simulator design. The first one includes a static water with no artificial movement and counts on specially cut oars to provide the same resistance in the water. The second approach, on the other hand uses pumps or similar devices to force the water to circulate but both of the designs share many problems. Such problems are affecting already built facilities and can be summarized as unrealistic feeling, unwanted turbulent flow and bad velocity profile. Therefore, the goal was to design a new rowing simulator that would provide nature-like conditions for the racers and provide an unmatched experience. In order to accomplish this challenge, it was decided to use in-depth numerical modeling to solve the hydraulic problems. The general measures for the design were taken in accordance with space availability of the simulator ́s housing. The entire research was coordinated with other stages of the construction using BIM. The detailed geometry was designed using a numerical model in Ansys Fluent and parametric auto-optimization tools which led to minimum negative hydraulic phenomena and decreased investment and operational costs due to the decreased hydraulic losses in the system.

Specialty Payment Model Opportunities and Assessment: Oncology Model Design Report.

Science.gov (United States)

Huckfeldt, Peter J; Chan, Chris; Hirshman, Samuel; Kofner, Aaron; Liu, Jodi L; Mulcahy, Andrew W; Popescu, Ioana; Stevens, Clare; Timbie, Justin W; Hussey, Peter S

2015-07-15

This article describes research related to the design of a payment model for specialty oncology services for possible testing by the Center for Medicare and Medicaid Innovation at the Centers for Medicare & Medicaid Services (CMS). Cancer is a common and costly condition. Episode-based payment, which aims to create incentives for high-quality, low-cost care, has been identified as a promising alternative payment model for oncology care. Episode-based payment systems can provide flexibility to health care providers to select among the most effective and efficient treatment alternatives, including activities that are not currently reimbursed under Medicare payment policies. However, the model design also needs to ensure that high-quality care is delivered and that beneficial treatments are not withheld from patients. CMS asked MITRE and RAND to conduct analyses to inform design decisions related to an episode-based oncology model for Medicare beneficiaries undergoing chemotherapy treatment for cancer. In particular, this study focuses on analyses of Medicare claims data related to the definition of the initiation of an episode of chemotherapy, patterns of spending during and surrounding episodes of chemotherapy, and attribution of episodes of chemotherapy to physician practices. We found that the time between the primary cancer diagnosis and chemotherapy initiation varied widely across patients, ranging from one day to over seven years, with a median of 2.4 months. The average level of total monthly payments varied considerably across cancers, with the highest spending peak of $9,972 for lymphoma, and peaks of $3,109 for breast cancer and $2,135 for prostate cancer.

Experience economy meets business model design

DEFF Research Database (Denmark)

Gudiksen, Sune Klok; Smed, Søren Graakjær; Poulsen, Søren Bolvig

2012-01-01

Through the last decade the experience economy has found solid ground and manifested itself as a parameter where business and organizations can differentiate from competitors. The fundamental premise is the one found in Pine & Gilmores model from 1999 over 'the progression of economic value' where...... produced, designed or staged experience that gains the most profit or creates return of investment. It becomes more obvious that other parameters in the future can be a vital part of the experience economy and one of these is business model innovation. Business model innovation is about continuous...

Modeling and Simulation for Mission Operations Work System Design

Science.gov (United States)

Sierhuis, Maarten; Clancey, William J.; Seah, Chin; Trimble, Jay P.; Sims, Michael H.

2003-01-01

Work System analysis and design is complex and non-deterministic. In this paper we describe Brahms, a multiagent modeling and simulation environment for designing complex interactions in human-machine systems. Brahms was originally conceived as a business process design tool that simulates work practices, including social systems of work. We describe our modeling and simulation method for mission operations work systems design, based on a research case study in which we used Brahms to design mission operations for a proposed discovery mission to the Moon. We then describe the results of an actual method application project-the Brahms Mars Exploration Rover. Space mission operations are similar to operations of traditional organizations; we show that the application of Brahms for space mission operations design is relevant and transferable to other types of business processes in organizations.

Modeling the Structure and Complexity of Engineering Routine Design Problems

NARCIS (Netherlands)

Jauregui Becker, Juan Manuel; Wits, Wessel Willems; van Houten, Frederikus J.A.M.

2011-01-01

This paper proposes a model to structure routine design problems as well as a model of its design complexity. The idea is that having a proper model of the structure of such problems enables understanding its complexity, and likewise, a proper understanding of its complexity enables the development

Prevention through Design Adoption Readiness Model (PtD ARM): An integrated conceptual model.

Science.gov (United States)

Weidman, Justin; Dickerson, Deborah E; Koebel, Charles T

2015-01-01

Prevention through Design (PtD), eliminating hazards at the design-stage of tools and systems, is the optimal method of mitigating occupational health and safety risks. A recent National Institute of Safety and Health initiative has established a goal to increase adoption of PtD innovation in industry. The construction industry has traditionally lagged behind other sectors in the adoption of innovation, in general; and of safety and health prevention innovation, in particular. Therefore, as a first step toward improving adoption trends in this sector, a conceptual model was developed to describe the parameters and causal relationships that influence and predict construction stakeholder "adoption readiness" for PtD technology innovation. This model was built upon three well-established theoretical frameworks: the Health Belief Model, the Diffusion of Innovation Model, and the Technology Acceptance Model. Earp and Ennett's model development methodology was employed to build a depiction of the key constructs and directionality and magnitude of relationships among them. Key constructs were identified from the literature associated with the three theoretical frameworks, with special emphasis given to studies related to construction or OHS technology adoption. A conceptual model is presented. Recommendations for future research are described and include confirmatory structural equation modeling of model parameters and relationships, additional descriptive investigation of barriers to adoption in some trade sectors, and design and evaluation of an intervention strategy.

A Model-driven Framework for Educational Game Design

Directory of Open Access Journals (Sweden)

Bill Roungas

2016-09-01

Full Text Available Educational games are a class of serious games whose main purpose is to teach some subject to their players. Despite the many existing design frameworks, these games are too often created in an ad-hoc manner, and typically without the use of a game design document (GDD. We argue that a reason for this phenomenon is that current ways to structure, create and update GDDs do not increase the value of the artifact in the design and development process. As a solution, we propose a model-driven, web-based knowledge management environment that supports game designers in the creation of a GDD that accounts for and relates educational and entertainment game elements. The foundation of our approach is our devised conceptual model for educational games, which also defines the structure of the design environment. We present promising results from an evaluation of our environment with eight experts in serious games.

Design of disturbances control model at automotive company

Science.gov (United States)

Marie, I. A.; Sari, D. K.; Astuti, P.; Teorema, M.

2017-12-01

The discussion was conducted at PT. XYZ which produces automotive components and motorcycle products. The company produced X123 type cylinder head which is a motor vehicle forming component. The disturbances in the production system has affected the company performance in achieving the target of Key Performance Indicator (KPI). Currently, the determination of the percentage of safety stock of cylinder head products is not in accordance to the control limits set by the company (60% - 80%), and tends to exceed the control limits that cause increasing the inventory wastage in the company. This study aims to identify the production system disturbances that occurs in the production process of manufacturing components of X123 type cylinder head products and design the control model of disturbance to obtain control action and determine the safety stock policy in accordance with the needs of the company. The design stage has been done based on the Disturbance Control Model which already existing and customized with the company need in controlling the production system disturbances at the company. The design of the disturbances control model consists of sub-model of the risk level of the disturbance, sub-model of action status, sub-model action control of the disturbance, and sub-model of determining the safety stock. The model can assist the automotive company in taking the decision to perform the disturbances control action in production system cylinder head while controlling the percentage of the safety stock.

Applying Probabilistic Decision Models to Clinical Trial Design

Science.gov (United States)

Smith, Wade P; Phillips, Mark H

2018-01-01

Clinical trial design most often focuses on a single or several related outcomes with corresponding calculations of statistical power. We consider a clinical trial to be a decision problem, often with competing outcomes. Using a current controversy in the treatment of HPV-positive head and neck cancer, we apply several different probabilistic methods to help define the range of outcomes given different possible trial designs. Our model incorporates the uncertainties in the disease process and treatment response and the inhomogeneities in the patient population. Instead of expected utility, we have used a Markov model to calculate quality adjusted life expectancy as a maximization objective. Monte Carlo simulations over realistic ranges of parameters are used to explore different trial scenarios given the possible ranges of parameters. This modeling approach can be used to better inform the initial trial design so that it will more likely achieve clinical relevance.

PHARAO laser source flight model: Design and performances

Energy Technology Data Exchange (ETDEWEB)

Lévèque, T., E-mail: thomas.leveque@cnes.fr; Faure, B.; Esnault, F. X.; Delaroche, C.; Massonnet, D.; Grosjean, O.; Buffe, F.; Torresi, P. [Centre National d’Etudes Spatiales, 18 avenue Edouard Belin, 31400 Toulouse (France); Bomer, T.; Pichon, A.; Béraud, P.; Lelay, J. P.; Thomin, S. [Sodern, 20 Avenue Descartes, 94451 Limeil-Brévannes (France); Laurent, Ph. [LNE-SYRTE, CNRS, UPMC, Observatoire de Paris, 61 avenue de l’Observatoire, 75014 Paris (France)

2015-03-15

In this paper, we describe the design and the main performances of the PHARAO laser source flight model. PHARAO is a laser cooled cesium clock specially designed for operation in space and the laser source is one of the main sub-systems. The flight model presented in this work is the first remote-controlled laser system designed for spaceborne cold atom manipulation. The main challenges arise from mechanical compatibility with space constraints, which impose a high level of compactness, a low electric power consumption, a wide range of operating temperature, and a vacuum environment. We describe the main functions of the laser source and give an overview of the main technologies developed for this instrument. We present some results of the qualification process. The characteristics of the laser source flight model, and their impact on the clock performances, have been verified in operational conditions.

Code Development for Control Design Applications: Phase I: Structural Modeling

International Nuclear Information System (INIS)

Bir, G. S.; Robinson, M.

1998-01-01

The design of integrated controls for a complex system like a wind turbine relies on a system model in an explicit format, e.g., state-space format. Current wind turbine codes focus on turbine simulation and not on system characterization, which is desired for controls design as well as applications like operating turbine model analysis, optimal design, and aeroelastic stability analysis. This paper reviews structural modeling that comprises three major steps: formation of component equations, assembly into system equations, and linearization

Elektrisk Design og Styring. Simulation Platform to Model, Optimize and Design Wind Turbines

DEFF Research Database (Denmark)

Iov, Florin; Hansen, A. D.; Soerensen, P.

This report is a general overview of the results obtained in the project ?Electrical Design and Control. Simulation Platform to Model, Optimize and Design Wind Turbines?. The report is structured in six chapters. First, the background of this project and the main goals as well as the structure...... of the simulation platform is given. The main topologies for wind turbines, which have been taken into account during the project, are briefly presented. Then, the considered simulation tools namely: HAWC, DIgSILENT, Saber and Matlab/Simulink have been used in this simulation platform are described. The focus here...... is on the modelling and simulation time scale aspects. The abilities of these tools are complementary and they can together cover all the modelling aspects of the wind turbines e.g. mechanical loads, power quality, switching, control and grid faults. New models and new control algorithms for wind turbine systems have...

Multi-objective optimization of generalized reliability design problems using feature models-A concept for early design stages

International Nuclear Information System (INIS)

Limbourg, Philipp; Kochs, Hans-Dieter

2008-01-01

Reliability optimization problems such as the redundancy allocation problem (RAP) have been of considerable interest in the past. However, due to the restrictions of the design space formulation, they may not be applicable in all practical design problems. A method with high modelling freedom for rapid design screening is desirable, especially in early design stages. This work presents a novel approach to reliability optimization. Feature modelling, a specification method originating from software engineering, is applied for the fast specification and enumeration of complex design spaces. It is shown how feature models can not only describe arbitrary RAPs but also much more complex design problems. The design screening is accomplished by a multi-objective evolutionary algorithm for probabilistic objectives. Comparing averages or medians may hide the true characteristics of this distributions. Therefore the algorithm uses solely the probability of a system dominating another to achieve the Pareto optimal set. We illustrate the approach by specifying a RAP and a more complex design space and screening them with the evolutionary algorithm

Spin-Tunnel Investigation of a 1/20-Scale Model of the Northrop F-5E Airplane

Science.gov (United States)

Scher, Stanley H.; White, William L.

1977-01-01

An investigation has been conducted in the Langley spin tunnel to determine the spin and recovery characteristics of a 1/20-scale model of the Northrop F-5E airplane. The investigation included erect and inverted spins, a range of center-of- gravity locations and moments of inertia, symmetric and asymmetric store loadings, and a determination of the parachute size required for emergency spin recovery. The effects of increased elevator trailing-edge-up deflections, of leading-edge and trailing-edge flap deflections, and of simulating the geometry of large external stores were also determined.

Should students design or interact with models? Using the Bifocal Modelling Framework to investigate model construction in high school science

Science.gov (United States)

Fuhrmann, Tamar; Schneider, Bertrand; Blikstein, Paulo

2018-05-01

The Bifocal Modelling Framework (BMF) is an approach for science learning which links students' physical experimentation with computer modelling in real time, focusing on the comparison of the two media. In this paper, we explore how a Bifocal Modelling implementation supported learning outcomes related to both content and metamodeling knowledge, focusing on the role of designing models. Our study consisted of three conditions implemented with a total of 69 9th grade high-school students. The first and second classes were assigned two implementation modes of BMF: with and without a model design module. The third condition, employed as a control, consisted of a class that received instruction in the school's traditional approach. Our results indicate that students participating in both BMF implementations demonstrated improved content knowledge and a better understanding of metamodeling. However, only the 'BMF-with-design' group improved significantly in both content and metamodeling knowledge. Our qualitative analyses indicate that both BMF groups designed detailed models that included scientific explanations. However only students who engaged in the model design component: (1) completed a detailed model displaying molecular interaction; and (2) developed a critical perspective about models. We discuss the implications of those results for teaching scientific science concepts and metamodeling knowledge.

Intelligent design of mechanical parameters of the joint in vehicle body concept design model

Science.gov (United States)

Hou, Wen-bin; Zhang, Hong-zhe; Hou, Da-jun; Hu, Ping

2013-05-01

In order to estimate the mechanical properties of the overall structure of the body accurately and quickly in conceptual design phase of the body, the beam and shell mixing elements was used to build simplified finite element model of the body. Through the BP neural network algorithm, the parameters of the mechanical property of joints element which had more affection on calculation accuracy were calculated and the joint finite element model based on the parameters was also constructed. The case shown that the method can improve the accuracy of the vehicle simulation results, while not too many design details were needed, which was fit to the demand in the vehicle body conceptual design phase.

Free-Spinning-Tunnel Investigation of a 0.034-Scale Model of the Production Version of the Chance Vought F7U-3 Airplane, TED No. NACA AD 3103

Science.gov (United States)

Klinar, Walter J.; Healy, Frederick M.

1955-01-01

An investigation of a 0.034-scale model of the production version of the Chance Vought F7U-3 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The inverted and erect spin and recovery characteristics of the model were determined for the combat loading with the model in the clean condition and the effect of extending slats was investigated. A brief investigation of pilot ejection was also performed. The results indicate that the inverted spin-recovery characteristics of the airplane will be satisfactory by full rudder reversal. If the rudders can only be neutralized because of high pedal forces in the inverted spins, satisfactory recovery will be obtained if the auxiliary rudders can be moved to neutral or against the spin provided the stick is held full forward. Optimum control technique for satisfactory recovery from erect spins will be full rudder reversal in conjunction with aileron movement to full with the spin (stick right in a right spin). Extension of the slats will have a slightly adverse effect on recoveries from (1 inverted spins but will have a favorable effect on recoveries from erect spins. The results of brief tests indicate that if a pilot is ejected during a spin while a spin-recovery parachute is extended and fully inflated, he will probably clear the tail parachute.

A dual model approach to ground water recovery trench design

International Nuclear Information System (INIS)

Clodfelter, C.L.; Crouch, M.S.

1992-01-01

The design of trenches for contaminated ground water recovery must consider several variables. This paper presents a dual-model approach for effectively recovering contaminated ground water migrating toward a trench by advection. The approach involves an analytical model to determine the vertical influence of the trench and a numerical flow model to determine the capture zone within the trench and the surrounding aquifer. The analytical model is utilized by varying trench dimensions and head values to design a trench which meets the remediation criteria. The numerical flow model is utilized to select the type of backfill and location of sumps within the trench. The dual-model approach can be used to design a recovery trench which effectively captures advective migration of contaminants in the vertical and horizontal planes

Geometric modeling for computer aided design

Science.gov (United States)

Schwing, James L.; Olariu, Stephen

1995-01-01

The primary goal of this grant has been the design and implementation of software to be used in the conceptual design of aerospace vehicles particularly focused on the elements of geometric design, graphical user interfaces, and the interaction of the multitude of software typically used in this engineering environment. This has resulted in the development of several analysis packages and design studies. These include two major software systems currently used in the conceptual level design of aerospace vehicles. These tools are SMART, the Solid Modeling Aerospace Research Tool, and EASIE, the Environment for Software Integration and Execution. Additional software tools were designed and implemented to address the needs of the engineer working in the conceptual design environment. SMART provides conceptual designers with a rapid prototyping capability and several engineering analysis capabilities. In addition, SMART has a carefully engineered user interface that makes it easy to learn and use. Finally, a number of specialty characteristics have been built into SMART which allow it to be used efficiently as a front end geometry processor for other analysis packages. EASIE provides a set of interactive utilities that simplify the task of building and executing computer aided design systems consisting of diverse, stand-alone, analysis codes. Resulting in a streamlining of the exchange of data between programs reducing errors and improving the efficiency. EASIE provides both a methodology and a collection of software tools to ease the task of coordinating engineering design and analysis codes.

Planetary Suit Hip Bearing Model for Predicting Design vs. Performance

Science.gov (United States)

Cowley, Matthew S.; Margerum, Sarah; Harvil, Lauren; Rajulu, Sudhakar

2011-01-01

Designing a planetary suit is very complex and often requires difficult trade-offs between performance, cost, mass, and system complexity. In order to verifying that new suit designs meet requirements, full prototypes must eventually be built and tested with human subjects. Using computer models early in the design phase of new hardware development can be advantageous, allowing virtual prototyping to take place. Having easily modifiable models of the suit hard sections may reduce the time it takes to make changes to the hardware designs and then to understand their impact on suit and human performance. A virtual design environment gives designers the ability to think outside the box and exhaust design possibilities before building and testing physical prototypes with human subjects. Reductions in prototyping and testing may eventually reduce development costs. This study is an attempt to develop computer models of the hard components of the suit with known physical characteristics, supplemented with human subject performance data. Objectives: The primary objective was to develop an articulating solid model of the Mark III hip bearings to be used for evaluating suit design performance of the hip joint. Methods: Solid models of a planetary prototype (Mark III) suit s hip bearings and brief section were reverse-engineered from the prototype. The performance of the models was then compared by evaluating the mobility performance differences between the nominal hardware configuration and hardware modifications. This was accomplished by gathering data from specific suited tasks. Subjects performed maximum flexion and abduction tasks while in a nominal suit bearing configuration and in three off-nominal configurations. Performance data for the hip were recorded using state-of-the-art motion capture technology. Results: The results demonstrate that solid models of planetary suit hard segments for use as a performance design tool is feasible. From a general trend perspective

A product-model supporting coupling's management during microproduct design

DEFF Research Database (Denmark)

Museau, Matthieu; De Grave, Arnaud; Masclet, Cedric

2009-01-01

Microproducts show specificities compared to macroproducts and their design processes differ. Nowadays, existing design tools manage microproduct specificities too late during the design process, only after the first product representation is available. This article presents a product-model able...

Designing for Learning and Play - The Smiley Model as Framework

DEFF Research Database (Denmark)

Weitze, Charlotte Lærke

2016-01-01

digital games. The Smiley Model inspired and provided a scaffold or a heuristic for the overall gamified learning design –- as well as for the students’ learning game design processes when creating small games turning the learning situation into an engaging experience. The audience for the experiments......This paper presents a framework for designing engaging learning experiences in games – the Smiley Model. In this Design-Based Research project, student-game-designers were learning inside a gamified learning design - while designing and implementing learning goals from curriculum into the small...... was adult upper secondary general students as well as 7th grade primary school students. The intention with this article is to inspire future learning designers that would like to experiment with integrating learning and play....

Model-based design and optimization of vanadium redox flow batteries

Energy Technology Data Exchange (ETDEWEB)

Koenig, Sebastian

2017-07-19

This work targets on increasing the efficiency of the Vanadium Redox Flow Battery (VRFB) using a model-based approach. First, a detailed instruction for setting up a VRFB model on a system level is given. Modelling of open-circuit-voltage, ohmic overpotential, concentration overpotential, Vanadium crossover, shunt currents as well as pump power demand is presented. All sub-models are illustrated using numerical examples. Using experimental data from three battery manufacturers, the voltage model validated. The identified deviations reveal deficiencies in the literature model. By correctly deriving the mass transfer coefficients and adapting the effective electrode area, these deficiencies are eliminated. The validated battery model is then deployed in an extensive design study. By varying the electrode area between 1000 and 4000 cm{sup 2} and varying the design of the electrolyte supply channel, twenty-four different cell designs are created using finite element analysis. These designs are subsequently simulated in 40-cell stacks deployed in systems with a single stack and systems with a three-stack string. Using the simulation results, the impact of different design parameters on different loss mechanisms is investigated. While operating the VRFB, the electrolyte flow rate is the most important operational parameter. A novel, model-based optimization strategy is presented and compared to established flow rate control strategies. Further, a voltage controller is introduced which delays the violation of cell voltage limits by controlling the flow rate as long as the pump capacity is not fully exploited.

Model-based design and optimization of vanadium redox flow batteries

International Nuclear Information System (INIS)

Koenig, Sebastian

2017-01-01

This work targets on increasing the efficiency of the Vanadium Redox Flow Battery (VRFB) using a model-based approach. First, a detailed instruction for setting up a VRFB model on a system level is given. Modelling of open-circuit-voltage, ohmic overpotential, concentration overpotential, Vanadium crossover, shunt currents as well as pump power demand is presented. All sub-models are illustrated using numerical examples. Using experimental data from three battery manufacturers, the voltage model validated. The identified deviations reveal deficiencies in the literature model. By correctly deriving the mass transfer coefficients and adapting the effective electrode area, these deficiencies are eliminated. The validated battery model is then deployed in an extensive design study. By varying the electrode area between 1000 and 4000 cm 2 and varying the design of the electrolyte supply channel, twenty-four different cell designs are created using finite element analysis. These designs are subsequently simulated in 40-cell stacks deployed in systems with a single stack and systems with a three-stack string. Using the simulation results, the impact of different design parameters on different loss mechanisms is investigated. While operating the VRFB, the electrolyte flow rate is the most important operational parameter. A novel, model-based optimization strategy is presented and compared to established flow rate control strategies. Further, a voltage controller is introduced which delays the violation of cell voltage limits by controlling the flow rate as long as the pump capacity is not fully exploited.

Designing the model for evaluating business quality in Croatia

Directory of Open Access Journals (Sweden)

Ana Ježovita

2015-01-01

Full Text Available The main objective of the paper includes designing a model for evaluating the financial quality of business operations. In that context, for the paper purposes, the financial quality of business operations is defined as an ability to achieve adequate value of individual financial ratios for financial position and performance evaluation. The objective of the model is to obtain comprehensive conclusion about the financial quality of business operation using only value of the function. Data used for designing the model is limited to financial data available from the annual balance sheet and income statement. Those limitations offer the opportunity for all sizes of companies from the non-financial business economy sector to use the designed model for evaluation purposes. Statistical methods used for designing the model are multivariate discriminant analysis and logistic regression. Discriminant analysis resulted in the function which includes five individual financial ratios with the best discriminant power. Respecting the results obtained in the classification matrix with classification accuracy of 95.92% by the original sample, or accuracy of 96.06% for the independent sample, it can be concluded that it is possible to evaluate the financial quality of business operations of companies in Croatia by using the model composed of individual financial ratios. Conducted logistic regression confirms the results obtained using discriminant analysis.

Analysis and Evaluation of Statistical Models for Integrated Circuits Design

Directory of Open Access Journals (Sweden)

Sáenz-Noval J.J.

2011-10-01

Full Text Available Statistical models for integrated circuits (IC allow us to estimate the percentage of acceptable devices in the batch before fabrication. Actually, Pelgrom is the statistical model most accepted in the industry; however it was derived from a micrometer technology, which does not guarantee reliability in nanometric manufacturing processes. This work considers three of the most relevant statistical models in the industry and evaluates their limitations and advantages in analog design, so that the designer has a better criterion to make a choice. Moreover, it shows how several statistical models can be used for each one of the stages and design purposes.

Ligand modeling and design

Energy Technology Data Exchange (ETDEWEB)

Hay, B.P. [Pacific Northwest National Lab., Richland, WA (United States)

1997-10-01

The purpose of this work is to develop and implement a molecular design basis for selecting organic ligands that would be used in the cost-effective removal of specific radionuclides from nuclear waste streams. Organic ligands with metal ion specificity are critical components in the development of solvent extraction and ion exchange processes that are highly selective for targeted radionuclides. The traditional approach to the development of such ligands involves lengthy programs of organic synthesis and testing, which in the absence of reliable methods for screening compounds before synthesis, results in wasted research effort. The author`s approach breaks down and simplifies this costly process with the aid of computer-based molecular modeling techniques. Commercial software for organic molecular modeling is being configured to examine the interactions between organic ligands and metal ions, yielding an inexpensive, commercially or readily available computational tool that can be used to predict the structures and energies of ligand-metal complexes. Users will be able to correlate the large body of existing experimental data on structure, solution binding affinity, and metal ion selectivity to develop structural design criteria. These criteria will provide a basis for selecting ligands that can be implemented in separations technologies through collaboration with other DOE national laboratories and private industry. The initial focus will be to select ether-based ligands that can be applied to the recovery and concentration of the alkali and alkaline earth metal ions including cesium, strontium, and radium.

Pressurized water reactor system model for control system design and analysis

International Nuclear Information System (INIS)

Cooper, K.F.; Cain, J.T.

1975-01-01

Satisfactory operation of present generation Pressurized Water Reactor (PWR) Nuclear Power systems requires that several independent and interactive control systems be designed. Since it is not practical to use an actual PWR system as a design tool, a mathematical model of the system must be developed as a design and analysis tool. The model presented has been developed to be used as an aid in applying optimal control theory to design and implement new control systems for PWR plants. To be applicable, the model developed must represent the PWR system in its normal operating range. For safety analysis the operating conditions of the system are usually abnormal and, therefore, the system modeling requirements are different from those for control system design and analysis

Model-based design of self-Adapting networked signal processing systems

NARCIS (Netherlands)

Oliveira Filho, J.A. de; Papp, Z.; Djapic, R.; Oostveen, J.C.

2013-01-01

The paper describes a model based approach for architecture design of runtime reconfigurable, large-scale, networked signal processing applications. A graph based modeling formalism is introduced to describe all relevant aspects of the design (functional, concurrency, hardware, communication,

Model based design of biochemical micro-reactors

Directory of Open Access Journals (Sweden)

Tobias eElbinger

2016-02-01

Full Text Available Mathematical modelling of biochemical pathways is an important resource in Synthetic Biology, as the predictive power of simulating synthetic pathways represents an important step in the design of synthetic metabolons. In this paper, we are concerned with the mathematical modeling, simulation and optimization of metabolic processes in biochemical micro-reactors able to carry out enzymatic reactions and to exchange metabolites with their surrounding medium. The results of the reported modeling approach are incorporated in the design of the first micro-reactor prototypes that are under construction. These microreactors consist of compartments separated by membranes carrying specific transporters for the input of substrates and export of products. Inside the compartments multi-enzyme complexes assembled on nano-beads by peptide adapters are used to carry out metabolic reactions.The spatially resolved mathematical model describing the ongoing processes consists of a system of diffusion equations together with boundary and initial conditions. The boundary conditions model the exchange of metabolites with the neighboring compartments and the reactions at the surface of the nano-beads carrying the multi-enzyme complexes. Efficient and accurate approaches for numerical simulation of the mathematical model and for optimal design of the micro-reactor are developed. As a proof-of-concept scenario, a synthetic pathway for the conversion of sucrose to glucose-6-phosphate (G6P was chosen. In this context, the mathematical model is employed to compute the spatio-temporal distributions of the metabolite concentrations, as well as application relevant quantities like the outflow rate of G6P. These computations are performed for different scenarios, where the number of beads as well as their loading capacity are varied. The computed metabolite distributions show spatial patterns which differ for different experimental arrangements. Furthermore, the total output

Design for unusual environment (space). Complementary use of modelling and testing phases

International Nuclear Information System (INIS)

Cambiaghi, Danilo; Cambiaghi, Andrea

2004-01-01

Designing for space requires a great imagination effort from the designer. He must perceive that the stresses experimented by the facilities he is designing will be quite different in space (during the mission), in launch phase and on ground (before launch handling phase), and he must design for all such environmental conditions. Furthermore he must design for mechanical and thermal environment, which often lead to conflicting needs. Virtual models may help very much in balancing the conflicting requirements, but models must be validated to be reliable. Test phase help validating the models, but may overstress the items. The aim of the designer is to reach an efficient and safe design through a balanced use of creativity, modelling and testing

An Intelligent System for Modelling, Design and Analysis of Chemical Processes

DEFF Research Database (Denmark)

Gani, Rafiqul

ICAS, Integrated Computer Aided System, is a software that consists of a number of intelligent tools, which are very suitable, among others, for computer aided modelling, sustainable design of chemical and biochemical processes, and design-analysis of product-process monitoring systems. Each...... the computer aided modelling tool will illustrate how to generate a desired process model, how to analyze the model equations, how to extract data and identify the model and make it ready for various types of application. In sustainable process design, the example will highlight the issue of integration...

Designing a Process for Tracking Business Model Change

DEFF Research Database (Denmark)

Groskovs, Sergejs

The paper has adopted a design science research approach to design and verify with key stakeholders a fundamental management process of revising KPIs (key performance indicators), including those indicators that are related to business model change. The paper proposes a general guide for such pro......The paper has adopted a design science research approach to design and verify with key stakeholders a fundamental management process of revising KPIs (key performance indicators), including those indicators that are related to business model change. The paper proposes a general guide...... for such process design, which is applicable in similar settings, i.e. other multi-subsidiary global firms operating in dynamic industries. The management of the focal case uses a set of KPIs to track performance and thus to allow for bringing about strategic and tactical changes, including the initiatives...... by establishing new KPIs on an ongoing basis together with the business units on the ground, and is thus of key importance to strategic management of the firm. The paper concludes with a discussion of its methodological compliance to design science research guidelines and revisits the literature in process...

Design of spatial experiments: Model fitting and prediction

Energy Technology Data Exchange (ETDEWEB)

Fedorov, V.V.

1996-03-01

The main objective of the paper is to describe and develop model oriented methods and algorithms for the design of spatial experiments. Unlike many other publications in this area, the approach proposed here is essentially based on the ideas of convex design theory.

Property Modelling and Databases in Product-Process Design

DEFF Research Database (Denmark)

Gani, Rafiqul; Sansonetti, Sascha

of the PC-SAFT is used. The developed database and property prediction models have been combined into a properties-software that allows different product-process design related applications. The presentation will also briefly highlight applications of the software for virtual product-process design...

Sustainable Business Models through Service Design

NARCIS (Netherlands)

Prendeville, S.M.; Bocken, N.M.P.

2017-01-01

In the face of growing sustainability challenges, pressure on businesses to decouple environmental impacts from growth is mounting. New sustainable business models can be a systemic driver for change in industry and the wider business innovation literature suggests that strategic design approaches

The backbone of a City Information Model (CIM) : Implementing a spatial data model for urban design

NARCIS (Netherlands)

Gil, J.A.; Almeida, J.; Duarte, J.P.

2011-01-01

We have been witnessing an increased interest in a more holistic approach to urban design practice and education. In this paper we present a spatial data model for urban design that proposes the combination of urban environment feature classes with design process feature classes. This data model is

Designing experiments and analyzing data a model comparison perspective

CERN Document Server

Maxwell, Scott E

2013-01-01

Through this book's unique model comparison approach, students and researchers are introduced to a set of fundamental principles for analyzing data. After seeing how these principles can be applied in simple designs, students are shown how these same principles also apply in more complicated designs. Drs. Maxwell and Delaney believe that the model comparison approach better prepares students to understand the logic behind a general strategy of data analysis appropriate for various designs; and builds a stronger foundation, which allows for the introduction of more complex topics omitt

A systematic composite service design modeling method using graph-based theory.

Science.gov (United States)

Elhag, Arafat Abdulgader Mohammed; Mohamad, Radziah; Aziz, Muhammad Waqar; Zeshan, Furkh

2015-01-01

The composite service design modeling is an essential process of the service-oriented software development life cycle, where the candidate services, composite services, operations and their dependencies are required to be identified and specified before their design. However, a systematic service-oriented design modeling method for composite services is still in its infancy as most of the existing approaches provide the modeling of atomic services only. For these reasons, a new method (ComSDM) is proposed in this work for modeling the concept of service-oriented design to increase the reusability and decrease the complexity of system while keeping the service composition considerations in mind. Furthermore, the ComSDM method provides the mathematical representation of the components of service-oriented design using the graph-based theoryto facilitate the design quality measurement. To demonstrate that the ComSDM method is also suitable for composite service design modeling of distributed embedded real-time systems along with enterprise software development, it is implemented in the case study of a smart home. The results of the case study not only check the applicability of ComSDM, but can also be used to validate the complexity and reusability of ComSDM. This also guides the future research towards the design quality measurement such as using the ComSDM method to measure the quality of composite service design in service-oriented software system.

Models and Modelling Tools for Chemical Product and Process Design

DEFF Research Database (Denmark)

Gani, Rafiqul

2016-01-01

The design, development and reliability of a chemical product and the process to manufacture it, need to be consistent with the end-use characteristics of the desired product. One of the common ways to match the desired product-process characteristics is through trial and error based experiments......-based framework is that in the design, development and/or manufacturing of a chemical product-process, the knowledge of the applied phenomena together with the product-process design details can be provided with diverse degrees of abstractions and details. This would allow the experimental resources...... to be employed for validation and fine-tuning of the solutions from the model-based framework, thereby, removing the need for trial and error experimental steps. Also, questions related to economic feasibility, operability and sustainability, among others, can be considered in the early stages of design. However...

An analysis of the benefits of ethnography design methods for product modelling

Science.gov (United States)

Butlewski, M.; Misztal, A.; Belu, N.

2016-08-01

The essence of modelling is to reflect the studied piece of reality in such a way that best describes the selected elements of the designed system. A model is used in design to optimize the structure and parameters of the constructed object and is a tool for assessing the quality of construction, eliminating weak links and ensuring adequate safety components. In view of the aim of modelling, it can be divided into functional modelling, showing the complexity of the object, and reliability modelling, specifying its states at variable threshold values. In design, modelling allows for significant savings in resources that would otherwise be spent because of problems appearing at the prototype stage, but also during production or in the course of using the product. In the practice of ergonomic design many problems could be avoided if early enough in the design process the values of parameters and their relations would be taken into account through modelling. On the other hand, the modelling process can be costly and time-consuming to carry out, and against the currently pervasive lean production it is a highly undesirable factor. Therefore, the modelling process should be supported with the use of appropriate cognitive techniques namely ethnography design, which would determine inadequacies of existing models as well as indicate the equivalent conditions for modelling. The justification of the use of this technique results both from the possibility of providing additional information, as well as the opportunity to “test” the phenomena affecting the design process. Ergonomic modelling tests developed solutions towards their adaptation to users’ anthropometric, biomechanical and psychomotor characteristics, as well as behaviour patterns. However, knowledge of the latter and achieving a sufficient ergonomic and functional quality of proposed solutions often requires the use of the ethnography design approach. The aim of this article is to test the practical

Practical Findings from Applying the PSD Model for Evaluating Software Design Specifications

Science.gov (United States)

Räisänen, Teppo; Lehto, Tuomas; Oinas-Kukkonen, Harri

This paper presents practical findings from applying the PSD model to evaluating the support for persuasive features in software design specifications for a mobile Internet device. On the one hand, our experiences suggest that the PSD model fits relatively well for evaluating design specifications. On the other hand, the model would benefit from more specific heuristics for evaluating each technique to avoid unnecessary subjectivity. Better distinction between the design principles in the social support category would also make the model easier to use. Practitioners who have no theoretical background can apply the PSD model to increase the persuasiveness of the systems they design. The greatest benefit of the PSD model for researchers designing new systems may be achieved when it is applied together with a sound theory, such as the Elaboration Likelihood Model. Using the ELM together with the PSD model, one may increase the chances for attitude change.

On Optimal Input Design and Model Selection for Communication Channels

Energy Technology Data Exchange (ETDEWEB)

Li, Yanyan [ORNL; Djouadi, Seddik M [ORNL; Olama, Mohammed M [ORNL

2013-01-01

In this paper, the optimal model (structure) selection and input design which minimize the worst case identification error for communication systems are provided. The problem is formulated using metric complexity theory in a Hilbert space setting. It is pointed out that model selection and input design can be handled independently. Kolmogorov n-width is used to characterize the representation error introduced by model selection, while Gel fand and Time n-widths are used to represent the inherent error introduced by input design. After the model is selected, an optimal input which minimizes the worst case identification error is shown to exist. In particular, it is proven that the optimal model for reducing the representation error is a Finite Impulse Response (FIR) model, and the optimal input is an impulse at the start of the observation interval. FIR models are widely popular in communication systems, such as, in Orthogonal Frequency Division Multiplexing (OFDM) systems.

76 FR 45077 - Endangered and Threatened Wildlife and Plants; Designation of Critical Habitat for Ipomopsis...

Science.gov (United States)

2011-07-27

...: (1) Over most land, there will be warmer and fewer cold days and nights, and warmer and more frequent hot days and nights; (2) areas affected by drought will increase; and (3) the frequency of warm spells... oil shale cliffs of the Parachute Creek Member and the Lower Part of the Green River Formation at...

Design-based modeling of magnetically actuated soft diaphragm materials

Science.gov (United States)

Jayaneththi, V. R.; Aw, K. C.; McDaid, A. J.

2018-04-01

Magnetic polymer composites (MPC) have shown promise for emerging biomedical applications such as lab-on-a-chip and implantable drug delivery. These soft material actuators are capable of fast response, large deformation and wireless actuation. Existing MPC modeling approaches are computationally expensive and unsuitable for rapid design prototyping and real-time control applications. This paper proposes a macro-scale 1-DOF model capable of predicting force and displacement of an MPC diaphragm actuator. Model validation confirmed both blocked force and displacement can be accurately predicted in a variety of working conditions i.e. different magnetic field strengths, static/dynamic fields, and gap distances. The contribution of this work includes a comprehensive experimental investigation of a macro-scale diaphragm actuator; the derivation and validation of a new phenomenological model to describe MPC actuation; and insights into the proposed model’s design-based functionality i.e. scalability and generalizability in terms of magnetic filler concentration and diaphragm diameter. Due to the lumped element modeling approach, the proposed model can also be adapted to alternative actuator configurations, and thus presents a useful tool for design, control and simulation of novel MPC applications.

Steel fiber reinforced concrete behavior, modelling and design

CERN Document Server

Singh, Harvinder

2017-01-01

This book discusses design aspects of steel fiber-reinforced concrete (SFRC) members, including the behavior of the SFRC and its modeling. It also examines the effect of various parameters governing the response of SFRC members in detail. Unlike other publications available in the form of guidelines, which mainly describe design methods based on experimental results, it describes the basic concepts and principles of designing structural members using SFRC as a structural material, predominantly subjected to flexure and shear. Although applications to special structures, such as bridges, retaining walls, tanks and silos are not specifically covered, the fundamental design concepts remain the same and can easily be extended to these elements. It introduces the principles and related theories for predicting the role of steel fibers in reinforcing concrete members concisely and logically, and presents various material models to predict the response of SFRC members in detail. These are then gradually extended to d...

Is Wine a Financial Parachute?

OpenAIRE

Baldi, Lucia; Vandone, Daniela; Peri, Massimo

2010-01-01

This paper analyzes the relationship between Global Wine Industry Share Price Indexes and composite stock market indexes using a Threshold Vector Error Correction Model (TVECM), aiming to investigate if investments in the wine sector play a role in determining financial risk and return to investors who include it in their portfolio. Whilst in most of the literature analyses the return of investments of fine wine, this paper places the focus to “normal” (i.e. non‐fine) wine, using data from th...

Integrated design approach of the pebble BeD modular reactor using models

International Nuclear Information System (INIS)

Venter, Pieter J.; Mitchell, Mark N.

2007-01-01

The pebble bed modular reactor (PBMR) is the first pebble bed reactor that will be utilised in a high temperature direct Brayton cycle configuration. This implies that there are a number of unique features in the PBMR that extend from the German experience base. One of the challenges in the design of the PBMR is developing an understanding of the expected behaviour of the reactor through analyses and simulations and managing the integrated design process between the designers, the physicists and the analysts. This integrated design process is managed through model-based development work. Three-dimensional CAD models are constructed of the components and parts in the reactor. From the CAD models, CFD models, neutronic models, shielding models, FEM models and other thermodynamic models are derived. These models range from very simple models to extremely detailed and complex models. The models are used in legacy software as well as commercial off-the-shelf software. The different models are also used in code-to-code comparisons to verify the results. This paper will briefly discuss the different models and the interaction between the models, and how the models are used in the iterative design process that is used in the development of the reactor at PBMR

Designing tools for oil exploration using nuclear modeling

Science.gov (United States)

Mauborgne, Marie-Laure; Allioli, Françoise; Manclossi, Mauro; Nicoletti, Luisa; Stoller, Chris; Evans, Mike

2017-09-01

When designing nuclear tools for oil exploration, one of the first steps is typically nuclear modeling for concept evaluation and initial characterization. Having an accurate model, including the availability of accurate cross sections, is essential to reduce or avoid time consuming and costly design iterations. During tool response characterization, modeling is benchmarked with experimental data and then used to complement and to expand the database to make it more detailed and inclusive of more measurement environments which are difficult or impossible to reproduce in the laboratory. We present comparisons of our modeling results obtained using the ENDF/B-VI and ENDF/B-VII cross section data bases, focusing on the response to a few elements found in the tool, borehole and subsurface formation. For neutron-induced inelastic and capture gamma ray spectroscopy, major obstacles may be caused by missing or inaccurate cross sections for essential materials. We show examples of the benchmarking of modeling results against experimental data obtained during tool characterization and discuss observed discrepancies.

The impact of design-based modeling instruction on seventh graders' spatial abilities and model-based argumentation

Science.gov (United States)

McConnell, William J.

Due to the call of current science education reform for the integration of engineering practices within science classrooms, design-based instruction is receiving much attention in science education literature. Although some aspect of modeling is often included in well-known design-based instructional methods, it is not always a primary focus. The purpose of this study was to better understand how design-based instruction with an emphasis on scientific modeling might impact students' spatial abilities and their model-based argumentation abilities. In the following mixed-method multiple case study, seven seventh grade students attending a secular private school in the Mid-Atlantic region of the United States underwent an instructional intervention involving design-based instruction, modeling and argumentation. Through the course of a lesson involving students in exploring the interrelatedness of the environment and an animal's form and function, students created and used multiple forms of expressed models to assist them in model-based scientific argument. Pre/post data were collected through the use of The Purdue Spatial Visualization Test: Rotation, the Mental Rotation Test and interviews. Other data included a spatial activities survey, student artifacts in the form of models, notes, exit tickets, and video recordings of students throughout the intervention. Spatial abilities tests were analyzed using descriptive statistics while students' arguments were analyzed using the Instrument for the Analysis of Scientific Curricular Arguments and a behavior protocol. Models were analyzed using content analysis and interviews and all other data were coded and analyzed for emergent themes. Findings in the area of spatial abilities included increases in spatial reasoning for six out of seven participants, and an immense difference in the spatial challenges encountered by students when using CAD software instead of paper drawings to create models. Students perceived 3D printed

Application of Absorption Modeling in Rational Design of Drug Product Under Quality-by-Design Paradigm.

Science.gov (United States)

Kesisoglou, Filippos; Mitra, Amitava

2015-09-01

Physiologically based absorption models can be an important tool in understanding product performance and hence implementation of Quality by Design (QbD) in drug product development. In this report, we show several case studies to demonstrate the potential application of absorption modeling in rational design of drug product under the QbD paradigm. The examples include application of absorption modeling—(1) prior to first-in-human studies to guide development of a formulation with minimal sensitivity to higher gastric pH and hence reduced interaction when co-administered with PPIs and/or H2RAs, (2) design of a controlled release formulation with optimal release rate to meet trough plasma concentrations and enable QD dosing, (3) understanding the impact of API particle size distribution on tablet bioavailability and guide formulation design in late-stage development, (4) assess impact of API phase change on product performance to guide specification setting, and (5) investigate the effect of dissolution rate changes on formulation bioperformance and enable appropriate specification setting. These case studies are meant to highlight the utility of physiologically based absorption modeling in gaining a thorough understanding of the product performance and the critical factors impacting performance to drive design of a robust drug product that would deliver the optimal benefit to the patients.

Modelling conflict management in design: an explicit approach

NARCIS (Netherlands)

Brazier, F.M.; van Langen, P.H.G.; Treur, J.

1995-01-01

This paper focusses on how conflicts that arise during a design process and the management of conflicts can be modelled. A number of possible conflict types are distinguished and it is described how each of them can be detected during the design process, using an explicit meta-representation.

Designing the Distributed Model Integration Framework – DMIF

NARCIS (Netherlands)

Belete, Getachew F.; Voinov, Alexey; Morales, Javier

2017-01-01

We describe and discuss the design and prototype of the Distributed Model Integration Framework (DMIF) that links models deployed on different hardware and software platforms. We used distributed computing and service-oriented development approaches to address the different aspects of

Model-based design of supervisory controllers for baggage handling systems

NARCIS (Netherlands)

Swartjes, L.; van Beek, D.A.; Fokkink, W.J.; van Eekelen, J.A.W.M.

2017-01-01

The complexity of airport baggage handling systems in combination with the required high level of robustness makes designing supervisory controllers for these systems a challenging task. We show how a state of the art, formal, model-based design framework has been successfully used for model-based

Cryogenic Wind Tunnel Models. Design and Fabrication

Science.gov (United States)

Young, C. P., Jr. (Compiler); Gloss, B. B. (Compiler)

1983-01-01

The principal motivating factor was the National Transonic Facility (NTF). Since the NTF can achieve significantly higher Reynolds numbers at transonic speeds than other wind tunnels in the world, and will therefore occupy a unique position among ground test facilities, every effort is being made to ensure that model design and fabrication technology exists to allow researchers to take advantage of this high Reynolds number capability. Since a great deal of experience in designing and fabricating cryogenic wind tunnel models does not exist, and since the experience that does exist is scattered over a number of organizations, there is a need to bring existing experience in these areas together and share it among all interested parties. Representatives from government, the airframe industry, and universities are included.

Implications of Building Information Modeling on Interior Design Education: The Impact on Teaching Design Processes

Directory of Open Access Journals (Sweden)

Amy Roehl, MFA

2013-06-01

Full Text Available Currently, major shifts occur in design processes effecting business practices for industries involved with designing and delivering the built environment. These changing conditions are a direct result of industry adoption of relatively new technologies called BIM or Building Information Modeling. This review of literature examines implications of these changing processes on interior design education.

Design and implementation of new design of numerical experiments for non linear models

International Nuclear Information System (INIS)

Gazut, St.

2007-03-01

This thesis addresses the problem of the construction of surrogate models in numerical simulation. Whenever numerical experiments are costly, the simulation model is complex and difficult to use. It is important then to select the numerical experiments as efficiently as possible in order to minimize their number. In statistics, the selection of experiments is known as optimal experimental design. In the context of numerical simulation where no measurement uncertainty is present, we describe an alternative approach based on statistical learning theory and re-sampling techniques. The surrogate models are constructed using neural networks and the generalization error is estimated by leave-one-out, cross-validation and bootstrap. It is shown that the bootstrap can control the over-fitting and extend the concept of leverage for non linear in their parameters surrogate models. The thesis describes an iterative method called LDR for Learner Disagreement from experiment Re-sampling, based on active learning using several surrogate models constructed on bootstrap samples. The method consists in adding new experiments where the predictors constructed from bootstrap samples disagree most. We compare the LDR method with other methods of experimental design such as D-optimal selection. (author)

Numerical Coupling and Simulation of Point-Mass System with the Turbulent Fluid Flow

Science.gov (United States)

Gao, Zheng

A computational framework that combines the Eulerian description of the turbulence field with a Lagrangian point-mass ensemble is proposed in this dissertation. Depending on the Reynolds number, the turbulence field is simulated using Direct Numerical Simulation (DNS) or eddy viscosity model. In the meanwhile, the particle system, such as spring-mass system and cloud droplets, are modeled using the ordinary differential system, which is stiff and hence poses a challenge to the stability of the entire system. This computational framework is applied to the numerical study of parachute deceleration and cloud microphysics. These two distinct problems can be uniformly modeled with Partial Differential Equations (PDEs) and Ordinary Differential Equations (ODEs), and numerically solved in the same framework. For the parachute simulation, a novel porosity model is proposed to simulate the porous effects of the parachute canopy. This model is easy to implement with the projection method and is able to reproduce Darcy's law observed in the experiment. Moreover, the impacts of using different versions of k-epsilon turbulence model in the parachute simulation have been investigated and conclude that the standard and Re-Normalisation Group (RNG) model may overestimate the turbulence effects when Reynolds number is small while the Realizable model has a consistent performance with both large and small Reynolds number. For another application, cloud microphysics, the cloud entrainment-mixing problem is studied in the same numerical framework. Three sets of DNS are carried out with both decaying and forced turbulence. The numerical result suggests a new way parameterize the cloud mixing degree using the dynamical measures. The numerical experiments also verify the negative relationship between the droplets number concentration and the vorticity field. The results imply that the gravity has fewer impacts on the forced turbulence than the decaying turbulence. In summary, the

A Common Probe Design for Multiple Planetary Destinations

Science.gov (United States)

Hwang, H. H.; Allen, G. A., Jr.; Alunni, A. I.; Amato, M. J.; Atkinson, D. H.; Bienstock, B. J.; Cruz, J. R.; Dillman, R. A.; Cianciolo, A. D.; Elliott, J. O.;

Models and Methods for Structural Topology Optimization with Discrete Design Variables

DEFF Research Database (Denmark)

Stolpe, Mathias

in the conceptual design phase to find innovative designs. The strength of topology optimization is the capability of determining both the optimal shape and the topology of the structure. In some cases also the optimal material properties can be determined. Optimal structural design problems are modeled...... such as bridges, airplanes, wind turbines, cars, etc. Topology optimization is a collection of theory, mathematical models, and numerical methods and is often used in the conceptual design phase to find innovative designs. The strength of topology optimization is the capability of determining both the optimal......Structural topology optimization is a multi-disciplinary research field covering optimal design of load carrying mechanical structures such as bridges, airplanes, wind turbines, cars, etc. Topology optimization is a collection of theory, mathematical models, and numerical methods and is often used...

Designing healthy communities: Testing the walkability model

OpenAIRE

Zuniga-Teran, Adriana; Orr, Barron; Gimblett, Randy; Chalfoun, Nader; Marsh, Stuart; Guertin, David; Going, Scott

2017-01-01

Research from multiple domains has provided insights into how neighborhood design can be improved to have a more favorable effect on physical activity, a concept known as walkability. The relevant research findings/hypotheses have been integrated into a Walkability Framework, which organizes the design elements into nine walkability categories. The purpose of this study was to test whether this conceptual framework can be used as a model to measure the interactions between the built environme...

Reduced cost mission design using surrogate models

Science.gov (United States)

Feldhacker, Juliana D.; Jones, Brandon A.; Doostan, Alireza; Hampton, Jerrad

2016-01-01

This paper uses surrogate models to reduce the computational cost associated with spacecraft mission design in three-body dynamical systems. Sampling-based least squares regression is used to project the system response onto a set of orthogonal bases, providing a representation of the ΔV required for rendezvous as a reduced-order surrogate model. Models are presented for mid-field rendezvous of spacecraft in orbits in the Earth-Moon circular restricted three-body problem, including a halo orbit about the Earth-Moon L2 libration point (EML-2) and a distant retrograde orbit (DRO) about the Moon. In each case, the initial position of the spacecraft, the time of flight, and the separation between the chaser and the target vehicles are all considered as design inputs. The results show that sample sizes on the order of 102 are sufficient to produce accurate surrogates, with RMS errors reaching 0.2 m/s for the halo orbit and falling below 0.01 m/s for the DRO. A single function call to the resulting surrogate is up to two orders of magnitude faster than computing the same solution using full fidelity propagators. The expansion coefficients solved for in the surrogates are then used to conduct a global sensitivity analysis of the ΔV on each of the input parameters, which identifies the separation between the spacecraft as the primary contributor to the ΔV cost. Finally, the models are demonstrated to be useful for cheap evaluation of the cost function in constrained optimization problems seeking to minimize the ΔV required for rendezvous. These surrogate models show significant advantages for mission design in three-body systems, in terms of both computational cost and capabilities, over traditional Monte Carlo methods.

Inverse problems in the design, modeling and testing of engineering systems

Science.gov (United States)

Alifanov, Oleg M.

1991-01-01

Formulations, classification, areas of application, and approaches to solving different inverse problems are considered for the design of structures, modeling, and experimental data processing. Problems in the practical implementation of theoretical-experimental methods based on solving inverse problems are analyzed in order to identify mathematical models of physical processes, aid in input data preparation for design parameter optimization, help in design parameter optimization itself, and to model experiments, large-scale tests, and real tests of engineering systems.

Optimal Experimental Design for Model Discrimination

Science.gov (United States)

Myung, Jay I.; Pitt, Mark A.

2009-01-01

Models of a psychological process can be difficult to discriminate experimentally because it is not easy to determine the values of the critical design variables (e.g., presentation schedule, stimulus structure) that will be most informative in differentiating them. Recent developments in sampling-based search methods in statistics make it…

A Review of Research on Universal Design Educational Models

Science.gov (United States)

Rao, Kavita; Ok, Min Wook; Bryant, Brian R.

2014-01-01

Universal design for learning (UDL) has gained considerable attention in the field of special education, acclaimed for its promise to promote inclusion by supporting access to the general curriculum. In addition to UDL, there are two other universal design (UD) educational models referenced in the literature, universal design of instruction (UDI)…

An anthology of theories and models of design philosophy, approaches and empirical explorations

CERN Document Server

Blessing, Lucienne

2014-01-01

While investigations into both theories and models has remained a major strand of engineering design research, current literature sorely lacks a reference book that provides a comprehensive and up-to-date anthology of theories and models, and their philosophical and empirical underpinnings; An Anthology of Theories and Models of Design fills this gap. The text collects the expert views of an international authorship, covering: ·         significant theories in engineering design, including CK theory, domain theory, and the theory of technical systems; ·         current models of design, from a function behavior structure model to an integrated model; ·         important empirical research findings from studies into design; and ·         philosophical underpinnings of design itself. For educators and researchers in engineering design, An Anthology of Theories and Models of Design gives access to in-depth coverage of theoretical and empirical developments in this area; for pr...

Design Systems Group: knowledge models for design and engineering (2005-2010)

NARCIS (Netherlands)

Vries, de B.; Beetz, J.; Achten, H.H.; Dijkstra, J.; Jessurun, A.J.; Achten, H.H.; Vries, de B.; Stappers, P.J.

2010-01-01

The Design Systems chair of the Eindhoven University of Technology has two main lines of research, namely: (1) Product and Process modeling and (2) Simulation of Human Behavior in the Built Environment. In the period 2005 – 2010 three PhD’s defended their thesis and 11 students received their

Distance Education for the Gifted and Talented: An Interactive Design Model.

Science.gov (United States)

McKinnon, David H.; Nolan, C. J. Patrick

1999-01-01

Discusses development of an Australian distance-education cosmology course that employs an interactive design model and an extensive communication system. The way the model is used to organized, sequence, and deliver the course is explained. Discussion addresses how the model might be used to design other courses. (Author/CR)

Model-Based approaches to Human-Automation Systems Design

DEFF Research Database (Denmark)

Jamieson, Greg A.; Andersson, Jonas; Bisantz, Ann

2012-01-01

Human-automation interaction in complex systems is common, yet design for this interaction is often conducted without explicit consideration of the role of the human operator. Fortunately, there are a number of modeling frameworks proposed for supporting this design activity. However...... (and reportedly one or two critics) can engage one another on several agreed questions about such frameworks. The goal is to aid non-aligned practitioners in choosing between alternative frameworks for their human-automation interaction design challenges....

Integrated predictive modelling simulations of burning plasma experiment designs

International Nuclear Information System (INIS)

Bateman, Glenn; Onjun, Thawatchai; Kritz, Arnold H

2003-01-01

Models for the height of the pedestal at the edge of H-mode plasmas (Onjun T et al 2002 Phys. Plasmas 9 5018) are used together with the Multi-Mode core transport model (Bateman G et al 1998 Phys. Plasmas 5 1793) in the BALDUR integrated predictive modelling code to predict the performance of the ITER (Aymar A et al 2002 Plasma Phys. Control. Fusion 44 519), FIRE (Meade D M et al 2001 Fusion Technol. 39 336), and IGNITOR (Coppi B et al 2001 Nucl. Fusion 41 1253) fusion reactor designs. The simulation protocol used in this paper is tested by comparing predicted temperature and density profiles against experimental data from 33 H-mode discharges in the JET (Rebut P H et al 1985 Nucl. Fusion 25 1011) and DIII-D (Luxon J L et al 1985 Fusion Technol. 8 441) tokamaks. The sensitivities of the predictions are evaluated for the burning plasma experimental designs by using variations of the pedestal temperature model that are one standard deviation above and below the standard model. Simulations of the fusion reactor designs are carried out for scans in which the plasma density and auxiliary heating power are varied

A systems modelling framework for the design of integrated process control systems

International Nuclear Information System (INIS)

Lind, M.

1983-12-01

The paper describes a systems modelling methodology, called multilevel flow modelling, or MFM, which aims at describing complex production plants as designs, i.e. as systems having goals, functions and equipment realizing these functions. The modelling concepts are based on thermodynamics and lead to a system description in terms of multiple levels of interrelated mass or energy flow structures. The paper discusses as a basis for the modelling framework the general properties of artifacts or designs, characterizes the complexity of production systems and defines the MFM concepts which allow a consistent specification of goals and functions of these systems as generated in the process design. A modelling example is given and the application of the models for the design of plant control strategies is outlined. (author)

Evaluation of End-Products in Architecture Design Process: A Fuzzy Decision-Making Model

Directory of Open Access Journals (Sweden)

Serkan PALABIYIK

2012-06-01

Full Text Available This paper presents a study on the development of a fuzzy multi-criteria decision-making model for the evaluation of end products of the architectural design process. Potentials of the developed model were investigated within the scope of architectural design education, specifically an international design studio titled “Design for Disassembly and Reuse: Design & Building Multipurpose Transformable Pavilions.” The studio work followed a design process that integrated systematic and heuristic thinking. The design objectives and assessment criteria were clearly set out at the beginning of the process by the studio coordinator with the aim of narrowing the design space and increasing awareness of the consequences of design decisions. At the end of the design process, designs produced in the studio were evaluated using the developed model to support decision making. The model facilitated the identification of positive and negative aspects of the designs and selection of the design alternative that best met the studio objectives set at the beginning.

SOFTWARE DESIGN MODELLING WITH FUNCTIONAL PETRI NETS

African Journals Online (AJOL)

Dr Obe

the system, which can be described as a set of conditions. ... FPN Software prototype proposed for the conventional programming construct: if-then-else ... mathematical modeling tool allowing for ... methods and techniques of software design.

An integrated management tool for rockfall evaluation along transportation corridors: the ParaChute research project

Science.gov (United States)

Cloutier, Catherine; Locat, Jacques; Mayers, Mélanie; Noël, François; Turmel, Dominique; Jacob, Chantal; Dorval, Pierre; Bossé, François; Gionet, Pierre; Jaboyedoff, Michel

2016-04-01

Rockfall is a significant hazard along linear infrastructures due to the presence of natural and man-made rock slopes. Knowing where the problematic rockfalls source areas are is of primary importance to properly manage and mitigate the risk associated to rockfall along linear infrastructures. The aim of the ParaChute research project is to integrate various technologies into a workflow for rockfall characterization for such infrastructures, using a 220 km-long railroad as the study site which is located on Québec's North Shore, Canada. The objectives of this 3-year project which started in 2014 are: (1) to optimize the use of terrestrial, mobile and airborne laser scanners data into terrain analysis, structural geology analysis and rockfall susceptibility rating, (2) to further develop the use of unmanned aerial vehicles (UAV) for photogrammetry applied to rock cliff characterization, and (3) to integrate rockfall simulation studies into a rock slope classification system similar to the Rockfall Hazard Rating System. Firstly, based on laser scanner data and aerial photographs, the morpho-structural features of the terrain (genetic material, landform, drainage, etc.) are mapped. The result can be used to assess all types of mass movements. Secondly, to guide field work and decrease uncertainty of various parameters, systematic rockfall simulations and a first structural analysis are made from point clouds acquired by mobile and airborne laser scanner. The simulation results are used to recognize the rock slopes that have potentially problematic rockfall paths, meaning they could reach the linear infrastructure. Other rock slopes are not included in the inventory. Field work is carried out to validate and complete the rock slopes characterization previously made from remote sensing technique. Because some or parts of cliffs are not visible or accessible from the railroad, we are currently developing the use of photogrammetry by UAV in order to complete the

Content Analysis of Research Trends in Instructional Design Models: 1999-2014

Science.gov (United States)

Göksu, Idris; Özcan, Kursat Volkan; Çakir, Recep; Göktas, Yuksel

2017-01-01

This study examines studies on instructional design models by applying content analysis. It covers 113 papers published in 44 international Social Science Citation Index (SSCI) and Science Citation Index (SCI) journals. Studies on instructional design models are explored in terms of journal of publication, preferred model, country where the study…

Model-based computer-aided design for controlled release of pesticides

DEFF Research Database (Denmark)

Muro Sunè, Nuria; Gani, Rafiqul; Bell, G.

2005-01-01

In the field of controlled release technology for pesticides or active ingredients (AI), models that can predict its delivery during application are important for purposes of design and marketing of the pesticide product. Appropriate models for the controlled release of pesticides, if available, ...... extended models have been developed and implemented into a computer-aided system. The total model consisting of the property models embedded into the release models are then employed to study the release of different combinations of AIs and polymer-based microcapsules.......In the field of controlled release technology for pesticides or active ingredients (AI), models that can predict its delivery during application are important for purposes of design and marketing of the pesticide product. Appropriate models for the controlled release of pesticides, if available...

Control Relevant Modeling and Design of Scramjet-Powered Hypersonic Vehicles

Science.gov (United States)

Dickeson, Jeffrey James

This report provides an overview of scramjet-powered hypersonic vehicle modeling and control challenges. Such vehicles are characterized by unstable non-minimum phase dynamics with significant coupling and low thrust margins. Recent trends in hypersonic vehicle research are summarized. To illustrate control relevant design issues and tradeoffs, a generic nonlinear 3DOF longitudinal dynamics model capturing aero-elastic-propulsive interactions for wedge-shaped vehicle is used. Limitations of the model are discussed and numerous modifications have been made to address control relevant needs. Two different baseline configurations are examined over a two-stage to orbit ascent trajectory. The report highlights how vehicle level-flight static (trim) and dynamic properties change over the trajectory. Thermal choking constraints are imposed on control system design as a direct consequence of having a finite FER margin. The implication of this state-dependent nonlinear FER margin constraint, the right half plane (RHP) zero, and lightly damped flexible modes, on control system bandwidth (BW) and FPA tracking has been discussed. A control methodology has been proposed that addresses the above dynamics while providing some robustness to modeling uncertainty. Vehicle closure (the ability to fly a trajectory segment subject to constraints) is provided through a proposed vehicle design methodology. The design method attempts to use open loop metrics whenever possible to design the vehicle. The design method is applied to a vehicle/control law closed loop nonlinear simulation for validation. The 3DOF longitudinal modeling results are validated against a newly released NASA 6DOF code.

Is the Linear Modeling Technique Good Enough for Optimal Form Design? A Comparison of Quantitative Analysis Models

Science.gov (United States)

Lin, Yang-Cheng; Yeh, Chung-Hsing; Wang, Chen-Cheng; Wei, Chun-Chun

2012-01-01

How to design highly reputable and hot-selling products is an essential issue in product design. Whether consumers choose a product depends largely on their perception of the product image. A consumer-oriented design approach presented in this paper helps product designers incorporate consumers' perceptions of product forms in the design process. The consumer-oriented design approach uses quantification theory type I, grey prediction (the linear modeling technique), and neural networks (the nonlinear modeling technique) to determine the optimal form combination of product design for matching a given product image. An experimental study based on the concept of Kansei Engineering is conducted to collect numerical data for examining the relationship between consumers' perception of product image and product form elements of personal digital assistants (PDAs). The result of performance comparison shows that the QTTI model is good enough to help product designers determine the optimal form combination of product design. Although the PDA form design is used as a case study, the approach is applicable to other consumer products with various design elements and product images. The approach provides an effective mechanism for facilitating the consumer-oriented product design process. PMID:23258961

Computer-aided polymer design using group contribution plus property models

DEFF Research Database (Denmark)

Satyanarayana, Kavitha Chelakara; Abildskov, Jens; Gani, Rafiqul

2009-01-01

. Polymer repeat unit property prediction models are required to calculate the properties of the generated repeat units. A systematic framework incorporating recently developed group contribution plus (GC(+)) models and an extended CAMD technique to include design of polymer repeat units is highlighted...... in this paper. The advantage of a GC(+) model in CAMD applications is that a very large number of polymer structures can be considered even though some of the group parameters may not be available. A number of case studies involving different polymer design problems have been solved through the developed......The preliminary step for polymer product design is to identify the basic repeat unit structure of the polymer that matches the target properties. Computer-aided molecular design (CAMD) approaches can be applied for generating the polymer repeat unit structures that match the required constraints...

Property Model-based Tailor-made Design of Chemical-based Products

DEFF Research Database (Denmark)

Kalakul, Sawitree

Computer-aided model-based methods and tools are increasingly playing important roles in chemical product design. They have the potential to very quickly search for and identify reliable product candidates that can then be verified through experiments. Inthis way, the time and resources spent...... on experiment are reduced leading to faster and cheaper to market the products. The tools also help to manage the solution of product design problems, which usually require efficient handling of model-data-knowledge from different sources and at different time and size scales. The main contribution...... the needed template for a desired product is not available. VPPD-Lab employs a suite of algorithms(such as database search, molecular and mixture blend design) and toolboxes (such asproperty calculations and property model consistency tests) for specific product property prediction, design, and/or analysis...

Designing tools for oil exploration using nuclear modeling

Directory of Open Access Journals (Sweden)

Mauborgne Marie-Laure

2017-01-01

Full Text Available When designing nuclear tools for oil exploration, one of the first steps is typically nuclear modeling for concept evaluation and initial characterization. Having an accurate model, including the availability of accurate cross sections, is essential to reduce or avoid time consuming and costly design iterations. During tool response characterization, modeling is benchmarked with experimental data and then used to complement and to expand the database to make it more detailed and inclusive of more measurement environments which are difficult or impossible to reproduce in the laboratory. We present comparisons of our modeling results obtained using the ENDF/B-VI and ENDF/B-VII cross section data bases, focusing on the response to a few elements found in the tool, borehole and subsurface formation. For neutron-induced inelastic and capture gamma ray spectroscopy, major obstacles may be caused by missing or inaccurate cross sections for essential materials. We show examples of the benchmarking of modeling results against experimental data obtained during tool characterization and discuss observed discrepancies.

Experimental Design for Sensitivity Analysis of Simulation Models

NARCIS (Netherlands)

Kleijnen, J.P.C.

2001-01-01

This introductory tutorial gives a survey on the use of statistical designs for what if-or sensitivity analysis in simulation.This analysis uses regression analysis to approximate the input/output transformation that is implied by the simulation model; the resulting regression model is also known as

Uncertainty Driven Action (UDA) model: A foundation for unifying perspectives on design activity

DEFF Research Database (Denmark)

Cash, Philip; Kreye, Melanie

2017-01-01

are linked via uncertainty perception. The foundations of the UDA model in the design literature are elaborated in terms of the three core actions and their links to designer cognition and behaviour, utilising definitions and concepts from Activity Theory. The practical relevance and theoretical......This paper proposes the Uncertainty Driven Action (UDA) model, which unifies the fragmented literature on design activity. The UDA model conceptualises design activity as a process consisting of three core actions: information action, knowledge-sharing action, and representation action, which...... contributions of the UDA model are discussed. This paper contributes to the design literature by offering a comprehensive formalisation of design activity of individual designers, which connects cognition and action, to provide a foundation for understanding previously disparate descriptions of design activity....

Designing Public Library Websites for Teens: A Conceptual Model

Science.gov (United States)

Naughton, Robin Amanda

2012-01-01

The main goal of this research study was to develop a conceptual model for the design of public library websites for teens (TLWs) that would enable designers and librarians to create library websites that better suit teens' information needs and practices. It bridges a gap in the research literature between user interface design in human-computer…

A Conceptual Culture Model for Design Science Research

Directory of Open Access Journals (Sweden)

Thomas Richter

2016-03-01

Full Text Available The aim of design science research (DSR in information systems is the user-centred creation of IT-artifacts with regard to specific social environments. For culture research in the field, which is necessary for a proper localization of IT-artifacts, models and research approaches from social sciences usually are adopted. Descriptive dimension-based culture models most commonly are applied for this purpose, which assume culture being a national phenomenon and tend to reduce it to basic values. Such models are useful for investigations in behavioural culture research because it aims to isolate, describe and explain culture-specific attitudes and characteristics within a selected society. In contrast, with the necessity to deduce concrete decisions for artifact-design, research results from DSR need to go beyond this aim. As hypothesis, this contribution generally questions the applicability of such generic culture dimensions’ models for DSR and focuses on their theoretical foundation, which goes back to Hofstede’s conceptual Onion Model of Culture. The herein applied literature-based analysis confirms the hypothesis. Consequently, an alternative conceptual culture model is being introduced and discussed as theoretical foundation for culture research in DSR.

Models and Tabu Search Metaheuristics for Service Network Design with Asset-Balance Requirements

DEFF Research Database (Denmark)

Pedersen, Michael Berliner; Crainic, T.G.; Madsen, Oli B.G.

2009-01-01

This paper focuses on a generic model for service network design, which includes asset positioning and utilization through constraints on asset availability at terminals. We denote these relations as "design-balance constraints" and focus on the design-balanced capacitated multicommodity network...... design model, a generalization of the capacitated multicommodity network design model generally used in service network design applications. Both arc-and cycle-based formulations for the new model are presented. The paper also proposes a tabu search metaheuristic framework for the arc-based formulation....... Results on a wide range of network design problem instances from the literature indicate the proposed method behaves very well in terms of computational efficiency and solution quality....

Parametric design and analysis framework with integrated dynamic models

DEFF Research Database (Denmark)

Negendahl, Kristoffer

2014-01-01

of building energy and indoor environment, are generally confined to late in the design process. Consequence based design is a framework intended for the early design stage. It involves interdisciplinary expertise that secures validity and quality assurance with a simulationist while sustaining autonomous...... control with the building designer. Consequence based design is defined by the specific use of integrated dynamic modeling, which includes the parametric capabilities of a scripting tool and building simulation features of a building performance simulation tool. The framework can lead to enhanced...

A Concept Transformation Learning Model for Architectural Design Learning Process

Science.gov (United States)

Wu, Yun-Wu; Weng, Kuo-Hua; Young, Li-Ming

2016-01-01

Generally, in the foundation course of architectural design, much emphasis is placed on teaching of the basic design skills without focusing on teaching students to apply the basic design concepts in their architectural designs or promoting students' own creativity. Therefore, this study aims to propose a concept transformation learning model to…

Microstructure Characterization and Modeling for Improved Electrode Design

Energy Technology Data Exchange (ETDEWEB)

Smith, Kandler A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Usseglio Viretta, Francois L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Graf, Peter A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Santhanagopalan, Shriram [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Pesaran, Ahmad A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Yao, Koffi (Pierre) [Argonne National Laboratory; ; Dees, Dennis [Argonne National Laboratory; Jansen, Andy [Argonne National Laboratory; Mukherjee, Partha [Texas A& M University; Mistry, Aashutosh [Texas A& M University; Verma, Ankit [Texas A& M University

2017-08-03

This presentation describes research work led by NREL with team members from Argonne National Laboratory and Texas A&M University in microstructure analysis, modeling and validation under DOE's Computer-Aided Engineering of Batteries (CAEBAT) program. The goal of the project is to close the gaps between CAEBAT models and materials research by creating predictive models that can be used for electrode design.

Modelling and controller design for a UV disinfection plant

NARCIS (Netherlands)

van Mourik, S.; Geurts, Bernardus J.; Zwart, Heiko J.

2007-01-01

A mathematical model describing fluid flow and concentration dynamics of microorganisms inside a UV photoreactor is developed. Using physical arguments and techniques from system theory, we approximate this model by a first order linear one. For this reduced model, we design a controller. The

Building Information Modeling for Managing Design and Construction

DEFF Research Database (Denmark)

Berard, Ole Bengt

outcome of construction work. Even though contractors regularly encounter design information problems, these issues are accepted as a condition of doing business and better design information has yet to be defined. Building information modeling has the inherent promise of improving the quality of design...... information for work tasks. * Amount of Information – the number of documents and files, and other media, should be appropriate for the scope. The criteria were identified by empirical studies and theory on information quality in the architectural, engineering and construction (AEC) industry and other fields......Contractors planning and executing construction work encounter many kinds of problems with design information, such as uncoordinated drawings and specification, missing relevant information, and late delivery of design information. Research has shown that missing design information and unintended...

The Impact of Statistical Leakage Models on Design Yield Estimation

Directory of Open Access Journals (Sweden)

Rouwaida Kanj

2011-01-01

Full Text Available Device mismatch and process variation models play a key role in determining the functionality and yield of sub-100 nm design. Average characteristics are often of interest, such as the average leakage current or the average read delay. However, detecting rare functional fails is critical for memory design and designers often seek techniques that enable accurately modeling such events. Extremely leaky devices can inflict functionality fails. The plurality of leaky devices on a bitline increase the dimensionality of the yield estimation problem. Simplified models are possible by adopting approximations to the underlying sum of lognormals. The implications of such approximations on tail probabilities may in turn bias the yield estimate. We review different closed form approximations and compare against the CDF matching method, which is shown to be most effective method for accurate statistical leakage modeling.

Ontology-Based Big Dimension Modeling in Data Warehouse Schema Design

DEFF Research Database (Denmark)

Iftikhar, Nadeem

2013-01-01

During data warehouse schema design, designers often encounter how to model big dimensions that typically contain a large number of attributes and records. To investigate effective approaches for modeling big dimensions is necessary in order to achieve better query performance, with respect...... partitioning, vertical partitioning and their hybrid. We formalize the design methods and propose an algorithm that describes the modeling process from an OWL ontology to a data warehouse schema. In addition, this paper also presents an effective ontology-based tool to automate the modeling process. The tool...... can automatically generate the data warehouse schema from the ontology of describing the terms and business semantics for the big dimension. In case of any change in the requirements, we only need to modify the ontology, and re-generate the schema using the tool. This paper also evaluates the proposed...

Building information modeling in the architectural design phases

DEFF Research Database (Denmark)

Hermund, Anders

2009-01-01

The overall economical benefits of Building Information Modeling are generally comprehensible, but are there other problems with the implementation of BIM as a formulized system in a field that ultimately is dependant on a creative input? Is optimization and economic benefit really contributing...... with an architectural quality? In Denmark the implementation of the digital working methods related to BIM has been introduced by government law in 2007. Will the important role of the architect as designer change in accordance with these new methods, and does the idea of one big integrated model represent a paradox...... in relation to designing? The BIM mindset requires changes on many levels....

Latent spatial models and sampling design for landscape genetics

Science.gov (United States)

Hanks, Ephraim M.; Hooten, Mevin B.; Knick, Steven T.; Oyler-McCance, Sara J.; Fike, Jennifer A.; Cross, Todd B.; Schwartz, Michael K.

2016-01-01

We propose a spatially-explicit approach for modeling genetic variation across space and illustrate how this approach can be used to optimize spatial prediction and sampling design for landscape genetic data. We propose a multinomial data model for categorical microsatellite allele data commonly used in landscape genetic studies, and introduce a latent spatial random effect to allow for spatial correlation between genetic observations. We illustrate how modern dimension reduction approaches to spatial statistics can allow for efficient computation in landscape genetic statistical models covering large spatial domains. We apply our approach to propose a retrospective spatial sampling design for greater sage-grouse (Centrocercus urophasianus) population genetics in the western United States.

An information model to support user-centered design of medical devices.

Science.gov (United States)

Hagedorn, Thomas J; Krishnamurty, Sundar; Grosse, Ian R

2016-08-01

The process of engineering design requires the product development team to balance the needs and limitations of many stakeholders, including those of the user, regulatory organizations, and the designing institution. This is particularly true in medical device design, where additional consideration must be given for a much more complex user-base that can only be accessed on a limited basis. Given this inherent challenge, few projects exist that consider design domain concepts, such as aspects of a detailed design, a detailed view of various stakeholders and their capabilities, along with the user-needs simultaneously. In this paper, we present a novel information model approach that combines a detailed model of design elements with a model of the design itself, customer requirements, and of the capabilities of the customer themselves. The information model is used to facilitate knowledge capture and automated reasoning across domains with a minimal set of rules by adopting a terminology that treats customer and design specific factors identically, thus enabling straightforward assessments. A uniqueness of this approach is that it systematically provides an integrated perspective on the key usability information that drive design decisions towards more universal or effective outcomes with the very design information impacted by the usability information. This can lead to cost-efficient optimal designs based on a direct inclusion of the needs of customers alongside those of business, marketing, and engineering requirements. Two case studies are presented to show the method's potential as a more effective knowledge management tool with built-in automated inferences that provide design insight, as well as its overall effectiveness as a platform to develop and execute medical device design from a holistic perspective. Copyright © 2016 Elsevier Inc. All rights reserved.

Property Modelling for Applications in Chemical Product and Process Design

DEFF Research Database (Denmark)

Gani, Rafiqul

such as database, property model library, model parameter regression, and, property-model based product-process design will be presented. The database contains pure component and mixture data for a wide range of organic chemicals. The property models are based on the combined group contribution and atom...... is missing, the atom connectivity based model is employed to predict the missing group interaction. In this way, a wide application range of the property modeling tool is ensured. Based on the property models, targeted computer-aided techniques have been developed for design and analysis of organic chemicals......, polymers, mixtures as well as separation processes. The presentation will highlight the framework (ICAS software) for property modeling, the property models and issues such as prediction accuracy, flexibility, maintenance and updating of the database. Also, application issues related to the use of property...

Hospital information system: reusability, designing, modelling, recommendations for implementing.

Science.gov (United States)

Huet, B

1998-01-01

The aims of this paper are to precise some essential conditions for building reuse models for hospital information systems (HIS) and to present an application for hospital clinical laboratories. Reusability is a general trend in software, however reuse can involve a more or less part of design, classes, programs; consequently, a project involving reusability must be precisely defined. In the introduction it is seen trends in software, the stakes of reuse models for HIS and the special use case constituted with a HIS. The main three parts of this paper are: 1) Designing a reuse model (which objects are common to several information systems?) 2) A reuse model for hospital clinical laboratories (a genspec object model is presented for all laboratories: biochemistry, bacteriology, parasitology, pharmacology, ...) 3) Recommendations for generating plug-compatible software components (a reuse model can be implemented as a framework, concrete factors that increase reusability are presented). In conclusion reusability is a subtle exercise of which project must be previously and carefully defined.

Embedded Control System Design A Model Based Approach

CERN Document Server

Forrai, Alexandru

2013-01-01

Control system design is a challenging task for practicing engineers. It requires knowledge of different engineering fields, a good understanding of technical specifications and good communication skills. The current book introduces the reader into practical control system design, bridging  the gap between theory and practice.  The control design techniques presented in the book are all model based., considering the needs and possibilities of practicing engineers. Classical control design techniques are reviewed and methods are presented how to verify the robustness of the design. It is how the designed control algorithm can be implemented in real-time and tested, fulfilling different safety requirements. Good design practices and the systematic software development process are emphasized in the book according to the generic standard IEC61508. The book is mainly addressed to practicing control and embedded software engineers - working in research and development – as well as graduate students who are face...

Rational Design of Glucose-Responsive Insulin Using Pharmacokinetic Modeling.

Science.gov (United States)

Bakh, Naveed A; Bisker, Gili; Lee, Michael A; Gong, Xun; Strano, Michael S

2017-11-01

A glucose responsive insulin (GRI) is a therapeutic that modulates its potency, concentration, or dosing of insulin in relation to a patient's dynamic glucose concentration, thereby approximating aspects of a normally functioning pancreas. Current GRI design lacks a theoretical basis on which to base fundamental design parameters such as glucose reactivity, dissociation constant or potency, and in vivo efficacy. In this work, an approach to mathematically model the relevant parameter space for effective GRIs is induced, and design rules for linking GRI performance to therapeutic benefit are developed. Well-developed pharmacokinetic models of human glucose and insulin metabolism coupled to a kinetic model representation of a freely circulating GRI are used to determine the desired kinetic parameters and dosing for optimal glycemic control. The model examines a subcutaneous dose of GRI with kinetic parameters in an optimal range that results in successful glycemic control within prescribed constraints over a 24 h period. Additionally, it is demonstrated that the modeling approach can find GRI parameters that enable stable glucose levels that persist through a skipped meal. The results provide a framework for exploring the parameter space of GRIs, potentially without extensive, iterative in vivo animal testing. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ares Upper Stage Processes to Implement Model Based Design - Going Paperless

Science.gov (United States)

Gregory, Melanie

2012-01-01

Computer-Aided Design (CAD) has all but replaced the drafting board for design work. Increased productivity and accuracy should be natural outcomes of using CAD. Going from paper drawings only to paper drawings based on CAD models to CAD models and no drawings, or Model Based Design (MBD), is a natural progression in today?s world. There are many advantages to MBD over traditional design methods. To make the most of those advantages, standards should be in place and the proper foundation should be laid prior to transitioning to MBD. However, without a full understanding of the implications of MBD and the proper control of the data, the advantages are greatly diminished. Transitioning from a paper design world to an electronic design world means re-thinking how information gets controlled at its origin and distributed from one point to another. It means design methodology is critical, especially for large projects. It means preparation of standardized parts and processes as well as strong communication between all parties in order to maximize the benefits of MBD.

Performance modeling & simulation of complex systems (A systems engineering design & analysis approach)

Science.gov (United States)

Hall, Laverne

1995-01-01

Modeling of the Multi-mission Image Processing System (MIPS) will be described as an example of the use of a modeling tool to design a distributed system that supports multiple application scenarios. This paper examines: (a) modeling tool selection, capabilities, and operation (namely NETWORK 2.5 by CACl), (b) pointers for building or constructing a model and how the MIPS model was developed, (c) the importance of benchmarking or testing the performance of equipment/subsystems being considered for incorporation the design/architecture, (d) the essential step of model validation and/or calibration using the benchmark results, (e) sample simulation results from the MIPS model, and (f) how modeling and simulation analysis affected the MIPS design process by having a supportive and informative impact.

Constitutive Models for Design of Sustainable Concrete Structures

Science.gov (United States)

Brozovsky, J.; Cajka, R.; Koktan, J.

2018-04-01

The paper deals with numerical models of reinforced concrete which are expected to be useful to enhance design of sustainable reinforced concrete structures. That is, the models which can deliver higher precision of results than the linear elastic models but which are still feasible for engineering practice. Such models can be based on an elastic-plastic material. The paper discusses properties of such models. A material model based of the Chen criteria and the Ohtani hardening model for concrete was selected for further development. There is also given a comparison of behaviour of such model with behaviour of a more complex smeared crack model which is based on principles of fracture mechanics.

WDM Systems and Networks Modeling, Simulation, Design and Engineering

CERN Document Server

Ellinas, Georgios; Roudas, Ioannis

2012-01-01

WDM Systems and Networks: Modeling, Simulation, Design and Engineering provides readers with the basic skills, concepts, and design techniques used to begin design and engineering of optical communication systems and networks at various layers. The latest semi-analytical system simulation techniques are applied to optical WDM systems and networks, and a review of the various current areas of optical communications is presented. Simulation is mixed with experimental verification and engineering to present the industry as well as state-of-the-art research. This contributed volume is divided into three parts, accommodating different readers interested in various types of networks and applications. The first part of the book presents modeling approaches and simulation tools mainly for the physical layer including transmission effects, devices, subsystems, and systems), whereas the second part features more engineering/design issues for various types of optical systems including ULH, access, and in-building system...

Developing and Testing Rational Models of Message Design.

Science.gov (United States)

O'Keefe, Barbara J.

1992-01-01

Responds to an article in the same issue regarding research methods for conversational cognition. Argues for a noncognitive view of rational models in communication research. Sets out an analysis of the kinds of claims made by rational models of message design. Discusses the implications of this analysis for studies of the cognitive processes…

Force 2025 and Beyond Strategic Force Design Analytic Model

Science.gov (United States)

2017-01-12

focused thinking , functional hierarchy, task capability matching 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT U 18. NUMBER OF...describe and evaluate current organizational designs in terms of Force Employment and Force Design using the model to offer recommendations and analysis...developed to illuminate the current organizational design structure to better understand how the network of BCTs and enablers function in today’s steady

Overview of SDCM - The Spacecraft Design and Cost Model

Science.gov (United States)

Ferebee, Melvin J.; Farmer, Jeffery T.; Andersen, Gregory C.; Flamm, Jeffery D.; Badi, Deborah M.

1988-01-01

The Spacecraft Design and Cost Model (SDCM) is a computer-aided design and analysis tool for synthesizing spacecraft configurations, integrating their subsystems, and generating information concerning on-orbit servicing and costs. SDCM uses a bottom-up method in which the cost and performance parameters for subsystem components are first calculated; the model then sums the contributions from individual components in order to obtain an estimate of sizes and costs for each candidate configuration within a selected spacecraft system. An optimum spacraft configuration can then be selected.

Computational Methods for Modeling Aptamers and Designing Riboswitches

Directory of Open Access Journals (Sweden)

Sha Gong

2017-11-01

Full Text Available Riboswitches, which are located within certain noncoding RNA region perform functions as genetic “switches”, regulating when and where genes are expressed in response to certain ligands. Understanding the numerous functions of riboswitches requires computation models to predict structures and structural changes of the aptamer domains. Although aptamers often form a complex structure, computational approaches, such as RNAComposer and Rosetta, have already been applied to model the tertiary (three-dimensional (3D structure for several aptamers. As structural changes in aptamers must be achieved within the certain time window for effective regulation, kinetics is another key point for understanding aptamer function in riboswitch-mediated gene regulation. The coarse-grained self-organized polymer (SOP model using Langevin dynamics simulation has been successfully developed to investigate folding kinetics of aptamers, while their co-transcriptional folding kinetics can be modeled by the helix-based computational method and BarMap approach. Based on the known aptamers, the web server Riboswitch Calculator and other theoretical methods provide a new tool to design synthetic riboswitches. This review will represent an overview of these computational methods for modeling structure and kinetics of riboswitch aptamers and for designing riboswitches.

Business model design for a wearable biofeedback system.

Science.gov (United States)

Hidefjäll, Patrik; Titkova, Dina

2015-01-01

Wearable sensor technologies used to track daily activities have become successful in the consumer market. In order for wearable sensor technology to offer added value in the more challenging areas of stress-rehab care and occupational health stress-related biofeedback parameters need to be monitored and more elaborate business models are needed. To identify probable success factors for a wearable biofeedback system (Affective Health) in the two mentioned market segments in a Swedish setting, we conducted literature studies and interviews with relevant representatives. Data were collected and used first to describe the two market segments and then to define likely feasible business model designs, according to the Business Model Canvas framework. Needs of stakeholders were identified as inputs to business model design. Value propositions, a key building block of a business model, were defined for each segment. The value proposition for occupational health was defined as "A tool that can both identify employees at risk of stress-related disorders and reinforce healthy sustainable behavior" and for healthcare as: "Providing therapists with objective data about the patient's emotional state and motivating patients to better engage in the treatment process".

Design information questionnaire for a model mixed oxide fuel fabrication facility

International Nuclear Information System (INIS)

Glancy, J.E.

1976-05-01

The model fuel plant is based on the proposed Westinghouse Anderson, S.C., plant and is typical of plants that will be constructed and operated in 1980 to 1990. A number of plant systems and procedures are uncertain, and in these cases judgment was used in describing relevant parameters in order to provide a complete model on which to design an inspection plan. The model plant does not, therefore, strictly represent any planned facility nor does it strictly represent the ideas of Westinghouse on plant design and material accountability. This report is divided into two sections. The first section is the IAEA Design Information Questionnaire form that contains an outline of all information requested. The second section is a complete listing of design information

Aerospace Activities in the Elementary School

Science.gov (United States)

Jones, Robert M.; Wiggins, Kenneth E.

1974-01-01

Describes 17 activities which are aerospace oriented and yet provide an interdisciplinary approach to learning. Some of the activities described involve paper airplanes, parachutes, model rockets, etc. (BR)

Design Modelling Symposium 2015

CERN Document Server

Tamke, Martin; Gengnagel, Christoph; Faircloth, Billie; Scheurer, Fabian

2015-01-01

This book reflects and expands on the current trend in the building industry to understand, simulate and ultimately design buildings by taking into consideration the interlinked elements and forces that act on them. This approach overcomes the traditional, exclusive focus on building tasks, while posing new challenges in all areas of the industry from material and structural to the urban scale. Contributions from invited experts, papers and case studies provide the reader with a comprehensive overview of the field, as well as perspectives from related disciplines, such as computer science. The chapter authors were invited speakers at the 5th Symposium "Modelling Behaviour", which took place at the CITA in Copenhagen in September 2015.

Sigma-delta modulator modeling analysis and design

International Nuclear Information System (INIS)

Ge Binjie; Wang Xin'an; Zhang Xing; Feng Xiaoxing; Wang Qingqin

2010-01-01

This paper introduces a new method for SC sigma-delta modulator modeling. It studies the integrator's different equivalent circuits in the integrating and sampling phases. This model uses the OP-AMP input pair's tail current (I 0 ) and overdrive voltage (v on ) as variables. The modulator's static and dynamic errors are analyzed. A group of optimized I 0 and v on for maximum SNR and power x area ratio can be obtained through this model. As examples, a MASH21 modulator for digital audio and a second order modulator for RFID baseband are implemented and tested, and they can achieve 91 dB and 72 dB respectively, which verifies the modeling and design criteria. (semiconductor integrated circuits)

A BIO-EXPERIENTIAL MODEL FOR LEARNING CREATIVE DESIGN PRACTICES THAT SUPPORTS TRANSFORMATIVE DEVELOPMENT IN BEGINNING DESIGN STUDENTS

Directory of Open Access Journals (Sweden)

Stephen Temple

2010-07-01

Full Text Available This paper asks what beginning design learning experiences best support the remainder of design education. It is a conjecture of brain-based learning theory that a student’s direct, concrete primary experiences are responsible for the construction of fundamental structures of neural processing as “hard wired” pathways. These structures then form the ground of and set into play patterns of later more abstracted learning experiences. Pedagogy of basic design courses that seeks introduction of creative processes as a foundation for design education must recognize these experiential, biologically developmental relationships as basic to developmentally appropriate beginning design curriculum. This paper models a beginning design pedagogy on developmental relationships between concrete and abstract processes of learning as a basis for transformative creative thinking that enables student self-development that progresses up the curriculum. Aligning with developmental learning theories (Piaget and others, a basic tenant of this approach is that learning at the primary level of direct experience self initiates brain changes where students form their own structure of learning. Thus, initial learning experiences will be those that best enable decision-making consistent with the biological interactivity between body and mind, between, respectively, the concrete and the abstract. This is important because the designed environment in which we all live is grounded in the development of abstract content experientially based in concrete material physicality. Experiential learning theories (Kolb and others, following Piaget identify concrete and abstract learning as fundamental poles for acquiring and acting on knowledge: Concrete learning involves direct experiential engagement through heuristic discovery and reflection and abstract learning involves indirect representational cues in acts of conceptualization, synthesis, and experimentation. The

Designing equivalent semantic models for process creation

NARCIS (Netherlands)

P.H.M. America (Pierre); J.W. de Bakker (Jaco)

1986-01-01

textabstractOperational and denotational semantic models are designed for languages with process creation, and the relationships between the two semantics are investigated. The presentation is organized in four sections dealing with a uniform and static, a uniform and dynamic, a nonuniform and

Application of Iterative Robust Model-based Optimal Experimental Design for the Calibration of Biocatalytic Models

DEFF Research Database (Denmark)

Van Daele, Timothy; Gernaey, Krist V.; Ringborg, Rolf Hoffmeyer

2017-01-01

The aim of model calibration is to estimate unique parameter values from available experimental data, here applied to a biocatalytic process. The traditional approach of first gathering data followed by performing a model calibration is inefficient, since the information gathered during...... experimentation is not actively used to optimise the experimental design. By applying an iterative robust model-based optimal experimental design, the limited amount of data collected is used to design additional informative experiments. The algorithm is used here to calibrate the initial reaction rate of an ω......-transaminase catalysed reaction in a more accurate way. The parameter confidence region estimated from the Fisher Information Matrix is compared with the likelihood confidence region, which is a more accurate, but also a computationally more expensive method. As a result, an important deviation between both approaches...

Modeling and design of X-rays bidimensional detectors

International Nuclear Information System (INIS)

Quisbert, Elmer Paz Alcon

2000-03-01

In this work has been developed the scintillating fiber optic and semiconductor devices based 2-D detector design, modeling and performance evaluation using Monte Carlo methods, for high X-ray energy range (10-140 kV) radiography and tomography applications. These processes allowed us, also, the imaging system parameters and components optimization and appropriate detector design. The model estimated the detectors performance parameters (DQE, MTF and SNR), and radiation risk (in terms of mean absorbed dose in the patient) and to show up how the sequence of physical processes in X-ray detection influence the performance of this imaging PFOC detectors. In this way, the modeling of the detector includes the statistics of the spatial distribution of absorbed X-rays and of X-ray to light conversion, its transmission, and the light quanta conversion into electrons. Also contributions to noise from the detection system chain is included, mainly the CCD detector ambient noise. Performance prediction, based on calculation taken from simulations, illustrates how such detectors meet the exacting requirements of some medical and industrial applications. Also, it is envisaged that our modeling procedure of the imaging system will be suitable not only for investigating how the system components should be best designed but for CT and RD system performance prediction. The powerful techniques would enable us to give advice for future development, in this field, in search of more dose-efficient imaging systems. (author)

Modeling and Simulation of the Second-Generation Orion Crew Module Air Bag Landing System

Science.gov (United States)

Timmers, Richard B.; Hardy, Robin C.; Willey, Cliff E.; Welch, Joseph V.

2009-01-01

Air bags were evaluated as the landing attenuation system for earth landing of the Orion Crew Module (CM). Analysis conducted to date shows that airbags are capable of providing a graceful landing of the CM in nominal and off-nominal conditions such as parachute failure, high horizontal winds, and unfavorable vehicle/ground angle combinations, while meeting crew and vehicle safety requirements. The analyses and associated testing presented here surround a second generation of the airbag design developed by ILC Dover, building off of relevant first-generation design, analysis, and testing efforts. In order to fully evaluate the second generation air bag design and correlate the dynamic simulations, a series of drop tests were carried out at NASA Langley s Landing and Impact Research (LandIR) facility in Hampton, Virginia. The tests consisted of a full-scale set of air bags attached to a full-scale test article representing the Orion Crew Module. The techniques used to collect experimental data, develop the simulations, and make comparisons to experimental data are discussed.

Concept Model For Designing Engaging And Motivating Games For Learning - The Smiley-Model

DEFF Research Database (Denmark)

Weitze, Charlotte Lærke; Ørngreen, Rikke

2012-01-01

The desire to use learning games in education is increasing, but the development of games for learning is still a growing field. Research shows that it remains difficult to develop learning games that are both instructive and engaging, although it is precisely the presence of these two elements...... that is believed to be an advantage when using learning games in education. In this paper the Smiley-model is presented (figure 1). The model describes which parameters and elements are important when designing a learning game. The present research is a result of a case-based action research study for designing...... a music learning game that teaches children to play piano using sheet music, and at the same time is fun and engaging. Although the model was originally developed for and through music, it has a more generic nature, and may be relevant for other fields as well. The Smiley-model is a condensed version...

Hippocampal closed-loop modeling and implications for seizure stimulation design

Science.gov (United States)

Sandler, Roman A.; Song, Dong; Hampson, Robert E.; Deadwyler, Sam A.; Berger, Theodore W.; Marmarelis, Vasilis Z.

2015-10-01

Objective. Traditional hippocampal modeling has focused on the series of feedforward synapses known as the trisynaptic pathway. However, feedback connections from CA1 back to the hippocampus through the entorhinal cortex (EC) actually make the hippocampus a closed-loop system. By constructing a functional closed-loop model of the hippocampus, one may learn how both physiological and epileptic oscillations emerge and design efficient neurostimulation patterns to abate such oscillations. Approach. Point process input-output models where estimated from recorded rodent hippocampal data to describe the nonlinear dynamical transformation from CA3 → CA1, via the schaffer-collateral synapse, and CA1 → CA3 via the EC. Each Volterra-like subsystem was composed of linear dynamics (principal dynamic modes) followed by static nonlinearities. The two subsystems were then wired together to produce the full closed-loop model of the hippocampus. Main results. Closed-loop connectivity was found to be necessary for the emergence of theta resonances as seen in recorded data, thus validating the model. The model was then used to identify frequency parameters for the design of neurostimulation patterns to abate seizures. Significance. Deep-brain stimulation (DBS) is a new and promising therapy for intractable seizures. Currently, there is no efficient way to determine optimal frequency parameters for DBS, or even whether periodic or broadband stimuli are optimal. Data-based computational models have the potential to be used as a testbed for designing optimal DBS patterns for individual patients. However, in order for these models to be successful they must incorporate the complex closed-loop structure of the seizure focus. This study serves as a proof-of-concept of using such models to design efficient personalized DBS patterns for epilepsy.

The effectiveness and efficiency of model driven game design

NARCIS (Netherlands)

Dormans, Joris

2012-01-01

In order for techniques from Model Driven Engineering to be accepted at large by the game industry, it is critical that the effectiveness and efficiency of these techniques are proven for game development. There is no lack of game design models, but there is no model that has surfaced as an industry

Architecture design in global and model-centric software development

NARCIS (Netherlands)

Heijstek, Werner

2012-01-01

This doctoral dissertation describes a series of empirical investigations into representation, dissemination and coordination of software architecture design in the context of global software development. A particular focus is placed on model-centric and model-driven software development.

Designing and redesigning medical telecare services: a forces-oriented model.

Science.gov (United States)

Gortzis, L G

2007-01-01

Medical telecare services' designing and redesigning still remains a challenging issue since it often depends on how a number of socio-technological issues are framed. This work has two key objectives; the former is to theoretically analyze the nature of a telecare environment by developing a model that reveals potential areas of analysis and the latter is to support designing and redesigning medical telecare services by formulating a strategy as well as a number of 'state of the art' guidelines. We have extended Leavitt's diamond to develop a model capable of accurately reflecting the telecare environment building dimensions as well as their interactions. This model depends on the i) technology, ii) collaborators, iii) tasks, iv) structure, v) social forces, and the vi) procedure dimensions. Taking this model as a core element we have proposed a service designing and redesigning strategy formulating, in parallel, six scalable dimension-oriented guidelines. During the two-year period (2003-2005) an enormous amount of data was collected (by active participating in two EU projects, by conducting semistructured interviews, by performing onsite observations as well as by reviewing 78 previous projects) and classified, structuring six guidelines. These guidelines can be considered as the 'state of the art' to support future services' design and redesign. This work considering the telecare environment as a multi-dimensional, operational organization has put the focus on accurate telecare services' design and redesign. The parameters are not limited, by any means, and are drawn from experience of designing services in a variety of telecare domains. The optimal parameter combination must be chosen according to the aim of each telecare procedure. Further research is needed to determine the minimum parameters to support telecare service design.

Adaptive Modeling, Engineering Analysis and Design of Advanced Aerospace Vehicles

Science.gov (United States)

Mukhopadhyay, Vivek; Hsu, Su-Yuen; Mason, Brian H.; Hicks, Mike D.; Jones, William T.; Sleight, David W.; Chun, Julio; Spangler, Jan L.; Kamhawi, Hilmi; Dahl, Jorgen L.

2006-01-01

This paper describes initial progress towards the development and enhancement of a set of software tools for rapid adaptive modeling, and conceptual design of advanced aerospace vehicle concepts. With demanding structural and aerodynamic performance requirements, these high fidelity geometry based modeling tools are essential for rapid and accurate engineering analysis at the early concept development stage. This adaptive modeling tool was used for generating vehicle parametric geometry, outer mold line and detailed internal structural layout of wing, fuselage, skin, spars, ribs, control surfaces, frames, bulkheads, floors, etc., that facilitated rapid finite element analysis, sizing study and weight optimization. The high quality outer mold line enabled rapid aerodynamic analysis in order to provide reliable design data at critical flight conditions. Example application for structural design of a conventional aircraft and a high altitude long endurance vehicle configuration are presented. This work was performed under the Conceptual Design Shop sub-project within the Efficient Aerodynamic Shape and Integration project, under the former Vehicle Systems Program. The project objective was to design and assess unconventional atmospheric vehicle concepts efficiently and confidently. The implementation may also dramatically facilitate physics-based systems analysis for the NASA Fundamental Aeronautics Mission. In addition to providing technology for design and development of unconventional aircraft, the techniques for generation of accurate geometry and internal sub-structure and the automated interface with the high fidelity analysis codes could also be applied towards the design of vehicles for the NASA Exploration and Space Science Mission projects.

Large scale solar district heating. Evaluation, modelling and designing

Energy Technology Data Exchange (ETDEWEB)

Heller, A.

2000-07-01

The main objective of the research was to evaluate large-scale solar heating connected to district heating (CSDHP), to build up a simulation tool and to demonstrate the application of the tool for design studies and on a local energy planning case. The evaluation of the central solar heating technology is based on measurements on the case plant in Marstal, Denmark, and on published and unpublished data for other, mainly Danish, CSDHP plants. Evaluations on the thermal, economical and environmental performances are reported, based on the experiences from the last decade. The measurements from the Marstal case are analysed, experiences extracted and minor improvements to the plant design proposed. For the detailed designing and energy planning of CSDHPs, a computer simulation model is developed and validated on the measurements from the Marstal case. The final model is then generalised to a 'generic' model for CSDHPs in general. The meteorological reference data, Danish Reference Year, is applied to find the mean performance for the plant designs. To find the expectable variety of the thermal performance of such plants, a method is proposed where data from a year with poor solar irradiation and a year with strong solar irradiation are applied. Equipped with a simulation tool design studies are carried out spreading from parameter analysis over energy planning for a new settlement to a proposal for the combination of plane solar collectors with high performance solar collectors, exemplified by a trough solar collector. The methodology of utilising computer simulation proved to be a cheap and relevant tool in the design of future solar heating plants. The thesis also exposed the demand for developing computer models for the more advanced solar collector designs and especially for the control operation of CSHPs. In the final chapter the CSHP technology is put into perspective with respect to other possible technologies to find the relevance of the application

Designing Experiments to Discriminate Families of Logic Models.

Science.gov (United States)

Videla, Santiago; Konokotina, Irina; Alexopoulos, Leonidas G; Saez-Rodriguez, Julio; Schaub, Torsten; Siegel, Anne; Guziolowski, Carito

2015-01-01

Logic models of signaling pathways are a promising way of building effective in silico functional models of a cell, in particular of signaling pathways. The automated learning of Boolean logic models describing signaling pathways can be achieved by training to phosphoproteomics data, which is particularly useful if it is measured upon different combinations of perturbations in a high-throughput fashion. However, in practice, the number and type of allowed perturbations are not exhaustive. Moreover, experimental data are unavoidably subjected to noise. As a result, the learning process results in a family of feasible logical networks rather than in a single model. This family is composed of logic models implementing different internal wirings for the system and therefore the predictions of experiments from this family may present a significant level of variability, and hence uncertainty. In this paper, we introduce a method based on Answer Set Programming to propose an optimal experimental design that aims to narrow down the variability (in terms of input-output behaviors) within families of logical models learned from experimental data. We study how the fitness with respect to the data can be improved after an optimal selection of signaling perturbations and how we learn optimal logic models with minimal number of experiments. The methods are applied on signaling pathways in human liver cells and phosphoproteomics experimental data. Using 25% of the experiments, we obtained logical models with fitness scores (mean square error) 15% close to the ones obtained using all experiments, illustrating the impact that our approach can have on the design of experiments for efficient model calibration.

Designing a framework to design a business model for the 'bottom of the pyramid' population

NARCIS (Netherlands)

Ver loren van Themaat, Tanye; Schutte, Cornelius S.L.; Lutters, Diederick

2013-01-01

This article presents a framework for developing and designing a business model to target the bottom of the pyramid (BoP) population. Using blue ocean strategy and business model literature, integrated with research on the BoP, the framework offers a systematic approach for organisations to analyse

Optimal closed-loop identification test design for internal model control

NARCIS (Netherlands)

Zhu, Y.; Bosch, van den P.P.J.

2000-01-01

In this work, optimal closed-loop test design for control is studied. Simple design formulas are derived based on the asymptotic theory of Ljung. The control scheme used is internal model control (IMC) and the design constraint is the power of the process output or that of the reference signal. The

Collaborative design for embedded systems co-modelling and co-simulation

CERN Document Server

Fitzgerald, John; Verhoef, Marcel

2014-01-01

This book presents a framework that allows the very different kinds of design models - discrete-event models of software and continuous time models of the physical environment - to be analyzed and simulated jointly, based on common scenarios.

Use of advanced modeling techniques to optimize thermal packaging designs.

Science.gov (United States)

Formato, Richard M; Potami, Raffaele; Ahmed, Iftekhar

2010-01-01

Through a detailed case study the authors demonstrate, for the first time, the capability of using advanced modeling techniques to correctly simulate the transient temperature response of a convective flow-based thermal shipper design. The objective of this case study was to demonstrate that simulation could be utilized to design a 2-inch-wall polyurethane (PUR) shipper to hold its product box temperature between 2 and 8 °C over the prescribed 96-h summer profile (product box is the portion of the shipper that is occupied by the payload). Results obtained from numerical simulation are in excellent agreement with empirical chamber data (within ±1 °C at all times), and geometrical locations of simulation maximum and minimum temperature match well with the corresponding chamber temperature measurements. Furthermore, a control simulation test case was run (results taken from identical product box locations) to compare the coupled conduction-convection model with a conduction-only model, which to date has been the state-of-the-art method. For the conduction-only simulation, all fluid elements were replaced with "solid" elements of identical size and assigned thermal properties of air. While results from the coupled thermal/fluid model closely correlated with the empirical data (±1 °C), the conduction-only model was unable to correctly capture the payload temperature trends, showing a sizeable error compared to empirical values (ΔT > 6 °C). A modeling technique capable of correctly capturing the thermal behavior of passively refrigerated shippers can be used to quickly evaluate and optimize new packaging designs. Such a capability provides a means to reduce the cost and required design time of shippers while simultaneously improving their performance. Another advantage comes from using thermal modeling (assuming a validated model is available) to predict the temperature distribution in a shipper that is exposed to ambient temperatures which were not bracketed

Reactor design, cold-model experiment and CFD modeling for chemical looping combustion

Energy Technology Data Exchange (ETDEWEB)

Zhang, Shaohua; Ma, Jinchen; Hu, Xintao; Zhao, Haibo; Wang, Baowen; Zheng, Chuguang [Huazhong Univ. of Science and Technology, Wuhan (China). State Key Lab. of Coal Combustion

2013-07-01

Chemical looping combustion (CLC) is an efficient, clean and cheap technology for CO{sub 2} capture, and an interconnected fluidized bed is more appropriate solution for CLC. This paper aims to design a reactor system for CLC, carry out cold-model experiment of the system, and model fuel reactor using commercial CFD software. As for the CLC system, the air reactor (AR) is designed as a fast fluidized bed while the fuel reactor (FR) is a bubbling bed; a cyclone is used for solid separation of the AR exit flow. The AR and FR are separated by two U-type loop seals to remain gas sealed. Considered the chemical kinetics of oxygen carrier, fluid dynamics, pressure balance and mass balance of the system simultaneously, some key design parameters of a CH{sub 4}-fueled and Fe{sub 2}O{sub 3}/Al{sub 2}O{sub 3}-based CLC reactor (thermal power of 50 kWth) are determined, including key geometric parameters (reactor cross-sectional area and reactor height) and operation parameters (bed material quantity, solid circulation rate, apparent gas velocity of each reactor). A cold-model bench having same geometric parameters with its prototype is built up to study the effects of various operation conditions (including gas velocity in the reactors and loop seals, and bed material height, etc.) on the solids circulation rate, gas leakage, and pressure balance. It is witnessed the cold-model system is able to meet special requirements for CLC system such as gas sealing between AR and FR, the circulation rate and particles residence time. Furthermore, the thermal FR reactor with oxygen carrier of Fe{sub 2}O{sub 3}/Al{sub 2}O{sub 3} and fuel of CH{sub 4} is simulated by commercial CFD solver FLUENT. It is found that for the design case the combustion efficiency of CH{sub 4} reaches 88.2%. A few part of methane is unburned due to fast, large bubbles rising through the reactor.

The impact of pharmacophore modeling in drug design.

Science.gov (United States)

Guner, Osman F

2005-07-01

With the reliable use of computer simulations in scientific research, it is possible to achieve significant increases in productivity as well as a reduction in research costs compared with experimental approaches. For example, computer-simulation can substantially enchance productivity by focusing the scientist to better, more informed choices, while also driving the 'fail-early' concept to result in a significant reduction in cost. Pharmacophore modeling is a reliable computer-aided design tool used in the discovery of new classes of compounds for a given therapeutic category. This commentary will briefly review the benefits and applications of this technology in drug discovery and design, and will also highlight its historical evolution. The two most commonly used approaches for pharmacophore model development will be discussed, and several examples of how this technology was successfully applied to identify new potent leads will be provided. The article concludes with a brief outline of the controversial issue of patentability of pharmacophore models.

Collapsing Factors in Multitrait-Multimethod Models: Examining Consequences of a Mismatch Between Measurement Design and Model

Directory of Open Access Journals (Sweden)

Christian eGeiser

2015-08-01

Full Text Available Models of confirmatory factor analysis (CFA are frequently applied to examine the convergent validity of scores obtained from multiple raters or methods in so-called multitrait-multimethod (MTMM investigations. Many applications of CFA-MTMM and similarly structured models result in solutions in which at least one method (or specific factor shows non-significant loading or variance estimates. Eid et al. (2008 distinguished between MTMM measurement designs with interchangeable (randomly selected versus structurally different (fixed methods and showed that each type of measurement design implies specific CFA-MTMM measurement models. In the current study, we hypothesized that some of the problems that are commonly seen in applications of CFA-MTMM models may be due to a mismatch between the underlying measurement design and fitted models. Using simulations, we found that models with M method factors (where M is the total number of methods and unconstrained loadings led to a higher proportion of solutions in which at least one method factor became empirically unstable when these models were fit to data generated from structurally different methods. The simulations also revealed that commonly used model goodness-of-fit criteria frequently failed to identify incorrectly specified CFA-MTMM models. We discuss implications of these findings for other complex CFA models in which similar issues occur, including nested (bifactor and latent state-trait models.

On the use of dynamic modelling for the design of IRF

International Nuclear Information System (INIS)

Hinds, H.W.

1997-01-01

The multi-purpose high-flux Irradiation Research Facility (IRF) reactor has been proposed by AECL as a replacement for the venerable NRU reactor at Chalk River, and the pre-project design of IRF is currently underway. As part of this design effort, we are currently modelling the dynamic response of the reactor and especially that of the Reactor Regulating System (RRS). The tool chosen for this work is the MATRIXx family of programs, including XMath, SystemBuild and DocumentIt. The SystemBuild tool allows users to specify a complete model by graphically interconnecting a set of modules (SuperBlocks) and/or 'primitives'. Each module, in turn, can be defined graphically by interconnecting a further set of sub-modules and/or 'primitives'. The system supports both continuous (analog) as well as discrete (digital) modules at the same time. Thus, it is possible to accurately model a continuous process coupled to its computer-based control system. The frequency response of the system can be extracted from the same model. The model will be used for control system stability analysis and to choose appropriate design parameters for various controllers and dynamic compensators within both the RRS and other important controllers in the system. The whole system can then be tested using various manoeuvres such as start-ups, shutdowns and step perturbations. It can also be used to verify that the design functions well under extreme conditions such as those which might occur at the beginning or end of the fuel cycle, or when attempting to override a poison-out. The model can also be of practical assistance to other designers in choosing the various parameters involved (e.g., step size of the stepping motor drives for the control absorber rods (CARs), or rundown time of the main primary coolant system pumps). The model currently consists of: point- or 7-node neutron kinetics with temperature and xenon feedback; 1 or 2 sets of log, linear and log rate amplifiers; the RRS (flux

Analytical model for Stirling cycle machine design

Energy Technology Data Exchange (ETDEWEB)

Formosa, F. [Laboratoire SYMME, Universite de Savoie, BP 80439, 74944 Annecy le Vieux Cedex (France); Despesse, G. [Laboratoire Capteurs Actionneurs et Recuperation d' Energie, CEA-LETI-MINATEC, Grenoble (France)

2010-10-15

In order to study further the promising free piston Stirling engine architecture, there is a need of an analytical thermodynamic model which could be used in a dynamical analysis for preliminary design. To aim at more realistic values, the models have to take into account the heat losses and irreversibilities on the engine. An analytical model which encompasses the critical flaws of the regenerator and furthermore the heat exchangers effectivenesses has been developed. This model has been validated using the whole range of the experimental data available from the General Motor GPU-3 Stirling engine prototype. The effects of the technological and operating parameters on Stirling engine performance have been investigated. In addition to the regenerator influence, the effect of the cooler effectiveness is underlined. (author)

Improving the Aircraft Design Process Using Web-based Modeling and Simulation

Science.gov (United States)

Reed, John A.; Follen, Gregory J.; Afjeh, Abdollah A.

2003-01-01

Designing and developing new aircraft systems is time-consuming and expensive. Computational simulation is a promising means for reducing design cycle times, but requires a flexible software environment capable of integrating advanced multidisciplinary and muitifidelity analysis methods, dynamically managing data across heterogeneous computing platforms, and distributing computationally complex tasks. Web-based simulation, with its emphasis on collaborative composition of simulation models, distributed heterogeneous execution, and dynamic multimedia documentation, has the potential to meet these requirements. This paper outlines the current aircraft design process, highlighting its problems and complexities, and presents our vision of an aircraft design process using Web-based modeling and simulation.

Thermal modeling of nuclear waste package designs for disposal in tuff

International Nuclear Information System (INIS)

Hockman, J.N.; O'Neal, W.C.

1983-09-01

Lawrence Livermore National Laboratory is involved in the design and testing of high-level nuclear waste packages. Many of the aspects of waste package design and testing (e.g., corrosion and leaching) depend in part on the temperature history of the emplaced packages. This paper discusses thermal modeling and analysis of various emplaced waste package conceptual designs including the models used, the assumptions and approximations made, and the results obtained. 6 references, 6 figures, 3 tables

Thermal modeling of nuclear waste package designs for disposal in tuff

International Nuclear Information System (INIS)

Hockman, J.N.; O'Neal, W.C.

1984-02-01

Lawrence Livermore National Laboratory is involved in the design and testing of high-level nuclear waste packages. Many of the aspects of waste package design and testing (e.g., corrosion and leaching) depend in part on the temperature history of the emplaced packages. This paper discusses thermal modeling and analysis of various emplaced waste package conceptual designs including the models used, the assumptions and approximations made, and the results obtained. 6 references, 6 figures, 4 tables

New model performance index for engineering design of control systems

Science.gov (United States)

1970-01-01

Performance index includes a model representing linear control-system design specifications. Based on a geometric criterion for approximation of the model by the actual system, the index can be interpreted directly in terms of the desired system response model without actually having the model's time response.

Probabilistic predictive modelling of carbon nanocomposites for medical implants design.

Science.gov (United States)

Chua, Matthew; Chui, Chee-Kong

2015-04-01

Modelling of the mechanical properties of carbon nanocomposites based on input variables like percentage weight of Carbon Nanotubes (CNT) inclusions is important for the design of medical implants and other structural scaffolds. Current constitutive models for the mechanical properties of nanocomposites may not predict well due to differences in conditions, fabrication techniques and inconsistencies in reagents properties used across industries and laboratories. Furthermore, the mechanical properties of the designed products are not deterministic, but exist as a probabilistic range. A predictive model based on a modified probabilistic surface response algorithm is proposed in this paper to address this issue. Tensile testing of three groups of different CNT weight fractions of carbon nanocomposite samples displays scattered stress-strain curves, with the instantaneous stresses assumed to vary according to a normal distribution at a specific strain. From the probabilistic density function of the experimental data, a two factors Central Composite Design (CCD) experimental matrix based on strain and CNT weight fraction input with their corresponding stress distribution was established. Monte Carlo simulation was carried out on this design matrix to generate a predictive probabilistic polynomial equation. The equation and method was subsequently validated with more tensile experiments and Finite Element (FE) studies. The method was subsequently demonstrated in the design of an artificial tracheal implant. Our algorithm provides an effective way to accurately model the mechanical properties in implants of various compositions based on experimental data of samples. Copyright © 2015 Elsevier Ltd. All rights reserved.

Application of Simple CFD Models in Smoke Ventilation Design

DEFF Research Database (Denmark)

Brohus, Henrik; Nielsen, Peter Vilhelm; la Cour-Harbo, Hans

2004-01-01

The paper examines the possibilities of using simple CFD models in practical smoke ventilation design. The aim is to assess if it is possible with a reasonable accuracy to predict the behaviour of smoke transport in case of a fire. A CFD code mainly applicable for “ordinary” ventilation design...

Role of modeling in the design of experiments in carbohydrate metabolism

International Nuclear Information System (INIS)

Foster, D.M.; Hetenyi, G. Jr.

1991-01-01

Most publications on modeling present only the final product without describing the details as to how they were developed and tested. It is, however, by model development and testing that the true power of modeling as a research tool reveals itself. The purpose of this paper is to present a behind the scenes look at a set of experiments designed to study carbon atom transport in gluconeogenesis. In particular, it will be shown how the development of one model led to hypotheses for which another set of experiments was designed. The model which resulted from the second study contained in turn a number of new hypotheses for which further experiments remain to be designed. The second model supported the findings of the first, and yielded deeper insights into the exchange of carbon atoms among three metabolites. It is hoped this illustration will encourage other investigators to take advantage of the utilitarian value of modeling not only as a parameter generating tool, but also as a true research tool which can aid significantly to extract more information from available data

Conceptual models in man-machine design verification

International Nuclear Information System (INIS)

Rasmussen, J.

1985-01-01

The need for systematic methods for evaluation of design concepts for new man-machine systems has been rapidly increasing in consequence of the introduction of modern information technology. Direct empirical methods are difficult to apply when functions during rare conditions and support of operator decisions during emergencies are to be evaluated. In this paper, the problems of analytical evaluations based on conceptual models of the man-machine interaction are discussed, and the relations to system design and analytical risk assessment are considered. Finally, a conceptual framework for analytical evaluation is proposed, including several domains of description: 1. The problem space, in the form of a means-end hierarchy; 2. The structure of the decision process; 3. The mental strategies and heuristics used by operators; 4. The levels of cognitive control and the mechanisms related to human errors. Finally, the need for models representing operators' subjective criteria for choosing among available mental strategies and for accepting advice from intelligent interfaces is discussed

Review of SFR Design Safety using Preliminary Regulatory PSA Model

International Nuclear Information System (INIS)

Na, Hyun Ju; Lee, Yong Suk; Shin, Andong; Suh, Nam Duk

2013-01-01

The major objective of this research is to develop a risk model for regulatory verification of the SFR design, and thereby, make sure that the SFR design is adequate from a risk perspective. In this paper, the development result of preliminary regulatory PSA model of SFR is discussed. In this paper, development and quantification result of preliminary regulatory PSA model of SFR is discussed. It was confirmed that the importance PDRC and ADRC dampers is significant as stated in the result of KAERI PSA model. However, the importance can be changed significantly depending on assumption of CCCG and CCF factor of PDRC and ADRC dampers. SFR (sodium-cooled fast reactor) which is Gen-IV nuclear energy system, is designed to accord with the concept of stability, sustainability and proliferation resistance. KALIMER-600, which is under development in Korea, includes passive safety systems (e. g. passive reactor shutdown, passive residual heat removal, and etc.) as well as active safety systems. Risk analysis from a regulatory perspective is needed to support the regulatory body in its safety and licensing review for SFR (KALIMER-600). Safety issues should be identified in the early design phase in order to prevent the unexpected cost increase and delay of the SFR licensing schedule that may be caused otherwise

Intraocular Telescopic System Design: Optical and Visual Simulation in a Human Eye Model

OpenAIRE

Zoulinakis, Georgios; Ferrer-Blasco, Teresa

2017-01-01

Purpose. To design an intraocular telescopic system (ITS) for magnifying retinal image and to simulate its optical and visual performance after implantation in a human eye model. Methods. Design and simulation were carried out with a ray-tracing and optical design software. Two different ITS were designed, and their visual performance was simulated using the Liou-Brennan eye model. The difference between the ITS was their lenses’ placement in the eye model and their powers. Ray tracing in bot...

Underwater striling engine design with modified one-dimensional model

Directory of Open Access Journals (Sweden)

Daijin Li

2015-05-01

Full Text Available Stirling engines are regarded as an efficient and promising power system for underwater devices. Currently, many researches on one-dimensional model is used to evaluate thermodynamic performance of Stirling engine, but in which there are still some aspects which cannot be modeled with proper mathematical models such as mechanical loss or auxiliary power. In this paper, a four-cylinder double-acting Stirling engine for Unmanned Underwater Vehicles (UUVs is discussed. And a one-dimensional model incorporated with empirical equations of mechanical loss and auxiliary power obtained from experiments is derived while referring to the Stirling engine computer model of National Aeronautics and Space Administration (NASA. The P-40 Stirling engine with sufficient testing results from NASA is utilized to validate the accuracy of this one-dimensional model. It shows that the maximum error of output power of theoretical analysis results is less than 18% over testing results, and the maximum error of input power is no more than 9%. Finally, a Stirling engine for UUVs is designed with Schmidt analysis method and the modified one-dimensional model, and the results indicate this designed engine is capable of showing desired output power.

Inspired by design and driven by innovation. A conceptual model for radical design driven as a sustainable business model for Malaysian furniture design

Science.gov (United States)

Yusof, Wan Zaiyana Mohd; Fadzline Muhamad Tamyez, Puteri

2018-04-01

The definition of innovation does not help the entrepreneurs, business person or innovator to truly grasp what it means to innovate, hence we hear that government has spend millions of ringgit on “innovation” by doing R & D. However, the result has no avail in terms of commercial value. Innovation can be defined as the exploitation of commercialization of an idea or invention to create economic or social value. Most Entrepreneurs and business managers, regard innovation as creating economic value, while forgetting that innovation also create value for society or the environment. The ultimate goal as Entrepreneur, inventor or researcher is to exploit innovation to create value. As changes happen in society and economy, organizations and enterprises have to keep up and this requires innovation. This conceptual paper is to study the radical design driven innovation in the Malaysian furniture industry as a business model which the overall aim of the study is to examine the radical design driven innovation in Malaysia and how it compares with findings from Western studies. This paper will familiarize readers with the innovation and describe the radical design driven perspective that is adopted in its conceptual framework and design process.

Optimizing incomplete sample designs for item response model parameters

NARCIS (Netherlands)

van der Linden, Willem J.

Several models for optimizing incomplete sample designs with respect to information on the item parameters are presented. The following cases are considered: (1) known ability parameters; (2) unknown ability parameters; (3) item sets with multiple ability scales; and (4) response models with

Research on PCPV for BWR - physical model as design tool - main results

International Nuclear Information System (INIS)

Fumagalli, E.; Verdelli, G.

1975-01-01

ISMES (Experimental Institute for Models and Structures) is now carrying out a series of tests on physical models as a part of a research programme sponsored by DSR (Studies and Research Direction) of ENEL (Italian State Electricity Board) on behalf of CPN (Nuclear Design and Construction Centre) of ENEL with the aim to experience a 'Thin'-walled PCPV for 'BWR'. The physical model, together with the mathematical model and the rheological model of the materials, is intended as a meaningful design tool. The mathematical model covers the overall structural design phase, (geometries) and the linear behaviour, whereas the physical model, besides of a global information to be compared with the results of the mathematical model, supplies a number of data as the non-linear behaviour up to failure and local conditions (penetration area etc.) are concerned. The aim of the first phase of this research programme is to make a comparison between the calculation and experiment tests as the thicknesses of the wall and the bottom slab are concerned, whereas the second phase of the research deals with the behaviour of the removable lid and its connection with the main structure. To do this, a model in scale 1:10 has been designed which symmetrically reproduces with respect to the equator, the bottom part of the structure. In the bottom slab the penetrations of the prototype design are reproduced, whereas the upper slab is plain. This paper describes the model, and illustrates the main results, underlining the different behaviour of the upper and bottom slabs up to collapse

An Extended Kalman filter (EKF) for Mars Exploration Rover (MER) entry, descent, and landing reconstruction

Science.gov (United States)