WorldWideScience

Sample records for mochiita kahen funko

  1. Injection and spray characteristics of a variable orifice nozzle applied the jerk type fuel injection pump for DI diesel engine; Jerk shiki nenryo funsha pump wo mochiita kahen funko nozzle no funsha funmu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, T; Matsui, K; Iwasaki, T; Kobayashi, T [Zexel Corp., Tokyo (Japan); Matsumoto, Y [The University of Tokyo, Tokyo (Japan)

    1997-10-01

    A Variable Orifice Nozzle (VON) by changing a cross-sectional area of the nozzle injection hole, for improving a rate of injection and injection duration, has been developed to study its injection and spray characteristics. The nozzle geometry was optimized to analyze a nozzle internal flow by computational method. Results show that, injection and spray pattern responded to the nozzle orifice cross-sectional area which is changing larger to smaller in the part load range. This results suggest to contribute a combustion improvement which decreasing NOx and soot. 14 refs., 10 figs.

  2. Improvement of combustion in a direct injection diesel engine by the use of a combustion-hole injection nozzle; Kumiawase funko nozzle ni yoru chokusetsu funshashiki diesel engine no nensho kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Shoji, T. [Mitsubishi Motors Corp., Tokyo (Japan); Kamimoto, T. [Tokyo Institute of Technology, Tokyo (Japan)

    1998-04-25

    Suppression of pre-mixed combustion and activation of diffusion combustion in DI diesel engines are known to be effective in reducing both NOx and fuel consumption. To achieve this concept, the authors have proposed a new type of fuel injection nozzle named combination-hole nozzle. This nozzle has very small holes with a diameter of 0.13 mm below (sub holes) for reducing ignition delay and normal holes (main holes) for keeping reasonable injection duration. The experiments conducted with a single cylinder research engine revealed that the combination-hole nozzle reduced the ignition delay and the peak value of the rate of heat release during the premixed combustion by 10% and 40% respectively compared with the experimental results of conventional nozzles and that the trade-off curve between NOx and fuel consumption sifted to the low level corner at half and full load conditions at a low engine speed. The reason for this improvement was investigated by the measurement of flame temperature distribution in the combustion chamber by means of the two colors method. The result revealed that the flame temperature in regions between sub and main hole`s flames of the nozzle was lower than that of the flames of a conventional nozzle at a full load and a low speed condition. 13 refs., 10 figs., 3 tabs.

  3. Eesti tudengid välismaale õpetajaks / Helen Uldrich

    Index Scriptorium Estoniae

    Uldrich, Helen

    2006-01-01

    Tudengiprojekti "Include Me" pakub kahenädalst õpetajapraktikat välismaal. Tallinna koolidesse saabusid õpetajapraktikale noored Saksamaalt, Belgiast ja Hollandist. Eelmisel aastal käisid Tallinna Ülikooli tudengid Belgias ja Saksamaal õpetajapraktikal

  4. Kunstnike töötsoon Colina Lab / Merit Kask

    Index Scriptorium Estoniae

    Kask, Merit

    2006-01-01

    Kahenädalane kunstilaboratoorium Tallinnas Kanuti Gildi saalis; kus loomingulistel aladel tegutsevad kunstnikud arendasid kõikvõimalikke projekte neljas rühmas. Kuraator Silke Bake valis osalema 19 kunstnikku Eestist, Saksamaalt, Portugalist, Taanist, Inglismaalt, Prantsusmaalt

  5. "Master i Margarita" - teatralnõi roman? / Susanna Witt

    Index Scriptorium Estoniae

    Witt, Susanna

    1998-01-01

    Bibl. lk. 316. Kokkuvõte inglise k. "Master and Margarita - a theatrical novel?". ""Meister ja Margarita" - teatriromaan?". Mihhail Bulgakovi romaani "Meister ja Margarita" kahene struktuur ja ukraina rahvuslik nukuteater vertep

  6. New seismic source `BLASTER` for seismic survey; Hasaiyaku wo shingen to shite mochiita danseiha tansa

    Energy Technology Data Exchange (ETDEWEB)

    Koike, G; Yoshikuni, Y [OYO Corp., Tokyo (Japan)

    1996-10-01

    Built-up weight and vacuole have been conceived as seismic sources without using explosive. There have been problems that they have smaller energy to generate elastic wave than explosive, and that they have inferior working performance. Concrete crushing explosive is tried to use as a new seismic source. It is considered to possess rather large seismic generating energy, and it is easy to handle from the viewpoint of safety. Performance as seismic source and applicability to exploration works of this crushing explosive were compared with four kinds of seismic sources using dynamite, dropping weight, shot-pipe utilizing shot vacuole, and impact by wooden maul. When considered by the velocity amplitude, the seismic generating energy of the crushing explosive of 120 g is about one-fifth of dynamite of 100 g. Elastic wave generated includes less high frequency component than that by dynamite, and similar to that using seismic source without explosive, such as the weight dropping. The maximum seismic receiving distance obtained by the seismic generation was about 100 m. This was effective for the slope survey with the exploration depth between 20 m and 30 m. 1 ref., 9 figs., 2 tabs.

  7. Electrophoretic display using microencapsulated suspension; Maikuro kapuseru ka bunsaneki wo mochiita denki eido deisupurei

    Energy Technology Data Exchange (ETDEWEB)

    Kawai, H. [NOK Corp., Tokyo (Japan)

    1999-11-01

    Electrophoretic display (EPD) is a non-luminous type display using electrophoresis of particles dispersing in a solvent. This kind of display is particularly good at displaying like printing matters. By micro-encapsulating the dispersion medium, a realization of the thin and flexible display device become possible. Further, an EPD (MC-EPD) using a microencapsulated suspension is a forceful candidate for realizing digital paper in the future. In this paper, principle and characteristics of the EPD are explained and application to rewritable sheet (MC-EPS) is introduced. MC-EPS is a rewritable sheet-like display formed by coating a flexible base material such as a polymer film or paper with microcapsules and applying an electric field from external. As an electrostatic latent image formation technique in the electro photography field can be applied as a voltage impression method, the development of the special writing equipment is unnecessary. (NEDO)

  8. Thermorewritable card by using dyes; Senryo wo mochiita kakikae kanona card

    Energy Technology Data Exchange (ETDEWEB)

    Muto, Y.

    1998-06-01

    Described herein are thermorewritable cards which use dyes. Rewritable cards, mainly used for membership and point cards, are themselves used repeatedly and required to be rewritable repeatedly for information they carry. The dyes and developers used for the conventional heat- and pressure-sensitive papers are colorless, leuco-dye precursors and acidic compounds with a phenolic hydroxyl group or the like. They transfer electrons to each other, opening the lactone ring of the dye precursor to develop the color. Developing and erasing the color are reversible chemical reactions, where the color is developed under heat and maintained by quenching. For erasing the color, it is heated and then slowly cooled to separate the precursor and developer phases from each other. A printer (thermal head) is required for developing and erasing a color. Durability under various conditions is another requirement of the card; it must be adaptable to weather conditions and resistant to sweat. The new thermorewritable card is protected from various adverse effects on its chemical reactions, and made as durable as the conventional cards. 3 refs., 5 figs., 1 tab.

  9. Shallow PS-logging by high frequency wave; Koshuha wo mochiita senbu PS kenso

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, A; Miyazawa, M; Azuma, H [OYO Corp., Tokyo (Japan)

    1996-05-01

    This paper describes the following matters on down-hole PS logging in shallow subsurface. Determining an elastic wave velocity structure in shallow subsurface with high accuracy by using down-hole PS logging requires reduction of errors in reading travel time. Therefore, a high-frequency vibration source was fabricated with an objective to raise frequencies of waves used for the measurement. Measurements were made on two holes, A and B, at a measurement interval of 0.5 m, whereas at the hole A a measurement was performed simultaneously by using a normal type (low-frequency) vibration source. A spectral analysis on the waveform record revealed that the frequencies with each vibration source were 127 Hz and 27 Hz for the hole A, 115 Hz for the hole B, and the S/N ratio was all the same for both holes. When the high-frequency vibration source was used, the velocity was determined at accuracy of 5% over the whole length of the shallow section. When the low-frequency vibration source was used, sections with the velocity determining error greater than 5% were found, and it was not possible to derive the velocity structure in the shallow subsurface in fine segments. 3 refs., 8 figs., 2 tabs.

  10. Robust optimum design with maximum entropy method; Saidai entropy ho mochiita robust sei saitekika sekkeiho

    Energy Technology Data Exchange (ETDEWEB)

    Kawaguchi, K; Egashira, Y; Watanabe, G [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    Vehicle and unit performance change according to not only external causes represented by the environment such as temperature or weather, but also internal causes which are dispersion of component characteristics and manufacturing processes or aged deteriorations. We developed the design method to estimate thus performance distributions with maximum entropy method and to calculate specifications with high performance robustness using Fuzzy theory. This paper describes the details of these methods and examples applied to power window system. 3 refs., 7 figs., 4 tabs.

  11. Field tests of electric survey using capacitive electrodes; Kyapashita denkyoku wo mochiita denki tansarei

    Energy Technology Data Exchange (ETDEWEB)

    Miyazaki, I; Iseki, S; Kobayashi, T [OYO Corp., Tokyo (Japan)

    1997-10-22

    This paper describes field test results of electric survey using capacitive electrodes. When two metal plates are approached without contacting with the ground and voltage is applied between the plates, current flows in the ground. The metal plates and the ground work as a capacitor. Charges are stored between them. These metal plates having insulation with the ground are called capacitive electrodes. When ac voltage is applied between a pair of capacitors, current flows continuously in the ground without saturating the capacitors. Resistivity of the ground can be determined by measuring the level of current flowing in the ground and the level of potential. As a result of the field tests, it was found that the present method is superior to the conventional method in around ten times. However, to obtain high quality data, water spraying, reduced towing speed at the low resistivity ground such as clay and soil, and grass mowing are required. 3 refs., 5 figs., 1 tab.

  12. Measurement of sea ice thickness using electromagnetic sounding; Denji tansaho wo mochiita kaihyoatsu no keisoku

    Energy Technology Data Exchange (ETDEWEB)

    Kawauchi, K; Suzuki, I; Goto, N [Muroran Institute of Technology, Hokkaido (Japan); Hoshiyama, K

    1997-10-22

    Thickness of sea ice is measured by an electromagnetic method making use of the peculiarities of sea ice. Sea ice floats on the seawater (saline water), and the result is two horizontal layers greatly different from each other in conductivity, with seawater being highly conductive and ice being non-conductive. A study is conducted on Lake Kumatori, a saline lake in Abashiri City, in which effort a board of naturally frozen sea ice and a board of sea ice allowed to form on the sea surface at a spot from which ice has been removed are examined. A portable electromagnetic probe EM38 of GEONICS Company is employed to perform measurement in a horizontal dipole mode. To determine the relationship between the obtained conductivity measurements and sea ice thickness, holes are bored in the sea ice boards for the measurement of their thickness for the formulation of an experimental regression equation. Measurements along the traverse line 1 and traverse line 3 are converted into sea ice thickness by use of the experimental regression equation, and the result is that ice thickness is the greatest near the quay growing thinner away from the shore. The study shows that sea ice thickness may be measured accurately by electromagnetic probing. 3 refs., 10 figs.

  13. Soil surveying using electromagnetic methods; Denji tansaho wo mochiita jiban chosa

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, I; Kawauchi, K; Goto, N [Muroran Institute of Technology, Hokkaido (Japan); Takahashi, N; Yamada, T [Zukohsya Co. Ltd., Hokkaido (Japan)

    1997-10-22

    Electromagnetic surveying method is applied in Muroran Institute of Technology`s site for power transmission steel towers for the locating of structures buried in the ground and for the study of obstruction to the application of the method. The devices employed are the EM31 and EM38 which are portable conductivity measuring instruments manufactured by GEONICS Company. With the probeable depth in the horizontal dipole mode being approximately half that in the vertical dipole mode, depths of 0.5m, 1m, 3m, and 6m may be explored using the two instruments. In the measurement test, the devices are used to determine a reinforced concrete-made multi-purpose duct that accommodates water pipes, sewers, various electric wires, and heating pipes and is buried at a depth of 2-3m in the ground. In the measurement for a 3m-deep level, a spot high in conductivity due to the reinforced concrete is detected, and the result roughly corresponds to the lay of the duct. In the measurement for a 6m-deep level, no high-conductivity spot is found, meaning there is no such structure at this depth. Although there are some other high conductivity values recorded, they are attributed to manhole covers or steel tower bases on the ground surface. 3 refs., 8 figs.

  14. Preparation of minute particle using supercritical fluid; Chorinkai ryutai wo mochiita biryushi no chosei

    Energy Technology Data Exchange (ETDEWEB)

    Ajiri, T [Tohoku University, Sendai (Japan). Faculty of Engineering

    1995-03-05

    The metal oxide minute particle synthesis method according to the water-heat reaction in supercritical water was described. Metal salt liquid solution was subjected to hydrolysis when heated to become metal hydroxide but dehydration reaction was generated at a high temperature to generate metal oxide minute particle. Metal salt aqueous solution was supplied to a circulation system unit to contact heated water and was rapidly heated to supercritical state and then was subjected to hydrolysis/dehydration reaction, thus continuously collecting metal oxide minute particles. The hydrolysis speed was in first order for the metal ion concentration and the reaction speed was accelerated by several tens of times when entering supercritical region from subcritical region. When the temperature was rapidly increased to the supercritical state, a radical hydrolysis was generated and a high saturation was instantly reached and minute particles tended to be generated easily since the dissolution force of supercritical water for a product was small. A minute particle with a crystallizability of 5 nm was obtained by synthesizing ceria super-minute particle which was the abrasive of an optical glass material. A single phase of a high magnetization characteristic was synthesized continuously and quickly (faster than a conventional method by two orders or more) in the continuous synthesis of Ba ferrite as a magnetic recording material. 12 refs., 3 figs., 1 tab.

  15. Biodegradable polymeric foam with food waste; Shokumotsu zansa wo mochiita seibunkai kobunshi hahhotai

    Energy Technology Data Exchange (ETDEWEB)

    Mishima, Kenji; Matsuyama, Kiyoshi; Yamauchi, Satoru; Takarabe, Shin' ichi

    1999-09-01

    A huge amount of food waste such as tea and beer dregs becomes a serious problem because of the lack of industrial waste space in Japan. On the other hand, the new polymeric foam is expected to be developed since the dangerous pollution of endorphin disrupters from industrial polymer foam is pointed out. In this work, we try to develop the biodegradable polymeric foam using the tea and beer dregs as secondary resources. And we examined the degradability of biodegradable polymer in the hydrothermal water for fundamental knowledge of polymeric foam production. We used an extruder equipped with a high pressure device to make the polymeric foam. And we examined the effect of the component ratio on the foam properties, foaming rate, strength, shrinkage rate, water-resistant. As a result, it was found that the amount of polymer is effective of quality of form and the biodegradability can be controlled by the amount of water and temperature. (author)

  16. Dioxin sensing which uses fluorescent cyclodextrin; Keikosei shikurodekisutorin wo mochiita daiokishin senshingu

    Energy Technology Data Exchange (ETDEWEB)

    Hamada, F. [Akita Univ., Akita (Japan)

    2000-05-01

    Environmental hormones are called pluricausal endocrine disrupting chemical substances (endocrine disrupters) that are deemed to disrupt effects of vital hormones and give influence to homeostasis of in vivo environment. Today, 70,000 to 80,000 kinds of chemical substances are used in the world, and about 70 kinds among them are suspected of being environmental hormones. The present authors have clarified that a host with fluorescent residue chemically bonded to cyclodextrin responses at a high sensitivity to bile acids having a steroid skeleton. In this paper, dioxin sensing that uses fluorescent cyclodextrin is described. Florescent sensing of a dansyl group or anthranyl ground modified cyclodextrin having somewhat different molecular sizes; and sensing of hetero-2 substituted-dansyl-tosyl, modified {beta}-, cyclodextrin are examined. (NEDO)

  17. Improved genetic algorithms using inverse-elitism; Gyakuerito senryaku wo mochiita kairyo identeki algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Kawanishi, H.; Hagiwara, M. [Keio University, Tokyo (Japan)

    1998-05-01

    Improved Genetic Algorithms (GAs) have been proposed in this paper. We have directed our attention to `selection` and `crossover` in GAs. Novel strategies in selection and crossover are used in the proposed method. Various selecting strategies have been used in the conventional GAs such as Elitism, Tournament, Ranking, Roulette wheel, and Expected value model. These are not always effective, since these refer to only the fitness of each chromosome. We have developed the following techniques to improve the conventional GAs: `inverse-elitism` as a selecting strategy and variable crossover range as a crossover strategy. In the `inverse-elitism`, an inverse-elite whose gene values are reversed from those in the corresponding elite is produced. This strategy greatly contributes to diversification of chromosomes. As for the variable crossover range, we combine the following crossover techniques effectively: one is that range in crossover is varied from wide to narrow gradually to carry out global search in the beginning and local search in the ending; another is that range in crossover is varied from narrow to wide. We confirmed validity and superior performance of the proposed method by computer simulations. 18 refs., 9 figs., 3 tabs.

  18. Trial to active seismic while drilling; Jinko shingen wo mochiita SWD eno kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Tsuru, T; Kozawa, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1996-10-01

    This paper describes the development of a more stable SWD system with larger energy by adding an artificial seismic source near the bit. SWD is a technique by which the seismic wave generated while drilling of rocks by bit can be observed on the ground surface and the records equivalent to the reverse VSP can be obtained. For this system, a shell with a vibrator was fixed immediately on the bit as a sub-generator, and total energy of usual impact by the bit and vibration by the vibrator was used as a seismic source for SWD. For the seismic wave generation mechanism of this vibrator, the shell was resonated by the magnetostrictive element, and vibration was given to the bit and drilling pipe. When this seismic source is used, only single frequency is obtained for each vibration due to the utilization of resonance of shell. Therefore, the generation patterns should be made, by which wide band energy can be obtained after the interaction. Since the survey was conducted using this bottom hole seismic source at the drilling depth more than 3,000 m, it was necessary to enhance the vibration energy. 2 refs., 2 figs.

  19. Estimation of fracture aperture using simulation technique; Simulation wo mochiita fracture kaiko haba no suitei

    Energy Technology Data Exchange (ETDEWEB)

    Kikuchi, T [Geological Survey of Japan, Tsukuba (Japan); Abe, M [Tohoku University, Sendai (Japan). Faculty of Engineering

    1996-10-01

    Characteristics of amplitude variation around fractures have been investigated using simulation technique in the case changing the fracture aperture. Four models were used. The model-1 was a fracture model having a horizontal fracture at Z=0. For the model-2, the fracture was replaced by a group of small fractures. The model-3 had an extended borehole diameter at Z=0 in a shape of wedge. The model-4 had a low velocity layer at Z=0. The maximum amplitude was compared each other for each depth and for each model. For the model-1, the amplitude became larger at the depth of the fracture, and became smaller above the fracture. For the model-2, when the cross width D increased to 4 cm, the amplitude approached to that of the model-1. For the model-3 having extended borehole diameter, when the extension of borehole diameter ranged between 1 cm and 2 cm, the change of amplitude was hardly observed above and below the fracture. However, when the extension of borehole diameter was 4 cm, the amplitude became smaller above the extension part of borehole. 3 refs., 4 figs., 1 tab.

  20. Measurement of sediments thickness by ground penetrating radar; Denjihaho wo mochiita kotei taisekibutsu soatsu no sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Nozawa, E [Tokyo Electric Power Co. Inc., Tokyo (Japan); Inagaki, M

    1997-05-27

    An attempt was made to measure thickness of a layer of reservoir bottom sediments by utilizing the electromagnetic reflection method. Because water is a substance difficult for electromagnetic waves to permeate, considerations were given on to suppress attenuation to a minimum, and improve receiving sensitivity. The test used monocycle pulses with a central frequency of 200 MHz. In order to generate stabilized pulses with little unnecessary reflection, an antenna as large as it can be fitted into a rubber boat was employed. In order to acquire referential data, the test was carried out by using simultaneously a sound wave exploration device. The lake at which the test was carried out is a regulating reservoir with a size of about 250 m {times} 150 m, with its bottom made of concrete slab. This means that the lake consists of a three-layer structure comprising water, soil deposits, and concrete bottom from the water surface. According to an example of acquired electromagnetic exploration records, boundary reflection of water and sediments was observed clearly at water depths of 2 to 3 m as a shallow portion and 5 to 6 m as a deep portion. Reflection between the sediments and the bottom plate was also observed sufficiently distinctly. 3 refs., 8 figs.

  1. High resolution resistivity profiling using STRATAGEM system; Stratagem wo mochiita kobunkainohi teiko kozo tansarei

    Energy Technology Data Exchange (ETDEWEB)

    Yamane, K; Inoue, J; Takasugi, S [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Inazaki, T [Public Works Research Institute, Tsukuba (Japan)

    1997-05-27

    A tensor type CSMT method (STRATAGEM) was introduced for the purpose of investigating shallow subsurface, and a field test has been carried out thereon. This system consists of a transmission section, and a sensor section and a data acquisition and processing section to observe waveforms in a responsive electromagnetic field. The signal source is a semi-circular air loop with a radius of a little smaller than 2 m. The measuring points were selected at locations about 200 m apart from the signal source to measure two electric field components and two magnetic field components by using sensors installed on the ground surface. The field test was performed at the Yutsubo area in Oita Prefecture, Japan. The electric field dipole is basically 5 m long, while S and E lines are 10 m long. The measurement frequency ranges from 96 kHz to 1000 kHz. The measurement time was about five minutes, and the whole measurement work including apparatus set-up and withdrawal was completed in about 15 minutes to minimize interference with the field which is a meadow. The field test result revealed that resistivity profile in shallow subsurface can be obtained much more easily than with the conventional CSMT method. 2 refs., 10 figs.

  2. Reservoir characterization using artificial neural network; Neural network wo mochiita choryuso tokusei kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Shimada, N; Kozawa, T [Japan National Oil Corp., Tokyo (Japan); Nishikawa, N; Tani, A [Fuji Research Institute Corp., Tokyo (Japan)

    1997-05-27

    Neural network is used for the prediction of porosity and permeability using logging data as reservoir characteristics, and the validity of this method is verified. For the prediction of reservoir characteristics by the use of seismic survey data, composite seismic survey records obtained by density logging and acoustic logging are used to experiment the prediction of porosity and permeability continuous along lines of wells. A 3-output back propagation network is used for analysis. There is a possibility that this technique when optimized will improve on prediction accuracy. Furthermore, in the case of characteristics mapping, 3-dimensional seismic data is applied to a carbonate rock reservoir for predicting spatial porosity and permeability. This technique facilitates the comprehensive analysis of core data, well data, and seismic survey data, enabling the derivation of a high-precision spatial distribution of reservoir characteristics. Efforts will continue for further improvement on prediction accuracy. 6 refs., 7 figs., 3 tabs.

  3. Car audio using DSP for active sound control. DSP ni yoru active seigyo wo mochiita audio

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, K.; Asano, S.; Furukawa, N. (Mitsubishi Motor Corp., Tokyo (Japan))

    1993-06-01

    In the automobile cabin, there are some unique problems which spoil the quality of sound reproduction from audio equipment, such as the narrow space and/or the background noise. The audio signal processing by using DSP (digital signal processor) makes enable a solution to these problems. A car audio with a high amenity has been successfully made by the active sound control using DSP. The DSP consists of an adder, coefficient multiplier, delay unit, and connections. For the actual processing by DSP, are used functions, such as sound field correction, response and processing of noises during driving, surround reproduction, graphic equalizer processing, etc. High effectiveness of the method was confirmed through the actual driving evaluation test. The present paper describes the actual method of sound control technology using DSP. Especially, the dynamic processing of the noise during driving is discussed in detail. 1 ref., 12 figs., 1 tab.

  4. Contamination-remedying technology based on biotechnology. ; Bioremediation. Biotechnology wo mochiita osen shufuku gijutsu. ; Bioremediation

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, M [The Japan Research Institute, Ltd., Osaka (Japan)

    1993-08-01

    Bioremediation technology is outlined. The bioremediation technology is a contamination-remedying technology for the injurious chemical matter discharged in the environment to be made innocuous by utilizing the decomposing ability of microorganisms. That technology is characterized by its energywise economical performance, secondary waste which is not producible and remedy which is possible on site against the contamination. As a treatment system, that technology comprises solid phase bioremediation (The contaminated soil is purified in a soil treatment unit.), slurry phase bioremediation (The contaminated soil is made slurry and decomposed by microorganisms.) and in-situ bioremediation (The treatment is made by injecting nutrients and microorganisms underground.). As for how to use the microorganisms, there are two methods: One in which living groups of microorganisms are activated and the other in which microorganisms are artificially cultivated. As contaminants in the US, listed are organic solvent, wood preservative, high-molecular aromatic halide, agricultural chemical, military waste, heavy metal waste and radioactive waste. 11 refs., 5 figs., 1 tab.

  5. Capacitive pressure transducer using flexible films. Junan film wo mochiita seiden yoryoshiki atsukaku transducer

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Y.; Tsuchida, N.; Imai, K. (Toyota Technological Institute, Aichi (Japan)); Fujita, K. (Nitto Denko Corp., Osaka (Japan)): Tsuboi, O. (Fujitsu Corp., Tokyo (Japan))

    1992-12-20

    This paper describes the design, manufacture, and evaluation of a capacitive pressure transducer made of polyimide films. The structure of a pressure transducer cell was first determined, and then, the deflection-stress and capacitance-load characteristics of the surface film were analyzed using finite element methods. For the practical stage of manufacture, a polyimide film was emboss processed and electrodes were deposited on the film to construct a pressure transducer cell to which a Schmidt-trigger detecting circuit was connected. As a consequence of the examination of operational characteristics of the cell, it was found that the actual relation between the deflection and load approximately agreed with the linear analyses, and that the capacitance depended with little hysteresis on the gap regardless of the native visco-elasticity of the film. Furthermore, small stick-slip vibration of a contact rubber surface was detected by the transducer to verify its high sensitivity. 17 refs., 18 figs.

  6. Research on variable swirl intake port for high-speed multivalve DI diesel engine. Effects of port configuration on flow characteristics and swirl generation capacity; 4 ben kogata kosoku DI diesel engine no kahen swirl kyuki port ni kansuru kenkyu. Kyuki port haichi ga ryudo tokusei to swirl seino ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Kawashima, J; Ogawa, H; Tsuru, Y [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    In our previous papers, the variable swirl intake port system which can control a wide swirl ratio range (from 4 to 10) was described. This system consisted of two separate intake ports, one of them has a flow control valve for changing the swirl ratio. In this type of variable swirl system, some variations of port combination, port shape, and position can be designed. In this paper, the intake flow characteristics of various port combinations were analyzed on the basis of a steady-state air flow test and 3-dimensional computations. The results indicate that the total performance of the twin ports can be estimated from that of a single port in any kind of port combination. Some difference in flow patterns were found in a variety of port combinations even if each swirl ratio is similar. The selected port combinations in our previous study are good for a wide swirl control range. 11 refs., 9 figs., 1 tab.

  7. Development II of ion current combustion control system. Application to the lean burn system of the micro vehicle engine; Ion denryu wo mochiita nensho seigyo system no kaihatsu. 2. Keijidosha engine wo mochiita lean burn eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Iida, T; Asano, M; Kajitani, M; Kuma, t; Morinaga, Y [Daihatsu Motor Co. Ltd., Osaka (Japan)

    1997-10-01

    The lean bum engine has not been introduced into the micro vehicle so far because of the low cost requirement and small displacement, in spite of it is one of the effective solutions which increase the fuel economy. By the way, we had already reported in the former paper that we developed the ion current combustion control system the architecture of which is cheaper than the other system. In this paper, we described the way how the above system is applied to the lean burn system of the micro vehicle engine and also we reported the gain of fuel economy and the exhaust emission level. 5 refs., 11 figs., 2 tabs.

  8. Experiment of exploration using the active-faults exploration system; Katsudanso tansa system wo mochiita chika tansa jikken

    Energy Technology Data Exchange (ETDEWEB)

    Mikada, H; Sato, H; Iwasaki, T; Hirata, N [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute; Ikeda, Y [The University of Tokyo, Tokyo (Japan). Faculty of Science; Ikawa, T; Kawabe, Y; Aoki, Y [JAPEX Geoscience Institute, Tokyo (Japan)

    1996-10-01

    A system for exploration of active-faults by seismic reflection profiling method was introduced at Earthquake Research Institute, University of Tokyo. A test-run was conducted to check the performance of this system at Ranzan, Saitama Prefecture. This paper describes the confirmed performance of mini-VIB as a wide band frequency seismic source, the quality of data obtained using a digital data acquisition system, and problems for data processing of fault exploration in the future. For the test-run at Ranzan, two-dimensional exploration was conducted by the quasi-three-dimensional data acquisition method using three geophones of 8 Hz, 28 Hz, and 40 Hz, simply arranged in parallel on the measurement line. Using an active seismic vibrator, mini-VIB, data acquisition of faults in the wide band frequency was achieved, which would result in the highly accurate imaging. Operation of data acquisition and processing systems is easy, and the system can be also used as a kind of black box. The existing methods are to be used sufficiently as a tool for imaging of faults. Further research for accumulating experience may become necessary toward the extension of the system expected in the future. 5 refs., 6 figs.

  9. Reexamining results of Iwatoyama tumulus by means of directive antenna; Shikosei antenna wo mochiita Iwatoyama kofun no saijikken

    Energy Technology Data Exchange (ETDEWEB)

    Okamoto, K [Osaka Institute of Technology, Osaka (Japan); Kobayashi, Y [Kyoto University, Kyoto (Japan); Yoda, M [Shiga Prefecture Board of Education, Shiga (Japan)

    1996-05-01

    Investigation was conducted into the Iwatoyama tumulus located at Oaza Yoshida, Yame City, Fukuoka Prefecture, in January 1995, when a directional antenna was used. For the verification of the reliability of the result, another investigation was conducted in the same way. As in the previous effort, a traverse line of 18.8m was provided, and a sub-traverse line of the same length was provided 1m south of the traverse line. Reflection amplitude obtained during this investigation was smaller than that in the previous investigation, which was attributed to it that the contrast in dielectric constants between the rock constituting the main body in the cave and the cavity inside is high in winter and low in summer. In the second investigation, probably because the sub-traverse line was nearer to the southern end of the stone chamber, it became possible to evaluate the area of the stone chamber in the east-west direction, which confirms the conclusion of the first investigation that `it has to be inferred that the tumulus has its stone chamber ceiling at the depth of approximately 3.7m at a spot approximately 9.5-15.0m distant from the survey base for the round foot of the Iwatoyama tumulus and that therefore there exists a cave-type stone chamber with its ceiling 2.5-3.0m high.` 3 refs., 6 figs.

  10. Interferometric SAR and land deformation. Analysis using the dislocation model; Interferometric SAR to chikaku hendo. Dislocation model wo mochiita kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Matsushima, J; Otaki, T; Tanaka, A; Miyazaki, Y [Geological Survey of Japan, Tsukuba (Japan)

    1996-05-01

    The diastrophism by the earthquake-induced dislocation is investigated by interferometry (INSAR) which represents the diastrophism by the interference fringes of equiphase difference lines. A joint research group at Geographical Survey Institute and National Space Development Agency showed the diastrophism in the vicinity of the ground surfaces before and after the Hyogoken Nanbu Earthquake by the INSAR interference images in 1995. This paper discusses the effects of observation in the vision line direction from the satellite and dislocation parameters on the interference images. The dislocation model uses a slanted rectangular model in a semi-infinite medium, to calculate static displacements and strain distributions at the ground surface, when dislocation changes. It is found that the INSAR interference images, detecting displacements in the vision line direction from the satellite, significantly change as the vision line direction changes, and that the actual displacement cannot be given by the images alone. This paper also shows sensitivity of the interference images to the dislocation parameters. 3 refs., 9 figs., 1 tab.

  11. Suppression of numerical dispersion using FD modified operators; Atarashii sabunho no enzanshi wo mochiita suchi bunsan no yokusei

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, N; Geller, R [The University of Tokyo, Tokyo (Japan). Faculty of Science

    1996-05-01

    The author, et al., have developed a formal evaluation theory for errors in numerical solutions and derived on the basis of this theory the conditions that a modified error minimizing operator should satisfy. A modified operator was derived for a calculus of finite difference in the time domain making use of this error evaluation theory. In this study, a modified operator was derived for O (2, 2) in the calculus of finite difference in time, and the operator was used in the calculation for the old and new methods about 1-dimension inhomogeneous media, and the two were quantitatively compared in CPU time and calculation accuracy. The calculation used 500 space grids and 5000 time grids. With the ratio of the time grid gap and space grid gap are kept constant, both CPU time and calculation accuracy were in proportion to the square of the number of grids. It was found in view of the result that the new method, as compared with the old method, needs only approximately 1/20 of CPU time in performing calculations of the same precision and that it maintains calculation accuracy that is approximately 20 times higher in the said CPU time. 4 refs., 2 figs., 1 tab.

  12. Remote reference processing in MT survey using GPS clock; MT ho ni okeru GPS wo mochiita jikoku doki system

    Energy Technology Data Exchange (ETDEWEB)

    Yamane, K; Inoue, J; Takasugi, S [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Kosuge, S [DRICO Co. Ltd., Tokyo (Japan)

    1996-05-01

    A report is given about the application of a synchronizing system using clock signals from GPS satellites to a remote reference method which is a technique to reject noise from the MT method. This system uses the C/A code out of the L1 band waves from NAVSTAR/GPS satellites. The new system was operated in MT method-using investigations conducted at China Peninsula, Aichi Prefecture, and Izu Peninsula, Shizuoka Prefecture, with the reference points placed several 100km away in Iwate Prefecture on both occasions. It was found as the result that it is basically possible to catch signals from the GPS at any place, that the signals are accurate enough to be applied to time synchronization for the MT method, and that the signals assure a far remote reference method with a separation of several 100km between the sites involved. The referencing process at high frequencies whose feasibility had been doubted proved a success when highly correlated signals were exchanged between two stations over a distance of several 100km. 5 refs., 9 figs.

  13. Improvement of two-dimensional gravity analysis by using logarithmic functions; Taisu kansu wo mochiita nijigen juryoku kaiseki no kairyo

    Energy Technology Data Exchange (ETDEWEB)

    Makino, M; Murata, Y [Geological Survey of Japan, Tsukuba (Japan)

    1996-05-01

    An examination was made, in the two dimensional tectonic analysis by gravity exploration, on a method that was applicable from a deep underground part to a shallow geological structure by using logarithmic functions. In the examination, a case was considered in which an underground structure was divided into a basement and a covering formation and in which the boundary part had undulations. An equation to calculate a basement structure from a gravity anomaly was derived so that, taking into consideration the effect from the height of an observation point, it might be applicable to the shallow distribution of the basement depth. In the test calculation, a model was assumed reaching the depth near the surface with the basement being a step structure. Density difference was set as 0.4g/cm{sup 3}. An analysis using an equation two-dimensionally modified from Ogihara`s (1987) method produced a fairly reasonable result, showing, however, a deformed basement around the boundary of the step structure, with the appearance of a small pulse-shaped structure. The analysis using logarithmic functions revealed that the original basement structure was faithfully restored. 3 refs., 5 figs.

  14. Studies on artificial light type vegetation plant using fluorescent lamps. Keikoto wo mochiita jinko kogata shokubutsu kojo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Iwao, K [Chubu Electric Power Co. Inc., Nagoya (Japan)

    1991-11-01

    This paper describes the contents of studies carried out for four years on a fluorescent lamp type vegetation plant. The equipment consists of a chiller unit with 5 HP, a motive power board of three-phase 200 V/feeder with an annual power capacity of 20 kW at maximum, and a micro-computer to control the culture environmental conditions. Discussions were given on the equipment performance, profitability, production capacity for salads and lettuces, and related data. Although the system has some disadvantage in the economy, it provided effective results on the know-hows in culturing high-class vegetables and fruits under season-free and chemical-free conditions. Since the natural light is also required, the professional knowledges and know-hows in this area were incorporated in the development. Fluorescent lamps emitting three primary colors of red, green and blue were devised and used. Because insufficient light intensity would raise the temperature only up to 42{degree}C when the ambient temperature is 25{degree}C, a proximity illumination system was adopted, which provided 45KIx high light intensity as well as the working spectra over an wide area. Tomato cultivation has also become possible, which is an epoch-making success. The system yielded better than hydroponic cultivation in solar greenhouse of the same size. 11 refs., 16 figs., 2 tabs.

  15. Evaluation of paramagnetic species in coals with iodine doping technique; Yoso tenkaho wo mochiita sekitanchu no jojiseishu no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Aizawa, S.; Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    Electron paramagnetic resonance (EPR) of coals was considered by using iodine doping technique. Sub-bituminous coal (WA) and bituminous coal (UF) were used to observe EPR spectra using microwaves. With the UF coal, strength of the narrow component of the spectra was found constant regardless of amount of the doped iodine, wherein radicals without interaction with iodine were detected. Strength of the broad component increased with the iodine doping amount, where in deviation of {pi} electrons was detected, which have been generated as a result of interaction between aromatic rings and iodine in the coals. Spin concentration of the WA coal with low coalification degree is constant regardless of the iodine doping amount, and the interaction of the iodine with the aromatic rings was found small. The higher the coalification degree, the more the aromatic ring structure grows, and electron donor capability for the iodine increases. In a system with the entire spin being uniform, the spectrum height shows a saturation phenomenon against increase in microwave output. A non-uniform system, in which the oriented spin forms small groups and is in local thermal equilibrium, does not show saturation, but increases monotonously. 2 refs., 5 figs.

  16. Carbon dioxide gas sensor based on lithium ionic conductor. Lithium ion dendotai wo mochiita tansan gas sensor

    Energy Technology Data Exchange (ETDEWEB)

    Imanaka, N [Osaka University, Osaka (Japan). Faculty of Engineering

    1992-10-31

    A small-sized inexpensive carbon dioxide gassensor was prepared using LiTi2 (PO4)3 +0.2Li3PO4 as lithium-ion conductive, solid electrolyte and its detectability and the effects of co-existing gases were examined. The above compound was obtained by the method where a powdery mixture of Li2CO3, TiO2, (NH4)H2PO4 and Li3PO3 was molded in the presence of a sintering assistant, subjected to hydrostatic press, and sintered. Measurements were made on the relation between CO2 concentration and the electromotive force of the CO2 sensor made of the compound and the influence of concentration of coexisting NO2, SO2 or CH4 on the electromotive force. The results are summarized as follows. A linear relation exists between the electromotive force and the CO2 concentration in the range from 80ppm to 1% to show a good agreement between theoretical and experimental results. Coexistence of NO2 the range of 100-4500ppm has no influence on the electromotive force. Coexistence of methane gives a linear relation. SO2 of even 20ppm lowers the electromotive force. As for the relation with hurmidity, when CO2 concentration is less than 1000ppm, electromotive force decreases as the amount of water vapor is increased. CO2 concentration in the range from 100ppm to 1% at 350[degree]C can be detected by selecting good electrodes. 13 refs., 11 figs.

  17. Non-destructive inspection technology using a magnetic transmission sensor; Jiki toka sensor wo mochiita hihakai kensa gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Obama, H.

    1996-06-01

    A newly developed magnetic sensor for non-destructive inspection has acquired the U.S. patent. The starting point of the invention was an inspection of aluminum broth bags in cup-noodle containers with aluminum leaf cover, which was asked from a food maker. A method was developed, in which the microwave is transmitted through containers below their covers and the reflected wave is detected. Then, development of an inspection apparatus for spot welding parts used for automobiles was requested. Since welding is carried out using large current for the spot welding, magnetic characteristics change greatly, which is a remarkable phenomenon appearing especially for magnetic substances. This was found out to be the same phenomenon as the hardening of swords consisting of high temperature heating, pressurizing, and quenching. This substance with two changes can be considered as another material different from the base metal. Coils fitted to impressions were made, and their test pieces were measured. The correlation coefficient over 0.9 was obtained between measured values and results of tensile strength tests. This apparatus can be applied to the non-destructive inspection of internal defects of castings. 2 figs.

  18. Hydrogen storage alloy and alkaline battery employing it; Suiso kyuzo gokin denkyoku to sorewo mochiita arukari niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Ono, T. [Furukawa Electric Co. Ltd., Tokyo (Japan); Furukawa, J. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

    1997-01-28

    The invented hydrogen storage alloy electrode is produced in the following way: The hydrogen storage alloy powder is mixed with conductive material and rubber-like elastomer. A certain amount of viscosity modifier aqueous solution such as aqueous solution of carboxymethylcellulose is added to the said mixture to prepare a mixed paste. The said paste is dried and rolled after being filled in the current collector to be held by the current collector. The rubber-like elastomer has a strong bonding force, though it is soft. Both hydrophobic and hydrophilic groups are contained in its molecule. Example of such material is a partly fluorinated or chlorinated acrylonitrile-butadiene rubber. The addition of fluorine or chlorine atom is done to its double bond. The addition of the rubber-like elastomer is controlled to 0.05 - 10 wt% of hydrogen storage alloy powder to suppress the elevation of inner-battery pressure at the time of overcharge. 2 tabs.

  19. Field test on sand compaction pile method with copper slag sand; Dosuisai slag wo mochiita SCP koho no shiken seko

    Energy Technology Data Exchange (ETDEWEB)

    Minami, K.; Matsui, H.; Naruse, E.; Kitazume, M. [Port and Harbour Research Inst., Kanagawa (Japan)

    1997-09-20

    This paper describes the sand compaction pile (SCP) method using copper slag sand. The SCP method is a method by which sand compaction piles are constructed in the ground, and improvement can be obtained in a short period. This method has been widely used even in the port areas for enhancing the bearing power of soft clay ground and the lateral resistance of sheet pile. A great deal of sand is required as a material. The sand requires high permeability, proper size distribution with less fine particle fraction content, easy compaction property with enough strength, and easy discharging property from the casing of construction machines as required properties. Recently, it becomes hard to secure proper sand materials. The copper slag sand is obtained from refining process of copper as a by-product which is quenched in water flow and crushed in water. The copper slag sand has higher particle density than that of sand, excellent permeability, and similar size distribution to that of sand. From compaction drainage triaxial compression test and permeability test, it was found that the mechanical properties of copper slag sand did not change by the crushing of grains with keeping excellent permeability. Through the test construction, applicability of the copper slag sand to the SCP method could be confirmed as an alternate material of sand. 17 refs., 9 figs., 4 tabs.

  20. Application of the seismic survey ahead of tunnel face; Danseiha wo mochiita kiriha zenpo tansa no tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Nagai, S; Nakajima, N [JDC Corporation, Tokyo (Japan)

    1997-10-22

    Measurements have been made in a water channel tunnel having a small diameter and shallow earth covering, by using a tunnel seismic prediction (TSP) system to predict the nature of soil up to about 150 meters ahead of a face, which uses reflection method elastic waves. The water channel tunnel has a diameter of 2.8 m, and extends over a total distance of 706 m. The nature of soil at the face is composed of rocks, in which dark gray and hard striped phthanites are distributed and joint interval is about 20 cm. The measurements were performed on 24 vibration holes with hole interval of about 1.5 m using an explosive of 50 grams per hole. Diffraction stack processing method was used to execute the analysis. As a result of the discussions, a point changing from hard to soft soil was predicted at a point 18 m ahead of the face, and a point changing from soft to hard soil at a point 70 m ahead of the face. The changing point for the soil nature as observed by drilling showed a discrepancy of 10 m at the point changing from hard to soft soil as compared with the prediction derived by using the TSP exploration. No discrepancy was recognized in the point changing from soft to hard soil. The discrepancy is thought to have been caused from the geological change in the explored area being moderate and the lithofacies being free from change. 8 figs., 2 tabs.

  1. Evaluation of column flotation results with a film flotation method; Film fusenho wo mochiita column fusen kekkan no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H.; Matsukata, M.; Ueyama, K. [Osaka University, Osaka (Japan). Faculty of Engineering Science

    1996-10-28

    Change in wettability of coal particle surfaces due to kerosene adsorption was studied by using a film flotation method. The applicability of a film flotation method to coals modified by kerosene adsorption was first confirmed. In experiment, film flotation was applied to Illinois coal modified by aqueous methanol solution and kerosene adsorption, and the weight percent of residual particles on a gas-liquid interface and kerosene in aqueous methanol solution were analyzed to verify the applicability of a film flotation method. Film flotation was applied to Datong and Illinois coals modified by kerosene adsorption, and the weight percent of residual particles on a gas-liquid interface was plotted to surface tension of liquid. As a result, the weight percent of hydrophobic particles within 50mN/m in surface tension slightly increased in Datong coal and remarkably increased in Illinois coal with kerosene addition. It was thus suggested that in addition to surface tension, the distributions of hydrophilic and hydrophobic strengths on the surface of each coal particle should be considered to understand attachment of coal particles and bubbles. 6 refs., 4 figs.

  2. Prediction of powerplant vibration using FRF data of FE model; Dentatsu kansu wo mochiita power plant shindo yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, T; Tsukahara, M; Sakaguchi, M; Takahashi, Y [Honda R and D Co. Ltd., Tokyo (Japan)

    1997-10-01

    For the purpose of shortening the development period, the estimation of powerplant vibration has become more important in the early design stage, and eigenvalue analysis by FEM is commonly used to solve this problem. Eigenvalue Analysis cannot directly predict vibration levels under running conditions that affect the durability of each component and the vibration of a car body. This paper presents a new approach using FRF data from FE models for accurate prediction of engine vibration under running conditions. By applying this approach to an in-line four cylinder engine, the predicted vibration is reasonably comparable with experimental results. 3 refs., 8 figs.

  3. Investigation of design method for air-conditioning system using CAE; CAE wo mochiita kucho haifu yosoku no ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Matsumoto, M; Miyake, N; Takeuchi, T; Kori, I [Mitsubishi Motors Corp., Tokyo (Japan)

    1997-10-01

    Designing the air-conditioning system, the distributions of the flow rate and the temperature at each air outlet are important factors. This paper describes the prediction method using CFD (Computational Fluid Dynamics), which is based on the `{kappa}-{epsilon} turbulence model` and unstructured grid system. It is proved that conventional tetrahedral grid system gives adequate results for the flow rate prediction. However, it is also found that improvement is required for the thermal prediction. At the result, we suggested that the `prism mesh`, which has been developed for detailed calculation of the boundary layer properties, is essential for such the heat transfer problem. 4 refs., 13 figs.

  4. Photometric analysis on concentration characteristics of Fresnel lenses; Fotometoriho wo mochiita Fresnel lens no shuko tokusei kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, A [Tokyo University of Agriculture and Technology, Tokyo (Japan)

    1997-11-25

    Light concentration characteristics of Fresnel lenses were analyzed by using photometry. Light concentrating systems include a reflective system represented by a rotary parabolic mirror, and a refractive system represented by the Fresnel lens. The refractive system has a focused section broadened as much as the dispersion effect in association with refraction, and cannot derive a focus with high magnification as compared with the reflective system which can achieve it. The refractive system causes reduction in collected light intensity to about half on a parax, hence a large amount of loss. However, the system can be made available inexpensively due to mass production by using mold formation. Although it is difficult to utilize all of the light, 95% of the received radiation is concentrated in an opening area with a radius of about 4G (G is a radius of an image of solar light at a focus plane which passes through the center of a Fresnel lens). The average magnification of light concentration at this time in the opening area reaches 390 times. When a 3-D compound parabolic concentrator (CPC) with a radius of 4G is placed on a lens focus as a secondary light concentrator, the final magnification of light concentration shows a value of about 2700 times, whereas restoration of 39% is possible, as compared with a rotary parabolic mirror. The system has sufficient possibility to be used for high-temperature light concentration. 3 refs., 5 figs., 1 tab.

  5. Forced-circulation solar water heater using a solar battery; Taiyo denchi wo mochiita kyosei junkahshiki taiyonetsu onsuiki

    Energy Technology Data Exchange (ETDEWEB)

    Asai, S; Mizuno, T [Yazaki Corp., Tokyo (Japan)

    1997-11-25

    Optimal operation control was discussed on a forced-circulation solar water heater using solar cells not only as the power supply of a heat collecting pump, but also for controlling operation of the heat collecting pump. With this system, when the amount of power generated by solar cells reaches a sufficient level for operating the heat collecting pump, the heat collecting pump starts operation, wherein the heat collecting medium circulates in the system. The discussion was given by using simulation based on experimental expressions such as the relation expression between insolation and heat collecting medium flow rate as derived from the result of the system`s heat collecting performance test. As a result, the following conclusions were obtained: optimal insolation for activating the discussed system is from 50 to 100 W/m {sup 2}, and the heat collected within this range is within -1.5% of the collected heat amount at an optimum value; optimal activating insolation for the case of 1000 to 2000 W/m {sup 2} with low daily cumulative insolation is from 0 to 50 W/m {sup 2}, whereas the optimal activating insolation amount increases as the daily cumulative insolation amount increases; and the optimal activating insolation amount increases as water to be supplied requires higher temperature. 1 ref., 17 figs., 2 tabs.

  6. FY1995 ultrafast photonic devices using dielectric domain superlattice; 1995 nendo yudentai domain chokoshi wo mochiita chokosoku photonic device

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-31

    All optical wavelength conversion around 1550nm is of great importance for the wavelength division multiplexing optical communication system. A dielectric domain superlattice, which has a periodically domain inverted structure, has a wide potential for the various nonlinear interactions such as second harmonic generation (SHG) and difference frequency generation (DFG). The purpose of our research is to establish the theoretical bases and fabrication processes of the guided-wave wavelength converter based on the DFG by domain-inverted LiTaO{sub 3}. We have investigated basic characteristics of guided-wave DFG devices and developed the domain-inversion process by an electric field poling utilizing a liquid electrolyte consisting of LiCI in deionized water as a electrode for applying the electric field to LiTaO{sub 3} substrate. By controlling the injection current for the domain inversion precisely, we fabricated successfully uniform domain-inverted structures. 0.5mm-thick domain-inverted LiTaO{sub 3} of 7.8, 17.2 and 21.3 {mu}m periods and 0.5 duty ratio were obtained by optimizing electrode structure and the domain-inversion process. Waveguide structures can increase the conversion efficiency of DFG by several orders of magnitude over bulk interactions. We have also developed waveguide fabrication process for the domain-inverted LiTaO{sub 3} substrate. Low loss proton-exchanged waveguides were formed by annealed proton exchange technique without a degradation of the domain inversion structure. Domain-controlled nonlinear optics by designing the ferroelectric domain structure of LiTaO{sub 3} and LiNbO{sub 3} make it possible to extend all the spectral range from ultra-violet to far-infrared and THz wave region. (NEDO)

  7. Temperature measurement of geothermal wells by optical fiber sensor; Hikari fiber sensor wo mochiita chinetsusei no ondo bunpu keisoku

    Energy Technology Data Exchange (ETDEWEB)

    Matsushima, N; Sakaguchi, K [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    Experiments of temperature measurement were conducted in high temperature and high pressure geothermal wells using optical fiber sensor. A temperature measurement system using optical fiber sensor was applied to geothermal wells. Working availability was confirmed under the condition up to the depth of 1,750 m and the temperature of 240 centigrade. Observed values agreed well with those observed by the conventional temperature logging. Durability of the optical fiber sensor was also sufficient. The maximum standard deviations of measured values were 1.3 centigrade at the depth of 1,750 m at 195 centigrade for the loop-type sensor, and 3.7 centigrade at the depth of 365 m at about 200 centigrade for the single-end sensor. Although the accuracy was inferior to the conventional measurement using a thermo couple, it was enough to be applied to usual temperature logging. Furthermore, for this system, the temperature profile in the whole well can be monitored, simultaneously. Through the experiments, the detailed successive change of temperature profile accompanied with the water injection can be clearly illustrated. 3 refs., 7 figs.

  8. Formal verfication of a railway crossing controller using time petri nets; Taimupetorinetto wo mochiita fumikiri seigyo puroguramu no keishikiteki kensho

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, R. [The Nippon Signal Co. Ltd., Tokyo (Japan); Yoneda, T. [Tokyo Inst. of Technology, Tokyo (Japan)

    1994-12-20

    In the system requesting the real-time property, detecting the dugs in the method by carrying out the verification at the stage of method is important for excluding the error from the latter process. The verifying device for investigating whether the properties are satisfied by the system with the expression of the operation rules of system with time Petri nets and presenting the properties to be verified with real-time linear time-phase theory is developed by Yoneda, et al. In this paper, the verification of train check and warning-controlling operation in railway-crossing is carried out by using said verifying device, and the effectiveness of this verifying method is examined. In the practical controlling program, the mistakes in design occurs easily because of the further execution of complex processings including the countermeasure to the defect of short circuit in controlling unit and the control of up/down trains. It is planned in the future to modeled such processings as well as functions and to verify the system more utilizable. 12 refs., 11 figs., 1 tab.

  9. Active SWD using monochromatic source wavelet; Tan`itsu shuhasu no shingen hakei wo mochiita active SWD

    Energy Technology Data Exchange (ETDEWEB)

    Tsuru, T; Kozawa, T [Japan National Oil Corp., Tokyo (Japan); Taniguchi, R [Mitsubishi Electric Corp., Tokyo (Japan); Nishikawa, N [Fuji Research Institute Corp., Tokyo (Japan); Matsuhashi, K

    1997-05-27

    As part of developing efforts for physical exploration technologies for oil reservoirs, this paper describes development of an active seismic while drilling (SWD). The SWD is a seismic exploration method to acquire records equivalent to VSP using seismic waves generated from a bit executing excavation, and is capable of detection and control on a real time basis during the excavation. However, the drawback is that it is subjected to a limitation in the bit. To eliminate this limitation, an artificial seismic source method was devised. In other words, this is an SWD utilizing an artificial seismic source. The contrivance is such that a shot sub containing a magnetic distortion oscillator is attached directly above a bit to generate vibration artificially, and try to utilize larger seismic energy by combining this vibration with that generated from the excavating bit. Frequency band in the seismic source is as narrow as nearly a single frequency waveform. Preparing a time-depth curve from the data and identifying position of a bit making excavation requires reading the initial travel time. A waveform recognition technology was applied, which utilizes a matching evaluation function used in pattern recognition. This made waveform recognition possible at high accuracy. 2 figs., 1 tab.

  10. Application of VSP to geological investigation; P ha oyobi S ha VSP wo mochiita shinso chishitsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    Kinugasa, Y [Geological Survey of Japan, Tsukuba (Japan); Feng, S; Sugiyama, T; Ishikawa, K [Chuoh Kaihatsu Corp., Tokyo (Japan)

    1997-05-27

    Discussed in this paper are the P-wave and S-wave zero-offset VSPs carried out utilizing boreholes located in Nada Ward, Kobe City, and Hokudan-cho, Hyogo Prefecture, as part of the deep layer boring survey following Hanshin Earthquake Disaster. This effort aims at the elucidation of P-wave and S-wave velocity structures, high-precision identification of data obtained by the surface reflection method, and collection of basic data for active faults investigation in the future. Among the velocity structures obtained for various layers, the S-wave velocity structures in particular agree with the stratigraphy excellently and may be utilized in seismic analyses to be conducted in the future. Reflection from geological boundaries is received with precision, providing accurate information about correlation between reflection and geological cross sections. The records will be useful in formulating plans for reflection surveys for instance of the boundary between the Osaka group and Kobe group. Generally speaking, reflection coefficients are large when the reflection is from a boundary where difference is great in elastic wave impedance (mainly difference in velocity). In the case of the boundary between the Kobe group and granite in Awaji Island, however, no strong reflection is found despite the great difference in velocity. This is attributed to the complicated, sharp inclination of the basement rock and to its weathering. 4 refs., 8 figs.

  11. Flow velocity anemometer using ultrasonic waves in underground airways. Choonpa wo mochiita chika fudo fusokukei no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, K.; Imai, T.; Miyakoshi, H. (Akita Univ., Akita (Japan). Mining College); Onozuka, T.; Yasunaga, K. (Hanaoka Mining Co. Ltd., Akita (Japan))

    1993-10-25

    In a facility utilizing the subterranean space at the great depth of about 50m or less from the surface in particular, the airflow velocity monitor utilizing ultrasonic waves is considered as an airflow anemometer suitable for the environment of an underground airway network. In this paper, the results of the application test and the long term demonstration test both conducted at Matsumine Mine and Fukazawa Mine of Hanaoka Mining Industry are mentioned which concern the newly developed airflow velocity monitor utilizing ultrasonic waves. The features and performance of this ultrasonic wave monitor are roughly as follows; since a small ultrasonic wave transceiver can be installed on the surface of the airway wall, the transceiver does not become an obstacle for traffic in the airway and the average airflow velocity in the airflow path can be estimated with accuracy better than that of the anemometer for point measurement. The airflow direction at the underground airway can be detected. The responsiveness to airflow velocity fluctuations is relatively good. The abrupt ups and downs of output due to passing transportation machines can be detected. The measuring circuit has been simplified by the analogue treatment of time measurement. The average airflow velocity at the airflow velocity profile can be estimated through multiplication by 0.93 of the airflow velocity value measured with the monitor. 11 refs., 16 figs., 1 tab.

  12. Analysis of a DSM program using an end use model; End use model wo mochiita DSM program no bunseki

    Energy Technology Data Exchange (ETDEWEB)

    Asano, H.; Takahashi, M.; Okada, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-01-30

    An end use model used in the United States who is advanced in demand-side management (DSM) was used to discuss possibilities of designing and evaluating Japan`s future DSM measures. The end use model assumes energy demand based on such factors as device characteristics, meteorological data, energy prices, user characteristics, market characteristics and DSM measures. The model calculates energy demand amount by end uses basically by multiplying assumptions on device unit requirement, device retention rate, and number of users. A representative tool as an end use model that handles load shapes is the hourly electric load model (HELM). It assumes an annual load curve and predicts a maximum system load. The present discussions have performed estimation on demand for consumer use air conditioners in a day in which a maximum summer load occurs in a reference year, estimation on load in a maximum load day in an estimated year, and estimation on weather sensitivity of loads. 5 refs., 5 figs.

  13. Study on grout-filled coupling steel sleeve; Kokan sleeve wo mochiita grout jutenshiki tekkin tsugite ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, Y. [Osaka University, Osaka (Japan)

    1997-06-01

    Newly designed grout-filled coupling sleeve is discussed, which uses as the sleeve an electric resistance welded tube with protrusions formed in a checker pattern on its inner wall and is capable of using various premixed grouting materials available on the market. Specimens are subjected to uniaxial tensile loading and positive/negative cyclic loading, and the impact of various factors on the basic performance of the specimens and their stress/distortion characteristics at local spots in the reinforcing bar are disclosed. In the positive/negative cyclic loading in the plastic region, however, such findings are not obtained. In view of the stress/distortion characteristics at local spots in the reinforcing bar, a method is proposed for estimating the coupling strength and fracture type. A method for estimating the deformation behavior of the coupling, however, is not proposed. Investigations are conducted into the manufacture and installation of the grout holding framework, coupling fixing jigs, plugs, etc., and it is found that precasting should be studied in the future. 38 refs., 156 figs., 30 tabs.

  14. Pseudo-noise generator using UNMBER SIEVE''. Kazu furui wo mochiita giji ransu seiseiki

    Energy Technology Data Exchange (ETDEWEB)

    Kyan, S.; Teruya, H. (University of the Ryukyus, Okinawa (Japan). College of Engineering)

    1992-09-01

    In data communications which require secrecy, the Vernam cipher method is often used because of its simple principle and high security. It is necessary for this method to generate key streams as random numbers. The conventional generating methods using linear feedback shift register (LFSR) or data encryption standard(DES) have some problems in and security and circuit complexity. This paper proposes a pseudo-noise generator of relatively simple structure using number sieve, and describes its structure and security. The pseudo-noise generator consists of the number sieve circuit combined With shift resistors of figures of 8 prime numbers from 2 to 19 and other resisters containing AND in feedback area. The total number of keys that can be selected is 3.8[times]10[sup 25], which is not readable from the aspect of calculation volume. Concerning a model of the number sieve circuit with shift resistors which are reduced to 4, linear complexity, which is part of evaluation standard for the security of pseudo-random numbers for cipher, and hamming distance for different keys are examined. 10 refs., 8 figs., 3 tabs.

  15. Forced-circulation solar water heater using a solar battery; Taiyo denchi wo mochiita kyosei junkanshiki taiyonetsu onsuiki

    Energy Technology Data Exchange (ETDEWEB)

    Asai, S; Mizuno, T [Yazaki Resources Co. Ltd., Shizuoka (Japan)

    1996-10-27

    For the purpose of satisfying demands for qualitative improvement on tapwater temperature and pressure, an indirect-type solar water heater using solar cells, in which a closed type hot water storage tank connected directly to the water supply is integrated with a solar collector, was examined for its characteristics and performance. The heat collecting medium is a water solution of polypropylene glycol, which circulates through the solar collector pump, cistern, solar collector, and heat exchanger (hot water storage tank). The results of the test are summarized below. When comparison is made between the two solar collector pump control methods, the solar cells direct connection method and the differential thermo method utilizing temperature difference between the solar collector and the hot water storage tank, they are alike in collecting heat on clear days, but on cloudy days the latter collects 5% more than the former. In winter, when the heat exchanger heat transfer area is 0.4m{sup 2} large, a further increase in the area improves but a little the heat collecting efficiency. An increase in the medium flow rate and temperature, or in the Reynolds number, enhances the heat collecting efficiency. 13 figs., 6 tabs.

  16. Performance analysis of dish solar stirling power system; Stirling engine wo mochiita taiyonetsu hatsuden system no seino yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Tsuchiya, K; Yamaguchi, I [Meiji University, Tokyo (Japan); Naito, Y; Momose, Y [Aisin Seiki Co. Ltd., Aichi (Japan)

    1996-10-27

    In order to estimate the performance of the dish solar Stirling power system, matching and control of each component system were studied, and the performance of the 25kWe class power system was estimated on the basis of direct solar radiation measured in Miyako island, Okinawa. Application of a Stirling engine to solar heat power generation is highly effective in spite of its small scale. The total system is composed of a converging system, heat receiver, engine/generator system and control system. As the simulation result, the generator output is nearly proportional to direct solar radiation, and the system efficiency approaches to a certain constant value with an increase in direct solar radiation. As accumulated solar radiation is large, the influence of slope error of the converging mirror is comparatively small. The optimum aperture opening ratio of the heat receiver determined on the basis of mean direct solar radiation (accumulated solar radiation/{Delta}t (simulated operation time of the system)), corresponds to the primary approximation of the opening ratio for a maximum total generated output under variable direct solar radiation. 6 refs., 6 figs., 1 tab.

  17. Development of economical and high efficient desulfurization process using low rank coal; Teitankadotan wo mochiita ankana kokoritsu datsuryuho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takarada, Y; Kato, K; Kuroda, M; Nakagawa, N [Gunma University, Gunma (Japan). Faculty of Engineering; Roman, M [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    Experiment reveals the characteristics of low rank coal serving as a desulfurizing material in fluidized coal bed reactor with oxygen-containing functional groups exchanged with Ca ions. This effort aims at identifying inexpensive Ca materials and determining the desulfurizing characteristics of Ca-carrying brown coal. A slurry of cement sludge serving as a Ca source and low rank coal is agitated for the exchange of functional groups and Ca ions, and the desulfurizing characteristics of the Ca-carrying brown coal is determined. The Ca-carrying brown coal and high-sulfur coal char is mixed and incinerated in a fluidized bed reactor, and it is found that a desulfurization rate of 75% is achieved when the Ca/S ratio is 1 in the desulfurization of SO2. This rate is far higher than the rate obtained when limestone or cement sludge without preliminary treatment is used as a desulfurizer. Next, Ca-carrying brown coal and H2S are caused to react upon each other in a fixed bed reactor, and then it is found that desulfurization characteristics are not dependent on the diameter of the Ca-carrying brown coal grain, that the coal is different from limestone in that it stays quite active against H2S for long 40 minutes after the start of the reaction, and that CaO small in crystal diameter is dispersed in quantities into the char upon thermal disintegration of Ca-carrying brown coal to cause the coal to say quite active. 5 figs.

  18. New biological deodrization device using dried activated sludge. Kanso odei wo mochiita shinki seibutsu dasshu sochi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hatakeyama, S.; Nagayasu, K.; Suwa, T.; Hayashitani, M.; Ito, H.; Habata, K.; Kitakaze, T. (Kawasaki Heavy Industries, Ltd., Tokyo (Japan))

    1993-10-20

    The new biological deodorization device was developed using dried activated sludge as deodorant. Activated sludge obtained from a waste water treatment plant was dried at room temperature to protect from extinction of microorganisms in it before its charge into the device, and washed by water only as required. Offensive odor substances were oxidation-decomposed by microorganism after their adsorption into sludge surfaces, while microorganisms survived for a long time while getting such substances as nutritive sources. As basic deodorization characteristics were studied with the experimental device and artificial odor gases, more than 99% of 200 and 2,000 ppm H2S were removed at space velocities of 400/h and 33/h, respectively, together with nine typical offensive odor substances. As the result of demonstration tests with the small test device installed in a public waste water treatment plant, a high deodorizing efficiency was retained for 10 months or more, and its running cost was as low as 75% of that of current systems because of only one necessary washing every month. 3 refs., 14 figs., 12 tabs.

  19. Quantification of taste of green tea with taste sensor; Aji sensor wo mochiita ryokucha no aji no teiryoka

    Energy Technology Data Exchange (ETDEWEB)

    Ikezaki, H.; Taniguchi, A. [Anritsu Corp., Tokyo (Japan); Toko, K. [Kyushu University, Fukuoka (Japan)

    1997-08-20

    We have developed a multichannel taste sensor with artificial lipid membranes and have applied it to quantification of taste of green tea. We used multiple regression analysis and found high correlations of outputs of the taste sensor with the results of sensory test (taste, flavor and color) and chemical analyses (amino acids and tannin that are main taste substances in green tea). It is concluded that the taste sensor has a potential for quantification of taste of green tea. The taste sensor responds not only to amino acids and tannin, but also to many other taste substances, and hence it contains much more taste information than conventional chemical analyses. 12 refs., 5 figs., 6 tabs.

  20. Cleaning of road accessories with powdered sodium bicarbonate; Jutansan natrium ryu wo mochiita doro fuzokubutsu no senjo

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, H.; Amagori, Y.; Mori, E. [Japan Highway Public Corporation, Tokyo (Japan)

    1998-06-25

    A method for cleaning highway accessories with powdered sodium bicarbonate is developed, to replace mechanical cleaning by a multi-purpose vehicle or manual cleaning, and thereby to reduce road maintenance cost. It pneumatically blows sodium bicarbonate particles by a blaster connected to a water tank and compressor onto a variety of stains to remove them. The cleaning system is applicable to a variety of purposes, allowing dry and wet cleaning modes to be easily switched from each other. Sodium bicarbonate, being naturally occurring, is harmless, and its type can be freely chosen. This method was applied in FY1996 mainly to cleaning interior plates in highways, to collect the basic data. Its cleaning effectiveness has been confirmed by applying it to the internal plates, which are difficult to clean by a multi-purpose vehicle, and illuminators in tunnels, whose cleaning areas are narrow. It recovers reflectivity of plates to 85% of the initial level at the highest, and shows 3 times higher efficiency for heavily stained plates. The test was continued in FY1997. It shows an approximately 5 times higher cleaning capacity than the conventional method, greatly reducing cleaning time, especially for illuminators in tunnels. 7 figs., 5 tabs.

  1. Study on fault diagnostic system using modularized knowledge; Mojuru gata chishiki wo mochiita ijo shindan system ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shimada, Y.; Sayama, H.; Suzuki, K. [Okayama Univ. (Japan). Dept. of Industrial and Mechanical Engineering

    1997-08-15

    Recently, a fault diagnostic expert system was prosperously developed as an objective of chemical plants and nuclear power plants. In this paper, a fault diagnostic method using modularized knowledge was proposed, a fault diagnostic system was constructed for an experimental plant, and the effectiveness of this method was clarified by carrying out a fault diagnostic experiment. The characteristics of the proposed fault diagnostic system were as follows: The necessary knowledge for diagnosing faults was made into each process element. Based on this method, the revision and addition of a knowledge base could be carried out in each element, and the design change of a plant could be flexibly corresponded by only changing the related part of the process flow graph. The estimated results were stored into the working memory, not only faults of an element in which faults resulted could be estimated, but also the fault propagating path could be clarified. 8 refs., 6 figs., 3 tabs.

  2. Kas Haapsalu asub Marsil? / Tanel Veenre

    Index Scriptorium Estoniae

    Veenre, Tanel, 1977-

    2011-01-01

    Prantsuse kunstnike Nicolas Schneideri ja Antoine Lejolivet' näitus "Ükskord me kõnnime Marsil" ehk "On ira marcher sur Mars" Haapsalus Evald Okase muuseumis 31. augustini 2011. Näitusele eelnes kunstnike kahenädalane residentuur muuseumis. Projekti eestvedaja Mara Koppel-Ljutjuk

  3. Relative amplitude preservation processing utilizing surface consistent amplitude correction. Part 3; Surface consistent amplitude correction wo mochiita sotai shinpuku hozon shori. 3

    Energy Technology Data Exchange (ETDEWEB)

    Saeki, T [Japan National Oil Corporation, Tokyo (Japan). Technology Research Center

    1996-10-01

    For the seismic reflection method conducted on the ground surface, generator and geophone are set on the surface. The observed waveforms are affected by the ground surface and surface layer. Therefore, it is required for discussing physical properties of the deep underground to remove the influence of surface layer, preliminarily. For the surface consistent amplitude correction, properties of the generator and geophone were removed by assuming that the observed waveforms can be expressed by equations of convolution. This is a correction method to obtain records without affected by the surface conditions. In response to analysis and correction of waveforms, wavelet conversion was examined. Using the amplitude patterns after correction, the significant signal region, noise dominant region, and surface wave dominant region would be separated each other. Since the amplitude values after correction of values in the significant signal region have only small variation, a representative value can be given. This can be used for analyzing the surface consistent amplitude correction. Efficiency of the process can be enhanced by considering the change of frequency. 3 refs., 5 figs.

  4. Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Tsukui, R; Tsuru, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1996-10-01

    For the physical modeling system of Technology Research Center, Japan National Oil Corporation, data acquisition on the ocean and ground can be simulated using models. This system can provide data for verification of the data processing and elastic wave simulation algorithm. This can also provide data for decision of experiment specifications by making a model simulating the underground structure of the given test field. The model used for the physical modeling system is a gradient multilayer model with six-layer structure. Depth migration before stacking was conducted using data obtained through two acquisition methods, i.e., up-dip acquisition and down-dip acquisition. The depth migration before stacking was performed for data obtained by up-dip acquisition in addition to the records obtained by down-dip acquisition. Consequently, a definite reflection surface was observed, which has not been observed from the processing results of down-dip acquisition data. 9 figs.

  5. Environmental assessment of surfactant using aquatic microcosm system; Konuma no suiken seitaikei ni oyobosu kaimen kasseizai no microcosm system wo mochiita hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Takamatsu, Y.; Matsumura, M. [University of Tsukuba, Tsukuba (Japan); Inamori, Y. [National Institute for Environmental Studies, Tsukuba (Japan); Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering

    1995-10-10

    Microcosm system was applied to assess effect of surfactants on aquatic ecosystem. Surfactants such as LAS and Soap were added to an aquatic flask-size microcosm consisting of four species of bacteria as decomposer, one species of ciliate protozoa (Cyclidium glaucoma), two rotifers (Philodina sp. and Lepadella sp.) and one aquatic oligochaete (Aeolosoma hemprichi) as predator, and a green alga (Chlorella sp.) and a filamentous blue-green alga (Tolypothrix sp.) as producer. In the system, NOEC (no observed effect concentration) of LAS was below 1.5mg{center_dot}l{sup -1}, whereas soap was below 30mg{center_dot}l{sup -1}. Microcosm test is a pertinent tool to assess the effect of surfactant on ecosystem because microcosm test makes it possible to evaluate the effect of surfactant from a viewpoint of the interaction of microorganisms, material cycle and energy flow. With these respects, microcosm test is useful environmental assessment method which can reflect aquatic ecosystem. 10 refs., 6 figs., 1 tab.

  6. Ecological effects assessment of anionic surfactant on aquatic ecosystem using microcosm system; Microcosm wo mochiita in ion kaimen kasseizai no suiken seitaikei ni oyobosu eikyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Takamatsu, Y. [University of Tsukuba, Tsukuba (Japan); Inamori, Y. [National Institute for Environmental Studies, Tsukuba (Japan); Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering; Kurihara, Y. [Ou Univ., Fukushima (Japan). Faculty of Engineering; Matsumura, M. [University of Tsukuba, Tsukuba (Japan). Institute of Applied Biochemical

    1997-11-10

    Microcosm system was applied to assess effect of anionic surfactant (LAS) on aquatic ecosystem. Anionic surfactant such as LAS was added to an flask microcosm consisting of four species of bacteria as decomposer, one species of ciliate protozoa (Cyclidium glaucoma), two rotifers (Philodina sp. and Lepadella sp.) and one aquatic oligochaete (Aeolosoma hemprichi) as predator, and a green alga (Chlorella sp.) and a filamentous blue-green alga (Tolypothrix sp.) as producer, comparing with that of an natural lake model ecosystem derived from natural lake water. In the flask microcosm system and the natural lake model ecosystem, biodegradation rates of LAS were almost same and NOECs (no observed effect concentration) of LAS were also below 1.5 mg{center_dot} l{sup -1}. It was found that flask microcosm test could provide precise ecological effect assessment of LAS on number of microorganisms because the system showed higher reproducibility and stability than natural take model ecosystem. It was suggested that flask microcosm test was useful ecological effect assessment method which can reflect natural aquatic ecosystem. 10 refs., 4 figs., 2 tabs.

  7. Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Tsukui, R; Tsuru, T [Tech. Research Center, Japan National Oil Corp., Tokyo (Japan); Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1996-05-01

    The Physical Modeling System introduced into the Technology Research Center, Japan National Oil Corporation, and data collected by use of the system are presented. The Physical Modeling System is 10,000 times smaller than the real one, comprising a water tub section, measuring device section, and control section, etc. The water tub section comprises a tub for housing the model, transducers for transmitting and receiving vibration, controllers, etc. The water tub measures 1.8{times}1.2{times}0.9m. The model used in the experiment is an `inclined multilayer model` with each of its six layers pinching out toward the top, and is usable for the comparison of various migration methods. In one case in the records, reception was made at 184 reception points deployed at intervals of 3mm, when the minimum offset was 15mm and the maximum offset 564mm. Nothing very obvious was observed when the ordinary overlapping of DMO and CDP was applied to this record, which suggests that pre-overlapping migration treatment is required. 5 figs.

  8. Digital data storage of core image using high resolution full color core scanner; Kokaizodo full color scanner wo mochiita core image no digital ka

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, W; Ujo, S; Osato, K; Takasugi, S [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan)

    1996-05-01

    This paper reports on digitization of core images by using a new type core scanner system. This system consists of a core scanner unit (equipped with a CCD camera), a personal computer and ancillary devices. This is a modification of the old type system, with measurable core length made to 100 cm/3 scans, and resolution enhanced to 5100 pixels/m (1024 pixels/m in the old type). The camera was changed to that of a color specification, and the A/D conversion was improved to 24-bit full color. As a result of carrying out a detail reproduction test on digital images of this core scanner, it was found that objects can be identified at a level of about the size of pixels constituting the image in the case when the best contrast is obtained between the objects and the background, and that in an evaluation test on visibility of concaves and convexes on core surface, reproducibility is not very good in large concaves and convexes. 2 refs., 6 figs.

  9. On-line measurement of crystalline color by color-image processing system; Gazo shori system wo mochiita kessho no online iro sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Okayasu, S.; Katayama, M.; Shinohara, T. [Ajinomoto Co. Inc., Tokyo (Japan)

    1996-01-20

    Aiming for the stable operation and the rationalization of factory plant, the color-image processing has been tried to introduce into the on-line system to measure the crystalline color of L-Lysine in its refining process. Because the practical spectro-photometry was used to be employed by manual measurement. In this paper, the calculation formula of the transmittance by spectrophotometry is theoretically introduced by analyzing the relation of Lambert-Beer`s law of luminous transparency with the Kubelka-Munk`s function of the luminous dispersion using color image data. The parameters of the calculation formula were decided by actual measurement, so that the formula with accuracy value of {plus_minus}3% elucidated the possible estimation of transmittance by spectrophotometry. The system was tested on a commercial plant, and some issues are discussed. 8 refs., 8 figs., 3 tabs.

  10. Estimation of hydrogen bondings in coal utilizing FTir and differential scanning calorimetry (DSC); FTir to DSC wo mochiita sekitannai suiso ketsugo no teiryoteki hyoka no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Mae, K.; Miura, K. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1996-10-28

    With an objective to know coal condensation structure which has influence on coal conversion reaction, an attempt was made on quantitative evaluation of hydrogen bonding in coal. Using as test samples the VDC made from Taiheiyo coal swollen by tetralin and vacuum-dried, and its pyrolyzed char, DSC measurement and Fourier transform infrared spectroscopy (FT) were performed. An FT spectrum comparison revealed that the VDC swollen at 220{degree}C has the hydrogen bonding relaxed partly from the original coal. However, since the change is in a huge coal molecular structure restraining space, it has stopped at relaxation of the bonding energy without causing separation as far as free radicals. On the other hand, the DSC curve shows that the VDC has slower endothermic velocity than the original coal. In other words, the difference in heat absorption amounts in both materials is equivalent to the difference of enthalpy ({Delta} H) of both materials, which corresponds to the relaxation of the hydrogen bonding. Therefore, the {Delta} H was related to wavenumber shift of the FT spectra (which corresponds to change in the hydrogen bonding condition). By using this relationship, a method for evaluating hydrogen bonding distribution was proposed from an O-H contracting vibration change that can be measured by using the FT spectra and a thermal change that can be measured by using the DSC. 3 refs., 7 figs.

  11. Development of liquefaction process of coal and biomass in supercritical water; Chorinkaisui wo mochiita sekitan biomass doji ekika process no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nonaka, H.; Matsumura, Y.; Tsutsumi, A.; Yoshida, K. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Masuno, Y.; Inaba, A. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    Liquefaction of coal and biomass in supercritical water has been investigated, in which strong solubilization force of supercritical water against hydrocarbons is utilized. Free radicals are formed through the cleavage of covalent bonds in coal under the heating condition at around 400{degree}C during coal liquefaction. It is important to stabilize these unstable intermediate products by hydrogen transfer. On the other hand, hydrogen is not required for the liquefaction of biomass having higher H/C atomic ratio and oxygen content than those of coal. Co-liquefaction of coal and biomass was conducted using supercritical water, in which excess hydrogen from the liquefaction of biomass would be transferred to coal, resulting in the effective liquefaction of coal. Mixture of coal and cellulose was liquefied in supercritical water at 390{degree}C under the pressure of 25 MPa using a semi-continuous reactor, and the results were compared with those from the separate liquefaction of them. The co-liquefaction of coal and cellulose did not show any difference in the residue yield from the separate liquefaction of these, but led to the increased production of compounds with lower molecular weight. The liquefaction was completed in 15 minutes. 5 refs., 3 figs., 3 tabs.

  12. Monitoring on-line system for the lactic fermentation measurement using the integration enzyme sensor; Shusekika koso sensa wo mochiita nyusan hakko keisokuyo onrain monitringu shisutemu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Masayasu; Kumagaya, Tsuyoshi; Nakajima, Yoichi [Kyushu Institute of Technology, Fukuoka (Japan)

    1999-04-05

    The monitoring on-line system for the lactic fermentation measurement in which the simultaneous measurement of the substrate. Generation was possible was constructed without consuming the culture medium by using soliciting small enzyme sensor and flow injection analysis system integrate. There was the linearity that anyway was also range of concentration of 70mM or less and that it is good on the calibration curve of minute glucose, lactose, and lactic acid sensor. It became clear that it proved that all range of concentration of the substrate of these three which combining with the micro diary system, breaks in the lactic fermentation measurement with the necessity can be measured and not observe the interference by medium components, etc. either. Constructed monitoring on-line system is Lactobacillus delbrueckii and, it was applied to the lactic fermentation process of Lactobacillus lactis. Through the fermentation process for 24 hours, simultaneous measurement of glucose (or lactose) and lactic acid is possible. The measured value agreed well with the result of colorimetric method using the enzyme. (translated by NEDO)

  13. On-line monitoring system of lactic acid fermentation by using integrated enzyme sons ors; Shusekika koso sensa wo mochiita nyusan hakko keisokuyo onrain monitaringu shisutemu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Masayasu; Kumagi, Takeshi; Nakashima, Yuuichi [Kyushu University, Fukuoka (Japan). Dept. of Biochemical Engineering and Science

    1999-03-10

    An on-line monitoring system for lactic acid fermentation is developed by using integrated micro enzyme sensors, a flow injection analysis system, and a micro dialysis system. The calibration curves of micro glucose, lactose and lactate sensors show good linearity in the concentration range below 70 mM. By combination with the micro dialysis system, the enzyme sensors can measure the whole concentration range of lactic acid fermentation, and interference by the medium can not be observed. The on-line sensor system is then applied to lactic acid fermentation of Lactobacillus delbrueckii. The sensor system can monitor the glucose and lactate concentrations simultaneously during 24-h fermentation, and the measurements show good agreement with those of the conventional colorimetric method. The sensor system can also be applied to on-line monitoring of lactose and lactate during Lactobacillus lactis fermentation. (author)

  14. FY1995 development of economical and high efficient desulfurization process using low rank coal; 1995 nendo teitankadotan wo mochiita ankana kokoritsu datsuryuho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The objective of this study is to develop a new efficient desulfurization technique using a Ca ion-exchanged coal prepared from low rank coal and calcium raw material as a SO{sub 2} sorbent. Ion-exchange of calcium was carried out by soaking and mixing brown coal particles in milk of lime or slurry of industrial waste from concrete manufacture process. About 10wt% of Ca was easily incorporated into Yallourn coal. The ion-exchanged Ca was transformed to ultra-fine CaO particles upon pyrolysis of coal. The reactivity of CaO produced from Ca-exchanged coal to SO{sub 2} was extraordinary high and the CaO utilization of above 90% was easily achieved, while the conversion of natural limestone was less than 30% under the similar experimental conditions. High activity of Ca-exchanged coal was appreciably observed in a pressurized fluidized bed combustor. Ca-exchanged coal was quite effective for the removal of hydrogen sulfide. (NEDO)

  15. Development of new peptide synthetic method of enzyme using the extraction reactivity; Chushutsu hanno wo mochiita shiki pepuchido koso goseiho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hirata, Makoto [Oita University, Oita (Japan)

    1999-03-05

    Recently, taste and bioactivation of large number of oligopeptide become clear, and the development of the efficient synthetic method becomes the urgency. In the production process by conventional enzyme reaction which combined the crystallization, because the solubility of the product to the water which is reaction solvent is low, the yield remained at about 60%, and the problem of reaction inhibition of the product by the crystal had also been indicated. In the enzyme synthesis of the aspartame in which he is the representative oligopeptide, it aimed at the establishment of the new synthesis method which can improve yield and reaction rate, while the segregation enzyme was continuously utilized. In this synthetic method, supply of organic solvent which dissolved the substrate, extraction of the substrate from organic solvent to water phase, synthesis reaction by the segregation enzyme in water phase, extraction of the aspartame which is a product from water phase to organic solvent progress, and they continuously progress by one complete mixing reactor. The process which controlled these speeds and yields was quantitatively analyzed, and material balance style considering substrate, enzyme and mass transfer of the product and enzyme reaction speed was deduced. The optimum operating condition for improving yield and productivity of the purpose product using this solution was examined, and optimum supply concentration and agitation speed of aspartic acid which was a substrate were started, and the optimum operating condition which realizes the improvement in high yield and productivity over 90% of the aspartame was clarified. Like this, it is that this research adopts features of liquid Citrus nobilis two-phase partition for the enzyme synthesis of the aspartame, and it is considered that there is a value, because it is the creative research which verified that the productivity can be greatly improved by the utilization of the chemical-engineering technique, and because the industrial contribution is also big. (translated by NEDO)

  16. FY1995 research on nonlinear optical devices using super-lattice semiconductors; 1995 nendo chokoshi active hisenkei soshi wo mochiita chokosoku hikari seigyo gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose is to develop technologies on efficient generation and control of femtosecond optical pulses using a novel semiconductor optical devices. We studied a modelocked Cr:forsterite laser pumped by a diode pumped Nd:YVO4 laser. Both Kerr lens mode locking and semi-conductor saturable absorber initiated mode locking have been achieved. The minimum pulse width for pure Kerr lens mode locking is 26.4 fs, while for the semiconductor saturable absorber initiated mode locking, the pulse width is 36 fs. The latter is very resistant to the environment perturbations. We also present the measured dispersion data for the forsterite crystal and the SESAM, and discuss the dispersion compensation technique. (NEDO)

  17. Emission behavior of OH radical in internal EGR using a 2-cycle engine; 2 cycle engine wo mochiita naibu EGR no OH radical no hakko kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, S; Amino, Y; Yoshida, K; Shoji, H; Saima, A [Nihon University, Tokyo (Japan)

    1997-10-01

    The purpose of this study was to examine and consider the influence, which the remained gas exercised on combustion. 2-cycle engine was Used as the test engine. Internal EGR was run. The means was that the test engine was fitted the back pressure control plate on the exhaust port. The conditions, which were run with internal EGR and without internal EGR, were compared. The OH radical, which plays important role in combustion of hydrocarbon fuels, was measured with emission spectroscopy. In internal EGR, the unburned end gas on exhaust port side was susceptible to the remained gas. 6 refs., 8 figs., 1 tab.

  18. Toxicity evaluation of chlorinated organic compounds using immortalized rat hepatocytes; Fushika rat kansaibo wo mochiita yuki enso kagobutsu no dokusei hyoka no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Sone, H; Nakajima, M; Yonemoto, J [National Institute for Environmental Studies, Tsukuba (Japan)

    1997-11-10

    Chlorinated organic compounds has high priority for toxicity screening among environmental hazardous chemicals. In the present study, we used immortalized rat hepatocytes as a liver model in vitro to evaluate the toxicity of nine chlorinated organic compounds. Toxicity of nine chlorinated organic compounds were evaluated to cellular viability of immortalized rat hapatocytes. The potency of the toxicity based on 50% inhibitory concentration (IC50) value was in the following order: triclocalban>triclosan>3,4-dichloroaniline>2,5-diclorophenol> 2,5-dichloroanisole>p-dichlorobenzene> p-chloroaniline>o-dichlorobenzene=tris (2-chloroethyl) phosphate. The rank order of cytotoxic potency of nine chemicals was compared with toxicity information using animals. The rank order of cytotoxic potency did not relative to the order referenced mean lethal dose (LD50) as an index of acute toxicity of rats or mice. However, the rank order of cytotoxic potency relatively correlated non-observed adverse effect level (NOAEL) under the exposure duration adjusted for chronic toxicity in vivo. These data suggests that the origin of testing cell had better to make match target organ of toxic chemicals for extrapolation from data of bioassay in vitro to in vivo. 16 refs., 2 figs., 3 tabs.

  19. Crossflow type silicon microchannel substrate monodispersion oil-in-water emulsion manufacture; Kurosufuro gata shirikon maikuro chaneru kiban wo mochiita tanbunsan suchuyu emarushon no sakusei

    Energy Technology Data Exchange (ETDEWEB)

    Kawakatsu, Takahiro [Tohoku University, Miyagi (Japan). Graduate School; Komori, Hideai; Najima, Mitsutashi; Kikuchi, Yuji; Yonemoto, Toshikuni

    1999-05-05

    The new technique, which continuously produced the monodispersion oil-in-water (0/W) emulsion using the crossflow type silicon microchannel substrate, was developed. On the silicon monocrystal substrate, the watercourse as the liquid of the continuous phase flowed was produced, and the column of the equal slit of the size in both walls of the watercourse was precisely processed. By closing the upper part in the slit by the clamp of the flat glass board in the microchannel substrate, the microchannel column was formed. Through the microchannel, the oil droplet in which the size was even was formed by sending out the oil (triolein) in the water (0.3wt% sodium lauryl sulfate aqueous solution) of continuous phase which is flowing in respect of the watercourse. The size of the oil droplet is greatly dependent on the structure of the microchannel regulated by microchannel width, microchannel height and terrace length (the even part of which the microchannel exit was equipped). Monodispersion emulsion of 16,20 and 48 {mu}m at the average droplet diameter was formed by using microchannel substrate of the three types of which the structure differs. Droplet diameter decreased, when the substrate which formed large droplet of 48 {mu}m in which the water current quantity is 1.4x10{sup -2}mLmin{sup -1} was used, when the flow rate increased. However, there was no a flow rate at droplet diameter, even if it was made to change from 1.4x10{sup -2} to 2.4mLmin{sup -1}, 16 {mu}m 20 {mu}m small change. In all cases, the droplet size distribution was narrow, and the geometry standard deviation was under 1.03. (translated by NEDO)

  20. Hydrogen storage alloy electrode and the nickel-hydrogen secondary battery using the electrode; Suiso kyuzo gokin denkyoku to sorewo mochiita nikkeru/suiso niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Ono, T. [Furukawa Electric Co. Ltd., Tokyo (Japan); Furukawa, J. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

    1997-02-14

    With respect to the conventional nickel-hydrogen secondary battery, pulverization of the hydrogen storage alloy due to repetition of charging-discharging cycles can be prevented by using a fluorocarbon resin as a binder in manufacture of the hydrogen storage alloy electrode; however, the inner pressure increase of the battery in case of overcharging can not be fully controlled. The invention relates to control of the inner pressure increase of the nickel-hydrogen secondary battery in case of overcharging. As to the hydrogen storage alloy electrode, the compound comprising the hydrogen storage alloy powder as a main ingredient is supported by a current collector; further, the compound particularly comprises a fluororubber as a binder. The nickel-hydrogen secondary battery equipped with the hydrogen storage alloy electrode can control the inner pressure increase of the battery in case of overcharging, and lessen decrease of the battery capacity due to repetition of charging-discharging cycles over long time. The effects are dependent on the use of the fluororubber as a binder which has good flexibility, and strong binding capacity as well as water repellency. 1 tab.

  1. Calculation of wave resistance by using Kochin function in the Rankine source method; Rankinsosuho ni okeru kochin kansu wo mochiita zoha teiko keisan

    Energy Technology Data Exchange (ETDEWEB)

    Yasukawa, H [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1997-10-01

    In order to avoid negative wave resistance (which is physically incomprehensible) generated in calculating wave resistance by using the Rankine source method, a proposal was made on a wave resistance calculation method using the Kochin function which describes behavior of speed potential in regions far apart from a hull. The Baba`s condition was used as a free surface condition for the speed potential which expresses wave motions around a hull. This has allowed a new Kochin function which uses as unknown the speed potential on the hull surface and the free surface near the hull to be defined and combined with the Rankine source method. A comparison was made between the calculated values for wave resistance, hull subsidence and trim change of an ore transporting vessel (SR107 type of ship) in a fully loaded condition and the result of water tank tests. The wave resistance values derived from pressure integration have all become negative when the Froude number is from 0.1 to 0.2, while no negative resistance has appeared in the calculations by using the Kochin function, but the result has agreed with that of the water tank tests. Accuracy of the calculations at low speeds was improved. The trim change in the calculations was slightly smaller than that in the water tank tests. The subsidence showed a good agreement. 7 refs., 1 fig.

  2. Study on properties of mortar using silica fume and ground blast furnace slag. Silica fume oyobi koro slag funmatsu wo mochiita mortar no tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shiiba, H; Honda, S; Araki, A [Fukuoka University, Fukuoka (Japan). Faculty of Engineering

    1992-09-01

    The effect of silica fume and ground blast furnace slag in concrete on the content of superplasticizer, and dynamic properties of hardened mortar with such admixtures were studied experimentally. Although the dependence of a flow value on the superplasticizer was dominated by kinds of superplasticizers, blast furnace slag enhanced the flow value resulting in a high fluidity. Adsorption of superplasticizers onto admixtures was dependent on kinds of superplasticizers, and adsorption onto blast furnace slag was 1.3-2 times that onto normal Portland cement (NPC). The compressive strength of mortar increased by mixing admixtures, while the bending strength was enhanced only by mixing silica fume. Mixing mortar was lower in dynamic elastic modulus than NPC mortar at the same compressive strength, and the velocity of supersonic wave in mortar was scarcely affected by mixing. 11 refs., 14 figs., 3 tabs.

  3. Analysis of crashes using FE vehicle models. Relations between vehicle types and crash characteristics; Yugen yoso model wo mochiita sharyo no shototsu kaiseki. Sharyo type to shototsu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Takatori, O. [Japan Automobile Research Institute Inc., Tsukuba (Japan)

    2000-01-01

    The objective of this study is to analyze the crash characteristics of vehicles under the condition of real-world accidents. This paper pays attention to the differences in the crash characteristics of a vehicle colliding with a vehicle which is a different type. Vehicles on the market can be divided broadly into two vehicle structures, monocoque structure and frame structure. Monocoque structure is mainly used for passenger vehicles and frame structure is for recreational vehicles (RV). In recent years, RV has been a large seller on the market. So accidents between passenger vehicles and a RVs occur frequently. The analysis of experimental data and computer simulation, which is predicated on the experimental data, was carried out for this study. In the analysis of experimental data, barrier force data from the New Car Assessment Program (NCAP) were analyzed. The FE passenger vehicle model which is based on systematic validation tests was used for the computer simulation of car-to-car collisions. (author)

  4. Research on active magnetic levitation of multiple high-T{sub c} superconductors; Fukusu no baruku chodendotai wo mochiita akuteibu jikifujo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nishi, K.; Tachi, K.; Sawa, K. [Keio University, Tokyo (Japan); Iwasa, K. [Francis Bitter Magnet Laboratory, Cambridge (United States); Nagashima, K.; Fujimoto, H. [Railway Technical Research Institute, Tokyo (Japan); Miyamoto, T.; Tomita, M.; Murakami, M. [Superconducting Research Laboratory, Tokyo (Japan)

    1999-11-25

    This paper describes a new [electromaglev] system, in which multiple Y-Ba-Cu-O bulk superconductors are levitated on a DC magnet. In this system, we have succeeded in controlling the levitation height and force like the case of a single bulk system. We also simulated the total levitation force for multiple bulks, which were in good agreement with the experimental results. (author)

  5. Stochastic model of flow and dispersion of fine particles in a packed bed; Kakuritsu katei wo mochiita juten sonai deno funtai no ryudo to bunsan model

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, K [Kawasaki Steel Corp., Tokyo (Japan); Lockwood, F

    1996-06-01

    For the calculation of pulverized coal combustion in a blast furnace blow pipe and tuyere, a model was built for the evaluation of the movement and dispersion of particles in a packed bed by use of a stochastic approach. In the stochastic particle trajectory calculation taking into consideration the impact of fluctuations in gas turbulence, interaction distance between particles and eddies and interaction time have to be determined, in addition to fluctuations in gas flow velocity (to be determined by measuring the instantaneous flow velocity in a normal distribution generated according to random numbers). The eddy life was determined using Shuen`s formula on the premise that the particle-eddy interaction occurs within the calculated life or the transit time, whichever is shorter. As for the turbulence energy {kappa}, it was determined by the {kappa}-{epsilon} model for the free space and by the {kappa}-Lm(mixing length) model for the packed bed. From the average of a multiplicity of particles in the experiment, such time average specific values as the average density and flow velocity vectors of particles in the space, and particle trajectories, were calculated, which proved to agree with values from experiments. Once in the packed bed, the pulverized coal underwent a sudden deceleration due to its interaction with particles in the packed bed, and the pulverized coal flow near the central axis was rapidly diffused in the packed bed. This model is expected to find its use in the study of pulverized coal combustion in the blast furnace. 18 refs., 12 figs., 2 tabs.

  6. Gas flow calculation with a turbulence model in a packed bed; Ranryu model wo mochiita juten sonai no gas nagare no keisan

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, K [Kawasaki Steel Corp., Tokyo (Japan); Lockwood, F

    1996-06-01

    For the rationalization of blast furnace operation, the gas flow in a packed bed is calculated using a turbulence model. For accurately determining the mixing of gasses, dispersion of particulates in a turbulence, turbulence diffusion, response rate, etc., in a packed bed, turbulence characteristics need be elucidated. For the calculation of combustion behavior of powdered coal blown into the blast furnace tuyere, in particular, the evaluation of gas turbulence behavior in the blow pipe and packed bed is indispensable. The dissipation rate of {kappa} has been defined from the mixing length Lm with the hydraulic diameter of the packed bed as its function and the turbulence energy ({kappa}), and now a {kappa}-Lm model is proposed, capable of evaluating the turbulence behavior in the packed bed. The parameters in the model may be determined using the actually measured values about diffusion behavior. The diffusion behavior of a tracer blown into the packed bed is simulated, and then agreement is found between the calculated values and measured values. Oxygen distribution under simplified raceway conditions is calculated. Once in the raceway, the radial concentration gradient of oxygen is much gentler suddenly, indicating the excellent mixture characteristics of the packed layer. 21 refs., 9 figs.

  7. Study on particle behavior in the expansion of fluidized bed using a simple optical probe. Kogaku probe wo mochiita ryudoso no bocho sonai ryushi kyodo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kato, Y; Miyamoto, M [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering; Chimura, T [Toyota Motor Co. Ltd., Tokyo (Japan); Idei, Y [Ube Industries, Ltd., Tokyo (Japan)

    1991-09-25

    In order to clarify the relationship between the heat transfer rate and the expansion bed in a group of horizontal pipes in a freeboard region (an area of the heat-transfer pipe exposed above the height of static particle bed from the beginning) in a cold model of the fluidized bed, particle behavior was measured using an optical measuring method. The light axis position was set higher than the heat-transfer as X {sub p} in a direction perpendicular from the distributor, and the static bed height was set to L {sub c}. The frequency of particles and particle lumps coming to presence between the light axes is termed V {prime}{sub p}(time-averaged dimensionless amount of the optical probe output). The V {prime}{sub p} decreases with an increase in the flow velocity, and, when the difference between the probe tip and the static bed height, X {sub p}{minus} L {sub c} is small, it shows the minimum value at a certain flow velocity and then rises again. The root mean square value of the probe output, V {prime}{sub f} increased with an increase in the flow velocity, reached its maximum, then decreased to the minimum, and rose again. The flow velocity that takes the maximum heat transfer rate can be identified from the relationship among the dimensionless amount of the maximum expansion bed height and the average expansion bed height, the dimensionless height of X {sub p} when V {prime}{sub p} and V {prime}{sub f} obtained at each X {sub p} show the extreme values, and the dimensionless height of the heat-transfer pipes when the average transfer rate takes the maximum value. 6 refs., 5 figs.

  8. Estimation of durability of GFRP laminates under stress-corrosive environments using acoustic emission; AE wo mochiita ouryoku fushoku kankyoka deno GFRP no taikyusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, Yoshimichi. [Seikow Chemical Engineering and Machinery, Ltd., Hyogo (Japan). Laboratory of Composite Materials; Nishiyabu, Kazuaki. [Osaka Prefectural College of Tehcnology, Osaka (Japan)

    1999-05-15

    The objective of this investigation is to estimate the creep life of glass fiber reinforced plastic (GFRP) under stress-corrosive environments using acoustic emission(AE). The laminates were fabricated using combinations of vinylester resin (R806) and random fiber mat or woven cloth. The creep tests were conducted in 5% nitric acid (HNO{sub 3}) environment. The AE depends on the loading level and the environment condition. For the creep test, the woven cloth reinforced specimens gave higher number of AE counts than the random mat reinforced specimens. The creep life decreased with increasing creep stress, whereas the rate of AE counts increased with increasing creep stress. A linear relationship was found between the creep life and the AE count rate. Using the proposed equation, a prediction of the creep life of GFRP under corrosive environments would presumably be possible. (author)

  9. Geoelectric study in attempt to detect of deformation around slice gate in the embankment; Hiteiko eizoho wo mochiita himon shuhen no yurumi ryoiki no suitei

    Energy Technology Data Exchange (ETDEWEB)

    Natori, T; Nakayama, Y [Hokkaido Sapporo Public Works Office, Sapporo (Japan); Hashimoto, Y; Matsuo, J [OYO Corp., Tokyo (Japan)

    1997-10-22

    For the river structures, such as slice gates and slice pipes, constructed on the weak ground, structures often come out due to forced settlement of embankment, which results in the formation of cavity and loose ground. These deformations can cause disasters due to leakage by water channel and fracture of bank. It is significant to detect and grasp these situations in early stage. In this study, resistivity imaging was conducted around slice gate in several times, to estimate the loose region based on the difference in the obtained resistivity data. Resistivity was measured in two times with a certain interval using the same line. The loose region around the slice gate was estimated from the change of saturation condition and the saturation line by considering the difference. Even in the case when judgment was hard by a single measurement, it was possible to estimate the loose region based on the difference from multiple measurements. 3 refs., 6 figs.

  10. Resistivity tomography using borehole of 500m in depth at the seaside site; 500m shin boring wo mochiita kaigan fukin deno hiteiko tomography tansa

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, K [Central Research Institute of Electric Power Industry, Tokyo (Japan); Kono, T [Radioactive Waste Management Center, Tokyo (Japan); Chiba, A [Sumitomo Metal Industries, Ltd., Osaka (Japan)

    1997-10-22

    With an objective to verify exploration methods to identify geological structures to a depth of about 500 m and continuity of fissure zones, a case study was carried out on a resistivity tomography method using ground surface exploration by means of the resistivity method and boreholes of 500 m in depth. The investigated area is consisted of abyssal rocks of the Cretaceous period, where granodiorites of coarse grain and intrusive rocks of small scale are distributed. Fissures on the ground surface have gentle inclination, and are of opening type showing high water permeability. The data analysis has derived apparent resistivities in the Wenner electrode arrangement, the Eltran electrode arrangement and the pole-pole electrode arrangement. The resistivity tomography has derived apparent resistivity in the pole-dipole electrode arrangement which is relatively high in accuracy and strong against noise. As a result of inputting these resistivities and performing an analysis on a two-dimensional resistivity structure, a structure of 100-m scale was made clear, in which difference of the resistivity values is distinct. The result of the resistivity tomography may be thought to have identified the resistivity anomaly of a small scale, although the absolute values show some variation. 4 refs., 5 figs., 2 tabs.

  11. Imaging of in-tunnel horizontal seismic profile using three-component accelerometers; Sanseibun kaoskudokei wo mochiita tunnel HSP no imaging

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, S [Nippon Geophysical Prospecting Co. Ltd., Tokyo (Japan); Isahai, H [Kumagai Gumi Co. Ltd., Tokyo (Japan); Inazaki, T; Kurahashi, T [Public Works Research Institute, Tsukuba (Japan); Hagiwara, I [Suncoh Consultant Co. Ltd., Tokyo (Japan)

    1997-10-22

    Analysis was made on data of measurements using three-component accelerometers for horizontal seismic profile (HSP) exploration as a method to investigate tunnel front, under a limited condition of work to be done inside a tunnel shaft. The analysis was intended to discuss feasibility of determining the reflection face. In the experiment, courses of traverse for the exploration were set on side walls, and vibration receiving and transmitting points were arranged. The courses of traverse had 22 in-tunnel seismographs installed at an interval of 1.5 m. The HSP processing has used three-component measurement records derived from three vibration transmitting points. After giving a pre-treatment, only the outward wave and inward wave components were extracted by applying a velocity filter as a method to separate the wave motion fields. A migration treatment was given on the inward wave component by using the GRT method to have derived position, direction and inclination of the obliquely crossed reflection face. As a result of having performed a comparison with the result of tunnel wall observation, distribution of the direction and inclination of the reflection face derived from the reflection intensity was found consistent with the distribution of direction and inclination of fissures and bedding planes obtained from the tunnel wall observation. Thus, a unique decision was concluded possible. 5 refs., 8 figs., 1 tab.

  12. Relative amplitude preservation processing utilizing surface consistent amplitude correction. Part 4; Surface consistent amplitude correction wo mochiita sotai shinpuku hozon shori. 4

    Energy Technology Data Exchange (ETDEWEB)

    Saeki, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-10-22

    Discussions were given on seismic exploration from the ground surface using the reflection method, for surface consistent amplitude correction from among effects imposed from the ground surface and a surface layer. Amplitude distribution on the reflection wave zone is complex. Therefore, items to be considered in making an analysis are multiple, such as estimation of spherical surface divergence effect and exponential attenuation effect, not only amplitude change through the surface layer. If all of these items are taken into consideration, burden of the work becomes excessive. As a method to solve this problem, utilization of amplitude in initial movement of a diffraction wave may be conceived. Distribution of the amplitude in initial movement of the diffraction wave shows a value relatively close to distribution of the vibration transmitting and receiving points. The reason for this is thought because characteristics of the vibration transmitting and receiving points related with waveline paths in the vicinity of the ground surface have no great difference both on the diffraction waves and on the reflection waves. The lecture described in this paper introduces an attempt of improving the efficiency of the surface consistent amplitude correction by utilizing the analysis of amplitude in initial movement of the diffraction wave. 4 refs., 2 figs.

  13. Wave fields simulation in difficult terrain using numerical grid method; Hyoko henka no aru chiiki deno suchi koshi wo mochiita hado simulation

    Energy Technology Data Exchange (ETDEWEB)

    Jung, W; Ogawa, T [Yokohama National University, Yokohama (Japan); Tamagawa, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1997-10-22

    This paper describes that a high-accuracy simulation can be made on seismic exploration by using the numerical grid method. When applying a wave field simulation using the difference calculus to an area subjected to seismic exploration, a problem occurs as to how a boundary of the velocity structure including the ground surface should be dealt with. Simply applying grids to a boundary changing continuously makes accuracy of the simulation worse. The difference calculus using a numerical grid is a method to solve the problem by imaging a certain region into a rectangular region through use of variable conversion, which can impose the boundary condition more accurately. The wave field simulation was carried out on a simple two-layer inclined structure and a two-layer waved structure. It was revealed that amplitudes of direct waves and reflection waves are disturbed in the case where no numerical grid method is applied, and the amplitudes are more disperse in the reflection waves than those obtained by using the numerical grid method. 7 refs., 10 figs.

  14. Solubilization of lignite and behavior of oxygen containing functional groups in coal with superacid; Chokyosan wo mochiita kattan no kayoka oyobi sanso kannoki no kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, K.; Saito, I. [National Institute for Resources and Environment, Tsukuba (Japan); Sasaki, S.; Suganuma, A. [Science University of Tokyo, Tokyo (Japan). Faculty of Science and Technology

    1996-10-28

    Solubilization of lignite including a large amount of oxygen containing functional groups was attempted using HF/BF3, and the behavior of oxygen containing functional group, one of the important factors for coal liquefaction, was studied. In experiment, the cooled slurry of Yallourn coal specimen and solvent (toluene, isopentane) was filled into a vacuum autoclave together with HF/BF3. Reaction was performed under spontaneous pressure at 50, 100 or 150{degree}C for 3 hours. The distribution of oxygen containing functional groups in each coal specimen was determined by quantification of carboxyl group, hydroxyl group and carbonyl group. As the experimental result, the superacid mixture of HF and BF3 considerably improved the solubility of coal specimens into solvent as compared with individual HF and BF3. The solubility was 68wt% into benzene, 96% into THF and 99% (nearly 100%) into pyridine. It was suggested that production of Broensted acid with strong acidity causes strong catalysis. 6 refs., 2 figs., 1 tab.

  15. Development of inspection system for vehicle interior transient noise using non-stationary signal analysis; Hiteijo shingo bunseki wo mochiita sharyo ion hantei system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, H; Ueda, K [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    A method to inspect the rattle, one of the transient noises of car interior, is developed. In the method, the waveform data of overall noise are analyzed using Wigner distribution, and its rattle component is condensed and separated from the background excitation noise. Then the rattle component is classified into three levels: strong, middle and none, using the neural network. A fuzzy inference is also used to select regular waveform measurements. Experimental results show that the correct classification ratio of the method is more than 90%, which equals skilled inspection operators in accuracy. 11 refs., 8 figs.

  16. ISC feedforward control of gasoline engine. Adaptive system using neural network; Jidoshayo gasoline engine no ISC feedforward seigyo. Neural network wo mochiita tekioka

    Energy Technology Data Exchange (ETDEWEB)

    Kinugawa, N; Morita, S; Takiyama, T [Osaka City University, Osaka (Japan)

    1997-10-01

    For fuel economy and a good driver`s feeling, it is necessary for idle-speed to keep at a constant low speed. But keeping low speed has danger of engine stall when the engine torque is disturbed by the alternator, and so on. In this paper, adaptive feedforward idle-speed control system against electrical loads was investigated. This system was based on the reversed tansfer functions of the object system, and a neural network was used to adapt this system for aging. Then, this neural network was also used for creating feedforward table map. Good experimental results were obtained. 2 refs., 11 figs.

  17. Investigation of the simulation for the solar DHW system by TRNSYS; TRNSYS ni yoru kaihogata tank wo mochiita solar kyuto system no simulation chosa

    Energy Technology Data Exchange (ETDEWEB)

    Oishi, M; Noguchi, T [Japan Quality Assurance Organization, Tokyo (Japan); Okumiya, M [Nagoya University, Nagoya (Japan)

    1997-11-25

    With an objective of establishing a method for evaluating performance of a photovoltaic hot water supply system, a discussion was given on utilization of the simulation program, TRANSYS. The discussion was addressed on a photovoltaic hot water supply system of forcible circulation type using commercially available open-type heat storage tanks. An experiment was performed as an indoor test using an artificial solar light source. The TRANSYS makes available a type 04 which handles each node as a complete mixture by fixing and dividing the heat storage tank, and a type 38 which expresses heat transfer between temperature layers by means of piston flow as a heat transfer coefficient. Both types were subjected to calculation. The result of the discussion may be summarized as follows: both types provided values close to the experimental values of quantity of heat derived by utilizing solar heat; however, with the type 04, heat transfer cannot be modeled if the system is left still with temperature difference in the heat storage tank being large; and with the type 38, modeling is possible when the system is left still with temperature difference in the heat storage tank being large, but temperature gradient is difficult to be modeled during heat collection and when hot water is supplied. 1 ref., 7 figs., 5 tabs.

  18. Simulation model of a solar collector with a heat capacitance on TRNSYS; TRNSYS wo mochiita netsuyoryo wo motsu heibangata shunetsuki no model ka

    Energy Technology Data Exchange (ETDEWEB)

    Yoshinaga, M [Nagoya City University, Nagoya (Japan); Okumiya, M [Nagoya University, Nagoya (Japan)

    1997-11-25

    A flat plate type heat collector considering a heat capacitance was structured; assembled into a solar system simulation program, TRNSYS; correction was made on this model for permeation and absorption rates as a result of incident angles onto the heat collecting surface on which sunlight reaches directly; and effectiveness of the proposed model was verified from comparing the heat collection amount with that of conventional systems and measured values. The heat collection amount decreased when incident angles of insolation are taken into consideration, and the amount approached the measured value in the case of the system with a heat capacitance. Variation in temperature at the heat collector exit decreased when the heat capacitance was taken into account. With the case of having no heat capacitance, heat collecting amount greater than the actually collected amount was calculated for days with great insolation, and less amount was calculate for smaller insolation. However, the value as a whole has become close to the measured value, though slightly greater. A value still closer to the measurements was obtained when the incident angle is considered. As seen in a seven-day average, a model having no heat capacitance and not considering the incident angle had an error from the measured value of 38.6%, while a model having a heat capacitance and considering the incident angle had an error of 9.9%. 5 refs., 7 figs.

  19. Investigation on chemical heat pump using calcium-chloride; Enka calcium no suiwa dassui hanno wo mochiita solar chemical heat pump ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, I; Arai, T; Saito, Y [Meiji University, Tokyo (Japan)

    1997-11-25

    With an objective of developing a room heating system utilizing a solar chemical heat pump, an experimental system was fabricated to evaluate its performance. Steam was employed as a working gas, and for a reaction material, calcium-chloride was used, which has a reaction temperature zone permitting safe use and fitting the purpose among other hydrate systems and has high standard enthalpy in hydration. Water was used as a solar heat transferring medium. The system operates under the following principle: a container I is filled with hydrated salt and a container II with water, the two containers being linked with a pipe interposed with a valve; heat is inputted and outputted by performing charging and discharging alternately; and the role of a heat pump is played by deriving from environment the heat of water evaporation in the container II during discharging. The COP must take into account the electric power consumption of the water circulation pump to transfer solar heat. A COP of 0.256 was derived as a result of the experiment. 3 refs., 5 figs.

  20. Three-dimensional mise-a-la-masse modeling using horizontal well; Suihei kosei wo mochiita ryuden den`iho no sanjigen modeling

    Energy Technology Data Exchange (ETDEWEB)

    Mizunaga, H; Ushijima, K; Hashimoto, K; Masuda, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-10-01

    The 3-D model program was developed to apply a mise-a-la-masse method to linear current sources with optional shapes. Mise-a-la-masse method is a bipolar mapping survey method using current sources installed in wells, and recently has been widely used for direct exploration of geothermal reservoirs. This method is also used for monitoring underground fluid as electrode arrangement of fluid flow tomography for surveying underground fluid (geothermal fluid, underground water, petroleum). In the geothermal reservoir exploration, the casing pipes of wells are used as linear current sources, and measured data are processed as those based on vertical current source. In the largely inclined well, the inclination of current sources should be considered. The 3-D modeling program was developed by difference calculus using the theoretical potential equation and apparent resistivity based on linear current sources with optional 3-D shapes. The numerical model experiment result clarified that the previous theoretical equation for vertical wells is inapplicable to inclined linear current sources because of clear asymmetric apparent resistivity distribution. 6 refs., 6 figs.

  1. Optimization of the ship type using waveform by means of Rankine source method; Rankine source ho ni yoru hakei wo mochiita funagata saitekika ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Hirayama, A; Eguchi, T [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)

    1996-04-10

    Among the numerical calculation methods for steady-state wave-making problems, the panel shift Rankine source (PSRS) method has the advantages of rather precise determination of wave pattern of practical ship types, and short calculation period. The wave pattern around the hull was calculated by means of the PSRS method. The waveform analysis was carried out for the wave, to obtain an amplitude function of the original ship type. Based on the amplitude function, a ship type improvement method aiming at the optimization of ship type was provided using a conditional calculus of variation. A Series 60 (Cb=0.6) ship type was selected for the ship type improvement, to apply this technique. It was suggested that optimum design can be made for reducing the wave making resistance by means of this method. For the improvement of Series 60 ship type using this method, a great degree of reduction in the wave making resistance was recognized from the results of numerical waveform analysis. It was suggested that the ship type improvement aiming at the reduction of wave-making resistance can be made in shorter period and by smaller labor compared with the method using a waveform analysis of cistern tests. 5 refs., 9 figs.

  2. Study of 1D complex resistivity inversion using digital linear filter technique; Linear filter ho wo mochiita fukusohi teiko no gyakukaisekiho no kento

    Energy Technology Data Exchange (ETDEWEB)

    Sakurai, K; Shima, H [OYO Corp., Tokyo (Japan)

    1996-10-01

    This paper proposes a modeling method of one-dimensional complex resistivity using linear filter technique which has been extended to the complex resistivity. In addition, a numerical test of inversion was conducted using the monitoring results, to discuss the measured frequency band. Linear filter technique is a method by which theoretical potential can be calculated for stratified structures, and it is widely used for the one-dimensional analysis of dc electrical exploration. The modeling can be carried out only using values of complex resistivity without using values of potential. In this study, a bipolar method was employed as a configuration of electrodes. The numerical test of one-dimensional complex resistivity inversion was conducted using the formulated modeling. A three-layered structure model was used as a numerical model. A multi-layer structure with a thickness of 5 m was analyzed on the basis of apparent complex resistivity calculated from the model. From the results of numerical test, it was found that both the chargeability and the time constant agreed well with those of the original model. A trade-off was observed between the chargeability and the time constant at the stage of convergence. 3 refs., 9 figs., 1 tab.

  3. Destratification efficiency by hypolimnitic water lifter with air bullets. Kihodan wo mochiita shinsosui yosui shisetsu ni yoru mitsudo seiso no kongo koritsu

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, H; Suga, K [Utsunomiya University, Tochigi (Japan). Faculty of Engineering; Asaeda, T [Saitama University, Saitama (Japan). Faculty of Engineering

    1994-02-21

    The intermittent aeration and circulation method is used frequently to destruct temperature stratification in a reservoir to prevent it from eutrophication. This method uses a cylinder erected in water, into which air bullets are shot out intermittently to circulate and mix heavier water mass upward. The present study has performed numerical analysis on the process to mix density stratifications by operating an intermittent water lifter cylinder for an extended period of time, and discussed responses of each factor to variation. The numerical computation has been carried out according to the equation of motion for water and air in the water lifter cylinder, and the numerical model that hypothesizes the double plume after air bubbles have departed from the water lifter cylinder. The result indicated that the amount of hypolimnitic water lifted against the amount of air injected can be expressed by an empirical formula that uses only the relative air bullet volumes. An evaluation formula for the water lifting efficiency has also been derived. It has been found for the stratification mixing that trends in the mixing efficiency can be identified by two parameters of dimensionless air bubble amount and stratification strength. 17 refs., 11 figs., 4 tabs.

  4. High resolution seismic refraction method with multichannel digital data acquisition system; Digital ta channel sokutei system wo mochiita koseido kussetsuho jishin tansa

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, K [Oyo Corp., Tokyo (Japan)

    1997-05-27

    This paper introduces a multichannel digital data acquisition system and examples of measurements with the system in seismic exploration using the high resolution seismic refraction method. The high resolution seismic refraction system performs analyses nearly automatically by using a computer after initial travel time has been read. Therefore, the system requires high-accuracy travel time data, for which a multichannel digital measuring instrument developed recently for seismic exploration using the refraction method has been used for the measurement. The specification specifies the number of channels at 144 as a maximum, a sampling time of 62.5 {mu}sec to 4 m sec, the maximum number of sampling of 80,000 samples, and gain accuracy of {plus_minus} 1%. The system was used for surveying a tunnel having a maximum soil cover of about 800 m. The traverse line length is about 6 km, the distance between vibration receiving points is 50 m, and the number of vibration receiving points is 194. Executing measurements of single point system using GPS can derive accurate velocity in the vicinity of the basic face of the tunnel construction. Results were obtained from the investigation, which can serve more for actual construction work. 10 refs., 6 figs., 1 tab.

  5. Laboratory study on streaming potential for exploring underground water flow; Shitsunai jikken ni yoru ryudo den`i wo mochiita mizu michi tansa no kanosei no kento

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H; Shima, H [Oyo Corp., Tokyo (Japan)

    1997-05-27

    To investigate a possibility of exploration of underground water flow as well as to grasp the underground fluid flow by measuring streaming potential at the ground surface, some experiments were conducted using a model unit by considering the difference of permeability. For this experimental unit, water is driven by adding head difference between the polyethylene vessel filled with water and the experimental water tank. The size of water tank is 350{times}160 mm with a height of 160 mm. Twenty platinum electrodes are set on the cover of water tank. Toyoura standard sand and Kanto loam were used for the experiments. For the experiments, fluid was injected in various combined models by considering the permeability, to measure the streaming potential. As a result, it was explained by the streaming potential that the fluid flows in a form of laminar flow in the experimental water tank, and that the movement of fluid in the Kanto loam is quite slow. It was also confirmed that the streaming potential method is an effective technique for grasping the movement of fluid. 3 refs., 8 figs.

  6. Simulation study using 3-D wavefield modeling for oil and gas exploration; Sanjigen hadoba modeling wo mochiita sekiyu tanko no simulation study

    Energy Technology Data Exchange (ETDEWEB)

    Sato, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Saeki, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    As the surroundings of objects of oil exploration grow more complicated, seismic survey methods have turned 3-dimensional and, in this report, several models are examined using the 3-dimensional simulation technology. The result obtained by the conventional wave tracking method is different from actual wavefields, and is unrealistic. The difference method among the fullwave modelling methods demands an exorbitantly long computation time and high cost. A pseudospectral method has been developed which is superior to the difference method, and has been put to practical use thanks to the advent of parallel computers. It is found that a 3-dimensional survey is mandatory in describing faults. After examining the SEG/EAGE Salt model, it is learned that the salt is well-developed and that 3-dimensional depth migration is required for sub-salt exploration. It is also found through simulation of the EAGE/S Overthrust model, which is an elastic model, that no quality records are available on thrust zones in complicated terrains. The records are poor in quality since the actually measured wavefield is regarded as an acoustic wavefield when it is an elastic wavefield. 1 refs., 18 figs., 2 tabs.

  7. Static shift correction of MT data in Tohoku district using TEM soundings; TEM ho data wo mochiita Tohoku chiho MT ho data no statistic shift hosei

    Energy Technology Data Exchange (ETDEWEB)

    Kawakami, N; Kumekawa, Y; Miura, Y; Takasugi, S [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Fujinawa, Y [National Research Institute for Disaster Prevention, Tsukuba (Japan)

    1997-05-27

    There is a possibility that the wide-band MT observation data obtained in the central part of Tohoku district include the static shift effect. To grasp the static shift effect in the MT data, the TEM soundings were conducted at all the site where the MT data were measured. The TEM sounding system was developed for the shallow survey depth ranging from 5 m to 150 m. When showing the measured results on the histogram, it was found that the static shifts were concentrated in the vicinity of zero. About 70% of the data was below 0.2 decade. Only a slight static shift effect was observed. This means that the results obtained by the two-dimensional analysis are plausible. Especially, the static shift around plain was small. Therefore, the current results around the plain were trustful. On the other hand, the static shift in the mountainous area was rather large. Accordingly, the results around the mountainous area should be carefully treated. 7 refs., 10 figs.

  8. Fundamental study of interpretation technique for 3-D magnetotelluric data using neural networks; Neural network wo mochiita sanjigen MT ho data kaishaku gijutsu no kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, T; Fukuoka, K; Shima, H [Oyo Corp., Tokyo (Japan); Mogi, T [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Spichak, V

    1997-05-27

    The research and development have been conducted to apply neural networks to interpretation technique for 3-D MT data. In this study, a data base of various data was made from the numerical modeling of 3-D fault model, and the data base management system was constructed. In addition, an unsupervised neural network for treating noise and a supervised neural network for estimating fault parameters such as dip, strike and specific resistance were made, and a basic neural network system was constructed. As a result of the application to the various data, basically sufficient performance for estimating the fault parameters was confirmed. Thus, the optimum MT data for this system were selected. In future, it is necessary to investigate the optimum model and the number of models for learning these neural networks. 3 refs., 5 figs., 2 tabs.

  9. Nodal head method with matric operation in analysis of mine ventilation networks. Matrics kaiho wo mochiita setten ho ni yoru tsuki mo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, K.; Miyakoshi, H. (Akita Univ., Akita (Japan). Mining College); Kinoshita, H.; Onozuka, T. (Hanaoka Mining Co. Ltd., Akita (Japan))

    1990-09-25

    In this report, the method of analyzing mine ventilation networks is explained in which the direct matric operation method is applied to the solution of the linear equation system introduced from the fundamental equation of the nodal head method. In other words, the fundamental equation was expressed by genelarized equation composition by using connecting functions between nodes and the algorism of a computer program was clarified. And the calculation method necessary for other ventilation netwrks analysis was shown in a concrete form. For solving the linear equation system, the matric operation method based on the modified Choleski's method was used in order to speed up the calculation and stabilize the convergence process of the solution. As examples, calculation was made on the ventilation networks of total numbers of the nodes of 8, 14, 51 and 141. From these ventilation network analyses, using a linear equation system concerning the nodal pressure correction, it was found that in the system with convergence acceleration coefficient of 1.4, the number of sequential repeating frequency of approximation Mc which was required for convergence was in the order of Mc {approx equal} 13 (cycle) for the condition that the fan pressure was constant and the convergence condition was {vert bar} AQi {vert bar}{sub max} {lt} 0.1m {sup 3}/min. 14 refs., 12 figs., 3 tabs.

  10. Method for evaluating environmental performance of technologies by using the interindustry relations table; Sangyo renkanhyo wo mochiita gijutsu no kankyosei hyoka shuho

    Energy Technology Data Exchange (ETDEWEB)

    Hondo, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-01-30

    This paper describes a proposal of a method for evaluating environmental performance of technologies by using the interindustry relations table, and the case studies thereof. This method is characterized in that it can evaluate two effects affecting the environment: structuring of capital facilities required in association with introduction of the technologies and the changes in social structures. As a parameter to compare the technologies considering these effects, a concept of life cycle limited emission amount was introduced. In the case studies, life cycle limited CO2 emission amounts from using seven kinds of technologies were calculated, and environmental performances of each technology were compared. The result indicated that introduction in Japan of coal, oil and LNG fired thermal power generation will increase CO2 emission amount from the whole society. Conversely, introduction of hydraulic, nuclear, photovoltaic, and wind power generation technologies will reduce the CO2 emission amount. It is pointed out particularly that hydraulic and nuclear power generation can minimize CO2 emission from structuring capital facilities, and is an excellent technology from a viewpoint of reducing CO2 emission from the society as a whole. 5 refs., 6 figs., 1 tab.

  11. Construction of educational application system for calligraphy master based on virtual reality; Virtual reality wo mochiita shodo shutoku no tame no kyoikuteki oyo system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, T.; Muranaka, N.; Imanishi, S. [Kansai University, Osaka (Japan)

    1997-10-20

    Technique of virtual reality has been becoming popular in various fields including education because of its remarkable technique progress. There are the three useful elements of `presence`, `interaction` and `autonomy` in realizing the virtual reality. Here, we are focusing on the `presence` in constructing a simple supporting system for calligraphy education. We take advantage of the virtual image with reality to use as an educational interface because the virtual image and the real image are overlapped by showing the visual scene in the system. It is general that the unity of the virtual image and the real image has been processed as the stationary pictures by using `See-through HMD` and so on. In this paper, by using half mirror in stead of using the HMD with restraint, we are released from its restrainable sense. The virtual image and the real image are laid to overlap as the mobile pictures. The virtual hand replays the character inputted on the tablet by the excellent calligrapher. A calligraphic trainee is practicing overlapping the virtual hand which is reflected at the half mirror, while the trainee is doing the character on the tablet in the handwriting. The trainee is repeatedly practicing with feedback and is getting better in handwriting the character. It is shown in the good expermental results that the system has a proven effectiveness. 9 refs., 12 figs., 2 tabs.

  12. Improvement of combustion in a direct injection diesel engine by micro-hole nozzle; Micro hole nozzle wo mochiita chokusetsu funshashiki diesel kikan no nensho kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Murata, M. [Keio University, Tokyo (Japan); Kobori, S. [Tokyo Institute of Technology, Tokyo (Japan); Iida, N. [Keio University, Tokyo (Japan). Faculty of Science and Technology

    2000-07-25

    In an attempt to promote the atomization of fuel spray and the mixing of fuel and air in diesel engines, a micro-hole nozzle which has orifices with a diameter smaller than 0.10mm was developed. In this study, the combustion tests were carried out using a single cylinder diesel engine equipped with a micro-hole nozzle and a common rail type high-pressure fuel injection system. A comparison with the results of a conventional nozzle experiment showed that the peak of initial premixed combustion increased, but the peak of diffusion combustion decreased. As a result, when nozzle orifice diameter become small from {phi} 0.15 mm to {phi} 0.10 mm, the combustion was accompanied by smokeless with the same levels of NO{sub x} emission and fuel economy. And results of a comparison the toroidal type chamber with the shallow dish type chamber revealed that the optimization of combustion chamber is necessary for the increase of the injection stage with increasing of the number of nozzle orifice. If an orifice diameter becomes {phi} 0.06 mm, the diffusion combustion can not be observed and the combustion is formed of only premixed combustion. The combustion in the case of {phi} 0.06 mm was accompanied with the drastic deterioration of fuel economy, smoke and HC with all over load. But the micro-hole nozzle has a potential for the formation of the lean and homogeneous premixed mixture until the fuel-air mixture ignites. (author)

  13. Improvement of prediction accuracy of large eddy simulation on colocated grids; Colocation koshi wo mochiita LES no keisan seido kaizen ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Inagaki, M.; Abe, K. [Toyota Central Research and Development Labs., Inc., Aichi (Japan)

    1998-07-25

    With the recent advances in computers, large eddy simulation (LES) has become applicable to engineering prediction. However, most cases of the engineering applications need to use the nonorthgonal curvilimear coordinate systems. The staggered grids, usually used in LES in the orthgonal coordinates, don`t keep conservative properties in the nonorthgonal curvilinear coordinates. On the other hand, the colocated grids can be applied in the nonorthgonal curvilinear coordinates without losing its conservative properties, although its prediction accuracy isn`t so high as the staggered grid`s in the orthgonal coordinates especially with the coarse grids. In this research, the discretization method of the colocated grids is modified to improve its prediction accuracy. Plane channel flows are simulated on four grids of different resolution using the modified colocated grids and the original colocated grids. The results show that the modified colocated grids have higher accuracy than the original colocated grids. 17 refs., 13 figs., 1 tab.

  14. Indirect solar-pumped laser diode using a solar cell; Taiyo denchi wo mochiita taiyoko kansetsu reikigata handotai laser no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kanamori, Y.; Yugami, H.; Naito, H.; Arashi, H. [Tohoku University, Sendai (Japan). Faculty of Engineering

    1996-10-27

    This paper describes the operating characteristics of a stabilizing circuit using commercial electricity, those of a stabilizing circuit using solar cells, relation between the quantity of solar radiation and the maximum output of a semiconductor laser diode (LD), and simulation results of annual LD output in Sendai City. The stabilizing circuit for the solar-cell driven LD was structured such that the output of the solar cell panels was guided to a DC/DC converter, that the voltage was set at a prescribed value and that the current was stabilized with the use of power MOSFET. The solar cells used in the experiment were monocrystal silicone solar cells with the maximum output of 53W each. In the experiment, the LD was protected by stabilizing the current at a set value when an excess current was supplied to the stabilizing circuit. As a result of the simulation of the annual LD output from the meteorological data of Sendai City, it was predicted that a solar cell of approximately 1kW was able to provide an annual output of 102MJ and that the efficiency was highest with four sheets of the solar cell. Consequently, consistency proved to be essential between the LD and the solar cell output. 3 refs., 7 figs.

  15. Oxygen sensor using proton-conductor thick-film operative at room temperature. Puroton dodentai atsumaku wo mochiita joon sadogata sanso sensor

    Energy Technology Data Exchange (ETDEWEB)

    Miura, Norio; Yoshida, Nobuaki; Matayoshi, Naoko; Shimizu, Yoichi; Yamazoe, Noboru; Kuwata, Shigeki [Kyushu Univ., Fukuoka, (Japan) Niihama National College of Tech., Ehime, (Japan)

    1989-10-01

    An amperometric solid-state oxygen sensor using a proton-conductor thick-film was examined as a miniaturized and intelligent oxygen sensor operative at room temperature. The good-conditioned proton-conductor film of about 10{mu}m in thickness without holes was formed on a porous alumina substrate by spin-coating the paste containing antimonic acid and a polyvinyl alcohol binder. Using this material, the thick-film oxygen sensor was made. A limiting current, controlled by oxygen permeation through the gas-diffusion layer, was observed when an external voltage was over 1.4V. The limiting current increased linearly with an increase in oxygen partial pressure up to 1.0 atm at an external voltage of 1.6V. The 90% response time for increasing oxygen partial pressure was about 40 seconds at 30 centigrade. Moreover, it was found that the sensor could also respond to dissolved oxygen in water at room temperature. With a sensor using a hydrophobic gas-diffusion layer containing a polystyrene binder, the limiting current was linear to the dissolved oxygen concentration up to 20ppm. 15 refs., 5 figs.

  16. Analogue experiment of the crustal deformation by X-ray CT; X sen CT wo mochiita chikaku no henkei no analogue jikken

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, Y.; Shi, B; Murakami, Y. [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    This paper reports a predictive result on a deformation experiment on sand beds using an X-ray computerized tomography (CT) equipment. The X-ray CT is a method to perform the following processes: X-rays are irradiated on a sample; decayed intensity data are measured along ray paths of the permeated X-rays; the data are inverted by using the Fourier transform; and spatial distribution of the coefficient of X-ray absorption inside the sample is acquired as a gray scale image. The deformation experiment was carried by putting sand into an acrylic container to a depth of 2 cm and manually pressing a plate in the horizontal direction. Sand blocks make a relative motion along a specific plane when they are deformed, but it was not possible to recognize faults clearly by naked eyes. Upon completion of the deformation, the experimental device was placed on the CT equipment to acquire images of the two-dimensional cross section. The higher the X-ray absorption coefficient, the brighter the picture elements. It can be seen that three inversed faults have been imaged clearly. Therefore, this equipment was verified usable as an effective observation equipment for an analogue deformation experiment. 4 refs., 2 figs.

  17. Development of new finite element by source method. 2nd Report. Plate bending element; Source wo mochiita atarashii yugen yoso no kaihatsu. 2. Itamage yoso

    Energy Technology Data Exchange (ETDEWEB)

    Neki, I.; Tada, T. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1996-12-31

    This paper reports a method to develop a new finite element by source (FES) for a two-dimensional plane problem and a three-dimensional solid problem as a method to analyze ship body structures. The paper describes development of a plate bending element by using a similar method, and the fundamental principle thereof. The present method can prepare a finite element of an arbitrary shape by simply providing a contact point only on a boundary. It can also derive good calculation accuracy with less number of contact points and elements. These facts are shown by examples of analyses on a square plate, a triangle plate and a semi-circular plate. Particularly, since a plate bending problem has a large order of differential calculus in a governing equation, this method being a semi-analytical method derives a result with very good accuracy even with less number of contact points. A hypothetical boundary method or a hypothetical electric charge method presents not a very high accuracy even if a large number of contact points are provided. This is because the method hypothesizes only a bending moment vertical to the boundary, but does not consider a source of the moment relative to the boundary. In contrast, the present method hypothesizes both of bending and twisting as the sources, hence its accuracy is better than with the above two methods. 5 refs., 11 figs., 7 tabs.

  18. Co-generation system with a linear concentrator and thermoelectric elements; Senkei shukokei to netsuden henkan soshi wo mochiita netsuden heikyu system

    Energy Technology Data Exchange (ETDEWEB)

    Kachi, E; Suzuki, A; Fujibayashi, K [Tokyo University of Agriculture and Technology, Tokyo (Japan)

    1996-10-27

    The co-generation system using a solar cell has the disadvantage that the performance of a cell element deteriorates when the temperature rises. Therefore, the co-generation system in which a BiTe thermoelectric element and linear Fresnel lens are used was constructed. Moreover, the basic characteristics were confirmed and the characteristics of a system model were analyzed. A thermoelectric element area must be reduced to improve the generating efficiency. The generating efficiency depends on the temperature difference between thermoelectric elements rather than the thermoelectric element area. As the thermoelectric area gets lower, the generating efficiency will get higher. This inclination is advantageous on the economic side. The generating efficiency becomes low during operation at high temperature. As a result, the temperature supplied to the thermal load is set to the lower position (100 to 200{degree}C) so as to advance the validity of the system. Even if the co-generation temperature is low, a heat supply capability of 150{degree}C is sufficient for an industrial heat supply system because it holds a large majority of the consumption demand for the whole industry. 3 refs., 8 figs., 3 tabs.

  19. Silent cooling system with a double suction type centrifugal fan with backward blades; Ryosuikomi turbo fan wo mochiita teisoon engine reikyaku system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Funabashi, S. [Hitachi, Ltd., Tokyo (Japan); Nakamura, K. [Hitachi Construction Machinery Co. Ltd., Tokyo (Japan)

    2000-04-25

    We have developed a new cooling system for the engine of construction machinery. This system produces two different air flow routes by a double suction type centrifugal fan with backward blades. We first measured aerodynamic performance and sound level of the double suction type fan, which consists of two single suction type fans of different design, and compared these measurements to those of single suction type fans. Next, we installed the fan in a scale model of the new cooling system. The performance of this double suction type fan was different to that of a single suction type. It is considered that the effect of interaction of the exit flows from the two different fans caused this performance change. The test model installed in an engine compartment showed that this cooling system reduced the area of air inlets and outlets around the engine and did not cause re-circulation of cooling air. (author)

  20. Study of shift shock reduction of an automatic transmission using robust control; Robust seigyo wo mochiita ido hensokuki no hensoku shock teigen ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Oshima, K [JATCO Corp., Shizuoka (Japan); Totsuka, H; Sanada, K; Kitagawa, A [Tokyo Institute of Technology, Tokyo (Japan)

    1997-10-01

    To effectively reduce shift shock of an Automatic Transmission, we designed a feed-back controller that manipulates the hydraulic pressure of a clutch and input torque, and also controls the turbine revolution and output torque. We used robust control theory to consider the fluctuation of hydraulic characteristics and friction elements, and verified the effect of the controller by simulation and experiment. 1 ref., 11 figs.

  1. Evaluation of indoor thermal environment with improved 65 nodes thermoreguration model; Kairyogata 65 bunkatsu taion chosetsu model wo mochiita shashitsunai onnetsu kankyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Matsunaga, K; Sudo, F [Isuzu Motors Ltd., Tokyo (Japan); Tanabe, S [Ochanomizu Univ., Tokyo (Japan)

    1997-10-01

    Indoor thermal environment of a vehicle was evaluated by a numerical simulation. A numerical simulation using the equivalent temperature measured with the thermal manikin was conducted. Numerical manikin was improved and convective and radiative heat transfer at each body surface was described in detail. Comparative examination using the calculation results by the numerical simulation was also conducted. 3 refs., 8 figs., 2 tabs.

  2. 3D-image theater system using TLP770J LCD data projector; Ekisho data projector wo mochiita rittai eizo theater system

    Energy Technology Data Exchange (ETDEWEB)

    Kawasato, H. [Toshiba Corp., Tokyo (Japan)

    2000-02-01

    In today's multimedia era, visual systems are widely used not only for two-dimensional images but also for the depiction of virtual reality and for simulated three-dimensional images. At the same time, the projection technology used in large-screen projectors is shifting from the cathode ray tube (CRT) to the liquid crystal display (LCD). Toshiba has developed a simplified 3D-image theater system using the TLP770J LCD data projector, which offers easy maintenance and lower costs. (author)

  3. Construction of taste-odor recognitition system using optimized sensory device; Kankaku tekio sensa wo mochiita aji/nioi shikibetsu sisutemu no kosei

    Energy Technology Data Exchange (ETDEWEB)

    Osada, H.; Yoshida, H.; Omamiuda, Y.; Ajishi, Y.; Seki, K. [Iwate University, Iwate (Japan); Kikuchi, S. [Tohoku Gakuin University, Miyagi (Japan)

    1997-06-20

    Until now, the quality of foods, that is, as the electrical measuring method of taste and odor, the utilizing method of artificial fatty films and ceramics of ZnO and so on are devised and put to practical use. However, the field of measuring of taste and odor is a comparative new field, and it is still developing stage in the lasting quality and so on. To measure the quality of foods holds an important position in the safety management, together with supporting the development of products as the needs of user. Authors studied a new taste/odor sensor utilizing the optimized sensory device (OSD) which is prepared from sintering the mixture of the magnetic semiconductor powder such as Mn-An ferrite and ruthenium compound. When various taste and odor components included in food adheres to the OSD, resistance or electromotive force faced on surface electric conduction of the OSD change, therefore it can be clearly discriminated the sort and quality of foods. This paper describes preparation of a thick-film OSD and construction of the multi-channel taste/odor recognition system for some drinks. 12 refs., 13 figs.

  4. Optical fiber taste sensors using potential sensitive dye coatings. Makuden'i kanjusei shikisomaku wo mochiita hikari fiber mikaku sensor

    Energy Technology Data Exchange (ETDEWEB)

    Yamakawa, S.; Yamaguchi, A. (Toyama National College of Maritime Technology, Toyama (Japan))

    1992-12-20

    The present paper proposes a new taste recognition system using optical response patterns from multi-channel optical fiber sensors having potential sensitive dye coatings. It was found that the sensors give large changes in optical absorption spectra of the dyes when they are immersed in various taste solutions. Consequently, it was shown that the sensors can be used as a taste sensor. Six dyes, which give large changes in dye absorption, were selected from twenty dyes and used for six-channel optical fiber taste sensors array. The absorption spectra change data were processed by multiple discriminant analysis and neural networks using back-propagation algorithm. From the analytical results, it was demonstrated that salty (NaCl), bitter (quinidine), sweet (sucrose), sour (HCl), and umami (sodium glutamate) substances can be recognized from each other by using the optical taste sensor system. 11 refs., 8 figs., 2 tabs.

  5. Proposal and study of a long-span composite cable-stayed bridge with new hybrid girder; Atarashii gosei kozo shuketa wo mochiita chodai fukugo shachokyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, K.; Hishiki, Y.; Furuichi, K. [Kajima Corp., Tokyo (Japan)

    1999-09-30

    A hybrid or mixed structure (composite structures) are a matter of increasing concern which takes in each advantage of steel and concrete. A field of bridges is no exception, with the plan and construction carried out for the new type of composite bridge, such as a composite cable-stayed bridge and a composite extra dose bridge as a long span bridge, and a composite truss bridge and a corrugated steel plate web bridge as a medium-span bridge, with technological development becoming active in this field. In such a technological trend, a hybrid two-girder structure was devised, a structure consisting of a concrete filled steel pipe for a girder and a precast (PC) floor plate for a floor board, as the girder structure of a long-span cable-stayed bridge in the subject research; also, applicability was examined using, as an example, the composite cable-stayed bridge with hybrid girders employed for the span. This paper reports the result of the analysis of the entire system, the analysis made for the purpose of examining the characteristic and the feasibility of this hybrid girder. The analysis revealed the structural feasibility of the long-span composite cable-stayed bridge using two hybrid girders of concrete-filled steel pipes thus devised. (NEDO)

  6. Development of new finite element by source method. 2nd Report. Plate bending element; Source wo mochiita atarashii yugen yoso no kaihatsu. 2. Itamage yoso

    Energy Technology Data Exchange (ETDEWEB)

    Neki, I; Tada, T [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1997-12-31

    This paper reports a method to develop a new finite element by source (FES) for a two-dimensional plane problem and a three-dimensional solid problem as a method to analyze ship body structures. The paper describes development of a plate bending element by using a similar method, and the fundamental principle thereof. The present method can prepare a finite element of an arbitrary shape by simply providing a contact point only on a boundary. It can also derive good calculation accuracy with less number of contact points and elements. These facts are shown by examples of analyses on a square plate, a triangle plate and a semi-circular plate. Particularly, since a plate bending problem has a large order of differential calculus in a governing equation, this method being a semi-analytical method derives a result with very good accuracy even with less number of contact points. A hypothetical boundary method or a hypothetical electric charge method presents not a very high accuracy even if a large number of contact points are provided. This is because the method hypothesizes only a bending moment vertical to the boundary, but does not consider a source of the moment relative to the boundary. In contrast, the present method hypothesizes both of bending and twisting as the sources, hence its accuracy is better than with the above two methods. 5 refs., 11 figs., 7 tabs.

  7. Viljandis tuleb imeline kohtumine / Linda Järve

    Index Scriptorium Estoniae

    Järve, Linda, 1946-

    2001-01-01

    8.-22. juulinì01 toimub Eestis 10. Euroopa Laste Teatrikohtumine (EDERED - European Drama Encounter), mis toob kohale 180 last koos juhendajatega 18 riigist. Samal ajal on koos ka EDERED-i peaassamblee. Kahenädalase, peamiselt Viljandis aset leidva kohtumise korraldavad Eesti Harrastusteatrite Liit, haridusministeerium ja Viljandi linnavalitsus. EDERED loodi 1985. a, pärast 4 aastat varem toimunud esimest laste teatrikohtumist, kus osalesid 12-14-aastased lapsed. Hiljem lisandusid EDERED-i ürituste hulka ka noorte teatrikohtumised, kus osalejad on 16-20-aastased. EDERED-i kohtumistel kasutatakse mitmesuguseid teatriõpetuse meetodeid, toimub loov koostöö laste ja õpetajate vahel

  8. Study of signal transduction mechanism of angiotensin 2 receptor by means of site-directed mutagenesis; Bui totsuzen hen'iho wo mochiita anjiotenshin 2 reseputa no joho dentatsu kiko no kaimei

    Energy Technology Data Exchange (ETDEWEB)

    Yamano, Yoshiaki [Tottori University, Tottori (Japan). Faculty of Agriculture

    1998-12-16

    The renin-angiotensin system (RAS) plays an important role in the regulation of blood pressure. In order to clarify the signaling mechanism mediated by angiotensin 2 receptor, Gq-protein binding amino acid residues of this receptor were clarified by site-directed mutagenesis study. Amino acid residues in the carboxyl tail region were changed by alanines, individually. These mutated receptors were expressed stably in CHO cells, and GTP effect and second messenger molecules were determined, and three residues (Y 312, F313 and L 314) in this region were determined to be concerned for the binding of Gq protein. The other signaling systems, Gi, MAP kinase, JAK-STAT mediated, were reported to be concerned for this receptor. Novel drags for high blood pressure therapy would be explored by clarifying these signaling mechanisms. (author)

  9. Fiscal 1998 research report. Research cooperation on car energy and environmental technology based on ITS technology in China; 1998 nendo seika hokokusho. Chugoku ni okeru ITS gijutsu wo mochiita jidosha energy kankyo gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research aims at preparation of the car energy/environmental vision based on ITS (intelligent transport system) technology in China, enhancement of the transport planning ability of Qinghua University, and promotion of effective energy use in China. The following activities were carried out concretely: Survey on the actual traffic situation by Qinghua University, analysis of environment deterioration factors based on the survey result, estimation of a traffic environment improvement effect, study on traffic flow simulation technique based on traffic engineering, and study on traffic planning technique. As the diffusion strategy of ITS along Chinese circumstances, standardization and improvement of a multi- modal traffic system, navigation and its application system, and ETC (electronic toll collection) system are promising. Expectation for Japan and Japanese roles are as follows: Improvement of signal control, provision of information systems such as navigation, discussion on ITS technology such as ETC with Chinese specialists, and feasibility study on introduction of ITS technology for every Chinese district. (NEDO)

  10. Customers` response to residential peak-activated pricing. Evidence from a Japanese experiment; Peak taio ryokinka ni okeru kateiyo juyoka no fuka chosei kodo no bunseki. Kansetsu fuka seigyo jikken data wo mochiita kakaku koka no sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Asano, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-10-01

    Demand side management through a pricing mechanism, that is the indirect load control was experimented to analyze the pricing effect. When power consumption in indirect load control groups is compared between peak time band in weekdays in summer and off-the-peak time band, the power is less consumed when price gap is set than in a uniform charge time. When more number of persons is in home in daytime, room cooling is used in daytime including the peak band to adjust the demand. The substitution elasticity in price between demands in the peak time band and the off-the-peak time band is from about 0.06 to 0.07, which cannot be ignored. If the peak price is increased by four times, the demand in the peak band can be reduced by about 0.15 kW (when average power demand per household is assumed 0.75 kW). For room cooling devices, the first device is often installed in a living room and the second and further units in individual rooms such as bed rooms. The more the number of device, the higher the possibility that the use time band is outside the peak time band. This indirect load control experiment is a field test related to the peak-activated pricing for small power users, by which the users` behavior against the pricing effect was identified quantitatively. 5 refs., 1 fig., 8 tabs.

  11. Effect of deep structure and surface layer (a) simulation study on the heavy damage belt of the 1995 Hyogoken Nanbu earthquake; Hado simulation wo mochiita `shinsai no obi` ni tsuite no kento

    Energy Technology Data Exchange (ETDEWEB)

    Feng, S; Ishikawa, K; Kaji, Y [Chuokaihatsu Corp., Tokyo (Japan)

    1996-05-01

    A simulation study was done to identify the causes for the so-called heavy damage belt observed as a result of the Hyogoken Nanbu Earthquake. This study determines distributions of the maximum amplitudes on the ground surfaces, and discusses the effects of deep structures and low-velocity surface layers, based on the simulation by the wave equation with the underground model of Higashinada-ku and its vicinity in the north-south direction, observed seismic records and artificial waves. The two-dimensional scalar wave equation is used for the analysis. The velocity structure model used for the simulation is established, based on the elastic wave seismic survey results. The focus function is drawn by expanding or contracting the time scale, using the seismic records at Kobe Port Island and artificial waves. The analysis results show that the damage belt coincides with the areas at which the focusing zone of the deep structure overlap the amplification zone in the low-velocity ground surfaces, where relative density is amplified 1.5 to 2 times. It is also observed that large peaks repeat 2 to 3 times on the time scale. 5 refs., 8 figs., 1 tab.

  12. Measurements of ultrasonic waves by means of laser Doppler velocimeter and an experimental study of elastic wave propagation in inhomogeneous media; Laser doppler sokudokei ni yoru choonpa keisoku to ganseki wo mochiita fukinshitsu baishitsu no hado denpa model jikken

    Energy Technology Data Exchange (ETDEWEB)

    Nishizawa, O; Sato, T [Geological Survey of Japan, Tsukuba (Japan); Lei, X [Dia Consultants Company, Tokyo (Japan)

    1996-05-01

    In the study of seismic wave propagation, a model experimenting technique has been developed using a laser Doppler velocimeter (LDV) as the sensor. This technique, not dependent on conventional piezoelectric devices, only irradiates the specimen with laser to measure the velocity amplitude on the target surface, eliminating the need for close contact between the specimen and sensor. In the experiment, elastic penetration waves with their noise levels approximately 0.05mm/s were observed upon application of vibration of 10{sup 6}-10{sup 5}Hz. The specimen was stainless steel or rock, and waveforms caught by the LDV and piezoelectric device were compared. As the result, it was found that the LDV is a powerful tool for effectively explaining elastic wave propagation in inhomogeneous media. The piezoelectric device fails to reproduce accurately the waves to follow the initial one while the LDV detect the velocity amplitude on the specimen surface in a wide frequency range encouraging the discussion over the quantification of observed waveforms. 10 refs., 7 figs.

  13. On-site processing systems for determination of the phase velocity of Rayleigh waves in microtremors using the spatial autocorrelation method; Kukan jiko sokanho wo mochiita bidochu no Rayleigh ha iso sokudo no genba kettei system

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Umezawa, N [Saitama Institute of Environmental Pollution, Saitama (Japan)

    1996-05-01

    To render the spatial autocorrelation (SAC) method easier to use, a system has been constructed that can be used with ease on the site for the calculation of phase velocities. This system can perform two observation methods of the same frequency characteristics, that is, the simultaneous multi-point observation and one-point independent observation. The pickup is a velocity type seismograph of a natural period of 1 second that has been so electrically adjusted as to work on an apparent natural period of 7 seconds. Among the frequency characteristics, those related to phase are regarded as important because the SAC method is based on the measurement of coherence between two points. The analysis software runs on a waveform processing software DADiSP/WIN designed for personal computers. To know the operability of this system on the site and to accumulate records using the SAC method, observations were made at the depth of 100-500m at 6 locations in Saitama Prefecture where the underground structure was known thanks to prior PS logging. As the result, a dispersion curve was obtained by use of an array of appropriate dimensions at every location agreeing with the underground structure. 9 refs., 10 figs.

  14. Fundamental study on hydrogen storage with hydrogen absorbing alloys. Operating characteristics of storage tank; Suiso kyuzo gokin wo mochiita suiso chozo ni kansuru kiso kenkyu. Chozo yoki no dosa tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sekiguchi, S.; Sekiguchi, N.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Hydrogen absorption by a hydrogen storage (MH storage) is investigated for static characteristics, with a constant current applied to the hydrogen generator, and dynamic characteristics, with a fluctuating current applied to the same simulating actual insolation. In the experiment, alloy temperature (MH temperature) in the storage and a current for the generator are preset, and then automatic measurement is allowed to proceed at 10-second intervals of the differential pressure, hydrogen temperature in the piping, absolute pressure, MH temperature, room temperature, and water tank temperature. It is found as the result of the experiment that absorption performance is improved when the MH storage is cooled; that the mean absorption rate which is 1 without cooling increases to 1.62 at 7degC; that the mean absorption rate changes in proportion to the applied current (introduced hydrogen flow rate); that the rate which is 1 at 32A decreases to 0.53 that at 16A; that the absorption rate is dependent more on the current applied to the storage than the temperature of the heat exchanging medium; and that, even in the presence of fluctuation halfway in the applied current, the total absorption will be equal to a case of constant current application if the total amount of applied current is equal. 2 refs., 7 figs., 5 tabs.

  15. Seismic risk assessment of building based on damaged database of 1995 Hyogoken Nanbu Earthquake; Hyogoken nanbu jishin no hisai database wo mochiita kenchikubutsu no jishin risk hyoka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Suwa, H.; Nobata, A.; Seki, M. [Obayashi Corp., Tokyo (Japan)

    2000-01-10

    The objective of this paper is to evaluate a vulnerability function and a repair cost in terms of each structural damage level based on the damaged database of the 1995 Hyogoken Nanbu Earthquake. The seismic risk of a building in Kobe is calculated through the analytical results. As a result, the following are verified : 1. The expectation of vulnerability function, in which peak ground acceleration is taken for seismic intensity, is about 550 cm/s{sup 2} for minor damage, about 700 cm/s{sup 2} for moderate damage, and about 950 cm/s{sup 2} for major damage respectively. However, the coefficient of variation (C. O. V. ) is about 0.5 for all damage levels. 2. The expectation of repair cost per square meter is about 29000 yen for minor damage, about 60000 yen for moderate damage, and about 64000 yen for major damage respectively. However, the variation is very large, for example, the C. O. V. for repair cost varies from 1.2 to 1.6. 3. The seismic risk of a building in Kobe, that is normalized by new construction cost, is about three percent on condition that the design lifetime is assumed to be 50 years. (author)

  16. Evaluation of the autonomic neuropathy function immediately after a change to upright posture using the impulse response function; Impulse oto kansu wo mochiita shisei henkan katoki ni okeru jiritsu shinkei kino hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yokoyama, K. [Nagoya City University, Nagoya (Japan); Moyoshi, M.; Takata, K. [Daido Institute of Technology, Nagoya (Japan); Watanabe, Y. [Toyota College of Technology, Aichi (Japan)

    1997-05-20

    Autonomic neuropathy function immediately after a change to upright posture has been evaluated by applying transient response function of the system to the blood regulation system. The impulse response function was determined from the change in heart rate before postural change to the upright posture, and was compared with the transient change immediately after a change to the upright posture. The time series of R-R interval of electrocardiogram was used as the time series of the change in heart rate. To determine the impulse response function, an autoregressive model was applied to the R-R interval time series. The impulse response function at the steady state is a transient reaction at the impulse stimulation added to the blood regulation system. The R-R interval decreases rapidly by the autonomic neuropathy reaction in which the blood is rapidly transferred into the legs immediately after a change to upright posture. There is a close correlation between the initial temporary decrease in R-R interval and the impulse response function derived from the change in heart rate immediately after a change to the upright posture. Accordingly, the blood regulation and autonomic neuropathy functions can be evaluated by the impulse response function without actual standing test and load of tested persons. 9 refs., 3 figs., 1 tab.

  17. Synthesis of (E)-9-Oxo-2-decenoic acid (the queen substance of honeybee) from methyl 3-formylpropionate; 3-horumiruporopion san mechiru wo mochiita (E)-9-okiso-2-desen san (Mitsubachi joo busshitsu) no gosei

    Energy Technology Data Exchange (ETDEWEB)

    Tsukasa, H. [Toyotama Koryo Co. Ltd., Tokyo (Japan)

    1997-05-20

    The queen substance, (E)-9-oxo-2-decenoic acid (1) is a pheromone secreted by queen honeybee (Apis mellifera) and inhibits reproductive ability of worker bees. Several synthesese have been reported. It was synthesized starting from methyl-3-formylpropionate this time. Methyl 7,7-ethylenedioxy-4-oxooctanoate was prepared by radical addition reaction from (2) and 2-methyl-2-vinyl-1,3-dioxolane and reduced to an ethyelenedioxy carboxylic acid with hydrazine and KOH. This compound was converted to an alcohol by reduction with sodium bis(2-methoxyethoxy)aluminum hydride, followed by oxidation with pyridinium chlorochromate to an acetal aldehyde, which was condensed with malonic acid and (1) was obtained after the hydrolysis with hydrochloric acid. 7 refs., 1 tab.

  18. Preparation and properties of TiO2 films by complexing agent-assisted sol-gel method. Yuki haiishi wo mochiita sol gel ho ni yoru TiO2 usumaku no sakusei to seishitsu

    Energy Technology Data Exchange (ETDEWEB)

    Nishide, T [Nissan Motor Co. Ltd., Tokyo (Japan); Mizukami, F [National Chemical Laboratory for Industry, Tsukuba (Japan)

    1992-09-01

    In order to control optical properties of TiO2 thin films, the TiO2 films were prepared by the sol-gel method using glycols or their ether derivatives as organic ligands to study the effect of the organic ligands on the refractive indices and crystal phases. Samples were prepared as follows: Organic ligand was added into the ethanol solution of Ti(O-iso-pr) 4, and aqueous nitric acid solution was added after reflux, and sol obtained by subsequent reflux was applied on soda lime glass or silicon wafer substrates, which were baked at 400 to 900 centigrade. Three kinds of ligand such as 2-(2-methoxyethoxy) ethanol were used. Measured items are the film thickness, thermal characteristics, crystal phase and refractive indices of thin films. The key points are as follows: In case of TiO2 thin films on the soda lime glass substrate, the changing pattern of refractive indices by temperature changes with the kind of ligand used and further the peak strength of anatase changes with the kind of ligand used. In case of silicon wafer substrates, the peak strength of anatase and rutile changes with the kind of ligand. The refractive indices and crystal phase can be controlled by properly using the ligand. 7 refs., 11 figs.

  19. Non-contact evaluation of mechanical properties of electroplated wear resistant Ni-P layer from the velocity dispersion of laser SAW; Laser reiki Rayleigh ha no sokudo bunsan wo mochiita taimamo Ni-P mekkiso tokusei no hisesshoku hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Morikawa, Y.; Cho, H.; Takemoto, M. [Aoyama Gakuin University, Tokyo (Japan). Faculty of Science and Engineering; Nakayama, T. [Kobe Steel Ltd., Kobe (Japan)

    1996-11-01

    We developed a new laser surface acoustic wave (SAW) system and applied this to estimate the mechanical properties of the wear-resistant Ni-P layer electroplated on a stainless steel. The velocity dispersions of Rayleigh wave of the as -plated and heat-treated Ni-P layer were obtained by the one point time domain signal processing. The Ni-P layers with excellent wear resistance produced by the heated treatment higher than 725K were found to show higher Rayleigh velocities than that of the substrate steel, while the Ni-P layer with poor wear resistance showed lower velocities. Young`s moduli of the Ni-P layer, estimated so as the computed velocity dispersion agreed with the measured one, increased with the increase of wear resistance. 10 refs., 9 figs., 2 tabs.

  20. Positron lifetime measurements and positron-annihilation induced auger electron spectroscpy using slow positron beams; Teisoku yodenshi bimu wo mochiita yodenshi jumyo sokutei oyobi yodenshi shometsu reiki oje denshi bunko

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, R. [Electrotechnical Lab., Tsukuba (Japan)

    1996-02-20

    Slow positron beam with less than several eV can be controlled freely such as accelerating, throttling the beam size, shortening the pulse or making pulse with short time width and so forth. These low positron beams are applied to various measurements like Doppler broadening measurement of annihilation {gamma} rays or lifetime measurement of positron, and secondary particle measurements using positron microscope, positron electron ray diffraction, flight time method and so forth. In particular, these recent years, high intensity slow positron beams were possible using accelerators like electron linac and its application is increasing. In this report, pulse shortening method for high intensity slow positron beam, and incidence energy variable positron lifetime measurement method using this slow pulsed beam and flight time type positron-annihilation-induced auger electron spectroscopy are outlined. In future, these measurements can be possible to carry out with high resolution and also with high counting rate if higher intensity monochromatic excellent positron beam than present one is produced. 31 refs., 5 figs.

  1. Relation between front suspension layout and handling performance. Analysis depending on the Taguchi method and ADAMS; Front suspension layout to soda tokusei no kankei ni tsuite. Kiko kaiseki gengo wo mochiita hinshitsu kogaku ni yoru kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Okada, K [Daihatsu Motor Co. Ltd., Osaka (Japan)

    1997-10-01

    A variation of suspension layout gives an influence to the vehicle dynamics. Examined the suspension layout variation to make the handling performance change small. Analyzed the effect of suspension layout variation about steering response delay and gain besides the tire wear effect and movable load. 3 refs., 12 figs., 4 tabs.

  2. Thermal boundary condition effects on forced convection heat transfer. Application of a numerical solution of an adjoint problem; Kyosei tairyu netsudentatsu mondai ni okeru netsuteki kyokai joken no eikyo. Zuihan mondai no suchi kai wo mochiita kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Momose, K.; Saso, K.; Kimoto, H. [Osaka University, Osaka (Japan). Faculty of Engineering Science

    1997-11-25

    We propose a numerical solution for the adjoint operator of a forced convection heat transfer problem to evaluate mean heat transfer characteristics under arbitrary thermal conditions. Using the numerical solutions of the adjoint problems under Dirichlet and Neumann conditions, both of which can be computed using a conventional CFD code, the influence function of the local surface temperature on the total heat transfer and that of the local surface heat flux on the mean surface temperature are obtained. As a result, the total heat fluxes for arbitrary surface temperature distributions and the mean surface temperatures for arbitrary surface heat flux distributions can be calculated using these influence functions. The influence functions for a circular cylinder and for an in-line square rod array are presented. 14 refs., 9 figs., 1 tab.

  3. Toxicity assessment of organochlorine compounds detected in water environment using cultured human cell lines; Hito yurai saibo baiyokei wo mochiita suikankyo shiryochu no yuki enso kagobutsu no dokusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kunimoto, M; Yonemoto, J; Soma, Y; Nakasugi, O [National Institute for Environmental Studies, Tsukuba (Japan)

    1997-11-10

    As part of validation processes of in vitro toxicity assays for the risk assessment of environmental hazards, we applied an in vitro toxicity test using two human cell lines, neuroblastoma NB-1 cells and glioblastoma U-87 MG cells, to the assessment of organochlorine compounds detected in the water environment. The in vitro toxicity assay using NB-1 cells was calibrated by testing reference chemicals proposed by MEIC (Multicenter Evaluation of In Vitro Cytotoxicity), an international program for the validation of in vitro cytotoxicity assays. Beforehand, an assay using cells in frozen stock without subcultivation was examined by comparing IC50 values with the ordinary assay using subcultured cells. IC50 values for MEIC reference chemicals from the former assay showed good correlation with those from the latter assay, suggesting that the assay using cells in frozen stock can be used at least for the assessment of basal cytotoxicity. IC50 values for ten organochlorine compounds frequently detected in the sediment samples from contaminated rivers, p-chloroaniline, 3,4-dichloroaniline, p-dichlorobenzene, o-dichlorobenzene, Tris (2-chloroethyl)-phosphate, 2,5-dichlorophenol, 2,5-dichloroanisol, Triclosan and Triclocarban, were obtained with the in vitro assays and compared with their LD50 values in rats. No significant correlation, however, was seen between the IC50 and LD50 values, indicating that further improvement of in vitro toxicity assays is necessary for the application to the risk assessment of environmental hazards. 7 refs., 4 figs., 1 tab.

  4. Report on the FY 1999 study of the decomposition/removal of environmental pollutants using laser induced chemical reaction; 1999 nendo laser yuki kagaku hanno wo mochiita kankyo osen busshitsu no bunkai jokyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the cleavage of carbon-chlorine connection and decomposition of benzene rings which are hazardous causes of the environmental pollutants represented by dioxins, the photolysis of gaseous phase chlorobenzene used as a model compound was made using KrF and ArF excimer laser. The decomposition is high efficiency, and ArF shorter in wavelength can be compounded twice-four times as fast as KrF. It was found out that in the system where oxygen exists, carbon monoxide, carbon dioxide, acetylene, hydrogen chloride, etc. are produced as decomposition products. From the results of the gaschromatographical analysis, chlorine compounds were detected as solid phase decomposition products. However, by the oxygen existence effect and laser shorter wavelength effect, the formation of polychlorinated aromatics was controlled, and chlorine compounds were made non-pollutant together with the composition. It was indicated that the environmental clean-up technology using laser is effective for making low-concentration environmental pollutants non-pollutant, and it is a method to clean up the environment which has a wide range of the application field. (NEDO)

  5. One-pot synthesis of hybrid gel by use of tributylstannyl ester of polymeric silicic acid, chlorosilane and organic monomer; Keisan no toribuchiru sutanniru esuteru kobuntai, kuroroshiran oyobi yuki monoma wo mochiita haiburiddo geru no ichidankai gosei

    Energy Technology Data Exchange (ETDEWEB)

    Moriya, O. [National Defense Academy, Kanagawa (Japan). Dept. of Chemistry; Sugisaki, T. [Lintec Co. Ltd., Saitama (Japan); Tomono, M.; Oikawa, M.; Kageyama, T. [Kanto-Gakuin Univ., Kanagawa (Japan)

    1999-12-10

    Organic-inorganic hybrid gels were obtained efficiently by one-pot procedure from tributylstannyl ester of polymeric silicic acid (PTBS), chloro (3-methacryloyloxypropyl) dimethylsilane (1a), and common monomers such as styrene, acrylonitrile, and methyl methacrylate. In the reaction system, substitution of tributylstannyl groups of PTBS by silyl groups of 1a and copolymerization of methacryloyloxy group of 1a with a monomer proceeded simultaneously under UV irradiation at room temperature. The resulting gel should be consisted of covalently bonded three components an regarded as a nanocomposite material The use of another chlorosilane 1b, which had cyanopropyl group, with 1a led to formation of a multifunctional hybrid gel. (author)

  6. Report on achievements in fiscal 1998. Development of foaming eco-material using magazine waste papers. (The first fiscal year); 1998 nendo zasshi koshi wo mochiita happo seikei eko material no kaihatsu seika hokokusho (dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Such foaming materials as styro-foam, urethane and polyethylene greatly increase load on the environment when discarded, and are a problem as harmful rubbish. On the other hand, magazine waste papers have limitation as regenerated paper because their pulp fibers are cut off and deteriorated during use and regeneration. They are left unused without a prospect of re-use even if recovered. Under such a background, the present research and development is intended to develop magazine waste papers as a reusable cushioning material, commercialize the cushioning material as a low environment load type material, and promote reutilization of magazine waste papers. Specifically, development is performed on a manufacturing technology and a manufacturing equipment for a cushioning material having excellent biodegradation performance manufactured by mixing magazine waste papers with gelatin as a binder, and further by foaming and forming. The research and development items include: (1) development of a manufacturing technology for a foaming eco-material using magazine waste papers, (2) development of manufacturing equipment for the foaming eco-material, and (3) the market research thereon. This paper reports the achievements in the research and development of each item in fiscal 1998. (NEDO)

  7. Estimation of real ship propelling performance by the surface velocity lattice method using model ship flow field data; Mokeisen ryujo data wo mochiita hyomen uzu koshiho ni yoru jissen suishin seino no suitei

    Energy Technology Data Exchange (ETDEWEB)

    Kai, H; Ikehata, M; Sakai, S [Yokohama National University, Yokohama (Japan). Faculty of Engineering

    1997-10-01

    This is basically a technique wherein the wing element method is replaced by a surface vortex lattice method. A horseshoe vortex of unknown intensity and source surface of known intensity are distributed on the wing surface and, under conditions that the fluid will not cross the boundary, the intensity of horseshoe vortex circulation is calculated for the solution of the fluid field. For the simulation of a real ship in navigation, the required propeller revolution thrust is determined using the real ship resistance value and real ship thrust reduction factor estimated from a model ship resistance test by extrapolation. The calculation of propeller performance is conducted in the quasi-steady condition using the force of fluid working on one wing for each wing angle (with the wing rotated at the increment of 6 degrees), and the thrust and torque are determined using the averages of values obtained in one cycle. It is found that the torque value is overestimated in a considerable degree in the wing element theory. In the surface vortex lattice method, both thrust and torque values agree with experimental values mostly, and this method is found to be accurate enough as a navigation element calculation tool when many panels are considered. 4 refs., 5 figs., 1 tab.

  8. Preparation of ZrO2 thin films by CVD using H2-CO2 as oxidizer. H2-CO2 wo sanka gas ni mochiita CVD ho ni yoru ZrO2 maku no sakusei

    Energy Technology Data Exchange (ETDEWEB)

    Aizawa, M; Kobayashi, C [Toto Ltd., Kitakyushu (Japan); Yamane, H; Hirai, T [Tohoku University, Sendai (Japan). Institute for Materials Research

    1993-02-01

    This report describes an outline on the results of investigation on the formation of ZrO2 films from [beta]-diketone chelate of Zr using H2/CO2 as oxidizing gas by application of the CVD method at a temperature as high as 1000[degree]C. The deposition rate is 4[mu]m/h at 650[degree]C, increases with rise of temperature and reaches 10[mu]m/h at 900-1000[degree]C. No lowering of the rate at high temperature seems to be caused by temperature dependence of water (increase of water concentration above 850[degree]C). The physical form of ZrO2 is black and amorphous at 650[degree]C; grey and tetragonal at 850[degree]C; white, monoclinic and tetragonal at 950-1000[degree]C. All of these films showed a fine-grain, polycrystalline structure at any temperature and became white by heat-treatment at 1100[degree]C for 100h. This treatment gave no change to amorphous films but transformed tetragonal films and the mixture films of tetragonal and monoclinic crystals into white monoclinic Zr films. This may be because oxygen defects were present in black and grey films of low deposition temperature due to insufficient oxydation of raw material by H2O. Instability of tetragonal crystals seems to be attributed to participation of oxygen defects. In conclusion, possibility of high-temperature film formation was confirmed. 17 refs., 4 figs.

  9. Fiscal 1999 research result report. Basic research on the evaluation method of deep water by fine algae; 1999 nendo bisai sorui wo mochiita shinsosui hyokaho ni kansuru kisoteki kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Basic research was made on establishment of a bioassay for testing the effect of deep water on surface biota. Mixing of surface water and deep water with high-concentration nutrient salts has effect on fine algae (phytoplankton) immediately. In this research, based on conventional AGP (algae growth potential) method as water quality evaluation method by fine algae, the multiplication potential of 13 strains of algae in Kochi's and Toyama's deep water was evaluated by using the increase rate of the number of cells. The research result showed that (1) deep water has the potential increasing cell concentrations of every fine algae to several times or over ten times as compared with surface water, (2) most of both nitrogen and phosphorus in deep water are consumed during the above process, (3) cell concentrations of both harmful and usable species increase, and (4) although no difference in mean potential is found between Kochi's and Toyama's deep water, the patterns of strains promoting multiplication are different between them. (NEDO)

  10. Development of constructed wetland using hydroponic biofilter method for purification of hyper-eutrophic lake water; Fueiyoka kosui no joka no tameno suiko seibutsu rokaho wo mochiita jinko shicchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Aizaki, M. [Shimane Univ., Matsue (Japan)] Nakasato, H. [Top Ecology Co. Ltd., Tokyo (Japan)

    1997-09-10

    Applying the hydroponic biofilter method as a direct purification method for a hyper-eutrophic lake water, an experiment was carried out at the Tsuchiura Port on Lake Kasumigaura to obtain data for constructing a hydrophilic artificial wetland. Purification of hyper-eutrophic lake water containing a large amount of water blooms in summer was attempted applying the hydroponic biofilter method for which hydrophyte is used. As a result, it was clarified, by applying the hydroponic biofilter method, that capturing effect of suspended substances can be achieved in the rooting zone, captured suspended substances are decomposed at high rate, and the revolved nutrient salt can be absorbed and assimilated by the use of plants having high growth rates. Ipomoea aquatica had the highest removal activity, followed by nasturtium officinal, menthe spicata, and oenanthe javanica. As a result, it became clear that a constructed wetland made with the hydroponic biofilter method can be applied as a direct purifying method for hyper-eutrophic lake water by selecting appropriate plants in accordance with season. 18 refs., 1 fig., 4 tabs.

  11. Synthetic focused array of electrical prospecting using pole-pole array potential data; Sanjigen denki tansaho ni okeru nikyokuho den`i data wo mochiita denryu shusoku haichi no goseiho

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, K [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-10-22

    Various methods have been put into practice for the conventional two-dimensional pole configuration using a single line in three-dimensional electrical prospecting. Pole configuration effective for the three-dimensional exploration has not been investigated. This paper describes synthetic focused array using four pairs of guarded poles based on pole-pole array potential data in the case of arrangement of measuring points on a grid. Results of the numerical simulation are also described. For the focused array, laterolog of electrical logging is applied to the surface prospecting. Directivity can be given to the current from the main pole by controlling the current from guarded pole. It was found from the simulation that the resistivity anomaly is concentrated directly on the embedded ball for the focused array rather than for the pole-pole array. It was also found that two conductive balls can be clearly separated for the focused array rather than for the dipole-dipole array. Accordingly, it was considered that results approximating the original structures can be obtained by analyzing using the both arrays. 5 refs., 6 figs.

  12. Consideration of the reservoir by the temperature history at the Hijiori HDR (hot dry rock) wells; Hijiori koon gantai no kokukosei ni okeru ondo rireki wo mochiita choryuso no kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, W; Shinohara, N; Osato, K; Takasugi, S [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan)

    1997-10-22

    Hot dry rock (HDR) power generation has been promoted by NEDO since 1984 at Hijiori, Okura village, Mogami-gun, Yamagata Prefecture. Hydraulic fracture tests and circulation tests have been conducted using four wells named as SKG-2, HDR-1, HDR-2 and HDR-3. Based on these test results, flow models of Hijiori shallow and deep reservoirs have been proposed. Conventional circulation tests have been analyzed only using temperature profile data. In this paper, circulation tests are analyzed by numerical simulation, to discuss individual characteristics of the shallow and deep reservoirs. Injection flow, production flow and circulation days were inputted as past circulation test data, to discuss the characteristics of geological layers, especially the permeability data, by which the features of temperature profiles in each well can be explained. As a result, it was found that the extension of permeable zone affecting the temperature in the SKG-2 well equivalent to the shallow reservoir was larger than that in the HDR-1 well. It was also found that there was a large difference in the permeability between the HDR-2a and HDR-3 wells. 5 refs., 8 figs., 2 tabs.

  13. Fundamental study on the interpretation technique for 3-D MT data using neural networks. 2; Neural network wo mochiita sanjigen MT ho data kaishaku gijutsu ni kansuru kisoteki kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Fukuoka, K; Kobayashi, T [OYO Corp., Tokyo (Japan); Mogi, T [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Spichak, V

    1997-10-22

    Behavior of neural networks relative to noise and the constitution of an optimum network are studied for the construction of a 3-D MT data interpretation system using neural networks. In the study, the relationship is examined between the noise level of educational data and the noise level of the neural network to be constructed. After examination it is found that the neural network is effective in interpreting data whose noise level is the same as that of educational data; it cannot correctly interpret data that it has not met in the educational stage even if such data is free of noise; that the optimum number of neurons in a hidden layer is approximately 40 in a network architecture using the current system; and that the neuron gain function enhances recognition capability when a logistic function is used in the hidden layer and a linear function is used in the output layer. 2 refs., 7 figs., 2 tabs.

  14. Study on deep crustal resistivity structure using wideband magnetotellurics. In the case of eastern part of Hokkaido, Japan; Kotaiiki MT ho wo mochiita shinbu chikakuhi teiko kozo no kenkyu. Hokkaido Tobu chiiki ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H; Tanimoto, K; Maeda, T; Nishida, Y [Hokkaido University, Sapporo (Japan); Takada, M; Tamura, M [Hokkaido University, Sapporo (Japan). Research Center of Earthquake Prediction; Ogawa, Y [Geological Survey of Japan, Tsukuba (Japan); Nagao, T [Tokai Univ., Tokyo (Japan)

    1997-10-22

    Wide-range MT (magnetotelluric) observation is conducted to collect knowledge of the middle and lower parts of the crust of the above-named region, about which but a little information is available, for comparison with information about Kurile islands arc tectonics. Three traverse lines crossing the Kurile islands roughly in the north-south direction and two lines running from east to west are used, with the observation stations totalling 48. The distance between observation stations is 7-8km on the Nijibetsu line, and approximately 15km on the Nakashibetsu and Akan lines. A very wide frequency range of 320-0.0005Hz is used for measuring, and these results in detection with success of resistivity structure details from shallow to deep layers in the crust. The collected data are analyzed, and it is estimated that the northern and central parts have a high-low-high three-layer structure while the southern part has a low-high two-layer structure. Since the data obtained at observation stations at the middle of the lines, in particular, have an extremely low apparent value of several ohm/m at about 1Kz in the absence of splits in the TM (transverse magnetic) and TE (transverse electric) modes, it is inferred that the low-resistivity layer is considerably thick and is distributed rather uniformly. 13 refs., 5 figs.

  15. Estimation of site effects in Higashinada Ward, Kobe City using aftershock records of the 1995 Hyogo-Ken Nanbu Earthquake; Hyogoken nanbu jishin no yoshin kiroku wo mochiita Kobeshihigashinadaku no jiban zofuku tokusei no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kurita, K.; Yamanaka, H.; Seo, K. [Tokyo Inst. of Tech. (Japan)

    1998-07-30

    Source spectra and site effects are separated using the aftershock records, and the characteristics of short period earthquake motion in Higashinada Ward, Kobe City including the area to the south of seismic intensity 7 area are investigated placing emphasis on how far the site effects can be explained by 1-D ground structure. The shape and amplitude of the site effect of KNN and KYC located outside the seismic intensity 7 area can be explained fairly well by 1-D multiple reflection theory of S wave. However, peaks near 3 to 4Hz of KNN and UOZ in seismic intensity 7 area can not be explained. This suggests that the site effects of seismic intensity 7 area obtained by the aftershock records might include 2-D effects of underground structure. Inversion is performed using site effects as the objective functions to determine S wave velocity structure and Qs in the sedimentary layer. S wave velocity structure shows no systematical difference from those of the past models. 22 refs., 13 figs., 2 tabs.

  16. Coal demineralization with Ca(OH)2. Hydrothermal reaction between Ca(OH)2 and quartz; Ca(OH)2 wo mochiita sekitan no kagakuteki dakkai. Ca(OH)2 to sekitan no suinetsu hanno

    Energy Technology Data Exchange (ETDEWEB)

    Wang, J.; Tomita, A. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

    1996-10-28

    Coal demineralization mechanism and its optimum condition were studied by hydrothermal reaction between Ca(OH)2 and quartz as a coal demineralization model. In experiment, the mixture of powder quartz and Ca(OH)2 water slurry was subjected to reaction in an autoclave under spontaneous pressure at 175-340{degree}C. After dried in N2 gas atmosphere at 105{degree}C, the reaction product was analyzed by X-ray diffraction, thermo-balance and differential thermal analysis. In measurement of quartz conversion, the specimen was analyzed by X-ray diffraction after removal of bound water by heat treatment at 850{degree}C. The mixture of clean coal deashed by NaOH and a fixed amount of quartz was also used as specimen for experiment. As the experimental result, dicalcium silicate hydrate was mainly produced at 175{degree}C, and the product changed into xonotlite through tobermorite by longer treatment at higher temperature. For complete reaction of quartz, heat treatments for 7 and 5 hours at 300 and 400{degree}C were necessary, respectively. 2 refs., 2 figs., 2 tabs.

  17. BTX production by in-situ contact reforming of low-temperature tar from coal with zeolite-derived catalysts; Zeolite kei shokubai wo mochiita sekitan teion tar no sesshoku kaishitsu ni yoru BTX no seisei

    Energy Technology Data Exchange (ETDEWEB)

    Matsunaga, T.; Fuda, K.; Murakami, K.; Kyo, M.; Hosoya, S.; Kobayashi, S. [Akita University, Akita (Japan). Mining College

    1996-10-28

    On BTX production process from low-temperature tar obtained by pyrolysis of coal, the effect of exchanged metallic species and reaction temperature were studied using metallic ion-exchanged Y-zeolite as catalyst. In experiment, three kinds of coals with different produced tar structures such as Taiheiyo and PSOC-830 sub-bituminous coals and Loy Yang brown coal were used. Y-zeolite ion-exchanged with metal chloride aqueous solution was used as catalyst. Zn{sup 2+}, Ni{sup 2+} and In{sup 3+} were used as metal ions to be exchanged. The experiment was conducted by heating a pyrolysis section up to 600{degree}C for one hour after preheating a contact reforming section up to a certain proper temperature. As a result, the Ni system catalyst was effective for BTX production from aromatic-abundant tar, while the Zn system one from lower aromatic tar. In general, relatively high yields of toluene and xylene were obtained at lower temperature, while those of benzene at higher temperature. 4 figs., 1 tab.

  18. Design and construction of radiant panel for cooling and heating with photovoltaic and thermoelectric element modules; Taiyo denchi to netsuden soshi module wo mochiita fukusha reidanbo panel no sekkei oyobi shisaku

    Energy Technology Data Exchange (ETDEWEB)

    Sato, M; Tani, T [Science University of Tokyo, Tokyo (Japan); Kadotani, K; Imaizumi, H [Komatsu Ltd., Tokyo (Japan)

    1997-11-25

    Utilizing cooling properties and current voltage characteristics of a small cooling panel using thermoelectric elements which had been fabricated previously on a trial basis, design and prototype production were executed on a large radiant cooling and heating panel driven by photovoltaic cell modules. The panel design set the cooling area to about 0.5 m {sup 2} and the number of elements to 70 pieces, and optimum number of elements in series and parallel connection was derived. As a result of the analysis, it was made clear that the optimum number of thermoelectric module arrays in series and parallel connection varies depending on insolation intensity. It was found preferable that the number of parallel connection array be set to one to two in a region or time period in which low insolation intensity is distributed in greater amount. In the case where high insolation intensity is distributed in a greater amount, setting it to two to three is preferable. By using the structured design method and the HASP Tokyo data, thermoelectric element modules were interconnected with 35 modules in series and two in parallel on a cooling panel installed on the roof of the Science University of Tokyo. A simulation result revealed that the average temperature difference on the cooled surface in summer is 4.37 degC, and the solar cell utilization rate is 0.67. It is necessary in the future to improve heat dissipation efficiency and area ratio. 1 ref., 12 figs., 5 tabs.

  19. Study of a wave power generator system using an air turbine having improved J-shaped blades; Kairyo J gatayoku kuki turbine wo mochiita haryoku hatsuden sochi no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Honma, T; Omata, K; Kojima, N [Meiji University, Tokyo (Japan)

    1997-11-25

    An improved J-shaped blade, in which a J-shaped blade is combined with a small-size Savonius blade, has been developed, to further improve efficiency of an air turbine for wave power generator systems. A prototype model of stationary wave power generator has been developed using the improved blade, to confirm its power generation characteristics by tests in a water tank and small-scale ocean tests. The results are compared with the characteristics of the units with conventional blades. The air turbine unit with the improved blade shows an efficiency of 13 to 35%, which is higher by 10 to 20% than that of the turbine with a J-shaped blade and by 20 to 70% than that of the one with a Savonius blade, more noted at low speed of rotation. It is therefore considered that the turbine with the improved blade is suited for sea areas having a relatively low wave height. It is also considered that efficiency can be further enhanced, when one or more guide vanes are provided around the blade. 2 refs., 12 figs.

  20. Study on high concentration solar concentrator using a Fresnel lens with a secondary concentrator; Fresnel lens to niji shukokei wo mochiita solar chemistry yo kobairitsu shukokei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Aihara, T; Suzuki, A; Fujibayashi, K [Tokyo University of Agriculture and Technology, Tokyo (Japan)

    1997-11-25

    A high concentration light collection system for solar chemistry was devised by using an inexpensive Fresnel lens in a primary concentration system and a conical type concentrator in a secondary concentration system. A Fresnel lens alone would not achieve sufficiently high light collecting magnification to attain high temperatures because of restrictions in the opening angle as seen from a focus. Therefore, a secondary concentration system was installed on a focus for an attempt of stopping. Reflection plane of a three-dimensional compound parabolic concentrator (CPC) is a rotary parabolic plane, whose process is expensive because of its surface processing accuracy. Therefore, a conical type concentrator was employed as a secondary concentration system. This system may not be capable of achieving as high concentration as in the CPC, but its shape is simple and it is inexpensive. In its optimization, a complete black body surface placed in vacuum atmosphere was hypothesized as a light concentrating part for the secondary concentration system to calculate heat collecting efficiencies at respective temperature settings. Using simultaneously the secondary concentration system, rather than collecting heat by using a Fresnel lens alone, has attained as high value as from 5.99% (500 degC) to 43.47% (1400 degC). Economical high-temperature heat collection of solar chemistry level may be possible by using a Fresnel lens and a conical secondary concentration system. 1 ref., 7 figs., 2 tabs.

  1. Estimation of water-coal surface interaction during heat treatment of coal by use of FTir and DSC; FTir to DSC wo mochiita sekitan-mizu kan sogo sayo no teiryoteki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Miura, K.; Mae, K.; Morozumi, F.; Kusakawa, T. [Kyoto University, Kyoto (Japan)

    1997-10-30

    The authors have recently presented a method to estimate the strength distribution of hydrogen bondings in coal using FTir and DSC. The method was applied to estimate the strength of coal-water interaction in two different coals and to estimate the enthalpy change deriving from the change in hydrogen bondings during the desorption of water. The estimated enthalpy change was compared with the total enthalpy change estimated by DSC measurement to examine the importance of hydrogen bondings during the desertion of water. 1 ref., 6 figs.

  2. Fault-related-folding structure and reflection seismic sections. Construction of earth model using balanced cross section; Danso ga kaizaisuru shukyoku kozo no keitai to jishin tansa danmen. 1. Balanced cross section wo mochiita chika model no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Tamagawa, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    Pre-stacking depth migration treatment is studied for the estimation of the fold configuration from seismic survey cross sections. The estimation of a velocity structure is necessary for the execution of such treatment, and the utilization of structural-geological knowledge is required for its interpretation. The concept of balanced cross section in relation to the fault-bend fold constructs a stratum structure model under conditions that the deformation during fold and fault formation is a planar strain, that there is no change in volume due to deformation, and that a fold is a parallel fold. In addition to the above geometric and kinetic approach, there is another fold formation process simulation model using a Newtonian fluid for study from the viewpoint of dynamics. This simulation stands on the presumption that the boundary contains a ramp that had been in presence before fold formation and that an incompressible viscous matter is mounted on the top surface. The viscous matter flows and deforms for the formation of an anticline on the ramp. Such enables the reproduction of a fault-bend fold formation process, and helpful discussion may be furthered on the dynamic aspect of this simulation. 5 refs., 4 figs.

  3. Advanced mineral and lithological mapping using high spectral resolution TIR data from the active CO2 remote sensing system; CO2 laser wo mochiita kosupekutoru bunkaino netsusekigai remote sensing data no ganseki kobutsu shikibetsu eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Okada, K [Sumitomo Metal Mining Co. Ltd., Osaka (Japan); Hato, M [Earth Remote Sensing Data Analysis Center, Tokyo (Japan); Cudahy, T; Tapley, I

    1997-05-27

    A study was conducted on rock/mineral mapping technology for the metal ore deposit survey using MIRACO2LAS, an active type thermal infrared ray remote sensing system which was developed by CSIRO of Australia and is now the highest in spectral resolution in the world, and TIMS of NASA which is a passive type system. The area for the survey is the area of Olary/Broken Hill and Mt. Fitton of Australia. A good correlation is seen between the ground reflectance measured by MIRACO2LAS and the value measured by the chamber CO2 laser of rocks sampled at the above-mentioned area. In case that the width of spectral characteristics is below 300nm, the inspection ability by MIRACO2LAS`s high spectral resolution is more determined in mineral mapping as compared with TIMS which is large in band width. Minerals mapped using MIRACO2LAS are quartz, talc, amphibole, hornblende, garnet, supessartine, dolomite, magnesite, etc. 4 refs., 3 figs.

  4. Improvement in performance of nonequilibrium disk MHD generator by radio-frequency pre-ionization; Hiheiko disk gata MHD hatsudenki ni okeru koshuha yobi denri wo mochiita seino kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, T.; Okuno, Y.; Kabashima, S. [Tokyo Institute of Technology, Tokyo (Japan)

    1998-03-01

    Validity of improvement in performance of a nonequilibrium disk-type MHD generator by applying an additional radio-frequency (rf) electromagnetic field is investigated with r-{theta} two-dimensional numerical simulation. In particular, the structure of the plasma is examined in relation to the generator performance. The inductively coupled pre-ionization at an upper region of the charmer results in the increase of the electron temperature of the plasma. Thus, the nonuniformity of the plasma caused by the ionization instability developing in a weakly ionized seed plasma can be relieved and the fluctuation of the electron temperature and the ionization degree of the seed atoms are also suppressed. As the coil current is increased, the plasma behavior changes from the nonuniform state to the uniform stable state through the unstable transient state. As a result, the enthalpy extraction of the generator is improved. The ratio of the required Joule heating by the rf electric field for the sufficient improvement in the performance to the thermal input of generator is estimated to be about 0.35%. 11 refs., 5 figs., 1 tab.

  5. Evaluation on diminishing effects of DNA damaging potential by humic substances using the bacillus subtilis rec-assay; Karekusakin rec-assay wo mochiita fuminsan ni yoru DNA sonshosei kaizen koka no kento

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H.; Takigami, H.; Shimizu, Y.; Matsui, S. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1998-05-22

    Antimutagenic effect of humic substances has been reported by various investigators. In this research, the diminishing effect of DNA damaging toxicity by humic acid was evaluated for the influent and effluent of activated sludge tank receiving municipal wastewater and several DNA damaging chemicals (e.g., pyrene, 1-aminopyrene and benzo(a)pyrene) using Bacillus subtilis rec-assay. The diminishing effect was not apparent for influent but observed in the effluent. Among the DNA damaging chemicals, the DNA toxicity was effectively suppressed by humic acid for pyrene and benzo(a)pyrene. However, the effect was relatively smaller for 1-aminopyrene. 19 refs., 6 figs., 6 tabs.

  6. Development of CO2 fixation system at a sludge incinerator by a unicellular green alga chlorella; Gesui odei shokyaku shisetsu ni okeru kurorera wo mochiita CO2 kotei system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Misonou, T. [Yamanashi Univ., Yamanashi (Japan). Faculty of Pedagogy; Morimoto, K. [Yamanashi Univ., Yamanashi (Japan). Graduate School; Suzuki, Y. [Yamanashi Univ., Yamanashi (Japan). Faculty of Engineering

    1997-03-05

    Among many environmental problems now the world is facing with, the increase of CO2 concentration in the atmosphere is considered to give rise to many phenomena causing such serious effects as abnormal weather, water shortage, food shortage, etc., hence predictions by climate models are being tried at many places in the world, and any of them predicts a temperature rise due to the increase of gases such as CO2 causing the green house effect. In this article, an experiment has been carried out which cultures chlorella capable of fixing CO2 by using the exhaust gas actually emit from the sludge incinerator inside the South Sewage Purification Center of Kofu City, Yamanashi Prefecture. As a result, it has been theoretically concluded that a CO2 fixation system can be constructed inside the above center, but it is necessary to consider the balance between working electric energy during the system operation and the amount of CO2 fixation by the above system. In case when the electric power from a commercial power plant is used for the operation of the system, such usage becomes meaningless unless the system fixes CO2 more than the CO2 discharge by this power generation. 11 refs., 5 figs., 4 tabs.

  7. Droplet size measurement of diesel fuel spray particles using a planar laser-induced fluorescence method; Nijigen laser yuki keikoho wo mochiita diesel funmu ryushi no ryukei keisoku ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, N. [Isuzu Motors Ltd., Tokyo (Japan); Niimura, K. [Nissan Diesel Motor Co. Ltd., Saitama (Japan); Tsujimura, K.

    1997-11-25

    In this study, the planar laser-induced fluorescence (PLIF) technique was used to measure the mean size and size distribution of diesel spray particles. The fuel used was n-tridecane mixed with 1 wt% N, N, Nprime, Nprime-tetramethylparaphenyenediamine (TMPD). The light source used to excite the TMPD in the fuel was a secondary harmonic of a ruby laser-light sheet. A highly magnified image of the fluorescence from TMPD was taken by a 35 mm still camera with magnified optics, and the mean particle size and particle size distribution of the fuel spray were determined by processing the images of fuel particles printed on paper. First, the accuracy of this method was confirmed by comparison with results of Phase Doppler Anemometry for fuel spray of an air-assisted gasoline injector. Then, for the diesel spray, the effects of injection velocity, ambient pressure, geometric configuration of nozzle hole (i.e., nozzle hole diameter and nozzle hole L/D) and of measurement points on the fuel particle mean size and size distribution in a high-pressure vessel at atmospheric temperature were investigated. The results showed that the small size particles increase in number with increasing injection velocity. At higher injection velocity, seem to atomize more actively. With increasing ambient pressure, the mean particle size increases. A reduction in nozzle diameter resulted in no improvement of atomization in this study. Also, the mean particle size in the downstream region of the spray is larger than that in the upstream region of the spray. 16 refs., 19 figs., 3 tabs.

  8. Evaluation report on the development of energy conservation/environment purification system using cleaning effect of optical irradiation; Hikari clean gijutsu wo mochiita sho energy kankyo joka system no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The results achieved in fiscal 1992-1995 under the above-named project are stated. In the development of photocatalytic materials, a photocatalytic fluorocarbon polymer sheet suitable for use in a denitration apparatus is developed. A high density fluorocarbon polymer sheet composed of TiO{sub 2} modified with 0.3% of Pd/absorbent zeolite/fluorocarbon polymer PTFE (polytetrafluoroethylene) =48-63/24-36/10-20 is fabricated, which achieves a level higher than the denitration goal of 70%. Although the sheet in a 500-hour accelerated exposure test undergoes a hardening phenomenon in which elasticity decreases and tensile strength increases, yet degradation is hardly detected. Although a slight reduction is detected in denitration efficiency, yet it does not affect its practical application, and thus the durability goal is achieved. In the development of an energy conservation type air cleaning apparatus usable in underground parking areas or motorway tunnels, an apparatus capable of treating air at a rate of 2,000m{sup 3}/hour is fabricated, and this achieves a denitration level of not less than 80% in a field test (in the absence of rainfall). For denitration in the presence of rainfall, the apparatus is combined with an equimolar adsorption system, and a system capable of 80% denitration is proposed on the basis of data actually measured for each of the two. A conceptual design for a service model comprising a photodenitration and equimolar adsorption systems is evaluated, and it is found that it occupies less space than the existing models. (NEDO)

  9. Measurement of friction coefficient for various thin films using millimeter-size movers driven by electro-static force. Seiden kudogata bisho mover wo mochiita usumaku no masatsu keisoku

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, M; Watanabe, S; Yoshimura, N [Akita Univ., Akita (Japan); Fujita, H [The University of Tokyo, Tokyo (Japan)

    1992-12-20

    Discussions were given on measurements of coefficients for static friction between different types of thin films. A small light-weight mover of a millimeter size was driven electrostatically to measure friction in a condition close to operation of a micromachine. The thin film materials were fabricated using a sol-gel process, sputtering, vacuum deposition and a CVD process. The materials include Ni, Ti, Al, SiO2, SiNx, Si wafers and glasses. The measured values for Ni-Ni, Al-Al and Ni-Al were larger by from 0.1 to 0.2 than values for bulk. The reason for this would be because of the friction generating mechanisms being different and the sample weight being lighter. Measured values for different types of thin films on silicon wafers were higher. This may be because OH groups are formed on the wafer surface causing high adhesiveness. Values for glasses are small in general. Friction coefficients for SiO2 thin films are small on the whole. However, SiO2-SiO2 showed larger values. This indicates that SiO2 is a useful material for micromechatronics, but proper selection of contacting opponents is important. 7 refs., 4 figs., 7 tabs.

  10. Fiscal 2000 achievement report on the development of energy conservation/environment purification system using cleaning effect of optical irradiation; 2000 nendo hikari clean gijutsu wo mochiita sho energy kankyo joka system no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The research aims to develop materials and apparatuses for the purification of atmosphere using titanium dioxide that exhibits a powerful oxidizing capability when irradiated with light. A study is conducted to find out an optimum composition for a photocatalytic fluorocarbon polymer sheet suitable for use in a denitration apparatus. A high density fluorocarbon polymer sheet composed of TiO{sub 2} modified with 0.3% of Pd/absorbent zeolite/fluorocarbon polymer PTFE (polytetrafluoroethylene) =48-63/24-36/10-20 is found to show high denitration efficiency, and this achieves the denitration efficiency goal. As for sheet thickness, 0.75mm is found to be enough. The sheet experiences some hardening in an accelerated exposure test, but does not change much in a surface gloss test or a chalking test. Although a slight reduction is observed in denitration efficiency, yet the durability goal is achieved. In the effort to develop an energy conservation type air cleaning apparatus, field tests and experiments are repeatedly conducted. As for photodenitration in the cleaning apparatus, the number of photodenitration stages and the magnitude of equimolar adsorption area necessary for achieving an 80% denitration rate is calculated from the relations of the NOx concentration profile and the denitration rate in the equimolar adsorption module to (gas flow rate/module surface), and the result shows that the initially intended goal is achieved. (NEDO)

  11. Ultimate strength analysis of thin plated structures using eigen-functions. 3rd Report. Application to reliability analysis; Koyu kansu wo mochiita usuita kozobutsu no dansosei kaisekiho. 3. Shinraisei kaiseki eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Ueda, Y. [Osaka University, Osaka (Japan). Welding Research Institute; Masaoka, K.; Okada, H. [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering

    1996-12-31

    A reliability analysis was performed on ultimate strength of a hull by introducing reliability engineerings into the idealized structural unit method. Elements developed under the present study were applied to a model of an actual structure to indicate that even an analysis requiring much time under the finite element method can be performed in a short time and at high accuracy when this method is used. Analysis acted with bending moment and shear force simultaneously was performed on a model used as a structure in experiments carried out by Nishihara, assuming pure bending moment and longitudinal strength during slamming. Then, a reliability analysis was conducted on the same model based on this analysis method to investigate the ultimate strength. In an analysis of an ultimate strength when bending and shearing that assume slamming act upon simultaneously, axial force in the hull side decreases as loading increases, wherein how the shearing force increases can be identified clearly. Although existence of initial bends reduces the strength, the effect of variance in the vicinity of the average value on the reliability is rather small, while the effect due to variance in yield stress is greater. 27 refs., 14 figs., 4 tabs.

  12. Improvement of algorithm using Kohonen`s self-organizing feature map for the traveling salesman problem; Kohonen jiko soshikika tokucho mappu wo mochiita ukai serusuman mondai kaiho no kairyo

    Energy Technology Data Exchange (ETDEWEB)

    Fujimura, K.; Tokutaka, H.; Tanaka, H.; Kishida, S. [Tottori Univ., Tottori (Japan); Oshima, Y. [Mita Industrial Co. Ltd., Osaka (Japan)

    1996-02-20

    Traveling salesman problem (TSP) is one of the combinatorial optimization problems. The solution of this problem is to seek the way of how to visit every city only once within the shortest traveling distance. The solutions of this problem are studied a lot hitherto since they are the index for observing the basic properties of optimization algorithm. The method of Angeniol using the elf-organizing feature map is greatly forceful from the viewpoint of its short calculating time. In this study, regarding the algorithm of Angeniol, the conditions of obtaining the shortest tour length within shorter time are examined. Namely, a half of calculating time is reduced by changing Angeniol method into the method of making the node create after the searches of M cities. Additionally, the calculating time for unchanged tour length is reduced to one fourth by adding an inertia item in accordance with the variation of the number of total nodes. 14 refs., 8 figs.

  13. Test and research on the production of useful matter with carbon-dioxide-fixed microorganisms. Production of biodegradation plastics with photosynthesized microorganisms. Tansan gas kotei biseibutsu wo mochiita yuyo busshitsu seisan shiken kenkyu. Kogosei biseibutsu ni yoru seibunkaisei plastic seisan

    Energy Technology Data Exchange (ETDEWEB)

    Miyasaka, H. (The Kansai Electric Power Co. Inc., Osaka (Japan))

    1994-07-10

    The present report introduces the basic research on the production of PHB (one of the biodegradation plastics) by utilizing the photosynthesized microorganisms. The indigo algae are conveniently used for the genetic operation, because they are genetically inferior and have plasmid (extranuclear ringed DNA). Therefore, a certain type of oceanic indigo algae was used for the present research. As a vector to introduce the PHB-producing gene into the indigo alga cell, hybrid plasmid was prepared by combining the indigo alga plasmid pAQ1 with colon bacillus plasmid vectors pUC19. The thus prepared vectors had an introduction efficiency into about 1000 cells per one vector. A RuBisCO gene of indigo alga cell was selected as a promoter to heighten the activity of PHB-producing gene in that cell. The gene is being further studied in promotion efficiency by combining it with the above vector and PHB-producing gene. 4 figs.

  14. Hybrid utilization of solar energy. Part 2. Performance analyses of heating system with air hybrid collector; Taiyo energy no hybrid riyo ni kansuru kenkyu. 2. Kuki shunetsu hybrid collector wo mochiita danbo system no seino hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yoshinaga, M; Okumiya, M [Nagoya University, Nagoya (Japan)

    1996-10-27

    For the effective utilization of solar energy at houses, a heating system using an air hybrid collector (capable of simultaneously performing heat collection and photovoltaic power generation). As the specimen house, a wooden house of a total floor area of 120m{sup 2} was simulated. Collected air is fanned into a crushed stone heat accumulator (capable of storing one day`s collection) or into a living room. The output of solar cell arrays is put into a heat pump (capable of handling a maximum hourly load of 36,327kJ/h) via an inverter so as to drive the fan (corresponding to average insolation on the heat collecting plate of 10.7MJ/hm{sup 2} and heat collecting efficiency of 40%), and shortage in power if any is supplied from the system interconnection. A hybrid collector, as compared with the conventional air collector, is lower in thermal efficiency but the merit that it exhibits with respect to power generation is far greater than what is needed to counterbalance the demerit. When the hybrid system is in heating operation, there is an ideal heat cycle of collection, accumulation, and radiation when the load is light, but the balance between accumulation and radiation is disturbed when the load is heavy. 4 refs., 8 figs., 3 tabs.

  15. Study on solar chemical heat pump system. Basic experiment on dehydrogenation of 2-propanol using heteropoly-acid photo catalyst; Solar chemical heat pump no kenkyu. Heteropoly sankei hikari shokubai wo mochiita 2-propanol no dassuiso hanno

    Energy Technology Data Exchange (ETDEWEB)

    Doi, T [Electrochemical Laboratory, Tsukuba (Japan); T-Raissi, A; Muradov, N [Florida Solar Energy Center, FL (United States)

    1996-10-27

    With the purpose of converting solar heat energy to an industrial heat energy, an examination was carried out empirically on the case of using a heteropoly-acid photo catalyst for the decomposition reaction process of 2-propanol. The experiment was performed in Florida Solar Energy Center, in the U.S.A.. The device for the experiment was constituted of a reaction part, distribution manifold for feeding from the lower part of the reaction part a 2-propanol solution for which a photo catalyst was suspended, storage tank served also as a gas-liquid separating container, and circulating pump. Silica-tangstic acid was used as the photo catalyst. In an outdoor experiment using solar radiation, the quantity of inclined global solar radiation was 530-950W/m{sup 2} in clear days and 100-600W/m{sup 2} in cloudy days, with temperatures between 17 and 26{degree}C throughout the experiment period. In addition, an indoor experiment was also conducted using an artificial light source (UV light). As a result of the experiment, the energy conversion efficiency was at most about 1% of incident UV light, a low figure compared to a heat utilization ratio of approximately 15% with a thermal catalyst. 6 refs., 8 figs.

  16. Study on wave power generation of electricity using torsion arc blade type horizontal axis wind turbine; Nejire enko yokugata suihei jiku fusha wo mochiita haryoku hatsuden ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kojima, N; Kishimura, K [Meiji University, Tokyo (Japan)

    1996-10-27

    Windmilling characteristics of a combination of a torsion arc blade type (TABT) horizontal axis wind turbine and a reverse torsion arc blade type (RTABT) horizontal axis wind turbine were evaluated in a wave activated power generation experiment. The TABT wind turbine had six blades, and the front and rear parts of the blade were twisted in the same direction, which caused the direction of rotor rotation to change as the direction of wind along the shaft changed. The RTABT wind turbine had twelve blades, and the front and rear parts of the blade were twisted reverse to each other, which allowed the direction of rotor rotation to stay constant even in the presence of wind direction reversal. To keep the direction of rotor rotation unchanged in the presence of flow direction reversal along the power generating turbine shaft, a single-stage type RTABT wind turbine and a double-stage type were used, the double-stage type being a series connection of a first-stage RTABT (for blowout and suction) and second-stage TABT (for blowout only). Both single-type and double-type rotated in the same direction irrespective of the direction of air flow. The output of the double type was obtained by adding up the values obtained from the individual turbines. The double type was two to three times higher in efficiency than the single type in turbine revolution and power output. 2 refs., 13 figs.

  17. 1998 report on results of R and D project for quick-acting/innovative energy and environment related technology; 1998 nendo kyuchakuzai wo mochiita shinkina tennen gas chozo gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    R and D were conducted for a storing method using an adsorption material concerning methane, the main component of natural gas, with a report made on the 1998 results. In the development of high performance metallic complexes, a molecular design of a material was carried out that has a pore size most suitable for methane adsorption by means of computer simulation, in relation to a metallic complexes on which a rapid improvement of absorptivity can be expected. Consequently, a promising material group was extracted in which an adsorptive capacity of 200-300Ncc/cc can be expected for each of two dimensional copper carboxylate complexs, three dimensional SiF{sub 6} type complexs, and three dimensional hydrogen bond type complexs. As a result of these synthesis by experiment and the examination, a rapid increase in occlusion quantity was recognized in the three dimensional hydrogen bond type complexs. This type uses rhodium, a noble metal and, if synthesis is possible with a lower priced metal, an application can be expected as a general purpose gas absorber. In the R and D of a high performance improved product, the improvement/development of activated carbon was performed, as was the analysis of adsorption-desorption phenomenon, for example. (NEDO)

  18. Comparison of the toxicity of wastewater disinfected with the alternatives to chlorination by bioassay using seaweed (Porphyra yezoensis conchospores); Kaiso (susabinori gai hoshi) wo mochiita seibutsu kentei ni yoru toshi gesui no enso daitai shodoku shorisui no dokusei hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Takami, T.; Maruyama, T.; Suzuki, Y. [Miyazaki University, Miyazaki (Japan). Faculty of Engineering; Kaiga, N. [Toshiba Corp., Tokyo (Japan); Miura, A. [Aomori University, Aomori (Japan). Faculty of Engineering

    1998-11-10

    The technique now in use for disinfecting municipal sewerage is the free chlorine method, and the free chlorine reacts with ammonia in the treated water for the formation of NH4Cl. The resultant compound is strongly toxic and harms aquatic organisms, this creating a knotty problem to solve. In this report, a bioassay utilizing Porphyra yezoensis conchospores is performed, and the toxicity reducing effect is discussed of the seaweed on water specimens disinfected by free chlorine, chlorine dioxide, ozone, and ultraviolet rays. Porphyra yezoensis is easy to acquire, and the bioassay evaluates the toxicity of the water specimens by evaluating the survival rate of conchospores discharged by free-living conchoceles and the rate of inhibited sprouting. The outcome is summarized below. The injection dose required for inactivating 99.9% of the groups of coli bacteria in the treated water and the trend of fluctuations in the concentration level are obtained. No inhibition of conchospore sprouting occurs even with the addition of 100% of treated water in the chlorine-disinfected specimen or chlorine dioxide-disinfected specimen. 19 refs., 8 figs., 2 tabs.

  19. FY 2000 report on the survey on energy conservation technology of large plant using ultra high corrosion resistant materials; 2000 nendo chokotaishokusei zairyo wo mochiita ogata plant no sho energy gijutsu ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of achieving remarkable energy conservation/resource conservation in large plants, the paper carried out an investigational survey of effects obtained in case of applying amorphous super metal which is the newest corrosion resistant material. Amorphous alloys as an ultra high corrosion resistant material are a peculiar material which shows the extremely excellent corrosion resistance even in much strong acid by containing passivated elements with the needed concentration. The corrosion resistant amorphous alloy applied to large plants need the thickness and diameter of more than several millimeters as a bulk material. The subjects are scaling-up of bulk materials and stabilization of characteristics. Even under the tough dew point corrosion environment of the waste power plant, etc., heat recovery from exhaust gas is made possible by heat exchanger applied with ultra high corrosion resistant materials. Effects of the annual heat recovery from the nationwide refuse incinerators and coal thermal power plants are estimated to be approximately 5.2 million kL toe, that is, to be equal to energy conservation of 6 x a million kW class power plant. (NEDO)

  20. Development of movie caption translation lecture site using MobileMotion{sub TM}; MobileMotion{sub TM} wo mochiita jimaku hon'yaku koza site no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The site of Internet that performs the correspondence education for bringing up a movie caption translator was developed. Correspondence education that fully deepens understanding was obtained by distributing a motion picture using MPEG-4 distribution software (MobileMotion{sub TM}) and performing the learning based on bi-directional communication. HTML distribution and E-mail transmission and reception are done from Gaga Communications, and a MobileMotion{sub TM} file is distributed from the OnDemand Server of Toshiba. This reduces the communication traffic of heavy motion picture data. (translated by NEDO)

  1. FY1995 development of artificial arm 'SMART ARM' by spherical ultrasonic motor; 1995 nendo kyumen choonpa motor wo mochiita jinko gishu smart arm no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The project has an intention of development of new type artificial arm by spherical ultrasonic motor. We have succeeded in developing new type of spherical ultrasonic motor with three DOF. And we have succeeded in applying the motor to an artificial arm. This arm have advantages of small size, low weight torque comparing with conventional ones. We demonstrated them the new arm behaved well and it had good controlabilty. (NEDO)

  2. Evaluation of aerodynamic stability and a trial study of construction-accuracy control by daytime measurement of Meiko West Bridge; Meiko Nishi Ohashi no taifusei kento to chukan keisoku kekka wo mochiita kasetsu seido kanri no shiko

    Energy Technology Data Exchange (ETDEWEB)

    Morimoto, C.; Shimodoi, H.; Isoe, A.; Sakai, Y.; Ochiai, M.; Watabe, T.; Ebihara, R. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1998-12-20

    The new Meiko West Bridge was constructed very closely to the phase I line bridge which have been already in a service from 1985, and the distance of this world unique parallel cable-stayed bridges is 50m. The length, span and pylon height of these bridges are identical. By conducting wind tunnel experiments considering the aerodynamic interference of the close parallel bridges, the aerodynamic stability of the bridge had been confirmed during construction as well as complete state. After the construction was completed, the important wind characteristics of the parallel cable-stayed bridges were obtained from the site observation. Regarding cable vibrations, a common problem with cable-stayed bridges, a suitable vibration suppression method was applied based on the site observation. In general, the construction-accuracy control is performed by doing measurement at night However, to study the possibility of the accuracy-control by daytime measurement the measurement was conducted not only at night but also in the daytime. (author)

  3. Determination method of optimum pre-stress in cables of cable-stayed bridges by using fuzzy sets theory; Fuzzy riron wo mochiita shachokyo cable no saiteki prestress chikara ketteiho

    Energy Technology Data Exchange (ETDEWEB)

    Furuta, H. [Kansai Univ., Osaka (Japan); Kaneyoshi, M.; Tanaka, H. [Hitachi Zosen Corp., Osaka (Japan); Kamei, M.

    1996-06-20

    Generally in cable-stayed bridges, optimum pre-stress is introduced into cables to achieve reducing weight of the cable cross section by reducing and equalizing the cross sectional force of the main girders. However, the conventional optimum stress determining methods require setting the cross section to be repeated. Therefore, in order to omit iterative calculations and derive rational pre-stress, a fuzzy sets theory was introduced. With this method, if upper and lower limits of design values (targeted design values) are inputted, which are desired by a designer to be realized as cross sectional force such as in main girders and towers and cable tension, an optimum stress can be derived automatically by means of a fuzzy linearity regression analysis. The targeted design values are given by experience and engineering judgment, and resetting the cross section is not required as long as a target value which can be tolerated by a hypothetical cross section is given. Since the theory used is a fuzzy sets theory, the derived pre-stress may not be guaranteed as a truly optimum pre-stress. In order to have the result approach an optimum solution, it is important to set adequate upper and lower limits of the targeted design values referring to examples of constructions in the past and experience. 10 refs., 11 figs., 7 tabs.

  4. Study on the selection of steel or prestressed concrete cable stayed bridge by using diaggregate behavioral model; Hishukei rojitto model wo mochiita koshachokyo to PC shachokyo no kyoshiki sentaku ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Araki, Y.; Furuta, H.; Maeda, E.; Furukawa, K. [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering

    1994-09-15

    A discussion was given to make clear the selection factors in selecting bridge types (steel cable stayed bridge and prestressed concrete cable stayed bridge). The discussion is intended to consider the future development of both bridges. Quoting a cable stayed bridge with a span length of 250 m that can be selected from either bridge, an evaluation was made by using calculations that uses the disaggregate behavioral model theory based on questionnaire responses from engineers. The analysis uses the following procedure: utility function values of the two term behavioral model (having two choices) are specified and the characteristics variables are selected; the data are prepared according to the specifications, which are used to estimate parameters by a maximum likelihood estimation method; and estimation amount is estimated by using the covariance matrix, which is given a `t` value verification. The conclusions: what gives the large effect to the selection is the engineering capacity and sociality; the result contains vocational consciousness; the economy is measured by the large weight of construction cost for the upper part structures and cost required for large repairs; materials affect largely the reliability, and so does the technological level the constructibility; the comprehensive technical capability, freedom in design and the experience attained by Japan have great effects in terms of technological capability. 10 refs., 10 figs., 11 tabs.

  5. Experimental and analytical study on internal resonances in a cable-stayed beam model. Cableter dot hari model wo mochiita shachokyo no naibu kyoshin ni kansuru jikken to kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Fujino, Y.; Warnitchai, P.; Pacheco, B. (The University of Tokyo, Tokyo (Japan). Faculty of Engineering)

    1991-07-15

    This paper examines the dynamic characteristics on the model of the beam supported by one cable, the most simple type of cable-stayed bridge, with fundamental and important linear and nonlinear internal resonances from the experimental and analytical aspects. Vertical oscillation of the beam is able to cause parametric oscillation of the cable, so that dynamic phenomena which derive from internal resonance such as saturation of amplitude of vertical oscilation of the beam are observed experimentally. Based on the concept of local and global oscillation modes, a 3-DOF(degree of freedom) model is formulated considering the geometric nonlinearity of the cable. Then, a test of a small model, taking notice of linear compound of the cable and the beam as well as autoparametric compound by quadratic nonlinear terms, is conducted under vertical and horizontal harmonic excitations. After identifying the parameter of the model, the experimental value is compared with the analytical value. As a result, it is shown that both of them are highly consistent with each other. 16 refs., 9 figs., 2 tabs.

  6. Ultimate strength analysis of thin plated structures using eigen-functions. 3rd Report. Application to reliability analysis; Koyu kansu wo mochiita usuita kozobutsu no dansosei kaisekiho. 3. Shinraisei kaiseki eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Ueda, Y [Osaka University, Osaka (Japan). Welding Research Institute; Masaoka, K; Okada, H [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering

    1997-12-31

    A reliability analysis was performed on ultimate strength of a hull by introducing reliability engineerings into the idealized structural unit method. Elements developed under the present study were applied to a model of an actual structure to indicate that even an analysis requiring much time under the finite element method can be performed in a short time and at high accuracy when this method is used. Analysis acted with bending moment and shear force simultaneously was performed on a model used as a structure in experiments carried out by Nishihara, assuming pure bending moment and longitudinal strength during slamming. Then, a reliability analysis was conducted on the same model based on this analysis method to investigate the ultimate strength. In an analysis of an ultimate strength when bending and shearing that assume slamming act upon simultaneously, axial force in the hull side decreases as loading increases, wherein how the shearing force increases can be identified clearly. Although existence of initial bends reduces the strength, the effect of variance in the vicinity of the average value on the reliability is rather small, while the effect due to variance in yield stress is greater. 27 refs., 14 figs., 4 tabs.

  7. Fiscal 1998 achievement report on regional consortium research and development project. Venture business fostering regional consortium--Creation of key industries (Development of Task-Oriented Robot Control System TORCS based on versatile 3-dimensional vision system VVV--Vertical Volumetric Vision); 1998 nendo sanjigen shikaku system VVV wo mochiita task shikogata robot seigyo system TORCS no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research is conducted for the development of a highly autonomous robot control system TORCS for the purpose of realizing an automated, unattended manufacturing process. In the development of an interface, an indicating function is built which easily adds or removes job attributes relative to given shape data. In the development of a 3-dimensional vision system VVV, a camera set and a new range finder are manufactured for ranging and recognition, the latter being an improvement from the conventional laser-aided range finder TDS. A 3-dimensional image processor is developed, which picks up pictures at a speed approximately 8 times higher than that of the conventional type. In the development of orbit calculating software programs, a job planner, an operation planner, and a vision planner are prepared. A robot program which is necessary for robot operation is also prepared. In an evaluation test involving a simulated casting line, the pick-and-place concept is successfully implemented for several kinds of cast articles positioned at random on a conveyer in motion. Difference in environmental conditions between manufacturing sites is not pursued in this paper on the ground that such should be discussed on the case-by-case basis. (NEDO)

  8. Fiscal 1998 achievement report on regional consortium research and development project. Venture business raising type regional consortium - small business creating base type (Research and development of Peltier actuating device-aided advanced medical and welfare systems - 2nd year); 1998 nendo Peltier undo soshi wo mochiita kodo iryo fukushi system no kenkyu kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are made to develop a new Peltier actuating device by amalgamating a Peltier device and shape memory alloy and to apply the product to medical and welfare activities. In the development of active movement control for a Peltier actuating device, a multiaxial control system is developed, and a success is attained in high-speed and high-precision control of temperature and in current- and voltage-aided control of the behavior. In the development of an active actuator for catheters, an active catheter is developed for the first time, capable of performing twisting and bending simultaneously. In the development of an artificial heart catheter, an approximately 10cm-long Peltier actuating device is manufactured to serve as an artificial heart module, and a controller is developed to drive the module at the frequency of approximately 0.5Hz. In the development of shape memory alloys and Peltier devices for normal temperature actuation, the impact is examined of the addition of a third element on the transformation temperature and shape memory characteristics. Research and development is also carried out for element technologies for using a Peltier actuating device as an artificial muscle. (NEDO)

  9. Achievement report in fiscal 2000 on research and development project for immediately effective and innovative energy environment technologies. Development of new natural gas storage technology using adsorbents; 2000 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Kyuchaku zai wo mochiita shinkina ten'nen gasu chozo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation with natural gas which contributes to preserving the environment and reducing dependence on petroleum, research and development has been performed on a storage system using adsorbents that allows storage of natural gas at higher density than conventional systems. This paper summarizes the achievements in fiscal 2000. In material development, the current fiscal year has performed the discussions on synthesis of three dimensional complexes. An adsorbent was synthesized successfully that has adsorption performance 2.5 times greater than the secondary complex. In developing an improved activated carbon, an adsorbent was synthesized successfully that has methane adsorption performance four times greater than the compressed gas, by using monolithic activated carbon that uses no binders. Carbon briquettes were manufactured for the basic testing equipment for fuel storage container of natural gas fueled automobiles. In the system development, installation was completed on a bench scale equipment for a gas holder and BOG treatment system, whereas engineering data were acquired from the single-column type high pressure test and two-column type constituent separation and storage test using natural gas. Selection was carried out on applicable vehicle types for the adsorption storage system for natural gas fueled automobiles, and the basic design was made for fabrication of containers of different shapes. (NEDO)

  10. In-situ testing of the liquefaction potential of soft ground using an s-wave vibrator and seismic cones. Part 1. System, concept and preliminary test result; S ha vibrator oyobi seismic cone wo mochiita gen`ichi jiban ekijoka potential no hyoka. 1. System kosei oyobi genchi yosatsu keisoku kekka

    Energy Technology Data Exchange (ETDEWEB)

    Inazaki, T [Public Works Research Institute, Tsukuba (Japan)

    1996-05-01

    For the purpose of evaluating liquefaction in situ, it was proposed that an S-wave vibrator designed to serve as a source in a reflection exploration method be utilized as a strong vibration generating source, and measurement was conducted in this connection. Equipment used in this test included an S-wave vibrator, static cone penetration machine, and various measuring cones. A multiplicity of measuring cones had been inserted beforehand into the target layers and comparison layers, and changes upon vibrator activation were measured. On a dry bed of the Tonegawa river, a 40m{sup 2} field was set up, and 41 cone penetration tests were conducted, with the cones positioned zigzag at 5m intervals. In this way, the ground structure was disclosed from the surface to the 10m-deep level. For the measurement, 3-component cones and seismic cones were placed at prescribed depths, and fluctuations and waveforms presented by pore water pressure at each level were determined with the vibration source changing its place. It was found that the changes in the pore water pressure exposed to vibration assume characteristic patterns corresponding to the conditions of vibration application. 5 figs., 1 tab.

  11. Sensing of subsurface faults based on an imaging technique for teleseismic waveform data. 2. Feasibility study for application to oblique incidence, multi-event and noise data; Enchi jishin hakei data wo mochiita chika kozo imaging ni yoru chichu danso kenshutsu no kokoromi. 2. Naname nyusha, multi event, noise wo fukumu hakei eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Murakoshi, T; Takenaka, H; Saita, T [Kyushu University, Fukuoka (Japan). Faculty of Science; Suetsugu, D [Building Research Institute, Tokyo (Japan); Furumura, T [Hokkaido University of Education, Sapporo (Japan)

    1996-05-01

    An examination was made on the method in which imaging of subsurface was carried out with teleseismic waveform data for sensing of faults. In the examination, an experiment was done on the sensing of faults with higher precision, by applying oblique incidence as well as perpendicular upward incidence of SH plane waves, and thereby stacking the imaging in plural events. In numerical experiments, 28 observation points were arranged at 500m spaces apart on the surface, and the incident waves were made the SH plane waves having a bell-shaped time function, with incidence made at an angle varied as 0{degree}, +15{degree} and -15{degree} from the lowest layer of a model. In the calculation of the wave motion field, a difference calculus with secondary accuracy was used for both time and space. In addition, data was prepared with a random noise added to a synthesized waveform to be used as observation data. The calculated waveform data were likened to the observation waveform, to which the method for imaging faults was applied. Consequently, it was noted that satisfactory results were obtained compared with the case where faults were sensed by one event alone. 5 refs., 4 figs.

  12. FY 1998 report on the results of R and D projects by local consortiums for immediate effects. R and D of high-efficiency, high-performance forming machines (HPFM) using electrophoretic techniques; 1998 nendo denki eido gijutsu wo mochiita kokoritsu takino seikei sochi (HPFM) no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D project has been implemented for novel high-performance forming machines (HPFMs) which handle slurry-based stock materials, in order to impart diversified functions to a wide range of ceramic-based materials covering from traditional to fine ceramic materials, and improve their productivity. For slip casting which uses traditional slurry stock materials, electricity is passed through the work by installing electrodes in each section, to control growth speed and composition of the layers, which are inconceivable by the conventional method for each section. For casting alumina slurry as the fine ceramic-based material, the electrophoretic techniques are also applied, in an attempt to form complex shapes at high efficiency, and to control the inclined structures and compositions/structures at specific sections. For development of the machines on a trial basis for traditional materials, reduction of weight and increasing thickness of the bottom side are attempted for hand-washing bowls, leading to weight reduction of 25% at the maximum. For fine ceramic-based materials, the forming systems are developed, on a trial basis, for fine pipes and sheets. (NEDO)

  13. Elucidation of hydrogen mobility in tetralin under coal liquefaction conditions using a tritium tracer method. Effects of the addition of H2S and H2O; Tritium tracer ho wo mochiita sekitan ekika hanno jokenka deno tetralin no suiso idosei hyoka. Ryuka suiso oyobi mizu no tenka koka

    Energy Technology Data Exchange (ETDEWEB)

    Kanbe, M.; Saito, M.; Ishihara, A.; Kabe, T. [Tokyo University of Agriculture and Technology, Tokyo (Japan)

    1996-10-28

    It was previously reported that the tritium tracer method is useful for the quantitative consideration of hydrogen behavior in coal during coal liquefaction reaction. Tetralin is excellent hydrogen donating solvent, and is considered as one of the model compounds of coal. In this study, effects of H2S and H2O on the hydrogen exchange reaction between tetralin and gaseous hydrogen labeled by tritium were investigated. It was suggested that the conversion of tetralin and the hydrogen exchange reaction between gaseous hydrogen and tetralin proceed through the radical reaction mechanism with a tetralyl radical as an intermediate product. When H2S existed in this reaction, the hydrogen exchange yield increased drastically without changing the conversion yield. This suggested that the hydrogen exchange reaction proceeds even in the reaction where radical does not give any effect. In the case of H2O addition, the conversion yield and hydrogen exchange rate decreased into a half or one-third. It was suggested that H2O inhibited the formation process of tetralyl radical. 6 refs., 4 figs.

  14. Achievement report in fiscal 2000 on research and development project for immediately effective and innovative energy environment technologies. Development of new natural gas storage technology using adsorbents; 2000 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Kyuchaku zai wo mochiita shinkina ten'nen gasu chozo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation with natural gas which contributes to preserving the environment and reducing dependence on petroleum, research and development has been performed on a storage system using adsorbents that allows storage of natural gas at higher density than conventional systems. This paper summarizes the achievements in fiscal 2000. In material development, the current fiscal year has performed the discussions on synthesis of three dimensional complexes. An adsorbent was synthesized successfully that has adsorption performance 2.5 times greater than the secondary complex. In developing an improved activated carbon, an adsorbent was synthesized successfully that has methane adsorption performance four times greater than the compressed gas, by using monolithic activated carbon that uses no binders. Carbon briquettes were manufactured for the basic testing equipment for fuel storage container of natural gas fueled automobiles. In the system development, installation was completed on a bench scale equipment for a gas holder and BOG treatment system, whereas engineering data were acquired from the single-column type high pressure test and two-column type constituent separation and storage test using natural gas. Selection was carried out on applicable vehicle types for the adsorption storage system for natural gas fueled automobiles, and the basic design was made for fabrication of containers of different shapes. (NEDO)

  15. In situ observation of surface reactions with synchrotron radiation induced semiconductor processes by infrared reflection absorption spectroscopy using buried metal layer substrates; Umekomi kinzokuso kiban wo mochiita sekigai hansha kyushu supekutoruho ni yoru hoshako reiki handotai process hanno no sonoba kansatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshigoe, A.; Hirano, S. [The Graduate University for Advanced Studies, Yokohama (Japan); Mase, K.; Urisu, T. [Institute for Molecular Science, Aichi (Japan)

    1996-11-20

    It is known that infrared reflection absorption spectroscopy (IRAS) on semiconductor or insulator surfaces becomes practicable by using buried metal layer (BML) substrates, in which the metal thin film is buried order semiconductor or insulator films. In this work, IRAS has been measured for Langmuir-Blodgett films deposited on the BML substrate with SiO2/Al/Si(100) structure and the observed spectrum intensity has been quantitatively compared with the calculation assuming the ideal multilayer structure for the BML substrate. The BML-IRAS using CoSi2 has been adopted to the detection of SiHn on the Si (100) substrate during synchrotron radiation (SR) stimulated Si2H6 gas source molecular beam epitaxy. It has been found that SiH2 and SiH3 on the Si (100) surface are easily decomposed by SR, but SiH can`t be decomposed. From these experiments, it has been concluded that the BML-IRAS is an useful in situ observation technique for the photo-stimulated surface reactions. 26 refs., 9 figs.

  16. Theoretical study on instability mechanism of jet-induced sloshing. Model development using Orr-Sommerfeld equation generalized for non-parallel flow; Funryu reiki sloshing gensho no hassei kiko ni kansuru rironteki kenkyu. Hiheiko nagare ni ippankashita Orr-Sommerfeld hoteishiki wo mochiita model ka

    Energy Technology Data Exchange (ETDEWEB)

    Eguchi, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1998-07-25

    A theoretical model was developed to study the mechanism of free surface sloshing in a vessel induced by a steady vertical jet flow. In the model, jet deflection is calculated with eigen values of the generalized Orr-Sommerfeld equation which is applicable to slightly non-parallel jet. Instability criteria employed in the model are (1) resonace condition between sloshing and jet frequencies and (2) {pi} phase relation between jet displacement at an inlet and global jet deflection. Numerical results of the mathematical model have shown good agreement with experimental ones, which justifies that the inherent instability of free jet itself and edge tone feedback are the main causes of the self-excited sloshing. 9 refs., 10 figs.

  17. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium research and development of energy in its 2nd year (Research and development of eco-friendly material processing system using powder lubricant type releasing agent); 1999 nendo funtai rigata junkatsuzai wo mochiita sokeizai kako eko system no kenkyu kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of constructing a material processing industry consuming less energy, demanding less cost, and imposing less impact on the environment, research and development is conducted of an eco-friendly die-casting system which uses a powder lubricant type releasing agent. In the research, the effect of the die-casting metal cavity internal structure and the pressure pattern on the flowing behavior of the powder lubricant is made visible for analysis, and the mechanism of homogenous dispersion flow and injection is determined. In the research on powder type lubricants, efforts center on a calcium hydroxide-based powder lubricant, and studies are conducted about its adhesion to the metal die at high temperatures and the adhesion to and release from the metal die of molten aluminum, and the calcium hydroxide-based powder lubricant is found to work effectively. For the application of the powder lubricant to die-forging, a real forging system is experimentally built which includes a water-cooled die into which powder is injected with the die in the closed state. A powder lubricant type releasing agent GW-23 is tested for performance using this system, and then it is found that a powder lubricant prolongs the service life of dies and improves on working environments. (NEDO)

  18. FY 2000 report on the survey of the calculation of the overall conversion efficiency in case of using natural gas for fuel cells, etc.; 2000 nendo chosa hokokusho. Tennengas wo nenryodenchi ni mochiita baai no sogo henkan koritsu no santei ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of evaluating the efficiency of fuel cell including the fuel supply system, survey was made of drilling of gas resource, conversion to liquid base fuel, transportation, storage, etc., the energy conversion efficiency was studied considering reforming characteristics of various fuels. In the comparison between LNG, methanol, DME and GTL that originate in natural gas and LPG and naphtha that originate in oil, a big difference is that methanol, DME and GTL were made through the conversion process with the large energy consumption. Namely, by the time before the reforming into hydrogen, the oil base indicated a higher efficiency in secondary energy fuel production than the natural gas base. Further, the reforming efficiency is the highest in methanol and DME, and there is a little difference between the integrated fuel cell (normal pressure) and the hydrogen production use fuel cell (pressurized). Concerning city gas and GTL, the efficiency is lower, affected by S/C. The overall efficiency is determined considering the conversion efficiency in other stages since it is determined by the conversion efficiency of up to the raw fuel and the energy conversion efficiency at PEFC. (NEDO)

  19. Achievement report for fiscal 1998. Development of an industrial rinsing equipment of environmentally harmonizing type using an ultra critical fluid (the second year); 1998 nendo seika hokokusho. Chorinkai ryutai wo mochiita kankyo chowagata kogyo senjo sochi no kaihatsu (dai 2 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project is intended for environment friendly and pollution-free rinsing by using an ultra critical fluid of CO2 being an atmospheric constituent. It also has a purpose of establishing a new rinsing method implemented by an ultra precision component machine and device using such features possessed by the ultra critical fluid as high permeability and disinfecting activities. It is further intended of developing, fabricating, and practically using a rinsing equipment that makes possible precision rinsing of mechanical, electronic, optical and aeronautical components. Using the results of experiments performed in the previous year as the base, discussions were given on the relationship between the two aspects of the hardware aspect such as equipment configuration and piping of the rinsing equipment and the software aspect such as operating conditions and procedures and the rising effect. As a result, a new rinsing equipment of solvent circulation type was proposed. The basic design software for the specific equipment was completed, and an experimental equipment was designed and fabricated under the clean specifications. The performance evaluation and verification experiments were finished in the end of fiscal 1998, and collection of fundamental data has begun. With regard to the rinsing evaluation method, qualitative and quantitative analyses were performed on the rinsing by using a surface shape measuring microscope and the infrared spectroscopy. (NEDO)

  20. Report on technological achievements in fiscal 1999. Institutions for research and development of new environmental industry creating type technologies (Development of harmful substance reducing device for incineration furnaces using high-efficiency power pulse technology); 1999 nendo shinki kankyo sangyo soshutsugata kenkyu kaihatsu seido seika hokokusho. Kokoritsu pulse power gijutsu wo mochiita shokyakuroyo yugai busshitsu sakugen sochi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Development has been proceeded on a harmful substance (SOx, NOx, Dioxine, etc.) reducing device for incineration furnaces that can be installed retroactively to existing incineration facilities, using high-efficiency power pulse technology of energy saving type, and discharge in honeycomb ceramics. The developmental activities were advanced by dividing them into researches on (1) research of gas decomposing devices, (2) research of pulse plasma electric power source, and (3) research of SI thyristor for pulse. In the research (1), a pulse plasma experiment and a gas decomposing experiment were performed. In the former experiment, discussions were given on effects of discharge electrode structure on discharge in the honeycomb ceramics, wherein it was made clear that employing the mesh-comb type electrode structure can realize discharge along the ceramics surface. In the latter experiment, it was revealed that the simulated gas (dibenzofuran) can be decomposed to 90% by using a coaxial cylindrical reaction device. In the research (2), studies were performed on increasing voltage and current in the device, as well as on semiconductor driving circuits. In the research (3), studies were made on the high-quality gate zone forming method and the quality conduction zone forming method. (NEDO)

  1. Fiscal 1999 project for R and D of technology for immediately effective and innovative energy environment technology. Report on result of development concerning novel technology for natural gas storage using absorbent; 1999 nendo kyuchakuzai wo mochiita shinkina tennen gas chozo gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    R and D was conducted on a natural gas storage method using absorbent, a method having higher density compared with a conventional method in the form of liquefied or compressed natural gas, and the fiscal 1999 results were reported. In the development of materials, studies in the preceding year were continued on the synthesis of prospective organic metal complexes, with the selection and manufacturing of the materials carried out that were suitable for methane absorptive storage, for the use of bench-scale equipment for system development BOG treatment. In the development of the system, taking the need of gas holders and BOG treatment into consideration, the design of the bench-scale equipment was performed, as were the manufacturing and the installation of the equipment. In addition, with an absorptive storage simulation built, calculation under various conditions was found possible as well as calculation for the verification of concepts for the enhancement of performance. Furthermore, in the development of a fuel storage system for natural gas vehicles, studies were conducted on the reduction of weight of the fuel container, improvement in the freedom of a place for mounting the fuel container, grasp of needs of absorptive natural gas vehicles such as increase in the fuel storage, and analysis of application feasibility. (NEDO)

  2. Report on achievements in fiscal 1998. Research on acceleration of improving the base for biological resource information, and development of a technology to measure gene information (development of the DNA measuring technology using bead arrays); 1998 nendo seibutsu shigen joho kiban seibi kasokuka kenkyu idenshi joho no keisoku gijutsu no kaihatsu seika hokokusho. Bizu array wo mochiita DNA keisoku gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    It is necessary in the field of post-genoms to know statistical correlation between DNA orientation information and clinical data, which helped growth of DNA probe arrays (DNA chips). However, it is difficult in patent point of view to develop chips in Japan. On the other hand, a movement has begun to use beads fixed with DNA probes in place of DNA chips demarcated on the surface of solids. This is a method to investigate hybridized DNA by means of fluorescent detection, in which each bead retaining the DNA probes is colored to make identification of the retained probes possible, and hybridizing reaction is performed in aqueous solution. Hitachi has developed a DNA measuring technology using bead arrays. The bead array has probe fixing beads of about 100 {mu} m laid sequentially inside a capillary, wherein the array can be used to inspect a large number of genes. Thus, this method can be a DNA measuring technology which is inexpensive, and high in reproducibility. These features lead to a belief that the technology is suitable for gene inspection devices used in the process of medicine development and at the clinical sites. (NEDO)

  3. Study of reciprocating engine with Z mechanism. Part 1. Discussion of effect on the performances of new concept engine; Yodo shiten riron wo mochiita ofuku do engine ni kansuru kenkyu. 1. Shinkihon kozo no donyu ni yoru seino kojo no suisatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshizawa, Y; Fukuzaki, S; Kanno, M [Yoshiki Industrial Co. Ltd., Yamagata (Japan)

    1997-10-01

    A new reciprocating engine was developed as an application of new mechanism named as `Z mechanism.` In this new engine, the piston motion is described by a simple sine function and gives lower velocity around top dead center than that in conventional piston engines. Thus, the mode of combustion in this engine is closer to constant-volume process and gives higher thermal efficiency than ordinary engines. Use of Z-mechanism also eliminated high-order components of vibration that ordinary engines suffer. Development high-performance engine was successfully conducted with this new mechanism. 4 refs., 11 figs., 1 tab.

  4. Fiscal 2000 achievement report on the venture business assisting type regional consortium - Core industry creation type. Research and development of polisher robot system using intelligent force control; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Intelligent ryoku seigyo wo mochiita kenma robot system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The effort aims to automatize the manufacture of wooden furniture by robotizing the polishing work in the field of wooden furniture manufacturing, making use of the seeds provided by intelligent force control technologies. The intelligent force control technologies ('Delicate control of force for the open architecture type industrial robot' and 'Method for target orbit generation not requiring joystick teaching') of Saga University and the interior laboratory of Fukuoka Prefectural Industrial Research Institute are evolved and applied, and are integrated with the 3-dimensional object modelling technology developed by the mechanical and electronic laboratory, Fukuoka Prefectural Industrial Research Institute, and the CAD (computer aided design) data conversion technology developed by ASA Systems Inc. The result was a polisher robot system experimentally fabricated to satisfy the need of an automated polishing process in the wooden furniture manufacturing industry. The robot was tested, and achieved a surface coarseness level of 5{mu}m or less. As for the manufacturing rate, it attained a rate of approximately 100mm/s which was two times higher than the rate to be expected from a skilled worker. (NEDO)

  5. Fiscal 2000 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of practical application of integrated solid waste recycling technique using highly developed equipment for waste water; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Kokinoka kaishu mizushori system wo mochiita saishigen shori gijutsu no jitsuyoka ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The project aims to dry and pulverize into PDS (pulverized dry sludge) the waste (concrete sludge) discharged from ready-mixed concrete plants, and to develop its practical application. The fine sand component contained in the waste water after washing is removed to the maximum extent, and high-quality sludge-based PDS suitable for reuse is recovered. The process comprises an aggregate recovery stage, fine sand removing stage, coagulation/sedimentation stage, dewatering stage, crushing stage, drying stage, and a collection stage. High-quality PDS contains 30-40 mass% of CaO and 10-20 mass% of SiO{sub 2}, and its particles have an average diameter of 3-20{mu}m and an average specific surface area of 5,000-30,000cm{sup 2}/g. A particle is roundish with its angles rounded off. As for the fine sand component, not less than 90% thereof is removed by a wet cyclone method, and the water is collected and supplied for PDS manufacture. The development is already complete of powder and liquid coagulants, of which not less than 96% is inorganic, as coagulants exclusively for use for concrete. The quality of the manufactured PDS fulfills the target values, and it is concluded that PDS is recyclable like blast furnace slag or fly ash. (NEDO)

  6. Achievement report in fiscal 2000 on technical development to recycle waste building materials and glasses. Development of waste building material recycling technology (Research and development of wooden board manufacturing technology using demolished building lumbers); 2000 nendo kenchiku glass nado recycle gijutsu kaihatsu seika hokokusho. Kenhciku haizai recycle gijutsu kaihatsu (kenchiku kaitai mokuzai wo mochiita mokushitsu board seizo gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development has been made on a wooden board manufacturing technology re-utilizing demolished building lumbers and waste plastics with an intention of saving resources and reducing wastes. This paper summarizes the achievements in fiscal 2000. In developing the technology to re-use demolished building lumbers, a method for removing metals attached to demolished building lumbers was established by using a magnetic separator and a metal detector, with which it was verified that iron can be removed nearly 100%. With regard to waste plastics, simultaneous use of specific gravity separation utilizing centrifugal force and electrostatic separation provided a prospect that metals and plastics of high melting points can be removed from mixed resins in waste household electric appliances, and that polypropylene (PP), polystyrene (PS), and ABS can be classified at high accuracy. In manufacturing waste wood and waste plastic boards, pilot plants were built to use the 'melt spray method', 'melt blow method', and 'laminating method' as the means to spray molten resin onto wood raw materials, wherein trials were performed on mixing molten resins with wood flakes, and on board forming. (NEDO)

  7. Evaluation of dynamic properties of soft ground using an S-wave vibrator and seismic cones. Part 2. Vs change during the vibration; S ha vibrator oyobi seismic cone wo mochiita gen`ichi jiban no doteki bussei hyoka. 2. Kashinchu no Vs no henka

    Energy Technology Data Exchange (ETDEWEB)

    Inazaki, T [Public Works Research Institute, Tsukuba (Japan)

    1997-05-27

    With an objective to measure a behavior of the surface ground during a strong earthquake directly on the actual ground and make evaluation thereon, a proposal was made on an original location measuring and analyzing method using an S-wave vibrator and seismic cones. This system consists of an S-wave vibrator and a static cone penetrating machine, and different types of measuring cones. A large number of measuring cones are inserted initially in the object bed of the ground, and variation in the vibration generated by the vibrator is measured. This method can derive decrease in rigidity rate of the actual ground according to dynamic strain levels, or in other words, the dynamic nonlinearity. The strain levels can be controlled with a range from 10 {sup -5} to 10 {sup -3} by varying the distance from the S-wave vibrator. Furthermore, the decrease in the rigidity rate can be derived by measuring variations in the S-wave velocity by using the plank hammering method during the vibration. Field measurement is as easy as it can be completed in about half a day including preparatory works, and the data analysis is also simple. The method is superior in mobility and workability. 9 figs.

  8. FY 1998 results of the regional consortium R and D project/the venture promotion type regional consortium R and D (small-/medium-size venture creation type). 2nd year. Development of hazardous materials removal technology using high-functional zeolite; 1998 nendo kokinoka zeolite wo mochiita yugai busshitsu jokyo gijutsu no kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were carried out aiming at developing a device which removes/recovers freon substitutes and organic solvents discharged from semiconductor/pharmaceutical plans, using zeolite excellent in adsorption performance. In the R and D of high-functional zeolite, the design of materials is conducted by computer simulation, and effectiveness of the simulation was shown. In the development of zeolite honeycombs, the following were conducted: installation of honeycomb-form device, study of formation conditions, and fabrication of samples for adsorption/desorption tests. Moreover, the R and D were made on heater-monolithic zeolite, surface treatment of zeolite honeycomb, catalyst support, analysis, adsorption/desorption evaluation, micro-porous material cross-linking among clay layers, etc. As to the adsorption unit, the shape was so studied/designed that the gas containing NMP can efficiently keep in touch with zeolite honeycomb. Concerning the design of switching removal/recovery device, conducted were the design of a system which can be controlled at low cost, the development of adsorption/desorption operated software, etc. (NEDO)

  9. Report in fiscal 1999 on the achievements in research and development of the ITS technology using clean energy driven automobiles. Research and development of an efficient utilization system for car rentals in tourist resort areas; 1998 nendo clean energy jidosha wo mochiita ITS gijutsu no kenkyu kaihatsu seika hokokusho. Kankochiyo rentaka koritsuteki riyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the achievements in fiscal 1998 on developing ITS technology using clean energy driven automobiles. Development is intended on an efficient management and control method for EV car rentals in tourist resort areas using the ITS technology from the viewpoints of reducing road traffic load and global environment problems. The development items include a control center system, a system to control battery charging status at the center, a battery charging determination algorithm, and a car navigation and bi-directional communications mounting system. The system development has been completed nearly completely, having attained relatively high user satisfaction. However, because of the experimental rented cars having long mileage, there were few chances of verifying the charge determination algorithm and the functions of the ITS. Investigations were carried out on technological trends in overseas countries on EV and ITS, and on commuter car introduction projects. Structuring the hardware for a commuter EV system is not too difficult if the presently available EV and ITS technologies are used. However, in advancing commercialization, there are such assignments as establishment of software, operation patterns, and interfaces that enhance user convenience and profitability. (NEDO)

  10. Fiscal 2000 achievement report on the venture business assisting type regional consortium-Core industry creation type. Development of radiation detector utilizing surface reforming effect of irradiation; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Hoshasen shosha ni yoru hyomen kaishitsu koka wo mochiita hoshasen kenshutsuki no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    It has been clarified that the use of some kinds of semiconductor films, such as a rutile type titanium oxide film or a zirconium oxide film, results in a stable photocatalytic reaction in an intensive radioactivity region. In this effort, the effect is applied for the development of a FET (field effect transistor) type radiation detector capable of stable operation under high dose irradiation circumstances. Semiconductor materials such as a rutile type titanium oxide were subjected to irradiation tests on the ground, in which changes in their physical properties such as wettability or conductance were examined and the mechanism of surface reforming under irradiation was elucidated, and proper materials were selected. A prototype high radiation detector was fabricated that covers a 1mGy/hr-4kGy/hr region. For the establishment of a technology for growing spherical semiconductor crystals under microgravity, basic experiments were conducted using a free-fall facility at the Japan Microgravity Center. Basic experiments were conducted for the fabrication of a prototype radiation detector to operate in a high radiation region from 0.1kGy/hr to 2kGy/hr and beyond, and a prototype spherical semiconductor radiation detector was fabricated. Achievements of the effort are mentioned above. (NEDO)

  11. Road drainage system using highly compressible and long-term permeable geotextile. Evaluation of long-term permeability and application to trafficability in a tunnel; Kotaiatsu mezumari taikyugata geotextile haisuizai wo mochiita roban haisui taisaku. Mezumari taikyusei no hyoka to tunnel konai kasetsu doro no trafficability kaizen koka

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, S.; Yamagishi, K.; Hirama, K.; Ueno, T. [Obayashi Corp., Tokyo (Japan)

    1998-07-10

    A geotextile drainage material called ART-DRAIN has been developed. It was applied to temporary roads in a tunnel, to evaluate its permeability through a long-term permeability test using a model. The ART-DRAIN is a drainage material for protecting the roads from muddy conditions in a tunnel due to spring water. A filter for permeating fine soil particles was employed to keep the permeability. From the long-term permeability test using a model, appropriate permeability of ART-DRAIN was maintained for three years without blinding. There was only a slight inflow of fine grain soils into the ART-DRAIN. It was confirmed that the permeability was not obstructed by the fine grain soils. The ART-DRAIN was applied to tunnel construction works for the high-speed railway in Kyoto and the national road in mountains. From these applications, factors for enhancing the permeability effect were confirmed, which includes the selection of high quality muck, insurance of the road-bed strength by the initial compaction, use of road drainage materials with high compressible property and permeability of filter, and intervals of drainage. 1 ref., 19 figs., 1 tab.

  12. Features and performance of PCa board which cuts off the electromagnetic wave. Electromagnetic shield building using the carbon fiber contamination PCa board; Denjiha wo shadansuru PCa ban no tokucho to seino. Tanso sen'i konnyu PCa ban wo mochiita denji shirudobiru

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Katsuo; Kasai, Yasuaki [Obayashi Corp., Osaka (Japan); Okada, Shin' ichiro; Sakamoto, Shin [Osaka Gas Corp., Osaka (Japan)

    1999-03-10

    With the rapid popularization of public radio information communication equipment, portable telephones, wireless LAN, etc., the interception (building shield) of the electromagnetic wave internal and external the building becomes large problem. As process equal to the convention and the method in which the cost is possible, they did do not shield the whole building, and also ensure the comfort as an office, and PCa board which mixed the carbon fiber into the mortar was developed. They described the survey result of the electromagnetic shield performance of the building which constructed by using this in external wall. They explained electromagnetism characteristics of the contamination mortar and application to the PCa board and method. They carried out the measurement in the electromagnetic shield room laboratory, and they obtained next result. 1) There is seldom on the effect both only the concrete and only by the carbon fiber mesh. 2) They considered the effect that carbon fiber chop 1% are mixed into the concrete. 3) The effect became a maximum, when carbon fiber chop and carbon fiber mesh were mixed, and they confirmed being excellent cost-concerned. (NEDO)

  13. FY 2000 report on the results of the new regional consortium R and D project - Immediately effective type new regional consortium R and D. Study of the developmental technology for high-density recording materials using inverter plasma; 2000 nendo chiiki shinsei konsosiamu kenkyu kaihatsu jigyo - Sokkogata chiiki shinsei konsosiamu. Inbata purazuma wo mochiita komitsudo kiroku zairyo kaihatsu gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of reducing the price and size of large-capacity hard disk drive (HDD), using inverter plasma technology, developmental study was conducted of production technology of substrate for HDD using blue sheet glass as a main material and film formation technology in the media for HDD, and the FY 2000 results were reported. In the development of low-cost glass substrate, formation technology of the barrier layer to block the elution of alkali component was developed for blue sheet glass substrate. As to the development of formation technology of low-cost recording layer, developmental study was made of technology of formation of the layer as undercoat of magnetic recording layer onto the barrier layer. As a result of the experiment, the following were confirmed: metal chromium is well fit for the barrier layer and can be a proposed material of undercoat; it is possible to construct the magnetic media layer on the glass substrate. Concerning the development of the inverter plasma film formation unit, a unit was developed where it is possible to form the film of blue sheet glass substrate with a size of 3.5 inches. (NEDO)

  14. Improvement of the efficiency characteristics on the photovoltaic generation system based on a generation control circuit. Part 3. Research on architectural systematization of energy conversion devices; Dosaten seigyo kairo wo mochiita taiyo denchi hatsuden koritsu no kaizen. 3. Energy henkan no kenchiku system ka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, T.; Ito, N.; Kimura, G.; Fukao, S.; Sunaga, N.; Tsunoda, M.; Muro, K. [Tokyo Metropolitan University, Tokyo (Japan)

    1996-10-27

    In introducing a photovoltaic power generation system to urban homes, the general practice is to install a large number of solar cell panels on the roof. However, as is often the case, a part of the solar cell panels is in the shadows (partial shadows) of neighboring homes, electric poles, cables and trees. Under the circumstances, studies were made on the numerous changes in the lowered generating capacity of individual solar cells by the partial shadows. Developed by the authors were the generation point control principle, in which the generation point was individually controlled on serially connected plural solar cell modules, and a practical circuit system based on that principle with the effects verified in a field test. In the test, the generated power of the system was 476W without partial shadows, and was 323W with partial shadows and without the operation of the generation point control circuit, increasing to 406W with partial shadows and with the operation of the circuit. As a result, compared with the case where no generation point control circuit was employed, the effectiveness of the proposed circuit was evident. 3 refs., 10 figs., 1 tab.

  15. Fiscal 1999 achievement report. Venture seed pickup type international cooperative research project (Development of multi-beam semiconductor laser-aided preparation system for photogravure printing using water-based ink); 1999 nendo venture seeds hakkutsugata kokusai kyodo kenkyu jigyo seika hokokusho - venture seeds No.8. Suisei ink wo mochiita gurabia (oban) insatsuyo multi beam handotai laser seihan system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the prevention of environmental contamination due to oil-based ink used in the photogravure printing process, efforts were exerted to develop a technique of laser-aided photogravure printing using a water-based ink. It was learned that the laser optical system technology of CR Corporation of Canada was practical and high in quality, and a delay occurred in the development of an evaporation type resin for use under this project. Then the initially planned design was abandoned for a type using a new optical system manufactured by CR Corporation. In the development of plate making materials, it was found that resin evaporation was incomplete in a 1-layer structure design. A 2-layer structure design was then employed instead, and the evaporation goal was achieved. Now that the optical system was changed, the resin was also replaced with a thermosensitive type, which enhanced work efficiency. The CR Corporation-manufactured laser optical system was installed on a mount, the processor system was controlled and adjusted, and a printing test was conducted using a water-based ink of German make. It was found that the product of the new system was higher in quality than that printed by the conventional mechanical perforation type printer using an oil-based ink. (NEDO)

  16. Achievement report for fiscal 1998 on area consortium research and development business, 1st year. Area consortium energy research and development (molding material processing eco-system using powder lubricant); 1998 nendo chiiki consortium energy kenkyu kaihatsu bun'ya. Funtai rikei junkatsuzai wo mochiita sokeizai kako eko system no kenkyu kaihatsu (dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A material processing technology demanding but low energy and cost and causing low environmental impact was developed using a powder lubricant in a closed metal die system. An inorganic powder excellent in adhesiveness as lubricant was discovered. Powder lubricants for die casting and new carbon lubricants for metal die forging were also developed. In a test in an eco-die casting system, it was found that power was better than water solution in terms of finish and energy efficiency. In the development of a metal forging system using a powder lubricant, existing graphite lubricants and new powder lubricants containing fullerene were subjected to evaluation (ring tests). Two types of graphite solutions now in use and two powder lubricants were evaluated by the ring tests, and this enabled the comprehension of powder lubricant characteristics. For the development of a die casting system requiring no lubricant, a metal die surface treatment method was found that produces a surface excellent in resisting erosion by the application of the aluminizing ion nitriding composite treatment method. In addition, wettability was compared between a PVD (physical vapor deposition)-formed nitride film and the powder lubricant constituents. The report also refers to surveys conducted for commercialization. (NEDO)

  17. Study on transmitting mechanisms for CVT using a dry hybrid belt. Numerical simulation of transmitting forces and pulley thrusts at steady and transitional states; Kanshiki fukugo belt wo mochiita CVT ni kansuru kenkyu. Teijo oyobi hensokuji ni okeru dentatsuryoku to pulley suiryoku no suchi simulation

    Energy Technology Data Exchange (ETDEWEB)

    Miyazawa, T; Kuwabara, S; Fujii, T [Doshisha University, Kyoto (Japan); Nonaka, K [Bando Chemical Industries, Ltd., Kobe (Japan)

    1997-10-01

    A numerical model was developed to analyze the power transmitting mechanisms for CVT (Continuous Variable Transmissions) using a dry hybrid belt. The model consists of linear springs representing the rigidities of blocks, rubber and cord, and interface elements which identify slippage between pulleys and blocks. By using the present model, forces acting on the belt were calculated not only at steady but also transitional states. Calculated results well coincide with experimental ones. It is revealed that there is a great change of the pulley thrust when the speed ratio is shifting. Little radial slippage occurs when the pulley groove is reduced. 1 ref., 9 figs.

  18. Study on a metal pushing V-belt type CVT. Numerical analysis for belt tension distribution in brands of a ring at steady state; Kinzoku V belt wo mochiita CVT ni kansuru kenkyu. Sekiso belt (steel ring) no dendo kiko kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, T; Kuwabara, S [Doshisha University, Kyoto (Japan); Kanehara, S [Honda Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    The power transmitting mechanisms for laminated belts were studied to analyze belt tension in each band of the ring of metal V-belts. A numerical model consisting of linear springs and frictional elements was proposed. The present model was experimentally proved. It is revealed based on the numerical results that each band shares the ring tension equally when the coefficients of friction for bands and a pulley are the same while the first band must support more when the coefficients of friction between two bands are lower than that between a saddle surface of the block and the inner band. 4 refs., 9 figs.

  19. FY 1998 results of the regional consortium R and D project/the venture promotion type regional consortium R and D (small-/medium-size venture creation type). Development of a new X-ray wavelength-modulated diffraction system; 1998 nendo hacho henco kaisetsuho wo mochiita shin x sen kaisetsu hochi no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the wavelength-modulated X-ray diffraction method, noting that synchrotron radiation (SR) is a high luminance white light with the continuous wavelength distribution, the Blagg refection from crystals is recorded by continuously changing the wavelength. The paper described the results of the development. The camera distance/diameter were made variable in connection with the wavelength modulation. By expanding the area (enlargement of screen) of imaging plate (IP) by Weissenberg camera method, the number of diffraction dots increased, and the data on wavelength gradient were made exact. The camera was completed as designed by introducing X-ray beams, adjusting collimator, specimens, and position of IP. The concentrating mirror device is integrated into the beam line of the SR center, and mirror effects were confirmed through the actual synchrotron radiation. The function of wavelength modulation of double crystal spectrometer was also confirmed. Two kinds of ferrocene derivatives were synthesized of which the wavelength modulation effect is expected as specimen for functional test. Monocrystals were successfully raised, and measured by wavelength-modulated X-ray diffraction device. The validity of phase determination function of the developmental device was confirmed with the results of the existing structure analysis as reference. (NEDO)

  20. Study on internal flow near the impeller outlet of a winnowing fan. 2nd Report. Discussion of a impeller with forward-inclined blades by computational fluid dynamics; Karami fan no haneguruma deguchibu kinbo no nagare ni kansuru kenkyu. 2. CFD wo mochiita maemuki hane ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kawase, M. [Tokushima University, Tokushima (Japan); Fukutomi, J.; Nakase, Y. [Tokushima University, Tokushima (Japan). Faculty of Engineering

    2000-03-25

    Because of a strong 3-dimensional flow, it is difficult to produce a uniform flow or improve efficiency with winnowing fans. Through experiments with various types of impellers, it was found in an earlier study that a forward-inclined impeller could produce a uniform flow and improve efficiency. It was ten reported in a subsequent study aimed at identifying the mechanism behind this, in which the relationship between velocity and static pressure in an impeller of small inclination angle was examined from the perspective of flow, that flow analysis was effective towards estimating inconsistent flow characteristics. Based on these findings, this project was designed to measure and analyze flow characteristics in a forward-inclined impeller. It was found that forward-inclined impellers have many regions of circulating flow and that the mainstream which moves to the outlet is narrow in effective area. As a result, velocity increases and discharge blow rapidly expands within a short distance. Therefore, good static pressure recovery is obtained. (author)

  1. Study on reinforced concrete high-rise building using prefabricated beam-column joints. Part 3. ; Basic anchorage behaviors of longitudinal bars of beams. Hahsirater dot hari setsugobu PC ka koho (PG connection koho) wo mochiita RC koso tatemono no kaihatsu. 3. ; Hari shukin no kisoteki teichaku seijo

    Energy Technology Data Exchange (ETDEWEB)

    SEkine, M.; Yoshioka, K.; Eto, H. (Obayashi Corp., Tokyo (Japan))

    1991-08-10

    Pull-out tests were carried out to examine basic anchorage behaviors of through holes for beam re-bars by using a PG connection method, in which columns and beam-column joints with through holes for beam re-bars in the reinforced concrete framed construction are precast simultaneously. Specimens made by the PG connection method showed better anchorage behaviors than specimens made by the conventional anchorage method. In case of anchorage width of 80cm and concrete strength of about 350kgf/cm{sup 2}, it was recognized that large slipping of re-bars did not occur under allowable bond stress when the interval between re-bars was not less than 15cm and covering depth to the core of re-bars was not less than 8cm. Concerning a specimen which did not show splitting bond failure because of lateral compressive stress, bond stress of re-bars when large slipping occurred was 1.5 times or more in comparison with the allowable bond stress. Since this specimen held high slipping rigidity even after increase of slipping, its anchoring stress increased by 32-57% compared with a specimen without lateral compressive stress. 4 refs., 7 figs., 3 tabs.

  2. Construction method with prestressed connection of precast prestressed concrete using composite slab with multi-round opening web. Bibai factory office building of Dopi Kensetsu Kogyo Co; Web bu ni renzoku enkei kaiko wo yusuru PC gosei yukaita wo mochiita PC kumitate koho. Dopi kensetsu kogyo (kabu) Bibai kojo jimushoto shinchiku koji

    Energy Technology Data Exchange (ETDEWEB)

    Kuramochi, H.; Nakai, J.; Arai, S.; Toriya, T.

    1997-07-31

    This report summarizes the experimental result on the structural performance of precast prestressed concrete (PC) composite slab work, and a construction method with prestressed connection of PC. Although a double T type precast PC slab (DT board) is frequently used as buried form for slabs, it requires extremely complex bar arrangement and complicated works. The reinforcement method of supports using deformed hair pin type bars was thus devised which has a structural performance higher than that of the previous methods as well as simple bar arrangement and superior workability. For the reinforced DT board (DP slab) and the composite slab construction method using the DP slab, the structural safety and retained use environment were confirmed by structural performance test and construction test. The foundation and footing beam of the Bibai factory office building were constructed by the conventional method considering the construction method, while the column, beam and floor by this method using PCa members. The upper building frame was thus completed for as short as 23 days. 5 refs., 15 figs., 4 tabs.

  3. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium on energy research in its 3rd year (Development of an environmentally-friendly industrial cleaning system using supercritical CO2 fluid); 1999 nendo chorinkai ryutai wo mochiita kankyo chowagata kogyo senjo sochi no kaihatsu seika hokokusho. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In high-technology industries such as the semiconductor industry, cleaning operations are indispensable. In these industries, replacement of the current method with a new one has become an urgent matter, thanks to the new control imposed on pollutant CFC (chlorofluorocarbon). Using a supercritical fluid, whose density and other features may be regulated extensively and continuously by controlling temperature and pressure, various conditions may be set in detail for the cleaning element, such as the dissolving power, dispersion force, surface activity, and chemical reactivity. The fluid is environmentally friendly and free of pollution. Facilities for recovering, regenerating, and circulating the solvent are incorporated into a test cleaner built in the preceding fiscal year, and a new system is completed. The system is operated in a test run for performance assessment, and data are collected to specify cleaning conditions best for each kind of the target items. Studies are made to expand the scope of system application for use under supercritical conditions. An experiment is conducted using a pollutant model, and a method to analyze the degree of cleaning is studied using an effective diffusion coefficient. A self-cleaning method is studied for the filter for the regeneration of the supercritical cleaning solvent. A market research is carried out for the commercialization of the industrial cleaning system. (NEDO)

  4. Preparation of spherical fine particulate pigments within water-in-oil emulsions and their properties. (II). ; Formation mechanism and characteristic of spherical fine particulate pigment of tartrazine. W/O emulsion wo mochiita kyujo biryushi ganryo no chosei to seishitsu(dai 2 ho). ; Kiiro 4 go kyujo biryushi ganryo no seisei kiko to tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Imai, T.; Iwano, K.; Hotta, H.; Takano, S.; Tsutsumi, H. (Kao Corporation, Tokyo (Japan))

    1991-12-20

    The previous report explained that an excellent spherical particulate pigment with a grain size of 0.5 mm or less can be obtained by preparing multinuclear aluminum lakes from acidic dyes and multinuclear aluminum salt using water droplets in a W/O emulsion as reaction fields. This paper describes preparing pigments varying the charging concentrations of the pigments in a W/O emulsion and the droplet particle size to discuss the mechanism of forming the pigments. As a result, it was found that the particle sizes in the produced pigments have a clear correlation with the charging concentrations of the pigments and the droplet particle sizes in the W/O emulsion. A pigment produced in the W/O emulsion forms only in its own droplets, and reflects its particle sizes. Films dispersed with pigments having different particle sizes were prepared to discuss their tinting abilities, whereas it was clarified that the smaller the particle size, the higher the tinting ability and the higher saturation in colored paint films. 6 refs., 9 figs., 3 tabs.

  5. Report on research results of the FY 2000 medical/engineering cooperative research project. Fundamental research on microelectrode-aided gene information measurement system (Research and development of gene diagnostic system using superhigh-sensitivity microelectrode DNA chip ECA - electrochemical array); 2000 nendo igaku kogaku renkeigata kenkyu jigyo kenkyu seika hokokusho. Bisho denkyoku riyo idenshi joho keisoku system ni kansuru kiban kenkyu (chokokandogata bisho denkyoku DNA chip ECA (denki kagaku allay) wo mochiita idenshi shindan system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The fundamental research is conducted for developing the microelectrode on which a synthetic oligonucletide probe is immobilized, and for establishing the system capable of detecting the hybrid formation simply and quickly, in order to develop the advanced DNA chips for diagnosis. The project results include development of the prototype array electrode with 25 1mm-diameter gold electrodes uniformly arranged at intervals of 4.5mm; development of the electrochemical activity analyzer for multi-electrode systems, showing the performance almost on a level with that of the existing electrochemical analyzer for the single-electrode systems; establishment of the gene databases; development of the method which can produce a sufficient quantity of nucleic acid for DNA chip analysis by studying the method of preparing the nucleic acid from the blood serum, preparing RNA from a trace quantity of the living liver sample and amplifying the genes, wherein the nucleic acid is produced while its profile before the amplification is kept intact; and establishment of the method for detecting the hepatitis B virus by combining the electrochemical detection of DNA by a non-immobilized probe with the PCR method. (NEDO)

  6. FY 2001 report on the results of the survey of the environmentally friendly type energy community project. Feasibility survey of the commercialization of the gasification melting system use heat supply business using container packing waste plastic and other waste as raw materials; 2001 nendo kankyo chowa gata energy komyuniti jigyo. Gaska yoyu system wo mochiita yoki hoso kei hai purasuchikku oyobi sonota no haikibutsu wo genryo to suru netsu kyokyu jigyo no jigyoka F/S chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    As to gasification melting facilities (Eco-Ene center) using container packing waste plastic and other waste as raw materials in 'the Eco-town Kochi City - Business Project,' study/evaluation of environmental conservation and business profitability were conducted. In Eco-Ene Center, power generation (power supply to users: 1,295 kW) and heat supply (27 GJ/h at maximum) are conducted using the gas product obtained from the combustion of waste. The environmental effect of introduction of Eco-Ene Center is as follows: energy conservation: 51,350-113,594 GJ/y, environmental pollution gas reduction: 1,128-4,987 t-CO2, 1,441-6,691 kg-NOx, 2,965-6,447 kg-SOx, 27,309 {mu}g-TEQ/m{sup 3} dioxin. As a result of the study of economical efficiency, the following was found out: In securing the ending cash balance such as personnel expenses, land lease cost and transportation cost, the subject is the acceptance price of container packing plastic from which a half of the profit can get, and it is necessary to receive subsidy for 1/2 of the price and reduce operating expenses. (NEDO)

  7. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. First year report. Development of the process for creation of new functional materials using electron beam excited plasma; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Denshi beam reiki plasma wo mochiita shinkino zairyo sosei process no kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The development of manufacturing technology was proceeded with for a high speed nitriding system using electron beam excited plasma device which realizes high dissociation for nitrogen molecules and controls the plasma state. By the device, the following are aimed at: high quality/high speed nitriding, formation of super-hard cubic system boron nitride (c-BN) and carbon nitride (CN) films on the surface of tools, and formation of TiO{sub 2} thin films with high infrared reflectance and environmental purification photocatalyst function. TiO{sub 2} thin films are assumed to be applied to window glass by making use of the high performance heat mirror function as well as the environmental purification function. Studies were made in the following 6 fields: 1)development of small electron beam excitation plasma source; 2) development of high speed nitrided container; 3) establishment of technology for real-time monitoring of radicals and ions; 4) design/trial manufacture of a device to form super-hard nitrided thin films; 5) development of heat mirror film formation device; 6) establishment of a method to evaluate effects of photocatalyst. (NEDO)

  8. FY 1998 annual report on the development of laser-aided, noncontacting, realtime, in-process dressing method using a grinding stone with ultrafine abrasive grains, and study on techniques for applying the method to grinding stone of superthin blades; 1998 nendo laser wo mochiita choteiryu toishi no hisesshoku real time inprocess dressing ho no kaihatsu oyobi gokuusuha toishi eno tekiyo gijutsu ni kansuru kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A new noncontacting dressing method using a laser as a tool has been studied and developed, in order to develop environment-compatible, energy-saving type machining machines. In this study, a cup-shaped grinding stone is developed for grinding performance testing by micron-order diamond abrasive powder, used for producing a grinding stone of superthin blades, is mixed with a cast iron binder, molded and sintered. In the grinding performance test, zirconia as a work is ground at a constant pressure to the grinding stone working surface before and after the laser-aided dressing, to analyze grinding/removal efficiency and grinding resistance. The grinding stone working surface conditions are observed by a scanning electron microscope after the laser-aided dressing, to correlate the surface conditions with the grinding data. It is found that the laser-aided dressing method needs no lubricant, is clean, cutting grinding time when incorporated in the machining process, suitable for grinding stone of low stiffness and ultrathin blades by use of ultrafine abrasive grains, suffering no exfoliation of the diamond grains, and hence economical. (NEDO)

  9. FY 1998 report on the results of the R and D of ITS technology using clean energy vehicles. R and D of the urban/residential area joint utilization system and advanced travel management/information supply; 1998 nendo clean energy jidosha wo mochiita ITS gijutsu no kenkyu kaihatsu. Toshinbu oyobi jutakuchi kyodo riyo system narabi ni soko kanri joho teikyo no kodoka no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The purpose of the project in FY 1998 is 'Experimental verification for EV spread promotion.' Two of a 3-month experiment were conducted in Yokohama MM21 area (Yokohama, Kanagawa) and in Tama Newtown (Inage, Tokyo) using a total of 100 (50 each) small EVs. The development was aimed at of an urban type rental-car system in Yokohama and of a car-sharing type second-car system for residential in Inage. As to these responses to ITS technology, the basic vehicle operation system was made common in both areas, and the daily use system was made a regional system considered of purposes of use, regional characteristics, etc. The experimental verification was worked on as almost expected in terms of the vehicle management, monitor assessment, responses from persons concerned in both areas. Therefore, it is said that the R and D have almost reached a point where there can be seen a possibility of system commercialization. Through the experimental verification, the development was able to be smoothly promoted of the basic technology and element technology which are thought to be needed for the commercialization of EV. From the experience of this experimental verification, it is judged that it is desirable to tackle the commercialization by a membership system when the commercialization of EV joint use system is planned in future. (NEDO)

  10. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. Third year report. R and D of a working material processing eco system using powder mold-releasing lubricant; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Funtai rigata junkatsuzai wo mochiita sokeizai kako eco system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of constructing the industry of processing low cost/low environmental load working materials, the development was proceeded with of a block die type powder mold-releasing system. Studies were made in the following 6 fields: 1) optimization/commercialization of new adhesion/flow methods; 2) optimization/commercialization of new powder mold-releasing lubricant; 3) demonstrative experiment and optimization of an eco die cast system; 4) optimization of a powder mold-releasing forging system; 5) application test on the actual mold-releasing lubricant reduction type system; 6) comprehensive investigational study. In 1), studied were a method to integrate the profile of supply pressure of powder conveying air flow and the basic information on adhesion behavior into the practical process, and optimization of powder supply method and supply device control sequence. In 2), the development was made of a sleeve use high thermal insulation type powder mold-releasing lubricant (composed mostly of Al(OH){sub 3}, graphite and wax). This powder mold-releasing lubricant remarkably improved forging ability of the ultra-thin material with 0.4mm thickness and materials with complex shapes and markedly decreased fracture chills. (NEDO)

  11. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / Development of an environmentally friendly industrial cleaning system using near-critical and supercritical carbon dioxide (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / chorinkai ryutai wo mochiita kankyo chowagata kogyo senjo sochi no kaihatsu (daiichi nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In the manufacturing process of semiconductors and in the high tech industry, cleaning is indispensable. At present, when regulation of the use of CFC which used to be much used has been decided on, the conversion to the use of substitutes for CFC cleaning is urgently needed. Transfer to cleaning by water/alcohol/hydrocarbon has been proceeded with, but there are a lot of problems. Out of the development of the cleaning method using supercritical fluid, the paper described the fiscal 1997 result. As to enhancement of efficiency and decrease in size of equipment, a cleaning experiment by high pressure CO2 around the critical point was conducted by integrating nozzle, ultrasonic generator and cavitation generator and adding solvent circulating system. Multi-purpose and energy saving of the equipment were also studied. To establish an analysis method for the cleaning degree, the contaminated component film of trace organic matter with a specified thickness was formed on the silicon wafer, and using the Fourier transform ultrared spectroscopy, a method to determine the film thickness was studied. For the function evaluation for precision machine parts and determination of optimum cleaning conditions, the cleaning/degreasing process of valves were compared with the conventional method. For the product manufacturing, the paper investigated and prepared the data in Japan and from abroad. 55 refs., 79 figs., 18 tabs.

  12. Report on diagnosis and survey on research cooperation in the research cooperation promotion project in fiscal 1994. Research cooperation on manufacturing clean fuel for consumer use from gasified coal gas / Research cooperation on a method for pulp manufacturing of low-pollution and energy saving type by using non-wood raw materials; 1994 nendo kenkyu kyoryoku suishin jigyo 'kenkyu kyoryoku shindan chosa' hokokusho. Sekitan gas ka gas kara no minseiyo clean nenryo seizo ni kansuru kenkyu kyoryoku / himokuzaikei genryo wo mochiita teikogai shoenegata pulp seizoho ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    In solving the problems in developing technologies peculiar to developing countries, Japan will provide cooperation. This paper describes the achievements in diagnosis and survey in fiscal 1994. Development will be made on a manufacturing process for dimethylether (DME), a synthesizable and portable clean fuel, by using coal produced in China. Annual DME production of 10,000 tons will make it possible to supply 50,000 households with the fuel of one year consumption, whereas return on the construction investment and profit can be expected. At the Shanxi Coal Chemistry Research Institute, a 500 tons a year plant making DME from gasified coal gas is scheduled to begin operation. Development will be made on a pulp manufacturing technology in China, in which environmental pollution due to waste water is largely reduced, and operation cost is reduced. Application of the oxygen-alkaline evaporation and decomposition process developed in Japan will be considered, which uses non-wood raw material such as rice straw, wheat straw and megass). The raw materials are immersed continually in low-concentration alkaline solution, dehydrated, and then lignin is oxidized and decomposed by using oxygen in a continuous oxidation reactor to make the material into pulp. China uses non-wood materials as paper raw materials at 80%, whereas effects are expected in waste water pollution prevention, energy saving, resource saving and economics. (NEDO)

  13. Report on the results of the FY 1999 R and D of the medical welfare equipment technology and the development of an implantable total artificial heart system using a non-pulsatile pump. R and D of an implantable total artificial heart system using a non-pulsatile pump (R and D of the functional/cure artificial heart); Iryo fukushi kiki gijutsu no kenkyu kaihatsu tainai umekomigata jinko shinzo system 1999 nendo seika hokokusho. 5. Renzokuryu pump wo mochiita tainai umekomigata jinko shinzo system no kenkyu kaihatsu (kinoteki chiryoteki jinko shinzo no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    The R and D of element technology were made on non-pulsatile pump, drive/controller, energy supply storage system, structural coating materials, etc., and the prescribed target was achieved. In the R and D of a total system, a blood-removing conduit with movability was designed to avoid the functional inlet obstruction, and the animal experiment was carried out. In the short-term chronic animal experiment on the implantation of a single bypass model using this artificial conduit and in the animal experiment for implantation of functional/cure artificial heart, it was confirmed that the operation was conducted easily, the flow rate of the blood of the artificial heart is extremely stable, and the blood-removing conduit functions favorably. In the R and D on Tele-TAH with the aim of future home medical treatment, it became possible to acquire via monitor the pump drive information and blood circulation state information on the animals tested in the breeding farm. The remote medical simulation was made. (NEDO)

  14. FY 1999 Report on the results of technological development of machine tools for rationalization of energy utilization. Development of a lathe with high precision and conservation of energy using natural phenomenon (Thermal countermeasure using self compulsory cooling and thermal insensitive structure - results of the first year); 1999 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Shizen gensho wo takumi ni oyoshita sho energy koseido senban no kaihatsu (self kyosei reikyaku to netsufukan gijutsu wo mochiita netsuhenkei yokusei taisaku - dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A lathe, which is a central tool in a factory of automobiles or home electric appliances, tends to suffer decreased machining precision resulting from thermal deformation. This project is aimed at development of the energy-saving, high-precision lathe technologies using self compulsory cooling and thermal insensitive technologies as the countermeasures against the thermal deformation. The self compulsory cooling is a method of cooling by evaporation of water with an evaporative, water-absorptive cloth being bonded to a machine tool surface around the major axis. The thermal insensitive technologies include the three-dimensionally zero-center design technologies which help design a lathe in such a way to set the processing point (tool working point) at the base of thermal deformation in the X, Y and Z axis directions; material combination technologies to control thermal deformation; and coloring technologies to control thermal deformation. The development target is the high-precision lathe fabrication technologies, which realize a temporal precision change of 1 to 2 {mu}m or less per work dimension of 100mm. The activities cover 5 areas, including development of elementary technologies for each item and construction/evaluation of the full-size test unit. (NEDO)