WorldWideScience

Sample records for mobilisation technique applied

  1. Cervical spine mobilisation forces applied by physiotherapy students.

    Science.gov (United States)

    Snodgrass, Suzanne J; Rivett, Darren A; Robertson, Val J; Stojanovski, Elizabeth

    2010-06-01

    Postero-anterior (PA) mobilisation is commonly used in cervical spine treatment and included in physiotherapy curricula. The manual forces that students apply while learning cervical mobilisation are not known. Quantifying these forces informs the development of strategies for learning to apply cervical mobilisation effectively and safely. This study describes the mechanical properties of cervical PA mobilisation techniques applied by students, and investigates factors associated with force application. Physiotherapy students (n=120) mobilised one of 32 asymptomatic subjects. Students applied Grades I to IV central and unilateral PA mobilisation to C2 and C7 of one asymptomatic subject. Manual forces were measured in three directions using an instrumented treatment table. Spinal stiffness of mobilised subjects was measured at C2 and C7 using a device that applied a standard oscillating force while measuring this force and its concurrent displacement. Analysis of variance was used to determine differences between techniques and grades, intraclass correlation coefficients (ICC) were used to calculate the inter- and intrastudent repeatability of forces, and linear regression was used to determine the associations between applied forces and characteristics of students and mobilised subjects. Mobilisation forces increased from Grades I to IV (highest mean peak force, Grade IV C7 central PA technique: 63.7N). Interstudent reliability was poor [ICC(2,1)=0.23, 95% confidence interval (CI) 0.14 to 0.43], but intrastudent repeatability of forces was somewhat better (0.83, 95% CI 0.81 to 0.86). Higher applied force was associated with greater C7 stiffness, increased frequency of thumb pain, male gender of the student or mobilised subject, and a student being earlier in their learning process. Lower forces were associated with greater C2 stiffness. This study describes the cervical mobilisation forces applied by students, and the characteristics of the student and mobilised

  2. Hypoalgesic effect of a passive accessory mobilisation technique in patients with lateral ankle pain.

    Science.gov (United States)

    Yeo, Hwee Koon; Wright, Anthony

    2011-08-01

    A randomised, double blind, repeated measures study was conducted to investigate the initial effects of an accessory mobilisation technique applied to the ankle joint in 13 patients with a unilateral sub-acute ankle supination injury. Ankle dorsiflexion range of motion, pressure pain threshold, visual analogue scale rating of pain during functional activity and ankle functional scores were assessed before and after application of treatment, manual contact control and no contact control conditions. There were significant improvements in ankle dorsiflexion range of motion (p = 0.000) and pressure pain threshold (p = 0.000) during the treatment condition. However no significant effects were observed for the other measures. These findings demonstrate that mobilisation of the ankle joint can produce an initial hypoalgesic effect and an improvement in ankle dorsiflexion range of motion. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

  3. Developing a Knowledge Network for Applied Education Research to Mobilise Evidence in and for Educational Practice

    Science.gov (United States)

    Campbell, Carol; Pollock, Katina; Briscoe, Patricia; Carr-Harris, Shasta; Tuters, Stephanie

    2017-01-01

    Background: The importance of "evidence-informed practice" has risen dramatically in education and in other public policy areas. This article focuses on the importance of knowledge mobilisation strategies, processes and outputs. It is concerned with how these can support the adaptation and implementation of evidence from research and…

  4. Applying contemporary statistical techniques

    CERN Document Server

    Wilcox, Rand R

    2003-01-01

    Applying Contemporary Statistical Techniques explains why traditional statistical methods are often inadequate or outdated when applied to modern problems. Wilcox demonstrates how new and more powerful techniques address these problems far more effectively, making these modern robust methods understandable, practical, and easily accessible.* Assumes no previous training in statistics * Explains how and why modern statistical methods provide more accurate results than conventional methods* Covers the latest developments on multiple comparisons * Includes recent advanc

  5. Applied ALARA techniques

    International Nuclear Information System (INIS)

    Waggoner, L.O.

    1998-01-01

    The presentation focuses on some of the time-proven and new technologies being used to accomplish radiological work. These techniques can be applied at nuclear facilities to reduce radiation doses and protect the environment. The last reactor plants and processing facilities were shutdown and Hanford was given a new mission to put the facilities in a safe condition, decontaminate, and prepare them for decommissioning. The skills that were necessary to operate these facilities were different than the skills needed today to clean up Hanford. Workers were not familiar with many of the tools, equipment, and materials needed to accomplish:the new mission, which includes clean up of contaminated areas in and around all the facilities, recovery of reactor fuel from spent fuel pools, and the removal of millions of gallons of highly radioactive waste from 177 underground tanks. In addition, this work has to be done with a reduced number of workers and a smaller budget. At Hanford, facilities contain a myriad of radioactive isotopes that are 2048 located inside plant systems, underground tanks, and the soil. As cleanup work at Hanford began, it became obvious early that in order to get workers to apply ALARA and use hew tools and equipment to accomplish the radiological work it was necessary to plan the work in advance and get radiological control and/or ALARA committee personnel involved early in the planning process. Emphasis was placed on applying,ALARA techniques to reduce dose, limit contamination spread and minimize the amount of radioactive waste generated. Progress on the cleanup has,b6en steady and Hanford workers have learned to use different types of engineered controls and ALARA techniques to perform radiological work. The purpose of this presentation is to share the lessons learned on how Hanford is accomplishing radiological work

  6. Applied ALARA techniques

    Energy Technology Data Exchange (ETDEWEB)

    Waggoner, L.O.

    1998-02-05

    The presentation focuses on some of the time-proven and new technologies being used to accomplish radiological work. These techniques can be applied at nuclear facilities to reduce radiation doses and protect the environment. The last reactor plants and processing facilities were shutdown and Hanford was given a new mission to put the facilities in a safe condition, decontaminate, and prepare them for decommissioning. The skills that were necessary to operate these facilities were different than the skills needed today to clean up Hanford. Workers were not familiar with many of the tools, equipment, and materials needed to accomplish:the new mission, which includes clean up of contaminated areas in and around all the facilities, recovery of reactor fuel from spent fuel pools, and the removal of millions of gallons of highly radioactive waste from 177 underground tanks. In addition, this work has to be done with a reduced number of workers and a smaller budget. At Hanford, facilities contain a myriad of radioactive isotopes that are 2048 located inside plant systems, underground tanks, and the soil. As cleanup work at Hanford began, it became obvious early that in order to get workers to apply ALARA and use hew tools and equipment to accomplish the radiological work it was necessary to plan the work in advance and get radiological control and/or ALARA committee personnel involved early in the planning process. Emphasis was placed on applying,ALARA techniques to reduce dose, limit contamination spread and minimize the amount of radioactive waste generated. Progress on the cleanup has,b6en steady and Hanford workers have learned to use different types of engineered controls and ALARA techniques to perform radiological work. The purpose of this presentation is to share the lessons learned on how Hanford is accomplishing radiological work.

  7. Project mobilisation

    International Nuclear Information System (INIS)

    Clark, J.; Limbrick, A.

    1996-01-01

    This paper identifies and reviews the issues to be addressed and the procedures to be followed during the mobilisation of projects using LFG as an energy source. Knowledge of the procedures involved in project mobilisation, their sequence and probable timescales, is essential for efficient project management. It is assumed that the majority of projects will be situated on existing, licensed landfill sites and, in addition to complying with the relevant conditions of the waste management licence and original planning consent, any proposed developments on the site will require a separate planning consent. Experience in the UK indicates that obtaining planning permission rarely constitutes a barrier to the development of schemes for the utilisation of LFG. Even so, an appreciation of the applicable environmental and planning legislation is essential as this will enable the developer to recognise the main concerns of the relevant planning authority at an early stage of the project, resulting in the preparation of an informed and well-structured application for planning permission. For a LFG utilisation scheme on an existing landfill site, the need to carry out an environmental assessment (EA) as part of the application for planning permission will, in vitually all cases, be discretionary. Even if not deemed necessary by the planning authority, an EA is a useful tool at the planning application stage, to identify and address potential problems and to support discussions with bodies such as the Environment Agency, from whom consents or authorisations may be required. Carrying out an EA can thus provide for more cost-effective project development and enhanced environmental protection. Typically, the principal contractual arrangements, such as the purchase of gas or the sale of electricity, will have been established before the project mobilisation phase. However, there are many other contractural arrangements that must be established, and consents and permits that may be

  8. Exploration of clinical changes following a novel mobilisation technique for treatment of chronic low back pain: A single cohort design.

    Science.gov (United States)

    Hanson, Gail C; Jones, Bruce; Bacon, Catherine J; Moran, Robert W

    2016-07-01

    To explore clinical changes following a novel manual mobilisation technique, 24 participants who experienced 'moderate' to 'severe' chronic low back pain were recruited from new patients attending a suburban osteopathy clinic. The intervention was a previously undescribed side-lying mobilisation technique targeting the lumbosacral spine (median of 6 treatment sessions). After 8 weeks reductions were shown in Oswestry Disability Index of 15 points (95% CI: 9.3, 22.7; p pain intensity, disability and function improved in most participants following treatment. Further investigation is indicated using more robust research designs to compare this approach with other treatment approaches and usual care for the treatment of chronic low back pain. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. PEMIMPIN MOBILISATOR

    Directory of Open Access Journals (Sweden)

    H. Abdullah Syarif

    2017-10-01

    Full Text Available Every human being is a holder of responsibility. A man as leader often forgot his duty. The current conditions not only shows the weakness of the mentality of leaders in various level of office, but the societies are unruly also adds the problem. A leader is not just enough to know a solution of a problem, but the idea that solution must be applied to the problems. The characteristics of a mobilizing leader are a quick job completed with satisfactory results, efficient and effective, able to communicate, exemplary, and able in giving motivation.

  10. Kaolinite Mobilisation in Sandstone

    DEFF Research Database (Denmark)

    Rosenbrand, Esther; Fabricius, Ida Lykke; Kets, Frans

    2013-01-01

    suggest that this effect is due to kaolinite clay mobilisation from the quartz grain surface; the mobilised particles subsequently plug the pore throats and reduce the permeability irreversibly. The expected hysteresis is observed when the salinity is reduced and increased; however, in contradiction...... the mobilised kaolinite particles either remain suspended and thereby increase the fluid viscosity, or form porous aggregates that can be destabilized by hydrodynamic forces. To address how the pore scale distribution of kaolinite relates to the permeability of the entire sample, we relate permeability...

  11. Early counterpulse technique applied to vacuum interrupters

    International Nuclear Information System (INIS)

    Warren, R.W.

    1979-11-01

    Interruption of dc currents using counterpulse techniques is investigated with vacuum interrupters and a novel approach in which the counterpulse is applied before contact separation. Important increases have been achieved in this way in the maximum interruptible current as well as large reductions in contact erosion. The factors establishing these new limits are presented and ways are discussed to make further improvements

  12. Early counterpulse technique applied to vacuum interrupters

    International Nuclear Information System (INIS)

    Warren, R.W.

    1979-01-01

    Interruption of dc currents using counterpulse techniques is investigated with vacuum interrupters and a novel approach in which the counterpulse is applied before contact separation. Important increases have been achieved in this way in the maximum interruptible current and large reductions in contact erosion. The factors establishing these new limits are presented and ways are discussed to make further improvements to the maximum interruptible current

  13. Computational optimization techniques applied to microgrids planning

    DEFF Research Database (Denmark)

    Gamarra, Carlos; Guerrero, Josep M.

    2015-01-01

    Microgrids are expected to become part of the next electric power system evolution, not only in rural and remote areas but also in urban communities. Since microgrids are expected to coexist with traditional power grids (such as district heating does with traditional heating systems......), their planning process must be addressed to economic feasibility, as a long-term stability guarantee. Planning a microgrid is a complex process due to existing alternatives, goals, constraints and uncertainties. Usually planning goals conflict each other and, as a consequence, different optimization problems...... appear along the planning process. In this context, technical literature about optimization techniques applied to microgrid planning have been reviewed and the guidelines for innovative planning methodologies focused on economic feasibility can be defined. Finally, some trending techniques and new...

  14. Surface analytical techniques applied to minerals processing

    International Nuclear Information System (INIS)

    Smart, R.St.C.

    1991-01-01

    An understanding of the chemical and physical forms of the chemically altered layers on the surfaces of base metal sulphides, particularly in the form of hydroxides, oxyhydroxides and oxides, and the changes that occur in them during minerals processing lies at the core of a complete description of flotation chemistry. This paper reviews the application of a variety of surface-sensitive techniques and methodologies applied to the study of surface layers on single minerals, mixed minerals, synthetic ores and real ores. Evidence from combined XPS/SAM/SEM studies have provided images and analyses of three forms of oxide, oxyhydroxide and hydroxide products on the surfaces of single sulphide minerals, mineral mixtures and complex sulphide ores. 4 refs., 2 tabs., 4 figs

  15. Manipulation and mobilisation for neck pain contrasted against an inactive control or another active treatment.

    Science.gov (United States)

    Gross, Anita; Langevin, Pierre; Burnie, Stephen J; Bédard-Brochu, Marie-Sophie; Empey, Brian; Dugas, Estelle; Faber-Dobrescu, Michael; Andres, Cristy; Graham, Nadine; Goldsmith, Charles H; Brønfort, Gert; Hoving, Jan L; LeBlanc, Francis

    2015-09-23

    Manipulation and mobilisation are commonly used to treat neck pain. This is an update of a Cochrane review first published in 2003, and previously updated in 2010. To assess the effects of manipulation or mobilisation alone compared wiith those of an inactive control or another active treatment on pain, function, disability, patient satisfaction, quality of life and global perceived effect in adults experiencing neck pain with or without radicular symptoms and cervicogenic headache (CGH) at immediate- to long-term follow-up. When appropriate, to assess the influence of treatment characteristics (i.e. technique, dosage), methodological quality, symptom duration and subtypes of neck disorder on treatment outcomes. Review authors searched the following computerised databases to November 2014 to identify additional studies: the Cochrane Central Register of Controlled Trials (CENTRAL), MEDLINE, EMBASE and the Cumulative Index to Nursing and Allied Health Literature (CINAHL). We also searched ClinicalTrials.gov, checked references, searched citations and contacted study authors to find relevant studies. We updated this search in June 2015, but these results have not yet been incorporated. Randomised controlled trials (RCTs) undertaken to assess whether manipulation or mobilisation improves clinical outcomes for adults with acute/subacute/chronic neck pain. Two review authors independently selected studies, abstracted data, assessed risk of bias and applied Grades of Recommendation, Assessment, Development and Evaluation (GRADE) methods (very low, low, moderate, high quality). We calculated pooled risk ratios (RRs) and standardised mean differences (SMDs). We included 51 trials (2920 participants, 18 trials of manipulation/mobilisation versus control; 34 trials of manipulation/mobilisation versus another treatment, 1 trial had two comparisons). Cervical manipulation versus inactive control: For subacute and chronic neck pain, a single manipulation (three trials, no meta

  16. Applying Brainstorming Techniques to EFL Classroom

    OpenAIRE

    Toshiya, Oishi; 湘北短期大学; aPart-time Lecturer at Shohoku College

    2015-01-01

    This paper focuses on brainstorming techniques for English language learners. From the author's teaching experiences at Shohoku College during the academic year 2014-2015, the importance of brainstorming techniques was made evident. The author explored three elements of brainstorming techniques for writing using literaturereviews: lack of awareness, connecting to prior knowledge, and creativity. The literature reviews showed the advantage of using brainstorming techniques in an English compos...

  17. Nuclear radioactive techniques applied to materials research

    CERN Document Server

    Correia, João Guilherme; Wahl, Ulrich

    2011-01-01

    In this paper we review materials characterization techniques using radioactive isotopes at the ISOLDE/CERN facility. At ISOLDE intense beams of chemically clean radioactive isotopes are provided by selective ion-sources and high-resolution isotope separators, which are coupled on-line with particle accelerators. There, new experiments are performed by an increasing number of materials researchers, which use nuclear spectroscopic techniques such as Mössbauer, Perturbed Angular Correlations (PAC), beta-NMR and Emission Channeling with short-lived isotopes not available elsewhere. Additionally, diffusion studies and traditionally non-radioactive techniques as Deep Level Transient Spectroscopy, Hall effect and Photoluminescence measurements are performed on radioactive doped samples, providing in this way the element signature upon correlation of the time dependence of the signal with the isotope transmutation half-life. Current developments, applications and perspectives of using radioactive ion beams and tech...

  18. Applying Mixed Methods Techniques in Strategic Planning

    Science.gov (United States)

    Voorhees, Richard A.

    2008-01-01

    In its most basic form, strategic planning is a process of anticipating change, identifying new opportunities, and executing strategy. The use of mixed methods, blending quantitative and qualitative analytical techniques and data, in the process of assembling a strategic plan can help to ensure a successful outcome. In this article, the author…

  19. Applying Nonverbal Techniques to Organizational Diagnosis.

    Science.gov (United States)

    Tubbs, Stewart L.; Koske, W. Cary

    Ongoing research programs conducted at General Motors Institute are motivated by the practical objective of improving the company's organizational effectiveness. Computer technology is being used whenever possible; for example, a technique developed by Herman Chernoff was used to process data from a survey of employee attitudes into 18 different…

  20. Applying Cooperative Techniques in Teaching Problem Solving

    Directory of Open Access Journals (Sweden)

    Krisztina Barczi

    2013-12-01

    Full Text Available Teaching how to solve problems – from solving simple equations to solving difficult competition tasks – has been one of the greatest challenges for mathematics education for many years. Trying to find an effective method is an important educational task. Among others, the question arises as to whether a method in which students help each other might be useful. The present article describes part of an experiment that was designed to determine the effects of cooperative teaching techniques on the development of problem-solving skills.

  1. Basic principles of applied nuclear techniques

    International Nuclear Information System (INIS)

    Basson, J.K.

    1976-01-01

    The technological applications of radioactive isotopes and radiation in South Africa have grown steadily since the first consignment of man-made radioisotopes reached this country in 1948. By the end of 1975 there were 412 authorised non-medical organisations (327 industries) using hundreds of sealed sources as well as their fair share of the thousands of radioisotope consignments, annually either imported or produced locally (mainly for medical purposes). Consequently, it is necessary for South African technologists to understand the principles of radioactivity in order to appreciate the industrial applications of nuclear techniques [af

  2. Dosimetry techniques applied to thermoluminescent age estimation

    International Nuclear Information System (INIS)

    Erramli, H.

    1986-12-01

    The reliability and the ease of the field application of the measuring techniques of natural radioactivity dosimetry are studied. The natural radioactivity in minerals in composed of the internal dose deposited by alpha and beta radiations issued from the sample itself and the external dose deposited by gamma and cosmic radiations issued from the surroundings of the sample. Two technics for external dosimetry are examined in details. TL Dosimetry and field gamma dosimetry. Calibration and experimental conditions are presented. A new integrated dosimetric method for internal and external dose measure is proposed: the TL dosimeter is placed in the soil in exactly the same conditions as the sample ones, during a time long enough for the total dose evaluation [fr

  3. Tracer techniques applied to groundwater studies

    International Nuclear Information System (INIS)

    Sanchez, W.

    1975-01-01

    The determination of several aquifer characteristics, primarily in the satured zone, namely: porosity, permeability, transmissivity, dispersivity, direction and velocity of sub-surface water is presented. These techniques are based on artificial radioisotopes utilization. Only field determination of porosity are considered here and their advantage over laboratory measurements are: better representation of volume average, insensibility to local inhomogenities and no distortion of the structure due to sampling. The radioisotope dilution method is used to obtain an independent and direct measurement of the filtration velocity in a water-bearing formation under natural or induced hydraulic gradient. The velocity of the flow is usually calculated from Darcy's formula through the measurement of gradients and requires a knowledge of the permeability of the formation. The filtration velocity interpreted in conjunction with other parameters can, under favourable conditions, provide valuable information on the permeability, transmissibility and amount of water moving through an aquifer

  4. Nuclear analytical techniques applied to forensic chemistry

    International Nuclear Information System (INIS)

    Nicolau, Veronica; Montoro, Silvia; Pratta, Nora; Giandomenico, Angel Di

    1999-01-01

    Gun shot residues produced by firing guns are mainly composed by visible particles. The individual characterization of these particles allows distinguishing those ones containing heavy metals, from gun shot residues, from those having a different origin or history. In this work, the results obtained from the study of gun shot residues particles collected from hands are presented. The aim of the analysis is to establish whether a person has shot a firing gun has been in contact with one after the shot has been produced. As reference samples, particles collected hands of persons affected to different activities were studied to make comparisons. The complete study was based on the application of nuclear analytical techniques such as Scanning Electron Microscopy, Energy Dispersive X Ray Electron Probe Microanalysis and Graphite Furnace Atomic Absorption Spectrometry. The essays allow to be completed within time compatible with the forensic requirements. (author)

  5. Motion Capture Technique Applied Research in Sports Technique Diagnosis

    Directory of Open Access Journals (Sweden)

    Zhiwu LIU

    2014-09-01

    Full Text Available The motion capture technology system definition is described in the paper, and its components are researched, the key parameters are obtained from motion technique, the quantitative analysis are made on technical movements, the method of motion capture technology is proposed in sport technical diagnosis. That motion capture step includes calibration system, to attached landmarks to the tester; to capture trajectory, and to analyze the collected data.

  6. Chemical vapor deposition: A technique for applying protective coatings

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, T.C. Sr.; Bowman, M.G.

    1979-01-01

    Chemical vapor deposition is discussed as a technique for applying coatings for materials protection in energy systems. The fundamentals of the process are emphasized in order to establish a basis for understanding the relative advantages and limitations of the technique. Several examples of the successful application of CVD coating are described. 31 refs., and 18 figs.

  7. Use of a 137Cs re-sampling technique to investigate temporal changes in soil erosion and sediment mobilisation for a small forested catchment in southern Italy

    International Nuclear Information System (INIS)

    Porto, Paolo; Walling, Des E.; Alewell, Christine; Callegari, Giovanni; Mabit, Lionel; Mallimo, Nicola; Meusburger, Katrin; Zehringer, Markus

    2014-01-01

    Soil erosion and both its on-site and off-site impacts are increasingly seen as a serious environmental problem across the world. The need for an improved evidence base on soil loss and soil redistribution rates has directed attention to the use of fallout radionuclides, and particularly 137 Cs, for documenting soil redistribution rates. This approach possesses important advantages over more traditional means of documenting soil erosion and soil redistribution. However, one key limitation of the approach is the time-averaged or lumped nature of the estimated erosion rates. In nearly all cases, these will relate to the period extending from the main period of bomb fallout to the time of sampling. Increasing concern for the impact of global change, particularly that related to changing land use and climate change, has frequently directed attention to the need to document changes in soil redistribution rates within this period. Re-sampling techniques, which should be distinguished from repeat-sampling techniques, have the potential to meet this requirement. As an example, the use of a re-sampling technique to derive estimates of the mean annual net soil loss from a small (1.38 ha) forested catchment in southern Italy is reported. The catchment was originally sampled in 1998 and samples were collected from points very close to the original sampling points again in 2013. This made it possible to compare the estimate of mean annual erosion for the period 1954–1998 with that for the period 1999–2013. The availability of measurements of sediment yield from the catchment for parts of the overall period made it possible to compare the results provided by the 137 Cs re-sampling study with the estimates of sediment yield for the same periods. In order to compare the estimates of soil loss and sediment yield for the two different periods, it was necessary to establish the uncertainty associated with the individual estimates. In the absence of a generally accepted procedure

  8. Manipulation or Mobilisation for Neck Pain

    NARCIS (Netherlands)

    Gross, Anita; Miller, Jordan; D'Sylva, Jonathan; Burnie, Stephen J.; Goldsmith, Charles H.; Graham, Nadine; Haines, Ted; Brønfort, Gert; Hoving, Jan L.

    2010-01-01

    Background Manipulation and mobilisation are often used, either alone or combined with other treatment approaches, to treat neck pain. Objectives To assess if manipulation or mobilisation improves pain, function/disability, patient satisfaction, quality of life, and global perceived effect in adults

  9. Applying DEA Technique to Library Evaluation in Academic Research Libraries.

    Science.gov (United States)

    Shim, Wonsik

    2003-01-01

    This study applied an analytical technique called Data Envelopment Analysis (DEA) to calculate the relative technical efficiency of 95 academic research libraries, all members of the Association of Research Libraries. DEA, with the proper model of library inputs and outputs, can reveal best practices in the peer groups, as well as the technical…

  10. Positioning and early mobilisation in stroke.

    Science.gov (United States)

    Keating, Moira; Penney, Maree; Russell, Petra; Bailey, Emma

    Stroke unit care, providing early rehabilitation, improves long-term outcomes for patients following a stroke. Early mobilisation and good positioning are recognised as key aspects of care in stroke units. Nurses working on stroke units have an important role because they are able to implement positioning and early mobilisation strategies 24 hours a day, reducing the risk of complications and improving functional recovery. Patients benefit if nurses work effectively with the therapy team in positioning and early mobilisation. Nurses also need appropriate training and expertise to make best use of specialist equipment.

  11. [Technique and value of direct MR arthrography applying articular distraction].

    Science.gov (United States)

    Becce, Fabio; Wettstein, Michael; Guntern, Daniel; Mouhsine, Elyazid; Palhais, Nuno; Theumann, Nicolas

    2010-02-24

    Direct MR arthrography has a better diagnostic accuracy than MR imaging alone. However, contrast material is not always homogeneously distributed in the articular space. Lesions of cartilage surfaces or intra-articular soft tissues can thus be misdiagnosed. Concomitant application of axial traction during MR arthrography leads to articular distraction. This enables better distribution of contrast material in the joint and better delineation of intra-articular structures. Therefore, this technique improves detection of cartilage lesions. Moreover, the axial stress applied on articular structures may reveal lesions invisible on MR images without traction. Based on our clinical experience, we believe that this relatively unknown technique is promising and should be further developed.

  12. Determination of palladium in biological samples applying nuclear analytical techniques

    International Nuclear Information System (INIS)

    Cavalcante, Cassio Q.; Sato, Ivone M.; Salvador, Vera L. R.; Saiki, Mitiko

    2008-01-01

    This study presents Pd determinations in bovine tissue samples containing palladium prepared in the laboratory, and CCQM-P63 automotive catalyst materials of the Proficiency Test, using instrumental thermal and epithermal neutron activation analysis and energy dispersive X-ray fluorescence techniques. Solvent extraction and solid phase extraction procedures were also applied to separate Pd from interfering elements before the irradiation in the nuclear reactor. The results obtained by different techniques were compared against each other to examine sensitivity, precision and accuracy. (author)

  13. Applying of USB interface technique in nuclear spectrum acquisition system

    International Nuclear Information System (INIS)

    Zhou Jianbin; Huang Jinhua

    2004-01-01

    This paper introduces applying of USB technique and constructing nuclear spectrum acquisition system via PC's USB interface. The authors choose the USB component USB100 module and the W77E58μc to do the key work. It's easy to apply USB interface technique, when USB100 module is used. USB100 module can be treated as a common I/O component for the μc controller, and can be treated as a communication interface (COM) when connected to PC' USB interface. It's easy to modify the PC's program for the new system with USB100 module. The authors can smoothly change from ISA, RS232 bus to USB bus. (authors)

  14. Diagonal ordering operation technique applied to Morse oscillator

    Energy Technology Data Exchange (ETDEWEB)

    Popov, Dušan, E-mail: dusan_popov@yahoo.co.uk [Politehnica University Timisoara, Department of Physical Foundations of Engineering, Bd. V. Parvan No. 2, 300223 Timisoara (Romania); Dong, Shi-Hai [CIDETEC, Instituto Politecnico Nacional, Unidad Profesional Adolfo Lopez Mateos, Mexico D.F. 07700 (Mexico); Popov, Miodrag [Politehnica University Timisoara, Department of Steel Structures and Building Mechanics, Traian Lalescu Street, No. 2/A, 300223 Timisoara (Romania)

    2015-11-15

    We generalize the technique called as the integration within a normally ordered product (IWOP) of operators referring to the creation and annihilation operators of the harmonic oscillator coherent states to a new operatorial approach, i.e. the diagonal ordering operation technique (DOOT) about the calculations connected with the normally ordered product of generalized creation and annihilation operators that generate the generalized hypergeometric coherent states. We apply this technique to the coherent states of the Morse oscillator including the mixed (thermal) state case and get the well-known results achieved by other methods in the corresponding coherent state representation. Also, in the last section we construct the coherent states for the continuous dynamics of the Morse oscillator by using two new methods: the discrete–continuous limit, respectively by solving a finite difference equation. Finally, we construct the coherent states corresponding to the whole Morse spectrum (discrete plus continuous) and demonstrate their properties according the Klauder’s prescriptions.

  15. Applying recursive numerical integration techniques for solving high dimensional integrals

    International Nuclear Information System (INIS)

    Ammon, Andreas; Genz, Alan; Hartung, Tobias; Jansen, Karl; Volmer, Julia; Leoevey, Hernan

    2016-11-01

    The error scaling for Markov-Chain Monte Carlo techniques (MCMC) with N samples behaves like 1/√(N). This scaling makes it often very time intensive to reduce the error of computed observables, in particular for applications in lattice QCD. It is therefore highly desirable to have alternative methods at hand which show an improved error scaling. One candidate for such an alternative integration technique is the method of recursive numerical integration (RNI). The basic idea of this method is to use an efficient low-dimensional quadrature rule (usually of Gaussian type) and apply it iteratively to integrate over high-dimensional observables and Boltzmann weights. We present the application of such an algorithm to the topological rotor and the anharmonic oscillator and compare the error scaling to MCMC results. In particular, we demonstrate that the RNI technique shows an error scaling in the number of integration points m that is at least exponential.

  16. Technique applied in electrical power distribution for Satellite Launch Vehicle

    Directory of Open Access Journals (Sweden)

    João Maurício Rosário

    2010-09-01

    Full Text Available The Satellite Launch Vehicle electrical network, which is currently being developed in Brazil, is sub-divided for analysis in the following parts: Service Electrical Network, Controlling Electrical Network, Safety Electrical Network and Telemetry Electrical Network. During the pre-launching and launching phases, these electrical networks are associated electrically and mechanically to the structure of the vehicle. In order to succeed in the integration of these electrical networks it is necessary to employ techniques of electrical power distribution, which are proper to Launch Vehicle systems. This work presents the most important techniques to be considered in the characterization of the electrical power supply applied to Launch Vehicle systems. Such techniques are primarily designed to allow the electrical networks, when submitted to the single-phase fault to ground, to be able of keeping the power supply to the loads.

  17. Applying recursive numerical integration techniques for solving high dimensional integrals

    Energy Technology Data Exchange (ETDEWEB)

    Ammon, Andreas [IVU Traffic Technologies AG, Berlin (Germany); Genz, Alan [Washington State Univ., Pullman, WA (United States). Dept. of Mathematics; Hartung, Tobias [King' s College, London (United Kingdom). Dept. of Mathematics; Jansen, Karl; Volmer, Julia [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany). John von Neumann-Inst. fuer Computing NIC; Leoevey, Hernan [Humboldt Univ. Berlin (Germany). Inst. fuer Mathematik

    2016-11-15

    The error scaling for Markov-Chain Monte Carlo techniques (MCMC) with N samples behaves like 1/√(N). This scaling makes it often very time intensive to reduce the error of computed observables, in particular for applications in lattice QCD. It is therefore highly desirable to have alternative methods at hand which show an improved error scaling. One candidate for such an alternative integration technique is the method of recursive numerical integration (RNI). The basic idea of this method is to use an efficient low-dimensional quadrature rule (usually of Gaussian type) and apply it iteratively to integrate over high-dimensional observables and Boltzmann weights. We present the application of such an algorithm to the topological rotor and the anharmonic oscillator and compare the error scaling to MCMC results. In particular, we demonstrate that the RNI technique shows an error scaling in the number of integration points m that is at least exponential.

  18. Mobilising Investment in Energy Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    Taxes, loans and grants, trading schemes and white certificates, public procurement and investment in R&D or infrastructure: known collectively as 'economic instruments', these tools can be powerful means of mobilising the finances needed to achieve policy goals by implementing energy efficiency measures. The role of economic instruments is to kick-start the private financial markets and to motivate private investors to fund EE measures. They should reinforce and promote energy performance regulations. This IEA analysis addresses the fact that, to date, relatively little effort has been directed toward evaluating how well economic instruments work. Using the buildings sector to illustrate how such measures can support energy efficiency, this paper can help policy makers better select and design economic instruments appropriate to their policy objectives and national contexts. This report’s three main aims are to: 1) Examine how economic instruments are currently used in energy efficiency policy; 2) Consider how economic instruments can be more effective and efficient in supporting low-energy buildings; and 3) Assess how economic instruments should be funded, where public outlay is needed. Detailed case studies in this report assess examples of economic instruments for energy efficiency in the buildings sector in Canada (grants), France (tax relief and loans), Germany (loans and grants), Ireland (grants) and Italy (white certificates and tax relief).

  19. Three-dimensional integrated CAE system applying computer graphic technique

    International Nuclear Information System (INIS)

    Kato, Toshisada; Tanaka, Kazuo; Akitomo, Norio; Obata, Tokayasu.

    1991-01-01

    A three-dimensional CAE system for nuclear power plant design is presented. This system utilizes high-speed computer graphic techniques for the plant design review, and an integrated engineering database for handling the large amount of nuclear power plant engineering data in a unified data format. Applying this system makes it possible to construct a nuclear power plant using only computer data from the basic design phase to the manufacturing phase, and it increases the productivity and reliability of the nuclear power plants. (author)

  20. Applying field mapping refractive beam shapers to improve holographic techniques

    Science.gov (United States)

    Laskin, Alexander; Williams, Gavin; McWilliam, Richard; Laskin, Vadim

    2012-03-01

    Performance of various holographic techniques can be essentially improved by homogenizing the intensity profile of the laser beam with using beam shaping optics, for example, the achromatic field mapping refractive beam shapers like πShaper. The operational principle of these devices presumes transformation of laser beam intensity from Gaussian to flattop one with high flatness of output wavefront, saving of beam consistency, providing collimated output beam of low divergence, high transmittance, extended depth of field, negligible residual wave aberration, and achromatic design provides capability to work with several laser sources with different wavelengths simultaneously. Applying of these beam shapers brings serious benefits to the Spatial Light Modulator based techniques like Computer Generated Holography or Dot-Matrix mastering of security holograms since uniform illumination of an SLM allows simplifying mathematical calculations and increasing predictability and reliability of the imaging results. Another example is multicolour Denisyuk holography when the achromatic πShaper provides uniform illumination of a field at various wavelengths simultaneously. This paper will describe some design basics of the field mapping refractive beam shapers and optical layouts of their applying in holographic systems. Examples of real implementations and experimental results will be presented as well.

  1. Archaeometry: nuclear and conventional techniques applied to the archaeological research

    International Nuclear Information System (INIS)

    Esparza L, R.; Cardenas G, E.

    2005-01-01

    The book that now is presented is formed by twelve articles that approach from different perspective topics as the archaeological prospecting, the analysis of the pre hispanic and colonial ceramic, the obsidian and the mural painting, besides dating and questions about the data ordaining. Following the chronological order in which the exploration techniques and laboratory studies are required, there are presented in the first place the texts about the systematic and detailed study of the archaeological sites, later we pass to relative topics to the application of diverse nuclear techniques as PIXE, RBS, XRD, NAA, SEM, Moessbauer spectroscopy and other conventional techniques. The multidisciplinary is an aspect that highlights in this work, that which owes to the great specialization of the work that is presented even in the archaeological studies including in the open ground of the topography, mapping, excavation and, of course, in the laboratory tests. Most of the articles are the result of several years of investigation and it has been consigned in the responsibility of each article. The texts here gathered emphasize the technical aspects of each investigation, the modern compute systems applied to the prospecting and the archaeological mapping, the chemical and physical analysis of organic materials, of metal artifacts, of diverse rocks used in the pre hispanic epoch, of mural and ceramic paintings, characteristics that justly underline the potential of the collective works. (Author)

  2. Potential Phosphorus Mobilisation in Peat Soils

    DEFF Research Database (Denmark)

    Forsmann, Ditte M.; Kjærgaard, Charlotte

    2012-01-01

    Re-establishment of wetlands on peat soils containing phosphorus bound to iron(III)-oxides can lead to an undesirable phosphorus loss to the aquatic environment due to the reductive dissolution of iron(III)-oxides. Thus it is important to be able to assess the potential phosphorus mobilisation from...... peat soils before a re-establishment takes place. The potential phosphorus mobilisation from a peat soil depends not only on the geochemical characteristics but also on the redox conditions, the hydrological regime in the area as well as the hydro-physical properties of the soil. The hypothesis...... for this study is (i) the release of phosphorus in peat is controlled by the geochemistry; (ii) the mobilisation of phosphorus is controlled by both geochemistry and hydro-physics of the soil. For this study, 10 Danish riparian lowland areas with peat soil were selected based on their geochemical characteristics...

  3. Applying Metrological Techniques to Satellite Fundamental Climate Data Records

    Science.gov (United States)

    Woolliams, Emma R.; Mittaz, Jonathan PD; Merchant, Christopher J.; Hunt, Samuel E.; Harris, Peter M.

    2018-02-01

    Quantifying long-term environmental variability, including climatic trends, requires decadal-scale time series of observations. The reliability of such trend analysis depends on the long-term stability of the data record, and understanding the sources of uncertainty in historic, current and future sensors. We give a brief overview on how metrological techniques can be applied to historical satellite data sets. In particular we discuss the implications of error correlation at different spatial and temporal scales and the forms of such correlation and consider how uncertainty is propagated with partial correlation. We give a form of the Law of Propagation of Uncertainties that considers the propagation of uncertainties associated with common errors to give the covariance associated with Earth observations in different spectral channels.

  4. Applying AI techniques to improve alarm display effectiveness

    International Nuclear Information System (INIS)

    Gross, J.M.; Birrer, S.A.; Crosberg, D.R.

    1987-01-01

    The Alarm Filtering System (AFS) addresses the problem of information overload in a control room during abnormal operations. Since operators can miss vital information during these periods, systems which emphasize important messages are beneficial. AFS uses the artificial intelligence (AI) technique of object-oriented programming to filter and dynamically prioritize alarm messages. When an alarm's status changes, AFS determines the relative importance of that change according to the current process state. AFS bases that relative importance on relationships the newly changed alarm has with other activated alarms. Evaluations of a alarm importance take place without regard to the activation sequence of alarm signals. The United States Department of Energy has applied for a patent on the approach used in this software. The approach was originally developed by EG and G Idaho for a nuclear reactor control room

  5. Airflow measurement techniques applied to radon mitigation problems

    International Nuclear Information System (INIS)

    Harrje, D.T.; Gadsby, K.J.

    1989-01-01

    During the past decade a multitude of diagnostic procedures associated with the evaluation of air infiltration and air leakage sites have been developed. The spirit of international cooperation and exchange of ideas within the AIC-AIVC conferences has greatly facilitated the adoption and use of these measurement techniques in the countries participating in Annex V. But wide application of such diagnostic methods are not limited to air infiltration alone. The subject of this paper concerns the ways to evaluate and improve radon reduction in buildings using diagnostic methods directly related to developments familiar to the AIVC. Radon problems are certainly not unique to the United States, and the methods described here have to a degree been applied by researchers of other countries faced with similar problems. The radon problem involves more than a harmful pollutant of the living spaces of our buildings -- it also involves energy to operate radon removal equipment and the loss of interior conditioned air as a direct result. The techniques used for air infiltration evaluation will be shown to be very useful in dealing with the radon mitigation challenge. 10 refs., 7 figs., 1 tab

  6. Missing link or not, mobilise against delirium.

    Science.gov (United States)

    Page, Valerie J; Casarin, Annalisa

    2014-01-31

    Delirium is known to be a predictor of adverse outcomes. In a prospective study Abelha and colleagues showed that postoperative delirium was an independent risk factor for deterioration in functional capacity following discharge. While evidence for causality remains elusive, there is no doubt that patients who develop delirium are left with new functional and cognitive impairment. Finding a pharmacological treatment for the prevention and treatment of delirium is a priority in delirium research and the results of ongoing trials are awaited. Early mobilisation of ICU patients has been demonstrated to decrease delirium and improve functional outcomes. Resources should be directed to appropriate, progressive mobilisation of all critically ill patients as a priority.

  7. Analytical techniques applied to study cultural heritage objects

    International Nuclear Information System (INIS)

    Rizzutto, M.A.; Curado, J.F.; Bernardes, S.; Campos, P.H.O.V.; Kajiya, E.A.M.; Silva, T.F.; Rodrigues, C.L.; Moro, M.; Tabacniks, M.; Added, N.

    2015-01-01

    The scientific study of artistic and cultural heritage objects have been routinely performed in Europe and the United States for decades. In Brazil this research area is growing, mainly through the use of physical and chemical characterization methods. Since 2003 the Group of Applied Physics with Particle Accelerators of the Physics Institute of the University of Sao Paulo (GFAA-IF) has been working with various methodologies for material characterization and analysis of cultural objects. Initially using ion beam analysis performed with Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and recently Ion Beam Induced Luminescence (IBIL), for the determination of the elements and chemical compounds in the surface layers. These techniques are widely used in the Laboratory of Materials Analysis with Ion Beams (LAMFI-USP). Recently, the GFAA expanded the studies to other possibilities of analysis enabled by imaging techniques that coupled with elemental and compositional characterization provide a better understanding on the materials and techniques used in the creative process in the manufacture of objects. The imaging analysis, mainly used to examine and document artistic and cultural heritage objects, are performed through images with visible light, infrared reflectography (IR), fluorescence with ultraviolet radiation (UV), tangential light and digital radiography. Expanding more the possibilities of analysis, new capabilities were added using portable equipment such as Energy Dispersive X-Ray Fluorescence (ED-XRF) and Raman Spectroscopy that can be used for analysis 'in situ' at the museums. The results of these analyzes are providing valuable information on the manufacturing process and have provided new information on objects of different University of Sao Paulo museums. Improving the arsenal of cultural heritage analysis it was recently constructed an 3D robotic stage for the precise positioning of samples in the external beam setup

  8. Analytical techniques applied to study cultural heritage objects

    Energy Technology Data Exchange (ETDEWEB)

    Rizzutto, M.A.; Curado, J.F.; Bernardes, S.; Campos, P.H.O.V.; Kajiya, E.A.M.; Silva, T.F.; Rodrigues, C.L.; Moro, M.; Tabacniks, M.; Added, N., E-mail: rizzutto@if.usp.br [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Fisica

    2015-07-01

    The scientific study of artistic and cultural heritage objects have been routinely performed in Europe and the United States for decades. In Brazil this research area is growing, mainly through the use of physical and chemical characterization methods. Since 2003 the Group of Applied Physics with Particle Accelerators of the Physics Institute of the University of Sao Paulo (GFAA-IF) has been working with various methodologies for material characterization and analysis of cultural objects. Initially using ion beam analysis performed with Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and recently Ion Beam Induced Luminescence (IBIL), for the determination of the elements and chemical compounds in the surface layers. These techniques are widely used in the Laboratory of Materials Analysis with Ion Beams (LAMFI-USP). Recently, the GFAA expanded the studies to other possibilities of analysis enabled by imaging techniques that coupled with elemental and compositional characterization provide a better understanding on the materials and techniques used in the creative process in the manufacture of objects. The imaging analysis, mainly used to examine and document artistic and cultural heritage objects, are performed through images with visible light, infrared reflectography (IR), fluorescence with ultraviolet radiation (UV), tangential light and digital radiography. Expanding more the possibilities of analysis, new capabilities were added using portable equipment such as Energy Dispersive X-Ray Fluorescence (ED-XRF) and Raman Spectroscopy that can be used for analysis 'in situ' at the museums. The results of these analyzes are providing valuable information on the manufacturing process and have provided new information on objects of different University of Sao Paulo museums. Improving the arsenal of cultural heritage analysis it was recently constructed an 3D robotic stage for the precise positioning of samples in the external beam setup

  9. Applying advanced digital signal processing techniques in industrial radioisotopes applications

    International Nuclear Information System (INIS)

    Mahmoud, H.K.A.E.

    2012-01-01

    Radioisotopes can be used to obtain signals or images in order to recognize the information inside the industrial systems. The main problems of using these techniques are the difficulty of identification of the obtained signals or images and the requirement of skilled experts for the interpretation process of the output data of these applications. Now, the interpretation of the output data from these applications is performed mainly manually, depending heavily on the skills and the experience of trained operators. This process is time consuming and the results typically suffer from inconsistency and errors. The objective of the thesis is to apply the advanced digital signal processing techniques for improving the treatment and the interpretation of the output data from the different Industrial Radioisotopes Applications (IRA). This thesis focuses on two IRA; the Residence Time Distribution (RTD) measurement and the defect inspection of welded pipes using a gamma source (gamma radiography). In RTD measurement application, this thesis presents methods for signal pre-processing and modeling of the RTD signals. Simulation results have been presented for two case studies. The first case study is a laboratory experiment for measuring the RTD in a water flow rig. The second case study is an experiment for measuring the RTD in a phosphate production unit. The thesis proposes an approach for RTD signal identification in the presence of noise. In this approach, after signal processing, the Mel Frequency Cepstral Coefficients (MFCCs) and polynomial coefficients are extracted from the processed signal or from one of its transforms. The Discrete Wavelet Transform (DWT), Discrete Cosine Transform (DCT), and Discrete Sine Transform (DST) have been tested and compared for efficient feature extraction. Neural networks have been used for matching of the extracted features. Furthermore, the Power Density Spectrum (PDS) of the RTD signal has been also used instead of the discrete

  10. Mobilising private adaptation finance: developed country perspectives

    NARCIS (Netherlands)

    Pauw, W.P.

    2017-01-01

    Abstract The private sector is one of the sources of finance included in developed countries’ pledge in the UN climate negotiations to mobilise $100 billion annually by 2020 to support developing countries’ efforts to address climate change. For adaptation in particular, it remains unclear what

  11. Collaborative Research Partnerships for Knowledge Mobilisation

    Science.gov (United States)

    Edelstein, Hilary

    2016-01-01

    This study examines elements of collaborative research partnerships (CRPs) between university researchers and organisations who engage in knowledge mobilisation activities in education. The study uses key informant interviews and document analysis from one type of partnership, and a survey of university-community partnerships across Canada to…

  12. Understanding the Mechanism of Arsenic Mobilisation and ...

    African Journals Online (AJOL)

    Michael

    2017-06-01

    Jun 1, 2017 ... Arsenic Mobilisation and Behaviour in Tailings Dams”, Ghana Mining Journal, ... chronic lung disease, gangrene of toes/black foot disease, body weakness, skin cancer and solid swelling of legs, osteoporosis, decreased birth ..... of soils and waters in and around the Imcheon ... Johnsongrass and Cotton.

  13. Satellite SAR interferometric techniques applied to emergency mapping

    Science.gov (United States)

    Stefanova Vassileva, Magdalena; Riccardi, Paolo; Lecci, Daniele; Giulio Tonolo, Fabio; Boccardo Boccardo, Piero; Chiesa, Giuliana; Angeluccetti, Irene

    2017-04-01

    This paper aim to investigate the capabilities of the currently available SAR interferometric algorithms in the field of emergency mapping. Several tests have been performed exploiting the Copernicus Sentinel-1 data using the COTS software ENVI/SARscape 5.3. Emergency Mapping can be defined as "creation of maps, geo-information products and spatial analyses dedicated to providing situational awareness emergency management and immediate crisis information for response by means of extraction of reference (pre-event) and crisis (post-event) geographic information/data from satellite or aerial imagery". The conventional differential SAR interferometric technique (DInSAR) and the two currently available multi-temporal SAR interferometric approaches, i.e. Permanent Scatterer Interferometry (PSI) and Small BAseline Subset (SBAS), have been applied to provide crisis information useful for the emergency management activities. Depending on the considered Emergency Management phase, it may be distinguished between rapid mapping, i.e. fast provision of geospatial data regarding the area affected for the immediate emergency response, and monitoring mapping, i.e. detection of phenomena for risk prevention and mitigation activities. In order to evaluate the potential and limitations of the aforementioned SAR interferometric approaches for the specific rapid and monitoring mapping application, five main factors have been taken into account: crisis information extracted, input data required, processing time and expected accuracy. The results highlight that DInSAR has the capacity to delineate areas affected by large and sudden deformations and fulfills most of the immediate response requirements. The main limiting factor of interferometry is the availability of suitable SAR acquisition immediately after the event (e.g. Sentinel-1 mission characterized by 6-day revisiting time may not always satisfy the immediate emergency request). PSI and SBAS techniques are suitable to produce

  14. [Molecular techniques applied in species identification of Toxocara].

    Science.gov (United States)

    Fogt, Renata

    2006-01-01

    Toxocarosis is still an important and actual problem in human medicine. It can manifest as visceral (VLM), ocular (OLM) or covert (CT) larva migrans syndroms. Complicated life cycle of Toxocara, lack of easy and practical methods of species differentiation of the adult nematode and embarrassing in recognition of the infection in definitive hosts create difficulties in fighting with the infection. Although studies on human toxocarosis have been continued for over 50 years there is no conclusive answer, which of species--T. canis or T. cati constitutes a greater risk of transmission of the nematode to man. Neither blood serological examinations nor microscopic observations of the morphological features of the nematode give the satisfied answer on the question. Since the 90-ths molecular methods were developed for species identification and became useful tools being widely applied in parasitological diagnosis. This paper cover the survey of methods of DNA analyses used for identification of Toxocara species. The review may be helpful for researchers focused on Toxocara and toxocarosis as well as on detection of new species. The following techniques are described: PCR (Polymerase Chain Reaction), RFLP (Restriction Fragment Length Polymorphism), RAPD (Random Amplified Polymorphic DNA) and SSCP (Single Strand Conformation Polymorphism).

  15. Volcanic Monitoring Techniques Applied to Controlled Fragmentation Experiments

    Science.gov (United States)

    Kueppers, U.; Alatorre-Ibarguengoitia, M. A.; Hort, M. K.; Kremers, S.; Meier, K.; Scharff, L.; Scheu, B.; Taddeucci, J.; Dingwell, D. B.

    2010-12-01

    Volcanic eruptions are an inevitable natural threat. The range of eruptive styles is large and short term fluctuations of explosivity or vent position pose a large risk that is not necessarily confined to the immediate vicinity of a volcano. Explosive eruptions rather may also affect aviation, infrastructure and climate, regionally as well as globally. Multiparameter monitoring networks are deployed on many active volcanoes to record signs of magmatic processes and help elucidate the secrets of volcanic phenomena. However, our mechanistic understanding of many processes hiding in recorded signals is still poor. As a direct consequence, a solid interpretation of the state of a volcano is still a challenge. In an attempt to bridge this gap, we combined volcanic monitoring and experimental volcanology. We performed 15 well-monitored, field-based, experiments and fragmented natural rock samples from Colima volcano (Mexico) by rapid decompression. We used cylindrical samples of 60 mm height and 25 mm and 60 mm diameter, respectively, and 25 and 35 vol.% open porosity. The applied pressure range was from 4 to 18 MPa. Using different experimental set-ups, the pressurised volume above the samples ranged from 60 - 170 cm3. The experiments were performed at ambient conditions and at controlled sample porosity and size, confinement geometry, and applied pressure. The experiments have been thoroughly monitored with 1) Doppler Radar (DR), 2) high-speed and high-definition cameras, 3) acoustic and infrasound sensors, 4) pressure transducers, and 5) electrically conducting wires. Our aim was to check for common results achieved by the different approaches and, if so, calibrate state-of-the-art monitoring tools. We present how the velocity of the ejected pyroclasts was measured by and evaluated for the different approaches and how it was affected by the experimental conditions and sample characteristics. We show that all deployed instruments successfully measured the pyroclast

  16. Non destructive assay techniques applied to nuclear materials

    International Nuclear Information System (INIS)

    Gavron, A.

    2001-01-01

    Nondestructive assay is a suite of techniques that has matured and become precise, easily implementable, and remotely usable. These techniques provide elaborate safeguards of nuclear material by providing the necessary information for materials accounting. NDA techniques are ubiquitous, reliable, essentially tamper proof, and simple to use. They make the world a safer place to live in, and they make nuclear energy viable. (author)

  17. Photoacoustic technique applied to the study of skin and leather

    International Nuclear Information System (INIS)

    Vargas, M.; Varela, J.; Hernandez, L.; Gonzalez, A.

    1998-01-01

    In this paper the photoacoustic technique is used in bull skin for the determination of thermal and optical properties as a function of the tanning process steps. Our results show that the photoacoustic technique is sensitive to the study of physical changes in this kind of material due to the tanning process

  18. NEW TECHNIQUES APPLIED IN ECONOMICS. ARTIFICIAL NEURAL NETWORK

    Directory of Open Access Journals (Sweden)

    Constantin Ilie

    2009-05-01

    Full Text Available The present paper has the objective to inform the public regarding the use of new techniques for the modeling, simulate and forecast of system from different field of activity. One of those techniques is Artificial Neural Network, one of the artificial in

  19. Biomechanical study of the funnel technique applied in thoracic ...

    African Journals Online (AJOL)

    of vertebra was made for injury model of anterior and central column ... data were collected to eliminate creep and relaxation of soft tissues in .... 3 Pullout strength curve for Magerl technique (A) and Funnel technique (B). 210x164mm (72 x 72 ...

  20. The Mobilisation of Muslim Women in Denmark

    DEFF Research Database (Denmark)

    Pristed Nielsen, Helene

    Under the headline of ‘the mobilisation of Muslim women in Denmark', this paper contains a series of introductory considerations as well as a few preliminary findings on the relatively unexplored question of how and why Muslim women in Denmark form organisations, and via their organisations...... immigrant women´s organisations, this paper aims to explore patterns of networking among these women, and the level and nature of their interaction with other organisations and societal institutions....

  1. APPLYING ARTIFICIAL INTELLIGENCE TECHNIQUES TO HUMAN-COMPUTER INTERFACES

    DEFF Research Database (Denmark)

    Sonnenwald, Diane H.

    1988-01-01

    A description is given of UIMS (User Interface Management System), a system using a variety of artificial intelligence techniques to build knowledge-based user interfaces combining functionality and information from a variety of computer systems that maintain, test, and configure customer telephone...... and data networks. Three artificial intelligence (AI) techniques used in UIMS are discussed, namely, frame representation, object-oriented programming languages, and rule-based systems. The UIMS architecture is presented, and the structure of the UIMS is explained in terms of the AI techniques....

  2. Applying decision-making techniques to Civil Engineering Projects

    Directory of Open Access Journals (Sweden)

    Fam F. Abdel-malak

    2017-12-01

    Full Text Available Multi-Criteria Decision-Making (MCDM techniques are found to be useful tools in project managers’ hands to overcome decision-making (DM problems in Civil Engineering Projects (CEPs. The main contribution of this paper includes selecting and studying the popular MCDM techniques that uses different and wide ranges of data types in CEPs. A detailed study including advantages and pitfalls of using the Analytic Hierarchy Process (AHP and Fuzzy Technique for Order of Preference by Similarity to Ideal Solution (Fuzzy TOPSIS is introduced. Those two techniques are selected for the purpose of forming a package that covers most available data types in CEPs. The results indicated that AHP has a structure which simplifies complicated problems, while Fuzzy TOPSIS uses the advantages of linguistic variables to solve the issue of undocumented data and ill-defined problems. Furthermore, AHP is a simple technique that depends on pairwise comparisons of factors and natural attributes, beside it is preferable for widely spread hierarchies. On the other hand, Fuzzy TOPSIS needs more information but works well for the one-tier decision tree as well as it shows more flexibility to work in fuzzy environments. The two techniques have the facility to be integrated and combined in a new module to support most of the decisions required in CEPs. Keywords: Decision-making, AHP, Fuzzy TOPSIS, CBA, Civil Engineering Projects

  3. Object oriented programming techniques applied to device access and control

    International Nuclear Information System (INIS)

    Goetz, A.; Klotz, W.D.; Meyer, J.

    1992-01-01

    In this paper a model, called the device server model, has been presented for solving the problem of device access and control faced by all control systems. Object Oriented Programming techniques were used to achieve a powerful yet flexible solution. The model provides a solution to the problem which hides device dependancies. It defines a software framework which has to be respected by implementors of device classes - this is very useful for developing groupware. The decision to implement remote access in the root class means that device servers can be easily integrated in a distributed control system. A lot of the advantages and features of the device server model are due to the adoption of OOP techniques. The main conclusion that can be drawn from this paper is that 1. the device access and control problem is adapted to being solved with OOP techniques, 2. OOP techniques offer a distinct advantage over traditional programming techniques for solving the device access problem. (J.P.N.)

  4. Rare event techniques applied in the Rasmussen study

    International Nuclear Information System (INIS)

    Vesely, W.E.

    1977-01-01

    The Rasmussen Study estimated public risks from commercial nuclear power plant accidents, and therefore the statistics of rare events had to be treated. Two types of rare events were specifically handled, those rare events which were probabilistically rare events and those which were statistically rare events. Four techniques were used to estimate probabilities of rare events. These techniques were aggregating data samples, discretizing ''continuous'' events, extrapolating from minor to catastrophic severities, and decomposing events using event trees and fault trees. In aggregating or combining data the goal was to enlarge the data sample so that the rare event was no longer rare, i.e., so that the enlarged data sample contained one or more occurrences of the event of interest. This aggregation gave rise to random variable treatments of failure rates, occurrence frequencies, and other characteristics estimated from data. This random variable treatment can be interpreted as being comparable to an empirical Bayes technique or a Bayesian technique. In the discretizing event technique, events of a detailed nature were grouped together into a grosser event for purposes of analysis as well as for data collection. The treatment of data characteristics as random variables helped to account for the uncertainties arising from this discretizing. In the severity extrapolation technique a severity variable was associated with each event occurrence for the purpose of predicting probabilities of catastrophic occurrences. Tail behaviors of distributions therefore needed to be considered. Finally, event trees and fault trees were used to express accident occurrences and system failures in terms of more basic events for which data existed. Common mode failures and general dependencies therefore needed to be treated. 2 figures

  5. Bioremediation techniques applied to aqueous media contaminated with mercury.

    Science.gov (United States)

    Velásquez-Riaño, Möritz; Benavides-Otaya, Holman D

    2016-12-01

    In recent years, the environmental and human health impacts of mercury contamination have driven the search for alternative, eco-efficient techniques different from the traditional physicochemical methods for treating this metal. One of these alternative processes is bioremediation. A comprehensive analysis of the different variables that can affect this process is presented. It focuses on determining the effectiveness of different techniques of bioremediation, with a specific consideration of three variables: the removal percentage, time needed for bioremediation and initial concentration of mercury to be treated in an aqueous medium.

  6. X-diffraction technique applied for nano system metrology

    International Nuclear Information System (INIS)

    Kuznetsov, Alexei Yu.; Machado, Rogerio; Robertis, Eveline de; Campos, Andrea P.C.; Archanjo, Braulio S.; Gomes, Lincoln S.; Achete, Carlos A.

    2009-01-01

    The application of nano materials are fast growing in all industrial sectors, with a strong necessity in nano metrology and normalizing in the nano material area. The great potential of the X-ray diffraction technique in this field is illustrated at the example of metals, metal oxides and pharmaceuticals

  7. The ordering operator technique applied to open systems

    International Nuclear Information System (INIS)

    Pedrosa, I.A.; Baseia, B.

    1982-01-01

    A normal ordering technique and the coherent representation are used to discribe the time evolution of an open system of a single oscillator, linearly coupled with an infinite number of reservoir oscillators and it is shown how to include the dissipation and get the exponential decay. (Author) [pt

  8. Ion backscattering techniques applied in materials science research

    International Nuclear Information System (INIS)

    Sood, D.K.

    1978-01-01

    The applications of Ion Backscattering Technique (IBT) to material analysis have expanded rapidly during the last decade. It is now regarded as an analysis tool indispensable for a versatile materials research program. The technique consists of simply shooting a beam of monoenergetic ions (usually 4 He + ions at about 2 MeV) onto a target, and measuring their energy distribution after backscattering at a fixed angle. Simple Rutherford scattering analysis of the backscattered ion spectrum yields information on the mass, the absolute amount and the depth profile of elements present upto a few microns of the target surface. The technique is nondestructive, quick, quantitative and the only known method of analysis which gives quantitative results without recourse to calibration standards. Its major limitations are the inability to separate elements of similar mass and a complete absence of chemical-binding information. A typical experimental set up and spectrum analysis have been described. Examples, some of them based on the work at the Bhabha Atomic Research Centre, Bombay, have been given to illustrate the applications of this technique to semiconductor technology, thin film materials science and nuclear energy materials. Limitations of IBT have been illustrated and a few remedies to partly overcome these limitations are presented. (auth.)

  9. Eddy current technique applied to automated tube profilometry

    International Nuclear Information System (INIS)

    Dobbeni, D.; Melsen, C. van

    1982-01-01

    The use of eddy current methods in the first totally automated pre-service inspection of the internal diameter of PWR steam generator tubes is described. The technique was developed at Laborelec, the Belgian Laboratory of the Electricity Supply Industry. Details are given of the data acquisition system and of the automated manipulator. Representative tube profiles are illustrated. (U.K.)

  10. Flash radiographic technique applied to fuel injector sprays

    International Nuclear Information System (INIS)

    Vantine, H.C.

    1977-01-01

    A flash radiographic technique, using 50 ns exposure times, was used to study the pattern and density distribution of a fuel injector spray. The experimental apparatus and method are described. An 85 kVp flash x-ray generator, designed and fabricated at the Lawrence Livermore Laboratory, is utilized. Radiographic images, recorded on standard x-ray films, are digitized and computer processed

  11. Machine-learning techniques applied to antibacterial drug discovery.

    Science.gov (United States)

    Durrant, Jacob D; Amaro, Rommie E

    2015-01-01

    The emergence of drug-resistant bacteria threatens to revert humanity back to the preantibiotic era. Even now, multidrug-resistant bacterial infections annually result in millions of hospital days, billions in healthcare costs, and, most importantly, tens of thousands of lives lost. As many pharmaceutical companies have abandoned antibiotic development in search of more lucrative therapeutics, academic researchers are uniquely positioned to fill the pipeline. Traditional high-throughput screens and lead-optimization efforts are expensive and labor intensive. Computer-aided drug-discovery techniques, which are cheaper and faster, can accelerate the identification of novel antibiotics, leading to improved hit rates and faster transitions to preclinical and clinical testing. The current review describes two machine-learning techniques, neural networks and decision trees, that have been used to identify experimentally validated antibiotics. We conclude by describing the future directions of this exciting field. © 2015 John Wiley & Sons A/S.

  12. Positron Plasma Control Techniques Applied to Studies of Cold Antihydrogen

    CERN Document Server

    Funakoshi, Ryo

    2003-01-01

    In the year 2002, two experiments at CERN succeeded in producing cold antihydrogen atoms, first ATHENA and subsequently ATRAP. Following on these results, it is now feasible to use antihydrogen to study the properties of antimatter. In the ATHENA experiment, the cold antihydrogen atoms are produced by mixing large amounts of antiprotons and positrons in a nested Penning trap. The complicated behaviors of the charged particles are controlled and monitored by plasma manipulation techniques. The antihydrogen events are studied using position sensitive detectors and the evidence of production of antihydrogen atoms is separated out with the help of analysis software. This thesis covers the first production of cold antihydrogen in the first section as well as the further studies of cold antihydrogen performed by using the plasma control techniques in the second section.

  13. Ion beam analysis techniques applied to large scale pollution studies

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, D D; Bailey, G; Martin, J; Garton, D; Noorman, H; Stelcer, E; Johnson, P [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia)

    1994-12-31

    Ion Beam Analysis (IBA) techniques are ideally suited to analyse the thousands of filter papers a year that may originate from a large scale aerosol sampling network. They are fast multi-elemental and, for the most part, non-destructive so other analytical methods such as neutron activation and ion chromatography can be performed afterwards. ANSTO in collaboration with the NSW EPA, Pacific Power and the Universities of NSW and Macquarie has established a large area fine aerosol sampling network covering nearly 80,000 square kilometres of NSW with 25 fine particle samplers. This network known as ASP was funded by the Energy Research and Development Corporation (ERDC) and commenced sampling on 1 July 1991. The cyclone sampler at each site has a 2.5 {mu}m particle diameter cut off and runs for 24 hours every Sunday and Wednesday using one Gillman 25mm diameter stretched Teflon filter for each day. These filters are ideal targets for ion beam analysis work. Currently ANSTO receives 300 filters per month from this network for analysis using its accelerator based ion beam techniques on the 3 MV Van de Graaff accelerator. One week a month of accelerator time is dedicated to this analysis. Four simultaneous accelerator based IBA techniques are used at ANSTO, to analyse for the following 24 elements: H, C, N, O, F, Na, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Cu, Ni, Co, Zn, Br and Pb. The IBA techniques were proved invaluable in identifying sources of fine particles and their spatial and seasonal variations accross the large area sampled by the ASP network. 3 figs.

  14. Ion beam analysis techniques applied to large scale pollution studies

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, D.D.; Bailey, G.; Martin, J.; Garton, D.; Noorman, H.; Stelcer, E.; Johnson, P. [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia)

    1993-12-31

    Ion Beam Analysis (IBA) techniques are ideally suited to analyse the thousands of filter papers a year that may originate from a large scale aerosol sampling network. They are fast multi-elemental and, for the most part, non-destructive so other analytical methods such as neutron activation and ion chromatography can be performed afterwards. ANSTO in collaboration with the NSW EPA, Pacific Power and the Universities of NSW and Macquarie has established a large area fine aerosol sampling network covering nearly 80,000 square kilometres of NSW with 25 fine particle samplers. This network known as ASP was funded by the Energy Research and Development Corporation (ERDC) and commenced sampling on 1 July 1991. The cyclone sampler at each site has a 2.5 {mu}m particle diameter cut off and runs for 24 hours every Sunday and Wednesday using one Gillman 25mm diameter stretched Teflon filter for each day. These filters are ideal targets for ion beam analysis work. Currently ANSTO receives 300 filters per month from this network for analysis using its accelerator based ion beam techniques on the 3 MV Van de Graaff accelerator. One week a month of accelerator time is dedicated to this analysis. Four simultaneous accelerator based IBA techniques are used at ANSTO, to analyse for the following 24 elements: H, C, N, O, F, Na, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Cu, Ni, Co, Zn, Br and Pb. The IBA techniques were proved invaluable in identifying sources of fine particles and their spatial and seasonal variations accross the large area sampled by the ASP network. 3 figs.

  15. Rethinking capacity building for knowledge mobilisation: developing multilevel capabilities in healthcare organisations.

    Science.gov (United States)

    Kislov, Roman; Waterman, Heather; Harvey, Gill; Boaden, Ruth

    2014-11-15

    Knowledge mobilisation in healthcare organisations is often carried out through relatively short-term projects dependent on limited funding, which raises concerns about the long-term sustainability of implementation and improvement. It is becoming increasingly recognised that the translation of research evidence into practice has to be supported by developing the internal capacity of healthcare organisations to engage with and apply research. This process can be supported by external knowledge mobilisation initiatives represented, for instance, by professional associations, collaborative research partnerships and implementation networks. This conceptual paper uses empirical and theoretical literature on organisational learning and dynamic capabilities to enhance our understanding of intentional capacity building for knowledge mobilisation in healthcare organisations. The discussion is structured around the following three themes: (1) defining and classifying capacity building for knowledge mobilisation; (2) mechanisms of capability development in organisational context; and (3) individual, group and organisational levels of capability development. Capacity building is presented as a practice-based process of developing multiple skills, or capabilities, belonging to different knowledge domains and levels of complexity. It requires an integration of acquisitive learning, through which healthcare organisations acquire knowledge and skills from knowledge mobilisation experts, and experience-based learning, through which healthcare organisations adapt, absorb and modify their knowledge and capabilities through repeated practice. Although the starting point for capability development may be individual-, team- or organisation-centred, facilitation of the transitions between individual, group and organisational levels of learning within healthcare organisations will be needed. Any initiative designed to build capacity for knowledge mobilisation should consider the

  16. Enhanced nonlinear iterative techniques applied to a nonequilibrium plasma flow

    International Nuclear Information System (INIS)

    Knoll, D.A.

    1998-01-01

    The authors study the application of enhanced nonlinear iterative methods to the steady-state solution of a system of two-dimensional convection-diffusion-reaction partial differential equations that describe the partially ionized plasma flow in the boundary layer of a tokamak fusion reactor. This system of equations is characterized by multiple time and spatial scales and contains highly anisotropic transport coefficients due to a strong imposed magnetic field. They use Newton's method to linearize the nonlinear system of equations resulting from an implicit, finite volume discretization of the governing partial differential equations, on a staggered Cartesian mesh. The resulting linear systems are neither symmetric nor positive definite, and are poorly conditioned. Preconditioned Krylov iterative techniques are employed to solve these linear systems. They investigate both a modified and a matrix-free Newton-Krylov implementation, with the goal of reducing CPU cost associated with the numerical formation of the Jacobian. A combination of a damped iteration, mesh sequencing, and a pseudotransient continuation technique is used to enhance global nonlinear convergence and CPU efficiency. GMRES is employed as the Krylov method with incomplete lower-upper (ILU) factorization preconditioning. The goal is to construct a combination of nonlinear and linear iterative techniques for this complex physical problem that optimizes trade-offs between robustness, CPU time, memory requirements, and code complexity. It is shown that a mesh sequencing implementation provides significant CPU savings for fine grid calculations. Performance comparisons of modified Newton-Krylov and matrix-free Newton-Krylov algorithms will be presented

  17. Applying NISHIJIN historical textile technique for e-Textile.

    Science.gov (United States)

    Kuroda, Tomohiro; Hirano, Kikuo; Sugimura, Kazushige; Adachi, Satoshi; Igarashi, Hidetsugu; Ueshima, Kazuo; Nakamura, Hideo; Nambu, Masayuki; Doi, Takahiro

    2013-01-01

    The e-Textile is the key technology for continuous ambient health monitoring to increase quality of life of patients with chronic diseases. The authors introduce techniques of Japanese historical textile, NISHIJIN, which illustrate almost any pattern from one continuous yarn within the machine weaving process, which is suitable for mixed flow production. Thus, NISHIJIN is suitable for e-Textile production, which requires rapid prototyping and mass production of very complicated patterns. The authors prototyped and evaluated a few vests to take twelve-lead electrocardiogram. The result tells that the prototypes obtains electrocardiogram, which is good enough for diagnosis.

  18. Applying Supervised Opinion Mining Techniques on Online User Reviews

    Directory of Open Access Journals (Sweden)

    Ion SMEUREANU

    2012-01-01

    Full Text Available In recent years, the spectacular development of web technologies, lead to an enormous quantity of user generated information in online systems. This large amount of information on web platforms make them viable for use as data sources, in applications based on opinion mining and sentiment analysis. The paper proposes an algorithm for detecting sentiments on movie user reviews, based on naive Bayes classifier. We make an analysis of the opinion mining domain, techniques used in sentiment analysis and its applicability. We implemented the proposed algorithm and we tested its performance, and suggested directions of development.

  19. Neutron activation: an invaluable technique for teaching applied radiation

    International Nuclear Information System (INIS)

    Trainer, Matthew

    2002-01-01

    This experiment introduces students to the important method of neutron activation. A sample of aluminium was irradiated with neutrons from an isotropic 241 Am-Be source. Using γ-ray spectroscopy, two radionuclide products were identified as 27 Mg and 28 Al. Applying a cadmium cut-off filter and an optimum irradiation time of 45 min, the half-life of 27 Mg was determined as 9.46±0.50 min. The half-life of the 28 Al radionuclide was determined as 2.28±0.10 min using a polythene moderator and an optimum irradiation time of 10 min. (author)

  20. Compressed Sensing Techniques Applied to Ultrasonic Imaging of Cargo Containers

    Directory of Open Access Journals (Sweden)

    Yuri Álvarez López

    2017-01-01

    Full Text Available One of the key issues in the fight against the smuggling of goods has been the development of scanners for cargo inspection. X-ray-based radiographic system scanners are the most developed sensing modality. However, they are costly and use bulky sources that emit hazardous, ionizing radiation. Aiming to improve the probability of threat detection, an ultrasonic-based technique, capable of detecting the footprint of metallic containers or compartments concealed within the metallic structure of the inspected cargo, has been proposed. The system consists of an array of acoustic transceivers that is attached to the metallic structure-under-inspection, creating a guided acoustic Lamb wave. Reflections due to discontinuities are detected in the images, provided by an imaging algorithm. Taking into consideration that the majority of those images are sparse, this contribution analyzes the application of Compressed Sensing (CS techniques in order to reduce the amount of measurements needed, thus achieving faster scanning, without compromising the detection capabilities of the system. A parametric study of the image quality, as a function of the samples needed in spatial and frequency domains, is presented, as well as the dependence on the sampling pattern. For this purpose, realistic cargo inspection scenarios have been simulated.

  1. Nuclear reactor vessel surface inspecting technique applying electric resistance probe

    International Nuclear Information System (INIS)

    Yamaguchi, T.; Enami, K.; Yoshioka, M.

    1975-01-01

    A new technique for inspecting the inner surface of the PWR type nuclear reactor vessel by use of an electric resistance probe is introduced, centering on a data processing system. This system is composed of a mini-computer, a system typewriter, an interface unit, a D-A converter and controller, and X-Y recorder and others. Its functions are judging flaws and making flaw detection maps. In order to judge flaws by flaw detection signals, three kinds of flaw judging methods have been developed. In case there is a flaw, its position and depth are calculated and listed on the system typewriter. The flaw detection maps are expressed in four kinds of modes and they are displayed on the X-Y recorder. (auth.)

  2. Neoliberal Optimism: Applying Market Techniques to Global Health.

    Science.gov (United States)

    Mei, Yuyang

    2017-01-01

    Global health and neoliberalism are becoming increasingly intertwined as organizations utilize markets and profit motives to solve the traditional problems of poverty and population health. I use field work conducted over 14 months in a global health technology company to explore how the promise of neoliberalism re-envisions humanitarian efforts. In this company's vaccine refrigerator project, staff members expect their investors and their market to allow them to achieve scale and develop accountability to their users in developing countries. However, the translation of neoliberal techniques to the global health sphere falls short of the ideal, as profits are meager and purchasing power remains with donor organizations. The continued optimism in market principles amidst such a non-ideal market reveals the tenacious ideological commitment to neoliberalism in these global health projects.

  3. Nonequilibrium Green function techniques applied to hot electron quantum transport

    International Nuclear Information System (INIS)

    Jauho, A.P.

    1989-01-01

    During the last few years considerable effort has been devoted to deriving quantum transport equations for semiconductors under extreme conditions (high electric fields, spatial quantization in one or two directions). Here we review the results obtained with nonequilibrium Green function techniques as formulated by Baym and Kadanoff, or by Keldysh. In particular, the following topics will be discussed: (i) Systematic approaches to reduce the transport equation governing the correlation function to a transport equation for the Wigner function; (ii) Approximations reducing the nonmarkovian quantum transport equation to a numerically tractable form, and results for model semiconductors; (iii) Recent progress in extending the formalism to inhomogeneous systems; and (iv) Nonequilibrium screening. In all sections we try to direct the reader's attention to points where the present understanding is (at best) incomplete, and indicate possible lines for future work. (orig.)

  4. Active Learning Techniques Applied to an Interdisciplinary Mineral Resources Course.

    Science.gov (United States)

    Aird, H. M.

    2015-12-01

    An interdisciplinary active learning course was introduced at the University of Puget Sound entitled 'Mineral Resources and the Environment'. Various formative assessment and active learning techniques that have been effective in other courses were adapted and implemented to improve student learning, increase retention and broaden knowledge and understanding of course material. This was an elective course targeted towards upper-level undergraduate geology and environmental majors. The course provided an introduction to the mineral resources industry, discussing geological, environmental, societal and economic aspects, legislation and the processes involved in exploration, extraction, processing, reclamation/remediation and recycling of products. Lectures and associated weekly labs were linked in subject matter; relevant readings from the recent scientific literature were assigned and discussed in the second lecture of the week. Peer-based learning was facilitated through weekly reading assignments with peer-led discussions and through group research projects, in addition to in-class exercises such as debates. Writing and research skills were developed through student groups designing, carrying out and reporting on their own semester-long research projects around the lasting effects of the historical Ruston Smelter on the biology and water systems of Tacoma. The writing of their mini grant proposals and final project reports was carried out in stages to allow for feedback before the deadline. Speakers from industry were invited to share their specialist knowledge as guest lecturers, and students were encouraged to interact with them, with a view to employment opportunities. Formative assessment techniques included jigsaw exercises, gallery walks, placemat surveys, think pair share and take-home point summaries. Summative assessment included discussion leadership, exams, homeworks, group projects, in-class exercises, field trips, and pre-discussion reading exercises

  5. Quantitative Portfolio Optimization Techniques Applied to the Brazilian Stock Market

    Directory of Open Access Journals (Sweden)

    André Alves Portela Santos

    2012-09-01

    Full Text Available In this paper we assess the out-of-sample performance of two alternative quantitative portfolio optimization techniques - mean-variance and minimum variance optimization – and compare their performance with respect to a naive 1/N (or equally-weighted portfolio and also to the market portfolio given by the Ibovespa. We focus on short selling-constrained portfolios and consider alternative estimators for the covariance matrices: sample covariance matrix, RiskMetrics, and three covariance estimators proposed by Ledoit and Wolf (2003, Ledoit and Wolf (2004a and Ledoit and Wolf (2004b. Taking into account alternative portfolio re-balancing frequencies, we compute out-of-sample performance statistics which indicate that the quantitative approaches delivered improved results in terms of lower portfolio volatility and better risk-adjusted returns. Moreover, the use of more sophisticated estimators for the covariance matrix generated optimal portfolios with lower turnover over time.

  6. Considerations in applying on-line IC techniques to BWR's

    International Nuclear Information System (INIS)

    Kaleda, R.J.

    1992-01-01

    Ion-Chromatography (IC) has moved from its traditional role as a laboratory analytical tool to a real time, dynamic, on-line measurement device to follow ppb and sub-ppb concentrations of deleterious impurities in nuclear power plants. Electric Power Research Institute (EPRI), individual utilities, and industry all have played significant roles in effecting the transition. This paper highlights considerations and the evolution in current on-line Ion Chromatography systems. The first applications of on-line techniques were demonstrated by General Electric (GE) under EPRI sponsorship at Rancho Seco (1980), Calvert Cliffs, and McGuire nuclear units. The primary use was for diagnostic purposes. Today the on-line IC applications have been expanded to include process control and routine plant monitoring. Current on-line IC's are innovative in design, promote operational simplicity, are modular for simplified maintenance and repair, and use field-proven components which enhance reliability. Conductivity detection with electronic or chemical suppression and spectrometric detection techniques are intermixed in applications. Remote multi-point sample systems have addressed memory effects. Early applications measured ionic species in the part per billion range. Today reliable part per trillion measurements are common for on-line systems. Current systems are meeting the challenge of EPRI guideline requirements. Today's on-line IC's, with programmed sampling systems, monitor fluid streams throughout a power plant, supplying data that can be trended, stored and retrieved easily. The on-line IC has come of age. Many technical challenges were overcome to achieve today's IC

  7. SPI Trend Analysis of New Zealand Applying the ITA Technique

    Directory of Open Access Journals (Sweden)

    Tommaso Caloiero

    2018-03-01

    Full Text Available A natural temporary imbalance of water availability, consisting of persistent lower-than-average or higher-than-average precipitation, can cause extreme dry and wet conditions that adversely impact agricultural yields, water resources, infrastructure, and human systems. In this study, dry and wet periods in New Zealand were expressed using the Standardized Precipitation Index (SPI. First, both the short term (3 and 6 months and the long term (12 and 24 months SPI were estimated, and then, possible trends in the SPI values were detected by means of a new graphical technique, the Innovative Trend Analysis (ITA, which allows the trend identification of the low, medium, and high values of a series. Results show that, in every area currently subject to drought, an increase in this phenomenon can be expected. Specifically, the results of this paper highlight that agricultural regions on the eastern side of the South Island, as well as the north-eastern regions of the North Island, are the most consistently vulnerable areas. In fact, in these regions, the trend analysis mainly showed a general reduction in all the values of the SPI: that is, a tendency toward heavier droughts and weaker wet periods.

  8. Digital prototyping technique applied for redesigning plastic products

    Science.gov (United States)

    Pop, A.; Andrei, A.

    2015-11-01

    After products are on the market for some time, they often need to be redesigned to meet new market requirements. New products are generally derived from similar but outdated products. Redesigning a product is an important part of the production and development process. The purpose of this paper is to show that using modern technology, like Digital Prototyping in industry is an effective way to produce new products. This paper tries to demonstrate and highlight the effectiveness of the concept of Digital Prototyping, both to reduce the design time of a new product, but also the costs required for implementing this step. The results of this paper show that using Digital Prototyping techniques in designing a new product from an existing one available on the market mould offers a significantly manufacturing time and cost reduction. The ability to simulate and test a new product with modern CAD-CAM programs in all aspects of production (designing of the 3D model, simulation of the structural resistance, analysis of the injection process and beautification) offers a helpful tool for engineers. The whole process can be realised by one skilled engineer very fast and effective.

  9. Acoustic Emission Technique Applied in Textiles Mechanical Characterization

    Directory of Open Access Journals (Sweden)

    Rios-Soberanis Carlos Rolando

    2017-01-01

    Full Text Available The common textile architecture/geometry are woven, braided, knitted, stitch boded, and Z-pinned. Fibres in textile form exhibit good out-of-plane properties and good fatigue and impact resistance, additionally, they have better dimensional stability and conformability. Besides the nature of the textile, the architecture has a great role in the mechanical behaviour and mechanisms of damage in textiles, therefore damage mechanisms and mechanical performance in structural applications textiles have been a major concern. Mechanical damage occurs to a large extent during the service lifetime consequently it is vital to understand the material mechanical behaviour by identifying its mechanisms of failure such as onset of damage, crack generation and propagation. In this work, textiles of different architecture were used to manufacture epoxy based composites in order to study failure events under tensile load by using acoustic emission technique which is a powerful characterization tool due to its link between AE data and fracture mechanics, which makes this relation a very useful from the engineering point of view.

  10. A Kalman filter technique applied for medical image reconstruction

    International Nuclear Information System (INIS)

    Goliaei, S.; Ghorshi, S.; Manzuri, M. T.; Mortazavi, M.

    2011-01-01

    Medical images contain information about vital organic tissues inside of human body and are widely used for diagnoses of disease or for surgical purposes. Image reconstruction is essential for medical images for some applications such as suppression of noise or de-blurring the image in order to provide images with better quality and contrast. Due to vital rule of image reconstruction in medical sciences the corresponding algorithms with better efficiency and higher speed is desirable. Most algorithms in image reconstruction are operated on frequency domain such as the most popular one known as filtered back projection. In this paper we introduce a Kalman filter technique which is operated in time domain for medical image reconstruction. Results indicated that as the number of projection increases in both normal collected ray sum and the collected ray sum corrupted by noise the quality of reconstructed image becomes better in terms of contract and transparency. It is also seen that as the number of projection increases the error index decreases.

  11. Advanced Gradient Based Optimization Techniques Applied on Sheet Metal Forming

    International Nuclear Information System (INIS)

    Endelt, Benny; Nielsen, Karl Brian

    2005-01-01

    The computational-costs for finite element simulations of general sheet metal forming processes are considerable, especially measured in time. In combination with optimization, the performance of the optimization algorithm is crucial for the overall performance of the system, i.e. the optimization algorithm should gain as much information about the system in each iteration as possible. Least-square formulation of the object function is widely applied for solution of inverse problems, due to the superior performance of this formulation.In this work focus will be on small problems which are defined as problems with less than 1000 design parameters; as the majority of real life optimization and inverse problems, represented in literature, can be characterized as small problems, typically with less than 20 design parameters.We will show that the least square formulation is well suited for two classes of inverse problems; identification of constitutive parameters and process optimization.The scalability and robustness of the approach are illustrated through a number of process optimizations and inverse material characterization problems; tube hydro forming, two step hydro forming, flexible aluminum tubes, inverse identification of material parameters

  12. Applying data mining techniques to improve diagnosis in neonatal jaundice

    Directory of Open Access Journals (Sweden)

    Ferreira Duarte

    2012-12-01

    Full Text Available Abstract Background Hyperbilirubinemia is emerging as an increasingly common problem in newborns due to a decreasing hospital length of stay after birth. Jaundice is the most common disease of the newborn and although being benign in most cases it can lead to severe neurological consequences if poorly evaluated. In different areas of medicine, data mining has contributed to improve the results obtained with other methodologies. Hence, the aim of this study was to improve the diagnosis of neonatal jaundice with the application of data mining techniques. Methods This study followed the different phases of the Cross Industry Standard Process for Data Mining model as its methodology. This observational study was performed at the Obstetrics Department of a central hospital (Centro Hospitalar Tâmega e Sousa – EPE, from February to March of 2011. A total of 227 healthy newborn infants with 35 or more weeks of gestation were enrolled in the study. Over 70 variables were collected and analyzed. Also, transcutaneous bilirubin levels were measured from birth to hospital discharge with maximum time intervals of 8 hours between measurements, using a noninvasive bilirubinometer. Different attribute subsets were used to train and test classification models using algorithms included in Weka data mining software, such as decision trees (J48 and neural networks (multilayer perceptron. The accuracy results were compared with the traditional methods for prediction of hyperbilirubinemia. Results The application of different classification algorithms to the collected data allowed predicting subsequent hyperbilirubinemia with high accuracy. In particular, at 24 hours of life of newborns, the accuracy for the prediction of hyperbilirubinemia was 89%. The best results were obtained using the following algorithms: naive Bayes, multilayer perceptron and simple logistic. Conclusions The findings of our study sustain that, new approaches, such as data mining, may support

  13. Applying perceptual and adaptive learning techniques for teaching introductory histopathology

    Directory of Open Access Journals (Sweden)

    Sally Krasne

    2013-01-01

    Full Text Available Background: Medical students are expected to master the ability to interpret histopathologic images, a difficult and time-consuming process. A major problem is the issue of transferring information learned from one example of a particular pathology to a new example. Recent advances in cognitive science have identified new approaches to address this problem. Methods: We adapted a new approach for enhancing pattern recognition of basic pathologic processes in skin histopathology images that utilizes perceptual learning techniques, allowing learners to see relevant structure in novel cases along with adaptive learning algorithms that space and sequence different categories (e.g. diagnoses that appear during a learning session based on each learner′s accuracy and response time (RT. We developed a perceptual and adaptive learning module (PALM that utilized 261 unique images of cell injury, inflammation, neoplasia, or normal histology at low and high magnification. Accuracy and RT were tracked and integrated into a "Score" that reflected students rapid recognition of the pathologies and pre- and post-tests were given to assess the effectiveness. Results: Accuracy, RT and Scores significantly improved from the pre- to post-test with Scores showing much greater improvement than accuracy alone. Delayed post-tests with previously unseen cases, given after 6-7 weeks, showed a decline in accuracy relative to the post-test for 1 st -year students, but not significantly so for 2 nd -year students. However, the delayed post-test scores maintained a significant and large improvement relative to those of the pre-test for both 1 st and 2 nd year students suggesting good retention of pattern recognition. Student evaluations were very favorable. Conclusion: A web-based learning module based on the principles of cognitive science showed an evidence for improved recognition of histopathology patterns by medical students.

  14. Semantic Data And Visualization Techniques Applied To Geologic Field Mapping

    Science.gov (United States)

    Houser, P. I. Q.; Royo-Leon, M.; Munoz, R.; Estrada, E.; Villanueva-Rosales, N.; Pennington, D. D.

    2015-12-01

    Geologic field mapping involves the use of technology before, during, and after visiting a site. Geologists utilize hardware such as Global Positioning Systems (GPS) connected to mobile computing platforms such as tablets that include software such as ESRI's ArcPad and other software to produce maps and figures for a final analysis and report. Hand written field notes contain important information and drawings or sketches of specific areas within the field study. Our goal is to collect and geo-tag final and raw field data into a cyber-infrastructure environment with an ontology that allows for large data processing, visualization, sharing, and searching, aiding in connecting field research with prior research in the same area and/or aid with experiment replication. Online searches of a specific field area return results such as weather data from NOAA and QuakeML seismic data from USGS. These results that can then be saved to a field mobile device and searched while in the field where there is no Internet connection. To accomplish this we created the GeoField ontology service using the Web Ontology Language (OWL) and Protégé software. Advanced queries on the dataset can be made using reasoning capabilities can be supported that go beyond a standard database service. These improvements include the automated discovery of data relevant to a specific field site and visualization techniques aimed at enhancing analysis and collaboration while in the field by draping data over mobile views of the site using augmented reality. A case study is being performed at University of Texas at El Paso's Indio Mountains Research Station located near Van Horn, Texas, an active multi-disciplinary field study site. The user can interactively move the camera around the study site and view their data digitally. Geologist's can check their data against the site in real-time and improve collaboration with another person as both parties have the same interactive view of the data.

  15. Should we mobilise critically ill patients? A review.

    LENUS (Irish Health Repository)

    O'Connor, Enda D

    2009-12-01

    Neuromuscular weakness, a frequent complication of prolonged bed rest and critical illness, is associated with morbidity and mortality. Mobilisation physiotherapy has widespread application in patients hospitalised with non-critical illness.

  16. Discord in the gender harmony: Mobilising femininities at work

    OpenAIRE

    Carr, Melissa; Kelan, Elisabeth K.

    2017-01-01

    This article seeks to aid our understanding of gendered inclusion by looking at how femininities are mobilised at work. Whilst within the popular press there is a growing neo-liberal discourse about women supporting other women in organisations, little consideration has been given to men’s reactions to women aligning with each other, in other words, women mobilising femininities. Furthermore, whilst studies of doing gender have considered this from an individual viewpoint, we are unclear abou...

  17. Social Media, Deliberative Democracy and Social Mobilisation

    DEFF Research Database (Denmark)

    Nielsen, Jørgen Lerche; Bodington, Malene; Lerche, Søren

    Over the past 20 years, researchers have studied how the Internet frames deliberative processes. What is needed to create a framework for dialogue & engagement, & how can the Internet be used to create & support social communities? (Castells 2001, Dyson 1997, Rheingold 1993). However, these appro......Over the past 20 years, researchers have studied how the Internet frames deliberative processes. What is needed to create a framework for dialogue & engagement, & how can the Internet be used to create & support social communities? (Castells 2001, Dyson 1997, Rheingold 1993). However......, these approaches have all taken a normative & meta-theoretical approach to the subject & are rarely grounded in empirical research. Much has been written about using social media in a rationally, purpose-driven or strategic way, relating it to corporations, political organisations, and the latest in relation...... to the Obama presidential campaign in 2008, where deliberative features were successfully used to mobilise and organise 2 millions activists through his social network, Mybo.com. However, very little literature addresses the deliberative processes, nor does much past research build on cases that have...

  18. Kinematic real-time feedback is more effective than traditional teaching method in learning ankle joint mobilisation: a randomised controlled trial.

    Science.gov (United States)

    González-Sánchez, Manuel; Ruiz-Muñoz, Maria; Ávila-Bolívar, Ana Belén; Cuesta-Vargas, Antonio I

    2016-10-06

    To analyse the effect of real-time kinematic feedback (KRTF) when learning two ankle joint mobilisation techniques comparing the results with the traditional teaching method. Double-blind randomized trial. Faculty of Health Sciences. undergraduate students with no experience in manual therapy. Each student practised intensely for 90 min (45 min for each mobilisation) according to the random methodology assigned (G1: traditional method group and G2: KRTF group). G1: an expert professor supervising the student's practice, the professorstudent ratio was 1:8. G2: placed in front of a station where, while they performed the manoeuvre, they received a KRTF on a laptop. total time of mobilisation, time to reach maximum amplitude, maximum angular displacement in the three axes, maximum and average velocity to reach the maximum angular displacement, average velocity during the mobilisation. Among the pre-post intervention measurements, there were significant differences within the two groups for all outcome variables, however, G2 (KRTF) achieved significantly greater improvements in kinematic parameters for the two mobilisations (significant increase in displacement, velocity and significant reduction in the mobilisations runtime) than G1. Ankle plantar flexion: G1's measurement stability (post-intervention) ranged between 0.491 and 0.687, while G2's measurement stability ranged between 0.899 and 0.984. Ankle dorsal flexion mobilisation: G1 the measurement stability (post-intervention) ranged from 0.543 and 0.684 while G2 ranged between 0.899 and 0.974. KRTF was proven to be more effective tool than traditional teaching method in the teaching - learning process of two joint mobilisation techniques. NCT02504710.

  19. Applying BI Techniques To Improve Decision Making And Provide Knowledge Based Management

    Directory of Open Access Journals (Sweden)

    Alexandra Maria Ioana FLOREA

    2015-07-01

    Full Text Available The paper focuses on BI techniques and especially data mining algorithms that can support and improve the decision making process, with applications within the financial sector. We consider the data mining techniques to be more efficient and thus we applied several techniques, supervised and unsupervised learning algorithms The case study in which these algorithms have been implemented regards the activity of a banking institution, with focus on the management of lending activities.

  20. Dielectric spectroscopy technique applied to study the behaviour of irradiated polymer

    International Nuclear Information System (INIS)

    Saoud, R.; Soualmia, A.; Guerbi, C.A.; Benrekaa, N.

    2006-01-01

    Relaxation spectroscopy provides an excellent method for the study of motional processes in materials and has been widely applied to macromolecules and polymers. The technique is potentially of most interest when applied to irradiated systems. Application to the study of the structure beam-irradiated Teflon is thus an outstanding opportunity for the dielectric relaxation technique, particularly as this material exhibits clamping problems when subjected to dynamic mechanical relaxation studies. A very wide frequency range is necessary to resolve dipolar effects. In this paper, we discuss some significant results about the behavior and the modification of the structure of Teflon submitted to weak energy radiations

  1. Database 'catalogue of techniques applied to materials and products of nuclear engineering'

    International Nuclear Information System (INIS)

    Lebedeva, E.E.; Golovanov, V.N.; Podkopayeva, I.A.; Temnoyeva, T.A.

    2002-01-01

    The database 'Catalogue of techniques applied to materials and products of nuclear engineering' (IS MERI) was developed to provide informational support for SSC RF RIAR and other enterprises in scientific investigations. This database contains information on the techniques used at RF Minatom enterprises for reactor material properties investigation. The main purpose of this system consists in the assessment of the current status of the reactor material science experimental base for the further planning of experimental activities and methodical support improvement. (author)

  2. Strategies and techniques of communication and public relations applied to non-profit sector

    Directory of Open Access Journals (Sweden)

    Ioana – Julieta Josan

    2010-05-01

    Full Text Available The aim of this paper is to summarize the strategies and techniques of communication and public relations applied to non-profit sector.The approach of the paper is to identify the most appropriate strategies and techniques that non-profit sector can use to accomplish its objectives, to highlight specific differences between the strategies and techniques of the profit and non-profit sectors and to identify potential communication and public relations actions in order to increase visibility among target audience, create brand awareness and to change into positive brand sentiment the target perception about the non-profit sector.

  3. Improving skill development: an exploratory study comparing a philosophical and an applied ethical analysis technique

    Science.gov (United States)

    Al-Saggaf, Yeslam; Burmeister, Oliver K.

    2012-09-01

    This exploratory study compares and contrasts two types of critical thinking techniques; one is a philosophical and the other an applied ethical analysis technique. The two techniques analyse an ethically challenging situation involving ICT that a recent media article raised to demonstrate their ability to develop the ethical analysis skills of ICT students and professionals. In particular the skill development focused on includes: being able to recognise ethical challenges and formulate coherent responses; distancing oneself from subjective judgements; developing ethical literacy; identifying stakeholders; and communicating ethical decisions made, to name a few.

  4. English Language Teachers' Perceptions on Knowing and Applying Contemporary Language Teaching Techniques

    Science.gov (United States)

    Sucuoglu, Esen

    2017-01-01

    The aim of this study is to determine the perceptions of English language teachers teaching at a preparatory school in relation to their knowing and applying contemporary language teaching techniques in their lessons. An investigation was conducted of 21 English language teachers at a preparatory school in North Cyprus. The SPSS statistical…

  5. Improvement technique of sensitized HAZ by GTAW cladding applied to a BWR power plant

    International Nuclear Information System (INIS)

    Tujimura, Hiroshi; Tamai, Yasumasa; Furukawa, Hideyasu; Kurosawa, Kouichi; Chiba, Isao; Nomura, Keiichi.

    1995-01-01

    A SCC(Stress Corrosion Cracking)-resistant technique, in which the sleeve installed by expansion is melted by GTAW process without filler metal with outside water cooling, was developed. The technique was applied to ICM (In-Core Monitor) housings of a BWR power plant in 1993. The ICM housings of which materials are type 304 Stainless Steels are sensitized with high tensile residual stresses by welding to the RPV (Reactor Pressure Vessel). As the result, ICM housings have potential of SCC initiation. Therefore, the improvement technique resistant to SCC was needed. The technique can improve chemical composition of the housing inside and residual stresses of the housing outside at the same time. Sensitization of the housing inner surface area is eliminated by replacing low-carbon with proper-ferrite microstructure clad. High tensile residual stresses of housing outside surface area is improved into compressive side. Compressive stresses of outside surface are induced by thermal stresses which are caused by inside cladding with outside water cooling. The clad is required to be low-carbon metal with proper ferrite and not to have the new sensitized HAZ (Heat Affected Zone) on the surface by cladding. The effect of the technique was qualified by SCC test, chemical composition check, ferrite content measurement and residual stresses measurement etc. All equipment for remote application were developed and qualified, too. The technique was successfully applied to a BWR plant after sufficient training

  6. Statistical Techniques Used in Three Applied Linguistics Journals: "Language Learning,""Applied Linguistics" and "TESOL Quarterly," 1980-1986: Implications for Readers and Researchers.

    Science.gov (United States)

    Teleni, Vicki; Baldauf, Richard B., Jr.

    A study investigated the statistical techniques used by applied linguists and reported in three journals, "Language Learning,""Applied Linguistics," and "TESOL Quarterly," between 1980 and 1986. It was found that 47% of the published articles used statistical procedures. In these articles, 63% of the techniques used could be called basic, 28%…

  7. Electrokinetic mobilisation of toluene and chlorinated ethenes in low permeable soils

    Energy Technology Data Exchange (ETDEWEB)

    Middeldorp, P.; Sinke, A. [TNO Environment Energy and Process Innovation, Apeldoorn (Netherlands)

    2001-07-01

    An electrokinetic horizontal soil column setup was developed to study the effect of electric current on the mobilisation and biodegradation of organic pollutants in soil. Toluene and tetrachloroethene (PCE) were injected between the two electrodes in the center of the soil column and a DC current of 1 V/cm was applied. We observed a breakthrough of PCE and toluene at the cathode side after 8 days and 11 days respectively. This short experiment shows the possibility to enhance the mobility of non-ionic organic pollutants through electro-osmosis. (orig.)

  8. The impact of applying product-modelling techniques in configurator projects

    DEFF Research Database (Denmark)

    Hvam, Lars; Kristjansdottir, Katrin; Shafiee, Sara

    2018-01-01

    This paper aims to increase understanding of the impact of using product-modelling techniques to structure and formalise knowledge in configurator projects. Companies that provide customised products increasingly apply configurators in support of sales and design activities, reaping benefits...... that include shorter lead times, improved quality of specifications and products, and lower overall product costs. The design and implementation of configurators are a challenging task that calls for scientifically based modelling techniques to support the formal representation of configurator knowledge. Even...... the phenomenon model and information model are considered visually, (2) non-UML-based modelling techniques, in which only the phenomenon model is considered and (3) non-formal modelling techniques. This study analyses the impact to companies from increased availability of product knowledge and improved control...

  9. Applied potential tomography. A new noninvasive technique for measuring gastric emptying

    International Nuclear Information System (INIS)

    Avill, R.; Mangnall, Y.F.; Bird, N.C.; Brown, B.H.; Barber, D.C.; Seagar, A.D.; Johnson, A.G.; Read, N.W.

    1987-01-01

    Applied potential tomography is a new, noninvasive technique that yields sequential images of the resistivity of gastric contents after subjects have ingested a liquid or semisolid meal. This study validates the technique as a means of measuring gastric emptying. Experiments in vitro showed an excellent correlation between measurements of resistivity and either the square of the radius of a glass rod or the volume of water in a spherical balloon when both were placed in an oval tank containing saline. Altering the lateral position of the rod in the tank did not alter the values obtained. Images of abdominal resistivity were also directly correlated with the volume of air in a gastric balloon. Profiles of gastric emptying of liquid meals obtained using applied potential tomography were very similar to those obtained using scintigraphy or dye dilution techniques, provided that acid secretion was inhibited by cimetidine. Profiles of emptying of a mashed potato meal using applied potential tomography were also very similar to those obtained by scintigraphy. Measurements of the emptying of a liquid meal from the stomach were reproducible if acid secretion was inhibited by cimetidine. Thus, applied potential tomography is an accurate and reproducible method of measuring gastric emptying of liquids and particulate food. It is inexpensive, well tolerated, easy to use, and ideally suited for multiple studies in patients, even those who are pregnant

  10. Applied potential tomography. A new noninvasive technique for measuring gastric emptying

    Energy Technology Data Exchange (ETDEWEB)

    Avill, R.; Mangnall, Y.F.; Bird, N.C.; Brown, B.H.; Barber, D.C.; Seagar, A.D.; Johnson, A.G.; Read, N.W.

    1987-04-01

    Applied potential tomography is a new, noninvasive technique that yields sequential images of the resistivity of gastric contents after subjects have ingested a liquid or semisolid meal. This study validates the technique as a means of measuring gastric emptying. Experiments in vitro showed an excellent correlation between measurements of resistivity and either the square of the radius of a glass rod or the volume of water in a spherical balloon when both were placed in an oval tank containing saline. Altering the lateral position of the rod in the tank did not alter the values obtained. Images of abdominal resistivity were also directly correlated with the volume of air in a gastric balloon. Profiles of gastric emptying of liquid meals obtained using applied potential tomography were very similar to those obtained using scintigraphy or dye dilution techniques, provided that acid secretion was inhibited by cimetidine. Profiles of emptying of a mashed potato meal using applied potential tomography were also very similar to those obtained by scintigraphy. Measurements of the emptying of a liquid meal from the stomach were reproducible if acid secretion was inhibited by cimetidine. Thus, applied potential tomography is an accurate and reproducible method of measuring gastric emptying of liquids and particulate food. It is inexpensive, well tolerated, easy to use, and ideally suited for multiple studies in patients, even those who are pregnant.

  11. Optimization technique applied to interpretation of experimental data and research of constitutive laws

    International Nuclear Information System (INIS)

    Grossette, J.C.

    1982-01-01

    The feasibility of identification technique applied to one dimensional numerical analysis of the split-Hopkinson pressure bar experiment is proven. A general 1-D elastic-plastic-viscoplastic computer program was written down so as to give an adequate solution for elastic-plastic-viscoplastic response of a pressure bar subjected to a general Heaviside step loading function in time which is applied over one end of the bar. Special emphasis is placed on the response of the specimen during the first microseconds where no equilibrium conditions can be stated. During this transient phase discontinuity conditions related to wave propagation are encountered and must be carefully taken into account. Having derived an adequate numerical model, then Pontryagin identification technique has been applied in such a way that the unknowns are physical parameters. The solutions depend mainly on the selection of a class of proper eigen objective functionals (cost functions) which may be combined so as to obtain a convenient numerical objective function. A number of significant questions arising in the choice of parameter adjustment algorithms are discussed. In particular, this technique leads to a two point boundary value problem which has been solved using an iterative gradient like technique usually referred to as a double operator gradient method. This method combines the classical Fletcher-Powell technique and a partial quadratic technique with an automatic parameter step size selection. This method is much more efficient than usual ones. Numerical experimentation with simulated data was performed to test the accuracy and stability of the identification algorithm and to determine the most adequate type and quantity of data for estimation purposes

  12. Investigation of the shear bond strength to dentin of universal adhesives applied with two different techniques

    Directory of Open Access Journals (Sweden)

    Elif Yaşa

    2017-09-01

    Full Text Available Objective: The aim of this study was to evaluate the shear bond strength of universal adhesives applied with self-etch and etch&rinse techniques to dentin. Materials and Method: Fourty-eight sound extracted human third molars were used in this study. Occlusal enamel was removed in order to expose the dentinal surface, and the surface was flattened. Specimens were randomly divided into four groups and were sectioned vestibulo-lingually using a diamond disc. The universal adhesives: All Bond Universal (Group 1a and 1b, Gluma Bond Universal (Group 2a and 2b and Single Bond Universal (Group 3a and 3b were applied onto the tooth specimens either with self-etch technique (a or with etch&rinse technique (b according to the manufacturers’ instructions. Clearfil SE Bond (Group 4a; self-etch and Optibond FL (Group 4b; etch&rinse were used as control groups. Then the specimens were restored with a nanohybrid composite resin (Filtek Z550. After thermocycling, shear bond strength test was performed with a universal test machine at a crosshead speed of 0.5 mm/min. Fracture analysis was done under a stereomicroscope (×40 magnification. Data were analyzed using two-way ANOVA and post-hoc Tukey tests. Results: Statistical analysis showed significant differences in shear bond strength values between the universal adhesives (p<0.05. Significantly higher bond strength values were observed in self-etch groups (a in comparison to etch&rinse groups (b (p<0.05. Among all groups, Single Bond Universal showed the greatest shear bond strength values, whereas All Bond Universal showed the lowest shear bond strength values with both application techniques. Conclusion: Dentin bonding strengths of universal adhesives applied with different techniques may vary depending on the adhesive material. For the universal bonding agents tested in this study, the etch&rinse technique negatively affected the bond strength to dentin.

  13. Modelling the effects of the sterile insect technique applied to Eldana saccharina Walker in sugarcane

    Directory of Open Access Journals (Sweden)

    L Potgieter

    2012-12-01

    Full Text Available A mathematical model is formulated for the population dynamics of an Eldana saccharina Walker infestation of sugarcane under the influence of partially sterile released insects. The model describes the population growth of and interaction between normal and sterile E.saccharina moths in a temporally variable, but spatially homogeneous environment. The model consists of a deterministic system of difference equations subject to strictly positive initial data. The primary objective of this model is to determine suitable parameters in terms of which the above population growth and interaction may be quantified and according to which E.saccharina infestation levels and the associated sugarcane damage may be measured. Although many models have been formulated in the past describing the sterile insect technique, few of these models describe the technique for Lepidopteran species with more than one life stage and where F1-sterility is relevant. In addition, none of these models consider the technique when fully sterile females and partially sterile males are being released. The model formulated is also the first to describe the technique applied specifically to E.saccharina, and to consider the economic viability of applying the technique to this species. Pertinent decision support is provided to farm managers in terms of the best timing for releases, release ratios and release frequencies.

  14. Microscale and nanoscale strain mapping techniques applied to creep of rocks

    Science.gov (United States)

    Quintanilla-Terminel, Alejandra; Zimmerman, Mark E.; Evans, Brian; Kohlstedt, David L.

    2017-07-01

    Usually several deformation mechanisms interact to accommodate plastic deformation. Quantifying the contribution of each to the total strain is necessary to bridge the gaps from observations of microstructures, to geomechanical descriptions, to extrapolating from laboratory data to field observations. Here, we describe the experimental and computational techniques involved in microscale strain mapping (MSSM), which allows strain produced during high-pressure, high-temperature deformation experiments to be tracked with high resolution. MSSM relies on the analysis of the relative displacement of initially regularly spaced markers after deformation. We present two lithography techniques used to pattern rock substrates at different scales: photolithography and electron-beam lithography. Further, we discuss the challenges of applying the MSSM technique to samples used in high-temperature and high-pressure experiments. We applied the MSSM technique to a study of strain partitioning during creep of Carrara marble and grain boundary sliding in San Carlos olivine, synthetic forsterite, and Solnhofen limestone at a confining pressure, Pc, of 300 MPa and homologous temperatures, T/Tm, of 0.3 to 0.6. The MSSM technique works very well up to temperatures of 700 °C. The experimental developments described here show promising results for higher-temperature applications.

  15. Renormalization techniques applied to the study of density of states in disordered systems

    International Nuclear Information System (INIS)

    Ramirez Ibanez, J.

    1985-01-01

    A general scheme for real space renormalization of formal scattering theory is presented and applied to the calculation of density of states (DOS) in some finite width systems. This technique is extended in a self-consistent way, to the treatment of disordered and partially ordered chains. Numerical results of moments and DOS are presented in comparison with previous calculations. In addition, a self-consistent theory for the magnetic order problem in a Hubbard chain is derived and a parametric transition is observed. Properties of localization of the electronic states in disordered chains are studied through various decimation averaging techniques and using numerical simulations. (author) [pt

  16. Military labour mobilisation in colonial Lesotho during World War II ...

    African Journals Online (AJOL)

    In 1940, Great Britain's wartime exploitation of the human and material resources of its colonial empire was extended to colonial Lesotho (then known as Basutoland). The aim of this article, therefore, is to trace the four-year military labour mobilisation process in that colony, with special attention to the timing, number and ...

  17. Stabilisation of microalgae: Iodine mobilisation under aerobic and anaerobic conditions.

    Science.gov (United States)

    Han, Wei; Clarke, William; Pratt, Steven

    2015-10-01

    Mobilisation of iodine during microalgae stabilisation was investigated, with the view of assessing the potential of stabilised microalgae as an iodine-rich fertiliser. An iodine-rich waste microalgae (0.35 ± 0.05 mg I g(-1) VS(added)) was stabilised under aerobic and anaerobic conditions. Iodine mobilisation was linearly correlated with carbon emission, indicating iodine was in the form of organoiodine. Comparison between iodine and nitrogen mobilisation relative to carbon emission indicated that these elements were, at least in part, housed separately within the cells. After stabilisation, there were 0.22 ± 0.05 and 0.19 ± 0.01 mg g(-1) VS(added) iodine remaining in the solid in the aerobic and anaerobic processed material respectively, meaning 38 ± 5.0% (aerobic) and 50 ± 8.6% (anaerobic) of the iodine were mobilised, and consequently lost from the material. The iodine content of the stabilised material is comparable to the iodine content of some seaweed fertilisers, and potentially satisfies an efficient I-fertilisation dose. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Applying Data Mining Techniques to Improve Information Security in the Cloud: A Single Cache System Approach

    OpenAIRE

    Amany AlShawi

    2016-01-01

    Presently, the popularity of cloud computing is gradually increasing day by day. The purpose of this research was to enhance the security of the cloud using techniques such as data mining with specific reference to the single cache system. From the findings of the research, it was observed that the security in the cloud could be enhanced with the single cache system. For future purposes, an Apriori algorithm can be applied to the single cache system. This can be applied by all cloud providers...

  19. The efficacy of manual joint mobilisation/manipulation in treatment of lateral ankle sprains: a systematic review.

    Science.gov (United States)

    Loudon, Janice K; Reiman, Michael P; Sylvain, Jonathan

    2014-03-01

    Lateral ankle sprains are common and can have detrimental consequences to the athlete. Joint mobilisation/manipulation may limit these outcomes. Systematically summarise the effectiveness of manual joint techniques in treatment of lateral ankle sprains. This review employed the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines. A computer-assisted literature search of MEDLINE, CINHAL, EMBASE, OVID and Physiotherapy Evidence Database (PEDro) (January 1966 to March 2013) was used with the following keywords alone and in combination 'ankle', 'sprain', 'injuries', 'lateral', 'manual therapy', and 'joint mobilisation'. The methodological quality of individual studies was assessed using the PEDro scale. After screening of titles, abstracts and full articles, eight articles were kept for examination. Three articles achieved a score of 10 of 11 total points; one achieved a score of 9; two articles scored 8; one article scored a 7 and the remaining article scored a 5. Three articles examined joint techniques for acute sprains and the remainder examined subacute/chronic ankle sprains. Outcome measures included were pain level, ankle range of motion, swelling, functional score, stabilometry and gait parameters. The majority of the articles only assessed these outcome measures immediately after treatment. No detrimental effects from the joint techniques were revealed in any of the studies reviewed. For acute ankle sprains, manual joint mobilisation diminished pain and increased dorsiflexion range of motion. For treatment of subacute/chronic lateral ankle sprains, these techniques improved ankle range-of-motion, decreased pain and improved function.

  20. Development of technique to apply induction heating stress improvement to recirculation inlet nozzle

    International Nuclear Information System (INIS)

    Chiba, Kunihiko; Nihei, Kenichi; Ootaka, Minoru

    2009-01-01

    Stress corrosion cracking (SCC) have been found in the primary loop recirculation (PLR) systems of boiling water reactors (BWR). Residual stress in welding heat-affected zone is one of the factors of SCC, and the residual stress improvement is one of the most effective methods to prevent SCC. Induction heating stress improvement (IHSI) is one of the techniques to improve reduce residual stress. However, it is difficult to apply IHSI to the place such as the recirculation inlet nozzle where the flow stagnates. In this present study, the technique to apply IHSI to the recirculation inlet nozzle was developed using water jet which blowed into the crevice between the nozzle safe end and the thermal sleeve. (author)

  1. A Playful Multitude? Mobilising and Counter-Mobilising Immaterial Game Labour

    Directory of Open Access Journals (Sweden)

    Nick Dyer-Witheford

    2005-01-01

    Full Text Available Using the conceptual grid of "immaterial labour" in the age of Empire, this article is a preliminary portrait of work in the video and computer game development industry, a sector of creative, cognitive labour that exemplifies the allure but also the peril of new media work. Drawing on interviews we conducted with game developers in Canada , we examine the conditions of labour in game studios, this cultural industry's "work as play" ethos, the pleasures and potentialities of game production, the blemishes that mar this attractive vista, and the new infractions these tensions provoke. Confirming that Empire sets in motion potentialities it cannot fully control, we also observe an emergent counter-mobilisation of game labour, whose manifestations range from digital piracy to dissident games produced in the context of activism. These experiments of a playful multitude flow into the wider currents of tactical media, hacktivism, open-source software, and distributed computing that are generating tumults throughout the circuits of Empire.

  2. Evaluation of Economic Merger Control Techniques Applied to the European Electricity Sector

    International Nuclear Information System (INIS)

    Vandezande, Leen; Meeus, Leonardo; Delvaux, Bram; Van Calster, Geert; Belmans, Ronnie

    2006-01-01

    With European electricity markets not yet functioning on a competitive basis and consolidation increasing, the European Commission has said it intends to more intensively apply competition law in the electricity sector. Yet economic techniques and theories used in EC merger control fail to take sufficiently into account some specific features of electricity markets. The authors offer suggestions to enhance their reliability and applicability in the electricity sector. (author)

  3. Just-in-Time techniques as applied to hazardous materials management

    OpenAIRE

    Spicer, John S.

    1996-01-01

    Approved for public release; distribution is unlimited This study investigates the feasibility of integrating JIT techniques in the context of hazardous materials management. This study provides a description of JIT, a description of environmental compliance issues and the outgrowth of related HAZMAT policies, and a broad perspective on strategies for applying JIT to HAZMAT management. http://archive.org/details/justintimetechn00spic Lieutenant Commander, United States Navy

  4. The digital geometric phase technique applied to the deformation evaluation of MEMS devices

    International Nuclear Information System (INIS)

    Liu, Z W; Xie, H M; Gu, C Z; Meng, Y G

    2009-01-01

    Quantitative evaluation of the structure deformation of microfabricated electromechanical systems is of importance for the design and functional control of microsystems. In this investigation, a novel digital geometric phase technique was developed to meet the deformation evaluation requirement of microelectromechanical systems (MEMS). The technique is performed on the basis of regular artificial lattices, instead of a natural atom lattice. The regular artificial lattices with a pitch ranging from micrometer to nanometer will be directly fabricated on the measured surface of MEMS devices by using a focused ion beam (FIB). Phase information can be obtained from the Bragg filtered images after fast Fourier transform (FFT) and inverse fast Fourier transform (IFFT) of the scanning electronic microscope (SEM) images. Then the in-plane displacement field and the local strain field related to the phase information will be evaluated. The obtained results show that the technique can be well applied to deformation measurement with nanometer sensitivity and stiction force estimation of a MEMS device

  5. Evaluation of irradiation damage effect by applying electric properties based techniques

    International Nuclear Information System (INIS)

    Acosta, B.; Sevini, F.

    2004-01-01

    The most important effect of the degradation by radiation is the decrease in the ductility of the pressure vessel of the reactor (RPV) ferritic steels. The main way to determine the mechanical behaviour of the RPV steels is tensile and impact tests, from which the ductile to brittle transition temperature (DBTT) and its increase due to neutron irradiation can be calculated. These tests are destructive and regularly applied to surveillance specimens to assess the integrity of RPV. The possibility of applying validated non-destructive ageing monitoring techniques would however facilitate the surveillance of the materials that form the reactor vessel. The JRC-IE has developed two devices, focused on the measurement of the electrical properties to assess non-destructively the embrittlement state of materials. The first technique, called Seebeck and Thomson Effects on Aged Material (STEAM), is based on the measurement of the Seebeck coefficient, characteristic of the material and related to the microstructural changes induced by irradiation embrittlement. With the same aim the second technique, named Resistivity Effects on Aged Material (REAM), measures instead the resistivity of the material. The purpose of this research is to correlate the results of the impact tests, STEAM and REAM measurements with the change in the mechanical properties due to neutron irradiation. These results will make possible the improvement of such techniques based on the measurement of material electrical properties for their application to the irradiation embrittlement assessment

  6. Simulation as a tool for developing knowledge mobilisation strategies: Innovative knowledge transfer in youth services

    Directory of Open Access Journals (Sweden)

    Michael Ungar

    2015-09-01

    Full Text Available While there are excellent models of knowledge mobilisation (KMb that address the opportunity for co-production and sharing of best practice knowledge among human service professionals, it remains unclear whether these models will work in less formal settings like community-based non-government organisations (NGOs where there are fewer resources for KMb. For three days, 65 policy-makers, senior staff of NGOs, mental health professionals, KMb specialists and youth participated in a set of simulation exercises to problem solve how to mobilise knowledge in less formal settings that provide services to children and youth in challenging contexts (CYCC. Based on simulation exercises used in other settings (such as the deployment of international aid workers, participants were first provided with reports synthesising best practice knowledge relevant to their workplaces. They then engaged in an appreciative inquiry process, and were finally tasked with developing innovative strategies for KMb. Observation notes and exit interviews were used to evaluate the process and assess impact. Findings related to the process of the simulation exercises show the technique of simulation to be useful but that it requires effort to keep participants focused on the task of KMb rather than the content of best practices within a focal population. With regard to developing innovative KMb strategies, findings suggest that service providers in less formal community-based services prefer KMb activities that promote one-to-one relationships, including the participation of youth themselves, who can speak to the effectiveness of the interventions they have experienced. Unexpectedly, the use of electronic communication, including social media, was not viewed very positively by participants. These results suggest that the use of simulation to search for innovative KMb strategies and to problem solve around barriers to KMb has the potential to inform new ways of co-producing and

  7. Super Resolution and Interference Suppression Technique applied to SHARAD Radar Data

    Science.gov (United States)

    Raguso, M. C.; Mastrogiuseppe, M.; Seu, R.; Piazzo, L.

    2017-12-01

    We will present a super resolution and interference suppression technique applied to the data acquired by the SHAllow RADar (SHARAD) on board the NASA's 2005 Mars Reconnaissance Orbiter (MRO) mission, currently operating around Mars [1]. The algorithms allow to improve the range resolution roughly by a factor of 3 and the Signal to Noise Ratio (SNR) by a several decibels. Range compression algorithms usually adopt conventional Fourier transform techniques, which are limited in the resolution by the transmitted signal bandwidth, analogous to the Rayleigh's criterion in optics. In this work, we investigate a super resolution method based on autoregressive models and linear prediction techniques [2]. Starting from the estimation of the linear prediction coefficients from the spectral data, the algorithm performs the radar bandwidth extrapolation (BWE), thereby improving the range resolution of the pulse-compressed coherent radar data. Moreover, the EMIs (ElectroMagnetic Interferences) are detected and the spectra is interpolated in order to reconstruct an interference free spectrum, thereby improving the SNR. The algorithm can be applied to the single complex look image after synthetic aperture processing (SAR). We apply the proposed algorithm to simulated as well as to real radar data. We will demonstrate the effective enhancement on vertical resolution with respect to the classical spectral estimator. We will show that the imaging of the subsurface layered structures observed in radargrams is improved, allowing additional insights for the scientific community in the interpretation of the SHARAD radar data, which will help to further our understanding of the formation and evolution of known geological features on Mars. References: [1] Seu et al. 2007, Science, 2007, 317, 1715-1718 [2] K.M. Cuomo, "A Bandwidth Extrapolation Technique for Improved Range Resolution of Coherent Radar Data", Project Report CJP-60, Revision 1, MIT Lincoln Laboratory (4 Dec. 1992).

  8. Wire-mesh and ultrasound techniques applied for the characterization of gas-liquid slug flow

    Energy Technology Data Exchange (ETDEWEB)

    Ofuchi, Cesar Y.; Sieczkowski, Wytila Chagas; Neves Junior, Flavio; Arruda, Lucia V.R.; Morales, Rigoberto E.M.; Amaral, Carlos E.F.; Silva, Marco J. da [Federal University of Technology of Parana, Curitiba, PR (Brazil)], e-mails: ofuchi@utfpr.edu.br, wytila@utfpr.edu.br, neves@utfpr.edu.br, lvrarruda@utfpr.edu.br, rmorales@utfpr.edu.br, camaral@utfpr.edu.br, mdasilva@utfpr.edu.br

    2010-07-01

    Gas-liquid two-phase flows are found in a broad range of industrial applications, such as chemical, petrochemical and nuclear industries and quite often determine the efficiency and safety of process and plants. Several experimental techniques have been proposed and applied to measure and quantify two-phase flows so far. In this experimental study the wire-mesh sensor and an ultrasound technique are used and comparatively evaluated to study two-phase slug flows in horizontal pipes. The wire-mesh is an imaging technique and thus appropriated for scientific studies while ultrasound-based technique is robust and non-intrusive and hence well suited for industrial applications. Based on the measured raw data it is possible to extract some specific slug flow parameters of interest such as mean void fraction and characteristic frequency. The experiments were performed in the Thermal Sciences Laboratory (LACIT) at UTFPR, Brazil, in which an experimental two-phase flow loop is available. The experimental flow loop comprises a horizontal acrylic pipe of 26 mm diameter and 9 m length. Water and air were used to produce the two phase flow under controlled conditions. The results show good agreement between the techniques. (author)

  9. The correlated k-distribution technique as applied to the AVHRR channels

    Science.gov (United States)

    Kratz, David P.

    1995-01-01

    Correlated k-distributions have been created to account for the molecular absorption found in the spectral ranges of the five Advanced Very High Resolution Radiometer (AVHRR) satellite channels. The production of the k-distributions was based upon an exponential-sum fitting of transmissions (ESFT) technique which was applied to reference line-by-line absorptance calculations. To account for the overlap of spectral features from different molecular species, the present routines made use of the multiplication transmissivity property which allows for considerable flexibility, especially when altering relative mixing ratios of the various molecular species. To determine the accuracy of the correlated k-distribution technique as compared to the line-by-line procedure, atmospheric flux and heating rate calculations were run for a wide variety of atmospheric conditions. For the atmospheric conditions taken into consideration, the correlated k-distribution technique has yielded results within about 0.5% for both the cases where the satellite spectral response functions were applied and where they were not. The correlated k-distribution's principal advantages is that it can be incorporated directly into multiple scattering routines that consider scattering as well as absorption by clouds and aerosol particles.

  10. Using wavelet denoising and mathematical morphology in the segmentation technique applied to blood cells images.

    Science.gov (United States)

    Boix, Macarena; Cantó, Begoña

    2013-04-01

    Accurate image segmentation is used in medical diagnosis since this technique is a noninvasive pre-processing step for biomedical treatment. In this work we present an efficient segmentation method for medical image analysis. In particular, with this method blood cells can be segmented. For that, we combine the wavelet transform with morphological operations. Moreover, the wavelet thresholding technique is used to eliminate the noise and prepare the image for suitable segmentation. In wavelet denoising we determine the best wavelet that shows a segmentation with the largest area in the cell. We study different wavelet families and we conclude that the wavelet db1 is the best and it can serve for posterior works on blood pathologies. The proposed method generates goods results when it is applied on several images. Finally, the proposed algorithm made in MatLab environment is verified for a selected blood cells.

  11. Mathematical Model and Artificial Intelligent Techniques Applied to a Milk Industry through DSM

    Science.gov (United States)

    Babu, P. Ravi; Divya, V. P. Sree

    2011-08-01

    The resources for electrical energy are depleting and hence the gap between the supply and the demand is continuously increasing. Under such circumstances, the option left is optimal utilization of available energy resources. The main objective of this chapter is to discuss about the Peak load management and overcome the problems associated with it in processing industries such as Milk industry with the help of DSM techniques. The chapter presents a generalized mathematical model for minimizing the total operating cost of the industry subject to the constraints. The work presented in this chapter also deals with the results of application of Neural Network, Fuzzy Logic and Demand Side Management (DSM) techniques applied to a medium scale milk industrial consumer in India to achieve the improvement in load factor, reduction in Maximum Demand (MD) and also the consumer gets saving in the energy bill.

  12. Applied methods and techniques for mechatronic systems modelling, identification and control

    CERN Document Server

    Zhu, Quanmin; Cheng, Lei; Wang, Yongji; Zhao, Dongya

    2014-01-01

    Applied Methods and Techniques for Mechatronic Systems brings together the relevant studies in mechatronic systems with the latest research from interdisciplinary theoretical studies, computational algorithm development and exemplary applications. Readers can easily tailor the techniques in this book to accommodate their ad hoc applications. The clear structure of each paper, background - motivation - quantitative development (equations) - case studies/illustration/tutorial (curve, table, etc.) is also helpful. It is mainly aimed at graduate students, professors and academic researchers in related fields, but it will also be helpful to engineers and scientists from industry. Lei Liu is a lecturer at Huazhong University of Science and Technology (HUST), China; Quanmin Zhu is a professor at University of the West of England, UK; Lei Cheng is an associate professor at Wuhan University of Science and Technology, China; Yongji Wang is a professor at HUST; Dongya Zhao is an associate professor at China University o...

  13. Advanced gamma spectrum processing technique applied to the analysis of scattering spectra for determining material thickness

    International Nuclear Information System (INIS)

    Hoang Duc Tam; VNUHCM-University of Science, Ho Chi Minh City; Huynh Dinh Chuong; Tran Thien Thanh; Vo Hoang Nguyen; Hoang Thi Kieu Trang; Chau Van Tao

    2015-01-01

    In this work, an advanced gamma spectrum processing technique is applied to analyze experimental scattering spectra for determining the thickness of C45 heat-resistant steel plates. The single scattering peak of scattering spectra is taken as an advantage to measure the intensity of single scattering photons. Based on these results, the thickness of steel plates is determined with a maximum deviation of real thickness and measured thickness of about 4 %. Monte Carlo simulation using MCNP5 code is also performed to cross check the results, which yields a maximum deviation of 2 %. These results strongly confirm the capability of this technique in analyzing gamma scattering spectra, which is a simple, effective and convenient method for determining material thickness. (author)

  14. Software engineering techniques applied to agricultural systems an object-oriented and UML approach

    CERN Document Server

    Papajorgji, Petraq J

    2014-01-01

    Software Engineering Techniques Applied to Agricultural Systems presents cutting-edge software engineering techniques for designing and implementing better agricultural software systems based on the object-oriented paradigm and the Unified Modeling Language (UML). The focus is on the presentation of  rigorous step-by-step approaches for modeling flexible agricultural and environmental systems, starting with a conceptual diagram representing elements of the system and their relationships. Furthermore, diagrams such as sequential and collaboration diagrams are used to explain the dynamic and static aspects of the software system.    This second edition includes: a new chapter on Object Constraint Language (OCL), a new section dedicated to the Model-VIEW-Controller (MVC) design pattern, new chapters presenting details of two MDA-based tools – the Virtual Enterprise and Olivia Nova, and a new chapter with exercises on conceptual modeling.  It may be highly useful to undergraduate and graduate students as t...

  15. Applying traditional signal processing techniques to social media exploitation for situational understanding

    Science.gov (United States)

    Abdelzaher, Tarek; Roy, Heather; Wang, Shiguang; Giridhar, Prasanna; Al Amin, Md. Tanvir; Bowman, Elizabeth K.; Kolodny, Michael A.

    2016-05-01

    Signal processing techniques such as filtering, detection, estimation and frequency domain analysis have long been applied to extract information from noisy sensor data. This paper describes the exploitation of these signal processing techniques to extract information from social networks, such as Twitter and Instagram. Specifically, we view social networks as noisy sensors that report events in the physical world. We then present a data processing stack for detection, localization, tracking, and veracity analysis of reported events using social network data. We show using a controlled experiment that the behavior of social sources as information relays varies dramatically depending on context. In benign contexts, there is general agreement on events, whereas in conflict scenarios, a significant amount of collective filtering is introduced by conflicted groups, creating a large data distortion. We describe signal processing techniques that mitigate such distortion, resulting in meaningful approximations of actual ground truth, given noisy reported observations. Finally, we briefly present an implementation of the aforementioned social network data processing stack in a sensor network analysis toolkit, called Apollo. Experiences with Apollo show that our techniques are successful at identifying and tracking credible events in the physical world.

  16. Applying Data Mining Techniques to Improve Information Security in the Cloud: A Single Cache System Approach

    Directory of Open Access Journals (Sweden)

    Amany AlShawi

    2016-01-01

    Full Text Available Presently, the popularity of cloud computing is gradually increasing day by day. The purpose of this research was to enhance the security of the cloud using techniques such as data mining with specific reference to the single cache system. From the findings of the research, it was observed that the security in the cloud could be enhanced with the single cache system. For future purposes, an Apriori algorithm can be applied to the single cache system. This can be applied by all cloud providers, vendors, data distributors, and others. Further, data objects entered into the single cache system can be extended into 12 components. Database and SPSS modelers can be used to implement the same.

  17. Markov chain Monte Carlo techniques applied to parton distribution functions determination: Proof of concept

    Science.gov (United States)

    Gbedo, Yémalin Gabin; Mangin-Brinet, Mariane

    2017-07-01

    We present a new procedure to determine parton distribution functions (PDFs), based on Markov chain Monte Carlo (MCMC) methods. The aim of this paper is to show that we can replace the standard χ2 minimization by procedures grounded on statistical methods, and on Bayesian inference in particular, thus offering additional insight into the rich field of PDFs determination. After a basic introduction to these techniques, we introduce the algorithm we have chosen to implement—namely Hybrid (or Hamiltonian) Monte Carlo. This algorithm, initially developed for Lattice QCD, turns out to be very interesting when applied to PDFs determination by global analyses; we show that it allows us to circumvent the difficulties due to the high dimensionality of the problem, in particular concerning the acceptance. A first feasibility study is performed and presented, which indicates that Markov chain Monte Carlo can successfully be applied to the extraction of PDFs and of their uncertainties.

  18. Removal of benzaldehyde from a water/ethanol mixture by applying scavenging techniques

    DEFF Research Database (Denmark)

    Mitic, Aleksandar; Skov, Thomas; Gernaey, Krist V.

    2017-01-01

    A presence of carbonyl compounds is very common in the food industry. The nature of such compounds is to be reactive and thus many products involve aldehydes/ketones in their synthetic routes. By contrast, the high reactivity of carbonyl compounds could also lead to formation of undesired compounds......, such as genotoxic impurities. It can therefore be important to remove carbonyl compounds by implementing suitable removal techniques, with the aim of protecting final product quality. This work is focused on benzaldehyde as a model component, studying its removal from a water/ethanol mixture by applying different...

  19. Comparative effectiveness of manipulation, mobilisation and the Activator instrument in treatment of non-specific neck pain: a systematic review

    Directory of Open Access Journals (Sweden)

    Miller Peter

    2006-04-01

    Full Text Available Abstract Background Neck pain is a common problem and different forms of manual therapy are used in its treatment. The purpose of this systematic review was to critically appraise the literature that directly compared manipulation, mobilisation and the Activator instrument for non-specific neck pain. Methods Electronic databases (MEDLINE, MANTIS and CINAHL were searched from their inception to October 2005 for all English language randomised clinical trials that directly compared manipulation, mobilisation and the Activator instrument. Inclusion and exclusion criteria were applied to select the studies and these studies were then evaluated using validated criteria. Results Five such studies were identified. The methodological quality was mostly poor. Findings from the studies were mixed and no one therapy was shown to be more effective than the others. Conclusion Further high quality research has to be done before a recommendation can be made as to the most effective manual method for non-specific neck pain.

  20. Mobile media, mobility and mobilisation in the current museum field

    DEFF Research Database (Denmark)

    Baggesen, Rikke Haller

    2017-01-01

    Introducing the concept of a 'mobile museology' to describe how museums are currently set in motion by a confluence of cultural, technological and museological developments, this chapter traces the connections between mobile media and notions of mobility and mobilisation in the museum field....... As illustrated by current examples in the chapter, mobile phones have thus provided an opportunity for both augmenting and transcending the museum space, blurring former boundaries between institutions and their environments. At the same time, technological advances and digitial culture developments have also...... required and inspired museums to become organisationally mobile, and to mobilise collections, audiences and institutions in order to fulfill museum missions. In this perspective, mobile media are thus seen as both catalysts and instruments for current museum developments....

  1. Carbon dioxide triggered metal(loid) mobilisation in a mofette

    DEFF Research Database (Denmark)

    Beulig, Felix

    2014-01-01

    Carbon capture and geologic storage is a frequently discussed option to reduce atmospheric CO2 concentrations with the long-term risk of leakage from storage sites to overlying aquifers and soils. We chose natural CO2 exhalations, so-called mofettes, in a wetland area in the Czech Republic...... as analogues to follow the fate of metal(loid)s under CO2-saturated conditions. Compared to the reference fluvisol at the study site, mofette soils exhibited lower pH (4.9 ± 0.05) and redox potential (300 ± 40 mV), as well as higher organic carbon contents. Poorly crystalline and crystalline Fe (hydr...... to complexation and/or adsorption to organic carbon and the small amount of Fe (hydr)oxides. A one-month-in-situ mobilisation experiment showed mobilisation of all investigated elements to the aqueous phase suggesting that desorption is the faster and initially dominating process while resorption is a secondary...

  2. Anti-Islamic PEGIDA beyond Germany : explaining differences in mobilisation

    OpenAIRE

    BERNTZEN, Lars Erik; WEISSKIRCHER, Manès

    2016-01-01

    First published online: 28 October 2016 The rise of anti-Islamic PEGIDA (Patriotische Europäer gegen die Islamisierung des Abendlandes) is one of the latest sustained episodes of radical right mobilisation in Western Europe outside the electoral arena. This study provides a first comparative analysis of PEGIDA beyond Germany and its core region of Saxony. Combining protest event analysis with online data and network analysis, we identify why PEGIDA mustered low-scale support in some countr...

  3. Arsenic and selenium mobilisation from organic matter treated mine spoil with and without inorganic fertilisation

    International Nuclear Information System (INIS)

    Moreno-Jiménez, Eduardo; Clemente, Rafael; Mestrot, Adrien; Meharg, Andrew A.

    2013-01-01

    Organic matter amendments are applied to contaminated soil to provide a better habitat for re-vegetation and remediation, and olive mill waste compost (OMWC) has been described as a promising material for this aim. We report here the results of an incubation experiment carried out in flooded conditions to study its influence in As and metal solubility in a trace elements contaminated soil. NPK fertilisation and especially organic amendment application resulted in increased As, Se and Cu concentrations in pore water. Independent of the amendment, dimethylarsenic acid (DMA) was the most abundant As species in solution. The application of OMWC increased pore water dissolved organic-carbon (DOC) concentrations, which may explain the observed mobilisation of As, Cu and Se; phosphate added in NPK could also be in part responsible of the mobilisation caused in As. Therefore, the application of soil amendments in mine soils may be particularly problematic in flooded systems. Highlights: ► Organic and inorganic amendments were added to a mine soil in flooding conditions. ► Olive mill waste compost (OMWC) provoked As, Se and Cu solubilisation. ► Dimethylarsenic acid (DMA) was the predominant As species in pore water. ► Selenium volatilisation from soils was intense. - The addition of organic amendment and/or inorganic fertiliser to a trace element contaminated soil in flooded conditions led to As, Cu and Se solubilisation.

  4. Applied research on air pollution using nuclear-related analytical techniques

    International Nuclear Information System (INIS)

    1994-01-01

    A co-ordinated research programme (CRP) on applied research on air pollution using nuclear-related techniques is a global CRP which will run from 1992-1996, and will build upon the experience gained by the Agency from the laboratory support that it has been providing for several years to BAPMoN - the Background Air Pollution Monitoring Network programme organized under the auspices of the World Meterological Organization. The purpose of this CRP is to promote the use of nuclear analytical techniques in air pollution studies, e.g. NAA, XFR, and PIXE for the analysis of toxic and other trace elements in suspended particulate matter (including air filter samples), rainwater and fog-water samples, and in biological indicators of air pollution (e.g. lichens and mosses). The main purposes of the core programme are i) to support the use of nuclear and nuclear-related analytical techniques for practically-oriented research and monitoring studies on air pollution ii) to identify major sources of air pollution affecting each of the participating countries with particular reference to toxic heavy metals, and iii) to obtain comparative data on pollution levels in areas of high pollution (e.g. a city centre or a populated area downwind of a large pollution source) and low pollution (e.g. rural areas). This document reports the discussions held during the first Research Co-ordination Meeting (RCM) for the CRP which took place at the IAEA Headquarters in Vienna. Refs, figs and tabs

  5. Case study: how to apply data mining techniques in a healthcare data warehouse.

    Science.gov (United States)

    Silver, M; Sakata, T; Su, H C; Herman, C; Dolins, S B; O'Shea, M J

    2001-01-01

    Healthcare provider organizations are faced with a rising number of financial pressures. Both administrators and physicians need help analyzing large numbers of clinical and financial data when making decisions. To assist them, Rush-Presbyterian-St. Luke's Medical Center and Hitachi America, Ltd. (HAL), Inc., have partnered to build an enterprise data warehouse and perform a series of case study analyses. This article focuses on one analysis, which was performed by a team of physicians and computer science researchers, using a commercially available on-line analytical processing (OLAP) tool in conjunction with proprietary data mining techniques developed by HAL researchers. The initial objective of the analysis was to discover how to use data mining techniques to make business decisions that can influence cost, revenue, and operational efficiency while maintaining a high level of care. Another objective was to understand how to apply these techniques appropriately and to find a repeatable method for analyzing data and finding business insights. The process used to identify opportunities and effect changes is described.

  6. The mobilisation model and parameter sensitivity

    International Nuclear Information System (INIS)

    Blok, B.M.

    1993-12-01

    In the PRObabillistic Safety Assessment (PROSA) of radioactive waste in a salt repository one of the nuclide release scenario's is the subrosion scenario. A new subrosion model SUBRECN has been developed. In this model the combined effect of a depth-dependent subrosion, glass dissolution, and salt rise has been taken into account. The subrosion model SUBRECN and the implementation of this model in the German computer program EMOS4 is presented. A new computer program PANTER is derived from EMOS4. PANTER models releases of radionuclides via subrosion from a disposal site in a salt pillar into the biosphere. For uncertainty and sensitivity analyses the new subrosion model Latin Hypercube Sampling has been used for determine the different values for the uncertain parameters. The influence of the uncertainty in the parameters on the dose calculations has been investigated by the following sensitivity techniques: Spearman Rank Correlation Coefficients, Partial Rank Correlation Coefficients, Standardised Rank Regression Coefficients, and the Smirnov Test. (orig./HP)

  7. Recent developments and evaluation of selected geochemical techniques applied to uranium exploration

    International Nuclear Information System (INIS)

    Wenrich-Verbeek, K.J.; Cadigan, R.A.; Felmlee, J.K.; Reimer, G.M.; Spirakis, C.S.

    1976-01-01

    Various geochemical techniques for uranium exploration are currently under study by the geochemical techniques team of the Branch of Uranium and Thorium Resources, US Geological Survey. Radium-226 and its parent uranium-238 occur in mineral spring water largely independently of the geochemistry of the solutions and thus are potential indicators of uranium in source rocks. Many radioactive springs, hot or cold, are believed to be related to hydrothermal systems which contain uranium at depth. Radium, when present in the water, is co-precipitated in iron and/or manganese oxides and hydroxides or in barium sulphate associated with calcium carbonate spring deposits. Studies of surface water samples have resulted in improved standardized sample treatment and collection procedures. Stream discharge has been shown to have a significant effect on uranium concentration, while conductivity shows promise as a ''pathfinder'' for uranium. Turbid samples behave differently and consequently must be treated with more caution than samples from clear streams. Both water and stream sediments should be sampled concurrently, as anomalous uranium concentrations may occur in only one of these media and would be overlooked if only one, the wrong one, were analysed. The fission-track technique has been applied to uranium determinations in the above water studies. The advantages of the designed sample collecting system are that only a small quantity, typically one drop, of water is required and sample manipulation is minimized, thereby reducing contamination risks. The fission-track analytical technique is effective at the uranium concentration levels commonly found in natural waters (5.0-0.01 μg/litre). Landsat data were used to detect alteration associated with uranium deposits. Altered areas were detected but were not uniquely defined. Nevertheless, computer processing of Landsat data did suggest a smaller size target for further evaluation and thus is useful as an exploration tool

  8. Determination of hydrogen diffusivity and permeability in W near room temperature applying a tritium tracer technique

    International Nuclear Information System (INIS)

    Ikeda, T.; Otsuka, T.; Tanabe, T.

    2011-01-01

    Tungsten is a primary candidate of plasma facing material in ITER and beyond, owing to its good thermal property and low erosion. But hydrogen solubility and diffusivity near ITER operation temperatures (below 500 K) have scarcely studied. Mainly because its low hydrogen solubility and diffusivity at lower temperatures make the detection of hydrogen quite difficult. We have tried to observe hydrogen plasma driven permeation (PDP) through nickel and tungsten near room temperatures applying a tritium tracer technique, which is extremely sensible to detect tritium diluted in hydrogen. The apparent diffusion coefficients for PDP were determined by permeation lag times at first time, and those for nickel and tungsten were similar or a few times larger than those for gas driven permeation (GDP). The permeation rates for PDP in nickel and tungsten were larger than those for GDP normalized to the same gas pressure about 20 and 5 times larger, respectively.

  9. Laser--Doppler anemometry technique applied to two-phase dispersed flows in a rectangular channel

    International Nuclear Information System (INIS)

    Lee, S.L.; Srinivasan, J.

    1979-01-01

    A new optical technique using Laser--Doppler anemometry has been applied to the local measurement of turbulent upward flow of a dilute water droplet--air two-phase dispersion in a vertical rectangular channel. Individually examined were over 20,000 droplet signals coming from each of a total of ten transversely placed measuring points, the closest of which to the channel wall was 250 μ away from the wall. Two flows of different patterns due to different imposed flow conditions were investigated, one with and the other without a liquid film formed on the channel wall. Reported are the size and number density distribution and the axial and lateral velocity distributions for the droplets as well as the axial and lateral velocity distributions for the air

  10. Technique of uranium exploration in tropical rain forests as applied in Sumatra and other tropical areas

    International Nuclear Information System (INIS)

    Hahn, L.

    1983-01-01

    The technique of uranium prospecting in areas covered by tropical rain forest is discussed using a uranium exploration campaign conducted from 1976 to 1978 in Western Sumatra as an example. A regional reconnaissance survey using stream sediment samples combined with radiometric field measurements proved ideal for covering very large areas. A mobile field laboratory was used for the geochemical survey. Helicopter support in diffult terrain was found to be very efficient and economical. A field procedure for detecting low uranium concentrations in stream water samples is described. This method has been successfully applied in Sarawak. To distinguish meaningful uranium anomalies in water from those with no meaning for prospecting, the correlations between U content and conductivity of the water and between U content and Ca and HCO 3 content must be considered. This method has been used successfully in a geochemical survey in Thailand. (author)

  11. A systematic review of applying modern software engineering techniques to developing robotic systems

    Directory of Open Access Journals (Sweden)

    Claudia Pons

    2012-01-01

    Full Text Available Robots have become collaborators in our daily life. While robotic systems become more and more complex, the need to engineer their software development grows as well. The traditional approaches used in developing these software systems are reaching their limits; currently used methodologies and tools fall short of addressing the needs of such complex software development. Separating robotics’ knowledge from short-cycled implementation technologies is essential to foster reuse and maintenance. This paper presents a systematic review (SLR of the current use of modern software engineering techniques for developing robotic software systems and their actual automation level. The survey was aimed at summarizing existing evidence concerning applying such technologies to the field of robotic systems to identify any gaps in current research to suggest areas for further investigation and provide a background for positioning new research activities.

  12. Vibration monitoring/diagnostic techniques, as applied to reactor coolant pumps

    International Nuclear Information System (INIS)

    Sculthorpe, B.R.; Johnson, K.M.

    1986-01-01

    With the increased awareness of reactor coolant pump (RCP) cracked shafts, brought about by the catastrophic shaft failure at Crystal River number3, Florida Power and Light Company, in conjunction with Bently Nevada Corporation, undertook a test program at St. Lucie Nuclear Unit number2, to confirm the integrity of all four RCP pump shafts. Reactor coolant pumps play a major roll in the operation of nuclear-powered generation facilities. The time required to disassemble and physically inspect a single RCP shaft would be lengthy, monetarily costly to the utility and its customers, and cause possible unnecessary man-rem exposure to plant personnel. When properly applied, vibration instrumentation can increase unit availability/reliability, as well as provide enhanced diagnostic capability. This paper reviews monitoring benefits and diagnostic techniques applicable to RCPs/motor drives

  13. Effect of early and late mobilisation on split skin graft outcome.

    Science.gov (United States)

    Luczak, Bernard; Ha, Jennifer; Gurfinkel, Reuven

    2012-02-01

    There is an increasing trend towards early mobilisation post-split skin grafting of the lower limbs. This study was performed to determine if early mobilisation impacts negatively on graft healing and patient morbidity. A retrospective review of 48 cases of lower limb split skin grafts performed by the plastic surgery department at Royal Perth Hospital was undertaken. Patients were stratified into early and late mobilisation groups. No difference in outcome was identified with early mobilisation, but an increased rate of deconditioning with increased length of stay was present with late mobilisation. These results suggest that early mobilisation post-split skin grafting of the lower limb is beneficial to patient care and is associated with lower morbidity. © 2011 The Authors. Australasian Journal of Dermatology © 2011 The Australasian College of Dermatologists.

  14. Creep lifing methodologies applied to a single crystal superalloy by use of small scale test techniques

    Energy Technology Data Exchange (ETDEWEB)

    Jeffs, S.P., E-mail: s.p.jeffs@swansea.ac.uk [Institute of Structural Materials, Swansea University, Singleton Park SA2 8PP (United Kingdom); Lancaster, R.J. [Institute of Structural Materials, Swansea University, Singleton Park SA2 8PP (United Kingdom); Garcia, T.E. [IUTA (University Institute of Industrial Technology of Asturias), University of Oviedo, Edificio Departamental Oeste 7.1.17, Campus Universitario, 33203 Gijón (Spain)

    2015-06-11

    In recent years, advances in creep data interpretation have been achieved either by modified Monkman–Grant relationships or through the more contemporary Wilshire equations, which offer the opportunity of predicting long term behaviour extrapolated from short term results. Long term lifing techniques prove extremely useful in creep dominated applications, such as in the power generation industry and in particular nuclear where large static loads are applied, equally a reduction in lead time for new alloy implementation within the industry is critical. The latter requirement brings about the utilisation of the small punch (SP) creep test, a widely recognised approach for obtaining useful mechanical property information from limited material volumes, as is typically the case with novel alloy development and for any in-situ mechanical testing that may be required. The ability to correlate SP creep results with uniaxial data is vital when considering the benefits of the technique. As such an equation has been developed, known as the k{sub SP} method, which has been proven to be an effective tool across several material systems. The current work now explores the application of the aforementioned empirical approaches to correlate small punch creep data obtained on a single crystal superalloy over a range of elevated temperatures. Finite element modelling through ABAQUS software based on the uniaxial creep data has also been implemented to characterise the SP deformation and help corroborate the experimental results.

  15. Creep lifing methodologies applied to a single crystal superalloy by use of small scale test techniques

    International Nuclear Information System (INIS)

    Jeffs, S.P.; Lancaster, R.J.; Garcia, T.E.

    2015-01-01

    In recent years, advances in creep data interpretation have been achieved either by modified Monkman–Grant relationships or through the more contemporary Wilshire equations, which offer the opportunity of predicting long term behaviour extrapolated from short term results. Long term lifing techniques prove extremely useful in creep dominated applications, such as in the power generation industry and in particular nuclear where large static loads are applied, equally a reduction in lead time for new alloy implementation within the industry is critical. The latter requirement brings about the utilisation of the small punch (SP) creep test, a widely recognised approach for obtaining useful mechanical property information from limited material volumes, as is typically the case with novel alloy development and for any in-situ mechanical testing that may be required. The ability to correlate SP creep results with uniaxial data is vital when considering the benefits of the technique. As such an equation has been developed, known as the k SP method, which has been proven to be an effective tool across several material systems. The current work now explores the application of the aforementioned empirical approaches to correlate small punch creep data obtained on a single crystal superalloy over a range of elevated temperatures. Finite element modelling through ABAQUS software based on the uniaxial creep data has also been implemented to characterise the SP deformation and help corroborate the experimental results

  16. VIDEOGRAMMETRIC RECONSTRUCTION APPLIED TO VOLCANOLOGY: PERSPECTIVES FOR A NEW MEASUREMENT TECHNIQUE IN VOLCANO MONITORING

    Directory of Open Access Journals (Sweden)

    Emmanuelle Cecchi

    2011-05-01

    Full Text Available This article deals with videogrammetric reconstruction of volcanic structures. As a first step, the method is tested in laboratory. The objective is to reconstruct small sand and plaster cones, analogous to volcanoes, that deform with time. The initial stage consists in modelling the sensor (internal parameters and calculating its orientation and position in space, using a multi-view calibration method. In practice two sets of views are taken: a first one around a calibration target and a second one around the studied object. Both sets are combined in the calibration software to simultaneously compute the internal parameters modelling the sensor, and the external parameters giving the spatial location of each view around the cone. Following this first stage, a N-view reconstruction process is carried out. The principle is as follows: an initial 3D model of the cone is created and then iteratively deformed to fit the real object. The deformation of the meshed model is based on a texture coherence criterion. At present, this reconstruction method and its precision are being validated at laboratory scale. The objective will be then to follow analogue model deformation with time using successive reconstructions. In the future, the method will be applied to real volcanic structures. Modifications of the initial code will certainly be required, however excellent reconstruction accuracy, valuable simplicity and flexibility of the technique are expected, compared to classic stereophotogrammetric techniques used in volcanology.

  17. How Can Synchrotron Radiation Techniques Be Applied for Detecting Microstructures in Amorphous Alloys?

    Directory of Open Access Journals (Sweden)

    Gu-Qing Guo

    2015-11-01

    Full Text Available In this work, how synchrotron radiation techniques can be applied for detecting the microstructure in metallic glass (MG is studied. The unit cells are the basic structural units in crystals, though it has been suggested that the co-existence of various clusters may be the universal structural feature in MG. Therefore, it is a challenge to detect microstructures of MG even at the short-range scale by directly using synchrotron radiation techniques, such as X-ray diffraction and X-ray absorption methods. Here, a feasible scheme is developed where some state-of-the-art synchrotron radiation-based experiments can be combined with simulations to investigate the microstructure in MG. By studying a typical MG composition (Zr70Pd30, it is found that various clusters do co-exist in its microstructure, and icosahedral-like clusters are the popular structural units. This is the structural origin where there is precipitation of an icosahedral quasicrystalline phase prior to phase transformation from glass to crystal when heating Zr70Pd30 MG.

  18. An acceleration technique for the Gauss-Seidel method applied to symmetric linear systems

    Directory of Open Access Journals (Sweden)

    Jesús Cajigas

    2014-06-01

    Full Text Available A preconditioning technique to improve the convergence of the Gauss-Seidel method applied to symmetric linear systems while preserving symmetry is proposed. The preconditioner is of the form I + K and can be applied an arbitrary number of times. It is shown that under certain conditions the application of the preconditioner a finite number of steps reduces the matrix to a diagonal. A series of numerical experiments using matrices from spatial discretizations of partial differential equations demonstrates that both versions of the preconditioner, point and block version, exhibit lower iteration counts than its non-symmetric version. Resumen. Se propone una técnica de precondicionamiento para mejorar la convergencia del método Gauss-Seidel aplicado a sistemas lineales simétricos pero preservando simetría. El precondicionador es de la forma I + K y puede ser aplicado un número arbitrario de veces. Se demuestra que bajo ciertas condiciones la aplicación del precondicionador un número finito de pasos reduce la matriz del sistema precondicionado a una diagonal. Una serie de experimentos con matrices que provienen de la discretización de ecuaciones en derivadas parciales muestra que ambas versiones del precondicionador, por punto y por bloque, muestran un menor número de iteraciones en comparación con la versión que no preserva simetría.

  19. Personnel contamination protection techniques applied during the TMI-2 [Three Mile Island Unit 2] cleanup

    International Nuclear Information System (INIS)

    Hildebrand, J.E.

    1988-01-01

    The severe damage to the Three Mile Island Unit 2 (TMI-2) core and the subsequent discharge of reactor coolant to the reactor and auxiliary buildings resulted in extremely hostile radiological environments in the TMI-2 plant. High fission product surface contamination and radiation levels necessitated the implementation of innovative techniques and methods in performing cleanup operations while assuring effective as low as reasonably achievable (ALARA) practices. The approach utilized by GPU Nuclear throughout the cleanup in applying protective clothing requirements was to consider the overall health risk to the worker including factors such as cardiopulmonary stress, visual and hearing acuity, and heat stress. In applying protective clothing requirements, trade-off considerations had to be made between preventing skin contaminations and possibly overprotecting the worker, thus impacting his ability to perform his intended task at maximum efficiency and in accordance with ALARA principles. The paper discusses the following topics: protective clothing-general use, beta protection, skin contamination, training, personnel access facility, and heat stress

  20. MULTIVARIATE TECHNIQUES APPLIED TO EVALUATION OF LIGNOCELLULOSIC RESIDUES FOR BIOENERGY PRODUCTION

    Directory of Open Access Journals (Sweden)

    Thiago de Paula Protásio

    2013-12-01

    Full Text Available http://dx.doi.org/10.5902/1980509812361The evaluation of lignocellulosic wastes for bioenergy production demands to consider several characteristicsand properties that may be correlated. This fact demands the use of various multivariate analysis techniquesthat allow the evaluation of relevant energetic factors. This work aimed to apply cluster analysis and principalcomponents analyses for the selection and evaluation of lignocellulosic wastes for bioenergy production.8 types of residual biomass were used, whose the elemental components (C, H, O, N, S content, lignin, totalextractives and ashes contents, basic density and higher and lower heating values were determined. Bothmultivariate techniques applied for evaluation and selection of lignocellulosic wastes were efficient andsimilarities were observed between the biomass groups formed by them. Through the interpretation of thefirst principal component obtained, it was possible to create a global development index for the evaluationof the viability of energetic uses of biomass. The interpretation of the second principal component alloweda contrast between nitrogen and sulfur contents with oxygen content.

  1. Applying the GNSS Volcanic Ash Plume Detection Technique to Consumer Navigation Receivers

    Science.gov (United States)

    Rainville, N.; Palo, S.; Larson, K. M.

    2017-12-01

    Global Navigation Satellite Systems (GNSS) such as the Global Positioning System (GPS) rely on predictably structured and constant power RF signals to fulfill their primary use for navigation and timing. When the received strength of GNSS signals deviates from the expected baseline, it is typically due to a change in the local environment. This can occur when signal reflections from the ground are modified by changes in snow or soil moisture content, as well as by attenuation of the signal from volcanic ash. This effect allows GNSS signals to be used as a source for passive remote sensing. Larson et al. (2017) have developed a detection technique for volcanic ash plumes based on the attenuation seen at existing geodetic GNSS sites. Since these existing networks are relatively sparse, this technique has been extended to use lower cost consumer GNSS receiver chips to enable higher density measurements of volcanic ash. These low-cost receiver chips have been integrated into a fully stand-alone sensor, with independent power, communications, and logging capabilities as part of a Volcanic Ash Plume Receiver (VAPR) network. A mesh network of these sensors transmits data to a local base-station which then streams the data real-time to a web accessible server. Initial testing of this sensor network has uncovered that a different detection approach is necessary when using consumer GNSS receivers and antennas. The techniques to filter and process the lower quality data from consumer receivers will be discussed and will be applied to initial results from a functioning VAPR network installation.

  2. Mobilisation of toxic trace elements under various beach nourishments

    International Nuclear Information System (INIS)

    Pit, Iris R.; Dekker, Stefan C.; Kanters, Tobias J.; Wassen, Martin J.; Griffioen, Jasper

    2017-01-01

    To enhance protection and maintain wide beaches for recreation, beaches are replenished with sand: so-called beach nourishments. We compared four sites: two traditional beach nourishments, a mega beach nourishment and a reference without beach nourishment. Two sites contain calcareous-rich sand, whereas the other two sites have calcareous-poor sand. We aimed to understand hydrogeochemical processes to indicate factors critical for the mobility of trace elements at nourishments. We therefore analysed the chemical characteristics of sediment and pore water to ascertain the main drivers that mobilise toxic trace elements. With Dutch Quality Standards for soil and groundwater, the characteristics of sediment and pore water were compared to Target Values (the values at which there is a sustainable soil quality) and Intervention Values (the threshold above which the soil's functions are at risk). The pore water characteristics revealed that Target Values were regularly exceeded, especially for the nourishment sites and mainly for Mo (78%), Ni (24%), Cr (55%), and As (21%); Intervention Values for shallow groundwater were occasionally exceeded for As (2%), Cr (2%) and Zn (2%). The sediment characteristics did not exceed the Target Values and showed that trace elements were mainly present in the fine fraction of <150 μm. The oxidation of sulphide minerals such as pyrite resulted into the elevated concentration for all nourishment sites, especially when an unsaturated zone was present and influence of rainwater was apparent. To prevent trace metal mobility at a mega beach nourishment it is important to retain seawater influences and limit oxidation processes. In this respect, a shoreface nourishment is recommended rather than a mega beach nourishment with a thick unsaturated zone. Consequently, we conclude that whether a site is carbonate-rich or carbonate-poor is unimportant, as the influence of seawater will prevent decalcification, creating a low risk of

  3. Learning mediastinoscopy: the need for education, experience and modern techniques--interdependency of the applied technique and surgeon's training level.

    Science.gov (United States)

    Walles, Thorsten; Friedel, Godehard; Stegherr, Tobias; Steger, Volker

    2013-04-01

    Mediastinoscopy represents the gold standard for invasive mediastinal staging. While learning and teaching the surgical technique are challenging due to the limited accessibility of the operation field, both benefited from the implementation of video-assisted techniques. However, it has not been established yet whether video-assisted mediastinoscopy improves the mediastinal staging in itself. Retrospective single-centre cohort analysis of 657 mediastinoscopies performed at a specialized tertiary care thoracic surgery unit from 1994 to 2006. The number of specimens obtained per procedure and per lymph node station (2, 4, 7, 8 for mediastinoscopy and 2-9 for open lymphadenectomy), the number of lymph node stations examined, sensitivity and negative predictive value with a focus on the technique employed (video-assisted vs standard technique) and the surgeon's experience were calculated. Overall sensitivity was 60%, accuracy was 90% and negative predictive value 88%. With the conventional technique, experience alone improved sensitivity from 49 to 57% and it was predominant at the paratracheal right region (from 62 to 82%). But with the video-assisted technique, experienced surgeons rose sensitivity from 57 to 79% in contrast to inexperienced surgeons who lowered sensitivity from 49 to 33%. We found significant differences concerning (i) the total number of specimens taken, (ii) the amount of lymph node stations examined, (iii) the number of specimens taken per lymph node station and (iv) true positive mediastinoscopies. The video-assisted technique can significantly improve the results of mediastinoscopy. A thorough education on the modern video-assisted technique is mandatory for thoracic surgeons until they can fully exhaust its potential.

  4. A simple pulse shape discrimination technique applied to a silicon strip detector

    International Nuclear Information System (INIS)

    Figuera, P.; Lu, J.; Amorini, F.; Cardella, G.; DiPietro, A.; Papa, M.; Musumarra, A.; Pappalardo, G.; Rizzo, F.; Tudisco, S.

    2001-01-01

    Full text: Since the early sixties, it has been known that the shape of signals from solid state detectors can be used for particle identification. Recently, this idea has been revised in a group of papers where it has been shown that the shape of current signals from solid state detectors is mainly governed by the combination of plasma erosion time and charge carrier collection time effects. We will present the results of a systematic study on a pulse shape identification method which, contrary to the techniques proposed, is based on the use of the same electronic chain normally used in the conventional time of flight technique. The method is based on the use of charge preamplifiers, low polarization voltages (i.e. just above full depletion ones), rear side injection of the incident particles, and on a proper setting of the constant fraction discriminators which enhances the dependence of the timing output on the rise time of the input signals (which depends on the charge and energy of the incident ions). The method has been applied to an annular Si strip detector with an inner radius of about 16 mm and an outer radius of about 88 mm. The detector, manufactured by Eurisys Measures (Type Ips.73.74.300.N9), is 300 microns thick and consists of 8 independent sectors each divided into 9 circular strips. On beam tests have been performed at the cyclotron of the Laboratori Nazionali del Sud in Catania using a 25.7 MeV/nucleon 58 Ni beam impinging on a 51 V and 45 Sc composite target. Excellent charge identification from H up to the Ni projectile has been observed and typical charge identification thresholds are: ∼ 1.7 MeV/nucleon for Z ≅ 6, ∼ 3.0 MeV/nucleon for Z ≅ 11, and ∼ 5.5 MeV/nucleon for Z ≅ 20. Isotope identification up to A ≅ 13 has been observed with an energy threshold of about 6 MeV/nucleon. The identification quality has been studied as a function of the constant fraction settings. The method has been applied to all the 72 independent strips

  5. Applying machine-learning techniques to Twitter data for automatic hazard-event classification.

    Science.gov (United States)

    Filgueira, R.; Bee, E. J.; Diaz-Doce, D.; Poole, J., Sr.; Singh, A.

    2017-12-01

    The constant flow of information offered by tweets provides valuable information about all sorts of events at a high temporal and spatial resolution. Over the past year we have been analyzing in real-time geological hazards/phenomenon, such as earthquakes, volcanic eruptions, landslides, floods or the aurora, as part of the GeoSocial project, by geo-locating tweets filtered by keywords in a web-map. However, not all the filtered tweets are related with hazard/phenomenon events. This work explores two classification techniques for automatic hazard-event categorization based on tweets about the "Aurora". First, tweets were filtered using aurora-related keywords, removing stop words and selecting the ones written in English. For classifying the remaining between "aurora-event" or "no-aurora-event" categories, we compared two state-of-art techniques: Support Vector Machine (SVM) and Deep Convolutional Neural Networks (CNN) algorithms. Both approaches belong to the family of supervised learning algorithms, which make predictions based on labelled training dataset. Therefore, we created a training dataset by tagging 1200 tweets between both categories. The general form of SVM is used to separate two classes by a function (kernel). We compared the performance of four different kernels (Linear Regression, Logistic Regression, Multinomial Naïve Bayesian and Stochastic Gradient Descent) provided by Scikit-Learn library using our training dataset to build the SVM classifier. The results shown that the Logistic Regression (LR) gets the best accuracy (87%). So, we selected the SVM-LR classifier to categorise a large collection of tweets using the "dispel4py" framework.Later, we developed a CNN classifier, where the first layer embeds words into low-dimensional vectors. The next layer performs convolutions over the embedded word vectors. Results from the convolutional layer are max-pooled into a long feature vector, which is classified using a softmax layer. The CNN's accuracy

  6. Advanced nondestructive techniques applied for the detection of discontinuities in aluminum foams

    Science.gov (United States)

    Katchadjian, Pablo; García, Alejandro; Brizuela, Jose; Camacho, Jorge; Chiné, Bruno; Mussi, Valerio; Britto, Ivan

    2018-04-01

    Metal foams are finding an increasing range of applications by their lightweight structure and physical, chemical and mechanical properties. Foams can be used to fill closed moulds for manufacturing structural foam parts of complex shape [1]; foam filled structures are expected to provide good mechanical properties and energy absorption capabilities. The complexity of the foaming process and the number of parameters to simultaneously control, demand a preliminary and hugely wide experimental activity to manufacture foamed components with a good quality. That is why there are many efforts to improve the structure of foams, in order to obtain a product with good properties. The problem is that even for seemingly identical foaming conditions, the effective foaming can vary significantly from one foaming trial to another. The variation of the foams often is related by structural imperfections, joining region (foam-foam or foam-wall mold) or difficulties in achieving a complete filling of the mould. That is, in a closed mold, the result of the mold filling and its structure or defects are not known a priori and can eventually vary significantly. These defects can cause a drastic deterioration of the mechanical properties [2] and lead to a low performance in its application. This work proposes the use of advanced nondestructive techniques for evaluating the foam distribution after filling the mold to improve the manufacturing process. To achieved this purpose ultrasonic technique (UT) and cone beam computed tomography (CT) were applied on plate and structures of different thicknesses filled with foam of different porosity. UT was carried out on transmission mode with low frequency air-coupled transducers [3], in focused and unfocused configurations.

  7. Situational Awareness Applied to Geology Field Mapping using Integration of Semantic Data and Visualization Techniques

    Science.gov (United States)

    Houser, P. I. Q.

    2017-12-01

    21st century earth science is data-intensive, characterized by heterogeneous, sometimes voluminous collections representing phenomena at different scales collected for different purposes and managed in disparate ways. However, much of the earth's surface still requires boots-on-the-ground, in-person fieldwork in order to detect the subtle variations from which humans can infer complex structures and patterns. Nevertheless, field experiences can and should be enabled and enhanced by a variety of emerging technologies. The goal of the proposed research project is to pilot test emerging data integration, semantic and visualization technologies for evaluation of their potential usefulness in the field sciences, particularly in the context of field geology. The proposed project will investigate new techniques for data management and integration enabled by semantic web technologies, along with new techniques for augmented reality that can operate on such integrated data to enable in situ visualization in the field. The research objectives include: Develop new technical infrastructure that applies target technologies to field geology; Test, evaluate, and assess the technical infrastructure in a pilot field site; Evaluate the capabilities of the systems for supporting and augmenting field science; and Assess the generality of the system for implementation in new and different types of field sites. Our hypothesis is that these technologies will enable what we call "field science situational awareness" - a cognitive state formerly attained only through long experience in the field - that is highly desirable but difficult to achieve in time- and resource-limited settings. Expected outcomes include elucidation of how, and in what ways, these technologies are beneficial in the field; enumeration of the steps and requirements to implement these systems; and cost/benefit analyses that evaluate under what conditions the investments of time and resources are advisable to construct

  8. The simulation of Typhoon-induced coastal inundation in Busan, South Korea applying the downscaling technique

    Science.gov (United States)

    Jang, Dongmin; Park, Junghyun; Yuk, Jin-Hee; Joh, MinSu

    2017-04-01

    Due to typhoons, the south coastal cities including Busan in South Korea coastal are very vulnerable to a surge, wave and corresponding coastal inundation, and are affected every year. In 2016, South Korea suffered tremendous damage by typhoon 'Chaba', which was developed near east-north of Guam on Sep. 28 and had maximum 10-minute sustained wind speed of about 50 m/s, 1-minute sustained wind speed of 75 m/s and a minimum central pressure of 905 hpa. As 'Chaba', which is the strongest since typhoon 'Maemi' in 2003, hit South Korea on Oct. 5, it caused a massive economic and casualty damage to Ulsan, Gyeongju and Busan in South Korea. In particular, the damage of typhoon-induced coastal inundation in Busan, where many high-rise buildings and residential areas are concentrated near coast, was serious. The coastal inundation could be more affected by strong wind-induced wave than surge. In fact, it was observed that the surge height was about 1 m averagely and a significant wave height was about 8 m at coastal sea nearby Busan on Oct. 5 due to 'Chaba'. Even though the typhoon-induced surge elevated the sea level, the typhoon-induced long period wave with wave period of more than 15s could play more important role in the inundation. The present work simulated the coastal inundation induced by 'Chaba' in Busan, South Korea considering the effects of typhoon-induced surge and wave. For 'Chaba' hindcast, high resolution Weather Research and Forecasting model (WRF) was applied using a reanalysis data produced by NCEP (FNL 0.25 degree) on the boundary and initial conditions, and was validated by the observation of wind speed, direction and pressure. The typhoon-induced coastal inundation was simulated by an unstructured gird model, Finite Volume Community Ocean Model (FVCOM), which is fully current-wave coupled model. To simulate the wave-induced inundation, 1-way downscaling technique of multi domain was applied. Firstly, a mother's domain including Korean peninsula was

  9. Applying squeezing technique to clay-rocks: lessons learned from ten years experiments at Mont Terri

    International Nuclear Information System (INIS)

    Fernandez, A. M.; Melon, A.; Sanchez-Ledesma, D.M.; Tournassat, C.; Gaucher, E.; Astudillo, J.; Vinsot, A.

    2012-01-01

    Document available in extended abstract form only. Argillaceous formations of low permeability are considered in several countries as potential host rocks for the disposal of high level radioactive wastes (HLRW). In order to determine their suitability for waste disposal, evaluations of the hydro-geochemistry and transport mechanisms from such geologic formations to the biosphere must be undertaken. The migration of radionuclides through the geosphere will occur predominantly in the aqueous phase, and hence the pore water chemistry plays an important role in determining ion diffusion characteristics in argillaceous formations. Consequently, a great effort has been made to characterise the pore water chemistry in clay-rocks formations. In the last 10 years various techniques were developed for determining pore water composition of clay-rocks including both direct and indirect methods: 1) In situ pore water sampling (water and gas) from sealed boreholes (Pearson et al., 2003; Vinsot et al. 2008); 2) Laboratory pore water sampling from unaltered core samples by the squeezing technique at high pressures (Fernandez et al., 2009); and 3) Characterization of the water chemistry by geochemical modelling (Gaucher et al. 2009). Pore water chemistry in clay-rocks and extraction techniques were documented and reviewed in different studies (Sacchi et al., 2001). Recovering pristine pore water from low permeable and low water content systems is very difficult and sometimes impossible. Besides, uncertainties are associated to each method used for the pore water characterization. In this paper, a review about the high pressure squeezing technique applied to indurate clay-rocks was performed. For this purpose, the experimental work on Opalinus Clay at the Mont Terri Research Laboratory during the last ten years was evaluated. A complete discussion was made about different issues such as: a) why is necessary to obtain the pore water by squeezing in the context of radioactive waste

  10. Advanced examination techniques applied to the qualification of critical welds for the ITER correction coils

    CERN Document Server

    Sgobba, Stefano; Libeyre, Paul; Marcinek, Dawid Jaroslaw; Piguiet, Aline; Cécillon, Alexandre

    2015-01-01

    The ITER correction coils (CCs) consist of three sets of six coils located in between the toroidal (TF) and poloidal field (PF) magnets. The CCs rely on a Cable-in-Conduit Conductor (CICC), whose supercritical cooling at 4.5 K is provided by helium inlets and outlets. The assembly of the nozzles to the stainless steel conductor conduit includes fillet welds requiring full penetration through the thickness of the nozzle. Static and cyclic stresses have to be sustained by the inlet welds during operation. The entire volume of helium inlet and outlet welds, that are submitted to the most stringent quality levels of imperfections according to standards in force, is virtually uninspectable with sufficient resolution by conventional or computed radiography or by Ultrasonic Testing. On the other hand, X-ray computed tomography (CT) was successfully applied to inspect the full weld volume of several dozens of helium inlet qualification samples. The extensive use of CT techniques allowed a significant progress in the ...

  11. Spatial analysis techniques applied to uranium prospecting in Chihuahua State, Mexico

    Science.gov (United States)

    Hinojosa de la Garza, Octavio R.; Montero Cabrera, María Elena; Sanín, Luz H.; Reyes Cortés, Manuel; Martínez Meyer, Enrique

    2014-07-01

    To estimate the distribution of uranium minerals in Chihuahua, the advanced statistical model "Maximun Entropy Method" (MaxEnt) was applied. A distinguishing feature of this method is that it can fit more complex models in case of small datasets (x and y data), as is the location of uranium ores in the State of Chihuahua. For georeferencing uranium ores, a database from the United States Geological Survey and workgroup of experts in Mexico was used. The main contribution of this paper is the proposal of maximum entropy techniques to obtain the mineral's potential distribution. For this model were used 24 environmental layers like topography, gravimetry, climate (worldclim), soil properties and others that were useful to project the uranium's distribution across the study area. For the validation of the places predicted by the model, comparisons were done with other research of the Mexican Service of Geological Survey, with direct exploration of specific areas and by talks with former exploration workers of the enterprise "Uranio de Mexico". Results. New uranium areas predicted by the model were validated, finding some relationship between the model predictions and geological faults. Conclusions. Modeling by spatial analysis provides additional information to the energy and mineral resources sectors.

  12. Applying Toyota production system techniques for medication delivery: improving hospital safety and efficiency.

    Science.gov (United States)

    Newell, Terry L; Steinmetz-Malato, Laura L; Van Dyke, Deborah L

    2011-01-01

    The inpatient medication delivery system used at a large regional acute care hospital in the Midwest had become antiquated and inefficient. The existing 24-hr medication cart-fill exchange process with delivery to the patients' bedside did not always provide ordered medications to the nursing units when they were needed. In 2007 the principles of the Toyota Production System (TPS) were applied to the system. Project objectives were to improve medication safety and reduce the time needed for nurses to retrieve patient medications. A multidisciplinary team was formed that included representatives from nursing, pharmacy, informatics, quality, and various operational support departments. Team members were educated and trained in the tools and techniques of TPS, and then designed and implemented a new pull system benchmarking the TPS Ideal State model. The newly installed process, providing just-in-time medication availability, has measurably improved delivery processes as well as patient safety and satisfaction. Other positive outcomes have included improved nursing satisfaction, reduced nursing wait time for delivered medications, and improved efficiency in the pharmacy. After a successful pilot on two nursing units, the system is being extended to the rest of the hospital. © 2010 National Association for Healthcare Quality.

  13. Statistical Techniques Applied to Aerial Radiometric Surveys (STAARS): cluster analysis. National Uranium Resource Evaluation

    International Nuclear Information System (INIS)

    Pirkle, F.L.; Stablein, N.K.; Howell, J.A.; Wecksung, G.W.; Duran, B.S.

    1982-11-01

    One objective of the aerial radiometric surveys flown as part of the US Department of Energy's National Uranium Resource Evaluation (NURE) program was to ascertain the regional distribution of near-surface radioelement abundances. Some method for identifying groups of observations with similar radioelement values was therefore required. It is shown in this report that cluster analysis can identify such groups even when no a priori knowledge of the geology of an area exists. A method of convergent k-means cluster analysis coupled with a hierarchical cluster analysis is used to classify 6991 observations (three radiometric variables at each observation location) from the Precambrian rocks of the Copper Mountain, Wyoming, area. Another method, one that combines a principal components analysis with a convergent k-means analysis, is applied to the same data. These two methods are compared with a convergent k-means analysis that utilizes available geologic knowledge. All three methods identify four clusters. Three of the clusters represent background values for the Precambrian rocks of the area, and one represents outliers (anomalously high 214 Bi). A segmentation of the data corresponding to geologic reality as discovered by other methods has been achieved based solely on analysis of aerial radiometric data. The techniques employed are composites of classical clustering methods designed to handle the special problems presented by large data sets. 20 figures, 7 tables

  14. The Study of Mining Activities and their Influences in the Almaden Region Applying Remote Sensing Techniques

    International Nuclear Information System (INIS)

    Rico, C.; Schmid, T.; Millan, R.; Gumuzzio, J.

    2010-01-01

    This scientific-technical report is a part of an ongoing research work carried out by Celia Rico Fraile in order to obtain the Diploma of Advanced Studies as part of her PhD studies. This work has been developed in collaboration with the Faculty of Science at The Universidad Autonoma de Madrid and the Department of Environment at CIEMAT. The main objective of this work was the characterization and classification of land use in Almaden (Ciudad Real) during cinnabar mineral exploitation and after mining activities ceased in 2002, developing a methodology focused on the integration of remote sensing techniques applying multispectral and hyper spectral satellite data. By means of preprocessing and processing of data from the satellite images as well as data obtained from field campaigns, a spectral library was compiled in order to obtain representative land surfaces within the study area. Monitoring results show that the distribution of areas affected by mining activities is rapidly diminishing in recent years. (Author) 130 refs

  15. Coldness applied to plastic engineering techniques and rooms; Le froid applique aux techniques de la plasturgie et a ses locaux

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    This technical dossier is the result of a collaboration between the CFE, EdF Industrie and the French federation of plastic engineering. It aims at answering all questions relative to plastic materials processing: 1 - general study on the economical aspects of plastic engineering, plastic materials, and manufacturing processes; 2 - the different cold processing techniques (air cooling and refrigerating systems); 3 - the main transformation processes for thermo-plastic materials and the advantage of cooling techniques; 4 - the environmental conditioning of rooms (clean rooms); 5 - examples of realizations. (J.S.)

  16. Political Participation Online: The Replacement and the Mobilisation Hypotheses Revisited

    DEFF Research Database (Denmark)

    Jensen, Jakob Linaa

    2013-01-01

    This article discusses the state of political participation online more than ten years after the Internet’s great popular breakthrough as an everyday medium. Denmark is used as a case study to critically re-examine the frequently discussed replacement and mobilisation hypotheses on behalf of the ...... participation, efficacy and social capital seem to have less impact on online political participation. In the end, these findings are related to more overall discussions on the democratising potential of the Internet.......This article discusses the state of political participation online more than ten years after the Internet’s great popular breakthrough as an everyday medium. Denmark is used as a case study to critically re-examine the frequently discussed replacement and mobilisation hypotheses on behalf...... of the Internet. The pure replacement hypothesis is rejected. Instead, it is found that the Internet still supplements rather than replaces other media, even among heavy Internet users. The Internet is one among several media used by ‘media omnivores’, and political participation online supplements rather than...

  17. Mobilisation of toxic elements in the human respiratory system

    International Nuclear Information System (INIS)

    Pinheiro, T.; Alves, L.C.; Palhano, M.J.; Bugalho de Almeida, A.

    2001-01-01

    The fate of respired particles in the respiratory system is inferred through the chemical characterisation of individual particles at the tracheal and bronchial mucosas, and the accumulation of toxic elements in lung alveoli and lymph nodes. The particles and tissue elemental distributions were identified and characterised using micro-PIXE elemental mapping of thin frozen sections using the ITN Nuclear Microprobe facility. Significant particle deposits are found at the distal respiratory tract. Al, Si, Ti, V, Cr, Fe, Ni, Cu and Zn are elements detected at these accumulation areas. The elemental distributions in the different cellular environments of lymph nodes vary. The major compartments for Al, Si, Ti, Fe and Cr are the phagocytic cells and capsule of lymph nodes, while V and Ni are in the cortex and paracortex medullar areas which retain more than 70% of these two elements, suggesting high solubility of the latter in the cellular milieu. The elemental mobilisation from particles or deposits to surrounding tissues at the respiratory ducts evidences patterns of diffusion and removal that are different than those for elements in the respiratory tract. Mobilisation of elements such as V, Cr and Ni is more relevant at alveoli areas where gaseous exchange takes place. The apparent high solubility of V and Ni in the respiratory tract tissue points towards a deviation of the lymphatic system filtering efficiency for these elements when compared to others

  18. Distributed leadership to mobilise capacity for accreditation research.

    Science.gov (United States)

    Greenfield, David; Braithwaite, Jeffrey; Pawsey, Marjorie; Johnson, Brian; Robinson, Maureen

    2009-01-01

    Inquiries into healthcare organisations have highlighted organisational or system failure, attributed to poor responses to early warning signs. One response, and challenge, is for professionals and academics to build capacity for quality and safety research to provide evidence for improved systems. However, such collaborations and capacity building do not occur easily as there are many stakeholders. Leadership is necessary to unite differences into a common goal. The lessons learned and principles arising from the experience of providing distributed leadership to mobilise capacity for quality and safety research when researching health care accreditation in Australia are presented. A case study structured by temporal bracketing that presents a narrative account of multi-stakeholder perspectives. Data are collected using in-depth informal interviews with key informants and ethno-document analysis. Distributed leadership enabled a collaborative research partnership to be realised. The leadership harnessed the relative strengths of partners and accounted for, and balanced, the interests of stakeholder participants involved. Across three phases, leadership and the research partnership was enacted: identifying partnerships, bottom-up engagement and enacting the research collaboration. Two principles to maximise opportunities to mobilise capacity for quality and safety research have been identified. First, successful collaborations, particularly multi-faceted inter-related partnerships, require distributed leadership. Second, the leadership-stakeholder enactment can promote reciprocity so that the collaboration becomes mutually reinforcing and beneficial to partners. The paper addresses the need to understand the practice and challenges of distributed leadership and how to replicate positive practices to implement patient safety research.

  19. Investigation about the efficiency of the bioaugmentation technique when applied to diesel oil contaminated soils

    Directory of Open Access Journals (Sweden)

    Adriano Pinto Mariano

    2009-10-01

    Full Text Available This work investigated the efficiency of the bioaugmentation technique when applied to diesel oil contaminated soils collected at three service stations. Batch biodegradation experiments were carried out in Bartha biometer flasks (250 mL used to measure the microbial CO2 production. Biodegradation efficiency was also measured by quantifying the concentration of hydrocarbons. In addition to the biodegradation experiments, the capability of the studied cultures and the native microorganisms to biodegrade the diesel oil purchased from a local service station, was verified using a technique based on the redox indicator 2,6 -dichlorophenol indophenol (DCPIP. Results obtained with this test showed that the inocula used in the biodegradation experiments were able to degrade the diesel oil and the tests carried out with the native microorganisms indicated that these soils had a microbiota adapted to degrade the hydrocarbons. In general, no gain was obtained with the addition of microorganisms or even negative effects were observed in the biodegradation experiments.Este trabalho investigou a eficiência da técnica do bioaumento quando aplicada a solos contaminados com óleo diesel coletados em três postos de combustíveis. Experimentos de biodegradação foram realizados em frascos de Bartha (250 mL, usados para medir a produção microbiana de CO2. A eficiência de biodegradação também foi quantificada pela concentração de hidrocarbonetos. Conjuntamente aos experimentos de biodegradação, a capacidade das culturas estudadas e dos microrganismos nativos em biodegradar óleo diesel comprado de um posto de combustíveis local, foi verificada utilizando-se a técnica baseada no indicador redox 2,6 - diclorofenol indofenol (DCPIP. Resultados obtidos com esse teste mostraram que os inóculos empregados nos experimentos de biodegradação foram capazes de biodegradar óleo diesel e os testes com os microrganismos nativos indicaram que estes solos

  20. Manipulation and mobilisation for neck pain contrasted against an inactive control or another active treatment

    NARCIS (Netherlands)

    Gross, Anita; Langevin, Pierre; Burnie, Stephen J.; Bédard-Brochu, Marie-Sophie; Empey, Brian; Dugas, Estelle; Faber-Dobrescu, Michael; Andres, Cristy; Graham, Nadine; Goldsmith, Charles H.; Brønfort, Gert; Hoving, Jan L.; LeBlanc, Francis

    2015-01-01

    Manipulation and mobilisation are commonly used to treat neck pain. This is an update of a Cochrane review first published in 2003, and previously updated in 2010. To assess the effects of manipulation or mobilisation alone compared wiith those of an inactive control or another active treatment on

  1. Multidisciplinary Design Techniques Applied to Conceptual Aerospace Vehicle Design. Ph.D. Thesis Final Technical Report

    Science.gov (United States)

    Olds, John Robert; Walberg, Gerald D.

    1993-01-01

    Multidisciplinary design optimization (MDO) is an emerging discipline within aerospace engineering. Its goal is to bring structure and efficiency to the complex design process associated with advanced aerospace launch vehicles. Aerospace vehicles generally require input from a variety of traditional aerospace disciplines - aerodynamics, structures, performance, etc. As such, traditional optimization methods cannot always be applied. Several multidisciplinary techniques and methods were proposed as potentially applicable to this class of design problem. Among the candidate options are calculus-based (or gradient-based) optimization schemes and parametric schemes based on design of experiments theory. A brief overview of several applicable multidisciplinary design optimization methods is included. Methods from the calculus-based class and the parametric class are reviewed, but the research application reported focuses on methods from the parametric class. A vehicle of current interest was chosen as a test application for this research. The rocket-based combined-cycle (RBCC) single-stage-to-orbit (SSTO) launch vehicle combines elements of rocket and airbreathing propulsion in an attempt to produce an attractive option for launching medium sized payloads into low earth orbit. The RBCC SSTO presents a particularly difficult problem for traditional one-variable-at-a-time optimization methods because of the lack of an adequate experience base and the highly coupled nature of the design variables. MDO, however, with it's structured approach to design, is well suited to this problem. The result of the application of Taguchi methods, central composite designs, and response surface methods to the design optimization of the RBCC SSTO are presented. Attention is given to the aspect of Taguchi methods that attempts to locate a 'robust' design - that is, a design that is least sensitive to uncontrollable influences on the design. Near-optimum minimum dry weight solutions are

  2. Study for applying microwave power saturation technique on fingernail/EPR dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Park, Byeong Ryong; Choi, Hoon; Nam, Hyun Ill; Lee, Byung Ill [Radiation Health Research Institute, Seoul (Korea, Republic of)

    2012-10-15

    There is growing recognition worldwide of the need to develop effective uses of dosimetry methods to assess unexpected exposure to radiation in the event of a large scale event. One of physically based dosimetry methods electron paramagnetic resonance (EPR) spectroscopy has been applied to perform retrospective radiation dosimetry using extracted samples of tooth enamel and nail(fingernail and toenail), following radiation accidents and exposures resulting from weapon use, testing, and production. Human fingernails are composed largely of a keratin, which consists of {alpha} helical peptide chains that are twisted into a left handed coil and strengthened by disulphide cross links. Ionizing radiation generates free radicals in the keratin matrix, and these radicals are stable over a relatively long period (days to weeks). Most importantly, the number of radicals is proportional to the magnitude of the dose over a wide dose range (0{approx}30 Gy). Also, dose can be estimated at four different locations on the human body, providing information on the homogeneity of the radiation exposure. And The results from EPR nail dosimetry are immediately available However, relatively large background signal (BKS) converted from mechanically induced signal (MIS) after cutting process of fingernail, normally overlaps with the radiation induced signal (RIS), make it difficult to estimate accurate dose accidental exposure. Therefore, estimation method using dose response curve was difficult to ensure reliability below 5 Gy. In this study, In order to overcome these disadvantages, we measured the reactions of RIS and BKS (MIS) according to the change of Microwave power level, and researched about the applicability of the Power saturation technique at low dose.

  3. Plasma-based techniques applied to the determination of metals and metalloids in atmospheric aerosols

    International Nuclear Information System (INIS)

    Smichowski, Patricia

    2011-01-01

    Full text: This lecture presents an overview of the research carried out by our group during the last decade on the determination of metals, metalloids, ions and species in atmospheric aerosols and related matrices using plasma-based techniques. In our first studies we explored the application of a size fractionation procedure and the subsequent determination of minor, major and trace elements in samples of deposited particles collected one day after the eruption of the Copahue Volcano, located in the Chile-Argentina border to assess the content of relevant elements with respect of the environment and the local population health. We employed a multi-technique approach (ICP-MS, XRD and NAA) to gain complete information of the characteristics of the sample. In addition to the study of ashes emitted for natural sources we also studied ashes of anthropogenic origin such as those arising from coal combustion in thermal power plants. For estimating the behavior and fate of elements in atmospheric particles and ashes we applied in this case a chemical fractionation procedure in order to establish the distribution of many elements amongst soluble, bound to carbonates, bound to oxides and bound to organic matter and environmental immobile fraction. Studies on the air quality of the mega-city of Buenos Aires were scarce and fragmentary and our objective was, and still is, to contribute to clarify key issues related to levels of crustal, toxic and potentially toxic elements in this air basin. Our findings were compared with average concentrations of metals and metalloids with results reported for other Latin American cities such as Sao Paulo, Mexico and Santiago de Chile. In this context, a series of studies were carried out since 2004 considering different sampling strategies to reflect local aspects of air pollution sources. In the last years, our interest was focused on the levels of traffic-related elements in the urban atmosphere. We have contributed with the first data

  4. Plasma-based techniques applied to the determination of metals and metalloids in atmospheric aerosols

    Energy Technology Data Exchange (ETDEWEB)

    Smichowski, Patricia, E-mail: smichows@cnea.gov.ar [Comision Nacional de Energia Atomica, Gerencia Quimica, Pcia de Buenos Aires (Argentina)

    2011-07-01

    Full text: This lecture presents an overview of the research carried out by our group during the last decade on the determination of metals, metalloids, ions and species in atmospheric aerosols and related matrices using plasma-based techniques. In our first studies we explored the application of a size fractionation procedure and the subsequent determination of minor, major and trace elements in samples of deposited particles collected one day after the eruption of the Copahue Volcano, located in the Chile-Argentina border to assess the content of relevant elements with respect of the environment and the local population health. We employed a multi-technique approach (ICP-MS, XRD and NAA) to gain complete information of the characteristics of the sample. In addition to the study of ashes emitted for natural sources we also studied ashes of anthropogenic origin such as those arising from coal combustion in thermal power plants. For estimating the behavior and fate of elements in atmospheric particles and ashes we applied in this case a chemical fractionation procedure in order to establish the distribution of many elements amongst soluble, bound to carbonates, bound to oxides and bound to organic matter and environmental immobile fraction. Studies on the air quality of the mega-city of Buenos Aires were scarce and fragmentary and our objective was, and still is, to contribute to clarify key issues related to levels of crustal, toxic and potentially toxic elements in this air basin. Our findings were compared with average concentrations of metals and metalloids with results reported for other Latin American cities such as Sao Paulo, Mexico and Santiago de Chile. In this context, a series of studies were carried out since 2004 considering different sampling strategies to reflect local aspects of air pollution sources. In the last years, our interest was focused on the levels of traffic-related elements in the urban atmosphere. We have contributed with the first data

  5. Trends in analytical techniques applied to particulate matter characterization: A critical review of fundaments and applications.

    Science.gov (United States)

    Galvão, Elson Silva; Santos, Jane Meri; Lima, Ana Teresa; Reis, Neyval Costa; Orlando, Marcos Tadeu D'Azeredo; Stuetz, Richard Michael

    2018-05-01

    Epidemiological studies have shown the association of airborne particulate matter (PM) size and chemical composition with health problems affecting the cardiorespiratory and central nervous systems. PM also act as cloud condensation nuclei (CNN) or ice nuclei (IN), taking part in the clouds formation process, and therefore can impact the climate. There are several works using different analytical techniques in PM chemical and physical characterization to supply information to source apportionment models that help environmental agencies to assess damages accountability. Despite the numerous analytical techniques described in the literature available for PM characterization, laboratories are normally limited to the in-house available techniques, which raises the question if a given technique is suitable for the purpose of a specific experimental work. The aim of this work consists of summarizing the main available technologies for PM characterization, serving as a guide for readers to find the most appropriate technique(s) for their investigation. Elemental analysis techniques like atomic spectrometry based and X-ray based techniques, organic and carbonaceous techniques and surface analysis techniques are discussed, illustrating their main features as well as their advantages and drawbacks. We also discuss the trends in analytical techniques used over the last two decades. The choice among all techniques is a function of a number of parameters such as: the relevant particles physical properties, sampling and measuring time, access to available facilities and the costs associated to equipment acquisition, among other considerations. An analytical guide map is presented as a guideline for choosing the most appropriated technique for a given analytical information required. Copyright © 2018 Elsevier Ltd. All rights reserved.

  6. Time-series-analysis techniques applied to nuclear-material accounting

    International Nuclear Information System (INIS)

    Pike, D.H.; Morrison, G.W.; Downing, D.J.

    1982-05-01

    This document is designed to introduce the reader to the applications of Time Series Analysis techniques to Nuclear Material Accountability data. Time series analysis techniques are designed to extract information from a collection of random variables ordered by time by seeking to identify any trends, patterns, or other structure in the series. Since nuclear material accountability data is a time series, one can extract more information using time series analysis techniques than by using other statistical techniques. Specifically, the objective of this document is to examine the applicability of time series analysis techniques to enhance loss detection of special nuclear materials. An introductory section examines the current industry approach which utilizes inventory differences. The error structure of inventory differences is presented. Time series analysis techniques discussed include the Shewhart Control Chart, the Cumulative Summation of Inventory Differences Statistics (CUSUM) and the Kalman Filter and Linear Smoother

  7. Applying data mining techniques to medical time series: an empirical case study in electroencephalography and stabilometry

    Directory of Open Access Journals (Sweden)

    A. Anguera

    2016-01-01

    This paper illustrates the application of different knowledge discovery techniques for the purposes of classification within the above domains. The accuracy of this application for the two classes considered in each case is 99.86% and 98.11% for epilepsy diagnosis in the electroencephalography (EEG domain and 99.4% and 99.1% for early-age sports talent classification in the stabilometry domain. The KDD techniques achieve better results than other traditional neural network-based classification techniques.

  8. Comparison of multivariate preprocessing techniques as applied to electronic tongue based pattern classification for black tea

    International Nuclear Information System (INIS)

    Palit, Mousumi; Tudu, Bipan; Bhattacharyya, Nabarun; Dutta, Ankur; Dutta, Pallab Kumar; Jana, Arun; Bandyopadhyay, Rajib; Chatterjee, Anutosh

    2010-01-01

    In an electronic tongue, preprocessing on raw data precedes pattern analysis and choice of the appropriate preprocessing technique is crucial for the performance of the pattern classifier. While attempting to classify different grades of black tea using a voltammetric electronic tongue, different preprocessing techniques have been explored and a comparison of their performances is presented in this paper. The preprocessing techniques are compared first by a quantitative measurement of separability followed by principle component analysis; and then two different supervised pattern recognition models based on neural networks are used to evaluate the performance of the preprocessing techniques.

  9. Final Aperture Superposition Technique applied to fast calculation of electron output factors and depth dose curves

    International Nuclear Information System (INIS)

    Faddegon, B.A.; Villarreal-Barajas, J.E.

    2005-01-01

    The Final Aperture Superposition Technique (FAST) is described and applied to accurate, near instantaneous calculation of the relative output factor (ROF) and central axis percentage depth dose curve (PDD) for clinical electron beams used in radiotherapy. FAST is based on precalculation of dose at select points for the two extreme situations of a fully open final aperture and a final aperture with no opening (fully shielded). This technique is different than conventional superposition of dose deposition kernels: The precalculated dose is differential in position of the electron or photon at the downstream surface of the insert. The calculation for a particular aperture (x-ray jaws or MLC, insert in electron applicator) is done with superposition of the precalculated dose data, using the open field data over the open part of the aperture and the fully shielded data over the remainder. The calculation takes explicit account of all interactions in the shielded region of the aperture except the collimator effect: Particles that pass from the open part into the shielded part, or visa versa. For the clinical demonstration, FAST was compared to full Monte Carlo simulation of 10x10,2.5x2.5, and 2x8 cm 2 inserts. Dose was calculated to 0.5% precision in 0.4x0.4x0.2 cm 3 voxels, spaced at 0.2 cm depth intervals along the central axis, using detailed Monte Carlo simulation of the treatment head of a commercial linear accelerator for six different electron beams with energies of 6-21 MeV. Each simulation took several hours on a personal computer with a 1.7 Mhz processor. The calculation for the individual inserts, done with superposition, was completed in under a second on the same PC. Since simulations for the pre calculation are only performed once, higher precision and resolution can be obtained without increasing the calculation time for individual inserts. Fully shielded contributions were largest for small fields and high beam energy, at the surface, reaching a maximum

  10. Mobilisering af barnets potentiale for en bedre fremtid

    DEFF Research Database (Denmark)

    Øland, Trine

    2014-01-01

    to the forming and education of the child, mobilising the child’s potential to secure the future and promote peace and international understanding. This article examines so far unexamined sources, i.e., 89 assessments of children’s book manuscripts from the private archives of Torben Gregersen (1911......Children’s books were one of the scenes where ‘progressive’ professionals - mostly teachers, psychologists and artists - around WWII fought the battle to change society through changed educational thinking. Especially after WWII it was acknowledged that children’s books could contribute...... development and national culture, and literary and aesthetic-artistic elements to a lesser extent. Thus, the article shows that the emergence of ‘progressive’ elements which in research on children’s literature normally are dated to the late 1960s, are not only present in the 1940s and 1950s...

  11. The mobilisation of sediment by demersal otter trawls.

    Science.gov (United States)

    O'Neill, F G; Summerbell, K

    2011-05-01

    The mobilisation of sediment by towed demersal fishing gears has been related to the release of nutrients, benthic infaunal mortality and the resuspension of phytoplankton cysts and copepod eggs. Hence, to understand the broader environmental and ecological implications of demersal fishing, it is important to be able to estimate accurately the amount of sediment put into the water column by towed gears. Experimental trials were carried out in the Moray Firth, Scotland, to measure the quantity of sediment remobilised by trawl gear components. It is demonstrated, for a given sediment type, that there is a relationship between the hydrodynamic drag of the gear element and the mass of sediment entrained behind it. A better understanding of this relationship and the hydrodynamic processes involved will lead to the development of accurate predictive models and aid the design of fishing gears of reduced impact. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

  12. Mobilisation of toxic trace elements under various beach nourishments.

    Science.gov (United States)

    Pit, Iris R; Dekker, Stefan C; Kanters, Tobias J; Wassen, Martin J; Griffioen, Jasper

    2017-12-01

    To enhance protection and maintain wide beaches for recreation, beaches are replenished with sand: so-called beach nourishments. We compared four sites: two traditional beach nourishments, a mega beach nourishment and a reference without beach nourishment. Two sites contain calcareous-rich sand, whereas the other two sites have calcareous-poor sand. We aimed to understand hydrogeochemical processes to indicate factors critical for the mobility of trace elements at nourishments. We therefore analysed the chemical characteristics of sediment and pore water to ascertain the main drivers that mobilise toxic trace elements. With Dutch Quality Standards for soil and groundwater, the characteristics of sediment and pore water were compared to Target Values (the values at which there is a sustainable soil quality) and Intervention Values (the threshold above which the soil's functions are at risk). The pore water characteristics revealed that Target Values were regularly exceeded, especially for the nourishment sites and mainly for Mo (78%), Ni (24%), Cr (55%), and As (21%); Intervention Values for shallow groundwater were occasionally exceeded for As (2%), Cr (2%) and Zn (2%). The sediment characteristics did not exceed the Target Values and showed that trace elements were mainly present in the fine fraction of <150 μm. The oxidation of sulphide minerals such as pyrite resulted into the elevated concentration for all nourishment sites, especially when an unsaturated zone was present and influence of rainwater was apparent. To prevent trace metal mobility at a mega beach nourishment it is important to retain seawater influences and limit oxidation processes. In this respect, a shoreface nourishment is recommended rather than a mega beach nourishment with a thick unsaturated zone. Consequently, we conclude that whether a site is carbonate-rich or carbonate-poor is unimportant, as the influence of seawater will prevent decalcification, creating a low risk of mobilisation

  13. Pregnancy increases mobilisation of lead from maternal skeleton

    International Nuclear Information System (INIS)

    Gulson, B.L.

    2000-01-01

    Lead is a neurotoxin that, even at low levels, is considered to result in neurobehavioural disorders such as cognitive deficits, learning disability and behavioural disturbances. The most recent study of Needleman et al. suggested an association between bone lead levels and antisocial and delinquent behaviour (Needleman et al., 1996). Although the neurobehavioural deficits associated with low-level lead exposure are best documented for early childhood exposures, the effects of lead on the developing nervous system are of concern. Lead readily crosses the placenta (Barltrop, 1969; Silbergeld, 1991) and changes in maternal blood lead potentially result in alterations to foetal exposure. Mobilisation of lead from body stores accumulated prior to pregnancy has been established in experimental animals (Buchet, 1977; Keller and Doherty, 1980). The cohort was to consist of 100 immigrants anticipated to provide 20 pregnant subjects who would be compared with two groups of control subjects: a matched immigrant nonpregnant control group and second-generation Australian pregnant controls. The pregnant subject also serves as her own control for a comparison of changes during pregnancy with those prior to conception. High precision lead isotopic compositions and lead concentrations were measured on: maternal blood and urine prenatally, monthly during pregnancy and post-pregnancy for 6 months; infant blood and urine for 6 months; and environmental measures sampled quarterly for 6-day duplicate diet, house dust and water, urban air and petrol. Results of this study confirm that lead is mobilised from skeletal stores at an accelerated rate during pregnancy and transferred to the foetus. This has implications for interpretations of neurobehavioural disorders attributed solely to post-natal exposure

  14. Element selective detection of molecular species applying chromatographic techniques and diode laser atomic absorption spectrometry.

    Science.gov (United States)

    Kunze, K; Zybin, A; Koch, J; Franzke, J; Miclea, M; Niemax, K

    2004-12-01

    Tunable diode laser atomic absorption spectroscopy (DLAAS) combined with separation techniques and atomization in plasmas and flames is presented as a powerful method for analysis of molecular species. The analytical figures of merit of the technique are demonstrated by the measurement of Cr(VI) and Mn compounds, as well as molecular species including halogen atoms, hydrogen, carbon and sulfur.

  15. Quantitative thoracic CT techniques in adults: can they be applied in the pediatric population?

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Soon Ho [Seoul National University Medical Research Center, Department of Radiology, Seoul National University College of Medicine, and Institute of Radiation Medicine, Seoul (Korea, Republic of); Goo, Jin Mo [Seoul National University Medical Research Center, Department of Radiology, Seoul National University College of Medicine, and Institute of Radiation Medicine, Seoul (Korea, Republic of); Seoul National University College of Medicine, Cancer Research Institute, Jongno-gu, Seoul (Korea, Republic of); Goo, Hyun Woo [University of Ulsan College of Medicine, Department of Radiology and Research Institute of Radiology, Asan Medical Center, Seoul (Korea, Republic of)

    2013-03-15

    With the rapid evolution of the multidetector row CT technique, quantitative CT has started to be used in clinical studies for revealing a heterogeneous entity of airflow limitation in chronic obstructive pulmonary disease that is caused by a combination of lung parenchymal destruction and remodeling of the small airways in adults. There is growing evidence of a good correlation between quantitative CT findings and pathological findings, pulmonary function test results and other clinical parameters. This article provides an overview of current quantitative thoracic CT techniques used in adults, and how to translate these CT techniques to the pediatric population. (orig.)

  16. Applied measuring techniques for the investigation of time-dependent flow phenomena in centrifugal compressors

    International Nuclear Information System (INIS)

    Hass, U.; Haupt, U.; Jansen, M.; Kassens, K.; Knapp, P.; Rautenberg, M.

    1978-01-01

    During the past 10 years new measuring techniques have been developed for the experimental investigation of highly loaded centrifugal compressors. These measuring techniques take into account the time dependency of the fluctuating physical quantities such as pressure, temperature, and velocity. Some key points of these experimental techniques are shown and explained in this paper. An important basis for such measurements is the accurate dynamic calibration of the measuring apparatus. In addition, some problems involved analyzing measured signals are dealt with and pressure measurements and their interpretation are shown. Finally optical, acoustical and vibrational measuring procedures are described which are additionally used for the investigation of non-stationary flow phenomena. (orig.) [de

  17. Neutron Filter Technique and its use for Fundamental and applied Investigations

    International Nuclear Information System (INIS)

    Gritzay, V.; Kolotyi, V.

    2008-01-01

    At Kyiv Research Reactor (KRR) the neutron filtered beam technique is used for more than 30 years and its development continues, the new and updated facilities for neutron cross section measurements provide the receipt of neutron cross sections with rather high accuracy: total neutron cross sections with accuracy 1% and better, neutron scattering cross sections with 3-6% accuracy. The main purpose of this paper is presentation of the neutron measurement techniques, developed at KRR, and demonstration some experimental results, obtained using these techniques

  18. Applying of Reliability Techniques and Expert Systems in Management of Radioactive Accidents

    International Nuclear Information System (INIS)

    Aldaihan, S.; Alhbaib, A.; Alrushudi, S.; Karazaitri, C.

    1998-01-01

    Accidents including radioactive exposure have variety of nature and size. This makes such accidents complex situations to be handled by radiation protection agencies or any responsible authority. The situations becomes worse with introducing advanced technology with high complexity that provide operator huge information about system working on. This paper discusses the application of reliability techniques in radioactive risk management. Event tree technique from nuclear field is described as well as two other techniques from nonnuclear fields, Hazard and Operability and Quality Function Deployment. The objective is to show the importance and the applicability of these techniques in radiation risk management. Finally, Expert Systems in the field of accidents management are explored and classified upon their applications

  19. Using wavelet denoising and mathematical morphology in the segmentation technique applied to blood cells images

    OpenAIRE

    Boix García, Macarena; Cantó Colomina, Begoña

    2013-01-01

    Accurate image segmentation is used in medical diagnosis since this technique is a noninvasive pre-processing step for biomedical treatment. In this work we present an efficient segmentation method for medical image analysis. In particular, with this method blood cells can be segmented. For that, we combine the wavelet transform with morphological operations. Moreover, the wavelet thresholding technique is used to eliminate the noise and prepare the image for suitable segmentation. In wavelet...

  20. Error analysis of the phase-shifting technique when applied to shadow moire

    International Nuclear Information System (INIS)

    Han, Changwoon; Han Bongtae

    2006-01-01

    An exact solution for the intensity distribution of shadow moire fringes produced by a broad spectrum light is presented. A mathematical study quantifies errors in fractional fringe orders determined by the phase-shifting technique, and its validity is corroborated experimentally. The errors vary cyclically as the distance between the reference grating and the specimen increases. The amplitude of the maximum error is approximately 0.017 fringe, which defines the theoretical limit of resolution enhancement offered by the phase-shifting technique

  1. Applying machine learning and image feature extraction techniques to the problem of cerebral aneurysm rupture

    Directory of Open Access Journals (Sweden)

    Steren Chabert

    2017-01-01

    Full Text Available Cerebral aneurysm is a cerebrovascular disorder characterized by a bulging in a weak area in the wall of an artery that supplies blood to the brain. It is relevant to understand the mechanisms leading to the apparition of aneurysms, their growth and, more important, leading to their rupture. The purpose of this study is to study the impact on aneurysm rupture of the combination of different parameters, instead of focusing on only one factor at a time as is frequently found in the literature, using machine learning and feature extraction techniques. This discussion takes relevance in the context of the complex decision that the physicians have to take to decide which therapy to apply, as each intervention bares its own risks, and implies to use a complex ensemble of resources (human resources, OR, etc. in hospitals always under very high work load. This project has been raised in our actual working team, composed of interventional neuroradiologist, radiologic technologist, informatics engineers and biomedical engineers, from Valparaiso public Hospital, Hospital Carlos van Buren, and from Universidad de Valparaíso – Facultad de Ingeniería and Facultad de Medicina. This team has been working together in the last few years, and is now participating in the implementation of an “interdisciplinary platform for innovation in health”, as part of a bigger project leaded by Universidad de Valparaiso (PMI UVA1402. It is relevant to emphasize that this project is made feasible by the existence of this network between physicians and engineers, and by the existence of data already registered in an orderly manner, structured and recorded in digital format. The present proposal arises from the description in nowadays literature that the actual indicators, whether based on morphological description of the aneurysm, or based on characterization of biomechanical factor or others, these indicators were shown not to provide sufficient information in order

  2. Effectiveness of joint mobilisation after cast immobilisation for ankle fracture: a protocol for a randomised controlled trial [ACTRN012605000143628

    Directory of Open Access Journals (Sweden)

    Haas Marion

    2006-05-01

    Full Text Available Abstract Background Passive joint mobilisation is a technique frequently used by physiotherapists to reduce pain, improve joint movement and facilitate a return to activities after injury, but its use after ankle fracture is currently based on limited evidence. The primary aim of this trial is to determine if adding joint mobilisation to a standard exercise programme is effective and cost-effective after cast immobilisation for ankle fracture in adults. Methods/Design Ninety participants will be recruited from the physiotherapy departments of three teaching hospitals and randomly allocated to treatment or control groups using a concealed procedure. All participants will perform an exercise programme. Participants in the treatment group will also receive joint mobilisation twice a week for four weeks. Blinded follow-up assessments will be conducted four, 12 and 24 weeks after randomisation. The primary outcome measures will be the Lower Extremity Functional Scale and the Assessment of Quality of Life. Secondary outcomes will include measures of impairments, activity limitation and participation. Data on the use of physiotherapy services and participants' out-of-pocket costs will be collected for the cost-effective and cost-utility analyses. To test the effects of treatment, between-group differences will be examined with analysis of covariance using a regression approach. The primary conclusions will be based on the four-week follow-up data. Discussion This trial incorporates features known to minimise bias. It uses a pragmatic design to reflect clinical practice and maximise generalisability. Results from this trial will contribute to an evidence-based approach for rehabilitation after ankle fracture.

  3. Water spray cooling technique applied on a photovoltaic panel: The performance response

    International Nuclear Information System (INIS)

    Nižetić, S.; Čoko, D.; Yadav, A.; Grubišić-Čabo, F.

    2016-01-01

    Highlights: • An experimental study was conducted on a monocrystalline photovoltaic panel (PV). • A water spray cooling technique was implemented to determine PV panel response. • The experimental results showed favorable cooling effect on the panel performance. • A feasibility aspect of the water spray cooling technique was also proven. - Abstract: This paper presents an alternative cooling technique for photovoltaic (PV) panels that includes a water spray application over panel surfaces. An alternative cooling technique in the sense that both sides of the PV panel were cooled simultaneously, to investigate the total water spray cooling effect on the PV panel performance in circumstances of peak solar irradiation levels. A specific experimental setup was elaborated in detail and the developed cooling system for the PV panel was tested in a geographical location with a typical Mediterranean climate. The experimental result shows that it is possible to achieve a maximal total increase of 16.3% (effective 7.7%) in electric power output and a total increase of 14.1% (effective 5.9%) in PV panel electrical efficiency by using the proposed cooling technique in circumstances of peak solar irradiation. Furthermore, it was also possible to decrease panel temperature from an average 54 °C (non-cooled PV panel) to 24 °C in the case of simultaneous front and backside PV panel cooling. Economic feasibility was also determined for of the proposed water spray cooling technique, where the main advantage of the analyzed cooling technique is regarding the PV panel’s surface and its self-cleaning effect, which additionally acts as a booster to the average delivered electricity.

  4. A state-of-the-art anisotropic rock deformation model incorporating the development of mobilised shear strength

    Science.gov (United States)

    Noor, M. J. Md; Jobli, A. F.

    2018-04-01

    Currently rock deformation is estimated using the relationship between the deformation modulus Em and the stress-strain curve. There have been many studies conducted to estimate the value of Em. This Em is basically derived from conducting unconfined compression test, UCS. However, the actual stress condition of the rock in the ground is anisotropic stress condition where the rock mass is subjected to different confining and vertical pressures. In addition, there is still no empirical or semi-empirical framework that has been developed for the prediction of rock stress-strain response under anisotropic stress condition. Arock triaxial machine GCTS Triaxial RTX-3000 has been deployed to obtain the anisotropic stress-strain relationship for weathered granite grade II from Rawang, Selangor sampled at depth of 20 m and subjected to confining pressure of 2 MPa, 7.5 MPa and 14 MPa. The developed mobilised shear strength envelope within the specimen of 50 mm diameter and 100 mm height during the application of the deviator stress is interpreted from the stress-strain curves. These mobilised shear strength envelopes at various axial strains are the intrinsic property and unique for the rock. Once this property has been established then it is being used to predict the stress-strain relationship at any confining pressure. The predicted stress-strain curves are compared against the curves obtained from the tests. A very close prediction is achieved to substantiate the applicability of this rock deformation model. This is a state-of-the art rock deformation theory which characterise the deformation base on the applied load and the developed mobilised shear strength within the rock body.

  5. Performance values for non destructive assay (NDA) techniques applied to safeguards: the 2002 evaluation by the ESARDA NDA Working Group

    International Nuclear Information System (INIS)

    Guardini, S.

    2003-01-01

    The first evaluation of NDA performance values undertaken by the ESARDA Working Group for Standards and Non Destructive Assay Techniques (WGNDA) was published in 1993. Almost 10 years later the Working Group decided to review those values, to report about improvements and to issue new performance values for techniques which were not applied in the early nineties, or were at that time only emerging. Non-Destructive Assay techniques have become more and more important in recent years, and they are used to a large extent in nuclear material accountancy and control both by operators and control authorities. As a consequence, the performance evaluation for NDA techniques is of particular relevance to safeguards authorities in optimising Safeguards operations and reducing costs. Performance values are important also for NMAC regulators, to define detection levels, limits for anomalies, goal quantities and to negotiate basic audit rules. This paper presents the latest evaluation of ESARDA Performance Values (EPVs) for the most common NDA techniques currently used for the assay of nuclear materials for Safeguards purposes. The main topics covered by the document are: techniques for plutonium bearing materials: PuO 2 and MOX; techniques for U-bearing materials; techniques for U and Pu in liquid form; techniques for spent fuel assay. This issue of the performance values is the result of specific international round robin exercises, field measurements and ad hoc experiments, evaluated and discussed in the ESARDA NDA Working Group. (author)

  6. Synchrotron and Simulations Techniques Applied to Problems in Materials Science: Catalysts and Azul Maya Pigments

    International Nuclear Information System (INIS)

    Chianelli, R.

    2005-01-01

    Development of synchrotron techniques for the determination of the structure of disordered, amorphous and surface materials has exploded over the past twenty years due to the increasing availability of high flux synchrotron radiation and the continuing development of increasingly powerful synchrotron techniques. These techniques are available to materials scientists who are not necessarily synchrotron scientists through interaction with effective user communities that exist at synchrotrons such as the Stanford Synchrotron Radiation Laboratory (SSRL). In this article we review the application of multiple synchrotron characterization techniques to two classes of materials defined as ''surface compounds.'' One class of surface compounds are materials like MoS 2-x C x that are widely used petroleum catalysts used to improve the environmental properties of transportation fuels. These compounds may be viewed as ''sulfide supported carbides'' in their catalytically active states. The second class of ''surface compounds'' is the ''Maya Blue'' pigments that are based on technology created by the ancient Maya. These compounds are organic/inorganic ''surface complexes'' consisting of the dye indigo and palygorskite, a common clay. The identification of both surface compounds relies on the application of synchrotron techniques as described in this report

  7. Statistical learning techniques applied to epidemiology: a simulated case-control comparison study with logistic regression

    Directory of Open Access Journals (Sweden)

    Land Walker H

    2011-01-01

    Full Text Available Abstract Background When investigating covariate interactions and group associations with standard regression analyses, the relationship between the response variable and exposure may be difficult to characterize. When the relationship is nonlinear, linear modeling techniques do not capture the nonlinear information content. Statistical learning (SL techniques with kernels are capable of addressing nonlinear problems without making parametric assumptions. However, these techniques do not produce findings relevant for epidemiologic interpretations. A simulated case-control study was used to contrast the information embedding characteristics and separation boundaries produced by a specific SL technique with logistic regression (LR modeling representing a parametric approach. The SL technique was comprised of a kernel mapping in combination with a perceptron neural network. Because the LR model has an important epidemiologic interpretation, the SL method was modified to produce the analogous interpretation and generate odds ratios for comparison. Results The SL approach is capable of generating odds ratios for main effects and risk factor interactions that better capture nonlinear relationships between exposure variables and outcome in comparison with LR. Conclusions The integration of SL methods in epidemiology may improve both the understanding and interpretation of complex exposure/disease relationships.

  8. Schlieren technique applied to the arc temperature measurement in a high energy density cutting torch

    International Nuclear Information System (INIS)

    Prevosto, L.; Mancinelli, B.; Artana, G.; Kelly, H.

    2010-01-01

    Plasma temperature and radial density profiles of the plasma species in a high energy density cutting arc have been obtained by using a quantitative schlieren technique. A Z-type two-mirror schlieren system was used in this research. Due to its great sensibility such technique allows measuring plasma composition and temperature from the arc axis to the surrounding medium by processing the gray-level contrast values of digital schlieren images recorded at the observation plane for a given position of a transverse knife located at the exit focal plane of the system. The technique has provided a good visualization of the plasma flow emerging from the nozzle and its interactions with the surrounding medium and the anode. The obtained temperature values are in good agreement with those values previously obtained by the authors on the same torch using Langmuir probes.

  9. Applied techniques for high bandwidth data transfers across wide area networks

    International Nuclear Information System (INIS)

    Lee, Jason; Gunter, Dan; Tierney, Brian; Allcock, Bill; Bester, Joe; Bresnahan, John; Tuecke, Steve

    2001-01-01

    Large distributed systems such as Computational/Data Grids require large amounts of data to be co-located with the computing facilities for processing. Ensuring that the data is there in time for the computation in today's Internet is a massive problem. From our work developing a scalable distributed network cache, we have gained experience with techniques necessary to achieve high data throughput over high bandwidth Wide Area Networks (WAN). In this paper, we discuss several hardware and software design techniques and issues, and then describe their application to an implementation of an enhanced FTP protocol called GridFTP. We also describe results from two applications using these techniques, which were obtained at the Supercomputing 2000 conference

  10. Applied predictive analytics principles and techniques for the professional data analyst

    CERN Document Server

    Abbott, Dean

    2014-01-01

    Learn the art and science of predictive analytics - techniques that get results Predictive analytics is what translates big data into meaningful, usable business information. Written by a leading expert in the field, this guide examines the science of the underlying algorithms as well as the principles and best practices that govern the art of predictive analytics. It clearly explains the theory behind predictive analytics, teaches the methods, principles, and techniques for conducting predictive analytics projects, and offers tips and tricks that are essential for successful predictive mode

  11. Applied techniques for high bandwidth data transfers across wide area networks

    International Nuclear Information System (INIS)

    Lee, J.; Gunter, D.; Tierney, B.; Allcock, B.; Bester, J.; Bresnahan, J.; Tuecke, S.

    2001-01-01

    Large distributed systems such as Computational/Data Grids require large amounts of data to be co-located with the computing facilities for processing. From their work developing a scalable distributed network cache, the authors have gained experience with techniques necessary to achieve high data throughput over high bandwidth Wide Area Networks (WAN). The authors discuss several hardware and software design techniques, and then describe their application to an implementation of an enhanced FTP protocol called GridFTP. The authors describe results from the Supercomputing 2000 conference

  12. People Recognition for Loja ECU911 applying artificial vision techniques

    Directory of Open Access Journals (Sweden)

    Diego Cale

    2016-05-01

    Full Text Available This article presents a technological proposal based on artificial vision which aims to search people in an intelligent way by using IP video cameras. Currently, manual searching process is time and resource demanding in contrast to automated searching one, which means that it could be replaced. In order to obtain optimal results, three different techniques of artificial vision were analyzed (Eigenfaces, Fisherfaces, Local Binary Patterns Histograms. The selection process considered factors like lighting changes, image quality and changes in the angle of focus of the camera. Besides, a literature review was conducted to evaluate several points of view regarding artificial vision techniques.

  13. U P1, an example for advanced techniques applied to high level activity dismantling

    International Nuclear Information System (INIS)

    Michel-Noel, M.; Calixte, O.; Blanchard, S.; Bani, J.; Girones, P.; Moitrier, C.; Terry, G.; Bourdy, R.

    2014-01-01

    The U P1 plant on the CEA Marcoule site was dedicated to the processing of spend fuels from the G1, G2 and G3 plutonium-producing reactors. This plant represents 20.000 m 2 of workshops housing about 1000 hot cells. In 1998, a huge program for the dismantling and cleaning-up of the UP1 plant was launched. CEA has developed new techniques to face the complexity of the dismantling operations. These techniques include immersive virtual reality, laser cutting, a specific manipulator arm called MAESTRO and remote handling. (A.C.)

  14. Effect of the reinforcement bar arrangement on the efficiency of electrochemical chloride removal technique applied to reinforced concrete structures

    International Nuclear Information System (INIS)

    Garces, P.; Sanchez de Rojas, M.J.; Climent, M.A.

    2006-01-01

    This paper reports on the research done to find out the effect that different bar arrangements may have on the efficiency of the electrochemical chloride removal (ECR) technique when applied to a reinforced concrete structural member. Five different types of bar arrangements were considered, corresponding to typical structural members such as columns (with single and double bar reinforcing), slabs, beams and footings. ECR was applied in several steps. We observe that the extraction efficiency depends on the reinforcing bar arrangement. A uniform layer set-up favours chloride extraction. Electrochemical techniques were also used to estimate the reinforcing bar corrosion states, as well as measure the corrosion potential, and instant corrosion rate based on the polarization resistance technique. After ECR treatment, a reduction in the corrosion levels is observed falling short of the depassivation threshold

  15. Validation and qualification of surface-applied fibre optic strain sensors using application-independent optical techniques

    International Nuclear Information System (INIS)

    Schukar, Vivien G; Kadoke, Daniel; Kusche, Nadine; Münzenberger, Sven; Gründer, Klaus-Peter; Habel, Wolfgang R

    2012-01-01

    Surface-applied fibre optic strain sensors were investigated using a unique validation facility equipped with application-independent optical reference systems. First, different adhesives for the sensor's application were analysed regarding their material properties. Measurements resulting from conventional measurement techniques, such as thermo-mechanical analysis and dynamic mechanical analysis, were compared with measurements resulting from digital image correlation, which has the advantage of being a non-contact technique. Second, fibre optic strain sensors were applied to test specimens with the selected adhesives. Their strain-transfer mechanism was analysed in comparison with conventional strain gauges. Relative movements between the applied sensor and the test specimen were visualized easily using optical reference methods, digital image correlation and electronic speckle pattern interferometry. Conventional strain gauges showed limited opportunities for an objective strain-transfer analysis because they are also affected by application conditions. (paper)

  16. Comparative assessment of PIV-based pressure evaluation techniques applied to a transonic base flow

    NARCIS (Netherlands)

    Blinde, P; Michaelis, D; van Oudheusden, B.W.; Weiss, P.E.; de Kat, R.; Laskari, A.; Jeon, Y.J.; David, L; Schanz, D; Huhn, F.; Gesemann, S; Novara, M.; McPhaden, C.; Neeteson, N.; Rival, D.; Schneiders, J.F.G.; Schrijer, F.F.J.

    2016-01-01

    A test case for PIV-based pressure evaluation techniques has been developed by constructing a simulated experiment from a ZDES simulation for an axisymmetric base flow at Mach 0.7. The test case comprises sequences of four subsequent particle images (representing multi-pulse data) as well as

  17. Practising What We Teach: Vocational Teachers Learn to Research through Applying Action Learning Techniques

    Science.gov (United States)

    Lasky, Barbara; Tempone, Irene

    2004-01-01

    Action learning techniques are well suited to the teaching of organisation behaviour students because of their flexibility, inclusiveness, openness, and respect for individuals. They are no less useful as a tool for change for vocational teachers, learning, of necessity, to become researchers. Whereas traditional universities have always had a…

  18. Nuclear and conventional techniques applied to the analysis of Purhepecha metals of the Pareyon collection

    International Nuclear Information System (INIS)

    Mendez, U.; Tenorio C, D.; Ruvalcaba, J.L.; Lopez, J.A.

    2005-01-01

    The main objective of this investigation was to determine the composition and microstructure of 13 metallic devices by means of the nuclear techniques of PIXE, RBS and conventional; which were elaborated starting from copper and gold, and they were in the offering of a tarasc personage located in the 'Matamoros' porch in Uruapan, Michoacan, Mexico. (Author)

  19. Urban field guide: applying social forestry observation techniques to the east coast megalopolis

    Science.gov (United States)

    E. Svendsen; V. Marshall; M.F. Ufer

    2006-01-01

    A changing economy and different lifestyles have altered the meaning of the forest in the northeastern United States, prompting scientists to reconsider the spatial form, stewardship and function of the urban forest. The Authors describe how social observation techniques and the employment of a novel, locally based, participatory hand-held monitoring system could aid...

  20. Space-mapping techniques applied to the optimization of a safety isolating transformer

    NARCIS (Netherlands)

    T.V. Tran; S. Brisset; D. Echeverria (David); D.J.P. Lahaye (Domenico); P. Brochet

    2007-01-01

    textabstractSpace-mapping optimization techniques allow to allign low-fidelity and high-fidelity models in order to reduce the computational time and increase the accuracy of the solution. The main idea is to build an approximate model from the difference of response between both models. Therefore

  1. MSC/NASTRAN ''expert'' techniques developed and applied to the TFTR poloidal field coils

    International Nuclear Information System (INIS)

    O'Toole, J.A.

    1986-01-01

    The TFTR poloidal field (PF) coils are being analyzed by PPPL and Grumman using MSC/NASTRAN as a part of an overall effort to establish the absolute limiting conditions of operation for TFTR. Each of the PF coils will be analyzed in depth, using a detailed set of finite element models. Several of the models developed are quite large because each copper turn, as well as its surrounding insulation, was modeled using solid elements. Several of the finite element models proved large enough to tax the capabilities of the National Magnetic Fusion Energy Computer Center (NMFECC), specifically disk storage space. To allow the use of substructuring techniques with their associated data bases for the larger models, it became necessary to employ certain infrequently used MSC/NASTRAN ''expert'' techniques. The techniques developed used multiple data bases and data base sets to divide each problem into a series of computer runs. For each run, only the data required was kept on active disk space, the remainder being placed in inactive ''FILEM'' storage, thus, minimizing active disk space required at any time and permitting problem solution using the NMFECC. A representative problem using the TFTR OH-1 coil global model provides an example of the techniques developed. The special considerations necessary to obtain proper results are discussed

  2. Spectral deformation techniques applied to the study of quantum statistical irreversible processes

    International Nuclear Information System (INIS)

    Courbage, M.

    1978-01-01

    A procedure of analytic continuation of the resolvent of Liouville operators for quantum statistical systems is discussed. When applied to the theory of irreversible processes of the Brussels School, this method supports the idea that the restriction to a class of initial conditions is necessary to obtain an irreversible behaviour. The general results are tested on the Friedrichs model. (Auth.)

  3. Do trained practice nurses apply motivational interviewing techniques in primary care consultations?

    NARCIS (Netherlands)

    Noordman, J.; Lee, I. van der; Nielen, M.; Vlek, H.; Weijden, T. van der; Dulmen, S. van

    2012-01-01

    Background: Reducing the prevalence of unhealthy lifestyle behaviour could positively influence health. Motivational interviewing (MI) is used to promote change in unhealthy lifestyle behaviour as part of primary or secondary prevention. Whether MI is actually applied as taught is unknown. Practice

  4. New enhanced sensitivity infrared laser spectroscopy techniques applied to reactive plasmas and trace gas detection

    NARCIS (Netherlands)

    Welzel, S.

    2009-01-01

    Infrared laser absorption spectroscopy (IRLAS) employing both tuneable diode and quantum cascade lasers (TDLs, QCLs) has been applied with both high sensitivity and high time resolution to plasma diagnostics and trace gas measurements. TDLAS combined with a conventional White type multiple pass cell

  5. Applied Statistics: From Bivariate through Multivariate Techniques [with CD-ROM

    Science.gov (United States)

    Warner, Rebecca M.

    2007-01-01

    This book provides a clear introduction to widely used topics in bivariate and multivariate statistics, including multiple regression, discriminant analysis, MANOVA, factor analysis, and binary logistic regression. The approach is applied and does not require formal mathematics; equations are accompanied by verbal explanations. Students are asked…

  6. Parameters and definitions in applied technique quality test for nuclear magnetic resonance imaging system (NMRI)

    International Nuclear Information System (INIS)

    Lin Zhikai; Zhao Lancai

    1999-08-01

    During the past two decades, medical diagnostic imaging technique has achieved dramatic development such as CT, MRI, PET, DSA and so on. The most striking examples of them are the application of X ray computerized tomography (CT) and magnetic resonance imaging in the field of medical diagnosis. It can be predicted that magnetic resonance imaging (MRI) will definitely have more widespread prospects of applications and play more and more important role in clinical diagnosis looking forward to the development of image diagnostic technique for 21 st century. The authors also present the measuring methods for some parameters. The parameters described can be used for reference by clinical diagnosticians, operators on MRI and medical physicists who engages in image quality assurance (QA) and control (QC) in performing MRI acceptance test and routine test

  7. Applying machine learning techniques for forecasting flexibility of virtual power plants

    DEFF Research Database (Denmark)

    MacDougall, Pamela; Kosek, Anna Magdalena; Bindner, Henrik W.

    2016-01-01

    network as well as the multi-variant linear regression. It is found that it is possible to estimate the longevity of flexibility with machine learning. The linear regression algorithm is, on average, able to estimate the longevity with a 15% error. However, there was a significant improvement with the ANN...... approach to investigating the longevity of aggregated response of a virtual power plant using historic bidding and aggregated behaviour with machine learning techniques. The two supervised machine learning techniques investigated and compared in this paper are, multivariate linear regression and single...... algorithm achieving, on average, a 5.3% error. This is lowered 2.4% when learning for the same virtual power plant. With this information it would be possible to accurately offer residential VPP flexibility for market operations to safely avoid causing further imbalances and financial penalties....

  8. Geologic-radiometric techniques applied for uranium prospection at the Hierro-Cayo Largo area

    International Nuclear Information System (INIS)

    Gongora, L.E.; Olivera, J.

    1995-01-01

    Using geologic-radiometric techniques uraniferous anomalies were evaluated at the Hierro-Cayo Largo area located in Pinar del Rio province. During the uranium prospection works at most promising areas, geologic itineraries and gamma ray, radon emanation spectrometric survey were done. Trenches were made and some boreholes were drilled (up to 20-30 m depth). In addition a lot of samples were taken in order to determine the amount of U, Ra, Th, y K by spectrometric techniques. As result of this investigation, a geological placing, a mineralogical and geochemical characteristic of uraniferous mineralization was possible to find out. The appropriate prospection indications for uranium exploration at Esperanza geologic zone were defined

  9. Magnetic Resonance Techniques Applied to the Diagnosis and Treatment of Parkinson’s Disease

    Science.gov (United States)

    de Celis Alonso, Benito; Hidalgo-Tobón, Silvia S.; Menéndez-González, Manuel; Salas-Pacheco, José; Arias-Carrión, Oscar

    2015-01-01

    Parkinson’s disease (PD) affects at least 10 million people worldwide. It is a neurodegenerative disease, which is currently diagnosed by neurological examination. No neuroimaging investigation or blood biomarker is available to aid diagnosis and prognosis. Most effort toward diagnosis using magnetic resonance (MR) has been focused on the use of structural/anatomical neuroimaging and diffusion tensor imaging (DTI). However, deep brain stimulation, a current strategy for treating PD, is guided by MR imaging (MRI). For clinical prognosis, diagnosis, and follow-up investigations, blood oxygen level-dependent MRI, DTI, spectroscopy, and transcranial magnetic stimulation have been used. These techniques represent the state of the art in the last 5 years. Here, we focus on MR techniques for the diagnosis and treatment of Parkinson’s disease. PMID:26191037

  10. The Ecological Profiles Technique applied to data from Lichtenburg, South Africa

    Directory of Open Access Journals (Sweden)

    J. W. Morris

    1974-12-01

    Full Text Available The method of ecological profiles and information shared between species and ecological variables, developed in France, is described for the first time in English. Preliminary results, using the technique on Bankenveld quadrat data from Lichtenburg, Western Transvaal, are given. It is concluded that the method has great potential value for the understanding of the autecology of South African species provided that the sampling method is appropriate.

  11. Computer vision techniques applied to the quality control of ceramic plates

    OpenAIRE

    Silveira, Joaquim; Ferreira, Manuel João Oliveira; Santos, Cristina; Martins, Teresa

    2009-01-01

    This paper presents a system, based on computer vision techniques, that detects and quantifies different types of defects in ceramic plates. It was developed in collaboration with the industrial ceramic sector and consequently it was focused on the defects that are considered more quality depreciating by the Portuguese industry. They are of three main types: cracks; granules and relief surface. For each type the development was specific as far as image processing techn...

  12. Applying Multi-Criteria Decision-Making Techniques to Prioritize Agility Drivers

    OpenAIRE

    Ahmad Jafarnejad; Sayyed Mohammad Reza Davoodi; Abolfazl Sherafat

    2013-01-01

    It seems that to recognize and classify the factors affecting organizational agility and need to specify the amount of their importance for the organization is essential to preserve survival and success in today's environment. This paper reviews the concept of agility and its division in the following indicators included the factors of motivations organizational agility that have been ranked in terms of level of importance and their influence by the techniques of MCDM. The inner complexity, s...

  13. Artificial intelligence techniques applied to hourly global irradiance estimation from satellite-derived cloud index

    Energy Technology Data Exchange (ETDEWEB)

    Zarzalejo, L.F.; Ramirez, L.; Polo, J. [DER-CIEMAT, Madrid (Spain). Renewable Energy Dept.

    2005-07-01

    Artificial intelligence techniques, such as fuzzy logic and neural networks, have been used for estimating hourly global radiation from satellite images. The models have been fitted to measured global irradiance data from 15 Spanish terrestrial stations. Both satellite imaging data and terrestrial information from the years 1994, 1995 and 1996 were used. The results of these artificial intelligence models were compared to a multivariate regression based upon Heliosat I model. A general better behaviour was observed for the artificial intelligence models. (author)

  14. 3D-Laser-Scanning Technique Applied to Bulk Density Measurements of Apollo Lunar Samples

    Science.gov (United States)

    Macke, R. J.; Kent, J. J.; Kiefer, W. S.; Britt, D. T.

    2015-01-01

    In order to better interpret gravimetric data from orbiters such as GRAIL and LRO to understand the subsurface composition and structure of the lunar crust, it is import to have a reliable database of the density and porosity of lunar materials. To this end, we have been surveying these physical properties in both lunar meteorites and Apollo lunar samples. To measure porosity, both grain density and bulk density are required. For bulk density, our group has historically utilized sub-mm bead immersion techniques extensively, though several factors have made this technique problematic for our work with Apollo samples. Samples allocated for measurement are often smaller than optimal for the technique, leading to large error bars. Also, for some samples we were required to use pure alumina beads instead of our usual glass beads. The alumina beads were subject to undesirable static effects, producing unreliable results. Other investigators have tested the use of 3d laser scanners on meteorites for measuring bulk volumes. Early work, though promising, was plagued with difficulties including poor response on dark or reflective surfaces, difficulty reproducing sharp edges, and large processing time for producing shape models. Due to progress in technology, however, laser scanners have improved considerably in recent years. We tested this technique on 27 lunar samples in the Apollo collection using a scanner at NASA Johnson Space Center. We found it to be reliable and more precise than beads, with the added benefit that it involves no direct contact with the sample, enabling the study of particularly friable samples for which bead immersion is not possible

  15. Artificial intelligence techniques applied to hourly global irradiance estimation from satellite-derived cloud index

    International Nuclear Information System (INIS)

    Zarzalejo, Luis F.; Ramirez, Lourdes; Polo, Jesus

    2005-01-01

    Artificial intelligence techniques, such as fuzzy logic and neural networks, have been used for estimating hourly global radiation from satellite images. The models have been fitted to measured global irradiance data from 15 Spanish terrestrial stations. Both satellite imaging data and terrestrial information from the years 1994, 1995 and 1996 were used. The results of these artificial intelligence models were compared to a multivariate regression based upon Heliosat I model. A general better behaviour was observed for the artificial intelligence models

  16. Applying the sterile insect technique to the control of insect pests

    International Nuclear Information System (INIS)

    LaChance, L.E.; Klassen, W.

    1991-01-01

    The sterile insect technique involves the mass-rearing of insects, which are sterilized by gamma rays from a 60 Co source before being released in a controlled fashion into nature. Matings between the sterile insects released and native insects produce no progeny, and so if enough of these matings occur the pest population can be controlled or even eradicated. A modification of the technique, especially suitable for the suppression of the moths and butterflies, is called the F, or inherited sterility method. In this, lower radiation doses are used such that the released males are only partially sterile (30-60%) and the females are fully sterile. When released males mate with native females some progeny are produced, but they are completely sterile. Thus, full expression of the sterility is delayed by one generation. This article describes the use of the sterile insect technique in controlling the screwworm fly, the tsetse fly, the medfly, the pink bollworm and the melon fly, and of the F 1 sterility method in the eradication of local gypsy moth infestations. 18 refs, 5 figs, 1 tab

  17. Acoustic Emission and Echo Signal Compensation Techniques Applied to an Ultrasonic Logging-While-Drilling Caliper.

    Science.gov (United States)

    Yao, Yongchao; Ju, Xiaodong; Lu, Junqiang; Men, Baiyong

    2017-06-10

    A logging-while-drilling (LWD) caliper is a tool used for the real-time measurement of a borehole diameter in oil drilling engineering. This study introduces the mechanical structure and working principle of a new LWD caliper based on ultrasonic distance measurement (UDM). The detection range is a major performance index of a UDM system. This index is determined by the blind zone length and remote reflecting interface detection capability of the system. To reduce the blind zone length and detect near the reflecting interface, a full bridge acoustic emission technique based on bootstrap gate driver (BGD) and metal-oxide-semiconductor field effect transistor (MOSFET) is designed by analyzing the working principle and impedance characteristics of a given piezoelectric transducer. To detect the remote reflecting interface and reduce the dynamic range of the received echo signals, the relationships between the echo amplitude and propagation distance of ultrasonic waves are determined. A signal compensation technique based on time-varying amplification theory, which can automatically change the gain according to the echo arrival time is designed. Lastly, the aforementioned techniques and corresponding circuits are experimentally verified. Results show that the blind zone length in the UDM system of the LWD caliper is significantly reduced and the capability to detect the remote reflecting interface is considerably improved.

  18. Acoustic Emission and Echo Signal Compensation Techniques Applied to an Ultrasonic Logging-While-Drilling Caliper

    Directory of Open Access Journals (Sweden)

    Yongchao Yao

    2017-06-01

    Full Text Available A logging-while-drilling (LWD caliper is a tool used for the real-time measurement of a borehole diameter in oil drilling engineering. This study introduces the mechanical structure and working principle of a new LWD caliper based on ultrasonic distance measurement (UDM. The detection range is a major performance index of a UDM system. This index is determined by the blind zone length and remote reflecting interface detection capability of the system. To reduce the blind zone length and detect near the reflecting interface, a full bridge acoustic emission technique based on bootstrap gate driver (BGD and metal-oxide-semiconductor field effect transistor (MOSFET is designed by analyzing the working principle and impedance characteristics of a given piezoelectric transducer. To detect the remote reflecting interface and reduce the dynamic range of the received echo signals, the relationships between the echo amplitude and propagation distance of ultrasonic waves are determined. A signal compensation technique based on time-varying amplification theory, which can automatically change the gain according to the echo arrival time is designed. Lastly, the aforementioned techniques and corresponding circuits are experimentally verified. Results show that the blind zone length in the UDM system of the LWD caliper is significantly reduced and the capability to detect the remote reflecting interface is considerably improved.

  19. Applied nuclear γ-resonance as fingerprint technique in geochemistry and mineralogy

    International Nuclear Information System (INIS)

    Constantinescu, S.

    2003-01-01

    The aim of the present paper is to evidence the new developments of one of the most refined technique, the nuclear γ resonance or the well-known Moessbauer effect, in the field of mineralogical and geo-chemical investigation. There are many Moessbauer studies on minerals, but the development, the new performance of the Moessbauer equipment and of the computers impose to review more profoundly and more thoroughly the information, which this non-destructive technique offers. This task became more and more pressingly because a lot of minerals contain in high proportion, the Moessbauer isotopes. Generally, the mineralogists, physicists and chemists hope to obtain more refined and complete information about the physics and chemistry synthesis aspects in solid state transformation of some natural and synthetic materials and also about the structural aspects, by these kind of techniques. On this line, the authors very shortly review the principal aspects of the Moessbauer spectroscopy and underline the most important information one can obtain from spectra. The recent results, which have been obtained on minerals extracted from Romanian geological deposits by the authors, will be discussed in detail in the second part of this article. (authors)

  20. An efficient permeability scaling-up technique applied to the discretized flow equations

    Energy Technology Data Exchange (ETDEWEB)

    Urgelli, D.; Ding, Yu [Institut Francais du Petrole, Rueil Malmaison (France)

    1997-08-01

    Grid-block permeability scaling-up for numerical reservoir simulations has been discussed for a long time in the literature. It is now recognized that a full permeability tensor is needed to get an accurate reservoir description at large scale. However, two major difficulties are encountered: (1) grid-block permeability cannot be properly defined because it depends on boundary conditions; (2) discretization of flow equations with a full permeability tensor is not straightforward and little work has been done on this subject. In this paper, we propose a new method, which allows us to get around both difficulties. As the two major problems are closely related, a global approach will preserve the accuracy. So, in the proposed method, the permeability up-scaling technique is integrated in the discretized numerical scheme for flow simulation. The permeability is scaled-up via the transmissibility term, in accordance with the fluid flow calculation in the numerical scheme. A finite-volume scheme is particularly studied, and the transmissibility scaling-up technique for this scheme is presented. Some numerical examples are tested for flow simulation. This new method is compared with some published numerical schemes for full permeability tensor discretization where the full permeability tensor is scaled-up through various techniques. Comparing the results with fine grid simulations shows that the new method is more accurate and more efficient.

  1. Metal oxide collectors for storing matter technique applied in secondary ion mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Miśnik, Maciej [Institute of Tele and Radio Technology, ul. Ratuszowa 11, 03-450 Warszawa (Poland); Gdańsk University of Technology (Poland); Konarski, Piotr [Institute of Tele and Radio Technology, ul. Ratuszowa 11, 03-450 Warszawa (Poland); Zawada, Aleksander [Institute of Tele and Radio Technology, ul. Ratuszowa 11, 03-450 Warszawa (Poland); Military University of Technology, Warszawa (Poland)

    2016-03-15

    We present results of the use of metal and metal oxide substrates that serve as collectors in ‘storing matter’, the quantitative technique of secondary ion mass spectrometry (SIMS). This technique allows separating the two base processes of secondary ion formation in SIMS. Namely, the process of ion sputtering is separated from the process of ionisation. The technique allows sputtering of the analysed sample and storing the sputtered material, with sub-monolayer coverage, onto a collector surface. Such deposits can be then analysed by SIMS, and as a result, the so called ‘matrix effects’ are significantly reduced. We perform deposition of the sputtered material onto Ti and Cu substrates and also onto metal oxide substrates as molybdenum, titanium, tin and indium oxides. The process of sputtering is carried within the same vacuum chamber where the SIMS analysis of the collected material is performed. For sputtering and SIMS analysis of the deposited material we use 5 keV Ar{sup +} beam of 500 nA. The presented results are obtained with the use of stationary collectors. Here we present a case study of chromium. The obtained results show that the molybdenum and titanium oxide substrates used as collectors increase useful yield by two orders, with respect to such pure elemental collectors as Cu and Ti. Here we define useful yield as a ratio of the number of detected secondary ions during SIMS analysis and the number of atoms sputtered during the deposition process.

  2. Domain Immersion Technique And Free Surface Computations Applied To Extrusion And Mixing Processes

    Science.gov (United States)

    Valette, Rudy; Vergnes, Bruno; Basset, Olivier; Coupez, Thierry

    2007-04-01

    This work focuses on the development of numerical techniques devoted to the simulation of mixing processes of complex fluids such as twin-screw extrusion or batch mixing. In mixing process simulation, the absence of symmetry of the moving boundaries (the screws or the rotors) implies that their rigid body motion has to be taken into account by using a special treatment. We therefore use a mesh immersion technique (MIT), which consists in using a P1+/P1-based (MINI-element) mixed finite element method for solving the velocity-pressure problem and then solving the problem in the whole barrel cavity by imposing a rigid motion (rotation) to nodes found located inside the so called immersed domain, each subdomain (screw, rotor) being represented by a surface CAD mesh (or its mathematical equation in simple cases). The independent meshes are immersed into a unique backgound computational mesh by computing the distance function to their boundaries. Intersections of meshes are accounted for, allowing to compute a fill factor usable as for the VOF methodology. This technique, combined with the use of parallel computing, allows to compute the time-dependent flow of generalized Newtonian fluids including yield stress fluids in a complex system such as a twin screw extruder, including moving free surfaces, which are treated by a "level set" and Hamilton-Jacobi method.

  3. Applying Data-mining techniques to study drought periods in Spain

    Science.gov (United States)

    Belda, F.; Penades, M. C.

    2010-09-01

    Data-mining is a technique that it can be used to interact with large databases and to help in the discovery relations between parameters by extracting information from massive and multiple data archives. Drought affects many economic and social sectors, from agricultural to transportation, going through urban water deficit and the development of modern industries. With these problems and drought geographical and temporal distribution it's difficult to find a single definition of drought. Improving the understanding of the knowledge of climatic index is necessary to reduce the impacts of drought and to facilitate quick decisions regarding this problem. The main objective is to analyze drought periods from 1950 to 2009 in Spain. We use several kinds of information, different formats, sources and transmission mode. We use satellite-based Vegetation Index, dryness index for several temporal periods. We use daily and monthly precipitation and temperature data and soil moisture data from numerical weather model. We calculate mainly Standardized Precipitation Index (SPI) that it has been used amply in the bibliography. We use OLAP-Mining techniques to discovery of association rules between remote-sensing, numerical weather model and climatic index. Time series Data- Mining techniques organize data as a sequence of events, with each event having a time of recurrence, to cluster the data into groups of records or cluster with similar characteristics. Prior climatological classification is necessary if we want to study drought periods over all Spain.

  4. Air flow measurement techniques applied to noise reduction of a centrifugal blower

    Science.gov (United States)

    Laage, John W.; Armstrong, Ashli J.; Eilers, Daniel J.; Olsen, Michael G.; Mann, J. Adin

    2005-09-01

    The air flow in a centrifugal blower was studied using a variety of flow and sound measurement techniques. The flow measurement techniques employed included Particle Image Velocimetry (PIV), pitot tubes, and a five hole spherical probe. PIV was used to measure instantaneous and ensemble-averaged velocity fields over large area of the outlet duct as a function of fan position, allowing for the visualization of the flow as it leave the fan blades and progressed downstream. The results from the flow measurements were reviewed along side the results of the sound measurements with the goal of identifying sources of noise and inefficiencies in flow performance. The radiated sound power was divided into broadband and tone noise and measures of the flow. The changes in the tone and broadband sound were compared to changes in flow quantities such as the turbulent kinetic energy and Reynolds stress. Results for each method will be presented to demonstrate the strengths of each flow measurement technique as well as their limitations. Finally, the role that each played in identifying noise sources is described.

  5. A photoacoustic technique applied to detection of ethylene emissions in edible coated passion fruit

    International Nuclear Information System (INIS)

    Alves, G V L; Santos, W C dos; Vargas, H; Silva, M G da; Waldman, W R; Oliveira, J G

    2010-01-01

    Photoacoustic spectroscopy was applied to study the physiological behavior of passion fruit when coated with edible films. The results have shown a reduction of the ethylene emission rate. Weight loss monitoring has not shown any significant differences between the coated and uncoated passion fruit. On the other hand, slower color changes of coated samples suggest a slowdown of the ripening process in coated passion fruit.

  6. Hybrid multicore/vectorisation technique applied to the elastic wave equation on a staggered grid

    Science.gov (United States)

    Titarenko, Sofya; Hildyard, Mark

    2017-07-01

    In modern physics it has become common to find the solution of a problem by solving numerically a set of PDEs. Whether solving them on a finite difference grid or by a finite element approach, the main calculations are often applied to a stencil structure. In the last decade it has become usual to work with so called big data problems where calculations are very heavy and accelerators and modern architectures are widely used. Although CPU and GPU clusters are often used to solve such problems, parallelisation of any calculation ideally starts from a single processor optimisation. Unfortunately, it is impossible to vectorise a stencil structured loop with high level instructions. In this paper we suggest a new approach to rearranging the data structure which makes it possible to apply high level vectorisation instructions to a stencil loop and which results in significant acceleration. The suggested method allows further acceleration if shared memory APIs are used. We show the effectiveness of the method by applying it to an elastic wave propagation problem on a finite difference grid. We have chosen Intel architecture for the test problem and OpenMP (Open Multi-Processing) since they are extensively used in many applications.

  7. Assessment of ground-based monitoring techniques applied to landslide investigations

    Science.gov (United States)

    Uhlemann, S.; Smith, A.; Chambers, J.; Dixon, N.; Dijkstra, T.; Haslam, E.; Meldrum, P.; Merritt, A.; Gunn, D.; Mackay, J.

    2016-01-01

    A landslide complex in the Whitby Mudstone Formation at Hollin Hill, North Yorkshire, UK is periodically re-activated in response to rainfall-induced pore-water pressure fluctuations. This paper compares long-term measurements (i.e., 2009-2014) obtained from a combination of monitoring techniques that have been employed together for the first time on an active landslide. The results highlight the relative performance of the different techniques, and can provide guidance for researchers and practitioners for selecting and installing appropriate monitoring techniques to assess unstable slopes. Particular attention is given to the spatial and temporal resolutions offered by the different approaches that include: Real Time Kinematic-GPS (RTK-GPS) monitoring of a ground surface marker array, conventional inclinometers, Shape Acceleration Arrays (SAA), tilt meters, active waveguides with Acoustic Emission (AE) monitoring, and piezometers. High spatial resolution information has allowed locating areas of stability and instability across a large slope. This has enabled identification of areas where further monitoring efforts should be focused. High temporal resolution information allowed the capture of 'S'-shaped slope displacement-time behaviour (i.e. phases of slope acceleration, deceleration and stability) in response to elevations in pore-water pressures. This study shows that a well-balanced suite of monitoring techniques that provides high temporal and spatial resolutions on both measurement and slope scale is necessary to fully understand failure and movement mechanisms of slopes. In the case of the Hollin Hill landslide it enabled detailed interpretation of the geomorphological processes governing landslide activity. It highlights the benefit of regularly surveying a network of GPS markers to determine areas for installation of movement monitoring techniques that offer higher resolution both temporally and spatially. The small sensitivity of tilt meter measurements

  8. Agent principal de rayonnement et de mobilisation stratégiques (h/f ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Dans ce contexte, l'agent principal de rayonnement et de mobilisation stratégiques élabore des démarches qui permettent de mobiliser les chercheurs et les principaux utilisateurs de la recherche dans les régions visées, afin de faire en sorte qu'ils aient l'occasion de participer à la définition des besoins de recherche dans ...

  9. Social Entrepreneurship and Mobilisation of Social Capital in European Social Enterprise - (Korean translation)

    DEFF Research Database (Denmark)

    Hulgård, Lars; Spear, Roger

    2011-01-01

    Korean translation of ”Social Entrepreneurship and Mobilisation of Social Capital in European Social Enterprise”, with Roger Spear. In Marthe Nyssens (ed.) Social Enterprises: between Market, Public Policies and Community. London: Routledge.......Korean translation of ”Social Entrepreneurship and Mobilisation of Social Capital in European Social Enterprise”, with Roger Spear. In Marthe Nyssens (ed.) Social Enterprises: between Market, Public Policies and Community. London: Routledge....

  10. Overseas Voter Mobilisation in Singapore: Implications from Malaysia’s 13th General Election

    OpenAIRE

    James Gomez; Rusdi Omar

    2013-01-01

    "This paper discusses voter mobilisation and other election-related activities of Malaysian voters living, studying and working in Singapore in the context of Malaysia's 13th general election (GE13). According to the World Bank, nearly 400,000 Malaysians reside in the city-state. Thus these figures represent a significant Malaysian voter pool based in Singapore. Efforts to mobilise these voters for general elections or other causes have political implications for both countries, which became ...

  11. Prediction of phosphorus mobilisation in inundated floodplain soils

    International Nuclear Information System (INIS)

    Loeb, Roos; Lamers, Leon P.M.; Roelofs, Jan G.M.

    2008-01-01

    After flooding, iron reduction in riverine wetlands may cause the release of large quantities of phosphorus. As phosphorus is an important nutrient causing eutrophication in aquatic systems, it is important to have a tool to predict this potential release. In this study we examined the P release to the soil pore water in soil cores from floodplains in the Netherlands and from less anthropogenically influenced floodplains from Poland. During the inundation experiment, concentrations of P in the pore water rose to 2-90 times the initial concentrations. P release was not directly related to the geographic origin of the soils. An important predictor variable of P release was found in the ratio between the concentration of iron-bound P and amorphous iron. This ratio may provide a practical tool for the selection of new areas for wetland creation, and for impact assessment of plans for riverine wetland restoration and floodwater storage. - Mobilisation of phosphorus in floodplain wetland soils can be predicted with easily measurable soil characteristics

  12. Prediction of phosphorus mobilisation in inundated floodplain soils

    Energy Technology Data Exchange (ETDEWEB)

    Loeb, Roos [Department of Aquatic Ecology and Environmental Biology, Institute for Water and Wetland Research, Radboud University Nijmegen, Toernooiveld 1, 6525 ED Nijmegen (Netherlands)], E-mail: r.loeb@science.ru.nl; Lamers, Leon P.M.; Roelofs, Jan G.M. [Department of Aquatic Ecology and Environmental Biology, Institute for Water and Wetland Research, Radboud University Nijmegen, Toernooiveld 1, 6525 ED Nijmegen (Netherlands)

    2008-11-15

    After flooding, iron reduction in riverine wetlands may cause the release of large quantities of phosphorus. As phosphorus is an important nutrient causing eutrophication in aquatic systems, it is important to have a tool to predict this potential release. In this study we examined the P release to the soil pore water in soil cores from floodplains in the Netherlands and from less anthropogenically influenced floodplains from Poland. During the inundation experiment, concentrations of P in the pore water rose to 2-90 times the initial concentrations. P release was not directly related to the geographic origin of the soils. An important predictor variable of P release was found in the ratio between the concentration of iron-bound P and amorphous iron. This ratio may provide a practical tool for the selection of new areas for wetland creation, and for impact assessment of plans for riverine wetland restoration and floodwater storage. - Mobilisation of phosphorus in floodplain wetland soils can be predicted with easily measurable soil characteristics.

  13. Mobilisation for public engagement: Benchmarking the practices of research institutes.

    Science.gov (United States)

    Entradas, Marta; Bauer, Martin M

    2017-10-01

    Studies on scientists' practices of public engagement have pointed to variations between disciplines. If variations at the individual level are reflected at the institutional level, then research institutes in Social Sciences (and Humanities) should perform higher in public engagement and be more involved in dialogue with the public. Using a nearly complete sample of research institutes in Portugal 2014 ( n = 234, 61% response rate), we investigate how public engagement varies in intensity, type of activities and target audiences across scientific areas. Three benchmark findings emerge. First, the Social Sciences and the Humanities profile differently in public engagement highlighting the importance of distinguishing between these two scientific areas often conflated in public engagement studies. Second, the Social Sciences overall perform more public engagement activities, but the Natural Sciences mobilise more effort for public engagement. Third, while the Social Sciences play a greater role in civic public engagement, the Natural Sciences are more likely to perform educational activities. Finally, this study shows that the overall size of research institutes, available public engagement funding and public engagement staffing make a difference in institutes' public engagement.

  14. Sensitivity analysis techniques applied to a system of hyperbolic conservation laws

    International Nuclear Information System (INIS)

    Weirs, V. Gregory; Kamm, James R.; Swiler, Laura P.; Tarantola, Stefano; Ratto, Marco; Adams, Brian M.; Rider, William J.; Eldred, Michael S.

    2012-01-01

    Sensitivity analysis is comprised of techniques to quantify the effects of the input variables on a set of outputs. In particular, sensitivity indices can be used to infer which input parameters most significantly affect the results of a computational model. With continually increasing computing power, sensitivity analysis has become an important technique by which to understand the behavior of large-scale computer simulations. Many sensitivity analysis methods rely on sampling from distributions of the inputs. Such sampling-based methods can be computationally expensive, requiring many evaluations of the simulation; in this case, the Sobol' method provides an easy and accurate way to compute variance-based measures, provided a sufficient number of model evaluations are available. As an alternative, meta-modeling approaches have been devised to approximate the response surface and estimate various measures of sensitivity. In this work, we consider a variety of sensitivity analysis methods, including different sampling strategies, different meta-models, and different ways of evaluating variance-based sensitivity indices. The problem we consider is the 1-D Riemann problem. By a careful choice of inputs, discontinuous solutions are obtained, leading to discontinuous response surfaces; such surfaces can be particularly problematic for meta-modeling approaches. The goal of this study is to compare the estimated sensitivity indices with exact values and to evaluate the convergence of these estimates with increasing samples sizes and under an increasing number of meta-model evaluations. - Highlights: ► Sensitivity analysis techniques for a model shock physics problem are compared. ► The model problem and the sensitivity analysis problem have exact solutions. ► Subtle details of the method for computing sensitivity indices can affect the results.

  15. Applying Squeezing Technique to Clayrocks: Lessons Learned from Experiments at Mont Terri Rock Laboratory

    International Nuclear Information System (INIS)

    Fernandez, A. M.; Sanchez-Ledesma, D. M.; Tournassat, C.; Melon, A.; Gaucher, E.; Astudillo, E.; Vinsot, A.

    2013-01-01

    Knowledge of the pore water chemistry in clay rock formations plays an important role in determining radionuclide migration in the context of nuclear waste disposal. Among the different in situ and ex-situ techniques for pore water sampling in clay sediments and soils, squeezing technique dates back 115 years. Although different studies have been performed about the reliability and representativeness of squeezed pore waters, more of them were achieved on high porosity, high water content and unconsolidated clay sediments. A very few of them tackled the analysis of squeezed pore water from low-porosity, low water content and highly consolidated clay rocks. In this work, a specially designed and fabricated one-dimensional compression cell two directional fluid flow was used to extract and analyse the pore water composition of Opalinus Clay core samples from Mont Terri (Switzerland). The reproducibility of the technique is good and no ionic ultrafiltration, chemical fractionation or anion exclusion was found in the range of pressures analysed: 70-200 MPa. Pore waters extracted in this range of pressures do not decrease in concentration, which would indicate a dilution of water by mixing of the free pore water and the outer layers of double layer water (Donnan water). A threshold (safety) squeezing pressure of 175 MPa was established for avoiding membrane effects (ion filtering, anion exclusion, etc.) from clay particles induced by increasing pressures. Besides, the pore waters extracted at these pressures are representative of the Opalinus Clay formation from a direct comparison against in situ collected borehole waters. (Author)

  16. Applying Squeezing Technique to Clayrocks: Lessons Learned from Experiments at Mont Terri Rock Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, A. M.; Sanchez-Ledesma, D. M.; Tournassat, C.; Melon, A.; Gaucher, E.; Astudillo, E.; Vinsot, A.

    2013-07-01

    Knowledge of the pore water chemistry in clay rock formations plays an important role in determining radionuclide migration in the context of nuclear waste disposal. Among the different in situ and ex-situ techniques for pore water sampling in clay sediments and soils, squeezing technique dates back 115 years. Although different studies have been performed about the reliability and representativeness of squeezed pore waters, more of them were achieved on high porosity, high water content and unconsolidated clay sediments. A very few of them tackled the analysis of squeezed pore water from low-porosity, low water content and highly consolidated clay rocks. In this work, a specially designed and fabricated one-dimensional compression cell two directional fluid flow was used to extract and analyse the pore water composition of Opalinus Clay core samples from Mont Terri (Switzerland). The reproducibility of the technique is good and no ionic ultrafiltration, chemical fractionation or anion exclusion was found in the range of pressures analysed: 70-200 MPa. Pore waters extracted in this range of pressures do not decrease in concentration, which would indicate a dilution of water by mixing of the free pore water and the outer layers of double layer water (Donnan water). A threshold (safety) squeezing pressure of 175 MPa was established for avoiding membrane effects (ion filtering, anion exclusion, etc.) from clay particles induced by increasing pressures. Besides, the pore waters extracted at these pressures are representative of the Opalinus Clay formation from a direct comparison against in situ collected borehole waters. (Author)

  17. Enhanced nonlinear iterative techniques applied to a non-equilibrium plasma flow

    Energy Technology Data Exchange (ETDEWEB)

    Knoll, D.A.; McHugh, P.R. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

    1996-12-31

    We study the application of enhanced nonlinear iterative methods to the steady-state solution of a system of two-dimensional convection-diffusion-reaction partial differential equations that describe the partially-ionized plasma flow in the boundary layer of a tokamak fusion reactor. This system of equations is characterized by multiple time and spatial scales, and contains highly anisotropic transport coefficients due to a strong imposed magnetic field. We use Newton`s method to linearize the nonlinear system of equations resulting from an implicit, finite volume discretization of the governing partial differential equations, on a staggered Cartesian mesh. The resulting linear systems are neither symmetric nor positive definite, and are poorly conditioned. Preconditioned Krylov iterative techniques are employed to solve these linear systems. We investigate both a modified and a matrix-free Newton-Krylov implementation, with the goal of reducing CPU cost associated with the numerical formation of the Jacobian. A combination of a damped iteration, one-way multigrid and a pseudo-transient continuation technique are used to enhance global nonlinear convergence and CPU efficiency. GMRES is employed as the Krylov method with Incomplete Lower-Upper(ILU) factorization preconditioning. The goal is to construct a combination of nonlinear and linear iterative techniques for this complex physical problem that optimizes trade-offs between robustness, CPU time, memory requirements, and code complexity. It is shown that a one-way multigrid implementation provides significant CPU savings for fine grid calculations. Performance comparisons of the modified Newton-Krylov and matrix-free Newton-Krylov algorithms will be presented.

  18. X-ray Computed Microtomography technique applied for cementitious materials: A review.

    Science.gov (United States)

    da Silva, Ítalo Batista

    2018-04-01

    The main objective of this article is to present a bibliographical review about the use of the X-ray microtomography method in 3D images processing of cementitious materials microstructure, analyzing the pores microstructure and connectivity network, enabling tthe possibility of building a relationship between permeability and porosity. The use of this technique enables the understanding of physical, chemical and mechanical properties of cementitious materials by publishing good results, considering that the quality and quantity of accessible information were significant and may contribute to the study of cementitious materials development. Copyright © 2018 Elsevier Ltd. All rights reserved.

  19. Some new techniques in tritium gas handling as applied to metal hydride synthesis

    International Nuclear Information System (INIS)

    Nasise, J.E.

    1988-01-01

    A state-of-the-art tritium Hydriding Synthesis System (HSS) was designed and built to replace the existing system within the Tritium Salt Facility (TSF) at the Los Alamos National Laboratory. This new hydriding system utilizes unique fast-cycling 7.9 mole uranium beds (47.5g of T at 100% loading) and novel gas circulating hydriding furnaces. Tritium system components discussed include fast-cycling uranium beds, circulating gas hydriding furnaces, valves, storage volumes, manifolds, gas transfer pumps, and graphic display and control consoles. Many of the tritium handling and processing techniques incorporated into this system are directly applicable to today's fusion fuel loops. 12 refs., 7 figs

  20. Organic acid derivatization techniques applied to petroleum hydrocarbon transformations in subsurface environments

    International Nuclear Information System (INIS)

    Barcelona, M.J.; Lu, J.; Tomczak, D.M.

    1995-01-01

    Evidence for the natural microbial remediation of subsurface fuel contamination situations should include identification and analysis of transformation or degradation products. In this way, a mass balance between fuel constituents and end products may be approached to monitor cleanup progress. Application of advanced organic acid metabolite derivatization techniques to several know sites of organic compounds and fuel mixture contamination provide valuable information on the pathways and progress of microbial transformation. Good correlation between observed metabolites and transformation pathways of aromatic fuel constituents were observed at the sites

  1. High speed resonant frequency determination applied to field mapping using perturbation techniques

    International Nuclear Information System (INIS)

    Smith, B.H.; Burton, R.J.; Hutcheon, R.M.

    1992-01-01

    Perturbation techniques are commonly used for measuring electric and magnetic field distributions in resonant structures. A field measurement system has been assembled using a Hewlett Packard model 8753C network analyzer interfaced via an HPIB bus to a personal computer to form an accurate, rapid and flexible system for data acquisition, control, and analysis of such measurements. Characterization of long linac structures (up to 3 m) is accomplished in about three minutes, minimizing thermal drift effects. This paper describes the system, its application and its extension to applications such as confirming the presence of weak, off-axis quadrupole fields in an on-axis coupled linac. (Author) 5 figs., 10 refs

  2. Study of different filtering techniques applied to spectra from airborne gamma spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Wilhelm, Emilien; Gutierrez, Sebastien; Reboli, Anne; Menard, Stephanie; Nourreddine, Abdel-Mjid [Commissariat a l' Energie Atomique et aux energies alternatives - CEA, DAM, DIF F-91297 Arpajon (France); Arbor, Nicolas [Institut Pluridisciplinaire Hubert Curien, UMR 7178 Universite de Strasbourg-CNRS, 23 rue du Loess, BP 28, F-67037 Strasbourg Cedex 2 (France)

    2015-07-01

    One of the features of spectra obtained by airborne gamma spectrometry is low counting statistics due to the short acquisition time (1 s) and the large source-detector distance (40 m). It leads to considerable uncertainty in radionuclide identification and determination of their respective activities from the windows method recommended by the IAEA, especially for low-level radioactivity. The present work compares the results obtained with filters in terms of errors of the filtered spectra with the window method and over the whole gamma energy range. The results are used to determine which filtering technique is the most suitable in combination with some method for total stripping of the spectrum. (authors)

  3. Nuclear analytical techniques applied to characterization of atmospheric aerosols in Amazon Region

    International Nuclear Information System (INIS)

    Gerab, Fabio; Artaxo, Paulo

    1996-01-01

    This work presents the atmospheric aerosols characterization that exist in different regions of Amazon basin. The biogenic aerosol emission by forest, as well as the atmospheric emissions of particulate materials due to biomass burning, were analyzed. Samples of aerosol particles were collected during three years in two different locations of Amazon region using Stacked Unit Filters. In order to study these samples some analytical nuclear techniques were used. The high concentrations of aerosols as a result of biomass burning process were observed in the period of june-september

  4. The differential dieaway technique applied to the measurement of the fissile content of drums of cement encapsulated waste

    International Nuclear Information System (INIS)

    Swinhoe, M.T.

    1986-01-01

    This report describes calculations of the differential dieaway technique as applied to cement encapsulated waste. The main difference from previous applications of the technique are that only one detector position is used (diametrically opposite the neutron source) and the chamber walls are made of concrete. The results show that by rotating the drum the response to fissile material across the central plane of the drum can be made relatively uniform. The absolute size of the response is about 0.4. counts per minute per gram fissile for a neutron source of 10 8 neutrons per second. Problems of neutron and gamma background and water content are considered. (author)

  5. Electrochemical noise measurements techniques and the reversing dc potential drop method applied to stress corrosion essays

    International Nuclear Information System (INIS)

    Aly, Omar Fernandes; Andrade, Arnaldo Paes de; MattarNeto, Miguel; Aoki, Idalina Vieira

    2002-01-01

    This paper aims to collect information and to discuss the electrochemical noise measurements and the reversing dc potential drop method, applied to stress corrosion essays that can be used to evaluate the nucleation and the increase of stress corrosion cracking in Alloy 600 and/or Alloy 182 specimens from Angra I Nuclear Power Plant. Therefore we will pretend to establish a standard procedure to essays to be realized on the new autoclave equipment on the Laboratorio de Eletroquimica e Corrosao do Departamento de Engenharia Quimica da Escola Politecnica da Universidade de Sao Paulo - Electrochemical and Corrosion Laboratory of the Chemical Engineering Department of Polytechnical School of Sao Paulo University, Brazil. (author)

  6. A review of post-modern management techniques as currently applied to Turkish forestry.

    Science.gov (United States)

    Dölarslan, Emre Sahin

    2009-01-01

    This paper reviews the effects of six post-modern management concepts as applied to Turkish forestry. Up to now, Turkish forestry has been constrained, both in terms of its operations and internal organization, by a highly bureaucratic system. The application of new thinking in forestry management, however, has recently resulted in new organizational and production concepts that promise to address problems specific to this Turkish industry and bring about positive changes. This paper will elucidate these specific issues and demonstrate how post-modern management thinking is influencing the administration and operational capacity of Turkish forestry within its current structure.

  7. Reduced order modelling techniques for mesh movement strategies as applied to fluid structure interactions

    CSIR Research Space (South Africa)

    Bogaers, Alfred EJ

    2010-01-01

    Full Text Available of Laplacian or Bi-harmonic equations [7], radial basis function (RBF) interpolation [3, 15] or through mesh optimization [1, 6]. Despite the successes of these algorithms in reducing the frequency and necessity for re- meshing, they still account for a... simulations of a real system. What makes POD remarkable is that the selected modes are not only appropriate but make up the optimal linear basis for describing any given system. POD has been applied in a wide range of disciplines including image processing...

  8. Microbiological evaluation of sludge during an improvement process applying the washing technique (selective pressure)

    International Nuclear Information System (INIS)

    Molina P, Francisco; Gonzalez, Maria Elena; Gonzalez, Luz Catalina

    2001-01-01

    In this investigation, the microbial consortiums were evaluated by using characterization by trophic groups and related groups by their sensibility to oxygen, as well as the specific methanogenic activity (SMA) of an acclimated sludge, starting from an aerobium sludge corning from a residual water treatment plant. Later, the technique of improvement by washing was applicated to this sludge, getting inoculum for the starting of an anaerobic reactor of the kind UASB (treatment reactor). At the same time, a control reactor was operated, inoculated with acclimated sludge. Both reactors were operated during 120 days, using brown sugar as substrate, the experimental phase included dates up to 70 operation days, characterizing the sludge at the end of this period. The SMA was analysed using acetic and formic acids as substrates. The results showed activities between 0,45 and 1,39 g DQO-CH 4 /SSV -d. for both substrates. At the end of the experimental phase of the UASB reactor, the sulphate reducer bacteria from the acetate and the lactate were observed as predominant group, followed by the methanogenic hydrogenophilic bacteria. It is important to notice that, with the application of the sludge washing technique, all the tropic groups were increased, with the exception of the lactate fermentative bacteria

  9. New tools, technology and techniques applied in geological sciences: current situation and future perspectives

    International Nuclear Information System (INIS)

    Ulloa, Andres

    2014-01-01

    Technological tools and work methodologies most used in the area of geological sciences are reviewed and described. The various electronic devices such as laptops, palmtops or PDA (personal digital assistant), tablets and smartphones have allowed to take field geological data and store them efficiently. Tablets and smartphones have been convenient for data collection of scientific data by the diversity of sensors that present, portability, autonomy and the possibility to install specific applications. High precision GPS in conjunction with LIDAR technology and sonar technology have been more accessible and used for geological research, generating high resolution three-dimensional models to complement geological studies. Remote sensing techniques such as high penetration radar are used to perform models of the ice thickness and topography in Antarctic. Modern three-dimensional scanning and printing techniques are used in geological science research and teaching. Currently, the advance in the computer technology has allowed to handle three-dimensional models on personal computers efficiently way and with different display options. Some, of the new areas of geology, emerged recently, are mentioned to generate a broad panorama toward where can direct geological researches in the next years [es

  10. Fragrance composition of Dendrophylax lindenii (Orchidaceae using a novel technique applied in situ

    Directory of Open Access Journals (Sweden)

    James J. Sadler

    2012-02-01

    Full Text Available The ghost orchid, Dendrophylax lindenii (Lindley Bentham ex Rolfe (Orchidaceae, is one of North America’s rarest and well-known orchids. Native to Cuba and SW Florida where it frequents shaded swamps as an epiphyte, the species has experienced steady decline. Little information exists on D. lindenii’s biology in situ, raising conservation concerns. During the summer of 2009 at an undisclosed population in Collier County, FL, a substantial number (ca. 13 of plants initiated anthesis offering a unique opportunity to study this species in situ. We report a new technique aimed at capturing floral headspace of D. lindenii in situ, and identified volatile compounds using gas chromatography mass spectrometry (GC/MS. All components of the floral scent were identified as terpenoids with the exception of methyl salicylate. The most abundant compound was the sesquiterpene (E,E-α-farnesene (71% followed by (E-β-ocimene (9% and methyl salicylate (8%. Other compounds were: linalool (5%, sabinene (4%, (E-α-bergamotene (2%, α-pinene (1%, and 3-carene (1%. Interestingly, (E,E-α-farnesene has previously been associated with pestiferous insects (e.g., Hemiptera. The other compounds are common floral scent constituents in other angiosperms suggesting that our in situ technique was effective. Volatile capture was, therefore, possible without imposing physical harm (e.g., inflorescence detachment to this rare orchid.

  11. MACHINE LEARNING TECHNIQUES APPLIED TO LIGNOCELLULOSIC ETHANOL IN SIMULTANEOUS HYDROLYSIS AND FERMENTATION

    Directory of Open Access Journals (Sweden)

    J. Fischer

    Full Text Available Abstract This paper investigates the use of machine learning (ML techniques to study the effect of different process conditions on ethanol production from lignocellulosic sugarcane bagasse biomass using S. cerevisiae in a simultaneous hydrolysis and fermentation (SHF process. The effects of temperature, enzyme concentration, biomass load, inoculum size and time were investigated using artificial neural networks, a C5.0 classification tree and random forest algorithms. The optimization of ethanol production was also evaluated. The results clearly depict that ML techniques can be used to evaluate the SHF (R2 between actual and model predictions higher than 0.90, absolute average deviation lower than 8.1% and RMSE lower than 0.80 and predict optimized conditions which are in close agreement with those found experimentally. Optimal conditions were found to be a temperature of 35 ºC, an SHF time of 36 h, enzymatic load of 99.8%, inoculum size of 29.5 g/L and bagasse concentration of 24.9%. The ethanol concentration and volumetric productivity for these conditions were 12.1 g/L and 0.336 g/L.h, respectively.

  12. Cavity Ring Down and Thermal Lens Techniques Applied to Vibrational Spectroscopy of Gases and Liquids

    Science.gov (United States)

    Nyaupane, Parashu Ram

    Infrared (IR) and near-infrared (NIR) region gas temperature sensors have been used in the past because of its non-intrusive character and fast time response. In this dissertation cavity ring down (CRD) absorption of oxygen around the region 760 nm has been used to measure the temperature of flowing air in an open optical cavity. This sensor could be a convenient method for measuring the temperature at the input (cold air) and output (hot air) after cooling the blades of a gas turbine. The results could contribute to improvements in turbine blade cooling designs. Additionally, it could be helpful for high temperature measurement in harsh conditions like flames, boilers, and industrial pyrolysis ovens as well as remote sensing. We are interested in experiments that simulate the liquid methane and ethane lakes on Titan which is around the temperature of 94 K. Our specific goal is to quantify the solubility of unsaturated hydrocarbons in liquid ethane and methane. However, it is rather complicated to do so because of the low temperatures, low solubility and solvent effects. So, it is wise to do the experiments at higher temperature and test the suitability of the techniques. In these projects, we were trying to explore if our existing laboratory techniques were sensitive enough to obtain the solubility of unsaturated hydrocarbons in liquid ethane. First, we studied the thermal lens spectroscopy (TLS) of the (Deltav = 6) C-H overtone of benzene and naphthalene in hexane and CCl4 at room temperature.

  13. Gamma-radiography techniques applied to quality control of welds in water pipe lines

    International Nuclear Information System (INIS)

    Sanchez, W.; Oki, H.

    1974-01-01

    Non-destructive testing of welds may be done by the gamma-radiography technique, in order to detect the presence or absence of discontinuities and defects in the bulk of deposited metal and near the base metal. Gamma-radiography allows the documentation of the test with a complete inspection record, which is a fact not common in other non-destructive testing methods. In the quality control of longitudinal or transversal welds in water pipe lines, two exposition techniques are used: double wall and panoramic exposition. Three different water pipe lines systems have analysed for weld defects, giving a total of 16,000 gamma-radiographies. The tests were made according to the criteria established by the ASME standard. The principal metallic discontinuites found in the weld were: porosity (32%), lack of penetration (29%), lack of fusion (20%), and slag inclusion (19%). The percentage of gamma-radiographies showing welds without defects was 39% (6168 gamma-radiographies). On the other hand, 53% (8502 gamma-radiographies) showed the presence of acceptable discontinuities and 8% (1330 gamma-radiographies) were rejected according to the ASME standards [pt

  14. Low-dimensional and Data Fusion Techniques Applied to a Rectangular Supersonic Multi-stream Jet

    Science.gov (United States)

    Berry, Matthew; Stack, Cory; Magstadt, Andrew; Ali, Mohd; Gaitonde, Datta; Glauser, Mark

    2017-11-01

    Low-dimensional models of experimental and simulation data for a complex supersonic jet were fused to reconstruct time-dependent proper orthogonal decomposition (POD) coefficients. The jet consists of a multi-stream rectangular single expansion ramp nozzle, containing a core stream operating at Mj , 1 = 1.6 , and bypass stream at Mj , 3 = 1.0 with an underlying deck. POD was applied to schlieren and PIV data to acquire the spatial basis functions. These eigenfunctions were projected onto their corresponding time-dependent large eddy simulation (LES) fields to reconstruct the temporal POD coefficients. This reconstruction was able to resolve spectral peaks that were previously aliased due to the slower sampling rates of the experiments. Additionally, dynamic mode decomposition (DMD) was applied to the experimental and LES datasets, and the spatio-temporal characteristics were compared to POD. The authors would like to acknowledge AFOSR, program manager Dr. Doug Smith, for funding this research, Grant No. FA9550-15-1-0435.

  15. Applying Tiab’s direct synthesis technique to dilatant non-Newtonian/Newtonian fluids

    Directory of Open Access Journals (Sweden)

    Javier Andrés Martínez

    2011-09-01

    Full Text Available Non-Newtonian fluids, such as polymer solutions, have been used by the oil industry for many years as fracturing agents and drilling mud. These solutions, which normally include thickened water and jelled fluids, are injected into the formation to enhanced oil recovery by improving sweep efficiency. It is worth noting that some heavy oils behave non-Newtonianly. Non-Newtonian fluids do not have direct proportionality between applied shear stress and shear rate and viscosity varies with shear rate depending on whether the fluid is either pseudoplastic or dilatant. Viscosity decreases as shear rate increases for the former whilst the reverse takes place for dilatants. Mathematical models of conventional fluids thus fail when applied to non-Newtonian fluids. The pressure derivative curve is introduced in this descriptive work for a dilatant fluid and its pattern was observed. Tiab’s direct synthesis (TDS methodology was used as a tool for interpreting pressure transient data to estimate effective permeability, skin factors and non-Newtonian bank radius. The methodology was successfully verified by its application to synthetic examples. Also, comparing it to pseudoplastic behavior, it was found that the radial flow regime in the Newtonian zone of dilatant fluids took longer to form regarding both the flow behavior index and consistency factor.

  16. A Systematic Approach to Applying Lean Techniques to Optimize an Office Process at the Y-12 National Security Complex

    Energy Technology Data Exchange (ETDEWEB)

    Credille, Jennifer [Y-12 National Security Complex, Oak Ridge, TN (United States); Univ. of Tennessee, Knoxville, TN (United States); Owens, Elizabeth [Y-12 National Security Complex, Oak Ridge, TN (United States); Univ. of Tennessee, Knoxville, TN (United States)

    2017-10-11

    This capstone offers the introduction of Lean concepts to an office activity to demonstrate the versatility of Lean. Traditionally Lean has been associated with process improvements as applied to an industrial atmosphere. However, this paper will demonstrate that implementing Lean concepts within an office activity can result in significant process improvements. Lean first emerged with the conception of the Toyota Production System. This innovative concept was designed to improve productivity in the automotive industry by eliminating waste and variation. Lean has also been applied to office environments, however the limited literature reveals most Lean techniques within an office are restricted to one or two techniques. Our capstone confronts these restrictions by introducing a systematic approach that utilizes multiple Lean concepts. The approach incorporates: system analysis, system reliability, system requirements, and system feasibility. The methodical Lean outline provides tools for a successful outcome, which ensures the process is thoroughly dissected and can be achieved for any process in any work environment.

  17. Mass Movement Hazards in the Mediterranean; A review on applied techniques and methodologies

    Science.gov (United States)

    Ziade, R.; Abdallah, C.; Baghdadi, N.

    2012-04-01

    Emergent population and expansions of settlements and life-lines over hazardous areas in the Mediterranean region have largely increased the impact of Mass Movements (MM) both in industrialized and developing countries. This trend is expected to continue in the next decades due to increased urbanization and development, continued deforestation and increased regional precipitation in MM-prone areas due to changing climatic patterns. Consequently, and over the past few years, monitoring of MM has acquired great importance from the scientific community as well as the civilian one. This article begins with a discussion of the MM classification, and the different topographic, geologic, hydrologic and environmental impacting factors. The intrinsic (preconditioning) variables determine the susceptibility of MM and extrinsic factors (triggering) can induce the probability of MM occurrence. The evolution of slope instability studies is charted from geodetic or observational techniques, to geotechnical field-based origins to recent higher levels of data acquisition through Remote Sensing (RS) and Geographic Information System (GIS) techniques. Since MM detection and zoning is difficult in remote areas, RS and GIS have enabled regional studies to predominate over site-based ones where they provide multi-temporal images hence facilitate greatly MM monitoring. The unusual extent of the spectrum of MM makes it difficult to define a single methodology to establish MM hazard. Since the probability of occurrence of MM is one of the key components in making rational decisions for management of MM risk, scientists and engineers have developed physical parameters, equations and environmental process models that can be used as assessment tools for management, education, planning and legislative purposes. Assessment of MM is attained through various modeling approaches mainly divided into three main sections: quantitative/Heuristic (1:2.000-1:10.000), semi-quantitative/Statistical (1

  18. A comparison of new, old and future densiometic techniques as applied to volcanologic study.

    Science.gov (United States)

    Pankhurst, Matthew; Moreland, William; Dobson, Kate; Þórðarson, Þorvaldur; Fitton, Godfrey; Lee, Peter

    2015-04-01

    The density of any material imposes a primary control upon its potential or actual physical behaviour in relation to its surrounds. It follows that a thorough understanding of the physical behaviour of dynamic, multi-component systems, such as active volcanoes, requires knowledge of the density of each component. If we are to accurately predict the physical behaviour of synthesized or natural volcanic systems, quantitative densiometric measurements are vital. The theoretical density of melt, crystals and bubble phases may be calculated using composition, structure, temperature and pressure inputs. However, measuring the density of natural, non-ideal, poly-phase materials remains problematic, especially if phase specific measurement is important. Here we compare three methods; Archimedes principle, He-displacement pycnometry and X-ray micro computed tomography (XMT) and discuss the utility and drawbacks of each in the context of modern volcanologic study. We have measured tephra, ash and lava from the 934 AD Eldgjá eruption (Iceland), and the 2010 AD Eyjafjallajökull eruption (Iceland), using each technique. These samples exhibit a range of particle sizes, phases and textures. We find that while the Archimedes method remains a useful, low-cost technique to generate whole-rock density data, relative precision is problematic at small particles sizes. Pycnometry offers a more precise whole-rock density value, at a comparable cost-per-sample. However, this technique is based upon the assumption pore spaces within the sample are equally available for gas exchange, which may or may not be the case. XMT produces 3D images, at resolutions from nm to tens of µm per voxel where X-ray attenuation is a qualitative measure of relative electron density, expressed as greyscale number/brightness (usually 16-bit). Phases and individual particles can be digitally segmented according to their greyscale and other characteristics. This represents a distinct advantage over both

  19. Tensometry technique for X-ray diffraction in applied analysis of welding

    International Nuclear Information System (INIS)

    Turibus, S.N.; Caldas, F.C.M.; Miranda, D.M.; Monine, V.I.; Assis, J.T.

    2010-01-01

    This paper presents the analysis of residual stress introduced in welding process. As the stress in a material can induce damages, it is necessary to have a method to identify this residual stress state. For this it was used the non-destructive X-ray diffraction technique to analyze two plates from A36 steel jointed by metal inert gas (MIG) welding. The stress measurements were made by the sin 2 ψ method in weld region of steel plates including analysis of longitudinal and transverse residual stresses in fusion zone, heat affected zone (HAZ) and base metal. To determine the stress distribution along the depth of the welded material it was used removing of superficial layers made by electropolishing. (author)

  20. An Encoding Technique for Multiobjective Evolutionary Algorithms Applied to Power Distribution System Reconfiguration

    Directory of Open Access Journals (Sweden)

    J. L. Guardado

    2014-01-01

    Full Text Available Network reconfiguration is an alternative to reduce power losses and optimize the operation of power distribution systems. In this paper, an encoding scheme for evolutionary algorithms is proposed in order to search efficiently for the Pareto-optimal solutions during the reconfiguration of power distribution systems considering multiobjective optimization. The encoding scheme is based on the edge window decoder (EWD technique, which was embedded in the Strength Pareto Evolutionary Algorithm 2 (SPEA2 and the Nondominated Sorting Genetic Algorithm II (NSGA-II. The effectiveness of the encoding scheme was proved by solving a test problem for which the true Pareto-optimal solutions are known in advance. In order to prove the practicability of the encoding scheme, a real distribution system was used to find the near Pareto-optimal solutions for different objective functions to optimize.

  1. Sensitivity Analysis Techniques Applied in Video Streaming Service on Eucalyptus Cloud Environments

    Directory of Open Access Journals (Sweden)

    Rosangela Melo

    2018-01-01

    Full Text Available Nowdays, several streaming servers are available to provide a variety of multimedia applications such as Video on Demand in cloud computing environments. These environments have the business potential because of the pay-per-use model, as well as the advantages of easy scalability and, up-to-date of the packages and programs. This paper uses hierarchical modeling and different sensitivity analysis techniques to determine the parameters that cause the greatest impact on the availability of a Video on Demand. The results show that distinct approaches provide similar results regarding the sensitivity ranking, with specific exceptions. A combined evaluation indicates that system availability may be improved effectively by focusing on a reduced set of factors that produce large variation on the measure of interest.

  2. Vibroacoustic Modeling of Mechanically Coupled Structures: Artificial Spring Technique Applied to Light and Heavy Mediums

    Directory of Open Access Journals (Sweden)

    L. Cheng

    1996-01-01

    Full Text Available This article deals with the modeling of vibrating structures immersed in both light and heavy fluids, and possible applications to noise control problems and industrial vessels containing fluids. A theoretical approach, using artificial spring systems to characterize the mechanical coupling between substructures, is extended to include fluid loading. A structure consisting of a plate-ended cylindrical shell and its enclosed acoustic cavity is analyzed. After a brief description of the proposed technique, a number of numerical results are presented. The analysis addresses the following specific issues: the coupling between the plate and the shell; the coupling between the structure and the enclosure; the possibilities and difficulties regarding internal soundproofing through modifications of the joint connections; and the effects of fluid loading on the vibration of the structure.

  3. Emerging and Innovative Techniques for Arsenic Removal Applied to a Small Water Supply System

    Directory of Open Access Journals (Sweden)

    António J. Alçada

    2009-12-01

    Full Text Available The impact of arsenic on human health has led its drinking water MCL to be drastically reduced from 50 to 10 ppb. Consequently, arsenic levels in many water supply sources have become critical. This has resulted in technical and operational impacts on many drinking water treatment plants that have required onerous upgrading to meet the new standard. This becomes a very sensitive issue in the context of water scarcity and climate change, given the expected increasing demand on groundwater sources. This work presents a case study that describes the development of low-cost techniques for efficient arsenic control in drinking water. The results obtained at the Manteigas WTP (Portugal demonstrate the successful implementation of an effective and flexible process of reactive filtration using iron oxide. At real-scale, very high removal efficiencies of over 95% were obtained.

  4. Hysteresis compensation technique applied to polymer optical fiber curvature sensor for lower limb exoskeletons

    Science.gov (United States)

    Gomes Leal-Junior, Arnaldo; Frizera-Neto, Anselmo; José Pontes, Maria; Rodrigues Botelho, Thomaz

    2017-12-01

    Polymer optical fiber (POF) curvature sensors present some advantages over conventional techniques for angle measurements, such as their light weight, compactness and immunity to electromagnetic fields. However, high hysteresis can occur in POF curvature sensors due to the polymer viscoelastic response. In order to overcome this limitation, this paper shows how the hysteresis sensor can be compensated by a calibration equation relating the measured output signal to the sensor’s angular velocity. The proposed method is validated using an exoskeleton with an active joint on the knee for flexion and extension rehabilitation exercises. The results show a decrease in sensor hysteresis and a decrease by more than two times in the error between the POF sensor and the potentiometer, which is employed for the angle measurement of the exoskeleton knee joint.

  5. The ring cycle: an iterative lens reconstruction technique applied to MG1131 + 0456

    International Nuclear Information System (INIS)

    Kochanek, C.S.; Blandford, R.D.; Lawrence, C.R.; Narayan, R.

    1989-01-01

    A new technique is described for the analysis of well-resolved gravitational lens images. This method allows us to solve for the brightness distribution of the unlensed source as well as a parametrized model of the lens. Our algorithm computes a figure of merit for a lens model based on the scatter in the surface brightnesses of image elements that, according to the model, come from the same source element. Minimization of the figure of merit leads to an optimum solution for the source and the lens. We present a successful application of the method to VLA maps of the 'Einstein ring' radio source MG1131 + 0456 observed by previous authors. The inversion gives a normal galaxy-like elliptical potential for the lens and an ordinary double-lobed structure for the background radio source. (author)

  6. An encoding technique for multiobjective evolutionary algorithms applied to power distribution system reconfiguration.

    Science.gov (United States)

    Guardado, J L; Rivas-Davalos, F; Torres, J; Maximov, S; Melgoza, E

    2014-01-01

    Network reconfiguration is an alternative to reduce power losses and optimize the operation of power distribution systems. In this paper, an encoding scheme for evolutionary algorithms is proposed in order to search efficiently for the Pareto-optimal solutions during the reconfiguration of power distribution systems considering multiobjective optimization. The encoding scheme is based on the edge window decoder (EWD) technique, which was embedded in the Strength Pareto Evolutionary Algorithm 2 (SPEA2) and the Nondominated Sorting Genetic Algorithm II (NSGA-II). The effectiveness of the encoding scheme was proved by solving a test problem for which the true Pareto-optimal solutions are known in advance. In order to prove the practicability of the encoding scheme, a real distribution system was used to find the near Pareto-optimal solutions for different objective functions to optimize.

  7. Inverse Optimization and Forecasting Techniques Applied to Decision-making in Electricity Markets

    DEFF Research Database (Denmark)

    Saez Gallego, Javier

    patterns that the load traditionally exhibited. On the other hand, this thesis is motivated by the decision-making processes of market players. In response to these challenges, this thesis provides mathematical models for decision-making under uncertainty in electricity markets. Demand-side bidding refers......This thesis deals with the development of new mathematical models that support the decision-making processes of market players. It addresses the problems of demand-side bidding, price-responsive load forecasting and reserve determination. From a methodological point of view, we investigate a novel...... approach to model the response of aggregate price-responsive load as a constrained optimization model, whose parameters are estimated from data by using inverse optimization techniques. The problems tackled in this dissertation are motivated, on one hand, by the increasing penetration of renewable energy...

  8. Automatic diameter control system applied to the laser heated pedestal growth technique

    Directory of Open Access Journals (Sweden)

    Andreeta M.R.B.

    2003-01-01

    Full Text Available We described an automatic diameter control system (ADC, for the laser heated pedestal growth technique, that reduces the diameter fluctuations in oxide fibers grown from unreacted and non-sinterized pedestals, to less than 2% of the average fiber diameter, and diminishes the average diameter fluctuation, over the entire length of the fiber, to less than 1%. The ADC apparatus is based on an artificial vision system that controls the pulling speed and the height of the molten zone within a precision of 30 mum. We also show that this system can be used for periodic in situ axial doping the fiber. Pure and Cr3+ doped LaAlO3 and pure LiNbO3 were usedas model materials.

  9. Models of signal validation using artificial intelligence techniques applied to a nuclear reactor

    International Nuclear Information System (INIS)

    Oliveira, Mauro V.; Schirru, Roberto

    2000-01-01

    This work presents two models of signal validation in which the analytical redundancy of the monitored signals from a nuclear plant is made by neural networks. In one model the analytical redundancy is made by only one neural network while in the other it is done by several neural networks, each one working in a specific part of the entire operation region of the plant. Four cluster techniques were tested to separate the entire operation region in several specific regions. An additional information of systems' reliability is supplied by a fuzzy inference system. The models were implemented in C language and tested with signals acquired from Angra I nuclear power plant, from its start to 100% of power. (author)

  10. Applying the sterile insect technique to the control of insect pests

    International Nuclear Information System (INIS)

    LaChance, L.E.; Klassen, W.

    1991-01-01

    The sterile insect technique (SIT) is basically a novel twentieth century approach to insect birth control. It is species specific and exploits the mate seeking behaviour of the insect. The basic principle is simple. Insects are mass reared in 'factories' and sexually sterilized by gamma rays from a 60 Co source. The sterile insects are then released in a controlled fashion into nature. Matings between the sterile insects released and native insects produced no progeny. If enough of these matings take place, reproduction of the pest population decreases. With continued release, the pest population can be controlled and in some cases eradicated. In the light of the many important applications of the SIT worldwide and the great potential that SIT concepts hold for insect and pest control in developing countries, two special benefits should be stressed. Of greatest significance is the fact that the SIT permits suppression and eradication of insect pests in an environmentally harmless manner. It combines nuclear techniques with genetic approaches and, in effect, replaces intensive use of chemicals in pest control. Although chemicals are used sparingly at the outset in some SIT programmes to reduce the size of the pest population before releases of sterilized insects are started, the total amount of chemicals used in an SIT programme is a mere fraction of what would be used without the SIT. It is also of great importance that the SIT is not designed strictly for the eradication of pest species but can readily be used in the suppression of insect populations. In fact, the SIT is ideally suited for use in conjunction with other agricultural pest control practices such as the use of parasites and predators, attractants and cultural controls (e.g. ploughing under or destruction of crop residues) in integrated pest management programmes to achieve control at the lowest possible price and with a minimum of chemical contamination of the environment

  11. Applying inversion techniques to derive source currents and geoelectric fields for geomagnetically induced current calculations

    Directory of Open Access Journals (Sweden)

    J. S. de Villiers

    2014-10-01

    Full Text Available This research focuses on the inversion of geomagnetic variation field measurement to obtain source currents in the ionosphere. During a geomagnetic disturbance, the ionospheric currents create magnetic field variations that induce geoelectric fields, which drive geomagnetically induced currents (GIC in power systems. These GIC may disturb the operation of power systems and cause damage to grounded power transformers. The geoelectric fields at any location of interest can be determined from the source currents in the ionosphere through a solution of the forward problem. Line currents running east–west along given surface position are postulated to exist at a certain height above the Earth's surface. This physical arrangement results in the fields on the ground having the magnetic north and down components, and the electric east component. Ionospheric currents are modelled by inverting Fourier integrals (over the wavenumber of elementary geomagnetic fields using the Levenberg–Marquardt technique. The output parameters of the inversion model are the current strength, height and surface position of the ionospheric current system. A ground conductivity structure with five layers from Quebec, Canada, based on the Layered-Earth model is used to obtain the complex skin depth at a given angular frequency. This paper presents preliminary and inversion results based on these structures and simulated geomagnetic fields. The results show some interesting features in the frequency domain. Model parameters obtained through inversion are within 2% of simulated values. This technique has applications for modelling the currents of electrojets at the equator and auroral regions, as well as currents in the magnetosphere.

  12. Study on structural design technique of silicon carbide applied for thermochemical hydrogen production IS process

    International Nuclear Information System (INIS)

    Takegami, Hiroaki; Terada, Atsuhiko; Inagaki, Yoshiyuki; Ishikura, Syuichi

    2011-03-01

    The IS process is the hydrogen production method which used the thermochemical reaction cycle of sulfuric acid and iodyne. Therefore, the design to endure the high temperature and moreover corrode-able environment is required to the equipment. Specifically, the sulfuric acid decomposer which is one of the main equipment of the IS process is the equipment to heat with hot helium and for the sulfuric acid of 90 wt% to evaporate. Moreover, it is the important equipment to supply the SO 3 decomposer which is the following process, resolving the part of sulfuric acid vapor into SO 3 with. The heat exchanger that sulfuric acid evaporates must be made pressure-resistant structure because it has the high-pressure helium of 4 MPa and the material that the high temperature and the corrosion environment of equal to or more than 700degC can be endured must be used. As the material, it is selected from the corrosion experiment and so on when SiC which is carbonization silicone ceramics is the most excellent material. However, even if it damages the ceramic block which is a heat exchanger because it becomes the structure which is stored in pressure-resistant metallic container, fluid such as sulfuric acid becomes the structure which doesn't leak out outside. However, the structure design technique to have been unified when using ceramics as the structure part isn't serviced as the standard. This report is the one which was studied about the structural design technique to have taken the material strength characteristic of the ceramics into consideration, refer to existing structural design standard. (author)

  13. Nuclear analytical techniques applied to the large scale measurements of atmospheric aerosols in the amazon region

    International Nuclear Information System (INIS)

    Gerab, Fabio

    1996-03-01

    This work presents the characterization of the atmosphere aerosol collected in different places of the Amazon Basin. We studied both the biogenic emission from the forest and the particulate material which is emitted to the atmosphere due to the large scale man-made burning during the dry season. The samples were collected during a three year period at two different locations in the Amazon, namely the Alta Floresta (MT) and Serra do Navio (AP) regions, using stacked unit filters. These regions represent two different atmospheric compositions: the aerosol is dominated by the forest natural biogenic emission at Serra do Navio, while at Alta Floresta it presents an important contribution from the man-made burning during the dry season. At Alta Floresta we took samples in gold in order to characterize mercury emission to the atmosphere related to the gold prospection activity in Amazon. Airplanes were used for aerosol sampling during the 1992 and 1993 dry seasons to characterize the atmospheric aerosol contents from man-made burning in large Amazonian areas. The samples were analyzed using several nuclear analytic techniques: Particle Induced X-ray Emission for the quantitative analysis of trace elements with atomic number above 11; Particle Induced Gamma-ray Emission for the quantitative analysis of Na; and Proton Microprobe was used for the characterization of individual particles of the aerosol. Reflectancy technique was used in the black carbon quantification, gravimetric analysis to determine the total atmospheric aerosol concentration and Cold Vapor Atomic Absorption Spectroscopy for quantitative analysis of mercury in the particulate from the Alta Floresta gold shops. Ionic chromatography was used to quantify ionic contents of aerosols from the fine mode particulate samples from Serra do Navio. Multivariate statistical analysis was used in order to identify and characterize the sources of the atmospheric aerosol present in the sampled regions. (author)

  14. Applying the sterile insect technique to the control of insect pests

    Energy Technology Data Exchange (ETDEWEB)

    LaChance, L E; Klassen, W [Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture, Vienna (Austria)

    1991-09-01

    The sterile insect technique (SIT) is basically a novel twentieth century approach to insect birth control. It is species specific and exploits the mate seeking behaviour of the insect. The basic principle is simple. Insects are mass reared in 'factories' and sexually sterilized by gamma rays from a {sup 60}Co source. The sterile insects are then released in a controlled fashion into nature. Matings between the sterile insects released and native insects produced no progeny. If enough of these matings take place, reproduction of the pest population decreases. With continued release, the pest population can be controlled and in some cases eradicated. In the light of the many important applications of the SIT worldwide and the great potential that SIT concepts hold for insect and pest control in developing countries, two special benefits should be stressed. Of greatest significance is the fact that the SIT permits suppression and eradication of insect pests in an environmentally harmless manner. It combines nuclear techniques with genetic approaches and, in effect, replaces intensive use of chemicals in pest control. Although chemicals are used sparingly at the outset in some SIT programmes to reduce the size of the pest population before releases of sterilized insects are started, the total amount of chemicals used in an SIT programme is a mere fraction of what would be used without the SIT. It is also of great importance that the SIT is not designed strictly for the eradication of pest species but can readily be used in the suppression of insect populations. In fact, the SIT is ideally suited for use in conjunction with other agricultural pest control practices such as the use of parasites and predators, attractants and cultural controls (e.g. ploughing under or destruction of crop residues) in integrated pest management programmes to achieve control at the lowest possible price and with a minimum of chemical contamination of the environment.

  15. Applied anatomy of a new approach of endoscopic technique in thyroid gland surgery.

    Science.gov (United States)

    Liu, Hong; Xie, Yong-jun; Xu, Yi-quan; Li, Chao; Liu, Xing-guo

    2012-10-01

    To explore the feasibility and safety of transtracheal assisted sublingual approach to totally endoscopic thyroidectomy by studying the anatomical approach and adjacent structures. A total of 5 embalmed adult cadavers from Chengdu Medical College were dissected layer by layer in the cervical region, pharyngeal region, and mandible region, according to transtracheal assisted sublingual approach that was verified from the anatomical approach and planes. A total of 15 embalmed adult cadavers were dissected by arterial vascular casting technique, imaging scanning technique, and thin layer cryotomy. Then the vessel and anatomical structures of thyroid surgical region were analyzed qualitatively and quantitatively. Three-dimensional visualization of larynx artery was reconstructed by Autodesk 3ds Max 2010(32). Transtracheal assisted sublingual approach for totally endoscopic thyroidectomy was simulated on 5 embalmed adult cadavers. The sublingual observed access was located in the middle of sublingual region. The geniohyoid muscle, mylohyoid seam, and submental triangle were divided in turn in the middle to reach the plane under the plastima muscles. Superficial cervical fascia, anterior body of hyoid bone, and infrahyoid muscles were passed in sequence to reach thyroid gland surgical region. The transtracheal operational access was placed from the cavitas oris propria, isthmus faucium, subepiglottic region, laryngeal pharynx, and intermediate laryngeal cavit, and then passed from the top down in order to reach pars cervicalis tracheae where a sagittal incision was made in the anterior wall of cartilagines tracheales to reach a ascertained surgical region. Transtracheal assisted sublingual approach to totally endoscopic thyroidectomy is anatomically feasible and safe and can be useful in thyroid gland surgery.

  16. Possibility of choosing development investment programs of a production company by applying discounted investment appraisal technique

    Directory of Open Access Journals (Sweden)

    Vesić-Vasović Jasmina

    2014-01-01

    Full Text Available The selection of development investment programs is one of the most important decisions in industrial production. The paper sets out the possibilities of applying dynamic criteria for investment decision making. It presents a practical numerical example for the value calculation of investment criteria Net Present Value and Internal Rate of Return for the reviewed investment project solutions. In this manner it is possible to make an orderly set of alternatives with clear preferences for the most suitable alternative in comparison with other ones. Such rating of project solutions will enable the decision maker to emphasize advantages with more arguments and select the most suitable project solution in accordance with the established criteria, conditions and limitations.

  17. A Research on Determination of Lecithin in Eggs by Applying Microwave Digestion Techniques and Spectrophotometry

    International Nuclear Information System (INIS)

    Wu, M.; Ge, Q.L.; Gao, Y. Sh.; Chen, K. W.

    2012-01-01

    A method to quick detect concentration of lecithin in eggs, namely microwave digestion spectrophotometry, was established in this research. The homogenate of eggs was treated with absolute ethanol to eliminate phosphate protein in eggs which could possibly affect concentration of lecithin examined. A sample then received a new way of pre-treatment, called microwave digestion, before UV-Vis spectrometry was applied to examine the concentration of phosphate at 400 nm. The linear equation was A = 0.08628X (μg), the corresponding coefficient of correlation was 0.9998, the detection limit of phosphorous was 0.2μg (n=11). The content of lecithin in eggs was then obtained. According to the result, the recovery of 90% was secured; therefore the conclusion of high degree of accuracy was reached.

  18. Applying stakeholder Delphi techniques for planning sustainable use of aquatic resources

    DEFF Research Database (Denmark)

    Lund, Søren; Banta, Gary Thomas; Bunting, Stuart W

    2015-01-01

    and Vietnam. The purpose of this paper is to give an account of how the stakeholder Delphi method was adapted and applied to support the participatory integrated action planning for sustainable use of aquatic resources facilitated within the HighARCS project. An account of the steps taken and results recorded......The HighARCS (Highland Aquatic Resources Conservation and Sustainable Development) project was a participatory research effort to map and better understand the patterns of resource use and livelihoods of communities who utilize highland aquatic resources in five sites across China, India...... of the stakeholder Delphi requires the presence of multidisciplinary and facilitating skills and competences within the implementing teams which should be considered before deciding to include a Stakeholder Delphi as a decision-making tool...

  19. Inverting travel times with a triplication. [spline fitting technique applied to lunar seismic data reduction

    Science.gov (United States)

    Jarosch, H. S.

    1982-01-01

    A method based on the use of constrained spline fits is used to overcome the difficulties arising when body-wave data in the form of T-delta are reduced to the tau-p form in the presence of cusps. In comparison with unconstrained spline fits, the method proposed here tends to produce much smoother models which lie approximately in the middle of the bounds produced by the extremal method. The method is noniterative and, therefore, computationally efficient. The method is applied to the lunar seismic data, where at least one triplication is presumed to occur in the P-wave travel-time curve. It is shown, however, that because of an insufficient number of data points for events close to the antipode of the center of the lunar network, the present analysis is not accurate enough to resolve the problem of a possible lunar core.

  20. Condition monitoring and signature analysis techniques as applied to Madras Atomic Power Station (MAPS) [Paper No.: VIA - 1

    International Nuclear Information System (INIS)

    Rangarajan, V.; Suryanarayana, L.

    1981-01-01

    The technique of vibration signature analysis for identifying the machine troubles in their early stages is explained. The advantage is that a timely corrective action can be planned to avoid breakdowns and unplanned shutdowns. At the Madras Atomic Power Station (MAPS), this technique is applied to regularly monitor vibrations of equipment and thus is serving as a tool for doing corrective maintenance of equipment. Case studies of application of this technique to main boiler feed pumps, moderation pump motors, centrifugal chiller, ventilation system fans, thermal shield ventilation fans, filtered water pumps, emergency process sea water pumps, and antifriction bearings of MAPS are presented. Condition monitoring during commissioning and subsequent operation could indicate defects. Corrective actions which were taken are described. (M.G.B.)

  1. Discrete classification technique applied to TV advertisements liking recognition system based on low-cost EEG headsets.

    Science.gov (United States)

    Soria Morillo, Luis M; Alvarez-Garcia, Juan A; Gonzalez-Abril, Luis; Ortega Ramírez, Juan A

    2016-07-15

    In this paper a new approach is applied to the area of marketing research. The aim of this paper is to recognize how brain activity responds during the visualization of short video advertisements using discrete classification techniques. By means of low cost electroencephalography devices (EEG), the activation level of some brain regions have been studied while the ads are shown to users. We may wonder about how useful is the use of neuroscience knowledge in marketing, or what could provide neuroscience to marketing sector, or why this approach can improve the accuracy and the final user acceptance compared to other works. By using discrete techniques over EEG frequency bands of a generated dataset, C4.5, ANN and the new recognition system based on Ameva, a discretization algorithm, is applied to obtain the score given by subjects to each TV ad. The proposed technique allows to reach more than 75 % of accuracy, which is an excellent result taking into account the typology of EEG sensors used in this work. Furthermore, the time consumption of the algorithm proposed is reduced up to 30 % compared to other techniques presented in this paper. This bring about a battery lifetime improvement on the devices where the algorithm is running, extending the experience in the ubiquitous context where the new approach has been tested.

  2. Large-timestep techniques for particle-in-cell simulation of systems with applied fields that vary rapidly in space

    International Nuclear Information System (INIS)

    Friedman, A.; Grote, D.P.

    1996-10-01

    Under conditions which arise commonly in space-charge-dominated beam applications, the applied focusing, bending, and accelerating fields vary rapidly with axial position, while the self-fields (which are, on average, comparable in strength to the applied fields) vary smoothly. In such cases it is desirable to employ timesteps which advance the particles over distances greater than the characteristic scales over which the applied fields vary. Several related concepts are potentially applicable: sub-cycling of the particle advance relative to the field solution, a higher-order time-advance algorithm, force-averaging by integration along approximate orbits, and orbit-averaging. We report on our investigations into the utility of such techniques for systems typical of those encountered in accelerator studies for heavy-ion beam-driven inertial fusion

  3. Analysis and simulation of wireless signal propagation applying geostatistical interpolation techniques

    Science.gov (United States)

    Kolyaie, S.; Yaghooti, M.; Majidi, G.

    2011-12-01

    This paper is a part of an ongoing research to examine the capability of geostatistical analysis for mobile networks coverage prediction, simulation and tuning. Mobile network coverage predictions are used to find network coverage gaps and areas with poor serviceability. They are essential data for engineering and management in order to make better decision regarding rollout, planning and optimisation of mobile networks.The objective of this research is to evaluate different interpolation techniques in coverage prediction. In method presented here, raw data collected from drive testing a sample of roads in study area is analysed and various continuous surfaces are created using different interpolation methods. Two general interpolation methods are used in this paper with different variables; first, Inverse Distance Weighting (IDW) with various powers and number of neighbours and second, ordinary kriging with Gaussian, spherical, circular and exponential semivariogram models with different number of neighbours. For the result comparison, we have used check points coming from the same drive test data. Prediction values for check points are extracted from each surface and the differences with actual value are computed. The output of this research helps finding an optimised and accurate model for coverage prediction.

  4. Applying Lean Techniques to Reduce Intravenous Waste Through Premixed Solutions and Increasing Production Frequency.

    Science.gov (United States)

    Lin, Alex C; Penm, Jonathan; Ivey, Marianne F; Deng, Yihong; Commins, Monica

    This study aims to use lean techniques and evaluate the impact of increasing the use of premixed IV solutions and increased IV production frequency on IV waste. Study was conducted at a tertiary hospital pharmacy department in three phases. Phase I included evaluation of IV waste when IV production occurred three times a day and eight premixed IV products were used. Phase II increased the number of premixed IV products to 16. Phase III then increased IV production to five times a day. During Phase I, an estimate of 2,673 IV doses were wasted monthly, accounting for 6.14% of overall IV doses. This accounted for 688 L that cost $60,135. During Phase II, the average monthly IV wastage reduced significantly to 1,069 doses (2.84%), accounting for 447 L and $34,003. During Phase III, the average monthly IV wastage was further decreased to 675 doses (1.69%), accounting for 78 L and $3,431. Hence, a potential annual saving of $449,208 could result from these changes. IV waste was reduced through the increased use of premixed solutions and increasing IV production frequency.

  5. The substitution technique applied for determining the parameters of a reactor with void

    International Nuclear Information System (INIS)

    Zdravkovic, Z.; Ivkovic, M.; Sotic, O.

    1965-12-01

    The material buckling of D 2 O-enriched uranium (2% U 235 ) system with voided fuel assembly has been determined by means of the substitution technique. The experiments were carried out in the zero power reactor RB for various lattice pitches, namely: 11.3 cm, 14 cm, and 16 cm. As a reference core the D 2 O-enriched uranium (2%U 235 ) ) system without voids has been used. The results have been analysed by the modified one-group perturbation theory using three regions in a substituted reactor (test, intermediate and reference). The perturbations in axial and radial directions due to voided fuel assembly, are also considered. In order to determine the change between diffusion coefficients in various regions (δD), additional experiments with single test fuel element were made. The lattice pitches of reference and test regions were the same. According to the algorithms given in appendices, the programmes for the ZUSE Z-23 digital computer were made. These programmes include evaluations of the change between diffusion coefficients (δD), and the axial buckling of the test lattice (author)

  6. Techniques for applying subatmospheric pressure dressing to wounds in difficult regions of anatomy.

    Science.gov (United States)

    Greer, S E; Duthie, E; Cartolano, B; Koehler, K M; Maydick-Youngberg, D; Longaker, M T

    1999-09-01

    Subatmospheric pressure dressing (SPD) has been commercially available in the United States since 1995 as the vacuum-assisted closure (VAC) device. SPD increases local blood flow, decreases edema and bacterial count, and promotes the formation of granulation tissue. Despite recent clinical successes with the use of SPD in a variety of wound types, problems may occur with application of VAC system in certain areas of the body. The main limitation occurs when attempting to maintain an airtight seal over irregular surfaces surrounding a wound. For example, application of the adhesive drape and creation of a seal are particularly difficulty in the hip and perineum. In addition, wounds of the lower extremity can occur in multiple sites, posing the problem of providing a vacuum dressing to more than one wound from one suction pump machine. To address these challenging clinical wounds, we have developed techniques to allow the successful application of SPD to sacral pressure ulcers near the anus, and to multiple large lower extremity ulcers.

  7. Data smoothing techniques applied to proton microprobe scans of teleost hard parts

    International Nuclear Information System (INIS)

    West, I.F.; Gauldie, R.W.; Coote, G.E.

    1992-01-01

    We use a proton microprobe to examine the distribution of elements in otoliths and scales of teleost (bony) fish. The elements of principal interest are calcium and strontium in otoliths and calcium and fluorine in scales. Changes in the distribution of these elements across hard structures may allow inferences about the life histories of fish. Otoliths and scales of interest are up to a centimeter in linear dimension and to reveal the structures of interest up to 200 sampling points are required in each dimension. The time needed to accumulate high X-ray counts at each sampling point can be large, particularly for strontium. To reduce microprobe usage we use data smoothing techniques to reveal changing patterns with modest X-ray count accumulations at individual data points. In this paper we review performance for revealing pattern at modest levels of X-ray count accumulations of a selection of digital filters (moving average smoothers), running median filters, robust locally weighted regression filters and adaptive spline filters. (author)

  8. Dosimetric properties of bio minerals applied to high-dose dosimetry using the TSEE technique

    International Nuclear Information System (INIS)

    Vila, G. B.; Caldas, L. V. E.

    2014-08-01

    The study of the dosimetric properties such as reproducibility, the residual signal, lower detection dose, dose-response curve and fading of the thermally stimulated emission exo electronic (TSEE) signal of Brazilian bio minerals has shown that these materials present a potential use as radiation dosimeters. The reproducibility within ± 10% for oyster shell, mother-of-pearl and coral reef samples showed that the signal dispersion is small when compared with the mean value of the measurements. The study showed that the residual signal can be eliminated with a thermal treatment at 300 grades C/1 h. The lower detection dose of 9.8 Gy determined for the oyster shell samples when exposed to beta radiation and 1.6 Gy for oyster shell and mother-of-pearl samples when exposed to gamma radiation can be considered good, taking into account the high doses of this study. The materials presented linearity at the dose response curves in some ranges, but the lack of linearity in other cases presents no problem since a good mathematical description is possible. The fading study showed that the loss of TSEE signal can be minimized if the samples are protected from interferences such as light, heat and humidity. Taking into account the useful linearity range as the main dosimetric characteristic, the tiger shell and oyster shell samples are the most suitable for high-dose dosimetry using the TSEE technique. (Author)

  9. Digital Image Correlation Techniques Applied to Large Scale Rocket Engine Testing

    Science.gov (United States)

    Gradl, Paul R.

    2016-01-01

    Rocket engine hot-fire ground testing is necessary to understand component performance, reliability and engine system interactions during development. The J-2X upper stage engine completed a series of developmental hot-fire tests that derived performance of the engine and components, validated analytical models and provided the necessary data to identify where design changes, process improvements and technology development were needed. The J-2X development engines were heavily instrumented to provide the data necessary to support these activities which enabled the team to investigate any anomalies experienced during the test program. This paper describes the development of an optical digital image correlation technique to augment the data provided by traditional strain gauges which are prone to debonding at elevated temperatures and limited to localized measurements. The feasibility of this optical measurement system was demonstrated during full scale hot-fire testing of J-2X, during which a digital image correlation system, incorporating a pair of high speed cameras to measure three-dimensional, real-time displacements and strains was installed and operated under the extreme environments present on the test stand. The camera and facility setup, pre-test calibrations, data collection, hot-fire test data collection and post-test analysis and results are presented in this paper.

  10. Delamination of plasters applied to historical masonry walls: analysis by acoustic emission technique and numerical model

    Science.gov (United States)

    Grazzini, A.; Lacidogna, G.; Valente, S.; Accornero, F.

    2018-06-01

    Masonry walls of historical buildings are subject to rising damp effects due to capillary or rain infiltrations, which in the time produce decay and delamination of historical plasters. In the restoration of masonry buildings, the plaster detachment frequently occurs because of mechanical incompatibility in repair mortar. An innovative laboratory procedure is described for test mechanical adhesion of new repair mortars. Compression static tests were carried out on composite specimens stone block-repair mortar, which specific geometry can test the de-bonding process of mortar in adherence with a stone masonry structure. The acoustic emission (AE) technique was employed for estimating the amount of energy released from fracture propagation in adherence surface between mortar and stone. A numerical simulation was elaborated based on the cohesive crack model. The evolution of detachment process of mortar in a coupled stone brick-mortar system was analysed by triangulation of AE signals, which can improve the numerical model and predict the type of failure in the adhesion surface of repair plaster. Through the cohesive crack model, it was possible to interpret theoretically the de-bonding phenomena occurring at the interface between stone block and mortar. Therefore, the mechanical behaviour of the interface is characterized.

  11. A Morphing Technique Applied to Lung Motions in Radiotherapy: Preliminary Results

    Directory of Open Access Journals (Sweden)

    R. Laurent

    2010-01-01

    Full Text Available Organ motion leads to dosimetric uncertainties during a patient’s treatment. Much work has been done to quantify the dosimetric effects of lung movement during radiation treatment. There is a particular need for a good description and prediction of organ motion. To describe lung motion more precisely, we have examined the possibility of using a computer technique: a morphing algorithm. Morphing is an iterative method which consists of blending one image into another image. To evaluate the use of morphing, Four Dimensions Computed Tomography (4DCT acquisition of a patient was performed. The lungs were automatically segmented for different phases, and morphing was performed using the end-inspiration and the end-expiration phase scans only. Intermediate morphing files were compared with 4DCT intermediate images. The results showed good agreement between morphing images and 4DCT images: fewer than 2 % of the 512 by 256 voxels were wrongly classified as belonging/not belonging to a lung section. This paper presents preliminary results, and our morphing algorithm needs improvement. We can infer that morphing offers considerable advantages in terms of radiation protection of the patient during the diagnosis phase, handling of artifacts, definition of organ contours and description of organ motion.

  12. Dosimetric properties of bio minerals applied to high-dose dosimetry using the TSEE technique

    Energy Technology Data Exchange (ETDEWEB)

    Vila, G. B.; Caldas, L. V. E., E-mail: gbvila@ipen.br [Instituto de Pesquisas Energeticas e Nucleares / CNEN, Av. Lineu Prestes 2242, Cidade Universitaria, 05508-000 Sao Paulo (Brazil)

    2014-08-15

    The study of the dosimetric properties such as reproducibility, the residual signal, lower detection dose, dose-response curve and fading of the thermally stimulated emission exo electronic (TSEE) signal of Brazilian bio minerals has shown that these materials present a potential use as radiation dosimeters. The reproducibility within ± 10% for oyster shell, mother-of-pearl and coral reef samples showed that the signal dispersion is small when compared with the mean value of the measurements. The study showed that the residual signal can be eliminated with a thermal treatment at 300 grades C/1 h. The lower detection dose of 9.8 Gy determined for the oyster shell samples when exposed to beta radiation and 1.6 Gy for oyster shell and mother-of-pearl samples when exposed to gamma radiation can be considered good, taking into account the high doses of this study. The materials presented linearity at the dose response curves in some ranges, but the lack of linearity in other cases presents no problem since a good mathematical description is possible. The fading study showed that the loss of TSEE signal can be minimized if the samples are protected from interferences such as light, heat and humidity. Taking into account the useful linearity range as the main dosimetric characteristic, the tiger shell and oyster shell samples are the most suitable for high-dose dosimetry using the TSEE technique. (Author)

  13. From birds to bees: applying video observation techniques to invertebrate pollinators

    Directory of Open Access Journals (Sweden)

    C J Lortie

    2012-01-01

    Full Text Available Observation is a critical element of behavioural ecology and ethology. Here, we propose a similar set of techniques to enhance the study of the diversity patterns of invertebrate pollinators and associated plant species. In a body of avian research, cameras are set up on nests in blinds to examine chick and parent interactions. This avoids observer bias, minimizes interference, and provides numerous other benefits including timestamps, the capacity to record frequency and duration of activities, and provides a permanent archive of activity for later analyses. Hence, we propose that small video cameras in blinds can also be used to continuously monitor pollinator activity on plants thereby capitalizing on those same benefits. This method was proofed in 2010 in the alpine in BC, Canada on target focal plant species and on open mixed assemblages of plant species. Apple ipod nanos successfully recorded activity for an entire day at a time totalling 450 hours and provided sufficient resolution and field of view to both identify pollinators to recognizable taxonomic units and monitor movement and visitation rates at a scale of view of approximately 50 cm2. This method is not a replacement for pan traps or sweep nets but an opportunity to enhance these datasets with more detailed, finer-resolution data. Importantly, the test of this specific method also indicates that far more hours of observation - using any method - are likely required than most current ecological studies published to accurately estimate pollinator diversity.

  14. The substitution technique applied for determining the parameters of a reactor with void

    Energy Technology Data Exchange (ETDEWEB)

    Zdravkovic, Z; Ivkovic, M; Sotic, O [Institute of nuclear sciences Boris Kidric, Vinca, Beograd (Yugoslavia)

    1965-12-15

    The material buckling of D{sub 2}O-enriched uranium (2% U{sub 235}) system with voided fuel assembly has been determined by means of the substitution technique. The experiments were carried out in the zero power reactor RB for various lattice pitches, namely: 11.3 cm, 14 cm, and 16 cm. As a reference core the D{sub 2}O-enriched uranium (2%U{sub 235}) ) system without voids has been used. The results have been analysed by the modified one-group perturbation theory using three regions in a substituted reactor (test, intermediate and reference). The perturbations in axial and radial directions due to voided fuel assembly, are also considered. In order to determine the change between diffusion coefficients in various regions ({delta}D), additional experiments with single test fuel element were made. The lattice pitches of reference and test regions were the same. According to the algorithms given in appendices, the programmes for the ZUSE Z-23 digital computer were made. These programmes include evaluations of the change between diffusion coefficients ({delta}D), and the axial buckling of the test lattice (author)

  15. Imaging techniques applied to the study of fluids in porous media

    Energy Technology Data Exchange (ETDEWEB)

    Tomutsa, L.; Doughty, D.; Mahmood, S.; Brinkmeyer, A.; Madden, M.P.

    1991-01-01

    A detailed understanding of rock structure and its influence on fluid entrapment, storage capacity, and flow behavior can improve the effective utilization and design of methods to increase the recovery of oil and gas from petroleum reservoirs. The dynamics of fluid flow and trapping phenomena in porous media was investigated. Miscible and immiscible displacement experiments in heterogeneous Berea and Shannon sandstone samples were monitored using X-ray computed tomography (CT scanning) to determine the effect of heterogeneities on fluid flow and trapping. The statistical analysis of pore and pore throat sizes in thin sections cut from these sandstone samples enabled the delineation of small-scale spatial distributions of porosity and permeability. Multiphase displacement experiments were conducted with micromodels constructed using thin slabs of the sandstones. The combination of the CT scanning, thin section, and micromodel techniques enables the investigation of how variations in pore characteristics influence fluid front advancement, fluid distributions, and fluid trapping. Plugs cut from the sandstone samples were investigated using high resolution nuclear magnetic resonance imaging permitting the visualization of oil, water or both within individual pores. The application of these insights will aid in the proper interpretation of relative permeability, capillary pressure, and electrical resistivity data obtained from whole core studies. 7 refs., 14 figs., 2 tabs.

  16. Comparison of infrared and 3D digital image correlation techniques applied for mechanical testing of materials

    Science.gov (United States)

    Krstulović-Opara, Lovre; Surjak, Martin; Vesenjak, Matej; Tonković, Zdenko; Kodvanj, Janoš; Domazet, Željko

    2015-11-01

    To investigate the applicability of infrared thermography as a tool for acquiring dynamic yielding in metals, a comparison of infrared thermography with three dimensional digital image correlation has been made. Dynamical tension tests and three point bending tests of aluminum alloys have been performed to evaluate results obtained by IR thermography in order to detect capabilities and limits for these two methods. Both approaches detect pastification zone migrations during the yielding process. The results of the tension test and three point bending test proved the validity of the IR approach as a method for evaluating the dynamic yielding process when used on complex structures such as cellular porous materials. The stability of the yielding process in the three point bending test, as contrary to the fluctuation of the plastification front in the tension test, is of great importance for the validation of numerical constitutive models. The research proved strong performance, robustness and reliability of the IR approach when used to evaluate yielding during dynamic loading processes, while the 3D DIC method proved to be superior in the low velocity loading regimes. This research based on two basic tests, proved the conclusions and suggestions presented in our previous research on porous materials where middle wave infrared thermography was applied.

  17. Experimental design technique applied to the validation of an instrumental Neutron Activation Analysis procedure

    International Nuclear Information System (INIS)

    Santos, Uanda Paula de M. dos; Moreira, Edson Gonçalves

    2017-01-01

    In this study optimization of procedures and standardization of Instrumental Neutron Activation Analysis (INAA) method were carried out for the determination of the elements bromine, chlorine, magnesium, manganese, potassium, sodium and vanadium in biological matrix materials using short irradiations at a pneumatic system. 2 k experimental designs were applied for evaluation of the individual contribution of selected variables of the analytical procedure in the final mass fraction result. The chosen experimental designs were the 2 3 and the 2 4 , depending on the radionuclide half life. Different certified reference materials and multi-element comparators were analyzed considering the following variables: sample decay time, irradiation time, counting time and sample distance to detector. Comparator concentration, sample mass and irradiation time were maintained constant in this procedure. By means of the statistical analysis and theoretical and experimental considerations, it was determined the optimized experimental conditions for the analytical methods that will be adopted for the validation procedure of INAA methods in the Neutron Activation Analysis Laboratory (LAN) of the Research Reactor Center (CRPq) at the Nuclear and Energy Research Institute (IPEN /CNEN-SP). Optimized conditions were estimated based on the results of z-score tests, main effect, interaction effects and better irradiation conditions. (author)

  18. Impurity Correction Techniques Applied to Existing Doping Measurements of Impurities in Zinc

    Science.gov (United States)

    Pearce, J. V.; Sun, J. P.; Zhang, J. T.; Deng, X. L.

    2017-01-01

    Impurities represent the most significant source of uncertainty in most metal fixed points used for the realization of the International Temperature Scale of 1990 (ITS-90). There are a number of different methods for quantifying the effect of impurities on the freezing temperature of ITS-90 fixed points, many of which rely on an accurate knowledge of the liquidus slope in the limit of low concentration. A key method of determining the liquidus slope is to measure the freezing temperature of a fixed-point material as it is progressively doped with a known amount of impurity. Recently, a series of measurements of the freezing and melting temperature of `slim' Zn fixed-point cells doped with Ag, Fe, Ni, and Pb were presented. Here, additional measurements of the Zn-X system are presented using Ga as a dopant, and the data (Zn-Ag, Zn-Fe, Zn-Ni, Zn-Pb, and Zn-Ga) have been re-analyzed to demonstrate the use of a fitting method based on Scheil solidification which is applied to both melting and freezing curves. In addition, the utility of the Sum of Individual Estimates method is explored with these systems in the context of a recently enhanced database of liquidus slopes of impurities in Zn in the limit of low concentration.

  19. Linear and Non-Linear Control Techniques Applied to Actively Lubricated Journal Bearings

    DEFF Research Database (Denmark)

    Nicoletti, Rodrigo; Santos, Ilmar

    2003-01-01

    The main objectives of actively lubricated bearings are the simultaneous reduction of wear and vibration between rotating and stationary machinery parts. For reducing wear and dissipating vibration energy until certain limits, one can count with the conventional hydrodynamic lubrication. For furt......The main objectives of actively lubricated bearings are the simultaneous reduction of wear and vibration between rotating and stationary machinery parts. For reducing wear and dissipating vibration energy until certain limits, one can count with the conventional hydrodynamic lubrication....... For further reduction of shaft vibrations one can count with the active lubrication action, which is based on injecting pressurised oil into the bearing gap through orifices machined in the bearing sliding surface. The design and efficiency of some linear (PD, PI and PID) and non-linear controllers, applied...... vibration reduction of unbalance response of a rigid rotor, where the PD and the non-linear P controllers show better performance for the frequency range of study (0 to 80 Hz). The feasibility of eliminating rotor-bearing instabilities (phenomena of whirl) by using active lubrication is also investigated...

  20. Experimental design technique applied to the validation of an instrumental Neutron Activation Analysis procedure

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Uanda Paula de M. dos; Moreira, Edson Gonçalves, E-mail: uandapaula@gmail.com, E-mail: emoreira@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

    2017-07-01

    In this study optimization of procedures and standardization of Instrumental Neutron Activation Analysis (INAA) method were carried out for the determination of the elements bromine, chlorine, magnesium, manganese, potassium, sodium and vanadium in biological matrix materials using short irradiations at a pneumatic system. 2{sup k} experimental designs were applied for evaluation of the individual contribution of selected variables of the analytical procedure in the final mass fraction result. The chosen experimental designs were the 2{sup 3} and the 2{sup 4}, depending on the radionuclide half life. Different certified reference materials and multi-element comparators were analyzed considering the following variables: sample decay time, irradiation time, counting time and sample distance to detector. Comparator concentration, sample mass and irradiation time were maintained constant in this procedure. By means of the statistical analysis and theoretical and experimental considerations, it was determined the optimized experimental conditions for the analytical methods that will be adopted for the validation procedure of INAA methods in the Neutron Activation Analysis Laboratory (LAN) of the Research Reactor Center (CRPq) at the Nuclear and Energy Research Institute (IPEN /CNEN-SP). Optimized conditions were estimated based on the results of z-score tests, main effect, interaction effects and better irradiation conditions. (author)

  1. The effectiveness of mobilisation with movement for chronic medial ankle pain: a case study

    Directory of Open Access Journals (Sweden)

    M. Penso

    2008-01-01

    Full Text Available Introduction and Purpose: It has been shown that approximatelythirty percent of those sustaining an ankle sprain are likely to develop chronicfunctional limitations. Mulligan has developed mobilisation with movement (MWMfor treatment of joint dysfunction and suggests that it is a positional fault of the jointthat causes pain and movement restriction. Method: This single case reports on the effects of a MWM technique on chronicmedial ankle pain. The patient was a 25-year-old female runner who had experiencedpain since an initial ankle sprain at 8 years of age. The main findings of the subjective and physical examinations were decrease in active and passive dorsiflexion and eversion range of motion (ROM, shortening of gastrocnemiusand soleus muscles and the functional limitation of pain when running. The patient was treated twice with the MWMtechnique.Results: Outcomes of immediate reduction in pain, restoration of full dorsiflexion and eversion ROM, increase in calfmuscle length and pain free running were observed. This was maintained over a four-month follow up period.Conclusion: This case concurs with previous studies detailing increases in range of motion and restoration of painfree movement as well as adding new support for the resolution of chronic pain with MWM.

  2. Applying industrial process improvement techniques to increase efficiency in a surgical practice.

    Science.gov (United States)

    Reznick, David; Niazov, Lora; Holizna, Eric; Siperstein, Allan

    2014-10-01

    The goal of this study was to examine how industrial process improvement techniques could help streamline the preoperative workup. Lean process improvement was used to streamline patient workup at an endocrine surgery service at a tertiary medical center utilizing multidisciplinary collaboration. The program consisted of several major changes in how patients are processed in the department. The goal was to shorten the wait time between initial call and consult visit and between consult and surgery. We enrolled 1,438 patients enrolled in the program. The wait time from the initial call until consult was reduced from 18.3 ± 0.7 to 15.4 ± 0.9 days. Wait time from consult until operation was reduced from 39.9 ± 1.5 to 33.9 ± 1.3 days for the overall practice and to 15.0 ± 4.8 days for low-risk patients. Patient cancellations were reduced from 27.9 ± 2.4% to 17.3 ± 2.5%. Overall patient flow increased from 30.9 ± 5.1 to 52.4 ± 5.8 consults per month (all P process improvement methodology, surgery patients can benefit from an improved, streamlined process with significant reduction in wait time from call to initial consult and initial consult to surgery, with reduced cancellations. This generalized process has resulted in increased practice throughput and efficiency and is applicable to any surgery practice. Copyright © 2014 Elsevier Inc. All rights reserved.

  3. Anticorrosive coating of SixOyCz on metallic substrates applied with the plasma CVD technique

    International Nuclear Information System (INIS)

    Perillo, P; Lasorsa, C; Versaci, R

    2006-01-01

    This work deals with the production of anticorrosive coatings of Si x O y C z on metallic substrates by PECVD (Plasma Enhanced Chemical Vapor Deposition) in a two layer coating, with a gaseous mixture using methyltrimethoxysilane (Z6070) with the contribution of O 2 and methane as reactive gases. The process involves two steps, the first with the substrate thermalized to 500 o C and the second step with the substrate at room temperature. In the first step the process is carried out with the mixture of O 2 and Z6070, in the second step methane is added to the mixture of the plasma forming gases. The coatings were carried out on AISI 410 stainless steel, AISI M2 steel, titanium and AA6061 aluminum substrates. This work presents the preliminary results of the electrochemical evaluation and the mechanical properties of the coating. Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS/ESCA ), and scanning electron microscopy were used for this study. Electrochemical techniques were used to study the reaction to the corrosion of the coatings. Potentiodynamic polarization curves were prepared in a solution of 5% H 2 SO 4 and in NaCl 0,1M. The tests were undertaken at room temperature. This process is presented as an alternative to the conventional immersion processes by the sol-gel method, which produces the polymerization of the reagent as a result of the effect of the oxygen from the environment, while the plasma process produces very different chemical reactions in the center of the plasma itself with coatings also different (CW)

  4. Applying physiological principles and assessment techniques to swimming the English Channel. A case study.

    Science.gov (United States)

    Acevedo, E O; Meyers, M C; Hayman, M; Haskin, J

    1997-03-01

    This study presents the use of physiological principles and assessment techniques in addressing four objectives that can enhance a swimmer's likelihood of successfully swimming the English Channel. The four objective were: (1) to prescribe training intensities and determine ideal swimming pace; (2) to determine the amount of insulation needed, relative to heat produced, to diminish the likelihood of the swimmer suffering from hypothermia; (3) to calculate the caloric expenditure for the swim and the necessary glucose replacement required to prevent glycogen depletion; and (4) to determine the rate of acclimatization to cold water (15.56 C/60 F). The subject participated in several pool swimming data collection sessions including a tethered swim incremental protocol to determine peak oxygen consumption and onset of lactate accumulation and several steady state swims to determine ideal swimming pace at 4.0 mM/L of lactate. Additionally, these swims provided information on oxygen consumption, which in combination with ultrasound assessment of subcutaneous fat was used to assess heat production and insulation capabilities. Finally, the subject participated in 18 cold water immersions to document acclimatization rate. The data demonstrated the high fitness level of this subject and indicated that at a stroke rate of 63 stokes/min, HR was 130 heats/min and lactate was 4 mM/L. At this swimming pace the swimmer would need to consume 470 kcal of glucose/hr. In addition, the energy produced at this swim pace was 13.25 kcal/min while the energy lost at the present subcutaneous fat quantity was 13.40 kcal/min, requiring a fat weight gain of 6,363.03 g (13.88 lbs) to resist heat loss. Finally, the data from the cold water immersions suggested that acclimatization occurred following two weeks of immersions. There results were provided to the swimmer and utilized in making decisions in preparation for the swim.

  5. Applying Geospatial Techniques to Investigate Boundary Layer Land-Atmosphere Interactions Involved in Tornadogensis

    Science.gov (United States)

    Weigel, A. M.; Griffin, R.; Knupp, K. R.; Molthan, A.; Coleman, T.

    2017-12-01

    Northern Alabama is among the most tornado-prone regions in the United States. This region has a higher degree of spatial variability in both terrain and land cover than the more frequently studied North American Great Plains region due to its proximity to the southern Appalachian Mountains and Cumberland Plateau. More research is needed to understand North Alabama's high tornado frequency and how land surface heterogeneity influences tornadogenesis in the boundary layer. Several modeling and simulation studies stretching back to the 1970's have found that variations in the land surface induce tornadic-like flow near the surface, illustrating a need for further investigation. This presentation introduces research investigating the hypothesis that horizontal gradients in land surface roughness, normal to the direction of flow in the boundary layer, induce vertically oriented vorticity at the surface that can potentially aid in tornadogenesis. A novel approach was implemented to test this hypothesis using a GIS-based quadrant pattern analysis method. This method was developed to quantify spatial relationships and patterns between horizontal variations in land surface roughness and locations of tornadogenesis. Land surface roughness was modeled using the Noah land surface model parameterization scheme which, was applied to MODIS 500 m and Landsat 30 m data in order to compare the relationship between tornadogenesis locations and roughness gradients at different spatial scales. This analysis found a statistical relationship between areas of higher roughness located normal to flow surrounding tornadogenesis locations that supports the tested hypothesis. In this presentation, the innovative use of satellite remote sensing data and GIS technologies to address interactions between the land and atmosphere will be highlighted.

  6. APPLIED PHYTO-REMEDIATION TECHNIQUES USING HALOPHYTES FOR OIL AND BRINE SPILL SCARS

    Energy Technology Data Exchange (ETDEWEB)

    M.L. Korphage; Bruce G. Langhus; Scott Campbell

    2003-03-01

    Produced salt water from historical oil and gas production was often managed with inadequate care and unfortunate consequences. In Kansas, the production practices in the 1930's and 1940's--before statewide anti-pollution laws--were such that fluids were often produced to surface impoundments where the oil would segregate from the salt water. The oil was pumped off the pits and the salt water was able to infiltrate into the subsurface soil zones and underlying bedrock. Over the years, oil producing practices were changed so that segregation of fluids was accomplished in steel tanks and salt water was isolated from the natural environment. But before that could happen, significant areas of the state were scarred by salt water. These areas are now in need of economical remediation. Remediation of salt scarred land can be facilitated with soil amendments, land management, and selection of appropriate salt tolerant plants. Current research on the salt scars around the old Leon Waterflood, in Butler County, Kansas show the relative efficiency of remediation options. Based upon these research findings, it is possible to recommend cost efficient remediation techniques for slight, medium, and heavy salt water damaged soil. Slight salt damage includes soils with Electrical Conductivity (EC) values of 4.0 mS/cm or less. Operators can treat these soils with sufficient amounts of gypsum, install irrigation systems, and till the soil. Appropriate plants can be introduced via transplants or seeded. Medium salt damage includes soils with EC values between 4.0 and 16 mS/cm. Operators will add amendments of gypsum, till the soil, and arrange for irrigation. Some particularly salt tolerant plants can be added but most planting ought to be reserved until the second season of remediation. Severe salt damage includes soil with EC values in excess of 16 mS/cm. Operators will add at least part of the gypsum required, till the soil, and arrange for irrigation. The following

  7. Performance Values for Non-Destructive Assay (NDA) Technique Applied to Wastes: Evaluation by the ESARDA NDA Working Group

    International Nuclear Information System (INIS)

    Rackham, Jamie; Weber, Anne-Laure; Chard, Patrick

    2012-01-01

    The first evaluation of NDA performance values was undertaken by the ESARDA Working Group for Standards and Non Destructive Assay Techniques and was published in 1993. Almost ten years later in 2002 the Working Group reviewed those values and reported on improvements in performance values and new measurement techniques that had emerged since the original assessment. The 2002 evaluation of NDA performance values did not include waste measurements (although these had been incorporated into the 1993 exercise), because although the same measurement techniques are generally applied, the performance is significantly different compared to the assay of conventional Safeguarded special nuclear material. It was therefore considered more appropriate to perform a separate evaluation of performance values for waste assay. Waste assay is becoming increasingly important within the Safeguards community, particularly since the implementation of the Additional Protocol, which calls for declaration of plutonium and HEU bearing waste in addition to information on existing declared material or facilities. Improvements in the measurement performance in recent years, in particular the accuracy, mean that special nuclear materials can now be accounted for in wastes with greater certainty. This paper presents an evaluation of performance values for the NDA techniques in common usage for the assay of waste containing special nuclear material. The main topics covered by the document are: 1- Techniques for plutonium bearing solid wastes 2- Techniques for uranium bearing solid wastes 3 - Techniques for assay of fissile material in spent fuel wastes. Originally it was intended to include performance values for measurements of uranium and plutonium in liquid wastes; however, as no performance data for liquid waste measurements was obtained it was decided to exclude liquid wastes from this report. This issue of the performance values for waste assay has been evaluated and discussed by the ESARDA

  8. Performance Values for Non-Destructive Assay (NDA) Technique Applied to Wastes: Evaluation by the ESARDA NDA Working Group

    Energy Technology Data Exchange (ETDEWEB)

    Rackham, Jamie [Babcock International Group, Sellafield, Seascale, Cumbria, (United Kingdom); Weber, Anne-Laure [Institut de Radioprotection et de Surete Nucleaire Fontenay-Aux-Roses (France); Chard, Patrick [Canberra, Forss Business and Technology park, Thurso, Caithness (United Kingdom)

    2012-12-15

    The first evaluation of NDA performance values was undertaken by the ESARDA Working Group for Standards and Non Destructive Assay Techniques and was published in 1993. Almost ten years later in 2002 the Working Group reviewed those values and reported on improvements in performance values and new measurement techniques that had emerged since the original assessment. The 2002 evaluation of NDA performance values did not include waste measurements (although these had been incorporated into the 1993 exercise), because although the same measurement techniques are generally applied, the performance is significantly different compared to the assay of conventional Safeguarded special nuclear material. It was therefore considered more appropriate to perform a separate evaluation of performance values for waste assay. Waste assay is becoming increasingly important within the Safeguards community, particularly since the implementation of the Additional Protocol, which calls for declaration of plutonium and HEU bearing waste in addition to information on existing declared material or facilities. Improvements in the measurement performance in recent years, in particular the accuracy, mean that special nuclear materials can now be accounted for in wastes with greater certainty. This paper presents an evaluation of performance values for the NDA techniques in common usage for the assay of waste containing special nuclear material. The main topics covered by the document are: 1- Techniques for plutonium bearing solid wastes 2- Techniques for uranium bearing solid wastes 3 - Techniques for assay of fissile material in spent fuel wastes. Originally it was intended to include performance values for measurements of uranium and plutonium in liquid wastes; however, as no performance data for liquid waste measurements was obtained it was decided to exclude liquid wastes from this report. This issue of the performance values for waste assay has been evaluated and discussed by the ESARDA

  9. GORE PRECLUDE MVP dura substitute applied as a nonwatertight "underlay" graft for craniotomies: product and technique evaluation.

    Science.gov (United States)

    Chappell, E Thomas; Pare, Laura; Salehpour, Mohammed; Mathews, Marlon; Middlehof, Charles

    2009-01-01

    While watertight closure of the dura is a long-standing tenet of cranial surgery, it is often not possible and sometimes unnecessary. Many graft materials with various attributes and drawbacks have been in use for many years. A novel synthetic dural graft material called GORE PRECLUDE MVP dura substitute (WL Gore & Associates, Inc, Flagstaff, Ariz) (henceforth called "MVP") is designed for use both in traditional watertight dural closure and as a dural "underlay" graft in a nonwatertight fashion. One surface of MVP is engineered to facilitate fibroblast in-growth so that its proximity to the underside of the dura will lead to rapid incorporation, whereas the other surface acts as a barrier to reduce tissue adhesion to the device. A series of 59 human subjects undergoing craniotomy and available for clinical and radiographic follow-up underwent nonwatertight underlay grafting of their durotomy with MVP. This is an assessment of the specific product and technique. No attempt is made to compare this to other products or techniques. The mean follow-up in this group was more than 4 months. All subjects have ultimately experienced excellent outcomes related to use of the graft implanted with the underlay technique. No complications occurred related directly to MVP, but the wound-related complication rate attributed to the underlay technique was higher than expected (17%). However, careful analysis found a high rate of risk factors for wound complications and determined that complications with the underlay technique could be avoided by assuring close approximation of the graft material to the underside of the dura. MVP can be used as an underlay graft in a nonwatertight fashion. However, if used over large voids (relaxed brain or large tumor bed), "tacking" or traditional watertight closure techniques should be used. The underlay application of MVP is best applied over the convexities and is particularly well-suited to duraplasty after hemicraniectomy.

  10. Zero order and signal processing spectrophotometric techniques applied for resolving interference of metronidazole with ciprofloxacin in their pharmaceutical dosage form.

    Science.gov (United States)

    Attia, Khalid A M; Nassar, Mohammed W I; El-Zeiny, Mohamed B; Serag, Ahmed

    2016-02-05

    Four rapid, simple, accurate and precise spectrophotometric methods were used for the determination of ciprofloxacin in the presence of metronidazole as interference. The methods under study are area under the curve, simultaneous equation in addition to smart signal processing techniques of manipulating ratio spectra namely Savitsky-Golay filters and continuous wavelet transform. All the methods were validated according to the ICH guidelines where accuracy, precision and repeatability were found to be within the acceptable limits. The selectivity of the proposed methods was tested using laboratory prepared mixtures and assessed by applying the standard addition technique. So, they can therefore be used for the routine analysis of ciprofloxacin in quality-control laboratories. Copyright © 2015 Elsevier B.V. All rights reserved.

  11. Non-destructive electrochemical techniques applied to the corrosion evaluation of the liner structures in nuclear power plants

    International Nuclear Information System (INIS)

    Martinez, I.; Castillo, A.; Andrade, C.

    2008-01-01

    The liner structure in nuclear power plants provides containment for the operation and therefore the study of its durability and integrity during its service life is an important issue. There are several causes for the deterioration of the liner, which in general involve corrosion due to its metallic nature. The present paper is aimed at describing the assessment of corrosion problems of two liners from two different nuclear power plants, which were evaluated using non-destructive electrochemical techniques. In spite of the testing difficulties arisen, from the results extracted it can be concluded that the electrochemical techniques applied are adequate for the corrosion evaluation. They provide important information about the integrity of the structure and allow for its evolution with time to be assessed

  12. Applying modern psychometric techniques to melodic discrimination testing: Item response theory, computerised adaptive testing, and automatic item generation.

    Science.gov (United States)

    Harrison, Peter M C; Collins, Tom; Müllensiefen, Daniel

    2017-06-15

    Modern psychometric theory provides many useful tools for ability testing, such as item response theory, computerised adaptive testing, and automatic item generation. However, these techniques have yet to be integrated into mainstream psychological practice. This is unfortunate, because modern psychometric techniques can bring many benefits, including sophisticated reliability measures, improved construct validity, avoidance of exposure effects, and improved efficiency. In the present research we therefore use these techniques to develop a new test of a well-studied psychological capacity: melodic discrimination, the ability to detect differences between melodies. We calibrate and validate this test in a series of studies. Studies 1 and 2 respectively calibrate and validate an initial test version, while Studies 3 and 4 calibrate and validate an updated test version incorporating additional easy items. The results support the new test's viability, with evidence for strong reliability and construct validity. We discuss how these modern psychometric techniques may also be profitably applied to other areas of music psychology and psychological science in general.

  13. Surfactant-induced mobilisation of trace metals from estuarine sediment: Implications for contaminant bioaccessibility and remediation

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Anu [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Turner, Andrew [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)], E-mail: aturner@plymouth.ac.uk

    2009-02-15

    The mobilisation of metals (Al, Fe, Cd, Cu, Mn, Ni, Pb, Sn, Zn) from contaminated estuarine sediment has been examined using commercially available surfactants. Metal release by the anionic surfactant, sodium dodecyl sulphate (SDS), increased with increasing amphiphile concentration up to and above its critical micelle concentration (CMC). Metal mobilisation by the bile acid salt, sodium taurocholate, and the nonionic surfactant, Triton X-100, however, did not vary with amphiphile concentration. SDS was the most efficient surfactant in mobilising metals from the sample, and Cd, Cu and Ni were released to the greatest extents (12-18% of total metal at [SDS] > CMC). Metal mobilisation appeared to proceed via complexation with anionic amphiphiles and denudation of hydrophobic host phases. Surfactants may play an important role in the solubilisation of metals in the digestive environment of deposit-feeding animals and, potentially, in the remediation of metal-contaminated soil and sediment. - Significant quantities of metals are mobilised from estuarine sediment by commercially available surfactants.

  14. Émeutes urbaines, sentiments d’injustice, mobilisations associatives

    Directory of Open Access Journals (Sweden)

    Éric Marlière

    2011-07-01

    Full Text Available Cet article a pour objectif l’appréhension des répertoires de mobilisations politiques des jeunes dits « des cités ». Pour cela, il faut nous intéresser aux modes de vie de ces jeunes structurés depuis plus de trente ans maintenant autour du chômage et de la précarité et des nouvelles formes de ségrégation. Cette situation engendre chez les jeunes une certaine frustration sociale se manifestant sous la forme d’un sentiment d’injustice plus ou moins diffus. Si les émeutes urbaines constituent le mode d’action le plus médiatique, un certain nombre de jeunes adultes originaires « des cités » réagissent à travers un ensemble d’initiatives associatives nationales et locales comme le montrent les dernières échéances électorales.Urban riots, feeling of injustice and associative mobilizationsThis article’s objective are the understanding of the directories of the political youth called “cities”. For this, we must concern ourselves with life’s styles of the young people structured over 30 years now about unemployment and job insecurity and new forms of segregation. This creates youth frustration manifested as a feeling of injustice more or less diffuse. If the urban riots of action in the most media, a number of young adults from the “cities” are responding through a number of national associations and local initiatives as evidenced by the recent elections.Revueltas urbanas, sentimientos de injusticia, formas asociativasEste artículo tiene como objetivo el aprehender las diferentes formas de las movilizaciones políticas de los jóvenes de los barrios desfavorecidos. Para cumplirlo es necesario que nos interesemos por las maneras de vivir de esos jóvenes cuyas vidas se desarrollan dentro del paro, la precariedad y nuevas formas de segregación. Esta situación engendra una gran frustración social con conciencia más o menos difusa de ser víctimas de injusticias. Si las revueltas urbanas constituyen la

  15. Applying a nonlinear, pitch-catch, ultrasonic technique for the detection of kissing bonds in friction stir welds.

    Science.gov (United States)

    Delrue, Steven; Tabatabaeipour, Morteza; Hettler, Jan; Van Den Abeele, Koen

    2016-05-01

    Friction stir welding (FSW) is a promising technology for the joining of aluminum alloys and other metallic admixtures that are hard to weld by conventional fusion welding. Although FSW generally provides better fatigue properties than traditional fusion welding methods, fatigue properties are still significantly lower than for the base material. Apart from voids, kissing bonds for instance, in the form of closed cracks propagating along the interface of the stirred and heat affected zone, are inherent features of the weld and can be considered as one of the main causes of a reduced fatigue life of FSW in comparison to the base material. The main problem with kissing bond defects in FSW, is that they currently are very difficult to detect using existing NDT methods. Besides, in most cases, the defects are not directly accessible from the exposed surface. Therefore, new techniques capable of detecting small kissing bond flaws need to be introduced. In the present paper, a novel and practical approach is introduced based on a nonlinear, single-sided, ultrasonic technique. The proposed inspection technique uses two single element transducers, with the first transducer transmitting an ultrasonic signal that focuses the ultrasonic waves at the bottom side of the sample where cracks are most likely to occur. The large amount of energy at the focus activates the kissing bond, resulting in the generation of nonlinear features in the wave propagation. These nonlinear features are then captured by the second transducer operating in pitch-catch mode, and are analyzed, using pulse inversion, to reveal the presence of a defect. The performance of the proposed nonlinear, pitch-catch technique, is first illustrated using a numerical study of an aluminum sample containing simple, vertically oriented, incipient cracks. Later, the proposed technique is also applied experimentally on a real-life friction stir welded butt joint containing a kissing bond flaw. Copyright © 2016

  16. Beyond Astro 101: A First Report on Applying Interactive Education Techniques to an Astronphysics Class for Majors

    Science.gov (United States)

    Perrin, Marshall D.; Ghez, A. M.

    2009-05-01

    Learner-centered interactive instruction methods now have a proven track record in improving learning in "Astro 101" courses for non-majors, but have rarely been applied to higher-level astronomy courses. Can we hope for similar gains in classes aimed at astrophysics majors, or is the subject matter too fundamentally different for those techniques to apply? We present here an initial report on an updated calculus-based Introduction to Astrophysics class at UCLA that suggests such techniques can indeed result in increased learning for major students. We augmented the traditional blackboard-derivation lectures and challenging weekly problem sets by adding online questions on pre-reading assignments (''just-in-time teaching'') and frequent multiple-choice questions in class ("Think-Pair-Share''). We describe our approach, and present examples of the new Think-Pair-Share questions developed for this more sophisticated material. Our informal observations after one term are that with this approach, students are more engaged and alert, and score higher on exams than typical in previous years. This is anecdotal evidence, not hard data yet, and there is clearly a vast amount of work to be done in this area. But our first impressions strongly encourage us that interactive methods should be able improve the astrophysics major just as they have improved Astro 101.

  17. 2D and 3D optical diagnostic techniques applied to Madonna dei Fusi by Leonardo da Vinci

    Science.gov (United States)

    Fontana, R.; Gambino, M. C.; Greco, M.; Marras, L.; Materazzi, M.; Pampaloni, E.; Pelagotti, A.; Pezzati, L.; Poggi, P.; Sanapo, C.

    2005-06-01

    3D measurement and modelling have been traditionally applied to statues, buildings, archeological sites or similar large structures, but rarely to paintings. Recently, however, 3D measurements have been performed successfully also on easel paintings, allowing to detect and document the painting's surface. We used 3D models to integrate the results of various 2D imaging techniques on a common reference frame. These applications show how the 3D shape information, complemented with 2D colour maps as well as with other types of sensory data, provide the most interesting information. The 3D data acquisition was carried out by means of two devices: a high-resolution laser micro-profilometer, composed of a commercial distance meter mounted on a scanning device, and a laser-line scanner. The 2D data acquisitions were carried out using a scanning device for simultaneous RGB colour imaging and IR reflectography, and a UV fluorescence multispectral image acquisition system. We present here the results of the techniques described, applied to the analysis of an important painting of the Italian Reinassance: `Madonna dei Fusi', attributed to Leonardo da Vinci.

  18. Convalescence and hospital stay after colonic surgery with balanced analgesia, early oral feeding, and enforced mobilisation

    DEFF Research Database (Denmark)

    Møiniche, S; Bülow, Steffen; Hesselfeldt, Peter

    1995-01-01

    OBJECTIVE: To evaluate the combined effects of pain relief by continuous epidural analgesia, early oral feeding and enforced mobilisation on convalescence and hospital stay after colonic resection. DESIGN: Uncontrolled pilot investigation. SETTING: University hospital, Denmark. SUBJECTS: 17...... unselected patients (median age 69 years) undergoing colonic resection. INTERVENTIONS: Patients received combined epidural and general anaesthesia during operations and after operation were given continuous epidural bupivacaine 0.25%, 4 ml hour and morphine 0.2 mg hour, for 96 hours and oral paracetamol 4 g....../daily. No patient had a nasogastric tube, and oral feeding with normal food and protein enriched solutions (1000 Kcal (4180 KJ/day) was instituted 24 hours postoperatively together with intensive mobilisation. RESULTS: Median visual analogue pain scores were zero at rest and minimal during coughing and mobilisation...

  19. Applied research on air pollution using nuclear-related analytical techniques. Report on the second research co-ordination meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    A co-ordinated research programme (CRP) on applied research on air pollution using nuclear-related techniques is a global CRP which started in 1992, and is scheduled to run until early 1997. The purpose of this CRP is to promote the use of nuclear analytical techniques in air pollution studies, e.g. NAA, XRF, and PIXE for the analysis of toxic and other trace elements in air particulate matter. The main purposes of the core programme are i) to support the use of nuclear and nuclear-related analytical techniques for research and monitoring studies on air pollution, ii) to identify major sources of air pollution affecting each of the participating countries with particular reference to toxic heavy metals, and iii) to obtain comparative data on pollution levels in areas of high pollution (e.g. a city centre or a populated area downwind of a large pollution source) and low pollution (e.g. rural area). This document reports the discussions held during the second Research Co-ordination Meeting (RCM) for the CRP which took place at ANSTO in Menai, Australia. (author)

  20. Applied research on air pollution using nuclear-related analytical techniques. Report on the second research co-ordination meeting

    International Nuclear Information System (INIS)

    1995-01-01

    A co-ordinated research programme (CRP) on applied research on air pollution using nuclear-related techniques is a global CRP which started in 1992, and is scheduled to run until early 1997. The purpose of this CRP is to promote the use of nuclear analytical techniques in air pollution studies, e.g. NAA, XRF, and PIXE for the analysis of toxic and other trace elements in air particulate matter. The main purposes of the core programme are i) to support the use of nuclear and nuclear-related analytical techniques for research and monitoring studies on air pollution, ii) to identify major sources of air pollution affecting each of the participating countries with particular reference to toxic heavy metals, and iii) to obtain comparative data on pollution levels in areas of high pollution (e.g. a city centre or a populated area downwind of a large pollution source) and low pollution (e.g. rural area). This document reports the discussions held during the second Research Co-ordination Meeting (RCM) for the CRP which took place at ANSTO in Menai, Australia. (author)

  1. Estimates of error introduced when one-dimensional inverse heat transfer techniques are applied to multi-dimensional problems

    International Nuclear Information System (INIS)

    Lopez, C.; Koski, J.A.; Razani, A.

    2000-01-01

    A study of the errors introduced when one-dimensional inverse heat conduction techniques are applied to problems involving two-dimensional heat transfer effects was performed. The geometry used for the study was a cylinder with similar dimensions as a typical container used for the transportation of radioactive materials. The finite element analysis code MSC P/Thermal was used to generate synthetic test data that was then used as input for an inverse heat conduction code. Four different problems were considered including one with uniform flux around the outer surface of the cylinder and three with non-uniform flux applied over 360 deg C, 180 deg C, and 90 deg C sections of the outer surface of the cylinder. The Sandia One-Dimensional Direct and Inverse Thermal (SODDIT) code was used to estimate the surface heat flux of all four cases. The error analysis was performed by comparing the results from SODDIT and the heat flux calculated based on the temperature results obtained from P/Thermal. Results showed an increase in error of the surface heat flux estimates as the applied heat became more localized. For the uniform case, SODDIT provided heat flux estimates with a maximum error of 0.5% whereas for the non-uniform cases, the maximum errors were found to be about 3%, 7%, and 18% for the 360 deg C, 180 deg C, and 90 deg C cases, respectively

  2. Applying CFD in the Analysis of Heavy-Oil Transportation in Curved Pipes Using Core-Flow Technique

    Directory of Open Access Journals (Sweden)

    S Conceição

    2017-06-01

    Full Text Available Multiphase flow of oil, gas and water occurs in the petroleum industry from the reservoir to the processing units. The occurrence of heavy oils in the world is increasing significantly and points to the need for greater investment in the reservoirs exploitation and, consequently, to the development of new technologies for the production and transport of this oil. Therefore, it is interesting improve techniques to ensure an increase in energy efficiency in the transport of this oil. The core-flow technique is one of the most advantageous methods of lifting and transporting of oil. The core-flow technique does not alter the oil viscosity, but change the flow pattern and thus, reducing friction during heavy oil transportation. This flow pattern is characterized by a fine water pellicle that is formed close to the inner wall of the pipe, aging as lubricant of the oil flowing in the core of the pipe. In this sense, the objective of this paper is to study the isothermal flow of heavy oil in curved pipelines, employing the core-flow technique. A three-dimensional, transient and isothermal mathematical model that considers the mixture and k-e  turbulence models to address the gas-water-heavy oil three-phase flow in the pipe was applied for analysis. Simulations with different flow patterns of the involved phases (oil-gas-water have been done, in order to optimize the transport of heavy oils. Results of pressure and volumetric fraction distribution of the involved phases are presented and analyzed. It was verified that the oil core lubricated by a fine water layer flowing in the pipe considerably decreases pressure drop.

  3. Identifying key factors for mobilising under-utilised low carbon land resources : A case study on Kalimantan

    NARCIS (Netherlands)

    Goh, Chun Sheng; Junginger, Martin; Potter, Lesley; Faaij, André; Wicke, Birka

    2018-01-01

    Mobilising under-utilised low carbon (ULC) land for future agricultural expansion helps minimising further carbon stock loss. This study examined the regency cases in Kalimantan, a carbon loss hotspot, to understand the key factors for mobilising ULC land via narrative interviews with a range of

  4. Tidlig struktureret mobilisering og træning af kritisk syge patienter på et dansk intensivafsnit

    DEFF Research Database (Denmark)

    Astrup Sørensen, Katrine; Hvid, Sidsel; Rolving, Nanna

    2015-01-01

    derimod anvendelig i forhold til at tilpasse niveauet for mobilisering og træning. Relevans for klinisk praksis: Tidlig mobilisering og træning er mulig at indføre med en simpel algoritme, dog med hensyntagen til individuelle screeningskriterier fra sted til sted, da disse åbenbart ikke er nemme...

  5. Early mobilisation versus plaster immobilisation of simple elbow dislocations: Results of the FuncSiE multicentre randomised clinical trial

    NARCIS (Netherlands)

    G.I.T. Iordens (Gijs); E.M.M. van Lieshout (Esther); N.W.L. Schep (Niels); J. de Haan (Jeroen); W.E. Tuinebreijer (Wim); D. Eygendaal (Denise); E.F. van Beeck (Ed); P. Patka (Peter); M.H.J. Verhofstad (Michiel); D. den Hartog (Dennis); R.S. Breederveld (Roelf S.); M.W.G.A. Bronkhorst (Maarten); M.R. de Vries (Mark); B.J. Dwars (Boudewijn); R. Haverlag (Robert); S.A.G. Meylaerts (Sven); J.W. Mulder (Jan-Willem); K.J. Ponsen (Kees-jan); W.H. Roerdink (Herbert); G.R. Roukema (Gert); I.B. Schipper (Inger); M.A. Schouten (Michel); J.B. Sintenie (Jan Bernard); S. Sivro (Senail); J.G.H. van den Brand (Johan); F.M. van der Linden (Frits); H.G.W.M. Meulen (Hub); E.J.M.M. Verleisdonk (Egbert); J.P.A.M. Vroemen (Jos); M. Waleboer (Marco); W.J. Willems (Jaap)

    2017-01-01

    textabstractBackground/aim To compare outcome of early mobilisation and plaster immobilisation in patients with a simple elbow dislocation. We hypothesised that early mobilisation would result in earlier functional recovery. Methods From August 2009 to September 2012, 100 adult patients with a

  6. Geological-geophysical techniques applied to urban planning in karst hazardous areas. Case study of Zaragoza, NE Spain

    Science.gov (United States)

    Pueyo Anchuela, O.; Soriano, A.; Casas Sainz, A.; Pocoví Juan, A.

    2009-12-01

    Industrial and urban growth must deal in some settings with geological hazards. In the last 50 years, the city of Zaragoza (NE Spain) has developed an increase of its urbanized area in a progression several orders higher than expected from its population increase. This fast growth has affected several areas around the city that were not usually used for construction. Maps of the Zaragoza city area at the end of the XIXth century and beginning of the XXth reveal the presence of karst hazards in several zones that can be observed in more modern data, as aerial photographs taken during a period ranging from 1927 to present. The urban and industrial development has covered many of these hazardous zones, even though potential risks were known. The origins of the karst problems are related to the solution of evaporites (mainly gypsum, glauberite and halite) that represent the Miocene substratum of the Zaragoza area underlying the Quaternary terraces and pediments related to the Ebro River and its tributaries. Historical data show the persistence of subsidence foci during long periods of time while in recent urbanized areas this stability is not shared, observing the increase of activity and/or radius affection in short periods of time after building over. These problems can be related to two factors: i) urban development over hazardous areas can increase the karst activity and ii) the affection radius is not properly established with the commonly applied methods. One way to develop these detailed maps can be related to the geophysical approach. The applied geophysical routine, dependent on the characteristics of the surveyed area, is based on potential geophysical techniques (magnetometry and gravimetry) and others related to the application of induced fields (EM and GPR). The obtained results can be related to more straightforward criteria as the detection of cavities in the subsoil and indirect indicators related to the long-term activity of the subsidence areas

  7. Molecular and cultivation-dependent analysis of metal-reducing bacteria implicated in arsenic mobilisation in south-east asian aquifers

    International Nuclear Information System (INIS)

    Hery, Marina; Gault, Andrew G.; Rowland, Helen A.L.; Lear, Gavin; Polya, David A.; Lloyd, Jonathan R.

    2008-01-01

    The reduction of sorbed As(V) to the potentially more mobile As(III) by As-respiring anaerobic bacteria has been implicated in the mobilisation of the toxic metalloid in aquifer sediments in SE Asia. However, there is currently only a limited amount of information on the identity of the organisms that can respire As(V) in these sediment systems. Here experiments are described that have targeted As(V)-respiring bacteria using cultivation-independent molecular techniques, and also more traditional microbiological approaches that have used growth media highly selective for organisms that can grow using arsenate as the sole electron acceptor supplied for anaerobic growth. The molecular techniques used have initially targeted DNA from microcosms displaying maximal rates of arsenate reduction, both with and without added electron donor. More recent studies from the authors' laboratory have used stable isotope probing techniques, targeting DNA from the active microbial fraction in microcosms labelled with [ 13 C]acetate supplied as an electron donor for arsenate reduction. Phylogenetic analyses using a highly conserved genetic marker (the 16S rRNA gene) have suggested the involvement of Sulfurospirillum and Geobacter species in arsenate-respiration, and this has been supported further by complimentary experiments using more traditional microbiological techniques. Additional research required to clarify the role of these organisms in the mobilisation of As in situ are discussed

  8. Analysis of Arbitrary Reflector Antennas Applying the Geometrical Theory of Diffraction Together with the Master Points Technique

    Directory of Open Access Journals (Sweden)

    María Jesús Algar

    2013-01-01

    Full Text Available An efficient approach for the analysis of surface conformed reflector antennas fed arbitrarily is presented. The near field in a large number of sampling points in the aperture of the reflector is obtained applying the Geometrical Theory of Diffraction (GTD. A new technique named Master Points has been developed to reduce the complexity of the ray-tracing computations. The combination of both GTD and Master Points reduces the time requirements of this kind of analysis. To validate the new approach, several reflectors and the effects on the radiation pattern caused by shifting the feed and introducing different obstacles have been considered concerning both simple and complex geometries. The results of these analyses have been compared with the Method of Moments (MoM results.

  9. 3D laser scanning techniques applying to tunnel documentation and geological mapping at Aespoe hard rock laboratory, Sweden

    International Nuclear Information System (INIS)

    Feng, Q.; Wang, G.; Roeshoff, K.

    2008-01-01

    3D terrestrial laser scanning is nowadays one of the most attractive methods to applying for 3D mapping and documentation of rock faces and tunnels, and shows the most potential to improve the data quality and provide some good solutions in rock engineering projects. In this paper, the state-of-the-art methods are described for different possibility to tunnel documentation and geological mapping based on 3D laser scanning data. Some results are presented from the case study performed at the Hard Rock Laboratory, Aespoe run by SKB, Swedish Nuclear Fuel and Waste Management Co. Comparing to traditional methods, 3D laser scanning techniques can not only provide us with a rapid and 3D digital way for tunnel documentation, but also create a potential chance to achieve high quality data, which might be beneficial to different rock engineering project procedures, including field data acquisition, data processing, data retrieving and management, and also modeling and design. (authors)

  10. Application of the PISC results and methodology to assess the effectiveness of NDT techniques applied on non nuclear components

    International Nuclear Information System (INIS)

    Maciga, G.; Papponetti, M.; Crutzen, S.; Jehenson, P.

    1990-01-01

    Performance demonstration for NDT has been an active topic for several years. Interest in it came to the fore in the early 1980's when several institutions started to propose to use of realistic training assemblies and the formal approach of Validation Centers. These steps were justified for example by the results of the PISC exercises which concluded that there was a need for performance demonstration starting with capability assessment of techniques and procedure as they were routinely applied. If the PISC programme is put under the general ''Nuclear Motivation'', the PISC Methodology could be extended to problems to structural components in general, such as on conventional power plants, chemical, aerospace and offshore industries, where integrity and safety have regarded as being of great importance. Some themes of NDT inspections of fossil power plant and offshore components that could be objects of validation studies will be illustrated. (author)

  11. A Methods and procedures to apply probabilistic safety Assessment (PSA) techniques to the cobalt-therapy process. Cuban experience

    International Nuclear Information System (INIS)

    Vilaragut Llanes, J.J.; Ferro Fernandez, R.; Lozano Lima, B; De la Fuente Puch, A.; Dumenigo Gonzalez, C.; Troncoso Fleitas, M.; Perez Reyes, Y.

    2003-01-01

    This paper presents the results of the Probabilistic Safety Analysis (PSA) to the Cobalt Therapy Process, which was performed as part of the International Atomic Energy Agency's Coordinated Research Project (CRP) to Investigate Appropriate Methods and Procedures to Apply Probabilistic Safety Assessment (PSA) Techniques to Large Radiation Sources. The primary methodological tools used in the analysis were Failure Modes and Effects Analysis (FMEA), Event Trees and Fault Trees. These tools were used to evaluate occupational, public and medical exposures during cobalt therapy treatment. The emphasis of the study was on the radiological protection of patients. During the course of the PSA, several findings were analysed concerning the cobalt treatment process. In relation with the Undesired Events Probabilities, the lowest exposures probabilities correspond to the public exposures during the treatment process (Z21); around 10-10 per year, being the workers exposures (Z11); around 10-4 per year. Regarding to the patient, the Z33 probabilities prevail (not desired dose to normal tissue) and Z34 (not irradiated portion to target volume). Patient accidental exposures are also classified in terms of the extent to which the error is likely to affect individual treatments, individual patients, or all the patients treated on a specific unit. Sensitivity analyses were realised to determine the influence of certain tasks or critical stages on the results. As a conclusion the study establishes that the PSA techniques may effectively and reasonably determine the risk associated to the cobalt-therapy treatment process, though there are some weaknesses in its methodological application for this kind of study requiring further research. These weaknesses are due to the fact that the traditional PSA has been mainly applied to complex hardware systems designed to operate with a high automation level, whilst the cobalt therapy treatment is a relatively simple hardware system with a

  12. Conceptual design study and evaluation of an advanced treatment process applying a submerged combustion technique for spent solvents

    International Nuclear Information System (INIS)

    Uchiyama, Gunzo; Maeda, Mitsuru; Fijine, Sachio; Chida, Mitsuhisa; Kirishima, Kenji.

    1993-10-01

    An advanced treatment process based on a submerged combustion technique was proposed for spent solvents and the distillation residues containing transuranium (TRU) nuclides. A conceptual design study and the preliminary cost estimation of the treatment facility applying the process were conducted. Based on the results of the study, the process evaluation on the technical features, such as safety, volume reduction of TRU waste and economics was carried out. The key requirements for practical use were also summarized. It was shown that the process had the features as follows: the simplified treatment and solidification steps will not generate secondary aqueous wastes, the volume of TRU solid waste will be reduced less than one tenth of that of a reference technique (pyrolysis process), and the facility construction cost is less than 1 % of the total construction cost of a future large scale reprocessing plant. As for the low level wastes of calcium phosphate, it was shown that the further removal of β · γ nuclides with TRU nuclides from the wastes would be required for the safety in interim storage and transportation and for the load of shielding. (author)

  13. Teachers and Learners’ Perceptions of Applying Translation as a Method, Strategy, or Technique in an Iranian EFL Setting

    Directory of Open Access Journals (Sweden)

    Fatemeh Mollaei

    2017-04-01

    Full Text Available It has been found that translation is an efficient means to teach/learn grammar, syntax, and lexis of a foreign language. Meanwhile, translation is good for beginners who do not still enjoy the critical level of proficiency in their target language for expression.  This study was conducted to examine the teachers and learners’ perceptions of employing translation in the foreign language classroom; i.e., the effects, merits, demerits, limitations, as well as its use as a method, strategy or technique. Both quantitative and qualitative methods were used to collect and analyze the data from graduate and undergraduate learners (n=56 and teachers (n=44, male and female, who responded to two questionnaires. Additionally, only the teachers were interviewed to gain richer insight into their perceptions and attitudes. According to the results of independent samples t-test, there was no significant difference between teachers and learners’ attitude to applying translation as a method, strategy, or technique in learning a foreign language.  Based on the interview results, some teachers believed that employing translation in the foreign language context was helpful but not constantly. They claimed that translation was only effective in teaching vocabulary and grammar apart from leaners’ proficiency level as it can clarify meaning. But some other teachers noted that mother tongue would interfere with learning foreign language; they considered translation as a time-consuming activity through which students cannot capture the exact meaning.

  14. Influence of elemental concentration in soil on vegetables applying analytical nuclear techniques: k0-instrumental neutron activation analysis and radiometry

    International Nuclear Information System (INIS)

    Menezes, Maria Angela de B.C.; Mingote, Raquel Maia; Silva, Lucilene Guerra e; Pedrosa, Lorena Gomes

    2005-01-01

    Samples from two vegetable gardens where analysed aiming at determining the elemental concentration. The vegetables selected to be studied are grown by the people for their own use and are present in daily meal. One vegetable garden studied is close to a mining activity in a region inserted in the Iron Quadrangle (Quadrilatero Ferrifero), located in the Brazilian state of Minas Gerais. This region is considered one of the richest mineral bearing regions in the world. Another vegetable garden studied is far from this region and without any mining activity It was also studied as a comparative site. This assessment was carried out to evaluate the elemental concentration in soil and vegetables, matrixes connected with the chain food, applying the k 0 -Instrumental Neutron Activation Analysis (k 0 -INAA) at the Laboratory for Neutron Activation Analysis. However, this work reports only the results of thorium, uranium and rare-earth obtained in samples collected during the dry season, focusing on the influence of these elements on vegetable elemental composition. Results of natural radioactivity determined by Gross Alpha and Gross Beta measurements, are also reported. This study is related to the BRA 11920 project, entitled 'Iron Quadrangle, Brazil: assessment of health impact caused by mining pollutants through chain food applying nuclear and related techniques', one of the researches co-ordinated by the IAEA (Vienna, Austria). (author)

  15. Applying value stream mapping techniques to eliminate non-value-added waste for the procurement of endovascular stents

    International Nuclear Information System (INIS)

    Teichgräber, Ulf K.; Bucourt, Maximilian de

    2012-01-01

    Objectives: To eliminate non-value-adding (NVA) waste for the procurement of endovascular stents in interventional radiology services by applying value stream mapping (VSM). Materials and methods: The Lean manufacturing technique was used to analyze the process of material and information flow currently required to direct endovascular stents from external suppliers to patients. Based on a decision point analysis for the procurement of stents in the hospital, a present state VSM was drawn. After assessment of the current status VSM and progressive elimination of unnecessary NVA waste, a future state VSM was drawn. Results: The current state VSM demonstrated that out of 13 processes for the procurement of stents only 2 processes were value-adding. Out of the NVA processes 5 processes were unnecessary NVA activities, which could be eliminated. The decision point analysis demonstrated that the procurement of stents was mainly a forecast driven push system. The future state VSM applies a pull inventory control system to trigger the movement of a unit after withdrawal by using a consignment stock. Conclusion: VSM is a visualization tool for the supply chain and value stream, based on the Toyota Production System and greatly assists in successfully implementing a Lean system.

  16. Effect of applying wheat stubble on preservation and utilization of n-fertilizer by 15N trace technique

    International Nuclear Information System (INIS)

    Xu Xinyu; Zhang Yumei; Xiang Hua; Hu Jisheng

    1991-10-01

    By using 15 N trace technique, the effect of applying wheat stubble on the preservation and utilization rate of 15 N- ammonium sulphate have been studied. The abundance of ( 15 NH 4 ) 2 SO 4 fertilizer was 8.92%. After three years pot test and field plot test, the results showed that the yields with ' 15 N+mulching' and ' 15 N+incorporating' treated were increased by 5.4∼30.0% for spring wheat and millet(pot test), and 18∼23% for winter wheat and summer corn(field plot test), as compared with only ' 15 N' treatment. The results of 15 N-fertilizer labelled tests showed that the utilization rates of 15 N-fertilizer treated by ' 15 N+mulching' for cropping seasons were 57.8%, 65.8%, 36.6% and 8.5% respectively. These were increased 3.7%, 10.2%, 21.5% and 2.8% as compared with only ' 15 N' treatment. Comparing with only ' 15 N'treatment, the N leached off by percolation water was decreasing 50%, the loss of N caused by volatilization was decreasing 30.3% and the N in humus was increasing 21.1%. All of these proved that the applying of wheat stubble in different mode would adjust and control the activation of microbe in the soil, and the preservation and utilization rate of fertilizer in the soul would be increased

  17. Applying value stream mapping techniques to eliminate non-value-added waste for the procurement of endovascular stents.

    Science.gov (United States)

    Teichgräber, Ulf K; de Bucourt, Maximilian

    2012-01-01

    OJECTIVES: To eliminate non-value-adding (NVA) waste for the procurement of endovascular stents in interventional radiology services by applying value stream mapping (VSM). The Lean manufacturing technique was used to analyze the process of material and information flow currently required to direct endovascular stents from external suppliers to patients. Based on a decision point analysis for the procurement of stents in the hospital, a present state VSM was drawn. After assessment of the current status VSM and progressive elimination of unnecessary NVA waste, a future state VSM was drawn. The current state VSM demonstrated that out of 13 processes for the procurement of stents only 2 processes were value-adding. Out of the NVA processes 5 processes were unnecessary NVA activities, which could be eliminated. The decision point analysis demonstrated that the procurement of stents was mainly a forecast driven push system. The future state VSM applies a pull inventory control system to trigger the movement of a unit after withdrawal by using a consignment stock. VSM is a visualization tool for the supply chain and value stream, based on the Toyota Production System and greatly assists in successfully implementing a Lean system. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

  18. Applying clinically proven human techniques for contraception and fertility to endangered species and zoo animals: a review.

    Science.gov (United States)

    Silber, Sherman J; Barbey, Natalie; Lenahan, Kathy; Silber, David Z

    2013-12-01

    Reversible contraception that does not alter natural behavior is a critical need for managing zoo populations. In addition to reversible contraception, other fertility techniques perfected in humans may be useful, such as in vitro fertilization (IVF) or oocyte and embryo banking for endangered species like amphibians and Mexican wolves (Canis lupus baileyi). Furthermore, the genetics of human fertility can give a better understanding of fertility in more exotic species. Collaborations were established to apply human fertility techniques to the captive population. Reversible vasectomy might be one solution for reversible contraception that does not alter behavior. Reversible approaches to vasectomy, avoiding secondary epididymal disruption, were attempted in South American bush dogs (Speothos venaticus), chimpanzees (Pan troglodytes), gorillas (Gorilla gorilla), Przewalski's horse (Equus przewalski poliakov), and Sika deer (Cervus nippon) in a variety of zoos around the world. These techniques were first perfected in > 4,000 humans before attempting them in zoo animals. In vitro fertilization with gestational surrogacy was used to attempt to break the vicious cycle of hand rearing of purebred orangutans, and egg and ovary vitrification in humans have led to successful gamete banking for Mexican wolves and disappearing amphibians. The study of the human Y chromosome has even explained a mechanism of extinction related to global climate change. The best results with vasectomy reversal (normal sperm counts, pregnancy, and live offspring) were obtained when the original vasectomy was performed "open-ended," so as to avoid pressure-induced epididymal disruption. The attempt at gestational surrogacy for orangutans failed because of severe male infertility and the lack of success with human ovarian hyperstimulation protocols. Vitrification of oocytes is already being employed for the Amphibian Ark Project and for Mexican wolves. Vasectomy can be a reversible contraception

  19. Functional reasoning, explanation and analysis: Part 1: a survey on theories, techniques and applied systems. Part 2: qualitative function formation technique

    International Nuclear Information System (INIS)

    Far, B.H.

    1992-01-01

    Functional Reasoning (FR) enables people to derive the purpose of objects and explain their functions, JAERI's 'Human Acts Simulation Program (HASP)', started from 1987, has the goal of developing programs of the underlying technologies for intelligent robots by imitating the intelligent behavior of humans. FR is considered a useful reasoning method in HASP and applied to understand function of tools and objects in the Toolbox Project. In this report, first, the results of the diverse FR researches within a variety of disciplines are reviewed and the common core and basic problems are identified. Then the qualitative function formation (QFF) technique is introduced. Some novel points are: extending the common qualitative models to include interactions and timing of events by defining temporal and dependency constraints, and binding it with the conventional qualitative simulation. Function concepts are defined as interpretations of either a persistence or an order in the sequence of states, using the trace of the qualitative state vector derived by qualitative simulation on the extended qualitative model. This offers solution to some of the FR problems and leads to a method for generalization and comparison of functions of different objects. (author) 85 refs

  20. Modules de formation en durabilité et mobilisation des ressources

    International Development Research Centre (IDRC) Digital Library (Canada)

    Wind

    apprendre à lier la mobilisation des ressources à la planification stratégique; ... chercheurs et des ONG collaborant à des initiatives de défense de politiques. La ...... établissements membres à recruter des stagiaires qui ont contribué à la.

  1. A Model for Collaborative Working to Facilitate Knowledge Mobilisation in Public Health

    Science.gov (United States)

    McCabe, Karen Elizabeth; Wallace, Annie; Crosland, Ann

    2015-01-01

    This paper introduces a model for collaborative working to facilitate knowledge mobilisation in public health. The model has been developed by university researchers who worked collaboratively with public health commissioners and strategic partners to evaluate a portfolio of short-term funded interventions to inform re-commissioning. Within this…

  2. Room to Manoeuvre: Mobilising the "Active Partner" in Home-School Relations.

    Science.gov (United States)

    McNamara, Olwen; Hustler, David; Stronach, Ian; Rodrigo, Marta; Beresford, Emma; Botcherby, Sue

    2000-01-01

    Offers an interpretation of the dynamics of home-school relations in terms of a matrix of "mobilisations" and "demolisations" among parents, teachers, and children based upon data collected in an action research and development project. Aims to establish some bases for practical and theoretical "manoeuvers." (CMK)

  3. Finding Feminism, Finding Voice? Mobilising Community Education to Build Women's Participation in Myanmar's Political Transition

    Science.gov (United States)

    Maber, Elizabeth Jane Tregoning

    2016-01-01

    This paper explores the role played by women activists and educators in mobilising community education to support new opportunities for women's activism in the context of Myanmar's political transition. Recent political reorientations in Myanmar which have resulted in a civilian-led democracy emerging from a repressive military regime, have…

  4. Longwy: Higher Education and Health Mobilised in the Process of Regeneration

    Science.gov (United States)

    Hardouin, Magali; le Goff, Erwan

    2013-01-01

    For almost a century, Longwy has been one of the most important industrial areas of France, contributing the majority of the national production of cast iron and steel. The objective of this paper is to analyse how higher education, then health and well-being were mobilised in the process of regeneration of Longwy, which had been very harshly…

  5. Mobilisations collectives et femmes immigrées en France

    Directory of Open Access Journals (Sweden)

    Sylvie Thiéblemont-Dollet

    2008-09-01

    Full Text Available Si nombreuses que soient les études ayant trait à l’immigration en France (et plus particulièrement masculine, aborder l’immigration sous l’angle des femmes immigrées et des processus communicationnels qu'elles ont développés en terre d’accueil est un apport essentiel aux sciences humaines. C’est pourquoi, cet article traite du thème de la mobilisation collective entre 2000 et 2008, par le biais des actions et des processus communicationnels mis en œuvre par des femmes immigrées ou issues de l’immigration, originaires du Maghreb et de l’Afrique de l’Ouest, plus particulièrement à partir de l’exemple du mouvement Ni Putes Ni Soumises. Analyser les réseaux d’interdépendance et de « contagion » entre ces actrices aux origines sociales identiques, faisant que ces femmes expriment un sentiment d’exclusion et associent leur statut social (chômage, profession sous-qualifiée, ethnique (origine maghrébine ou africaine et spatial (cité, banlieue, quartier dit difficile, à un même stigmate les reléguant à un univers discriminatoire, dégager les spécificités de leurs paroles selon les espaces et les temporalités où elles ont été délivrées, saisir leurs manières de s’organiser et leurs possibilités de mobilisation, sont les grands axes de cette réflexion. Suggérer enfin que ces femmes constituent un corps social émergent et mutant est une autre manière de lire ce texte. Émergent, parce qu’il est relativement récent du point de vue de sa visibilité dans la sphère publique et mutant, parce qu’il intègre des femmes qui participent d’un changement en train de se faire dans la société française et qui donnent une nouvelle image d’elles : non pas celle de féministes au sens classique du terme et de ce qui peut s’y rattacher, mais celle qui s’inscrit dans la perspective de comportement de genre à entendre comme mixité et modalités d’interaction entre femmes et hommes. Enfin

  6. The MOVIN' project (Mobilisation Of Ventilated Intensive care patients at Nepean): A quality improvement project based on the principles of knowledge translation to promote nurse-led mobilisation of critically ill ventilated patients.

    Science.gov (United States)

    Hassan, Anwar; Rajamani, Arvind; Fitzsimons, Fiona

    2017-10-01

    Prospective quality improvement project to evaluate the impact of a training programme to promote nurse-led mobilisation of intubated critically ill patients. This project involved an educational programme to upskill nurses and overcome the barriers/challenges to nurse-led mobilisation. Initial strategies focused on educating and upskilling nurses to attain competency in active mobilisation. Subsequent strategies focused on positive reinforcement to achieve a culture shift. A pre- and post-intervention audit was used to evaluate its effectiveness. A baseline audit showed that ∼9% of ventilated patients were mobilised. Several barriers were identified. Twenty-three nurses underwent training in actively mobilising ventilated patients. This increased their confidence levels and there was reduction in reported barriers. However, the rate of active mobilisation remained low (9.7%). Subsequently, a programme of positive reinforcement with rewards and visual reminders was introduced, which saw an increase in the number of nurse-led mobilisations of both ventilated patients (from 9.7% to 34.8%; p=0.0003), and non-ventilated patients (29.5% versus 62.9%; p=patients. However, to promote a culture change, training and competency must be combined with a multi-pronged approach including reminders, positive reinforcement and rewards. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

  7. Effectiveness of exercise therapy and manual mobilisation in ankle sprain and functional instability: a systematic review.

    Science.gov (United States)

    van der Wees, Philip J; Lenssen, Anton F; Hendriks, Erik J M; Stomp, Derrick J; Dekker, Joost; de Bie, Rob A

    2006-01-01

    This study critically reviews the effectiveness of exercise therapy and manual mobilisation in acute ankle sprains and functional instability by conducting a systematic review of randomised controlled trials. Trials were searched electronically and manually from 1966 to March 2005. Randomised controlled trials that evaluated exercise therapy or manual mobilisation of the ankle joint with at least one clinically relevant outcome measure were included. Internal validity of the studies was independently assessed by two reviewers. When applicable, relative risk (RR) or standardised mean differences (SMD) were calculated for individual and pooled data. In total 17 studies were included. In thirteen studies the intervention included exercise therapy and in four studies the effects of manual mobilisation of the ankle joint was evaluated. Average internal validity score of the studies was 3.1 (range 1 to 7) on a 10-point scale. Exercise therapy was effective in reducing the risk of recurrent sprains after acute ankle sprain: RR 0.37 (95% CI 0.18 to 0.74), and with functional instability: RR 0.38 (95% CI 0.23 to 0.62). No effects of exercise therapy were found on postural sway in patients with functional instability: SMD: 0.38 (95% CI -0.15 to 0.91). Four studies demonstrated an initial positive effect of different modes of manual mobilisation on dorsiflexion range of motion. It is likely that exercise therapy, including the use of a wobble board, is effective in the prevention of recurrent ankle sprains. Manual mobilisation has an (initial) effect on dorsiflexion range of motion, but the clinical relevance of these findings for physiotherapy practice may be limited.

  8. Knowledge mobilisation for policy development: implementing systems approaches through participatory dynamic simulation modelling.

    Science.gov (United States)

    Freebairn, Louise; Rychetnik, Lucie; Atkinson, Jo-An; Kelly, Paul; McDonnell, Geoff; Roberts, Nick; Whittall, Christine; Redman, Sally

    2017-10-02

    Evidence-based decision-making is an important foundation for health policy and service planning decisions, yet there remain challenges in ensuring that the many forms of available evidence are considered when decisions are being made. Mobilising knowledge for policy and practice is an emergent process, and one that is highly relational, often messy and profoundly context dependent. Systems approaches, such as dynamic simulation modelling can be used to examine both complex health issues and the context in which they are embedded, and to develop decision support tools. This paper reports on the novel use of participatory simulation modelling as a knowledge mobilisation tool in Australian real-world policy settings. We describe how this approach combined systems science methodology and some of the core elements of knowledge mobilisation best practice. We describe the strategies adopted in three case studies to address both technical and socio-political issues, and compile the experiential lessons derived. Finally, we consider the implications of these knowledge mobilisation case studies and provide evidence for the feasibility of this approach in policy development settings. Participatory dynamic simulation modelling builds on contemporary knowledge mobilisation approaches for health stakeholders to collaborate and explore policy and health service scenarios for priority public health topics. The participatory methods place the decision-maker at the centre of the process and embed deliberative methods and co-production of knowledge. The simulation models function as health policy and programme dynamic decision support tools that integrate diverse forms of evidence, including research evidence, expert knowledge and localised contextual information. Further research is underway to determine the impact of these methods on health service decision-making.

  9. Applying aerial digital photography as a spectral remote sensing technique for macrophytic cover assessment in small rural streams

    Science.gov (United States)

    Anker, Y.; Hershkovitz, Y.; Gasith, A.; Ben-Dor, E.

    2011-12-01

    Although remote sensing of fluvial ecosystems is well developed, the tradeoff between spectral and spatial resolutions prevents its application in small streams (habitat scales classifications, acquisition of aerial digital RGB datasets. B. For section scale classification, hyperspectral (HSR) dataset acquisition. C. For calibration, HSR reflectance measurements of specific ground targets, in close proximity to each dataset acquisition swath. D. For habitat scale classification, manual, in-stream flora grid transects classification. The digital RGB datasets were converted to reflectance units by spectral calibration against colored reference plates. These red, green, blue, white, and black EVA foam reference plates were measured by an ASD field spectrometer and each was given a spectral value. Each spectral value was later applied to the spectral calibration and radiometric correction of spectral RGB (SRGB) cube. Spectral calibration of the HSR dataset was done using the empirical line method, based on reference values of progressive grey scale targets. Differentiation between the vegetation species was done by supervised classification both for the HSR and for the SRGB datasets. This procedure was done using the Spectral Angle Mapper function with the spectral pattern of each vegetation species as a spectral end member. Comparison between the two remote sensing techniques and between the SRGB classification and the in-situ transects indicates that: A. Stream vegetation classification resolution is about 4 cm by the SRGB method compared to about 1 m by HSR. Moreover, this resolution is also higher than of the manual grid transect classification. B. The SRGB method is by far the most cost-efficient. The combination of spectral information (rather than the cognitive color) and high spatial resolution of aerial photography provides noise filtration and better sub-water detection capabilities than the HSR technique. C. Only the SRGB method applies for habitat and

  10. Estimation of water quality parameters applying satellite data fusion and mining techniques in the lake Albufera de Valencia (Spain)

    Science.gov (United States)

    Doña, Carolina; Chang, Ni-Bin; Vannah, Benjamin W.; Sánchez, Juan Manuel; Delegido, Jesús; Camacho, Antonio; Caselles, Vicente

    2014-05-01

    Linked to the enforcement of the European Water Framework Directive (2000) (WFD), which establishes that all countries of the European Union have to avoid deterioration, improve and retrieve the status of the water bodies, and maintain their good ecological status, several remote sensing studies have been carried out to monitor and understand the water quality variables trend. Lake Albufera de Valencia (Spain) is a hypereutrophic system that can present chrorophyll a concentrations over 200 mg·m-3 and transparency (Secchi disk) values below 20 cm, needing to retrieve and improve its water quality. The principal aim of our work was to develop algorithms to estimate water quality parameters such as chlorophyll a concentration and water transparency, which are informative of the eutrophication and ecological status, using remote sensing data. Remote sensing data from Terra/MODIS, Landsat 5-TM and Landsat 7-ETM+ images were used to carry out this study. Landsat images are useful to analyze the spatial variability of the water quality variables, as well as to monitor small to medium size water bodies due to its 30-m spatial resolution. But, the poor temporal resolution of Landsat, with a 16-day revisit time, is an issue. In this work we tried to solve this data gap by applying fusion techniques between Landsat and MODIS images. Although the lower spatial resolution of MODIS is 250/500-m, one image per day is available. Thus, synthetic Landsat images were created using data fusion for no data acquisition dates. Good correlation values were obtained when comparing original and synthetic Landsat images. Genetic programming was used to develop models for predicting water quality. Using the reflectance bands of the synthetic Landsat images as inputs to the model, values of R2 = 0.94 and RMSE = 8 mg·m-3 were obtained when comparing modeled and observed values of chlorophyll a, and values of R2= 0.91 and RMSE = 4 cm for the transparency (Secchi disk). Finally, concentration

  11. Feasibility to apply the steam assisted gravity drainage (SAGD) technique in the country's heavy crude-oil fields

    International Nuclear Information System (INIS)

    Rodriguez, Edwin; Orjuela, Jaime

    2004-01-01

    The steam assisted gravity drainage (SAGD) processes are one of the most efficient and profitable technologies for the production of heavy crude oils and oil sands. These processes involve the drilling of a couple of parallel horizontal wells, separated by a vertical distance and located near the oil field base. The upper well is used to continuously inject steam into the zone of interest, while the lower well collects all resulting fluids (oil, condensate and formation water) and takes them to the surface (Butler, 1994). This technology has been successfully implemented in countries such as Canada, Venezuela and United States, reaching recovery factors in excess of 50%. This article provides an overview of the technique's operation mechanism and the process most relevant characteristics, as well as the various categories this technology is divided into, including all its advantages and limitations. Furthermore, the article sets the oil field's minimal conditions under which the SAGD process is efficient, which conditions, as integrated to a series of mathematical models, allow to make forecasts on production, thermal efficiency (ODR) and oil to be recovered, as long as it is feasible (from a technical point of view) to apply this technique to a defined oil field. The information and concepts compiled during this research prompted the development of software, which may be used as an information, analysis and interpretation tool to predict and quantify this technology's performance. Based on the article, preliminary studies were started for the country's heavy crude-oil fields, identifying which provide the minimum conditions for the successful development of a pilot project

  12. Fate of nitrogen in soil-crop system by nuclear techniques. Effects of applied rate of ammonium bicarbonate

    International Nuclear Information System (INIS)

    Chen Qing

    1996-11-01

    The experiment was conducted with 15 N tracing techniques in Shijiazhuang from 1994 to 1995. Three nitrogen rates, including optimum rate (150 kg/hm 2 ) based on the recommendation of local farmers, above 50% of optimum rate (225 kg/hm 2 ) and below 50% of optimum rate (75 kg/hm 2 ), were selected to study the effect of application rates of ammonium bicarbonate on yield of winter wheat and fate of applied nitrogen under local management and irrigated condition. The results showed that nitrogen uptake and grain yield of wheat under fertilized treatments were higher than those in unfertilized treatment (except 225 kg/hm 2 treatment). The highest yield and top dry mater weight (grain 6.80 t/hm 2 , top 14.70 t/hm 2 ) were obtained in optimum N applied treatment (150 kg/hm 2 ), while the highest nitrogen recovery efficiency (38.5%) of ammonium bicarbonate by winter wheat was found in below 50% of optimum rate treatment (75 kg/hm 2 ) due to the relatively high basic fertility of the field. However, nitrogen recovery efficiency of ammonium bicarbonate decreased with the increasing N application rate. The highest residue of fertilizer N was found in 225 kg/hm 2 treatment, and 46% of the residue existed in the top layer of the soil (0∼50 cm). The unaccounted N from fertilizer were 30.20%, 36.56%, 31.25% in 75 kg/hm 2 , 150 kg/hm 2 , 225 kg/hm 2 treatments respectively according to 15 N balance calculation in soil-plant system. The effect of residue N in soil on the next crop, maize, in 225 kg/hm 2 treatment was best in three fertilized treatments, suggesting the possibilities of nitrate leaching down in 225 kg/hm 2 treatment. (15 tabs.)

  13. The Small-scale Structure of Photospheric Convection Retrieved by a Deconvolution Technique Applied to Hinode /SP Data

    Energy Technology Data Exchange (ETDEWEB)

    Oba, T. [SOKENDAI (The Graduate University for Advanced Studies), 3-1-1 Yoshinodai, Chuo-ku, Sagamihara, Kanagawa 252–5210 (Japan); Riethmüller, T. L.; Solanki, S. K. [Max-Planck-Institut für Sonnensystemforschung (MPS), Justus-von-Liebig-Weg 3, D-37077 Göttingen (Germany); Iida, Y. [Department of Science and Technology/Kwansei Gakuin University, Gakuen 2-1, Sanda, Hyogo, 669–1337 Japan (Japan); Quintero Noda, C.; Shimizu, T. [Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency, 3-1-1 Yoshinodai, Chuo-ku, Sagamihara, Kanagawa 252–5210 (Japan)

    2017-11-01

    Solar granules are bright patterns surrounded by dark channels, called intergranular lanes, in the solar photosphere and are a manifestation of overshooting convection. Observational studies generally find stronger upflows in granules and weaker downflows in intergranular lanes. This trend is, however, inconsistent with the results of numerical simulations in which downflows are stronger than upflows through the joint action of gravitational acceleration/deceleration and pressure gradients. One cause of this discrepancy is the image degradation caused by optical distortion and light diffraction and scattering that takes place in an imaging instrument. We apply a deconvolution technique to Hinode /SP data in an attempt to recover the original solar scene. Our results show a significant enhancement in both the convective upflows and downflows but particularly for the latter. After deconvolution, the up- and downflows reach maximum amplitudes of −3.0 km s{sup −1} and +3.0 km s{sup −1} at an average geometrical height of roughly 50 km, respectively. We found that the velocity distributions after deconvolution match those derived from numerical simulations. After deconvolution, the net LOS velocity averaged over the whole field of view lies close to zero as expected in a rough sense from mass balance.

  14. 3D-QSPR Method of Computational Technique Applied on Red Reactive Dyes by Using CoMFA Strategy

    Directory of Open Access Journals (Sweden)

    Shahnaz Perveen

    2011-12-01

    Full Text Available Cellulose fiber is a tremendous natural resource that has broad application in various productions including the textile industry. The dyes, which are commonly used for cellulose printing, are “reactive dyes” because of their high wet fastness and brilliant colors. The interaction of various dyes with the cellulose fiber depends upon the physiochemical properties that are governed by specific features of the dye molecule. The binding pattern of the reactive dye with cellulose fiber is called the ligand-receptor concept. In the current study, the three dimensional quantitative structure property relationship (3D-QSPR technique was applied to understand the red reactive dyes interactions with the cellulose by the Comparative Molecular Field Analysis (CoMFA method. This method was successfully utilized to predict a reliable model. The predicted model gives satisfactory statistical results and in the light of these, it was further analyzed. Additionally, the graphical outcomes (contour maps help us to understand the modification pattern and to correlate the structural changes with respect to the absorptivity. Furthermore, the final selected model has potential to assist in understanding the charachteristics of the external test set. The study could be helpful to design new reactive dyes with better affinity and selectivity for the cellulose fiber.

  15. 3D-QSPR method of computational technique applied on red reactive dyes by using CoMFA strategy.

    Science.gov (United States)

    Mahmood, Uzma; Rashid, Sitara; Ali, S Ishrat; Parveen, Rasheeda; Zaheer-Ul-Haq; Ambreen, Nida; Khan, Khalid Mohammed; Perveen, Shahnaz; Voelter, Wolfgang

    2011-01-01

    Cellulose fiber is a tremendous natural resource that has broad application in various productions including the textile industry. The dyes, which are commonly used for cellulose printing, are "reactive dyes" because of their high wet fastness and brilliant colors. The interaction of various dyes with the cellulose fiber depends upon the physiochemical properties that are governed by specific features of the dye molecule. The binding pattern of the reactive dye with cellulose fiber is called the ligand-receptor concept. In the current study, the three dimensional quantitative structure property relationship (3D-QSPR) technique was applied to understand the red reactive dyes interactions with the cellulose by the Comparative Molecular Field Analysis (CoMFA) method. This method was successfully utilized to predict a reliable model. The predicted model gives satisfactory statistical results and in the light of these, it was further analyzed. Additionally, the graphical outcomes (contour maps) help us to understand the modification pattern and to correlate the structural changes with respect to the absorptivity. Furthermore, the final selected model has potential to assist in understanding the characteristics of the external test set. The study could be helpful to design new reactive dyes with better affinity and selectivity for the cellulose fiber.

  16. Physical and Clinical Evaluation of Hip Spica Cast applied with Three-slab Technique using Fibreglass Material

    Directory of Open Access Journals (Sweden)

    Bitar KM

    2016-11-01

    Full Text Available Introduction: Hip spica casting is an important component of treatment for developmental dysplasia of the hip (DDH and popular treatment method for femur fractures in children. Breakage at the hip region is a relatively common problem of this cast. We have developed a three-slab technique of hip spica application using fibreglass as the cast material. The purpose of this review was to evaluate the physical durability of the spica cast and skin complications with its use. Methodology: A retrospective review of children with various conditions requiring hip spica immobilisation which was applied using our method. Study duration was from 1st of January 2014 until 31st December 2015. Our main outcomes were cast breakage and skin complications. For children with hip instability, the first cast would be changed after one month, and the second cast about two months later. Results: Twenty-one children were included, with an average age of 2.2 years. The most common indication for spica immobilisation was developmental dysplasia of the hip. One child had skin irritation after spica application. No spica breakage was noted. Conclusion: This study showed that the three-slab method of hip spica cast application using fibreglass material was durable and safe with low risk of skin complications.

  17. Optimization of methodology for the assessing of bioaccumulation factors of periphyton metals applying the X-ray fluorescence technique

    International Nuclear Information System (INIS)

    Merced Ch, D.

    2015-01-01

    The Lerma River is one of the most polluted at Mexico, has a high pollutant load and low biodiversity, this aquatic plants and species zoo perifiton presented adaptations to environmental conditions that exist due to dumping of wastewater are developed. In this paper bioaccumulation factors (BAF) of Cr, Mn, Fe, Ni, Cu, Zn and Pb metal on Hydrocotyle ranunculoides zoo perifiton associated with the upper reaches of the Lerma River applying the technique of fluorescence X-rays were evaluated in the form of Total Reflection. The BAF were higher compared to the soluble fraction to the total fraction this because the metal in the soluble phase are in solution and are therefore more available to join aquatic organisms, moreover respect to the BAF sediment were ≤ 1.5 indicate that these organisms have little affinity for incorporating metals from the sediment. Considering the sum of the FBA of all metals in each agency notes that the leech was the biggest bio accumulated metals (42468) followed by the worm to (27958), the arthropod with (10757) and finally the snail with (8421). Overall for this study agencies according to the BAF reported to bio accumulate metals are the following behavior Fe > Zn > Cu > Cr > Ni > Mn > Pb. (Author)

  18. Results of Applying Cultural Domain Analysis Techniques and Implications for the Design of Complementary Feeding Interventions in Northern Senegal.

    Science.gov (United States)

    Zobrist, Stephanie; Kalra, Nikhila; Pelto, Gretel; Wittenbrink, Brittney; Milani, Peiman; Diallo, Abdoulaye Moussa; Ndoye, Tidiane; Wone, Issa; Parker, Megan

    2017-12-01

    Designing effective nutrition interventions for infants and young children requires knowledge about the population to which the intervention is directed, including insights into the cognitive systems and values that inform caregiver feeding practices. To apply cultural domain analysis techniques in the context of implementation research for the purpose of understanding caregivers' knowledge frameworks in Northern Senegal with respect to infant and young child (IYC) feeding. This study was intended to inform decisions for interventions to improve infant and young child nutrition. Modules from the Focused Ethnographic Study for Infant and Young Child Feeding Manual were employed in interviews with a sample of 126 key informants and caregivers from rural and peri-urban sites in the Saint-Louis region of northern Senegal. Descriptive statistics, cluster analysis, and qualitative thematic analysis were used to analyze the data. Cluster analysis showed that caregivers identified 6 food clusters: heavy foods, light foods, snack foods, foraged foods, packaged foods, and foods that are good for the body. The study also revealed similarities and differences between the 2 study sites in caregivers' knowledge frameworks. The demonstration of differences between biomedical concepts of nutrition and the knowledge frameworks of northern Senegalese women with regard to IYC feeding highlights the value of knowledge about emic perspectives of local communities to help guide decisions about interventions to improve nutrition.

  19. UQ and V&V techniques applied to experiments and simulations of heated pipes pressurized to failure

    Energy Technology Data Exchange (ETDEWEB)

    Romero, Vicente Jose [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dempsey, J. Franklin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Antoun, Bonnie R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-05-01

    This report demonstrates versatile and practical model validation and uncertainty quantification techniques applied to the accuracy assessment of a computational model of heated steel pipes pressurized to failure. The Real Space validation methodology segregates aleatory and epistemic uncertainties to form straightforward model validation metrics especially suited for assessing models to be used in the analysis of performance and safety margins. The methodology handles difficulties associated with representing and propagating interval and/or probabilistic uncertainties from multiple correlated and uncorrelated sources in the experiments and simulations including: material variability characterized by non-parametric random functions (discrete temperature dependent stress-strain curves); very limited (sparse) experimental data at the coupon testing level for material characterization and at the pipe-test validation level; boundary condition reconstruction uncertainties from spatially sparse sensor data; normalization of pipe experimental responses for measured input-condition differences among tests and for random and systematic uncertainties in measurement/processing/inference of experimental inputs and outputs; numerical solution uncertainty from model discretization and solver effects.

  20. Improving Air Quality (and Weather) Predictions using Advanced Data Assimilation Techniques Applied to Coupled Models during KORUS-AQ

    Science.gov (United States)

    Carmichael, G. R.; Saide, P. E.; Gao, M.; Streets, D. G.; Kim, J.; Woo, J. H.

    2017-12-01

    Ambient aerosols are important air pollutants with direct impacts on human health and on the Earth's weather and climate systems through their interactions with radiation and clouds. Their role is dependent on their distributions of size, number, phase and composition, which vary significantly in space and time. There remain large uncertainties in simulated aerosol distributions due to uncertainties in emission estimates and in chemical and physical processes associated with their formation and removal. These uncertainties lead to large uncertainties in weather and air quality predictions and in estimates of health and climate change impacts. Despite these uncertainties and challenges, regional-scale coupled chemistry-meteorological models such as WRF-Chem have significant capabilities in predicting aerosol distributions and explaining aerosol-weather interactions. We explore the hypothesis that new advances in on-line, coupled atmospheric chemistry/meteorological models, and new emission inversion and data assimilation techniques applicable to such coupled models, can be applied in innovative ways using current and evolving observation systems to improve predictions of aerosol distributions at regional scales. We investigate the impacts of assimilating AOD from geostationary satellite (GOCI) and surface PM2.5 measurements on predictions of AOD and PM in Korea during KORUS-AQ through a series of experiments. The results suggest assimilating datasets from multiple platforms can improve the predictions of aerosol temporal and spatial distributions.

  1. Simulation modelling as a tool for knowledge mobilisation in health policy settings: a case study protocol.

    Science.gov (United States)

    Freebairn, L; Atkinson, J; Kelly, P; McDonnell, G; Rychetnik, L

    2016-09-21

    Evidence-informed decision-making is essential to ensure that health programs and services are effective and offer value for money; however, barriers to the use of evidence persist. Emerging systems science approaches and advances in technology are providing new methods and tools to facilitate evidence-based decision-making. Simulation modelling offers a unique tool for synthesising and leveraging existing evidence, data and expert local knowledge to examine, in a robust, low risk and low cost way, the likely impact of alternative policy and service provision scenarios. This case study will evaluate participatory simulation modelling to inform the prevention and management of gestational diabetes mellitus (GDM). The risks associated with GDM are well recognised; however, debate remains regarding diagnostic thresholds and whether screening and treatment to reduce maternal glucose levels reduce the associated risks. A diagnosis of GDM may provide a leverage point for multidisciplinary lifestyle modification interventions. This research will apply and evaluate a simulation modelling approach to understand the complex interrelation of factors that drive GDM rates, test options for screening and interventions, and optimise the use of evidence to inform policy and program decision-making. The study design will use mixed methods to achieve the objectives. Policy, clinical practice and research experts will work collaboratively to develop, test and validate a simulation model of GDM in the Australian Capital Territory (ACT). The model will be applied to support evidence-informed policy dialogues with diverse stakeholders for the management of GDM in the ACT. Qualitative methods will be used to evaluate simulation modelling as an evidence synthesis tool to support evidence-based decision-making. Interviews and analysis of workshop recordings will focus on the participants' engagement in the modelling process; perceived value of the participatory process, perceived

  2. Investigation of The Effects of Connective Tissue Mobilisation on ...

    African Journals Online (AJOL)

    Background: Connective Tissue Massage (CTM) or Manipulation is a bodywork technique which lies at the interface between alternative approaches. The autonomic balancing responses to CTM can be useful in the treatment of anxiety. Aim: This study was planned to investigate the effects of connective tissue mobilization ...

  3. A Brief Discussion on the Decision Aiding Techniques Applied to a Laboratory of Radioactive Decontamination: A General Case

    International Nuclear Information System (INIS)

    Kodma, Y.; Sordi, G. M. A. A.; Rodrigues, D. L.

    2004-01-01

    In the Laboratory of Radioactive Decontamination ( RDL ) at the Instituto de Pesquisas Energeticas e Nucleares IPEN it has been received objects and equipments from the various installations, each one processing different kinds of radioisotopes. These radioactive materials can range from nuclear fuel fabrication and processing, research reactor utilization or radiopharmaceuticals production. This means many different physical and chemical properties of the contaminants and composition of the contaminated surface. It is difficult to decide whether to decontaminate or not the objects and equipment that were used on the processing of these radioactive materials. Most of the radioactive contamination are transferable ones but some are fixed that would imply in more effort to reduce the contamination levels. Depending on the reuse or on the repairing need, for instance, of equipments, tools or objects, the permissible levels of remaining contamination varies and for so the decontamination process shall be more severe. Several parameters must be considered to make a decision, not only their cost to buy new ones compared to the cost of the materials and personnel those will execute the decontamination, but also the installation budget to buy new equipments, collective dose of the workers, readiness for reuse and so on. In this work we discuss how the parameters influence on the decision about decontaminate or not and if so, up to where to proceed. We also compare the decision aiding techniques applied to a general case considering some parameters those are fundamental and others that are not so important all the time but can affect in a significant way the decontamination choice and the way they can affect the decision maker to choose the best option. (Author) 8 refs

  4. Nuclear and conventional techniques applied to the analysis of prehispanic metals of the Templo Mayor of Tenochtitlan

    International Nuclear Information System (INIS)

    Mendez M, U.

    2003-01-01

    The use of the such experimental techniques as: PIXE, RBS, Metallography and Sem, applied to the characterization of pre hispanic metals of copper and gold coming from 9 offerings of the Templo Mayor of Tenochtitlan, are possible to obtain results and information sustained on such aspects as technological development and cultural and commercial exchange besides a relative chronology, as well as aspects related with conservation, authenticity, symbolic association and social meaning of the offerings. After way but it specifies, it will be given to know each one of the objectives outlined for this study: To carry out interpretations on technical of factory, stylistic designs and cultural and commercial exchanges starting from aspects like: microstructure, elementary composition, type of alloys, welding existence, golden superficial, and conservation, they can be had. To determine the technological advance that means the prosecution of the metallic materials and to know their location in the archaeological context, as a means for the interpretation of the social significance of the offering. To know the possible association symbolic-religious from the metallic objects offering to the deities; starting from significant characteristics as they are: color, forms and function. To establish if it is possible to know if the devices found in the offerings are of the same temporality in which one carries out this, or at least, to locate to the devices inside the two stages of the development of the metallurgy these they are known as the period of the native copper and the period of the alloys, this helped to determine a relative chronology of when the objects were manufactured. To confirm the authenticity of the devices. To determine, in a way specifies, the conservation grade in that they are the pieces. To corroborate some of the manufacture processes This is achieved by means of the reproduction of objects in laboratory, to establish comparisons and differences among pre

  5. Convalescence and hospital stay after colonic surgery with balanced analgesia, early oral feeding, and enforced mobilisation

    DEFF Research Database (Denmark)

    Møiniche, S; Bülow, Steffen; Hesselfeldt, Peter

    1995-01-01

    OBJECTIVE: To evaluate the combined effects of pain relief by continuous epidural analgesia, early oral feeding and enforced mobilisation on convalescence and hospital stay after colonic resection. DESIGN: Uncontrolled pilot investigation. SETTING: University hospital, Denmark. SUBJECTS: 17...... unselected patients (median age 69 years) undergoing colonic resection. INTERVENTIONS: Patients received combined epidural and general anaesthesia during operations and after operation were given continuous epidural bupivacaine 0.25%, 4 ml hour and morphine 0.2 mg hour, for 96 hours and oral paracetamol 4 g...... weight loss. CONCLUSION: These results suggest that a combined approach of optimal pain relief with balanced analgesia, enforced early mobilisation, and oral feeding, may reduce the length of convalescence and hospital stay after colonic operations....

  6. Exploring mechanisms for mobilising industrial sustainability models across different industrial locations

    DEFF Research Database (Denmark)

    Jacobsen, Ole Morten Noel Brings

    2009-01-01

    Industrial symbiosis is a model of sustainability which suggests that agglomerations of industries can achieve considerable environmental benefits by engaging in inter-organisational waste recycling, energy cascading and water recovery. This article considers how such a complex inter-organisation......Industrial symbiosis is a model of sustainability which suggests that agglomerations of industries can achieve considerable environmental benefits by engaging in inter-organisational waste recycling, energy cascading and water recovery. This article considers how such a complex inter...... symbiosis model may in this way be mobilised across industrial localities as part of the global corporate search for marked access and cost reductions. This suggestion is supported by an illustrative case study shedding some light on the mechanisms for mobilising sustainability models across localities....

  7. Mobile museology:An exploration of fashionable museums, mobilisation, and trans-museal mediation

    OpenAIRE

    Baggesen, Rikke Haller

    2015-01-01

    Drawing together perspectives from museology, digital culture studies and fashion theory, this thesis considers changes in and challenges for current - day museums as related to ‘mobile museology’. This concept is developed for and elucidated in the thesis to describe an orientation towards the fashionable, the ephemeral, and towards an (ideal) state of change and changeability. This orientation is characterised with the triplet concepts of mobile, mobility, and mobilisation, as related to mo...

  8. Decision-Making Tool for Cost-Efficient and Environmentally Friendly Wood Mobilisation

    OpenAIRE

    Matevž Triplat; Peter Prislan; Nike Krajnc

    2015-01-01

    Background and Purpose: With development of forest management technologies, the efficiency of wood production was significantly improved, and thus the impact on forests has changed as well. The article presents a practical decision-making tool for selection of most suitable harvesting system, considering given terrain as well as expected soil conditions on harvesting sites. The decision-making tool should support cost-efficient and environmentally friendly mobilisation of wood. Materials a...

  9. Towards a "fourth generation" of approaches to HIV/AIDS management: creating contexts for effective community mobilisation.

    Science.gov (United States)

    Campbell, Catherine; Cornish, Flora

    2010-01-01

    Many biomedical and behavioural HIV/AIDS programmes aimed at prevention, care and treatment have disappointing outcomes because of a lack of effective community mobilisation. But community mobilisation is notoriously difficult to bring about. We present a conceptual framework that maps out those dimensions of social context that are likely to support or undermine community mobilisation efforts, proposing that attention should be given to three dimensions of social context: the material, symbolic and relational. This paper has four parts. We begin by outlining why community mobilisation is regarded as a core dimension of effective HIV/AIDS management: it increases the "reach" and sustainability of programmes; it is a vital component of the wider "task shifting" agenda given the scarcity of health professionals in many HIV/AIDS-vulnerable contexts. Most importantly it facilitates those social psychological processes that we argue are vital preconditions for effective prevention, care and treatment. Secondly we map out three generations of approaches to behaviour change within the HIV/AIDS field: HIV-awareness, peer education and community mobilisation. We critically evaluate each approach's underlying assumptions about the drivers of behaviour change, to frame our understandings of the pathways between mobilisation and health, drawing on the concepts of social capital, dialogue and empowerment. Thirdly we refer to two well-documented case studies of community mobilisation in India and South Africa to illustrate our claim that community mobilisation is unlikely to succeed in the absence of supportive material, symbolic and relational contexts. Fourthly we provide a brief overview of how the papers in this special issue help us flesh out our conceptualisation of the "health enabling social environment". We conclude by arguing for the urgent need for a 'fourth generation' of approaches in the theory and practice of HIV/AIDS management, one which pays far greater

  10. Overseas Voter Mobilisation in Singapore: Implications from Malaysia’s 13th General Election

    OpenAIRE

    James Gomez; Rusdi Omar

    2013-01-01

    This paper discusses voter mobilisation and other election-related activities of Malaysian voters living, studying and working in Singapore in the context of Malaysia’s 13th general election (GE13). According to the World Bank, nearly 400,000 Malaysians reside in the city-state. Thus these figures represent a significant Malaysian voter pool based in Singapore. Efforts to mobilise these voters for general elections or other causes have political implications for both countries, which became...

  11. Mobilisation, alteration, and redistribution of monosulfidic sediments in inland river systems.

    Science.gov (United States)

    Cheetham, M D; Wong, V N L; Bush, R T; Sullivan, L A; Ward, N J; Zawadzki, A

    2012-12-15

    The accumulation of monosulfidic sediments in inland waterways is emerging as a major environmental issue. Mobilisation and suspension of monosulfidic sediments can result in deoxygenation, acidification of the water column and mobilisation of trace metals. The controls on monosulfidic sediment mobilisation and the critical thresholds for its scour and entrainment have not been established. This study examines the effect of a minor flood event (average return interval of 5 years) on sulfidic sediment scour in the Wakool River in southern NSW, Australia. Five profiles were sampled within a small (~300 m) reach before and after a minor flood event to determine the degree of sediment scour and transport. The results indicate substantial scour of both monosulfidic sediments and underlying bed sediments (approximately 2100 m(3)). Changes in the sediment geochemistry suggest large concentrations of monosulfidic sediments had been suspended in the water column, partially-oxidised and redeposited. This is supported by (210)Pb results from one of the profiles. These results suggest that these monosulfidic sediments can move as bed load during minor flood events. Copyright © 2012 Elsevier Ltd. All rights reserved.

  12. Neutron scattering techniques for betaine calcium chloride dihydrate under applied external field (temperature, electric field and hydrostatic pressure)

    International Nuclear Information System (INIS)

    Hernandez, O.

    1997-01-01

    We have studied with neutron scattering techniques betaine calcium chloride dihydrate (BCCD), a dielectric aperiodic crystal which displays a Devil's staircase type phase diagram made up of several incommensurate and commensurate phases, having a range of stability very sensitive to temperature, electric field and hydrostatic pressure. We have measured a global hysteresis of δ(T) of about 2-3 K in the two incommensurate phases. A structural study of the modulated commensurate phases 1/4 and 1/5 allows us to evidence that the atomic modulation functions are anharmonic. The relevance of the modelization of the modulated structure by polar Ising pseudo-spins is then directly established. On the basis of group theory calculation in the four dimensional super-space, we interpret this anharmonic modulation as a soliton regime with respect to the lowest-temperature non modulated ferroelectric phase. The continuous character of the transition to the lowest-temperature non modulated phase and the diffuse scattering observed in this phase are accounted for the presence of ferroelectric domains separated by discommensurations. Furthermore, we have shown that X-rays induce in BCCD a strong variation with time of irradiation of the intensity of satellite peaks, and more specifically for third order ones. This is why the 'X-rays' structural model is found more harmonic than the 'neutron' one. Under electric field applied along the vector b axis, we confirm that commensurate phases with δ = even/odd are favoured and hence are polar along this direction. We have evidenced at 10 kV / cm two new higher order commensurate phases in the phase INC2, corroborating the idea of a 'complete' Devil's air-case phase diagram. A phenomenon of generalized coexistence of phases occurs above 5 kV / cm. We have characterized at high field phase transitions between 'coexisting' phases, which are distinguishable from classical lock-in transitions. Under hydrostatic pressure, our results contradict

  13. A review of the Match technique as applied to AASE-2/EASOE and SOLVE/THESEO 2000

    Directory of Open Access Journals (Sweden)

    G. A. Morris

    2005-01-01

    Full Text Available We apply the NASA Goddard Trajectory Model to data from a series of ozonesondes to derive ozone loss rates in the lower stratosphere for the AASE-2/EASOE mission (January-March 1992 and for the SOLVE/THESEO 2000 mission (January-March 2000 in an approach similar to Match. Ozone loss rates are computed by comparing the ozone concentrations provided by ozonesondes launched at the beginning and end of the trajectories connecting the launches. We investigate the sensitivity of the Match results to the various parameters used to reject potential matches in the original Match technique. While these filters effectively eliminate from consideration 80% of the matched sonde pairs and >99% of matched observations in our study, we conclude that only a filter based on potential vorticity changes along the calculated back trajectories seems warranted. Our study also demonstrates that the ozone loss rates estimated in Match can vary by up to a factor of two depending upon the precise trajectory paths calculated for each trajectory. As a result, the statistical uncertainties published with previous Match results might need to be augmented by an additional systematic error. The sensitivity to the trajectory path is particularly pronounced in the month of January, for which the largest ozone loss rate discrepancies between photochemical models and Match are found. For most of the two study periods, our ozone loss rates agree with those previously published. Notable exceptions are found for January 1992 at 475K and late February/early March 2000 at 450K, both periods during which we generally find smaller loss rates than the previous Match studies. Integrated ozone loss rates estimated by Match in both of those years compare well with those found in numerous other studies and in a potential vorticity/potential temperature approach shown previously and in this paper. Finally, we suggest an alternate approach to Match using trajectory mapping. This approach uses

  14. The Cs-137 technique applied to steep Mediterranean slopes (Part I) : the effects of lithology, slope morphology and land use

    NARCIS (Netherlands)

    de Meijer, R.J.; van der Graaf, E.R.

    2004-01-01

    Concentrations in the soil of anthropogenic and natural radionuclides have been investigated in order to assess the applicability of the Cs-137 technique in an area of typical Mediterranean steep slopes. This technique can be used to estimate net soil redistribution rates but its potential in areas

  15. The 137Cs technique applied to steep Mediterranean slopes (Part I): the effects of lithology, slope morphology and land use

    NARCIS (Netherlands)

    Schoorl, J.M.; Boix Fayos, C.; Meijer, de R.J.; Graaff, van der E.R.; Veldkamp, A.

    2004-01-01

    Concentrations in the soil of anthropogenic and natural radionuclides have been investigated in order to assess the applicability of the Cs-137 technique in an area of typical Mediterranean steep slopes. This technique can be used to estimate net soil redistribution rates but its potential in areas

  16. A Survey on Optimal Signal Processing Techniques Applied to Improve the Performance of Mechanical Sensors in Automotive Applications

    Science.gov (United States)

    Hernandez, Wilmar

    2007-01-01

    In this paper a survey on recent applications of optimal signal processing techniques to improve the performance of mechanical sensors is made. Here, a comparison between classical filters and optimal filters for automotive sensors is made, and the current state of the art of the application of robust and optimal control and signal processing techniques to the design of the intelligent (or smart) sensors that today's cars need is presented through several experimental results that show that the fusion of intelligent sensors and optimal signal processing techniques is the clear way to go. However, the switch between the traditional methods of designing automotive sensors and the new ones cannot be done overnight because there are some open research issues that have to be solved. This paper draws attention to one of the open research issues and tries to arouse researcher's interest in the fusion of intelligent sensors and optimal signal processing techniques.

  17. Uranium exploration data and techniques applied to the preparation of radioelement maps. Proceedings of a technical committee meeting

    International Nuclear Information System (INIS)

    1997-11-01

    The report reviews the advantage and pitfalls of using uranium exploration data and techniques as well as other methods for the preparation of radioelement and radon maps for baseline information in environmental studies and monitoring

  18. Uranium exploration data and techniques applied to the preparation of radioelement maps. Proceedings of a technical committee meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    The report reviews the advantage and pitfalls of using uranium exploration data and techniques as well as other methods for the preparation of radioelement and radon maps for baseline information in environmental studies and monitoring. Refs, figs, tabs.

  19. Statistical techniques applied to aerial radiometric surveys (STAARS): series introduction and the principal-components-analysis method

    International Nuclear Information System (INIS)

    Pirkle, F.L.

    1981-04-01

    STAARS is a new series which is being published to disseminate information concerning statistical procedures for interpreting aerial radiometric data. The application of a particular data interpretation technique to geologic understanding for delineating regions favorable to uranium deposition is the primary concern of STAARS. Statements concerning the utility of a technique on aerial reconnaissance data as well as detailed aerial survey data will be included

  20. Physical Modelling of Axisymmetric Turbulent Impinging Jets as used within the Nuclear Industry for Mobilisation of Sludges

    International Nuclear Information System (INIS)

    McKendrick, D.; Biggs, S.R.; Fairweather, M.; Rhodes, D.

    2008-01-01

    The impingement of a fluid jet onto a surface has broad applications across many industries. Within the UK nuclear industry, during the final stages of fuel reprocessing, impinging fluid jets are utilised to mobilise settled sludge material within storage tanks and ponds in preparation for transfer and ultimate immobilisation through vitrification. Despite the extensive applications of impinging jets within the nuclear and other industries, the study of two-phase, solid loaded, impinging jets is limited, and generally restricted to computational modelling. Surprisingly, very little fundamental understanding of the turbulence structure within such fluid flows through experimental investigation is found within the literature. The physical modelling of impinging jet systems could successfully serve to aid computer model validation, determine operating requirements, evaluate plant throughput requirements, optimise process operations and support design. Within this project a method is illustrated, capable of exploring the effects of process and material variables on flow phenomena of impinging jets. This is achieved via the use of non-intrusive measurement techniques Particle Image Velocimetry (PIV), Ultrasonic Doppler Velocity Profiler (UDVP) and high speed imaging. The turbulence structure for impinging jets, and their resultant radial wall jets, is presented at different jet-to-plate ratios, jet Reynolds numbers and jet outlet diameters. (authors)

  1. A study on the hollow-out radiation technique applied to the protection of the spinal cord

    International Nuclear Information System (INIS)

    Matsuda, Tadayoshi

    1975-01-01

    The hollow-out radiation technique to protect the spinal cord in linear accelerator X-ray treatment of malignant diseases has been established in this study. Several kinds of diseases were selected as the subjects of the hollow-out technique to protect the cervical spinal cord, thoracic spinal cord, and dorsolumbar spinal cord from radiation, plus fundamental data, such as the materials, shapes and sizes of absorber, which are most appropriate for each of the diseases, were established. In all the cases receiving this technique, the necessary areas of therapy are covered by 80-90% dose distribution and the radiation dose of the spinal cord is kept below 40%. The fundamental data and irradiation conditions for the hollow-out technique of every part of the spinal cord were arranged from the results of phantom examinations on every part of the human body and from 42 cases actually treated. In the present study, the hollow-out technique for the cervical spinal cord, thoracic spinal cord, and dorsolumbar spinal cord is divided into 5 categories, and a method for the planning of radiation therapy and the actual treatment are described. The hollow-out radiation technique on the spinal cord is useful radiation therapy which can give better results by preventing radiation myelopathy. (auth.)

  2. Speleothem records of acid sulphate deposition and organic carbon mobilisation

    Science.gov (United States)

    Wynn, Peter; Fairchild, Ian; Bourdin, Clement; Baldini, James; Muller, Wolfgang; Hartland, Adam; Bartlett, Rebecca

    2017-04-01

    Dramatic increases in measured surface water DOC in recent decades have been variously attributed to either temperature rise, or destabilisation of long-term soil carbon pools following sulphur peak emissions status. However, whilst both drivers of DOC dynamics are plausible, they remain difficult to test due to the restricted nature of the available records of riverine DOC flux (1978 to present), and the limited availability of SO2 emissions inventory data at the regional scale. Speleothems offer long term records of both sulphur and carbon. New techniques to extract sulphur concentrations and isotopes from speleothem calcite have enabled archives of pollution history and environmental acidification to be reconstructed. Due to the large dynamic range in sulphur isotopic values from end member sources (marine aerosol +21 ‰ to continental biogenic emissions -30 ‰) and limited environmental fractionation under oxidising conditions, sulphur isotopes form an ideal tracer of industrial pollution and environmental acidification in the palaeo-record. We couple this acidification history to the carbon record, using organic matter fluorescence and trace metals. Trace metal ratios and abundance can be used to infer the type and size of organic ligand and are therefore sensitive to changes in temperature as a driver of organic carbon processing and biodegradation. This allows fluorescent properties and ratios of trace metals in speleothem carbonate to be used to represent both the flux of organic carbon into the cave as well as the degradation pathway. Here we present some of the first results of this work, exploring sulphur acidification as a mechanistic control on carbon solubility and export throughout the twentieth century.

  3. Methodology to evaluate the impact of the erosion in cultivated floors applying the technique of the 137CS

    International Nuclear Information System (INIS)

    Gil Castillo, R.; Peralta Vital, J.L.; Carrazana, J.; Riverol, M.; Penn, F.; Cabrera, E.

    2004-01-01

    The present paper shows the results obtained in the framework of 2 Nuclear Projects, in the topic of application of nuclear techniques to evaluate the erosion rates in cultivated soils. Taking into account the investigations with the 137 CS technique, carried out in the Province of Pinar del Rio, was obtained and validated (first time) a methodology to evaluate the erosion impact in a cropland. The obtained methodology includes all relevant stages for the adequate application of the 137 CS technique, from the initial step of area selection, the soil sampling process, selection of the models and finally, the results evaluation step. During the methodology validation process in soils of the Municipality of San Juan y Martinez, the erosion rates estimated by the methodology and the obtained values by watershed segment measures (traditional technique) were compared in a successful manner. The methodology is a technical guide, for the adequate application of the 137 CS technique to estimate the soil redistribution rates in cultivated soils

  4. Proposal of requirements for performance in Brazil for systems of external individual monitoring for neutrons applying the TLD-albedo technique

    International Nuclear Information System (INIS)

    Martins, Marcelo M.; Mauricio, Claudia L.P.; Pereira, Walsan W.; Fonseca, Evaldo S. da; Silva, Ademir X.

    2009-01-01

    This work presents a criteria and conditions proposal for the regulations in Brazil of individual monitoring systems for neutrons applying the albedo technique with thermoluminescent detectors. Tests are proposed for the characterization performance of the system based on the Regulation ISO 21909 and on the experience of the authors

  5. Study on rice absorption and distribution of Cd in applying Zn fertilizer with 65Zn, 115Cdm tracing technique

    International Nuclear Information System (INIS)

    Tang Nianxin; Shen Jinxiong

    1994-01-01

    Results of study by using 65 Zn and 115 Cd m tracers show that, along with the increase of the amount of Cd in applying Zn fertilizer to soil, rice has the phenomena of growth retard and tiller delay in the earlier growing stage. The inhibiting phenomenon is lightened along with the progress of rice growth. Very small quantity of Cd might be helpful to the growth of rice. It would cause serious inhibition to rice growth when the amount of Cd reaches to a definite limitation (64 x 10 -6 ). The distribution of Cd in a rice plant follows the following order in content: root>stem and leaves>brown rice>ear stalk>rice shell. Cd is mainly accumulated in rice root, taking 90% of the total amount of Cd contained in whole rice plant. The amount of Cd absorbed by rice increases with the amount of Cd applied to soil, though the total absorption extremely low, for example, only about 0.1% of the applied amount could be absorbed by two crops of rice, most of the applied Cd still retains in soil. Less and less Zn could be absorbed and utilized by rice along with the increase of the amount of the applied Cd. Application of Mn fertilizer affects negatively the absorption of Cd by rice, especially in brown rice

  6. A Survey on Optimal Signal Processing Techniques Applied to Improve the Performance of Mechanical Sensors in Automotive Applications

    Directory of Open Access Journals (Sweden)

    Wilmar Hernandez

    2007-01-01

    Full Text Available In this paper a survey on recent applications of optimal signal processing techniques to improve the performance of mechanical sensors is made. Here, a comparison between classical filters and optimal filters for automotive sensors is made, and the current state of the art of the application of robust and optimal control and signal processing techniques to the design of the intelligent (or smart sensors that today’s cars need is presented through several experimental results that show that the fusion of intelligent sensors and optimal signal processing techniques is the clear way to go. However, the switch between the traditional methods of designing automotive sensors and the new ones cannot be done overnight because there are some open research issues that have to be solved. This paper draws attention to one of the open research issues and tries to arouse researcher’s interest in the fusion of intelligent sensors and optimal signal processing techniques.

  7. Costs incurred by applying computer-aided design/computer-aided manufacturing techniques for the reconstruction of maxillofacial defects.

    Science.gov (United States)

    Rustemeyer, Jan; Melenberg, Alex; Sari-Rieger, Aynur

    2014-12-01

    This study aims to evaluate the additional costs incurred by using a computer-aided design/computer-aided manufacturing (CAD/CAM) technique for reconstructing maxillofacial defects by analyzing typical cases. The medical charts of 11 consecutive patients who were subjected to the CAD/CAM technique were considered, and invoices from the companies providing the CAD/CAM devices were reviewed for every case. The number of devices used was significantly correlated with cost (r = 0.880; p costs were found between cases in which prebent reconstruction plates were used (€3346.00 ± €29.00) and cases in which they were not (€2534.22 ± €264.48; p costs of two, three and four devices, even when ignoring the cost of reconstruction plates. Additional fees provided by statutory health insurance covered a mean of 171.5% ± 25.6% of the cost of the CAD/CAM devices. Since the additional fees provide financial compensation, we believe that the CAD/CAM technique is suited for wide application and not restricted to complex cases. Where additional fees/funds are not available, the CAD/CAM technique might be unprofitable, so the decision whether or not to use it remains a case-to-case decision with respect to cost versus benefit. Copyright © 2014 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

  8. X-diffraction technique applied for nano system metrology; Tecnica de difracao de raios X aplicada na metrologia de nanossistemas

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, Alexei Yu.; Machado, Rogerio; Robertis, Eveline de; Campos, Andrea P.C.; Archanjo, Braulio S.; Gomes, Lincoln S.; Achete, Carlos A., E-mail: okuznetsov@inmetro.gov.b [Instituto Nacional de Metrologia, Normalizacao e Qualidade Industrial (DIMAT/INMETRO), Duque de Caxias, RJ (Brazil). Div. de Metrologia de Materiais

    2009-07-01

    The application of nano materials are fast growing in all industrial sectors, with a strong necessity in nano metrology and normalizing in the nano material area. The great potential of the X-ray diffraction technique in this field is illustrated at the example of metals, metal oxides and pharmaceuticals

  9. Are U. S. Colleges and Universities Applying Marketing Techniques Properly and within the Context of an Overall Marketing Plan?

    Science.gov (United States)

    Goldgehn, Leslie A.

    1990-01-01

    A survey of 791 college admissions officers investigated the use and perceived effectiveness of 15 marketing techniques: publicity; target marketing; market segmentation; advertising; program development; market positioning; market research; access; marketing plan; pricing; marketing committee; advertising research; consultants; marketing audit;…

  10. Mobilisation of store Ca2+ activates tyrosine hydroxylase in bovine adrenal chromaffin cells

    International Nuclear Information System (INIS)

    McKenzie, S.; Marley, P.D.

    2001-01-01

    Full text: Many receptor agonists are able to activate tyrosine hydroxylase (TOH) in bovine adrenal chromaffin cells. The majority of these are dependent on extracellular Ca 2+ for this action. Entry of extracellular Ca 2+ through voltage-operated Ca 2+ channels is very effective at activating TOH. The contribution of the intracellular Ca 2+ stores to TOH activation however is not known. Previous studies have shown that mobilisation of intracellular Ca 2+ stores is effective at increasing phosphorylation of TOH, but its effect on TOH activity has not been studied. Therefore, in the present study, the effect of mobilisation of store Ca 2+ on TOH activity was investigated using primary cultures of bovine adrenal chromaffin cells. Cells were prepared from abattoir tissue and cultured for 3-6 days. TOH activity was determined over 10 minutes, measuring the 14 CO 2 produced following the hydroxylation and rapid decarboxylation of 14 C-tyrosine offered to intact cells. Caffeine increased TOH activity in a concentration-dependent manner with a maximum response of 100% increase at 20mM. This effect was not due to osmolarity since 20mM sucrose had no effect.Nor was it due to inhibition of phosphodiesterases, since the effect of caffeine was still seen in the presence of 1mM IBMX. However,caffeine-induced TOH activation was substantially reduced in the absence of extracellular Ca 2+ . The results suggest that TOH activity can be increased by mobilising intracellular Ca 2+ stores, but that this effect involves extracellular Ca 2+ influx, possibly through store-operated channels. Copyright (2001) Australian Neuroscience Society

  11. Metal mobilisation in hydrothermal sediments at the TAG Hydrothermal Field (MAR, 26°N)

    Science.gov (United States)

    Dutrieux, A. M.; Lichtschlag, A.; Martins, S.; Barriga, F. J.; Petersen, S.; Murton, B. J.

    2017-12-01

    Metalliferous sediments in the vicinity of hydrothermal systems are enriched in base metals, but few studies have addressed their potential as mineral resources. These metalliferous sediments have been accumulated by different processes and reflect modifications of the primary mineral deposits by: oxidation of the chimney materials, in situ precipitation of low-temperature minerals and mass wasting. To understand the post-formation processes in metalliferous sediments, we investigated sub-seafloor metal mobilisation in different geological environments. This presentation focuses on the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N) and explores sediment and pore water compositions using ICP-MS and ICP-OES. We use reactive transport modelling to interpret the degree of metal remobilisation and to identify the most important geochemical reactions in the different sediments. The pore water concentrations measured in sediments above inactive sulphide mounds present constant major elements composition that indicates this environment is dominated by complete exchange with seawater. The sediments, that are mainly composed of hematite and goethite formed during the oxidation of sulphides, have low Cu concentrations (sediments and capped by more recent sediment slumping. In the depositionary channels, pore waters show metal concentrations affected by diagenesis and redox-sensitive metals are released at depth (e.g. Mn2+ and Cu2+). The leaching of the primary sulphides (e.g. deprecated grains of chalcopyrite), and metal mobilisation lead to an enrichment of Cu and Zn at shallower depth. Here, some stratigraphic horizons scavenge metallic cations back into solid phases and form Mn-oxide crusts between 30 and 60 cm, in which Cu concentrations also increase. Our results demonstrate that metal mobilisation differs depending on the geological environment and their related accumulation processes, causing the absence of Cu on the top of inactive hydrothermal mounds but enriched

  12. Digital filtering techniques applied to electric power systems protection; Tecnicas de filtragem digital aplicadas a protecao de sistemas eletricos de potencia

    Energy Technology Data Exchange (ETDEWEB)

    Brito, Helio Glauco Ferreira

    1996-12-31

    This work introduces an analysis and a comparative study of some of the techniques for digital filtering of the voltage and current waveforms from faulted transmission lines. This study is of fundamental importance for the development of algorithms applied to digital protection of electric power systems. The techniques studied are based on the Discrete Fourier Transform theory, the Walsh functions and the Kalman filter theory. Two aspects were emphasized in this study: Firstly, the non-recursive techniques were analysed with the implementation of filters based on Fourier theory and the Walsh functions. Secondly, recursive techniques were analyzed, with the implementation of the filters based on the Kalman theory and once more on the Fourier theory. (author) 56 refs., 25 figs., 16 tabs.

  13. A synchronized particle image velocimetry and infrared thermography technique applied to convective mass transfer in champagne glasses

    Science.gov (United States)

    Beaumont, Fabien; Liger-Belair, Gérard; Bailly, Yannick; Polidori, Guillaume

    2016-05-01

    In champagne glasses, it was recently suggested that ascending bubble-driven flow patterns should be involved in the release of gaseous carbon dioxide (CO2) and volatile organic compounds. A key assumption was that the higher the velocity of the upward bubble-driven flow patterns in the liquid phase, the higher the volume fluxes of gaseous CO2 desorbing from the supersaturated liquid phase. In the present work, simultaneous monitoring of bubble-driven flow patterns within champagne glasses and gaseous CO2 escaping above the champagne surface was performed, through particle image velocimetry and infrared thermography techniques. Two quite emblematic types of champagne drinking vessels were investigated, namely a long-stemmed flute and a wide coupe. The synchronized use of both techniques proved that the cloud of gaseous CO2 escaping above champagne glasses strongly depends on the mixing flow patterns found in the liquid phase below.

  14. Community mobilisation in the 21st century: updating our theory of social change?

    Science.gov (United States)

    Campbell, Catherine

    2014-01-01

    The article explores the Freirian theory of social change underpinning health-related community mobilisation in poor and marginalised communities. Highlighting potential shortcomings of its essentialist understandings of power and identity, and linear notions of change, it examines how lessons from the 'new left', and burgeoning global protest movements, can rejuvenate the field given the growing complexity of 21st-century social inequalities. It suggests the need for a pastiche of approaches to accommodate health struggles in different times and places. However, while needing some updating, Freire's profound and actionable understandings of the symbolic and material dimensions of social inequalities remain a powerful starting point for activism.

  15. Complex investigation of extraction techniques applied for cyclitols and sugars isolation from different species of Solidago genus.

    Science.gov (United States)

    Ratiu, Ileana-Andreea; Al-Suod, Hossam; Ligor, Magdalena; Ligor, Tomasz; Railean-Plugaru, Viorica; Buszewski, Bogusław

    2018-03-15

    Cyclitols are phytochemicals naturally occurring in plant material, which attracted an increasing interest due to multiple medicinal attributes, among which the most important are the antidiabetic, antioxidant, and anticancer properties. Due to their valuable properties, sugars are used in the food industry as sweeteners, preservatives, texture modifiers, fermentation substrates, and flavoring and coloring agents. In this study, we report for the first time the quantitative analysis of sugars and cyclitols isolated from Solidago virgaurea L., which was used for the selection of the optimal solvent and extraction technique that can provide the best possible yield. Moreover, the quantities of sugars and cyclitols extracted from two other species, Solidago canadensis and Solidago gigantea, were investigated using the best extraction method and the most appropriate solvent. Comparative analysis of natural plant extracts obtained using five different techniques-maceration, Soxhlet extraction, pressurized liquid extraction, ultrasound-assisted extraction, and supercritical fluid extraction-was performed in order to decide the most suitable, efficient, and economically convenient extraction method. Three different solvents were used. Analysis of samples has been performed by solid-phase extraction for purification and pre-concentration, followed by derivation and GC-MS analysis. Highest efficiency for the total amount of obtained compounds has been reached by PLE, when water was used as a solvent. d-pinitol amount was almost similar for every solvent and for all the extraction techniques involved. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Technology Assessment of Dust Suppression Techniques Applied During Structural Demolition. Topical Report August1, 1995 - October 30, 1996

    International Nuclear Information System (INIS)

    Boudreaux, J.F.; Ebadian, M.A.; Williams, P.T.; Dua, S.K.

    1998-01-01

    Hanford, Fernald, Savannah River, and other sites are currently reviewing technologies that can be implemented to demolish buildings in a cost-effective manner. In order to demolish a structure properly and, at the same time, minimize the amount of dust generated from a given technology, an evaluation must be conducted to choose the most appropriate dust suppression technology given site-specific conditions. Thus, the purpose of this research, which was carried out at the Hemispheric Center for Environmental Technology (HCET) at Florida International University, was to conduct an experimental study of dust aerosol abatement (dust suppression) methods as applied to nuclear D and D. This experimental study targeted the problem of dust suppression during the demolition of nuclear facilities. The resulting data were employed to assist in the development of mathematical correlations that can be applied to predict dust generation during structural demolition

  17. Investigating the Impact of Carbon Tax to Power Generation in Java-Bali System by Applying Optimization Technique

    OpenAIRE

    Maxensius Tri Sambodo

    2010-01-01

    Java-Bali power system dominates the national installed capacity and will contribute to about 76% of the national CO2 emissions from the electricity sector in the future. Thus, minimizing CO2 emission from the Java-Bali system can help Indonesia to reduce the national CO2 emissions level. We apply optimization approach to investigate this problem by including carbon tax into the cost function. We analyzed data based on electricity generating system in 2008. In general the optimization showed ...

  18. Full Core modeling techniques for research reactors with irregular geometries using Serpent and PARCS applied to the CROCUS reactor

    International Nuclear Information System (INIS)

    Siefman, Daniel J.; Girardin, Gaëtan; Rais, Adolfo; Pautz, Andreas; Hursin, Mathieu

    2015-01-01

    Highlights: • Modeling of research reactors. • Serpent and PARCS coupling. • Lattice physics codes modeling techniques. - Abstract: This paper summarizes the results of modeling methodologies developed for the zero-power (100 W) teaching and research reactor CROCUS located in the Laboratory for Reactor Physics and Systems Behavior (LRS) at the Swiss Federal Institute of Technology in Lausanne (EPFL). The study gives evidence that the Monte Carlo code Serpent can be used effectively as a lattice physics tool for small reactors. CROCUS’ core has an irregular geometry with two fuel zones of different lattice pitches. This and the reactor’s small size necessitate the use of nonstandard cross-section homogenization techniques when modeling the full core with a 3D nodal diffusion code (e.g. PARCS). The primary goal of this work is the development of these techniques for steady-state neutronics and future transient neutronics analyses of not only CROCUS, but research reactors in general. In addition, the modeling methods can provide useful insight for analyzing small modular reactor concepts based on light water technology. Static computational models of CROCUS with the codes Serpent and MCNP5 are presented and methodologies are analyzed for using Serpent and SerpentXS to prepare macroscopic homogenized group cross-sections for a pin-by-pin model of CROCUS with PARCS. The most accurate homogenization scheme lead to a difference in terms of k eff of 385 pcm between the Serpent and PARCS model, while the MCNP5 and Serpent models differed in terms of k eff by 13 pcm (within the statistical error of each simulation). Comparisons of the axial power profiles between the Serpent model as a reference and a set of PARCS models using different homogenization techniques showed a consistent root-mean-square deviation of ∼8%, indicating that the differences are not due to the homogenization technique but rather arise from the definition of the diffusion coefficients

  19. The Development of an In-Situ TEM Technique for Studying Corrosion Behavior as Applied to Zirconium-Based Alloys

    Science.gov (United States)

    Harlow, Wayne

    Zirconium-based alloys are a commonly used material for nuclear fuel rod cladding, due to its low neutron cross section and good corrosion properties. However, corrosion is still a limiting factor in fuel rod lifespan, which restricts burn up levels, and thus efficiency, that can be achieved. While long-term corrosion behavior has been studied through both reactor and autoclave samples, the oxide nucleation and growth behavior has not been extensively studied. This work develops a new technique to study the initial stages of corrosion in zirconium-based alloys and the microstructural effects on this process by developing an environmental cell system for the TEM. Nanoscale oxidation parameters are developed, as is a new FIB technique to support this method. Precession diffraction is used in conjunction with in-situ TEM to observe the initial stages of corrosion in these alloys, and oxide thickness is estimated using low-loss EELS. In addition, the stress stabilization of tetragonal ZrO 2 is explored in the context of sample preparation for TEM. It was found that in-situ environmental TEM using an environmental cell replicates the oxidation behavior observed in autoclaved samples in both oxide structure and phases. Utilizing this technique, it was shown that cracking of the oxide layer in zirconium-based alloys is related to oxide relaxation, and not thermal changes. The effect of secondary phase particles on oxidation behavior did not present significant results, however a new method for studying initial oxidation rates using low-loss EELS was developed.

  20. Motion artifacts in functional near-infrared spectroscopy: a comparison of motion correction techniques applied to real cognitive data

    Science.gov (United States)

    Brigadoi, Sabrina; Ceccherini, Lisa; Cutini, Simone; Scarpa, Fabio; Scatturin, Pietro; Selb, Juliette; Gagnon, Louis; Boas, David A.; Cooper, Robert J.

    2013-01-01

    Motion artifacts are a significant source of noise in many functional near-infrared spectroscopy (fNIRS) experiments. Despite this, there is no well-established method for their removal. Instead, functional trials of fNIRS data containing a motion artifact are often rejected completely. However, in most experimental circumstances the number of trials is limited, and multiple motion artifacts are common, particularly in challenging populations. Many methods have been proposed recently to correct for motion artifacts, including principle component analysis, spline interpolation, Kalman filtering, wavelet filtering and correlation-based signal improvement. The performance of different techniques has been often compared in simulations, but only rarely has it been assessed on real functional data. Here, we compare the performance of these motion correction techniques on real functional data acquired during a cognitive task, which required the participant to speak aloud, leading to a low-frequency, low-amplitude motion artifact that is correlated with the hemodynamic response. To compare the efficacy of these methods, objective metrics related to the physiology of the hemodynamic response have been derived. Our results show that it is always better to correct for motion artifacts than reject trials, and that wavelet filtering is the most effective approach to correcting this type of artifact, reducing the area under the curve where the artifact is present in 93% of the cases. Our results therefore support previous studies that have shown wavelet filtering to be the most promising and powerful technique for the correction of motion artifacts in fNIRS data. The analyses performed here can serve as a guide for others to objectively test the impact of different motion correction algorithms and therefore select the most appropriate for the analysis of their own fNIRS experiment. PMID:23639260

  1. Nuclear techniques (PIXE and RBS) applied to analysis of pre hispanic metals of the Templo Mayor at Tenochtitlan

    International Nuclear Information System (INIS)

    Mendez U, I.; Tenorio, D.; Galvan, J.L.

    2000-01-01

    This work has the objective of determining by means of the utilization of nuclear techniques (PIXE and RBS) the composition and the alloy type of diverse aztec ornaments corresponding to Post classic period, they were manufactured principally with copper and gold such as bells, beads and disks; all they belonging at 9 oblations of Templo Mayor of Tenochtitlan. It is presented here briefly the historical and archaeological antecedents of the devices as well as the analytical methods for conclude with the results obtained. (Author)

  2. Applying monitoring, verification, and accounting techniques to a real-world, enhanced oil recovery operational CO2 leak

    Science.gov (United States)

    Wimmer, B.T.; Krapac, I.G.; Locke, R.; Iranmanesh, A.

    2011-01-01

    The use of carbon dioxide (CO2) for enhanced oil recovery (EOR) is being tested for oil fields in the Illinois Basin, USA. While this technology has shown promise for improving oil production, it has raised some issues about the safety of CO2 injection and storage. The Midwest Geological Sequestration Consortium (MGSC) organized a Monitoring, Verification, and Accounting (MVA) team to develop and deploy monitoring programs at three EOR sites in Illinois, Indiana, and Kentucky, USA. MVA goals include establishing baseline conditions to evaluate potential impacts from CO2 injection, demonstrating that project activities are protective of human health and the environment, and providing an accurate accounting of stored CO2. This paper focuses on the use of MVA techniques in monitoring a small CO2 leak from a supply line at an EOR facility under real-world conditions. The ability of shallow monitoring techniques to detect and quantify a CO2 leak under real-world conditions has been largely unproven. In July of 2009, a leak in the pipe supplying pressurized CO2 to an injection well was observed at an MGSC EOR site located in west-central Kentucky. Carbon dioxide was escaping from the supply pipe located approximately 1 m underground. The leak was discovered visually by site personnel and injection was halted immediately. At its largest extent, the hole created by the leak was approximately 1.9 m long by 1.7 m wide and 0.7 m deep in the land surface. This circumstance provided an excellent opportunity to evaluate the performance of several monitoring techniques including soil CO2 flux measurements, portable infrared gas analysis, thermal infrared imagery, and aerial hyperspectral imagery. Valuable experience was gained during this effort. Lessons learned included determining 1) hyperspectral imagery was not effective in detecting this relatively small, short-term CO2 leak, 2) even though injection was halted, the leak remained dynamic and presented a safety risk concern

  3. Use of Random and Site-Directed Mutagenesis to Probe Protein Structure-Function Relationships: Applied Techniques in the Study of Helicobacter pylori.

    Science.gov (United States)

    Whitmire, Jeannette M; Merrell, D Scott

    2017-01-01

    Mutagenesis is a valuable tool to examine the structure-function relationships of bacterial proteins. As such, a wide variety of mutagenesis techniques and strategies have been developed. This chapter details a selection of random mutagenesis methods and site-directed mutagenesis procedures that can be applied to an array of bacterial species. Additionally, the direct application of the techniques to study the Helicobacter pylori Ferric Uptake Regulator (Fur) protein is described. The varied approaches illustrated herein allow the robust investigation of the structural-functional relationships within a protein of interest.

  4. Neutrongraphy technique applied to the narcotics and terrorism enforcement; Neutrongrafia aplicada no combate ao narcotrafico e ao terrorismo

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Ademir X. da; Hacidume, Leo R.; Crispim, Verginia R. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia. Programa de Engenharia Nuclear

    1999-03-01

    Among the several methods of non-destructive essays that may be used for the detection of both drugs and explosives, the ones that utilize nuclear techniques have demonstrated to possess essential qualities for an efficient detection system. These techniques allow the inspection of a large quantity of samples fast, sensibly, specifically and with automatic decision, for they utilize radiation of great power of penetration. This work aims to show the neutron radiography and computed tomography potentiality for the detection of the drugs and explosives even when they are concealed by heavy materials. In the radiographic essays with thermal neutrons, samples of powder cocaine and explosives were inspected, concealed by several materials or not. The samples were irradiated during 30 minutes in the J-9 channel of the Argonauta research reactor of the IEN/CNEN in a neutron flux of 2:5 10{sup 5} n/cm{sup 2}.s. We used two sheets of gadolinium converter with a thickness of 25 {mu}m each one and a Kodak Industrex A5 photographic plaque. A comparative analysis among the tomographic images experimental and simulated obtained by X-ray, fast and thermal neutron is presented. The thermal neutron tomography demonstrate to be the best. (author)

  5. Artificial intelligence techniques applied to the development of a decision-support system for diagnosing celiac disease.

    Science.gov (United States)

    Tenório, Josceli Maria; Hummel, Anderson Diniz; Cohrs, Frederico Molina; Sdepanian, Vera Lucia; Pisa, Ivan Torres; de Fátima Marin, Heimar

    2011-11-01

    Celiac disease (CD) is a difficult-to-diagnose condition because of its multiple clinical presentations and symptoms shared with other diseases. Gold-standard diagnostic confirmation of suspected CD is achieved by biopsying the small intestine. To develop a clinical decision-support system (CDSS) integrated with an automated classifier to recognize CD cases, by selecting from experimental models developed using intelligence artificial techniques. A web-based system was designed for constructing a retrospective database that included 178 clinical cases for training. Tests were run on 270 automated classifiers available in Weka 3.6.1 using five artificial intelligence techniques, namely decision trees, Bayesian inference, k-nearest neighbor algorithm, support vector machines and artificial neural networks. The parameters evaluated were accuracy, sensitivity, specificity and area under the ROC curve (AUC). AUC was used as a criterion for selecting the CDSS algorithm. A testing database was constructed including 38 clinical CD cases for CDSS evaluation. The diagnoses suggested by CDSS were compared with those made by physicians during patient consultations. The most accurate method during the training phase was the averaged one-dependence estimator (AODE) algorithm (a Bayesian classifier), which showed accuracy 80.0%, sensitivity 0.78, specificity 0.80 and AUC 0.84. This classifier was integrated into the web-based decision-support system. The gold-standard validation of CDSS achieved accuracy of 84.2% and k=0.68 (pdiagnosis. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

  6. Teacher Formation in Super Learning Techniques Applied to the Teaching of the Mathematic in the Education Secondary

    Directory of Open Access Journals (Sweden)

    Avilner Rafael Páez Pereira

    2017-11-01

    Full Text Available The purpose of the study was to train LB "José Véliz" teacher for the teaching of mathematics through the application of super-learning techniques, based on the Research Participatory Action modality, proposed by López de Ceballos, (2008, following the model of the Lewin cycles of action (1946, quoted by Latorre (2007, based on the theories of humanism, Martínez (2009; multiple intelligence, Armstrong (2006; the Super learning of Sambrano and Stainer, (2003. Within the framework of the Critical - Social paradigm, in the type Qualitative Research, a plan of approach to the group was made, where through brainstorming and informal interviews the main problems were listed, which were hierarchized and then carried out an awareness - raising process. formulation of an overall plan of action. Among the results were 6 training workshops on techniques of breathing, relaxation, aromatherapy, music therapy, positive programming, color in the classroom, song in mathematical algorithms, in which processes of reflection were established on the benefits or obstacles obtained in the application of these in the transformation of the educational reality, elaborating a didactic strategy product of the experiences reached.

  7. Possible effects of mobilisation on acute post-operative pain and nociceptive function after total knee arthroplasty

    DEFF Research Database (Denmark)

    Lunn, T H; Kristensen, B B; Gaarn-Larsen, L

    2012-01-01

    anaesthesia and analgesia underwent an exercise (mobilisation) strategy on the first post-operative morning consisting of 25-m walking twice, with a 20-min interval. Pain was assessed at rest and during passive hip and knee flexion before, and 5 and 20 min after walk, as well as during walk. Nociceptive......BACKGROUND: Experimental studies in animals, healthy volunteers, and patients with chronic pain suggest exercise to provide analgesia in several types of pain conditions and after various nociceptive stimuli. To our knowledge, there is no data on the effects of exercise on pain and nociceptive...... function in surgical patients despite early mobilisation being an important factor to enhance recovery. We therefore investigated possible effects of mobilisation on post-operative pain and nociceptive function after total knee arthroplasty (TKA). METHODS: Thirty patients undergoing TKA under standardised...

  8. A magneto-optic technique for studying magnetization reversal processes and anisotropies applied to Co/Cu/Co trilayer structures

    Science.gov (United States)

    Daboo, C.; Bland, J. A. C.; Hicken, R. J.; Ives, A. J. R.; Baird, M. J.; Walker, M. J.

    1993-05-01

    We report the magnetization reversal and magnetic anisotropy behavior of ultrathin Co/Cu(111)/Co (dCu=20 and 27 Å) trilayer structures prepared by MBE on a 500-Å Ge/GaAs(110) epilayer. We describe an arrangement in which the magnetization components parallel and perpendicular to the applied field are both determined from longitudinal MOKE measurements. For the samples examined, coherent rotation of the magnetization vector is observed when the magnetic field is applied along the hard in-plane anisotropy axis, with the magnitude of the magnetization vector constant and close to its bulk value. Results of micromagnetic calculations closely reproduce the observed parallel and perpendicular magnetization loops, and yield strong uniaxial magnetic anisotropies in both layers while the interlayer coupling appears to be absent or negligible in comparison with the anisotropy strengths. An absence of antiferromagnetic (AF) coupling has been observed previously [W. F. Egelhoff, Jr. and M. T. Kief, Phys. Rev. B 45, 7795 (1992)] in contrast to recent results, indicating that AF coupling [M. T. Johnson et al., Phys. Rev. Lett. 69, 969 (1992)] and GMR [D. Grieg et al., J. Magn. Magn. Mater. 110, L239 (1992)] can occur in Co/Cu(111)/Co structures grown by MBE, but these properties are sensitively dependent on growth conditions. The absence of coupling in our samples is attributed to the presence of a significant interface roughness induced by the Ge epilayer. The uniaxial anisotropies are assumed to arise from strain or defects induced in the film.

  9. Determination of photocarrier density under continuous photoirradiation using spectroscopic techniques as applied to polymer: Fullerene blend films

    Energy Technology Data Exchange (ETDEWEB)

    Kanemoto, Katsuichi, E-mail: kkane@sci.osaka-cu.ac.jp; Nakatani, Hitomi; Domoto, Shinya [Department of Physics, Osaka City University, 3-3-138 Sugimoto, Sumiyoshi-ku, Osaka 558-8585 (Japan)

    2014-10-28

    We propose a method to determine the density of photocarrier under continuous photoirradiation in conjugated polymers using spectroscopic signals obtained by photoinduced absorption (PIA) measurements. The bleaching signals in the PIA measurements of polymer films and the steady-state absorption signals of oxidized polymer solution are employed to determine the photocarrier density. The method is applied to photocarriers of poly (3-hexylthiophene) (P3HT) in a blended film consisting of P3HT and [6,6]-phenyl C61 butyric acid methyl ester (PCBM). The photocarrier density under continuous photoirradiation of 580 mW/cm{sup 2} is determined to be 3.5 × 10{sup 16 }cm{sup −3}. Using a trend of the carrier density increasing in proportion to the square root of photo-excitation intensity, we provide a general formula to estimate the photocarrier density under simulated 1 sun solar irradiation for the P3HT: PCBM film of an arbitrary thickness. We emphasize that the method proposed in this study enables an estimate of carrier density without measuring a current and can be applied to films with no electrodes as well as to devices.

  10. Enhanced performance of CdS/CdTe thin-film devices through temperature profiling techniques applied to close-spaced sublimation deposition

    Energy Technology Data Exchange (ETDEWEB)

    Xiaonan Li; Sheldon, P.; Moutinho, H.; Matson, R. [National Renewable Energy Lab., Golden, CO (United States)

    1996-05-01

    The authors describe a methodology developed and applied to the close-spaced sublimation technique for thin-film CdTe deposition. The developed temperature profiles consisted of three discrete temperature segments, which the authors called the nucleation, plugging, and annealing temperatures. They have demonstrated that these temperature profiles can be used to grow large-grain material, plug pinholes, and improve CdS/CdTe photovoltaic device performance by about 15%. The improved material and device properties have been obtained while maintaining deposition temperatures compatible with commercially available substrates. This temperature profiling technique can be easily applied to a manufacturing environment by adjusting the temperature as a function of substrate position instead of time.

  11. Restoration of badlands through applying bio-engineering techniques in active gully systems: Evidence from the Ecuadorian Andes

    Science.gov (United States)

    Borja, P.; Vanacker, V.; Alvarado, D.; Govers, G.

    2012-04-01

    A better insight in the processes controlling sediment generation, transport and deposition in badlands is necessary to enhance restoration of degraded soils through eco-engineering techniques. In this study, we evaluate the effect of different bio-engineering measures on soil and slope stability. Five micro-catchments (of 0.2 to 5 ha) were selected within a 3 km2 area in the lower part of the Loreto catchment (Southern Ecuadorian Andes). The micro-catchments differ only by land cover and degree of implementation of soil and water conservation measures. Bio-engineering techniques were used to construct dikes made of fascines of wooden sticks and earth-filled tires in active gully beds, where they are most efficient to reduce water and sediment transport. The experimental design consists of three micro-catchments within highly degraded lands: (DI) micro-catchment with bio-engineering measures concentrated in the active gully beds, (DF) with reforestation of Eucalyptus trees, and (DT) reference situation without any conservation measures. Two micro-catchments were monitored in agricultural lands with (AI) and without (AT) bio-engineering measures in the active gully beds. All catchments were equipped with San Dimas flumes to measure water flow, and sediment traps to monitor sediment export. In the (active) gully beds, various parameters related to gully stability (soil water content, bed elevation, vegetation cover, sedimentation/erosion) were monitored at weekly intervals. First results show that bio-engineering techniques are efficient to stabilize active gully beds through a reduction of the rapid concentration of excess rainfall and the sediment production and transfer. Fascines made of wooden sticks are far more efficient than earth-filled tires. Sediment deposition behind dikes is strongly dependent on precedent rainfall events, and the slope and vegetation cover of the gully floor. The sediment deposited facilitates colonization of the gully floor by native

  12. Surgical manipulation compromises leukocyte mobilisation responses and inflammation after experimental cerebral ischaemia in mice

    Directory of Open Access Journals (Sweden)

    Adam eDenes

    2014-01-01

    Full Text Available Acute brain injury results in peripheral inflammatory changes, although the impact of these processes on neuronal death and neuroinflammation is currently unclear. To facilitate the translation of experimental studies to clinical benefit, it is vital to characterize the mechanisms by which acute brain injury induces peripheral inflammatory changes, and how these are affected by surgical manipulation in experimental models. Here we show that in mice, even mild surgical manipulation of extracranial tissues induced marked granulocyte mobilisation (300% and systemic induction of cytokines. However, intracranial changes induced by craniotomy, or subsequent induction of focal cerebral ischaemia were required to induce egress of CXCR2-positive granulocytes from the bone marrow. CXCR2 blockade resulted in reduced mobilisation of granulocytes from the bone marrow, caused an unexpected increase in circulating granulocytes, but failed to effect brain injury induced by cerebral ischaemia. We also demonstrate that isoflurane anaesthesia interferes with circulating leukocyte responses, which could contribute to the reported vascular and neuroprotective effects of isoflurane. In addition, no immunosuppression develops in the bone marrow after experimental stroke. Thus, experimental models of cerebral ischaemia are compromised by surgery and anaesthesia in proportion to the severity of surgical stress and overall tissue injury. Understanding the inherent confounding effects of surgical manipulation and development of new models of cerebral ischaemia with minimal surgical intervention could facilitate better understanding of interactions between inflammation and brain injury.

  13. Climate and enterprises: from mobilisation to action. Seven proposals to prepare the after-COP21

    International Nuclear Information System (INIS)

    Ayme, Arnaud; Derumaux, Quentin; Authier, Marc-Antoine; Monterno, Alexia de; Piolot, Lucie

    2015-11-01

    Based on meetings with 30 representatives of enterprises and institutions, this report first outlines that the COP21 takes place within a context characterised by a momentum which is to be exploited as awareness grows quickly, as data published by the IPCC is a consensus. It outlines that national climate contributions represent a positive methodological evolution and discusses the importance of bilateral agreements (example and the China-USA agreement), and gives an overview of remaining obstacles (financing the struggle against climate change, level playing field for European enterprises, how to support the losers of energy transition). The mobilisation of enterprises is then described as a new lever in the struggle against climate change: strong signals are sent by the financial sector; enterprises are facing many challenges. This mobilisation is presented as an unavoidable stake in negotiations. A necessary action of public authorities is outlined. Some proposals are stated regarding public financing of the struggle against climate change, the focussing of regulatory constraints on this struggle, public commissioning as a lever for a successful environmental transition, and the role of public authorities as a mediator between civil society and enterprises

  14. Advocacy, communication and social mobilisation for tuberculosis control in Pakistan: a qualitative case study.

    Science.gov (United States)

    Haq, Z; Khan, W; Rizwan, S

    2013-03-01

    A national-level study in four districts, one each in all four provinces of Pakistan, a high tuberculosis (TB) burden country. To examine how advocacy, communication and social mobilisation (ACSM) campaigns by the National Tuberculosis Programme (NTP) in Pakistan engaged the populations of interest, to what extent they were successful in promoting services and desired behaviours, and how these campaigns could be improved. This was a qualitative case study comprising 13 focus groups and 36 individual interviews in four districts. All three levels of the ACSM programme, i.e., planners, implementers and beneficiaries, were included among the respondents. Improved political commitment, availability of funds, partnership with the private sector, visibility of the NTP and access to directly observed treatment (DOT) were achieved. Individual and social environmental issues of poor patients and marginalised communities were addressed to some extent, and could be improved in the future. Empathy and respect from physicians, and better service delivery of the DOTS-based programme were desired by the patients. The strategic advocacy ensured political and financial commitment; however, identification and targeting of vulnerable populations, and carrying out context-based social mobilisation and effective counselling are crucial to increase the use of DOT. Evaluations should be built-in from the beginning to increase the evidence on effectiveness of ACSM campaigns.

  15. Improved general physical fitness of young swimmers by applying in the training process of endogenous hypoxic breathing techniques

    Directory of Open Access Journals (Sweden)

    Y.M. Furman

    2014-10-01

    Full Text Available Purpose : to examine the effect of general physical preparedness of young swimmers in the body artificially created state hypercapnic normobaric hypoxia. Material : the study involved 21 swimmer aged 13-14 years with sports qualifications at third and second sports categories. Results : the original method of working with young swimmers. Studies were conducted for 16 weeks a year preparatory period macrocycle. The average value of the index on the results of general endurance races 800m improved by 2.80 %. 8.24 % increased speed- strength endurance and 18.77 % increased dynamic strength endurance. During the period of formative experiment performance speed, agility, static endurance, flexibility and explosive strength athletes first experimental group was not significantly changed. Conclusions : it was found that the use of the proposed technique provides statistically significant increase in overall endurance, speed strength endurance and dynamic strength endurance.

  16. Judging complex movement performances for excellence: a principal components analysis-based technique applied to competitive diving.

    Science.gov (United States)

    Young, Cole; Reinkensmeyer, David J

    2014-08-01

    Athletes rely on subjective assessment of complex movements from coaches and judges to improve their motor skills. In some sports, such as diving, snowboard half pipe, gymnastics, and figure skating, subjective scoring forms the basis for competition. It is currently unclear whether this scoring process can be mathematically modeled; doing so could provide insight into what motor skill is. Principal components analysis has been proposed as a motion analysis method for identifying fundamental units of coordination. We used PCA to analyze movement quality of dives taken from USA Diving's 2009 World Team Selection Camp, first identifying eigenpostures associated with dives, and then using the eigenpostures and their temporal weighting coefficients, as well as elements commonly assumed to affect scoring - gross body path, splash area, and board tip motion - to identify eigendives. Within this eigendive space we predicted actual judges' scores using linear regression. This technique rated dives with accuracy comparable to the human judges. The temporal weighting of the eigenpostures, body center path, splash area, and board tip motion affected the score, but not the eigenpostures themselves. These results illustrate that (1) subjective scoring in a competitive diving event can be mathematically modeled; (2) the elements commonly assumed to affect dive scoring actually do affect scoring (3) skill in elite diving is more associated with the gross body path and the effect of the movement on the board and water than the units of coordination that PCA extracts, which might reflect the high level of technique these divers had achieved. We also illustrate how eigendives can be used to produce dive animations that an observer can distort continuously from poor to excellent, which is a novel approach to performance visualization. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Whole brain approaches for identification of microstructural abnormalities in individual patients: comparison of techniques applied to mild traumatic brain injury.

    Directory of Open Access Journals (Sweden)

    Namhee Kim

    Full Text Available Group-wise analyses of DTI in mTBI have demonstrated evidence of traumatic axonal injury (TAI, associated with adverse clinical outcomes. Although mTBI is likely to have a unique spatial pattern in each patient, group analyses implicitly assume that location of injury will be the same across patients. The purpose of this study was to optimize and validate a procedure for analysis of DTI images acquired in individual patients, which could detect inter-individual differences and be applied in the clinical setting, where patients must be assessed as individuals.After informed consent and in compliance with HIPAA, 34 mTBI patients and 42 normal subjects underwent 3.0 Tesla DTI. Four voxelwise assessment methods (standard Z-score, "one vs. many" t-test, Family-Wise Error Rate control using pseudo t-distribution, EZ-MAP for use in individual patients, were applied to each patient's fractional anisotropy (FA maps and tested for its ability to discriminate patients from controls. Receiver Operating Characteristic (ROC analyses were used to define optimal thresholds (voxel-level significance and spatial extent for reliable and robust detection of mTBI pathology.ROC analyses showed EZ-MAP (specificity 71%, sensitivity 71%, "one vs. many" t-test and standard Z-score (sensitivity 65%, specificity 76% for both methods resulted in a significant area under the curve (AUC score for discriminating mTBI patients from controls in terms of the total number of abnormal white matter voxels detected while the FWER test was not significant. EZ-MAP is demonstrated to be robust to assumptions of Gaussian behavior and may serve as an alternative to methods that require strict Gaussian assumptions.EZ-MAP provides a robust approach for delineation of regional abnormal anisotropy in individual mTBI patients.

  18. A technique for rapid source apportionment applied to ambient organic aerosol measurements from a thermal desorption aerosol gas chromatograph (TAG

    Directory of Open Access Journals (Sweden)

    Y. Zhang

    2016-11-01

    Full Text Available We present a rapid method for apportioning the sources of atmospheric organic aerosol composition measured by gas chromatography–mass spectrometry methods. Here, we specifically apply this new analysis method to data acquired on a thermal desorption aerosol gas chromatograph (TAG system. Gas chromatograms are divided by retention time into evenly spaced bins, within which the mass spectra are summed. A previous chromatogram binning method was introduced for the purpose of chromatogram structure deconvolution (e.g., major compound classes (Zhang et al., 2014. Here we extend the method development for the specific purpose of determining aerosol samples' sources. Chromatogram bins are arranged into an input data matrix for positive matrix factorization (PMF, where the sample number is the row dimension and the mass-spectra-resolved eluting time intervals (bins are the column dimension. Then two-dimensional PMF can effectively do three-dimensional factorization on the three-dimensional TAG mass spectra data. The retention time shift of the chromatogram is corrected by applying the median values of the different peaks' shifts. Bin width affects chemical resolution but does not affect PMF retrieval of the sources' time variations for low-factor solutions. A bin width smaller than the maximum retention shift among all samples requires retention time shift correction. A six-factor PMF comparison among aerosol mass spectrometry (AMS, TAG binning, and conventional TAG compound integration methods shows that the TAG binning method performs similarly to the integration method. However, the new binning method incorporates the entirety of the data set and requires significantly less pre-processing of the data than conventional single compound identification and integration. In addition, while a fraction of the most oxygenated aerosol does not elute through an underivatized TAG analysis, the TAG binning method does have the ability to achieve molecular level

  19. Comparison of partial least squares and lasso regression techniques as applied to laser-induced breakdown spectroscopy of geological samples

    International Nuclear Information System (INIS)

    Dyar, M.D.; Carmosino, M.L.; Breves, E.A.; Ozanne, M.V.; Clegg, S.M.; Wiens, R.C.

    2012-01-01

    A remote laser-induced breakdown spectrometer (LIBS) designed to simulate the ChemCam instrument on the Mars Science Laboratory Rover Curiosity was used to probe 100 geologic samples at a 9-m standoff distance. ChemCam consists of an integrated remote LIBS instrument that will probe samples up to 7 m from the mast of the rover and a remote micro-imager (RMI) that will record context images. The elemental compositions of 100 igneous and highly-metamorphosed rocks are determined with LIBS using three variations of multivariate analysis, with a goal of improving the analytical accuracy. Two forms of partial least squares (PLS) regression are employed with finely-tuned parameters: PLS-1 regresses a single response variable (elemental concentration) against the observation variables (spectra, or intensity at each of 6144 spectrometer channels), while PLS-2 simultaneously regresses multiple response variables (concentrations of the ten major elements in rocks) against the observation predictor variables, taking advantage of natural correlations between elements. Those results are contrasted with those from the multivariate regression technique of the least absolute shrinkage and selection operator (lasso), which is a penalized shrunken regression method that selects the specific channels for each element that explain the most variance in the concentration of that element. To make this comparison, we use results of cross-validation and of held-out testing, and employ unscaled and uncentered spectral intensity data because all of the input variables are already in the same units. Results demonstrate that the lasso, PLS-1, and PLS-2 all yield comparable results in terms of accuracy for this dataset. However, the interpretability of these methods differs greatly in terms of fundamental understanding of LIBS emissions. PLS techniques generate principal components, linear combinations of intensities at any number of spectrometer channels, which explain as much variance in the

  20. Comparison of partial least squares and lasso regression techniques as applied to laser-induced breakdown spectroscopy of geological samples

    Energy Technology Data Exchange (ETDEWEB)

    Dyar, M.D., E-mail: mdyar@mtholyoke.edu [Dept. of Astronomy, Mount Holyoke College, 50 College St., South Hadley, MA 01075 (United States); Carmosino, M.L.; Breves, E.A.; Ozanne, M.V. [Dept. of Astronomy, Mount Holyoke College, 50 College St., South Hadley, MA 01075 (United States); Clegg, S.M.; Wiens, R.C. [Los Alamos National Laboratory, P.O. Box 1663, MS J565, Los Alamos, NM 87545 (United States)

    2012-04-15

    A remote laser-induced breakdown spectrometer (LIBS) designed to simulate the ChemCam instrument on the Mars Science Laboratory Rover Curiosity was used to probe 100 geologic samples at a 9-m standoff distance. ChemCam consists of an integrated remote LIBS instrument that will probe samples up to 7 m from the mast of the rover and a remote micro-imager (RMI) that will record context images. The elemental compositions of 100 igneous and highly-metamorphosed rocks are determined with LIBS using three variations of multivariate analysis, with a goal of improving the analytical accuracy. Two forms of partial least squares (PLS) regression are employed with finely-tuned parameters: PLS-1 regresses a single response variable (elemental concentration) against the observation variables (spectra, or intensity at each of 6144 spectrometer channels), while PLS-2 simultaneously regresses multiple response variables (concentrations of the ten major elements in rocks) against the observation predictor variables, taking advantage of natural correlations between elements. Those results are contrasted with those from the multivariate regression technique of the least absolute shrinkage and selection operator (lasso), which is a penalized shrunken regression method that selects the specific channels for each element that explain the most variance in the concentration of that element. To make this comparison, we use results of cross-validation and of held-out testing, and employ unscaled and uncentered spectral intensity data because all of the input variables are already in the same units. Results demonstrate that the lasso, PLS-1, and PLS-2 all yield comparable results in terms of accuracy for this dataset. However, the interpretability of these methods differs greatly in terms of fundamental understanding of LIBS emissions. PLS techniques generate principal components, linear combinations of intensities at any number of spectrometer channels, which explain as much variance in the

  1. Artificial intelligence techniques applied to the development of a decision–support system for diagnosing celiac disease

    Science.gov (United States)

    Tenório, Josceli Maria; Hummel, Anderson Diniz; Cohrs, Frederico Molina; Sdepanian, Vera Lucia; Pisa, Ivan Torres; de Fátima Marin, Heimar

    2013-01-01

    Background Celiac disease (CD) is a difficult-to-diagnose condition because of its multiple clinical presentations and symptoms shared with other diseases. Gold-standard diagnostic confirmation of suspected CD is achieved by biopsying the small intestine. Objective To develop a clinical decision–support system (CDSS) integrated with an automated classifier to recognize CD cases, by selecting from experimental models developed using intelligence artificial techniques. Methods A web-based system was designed for constructing a retrospective database that included 178 clinical cases for training. Tests were run on 270 automated classifiers available in Weka 3.6.1 using five artificial intelligence techniques, namely decision trees, Bayesian inference, k-nearest neighbor algorithm, support vector machines and artificial neural networks. The parameters evaluated were accuracy, sensitivity, specificity and area under the ROC curve (AUC). AUC was used as a criterion for selecting the CDSS algorithm. A testing database was constructed including 38 clinical CD cases for CDSS evaluation. The diagnoses suggested by CDSS were compared with those made by physicians during patient consultations. Results The most accurate method during the training phase was the averaged one-dependence estimator (AODE) algorithm (a Bayesian classifier), which showed accuracy 80.0%, sensitivity 0.78, specificity 0.80 and AUC 0.84. This classifier was integrated into the web-based decision–support system. The gold-standard validation of CDSS achieved accuracy of 84.2% and k = 0.68 (p < 0.0001) with good agreement. The same accuracy was achieved in the comparison between the physician’s diagnostic impression and the gold standard k = 0. 64 (p < 0.0001). There was moderate agreement between the physician’s diagnostic impression and CDSS k = 0.46 (p = 0.0008). Conclusions The study results suggest that CDSS could be used to help in diagnosing CD, since the algorithm tested achieved excellent

  2. A technique for extraction and Thin Layer Chromatography visualization of fecal bile acids applied to neotropical felid scats

    Directory of Open Access Journals (Sweden)

    Ada Virginia Cazón Narvaez

    1999-06-01

    Full Text Available Fecal bile acid patterns have been used successfully to identify scats. Neotropical felid scats are capable of this biochemical identification because they present low concentrations of plant pigments that would interfere in fecal bile acids detection. However, neotropical felid scats have poor quantities of bile acids, so we developed in this work a proper technique for their extraction, visualization and determination. Twenty eighth feces of seven different felid species, collected from Zoological and Wildlife Parks, were dried and pulverized. The procedure for analyzing feces is : Take one g of pulverized feces and shake for 3 hr at room temperature in 20 ml benzene : methanol; filter and evaporate to 5 ml. Spot on TLC plate and develop in toluene :acetic acid:water. Dry and visualize with anisaldehyde. Field collected scats could be identified by the bile acids pattern revealed by this specific technique and ,then, used as a source of information for distribution, density and food habits studies.Los patrones de ácidos biliares fecales han sido utilizados satisfactoriamente para identificar heces. Las heces de félidos neotropicales son propicias para ser identificadas bioquímicamente, ya que contienen baja concentración de pigmentos vegetales que pudieran interferir en la detección de ácidos biliares. Sin embargo los ácidos biliares se encuentran en bajas concentraciones en las heces, por lo cual desarrollamos en este trabajo una técnica apropiada para su extracción, visualización y determinación. Veintiocho heces de diferentes félidos recolectadas de Zoológicos y Estaciones de Fauna Silvestre fueron secadas y pulverizadas. El procedimiento para analizar las heces es : Tomar un gramo de feca pulverizada y agitar en 20 ml de benceno :metanol a temperatura ambiente durante 3 hr ; luego filtrar y evaporar hasta 5 ml. Sembrar en placa de TLC y desarrollar en tolueno :ác. acético :agua. Secar y revelar con anisaldehído. Las heces

  3. Angular Multigrid Preconditioner for Krylov-Based Solution Techniques Applied to the Sn Equations with Highly Forward-Peaked Scattering

    Science.gov (United States)

    Turcksin, Bruno; Ragusa, Jean C.; Morel, Jim E.

    2012-01-01

    It is well known that the diffusion synthetic acceleration (DSA) methods for the Sn equations become ineffective in the Fokker-Planck forward-peaked scattering limit. In response to this deficiency, Morel and Manteuffel (1991) developed an angular multigrid method for the 1-D Sn equations. This method is very effective, costing roughly twice as much as DSA per source iteration, and yielding a maximum spectral radius of approximately 0.6 in the Fokker-Planck limit. Pautz, Adams, and Morel (PAM) (1999) later generalized the angular multigrid to 2-D, but it was found that the method was unstable with sufficiently forward-peaked mappings between the angular grids. The method was stabilized via a filtering technique based on diffusion operators, but this filtering also degraded the effectiveness of the overall scheme. The spectral radius was not bounded away from unity in the Fokker-Planck limit, although the method remained more effective than DSA. The purpose of this article is to recast the multidimensional PAM angular multigrid method without the filtering as an Sn preconditioner and use it in conjunction with the Generalized Minimal RESidual (GMRES) Krylov method. The approach ensures stability and our computational results demonstrate that it is also significantly more efficient than an analogous DSA-preconditioned Krylov method.

  4. A spatial model with pulsed releases to compare strategies for the sterile insect technique applied to the mosquito Aedes aegypti.

    Science.gov (United States)

    Oléron Evans, Thomas P; Bishop, Steven R

    2014-08-01

    We present a simple mathematical model to replicate the key features of the sterile insect technique (SIT) for controlling pest species, with particular reference to the mosquito Aedes aegypti, the main vector of dengue fever. The model differs from the majority of those studied previously in that it is simultaneously spatially explicit and involves pulsed, rather than continuous, sterile insect releases. The spatially uniform equilibria of the model are identified and analysed. Simulations are performed to analyse the impact of varying the number of release sites, the interval between pulsed releases and the overall volume of sterile insect releases on the effectiveness of SIT programmes. Results show that, given a fixed volume of available sterile insects, increasing the number of release sites and the frequency of releases increases the effectiveness of SIT programmes. It is also observed that programmes may become completely ineffective if the interval between pulsed releases is greater that a certain threshold value and that, beyond a certain point, increasing the overall volume of sterile insects released does not improve the effectiveness of SIT. It is also noted that insect dispersal drives a rapid recolonisation of areas in which the species has been eradicated and we argue that understanding the density dependent mortality of released insects is necessary to develop efficient, cost-effective SIT programmes. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

  5. Applying Information Retrieval Techniques to Detect Duplicates and to Rank References in the Preliminary Phases of Systematic Literature Reviews

    Directory of Open Access Journals (Sweden)

    Ramon Abilio

    2015-08-01

    Full Text Available Systematic Literature Review (SLR is a means to synthesize relevant and high quality studies related to a specific topic or research questions. In the Primary Selection stage of an SLR, the selection of studies is usually performed manually by reading title, abstract and keywords of each study. In the last years, the number of published scientific studies has grown increasing the effort to perform this sort of reviews. In this paper, we proposed strategies to detect non-papers and duplicated references in results exported by search engines, and strategies to rank the references in decreasing order of importance for an SLR, regarding the terms in the search string. These strategies are based on Information Retrieval techniques. We implemented the strategies and carried out an experimental evaluation of their applicability using two real datasets. As results, the strategy to detect non-papers presented 100% of precision and 50% of recall; the strategy to detect duplicates detected more duplicates than the manual inspection; and one of the strategies to rank relevant references presented 50% of precision and 80% of recall. Therefore, the results show that the proposed strategies can minimize the effort in the Primary Selection stage of an SLR.

  6. High-Speed Data Acquisition and Digital Signal Processing System for PET Imaging Techniques Applied to Mammography

    Science.gov (United States)

    Martinez, J. D.; Benlloch, J. M.; Cerda, J.; Lerche, Ch. W.; Pavon, N.; Sebastia, A.

    2004-06-01

    This paper is framed into the Positron Emission Mammography (PEM) project, whose aim is to develop an innovative gamma ray sensor for early breast cancer diagnosis. Currently, breast cancer is detected using low-energy X-ray screening. However, functional imaging techniques such as PET/FDG could be employed to detect breast cancer and track disease changes with greater sensitivity. Furthermore, a small and less expensive PET camera can be utilized minimizing main problems of whole body PET. To accomplish these objectives, we are developing a new gamma ray sensor based on a newly released photodetector. However, a dedicated PEM detector requires an adequate data acquisition (DAQ) and processing system. The characterization of gamma events needs a free-running analog-to-digital converter (ADC) with sampling rates of more than 50 Ms/s and must achieve event count rates up to 10 MHz. Moreover, comprehensive data processing must be carried out to obtain event parameters necessary for performing the image reconstruction. A new generation digital signal processor (DSP) has been used to comply with these requirements. This device enables us to manage the DAQ system at up to 80 Ms/s and to execute intensive calculi over the detector signals. This paper describes our designed DAQ and processing architecture whose main features are: very high-speed data conversion, multichannel synchronized acquisition with zero dead time, a digital triggering scheme, and high throughput of data with an extensive optimization of the signal processing algorithms.

  7. A review of fractional-order techniques applied to lithium-ion batteries, lead-acid batteries, and supercapacitors

    Science.gov (United States)

    Zou, Changfu; Zhang, Lei; Hu, Xiaosong; Wang, Zhenpo; Wik, Torsten; Pecht, Michael

    2018-06-01

    Electrochemical energy storage systems play an important role in diverse applications, such as electrified transportation and integration of renewable energy with the electrical grid. To facilitate model-based management for extracting full system potentials, proper mathematical models are imperative. Due to extra degrees of freedom brought by differentiation derivatives, fractional-order models may be able to better describe the dynamic behaviors of electrochemical systems. This paper provides a critical overview of fractional-order techniques for managing lithium-ion batteries, lead-acid batteries, and supercapacitors. Starting with the basic concepts and technical tools from fractional-order calculus, the modeling principles for these energy systems are presented by identifying disperse dynamic processes and using electrochemical impedance spectroscopy. Available battery/supercapacitor models are comprehensively reviewed, and the advantages of fractional types are discussed. Two case studies demonstrate the accuracy and computational efficiency of fractional-order models. These models offer 15-30% higher accuracy than their integer-order analogues, but have reasonable complexity. Consequently, fractional-order models can be good candidates for the development of advanced battery/supercapacitor management systems. Finally, the main technical challenges facing electrochemical energy storage system modeling, state estimation, and control in the fractional-order domain, as well as future research directions, are highlighted.

  8. Remotely controlled cutting techniques in the field of nuclear decommissioning. Overview of effectively applied thermal and non thermal cutting methods

    International Nuclear Information System (INIS)

    Bienia, H.

    2008-01-01

    Remote disassembly of radiologically burdened large components is among the most sophisticated and complex activities in the dismantling of nuclear installations. The required space for the technical equipment during the dismantling operations, especially for the removal of larger components is often an additional problem. Conventional cutting technologies like sawing with a disk saw or band saw require large and heavy frameworks as well as guiding systems with high rigidity. These solutions are expensive and sometimes not applicable. The essential question of all cutting and dismantling tasks is the physiological constitution of the component which will be dismantled. That means size, material and structure of the component. All these points are primarily technological questions. The last question is about the estimated costs of the used dismantling technology. Therefore following questions must be answered. How much are the investments for the cutting equipment itself and how much are the investments for the supporting equipment (e.g. necessary handling equipment)? Can I use this cutting equipment only for one special task or is it applicable for many tasks and therefore saves money because other cutting or dismantling technologies are dispensable? How long is the cutting time and what is the to control this technique required personnel? Four different cutting and dismantling technologies will be introduced and described. These four technologies differ in their principle of operation but all of them are used by cutting and dismantling tasks in nuclear power plants. (author)

  9. Environmental and traffic-related parameters affecting road dust composition: A multi-technique approach applied to Venice area (Italy)

    Science.gov (United States)

    Valotto, Gabrio; Rampazzo, Giancarlo; Visin, Flavia; Gonella, Francesco; Cattaruzza, Elti; Glisenti, Antonella; Formenton, Gianni; Tieppo, Paulo

    2015-12-01

    Road dust is a non-exhaust source of atmospheric particulate by re-suspension. It is composed of particles originating from natural sources as well as other non-exhaust source such as tire, brake and asphalt wear. The discrimination between atmospheric particles directly emitted from abrasion process and those related to re-suspension is therefore an open issue, as far as the percentage contribution of non-exhaust emissions is becoming more considerable due also to the recent policy actions and the technological upgrades in the automotive field, focused on the reduction of exhaust emissions. In this paper, road dust collected along the bridge that connects Venice (Italy) to the mainland is characterized with a multi-technique approach in order to determine its composition depending on environmental as well as traffic-related conditions. Six pollutant sources of road dust particles were identified by cluster analysis: brake, railway, tire, asphalt, soil + marine, and mixed combustions. Considering the lack of information on this matrix in this area, this study is intended to provide useful information for future identification of road dust re-suspension source in atmospheric particulate.

  10. DETERIORATION AND SOME OF APPLIED PRESERVATION TECHNIQUES FOR COMMON MUSHROOMS (AGARICUS BISPORUS, FOLLOWED BY LENTINUS EDODES, PLEUROTUS SPP.

    Directory of Open Access Journals (Sweden)

    Hamid Akbarirad

    2013-06-01

    Full Text Available Mushrooms are consider as a nutritional and health beneficial product. Three most cultivated mushrooms worldwide are Agaricus bisporus, Lentinus edodes and Pleurotus spp. Mushrooms are highly perishable. They tend to lose quality after harvest, mainly because of their high respiration rate and the fact that they have no barrier to protect them from water loss. Mushrooms’ shelf-life is limited to a few days under normal refrigeration conditions, which is a constraint on the distribution and marketing of fresh product, making extension of mushroom’s shelf life a constant quest. Modified atmosphere packaging provides an affordable packaging system that partly avoids enzymatic browning, fermentation and other biochemical processes by maintaining a controlled gas atmosphere. However, modified atmosphere packaging conditions should be carefully designed. Inappropriate modified atmosphere conditions may be ineffective or even shorten the shelf life of the product due to damage of tissues. Preservation techniques and specially use of MAP, specifically for Agaricus, Lentinus edodes and Pleurotus, is reviewed.

  11. Critical review of behaviour change techniques applied in intervention studies to improve cooking skills and food skills among adults.

    Science.gov (United States)

    Hollywood, Lynsey; Surgenor, Dawn; Reicks, Marla; McGowan, Laura; Lavelle, Fiona; Spence, Michelle; Raats, Monique; McCloat, Amanda; Mooney, Elaine; Caraher, Martin; Dean, Moira

    2017-08-21

    Cooking and food skills interventions have grown in popularity; however, there is a lack of transparency as to how these interventions were designed, highlighting a need to identify and understand the mechanisms of behavior change so that effective components may be introduced in future work. This study critiques cooking and food skills interventions in relation to their design, behavior change techniques (BCTs), theoretical underpinnings, and outcomes. A 40-item CALO-RE taxonomy was used to examine the components of 59 cooking and food skills interventions identified by two systematic reviews. Studies were coded by three independent coders. The three most frequently occurring BCTs identified were #1 Provide information on consequences of behavior in general; #21 Provide instruction on how to perform the behavior; and #26 Prompt Practice. Fifty-six interventions reported positive short-term outcomes. Only 14 interventions reported long-term outcomes containing BCTs relating to information provision. This study reviewed cooking and food skills interventions highlighting the most commonly used BCTs, and those associated with long-term positive outcomes for cooking skills and diet. This study indicates the potential for using the BCT CALO-RE taxonomy to inform the design, planning, delivery and evaluation of future interventions.

  12. Geostatistical and adjoint sensitivity techniques applied to a conceptual model of ground-water flow in the Paradox Basin, Utah

    International Nuclear Information System (INIS)

    Metcalfe, D.E.; Campbell, J.E.; RamaRao, B.S.; Harper, W.V.; Battelle Project Management Div., Columbus, OH)

    1985-01-01

    Sensitivity and uncertainty analysis are important components of performance assessment activities for potential high-level radioactive waste repositories. The application of geostatistical and adjoint sensitivity techniques to aid in the calibration of an existing conceptual model of ground-water flow is demonstrated for the Leadville Limestone in Paradox Basin, Utah. The geostatistical method called kriging is used to statistically analyze the measured potentiometric data for the Leadville. This analysis consists of identifying anomalous data and data trends and characterizing the correlation structure between data points. Adjoint sensitivity analysis is then performed to aid in the calibration of a conceptual model of ground-water flow to the Leadville measured potentiometric data. Sensitivity derivatives of the fit between the modeled Leadville potentiometric surface and the measured potentiometric data to model parameters and boundary conditions are calculated by the adjoint method. These sensitivity derivatives are used to determine which model parameter and boundary condition values should be modified to most efficiently improve the fit of modeled to measured potentiometric conditions

  13. New technique of insitu soil moisture sampling for environmental isotope analysis applied at 'Pilat-dune' near Bordeaux

    International Nuclear Information System (INIS)

    Thoma, G.; Esser, N.; Sonntag, C.; Weiss, W.; Rudolph, J.; Leveque, P.

    1978-01-01

    A new soil-air suction method with soil water vapor adsorption by 4 A-molecular sieve provides soil moisture samples from various depths for environmental isotope analysis and yields soil temperature profiles. A field tritium tracer experiment shows that this insitu sampling method has an isotope profile resolution of about 5-10 cm only. Application of this method in the Pilat sand dune (Bordeaux/France) yielded deuterium and tritium profiles down to 25 meters depth. Bomb tritium measurements of monthly lysimeter percolate samples available since 1961 show that the tritium response has a mean delay of 5 months in case of a sand lysimeter and of 2.5 years for a loess loam lysimeter. A simple HETP model simulates the layered downward movement of soil water and the longitudinal dispersion in the lysimeters. Field capacity and evapotranspiration taken as open parameters yield tritium concentration values of the lysimeters' percolate which are in close agreement with the experimental results. Based on local meteorological data the HETP model applied to tritium tracer experiments in the unsaturated zone further yiels an individual prediction of the momentary tracer position and of the soil moisture distribution. This prediction can be checked experimentally at selected intervals by coring. (orig.) [de

  14. Subsurface classification of objects under turbid waters by means of regularization techniques applied to real hyperspectral data

    Science.gov (United States)

    Carpena, Emmanuel; Jiménez, Luis O.; Arzuaga, Emmanuel; Fonseca, Sujeily; Reyes, Ernesto; Figueroa, Juan

    2017-05-01

    Improved benthic habitat mapping is needed to monitor coral reefs around the world and to assist coastal zones management programs. A fundamental challenge to remotely sensed mapping of coastal shallow waters is due to the significant disparity in the optical properties of the water column caused by the interaction between the coast and the sea. The objects to be classified have weak signals that interact with turbid waters that include sediments. In real scenarios, the absorption and backscattering coefficients are unknown with different sources of variability (river discharges and coastal interactions). Under normal circumstances, another unknown variable is the depth of shallow waters. This paper presents the development of algorithms for retrieving information and its application to the classification and mapping of objects under coastal shallow waters with different unknown concentrations of sediments. A mathematical model that simplifies the radiative transfer equation was used to quantify the interaction between the object of interest, the medium and the sensor. The retrieval of information requires the development of mathematical models and processing tools in the area of inversion, image reconstruction and classification of hyperspectral data. The algorithms developed were applied to one set of real hyperspectral imagery taken in a tank filled with water and TiO2 that emulates turbid coastal shallow waters. Tikhonov method of regularization was used in the inversion process to estimate the bottom albedo of the water tank using a priori information in the form of stored spectral signatures, previously measured, of objects of interest.

  15. Applying Multi-Criteria Decision Aiding Techniques in the Process of Project Management within the Wedding Planning Business

    Directory of Open Access Journals (Sweden)

    Dorota Górecka

    2012-01-01

    Full Text Available Numerous problems that emerge in the process of project management can be presented as multi-criteria issues and solved with the help of appropriate methods. The contracting authority, selecting one tender out of many available tenders, assesses them, taking into account various criteria, e.g. price, expected execution time and the contractor's experience. The owner of a company intending to purchase the fixed assets requisite for the realization of the project behaves similarly, i.e. the most advantageous model of the device is chosen, taking into account not only its price but also production capacity, energy intensity, noise emission, service availability, etc. From among many concepts, the investor has to choose a solution which frequently constitutes a compromise between price, functional properties, durability and aesthetics of performance, as well as safety of the utilization and impact on the environment. The choice of an investment location depends not only on the market, financial and supply factors, but also on so called soft factors such as the perceived quality of institutions and the attitude of local communities. All such situations can be described in the same way: taking into account preferences of the decision maker, the best possible choice must be made out of a finite set of alternatives evaluated according to a finite set of criteria. There are many different methods that can be used to aid a decision maker in this choice, including, but not limited to, techniques based on the outranking relation, verbal decision analysis and the MACBETH method. In this article, they will be compared and their applicability to different types of decision making problems will be considered. Furthermore, the PROMETHEE II method with a veto threshold will be presented within the text. Because the application of project management in the wedding planning business has gained wide popularity, as an illustrative example an empirical study of

  16. [Applying the Modified Delphi Technique to Develop the Role of HIV Case Managers and Essential Nursing Competencies in HIV Care].

    Science.gov (United States)

    Ko, Nai-Ying; Hsieh, Chia-Yin; Chen, Yen-Chin; Tsai, Chen-Hsi; Liu, Hsiao-Ying; Liu, Li-Fang

    2015-08-01

    Since 2005, the Taiwan Centers for Disease Control (Taiwan CDC) initiated an HIV case management program in AIDS-designated hospitals to provide integrative services and risk-reduction counseling for HIV-infected individuals. In light of the increasingly complex and highly specialized nature of clinical care, expanding and improving competency-based professional education is important to enhance the quality of HIV/AIDS care. The aim of this study was to develop the essential competency framework for HIV care for HIV case managers in Taiwan. We reviewed essential competencies of HIV care from Canada, the United Kingdom, and several African countries and devised descriptions of the roles of case managers and of the associated core competencies for HIV care in Taiwan. The modified Delphi technique was used to evaluate the draft framework of these roles and core competencies. A total of 15 HIV care experts were invited to join the expert panel to review and rank the draft framework. The final framework consisted of 7 roles and 27 competencies for HIV case managers. In Round 1, only 3 items did not receive consensus approval from the experts. After modification based on opinions of the experts, 7 roles and 27 competencies received 97.06% consensus approval in Round 2 and were organized into the final framework for HIV case managers. These roles and associated core competencies were: HIV Care Expert (9 competencies), Communicator (1 competency), Collaborator (4 competencies), Navigator (2 competencies), Manager (4 competencies), Advocate (2 competencies), and Professional (5 competencies). The authors developed an essential competency framework for HIV care using the consensus of a multidisciplinary expert panel. Curriculum developers and advanced nurses and practitioners may use this framework to support developments and to ensure a high quality of HIV care.

  17. Spatial variability of herbicide mobilisation and transport at catchment scale: insights from a field experiment

    Directory of Open Access Journals (Sweden)

    T. Doppler

    2012-07-01

    Full Text Available During rain events, herbicides can be transported from their point of application to surface waters, where they may harm aquatic organisms. Since the spatial pattern of mobilisation and transport is heterogeneous, the contributions of different fields to the herbicide load in the stream may vary considerably within one catchment. Therefore, the prediction of contributing areas could help to target mitigation measures efficiently to those locations where they reduce herbicide pollution the most.

    Such spatial predictions require sufficient insight into the underlying transport processes. To improve the understanding of the process chain of herbicide mobilisation on the field and the subsequent transport through the catchment to the stream, we performed a controlled herbicide application on corn fields in a small agricultural catchment (ca. 1 km2 with intensive crop production in the Swiss Plateau. Water samples were collected at different locations in the catchment (overland flow, tile drains and open channel for two months after application in 2009, with a high temporal resolution during rain events. We also analysed soil samples from the experimental fields and measured discharge, groundwater level, soil moisture and the occurrence of overland flow at several locations. Several rain events with varying intensities and magnitudes occurred during the study period. Overland flow and erosion were frequently observed in the entire catchment. Infiltration excess and saturation excess overland flow were both observed. However, the main herbicide loss event was dominated by infiltration excess.

    Despite the frequent and wide-spread occurrence of overland flow, most of this water did not reach the channel directly, but was retained in small depressions in the catchment. From there, it reached the stream via macropores and tile drains. Manholes of the drainage system and storm drains for road and farmyard runoff acted as

  18. Inspecting what you expect: Applying modern tools and techniques to evaluate the effectiveness of household energy interventions

    Science.gov (United States)

    Pillarisetti, Ajay

    Exposure to fine particles (PM2.5) resulting from solid fuel use for household energy needs - including cooking, heating, and lighting - is one of the leading causes of ill-health globally and is responsible for approximately 4 million premature deaths and 84 million lost disability-adjusted life years globally. The well-established links between cooking and ill-health are modulated by complex social, behavioral, technological, and environmental issues that pose unique challenges to efforts that seek to reduce this large health burden. Despite growing interest in the field - and numerous technical solutions that, in the laboratory at least, reduce emissions of harmful air pollutants from solid fuel combustion - there exists a need for refined tools, models, and techniques (1) for measuring environmental pollution in households using solid fuel, (2) for tracking adoption of interventions, and (3) for estimating the potential health benefits attributable to an intervention. Part of the need for higher spatial and temporal resolution data on particular concentrations and dynamics is being met by low-cost sensing platforms that provide large amounts of time-resolved data on critical parameters of interest, including PM2.5 concentrations and time-of-use metrics for heat-generating appliances, like stoves. Use of these sensors can result in non-trivial challenges, including those related to data management and analysis, and field logistics, but also enables novel lines of inquiry and insight. Chapter 2 presents a long-term deployment of real-time PM2.5 sensors in rural, solid-fuel-using kitchens, specifically seeking to evaluate how well commonly measured 24 or 48-hour samples represent long-term means. While short-term measures were poor predictors of long-term means, the dataset enabled evaluation of numerous sampling strategies - including sampling once per week, month, or season - that had much lower errors and higher probabilities of estimating the true mean

  19. Effects of experimental acidification on mobilisation of metals from sediments of limed and non-limed lakes

    International Nuclear Information System (INIS)

    Waellstedt, Teresia; Borg, Hans

    2003-01-01

    In order to study the influence of pH on the mobilisation of metals from lake sediments, intact sediment cores with overlying water were sampled from one lime treated lake and one acidified lake. The overlying water of two cores from each lake was successively acidified to pH 4.2 over a period of 3 months. In the acid treated samples from the limed lake, the initial concentrations of Al, Cd, Mn, Pb and Zn in the overlying water were generally lower and the final concentrations were higher than in the acid treated samples from the acidified lake. The labile inorganic fraction of Al (Al i ) was increasingly dominating as pH decreased. Redox potential and pH in the sediment indicated that the upper two centimetres were involved in the exchange reactions. The experiment showed that mobilisation of metals from sediments can occur and the results indicated that mobilisation could contribute to increased concentrations of metals in lake water during reacidification of formerly lime treated lakes. - Reacidification leads to mobilisation of metals from lake sediments

  20. The de Bono LAMS Sequence Series: Template Designs as Knowledge-Mobilising Strategy for 21st Century Higher Education

    Science.gov (United States)

    Dobozy, Eva

    2012-01-01

    In this paper, the five interlocking de Bono LAMS sequences are introduced as a new form of generic template designs. This transdisciplinary knowledge-mobilising strategy is based on Edward de Bono's attention-directing ideas and thinking skills, commonly known as the CoRT tools. The development of the de Bono LAMS sequence series is an important…

  1. Overseas Voter Mobilisation in Singapore: Implications from Malaysia’s 13th General Election

    Directory of Open Access Journals (Sweden)

    James Gomez

    2013-01-01

    Full Text Available This paper discusses voter mobilisation and other election-related activities of Malaysian voters living, studying and working in Singapore in the context of Malaysia’s 13th general election (GE13. According to the World Bank, nearly 400,000 Malaysians reside in the city-state. Thus these figures represent a significant Malaysian voter pool based in Singapore. Efforts to mobilise these voters for general elections or other causes have political implications for both countries, which became apparent following Singapore-based Malaysians’ activities to encourage Malaysians to return home to cast their votes during the 13th general election. Singapore’s strict public assembly laws led to several legal issues related to the voter mobilisation and election campaign activities undertaken by Malaysians in the city-state. These legal issues became a source of friction between the two countries during the elections as government leaders and authorities on both sides of the causeway accused the other of interfering in domestic political matters. Given the growing number of Malaysians in Singapore and the likely repeat of Malaysian voter mobilisation activities in Singapore in the run-up to the fourteenth general election (GE14 in 2018, issues related to the election activities of Malaysian voters in Singapore stand to be another set of factors that will shape the health of bilateral relations between these two countries.

  2. Mobilisation of heavy metals into the urine by CaEDTA: relation to erythrocyte and plasma concentrations and exposure indicators.

    Science.gov (United States)

    Araki, S; Aono, H; Murata, K

    1986-09-01

    To investigate the effects of calcium disodium ethylenediamine tetra-acetate (CaEDTA) on the urinary excretion, erythrocyte, and plasma concentrations and exposure indicators of seven heavy metals, CaEDTA was administered by intravenous infusion to 20 workers exposed to lead, zinc, and copper. The workers' blood lead concentrations ranged from 22 to 59 micrograms/dl (mean 38 micrograms/dl (1.8 mumol/l]. The 24 hour urinary excretion of metals after CaEDTA administration (mobilisation yield) was on average 13 times the background excretion for lead, 11 times for zinc, 3.8 times for manganese, 3.4 times for cadmium, 1.3 times for copper, and 1.1 times for chromium; no significant increase was found for mercury. The mobilisation yield of lead (MPb) was significantly correlated with whole blood and erythrocyte concentrations and the urinary excretion of lead but not with its plasma concentration; similarly, the mobilisation yield of cadmium was significantly correlated with its erythrocyte concentration. In addition, MPb was significantly correlated with intra-erythrocytic enzyme delta-aminolaevulinic acid dehydratase activity and urinary coproporphyrin excretion. The relation between the mobilisation yield of heavy metals and their body burden (and toxic signs) is discussed in the light of these findings.

  3. Materials mobilised by the French economy: a decrease stabilised since the crisis of 2008

    International Nuclear Information System (INIS)

    Calatayud, Philippe

    2016-05-01

    This publication proposes data illustrating the evolution of the use of natural resources, and more particularly materials mobilised by the French economy and population since 1990. The evolution of domestic material consumption is described through that of domestic extraction, and of imports and exports, through the apparent and global material consumption in 2013, and the evolution of apparent domestic material consumption, and of the quantity of materials extracted from the French territory, imported or exported. Tables indicate these evolutions since 1990 for the different materials (biomass, wood, metallic ores, minerals used in construction or industry, coal, oil, natural gas, products based on fossil fuels). The rate between hidden flows and apparent flows is shown to be steady. It is also outlined that the recession has intensified material productivity but decreased material consumption per inhabitant. This material consumption per inhabitant is compared with that of European and non-European countries

  4. Domestic saving mobilisation and small business creation: The case of Cameroon

    Directory of Open Access Journals (Sweden)

    LC Forje

    2014-07-01

    Full Text Available Promoting savings and providing a basis for lending to the poor is a growing concern in many developing countries. Cameroon has a culture of savings mobilisation known as njangi/tontine. The njangi is contributions given to members in a rotating form at the end of every sitting, and tontine is voluntary savings held by the group. This study reveals that njangi/tontine groups only lend money to group members and suggests that a micro village bank known as MC2 could be used as guarantor to ensure that group monies lent to non-group members are repaid. Encouragement and improvement in the function of such voluntary savings could promote the creation of small businesses in the country.  The Cameroonian government needs to improve fighting corruption and a functional justice system to ensure security.

  5. Rosuvastatin reduces atherosclerotic lesions and promotes progenitor cell mobilisation and recruitment in apolipoprotein E knockout mice.

    Science.gov (United States)

    Schroeter, Marco R; Humboldt, Tim; Schäfer, Katrin; Konstantinides, Stavros

    2009-07-01

    Statins enhance incorporation of bone marrow-derived cells into experimental neointimal lesions. However, the contribution of progenitor cells to progression of spontaneous atherosclerotic plaques, and the possible modulatory role of statins in this process, remain poorly understood. We compared the effects of rosuvastatin (1 and 10mg/kg BW) and pravastatin (10mg/kg) on progenitor cell mobilisation, recruitment into atherosclerotic plaques, and lesion growth. Statins were administered over 8 weeks to apolipoprotein E knockout mice on atherogenic diet. In addition, mice were lethally irradiated, followed by transplantation of bone marrow from LacZ transgenic mice. Rosuvastatin reduced lesion area and intima-to-media ratio at the brachiocephalic artery compared to vehicle, while both parameters were not significantly altered by pravastatin. Rosuvastatin also augmented endothelialisation (P<0.05) and reduced the smooth muscle cells (SMC) content (P=0.042) of lesions. Numbers of c-kit, sca-1 and flk-1, sca-1 double-positive progenitor cells were significantly increased in rosuvastatin compared to control-treated mice, both in the bone marrow and the peripheral blood. Similarly, the number of spleen-derived acLDL, lectin double-positive progenitor cells (P=0.001) and colony-forming units (P=0.0104) was significantly increased in mice treated with rosuvastatin compared to vehicle alone. In the bone marrow, increased Akt and p42/44 MAP kinase phosphorylation and upregulated SDF1alpha mRNA expression were observed. Importantly, rosuvastatin treatment also increased the plasma levels of c-kit ligand (P=0.003), and the number of c-kit-positive cells within atherosclerotic lesions (P=0.041). Our findings suggest that rosuvastatin reduces the size of atherosclerotic plaques, and this effect appears to involve progenitor cell mobilisation and recruitment into vascular lesions.

  6. Nuclear energy: from scientist mobilisation to the rise of counter-expertise

    International Nuclear Information System (INIS)

    Topcu, Sezin

    2006-01-01

    The management of nuclear energy in France was restricted until the mid 1970's to a small circle of government experts. Within the scientific community criticism against nuclear power mostly targeted nuclear weapons while the sphere of civil nuclear energy remained unchallenged. The launch of the French nuclear programme in 1974 led to the first protest against civil nuclear power and its management within the scientific community. The mobilisation of thousands of researchers against the programme, initially through a petition, the so-called 'Appeal of the 400', then through the creation of an association, the 'Group of Scientists for Information on Nuclear Energy (GSIEN)', beside reflecting a rupture in the relations with science, progress and decision-making processes in the nuclear field, also expressed in the following decades the appropriation of critical knowledge on nuclear risks by the actors of non-governmental organisations. The criticism raised by scientists in 1975 therefore underlies two major shifts between the 1950's to 1990's in collective action vis-a-vis nuclear risk: from the mobilisation of 'distinguished scientists' against the atom bomb in the 1950's and 1960's (Joliot, Russell, Einstein, Rostand) to the politicisation of nuclear power by 'critical scientists' in the post-May 1968 period (GSIEN) and finally, after the Chernobyl accident, to the rise of associations of counter-expertise on nuclear energy (creation of expert NGOs such as the Commission for Independent Research and Information on Radioactivity-CRIIRAD and the Association for the Control of Radioactivity in the West-ACRO). This paper examines the crucial role that the community of physicists has played in transforming the relations between scientists, science, expertise and society

  7. Nuclear techniques applied to provenance and technological studies of Renaissance majolica roundels from Portuguese museums attributed to della Robbia Italian workshop

    International Nuclear Information System (INIS)

    Dias, M.I.; Prudencio, M.I.; Kasztovszky, Zsolt; Maroti, Boglarka; Harsanyi, Ildiko

    2017-01-01

    Artistic and historical examination of high-quality glazed terracotta sculptures displayed in various Portuguese museums point to their production in della Robbia workshop of Florence (Italy). A multitechnique analytical approach is applied for the first time to these sculptures, aiming to confirm their origin. Materials were analyzed using Instrumental Neutron Activation Analysis, Prompt Gamma Activation Analysis and X-ray Diffraction. The compositional results are similar to other della Robbia sculptures, suggesting a common origin for the raw material that was identified as carbonate rich marine origin marly clay. The applied firing temperatures was proved to be around 900 deg C. The differences found within each sculpture are explained by the production technique of assembling separate parts to produce these huge sculptures, and the clay pit heterogeneity. (author)

  8. Magnetically applied pressure-shear : a new technique for direct strength measurement at high pressure (final report for LDRD project 117856).

    Energy Technology Data Exchange (ETDEWEB)

    Lamppa, Derek C.; Haill, Thomas A.; Alexander, C. Scott; Asay, James Russell

    2010-09-01

    A new experimental technique to measure material shear strength at high pressures has been developed for use on magneto-hydrodynamic (MHD) drive pulsed power platforms. By applying an external static magnetic field to the sample region, the MHD drive directly induces a shear stress wave in addition to the usual longitudinal stress wave. Strength is probed by passing this shear wave through a sample material where the transmissible shear stress is limited to the sample strength. The magnitude of the transmitted shear wave is measured via a transverse VISAR system from which the sample strength is determined.

  9. The range of excursion of flexor tendons in Zone V: a comparison of active vs passive flexion mobilisation regimes.

    LENUS (Irish Health Repository)

    Panchal, J

    1997-10-01

    A number of early postoperative mobilisation regimes have been developed in an attempt to increase tendon excursion and gliding and thereby reduce formation of adhesions following repair of flexor tendons. Early active flexion mobilisation regimes are becoming more popular, and have replaced early passive flexion regimes in many centres. The aim of the present study was: (a) to determine the range of excursion of flexor tendons in Zone V, and (b) to compare the excursion ranges between active (Belfast) and passive (modified Duran) flexion mobilisation regimes postoperatively. This was done (a) in two cadavers, and (b) in two patients intraoperatively, and postoperatively at 10 days, 3 weeks and 6 weeks. With passive flexion, the mean tendon excursion in Zone V in cadavers was 1 mm for flexor digitorum superficialis (FDS), flexor digitorum profundus (FDP) and flexor pollicis longus (FPL) tendons respectively. With simulated active flexion, the mean tendon excursion was 14 mm, 10 mm and 11 mm respectively. The mean tendon excursion in clinical cases intraoperatively following passive flexion was 2 mm for FDS, FDP and FPL respectively; following simulated active flexion it was 10 mm, 11 mm and 11 mm for FDS, FDP and FPL respectively. On the tenth day following repair, the mean excursions of FDS, FDP and FPL were 1 mm, 4 mm and 4 mm on passive flexion as compared to 3 mm, 10 mm and 12 mm on active flexion respectively. Three weeks postoperatively, the mean excursions of FDS, FDP and FPL tendons were 1 mm, 2 mm and 1 mm on passive flexion as compared to 5 mm, 15 mm on active flexion respectively. Six weeks postoperatively, the mean excursions of FDS, FDP and FPL tendons were 9 mm, 7 mm and 4 mm on passive flexion as compared to 12 mm, 33 mm and 20 mm on active flexion respectively. These results demonstrate an increased excursion of repaired flexor tendons in Zone V following an active flexion mobilisation regime as compared to a passive flexion mobilisation regime.

  10. Improving optical properties of silicon nitride films to be applied in the middle infrared optics by a combined high-power impulse/unbalanced magnetron sputtering deposition technique.

    Science.gov (United States)

    Liao, Bo-Huei; Hsiao, Chien-Nan

    2014-02-01

    Silicon nitride films are prepared by a combined high-power impulse/unbalanced magnetron sputtering (HIPIMS/UBMS) deposition technique. Different unbalance coefficients and pulse on/off ratios are applied to improve the optical properties of the silicon nitride films. The refractive indices of the Si3N4 films vary from 2.17 to 2.02 in the wavelength ranges of 400-700 nm, and all the extinction coefficients are smaller than 1×10(-4). The Fourier transform infrared spectroscopy and x-ray diffractometry measurements reveal the amorphous structure of the Si3N4 films with extremely low hydrogen content and very low absorption between the near IR and middle IR ranges. Compared to other deposition techniques, Si3N4 films deposited by the combined HIPIMS/UBMS deposition technique possess the highest refractive index, the lowest extinction coefficient, and excellent structural properties. Finally a four-layer coating is deposited on both sides of a silicon substrate. The average transmittance from 3200 to 4800 nm is 99.0%, and the highest transmittance is 99.97% around 4200 nm.

  11. Usage of laser techniques and digital aerial coverage as a layer for as-built applied to the LPG pipeline Urucu-Coari right-of-way

    Energy Technology Data Exchange (ETDEWEB)

    Furquim, Antonio J. [ESTEIO Engenharia e Aerolevantamentos S.A, Curitiba, PR (Brazil)

    2009-07-01

    The usage of taking of digital aerial images is a reality worldwide, but in Brazil there is few sensors in use available, which makes recognize the pioneer aspect of the technique. Something similar also occurs with the airborne LASER scanning, whose technique has been applied for more time, used in the obtaining of digital terrain models. The use of digital imaging along with the LASER survey can offer an option for the generation of high quality products in a very fast and efficient way, aiming at numberless applications. Among such applications, the generation of cartographic products for the implantation of pipelines, as well as the as-built drawings of these same rights-of-ways after the implantation can be highlighted. The pipeline sector has been the focus of great investments and keeps on presenting demand for new projects and implantations. That allows to deduce that the speed in the generation of accurate bases for such purpose shall progress towards the continuous development of such aerial survey techniques. This paper presents the application of images and LASER survey to obtain ortho photos of Urucu-Coari liquefied petroleum gas (LPG) pipeline. (author)

  12. Dutch Young Adults Ratings of Behavior Change Techniques Applied in Mobile Phone Apps to Promote Physical Activity: A Cross-Sectional Survey.

    Science.gov (United States)

    Belmon, Laura S; Middelweerd, Anouk; Te Velde, Saskia J; Brug, Johannes

    2015-11-12

    Interventions delivered through new device technology, including mobile phone apps, appear to be an effective method to reach young adults. Previous research indicates that self-efficacy and social support for physical activity and self-regulation behavior change techniques (BCT), such as goal setting, feedback, and self-monitoring, are important for promoting physical activity; however, little is known about evaluations by the target population of BCTs applied to physical activity apps and whether these preferences are associated with individual personality characteristics. This study aimed to explore young adults' opinions regarding BCTs (including self-regulation techniques) applied in mobile phone physical activity apps, and to examine associations between personality characteristics and ratings of BCTs applied in physical activity apps. We conducted a cross-sectional online survey among healthy 18 to 30-year-old adults (N=179). Data on participants' gender, age, height, weight, current education level, living situation, mobile phone use, personality traits, exercise self-efficacy, exercise self-identity, total physical activity level, and whether participants met Dutch physical activity guidelines were collected. Items for rating BCTs applied in physical activity apps were selected from a hierarchical taxonomy for BCTs, and were clustered into three BCT categories according to factor analysis: "goal setting and goal reviewing," "feedback and self-monitoring," and "social support and social comparison." Most participants were female (n=146), highly educated (n=169), physically active, and had high levels of self-efficacy. In general, we observed high ratings of BCTs aimed to increase "goal setting and goal reviewing" and "feedback and self-monitoring," but not for BCTs addressing "social support and social comparison." Only 3 (out of 16 tested) significant associations between personality characteristics and BCTs were observed: "agreeableness" was related to

  13. Engagement militant et politisation des mobilisations au sein des oppositions urbaines à Istanbul

    Directory of Open Access Journals (Sweden)

    Clémence Petit

    2011-07-01

    Full Text Available La Municipalité du Grand Istanbul met en œuvre depuis quelques années une « politique de transformation urbaine » pour faire d’Istanbul une ville moderne et compétitive sur la scène mondiale. Les mobilisations locales et les mouvements protestataires se multiplient pour infléchir une politique qui domine aujourd’hui l’agenda urbain « néolibéral » et empêcher les démolitions et déplacements de population escomptés. Au-delà de la distance au politique généralement affichée – condition de légitimité dans le système sécuritaire mis en place en Turquie après le coup d’État de 1980 – ces « oppositions urbaines » sont traversées par des débats sur la place du politique dans la mobilisation. À partir de l’étude sociologique de deux associations de quartiers et de deux mouvements de « professionnels urbains », cette contribution analyse le travail de définition des cadrages et répertoires d’action propres à chaque mouvement. Elle fait apparaître le rôle de ces professionnels urbains dans la requalification politique du désaccord qui divise les oppositions urbaines entre une stratégie « experte » et une stratégie plus politique. L’analyse met néanmoins en évidence le caractère dynamique et relatif – en termes de contextes et d’échelles – des stratégies d’appropriation des politiques publiques locales et des processus de politisation des « mouvements urbains ».The Istanbul Greater Municipality has been implementing for a few years numerous ‘urban renewal projects’ to change Istanbul into a modern and competitive city on the global scene. Reacting to the demolitions and evictions of entire neighbourhoods caused by these projects, some inhabitants and ‘urban professionals’ mobilize within new movements and neighbourdhood associations. Beyond the distance they usually show towards politics – a condition of legitimacy in the securitarian system introduced in

  14. AN ACCURACY ASSESSMENT OF GEOREFERENCED POINT CLOUDS PRODUCED VIA MULTI-VIEW STEREO TECHNIQUES APPLIED TO IMAGERY ACQUIRED VIA UNMANNED AERIAL VEHICLE

    Directory of Open Access Journals (Sweden)

    S. Harwin

    2012-08-01

    Full Text Available Low-cost Unmanned Aerial Vehicles (UAVs are becoming viable environmental remote sensing tools. Sensor and battery technology is expanding the data capture opportunities. The UAV, as a close range remote sensing platform, can capture high resolution photography on-demand. This imagery can be used to produce dense point clouds using multi-view stereopsis techniques (MVS combining computer vision and photogrammetry. This study examines point clouds produced using MVS techniques applied to UAV and terrestrial photography. A multi-rotor micro UAV acquired aerial imagery from a altitude of approximately 30–40 m. The point clouds produced are extremely dense (<1–3 cm point spacing and provide a detailed record of the surface in the study area, a 70 m section of sheltered coastline in southeast Tasmania. Areas with little surface texture were not well captured, similarly, areas with complex geometry such as grass tussocks and woody scrub were not well mapped. The process fails to penetrate vegetation, but extracts very detailed terrain in unvegetated areas. Initially the point clouds are in an arbitrary coordinate system and need to be georeferenced. A Helmert transformation is applied based on matching ground control points (GCPs identified in the point clouds to GCPs surveying with differential GPS. These point clouds can be used, alongside laser scanning and more traditional techniques, to provide very detailed and precise representations of a range of landscapes at key moments. There are many potential applications for the UAV-MVS technique, including coastal erosion and accretion monitoring, mine surveying and other environmental monitoring applications. For the generated point clouds to be used in spatial applications they need to be converted to surface models that reduce dataset size without loosing too much detail. Triangulated meshes are one option, another is Poisson Surface Reconstruction. This latter option makes use of point normal

  15. How to Apply the User Profile Usability Technique in the User Modelling Activity for an Adaptive Food Recommendation System for People on Special Diets

    Directory of Open Access Journals (Sweden)

    Lucrecia Llerena

    2017-10-01

    Full Text Available Interest among software professionals in the possibility of adapting software to user requirements has grown as a result of the evolution of software analysis, design and implementation thinking and the growth in the number of software systems users. Moving away from the traditional approach where the user has to settle for the options offered by software systems, different factors (e.g. user needs, aspirations, preferences, knowledge level, goals have to be taken into account for this purpose. Technically, this possibility is referred to as adaptiveness, and it requires user data. It is these data (user model that determine the adaptiveness conditions. Our aim is to build a user model for adaptive systems applied to nutritional requirements, modelling user characteristics that affect their diets and help to improve their health. To build the user model, we apply the user profile usability technique. In order to validate our proposal, we analyse and design a preliminary prototype of an adaptive system capable of making food recommendations to satisfy specific user needs. This study revealed that diet is a propitious field for the development of adaptive systems and that user modelling is a good choice for design of this type of systems.

  16. Gas chromatography/ion trap mass spectrometry applied for the analysis of triazine herbicides in environmental waters by an isotope dilution technique

    International Nuclear Information System (INIS)

    Cai Zongwei; Wang Dongli; Ma, W.T.

    2004-01-01

    A gas chromatography/ion trap mass spectrometry method was developed for the analysis of simazine, atrazine, cyanazine, as well as the degradation products of atrazine, such as deethylatrazine and deisopropylatrazine in environmental water samples. Isotope dilution technique was applied for the quantitative analysis of atrazine in water at low ng/l levels. One liter of water sample spiked with stable isotope internal standard atrazine-d 5 was extracted with a C 18 solid-phase extraction cartridge. The analysis was performed on an ion trap mass spectrometer operated in MS/MS method. The extraction recoveries were in the range of 83-94% for the triazine herbicides in water at the concentrations of 24, 200, and 1000 ng/l, while poor recoveries were obtained for the degradation products of atrazine. The relative standard deviation (R.S.D.) were within the range of 3.2-16.1%. The detection limits of the method were between 0.75 and 12 ng/l when 1 l of water was analyzed. The method was successfully applied to analyze environmental water samples collected from a reservoir and a river in Hong Kong for atrazine detected at concentrations between 3.4 and 26 ng/l

  17. Novas técnicas de reometria aplicadas a suspensões cerâmicas Novel rheometric techniques applied to ceramic suspensions

    Directory of Open Access Journals (Sweden)

    R. D. dos Anjos

    2005-06-01

    Full Text Available Suspensões cerâmicas com adequado comportamento reológico são imprescindíveis para a aplicação, adequação do processamento e otimização das propriedades finais dos produtos. No entanto, o uso de técnicas de reometria para análise de suspensões cerâmicas foi pouco explorado na literatura, quando comparado a outros sistemas, tais como polímeros fundidos. Desse modo, pretende-se demonstrar que o emprego de técnicas mais modernas de reometria permite uma nova compreensão desses materiais e das interações entre seus componentes. Neste trabalho foi estabelecida uma metodologia de análise para sistemas cerâmicos tendo como objeto de pesquisa uma suspensão de alumina e sol de sílica. Foi realizada uma série de medidas de viscosidade (eta, módulos de armazenamento (G' e de perda (G" e de força normal (Fn, cujos resultados servirão de base para estudos posteriores no mesmo sistema, visando aplicação em concretos refratários.Ceramic suspensions with suitable rheological properties are essential on application, process control and optimization of end products and properties. Nevertheless, the use of rheometric techniques to analyze such suspensions has been scarcely studied when compared to other systems, such as molten polymers. Therefore, in the present work, novel rheometric techniques will be presented which can allow a further understanding regarding these materials and the interaction among their components. A systematic study applying these techniques was established and the viscosity, storage modulus, loss modulus and normal force measurements were evaluated in a ceramic suspension containing alumina and silica sol. These results will be the fundaments for further studies, aiming their application on refractory castables.

  18. ‘The only way is Essex’: Gender, union and mobilisation among fire service control room staff

    OpenAIRE

    Hudson, Lynne; Moore, Sian; Tainsh, Kate; Taylor, Phil; Wright, Tessa

    2017-01-01

    This contribution to On the Front Line records a dialogue between two female Fire Brigades Union (FBU) representatives in the Essex Emergency Control Room who led industrial action over the imposition of a shift system that stretched their work–life balance to breaking point and constrained their ability to work full-time. Their testimony reveals how male members were mobilised in the interests of predominantly female control staff. Kate and Lynne’s discussion illuminates the interaction of g...

  19. Mobilising culture against domestic violence in migrant and ethnic communities: practitioner perspectives from Aotearoa/New Zealand.

    Science.gov (United States)

    Simon-Kumar, Rachel; Kurian, Priya A; Young-Silcock, Faith; Narasimhan, Nirmala

    2017-07-01

    Studies on domestic violence in ethnic minority communities highlight that social norms, family structures and cultural practices are among the key triggers of violence against women. Not surprisingly, most anti-violence interventions in these communities aim to redeem women from the oppressive features of these cultures. More recently, however, emergent scholarship advocates mobilising, rather than erasing, culture within existing anti-violence strategies. This paper explores the nature of culturally informed interventions used by front-line workers. It presents the findings of a small-scale qualitative study in Aotearoa/New Zealand, where around 13% of the population are currently deemed to be from minority ethnic communities. Interviews and one focus group were conducted with nine practitioners - including social workers, counsellors and the police - in Hamilton, Aotearoa in 2013-2014. Based on thematic analysis, the paper identifies two core strands: (a) the distinctive profile of ethnic violence and (b) the strategies that mobilise culture in anti-violence interventions. Specifically within the former strand, it was found that violence in the ethnic community was distinctive for the following reasons: the heightened sense of stigma surrounding disclosure and the consequent silence by women who suffer from it; the lack of trust in authority; and the fear of conventional safety plans necessitating longer time periods for rapport-building. Among the strategies that mobilise culture, the study found that practitioners used a family approach; engaged men in their interventions, at times reinforcing gendered roles; utilised micro-interventions; and deployed cultural tropes, especially around spirituality, as a strategy. The conclusion points to the gap between interventions that challenge and mobilise cultures. While anecdotally, the latter are perceived to be relevant and effective in anti-violence interventions, there is need for a fuller assessment and better

  20. The number of in-out catheterisations is reduced by mobilising the postoperative patient with bladder needs to the toilet in the recovery room

    DEFF Research Database (Denmark)

    Hansen, Anette Maria; Olsen, Karsten S

    2015-01-01

    BACKGROUND: Many patients are diagnosed with postoperative urine retention in the recovery room and treated with in-out catheterisation (IOC). OBJECTIVES: We hypothesised that the use of IOC could be reduced by mobilising patients to the toilet to pass urine instead of offering a bedpan or urinal...... ward mobilisation were 85 (37 to 139) min in Group I and 180 (118 to 245) min in Group C (P strategy decreased the number of IOCs, duration of stay in the recovery...

  1. L’appel du travail. Technologies et mobilisation subjective d’intérimaires « non-qualifiés » The call of work. Subjective mobilisation of “unqualified” temporary workers El llamado del trabajo. Tecnologías y movilización subjetiva de trabajadores temporales “no calificados”

    Directory of Open Access Journals (Sweden)

    Philippe Rosini

    2012-12-01

    Full Text Available Cet article traite de la mobilisation de travailleurs temporaires au travers des propositions de missions qu’ils peuvent recevoir, à tout moment, sur leurs téléphones portables. Il s’agit de montrer comment les intérimaires composent avec ces offres d’emploi en fonction de leurs positions sociales et du rapport qu’ils entretiennent à leur condition de « temporaire ». Il ressort que ces sollicitations soudaines et irrégulières contribuent à intensifier la disponibilité des candidats à l’embauche temporaire autant que la concurrence entre eux. Ce dispositif managérial s’appuie largement sur l’insécurité temporelle inhérente à ce régime d’emploi dont la plupart des intérimaires (« non qualifiés » souhaitent se détacher. À travers l’usage d’un objet technique, l’auteur examine certains mécanismes qui participent à la mobilisation numérique (obtenir le nombre d’intérimaires nécessaire mais également subjective des salariés.The article speaks to the mobilisation of temporary workers through the mission proposals that they might receive at any time on their mobile phones. Its purpose is to demonstrate how temporary workers cope with such job offers in light of their social position and how they relate to their “temporary” status. It discovers that sudden and irregular requests of this sort help to increase the number of applicants willing to accept temporary positions, while intensifying the competition between them. This type of management is largely predicated on the temporary insecurity that is inherent to such work, one that most “unqualified” temporary workers would like to avoid. The author uses a technical object to examine some of the mechanisms that help to mobilise employees both numerically (obtaining the necessary number of temporary workers and subjectively.El presente artículo aborda la movilización de los trabajadores temporales a partir de propuestas de trabajo que

  2. Knowledge mobilisation in healthcare: a critical review of health sector and generic management literature.

    Science.gov (United States)

    Ferlie, Ewan; Crilly, Tessa; Jashapara, Ashok; Peckham, Anna

    2012-04-01

    The health policy domain has displayed increasing interest in questions of knowledge management and knowledge mobilisation within healthcare organisations. We analyse here the findings of a critical review of generic management and health-related literatures, covering the period 2000-2008. Using 29 pre-selected journals, supplemented by a search of selected electronic databases, we map twelve substantive domains classified into four broad groups: taxonomic and philosophical (e.g. different types of knowledge); theoretical discourse (e.g. critical organisational studies); disciplinary fields (e.g. organisational learning and Information Systems/Information Technology); and organisational processes and structures (e.g. organisational form). We explore cross-overs and gaps between these traditionally separate literature streams. We found that health sector literature has absorbed some generic concepts, notably Communities of Practice, but has not yet deployed the performance-oriented perspective of the Resource Based View (RBV) of the Firm. The generic literature uses healthcare sites to develop critical analyses of power and control in knowledge management, rooted in neo-Marxist/labour process and Foucauldian approaches. The review generates three theoretically grounded statements to inform future enquiry, by: (a) importing the RBV stream; (b) developing the critical organisational studies perspective further; and (c) exploring the theoretical argument that networks and other alternative organisational forms facilitate knowledge sharing. Copyright © 2012 Elsevier Ltd. All rights reserved.

  3. Municipal mobilisation of materials for the landscape conservation; Kommunale Mobilisierung von Landschaftspflegematerial

    Energy Technology Data Exchange (ETDEWEB)

    Bruening, Arnd; Kottbusch, Bastian; Haensch, David; Hartz, Franziska [Bruening-Megawatt GmbH, Fischerhude (Germany)

    2013-10-01

    Since summer 2012, Bruening-Megawatt GmbH has been making more intensive efforts in coordinating community mobilisation of landscape management material. Such material is an important factor in maintaining full supply to the 6 biomass power (and thermal energy) plants, under contract to Bayernfonds BestEnergy 1 GmbH and Co. KG (BBE). These plants, located at Niesky, Leipzig, Bad Arolsen, Steinau an der Strasse, Langelsheim and Rieste, each have an output of 5 MW/h and consume approx. 200 tonnes of solid fuel every day. Already a proportion amounting to 1/10 of this requirement (approx. 25 tonnes, or 1 truck-trailer load) originates from community projects during the landscape maintenance months. For the period from October to February this yields a total of approximately 3,750 tonnes per power plant. Summed up over all 6 BBE plants, Bruning-Megawatt GmbH thus supplies approximately 22,500 tonnes of landscape management material originating from cooperation with municipalities and towns, to these biomass power (and thermal energy) plants. This amount is accordingly reduced during the summer months. These projects prove to be financially practical for the municipalities. They do not need to pay third parties for the disposal of branch cuttings and hedgerow trimmings, and Bruening-Megawatt GmbH pays them a fixed amount per tonne, depending on the quality of the clippings. (orig.)

  4. Deliberated opinion of the Environmental Authority on the national strategy for biomass mobilisation (SNMB)

    International Nuclear Information System (INIS)

    Barthod, Christian; Clement, Marc; Duval, Francois; Ledenvic, Philippe; Letourneux, Francois; Muller, Serge; Orizet, Francois-Regis; Perrin, Therese; Ullmann, Gabriel; Vindimian, Eric

    2017-01-01

    This document first presents the context of the French project of national strategy for biomass mobilisation (SNMB) as an application of the law related to energy transition for a green growth, and also as an item within the complex set of strategic documents such as the national strategy for low carbon, the national programme for forest and wood, the multi-year programming of energy, regional climate-air-energy schemes. It presents the SNMB project, its scope (with some recommendations made by the Environmental Authority), the usage challenges, the present situation of biomass with respect to the SNMB objectives for different biomass sources (forest, agriculture, breeding, by-products and wastes). It briefly discusses procedures related to the SNMB and to its environmental assessment. The second section addresses the analysis of the environmental assessment. It formulates some methodological recommendations, discusses the articulation with other programmes, and the initial analysis of the environment and of its perspectives of evolution, comments the justification of choices made regarding substitution solutions. It comments the analysis of likely effects of the SNMB implementation, and measures to avoid, mitigate or compensate these impacts. It briefly discusses the assessment of Natura 2000 effects, and choices made by the SNMB regarding indicators and modalities of environmental follow-up

  5. Is wartime mobilisation a suitable policy model for rapid national climate mitigation?

    International Nuclear Information System (INIS)

    Delina, Laurence L.; Diesendorf, Mark

    2013-01-01

    Climate science suggests that, to have a high probability of limiting global warming to an average temperature increase of 2 °C, global greenhouse gas emissions must peak by 2020 and be reduced to close to zero by 2040. However, the current trend is heading towards at least 4 °C by 2100 and little effective action is being taken. This paper commences the process of developing contingency plans for a scenario in which a sudden major global climate impact galvanises governments to implement emergency climate mitigation targets and programs. Climate activists assert that rapid mitigation is feasible, invoking the scale and scope of wartime mobilisation strategies. This paper draws upon historical accounts of social, technological and economic restructurings in several countries during World War 2 in order to investigate potential applications of wartime experience to radical, rigorous and rapid climate mitigation strategies. We focus on the energy sector, the biggest single contributor to global climate change, in developed and rapidly developing countries. We find that, while wartime experience suggests some potential strategies for rapid climate mitigation in the areas of finance and labour, it also has severe limitations, resulting from its lack of democratic processes. - Highlights: • The paper explores the strengths and weaknesses of using wartime experience as a model for rapid climate mitigation. • Wartime experience suggests some potential strategies for rapid climate mitigation in the areas of finance and labour. • Wartime experience also has severe limitations, resulting from its lack of democratic processes

  6. The policy work of piloting: Mobilising and managing conflict and ambiguity in the English NHS.

    Science.gov (United States)

    Bailey, Simon; Checkland, Kath; Hodgson, Damian; McBride, Anne; Elvey, Rebecca; Parkin, Stephen; Rothwell, Katy; Pierides, Dean

    2017-04-01

    In spite of their widespread use in policy making in the UK and elsewhere, there is a relatively sparse literature specifically devoted to policy pilots. Recent research on policy piloting has focused on the role of pilots in making policy work in accordance with national agendas. Taking this as a point of departure, the present paper develops the notion of pilots doing policy work. It does this by situating piloting within established theories of policy formulation and implementation, and illustrating using an empirical case. Our case is drawn from a qualitative policy ethnography of a local government pilot programme aiming to extend access to healthcare services. Our case explores the collective entrepreneurship of regional policy makers together with local pilot volunteers. We argue that pilots work to mobilise and manage the ambiguity and conflict associated with particular policy goals, and in their structure and design, shape action towards particular outcomes. We conclude with a discussion of the generative but managed role which piloting affords to local implementers. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  7. Smouldering peat fires in polluted landscapes and their impact on heavy metal mobilisation

    Science.gov (United States)

    Clay, Gareth; Rothwell, James; Shuttleworth, Emma

    2016-04-01

    Whilst wildfires are commonly viewed as a threat confined to Southern Europe, Australia, and North America, recognition of wildfire hazard in the UK has been growing in recent years. UK wildfires often occur on heathland vegetation underlain by peat. These areas can contain industrially-derived legacy pollutants, such as mercury, lead, and arsenic. Ignition of the peat can lead to long-term smouldering fires that are difficult to extinguish, leading to large-scale damage. While work on assessing post-fire damage of peatlands has focussed on carbon and nutrient dynamics, there has been little attention on the release of heavy metals following wildfires. This paper presents initial data from a preliminary study to assess heavy metal release from smouldering peat fires. A homogenised sample of peat from the Peak District National Park, UK was ignited, monitored using thermocouples and an IR camera, and left to smoulder until self-extinguished (~9 hours). Total mass loss was 61%. Samples of pre- and post-burn peat were analysed for their heavy metal concentrations using XRF, ICP-MS, and CVAFS. Sample analysis is ongoing, but initial data shows that there is a substantial (3x) relative enrichment in heavy metal concentrations in post-fire ash. This has important implications for subsequent mobilisation in the aquatic and terrestrial environments, as well as consequences for human health risk through atmospheric redistribution.

  8. The hydrodynamic drag and the mobilisation of sediment into the water column of towed fishing gear components

    Science.gov (United States)

    O'Neill, F. G.; Summerbell, Keith David

    2016-12-01

    The hydrodynamic drag of towed fishing gears leads to direct impacts on the benthic environment, and can play a major role in the overall economic efficiency of the fishing operation and emissions of nitrogen oxides, sulphur oxides and greenhouse gases such as CO2. Here we investigate some of the underpinning processes which govern these issues and make direct hydrodynamic drag measurements and calculate the hydrodynamic drag coefficients for a range of well-defined gear components that, when fished, are in contact with the seabed. We measure the concentration and particle size distribution of the sediment mobilised into the water column in the wake of these gear elements, at a range of towing speeds, and demonstrate that as the hydrodynamic drag increases the amount of sediment mobilised also increases. We also vary the weight of the elements and show that this does not influence the amount of sediment put into the water column. These results provide a better understanding of the physical and mechanical processes that take place when a towed fishing gear interacts with the seabed. They will permit the development of more fuel efficient gears and gears of reduced benthic impact and will improve the empirical modelling of the sediment mobilised into the turbulent wake behind towed fishing gears which will lead to better assessments of the environmental and ecological impact of fishing gears.

  9. Mobilisation of lipophilic pollutants from blubber in northern elephant seal pups (Mirounga angustirostris) during the post-weaning fast

    Energy Technology Data Exchange (ETDEWEB)

    Louis, Caroline [Institut des Sciences de la Vie, UCLouvain, Croix du Sud 2/L7.05.08, 1348 Louvain-la-Neuve (Belgium); Dirtu, Alin C. [Department of Pharmaceutical Sciences, Toxicological Center, Campus Drie Eiken, Universiteit Antwerpen, Universiteitsplein 1, 2610 Wilrijk (Belgium); Department of Chemistry, “Al. I. Cuza” University of Iasi, 700506 Iasi (Romania); Stas, Marie [Institut des Sciences de la Vie, UCLouvain, Croix du Sud 2/L7.05.08, 1348 Louvain-la-Neuve (Belgium); Guiot, Yves [Department of Pathology, Faculty of Medicine, UCLouvain, Brussels (Belgium); Malarvannan, Govindan [Department of Pharmaceutical Sciences, Toxicological Center, Campus Drie Eiken, Universiteit Antwerpen, Universiteitsplein 1, 2610 Wilrijk (Belgium); Das, Krishna [Laboratoire d’Océanologie, MARE Center B6c, Université de Liège, 4000 Liège (Belgium); Costa, Daniel P. [Ecology and Evolutionary Biology Department, University of California Santa Cruz, 100 Shaffer Rd, Santa Cruz, CA 95060 (United States); Crocker, Daniel E. [Department of Biology, Sonoma State University, 1801 East Cotati Ave, Rohnert Park, CA 94928 (United States); Covaci, Adrian [Department of Pharmaceutical Sciences, Toxicological Center, Campus Drie Eiken, Universiteit Antwerpen, Universiteitsplein 1, 2610 Wilrijk (Belgium); Debier, Cathy, E-mail: cathy.debier@uclouvain.be [Institut des Sciences de la Vie, UCLouvain, Croix du Sud 2/L7.05.08, 1348 Louvain-la-Neuve (Belgium)

    2014-07-15

    Northern elephant seals (NES) (Mirounga angustirostris) from the Año Nuevo State Reserve (CA, USA) were longitudinally sampled during the post-weaning fast in order to study the mobilisation and redistribution of various classes of persistent organic pollutants (POPs), such as polybrominated diphenyl ethers (PBDEs), polychlorinated biphenyls (PCBs), dichlorodiphenyldichloroethylene (p,p′-DDE) and hexachlorobenzene (HCB) between blubber and blood. Inner and outer blubber layers were analysed separately. Organohalogenated compounds were detected in all blubber samples in the decreasing order of their concentrations: p,p′-DDE>PCBs⪢HCB>PBDEs. The concentrations of all studied compounds were homogeneously distributed in the blubber layer at early fast, since the concentrations of POPs were statistically not different in the inner and outer layers. With the progression of the fast, the concentrations of PBDEs, PCBs and p,p′-DDE increased more sharply in inner blubber than in outer blubber. As a result, their levels became significantly higher in inner blubber as compared to outer blubber at late fast. The rise of pollutant concentrations in blubber might result from a less efficient mobilisation than triglycerides and/or a reuptake by adipocytes of some of the pollutants released into the circulation. The mobilisation of pollutants from blubber was higher at late fast. An increase of pollutant concentrations was observed in serum between early and late fast. Lower halogenated congeners (i.e. tetra-CBs) were present in higher proportions in serum, whereas the higher halogenated congeners (i.e. hepta-CBs) were mainly found in the inner and outer blubber layers. The transfer ratios of both PBDEs and PCBs from inner blubber to serum decreased with the number of chlorine and bromine atoms. In addition, the distribution of both types of compounds between serum and blubber was strongly influenced by their lipophilic character (log K{sub ow} values), with more

  10. Processes and challenges of community mobilisation for latrine promotion under Nirmal Bharat Abhiyan in rural Odisha, India.

    Science.gov (United States)

    Routray, Parimita; Torondel, Belen; Jenkins, Marion W; Clasen, Thomas; Schmidt, Wolf-Peter

    2017-05-16

    Despite efforts to eradicate it, open defecation remains widely practiced in India, especially in rural areas. Between 2013 and 2014, 50 villages in one district of Odisha, India, received a sanitation programme under the Nirmal Bharat Abhiyan (NBA - "Clean India Campaign"), the successor of India's Total Sanitation Campaign. This paper documents the strategies and processes of NBA community mobilisation for latrine promotion in these villages and assesses the strengths and limitations of the mobilisation activities. NBA's community mobilisation activities were observed and assessed against the programme's theory of change in 10 randomly selected programme villages from start to finish. Additional data was collected through review of documents, individual interviews (n = 80) and focus group discussions (n = 26) with staff of the implementing NGOs and community members. Our study revealed the lack of a consistent implementation strategy, lack of capacities and facilitation skills of NGO staff to implement sanitation programmes, political interference, challenges in accessing government financial incentives for latrine construction, and lack of clarity on the roles and responsibilities among government and NGO staff, leading to failure in translating government policies into sustainable actions. Social divisions and village dynamics related to gender and caste further constrained the effectiveness of mobilisation activities. Meetings were often dominated by male members of upper caste households, and excluded low caste community members and views of women. Community discussions revolved largely around the government's cash incentive for latrines. Activities aimed at creating demand for sanitation and use of latrines often resonated poorly with community members. An assessment by the implementers, 1 year after community mobilisation found 19% of households had a completed latrine across the 50 villages, a marginal increase of 7 percentage points over baseline. In

  11. Processes and challenges of community mobilisation for latrine promotion under Nirmal Bharat Abhiyan in rural Odisha, India

    Directory of Open Access Journals (Sweden)

    Parimita Routray

    2017-05-01

    Full Text Available Abstract Background Despite efforts to eradicate it, open defecation remains widely practiced in India, especially in rural areas. Between 2013 and 2014, 50 villages in one district of Odisha, India, received a sanitation programme under the Nirmal Bharat Abhiyan (NBA – “Clean India Campaign”, the successor of India’s Total Sanitation Campaign. This paper documents the strategies and processes of NBA community mobilisation for latrine promotion in these villages and assesses the strengths and limitations of the mobilisation activities. Methods NBA’s community mobilisation activities were observed and assessed against the programme’s theory of change in 10 randomly selected programme villages from start to finish. Additional data was collected through review of documents, individual interviews (n = 80 and focus group discussions (n = 26 with staff of the implementing NGOs and community members. Results Our study revealed the lack of a consistent implementation strategy, lack of capacities and facilitation skills of NGO staff to implement sanitation programmes, political interference, challenges in accessing government financial incentives for latrine construction, and lack of clarity on the roles and responsibilities among government and NGO staff, leading to failure in translating government policies into sustainable actions. Social divisions and village dynamics related to gender and caste further constrained the effectiveness of mobilisation activities. Meetings were often dominated by male members of upper caste households, and excluded low caste community members and views of women. Community discussions revolved largely around the government’s cash incentive for latrines. Activities aimed at creating demand for sanitation and use of latrines often resonated poorly with community members. An assessment by the implementers, 1 year after community mobilisation found 19% of households had a completed latrine across the 50

  12. Does the addition of deep breathing exercises to physiotherapy-directed early mobilisation alter patient outcomes following high-risk open upper abdominal surgery? Cluster randomised controlled trial.

    Science.gov (United States)

    Silva, Y R; Li, S K; Rickard, M J F X

    2013-09-01

    To investigate whether the inclusion of deep breathing exercises in physiotherapy-directed early mobilisation confers any additional benefit in reducing postoperative pulmonary complications (PPCs) when patients are treated once daily after elective open upper abdominal surgery. This study also compared postoperative outcomes following early and delayed mobilisation. Cluster randomised controlled trial. Single-centre study in a teaching hospital. Eighty-six high-risk patients undergoing elective open upper abdominal surgery. Three groups: early mobilisation (Group A), early mobilisation plus breathing exercises (Group B), and delayed mobilisation (mobilised from third postoperative day) plus breathing exercises (Group C). PPCs and postoperative outcomes [number of days until discharge from physiotherapy, physiotherapy input and length of stay (LOS)]. There was no significant difference in PPCs between Groups A and B. The LOS for Group A {mean 10.7 [standard deviation (SD) 5.0] days} was significantly shorter than the LOS for Groups B [mean 16.7 (SD 9.7) days] and C [mean 15.2 (SD 9.8) days; P=0.036]. The greatest difference was between Groups A and B (mean difference -5.93, 95% confidence interval -10.22 to -1.65; P=0.008). Group C had fewer smokers (26%) and patients with chronic obstructive pulmonary disease (0%) compared with Group B (53% and 14%, respectively). This may have led to fewer PPCs in Group C, but the difference was not significant. Despite Group C having fewer PPCs and less physiotherapy input, the number of days until discharge from physiotherapy and LOS were similar to Group B. The addition of deep breathing exercises to physiotherapy-directed early mobilisation did not further reduce PPCs compared with mobility alone. PPCs can be reduced with once-daily physiotherapy if the patients are mobilised to a moderate level of exertion. Delayed mobilisation tended to increase physiotherapy input and the number of days until discharge from physiotherapy

  13. Applying the change vector analysis technique to assess the desertification risk in the south-west of Romania in the period 1984-2011.

    Science.gov (United States)

    Vorovencii, Iosif

    2017-09-26

    The desertification risk affects around 40% of the agricultural land in various regions of Romania. The purpose of this study is to analyse the risk of desertification in the south-west of Romania in the period 1984-2011 using the change vector analysis (CVA) technique and Landsat thematic mapper (TM) satellite images. CVA was applied to combinations of normalised difference vegetation index (NDVI)-albedo, NDVI-bare soil index (BI) and tasselled cap greenness (TCG)-tasselled cap brightness (TCB). The combination NDVI-albedo proved to be the best in assessing the desertification risk, with an overall accuracy of 87.67%, identifying a desertification risk on 25.16% of the studied period. The classification of the maps was performed for the following classes: desertification risk, re-growing and persistence. Four degrees of desertification risk and re-growing were used: low, medium, high and extreme. Using the combination NDVI-albedo, 0.53% of the analysed surface was assessed as having an extreme degree of desertification risk, 3.93% a high degree, 8.72% a medium degree and 11.98% a low degree. The driving forces behind the risk of desertification are both anthropogenic and climatic causes. The anthropogenic causes include the destruction of the irrigation system, deforestation, the destruction of the forest shelterbelts, the fragmentation of agricultural land and its inefficient management. Climatic causes refer to increase of temperatures, frequent and prolonged droughts and decline of the amount of precipitation.

  14. Feasibility of applying gamma irradiation as disinfestation technique on date fruits in respect to nutritional value that is affected by disinfesting gamma ray doses

    International Nuclear Information System (INIS)

    Ahmed, El-Sayed S.

    1976-01-01

    Infested and non-infested dry date fruits (Phonex dactylifera), Abrimi variety (9.2% moisture), with Ephestia cautella Walker were irradiated for 0, 15, 20 and 40 Krad gamma ray doses emitted from Co-60 source with 1.36 x 10-rad/h. as a dose rate. Irradiated fruits were stored at room temperature, at 20-25 0 C and 85-95% R.H., in packages to avoid reinfestation. A dose of 20 Krad is 100 percent effective in preventing the emergency of eggs, larva, and pupae in fruits as reflected by zero per cent emergency count for live adults. Also, this dose was found to be lethal for adult stage of the insect. On the other hand, 2 Krad dose does not produce significant changes in the nutritional qualities of fruits, as measured by chemical analytical means for carbohydrates, protein and amino acids, directly after irradiation as well as at 2, 4 and 6 months storage. The triangular tests show that irradiation treatments even with 4 Krad exerted no determinal effect upon the sensory qualities of stored irradiated date fruits. These results point out the feasibility of applying gamma irradiation, 20 Krad, as disinfestation technique against Ephestia cautella Walker in dry date fruits without exerting any effect on the nutritional value

  15. Dependence of early therapy results and complications on radiation dose values and their fractionation in pre-operative ''afterloading'' technique brachyradiotherapy applied to cervix uteri carcinoma patients

    International Nuclear Information System (INIS)

    Kaminska, G.; Kawczynska, M.

    1984-01-01

    The ''afterloading'' technique with use of Curietron (41 cases) or Selectron (43 cases) apparatus was applied in 83 cervix uteri carcinoma patients in phase 1b (79 cases) and 2a (4 cases). The Wertheim-Magis operation was performed after several weeks. Post-operative histologic investigation showed complete destruction of the tumour in 72% cases; persistent cancer cells in cervix uteri were stated in 11 patients (13%), while lymphatic node metastasis was seen in 14 patients (17%). Supplementary teleradiotherapy was performed in those cases. 39 patients (95%) of the 41 observed during 3 years survived without any cancer symptoms. No explicit relationship between dose administered to vaginal disc and cancer persistence frequency in the cervix uteri was stated. However, such relationship was stated for the dose in point A. In the group of 19 patients who received point A dose of the least 6000 rads, with average TDF value of 135, presence of cancer cells in cervix uteri was not stated in any of the cases. In 7 patients (17%) observed for over 3 years light and medium heavy postradiation complications were stated; in that 5 rectum side complications were stated in patients additionally irradiated from external fields, where the dose absorbed by rectum wall exceeded 8000 rads, with TDF - 150. No complications were observed when the dose was less than 5000 rads and TDF below 100. 16 refs., 1 fig. (author)

  16. Geology for Global Development: Mobilising and equipping young geologists to engage in disaster risk reduction

    Science.gov (United States)

    Gill, Joel

    2016-04-01

    Geology for Global Development (GfGD) is a not-for-profit organisation working to mobilise and equip geologists to engage in all aspects of sustainable development, including disaster risk reduction (DRR). Geologists have a crucial role to play in DRR, and the recently agreed Sendai Framework for DRR 2015-2030. This framework aims to significantly reduce loss of lives and livelihoods due to disasters. The geology community have an understanding of the Earth, its physical structure, and the processes by which it is constantly being shaped which are of particular relevance to Priorities for Action 1 and 4 noted within the Sendai Framework. Effective engagement by geologists, however, requires many skills beyond the standard geology curriculum. Cultural understanding, cross-disciplinary communication, diplomacy, community mobilization and participation, knowledge exchange, and an understanding of social science research tools are commonly necessary for effective research and engagement in the science-policy-practice interface. Topical and disciplinary knowledge, such as understanding social vulnerability, international policy frameworks and development theory are also rarely included in the education and professional training of a young geologist. Through the work of GfGD, we are training young geologists with these skills and the supporting knowledge required to make an effective contribution to reducing disaster risk, support civil society, empower communities and help to strengthen resilience. University chapters have been established in 14 major UK and Irish universities, coordinating extra-curricular seminars, workshops and discussion activities. Our work is currently focused on supporting young geologists, but we are increasingly a respected voice at international geoscience forums that gather a wide range of students and professionals. Wider (national and international) activities include conferences, placements and facilitating youth engagement in education

  17. Rapid arsenic(V)-reduction by fire in schwertmannite-rich soil enhances arsenic mobilisation

    Science.gov (United States)

    Johnston, Scott G.; Bennett, William W.; Burton, Edward D.; Hockmann, Kerstin; Dawson, Nigel; Karimian, Niloofar

    2018-04-01

    Arsenic in acid sulfate soil (ASS) landscapes commonly associates with schwertmannite, a poorly crystalline Fe(III) mineral. Fires in ASS landscapes can thermally transform Fe(III) minerals to more crystalline phases, such as maghemite (γFe2O3). Although thermal genesis of maghemite requires electron transfer via organic matter pyrolysis, the possibility of fire causing concurrent transfer of electrons to schwertmannite-bound As(V) remains unexplored. Here, we subject an organic-rich soil with variable carbon content (∼9-44% organic C) mixed (4:1) with As(V)-bearing schwertmannite (total As of 4.7-5.4 μmol g-1), to various temperatures (200-800 °C) and heating durations (5-120 min). We explore the consequences for As and Fe via X-ray absorption spectroscopy, X-ray diffraction, 57Fe Mössbauer spectroscopy and selective extracts. Heating transforms schwertmannite to mainly maghemite and hematite at temperatures above 300-400 °C, with some transitory formation of magnetite, and electrons are readily transferred to both Fe(III) and As(V). As(V) reduction to As(III) is influenced by a combination of temperature, heating duration and carbon content and is significantly (P moderate fires in ASS landscapes, even of short duration, may generate considerable labile As(III) species and cause a pulse of As(III)aq mobilisation following initial re-wetting. Further research is warranted to examine if analogous As(III) formation occurs during combustion of organic-rich soil containing common As-bearing Fe(III) minerals such as ferrihydrite and goethite.

  18. Scaling up community mobilisation through women's groups for maternal and neonatal health: experiences from rural Bangladesh

    Directory of Open Access Journals (Sweden)

    Nahar Tasmin

    2012-01-01

    Full Text Available Abstract Background Program coverage is likely to be an important determinant of the effectiveness of community interventions to reduce neonatal mortality. Rigorous examination and documentation of methods to scale-up interventions and measure coverage are scarce, however. To address this knowledge gap, this paper describes the process and measurement of scaling-up coverage of a community mobilisation intervention for maternal, child and neonatal health in rural Bangladesh and critiques this real-life experience in relation to available literature on scaling-up. Methods Scale-up activities took place in nine unions in rural Bangladesh. Recruitment and training of those who deliver the intervention, communication and engagement with the community and other stakeholders and active dissemination of intervention activities are described. Process evaluation and population survey data are presented and used to measure coverage and the success of scale-up. Results The intervention was scaled-up from 162 women's groups to 810, representing a five-fold increase in population coverage. The proportion of women of reproductive age and pregnant women who were engaged in the intervention increased from 9% and 3%, respectively, to 23% and 29%. Conclusions Examination and documentation of how scaling-up was successfully initiated, led, managed and monitored in rural Bangladesh provide a deeper knowledge base and valuable lessons. Strong operational capabilities and institutional knowledge of the implementing organisation were critical to the success of scale-up. It was possible to increase community engagement with the intervention without financial incentives and without an increase in managerial staff. Monitoring and feedback systems that allow for periodic programme corrections and continued innovation are central to successful scale-up and require programmatic and operational flexibility.

  19. Decision-Making Tool for Cost-Efficient and Environmentally Friendly Wood Mobilisation

    Directory of Open Access Journals (Sweden)

    Matevž Triplat

    2015-06-01

    Full Text Available Background and Purpose: With development of forest management technologies, the efficiency of wood production was significantly improved, and thus the impact on forests has changed as well. The article presents a practical decision-making tool for selection of most suitable harvesting system, considering given terrain as well as expected soil conditions on harvesting sites. The decision-making tool should support cost-efficient and environmentally friendly mobilisation of wood. Materials and Methods: The presented decision-making tool is based on ground bearing capacities (relevant environmental parameter and nominal ground pressure (harvesting system characteristics. Soil and terrain (slope characteristics were taken into account for selection of the most suitable harvesting system. Three-step methodological approach was suggested, where soil and terrain conditions were defined in first step, while harvesting system were described using wood process charts (“functiogramms” in second step. In final step ecological and technological requirements were matched. Results: To exemplify the three-step methodology, a decision-making tool was prepared for the three selected harvesting systems. The proposed harvesting systems differ in technological, ecological and economic aspects, but each is limited by at least one of the aspect. Conclusions: The decision-making tool in combination with the presented wood process charts (“functiogramms” can simplify and facilitate forest production planning, although it can also be used in case of unforeseen event e.g. changing of soil moisture, machinery failure and insufficient current capacities. Considering the envisaged quantities and types of forest wooden assortments, it is possible to use the decision-making tool for a basic selection of most appropriate harvesting systems. The main idea behind the suggested three step methodological approach is that forest workers can prepare individual decision

  20. Mobilisation, politics, investment and constant adaptation: lessons from the Australian health-promotion response to HIV.

    Science.gov (United States)

    Brown, Graham; O'Donnell, Daryl; Crooks, Levinia; Lake, Rob

    2014-04-01

    The Australian response to HIV oversaw one of the most rapid and sustained changes in community behaviour in Australia's health-promotion history. The combined action of communities of gay men, sex workers, people who inject drugs, people living with HIV and clinicians working in partnership with government, public health and research has been recognised for many years as highly successful in minimising the HIV epidemic. This article will show how the Australian HIV partnership response moved from a crisis response to a constant and continuously adapting response, with challenges in sustaining the partnership. Drawing on key themes, lessons for broader health promotion are identified. The Australian HIV response has shown that a partnership that is engaged, politically active, adaptive and resourced to work across multiple social, structural, behavioural and health-service levels can reduce the transmission and impact of HIV. The experience of the response to HIV, including its successes and failures, has lessons applicable across health promotion. This includes the need to harness community mobilisation and action; sustain participation, investment and leadership across the partnership; commit to social, political and structural approaches; and build and use evidence from multiple sources to continuously adapt and evolve. So what? The Australian HIV response was one of the first health issues to have the Ottawa Charter embedded from the beginning, and has many lessons to offer broader health promotion and common challenges. As a profession and a movement, health promotion needs to engage with the interactions and synergies across the promotion of health, learn from our evidence, and resist the siloing of our responses.