Energy, mining, and the commercial success of the Newcomen "steam" engine

Science.gov (United States)

Murphy, John Paul

This dissertation is about energy; specifically how prime movers changed at the beginning of the Industrial Revolution. These power needs are explored via the history of the Newcomen atmospheric engine, as it was used in the 18th century to drive pumps in flooded mines. This approach examines society as an energy-converting phenomenon, and uses the concept of an energy rent. The dissertation seeks to reach past the 19th century's "high-pressure historiography" of the first engines powered by fire; instead, it traces the actual low-pressure atmospheric technology of the first commercially successful engines, and the surprising, rather than inevitable, transformation they engendered. The costs of fuel are shown to be an essential factor in the success or failure of the first Newcomen engines. Thomas Newcomen's failed first attempts in Cornwall (1710) are contrasted with success in collieries, located in the relatively distant region of the Midlands, only two years later. To test the suggestion that coal is needed for a Newcomen engine to be profitable, two detailed case histories compare 18th century engines, both fired using wood fuel, at iron ore mines. The first was a failed engine at Dannemora, Sweden (1728); the second a successful machine built by the Brown brothers at Cranston, Rhode Island (1783). The Brown engine's case history was based on extensive original archive research, and also provides a detailed history of the Hope Furnace, which used the ore from Cranston. Success for the Browns in Rhode Island is found to have been rooted in their careful planning for fuel needs. The two mines were also found to have significantly different construction of gender roles, suggesting the Rhode Island context had established more thoroughly capitalist relations. The work shows that the demand for more extensive power, which led to these engines, was propelled by the ability of the evolving commercial market place to convert energy profitably (16th and 17th centuries

Methodologies of Knowledge Discovery from Data and Data Mining Methods in Mechanical Engineering

Directory of Open Access Journals (Sweden)

Rogalewicz Michał

2016-12-01

Full Text Available The paper contains a review of methodologies of a process of knowledge discovery from data and methods of data exploration (Data Mining, which are the most frequently used in mechanical engineering. The methodologies contain various scenarios of data exploring, while DM methods are used in their scope. The paper shows premises for use of DM methods in industry, as well as their advantages and disadvantages. Development of methodologies of knowledge discovery from data is also presented, along with a classification of the most widespread Data Mining methods, divided by type of realized tasks. The paper is summarized by presentation of selected Data Mining applications in mechanical engineering.

RE-ENGINEERING PRIMARY HEALTHCARE NURSING AS A FIRST CAREER CHOICE.

Science.gov (United States)

Wheeler, Emily; Govan, Linda

2016-08-01

In line with international models and critical to the primary healthcare nursing workforce, the Australian Primary Health Care Nursing Association (APNA) has been funded by the Commonwealth Department of Health to develop an Education and Career Framework and Toolkit for primary healthcare nurses. The aim of the project is to improve the recruitment and retention of nurses and to re-engineer primary healthcare as a first choice career option.

Innovations of Engineering Company and Competitiveness in the Mining Equipment Market

Science.gov (United States)

Pogrebnoi, Vladislav; Samorodova, Lyudmila; Shut'ko, Larisa; Yakunina, Yulia; Lyubimov, Oleg

2017-11-01

The article deals with issues related to the development of innovative projects by engineering companies and effective marketing policy as a factor of increasing their competitiveness in the mining equipment market. The paper presents the results of the development of innovative technology in the segment of extensible belt conveyors. The necessity of marketing the innovative project is proved by the example of the development of technology for the production of the motor-drum of a belt conveyor with an adjustable drive on continuous current magnets by the engineering company "Transport-Electroprivod" (LLC). The authors consider the effective marketing strategy of an engineering company as an attractor of increasing demand for innovation and competitiveness in the mining equipment market. The methods of marketing promotion and promotion of innovations are considered within the framework of the ecosystem concept of J. Moore.

Innovations of Engineering Company and Competitiveness in the Mining Equipment Market

Directory of Open Access Journals (Sweden)

Pogrebnoi Vladislav

2017-01-01

Full Text Available The article deals with issues related to the development of innovative projects by engineering companies and effective marketing policy as a factor of increasing their competitiveness in the mining equipment market. The paper presents the results of the development of innovative technology in the segment of extensible belt conveyors. The necessity of marketing the innovative project is proved by the example of the development of technology for the production of the motor-drum of a belt conveyor with an adjustable drive on continuous current magnets by the engineering company “Transport-Electroprivod” (LLC. The authors consider the effective marketing strategy of an engineering company as an attractor of increasing demand for innovation and competitiveness in the mining equipment market. The methods of marketing promotion and promotion of innovations are considered within the framework of the ecosystem concept of J. Moore.

Research on the optimization strategy of web search engine based on data mining

Science.gov (United States)

Chen, Ronghua

2018-04-01

With the wide application of search engines, web site information has become an important way for people to obtain information. People have found that they are growing in an increasingly explosive manner. Web site information is verydifficult to find the information they need, and now the search engine can not meet the need, so there is an urgent need for the network to provide website personalized information service, data mining technology for this new challenge is to find a breakthrough. In order to improve people's accuracy of finding information from websites, a website search engine optimization strategy based on data mining is proposed, and verified by website search engine optimization experiment. The results show that the proposed strategy improves the accuracy of the people to find information, and reduces the time for people to find information. It has an important practical value.

Aerosols emitted in underground mine air by diesel engine fueled with biodiesel.

Science.gov (United States)

Bugarski, Aleksandar D; Cauda, Emanuele G; Janisko, Samuel J; Hummer, Jon A; Patts, Larry D

2010-02-01

Using biodiesel in place of petroleum diesel is considered by several underground metal and nonmetal mine operators to be a viable strategy for reducing the exposure of miners to diesel particulate matter. This study was conducted in an underground experimental mine to evaluate the effects of soy methyl ester biodiesel on the concentrations and size distributions of diesel aerosols and nitric oxides in mine air. The objective was to compare the effects of neat and blended biodiesel fuels with those of ultralow sulfur petroleum diesel. The evaluation was performed using a mechanically controlled, naturally aspirated diesel engine equipped with a muffler and a diesel oxidation catalyst. The effects of biodiesel fuels on size distributions and number and total aerosol mass concentrations were found to be strongly dependent on engine operating conditions. When fueled with biodiesel fuels, the engine contributed less to elemental carbon concentrations for all engine operating modes and exhaust configurations. The substantial increases in number concentrations and fraction of organic carbon (OC) in total carbon over the baseline were observed when the engine was fueled with biodiesel fuels and operated at light-load operating conditions. Size distributions for all test conditions were found to be single modal and strongly affected by engine operating conditions, fuel type, and exhaust configuration. The peak and total number concentrations as well as median diameter decreased with an increase in the fraction of biodiesel in the fuels, particularly for high-load operating conditions. The effects of the diesel oxidation catalyst, commonly deployed to counteract the potential increase in OC emissions due to use of biodiesel, were found to vary depending upon fuel formulation and engine operating conditions. The catalyst was relatively effective in reducing aerosol number and mass concentrations, particularly at light-load conditions, but also showed the potential for an

Australian coal mine methane emissions mitigation potential using a Stirling engine-based CHP system

International Nuclear Information System (INIS)

Meybodi, Mehdi Aghaei; Behnia, Masud

2013-01-01

Methane, a major contributor to global warming, is a greenhouse gas emitted from coal mines. Abundance of coal mines and consequently a considerable amount of methane emission requires drastic measures to mitigate harmful effects of coal mining on the environment. One of the commonly adopted methods is to use emitted methane to fuel power generation systems; however, instability of fuel sources hinders the development of systems using conventional prime movers. To address this, application of Stirling engines may be considered. Here, we develop a techno-economic methodology for conducting an optimisation-based feasibility study on the application of Stirling engines as the prime movers of coal mine CHP systems from an economic and an environmental point of view. To examine the impact of environmental policies on the economics of the system, the two commonly implemented ones (i.e. a carbon tax and emissions trading scheme) are considered. The methodology was applied to a local coal mine. The results indicate that incorporating the modelled system not only leads to a substantial reduction in greenhouse gas emissions, but also to improved economics. Further, due to the heavy economic burden, the carbon tax scheme creates great incentive for coal mine industry to address the methane emissions. -- Highlights: •We study the application of Stirling engines in coal mine CHP systems. •We develop a thermo-economic approach based on the net present worth analysis. •We examine the impact of a carbon tax and ETS on the economics of the system. •The modeled system leads to a substantial reduction in greenhouse gas emissions. •Carbon tax provides a greater incentive to address the methane emissions

Mine engineering and ventilation problems unique to the control of radon daughters

International Nuclear Information System (INIS)

Rock, R.L.

1975-01-01

Quality and quantity of ventilation are the two interrelated but key factors in any radon-daughter control programme. The better the intake air quality (little or no contamination from radon and its daughters), the less are the total air requirements for ventilation of active mining areas. Engineering principles for quantity distribution of air through underground working areas are straightforward and the formulae and theories governing forced ventilation are not within the scope of this paper. Rather, this paper discusses the principal methods of utilizing mine planning to facilitate radon-daughter control and also treats the more subtle features of mine ventilation which are especially critical in the ventilation of mines where radon gas constitutes an environmental contamination problem. (author)

The motivational needs of primary health care nurses to acquire power as leaders in a mine clinic setting

Directory of Open Access Journals (Sweden)

Karien Jooste

2017-10-01

Full Text Available Motivation is a process that influences and directs behaviour in order to satisfy a need. It links with goal 3 of the sustainable development goals that focus on ensuring healthy lives and promoting well-being at all ages. Motivation of nurses is important in the primary health care environment of, for instance, mine settings; since low levels of motivation among Primary Health Care (PHC nurses could have a negative effect on the achievement of high standards in health service delivery. The study was conducted within the theoretical framework of McClelland's Acquired Motivation Theory which consists of three basic needs, – the need for achievement, the need for power, and the need for affiliation. One of the research questions posed was “What are the motivational needs of PHC nurses to acquire power in the workplace at mine clinic settings?” A quantitative, explorative, descriptive design was followed. The accessible population in this study was PHC nurses (N = 30 working at 13 mine clinics, that also served as the total sample. A 7 point Likert scale was used in a self-administered structured questionnaire that was developed from a literature review. Ethical considerations were adhered to and respondents gave written informed consent. Data was analysed by using descriptive and inferential statistics. TheManne Whitney test compared the mean ranks and a p-value of p < 0.05 was indicative of a significant difference between male and female groups. Validity and reliability principles were applied during the entire research process. The results indicated that PHC nurses needed acknowledgement, organisational responsibility, strategic planning and promotion, as well as support. Significant differences between gender were not found in relation to the need to acquire power.

Cross-cultural analysis of the verbal conflict behavior of the graduate mining engineers

Directory of Open Access Journals (Sweden)

Pevneva Inna

2017-01-01

Full Text Available The article is devoted to the crucial issue of the interpersonal communication skills of engineering graduates and studies the verbal behavior of the graduates majoring in mining engineering in conflict professional communication considered in a cross-cultural aspect. The research is based on the needs that future mining engineers have for conducting successful communication, work in teams and run an effective discourse both verbally and in writing. Verbal communication involves a strategic process by which a speaker defines the language resources for its implementation. By choosing a strategy which should contribute to the goals and objectives of the interaction a speaker makes the process of communication either successful or leading to a communicative failure. The scientific importance of this work is in multidiscipline approach and cross-cultural study of ethnic and cultural influences, gender and other characteristics of the verbal behavior of Russian and American engineering graduates.

Innovative Competencies of Mining engineers in Transition to the Sustainable Development

Science.gov (United States)

Krechetov, Andrey; Khoreshok, Alexey; Blumenstein, Valery

2017-11-01

The transition to the sustainable development posed new challenges to the system of mining higher education. They are determined by the acceleration of scientific and technological progress and widespread introduction of innovations, convergence of technologies from various industries. On the one hand, globalization and rapid technology development are constantly increasing quality requirements for the labor resources of the mineral and raw materials complex and constant improvement of their skills. On the other hand, the transition to the sustainable development provides the necessity for rational use of raw materials and environmental protection. This requires the improvement of staff support system for mining operations and the interaction of enterprises with universities training mining engineers, aimed at the innovative competencies development of future miners.

Sex differences in gender characteristics of Australian nurses and male engineers: a comparative cross-sectional survey.

Science.gov (United States)

J Fisher, Murray

2011-08-01

There continue to be assumptions within the nursing literature that nursing is synonymous with a feminine sex role identity. A comparative cross-sectional survey consisting of the Bem Sex Role Inventory and the Australian sex role scale was used to determine sex difference in gender characteristics of Australian nurses and with male engineers. A statistically significant difference in femininity was found between all the samples (F((2,908)) = 20.24, p orientation (t = 27.67) and self display (t = 12.42). Whilst differences in expressive characteristics were found between male and female nurses, a similar difference was found between male nurses and male engineers, supporting the notion that male nurses perceive themselves as having feminine characteristics essentially required for nursing.

Computing Infrastructure and Remote, Parallel Data Mining Engine for Virtual Observatories, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — We propose to develop a state-of-the-art data mining engine that extends the functionality of Virtual Observatories (VO) from data portal to science analysis...

Engineering and the Politics of Commensuration in the Mining and Petroleum Industries

OpenAIRE

Jessica M. Smith; Nicole M. Smith

2018-01-01

Engineers and applied scientists form the backbone of the mining and petroleum industries, yet rarely figure in social science accounts of natural resource extraction. This article begins to fill that gap by ethnographically exploring how community conflicts have prompted engineers and applied scientists working in these industries to reconsider the relationship between the surface and subsurface dimensions of their work. To make social concerns on the surface matter to how drilling and extra...

Sustainable application of reciprocating gas engines operating on coal mine methane

Energy Technology Data Exchange (ETDEWEB)

Lee, J.; Teo, T. [Caterpillar China Investment Co., Beijing (China); Tnay, C.H. [Westrac Inc., Beijing (China)

2008-07-01

According to the World Coal Institute, coal provides 25 per cent of worldwide primary energy needs and generates 40 per cent of the world's electricity. China produces the largest amount of hard coal. The anthropogenic release of methane (CH{sub 4}) into the environment is a byproduct of the coal mining process. The global warming potential of this methane continues to draw attention around the world. In particular, China's government has recognized the need for environmental responsibility in the pursuit of greater power production. The Kyoto Protocol requires developed countries to reduce their greenhouse gas emissions and targets must be met within a five-year time frame between 2008 and 2012. Sequestering coal mine methane (CMM) as an alternative fuel for reciprocating gas engine generator sets is a mature and proven technology for greenhouse gas mitigation. Prior to commissioning CMM-fueled power systems, the methane gas composition must be evaluated. An integrated systems approach can then be used to develop a CMM-fueled power project. This paper discussed the sustainable application of reciprocating gas engines operating on coal mine methane. It discussed the Kyoto Protocol, clean development mechanism, and CMM as compared to other fuel sources. It was concluded that there is considerable opportunity for growth in the Asia-Pacific region for electric power applications using CMM. 4 refs., 12 figs.

Computing Infrastructure and Remote, Parallel Data Mining Engine for Virtual Observatories, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — SciberQuest, Inc. proposes to develop a state-of-the-art data mining engine that extends the functionality of Virtual Observatories (VO) from data portal to science...

Impact of pedagogical approaches on cognitive complexity and motivation to learn: Comparing nursing and engineering undergraduate students.

Science.gov (United States)

McComb, Sara A; Kirkpatrick, Jane M

2016-01-01

The changing higher education landscape is prompting nurses to rethink educational strategies. Looking beyond traditional professional boundaries may be beneficial. We compare nursing to engineering because engineering has similar accreditation outcome goals and different pedagogical approaches. We compare students' cognitive complexity and motivation to learn to identify opportunities to share pedagogical approaches between nursing and engineering. Cross-sectional data were collected from 1,167 freshmen through super senior students. Comparisons were made across years and between majors. Overall nursing and engineering students advance in cognitive complexity while maintaining motivation for learning. Sophomores reported the lowest scores on many dimensions indicating that their experiences need review. The strong influence of the National Council Licensure Examination on nursing students may drive their classroom preferences. Increased intrinsic motivation, coupled with decreased extrinsic motivation, suggests that we are graduating burgeoning life-long learners equipped to maintain currency. The disciplines' strategies for incorporating real-world learning opportunities differ, yet the students similarly advance in cognitive complexity and maintain motivation to learn. Lessons can be exchanged across professional boundaries. Copyright © 2016 Elsevier Inc. All rights reserved.

What the coal industry requires from young mining engineers

Energy Technology Data Exchange (ETDEWEB)

Zilligen, K H

1986-04-24

A colliery manager gives his opinions on the requirements of the industry from young graduates of the Technical College of Mining in the Federal Republic of Germany. He suggests that there is a need for young, well educated graduates from colleges and universities; that all young engineers should start their careers in line management; and that technical college education should be operationally relevant. Suggestions are given for improving the current trainee programme at Minster Achenbach colliery.

Experience in the Education of Engineers from Vietnam in the Faculty of Mining and Geoengineering AGH

Science.gov (United States)

Cała, Marek; Borowski, Marek

2018-03-01

The AGH University of Science and Technology collaborates closely with other universities, economic units, governmental and local administrative bodies. International cooperation plays a very important role in the academic research. The AGH University of Science and Technology has signed many collaboration agreements. They aim at multidimensional cooperation in the fields of education and academic research. AGH UST has always focused on collaboration with business and industry. In recent years, the global economy is undergoing massive transformations, what creates new challenges to companies and educational institutions that cater to the needs of industry. The expansion of business enterprises is largely dependent on their employees' expertise, skills and levels of competence. Certified engineers are provided by universities. Therefore, the qualifications of the graduates are determined by the curriculum and teaching methods, as well as the available educational and research facilities. Of equal importance is the qualified academic staff. Human activities in the field of engineering require finding solutions to problems of various nature and magnitude. An engineer's work consists in the design, construction, modification and maintenance of useful devices, processes and systems, using scientific and technical knowledge. In order to design complex engineering solutions, an engineer uses his imagination, experience, analytical skills, logical reasoning and makes conscious use of his knowledge. At the Faculty of Mining and Geoengineering of the AGH University of Science and Technology in Cracow, 15 engineers from Vietnam are studying Mining and Geology at the second-cycle studies (specialization: mine ventilation). The solutions proposed in the field of the engineers' education guarantee that foreign students gain both engineering knowledge and problem-solving skills. Therefore, the study programme was complemented by a series of practical aspects.

Requirements and opportunities for mining engineers in the mining industry abroad

Energy Technology Data Exchange (ETDEWEB)

Albrecht, E

1987-04-09

The decline of the German mining industry and the increasing industrialization of mining is forcing ever greater numbers of young German mining graduates to build their careers abroad. The requirements for this - apart from the technical qualifications are a good knowledge of foreign languages and a readiness to leave Germany for a long time, even for ever. If the young mining graduate accepts these conditions, numerous professional opportunities will open up for him, both with German mining companies with interests abroad, in mining supply companies and consultancy firms and with foreign companies. 6 references.

Clinical Immersion: An Approach for Fostering Cross-disciplinary Communication and Innovation in Nursing and Engineering Students.

Science.gov (United States)

Geist, Melissa J; Sanders, Robby; Harris, Kevin; Arce-Trigatti, Andrea; Hitchcock-Cass, Cary

2018-05-24

A faculty team from nursing and chemical engineering developed a course that brought together students from each discipline for cross-disciplinary, team-based clinical immersion and collaboration. Health care processes and devices are rapidly changing, and nurses are uniquely positioned to be bedside innovators to improve patient care delivery. During each clinical immersion, the student teams rotated through various hospital units where they identified problems and worked together in the university's makerspace (iMaker Space) to design and build prototypes to improve health outcomes. Data from the Critical thinking Assessment Test provided evidence of gains in critical-thinking and problem-solving skills, while the problems identified in the clinical setting and prototypes developed demonstrated the impact of bringing nursing and engineering students together to design innovations. When challenged to identify authentic problems during their clinical immersion, the teams of nursing and engineering students proposed creative solutions and developed commercially viable prototypes.

Mining routinely collected acute data to reveal non-linear relationships between nurse staffing levels and outcomes.

Science.gov (United States)

Leary, Alison; Cook, Rob; Jones, Sarahjane; Smith, Judith; Gough, Malcolm; Maxwell, Elaine; Punshon, Geoffrey; Radford, Mark

2016-12-16

Nursing is a safety critical activity but not easily quantified. This makes the building of predictive staffing models a challenge. The aim of this study was to determine if relationships between registered and non-registered nurse staffing levels and clinical outcomes could be discovered through the mining of routinely collected clinical data. The secondary aim was to examine the feasibility and develop the use of 'big data' techniques commonly used in industry for this area of healthcare and examine future uses. The data were obtained from 1 large acute National Health Service hospital trust in England. Routinely collected physiological, signs and symptom data from a clinical database were extracted, imported and mined alongside a bespoke staffing and outcomes database using Mathmatica V.10. The physiological data consisted of 120 million patient entries over 6 years, the bespoke database consisted of 9 years of daily data on staffing levels and safety factors such as falls. To discover patterns in these data or non-linear relationships that would contribute to modelling. To examine feasibility of this technique in this field. After mining, 40 correlations (pdata (such as the presence or absence of nausea) and staffing factors. Several inter-related factors demonstrated step changes where registered nurse availability appeared to relate to physiological parameters or outcomes such as falls and the management of symptoms. Data extraction proved challenging as some commercial databases were not built for extraction of the massive data sets they contain. The relationship between staffing and outcomes appears to exist. It appears to be non-linear but calculable and a data-driven model appears possible. These findings could be used to build an initial mathematical model for acute staffing which could be further tested. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Technological highwall mining

Energy Technology Data Exchange (ETDEWEB)

Davison, I. [Highwall Systems (United States)

2006-09-15

The paper explores the issues facing highwall mining. Based in Chilhowie, Virginia, American Highwall Systems has developed a highwall mining system that will allow the mining of coal seams from 26 in to 10 ft in thickness. The first production model, AH51, began mining in August 2006. Technologies incorporated into the company's mining machines to improve the performance, enhance the efficiency, and improve the reliability of the highwall mining equipment incorporate technologies from many disciplines. Technology as applied to design engineering, manufacturing and fabrication engineering, control and monitoring computer hardware and software has played an important role in the evolution of the American Highwall Systems design concept. 5 photos.

System catalytic neutralization control of combustion engines waste gases in mining technologies

Science.gov (United States)

Korshunov, G. I.; Solnitsev, R. I.

2017-10-01

The paper presents the problems solution of the atmospheric air pollution with the exhaust gases of the internal combustion engines, used in mining technologies. Such engines are used in excavators, bulldozers, dump trucks, diesel locomotives in loading and unloading processes and during transportation of minerals. NOx, CO, CH emissions as the waste gases occur during engine operation, the concentration of which must be reduced to the standard limits. The various methods and means are used for the problem solution, one of which is neutralization based on platinum catalysts. A mathematical model of a controlled catalytic neutralization system is proposed. The simulation results confirm the increase in efficiency at start-up and low engine load and the increase in the catalyst lifetime.

Mine ventilation engineering

Energy Technology Data Exchange (ETDEWEB)

Hall, C.J.

1981-01-01

This book on mine ventilation covers psychometrics, airflow through roadways and ducts, natural ventilation, fans, instruments, ventilation surveys, auxiliary ventilation, air quality, and planning and economics.

Biotechnical engineering and the use of mining wastes for land restoration

Energy Technology Data Exchange (ETDEWEB)

Norton, P.J.

1988-01-01

Until recently use of minestone as a soil in land reclamation to lowgrade agriculture has been limited because the material is low in plant growth nutrients. Bioengineering can now produce plant growth without even using topsoil in a variety of environments. Use of colliery waste, and other waste materials such as sewage sludge, pelletized refuse, and flue gas desulphurization end products from coal-fired power stations, for restoration can be made very cheap and effective. Because these materials also pose acute disposal problems, their combined use as soilmaking material can often be achieved for haulage costs alone. The recent developments in biotechnical engineering have advanced the possibility for much improved success rates in tree planting using mycorrhizal inoculants. A second area of research using colliery wastes and other waste materials is in restoring mine sites to amenity lakes or wetland. Wet restoration has always been a problem for mining companies where a high ground water table exists and there is the possibility of acid mine water in the restored lake. Recent developments in the use of sewage sludge through the process of eutrophication have made it possible to not only restore mine sites to acceptable lake amenity use, but also to use problematic colliery waste as bulk fill to prepare the geometry of the lakebed in other mines and quarries. With the additional use of wetland environments to create an environmental 'niche' for wildlife many old mining sites can now be confidently restored very cheaply to publicly acceptable use. 15 refs., 2 figs., 2 tabs.

An Approach to Developing Independent Learning and Non-Technical Skills Amongst Final Year Mining Engineering Students

Science.gov (United States)

Knobbs, C. G.; Grayson, D. J.

2012-01-01

There is mounting evidence to show that engineers need more than technical skills to succeed in industry. This paper describes a curriculum innovation in which so-called "soft" skills, specifically inter-personal and intra-personal skills, were integrated into a final year mining engineering course. The instructional approach was…

Basic plans on measures of mine site at the Ningyo-Toge Environmental Engineering Center

International Nuclear Information System (INIS)

2002-04-01

At the Ningyo-Toge and its peripheries, there are some mine relating facilities and apparatuses finishing their actions such as wasted stones and slags accumulation sites, and so on formed by results of searching and mining works of uranium mine carried out from beginning of 1950s by the Nuclear Fuels Corporation and the Power Reactor and Nuclear Fuel Development Corporation, both of which are predecessors of the Japan Nuclear Cycle Development Institute (JNC). These facilities are, at present, adequately maintained and managed by the Ningyo-Toge Environmental Engineering Center, but as resource development of uranium was positioned to a disposal business on JNC, JNC has investigated on optimal measuring methods and testing plans to evaluate their safety under cooperation with other works of JNC, to summarize a draft of the basic plans on measures of mine site'. Here were described two drafts of the 'Basic plans on measures of mine site' summarized on concepts and indications of whole of measures of mine relating facilities sites and of the 'Proof test plan' summarized on testing plans containing concrete measures to obtain basic data and knowledge required for progressing the measures and a proof test. (G.K.)

Integrating Communication into Engineering Curricula: An Interdisciplinary Approach to Facilitating Transfer at New Mexico Institute of Mining and Technology

Science.gov (United States)

Ford, Julie Dyke

2012-01-01

This program profile describes a new approach towards integrating communication within Mechanical Engineering curricula. The author, who holds a joint appointment between Technical Communication and Mechanical Engineering at New Mexico Institute of Mining and Technology, has been collaborating with Mechanical Engineering colleagues to establish a…

Experience in the Education of Engineers from Vietnam in the Faculty of Mining and Geoengineering AGH

Directory of Open Access Journals (Sweden)

Cała Marek

2018-01-01

Full Text Available The AGH University of Science and Technology collaborates closely with other universities, economic units, governmental and local administrative bodies. International cooperation plays a very important role in the academic research. The AGH University of Science and Technology has signed many collaboration agreements. They aim at multidimensional cooperation in the fields of education and academic research. AGH UST has always focused on collaboration with business and industry. In recent years, the global economy is undergoing massive transformations, what creates new challenges to companies and educational institutions that cater to the needs of industry. The expansion of business enterprises is largely dependent on their employees’ expertise, skills and levels of competence. Certified engineers are provided by universities. Therefore, the qualifications of the graduates are determined by the curriculum and teaching methods, as well as the available educational and research facilities. Of equal importance is the qualified academic staff. Human activities in the field of engineering require finding solutions to problems of various nature and magnitude. An engineer’s work consists in the design, construction, modification and maintenance of useful devices, processes and systems, using scientific and technical knowledge. In order to design complex engineering solutions, an engineer uses his imagination, experience, analytical skills, logical reasoning and makes conscious use of his knowledge. At the Faculty of Mining and Geoengineering of the AGH University of Science and Technology in Cracow, 15 engineers from Vietnam are studying Mining and Geology at the second-cycle studies (specialization: mine ventilation. The solutions proposed in the field of the engineers’ education guarantee that foreign students gain both engineering knowledge and problem-solving skills. Therefore, the study programme was complemented by a series of practical

Data-Mining Toolset Developed for Determining Turbine Engine Part Life Consumption

Science.gov (United States)

Litt, Jonathan S.

2003-01-01

The current practice in aerospace turbine engine maintenance is to remove components defined as life-limited parts after a fixed time, on the basis of a predetermined number of flight cycles. Under this schedule-based maintenance practice, the worst-case usage scenario is used to determine the usable life of the component. As shown, this practice often requires removing a part before its useful life is fully consumed, thus leading to higher maintenance cost. To address this issue, the NASA Glenn Research Center, in a collaborative effort with Pratt & Whitney, has developed a generic modular toolset that uses data-mining technology to parameterize life usage models for maintenance purposes. The toolset enables a "condition-based" maintenance approach, where parts are removed on the basis of the cumulative history of the severity of operation they have experienced. The toolset uses data-mining technology to tune life-consumption models on the basis of operating and maintenance histories. The flight operating conditions, represented by measured variables within the engine, are correlated with repair records for the engines, generating a relationship between the operating condition of the part and its service life. As shown, with the condition-based maintenance approach, the lifelimited part is in service until its usable life is fully consumed. This approach will lower maintenance costs while maintaining the safety of the propulsion system. The toolset is a modular program that is easily customizable by users. First, appropriate parametric damage accumulation models, which will be functions of engine variables, must be defined. The tool then optimizes the models to match the historical data by computing an effective-cycle metric that reduces the unexplained variability in component life due to each damage mode by accounting for the variability in operational severity. The damage increment due to operating conditions experienced during each flight is used to compute

Identifying Engineering Students' English Sentence Reading Comprehension Errors: Applying a Data Mining Technique

Science.gov (United States)

Tsai, Yea-Ru; Ouyang, Chen-Sen; Chang, Yukon

2016-01-01

The purpose of this study is to propose a diagnostic approach to identify engineering students' English reading comprehension errors. Student data were collected during the process of reading texts of English for science and technology on a web-based cumulative sentence analysis system. For the analysis, the association-rule, data mining technique…

Mining software specifications methodologies and applications

CERN Document Server

Lo, David

2011-01-01

An emerging topic in software engineering and data mining, specification mining tackles software maintenance and reliability issues that cost economies billions of dollars each year. The first unified reference on the subject, Mining Software Specifications: Methodologies and Applications describes recent approaches for mining specifications of software systems. Experts in the field illustrate how to apply state-of-the-art data mining and machine learning techniques to address software engineering concerns. In the first set of chapters, the book introduces a number of studies on mining finite

Environmental laws for mining activities in Provincia de San Juan (Argentina), gravel mines exploitation

International Nuclear Information System (INIS)

Ramirez, M.; Carrascosa, H.

2007-01-01

This paper analyses San Juan Province - Argentina prevailing environmental legislation for mining activity and gravel mines. The study focuses the subject from a mining engineering point of view. (author)

Fiscal 2000 survey of geological structures overseas. Exchange of engineers with Indonesia (Coal mining technology); 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) Indonesia

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Indonesia rich in coal resources consumed 70-million tons of coal in 1999, which covered 17% of its total energy demand. It is estimated that as much as 120-million tons will be produced in 2005, and it is expected that underground mining will increase. Under such circumstances, Indonesia strongly desires that Japan's underground mining technologies be transferred to Indonesia. For the transfer of technologies especially involving production control and management out of Japan's underground mining technologies, Japan dispatched engineers to Indonesia under a mining engineer exchange project, and received and trained Indonesian engineers. Under the engineer exchange project, five engineers were dispatched to Indonesia and gave lectures and on-site training in the period July 9 through August 5, 2000. Japan received seven engineers, who were given lectures and training at the Ikeshima mining field of Matsushima Coal Mining Company in the period November 12 through December 12, 2000. (NEDO)

FY 1998 annual report on the survey on overseas geological structures. Project for exchanging engineers (coal mining technology area) (Vietnam); 1998 nendo kaigai chishitsu kozo nado chosaa. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) (Vietnam)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project for exchanging engineers has been implemented, in order to improve production and managemental techniques of coal mining engineers in the Asia-Pacific region, promote smooth and efficient projects for surveying overseas geological structures, and facilitate stable supply of overseas coal to Japan. The FY 1998 project was concentrated on Vietnam, to which Japanese coal mining engineers were sent, and from which production management engineers were invited to Japan as trainees. The Japanese engineers sent to Vietnam educated the underground coal mining techniques. The Vietnamese management engineers invited were trained for, e.g., production management techniques (e.g., those for workplaces and organizations) in the Japanese mines, administrative management techniques, and techniques to improve safety and productivity in the mines. Coal Energy Center and Taiheiyo Mining's Kushiro Mine provided training facilities. (NEDO)

Zoning method for environmental engineering geological patterns in underground coal mining areas.

Science.gov (United States)

Liu, Shiliang; Li, Wenping; Wang, Qiqing

2018-09-01

Environmental engineering geological patterns (EEGPs) are used to express the trend and intensity of eco-geological environment caused by mining in underground coal mining areas, a complex process controlled by multiple factors. A new zoning method for EEGPs was developed based on the variable-weight theory (VWT), where the weights of factors vary with their value. The method was applied to the Yushenfu mining area, Shaanxi, China. First, the mechanism of the EEGPs caused by mining was elucidated, and four types of EEGPs were proposed. Subsequently, 13 key control factors were selected from mining conditions, lithosphere, hydrosphere, ecosphere, and climatic conditions; their thematic maps were constructed using ArcGIS software and remote-sensing technologies. Then, a stimulation-punishment variable-weight model derived from the partition of basic evaluation unit of study area, construction of partition state-variable-weight vector, and determination of variable-weight interval was built to calculate the variable weights of each factor. On this basis, a zoning mathematical model of EEGPs was established, and the zoning results were analyzed. For comparison, the traditional constant-weight theory (CWT) was also applied to divide the EEGPs. Finally, the zoning results obtained using VWT and CWT were compared. The verification of field investigation indicates that VWT is more accurate and reliable than CWT. The zoning results are consistent with the actual situations and the key of planning design for the rational development of coal resources and protection of eco-geological environment. Copyright © 2018 Elsevier B.V. All rights reserved.

A Tutorial on Nonlinear Time-Series Data Mining in Engineering Asset Health and Reliability Prediction: Concepts, Models, and Algorithms

Directory of Open Access Journals (Sweden)

Ming Dong

2010-01-01

Full Text Available The primary objective of engineering asset management is to optimize assets service delivery potential and to minimize the related risks and costs over their entire life through the development and application of asset health and usage management in which the health and reliability prediction plays an important role. In real-life situations where an engineering asset operates under dynamic operational and environmental conditions, the lifetime of an engineering asset is generally described as monitored nonlinear time-series data and subject to high levels of uncertainty and unpredictability. It has been proved that application of data mining techniques is very useful for extracting relevant features which can be used as parameters for assets diagnosis and prognosis. In this paper, a tutorial on nonlinear time-series data mining in engineering asset health and reliability prediction is given. Besides that an overview on health and reliability prediction techniques for engineering assets is covered, this tutorial will focus on concepts, models, algorithms, and applications of hidden Markov models (HMMs and hidden semi-Markov models (HSMMs in engineering asset health prognosis, which are representatives of recent engineering asset health prediction techniques.

International exchange project for the engineer exchange project (in coal mine technology area) in fiscal 1998. Overseas workshop; 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The international exchange project for the engineer exchange project (in coal mine technology area) in fiscal 1998, the 'Overseas workshop' has performed exchange in technologies with Australian coal mine engineers. The project refers to the Australian technological levels and needs in coal production, safety control and environment, as well as transfer of the Japanese coal mine technologies. This report summarizes the result of a survey on the engineer exchange project in the coal mine technology area and the possibility of joint researches. The 'overseas workshop' was held in November 1998 for two days in Brisbane City in QLD Province as the 'Japan-Australia coal technology workshop'. The 'Japan-Australia coal technology workshop' gave lectures in five sessions (the basic lecture, Japan-Australia high-speed excavation project, coal mine gas control project, exploration and resources, and development and experience of Japan). It also discussed two themes (mine safety management and rules, and greenhouse effect gases and coal mining). Two coal mines were visited thereafter to deepen the exchange with the Australian coal mine engineers. (NEDO)

URL Mining Using Agglomerative Clustering Algorithm

Directory of Open Access Journals (Sweden)

Chinmay R. Deshmukh

2015-02-01

Full Text Available Abstract The tremendous growth of the web world incorporates application of data mining techniques to the web logs. Data Mining and World Wide Web encompasses an important and active area of research. Web log mining is analysis of web log files with web pages sequences. Web mining is broadly classified as web content mining web usage mining and web structure mining. Web usage mining is a technique to discover usage patterns from Web data in order to understand and better serve the needs of Web-based applications. URL mining refers to a subclass of Web mining that helps us to investigate the details of a Uniform Resource Locator. URL mining can be advantageous in the fields of security and protection. The paper introduces a technique for mining a collection of user transactions with an Internet search engine to discover clusters of similar queries and similar URLs. The information we exploit is a clickthrough data each record consist of a users query to a search engine along with the URL which the user selected from among the candidates offered by search engine. By viewing this dataset as a bipartite graph with the vertices on one side corresponding to queries and on the other side to URLs one can apply an agglomerative clustering algorithm to the graphs vertices to identify related queries and URLs.

Fiscal 1999 international engineer exchange project (Coal mining technology field). Overseas workshop (Australia); 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop (Goshu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the technology exchange with Australian coal mining engineers, the technical levels and needs on coal production, safety and environment in Australia, and the FS result on transfer of Japanese technologies, engineer exchange and joint research in a coal mining technology field. The overseas workshop (Australia) was held on Nov. 9, 1999 (Tues.) in Brisbane, Queensland. The Australia-Japan Technology Exchange Workshop on coal resources and coal mining technology includes 5 sessions (keynote address, trends and issues of coal resource development, coal resources and production technology, coal resources and safety technology, coal resources and environmental problems), and the open forum discussion on innovative technologies for coal mining. 6 Japanese specialists and 11 Australian specialists read papers. After the workshop, the participants visited Liddell Mine in New South Wales to master natural conditions, and production and safety technology levels of Australian coal mines, and to exchange various information with Australian coal mining engineers. (NEDO)

Applicability of gassy mine regulations: Engineering study report

International Nuclear Information System (INIS)

1987-08-01

This study reviewed three bodies of current Mine Safety and Health Administration (MSHA) gassy mine regulations, to address whether the Code of Federal Regulations (CFR) Title 30, Part 57 Safety and Health Standards - Metal and Nonmetal Underground Mines, Section 21-Gassy Mines, or Parts 75 Mandatory Safety Standards - Underground Coal Mines, and Part 77 Mandatory Safety Standards - Surface Coal Mines and Surface Work Areas of Underground Coal Mines, are more applicable to a subsurface repository design. Part 57.21 is determined to be most applicable. There are, however, three sections in Parts 75 and 77 which address certain applicable items in greater detail and, therefore, will provide a more conservative design approach in these areas than Part 57.21, and should be incorporated into the basis for design. Study work also revealed that proposed CFR Title 30, Part 58 Mine Safety and Health - Metal and Nonmetal Standards, will have to be considered during design work if and when these have been promulgated. 9 refs., 1 fig., 1 tab

International exchange project for the engineer exchange project (in coal mine technology area) in fiscal 1998. Overseas workshop; 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The international exchange project for the engineer exchange project (in coal mine technology area) in fiscal 1998, the 'Overseas workshop' has performed exchange in technologies with Australian coal mine engineers. The project refers to the Australian technological levels and needs in coal production, safety control and environment, as well as transfer of the Japanese coal mine technologies. This report summarizes the result of a survey on the engineer exchange project in the coal mine technology area and the possibility of joint researches. The 'overseas workshop' was held in November 1998 for two days in Brisbane City in QLD Province as the 'Japan-Australia coal technology workshop'. The 'Japan-Australia coal technology workshop' gave lectures in five sessions (the basic lecture, Japan-Australia high-speed excavation project, coal mine gas control project, exploration and resources, and development and experience of Japan). It also discussed two themes (mine safety management and rules, and greenhouse effect gases and coal mining). Two coal mines were visited thereafter to deepen the exchange with the Australian coal mine engineers. (NEDO)

Nursing and the Emergence of Egoless Care: A Discussion on Social Engineering in Mental Health.

Science.gov (United States)

Schout, Gert; de Jong, Gideon

2018-02-01

The narrowing of the diverse fields of psychiatry to just the single dimension of the biomedical model has resulted in a situation where professions with a focus on curing (psychiatrists and psychologists) are favoured over those with a focus on caring and encouraging near communities to care for each other (nurses). The social engineering of mental problems leads to a state of helplessness. This paper contributes to an understanding of the barriers to utilise the social resources of people with mental health problems and argues for forms of "indirect social engineering" and "egoless care," and, ultimately, a rediscovery of nursing, using the mental health care in the Netherlands as a case study.

Technical engineers exchange project (coal mine technology field). Training in China; Gijutsusha koryu jigyo (tanko gijutsu bun`ya). Chugoku no kenshu ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Adachi, T. [Japan Coal Energy Center, Tokyo (Japan)

1998-07-01

The paper described JCOAL`s project on the exchange of technical coal engineers of China. In the project on sending of engineers to China in the first term, coal mine engineers of Japan (Taiheiyo Coal Mine, Kushiro Works, Training Center) were sent to the Daitun coal-thermal power plant, Peixuan city, Jiangsu province, in September, 1997 to introduce the production control technology in Japan. They contributed to the heightening of productivity in coal mines in China. Eighteen Chinese participated in the training. Mechanization has been comparatively well in progress, and it was 83% in coal mining and 91% in drilling. The kind of coal is mostly a raw material coal. The stuff members are 30,000, and expert engineers are 4,200. The plant has an output of 130,000 kWh, owns its railroad, is run on the general multiple management, and is largely developing. The project on sending of engineers to China in the last term was carried out in February 1998 for tracing/confirming how the results of the training conducted in September are made the most of and if or not there is something bad and for obtaining the detailed data. A certain degree of promotion and effects were able to be confirmed. A project on training of the head, sub-head, etc. who were invited to Japan to lean production/management control was also carried out in November and December 1997. 1 tab.

Partnership in mining

Energy Technology Data Exchange (ETDEWEB)

Haslam, R

1988-04-01

This paper discusses the benefits resulting from mutual cooperation and information exchange between the UK and USA coal industries. The aim of this cooperation is to promote safe and efficient extraction and profitable use of coal. Advanced mining technologies and mechanisation of the coal mines are some of the results of research cooperation between British Coal and the US Bureau of Mines. In addition, Britain has studied and put into good use the management styles, working practices and pay structure, and mining engineering adopted in the USA.

Mining education in the XXI century: global challenges and prospects

Directory of Open Access Journals (Sweden)

О. И. Казанин

2017-06-01

Full Text Available An analysis of development prospects for the world mining industry is presented, requirements to mining technologies are formulated, as well as key trends of technologic development in the mineral resources complex. The paper demonstrates the role of mining industry and professional education as essential components of sustainable territorial development. Global challenges have been formulated, which must be taken into account when forming general approaches to the development of mining education. Distinctions of mining education in Russia, Germany, USA and other leading mining countries have been analyzed. Professional standards for mining engineers have been reviewed for different countries, along with their relation to educational standards. It has been shown, what role professional communities play in the development of professional education and stimulation of continuous professional development of mining engineers. Authors point out the need for international integration in the issues of training and continuous professional development of mining specialists, as well as international accreditation of educational programs for mining engineers and their certification. Information is presented on international organizations, performing the function of international accreditation of engineering educational programs, history of their establishment and role within the context of economic globalization. The paper contains examples of successful international cooperation and modern integration processes among universities, aimed at unification of requirements and improvement of existing systems of training and continuous professional development of mining engineers.

Fiscal 1998 overseas geological structure survey report on the engineer interchange project (coal mine technology field), Indonesia; 1998 nendo kaigai chishitsu kozo nado chosa gijutsusha koryu jigyo (tanko gijutsu bun'ya), Indonesia hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This project aims at improvement of coal mining technology and productivity in Indonesia by Japanese production control technology and business management technology for underground coal mining, through interchange of coal engineers between Japan and Indonesia. This project is composed of the short- term and long-term dispatch project of engineers to Indonesia, and the training project of Indonesian engineers in Japan. In fiscal 1998, the short-term dispatch was made for the training in Indonesia on underground coal mine development (development planning, pit mouth selection, main gallery design, mining system selection, transport planning, ventilation planning, under-river mining, mine water proofing, drainage). The long-term dispatch was made for contact and negotiation with concerned Indonesian organizations, support of the training project, and collection of information on the trend of Indonesian economy and energy, and the present and trend of the coal industry for conducting smooth and effective engineer interchange. (NEDO)

Mining

Directory of Open Access Journals (Sweden)

Khairullah Khan

2014-09-01

Full Text Available Opinion mining is an interesting area of research because of its applications in various fields. Collecting opinions of people about products and about social and political events and problems through the Web is becoming increasingly popular every day. The opinions of users are helpful for the public and for stakeholders when making certain decisions. Opinion mining is a way to retrieve information through search engines, Web blogs and social networks. Because of the huge number of reviews in the form of unstructured text, it is impossible to summarize the information manually. Accordingly, efficient computational methods are needed for mining and summarizing the reviews from corpuses and Web documents. This study presents a systematic literature survey regarding the computational techniques, models and algorithms for mining opinion components from unstructured reviews.

Mining Foreman School in Dabrowa Gornicza - heir to the Higher Mining School in Kielce

Energy Technology Data Exchange (ETDEWEB)

Ciuk, E

1988-02-01

The first Polish Higher Mining School was founded in 1816 in Kielce. The historical background of its foundation is described, curricula are outlined, prominent professors and graduates named. The significance of this School for Polish geology, mining and metallurgy to the present day is stressed. The School was closed in 1826 and the next Mining School to contine its traditions was instituted not earlier than in 1889 in Dabrowa Gornicza. It was also known as the Mine Foreman or Mine Deputy School (Sztygarka). This School was closed in 1905, reopened in 1910 and closed again in 1914. After Poland regained independence in 1919 the School flourished for 20 years. During the Second World War the teaching staff and student body were decimated and facilities destroyed. After 1945 the School was rebuilt and developed into an engineering school as a branch of the Academy of Mining and Metallury in Cracow by 1968 and a branch of the Silesian Politechnical between 1968 and 1984. In 1985 the School was taken over by the Ministry of Mining and Power Engineering and reorganized as a mining trade school. The Mining School in Dabrowa Gornicza, where several prominent professors of geology and managers of Polish geological and mining enterprises began their careers, contributed greatly to the development of geology in Poland. 12 refs.

Engineering and the Politics of Commensuration in the Mining and Petroleum Industries

Directory of Open Access Journals (Sweden)

Jessica M. Smith

2018-03-01

Full Text Available Engineers and applied scientists form the backbone of the mining and petroleum industries, yet rarely figure in social science accounts of natural resource extraction. This article begins to fill that gap by ethnographically exploring how community conflicts have prompted engineers and applied scientists working in these industries to reconsider the relationship between the surface and subsurface dimensions of their work. To make social concerns on the surface matter to how drilling and extraction would happen, they tried to make these two domains legible to one another. Using mapping and modeling, they created new techniques for making “social” concerns visible and actionable by field operators, even as they expressed reservations about unduly flattening the inherent complexity of human thought, action, and emotion in the process. While these practices opened space for other engineers and applied scientists to incorporate the concerns of nearby residents into their plans and practices, they also raised questions about the appropriateness of commensuration, or the process of translation through which things and values are made comparable.

Earth Science Mining Web Services

Science.gov (United States)

Pham, Long; Lynnes, Christopher; Hegde, Mahabaleshwa; Graves, Sara; Ramachandran, Rahul; Maskey, Manil; Keiser, Ken

2008-01-01

To allow scientists further capabilities in the area of data mining and web services, the Goddard Earth Sciences Data and Information Services Center (GES DISC) and researchers at the University of Alabama in Huntsville (UAH) have developed a system to mine data at the source without the need of network transfers. The system has been constructed by linking together several pre-existing technologies: the Simple Scalable Script-based Science Processor for Measurements (S4PM), a processing engine at he GES DISC; the Algorithm Development and Mining (ADaM) system, a data mining toolkit from UAH that can be configured in a variety of ways to create customized mining processes; ActiveBPEL, a workflow execution engine based on BPEL (Business Process Execution Language); XBaya, a graphical workflow composer; and the EOS Clearinghouse (ECHO). XBaya is used to construct an analysis workflow at UAH using ADam components, which are also installed remotely at the GES DISC, wrapped as Web Services. The S4PM processing engine searches ECHO for data using space-time criteria, staging them to cache, allowing the ActiveBPEL engine to remotely orchestras the processing workflow within S4PM. As mining is completed, the output is placed in an FTP holding area for the end user. The goals are to give users control over the data they want to process, while mining data at the data source using the server's resources rather than transferring the full volume over the internet. These diverse technologies have been infused into a functioning, distributed system with only minor changes to the underlying technologies. The key to the infusion is the loosely coupled, Web-Services based architecture: All of the participating components are accessible (one way or another) through (Simple Object Access Protocol) SOAP-based Web Services.

Mined salt storage feasibility: Engineering study report

International Nuclear Information System (INIS)

1987-07-01

This study addresses a method of eliminating the surface storage of mined salt at the Deaf Smith repository site. It provides rough estimates of the logistics and costs of transporting 3.7 million tons of salt from the repository to the salt disposal site near Carlsbad, New Mexico and returning it to the repository for decommissioning backfill. The study assumes that a railcar/truck system will be installed and that the excavated salt will be transported from the repository to an existing potash mine located near Carlsbad, New Mexico approximately 300 miles from the repository. The 3.7 million tons of salt required for repository decommissioning backfill can be stored in the potash mines along with the excess salt, with no additional capital costs required for either a railcar or a truck transportation system. The capital cost for facilities to reclaim the 3.7 million tons of salt from the potash mine is estimated to be $4,400,000 with either a rail or truck transportation system. Segregating the 3.7 million tons of backfill salt in a surface storage area at the potash mine requires a capital cost of $13,900,000 with a rail system or $11,400,000 with a truck system. Transportation costs are estimated at $0.08/ton-mile for rail and $0.13/ton-mile for truck. 2 figs., 5 tabs

Long-term experience in salt mining and experience in salt mine decommissioning - a chance for ultimate storage?

International Nuclear Information System (INIS)

Sitz, P.; Rauche, H.

2003-01-01

The author discusses similarities between salt mining and ultimate storage and the possibility of using abandoned salt mines as ultimate storage site. He states that with all the numeric prediction tools now available, expert knowledge of mining engineers is still indispensable [de

Department of Mining and Geotechnics – 50 th Anniversary

Directory of Open Access Journals (Sweden)

Ïurove Juraj

2002-12-01

Full Text Available The Mining faculty of the Technical High School in Košice (now BERG Faculty of the Technical University of Košice was found in 1952. In the first years this school consisted only of three Faculties, namely the Faculty of Mining, Faculty of Metallurgy and Faculty of Mechanical Engineering with few of Departments. Teaching and research activities at the Mining Faculty from begining has been based on the staff members of the Mining Department (now Department of Mining and Geotechnics. During the last 50 years Department of Mining has been growing in terms of the number of subject, laboratories, staff members, students etc., and finished their diploma in total 1101 mining engineers At the begin of this period Department was ment to meet the needs of the Slovak mineral industry relating to the education of engineers and research works in the following areas:,underground mining of mineral deposits, open pit mine, stability problems , rock mechanics, design and construction of mines, but now also in computing and information technologies. At present the Department offers courses in various fields of mining and geotechnics, which cover a very wide range of technical problems arising in mining industry and geotechnical praxis, including rescue, fire and safety course. Full-time study at the Department takes five years and leads to a Master´s degree of mining engineering. The study program comprises also an obligatory practical work. The students´practical training is usually divided into 2 terms each of 2-3 weeks duration. In the last semester the students are preparing their Master´s degree thesis.

Flexible automated systems of real time mining operation management: concepts, architecture, models of network engineering for data transmission and processing

Energy Technology Data Exchange (ETDEWEB)

Markhasin, A.B.

1987-11-01

Since the mid 1960's considerable effort has been invested by the mining industry and its research institutions and by universities to create real time mining management automation systems. Some of the shortcomings which still persist in realizing the efficiency such systems can offer are due to objective and subjective factors within and outside the management systems: the creation of the component base, automation equipment, and computer technology, on the one hand, and the organization, process, engineering, and coordination of mining work on the other. This review addresses several of these shortcomings with recommendations for their solution in a primary and systematic way and suggests methods for the implementation of microprocessors and a network of flexible data transmission and processing facilities for both surface and underground mining.

Ancient and medieval mining engineering in the southwest of the iberian peninsula; Ingenieria minera antigua y medieval en el suroeste iberico

Energy Technology Data Exchange (ETDEWEB)

Perez Macias, J. A.; Delgado Dominguez, A.

2011-07-01

This work provides a summary of our knowledge about the old mining works in the southwest of the Iberian Peninsula. Thus in the light of recent investigations, always bearing in mind the descriptions of these ancient mining works made by engineers and geologists in the XIX and the XX centuries, we have been able to systematize the prehistoric and proto historic mining works and provide evidence for the existence of underground mining during these remote times, when it was believed that only open-cast extraction took place. In the same way we have looked into all the types of mining works documented from the Roman period to the present day and been able to distinguish a continued use of these during the Middle Ages at a time when, until recently, they were considered hardly to exist. (Author) 41 refs.

Mapping For Literature Conceptual And Theoretical Framework And Methodology Case Of Hot Deep Mining Ventilation Engineering Evaluation And Design

Directory of Open Access Journals (Sweden)

Peter M. Lukonde

2017-09-01

Full Text Available The paper reports the layout of a mapping process for literature theoretical and conceptual framework and methodology for mining ventilation engineering evaluation design and methodology for a hot deep mine. The purpose of mine ventilation is to provide suitable environmental conditions in working places that promote comfort and efficiency as well as the safety and health of underground personnel. The objectives addressed in this paper include a evaluation of a current mine ventilation system for a hot deep-level mine taking into account the existing ventilation system infrastructure for building of a mine ventilation baseline parametric database for subsequent end of life mine ventilation design and b design of the extension end of mine life ventilation system taking into account increased production high geothermic gradient and subsequent increase in depth of mining. The methodology used in evaluating an existing underground mine ventilation system and designing the extension end of mine life ventilation system employed three stages i Literature mapping to identify authors titles and technical papers at global regional and nationaldistrict scales relevant to the research ii Conceptual and theoretical framework mapping to extract a kernel or core of concepts hypotheses and theories from the literature map to drive the formation of methods of implementation and iii Methodology and implementation mapping to direct and control the processes of data collection analysis and interpretation. A sample case study of a deep-level underground mine has been used in this paper to provide examples of data collection data analysis and interpretation key findings and results discussion and what is new conclusions and recommendations when the proposed mapping process is employed.

Biodiversity loss from deep-sea mining

OpenAIRE

C. L. Van Dover; J. A. Ardron; E. Escobar; M. Gianni; K. M. Gjerde; A. Jaeckel; D. O. B. Jones; L. A. Levin; H. Niner; L. Pendleton; C. R. Smith; T. Thiele; P. J. Turner; L. Watling; P. P. E. Weaver

2017-01-01

The emerging deep-sea mining industry is seen by some to be an engine for economic development in the maritime sector. The International Seabed Authority (ISA) – the body that regulates mining activities on the seabed beyond national jurisdiction – must also protect the marine environment from harmful effects that arise from mining. The ISA is currently drafting a regulatory framework for deep-sea mining that includes measures for environmental protection. Responsible mining increasingly stri...

Survey of nine surface mines in North America. [Nine different mines in USA and Canada

Energy Technology Data Exchange (ETDEWEB)

Hayes, L.G.; Brackett, R.D.; Floyd, F.D.

1981-01-01

This report presents the information gathered by three mining engineers in a 1980 survey of nine surface mines in the United States and Canada. The mines visited included seven coal mines, one copper mine, and one tar sands mine selected as representative of present state of the art in open pit, strip, and terrace pit mining. The purpose of the survey was to investigate mining methods, equipment requirements, operating costs, reclamation procedures and costs, and other aspects of current surface mining practices in order to acquire basic data for a study comparing conventional and terrace pit mining methods, particularly in deeper overburdens. The survey was conducted as part of a project under DOE Contract No. DE-AC01-79ET10023 titled The Development of Optimal Terrace Pit Coal Mining Systems.

Mining Department computer systems

Energy Technology Data Exchange (ETDEWEB)

1979-09-01

Describes the main computer systems currently available, or being developed by the Mining Department of the UK National Coal Board. They are primarily for the use of mining and specialist engineers, but some of them have wider applications, particularly in the research and development and management statistics fields.

Underground coal mine air quality in mines using disposable diesel exhaust filter control devices

Energy Technology Data Exchange (ETDEWEB)

Carlson, D.H.; Johnson, J.H.; Bagley, S.T.; Gratz, L.D. [Michigan Technological University, Houghton, MI (United States). Dept. of Mining Engineering

1996-07-01

As part of a collaborative study with the US Bureau of Mines, in-mine studies have been conducted to assess the effects of a low temperature disposable diesel exhaust filter. The mines have been designed as mines R and S in US Bureau of Mines publications. Each mine operated three to four Jeffrey 4110 ramcar haulage vehicles in the test section. The ramcars were equipped with MWM D916-6 diesel engines, rated at 74.6 kW (100 hp), and were operated for 3 days with the disposal diesel exhaust filter and 2 days without in both mines. Average diesel particulate matter control efficiencies, as measured by samplers located on the coal haulage vehicle, were 80% in mine R and 76% in mine S. Diesel particulate matter average control efficiencies, as measured in the diesel engine tailpipe, were 52% for mine R (for two ramcar vehicles) and 86% for mine S (for four ramcar vehicles). The air quality index control efficiencies, as measured by samplers located on the coal haulage vehicle were 48% in mine R and 51% in mine S. The exhaust quality index control efficiencies from tailpipe measurements were 45% for mine R and 63% for mine S. As measured by a high volume sampler in mine S, diesel particulate matter and associated organics and mutagenic activity were reduced approximately 50% with the use of the disposal diesel exhaust filter. Similar results were found with modified personal samplers in mine R. Little effect was found on relative removal of semivolatile organics. The disposal diesel exhaust filter resulted in about a 50% reduction in the most volatile polynuclear hydrocarbons; however, there appeared to be little effect on the less volatile polynuclear hydrocarbons. The disposable diesel exhaust filter appears to be very effective in reducing the levels of all the diesel exhaust particulate components, while having minor effects on the relative breakdown of the individual components of the particulate. 30 refs., 13 figs., 4 tabs.

Numerical simulation of a multi-reef tabular mining layout in a South African platinum mine

CSIR Research Space (South Africa)

Napier, JAL

2008-09-01

Full Text Available Some of the key problems facing rock engineers on mines in the Bushveld Complex are design of stable panel spans, optimum pillar dimensions and assessing hangingwall stability. A particularly difficult problem is encountered in some mines where...

Disposal facility building also is mining engineering. Germany can tap into this expertise and planning potential; Endlagerbergbau ist auch Bergbau. Erfahrungs- und Planungspotential in Deutschland

Energy Technology Data Exchange (ETDEWEB)

Hucke, Andreas; Kohl, Nadine; Scior, Carsten; Gutberlet, Daniela [DMT GmbH und Co.KG, Essen (Germany)

2015-07-01

The conventional mining industry has a rich tradition and as mining is practised all over the world under a whole range of different conditions the industry has witnessed all kinds of technical developments aimed at controlling strata behaviour and winning the target mineral as efficiently as possible. The proposed use of deep geological deposits as disposal facilities for nuclear waste has transformed the role of the mining Industry and instead of extracting material from the ground mining engineers are now focussing more on how to store waste material safely deep below the earth's surface. Nevertheless, this new remit retains many of the key aspects of conventional mining and the experience that the industry has built up over the years Is still of vital importance when it comes to selecting a suitable disposal site and planning a final waste disposal facility in deep geological formations. These processes benefit from the support of specialists with a mining engineering background, as this can help to avoid unnecessary delays, additional costs and potential damage to public image. The following paper describes some of the expertises and methods developed by the conventional extraction industry that are also of relevance for the construction of disposal facilities.

Development of a Google-based search engine for data mining radiology reports.

Science.gov (United States)

Erinjeri, Joseph P; Picus, Daniel; Prior, Fred W; Rubin, David A; Koppel, Paul

2009-08-01

The aim of this study is to develop a secure, Google-based data-mining tool for radiology reports using free and open source technologies and to explore its use within an academic radiology department. A Health Insurance Portability and Accountability Act (HIPAA)-compliant data repository, search engine and user interface were created to facilitate treatment, operations, and reviews preparatory to research. The Institutional Review Board waived review of the project, and informed consent was not required. Comprising 7.9 GB of disk space, 2.9 million text reports were downloaded from our radiology information system to a fileserver. Extensible markup language (XML) representations of the reports were indexed using Google Desktop Enterprise search engine software. A hypertext markup language (HTML) form allowed users to submit queries to Google Desktop, and Google's XML response was interpreted by a practical extraction and report language (PERL) script, presenting ranked results in a web browser window. The query, reason for search, results, and documents visited were logged to maintain HIPAA compliance. Indexing averaged approximately 25,000 reports per hour. Keyword search of a common term like "pneumothorax" yielded the first ten most relevant results of 705,550 total results in 1.36 s. Keyword search of a rare term like "hemangioendothelioma" yielded the first ten most relevant results of 167 total results in 0.23 s; retrieval of all 167 results took 0.26 s. Data mining tools for radiology reports will improve the productivity of academic radiologists in clinical, educational, research, and administrative tasks. By leveraging existing knowledge of Google's interface, radiologists can quickly perform useful searches.

Coastal mining

Science.gov (United States)

Bell, Peter M.

The Exclusive Economic Zone (EEZ) declared by President Reagan in March 1983 has met with a mixed response from those who would benefit from a guaranteed, 200-nautical-mile (370-km) protected underwater mining zone off the coasts of the United States and its possessions. On the one hand, the U.S. Department of the Interior is looking ahead and has been very successful in safeguarding important natural resources that will be needed in the coming decades. On the other hand, the mining industry is faced with a depressed metals and mining market.A report of the Exclusive Economic Zone Symposium held in November 1983 by the U.S. Geological Survey, the Mineral Management Service, and the Bureau of Mines described the mixed response as: “ … The Department of Interior … raring to go into promotion of deep-seal mining but industrial consortia being very pessimistic about the program, at least for the next 30 or so years.” (Chemical & Engineering News, February 5, 1983).

Development and application of characteristic database for uranium mining and metallurgy in the library of Beijing Research Institute of Chemical Engineering and Metallurgy

International Nuclear Information System (INIS)

Gao Renxi

2012-01-01

Beijing Research Institute of Chemical Engineering and Metallurgy (BRICEM) is a multi disciplinary comprehensive research institute engaged in uranium mining, engineering design and related material researches. After 53 years of researches and development, BRICEM has accumulated a plenty of valuable data and resources. By analyzing the actual conditions of BRICEM's technological database, this thesis aims to propose the idea of building a characteristic database for uranium mining and metallurgy. It gives an in-depth analysis on content design, development status and problems of database development, in order to come up with solutions to these problems, as well as suggestions on the future development plans of the characteristic database. (author)

Course Design and Student Responses to an Online PBL Course in 3D Modelling for Mining Engineers

Science.gov (United States)

McAlpine, Iain; Stothard, Phillip

2005-01-01

To enhance a course in 3D Virtual Reality (3D VR) modelling for mining engineers, and to create the potential for off campus students to fully engage with the course, a problem based learning (PBL) approach was applied to the course design and all materials and learning activities were provided online. This paper outlines some of the theoretical…

30 CFR 77.1105 - Internal combustion engines; fueling.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Internal combustion engines; fueling. 77.1105 Section 77.1105 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE... COAL MINES Fire Protection § 77.1105 Internal combustion engines; fueling. Internal combustion engines...

Swedish mines. Underground exploitation methods

International Nuclear Information System (INIS)

Paucard, A.

1960-01-01

Between 1949 and 1957, 10 engineers of the Mining research and exploitation department of the CEA visited 17 Swedish mines during 5 field trips. This paper presents a compilation of the information gathered during these field trips concerning the different underground mining techniques used in Swedish iron mines: mining with backfilling (Central Sweden and Boliden mines); mining without backfilling (mines of the polar circle area). The following techniques are described successively: pillar drawing and backfilled slices (Ammeberg, Falun, Garpenberg, Boliden group), sub-level pillar drawing (Grangesberg, Bloettberget, Haeksberg), empty room and sub-level pillar drawing (Bodas, Haksberg, Stripa, Bastkarn), storage chamber pillar drawing (Bodas, Haeksberg, Bastkarn), and pillar drawing by block caving (ldkerberget). Reprint of a paper published in Revue de l'Industrie Minerale, vol. 41, no. 12, 1959 [fr

Using a nursing balanced scorecard approach to measure and optimize nursing performance.

Science.gov (United States)

Jeffs, Lianne; Merkley, Jane; Richardson, Sandy; Eli, Jackie; McAllister, Mary

2011-04-01

The authors give an overview of one healthcare organization's experience in developing a nursing strategic plan and nursing balanced scorecard (NBS) using a focused planning process involving strategy mapping. The NBS is being used at this organization to manage the nursing strategic plan by leveraging and improving nursing processes and organizational capabilities as required, based on data and transparent communication of performance results to key stakeholders. Key strategies and insights may help other nurse leaders in developing or refining strategic approaches to measuring nursing performance. Vital to the success of an organization's strategic plan are ongoing endorsement, engagement and visibility of senior leaders. Quality of decisions made depends on the organization's ability to collect data from multiple sources using standardized definitions, mine data and extract them for statistical analysis and effectively present them in a compelling and understandable way to users and decision-makers.

40 years Becker Mining Systems - from small business to internationally successful mining supplier; 40 Jahre Becker Mining Systems - vom Kleinbetrieb zum international erfolgreichen Bergwerksausruester

Energy Technology Data Exchange (ETDEWEB)

Anon.

2004-11-01

Becker Mining Systems was founded in 1964 by Walter Becker, a mining engineer at Maybach coal mine in Friedrichsthal. On the 40th birthday party his son, Dr Franz Becker, reviewed the company history. Other felicitators were Dr. Georgi, Minister for Economic Affairs in Saarland, Dr. Walter-Borjahns, State Secretary in the Ministry of Economic Affairs and Labor in North Rhine-Westphalia, and Dr. Eikhoff, member of board of directors of DSK. (uke)

[A Study of the Evidence-Based Nursing Practice Competence of Nurses and Its Clinical Applications].

Science.gov (United States)

Hsu, Li-Ling; Hsieh, Suh-Ing; Huang, Ya-Hsuan

2015-10-01

Nurses must develop competence in evidence-based nursing in order to provide the best practice medical care to patients. Evidence-based nursing uses issue identification, data mining, and information consolidation from the related medical literature to help nurses find the best evidence. Therefore, for medical institutions to provide quality clinical care, it is necessary for nurses to develop competence in evidence-based nursing. This study aims to explore the effect of a fundamental evidence-based nursing course, as a form of educational intervention, on the development of evidence-based nursing knowledge, self-efficacy in evidence-based practice activities, and outcome expectations of evidence-based practice in nurse participants. Further the competence of these nurses in overcoming obstacles in evidence-based nursing practice. This quasi-experimental study used a pre-post test design with a single group of participants. A convenience sample of 34 nurses from a municipal hospital in northern Taiwan received 8 hours of a fundamental evidence-based nursing course over a two-week period. Participants were asked to complete four questionnaires before and after the intervention. The questionnaires measured the participants' basic demographics, experience in mining the medical literature, evidence-based nursing knowledge, self-efficacy in evidence-based practice activities, outcome expectations of evidence-based practice, competence in overcoming obstacles in evidence-based nursing practice, and learning satisfaction. Collected data was analyzed using paired t, Wilcoxon Signed Rank, and McNemar tests to measure the differences among participants' evidence-based nursing knowledge and practice activities before and after the workshop. The nurses demonstrated significantly higher scores from pre-test to post-test in evidence-based nursing knowledge II, self-efficacy in evidence-based nursing practice activities, and outcome expectations of evidence-based practice

Application of Discrete EventSimulation in Mine Production Forecast*

African Journals Online (AJOL)

Michael

2016-06-01

Jun 1, 2016 ... Mine production forecast is pertinent to mining as it serves production ... Besides the inability of this method to mimic the .... management and truck operators understood the ..... Mining Engineering Handbook, Hartman, H. L..

An engineering geological investigation of ground subsidence above the Huntly East Mine

Energy Technology Data Exchange (ETDEWEB)

Kelsey, P.I.

1987-10-01

Ground subsidence above the Huntly East Mine at the N.Z.E.D. Hostel has affected an area of approximately seven hectares with measured settlements of over 800mm. Extensive damage was suffered by most buildings and services of the hostel complex To determine the cause(s) and mechanism(s) of the subsidence, site and laboratory investigations were undertaken. Site investigations included core and wash drilling, geophysical borehole logging, dutch cone penetrometer soundings plus piezometer installation and monitoring. Laboratory investigations included one dimensional consolidation and permeability testing, SEM fabric studies, XRD and chemical tests for clay mineralogy, and determinations of Atterberg Limits and grain size distributions. The mine overburden geology at the site consists of a 35 to 60m thick sequence of mudstones and coal seams of the Te Kuiti Group (Eocene to Oligocene), and overlain by a 50 to 70m thick succession of saturated sands, silts and gravels of the Tauranga Group (Pliocene to Holocene). Within the Tauranga Group three aquifers are present. The engineering geological model considered most likely to explain the subsidence is mine roof collapse causing void migration to near the top of the Te Kuiti Group sequence resulting in drainage and depressurising of aquifers at the base of the Tauranga Group. Aquifer depressurisation is considered likely to cause consolidation within both the aquifer and aquitards associated with it. Back-analyses of the dewatering consolidation model in terms of both magnitude and rates of settlement are consistent with observed values. A finite difference numerical analysis was developed for estimations of settlement rates. 98 refs., 67 figs., 12 tabs.

Efficacy Evaluation of Current and Future Naval Mine Warfare Neutralization Method

Science.gov (United States)

2016-12-01

ENGINEERING APPROACH Numerous systems engineering process models were considered for this study including the Waterfall , Spiral, and “Vee” models . Given the... model based systems engineering, design of experiments, requirements analysis, mine warfare, MIW, mine countermeasures, MCM, littoral combat ship, LCS...E. IMPLEMENTATION IN SIMULATION MODEL .............................47 VII. MODELING AND SIMULATION ARCHITECTURE ..................................49

The motivational needs of primary health care nurses to acquire ...

African Journals Online (AJOL)

Karien Jooste

for a significant part of service delivery in the health system. Professional nurses' .... motivational needs of PHC nurses to acquire power in the workplace at mine clinic .... recognition through rewards and status (Jooste, 2009, p. 165). 10.1.1.

Experiencing professional strains of nurses, radiation engineers and physicians working at the Institute of oncology in Ljubljana

International Nuclear Information System (INIS)

Skufca Smrdel, A.C.

2003-01-01

Background. Since 1974 the term burnout is used in psychology. Burnout describes the end result of stress and has been described by Maslach comprising three basic components: emotional exhaustion, depersonalization and low personal accomplishment. In this paper we would like to describe some aspects of burnout experiences of the employees of the Institute of Oncology in Ljubljana. Subjects and methods. We used Questionnaire of professional stress, created by Zunter Nagy and Kocmur. In our research 137 health workers from four professional groups participated: physicians, graduated nurses, nurses and radiation engineers, representing 38% of all employees. Results. We found out that in the experience the professional stressof all four professional groups is relatively equalized. The most prominent feelings are of fatigue, irritability and work overload. There were no signs of depersonalization - as described by Maslach - reported in our group. In nurses and in radiation engineers a distress is significantly more often displayed due to poorer personal income and poorer material status. Nurses reported significantly more often the intention to change work position (51%), institution (57%) or job (47%). Conclusions. Workstress impacts on the experience and on the thought patterns in those participating in the study. We can describe those signs as burnout signs. However, there are more new questions opening in the future as well as the need to a longitudinal approach to the research of this more and more prominent field. (author)

Construction over abandoned mine workings

Energy Technology Data Exchange (ETDEWEB)

Healy, P R; Head, J M

1984-01-01

Guidance is given for engineers involved with the planning and development of sites previously undermined for coal and other minerals. Past methods of mining employed in Britain are described, and their short- and long-term effects on surface stability are assessed. Where modern methods of mining are relevant, or where structural design techniques for the surface effects of mining can be applied, these are included for illustration and completeness. Additional objectives over and above those for conventional site investigations are identified, and details are provided for the planning and execution of a mining investigation. Techniques for consolidation of old mine workings and remedial measures for mine shafts are described. Foundation design options are included for cases where expected ground movements can be accommodated. A comprehensive guide to sources of information on previous mining is presented, together with an example of a specification suitable for the consolidation of old shallow mine workings. (50 refs.)

Biological effects of chronic inhalation of coal mine dust and/or diesel engine exhaust in rodents

International Nuclear Information System (INIS)

Karagianes, M.T.; Palmer, R.F.; Stuart, B.O.; Zwicker, G.M.; Teats, D.

1979-01-01

Rats were killed at 4, 8, 16, and 20 mo after the start of exposures to inhaled high-CWP bituminous coal mine dust separately and combined with unscrubbed exhaust fumes from a diesel engine operated under load-rpm cycling. General health and hematologic parameters were normal. Lung lesions and accumulations of particulate matter increased with length and type of exposure; however, no animals have developed lung tumors or precancerous tissue changes up to 16 mo postexposure

Variation in job titles within the nursing workforce.

Science.gov (United States)

Leary, Alison; Maclaine, Katrina; Trevatt, Paul; Radford, Mark; Punshon, Geoffrey

2017-12-01

The work of specialist nursing has been under scrutiny for many years in the UK due to a perception that it is not cost-effective. A common issue is the lack of consistency of job titles, which causes confusion to the public, employing organisations, colleagues and commissioners of services. Lack of consistency has implications for the wider perception of advanced specialist practice in the worldwide community and the workforce more generally. This study aims to understand the variation in job titles in the UK population. A pre-existing data set of accrued studies into the work of nurses working in specialisms was mined for insight (N = 17,960). This study used knowledge discovery through data and descriptive statistics to perform secondary analysis. Mining these data revealed 595 job titles in use in 17,960 specialist posts once the specialism had been removed. The most commonly used titles were Clinical Nurse Specialist, Nurse Specialist/Specialist Nurse, Advanced Nurse Practitioner and Nurse Practitioner. There were three other primary groupings. These were variants with a specialist or technical prefix of suffix, for example Nurse Endoscopist, variants of seniority such as trainee, senior nurse for [specialism] or variants of function such as Nurse Prescriber. The clustering was driven primarily by pay band. A total of 323 posts were recorded as holding titles such as Advanced Nurse Practitioner or Specialist Nurse who were not registered with the Nursing & Midwifery Council. In this data set, there is a large array of titles, which appear to have little relationship with other factors like education. This is confusing to the public, employers and those commissioning services. It also demonstrates that the previous assumptions by Council for Healthcare Regulatory Excellence that advanced practice labels are associated with career progression are unsound and should be addressed by the regulator. © 2017 John Wiley & Sons Ltd.

Opportunities and Challenges in Deep Mining: A Brief Review

Directory of Open Access Journals (Sweden)

Pathegama G. Ranjith

2017-08-01

Full Text Available Mineral consumption is increasing rapidly as more consumers enter the market for minerals and as the global standard of living increases. As a result, underground mining continues to progress to deeper levels in order to tackle the mineral supply crisis in the 21st century. However, deep mining occurs in a very technical and challenging environment, in which significant innovative solutions and best practice are required and additional safety standards must be implemented in order to overcome the challenges and reap huge economic gains. These challenges include the catastrophic events that are often met in deep mining engineering: rockbursts, gas outbursts, high in situ and redistributed stresses, large deformation, squeezing and creeping rocks, and high temperature. This review paper presents the current global status of deep mining and highlights some of the newest technological achievements and opportunities associated with rock mechanics and geotechnical engineering in deep mining. Of the various technical achievements, unmanned working-faces and unmanned mines based on fully automated mining and mineral extraction processes have become important fields in the 21st century.

Exploration and mining - Report 800C. Predevelopment studies for mine methane management and utilization

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Since 1999 Japan and Australia have been engaged in a 5-year predevelopment study of mine methane management and utilization. The effort aims to develop a technique to recover and utilize the greenhouse gas that escapes during coal mining for a decrease in the environmental impact of coal mining and to develop a technique to simulate the behavior of gas during coal mining. Understanding gas behavior will be useful in formulating a plan for optimum mine methane management and utilization in a newly developed mining zone. Technology transfer and interchangeability were considered and the Hunter Valley, New South Wales, was chosen as the experiment site. Tasks to discharge in fiscal 2000 were (1) collection of data on resources, technology, and the trend of Government policy and regulations, (2) measurement of stress and gas permeability and the assessment of mechanical strength of rock and coal at specified spots in the mining zone, (3) 3-dimensional gasping of the Wambo coal mine geography from the standpoints of geology and civil engineering, grasping of gas characteristics, and modelling and (4) the development of gas and rock behavior grasping technology for use during coal mining. (NEDO)

Work Processes, Role Conflict, and Role Overload: The Case of Nurses and Engineers in the Public Sector.

Science.gov (United States)

Bacharach, Samuel B.; And Others

1990-01-01

Study of five sets of work process variables and their relationship to role conflict and overload among public sector nurses and engineers found managerial strategies appropriate for minimizing role conflict not necessarily appropriate for minimizing role overload. Some work process predictors may be similar across professions, and managerial…

Fiscal 1999 engineer exchange project (field of coal mining technology), international exchange project. Domestic workshop; 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kokunai workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The domestic workshop invites Japanese engineers and engineers from coal producing countries for the exchange of coal mining technologies and aims to substantiate and facilitate the dispatching and receiving of engineers under training programs. The main subject of the Asia-Pacific coal technology workshop was 'Coal for the 21st century - resources and technology,' and there were two sessions held on September 8, titled 'Trends and tasks of coal resources exploitation' and 'Coal resources and production technology.' Lectures were delivered by five overseas and five Japanese coal engineering experts. On September 9, nine essays were presented concerning 'Coal resources and security problems' and 'Coal resources and environmental problems.' In addition, a panel discussion was held, titled 'Coal resources assessment and technology.' Importance was emphasized of the correct assessment of the magnitude of resources, development of probing technologies to collect more detailed information, improvement of digging speeds applicable to faces for large and high-efficiency mining, development of coal mining technologies for increased recovery, etc. Information was exchanged on various occasions and partnership was enhanced between the participants to the advantage of engineer exchanging projects in the future. (NEDO)

9th Mining and metallurgy international congress, Leon, 24-28 May 1994

International Nuclear Information System (INIS)

1994-01-01

The 9th Mining and Metallurgy International Congress had 201 communications. These was articulated into 4th areas: 1.- Geological resources management and profit: 1.1- Geological and mining research on geologic resources. 1.2.- Non energetic mineral resources exploitation. 1.3- Hydro-geologic and geothermia resources. 1.4- Geologic resources and planning. 2.- Energy: 2.1.- Energetic mining.- 2.2 Oil and gas. 2.3.- Electricity production and distribution. 2.4.- Coal clean technologies. 2.5.- Energetic management. 3.- Material engineering: 3.1.- Minerallurgia and metallurgic processes. 3.2- Industrial minerals and ornamental 10cks. 3.3 .- Building materials. 3.4 Advanced technology materials. 4.- Environmental and territorial engineering in basic industry. 4.1.-Valuation of environmental impacts. 4.2.- Restoration engineering in mining. 4.3.- Effluent and residue engineering. 4.4.- Environmental management and clean technologies 4.5.- Natural and technological risks

Scenario-Based Systems Engineering Application to Mine Warfare

Science.gov (United States)

2015-12-01

hunter- killer capabilities to find, classify, and destroy moored and bottom mines with sonar and video systems, cable cutting devices, and mine...Method: Serial 3 LCS MH-60s LCS: RMS with AN/AQS-20, MH-60s: Archerfish Hunt Method: Serial 1M MK18 MH-60s LCS: MK18 Mod 2, MH-60s...Archerfish Hunt Method: Serial 2M MK18 MH-60s LCS: MK18 Mod 2, MH-60s: Archerfish Hunt Method: Serial 3M MK18 MH-60s LCS: MK18

In-situ uranium mining: reservoir engineering aspects of leaching and restoration

International Nuclear Information System (INIS)

Kabir, M.I.

1982-01-01

To establish the feasibility of in-situ mining of uranium, a push-pull test of an in-situ uranium leaching process, which consists of a single injection/production test well and two observation wells, was designed to evaluate the parameters which govern the uranium production and restorability of a solution mined zone. The test procedure itself consists of injection (push cycle) of a preflush followed by lixiviant, a brief soak period (soak cycle), and subsequent production (pull cycle) into the same well. Based on computer modeling, procedures are defined which permit, for a properly designed test, the determination of both restoration and leaching parameters. The test procedure and design recommendations are also outlined. Two numerical simulators which model field scale uranium production and restoration operations are presented. These simulators are able to accommodate various well patterns and irregular reservoir boundaries, physical dispersion, directional permeability variations (if present), and a variety of injection/production strategies. A streamline-concentration balance technique has been used to develop the models. The assumption of time invariant boundary conditions and no transverse dispersion between the streamlines reduces the two dimensional problem to a bundle of one dimensional ones. It has been further shown that the production well effluent histories can easily be obtained by superposing the solution of the concentration balance equations for a single streamline, and thus reducing computation time significantly. Finally, the simulators have been used to study various reservoir engineering aspects to optimize in-situ uranium production from field scale operations

In-situ uranium mining: reservoir engineering aspects of leaching and restoration

Energy Technology Data Exchange (ETDEWEB)

Kabir, M.I.

1982-01-01

To establish the feasibility of in-situ mining of uranium, a push-pull test of an in-situ uranium leaching process, which consists of a single injection/production test well and two observation wells, was designed to evaluate the parameters which govern the uranium production and restorability of a solution mined zone. The test procedure itself consists of injection (push cycle) of a preflush followed by lixiviant, a brief soak period (soak cycle), and subsequent production (pull cycle) into the same well. Based on computer modeling, procedures are defined which permit, for a properly designed test, the determination of both restoration and leaching parameters. The test procedure and design recommendations are also outlined. Two numerical simulators which model field scale uranium production and restoration operations are presented. These simulators are able to accommodate various well patterns and irregular reservoir boundaries, physical dispersion, directional permeability variations (if present), and a variety of injection/production strategies. A streamline-concentration balance technique has been used to develop the models. The assumption of time invariant boundary conditions and no transverse dispersion between the streamlines reduces the two dimensional problem to a bundle of one dimensional ones. It has been further shown that the production well effluent histories can easily be obtained by superposing the solution of the concentration balance equations for a single streamline, and thus reducing computation time significantly. Finally, the simulators have been used to study various reservoir engineering aspects to optimize in-situ uranium production from field scale operations.

Application of CPM procedures in mine ventilation

International Nuclear Information System (INIS)

Wang, Y.J.; Mutmansky, J.M.

1982-01-01

Mine ventilation analysis is an engineering discipline that can be considered a branch of the body of science known as network analysis. Likewise, the group of engineering procedures known as the critical path method (CPM) is considered a branch of network analysis. It is therefore not surprising that mine ventilation network analysis and CPM have many similarities. These similarities are useful in analyzing several types of mine ventilation problems and will be utilized in this paper. The analogy between the free split in a ventilation circuit and the critical path in a scheduling network has been recognized by Owili-Eger (1973). While this was recognized as a property of a general ventilation network, many important applications to controlled-splitting problems also exist. The mathematical procedures necessary to apply CPM and network methods have previously been presented (Wang, 1981; Wang, 1982). This paper will illustrate the implementation of these methods by application to mine ventilation networks

Solution of problems, emerging with the transition to thin seams mining on underground mines

International Nuclear Information System (INIS)

Malkin, A.S.; Podshivalov, V.E.; Zhdamirov, V.M.; Kostarev, A.P.; Kulakov, A.N.; Savchenkov, V.E.

1997-01-01

The greatest volume of useful carbon-energetical and carbon-technological resources in the countries of the world consists of coal. Most likely, problems of the development of coal wining technology and coal consumption will interest scientists and mining engineers for a long time. Moreover, competing with the petroleum and gas industries becomes increasingly difficult. Considerable increases in coal production in countries with warm climates, and favourable mining and geological conditions also damages the international market for the coal industries of Russia (and Australia, India, and Vietnam). In a situation of critical deficits in both financial and material means in Russia, it is necessary to change the structure of the means of production and investment policies for the development of coal mining at every individual mine. 1 fig

Acid mine drainage

Science.gov (United States)

Bigham, Jerry M.; Cravotta, Charles A.

2016-01-01

Acid mine drainage (AMD) consists of metal-laden solutions produced by the oxidative dissolution of iron sulfide minerals exposed to air, moisture, and acidophilic microbes during the mining of coal and metal deposits. The pH of AMD is usually in the range of 2–6, but mine-impacted waters at circumneutral pH (5–8) are also common. Mine drainage usually contains elevated concentrations of sulfate, iron, aluminum, and other potentially toxic metals leached from rock that hydrolyze and coprecipitate to form rust-colored encrustations or sediments. When AMD is discharged into surface waters or groundwaters, degradation of water quality, injury to aquatic life, and corrosion or encrustation of engineered structures can occur for substantial distances. Prevention and remediation strategies should consider the biogeochemical complexity of the system, the longevity of AMD pollution, the predictive power of geochemical modeling, and the full range of available field technologies for problem mitigation.

Big data mining: In-database Oracle data mining over hadoop

Science.gov (United States)

Kovacheva, Zlatinka; Naydenova, Ina; Kaloyanova, Kalinka; Markov, Krasimir

2017-07-01

Big data challenges different aspects of storing, processing and managing data, as well as analyzing and using data for business purposes. Applying Data Mining methods over Big Data is another challenge because of huge data volumes, variety of information, and the dynamic of the sources. Different applications are made in this area, but their successful usage depends on understanding many specific parameters. In this paper we present several opportunities for using Data Mining techniques provided by the analytical engine of RDBMS Oracle over data stored in Hadoop Distributed File System (HDFS). Some experimental results are given and they are discussed.

Big Data and Nursing: Implications for the Future.

Science.gov (United States)

Topaz, Maxim; Pruinelli, Lisiane

2017-01-01

Big data is becoming increasingly more prevalent and it affects the way nurses learn, practice, conduct research and develop policy. The discipline of nursing needs to maximize the benefits of big data to advance the vision of promoting human health and wellbeing. However, current practicing nurses, educators and nurse scientists often lack the required skills and competencies necessary for meaningful use of big data. Some of the key skills for further development include the ability to mine narrative and structured data for new care or outcome patterns, effective data visualization techniques, and further integration of nursing sensitive data into artificial intelligence systems for better clinical decision support. We provide growth-path vision recommendations for big data competencies for practicing nurses, nurse educators, researchers, and policy makers to help prepare the next generation of nurses and improve patient outcomes trough better quality connected health.

Coal mine subsidence and structures

International Nuclear Information System (INIS)

Gray, R.E.

1988-01-01

Underground coal mining has occurred beneath 32 x 10 9 m 2 (8 million acres) of land in the United States and will eventually extend beneath 162 x 10 9 m 2 (40 million acres). Most of this mining has taken place and will take place in the eastern half of the United States. In areas of abandoned mines where total extraction was not achieved, roof collapse, crushing of coal pillars, or punching of coal pillars into softer mine floor or roof rock is now resulting in sinkhole or trough subsidence tens or even hundreds of years after mining. Difference in geology, in mining, and building construction practice between Europe and the United States preclude direct transfer of European subsidence engineering experience. Building damage cannot be related simply to tensile and compressive strains at the ground surface. Recognition of the subsidence damage role played by ground-structure interaction and by structural details is needed

Cost of mining Eastern coal

International Nuclear Information System (INIS)

Anon.

1990-01-01

This paper, Chapter 7.2.3 of the 'surface mining' reference book, gives an example of how the cost of mining a ton of coal is calculated. Conditions set down are for a coal tract of 50.6 ha in West Virginia, USA to be mined by the contour surface method, the seam being 101.6cm thick. Elements of the costing are: permitting and bonding costs, engineering and construction costs, equipment and other operating expenses (such as hauling and wheeling), royalties, direct taxes and fees, costs of revegetation, and employment costs (payroll and medical expenses). 5 tabs

Measures to restore metallurgical mine wasteland using ecological restoration technologies: A case study at Longnan Rare Earth Mine

Science.gov (United States)

Rao, Yunzhang; Gu, Ruizhi; Guo, Ruikai; Zhang, Xueyan

2017-01-01

Whereas mining activities produce the raw materials that are crucial to economic growth, such activities leave extensive scarring on the land, contributing to the waste of valuable land resources and upsetting the ecological environment. The aim of this study is therefore to investigate various ecological technologies to restore metallurgical mine wastelands. These technologies include measures such as soil amelioration, vegetation restoration, different vegetation planting patterns, and engineering technologies. The Longnan Rare Earth Mine in the Jiangxi Province of China is used as the case study. The ecological restoration process provides a favourable reference for the restoration of a metallurgical mine wasteland.

Proceedings of the 15. annual national meeting of the American Society for Surface Mining and Reclamation. Mining -- Gateway to the future

International Nuclear Information System (INIS)

Throgmorton, D.; Nawrot, J.; Mead, J.; Galetovic, J.; Joseph, W.

1998-01-01

The 124 papers of these proceedings are arranged under the following topical sections: Minerals education; Hydrology--Characterization and monitoring; Tailings--Reclamation; Reforestation; Mine drainage--Biogeochemical processes; Mine drainage--Treatment, general; Mine drainage--Passive treatment, wetlands; Mine drainage--Prediction and monitoring; Acid soils--Reclamation practices; Wildlife and fisheries habitat; Subsidence--Engineering practices and environmental effects; OSM acid forming materials mini workshops; RUSLE--Erosion prediction techniques on mined construction and reclaimed lands; IDNR wetlands technology transfer program; Mine planning and postmining land use; Vegetation establishment--Principles and practices; Vegetation establishment--Warm season grasses; Coal combustion by-products--General; Coal combustion by-products--Mine drainage treatment; and Prime farmland reclamation and mine soils management. Papers within scope have been processed separately for inclusion on the data base

Improve Data Mining and Knowledge Discovery through the use of MatLab

Science.gov (United States)

Shaykahian, Gholan Ali; Martin, Dawn Elliott; Beil, Robert

2011-01-01

Data mining is widely used to mine business, engineering, and scientific data. Data mining uses pattern based queries, searches, or other analyses of one or more electronic databases/datasets in order to discover or locate a predictive pattern or anomaly indicative of system failure, criminal or terrorist activity, etc. There are various algorithms, techniques and methods used to mine data; including neural networks, genetic algorithms, decision trees, nearest neighbor method, rule induction association analysis, slice and dice, segmentation, and clustering. These algorithms, techniques and methods used to detect patterns in a dataset, have been used in the development of numerous open source and commercially available products and technology for data mining. Data mining is best realized when latent information in a large quantity of data stored is discovered. No one technique solves all data mining problems; challenges are to select algorithms or methods appropriate to strengthen data/text mining and trending within given datasets. In recent years, throughout industry, academia and government agencies, thousands of data systems have been designed and tailored to serve specific engineering and business needs. Many of these systems use databases with relational algebra and structured query language to categorize and retrieve data. In these systems, data analyses are limited and require prior explicit knowledge of metadata and database relations; lacking exploratory data mining and discoveries of latent information. This presentation introduces MatLab(TradeMark)(MATrix LABoratory), an engineering and scientific data analyses tool to perform data mining. MatLab was originally intended to perform purely numerical calculations (a glorified calculator). Now, in addition to having hundreds of mathematical functions, it is a programming language with hundreds built in standard functions and numerous available toolboxes. MatLab's ease of data processing, visualization and

Geo-science aims of underground exploration of the Gorleben salt mine

International Nuclear Information System (INIS)

Langer, M.; Venzlaff, H.

1987-01-01

The measures taken are explained separately, according to the technical areas geology/petrography - geophysics - engineering geology/geotechnology - geo-chemistry. The results of the underground exploration are used directly to produce documents for the planning process, securing proof and the final storage planning (specific site mine dimensions, analysis of accidents, storage strategies). After completion of underground exploration, geoscience information on the suitability of the salt mine at Gorleben will be available in connection with a storage concept agreed between the geo-technologists and the mining engineers. (orig.) [de

Simulation Engine for Fluid Solid Interaction Problems and its Application to the Modelling of Air Blast Hazards in Block Cave Mining.

Science.gov (United States)

Galindo Torres, S. A.; Scheuermann, A.; Ruest, M.

2016-12-01

Air blasts that may occur in a block caving mining operation represent a significant hazard for personnel as well as to mining infrastructure. Uncontrolled caving of a large volume of broken rock into a mine void causes compression of the air within, forcing it to flow at high velocities into connecting tunnels such as extraction points beneath the cave or observation points intersecting the cave. This high velocity flow of air can cause injury to personnel and significant damage to equipment. In this presentation, we introduce a simulation engine for the air blast problem. The solid material is modelled using the Discrete Element Method (DEM) and the fluid (air) is modelled using the Lattice Boltzmann Method (LBM). The combined DEM-LBM approach has been introduced by our group at the University of Queensland[1]. LBM allows us to introduce an appropriate equation of state for the air that simulates compressibility as a function of the speed of sound. Validation examples are presented to justify the use of this tool for an air blasting situation. A section view of one simulation is provided in Fig 1. An investigation into the risk of developing air pockets as a function of fragment size distribution is also conducted and described. The fragment size distribution can be assessed during mining and the risk of air pockets forming (and consequently of air blast occurring) can be deduced and mitigation measures put in place. The effect of other key variables that can be determined from geotechnical investigations, such as fracture frequency, are also systematically explored. It is expected that the results of this study can elucidate key features of the air blasting phenomenon in order to formulate safer mining protocols. references 1. Galindo-Torres, S.A., A coupled Discrete Element Lattice Boltzmann Method for the simulation of fluid-solid interaction with particles of general shapes. Computer Methods in Applied Mechanics and Engineering, 2013. 265(0): p. 107-119.

Acclimatization Services to the Mining Industry: Statistics for 1990

CSIR Research Space (South Africa)

Hitge, JJ

1991-10-01

Full Text Available This report is designed to convey information to mine management, environmental engineers, training personnel and acclimatization supervisors that will allow an appraisal of their mine's position with regard to heat acclimatization of workers...

CSIR Division of Mining Technology annual review 1993/94

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

The Division of Mining Technology of the CSIR (Council for Scientific and Industrial Research) works in partnership with the mining industry to solve problems threatening the health, safety and well-being of the workforce, and the productivity of mining operations through the development and implementation of knowledge and technology. The annual review describes the Division's research projects in the following field: rock engineering (for gold, platinum and coal mining); mining environment; occupational hygiene; surface environment; and mining equipment and systems (systems and equipment, orebody information, coal mining and causes of accidents). Details are also given of the Division's publications, research and consultancy services and information centre.

Present and future mine effluents management at Zirovski Vrh uranium mine

International Nuclear Information System (INIS)

Logar, Z.; Likar, B.; Gantar, I.

2002-01-01

Zirovski Vrh uranium mine and its facilities are situated on the northeastern slopes of the Zirovski Vrh ridge (960 m) and on the southern slopes of Crna gora (611 m) respectively. Mine elevation is from 430 m (bottom of the valley) to 580 m (P-1 adit). All effluents from the mine and mill objects flow into the Brebovscica river (with average yearly flow of 0.74 m 3 /s): run off mine water; mine waste pile Jazbec outflow; mill tailings Borst outflows; effluents from mine temporary mine waste piles P-1, P-9, P-36 are of minor significance. The first three effluents and the recipient surface water flows (the Todrascica brook and the Brebovscica river) are monitored extensively. The impact of radioactive polluted outflows on named waters is proved, but far under the maximal permitted limit values. The authorised maximal limits values for mine effluents were obtained in 1996. Detail design will ensure that this values will not be exceeded in the future. The long term planes are to minimise the uranium concentrations in the run off mine water by target underground drilling. The mine waste pile and the mill tailings will be covered by engineered cover system to avoid clean water contamination by weathering and ablution as well. The existing effluents from the mill tailings will diminish after the remediation and consolidation of the tailing. The Government of Slovenia funds the remediation of the uranium production site Zirovski Vrh. Estimated needed funds for remediation of the main objects are shown in the table below. The total investment includes also the costs for effluents control. Area Mio US$ Underground mine remediation 19.00 Mine waste pile remediation 6.50 Mill tailings remediation 2.24 Total investment costs 27.74 Above figures do not include operation costs of the Zirovski Vrh Mine, approximately US$ 2.2 Mio per year nowadays. The last implementation schedule foresights the end of remediation works in year 2005. After that starts trial monitoring of 5 years

The environmental context of Acidithiobacillus ferrooxidans and its potential role as an ecosystem engineer in sulphidic mine waste

Energy Technology Data Exchange (ETDEWEB)

Ebenaa, Gustav

2001-06-01

Microorganisms are the causative agent of the environmental problems since they catalyse the weathering of the (sulphidic) waste. The chemical oxidation alone is not fast enough to create any severe environmental problems. Acidithiobacillus ferrooxidans is thought to be a key organism in weathering of sulphide minerals. A. ferrooxidans is affected by several more or less abiotic factors. The influence of temperature, pH and nutrient deficiency as potentially limiting factors for the activity of A. ferrooxidans has been investigated. It seems that temperature has less influence on its activity, but rather reflects the origin of the bacterial isolate. An alkaline pH seems enough to hinder growth and activity. The nutrients do not seem to be a limiting factor in the studied environment. The possible regulation of the activity of A. ferrooxidans is therefore a way to, at least partly, mitigate the environmental impact from mine waste. Waste from the mining industry is the largest waste problem in Sweden. With amounts over 600 million tonnes one could easily imagine the tremendous cost involved in the abatement. The MiMi-programme, with researchers from several relevant fields, has as its aim to evaluate present and to find alternative techniques to mitigate the environmental impact from mine waste. The understanding of A. ferrooxidans and its role as an ecosystem engineer is essential both in evaluating present techniques and even more so in finding alternative abatement techniques for sulphidic mine waste.

Occupational radiation safety in mining

International Nuclear Information System (INIS)

Stocker, H.

1985-01-01

The first International Conference on Occupational Radiation Safety in Mining was held three years ago in Golden, Colorado, U.S.A., and it provided an excellent forum for an exchange of information on the many scientific, technical and operational aspects of radiation safety in mining. I am aware of the broad spectrum of epidemiological, engineering and related studies which have been pursued during the past three years with a view to achieving further improvements in radiation protection and I expect that the information on these studies will contribute significantly to a wider understanding of subject, and in particular, the means by which radiation safety measures in mining can be optimized

Data mining methods

CERN Document Server

Chattamvelli, Rajan

2015-01-01

DATA MINING METHODS, Second Edition discusses both theoretical foundation and practical applications of datamining in a web field including banking, e-commerce, medicine, engineering and management. This book starts byintroducing data and information, basic data type, data category and applications of data mining. The second chapterbriefly reviews data visualization technology and importance in data mining. Fundamentals of probability and statisticsare discussed in chapter 3, and novel algorithm for sample covariants are derived. The next two chapters give an indepthand useful discussion of data warehousing and OLAP. Decision trees are clearly explained and a new tabularmethod for decision tree building is discussed. The chapter on association rules discusses popular algorithms andcompares various algorithms in summary table form. An interesting application of genetic algorithm is introduced inthe next chapter. Foundations of neural networks are built from scratch and the back propagation algorithm is derived...

Abstracts of the International Conference on Occupational Radiation Safety in Mining

International Nuclear Information System (INIS)

1984-01-01

Abstracts are provided for the 89 papers presented at this conference. They cover the areas of mine ventilation and engineering, instrumentation, dosimetry, and epidemiology, particularly in uranium mines

Influence of Engineering Bacteria Quantitative Inspection on Diversity of Anpeng Alkali Mine Resources Exploitation

Directory of Open Access Journals (Sweden)

Yu Tao

2016-03-01

Full Text Available Cadmium (Cd is a heavy metal pollutant seriously threatening creatures, and highly concentrated Cd in soil severely inhibits the activity of microbial populations. Soil in Anpeng Alkali Mine area in Nanyang city (Henan province is seriously polluted by heavy metal. Both copper (Cu and Cd content are found to be over standard, in which, Cu belongs to mild contamination while Cd is a serious contamination. To detect diversity of microbial communities in soil in the process of bioremediation, Cd polluted soil samples are collected from orefield for pot experiment, Biolog micro-plate technology is used to study the influence of applying low, medium and high amount of rice straw (5.3 t/ha, 10.2 t/ha and 23.4 t/ha in polluted soil and combining low, medium and high amount of rice straw with surface displayed engineering bacteria (X4/pCIM on microbial community. In the meantime, X4/pCIM is quantitatively measured by real-time polymerase chain reaction (PCR. Biolog experimental results indicate that the combination of rice straw and engineering bacteria is able to change the composition of soil microbial community, and has a difference in influencing rhizosphere and non-rhizosphere microorganisms. Through real-time PCR, it is found that the number of engineering bacteria falls to 103 after 120 days of bioremediation. Therefore, it can be concluded that combining rice straw with engineering bacteria can change the composition of soil microbial community and have diverse influences as application rate changes, without obvious rules to follow.

Antimicrobials of Bacillus species: mining and engineering

NARCIS (Netherlands)

Zhao, Xin

2016-01-01

Bacillus sp. have been successfully used to suppress various bacterial and fungal pathogens. Due to the wide availability of whole genome sequence data and the development of genome mining tools, novel antimicrobials are being discovered and updated,;not only bacteriocins, but also NRPs and PKs. A

Supporting of mine workings and design of support systems. Madenlerde tahkimat isleri ve tasarmi

Energy Technology Data Exchange (ETDEWEB)

Biron, C; Arioglu, E; (Istanbul Teknik Universitesi, Maden Fakultesi)

1980-01-01

This article deals with elements of elasticity in rocks and examines the engineering properties of rocks. It includes stress distributions around mine openings and deformations of mine openings. Strata control concept in coal mining is explained. Support systems in stone drifts, gateways, shafts and longwalls are discussed; timber supports, steel arches, articulated arches, roof bolting, concrete supports, supports on mechanized faces are detailed. Emphasis is placed upon engineering properties of materials of support systems. The design concepts of mine support systems are described. The objects of the design are expressed with several numerical examples. It concludes with stowing: pneumatic stowing, and hydraulic stowing in metal and coal mining.

Understanding nursing units with data and theory.

Science.gov (United States)

Diers, Donna; Hendrickson, Karrie; Rimar, Joan; Donovan, Donna

2013-01-01

Nursing units are social systems whose function depends on many variables. Available nursing data, combined with a theory of organizational diagnosis, can be used to understand nursing unit performance. One troubled unit served as a case study in organizational diagnosis and treatment using modern methods of data mining and performance improvement. Systems theory did not prescribe how to fix an underbounded system. The theory did suggest, however, that addressing the characteristics of overbounded and underbounded systems can provide some order and structure and identify helpful resources. In this instance, the data analysis served to help define the unit's problems in conjunction with information gained from talking with the nurses and touring the unit, but it was the theory that gave hints for direction for change.

Arguments for the need of mining education continuity and development in Romania

Science.gov (United States)

Bud, I.; Duma, S.; Pasca, I.; Gusat, D.

2018-01-01

Mining is considered the oldest conscious man activity. In the beginning, man searched for hard rocks in the outskirts area and used it to make weapons and ornaments. Subsequently, civilizations evolved through the development of infrastructure, buildings and monuments and finally, weapons. For all these it was necessary to have mineral raw materials obtained under increasingly difficult conditions, through increasingly evolved techniques. In this way, the art of mining and metallurgy was born, which led to the formation of scientific bases. The mining activity was equally art and science. The art and the science have been learned and taught in schools since ancient times and continue today in large universities with mining engineering, metallurgy, mining topography, mining environmental protection, and geology. Lately, in Romania, the mining high school has reached a deadlock and the middle and professional school has collapsed. The development of infrastructure, construction, etc. requires the exploitation and valorisation of mineral resources based on specialists. The paper warns against the danger of losing tradition and skills in mining engineers formation and militate for the re-establishment of professional and technical schools.

ANFO bulk loading in coal mines

Energy Technology Data Exchange (ETDEWEB)

Gajjar, A.

1987-08-01

With India's total coal production projected to increase from 152 to 237 million tons by 1990, net additional production from new mines must be more because of substantial depletion in existing mines. This article discusses the best possible application of explosive techniques in open-cast coal mines to economize production cost. The most energy-efficient and safest explosive is ANFO (ammonium nitrate, fuel oil); however, manual charging by INFO is not possible. Therefore, the solution is the application of bulk-loading systems of ANFO for giant mining operations. Cost of blasting per ton of coal production in India is in the range of Rs 25. Thus, the author suggests it will be the responsibility of mining engineers to see that the ANFO based bulk-loading system is implemented and the cost of production per ton reduced to Rs 19.50.

Inductive learning as a fusion engine for mine detection

Energy Technology Data Exchange (ETDEWEB)

Kercel, S.W.; Dress, W.B.

1997-08-01

Semiotics is defined by some researchers as {open_quotes}the study of the appearance (visual or otherwise) meaning, and use of symbols and symbol systems.{close_quotes} Semiotic fusion of data from multiple sensory sources is a potential solution to the problem of landmine detection. This turns out to be significant, because notwithstanding the diversity of sensor technologies being used to attack the problem, there is no single effective landmine sensor technology. The only practical, general-purpose mine detector presently available is the trained dog. Most research into mine-detection technology seeds to emulate the dog`s seemingly uncanny abilities. An ideal data-fusion system would mimic animal reaction, with the brain`s perceptive power melding multiple sensory cues into an awareness of the size and location of a mine. Furthermore, the fusion process should be adaptive, with the skill at combining cues into awareness improving with experience. Electronic data-fusion systems reported in the countermine literature use conventional vector-based pattern recognition methods. Although neural nets are popular, they have never satisfactorily met the challenge. Despite years of investigation, nobody has ever found a vector space representation that reliably characterizes mine identity. This strongly suggests that the features have not been found because researchers have been looking for the wrong characteristics. It is worth considering that dogs probably do not represent data as mathematical number lists, but they almost certainly represent data via semiotic structures.

120 Years of Education for Mine Surveyors in South Africa A ...

African Journals Online (AJOL)

Grobler, Hennie

war, political changes and changes in the mining industry during this period. This paper provides a short history of the development of the three institutions involved with undergraduate teaching in the field of mining engineering and Mine Surveying. The paper continues to outline the progression of education models in the ...

Surface mining machines problems of maintenance and modernization

CERN Document Server

Rusiński, Eugeniusz; Moczko, Przemysław; Pietrusiak, Damian

2017-01-01

This unique volume imparts practical information on the operation, maintenance, and modernization of heavy performance machines such as lignite mine machines, bucket wheel excavators, and spreaders. Problems of large scale machines (mega machines) are highly specific and not well recognized in the common mechanical engineering environment. Prof. Rusiński and his co-authors identify solutions that increase the durability of these machines as well as discuss methods of failure analysis and technical condition assessment procedures. "Surface Mining Machines: Problems in Maintenance and Modernization" stands as a much-needed guidebook for engineers facing the particular challenges of heavy performance machines and offers a distinct and interesting demonstration of scale-up issues for researchers and scientists from across the fields of machine design and mechanical engineering.

Numerical modelling of mine workings.

CSIR Research Space (South Africa)

Lightfoot, N

1999-03-01

Full Text Available to cover most of what is required for a practising rock mechanics engineer to be able to use any of these five programs to solve practical mining problems. The chapters on specific programs discuss their individual strengths and weaknesses and highlight... and applications of numerical modelling in the context of the South African gold and platinum mining industries. This includes an example that utilises a number of different numerical 3 modelling programs to solve a single problem. This particular example...

Control of radon daughters in underground mining

International Nuclear Information System (INIS)

Swent, L.W.

1983-01-01

This paper discusses technical developments that may enable uranium mine operators to improve engineering controls of radon daughter concentrations in mines, and developments in regulatory controls. The origin of radon daughters in underground mines is explained. The procedure for sampling and determining the concentration of alpha radiation in sampled air is reviewed. The principal technical development in the last few years has been the perfection and use of a class of meters which determine radon daughter concentrations in an air sample in a matter of two or three minutes without any aging period. A number of underground uranium mine operators are now using ''instant'' type meters and the Mine Safety and Health Administration (MSHA) has approved their use in a number of mines. The difficulty experienced by uranium mine operators in complying with a MSHA regulation which requires that no person be exposed to radon daughter concentrations exceeding 1 Working Level (WL) in any active working place is discussed

120 years of education for mine surveyors in South Africa: A ...

African Journals Online (AJOL)

The profession has seen a number of changes brought about by war, political changes and changes in the mining industry during this period. This paper provides a short history of the development of the three institutions involved with undergraduate teaching in the field of mining engineering and Mine Surveying. The paper ...

School Nurse Workload.

Science.gov (United States)

Endsley, Patricia

2017-02-01

The purpose of this scoping review was to survey the most recent (5 years) acute care, community health, and mental health nursing workload literature to understand themes and research avenues that may be applicable to school nursing workload research. The search for empirical and nonempirical literature was conducted using search engines such as Google Scholar, PubMed, CINAHL, and Medline. Twenty-nine empirical studies and nine nonempirical articles were selected for inclusion. Themes that emerged consistent with school nurse practice include patient classification systems, environmental factors, assistive personnel, missed nursing care, and nurse satisfaction. School nursing is a public health discipline and population studies are an inherent research priority but may overlook workload variables at the clinical level. School nurses need a consistent method of population assessment, as well as evaluation of appropriate use of assistive personnel and school environment factors. Assessment of tasks not directly related to student care and professional development must also be considered in total workload.

Diversification of the Higher Mining Education Financing in Globalization Era

Science.gov (United States)

Frolova, Victoria; Dolina, Olga; Shpil'kina, Tatyana

2017-11-01

In the current conditions of global competition, the development of new mining technologies, the requirements to labor resources, their skills and creative potential are increasing. The tasks facing the mining industry cannot be solved without highly qualified personnel, especially managers, engineers and technicians, specialists who possess the knowledge and competences necessary for the development of science and technology of mining, and ensuring mining industrial safety. The authors analyze personnel problems and financing of mining higher education, conclude that there is a need to develop social partnership and diversify the sources of funding for training, advanced training and retraining of personnel for mining and processing of solid mineral deposits.

Diversification of the Higher Mining Education Financing in Globalization Era

Directory of Open Access Journals (Sweden)

Frolova Victoria

2017-01-01

Full Text Available In the current conditions of global competition, the development of new mining technologies, the requirements to labor resources, their skills and creative potential are increasing. The tasks facing the mining industry cannot be solved without highly qualified personnel, especially managers, engineers and technicians, specialists who possess the knowledge and competences necessary for the development of science and technology of mining, and ensuring mining industrial safety. The authors analyze personnel problems and financing of mining higher education, conclude that there is a need to develop social partnership and diversify the sources of funding for training, advanced training and retraining of personnel for mining and processing of solid mineral deposits.

Environmental and ventilation benefits for underground mining operations using fuel cell powered production equipment

International Nuclear Information System (INIS)

Kocsis, C.; Hardcastle, S.

2007-01-01

The benefits of replacing diesel engines with fuel cells in mine production equipment were discussed. The paper was part of a multi-year feasibility study conducted to evaluate the use of hydrogen fuel cell-powered equipment to replace diesel engine powered equipment in underground mining operations. The feasibility study demonstrated that fuel cells are capable of eliminating the unwanted by-products of combustion engines. However, the use of fuel cells also reduced the amount of ventilation that mines needed to supply, thereby further reducing energy consumption. This study examined the benefits of replacing diesel engines with fuel cells, and discussed the mitigating qualifiers that may limit ventilation energy savings. Solutions to retaining and maintaining additional ventilation in the event of hydrogen leaks from fuel cell stacks were also investigated. The analyses were conducted on 6 operating mines. Current operating costs were compared with future operating conditions using fuel cell powered production vehicles. Operating costs of the primary ventilation system were established with a mine ventilation simulator. The analysis considered exhaust shaft velocities, heating system air velocities, and levels of silica exposure. Canadian mine design criteria were reviewed. It was concluded that appropriate safeguards are needed along hydrogen distribution lines to lower the impacts of hydrogen leaks. Large financial commitments may also be required to ensure a spark-free environment. 20 refs., 6 tabs., 3 figs

Geotechnical Characterization of Mined Clay from Appalachian Ohio: Challenges and Implications for the Clay Mining Industry

Science.gov (United States)

Moran, Anthony R.; Hettiarachchi, Hiroshan

2011-01-01

Clayey soil found in coal mines in Appalachian Ohio is often sold to landfills for constructing Recompacted Soil Liners (RSL) in landfills. Since clayey soils possess low hydraulic conductivity, the suitability of mined clay for RSL in Ohio is first assessed by determining its clay content. When soil samples are tested in a laboratory, the same engineering properties are typically expected for the soils originated from the same source, provided that the testing techniques applied are standard, but mined clay from Appalachian Ohio has shown drastic differences in particle size distribution depending on the sampling and/or laboratory processing methods. Sometimes more than a 10 percent decrease in the clay content is observed in the samples collected at the stockpiles, compared to those collected through reverse circulation drilling. This discrepancy poses a challenge to geotechnical engineers who work on the prequalification process of RSL material as it can result in misleading estimates of the hydraulic conductivity of the samples. This paper describes a laboratory investigation conducted on mined clay from Appalachian Ohio to determine how and why the standard sampling and/or processing methods can affect the grain-size distributions. The variation in the clay content was determined to be due to heavy concentrations of shale fragments in the clayey soils. It was also concluded that, in order to obtain reliable grain size distributions from the samples collected at a stockpile of mined clay, the material needs to be processed using a soil grinder. Otherwise, the samples should be collected through drilling. PMID:21845150

Geotechnical characterization of mined clay from Appalachian Ohio: challenges and implications for the clay mining industry.

Science.gov (United States)

Moran, Anthony R; Hettiarachchi, Hiroshan

2011-07-01

Clayey soil found in coal mines in Appalachian Ohio is often sold to landfills for constructing Recompacted Soil Liners (RSL) in landfills. Since clayey soils possess low hydraulic conductivity, the suitability of mined clay for RSL in Ohio is first assessed by determining its clay content. When soil samples are tested in a laboratory, the same engineering properties are typically expected for the soils originated from the same source, provided that the testing techniques applied are standard, but mined clay from Appalachian Ohio has shown drastic differences in particle size distribution depending on the sampling and/or laboratory processing methods. Sometimes more than a 10 percent decrease in the clay content is observed in the samples collected at the stockpiles, compared to those collected through reverse circulation drilling. This discrepancy poses a challenge to geotechnical engineers who work on the prequalification process of RSL material as it can result in misleading estimates of the hydraulic conductivity of the samples. This paper describes a laboratory investigation conducted on mined clay from Appalachian Ohio to determine how and why the standard sampling and/or processing methods can affect the grain-size distributions. The variation in the clay content was determined to be due to heavy concentrations of shale fragments in the clayey soils. It was also concluded that, in order to obtain reliable grain size distributions from the samples collected at a stockpile of mined clay, the material needs to be processed using a soil grinder. Otherwise, the samples should be collected through drilling.

Geotechnical Characterization of Mined Clay from Appalachian Ohio: Challenges and Implications for the Clay Mining Industry

Directory of Open Access Journals (Sweden)

Anthony R. Moran

2011-06-01

Full Text Available Clayey soil found in coal mines in Appalachian Ohio is often sold to landfills for constructing Recompacted Soil Liners (RSL in landfills. Since clayey soils possess low hydraulic conductivity, the suitability of mined clay for RSL in Ohio is first assessed by determining its clay content. When soil samples are tested in a laboratory, the same engineering properties are typically expected for the soils originated from the same source, provided that the testing techniques applied are standard, but mined clay from Appalachian Ohio has shown drastic differences in particle size distribution depending on the sampling and/or laboratory processing methods. Sometimes more than a 10 percent decrease in the clay content is observed in the samples collected at the stockpiles, compared to those collected through reverse circulation drilling. This discrepancy poses a challenge to geotechnical engineers who work on the prequalification process of RSL material as it can result in misleading estimates of the hydraulic conductivity of the samples. This paper describes a laboratory investigation conducted on mined clay from Appalachian Ohio to determine how and why the standard sampling and/or processing methods can affect the grain-size distributions. The variation in the clay content was determined to be due to heavy concentrations of shale fragments in the clayey soils. It was also concluded that, in order to obtain reliable grain size distributions from the samples collected at a stockpile of mined clay, the material needs to be processed using a soil grinder. Otherwise, the samples should be collected through drilling.

Health in mines

Energy Technology Data Exchange (ETDEWEB)

Breuer, H

1978-01-01

This report summarizes the information gained from research carried out under the five-year programme (1971-1976) relating to health in mines. This programme concentrates on technical means of dust control, and the various aspects of this topic are reviewed. The purpose of the epidemiology of pneumoconiosis is to determine the origin and development of this endemic disease with a view to formulating a policy of worker protection. The constituents of dust and their possible influences are studied. Measuring and determining the characteristics of dusts are the subject of the second group of research projects. Prevention techniques have been proposed, tried out and developed, thus providing the mining industry with a set of dust control methods. water infusion, dedusting on coal-getting and heading machines, control of dust produced by caving, etc. A chapter devoted to iron ore mines discusses means of protection against noxious emissions from Diesel engines and explosives. (Editions available in English, in German, in French, in Italian, and in Dutch)

Integration of Web mining and web crawler: Relevance and State of Art

OpenAIRE

Subhendu kumar pani; Deepak Mohapatra,; Bikram Keshari Ratha

2010-01-01

This study presents the role of web crawler in web mining environment. As the growth of the World Wide Web exceeded all expectations,the research on Web mining is growing more and more.web mining research topic which combines two of the activated research areas: Data Mining and World Wide Web .So, the World Wide Web is a very advanced area for data mining research. Search engines that are based on web crawling framework also used in web mining to find theinteracted web pages. This paper discu...

Guidelines for the integrated planning and design of underground coal mines.

CSIR Research Space (South Africa)

Fourie, GA

2001-11-01

Full Text Available Mine planning and design involves the compilation and integration of all relevant geological, geotechnical, mining, engineering and economic data into a single document to define and describe the exploitation strategy for a particular mineral...

Figure mining for biomedical research.

Science.gov (United States)

Rodriguez-Esteban, Raul; Iossifov, Ivan

2009-08-15

Figures from biomedical articles contain valuable information difficult to reach without specialized tools. Currently, there is no search engine that can retrieve specific figure types. This study describes a retrieval method that takes advantage of principles in image understanding, text mining and optical character recognition (OCR) to retrieve figure types defined conceptually. A search engine was developed to retrieve tables and figure types to aid computational and experimental research. http://iossifovlab.cshl.edu/figurome/.

Design guidelines for multi-seam mining at Elliot Lake

International Nuclear Information System (INIS)

Hedley, D.G.F.

1978-04-01

With the current expansion in uranium mining, multi-seam mining could again be practised at Elliot Lake as it was in the 1960s. Information on the dimensions of stopes, pillars, and parting zone was gathered from plans and sections of the relevant closed mines. Discussions were held with personnel familiar with these mines to establish instances of pillar, roof, and parting zone failures. Design guidelines are formulated for stope and pillar dimensions in multi-seam mining for a range of orebody configurations using past practice in a back-analysis approach. Constraints imposed by dip and seam thickness on the choice of equipment and mining layout are evaluated. An attempt is made to bring together the engineering aspects, including rock mechanics, of multi-seam mine design with uranium recovery and other economic factors for three alternative mine layouts: single-seam mining, double-seam mining, and seams-and-parting mining. A series of examples are worked through, showing how the design guidelines can be applied for typical orebody configurations

Lunabotics Mining Competition

Science.gov (United States)

Mueller, Rob; Murphy, Gloria

2010-01-01

This slide presentation describes a competition to design a lunar robot (lunabot) that can be controlled either remotely or autonomously, isolated from the operator, and is designed to mine a lunar aggregate simulant. The competition is part of a systems engineering curriculum. The 2010 competition winners in five areas of the competition were acknowledged, and the 2011 competition was announced.

Fiscal 1998 engineer interchange project on the engineer interchange project (coal mine technology field), international interchange project. Preliminary study in Russia; 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Jizen chosa (Russia)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the engineer interchange project (coal mine technology field), field survey for collecting information was made on the level and trend of production technology through visits to some coal industry organizations by specialists in Russia which is one candidate for the engineer training project by sending and receiving. Although coal is positioned as an important energy resource in Russia, poor business performance and a decrease in production are reported because of privatization and cur off of subsidies during a transfer period to a market economy. In addition, severe environment surrounding the Russian coal industry such as a delay of facility renewal due to poor funds, overage facilities, and moral reduction of workers due to a rationing delay has a potential for further reduction of production. The research group thus surveyed the current state of the Russian coal industry such as actual production structures, actual coal mines, technical levels, and various problem points in Moscow and Baykal districts. (NEDO)

State Mines Inspectorate of Saarland and Rheinland-Pfalz, Mines InspectorateSaarbruecken/ Mines Inspectorate Rheinland-Pfalz. Annual report 2000. Economic and technical aspects, industrial safety and enviromental protection, statistics, activities of the mining authorities; Oberbergamt fuer das Saarland und das Land Rheinland-Pfalz, Bergamt Saarbruecken/Bergamt Rheinland-Pfalz. Jahresbericht 2000. Bergwirtschaft, Bergtechnik, Arbeitsschutz, Umweltschutz, Statistiken, Taetigkeiten der Bergbehoerden

Energy Technology Data Exchange (ETDEWEB)

Boettcher, R.; Hugo, K.H.; Kuhn, M.; Strauch, T. (comps.)

2001-07-01

The annual report of the Saarland and Rheinland-Pfalz State Mines Inspectorate and the Mines Inspectorates of the two states provide an insight into the many activities of mines inspectorates and of the current trends in mining engineering. The importance of mining and regional raw materials management is stressed. [German] Der vorliegende Jahresbericht des Oberbergamtes fuer das Saarland und das Land Rheinland-Pfalz sowie der Bergaemter in beiden Bundeslaendern gibt einen Einblick in das vielfaeltige Arbeitsgebiet der Bergbehoerden. Gleichzeitig vermittelt er einen Ueberblick ueber die bergtechnische Entwicklung und unterstreicht die volkswirtschaftliche Bedeutung des Bergbaus und der standortgebundenen Rohstoffwirtschaft. (orig.)

State Mines Inspectorate of Saarland and Rheinland-Pfalz, Mines Inspectorate Saarbruecken / Mines Inspectorate Rheinland-Pfalz. Annual report 2001. Economic and technical aspects, industrial safety and environmental protection, statistics, activities of the mining authorities; Oberbergamt fuer das Saarland und das Land Rheinland-Pfalz, Bergamt Saarbruecken / Bergamt Rheinland-Pfalz. Jahresbericht 2001. Bergwirtschaft, Bergtechnik, Arbeitsschutz, Umweltschutz, Statistiken, Taetigkeiten der Bergbehoerden

Energy Technology Data Exchange (ETDEWEB)

Boettcher, R.; Hugo, K.H.; Kuhn, M.; Strauch, T. (comps.)

2002-07-01

The annual report of the Saarland and Rheinland-Pfalz State Mines Inspectorate and the Mines Inspectorates of the two states provide an insight into the many activities of mines inspectorates and of the current trends in mining engineering. The importance of mining and regional raw materials management is stressed. [German] Der vorliegende Jahresbericht des Oberbergamtes fuer das Saarland und das Land Rheinland-Pfalz sowie der Bergaemter in beiden Bundeslaendern gibt einen Einblick in das vielfaeltige Arbeitsgebiet der Bergbehoerden. Gleichzeitig vermittelt er einen Ueberblick ueber die bergtechnische Entwicklung und unterstreicht die volkswirtschaftliche Bedeutung des Bergbaus und der standortgebundenen Rohstoffwirtschaft.

Data Mining at NASA: From Theory to Applications

Science.gov (United States)

Srivastava, Ashok N.

2009-01-01

This slide presentation demonstrates the data mining/machine learning capabilities of NASA Ames and Intelligent Data Understanding (IDU) group. This will encompass the work done recently in the group by various group members. The IDU group develops novel algorithms to detect, classify, and predict events in large data streams for scientific and engineering systems. This presentation for Knowledge Discovery and Data Mining 2009 is to demonstrate the data mining/machine learning capabilities of NASA Ames and IDU group. This will encompass the work done re cently in the group by various group members.

Diesel aftertreatment control technologies in underground mines : the NO{sub 2} issue

Energy Technology Data Exchange (ETDEWEB)

Cauda, E.G.; Bugarski, A.D.; Patts, L. [National Inst. for Occupational Safety and Health, Pittsburgh, PA (United States). Office of Mine Safety and Health Research

2010-07-01

Diesel engines are the main source of exposure for underground miners to nitric oxide (NO) and nitrogen dioxide (NO{sub 2}). The exposure of underground miners to both these pollutants is regulated by the Mine Safety and Health Administration. Improvements have been made in mine ventilation in an attempt to meet more stringent emission limits. In coal mines in the United States, the exposure limits of underground miners to pollutant concentrations determine the ventilation rate specific for certified diesel engines. The ventilation rates are based on the amount of fresh air needed to dilute CO, CO{sub 2}, NO, NO{sub 2} in the undiluted exhaust gas to the threshold limit values (TLV). This presentation described the other options available to mine operators to reduce diesel particulate matter emissions. More advanced engine technologies, aftertreatment control strategies and the use of biodiesel fuels can reduce the mass concentrations of diesel particulate matter (DPM). However, these strategies can also alter tailpipe emissions of NO{sub 2} and an increase in ventilation rate may be required if the concentration of NO{sub 2} exceeds the regulatory enforced limit. The effects of different exhaust aftertreatment technologies were reviewed in this presentation along with ventilation control strategies for underground mining. 43 refs., 3 figs.

Fuzzy linear model for production optimization of mining systems with multiple entities

Science.gov (United States)

Vujic, Slobodan; Benovic, Tomo; Miljanovic, Igor; Hudej, Marjan; Milutinovic, Aleksandar; Pavlovic, Petar

2011-12-01

Planning and production optimization within multiple mines or several work sites (entities) mining systems by using fuzzy linear programming (LP) was studied. LP is the most commonly used operations research methods in mining engineering. After the introductory review of properties and limitations of applying LP, short reviews of the general settings of deterministic and fuzzy LP models are presented. With the purpose of comparative analysis, the application of both LP models is presented using the example of the Bauxite Basin Niksic with five mines. After the assessment, LP is an efficient mathematical modeling tool in production planning and solving many other single-criteria optimization problems of mining engineering. After the comparison of advantages and deficiencies of both deterministic and fuzzy LP models, the conclusion presents benefits of the fuzzy LP model but is also stating that seeking the optimal plan of production means to accomplish the overall analysis that will encompass the LP model approaches.

1998 mines and quarries guidebook

International Nuclear Information System (INIS)

1998-01-01

The 1998 edition of the mines and quarries guidebook provides: a comprehensive overview of mining activities in France and French-speaking countries relative to coal, uranium, non-ferrous ores and metals, industrial minerals, lime, limestone, silica, cermet and saline minerals; a list of recycling companies; a list of quarries and building material exploitations (organisational structure of main companies, granulates, cement industry, gypsum, plaster, tiles, bricks, stones..); a list and coordinates by department of more than 1400 quarries with the material exploited; an inventory of mining exploitations of Belgium, Switzerland and French speaking countries of Africa, a listing and organisational structure of research and engineering centres and administrations; an alphabetical and analytical repertory of more than 700 supplying companies of the mineral industry; and the status, organization and members of the mineral industry society. (J.S.)

Seismic Search Engine: A distributed database for mining large scale seismic data

Science.gov (United States)

Liu, Y.; Vaidya, S.; Kuzma, H. A.

2009-12-01

The International Monitoring System (IMS) of the CTBTO collects terabytes worth of seismic measurements from many receiver stations situated around the earth with the goal of detecting underground nuclear testing events and distinguishing them from other benign, but more common events such as earthquakes and mine blasts. The International Data Center (IDC) processes and analyzes these measurements, as they are collected by the IMS, to summarize event detections in daily bulletins. Thereafter, the data measurements are archived into a large format database. Our proposed Seismic Search Engine (SSE) will facilitate a framework for data exploration of the seismic database as well as the development of seismic data mining algorithms. Analogous to GenBank, the annotated genetic sequence database maintained by NIH, through SSE, we intend to provide public access to seismic data and a set of processing and analysis tools, along with community-generated annotations and statistical models to help interpret the data. SSE will implement queries as user-defined functions composed from standard tools and models. Each query is compiled and executed over the database internally before reporting results back to the user. Since queries are expressed with standard tools and models, users can easily reproduce published results within this framework for peer-review and making metric comparisons. As an illustration, an example query is “what are the best receiver stations in East Asia for detecting events in the Middle East?” Evaluating this query involves listing all receiver stations in East Asia, characterizing known seismic events in that region, and constructing a profile for each receiver station to determine how effective its measurements are at predicting each event. The results of this query can be used to help prioritize how data is collected, identify defective instruments, and guide future sensor placements.

A Design Theory for Requirements Mining Systems

OpenAIRE

Meth, Hendrik

2013-01-01

Software requirements are often communicated in unstructured text documents, which need to be analyzed in order to identify and classify individual needs. This process is referred to as requirements mining in the context of this thesis. It is known to be time-consuming and error-prone when performed manually by a requirements engineer. Thus, there is a demand to support requirements mining through information technology. However, little research has been conducted to conceptualize theoretical...

Engineering Perspectives and Environmental Life Cycle Optimization to Enhance Aggregate Mining in Vietnam

Directory of Open Access Journals (Sweden)

Petra Schneider

2018-02-01

Full Text Available Cleaner Production (CP addresses precautionary, site-specific environmental measures to reduce emissions and assess resource efficiency potentials at the point of origin by analyzing operational material and energy flows. The approach is generally based on the criteria quality as well as environmental/occupational health and safety, and promotes their integration. The paper presents options for applying CP to aggregate mining, based on a Life Cycle Assessment (LCA and illustrated by results from a study of small-scale industrial aggregate mining in Hoa Binh Province (Vietnam. The regulatory framework to limit the impact of mining on the environment is largely comparable to international standards and is suitably enforced. Despite gaining experience through the practical handling of enforcement procedures over the long term, there is still a considerable potential to optimize CP strategies in Vietnam’s aggregate mining industry. This is shown by the results of a survey of aggregates mining companies in Hoa Binh Province as well as on-site data collection to determine the technological characteristics of production facilities alongside economic and environmental factors. The assessment of the survey is supported by LCA results for: (a the existing situation; and (b the scenario of a merging of companies, undertaken to improve the resource efficiency of the aggregate mining in Hoa Binh. Findings can help implement an integrated approach to foster the sustainable mining of building aggregates.

Mine Planning for Asteroid Orebodies

Science.gov (United States)

Gertsch, L. S.; Gertsch, R. E.

2000-01-01

Given that an asteroid (or comet) has been determined to contain sufficient material of value to be potentially economic to exploit, a mining method must be selected and implemented. This paper discusses the engineering necessary to bring a mine online, and the opportunities and challenges inherent in asteroid mineral prospects. The very important step of orebody characterization is discussed elsewhere. The mining methods discussed here are based on enclosing the asteroid within a bag in some fashion, whether completely or partially. In general, asteroid mining methods based on bags will consist of the following steps. Not all will be required in every case, nor necessarily in this particular sequence. Some steps will be performed simultaneously. Their purpose is to extract the valuable material from the body of the asteroid in the most efficient, cost-effective manner possible. In approximate order of initiation, if not of conclusion, the steps are: 1. Tether anchoring to the asteroid. 2. Asteroid motion control. 3. Body/fragment restraint system placement. 4. Operations platform construction. 5. Bag construction. 6. Auxiliary and support equipment placement. 7. Mining operations. 8. Processing operations. 9. Product transport to markets.

The Hybrid Expert in the "Bergstaat": Anton Von Ruprecht as a Professor of Chemistry and Mining and as a Mining Official, 1779-1814

Science.gov (United States)

Konecny, Peter

2012-01-01

In the course of the 18th century a new type of scientifically educated functional elites developed, who were trained to administer mines. The educational project that led to the formation of a corps of mining engineers was part of a programme of administrative and economic reforms that led to a new configuration of bonds between state, economy…

Applying Web Usage Mining for Personalizing Hyperlinks in Web-Based Adaptive Educational Systems

Science.gov (United States)

Romero, Cristobal; Ventura, Sebastian; Zafra, Amelia; de Bra, Paul

2009-01-01

Nowadays, the application of Web mining techniques in e-learning and Web-based adaptive educational systems is increasing exponentially. In this paper, we propose an advanced architecture for a personalization system to facilitate Web mining. A specific Web mining tool is developed and a recommender engine is integrated into the AHA! system in…

Role of support services in Jaduguda mine

International Nuclear Information System (INIS)

Roy, Pinaki; Bannerjee, S.N.; Srinivasan, M.N.; Radhakrishnan, V.N.; Khanwalkar, S.D.

1991-01-01

This paper highlights the role of the supporting services which are divided into two main groups. Group A consists of services rendered by survey, planning, geology and physics sub-groups. The survey sub-group enforces the directional controls of the various lay-outs, the underground geology sub-group establishes the parameters for the development of drives and stop blocks while the physics section supplies the data regarding grade and thickness and exercises the ore quality control. The techniques evolved in giving these supports to the production system is described. Diamond drilling of holes through rock formation have been successfully used for transporting stowing sand and for draining accumulated water in the levels to respective sumps besides its normal use for underground exploration. Group B consists of engineering services. With limited mining machinery in the early sixties, the mechanical engineering services have taken significant strides for servicing today's equipments consisting of drill jumbos, hydro-pneumatic trackless loaders. Alimak raises climbers, diesel locomotives and mechanised ore transfer systems besides servicing the vital area of modern koepe system of friction winding where Jaduguda has already been a fore-runner in the country. Electrical engineering services basically maintain the electrical systems and equipments both permanent and extensions as mining areas progress in depth. Indigenisation of imported equipments and spares for them and modernisation in certain key areas has been attempted successfully over the years. Civil engineering services are mostly confined to strengthening support system for mine tunnels and construction of ore transfer passes for stopping. (author). 3 figs

Coal graders in Czechoslovakian mines

Energy Technology Data Exchange (ETDEWEB)

Vasek, J.; Klimek, M.

1980-01-01

Problems related to sections of the area of application of graders depending on different mining and geological mining-engineering factors are examined. The principal factors are selected from a general group of influencing factors: dip angle of a formation, separability (shear ability) of coal, characteristics of country rocks, adhesion of coal to rock, tectonic fracturing of a seam, and thickness of a formation. Based on practical and theoretical studies all of the principal factors have been categorized. This allows one to obtain an objective picture of the possibility of using graders under specific conditions by comparing different factors.

Mining method selection by integrated AHP and PROMETHEE method.

Science.gov (United States)

Bogdanovic, Dejan; Nikolic, Djordje; Ilic, Ivana

2012-03-01

Selecting the best mining method among many alternatives is a multicriteria decision making problem. The aim of this paper is to demonstrate the implementation of an integrated approach that employs AHP and PROMETHEE together for selecting the most suitable mining method for the "Coka Marin" underground mine in Serbia. The related problem includes five possible mining methods and eleven criteria to evaluate them. Criteria are accurately chosen in order to cover the most important parameters that impact on the mining method selection, such as geological and geotechnical properties, economic parameters and geographical factors. The AHP is used to analyze the structure of the mining method selection problem and to determine weights of the criteria, and PROMETHEE method is used to obtain the final ranking and to make a sensitivity analysis by changing the weights. The results have shown that the proposed integrated method can be successfully used in solving mining engineering problems.

Enrolment regimes and gender differences in university of mines ...

African Journals Online (AJOL)

These perceptions, the general dislike for engineering courses by most females for fear of mathematics and the knowledge of the fact that engineering is quite difficult, explain the phenomenon of female under-representation in the mines. Though the progressive feminine enrolment regimes, due to gender main streaming ...

Numerical simulation of phenomenon on zonal disintegration in deep underground mining in case of unsupported roadway

Science.gov (United States)

Han, Fengshan; Wu, Xinli; Li, Xia; Zhu, Dekang

2018-02-01

Zonal disintegration phenomenon was found in deep mining roadway surrounding rock. It seriously affects the safety of mining and underground engineering and it may lead to the occurrence of natural disasters. in deep mining roadway surrounding rock, tectonic stress in deep mining roadway rock mass, horizontal stress is much greater than the vertical stress, When the direction of maximum principal stress is parallel to the axis of the roadway in deep mining, this is the main reasons for Zonal disintegration phenomenon. Using ABAQUS software to numerical simulation of the three-dimensional model of roadway rupture formation process systematically, and the study shows that when The Direction of maximum main stress in deep underground mining is along the roadway axial direction, Zonal disintegration phenomenon in deep underground mining is successfully reproduced by our numerical simulation..numerical simulation shows that using ABAQUA simulation can reproduce Zonal disintegration phenomenon and the formation process of damage of surrounding rock can be reproduced. which have important engineering practical significance.

Integration of MOOCs in Advanced Mining Training Programmes

Science.gov (United States)

Saveleva, Irina; Greenwald, Oksana; Kolomiets, Svetlana; Medvedeva, Elena

2017-11-01

The paper covers the concept of innovative approaches in education based on incorporating MOOCs options into traditional classroom. It takes a look at the ways higher education instructors working with the mining engineers enrolled in advanced training programmes can brighten, upgrade and facilitate the learning process. The shift of higher education from in-class to online format has changed the learning environment and the methods of teaching including professional retraining courses. In addition, the need of mining companies for managers of a new kind obligates high school retraining centres rapidly move towards the 21st century skill framework. One of widely recognized innovations in the sphere of e-learning is MOOCs (Massive Open Online Courses) that can be used as an effective teaching tool for organizing professional training of managing staff of mining companies within the walls of a university. The authors share their instructional experience and show the benefits of introducing MOOCs options at the courses designed for retraining mining engineers and senior managers of coal enterprises. Though in recent researches the pedagogical value of MOOCs is highly questioned and even negated this invention of the 21st century can become an essential and truly helpful instrument in the hands of educators.

Nursing lives in the blogosphere: A thematic analysis of anonymous online nursing narratives.

Science.gov (United States)

Castro, Aimee; Andrews, Gavin

2018-02-01

The aim of this study was to explore the work-life narratives of nurses through a thematic analysis of the nursing accounts they post in their publicly accessible, anonymous blogs. Many nurses participate on social media. Blogs have been advocated as a self-reflective tool in nursing practice, yet as far as the authors are aware, no previous studies have explored nurses' individual blogs for their potential to reveal nurses' perceptions of nursing work. The research design was qualitative description. Between May-August 2015, Internet search engines were used to discover lists of nursing blogs recommended by organizations representing nurses' interests. Recommended blogs were purposively sampled. Four anonymous blogs written by nurses from different nursing specialties met the sampling criteria. All 520 of their entries from 2014 were read and copied into NVivo 10, where an inductive coding process was followed. Three major themes arose in these nurses' online discussions of their work lives: they truly care about and value their nursing work, but they are feeling stressed and burnt out and they are using their anonymous blogs to share factors that frustrate them in their nursing work. Three main areas of frustration were revealed: teamwork problems, challenging patients and families, and management issues. Anonymous nursing blogs offer valuable, longitudinal insights into nurses' perceptions of their work lives. Nursing blogs should be further explored for ongoing insights into nurses' experiences of nursing work, as well as nurses' recommendations for addressing issues causing them to feel frustrated in their work environments. © 2017 John Wiley & Sons Ltd.

Presentations from the 1992 Coal Mining Impoundment Informational Meeting

Energy Technology Data Exchange (ETDEWEB)

1993-12-31

On May 20 and 21, 1992, the MSHA Coal Mining Impoundment Informational Meeting was held at the National Mine Health and Safety Academy in Beckley, West Virginia. Fifteen presentations were given on key issues involved in the design and construction of dams associated with coal mining. The attendees were told that to improve the consistency among the plan reviewers, engineers from the Denver and Pittsburgh Technical Support Centers meet twice annually to discuss specific technical issues. It was soon discovered that the topics being discussed needed to be shared with anyone involved with coal waste dam design, construction, or inspection. The only way to accomplish that goal was through the issuance of Procedure Instruction Letters. The Letters present a consensus of engineering philosophy that could change over time. They do not present policy or carry the force of law. Currently, thirteen position papers have been disseminated and more will follow as the need arises. The individual paper were not even entered into the database.

The environmental impact of mine wastes - roles of microorganisms and their significance in treatment of mine wastes

International Nuclear Information System (INIS)

Ledin, M.; Pedersen, K.

1996-01-01

Mine wastes constitute a potential source of contamination to the environment, as heavy metals and acid are released in large amounts. A great variety of microorganisms has been found in mine wastes and microbiological processes are usually responsible for the environmental hazard created by mine wastes. However, microorganisms can also be used to retard the adverse impact of mine wastes on the environment. Conventionally, the mine drainage as well as the waste itself can be treated with alkali to increase pH and precipitate metals. The main drawback of this method is that it has to be continuously repeated to be fully effective. There may also be negative effects on beneficial microorganisms. Several other treatment methods have been developed to stop weathering processes thereby reducing the environmental impact of mine wastes. The other main approach is to treat the drainage water. Various methods aim at using microorganisms for this in natural or engineered systems. Recently, much interest has been focused on the use of natural or artificial wetlands for treatment. In general, the activity of microorganisms is neglected in the design of mine waste treatment systems, and the treatments are created merely from a technical point of view. This can result in situations where unexpected microbial processes take over, and, in the worst scenario, the overall effect is opposite to the desired

Implementing of action plans for risk communication on the uranium mining sites remedy at Ningyo-toge Environmental Engineering Center (2) (Contract research)

International Nuclear Information System (INIS)

Yabuta, Naohiro; Kawai, Jun; Hikawa, Tamae; Tokizawa, Takayuki; Sato, Kazuhiko; Koga, Osamu

2008-11-01

On the closure of uranium mine site at Ningyo-Toge Environmental Engineering Center Japan Atomic Energy Agency, the action plans for risk communication with residence and local governments were developed and implemented. Under a practical program of the risk communication, an ethnographical research on Ningyo-Toge Environmental Engineering Center has been conducted by local high school students. The research was focused on several social groups such as engineers at the Center and residents around Ningyo-Toge and described their circumstances from the past to the present, since the discovery of the uranium outcrop 1955. In the second year of the program, the results of the research were presented at symposium and the students had opportunities to exchange their views with others from different high schools that held in similar programs. Through those activities, the importance of the program was rediscovered and some new issues were also identified. (author)

Improving the energy efficiency of mine fan assemblages

International Nuclear Information System (INIS)

De Souza, Euler

2015-01-01

Energy associated with ventilating an underground operation comprises a significant portion of a mine operation's base energy demand and is consequently responsible for a large percentage of the total operating costs. Ventilation systems may account from 25 to 40% of the total energy costs and 40–50% of the energy consumption of a mine operation. Fans are the most important mechanical devices used to ventilate underground mines and the total fan power installed in a single mine operation can easily exceed 10,000 kW. Investigations of a number of mine main fan installations have determined their assemblage to be, in general, very energy inefficient. The author has found that 40–80% of the energy consumed by a main fan is used to overcome the resistance of fan assemblage components. This paper presents how engineering design principles can be applied to improve the performance and efficiency of fan installations, resulting in substantial reductions in power consumption, operating cost and greenhouse gas emissions. A detailed case study is presented to demonstrate that, by designing fan assemblages using proper engineering concepts of fluid physics and industrial ventilation design, main fan systems will operate at efficiencies well above 80–90% (compared to common operating efficiencies of between 20 and 65%), resulting in a drastic reduction in a mine's overall costs and base electrical and energy loads. - Highlights: • Increases in fan assemblage efficiencies with minimum capital investment. • Improved designs for substantial fan power and operating cost savings. • General solutions and tactics for improving existing main fan installations. • Case study presented to demonstrate proper design of fan assemblages.

Introductory Anatomy and Physiology in an Undergraduate Nursing Curriculum

Science.gov (United States)

Brown, S. J.; White, S.; Power, N.

2017-01-01

Using an educational data mining approach, first-year academic achievement of undergraduate nursing students, which included two compulsory courses in introductory human anatomy and physiology, was compared with achievement in a final semester course that transitioned students into the workplace. We hypothesized that students could be grouped…

Exploring the techno-economic feasibility of mine rock waste utilisation in road works: The case of a mining deposit in Ghana.

Science.gov (United States)

Agyeman, Stephen; Ampadu, Samuel I K

2016-02-01

Mine rock waste, which is the rock material removed in order to access and mine ore, is free from gold processing chemical contaminants but presents a significant environmental challenge owing to the large volumes involved. One way of mitigating the environmental and safety challenges posed by the large volume of mine rock waste stockpiled in mining communities is to find uses of this material as a substitute for rock aggregates in construction. This article reports on a study conducted to evaluate the engineering properties of such a mine deposit to determine its suitability for use as road pavement material. Samples of mine rock waste, derived from the granitic and granodioritic intrusive units overlying the gold-bearing metavolcanic rock and volcano-clastic sediments of a gold mining area in Ghana, were obtained from three mine rock waste disposal facilities and subjected to a battery of laboratory tests to determine their physical, mechanical, geotechnical, geometrical and durability properties. The overall conclusion was that the mine rock waste met all the requirements of the Ghana Ministry of Transportation specification for use as aggregates for crushed rock subbase, base and surface dressing chippings for road pavements. The recommendation is to process it into the required sizes for the various applications. © The Author(s) 2015.

Education of mining engineers with the specialization in Rescue, fire and safety technique at the BERG Faculty of the Technical University of Košice

Directory of Open Access Journals (Sweden)

Sedlatý Václav

2002-12-01

Full Text Available After the separation of Czechoslovakia, in 1993, the Mining Faculty (now BERG Faculty of the Technical University of Košice started a teaching program with the specialization in mining rescue, fire guard and safety technique at the Detachment in Prievidza, because of all the needs and conditions related to the education of engineers in the mentioned areas. During the last 10 years, the Detachment in Prievidza has been growing in terms of number of students. From the beginning of this period to present days 75 students graduated. The full-time studies last five years and the academic years are divided into two semesters of 15 weeks each. The semesters are finished by examination sessions. The first 2 years, in principle, include basic studies in mathematics, scientific subjects and some subjects related to earth sciences. The third and fourth year are generally devoted to basic technical subjects of mining and underground works, and then to rescue, fire and safety subjects. A practical work experience has to be gained by students in a mine or fire and safety stations. The practical training term is scheduled after the third academic year. During the last two semesters the students are preparing their Master’s degree thesis using a stay in the mine company or other firms to receive the necessary information and data.

Personalized links recommendation based on data mining in adaptive educational hypermedia systems

NARCIS (Netherlands)

Romero, C.; Ventura, S.; Delgado, J.A.; De Bra, P.M.E.; Duval, E.; Klamma, R.; Wolpers, M.

2007-01-01

In this paper, we describe a personalized recommender system that uses web mining techniques for recommending a student which (next) links to visit within an adaptable educational hypermedia system. We present a specific mining tool and a recommender engine that we have integrated in the AHA! system

Engineer exchanging project (coal mine technology field) in fiscal 1999. International information exchanging project (advance survey on Russia); 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Jizen chosa (Roshia)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This advance survey on Russia has performed visiting surveys and information collection at coal related organizations inside Japan and in overseas countries on production technology levels, trends and technology exchange needs in overseas coal producing countries. The project is intended to serve for improvement in the contents of and smooth execution of the engineer exchange project in the 'coal mine technology field. It was carried out by expertise people as the site surveys and the engineer reception and exchange surveys. Because of the economic crisis that has hit Russia in 1998, unprofitable coal mines were closed one after another under the coal mine scrap and build policy under the initiative of the World Bank. This situation is giving serious impacts on coal mines in the Far East Russia and the coastal areas. However, the importance of coal as the primary energy source has not been changed at all in the Far East Russia. Thus, the areas have fallen into a situation that they must rely on a great amount of introduced and imported coals as a result of weakening in coal mines in the Far Eastern area on the other hand. This paper reports mainly the situation in which the coal industries in the coastal areas are placed, and the possibilities of technology exchange. (NEDO)

Modeling the complex activity of sickle cell and thalassemia specialist nurses in England.

Science.gov (United States)

Leary, Alison; Anionwu, Elizabeth N

2014-01-01

Specialist advanced practice nursing in hemoglobinopathies has a rich historical and descriptive literature. Subsequent work has shown that the role is valued by patients and families and also by other professionals. However, there is little empirical research on the complexity of activity of these services in terms of interventions offered. In addition, the work of clinical nurse specialists in England has been devalued through a perception of oversimplification. The purpose of this study was to understand the complexity of expert nursing practice in sickle cell and thalassemia. The approach taken to modeling complexity was used from common methods in mathematical modeling and computational mathematics. Knowledge discovery through data was the underpinning framework used in this study using a priori mined data. This allowed categorization of activity and articulation of complexity. In total, 8966 nursing events were captured over 1639 hours from a total of 22.8 whole time equivalents, and several data sources were mined. The work of specialist nurses in this area is complex in terms of the physical and psychosocial care they provide. The nurses also undertook case management activity such as utilizing a very large network of professionals, and others participated in admission avoidance work and education of patients' families and other staff. The work of nurses specializing in hemoglobinopathy care is complex and multidimensional and is likely to contribute to the quality of care in a cost-effective way. An understanding of this complexity can be used as an underpinning to establishing key performance indicators, optimum caseload calculations, and economic evaluation.

School Nurse Workload: A Scoping Review of Acute Care, Community Health, and Mental Health Nursing Workload Literature

Science.gov (United States)

Endsley, Patricia

2017-01-01

The purpose of this scoping review was to survey the most recent (5 years) acute care, community health, and mental health nursing workload literature to understand themes and research avenues that may be applicable to school nursing workload research. The search for empirical and nonempirical literature was conducted using search engines such as…

Proceedings of the 3. Canada-US rock mechanics symposium and 20. Canadian rock mechanics symposium : rock engineering 2009 : rock engineering in difficult conditions

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

This conference provided a forum for geologists, mining operators and engineers to discuss the application of rock mechanics in engineering designs. Members of the scientific and engineering communities discussed challenges and interdisciplinary elements involved in rock engineering. New geological models and methods of characterizing rock masses and ground conditions in underground engineering projects were discussed along with excavation and mining methods. Papers presented at the conference discussed the role of rock mechanics in forensic engineering. Geophysics, geomechanics, and risk-based approaches to rock engineering designs were reviewed. Issues related to high pressure and high flow water conditions were discussed, and new rock physics models designed to enhance hydrocarbon recovery were presented. The conference featured 84 presentations, of which 9 have been catalogued separately for inclusion in this database. tabs., figs.

Engineer exchanging project on coal mine technology field in fiscal 1999. International information exchanging project (the overseas workshop in Vietnam); 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop (Vietnam)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Technical information exchange was performed with Vietnamese engineers related to coal mine technologies through the overseas workshop and the technical tour. At the same time, investigations were executed on the production technology levels and needs in Vietnam, and on possibilities of transfer of Japanese technologies. The 'Overseas workshop (Vietnam)' was held on September 28, 1999 with the 'trends and problems in coal production technologies' as the main theme. Lectures were given in the session related to coal production technologies by Vietnamese coal technology experts, each from VINACOAL and IMSAT, and by two Japanese coal technology experts. A comprehensive discussion was also executed, and items of technical information were exchanged on the coal production technologies. The number of persons actually participated in the workshop counted 58, with the proceedings presented by them distributed. The Mao Khe and Duong Huy coal mines in Quang Ninh Province were visited as the technical tour, whereas the coal mine sites were inspected and opinions were exchanged with the site engineers. Gas analysis was performed in the Mao Khe mine from the viewpoint of a gas control technology, and site investigation was carried out on lock bolts in the Duong Huy mine from the viewpoint of a roof control technology. (NEDO)

Emotional intelligence among nursing students: Findings from a cross-sectional study.

Science.gov (United States)

Štiglic, Gregor; Cilar, Leona; Novak, Žiga; Vrbnjak, Dominika; Stenhouse, Rosie; Snowden, Austyn; Pajnkihar, Majda

2018-07-01

Emotional intelligence in nursing is of global interest. International studies identify that emotional intelligence influences nurses' work and relationships with patients. It is associated with compassion and care. Nursing students scored higher on measures of emotional intelligence compared to students of other study programmes. The level of emotional intelligence increases with age and tends to be higher in women. This study aims to measure the differences in emotional intelligence between nursing students with previous caring experience and those without; to examine the effects of gender on emotional intelligence scores; and to test whether nursing students score higher than engineering colleagues on emotional intelligence measures. A cross-sectional descriptive study design was used. The study included 113 nursing and 104 engineering students at the beginning of their first year of study at a university in Slovenia. Emotional intelligence was measured using the Trait Emotional Intelligence Questionnaire (TEIQue) and Schutte Self Report Emotional Intelligence Test (SSEIT). Shapiro-Wilk's test of normality was used to test the sample distribution, while the differences in mean values were tested using Student t-test of independent samples. Emotional intelligence was higher in nursing students (n = 113) than engineering students (n = 104) in both measures [TEIQue t = 3.972; p emotional intelligence scores than male students on both measures, the difference was not statistically significant [TEIQue t = -0.839; p = 0.403; SSEIT t = -1.159; p = 0.249]. EI scores in nursing students with previous caring experience were not higher compared to students without such experience for any measure [TEIQue t = -1.633; p = 0.105; SSEIT t = -0.595; p = 0.553]. Emotional intelligence was higher in nursing than engineering students, and slightly higher in women than men. It was not associated with previous caring experience. Copyright

[Aspects for data mining implementation in gerontology and geriatrics].

Science.gov (United States)

Mikhal'skiĭ, A I

2014-01-01

Current challenges facing theory and practice in ageing sciences need new methods of experimental data investigation. This is a result as of experimental basis developments in biological research, so of information technology progress. These achievements make it possible to use well proven in different fields of science and engineering data mining methods for tasks in gerontology and geriatrics. Some examples of data mining methods implementation in gerontology are presented.

Mine drivage in hydraulic mines

Energy Technology Data Exchange (ETDEWEB)

Ehkber, B Ya

1983-09-01

From 20 to 25% of labor cost in hydraulic coal mines falls on mine drivage. Range of mine drivage is high due to the large number of shortwalls mined by hydraulic monitors. Reducing mining cost in hydraulic mines depends on lowering drivage cost by use of new drivage systems or by increasing efficiency of drivage systems used at present. The following drivage methods used in hydraulic mines are compared: heading machines with hydraulic haulage of cut rocks and coal, hydraulic monitors with hydraulic haulage, drilling and blasting with hydraulic haulage of blasted rocks. Mining and geologic conditions which influence selection of the optimum mine drivage system are analyzed. Standardized cross sections of mine roadways driven by the 3 methods are shown in schemes. Support systems used in mine roadways are compared: timber supports, roof bolts, roof bolts with steel elements, and roadways driven in rocks without a support system. Heading machines (K-56MG, GPKG, 4PU, PK-3M) and hydraulic monitors (GMDTs-3M, 12GD-2) used for mine drivage are described. Data on mine drivage in hydraulic coal mines in the Kuzbass are discussed. From 40 to 46% of roadways are driven by heading machines with hydraulic haulage and from 12 to 15% by hydraulic monitors with hydraulic haulage.

Proceedings of the 11. annual mining industry learning seminar : 2006 equipment evolutions

Energy Technology Data Exchange (ETDEWEB)

Joseph, T. [Alberta Univ., Edmonton, AB (Canada). School of Mining and Petroleum Engineering] (comp.)

2006-07-01

This seminar provided a forum for mine engineers, geologists, operators, vendors and academics to discuss various topics on equipment evolution that address mining industry concerns. Participants included those who are involved in mine planning, equipment selection, operations and maintenance. The presentations identified possible solutions to ongoing issues and alternative technologies emerging in the mining industry. Operators and original equipment manufacturers shared their innovations in novel developments and presented solutions to issues relevant to mining processes including truck and shovel technology issues such as tires, lube and fuel emissions. The seminar featured 17 presentations, of which 5 have been catalogued separately for inclusion in this database. tabs., figs.

Ghana Mining Journal - Vol 15, No 1 (2015)

African Journals Online (AJOL)

... on Post Processed Differential Global Positioning System (DGPS) Data – A Case ... Application of Surpac and Whittle Software in Open Pit Optimisation and ... What's on the Minds of Beginner Mining and Related Engineering Students?

Heavy metal accumulation and ecosystem engineering by two common mine site-nesting ant species: implications for pollution-level assessment and bioremediation of coal mine soil.

Science.gov (United States)

Khan, Shbbir R; Singh, Satish K; Rastogi, Neelkamal

2017-04-01

The present study focuses on the abundance, heavy metal content, and the impact of ecosystem engineering activities of two coal mine site-inhabiting ant species, Cataglyphis longipedem and Camponotus compressus. The abundance of Ct. longipedem increased while that of C. compressus decreased, with increasing soil pollution. Correspondence analysis reveals a close association between soil heavy metal concentrations and Ct. longipedem abundance, but this association is lacking in the case of C. compressus. Cataglyphis ants which occupy stress-characterized niches appear to be pre-adapted to tolerate heavy metal pollution. Higher concentrations of Zn and Mn in Ct. longipedem may contribute to the strengthening of the cuticular structures, necessary for nest excavation in the hard, arid soil and for single load carrying. C. compressus ants appear to be pollution sensitive. Their higher Fe content may be related to metal uptake via plant-derived liquids and species-specific regulatory mechanisms. The metal pollution index and biota-to-soil accumulation factors, calculated by using the ant body metal content of the two species, indicate an overall decrease of soil heavy metal concentrations with increase of the site age, which reflects the degree of pollution related to the mine site age. The concentrations of total and available heavy metals (Fe, Zn, Mn, Pb, and Cu) were significantly lower in the ant nest debris soil as compared to the reference soil. The results of the present study highlight the role of ants as bioindicators and in bioremediation of contaminated soil.

Manual of acid in situ leach uranium mining technology

International Nuclear Information System (INIS)

2001-08-01

In situ leaching (ISL) technology recovers uranium using two alternative chemical leaching systems - acid and alkaline. This report brings together information from several technical disciplines that are an essential part of ISL technology. They include uranium geology, geohydrology, chemistry as well as reservoir engineering and process engineering. This report provides an extensive description of acid ISL uranium mining technology

Manual of acid in situ leach uranium mining technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-08-01

In situ leaching (ISL) technology recovers uranium using two alternative chemical leaching systems - acid and alkaline. This report brings together information from several technical disciplines that are an essential part of ISL technology. They include uranium geology, geohydrology, chemistry as well as reservoir engineering and process engineering. This report provides an extensive description of acid ISL uranium mining technology.

Fiscal 1998 engineer interexchange project (coal mine technology field). Preliminary survey on the international interexchange project in America; 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Jizen chosa (Beikoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the fiscal 1998 international interexchange project in a coal mine technology field, the survey was made in America. Geological engineering problem has large effect on the protection and productivity of underground coal mines. Promotion of long wall mining has contributed to reduction of disasters, however, recently deaths due to roof collapse and wall collapse are on the increase. A roof evaluation technique was developed for adequate selection of mining methods and support design, and its standardization and diffusion are in promotion. Integration and improvement advanced in facility technology because of worldwide integration by acquisition of coal mine facility manufacturers. Introduction of high-power high-capacity facilities is increasing with introduction of large long wall working faces, and development of rear transport system technology and labor saving by remote control are also in promotion according to such trend. As automation and labor saving technology of mining facilities, the automated direction detection and control system by laser and gyroscope is under development. (NEDO)

Personality and Education Mining based Job Advisory System

Directory of Open Access Journals (Sweden)

Rajendra S. Choudhary

2014-09-01

Full Text Available Every job demands an employee with some specific qualities in addition to the basic educational qualification. For example, an introvert person cannot be a good leader despite of a very good academic qualification. Thinking and logical ability is required for a person to be a successful software engineer. So, the aim of this paper is to present a novel approach for advising an ideal job to the job seeker while considering his personality trait and educational qualification both. Very well-known theories of personality like MBTI indicator and OCEAN theory, are used for personality mining. For education mining, score based system is used. The score based system captures the information from attributes like most scoring subject, dream job etc. After personality mining, the resultant values are coalesced with the information extracted from education mining. And finally, the most suited jobs, in terms of personality and educational qualification are recommended to the job seekers. The experiment is conducted on the students who have earned an engineering degree in the field of computer science, information technology and electronics. Nevertheless, the same architecture can easily be extended to other educational degrees also. To the best of the author’s knowledge, this is a first e-job advisory system that recommends the job best suited as per one’s personality using MBTI and OCEAN theory both.

Recovery of uranium in mine waters

International Nuclear Information System (INIS)

Sugier, P.

1967-01-01

In a brief introductory survey the author indicates the date on which leaching was first observed in the CEA mines and lists the main factors necessary for, or favourable to, the solubilization of uranium in mines. Information is given on the various sources of this type at present identified in France and the methods used to recover uranium in mines situated near ore-concentration plants. An explanation is given for the use of the calcium precipitation technique in connection with waters produced in mines not situated near ore-concentration plants. Data are given on the results of laboratory tests carried out on waters containing uranium, together with a description of an industrial-scale facility built in consequence of these tests. Details are given of the statistical results obtained. The author concludes by outlining the programme which will be implemented in the near future with a view to increasing the tonnage of uranium produced by in situ leaching and indicates that the CEA engineers are very optimistic about the prospects of this new low-cost method of producing uranium. (author) [fr

Analysis of the situation of Spanish metal mining

International Nuclear Information System (INIS)

Espi Rodriguez, J. A.; Vazquez Guzman, F.; Leon Altamirano, C.; Perez Macias, D.

2015-01-01

This article is a summary of the original document drawn up by the Task Force on Mineral Resources and Reserves of the National Association of Mining Engineers, available in free digital format through the Link. (Author)

Applying Rock Engineering Systems (RES approach to Evaluate and Classify the Coal Spontaneous Combustion Potential in Eastern Alborz Coal Mines

Directory of Open Access Journals (Sweden)

Amir Saffari

2013-12-01

Full Text Available Subject analysis of the potential of spontaneous combustion in coal layers with analytical and numerical methods has been always considered as a difficult task because of the complexity of the coal behavior and the number of factors influencing it. Empirical methods, due to accounting for certain and specific factors, have not accuracy and efficiency for all positions. The Rock Engineering Systems (RES approach as a systematic method for analyzing and classifying is proposed in engineering projects. The present study is concerned with employing the RES approach to categorize coal spontaneous combustion in coal regions. Using this approach, the interaction of parameters affecting each other in an equal scale on the coal spontaneous combustion was evaluated. The Intrinsic, geological and mining characteristics of coal seams were studied in order to identifying important parameters. Then, the main stages of implementation of the RES method i.e. interaction matrix formation, coding matrix and forming a list category were performed. Later, an index of Coal Spontaneous Combustion Potential (CSCPi was determined to format the mathematical equation. Then, the obtained data related to the intrinsic, geological and mining, and special index were calculated for each layer in the case study (Pashkalat coal region, Iran. So, the study offers a perfect and comprehensive classification of the layers. Finally, by using the event of spontaneous combustion occurred in Pashkalat coal region, an initial validation for this systematic approach in the study area was conducted, which suggested relatively good concordance in Pashkalat coal region.

On-Site Radon Detection of Mining-induced Fractures from Overlying Strata to the Surface: A Case Study of the Baoshan Coal Mine in China

Directory of Open Access Journals (Sweden)

Wei Zhang

2014-12-01

Full Text Available Large-scale longwall mining of shallow coal seams may cause mining-induced fractures that can project completely through to the surface. This could lead to a series of mine safety and environmental issues, further deteriorating the already fragile ecological environment in the Western mining areas in China. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures from overlying strata to the surface in the Baoshan Coal Mine (BCM. The on-site test indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.

Peabody Western brings its old mines into new competitive era

Energy Technology Data Exchange (ETDEWEB)

Sprouls, M.W.

1994-10-01

Peabody Western Coal Co., manages four surface mines that mark Peabody's expansion from the Midwest to the West. The mines began operating between 1964 and 1973, before the surge of western coal mine start-ups brought about by the oil price shock of 1973 and 1974 and the subsequent investments in coal by American oil companies. Despite good demand for western low-sulfur coals, the prices are low due to production overcapacity that was built in the 1970s. The result is that older mines have had to be creative to reduce costs and retain customers amid stiff competition. The mining units - Black Mesa and Kayenta in Arizona, Big Sky in Montana and Seneca in Colorado - now must handle coal supply administration, financial analysis, engineering, environmental compliance, labor relations and community relations at their sites. Peabody Western's Flagstaff, Ariz., headquarters staff will be reduced by about 30 people, although many of them will be assigned to mining units. All four surface mines use draglines, and each supplies a primary customer, but the mines have as many differences as similarities. Altogether, the mines produce about 17 million tons annually and employ 1,100 people.

Proceedings of the Sudbury 2003 Mining and the Environment Conference

International Nuclear Information System (INIS)

Spiers, G.; Beckett, P.; Conroy, H.

2003-01-01

Sudbury is considered to be the centre of the Canadian mining industry and has gained a reputation for environmentally sound mining practices that are being met through mine site rehabilitation and regional land reclamation. This international conference provided a forum to exchange ideas and information pertinent to mine reclamation activities. More than 400 delegates, including leading scientists and technical experts from around the world participated at the conference. Approximately 150 papers were presented on a wide range of topics related to mine site rehabilitation issues and environmental protection methods associated with mining. Both current and future challenges faced by the mining industry were discussed with particular reference to the long-term sustainability of the mining process. Topics of discussion included issues pertaining to reclamation and rehabilitation of disturbed lands and waterways as well as specific site reclamation challenges associated with the oil industry. Reclamation activities include a wide range of expertise including plant ecology, forestry, soil science, land use planning, civil and mine engineering, wildlife biology, and reclamation. Six papers from the conference have been processed separately for inclusion in this database. refs., tabs., figs

Optimized mine ventilation on demand (OMVOD)

International Nuclear Information System (INIS)

Anderson, M.

2009-01-01

This paper provided an overview of the Optimized Mine Ventilation on Demand (OMVOD) system that is being installed at Xstrata Nickel Rim South Project and at Vale Inco's Totten Mine in Sudbury. The OMVOD system is designed to dynamically monitor and control air quality and quantity in real time and dilute and remove hazardous substances including diesel particulate matter (DPM), carbon monoxide (CO) and nitrous oxide (NO 2 ). It is also designed to control the thermal environment and provide ventilation for humans as well as mobile equipment engine combustion according to regulatory standards. The paper highlighted the OMVOD system optimization of energy, air quality measurement and control and production management of the mines through real time dynamic automation. Topics of discussion included real-time tracking and monitoring of diesel equipment; real-time tracking of underground miners; real-time evaluation of mine ventilation networks; and real-time control and optimization of ventilation equipment. ABB and Simsmart Technologies have joined forces to provide underground mining customers with a ventilation optimization solution. Simsmart's OMVOD provides proven real time/dynamic automation technology to significantly reduce energy costs, provide health and safety benefits as well as major capital cost savings while realizing an increase in production.

Mining and mining authorities in Saarland 2016. Mining economy, mining technology, occupational safety, environmental protection, statistics, mining authority activities. Annual report

International Nuclear Information System (INIS)

2016-01-01

The annual report of the Saarland Upper Mining Authority provides an insight into the activities of mining authorities. Especially, the development of the black coal mining, safety and technology of mining as well as the correlation between mining and environment are stressed.

Mechanics of granular-frictional-visco-plastic fluids in civil and mining engineering

Science.gov (United States)

Alehossein, H.; Qin, Z.

2013-10-01

The shear stress generated in mine backfill slurries and fresh concrete contains both velocity gradient dependent and frictional terms, categorised as frictional viscous plastic fluids. This paper discusses application of the developed analytical solution for flow rate as a function of pressure and pressure gradient in discs, pipes and cones for such frictional Bingham-Herschel-Bulkley fluids. This paper discusses application of this continuum fluid model to industrial materials like mine and mineral slurries, backfills and fresh concrete tests.

Research on preventive technologies for bed-separation water hazard in China coal mines

Science.gov (United States)

Gui, Herong; Tong, Shijie; Qiu, Weizhong; Lin, Manli

2018-03-01

Bed-separation water is one of the major water hazards in coal mines. Targeted researches on the preventive technologies are of paramount importance to safe mining. This article studied the restrictive effect of geological and mining factors, such as lithological properties of roof strata, coal seam inclination, water source to bed separations, roof management method, dimensions of mining working face, and mining progress, on the formation of bed-separation water hazard. The key techniques to prevent bed-separation water-related accidents include interception, diversion, destructing the buffer layer, grouting and backfilling, etc. The operation and efficiency of each technique are corroborated in field engineering cases. The results of this study will offer reference to countries with similar mining conditions in the researches on bed-separation water burst and hazard control in coal mines.

Application of Kansei engineering and data mining in the Thai ceramic manufacturing

Science.gov (United States)

Kittidecha, Chaiwat; Yamada, Koichi

2018-01-01

Ceramic is one of the highly competitive products in Thailand. Many Thai ceramic companies are attempting to know the customer needs and perceptions for making favorite products. To know customer needs is the target of designers and to develop a product that must satisfy customers. This research is applied Kansei Engineering (KE) and Data Mining (DM) into the customer driven product design process. KE can translate customer emotions into the product attributes. This method determines the relationships between customer feelings or Kansei words and the design attributes. Decision tree J48 and Class association rule which implemented through Waikato Environment for Knowledge Analysis (WEKA) software are used to generate a predictive model and to find the appropriate rules. In this experiment, the emotion scores were rated by 37 participants for training data and 16 participants for test data. 6 Kansei words were selected, namely, attractive, ease of drinking, ease of handing, quality, modern and durable. 10 mugs were selected as product samples. The results of this study indicate that the proposed models and rules can interpret the design product elements affecting the customer emotions. Finally, this study provides useful understanding for the application DM in KE and can be applied to a variety of design cases.

Staffing and job satisfaction: nurses and nursing assistants.

Science.gov (United States)

Kalisch, Beatrice; Lee, Kyung Hee

2014-05-01

The aim of this study was to examine the relationship between staffing and job satisfaction of registered nurses (RNs) and nursing assistants (NAs). Although a number of previous studies have demonstrated the link between the numbers of patients cared for on the last shift and/or perceptions of staffing adequacy, we could find only one study that utilized a measure of actual staffing (opposed to perceptions of staffing adequacy) and correlated it with job satisfaction of registered nurses. This cross-sectional study included 3523 RNs and 1012 NAs in 131 patient care units. Staff were surveyed to determine job satisfaction and demographic variables. In addition, actual staffing data were collected from each of the study units. Hours per patient day was a significant positive predictor for registered nurse job satisfaction after controlling for covariates. For NAs, a lower skill mix was marginally significant with higher job satisfaction. In addition, the more work experience the NAs reported, the lower their job satisfaction. Adequate staffing levels are essential for RN job satisfaction whereas NA job satisfaction depends on the number of assistive personnel in the mix of nursing staff. Two implications are (1) providing adequate staffing is critical to maintain RN job satisfaction and (2) the NA job needs to be re-engineered to make it a more attractive and satisfying career. © 2012 John Wiley & Sons Ltd.

A review on in situ phytoremediation of mine tailings.

Science.gov (United States)

Wang, Li; Ji, Bin; Hu, Yuehua; Liu, Runqing; Sun, Wei

2017-10-01

Mine tailings are detrimental to natural plant growth due to their physicochemical characteristics, such as high pH, high salinity, low water retention capacity, high heavy metal concentrations, and deficiencies in soil organic matter and fertility. Thus, the remediation of mine tailings has become a key issue in environmental science and engineering. Phytoremediation, an in situ cost-effective technology, is emerging as the most promising remediation method for mine tailings by introducing tolerant plant species. It is particularly effective in dealing with large-area mine tailings with shallow contamination of organic, nutrient and metal pollutants. In this review, the background, concepts and applications of phytoremediation are comprehensively discussed. Furthermore, proper amendments used to improve the physical, chemical and biological properties of mine tailings are systematically reviewed and compared. Emphasis is placed on the types and characteristics of tolerant plants and their role in phytoremediation. Moreover, the role of microorganisms and their mechanism in phytoremediation are also discussed in-depth. Copyright © 2017 Elsevier Ltd. All rights reserved.

Using ontology network structure in text mining.

Science.gov (United States)

Berndt, Donald J; McCart, James A; Luther, Stephen L

2010-11-13

Statistical text mining treats documents as bags of words, with a focus on term frequencies within documents and across document collections. Unlike natural language processing (NLP) techniques that rely on an engineered vocabulary or a full-featured ontology, statistical approaches do not make use of domain-specific knowledge. The freedom from biases can be an advantage, but at the cost of ignoring potentially valuable knowledge. The approach proposed here investigates a hybrid strategy based on computing graph measures of term importance over an entire ontology and injecting the measures into the statistical text mining process. As a starting point, we adapt existing search engine algorithms such as PageRank and HITS to determine term importance within an ontology graph. The graph-theoretic approach is evaluated using a smoking data set from the i2b2 National Center for Biomedical Computing, cast as a simple binary classification task for categorizing smoking-related documents, demonstrating consistent improvements in accuracy.

A Global Survey and Interactive Map Suite of Deep Underground Facilities; Examples of Geotechnical and Engineering Capabilities, Achievements, Challenges: (Mines, Shafts, Tunnels, Boreholes, Sites and Underground Facilities for Nuclear Waste and Physics R&D)

Science.gov (United States)

Tynan, M. C.; Russell, G. P.; Perry, F.; Kelley, R.; Champenois, S. T.

2017-12-01

This global survey presents a synthesis of some notable geotechnical and engineering information reflected in four interactive layer maps for selected: 1) deep mines and shafts; 2) existing, considered or planned radioactive waste management deep underground studies, sites, or disposal facilities; 3) deep large diameter boreholes, and 4) physics underground laboratories and facilities from around the world. These data are intended to facilitate user access to basic information and references regarding deep underground "facilities", history, activities, and plans. In general, the interactive maps and database [http://gis.inl.gov/globalsites/] provide each facility's approximate site location, geology, and engineered features (e.g.: access, geometry, depth, diameter, year of operations, groundwater, lithology, host unit name and age, basin; operator, management organization, geographic data, nearby cultural features, other). Although the survey is not all encompassing, it is a comprehensive review of many of the significant existing and historical underground facilities discussed in the literature addressing radioactive waste management and deep mined geologic disposal safety systems. The global survey is intended to support and to inform: 1) interested parties and decision makers; 2) radioactive waste disposal and siting option evaluations, and 3) safety case development as a communication tool applicable to any mined geologic disposal facility as a demonstration of historical and current engineering and geotechnical capabilities available for use in deep underground facility siting, planning, construction, operations and monitoring.

Symposium on the geometrical and geomechanical classification of working coal panels in underground mines. Simposio sobre caracterizacion geometrica y geomecanica de paneles de explotacion de carbon en la mineria subterranea

Energy Technology Data Exchange (ETDEWEB)

1990-01-01

Includes the papers, discussions and conclusions of the above symposium held at the Oviedo School of Mines from 3 to 4 July 1989. The following organisations took part: Spanish Geological/Mining Institute; Ocicarbon; North-West School for Mining Engineers; Higher Council of Schools for Mining Engineers; Department of Mineral Exploration and Mining of the University of Oviedo; and Asturian Council for Industry, Commerce and Tourism.

Development of mechanization of extraction in underground coal mining (part I)

Energy Technology Data Exchange (ETDEWEB)

Strzeminski, J

1984-01-01

The history of underground coal mining and history of mechanizing underground operations of cutting, strata control, mine haulage, hoisting and ventilation are discussed. The following development periods are characterized: until 1769 (date of steam engine invention by J. Watt), from 1769 to 1945 (period of partial mechanization of operations in underground coal mining), from 1945 (period of comprehensive mechanization and automation). A general description of mining in the first development period is given. Evaluation of the second development period concentrates on mechanization in underground coal mining. The following equipment types are described: cutting (pneumatic picks and pneumatic drills, coal saws developed by Eickhoff, coal cutters developed after 1870, cutter loaders patented in 1925-1927, coal plows and coal cutter loaders), mine haulage (mine cars, conveyors developed in the United Kingdom, Germany and Russia, Poland), strata control at working faces (timber props, steel friction props, roof bars), strata control in the goaf (room and pillar mining, stowing, minestone utilization for stowing in Upper Silesia, hydraulic stowing in Upper Silesia). 5 references.

Factors Associated With Healthcare-Acquired Catheter-Associated Urinary Tract Infections: Analysis Using Multiple Data Sources and Data Mining Techniques.

Science.gov (United States)

Park, Jung In; Bliss, Donna Z; Chi, Chih-Lin; Delaney, Connie W; Westra, Bonnie L

The purpose of this study was to identify factors associated with healthcare-acquired catheter-associated urinary tract infections (HA-CAUTIs) using multiple data sources and data mining techniques. Three data sets were integrated for analysis: electronic health record data from a university hospital in the Midwestern United States was combined with staffing and environmental data from the hospital's National Database of Nursing Quality Indicators and a list of patients with HA-CAUTIs. Three data mining techniques were used for identification of factors associated with HA-CAUTI: decision trees, logistic regression, and support vector machines. Fewer total nursing hours per patient-day, lower percentage of direct care RNs with specialty nursing certification, higher percentage of direct care RNs with associate's degree in nursing, and higher percentage of direct care RNs with BSN, MSN, or doctoral degree are associated with HA-CAUTI occurrence. The results also support the association of the following factors with HA-CAUTI identified by previous studies: female gender; older age (>50 years); longer length of stay; severe underlying disease; glucose lab results (>200 mg/dL); longer use of the catheter; and RN staffing. Additional findings from this study demonstrated that the presence of more nurses with specialty nursing certifications can reduce HA-CAUTI occurrence. While there may be valid reasons for leaving in a urinary catheter, findings show that having a catheter in for more than 48 hours contributes to HA-CAUTI occurrence. Finally, the findings suggest that more nursing hours per patient-day are related to better patient outcomes.

Dismantling and ploughing under of the Union 103 underground mine in the Hambach opencast mine; Rueckbau und Ueberbaggerung der Tiefbaugrube Union 103 im Tagebau Hambach

Energy Technology Data Exchange (ETDEWEB)

Hempel, Ralf [RWE Power AG, Sparte Tagebau Bergheim (DE). Abt. Bergtechnik (PCS-B); Houben, Bernd [RWE Power AG, Tagebau Hambach, Niederzier (DE). Abt. Bergbau (BCH-BT)

2012-01-15

As early as the first decades of the past century, Germany as an industrial location strove to achieve a largely independent raw material supply. In this context, a project on underground mining of lignite in the Rhenish lignite mining area - in the region of today's Hambach opencast mine - was launched. The 'Union 103' lignite underground mine near the township of Morschenich was established. Mining work at the Union 103 colliery was confined to the sinking of two shafts down to a depth of 330 m and the construction of roadways with a length of some 11 km. Repeated inflow of water and insufficient profitability led to the closure of the colliery only a few years later in 1955 before the start of regular mining activities. The advancing Hambach opencast mine reached the Union 103 colliery in March 2011. Basic studies were performed to develop a concept for cutting free and dismantling the roadways and shafts. Accompanying exploratory measures to determine the support condition of the mine workings were carried out as well. A report on the current status of the dismantling work and preparatory execution engineering has been provided. (orig.)

An overview of the western Maryland coal combustion by-products/acid mine drainage initiative, Part 1 of 3

International Nuclear Information System (INIS)

Petzrick, P.; Rafalko, L.G.; Lyons, C.

1996-01-01

The western Maryland coal combustion by-products (CCB)/acid mine drainage (AMD) initiative (the Initiative) is a public-private partnership exploring the use of CCBs to eliminate AMD from Maryland's abandoned coal mines. This dynamic partnership will sponsor a series of large scale experiments and demonstrations addressing the engineering problems that characterize the beneficial application of CCBs to prevent acid formation on a scale that is consistent with the large quantity of these materials that will be produced by power plants in or near western Maryland. The initial demonstration is the filling and sealing of a small hand dug mine (the Frazee Mine) under approximately ninety feet of overburden on Winding Ridge near Friendsville, Maryland. A second demonstration is being planned for the Kempton mine complex. Subsequent demonstrations will focus on reducing the cost of materials handling and mine injection and solving the engineering problems characteristic of filling abandoned mines in Maryland. The Initiative is the flagship activity in Maryland's overall Ash Utilization Program, the goal of which is to promote beneficial use of all coal combustion by-products

International Conference on Computational Intelligence in Data Mining

CERN Document Server

Mohapatra, Durga

2017-01-01

The book presents high quality papers presented at the International Conference on Computational Intelligence in Data Mining (ICCIDM 2016) organized by School of Computer Engineering, Kalinga Institute of Industrial Technology (KIIT), Bhubaneswar, Odisha, India during December 10 – 11, 2016. The book disseminates the knowledge about innovative, active research directions in the field of data mining, machine and computational intelligence, along with current issues and applications of related topics. The volume aims to explicate and address the difficulties and challenges that of seamless integration of the two core disciplines of computer science. .

Re-envisioning paediatric nurse training in a re-engineered health care system

Directory of Open Access Journals (Sweden)

Minette Coetzee

2014-10-01

Method: In response to the Committee on Morbidity and Mortality in Children recommendation, a colloquium was convened as a national forum for schools of nursing, departments of health, health care facilities, clinicians and regulatory bodies to advance children’s nursing in South Africa. Objectives: The goals of the colloquium were to thoroughly investigate the situation in South Africa’s paediatric nurse training, plot ways to strengthen and expand postgraduate paediatric programmes to meet priority child health needs, and to build relationships between the various schools and stakeholders. Results: Outcomes included the clarification and strengthening of a ‘stakeholder grid’ in nurse training, recognition of the need for more active teaching and learning strategies in curricula linked to national child health priorities, as well as the need to develop and support clinical nursing practice in facilities.

Human Factors for Nursing: From In-Situ Testing to Mobile Usability Engineering.

Science.gov (United States)

Kushniruk, Andre W; Borycki, Elizabeth M; Solvoll, Terje; Hullin, Carola

2016-01-01

The tutorial goal is to familiarize participants with human aspects of health informatics and human-centered approaches to the design, evaluation and deployment of both usable and safe healthcare information systems. The focus will be on demonstrating and teaching practical and low-cost methods for evaluating mobile applications in nursing. Basic background to testing methods will be provided, followed by live demonstration of the methods. Then the audience will break into small groups to explore the application of the methods to applications of interest (there will be a number of possible applications that will be available for applications in areas such as electronic health records and decision support, however, if the groups have applications of specific interest to them that will be possible). The challenges of conducting usability testing, and in particular mobile usability testing will be discussed along with practical solutions. The target audience includes practicing nurses and nurse researchers, nursing informatics specialists, nursing students, nursing managers and health informatics professionals interested in improving the usability and safety of healthcare applications.

Clinical Immersion and Biomedical Engineering Design Education: "Engineering Grand Rounds".

Science.gov (United States)

Walker, Matthew; Churchwell, André L

2016-03-01

Grand Rounds is a ritual of medical education and inpatient care comprised of presenting the medical problems and treatment of a patient to an audience of physicians, residents, and medical students. Traditionally, the patient would be in attendance for the presentation and would answer questions. Grand Rounds has evolved considerably over the years with most sessions being didactic-rarely having a patient present (although, in some instances, an actor will portray the patient). Other members of the team, such as nurses, nurse practitioners, and biomedical engineers, are not traditionally involved in the formal teaching process. In this study we examine the rapid ideation in a clinical setting to forge a system of cross talk between engineers and physicians as a steady state at the praxis of ideation and implementation.

An Evaluation of Text Mining Tools as Applied to Selected Scientific and Engineering Literature.

Science.gov (United States)

Trybula, Walter J.; Wyllys, Ronald E.

2000-01-01

Addresses an approach to the discovery of scientific knowledge through an examination of data mining and text mining techniques. Presents the results of experiments that investigated knowledge acquisition from a selected set of technical documents by domain experts. (Contains 15 references.) (Author/LRW)

Radon measurements concerning engineering-geological problems in lignite mining

Energy Technology Data Exchange (ETDEWEB)

Heinicke, J

1986-07-01

Radon measurements have been carried out by the aid of solid-state track detectors at the highwall of a lignite mine in order to forecast the eventual course of a landslide. The measured radon distributions and their changes as a function of time indicated that the slope was geodynamically active, but it was not possible to forecast the rate of sliding.

Implementing of action plans for risk communication on the uranium mining sites remedy at Ningyo-toge Environmental Engineering Center (1) (Contract research)

International Nuclear Information System (INIS)

Yabuta, Naohiro; Kawai, Jun; Hikawa, Tamae; Tokizawa, Takayuki; Sato, Kazuhiko; Koga, Osamu

2008-11-01

On the closure of uranium mine site at Ningyo-Toge Environmental Engineering Center Japan Atomic Energy Agency, the action plans for risk communication with residence and local governments were developed and implemented. Under a practical program of the risk communication, an ethnographical research on Ningyo-Toge Environmental Engineering Center has been conducted by local high school students. The research was focused on several social groups such as engineers at the Center and residents around Ningyo-toge and described their circumstances from the past to the present, since the discovery of the uranium outcrop 1955. In addition, it should be noted that as a results, the research project led several effects listed below; 1) High school students understood significance of the uranium development projects implemented at Ningyo-toge, 2) Differences of standpoints between local residents and Ningyo-toge became clearer, 3) Foundation to communicate between local communities and Ningyo-toge was found out, and 4) The educational program on an ethnographical research was conducted autonomously by local high school students. (author)

Enhancing Nursing Education with Remote Access Laboratories

Directory of Open Access Journals (Sweden)

Leslie Alan Bowtell

2012-12-01

Full Text Available Abstract—Given the vast coverage area and dispersed population centres in which nursing professionals practice in Australia, Remote Access Laboratory (RAL based learning activities would seem to be an ideal match. However while they are commonplace in engineering faculties; in other disciplines such activities are not widely used. This may well be due to the intricacies of these practicals not being as straightforward and readily reproducible as typical physics or science experiments. In our chosen case, the safe practice of intravenous pump driver operations and related clinical reasoning skills are important components for the training of both registered nurses and nursing students. The aim of this research project is to develop and trial remote access technologies that enable nursing students to test their knowledge, skills, and clinical reasoning with intravenous infusion pump drivers. This has been possible by extending the concept of RAL from a physical and tangible experiment, to more conceptual experimentation in any form conducted remotely. In such a context clinical reasoning becomes possible. This paper discusses a prototype system that has been built with collaborative input from the Faculty of Engineering and Surveying and the Department of Nursing and Midwifery. An initial evaluation with a group of nursing students has been completed to assess if such activities can assist with the training of student nurses. Previous work has identified the need to scaffold learning activities that rely on RAL technology; the key conclusion in this paper is that in the context of nursing this has to be taken a step further. RAL activities here require contextualisation to become an effective learning tool.

Risk Analysis and Prediction of Floor Failure Mechanisms at Longwall Face in Parvadeh-I Coal Mine using Rock Engineering System (RES)

Science.gov (United States)

Aghababaei, Sajjad; Saeedi, Gholamreza; Jalalifar, Hossein

2016-05-01

The floor failure at longwall face decreases productivity and safety, increases operation costs, and causes other serious problems. In Parvadeh-I coal mine, the timber is used to prevent the puncture of powered support base into the floor. In this paper, a rock engineering system (RES)-based model is presented to evaluate the risk of floor failure mechanisms at the longwall face of E 2 and W 1 panels. The presented model is used to determine the most probable floor failure mechanism, effective factors, damaged regions and remedial actions. From the analyzed results, it is found that soft floor failure is dominant in the floor failure mechanism at Parvadeh-I coal mine. The average of vulnerability index (VI) for soft, buckling and compressive floor failure mechanisms was estimated equal to 52, 43 and 30 for both panels, respectively. By determining the critical VI for soft floor failure mechanism equal to 54, the percentage of regions with VIs beyond the critical VI in E 2 and W 1 panels is equal to 65.5 and 30, respectively. The percentage of damaged regions showed that the excess amount of used timber to prevent the puncture of weak floor below the powered support base is equal to 4,180,739 kg. RES outputs and analyzed results showed that setting and yielding load of powered supports, length of face, existent water at face, geometry of powered supports, changing the cutting pattern at longwall face and limiting the panels to damaged regions with supercritical VIs could be considered to control the soft floor failure in this mine. The results of this research could be used as a useful tool to identify the damaged regions prior to mining operation at longwall panel for the same conditions.

Overcoming soil compaction in surface mine reclamation

Energy Technology Data Exchange (ETDEWEB)

Sweigard, R.J. (University of Kentucky, Lexington, KY (USA). Dept. of Mining Engineering)

1991-01-01

Rubber-tyred soil reconstruction equipment causes compaction of soil and means surface mine operators cannot satisfy crop yield standards defined by the Surface Mining Control and Reclamation Act. Soil compaction can be overcome by either modifying the reconstruction process or alleviating the problem, for example by deep tillage, once it occurs. The Dept. of Mining Engineering at the Institute of Mining and Minerals Research is conducting a laboratory investigation into a method of injecting low density porous organic material into a bin containing soil at the same time as the soil is ripped. This should prevent voids collapsing when subjected to forces from farm equipment and natural sources. Soil analyses are performed before and after the injection. Ripping and injection with ground pecan shells had a residual effect on nuclear bulk density compared to the initially compacted case and also showed an improvement in hydraulic conductivity. Work is in progress on modifying the system to handle other injection material and should lead on to field tests on a prototype involving both soil analysis and crop yield determination. 1 fig.

Overcoming soil compaction in surface mine reclamation

International Nuclear Information System (INIS)

Sweigard, R.J.

1991-01-01

Rubber-tyred soil reconstruction equipment causes compaction of soil and means surface mine operators cannot satisfy crop yield standards defined by the Surface Mining Control and Reclamation Act. Soil compaction can be overcome by either modifying the reconstruction process or alleviating the problem, for example by deep tillage, once it occurs. The Dept. of Mining Engineering at the Institute of Mining and Minerals Research is conducting a laboratory investigation into a method of injecting low density porous organic material into a bin containing soil at the same time as the soil is ripped. This should prevent voids collapsing when subjected to forces from farm equipment and natural sources. Soil analyses are performed before and after the injection. Ripping and injection with ground pecan shells had a residual effect on nuclear bulk density compared to the initially compacted case and also showed an improvement in hydraulic conductivity. Work is in progress on modifying the system to handle other injection material and should lead on to field tests on a prototype involving both soil analysis and crop yield determination. 1 fig

A study of trends in occupational risks associated with coal mining

International Nuclear Information System (INIS)

Amoudru, C.

1980-01-01

The coal industry is well known as a major source of specific types of risk and harmful effects including, for instance, harm to the environment, pollution from various surface installations and hazards associated with the actual task of mining. We shall confine our attention to the third group and discuss only the occupational risks facing miners and ex-miners. Unlike the nuclear and oil industries, coal-mines employ very large work-forces, and the risks associated with mining therefore have a considerable impact. Mining is also a highly integrated industry: a mine's own work-force carries out all the underground engineering work (preparatory excavations, installation work, etc.) as well as maintenance. In this narrow field, a distinction should immediately be drawn between two main areas: industrial accidents; and occupational diseases, which include silicosis or, more precisely, coal-miner's pneumoconiosis

Mine Water Treatment in Hongai Coal Mines

Science.gov (United States)

Dang, Phuong Thao; Dang, Vu Chi

2018-03-01

Acid mine drainage (AMD) is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine drainage treatment in Hongai coal mines. In addition, selection and criteria for the design of the treatment systems have been presented.

Mine Water Treatment in Hongai Coal Mines

OpenAIRE

Dang Phuong Thao; Dang Vu Chi

2018-01-01

Acid mine drainage (AMD) is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine ...

Vlsi implementation of flexible architecture for decision tree classification in data mining

Science.gov (United States)

Sharma, K. Venkatesh; Shewandagn, Behailu; Bhukya, Shankar Nayak

2017-07-01

The Data mining algorithms have become vital to researchers in science, engineering, medicine, business, search and security domains. In recent years, there has been a terrific raise in the size of the data being collected and analyzed. Classification is the main difficulty faced in data mining. In a number of the solutions developed for this problem, most accepted one is Decision Tree Classification (DTC) that gives high precision while handling very large amount of data. This paper presents VLSI implementation of flexible architecture for Decision Tree classification in data mining using c4.5 algorithm.

The Necessity of Public Relations for Sustainable Mining Activities

Science.gov (United States)

Lee, Hyunbock; Ji, Sangwoo

2015-04-01

other hand, in the survey to determine what the greatest difficulties of the current mining activities, 54% of mining companies chose environmental regulations, 26% of mining companies chose conflicts between mine area residents and mining companies. Environmental regulations are may defined as the greatest difficulty of current mining activities. But most of environmental regulation's problems are caused by frictions with residents, because all of South Korean mines are very close to villages. So, the biggest difficulty of mining activities can be defined conflicts between residents and mining companies. Moreover, general people in South Korea including some mining engineers recognize the mining industry as a declined and pollution industry. Without clear understanding of mining activities, any mine developments and policies related to mining activities cannot be made by rational discussions. And, if their recognition is not formed in a rational way, it will be turned to extreme fear or blind hatred. Therefore, to understand mining activities correctly, the effective public relations strategy is necessary such as corporate advertisements or public advertisements.

Mine Water Treatment in Hongai Coal Mines

Directory of Open Access Journals (Sweden)

Dang Phuong Thao

2018-01-01

Full Text Available Acid mine drainage (AMD is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine drainage treatment in Hongai coal mines. In addition, selection and criteria for the design of the treatment systems have been presented.

Removal method of radium in mine water by filter sand

International Nuclear Information System (INIS)

Taki, Tomihiro; Naganuma, Masaki

2003-01-01

Trace radium is contained in mine water from the old mine road in Ningyo-Toge Environmental Engineering Center, JNC. We observed that filter sand with hydrated manganese oxide adsorbed radium in the mine water safely for long time. The removal method of radium by filter sand cladding with hydrated manganese oxide was studied. The results showed that radium was removed continuously and last for a long time from mine water with sodium hypochlorite solution by passing through the filter sand cladding with hydrated manganese. Only sodium hypochlorite solution was used. When excess of it was added, residue chlorine was used as chlorine disinfection. Filter sand cladding with hydrated manganese on the market can remove radium in the mine water. The removal efficiency of radium is the same as the radium coprecipitation method added with barium chloride. The cost is much lower than the ordinary methods. Amount of waste decreased to about 1/20 of the coprecipitation method. (S.Y.)

The importance of mines for ultimate storage at Deilmann-Haniel Shaft Sinking

International Nuclear Information System (INIS)

Greinacher, Jochen; Oellers, Thomas; Ahlbrecht, Thomas

2011-01-01

Deilmann-Haniel Shaft Sinking GmbH and its predecessor and associate companies have been involved in projects for underground ultimate storage in Germany, Europe and America for over 45 years. The field of activities previously comprised surveying, planning and sinking of shafts, repair and conversion work, design of underground sealing structures, planning of conveyors and support of the BfS in planning approval procedures. Following discontinuation of activities in the German coal mining industry the use of mines for ultimate storage is an important support for German specialist mining companies. The use of mines for ultimate storage ensures that the existing mining know how in Germany is maintained, because training of the younger generation on the commercial and engineering side of the companies is made possible by the imminent major projects.

Henderson Deep Underground Science and Engineering Lab: Unearthing the secrets of the Universe, underground

International Nuclear Information System (INIS)

Jung, C.K.

2011-01-01

The Henderson Mine near Empire, Colorado is proposed to be the site to host a Deep Underground Science and Engineering Laboratory (DUSEL), which will have a rich program for forefront research in physics, biology, geosciences, and mining engineering. The mine is owned by the Climax Molybdenum Company (CMC). It is located about 50 miles west of Denver and is easily accessible via major highways. The mine is modern and has extensive infrastructure with reserve capacity well-suited to the demands of DUSEL. CMC owns all land required for DUSEL, including the tailings site. It also has all environmental and mining permits required for DUSEL excavation, core drilling, and rock disposal. The mine owners are enthusiastic supporters of this initiative. In support of the Henderson DUSEL project, the State of Colorado has pledged substantial funding for surface construction.

SIMPL: A Simplified Model-Based Program for the Analysis and Visualization of Groundwater Rebound in Abandoned Mines to Prevent Contamination of Water and Soils by Acid Mine Drainage

Directory of Open Access Journals (Sweden)

Sung-Min Kim

2018-05-01

Full Text Available Cessation of dewatering following underground mine closure typically results in groundwater rebound, because mine voids and surrounding strata undergo flooding up to the levels of the decant points, such as shafts and drifts. SIMPL (Simplified groundwater program In Mine workings using the Pipe equation and Lumped parameter model, a simplified lumped parameter model-based program for predicting groundwater levels in abandoned mines, is presented herein. The program comprises a simulation engine module, 3D visualization module, and graphical user interface, which aids data processing, analysis, and visualization of results. The 3D viewer facilitates effective visualization of the predicted groundwater level rebound phenomenon together with a topographic map, mine drift, goaf, and geological properties from borehole data. SIMPL is applied to data from the Dongwon coal mine and Dalsung copper mine in Korea, with strong similarities in simulated and observed results. By considering mine workings and interpond connections, SIMPL can thus be used to effectively analyze and visualize groundwater rebound. In addition, the predictions by SIMPL can be utilized to prevent the surrounding environment (water and soil from being polluted by acid mine drainage.

Fiscal 1997 technological survey report. Engineer exchange project - coal mine technological field (Advanced coal producing country survey - U.S.A. survey); 1997 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) senshin santankoku chosa. Beikoku chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

While the introduction and adaptation of the Longwall excavation technology were carried forward for coal producing countries in the Pacific region, U.S.A. information was collected by making tours of coal mines in the West and Washington/Colorado/Utah States, with the intention of ascertaining technological trend so as to carry out efficient technological transfer, and for the purpose of replenishing the contents and contributing to the smooth implementation of the engineer exchange project in 'coal mine technological field'. The coal reserves are 400 billion tons, with 840 million tons produced and with 80 million tons exported; not less than 56% of the U.S. domestic electricity rests on coal. Production by open-pit mining is the majority while the output by underground mining is 38%; the Longwall method has increased as a digging method, taking 18% of all digging output. The productivity is 4.24 ton/person per day and ranks as the world highest. The coal mining technological trend in the U.S. can be summarized as follows. The coal mining output in the West is increasing, with the number of mines decreasing, so that the output per mine is increasing. With the output ratio by open-pit mining increasing, the digging method in the mine is being changed to the Longwall. (NEDO)

Draft of a Federal Mining Law (BBergG). [German Federal Republic

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

Standardization and rearrangement is proposed for all the mining laws in the Federal Republic of Germany, especially of the regulations concerning prospecting and mining of natural resources. The draft provides; 1) creation of a modern, elastic system of concessions for particularly important natural resources withdrawn from the landed property; smoothing of the existing system of mineral rights; 2) development of the instruments of mining law adapted to the special requirements of mining natural resources in view of preventive and current control of the operation and its supervision; 3) first-time authorizations for federal safety and labor protection decrees; 4) reformation of the relationship with the employer's liability insurances and, resulting therefrom, improvement of the accident prevention measures; 5) stronger embodiment of damage-preventing measures in mining-damage law; improvement of the extent of liability and the protection of those damaged; 6) accounting for related new engineering developments (underground tankless storage); 7) final regulation for prospecting and mining of natural resources in the range of the continental shelf; 8) relief of mining law from alien legal matters as well as liquidation of antiquated institutes of mining law.

Rock engineering applications, 1991

International Nuclear Information System (INIS)

Franklin, J.A.; Dusseault, M.B.

1991-01-01

This book demonstrates how to apply the theories and principles of rock engineering to actual engineering and construction tasks. It features insights on geology for mining and tunnelling applications. It is practical resource that focuses on the latest technological innovation and examines up-to-date procedures used by engineers for coping with complex rock conditions. The authors also discuss question related to underground space, from design approaches to underground housing and storage. And they cover the monitoring of storage caverns for liquid and gaseous products or toxic and radioactive wastes

Lunabotics Mining: Evolution of ARTEMIS PRIME

Science.gov (United States)

Bertke, Sarah; Gries, Christine; Huff, Amanda; Logan, Brittany; Oliver, Kaitlin; Rigney, Erica; Tyree, Whitney; Young, Maegan

2010-01-01

This slide presentation reviews the development of Amassing Regolith with Topper Engineers eMploying Innovative Solutions (ARTEMIS) in a competition to develop robotic lunar mining capabilities. The goal of the competition was to design, build and operate a remotely controlled device that is capable of excavating, transporting and discharging lunar regolith simulant in a lunar environment over a 13 minute period.

Model Validation and Verification of Data Mining from the ...

African Journals Online (AJOL)

Michael Horsfall

In this paper, we seek to present a hybrid method for Model Validation and Verification of Data Mining from the ... This model generally states the numerical value of knowledge .... procedures found in the field of software engineering should be ...

Possibility of Integrated Data Mining of Clinical Data

Directory of Open Access Journals (Sweden)

Akinori Abe

2007-03-01

Full Text Available In this paper, we introduce integrated data mining. Because of recent rapid progress in medical science as well as clinical diagnosis and treatment, integrated and cooperative research among medical researchers, biology, engineering, cultural science, and sociology is required. Therefore, we propose a framework called Cyber Integrated Medical Infrastructure (CIMI. Within this framework, we can deal with various types of data and consequently need to integrate those data prior to analysis. In this study, for medical science, we analyze the features and relationships among various types of data and show the possibility of integrated data mining.

Business approach to mine air quality and ventilation

Energy Technology Data Exchange (ETDEWEB)

Byrne, M.J. [Newmont Mining Corp., Greenwood Village, CO (United States)

2009-07-01

A business approach to air quality and ventilation in mines was discussed in this presentation. Issues that were addressed included leadership approaches in bridging the gap between the visible culture of policies and procedures with invisible cultures such as norms, assumptions and beliefs. An overview of occupational safety was also presented in terms of measuring diesel particulate matter (DPM) and key DPM activities such as ventilation modeling; remote control of ventilation circuits; real-time diagnostics of engine performance through electronic control modules; personnel and equipment tracking systems; remote carbon monoxide and carbon dioxide monitoring; and semi-quantitative real-time DPM monitoring. Resources such as ventilation engineers and other professionals also contribute to key DPM activities as do experience and good practice sharing between sites. The purpose of the presentation was to determine if 160 {mu}g/m{sup 3} is an achievable number for exposure to DPM and the standard by which mines should operate globally. figs.

Fiscal 1998 engineer interexchange project (coal mine technology field). International interexchange project (Workshop in Japan); 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya). Kokusai koryu jigyo (kokunai workshop)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the workshop and technical tour held in Japan for technical interexchange of domestic and overseas engineers. From the information obtained, the higher productivity of coal mines is dependent on selective mining under blessed geological conditions, however, basically establishment of an advanced management technique for inexpensive stable operation. Both preliminary collection of geological information and introduction of advanced facilities even under unstable conditions are necessary. The balance and optimization of the whole system, and an excellent human nature for operation are also essential. Use of roof bolt supports is diffusing as improvement technology of excavation speed and roof control technology over the world. However, for introduction of new technologies, collection of test results and various kinds of training are necessary. Methane gas in coal seams as the main theme of the Hokkaido workshop is a precious unused natural resource, and important for prevention of global warming and coal mine protection measures. Its use is dependent on development of gas drainage technology. (NEDO)

Ground standoff mine detection system (GSTAMIDS) engineering, manufacturing, and development (EMD) Block 0

Science.gov (United States)

Pressley, Jackson R.; Pabst, Donald; Sower, Gary D.; Nee, Larry; Green, Brian; Howard, Peter

2001-10-01

The United States Army has contracted EG&G Technical Services to build the GSTAMIDS EMD Block 0. This system autonomously detects and marks buried anti-tank land mines from an unmanned vehicle. It consists of a remotely operated host vehicle, standard teleoperation system (STS) control, mine detection system (MDS) and a control vehicle. Two complete systems are being fabricated, along with a third MDS. The host vehicle for Block 0 is the South African Meerkat that has overpass capability for anti-tank mines, as well as armor anti-mine blast protection and ballistic protection. It is operated via the STS radio link from within the control vehicle. The Main Computer System (MCS), located in the control vehicle, receives sensor data from the MDS via a high speed radio link, processes and fuses the data to make a decision of a mine detection, and sends the information back to the host vehicle for a mark to be placed on the mine location. The MCS also has the capability to interface into the FBCB2 system via SINGARS radio. The GSTAMIDS operator station and the control vehicle communications system also connect to the MCS. The MDS sensors are mounted on the host vehicle and include Ground Penetrating Radar (GPR), Pulsed Magnetic Induction (PMI) metal detector, and (as an option) long-wave infrared (LWIR). A distributed processing architecture is used so that pre-processing is performed on data at the sensor level before transmission to the MCS, minimizing required throughput. Nine (9) channels each of GPR and PMI are mounted underneath the meerkat to provide a three-meter detection swath. Two IR cameras are mounted on the upper sides of the Meerkat, providing a field of view of the required swath with overlap underneath the vehicle. Also included on the host vehicle are an Internal Navigation System (INS), Global Positioning System (GPS), and radio communications for remote control and data transmission. The GSTAMIDS Block 0 is designed as a modular, expandable system

Integrated system of production information processing for surface mines

Energy Technology Data Exchange (ETDEWEB)

Li, K.; Wang, S.; Zeng, Z.; Wei, J.; Ren, Z. [China University of Mining and Technology, Xuzhou (China). Dept of Mining Engineering

2000-09-01

Based on the concept of geological statistic, mathematical program, condition simulation, system engineering, and the features and duties of each main department in surface mine production, an integrated system for surface mine production information was studied systematically and developed by using the technology of data warehousing, CAD, object-oriented and system integration, which leads to the systematizing and automating of the information management, data processing, optimization computing and plotting. In this paper, its overall object, system design, structure and functions and some key techniques were described. 2 refs., 3 figs.

Women’s well-being and reproductive health in Indian mining community: need for empowerment

Science.gov (United States)

2013-01-01

This paper is a qualitative study of women’s well-being and reproductive health status among married women in mining communities in India. An exploratory qualitative research design was conducted using purposive sampling among 40 selected married women in a rural Indian mining community. Ethical permission was obtained from Goa University. A semi-structured indepth interview guide was used to gather women’s experiences and perceptions regarding well-being and reproductive health in 2010. These interviews were audiotaped, transcribed, verified, coded and then analyzed using qualitative content analysis. Early marriage, increased fertility, less birth intervals, son preference and lack of decision-making regarding reproductive health choices were found to affect women’s reproductive health. Domestic violence, gender preference, husbands drinking behaviors, and low spousal communication were common experiences considered by women as factors leading to poor quality of marital relationship. Four main themes in confronting women’s well-being are poor literacy and mobility, low employment and income generating opportunities, poor reproductive health choices and preferences and poor quality of martial relationships and communication. These determinants of physical, psychological and cultural well-being should be an essential part of nursing assessment in the primary care settings for informed actions. Nursing interventions should be directed towards participatory approach, informed decision making and empowering women towards better health and well-being in the mining community. PMID:23602071

4th International conference on Knowledge Discovery and Data Mining

CERN Document Server

Knowledge Discovery and Data Mining

2012-01-01

The volume includes a set of selected papers extended and revised from the 4th International conference on Knowledge Discovery and Data Mining, March 1-2, 2011, Macau, Chin.   This Volume is to provide a forum for researchers, educators, engineers, and government officials involved in the general areas of knowledge discovery and data mining and learning to disseminate their latest research results and exchange views on the future research directions of these fields. 108 high-quality papers are included in the volume.

Reuse of coal mining wastes in civil engineering. Part 2: Utilization of minestone

International Nuclear Information System (INIS)

Skarzynska, K.M.

1995-01-01

The oldest method of minestone utilization is reclamation of spoil heaps by adapting them to the landscape by afforestation or agricultural management. The best method is, however, complete removal of the wastes. Hence, for many years research has been carried out to find new ways of minestone utilization to minimize disposal cost and harmful environmental effects. Earth structures offer the best possibilities of minestone utilization. Investigations conducted in recent years in Germany, the United Kingdom, France, Belgium, the Netherlands and also in Poland have led to the use of many tones of wastes in the construction of road and railroad banks, river embankments, dykes and dams, filling of land depressions and open pits, as well as for sea wharfs and land reclamation. This paper presents descriptions of minestone applications to hydraulic, harbor and road engineering as well as to mine backfilling and restoration of derelict land. Effective management of minestone is still the principal problem with respect to safety, economics and environmental protection. Hence, the propagation of minestone utilization of known sources and the search for new methods of its management are essential. Two sections in this review have been devoted to the prevention of spontaneous heating and combustion of minestone and to the impact of minestone structures on the environment and its protection

Aquatic Ecosystem Enhancement at Mountaintop Mining Sites Symposium

Energy Technology Data Exchange (ETDEWEB)

Black, D. Courtney; Lawson, Peter; Morgan, John; Maggard, Randy; Schor, Horst; Powell, Rocky; Kirk, Ed. J.

2000-01-12

Welcome to this symposium which is part of the ongoing effort to prepare an Environmental Impact Statement (EIS) regarding mountaintop mining and valley fills. The EIS is being prepared by the U.S. Environmental Protection Agency, U.S. Army Corps of Engineers, U.S. Office of Surface Mining, and U.S. Fish and Wildlife Service, in cooperation with the State of West Virginia. Aquatic Ecosystem Enhancement (AEE) at mountaintop mining sites is one of fourteen technical areas identified for study by the EIS Interagency Steering Committee. Three goals were identified in the AEE Work Plan: 1. Assess mining and reclamation practices to show how mining operations might be carried out in a way that minimizes adverse impacts to streams and other environmental resources and to local communities. Clarify economic and technical constraints and benefits. 2. Help citizens clarify choices by showing whether there are affordable ways to enhance existing mining, reclamation, mitigation processes and/or procedures. 3. Ide identify data needed to improve environmental evaluation and design of mining projects to protect the environment. Today’s symposium was proposed in the AEE Team Work Plans but coordinated planning for the event began September 15, 1999 when representatives from coal industry, environmental groups and government regulators met in Morgantown. The meeting participants worked with a facilitator from the Canaan Valley Institute to outline plans for the symposium. Several teams were formed to carry out the plans we outlined in the meeting.

Erosional stability of rehabilitated uranium mine structures incorporating natural landform characteristics, northern tropical Australia

International Nuclear Information System (INIS)

East, T.J.; Uren, C.J.; Noller, B.N.; Cull, R.F.; Curley, P.M.; Unger, C.J.

1994-01-01

Australian Government guidelines specify that tailings containment structures at rehabilitated uranium mines in the Alligator Rivers Region of tropical northern Australia should have an engineered structural life of 1000 years. As part of the containment structure design process, erosion plots incorporating both regional geomorphological characteristics (concave hillslope profiles and a weathering-resistant rock cover of schist) and more conventional engineering design parameters (straight slopes and mine waste rock) were constructed at the Ranger Uranium Mine. The plots were monitored for storm runoff, and concentrations of solutes, suspended solids and selected ions over successive wet seasons. The concave slopes (the hillslope analogues) had lower peak discharges and lower concentrations of suspended solids than the straight slopes. However, solute concentrations in runoff from the schist covered (hillslope) slopes were higher than from the waste rock covered plots. Solute (mainly magnesium sulfate) concentrations for both rock types decreased by about an order of magnitude over the wet season. High sulfate concentrations are also likely to decrease substantially after several wet seasons, due to settlement of the waste rock and a reduction in rates of weathering. Development of a vegetation cover on the rehabilitated landforms will reduce the high suspended sediment concentrations. These initial results suggest that rehabilitated uranium mine structures which utilise selected features of stable natural landforms in their design may have greater erosional stability than more conventionally engineered structures. (orig.)

Using software to predict occupational hearing loss in the mining industry.

Science.gov (United States)

Azman, A S; Li, M; Thompson, J K

2016-01-01

Powerful mining systems typically generate high-level noise that can damage the hearing ability of miners. Engineering noise controls are the most desirable and effective control for overexposure to noise. However, the effects of these noise controls on the actual hearing status of workers are not easily measured. A tool that can provide guidance in assigning workers to jobs based on the noise levels to which they will be exposed is highly desirable. Therefore, the Pittsburgh Mining Research Division (PMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) developed a tool to estimate in a systematic way the hearing loss due to occupational noise exposure and to evaluate the effectiveness of developed engineering controls. This computer program is based on the ISO 1999 standard and can be used to estimate the loss of hearing ability caused by occupational noise exposures. In this paper, the functionalities of this software are discussed and several case studies related to mining machinery are presented to demonstrate the functionalities of this software.

Applying artificial intelligence technology to support decision-making in nursing: A case study in Taiwan.

Science.gov (United States)

Liao, Pei-Hung; Hsu, Pei-Ti; Chu, William; Chu, Woei-Chyn

2015-06-01

This study applied artificial intelligence to help nurses address problems and receive instructions through information technology. Nurses make diagnoses according to professional knowledge, clinical experience, and even instinct. Without comprehensive knowledge and thinking, diagnostic accuracy can be compromised and decisions may be delayed. We used a back-propagation neural network and other tools for data mining and statistical analysis. We further compared the prediction accuracy of the previous methods with an adaptive-network-based fuzzy inference system and the back-propagation neural network, identifying differences in the questions and in nurse satisfaction levels before and after using the nursing information system. This study investigated the use of artificial intelligence to generate nursing diagnoses. The percentage of agreement between diagnoses suggested by the information system and those made by nurses was as much as 87 percent. When patients are hospitalized, we can calculate the probability of various nursing diagnoses based on certain characteristics. © The Author(s) 2013.

The use of earth observation and decision support systems for the restoration of open-cast nickel mines in Evia, central Greece

NARCIS (Netherlands)

Ganas, A.; Aerts, J.C.J.H.; Astaras, T.; de Vente, J.; Frogoudakis, E.; Labrinos, N.

2004-01-01

We have developed a decision support system (DSS) for open mining areas which reflects and simulates the major decision steps of a mining expert (engineer, manager) during the formulation of a restoration plan. The software supports the mining expert to structure the various restoration alternatives

Atlas Career Path Guidebook: Patterns and Common Practices in Systems Engineers’ Development

Science.gov (United States)

2018-01-16

text mining principles to be used by systems...statistical and text mining principles facilitate the identification of patterns. Figure 1. Helix methodology for career path analysis In order to...illustrate how text mining algorithms might be used to identify similarities in position titles for systems engineers. In broad

Investigation of a Novel Coaxial Power-Split Hybrid Powertrain for Mining Trucks

Directory of Open Access Journals (Sweden)

Weiwei Yang

2018-01-01

Full Text Available Due to the different working conditions and specification requirements of mining trucks when compared to commercial passenger vehicles, better fuel efficiency of mining trucks could lead to more significant economic benefits. Therefore, investigating a hybrid transmission system becomes essential. A coaxial power-split hybrid powertrain system for mining trucks is presented in this paper. The system is characterized as comprising an engine, a generator (MG1, a motor (MC2, two sets of planetary gears, and a clutch (CL1. There are six primary operation modes for the hybrid system including the electric motor mode, the engine mode, the hybrid electric mode, the hybrid and assist mode, the regenerative mode, and the stationary charging mode. The mathematical model of the coaxial power-split hybrid system is established according to the requirements of vehicle dynamic performance and fuel economy performance in a given driving cycle. A hybrid vehicle model based on a rule-based control strategy is established to evaluate the fuel economy. Compared with the Toyota Hybrid System (THS and the conventional mechanical vehicle system using a diesel engine, the simulation results based on an enterprise project indicate that the proposed hybrid system can enhance the vehicle’s fuel economy by 8.21% and 22.45%, respectively, during the given mining driving cycle. The simulation results can be used as a reference to study the feasibility of the proposed coaxial hybrid system whose full potential needs to be further investigated by adopting non-causal control strategies.

Principles and practices of social entrepreneurship for nursing.

Science.gov (United States)

Gilmartin, Mattia J

2013-11-01

Although social justice and action for change are among the nursing profession's core values, curricular content on social entrepreneurship for nurses is not as well developed as it is in the educational programs for students in business, engineering, or public policy. This article describes an undergraduate honors elective course in social entrepreneurship offered at New York University College of Nursing. The course uses a seminar format and incorporates content from the humanities, business, and service-learning, with the goal of promoting participants' understanding of the sources of inequality in the United States and providing the requisite skills to promote effective nursing action for social change. Copyright 2013, SLACK Incorporated.

Trends spanning 36 years of nursing research

OpenAIRE

LEE Hyeyong; SHIMOTAKAHARA Rie; FUKADA Akimi; SHINBASHI Sumiko

2018-01-01

PURPOSE: The aim of demonstrating priorities for future research, this study draws on the strengths of text-mining analysis to analyze trends in nursing research in Japan over a 36-year period. METHODS: Documents published in the online version of the Igaku Chuo Zasshi (ICHUSHI) between 1980 and December 2015 were targeted for analysis. Tendencies and trends over time characterizing words used in the titles of all target research papers were analyzed, along with characteristic words. RESULTS:...

Mine subsidence event at Washington West Apartments

International Nuclear Information System (INIS)

Wilson, D.B.; Weber, M.W.; Purdy, J.; Acker, P.

1994-01-01

A major mine subsidence event occurred in Scranton, PA in early 1993. The initial damage included breakage of gas and water lines, cracking of pavements and sidewalks, and architectural damage to the seven-story apartment building that houses about 150 elderly persons. Visible damage include a 3/4-in dilation of the expansion joint separating the building, approximately 200 interior and exterior cracks, and distress to utility lines. The Office of Surface mining Reclamation and Enforcement (OSM) funded an integrated geotechnical and structural engineering investigation to determine the cause of the subsidence, the limits of affected areas, and the nature of damage to the building. Work included interior surveys, exterior surveys, installation of crack gages, eight subsurface borings, review of building design drawings, review of geologic and mining data, and structural analysis of the rigid steel frame building. The surveys showed the building had undergone movements consisting of a lateral translation, a longitudinal differential settlement, and a transverse differential settlement. Preliminary structural analyses showed that the differential settlements had introduced significant additional stresses in some of the building columns. This paper provides a case history of the cause and effects of the subsidence event. The techniques used to collect and analyze the data are presented along with the findings of the geotechnical and structural engineering investigations. The paper also describes emergency actions that were implemented, the remedial alternatives that were considered, and the method selected as the recommended alternative

Sustainable Mining Environment: Technical Review of Post-mining Plans

Directory of Open Access Journals (Sweden)

Restu Juniah

2017-12-01

Full Text Available The mining industry exists because humans need mining commodities to meet their daily needs such as motor vehicles, mobile phones, electronic equipment and others. Mining commodities as mentioned in Government Regulation No. 23 of 2010 on Implementation of Mineral and Coal Mining Business Activities are radioactive minerals, metal minerals, nonmetallic minerals, rocks and coal. Mineral and coal mining is conducted to obtain the mining commodities through production operations. Mining and coal mining companies have an obligation to ensure that the mining environment in particular after the post production operation or post mining continues. The survey research aims to examine technically the post-mining plan in coal mining of PT Samantaka Batubara in Indragiri Hulu Regency of Riau Province towards the sustainability of the mining environment. The results indicate that the post-mining plan of PT Samantaka Batubara has met the technical aspects required in post mining planning for a sustainable mining environment. Postponement of post-mining land of PT Samantaka Batubara for garden and forest zone. The results of this study are expected to be useful and can be used by stakeholders, academics, researchers, practitioners and associations of mining, and the environment.

[Joint contractures in nursing textbooks].

Science.gov (United States)

Bartoszek, G; Meyer, G; Thiesemann, R

2014-01-01

The transparency criteria of the German statutory health insurance on joint contracture prevention have led to controversies about the appropriate assessment, prevention and treatment as well as to various actions in nursing practice. However, appropriate nursing assessments and proven treatment options are lacking so far. It is unclear whether textbooks on nursing reflect these uncertainties. Search for textbooks on nursing through internet-based search engines and publisher registers, data extraction by one investigator and control by a second. A total of 35 textbooks with contributions on joint contractures were identified of which 25 included a definition, causes/risk factors are presented in 32 textbooks and assessments are presented in 5 books. Most often positioning into a physiological or functional neutral position and passive moving of limbs are recommended as passive prophylaxis. Recommended therapeutic and preventive options do not differ. None of the textbooks reflect that there is a lack of scientific knowledge on the subject. Textbooks on nursing do not deal with complete and scientific sound information on joint contractures.

Numerical simulation of roadway support in a sandstone-type uranium mine

International Nuclear Information System (INIS)

Liu Huipeng; Li Yu; Song Lixia

2009-01-01

At present, the most surrounding rocks of sandstone-type uranium mines in China are mudstone, sandstone, pelitic siltstone, and so on. They show the characteristics of soft rock. Such uranium deposit is not fit for in-situ leaching. If the uranium ores are mined by conventional mining method, one of the problems to be solved is the support technique in the soft rock roadway. So, taking a uranium mine in Inner Mongolia as the research object, the support technique in the soft rock roadway of the sandstone-type uranium deposits is studied. Through on-site engineering geological investigation and laboratory test, the main reasons for roadway damage are analyzed. A technique of support in the soft rock roadway of sandstone-type uranium deposits is put forward by drawing on the expericnce of soft rock roadway support in coal mines. The roadway shape and support parameters are optimized by using a numerical simulation method. The results verified the feasibility of the supporting technique. (authors)

Are women the next driving force in mining?

Energy Technology Data Exchange (ETDEWEB)

Perry, J.

2007-07-15

A symposium entitled 'Women in mining' was held as part of Australia's Minerals Week 2007, on 29 May in Canberra, ACT. In July 2007, Engineers Australia together with Association of Professional Engineers Scientists and Managers, Australia held a women's conference in Melbourne. A survey carried out identified the two main obstacles to women's career advancement: balancing work and life, followed by workplace culture. The majority of female respondents of a recent survey by the Australian Institute of Mining and Metallurgy were concentrated around the early to intermediate stages of their career whereas male respondents were clustered around senior positions. These findings are in line with a report commissioned by the mineral industry and the federal government 'Unearthing new resources: attracting and retaining women in the Australian mineral industry', released in May. This found that the age profile of women in the industry is concentrated towards those aged 34 and under. Lack of child care was cited as the major reason for leaving the industry. A lack of mentor relationships and support networks for women was identified. The article reports comments by Nicole Hollows, Macarthur Coal's CEO and recently appointed managing director, and others who attended the 'Women in mining symposium'. 1 ref., 6 photos.

Contract Mining versus Owner Mining

African Journals Online (AJOL)

Owner

mining companies can concentrate on their core businesses while using specialists for ... 2 Definition of Contract and Owner. Mining ... equipment maintenance, scheduling and budgeting ..... No. Region. Amount Spent on. Contract Mining. ($ billion). Percent of. Total. 1 ... cost and productivity data based on a large range.

Optimization of mining design of Hongwei uranium mine

International Nuclear Information System (INIS)

Wu Sanmao; Yuan Baixiang

2012-01-01

Combined with the mining conditions of Hongwei uranium mine, optimization schemes for hoisting cage, mine drainge,ore transport, mine wastewater treatment, power-supply system,etc are put forward in the mining design of the mine. Optimized effects are analyzed from the aspects of technique, economy, and energy saving and reducing emissions. (authors)

Fiscal 1998 engineer interexchange project (coal mine technology field). International interexchange project (Workshop in Japan); 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya). Kokusai koryu jigyo (kokunai workshop)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the workshop and technical tour held in Japan for technical interexchange of domestic and overseas engineers. From the information obtained, the higher productivity of coal mines is dependent on selective mining under blessed geological conditions, however, basically establishment of an advanced management technique for inexpensive stable operation. Both preliminary collection of geological information and introduction of advanced facilities even under unstable conditions are necessary. The balance and optimization of the whole system, and an excellent human nature for operation are also essential. Use of roof bolt supports is diffusing as improvement technology of excavation speed and roof control technology over the world. However, for introduction of new technologies, collection of test results and various kinds of training are necessary. Methane gas in coal seams as the main theme of the Hokkaido workshop is a precious unused natural resource, and important for prevention of global warming and coal mine protection measures. Its use is dependent on development of gas drainage technology. (NEDO)

Proceedings of Twenty-Seventh Annual Institute on Mining Health, Safety and Research

Energy Technology Data Exchange (ETDEWEB)

Bockosh, G.R. [ed.] [Pittsburgh Research Center, US Dept. of Energy (United States); Langton, J. [ed.] [Mine Safety and Health Administration, US Dept. of Labor (United States); Karmis, M. [ed.] [Virginia Polytechnic Institute and State University. Dept. of Mining and Minerals Engineering, Blacksburg (United States)

1996-12-31

This Proceedings contains the presentations made during the program of the Twenty-Seventh Annual Institute on Mining Health, Safety and Research held at Virginia Polytechnic Institute and State University, Blacksburg, Virginia, on August 26-28, 1996. The Twenty-Seventh Annual Institute on Mining, Health, Safety and Research was the latest in a series of conferences held at Virginia Polytechnic Institute and State University, cosponsored by the Mine Safety and Health Administration, United States Department of Labor, and the Pittsburgh Research Center, United States Department of Energy (formerly part of the Bureau of Mines, U. S. Department of Interior). The Institute provides an information forum for mine operators, managers, superintendents, safety directors, engineers, inspectors, researchers, teachers, state agency officials, and others with a responsible interest in the important field of mining health, safety and research. In particular, the Institute is designed to help mine operating personnel gain a broader knowledge and understanding of the various aspects of mining health and safety, and to present them with methods of control and solutions developed through research. Selected papers have been processed separately for inclusion in the Energy Science and Technology database.

Study on online community user motif using web usage mining

Science.gov (United States)

Alphy, Meera; Sharma, Ajay

2016-04-01

The Web usage mining is the application of data mining, which is used to extract useful information from the online community. The World Wide Web contains at least 4.73 billion pages according to Indexed Web and it contains at least 228.52 million pages according Dutch Indexed web on 6th august 2015, Thursday. It’s difficult to get needed data from these billions of web pages in World Wide Web. Here is the importance of web usage mining. Personalizing the search engine helps the web user to identify the most used data in an easy way. It reduces the time consumption; automatic site search and automatic restore the useful sites. This study represents the old techniques to latest techniques used in pattern discovery and analysis in web usage mining from 1996 to 2015. Analyzing user motif helps in the improvement of business, e-commerce, personalisation and improvement of websites.

Possible alternatives for diesel powered mobile equipment for the conditions of deep mines

Energy Technology Data Exchange (ETDEWEB)

Paraszczak, J.; Kotersi, O [Laval Univ., Quebec City, PQ (Canada). Dept. of Mining, Metallurgical and Materials Engineering

2008-07-01

The challenges associated with mining at considerable depths were discussed. Mines such as Kidd Creek, LaRonde and Creighton are deeper than 2500 m. High rock temperature is among the challenges that operators face in such conditions. Conventional diesel powered load-hauling equipment constitute an additional source of heat and noxious gases. As such, more intense ventilation is needed in order to keep ambient temperature and air quality at a level that is acceptable for human workers. This paper examined possible alternatives for diesel powered equipment, including those that are commercially available as well as those that are underdevelopment or in the prototype stage. The equipment was reviewed with reference to the required infrastructure, stage of technology development and progress. The flexibility, practicality and economic viability of the equipment was also investigated. The potential for its use in deep Canadian mines was discussed along with the most promising drive alternatives for vehicles designed for deep mine operations. Electric drives have proven to be effective in many mining applications since they have significant advantages over diesel drives. The characteristics of cable powered equipment, trolley-wire powered equipment, and battery powered equipment were described. The key advantages and disadvantages of hybrid diesel electric equipment were also reviewed along with the viability of power plants based on the use of hydrogen. The principle types of hydrogen power plants include hydrogen combustion engines; HY-Drive systems and fuel cells. It was concluded that although there is no viable alternative for diesel engines at present, Canadian mining companies operating at great depths have made significant progress in these fields and remain among the leaders in mining innovation. 17 refs.

Design of an Electronic Reminder System for Supporting the Integerity of Nursing Records.

Science.gov (United States)

Chen, Chien-Min; Hou, I-Ching; Chen, Hsiao-Ping; Weng, Yung-Ching

2016-01-01

The integrity of electronic nursing records (ENRs) stands for the quality of medical records. But patients' conditions are varied (e.g. not every patient had wound or need fall prevention), to achieve the integrity of ENRs depends much on clinical nurses' attention. Our study site, an one 2,300-bed hospital in northern Taiwan, there are a total of 20 ENRs including nursing assessments, nursing care plan, discharge planning etc. implemented in the whole hospital before 2014. It become important to help clinical nurses to decrease their human recall burden to complete these records. Thus, the purpose of this study was to design an ENRs reminder system (NRS) to facilitate nursing recording process. The research team consisted of an ENR engineer, a clinical head nurse and a nursing informatics specialist began to investigate NRS through three phases (e.g. information requirements; design and implementation). In early 2014, a qualitative research method was used to identify NRS information requirements through both groups (e.g. clinical nurses and their head nurses) focus interviews. According to the their requirements, one prototype was created by the nursing informatics specialist. Then the engineer used Microsoft Visual Studio 2012, C#, and Oracle to designed a web-based NRS (Figure 1). Then the integrity reminder system which including a total of twelve electronic nursing records was designed and the preliminary accuracy validation of the system was 100%. NRS could be used to support nursing recording process and prepared for implementing in the following phase.

Normalising corporate counterinsurgency: Engineering consent, managing resistance and greening destruction around the Hambach coal mine and beyond

NARCIS (Netherlands)

Dunlap, A.A.

2018-01-01

The German Rhineland is home to the world's largest opencast lignite coal mine and human-made hole – the Hambach mine. Over the last seven years, RWE, the mine operator, has faced an increase in militant resistance, culminating in the occupation of the Hambacher Forest and acts of civil disobedience

Assessing the blue-water footprint of an opencast platinum mine in ...

African Journals Online (AJOL)

1Industrial and Mine Water Research Unit (IMWaRU), School of Chemical and Metallurgical Engineering, University of the ... (2012) reported that increased levels of urbanisation, a lack ..... of primary copper production in northern Chile.

Geodetic monitoring (TLS of a steel transport trestle bridge located in an active mining exploitation site

Directory of Open Access Journals (Sweden)

Skoczylas Arkadiusz

2016-09-01

Full Text Available Underground mining exploitation causes, in general, irregular vertical and horizontal shifts in the superficial layer of the rock mass. In the case of construction objects seated on this layer, a deformation of the object’s foundation can be observed. This leads to additional loads and deformations. Identification of surface geometry changes in construction objects located within the premises of underground mining exploitation areas is an important task as far as safety of mining sites is concerned. Surveys targeting shifts and deformations in engineering objects preformed with the use of classic methods are of a selective nature and do not provide the full image of the phenomenon being the subject of the observation. This paper presents possibilities of terrestrial laser scanning technology application in the monitoring of engineering objects that allows for a complete spatial documentation of an object subjected to the influence of an active mining exploitation. This paper describes an observation of a 100 m section of a steel transport trestle bridge located on the premises of hard coal mine Lubelski Węgiel “Bogdanka” S.A. carried out in 2015. Measurements were carried out using a Z+F Imager 5010C scanner at an interval of 3.5 months. Changes in the structure’s geometry were determined by comparing the point clouds recorded during the two measurement periods. The results of the analyses showed shifts in the trestle bridge towards the exploited coal wall accompanied by object deformation. The obtained results indicate the possibility of of terrestrial laser scanning application in studying the aftereffects of underground mining exploitation on surface engineering objects.

Data Mining Foundations and Intelligent Paradigms Volume 2 Statistical, Bayesian, Time Series and other Theoretical Aspects

CERN Document Server

Jain, Lakhmi

2012-01-01

Data mining is one of the most rapidly growing research areas in computer science and statistics. In Volume 2 of this three volume series, we have brought together contributions from some of the most prestigious researchers in theoretical data mining. Each of the chapters is self contained. Statisticians and applied scientists/ engineers will find this volume valuable. Additionally, it provides a sourcebook for graduate students interested in the current direction of research in data mining.

Effects of organizational safety practices and perceived safety climate on PPE usage, engineering controls, and adverse events involving liquid antineoplastic drugs among nurses.

Science.gov (United States)

DeJoy, David M; Smith, Todd D; Woldu, Henok; Dyal, Mari-Amanda; Steege, Andrea L; Boiano, James M

2017-07-01

Antineoplastic drugs pose risks to the healthcare workers who handle them. This fact notwithstanding, adherence to safe handling guidelines remains inconsistent and often poor. This study examined the effects of pertinent organizational safety practices and perceived safety climate on the use of personal protective equipment, engineering controls, and adverse events (spill/leak or skin contact) involving liquid antineoplastic drugs. Data for this study came from the 2011 National Institute for Occupational Safety and Health (NIOSH) Health and Safety Practices Survey of Healthcare Workers which included a sample of approximately 1,800 nurses who had administered liquid antineoplastic drugs during the past seven days. Regression modeling was used to examine predictors of personal protective equipment use, engineering controls, and adverse events involving antineoplastic drugs. Approximately 14% of nurses reported experiencing an adverse event while administering antineoplastic drugs during the previous week. Usage of recommended engineering controls and personal protective equipment was quite variable. Usage of both was better in non-profit and government settings, when workers were more familiar with safe handling guidelines, and when perceived management commitment to safety was higher. Usage was poorer in the absence of specific safety handling procedures. The odds of adverse events increased with number of antineoplastic drugs treatments and when antineoplastic drugs were administered more days of the week. The odds of such events were significantly lower when the use of engineering controls and personal protective equipment was greater and when more precautionary measures were in place. Greater levels of management commitment to safety and perceived risk were also related to lower odds of adverse events. These results point to the value of implementing a comprehensive health and safety program that utilizes available hazard controls and effectively communicates

Surface Mines, Other - Longwall Mining Panels

Data.gov (United States)

NSGIC Education | GIS Inventory — Coal mining has occurred in Pennsylvania for over a century. A method of coal mining known as Longwall Mining has become more prevalent in recent decades. Longwall...

Origins of inhabitants from the 16th century Sala (Sweden) silver mine cemetery – a lead isotope perspective

DEFF Research Database (Denmark)

Price, T. Douglas; Frei, Robert; Bäckström, Ylva

2017-01-01

Historical documents record the operation of a silver mine from the 16th century AD located near the former village of Salberget in central Sweden. The historical record describes several categories of inhabitants, including local families, workers and miners, foreign engineers and mining...

Application for trackless mining technique in Benxi uranium mine

International Nuclear Information System (INIS)

Chen Bingguo

1998-01-01

The author narrates the circumstances achieving constructional target in Benxi Uranium Mine under relying on advance of science and technology and adopting small trackless mining equipment, presents the application of trackless mining equipment at mining small mine and complex mineral deposit and discusses the unique superiority of trackless mining technique in development work, mining preparation work and backstoping

An evaluation of fuels and retrofit diesel particulate filters to reduce diesel particulate matter emissions in an underground mine

CSIR Research Space (South Africa)

Wattrus, MC

2016-09-01

Full Text Available Through an industry wide collaborative project, this paper explores what potential exists for South African underground mines to reduce diesel particulate emissions, where the starting point is a mine using older engine technology (Tier 1 emission...

Influence of ergonomic design on trackless mining machines on the health and safety of the operators, drivers and workers.

CSIR Research Space (South Africa)

Mason, S

1998-07-01

Full Text Available The project has produced information and methodologies for use by designers, mine managers and engineers to improve the health and safety associated with the use of trackless vehicles in mines. The project deliverables focus on assisting; designers...

Addressing Practical Issues Related Tto Nursing Care For International Visitors To Hiroshima

Directory of Open Access Journals (Sweden)

Mariko Nishikawa

2014-04-01

Full Text Available When nine million foreigners visited Japan in 2013, the federal government set a goal to attract an additional two and a half million visitors including medical tourists by 2020. This research investigates the attitudes and concerns of Japanese nurses when they are in a situation dealing with foreign patients. The data were collected from March through September 2010, from 114 nurses at three hospitals, in close proximity to popular tourist destinations in Hiroshima. A questionnaire was developed for this research, named Mari Meter, which included a section to write answers to an open question for the nurses to express their opinions. These responses were examined statistically and by word analysis using Text Mining Studio. Japanese nurses expressed greatest concern about payment options, foreign language skills, and issues of informed consent, when dealing with foreigners. The results confirm that, in order to provide a high quality of patient care, extra preparation and a greater knowledge of international workers and visitors are required by nursing professionals in Japan.

The use of constructed wetlands in the treatment of acid mine drainage

International Nuclear Information System (INIS)

Perry, A.; Kleinmann, R.L.P.

1991-01-01

US government regulations require that all effluents from industrial operations, including mining, meet certain water quality standards. Constructed wetlands have proven to be useful in helping to attain those standards. Application of this biotechnology to mine water drainage can reduce water treatment costs and improve water quality in streams and rivers adversely affected by acidic mine water drainage from abandoned mines. Over 400 constructed wetland water treatment systems have been built on mined lands largely as a result of research by the US Bureau of Mines. Wetlands are passive biological treatment systems that are relatively inexpensive to construct and require minimal maintenance. Chemical treatment costs are reduced sufficiently to repay the cost of construction in less than a year. The mine waste water is typically treated in a series of excavated ponds that resemble small marsh areas. The ponds are engineered to facilitate bacterial oxidation of iron. Ideally, the water then flows through a composted organic substrate supporting a population of sulphate-reducing bacteria which raises the pH. Constructed wetlands in the USA are described - their history, functions, construction methodologies, applicabilities, limitations and costs. (author). 26 refs, 2 figs

The use of constructed wetlands in the treatment of acid mine drainage

Energy Technology Data Exchange (ETDEWEB)

Perry, A [Department of the Interior, Washington, DC (United States). Bureau of Mines; Kleinmann, R L.P. [Department of the Interior, Pittsburgh, PA (United States). Bureau of Mines

1991-08-01

US government regulations require that all effluents from industrial operations, including mining, meet certain water quality standards. Constructed wetlands have proven to be useful in helping to attain those standards. Application of this biotechnology to mine water drainage can reduce water treatment costs and improve water quality in streams and rivers adversely affected by acidic mine water drainage from abandoned mines. Over 400 constructed wetland water treatment systems have been built on mined lands largely as a result of research by the US Bureau of Mines. Wetlands are passive biological treatment systems that are relatively inexpensive to construct and require minimal maintenance. Chemical treatment costs are reduced sufficiently to repay the cost of construction in less than a year. The mine waste water is typically treated in a series of excavated ponds that resemble small marsh areas. The ponds are engineered to facilitate bacterial oxidation of iron. Ideally, the water then flows through a composted organic substrate supporting a population of sulphate-reducing bacteria which raises the pH. Constructed wetlands in the USA are described - their history, functions, construction methodologies, applicabilities, limitations and costs. (author). 26 refs, 2 figs.

Mining Together : Large-Scale Mining Meets Artisanal Mining, A Guide for Action

OpenAIRE

World Bank

2009-01-01

The present guide mining together-when large-scale mining meets artisanal mining is an important step to better understanding the conflict dynamics and underlying issues between large-scale and small-scale mining. This guide for action not only points to some of the challenges that both parties need to deal with in order to build a more constructive relationship, but most importantly it sh...

Strata control in mineral engineering

International Nuclear Information System (INIS)

Bieniawski, Z.T.

1986-01-01

This book covers the state-of-the-art of strata control practice both in the United States and abroad with respect to strata reinforcement by rock bolting, long wall mining technology and innovations in energy development, such as mining for oil and tunneling for storage of high-level nuclear waste in deep underground repositories. It features coverage of design concepts in rock engineering and rockbolt systems, stability of rock pillars, rockbursts, shaft design and construction and a detailed consideration of mineral and energy needs in the United States

From chemical risk assessment to environmental resources management: the challenge for mining.

Science.gov (United States)

Voulvoulis, Nikolaos; Skolout, John W F; Oates, Christopher J; Plant, Jane A

2013-11-01

On top of significant improvements and progress made through science and engineering in the last century to increase efficiency and reduce impacts of mining to the environment, risk assessment has an important role to play in further reducing such impacts and preventing and mitigating risks. This paper reflects on how risk assessment can improve planning, monitoring and management in mining and mineral processing operations focusing on the importance of better understanding source-pathway-receptor linkages for all stages of mining. However, in light of the ever-growing consumption and demand for raw materials from mining, the need to manage environmental resources more sustainably is becoming increasingly important. The paper therefore assesses how mining can form an integral part of wider sustainable resources management, with the need for re-assessing the potential of mining in the context of sustainable management of natural capital, and with a renewed focus on its the role from a systems perspective. The need for understanding demand and pressure on resources, followed by appropriate pricing that is inclusive of all environmental costs, with new opportunities for mining in the wastes we generate, is also discussed. Findings demonstrate the need for a life cycle perspective in closing the loop between mining, production, consumption and waste generation as the way forward.

Proceedings of the 18. international symposium on mine planning and equipment selection (MPES 2009) and the 11. international symposium on environmental issues and waste management in energy and mineral production (SWEMP 2009) : mine planning and equipment selection and environmental issues and waste management in energy and mineral production

International Nuclear Information System (INIS)

Singhal, R.K.; Mehrotra, A.; Fytas, K.; Ge, H.

2009-01-01

This conference focused on the application of innovative technologies to the mineral industries and the development of productive methods for the mining and processing industries. It was attended by participants from North and South America, Europe, Australia, Africa and Asia with backgrounds in computer sciences, mining engineering and research in mineral production. The major topics addressed regarding mine planning and equipment selection included economic and technical feasibility studies; reserve estimation; mine development; design and planning of surface and underground mines; drilling, blasting, tunneling and excavation engineering; mining equipment selection; automation and information technology; maintenance and production management for mines and mining systems; mining in terms of health, safety and the environment; and rock mechanics and geotechnical applications. The topics addressed regarding waste management in energy and mineral production included the environmental impacts of coal-fired power projects; mining and reclamation; water management; social aspects of rehabilitation; sustainable development for mineral and energy industries; remediation of contaminated soil and groundwater; health hazard and safety issues in small-scale mining; environmental issues in surface and underground mining of metalliferous, coal, uranium and industrial minerals; occupational health and safety; control of effluents from mineral processing, metallurgy and chemical plants; emerging technologies for environmental protection; reliability of waste containment structures; and tailings treatment, recycling and disposal. The conference featured 162 presentations, of which 30 have been catalogued separately for inclusion in this database. refs., tabs., figs.

Competitive platinum-group-metal (PGM) supply from the Eastern Limb, Bushveld Complex: Geological, mining and mineral economic aspects

CSIR Research Space (South Africa)

McGill, JE

2011-08-01

Full Text Available -GROUP-METAL (PGM) SUPPLY FROM THE EASTERN LIMB, BUSHVELD COMPLEX: GEOLOGICAL, MINING, AND MINERAL ECONOMIC ASPECTS Dr. Jeannette E. McGill & Prof. Murray W. Hitzman ACKNOWLEDGEMENTS ? COUNCIL FOR SCIENTIFIC AND INDUSTRIAL RESEARCH (CSIR) ? Centre for Mining... Innovation ? Office of Graduate Studies, Fogarty Endowment ? Mr. VISHNU PILLAY (EXECUTIVE HEAD: JV?S ? Anglo Platinum) ? ACADEMIC ADVISORS Prof. Murray Hitzman (Economic Geology); Dr. Hugh Miller (Mining Engineering); Prof. Rodderick Eggert (Mineral...

Electrical resistivity imaging survey to detect uncharted mine galleries in the mining district of Linares, Jaén, Spain

Science.gov (United States)

Martínez-López, J.; Rey, J.; Dueñas, J.; Hidalgo, C.; Benavente, J.

2012-02-01

The scarcity of information about the existence of old mining shafts and galleries in urban areas is an important issue for future urban development. Electrical resistivity tomography is a non-destructive geophysical technique that can detect and characterize such subsurface cavities based on differences in the behaviour of electrical current in the void and in the embedding rock. Here we present a study in which this technique was used to determine the location of old engineered structures around the city of Linares, southern Spain, and to relate these structures to the abandoned deep mines present in the area. Eight electrical resistivity imaging profiles were performed, with a total of 22 808 measurements. Correlations between geoelectrical anomalies allow detection of the depth and the direction of several galleries, as well as the voids that result from mining extraction. Given the depth at which these structures are located (in some cases less than 5 m), they pose an important risk for future construction projects in areas of urban expansion. This technique is shown to be a useful tool for locating areas that pose important urban risks and, by extension, for the decision-making process in territorial planning, especially in areas with a history of deep mining.

Electrical resistivity imaging survey to detect uncharted mine galleries in the mining district of Linares, Jaén, Spain

International Nuclear Information System (INIS)

Martínez-López, J; Rey, J; Hidalgo, C; Dueñas, J; Benavente, J

2012-01-01

The scarcity of information about the existence of old mining shafts and galleries in urban areas is an important issue for future urban development. Electrical resistivity tomography is a non-destructive geophysical technique that can detect and characterize such subsurface cavities based on differences in the behaviour of electrical current in the void and in the embedding rock. Here we present a study in which this technique was used to determine the location of old engineered structures around the city of Linares, southern Spain, and to relate these structures to the abandoned deep mines present in the area. Eight electrical resistivity imaging profiles were performed, with a total of 22 808 measurements. Correlations between geoelectrical anomalies allow detection of the depth and the direction of several galleries, as well as the voids that result from mining extraction. Given the depth at which these structures are located (in some cases less than 5 m), they pose an important risk for future construction projects in areas of urban expansion. This technique is shown to be a useful tool for locating areas that pose important urban risks and, by extension, for the decision-making process in territorial planning, especially in areas with a history of deep mining

[Application of an improved model of a job-matching platform for nurses].

Science.gov (United States)

Huang, Way-Ren; Lin, Chiou-Fen

2015-04-01

The three-month attrition rate for new nurses in Taiwan remains high. Many hospitals rely on traditional recruitment methods to find new nurses, yet it appears that their efficacy is less than ideal. To effectively solve this manpower shortage, a nursing resource platform is a project worth developing in the future. This study aimed to utilize a quality-improvement model to establish communication between hospitals and nursing students and create a customized employee-employer information-matching platform to help nursing students enter the workforce. This study was structured around a quality-improvement model and used current situation analysis, literature review, focus-group discussions, and process re-engineering to formulate necessary content for a job-matching platform for nursing. The concept of an academia-industry strategic alliance helped connect supply and demand within the same supply chain. The nurse job-matching platform created in this study provided job flexibility as well as job suitability assessments and continued follow-up and services for nurses after entering the workforce to provide more accurate matching of employers and employees. The academia-industry strategic alliance, job suitability, and long-term follow-up designed in this study are all new features in Taiwan's human resource service systems. The proposed human resource process re-engineering provides nursing students facing graduation with a professionally managed human resources platform. Allowing students to find an appropriate job prior to graduation will improve willingness to work and employee retention.

Recovery of uranium in mine waters; Recuperation de l'uranium dans les eaux des mines

Energy Technology Data Exchange (ETDEWEB)

Sugier, P [Direction des Productions, CEA, Chatillon-Sur-Bagneux (France)

1967-06-15

In a brief introductory survey the author indicates the date on which leaching was first observed in the CEA mines and lists the main factors necessary for, or favourable to, the solubilization of uranium in mines. Information is given on the various sources of this type at present identified in France and the methods used to recover uranium in mines situated near ore-concentration plants. An explanation is given for the use of the calcium precipitation technique in connection with waters produced in mines not situated near ore-concentration plants. Data are given on the results of laboratory tests carried out on waters containing uranium, together with a description of an industrial-scale facility built in consequence of these tests. Details are given of the statistical results obtained. The author concludes by outlining the programme which will be implemented in the near future with a view to increasing the tonnage of uranium produced by in situ leaching and indicates that the CEA engineers are very optimistic about the prospects of this new low-cost method of producing uranium. (author) [French] Apres un bref rappel historique precisant la date de constatation du phenomene de lixiviation dans les mines d'uranium du Commissariat et un rapide inventaire des principales conditions necessaires ou favorisant la solubilisation de l'uranium dans les mines, auteur indique les differentes sources actuellement reconnues en France et les methodes utilisees pour recuperer l'uranium dans les mines situees pres d'une usine de concentration des minerais. Il donne ensuite les raisons motivant le choix du procede de precipitation calcique pour les eaux produites dans des mines eloignees des usines de concentration des minerais. Les resultats d'essais de laboratoire effectues sur des eaux chargees en uranium sont donnes et l'installation industrielle realisee a la suite de ces essais est decrite; les resultats statistiques obtenus sont detailles. En conclusion de son expose, l

Participation of Ostrava Mining College in training of personnel for nuclear technology

International Nuclear Information System (INIS)

Kuchar, L.

1983-01-01

The mining and geology faculty of the Mining College educates specialists for surveying, extraction and treatment of uranium raw materials. In 1980 the faculty introduced an interdisciplinary study course for the technology of drilling, geological surveying and mine surveying. A contract has been signed between the College and the Czechoslovak Uranium Industry on specialized and scientific cooperation, expertise, postgraduate courses, etc. The metallurgy faculty of the College introduced the nuclear metallurgy specialization in 1964. Students attending the course will acquire knowledge not only on the metallurgy of nuclear fuels, cladding, shielding and structural materials, their production and processing but also on the science of metals, heat treatment, metal testing, etc. A study course is now being prepared relating to materials problems of nuclear power which is oriented to modern methods of material assessment for nuclear power facilities, light water reactors and their components. In 1976 the Mining College also introduced the nuclear power specialization at its mechanical engineering and electrical engineering faculties. In the years 1976-1982 more than fifty students graduated from the faculty whose theses were oriented to the problems of welding, surfacing, machining and upgrading of WWER-440 and WWER-1000 components. In the years 1979-82 the College ran a postgraduate study course on ''Machines and equipment of nuclear power plants''. (E.S.)

Exploring the Synergic Effects of Nursing Home Work on Work-Related Musculoskeletal Disorders Among Nursing Assistants.

Science.gov (United States)

Ching, Shirley S Y; Szeto, Grace; Lai, Godfrey Kin Bun; Lai, Xiao Bin; Chan, Ying Tung; Cheung, Kin

2018-03-01

Little is known about how nursing assistants (NAs) perceive the nature of their work and how their work contributes to work-related musculoskeletal disorders (WMSDs). This qualitative study addressed these gaps. Twenty-four NAs with WMSDs working in four nursing homes participated in semistructured focus group interviews. Their WMSDs were not limited to the lower back but involved several body parts. The risk factors for WMSDs included physical, psychosocial, organizational, and personal factors as well as coworkers and clients. However, it is the synergistic effects of long work hours without sufficient rest, work even with musculoskeletal pain because of staff shortages, ineffective management with insufficient prework training and inadequate equipment maintenance, and an aging workforce with strong commitment to resident care that play a crucial role in WMSDs among NAs working in nursing homes. The study found that multidimensional intervention strategies using engineering, administrative, and personal controls should be developed to reduce WMSDs among NAs working in nursing homes.

Systems Engineering as a tool; Verktoeyet Systems Engineering : struktur fra start til maal

Energy Technology Data Exchange (ETDEWEB)

Carlsen, Randi

2002-07-01

Systems engineering integrates all types of specialists and disciplines into teams that try to create a structured development process from concept via production to operation. The idea is that by using systems engineering, projects can be completed efficiently and successfully. It is important that the individual participant in a project understands that he or she works within a system and that there is a need for skill, comprehensiveness and communication. Systems engineering comprises system design, computer aided design, cybernetics and mecatronics. The article describes the use of systems engineering in a student project in which a heat pump will be used to utilize the energy potential of ground water primarily to heat the visitors' area in a mine museum in Kongsberg, Norway.

Implementation of Paste Backfill Mining Technology in Chinese Coal Mines

Science.gov (United States)

Chang, Qingliang; Zhou, Huaqiang; Bai, Jianbiao

2014-01-01

Implementation of clean mining technology at coal mines is crucial to protect the environment and maintain balance among energy resources, consumption, and ecology. After reviewing present coal clean mining technology, we introduce the technology principles and technological process of paste backfill mining in coal mines and discuss the components and features of backfill materials, the constitution of the backfill system, and the backfill process. Specific implementation of this technology and its application are analyzed for paste backfill mining in Daizhuang Coal Mine; a practical implementation shows that paste backfill mining can improve the safety and excavation rate of coal mining, which can effectively resolve surface subsidence problems caused by underground mining activities, by utilizing solid waste such as coal gangues as a resource. Therefore, paste backfill mining is an effective clean coal mining technology, which has widespread application. PMID:25258737

Decommissioning of uranium mines and mills - Canadian regulatory approach and experience

International Nuclear Information System (INIS)

Whitehead, W.

1986-09-01

At the time of the recent closures of the Agnew Lake, Beaverlodge and Madawaska Mines Limited uranium mining and milling facilities, several relevant regulatory initiatives, including the development of decommissioning criteria, were underway, or contemplated. In the absence of precedents, the regulatory agencies and companies involved adopted approaches to the decommissioning of these facilities that reflected site specific circumstances, federal and provincial regulatory requirements, and generally accepted principles of good engineering practice and environmental protection. This paper summarizes related historical and current regulatory policies, requirements and guidelines; including those implemented at the three decommissioned sites

Mining-metallurgical projects for the production of uranium concentrates

International Nuclear Information System (INIS)

Ajuria-Garza, S.

1983-01-01

This report presents an overall view of a complete project for a mining-metallurgical complex for the production of uranium concentrates. Relevant aspects of each important topic are discussed as parts of an integrated methodology. The principal project activities are analyzed and the relationships among the various factors affecting the design are indicated. A list of 96 principal activities is proposed as an example. These activities are distributed in eight groups: initial evaluations preliminary feasibility studies, project engineering, construction, industrial operation, decommissioning and post-decommissioning activities. The environmental impact and the radiological risks due to the construction and operation of the mining metallurgical complex are analyzed. The principles of radiological protection and the regulations, standards and recommendations for radiological protection in uranium mines and mills are discussed. This report is also a guide to the specialized literature: a bibliography with 765 references is included. (author)

Geomorphic factors in the rehabilitation of earthen mine structures (with reference to uranium mining in the Northern Territory)

International Nuclear Information System (INIS)

Cull, R.F.; East, T.J.

1987-01-01

Geomorphic research forms part of the Institute's brief of researching the effects of uranium mining on the environment of the Alligator Rivers Region of which Kakadu National Park is a part. A major research focus is the containment of uranium mill tailings and non uraniferous solid wastes within the confines of mine areas. Government guidelines specify that the objective in the engineering of a tailings management structure should be to attain a design life of at least 200 years and a structural life of a substantially longer period - perhaps a 1000 years. It is this need to incorporate a 1000-year time frame which necessitates the inclusion of geomorphic factors into the design of rehabilitated structures. The study being undertaken treats steep natural hillslopes in the region as analogues of rehabilitated slopes. The aim of the study is to investigate the properties of steep (stable) natural hillslopes in order to determine what characteristics impart their inherent stability against both mass movement and erosion. It is proposed then to incorporate these characteristics in the design of rehabilitated structures. Whilst this research is directed primarily at the rehabilitation of earthen structures at mines in the Alligator Rivers Region, geomorphic principles should also be applicable in rehabilitation of waste rock and overburden stockpiles, tailings dams and other earthen mine structures in a variety of environments

A Visualization Tool for Integrating Research Results at an Underground Mine

Science.gov (United States)

Boltz, S.; Macdonald, B. D.; Orr, T.; Johnson, W.; Benton, D. J.

2016-12-01

Researchers with the National Institute for Occupational Safety and Health are conducting research at a deep, underground metal mine in Idaho to develop improvements in ground control technologies that reduce the effects of dynamic loading on mine workings, thereby decreasing the risk to miners. This research is multifaceted and includes: photogrammetry, microseismic monitoring, geotechnical instrumentation, and numerical modeling. When managing research involving such a wide range of data, understanding how the data relate to each other and to the mining activity quickly becomes a daunting task. In an effort to combine this diverse research data into a single, easy-to-use system, a three-dimensional visualization tool was developed. The tool was created using the Unity3d video gaming engine and includes the mine development entries, production stopes, important geologic structures, and user-input research data. The tool provides the user with a first-person, interactive experience where they are able to walk through the mine as well as navigate the rock mass surrounding the mine to view and interpret the imported data in the context of the mine and as a function of time. The tool was developed using data from a single mine; however, it is intended to be a generic tool that can be easily extended to other mines. For example, a similar visualization tool is being developed for an underground coal mine in Colorado. The ultimate goal is for NIOSH researchers and mine personnel to be able to use the visualization tool to identify trends that may not otherwise be apparent when viewing the data separately. This presentation highlights the features and capabilities of the mine visualization tool and explains how it may be used to more effectively interpret data and reduce the risk of ground fall hazards to underground miners.

The psychosocial impacts of fly-in fly-out and drive-in drive-out mining on mining employees: a qualitative study.

Science.gov (United States)

Torkington, Amanda May; Larkins, Sarah; Gupta, Tarun Sen

2011-06-01

To explore how fly-in fly-out (FIFO) and drive-in drive-out (DIDO) mining affects the psychosocial well-being of miners resident in a rural north Queensland town as well as the sources of support miners identify and use in managing these effects. A descriptive qualitative study, using semistructured interviews. Charters Towers, a rural town in north Queensland, and a remote north-western Queensland mine. Eleven people, resident in or near Charters Towers, currently or formerly employed in FIFO or DIDO mining. Self-reported effects on psychosocial well-being and sources of support. Participants reported positive and negative psychosocial impacts across domains including family life, relationships, social life, work satisfaction, mood, sleep and financial situation. Concerns about the impact on participants' partners were described. Awareness of onsite support, such as Employee Assistance Programs, varied. Other supports included administration staff and nurses or medics. Trusted friends or colleagues at the mine site were considered a preferred means of support. Some, but not most, had experienced coworkers discussing problems with them. A reluctance to seek support was described, with a number of barriers identified. Those having problems might not recognise their own stress and thus not seek support. This study identifies numerous psychosocial impacts on FIFO/DIDO miners and their partners, and provides insights into preferences regarding support. Employee Assistance Programs cannot be relied upon as the sole means of support. Further studies exploring the impact upon and supports for FIFO/DIDO workers and their partners will assist in better understanding these issues. © 2011 The Authors. Australian Journal of Rural Health © National Rural Health Alliance Inc.

A field trail for sealing abandoned mine shafts and adits with lightweight concrete

International Nuclear Information System (INIS)

Skinner, E.H.; Beckett, L.A.

1994-01-01

An abandoned mine shaft near Omar, in Logan County, WV, was permanently sealed through a cooperative agreement between the West Virginia Department of Commerce, Labor, and Environmental Resources, Division of Environmental Protection, and the US Bureau of Mines (USBM), Abandoned Mine Lands (AML) Program. An engineered shaft seal design was developed and demonstrated that featured lightweight concrete as a key material component at a wet density of about 45 lb/ft 3 . A reinforced concrete cap designed for 5 psi live load was placed over the shaft seal. Applicable new concrete technologies relating to a 100-yr design life were utilized to assure future integrity of the shaft seal. Waterproofing methods were included in the shaft seal design to provide protection from ambient moisture and corrosive mine waters and to increase the long-term durability of the shaft seal. All construction methods used in the field trial are fully adaptable for the mine-reclamation contractor. The USBM research objectives were to develop a broad generic design that will be widely applicable to other adit-sealing and shaft-sealing problems throughout the mining industry

Uranium in situ leach mining in the United States. Information circular

International Nuclear Information System (INIS)

Larson, W.C.

1978-01-01

This report discusses uranium in situ leach mining in the United States; the purpose of which is to acquaint the reader with an overview of this emerging mining technology. This report is not a technical discussion of the subject matter, but rather should be used as a reference source for information on in situ leaching. An in situ leaching bibliography is included as well as engineering data tables for almost all of the active pilot-scale and commercial uranium in situ leaching operators. These tables represent a first attempt at consolidating operational data in one source, on a regional scale. Additional information is given which discusses the current Bureau of Mines uranium in situ leaching research program. Also included is a listing of various State and Federal permitting agencies, and a summary of the current uranium in situ leaching operators. Finally, a glossary of terms has been added, listing some of the more common terms used in uranium in situ leach mining

Retrofit SCR system for NOx control from heavy-duty mining equipment

International Nuclear Information System (INIS)

Mannan, M.A.

2009-01-01

Diesel engines are used extensively in the mining industry and offer many advantages. However, particulate matter (PM) emissions and nitrogen oxide emissions (NOx) are among its disadvantages. A significant concern related to PM and NOx in an underground mine involves the use of diesel exhaust after treatment systems such as diesel particulate filters and selective catalytic reduction (SCR). This presentation discussed NOx and PM control and provided a description of an SCR system and examples of SCR retrofits. Options for NOx control were discussed and a case study involving the installation of an SCR retrofit system in an underground mine operated by Sifto Salt was also presented. The purpose of the case study was to identify cost effective retrofit solutions to lower nitrogen dioxide emissions from heavy-duty trucks operating in underground mines. The case study illustrated and presented the candidate vehicle, baseline emissions, a BlueMax SCR retrofit solution, and BlueMax installation. 1 tab., 6 figs.

30 CFR 819.21 - Auger mining: Protection of underground mining.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Auger mining: Protection of underground mining. 819.21 Section 819.21 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT... STANDARDS-AUGER MINING § 819.21 Auger mining: Protection of underground mining. Auger holes shall not extend...

Research on application of mobile diesel equipment in underground mines 2

Energy Technology Data Exchange (ETDEWEB)

Kim, Bok Youn; Kang, Chang Hee; Jo, Young Do; Lim, Sang Taek [Korea Inst. of Geology Mining and Materials, Taejon (Korea, Republic of)

1995-12-01

It is 2 nd year of the research project on application of mobile diesel equipment in underground mines for providing appropriate measures to improve underground working environment contaminated by the diesel exhaust pollutants. Studies on Diesel Particulate Matter(DPM), which is regarded as a carcinogenic substances, was carried out intensively to figure out which substance is the most critical one among the diesel exhaust pollutants. The production mechanism and health effects of DPM, and evaluation of hazard level of underground workings was conducted. For development of exhaust treatment devices and recommendation of the best concept suitable for local conditions has been done. And the basic guidelines for good engine maintenance to provide the safe and healthful use of diesel-powered mine equipment were suggested so that field engineers can use it as a reference in daily operations. (author). 19 refs., 31 figs., 41 tabs.

Sustainable lignite mining and utilization. Developments in the Rhenish lignite-mining area; Nachhaltige Braunkohlegewinnung und -nutzung. Entwicklung im Rheinischen Revier

Energy Technology Data Exchange (ETDEWEB)

Gaertner, Dieter [RWE Power AG, Bergheim (Germany). Opencast Mines Div.

2012-03-15

Lignite is an essential module in the Rhenish mining area's economic power. Mining in a densely populated region like the Rhineland calls for keeping an eye equally on people, the environment and industry now and in the future. By considering all concerns and ensuring transparency in our approach to people, we have succeeded in obtaining public acceptance also for large-scale projects in an environment that is not always easy in Germany. RWE Power plans to use lignite in power generation and in upgrading operations for many decades to come, so that the company is systematically implementing the power-plant renewal programme with is planning for BoAplus as highly efficient next-generation lignite-based power plants. Research on CO{sub 2} utilization, flexibilization, energy storage and alternative uses of lignite are as much features of RWE Power's future-proof alignment in the Rhenish mining area as are further innovations in the opencast mines. Core aspects here include further automation in the deployment of main mine equipment, closely dovetailed with innovations in other operating units. Parallel restructuring of the operating units and the Lignite Approvals area are underpinning these measures. Innovations and their translation into technical progress will ensure the success of a measured energy turnaround both in Germany and throughout Europe. However, this requires dependable political conditions, so that an engineering spirit can go on being transformed into entrepreneurial action. (orig.)

Job Prospects for Metallurgical Engineering.

Science.gov (United States)

Basta, Nicholas

1985-01-01

Job prospects in mining, metal-extraction, steel, and refining industries are depressed, but technological discoveries are opening up new fields for metallurgical engineers. Enrollment/employment opportunities and salaries in these areas are discussed a well as the roles of foreign competition, plastics applications, and ceramics research and…

Contract Mining versus Owner Mining – The Way Forward | Suglo ...

African Journals Online (AJOL)

Ghana Mining Journal ... By contracting out one or more of their mining operations, the mining companies can concentrate on their core businesses. This paper reviews ... The general trends in the mining industry show that contract mining will be the way forward for most mines under various circumstances in the future.

Engineering sustainable ecosystems: using GIS-based habitat modeling for oil sands mine reclamation and closure planning

International Nuclear Information System (INIS)

Seel, K.

1997-01-01

A GIS model was built to predict the climax vegetation habitat types on reclaimed mine surfaces in the Fort McMurray region of the Mid-Boreal Mixedwood Ecoregion of northwestern Alberta. Regional vegetation habitat types were classified by digital remote sensing using Landsat Thematic Mapper satellite data. Terrain data was derived from a high-resolution digital elevation model. The validated model was applied to the GIS database of Syncrude Canada's Mildred Lake Mine to predict future vegetation patterns based on the final closure mine surface. The results were compared to revegetation and closure plans created by experts to analyze performance and sustainability of reclamation efforts

Recommendation systems in software engineering

CERN Document Server

Robillard, Martin P; Walker, Robert J; Zimmermann, Thomas

2014-01-01

With the growth of public and private data stores and the emergence of off-the-shelf data-mining technology, recommendation systems have emerged that specifically address the unique challenges of navigating and interpreting software engineering data.This book collects, structures and formalizes knowledge on recommendation systems in software engineering. It adopts a pragmatic approach with an explicit focus on system design, implementation, and evaluation. The book is divided into three parts: "Part I - Techniques" introduces basics for building recommenders in software engineering, including techniques for collecting and processing software engineering data, but also for presenting recommendations to users as part of their workflow.?"Part II - Evaluation" summarizes methods and experimental designs for evaluating recommendations in software engineering.?"Part III - Applications" describes needs, issues and solution concepts involved in entire recommendation systems for specific software engineering tasks, fo...

Practical mine ventilation optimization based on genetic algorithms for free splitting networks

Energy Technology Data Exchange (ETDEWEB)

Acuna, E.; Maynard, R.; Hall, S. [Laurentian Univ., Sudbury, ON (Canada). Mirarco Mining Innovation; Hardcastle, S.G.; Li, G. [Natural Resources Canada, Sudbury, ON (Canada). CANMET Mining and Mineral Sciences Laboratories; Lowndes, I.S. [Nottingham Univ., Nottingham (United Kingdom). Process and Environmental Research Division; Tonnos, A. [Bestech, Sudbury, ON (Canada)

2010-07-01

The method used to optimize the design and operation of mine ventilation has generally been based on case studies and expert knowledge. It has yet to benefit from optimization techniques used and proven in other fields of engineering. Currently, optimization of mine ventilation systems is a manual based decision process performed by an experienced mine ventilation specialist assisted by commercial ventilation distribution solvers. These analysis tools are widely used in the mining industry to evaluate the practical and economic viability of alternative ventilation system configurations. The scenario which is usually selected is the one that reports the lowest energy consumption while delivering the required airflow distribution. Since most commercial solvers do not have an integrated optimization algorithm network, the process of generating a series of potential ventilation solutions using the conventional iterative design strategy can be time consuming. For that reason, a genetic algorithm (GA) optimization routine was developed in combination with a ventilation solver to determine the potential optimal solutions of a primary mine ventilation system based on a free splitting network. The optimization method was used in a small size mine ventilation network. The technique was shown to have the capacity to generate good feasible solutions and improve upon the manual results obtained by mine ventilation specialists. 9 refs., 7 tabs., 3 figs.

Application of a Novel Liquid Nitrogen Control Technique for Heat Stress and Fire Prevention in Underground Mines.

Science.gov (United States)

Shi, Bobo; Ma, Lingjun; Dong, Wei; Zhou, Fubao

2015-01-01

With the continually increasing mining depths, heat stress and spontaneous combustion hazards in high-temperature mines are becoming increasingly severe. Mining production risks from natural hazards and exposures to hot and humid environments can cause occupational diseases and other work-related injuries. Liquid nitrogen injection, an engineering control developed to reduce heat stress and spontaneous combustion hazards in mines, was successfully utilized for environmental cooling and combustion prevention in an underground mining site named "Y120205 Working Face" (Y120205 mine) of Yangchangwan colliery. Both localized humidities and temperatures within the Y120205 mine decreased significantly with liquid nitrogen injection. The maximum percentage drop in temperature and humidity of the Y120205 mine were 21.9% and 10.8%, respectively. The liquid nitrogen injection system has the advantages of economical price, process simplicity, energy savings and emission reduction. The optimized heat exchanger used in the liquid nitrogen injection process achieved superior air-cooling results, resulting in considerable economic benefits.

Selection of mining method for No.3 uranium ore body in the independent mining area at a uranium mine

International Nuclear Information System (INIS)

Ding Fulong; Ding Dexin; Ye Yongjun

2010-01-01

Mining operation in the existed mining area at a uranium mine is near completion and it is necessary to mine the No.3 uranium ore body in another mining area at the mine. This paper, based on the geological conditions, used analogical method for analyzing the feasible methods and the low cost and high efficiency mining method was suggested for the No.3 ore body in the independent mining area at the uranium mine. (authors)

Automation of mining machinery at RAG; Automation von Bergbaumaschinen bei der RAG Deutsche Steinkohle

Energy Technology Data Exchange (ETDEWEB)

Barabasch, Uwe [Zentralstab Kernbereich, RAG Deutsche Steinkohle AG, Herne (Germany); Weiss, Hans-Juergen [Bergwerk Prosper-Haniel, RAG Deutsche Steinkohle AG, Bottrop (Germany); Kotke, Frank [Elektrotechnik unter Tage, Zentralstab Kernbereich der RAG Deutsche Steinkohle AG, Herne (Germany)

2009-11-05

The improvement of processes specific to mining in the collieries of RAG and the improvement of the ergonomic conditions in the deep coal mining deposits of Germany require a higher degree of automation and control of the processes in progress. A higher degree of automation is also re-quired here for the machinery and systems used. RAG will be consolidating its engineering and research activities in these areas over the coming years. (orig.)

Andragogical Model in Language Training of Mining Specialists

Science.gov (United States)

Bondareva, Evgeniya; Chistyakova, Galina; Kleshevskyi, Yury; Sergeev, Sergey; Stepanov, Aleksey

2017-11-01

Nowadays foreign language competence is one of the main professional skills of mining engineers. Modern competitive conditions require the ability for meeting production challenges in a foreign language from specialists and managers of mining enterprises. This is the reason of high demand on foreign language training/retraining courses. Language training of adult learners fundamentally differs from children and adolescent education. The article describes the features of andragogical learning model. The authors conclude that distance learning is the most productive education form having a number of obvious advantages over traditional (in-class) one. Interactive learning method that involves active engagement of adult trainees appears to be of the greatest interest due to introduction of modern information and communication technologies for distance learning.

Development of decision- making mechanism in engineering design of phased coal mines technical upgrade

Science.gov (United States)

Kulak, V. Yu; Petrova, T. V.; Novichikhin, A. V.

2017-09-01

The approach to a choice of a new mine design and technical upgrade of operating coal mines is substantiated. The choice of the option is made in the following way: the elements of the mine technological system are defined, for each element of the system two levels of costs are allocated - capital and operational; a graph of alternative options of the system is formed by matrix enumeration taking into account the possibility of simultaneous application of different elements, up to 10 000 scenarios are formed; capital and operating costs of options are estimated in the form of coefficients as the cost-to-cost ratio in the base variant, which has already been implemented and the costs of which are already known; ranking of the options at the level of costs and the definition of the 10 preferred are performed. It is established that the application of partial enumeration allows the costs relative to the base variant to be reduced by 10 %; the main constraint of costs reduction is the need to comply with all conditions that ensure industrial safety.

A Global Survey of Deep Underground Facilities; Examples of Geotechnical and Engineering Capabilities, Achievements, Challenges (Mines, Shafts, Tunnels, Boreholes, Sites and Underground Facilities for Nuclear Waste and Physics R&D): A Guide to Interactive Global Map Layers, Table Database, References and Notes

International Nuclear Information System (INIS)

Tynan, Mark C.; Russell, Glenn P.; Perry, Frank V.; Kelley, Richard E.; Champenois, Sean T.

2017-01-01

These associated tables, references, notes, and report present a synthesis of some notable geotechnical and engineering information used to create four interactive layer maps for selected: 1) deep mines and shafts; 2) existing, considered or planned radioactive waste management deep underground studies or disposal facilities 3) deep large diameter boreholes, and 4) physics underground laboratories and facilities from around the world. These data are intended to facilitate user access to basic information and references regarding “deep underground” facilities, history, activities, and plans. In general, the interactive maps and database provide each facility’s approximate site location, geology, and engineered features (e.g.: access, geometry, depth, diameter, year of operations, groundwater, lithology, host unit name and age, basin; operator, management organization, geographic data, nearby cultural features, other). Although the survey is not comprehensive, it is representative of many of the significant existing and historical underground facilities discussed in the literature addressing radioactive waste management and deep mined geologic disposal safety systems. The global survey is intended to support and to inform: 1) interested parties and decision makers; 2) radioactive waste disposal and siting option evaluations, and 3) safety case development applicable to any mined geologic disposal facility as a demonstration of historical and current engineering and geotechnical capabilities available for use in deep underground facility siting, planning, construction, operations and monitoring.

A Global Survey of Deep Underground Facilities; Examples of Geotechnical and Engineering Capabilities, Achievements, Challenges (Mines, Shafts, Tunnels, Boreholes, Sites and Underground Facilities for Nuclear Waste and Physics R&D): A Guide to Interactive Global Map Layers, Table Database, References and Notes

Energy Technology Data Exchange (ETDEWEB)

Tynan, Mark C. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Russell, Glenn P. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Perry, Frank V. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kelley, Richard E. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Champenois, Sean T. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-06-13

These associated tables, references, notes, and report present a synthesis of some notable geotechnical and engineering information used to create four interactive layer maps for selected: 1) deep mines and shafts; 2) existing, considered or planned radioactive waste management deep underground studies or disposal facilities 3) deep large diameter boreholes, and 4) physics underground laboratories and facilities from around the world. These data are intended to facilitate user access to basic information and references regarding “deep underground” facilities, history, activities, and plans. In general, the interactive maps and database provide each facility’s approximate site location, geology, and engineered features (e.g.: access, geometry, depth, diameter, year of operations, groundwater, lithology, host unit name and age, basin; operator, management organization, geographic data, nearby cultural features, other). Although the survey is not comprehensive, it is representative of many of the significant existing and historical underground facilities discussed in the literature addressing radioactive waste management and deep mined geologic disposal safety systems. The global survey is intended to support and to inform: 1) interested parties and decision makers; 2) radioactive waste disposal and siting option evaluations, and 3) safety case development applicable to any mined geologic disposal facility as a demonstration of historical and current engineering and geotechnical capabilities available for use in deep underground facility siting, planning, construction, operations and monitoring.

Implementing of action plans for risk communication on the uranium mining sites remedy at Ningyo-Toge Environmental Engineering Center

International Nuclear Information System (INIS)

Yabuta, Naohiro; Kawai, Jun; Hikawa, Tamae

2005-02-01

On the closure of uranium production facilities, settled at Ningyo-Toge Environmental Engineering Center and other area in Okayama and Tottori prefectures, action plans for risk communication with residence and local governments were developed and implemented. With the direction of the action plans for risk communication, 'Imaging plan for developing the local area around Ningyo-Toge' were drawn. Furthermore, practical program called Ethnography by High School Students' were developed, which draw the outlines of past and future around Ningyo-Toge with the insights of high school students, and conducted. As the fundamental materials required to conduct the program above, the topography of northern part of Okayama prefecture, the history and cultures of Kamisaibara village, the history of the uranium mining sites at Ningyo-Toge and Japanese nuclear energy development were clarified. Furthermore, Emergency management plans during pursuing of risk communication plans were also developed. (author)

Screening and prioritisation of chemical risks from metal mining operations, identifying exposure media of concern.

Science.gov (United States)

Pan, Jilang; Oates, Christopher J; Ihlenfeld, Christian; Plant, Jane A; Voulvoulis, Nikolaos

2010-04-01

Metals have been central to the development of human civilisation from the Bronze Age to modern times, although in the past, metal mining and smelting have been the cause of serious environmental pollution with the potential to harm human health. Despite problems from artisanal mining in some developing countries, modern mining to Western standards now uses the best available mining technology combined with environmental monitoring, mitigation and remediation measures to limit emissions to the environment. This paper develops risk screening and prioritisation methods previously used for contaminated land on military and civilian sites and engineering systems for the analysis and prioritisation of chemical risks from modern metal mining operations. It uses hierarchical holographic modelling and multi-criteria decision making to analyse and prioritise the risks from potentially hazardous inorganic chemical substances released by mining operations. A case study of an active platinum group metals mine in South Africa is used to demonstrate the potential of the method. This risk-based methodology for identifying, filtering and ranking mining-related environmental and human health risks can be used to identify exposure media of greatest concern to inform risk management. It also provides a practical decision-making tool for mine acquisition and helps to communicate risk to all members of mining operation teams.

The role of EPFL to Lorraine's post-mining program

International Nuclear Information System (INIS)

Charpentier, D.

2004-01-01

A century of mining and industry has left scars that make it harder to reconstruct a satisfying economy and environment in northern Lorraine's iron-and-steel and coal basins. For this reason, the French state and Lorraine region are supporting redevelopment in these areas. A special 'post-mining' section in the fourth state/region contract foresees exceptional outlays. The experience acquired since 1986 by the EPFL (land public authority of Lorraine) in handling former industrial sites, recycling real estate and dealing with urban wastelands has led the state and region to rely on it for implementing this program. The EPFL has thus become a financial partner and operator under several headings of the aforementioned section: treating blighted areas; polluted sites and soil; connecting mining basins to other areas; operations for re-shaping the landscape; a pole in environmental engineering; the territorial dynamics of border areas; the search for a large zone for installing business; and real estate reserved for re-housing victims. (author)

Connecting traditional sciences with the OLAP and data mining paradigms

Science.gov (United States)

Guergachi, Aziz A.

2003-03-01

The paradigms of OLAP, multidimensional modeling and data mining have first emerged in the areas of market analysis and finance to address various needs of people working in these areas. Does this mean that they are useful and applicable in these areas only? Or, can they also be applicable in the other more traditional areas of science and engineering? What characterize the systems for which these paradigms are suitable? What are the goals of these paradigms? How do they relate to the traditional body of knowledge that has been developed throughout the centuries in the areas of mathematics, statistics, systems science and engineering? Where, how and to what extent can we leverage the conventional wisdom that has been accumulated in the aforementioned disciplines to develop a foundational basis for the above paradigms? The goal of this paper is to address these questions at the foundational level. We argue that the paradigms of OLAP, multidimensional modeling and data mining can also be applied successfully to complex engineering systems, such as membrane-based water/wastewater treatment plants, for example. We develop mathematically-based axiomatic definition of the concepts of 'dimension,' 'dimension level,' 'dimension hierarchy' and 'measure' using set theory and equivalence relations.

Shale Failure Mechanics and Intervention Measures in Underground Coal Mines: Results From 50 Years of Ground Control Safety Research

Science.gov (United States)

2015-01-01

Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining. PMID:26549926

Treatment of mine-water from decommissioning uranium mines

International Nuclear Information System (INIS)

Fan Quanhui

2002-01-01

Treatment methods for mine-water from decommissioning uranium mines are introduced and classified. The suggestions on optimal treatment methods are presented as a matter of experience with decommissioned Chenzhou Uranium Mine

Utilization of geothermal energy in the mining and processing of tungsten ore. Final report

Energy Technology Data Exchange (ETDEWEB)

Erickson, M.V.; Lacy, S.B.; Lowe, G.D.; Nussbaum, A.M.; Walter, K.M.; Willens, C.A.

1981-01-01

The engineering, economic, and environmental feasibility of the use of low and moderate temperature geothermal heat in the mining and processing of tungsten ore is explored. The following are covered: general engineering evaluation, design of a geothermal energy system, economics, the geothermal resource, the institutional barriers assessment, environmental factors, an alternate geothermal energy source, and alternates to geothermal development. (MHR)

Determination of radon and progeny concentrations in Brazilian underground mines

International Nuclear Information System (INIS)

Fraenkel, Mario O.; Gouvea, Vandir de Azevedo; Macacini, Jose F.; Cardozo, Katia; Carvalho Filho, Carlos A. de; Lima, Carlos E.

2008-01-01

The aim of this work is to present the activities related to the determination of radon and progeny concentrations in underground mines in Brazil. Radon is originated from decay of radium-226 and radium-228 present in rocks. Radon and its short-lived progeny can be retained in the workers pulmonary alveoli, and this way they bring about cancer risk to these mining professionals. The occurrence of high radon concentrations in underground coal and copper mines and the lack of systematic survey motivated CNEN, the regulatory agency, to develop the Radon Project, aiming to aid the formulation of a specific regulation with occupational dose limits consistent with international standards recommended by the International Atomic Energy Agency (IAEA). Dozens of underground mines are currently in operation in the national. It had to be noted that about 50% of these mines are located in Minas Gerais province, and for this reason it was chosen to start the Project. In each underground mine it is installed in selected points passive nuclear track etch radon detectors, type LEXAN and Cr-39, for periods from three to five months. It was also made local measurements with Dose Man Pro detectors from SARAD. The points are chosen according to geological features, radiometric activity and characteristics of prospect development. The determination of radon present in mines has been made in IEN (Nuclear Engineering Institute)/Rio de Janeiro-RJ, LAPOC (Pocos de Caldas Laboratory)/Pocos de Caldas-MG e ESPOA (Porto Alegre Office)/Porto Alegre-RS. Until now it was visited about 35 mines in a universe of about 50 mines, from which 20% showed concentration values higher than international limits (ICRP 65), between 500 and 1500 Bq.m -3 . (author)

Engineer exchanging project on coal mine technology field in fiscal 1999. International information exchanging project (advance survey on North America); 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Jizen chosa (Hokubei)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This project has been performed with an intention of making visiting surveys and information collection at coal related organizations in overseas coal producing countries on production technology levels and trends. The project is intended to serve for improvement in the contents of and smooth execution of the engineer exchange project in the 'coal mine technology field. It was carried out by the site surveys. The surveys revealed that the situation of the American coal industry is expected of stable increase in the demand and supply in the future, but the coal price is on the falling trend, and therefore, the industry is compelled to further increase the intensity and enhance the productivity. The industry is strongly influenced by the amended air pollution prevention act and nature destruction problems, hence further coal mine curtailment is estimated. Under such a background, it was found that the long-wall mining process progressing toward larger scale and higher productivity, and the high-wall mining process that provides higher productivity at lower cost and has less impact on the environmental problems can continue development in mountainous areas, particularly in the Appalachian area. The high-wall mining process mines coal at exposed facings on the side of a mountain by using a continuous miner, and transports the coal using machines. (NEDO)

Noise pollution in opencast mines - its impact on human environment

International Nuclear Information System (INIS)

Tripathy, D.P.; Patnaik, N.K.

1994-01-01

Noise could be defined as sound without agreeable musical quality or as unwanted sound. The problem of noise has been accentuated in the mining industry due to increased mechanisation. In opencast mines, noise is generated in almost all the mining operations, becoming thereby an integral part of the mining environment. Prolonged exposure to high levels of noise (>90dBA) proves harmful and may culminate in NIHL. Noise may also bring about other physiological disorders which could lead to irritability and lowering of efficiency. Before initiating any administrative, engineering and medical measures against the noise hazards, noise surveys are essential. They help in identifying the noise pollution sources and quantifying the risk exposures of workers. Effective antinoise measures can accordingly be formulated and implemented. The present paper discusses the results of noise studies in a limestone and dolomite quarry and analyses the SPL (dBA) produced by different machinery in this mine. Further, it focuses on the adverse effects of noise and lists the instruments available for noise monitoring. It also presents the noise standards recommended in India and abroad and suggests the noise abatement strategies to be adopted for protecting the workers against NHL. 7 refs., 2 figs., 6 tabs., 1 app

An ISU study of asteroid mining

Science.gov (United States)

Burke, J. D.

During the 1990 summer session of the International Space University, 59 graduate students from 16 countries carried out a design project on using the resources of near-earth asteroids. The results of the project, whose full report is now available from ISU, are summarized. The student team included people in these fields: architecture, business and management, engineering, life sciences, physical sciences, policy and law, resources and manufacturing, and satellite applications. They designed a project for transporting equipment and personnel to a near-earth asteroid, setting up a mining base there, and hauling products back for use in cislunar space. In addition, they outlined the needed precursor steps, beginning with expansion of present ground-based programs for finding and characterizing near-earth asteroids and continuing with automated flight missions to candidate bodies. (To limit the summer project's scope the actual design of these flight-mission precursors was excluded.) The main conclusions were that asteroid mining may provide an important complement to the future use of lunar resources, with the potential to provide large amounts of water and carbonaceous materials for use off earth. However, the recovery of such materials from presently known asteroids did not show an economic gain under the study assumptions; therefore, asteroid mining cannot yet be considered a prospective business.

30 CFR 77.1712 - Reopening mines; notification; inspection prior to mining.

Science.gov (United States)

2010-07-01

... to mining. 77.1712 Section 77.1712 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... prior to mining. Prior to reopening any surface coal mine after it has been abandoned or declared... an authorized representative of the Secretary before any mining operations in such mine are...

Longwall mining and surface deformation – lessons learned from dInSAR measurements

CSIR Research Space (South Africa)

Engelbrecht, Jeanine

2016-08-01

Full Text Available including 1) subsidence related to mining and groundwater abstraction, 2) deformation following earthquake events, 3) monitoring of landslides and slope stability, 4) monitoring the stability of infrastructure and large engineering works, and 5) monitoring...

Impact of offshore placer mining experiments (PLAMEX) on the sediment size and heavy minerals

Digital Repository Service at National Institute of Oceanography (India)

Valsangkar, A.B.; Fernandes, D.

Two offshore placer mining experiments (PLAMEX) were conducted using submersible pumps specially designed by Central Mechanical Engineering Research Institute (CMERI), Durgapur (India) at 8 m water depth in Kalbadevi Bay (PLAMEX-I), Ratnagiri...

Environmental impact of solution mining for uranium

International Nuclear Information System (INIS)

Hunkin, G.G.

1975-01-01

Compared with most other mining systems, uranium solution mining has a negligible effect on such environmental factors as surface disturbance, interference with natural groundwater quality and distribution, and aerial discharge of radionuclides. The following topics are discussed: the process, personnel safety and health, tailings disposal, impact on groundwater, operating licenses and controls, legislation, and economics. It is concluded that engineered well systems and controlled input/production flow rates, combined with full recirculation systems that maintain constant fluid volumes in the mineralized formations, result in containment of leach solutions within the operating area. The very dilute leach solutions, compatible with natural groundwaters, ensure that no environmental damage results, even if a loss of control occurred. Reduction in the number of processing steps and virtual elimination of operator hazards, waste disposal and land rehabilitation costs help in reducing overall costs

A summary paper on nuclear mining

Energy Technology Data Exchange (ETDEWEB)

Michaelson, S D [Kennecott Copper Corporation, Metal Mining Division, Salt Lake City, UT (United States)

1970-05-15

Fifteen years ago a handful of men began to dream of the potentials of nuclear energy in peaceful applications. In 1957, AEC's Plowshare program was organized to promote and coordinate the work which might convert the dreams into realities. Then, some specific ideas for using nuclear energy in mining were set down in meaningful detail and with reasonable thought. In the 12 years of the Plowshare program nuclear energy concepts for mining have been developed in increasing detail and for a fairly broad range of possible applications. Although it may seem, at times, that progress is slow and month-to-month achievements almost nonexistent, a closer look throws a somewhat different light on the picture. In the first 7 years of Plowshare, from 1957 through 1964, the most obvious mining applications were delineated. These included the use of nuclear explosives to break ore for block caving, for in-situ leaching, and for stripping overburden from large low-grade deposits. Although numerous variations of these applications have been proposed in recent years, these three basic concepts still appear to hold the greatest potential. During those same seven years a number of DOD and Plowshare tests, involving both conventional and nuclear explosives, were conducted so that the phenomena and parameters bearing on mining applications could be evaluated in addition to acquiring other data. The tests, such as Projects Gnome, Sedan, Hard Hat and Danny Boy, have been discussed and reported at these and other meetings, and it would be redundant to review them now. Suffice it to say that from these tests and related work in AEC laboratories, scaling laws for relating yield, crater size, chimney size, fracture extent, and rock types were largely confirmed. Chimney rubble size distribution was determined and contamination problems were evaluated. Aside from these findings, however, the most important development during that 7-year period was the policy that relevant engineering data would

A summary paper on nuclear mining

International Nuclear Information System (INIS)

Michaelson, S.D.

1970-01-01

Fifteen years ago a handful of men began to dream of the potentials of nuclear energy in peaceful applications. In 1957, AEC's Plowshare program was organized to promote and coordinate the work which might convert the dreams into realities. Then, some specific ideas for using nuclear energy in mining were set down in meaningful detail and with reasonable thought. In the 12 years of the Plowshare program nuclear energy concepts for mining have been developed in increasing detail and for a fairly broad range of possible applications. Although it may seem, at times, that progress is slow and month-to-month achievements almost nonexistent, a closer look throws a somewhat different light on the picture. In the first 7 years of Plowshare, from 1957 through 1964, the most obvious mining applications were delineated. These included the use of nuclear explosives to break ore for block caving, for in-situ leaching, and for stripping overburden from large low-grade deposits. Although numerous variations of these applications have been proposed in recent years, these three basic concepts still appear to hold the greatest potential. During those same seven years a number of DOD and Plowshare tests, involving both conventional and nuclear explosives, were conducted so that the phenomena and parameters bearing on mining applications could be evaluated in addition to acquiring other data. The tests, such as Projects Gnome, Sedan, Hard Hat and Danny Boy, have been discussed and reported at these and other meetings, and it would be redundant to review them now. Suffice it to say that from these tests and related work in AEC laboratories, scaling laws for relating yield, crater size, chimney size, fracture extent, and rock types were largely confirmed. Chimney rubble size distribution was determined and contamination problems were evaluated. Aside from these findings, however, the most important development during that 7-year period was the policy that relevant engineering data would

Mining waste contaminated lands: an uphill battle for improving crop productivity

Directory of Open Access Journals (Sweden)

B M Kumar

2013-10-01

Full Text Available Mining drastically alters the physico-chemical and biological environment of the landscape. Low organic matter content, unfavourable pH, low water holding capacity, salinity, coarse texture, compaction, siltation of water bodies due to wash off of mineral overburden dumps, inadequate supply of plant nutrients, accelerated erosion, acid generating materials, and mobilization of contaminated sediments into the aquatic environment are the principal constraints experienced in mining contaminated sites. A variety of approaches have been considered for reclaiming mine wastes including direct revegetation of amended waste materials, top soiling, and the use of capillary barriers. The simplest technology to improve crop productivity is the addition of organic amendments. Biosolids and animal manure can support revegetation, but its rapid decomposition especially in the wet tropics, necessitates repeated applications. Recalcitrant materials such as “biochars”, which improve soil properties on a long term basis as well as promote soil carbon sequestration, hold enormous promise. An eco-friendly and cost-effective Microbe Assisted Phytoremediation system has been proposed to increase biological productivity and fertility of mine spoil dumps. Agroforestry practices may enhance the nutrient status of degraded mine spoil lands (facilitation. N-fixing trees are important in this respect. Metal tolerant ecotypes of grasses and calcium-loving plants help restore lead, zinc, and copper mine tailings and gypsum mine spoils, respectively. Overall, an integrated strategy of introduction of metal tolerant plants, genetic engineering for enhanced synthesis and exudation of natural chelators into the rhizosphere, improvement of rhizosphere, and integrated management including agroforestry will be appropriate for reclaiming mining contaminated lands.

Data mining and knowledge discovery for big data methodologies, challenge and opportunities

CERN Document Server

2014-01-01

The field of data mining has made significant and far-reaching advances over the past three decades.  Because of its potential power for solving complex problems, data mining has been successfully applied to diverse areas such as business, engineering, social media, and biological science. Many of these applications search for patterns in complex structural information. In biomedicine for example, modeling complex biological systems requires linking knowledge across many levels of science, from genes to disease.  Further, the data characteristics of the problems have also grown from static to dynamic and spatiotemporal, complete to incomplete, and centralized to distributed, and grow in their scope and size (this is known as big data). The effective integration of big data for decision-making also requires privacy preservation. The contributions to this monograph summarize the advances of data mining in the respective fields. This volume consists of nine chapters that address subjects ranging from mining da...

Acid mine drainage: mining and water pollution issues in British Columbia

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-31

The importance of protecting water quality and some of the problems associated with mineral development are described. Negative impacts of mining operations such as sedimentation, water disturbances, and water pollution from waste rock and tailings are considered. Mining wastes, types of water pollution from mining, the legacy of acid mine drainage, predicting acid mine drainage, preventing and mitigating acid mine drainage, examples from the past, and cyanide heap-leaching are discussed. The real costs of mining at the Telkwa open pit coal mine are assessed. British Columbia mines that are known for or are potentially acid generating are shown on a map. 32 refs., 10 figs.

Responsible Mining: A Human Resources Strategy for Mine Development Project

OpenAIRE

Sampathkumar, Sriram (Ram)

2012-01-01

Mining is a global industry. Most mining companies operate internationally, often in remote, challenging environments and consequently frequently have respond to unusual and demanding Human Resource (HR) requirements. It is my opinion that the strategic imperative behind success in mining industry is responsible mining. The purpose of this paper is to examine how an effective HR strategy can be a competitive advantage that contributes to the success of a mining project in the global mining in...

Environmental restoration of uranium mines in Canada: Progress over 52 years

International Nuclear Information System (INIS)

Feasby, D.G.

1997-01-01

In Canada, the technology for disposal of uranium mine wastes and reclamation of mines has evolved over a period of 52 years. Early practice involved dumping untreated wastes into the nearest depression or lake and leaving rock and infrastructure in place. Now, the practice is to deposit chemically-stabilized tailings, waste rock and building rubble into highly engineered waste management facilities or mine openings. Similarly the ''footprint'' of the mining activity has been reduced to a very small area and the site is restored as-close-as-possible to pre-mining status. This paper describes the evolution of disposal and reclamation methods and the criteria which have determined the development path followed. Remediation techniques to bring older and now unacceptable tailings deposits into satisfactory compliance with current regulations are reviewed. Some monitoring results are presented. All of the uranium mines in Elliot Lake, Ontario, a large uranium producer since 1957, are now permanently closed. Considerable progress has been made on decommissioning the tailings areas by developing long term maintenance of water covers on some, and water treatment plants and stable soil covers on the others. The innovative methods being used to develop the water covers are described, along with the challenges remaining. Methods now under development in Saskatchewan for subaqueous deposition of paste tailings for permanent disposal in mined out open pits are also described. This method will provide for the first time, ''walkaway'', meaning no long term monitoring and maintenance will be required

Use of Data Mining to Reveal Body Mass Index (BMI): Patterns among Pennsylvania Schoolchildren, Pre-K to Grade 12

Science.gov (United States)

YoussefAgha, Ahmed H.; Lohrmann, David K.; Jayawardene, Wasantha P.

2013-01-01

Background: Health eTools for Schools was developed to assist school nurses with routine entries, including height and weight, on student health records, thus providing a readily accessible data base. Data-mining techniques were applied to this database to determine if clinically signi?cant results could be generated. Methods: Body mass index…

Profitability and occupational injuries in U.S. underground coal mines.

Science.gov (United States)

Asfaw, Abay; Mark, Christopher; Pana-Cryan, Regina

2013-01-01

. We found an inverse relationship between profitability and each of the three indicators of occupational injuries we used. These results might be partially due to factors that affect both profitability and safety, such as management or engineering practices, and partially due to lower investments in safety by less profitable mines, which could imply that some financially stressed mines might be so focused on survival that they forgo investing in safety. Published by Elsevier Ltd.

Extending mine life

International Nuclear Information System (INIS)

Anon.

1984-01-01

Mine layouts, new machines and techniques, research into problem areas of ground control and so on, are highlighted in this report on extending mine life. The main resources taken into account are coal mining, uranium mining, molybdenum and gold mining

Sense of ownership and evaluation of safety. Questionnaire survey for reclamation project in the uranium mine

International Nuclear Information System (INIS)

Ishizaka, Kaoru; Gofuku, Akio; Tanaka, Masaru; Tokizawa, Takayuki; Sato, Kazuhiko; Koga, Osamu

2010-01-01

To obtain public understanding on the uranium mining sites reclamation at Ningyo-toge Environmental Engineering Center, it is necessary to conduct appropriate Risk Communication (RC). In this study, to discuss the appropriate Risk communication method on the uranium mining sites reclamation, we conducted questionnaire survey and SEM analysis. The results of the pass analysis are as follows: (1) in the group which has high-sense of ownership, risk acceptance has a strong impact on sense of security for uranium mining sites reclamation, (2) in the group which shows low-sense of ownership, hatred for radioactive ray has a strong impact relatively. (author)

Assessment of shaft safety and management system of controlling engineering information

Energy Technology Data Exchange (ETDEWEB)

Liu Rui-xin; Xu Yan-chun [Yanzhou Mining Group Ltd., Zoucheng (China)

2008-02-15

Evaluating shaft safety and establishing a system for controlling engineering information is very important because more than 90 shafts in thick alluvial areas suddenly have shaft wall fracturing or breaking problems and there are more than a few hundred shafts of similar geologic conditions. Taking shaft control in the Yangzhou Coal Mining Group as an example, an assessment and management system and related software were established. This system includes basic information of the mine, measurement results and analysis, and functions of empirical and theoretical forecasting and finite element analysis, which are confirmed to be very effective for guiding shaft well control engineering in practice. 8 refs., 3 figs., 2 tabs.

Application of data mining techniques for nuclear data and instrumentation

International Nuclear Information System (INIS)

Toshniwal, Durga

2013-01-01

Data mining is defined as the discovery of previously unknown, valid, novel, potentially useful, and understandable patterns in large databases. It encompasses many different techniques and algorithms which differ in the kinds of data that can be analyzed and the form of knowledge representation used to convey the discovered knowledge. Patterns in the data can be represented in many different forms, including classification rules, association rules, clusters, etc. Data mining thus deals with the discovery of hidden trends and patterns from large quantities of data. The field of data mining is emerging as a new, fundamental research area with important applications to science, engineering, medicine, business, and education. It is an interdisciplinary research area and draws upon several roots, including database systems, machine learning, information systems, statistics and expert systems. Data mining, when performed on time series data, is known as time series data mining (TSDM). A time series is a sequence of real numbers, each number representing a value at a point of time. During the past few years, there has been an explosion of research in the area of time series data mining. This includes attempts to model time series data, to design languages to query such data, and to develop access structures to efficiently process queries on such data. Time series data arises naturally in many real-world applications. Efficient discovery of knowledge through time series data mining can be helpful in several domains such as: Stock market analysis, Weather forecasting etc. An important application area of data mining techniques is in nuclear power plant and related data. Nuclear power plant data can be represented in form of time sequences. Often it may be of prime importance to analyze such data to find trends and anomalies. The general goals of data mining include feature extraction, similarity search, clustering and classification, association rule mining and anomaly

Situation of radioactive wastes and their prevention and treatment measures in China's uranium mining and metallurgy

International Nuclear Information System (INIS)

Li Renjie.

1988-01-01

The sorts of radioactive wastes produced in uranium mining and metallurgy and their hazards are discribed in this paper. The characteristics of the radioactive wastes are discussed. The measurements and results are introduced for treatment and disposal of the radioactive wastes. The way to deal with prevention and treatment of radioactive wastes is presented in the stages of engineering design, construction, production and decommission of uranium mines and plants

Kempe's engineers year-book for 1977. Volume II

Energy Technology Data Exchange (ETDEWEB)

Prockter, C.E. (ed.)

1977-01-01

The second volume of this two-volume yearbook contains data on: electrical and electronic engineering; aerodynamics and aircraft propulsion; gas turbines; internal combustion engines; motor vehicles; fuels; fluidics; nuclear energy; gas and gas engineering; steam engineering and steam turbines; marine diesel engines; naval architecture; mining engineering; industrial explosives; air compression, pneumatic equipment, etc.; refrigeration, heating, ventilation and air conditioning; lighting; industrial safety and protection; fire protection; highway engineering; surveying; foundation and earthwork; cements, mortars and clay products; buildings; public health engineering; concretes; design of steel structures; bridges and bridgework; paints and coatings; patents, designs and trade marks; depreciation; legal notes for engineers; factory planning and layout; and agricultural engineering. (1325p.) A subject index is provided. (LCL)

Radiological modeling software for underground uranium mines

International Nuclear Information System (INIS)

Bjorndal, B.; Moridi, R.

1999-01-01

The Canadian Institute for Radiation Safety (CAIRS) has developed computer simulation software for modeling radiological parameters in underground uranium mines. The computer program, called 3d RAD, allows radiation protection professionals and mine ventilation engineers to quickly simulate radon and radon progeny activity concentrations and potential alpha energy concentrations in complex mine networks. The simulation component of 3d RAD, called RSOLVER, is an adaptation of an existing modeling program called VENTRAD, originally developed at Queen's University, Ontario. Based on user defined radiation source terms and network physical properties, radiological parameters in the network are calculated iteratively by solving Bateman's Equations in differential form. The 3d RAD user interface was designed in cooperation with the Canada Centre for Mineral and Energy Technology (CANMET) to improve program functionality and to make 3d RAD compatible with the CANMET ventilation simulation program, 3d CANVENT. The 3d RAD program was tested using physical data collected in Canadian uranium mines. 3d RAD predictions were found to agree well with theoretical calculations and simulation results obtained from other modeling programs such as VENTRAD. Agreement with measured radon and radon progeny levels was also observed. However, the level of agreement was found to depend heavily on the precision of source term data, and on the measurement protocol used to collect radon and radon progeny levels for comparison with the simulation results. The design and development of 3d RAD was carried out under contract with the Saskatchewan government

Data mining teaching throughout cards game competition

OpenAIRE

Antoñanzas-Torres, Javier; Urraca, Ruben; Sodupe-Ortega, Enrique; Martínez-de-Pison, Francisco; Pernía-Espinoza, Alpha

2015-01-01

[EN] Data-mining techniques and statistical metrics learning can be complicated because of the complexity and overwhelming nature of this field. In this paper a class competition to improve learning of designing Decision Support Systems (DSS) by playing a classic cards game named "Copo" is proposed. The fact that this game is based on a probabilistic problem and that different solutions can be obtained represents a very typical kind of problem in the field of engineering and compu...

International MultiConference of Engineers and Computer Scientists 2015

CERN Document Server

Ao, Sio-Iong; Huang, Xu; Castillo, Oscar

2016-01-01

This volume comprises selected extended papers written by prominent researchers participating in the International MultiConference of Engineers and Computer Scientists 2015, Hong Kong, 18-20 March 2015. The conference served as a platform for discussion of frontier topics in theoretical and applied engineering and computer science, and subjects covered include communications systems, control theory and automation, bioinformatics, artificial intelligence, data mining, engineering mathematics, scientific computing, engineering physics, electrical engineering, and industrial applications. The book describes the state-of-the-art in engineering technologies and computer science and its applications, and will serve as an excellent reference for industrial and academic researchers and graduate students working in these fields.

MONITORING OF MINING

Directory of Open Access Journals (Sweden)

Berislav Šebečić

1996-12-01

Full Text Available The way mining was monitored in the past depended on knowledge, interest and the existing legal regulations. Documentary evidence about this work can be found in archives, libraries and museums. In particular, there is the rich archival material (papers and books concerning the work of the one-time Imperial and Royal Mining Captaincies in Zagreb, Zadar, Klagenfurt and Split, A minor part of the documentation has not yet been transferred to Croatia. From mining handbooks and books we can also find out about mining in Croatia. In the context of Austro-Hungary. For example, we can find out that the first governorships in Zagreb and Zadar headed the Ban, Count Jelacic and Baron Mamula were also the top mining authorities, though this, probably from political motives, was suppressed in the guides and inventories or the Mining Captaincies. At the end of the 1850s, Croatia produced 92-94% of sea salt, up to 8.5% of sulphur, 19.5% of asphalt and 100% of oil for the Austro-Hungarian empire. From data about mining in the Split Mining Captaincy, prepared for the Philadephia Exhibition, it can be seen that in the exploratory mining operations in which there were 33,372 independent mines declared in 1925 they were looking mainly for bauxite (60,0%, then dark coal (19,0%, asphalts (10.3% and lignites (62%. In 1931, within the area covered by the same captaincy, of 74 declared mines, only 9 were working. There were five coal mines, three bauxite mines and one for asphalt. I suggest that within state institution, the Mining Captaincy or Authority be renewed, or that a Mining and Geological Authority be set ap, which would lead to the more complete affirmation of Croatian mining (the paper is published in Croatian.

Challenges of safety in Indian mines during twenty-first century

Energy Technology Data Exchange (ETDEWEB)

Batra, S.C. [Directorate General of Mines Safety, Dhanbad (India)

1997-12-31

Mining industry in India has been progressing steadily during the last five decades. Production of coal, limestone, iron ore, bauxite, copper, lead and zinc ores has gone up several times during this period. Ambitious production targets have been set for the years to come. With depletion of easily mineable deposits, mining activities would have to be extended to difficult geo-mining locales like greater depth and geologically disturbed areas. Extension of workings to deeper horizons would give rise to problems and mechanisation would introduce hazards like accidental fires, electrocution, environmental pollution by internal combustion engines, generation of dust, noise and vibration. The mining industry will have to prepare itself right from now to meet the challenges of safety and health problems. Thus strategies will have to be evolved to solve problems of strata control including slope stability, ventilation, hazards of explosions etc. Timber supports would have to be phased out and be replaced by steel supports. Disasters and their prevention would need a fresh look. Communication, human resource development and management information system are the other areas needing attention. 10 refs., 1 tab., 2 app.

Gold-Mining

DEFF Research Database (Denmark)

Raaballe, J.; Grundy, B.D.

2002-01-01

  Based on standard option pricing arguments and assumptions (including no convenience yield and sustainable property rights), we will not observe operating gold mines. We find that asymmetric information on the reserves in the gold mine is a necessary and sufficient condition for the existence...... of operating gold mines. Asymmetric information on the reserves in the mine implies that, at a high enough price of gold, the manager of high type finds the extraction value of the company to be higher than the current market value of the non-operating gold mine. Due to this under valuation the maxim of market...

The mining methods at the Fraisse mine

International Nuclear Information System (INIS)

Heurley, P.; Vervialle, J.P.

1985-01-01

The Fraisse mine is one of the four underground mines of the La Crouzille mining divisions of Cogema. Faced with the necessity to mechanize its workings, this mine also had to satisfy a certain number of stringent demands. This has led to concept of four different mining methods for the four workings at present in active operation at this pit, which nevertheless preserve the basic ideas of the methods of top slicing under concrete slabs (TSS) or horizontal cut-and-fill stopes (CFS). An electric scooptram is utilized. With this type of vehicle the stringent demands for the introduction of means for fire fighting and prevention are reduced to a minimum. Finally, the dimensions of the vehicles and the operation of these methods result in a net-to-gross tonnages of close to 1, i.e. a maximum output, combined with a minimum of contamination [fr

Process Mining Methodology for Health Process Tracking Using Real-Time Indoor Location Systems

Science.gov (United States)

Fernandez-Llatas, Carlos; Lizondo, Aroa; Monton, Eduardo; Benedi, Jose-Miguel; Traver, Vicente

2015-01-01

The definition of efficient and accurate health processes in hospitals is crucial for ensuring an adequate quality of service. Knowing and improving the behavior of the surgical processes in a hospital can improve the number of patients that can be operated on using the same resources. However, the measure of this process is usually made in an obtrusive way, forcing nurses to get information and time data, affecting the proper process and generating inaccurate data due to human errors during the stressful journey of health staff in the operating theater. The use of indoor location systems can take time information about the process in an unobtrusive way, freeing nurses, allowing them to engage in purely welfare work. However, it is necessary to present these data in a understandable way for health professionals, who cannot deal with large amounts of historical localization log data. The use of process mining techniques can deal with this problem, offering an easily understandable view of the process. In this paper, we present a tool and a process mining-based methodology that, using indoor location systems, enables health staff not only to represent the process, but to know precise information about the deployment of the process in an unobtrusive and transparent way. We have successfully tested this tool in a real surgical area with 3613 patients during February, March and April of 2015. PMID:26633395

Process Mining Methodology for Health Process Tracking Using Real-Time Indoor Location Systems.

Science.gov (United States)

Fernandez-Llatas, Carlos; Lizondo, Aroa; Monton, Eduardo; Benedi, Jose-Miguel; Traver, Vicente

2015-11-30

The definition of efficient and accurate health processes in hospitals is crucial for ensuring an adequate quality of service. Knowing and improving the behavior of the surgical processes in a hospital can improve the number of patients that can be operated on using the same resources. However, the measure of this process is usually made in an obtrusive way, forcing nurses to get information and time data, affecting the proper process and generating inaccurate data due to human errors during the stressful journey of health staff in the operating theater. The use of indoor location systems can take time information about the process in an unobtrusive way, freeing nurses, allowing them to engage in purely welfare work. However, it is necessary to present these data in a understandable way for health professionals, who cannot deal with large amounts of historical localization log data. The use of process mining techniques can deal with this problem, offering an easily understandable view of the process. In this paper, we present a tool and a process mining-based methodology that, using indoor location systems, enables health staff not only to represent the process, but to know precise information about the deployment of the process in an unobtrusive and transparent way. We have successfully tested this tool in a real surgical area with 3613 patients during February, March and April of 2015.

2nd International Conference on Soft Computing and Data Mining

CERN Document Server

Ghazali, Rozaida; Nawi, Nazri; Deris, Mustafa

2017-01-01

This book provides a comprehensive introduction and practical look at the concepts and techniques readers need to get the most out of their data in real-world, large-scale data mining projects. It also guides readers through the data-analytic thinking necessary for extracting useful knowledge and business value from the data. The book is based on the Soft Computing and Data Mining (SCDM-16) conference, which was held in Bandung, Indonesia on August 18th–20th 2016 to discuss the state of the art in soft computing techniques, and offer participants sufficient knowledge to tackle a wide range of complex systems. The scope of the conference is reflected in the book, which presents a balance of soft computing techniques and data mining approaches. The two constituents are introduced to the reader systematically and brought together using different combinations of applications and practices. It offers engineers, data analysts, practitioners, scientists and managers the insights into the concepts, tools and techni...

Use of a remotely piloted aircraft system for hazard assessment in a rocky mining area (Lucca, Italy)

Science.gov (United States)

Salvini, Riccardo; Mastrorocco, Giovanni; Esposito, Giuseppe; Di Bartolo, Silvia; Coggan, John; Vanneschi, Claudio

2018-01-01

The use of remote sensing techniques is now common practice in different working environments, including engineering geology. Moreover, in recent years the development of structure from motion (SfM) methods, together with rapid technological improvement, has allowed the widespread use of cost-effective remotely piloted aircraft systems (RPAS) for acquiring detailed and accurate geometrical information even in evolving environments, such as mining contexts. Indeed, the acquisition of remotely sensed data from hazardous areas provides accurate 3-D models and high-resolution orthophotos minimizing the risk for operators. The quality and quantity of the data obtainable from RPAS surveys can then be used for inspection of mining areas, audit of mining design, rock mass characterizations, stability analysis investigations and monitoring activities. Despite the widespread use of RPAS, its potential and limitations still have to be fully understood.In this paper a case study is shown where a RPAS was used for the engineering geological investigation of a closed marble mine area in Italy; direct ground-based techniques could not be applied for safety reasons. In view of the re-activation of mining operations, high-resolution images taken from different positions and heights were acquired and processed using SfM techniques to obtain an accurate and detailed 3-D model of the area. The geometrical and radiometrical information was subsequently used for a deterministic rock mass characterization, which led to the identification of two large marble blocks that pose a potential significant hazard issue for the future workforce. A preliminary stability analysis, with a focus on investigating the contribution of potential rock bridges, was then performed in order to demonstrate the potential use of RPAS information in engineering geological contexts for geohazard identification, awareness and reduction.

Use of a remotely piloted aircraft system for hazard assessment in a rocky mining area (Lucca, Italy

Directory of Open Access Journals (Sweden)

R. Salvini

2018-01-01

Full Text Available The use of remote sensing techniques is now common practice in different working environments, including engineering geology. Moreover, in recent years the development of structure from motion (SfM methods, together with rapid technological improvement, has allowed the widespread use of cost-effective remotely piloted aircraft systems (RPAS for acquiring detailed and accurate geometrical information even in evolving environments, such as mining contexts. Indeed, the acquisition of remotely sensed data from hazardous areas provides accurate 3-D models and high-resolution orthophotos minimizing the risk for operators. The quality and quantity of the data obtainable from RPAS surveys can then be used for inspection of mining areas, audit of mining design, rock mass characterizations, stability analysis investigations and monitoring activities. Despite the widespread use of RPAS, its potential and limitations still have to be fully understood.In this paper a case study is shown where a RPAS was used for the engineering geological investigation of a closed marble mine area in Italy; direct ground-based techniques could not be applied for safety reasons. In view of the re-activation of mining operations, high-resolution images taken from different positions and heights were acquired and processed using SfM techniques to obtain an accurate and detailed 3-D model of the area. The geometrical and radiometrical information was subsequently used for a deterministic rock mass characterization, which led to the identification of two large marble blocks that pose a potential significant hazard issue for the future workforce. A preliminary stability analysis, with a focus on investigating the contribution of potential rock bridges, was then performed in order to demonstrate the potential use of RPAS information in engineering geological contexts for geohazard identification, awareness and reduction.

Survey of Analysis of Crime Detection Techniques Using Data Mining and Machine Learning

Science.gov (United States)

Prabakaran, S.; Mitra, Shilpa

2018-04-01

Data mining is the field containing procedures for finding designs or patterns in a huge dataset, it includes strategies at the convergence of machine learning and database framework. It can be applied to various fields like future healthcare, market basket analysis, education, manufacturing engineering, crime investigation etc. Among these, crime investigation is an interesting application to process crime characteristics to help the society for a better living. This paper survey various data mining techniques used in this domain. This study may be helpful in designing new strategies for crime prediction and analysis.

Attenuation of mining-derived pollutants in the hyporheic zone. A review

International Nuclear Information System (INIS)

Gandy, C.J.; Jarvis, A.P.; Smith, J.W.N.

2007-01-01

Mine water pollution is a major cause of surface- and groundwater pollution in former mining districts throughout Europe. It is a potential barrier to achieving good status water bodies, which is a requirement of the EU Water Framework Directive. In the UK, a concerted effort has been made over the last decade or so to address the scientific and practical challenges relating to the remediation of mine water pollution. However, most of this work has focused on remediation of point sources of pollution (typically arising from abandoned mines and shafts), while the behaviour of mine water at the groundwater-surface water interface (the 'hyporheic zone') has received far less attention in relevant scientific and engineering literature. The extent of mine water pollution and capacity for its attenuation at the hyporheic zone has not been well quantified while, furthermore, the complex chemical and microbial processes occurring there (specifically with reference to mining-derived pollutants) have not been investigated in any depth. The absence of such data may relate, in a large part, to the difficulty in physically measuring volumes and concentrations associated with these river inputs/exports. A far greater body of literature addresses biogeochemical processes at the hyporheic zone (especially relating to manganese), albeit many such articles relate to aqueous metal dynamics in general, rather than mine water specifically. This paper presents a review of the natural attenuation processes that may limit the movement and availability of mining-derived pollutants at the groundwater-surface water (GW-SW) interface, and specifically within the hyporheic zone. A substantial part focuses on precipitation and adsorption processes at the hyporheic zone, as well as discussing the role of microbial processes in governing metal ion mobility. (author)

Attenuation of mining-derived pollutants in the hyporheic zone. A review

Energy Technology Data Exchange (ETDEWEB)

Gandy, C.J.; Jarvis, A.P. [Hydrogeochemical Engineering Research and Outreach (HERO), Institute for Research on Environment and Sustainability, Newcastle University, Newcastle upon Tyne, NE1 7RU (United Kingdom); Smith, J.W.N. [Environment Agency, Science Group, Solihull, West Midlands, B92 7HX (United Kingdom); Catchment Science Centre, Sheffield University, Kroto Research Institute, Sheffield, S3 7HQ (United Kingdom)

2007-02-15

Mine water pollution is a major cause of surface- and groundwater pollution in former mining districts throughout Europe. It is a potential barrier to achieving good status water bodies, which is a requirement of the EU Water Framework Directive. In the UK, a concerted effort has been made over the last decade or so to address the scientific and practical challenges relating to the remediation of mine water pollution. However, most of this work has focused on remediation of point sources of pollution (typically arising from abandoned mines and shafts), while the behaviour of mine water at the groundwater-surface water interface (the 'hyporheic zone') has received far less attention in relevant scientific and engineering literature. The extent of mine water pollution and capacity for its attenuation at the hyporheic zone has not been well quantified while, furthermore, the complex chemical and microbial processes occurring there (specifically with reference to mining-derived pollutants) have not been investigated in any depth. The absence of such data may relate, in a large part, to the difficulty in physically measuring volumes and concentrations associated with these river inputs/exports. A far greater body of literature addresses biogeochemical processes at the hyporheic zone (especially relating to manganese), albeit many such articles relate to aqueous metal dynamics in general, rather than mine water specifically. This paper presents a review of the natural attenuation processes that may limit the movement and availability of mining-derived pollutants at the groundwater-surface water (GW-SW) interface, and specifically within the hyporheic zone. A substantial part focuses on precipitation and adsorption processes at the hyporheic zone, as well as discussing the role of microbial processes in governing metal ion mobility. (author)

Migration: a concept analysis from a nursing perspective.

Science.gov (United States)

Freeman, Michelle; Baumann, Andrea; Blythe, Jennifer; Fisher, Anita; Akhtar-Danesh, Noori

2012-05-01

  This article is a report of a concept analysis of nurse migration.   International migration is increasing and nurse migrants are active participants in this movement. Migration is a complex term and can be examined from a range of perspectives. Analysis of nurse migration is needed to guide policy, practice and research.   A literature search was undertaken using electronic literature indexes, specific journals and websites, internet search engines and hand searches. No timeframe was placed on the search. Most literature found was published between 2001 and 2009. A sample of 80 documents met the inclusion criteria.   Walker and Avant's approach guided the analysis.   Nurse migration can be defined by five attributes: the motivation and decisions of individuals; external barriers and facilitators; freedom of choice to migrate; freedom to migrate as a human right, and dynamic movement. Antecedents of migration include the political, social, economic, legal, historical and educational forces that comprise the push and pull framework. The consequences of migration are positive or negative depending on the viewpoint and its affect on the individual and other stakeholders such as the source country, destination country, healthcare systems and the nursing profession.   This concept analysis clarified the complexities surrounding nurse migration. A nursing-specific middle-range theory was proposed to guide the understanding and study of nurse migration. © 2011 Blackwell Publishing Ltd.

The nursing contribution to chronic disease management: a discussion paper.

Science.gov (United States)

Forbes, Angus; While, Alison

2009-01-01

This paper explores the nature of the nursing contribution to chronic disease management (CDM) and identifies a number of key nursing activities within CDM both at the individual patient and care system levels. The activities were identified following a detailed review of the literature (160 reports and studies of nursing practice) relating to three tracer disorders: diabetes, chronic obstructive pulmonary disease and multiple sclerosis. The paper examines these activities collectively to generate models expressing some of the core functions of nursing within CDM. The paper illustrates some of the changing characteristics of nursing roles within CDM. More fundamentally, the paper questions the position of nursing in relation to the technologies that define CDM systems and proposes four levels of contribution: the nurse as technology; the nurse as technologist; the nurse as system engineer; and the nurse as architect. These different levels reflect distinctions in the nature of the nursing gaze and power relations within the health care workforce. The paper also highlights how nurses are failing to develop the evidence for their practice in CDM. The paper concludes that there is a need for some clear principles to guide clinical practice and encourage innovation in CDM. It is argued that the principles should not be rule-bound but define a distinctive nursing gaze that will position the nursing profession within the health care system and in relation to other professions. The gaze should incorporate the needs of the individual patient and the care system that they inhabit.

Garzweiler II opencast mine - balance of interests between ecology and economy

International Nuclear Information System (INIS)

Hartung, M.

1994-01-01

In the region including the three cities of Cologne, Aachen and Moenchengladbach the brown coal reserves amount to 55 Gt, of which about 7 Gt are located in the areas Bergheim, Inden, Hambach and Garzweiler in licensed opencast mines or in planned field extensions, with an overburden-to-coal ratio of less than 5.6:1. Favourable preconditions for profitable winning of the brown coal are created by the deposit conditions. At present, the yearly output lies between 105 and 110 Mt, of which about 85% are used to generate electricity, whilst 15% are supplied to the thermal energy market. In order to maintain the same coal output as hitherto, it is absolutely essential that winning should continue in the noth of the Rhineland mining area, that is in the Garzweiler II opencast mine extension. After extensive preliminary exploration the licensing procedure for this opencast mine commenced in 1987. Assuming that the procedure continues smoothly, it is anticipated that the crown coal development plan will be approved by the spring of 1995. With a project such as that of the Garzweiler II opencast mine different interests are involved. On the one hand, interest is focussed on a reliable and cheap supply of energy, on economically successful brown coal mining and on job security in the future. On the other hand, the planned opencast mine constitutes an encroachment of limited duration on a specific living space, economic region and natural environment. From the example of Garzweiler II it is clearly evident that the brown coal mining industry by adopting entirely new and highly efficient engineering techniques is making a significant contribution towards establishing a balance of interests. (orig.) [de

Mined-out land

International Nuclear Information System (INIS)

Reinsalu, Enno; Toomik, Arvi; Valgma, Ingo

2002-01-01

Estonian mineral resources are deposited in low depth and mining fields are large, therefore vast areas are affected by mining. There are at least 800 deposits with total area of 6,000 km 2 and about the same number of underground mines, surface mines, peat fields, quarries, and sand and gravel pits. The deposits cover more than 10% of Estonian mainland. The total area of operating mine claims exceeds 150 km 2 that makes 0.3 % of Estonian area. The book is written mainly for the people who are living or acting in the area influenced by mining. The observations and research could benefit those who are interested in geography and environment, who follow formation and look of mined-out landscapes. The book contains also warnings for careless people on and under the surface of the mined-out land. Part of the book contains results of the research made in 1968-1993 by the first two authors working at the Estonian branch of A.Skochinsky Institute of Mining. Since 1990, Arvi Toomik continued this study at the Northeastern section of the Institute of Ecology of Tallinn Pedagogical University. Enno Reinsalu studied aftereffects of mining at the Mining Department of Tallinn Technical University from 1998 to 2000. Geographical Information System for Mining was studied by Ingo Valgma within his doctoral dissertation, and this book is one of the applications of his study

Trust Mines

Science.gov (United States)

The United States and the Navajo Nation entered into settlement agreements that provide funds to conduct investigations and any needed cleanup at 16 of the 46 priority mines, including six mines in the Northern Abandoned Uranium Mine Region.

Using the method of mathematical-logical modeling in compiling an engineering plan for development of a mine

Energy Technology Data Exchange (ETDEWEB)

Fajkos, A.; Klimek, M.

1980-01-01

A possibility of using a mathematical-logical modeling to improve the quality of mine shaft operation planning in Czechloslovakia based on the example of the Sverma mine in Ostrova with complex mining-geological conditions is studied. For the basic criteria we assumed: extraction plant, number of shifts in the long walls, time period for beginning and ending long wall operation, processing of reserves with consideration of existing conditions, output and dip angle of a formation, quality of extracted coal, and also: time intervals for processing separate formations, limitation of extraction load in a long wall in connection with gas emission, timbering, the necessity of insuring normal operating conditions, concentration of extraction, time relationship of preparatory and extraction operations.

Instream sand and gravel mining: Environmental issues and regulatory process in the United States

Science.gov (United States)

Meador, M.R.; Layher, A.O.

1998-01-01

Sand and gravel are widely used throughout the U.S. construction industry, but their extraction can significantly affect the physical, chemical, and biological characteristics of mined streams. Fisheries biologists often find themselves involved in the complex environmental and regulatory issues related to instream sand and gravel mining. This paper provides an overview of information presented in a symposium held at the 1997 midyear meeting of the Southern Division of the American Fisheries Society in San Antonio, Texas, to discuss environmental issues and regulatory procedures related to instream mining. Conclusions from the symposium suggest that complex physicochemical and biotic responses to disturbance such as channel incision and alteration of riparian vegetation ultimately determine the effects of instream mining. An understanding of geomorphic processes can provide insight into the effects of mining operations on stream function, and multidisciplinary empirical studies are needed to determine the relative effects of mining versus other natural and human-induced stream alterations. Mining regulations often result in a confusing regulatory process complicated, for example, by the role of the U.S. Army Corps of Engineers, which has undergone numerous changes and remains unclear. Dialogue among scientists, miners, and regulators can provide an important first step toward developing a plan that integrates biology and politics to protect aquatic resources.

Web Mining

Science.gov (United States)

Fürnkranz, Johannes

The World-Wide Web provides every internet citizen with access to an abundance of information, but it becomes increasingly difficult to identify the relevant pieces of information. Research in web mining tries to address this problem by applying techniques from data mining and machine learning to Web data and documents. This chapter provides a brief overview of web mining techniques and research areas, most notably hypertext classification, wrapper induction, recommender systems and web usage mining.

Data mining, mining data : energy consumption modelling

Energy Technology Data Exchange (ETDEWEB)

Dessureault, S. [Arizona Univ., Tucson, AZ (United States)

2007-09-15

Most modern mining operations are accumulating large amounts of data on production and business processes. Data, however, provides value only if it can be translated into information that appropriate users can utilize. This paper emphasized that a new technological focus should emerge, notably how to concentrate data into information; analyze information sufficiently to become knowledge; and, act on that knowledge. Researchers at the Mining Information Systems and Operations Management (MISOM) laboratory at the University of Arizona have created a method to transform data into action. The data-to-action approach was exercised in the development of an energy consumption model (ECM), in partnership with a major US-based copper mining company, 2 software companies, and the MISOM laboratory. The approach begins by integrating several key data sources using data warehousing techniques, and increasing the existing level of integration and data cleaning. An online analytical processing (OLAP) cube was also created to investigate the data and identify a subset of several million records. Data mining algorithms were applied using the information that was isolated by the OLAP cube. The data mining results showed that traditional cost drivers of energy consumption are poor predictors. A comparison was made between traditional methods of predicting energy consumption and the prediction formed using data mining. Traditionally, in the mines for which data were available, monthly averages of tons and distance are used to predict diesel fuel consumption. However, this article showed that new information technology can be used to incorporate many more variables into the budgeting process, resulting in more accurate predictions. The ECM helped mine planners improve the prediction of energy use through more data integration, measure development, and workflow analysis. 5 refs., 11 figs.

Mining with communities

International Nuclear Information System (INIS)

Veiga, Marcello M.; Scoble, Malcolm; McAllister, Mary Louise

2001-01-01

To be considered as sustainable, a mining community needs to adhere to the principles of ecological sustainability, economic vitality and social equity. These principles apply over a long time span, covering both the life of the mine and post-mining closure. The legacy left by a mine to the community after its closure is emerging as a significant aspect of its planning. Progress towards sustainability is made when value is added to a community with respect to these principles by the mining operation during its life cycle. This article presents a series of cases to demonstrate the diverse potential challenges to achieving a sustainable mining community. These case studies of both new and old mining communities are drawn mainly from Canada and from locations abroad where Canadian companies are now building mines. The article concludes by considering various approaches that can foster sustainable mining communities and the role of community consultation and capacity building. (author)

Ideate about building green mine of uranium mining and metallurgy

International Nuclear Information System (INIS)

Shi Zuyuan

2012-01-01

Analysing the current situation of uranium mining and metallurgy; Setting up goals for green uranium mining and metallurgy, its fundamental conditions, Contents and measures. Putting forward an idea to combine green uranium mining and metallurgy with the state target for green mining, and keeping its own characteristics. (author)

Social big data mining

CERN Document Server

Ishikawa, Hiroshi

2015-01-01

Social Media. Big Data and Social Data. Hypotheses in the Era of Big Data. Social Big Data Applications. Basic Concepts in Data Mining. Association Rule Mining. Clustering. Classification. Prediction. Web Structure Mining. Web Content Mining. Web Access Log Mining, Information Extraction and Deep Web Mining. Media Mining. Scalability and Outlier Detection.

Nurses who work outside nursing.

Science.gov (United States)

Duffield, Christine; Pallas, Linda O'Brien; Aitken, Leanne M

2004-09-01

The desire to care for people, a family history of professional health care work, and security in career choice are documented reasons for entering nursing. Reasons for leaving include workload, unsafe work environments and harassment. The relationship between these factors and the time nurses spend in the profession has not been explored. This paper reports a study with people who have left nursing, to investigate why they became a nurse, how long they stayed in nursing, and their reasons for leaving. A questionnaire was mailed to Registered Nurses currently working outside nursing, seeking respondents' reasons for entering and leaving nursing, and perceptions of the skills gained from nursing and the ease of adjustment to working in a non-nursing environment. Data analysis included descriptive statistics, exploratory and confirmatory factor analysis, correlational analysis and linear and multiple regression analysis. A model incorporating the factors 'altruistic reasons', 'default choice' and 'stepping stone' explained 36.2% of the variance in reasons for becoming a nurse. A model incorporating the factors 'legal and employer', 'external values and beliefs about nursing', 'professional practice', 'work life/home life' and 'contract requirements' explained 55.4% of the variance in reasons for leaving nursing. Forty-eight per cent of the variance in tenure in nursing practice was explained through personal characteristics of nurses (36%), reasons for becoming a nurse (7%) and reasons for leaving (6%). The reasons why nurses entered or left the profession were varied and complex. While personal characteristics accounted for a large component of tenure in nursing, those managing the nursing workforce should consider professional practice issues and the balance between work life and home life.

Mechatronics in the mining industrie. With (development) method towards success; Mechatronik im Bergbau. Mit (Entwicklungs-) Methode zum Erfolg

Energy Technology Data Exchange (ETDEWEB)

Brandt, Thorsten; Bruckmann, Tobias [Mercatronics GmbH, Duisburg (Germany)

2009-10-01

Germany is a high-wage country. Hence the internationally competitive extraction of raw materials in Germany can only be ensured by highly efficient working processes. Tackling the associated extreme requirements on road-driving, coal winning and transport equipment has resulted in the German mining industry and its suppliers achieving the role of an international leader in technology. To safeguard this position also in the future the successful mechanisation will now be followed by the mechatronisation in the mining industry. Efficiency will be increased by (partial) automation and assistance systems. This contribution is a first step towards a series of articles, which explain the principles of mechatronic development methods in the mining industry and will make the development engineers in the mines aware of the high potential of mechatronics in the mining industry. (orig.)

Mining and mining authorities in Saarland 2016. Mining economy, mining technology, occupational safety, environmental protection, statistics, mining authority activities. Annual report; Bergbau und Bergbehoerden im Saarland 2016. Bergwirtschaft, Bergtechnik, Arbeitsschutz, Umweltschutz, Statistiken, Taetigkeiten der Bergbehoerden. Jahresbericht

Energy Technology Data Exchange (ETDEWEB)

NONE

2016-07-01

The annual report of the Saarland Upper Mining Authority provides an insight into the activities of mining authorities. Especially, the development of the black coal mining, safety and technology of mining as well as the correlation between mining and environment are stressed.

On-Board Mining in the Sensor Web

Science.gov (United States)

Tanner, S.; Conover, H.; Graves, S.; Ramachandran, R.; Rushing, J.

2004-12-01

On-board data mining can contribute to many research and engineering applications, including natural hazard detection and prediction, intelligent sensor control, and the generation of customized data products for direct distribution to users. The ability to mine sensor data in real time can also be a critical component of autonomous operations, supporting deep space missions, unmanned aerial and ground-based vehicles (UAVs, UGVs), and a wide range of sensor meshes, webs and grids. On-board processing is expected to play a significant role in the next generation of NASA, Homeland Security, Department of Defense and civilian programs, providing for greater flexibility and versatility in measurements of physical systems. In addition, the use of UAV and UGV systems is increasing in military, emergency response and industrial applications. As research into the autonomy of these vehicles progresses, especially in fleet or web configurations, the applicability of on-board data mining is expected to increase significantly. Data mining in real time on board sensor platforms presents unique challenges. Most notably, the data to be mined is a continuous stream, rather than a fixed store such as a database. This means that the data mining algorithms must be modified to make only a single pass through the data. In addition, the on-board environment requires real time processing with limited computing resources, thus the algorithms must use fixed and relatively small amounts of processing time and memory. The University of Alabama in Huntsville is developing an innovative processing framework for the on-board data and information environment. The Environment for On-Board Processing (EVE) and the Adaptive On-board Data Processing (AODP) projects serve as proofs-of-concept of advanced information systems for remote sensing platforms. The EVE real-time processing infrastructure will upload, schedule and control the execution of processing plans on board remote sensors. These plans

75 FR 17529 - High-Voltage Continuous Mining Machine Standard for Underground Coal Mines

Science.gov (United States)

2010-04-06

... High-Voltage Continuous Mining Machine Standard for Underground Coal Mines AGENCY: Mine Safety and... of high-voltage continuous mining machines in underground coal mines. It also revises MSHA's design...-- Underground Coal Mines III. Section-by-Section Analysis A. Part 18--Electric Motor-Driven Mine Equipment and...

Interface management for the Mined Geologic Disposal System

International Nuclear Information System (INIS)

Ashlock, K.J.

1998-03-01

The purpose of this paper is to present the interface management process that is to be used for Mined Geologic Disposal System (MGDS) development. As part of the systems engineering and integration performed on the Yucca Mountain Project (YMP), interface management is critical in the development of the potential MGDS. The application of interface management on the YMP directly addresses integration between physical elements of the MGDS and the organizations responsible for their development

Diesel engine emission deterioration - a preliminary study

CSIR Research Space (South Africa)

Pretorius, Cecilia J

2016-04-01

Full Text Available The objective of this study was to find a parameter in diesel and oil analysis of underground mining vehicles that can be correlated with personal diesel particulate matter (DPM) exposure and used as part of an engine maintenance programme. A number...

Computerized system of team make-up and work allocation in the Belgian Zolder mine

Energy Technology Data Exchange (ETDEWEB)

Rustanowicz, M.

1979-01-01

System of work allocation introduced in 1974 in the Zolder Coal Mine (NV Kempense Steenkolenmijnen) in Belgium is evaluated. The system is based on an IBM 370/158 computer. An information management system supervises the programing work. There are approximately 30 programs. Absenteeism in the Belgian coal mines is generally high at approximately 24% and some months as high as 40%. Therefore, introducing a computerized system of work allocation and team make-up was advantageous. Operation of the system is described on the levels of foreman, engineers and director of the mine. Advantages of the system are numerous. It enables optimization of team make-up and work allocation, shortens the time of allocation of work by a foreman, increases efficiency of foremen's work and provides the director with the means and information necessary for efficient decision making in improving the productivity of the mine. (5 refs.) (In Polish)

Mine water treatment

Energy Technology Data Exchange (ETDEWEB)

Komissarov, S V

1980-10-01

This article discusses composition of chemical compounds dissolved or suspended in mine waters in various coal basins of the USSR: Moscow basin, Kuzbass, Pechora, Kizelovsk, Karaganda, Donetsk and Chelyabinsk basins. Percentage of suspended materials in water depending on water source (water from water drainage system of dust suppression system) is evaluated. Pollution of mine waters with oils and coli bacteria is also described. Recommendations on construction, capacity of water settling tanks, and methods of mine water treatment are presented. In mines where coal seams 2 m or thicker are mined a system of two settling tanks should be used: in the upper one large grains are settled, in the lower one finer grains. The upper tank should be large enough to store mine water discharged during one month, and the lower one to store water discharged over two months. Salty waters from coal mines mining thin coal seams should be treated in a system of water reservoirs from which water evaporates (if climatic conditions permit). Mine waters from mines with thin coal seams but without high salt content can be treated in a system of long channels with water plants, which increase amount of oxygen in treated water. System of biological treatment of waste waters from mine wash-houses and baths is also described. Influence of temperature, sunshine and season of the year on efficiency of mine water treatment is also assessed. (In Russian)

Engineering Students' Views of Corporate Social Responsibility: A Case Study from Petroleum Engineering.

Science.gov (United States)

Smith, Jessica M; McClelland, Carrie J; Smith, Nicole M

2017-12-01

The mining and energy industries present unique challenges to engineers, who must navigate sometimes competing responsibilities and codes of conduct, such as personal senses of right and wrong, professional ethics codes, and their employers' corporate social responsibility (CSR) policies. Corporate social responsibility (CSR) is the current dominant framework used by industry to conceptualize firms' responsibilities to their stakeholders, yet has it plays a relatively minor role in engineering ethics education. In this article, we report on an interdisciplinary pedagogical intervention in a petroleum engineering seminar that sought to better prepare engineering undergraduate students to critically appraise the strengths and limitations of CSR as an approach to reconciling the interests of industry and communities. We find that as a result of the curricular interventions, engineering students were able to expand their knowledge of the social, rather than simply environmental and economic dimensions of CSR. They remained hesitant, however, in identifying the links between those social aspects of CSR and their actual engineering work. The study suggests that CSR may be a fruitful arena from which to illustrate the profoundly sociotechnical dimensions of the engineering challenges relevant to students' future careers.

Uranium mining

International Nuclear Information System (INIS)

2008-01-01

Full text: The economic and environmental sustainability of uranium mining has been analysed by Monash University researcher Dr Gavin Mudd in a paper that challenges the perception that uranium mining is an 'infinite quality source' that provides solutions to the world's demand for energy. Dr Mudd says information on the uranium industry touted by politicians and mining companies is not necessarily inaccurate, but it does not tell the whole story, being often just an average snapshot of the costs of uranium mining today without reflecting the escalating costs associated with the process in years to come. 'From a sustainability perspective, it is critical to evaluate accurately the true lifecycle costs of all forms of electricity production, especially with respect to greenhouse emissions, ' he says. 'For nuclear power, a significant proportion of greenhouse emissions are derived from the fuel supply, including uranium mining, milling, enrichment and fuel manufacture.' Dr Mudd found that financial and environmental costs escalate dramatically as the uranium ore is used. The deeper the mining process required to extract the ore, the higher the cost for mining companies, the greater the impact on the environment and the more resources needed to obtain the product. I t is clear that there is a strong sensitivity of energy and water consumption and greenhouse emissions to ore grade, and that ore grades are likely to continue to decline gradually in the medium to long term. These issues are critical to the current debate over nuclear power and greenhouse emissions, especially with respect to ascribing sustainability to such activities as uranium mining and milling. For example, mining at Roxby Downs is responsible for the emission of over one million tonnes of greenhouse gases per year and this could increase to four million tonnes if the mine is expanded.'

Geophysical applications for oil sand mine tailings management

Energy Technology Data Exchange (ETDEWEB)

Parker, D.; Bauman, P. [WorleyParsons, Calgary, AB (Canada)

2009-07-01

Geophysical techniques are applied throughout a mine's life cycle to facilitate siting, constructing and monitoring of tailings dumps and ponds. This presentation described 3 case studies from the Athabasca region in northeast Alberta that demonstrated some of the concerns associated with oil sand mine tailings, and the information that geophysical surveys can provide. The objectives of these studies were to determine the lateral and depth extents of elevated conductivities of soil and groundwater that have high salt concentration from the tailings sand pore fluid. Due to high chloride concentrations within the tailings material, salt within the root zone may affect vegetation. A terrain conductivity survey was designed to map the lateral extents of salinity impact, while an electrical resistivity tomography (ERT) survey was used to delineate the tailings sand leachate at depth. The proper management of oil sand tailings facilities is vital to the life cycle of a mine. It was concluded that geophysical techniques can be instrumental in managing several engineering and environmental challenges, from Pleistocene channel mapping, to tailings pond settling characteristics, to reclaiming tailings sands. 1 ref., 7 figs.

Internet technologies in the mining industry. Towards unattended mining systems

Energy Technology Data Exchange (ETDEWEB)

Krzykawski, Michal [FAMUR Group, Katowice (Poland)

2009-08-27

Global suppliers of longwall systems focus mainly on maximising the efficiency of the equipment they manufacture. Given the fact that, since 2004, coal demand on world markets has been constantly on the increase, even during an economic downturn, this endeavour seems fully justified. However, it should be remembered that maximum efficiency must be accompanied by maximum safety of all underground operations. This statement is based on the belief that the mining industry, which exploits increasingly deep and dangerous coal beds, faces the necessity to implement comprehensive IT systems for managing all mining processes and, in the near future, to use unmanned mining systems, fully controllable from the mine surface. The computerisation of mines is an indispensable element of the development of the world mining industry, a belief which has been put into practice with e-mine, developed by the FAMUR Group. (orig.)

Application of a cross-pit bridge conveyor system in mining

Energy Technology Data Exchange (ETDEWEB)

Zeindler, R.W. (Krupp Canada Inc., Calgary, Alberta); Fawcett, D.A.

1981-04-01

A summary is presented of the report completed by the Coal Mining Research Centre in 1980. This report was of a cross-pit conveyor system applied as an auxillary mining complement to the major stripping unit, a dragline. The purpose of the CMRC report was to evaluate selective mining and replacement of the upper horizons of the strata as an aid in reclamation. These strata were the topsoil, subsoil and glacial till. Past utilization of cross-pit conveyor systems and related engineering studies were assessed. The parameters of the study were based on the mining and geological conditions of the Alberta prairie coal mines. The principal excavator for stripping was a dragline. Excavation of the upper horizons was done by a bucket-wheel excavator discharging onto the cross-pit conveyor. Alternative equipment applications were economically compared. Four cases or geological sections were evaluated in detail. The economics of the alternative mining systems for each of the cases were determined. In all instances, the most economical solution was a tandem system utilizing a dragline with a bucket-wheel excavator/cross-pit conveyor system. For both the CMRC study and a similar US paper, the application of a tandem system provided the lowest annual ownership and operating costs. The tandem system consists of a dragline excavating and casting the majority of the waste or overburden and a BWE/CPCS selectively excavating and replacing the topsoil, subsoil and part of the unconsolidated overburden. The bridge spans and designs are within known technical and economic limits.

Mudstone depressurization behaviour in an open pit coal mine, Indonesia

Energy Technology Data Exchange (ETDEWEB)

Marchand, G.; Waterhouse, J. [Golder Associates, West Perth, WA (Australia); Crisostomo, J. [PT Adaro Indonesia, Jakarta (Indonesia)

2010-07-01

Mining activities in the Tutupan mine in Indonesia began in the mid-1990s. The open pit mine's coal seams are interbedded with fine-grained sandstones, mudstones, and carbonaceous mudstones. Slope stability analyses at the pit have integrated hydrogeology with geotechnical engineering analyses to optimize slope designs and reduce the risk of slope failure. This paper discussed the impact of mining and dewatering on mudstone depressurization. Sensors were placed at key points in the mine to obtain data related to the mudstone units. Reductions in pore pressure occurred as a result of groundwater flow away from the observed zones, increases in porosity, and increases in total porosity caused by an expansion of the rock mass as a result of drainage and hydrostatic unloading. Mudstone pore pressure trends with time were interpreted by determining the thickness of the mudstone unit, the presence or absence of known thin sandstone beds, unloading from overhead mining activities, and the position of the mudstone within the sedimentary sequence. The study showed that unloading activities have a significant impact on pore pressure in thick mudstone units, regardless of the depth, thickness, or properties of the unit. Pore pressure within high wall mudstone units typically decreased to values equivalent to the elevation of the unit where it was exposed to dips in a high wall. The dewatering of sandstone units in low walls caused a decline in pore pressure within the thick mudstone units located beneath the sandstones. Differences in primary permeabilities were attributed to greater fracturing in deeper and stronger rock units. 3 refs., 4 figs.

Project development for mining-metallurgical complexes for production of uranium concentrates - an analysis and a methodology

International Nuclear Information System (INIS)

Ajuria G, S.; Blanco P, B.; Pena A, J.; Manzanera Q, C.

1978-10-01

Activities comprising the development of a project for a mining-metallurgical complex for production of uranium concentrates, from sampling and evaluation of an orebody until plant start-up, are analyzed. The analysis of the orebody, characterization of the ore, bench scale and pilot plant metallurgical studies, environmental studies and economic analyses of the project are described. The mining project and mine preparation and engineering and construction of the plant are reviewed in less detail. The estimated time lapse for the development of a typical project under ideal conditions is 66 months. A bar diagram is included showing an approximate timetable for each activity. (author)

Sustainable lignite mining and utilization. Developments in the Rhenish lignite-mining area; Nachhaltige Braunkohlegewinnung und -nutzung. Entwicklung im Rheinischen Revier

Energy Technology Data Exchange (ETDEWEB)

Gaertner, Dieter [RWE Power AG, Bergheim (Germany). Sparte Tagebaue

2012-09-15

Lignite is an essential module in the Rhenish mining area's economic power. Mini ng in a densely populated region like the Rhineland calls for keeping an eye equ ally on people, the environment and industry now and in the future. By considering all concerns and ensuring transparency in our approach to people, we have succeeded in obtaining public acceptance also for large-scale projects in an environment that is not always easy in Germany. RWE Power plans to use lignite in powe r generation and in upgrading operations for many decades to come, so that the company is systematically implementing the power-plant renewal programme with is planning for BoAplus as highly efficient next-generation lignite-based power plants. Research on CO{sub 2} utilization, flexibilization, energy storage and alternative uses of lignite are as much features of RWE Power's future-proof alignment in the Rhenish mining area as are further innovations in the opencast mines. Core aspects here include further automation in the deployment of main mine equipment, closely dovetailed with innovations in other operating units. Parallel restructuring of the operating units and the Lignite Approvals area are underpinning these measures. Innovations and their translation into technical progress will ensure the success of a measured energy turnaround both in Germany and throughout Europe. However, this requires dependable political conditions, so that an engineering spirit can go on being transformed into entrepreneurial action. (orig.)

Nurse Continuity and Hospital-Acquired Pressure Ulcers: A Comparative Analysis Using an Electronic Health Record "Big Data" Set.

Science.gov (United States)

Stifter, Janet; Yao, Yingwei; Lodhi, Muhammad Kamran; Lopez, Karen Dunn; Khokhar, Ashfaq; Wilkie, Diana J; Keenan, Gail M

2015-01-01

Little research demonstrating the association between nurse continuity and patient outcomes exists despite an intuitive belief that continuity makes a difference in care outcomes. The aim of this study was to examine the association of nurse continuity with the prevention of hospital-acquired pressure ulcers (HAPU). A secondary use of data from the Hands on Automated Nursing Data System (HANDS) was performed for this comparative study. The HANDS is a nursing plan of care data set containing 42,403 episodes documented by 787 nurses, on nine units, in four hospitals and includes nurse staffing and patient characteristics. The HANDS data set resides in a "big data" relational database consisting of 89 tables and 747 columns of data. Via data mining, we created an analytic data set of 840 care episodes, 210 with and 630 without HAPUs, matched by nursing unit, patient age, and patient characteristics. Logistic regression analysis determined the association of nurse continuity and additional nurse-staffing variables on HAPU occurrence. Poor nurse continuity (unit mean continuity index = .21-.42 [1.0 = optimal continuity]) was noted on all nine study units. Nutrition, mobility, perfusion, hydration, and skin problems on admission, as well as patient age, were associated with HAPUs (p data, showing that it offers rich potential for future study of nurse continuity and its effect on patient outcomes.

Mapping and monitoring coal mine subsidence using LiDAR and InSAR

Energy Technology Data Exchange (ETDEWEB)

Froese, C.R.; Mei, S. [Alberta Geological Survey, Edmonton, AB (Canada). Energy Resources Conservation Board

2008-07-01

In the early 1900s, the abandonment of coal mines in Alberta was not regulated and closure documentation was poor. Although the general locations of mines are known, the locations of the specific adits and shafts are not. As such, there are many cases in southwestern Alberta where infrastructure was built on top of old coal mine workings without any detailed records of the abandoned mine or displacement monitoring. The crowns of these workings have been subject to ongoing strain that is reflected at the surface. The rate at which the strain is progressing prior to collapse is not well understood. Mitigation of collapse events is site specific and reactive. This paper demonstrated that airborne LiDAR and spaceborne InSAR technologies can provide valuable information on the distribution of abandoned underground coal mine workings. Both remote sensing techniques were used on Turtle Mountain in the Crowsnest Pass to obtain quantitative information on landslide mechanics, including the patterns and rate of ground movement and subsidence. These techniques can be used to map the location of surface collapse and delineate the location of the coal mine workings that were not previously documented. It was concluded that these technologies will likely become more readily available in the future and incorporated into geo-engineering practices for use in ground hazard detection, monitoring and management. 8 refs., 6 figs.

Improving Technological Competency in Nursing Students: The Passport Project

Directory of Open Access Journals (Sweden)

Julie Edwards

2011-07-01

Full Text Available Integration of informatics competency into a nursing curriculum is important to ensure success throughout the education and career of contemporary nursing students. As enrollment in nursing programs increases, the diverse population of students from many different cultural and socioeconomic backgrounds presents a challenge for faculty in addressing unique learning needs. Competency in informatics will allow the beginning nursing student to navigate the on-line teaching software used by colleges. With rigorous expectations in nursing programs, students may feel overwhelmed with assignments, organization, and time management. Frustration may build when students struggle with basic informatics competency, often leaving them unable to navigate instructional websites or work with necessary on-line learning content. The purpose of this project, Passport Project for Nursing Success, was to assess the skills, knowledge, and informatics comfort level of students, while providing computer training and teaching for beginning nursing students in an undergraduate nursing program in Central Illinois. The community college encompassed students from a ten county area, with 20 percent of the student population enrolled in the Applied Science curriculum. Initial implementation occurred prior to the students' first nursing course and emphasized basic skills necessary to navigate on-line learning software, library search engines, and electronic communication. The greatest barrier to successful implementation was faculty resistance and academic support during completion of the initial implementation of the Passport Project. Post- project surveys indicated overwhelming student support for the education received and improved retention rates of first semester nursing students.

PREVENTION OF ACID MINE DRAINAGE GENERATION FROM OPEN-PIT MINE HIGHWALLS

Science.gov (United States)

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Available information on the generation of AMD from open-pit mine highwalls is very limit...

Challenges and issues facing the future of nursing education: implications for ethnic minority faculty and students.

Science.gov (United States)

Davis, Sheila P; Davis, Danyetta D

2010-01-01

Current trends in higher education in the United States demand that nursing take stock of how it is prepared or being prepared to face challenges and issues impacting on its future. The intense effort made to attract students to pursue advanced training in science and engineering in the United States pales in comparison to the numbers of science and engineering majors produced yearly in international schools. As a result, more and more jobs are being outsourced to international markets. Could international outsourcing become a method of nursing education? Authors submit that to remain competitive, the nursing profession must attract a younger cohort of technologically savvy students and faculty reflective of the growing diverse population in the United States. Additionally, nursing programs in research universities face even more daunting challenges as it relates to mandates for funded research programs of educational units. This article offers suggestions and recommendations for nursing programs in higher education institutions on ways to attract and retain ethnic minorities and of how to harness the power of research to address burgeoning societal health challenges.

A direction of developing a mining method and mining complexes

Energy Technology Data Exchange (ETDEWEB)

Gabov, V.V.; Efimov, I.A. [St. Petersburg State Mining Institute, St. Petersburg (Russian Federation). Vorkuta Branch

1996-12-31

The analyses of a mining method as a main factor determining the development stages of mining units is presented. The paper suggests a perspective mining method which differs from the known ones by following peculiarities: the direction selectivity of cuts with regard to coal seams structure; the cutting speed, thickness and succession of dusts. This method may be done by modulate complexes (a shield carrying a cutting head for coal mining), their mining devices being supplied with hydraulic drive. An experimental model of the module complex has been developed. 2 refs.

Psychological aspects of accident prevention in mines

Energy Technology Data Exchange (ETDEWEB)

Lukestikova, M

1981-04-01

This paper duscusses ways of preventing work accidents and increasing work safety in underground black coal mines. Specific conditions of underground operations in coal mines are stressed. Elements of work accident prevention are analyzed: reducing hazards by introducing safer technology, automation and mechanization of operations associated with hazards, introducing special measures within the framework of safety engineering. Dependence of accident rate on such factors as personnel training, age, motivation, qualifications, and labor discipline is discussed. Investigations indicate that miner motivation plays a significant role in accident prevention. A high degree of labor motivation successfully reduces accident rate and a low degree of motivation increases accident rate. Role of labor collective in labor motivation as well as a correct system of wage incentives are evaluated. Methods of personnel training aimed at reducing accident rate are described. Role of a technique by which a group of miners attempts to find a solution to a work safety problem by amassing all ideas spontaneously contributed by participants is stressed.

Blending mining and nuclear industries at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Walls, J.R.

1990-01-01

At the Waste Isolation Pilot Plant (WIPP) traditional procedures for underground mining activities have been significantly altered in order to assure underground safety and project adherence to numerous regulatory requirements. Innovative techniques have been developed for WIPP underground procedures, mining equipment, and operating environments. The mining emphasis at WIPP is upon the quality of the excavation, not (as in conventional mines) on the production of ore. The WIPP is a United States Department of Energy (DOE) project that is located 30 miles southeast of Carlsbad, New Mexico, where the nation's first underground engineered nuclear repository is being constructed. The WIPP site was selected because of its location amidst a 607 meter thick salt bed, which provides a remarkably stable rock formation for the permanent storage of nuclear waste. The underground facility is located 655 meters below the earth's surface, in the Salado formation, which comprises two-hundred million year old halites with minor amounts of clay and anhydrites. When completed, the WIPP underground facility will consist of two components: approximately 81 square kilometers of experimental areas, and approximately 405 square kilometers of repository. 3 figs

Does Synergy Exist in Nursing? A Concept Analysis.

Science.gov (United States)

Witges, Kim A; Scanlan, Judith M

2015-01-01

The aim is to analyze the concept of synergy, particularly as the concept applies to teamwork, and determine if the concept has utility in improving the work environment for nurses. Tackling nursing shortages that result from a poor work environment is a priority for many nurse leaders. Producing synergy among teams may be an effective strategy in enhancing the work environment. However, the understanding of synergy and the ability to produce synergy among teams has been seldom highlighted or discussed within nursing literature. Walker and Avant's approach was used to guide this concept analysis of synergy. Literature searches involved databases (PsycInfo, Medline, Cumulative Index for Nursing and Allied Health Literature [CINAHL], and Scopus), Internet search engines (Google), and hand searches. The analysis suggests that synergy is an outcome of the successful collaboration of the following three attributes: group cohesion, the pursuit of a common goal, and the achievement of a positive gain, considerably more than what was thought possible by the group. The foundation for this accomplishment requires an underlying feeling of special importance, the acknowledgment of each member's role, and open communication and dialogue among members. Nursing leaders would benefit from a broader understanding of synergy, and the mindful application and utility of synergy as an outcome of effective teamwork among nurses. © 2014 Wiley Periodicals, Inc.

The effective use of search engines on the Internet.

Science.gov (United States)

Younger, P

This article explains how nurses can get the most out of researching information on the internet using the search engine Google. It also explores some of the other types of search engines that are available. Internet users are shown how to find text, images and reports and search within sites. Copyright issues are also discussed.

30 CFR 780.27 - Reclamation plan: Surface mining near underground mining.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Reclamation plan: Surface mining near underground mining. 780.27 Section 780.27 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL...

Minimizing the Impact of Mining Activities for Sustainable Mined-Out ...

African Journals Online (AJOL)

Minimizing the Impact of Mining Activities for Sustainable Mined-Out Area ... sensing and Geographical Information System (GIS) in assessing environmental impact of ... Keywords: Solid mineral, Impact assessment, Mined-out area utilization, ...

Archveyor{trademark} automated mining system - implementation at the Conant mine

Energy Technology Data Exchange (ETDEWEB)

Hofmann, W.J. [Arch of Illinois, Percy, IL (United States)

1997-12-01

Arch Mineral Corporation, through the Arch Technology Department, has developed an automated continuous haulage mining system called the `Archveyor{trademark}`. The original technology came from a Russian patent. Kloeckner-Becorit (K-B) further developed the system and called it the `Mobile Conveyor`. This system was utilized in both coal and trona mines in the United States and Canada. Consolidation Coal designed their version of this continuous haulage system, called the `Tramveyor`. The Tramveyor is presently operating in their Dilworth Mine, in Pennsylvania. This system has no computer guidance system related to the continuous miner or the Tramveyor. Arch Mineral Corporation has further developed this continuous haulage mining system. Their system is a programmable, logic-controlled (PLC) automated mining system. A highwall version of the Archveyor{trademark} is being operated at Arch of Wyoming near Hanna, Wyoming. This paper introduces the first underground version of Archveyor{trademark} to be implemented at Conant Mine in southern Illinois. During the development process, the Archveyor{trademark} mining system consists of a continuous miner, a bolter car, the Archveyor{trademark} (itself), a stageloader, and an operator`s cab. During the secondary mining process the bolter car is taken out of the system.

Management of dry flue gas desulfurization by-products in underground mines

Energy Technology Data Exchange (ETDEWEB)

Sevim, H.

1997-06-01

Disposal of coal combustion by-products (CCBs) in an environmentally sound manner is a major issue facing the coal and utility industries in the US today. Disposal into abandoned sections of underground coal mines may overcome many of the surface disposal problems along with added benefits such as mitigation of subsidence and acid mine drainage. However, many of the abandoned underground coal mines are located far from power plants, requiring long distance hauling of by-products which will significantly contribute to the cost of disposal. For underground disposal to be economically competitive, the transportation and handling cost must be minimized. This requires careful selection of the system and optimal design for efficient operation. The materials handling and system economics research addresses these issues. Transportation and handling technologies for CCBs were investigated from technical, environmental and economic points of view. Five technologies were found promising: (1) Pneumatic Trucks, (2) Pressure Differential Rail Cars, (3) Collapsible Intermodal Containers, (4) Cylindrical Intermodal Tanks, and (5) Coal Hopper Cars with Automatic Retractable Tarping. The first two technologies are currently being utilized in transporting by-products from power plants to disposal sites, whereas the next three are either in development or in conceptualization phases. In this research project, engineering design and cost models were developed for the first four technologies. The engineering design models are in the form of spreadsheets and serve the purpose of determining efficient operating schedules and sizing of system components.

Economical Recovery of By-products in the Mining Industry

Energy Technology Data Exchange (ETDEWEB)

Berry, J.B.

2001-12-05

The U.S. Department of Energy (DOE) Office of Industrial Technologies, Mining Industry of the Future Program, works with the mining industry to further the industry's advances toward environmental and economic goals. Two of these goals are (1) responsible emission and by-product management and (2) low-cost and efficient production (DOE 1998). DOE formed an alliance with the National Mining Association (NMA) to strengthen the basis for research projects conducted to benefit the mining industry. NMA and industry representatives actively participate in this alliance by evaluating project proposals and by recommending research project selection to DOE. Similarly, the National Research Council (NRC) has recently and independently recommended research and technology development opportunities in the mining industry (NRC 2001). The Oak Ridge National Laboratory (ORNL) and Colorado School of Mines engineers conducted one such project for DOE regarding by -product recovery from mining process residue. The results of this project include this report on mining industry process residue and waste with opportunity for by-product recovery. The U.S. mineral processing industry produces over 30,000,000 metric tons per year of process residue and waste that may contain hazardous species as well as valuable by-products. This study evaluates the copper, lead, and zinc commodity sectors which generate between 23,300,000 and 24,000,000 metric tons per year. The distribution of residual elements in process residues and wastes varies over wide ranges* because of variations in the original ore content as it is extracted from the earth's crust. In the earth's crust, the elements of interest to mining fall into two general geochemical classifications, lithophiles and chalcophiles** (Cox 1997). Groups of elements are almost always present together in a given geochemical classification, but the relative amounts of each element are unique to a particular ore body. This paper

Management of mining-related damages in abandoned underground coal mine areas using GIS

International Nuclear Information System (INIS)

Lee, U.J.; Kim, J.A.; Kim, S.S.; Kim, W.K.; Yoon, S.H.; Choi, J.K.

2005-01-01

The mining-related damages such as ground subsidence, acid mine drainage (AMD), and deforestation in the abandoned underground coal mine areas become an object of public concern. Therefore, the system to manage the mining-related damages is needed for the effective drive of rehabilitation activities. The management system for Abandoned Underground Coal Mine using GIS includes the database about mining record and information associated with the mining-related damages and application programs to support mine damage prevention business. Also, this system would support decision-making policy for rehabilitation and provide basic geological data for regional construction works in abandoned underground coal mine areas. (authors)

Mechanics Evolution Characteristics Analysis of Pressure-arch in Fully-mechanized Mining Field

Directory of Open Access Journals (Sweden)

S.R. Wang

2014-09-01

Full Text Available Based on a practical engineering, the three-dimension computational model was built using FLAC3D under the fullymechanized mining condition. Considering four variation factors, such as the distance of mining advancing, the strength of the surrounding rock, the speed of mining advancing and the dip angle of the coal seam, the mechanics evolution characteristics of the pressure-arch were analyzed. The result showed that for the horizontal seam, the geometric shape of the pressure-arch varied from flat arch to round arch gradually and the height and thickness of the pressure-arch also increased; the maximum principal stress in the skewback also increased with the working face advancing. With the strength of the surrounding rock from soft to hard, the arch thickness reduced, and the arch loading decreased. To improve the mining speed can do some contributions to the stability of the pressure-arch in the mining field. With the increase of dip angle of the seam, the pressure-arch displayed an asymmetric shape, the vault was tilted and moved to the upward direction. At the same time, the thickness of the pressure-arch increased, and the stress concentration in the skewback tended to be further intensified.

Text Mining.

Science.gov (United States)

Trybula, Walter J.

1999-01-01

Reviews the state of research in text mining, focusing on newer developments. The intent is to describe the disparate investigations currently included under the term text mining and provide a cohesive structure for these efforts. A summary of research identifies key organizations responsible for pushing the development of text mining. A section…

Surface mining

Science.gov (United States)

Robert Leopold; Bruce Rowland; Reed Stalder

1979-01-01

The surface mining process consists of four phases: (1) exploration; (2) development; (3) production; and (4) reclamation. A variety of surface mining methods has been developed, including strip mining, auger, area strip, open pit, dredging, and hydraulic. Sound planning and design techniques are essential to implement alternatives to meet the myriad of laws,...

Uranium mining

International Nuclear Information System (INIS)

Lange, G.

1975-01-01

The winning of uranium ore is the first stage of the fuel cycle. The whole complex of questions to be considered when evaluating the profitability of an ore mine is shortly outlined, and the possible mining techniques are described. Some data on uranium mining in the western world are also given. (RB) [de

Cubis AG - for the mining industry and for new markets

International Nuclear Information System (INIS)

Hamm, E.

1994-01-01

In Germany the research funds for the mining industry will again be cut drastically in future. Cubis must plan and use the remaining research funds in an optimum manner in conjunction with the mining industry itself and also the mining supply industry. Close cooperation and continuous coordination between the research institutes and industrial partners will continue to be necessary for this purpose. Transfer of technology between research and industrial application must take place more smoothly. It is not a question of marketing the implementation of results of individual research and development projects; on the contrary system solutions from one source are required and offered. Long-term business relationships with industrial partners, within the framework of which contract research, advice, engineering, training, etc. can be realised, are desirable. Cubis has undertaken the responsibility to make available services to the mining industry and involve itself in new markets with the released capacities. The success so far achieved by the new company shows that competence and potential to face up to the large tasks exist. Cubis is equipped to tackle the continuous challenge of technology and safety at work, but also the tasks in the raw material and environment sectors in the nineties and is the suitable partner for solution of problems. (orig.)

Mining: The beginning and the end of the nuclear cycle

International Nuclear Information System (INIS)

Walls, J.

1991-01-01

Mining is one of the world's oldest industries, with a rich history that has evolved into modern times. A new chapter in that history is currently being written in southeastern New Mexico at the Waste Isolation Pilot Plant (WIPP). The beginning phase of the nuclear industry occurred when uranium was mined from the underground and processed to develop the first fuel source for the nuclear industry. The WIPP may well be the final chapter in closing out the nuclear cycle by the disposal of nuclear waste 2,150 ft into the underground repository. The WIPP is a US Department of Energy project located ∼ 30 miles southeast of Carlsbad, New Mexico, where the nation's first underground engineered nuclear repository is being constructed. The WIPP site was selected because of its location amidst a 2,000-ft-thick bed that provides a remarkably stable rock formation for the permanent storage of nuclear waste. The WIPP has taken an industry that is steeped in the tradition of mining hard rock with brute force to yield the highest quantity and has married it to a concept that demands superior safety and has a conservative approach to produce the highest quality. The process has been refined and has produced cultural shock in the local attitude toward mining

Intervention strategies to eliminate truck-related fatalities in surface coal mining in West Virginia.

Science.gov (United States)

Zhang, Meng; Kecojevic, Vladislav

2016-01-01

The main objective of this review was to build upon a previous study on the root causes of truck-related fatalities in surface coal mining operations in West Virginia, and to develop intervention strategies to eliminate these fatalities. This review considers a two-pronged approach to accident prevention: one that is fundamental and traditional (safety regulations, training and education, and engineering of the work environment); and one that is innovative and creative (e.g., applying technological advances to better control and eliminate the root causes of accidents). Suggestions for improving current training and education system are proposed, and recommendations are provided on improving the safety of mine working conditions, specifically safety conditions on haul roads, dump sites, and loading areas. We also discuss various currently available technologies that can help prevent haul truck-related fatal accidents. The results of this review should be used by mine personnel to help create safer working conditions and decrease truck-related fatalities in surface coal mining.

Disposal of radioactive waste from mining and processing of mineral sands

International Nuclear Information System (INIS)

Hartley, B.M.

1993-01-01

All mineral sands products contain the naturally radioactive elements uranium and thorium and their daughters. The activity levels in the different minerals can vary widely and in the un mined state are frequently widely dispersed and add to the natural background radiation levels. Following mining, the minerals are concentrated to a stage where radiation levels can present an occupational hazard and disposal of waste can result in radiation doses in excess of the public limit. Chemical processing can release radioactive daughters, particularly radium, leading to the possibility of dispersal and resulting in widespread exposure of the public. The activity concentration in the waste can vary widely and different disposal options appropriate to the level of activity in the waste are needed. Disposal methods can range from dilution and dispersal of the material into the mine site, for untreated mine tailings, to off site disposal in custom built and engineered waste disposal facilities, for waste with high radionuclide content. The range of options for disposal of radioactive waste from mineral sands mining and processing is examined and the principles for deciding on the appropriate disposal option are discussed. The range of activities of waste from different downstream processing paths are identified and a simplified method of identifying potential waste disposal paths is suggested. 15 refs., 4 tabs

Realizatinon of “zero emission” of mining water effluents from Sasa mine

OpenAIRE

Mirakovski, Dejan; Doneva, Nikolinka; Hadzi-Nikolova, Marija; Gocevski, Borce

2015-01-01

Sasa mine continuously takes actions to minimize the environmental impact of mining activities, in order to fulfill the national legislation in the field of environmental protection which comply with European legislation. This paper shows the drainage system of the horizon 830, which is performed in order to prevent free leakage of mining groundwater, as a part of these actions. This system provides a zero emission of mining water in the environment from Sasa mine. Key words: mining water...

Sustainable rehabilitation of mining waste and acid mine drainage using geochemistry, mine type, mineralogy, texture, ore extraction and climate knowledge.

Science.gov (United States)

Anawar, Hossain Md

2015-08-01

The oxidative dissolution of sulfidic minerals releases the extremely acidic leachate, sulfate and potentially toxic elements e.g., As, Ag, Cd, Cr, Cu, Hg, Ni, Pb, Sb, Th, U, Zn, etc. from different mine tailings and waste dumps. For the sustainable rehabilitation and disposal of mining waste, the sources and mechanisms of contaminant generation, fate and transport of contaminants should be clearly understood. Therefore, this study has provided a critical review on (1) recent insights in mechanisms of oxidation of sulfidic minerals, (2) environmental contamination by mining waste, and (3) remediation and rehabilitation techniques, and (4) then developed the GEMTEC conceptual model/guide [(bio)-geochemistry-mine type-mineralogy- geological texture-ore extraction process-climatic knowledge)] to provide the new scientific approach and knowledge for remediation of mining wastes and acid mine drainage. This study has suggested the pre-mining geological, geochemical, mineralogical and microtextural characterization of different mineral deposits, and post-mining studies of ore extraction processes, physical, geochemical, mineralogical and microbial reactions, natural attenuation and effect of climate change for sustainable rehabilitation of mining waste. All components of this model should be considered for effective and integrated management of mining waste and acid mine drainage. Copyright © 2015 Elsevier Ltd. All rights reserved.

BIOMedical Search Engine Framework: Lightweight and customized implementation of domain-specific biomedical search engines.

Science.gov (United States)

Jácome, Alberto G; Fdez-Riverola, Florentino; Lourenço, Anália

2016-07-01

Text mining and semantic analysis approaches can be applied to the construction of biomedical domain-specific search engines and provide an attractive alternative to create personalized and enhanced search experiences. Therefore, this work introduces the new open-source BIOMedical Search Engine Framework for the fast and lightweight development of domain-specific search engines. The rationale behind this framework is to incorporate core features typically available in search engine frameworks with flexible and extensible technologies to retrieve biomedical documents, annotate meaningful domain concepts, and develop highly customized Web search interfaces. The BIOMedical Search Engine Framework integrates taggers for major biomedical concepts, such as diseases, drugs, genes, proteins, compounds and organisms, and enables the use of domain-specific controlled vocabulary. Technologies from the Typesafe Reactive Platform, the AngularJS JavaScript framework and the Bootstrap HTML/CSS framework support the customization of the domain-oriented search application. Moreover, the RESTful API of the BIOMedical Search Engine Framework allows the integration of the search engine into existing systems or a complete web interface personalization. The construction of the Smart Drug Search is described as proof-of-concept of the BIOMedical Search Engine Framework. This public search engine catalogs scientific literature about antimicrobial resistance, microbial virulence and topics alike. The keyword-based queries of the users are transformed into concepts and search results are presented and ranked accordingly. The semantic graph view portraits all the concepts found in the results, and the researcher may look into the relevance of different concepts, the strength of direct relations, and non-trivial, indirect relations. The number of occurrences of the concept shows its importance to the query, and the frequency of concept co-occurrence is indicative of biological relations

Philippine Mining Capitalism: The Changing Terrains of Struggle in the Neoliberal Mining Regime

Directory of Open Access Journals (Sweden)

Alvin A. Camba

2016-06-01

Full Text Available This article analyzes how the mining sector and anti-mining groups compete for mining outcomes in the Philippines. I argue that the transition to a neoliberal mineral regime has empowered the mining sector and weakened the mining groups by shifting the terrains of struggle onto the domains of state agencies and scientific networks. Since the neoliberal era, the mining sector has come up with two strategies. First, technologies of subjection elevate various public institutions to elect and select the processes aimed at making mining accountable and sensitive to the demands of local communities. However, they often refuse or lack the capacity to intervene effectively. Second, technologies of subjectivities allow a selective group of industry experts to single-handedly determine the environmental viability of mining projects. Mining consultants, specialists, and scientists chosen by mining companies determine the potential environmental damage on water bodies, air pollution, and soil erosion. Because of the mining capital’s access to economic and legal resources, anti-mining communities across the Philippines have been forced to compete on an unequal terrain for a meaningful social dialogue and mining outcomes.

Nursing, Nursing Education, and Anxiety.

Science.gov (United States)

Biggers, Thompson; And Others

In response to the current crisis in the field of nursing, a study examined nursing students' perceived work-related stress and differences among associate degree, diploma, and baccalaureate nursing programs in their preparation of nursing students. The 171 subjects, representing the three different nursing programs, completed a questionnaire…

Kiruna research mine

Energy Technology Data Exchange (ETDEWEB)

Oestensen, A

1983-12-01

The research mine at Kiruna is the first large-scale mining research project sponsored by the Swedish government. Under the leadership of the Swedish Mining Research Foundation, a five-year project involving development of new mining systems and machinery will be carried out in cooperation with the Lulea Institute of Technology and a number of Swedish industrial companies.

Analysis of the situation of Spanish metal mining; Analisis de situacion de la mineria metalica espanola

Energy Technology Data Exchange (ETDEWEB)

Espi Rodriguez, J. A.; Vazquez Guzman, F.; Leon Altamirano, C.; Perez Macias, D.

2015-07-01

This article is a summary of the original document drawn up by the Task Force on Mineral Resources and Reserves of the National Association of Mining Engineers, available in free digital format through the Link. (Author)

Dual-fuel natural gas/diesel engines: Technology, performance, and emissions

Science.gov (United States)

Turner, S. H.; Weaver, C. S.

1994-11-01

An investigation of current dual-fuel natural gas/diesel engine design, performance, and emissions was conducted. The most pressing technological problems associated with dual-fuel engine use were identified along with potential solutions. It was concluded that dual-fuel engines can achieve low NO(sub x) and particulate emissions while retaining fuel-efficiency and BMEP levels comparable to those of diesel engines. The investigation also examined the potential economic impact of dual-fuel engines in diesel-electric locomotives, marine vessels, farm equipment, construction, mining, and industrial equipment, and stand-alone electricity generation systems. Recommendations for further additional funding to support research, development, and demonstration in these applications were then presented.

Relationship of 220Rn and 222Rn progeny levels in Canadian underground U mines

International Nuclear Information System (INIS)

Bigu, J.

1988-01-01

Radon-222 and 220 Rn progeny are found in some Canadian underground U mines. Because both can contribute to lung dose, their experimental determinations are important. The relationship between 222 Rn progeny Working Level [WL(Rn)] and 220 Rn progeny Working Level [WL(Tn)] has been investigated in U mines. Experimental measurements extended from 1981 to 1986 and consisted of about 700 measurements of each WL(Rn) and WL(Tn). The data were analyzed by standard linear and power-function regression analysis. A power-function relationship between WL(Rn) and WL(Tn) seemed to fit the experimental data best. The relationship obtained permits the calculation of WL(Tn) from experimental values of WL(Rn). The relationship is useful for lung-dose-calculation purposes and in mine-ventilation-engineering calculations

Overview of mine drainage geochemistry at historical mines, Humboldt River basin and adjacent mining areas, Nevada. Chapter E.

Science.gov (United States)

Nash, J. Thomas; Stillings, Lisa L.

2004-01-01

Reconnaissance hydrogeochemical studies of the Humboldt River basin and adjacent areas of northern Nevada have identified local sources of acidic waters generated by historical mine workings and mine waste. The mine-related acidic waters are rare and generally flow less than a kilometer before being neutralized by natural processes. Where waters have a pH of less than about 3, particularly in the presence of sulfide minerals, the waters take on high to extremely high concentrations of many potentially toxic metals. The processes that create these acidic, metal-rich waters in Nevada are the same as for other parts of the world, but the scale of transport and the fate of metals are much more localized because of the ubiquitous presence of caliche soils. Acid mine drainage is rare in historical mining districts of northern Nevada, and the volume of drainage rarely exceeds about 20 gpm. My findings are in close agreement with those of Price and others (1995) who estimated that less than 0.05 percent of inactive and abandoned mines in Nevada are likely to be a concern for acid mine drainage. Most historical mining districts have no draining mines. Only in two districts (Hilltop and National) does water affected by mining flow into streams of significant size and length (more than 8 km). Water quality in even the worst cases is naturally attenuated to meet water-quality standards within about 1 km of the source. Only a few historical mines release acidic water with elevated metal concentrations to small streams that reach the Humboldt River, and these contaminants and are not detectable in the Humboldt. These reconnaissance studies offer encouraging evidence that abandoned mines in Nevada create only minimal and local water-quality problems. Natural attenuation processes are sufficient to compensate for these relatively small sources of contamination. These results may provide useful analogs for future mining in the Humboldt River basin, but attention must be given to